WorldWideScience

Sample records for stage final static

  1. Bevalac injector final stage RF amplifier upgrades

    International Nuclear Information System (INIS)

    Howard, D.; Calvert, J.; Dwinell, R.; Lax, J.; Lindner, A.; Richter, R.; Ridgeway, W.

    1991-01-01

    With the assistance of the DOE In-house Energy Management Program, the Bevalac injector final stage RF amplifier systems have been successfully upgraded to reduce energy consumption and operating costs. This recently completed project removed the energy-inefficient plate voltage modulator circuits that were used in conjunction with the final stage RF amplifiers. Construction, design, and operating parameters are described in detail

  2. Static Heat Loads in the LHC Arc Cryostats: Final Assessment

    CERN Document Server

    Parma, V

    2010-01-01

    This note presents the final assessment of the static heat loads in the LHC arc cryostats, using different experimental methods during the first commissioning period in 2007. This assessment further develops and completes previous estimates made during the commissioning of sector 7_8 [1]. The estimate of the helium inventory, a prerequisite for the heat load calculation, is also presented. Heat loads to the cold mass are evaluated from the internal energy balance during natural as well as powered warm-ups of the helium baths in different subsector. The helium inventory is calculated from the internal energy balance during powered warm-ups and matched with previous assessments. Furthermore, heat loads to the thermal shield are estimated from the non-isothermal cooling of the supercritical helium in line E. The comparison of measured heat loads with previous estimates and with budgeted values is then presented, while their correlation with some important parameters like insulation vacuum pressure and some heat ...

  3. Advanced high temperature static strain sensor development. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Hulse, C.O.; Stetson, K.A.; Grant, H.P.; Jameikis, S.M.; Morey, W.W.; Raymondo, P.; Grudkowski, T.W.; Bailey, R.S.

    1986-08-01

    An examination was made into various techniques to be used to measure static strain in gas turbine liners at temperatures up to 1150 K (1600 F). The methods evaluated included thin film and wire resistive devices, optical fibers, surface acoustic waves, the laser speckle technique with a heterodyne readout, optical surface image and reflective approaches and capacitive devices. A preliminary experimental program to develop a thin film capacitive device was dropped because calculations showed that it would be too sensitive to thermal gradients. In a final evaluation program, the laser speckle technique appeared to work well up to 1150 K when it was used through a relatively stagnant air path. The surface guided acoustic wave approach appeared to be interesting but to require too much development effort for the funds available. Efforts to develop a FeCrAl resistive strain gage system were only partially successful and this part of the effort was finally reduced to a characterization study of the properties of the 25 micron diameter FeCrAl (Kanthal A-1) wire. It was concluded that this particular alloy was not suitable for use as the resistive element in a strain gage above about 1000 K.

  4. Static Scale Conversion Weigh-In-Motion System; FINAL

    International Nuclear Information System (INIS)

    Beshears, D.L.

    2001-01-01

    In support of the Air Mobility Battle Lab (AMBL), the Defense Advanced Research Projects Agency (DARPA) Advanced Logistics Program and the U. S. Transportation Command (USTRANSCOM), the ultimate objective of this project is to develop and demonstrate a full-scale prototype static scale conversion weigh-in-motion/Profilometry (SSC-WIM/P) system to measure and record dimensional and weight information for the Department of Defense (DoD) equipment and cargo. The Oak Ridge National Laboratory (ORNL), along with the AMBL, and Intercomp, Inc. have developed a long-range plan for developing a dual-use system which can be used as a standard static scale or an accurate weigh-in-motion system. AMBL will work to define requirements for additional activities with U.S. Transportation Command, Air Mobility Command, and the Joint Warfighting Battle Lab for both the SSC-WIM/P and a portable Weigh-in-Motion System for individual units. The funding goal is to fully fund the development of two prototype test articles (a SSC-WIM kit, and a laser profilometer) and have at least one fully operational system by the early 2002 timeframe. The objective of this portion of the project will be to develop a SSC-WIM system, which at a later date can be fully integrated with a profilometry system; to fully characterize DOD wheeled vehicles and cargo (individual axle weights, total vehicle weight, center of balance, height, width and length measurements). The program will be completed in phases with the initial AMBL/DARPA funding being used to initiate the efforts while AMBL/USTC obtains funding to complete the first generation system effort. At the completion of an initial effort, the interface hardware and the data acquisition/analysis hardware will be developed, fabricated, and system principles and basic functionality evaluated, tested, and demonstrated. Additional funding, when made available, will allow the successful completion of a first generation prototype system. This effort will be

  5. Dynamical processes at the final stage of nuclear fission

    International Nuclear Information System (INIS)

    Rubchenya, V.A.; Yavshits, S.G.

    1984-01-01

    A model of the final stage of fission near the scission point is proposed. The processes of nucleon exchange through sub-barrier transitions between the fragments are considered within the framework of this model in the diffusion approximation. For the determination of the initial conditions a method by which the transition from the one-center configuration of the nucleus before scission to a fragment-system configuration can be made, and which relates the stage in question to the stage at which the descent from the saddle point occurs, is formulated. The model parameters, the transport coefficients, and the mass distributions of the fragments are found for two cases: the low- and high-energy fission of the 236 U compound nucleus. The results are compared with the experimental data

  6. Autoclaved metal-on-cement spacer versus static spacer in two-stage revision in periprosthetic knee infection

    Directory of Open Access Journals (Sweden)

    Yu-Pin Chen

    2016-01-01

    Conclusions: The autoclaved metal-on-cement spacer is an effective and simple method for two-stage re-implantation of a periprosthetic knee infection. Through this spacer, the good interim ROM can be achieved without the additional cost of prefabricated molds or new polyethylene tibial inserts. In addition, ROM after re-implantation is better than that with static spacers.

  7. The European Dioxin Emission Inventory. Stage II. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Quass, U.; Fermann, M.; Broeker, G.

    2001-07-01

    For Stage II of the European Dioxin Project the following objectives were set: - Amendment of existing emission data collected for most relevant emission sources in order to reduce uncertainties of emission estimates. Collecting first emission data from countries not yet performing dioxin emission measurement programs. Extending the inventory of dioxin emissions to ambient air produced in Stage I by a complementary study on emissions to land and water. Extending the regional scope of data collection to countries in Central Europe. The report of Stage II of the European Dioxin Project is presented in 3 Volumes. Volume 1 contains an overview on the background and approach of different activities carried out and on the results obtained. These results are put into a broader view regarding the dioxin reduction measures in Europe leading to conclusions and recommendation for future work. Volume 2 of the report contains a detailed presentation of the sub-projects carried out. The chapters of Volume 2 are structured in a similar manner and start with a short summary in order to allow for a fast cross-reading. In the case of the desk-top studies an overview of the main results or statements is given. Regarding emission measurements details on the experimental set-up and the facilities being investigated are presented. Volume 3 contains a re-evaluation of the dioxin emission inventory presented for the most relevant sources types in the Stage I report. New data gathered from the projects of Stage II as well as from independent activities in the European countries are considered for a revision of the 1995 emission estimates. Additionally, based on current trends and activities the PCDD/F emissions for the years 2000 and 2005 are estimated. Finally, an attempt is made to evaluate the PCDD/F emission reduction rates which might be possible to achieve by the year 2005 compared to 1985. (orig.)

  8. 4 Kelvin Cooling with Innovative Final Stage of Multistage Cryocooler, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Proposed for development is a proof-of-concept prototype for the final stage of a multistage cryocooler. This final stage comprises a high frequency pulse tube cold...

  9. The Final Stages of Massive Star Evolution and Their Supernovae

    Science.gov (United States)

    Heger, Alexander

    In this chapter I discuss the final stages in the evolution of massive stars - stars that are massive enough to burn nuclear fuel all the way to iron group elements in their core. The core eventually collapses to form a neutron star or a black hole when electron captures and photo-disintegration reduce the pressure support to an extent that it no longer can hold up against gravity. The late burning stages of massive stars are a rich subject by themselves, and in them many of the heavy elements in the universe are first generated. The late evolution of massive stars strongly depends on their mass, and hence can be significantly effected by mass loss due to stellar winds and episodic mass loss events - a critical ingredient that we do not know as well as we would like. If the star loses all the hydrogen envelope, a Type I supernova results, if it does not, a Type II supernova is observed. Whether the star makes neutron star or a black hole, or a neutron star at first and a black hole later, and how fast they spin largely affects the energetics and asymmetry of the observed supernova explosion. Beyond photon-based astronomy, other than the sun, a supernova (SN 1987) has been the only object in the sky we ever observed in neutrinos, and supernovae may also be the first thing we will ever see in gravitational wave detectors like LIGO. I conclude this chapter reviewing the deaths of the most massive stars and of Population III stars.

  10. Static reactive power compensators for high-voltage power systems. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1981-04-01

    A study conducted to summarize the role of static reactive power compensators for high voltage power system applications is described. This information should be useful to the utility system planning engineer in applying static var systems (SVS) to high voltage as (HVAC) systems. The static var system is defined as a form of reactive power compensator. The general need for reactive power compensation in HVAC systems is discussed, and the static var system is compared to other devices utilized to provide reactive power compensation. Examples are presented of applying SVS for specific functions, such as the prevention of voltage collapse. The operating principles of commercially available SVS's are discussed in detail. The perormance and active power loss characteristics of SVS types are compared.

  11. Orbit determination for the final stages of the GOCE mission

    Science.gov (United States)

    Visser, Pieter N. A. M.; Van Den IJssel, Jose

    The European Space Agency (ESA) Gravity field and steady-state Ocean Circulation Explorer (GOCE) re-entered the Earth's atmosphere on 11 November 2013, ending more than four years of successful mission operations. On 21 October 2013, the GOCE ion engines stopped functioning thereby ending its Drag-Free orbital motion. From then on, the satellite started decaying at increasing speeds and the atmospheric drag was growing exponentially towards its demise. Data from the GOCE Global Positioning System (GPS) receiver and accelerometers were collected down to an altitude of 137 km. The accelerometers started to get saturated on 7 November 2011 at an altitude of around 190 km, but kept on partially working until the altitude of 137 km as well. The data set of GPS and accelerometer observations for the last weeks of GOCE form a unique data set for testing GPS-based orbit determination in a high drag environment. Moreover, GPS-based estimates of the predominantly atmospheric drag induced non-gravitational accelerations can be validated against the accelerometer observations for this environment as well. This presentation will highlight precise orbit determination results and comparisons between accelerometer observations and GPS-based estimates of non-gravitational accelerations for the final stages of the GOCE mission.

  12. The Final Stage of Gravitationally Collapsed Thick Matter Layers

    Directory of Open Access Journals (Sweden)

    Piero Nicolini

    2013-01-01

    Full Text Available In the presence of a minimal length, physical objects cannot collapse to an infinite density, singular, matter point. In this paper, we consider the possible final stage of the gravitational collapse of “thick” matter layers. The energy momentum tensor we choose to model these shell-like objects is a proper modification of the source for “noncommutative geometry inspired,” regular black holes. By using higher momenta of Gaussian distribution to localize matter at finite distance from the origin, we obtain new solutions of the Einstein equation which smoothly interpolates between Minkowski’s geometry near the center of the shell and Schwarzschild’s spacetime far away from the matter layer. The metric is curvature singularity free. Black hole type solutions exist only for “heavy” shells; that is, M ≥Me, where Me is the mass of the extremal configuration. We determine the Hawking temperature and a modified area law taking into account the extended nature of the source.

  13. Two-stage revision of septic knee prosthesis with articulating knee spacers yields better infection eradication rate than one-stage or two-stage revision with static spacers.

    Science.gov (United States)

    Romanò, C L; Gala, L; Logoluso, N; Romanò, D; Drago, L

    2012-12-01

    The best method for treating chronic periprosthetic knee infection remains controversial. Randomized, comparative studies on treatment modalities are lacking. This systematic review of the literature compares the infection eradication rate after two-stage versus one-stage revision and static versus articulating spacers in two-stage procedures. We reviewed full-text papers and those with an abstract in English published from 1966 through 2011 that reported the success rate of infection eradication after one-stage or two-stage revision with two different types of spacers. In all, 6 original articles reporting the results after one-stage knee exchange arthoplasty (n = 204) and 38 papers reporting on two-stage revision (n = 1,421) were reviewed. The average success rate in the eradication of infection was 89.8% after a two-stage revision and 81.9% after a one-stage procedure at a mean follow-up of 44.7 and 40.7 months, respectively. The average infection eradication rate after a two-stage procedure was slightly, although significantly, higher when an articulating spacer rather than a static spacer was used (91.2 versus 87%). The methodological limitations of this study and the heterogeneous material in the studies reviewed notwithstanding, this systematic review shows that, on average, a two-stage procedure is associated with a higher rate of eradication of infection than one-stage revision for septic knee prosthesis and that articulating spacers are associated with a lower recurrence of infection than static spacers at a comparable mean duration of follow-up. IV.

  14. Dental Age Estimation (DAE): Data management for tooth development stages including the third molar. Appropriate censoring of Stage H, the final stage of tooth development.

    Science.gov (United States)

    Roberts, Graham J; McDonald, Fraser; Andiappan, Manoharan; Lucas, Victoria S

    2015-11-01

    The final stage of dental development of third molars is usually helpful to indicate whether or not a subject is aged over 18 years. A complexity is that the final stage of development is unlimited in its upper border. Investigators usually select an inappropriate upper age limit or censor point for this tooth development stage. The literature was searched for appropriate data sets for dental age estimation and those that provided the count (n), the mean (x¯), and the standard deviation (sd) for each of the tooth development stages. The Demirjian G and Demirjian H were used for this study. Upper and lower limits of the Stage G and Stage H data were calculated limiting the data to plus or minus three standard deviations from the mean. The upper border of Stage H was limited by appropriate censoring at the maximum value for Stage G. The maximum age at attainment from published data, for Stage H, ranged from 22.60 years to 34.50 years. These data were explored to demonstrate how censoring provides an estimate for the correct maximum age for the final stage of Stage H as 21.64 years for UK Caucasians. This study shows that confining the data array of individual tooth developments stages to ± 3sd provides a reliable and logical way of censoring the data for tooth development stages with a Normal distribution of data. For Stage H this is inappropriate as it is unbounded in its upper limit. The use of a censored data array for Stage H using Percentile values is appropriate. This increases the reliability of using third molar Stage H alone to determine whether or not an individual is over 18 years old. For Stage H, individual ancestral groups should be censored using the same technique. Copyright © 2015 Elsevier Ltd and Faculty of Forensic and Legal Medicine. All rights reserved.

  15. Staging and storage facility feasibility study. Final report

    International Nuclear Information System (INIS)

    Swenson, C.E.

    1995-02-01

    This study was performed to investigate the feasibility of adapting the design of the HWVP Canister Storage Building (CSB) to meet the needs of the WHC Spent Nuclear Fuel Project for Staging and Storage Facility (SSF), and to develop Rough Order of Magnitude (ROM) cost and schedule estimates

  16. Static and dynamic analysis of 1 220 mm steel last stage blade for steam turbine

    Directory of Open Access Journals (Sweden)

    Kubín Z.

    2009-06-01

    Full Text Available The 3 000 rpm 1 220 mm blade for a steam turbine was developed with application of new design features. The last stage moving blade is designed with an integral cover, a mid-span tie-boss connection and a fir-tree dovetail. With this configuration the blades are continuously coupled by the blade untwist due to the centrifugal force when the blades rotate at high speed, so that vibration control and increased structural damping are provided. Blade was tuned in order to eigen-frequencies were safely far from possible excitation. Because of connection members, the number of the resonant vibration modes can be reduced by virtue of the vibration characteristics of the circumferentially continuous blades. The last stage airfoil was optimalized from view of minimalization of its centrifugal force. In order to develop the 3 000 rpm 1 220 mm blade, the advanced analysis methods to predict dynamics behavior of the bladed structure were applied. Coupled rotor-blade analysis was also aim of the attention. To validate calculated results the verification measurement such as rotational vibration tests was carried out in the high-speed test rig. Relation of the friction damping of the bladed structure on amount of excitation level was also monitored and evaluated.

  17. Undesirable dispersal of eggs and early-stage nymphs of the bed bug Hemiptera: cimicidae) by static electricity and air currents

    Science.gov (United States)

    Movement of whole live insects or other small arthropods attributed to static electricity has been reported only rarely. While viewing bed bugs in plastic or glass Petri dishes using a dissecting microscope, individual eggs and early stage nymphs were occasionally observed to move suddenly and rapid...

  18. Seafood-Processing Sludge Composting: Changes to Microbial Communities and Physico-Chemical Parameters of Static Treatment versus for Turning during the Maturation Stage.

    Science.gov (United States)

    Villar, Iria; Alves, David; Mato, Salustiano

    2016-01-01

    In general, in composting facilities the active, or intensive, stage of the process is done separately from the maturation stage, using a specific technology and time. The pre-composted material to be matured can contain enough biodegradable substrates to cause microbial proliferation, which in turn can cause temperatures to increase. Therefore, not controlling the maturation period during waste management at an industrial level can result in undesired outcomes. The main hypothesis of this study is that controlling the maturation stage through turning provides one with an optimized process when compared to the static approach. The waste used was sludge from a seafood-processing plant, mixed with shredded wood (1:2, v/v). The composting system consists of an intensive stage in a 600L static reactor, followed by maturation in triplicate in 200L boxes for 112 days. Two tests were carried out with the same process in reactor and different treatments in boxes: static maturation and turning during maturation when the temperature went above 55°C. PLFAs, organic matter, pH, electrical conductivity, forms of nitrogen and carbon, hydrolytic enzymes and respiratory activity were periodically measured. Turning significantly increased the duration of the thermophilic phase and consequently increased the organic-matter degradation. PCA differentiated significantly the two treatments in function of tracking parameters, especially pH, total carbon, forms of nitrogen and C/N ratio. So, stability and maturity optimum values for compost were achieved in less time with turnings. Whereas turning resulted in microbial-group stabilization and a low mono/sat ratio, static treatment produced greater variability in microbial groups and a high mono/sat ratio, the presence of more degradable substrates causes changes in microbial communities and their study during maturation gives an approach of the state of organic-matter degradation. Obtaining quality compost and optimizing the composting

  19. Study of static reactive power compensators for high-voltage power systems. Final report, May 12, 1981

    Energy Technology Data Exchange (ETDEWEB)

    Byerly, R.T.; Bennon, R.J.; Taylor, E.R. Jr.; Poznaniak, D.T.

    1981-05-12

    A general study of the application of static VAR compensators (SVC's) to high-voltage transmission systems has been performed. Considerable emphasis has been placed on improvements to synchronous stability, and it is shown that SVC's can provide significant benefits in terms of damping for unstable modes of oscillation and increases in transient stability limits. This report includes descriptions of static VAR compensators, technical and economic comparisons of different compensators, compensator models for system studies, comprehensive study procedures, study results for two small-scale systems, and guidelines for SVC application.

  20. Inventory of platforms towards the design of a statically balanced six degrees of freedom compliant precision stage

    NARCIS (Netherlands)

    Dunning, A.G.; Tolou, N.; Herder, J.

    2011-01-01

    For many applications in precision engineering, a six degrees of freedom (DoF) compliant stage (CS) with zero stiffness is desirable, to deal with problems like backlash, friction, lubrication, and at the same time, reduce the actuation force. To this end, the compliant stage (also known as

  1. Research and development program in reactor diagnostics and monitoring with neutron noise methods. Stage 6. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Pazsit, I.; Demaziere, C.; Avdic, S.; Dahl, B. [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Reactor Physics

    2000-07-15

    by a finite difference scheme, similar to the one used in the previous stage. Actually, a relatively large and involved computational tool was elaborated, containing several modules. In the first module the static, space-dependent group constants are generated, to be used as input by the finite difference dynamic code. These are calculated through CASMO/SIMULATE for a realistic heterogeneous core. The dynamic code then calculates the noise for a number of hypothetical perturbations. The perturbations can be given either as direct changes in the cross-sections, or changes in the temperature of various components (coolant, fuel etc.). In the latter case the temperature fluctuations are converted into cross-section fluctuations by another module. Finally the noise is calculated in two or three dimensions by using the static group constants, the time derivatives, the delayed neutron data and the perturbations data. By a suitable choice of the perturbation, the Green's function can also be calculated, from which the noise induced by other perturbations can be calculated by integration. The model was verified through comparison to analytical calculations. It has been proposed a long time ago that the cross-correlation or coherence between the neutron noise, measured locally in the core, and the core-exit thermocouples can be used to determine the MTC. Such a method would have large advantages over the traditional ones because it would not interfere with the reactor operation. Earlier investigations showed nevertheless that the MTC value, obtained from such investigations, gave a quantitative value for the MTC that was 2 to 5 times lower than the true one. One very likely reason for this deviation lies in the fact that in the evaluation of the noise measurement, it is assumed that the temperature fluctuations, driving the neutron noise, are homogeneously distributed in the core, and that the response of the reactor is point-kinetic. In reality none of these two

  2. Optimization study of the explicit finite-difference method for quasi-static thermomechanical simulations. Final report

    International Nuclear Information System (INIS)

    Maxwell, D.E.; Hofmann, R.; Wahi, K.K.

    1978-03-01

    The developments presented make it economically feasible to use a time-explicit numerical code to perform thermomechanical simulations of quasi-static systems that incorporate physically small source regions (or centers of activity) in a relatively large space. A nuclear waste repository in a geological medium is an example of such a system. The technique developed make it possible to eliminate two major restrictions that explicit-finite difference codes generally have that can considerably limit their efficiency. The technique is a time-step optimization method called pseudo-time steps (PTS). This report describes the motivation, derivation, and implementation of the PTS method

  3. Independent channels for miRNA biosynthesis ensure efficient static and dynamic control in the regulation of the early stages of myogenesis.

    Science.gov (United States)

    Fiorentino, Jonathan; De Martino, Andrea

    2017-10-07

    Motivated by recent experimental work, we define and study a deterministic model of the complex miRNA-based regulatory circuit that putatively controls the early stage of myogenesis in human. We aim in particular at a quantitative understanding of (i) the roles played by the separate and independent miRNA biosynthesis channels (one involving a miRNA-decoy system regulated by an exogenous controller, the other given by transcription from a distinct genomic locus) that appear to be crucial for the differentiation program, and of (ii) how competition to bind miRNAs can efficiently control molecular levels in such an interconnected architecture. We show that optimal static control via the miRNA-decoy system constrains kinetic parameters in narrow ranges where the channels are tightly cross-linked. On the other hand, the alternative locus for miRNA transcription can ensure that the fast concentration shifts required by the differentiation program are achieved, specifically via non-linear response of the target to even modest surges in the miRNA transcription rate. While static, competition-mediated regulation can be achieved by the miRNA-decoy system alone, both channels are essential for the circuit's overall functionality, suggesting that that this type of joint control may represent a minimal optimal architecture in different contexts. Copyright © 2017 Elsevier Ltd. All rights reserved.

  4. Static Analysis Numerical Algorithms

    Science.gov (United States)

    2016-04-01

    STATIC ANALYSIS OF NUMERICAL ALGORITHMS KESTREL TECHNOLOGY, LLC APRIL 2016 FINAL TECHNICAL REPORT APPROVED FOR PUBLIC RELEASE; DISTRIBUTION...3. DATES COVERED (From - To) NOV 2013 – NOV 2015 4. TITLE AND SUBTITLE STATIC ANALYSIS OF NUMERICAL ALGORITHMS 5a. CONTRACT NUMBER FA8750-14-C...and Honeywell Aerospace Advanced Technology to combine model-based development of complex avionics control software with static analysis of the

  5. Two-stage continuous process of methyl ester from high free fatty acid mixed crude palm oil using static mixer coupled with high-intensity of ultrasound

    International Nuclear Information System (INIS)

    Somnuk, Krit; Smithmaitrie, Pruittikorn; Prateepchaikul, Gumpon

    2013-01-01

    Highlights: • Mixed crude palm oil was used in the two-step continuous process. • Two-step continuous process was performed using static mixer coupled with ultrasound. • The maximum obtained yield was 92.5 vol.% after the purification process. • The residence time less than 20 s was achieved in ultrasonic reactors. - Abstract: The two-stage continuous process of methyl ester from high free fatty acid (FFA) mixed crude palm oil (MCPO) was performed by using static mixer coupled with high-intensity of ultrasound. The 2 × 1000 W ultrasonic homogenizers were operated at 18 kHz frequency in the 2 × 100 mL continuous reactors. For the first-step, acid-catalyzed esterification was employed with 18 vol.% of methanol, 2.7 vol.% of sulfuric acid, 60 °C of temperature, and 20 L h −1 of MCPO flow rate, for reducing the acid value from 28 mg KOH g −1 to less than 2 mg KOH g −1 . For the second-step, base-catalyzed transesterification was carried out under 18 vol.% of methanol, 8 g KOH L −1 of oil, and 20 L h −1 of esterified oil flow rate at 30 °C. The high yields of esterified oil and crude biodiesel were attained within the residence time of less than 20 s in the ultrasonic reactors. The yields of each stage process were: 103.3 vol.% of esterified oil, 105.4 vol.% of crude biodiesel, and 92.5 vol.% of biodiesel when compared with 100 vol.% MCPO. The quality of the biodiesel meets the specification of biodiesel standard in Thailand

  6. Close set in volleyball. Differences and discriminatory power of final game actions in formative stages

    Directory of Open Access Journals (Sweden)

    Dávila Romero, Carlos

    2012-01-01

    Full Text Available The aim of this study was to establish which final game actions discriminate final victories and defeats in women volleyball formative stages during ended sets, which are solved by regulation with a minimal advantage of two points. A total of 57 sets were analyzed in infantile category and 69 sets in cadet category during the national volleyball championship at school age (12-16, Valladolid 2008 and Huelva 2009. Statistics analysis shows differences between the condition of both the winner and the loser teams in sets in the positive attack in infantile category and in positive block and error in cadet category. Discriminative analysis, statistical test that determines those most significant game actions when establishing the differences existing between the winner and loser teams, shows how to predict victory and defeat in the ended sets regarding the positive attack, negative service and error in infantile category and positive block and error in cadet category. These ones suggest that during decisive set moments in both categories, either technical gestures control or errors which arise from a regulation infraction may predict their final performance.

  7. The Romanian Question at the Final Stage of the Eastern Crisis 1875-1878

    Directory of Open Access Journals (Sweden)

    Victor Drozdov

    2015-08-01

    Full Text Available One of the important results of the Eastern crisis 1875-1878 was а change of the political map of the Balkan and the recognition of new states, including Romania. The declaration of independence of Romania, the participation of Romanian troops in the war against Turkey and the territorial dispute between Romania and Russia over South Bessarabia led to the actualization of the Romanian question in European diplomacy. The policy of Romania in the final stage of the Eastern crisis 1875-1878 and the process of solution the Romanian question at the Congress of Berlin in 1878 were analyzed in the article. The author focuses on the deterioration of Russian-Romanian relations as a result of the emergence of territorial disputes over South Bessarabia.

  8. Results of comparative RBMK neutron computation using VNIIEF codes (cell computation, 3D statics, 3D kinetics). Final report

    Energy Technology Data Exchange (ETDEWEB)

    Grebennikov, A.N.; Zhitnik, A.K.; Zvenigorodskaya, O.A. [and others

    1995-12-31

    In conformity with the protocol of the Workshop under Contract {open_quotes}Assessment of RBMK reactor safety using modern Western Codes{close_quotes} VNIIEF performed a neutronics computation series to compare western and VNIIEF codes and assess whether VNIIEF codes are suitable for RBMK type reactor safety assessment computation. The work was carried out in close collaboration with M.I. Rozhdestvensky and L.M. Podlazov, NIKIET employees. The effort involved: (1) cell computations with the WIMS, EKRAN codes (improved modification of the LOMA code) and the S-90 code (VNIIEF Monte Carlo). Cell, polycell, burnup computation; (2) 3D computation of static states with the KORAT-3D and NEU codes and comparison with results of computation with the NESTLE code (USA). The computations were performed in the geometry and using the neutron constants presented by the American party; (3) 3D computation of neutron kinetics with the KORAT-3D and NEU codes. These computations were performed in two formulations, both being developed in collaboration with NIKIET. Formulation of the first problem maximally possibly agrees with one of NESTLE problems and imitates gas bubble travel through a core. The second problem is a model of the RBMK as a whole with imitation of control and protection system controls (CPS) movement in a core.

  9. Results of comparative RBMK neutron computation using VNIIEF codes (cell computation, 3D statics, 3D kinetics). Final report

    International Nuclear Information System (INIS)

    Grebennikov, A.N.; Zhitnik, A.K.; Zvenigorodskaya, O.A.

    1995-01-01

    In conformity with the protocol of the Workshop under Contract open-quotes Assessment of RBMK reactor safety using modern Western Codesclose quotes VNIIEF performed a neutronics computation series to compare western and VNIIEF codes and assess whether VNIIEF codes are suitable for RBMK type reactor safety assessment computation. The work was carried out in close collaboration with M.I. Rozhdestvensky and L.M. Podlazov, NIKIET employees. The effort involved: (1) cell computations with the WIMS, EKRAN codes (improved modification of the LOMA code) and the S-90 code (VNIIEF Monte Carlo). Cell, polycell, burnup computation; (2) 3D computation of static states with the KORAT-3D and NEU codes and comparison with results of computation with the NESTLE code (USA). The computations were performed in the geometry and using the neutron constants presented by the American party; (3) 3D computation of neutron kinetics with the KORAT-3D and NEU codes. These computations were performed in two formulations, both being developed in collaboration with NIKIET. Formulation of the first problem maximally possibly agrees with one of NESTLE problems and imitates gas bubble travel through a core. The second problem is a model of the RBMK as a whole with imitation of control and protection system controls (CPS) movement in a core

  10. Research and Development Program in Reactor Diagnostics and Monitoring with Neutron Noise Methods. Stage 11 and 12. Final report

    International Nuclear Information System (INIS)

    Sunde, C.; Pazsit, I.; Demaziere, C.; Dahl, O.; Mileshina, L.

    2006-06-01

    This report describes the results obtained during Stage 11 and 12 of a long-term research and development program concerning the development of diagnostics and monitoring methods for nuclear reactors. The long-term goals are elaborated in more detail in e.g. the Final Reports of stage 1 and 2 (SKI Report 95:14 and 96:50). Higher order eigenfunctions and eigenvalues of the diffusion equation, describing a static core, have lost their significance when doing calculations in realistic systems, since there are usually made by nodal methods or other direct numerical techniques. However, there are situations when knowledge of the higher order modes is still useful. Such case is the separation of the global and regional flux oscillations in the case of BWR instability. Another case is the investigation of the stability properties of large inhomogeneous cores, which is usually quantified with the so-called eigenvalue separation, ES=1/k 1 - 1/k 0 where k 0 and k 1 , are the fundamental and first higher order eigenvalues, respectively. Numerical codes used for ICMF calculations usually do not have the option of calculating the higher order eigenvalues and eigenfunctions. In idealised systems, these can be calculated with semi-analytical methods. In order to get insight into the characteristics of the higher order eigenmodes of the neutron flux and the adjoint, these were calculated in a reflected homogeneous system with two-group theory. The adjoint eigenmodes are necessary if an orthogonality property needs to be used, such as the separation of the modes from a flux shape which is a sum of several eigenmodes. At the same time, the so-called numerical noise simulator, developed at the Dept., was extended such that it became suitable for the calculation of the higher order eigenmodes, both direct and adjoint ones. This simulator can treat real inhomogeneous cores, with an input deck compatible with that of SIMULATE. The simulator was used to calculate the eigenfunctions and

  11. Research and Development Program in Reactor Diagnostics and Monitoring with Neutron Noise Methods. Stage 11 and 12. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Sunde, C.; Pazsit, I.; Demaziere, C.; Dahl, O.; Mileshina, L. [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Nuclear Engineering

    2006-06-15

    This report describes the results obtained during Stage 11 and 12 of a long-term research and development program concerning the development of diagnostics and monitoring methods for nuclear reactors. The long-term goals are elaborated in more detail in e.g. the Final Reports of stage 1 and 2 (SKI Report 95:14 and 96:50). Higher order eigenfunctions and eigenvalues of the diffusion equation, describing a static core, have lost their significance when doing calculations in realistic systems, since there are usually made by nodal methods or other direct numerical techniques. However, there are situations when knowledge of the higher order modes is still useful. Such case is the separation of the global and regional flux oscillations in the case of BWR instability. Another case is the investigation of the stability properties of large inhomogeneous cores, which is usually quantified with the so-called eigenvalue separation, ES=1/k{sub 1} - 1/k{sub 0} where k{sub 0} and k{sub 1}, are the fundamental and first higher order eigenvalues, respectively. Numerical codes used for ICMF calculations usually do not have the option of calculating the higher order eigenvalues and eigenfunctions. In idealised systems, these can be calculated with semi-analytical methods. In order to get insight into the characteristics of the higher order eigenmodes of the neutron flux and the adjoint, these were calculated in a reflected homogeneous system with two-group theory. The adjoint eigenmodes are necessary if an orthogonality property needs to be used, such as the separation of the modes from a flux shape which is a sum of several eigenmodes. At the same time, the so-called numerical noise simulator, developed at the Dept., was extended such that it became suitable for the calculation of the higher order eigenmodes, both direct and adjoint ones. This simulator can treat real inhomogeneous cores, with an input deck compatible with that of SIMULATE. The simulator was used to calculate the

  12. Sensitive Spitzer Photometry of Supermassive Black Holes at the Final Stage of Adolescence

    Science.gov (United States)

    Shemmer, Ohad; Netzer, Hagai; Mor, Rivay; Trakhtenbrot, Benny

    2011-05-01

    We propose to obtain sensitive Spitzer snapshot observations of a unique sample of 35 Sloan Digital Sky Survey quasars at redshift 4.8 for which we obtained reliable, Mg II-based determinations of the supermassive black hole (SMBH) mass and normalized accretion rate (L/L_Edd). These quasars appear to mark the final stage of SMBH `adolescence' in the history of the Universe as their SMBHs are significantly less massive and their L/L_Edd values are significantly higher with respect to their counterparts at lower redshifts. Our observations will provide both 1) deep coverage of the fields around these quasars which will be utilized as crucial priors for our approved Herschel/SPIRE observations of these sources, and 2) coverage of the rest-frame optical SEDs of these fast accreting quasars. The results will maximize our ability to measure the star-formation rate in the host galaxies of these quasars using Herschel. We will thus be able to investigate correlations between SMBH growth and star-forming activity in the early Universe. The Spitzer photometry will also provide invaluable information about the shape of the rest-frame optical continuum in these quasars which will be used to search for extreme disk properties that may be signatures of the remarkably high accretion rates in these sources.

  13. Highly loaded multi-stage fan drive turbine: Performance of final three configurations

    Science.gov (United States)

    Cherry, D. G.; Thomas, M. W.

    1974-01-01

    Results for a three-stage highly loaded fan drive turbine follow-on test program are presented. The effects of combinations of tandem and leaned bladerows on three-stage turbine performance were tested. The three-stage turbine with a tandem stator in stage two exhibited a total-to-total efficiency of approximately 0.887 as compared to 0.886 for the plain blade turbine base case.

  14. 75 FR 32748 - Availability of Testing and Evaluation Report and Intent To Proceed With the Final Stages of...

    Science.gov (United States)

    2010-06-09

    ... of Domain Name System Security Extensions Implementation in the Authoritative Root Zone AGENCY... report and NTIA's intent to proceed with the final stages of DNSSEC deployment in the authoritative root... (ICANN) and VeriSign to deploy DNSSEC at the authoritative root zone of the Internet.\\3\\ Subsequently...

  15. Transient phenomena in the final implosion stage at the PF-1000 facility

    International Nuclear Information System (INIS)

    Gribkov, V.A.; Banaszak, A.; Jakubowski, L.; Sadowski, M.J.; Szydlowski, A.; Bienkowska, B.; Borowiecki, M.; Ivanova-Stanik, I.; Karpinski, L.; Miklaszewski, R.A.; Paduch, M.; Scholz, M.; Tomaszewski, K.; Dubrovsky, A.V.

    2006-12-01

    is equal to 1 MJ so it makes this device one of the few where one can investigate an effect of the 'neutron saturation' phenomenon. It was found about 20 years ago and is still under discussion up to now. During these experiments we concentrated our efforts in an investigation of very fast non-equilibrium phenomena taking place in the final stage of plasma implosion, i.e. namely in the period of time, when neutron pulse is generated

  16. Research and Development Program in Reactor Diagnostics and Monitoring with Neutron Noise Methods. Stage 8. Final report

    International Nuclear Information System (INIS)

    Pazsit, I.; Demaziere, C.; Arzhanov, V.

    2003-01-01

    This report constitutes Stage 8 of a long-term research and development program concerning the development of diagnostics and monitoring methods for nuclear reactors. A brief proposal for the continuation of this program in stage 9 is also given at the end of the report. The program executed in Stage 8 consists of three parts and the work performed in each part is summarized below. In Stage 7, an anomaly localisation algorithm was presented and applied to the Forsmark-1 channel instability event. This investigation was carried out with a set of static data that were typical of a generic BWR model, since no data except the Local Power Range Monitors (LPRMs) time signals recorded during the instability event were made accessible to us at that time. In the present Stage, these static data were obtained from Vattenfall Fuel AB, who used the SIMULATE-3 code. The first Section of this report is thus devoted to this anomaly localisation but this time with a relevant set of data, both regarding the static core conditions and regarding the LPRMs time signals. The noise source pointed out by the localisation algorithm was once again found to be very close to an unseated fuel assembly discovered during the fuel outage following the instability event. The localisation procedure relies in fact on the prior calculation of the reactor transfer function, carried out via the neutron noise simulator first presented in Stage 6 and later improved in Stage 7. The neutron noise simulator was also improved in this Stage. More precisely, a 2-D 2- group static core simulator was developed in order to calculate the static flux and the associated eigenvalue with a spatial discretization scheme compatible with the one in use in the neutron noise simulator, i.e. finite differences. It has generally been assumed that the Decay Ratio (DR), a parameter characterizing the stability of BWRs, is a space-independent parameter of the reactor, i.e. it is independent of which LPRM is used in the core to

  17. Aespoe Hard Rock Laboratory. Final report of the first stage of the tracer retention understanding experiments

    Energy Technology Data Exchange (ETDEWEB)

    Winberg, A. [Conterra AB, Uppsala (Sweden); Andersson, Peter [Geosigma AB, Uppsala (Sweden); Hermanson, Jan [Golder Grundteknik, Solna (Sweden); Byegaard, Johan [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Nuclear Chemistry; Cvetkovic, V. [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Water Resources Engineering; Birgersson, Lars [Kemakta Konsult AB, Stockholm (Sweden)

    2000-03-15

    The first stage of the Tracer Retention Understanding Experiments (TRUE) was performed as a SKB funded project. The overall objectives of TRUE are to develop the understanding of radionuclide migration and retention in fractured rock, to evaluate the realism in applied model concepts, and to assess whether the necessary input data to the models can be collected from site characterisation. Further, to evaluate the usefulness and feasibility of different model approaches, and finally to provide in situ data on radionuclide migration and retention. The strive for address with multiple approaches is facilitated through a close collaboration with the Aespoe Task Force on Modelling of Groundwater Flow and Transport of Solutes. The TRUE programme is a staged programme which addresses various scales from laboratory (< 0.5 m), detailed scale (< 10 m) and block scale (10-50 m). The First TRUE Stage was performed in the detailed scale with the specific objectives of providing data and conceptualising the investigated feature using conservative and sorbing tracers. Further, to improve methodologies for performing tracer tests, and to develop and test a methodology for obtaining pore volume/aperture data from epoxy resin injection, excavation and subsequent analyses. The experimental site is located at approximately 400 m depth in the northeastern part of the Aespoe Hard Rock Laboratory. The identification of conductive fractures and the target feature has benefited from the use of BIPS borehole TV imaging combined with detailed flow logging. The assessment of the conductive geometry has been further sustained by cross-hole pressure interference data. The investigated target feature (Feature A) is a reactivated mylonite which has later undergone brittle deformation. The feature is oriented northwest, along the principal horizontal stress orientation, and is a typical conductor for Aespoe conditions. Hydraulic characterisation shows that the feature is relatively well isolated

  18. Effect of thermal shock on developmental stages of estuarine fish. Final report

    International Nuclear Information System (INIS)

    Dean, J.M.

    1978-12-01

    Physiological data and ecological data show that the few estuarine spawners have a higher thermal tolerance in the embryonic and larval stages than do the freshwater, coastal, or oceanic spawning species. However, since all three groups (freshwater, estuarine, and oceanic spawners) occupy the estuary and coastal waters at different times of the year, knowledge of their physiology and ecology at different developmental or life cycle stages is critical for estuarine management decisions

  19. Final Report on Two-Stage Fast Spectrum Fuel Cycle Options

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Won Sik [Purdue Univ., West Lafayette, IN (United States); Lin, C. S. [Purdue Univ., West Lafayette, IN (United States); Hader, J. S. [Purdue Univ., West Lafayette, IN (United States); Park, T. K. [Purdue Univ., West Lafayette, IN (United States); Deng, P. [Purdue Univ., West Lafayette, IN (United States); Yang, G. [Purdue Univ., West Lafayette, IN (United States); Jung, Y. S. [Purdue Univ., West Lafayette, IN (United States); Kim, T. K. [Argonne National Lab. (ANL), Argonne, IL (United States); Stauff, N. E. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-01-30

    This report presents the performance characteristics of two “two-stage” fast spectrum fuel cycle options proposed to enhance uranium resource utilization and to reduce nuclear waste generation. One is a two-stage fast spectrum fuel cycle option of continuous recycle of plutonium (Pu) in a fast reactor (FR) and subsequent burning of minor actinides (MAs) in an accelerator-driven system (ADS). The first stage is a sodium-cooled FR fuel cycle starting with low-enriched uranium (LEU) fuel; at the equilibrium cycle, the FR is operated using the recovered Pu and natural uranium without supporting LEU. Pu and uranium (U) are co-extracted from the discharged fuel and recycled in the first stage, and the recovered MAs are sent to the second stage. The second stage is a sodium-cooled ADS in which MAs are burned in an inert matrix fuel form. The discharged fuel of ADS is reprocessed, and all the recovered heavy metals (HMs) are recycled into the ADS. The other is a two-stage FR/ADS fuel cycle option with MA targets loaded in the FR. The recovered MAs are not directly sent to ADS, but partially incinerated in the FR in order to reduce the amount of MAs to be sent to the ADS. This is a heterogeneous recycling option of transuranic (TRU) elements

  20. Final Report on the Research Project Ringhals Diagnostics and Monitoring. Stage 4

    International Nuclear Information System (INIS)

    Demaziere, C.; Arzhanov, V.; Karlsson, Joakim K.H.; Pazsit, I.

    1999-01-01

    This report gives an account of the work performed by the Department of Reactor Physics in the frame of a research contract with Ringhals, Vattenfall AB. The contract constitutes Stage 4 of a long-term co-operative research work concerning diagnostics and monitoring of the BWR and PWR units. The work in Stage 4 has been performed between 1 October 1998 and 1 September 1999. In Stage 4 we have worked with four items as follows: 1. Regional modes in R1 stability measurements; 2. Analysis of data from the measurement 980604; 3. Study of the possibility of measuring the moderator temperature coefficient using noise methods. Literature survey and measurement evaluation; 4. Transfer of the method for determining axial control rod elevation. Current situation and progress

  1. Catalytic conversion of light alkanes-proof-of-concept stage -- Phase 6. Final report, February 1--October 31, 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-12-31

    During the course of the first three years of the Cooperative Agreement, the authors uncovered a family of metal perhaloporphyrin complexes which had unprecedented activity for the selective air-oxidation of light alkanes to alcohols. The reactivity of light hydrocarbon substrates with air or oxygen was in the order: isobutane > propane > ethane > methane, in accord with their homolytic bond dissociation energies. Isobutane was so reactive that the proof-of-concept stage of a process for producing tert-butyl alcohol from isobutane was begun (Phase 5). It was proposed that as more active catalytic systems were developed (Phases 4, 6), propane, then ethane and finally methane oxidations will move into this stage (Phases 7 through 9). As of this writing, however, the program has been terminated during the later stages of Phase 5 and 6 so that further work is not anticipated. 72 refs.

  2. Final environmental assessment: TRU waste drum staging building, Technical Area 55, Los Alamos National Laboratory

    International Nuclear Information System (INIS)

    1996-01-01

    Much of the US Department of Energy's (DOE's) research on plutonium metallurgy and plutonium processing is performed at Los Alamos National Laboratory (LANL), in Los Alamos, New Mexico. LANL's main facility for plutonium research is the Plutonium Facility, also referred to as Technical Area 55 (TA-55). The main laboratory building for plutonium work within the Plutonium Facility (TA-55) is the Plutonium Facility Building 4, or PF-4. This Environmental Assessment (EA) analyzes the potential environmental effects that would be expected to occur if DOE were to stage sealed containers of transuranic (TRU) and TRU mixed waste in a support building at the Plutonium Facility (TA-55) that is adjacent to PF-4. At present, the waste containers are staged in the basement of PF-4. The proposed project is to convert an existing support structure (Building 185), a prefabricated metal building on a concrete foundation, and operate it as a temporary staging facility for sealed containers of solid TRU and TRU mixed waste. The TRU and TRU mixed wastes would be contained in sealed 55-gallon drums and standard waste boxes as they await approval to be transported to TA-54. The containers would then be transported to a longer term TRU waste storage area at TA-54. The TRU wastes are generated from plutonium operations carried out in PF-4. The drum staging building would also be used to store and prepare for use new, empty TRU waste containers

  3. Final environmental assessment: TRU waste drum staging building, Technical Area 55, Los Alamos National Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-09

    Much of the US Department of Energy`s (DOE`s) research on plutonium metallurgy and plutonium processing is performed at Los Alamos National Laboratory (LANL), in Los Alamos, New Mexico. LANL`s main facility for plutonium research is the Plutonium Facility, also referred to as Technical Area 55 (TA-55). The main laboratory building for plutonium work within the Plutonium Facility (TA-55) is the Plutonium Facility Building 4, or PF-4. This Environmental Assessment (EA) analyzes the potential environmental effects that would be expected to occur if DOE were to stage sealed containers of transuranic (TRU) and TRU mixed waste in a support building at the Plutonium Facility (TA-55) that is adjacent to PF-4. At present, the waste containers are staged in the basement of PF-4. The proposed project is to convert an existing support structure (Building 185), a prefabricated metal building on a concrete foundation, and operate it as a temporary staging facility for sealed containers of solid TRU and TRU mixed waste. The TRU and TRU mixed wastes would be contained in sealed 55-gallon drums and standard waste boxes as they await approval to be transported to TA-54. The containers would then be transported to a longer term TRU waste storage area at TA-54. The TRU wastes are generated from plutonium operations carried out in PF-4. The drum staging building would also be used to store and prepare for use new, empty TRU waste containers.

  4. The development of pneumoconiosis and its final stages in miners of the Karvina district

    Energy Technology Data Exchange (ETDEWEB)

    Pochmon, O.; Kratochvil, Z.

    1974-01-01

    The authors studied 63 retired miners from the Ostrava- Karvina coal mines who had a complicated form of pneumoco niosis. They had been repeatedly hospitalized in the department for tuberculosis and respiratory diseases, mostly because of a complicated respiratory illness. Under conditions of the Ostrava-Karvina mines, pneumoco niosis develops rapidly in proportion to the dust pollution the miners are exposed to. In the above 63 miners pneumoconiosis was in an advanced stage (type B and C according to the Geneva classification). The disease progressed most rapidly (within 10 years) in the group of drifters. Chronic bronchitis was found in 44% of the patients, lung emphysema in 56%, cor pulmonale in 57% of cases. The gravest complications in retired miners with an advanced stage of pneumoconiosis were exacerbated chronic bronchitis and bronchopneumonia endangering the lives of the patients.

  5. Bunching beam dynamics in final stage of heavy ion fusion driver

    International Nuclear Information System (INIS)

    Kikuchi, T.; Nakajima, M.; Horioka, K.

    2003-01-01

    A bunching beam dynamics in a final buncher of heavy ion fusion accelerator system is studied using a particle-in-cell method. Emittance evolutions are calculated during the longitudinal beam compression. The emittance dilution depends on the bunching process. The space charge oscillations affect the beam dynamics and emittance dilution. (author)

  6. Developing an inventor support service which performs early stage market and manufacturing evaluations. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1991-10-01

    American businesses are learning the difficult high cost lesson of ignoring production and market factors (producibility, unit product cost (UPC), marketability, etc) during the engineering design phase of product development. Studies have shown that the Japanese spend three times as long as Americans in the design feasibility and decision process of new product introductions and one third the amount of time in the implementation of those products. There is a 20 to 1 cost benefit on effort applied in the design phase versus the production phase of the product life cycle. The number one goal of this project was to establish an organization that has, as one of its purposes, the providing of services responsive to the needs of independent inventors. The number two goal was to demonstrate the value of providing marketing and manufacturing counsel at an early stage in the product development process. The first study goal was met by providing the materials and information necessary to establish an evaluation team and an organization to handle such evaluations. The second study goal was met by demonstrating the impact of early market analysis and manufacturing considerations on product design and therefore on the description of the invention for four different inventions. These inventions were selected at various stages of development. Regardless of stage of development, the marketing and manufacturing reviews resulted in significant changes in design and/or market positioning.

  7. Developing an inventor support service which performs early stage market and manufacturing evaluations. [Final Report

    Energy Technology Data Exchange (ETDEWEB)

    1991-10-01

    American businesses are learning the difficult high cost lesson of ignoring production and market factors (producibility, unit product cost (UPC), marketability, etc) during the engineering design phase of product development. Studies have shown that the Japanese spend three times as long as Americans in the design feasibility and decision process of new product introductions and one third the amount of time in the implementation of those products. There is a 20 to 1 cost benefit on effort applied in the design phase versus the production phase of the product life cycle. The number one goal of this project was to establish an organization that has, as one of its purposes, the providing of services responsive to the needs of independent inventors. The number two goal was to demonstrate the value of providing marketing and manufacturing counsel at an early stage in the product development process. The first study goal was met by providing the materials and information necessary to establish an evaluation team and an organization to handle such evaluations. The second study goal was met by demonstrating the impact of early market analysis and manufacturing considerations on product design and therefore on the description of the invention for four different inventions. These inventions were selected at various stages of development. Regardless of stage of development, the marketing and manufacturing reviews resulted in significant changes in design and/or market positioning.

  8. Research and development program in reactor diagnostics and monitoring with neutron noise methods. Stage 7. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Pazsit, I.; Demaziere, C.; Arzhanov, V. [Chalmers Univ. of Technology, Goeteborg (Sweden). Department of Reactor Physics; Garis, N.S. [Swedish Nuclear Power Inspectorate, Stockholm (Sweden)

    2001-08-01

    This report constitutes stage 7 of a long-term research and development program concerning the development of diagnostics and monitoring methods for nuclear reactors. A proposal for the continuation of this program in stage 8 is also given at the end of the report. In stage 6, the basic principles of a 3-D fully coupled neutronic/thermal-hydraulic simulator in the frequency domain were presented. The neutronic model relied on the two-group diffusion approximation, whereas the thermal-hydraulic algorithms relied on the so called 'lumped' model. The key element of this simulator was that only the static data were required which could be obtained from the Studsvik Scandpower CASMO-4/TABLES-3/ SIMULATE-3 code package. The simulator was developed with this underlying idea, which means that the calculation of the static fluxes and the eigenvalue were avoided. Depending on what kind of spatial discretization scheme which is used in the noise simulator to calculate the 'leakage' noise, it is not granted that the system remains critical by using the group constants supplied by SIMULATE. Nevertheless, when the system is critical, the balance equations should be fulfilled in all nodes with respect to the discretization scheme used. In concrete terms, the calculation of the static fluxes and eigenvalue can be avoided if the system is brought back to criticality by modifying the cross-sections so that the balance equations are always fulfilled with the chosen spatial discretization scheme. This approach was used in this study with the finite difference scheme. As pointed out in stage 6, the finite difference scheme is relatively inefficient compared to finite elements or nodal methods, but on the other hand it is rather easy to implement. These two more sophisticated schemes are planned to be investigated at a later stage, but for the time being the simulator relying on the finite difference scheme was improved as much as possible so that a 2-D entirely

  9. Static Analysis Using the Cloud

    Directory of Open Access Journals (Sweden)

    Rahul Kumar

    2016-10-01

    Full Text Available In this paper we describe our experience of using Microsoft Azure cloud computing platform for static analysis. We start by extending Static Driver Verifier to operate in the Microsoft Azure cloud with significant improvements in performance and scalability. We present our results of using SDV on single drivers and driver suites using various configurations of the cloud relative to a local machine. Finally, we describe the Static Module Verifier platform, a highly extensible and configurable platform for static analysis of generic modules, where we have integrated support for verification using a cloud services provider (Microsoft Azure in this case.

  10. Description of the final instar of Trichomalopsis peregrina (Hymenoptera, Pteromalidae), with data and comments on the preimaginal stages

    International Nuclear Information System (INIS)

    Tormos, J.; Asis, J.D.; Frago, E.; Selfa, J.; Pujade-Villar, J.; Guara, M.

    2007-01-01

    The preimaginal stages of T. peregrina are described. The egg displays a sculptured chorion, which is found only on those deposited externally. The immature larvae are characterized by their peculiarities in (a) a setose ring on the thoracic and abdominal segments, (b) an anal notch and (c) size and the sensory structures of the head capsule. The final instar is described and illustrated. Morphological structures of diagnostic value are discussed. The most salient character shown by the mature larva of this species lies in the epistoma, which is complete. (author) [es

  11. Grid-connected integrated community energy system. Phase II, Stage 2, final report. Executive summary

    Energy Technology Data Exchange (ETDEWEB)

    1978-03-22

    The University of Minnesota Grid-ICES was divided into four identifiable programs in order to study the feasibility of each of the parts of the ICES independently. The total program involves cogeneration, fuel conversion, fuel substitution, and energy conservation by system change. This Phase II report substantiates the theory that the Basic Grid ICES is not only energy-effective, but it will become cost effective as unit operating costs adjust to supply and demand in the 1980's. The Basic Program involves the cogeneration of steam and electricity. The University of Minnesota has been following an orderly process of converting its Central Heating Plant from gas-oil to 100% coal since 1973. The first step in the transition is complete. The University is presently 100% on coal, and will begin the second step, the test burning of low Btu Western coal during the spring, summer, and fall, and high Btu Eastern coal during the high thermal winter period. The final step to 100% Western coal is planned to be completed by 1980. In conjunction with the final step a retired Northern States Power generating plant has been purchased and is in the process of being retrofitted for topping the existing plant steam output during the winter months. The Basic Plan of ICES involves the add-on work and expense of installing additional boiler capacity at Southeast Steam and non-condensing electric generating capability. This will permit the simultaneous generation of electricity and heat dependent upon the thermal requirements of the heating and cooling system in University buildings. This volume presents an overview of the Community and the ICES. (MCW)

  12. Caregiver burden in end-of-life care: advanced cancer and final stage of dementia.

    Science.gov (United States)

    Costa-Requena, Gema; Espinosa Val, M Carmen; Cristòfol, Ramon

    2015-06-01

    Considering two advanced illnesses, cancer and end-stage dementia, the aim of this study was to describe the symptoms of caregiver psychological distress and burden. In this cross-sectional study, regression analyses were calculated to explain the influence of psychological distress in caregiver burden. A t test was employed to compare differences between the symptoms of caregiver burden. The percentage of psychological distress was similar between caregivers of cancer patients (77.6%) and caregivers of dementia patients (72.4%). In the regression analysis, cancer caregiver distress accounted for 27.9% of the variance in symptoms of burden, while dementia caregiver distress accounted for 24.4% of the variance in symptoms of burden. No significant differences were revealed when comparing caregiver burden symptoms between caregivers of the two advanced illnesses (t = 0.06; p = 0.94). In end-of-life care for patients with dementia, due to significant levels of caregiver distress and burden symptoms, there is a need to support caregivers in the same way as is done for caregivers of cancer patients.

