WorldWideScience

Sample records for stacked profile plots

  1. Image files of PCR data plotted on the FACS profiles - Plabrain DB | LSDB Archive [Life Science Database Archive metadata

    Lifescience Database Archive (English)

    Full Text Available List Contact us Plabrain DB Image files of PCR data plotted on the FACS profiles Data detail Data name Image files of PCR data plotte...s FACS-based single-cell PCR data was plotted on the FACS profile, in which cells are sorted by DNA content ...d License Update History of This Database Site Policy | Contact Us Image files of PCR data plotted on the FACS profiles - Plabrain DB | LSDB Archive ...

  2. Improved fluid mixing and power density in reverse electrodialysis stacks with chevron-profiled membranes

    NARCIS (Netherlands)

    Pawlowski, Sylwin; Rijnaarts, Timon; Saakes, Michel; Nijmeijer, Kitty; Crespo, João G.; Velizarov, Svetlozar

    2017-01-01

    Spacer-less RED stacks using membranes with integrated spacer profiles have been investigated during the last years to eliminate the spacer shadow effect. The presence of spacers partially blocks the membrane surface and creates a tortuous and thus longer path for ions in the channel, meaning higher

  3. Gain Enhancement of Low-Profile, Electrically Small Capacitive Feed Antennas Using Stacked Meander Lines

    Directory of Open Access Journals (Sweden)

    Kazuki Ide

    2010-01-01

    Full Text Available The present paper describes the gain enhancement of a small and low-profile linear antenna with capacitive feed (C-feed using three metallic layers. The antenna has very small leakage current on the outer conductor of the coaxial cable and can easily control the imaginary part of the input impedance. The gain of the stacked three-layer meander line antenna, with the meander line in the middle layer being opposite to that of the other two layers, has increased by around 7 dB compared to the single layered C-feed antenna. The antenna gain is discussed based on simulated and measured results, which demonstrates that the antenna has successfully achieved the acceptable impedance and sufficient gain for mobile terminals and RFID tags.

  4. The detection of reverse accumulation effect in the positron annihilation profile of stack of aluminum and silver foils

    Directory of Open Access Journals (Sweden)

    Dryzek Jerzy

    2015-12-01

    Full Text Available The implantation profile of positrons emitted from 22Na into a stack of aluminum and silver foils is the subject of the presented report. The characteristic dimple in the profile behind the Ag foil was detected. This effect arises from the differences in the linear absorption coefficient of aluminum and silver. The good agreement between the theoretical profile obtained within the multiscattering model and experimental one was achieved. The observed phenomenon can affect the positron annihilation characteristics measured for the inhomogeneous samples.

  5. Depth Profiling of La2O3 ∕ HfO2 Stacked Dielectrics for Nanoelectronic Device Applications

    KAUST Repository

    Alshareef, Husam N.

    2011-01-03

    Nanoscale La2O3 /HfO2 dielectric stacks have been studied using high resolution Rutherford backscattering spectrometry. The measured distance of the tail-end of the La signal from the dielectric/Si interface suggests that the origin of the threshold voltage shifts and the carrier mobility degradation may not be the same. Up to 20% drop in mobility and 500 mV shift in threshold voltage was observed as the La signal reached the Si substrate. Possible reasons for these changes are proposed, aided by depth profiling and bonding analysis. © 2011 The Electrochemical Society.

  6. Plot 4

    DEFF Research Database (Denmark)

    Lund, Inger-Lise; Hermansen, Anne-Mette; Ferdinand, Trine

    Danskfaglig vejledning informerer om de tanker, der ligger til grund for Plot 4, og beskriver danskfaget ud fra nyere forskning inden for fagets mange delområder. Kapitelvejledning introducerer bogens tekster, forklarer hensigten med kapitlernes opgaver, giver forslag til undervisningen og brugen...

  7. Complexity Plots

    KAUST Repository

    Thiyagalingam, Jeyarajan

    2013-06-01

    In this paper, we present a novel visualization technique for assisting the observation and analysis of algorithmic complexity. In comparison with conventional line graphs, this new technique is not sensitive to the units of measurement, allowing multivariate data series of different physical qualities (e.g., time, space and energy) to be juxtaposed together conveniently and consistently. It supports multivariate visualization as well as uncertainty visualization. It enables users to focus on algorithm categorization by complexity classes, while reducing visual impact caused by constants and algorithmic components that are insignificant to complexity analysis. It provides an effective means for observing the algorithmic complexity of programs with a mixture of algorithms and black-box software through visualization. Through two case studies, we demonstrate the effectiveness of complexity plots in complexity analysis in research, education and application. © 2013 The Author(s) Computer Graphics Forum © 2013 The Eurographics Association and Blackwell Publishing Ltd.

  8. SeqPlots - Interactive software for exploratory data analyses, pattern discovery and visualization in genomics.

    Science.gov (United States)

    Stempor, Przemyslaw; Ahringer, Julie

    2016-01-01

    Experiments involving high-throughput sequencing are widely used for analyses of chromatin function and gene expression. Common examples are the use of chromatin immunoprecipitation for the analysis of chromatin modifications or factor binding, enzymatic digestions for chromatin structure assays, and RNA sequencing to assess gene expression changes after biological perturbations. To investigate the pattern and abundance of coverage signals across regions of interest, data are often visualized as profile plots of average signal or stacked rows of signal in the form of heatmaps. We found that available plotting software was either slow and laborious or difficult to use by investigators with little computational training, which inhibited wide data exploration. To address this need, we developed SeqPlots, a user-friendly exploratory data analysis (EDA) and visualization software for genomics. After choosing groups of signal and feature files and defining plotting parameters, users can generate profile plots of average signal or heatmaps clustered using different algorithms in a matter of seconds through the graphical user interface (GUI) controls. SeqPlots accepts all major genomic file formats as input and can also generate and plot user defined motif densities. Profile plots and heatmaps are highly configurable and batch operations can be used to generate a large number of plots at once. SeqPlots is available as a GUI application for Mac or Windows and Linux, or as an R/Bioconductor package. It can also be deployed on a server for remote and collaborative usage. The analysis features and ease of use of SeqPlots encourages wide data exploration, which should aid the discovery of novel genomic associations.

  9. Algebraic stacks

    Indian Academy of Sciences (India)

    generally, any fiber product) is not uniquely defined: it is only defined up to unique isomorphism. ..... Fiber product. Given two morphisms f1 : F1 ! G, f2 : F2 ! G, we define a new stack. F1 آG F2 (with projections to F1 and F2) as follows. The objects are triples ًX1; X2; ق ..... In fact, any Artin stack F can be defined in this fashion.

  10. Direct evidence of flat band voltage shift for TiN/LaO or ZrO/SiO2stack structure via work function depth profiling.

    Science.gov (United States)

    Heo, Sung; Park, Hyoungsun; Ko, Dong-Su; Kim, Yong Su; Kyoung, Yong Koo; Lee, Hyung-Ik; Cho, Eunae; Lee, Hyo Sug; Park, Gyung-Su; Shin, Jai Kwang; Lee, Dongjin; Lee, Jieun; Jung, Kyoungho; Jeong, Moonyoung; Yamada, Satoru; Kang, Hee Jae; Choi, Byoung-Deog

    2017-03-02

    We demonstrated that a flat band voltage (V FB ) shift could be controlled in TiN/(LaO or ZrO)/SiO 2 stack structures. The V FB shift described in term of metal diffusion into the TiN film and silicate formation in the inserted (LaO or ZrO)/SiO 2 interface layer. The metal doping and silicate formation confirmed by using transmission electron microscopy (TEM) and energy dispersive spectroscopy (EDS) line profiling, respectively. The direct work function measurement technique allowed us to make direct estimate of a variety of flat band voltages (V FB ). As a function of composition ratio of La or Zr to Ti in the region of a TiN/(LaO or ZrO)/SiO 2 /Si stack, direct work function modulation driven by La and Zr doping was confirmed with the work functions obtained from the cutoff value of secondary electron emission by auger electron spectroscopy (AES). We also suggested an analytical method to determine the interface dipole via work function depth profiling.

  11. Observation of dopant-profile independent electron transport in sub-monolayer TiOx stacked ZnO thin films grown by atomic layer deposition

    Science.gov (United States)

    Saha, D.; Misra, P.; Das, Gangadhar; Joshi, M. P.; Kukreja, L. M.

    2016-01-01

    Dopant-profile independent electron transport has been observed through a combined study of temperature dependent electrical resistivity and magnetoresistance measurements on a series of Ti incorporated ZnO thin films with varying degree of static-disorder. These films were grown by atomic layer deposition through in-situ vertical stacking of multiple sub-monolayers of TiOx in ZnO. Upon decreasing ZnO spacer layer thickness, electron transport smoothly evolved from a good metallic to an incipient non-metallic regime due to the intricate interplay of screening of spatial potential fluctuations and strength of static-disorder in the films. Temperature dependent phase-coherence length as extracted from the magnetotransport measurement revealed insignificant role of inter sub-monolayer scattering as an additional channel for electron dephasing, indicating that films were homogeneously disordered three-dimensional electronic systems irrespective of their dopant-profiles. Results of this study are worthy enough for both fundamental physics perspective and efficient applications of multi-stacked ZnO/TiOx structures in the emerging field of transparent oxide electronics.