  13. [Adding value to the care at the final stage of chronic diseases].

    Science.gov (United States)

    Vacas Guerrero, Mercedes

    2014-01-01

    There is a growing number of people with advanced chronic health conditions and with palliative care needs who die without their health and social needs satisfied. This is enough to redefine the traditional models of care in order to focus on the person, rather than on the disease. In these new models, the important role of nursing is unquestionably to promote an approach based on comprehensive care, coordination and continuity, and at a social health level appropriate to respond to the care of patients who require complex long-term care. The nurse contribution in the end stages of chronic conditions must be in the value of care. Taking care of someone is to be concerned about them. And this is related to attitude, commitment and responsibility. In the care of patients who live in a situation of extreme vulnerability, it is possible to help them feel warmth, confident, relieve their suffering, respect their autonomy, and help them them find sense and hope, through daily tasks. With gestures, words and facial expressions that go with this care, it is possible to preserve patient dignity. Copyright © 2013 Elsevier España, S.L. All rights reserved.

  14. FACTORS INFLUENCING THE ACCURACY OF PRE-CONTRACT STAGE ESTIMATION OF FINAL CONTRACT PRICE IN NEW ZEALAND

    Directory of Open Access Journals (Sweden)

    Cong Ji

    2014-12-01

    Full Text Available Establishing and prioritising the factors that may influence the final contract price when responding to a call for tenders is crucial for proper risk analysis and reliable forecasting; it could make or mar the ability to achieve expected profit margin in an era of lump sum fixed price contracts where clients often contest variation claims. In New Zealand, these factors have not been researched; hence estimators rely only on judgement to ‘guess-estimate’ in their price forecasting. This study aimed to fill the knowledge gap by investigating the priority factors. 150 responses from professional members of the New Zealand Institute of Quantity Surveyors were analysed using multi-attribute method. Results showed thirty-seven factors which could influence the final contract price; the three most influential being poor tender documentation, complexity of design & construction, and completeness of project information. Other factors relating to project, client and contractor characteristics, design consultants and tendering conditions, estimating practice and external factors were reported. Concordance analysis indicated high level of agreement amongst survey participants in the rank-ordering of the relative importance of the identified factors. The findings could assist quantity surveyors to prepare more reliable contract price estimates at the pre-contract stage. It would also improve construction-stage cost control.

  15. Design basis for the copper/steel canister. Stage five. Final report

    International Nuclear Information System (INIS)

    Bowyer, W.H.

    1999-05-01

    cause, in electron beam welding. The improvement in creep strength conferred by the phosphorus is valuable, but the evidence that is available suggests that the influence of phosphorus is very complicated. A view is expressed that further work is required to understand the coupling between the effects on creep properties of phosphorus, processing and grain size. The writer is concerned that the problem of low creep ductility may not have been overcome. It has been recognised that the roll forming method is not suitable for serial production and this approach has been abandoned. Two candidate processes are under investigation for tubular production. These are extrusion and a pierce and draw process, which is similar to backward extrusion. Both these methods are more suitable for serial production and there is a reasonable prospect that either may be developed to provide a satisfactory metallurgical structure. A further option under investigation is reduction of the thickness of the overpack from 50 mm to 30 mm. Very good results have been achieved by using an extrusion temperature of 675 deg C and the problem of controlling grain size in the tubular appears to have been overcome. The pierce and draw process has the advantage that it produces a tubular with an integral bottom. The first trial with this process used a processing temperature of 800 deg C. The resulting grain size was very coarse and the draw did not continue to completion. Further trials are planned. A new electron beam welder has been developed to overcome the problems, which have beset the earlier trials. It has been supplied to the SKB pilot plant where commissioning is in progress. An alternative welding process, friction stir welding, is being examined as a candidate for attaching lids. This is potentially a more favourable process than electron beam welding but it is in an early stage of development. Ultrasonic and radiographic test equipment have been developed for examination of lid welds. They have

  16. 39% access time improvement, 11% energy reduction, 32 kbit 1-read/1-write 2-port static random-access memory using two-stage read boost and write-boost after read sensing scheme

    Science.gov (United States)

    Yamamoto, Yasue; Moriwaki, Shinichi; Kawasumi, Atsushi; Miyano, Shinji; Shinohara, Hirofumi

    2016-04-01

    We propose novel circuit techniques for 1 clock (1CLK) 1 read/1 write (1R/1W) 2-port static random-access memories (SRAMs) to improve read access time (tAC) and write margins at low voltages. Two-stage read boost (TSR-BST) and write word line boost (WWL-BST) after the read sensing schemes have been proposed. TSR-BST reduces the worst read bit line (RBL) delay by 61% and RBL amplitude by 10% at V DD = 0.5 V, which improves tAC by 39% and reduces energy dissipation by 11% at V DD = 0.55 V. WWL-BST after read sensing scheme improves minimum operating voltage (V min) by 140 mV. A 32 kbit 1CLK 1R/1W 2-port SRAM with TSR-BST and WWL-BST has been developed using a 40 nm CMOS.

  17. Outbreaks of paralytic poliomyelitis during 1996-2012: the changing epidemiology of a disease in the final stages of eradication.

    Science.gov (United States)

    Mach, Ondrej; Tangermann, Rudolf H; Wassilak, Steve G; Singh, Simarjit; Sutter, Roland W

    2014-11-01

    Despite substantial progress toward eradication of poliomyelitis, the risk of poliomyelitis outbreaks resulting from virus importations into polio-free areas persists. We reviewed the changing epidemiology of outbreaks in the final stages of the eradication initiative. Available literature on outbreaks of poliomyelitis caused by wild polioviruses between 1996 and 2012 was reviewed. During this period, there were 22 outbreaks involving 39 countries. Outbreaks ranged in size from 1 to 1335 cases. These outbreaks caused 4571 cases, representing 21% of all cases reported during this period. Five outbreaks involved multiple countries. In 76% of outbreaks (16/21) with a known age distribution, cases concentrated among children aged poliomyelitis had not occurred for many years. The changing epidemiology, with cases and higher case-fatality ratios among adults, increased the severity of these outbreaks. © The Author 2014. Published by Oxford University Press on behalf of the Infectious Diseases Society of America. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

  18. Statics and mechanics of structures

    CERN Document Server

    Krenk, Steen

    2013-01-01

    The statics and mechanics of structures form a core aspect of civil engineering. This book provides an introduction to the subject, starting from classic hand-calculation types of analysis and gradually advancing to a systematic form suitable for computer implementation. It starts with statically determinate structures in the form of trusses, beams and frames. Instability is discussed in the form of the column problem - both the ideal column and the imperfect column used in actual column design. The theory of statically indeterminate structures is then introduced, and the force and deformation methods are explained and illustrated. An important aspect of the book’s approach is the systematic development of the theory in a form suitable for computer implementation using finite elements. This development is supported by two small computer programs, MiniTruss and MiniFrame, which permit static analysis of trusses and frames, as well as linearized stability analysis. The book’s final section presents related ...

  19. Geochemical stratigraphy and correlation within large igneous provinces: The final preserved stages of the Faroe Islands Basalt Group

    Science.gov (United States)

    Millett, J. M.; Hole, M. J.; Jolley, D. W.; Passey, S. R.

    2017-08-01

    The Faroe Islands Basalt Group (FIBG) comprises a gross stratigraphic thickness of over 6.5 km of dominantly extrusive basaltic facies erupted during the Late Palaeocene to Early Eocene. In this study we present 140 major and trace element analyses from flow by flow field and borehole sample profiles, through the Enni Formation, which comprises the final phase of volcanism preserved on the Faroe Islands. The sample profiles target geographically spaced and overlapping stratigraphic sequences tied relative to a 3D ArcGIS surface for the regionally extensive volcaniclastic Argir Beds marker unit. From these profiles five geochemical groups including one low TiO2 (Low-Ti 1.5 wt%) groups differentiated by Nb, Zr, Y and V variations are identified in conjunction with previous studies. The spatial and stratigraphic distribution of these groups is mapped across the islands and demonstrates a complex inter-digitated flow field evolution. Within the finer scale variations, broad spatial and temporal development trends are identified demonstrating the potential for correlation within the volcanic succession at the local, tens of kilometers scale. Low-Ti lavas formed in association with lithospheric thinning and developed extensive flow fields between the Faroe Islands and East Greenland contemporaneous to the eruption of High-Ti smaller melt fraction lava flows in both locations. The progression of High-Ti lava groups preserved on either side of the developing rift zone is very similar, but is not, however, chronostratigraphic due to multiple inter-digitations of the chemical types. We tentatively suggest that a previously proposed rift-oblique transfer zone between the Faroe Islands and East Greenland enabled non-uniform lithospheric thinning and the preservation of a near-continuous High-Ti melting region between these areas beyond the onset of Low-Ti eruptions which were initially fed from the west. This study highlights the complex nature of late stage flood basalt

  20. Gap flow in axial turbines. Effects on the flow patterns in the final turbine stage and inside the diffusor. Final report

    International Nuclear Information System (INIS)

    Krueckels, J.

    1996-01-01

    A 3D Navier-Stokes method was modified for discretisation of the gap between the tip of the rotor blade and the casing wall by an additional grid block. Flow calculations were carried out using a zoned approach in which the Navier-Stokes equations are solved only in the gap flow region inside the rotor while the Eulerian equations are solved in the other regions, thus reducing the calculation time. The results are compared with experimental data. The interdependence between turbine and diffusor is taken into account so that the pressure distribution at the rotor outlet will be modelled correctly. The distribution of static pressure at the diffusor outlet must be available as an input variable in this method [de

  1. Static multiplicities in heterogeneous azeotropic distillation sequences

    DEFF Research Database (Denmark)

    Esbjerg, Klavs; Andersen, Torben Ravn; Jørgensen, Sten Bay

    1998-01-01

    different static behavior. The method of Petlyuk and Avet'yan (1971), Bekiaris et al. (1993), which assumes infinite reflux and infinite number of stages, is extended to and applied on heterogeneous azeotropic distillation sequences. The predictions are substantiated through simulations. The static sequence...

  2. Statics and Mechanics of Structures

    DEFF Research Database (Denmark)

    Krenk, Steen; Høgsberg, Jan Becker

    The statics and mechanics of structures form a core aspect of civil engineering. This book provides an introduction to the subject, starting from classic hand-calculation types of analysis and gradually advancing to a systematic form suitable for computer implementation. It starts with statically...... of trusses and frames, as well as linearized stability analysis. The book’s final section presents related strength of materials subjects in greater detail; these include stress and strain, failure criteria, and normal and shear stresses in general beam flexure and in beam torsion....

  3. Research and Development Program in Reactor Diagnostics and Monitoring with Neutron Noise Methods. Stage 10. Final Report

    International Nuclear Information System (INIS)

    Demaziere, C.; Pazsit, I.; Sunde, S.; Wright, J.

    2004-12-01

    This report constitutes Stage 10 of a long-term research and development program concerning the development of diagnostics and monitoring methods for nuclear reactors. The program executed in Stage 10 consists of three parts and the work performed in each part is summarized below. A so-called 2-D 2-group neutron noise simulator was previously developed at the Department of Reactor Physics. This simulator is able to calculate the space-dependence of the neutron noise induced by localised or spatially-distributed absorbers of variable strength or by vibrating absorbers. These calculations are performed in the 2-group diffusion approximation and can treat an arbitrary heterogeneous 2-D system. The goal of the present investigation is to use the simulator for unfolding purposes, i.e. to reconstruct the noise source from the detector readings. This task is particularly challenging since the number of detectors available in a commercial PWR can be very low. In this study, five detectors are assumed to be present and evenly distributed in the core. Furthermore, only localised absorbers of variable strength are considered as perturbations. Numerical simulations were first carried out to verify that the space-dependent local and global components of the neutron noise were overwhelmingly large compared to the point-kinetic term of the neutron noise whose spatial structure does not depend on the position of the perturbation. The significance of the space-dependent global component is that its relaxation length is large enough, so that several neutron detectors can monitor it. Therefore, the neutron noise induced at the position of the detectors is itself a function of the position of the perturbation. Unfolding procedures could thus be considered. Prior to performing any unfolding, the type of the noise source has to be determined, since the algorithms developed in this report are based on the assumption of an absorber of variable strength. Such a noise source can also be

  4. Synthetic Medicinal Chemistry in Chagas' Disease: Compounds at The Final Stage of "Hit-To-Lead" Phase.

    Science.gov (United States)

    Cerecetto, Hugo; González, Mercedes

    2010-03-25

    Chagas' disease, or American trypanosomosiasis, has been the most relevant illness produced by protozoa in Latin America. Synthetic medicinal chemistry efforts have provided an extensive number of chemodiverse hits at the "active-to-hit" stage. However, only a more limited number of these have been studied in vivo in models of Chagas' disease. Herein, we survey some of the cantidates able to surpass the "hit-to-lead" stage discussing their limitations or merit to enter in clinical trials in the short term.

  5. Evaporation dynamics of a sessile droplet on glass surfaces with fluoropolymer coatings: focusing on the final stage of thin droplet evaporation.

    Science.gov (United States)

    Gatapova, Elizaveta Ya; Shonina, Anna M; Safonov, Alexey I; Sulyaeva, Veronica S; Kabov, Oleg A

    2018-03-07

    The evaporation dynamics of a water droplet with an initial volume of 2 μl from glass surfaces with fluoropolymer coatings are investigated using the shadow technique and an optical microscope. The droplet profile for a contact angle of less than 5° is constructed using an image-analyzing interference technique, and evaporation dynamics are investigated at the final stage. We coated the glass slides with a thin film of a fluoropolymer by the hot-wire chemical vapor deposition method at different deposition modes depending on the deposition pressure and the temperature of the activating wire. The resulting surfaces have different structures affecting the wetting properties. Droplet evaporation from a constant contact radius mode in the early stage of evaporation was found followed by the mode where both contact angle and contact radius simultaneously vary in time (final stage) regardless of wettability of the coated surfaces. We found that depinning occurs at small contact angles of 2.2-4.7° for all samples, which are smaller than the measured receding contact angles. This is explained by imbibition of the liquid into the developed surface of the "soft" coating that leads to formation of thin droplets completely wetting the surface. The final stage, which is little discussed in the literature, is also recorded. We have singled out a substage where the contact line velocity is abruptly increasing for all coated and uncoated surfaces. The critical droplet height corresponding to the transition to this substage is about 2 μm with R/h = 107. The duration of this substage is the same for all coated and uncoated surfaces. Droplets observed at this substage for all the tested surfaces are axisymmetric. The specific evaporation rate clearly demonstrates an abrupt increase at the final substage of the droplet evaporation. The classical R 2 law is justified for the complete wetting situation where the droplet is disappearing in an axisymmetric manner.

  6. Catalysts and process developments for two-stage liquefaction. Final technical report, October 1, 1989--September 30, 1992

    Energy Technology Data Exchange (ETDEWEB)

    Cronauer, D.C.; Swanson, A.J.; Sajkowski, D.J.

    1992-12-31

    Research in this project centered upon developing and evaluating catalysts and process improvements for coal liquefaction in the two-stage, close-coupled catalytic process. The major results are summarized here and they are described in more detail under each Task. In tasks for coal pretreatment and beneficiation, it was shown for coal handling that drying of both lignite or subbituminous coals using warm air, vacuum oven or exposing to air for long time was detrimental to subsequent liquefaction. Both laboratory and bench-scale beneficiations indicated that in order to achieve increased liquefaction yield for Illinois No. 6 bituminous coal, size separation with in sink-float technique should be used. For subbituminous coal, the best beneficiation was aqueous SO{sub 2} treatment, which reduced mineral matter. In the case of lignite, the fines should be rejected prior to aqueous SO{sub 2} treatment and sink-float gravity separation. In liquefying coals with supported catalysts in both first and second stages, coal conversion was highest (93%) with Illinois No. 6 coal, which also had the highest total liquid yield of 80%, however, the product contained unacceptably high level of resid (30%). Both low rank coals gave lower conversion (85--87%) and liquid yields (57--59%), but lighter products (no resid). The analysis of spent first stage catalysts indicated significant sodium and calcium deposits causing severe deactivation. The second stage catalysts were in better condition showing high surface areas and low coke and metal deposits. The use of dispersed catalyst in the first stage would combat the severe deactivation.

  7. Statics of deformable solids

    CERN Document Server

    Bisplinghoff, Raymond L; Pian, Theodore HH

    2014-01-01

    Profusely illustrated exposition of fundamentals of solid mechanics and principles of mechanics, statics, and simple statically indeterminate systems. Covers strain and stress in three-dimensional solids, elementary elasticity, energy principles in solid continuum, and more. 1965 edition.

  8. A planning comparison of 3-dimensional conformal multiple static field, conformal arc, and volumetric modulated arc therapy for the delivery of stereotactic body radiotherapy for early stage lung cancer

    Energy Technology Data Exchange (ETDEWEB)

    Dickey, Mike [Department of Medical Physics, Cross Cancer Institute, Edmonton, Alberta (Canada); Roa, Wilson; Drodge, Suzanne [Department of Radiation Oncology, Cross Cancer Institute, Edmonton, Alberta (Canada); Ghosh, Sunita [Department of Medical Oncology, Cross Cancer Institute, Edmonton, Alberta (Canada); Murray, Brad [Department of Medical Physics, Cross Cancer Institute, Edmonton, Alberta (Canada); Scrimger, Rufus [Department of Radiation Oncology, Cross Cancer Institute, Edmonton, Alberta (Canada); Gabos, Zsolt, E-mail: zgabos@ualberta.ca [Department of Radiation Oncology, Cross Cancer Institute, Edmonton, Alberta (Canada); Department of Medical Physics, Cross Cancer Institute, Edmonton, Alberta (Canada)

    2015-01-01

    The primary objective of this study was to compare dosimetric variables as well as treatment times of multiple static fields (MSFs), conformal arcs (CAs), and volumetric modulated arc therapy (VMAT) techniques for the treatment of early stage lung cancer using stereotactic body radiotherapy (SBRT). Treatments of 23 patients previously treated with MSF of 48 Gy to 95% of the planning target volume (PTV) in 4 fractions were replanned using CA and VMAT techniques. Dosimetric parameters of the Radiation Therapy Oncology Group (RTOG) 0915 trial were evaluated, along with the van't Riet conformation number (CN), monitor units (MUs), and actual and calculated treatment times. Paired t-tests for noninferiority were used to compare the 3 techniques. CA had significant dosimetric improvements over MSF for the ratio of the prescription isodose volume to PTV (R{sub 100%}, p < 0.0001), the maximum dose 2 cm away from the PTV (D{sub 2} {sub cm}, p = 0.005), and van't Riet CN (p < 0.0001). CA was not statistically inferior to MSF for the 50% prescription isodose volume to PTV (R{sub 50%}, p = 0.05). VMAT was significantly better than CA for R{sub 100%} (p < 0.0001), R{sub 50%} (p < 0.0001), D{sub 2} {sub cm} (p = 0.006), and CN (p < 0.0001). CA plans had significantly shorter treatment times than those of VMAT (p < 0.0001). Both CA and VMAT planning showed significant dosimetric improvements and shorter treatment times over those of MSF. VMAT showed the most favorable dosimetry of all 3 techniques; however, the dosimetric effect of tumor motion was not evaluated. CA plans were significantly faster to treat, and minimize the interplay of tumor motion and dynamic multileaf collimator (MLC) motion effects. Given these results, CA has become the treatment technique of choice at our facility.

  9. Radiologic comparison of posterior release, internal distraction, final PSO and spinal fusion with one-stage posterior vertebral column resection for multi-level severe congenital scoliosis.

    Science.gov (United States)

    Liu, Shichang; Zhang, Nannan; Song, Yueming; Song, Zongrang; Zhang, Liping; Liu, Jijun; Xie, En; Wu, Qining; Hao, Dingjun

    2017-06-20

    To compare radiologic results of posterior release, internal distraction, and final pedicle subtraction osteotomy (PSO) and spinal fusionwith one-stage posterior vertebral column resection (PVCR) in treating multi-level severe congenital scoliosis. Forty-onesevere congenital scoliosis patients were used in the study. Group A comprised 24 patients who underwent one-stage PVCR. Group B comprised 17 patients who underwent posterior release with internal distraction, followed by final posterior fusion and instrumentation. The average preoperative main curve was 110.4° (95-130°) in group A and 109.4° (range 90°-126°) in group B. Postoperative follow-up time was ≥2 years (2.0-4.5 years) to analyze the radiographic and clinical outcomes. A comparison of posterior release, internal distraction, and final spinal fusion with PVCR showed no significant differences in postoperative main curve and compensatory caudal curve correction, coronal and sagittal imbalance. However, significant differences were found between the 2 groups in compensatory cranial curve correction. Posterior release, internal distraction, and final spinal fusion produce better corrective results in compensatory cranial curve correction than PVCR in treating severe multi-level congenital scoliosis.

  10. Marginal Bone Remodeling around healing Abutment vs Final Abutment Placement at Second Stage Implant Surgery: A 12-month Randomized Clinical Trial.

    Science.gov (United States)

    Nader, Nabih; Aboulhosn, Maissa; Berberi, Antoine; Manal, Cordahi; Younes, Ronald

    2016-01-01

    The periimplant bone level has been used as one of the criteria to assess the success of dental implants. It has been documented that the bone supporting two-piece implants undergoes resorption first following the second-stage surgery and later on further to abutment connection and delivery of the final prosthesis. The aim of this multicentric randomized clinical trial was to evaluate the crestal bone resorption around internal connection dental implants using a new surgical protocol that aims to respect the biological distance, relying on the benefit of a friction fit connection abutment (test group) compared with implants receiving conventional healing abutments at second-stage surgery (control group). A total of partially edentulous patients were consecutively treated at two private clinics, with two adjacent two-stage implants. Three months after the first surgery, one of the implants was randomly allocated to the control group and was uncovered using a healing abutment, while the other implant received a standard final abutment and was seated and tightened to 30 Ncm. At each step of the prosthetic try-in, the abutment in the test group was removed and then retightened to 30 Ncm. Horizontal bone changes were assessed using periapical radiographs immediately after implant placement and at 3 (second-stage surgery), 6, 9 and 12 months follow-up examinations. At 12 months follow-up, no implant failure was reported in both groups. In the control group, the mean periimplant bone resorption was 0.249 ± 0.362 at M3, 0.773 ± 0.413 at M6, 0.904 ± 0.36 at M9 and 1.047 ± 0.395 at M12. The test group revealed a statistically significant lower marginal bone loss of 20.88% at M3 (0.197 ± 0.262), 22.25% at M6 (0.601 ± 0.386), 24.23% at M9 (0.685 ± 0.341) and 19.2% at M9 (0.846 ± 0.454). The results revealed that bone loss increased over time, with the greatest change in bone loss occurring between 3 and 6 months. Alveolar bone loss was significantly greater in the

  11. Catalytic Two-Stage Liquefaction (CTSL) process bench studies with bituminous coal. Final report, [October 1, 1988--December 31, 1992

    Energy Technology Data Exchange (ETDEWEB)

    Comolli, A.G.; Johanson, E.S.; Karolkiewicz, W.F.; Lee, L.K.; Stalzer, R.H.; Smith, T.O.

    1993-03-01

    Reported herein are the details and results of Laboratory and Bench-Scale experiments using bituminous coal concluded at Hydrocarbon Research, Inc., under DOE contract during the period October 1, 1988 to December 31, 1992. The work described is primarily concerned with the application of coal cleaning methods and solids separation methods to the Catalytic Two-Stage Liquefaction (CTSL) Process. Additionally a predispersed catalyst was evaluated in a thermal/catalytic configuration, and an alternative nickel molybdenum catalyst was evaluated for the CTSL process. Three coals were evaluated in this program: Bituminous Illinois No. 6 Burning Star and Sub-bituminous Wyoming Black Thunder and New Mexico McKinley Mine seams. The results from a total of 16 bench-scale runs are reported and analyzed in detail. The tests involving the Illinois coal are reported herein, and the tests involving the Wyoming and New Mexico coals are described in Topical Report No. 1. On the laboratory scale, microautoclave tests evaluating coal, start-up oils, catalysts, thermal treatment, CO{sub 2} addition and sulfur compound effects are reported in Topical Report No. 3. Other microautoclave tests, such as tests on rejuvenated catalyst, coker liquids, and cleaned coals, are described in the Bench Run sections to which they refer. The microautoclave tests conducted for modelling the CTSL process are described in the CTSL Modelling section of Topical Report No. 3 under this contract.

  12. Static electromagnetic frequency changers

    CERN Document Server

    Rozhanskii, L L

    1963-01-01

    Static Electromagnetic Frequency Changers is about the theory, design, construction, and applications of static electromagnetic frequency changers, devices that used for multiplication or division of alternating current frequency. It is originally published in the Russian language. This book is organized into five chapters. The first three chapters introduce the readers to the principles of operation, the construction, and the potential applications of static electromagnetic frequency changers and to the principles of their design. The two concluding chapters use some hitherto unpublished work

  13. Evolution of Coextruded Structures in Static Mixers

    Science.gov (United States)

    Sollogoub, C.; Guinault, A.; Pedros, M.

    2007-04-01

    Coextrusion allows to combine two thermoplastics in different ways, creating structures with different cross-sectional geometries (side-by-side structure or concentric ring structure). We use static mixers after the feedblock, in order to homogenise these initial structures and obtain different blend morphologies. The control of these morphologies is of prime importance in order to predict the final properties of the polymer blends. The aim of this paper is to study the evolution of some initial coextruded structures in different static mixers. Different static mixers, with adjustable number of mixing elements, are tested. The experimental observations are confronted with numerical simulation results.

  14. Grid-Connected Integrated Community Energy System. Phase II: detailed feasibility analysis and preliminary design. Final report, Stage 2

    Energy Technology Data Exchange (ETDEWEB)

    1978-11-01

    The purpose of this study was to determine the economic and environmental feasibility of a Grid-Connected Integrated Community Energy System (ICES) based on a multifuel (gas, oil, treated solid wastes, and coal) design with which to serve any or all the institutions within the Louisiana Medical Complex in cooperation with the Health Education Authority of Louisiana (HEAL). In this context, a preliminary design is presented which consists of ICES plant description and engineering analyses. This demonstration system is capable of meeting 1982 system demands by providing 10,000 tons of air conditioning and, from a boiler plant with a high-pressure steam capacity of 200,000 lb/h, approximately 125,000 lb/h of 185 psig steam to the HEAL institutions, and at the same time generating up to 7600 kW of electrical power as byproduct energy. The plant will consist of multiple-fuel steam boilers, turbine generator, turbine driven chillers and necessary auxiliaries and ancillary systems. The preliminary design for these systems and for the building to house the central plant systems are presented along with equipment and instrumentation schedules and outline specifications for major components. Costs were updated to reflect revised data. The final preliminary cost estimate includes allowances for contingencies and escalation, as well as cost for the plant site and professional fees. This design is for a facility specifically with coal burning capability, recognizing that it is more capital-intensive than a gas/oil facility. In the opinion of the Louisiana Department of Natural Resources (DNR), the relatively modest allocations made for scrubbing and ash removal involve less than is implied in standard industry (EPRI) cost increments of over 30% for these duties. The preliminary environmental assessment is included. (LCL)

  15. Medicare program; End-Stage Renal Disease prospective payment system, quality incentive program, and Durable Medical Equipment, Prosthetics, Orthotics, and Supplies. Final rule.

    Science.gov (United States)

    2014-11-06

    This final rule will update and make revisions to the End-Stage Renal Disease (ESRD) prospective payment system (PPS) for calendar year (CY) 2015. This rule also finalizes requirements for the ESRD quality incentive program (QIP), including for payment years (PYs) 2017 and 2018. This rule will also make a technical correction to remove outdated terms and definitions. In addition, this final rule sets forth the methodology for adjusting Durable Medical Equipment, Prosthetics, Orthotics, and Supplies (DMEPOS) fee schedule payment amounts using information from the Medicare DMEPOS Competitive Bidding Program (CBP); makes alternative payment rules for certain DME under the Medicare DMEPOS CBP; clarifies the statutory Medicare hearing aid coverage exclusion and specifies devices not subject to the hearing aid exclusion; will not update the definition of minimal self-adjustment; clarifies the Change of Ownership (CHOW) and provides for an exception to the current requirements; revises the appeal provisions for termination of a CBP contract, including the beneficiary notification requirement under the Medicare DMEPOS CBP, and makes a technical change to the regulation related to the conditions for awarding contracts for furnishing infusion drugs under the Medicare DMEPOS CBP.

  16. Adakite-gabbro-anorthosite magmatism at the final (576-546 Ma) development stage of the Neoproterozoic active margin in the south-west of the Siberian craton

    Science.gov (United States)

    Vernikovskaya, A. E.; Vernikovsky, V. A.; Matushkin, N. Yu.; Kadilnikov, P. I.; Romanova, I. V.; Larionov, A. N.

    2017-12-01

    In the late Neoproterozoic a prolonged active continental margin mode dominated the southwestern margin of the Siberian craton. Based on results of geological, petrological-geochemical, U-Th-Pb and Sm-Nd, Rb-Sr isotope investigations, for the first time we established that on the final evolution stage of this margin 576-546 Ma, intrusions of adakites and gabbro-anorthosites of the Zimoveyniy massif were emplaced in the South Yenisei Ridge. These new data indicate genetic relationships of the studied adakites and host NEB-metabasites. The formation of adakites could have been due to a crustal or a mantle-crustal source in a setting of transform sliding of lithospheric plates after the subduction stopped.

  17. Carbon steel protection in G.S. (Girlder sulfide) heavy water fabrication plants. Control of iron content at the final stage of passivation. Pt. 10

    International Nuclear Information System (INIS)

    Rojo, E.A.

    1991-01-01

    This paper is part of a series which corresponds to the carbon steel behaviour as construction material for Girlder sulfide (G.S.) heavy water plants. The present work analyses the iron concentration study during passivation in the passivating fluid. At the beginning, during the formation of the most soluble sulfide -that is the mackinawite-, the iron concentration reaches more than 10 ppm. After some days, this iron concentration begins to decrease up to its stabilization under 0.1 ppm. This process, which occurs in the 9th. and 11th days, indicates that passivation is over, and that a pyrite and pyrrhotite-pyrite layer exists on the iron. Some differences exist between the results obtained and those previsible for the iron sulfides solubilities. In spite of these difficulties, the procedure is perfectly adequate to judge the passivation final stage. (Author) [es

  18. Static Validation of Security Protocols

    DEFF Research Database (Denmark)

    Bodei, Chiara; Buchholtz, Mikael; Degano, P.

    2005-01-01

    We methodically expand protocol narrations into terms of a process algebra in order to specify some of the checks that need to be made in a protocol. We then apply static analysis technology to develop an automatic validation procedure for protocols. Finally, we demonstrate that these techniques ...... suffice to identify several authentication flaws in symmetric and asymmetric key protocols such as Needham-Schroeder symmetric key, Otway-Rees, Yahalom, Andrew secure RPC, Needham-Schroeder asymmetric key, and Beller-Chang-Yacobi MSR...

  19. Observing the Forces Involved in Static Friction under Static Situations

    Science.gov (United States)

    Kaplan, Daniel

    2013-01-01

    Static friction is an important concept in introductory physics. Later in the year students apply their understanding of static friction under more complex conditions of static equilibrium. Traditional lab demonstrations in this case involve exceeding of the maximum level of static friction, resulting in the "onset of motion." (Contains…

  20. 78 FR 35645 - Certain Static Random Access Memories and Products Containing Same; Commission Determination...

    Science.gov (United States)

    2013-06-13

    ... INTERNATIONAL TRADE COMMISSION [Investigation No. 337-TA-792] Certain Static Random Access Memories and Products Containing Same; Commission Determination Affirming a Final Initial Determination..., and the sale within the United States after importation of certain static random access memories and...

  1. Energy conversion statics

    CERN Document Server

    Messerle, H K; Declaris, Nicholas

    2013-01-01

    Energy Conversion Statics deals with equilibrium situations and processes linking equilibrium states. A development of the basic theory of energy conversion statics and its applications is presented. In the applications the emphasis is on processes involving electrical energy. The text commences by introducing the general concept of energy with a survey of primary and secondary energy forms, their availability, and use. The second chapter presents the basic laws of energy conversion. Four postulates defining the overall range of applicability of the general theory are set out, demonstrating th

  2. Static Transition Compression

    DEFF Research Database (Denmark)

    Damian, Daniel; Danvy, Olivier

    2001-01-01

    Starting from an operational specification of a translation from a structured to an unstructured imperative language, we point out how a compositional and context-insensitive translation gives rise to static chains of jumps. Taking an inspiration from the notion of continuation, we state a new...... compositional and context-sensitive specification that provably gives rise to no static chains of jumps, no redundant labels, and no unused labels. It is defined with one inference rule per syntactic construct and operates in linear time and space on the size of the source program (indeed it operates in one...

  3. Static analysis for blinding

    DEFF Research Database (Denmark)

    Nielsen, Christoffer Rosenkilde; Nielson, Hanne Riis

    2006-01-01

    operation blinding. In this paper we study the theoretical foundations for one of the successful approaches to validating cryptographic protocols and we extend it to handle the blinding primitive. Our static analysis approach is based on Flow Logic; this gives us a clean separation between the specification...

  4. Static Transition Compression

    DEFF Research Database (Denmark)

    Danvy, Olivier; Damian, Daniel

    2001-01-01

    Starting from an operational specification of a translation from a structured to an unstructured imperative language, we point out how a compositional and context-insensitive translation gives rise to static chains of jumps. Taking an inspiration from the notion of continuation, we state a new co...

  5. Why Static Clings

    Science.gov (United States)

    Naab, Laurie; Henry, David

    2009-01-01

    Using Wiggins and McTighe's (1998) concept of Big Ideas, the authors planned and designed an electricity investigation to address common student misconceptions about static electricity. With Styrofoam plates and transparent tape, elementary students investigated many properties of electrically charged and uncharged objects in a 5E learning cycle…

  6. Explosions and static electricity

    DEFF Research Database (Denmark)

    Jonassen, Niels M

    1995-01-01

    The paper deals with the problem of electrostatic discharges as causes of ignition of vapor/gas and dust/gas mixtures. A series of examples of static-caused explosions will be discussed. The concepts of explosion limits, the incendiveness of various discharge types and safe voltages are explained...

  7. Close-coupled Catalytic Two-Stage Liquefaction (CTSL{trademark}) process bench studies. Final report, [October 1, 1988--July 31, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Comolli, A.G.; Johanson, E.S.; Karolkiewicz, W.F.; Lee, L.K.; Popper, G.A.; Stalzer, R.H.; Smith, T.O.

    1993-06-01

    This is the final report of a four year and ten month contract starting on October 1, 1988 to July 31, 1993 with the US Department of Energy to study and improve Close-Coupled Catalytic Two-Stage Direct Liquefaction of coal by producing high yields of distillate with improved quality at lower capital and production costs in comparison to existing technologies. Laboratory, Bench and PDU scale studies on sub-bituminous and bituminous coals are summarized and referenced in this volume. Details are presented in the three topical reports of this contract; CTSL Process Bench Studies and PDU Scale-Up with Sub-Bituminous Coal-DE-88818-TOP-1, CTSL Process Bench Studies with Bituminous Coal-DE-88818-TOP-2, and CTSL Process Laboratory Scale Studies, Modelling and Technical Assessment-DE-88818-TOP-3. Results are summarized on experiments and studies covering several process configurations, cleaned coals, solid separation methods, additives and catalysts both dispersed and supported. Laboratory microautoclave scale experiments, economic analysis and modelling studies are also included along with the PDU-Scale-Up of the CTSL processing of sub-bituminous Black Thunder Mine Wyoming coal. During this DOE/HRI effort, high distillate yields were maintained at higher throughput rates while quality was markedly improved using on-line hydrotreating and cleaned coals. Solid separations options of filtration and delayed coking were evaluated on a Bench-Scale with filtration successfully scaled to a PDU demonstration. Directions for future direct coal liquefaction related work are outlined herein based on the results from this and previous programs.

  8. Static and dynamic stresses

    DEFF Research Database (Denmark)

    Tishin, A.M.; Spichkin, Yu.I.; Bohr, Jakob

    1999-01-01

    to the appearance of anomalies in elastic constants, as well as to additional damping of sound oscillations in the lanthanide materials. The importance of understanding the nature of magnetoelastic interactions and related effects arises from the scientific desire to gather a better knowledge of magnetism, as well......In this chapter we shall consider the properties of lanthanide metals, their alloys and compounds which can be studied using static and alternating mechanical stresses. The main attention will be paid to the effects related to magnetoelastic interactions. These interactions in magnetic materials...... can display themselves in static magnetostriction deformations (this effect is not considered here) and in the changing of the magnetic state under mechanical stress. The latter causes variation of the magnetic phase transition temperatures, magnetization and magnetic structures, and leads...

  9. Assessing Static Performance of the Dashengguan Yangtze Bridge by Monitoring the Correlation between Temperature Field and Its Static Strains

    Directory of Open Access Journals (Sweden)

    Gao-Xin Wang

    2015-01-01

    Full Text Available Taking advantage of the structural health monitoring system installed on the steel truss arch girder of Dashengguan Yangtze Bridge, the temperature field data and static strain data are collected and analyzed for the static performance assessment of the bridge. Through analysis, it is found that the static strain changes are mainly caused by temperature field (temperature and temperature difference and train. After the train-induced static strains are removed, the correlation between the remaining static strains and the temperature field shows apparent linear characteristics, which can be mathematically modeled for the description of static performance. Therefore, multivariate linear regression function combined with principal component analysis is introduced to mathematically model the correlation. Furthermore, the residual static strains of mathematical model are adopted as assessment indicator and three kinds of degradation regulations of static performance are obtained after simulation of the residual static strains. Finally, it is concluded that the static performance of Dashengguan Yangtze Bridge was in a good condition during that period.

  10. Axial static mixer

    Science.gov (United States)

    Sandrock, H.E.

    1982-05-06

    Static axial mixing apparatus includes a plurality of channels, forming flow paths of different dimensions. The axial mixer includes a flow adjusting device for adjustable selective control of flow resistance of various flow paths in order to provide substantially identical flows through the various channels, thereby reducing nonuniform coating of interior surfaces of the channels. The flow adjusting device may include diaphragm valves, and may further include a pressure regulating system therefor.

  11. Static electromagnetic field

    International Nuclear Information System (INIS)

    Accioly, A.J.; Vaidya, A.N.; Som, M.M.

    1983-01-01

    The problem of static electromagnetic field admitting a time-like and two space-like Killing vectors is completely solved. The solutions contain plane-symmetric solution as a special case. The solutions can be transformed into solutions describing the gravitational field of a charge line-mass by suitably introducing weyl's canonical coordinates. Further, these solutions are true generalizations of Kasner solutions. (Author) [pt

  12. Microprocessor controlled static converter

    Directory of Open Access Journals (Sweden)

    Stefan Szabo

    2005-10-01

    Full Text Available This paper wants to demonstrate a way of implementing a microcontroller into an DC motor speed control loop. The static power converter is a fully controlled rectifier bridge, using standard SCR's. The bridge's control signals are supplied by the microcontroller and are phase-angle or burst types. The automation loop contains a software PI-style regulator. All the experimental results shows that this aproach is flexibile enough to be used on a large scale.

  13. Static strain aging in austenitic stainless steels

    International Nuclear Information System (INIS)

    Monteiro, S.N.

    1978-07-01

    The static strain aging effects were investigated in austenitic stainless steels by measuring the yield points developed in tensile tests following the arrest of the crosshead for some period of time. The results appear to indicate that the dragging of dislocations in the interval of temperatures from 100 to 300 0 C, where the strain aging is effective, does not apparently depend on the Cottrell's atmosphere. Moreover the influence of the pre-deformation and time on the yield point intensity displayed the existence of stages. The strain aging mechanics and the reasons for the stages were discussed. (Author) [pt

  14. PEBBLES Simulation of Static Friction and New Static Friction Benchmark

    International Nuclear Information System (INIS)

    Cogliati, Joshua J.; Ougouag, Abderrafi M.

    2010-01-01

    Pebble bed reactors contain large numbers of spherical fuel elements arranged randomly. Determining the motion and location of these fuel elements is required for calculating certain parameters of pebble bed reactor operation. This paper documents the PEBBLES static friction model. This model uses a three dimensional differential static friction approximation extended from the two dimensional Cundall and Strack model. The derivation of determining the rotational transformation of pebble to pebble static friction force is provided. A new implementation for a differential rotation method for pebble to container static friction force has been created. Previous published methods are insufficient for pebble bed reactor geometries. A new analytical static friction benchmark is documented that can be used to verify key static friction simulation parameters. This benchmark is based on determining the exact pebble to pebble and pebble to container static friction coefficients required to maintain a stable five sphere pyramid.

  15. Acciones finales discriminantes de voleibol en categorías de formación masculina: importancia del saque en los partidos igualados. (Discriminatory volleyball final actions in male formative stages: importance .

    Directory of Open Access Journals (Sweden)

    Carlos Dávila-Romero

    2012-04-01

    Full Text Available Resumen El objetivo principal del presente estudio fue constatar la importancia del saque en categorías de formación en voleibol masculina y determinar qué otras acciones son relevantes para la victoria en el quinto set de los partidos igualados. Se recogieron un total de 218 partidos (102 en categoría infantil y 116 en categoría cadete, 755 sets (354 en categoría infantil y 401 en categoría cadete y 744 jugadores (360 en categoría infantil y 384 en categoría cadete de los Campeonatos de España de Voleibol de Valladolid 2008 y Huelva 2009 (España en edad escolar masculino (12-16 años. Finalmente se analizaron sólo el quinto set de los partidos igualados. Los resultados del análisis discriminante, mostraron como el saque positivo en ambas categorías, el error en categoría infantil y el ataque positivo en categoría cadete predicen la victoria y/o derrota en el quinto set. Estos sugieren que en momentos decisivos de set y en ambas categorías, el acierto en las acciones ofensivas y el control del patrón técnico del saque es fundamental en estos partidos igualados.AbstractThe aim of this study was to confirm the importance of the serve on formatives stages male volleyball and determine what actions are relevant to the victory in the fifth set on equal matches. We collected a total of 218 matches (102 and 116 in infantile and cadet categories, 755 sets (354 and 401 in infantile and cadet categories and 744 players (360 and 384 in infantile and cadet categories of the Spain Volleyball Championships held in Huelva and Valladolid in 2008 and 2009 (Spain at school-age (12-16 years. Finally were analyzed only the fifth set of equal matches. The results of the discriminant analysis showed how the positive serve in both categories, the error in infantile category and in cadet positive attack may predict victory and / or defeat in the fifth set. They suggest that, in both categories, the success in offensive actions and control of the

  16. The Effect of Static Stretching in Agility and Isokinetic Force at Football Players

    Directory of Open Access Journals (Sweden)

    Sami Sermaxhaj

    2017-10-01

    Full Text Available Cool Down is very important for the recuperation of a football player. The objective of this research is to prove the effect of recuperation with static stretching in agility and isokinetic force at the young football players. This research has taken place between August and November 2015 with a sample of 24 football players of age 15.6±0.4 years, divided in the control group and the experimental group. At first measurements have been initialed body weight 61.1±0.4 kg and body height 175.7±6.4 cm, and agility (20 m zig-zag with and without ball and isokinetic force (peak torque flexion and extension. Both groups of the football players have completed the regular training program. The experimental group (despite the control group during the stage of recuperation (cool down, except the running with slow pace did also carry out the experimental program which did take place through static stretching. Experimental program consisted of 17 exercises bodily static stretching which are applied in the final training session (cool-down. After the experimental phase is finished the participants did undergo the final measures. The conducted results with univariate analysis of variance (ANOVA in two tests (initial and final have shown unimportant statistical values between the control group and the experimental one in the isokinetic force and agility. From the collected results we can conclude the recuperation with static stretching during the cool down has an unimportant statistical impact in the agility and isokinetic force of the young football players.

  17. The Static Baryon Potential

    CERN Document Server

    Alexandrou, C; Tsapalis, A; Forcrand, Ph. de

    2002-01-01

    Using state of the art lattice techniques we investigate the static baryon potential. We employ the multi-hit procedure for the time links and a variational approach to determine the ground state with sufficient accuracy that, for distances up to $\\sim 1.2$ fm, we can distinguish the $Y$- and $\\Delta$- Ans\\"atze for the baryonic Wilson area law. Our analysis shows that the $\\Delta$-Ansatz is favoured. This result is also supported by the gauge-invariant nucleon wave function which we measure for the first time.

  18. On the relationship between ontogenetic and static allometry

    OpenAIRE

    Pelabon, Christophe; Bolstad, Geir Hysing; Egset, Camilla Kalvatn; Cheverud, James M.; Pavlicev, Mihaela; Rosenqvist, Gunilla

    2013-01-01

    Ontogenetic and static allometries describe how a character changes in size when the size of the organism changes during ontogeny and among individuals measured at the same developmental stage, respectively. Understanding the relationship between these two types of allometry is crucial to understanding the evolution of allometry and, more generally, the evolution of shape. However, the effects of ontogenetic allometry on static allometry remain largely unexplored. Here, we first show analytic...

  19. Large scale collective modeling the final 'freeze out' stages of energetic heavy ion reactions and calculation of single particle measurables from these models

    International Nuclear Information System (INIS)

    Nyiri, Agnes

    2005-01-01

    The goal of this PhD project was to develop the already existing, but far not complete Multi Module Model, specially focusing on the last module which describes the final stages of a heavy ion collision, as this module was still missing. The major original achievements summarized in this thesis correspond to the freeze out problem and calculation of an important measurable, the anisotropic flow. Summary of results: Freeze out: The importance of freeze out models is that they allow the evaluation of observables, which then can be compared to the experimental results. Therefore, it is crucial to find a realistic freeze out description, which is proved to be a non-trivial task. Recently, several kinetic freeze out models have been developed. Based on the earlier results, we have introduced new ideas and improved models, which may contribute to a more realistic description of the freeze out process. We have investigated the applicability of the Boltzmann Transport Equation (BTE) to describe dynamical freeze out. We have introduced the so-called Modified Boltzmann Transport Equation, which has a form very similar to that of the BTE, but takes into account those characteristics of the FO process which the BTE can not handle, e.g. the rapid change of the phase-space distribution function in the direction normal to the finite FO layer. We have shown that the main features of earlier ad hoc kinetic FO models can be obtained from BTE and MBTE. We have discussed the qualitative differences between the two approaches and presented some quantitative comparison as well. Since the introduced modification of the BTE makes it very difficult to solve the FO problem from the first principles, it is important to work out simplified phenomenological models, which can explain the basic features of the FO process. We have built and discussed such a model. Flow analysis: The other main subject of this thesis has been the collective flow in heavy ion collisions. Collective flow from ultra

  20. Large scale collective modeling the final 'freeze out' stages of energetic heavy ion reactions and calculation of single particle measurables from these models

    Energy Technology Data Exchange (ETDEWEB)

    Nyiri, Agnes

    2005-07-01

    The goal of this PhD project was to develop the already existing, but far not complete Multi Module Model, specially focusing on the last module which describes the final stages of a heavy ion collision, as this module was still missing. The major original achievements summarized in this thesis correspond to the freeze out problem and calculation of an important measurable, the anisotropic flow. Summary of results: Freeze out: The importance of freeze out models is that they allow the evaluation of observables, which then can be compared to the experimental results. Therefore, it is crucial to find a realistic freeze out description, which is proved to be a non-trivial task. Recently, several kinetic freeze out models have been developed. Based on the earlier results, we have introduced new ideas and improved models, which may contribute to a more realistic description of the freeze out process. We have investigated the applicability of the Boltzmann Transport Equation (BTE) to describe dynamical freeze out. We have introduced the so-called Modified Boltzmann Transport Equation, which has a form very similar to that of the BTE, but takes into account those characteristics of the FO process which the BTE can not handle, e.g. the rapid change of the phase-space distribution function in the direction normal to the finite FO layer. We have shown that the main features of earlier ad hoc kinetic FO models can be obtained from BTE and MBTE. We have discussed the qualitative differences between the two approaches and presented some quantitative comparison as well. Since the introduced modification of the BTE makes it very difficult to solve the FO problem from the first principles, it is important to work out simplified phenomenological models, which can explain the basic features of the FO process. We have built and discussed such a model. Flow analysis: The other main subject of this thesis has been the collective flow in heavy ion collisions. Collective flow from ultra

  1. On the relationship between ontogenetic and static allometry.

    Science.gov (United States)

    Pélabon, Christophe; Bolstad, Geir H; Egset, Camilla K; Cheverud, James M; Pavlicev, Mihaela; Rosenqvist, Gunilla

    2013-02-01

    Ontogenetic and static allometries describe how a character changes in size when the size of the organism changes during ontogeny and among individuals measured at the same developmental stage, respectively. Understanding the relationship between these two types of allometry is crucial to understanding the evolution of allometry and, more generally, the evolution of shape. However, the effects of ontogenetic allometry on static allometry remain largely unexplored. Here, we first show analytically how individual variation in ontogenetic allometry and body size affect static allometry. Using two longitudinal data sets on ontogenetic and static allometry, we then estimate variances and covariances for the different parameters of the ontogenetic allometry defined in our model and assess their relative contribution to the static allometric slope. The mean ontogenetic allometry is the main parameter that determines the static allometric slope, while the covariance between the ontogenetic allometric slope and body size generates most of the discrepancies between ontogenetic and static allometry. These results suggest that the apparent evolutionary stasis of the static allometric slope is not generated by internal (developmental) constraints but more likely results from external constraints imposed by selection.

  2. LAMINAR MIXING IN SMX STATIC MIXERS

    Directory of Open Access Journals (Sweden)

    MUSHTAK AL-ATABI

    2007-04-01

    Full Text Available This paper experimentally examines the performance of a commercial static mixer (SMX. Experiments were carried out to obtain the pressure drop across different numbers of mixing elements (4, 8, 12 and 16. The quality of mixing was visually assessed using flow visualization techniques. Experiments were performed for Reynolds number between 50 and 3000 (based on the unobstructed pipe diameter. The presence of the mixing elements in the flow stream promotes a non-laminar, turbulent-like flow which considerably enhances the mixing. Addition of more mixing elements triggered mixing in the flow at lower Reynolds numbers but this was achieved at the expense of higher pressure drop. This work represents the first stage of an on going work to develop correlations to assess the mixing quality and pressure loss in the SMX static mixers.

  3. Static electricity: A literature review

    Science.gov (United States)

    Crow, Rita M.

    1991-11-01

    The major concern with static electricity is its discharging in a flammable atmosphere which can explode and cause a fire. Textile materials can have their electrical resistivity decreased by the addition of antistatic finishes, imbedding conductive particles into the fibres or by adding metal fibers to the yarns. The test methods used in the studies of static electricity include measuring the static properties of materials, of clothed persons, and of the ignition energy of flammable gases. Surveys have shown that there is sparse evidence for fires definitively being caused by static electricity. However, the 'worst-case' philosophy has been adopted and a static electricity safety code is described, including correct grounding procedures and the wearing of anti-static clothing and footwear.

  4. Static Validation of XSL Transformations

    DEFF Research Database (Denmark)

    Møller, Anders; Olesen, Mads Østerby; Schwartzbach, Michael Ignatieff

    2007-01-01

    no static guarantees that, under the assumption that the input is valid relative to the input schema, the output of the transformation is valid relative to the output schema. We present a validation technique for XSLT based on the XML graph formalism introduced in the static analysis of JWIG Web services...... and XACT XML transformations. Being able to provide static guarantees, we can detect a large class of errors in an XSLT stylesheet at the time it is written instead of later when it has been deployed, and thereby provide benefits similar to those of static type checkers for modern programming languages...

  5. A Succinct Approach to Static Analysis and Model Checking

    DEFF Research Database (Denmark)

    Filipiuk, Piotr

    In a number of areas software correctness is crucial, therefore it is often desirable to formally verify the presence of various properties or the absence of errors. This thesis presents a framework for concisely expressing static analysis and model checking problems. The framework facilitates...... in the classical formulation of ALFP logic. Finally, we show that the logics and the associated solvers can be used for rapid prototyping. We illustrate that by a variety of case studies from static analysis and model checking....

  6. Static traversable wormholes in Lyra manifold

    Science.gov (United States)

    Jahromi, A. Sayahian; Moradpour, H.

    At first, considering the Einstein framework, we introduce some new static traversable wormholes and study the effects of a dark energy-like source on them. Thereinafter, a brief review on Einstein field equations in Lyra manifold is presented, and we address some static traversable wormholes in the Lyra manifold which satisfy the energy conditions. It is also shown that solutions introduced in the Einstein framework may also meet the energy conditions in the Lyra manifold. Finally, we focus on vacuum Lyra manifold and find some traversable asymptotically flat wormholes. In summary, our study shows that it is theoretically possible to find a Lyra displacement vector field in a manner in which traversable wormholes satisfy the energy conditions in a Lyra manifold.

  7. Statics and Mechanics of Structures

    DEFF Research Database (Denmark)

    Krenk, Steen; Høgsberg, Jan Becker

    The statics and mechanics of structures form a core aspect of civil engineering. This book provides an introduction to the subject, starting from classic hand-calculation types of analysis and gradually advancing to a systematic form suitable for computer implementation. It starts with statically...

  8. Superconductor in a weak static gravitational field

    Energy Technology Data Exchange (ETDEWEB)

    Ummarino, Giovanni Alberto [Dipartimento DISAT, Politecnico di Torino, Turin (Italy); National Research Nuclear University MEPhI-Moscow Engineering Physics Institute, Moscow (Russian Federation); Gallerati, Antonio [Dipartimento DISAT, Politecnico di Torino, Turin (Italy)

    2017-08-15

    We provide the detailed calculation of a general form for Maxwell and London equations that takes into account gravitational corrections in linear approximation. We determine the possible alteration of a static gravitational field in a superconductor making use of the time-dependent Ginzburg-Landau equations, providing also an analytic solution in the weak field condition. Finally, we compare the behavior of a high-T{sub c} superconductor with a classical low-T{sub c} superconductor, analyzing the values of the parameters that can enhance the reduction of the gravitational field. (orig.)

  9. Slinky Mechanics: Static Shapes and Unstable States

    Science.gov (United States)

    Holmes, Douglas; Borum, Andy; Moore, Billy; Plaut, Raymond; Dillard, David

    2014-03-01

    The floppy nature of a tumbling Slinky has captivated children and adults alike for over half a century. Highly flexible, the spring will walk down stairs, turn over in your hands, and-much to the chagrin of children everywhere-become easily entangled. The Slinky is an educational tool for demonstrating standing waves, and a structural inspiration due to its ability to extend to many times beyond its initial length without imparting plastic strain on the material. In this work, we provide a mechanical model that captures the static equilibrium configurations of the Slinky in terms of its geometric and material properties. We present both continuous and discrete models to capture a Slinky's static equilibria and unstable transitions. We compare these with experimental results obtained for the Slinky's static equilibrium shapes. We emphasize the importance of modeling coil contact, and determine the critical criteria for the Slinky to topple over in terms of a tilt angle, and the vertical displacement of one bale of coils. Finally, we provide a general description of highly flexible helical springs by considering the nondimensional potential energy of the spring, which characterizes the ``Slinkiness'' of a spring.

  10. Catalytic Two-Stage Liquefaction (CTSL{trademark}) process bench studies and PDU scale-up with sub-bituminous coal. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Comolli, A.G.; Johanson, E.S.; Karolkiewicz, W.F.; Lee, L.K.T.; Stalzer, R.H.; Smith, T.O.

    1993-03-01

    Reported are the details and results of Laboratory and Bench-Scale experiments using sub-bituminous coal conducted at Hydrocarbon Research, Inc., under DOE Contract No. DE-AC22-88PC88818 during the period October 1, 1988 to December 31, 1992. The work described is primarily concerned with testing of the baseline Catalytic Two-Stage Liquefaction (CTSL{trademark}) process with comparisons with other two stage process configurations, catalyst evaluations and unit operations such as solid separation, pretreatments, on-line hydrotreating, and an examination of new concepts. In the overall program, three coals were evaluated, bituminous Illinois No. 6, Burning Star and sub-bituminous Wyoming Black Thunder and New Mexico McKinley Mine seams. The results from a total of 16 bench-scale runs are reported and analyzed in detail. The runs (experiments) concern process variables, variable reactor volumes, catalysts (both supported, dispersed and rejuvenated), coal cleaned by agglomeration, hot slurry treatments, reactor sequence, on-line hydrotreating, dispersed catalyst with pretreatment reactors and CO{sub 2}/coal effects. The tests involving the Wyoming and New Mexico Coals are reported herein, and the tests involving the Illinois coal are described in Topical Report No. 2. On a laboratory scale, microautoclave tests evaluating coal, start-up oils, catalysts, thermal treatment, CO{sub 2} addition and sulfur compound effects were conducted and reported in Topical Report No. 3. Other microautoclave tests are described in the Bench Run sections to which they refer such as: rejuvenated catalyst, coker liquids and cleaned coals. The microautoclave tests conducted for modelling the CTSL{trademark} process are described in the CTSL{trademark} Modelling section of Topical Report No. 3 under this contract.

  11. Pollen performance, cell number, and physiological state in the early-divergent angiosperm Annona cherimola Mill. (Annonaceae) are related to environmental conditions during the final stages of pollen development.

    Science.gov (United States)

    Lora, J; Herrero, M; Hormaza, J I

    2012-09-01

    Pollen performance is an important determinant for fertilization success, but high variability in pollen behavior both between and within species occurs in different years and under varying environmental conditions. Annona cherimola, an early-divergent angiosperm, is a species that releases a variable ratio of bicellular and tricellular hydrated pollen at anther dehiscence depending on temperature. The presence of both bi- and tricellular types of pollen is an uncommon characteristic in angiosperms and makes Annona cherimola an interesting model to study the effect of varying environmental conditions on subsequent pollen performance during the final stages of pollen development. In this work, we study the influence of changes in temperature and humidity during the final stages of pollen development on subsequent pollen performance, evaluating pollen germination, presence of carbohydrates, number of nuclei, and water content. At 25 °C, which is the average field temperature during the flowering period of this species, pollen had a viability of 60-70 %, starch hydrolyzed just prior to shedding, and pollen mitosis II was taking place, resulting in a mixture of bi- and tricellular pollen. This activity may be related to the pollen retaining 70 % water content at shedding. Temperatures above 30 °C resulted in a decrease in pollen germination, whereas lower temperatures did not have a clear influence on pollen germination, although they did have a clear effect on starch hydrolysis. On the other hand, slightly higher dehydration accelerated mitosis II, whereas strong dehydration arrested starch hydrolysis and reduced pollen germination. These results show a significant influence of environmental conditions on myriad pollen characteristics during the final stages of pollen development modifying subsequent pollen behavior and contributing to our understanding of the variability observed in pollen tube performance.

  12. Statics of Historic Masonry Constructions

    CERN Document Server

    Como, Mario

    2013-01-01

    Masonry constructions are the great majority of the buildings in Europe’s historic centres and the most important monuments in its architectural heritage. Given the age of much of these constructions, the demand for safety assessments and restoration projects is pressing and constant. This book aims to help fill this demand presenting a comprehensive new statics of masonry constructions. The book, result of thirty years of research and professional experience, gives the fundamentals of statics of the masonry solid, then applied to the study of statics of arches, piers and vaults. Further, combining engineering and architecture and through an interdisciplinary approach, the book investigates the statical behaviour of many historic monuments, as the Pantheon, the Colosseum,  the domes of S. Maria del Fiore in Florence and of St. Peter in Rome, the Tower of Pisa, the Gothic Cathedrals and the Masonry Buildings under seismic actions.

  13. Demonstration of oxygen-enriched air staging at Owens-Brockway glass containers. Final technical report for the period April 1, 1995--February 28, 1997

    Energy Technology Data Exchange (ETDEWEB)

    Rue, D.; Abbasi, H.

    1997-10-01

    The overall objective of this program was to demonstrate the use of a previously developed combustion modification technology to reduce NO{sub x} emissions from sideport regenerative container glass melters. Specific objectives were to: acquire baseline operating data on the host sideport furnace, evaluate secondary oxidant injection strategies based on earlier endport furnace results and through modeling of a single port pair, retrofit and test one port pair (the test furnace has six port pairs) with a flexible OEAS system, and select the optimal system configuration, use the results from tests with one port pair to design, retrofit, and test OEAS on the entire furnace (six port pairs), and analyze test results, prepare report, and finalize the business plan to commercialize OEAS for sideport furnaces.

  14. Static and Dynamic Traversable Wormholes

    Science.gov (United States)

    Adamiak, Jaroslaw P.

    2008-09-01

    The aim of this work is to discuss the effects found in static and dynamic wormholes that occur as a solution of Einstein equations in general relativity. The ground is prepared by presentation of faster than light effects, then the focus is narrowed to Morris-Thorne framework for a static spherically symmetric wormhole. Two types of dynamic worm-holes, evolving and rotating, are considered.

  15. Static Decoupling in fault detection

    DEFF Research Database (Denmark)

    Niemann, Hans Henrik

    1998-01-01

    An algebraic approach is given for a design of a static residual weighting factor in connection with fault detection. A complete parameterization is given of the weighting factor which will minimize a given performance index......An algebraic approach is given for a design of a static residual weighting factor in connection with fault detection. A complete parameterization is given of the weighting factor which will minimize a given performance index...

  16. Recovery of knee mobility after a static or mobile spacer in total knee infection

    NARCIS (Netherlands)

    Brunnekreef, J.J.; Hannink, G.; Mde, W. Malefijt

    2013-01-01

    The purpose of the study was to compare the recovery of knee mobility after two-stage revision of an infected total knee arthroplasty using a static or mobile spacer. At 12 months follow-up, none of the patients had a recurrent infection of their new prosthesis. Knee flexion was lower in the static

  17. Static and dynamic adaptation of insect photoreceptor responses to naturalistic stimuli

    Directory of Open Access Journals (Sweden)

    Andrew Stanton French

    2016-10-01

    Full Text Available We describe a new nonlinear dynamic model of insect phototransduction using a NLN (nonlinear, linear, nonlinear block structure. The first nonlinear stage provides a single exponential decline in gain and mean following the start of light stimulation. The linear stage uses a two-parameter log-normal convolution model previously applied alone to insect photoreceptors. The final stage is a static quadratic function. The model fitted current and voltage responses of isolated single photoreceptors from three different insect species with reasonable fidelity when they were stimulated by naturalistic time series having wide bandwidth and contrast, over a light intensity range of greater than 1:104. Mean squared error values for receptor current and receptor potential varied over approximately 2-60%, with many values below 10%. Linear log-normal filter parameters did not vary strongly with species or light intensity. Initial gain reduction was only large for the highest light levels, while the time constant of gain and mean reduction decreased with light intensity. The final nonlinearity changed from positively to negatively quadratic with increasing light intensity, indicating a change from threshold, or expansion to saturating compression with greater signal strength. Photoreceptor information transmission was estimated by linear information capacity and signal entropy measurements of both experimental data and predicted outputs of the model for identical stimuli at each light level. Comparison of actual and predicted data indicated significant added noise during phototransduction, with information being progressively lost by nonlinear behavior with increasing light intensity.

  18. Grid-connected integrated community energy system. Phase II, Stage 1, final report. Conceptual design, demand and fuel projections and cost analysis

    Energy Technology Data Exchange (ETDEWEB)

    1978-03-08

    The Phase I Report, Grid ICES, presented the broad alternatives and implications for development of an energy system satisfying thermal demand with the co-generation of electric power, all predicated on the use of solid fuels. Participants of the system are the University of Minnesota, operator and primary thermal user, and Northern States Power Company, primary electrical user; with St. Mary's Hospital, Fairview Hospital, and Augsburg College as Add-on Customers for the thermal service (Option I). Included for consideration are the Options of (II) solid waste disposal by the Pyrolysis Method, with heat recovery, and (III) conversion of a portion of the thermal system from steam to hot water distribution to increase co-generation capability and as a demonstration system for future expansion. This report presents the conceptual design of the energy system and each Option, with the economic implications identified so that selection of the final system can be made. Draft outline of the Environmental Assessment for the project is submitted as a separate report.

  19. Ventriculectomia parcial: um novo conceito no tratamento cirúrgico de cardiopatias em fase final Partial ventriculectomy: a new concept for surgical treatment of end stage cardiopathies

    Directory of Open Access Journals (Sweden)

    Randas J. V Batista

    1996-03-01

    cardiac problems and end stage congestive heart failure (NYHA IV with dilated cardiomyopathy underwent "Partial Ventriculectomy". The operation was based on Laplace's law (T-P.II.D and consisted of removal of a large wedge of muscle from the lateral wall of the left ventricle beginning at the apex and extending between the papillary muscles, ending proximal to the mitral annulus. The operation was performed under normothermic cardiopulmonary bypass and no cardioplegia was used. Pre-operative left ventriculography and echocardiography showed global hypocontractility of the hearts with ejection fraction lower than 20% in all patients who were considered candidates for cardiac transplantation. Males were predominant (n=73 and the age varied from 19 to 74 years. The pathologies were: viral miocarditis (n=12; post miocardioplasty (n=1; Chagas' disease (n=15; valvular disease (n=38; ischemic disease (n=16; idiopathic (n=21. Hospital mortality (30 days post operative (n=13: pulmonary embolus (n=4; renal failure (n=5; bleeding (n=4. Late deaths (after 30 days post-operative (n=10: arhythmia (n=6; "cardiac failure" (n=2; unknown (n=2; 8 patients required reoperation for bleeding. There were no infection and none required IAPB. All patients had nipride and 19 needed inotropics. Post-op ventriculographies and echocardiographies showed improvement of EF (from 100% to 300%. In conclusion, this new technique "Partial Ventriculectomy", with it's purpose of reducing the ventricular diameter, may benefit patients with end stage heart failure. And this new concept may, in our experience, give the patient improvement in his clinical status and increase life span.

  20. Measurement of Static Characteristics Pneumatic Motors with Elastic Working Elements

    OpenAIRE

    Kamil FOJTÁŠEK; Lukáš DVOŘÁK

    2012-01-01

    Into a category of pneumatic motors with elastic working parts belong air bellows, diaphragm motors and fluid muscles. All three types of these motors have some elastic part usually made of rubber. This part is deformed under the pressure of a compressed air or a mass load resulting in a final working effect. This paper deals with measuring of static characteristics of these motors.

  1. Statics of historic masonry constructions

    CERN Document Server

    Como, Mario

    2017-01-01

    Masonry constructions are the great majority of the buildings in Europe’s historic centres and the most important monuments of its architectural heritage. Given the age of these constructions, the demand for safety assessments and restoration projects is pressing and constant; still within the broad studies in the subject it is not yet recognised, in particular within the seismic area, a unitary approach to deal with Masonry structures. This successful book contributes to clarify the issues with a rigorous approach offering a comprehensive new Statics of Masonry Constructions. This third edition has been driven by some recent developments of the research in the field, and it gives the fundamentals of Statics with an original and rigorous mathematical formulation, further in-depth inquired in this new version. With many refinements and improvements, the book investigates the static behaviour of many historic monuments, such as the Gothic Cathedrals, the Mycenaean Tholoi, the Pantheon, the Colosseum, the dome...

  2. 78 FR 25767 - Certain Static Random Access Memories and Products Containing Same; Commission Determination To...

    Science.gov (United States)

    2013-05-02

    ... INTERNATIONAL TRADE COMMISSION [Investigation No. 337-TA-792] Certain Static Random Access Memories and Products Containing Same; Commission Determination To Review in Part a Final Initial... States after importation of certain static random access memories and products containing the same by...

  3. Static Analysis for Dynamic XML

    DEFF Research Database (Denmark)

    Christensen, Aske Simon; Møller, Anders; Schwartzbach, Michael Ignatieff

    2002-01-01

    We describe the summary graph lattice for dataflow analysis of programs that dynamically construct XML documents. Summary graphs have successfully been used to provide static guarantees in the JWIG language for programming interactive Web services. In particular, the JWIG compiler is able to check...

  4. Some Static Properties of Slinky

    OpenAIRE

    Eskandari-asl, Amir

    2018-01-01

    In this paper we use a simple discrete model for Slinky to explore some of its static properties. We derive some relations for vertically and U-shaped suspended Slinkies, based on which, some demonstrations are proposed that can be simply done in freshmen physics classes.

  5. Static Analysis of Dynamic Languages

    DEFF Research Database (Denmark)

    Madsen, Magnus

    with static type systems, such as Java and C# , but the same features are rarely available for dynamic languages such as JavaScript. The aim of this thesis is to investigate techniques for improving the tool- support for dynamic programming languages without imposing any artificial restrictions...

  6. Static Verification for Code Contracts

    Science.gov (United States)

    Fähndrich, Manuel

    The Code Contracts project [3] at Microsoft Research enables programmers on the .NET platform to author specifications in existing languages such as C# and VisualBasic. To take advantage of these specifications, we provide tools for documentation generation, runtime contract checking, and static contract verification.

  7. Static Analysis for Systems Biology

    DEFF Research Database (Denmark)

    Nielson, Flemming; Nielson, Hanne Riis; Rosa, D. Schuch da

    2004-01-01

    This paper shows how static analysis techniques can help understanding biological systems. Based on a simple example we illustrate the outcome of performing three different analyses extracting information of increasing precision. We conclude by reporting on the potential impact and exploitation o...... of these techniques in systems biology....

  8. Static Correctness of Hierarchical Procedures

    DEFF Research Database (Denmark)

    Schwartzbach, Michael Ignatieff

    1990-01-01

    A system of hierarchical, fully recursive types in a truly imperative language allows program fragments written for small types to be reused for all larger types. To exploit this property to enable type-safe hierarchical procedures, it is necessary to impose a static requirement on procedure calls...

  9. Static and dynamic buckling of thin-walled plate structures

    CERN Document Server

    Kubiak, Tomasz

    2013-01-01

    This monograph deals with buckling and postbuckling behavior of thin plates and thin-walled structures with flat wall subjected to static and dynamic load. The investigations are carried out in elastic range. The basic assumption here is the  thin plate theory. This method is used to determination the buckling load and postbuckling analysis of thin-walled structures subjected to static and dynamic load. The book introduces two methods for static and dynamic buckling investigation which allow for a wider understanding of the phenomenon. Two different methods also can allow uncoupling of the phenomena occurring at the same time and attempt to estimate their impact on the final result. A general mathematical model, adopted in proposed analytical-numerical method, enables the consideration of all types of stability loss i.e.local, global and interactive forms of buckling. The applied numerical-numerical method includes adjacent of walls, shear-lag phenomenon and a deplanation of cross-sections.

  10. Static standing and dynamic walking of a practical biped robot

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, Yuan F.; Rao, M.

    1987-01-01

    The study of static standing and dynamic walking of a practical biped robot is presented in this research report. A systematic method for describing the kinematic behavior of a biped robot is first developed. The development is based on the well-known Denavit-Hartenburg convention. As a result, the method is basically the same as the one used for robot manipulators, except for some considerations given to the unique functions and structure of a biped robot. The static standing of a biped robot is then studied. It is argued that static standing capability is very important if a biped robot is to be employed in an industrial environment. In order to measure the performance of the biped in static standing in terms of its stability, two parameters, stable margin and stable index, are introduced. Based on these parameters, optimal stability of the biped robot with one-foot and two-foot standing cases are discussed. For dynamic walking, a mathematical treatment is first described. Conclusion is reached that by proper positioning of the landing, stable dynamic walking can be realized. A practical biped robot is introduced in the final part of the report. Experimental results of static standing and dynamic walking of the biped robot are presented, to verify the theoretical results. 28 refs., 9 figs., 1 tab.

  11. The extended surface forces apparatus. IV. Precision static pressure control

    OpenAIRE

    Schurtenberger E; Heuberger M

    2011-01-01

    We report on design and performance of an extended surface forces apparatus (eSFA) built into a pressurized system. The aim of this instrument is to provide control over static pressure and temperature to facilitate direct surface force experiments in equilibrium with fluids at different loci of their phase diagram. We built an autoclave that can bear a miniature eSFA. To avoid mechanical or electrical feedtroughs the miniature apparatus uses an external surface coarse approach stage under am...

  12. Statics of historic masonry constructions

    CERN Document Server

    Como, Mario

    2016-01-01

    This successful book, which is now appearing in its second edition, presents a comprehensive new Statics of Masonry Constructions. Masonry constructions are the great majority of the buildings in Europe’s historic centres and the most important monuments in its architectural heritage. Given the age of these constructions, the demand for safety assessments and restoration projects is pressing and constant. The book you hold in hands contributes to fill this demand. The second edition integrates the original text of the first edition with new developments, widening and revisions, due to recent research studies achievements. The result is a book that gives a complete picture of the behaviour of the Masonry Constructions. First of all, it gives the fundamentals of its Statics, based on the no-tension assumption, and then it develops the Limit Analysis for the Masonry Constructions. In this framework, through an interdisciplinary approach combining Engineering and Architecture, the book also investigates the sta...

  13. Water cooled static pressure probe

    Science.gov (United States)

    Lagen, Nicholas T. (Inventor); Eves, John W. (Inventor); Reece, Garland D. (Inventor); Geissinger, Steve L. (Inventor)

    1991-01-01

    An improved static pressure probe containing a water cooling mechanism is disclosed. This probe has a hollow interior containing a central coolant tube and multiple individual pressure measurement tubes connected to holes placed on the exterior. Coolant from the central tube symmetrically immerses the interior of the probe, allowing it to sustain high temperature (in the region of 2500 F) supersonic jet flow indefinitely, while still recording accurate pressure data. The coolant exits the probe body by way of a reservoir attached to the aft of the probe. The pressure measurement tubes are joined to a single, larger manifold in the reservoir. This manifold is attached to a pressure transducer that records the average static pressure.

  14. Size scaling of static friction.

    Science.gov (United States)

    Braun, O M; Manini, Nicola; Tosatti, Erio

    2013-02-22

    Sliding friction across a thin soft lubricant film typically occurs by stick slip, the lubricant fully solidifying at stick, yielding and flowing at slip. The static friction force per unit area preceding slip is known from molecular dynamics (MD) simulations to decrease with increasing contact area. That makes the large-size fate of stick slip unclear and unknown; its possible vanishing is important as it would herald smooth sliding with a dramatic drop of kinetic friction at large size. Here we formulate a scaling law of the static friction force, which for a soft lubricant is predicted to decrease as f(m)+Δf/A(γ) for increasing contact area A, with γ>0. Our main finding is that the value of f(m), controlling the survival of stick slip at large size, can be evaluated by simulations of comparably small size. MD simulations of soft lubricant sliding are presented, which verify this theory.

  15. Static Analysis of Mobile Programs

    Science.gov (United States)

    2017-02-01

    and not allowed, to do. The second issue was that a fully static analysis was never a realistic possibility, because Java , the programming langauge...not justified by the test data). This idea came to define the project: use dynamic analyiss to guess the correct properties a program points of interest...scale to large programs it had to handle essentially all of the features of Java and could also be used as a general-purpose analysis engine. The

  16. Static and Dynamic Membrane Structures

    Directory of Open Access Journals (Sweden)

    Sergiu Ivanov

    2012-10-01

    Full Text Available While originally P systems were defined to contain multiset rewriting rules, it turned out that considering different types of rules may produce important results, such as increasing the computational power of the rules. This paper focuses on factoring out the concept of a membrane structure out of various P system models with the goal of providing useful formalisations. Both static and dynamic membrane structures are considered.

  17. Homotheties of cylindrically symmetric static spacetimes

    International Nuclear Information System (INIS)

    Qadir, A.; Ziad, M.; Sharif, M.

    1998-08-01

    In this note we consider the homotheties of cylindrically symmetric static spacetimes. We find that we can provide a complete list of all metrics that admit non-trivial homothetic motions and are cylindrically symmetric static. (author)

  18. Three Inexpensive Static-Electricity Demonstrations.

    Science.gov (United States)

    Gore, Gordon R.; Gregg, William R.

    1992-01-01

    Describes demonstrations to (1) construct an inexpensive static electricity detector; (2) obtain an abundant supply of either negative or positive charge using household items; and (3) create static electricity using a Tesla coil or Van de Graaff generator. (MDH)

  19. Developmental model of static allometry in holometabolous insects

    Science.gov (United States)

    Shingleton, Alexander W; Mirth, Christen K; Bates, Peter W

    2008-01-01

    The regulation of static allometry is a fundamental developmental process, yet little is understood of the mechanisms that ensure organs scale correctly across a range of body sizes. Recent studies have revealed the physiological and genetic mechanisms that control nutritional variation in the final body and organ size in holometabolous insects. The implications these mechanisms have for the regulation of static allometry is, however, unknown. Here, we formulate a mathematical description of the nutritional control of body and organ size in Drosophila melanogaster and use it to explore how the developmental regulators of size influence static allometry. The model suggests that the slope of nutritional static allometries, the ‘allometric coefficient’, is controlled by the relative sensitivity of an organ's growth rate to changes in nutrition, and the relative duration of development when nutrition affects an organ's final size. The model also predicts that, in order to maintain correct scaling, sensitivity to changes in nutrition varies among organs, and within organs through time. We present experimental data that support these predictions. By revealing how specific physiological and genetic regulators of size influence allometry, the model serves to identify developmental processes upon which evolution may act to alter scaling relationships. PMID:18460425

  20. Stage design

    International Nuclear Information System (INIS)

    Shacter, J.

    1975-01-01

    A method is described of cycling gases through a plurality of diffusion stages comprising the steps of admitting the diffused gases from a first diffusion stage into an axial compressor, simultaneously admitting the undiffused gases from a second diffusion stage into an intermediate pressure zone of said compressor corresponding in pressure to the pressure of said undiffused gases, and then admitting the resulting compressed mixture of diffused and undiffused gases into a third diffusion stage

  1. Calibration of Nanopositioning Stages

    Directory of Open Access Journals (Sweden)

    Ning Tan

    2015-12-01

    Full Text Available Accuracy is one of the most important criteria for the performance evaluation of micro- and nanorobots or systems. Nanopositioning stages are used to achieve the high positioning resolution and accuracy for a wide and growing scope of applications. However, their positioning accuracy and repeatability are not well known and difficult to guarantee, which induces many drawbacks for many applications. For example, in the mechanical characterisation of biological samples, it is difficult to perform several cycles in a repeatable way so as not to induce negative influences on the study. It also prevents one from controlling accurately a tool with respect to a sample without adding additional sensors for closed loop control. This paper aims at quantifying the positioning repeatability and accuracy based on the ISO 9283:1998 standard, and analyzing factors influencing positioning accuracy onto a case study of 1-DoF (Degree-of-Freedom nanopositioning stage. The influence of thermal drift is notably quantified. Performances improvement of the nanopositioning stage are then investigated through robot calibration (i.e., open-loop approach. Two models (static and adaptive models are proposed to compensate for both geometric errors and thermal drift. Validation experiments are conducted over a long period (several days showing that the accuracy of the stage is improved from typical micrometer range to 400 nm using the static model and even down to 100 nm using the adaptive model. In addition, we extend the 1-DoF calibration to multi-DoF with a case study of a 2-DoF nanopositioning robot. Results demonstrate that the model efficiently improved the 2D accuracy from 1400 nm to 200 nm.

  2. 30 CFR 18.26 - Static electricity.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Static electricity. 18.26 Section 18.26 Mineral... § 18.26 Static electricity. Nonmetallic rotating parts, such as belts and fans, shall be provided with a means to prevent an accumulation of static electricity. ...

  3. A Pedagogical Model of Static Friction

    OpenAIRE

    Pickett, Galen T.

    2015-01-01

    While dry Coulombic friction is an elementary topic in any standard introductory course in mechanics, the critical distinction between the kinetic and static friction forces is something that is both hard to teach and to learn. In this paper, I describe a geometric model of static friction that may help introductory students to both understand and apply the Coulomb static friction approximation.

  4. Static strain-aging in commercial purity alpha titanium

    International Nuclear Information System (INIS)

    Donoso, J.R.; Reed-Hill, R.E.

    1977-01-01

    Static strain-aging was investigated in commercial purity α-Ti, containing 0.41 at. percent of oxygen as the principal interstitial impurity. 17 μM grain size specimens, prestrained to 0.02 strain at a nominal strain-rate of 3.3 x 10 -4 s -1 , were aged in situ between 555 and 630 0 K for lengths of time between 150 and 2.55 x 10 5 seconds. Both the upper and lower yield point increments were employed as measures of the aging progress. Under the stated conditions, the static strain-aging response of the titanium appeared to consist of four stages, of which only Stages 1 and 2 were considered in this work. Stage 1 corresponded to a Haasen and Kelly type of yield point, while Stage 2, after correcting for the time-independent yield point increment of Stage 1, conformed to Cottrell aging, i.e., the increase in flow stress after aging followed a t/sup 2 / 3 / behavior. The activation energy deduced for the process is in good agreement with that for the diffusion of oxygen in titanium

  5. Measurement of Static Characteristics Pneumatic Motors with Elastic Working Elements

    Directory of Open Access Journals (Sweden)

    Kamil FOJTÁŠEK

    2012-06-01

    Full Text Available Into a category of pneumatic motors with elastic working parts belong air bellows, diaphragm motors and fluid muscles. All three types of these motors have some elastic part usually made of rubber. This part is deformed under the pressure of a compressed air or a mass load resulting in a final working effect. This paper deals with measuring of static characteristics of these motors.

  6. STATIC ANALYSIS OF LEAF SPRING

    OpenAIRE

    E VENUGOPAL GOUD; G HARINATH GOWD

    2012-01-01

    Leaf springs are special kind of springs used in automobile suspension systems. The advantage of leaf spring over helical spring is that the ends of the spring may be guided along a definite path as it deflects to act as a structural member in addition to energy absorbing device. The main function of leaf spring is not only tosupport vertical load but also to isolate road induced vibrations. It is subjected to millions of load cycles leading to fatigue failure. Static analysis determines the ...

  7. Pion and an improved static bag model

    Energy Technology Data Exchange (ETDEWEB)

    Donoghue, J.F.; Johnson, K.

    1980-04-01

    Quark-model calculations involve an extended static object localized in space. We introduce new methods, involving momentum-space wave packets, which account for this localization. These methods have little effect on heavy states, whose sizes are large compared to their Compton size 1/m, but are very important for light particles such as the pion. In this treatment the pion's mass is naturally very small, and, in order to connect with a spontaneously broken chiral symmetry, we require that m/sub ..pi../ vanish when the light quarks are massless. Expanding about this limit (and also readjusting the fit to other hadrons), we obtain m/sub q/=(m-italic/sub u/+m/sub d/)/2=33 MeV. We calculate F/sub ..pi../ approx. = 145 MeV (using a normalization such that F/sub ..pi../ vertical-bar /sub exp/=93 MeV), F/sub K//F/sub ..pi../ approx. = 1, and various corrections to static properties of baryons. In addition we explore the relationship of our methods with chiral perturbation theory, deriving the formula m/sub ..pi../ /sup 2/=(m-italic/sub u/+m/sub d/) < ..pi..(p) vertical-bar q-bar(0)q(0) vertical-bar ..pi..(p) > in the appropriate approximation and commenting on the quark mass obtained from the nucleon's sigma term. Finally we discuss the bag model's use of the scalar density q-barq as an order parameter describing the separation of the spontaneously broken vacuum phase from the perturbative vacuum of the bag's interior.

  8. Trading stages

    DEFF Research Database (Denmark)

    Steiner, Uli; Tuljapurkar, Shripad; Coulson, Tim

    2012-01-01

    because they are hard to use and interpret, and tools for age and stage structured populations are missing. We present easily interpretable expressions for the sensitivities and elasticities of life expectancy to vital rates in age-stage models, and illustrate their application with two biological......Interest in stage-and age structured models has recently increased because they can describe quantitative traits such as size that are left out of age-only demography. Available methods for the analysis of effects of vital rates on lifespan in stage-structured models have not been widely applied...... examples. Much of our approach relies on trading of time and mortality risk in one stage for time and risk in others. Our approach contributes to the new framework of the study of age- and stage-structured biodemography....

  9. Theory of multisource crosstalk reduction by phase-encoded statics

    KAUST Repository

    Schuster, Gerard T.

    2011-03-01

    Formulas are derived that relate the strength of the crosstalk noise in supergather migration images to the variance of time, amplitude and polarity shifts in encoding functions. A supergather migration image is computed by migrating an encoded supergather, where the supergather is formed by stacking a large number of encoded shot gathers. Analysis reveals that for temporal source static shifts in each shot gather, the crosstalk noise is exponentially reduced with increasing variance of the static shift and the square of source frequency. This is not too surprising because larger time shifts lead to less correlation between traces in different shot gathers, and so should tend to reduce the crosstalk noise. Analysis also reveals that combining both polarity and time statics is a superior encoding strategy compared to using either polarity statics or time statics alone. Signal-to-noise (SNR) estimates show that for a standard migration image and for an image computed by migrating a phase-encoded supergather; here, G is the number of traces in a shot gather, I is the number of stacking iterations in the supergather and S is the number of encoded/blended shot gathers that comprise the supergather. If the supergather can be uniformly divided up into Q unique sub-supergathers, then the resulting SNR of the final image is, which means that we can enhance image quality but at the expense of Q times more cost. The importance of these formulas is that they provide a precise understanding between different phase encoding strategies and image quality. Finally, we show that iterative migration of phase-encoded supergathers is a special case of passive seismic interferometry. We suggest that the crosstalk noise formulas can be helpful in designing optimal strategies for passive seismic interferometry and efficient extraction of Green\\'s functions from simulated supergathers. © 2011 The Authors Geophysical Journal International © 2011 RAS.

  10. Hubble expansion in static spacetime

    International Nuclear Information System (INIS)

    Rossler, Otto E.; Froehlich, Dieter; Movassagh, Ramis; Moore, Anthony

    2007-01-01

    A recently proposed mechanism for light-path expansion in a static spacetime is based on the moving-lenses paradigm. Since the latter is valid independently of whether space expands or not, a static universe can be used to better see the implications. The moving-lenses paradigm is related to the paradigm of dynamical friction. If this is correct, a Hubble-like law is implicit. It is described quantitatively. A bent in the Hubble-like line is predictably implied. The main underlying assumption is Price's Principle (PI 3 ). If the theory is sound, the greatest remaining problem in cosmology becomes the origin of hydrogen. Since Blandford's jet production mechanism for quasars is too weak, a generalized Hawking radiation hidden in the walls of cosmic voids is invoked. A second prediction is empirical: slow pattern changes in the cosmic microwave background. A third is ultra-high redshifts for Giacconi quasars. Bruno's eternal universe in the spirit of Augustine becomes a bit less outlandish

  11. Relationship between static foot posture and foot mobility

    Directory of Open Access Journals (Sweden)

    McPoil Thomas G

    2011-01-01

    Full Text Available Abstract Background It is not uncommon for a person's foot posture and/or mobility to be assessed during a clinical examination. The exact relationship, however, between static posture and mobility is not known. Objective The purpose of this study was to determine the degree of association between static foot posture and mobility. Method The static foot posture and foot mobility of 203 healthy individuals was assessed and then analyzed to determine if low arched or "pronated" feet are more mobile than high arched or "supinated" feet. Results The study demonstrated that those individuals with a lower standing dorsal arch height and/or a wider standing midfoot width had greater mobility in their foot. In addition, those individuals with higher Foot Posture Index (FPI values demonstrated greater mobility and those with lower FPI values demonstrated less mobility. Finally, the amount of foot mobility that an individual has can be predicted reasonably well using either a 3 or 4 variable linear regression model. Conclusions Because of the relationship between static foot posture and mobility, it is recommended that both be assessed as part of a comprehensive evaluation of a individual with foot problems.

  12. Relationship between static foot posture and foot mobility

    Science.gov (United States)

    2011-01-01

    Background It is not uncommon for a person's foot posture and/or mobility to be assessed during a clinical examination. The exact relationship, however, between static posture and mobility is not known. Objective The purpose of this study was to determine the degree of association between static foot posture and mobility. Method The static foot posture and foot mobility of 203 healthy individuals was assessed and then analyzed to determine if low arched or "pronated" feet are more mobile than high arched or "supinated" feet. Results The study demonstrated that those individuals with a lower standing dorsal arch height and/or a wider standing midfoot width had greater mobility in their foot. In addition, those individuals with higher Foot Posture Index (FPI) values demonstrated greater mobility and those with lower FPI values demonstrated less mobility. Finally, the amount of foot mobility that an individual has can be predicted reasonably well using either a 3 or 4 variable linear regression model. Conclusions Because of the relationship between static foot posture and mobility, it is recommended that both be assessed as part of a comprehensive evaluation of a individual with foot problems. PMID:21244705

  13. The Predictive Validity of the Static-99, Static-99R, and Static-2002/R: Which One to Use?

    Science.gov (United States)

    Reeves, Sophie G; Ogloff, James R P; Simmons, Melanie

    2017-06-01

    The use of Static tools (Static-99, Static-99R, Static-2002, and Static-2002R) in risk decision making involving sexual offenders is widespread internationally. This study compared the predictive accuracy and incremental validity of four Static risk measures in a sample of 621 Australian sexual offenders. Results indicated that approximately 45% of the sample recidivated (with 18.8% committing sexual offenses). All of the Static measures investigated yielded moderate predictive validity for sexual recidivism, which was comparable with other Australian and overseas studies. Area under the curve (AUC) values for the four measures across the 5-, 10-, and 15-year intervals ranged from .67 to .69. All of the Static measures discriminated quite well between low-risk and high-risk sexual offenders but less well for the moderate risk categories. When pitted together, none of the tools accounted for additional variance in sexual recidivism, above and beyond what the other measures accounted for. The overall results provide support for the use of Static measures as a component of risk assessment and decision making with Australian sexual offending populations. The limitations of this study and recommendations for further research are also discussed.

  14. Static and dynamic thyroid scintigraphy

    International Nuclear Information System (INIS)

    Mahlstedt, J.

    1986-01-01

    Static images as isolated investigation in thyroid diagnosis mainly provides morphologic information, and therefore sonography is largely applied for this purpose. 99m Tc-pertechnetate scans or 123 I-scans are indicated in cases of malpositions and serve to clarify lesions of unknown dignity. Additionally 201 Tl-chloride is suited for examinations with regard to metabolically active thyroid tissue, whereby differential diagnostic laboratory tests must be carried out to exclude parathyroid adenoma. Dynamic thyroid scans before and after regulation tests (suppression, stimulation) reflect the physiological correlation between the iodine avidity of the thyroid, the peripheral thyroid hormone concentrations and the hypophyseal regulation in the TRH-test. The main application of this procedure is the clarification of thyroid autonomy, i.e. indication, detection, quantification or exclusion of thyroid autonomy. For the treatment of immunogenic thyrotoxicosis, dynamic thyroid scintigraphy provides important information about the onset of remission, thus permitting to end thyreostatic therapy. (orig.) [de

  15. Statics learning from engineering examples

    CERN Document Server

    Emri, Igor

    2016-01-01

    This textbook introduces and explains the basic concepts on which statics is based utilizing real engineering examples. The authors emphasize the learning process by showing a real problem, analyzing it, simplifying it, and developing a way to solve it. This feature teaches students intuitive thinking in solving real engineering problems using the fundamentals of Newton’s laws. This book also: · Stresses representation of physical reality in ways that allow students to solve problems and obtain meaningful results · Emphasizes identification of important features of the structure that should be included in a model and which features may be omitted · Facilitates students' understanding and mastery of the "flow of thinking" practiced by professional engineers.

  16. Static Behaviour of Bucket Foundations

    DEFF Research Database (Denmark)

    Larsen, Kim André

    theory is proposed. The proposed expression applies to plane strain as well as axis-symmetric stress conditions for foundations with smooth or rough bases. A thorough experimental investigation of the static behaviour of bucket foundations subjected to combined loading is carried out. Laboratory tests...... as well as large-scale tests on bucket foundations subjected to low vertical load are performed during this work. Numerical simulations of the tests performed are carried out using the Mohr Coulomb material model and the commercial finite element code ABAQUS. Based on the present work, the finite element...... method is concluded to be a superior method in estimating the post peak behaviour as well as the combined capacity of bucket foundations in relation to the offshore wind turbine problem....

  17. Pulsed Current Static Electrical Contact Experiment

    National Research Council Canada - National Science Library

    Jones, Harry N; Neri, Jesse M; Boyer, Craig N; Cooper, Khershed P; Meger, Robert A

    2006-01-01

    Railguns involve both static and sliding electrical contacts, which must transmit the large transient electrical currents necessary to impart high forces onto a projectile for acceleration to hypervelocity...

  18. Staging atmospheres

    DEFF Research Database (Denmark)

    Bille, Mikkel; Bjerregaard, Peter; Sørensen, Tim Flohr

    2015-01-01

    The article introduces the special issue on staging atmospheres by surveying the philosophical, political and anthropological literature on atmosphere, and explores the relationship between atmosphere, material culture, subjectivity and affect. Atmosphere seems to occupy one of the classic...

  19. A multinuclear static NMR study of geopolymerisation

    Energy Technology Data Exchange (ETDEWEB)

    Favier, Aurélie, E-mail: aurelie.favier@epfl.ch [Univ Paris-Est, IFSTTAR, Materials Department, 14-20 bd Newton, F-77447 Marne la Vallée Cedex 2 (France); Habert, Guillaume [Institute for Construction and Infrastructure Management, ETH Zurich, CH-8093 Zurich (Switzerland); Roussel, Nicolas [Univ Paris-Est, IFSTTAR, Materials Department, 14-20 bd Newton, F-77447 Marne la Vallée Cedex 2 (France); D' Espinose de Lacaillerie, Jean-Baptiste [Ecole Supérieure de Physique et de Chimie Indusrtrielles de la Ville de Paris (ESPCI), ParisTech, PSL Research University, Soft Matter Sciences and Engineering Laboratory SIMM, CNRS UMR 7615, 10 rue Vauquelin, F-75005 Paris (France)

    2015-09-15

    Geopolymers are inorganic binders obtained by alkali activation of aluminosilicates. While the structure of geopolymers is now well understood, the details of the geopolymerisation reaction and their impact on the rheology of the paste remain uncertain. In this work, we follow the elastic properties of a paste made with metakaolin and sodium silicate solution. After the first sharp increase of elastic modulus occurring a few hundred of seconds after mixing and related to the heterogeneous formation of an alumina–silicate gel with a molar ratio Si/Al < 4 located at the grains boundaries, we focus on the progressive increase in elastic modulus on a period of few hours during the setting of the geopolymer. In this study, we combine the study of rheological properties of the paste with {sup 23}Na, {sup 27}Al and {sup 29}Si static NMR measurement in order to better understand the origin of this second increase in elastic modulus. Our results show that, after a few hours, Al and Na evolution in the liquid phase are concomitant. This suggests the precipitation of an aluminosilicate phase where Al is in tetrahedral position and Na compensates the charge. Furthermore, Si speciation confirms this result and allows us to identify the precipitation of a product, which has a chemical composition close to the final composition of geopolymer. This study provides strong evidence for a heterogeneous formation of an aluminosilicate glass directly from the first gel and the silicate solution without the need for a reorganisation of Gel 1 into Gel 2.

  20. Static Var Compensator Project for the SPS Electrical Network

    CERN Document Server

    Kahle, K

    2000-01-01

    This paper gives a progress report on the Static Var Compensator project BEF2 for the SPS electrical network. Following a market survey and a call for tenders, a contract has been awarded to ABB Sweden and the project is now in the phase of detailed performance studies, system design and ordering of the main electrical components. This progress report describes the electrical design, summarises the results of the harmonic filter design studies, discusses the interfacing of the control- and communication system and explains the mechanical layout of the Static Var Compensator and as well as the project co-ordination with the feeding BE substation renovation project. Finally, the project planning is presented and critical paths are evaluated.

  1. Small business life cycle: statics and dynamics (S

    Directory of Open Access Journals (Sweden)

    Matejun Marek

    2017-12-01

    Full Text Available The aim of the paper is the presentation of theoretical foundations and the structure of original, 8-stage statics and dynamics model in the small business life cycle. Based on theoretical considerations, two hypotheses concerning the impact of dynamic and static nature of the life-cycle stages on selected determinants and effects of SMEs’ development were formulated. The hypotheses were verified based on the results of the survey conducted on a sample of 1,741 SMEs from 22 countries of the European Union. The results indicate that companies in the dynamic life-cycle stages are run by more enterprising owners, operate in more promising markets with a higher potential and make greater use of market niches thus limiting the level of competition. At the same time, such companies are characterised by higher levels of flexibility and involvement in innovative activities, which translates into obtaining a significantly higher level of business performance, in the area of quantitative as well as qualitative results.

  2. Static Material Strength Determined Using a DAC

    Energy Technology Data Exchange (ETDEWEB)

    Cynn, H; Evans, W; Klepeis, J P; Lipp, M; Liermann, P; Yang, W

    2009-06-04

    By measuring sample thickness and pressure gradient using x-ray absorption and x-ray diffraction, respectively, the accurate static yield strengths of Ta and Fe were determined at high pressure. This improved method has several advantages over other similar methods to quantitatively determine static material strength.

  3. Static domain wall in braneworld gravity

    Energy Technology Data Exchange (ETDEWEB)

    Abdalla, M.C.B.; Carlesso, P.F. [UNESP, Universidade Estadual Paulista, Instituto de Fisica Teiorica, Rua Dr. Bento Teobaldo Ferraz 271, Bloco II, Barra-Funda, Caixa Postal 70532-2, Sao Paulo, SP (Brazil); Hoff da Silva, J.M. [UNESP, Universidade Estadual Paulista, Departamento de Fisica e Quimica, Guaratingueta, SP (Brazil)

    2014-01-15

    In this paper we consider a static domain wall inside a 3-brane. Different from the standard achievement obtained in General Relativity, the analysis performed here gives a consistency condition for the existence of static domain walls in a braneworld gravitational scenario. Also the behavior of the domain wall's gravitational field in the newtonian limit is shown. (orig.)

  4. Automatic incrementalization of Prolog based static analyses

    DEFF Research Database (Denmark)

    Eichberg, Michael; Kahl, Matthias; Saha, Diptikalyan

    2007-01-01

    Modem development environments integrate various static analyses into the build process. Analyses that analyze the whole project whenever the project changes are impractical in this context. We present an approach to automatic incrementalization of analyses that are specified as tabled logic...... incrementalizing a broad range of static analyses....

  5. Static balance and developmental coordination disorder

    NARCIS (Netherlands)

    Geuze, RH

    2003-01-01

    The development of static balance is a basic characteristic of normal motor development. Most of the developmental motor tests include a measure of static balance. Children with a developmental coordination disorder (DCD) often fail this item. Twenty-four children at risk for DCD with balance

  6. Optimal Static Range Reporting in One Dimension

    DEFF Research Database (Denmark)

    Alstrup, Stephen; Brodal, Gerth Stølting; Rauhe, Theis

    2001-01-01

    We consider static one dimensional range searching problems. These problems are to build static data structures for an integer set S \\subseteq U, where U = \\{0,1,\\dots,2^w-1\\}, which support various queries for integer intervals of U. For the query of reporting all integers in S contained within...

  7. Static Complexity Analysis of Higher Order Programs

    DEFF Research Database (Denmark)

    Avery, James Emil; Kristiansen, Lars; Moyen, Jean-Yves

    2009-01-01

    The overall goal of the research presented in this paper is to find^Mautomatic methods for static complexity analysis of higher order^Mprograms.......The overall goal of the research presented in this paper is to find^Mautomatic methods for static complexity analysis of higher order^Mprograms....

  8. Static response of deformable microchannels

    Science.gov (United States)

    Christov, Ivan C.; Sidhore, Tanmay C.

    2017-11-01

    Microfluidic channels manufactured from PDMS are a key component of lab-on-a-chip devices. Experimentally, rectangular microchannels are found to deform into a non-rectangular cross-section due to fluid-structure interactions. Deformation affects the flow profile, which results in a nonlinear relationship between the volumetric flow rate and the pressure drop. We develop a framework, within the lubrication approximation (l >> w >> h), to self-consistently derive flow rate-pressure drop relations. Emphasis is placed on handling different types of elastic response: from pure plate-bending, to half-space deformation, to membrane stretching. The ``simplest'' model (Stokes flow in a 3D rectangular channel capped with a linearly elastic Kirchhoff-Love plate) agrees well with recent experiments. We also simulate the static response of such microfluidic channels under laminar flow conditions using ANSYSWorkbench. Simulations are calibrated using experimental flow rate-pressure drop data from the literature. The simulations provide highly resolved deformation profiles, which are difficult to measure experimentally. By comparing simulations, experiments and our theoretical models, we show good agreement in many flow/deformation regimes, without any fitting parameters.

  9. Terapascal static pressure generation with ultrahigh yield strength nanodiamond.

    Science.gov (United States)

    Dubrovinskaia, Natalia; Dubrovinsky, Leonid; Solopova, Natalia A; Abakumov, Artem; Turner, Stuart; Hanfland, Michael; Bykova, Elena; Bykov, Maxim; Prescher, Clemens; Prakapenka, Vitali B; Petitgirard, Sylvain; Chuvashova, Irina; Gasharova, Biliana; Mathis, Yves-Laurent; Ershov, Petr; Snigireva, Irina; Snigirev, Anatoly

    2016-07-01

    Studies of materials' properties at high and ultrahigh pressures lead to discoveries of unique physical and chemical phenomena and a deeper understanding of matter. In high-pressure research, an achievable static pressure limit is imposed by the strength of available strong materials and design of high-pressure devices. Using a high-pressure and high-temperature technique, we synthesized optically transparent microballs of bulk nanocrystalline diamond, which were found to have an exceptional yield strength (~460 GPa at a confining pressure of ~70 GPa) due to the unique microstructure of bulk nanocrystalline diamond. We used the nanodiamond balls in a double-stage diamond anvil cell high-pressure device that allowed us to generate static pressures beyond 1 TPa, as demonstrated by synchrotron x-ray diffraction. Outstanding mechanical properties (strain-dependent elasticity, very high hardness, and unprecedented yield strength) make the nanodiamond balls a unique device for ultrahigh static pressure generation. Structurally isotropic, homogeneous, and made of a low-Z material, they are promising in the field of x-ray optical applications.

  10. Martian Atmospheric Pressure Static Charge Elimination Tool

    Science.gov (United States)

    Johansen, Michael R.

    2014-01-01

    A Martian pressure static charge elimination tool is currently in development in the Electrostatics and Surface Physics Laboratory (ESPL) at NASA's Kennedy Space Center. In standard Earth atmosphere conditions, static charge can be neutralized from an insulating surface using air ionizers. These air ionizers generate ions through corona breakdown. The Martian atmosphere is 7 Torr of mostly carbon dioxide, which makes it inherently difficult to use similar methods as those used for standard atmosphere static elimination tools. An initial prototype has been developed to show feasibility of static charge elimination at low pressure, using corona discharge. A needle point and thin wire loop are used as the corona generating electrodes. A photo of the test apparatus is shown below. Positive and negative high voltage pulses are sent to the needle point. This creates positive and negative ions that can be used for static charge neutralization. In a preliminary test, a floating metal plate was charged to approximately 600 volts under Martian atmospheric conditions. The static elimination tool was enabled and the voltage on the metal plate dropped rapidly to -100 volts. This test data is displayed below. Optimization is necessary to improve the electrostatic balance of the static elimination tool.

  11. Rotating UPS installations and dynamic energy storage. Comparison of static and rotating UPS and comparison of dynamic energy storage using batteries - Final Report; Rotierende USV-Anlagen und dynamische Energiespeicherung. Vergleich der statischen mit rotierenden USV-Anlagen und Vergleich der dynamischen Energiespeicherung mit Batterieanlagen - Schlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Mauchle, P.; Schnyder, G.

    2010-01-15

    As an alternative to the static UPS-Systems (uninterruptible power supply systems), rotating UPS-Systems can be applied. The application and the realisation of rotating UPS-Systems are different to the one of static UPS-Systems. Furthermore at the rotating UPS-Systems is to distinguish, if the UPS-System is realised as a diesel dynamic UPS-System, with an activity up from 400 kVA, or if the dynamic part is limited to the energy storage, with an activity up from 60 kVA. The diesel dynamic UPS-Systems are composed of a synchronous machine, an asynchronous machine with a flywheel, respectively a kinetic module and the diesel engine. The connection to the critical user at the low voltage network occurs using an inductor and the accordant switchgears. The application of a diesel dynamic UPS-System is optimal when it can be connected with an emergency power supply. With the realisation of dynamic energy storages, battery systems can be avoided respectively can be reduced or the lifetime of batteries can be extended. It is only possible to avoid the batteries if the requested autonomous time of the UPS-System is shorter than two minutes. Is an autonomous time longer than 2 minutes necessary, battery systems have to be realised for the energy storage. Thereby dynamic energy storage in parallel to the battery system is useful, because the dynamic energy storage will compensate temporary voltage drops or short power failures. In this way the number of charge and discharge cycles of the battery system will be reduced and therefore the lifetime of the battery will be extended. The use of a dynamic or static UPS system is dependent on the requirements of the powered load. Taking into account various criteria it can be found for each specific application the optimal type of UPS system. (authors)

  12. Dynamic salivary gland scintigraphy in clinical sicca syndrome: comparison with static images

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Euy Neyng; Shon, Hyung Sun; Choi, Jung Eun; Kim, Sung Hoon; Chung, Young An; Chung, Soo Kyo; Kim, Choon Yul [College of Medicine, The Catholic Univ. of Korea, Seoul (Korea, Republic of)

    2001-02-01

    In this study, we compared the quantitative characteristics of dynamic salivary gland scintigraphy with static scintigraphy in patients with clinical sicca syndrome using Tc-99m pertechnetate. Fifty-two parotid glands and 52 submandibular glands out of 26 patients with clinical sicca syndrome were studied by dynamic and static salivary gland scintigraphy. Ten normal volunteers were also studied as a control group for comparison of scintigraphic parameters. Ten minutes after injection of 370 MBq Tc-99m pertechnetate, we obtained pre-stimulus static images for a few minutes. Then dynamic salivary gland scintigraphy with lemon juice stimulation was performed for 20 minutes. Finally we obtained post-stimulus static images after dynamic images. On dynamic study, functional parameters such as uptake rate, secretion rate and re-uptake rate were calculated. The results of dynamic study and static images were compared. On dynamic study, we could obtain functional parameters of salivary glands successfully. On dynamic study, 22 parotid glands and 22 submandibular glands out of each 52 glands are abnormal. The static images demonstrated somewhat different results, of which reasons we could assume via dynamic study. Dynamic salivary gland scintigraphy using Tc-99m perechnetate were more functional than static images and might be useful in the assessment of the functional change of the salivary gland in patients with clinical sicca syndrome.

  13. A static axisymmetric exact solution of f(R)-gravity

    Energy Technology Data Exchange (ETDEWEB)

    Gutierrez-Pineres, Antonio C., E-mail: acgutierrez@correo.nucleares.unam.mx [Facultad de Ciencias Basicas, Universidad Tecnologica de Bolivar, CO 131001 Cartagena de Indias (Colombia); Instituto de Ciencias Nucleares, Universidad Nacional Autonoma de Mexico, A.P. 70-543, 04510 Mexico D.F. (Mexico); Lopez-Monsalvo, Cesar S., E-mail: cesar.slm@correo.nucleares.unam.mx [Instituto de Ciencias Nucleares, Universidad Nacional Autonoma de Mexico, A.P. 70-543, 04510 Mexico D.F. (Mexico)

    2013-01-29

    We present an exact, axially symmetric, static, vacuum solution for f(R)-gravity in Weyl's canonical coordinates. We obtain a general explicit expression for the dependence of df(R)/dR upon the r and z coordinates and then the corresponding explicit form of f(R), which must be consistent with the field equations. We analyze in detail the modified Schwarzschild solution in prolate spheroidal coordinates. Finally, we study the curvature invariants and show that, in the case of f(R){ne}R, this solution corresponds to a naked singularity.