  12. Algebraic stacks

    Indian Academy of Sciences (India)

    truct the 'moduli stack', that captures all the information that we would like in a fine moduli space. ..... the fine moduli space), it has the property that for any family W of vector bundles (i.e. W is a vector bundle over B ...... the etale topology is finer: V is a 'small enough open subset' because the square root can be defined on it.

  13. Improved NASTRAN plotting

    Science.gov (United States)

    Chan, Gordon C.

    1991-01-01

    The new 1991 COSMIC/NASTRAN version, compatible with the older versions, tries to remove some old constraints and make it easier to extract information from the plot file. It also includes some useful improvements and new enhancements. New features available in the 1991 version are described. They include a new PLT1 tape with simplified ASCII plot commands and short records, combined hidden and shrunk plot, an x-y-z coordinate system on all structural plots, element offset plot, improved character size control, improved FIND and NOFIND logic, a new NASPLOT post-prosessor to perform screen plotting or generate PostScript files, and a BASIC/NASTPLOT program for PC.

  14. Difference and ratio plots

    DEFF Research Database (Denmark)

    Svendsen, Anders Jørgen; Holmskov, U; Bro, Peter

    1995-01-01

    hitherto unnoted differences between controls and patients with either rheumatoid arthritis or systemic lupus erythematosus. For this we use simple, but unconventional, graphic representations of the data, based on difference plots and ratio plots. Differences between patients with Burkitt's lymphoma...... and systemic lupus erythematosus from another previously published study (Macanovic, M. and Lachmann, P.J. (1979) Clin. Exp. Immunol. 38, 274) are also represented using ratio plots. Our observations indicate that analysis by regression analysis may often be misleading....

  15. Plasma physics plotting package

    International Nuclear Information System (INIS)

    Hyman, D.H.

    1981-02-01

    We describe a package of plotting routines that do up to six two- or three-dimensional plots on a frame with minimal loss of resolution. The package now runs on a PDP-10 with PLOT-10 TCS primitives and on a Control Data Corporation-7600 and a Cray-1 with TV80LIB primitives on the National Magnetic Fusion Energy Computer Center network. The package is portable to other graphics systems because only the primitive plot calls are used from the underlying system's graphics package

  16. STILTS Plotting Tools

    Science.gov (United States)

    Taylor, M. B.

    2009-09-01

    The new plotting functionality in version 2.0 of STILTS is described. STILTS is a mature and powerful package for all kinds of table manipulation, and this version adds facilities for generating plots from one or more tables to its existing wide range of non-graphical capabilities. 2- and 3-dimensional scatter plots and 1-dimensional histograms may be generated using highly configurable style parameters. Features include multiple dataset overplotting, variable transparency, 1-, 2- or 3-dimensional symmetric or asymmetric error bars, higher-dimensional visualization using color, and textual point labeling. Vector and bitmapped output formats are supported. The plotting options provide enough flexibility to perform meaningful visualization on datasets from a few points up to tens of millions. Arbitrarily large datasets can be plotted without heavy memory usage.

  17. Two-region mass transfer to account for 2D profile scale heterogeneity in a 1D effective plot scale flow model

    Science.gov (United States)

    Filipovic, Vilim; Coquet, Yves; Gerke, Horst H.

    2017-04-01

    In arable soil landscapes, specific spatial heterogeneities related to tillage and trafficking can influence the movement of water and chemicals. The structure in the topsoil is characterized by spatial patterns with locally compacted zones. The contrasting hydraulic properties of more-and-less compacted soil zones can result in heterogeneous flow fields and preferential flow. Two- or three-dimensional models used to account for soil spatial variability are relatively too complex when trying to include local heterogeneities in the description of field scale flow and transport problems. The idea was to reduce the model complexity linked to the explicit description of heterogeneities in 2D or 3D without deteriorating the validity of simulation results. When reducing the spatial dimensionality, the geometry in a 2D, cross-sectional explicit plot description is removed on the expense of an increased complexity of the 1D model with two flow domains and mass exchange between them. Our objective was to design a simplified 1D model approach that effectively accounts for plot-scale soil structural variability. In this simplified 1D model, effective soil hydraulic parameters can be assigned to each of the two domains separately. Different theoretical scenarios simulating different shape, size and arrangement of compacted clods in the tilled layer were set to estimate their effect on solute behaviour. The mass exchange parameters could be determined from structure quantification and by comparing simplified 1D with reference 2D results accounting for defined soil structural (i.e., here the compacted regions) geometries. The mass exchange is strongly related to the geometry of the compacted zones including their distribution and size within the non-compacted soil. Additionally, the simplified model approach was tested by comparing it with measured results from a field tracer experiment.

  18. Distributed plot-making

    DEFF Research Database (Denmark)

    Jensen, Lotte Groth; Bossen, Claus

    2016-01-01

    different socio-technical systems (paper-based and electronic patient records). Drawing on the theory of distributed cognition and narrative theory, primarily inspired by the work done within health care by Cheryl Mattingly, we propose that the creation of overview may be conceptualised as ‘distributed plot......-making’. Distributed cognition focuses on the role of artefacts, humans and their interaction in information processing, while narrative theory focuses on how humans create narratives through the plot construction. Hence, the concept of distributed plot-making highlights the distribution of information processing...

  19. Density Distribution Sunflower Plots

    Directory of Open Access Journals (Sweden)

    William D. Dupont

    2003-01-01

    Full Text Available Density distribution sunflower plots are used to display high-density bivariate data. They are useful for data where a conventional scatter plot is difficult to read due to overstriking of the plot symbol. The x-y plane is subdivided into a lattice of regular hexagonal bins of width w specified by the user. The user also specifies the values of l, d, and k that affect the plot as follows. Individual observations are plotted when there are less than l observations per bin as in a conventional scatter plot. Each bin with from l to d observations contains a light sunflower. Other bins contain a dark sunflower. In a light sunflower each petal represents one observation. In a dark sunflower, each petal represents k observations. (A dark sunflower with p petals represents between /2-pk k and /2+pk k observations. The user can control the sizes and colors of the sunflowers. By selecting appropriate colors and sizes for the light and dark sunflowers, plots can be obtained that give both the overall sense of the data density distribution as well as the number of data points in any given region. The use of this graphic is illustrated with data from the Framingham Heart Study. A documented Stata program, called sunflower, is available to draw these graphs. It can be downloaded from the Statistical Software Components archive at http://ideas.repec.org/c/boc/bocode/s430201.html . (Journal of Statistical Software 2003; 8 (3: 1-5. Posted at http://www.jstatsoft.org/index.php?vol=8 .

  20. NPLOT - NASTRAN PLOT

    Science.gov (United States)

    Mcentire, K.

    1994-01-01

    NPLOT is an interactive computer graphics program for plotting undeformed and deformed NASTRAN finite element models (FEMs). Although there are many commercial codes already available for plotting FEMs, these have limited use due to their cost, speed, and lack of features to view BAR elements. NPLOT was specifically developed to overcome these limitations. On a vector type graphics device the two best ways to show depth are by hidden line plotting or haloed line plotting. A hidden line algorithm generates views of models with all hidden lines removed, and a haloed line algorithm displays views with aft lines broken in order to show depth while keeping the entire model visible. A haloed line algorithm is especially useful for plotting models composed of many line elements and few surface elements. The most important feature of NPLOT is its ability to create both hidden line and haloed line views accurately and much more quickly than with any other existing hidden or haloed line algorithms. NPLOT is also capable of plotting a normal wire frame view to display all lines of a model. NPLOT is able to aid in viewing all elements, but it has special features not generally available for plotting BAR elements. These features include plotting of TRUE LENGTH and NORMALIZED offset vectors and orientation vectors. Standard display operations such as rotation and perspective are possible, but different view planes such as X-Y, Y-Z, and X-Z may also be selected. Another display option is the Z-axis cut which allows a portion of the fore part of the model to be cut away to reveal details of the inside of the model. A zoom function is available to terminals with a locator (graphics cursor, joystick, etc.). The user interface of NPLOT is designed to make the program quick and easy to use. A combination of menus and commands with help menus for detailed information about each command allows experienced users greater speed and efficiency. Once a plot is on the screen the interface

  1. Thickening the Plot.

    Science.gov (United States)

    Rose, Brian

    1979-01-01

    Examines the content of daytime serial dramas to determine how the narrative structure promotes a sense of involvement in viewers. Competing plot lines, the lack of a concrete sense of resolution, the pattern of episodes, and the audience's awareness of information kept secret from characters all contribute to audience involvement. (JMF)

  2. Air Data - Tile Plot

    Science.gov (United States)

    This tool plots daily AQI values for a specific location and time period. Each square or “tile” represents one day of the year and is color-coded based on the AQI level for that day. The legend tallies the number of days in each AQI category.

  3. Multiple plots in R

    DEFF Research Database (Denmark)

    Edwards, Stefan McKinnon

    2012-01-01

    In this chapter I will investigate how to combine multiple plots into a single. The scenario is a dataset of a series of measurements, on three samples in three situations. There are many ways we can display this, e.g. 3d graphs or faceting. 3d graphs are not good for displaying static data so we...

  4. FLOWPLOT2, 2-D, 3-D Fluid Dynamic Plots

    International Nuclear Information System (INIS)

    Cobb, C.K.; Tunstall, J.N.

    1989-01-01

    1 - Description of program or function: FLOWPLOT2 is a plotting program used with numerical or analytical fluid dynamics codes to create velocity vector plots, contour plots of up to three fluid parameters (e.g. pressure, density, and temperature), two-dimensional profile plots, three-dimensional curve plots, and/or three-dimensional surface plots for either the u or v velocity components. If the fluid dynamics code computes a transient or simulated time related solution, FLOWPLOT2 can also be used to generate these plots for any specified time interval. Multiple cases generating different plots for different time intervals may be run in one execution of the program. In addition, plots can be created for selected two- dimensional planes of three-dimensional steady-state problems. The user has the option of producing plots on CalComp or Versatec plotters or microfiche and of creating a compressed dataset before plotting. 2 - Method of solution: FLOWPLOT2 reads a dataset written by the fluid dynamics code. This dataset must be written in a specified format and must contain parametric data at the nodal points of a uniform or non-uniform rectangular grid formed by the intersection of the grid lines of the model. 3 - Restrictions on the complexity of the problem - Maxima of: 2500 nodes, 40 y-values for 2-D profile plots and 3-D curve plots, 20 contour values, 3 fluid parameters

  5. matplotlib plotting cookbook

    CERN Document Server

    Devert, Alexandre

    2014-01-01

    This book follows a cookbook style approach that puts orthogonal and non-redundant recipes in your hands. Rather than rehashing the user manual, the explanations expose the underlying logic behind Matplotlib. If you are an engineer or scientist who wants to create great visualizations with Python, rather than yet another specialized language, this is the book for you. While there are several very competent plotting packages, Matplotlib is ""just"" a Python module. Thus, if you know some Python already, you will feel at home from the first steps on. In case you are an application writer, you wo

  6. Deploying OpenStack

    CERN Document Server

    Pepple, Ken

    2011-01-01

    OpenStack was created with the audacious goal of being the ubiquitous software choice for building public and private cloud infrastructures. In just over a year, it's become the most talked-about project in open source. This concise book introduces OpenStack's general design and primary software components in detail, and shows you how to start using it to build cloud infrastructures. If you're a developer, technologist, or system administrator familiar with cloud offerings such as Rackspace Cloud or Amazon Web Services, Deploying OpenStack shows you how to obtain and deploy OpenStack softwar

  7. Plotting Gothic: A Paradox

    Directory of Open Access Journals (Sweden)

    Stephen Murray

    2014-06-01

    Full Text Available The paradox of the title is that while most historians of medieval architecture agree that a combination of geometric and arithmetic methods was generally used to lay out a medieval church, there has been little consensus on the specifics of the process in relation to the design of any particular edifice. I begin by identifying four premises which underlie the debate. I then ask whether the new technologies — laser scanning and computer assisted design/drafting applications — can help. A case study uses newly generated point cloud data from a laser scan of the choir of Beauvais Cathedral. Finally, the notion of ‘plotting’ introduces essential sociological, anthropological and rhetorical dimensions. In the spirit of Roland Barthes ('Le plaisir du texte' and Peter Brooks ('Reading for the Plot', we can understand the urgency with which the architectural historian may seek to unscramble the hidden codes of the building as compulsive ‘reading for the plot’.

  8. Spatial variation of PCDD/F and PCB emissions and their composition profiles in stack flue gas from the typical cement plants in China.

    Science.gov (United States)

    Zou, Lili; Ni, Yuwen; Gao, Yuan; Tang, Fengmei; Jin, Jing; Chen, Jiping

    2018-03-01

    Cement production processes are important sources of unintentionally produced persistent organic pollutants (UP-POPs), such as polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), and polychlorinated biphenyls (PCBs). The emissions of PCDD/Fs and PCBs in the stack flue gases from eight typical cement plants in China were investigated in this study, including one wet process rotary kiln, three dry process rotary kilns and four vertical shaft kilns. PCBs exhibited relatively higher mass concentrations with the dioxin-like (dl) and indicator PCBs of 0.14-17.36 and 0.42-12.90 ng/Nm 3 , respectively. However, PCDD/Fs contributed most to the total toxic equivalent concentrations, with the proportions exceeding 90%. The international toxicity equivalency (I-TEQ) concentrations of PCDD/Fs varied greatly from 0.01 to 0.46 ng I-TEQ/Nm 3 in stack gases, two of which exceeded the exhaust gas concentration limit of 0.1 ng I-TEQ/Nm 3 established by the European Union Directive. In weight units, 1,2,3,4,6,7,8-HpCDF was the most abundant congener in the stack gases from various types of cement kilns, with the factions of 17.0-27.8%. TCDFs and PeCDFs were the first two most abundant homologue groups. 2,3,4,7,8-PeCDF was the largest contributor to the total I-TEQ. The emission factors of PCDD/Fs and PCBs in the eight cement kilns were estimated to be 0.01-1.35 μg I-TEQ/t clinker and 8.20 × 10 -4 ∼8.23 × 10 -2  μg World Health Organization TEQ (W-TEQ)/t clinker, respectively. No obvious differences of the PCDD/F and PCB emission factors were found among the varied cement production technologies. Copyright © 2017. Published by Elsevier Ltd.

  9. Stacking transgenic event DAS-Ø15Ø7-1 alters maize composition less than traditional breeding.

    Science.gov (United States)

    Herman, Rod A; Fast, Brandon J; Scherer, Peter N; Brune, Alyssa M; de Cerqueira, Denise T; Schafer, Barry W; Ekmay, Ricardo D; Harrigan, George G; Bradfisch, Greg A

    2017-10-01

    The impact of crossing ('stacking') genetically modified (GM) events on maize-grain biochemical composition was compared with the impact of generating nonGM hybrids. The compositional similarity of seven GM stacks containing event DAS-Ø15Ø7-1, and their matched nonGM near-isogenic hybrids (iso-hybrids) was compared with the compositional similarity of concurrently grown nonGM hybrids and these same iso-hybrids. Scatter plots were used to visualize comparisons among hybrids and a coefficient of identity (per cent of variation explained by line of identity) was calculated to quantify the relationships within analyte profiles. The composition of GM breeding stacks was more similar to the composition of iso-hybrids than was the composition of nonGM hybrids. NonGM breeding more strongly influenced crop composition than did transgenesis or stacking of GM events. These findings call into question the value of uniquely requiring composition studies for GM crops, especially for breeding stacks composed of GM events previously found to be compositionally normal. © 2017 The Authors. Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.

  10. OpenStack essentials

    CERN Document Server

    Radez, Dan

    2015-01-01

    If you need to get started with OpenStack or want to learn more, then this book is your perfect companion. If you're comfortable with the Linux command line, you'll gain confidence in using OpenStack.

  11. Mastering OpenStack

    CERN Document Server

    Khedher, Omar

    2015-01-01

    This book is intended for system administrators, cloud engineers, and system architects who want to deploy a cloud based on OpenStack in a mid- to large-sized IT infrastructure. If you have a fundamental understanding of cloud computing and OpenStack and want to expand your knowledge, then this book is an excellent checkpoint to move forward.

  12. Generalized plotting facility

    Energy Technology Data Exchange (ETDEWEB)

    Burris, R.D.; Gray, W.H.

    1978-01-01

    A command which causes the translation of any supported graphics file format to a format acceptable to any supported device was implemented on two linked DECsystem-10s. The processing of the command is divided into parsing and translating phases. In the parsing phase, information is extracted from the command and augmented by default data. The results of this phase are saved on disk, and the appropriate translating routine is invoked. Twenty-eight translating programs were implemented in this system. They support four different graphics file formats, including the DISSPLA and Calcomp formats, and seven different types of plotters, including Tektronix, Calcomp, and Versatec devices. Some of the plotters are devices linked to the DECsystem-10s, and some are driven by IBM System/360 computers linked via a communications network to the DECsystem-10s. The user of this facility can use any of the supported packages to create a file of graphics data, preview the file on an on-line scope, and, when satisfied, cause the same data to be plotted on a hard-copy device. All of the actions utilize a single simple command format. 2 figures.

  13. A novel design for solid oxide fuel cell stacks

    Energy Technology Data Exchange (ETDEWEB)

    Al-Qattan, A.M.; Chmielewski, D.J.; Al-Hallaj, S.; Selman, J.R. [Illinois Inst. of Technology, Chicago, IL (United States). Dept. of Chemical and Environmental Engineering

    2004-01-01

    Conventional fuel cell stack designs suffer from severe spatial nonuniformity in both temperature and current density. Such variations are known to create damaging thermal stresses within the stack and thus, impact overall lifespan. In this work, we propose a novel stack design aimed at reducing spatial variations at the source. We propose a mechanism of distributed fuel feed in which the heat generation profile can be influenced directly. Simulation results are presented to illustrate the potential of the proposed scheme. (author)

  14. Line structures in recurrence plots

    International Nuclear Information System (INIS)

    Marwan, Norbert; Kurths, Juergen

    2005-01-01

    Recurrence plots exhibit line structures which represent typical behaviour of the investigated system. The local slope of these line structures is connected with a specific transformation of the time scales of different segments of the phase-space trajectory. This provides us a better understanding of the structures occurring in recurrence plots. The relationship between the time-scales and line structures are of practical importance in cross recurrence plots. Using this relationship within cross recurrence plots, the time-scales of differently sampled or time-transformed measurements can be adjusted. An application to geophysical measurements illustrates the capability of this method for the adjustment of time-scales in different measurements

  15. General purpose film plotting system

    Science.gov (United States)

    Mcquillan, C.