  14. Static phantom wormholes of finite size

    Science.gov (United States)

    Cataldo, Mauricio; Orellana, Fabian

    2017-09-01

    In this paper we derive new static phantom traversable wormholes by assuming a shape function with a quadratic dependence on the radial coordinate r . We mainly focus our study on wormholes sustained by exotic matter with positive energy density (as seen by any static observer) and a variable equation of state pr/ρ wormhole spacetimes extending to infinity, we show that a quadratic shape function allows us to construct static spacetimes of finite size, composed of a phantom wormhole connected to an anisotropic spherically symmetric distribution of dark energy. The wormhole part of the full spacetime does not fulfill the dominant energy condition, while the dark energy part does.

  15. Staging Mobilities

    DEFF Research Database (Denmark)

    Jensen, Ole B.

    In recent years, the social sciences have taken a “mobilities turn.” There has been a developing realisation that mobilities do not “just happen.” Mobilities are carefully and meticulously designed, planned and staged (from above). However, they are equally importantly acted out, performed and li......, the book asks: what are the physical, social, technical, and cultural conditions to the staging of contemporary urban mobilities?...... that mobility is more than movement between point A and B. It explores how the movement of people, goods, information, and signs influences human understandings of self, other and the built environment. Moving towards a new understanding of the relationship between movement, interaction and environments...

  16. A novel hybrid actuation mechanism based XY nanopositioning stage with totally decoupled kinematics

    Science.gov (United States)

    Zhu, Wu-Le; Zhu, Zhiwei; Guo, Ping; Ju, Bing-Feng

    2018-01-01

    This paper reports the design, analysis and testing of a parallel two degree-of-freedom piezo-actuated compliant stage for XY nanopositioning by introducing an innovative hybrid actuation mechanism. It mainly features the combination of two Scott-Russell and a half-bridge mechanisms for double-stage displacement amplification as well as moving direction modulation. By adopting the leaf-type double parallelogram (LTDP) structures at both input and output ends of the hybrid mechanism, the lateral stiffness and dynamic characteristics are significantly improved while the parasitic motions are greatly eliminated. The XY nanopositioning stage is constructed with two orthogonally configured hybrid mechanisms along with the LTDP mechanisms for totally decoupled kinematics at both input and output ends. An analytical model was established to describe the complete elastic deformation behavior of the stage, with further verification through the finite element simulation. Finally, experiments were implemented to comprehensively evaluate both the static and dynamic performances of the proposed stage. Closed-loop control of the piezoelectric actuators (PEA) by integrating strain gauges was also conducted to effectively eliminate the nonlinear hysteresis of the stage.

  17. Static Electricity-Responsive Supramolecular Assembly.

    Science.gov (United States)

    Jintoku, Hirokuni; Ihara, Hirotaka; Matsuzawa, Yoko; Kihara, Hideyuki

    2017-12-01

    Stimuli-responsive materials can convert between molecular scale and macroscopic scale phenomena. Two macroscopic static electricity-responsive phenomena based on nanoscale supramolecular assemblies of a zinc porphyrin derivative are presented. One example involves the movement of supramolecular assemblies in response to static electricity. The assembly of a pyridine (Py) complex of the above-mentioned derivative in cyclohexane is drawn to a positively charged material, whereas the assembly of a 3,5-dimethylpyridine complex is drawn to a negatively charged material. The second phenomenon involves the movement of a non-polar solvent in response to static electrical stimulation. A cyclohexane solution containing a small quantity of the Py-complexed assembly exhibited a strong movement response towards negatively charged materials. Based on spectroscopic measurements and electron microscope observations, it was revealed that the assembled formation generates the observed response to static electricity. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Static potentials from an extended gauge symmetry

    International Nuclear Information System (INIS)

    Doria, R.M.; Helayel Neto, J.A.

    1985-01-01

    Static potentials derived from the inclusion of more than one vector field in a single simple group are calculated. A confinement mechanism including colourful unphysical particle is discussed. (Author) [pt

  19. Proximity and Innovation : From Statics to Dynamics

    NARCIS (Netherlands)

    Balland, P.A.|info:eu-repo/dai/nl/330821369; Boschma, R.A.|info:eu-repo/dai/nl/123155541; Frenken, K.|info:eu-repo/dai/nl/207145253

    2015-01-01

    Despite theoretical and empirical advances, the proximity framework has remained essentially static. A dynamic extension of the proximity framework is proposed that accounts for co-evolutionary dynamics between knowledge networking and proximity. For each proximity dimension, how proximities might

  20. Static Water Vapor Feed Electrolyzer Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Development of a static vapor feed electrolyzer utilizing an advanced bipolar plate that produces sub-saturated H2 and O2 is proposed. This novel bipolar design can...

  1. Model Checking as Static Analysis: Revisited

    DEFF Research Database (Denmark)

    Zhang, Fuyuan; Nielson, Flemming; Nielson, Hanne Riis

    2012-01-01

    We show that the model checking problem of the μ-calculus can be viewed as an instance of static analysis. We propose Succinct Fixed Point Logic (SFP) within our logical approach to static analysis as an extension of Alternation-free Least Fixed Logic (ALFP). We generalize the notion of stratific......We show that the model checking problem of the μ-calculus can be viewed as an instance of static analysis. We propose Succinct Fixed Point Logic (SFP) within our logical approach to static analysis as an extension of Alternation-free Least Fixed Logic (ALFP). We generalize the notion...... of stratification to weak stratification and establish a Moore Family result for the new logic as well. The semantics of the μ-calculus is encoded as the intended model of weakly stratified clause sequences in SFP....

  2. Static Members of Classes in C#

    Directory of Open Access Journals (Sweden)

    Adrian LUPASC

    2017-12-01

    Full Text Available The C# language is object-oriented, which is why the declared member data must be part of a class. Thus, there is no possibility to declare certain variables that can be accessed from anywhere within the application, as it happens, for example, with global variables at the C language level. Making this work in C# is possible through static members of the class. Declaring a class implies defining some of its member data that later receive values when creating each object. A static member of the class can be interpreted as belonging only to the class, not to the objects subsequently created, which means that for the non-static data, there are as many children as there were objects created, while for the static ones there is only one copy, regardless of the number of created objects. In this regard, this paper presents the main aspects that characterize these abstract concepts of object oriented programming in general and C# language in particular, detailing how to develop an application that includes both static and non-static members. At the same time, particularities in the mirror for the two types of data, restrictions on use and potential limitations are presented.

  3. Duration Dependent Effect of Static Stretching on Quadriceps and Hamstring Muscle Force

    Directory of Open Access Journals (Sweden)

    Leyla Alizadeh Ebadi

    2018-03-01

    Full Text Available The aim of this study was to determine the acute effect of static stretching on hamstring and quadriceps muscles’ isokinetic strength when applied for various durations to elite athletes, to investigate the effect of different static stretching durations on isokinetic strength, and finally to determine the optimal stretching duration. Fifteen elite male athletes from two different sport branches (10 football and five basketball participated in this study. Experimental protocol was designed as 17 repetitive static stretching exercises for hamstring and quadriceps muscle groups according to the indicated experimental protocols; ((A 5 min jogging; (B 5 min jogging followed by 15 s static stretching; (C 5 min jogging followed by 30 s static stretching; (D 5 min jogging, followed by static stretching for 45 s. Immediately after each protocol, an isokinetic strength test consisting of five repetitions at 60°/s speed and 20 repetitions at 180°/s speed was recorded for the right leg by the Isomed 2000 device. Friedman variance analysis test was employed for data analysis. According to the analyzes, it was observed that 5 min jogging and 15 s stretching exercises increased the isokinetic strength, whereas 30 and 45 s stretching exercises caused a decrease.

  4. Acceleration of a Static Observer Near the Event Horizon of a Static Isolated Black Hole.

    Science.gov (United States)

    Doughty, Noel A.

    1981-01-01

    Compares the magnitude of the proper acceleration of a static observer in a static, isolated, spherically symmetric space-time region with the Newtonian result including the situation in the interior of a perfect-fluid star. This provides a simple physical interpretation of surface gravity and illustrates the global nature of the event horizon.…

  5. 14 CFR 23.177 - Static directional and lateral stability.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Static directional and lateral stability... Flight Stability § 23.177 Static directional and lateral stability. (a) The static directional stability... first, and at speeds from 1.2 VS1 to VO, the rudder pedal force must not reverse. (b) The static lateral...

  6. From Flow Logic to Static Type Systems in Coordination Languages

    DEFF Research Database (Denmark)

    De Nicola, Rocco; Gorla, Daniele; Hansen, René Rydhof

    2008-01-01

    ; therefore, the correctness properties cannot be statically enforced. By contrast, static analysis approaches based on Flow Logic usually guarantee properties statically. In this paper we show how to combine these two approaches to obtain a static type system for describing secure access to tuple spaces...

  7. 30 CFR 57.6602 - Static electricity dissipation during loading.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Static electricity dissipation during loading... MINES Explosives Extraneous Electricity-Surface and Underground § 57.6602 Static electricity dissipation... generates a static electricity hazard— (a) An evaluation of the potential static electricity hazard shall be...

  8. Utility of the Static-99 and Static-99R With Latino Sex Offenders.

    Science.gov (United States)

    Leguízamo, Alejandro; Lee, Seung C; Jeglic, Elizabeth L; Calkins, Cynthia

    2017-12-01

    The predictive validity of the Static-99 measures with ethnic minorities in the United States has only recently been assessed with mixed results. We assessed the predictive validity of the Static-99 and Static-99R with a sample of Latino sex offenders ( N = 483) as well as with two subsamples (U.S.-born, including Puerto Rico, and non-U.S.-born). The overall sexual recidivism rate was very low (1.9%). Both the Static-99 measures were able to predict sexual recidivism for offenders born in the United States and Puerto Rico, but neither was effective in doing so for other Latino immigrants. Calibration analyses ( N = 303) of the Static-99R were consistent with the literature and provided support for the potential use of the measure with Latinos born in the United States and Puerto Rico. These findings and their implications are discussed as they pertain to the assessment of Latino sex offenders.

  9. Extending and Enhancing SAS (Static Analysis Suite)

    CERN Document Server

    Ho, David

    2016-01-01

    The Static Analysis Suite (SAS) is an open-source software package used to perform static analysis on C and C++ code, helping to ensure safety, readability and maintainability. In this Summer Student project, SAS was enhanced to improve ease of use and user customisation. A straightforward method of integrating static analysis into a project at compilation time was provided using the automated build tool CMake. The process of adding checkers to the suite was streamlined and simplied by developing an automatic code generator. To make SAS more suitable for continuous integration, a reporting mechanism summarising results was added. This suitability has been demonstrated by inclusion of SAS in the Future Circular Collider Software nightly build system. Scalability of the improved package was demonstrated by using the tool to analyse the ROOT code base.

  10. Static Analysis for JavaScript

    DEFF Research Database (Denmark)

    Jensen, Simon Holm

    Web applications present unique challenges to designers of static analysis tools. One of these challenges is the language JavaScript used for client side scripting in the browser. JavaScript is a complex language with many pitfalls and poor tool support compared to other languages....... This dissertation describes the design and implementation of a static analysis for JavaScript that can assist programmers in finding bugs in code during development. We describe the design of a static analysis tool for JavaScript, built using the monotone framework. This analysis infers detailed type information...... about programs. This information can be used to detect bugs such as null pointer dereferences and unintended type coercions. The analysis is sound, enabling it to prove the absence of certain program errors. JavaScript is usually run within the context of the browser and the DOM API. The major...

  11. On the geometric phenomenology of static friction

    Science.gov (United States)

    Ghosh, Shankar; Merin, A. P.; Nitsure, Nitin

    2017-09-01

    In this note we introduce a hierarchy of phase spaces for static friction, which give a graphical way to systematically quantify the directional dependence in static friction via subregions of the phase spaces. We experimentally plot these subregions to obtain phenomenological descriptions for static friction in various examples where the macroscopic shape of the object affects the frictional response. The phase spaces have the universal property that for any experiment in which a given object is put on a substrate fashioned from a chosen material with a specified nature of contact, the frictional behaviour can be read off from a uniquely determined classifying map on the control space of the experiment which takes values in the appropriate phase space.

  12. On the geometric phenomenology of static friction.

    Science.gov (United States)

    Ghosh, Shankar; Merin, A P; Nitsure, Nitin

    2017-09-06

    In this note we introduce a hierarchy of phase spaces for static friction, which give a graphical way to systematically quantify the directional dependence in static friction via subregions of the phase spaces. We experimentally plot these subregions to obtain phenomenological descriptions for static friction in various examples where the macroscopic shape of the object affects the frictional response. The phase spaces have the universal property that for any experiment in which a given object is put on a substrate fashioned from a chosen material with a specified nature of contact, the frictional behaviour can be read off from a uniquely determined classifying map on the control space of the experiment which takes values in the appropriate phase space.

  13. Statics and rotational dynamics of composite beams

    CERN Document Server

    Ghorashi, Mehrdaad

    2016-01-01

    This book presents a comprehensive study of the nonlinear statics and dynamics of composite beams and consists of solutions with and without active elements embedded in the beams. The static solution provides the initial conditions for the dynamic analysis. The dynamic problems considered include the analyses of clamped (hingeless) and articulated (hinged) accelerating rotating beams. Two independent numerical solutions for the steady state and the transient responses are presented. The author illustrates that the transient solution of the nonlinear formulation of accelerating rotating beam converges to the steady state solution obtained by the shooting method. Other key areas considered include calculation of the effect of perturbing the steady state solution, coupled nonlinear flap-lag dynamics of a rotating articulated beam with hinge offset and aerodynamic damping, and static and dynamic responses of nonlinear composite beams with embedded anisotropic piezo-composite actuators. The book is intended as a t...

  14. Sawja: Static Analysis Workshop for Java

    Science.gov (United States)

    Hubert, Laurent; Barré, Nicolas; Besson, Frédéric; Demange, Delphine; Jensen, Thomas; Monfort, Vincent; Pichardie, David; Turpin, Tiphaine

    Static analysis is a powerful technique for automatic verification of programs but raises major engineering challenges when developing a full-fledged analyzer for a realistic language such as Java. Efficiency and precision of such a tool rely partly on low level components which only depend on the syntactic structure of the language and therefore should not be redesigned for each implementation of a new static analysis. This paper describes the Sawja library: a static analysis workshop fully compliant with Java 6 which provides OCaml modules for efficiently manipulating Java bytecode programs. We present the main features of the library, including i) efficient functional data-structures for representing a program with implicit sharing and lazy parsing, ii) an intermediate stack-less representation, and iii) fast computation and manipulation of complete programs. We provide experimental evaluations of the different features with respect to time, memory and precision.

  15. Thermal effects in static friction: thermolubricity.

    Science.gov (United States)

    Franchini, A; Bortolani, V; Santoro, G; Brigazzi, M

    2008-10-01

    We present a molecular dynamics analysis of the static friction between two thick slabs. The upper block is formed by N2 molecules and the lower block by Pb atoms. We study the effects of the temperature as well as the effects produced by the structure of the surface of the lower block on the static friction. To put in evidence the temperature effects we will compare the results obtained with the lower block formed by still atoms with those obtained when the atoms are allowed to vibrate (e.g., with phonons). To investigate the importance of the geometry of the surface of the lower block we apply the external force in different directions, with respect to a chosen crystallographic direction of the substrate. We show that the interaction between the lattice dynamics of the two blocks is responsible for the strong dependence of the static friction on the temperature. The lattice dynamics interaction between the two blocks strongly reduces the static friction, with respect to the case of the rigid substrate. This is due to the large momentum transfer between atoms and the N2 molecules which disorders the molecules of the interface layer. A further disorder is introduced by the temperature. We perform calculations at T = 20K which is a temperature below the melting, which for our slab is at 50K . We found that because of the disorder the static friction becomes independent of the direction of the external applied force. The very low value of the static friction seems to indicate that we are in a regime of thermolubricity similar to that observed in dynamical friction.

  16. A Logical Characterisation of Static Equivalence

    DEFF Research Database (Denmark)

    Hüttel, Hans; Pedersen, Michael D.

    2007-01-01

    The work of Abadi and Fournet introduces the notion of a frame to describe the knowledge of the environment of a cryptographic protocol. Frames are lists of terms; two frames are indistinguishable under the notion of static equivalence if they satisfy the same equations on terms. We present a first......-order logic for frames with quantification over environment knowledge which, under certain general conditions, characterizes static equivalence and is amenable to construction of characteristic formulae. The logic can be used to reason about environment knowledge and can be adapted to a particular application...

  17. QuickChecking Static Analysis Properties

    DEFF Research Database (Denmark)

    Midtgaard, Jan; Møller, Anders

    2015-01-01

    A static analysis can check programs for potential errors. A natural question that arises is therefore: who checks the checker? Researchers have given this question varying attention, ranging from basic testing techniques, informal monotonicity arguments, thorough pen-and-paper soundness proofs......, to verified fixed point checking. In this paper we demonstrate how quickchecking can be useful for testing a range of static analysis properties with limited effort. We show how to check a range of algebraic lattice properties, to help ensure that an implementation follows the formal specification...

  18. QuickChecking static analysis properties

    DEFF Research Database (Denmark)

    Midtgaard, Jan; Møller, Anders

    2017-01-01

    A static analysis can check programs for potential errors. A natural question that arises is therefore: who checks the checker? Researchers have given this question varying attention, ranging from basic testing techniques, informal monotonicity arguments, thorough pen-and-paper soundness proofs......, to verified fixed point checking. In this paper, we demonstrate how quickchecking can be useful to test a range of static analysis properties with limited effort. We show how to check a range of algebraic lattice properties, to help ensure that an implementation follows the formal specification of a lattice...

  19. Static compensators (STATCOMs) in power systems

    CERN Document Server

    Shahnia, Farhad; Ghosh, Arindam

    2014-01-01

    A static compensator (STATCOM), also known as static synchronous compensator, is a member of the flexible alternating current transmission system (FACTS) devices. It is a power-electronics based regulating device which is composed of a voltage source converter (VSC) and is shunt-connected to alternating current electricity transmission and distribution networks. The voltage source is created from a DC capacitor and the STATCOM can exchange reactive power with the network. It can also supply some active power to the network, if a DC source of power is connected across the capacitor. A STATCOM

  20. MEMS linear and nonlinear statics and dynamics

    CERN Document Server

    Younis, Mohammad I

    2011-01-01

    MEMS Linear and Nonlinear Statics and Dynamics presents the necessary analytical and computational tools for MEMS designers to model and simulate most known MEMS devices, structures, and phenomena. This book also provides an in-depth analysis and treatment of the most common static and dynamic phenomena in MEMS that are encountered by engineers. Coverage also includes nonlinear modeling approaches to modeling various MEMS phenomena of a nonlinear nature, such as those due to electrostatic forces, squeeze-film damping, and large deflection of structures. The book also: Includes examples of nume

  1. Final Report

    Energy Technology Data Exchange (ETDEWEB)

    DeTar, Carleton [P.I.

    2012-12-10

    This document constitutes the Final Report for award DE-FC02-06ER41446 as required by the Office of Science. It summarizes accomplishments and provides copies of scientific publications with significant contribution from this award.

  2. Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Gurney, Kevin R. [Arizona Univ., Mesa, AZ (United States)

    2015-01-12

    This document constitutes the final report under DOE grant DE-FG-08ER64649. The organization of this document is as follows: first, I will review the original scope of the proposed research. Second, I will present the current draft of a paper nearing submission to Nature Climate Change on the initial results of this funded effort. Finally, I will present the last phase of the research under this grant which has supported a Ph.D. student. To that end, I will present the graduate student’s proposed research, a portion of which is completed and reflected in the paper nearing submission. This final work phase will be completed in the next 12 months. This final workphase will likely result in 1-2 additional publications and we consider the results (as exemplified by the current paper) high quality. The continuing results will acknowledge the funding provided by DOE grant DE-FG-08ER64649.

  3. If it changes it must be a process: study of emotion and coping during three stages of a college examination.

    Science.gov (United States)

    Folkman, S; Lazarus, R S

    1985-01-01

    This natural experiment provides substantial evidence for the following major themes, which are based on a cognitively oriented, process-centered theory of stress and coping: First, a stressful encounter should be viewed as a dynamic, unfolding process, not as a static, unitary event. Emotion and coping (including the use of social support) were assessed at three stages of a midterm examination: the anticipation stage before the exam, the waiting stage after the exam and before grades were announced, and after grades were posted. For the group as a whole there were significant changes in emotions and coping (including the use of social support) across the three stages. Second, people experience seemingly contradictory emotions and states of mind during every stage of an encounter. In this study, for example, subjects experienced both threat emotions and challege emotions. The complexity of emotions and their cognitive appraisals reflects ambiguity regarding the multifaceted nature of the exam and its meanings, especially during the anticipation stage. Third, coping is a complex process. On the average, subjects used combinations of most of the available forms of problem-focused coping and emotion-focused coping at every stage of the exam. Different forms of coping were salient during the anticipation and waiting stages. Problem-focused coping and emphasizing the positive were more prominent during the former, and distancing more prominent during the latter. Finally, despite normatively shared emotional reactions at each stage, substantial individual differences remained. Using selected appraisal and coping variables, and taking grade point averages (GPA) into account, approximately 48% of the variances in threat and challenge emotions at the anticipation stage was explained. Controlling for variance due to the grade received, appraisal, and coping variables accounted for 28% of the variance in positive and negative emotions at the outcome stage. Including grade, 57

  4. Experimental studies on a single-stage compressor equipped with profiles with controlled retardation. Phase 2. Final report; Experimentelle Untersuchungen an einem einstufigen Verdichter mit Profilen mit kontrollierter Verzoegerung. Phase 2. Schlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Blaha, C.; Schulze, G.

    1996-04-01

    As part of the TurboTech study detailed measurements were performed on compressor cascades, single-stage machines, and whole compressors. The purpose of this was to gain greater clarity concerning flow conditions in compressors. The experimental results obtained were to permit a refinement of the calculation methods thus creating a reliable tool for dimensioning the HTGT compressors. The project described here is dedicated to the single stage. The tasks of phase II can be divided as follows: determination of the performance map; numerical simulation of operating behaviour; dimensioning check; analysis of the simulation and measurements and their comparison; and further measurements for the study of special flow phenomena and development of an experimental - data base for the validation of calculation methods. (orig./GL) [Deutsch] Im Rahmen von TurboTech werden detaillierte Messungen an Verdichtergittern, einstufigen Maschinen und Gesamtverdichtern durchgefuehrt, um groessere Klarheit ueber die Stroemungsverhaeltnisse in Verdichtern zu erlangen. Hierbei sollen mit Hilfe der Versuchsergebnisse die Rechenverfahren verfeinert werden, um so ein zuverlaessiges Werkzeug zur Auslegung des HTGT Verdichters in die Hand zu bekommen. Das beschriebene Vorhaben ist der Einzelstufe gewidmet. Die Aufgaben der Phase II unterteilten sich in folgende Punkte: - Vermessung des Kennfeldes - Numerische Simulation des Betriebsverhaltens - Ueberpruefung der Auslegung - Analyse der Simulation und der Messungen sowie deren Vergleich - Durchfuehrung weiterer Messungen zur Untersuchung spezieller Stroemungsphaenomene und Schaffung einer Basis experimenteller Daten zur Validierung von Rechenverfahren. (orig./GL)

  5. Static Typing for Object-Oriented Programming

    DEFF Research Database (Denmark)

    Schwartzbach, Michael Ignatieff; Palsberg, Jens

    1994-01-01

    We develop a theory of statically typed object-oriented languages. It represents classes as labeled, regular trees, types as finit sets of classes , and sub-classing as a partial order on trees. We show that our sub-classing order strictly generalizes inheritance, and that a novel genericity...

  6. Static Validation of a Voting Protocol

    DEFF Research Database (Denmark)

    Nielsen, Christoffer Rosenkilde; Andersen, Esben Heltoft; Nielson, Hanne Riis

    2005-01-01

    The desired security properties of electronic voting protocols include verifiability, accuracy, democracy and fairness. In this paper we use a static program analysis tool to validate these properties for one of the classical voting protocols under appropriate assumptions. The protocol is formali...

  7. Static Analysis for Java Servlets and JSP

    DEFF Research Database (Denmark)

    Kirkegaard, Christian; Møller, Anders

    2006-01-01

    We present an approach for statically reasoning about the behavior of Web applications that are developed using Java Servlets and JSP. Specifically, we attack the problems of guaranteeing that all output is well-formed and valid XML and ensuring consistency of XHTML form fields and session state...

  8. Static, Lightweight Includes Resolution for PHP

    NARCIS (Netherlands)

    M.A. Hills (Mark); P. Klint (Paul); J.J. Vinju (Jurgen)

    2014-01-01

    htmlabstractDynamic languages include a number of features that are challenging to model properly in static analysis tools. In PHP, one of these features is the include expression, where an arbitrary expression provides the path of the file to include at runtime. In this paper we present two

  9. Supporting software inspection with static profiling

    NARCIS (Netherlands)

    Boogerd, C.; Moonen, L.

    2009-01-01

    Static software checking tools are useful as an additional automated software inspection step that can easily be integrated in the development cycle and assist in creating secure, reliable and high quality code. However, an often quoted disadvantage of these tools is that they generate an inordinate

  10. Prioritizing software inspection results using static profiling

    NARCIS (Netherlands)

    Boogerd, C.; Moonen, L.

    2006-01-01

    Static software checking tools are useful as an additional automated software inspection step that can easily be integrated in the development cycle and assist in creating secure, reliable and high quality code. However, an often quoted disadvantage of these tools is that they generate an overly

  11. PARAMETRIC RESONANSE IN STATICALLY INDETERMINATE FRAMES

    Directory of Open Access Journals (Sweden)

    Yu.V. Vorona

    2014-12-01

    Full Text Available The technique for development and reduction of discrete dynamics models of frames is presented. Construction of the models is carried out using finite element method, generalized coordinates and tools of modern computer software. Parametric resonance in a statically indeterminate frame caused by external excitations is investigated. Main instability domains of the frame are determined.

  12. Device measures static friction of magnetic tape

    Science.gov (United States)

    Cole, P. T.

    1967-01-01

    Device measures the coefficient of static friction of magnetic tape over a range of temperatures and relative humidities. It uses a strain gage to measure the force of friction between a reference surface and the tape drawn at a constant velocity of approximately 0.0001 inch per second relative to the reference surface.

  13. Energy consumption in static muscle contraction

    NARCIS (Netherlands)

    Koerhuis, CL; Hof, AL; van der Heide, F.M.

    Energy consumption during static contraction of the human triceps surae muscles was studied in 11 healthy subjects. The subjects had to stand intermittently on the left and then right foot at different frequencies (for periods of 15 s, 10 s or 5 s), first on the whole foot and then on the forefoot.

  14. Static validation of licence conformance policies

    DEFF Research Database (Denmark)

    Hansen, Rene Rydhof; Nielson, Flemming; Nielson, Hanne Riis

    2008-01-01

    Policy conformance is a security property gaining importance due to commercial interest like Digital Rights Management. It is well known that static analysis can be used to validate a number of more classical security policies, such as discretionary and mandatory access control policies, as well...

  15. Narrative Finality

    Directory of Open Access Journals (Sweden)

    Armine Kotin Mortimer

    1981-01-01

    Full Text Available The cloturai device of narration as salvation represents the lack of finality in three novels. In De Beauvoir's Tous les hommes sont mortels an immortal character turns his story to account, but the novel makes a mockery of the historical sense by which men define themselves. In the closing pages of Butor's La Modification , the hero plans to write a book to save himself. Through the thrice-considered portrayal of the Paris-Rome relationship, the ending shows the reader how to bring about closure, but this collective critique written by readers will always be a future book. Simon's La Bataille de Pharsale , the most radical attempt to destroy finality, is an infinite text. No new text can be written. This extreme of perversion guarantees bliss (jouissance . If the ending of De Beauvoir's novel transfers the burden of non-final world onto a new victim, Butor's non-finality lies in the deferral to a future writing, while Simon's writer is stuck in a writing loop, in which writing has become its own end and hence can have no end. The deconstructive and tragic form of contemporary novels proclaims the loss of belief in a finality inherent in the written text, to the profit of writing itself.

  16. Context-dependent concurrent adaptation to static and moving targets.

    Directory of Open Access Journals (Sweden)

    Maria N Ayala

    Full Text Available Is the neural control of movements towards moving targets independent to that of static targets? In the following experiments, we used a visuomotor rotation adaptation paradigm to examine the extent to which adapting arm movements to static targets generalize to that of moving targets (i.e. pursuit or tracking. In the first and second experiments, we showed that adaptation to perturbed tracking movements generalizes to reaching movements; reach aftereffects following perturbed tracking were about half the size (≈9° of those produced following reach training (≈ 19°. Given these findings, in the final experiment we associated opposing perturbations (-30° and +30° with either reaching or tracking movements and presented them within the same experimental block to determine whether these contexts allow for dual adaptation. We found that the group that experienced opposing perturbations was able to reduce both reaching and tracking errors, as well as produce reach aftereffects following dual training of ≈7°, which were substantially smaller than those produced when reach training was not concurrent with tracking training. This reduction in reach aftereffects is consistent with the extent of the interference from tracking training as measured by the reach aftereffects produced when only that condition was performed. These results suggest partial, but not complete, overlap in the learning processes involved in the acquisition of tracking and reaching movements.

  17. Common arm comparative outcomes analysis of phase 3 trials of cisplatin + irinotecan versus cisplatin + etoposide in extensive stage small cell lung cancer: final patient-level results from Japan Clinical Oncology Group 9511 and Southwest Oncology Group 0124.

    Science.gov (United States)

    Lara, Primo N; Chansky, Kari; Shibata, Taro; Fukuda, Haruhiko; Tamura, Tomohide; Crowley, John; Redman, Mary W; Natale, Ronald; Saijo, Nagahiro; Gandara, David R

    2010-12-15

    Southwest Oncology Group 0124 was a large North American phase 3 trial that failed to confirm a survival benefit for cisplatin/irinotecan over cisplatin/etoposide in patients with extensive stage small cell lung cancer (SCLC). These results were contrary to Japan Clinical Oncology Group 9511, a phase 3 trial exclusively in Japanese patients. Because 0124 and 9511 used identical treatment regimens and similar eligibility criteria, patient-level data were pooled from both trials, and a common arm analysis was performed to explore potential reasons for the divergent results. Patients with documented extensive stage SCLC and adequate end-organ function were randomized to intravenously receive either cisplatin 60 mg/m(2) Day 1 + irinotecan 60 mg/m(2) Days 1, 8, and 15 every 4 weeks or cisplatin 80 mg/m(2) Day 1 + etoposide 100 mg/m(2) Days 1-3 every 3 weeks. Demographic and outcome data were compared among 805 patients enrolled in 9511 and 0124 receiving identical treatment using a logistic model adjusted for age, sex, and performance status (PS). Of 671 patients in 0124, 651 eligible patients were included, as were all 154 patients from 9511. Significant differences in sex and PS distribution as well as toxicity were seen between trials. There were also significant differences in response rates (87% vs 60%, Pglobalization, warrant: 1) consideration of differential patient characteristics and outcomes among populations receiving identical therapy; 2) utilization of the common arm model in prospective trials; and 3) inclusion of pharmacogenomic correlates in cancer trials where ethnic/racial differences in drug disposition are expected. Copyright © 2010 American Cancer Society.

  18. Final Report

    Energy Technology Data Exchange (ETDEWEB)

    J. Toulouse

    2012-04-05

    The purpose of this project was to better understand the 'Multiscale Dynamics of Relaxor Ferroelectrics'. The output of the project is summarized in the narrative. The results of the work were presented at a number of different conferences and four papers were written, the references to which are also indicated in the report and which have also been uploaded on e-link. The multiscale dynamics of relaxors was clearly identified in the three characteristic temperatures that were identified. In particular, we were the first group to identify an intermediate temperature, T*, at which the correlations between off-center ions in relaxor cross-over from being dynamic to being static and giving rise to the characteristic relaxor behavior in the dielectric constant. Other groups have now confirmed the existence of such an intermediate temperature. We also made and reported two other observations: (1) a coherent interference phenomena (EIT-like effect) near the transition of several relaxors, which provides information on the nature and mechanism of the transition; and (2) in a similar way, inelastic neutron scattering results were interpreted as resonant scattering of acoustic phonons by localized modes in polar nanodomains. In parallel with the neutron scattering work, we also developed a theory of the scattering of phonons by the above localized modes. The theoretical development is very formal at this point and did not allow an easy comparison with the experimental results. This work is in progress.

  19. Characterisation of static and dynamic responses of natural rubber bio-composites

    Science.gov (United States)

    Kamaruddin, S.; Chai, A. B.; Lim, C. L.; Ho, J.-H.

    2017-10-01

    Characterisation of static and dynamic behavioural are presented in this study of hybrid filled natural rubber. The hybrid filler consists of a combination of oil palm ash (OPA) and egg shell powder (ESP). Testing on the samples are conducted in three different aspects namely static compression testing, time dependent stress relaxation testing in compression and dynamic compression testing. Mechanical properties such as the static stiffnesses, hysteresis loss ratios, stress relaxation responses, dynamic stiffnesses, phase angles and damping ratios are reported. The static stiffness values of the hybrid filled rubber, although lower than rubber filled carbon black, presented potential if the ESP content were to be increased. The stress relaxation responses lacked consistency in the uploading stages but were fairly consistent in the unloading stages where the relaxation was close to that of rubber filled carbon black. The dynamic properties appear to be no significant improvement over that of rubber filled carbon black filled. All hybrid filled rubber samples conformed to general dynamic properties of viscoelastic material and did not display any unexpected behaviour. Collectively, there is a trend of improvement with increasing ESP content but no prominent improvement over rubber filled carbon black is observed.

  20. Kinematics/statics analysis of a novel serial-parallel robotic arm with hand

    International Nuclear Information System (INIS)

    Lu, Yi; Dai, Zhuohong; Ye, Nijia; Wang, Peng

    2015-01-01

    A robotic arm with fingered hand generally has multi-functions to complete various complicated operations. A novel serial-parallel robotic arm with a hand is proposed and its kinematics and statics are studied systematically. A 3D prototype of the serial-parallel robotic arm with a hand is constructed and analyzed by simulation. The serial-parallel robotic arm with a hand is composed of an upper 3RPS parallel manipulator, a lower 3SPR parallel manipulator and a hand with three finger mechanisms. Its kinematics formulae for solving the displacement, velocity, acceleration of are derived. Its statics formula for solving the active/constrained forces is derived. Its reachable workspace and orientation workspace are constructed and analyzed. Finally, an analytic example is given for solving the kinematics and statics of the serial-parallel robotic arm with a hand and the analytic solutions are verified by a simulation mechanism.

  1. Kinematics/statics analysis of a novel serial-parallel robotic arm with hand

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Yi; Dai, Zhuohong; Ye, Nijia; Wang, Peng [Yanshan University, Hebei (China)

    2015-10-15

    A robotic arm with fingered hand generally has multi-functions to complete various complicated operations. A novel serial-parallel robotic arm with a hand is proposed and its kinematics and statics are studied systematically. A 3D prototype of the serial-parallel robotic arm with a hand is constructed and analyzed by simulation. The serial-parallel robotic arm with a hand is composed of an upper 3RPS parallel manipulator, a lower 3SPR parallel manipulator and a hand with three finger mechanisms. Its kinematics formulae for solving the displacement, velocity, acceleration of are derived. Its statics formula for solving the active/constrained forces is derived. Its reachable workspace and orientation workspace are constructed and analyzed. Finally, an analytic example is given for solving the kinematics and statics of the serial-parallel robotic arm with a hand and the analytic solutions are verified by a simulation mechanism.

  2. Static vs. Dynamic Acute Stretching Effect on Quadriceps Muscle Activity during Soccer Instep Kicking

    Science.gov (United States)

    Amiri-Khorasani, Mohammadtaghi; Kellis, Eleftherios

    2013-01-01

    The purpose of this study was to compare the effects of static and dynamic stretching on quadriceps muscle activation during maximal soccer instep kicking. The kicking motion of twelve male college soccer players (body height: 174.66 ± 5.01 cm; body mass: 72.83 ± 4.83 kg; age: 18.83 ± 0.75 years) was captured using six synchronized high-speed infra-red cameras whilst electromyography (EMG) signals from vastus medialis (VM), lateralis (VL) and rectus femoris (RF) were recorded before and after static or dynamic stretching. Analysis of variance designs showed a higher increase in knee extension angular velocity (9.65% vs. −1.45%, p stretching exercises. Based on these results, it could be suggested that dynamic stretching is probably more effective in increasing quadriceps muscle activity and knee extension angular velocity during the final swing phase of a maximal soccer instep kick than static stretching. PMID:24511339

  3. Final Report

    DEFF Research Database (Denmark)

    Heiselberg, Per; Brohus, Henrik; Nielsen, Peter V.

    This final report for the Hybrid Ventilation Centre at Aalborg University describes the activities and research achievement in the project period from August 2001 to August 2006. The report summarises the work performed and the results achieved with reference to articles and reports published...

  4. Future-based Static Analysis of Message Passing Programs

    Directory of Open Access Journals (Sweden)

    Wytse Oortwijn

    2016-06-01

    Full Text Available Message passing is widely used in industry to develop programs consisting of several distributed communicating components. Developing functionally correct message passing software is very challenging due to the concurrent nature of message exchanges. Nonetheless, many safety-critical applications rely on the message passing paradigm, including air traffic control systems and emergency services, which makes proving their correctness crucial. We focus on the modular verification of MPI programs by statically verifying concrete Java code. We use separation logic to reason about local correctness and define abstractions of the communication protocol in the process algebra used by mCRL2. We call these abstractions futures as they predict how components will interact during program execution. We establish a provable link between futures and program code and analyse the abstract futures via model checking to prove global correctness. Finally, we verify a leader election protocol to demonstrate our approach.

  5. Static leaching of uraniferous shales with countercurrent circuits

    International Nuclear Information System (INIS)

    Cordero, G.; Villarrubia, M.; Hernandez, J.

    1973-01-01

    We test different amounts of acid and the way of adding it in order to obtain the solubilization of uranium in static leaching. We also test the effects of the temperature. Finally we show the tests of solvent extraction considering the most important variables in it . In leaching we must work with 32 kg/t of acid and 40 d in order to obtain uraniums solubilization over 80%, The pregnant liquors have a high concentration of silica and we must use low organic liquid ( ≤ 3,5 % in amine) and fit the acidity of the pregnant Solutions to 4-8 g H 2 SO 4 /I. We show the economy of the process. (Author)

  6. Understanding cancer staging

    Science.gov (United States)

    ... detailed information about the cancer stage. TNM Staging System The most common system for staging cancer in the form of solid tumor is the TNM system. Most providers and cancer centers use it to stage ...

  7. Analysis of dynamic and static filtration and determination of MUD cake parameters

    Energy Technology Data Exchange (ETDEWEB)

    Calcada, L.A.; Scheid, C.M.; Araujo, C.A.O. de [Universidade Federal Rural do Rio de Janeiro (UFRRJ), Seropedica, RJ (Brazil). Dept. de Engenharia Quimica], e-mail: calcada@ufrrj.br; Waldmann, A.T.A.; Martins, A.L. [Petroleo Brasileiro S.A. (CENPES/PETROBRAS), Rio de Janeiro, RJ (Brazil). Centro de Pesquisas

    2011-07-15

    Drilling operations around the world employ a concept called overbalance. During this process, it is well known that dynamic and static filtration can occur. Thin filter cakes and low fluid-invasion rates are extremely desirable to promote optimal logging conditions and permeability return. The aim of this work was to compare the different behavior between dynamic and static filtration in drilling wells. To investigate the filtration process of Newtonian suspensions, we built a dynamic and static filtration loop with which we acquired experimental filtration volume data as a function of time. The filtration loop included a tank mixer where a Newtonian aqueous calcium carbonate polydisperse suspension was homogenized. The suspension was pumped through tubes to a dynamic or a static filtration cell. We validated a theoretical model based on Darcy's law and on mass conservation proposed by Ferreira and Massarani (2005). That model predicted mud cake buildup and filtrate flow rate for Newtonian suspensions. Relying on both models and the experimental data, filter cake parameters were calculated. We discuss, based on these parameters, the effects of the filtration configuration in dynamic and static modes. Finally, we generalized Ferreira and Massarani's model (2005) for procedures involving non-Newtonian suspensions. This new model can predict dynamic filtration and fluid invasion for non-Newtonian suspensions as drilling fluids. (author)

  8. Safety prediction for basic components of safety-critical software based on static testing

    International Nuclear Information System (INIS)

    Son, H.S.; Seong, P.H.

    2000-01-01

    The purpose of this work is to develop a safety prediction method, with which we can predict the risk of software components based on static testing results at the early development stage. The predictive model combines the major factor with the quality factor for the components, which are calculated based on the measures proposed in this work. The application to a safety-critical software system demonstrates the feasibility of the safety prediction method. (authors)

  9. Safety prediction for basic components of safety critical software based on static testing

    International Nuclear Information System (INIS)

    Son, H.S.; Seong, P.H.

    2001-01-01

    The purpose of this work is to develop a safety prediction method, with which we can predict the risk of software components based on static testing results at the early development stage. The predictive model combines the major factor with the quality factor for the components, both of which are calculated based on the measures proposed in this work. The application to a safety-critical software system demonstrates the feasibility of the safety prediction method. (authors)

  10. Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Stinis, Panos [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-08-07

    This is the final report for the work conducted at the University of Minnesota (during the period 12/01/12-09/18/14) by PI Panos Stinis as part of the "Collaboratory on Mathematics for Mesoscopic Modeling of Materials" (CM4). CM4 is a multi-institution DOE-funded project whose aim is to conduct basic and applied research in the emerging field of mesoscopic modeling of materials.

  11. Static devices with new permanent magnets

    International Nuclear Information System (INIS)

    Chavanne, J.; Laforest, J.; Pauthenet, R.

    1987-01-01

    The high remanence and coercivity of the new permanent magnet materials are of special interest in the static applications. High ordering temperature and are uniaxial anisotropy at the origin of their good permanent magnet properties are obtained in rare earth-transition metal compounds. Binary SmCo/sub 5/ and Sm/sub 2/Co/sub 17/ and ternary Nd/sub 2/Fe/sub 14/B compounds are the basis materials of the best permanent magnets. new concepts of calculations of static devices with these magnets can be applied: the magnetization can be considered as ridig, the density of the surface Amperian current is constant, the relative permeability is approximately 1 and the induction calculations are linear. Examples of hexapoles with Sm-Co and NdFeB magnets are described and the performances are compared. The problems of temperature behavior and corrosion resistance are underlined

  12. Variational approach for static mirror structures

    Energy Technology Data Exchange (ETDEWEB)

    Kuznetsov, E. A. [P.N. Lebedev Physical Institute RAS, 53 Leninsky Ave., 119991 Moscow (Russian Federation); Space Research Institute RAS, 84/32 Profsoyuznaya str., 117997 Moscow (Russian Federation); L.D. Landau Institute for Theoretical Physics RAS, 2 Kosygin str., 119334 Moscow (Russian Federation); Passot, T.; Sulem, P. L. [UNS, CNRS, Observatoire de la Côte d' Azur, CS 34229, 06304 Nice Cedex 4 (France); Ruban, V. P. [L.D. Landau Institute for Theoretical Physics RAS, 2 Kosygin str., 119334 Moscow (Russian Federation)

    2015-04-15

    Anisotropic static plasma equilibria where the parallel and perpendicular pressures are only functions of the amplitude of the local magnetic field are shown to be amenable to a variational principle with a free energy density given by the parallel tension. This approach is used to demonstrate that two-dimensional small-amplitude static magnetic holes constructed from a Grad-Shafranov type equation slightly below the (subcritical) mirror instability threshold identify with lump solitons of KPII equation, but turn out to be unstable. Differently, large-amplitude magnetic structures, which are stable as they realize a minimum of the free energy, are computed using a gradient method within two-dimensional numerical simulations where the regularizing effect of finite Larmor radius corrections is retained. Interestingly, these structures transform from stripes to bubbles when the angle of the magnetic field with the coordinate plane is increased.

  13. Static Checking of Interrupt-driven Software

    DEFF Research Database (Denmark)

    Brylow, Dennis; Damgaard, Niels; Palsberg, Jens

    2001-01-01

    Resource-constrained devices are becoming ubiquitous. Examples include cell phones, palm pilots, and digital thermostats. It can be difficult to fit required functionality into such a device without sacrificing the simplicity and clarity of the software. Increasingly complex embedded systems...... require extensive brute-force testing, making development and maintenance costly. This is particularly true for system components that are written in assembly language. Static checking has the potential of alleviating these problems, but until now there has been little tool support for programming...... at the assembly level. In this paper we present the design and implementation of a static checker for interrupt-driven Z86-based software with hard real-time requirements. For six commercial microcontrollers, our checker has produced upper bounds on interrupt latencies and stack sizes, as well as verified...

  14. Static compliance of foundations of arbitrary shape

    International Nuclear Information System (INIS)

    Hejazi, M.; Nemat-Nasser, S.

    1982-01-01

    The calculation of the compliance matric of foundations is an essential first step in the static or dynamics analysis of soil-foundation interaction problems. An effective numerical method is presented for accurate computation of the static compliance of rigid foundations with arbitrary shapes, which rest on an elastic half-space and are subjected to vertical and horizontal loads, as well as tilting and torsional moments. In this method the contacting area is subbivided into a finite number of 'equivalent' circular elements, which leads to solutions in a rather simple form that require minimal numerical computations. The results are illustrated by calculating the overall compliances of foundations of various geometries, and these are compared with results obtained by means of another, more elaborate, method. (orig.)

  15. Model of the static universe within GR

    Energy Technology Data Exchange (ETDEWEB)

    Karbanovski, V. V., E-mail: karbanovski_v_v@mail.ru; Tarasova, A. S.; Salimova, A. S.; Bilinskaya, G. V.; Sumbulov, A. N. [Murmansk State Pedagogical University (Russian Federation)

    2011-01-15

    Within GR, the problems of the Robertson-Walker universe are discussed. The approach based on transition to a nondiagonal line element is suggested. Within the considered approach, the static universe model is investigated. The possibility of constructing scenarios without an initial singularity and 'exotic' matter is discussed. Accordance of the given model to the properties of the observable universe is discussed.

  16. Static three- and four-quark potentials

    CERN Document Server

    Alexandrou, C; Tsapalis, A; Forcrand, Ph.de

    2002-01-01

    We present results for the static three- and four-quark potentials in SU(3) and SU(4) respectively. Using a variational approach, combined with multi-hit for the time-like links, we determine the ground state of the baryonic string with sufficient accuracy to test the $Y-$ and $\\Delta-$ ans\\"atze for the baryonic Wilson area law. Our results favor the $\\Delta$ ansatz, where the potential is the sum of two-body terms.

  17. Predicting environmental restoration activities through static simulation

    International Nuclear Information System (INIS)

    Ross, T.L.; King, D.A.; Wilkins, M.L.; Forward, M.F.

    1994-12-01

    This paper discusses a static simulation model that predicts several performance measures of environmental restoration activities over different remedial strategies. Basic model operation consists of manipulating and processing waste streams via selecting and applying remedial technologies according to the strategy. Performance measure prediction is possible for contaminated soil, solid waste, surface water, groundwater, storage tank, and facility sites. Simulations are performed for the U.S. Department of Energy in support of its Programmatic Environmental Impact Statement

  18. Optimal Mutation Rates on Static Fitness Landscpes

    OpenAIRE

    Nilsson, M.

    2000-01-01

    We study the evolution of mutation rates for an asexual population living on a static fitness landscape, consisting of multiple peaks forming an evolutionary staircase. The optimal mutation rate is found by maximizing the diffusion towards higher fitness. Surprisingly the optimal genomic copying fidelity is given by Q = e^(-1/ln(n)) (where n is the genome length), independent of all other parameters in the model. Simulations confirm this theoretical result. We also discuss the relation betwee...

  19. Adding Traits to (Statically Typed) Languages

    OpenAIRE

    Nierstrasz, Oscar; Ducasse, Stéphane; Reichhart, Stefan; Schärli, Nathanael

    2005-01-01

    Traits offer a fine-grained mechanism for composing classes in object-oriented languages from reusable components, while avoiding the fragility problems introduced by multiple inheritance and mixins. Although traits were developed in the context of dynamically typed languages, they would also offer clear benefits for statically typed languages like Java and C#. This report summarizes the issues raised when integrating traits into such languages. We examine traits in the context of the statica...

  20. Supporting software inspection with static profiling

    OpenAIRE

    Boogerd, C.; Moonen, L.

    2009-01-01

    Static software checking tools are useful as an additional automated software inspection step that can easily be integrated in the development cycle and assist in creating secure, reliable and high quality code. However, an often quoted disadvantage of these tools is that they generate an inordinate number of warnings, including many false positives due to the use of approximate analysis techniques. This information overload effectively limits their usefulness. In this paper we present ELAN, ...

  1. Prioritizing Software Inspection Results using Static Profiling

    OpenAIRE

    Boogerd, Cathal; Moonen, Leon

    2006-01-01

    Static software checking tools are useful as an additional automated software inspection step that can easily be integrated in the development cycle and assist in creating secure, reliable and high quality code. However, an often quoted disadvantage of these tools is that they generate an overly large number of warnings, including many false positives due to the approximate analysis techniques. This information overload effectively limits their usefulness. In this paper we present ELAN, a tec...

  2. Proximity and Innovation: From Statics to Dynamics

    OpenAIRE

    Pierre-Alexandre Balland; Ron Boschma; Koen Frenken

    2013-01-01

    Despite theoretical and empirical advances, the proximity framework has remained essentially static in that the given proximity between actors explains the extent to which they interact in knowledge networks and profit from such interactions. We propose a dynamic extension of the proximity framework of Boschma in which we account for co-evolutionary dynamics between knowledge networking and proximity. For each proximity dimension, we describe how proximities might increase over time as a resu...

  3. Plate shell structures - statics and stability

    DEFF Research Database (Denmark)

    Almegaard, Henrik

    2008-01-01

    This paper describes the basic structural system, statics and spatial stability of plate shells. The structural system can be considered as a single layer of planar elements, where each element only transfers in-plane (membrane) forces to its neighbouring elements. External out-of-plane loads...... system is dual to that of a spatial truss system, which means the stringer system [1] can be applied to plate-shell structures....

  4. Structural Encoding of Static Single Assignment Form

    DEFF Research Database (Denmark)

    Gal, Andreas; Probst, Christian; Franz, Michael

    2005-01-01

    Static Single Assignment (SSA) form is often used as an intermediate representation during code optimization in Java Virtual Machines. Recently, SSA has successfully been used for bytecode verification. However, constructing SSA at the code consumer is costly. SSAbased mobile code transport formats...... Java bytecode. While the resulting bytecode sequence can still be directly executed by traditional Virtual Machines, our novel VM can infer SSA form and confirm its safety with virtually no overhead....

  5. Comparing numerically exact and modelled static friction

    Directory of Open Access Journals (Sweden)

    Krengel Dominik

    2017-01-01

    Full Text Available Currently there exists no mechanically consistent “numerically exact” implementation of static and dynamic Coulomb friction for general soft particle simulations with arbitrary contact situations in two or three dimension, but only along one dimension. We outline a differential-algebraic equation approach for a “numerically exact” computation of friction in two dimensions and compare its application to the Cundall-Strack model in some test cases.

  6. A field theoretic model for static friction

    OpenAIRE

    Mahyaeh, I.; Rouhani, S.

    2013-01-01

    We present a field theoretic model for friction, where the friction coefficient between two surfaces may be calculated based on elastic properties of the surfaces. We assume that the geometry of contact surface is not unusual. We verify Amonton's laws to hold that friction force is proportional to the normal load.This model gives the opportunity to calculate the static coefficient of friction for a few cases, and show that it is in agreement with observed values. Furthermore we show that the ...

  7. ARC Code TI: Inference Kernel for Open Static Analyzers (IKOS)

    Data.gov (United States)

    National Aeronautics and Space Administration — IKOS is a C++ library designed to facilitate the development of sound static analyzers based on Abstract Interpretation. Specialization of a static analyzer for an...

  8. Death and transfiguration in static Staphylococcus epidermidis cultures.

    Directory of Open Access Journals (Sweden)

    Christoph Schaudinn

    Full Text Available The overwhelming majority of bacteria live in slime embedded microbial communities termed biofilms, which are typically adherent to a surface. However, when several Staphylococcus epidermidis strains were cultivated in static liquid cultures, macroscopic aggregates were seen floating within the broth and also sedimented at the test tube bottom. Light- and electron microscopy revealed that early-stage aggregates consisted of bacteria and extracellular matrix, organized in sheet-like structures. Perpendicular under the sheets hung a network of periodically arranged, bacteria-associated strands. During the extended cultivation, the strands of a subpopulation of aggregates developed into cross-connected wall-like structures, in which aligned bacteria formed the walls. The resulting architecture had a compartmentalized appearance. In late-stage cultures, the wall-associated bacteria disintegrated so that, henceforth, the walls were made of the coalescing remnants of lysed bacteria, while the compartment-like organization remained intact. At the same time, the majority of strand-containing aggregates with associated culturable bacteria continued to exist. These observations indicate that some strains of Staphylococcus epidermidis are able to build highly sophisticated structures, in which a subpopulation undergoes cell lysis, presumably to provide continued access to nutrients in a nutrient-limited environment, whilst maintaining structural integrity.

  9. What Sexual Recidivism Rates Are Associated With Static-99R and Static-2002R Scores?

    Science.gov (United States)

    Hanson, R Karl; Thornton, David; Helmus, Leslie-Maaike; Babchishin, Kelly M

    2016-04-01

    Empirical actuarial risk tools are routinely used to assess the recidivism risk of adult sexual offenders. Compared with other forms of risk assessment, one advantage of actuarial risk tools is that they provide recidivism rate estimates. Previous research, however, suggests that there is considerable variability in the recidivism rates associated with the most commonly used sexual offender risk assessment tools (Static-99/R, Static-2002/R). The current study examined the extent to which the variability in the recidivism rates across 21 Static-99R studies (N = 8,805) corresponded to the normative groups proposed by the STATIC development group (routine, treatment, high risk/high need). We found strong evidence that routine (i.e., complete) samples were, on average, less likely to reoffend with a sexual offense than offenders in the high-risk/high-need samples (i.e., those explicitly preselected on risk-relevant variables external to STATIC scales). The differences between routine/complete and high-risk/high-need samples, however, were only consistently observed for offenders with low or moderate scores; for offenders with high STATIC scores, the 5-year sexual recidivism rates for these two groups were not meaningfully different. There was only limited evidence to support treatment samples as a distinct sample type; consequently, the use of separate normative tables for treatment samples is not recommended. The current results reinforce the value of regularly updating the norms for empirical actuarial risk tools. Options are discussed on how STATIC scores could be used to inform recidivism rates estimates in applied assessments. © The Author(s) 2015.