    1977-01-01

    The general purpose film plotting system which is a plot program design to handle a majority of the data tape formats presently available under OS/360 was discussed. The convenience of this program is due to the fact that the user merely describes the format of his data set and the type of data plots he desires. It processes the input data according to the given specifications. The output is generated on a tape which yields data plots when processed by the selected plotter. A summary of each job is produced on the printer.

  16. Generalized Probability-Probability Plots

    NARCIS (Netherlands)

    Mushkudiani, N.A.; Einmahl, J.H.J.

    2004-01-01

    We introduce generalized Probability-Probability (P-P) plots in order to study the one-sample goodness-of-fit problem and the two-sample problem, for real valued data.These plots, that are constructed by indexing with the class of closed intervals, globally preserve the properties of classical P-P

  17. Mapped Plot Patch Size Estimates

    Science.gov (United States)

    Paul C. Van Deusen

    2005-01-01

    This paper demonstrates that the mapped plot design is relatively easy to analyze and describes existing formulas for mean and variance estimators. New methods are developed for using mapped plots to estimate average patch size of condition classes. The patch size estimators require assumptions about the shape of the condition class, limiting their utility. They may...

  18. Using Zoom Technologies to Display HEP Plots and Talks

    Science.gov (United States)

    Watts, G.

    2012-12-01

    Particle physics conferences and experiments generate a huge number of plots and presentations. It is impossible to keep up. A typical conference (like CHEP) will have 100's of plots. A single analysis result from a major experiment will have almost 50 plots. Scanning a conference or sorting out what plots are new is almost a full time job. The advent of multi-core computing and advanced video cards means that we have more processor power available for visualization than any time in the past. This poster describes two related projects that take advantage of this to solve the viewing problem. The first, Collider Plots, has a backend that looks for new plots released by ATLAS, CMS, CDF, and DZERO and organizes them by date, by experiment, and by subgroup for easy viewing and sorting. It maintains links back to associated conference notes and web pages with full result information. The second project, Deep Conference, renders all the slides as a single large zoomable picture. In both cases, much like a web mapping program, details are revealed as you zoom in. In the case of Collider Plots the plots are stacked as histograms to give visual clues for the most recent updates and activity have occurred. Standard plug-in software for a browser allows a user to zoom in on a portion of the conference that looks interesting. As the user zooms further more and more details become visible, allowing the user to make a quick and cheap decision on whether to spend more time on a particular talk or series of plots. Both projects are available at http://deeptalk.phys.washington.edu. The poster discusses the implementation and use as well as cross platform performance and possible future directions.

  19. Stack filter classifiers

    Energy Technology Data Exchange (ETDEWEB)

    Porter, Reid B [Los Alamos National Laboratory; Hush, Don [Los Alamos National Laboratory

    2009-01-01

    Just as linear models generalize the sample mean and weighted average, weighted order statistic models generalize the sample median and weighted median. This analogy can be continued informally to generalized additive modeels in the case of the mean, and Stack Filters in the case of the median. Both of these model classes have been extensively studied for signal and image processing but it is surprising to find that for pattern classification, their treatment has been significantly one sided. Generalized additive models are now a major tool in pattern classification and many different learning algorithms have been developed to fit model parameters to finite data. However Stack Filters remain largely confined to signal and image processing and learning algorithms for classification are yet to be seen. This paper is a step towards Stack Filter Classifiers and it shows that the approach is interesting from both a theoretical and a practical perspective.

  20. On Stack Reconstruction Problem

    Directory of Open Access Journals (Sweden)

    V. D. Аkeliev

    2009-01-01

    Full Text Available The paper describes analytical investigations that study relation of fuel combustion regimes with concentration values of sulphur anhydride in flue gases and acid dew point. Coefficients of convective heat transfer at internal and external surfaces of stacks have been determined in the paper. The paper reveals the possibility to reconstruct stacks while using gas discharging channel made of composite material on the basis of glass-reinforced plastic which permits to reduce thermo-stressed actions on reinforced concrete and increase volume of released gases due to practically two-fold reduction of gas-dynamic pressure losses along the pipe length.

  1. Laser pulse stacking method

    Science.gov (United States)

    Moses, E.I.

    1992-12-01

    A laser pulse stacking method is disclosed. A problem with the prior art has been the generation of a series of laser beam pulses where the outer and inner regions of the beams are generated so as to form radially non-synchronous pulses. Such pulses thus have a non-uniform cross-sectional area with respect to the outer and inner edges of the pulses. The present invention provides a solution by combining the temporally non-uniform pulses in a stacking effect to thus provide a more uniform temporal synchronism over the beam diameter. 2 figs.

  2. Plotting Orbital Trajectories For Maneuvers

    Science.gov (United States)

    Brody, Adam R.

    1991-01-01

    Interactive Orbital Trajectory Planning Tool (EIVAN) computer program is forward-looking interactive orbit-trajectory-plotting software tool for use with proximity operations (operations occurring within 1-km sphere of space station) and other maneuvers. Developed to plot resulting trajectories, to provide better comprehension of effects of orbital mechanics, and to help user develop heuristics for planning missions on orbit. Program runs with Microsoft's Excel for execution on MacIntosh computer running MacIntosh OS.

  3. Normal probability plots with confidence.

    Science.gov (United States)

    Chantarangsi, Wanpen; Liu, Wei; Bretz, Frank; Kiatsupaibul, Seksan; Hayter, Anthony J; Wan, Fang

    2015-01-01

    Normal probability plots are widely used as a statistical tool for assessing whether an observed simple random sample is drawn from a normally distributed population. The users, however, have to judge subjectively, if no objective rule is provided, whether the plotted points fall close to a straight line. In this paper, we focus on how a normal probability plot can be augmented by intervals for all the points so that, if the population distribution is normal, then all the points should fall into the corresponding intervals simultaneously with probability 1-α. These simultaneous 1-α probability intervals provide therefore an objective mean to judge whether the plotted points fall close to the straight line: the plotted points fall close to the straight line if and only if all the points fall into the corresponding intervals. The powers of several normal probability plot based (graphical) tests and the most popular nongraphical Anderson-Darling and Shapiro-Wilk tests are compared by simulation. Based on this comparison, recommendations are given in Section 3 on which graphical tests should be used in what circumstances. An example is provided to illustrate the methods. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  4. po_stack_movie

    DEFF Research Database (Denmark)

    2009-01-01

    po_stack® er et reolsystem, hvis enkle elementer giver stor flexibilitet, variation og skulpturel virkning. Elementerne stables og forskydes frit, så reolens rum kan vendes til begge sider, være åbne eller lukkede og farvekombineres ubegrænset. Reolen kan let ombygges, udvides eller opdeles, når ...

  5. Learning SaltStack

    CERN Document Server

    Myers, Colton

    2015-01-01

    If you are a system administrator who manages multiple servers, then you know how difficult it is to keep your infrastructure in line. If you've been searching for an easier way, this book is for you. No prior experience with SaltStack is required.

  6. Trellis plots as visual aids for analyzing split plot experiments

    DEFF Research Database (Denmark)

    Kulahci, Murat; Menon, Anil

    2017-01-01

    The analysis of split plot experiments can be challenging due to a complicated error structure resulting from restrictions on complete randomization. Similarly, standard visualization methods do not provide the insight practitioners desire to understand the data, think of explanations, generate h...

  7. Energy Expenditure of Sport Stacking

    Science.gov (United States)

    Murray, Steven R.; Udermann, Brian E.; Reineke, David M.; Battista, Rebecca A.

    2009-01-01

    Sport stacking is an activity taught in many physical education programs. The activity, although very popular, has been studied minimally, and the energy expenditure for sport stacking is unknown. Therefore, the purposes of this study were to determine the energy expenditure of sport stacking in elementary school children and to compare that value…

  8. OpenStack cloud security

    CERN Document Server

    Locati, Fabio Alessandro

    2015-01-01

    If you are an OpenStack administrator or developer, or wish to build solutions to protect your OpenStack environment, then this book is for you. Experience of Linux administration and familiarity with different OpenStack components is assumed.

  9. PLOT-3D/BARC, Interactive 3-D Colour Plotting

    International Nuclear Information System (INIS)

    Balhans Jayaswal

    1989-01-01

    1 - Description of program or function: PLOT3D is a general purpose, interactive program, designed to draw three dimensional graphs, histograms, maps and stereo 3D plots, in single or multicolour, from arrays of points (x,y,z) under various options such as clipping, smoothening, shading, etc. using a built-in 3D interpolation function, and after arbitrary rotations about the three coordinate axes. 2 - Method of solution: For plotting a two variables dependent function, z(x,y) the program reads its z values in form of a matrix, z(i,j), in which the indices i and j specify the values of x and y, respectively, either by direct proportionality or through array variables, X(i) and Y(j). Thereafter, the program normalizes the data coordinates, transforms them to effect the orientation of the figure, and then draws axonometric projection using single floating horizon method for hidden lines elimination. In addition, a built-in 3D interpolation function allows numerous intermediate points to be generated and immediately plotted and thus helps in drawing 3D histograms or smoothening the plotted surface, and in shading. The program has two modes of hidden lines removal, both based on single floating horizon method. There exist five versions of this program as listed in item 7. 3 - Restrictions on the complexity of the problem: The size of z data matrix cannot exceed 115 x 115. The number of interpolations cannot exceed 1001 x 1001. In versions 4 and 5, the number of colours cannot exceed 16. In layout diagrams, the items cannot be anything but orthorhombic in shape

  10. SUPERIMPOSED MESH PLOTTING IN MCNP

    Energy Technology Data Exchange (ETDEWEB)

    J. HENDRICKS

    2001-02-01

    The capability to plot superimposed meshes has been added to MCNP{trademark}. MCNP4C featured a superimposed mesh weight window generator which enabled users to set up geometries without having to subdivide geometric cells for variance reduction. The variance reduction was performed with weight windows on a rectangular or cylindrical mesh superimposed over the physical geometry. Experience with the new capability was favorable but also indicated that a number of enhancements would be very beneficial, particularly a means of visualizing the mesh and its values. The mathematics for plotting the mesh and its values is described here along with a description of other upgrades.

  11. Surface stabilization and revegetation test plots

    International Nuclear Information System (INIS)

    Sackschewsky, M.R.; Kemp, C.J.; Hayward, W.M.

    1993-09-01

    Westinghouse Hanford Company Decommissioning and Decontamination Engineering Group and Environmental Technology and Assessment Groups are developing new technologies to improve revegetation techniques for interim stabilization control over underground waste sites within the Radiation Area Remedial Action Program. Successful revegetation is an integral aspect of waste isolation strategy. Unfortunately, revegetation can be very difficult to achieve on the Hanford Site due to several factors: low annual precipitation, unpredictable timing of precipitation, low fertility of available soils, and coarse physical texture of soils covering waste sites. The tests in this report were performed during fiscal years 1992 and 1993 and include the use of two soil sealants in combination with bare soil and a soil/compost mixture and a comparison of a wheatgrass mixture and a native seed mixture. Hydroprobe access ports were placed in one-half of the test plots and moisture data was collected. Soil fertility and plant community characteristics were monitored during the two years of the test. During the first year all sites with compost provided additional fertility and retained greater amounts of soil moisture than noncomposted sites. The use of Enduraseal soil fixative provided greater soil moisture than the use of Aerospray-77 soil fixative. During the second year the use of compost and soil fixative's had a lesser effect on soil moisture. During late summer periods all treatments had very similar soil moisture profiles. The use of compost greatly increased vegetative cover and soil fertility in comparison to sites that had no compost added. Testing of the seed mixtures found that Siberian wheatgrass and Sandberg's bluegrass were the most dominant of the seeded species observed. All plots exhibited a dominant plant cover of volunteer cheatgrass. Biomass production was significantly greater on plots with compost than on the noncomposted plots

  12. The use of pattern decomposition to study the combined X-ray diffraction effects of crystallite size and stacking faults in ex-oxalate zinc oxide

    International Nuclear Information System (INIS)

    Langford, J.I.; Boultif, A.; Auffredic, J.P.; Louer, D.

    1993-01-01

    The microstructure of ZnO powder, obtained from thermal decomposition of the oxalate and studied previously by electron microscopy and adsorption calorimetry, was investigated by means of X-ray powder diffraction pattern decomposition. A Williamson-Hall plot revealed that some lines were broadened solely due to the effects of crystallite size, whereas other breadths included a contribution due to stacking faults. Spherical and cylindrical models are used to describe the form of the crystallites and procedures are presented for separating 'size' effects from 'mistake' broadening. This leads to estimates of the mean dimensions of the crystallites and the stacking-fault probability. The analysis demonstrates that, with good-quality data for a large number of reflections, a considerable amount of detailed information can be obtained about microstructure. On the other hand, it reveals some of the limitations of current procedures for modelling diffraction line profiles. (orig.)

  13. Stack Caching Using Split Data Caches

    DEFF Research Database (Denmark)

    Nielsen, Carsten; Schoeberl, Martin

    2015-01-01

    In most embedded and general purpose architectures, stack data and non-stack data is cached together, meaning that writing to or loading from the stack may expel non-stack data from the data cache. Manipulation of the stack has a different memory access pattern than that of non-stack data, showing...... higher temporal and spatial locality. We propose caching stack and non-stack data separately and develop four different stack caches that allow this separation without requiring compiler support. These are the simple, window, and prefilling with and without tag stack caches. The performance of the stack...

  14. When is stacking confusing? The impact of confusion on stacking in deep H I galaxy surveys

    Science.gov (United States)

    Jones, Michael G.; Haynes, Martha P.; Giovanelli, Riccardo; Papastergis, Emmanouil

    2016-01-01

    We present an analytic model to predict the H I mass contributed by confused sources to a stacked spectrum in a generic H I survey. Based on the ALFALFA (Arecibo Legacy Fast ALFA) correlation function, this model is in agreement with the estimates of confusion present in stacked Parkes telescope data, and was used to predict how confusion will limit stacking in the deepest Square Kilometre Array precursor H I surveys. Stacking with LADUMA (Looking At the Distant Universe with MeerKAT) and DINGO UDEEP (Deep Investigation of Neutral Gas Origins - Ultra Deep) data will only be mildly impacted by confusion if their target synthesized beam size of 10 arcsec can be achieved. Any beam size significantly above this will result in stacks that contain a mass in confused sources that is comparable to (or greater than) that which is detectable via stacking, at all redshifts. CHILES (COSMOS H I Large Extragalactic Survey) 5 arcsec resolution is more than adequate to prevent confusion influencing stacking of its data, throughout its bandpass range. FAST (Five hundred metre Aperture Spherical Telescope) will be the most impeded by confusion, with H I surveys likely becoming heavily confused much beyond z = 0.1. The largest uncertainties in our model are the redshift evolution of the H I density of the Universe and the H I correlation function. However, we argue that the two idealized cases we adopt should bracket the true evolution, and the qualitative conclusions are unchanged regardless of the model choice. The profile shape of the signal due to confusion (in the absence of any detection) was also modelled, revealing that it can take the form of a double Gaussian with a narrow and wide component.

  15. Passive stack ventilation

    Energy Technology Data Exchange (ETDEWEB)

    Palmer, J.; Parkins, L.; Shaw, P.; Watkins, R. [Databuild, Birmingham (United Kingdom)

    1994-12-31

    The adequate ventilation of houses is essential for both the occupants and the building fabric. As air-tightness standards increase, background infiltration levels decrease and extra ventilation has to be designed into the building. Passive stack ventilation has many advantages - particularly when employed in low cost housing schemes -but it is essential that it performs satisfactorily. This paper give the results from monitoring two passive stack ventilation schemes. One scheme was a retrofit into refurbished local authority houses in which a package of energy efficiency measures had been taken and condensation had been a problem. The other series of tests were conducted on a new installation in a Housing Association development. Nine houses were monitored each of which had at least two passive vents. The results show air flow rates by the passive ducts equivalent to approximately 1 room air change per hour. The air flow in the ducts was influenced by both, internal to external temperature difference and wind speed and direction. (author)

  16. Asymmetric Flexible Supercapacitor Stack

    Directory of Open Access Journals (Sweden)

    Leela Mohana Reddy A

    2008-01-01

    Full Text Available AbstractElectrical double layer supercapacitor is very significant in the field of electrical energy storage which can be the solution for the current revolution in the electronic devices like mobile phones, camera flashes which needs flexible and miniaturized energy storage device with all non-aqueous components. The multiwalled carbon nanotubes (MWNTs have been synthesized by catalytic chemical vapor deposition technique over hydrogen decrepitated Mischmetal (Mm based AB3alloy hydride. The polymer dispersed MWNTs have been obtained by insitu polymerization and the metal oxide/MWNTs were synthesized by sol-gel method. Morphological characterizations of polymer dispersed MWNTs have been carried out using scanning electron microscopy (SEM, transmission electron microscopy (TEM and HRTEM. An assymetric double supercapacitor stack has been fabricated using polymer/MWNTs and metal oxide/MWNTs coated over flexible carbon fabric as electrodes and nafion®membrane as a solid electrolyte. Electrochemical performance of the supercapacitor stack has been investigated using cyclic voltammetry, galvanostatic charge-discharge, and electrochemical impedance spectroscopy.

  17. Instant BlueStacks

    CERN Document Server

    Judge, Gary

    2013-01-01

    Get to grips with a new technology, understand what it is and what it can do for you, and then get to work with the most important features and tasks. A fast-paced, example-based approach guide for learning BlueStacks.This book is for anyone with a Mac or PC who wants to run Android apps on their computer. Whether you want to play games that are freely available for Android but not your computer, or you want to try apps before you install them on a physical device or use it as a development tool, this book will show you how. No previous experience is needed as this is written in plain English

  18. Nuclear Zpif-type plots

    International Nuclear Information System (INIS)

    Ma Yugang

    2000-01-01

    Isospin dependent classical molecular dynamics model is used to investigate the nuclear disassembly of 129 Xe. Zpif-type plot in the field of linguistics is tested for the rank-classified cluster arrangement from this nuclear disassembly. It is found that the average cluster charge (or mass) of rank n in the charge (or mass) list is exactly inverse to its rank, i.e. there exists Zpif's law at the point of the liquid gas phase transition. This novel criterion can be used to diagnose the nuclear liquid gas phase transition experimentally and theoretically

  19. ABCASH plotting program users guide

    International Nuclear Information System (INIS)

    Troyer, G.L.