  10. Common arm comparative outcomes analysis of phase III trials of cisplatin + irinotecan vs. cisplatin + etoposide in extensive stage small cell lung cancer: Final patient-level results from JCOG 9511 and SWOG 0124

    Science.gov (United States)

    Lara, Primo N.; Chansky, Kari; Shibata, Taro; Fukuda, Haruhiko; Tamura, Tomohide; Crowley, John; Redman, Mary W.; Natale, Ronald; Saijo, Nagahiro; Gandara, David R

    2010-01-01

    Background S0124 was a large North American phase III trial that failed to confirm a survival benefit for cisplatin/irinotecan over cisplatin/etoposide in patients with extensive stage small cell lung cancer (E-SCLC). These results were contrary to J9511, a phase III trial exclusively in Japanese patients. Since S0124 and J9511 used identical treatment regimens and similar eligibility criteria, patient-level data were pooled from both trials and a “common arm” analysis was performed to explore potential reasons for the divergent results. Methods Patients with documented E-SCLC and adequate end-organ function were randomized to intravenously receive either Cisplatin 60 mg/m2 day 1 + Irinotecan 60 mg/m2 days 1, 8, & 15 every 4 weeks or Cisplatin 80 mg/m2 day 1 + Etoposide 100 mg/m2 days 1-3 every 3 weeks. Demographics and outcomes data were compared among 805 patients enrolled in J9511 and S0124 receiving identical treatment using a logistic model adjusted for age, sex, and performance status (PS). Results Of 671 patients in S0124, 651 eligible patients were included as were all 154 patients from J9511. Significant differences in sex and PS distribution as well as toxicity were seen between trials. There were also significant differences in response rates (87% vs. 60%, p<0.001) and median overall survival (12.8 vs. 9.8 months, p<0.001) when the cisplatin/irinotecan arms from both trials were compared. Conclusions Significant differences in patient demographics, toxicity, and efficacy were identified in the J9511 and S0124 populations. These results, relevant in the current era of clinical trials globalization, warrant: 1) consideration of differential patient characteristics and outcomes amongst populations receiving identical therapy; 2) utilization of the “common arm” model in prospective trials; and 3) inclusion of pharmacogenomic correlates in cancer trials where ethnic/racial differences in drug disposition are expected. PMID:20737417

  11. Processing accuracy control at the stage of CNC machines setting up for a program operation

    Directory of Open Access Journals (Sweden)

    О.I. Leshchenko

    2017-12-01

    Full Text Available The presented calculation of the parameters of shaping accuracy control makes it possible to form tool movement trajectories using the algorithms of adjustment, as early as at the stage of technological adjustment of the CNC machine operation. This opens up the possibility of wider use of internal algorithms of modern CNC machines, not only as programmers of displacement trajectories, but of correcting values as well based on experimental or analytical coefficients in mathematical models developed by the user, that take into account the vector values of the corrections for static and dynamic operating modes of the machine. Such an approach meets the requirements as to obtaining a scientifically based concept of the transition from setup to the final surface treatment by means of «trial moves and measurements» to the method of «debugging in advance» of machine tools with programmed control.

  12. 14 CFR 33.64 - Pressurized engine static parts.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Pressurized engine static parts. 33.64... engine static parts. (a) Strength. The applicant must establish by test, validated analysis, or a combination of both, that all static parts subject to significant gas or liquid pressure loads for a...

  13. 14 CFR 105.47 - Use of static lines.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Use of static lines. 105.47 Section 105.47... static lines. (a) Except as provided in paragraph (c) of this section, no person may conduct a parachute operation using a static line attached to the aircraft and the main parachute unless an assist device...

  14. Static potential for a string with a topological term

    International Nuclear Information System (INIS)

    Zaikov, R.P.; Zlatev, S.I.

    1991-01-01

    We study the static potential for a string in (2+1)-dimensional space-time with action including a topological term. An appropriate static solution is found and the corresponding potential is obtained. Such a solution does not exist beyond a critical distance between the ends of the string. The one-loop corrections to the static potential are calculated. (orig.)

  15. 30 CFR 18.67 - Static-pressure tests.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Static-pressure tests. 18.67 Section 18.67....67 Static-pressure tests. Static-pressure tests shall be conducted by the applicant on each enclosure... pressure to be applied shall be 150 pounds per square inch (gage) or one and one-half times the maximum...

  16. 14 CFR 25.1325 - Static pressure systems.

    Science.gov (United States)

    2010-01-01

    ... atmosphere through an appropriate piping system. (b) Each static port must be designed and located in such manner that the static pressure system performance is least affected by airflow variation, or by moisture... and true ambient atmospheric static pressure is not changed when the airplane is exposed to the...

  17. 14 CFR 27.1325 - Static pressure systems.

    Science.gov (United States)

    2010-01-01

    ... foreign matter does not seriously affect its accuracy. (b) Each static pressure port must be designed and... ambient atmospheric static pressure is not altered when the rotorcraft encounters icing conditions. An... reading of the altimeter when on the primary static system by more than 50 feet, a correction card must be...

  18. 30 CFR 56.6602 - Static electricity dissipation during loading.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Static electricity dissipation during loading... Explosives Extraneous Electricity § 56.6602 Static electricity dissipation during loading. When explosive material is loaded pneumatically into a blasthole in a manner that generates a static electricity hazard...

  19. 14 CFR 27.610 - Lightning and static electricity protection.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Lightning and static electricity protection....610 Lightning and static electricity protection. (a) The rotorcraft must be protected against... static electricity must— (1) Minimize the accumulation of electrostatic charge; (2) Minimize the risk of...

  20. The Static Ladder Problem with Two Sources of Friction

    Science.gov (United States)

    Bennett, Jonathan; Mauney, Alex

    2011-01-01

    The problem of a ladder leaning against a wall in static equilibrium is a classic example encountered in introductory mechanics texts. Most discussions of this problem assume that the static frictional force between the ladder and wall can be ignored. A few authors consider the case where the static friction coefficients between ladder/wall…

  1. Conclusiones finales

    OpenAIRE

    Guerrero Gaitán, Manuel

    2016-01-01

    La investigación realizada permite extraer las siguientes conclusiones finales que serán agrupadas según los principales problemas abordados: 1. En relación a las cláusulas que impiden una adecuada transferencia de tecnología, en la presente investigación se demuestra: Primero. Que las cláusulas más frecuentes recogidas en los contratos internacionales de transferencia de tecnología son: la fijación de precios, las restricciones a la investigación y adaptación de la tecnología objeto del cont...

  2. Final Report

    Energy Technology Data Exchange (ETDEWEB)

    R Paul Drake

    2004-01-12

    OAK-B135 This is the final report from the project Hydrodynamics by High-Energy-Density Plasma Flow and Hydrodynamics and Radiation Hydrodynamics with Astrophysical Applications. This project supported a group at the University of Michigan in the invention, design, performance, and analysis of experiments using high-energy-density research facilities. The experiments explored compressible nonlinear hydrodynamics, in particular at decelerating interfaces, and the radiation hydrodynamics of strong shock waves. It has application to supernovae, astrophysical jets, shock-cloud interactions, and radiative shock waves.

  3. Using Models at the Mesoscopic Scale in Teaching Physics: Two Experimental Interventions in Solid Friction and Fluid Statics

    Science.gov (United States)

    Besson, Ugo; Viennot, Laurence

    2004-01-01

    This article examines the didactic suitability of introducing models at an intermediate (i.e. mesoscopic) scale in teaching certain subjects, at an early stage. The design and evaluation of two short sequences based on this rationale will be outlined: one bears on propulsion by solid friction, the other on fluid statics in the presence of gravity.…

  4. One-stage and two-stage penile buccal mucosa urethroplasty

    Directory of Open Access Journals (Sweden)

    G. Barbagli

    2016-03-01

    Full Text Available The paper provides the reader with the detailed description of current techniques of one-stage and two-stage penile buccal mucosa urethroplasty. The paper provides the reader with the preoperative patient evaluation paying attention to the use of diagnostic tools. The one-stage penile urethroplasty using buccal mucosa graft with the application of glue is preliminary showed and discussed. Two-stage penile urethroplasty is then reported. A detailed description of first-stage urethroplasty according Johanson technique is reported. A second-stage urethroplasty using buccal mucosa graft and glue is presented. Finally postoperative course and follow-up are addressed.

  5. Investigation of vanadium catalyst regeneration stages

    International Nuclear Information System (INIS)

    Tsarev, Yu.V.; Il'in, A.P.; Shirokov, Yu.G.

    1995-01-01

    Regeneration stages of vanadium catalyst: dissolution of spent catalyst in alkaline solution of potassium vanadate, precipitation and aging of hydrosilica gel, which passed to solution, have been studied experimentally. The influence of the stages on final activity and thermal stability of regenerated contact masses has been considered. 10 refs., 4 figs., 2 tabs

  6. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Jarillo-Herrero, Pablo [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

    2017-02-07

    This is the final report of our research program on electronic transport experiments on Topological Insulator (TI) devices, funded by the DOE Office of Basic Energy Sciences. TI-based electronic devices are attractive as platforms for spintronic applications, and for detection of emergent properties such as Majorana excitations , electron-hole condensates , and the topological magneto-electric effect . Most theoretical proposals envision geometries consisting of a planar TI device integrated with materials of distinctly different physical phases (such as ferromagnets and superconductors). Experimental realization of physics tied to the surface states is a challenge due to the ubiquitous presence of bulk carriers in most TI compounds as well as degradation during device fabrication.

  7. THERMAL VACUUM TEST OF ORBITAL STATIC MOISTURE-REMOVAL FUEL CELL.

    Science.gov (United States)

    The report presents the results of a thermal vacuum chamber test of an orbital fuel cell of advanced design. The fuel cell package used a static moisture-removal system. The fuel cell , tested in the thermal vacuum chamber at Wright-Patterson AFB, gave satisfactory results. This test constituted the second and final ground qualification of this orbital fuel cell prior to orbital test. (Author)

  8. Geovisualisation as a process of creating complementary visualisations: static two-dimensional, surface three-dimensional, and interactive

    Science.gov (United States)

    Horbiński, Tymoteusz; Medyńska-Gulij, Beata

    2017-06-01

    In the following paper, geovisualisation will be applied to one spatial phenomenon and understood as a process of creating complementary visualisations: static two-dimensional, surface three-dimensional, and interactive. The central challenge that the researchers faced was to find a method of presenting the phenomenon in a multi-faceted way. The main objective of the four-stage study was to show the capacity of the contemporary software for presenting geographical space from various perspectives while maintaining the standards of cartographic presentation and making sure that the form remains attractive for the user. The correctness, effectiveness, and usefulness of the proposed approach was analysed on the basis of a geovisualisation of natural aggregate extraction in the Gniezno district in the years 2005-2015. For each of the three visualisations, the researchers planned a different range of information, different forms of graphic and cartographic presentation, different use and function, but as far as possible the same accessible databases and the same free technologies. On the basis of the final publication, the researchers pointed out the advantages of the proposed workflow and the correctness of the detailed flowchart.

  9. Experimental and FEM analysis of three carbon steel characterization under quasi-static strain rate for bumper beam application

    Directory of Open Access Journals (Sweden)

    Alemayehu Dawit Bogale

    2017-01-01

    Full Text Available This paper investigates the mechanical behavior of three selected steel materials which are considered to be the bulk material of front most bumper beam of a vehicle that is suddenly loaded in the quasi-static range. Thirty-six constant strain rate uniaxial tension tests were performed. The test was performed on a HUALONG electro-hydraulic universal testing machine at four strain rates (3.33 × 10-3,3.33 × 10-2, 3.33 × 10-1, 3. 33s-1. The FEM which is ABAQUS/CAE is used to simulate the bumper subsystem using the three selected steel. The outcome shows that ultimate tensile strength (UTS increase with an increase in strain rate and high alloy steel (HAS material has the maximum mean UTS. The FEM in the post -processing stage gives the minimum displacement and maximum strain energy for HAS material when compared to the other two materials. Finally, from both experimental and ABAQUS explicit analysis the result shows HAS material is better suit for the bumper beam application.

  10. Static Analysis of XML Transformations in Java

    DEFF Research Database (Denmark)

    Kirkegaard, Christian; Møller, Anders; Schwartzbach, Michael I.

    2004-01-01

    Abstract--XML documents generated dynamically by programs are typically represented as text strings or DOM trees. This is a low-level approach for several reasons: 1) Traversing and modifying such structures can be tedious and error prone, 2) although schema languages, e.g., DTD, allow classes...... of XML documents to be defined, there are generally no automatic mechanisms for statically checking that a program transforms from one class to another as intended. We introduce Xact, a high-level approach for Java using XML templates as a first-class data type with operations for manipulating XML values...

  11. Static Model of Cement Rotary Kiln

    Directory of Open Access Journals (Sweden)

    Omar D. Hernández-Arboleda

    2013-11-01

    Full Text Available In this paper, a static model of cement rotary kilns is proposed. The system model is obtained through polynomial series. The proposed model is contrasted with data of a real plant, where optimal results are obtained. Expected results are measured with respect to the clinker production and the combustible consumption is measured in relation with the consumption calorific. The expected result of the approach is the increase of the profitability of the factory through the decrease of the consumption of the combustible.

  12. Automatic incrementalization of Prolog based static analyses

    DEFF Research Database (Denmark)

    Eichberg, Michael; Kahl, Matthias; Saha, Diptikalyan

    2007-01-01

    Modem development environments integrate various static analyses into the build process. Analyses that analyze the whole project whenever the project changes are impractical in this context. We present an approach to automatic incrementalization of analyses that are specified as tabled logic...... programs and evaluated using incremental tabled evaluation, a technique for efficiently updating memo tables in response to changes in facts and rules. The approach has been implemented and integrated into the Eclipse IDE. Our measurements show that this technique is effective for automatically...

  13. Defects in Static Elasticity of Quasicrystals

    Directory of Open Access Journals (Sweden)

    Qin Xu

    2017-12-01

    Full Text Available A review on mathematical elasticity of quasicrystals is given. In this review, the focus is on various defects of quasicrystals. Dislocation and crack are two classes of typical topological defects, while their existence has great influence on the mechanical behavior of quasicrystals. The analytic and numerical solutions of dislocations and crack in quasicrystals are the core of the static and dynamic elasticity theory, and this paper gives a comprehensive review on the solutions for dislocations and crack with different configurations in different various important quasicrystalline systems. We review some results in linear elasticity of quasicrystals, referring to different boundary value problems. We also add some new achievements.

  14. Monotone Comparative Statics for the Industry Composition

    DEFF Research Database (Denmark)

    Laugesen, Anders Rosenstand; Bache, Peter Arendorf

    2015-01-01

    We let heterogeneous firms face decisions on a number of complementary activities in a monopolistically-competitive industry. The endogenous level of competition and selection regarding entry and exit of firms introduces a wedge between monotone comparative statics (MCS) at the firm level and MCS...... for the industry composition. The latter phenomenon is defined as first-order stochastic dominance shifts in the equilibrium distributions of all activities across active firms. We provide sufficient conditions for MCS at both levels of analysis and show that we may have either type of MCS without the other...

  15. Compiler-assisted static checkpoint insertion

    Science.gov (United States)

    Long, Junsheng; Fuchs, W. K.; Abraham, Jacob A.

    1992-01-01

    This paper describes a compiler-assisted approach for static checkpoint insertion. Instead of fixing the checkpoint location before program execution, a compiler enhanced polling mechanism is utilized to maintain both the desired checkpoint intervals and reproducible checkpoint 1ocations. The technique has been implemented in a GNU CC compiler for Sun 3 and Sun 4 (Sparc) processors. Experiments demonstrate that the approach provides for stable checkpoint intervals and reproducible checkpoint placements with performance overhead comparable to a previously presented compiler assisted dynamic scheme (CATCH) utilizing the system clock.

  16. Static analysis of software the abstract interpretation

    CERN Document Server

    Boulanger, Jean-Louis

    2013-01-01

    The existing literature currently available to students and researchers is very general, covering only the formal techniques of static analysis. This book presents real examples of the formal techniques called ""abstract interpretation"" currently being used in various industrial fields: railway, aeronautics, space, automotive, etc. The purpose of this book is to present students and researchers, in a single book, with the wealth of experience of people who are intrinsically involved in the realization and evaluation of software-based safety critical systems. As the authors are people curr

  17. Approach to Operational Experimental Estimation of Static Stresses of Elements of Mechanical Structures

    Science.gov (United States)

    Sedov, A. V.; Kalinchuk, V. V.; Bocharova, O. V.

    2018-01-01

    The evaluation of static stresses and strength of units and components is a crucial task for increasing reliability in the operation of vehicles and equipment, to prevent emergencies, especially in structures made of metal and composite materials. At the stage of creation and commissioning of structures to control the quality of manufacturing of individual elements and components, diagnostic control methods are widely used. They are acoustic, ultrasonic, X-ray, radiation methods and others. The using of these methods to control the residual life and the degree of static stresses of units and parts during operation is fraught with great difficulties both in methodology and in instrumentation. In this paper, the authors propose an effective approach of operative control of the degree of static stresses of units and parts of mechanical structures which are in working condition, based on recording the changing in the surface wave properties of a system consisting of a sensor and a controlled environment (unit, part). The proposed approach of low-frequency diagnostics of static stresses presupposes a new adaptive-spectral analysis of a surface wave created by external action (impact). It is possible to estimate implicit stresses of structures in the experiment due to this approach.

  18. Prostate cancer staging

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/patientinstructions/000397.htm Prostate cancer staging To use the sharing features on this ... trials you may be able to join How Prostate Cancer Staging is Done Initial staging is based on ...

  19. Research and development of methods and technologies for CO2 capture in fossil fuel power plants and storage in geological formations in the Czech Republic, stage E2: Methods of and technologies for CO2 capture from flue gas and a draft conceptual design of 2 selected variants of a CO2 capture system for a Czech coal fired power plant unit. Final report for Stage 2. Revision 0

    International Nuclear Information System (INIS)

    Ubra, Olga

    2010-12-01

    The following topics are summarised: Aim and scope of Stage 2. List of research reports developed within Stage 2. Stage 2.1: Methods of and technologies for post-combustion CO 2 capture from the flue gas. Status of research and development worldwide. Stage 2.2: Oxyfuel method and technology. Status of research and development worldwide. Stage 2.3: Selection of a chemical absorption based method for post-combustion CO 2 separation; and Stage 2.4: Conceptual proposals for a technological solution for the selected chemical absorption based method and for application of the oxyfuel method. (P.A.)

  20. Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Webb, Robert C. [Texas A& M University; Kamon, Teruki [Texas A& M University; Toback, David [Texas A& M University; Safonov, Alexei [Texas A& M University; Dutta, Bhaskar [Texas A& M University; Dimitri, Nanopoulos [Texas A& M University; Pope, Christopher [Texas A& M University; White, James [Texas A& M University

    2013-11-18

    Overview The High Energy Physics Group at Texas A&M University is submitting this final report for our grant number DE-FG02-95ER40917. This grant has supported our wide range of research activities for over a decade. The reports contained here summarize the latest work done by our research team. Task A (Collider Physics Program): CMS & CDF Profs. T. Kamon, A. Safonov, and D. Toback co-lead the Texas A&M (TAMU) collider program focusing on CDF and CMS experiments. Task D: Particle Physics Theory Our particle physics theory task is the combined effort of Profs. B. Dutta, D. Nanopoulos, and C. Pope. Task E (Underground Physics): LUX & NEXT Profs. R. Webb and J. White(deceased) lead the Xenon-based underground research program consisting of two main thrusts: the first, participation in the LUX two-phase xenon dark matter search experiment and the second, detector R&D primarily aimed at developing future detectors for underground physics (e.g. NEXT and LZ).

  1. Leg blood flow during static exercise.

    Science.gov (United States)

    Kilbom, A; Persson, J

    1982-01-01

    Leg blood flow was studied with the constant infusion dye technique during static exercise of the thigh muscles (quadriceps) and during hand-grips at 15 and 25-30% of MVC. Blood flow and oxygen uptake in the leg increased in quadriceps exercise and reached their highest values (around 1.21/min and 165 ml/min respectively) at 25-30% of MVC, whereas leg vascular resistance decreased. Regional circulatory adaptations and the oxygen uptake - leg blood flow relationship were in close agreement with the responses found in dynamic leg exercise. In view of the marked rise in intramuscular pressure previously observed during quadriceps contractions, a restriction of blood flow and an increased vascular resistance had been expected. Involuntary activation of leg muscles other than the quadriceps may explain the finding. Contractions of the contralateral quadriceps induced a slight increase in leg blood flow, whereas hand-grips had no influence on blood flow or vascular resistance in the leg. The distribution of the cardiac output during static contractions is discussed, and it is concluded that during hand-grips the increase in blood flow is predominantly distributed to the upper part of the body.

  2. Static current profile control and RFP confinement

    International Nuclear Information System (INIS)

    Scheffel, Jan; Mirza, Ahmed A.; Schnack, Dalton D.

    2013-01-01

    Static current profile control (CPC) is shown numerically to substantially enhance plasma confinement in the reversed-field pinch (RFP). By suitable application of an auxiliary electric field and adjustment of its internal location, width and amplitude, strongly decreased levels of dynamo fluctuations are obtained. The simulations are performed using a fully non-linear, resistive magnetohydrodynamic model, including the effects of ohmic heating as well as parallel and perpendicular heat conduction along stochastic field lines. The importance of controlling the parallel current profile in the core plasma to minimize the effects of tearing modes on confinement is thus confirmed. A near three-fold increase in energy confinement is found and poloidal plasma beta increases by 30% from 0.20 to 0.27. The edge heat flux is reduced to a third of that of the conventional RFP. The high-confinement phase is interrupted here by a crash, characterized by a rapid decrease in confinement. A detailed study of the crash phase is carried out by the standard Δ′ theory and a fully resistive linearized time-spectral method; the generalized weighted residual method. The analysis suggests that the instability is caused by pressure-driven, resistive g-modes. Inclusion of anisotropic thermal conduction reduces the linear growth rates. As compared with our earlier numerical studies of CPC in the RFP, employing feedback control, the present static control scheme should be more easily implemented experimentally. (paper)

  3. Robot-Crawler: Statically Balanced Gaits

    Directory of Open Access Journals (Sweden)

    S. Parasuraman

    2012-12-01

    Full Text Available This paper presents a new statically balanced walking technique for a robot-crawler. The gait design and the control of the robot crawler aim to achieve stability while walking. This statically balanced gait has to be designed in a different fashion to a wheeled robot, as there are discrete changes in the support of the robot when its legs are lifted or placed on the ground. The stability of the robot depends on how the legs are positioned relative to the body and also on the sequence and timing with which the legs are lifted and placed. In order to reduce the risk of stability loss while walking, a measure for the robot stability (so-called stability margin is typically used in the gait and motion planning. In this paper different biological behaviours of four-legged animals are studied and mapped on a quad-legrobot-crawler. Experiments were carried out on the forward walking gaits of lizards and horses. Based on these results, the stability margins of different gaits are discussed and compared.

  4. Static viscoelasticity of biomass polyethylene composites

    Directory of Open Access Journals (Sweden)

    Keyan Yang

    Full Text Available The biomass polyethylene composites filled with poplar wood flour, rice husk, cotton stalk or corn stalk were prepared by extrusion molding. The static viscoelasticity of composites was investigated by the dynamic thermal mechanical analyzer (DMA. Through the stress-strain scanning, it is found that the linear viscoelasticity interval of composites gradually decreases as the temperature rises, and the critical stress and strain values are 0.8 MPa and 0.03% respectively. The experiment shows that as the temperature rises, the creep compliance of biomass polyethylene composites is increased; under the constant temperature, the creep compliance decreases with the increase of content of biomass and calcium carbonate. The biomass and calcium carbonate used to prepare composites as filler can improve damping vibration attenuation and reduce stress deformation of composites. The stress relaxation modulus of composites is reduced and the relaxation rate increases at the higher temperature. The biomass and calcium carbonate used to prepare composites as filler not only can reduce costs, but also can increase stress relaxation modulus and improve the size thermostability of composites. The corn stalk is a good kind of biomass raw material for composites since it can improve the creep resistance property and the stress relaxation resistance property of composites more effectively than other three kinds of biomass (poplar wood flour, rice husk and cotton stalk. Keywords: Biomass, Composites, Calcium carbonate, Static viscoelasticity, Creep, Stress relaxation

  5. Static Code Analysis with Gitlab-CI

    CERN Document Server

    Datko, Szymon Tomasz

    2016-01-01

    Static Code Analysis is a simple but efficient way to ensure that application’s source code is free from known flaws and security vulnerabilities. Although such analysis tools are often coming with more advanced code editors, there are a lot of people who prefer less complicated environments. The easiest solution would involve education – where to get and how to use the aforementioned tools. However, counting on the manual usage of such tools still does not guarantee their actual usage. On the other hand, reducing the required effort, according to the idea “setup once, use anytime without sweat” seems like a more promising approach. In this paper, the approach to automate code scanning, within the existing CERN’s Gitlab installation, is described. For realization of that project, the Gitlab-CI service (the “CI” stands for "Continuous Integration"), with Docker assistance, was employed to provide a variety of static code analysers for different programming languages. This document covers the gene...

  6. Enhanced biological nutrient removal in sequencing batch reactors operated as static/oxic/anoxic (SOA) process.

    Science.gov (United States)

    Xu, Dechao; Chen, Hongbo; Li, Xiaoming; Yang, Qi; Zeng, Tianjing; Luo, Kun; Zeng, Guangming

    2013-09-01

    An innovative static/oxic/anoxic (SOA) activated sludge process characterized by static phase as a substitute for conventional anaerobic stage was developed to enhance biological nutrient removal (BNR) with influent ammonia of 20 and 40 mg/L in R1 and R2 reactors, respectively. The results demonstrated that static phase could function as conventional anaerobic stage. In R1 lower influent ammonia concentration facilitated more polyphosphate accumulating organisms (PAOs) growth, but secondary phosphorus release occurred due to NOx(-) depletion during post-anoxic period. In R2, however, denitrifying phosphorus removal proceeded with sufficient NOx(-). Both R1 and R2 saw simultaneous nitrification-denitrification. Glycogen was utilized to drive post-denitrification with denitrification rates in excess of typical endogenous decay rates. The anoxic stirring duration could be shortened from 3 to 1.5h to avoid secondary phosphorus release in R1 and little adverse impact was found on nutrients removal in R2. Copyright © 2013 Elsevier Ltd. All rights reserved.

  7. MSC/NASTRAN DMAP Alter Used for Closed-Form Static Analysis With Inertia Relief and Displacement-Dependent Loads

    Science.gov (United States)

    1996-01-01

    Solving for the displacements of free-free coupled systems acted upon by static loads is a common task in the aerospace industry. Often, these problems are solved by static analysis with inertia relief. This technique allows for a free-free static analysis by balancing the applied loads with the inertia loads generated by the applied loads. For some engineering applications, the displacements of the free-free coupled system induce additional static loads. Hence, the applied loads are equal to the original loads plus the displacement-dependent loads. A launch vehicle being acted upon by an aerodynamic loading can have such applied loads. The final displacements of such systems are commonly determined with iterative solution techniques. Unfortunately, these techniques can be time consuming and labor intensive. Because the coupled system equations for free-free systems with displacement-dependent loads can be written in closed form, it is advantageous to solve for the displacements in this manner. Implementing closed-form equations in static analysis with inertia relief is analogous to implementing transfer functions in dynamic analysis. An MSC/NASTRAN (MacNeal-Schwendler Corporation/NASA Structural Analysis) DMAP (Direct Matrix Abstraction Program) Alter was used to include displacement-dependent loads in static analysis with inertia relief. It efficiently solved a common aerospace problem that typically has been solved with an iterative technique.

  8. Closed-form Static Analysis with Inertia Relief and Displacement-Dependent Loads Using a MSC/NASTRAN DMAP Alter

    Science.gov (United States)

    Barnett, Alan R.; Widrick, Timothy W.; Ludwiczak, Damian R.

    1995-01-01

    Solving for the displacements of free-free coupled systems acted upon by static loads is commonly performed throughout the aerospace industry. Many times, these problems are solved using static analysis with inertia relief. This solution technique allows for a free-free static analysis by balancing the applied loads with inertia loads generated by the applied loads. For some engineering applications, the displacements of the free-free coupled system induce additional static loads. Hence, the applied loads are equal to the original loads plus displacement-dependent loads. Solving for the final displacements of such systems is commonly performed using iterative solution techniques. Unfortunately, these techniques can be time-consuming and labor-intensive. Since the coupled system equations for free-free systems with displacement-dependent loads can be written in closed-form, it is advantageous to solve for the displacements in this manner. Implementing closed-form equations in static analysis with inertia relief is analogous to implementing transfer functions in dynamic analysis. Using a MSC/NASTRAN DMAP Alter, displacement-dependent loads have been included in static analysis with inertia relief. Such an Alter has been used successfully to solve efficiently a common aerospace problem typically solved using an iterative technique.

  9. Closed-form static analysis with inertia relief and displacement-dependent loads using a MSC/NASTRAN DMAP Alter

    Science.gov (United States)

    Barnett, Alan R.; Widrick, Timothy W.; Ludwiczak, Damian R.

    1995-01-01

    Solving for the displacements of free-free coupled systems acted upon by static loads is commonly performed throughout the aerospace industry. Many times, these problems are solved using static analysis with inertia relief. This solution technique allows for a free-free static analysis by balancing the applied loads with inertia loads generated by the applied loads. For some engineering applications, the displacements of the free-free coupled system induce additional static loads. Hence, the applied loads are equal to the original loads plus displacement-dependent loads. Solving for the final displacements of such systems is commonly performed using iterative solution techniques. Unfortunately, these techniques can be time-consuming and labor-intensive. Since the coupled system equations for free-free systems with displacement-dependent loads can be written in closed-form, it is advantageous to solve for the displacements in this manner. Implementing closed-form equations in static analysis with inertia relief is analogous to implementing transfer functions in dynamic analysis. Using a MSC/NASTRAN DMAP Alter, displacement-dependent loads have been included in static analysis with inertia relief. Such an Alter has been used successfully to solve efficiently a common aerospace problem typically solved using an iterative technique.

  10. Between Stage and Screen

    NARCIS (Netherlands)

    Tornqvist, Egil

    1996-01-01

    Ingmar Bergman is worldwide known as a film and stage director. Yet no-one has attempted to compare his stage and screen activities. In Between stage and screen Egil Tornqvist examines formal and thematical correspondences and differences between a number of Bergman's stage, screen, and radio

  11. Linac4: the final assembly stage is under way

    CERN Multimedia

    CERN Bulletin

    2013-01-01

    The Linac4 radiofrequency quadrupole (RFQ) module was installed at the accelerator test-stand in Building 152 last August. After an assembly phase and tests that concluded last March with the acceleration of a hydrogen beam to 3 MeV, the module has just been permanently installed in the new Linac4 tunnel (Building 400). The installation of the MEBT (Medium Energy Beam Transport) will begin shortly, followed by the start of the first Linac4 commissioning phase.     To find out more about the Linac4 RFQ module, read the previous Bulletin articles published in Nos. 21-22/2010 and 35-36/2012.

  12. The final stages of the global eradication of poliomyelitis.

    Science.gov (United States)

    Grassly, Nicholas C

    2013-08-05

    The global incidence of poliomyelitis has dropped by more than 99 per cent since the governments of the world committed to eradication in 1988. One of the three serotypes of wild poliovirus has been eradicated and the remaining two serotypes are limited to just a small number of endemic regions. However, the Global Polio Eradication Initiative (GPEI) has faced a number of challenges in eradicating the last 1 per cent of wild-virus transmission. The polio endgame has also been complicated by the recognition that vaccination with the oral poliovirus vaccine (OPV) must eventually cease because of the risk of outbreaks of vaccine-derived polioviruses. I describe the major challenges to wild poliovirus eradication, focusing on the poor immunogenicity of OPV in lower-income countries, the inherent limitations to the sensitivity and specificity of surveillance, the international spread of poliovirus and resulting outbreaks, and the potential significance of waning intestinal immunity induced by OPV. I then focus on the challenges to eradicating all polioviruses, the problem of vaccine-derived polioviruses and the risk of wild-type or vaccine-derived poliovirus re-emergence after the cessation of oral vaccination. I document the role of research in the GPEI's response to these challenges and ultimately the feasibility of achieving a world without poliomyelitis.

  13. Project MIMOSA - final stage of the satellite fabrication

    Czech Academy of Sciences Publication Activity Database

    Peřestý, Radek; Sehnal, Ladislav; Pospíšilová, Libuše

    2003-01-01

    Roč. 52, 9-12 (2003), s. 819-823 ISSN 0094-5765 R&D Projects: GA ČR GV205/96/K119 Institutional research plan: CEZ:AV0Z1003909 Keywords : MIMOSA * satellite Subject RIV: BN - Astronomy, Celestial Mechanics, Astrophysics Impact factor: 0.307, year: 2003

  14. Combining Static Analysis and Runtime Checking in Security Aspects for Distributed Tuple Spaces

    DEFF Research Database (Denmark)

    Yang, Fan; Aotani, Tomoyuki; Masuhara, Hidehiko

    2011-01-01

    Enforcing security policies to distributed systems is difficult, in particular, to a system containing untrusted components. We designed AspectKE*, an aspect-oriented programming language based on distributed tuple spaces to tackle this issue. One of the key features in AspectKE* is the program...... analysis predicates and functions that provide information on future behavior of a program. With a dual value evaluation mechanism that handles results of static analysis and runtime values at the same time, those functions and predicates enable the users to specify security policies in a uniform manner....... Our two-staged implementation strategy gathers fundamental static analysis information at load-time, so as to avoid performing all analysis at runtime. We built a compiler for AspectKE*, and successfully implemented security aspects for a distributed chat system and an electronic healthcare record...

  15. Topological characterization of static strain aging of type AISI 304 austenitic stainless steel

    International Nuclear Information System (INIS)

    Monteiro, S.N.; Miranda, P.E.V. de

    1981-01-01

    Static strain aging of type AISI 304 austenitic stainless steel was studied from room temperature up to 623K by conducting tests in which the load was held approximately constant. The aging times varied between 10s and 100h, using a plastic pre-deformation of 9%. The static strain aging of 304 steel furnished an activation energy of 23.800 cal/mol. This implies that vacancies play an important role on the aging process. The curve of the variation of the discontinuous yielding with aging time presented different stages, to which specific mathematical expressions were developed. These facts permited the conclusion that Snock type mechanisms are responsible for the aging in such conditions. (Author) [pt

  16. The extended surface forces apparatus. IV. Precision static pressure control.

    Science.gov (United States)

    Schurtenberger, E; Heuberger, M

    2011-10-01

    We report on design and performance of an extended surface forces apparatus (eSFA) built into a pressurized system. The aim of this instrument is to provide control over static pressure and temperature to facilitate direct surface force experiments in equilibrium with fluids at different loci of their phase diagram. We built an autoclave that can bear a miniature eSFA. To avoid mechanical or electrical feedtroughs the miniature apparatus uses an external surface coarse approach stage under ambient conditions. The surface separation is thus pre-adjusted to approximately ~3 μm before sliding the apparatus into the autoclave. Inside the autoclave, the surface separation can be further controlled with a magnetic drive at sub-Ångstrom precision over a 14 μm range. The autoclave pressure can then be set and maintained between 20 mbar and 170 bars with few mbar precision. The autoclave is connected to a specially designed pressurization system to precondition the fluids. The temperature can be controlled between -20 and 60 °C with few mK precision. We demonstrate the operation of the instrument in the case of gaseous or liquid carbon dioxide. Thanks to a consequent decoupling of the eSFA mechanical loop from the autoclave structure, the obtained measurement stability and reproducibility, at elevated pressures, is comparable to the one established for the conventional eSFA, operated under ambient conditions.

  17. Static Magnetic Properties of AL800 Garnet Material

    Energy Technology Data Exchange (ETDEWEB)

    Kuharik, J. [Fermilab; Madrak, R. [Fermilab; Makarov, A. [Fermilab; Pellico, W. [Fermilab; Sun, S. [Fermilab; Tan, C. Y. [Fermilab; Terechkine, I. [Fermilab

    2017-05-17

    A second harmonic tunable RF cavity is being devel-oped for the Fermilab Booster. This device, which prom-ises reduction of the particle beam loss at the injection, transition, and extraction stages, employs perpendicularly biased garnet material for frequency tuning. The required range of the tuning is significantly wider than in previously built and tested tunable RF devices. As a result, the mag-netic field in the garnet comes fairly close to the gyromag-netic resonance line at the lower end of the frequency range. The chosen design concept of a tuner for the cavity cannot ensure uniform magnetic field in the garnet mate-rial; thus, it is important to know the static magnetic prop-erties of the material to avoid significant increase in the lo-cal RF loss power density. This report summarizes studies performed at Fermilab to understand variations in the mag-netic properties of the AL800 garnet material used to build the tuner of the cavity.

  18. The extended surface forces apparatus. IV. Precision static pressure control

    Science.gov (United States)

    Schurtenberger, E.; Heuberger, M.

    2011-10-01

    We report on design and performance of an extended surface forces apparatus (eSFA) built into a pressurized system. The aim of this instrument is to provide control over static pressure and temperature to facilitate direct surface force experiments in equilibrium with fluids at different loci of their phase diagram. We built an autoclave that can bear a miniature eSFA. To avoid mechanical or electrical feedtroughs the miniature apparatus uses an external surface coarse approach stage under ambient conditions. The surface separation is thus pre-adjusted to approximately ˜3 μm before sliding the apparatus into the autoclave. Inside the autoclave, the surface separation can be further controlled with a magnetic drive at sub-Ångstrom precision over a 14 μm range. The autoclave pressure can then be set and maintained between 20 mbar and 170 bars with few mbar precision. The autoclave is connected to a specially designed pressurization system to precondition the fluids. The temperature can be controlled between -20 and 60 °C with few mK precision. We demonstrate the operation of the instrument in the case of gaseous or liquid carbon dioxide. Thanks to a consequent decoupling of the eSFA mechanical loop from the autoclave structure, the obtained measurement stability and reproducibility, at elevated pressures, is comparable to the one established for the conventional eSFA, operated under ambient conditions.

  19. Friction-induced hysteresis in quasi-static granular jamming

    Science.gov (United States)

    Bandi, Mahesh; Libal, Andras; Rivera, Michael; Ecke, Robert

    2009-11-01

    Static granular packings are usually interrogated via quasi-static measurements where the packing fraction serves as the control parameter to study the pack evolution. In the absence of externally induced vibrations (effective granular temperature), quasi-static measurements are justified because the system in question is athermal. Whereas this is true for frictionless granular packings, we experimentally demonstrate the failure of quasi-staticity for frictional packings in a quasi two-dimensional system of disks. This failure is traced to hysteretic responses in the system which shifts the critical packing fraction at which the system jams to progressively higher values as the system is repeatedly jammed and un-jammed. The shift in critical packing fraction marks the system's evolution from a Random Loose Packed (RLP) to a Random Close Packed (RCP) density. This rate of evolution is experimentally determined to depend upon the quasi-static step size and the static friction coefficient of the constituent disks in the system.

  20. Static Load Distribution in Ball Bearings

    Science.gov (United States)

    Ricci, Mario

    2010-01-01

    A numerical procedure for computing the internal loading distribution in statically loaded, single-row, angular-contact ball bearings when subjected to a known combined radial and thrust load is presented. The combined radial and thrust load must be applied in order to avoid tilting between inner and outer rings. The numerical procedure requires the iterative solution of Z + 2 simultaneous nonlinear equations - where Z is the number of the balls - to yield an exact solution for axial and radial deflections, and contact angles. Numerical results for a 218 angular-contact ball bearing have been compared with those from the literature and show significant differences in the magnitudes of the ball loads, contact angles, and the extent of the loading zone.

  1. Network Completion for Static Gene Expression Data

    Directory of Open Access Journals (Sweden)

    Natsu Nakajima

    2014-01-01

    Full Text Available We tackle the problem of completing and inferring genetic networks under stationary conditions from static data, where network completion is to make the minimum amount of modifications to an initial network so that the completed network is most consistent with the expression data in which addition of edges and deletion of edges are basic modification operations. For this problem, we present a new method for network completion using dynamic programming and least-squares fitting. This method can find an optimal solution in polynomial time if the maximum indegree of the network is bounded by a constant. We evaluate the effectiveness of our method through computational experiments using synthetic data. Furthermore, we demonstrate that our proposed method can distinguish the differences between two types of genetic networks under stationary conditions from lung cancer and normal gene expression data.

  2. Weyl curvature tensor in static spherical sources

    International Nuclear Information System (INIS)

    Ponce de Leon, J.

    1988-01-01

    The role of the Weyl curvature tensor in static sources of the Schwarzschild field is studied. It is shown that in general the contribution from the Weyl curvature tensor (the ''purely gravitational field energy'') to the mass-energy inside the body may be positive, negative, or zero. It is proved that a positive (negative) contribution from the Weyl tensor tends to increase (decrease) the effective gravitational mass, the red-shift (from a point in the sphere to infinity), as well as the gravitational force which acts on a constituent matter element of a body. It is also proved that the contribution from the Weyl tensor always is negative in sources with surface gravitational potential larger than (4/9. It is pointed out that large negative contributions from the Weyl tensor could give rise to the phenomenon of gravitational repulsion. A simple example which illustrates the results is discussed

  3. Static structure of active Brownian hard disks

    Science.gov (United States)

    de Macedo Biniossek, N.; Löwen, H.; Voigtmann, Th; Smallenburg, F.

    2018-02-01

    We explore the changes in static structure of a two-dimensional system of active Brownian particles (ABP) with hard-disk interactions, using event-driven Brownian dynamics simulations. In particular, the effect of the self-propulsion velocity and the rotational diffusivity on the orientationally-averaged fluid structure factor is discussed. Typically activity increases structural ordering and generates a structure factor peak at zero wave vector which is a precursor of motility-induced phase separation. Our results provide reference data to test future statistical theories for the fluid structure of active Brownian systems. This manuscript was submitted for the special issue of the Journal of Physics: Condensed Matter associated with the Liquid Matter Conference 2017.

  4. Construction of STACY (Static Experiment Critical Facility)

    International Nuclear Information System (INIS)

    Murakami, Kiyonobu; Onodera, Seiji; Hirose, Hideyuki

    1998-08-01

    Two critical assemblies, STACY (Static Experiment Critical Facility) and TRACY (Transient Experiment Critical Facility), were constructed in NUCEF (Nuclear Fuel Cycle Safety Engineering Research Facility) to promote researches on the criticality safety at a reprocessing facility. STACY aims at providing critical data of uranium nitrate solution, plutonium nitrate solution and their mixture while varying concentration of solution fuel, core tank shape and size and neutron reflecting condition. STACY achieved first criticality in February 1995, and passed the licensing inspection by STA (Science and Technology Agency of Japan) in May. After that a series of critical experiments commenced with 10 w/o enriched uranium solution. This report describes the outline of STACY at the end of FY 1996. (author)

  5. Orienting Paramecium with intense static magnetic fields

    Science.gov (United States)

    Valles, James M., Jr.; Guevorkian, Karine; Quindel, Carl

    2004-03-01

    Recent experiments on cell division suggest the application of intense static magnetic fields as a novel tool for the manipulation of biological systems [1]. The magnetic field appears to couple to the intrinsic anisotropies in the diamagnetic components of the cells. Here, we present measurements of the intrinsic average diamagnetic anisotropy of the whole single celled ciliate, Paramecium Caudatum. Magnetic fields, 2.5 T Paramecium Caudatum that were suspended in a density matched medium. The organisms align with their long axis parallel to the applied magnetic field. Their intrinsic diamagnetic anisotropy is 3x10-11 in cgs units. We will discuss the implications of these results for employing magnetic fields to probe the behavior of swimming Paramecium. [1] J. M. Valles, Jr. et al., Expt. Cell Res.274, 112-118 (2002).

  6. Static and dynamic friction of hierarchical surfaces.

    Science.gov (United States)

    Costagliola, Gianluca; Bosia, Federico; Pugno, Nicola M

    2016-12-01

    Hierarchical structures are very common in nature, but only recently have they been systematically studied in materials science, in order to understand the specific effects they can have on the mechanical properties of various systems. Structural hierarchy provides a way to tune and optimize macroscopic mechanical properties starting from simple base constituents and new materials are nowadays designed exploiting this possibility. This can be true also in the field of tribology. In this paper we study the effect of hierarchical patterned surfaces on the static and dynamic friction coefficients of an elastic material. Our results are obtained by means of numerical simulations using a one-dimensional spring-block model, which has previously been used to investigate various aspects of friction. Despite the simplicity of the model, we highlight some possible mechanisms that explain how hierarchical structures can significantly modify the friction coefficients of a material, providing a means to achieve tunability.

  7. Measurement of excited state static moments

    International Nuclear Information System (INIS)

    Sergolle, Henri

    Electric quadrupole and magnetic dipole moments are defined from a classical description of the nucleus and a quantum expression is given for the operators. The principal characteristics of the moment interaction with an outer electric or magnetic field are recalled. The study of the perturbed angular distributions of nuclear reaction products allows half-lives of high spin isomer states to be measured (from a few ps to several hours). The decay gamma rays present, under certain conditions, a strong anisotropy; in principle only one detector is sufficient to observe the angular distribution; coincidences are unnecessary and a high counting rate becomes possible. The measurement of the Coulomb excitation probabilities give the electric (dynamic and static) moments and indirectly quadrupolar moments; two techniques are used: the analysis of elastically and inelastically scattered particles and measurement of the deexcitation γ rays in coincidence with the scattered ions. Quadrupole moments can be measured from the precession of the angular distribution [fr

  8. Static analysis of an office desk construction

    Directory of Open Access Journals (Sweden)

    Milan Novotný

    2011-01-01

    Full Text Available The objective of the paper is a static analysis of a desk construction and the determination of its probable mechanical behaviour using Finite Element Method. The construction was modelled and numerically analysed in Autocad Inventor 2011 and the stability of the entire desk was calculated with the size and placement of the loading force based on the standards and cited literature. Possible locations and directions of the deformation were analysed and a solution for its prevention was proposed and the stability of the desk as well as the extreme position of the stand were calculated. The verification of the obtained results in an accredited furniture testing lab is planned using a prototype of the office desk.

  9. Design considerations for single-stage and two-stage pneumatic pellet injectors

    International Nuclear Information System (INIS)

    Gouge, M.J.; Combs, S.K.; Fisher, P.W.; Milora, S.L.

    1988-09-01

    Performance of single-stage pneumatic pellet injectors is compared with several models for one-dimensional, compressible fluid flow. Agreement is quite good for models that reflect actual breech chamber geometry and incorporate nonideal effects such as gas friction. Several methods of improving the performance of single-stage pneumatic pellet injectors in the near term are outlined. The design and performance of two-stage pneumatic pellet injectors are discussed, and initial data from the two-stage pneumatic pellet injector test facility at Oak Ridge National Laboratory are presented. Finally, a concept for a repeating two-stage pneumatic pellet injector is described. 27 refs., 8 figs., 3 tabs

  10. A Progression of Static Equilibrium Laboratory Exercises

    Science.gov (United States)

    Kutzner, Mickey; Kutzner, Andrew

    2013-10-01

    Although simple architectural structures like bridges, catwalks, cantilevers, and Stonehenge have been integral in human societies for millennia, as have levers and other simple tools, modern students of introductory physics continue to grapple with Newton's conditions for static equilibrium. As formulated in typical introductory physics textbooks, these two conditions appear as ΣF=0(1) and Στ=0,(2) where each torque τ is defined as the cross product between the lever arm vector r and the corresponding applied force F, τ =r×F,(3) having magnitude, τ =Frsinθ.(4) The angle θ here is between the two vectors F and r. In Eq. (1), upward (downward) forces are considered positive (negative). In Eq. (2), counterclockwise (clockwise) torques are considered positive (negative). Equation (1) holds that the vector sum of the external forces acting on an object must be zero to prevent linear accelerations; Eq. (2) states that the vector sum of torques due to external forces about any axis must be zero to prevent angular accelerations. In our view these conditions can be problematic for students because a) the equations contain the unfamiliar summation notation Σ, b) students are uncertain of the role of torques in causing rotations, and c) it is not clear why the sum of torques is zero regardless of the choice of axis. Gianino5 describes an experiment using MBL and a force sensor to convey the meaning of torque as applied to a rigid-body lever system without exploring quantitative aspects of the conditions for static equilibrium.

  11. Sensing of Static Forces with Free-Falling Nanoparticles

    OpenAIRE

    Hebestreit, Erik; Frimmer, Martin; Reimann, René; Novotny, Lukas

    2017-01-01

    Miniaturized mechanical resonators have proven to be excellent force sensors. However, they usually rely on resonant sensing schemes, and their excellent performance cannot be utilized for the detection of static forces. Here, we report on a novel static-force sensing scheme and demonstrate it using optically levitated nanoparticles in vacuum. Our technique relies on an off-resonant interaction of the particle with a weak static force, and a resonant read-out of the displacement caused by thi...

  12. Investigation of two pitot-static tubes at supersonic speeds

    Science.gov (United States)

    Hasel, Lowell E; Coletti, Donald E

    1948-01-01

    The results of tests at a Mach number of 1.94 of an ogives-nose cylindrical pitot-static tube and similar tests at Mach numbers of 1.93 and 1.62 of a service pitot-static tube to determine body static pressures and indicated Mach numbers are presented and discussed. The radial pressure distribution on the cylindrical bodies is compared with that calculated by an approximate theory.

  13. Differences of Streptococcus mutans adhesion between artificial mouth systems: a dinamic and static methods

    Directory of Open Access Journals (Sweden)

    Aryan Morita

    2016-06-01

    Full Text Available Background: Various materials have been used for treating dental caries. Dental caries is a disease that attacks hard tissues of the teeth. The initial phase of caries is a formation of bacterial biofilm, called as dental plaque. Dental restorative materials are expected for preventing secondary caries formation initiated by dental plaque. Initial bacterial adhesion is assumed to be an important stage of dental plaque formation. Bacteria that recognize the receptor for binding to the pellicle on tooth surface are known as initial bacterial colonies. One of the bacteria that plays a role in the early stage of dental plaque formation is Streptococcus mutans (S. mutans. Artificial mouth system (AMS used in bacterial biofilm research on the oral cavity provides the real condition of oral cavity and continous and intermittent supply of nutrients for bacteria. Purpose: This study aimed to compare the profile of S. mutans bacterial adhesion as the primary etiologic agent for dental caries between using static method and using artificial mouth system, a dinamic. method (AMS. Method: The study was conducted at Faculty of Dentistry and Integrated Research and testing laboratory (LPPT in Universitas Gadjah Mada from April to August 2015. Composite resin was used as the subject of this research. Twelve composite resins with a diameter of 5 mm and a width of 2 mm were divided into two groups, namely group using static method and group using dynamic method. Static method was performed by submerging the samples into a 100µl suspension of 1.5 x 108 CFU/ml S. mutans and 200µl BHI broth. Meanwhile AMS method was carried out by placing the samples at the AMS tube drained with 20 drops/minute of bacterial suspension and sterile aquadest. After 72 hours, five samples from each group were calculated for their biofilm mass using 1% crystal violet and read by a spectrofotometer with a wavelength of 570 nm. Meanwhile, one sample from each group was taken for its

  14. Fast static field CIPT mapping of unpatterned MRAM film stacks

    DEFF Research Database (Denmark)

    Kjær, Daniel; Hansen, Ole; Henrichsen, Henrik Hartmann

    2015-01-01

    Current In-Plane Tunneling (CIPT) method measures both RA and TMR, but the usefulness for uniformity mapping, e.g. for tool optimization, is limited by excessive measurement time. Thus, we develop and demonstrate a fast complementary static magnetic field method focused only on measurement of RA. We...... compare the static field method to the standard CIPT method and find perfect agreement between the extracted RA values and measurement repeatability while the static field method is several times faster. The static field CIPT method is demonstrated for 200 mm wafer mapping showing radial as well...

  15. Static model for a 3-DOF underactuated finger

    Directory of Open Access Journals (Sweden)

    F. Guay

    2011-02-01

    Full Text Available This paper introduces a static model of a three-degree-of-freedom underactuated finger. The model includes all static forces, namely actuation forces, return forces and gravity. All geometric and static parameters can be freely changed (pulley radius, member's mass, etc.. Hence, the model allows complete static simulations to be performed and it can also be used for numerical optimization.

    This paper was presented at the IFToMM/ASME International Workshop on Underactuated Grasping (UG2010, 19 August 2010, Montréal, Canada.

  16. Static magnets: what are they and what do they do?

    Directory of Open Access Journals (Sweden)

    L Laakso

    Full Text Available INTRODUCTION: Therapeutic static magnets have gained wide community acceptance for neuromusculoskeletal pain relief in many countries yet, apart from strong anecdotal reports of benefit, there is a paucity of scientific evidence for their use. OBJECTIVES: In this review we describe the physical characteristics of traditional and commonplace unipolar and bipolar static magnets as well as newer quadripolar magnetic arrays; discuss what is known of the physiological effects of static magnets and the strength of the literature; and make suggestions for targeted future research for static magnets in the management of neuromusculoskeletal pain conditions.

  17. Diagnostic value of combined static-excretory MR Urography in children with hydroneph

    Directory of Open Access Journals (Sweden)

    Sally Emad-Eldin

    2015-03-01

    Full Text Available The aim of this study was to determine the feasibility, accuracy and diagnostic potential of combined static-excretory MR Urography in children with sonographically detected hydronephrosis. We prospectively evaluated 28 children (11 girls and 17 boys, mean age 8.3 years (range 2 months–16 years. Static-excretory MR Urography was performed in all cases. The results of MR Urography were compared with the results of other imaging modalities, cystoscopy and surgery. In 28 children, 61 renal units were evaluated by MR Urography (the renal unit is the kidney and its draining ureter. The final diagnoses included: normal renal units (n = 23; uretropelvic junction obstruction (n = 14; megaureter (n = 8; midureteric stricture (n = 1, complicated duplicated systems (n = 5, post ESWL non-obstructive dilation (n = 2, extrarenal pelvis (n = 4, dysplastic kidney (n = 4. Complex pathology and more than one disease entity in were found in 7 children. The MRI diagnosis correlated with the final diagnosis in 57 units, with diagnostic accuracy 93.4%. In conclusions static and excretory MRU give both morphological and functional information in a single examination without exposure to ionizing radiation and iodinated contrast agent. It is a valuable imaging technique for children with upper urinary tract dilatation; especially in cases of complex congenital pathologies and severely hydronephrotic kidney.

  18. Photodetachment of H- by a short laser pulse in crossed static electric and magnetic fields

    International Nuclear Information System (INIS)

    Peng Liangyou; Wang Qiaoling; Starace, Anthony F.

    2006-01-01

    We present a detailed quantum mechanical treatment of the photodetachment of H - by a short laser pulse in the presence of crossed static electric and magnetic fields. An exact analytic formula is presented for the final state electron wave function (describing an electron in both static electric and magnetic fields and a short laser pulse of arbitrary intensity). In the limit of a weak laser pulse, final state electron wave packet motion is examined and related to the closed classical electron orbits in crossed static fields predicted by Peters and Delos [Phys. Rev. A 47, 3020 (1993)]. Owing to these closed orbit trajectories, we show that the detachment probability can be modulated, depending on the time delay between two laser pulses and their relative phase, thereby providing a means to partially control the photodetachment process. In the limit of a long, weak pulse (i.e., a monochromatic radiation field) our results reduce to those of others; however, for this case we analyze the photodetachment cross section numerically over a much larger range of electron kinetic energy (i.e., up to 500 cm -1 ) than in previous studies and relate the detailed structures both analytically and numerically to the above-mentioned, closed classical periodic orbits

  19. Diagnostic value of combined static-excretory MR Urography in children with hydronephrosis

    Science.gov (United States)

    Emad-Eldin, Sally; Abdelaziz, Omar; El-Diasty, Tarek A.

    2014-01-01

    The aim of this study was to determine the feasibility, accuracy and diagnostic potential of combined static-excretory MR Urography in children with sonographically detected hydronephrosis. We prospectively evaluated 28 children (11 girls and 17 boys), mean age 8.3 years (range 2 months–16 years). Static-excretory MR Urography was performed in all cases. The results of MR Urography were compared with the results of other imaging modalities, cystoscopy and surgery. In 28 children, 61 renal units were evaluated by MR Urography (the renal unit is the kidney and its draining ureter). The final diagnoses included: normal renal units (n = 23); uretropelvic junction obstruction (n = 14); megaureter (n = 8); midureteric stricture (n = 1), complicated duplicated systems (n = 5), post ESWL non-obstructive dilation (n = 2), extrarenal pelvis (n = 4), dysplastic kidney (n = 4). Complex pathology and more than one disease entity in were found in 7 children. The MRI diagnosis correlated with the final diagnosis in 57 units, with diagnostic accuracy 93.4%. In conclusions static and excretory MRU give both morphological and functional information in a single examination without exposure to ionizing radiation and iodinated contrast agent. It is a valuable imaging technique for children with upper urinary tract dilatation; especially in cases of complex congenital pathologies and severely hydronephrotic kidney. PMID:25750748

  20. A first step towards a consensus static in vitro model for simulating full-term infant digestion.

    Science.gov (United States)

    Ménard, O; Bourlieu, C; De Oliveira, S C; Dellarosa, N; Laghi, L; Carrière, F; Capozzi, F; Dupont, D; Deglaire, A

    2018-02-01

    In vitro alternatives to clinical trials are used for studying human food digestion. For simulating infant digestion, only a few models, lacking physiological relevance, are available. Thanks to an extensive literature review of the in vivo infant digestive conditions, a gastrointestinal static in vitro model was developed for infants born at term and aged 28days. The model was applied to the digestion of a commercial infant formula. Kinetics of digestion, as well as the structural evolution, were compared with those obtained while submitting the same formula to the adult international consensus protocol of in vitro static digestion. The kinetics of proteolysis and lipolysis differed according to the physiological stage resulting mainly from the reduced level of enzymes and bile salts, as well as the higher gastric pH in the infant model. This in vitro static model of infant digestion is of interest for scientists, food or pharmaceutical manufacturers. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Static corrections for enhanced signal detection at IMS seismic arrays

    Science.gov (United States)

    Wilkins, Neil; Wookey, James; Selby, Neil

    2016-04-01

    Seismic monitoring forms an important part of the International Monitoring System (IMS) for verifying the Comprehensive nuclear Test Ban Treaty (CTBT). Analysis of seismic data can be used to discriminate between nuclear explosions and the tens of thousands of natural earthquakes of similar magnitude that occur every year. This is known as "forensic seismology", and techniques include measuring the P-to-S wave amplitude ratio, the body-to-surface wave magnitude ratio (mb/Ms), and source depth. Measurement of these seismic discriminants requires very high signal-to-noise ratio (SNR) data, and this has led to the development and deployment of seismic arrays as part of the IMS. Array processing methodologies such as stacking can be used, but optimum SNR improvement needs an accurate estimate of the arrival time of the particular seismic phase. To enhance the imaging capability of IMS arrays, we aim to develop site-specific static corrections to the arrival time as a function of frequency, slowness and backazimuth. Here, we present initial results for the IMS TORD array in Niger. Vespagrams are calculated for various events using the F-statistic to clearly identify seismic phases and measure their arrival times. Observed arrival times are compared with those predicted by 1D and 3D velocity models, and residuals are calculated for a range of backazimuths and slownesses. Finally, we demonstrate the improvement in signal fidelity provided by these corrections.

  2. Global structure of static spherically symmetric solutions surrounded by quintessence

    Science.gov (United States)

    Cruz, Miguel; Ganguly, Apratim; Gannouji, Radouane; Leon, Genly; Saridakis, Emmanuel N.

    2017-06-01

    We investigate all static spherically symmetric solutions in the context of general relativity surrounded by a minimally-coupled quintessence field, using dynamical system analysis. Applying the 1  +  1  +  2 formalism and introducing suitable normalized variables involving the Gaussian curvature, we were able to reformulate the field equations as first order differential equations. In the case of a massless canonical scalar field we recovered all known black hole results, such as the Fisher solution, and we found that apart from the Schwarzschild solution all other solutions are naked singularities. Additionally, we identified the symmetric phase space which corresponds to the white hole part of the solution and in the case of a phantom field, we were able to extract the conditions for the existence of wormholes and define all possible classes of solutions such as cold black holes, singular spacetimes and wormholes such as the Ellis wormhole, for example. For an exponential potential, we found that the black hole solution which is asymptotically flat is unique and it is the Schwarzschild spacetime, while all other solutions are naked singularities. Furthermore, we found solutions connecting to a white hole through a maximum radius, and not a minimum radius (throat) such as wormhole solutions, therefore violating the flare-out condition. Finally, we have found a necessary and sufficient condition on the form of the potential to have an asymptotically AdS spacetime along with a necessary condition for the existence of asymptotically flat black holes.

  3. Coupling of Nod1D and HOTCHANNEL: static case

    International Nuclear Information System (INIS)

    Gomez T, A.M.; Ovando C, R.

    2003-01-01

    In this work the joining of the programs Nod1D and HOTCHANNEL, developed in the National Polytechnic Institute (IPN) and in the Electrical Research Institute (IIE) respectively is described. The first one allows to study the neutronic of a nuclear reactor and the second one allows to carry out the analysis of hot channel of a Boiling Water Reactor (BWR). Nod1 D is a program that it solves by nodal methods type finite element those diffusion equations in multigroup, and it is the static part of Nod Kin that it solves the diffusion equation in their time dependent part. For another side HOTCHANNEL is based on a mathematical model constituted by four conservation equations (two of mass conservation, one of motion quantity and one of energy), which are solved applying one discretization in implicit finite differences. Both programs have been verified in independent form using diverse test problems. In this work the modifications that were necessary to carry out to both for obtaining a coupled program that it provides the axial distribution of the neutron flux, the power, the burnup and the void fraction, among others parameters as much as neutronic as thermal hydraulics are described. Those are also mentioned limitations, advantages and disadvantages of the final product to which has been designated Nod1 D-HotChn. Diverse results for the Cycle 1 of the Laguna Verde Unit 1 reactor of the Nucleo electric central comparing them with those obtained directly with the CoreMasterPresto code are provided. (Author)

  4. Static and dynamic properties of smoothed dissipative particle dynamics

    Science.gov (United States)

    Alizadehrad, Davod; Fedosov, Dmitry A.

    2018-03-01

    In this paper, static and dynamic properties of the smoothed dissipative particle dynamics (SDPD) method are investigated. We study the effect of method parameters on SDPD fluid properties, such as structure, speed of sound, and transport coefficients, and show that a proper choice of parameters leads to a well-behaved and accurate fluid model. In particular, the speed of sound, the radial distribution function (RDF), shear-thinning of viscosity, the mean-squared displacement (〈R2 〉 ∝ t), and the Schmidt number (Sc ∼ O (103) - O (104)) can be controlled, such that the model exhibits a fluid-like behavior for a wide range of temperatures in simulations. Furthermore, in addition to the consideration of fluid density variations for fluid compressibility, a more challenging test of incompressibility is performed by considering the Poisson ratio and divergence of velocity field in an elongational flow. Finally, as an example of complex-fluid flow, we present the applicability and validity of the SDPD method with an appropriate choice of parameters for the simulation of cellular blood flow in irregular geometries. In conclusion, the results demonstrate that the SDPD method is able to approximate well a nearly incompressible fluid behavior, which includes hydrodynamic interactions and consistent thermal fluctuations, thereby providing, a powerful approach for simulations of complex mesoscopic systems.

  5. Statics and dynamics of colloidal particles on optical tray arrays

    Energy Technology Data Exchange (ETDEWEB)

    Reichardt, Charles [Los Alamos National Laboratory; Reichhardt, Cynthia J [Los Alamos National Laboratory

    2009-01-01

    We examine the statics and dynamics of charged colloids interacting with periodic optical trap arrays. In particular we study the regime where more than one colloid is confined in each trap, creating effective dimer, trimer, and higher order states called colloidal molecular crystals. The n-mer states have all effective orientational degree of freedom which can be controlled with an external driving field. In general, the external field causes a polarization effect where the orientation of the n-mers aligns with the external field, similar to liquid crystal systems. Additionally, under a rotating external drive the n-mers can rotate with the drive. In some cases a series of structural transitions in the colloidal crystal states occur in the rotating field due to a competition between the ordering of the colloidal molecular crystals and the polarization effect which orients the n-mers in the direction of the drive. We also show that for some parameters, the n-mers continuously rotate with the drive without witching, that depinning transitions can occur where the colloids jump from well to well, and that there are a number of distinct dynamical transitions between the phases. Finally, we illustrate colloidal orderings at fillings of more than four colloids per trap, indicating that it is possible to create higher order colloidal crystal cluster phases.

  6. Error analysis of large aperture static interference imaging spectrometer

    Science.gov (United States)

    Li, Fan; Zhang, Guo

    2015-12-01

    Large Aperture Static Interference Imaging Spectrometer is a new type of spectrometer with light structure, high spectral linearity, high luminous flux and wide spectral range, etc ,which overcomes the contradiction between high flux and high stability so that enables important values in science studies and applications. However, there're different error laws in imaging process of LASIS due to its different imaging style from traditional imaging spectrometers, correspondingly, its data processing is complicated. In order to improve accuracy of spectrum detection and serve for quantitative analysis and monitoring of topographical surface feature, the error law of LASIS imaging is supposed to be learned. In this paper, the LASIS errors are classified as interferogram error, radiometric correction error and spectral inversion error, and each type of error is analyzed and studied. Finally, a case study of Yaogan-14 is proposed, in which the interferogram error of LASIS by time and space combined modulation is mainly experimented and analyzed, as well as the errors from process of radiometric correction and spectral inversion.

  7. Static characteristic analysis and experimental research of aerostatic thrust bearing with annular elastic uniform pressure plate

    Directory of Open Access Journals (Sweden)

    Hao Dong

    2015-03-01

    Full Text Available In this article, an aerostatic thrust bearing with annular elastic uniform pressure plate structure was designed. In order to obtain a relationship between bearing capacity and stiffness of aerostatic thrust bearing designed in this article, first, the stress field mechanics model of the gas thrust bearing was established in the static. Second, deformation control equations of the elastic uniform pressure plate and gas lubrication Reynolds equation were established according to the flow continuity principle. Here, finite element mesh of gas flow field was woven using the technology of grid overlapping and grid stitching. Then, gas–solid coupling control equations were solved using the numerical method. Gas film pressure distribution and gas static bearing capacity of thrust bearing were analyzed. Function relationship between bearing capacity and the stiffness and the thickness of gas film was obtained. Finally, the results of theory analysis and experiment were compared. The results of the comparison can be listed as, under the effect of gas pressure, orifice area and the equilibrium pressure groove depth are changed due to elastic deformation of the elastic uniform pressure plate. The static stiffness of aerostatic thrust bearing with elastic equilibrium pressure groove increased by 30% than the static stiffness of aerostatic thrust bearing with rigid equilibrium pressure groove. The maximum carrying capacity occurred in the gas film thickness of 3.5 µm. The maximum static stiffness appeared in the gas film thickness of 5.5 µm. It can be seen from the comparison results of experiments and theoretical analysis that data results of gas film thickness and the bearing capacity are the same. The feasibility of the theoretical analysis method is validated.

  8. Utsu aftershock productivity law explained from geometric operations on the permanent static stress field of mainshocks

    Science.gov (United States)

    Mignan, Arnaud

    2018-03-01

    The aftershock productivity law is an exponential function of the form K ∝ exp(αM), with K being the number of aftershocks triggered by a given mainshock of magnitude M and α ≈ ln(10) being the productivity parameter. This law remains empirical in nature although it has also been retrieved in static stress simulations. Here, we parameterize this law using the solid seismicity postulate (SSP), the basis of a geometrical theory of seismicity where seismicity patterns are described by mathematical expressions obtained from geometric operations on a permanent static stress field. We first test the SSP that relates seismicity density to a static stress step function. We show that it yields a power exponent q = 1.96 ± 0.01 for the power-law spatial linear density distribution of aftershocks, once uniform noise is added to the static stress field, in agreement with observations. We then recover the exponential function of the productivity law with a break in scaling obtained between small and large M, with α = 1.5ln(10) and ln(10), respectively, in agreement with results from previous static stress simulations. Possible biases of aftershock selection, proven to exist in epidemic-type aftershock sequence (ETAS) simulations, may explain the lack of break in scaling observed in seismicity catalogues. The existence of the theoretical kink, however, remains to be proven. Finally, we describe how to estimate the solid seismicity parameters (activation density δ+, aftershock solid envelope r∗ and background stress amplitude range Δo∗) for large M values.

  9. Pantex staging study near-term alternatives

    Energy Technology Data Exchange (ETDEWEB)

    Madden, M.S.; Adickes, M.D.; Hostick, C.J.; Nealey, S.M.; Smith, B.W.

    1992-12-01

    As the result of bilateral treaties to reduce the number of weapons in the nuclear stockpile, the US Department of Energy must now address the requirements for additional storage of the plutonium components (pits) from the retired weapons at Pantex until the components' final disposition. Because of the critical need to take action, Pantex has initiated two related efforts: Project Stage Right and this Staging Study. While support of Project Stage Right is a key objective of this study, the scope covers a broader range of activities and aspects of the pit staging problem. This study provides estimates of worker radiation exposures under the current scenario as well as estimated radiation exposure for workers under four alternative staging scenarios. An important objective of this study also identifies and recommends for future study other activities related to staging where radiation safety and overall efficiency can be improved.

  10. Pantex staging study near-term alternatives

    Energy Technology Data Exchange (ETDEWEB)

    Madden, M.S.; Adickes, M.D.; Hostick, C.J.; Nealey, S.M.; Smith, B.W.

    1992-12-01

    As the result of bilateral treaties to reduce the number of weapons in the nuclear stockpile, the US Department of Energy must now address the requirements for additional storage of the plutonium components (pits) from the retired weapons at Pantex until the components` final disposition. Because of the critical need to take action, Pantex has initiated two related efforts: Project Stage Right and this Staging Study. While support of Project Stage Right is a key objective of this study, the scope covers a broader range of activities and aspects of the pit staging problem. This study provides estimates of worker radiation exposures under the current scenario as well as estimated radiation exposure for workers under four alternative staging scenarios. An important objective of this study also identifies and recommends for future study other activities related to staging where radiation safety and overall efficiency can be improved.

  11. Latent Constructs of the Static-99R and Static-2002R: A Three-Factor Solution.

    Science.gov (United States)

    Brouillette-Alarie, Sébastien; Babchishin, Kelly M; Hanson, R Karl; Helmus, Leslie-Maaike

    2016-02-01

    The most commonly used risk assessment tools for predicting sexual violence focus almost exclusively on static, historical factors (e.g., characteristics of prior offences). Consequently, they are assumed to be unable to directly inform the selection of treatment targets or evaluate change. In this article, we argue that this limitation can be mitigated by using latent variable models as a framework to link historical risk factors to the psychological characteristics of offenders. Accordingly, we conducted a factor analysis of the 13 nonredundant items from the two most commonly used risk tools for sexual offenders (Static-99R and Static-2002R) to identify the psychological information contained in these tools. Three factors were identified: (a) persistence/paraphilia, a construct related to sexual criminality, especially of the pedophilic type; (b) youthful stranger aggression, a construct centered on young age and offence seriousness; and (c) general criminality, a construct that reflected the diversity and magnitude of criminal careers. These constructs predicted sexual recidivism with similar accuracy, but only youthful stranger aggression and general criminality predicted nonsexual recidivism. These results indicate that risk tools for sexual violence are multidimensional, and support a shift from a focus on atheoretical risk markers to the assessment of psychologically meaningful constructs. © The Author(s) 2015.

  12. Quasi-static modelling of compliant mechanisms: application to a 2-DOF underactuated finger

    Directory of Open Access Journals (Sweden)

    C. Quennouelle

    2011-02-01

    Full Text Available In this paper, the kinematostatic and the quasi-static models of parallel mechanisms are applied to underactuated mechanisms. Both models are extended to the cases for which the actuated joints are not kinematically independent, and for which the external loads are function of the configuration of the mechanism, the grasped object being considered as not perfectly rigid. An application to a 2-DOF underactuated compliant finger is then presented with details about the implementation of the kinematostatic and the quasi-static models. Finally, some numerical results are given that illustrate possible contributions of these models for the analysis and the control of underactuated mechanisms.

    This paper was presented at the IFToMM/ASME International Workshop on Underactuated Grasping (UG2010, 19 August 2010, Montréal, Canada.

  13. Pattern imprinting in deep sub-micron static random access memories induced by total dose irradiation

    International Nuclear Information System (INIS)

    Zheng Qi-Wen; Yu Xue-Feng; Cui Jiang-Wei; Guo Qi; Ren Di-Yuan; Cong Zhong-Chao; Zhou Hang

    2014-01-01

    Pattern imprinting in deep sub-micron static random access memories (SRAMs) during total dose irradiation is investigated in detail. As the dose accumulates, the data pattern of memory cells loading during irradiation is gradually imprinted on their background data pattern. We build a relationship between the memory cell's static noise margin (SNM) and the background data, and study the influence of irradiation on the probability density function of ΔSNM, which is the difference between two data sides' SNMs, to discuss the reason for pattern imprinting. Finally, we demonstrate that, for micron and deep sub-micron devices, the mechanism of pattern imprinting is the bias-dependent threshold shift of the transistor, but for a deep sub-micron device the shift results from charge trapping in the shallow trench isolation (STI) oxide rather than from the gate oxide of the micron-device. (condensed matter: structural, mechanical, and thermal properties)

  14. Robust Admissibilization of Descriptor Systems by Static Output-Feedback: An LMI Approach

    Directory of Open Access Journals (Sweden)

    M. Chaabane

    2011-01-01

    static output-feedback is studied in this paper and an approach to solve it is proposed. For this, sufficient conditions are derived for the closed-loop system to be admissible (i.e., stable, regular, and impulse-free. These conditions are expressed in terms of a strict Linear Matrix Inequality (LMI; so they are tractable using numerical computations. The proposed controller design methodology is based on two steps: the first is dedicated to synthesizing a classical state-feedback controller, which is used as the initial value for the second step, which uses an LMI problem to obtain static output-feedback controllers that give admissibility. Finally, a numerical example is given to illustrate the results.

  15. Pattern imprinting in deep sub-micron static random access memories induced by total dose irradiation

    Science.gov (United States)

    Zheng, Qi-Wen; Yu, Xue-Feng; Cui, Jiang-Wei; Guo, Qi; Ren, Di-Yuan; Cong, Zhong-Chao; Zhou, Hang

    2014-10-01

    Pattern imprinting in deep sub-micron static random access memories (SRAMs) during total dose irradiation is investigated in detail. As the dose accumulates, the data pattern of memory cells loading during irradiation is gradually imprinted on their background data pattern. We build a relationship between the memory cell's static noise margin (SNM) and the background data, and study the influence of irradiation on the probability density function of ΔSNM, which is the difference between two data sides' SNMs, to discuss the reason for pattern imprinting. Finally, we demonstrate that, for micron and deep sub-micron devices, the mechanism of pattern imprinting is the bias-dependent threshold shift of the transistor, but for a deep sub-micron device the shift results from charge trapping in the shallow trench isolation (STI) oxide rather than from the gate oxide of the micron-device.

  16. A study of viscoelasticity index for evaluating muscle hypotonicity during static stretching.

    Science.gov (United States)

    Okamura, Naomi; Tsukune, Mariko; Kobayashi, Yo; Fujie, Masakatsu G

    2014-01-01

    Static stretching is widely used as a preventative treatment for musculoskeletal disabilities by providing muscle hypotonicity, which results from changes in muscle tissue structure. However, the quantitative evaluation of hypotonicity during stretching has had limited success owing to the confounding factor of mechanical stress relaxation. To resolve this problem, we propose a new evaluation method for hypotonicity based on a viscoelastic muscle model using fractional calculus, which is known to be effective for biomaterials. We made continuous measurements of rectus skin indentation during static stretching as an indicator of reaction force in the rectus femoris muscle. The viscoelastic ratio and modulus were computed from the indentation trace. Both viscoelastic parameters decreased significantly between the early and final phases of stretching. The results suggest that our method is useful for quantitative evaluation of muscle hypotonicity during stretching.

  17. Learning about static electricity and magnetism in a fourth-grade classroom

    Science.gov (United States)

    Henry, David Roy

    Students begin to develop mental models to explain electrostatic and magnetic phenomena throughout childhood, middle childhood and high school, although these mental models are often incoherent and unscientific (Borges, Tenico, & Gilbert, 1998; Maloney, 1985). This is a case study of a classroom of grade four students and the mental models of magnetism and static electricity they used during a six-week science unit. The 22 students studied magnetism and static electricity using inquiry activities structured to create an environment where students would be likely to construct powerful scientific ideas (Goldberg & Bendall, 1995). Multiple data sources, including students' writing, student assessments, teacher interviews, student interviews, teacher journals, and classroom video and audio recordings were used to uncover how fourth grade students made sense of static electricity and magnetism before, during, and after instruction. The data were analyzed using a social constructivist framework to determine if students were able to develop target scientific ideas about static electricity and magnetism. In general, students were found to have three core mental models prior to instruction: (1) Static electricity and magnetism are the same "substance"; (2) This substance exists on the surface of a magnet or a charged object and can be rubbed off, and (3) Opposite substances attract. During the activities, students had many opportunities to observe evidence that contradicted these core mental models. Using evidence from direct observations, the students practiced differentiating between evidence and ideas. Through group and class discussions, they developed evidenced-based (scientific) ideas. Final assessments revealed that students were able to construct target ideas such as: (1) static electricity and magnetism are fundamentally different; (2) there are two kinds of static "charge;" (3) magnet-rubbed wires act like a magnet; and (4) opposite substances move toward each

  18. Breast cancer staging

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/patientinstructions/000911.htm Breast cancer staging To use the sharing features on this ... Once your health care team knows you have breast cancer , they will do more tests to stage it. ...

  19. Seven Stages of Alzheimer's

    Science.gov (United States)

    ... Dementias . Learn more: Daily Care and Behaviors Severe Alzheimer's disease (late-stage) Get support Late-stage care decisions can be some of the hardest families face. Connect with other caregivers who have been through the process on our ...

  20. Stages of Adolescence

    Science.gov (United States)

    ... Español Text Size Email Print Share Stages of Adolescence Page Content Article Body Adolescence, these years from puberty to adulthood, may be roughly divided into three stages: early adolescence, generally ages eleven to fourteen; middle adolescence, ages ...

  1. Static Test Compaction As A Minimum Covering Problem | Boateng ...

    African Journals Online (AJOL)

    Large numbers of test stimuli impact on the time and cost of test application. Hence there is the need to keep numbers of test stimuli low while maintaining as high fault coverage as possible. In this paper, static compaction of test stimuli is seen as a minimization problem. The task of static compaction of a set of test stimuli ...

  2. 14 CFR 25.681 - Limit load static tests.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Limit load static tests. 25.681 Section 25.681 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT... load static tests. (a) Compliance with the limit load requirements of this Part must be shown by tests...

  3. Navigating on handheld displays: Dynamic versus Static Keyhole Navigation

    NARCIS (Netherlands)

    Mehra, S.; Werkhoven, P.; Worring, M.

    2006-01-01

    Handheld displays leave little space for the visualization and navigation of spatial layouts representing rich information spaces. The most common navigation method for handheld displays is static peephole navigation: The peephole is static and we move the spatial layout behind it (scrolling). A

  4. Formula for Forced Vibration Analysis of Structures Using Static ...

    African Journals Online (AJOL)

    This Paper proposed and examined a formula for forced vibration analysis of structures using static factored response as equivalent dynamic response. Some methods of dynamic analysis are based on using static factored response as equivalent dynamic response thereby excluding the formulation of the equations of ...

  5. 14 CFR 23.681 - Limit load static tests.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Limit load static tests. 23.681 Section 23.681 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT... Control Systems § 23.681 Limit load static tests. (a) Compliance with the limit load requirements of this...

  6. 14 CFR 27.681 - Limit load static tests.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Limit load static tests. 27.681 Section 27.681 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT... static tests. (a) Compliance with the limit load requirements of this part must be shown by tests in...

  7. 14 CFR 29.681 - Limit load static tests.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Limit load static tests. 29.681 Section 29.681 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT... load static tests. (a) Compliance with the limit load requirements of this part must be shown by tests...

  8. Internal dynamics around static-deformation FEM states

    NARCIS (Netherlands)

    Ligterink, N.E.

    2005-01-01

    Constant velocity or constant force FEM solutions are static-deformation states, where the elastic deformation is stationary. These are the typical operation conditions. Time-dependence, or fluctuations, of the static-deformation states are treated as perturbations, leading to a fast-converging

  9. 40 CFR 53.64 - Test procedure: Static fractionator test.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 5 2010-07-01 2010-07-01 false Test procedure: Static fractionator test. 53.64 Section 53.64 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Performance Characteristics of Class II Equivalent Methods for PM2.5 § 53.64 Test procedure: Static...

  10. Static and Transient Cavitation Threshold Measurements for Mercury

    Energy Technology Data Exchange (ETDEWEB)

    Moraga, F.; Taleyarkhan, R.P.

    1999-11-14

    Transient and static cavitation thresholds for mercury as a function of the cover gas (helium or air), and pressure are reported. Both static and transient cavitation onset pressure thresholds increase linearly with cover gas pressure. Additionally, the cavitation thresholds as a function of dissolved gases were also measured and are reported.

  11. Multiple histogram method and static Monte Carlo sampling

    NARCIS (Netherlands)

    Inda, M.A.; Frenkel, D.

    2004-01-01

    We describe an approach to use multiple-histogram methods in combination with static, biased Monte Carlo simulations. To illustrate this, we computed the force-extension curve of an athermal polymer from multiple histograms constructed in a series of static Rosenbluth Monte Carlo simulations. From

  12. STATIC TEST COMPACTION AS A MINIMUM COVERING PROBLEM

    African Journals Online (AJOL)

    DEPT OF AGRICULTURAL ENGINEERING

    ABSTRACT. Large numbers of test stimuli impact on the time and cost of test application. Hence there is the need to keep numbers of test stimuli low while maintaining as high fault coverage as possible. In this paper, static compaction of test stimuli is seen as a minimization problem. The task of static compaction of a set of ...

  13. The Renormalization Group Improvement of the QCD Static Potentials

    CERN Document Server

    Pineda-Ruiz, A; Pineda, Antonio; Soto, Joan

    2000-01-01

    We resum the leading ultrasoft logs of the singlet and octet static QCD potentials within potential NRQCD. We then obtain the complete three-loop renormalization group improvement of the singlet QCD static potential. The discrepancies between the perturbative evaluation and the lattice results at short distances are slightly reduced.

  14. Hanging an Airplane: A Case Study in Static Equilibrium

    Science.gov (United States)

    Katz, Debora M.

    2009-01-01

    Our classrooms are filled with engineering majors who take a semester-long course in static equilibrium. Many students find this class too challenging and drop their engineering major. In our introductory physics class, we often breeze through static equilibrium; to physicists equilibrium is just a special case of Newton's second law. While it is…

  15. CONTINUOUS PRODUCTION OF HYDROXYPROPYL STARCH IN A STATIC MIXER REACTOR

    NARCIS (Netherlands)

    LAMMERS, G; STAMHUIS, EJ; BEENACKERS, AACM

    A novel type of reactor for the chemical derivatization of starch pastes is presented. The design is based on the application of static mixers. The reactor shows excellent plug flow behaviour with a Peclet number of about 100. The viscosity behaviour of concentrated starch pastes in the static mixer

  16. Static energy meter errors caused by conducted electromagnetic interference

    NARCIS (Netherlands)

    Leferink, Frank Bernardus Johannes; Keyer, Cornelis H.A.; Melentjev, Anton

    2017-01-01

    Static, or electronic, energy meters are replacing the conventional electromechanical meters. Consumers are some-times complaining about higher energy readings and billing after the change to a static meter, but there is not a clear common or root cause at present. Electromagnetic interference has

  17. No-go theorem for static boson stars

    Directory of Open Access Journals (Sweden)

    Shahar Hod

    2018-03-01

    Full Text Available It is proved that self-gravitating static scalar fields whose self-interaction potential V(ψ2 is a monotonically increasing function of its argument cannot form spherically symmetric asymptotically flat bound matter configurations. Our compact theorem rules out, in particular, the existence of spatially regular static boson stars made of nonlinear massive scalar fields.

  18. Non-static vacuum strings: exterior and interior solutions

    International Nuclear Information System (INIS)

    Stein-Schabes, J.A.

    1986-01-01

    New non-static cylindrically symmetric solutions of Einsteins's equations are presented. Some of these solutions represent string-like objects. An exterior vacuum solution is matched to a non-vacuum interior solution for different forms of the energy-momentum tensor. They generalize the standard static string. 12 refs

  19. All Charged Up!--Experimenting with Static Electricity

    Science.gov (United States)

    Roman, Harry T.

    2011-01-01

    Build-up of static electricity happens readily when the air is cold and dry and is a common part of life. There are lots of ways to make students aware of static electricity--and many things one can teach them about its applications in today's industry. In this article, the author describes examples and experiments that will bring static…

  20. 14 CFR 29.610 - Lightning and static electricity protection.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Lightning and static electricity protection... § 29.610 Lightning and static electricity protection. (a) The rotorcraft structure must be protected... electricity must— (1) Minimize the accumulation of electrostatic charge; (2) Minimize the risk of electric...

  1. 14 CFR 25.173 - Static longitudinal stability.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Static longitudinal stability. 25.173... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Flight Stability § 25.173 Static... forces (including friction) must be as follows: (a) A pull must be required to obtain and maintain speeds...

  2. Static friction of stainless steel wire rope–rubber contacts.

    NARCIS (Netherlands)

    Loeve, A.J.; Krijger, T.; Mugge, W.; Breedveld, P.; Dodou, D.; Dankelman, J.

    2014-01-01

    Little is known about static friction of stainless-steel wire ropes ('cables') in contact with soft rubbers, an interface of potential importance for rigidifiable medical instruments. Although friction theories imply that the size and profile of the cables affect static friction, there are no

  3. Slipping and Tipping: Measuring Static Friction with a Straightedge

    Science.gov (United States)

    Dietz, Eric; Aguilar, Isaac

    2012-01-01

    Following a discussion of forces, torques, and the conditions for static equilibrium, I tell my introductory mechanics class that I will show them how to measure the coefficient of static friction, us, between the surfaces of a block and the front bench using "nothing but a straightedge". After a few seconds of hushed anticipation, I nudge the…

  4. 14 CFR 23.173 - Static longitudinal stability.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Static longitudinal stability. 23.173... Stability § 23.173 Static longitudinal stability. Under the conditions specified in § 23.175 and with the airplane trimmed as indicated, the characteristics of the elevator control forces and the friction within...

  5. No-go theorem for static boson stars

    Science.gov (United States)

    Hod, Shahar

    2018-03-01

    It is proved that self-gravitating static scalar fields whose self-interaction potential V (ψ2) is a monotonically increasing function of its argument cannot form spherically symmetric asymptotically flat bound matter configurations. Our compact theorem rules out, in particular, the existence of spatially regular static boson stars made of nonlinear massive scalar fields.

  6. Feshbach resonances in cesium at ultralow static magnetic fields

    NARCIS (Netherlands)

    Papoular, D.J.; Bize, S.; Clairon, A.; Marion, H.; Kokkelmans, S.J.J.M.F.; Shlyapnikov, G.V.

    2012-01-01

    We have observed Feshbach resonances for 133Cs atoms in two different hyperfine states at static magnetic fields of a few milligauss. These resonances are unusual for two main reasons. First, they are the lowest static-field resonances investigated up to now, and we explain their multipeak structure

  7. Modeling a nucleon system: static and dynamical properties - density fluctuations

    International Nuclear Information System (INIS)

    Idier, D.

    1997-01-01

    This thesis sets forth a quasi-particle model for the static and dynamical properties of nuclear matter. This model is based on a scale ratio of quasi-particle to nucleons and the projection of the semi-classical distribution on a coherent Gaussian state basis. The first chapter is dealing with the transport equations, particularly with the Vlasov equation for Wigner distribution function. The second one is devoted to the statics of nuclear matter. Here, the sampling effect upon the nuclear density is treated and the state equation of the Gaussian fluid is compared with that given by Hartree-Fock approximation. We define state equation as the relationship between the nucleon binding energy and density, for a given temperature. The curvature around the state equation minimum of the quasi-particle system is shown to be related to the speed of propagation of density perturbation. The volume energy and the surface properties of a (semi-)infinite nucleon system are derived. For the resultant saturated auto-coherent semi-infinite system of quasi-particles the surface coefficient appearing in the mass formula is extracted as well as the system density profile. The third chapter treats the dynamics of the two-particle residual interactions. The effect of different parameters on relaxation of a nucleon system without a mean field is studied by means of a Eulerian and Lagrangian modeling. The fourth chapter treats the volume instabilities (spinodal decomposition) in nuclear matter. The quasi-particle systems, initially prepared in the spinodal region of the utilized interaction, are set to evolve. It is shown then that the scale ratio acts upon the amount of fluctuations injected in the system. The inhomogeneity degree and a proper time are defined and the role of collisions in the spinodal decomposition as well as that of the initial temperature and density, are investigated. Assuming different effective macroscopic interactions, the influence of quantities as

  8. Static inverter with synchronous output waveform synthesized by time-optimal-response feedback

    Science.gov (United States)

    Kernick, A.; Stechschulte, D. L.; Shireman, D. W.

    1976-01-01

    Time-optimal-response 'bang-bang' or 'bang-hang' technique, using four feedback control loops, synthesizes static-inverter sinusoidal output waveform by self-oscillatory but yet synchronous pulse-frequency-modulation (SPFM). A single modular power stage per phase of ac output entails the minimum of circuit complexity while providing by feedback synthesis individual phase voltage regulation, phase position control and inherent compensation simultaneously for line and load disturbances. Clipped sinewave performance is described under off-limit load or input voltage conditions. Also, approaches to high power levels, 3-phase arraying and parallel modular connection are given.

  9. Learning to produce predicted static handgrip forces.

    Science.gov (United States)

    Angyán, L; Téczely, T; Karsai, I

    2005-01-01

    The objective of this study was to prove the hypothesis that kinaesthetic sensations, without visual or verbal guidance, give sufficient information to produce predictive handgrip forces. The ability of 70 girls and 70 boys aged 11 to 17 years to produce predicted static handgrip force was examined. The subjects were requested to produce 50% of their individual maximum handgrip force and maintain it for 2 seconds without visual control. Ten trials were done first by the right-hand and then by the left-hand. The maximum grip strength increased parallel with age, but significant differences were found between both the right and the left-hand, and the genders. Close correlations were found between the desired and the exerted forces. The differences between the desired forces and the exerted forces produced by the fifth trials were significantly smaller than that of the first trials. The verbal information about each exerted force contributed to the learning with right-hand since it caused a further decrease in the difference between the desired force and the exerted force. In contrast, the learning with left-hand was not enhanced by verbal feedback. These results suggest that kinaesthetic feedback information from the hand plays an effective role in learning to produce predicted grip strengths without visual and verbal information.

  10. Static recrystallization behavior of AEREX350 superalloy

    Energy Technology Data Exchange (ETDEWEB)

    Hosseinifar, Mehdi, E-mail: hossem@mcmaster.ca [Department of Materials Science and Engineering, Sharif University of Technology, P.O. Box 11365-9466, Tehran (Iran, Islamic Republic of); Asgari, Sirous, E-mail: sasgari@sharif.edu [Department of Materials Science and Engineering, Sharif University of Technology, P.O. Box 11365-9466, Tehran (Iran, Islamic Republic of)

    2010-10-25

    Research highlights: {yields} The static recrystallization behavior of a complex superalloy, AEREX 350, is investigated. {yields} It is found that this alloy resists recrystallization to very high temperatures (1025 deg. C, 0.81T{sub m}). {yields} TEM investigation showed evidence of grain boundary pinning by the Widmanstaetten {eta} platelets. {yields} Recrystallization of the AEREX 350 superalloy proceeds by the discontinuous precipitation of the {eta} particles behind the moving boundary. - Abstract: The recrystallization behavior of a commercial nickel-cobalt base superalloy, AEREX 350, is investigated by means of hardness test, X-ray diffraction, and microscopy. It is found that the alloy resists recrystallization up to a high temperature of 1025 deg. C. Recrystallized grains are readily formed at grain boundaries below this temperature; however, the growth of these new grains is inhibited by Widmanstaetten {eta} particles having coherent facets with the nickel matrix ({gamma}). The passage of the recrystallization front results in coherency loss and consequently dissolution of the {eta} platelets. Recrystallization proceeds with a discontinuous precipitation of the {eta} phase behind the moving boundary.

  11. Universe Interactive: Static Displays with Active Components

    Science.gov (United States)

    Larson, Michelle B.

    2005-01-01

    As the World Year of Physics (WYP) approaches, the AAPT WYP Committee would like to encourage everyone to consider ways to engage those around us in celebrating the science that makes us the proud geeks we are. The geek sentiment is my own, and does not necessarily reflect the views and opinions of the committee. This paper offers simple and inexpensive astronomy-related ideas for a bulletin-board-type display. The particular ideas presented below are hands-on classroom activities that I've adapted for display purposes. The display is static in that once constructed it does not require a personal facilitator, but each component invites interaction. At the end of the paper I revisit the idea of building a sundial1 as a highly visible and artistic way to engage students and communities in physics. The activities presented here are available for use when constructing your own display. In addition, these examples are meant to illustrate how instructional products might be modified for display purposes, and I encourage others to consider their favorite activities for an interactive display.

  12. Statistical mechanics framework for static granular matter

    Science.gov (United States)

    Henkes, Silke; Chakraborty, Bulbul

    2009-06-01

    The physical properties of granular materials have been extensively studied in recent years. So far, however, there exists no theoretical framework which can explain the observations in a unified manner beyond the phenomenological jamming diagram. This work focuses on the case of static granular matter, where we have constructed a statistical ensemble which mirrors equilibrium statistical mechanics. This ensemble, which is based on the conservation properties of the stress tensor, is distinct from the original Edwards ensemble and applies to packings of deformable grains. We combine it with a field theoretical analysis of the packings, where the field is the Airy stress function derived from the force and torque balance conditions. In this framework, Point J characterized by a diverging stiffness of the pressure fluctuations. Separately, we present a phenomenological mean-field theory of the jamming transition, which incorporates the mean contact number as a variable. We link both approaches in the context of the marginal rigidity picture proposed by Wyart and others.

  13. Liquid methanol under a static electric field

    Science.gov (United States)

    Cassone, Giuseppe; Giaquinta, Paolo V.; Saija, Franz; Saitta, A. Marco

    2015-02-01

    We report on an ab initio molecular dynamics study of liquid methanol under the effect of a static electric field. We found that the hydrogen-bond structure of methanol is more robust and persistent for field intensities below the molecular dissociation threshold whose value (≈0.31 V/Å) turns out to be moderately larger than the corresponding estimate obtained for liquid water. A sustained ionic current, with ohmic current-voltage behavior, flows in this material for field intensities above 0.36 V/Å, as is also the case of water, but the resulting ionic conductivity (≈0.40 S cm-1) is at least one order of magnitude lower than that of water, a circumstance that evidences a lower efficiency of proton transfer processes. We surmise that this study may be relevant for the understanding of the properties and functioning of technological materials which exploit ionic conduction, such as direct-methanol fuel cells and Nafion membranes.

  14. Liquid methanol under a static electric field

    Energy Technology Data Exchange (ETDEWEB)

    Cassone, Giuseppe, E-mail: giuseppe.cassone@impmc.upmc.fr [Sorbonne Universités, UPMC Univ Paris 06, UMR 7590, IMPMC, F-75005 Paris (France); CNRS, UMR 7590, IMPMC, F-75005 Paris (France); Università degli Studi di Messina, Dipartimento di Fisica e di Scienze della Terra, Contrada Papardo, 98166 Messina (Italy); CNR-IPCF, Viale Ferdinando Stagno d’Alcontres 37, 98158 Messina (Italy); Giaquinta, Paolo V., E-mail: paolo.giaquinta@unime.it [Università degli Studi di Messina, Dipartimento di Fisica e di Scienze della Terra, Contrada Papardo, 98166 Messina (Italy); Saija, Franz, E-mail: saija@ipcf.cnr.it [CNR-IPCF, Viale Ferdinando Stagno d’Alcontres 37, 98158 Messina (Italy); Saitta, A. Marco, E-mail: marco.saitta@impmc.upmc.fr [Sorbonne Universités, UPMC Univ Paris 06, UMR 7590, IMPMC, F-75005 Paris (France); CNRS, UMR 7590, IMPMC, F-75005 Paris (France)

    2015-02-07

    We report on an ab initio molecular dynamics study of liquid methanol under the effect of a static electric field. We found that the hydrogen-bond structure of methanol is more robust and persistent for field intensities below the molecular dissociation threshold whose value (≈0.31 V/Å) turns out to be moderately larger than the corresponding estimate obtained for liquid water. A sustained ionic current, with ohmic current-voltage behavior, flows in this material for field intensities above 0.36 V/Å, as is also the case of water, but the resulting ionic conductivity (≈0.40 S cm{sup −1}) is at least one order of magnitude lower than that of water, a circumstance that evidences a lower efficiency of proton transfer processes. We surmise that this study may be relevant for the understanding of the properties and functioning of technological materials which exploit ionic conduction, such as direct-methanol fuel cells and Nafion membranes.

  15. Observation of static gestures influences speech production.

    Science.gov (United States)

    Jarick, Michelle; Jones, Jeffery A

    2008-08-01

    Research investigating 'mirror neurons' has demonstrated the presence of an observation-execution matching system in humans. One hypothesized role for this system might be to aid in action understanding by encoding the underlying intentions of the actor. To investigate this hypothesis, we asked participants to observe photographs of an actor making orofacial gestures (implying verbal or non-verbal acts), and to produce syllables that were compatible or incompatible with the gesture they observed. We predicted that if mirror neurons encode the intentions of an actor, then the pictures implying verbal gestures would affect speech production, whereas the non-verbal gestures would not. Our results showed that the observation of compatible verbal gestures facilitated verbal responses, while incompatible verbal gestures caused interference. Although this compatibility effect did not reach statistical significance when the photographs implied a non-verbal act, responses were faster on average when the gesture implied the use of similar articulators as those involved with the production of the target syllable. Altogether, these behavioral findings compliment previous neuroimaging studies indicating that static pictures portraying gestures activate brain regions associated with an observation-execution matching system.

  16. Static viscoelasticity of biomass polyethylene composites

    Science.gov (United States)

    Yang, Keyan; Cai, Hongzhen; Yi, Weiming; Zhang, Qingfa; Zhao, Kunpeng

    The biomass polyethylene composites filled with poplar wood flour, rice husk, cotton stalk or corn stalk were prepared by extrusion molding. The static viscoelasticity of composites was investigated by the dynamic thermal mechanical analyzer (DMA). Through the stress-strain scanning, it is found that the linear viscoelasticity interval of composites gradually decreases as the temperature rises, and the critical stress and strain values are 0.8 MPa and 0.03% respectively. The experiment shows that as the temperature rises, the creep compliance of biomass polyethylene composites is increased; under the constant temperature, the creep compliance decreases with the increase of content of biomass and calcium carbonate. The biomass and calcium carbonate used to prepare composites as filler can improve damping vibration attenuation and reduce stress deformation of composites. The stress relaxation modulus of composites is reduced and the relaxation rate increases at the higher temperature. The biomass and calcium carbonate used to prepare composites as filler not only can reduce costs, but also can increase stress relaxation modulus and improve the size thermostability of composites. The corn stalk is a good kind of biomass raw material for composites since it can improve the creep resistance property and the stress relaxation resistance property of composites more effectively than other three kinds of biomass (poplar wood flour, rice husk and cotton stalk).

  17. Beyond Erikson's Eight Stages.

    Science.gov (United States)

    Whitney, Ruth

    1979-01-01

    Erik Erikson has described eight stages of the healthy personality. This essay offers a revised version of the eight stages. Although most individuals develop through the eight stages, each is personally unique because patterns of fluctuation between safety and growth differ from one individual to another. (Author)

  18. Cervical Cancer Stage IIIA

    Science.gov (United States)

    ... hyphen, e.g. -historical Searches are case-insensitive Cervical Cancer Stage IIIA Add to My Pictures View /Download : ... 1275x1275 View Download Large: 2550x2550 View Download Title: Cervical Cancer Stage IIIA Description: Stage IIIA cervical cancer; drawing ...

  19. Cervical Cancer Stage IVA

    Science.gov (United States)

    ... hyphen, e.g. -historical Searches are case-insensitive Cervical Cancer Stage IVA Add to My Pictures View /Download : ... 1575x1200 View Download Large: 3150x2400 View Download Title: Cervical Cancer Stage IVA Description: Stage IVA cervical cancer; drawing ...

  20. Cervical Cancer Stage IVB

    Science.gov (United States)

    ... hyphen, e.g. -historical Searches are case-insensitive Cervical Cancer Stage IVB Add to My Pictures View /Download : ... 1200x1305 View Download Large: 2400x2610 View Download Title: Cervical Cancer Stage IVB Description: Stage IVB cervical cancer; drawing ...

  1. Cervical Cancer Stage IIIB

    Science.gov (United States)

    ... hyphen, e.g. -historical Searches are case-insensitive Cervical Cancer Stage IIIB Add to My Pictures View /Download : ... 1425x1326 View Download Large: 2850x2651 View Download Title: Cervical Cancer Stage IIIB Description: Stage IIIB cervical cancer; drawing ...

  2. Cervical Cancer Stage IB

    Science.gov (United States)

    ... hyphen, e.g. -historical Searches are case-insensitive Cervical Cancer Stage IB Add to My Pictures View /Download : ... 1613x1200 View Download Large: 3225x2400 View Download Title: Cervical Cancer Stage IB Description: Stage IB1 and IB2 cervical ...

  3. Cervical Cancer Stage IA

    Science.gov (United States)

    ... historical Searches are case-insensitive Cervical Cancer Stage IA Add to My Pictures View /Download : Small: 720x576 ... Large: 3000x2400 View Download Title: Cervical Cancer Stage IA Description: Stage IA1 and IA2 cervical cancer; drawing ...

  4. DNA-Nanotechnology-Enabled Chiral Plasmonics: From Static to Dynamic.

    Science.gov (United States)

    Zhou, Chao; Duan, Xiaoyang; Liu, Na

    2017-12-19

    The development of DNA nanotechnology, especially the advent of DNA origami, has made DNA ideally suited to construct nanostructures with unprecedented complexity and arbitrariness. As a fully addressable platform, DNA origami can be used to organize discrete entities in space through DNA hybridization with nanometer accuracy. Among a variety of functionalized particles, metal nanoparticles such as gold nanoparticles (AuNPs) feature an important pathway to endow DNA-origami-assembled nanostructures with tailored optical functionalities. When metal particles are placed in close proximity, their particle plasmons, i.e., collective oscillations of conduction electrons, can be coupled together, giving rise to a wealth of interesting optical phenomena. Nevertheless, characterization methods that can read out the optical responses from plasmonic nanostructures composed of small metal particles, and especially can optically distinguish in situ their minute conformation changes, are very few. Circular dichroism (CD) spectroscopy has proven to be a successful means to overcome these challenges because of its high sensitivity in discrimination of three-dimensional conformation changes. In this Account, we discuss a variety of static and dynamic chiral plasmonic nanostructures enabled by DNA nanotechnology. In the category of static plasmonic systems, we first show chiral plasmonic nanostructures based on spherical AuNPs, including plasmonic helices, toroids, and tetramers. To enhance the CD responses, anisotropic gold nanorods with larger extinction coefficients are utilized to create chiral plasmonic crosses and helical superstructures. Next, we highlight the inevitable evolution from static to dynamic plasmonic systems along with the fast development of this interdisciplinary field. Several dynamic plasmonic systems are reviewed according to their working mechanisms. We first elucidate a reconfigurable plasmonic cross structure that can execute DNA-regulated conformational

  5. Dynamic XRD, Shock and Static Compression of CaF2

    Science.gov (United States)

    Kalita, Patricia; Specht, Paul; Root, Seth; Sinclair, Nicholas; Schuman, Adam; White, Melanie; Cornelius, Andrew; Smith, Jesse; Sinogeikin, Stanislav

    2017-06-01

    The high-pressure behavior of CaF2 is probed with x-ray diffraction (XRD) combined with both dynamic compression, using a two-stage light gas gun, and static compression, using diamond anvil cells. We use XRD to follow the unfolding of a shock-driven, fluorite to cotunnite phase transition, on the timescale of nanoseconds. The dynamic behavior of CaF2 under shock loading is contrasted with that under static compression. This work leverages experimental capabilities at the Advanced Photon Source: dynamic XRD and shock experiments at the Dynamic Compression Sector, as well as XRD and static compression in diamond anvil cell at the High-Pressure Collaborative Access Team. These experiments and cross-platform comparisons, open the door to an unprecedented understanding of equations of state and phase transitions at the microstructural level and at different time scales and will ultimately improve our capability to simulate the behavior of materials at extreme conditions. Sandia National Laboratories is a multi-mission laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

  6. Literature review Quasi-static and Dynamic pile load tests : Primarily report on non-static pile load tests

    NARCIS (Netherlands)

    Huy, N.Q.

    2010-01-01

    Pile testing, which plays an importance role in the field of deep foundation design, is performed by static and non-static methods to provide information about the following issues: (Poulos, 1998) - The ultimate capacity of a single pile. - The load-displacement behavior of a pile. - The performance

  7. Cetuximab, Cisplatin, and Radiation Therapy in Treating Patients With Stage IB, Stage II, Stage III, or Stage IVA Cervical Cancer

    Science.gov (United States)

    2014-12-29

    Cervical Adenocarcinoma; Cervical Adenosquamous Carcinoma; Cervical Small Cell Carcinoma; Cervical Squamous Cell Carcinoma; Stage IB Cervical Cancer; Stage IIA Cervical Cancer; Stage IIB Cervical Cancer; Stage III Cervical Cancer; Stage IVA Cervical Cancer

  8. Static mechanical properties of buffer material

    International Nuclear Information System (INIS)

    Takaji, Kazuhiko; Suzuki, Hideaki

    1999-11-01

    The buffer material is expected to maintain its low water permeability, self-sealing properties, radionuclides adsorption and retardation properties, thermal conductivity, chemical buffering properties, overpack supporting properties, stress buffering properties, etc. over a long period of time. Natural clay is mentioned as a material that can relatively satisfy above. Among the kinds of natural clay, bentonite when compacted is superior because (i) it has exceptionally low water permeability and properties to control the movement of water in buffer, (ii) it fills void spaces in the buffer and fractures in the host rock as it swells upon water uptake, (iii) it has the ability to exchange cations and to adsorb cationic radioelements. In order to confirm these functions for the purpose of safety assessment, it is necessary to evaluate buffer properties through laboratory tests and engineering-scale tests, and to make assessments based on the ranges in the data obtained. This report describes the procedures, test conditions, results and examinations on the buffer material of unconfined compression tests, one-dimensional consolidation tests, consolidated-undrained triaxial compression tests and consolidated-undrained triaxial creep tests that aim at getting hold of static mechanical properties. We can get hold of the relationship between the dry density and tensile stress etc. by Brazilian tests, between the dry density and unconfined compressive strength etc. by unconfined compression tests, between the consolidation stress and void ratio etc. by one-dimensional consolidation tests, the stress pass of each effective confining pressure etc. by consolidated-undrained triaxial compression tests and the axial strain rate with time of each axial stress etc. by consolidated-undrained triaxial creep tests. (author)

  9. Comparing Stage Presence and Virtual Reality Presence

    Directory of Open Access Journals (Sweden)

    Sebastian Xavier Samur

    2016-05-01

    Full Text Available Reflecting on the impending release of new Head Mounted Display virtual reality (VR technologies, the article examines definitions and techniques for digital presence, and compares them with research into stage presence. It opens with an outline of definitions of digital presence, comparing them with Cormac Power’s fictional, auratic, and literal modes of presence in performance. The article then looks at techniques used in VR and on stage to achieve presence. Finally, performance examples that use virtual reality technologies are presented. The article concludes that even if the technology falls short, discourse on digital presence is useful in providing insights into presence on stage.

  10. Pre-exposure to moving form enhances static form sensitivity.

    Directory of Open Access Journals (Sweden)

    Thomas S A Wallis

    Full Text Available BACKGROUND: Motion-defined form can seem to persist briefly after motion ceases, before seeming to gradually disappear into the background. Here we investigate if this subjective persistence reflects a signal capable of improving objective measures of sensitivity to static form. METHODOLOGY/PRINCIPAL FINDINGS: We presented a sinusoidal modulation of luminance, masked by a background noise pattern. The sinusoidal luminance modulation was usually subjectively invisible when static, but visible when moving. We found that drifting then stopping the waveform resulted in a transient subjective persistence of the waveform in the static display. Observers' objective sensitivity to the position of the static waveform was also improved after viewing moving waveforms, compared to viewing static waveforms for a matched duration. This facilitation did not occur simply because movement provided more perspectives of the waveform, since performance following pre-exposure to scrambled animations did not match that following pre-exposure to smooth motion. Observers did not simply remember waveform positions at motion offset, since removing the waveform before testing reduced performance. CONCLUSIONS/SIGNIFICANCE: Motion processing therefore interacts with subsequent static visual inputs in a way that can improve performance in objective sensitivity measures. We suggest that the brief subjective persistence of motion-defined forms that can occur after motion offsets is a consequence of the decay of a static form signal that has been transiently enhanced by motion processing.