    1995-01-01

    The Automated Bar Coding of Air Samples at Hanford (ABCASH) system provides an integrated data collection, sample tracking, and data reporting system for radioactive particulate air filter samples. The ABCASH plotting program provides a graphical trend report for ABCASH of the performance of air sample results. This document provides an operational guide for using the program. Based on sample location identifier and date range, a trend chart of the available data is generated. The trend chart shows radiological activity versus time. General indications of directional trend of the concentrations in air over time may be discerned. Comparison limit set point values are also shown as derived from the ABCASH data base

  20. Sacrifice as a plot device

    Directory of Open Access Journals (Sweden)

    Ashikhmanova Natalya Alexandrovna

    2015-12-01

    Full Text Available It is considered the plot device “sacrifice” as a meaningful component of the narrative. It sets a minimum of substantive meaning of this formation (the idea of getting something over the loss of something. The main types of sacrifice: sacrifice and self-sacrifice. Sacrifice means bringing something to sacrifice for the sake of an idea or someone else and implies a greater degree of external attributes. Self-sacrifice brings a loss of the intrinsic value of the character. Sacrifice as the action takes place consciously and, as a rule, does not require compensation in return. Victims sacrifice not only material things but spiritual as well. Their actions are certainly driven by the idea, which is of value. In the case of self-sacrifice victim is itself a victim. Present for sacrifice plays a certain role in the development of some of the stories of fabulous narratives. Search of the present can be a starting point in the development of fantastic narrative plot. As a sacrifice the present can be considered in three forms: in the form of material expression, in the form of immaterial substance, as well as a way to transfer the character into magical power through knowledge empowerment of its formulaic spells.

  1. AUTOMATED TECHNIQUE FOR CREATING LITHOLOGIC LOG PLOTS

    Directory of Open Access Journals (Sweden)

    Kristijan Posavec

    2006-12-01

    Full Text Available Paper presents automated technique for creating lithologic log plots. Technique is based on three computer tools: Microsoft (MS Access program, LogPlot program, and Visual Basic (VB macros for MS Excel. MS Access ensures professional storage of lithologic data which can be in that way easier and faster entered, searched, updated, and also used for different purposes, while LogPlot provides tools for creating lithologic log plots. VB macros enable transfer of lithologic data from MS Access to LogPlot. Data stored in MS Access are exported in ASCII files which are later used by LogPlot for creation of lithologic log plots. Presented concept facilitates creation of lithologic log plots, and automated technique enables processing of a large number of data i.e. creation of lareg number lithologic log plots in a short period of time (the paper is published in Croatian.

  2. Assessing Elementary Algebra with STACK

    Science.gov (United States)

    Sangwin, Christopher J.

    2007-01-01

    This paper concerns computer aided assessment (CAA) of mathematics in which a computer algebra system (CAS) is used to help assess students' responses to elementary algebra questions. Using a methodology of documentary analysis, we examine what is taught in elementary algebra. The STACK CAA system, http://www.stack.bham.ac.uk/, which uses the CAS…

  3. HPC Software Stack Testing Framework

    Energy Technology Data Exchange (ETDEWEB)

    2017-07-27

    The HPC Software stack testing framework (hpcswtest) is used in the INL Scientific Computing Department to test the basic sanity and integrity of the HPC Software stack (Compilers, MPI, Numerical libraries and Applications) and to quickly discover hard failures, and as a by-product it will indirectly check the HPC infrastructure (network, PBS and licensing servers).

  4. Efficiency of Polymer Electrolyte Membrane Fuel Cell Stack

    Directory of Open Access Journals (Sweden)

    Hans Bosma

    2011-08-01

    Full Text Available This paper applies a feedforward control of optimal oxygen excess ratio that maximize net power (improve efficiency of a NedStack P8.0-64 PEM fuel cell stack (FCS system. Net powers profile as a function of oxygen excess ratio for some points of operation are analyzed by using FCS model. The relationships between stack current and the corresponding control input voltage that gives an optimal oxygen excess ratio are used to design a feedforward control scheme. The results of this scheme are compared to the results of a feedforward control using a constant oxygen excess ratio. Simulation results show that optimal oxygen excess ratio improves fuel cell performance compared to the results of constant oxygen excess ratio. The same procedures are performed experimentally for the FCS system. The behaviour of the net power of the fuel cell stack with respect to the variation of oxygen excess ratio is analyzed to obtain optimal values. Data of stack current and the corresponding voltage input to the compressor that gives optimal values of oxygen excess ratio are used to develop a feedforward control. Feedforward control based on constant and optimal oxygen excess ratio control, are implemented in the NedStack P8.0-64 PEM fuel cell stack system by using LabVIEW. Implementation results shows that optimal oxygen excess ratio control improves the fuel cell performance compared to the constant oxygen excess ratio control.

  5. SEE on Different Layers of Stacked-SRAMs

    CERN Document Server

    Gupta, V; Tsiligiannis, G; Rousselet, M; Mohammadzadeh, A; Javanainen, A; Virtanen, A; Puchner, H; Saigné, F; Wrobel, F; Dilillo, L

    2015-01-01

    This paper presents heavy-ion and proton radiation test results of a 90 nm COTS SRAM with stacked structure. Radiation tests were made using high penetration heavy-ion cocktails at the HIF (Belgium) and at RADEF (Finland) as well as low energy protons at RADEF. The heavy-ion SEU cross-section showed an unusual profile with a peak at the lowest LET (heavy-ion with the highest penetration range). The discrepancy is due to the fact that the SRAM is constituted of two vertically stacked dice. The impact of proton testing on the response of both stacked dice is presented. The results are discussed and the SEU cross-sections of the upper and lower layers are compared. The impact of the stacked structure on the proton SEE rate is investigated.

  6. Profiles

    International Nuclear Information System (INIS)

    2004-01-01

    Profiles is a synthetic overview of more than 100 national energy markets in the world, providing insightful facts and key energy statistics. A Profile is structured around 6 main items and completed by key statistics: Ministries, public agencies, energy policy are concerned; main companies in the oil, gas, electricity and coal sectors, status, shareholders; reserve, production, imports and exports, electricity and refining capacities; deregulation of prices, subsidies, taxes; consumption trends by sector, energy market shares; main energy projects, production and consumption prospects. Statistical Profiles are present in about 3 pages the main data and indicators on oil, gas, coal and electricity. (A.L.B.)

  7. Environmental assessment of phosphogypsum stacks

    International Nuclear Information System (INIS)

    Odat, M.; Al-Attar, L.; Raja, G.; Abdul Ghany, B.

    2008-03-01

    Phosphogypsum is one of the most important by-products of phosphate fertilizer industry. It is kept in large stacks to the west of Homs city. Storing Phosphogypsum as open stacks exposed to various environmental effects, wind and rain, may cause pollution of the surrounding ecosystem (soil, plant, water and air). This study was carried out in order to assess the environmental impact of Phosphogypsum stacks on the surrounding ecosystem. The obtained results show that Phosphogypsum stacks did not increase the concentration of radionuclides, i.e. Radon-222 and Radium-226, the external exposed dose of gamma rays, as well as the concentration of heavy metals in the components of the ecosystem, soil, plant, water and air, as their concentrations did not exceed the permissible limits. However, the concentration of fluorine in the upper layer of soil, located to the east of the Phosphogypsum stacks, increased sufficiently, especially in the dry period of the year. Also, the concentration of fluoride in plants growing up near-by the Phosphogypsum stacks was too high, exceeded the permissible levels. This was reflected in poising plants and animals, feeding on the plants. Consequently, increasing the concentration of fluoride in soil and plants is the main impact of Phosphogypsum stacks on the surrounding ecosystem. Minimising this effect could be achieved by establishing a 50 meter wide protection zone surrounding the Phosphogypsum stacks, which has to be planted with non palatable trees, such as pine and cypress, forming wind barriers. Increasing the concentrations of heavy metals and fluoride in infiltrated water around the stacks was high; hence cautions must be taken to prevent its usage in any application or disposal in adjacent rivers and leaks.(author)

  8. Multiple hypothesis clustering in radar plot extraction

    NARCIS (Netherlands)

    Huizing, A.G.; Theil, A.; Dorp, Ph. van; Ligthart, L.P.

    1995-01-01

    False plots and plots with inaccurate range and Doppler estimates may severely degrade the performance of tracking algorithms in radar systems. This paper describes how a multiple hypothesis clustering technique can be applied to mitigate the problems involved in plot extraction. The measures of

  9. PieceStack: Toward Better Understanding of Stacked Graphs.

    Science.gov (United States)

    Wu, Tongshuang; Wu, Yingcai; Shi, Conglei; Qu, Huamin; Cui, Weiwei

    2016-02-24

    Stacked graphs have been widely adopted in various fields, because they are capable of hierarchically visualizing a set of temporal sequences as well as their aggregation. However, because of visual illusion issues, connections between overly-detailed individual layers and overly-generalized aggregation are intercepted. Consequently, information in this area has yet to be fully excavated. Thus, we present PieceStack in this paper, to reveal the relevance of stacked graphs in understanding intrinsic details of their displayed shapes. This new visual analytic design interprets the ways through which aggregations are generated with individual layers by interactively splitting and re-constructing the stacked graphs. A clustering algorithm is designed to partition stacked graphs into sub-aggregated pieces based on trend similarities of layers. We then visualize the pieces with augmented encoding to help analysts decompose and explore the graphs with respect to their interests. Case studies and a user study are conducted to demonstrate the usefulness of our technique in understanding the formation of stacked graphs.

  10. New systems for photogrametric plotting

    International Nuclear Information System (INIS)

    Diaz Munoz, J.J.; Sarti Balsalobre, F.