  11. Early stage vision in schizophrenia and schizotypal personality disorder.

    Science.gov (United States)

    O'Donnell, Brian F; Bismark, Andrew; Hetrick, William P; Bodkins, Misty; Vohs, Jenifer L; Shekhar, Anantha

    2006-09-01

    Previous studies of visual perception have reported deficits in contrast sensitivity and dot motion discrimination in schizophrenia. We tested whether these deficits also appear in schizotypal personality disorder (SPD). SPD appears to be genetically and symptomatically related to schizophrenia, but without the marked psychosocial impairment associated with psychotic disorders. The present study investigated contrast sensitivity for moving and static gratings, form discrimination and dot motion discrimination in 24 patients with schizophrenia or schizoaffective disorder (SZ), 16 individuals with SPD, and 40 control subjects. SZ, but not SPD subjects, showed impairments on tests of contrast sensitivity for static and moving gratings, form discrimination in noise, and dot motion discrimination. Visual performance did not differ between medicated SZ patients and patients withdrawn from medication. These results confirm early stage visual deficits in schizophrenia regardless of medication status. SPD subjects, in contrast, show intact early stage visual processing despite the presence of marked schizotypal symptoms.

  12. Comparison of growth kinetics between static and dynamic cultures of human induced pluripotent stem cells.

    Science.gov (United States)

    Kato, Yuma; Kim, Mee-Hae; Kino-Oka, Masahiro

    2018-02-02

    Understanding the fundamental mechanisms that govern the growth kinetics of human induced pluripotent stem cells (hiPSCs) contributes to culture design strategies to improve large-scale production. Two hiPSC lines (Tic and 253G1) were cultured under static and dynamic suspension conditions, and growth kinetics were compared during early (24-48 h), middle (48-72 h), and late (72-96 h) stages. In 2D static culture, similar growth profiles were observed for both hiPSC lines. However, there were significant differences in growth profile patterns and aggregate morphologies between hiPSC lines grown in 3D static and dynamic cultures. Based on immunostaining comparing the two hiPSC lines, surface distribution of collagen type I was observed in aggregates of the Tic line, but not in those of the 253G1 line. Compared to that in 3D static culture, the numbers of cells at 96 h were significantly decreased in 3D dynamic culture. The apparent specific growth rate (μ app ) of the Tic line was maintained continuously throughout culture, whereas that of the 253G1 line decreased gradually with culture until the late phase, at which time this parameter was reduced to μ app  = (0.85 ± 0.71) × 10 -2  h -1 . This indicates that during the growth of hiPSCs in 3D dynamic culture, cells were damaged by liquid flow, which disrupted the cell-synthesized extracellular matrix (ECM). These results demonstrate that cell-synthesized ECM is an important factor affecting cell growth and morphology, and that changes to the ECM within aggregates lead to reduced growth abilities in dynamic culture. Copyright © 2018 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

  13. Effect of static foot posture on the dynamic stiffness of foot joints during walking.

    Science.gov (United States)

    Sanchis-Sales, E; Sancho-Bru, J L; Roda-Sales, A; Pascual-Huerta, J

    2018-03-17

    The static foot posture has been related to the development of lower limb injuries. This study aimed to investigate the dynamic stiffness of foot joints during gait in the sagittal plane to understand the role of the static foot posture in the development of injuries. Seventy healthy adult male subjects with different static postures, assessed by the Foot Posture Index (FPI) (30 normal, 20 highly pronated and 20 highly supinated), were recruited. Kinematic and kinetic data were recorded using an optical motion capture system and a pressure platform, and dynamic stiffness at the different stages of the stance was calculated from the slopes of the linear regression on the flexion moment-angle curves. The effect of foot type on dynamic stiffness and on ranges of motion and moments was analysed using ANOVAs and post-hoc tests, and linear correlation between dynamic stiffness and FPI was also tested. Highly pronated feet showed a significantly smaller range of motion at the ankle and metatarsophalangeal joints and also a larger range of moments at the metatarsophalangeal joint than highly supinated feet. Dynamic stiffness during propulsion was significantly greater at all foot joints for highly pronated feet, with positive significant correlations with the squared FPI. Highly supinated feet showed greater dynamic stiffness than normal feet, although to a lesser extent. Highly pronated feet during normal gait experienced the greatest decrease in the dorsiflexor moments during propulsion, normal feet being the most balanced regarding work generated and absorbed. Extreme static foot postures show greater dynamic stiffness during propulsion and greater absorbed work, which increases the risk of developing injuries. The data presented may be used when designing orthotics or prostheses, and also when planning surgery that modifies joint stiffness. Copyright © 2018 Elsevier B.V. All rights reserved.

  14. Systematic review of biological effects of exposure to static electric fields. Part II: Invertebrates and plants.

    Science.gov (United States)

    Schmiedchen, Kristina; Petri, Anne-Kathrin; Driessen, Sarah; Bailey, William H

    2018-01-01

    The construction of high-voltage direct current (HVDC) lines for the long-distance transport of energy is becoming increasingly popular. This has raised public concern about potential environmental impacts of the static electric fields (EF) produced under and near HVDC power lines. As the second part of a comprehensive literature analysis, the aim of this systematic review was to assess the effects of static EF exposure on biological functions in invertebrates and plants and to provide the basis for an environmental impact assessment of such exposures. The Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) was used to guide the methodological conduct and reporting. Thirty-three studies - 14 invertebrate and 19 plant studies - met the eligibility criteria and were included in this review. The reported behavioral responses of insects and planarians upon exposure strongly suggest that invertebrates are able to perceive the presence of a static EF. Many other studies reported effects on physiological functions that were expressed as, for example, altered metabolic activity or delayed reproductive and developmental stages in invertebrates. In plants, leaf damage, alterations in germination rates, growth and yield, or variations in the concentration of essential elements, for example, have been reported. However, these physiological responses and changes in plant morphology appear to be secondary to surface stimulation by the static EF or caused by concomitant parameters of the electrostatic environment. Furthermore, all of the included studies suffered from methodological flaws, which lowered credibility in the results. At field levels encountered from natural sources or HVDC lines ( 35kV/m), adverse effects on physiology and morphology, presumably caused by corona-action, appear to be more likely. Higher quality studies are needed to unravel the role of air ions, ozone, nitric oxide and corona current on alterations in physiological functions

  15. EFFECTIVENESS OF INSTUMENTAL ASSISTED SOFT TISSUE MOBILIZATION TECHNIQUE WITH STATIC STRETCHING IN SUBJECTS WITH PLANTAR FASCIITIS

    Directory of Open Access Journals (Sweden)

    Vinod Babu. K

    2014-08-01

    Full Text Available Background: Instrumental assisted soft tissue mobilization and static stretching found to be effective in plantar fasciitis, however the combined effectiveness of these techniques were unknown. The purpose of this study is to find the effect of Instrumental assisted soft tissue mobilization technique for plantar fascia combined with static stretching of triceps surae for subjects with chronic stage of Plantar Fasciitis on pain intensity, ankle dorsiflexion range of motion and functional disability. Methods: An experimental study design, selected subjects with chronic Plantar Fasciitis randomized subjects into each Study and Control group. Total of 40 subject’s data who completed study, 20 in each group, was used for analysis. Control group received conventional exercise while Study group received conventional exercises with Instrumental assisted soft tissue mobilization combined with static stretching of triceps surae muscle. Outcome measurements such as Intensity of pain using Numerical Pain Rating Scale-101 (NPRS-101, function disability using Foot Function Index Pain Subscale (FFI and ankle dorsiflexion active range of motion using Goniometer was measured before and after 2 weeks of intervention. Results: There is statistically significant improvement in means of NRS-101, ankle dorsiflexion active range of motion and Foot Function Index Pain Subscale after intervention in both groups. When the post-intervention means were compared between Study and Control group after 2 weeks of treatment there is statistically significant difference in means between the groups whereas study group showed greater percentage of improvement than control group. Conclusion: It is concluded that Instrumental assisted soft tissue mobilization technique combined with static stretching of triceps surae muscle is significantly effective than conventional exercises on reducing pain, improving ankle dorsiflexion range of motion and functional disability for subjects

  16. Static Scheduling of Periodic Hardware Tasks with Precedence and Deadline Constraints on Reconfigurable Hardware Devices

    Directory of Open Access Journals (Sweden)

    Ikbel Belaid

    2011-01-01

    Full Text Available Task graph scheduling for reconfigurable hardware devices can be defined as finding a schedule for a set of periodic tasks with precedence, dependence, and deadline constraints as well as their optimal allocations on the available heterogeneous hardware resources. This paper proposes a new methodology comprising three main stages. Using these three main stages, dynamic partial reconfiguration and mixed integer programming, pipelined scheduling and efficient placement are achieved and enable parallel computing of the task graph on the reconfigurable devices by optimizing placement/scheduling quality. Experiments on an application of heterogeneous hardware tasks demonstrate an improvement of resource utilization of 12.45% of the available reconfigurable resources corresponding to a resource gain of 17.3% compared to a static design. The configuration overhead is reduced to 2% of the total running time. Due to pipelined scheduling, the task graph spanning is minimized by 4% compared to sequential execution of the graph.

  17. Static and dynamic magnetic properties of densely packed magnetic nanowire arrays

    DEFF Research Database (Denmark)

    Dmytriiev, O.; Al-Jarah, U.A.S.; Gangmei, P.

    2013-01-01

    between experimental and simulated spectra are observed when the field is applied perpendicular to the nanowire axes. The dependence of the magnetic excitation spectra upon the array packing density is explored, and dispersion curves for spin waves propagating within the array parallel to the nanowire...... axis are presented. Finally, a tunneling of end modes through the middle region of the nanowires was observed. The tunneling is more efficient for wires forming densely packed arrays, as a result of the extended penetration of the dynamic demagnetizing fields into the middle of the wires and due...... to the lowering of the tunneling barrier by the static demagnetizing field of the array....

  18. Modern control of static var compensator for power system stability enhancement

    Directory of Open Access Journals (Sweden)

    Stelian-Emilian Oltean

    2012-06-01

    Full Text Available The effects of shunt compensation on power system transmission stability and modern approach of the reactive power control scheme have been investigated in this paper. Reactive power compensation is realized in shunt connection with two components: thyristor controlled reactor (TCR and thyristor switched capacitor (TSC. A special attention has been given in the following paragraphs to a modern control approach for power system stability enhancement which uses fuzzy logic. In the final part of the paper the modern control block scheme of static VAR compensator for reactive power in transmission systems is presented.

  19. Comparison of methods for static charge energy harvesting on aircraft

    Science.gov (United States)

    Kiziroglou, M. E.; Becker, Th.; Yeatman, E. M.; Schmid, U.; Evans, J. W.; Wright, P. K.

    2017-05-01

    In this paper, the possibility of using the static charge that accumulates on aircraft during flight as a source to power monitoring sensors is examined. The assessed methods include using a pair of materials with different air-flow charging rates, contact discharging of the fuselage to neutral metallic bodies, charge motion induction by the fuselage field and inductive harvesting of fuselage-to-air corona discharges at static discharge wicks. The installation and potential advantages of each method are discussed. The feasibility of directly charging a storage capacitor from accumulated static charge is studied experimentally, demonstrating a voltage of 25V on a 25nF capacitor.

  20. Granular flow in static mixers by coupled DEM/CFD approach

    Directory of Open Access Journals (Sweden)

    Pezo Lato

    2016-01-01

    Full Text Available The mixing process greatly influence the mixing efficiency, as well as the quality and the price of the intermediate and/or the final product. Static mixer is used for premixing action before the main mixing process, for significant reduction of mixing time and energy consumption. This type of premixing action is not investigated in detail in the open literature. In this article, the novel numerical approach called Discrete Element Method is used for modelling of granular flow in multiple static mixer applications (1 - 3 Komax or Ross mixing elements were utilized, while the Computational Fluid Dynamic method was chosen for fluid flow modelling, using the Eulerian multiphase model. The main aim of this article is to predict the behaviour of granules being gravitationally transported in different mixer configuration and to choose the best configuration of the mixer taking into account the total particle path, the number of mixing elements and the quality of the obtained mixture. The results of the numerical simulations in the static mixers were compared to experimental results, the mixing quality is examined by RSD (relative standard deviation criterion, and the effects on the mixer type and the number of mixing elements on mixing process were studied. The effects of the mixer type and the number of mixing elements on mixing process were studied using analysis of variance (ANOVA. Mathematical modelling is used for optimization of number of Ross and Komax segments in mixer in order to gain desirable mixing results. [Projekat Ministarstva nauke Republike Srbije, br. TR31055

  1. An investigation of the static and dynamic behavior of electrically actuated rectangular microplates

    KAUST Repository

    Saghir, S.

    2016-06-16

    We present an investigation of the static and dynamic behavior of the nonlinear von-Karman plates when actuated by the nonlinear electrostatic forces. The investigation is based on a reduced order model developed using the Galerkin method, which rely on modeshapes and in-plane shape functions extracted using a finite element method. In this study, a fully clamped microplate is considered. We investigate the static behavior and the effect of different non-dimensional design parameters. The static results are validated by comparison with the results calculated by a finite element model. The forced-vibration response of the plate is then investigated when the plate is excited by a harmonic AC load superimposed to a DC load. The dynamic behavior is examined near the primary and secondary (superharmonic and subharmonic) resonances. The microplate shows a strong hardening behavior due to the cubic nonlinearity of mid-plane stretching. However, the behavior switches to softening as the DC load is increased. Finally, near-square plates are studied to understand the effect of geometric imperfections of microplates.

  2. Static black holes with axial symmetry in asymptotically AdS4 spacetime

    Science.gov (United States)

    Kichakova, Olga; Kunz, Jutta; Radu, Eugen; Shnir, Yasha

    2016-02-01

    The known static electrovacuum black holes in a globally AdS4 background have an event horizon which is geometrically a round sphere. In this work we argue that the situation is different in models with matter fields possessing an explicit dependence on the azimuthal angle φ , which, however, does not manifest at the level of the energy-momentum tensor. As a result, the full solutions are axially symmetric only, possessing a single (timelike) Killing vector field. Explicit examples of such static black holes are constructed in Einstein-(complex) scalar field and Einstein-Yang-Mills theories. The basic properties of these solutions are discussed, looking for generic features. For example, we notice that the horizon has an oblate spheroidal shape for solutions with a scalar field and a prolate one for black holes with Yang-Mills fields. The deviation from sphericity of the horizon geometry manifests itself in the holographic stress tensor. Finally, based on the results obtained in the probe limit, we conjecture the existence in Einstein-Maxwell theory of static black holes with axial symmetry only.

  3. Crack Propagation Calculations for Optical Fibers under Static Bending and Tensile Loads Using Continuum Damage Mechanics.

    Science.gov (United States)

    Chen, Yunxia; Cui, Yuxuan; Gong, Wenjun

    2017-11-15

    Static fatigue behavior is the main failure mode of optical fibers applied in sensors. In this paper, a computational framework based on continuum damage mechanics (CDM) is presented to calculate the crack propagation process and failure time of optical fibers subjected to static bending and tensile loads. For this purpose, the static fatigue crack propagation in the glass core of the optical fiber is studied. Combining a finite element method (FEM), we use the continuum damage mechanics for the glass core to calculate the crack propagation path and corresponding failure time. In addition, three factors including bending radius, tensile force and optical fiber diameter are investigated to find their impacts on the crack propagation process and failure time of the optical fiber under concerned situations. Finally, experiments are conducted and the results verify the correctness of the simulation calculation. It is believed that the proposed method could give a straightforward description of the crack propagation path in the inner glass core. Additionally, the predicted crack propagation time of the optical fiber with different factors can provide effective suggestions for improving the long-term usage of optical fibers.

  4. Some remarks on static, creep and fatigue flexural strength of satin woven CFRP laminates

    Energy Technology Data Exchange (ETDEWEB)

    Miyano, Y.; McMurry, M.K. [Kanazawa Institute of Technology (Japan); Muki, R. [Univ. of California, Los Angeles, CA (United States)

    1995-12-31

    This paper deals with the time-temperature dependent flexural strength of a satin-woven CFRP laminate having a matrix resin with a high glass transition temperature of T{sub g} = 236/C under static, creep and fatigue loading by 3-point bending tests. Static tests were conducted at various points in a wide range of deflection rates and temperatures. The creep and fatigue tests were carried out at various constant temperatures; the fatigue test was conducted at two frequencies. The results of the experimental study are as follows. The flexural strength of the CFRP laminates for all three loading types is time-temperature dependent even near room temperature well below T{sub g}. The time and temperature superposition principle for the matrix resin also holds for the flexural strength of the CFRP laminates. The fracture modes are almost the same for the three loading types under all conditions tested. Finally, we propose a method for predicting the flexural fatigue strength for a given number of cycles to failure at an arbitrary temperature, frequency and stress ratio based on the current experimental findings and considering the relationships among the static, creep and fatigue flexural strengths.

  5. Multiple stage railgun

    International Nuclear Information System (INIS)

    Aaland, K.; Hawke, R.S.; Scudder, J.K.

    1982-01-01

    A multiple stage magnetic railgun accelerator for accelerating a projectile by movement of a plasma arc along the rails. The railgun is divided into a plurality of successive rail stages which are sequentially energized by separate energy sources as the projectile moves through the bore of the railgun. Propagation of energy from an energized rail stage back towards the breech end of the railgun can be prevented by connection of the energy sources to the rails through isolation diodes. Propagation of energy from an energized rail stage back towards the breech end of the railgun can also be prevented by dividing the rails into electrically isolated rail sections. In such case means are used to extinguish the arc at the end of each energized stage and a fuse or laser device is used to initiate a new plasma arc in the next energized rail stage

  6. Staged decision making based on probabilistic forecasting

    Science.gov (United States)

    Booister, Nikéh; Verkade, Jan; Werner, Micha; Cranston, Michael; Cumiskey, Lydia; Zevenbergen, Chris

    2016-04-01

    Flood forecasting systems reduce, but cannot eliminate uncertainty about the future. Probabilistic forecasts explicitly show that uncertainty remains. However, as - compared to deterministic forecasts - a dimension is added ('probability' or 'likelihood'), with this added dimension decision making is made slightly more complicated. A technique of decision support is the cost-loss approach, which defines whether or not to issue a warning or implement mitigation measures (risk-based method). With the cost-loss method a warning will be issued when the ratio of the response costs to the damage reduction is less than or equal to the probability of the possible flood event. This cost-loss method is not widely used, because it motivates based on only economic values and is a technique that is relatively static (no reasoning, yes/no decision). Nevertheless it has high potential to improve risk-based decision making based on probabilistic flood forecasting because there are no other methods known that deal with probabilities in decision making. The main aim of this research was to explore the ways of making decision making based on probabilities with the cost-loss method better applicable in practice. The exploration began by identifying other situations in which decisions were taken based on uncertain forecasts or predictions. These cases spanned a range of degrees of uncertainty: from known uncertainty to deep uncertainty. Based on the types of uncertainties, concepts of dealing with situations and responses were analysed and possible applicable concepts where chosen. Out of this analysis the concepts of flexibility and robustness appeared to be fitting to the existing method. Instead of taking big decisions with bigger consequences at once, the idea is that actions and decisions are cut-up into smaller pieces and finally the decision to implement is made based on economic costs of decisions and measures and the reduced effect of flooding. The more lead-time there is in

  7. Static Air Support Surfaces to Prevent Pressure Injuries: A Multicenter Cohort Study in Belgian Nursing Homes.

    Science.gov (United States)

    Serraes, Brecht; Beeckman, Dimitri

    2016-01-01

    The aim of this study was to investigate the incidence and risk factors for developing pressure injuries (PIs) in patients placed on a static air support surfaces: mattress overlay, heel wedge, and seat cushion. Multicenter cohort study. The sample comprised 176 residents; their mean age was 87 (SD = 6.76) years; their mean Braden Scale score was 14 (SD = 2.54). The study was performed on a convenience sample of 6 nursing homes in Belgium. Data were collected on 23 care units. The primary outcome measure, cumulative PI incidence (category [stage] II-IV) over a 30-day observation period, was calculated. Pressure injury occurrence was defined according to the 2014 European and US National Pressure Injury Advisory panels, Pan Pacific Pressure Injury Alliance classification system. The PI incidence for category (stage) II-IV was 5.1%. Six residents (3.4%) developed a category II PI, and 3 (1.7%) developed a category III PI; no category IV ulcers occurred. No significant risk factors for category II-IV PIs were identified using multivariate logistic regression. Time of sitting in a chair was found to be a risk factor for development of nonblanchable erythema (category I PI) (odds ratio = 21.608; 95% confidence interval [CI], 20.510-22.812; P = .013). The median time to develop a category II-IV PI was 16 days (interquartile range = 2-26). The interrater reliability between the observations of the researcher and nurses on-site was almost perfect (0.86; 95% CI, 0.81-0.91). We found a low incidence of PIs when using a static air overlay mattress for patients at risk in a nursing home population. Static air support surfaces, alongside patient-tailored patient repositioning protocols, should be considered to prevent PIs in this patient population.

  8. Static sampling of dynamic processes - a paradox?

    Science.gov (United States)

    Mälicke, Mirko; Neuper, Malte; Jackisch, Conrad; Hassler, Sibylle; Zehe, Erwin

    2017-04-01

    Environmental systems monitoring aims at its core at the detection of spatio-temporal patterns of processes and system states, which is a pre-requisite for understanding and explaining their baffling heterogeneity. Most observation networks rely on distributed point sampling of states and fluxes of interest, which is combined with proxy-variables from either remote sensing or near surface geophysics. The cardinal question on the appropriate experimental design of such a monitoring network has up to now been answered in many different ways. Suggested approaches range from sampling in a dense regular grid using for the so-called green machine, transects along typical catenas, clustering of several observations sensors in presumed functional units or HRUs, arrangements of those cluster along presumed lateral flow paths to last not least a nested, randomized stratified arrangement of sensors or samples. Common to all these approaches is that they provide a rather static spatial sampling, while state variables and their spatial covariance structure dynamically change in time. It is hence of key interest how much of our still incomplete understanding stems from inappropriate sampling and how much needs to be attributed to an inappropriate analysis of spatial data sets. We suggest that it is much more promising to analyze the spatial variability of processes, for instance changes in soil moisture values, than to investigate the spatial variability of soil moisture states themselves. This is because wetting of the soil, reflected in a soil moisture increase, is causes by a totally different meteorological driver - rainfall - than drying of the soil. We hence propose that the rising and the falling limbs of soil moisture time series belong essentially to different ensembles, as they are influenced by different drivers. Positive and negative temporal changes in soil moisture need, hence, to be analyzed separately. We test this idea using the CAOS data set as a benchmark

  9. Turbine stage model

    International Nuclear Information System (INIS)

    Kazantsev, A.A.

    2009-01-01

    A model of turbine stage for calculations of NPP turbine department dynamics in real time was developed. The simulation results were compared with manufacturer calculations for NPP low-speed and fast turbines. The comparison results have shown that the model is valid for real time simulation of all modes of turbines operation. The model allows calculating turbine stage parameters with 1% accuracy. It was shown that the developed turbine stage model meets the accuracy requirements if the data of turbine blades setting angles for all turbine stages are available [ru

  10. Galactic orbital motions of star clusters: static versus semicosmological time-dependent Galactic potentials

    Science.gov (United States)

    Haghi, Hosein; Zonoozi, Akram Hasani; Taghavi, Saeed

    2015-07-01

    In order to understand the orbital history of Galactic halo objects, such as globular clusters, authors usually assume a static potential for our Galaxy with parameters that appear at the present day. According to the standard paradigm of galaxy formation, galaxies grow through a continuous accretion of fresh gas and a hierarchical merging with smaller galaxies from high redshift to the present day. This implies that the mass and size of disc, bulge, and halo change with time. We investigate the effect of assuming a live Galactic potential on the orbital history of halo objects and its consequences on their internal evolution. We numerically integrate backwards the equations of motion of different test objects located in different Galactocentric distances in both static and time-dependent Galactic potentials in order to see if it is possible to discriminate between them. We show that in a live potential, the birth of the objects, 13 Gyr ago, would have occurred at significantly larger Galactocentric distances, compared to the objects orbiting in a static potential. Based on the direct N-body calculations of star clusters carried out with collisional N-body code, NBODY6, we also discuss the consequences of the time-dependence of a Galactic potential on the early- and long-term evolution of star clusters in a simple way, by comparing the evolution of two star clusters embedded in galactic models, which represent the galaxy at present and 12 Gyr ago, respectively. We show that assuming a static potential over a Hubble time for our Galaxy as it is often done, leads to an enhancement of mass-loss, an overestimation of the dissolution rates of globular clusters, an underestimation of the final size of star clusters, and a shallower stellar mass function.

  11. Efeito da densidade de povoamento na produtividade final em carpas (Cyprinus carpio var specularis em fase de engorda, durante o verão Effect of population density on the productivity of carp (Cyprinus carpio var specularis, in the fattening stage, during the summer

    Directory of Open Access Journals (Sweden)

    Álvaro Graeff

    2000-06-01

    Full Text Available O objetivo desta pesquisa foi estudar o efeito da densidade de povoamento na produtividade final, em carpas na fase de engorda, no período de verão. O delineamento foi inteiramente casualizado com três tratamentos (1; 0,5; e 0,33 peixes/m² e três repetições. Os peixes foram estocados com peso e comprimento médios de 2,40 g e 5,35; 5,40 e 5,39 cm, respectivamente, nos tratamentos 1, 2 e 3, com 45 dias de idade. As dietas foram formuladas com 27% PB e 2925 kcal/kg de ração, sendo fornecidas diariamente, na quantidade de 3% do peso vivo. O comportamento dos tratamentos foi estudado por intermédio da análise de regressão. Os resultados para o comprimento e peso dos peixes foram 25,68; 28,66; e 31,21 cm e 255,00; 424,00; e 519,66 g, respectivamente. Os tratamentos 1 e 3 apresentaram modelo de regressão linear diferente do tratamento 2, que apresentou modelo quadrático. Na biomassa total, os resultados foram 1881; 1512; e 1302 kg/ha/período e os modelos de regressão significativos para os tratamentos 1e 3 foram lineares e para o tratamento 2 quadrático. A conversão alimentar apresentou modelo de regressão linear para todos tratamentos. Em condições similares, podem-se recomendar todas densidades sugeridas, com base na produção final e sobrevivência.This study aimed to evaluate impact of stocking density on final productivity in the production of mirror common carp in fattening stage, during the summer. A completely randomized design with three treatments (1, .5, .33 fishes/m² and three replicates was used. The fish were stocked with an average weight of 2.40 g and average length of 5.35, 5.40 and 5.39 cm, respectively, in the treatments 1, 2 and 3, with 45 days of age. The diets were formulated with 27% CP and 2925 kcal/kg of diet and supplied daily at a rate of 3% of body weight. Regression analysis was used to evaluate the behavior of each treatment. For the fish lengths, the results were 25.68, 28.66 and 31.21 cm

  12. Effects of Static Stretching and Playing Soccer on Knee Laxity

    NARCIS (Netherlands)

    Baumgart, Christian; Gokeler, Alli; Donath, Lars; Hoppe, Matthias W.; Freiwald, Juergen

    2015-01-01

    Objective: This study investigated exercise-induced effects of static stretching and playing soccer on anterior tibial translation (ATT) of the knee joint. Design: Randomized controlled trial. Setting: University biomechanics laboratory. Participants: Thirty-one athletes were randomly assigned into

  13. Measurement of dynamic and static radiation force on a sphere.

    Science.gov (United States)

    Chen, Shigao; Silva, Glauber T; Kinnick, Randall R; Greenleaf, James F; Fatemi, Mostafa

    2005-05-01

    Dynamic radiation force from ultrasound has found increasing applications in elasticity imaging methods such as vibro-acoustography. Radiation force that has both static and dynamic components can be produced by interfering two ultrasound beams of slightly different frequencies. This paper presents a method to measure both static and dynamic components of the radiation force on a sphere suspended by thin threads in water. Due to ultrasound radiation force, the sphere deflects to an equilibrant position and vibrates around it. The static radiation force is estimated from the deflection of the sphere. The dynamic radiation force is estimated from the calculated radiation impedance of the sphere and its vibration speed measured by a laser vibrometer. Experimental results on spheres of different size, vibrated at various frequencies, confirm the theoretical prediction that the dynamic and static radiation force on a sphere have approximately equal magnitudes [G. T. Silva, Phys. Rev. E 71, 056617 (2005)].

  14. Einstein's conversion from his static to an expanding universe

    Science.gov (United States)

    Nussbaumer, Harry

    2014-02-01

    In 1917 Einstein initiated modern cosmology by postulating, based on general relativity, a homogenous, static, spatially curved universe. To counteract gravitational contraction he introduced the cosmological constant. In 1922 Alexander Friedman showed that Albert Einstein's fundamental equations also allow dynamical worlds, and in 1927 Georges Lemaître, backed by observational evidence, concluded that our universe was expanding. Einstein impetuously rejected Friedman's as well as Lemaître's findings. However, in 1931 he retracted his former static model in favour of a dynamic solution. This investigation follows Einstein on his hesitating path from a static to the expanding universe. Contrary to an often advocated belief the primary motive for his switch was not observational evidence, but the realisation that his static model was unstable.

  15. Stability of the Einstein static universe in open cosmological models

    International Nuclear Information System (INIS)

    Canonico, Rosangela; Parisi, Luca

    2010-01-01

    The stability properties of the Einstein static solution of general relativity are altered when corrective terms arising from modification of the underlying gravitational theory appear in the cosmological equations. In this paper the existence and stability of static solutions are considered in the framework of two recently proposed quantum gravity models. The previously known analysis of the Einstein static solutions in the semiclassical regime of loop quantum cosmology with modifications to the gravitational sector is extended to open cosmological models where a static neutrally stable solution is found. A similar analysis is also performed in the framework of Horava-Lifshitz gravity under detailed balance and projectability conditions. In the case of open cosmological models the two solutions found can be either unstable or neutrally stable according to the admitted values of the parameters.

  16. Fast static field CIPT mapping of unpatterned MRAM film stacks

    Science.gov (United States)

    Kjaer, Daniel; Hansen, Ole; Hartmann Henrichsen, Henrik; Chenchen, Jacob Wang; Noergaard, Kristian; Folmer Nielsen, Peter; Hjorth Petersen, Dirch

    2015-04-01

    While investigating uniformity of magnetic tunnel junction (MTJ) stacks we find experimentally and analytically that variation in the resistance area product (RA) is more important to monitor as compared to the tunnel magnetoresistance (TMR), which is less sensitive to MTJ variability. The standard Current In-Plane Tunneling (CIPT) method measures both RA and TMR, but the usefulness for uniformity mapping, e.g. for tool optimization, is limited by excessive measurement time. Thus, we develop and demonstrate a fast complementary static magnetic field method focused only on measurement of RA. We compare the static field method to the standard CIPT method and find perfect agreement between the extracted RA values and measurement repeatability while the static field method is several times faster. The static field CIPT method is demonstrated for 200 mm wafer mapping showing radial as well as asymmetrical variations related to the MTJ deposition conditions.

  17. Tools and Workflows for Collaborating on Static Website Projects

    Directory of Open Access Journals (Sweden)

    Kaitlin Newson

    2017-10-01

    Full Text Available Static website generators have seen a significant increase in popularity in recent years, offering many advantages over their dynamic counterparts. While these generators were typically used for blogs, they have grown in usage for other web-based projects, including documentation, conference websites, and image collections. However, because of their technical complexity, these tools can be inaccessible to content creators depending on their level of technical skill and comfort with web development technologies. Drawing from experience with a collaborative static website project, this article will provide an overview of static website generators, review different tools available for managing content, and explore workflows and best practices for collaborating with teams on static website projects.

  18. Interaction mechanisms and biological effects of static magnetic fields

    Energy Technology Data Exchange (ETDEWEB)

    Tenforde, T.S.

    1994-06-01

    Mechanisms through which static magnetic fields interact with living systems are described and illustrated by selected experimental observations. These mechanisms include electrodynamic interactions with moving, ionic charges (blood flow and nerve impulse conduction), magnetomechanical interactions (orientation and translation of molecules structures and magnetic particles), and interactions with electronic spin states in charge transfer reactions (photo-induced electron transfer in photosynthesis). A general summary is also presented of the biological effects of static magnetic fields. There is convincing experimental evidence for magnetoreception mechanisms in several classes of lower organisms, including bacteria and marine organisms. However, in more highly evolved species of animals, there is no evidence that the interactions of static magnetic fields with flux densities up to 2 Tesla (1 Tesla [T] = 10{sup 4} Gauss) produce either behavioral or physiolocical alterations. These results, based on controlled studies with laboratory animals, are consistent with the outcome of recent epidemiological surveys on human populations exposed occupationally to static magnetic fields.

  19. Static delectric behavior of charged fluids near freezing

    International Nuclear Information System (INIS)

    Fasolino, A.; Parrinello, M.; Tosi, M.P.

    1978-01-01

    The wavenumber-dependent, static dielectric function of classical charged fluids near freezing is obtained from structural data based on computer simulation or neutron diffraction, and its behavior is connected with the freezing process. (Auth.)

  20. Toward the Static Detection of Deadlock in Java Software

    National Research Council Canada - National Science Library

    Fadul, Jose E

    2006-01-01

    ... from continuing while each waits for resources to be freed by the continuation of the other. This thesis proposes a flow-insensitive interprocedural static analysis that detects the possibility that a program can deadlock at runtime...

  1. HIRENASD Experimental Data, Static Cp Plots and Data files

    Data.gov (United States)

    National Aeronautics and Space Administration — Tecplot (ascii) and matlab files are posted here for the Static pressure coefficient data sets. To download all of the data in either tecplot format or matlab...

  2. Analysis of punctuality coefficients in the static method of research

    Directory of Open Access Journals (Sweden)

    Janusz WOCH

    2008-01-01

    Full Text Available Complex research of punctuality requires analysis of many coefficients. In the article the analysis and the example of application one of the basic methods of punctuality measurement – the static one – has been presented.

  3. From Flow Logic to static type systems for coordination languages

    DEFF Research Database (Denmark)

    De Nicola, Rocco; Gorla, Daniele; Hansen, Rene Rydhof

    2010-01-01

    Coordination languages are often used to describe open-ended systems. This makes it challenging to develop tools for guaranteeing the security of the coordinated systems and the correctness of their interaction. Successful approaches to this problem have been based on type systems with dynamic...... checks; therefore, the correctness properties cannot be statically enforced. By contrast, static analysis approaches based on Flow Logic usually guarantee properties statically. In this paper, we show how the insights from the Flow Logic approach can be used to construct a type system for statically...... ensuring secure access to tuple spaces and safe process migration for an extension of the language KLAIM. (C) 2009 Elsevier B.V. All rights reserved....

  4. Nuclear level density of 166Er with static deformation

    International Nuclear Information System (INIS)

    Nasrabadi, M.N.

    2006-01-01

    The level densities of 166 Er is calculated using the microscopic theory of interacting fermions and is compared with experimental. It is concluded that the data can be reproduced with level density formalism for nuclei with static deformation

  5. New Sufficient LMI Conditions for Static Output Stabilization

    DEFF Research Database (Denmark)

    Adegas, Fabiano Daher

    2014-01-01

    This paper presents new linear matrix inequality conditions to the static output feedback stabilization problem. Although the conditions are only sufficient, numerical experiments show excellent success rates in finding a stabilizing controller....

  6. The static effectiveness mass of a slinkyTM

    Science.gov (United States)

    Mak, S. Y.

    1987-11-01

    The static elongation of a loaded spring is derived taking into account its own weight and the fact that a finite nonzero force is required to pull the spring apart. A simple experiment is described to verify that the static effective mass is equal to half of the total mass of the spring using a slinky. The experimental result is in good agreement with the theory.

  7. Static Friction Unsung Hero of Everyday Introductory Biomechanics

    Science.gov (United States)

    Beverly, Nancy

    2006-12-01

    The ability of static friction to accelerate systems does not usually get the attention it deserves in introductory physics. Everyday human contexts abound in our grasp of objects to move them, in our being moved as passengers, and in our own locomotion. Student laboratory, classroom and homework activities have been developed which enable students to explore the vital role of static friction in various biomechanical contexts. Examples will be demonstrated.

  8. Static Characteristics of Conical Hydrostatic Journal Bearing Under Micropolar Lubrication

    Science.gov (United States)

    Rana, N. K.; Gautam, S. S.; Verma, S.

    2014-10-01

    A theoretical analysis for static characteristics of a conical hydrostatic journal bearing for a multirecess constant flow valve compensated under micropolar lubrication has been carried out in this work. The numerical solution of the modified Reynolds equation for the conical bearing has been done using Finite Element Method (FEM) using necessary boundary conditions. The various static characteristics have been presented to analyze the performance of bearing at zero speed.

  9. Rapid Moment Magnitude Estimation Using Strong Motion Derived Static Displacements

    OpenAIRE

    Muzli, Muzli; Asch, Guenter; Saul, Joachim; Murjaya, Jaya

    2015-01-01

    The static surface deformation can be recovered from strong motion records. Compared to satellite-based measurements such as GPS or InSAR, the advantage of strong motion records is that they have the potential to provide real-time coseismic static displacements. The use of these valuable data was optimized for the moment magnitude estimation. A centroid grid search method was introduced to calculate the moment magnitude by using1 model. The method to data sets was applied of the 2011...

  10. Static and flicker perimetry in age-related macular degeneration.

    Science.gov (United States)

    Luu, Chi D; Dimitrov, Peter N; Wu, Zhichao; Ayton, Lauren N; Makeyeva, Galina; Aung, Khin-Zaw; Varsamidis, Mary; Robman, Luba; Vingrys, Algis J; Guymer, Robyn H

    2013-05-01

    The relationship between clinical severity of age-related macular degeneration (AMD) and macular function has not been well established. In this study, we investigated the correlation between clinical severity and functional deficits as detected by static and flicker perimetry. This cross-sectional study consisted of 279 AMD subjects and 24 control participants. AMD subjects were allocated into 1 of 10 AMD severity groups depending on the status of the designated study eye and the fellow eye, as assessed by color fundus photographs. Visual acuity, and static and flicker perimetry were tested on one eye during the same session. The geometric means, SDs, and percentage of abnormal eyes of static and flicker sensitivity of each AMD severity group were determined and compared. The pattern of change in sensitivity and percentage of abnormal eyes for static perimetry across all AMD severity groups were similar to flicker perimetry. Eyes with drusen > 125 μm (P[static] = 0.018, P[flicker] = 0.024), drusenoid epithelial detachment (P[static and flicker] flicker] flicker sensitivities compared to normal eyes. Static (β-coefficient -1.59, 95% confidence interval [CI] -4.78-1.60) and flicker (β-coefficient -1.29, 95% CI -4.66-2.08) sensitivities declined at a similar rate in eyes that showed clinical signs of progression. Static and flicker perimetry were affected similarly across the spectrum of AMD severity, and methods appeared to be valid techniques for assessing retinal sensitivity in AMD once drusen > 125 μm are present, but before the development of late AMD.

  11. Dynamic stretching is effective as static stretching at increasing flexibility

    OpenAIRE

    Coons, John M.; Gould, Colleen E.; Kim, Jwa K.; Farley, Richard S.; Caputo, Jennifer L.

    2017-01-01

    This study examined the effect of dynamic and static (standard) stretching on hamstring flexibility. Twenty-five female volleyball players were randomly assigned to dynamic (n = 12) and standard (n = 13) stretching groups. The experimental group trained with repetitive dynamic stretching exercises, while the standard modality group trained with static stretching exercises. The stretching interventions were equivalent in the time at stretch and were performed three days a week for four weeks. ...

  12. Simulations of the Static Friction Due to Adsorbed Molecules

    OpenAIRE

    He, Gang; Robbins, Mark O.

    2001-01-01

    The static friction between crystalline surfaces separated by a molecularly thin layer of adsorbed molecules is calculated using molecular dynamics simulations. These molecules naturally lead to a finite static friction that is consistent with macroscopic friction laws. Crystalline alignment, sliding direction, and the number of adsorbed molecules are not controlled in most experiments and are shown to have little effect on the friction. Temperature, molecular geometry and interaction potenti...

  13. Static Analysis of Android Apps: A Systematic Literature Review

    OpenAIRE

    Li, Li; Bissyande, Tegawendé François D Assise; Papadakis, Mike; Rasthofer, Siegfried; Bartel, Alexandre; Octeau, Damien; Klein, Jacques; Le Traon, Yves

    2017-01-01

    Context: Static analysis exploits techniques that parse program source code or bytecode, often traversing program paths to check some program properties. Static analysis approaches have been proposed for different tasks, including for assessing the security of Android apps, detecting app clones, automating test cases generation, or for uncovering non-functional issues related to performance or energy. The literature thus has proposed a large body of works, each of which attempts to tackle one...

  14. Staging of cutaneous melanoma

    NARCIS (Netherlands)

    P. Mohr (P.); A.M.M. Eggermont (Alexander); A. Hauschild (Axel); A. Buzaid (A.)

    2009-01-01

    textabstractThe American Joint Committee on Cancer (AJCC) staging of cutaneous melanoma is a continuously evolving system. The identification of increasingly more accurate prognostic factors has led to major changes in melanoma staging over the years, and the current system described in this review

  15. Multiaxial pedicle screw designs: static and dynamic mechanical testing.

    Science.gov (United States)

    Stanford, Ralph Edward; Loefler, Andreas Herman; Stanford, Philip Mark; Walsh, William R

    2004-02-15

    Randomized investigation of multiaxial pedicle screw mechanical properties. Measure static yield and ultimate strengths, yield stiffness, and fatigue resistance according to an established model. Compare these measured properties with expected loads in vivo. Multiaxial pedicle screws provide surgical versatility, but the complexity of their design may reduce their strength and fatigue resistance. There is no published data on the mechanical properties of such screws. Screws were assembled according to a vertebrectomy model for destructive mechanical testing. Groups of five assemblies were tested in static tension and compression and subject to three cyclical loads. Modes of failure, yield, and ultimate strength, yield stiffness, and cycles to failure were determined for six designs of screw. Static compression yield loads ranged from 217.1 to 388.0 N and yield stiffness from 23.7 to 38.0 N/mm. Cycles to failure ranged from 42 x 10(3) to 4,719 x 10(3) at 75% of static ultimate load. There were significant differences between designs in all modes of testing. Failure occurred at the multiaxial link in static and cyclical compression. Bending yield strengths just exceeded loads expected in vivo. Multiaxial designs had lower static bending yield strength than fixed screw designs. Five out of six multiaxial screw designs achieved one million cycles at 200 N in compression bending. "Ball-in-cup" multiaxial locking mechanisms were vulnerable to fatigue failure. Smooth surfaces and thicker material appeared to be protective against fatigue failure.

  16. Effects of a static electric field on nonsequential double ionization

    International Nuclear Information System (INIS)

    Li Hongyun; Wang Bingbing; Li Xiaofeng; Fu Panming; Chen Jing; Liu Jie; Jiang Hongbing; Gong Qihuang; Yan Zongchao

    2007-01-01

    Using a three-dimensional semiclassical method, we perform a systematic analysis of the effects of an additional static electric field on nonsequential double ionization (NSDI) of a helium atom in an intense, linearly polarized laser field. It is found that the static electric field influences not only the ionization rate, but also the kinetic energy of the ionized electron returning to the parent ion, in such a way that, if the rate is increased, then the kinetic energy of the first returning electron is decreased, and vice versa. These two effects compete in NSDI. Since the effect of the static electric field on the ionization of the first electron plays a more crucial role in the competition, the symmetric double-peak structure of the He 2+ momentum distribution parallel to the polarization of the laser field is destroyed. Furthermore, the contribution of the trajectories with multiple recollisions to the NSDI is also changed dramatically by the static electric field. As the static electric field increases, the trajectories with two recollisions, which start at the time when the laser and the static electric field are in the same direction, become increasingly important for the NSDI

  17. Modeling of Static Characteristics of Switched Reluctance Motor

    Directory of Open Access Journals (Sweden)

    Ali Asghar Memon

    2013-01-01

    Full Text Available To investigate the running characteristics of a switched reluctance motor, the static characteristics and related input data tables are required. The static characteristics comprise of flux linkage, co-energy and static torque characteristics. The co-energy and static torque are calculated once data of magnetization characteristics is available. The data of co-energy is required for the calculation of static torque characteristics. The simulation model includes the data of static characteristics for prediction of the instantaneous and steady state performance of the motor. In this research a computer based procedure of experiments is carried out for measurement of the magnetization characteristics. For every set of measurements, the removal of eddy current is carefully addressed. The experiments are carried out on an existing 8/6 pole rotary switched reluctance motor. Additionally, the instantaneous phase current, instantaneous torque and flux waveforms are produced by using linear, which is by default and spline data interpolation separately. The information obtained from theses simulation results will help in an improved simulation model for predicting the performance of the machine.

  18. Computed tomography in staging of bladder carcinoma (Prospective study)

    International Nuclear Information System (INIS)

    Lee, Kyung Soo; Choi, Byung Ihn; Han, Man Chung

    1985-01-01

    Staging of carcinoma of the urinary bladder is important for the choice of therapy and also has prognostic implications. Hitherto the staging has been based upon cystoscopy with biopsy, transurethral resection, and palpation with complementary radiographic examinations such as cystography, urography, lymphangiography, ultrasound and angiography. However, with all these methods, the staging of bladder carcinomas still uncertain and inferior to CT. Authors analyzed CT staging of bladder cancers and compared with pathologic staging of laparotomy results. The results are as following: 1. Overall accuracy of CT staging in bladder carcinoma was 72 percent. 2. Overstaging was 20 percent (5/25) and understaging was 8 percent (2/25). 3. All of CT stage B cancers were proven to be stage B, pathologically. 4. In 6 cases of CT static cancers, only one was correct, 3 were overstaged and 2 were understaged. 5. In 7 cases of CT stage D cancers, 5 were correct and 2 were overstaged. 6. CT detected only 2 cases of pelvic lymph node involvement in 4 of pathologically proven lymphadenopathy

  19. 75 FR 80791 - Pure Magnesium From the People's Republic of China: Final Results of the 2008-2009 Antidumping...

    Science.gov (United States)

    2010-12-23

    ... Notice of Final Determination of Sales at Less than Fair Value: Static Random Access Memory... in the investigation); Kompass Food Trading International v. United States, 24 CIT 678, 683-84 (2000...

  20. Multi-static Serial LiDAR for Surveillance and Identification of Marine Life at MHK Installations

    Energy Technology Data Exchange (ETDEWEB)

    Alsenas, Gabriel [Florida Atlantic Univ., Boca Raton, FL (United States); Dalgleish, Fraser [Florida Atlantic Univ., Boca Raton, FL (United States); Ouyang, Bing [Florida Atlantic Univ., Boca Raton, FL (United States)

    2017-06-30

    Final Report for project DE-EE0006787: Multi-static Serial LiDAR for Surveillance and Identification of Marine Life at MHK Installations. This project developed and tested an optical monitoring system prototype that will be suitable for marine and hydrokinetic (MHK) full project lifecycle observation (baseline, commissioning, and decommissioning), with automated real-time classification of marine animals. This system can be deployed to collect pre-installation baseline species observations at a proposed deployment site with minimal post-processing overhead. To satisfy deployed MHK project species of concern (e.g. Endangered Species Act-listed) monitoring requirements, the system provides automated tracking and notification of the presence of managed animals within established perimeters of MHK equipment and provides high resolution imagery of their behavior through a wide range of conditions. During a project’s decommissioning stage, the system can remain installed to provide resource managers with post-installation data. Our technology, known as an Unobtrusive Multi-static Serial LiDAR Imager (UMSLI), is a technology transfer of underwater distributed LiDAR imaging technology that preserves the advantages of traditional optical and acoustic solutions while overcoming associated disadvantages for MHK environmental monitoring applications. This new approach is a purposefully-designed, reconfigurable adaptation of an existing technology that can be easily mounted on or around different classes of MHK equipment. The system uses low average power red (638nm) laser illumination to be invisible and eye-safe to marine animals and is compact and cost effective. The equipment is designed for long term, maintenance-free operations, to inherently generate a sparse primary dataset that only includes detected anomalies (animal presence information), and to allow robust real-time automated animal classification/identification with a low data bandwidth requirement. Advantages

  1. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Held, Isaac [Princeton Univ., NJ (United States); Balaji, V. [Princeton Univ., NJ (United States); Fueglistaler, Stephan [Princeton Univ., NJ (United States)

    2016-09-19

    We have constructed and analyzed a series of idealized models of tropical convection interacting with large-scale circulations, with 25-50km resolution and with 1-2km cloud resolving resolution to set the stage for rigorous tests of convection closure schemes in high resolution global climate models. Much of the focus has been on the climatology of tropical cyclogenesis in rotating systems and the related problem of the spontaneous aggregation of convection in non-rotating systems. The PI (Held) will be delivering the honorary Bjerknes lecture at the Fall 2016 AGU meeting in December on this work. We have also provided new analyses of long-standing issues related to the interaction between convection and the large-scale circulation: Kelvin waves in the upper troposphere and lower stratosphere, water vapor transport into the stratosphere, and upper tropospheric temperature trends. The results of these analyses help to improve our understanding of processes, and provide tests for future high resolution global modeling. Our final goal of testing new convections schemes in next-generation global atmospheric models at GFDL has been left for future work due to the complexity of the idealized model results meant as tests for these models uncovered in this work and to computational resource limitations. 11 papers have been published with support from this grant, 2 are in review, and another major summary paper is in preparation.

  2. On the Sensitivity of Mechanical Properties of Woven-Fabrics to the Draping Process: Static and Dynamic Assessment Through a CAE-Based Approach

    Science.gov (United States)

    Treviso, Alessandra; Farkas, Laszlo; Mundo, Domenico; Tournour, Michel

    2016-08-01

    Manufacturing processes are often considered the final stage of the design. As a matter of fact, it is during the manufacturing that material properties are ultimately determined. This is especially true for composite materials, whose manufacturing processes are often lowly automated and thus subject to the low repeatability of manual operations. Manufacturing simulations tools are becoming available to support the definition of the manufacturing process and assess the manufacturability of composite parts. The present paper proposes a reversed approach to the laminate design process which starts from the manufacturing simulation in order to quantify the impact of the process on the mechanical properties of the as-produced part. An automotive component is chosen and different woven-fabrics structures are considered to determine their sensitivity to the shearing phenomenon. Homogenization of material properties is performed on a local basis, depending on the local geometry modifications undergone by the reinforcement. Stiffness is then predicted through both static and dynamic analysis. In order to prove the effectiveness of the approach, the obtained results are compared to classic laminate modelling.

  3. Static and dynamic flow analysis of PBDEs in plastics from used and end-of-life TVs and computer monitors by life cycle in Korea.

    Science.gov (United States)

    Lee, Seunghun; Jang, Yong-Chul; Kim, Jong-Guk; Park, Jong-Eun; Kang, Young-Yeul; Kim, Woo-Il; Shin, Sun-Kyoung

    2015-02-15

    This study focused on a quantitative substance flow analysis (SFA) of polybrominated diphenyl ethers (PBDEs) in plastics from obsolete TVs and computer monitors that often contain large amounts of the flame retardants. According to the results of the static SFA study, 1.87 tons and 0.28 tons of PBDEs from newly manufactured TVs and computer monitors were introduced into households in 2011 in Korea, respectively. There were approximately 924 tons and 90.3 tons of PBDEs present in TVs and computer monitors in households during product use, respectively. The results of the dynamic SFA study indicated that in 2017 the amount of PBDEs from TVs and computer monitors in the recycling stage is expected to be 2.63 tons and 0.1 tons, respectively. Large fractions of PBDEs from used TVs are present in recycled plastics, while PBDE-containing computer monitors are exported to Southeast Asian countries. This research indicates that PBDEs were emitted the most from recycled plastic pellet processes upon recycling. Further study may be warranted to focus the flow of PBDEs in recycled plastic products in order to determine the final destination and disposal of these chemicals in the environment. Copyright © 2014 Elsevier B.V. All rights reserved.

  4. A planar shock isolation system with high-static-low-dynamic-stiffness characteristic based on cables

    Science.gov (United States)

    Ma, Yanhui; He, Minghua; Shen, Wenhou; Ren, Gexue

    2015-12-01

    In this paper, a simple and designable shock isolation system with ideal high-static-low-dynamic-stiffness (HSLDS) is proposed, which is intended for the horizontal plane shock isolation application. In this system, the isolated object is suspended by several bearing cables and constrained by a number of uniformly distributed pretensioned cables in the horizontal plane, where the low dynamic stiffness of the system is main controlled by the pretension of the planar cables, whilst the high static stiffness is determined by the axial stiffness of the planar cables and their geometric settings. To obtain the HSLDS characteristic of the system, a brief theoretical description of the relationship between the restoring force and displacement is derived. By obtaining the three-order Taylor expansion with sufficient accuracy of the restoring force, influence of planar cable parameters on the low dynamic and high static stiffness is thus given, therefore, the required HSLDS isolator can be easily designed by adjusting the planar cable length, pretension and tensile stiffness. Finally, the isotropy characteristic of the restoring force of the system with different numbers of planar cables is investigated. To evaluate the performance of the system, a rigid isolated object and flexible cables coupling simulation model considering the contacts of the system is established by using multibody dynamics approach. In this model, flexible cables are simulated by 3-node cable element based on the absolute nodal coordinate formulation; the contact between cable and isolated object is simulated based on Hertz contact theory. Finally, the time-domain shock excitation is converted from the design shock spectrum on the basis of BV043/85 criterion. The design procedure of this isolator and some useful guidelines for choosing cable parameters are presented. In addition, a summary about the performance of the isolators with different numbers of cables shocking in an arbitrary direction is

  5. X-ray dynamic observation of cervical degenerative disease induced by unbalanced dynamic and static forces in rats 1.

    Science.gov (United States)

    Xie, Hua; Huang, Yongjing; Nong, Luming; Xu, Nanwei; Gao, Gongming; Zhou, Dong

    2017-09-01

    To investigate dynamically the X-ray appearance of cervical degenerative disease induced by unbalanced dynamic and static forces in rats. A total of 60 Sprague Dawley rats were randomized into test (n=45) and control (n=15) groups, which were randomly subdivided into the one-, three- and six-month post-operative groups. The test group included 10, 15 and 20 rats at the respective corresponding post-operative stage and the control group included five rats at each time-point. By excising cervicodorsal muscles, interspinous ligaments and supraspinous ligament of rats in the test group, the balance of dynamic and static forces on cervical vertebrae was disrupted to establish a rat model of cervical degeneration. Spinal X-ray images were acquired, and intervertebral disc space and intervertebral foramen size were measured at one, three and six months post-operation. The results were analyzed and compared among groups. Cervical dynamic and static imbalance accelerated the appearance of cervical degenerative disease on X-ray. Cervical degenerative disease may be induced by unbalanced dynamic and static forces in rats.

  6. Adaptive-spectral method of monitoring and diagnostic observability of static stresses of elements of mechanical constructions

    Science.gov (United States)

    Sedov, A. V.; Kalinchuk, V. V.; Bocharova, O. V.

    2017-10-01

    The evaluation of static stresses and strength of units and components is a crucial task for increasing reliability in the operation of vehicles and equipment, to prevent emergencies, especially in structures made of metal and composite materials. At the stage of creation and commissioning of structures to control the quality of manufacturing of individual elements and components, diagnostic control methods are widely used. They are acoustic, ultrasonic, X-ray, radiation methods and others. The using of these methods to control the residual life and the degree of static stresses of units and parts during operation is fraught with great difficulties both in methodology and in instrumentation. In this paper, the authors propose an effective method of operative control of the degree of static stresses of units and parts of mechanical structures which are in working condition, based on recording the changing in the surface wave properties of a system consisting of a sensor and a controlled environment (unit, part). The proposed method of low-frequency diagnostics of static stresses presupposes adaptive-spectral decomposition analysis of a surface wave created by external action (impact).

  7. Staging for vulvar cancer.

    Science.gov (United States)

    Hacker, Neville F; Barlow, Ellen L

    2015-08-01

    Vulvar cancer has been staged by the International Federation of Gynaecology and Obstetrics (FIGO) since 1969, and the original staging system was based on clinical findings only. This system provided a very good spread of prognostic groupings. Because vulvar cancer is virtually always treated surgically, the status of the lymph nodes is the most important prognostic factor and this can only be determined with certainty by histological examination of resected lymph nodes, FIGO introduced a surgical staging system in 1988. This was modified in 1994 to include a category of microinvasive vulvar cancer (stage IA), because such patients have virtually no risk of lymph node metastases. This system did not give a reasonably even spread of prognostic groupings. In addition, patients with stage III disease were shown to be a heterogeneous group prognostically, and the number of positive nodes and the morphology of those nodes were not taken into account. A new surgical staging system for vulvar cancer was introduced by FIGO in 2009. Initial retrospective analyses have suggested that this new staging system has overcome the major deficiencies in the 1994 system. Crown Copyright © 2015. Published by Elsevier Ltd. All rights reserved.

  8. Staging for vaginal cancer.

    Science.gov (United States)

    Rajaram, Shalini; Maheshwari, Amita; Srivastava, Astha

    2015-08-01

    Vaginal cancer is a rare cancer comprising about 3% of all gynecologic cancers. Primary vaginal cancer should be carefully assigned as spread from cervix, vulva, and other metastatic tumors to vagina can occur. Although vaginal cancer traditionally occurs in older postmenopausal women, the incidence of high-risk human papillomavirus (HPV)-induced cancers is increasing in younger women. Squamous cell carcinoma is still the most common histopathologic type followed by adenocarcinoma. With decreasing use of diethylstilbestrol in pregnancy, non-diethylstilbestrol-associated cancers are described. The Federation Internationale de Gynecologie et d'Obstetrique (FIGO) staging of vaginal cancer (2009) follows the same rules as cervical cancer; it is clinically staged and allows the use of routine investigative modalities for staging. Although FIGO encourages the use of advanced imaging modalities, such as computed tomography, magnetic resonance imaging (MRI), and positron emission tomography (PET), to guide therapy, the imaging findings may not be used to change or reassign the stage. TNM staging is the pathologic staging system proposed by the American Joint Committee on Cancer, and information available from examination of the resected specimen, including pelvic and inguinal lymph nodes, may be used for staging. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Efficiency of static core turn-off in a system-on-a-chip with variation

    Science.gov (United States)

    Cher, Chen-Yong; Coteus, Paul W; Gara, Alan; Kursun, Eren; Paulsen, David P; Schuelke, Brian A; Sheets, II, John E; Tian, Shurong

    2013-10-29

    A processor-implemented method for improving efficiency of a static core turn-off in a multi-core processor with variation, the method comprising: conducting via a simulation a turn-off analysis of the multi-core processor at the multi-core processor's design stage, wherein the turn-off analysis of the multi-core processor at the multi-core processor's design stage includes a first output corresponding to a first multi-core processor core to turn off; conducting a turn-off analysis of the multi-core processor at the multi-core processor's testing stage, wherein the turn-off analysis of the multi-core processor at the multi-core processor's testing stage includes a second output corresponding to a second multi-core processor core to turn off; comparing the first output and the second output to determine if the first output is referring to the same core to turn off as the second output; outputting a third output corresponding to the first multi-core processor core if the first output and the second output are both referring to the same core to turn off.

  10. The Assessing of the Failure Behavior of Glass/Polyester Composites Subject to Quasi Static Stresses

    Science.gov (United States)

    Stanciu, M. D.; Savin, A.; Teodorescu-Drăghicescu, H.

    2017-06-01

    Using glass fabric reinforced composites for structure of wind turbine blades requires high mechanical strengths especially to cyclic stresses. Studies have shown that approximately 50% of composite material failure occurs because of fatigue. Composites behavior to cyclic stresses involves three stages regarding to stiffness variation: the first stage is characterized by the accelerated decline of stiffness with micro-cracks, the second stage - a slight decrease of stiffness characterized by the occurrence of delamination and third stage characterized by higher decreases of resistance and occurrence of fracture thereof. The aim of the paper is to analyzed the behavior of composites reinforced with glass fibers fabric type RT500 and polyester resin subjected to tensile cyclic loading with pulsating quasi-static regime with asymmetry coefficient R = 0. The samples were tested with the universal tensile machine LS100 Lloyd Instruments Plus, with a load capacity of 100 kN. The load was applied with different speeds of 1 mm/min, 10 mm/min and 20 mm/min. After tests, it was observed that the greatest permanent strains were recorded in the first load cycles when the total energy storage by material was lost due to internal friction. With increasing number of cycles, the glass/polyester composites ability to store energy of deformation decreases, the flow phenomenon characterized by large displacements to smaller loading forces appearing.

  11. How Static Is the Statics Classroom? An Investigation into How Innovations, Specifically Research-Based Instructional Strategies, Are Adopted into the Statics Classroom

    Science.gov (United States)

    Cutler, Stephanie Leigh

    2013-01-01

    The purpose of this dissertation is to investigate how educational research, specifically Research-Based Instructional Strategies (RBIS), is adopted by education practice, specifically within the engineering Statics classroom. Using a systematic approach, changes in classroom teaching practices were investigated from the instructors' perspective.…

  12. Opinion formation models in static and dynamic social networks

    Science.gov (United States)

    Singh, Pramesh

    We study models of opinion formation on static as well as dynamic networks where interaction among individuals is governed by widely accepted social theories. In particular, three models of competing opinions based on distinct interaction mechanisms are studied. A common feature in all of these models is the existence of a tipping point in terms of a model parameter beyond which a rapid consensus is reached. In the first model that we study on a static network, a node adopts a particular state (opinion) if a threshold fraction of its neighbors are already in that state. We introduce a few initiator nodes which are in state '1' in a population where every node is in state '0'. Thus, opinion '1' spreads through the population until no further influence is possible. Size of the spread is greatly affected by how these initiator nodes are selected. We find that there exists a critical fraction of initiators pc that is needed to trigger global cascades for a given threshold phi. We also study heuristic strategies for selecting a set of initiator nodes in order to maximize the cascade size. The structural properties of networks also play an important role in the spreading process. We study how the dynamics is affected by changing the clustering in a network. It turns out that local clustering is helpful in spreading. Next, we studied a model where the network is dynamic and interactions are homophilic. We find that homophily-driven rewiring impedes the reaching of consensus and in the absence of committed nodes (nodes that are not influenceable on their opinion), consensus time Tc diverges exponentially with network size N . As we introduce a fraction of committed nodes, beyond a critical value, the scaling of Tc becomes logarithmic in N. We also find that slight change in the interaction rule can produce strikingly different scaling behaviors of T c . However, introducing committed agents in the system drastically improves the scaling of the consensus time regardless of

  13. The effect of warm-up, static stretching and dynamic stretching on hamstring flexibility in previously injured subjects.

    LENUS (Irish Health Repository)

    O'Sullivan, Kieran

    2009-01-01

    BACKGROUND: Warm-up and stretching are suggested to increase hamstring flexibility and reduce the risk of injury. This study examined the short-term effects of warm-up, static stretching and dynamic stretching on hamstring flexibility in individuals with previous hamstring injury and uninjured controls. METHODS: A randomised crossover study design, over 2 separate days. Hamstring flexibility was assessed using passive knee extension range of motion (PKE ROM). 18 previously injured individuals and 18 uninjured controls participated. On both days, four measurements of PKE ROM were recorded: (1) at baseline; (2) after warm-up; (3) after stretch (static or dynamic) and (4) after a 15-minute rest. Participants carried out both static and dynamic stretches, but on different days. Data were analysed using Anova. RESULTS: Across both groups, there was a significant main effect for time (p < 0.001). PKE ROM significantly increased with warm-up (p < 0.001). From warm-up, PKE ROM further increased with static stretching (p = 0.04) but significantly decreased after dynamic stretching (p = 0.013). The increased flexibility after warm-up and static stretching reduced significantly (p < 0.001) after 15 minutes of rest, but remained significantly greater than at baseline (p < 0.001). Between groups, there was no main effect for group (p = 0.462), with no difference in mean PKE ROM values at any individual stage of the protocol (p > 0.05). Using ANCOVA to adjust for the non-significant (p = 0.141) baseline difference between groups, the previously injured group demonstrated a greater response to warm-up and static stretching, however this was not statistically significant (p = 0.05). CONCLUSION: Warm-up significantly increased hamstring flexibility. Static stretching also increased hamstring flexibility, whereas dynamic did not, in agreement with previous findings on uninjured controls. The effect of warm-up and static stretching on flexibility was greater in those with reduced

  14. Staged bilateral carotid endarterectomy

    DEFF Research Database (Denmark)

    Schroeder, T; Sillesen, H; Engell, Hans Christian

    1986-01-01

    In a series of 56 staged bilateral carotid endarterectomies, new neurologic symptoms developed in 5% and 20% following the first and second procedure, respectively. All complications were transient or minor. The incidence of postendarterectomy hypertension was significantly higher following...... the second procedure, when operations were staged less than 3 weeks apart. A correlation between these hypertensive episodes and the occurrence of new neurologic symptoms could not be shown. However, as this correlation has been proved in several other reports, bilateral carotid endarterectomy is advised...... to be staged at least 3 weeks apart. In addition, a conservative attitude towards contralateral asymptomatic lesions is proposed....

  15. Staging of lung cancer.

    Science.gov (United States)

    de Groot, Patricia M; Carter, Brett W; Betancourt Cuellar, Sonia L; Erasmus, Jeremy J

    2015-06-01

    Primary lung cancer is the leading cause of cancer mortality in the world. Thorough clinical staging of patients with lung cancer is important, because therapeutic options and management are to a considerable degree dependent on stage at presentation. Radiologic imaging is an essential component of clinical staging, including chest radiography in some cases, computed tomography, MRI, and PET. Multiplanar imaging modalities allow assessment of features that are important for surgical, oncologic, and radiation therapy planning, including size of the primary tumor, location and relationship to normal anatomic structures in the thorax, and existence of nodal and/or metastatic disease. Copyright © 2015 Elsevier Inc. All rights reserved.

  16. Staging Mobilities / Designing Mobilities

    DEFF Research Database (Denmark)

    Jensen, Ole B.

    2015-01-01

    In recent years, urban research has taken a ‘mobilities turn’. There has been a developing realisation that mobilities do not ‘just happen.’ Mobilities are carefully and meticulously designed, planned and staged (from above). However, they are equally importantly acted out, performed and lived...... asks: what are the physical, social, technical, and cultural conditions to the staging of contemporary urban mobilities? The theoretical framing in the Staging mobilities book is applied to four in-depth cases in the accompanying volume Designing mobilities.This book explore how places, sites...

  17. EFFECT OF STATIC STRETCHING ON STRENGTH OF HAMSTRING MUSCLE

    Directory of Open Access Journals (Sweden)

    Shweta P Pachpute

    2016-04-01

    Full Text Available Background: Flexibility is an indisputable component of fitness defined as the ability to move a single joint or series of joints through an unrestricted pain free range of motion. Static stretching consists of stretching a muscle or group of muscle to its farthest point and then maintaining or holding that position. The literature supports that muscles are capable of exerting their greatest strength when they are fully lengthen. Hence this study was conducted to find the effect of static stretching on hamstring muscle. Methods: The study was experimental study design. 40 samples were selected by purposive sampling method. Flexibility of the hamstring muscle unilaterally right side (arbitrarily chosen was measured by active knee extension test of all the subjects who met the inclusion criteria of the study. After measuring the flexibility of hamstring muscle, strength was measured by 1RM for the same side (right hamstring muscle. Static Stretching Protocol was given for 5 days per week for 6 weeks to all the participants. After the 6 weeks of training, knee extension deficiency and 1RM was documented. Result: Statistical analysis using Paired t-test was done. The t-test showed that there was significant effect of static stretching on 1RM of hamstring muscle (p<0.05 & active knee extension test (p=0.000. Conclusion: Static stretching showed significant change in pre and post 1RM of hamstring muscle and active knee extension test. There was significant improvement of hamstring muscles flexibility and strength after giving static stretching in female population. So it is possible that females who are unable to participate in traditional strength training activities may be able to experience gains through static stretching.

  18. Static and Dynamic Handgrip Strength Endurance: Test-Retest Reproducibility.

    Science.gov (United States)

    Gerodimos, Vassilis; Karatrantou, Konstantina; Psychou, Dimitra; Vasilopoulou, Theodora; Zafeiridis, Andreas

    2017-03-01

    This study investigated the reliability of static and dynamic handgrip strength endurance using different protocols and indicators for the assessment of strength endurance. Forty young, healthy men and women (age, 18-22 years) performed 2 handgrip strength endurance protocols: a static protocol (sustained submaximal contraction at 50% of maximal voluntary contraction) and a dynamic one (8, 10, and 12 maximal repetitions). The participants executed each protocol twice to assess the test-retest reproducibility. Total work and total time were used as indicators of strength endurance in the static protocol; the strength recorded at each maximal repetition, the percentage change, and fatigue index were used as indicators of strength endurance in the dynamic protocol. The static protocol showed high reliability irrespective of sex and hand for total time and work. The 12-repetition dynamic protocol exhibited moderate-high reliability for repeated maximal repetitions and percentage change; the 8- and 10-repetition protocols demonstrated lower reliability irrespective of sex and hand. The fatigue index was not a reliable indicator for the assessment of dynamic handgrip endurance. Static handgrip endurance can be measured reliably using the total time and total work as indicators of strength endurance. For the evaluation of dynamic handgrip endurance, the 12-repetition protocol is recommended, using the repeated maximal repetitions and percentage change as indicators of strength endurance. Practitioners should consider the static (50% maximal voluntary contraction) and dynamic (12 repeated maximal repetitions) protocols as reliable for the assessment of handgrip strength endurance. The evaluation of static endurance in conjunction with dynamic endurance would provide more complete information about hand function. Copyright © 2017 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

  19. Stages of Colon Cancer

    Science.gov (United States)

    ... types of surgery : Local excision or simple polypectomy . Resection and anastomosis . This is done when the tumor is too ... stage I colon cancer usually includes the following: Resection and anastomosis . Use our clinical trial search to find NCI- ...

  20. Stages of Labor

    Science.gov (United States)

    ... Moms Need Blog News & Media News Videos Mission stories Ambassadors Spotlights Tools & Resources Frequently asked media questions ... can be born. This stage can last as short as 20 minutes or as long as several ...

  1. Multiple Stages 2

    DEFF Research Database (Denmark)

    Andreasen, John

    Multiple stages 2: theatrical futures, set design, community plays, cultural capitals, democracy & drama, WWII dramas, performance on adoption, promenade about emigration, qualities in political theatre, performance analysis, dramaturgical education, Toulmin Variations...

  2. Stages of Esophageal Cancer

    Science.gov (United States)

    ... the body to send radiation toward the cancer. Internal radiation therapy uses a radioactive substance sealed in needles, seeds , ... stage of the cancer being treated. External and internal radiation therapy are used to treat esophageal cancer. A plastic ...

  3. Stages of Anal Cancer

    Science.gov (United States)

    ... the body to send radiation toward the cancer. Internal radiation therapy uses a radioactive substance sealed in needles, seeds , ... stage of the cancer being treated. External and internal radiation therapy are used to treat anal cancer. Chemotherapy Chemotherapy ...

  4. Stages of Penile Cancer

    Science.gov (United States)

    ... the body to send radiation toward the cancer. Internal radiation therapy uses a radioactive substance sealed in needles, seeds , ... stage of the cancer being treated. External and internal radiation therapy are used to treat penile cancer. Chemotherapy Chemotherapy ...

  5. Staging interrail mobilities

    DEFF Research Database (Denmark)

    Jensen, Martin Trandberg; Gyimóthy, Szilvia; Jensen, Ole B.

    2016-01-01

    This article applies the multiscalar ‘staging mobilities’ framework from the emergent subfield of mobilities design to analyse an enduring European rail travel phenomenon, interrail. This discussion extends and contributes to tourism mobilities research. Second, the article enriches previous...

  6. Stages of ores formation

    International Nuclear Information System (INIS)

    Khasanov, A.Kh.

    1988-01-01

    Deposit formation (especially endogenous) is the complicated, multi-stage and long process. Establishment of deposit formation succession, age-specific correlations of minerals and aggregates have a high importance at solving genetic questions. Studying of minerals correlations and mineral aggregates, succession of their crystallization and other observations let restore the history of deposit formation, pick up in it different on duration and physical and chemical conditions stages

  7. Ozone: Stage Two Vapor Recovery Rule and Guidance

    Science.gov (United States)

    This page includes the guidance document, fact sheet, memorandum, and final rule on removing Stage II Gasoline Vapor Control Programs from State Implementation Plans (SIP) for the Ozone National Ambient Air Quality Standards (NAAQS)

  8. Static and dynamic pupillometry data of healthy individuals.

    Science.gov (United States)

    Tekin, Kemal; Sekeroglu, Mehmet Ali; Kiziltoprak, Hasan; Doguizi, Sibel; Inanc, Merve; Yilmazbas, Pelin

    2018-01-21

    This study sought to determine normative static and dynamic pupillometry data in different age groups in a healthy population, and to investigate the effects of age on pupillometric characteristics. Pupillometry measurements were undertaken on 155 healthy participants using an automatic quantitative pupillometry system. Static pupillometry measurements were undertaken; these included scotopic pupil diameter (PD), mesopic PD, low photopic PD and high photopic PD values. Dynamic pupillometry measurements were undertaken, including resting diameter, amplitude of pupil contraction, latency of pupil contraction, duration of pupil contraction, velocity of pupil contraction, latency of pupil dilation, duration of pupil dilation and velocity of pupil dilation. Overall, 69 (44.5 per cent) participants were male and 86 (55.5 per cent) were female, with a mean age of 29.7 ± 17.8 years. Neither static nor dynamic pupillometry measurements varied significantly between males and females. Age was inversely and moderately correlated with each of the static pupillometric characteristics (p static and dynamic pupillometry values in different age groups and the effect of age on pupillary characteristics. © 2018 Optometry Australia.

  9. Enhancement of sedimentation and coagulation with static magnetic field

    Science.gov (United States)

    Zieliński, Marcin; Dębowski, Marcin; Hajduk, Anna; Rusanowska, Paulina

    2017-11-01

    The static magnetic field can be an alternative method for wastewater treatment. It has been proved that this physical factor, accelerates the biochemical processes, catalyzes advanced oxidation, intensifies anaerobic and aerobic processes or reduces swelling of activated sludge. There are also reports proving the positive impact of the static magnetic field on the coagulation and sedimentation, as well as the conditioning and dewatering of sludge. In order to be applied in larger scale the published results should be verified and confirmed. In the studies, the enhancement of sedimentation by the static magnetic field was observed. The best sedimentation was noted in the experiment, where magnetizers were placed on activated sludge bioreactor and secondary settling tank. No effect of the static magnetic field on coagulation with the utilization of PIX 113 was observed. However, the static magnetic field enhanced coagulation with the utilization of PAX-XL9. The results suggest that increased sedimentation of colloids and activated sludge, can in practice mean a reduction in the size of the necessary equipment for sedimentation with an unchanged efficiency of the process.

  10. Static friction between silicon nanowires and elastomeric substrates.

    Science.gov (United States)

    Qin, Qingquan; Zhu, Yong

    2011-09-27

    This paper reports the first direct measurements of static friction force and interfacial shear strength between silicon (Si) nanowires (NWs) and poly(dimethylsiloxane) (PDMS). A micromanipulator is used to manipulate and deform the NWs under a high-magnification optical microscope in real time. The static friction force is measured based on "the most-bent state" of the NWs. The static friction and interface shear strength are found to depend on the ultraviolet/ozone (UVO) treatment of PDMS. The shear strength starts at 0.30 MPa without UVO treatment, increases rapidly up to 10.57 MPa at 60 min of treatment and decreases for longer treatment. Water contact angle measurements suggest that the UVO-induced hydrophobic-to-hydrophilic conversion of PDMS surface is responsible for the increase in the static friction, while the hydrophobic recovery effect contributes to the decrease. The static friction between NWs and PDMS is of critical relevance to many device applications of NWs including NW-based flexible/stretchable electronics, NW assembly and nanocomposites (e.g., supercapacitors). Our results will enable quantitative interface design and control for such applications. © 2011 American Chemical Society

  11. A generic three-dimensional static force distribution basis for a medical needle inserted into soft tissue.

    Science.gov (United States)

    Robert, Adeline L G; Chagnon, Grégory; Bricault, Ivan; Cinquin, Philippe; Moreau-Gaudry, Alexandre

    2013-12-01

    In this paper, the static interaction forces between a medical needle and soft tissue during CT (Computerized Tomography) guided insertion are studied. More precisely a set of linearly independent elements describing the forces (a basis) is identified. This forms a generic basis from which any forces that act on a static needle (that is not fixed at its base and that is inserted into human tissue) can be described accurately. To achieve this purpose, the same needle was inserted 62 times into fresh porcine shoulder tissue and CT scans were acquired after each push to determine the final trajectory of the needle. From this set of trajectories, a generic static force basis was determined by using static Beam, B-spline theories and Principal Component Analysis (PCA). This generic basis was first validated on theoretical simulations and then on 20 different needles inserted into in vivo human tissues during real clinical interventions. Such a basis could be of use to highlight the forces acting all along the length of a needle inserted into a complex tissue and enables models of needle deflection to be developed. These models could be used in the development of automated robot assisted and/or image guided strategies for needle steering. © 2013 Elsevier Ltd. All rights reserved.

  12. Chemotherapy Toxicity On Quality of Life in Older Patients With Stage I, Stage II, Stage III, or Stage IV Ovarian Epithelial, Primary Peritoneal Cavity, or Fallopian Tube Cancer

    Science.gov (United States)

    2017-05-03

    Stage I Ovarian Cancer; Stage IA Fallopian Tube Cancer; Stage IB Fallopian Tube Cancer; Stage IC Fallopian Tube Cancer; Stage II Ovarian Cancer; Stage IIA Fallopian Tube Cancer; Stage IIB Fallopian Tube Cancer; Stage IIC Fallopian Tube Cancer; Stage III Ovarian Cancer; Stage III Primary Peritoneal Cancer; Stage IIIA Fallopian Tube Cancer; Stage IIIB Fallopian Tube Cancer; Stage IIIC Fallopian Tube Cancer; Stage IV Fallopian Tube Cancer; Stage IV Ovarian Cancer; Stage IV Primary Peritoneal Cancer

  13. The influence of non-clinical eating-related psychopathology on the recognition of emotion from static faces and realistic social interactions

    OpenAIRE

    Wallis, D. J.; Ridout, N.; Sharpe, E.

    2018-01-01

    The file attached to this record is the author's final peer reviewed version. The Publisher's final version can be found by following the DOI link Emotion recognition deficits have consistently been reported in clinical and sub-clinical disordered eating. However, most studies have used static faces, despite the dynamic nature of everyday social interactions. The current aims were to confirm previous findings of emotion recognition deficits in non-clinical disordered eating and to determin...

  14. Static trace free Einstein equations and stellar distributions

    Science.gov (United States)

    Hansraj, Sudan; Goswami, Rituparno; Mkhize, Njabulo; Ellis, George

    2017-08-01

    We construct models of static spherical distributions of the perfect fluid in trace free Einstein gravity theory. The equations governing the gravitational field are equivalent to standard Einstein's equations; however, their presentation is manifestly different, which motivates the question whether new information would emerge due to the nonlinearity of the field equations. The incompressible fluid assumption does not lead to the well known Schwarzschild interior metric of Einstein gravity, and a term denoting the presence of a cosmological constant is present on account of the integration process. The Schwarzschild interior is regained as a special case of a richer geometry. On the other hand, when the Schwarzschild geometry is prescribed, a constant density fluid emerges consistent with the standard equations. A complete model of an isothermal fluid sphere with pressure and density obeying the inverse square law is obtained. Corrections to the model previously presented in the literature by Saslaw et al. are exhibited. The isothermal ansatz does not yield a constant gravitational potential in general, but both potentials are position dependent. Conversely, it is shown that assuming a constant gr r gravitational potential does not yield an isothermal fluid in general as is the case in standard general relativity. The results of the standard Einstein equations are special cases of the models reported here. Noteworthy is the fact that whereas the previously reported isothermal solution was only of cosmological interest, the solution reported herein admits compact objects by virtue of the fact that a pressure free hypersurface exists. Finally we analyze the consequences of selecting the Finch-Skea metric as the seed solution. The density profiles match; however, there is a deviation between the pressure profiles with the Einstein case although the qualitative behavior is the same. It is shown in detail that the model satisfies elementary requirements for physical

  15. 14 CFR 29.1325 - Static pressure and pressure altimeter systems.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Static pressure and pressure altimeter...: Installation § 29.1325 Static pressure and pressure altimeter systems. (a) Each instrument with static air case.... (c) Each static pressure port must be designed and located in such manner that the correlation...

  16. Comparative effectiveness of one-stage versus two-stage basilic vein transposition arteriovenous fistulas.

    Science.gov (United States)

    Ghaffarian, Amir A; Griffin, Claire L; Kraiss, Larry W; Sarfati, Mark R; Brooke, Benjamin S

    2018-02-01

    between groups in use of interventions (58% for one-stage BVT vs 51% for two-stage BVT; P = .5) to maintain patency. These findings were confirmed in multivariate analysis, in which two-stage BVTs were associated with a significantly lower rate of failure (hazard ratio, 0.39; 95% confidence interval, 0.2-0.8; P < .05) than one-stage BVTs after controlling for confounding variables. Finally, the two-stage BVT was more cost-effective (3.74 QALYs for two-stage BVT vs 3.32 QALYs for one-stage BVT) during 5 years, with an incremental cost-effectiveness ratio of $4681 per QALY. Our data show that two-stage BVTs are more durable and cost-effective than one-stage procedures, with significantly higher patency and lower rates of failure among comparable risk-stratified patients. These findings suggest that additional upfront costs and resources associated with creating two-stage BVTs are justified by their long-term outcomes. Published by Elsevier Inc.

  17. Relationships between force and muscle oxygenation kinetics during sustained static gripping using a progressive workload.

    Science.gov (United States)

    Demura, Shinichi; Nakada, Masakatsu

    2009-01-01

    This study aimed to examine the relationships between force and subjective muscle-fatigue sensation (SMS), and muscle oxygenation kinetics during sustained static gripping using a progressive workload. Subjects consisted of 10 males (height 173.2+/-7.1 cm, body weight 70.3+/-15.1 kg, and age 21.1+/-1.5 years). They performed sustained static gripping with 7 gradually increasing relative demand values of 20% to 80% maximal voluntary contraction (MVC). The staging of the progressive workload was 10 s for 20% MVC, 20 s each for 30, 40, 50, 60, and 70% MVC, and 10 s for 80% MVC. Borg's SMS was used to measure the fatigue sensation of the antebrachial region in a pre-test and every 10 s during the test. The time to reach minimum Oxy-Hb/Mb appeared at about 50 s (52.6+/-25.2 s) after the onset of sustained static gripping, and the time to reach maximum Deoxy-Hb/Mb occurred later at 90 s. Significant and high correlations (r=0.632-0.721) were found between the time to reach maximum Deoxy-Hb/Mb, and Peak Force Time and Average Force. Even though the demand values caused a workload increase and reached 50% MVC, the change of Total Hb/Mb and Oxy-Hb/Mb kinetics was relatively small. Therefore, the effect caused by an obstruction of blood volume may not occur during the progressive workload. It was determined that the contraction time after the peak of SMS is relatively short and an individual difference in force value expands in the phase where SMS reaches its peak.

  18. Recurrence of particles in static and time varying oval billiards

    Energy Technology Data Exchange (ETDEWEB)

    Leonel, Edson D., E-mail: edleonel@rc.unesp.br [Departamento de Estatística, Matemática Aplicada e Computação – UNESP, Univ Estadual Paulista, Av. 24A, 1515, Bela Vista, 13506-900, Rio Claro, SP (Brazil); Dettmann, Carl P. [School of Mathematics, University of Bristol, Bristol BS8 1TW (United Kingdom)

    2012-04-16

    Dynamical properties are studied for escaping particles, injected through a hole in an oval billiard. The dynamics is considered for both static and periodically moving boundaries. For the static boundary, two different decays for the recurrence time distribution were observed after exponential decay for short times: A changeover to: (i) power law or; (ii) stretched exponential. Both slower decays are due to sticky orbits trapped near KAM islands, with the stretched exponential apparently associated with a single group of large islands. For time dependent case, survival probability leads to the conclusion that sticky orbits are less evident compared with the static case. -- Highlights: ► We consider properties of escaping particles in an oval billiard. ► Two different decays for the recurrence time distribution were observed following an exponential decay for short times: a power law or stretched exponential. ► Time-dependent boundaries suppress the slower decay at later times.

  19. Rigidity of generalized Bach-flat vacuum static spaces

    Science.gov (United States)

    Yun, Gabjin; Hwang, Seungsu

    2017-11-01

    In this paper, we study the structure of generalized Bach-flat vacuum static spaces. Generalized Bach-flat metrics are considered as extensions of both Einstein and Bach-flat metrics. First, we prove that a compact Riemannian n-manifold with n ≥ 4 which is a generalized Bach-flat vacuum static space is Einstein. A generalized Bach-flat vacuum static space with the potential function f having compact level sets is either Ricci-flat or a warped product with zero scalar curvature when n ≥ 5, and when n = 4, it is Einstein if f has its minimum. Secondly, we consider critical metrics for another quadratic curvature functional involving the Ricci tensor, and prove similar results. Lastly, by applying the technique developed above, we prove Besse conjecture when the manifold is generalized Bach-flat.

  20. Reduced arterial diameter during static exercise in humans

    DEFF Research Database (Denmark)

    Olesen, H L; Mitchell, J H; Friedman, D B

    1995-01-01

    for the radial and dorsalis pedis artery was 22 +/- 3 and 28 +/- 3% lower during handgrip than the relation during rest, respectively. After one-leg knee extension both arteries reached 30 +/- 4% lower values. This study demonstrated arterial constriction in the resting limbs within the first 30 s of static......In eight subjects luminal diameter of the resting limb radial and dorsalis pedis arteries was determined by high-resolution ultrasound (20 MHz). This measurement was followed during rest and during 2 min of static handgrip or of one-leg knee extension at 30% of maximal voluntary contraction...... of another limb. Static exercise increased heart rate and mean arterial pressure, which were largest during one-leg knee extension. After exercise heart rate and mean arterial pressure returned to the resting level. No changes were recorded in arterial carbon dioxide tension, and the rate of perceived...

  1. A cumulant functional for static and dynamic correlation

    International Nuclear Information System (INIS)

    Hollett, Joshua W.; Hosseini, Hessam; Menzies, Cameron

    2016-01-01

    A functional for the cumulant energy is introduced. The functional is composed of a pair-correction and static and dynamic correlation energy components. The pair-correction and static correlation energies are functionals of the natural orbitals and the occupancy transferred between near-degenerate orbital pairs, rather than the orbital occupancies themselves. The dynamic correlation energy is a functional of the statically correlated on-top two-electron density. The on-top density functional used in this study is the well-known Colle-Salvetti functional. Using the cc-pVTZ basis set, the functional effectively models the bond dissociation of H 2 , LiH, and N 2 with equilibrium bond lengths and dissociation energies comparable to those provided by multireference second-order perturbation theory. The performance of the cumulant functional is less impressive for HF and F 2 , mainly due to an underestimation of the dynamic correlation energy by the Colle-Salvetti functional.

  2. Determinacy in Static Analysis of jQuery

    DEFF Research Database (Denmark)

    Andreasen, Esben; Møller, Anders

    2014-01-01

    Static analysis for JavaScript can potentially help programmers find errors early during development. Although much progress has been made on analysis techniques, a major obstacle is the prevalence of libraries, in particular jQuery, which apply programming patterns that have detrimental conseque......Static analysis for JavaScript can potentially help programmers find errors early during development. Although much progress has been made on analysis techniques, a major obstacle is the prevalence of libraries, in particular jQuery, which apply programming patterns that have detrimental...... present a static dataflow analysis for JavaScript that infers and exploits determinacy information on-the-fly, to enable analysis of some of the most complex parts of jQuery. The techniques are implemented in the TAJS analysis tool and evaluated on a collection of small programs that use jQuery. Our...

  3. A New Static and Fatigue Compression Test Method for Composites

    DEFF Research Database (Denmark)

    Bech, Jakob Ilsted; Goutianos, Stergios; Løgstrup Andersen, Tom

    2011-01-01

    A new test method to determine the compressive properties of composite materials under both static and fatigue loading was developed. The novel fixture is based on the concept of transmitting the load by a fixed ratio of end-to-shear loading. The end-to-shear load ratio is kept fixed during...... the test through a mechanical mechanism, which automatically maintains the gripping pressure. The combined loading method has proven very efficient in static loading and is used in the new fixture which is specially designed for fatigue testing. Optimum gripping (shear loading) and alignment of the test...... coupon are achieved throughout the fatigue life. The fatigue strength obtained is more reliable because bending of the specimen due to poor gripping and alignment is minimised. The application of the new fixture to static and fatigue compression is demonstrated by using unidirectional carbon...

  4. On perfect fluids and black holes in static equilibrium

    Energy Technology Data Exchange (ETDEWEB)

    Carrasco, Alberto; Mars, Marc; Simon, Walter [Facultad de Ciencias, Universidad de Salamanca, Plaza de la Merced s/n, 37008 Salamanca (Spain)

    2007-05-15

    Proofs of spherical symmetry of static black holes and of spherical symmetry of static perfect fluids normally require, a priori, 'black holes only' or 'fluid only'. In a recent paper Shiromizu, Yamada and Yoshino admit a priori (and exclude) coexistence of fluids and holes. This work assumes connectedness of the fluid region and the same assumptions on the equation of state as earlier papers on the 'fluid only' case, and requires in addition an upper bound for the fluid mass in terms of the black holes masses. We discuss this paper. As a new result we show that there cannot exist static fluid shells (i.e. fluid regions of the topology of an annulus) even if one a priori admits, inside and outside the shell, any arrangement of black holes or additional matter which satisfies the energy condition.

  5. On perfect fluids and black holes in static equilibrium

    International Nuclear Information System (INIS)

    Carrasco, Alberto; Mars, Marc; Simon, Walter

    2007-01-01

    Proofs of spherical symmetry of static black holes and of spherical symmetry of static perfect fluids normally require, a priori, 'black holes only' or 'fluid only'. In a recent paper Shiromizu, Yamada and Yoshino admit a priori (and exclude) coexistence of fluids and holes. This work assumes connectedness of the fluid region and the same assumptions on the equation of state as earlier papers on the 'fluid only' case, and requires in addition an upper bound for the fluid mass in terms of the black holes masses. We discuss this paper. As a new result we show that there cannot exist static fluid shells (i.e. fluid regions of the topology of an annulus) even if one a priori admits, inside and outside the shell, any arrangement of black holes or additional matter which satisfies the energy condition

  6. Vitamins and glucose metabolism: The role of static magnetic fields.

    Science.gov (United States)

    Lahbib, Aïda; Ghodbane, Soumaya; Sakly, Mohsen; Abdelmelek, Hafedh

    2014-12-01

    This review focuses on our own data and other data from the literature of static magnetic fields (SMF) bioeffects and vitamins and glucose metabolism. Three main areas of investigation have been covered: Static magnetic field and glucose metabolism, static magnetic field and vitamins and the role of vitamins on glucose metabolism. Considering these articles comprehensively, the conclusions are as follows: The primary cause of changes in cells after incubation in external SMF is disruption of free radical metabolism and elevation of their concentration. Such disruption causes oxidative stress leading to an unsteadiness of glucose level and insulin release. Moreover, based on available data, it was concluded that exposure to SMF alters plasma levels of vitamin A, C, D and E; these parameters can take part in disorder of glucose homeostasis and insulin release.

  7. Android Application Protection against Static Reverse Engineering based on Multidexing

    Directory of Open Access Journals (Sweden)

    Nak Young Kim

    2016-11-01

    Full Text Available DEX files are executable files of Android applications. Since DEX files are in the format of Java bytecodes, their Java source codes can be easily obtained using static reverse engineering tools. This results in numerous Android application thefts. There are some tools (e.g. bangcle, ijiami, liapp that protect Android applications against static reverse engineering utilizing dynamic code loading. These tools usually encrypt classes.dex in an APK file. When the application is launched, the encrypted classes.dex file is decrypted and dynamically loaded. However, these tools fail to protect multidex APKs, which include more than one DEX files (classes2.dex, classes3.dex, ... to accommodate large-sized execution codes. In this paper, we propose a technique that protects multidex Android applications against static reverse engineering. The technique can encrypt/decrypt multiple DEX files in APK files and dynamically load them. The experimental results show that the proposed technique can effiectively protect multidex APKs.

  8. Biological interactions and human health effects of static magnetic fields

    International Nuclear Information System (INIS)

    Tenforde, T.S.

    1994-09-01

    Mechanisms through which static magnetic fields interact with living systems will be described and illustrated by selected experimental observations. These mechanisms include electrodynamic interactions with moving ionic charges (blood flow and nerve impulse conduction), magnetomechanical interactions (orientation and translation of molecular structures and magnetic particles), and interactions with electronic spin states in charge transfer reactions (photo-induced electron transfer in photosynthesis). A general summary will also be presented of the biological effects of static magnetic fields studied in the laboratory and in natural settings. One aspect of magnetic field effects that merits special concern is their influence on implanted medical electronic devices such as cardiac pacemakers. Several extensive studies have demonstrated closure of the reed switch in pacemakers exposed to relatively weak static magnetic fields, thereby causing them to revert to an asynchronous mode of operation that is potentially hazardous. Recommendations for human exposure limits are provided

  9. From Static to Interactive: Transforming Data Visualization to Improve Transparency.

    Directory of Open Access Journals (Sweden)

    Tracey L Weissgerber

    2016-06-01

    Full Text Available Data presentation for scientific publications in small sample size studies has not changed substantially in decades. It relies on static figures and tables that may not provide sufficient information for critical evaluation, particularly of the results from small sample size studies. Interactive graphics have the potential to transform scientific publications from static reports of experiments into interactive datasets. We designed an interactive line graph that demonstrates how dynamic alternatives to static graphics for small sample size studies allow for additional exploration of empirical datasets. This simple, free, web-based tool (http://statistika.mfub.bg.ac.rs/interactive-graph/ demonstrates the overall concept and may promote widespread use of interactive graphics.

  10. Non-local means filter for trim statics

    KAUST Repository

    Huang, Yunsong

    2014-08-05

    Structures will be mispositioned across prestack migration gathers in the presence of inaccuracies in the velocity model. Stacking these misaligned gathers runs the risk of destroying important structures in the stacked migration image. To mitigate this problem, we propose a trim statics inspired by the non-local means algorithm originally developed for image denoising. This method differs from the conventional one in two fundamental respects. First, the trim statics are computed by comparing image patches instead of individual image traces. Second, no global pilot trace is needed because only two migration images at a time participate in trim statics and are stacked into one image. A multitude of migration images are stacked recursively in this two-to-one fashion. Tests with a Gulf of Mexico dataset show a noticeable improvement in the feature coherency of the stacked migration image.

  11. Evolution of carbon distribution and mechanical properties during the static strain ageing of heavily drawn pearlitic steel wires

    International Nuclear Information System (INIS)

    Lamontagne, A.; Massardier, V.; Sauvage, X.; Kléber, X.; Mari, D.

    2016-01-01

    The static strain ageing of heavily cold-drawn pearlitic steel wires was investigated using both global techniques and local techniques (Atom Probe Tomography (APT)), in order to highlight how the cold-drawn destabilized microstructure returns to a more stable state during post-drawing treatments between 20 °C and 150 °C. The global techniques (thermoelectric power, differential scanning calorimetry) clearly showed that ageing occurs in three successive ageing stages and is due to a redistribution of the carbon atoms coming from the strain-induced cementite dissolution. The first ageing stage was unambiguously attributed to the carbon segregation to the defects, while the second and third stages were interpreted as being due to the precipitation of intermediate carbides (2nd stage) and cementite (3rd stage). The true strain was not found to significantly affect the ageing kinetics and mechanisms but appeared to play a role in the amount of carbon atoms involved in the different ageing stages. APT analyses confirmed that ageing is governed by the carbon depletion of strain-induced supersaturated ferrite. The strengthening mechanisms associated with the different ageing stages were also discussed.

  12. Evolution of carbon distribution and mechanical properties during the static strain ageing of heavily drawn pearlitic steel wires

    Energy Technology Data Exchange (ETDEWEB)

    Lamontagne, A. [Univ Lyon, INSA Lyon, MATEIS – UMR CNRS 5510, Bât. St Exupéry, 25 Avenue Jean Capelle, F-69621 Villeurbanne Cedex (France); Massardier, V., E-mail: veronique.massardier@insa-lyon.fr [Univ Lyon, INSA Lyon, MATEIS – UMR CNRS 5510, Bât. St Exupéry, 25 Avenue Jean Capelle, F-69621 Villeurbanne Cedex (France); Sauvage, X. [University of Rouen, GPM, UMR CNRS 6634, BP 12, Avenue de l’Université, 76801 Saint-Etienne du Rouvray (France); Kléber, X. [Univ Lyon, INSA Lyon, MATEIS – UMR CNRS 5510, Bât. St Exupéry, 25 Avenue Jean Capelle, F-69621 Villeurbanne Cedex (France); Mari, D. [Institute of Condensed Matter Physics, Ecole Polytechnique Fédérale de Lausanne, Station 3, Lausanne CH-1015 (Switzerland)

    2016-06-14

    The static strain ageing of heavily cold-drawn pearlitic steel wires was investigated using both global techniques and local techniques (Atom Probe Tomography (APT)), in order to highlight how the cold-drawn destabilized microstructure returns to a more stable state during post-drawing treatments between 20 °C and 150 °C. The global techniques (thermoelectric power, differential scanning calorimetry) clearly showed that ageing occurs in three successive ageing stages and is due to a redistribution of the carbon atoms coming from the strain-induced cementite dissolution. The first ageing stage was unambiguously attributed to the carbon segregation to the defects, while the second and third stages were interpreted as being due to the precipitation of intermediate carbides (2nd stage) and cementite (3rd stage). The true strain was not found to significantly affect the ageing kinetics and mechanisms but appeared to play a role in the amount of carbon atoms involved in the different ageing stages. APT analyses confirmed that ageing is governed by the carbon depletion of strain-induced supersaturated ferrite. The strengthening mechanisms associated with the different ageing stages were also discussed.

  13. Static or dynamic intramedullary nailing of femur and tibia.

    Science.gov (United States)

    Omerovic, Djemil; Lazovic, Faruk; Hadzimehmedagic, Amel

    2015-04-01

    The basic principle of non-surgical fracture treatment is to restore the original anatomical position of fractured fragments by different techniques, without direct access to the bone and without further traumatizing of tissues. Intramedullary nailing is synthesis and consolidation of fracture fragments with the main goal to gain strength and permanent placement of the implants. Two techniques of intramedullary osteosynthesis are used: with dynamic or with static intramedullary nail. Dynamization include conversion of static nail by removing screws from the longest fragment. The aim of this study is to determine whether there is a difference in the speed and quality of healing of the type A and B fractures of the femur and tibia treated by static or dynamic intramedullary nails and to compare the results. The study was conducted at the Clinic for Orthopaedics and Traumatology, Clinical Center University Sarajevo from January 2004 to June 2009. The study was retrospective-prospective, manipulative, controlled and it was conducted on a total of 129 patients with closed fractures of the diaphysis of the femur and tibia type A and type B, with different segments of bone, regardless of sex and age structure, with the exception of children under 14 years of age. Precisely there were 47 patients with femoral fractures and 82 patients with tibial fractures. The average number of weeks of healing femoral and tibial fractures was slightly in advantage of static intramedullary osteosynthesis, it was 17.08 weeks (SD=3.382). The average number of weeks of healing in 23 patients with fractures of the femur, treated by dynamic intramedullary osteosynthesis was 17.83 (SD=2.978). We can conclude that static intramedullary nailing osteosynthesis unable movements between fragments which directly stimulates bone formation and formation of minimal callus. Static intramedullary osteosynthesis resolve the problem of stabilizing the fracture, limb shortening and rotation of fragments.

  14. Static cerebrovascular pressure autoregulation remains intact during deep hypothermia.

    Science.gov (United States)

    Goswami, Dheeraj; McLeod, Katherine; Leonard, Samantha; Kibler, Kathleen; Easley, Ronald Blaine; Fraser, Charles D; Andropoulos, Dean; Brady, Ken

    2017-09-01

    Clinical studies measuring cerebral blood flow in infants during deep hypothermia have demonstrated diminished cerebrovascular pressure autoregulation. The coexistence of hypotension in these cohorts confounds the conclusion that deep hypothermia impairs cerebrovascular pressure autoregulation. We sought to compare the lower limit of autoregulation and the static rate of autoregulation between normothermic and hypothermic piglets. Twenty anesthetized neonatal piglets (5-7 days old; 10 normothermic and 10 hypothermic to 20°C) had continuous measurements of cortical red cell flux using laser Doppler flowmetry, while hemorrhagic hypotension was induced without cardiopulmonary bypass. Lower limit of autoregulation was determined for each subject using piecewise regression and SRoR was determined above and below each lower limit of autoregulation as (%change cerebrovascular resistance/%change cerebral perfusion pressure). The estimated difference in lower limit of autoregulation was 1.4 mm Hg (lower in the hypothermic piglets; 95% C.I. -10 to 14 mm Hg; P=0.6). The median lower limit of autoregulation in the normothermic group was 39 mm Hg [IQR 38-51] vs 35 mm Hg [31-50] in the hypothermic group. Intact steady-state pressure autoregulation was defined as static rate of autoregulation >0.5 and was demonstrated in all normothermic subjects (static rate of autoregulation=0.72 [0.65-0.87]) and in 9/10 of the hypothermic subjects (static rate of autoregulation=0.65 [0.52-0.87]). This difference in static rate of autoregulation of 0.06 (95% C.I. -0.3 to 0.1) was not significant (P=0.4). Intact steady-state cerebrovascular pressure autoregulation is demonstrated in a swine model of profound hypothermia. Lower limit of autoregulation and static rate of autoregulation were similar in hypothermic and normothermic subjects. © 2017 John Wiley & Sons Ltd.

  15. Staging of extrahepatic cholangiocarcinoma

    Energy Technology Data Exchange (ETDEWEB)

    Chung, Yong Eun; Choi, Jin-Young [Yonsei University College of Medicine, Department of Diagnostic Radiology, Research Institute of Radiological Science, Seoul (Korea); Kim, Myeong-Jin [Yonsei University College of Medicine, Department of Diagnostic Radiology, Research Institute of Radiological Science, Seoul (Korea); Yonsei University College of Medicine, Institute of Gastroenterology, Yonsei (Korea); Yonsei University Health System, Department of Diagnostic Radiology, Seoul (Korea); Park, Young Nyun [Yonsei University College of Medicine, Institute of Gastroenterology, Yonsei (Korea); Yonsei University College of Medicine, Department of Pathology, Yonsei (Korea); Lee, Yoon-Hee [Yonsei University College of Medicine, Department of Pathology, Yonsei (Korea)

    2008-10-15

    Preoperative staging of extrahepatic cholangiocarcinoma is important in determining the best treatment plan. Several classification systems have been suggested to determine the operability and extent of surgery. Longitudinal tumor extent is especially important in extrahepatic cholangiocarcinoma because operative methods differ depending on the tumor extent. The Bismuth-Corlette classification system provides useful information when planning for surgery. However, this classification system is not adequate for selecting surgical candidates. Anatomic variation of the bile duct and gross morphology of the tumor must be considered simultaneously. Lateral spread of the tumor can be evaluated based on the TNM staging provided by American Joint Committee on Cancer (AJCC). However, there is a potential for ambiguity in the distinction of T1 and T2 cancer from one another. In addition, T stage does not necessarily mean invasiveness. Blumgart T staging is helpful for the assessment of resectability with the consideration of nodal status and distant metastasis as suggested by the AJCC cancer staging system. Computed tomography (CT) and magnetic resonance imaging (MRI) are the primary tools used in the assessment of longitudinal and lateral spread of a tumor when determining respectability. Diagnostic laparoscopy and positron emission tomography (PET) may play additional roles in this regard. (orig.)

  16. The Analysis, Optimization, and Simulation of a Two-Stage Tandem Queueing Model with Hyperexponential Service Time at Second Stage

    Directory of Open Access Journals (Sweden)

    Vedat Sağlam

    2015-01-01

    Full Text Available The aim of this paper is to analyze a tandem queueing model with two stages. The arrivals to the first stage are Poisson stream and the service time at this stage is exponential. There is no waiting room at first stage. The service time is hyperexponential and no waiting is allowed at second stage. The transition probabilities and loss probabilities of this model are obtained. In addition, the loss probability at second stage is optimized. Performance measures and the variance of the numbers of customers of this tandem queueing model are found. It is seen that the numbers of customers in first stage and second stage are dependent. Finally we have simulated this queueing model. For different values of parameters, exact values, simulated values, and optimal values of obtained performance measures of this model are numerically shown in tables and graphs.

  17. Effects of Static Stretching and Playing Soccer on Knee Laxity.

    Science.gov (United States)

    Baumgart, Christian; Gokeler, Alli; Donath, Lars; Hoppe, Matthias W; Freiwald, Jürgen

    2015-11-01

    This study investigated exercise-induced effects of static stretching and playing soccer on anterior tibial translation (ATT) of the knee joint. Randomized controlled trial. University biomechanics laboratory. Thirty-one athletes were randomly assigned into a stretching (26.9 ± 6.2 years, 1.77 ± 0.09 m, 67.9 ± 10.7 kg) and a control group (27.9 ± 7.4 years, 1.75 ± 0.08 m, 72.0 ± 14.9 kg). Thirty-one amateur soccer players in an additional soccer group (25.1 ± 5.6 years, 1.74 ± 0.10 m, 71.8 ± 14.8 kg). All participants had no history of knee injury requiring surgery and any previous knee ligament or cartilage injury. The stretching group performed 4 different static stretching exercises with a duration of 2 × 20 seconds interspersed with breaks of 10 seconds. The soccer group completed a 90-minute soccer-specific training program. The control group did not perform any physical activity for approximately 30 minutes. Anterior tibial translation was measured with the KT-1000 knee arthrometer at forces of 67 N, 89 N, and maximal manual force (Max) before and after the intervention. There was a significant increase in ATT after static stretching and playing soccer at all applied forces. Maximal manual testing revealed a mean increase of ATT after static stretching of 2.1 ± 1.6 mm (P static stretching at 67 and 89 N is significantly higher than in controls. At maximum manual testing, significant differences were evident between all groups. Static stretching and playing soccer increase ATT and may consequently influence mechanical factors of the anterior cruciate ligament. The ATT increase after static stretching was greater than after playing soccer. The observed increase in ATT after static stretching and playing soccer may be associated with changes in kinesthetic perception and sensorimotor control, activation of muscles, joint stability, overall performance, and higher injury risk.

  18. Integrating and scheduling an open set of static analyses

    DEFF Research Database (Denmark)

    Eichberg, Michael; Mezini, Mira; Kloppenburg, Sven

    2006-01-01

    To improve the productivity of the development process, more and more tools for static software analysis are tightly integrated into the incremental build process of an IDE. If multiple interdependent analyses are used simultaneously, the coordination between the analyses becomes a major obstacle...... to keep the set of analyses open. We propose an approach to integrating and scheduling an open set of static analyses which decouples the individual analyses and coordinates the analysis executions such that the overall time and space consumption is minimized. The approach has been implemented...

  19. Reachability for Finite-State Process Algebras Using Static Analysis

    DEFF Research Database (Denmark)

    Skrypnyuk, Nataliya; Nielson, Flemming

    2011-01-01

    In this work we present an algorithm for solving the reachability problem in finite systems that are modelled with process algebras. Our method uses Static Analysis, in particular, Data Flow Analysis, of the syntax of a process algebraic system with multi-way synchronisation. The results of the D......In this work we present an algorithm for solving the reachability problem in finite systems that are modelled with process algebras. Our method uses Static Analysis, in particular, Data Flow Analysis, of the syntax of a process algebraic system with multi-way synchronisation. The results...

  20. Fracture characterisation of float glass under static and dynamic loading

    Directory of Open Access Journals (Sweden)

    A. Nyounguè

    2016-12-01

    Full Text Available This paper presents the study of float glass fracture under static and dynamic loading, with the use of experimental and numerical fracture mechanics methods. It has been shown that the value of notch fracture toughness under static loading depends neither on the kind of test nor on specimen geometry. This makes it possible to replace the three-points-bending specimens with the Brazilian discs which are, under certain test conditions, simpler and convenient to study. For both types of specimens, an analysis of the fracture strength, the notch stress intensity factor and fragmentation of specimens was carried out.