    1995-01-01

    Ground photogrammetry is a highly useful technique for up-dating as-built documentation of nuclear power plants as it has the following advantages: - It reduces radiation exposure - It provides information concerning all the structures, equipment, components, pipe lines, etc, in the zone - it avoids errors made in the interpretation of drawings In the past, the application of non-topographic photogrammetry was limited by the need to use costly restitution equipment, until computer technology made it possible to operate complete photogrametric systems using a PC, digitizer, the appropriate software and a simple 35 mm camera. It is not necessary to use a tripod, or known the location of the camera or that the photographs are stereoscopic pairs. The plotting process is basically reduced to placing the photographs on the digitizing board, making the necessary adjustments and obtaining the coordinates of each point indicated. This paper explains the new photogrametric tools currently on the market, the theory behind them, and their advantages and disadvantages. It also describes some of the applications of advanced photogrammetry applied to design modifications in the nuclear sector, performed using the Empresarios Agrupados Metadat System. (Author)

  11. Stacking faults and microstructural parameters in non-mulberry silk ...

    Indian Academy of Sciences (India)

    Then the whole pattern fitting was done by introducing weight factors for the individual profiles and also taking into account the average stacking faults derived using eqs (4) and (5) in the final stage of refinement with the whole experimental diffraction data of the sample. Computational procedure is given in the flow chart ...

  12. Fifth International Symposium on Recurrence Plot

    CERN Document Server

    Riley, Michael; Giuliani, Alessandro; Webber, Charles; Jr, Jr; Translational Recurrences : From Mathematical Theory to Real-World Applications

    2014-01-01

    This book features 13 papers presented at the Fifth International Symposium on Recurrence Plots, held August 2013 in Chicago, IL. It examines recent applications and developments in recurrence plots and recurrence quantifi cation analysis (RQA) with special emphasis on biological and cognitive systems and the analysis of coupled systems using cross-recurrence methods. Readers will discover new applications and insights into a range of systems provided by recurrence plot analysis and new theoretical and mathematical developments in recurrence plots. Recurrence plot based analysis is a powerful tool that operates on real-world complex systems that are nonlinear, non-stationary, noisy, of any statistical distribution, free of any particular model type, and not particularly long. Quantitative analyses promote the detection of system state changes, synchronized dynamical regimes, or classifi cation of system states. Th e book will be of interest to an interdisciplinary audience of recurrence plot users and researc...

  13. Seismic fragility of ventilation stack of nuclear power plant

    International Nuclear Information System (INIS)

    Nefedov, S.S.; Yugai, T.Z.; Kalinkin, I.V.; Vizir, P.L.

    2003-01-01

    Fragility study of safety related elements is necessary step in seismic PSA of nuclear power plant (NPP). In present work fragility was analyzed after the example of the ventilation stack of NPP. Ventilation stack, considered in present work, is a separately erected construction with height of 100 m made of cast-in-place reinforced concrete. In accordance with IAEA terminology fragility of element is defined as conditional probability of its failure at given level of seismic loading. Failure of a ventilation stack was considered as development of the plastic hinge in some section of a shaft. Seismic ground acceleration a, which corresponds to failure, could be defined as limit seismic acceleration of ventilation stack [a]. Limit seismic acceleration [a] was considered as random value. Sources of its variation are connected with stochastic nature of factors determining it (properties of construction materials, soils etc.), and also with uncertainties of existing analytical techniques. Random value [a] was assumed to be distributed lognormally. Median m[a] and logarithmically standard deviation β of this distribution were defined by 'scaling method' developed by R.P. Kennedy et al. Using this values fragility curves were plotted for different levels of confidence probability. (author)

  14. System for histogram entry, retrieval, and plotting

    International Nuclear Information System (INIS)

    Kellogg, M.; Gallup, J.M.; Shlaer, S.; Spencer, N.

    1977-10-01

    This manual describes the systems for producing histograms and dot plots that were designed for use in connection with the Q general-purpose data-acquisition system. These systems allow for the creation of histograms; the entry, retrieval, and plotting of data in the form of histograms; and the dynamic display of scatter plots as data are acquired. Although the systems are designed for use with Q, they can also be used as a part of other applications. 3 figures

  15. Representing uncertainty on model analysis plots

    Directory of Open Access Journals (Sweden)

    Trevor I. Smith

    2016-09-01

    Full Text Available Model analysis provides a mechanism for representing student learning as measured by standard multiple-choice surveys. The model plot contains information regarding both how likely students in a particular class are to choose the correct answer and how likely they are to choose an answer consistent with a well-documented conceptual model. Unfortunately, Bao’s original presentation of the model plot did not include a way to represent uncertainty in these measurements. I present details of a method to add error bars to model plots by expanding the work of Sommer and Lindell. I also provide a template for generating model plots with error bars.

  16. An Excel macro for generating trilinear plots.

    Science.gov (United States)

    Shikaze, Steven G; Crowe, Allan S

    2007-01-01

    This computer note describes a method for creating trilinear plots in Microsoft Excel. Macros have been created in MS Excel's internal language: Visual Basic for Applications (VBA). A simple form has been set up to allow the user to input data from an Excel worksheet. The VBA macro is used to convert the triangular data (which consist of three columns of percentage data) into X-Y data. The macro then generates the axes, labels, and grid for the trilinear plot. The X-Y data are plotted as scatter data in Excel. By providing this macro in Excel, users can create trilinear plots in a quick, inexpensive manner.

  17. Characterisation and Modelling of a High Temperature PEM Fuel Cell Stack using Electrochemical Impedance Spectroscopy

    DEFF Research Database (Denmark)

    Andreasen, Søren Juhl; Jespersen, Jesper Lebæk; Schaltz, Erik

    2009-01-01

    temperature PEM (HTPEM) fuel cell stack. A Labview virtual instrument has been developed to perform the signal generation and data acquisition which is needed to perform EIS. The typical output of an EIS measurement on a fuel cell, is a Nyquist plot, which shows the imaginary and real part of the impedance...

  18. Time-predictable Stack Caching

    DEFF Research Database (Denmark)

    Abbaspourseyedi, Sahar

    completely. Thus, in systems with hard deadlines the worst-case execution time (WCET) of the real-time software running on them needs to be bounded. Modern architectures use features such as pipelining and caches for improving the average performance. These features, however, make the WCET analysis more...... addresses, provides an opportunity to predict and tighten the WCET of accesses to data in caches. In this thesis, we introduce the time-predictable stack cache design and implementation within a time-predictable processor. We introduce several optimizations to our design for tightening the WCET while...... keeping the timepredictability of the design intact. Moreover, we provide a solution for reducing the cost of context switching in a system using the stack cache. In design of these caches, we use custom hardware and compiler support for delivering time-predictable stack data accesses. Furthermore...

  19. Glassy carbon based supercapacitor stacks

    Energy Technology Data Exchange (ETDEWEB)

    Baertsch, M.; Braun, A.; Koetz, R.; Haas, O. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1997-06-01

    Considerable effort is being made to develop electrochemical double layer capacitors (EDLC) that store relatively large quantities of electrical energy and possess at the same time a high power density. Our previous work has shown that glassy carbon is suitable as a material for capacitor electrodes concerning low resistance and high capacity requirements. We present the development of bipolar electrochemical glassy carbon capacitor stacks of up to 3 V. Bipolar stacks are an efficient way to meet the high voltage and high power density requirements for traction applications. Impedance and cyclic voltammogram measurements are reported here and show the frequency response of a 1, 2, and 3 V stack. (author) 3 figs., 1 ref..

  20. Multiple Segmentation of Image Stacks

    DEFF Research Database (Denmark)

    Smets, Jonathan; Jaeger, Manfred

    2014-01-01

    We propose a method for the simultaneous construction of multiple image segmentations by combining a recently proposed “convolution of mixtures of Gaussians” model with a multi-layer hidden Markov random field structure. The resulting method constructs for a single image several, alternative...... segmentations that capture different structural elements of the image. We also apply the method to collections of images with identical pixel dimensions, which we call image stacks. Here it turns out that the method is able to both identify groups of similar images in the stack, and to provide segmentations...

  1. Simulating Small-Scale Object Stacking Using Stack Stability

    DEFF Research Database (Denmark)

    Kronborg Thomsen, Kasper; Kraus, Martin

    2015-01-01

    This paper presents an extension system to a closed-source, real-time physics engine for improving structured stacking behavior with small-scale objects such as wooden toy bricks. The proposed system was implemented and evaluated. The tests showed that the system is able to simulate several common...

  2. Plotting system for the MINCS code

    International Nuclear Information System (INIS)

    Watanabe, Tadashi

    1990-08-01

    The plotting system for the MINCS code is described. The transient two-phase flow analysis code MINCS has been developed to provide a computational tool for analysing various two-phase flow phenomena in one-dimensional ducts. Two plotting systems, namely the SPLPLOT system and the SDPLOT system, can be used as the plotting functions. The SPLPLOT system is used for plotting time transients of variables, while the SDPLOT system is for spatial distributions. The SPLPLOT system is based on the SPLPACK system, which is used as a general tool for plotting results of transient analysis codes or experiments. The SDPLOT is based on the GPLP program, which is also regarded as one of the general plotting programs. In the SPLPLOT and the SDPLOT systems, the standardized data format called the SPL format is used in reading data to be plotted. The output data format of MINCS is translated into the SPL format by using the conversion system called the MINTOSPL system. In this report, how to use the plotting functions is described. (author)

  3. The Heuristic Interpretation of Box Plots

    Science.gov (United States)

    Lem, Stephanie; Onghena, Patrick; Verschaffel, Lieven; Van Dooren, Wim

    2013-01-01

    Box plots are frequently used, but are often misinterpreted by students. Especially the area of the box in box plots is often misinterpreted as representing number or proportion of observations, while it actually represents their density. In a first study, reaction time evidence was used to test whether heuristic reasoning underlies this…

  4. Reaction Order Ambiguity in Integrated Rate Plots

    Science.gov (United States)

    Lee, Joe

    2008-01-01

    Integrated rate plots are frequently used in reaction kinetics to determine orders of reactions. It is often emphasised, when using this methodology in practice, that it is necessary to monitor the reaction to a substantial fraction of completion for these plots to yield unambiguous orders. The present article gives a theoretical and statistical…

  5. Digital data collection in forest dynamics plots

    Science.gov (United States)

    Faith Inman-Narahari; Christian Giardina; Rebecca Ostertag; Susan Cordell; Lawren Sack

    2010-01-01

    Summary 1. Computers are widely used in all aspects of research but their application to in-field data collection for forest plots has rarely been evaluated. 2. We developed digital data collection methods using ESRI mapping software and ruggedized field computers to map and measure ~30 000 trees in two 4-ha forest dynamics plots in wet and dry...

  6. Corrections for Cluster-Plot Slop

    Science.gov (United States)

    Harry T. Valentine; Mark J. Ducey; Jeffery H. Gove; Adrian Lanz; David L.R. Affleck

    2006-01-01

    Cluster-plot designs, including the design used by the Forest Inventory and Analysis program of the USDA Forest Service (FIA), are attended by a complicated boundary slopover problem. Slopover occurs where inclusion zones of objects of interest cross the boundary of the area of interest. The dispersed nature of inclusion zones that arise from the use of cluster plots...

  7. Pressurized electrolysis stack with thermal expansion capability

    Science.gov (United States)

    Bourgeois, Richard Scott

    2015-07-14

    The present techniques provide systems and methods for mounting an electrolyzer stack in an outer shell so as to allow for differential thermal expansion of the electrolyzer stack and shell. Generally, an electrolyzer stack may be formed from a material with a high coefficient of thermal expansion, while the shell may be formed from a material having a lower coefficient of thermal expansion. The differences between the coefficients of thermal expansion may lead to damage to the electrolyzer stack as the shell may restrain the thermal expansion of the electrolyzer stack. To allow for the differences in thermal expansion, the electrolyzer stack may be mounted within the shell leaving a space between the electrolyzer stack and shell. The space between the electrolyzer stack and the shell may be filled with a non-conductive fluid to further equalize pressure inside and outside of the electrolyzer stack.

  8. The Direct FuelCell™ stack engineering

    Science.gov (United States)

    Doyon, J.; Farooque, M.; Maru, H.

    FuelCell Energy (FCE) has developed power plants in the size range of 300 kW to 3 MW for distributed power generation. Field-testing of the sub-megawatt plants is underway. The FCE power plants are based on its Direct FuelCell™ (DFC) technology. This is so named because of its ability to generate electricity directly from a hydrocarbon fuel, such as natural gas, by reforming it inside the fuel cell stack itself. All FCE products use identical 8000 cm 2 cell design, approximately 350-400 cells per stack, external gas manifolds, and similar stack compression systems. The difference lies in the packaging of the stacks inside the stack module. The sub-megawatt system stack module contains a single horizontal stack whereas the MW-class stack module houses four identical vertical stacks. The commonality of the design, internal reforming features, and atmospheric operation simplify the system design, reduce cost, improve efficiency, increase reliability and maintainability. The product building-block stack design has been advanced through three full-size stack operations at company's headquarters in Danbury, CT. The initial proof-of-concept of the full-size stack design was verified in 1999, followed by a 1.5 year of endurance verification in 2000-2001, and currently a value-engineered stack version is in operation. This paper discusses the design features, important engineering solutions implemented, and test results of FCE's full-size DFC stacks.

  9. Stack semantics of type theory

    DEFF Research Database (Denmark)

    Coquand, Thierry; Mannaa, Bassel; Ruch, Fabian

    2017-01-01

    We give a model of dependent type theory with one univalent universe and propositional truncation interpreting a type as a stack, generalizing the groupoid model of type theory. As an application, we show that countable choice cannot be proved in dependent type theory with one univalent universe...

  10. Multilayer Piezoelectric Stack Actuator Characterization

    Science.gov (United States)

    Sherrit, Stewart; Jones, Christopher M.; Aldrich, Jack B.; Blodget, Chad; Bao, Xioaqi; Badescu, Mircea; Bar-Cohen, Yoseph

    2008-01-01

    Future NASA missions are increasingly seeking to use actuators for precision positioning to accuracies of the order of fractions of a nanometer. For this purpose, multilayer piezoelectric stacks are being considered as actuators for driving these precision mechanisms. In this study, sets of commercial PZT stacks were tested in various AC and DC conditions at both nominal and extreme temperatures and voltages. AC signal testing included impedance, capacitance and dielectric loss factor of each actuator as a function of the small-signal driving sinusoidal frequency, and the ambient temperature. DC signal testing includes leakage current and displacement as a function of the applied DC voltage. The applied DC voltage was increased to over eight times the manufacturers' specifications to investigate the correlation between leakage current and breakdown voltage. Resonance characterization as a function of temperature was done over a temperature range of -180C to +200C which generally exceeded the manufacturers' specifications. In order to study the lifetime performance of these stacks, five actuators from one manufacturer were driven by a 60volt, 2 kHz sine-wave for ten billion cycles. The tests were performed using a Lab-View controlled automated data acquisition system that monitored the waveform of the stack electrical current and voltage. The measurements included the displacement, impedance, capacitance and leakage current and the analysis of the experimental results will be presented.

  11. Open stack thermal battery tests

    Energy Technology Data Exchange (ETDEWEB)

    Long, Kevin N. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Roberts, Christine C. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Grillet, Anne M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Headley, Alexander J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Fenton, Kyle [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Wong, Dennis [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Ingersoll, David [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-04-17

    We present selected results from a series of Open Stack thermal battery tests performed in FY14 and FY15 and discuss our findings. These tests were meant to provide validation data for the comprehensive thermal battery simulation tools currently under development in Sierra/Aria under known conditions compared with as-manufactured batteries. We are able to satisfy this original objective in the present study for some test conditions. Measurements from each test include: nominal stack pressure (axial stress) vs. time in the cold state and during battery ignition, battery voltage vs. time against a prescribed current draw with periodic pulses, and images transverse to the battery axis from which cell displacements are computed. Six battery configurations were evaluated: 3, 5, and 10 cell stacks sandwiched between 4 layers of the materials used for axial thermal insulation, either Fiberfrax Board or MinK. In addition to the results from 3, 5, and 10 cell stacks with either in-line Fiberfrax Board or MinK insulation, a series of cell-free “control” tests were performed that show the inherent settling and stress relaxation based on the interaction between the insulation and heat pellets alone.

  12. Adding large EM stack support

    KAUST Repository

    Holst, Glendon

    2016-12-01

    Serial section electron microscopy (SSEM) image stacks generated using high throughput microscopy techniques are an integral tool for investigating brain connectivity and cell morphology. FIB or 3View scanning electron microscopes easily generate gigabytes of data. In order to produce analyzable 3D dataset from the imaged volumes, efficient and reliable image segmentation is crucial. Classical manual approaches to segmentation are time consuming and labour intensive. Semiautomatic seeded watershed segmentation algorithms, such as those implemented by ilastik image processing software, are a very powerful alternative, substantially speeding up segmentation times. We have used ilastik effectively for small EM stacks – on a laptop, no less; however, ilastik was unable to carve the large EM stacks we needed to segment because its memory requirements grew too large – even for the biggest workstations we had available. For this reason, we refactored the carving module of ilastik to scale it up to large EM stacks on large workstations, and tested its efficiency. We modified the carving module, building on existing blockwise processing functionality to process data in manageable chunks that can fit within RAM (main memory). We review this refactoring work, highlighting the software architecture, design choices, modifications, and issues encountered.

  13. A first look at measurement error on FIA plots using blind plots in the Pacific Northwest

    Science.gov (United States)

    Susanna Melson; David Azuma; Jeremy S. Fried

    2002-01-01

    Measurement error in the Forest Inventory and Analysis work of the Pacific Northwest Station was estimated with a recently implemented blind plot measurement protocol. A small subset of plots was revisited by a crew having limited knowledge of the first crew's measurements. This preliminary analysis of the first 18 months' blind plot data indicates that...

  14. Development and durability of SOFC stacks

    Energy Technology Data Exchange (ETDEWEB)

    Beeaff, D.; Dinesen, A.R.; Mikkelsen, Lars; Nielsen, Karsten A.; Solvang, M.; Hendriksen, Peter V.

    2004-12-01

    The present project is a part of the Danish SOFC programme, which has the overall aim of establishing a Danish production of SOFC - cells, stacks and systems for economical and environmentally friendly power production. The aim of the present project was to develop and demonstrate (on a small scale, few cells, few thousand hours) a durable, thermally cyclable stack with high performance at 750 deg. C. Good progress towards this target has been made and demonstrated at the level of stack-elements (one cell between two interconnects) or small stacks (3 5 cells). Three different stacks or stack-elements have been operated for periods exceeding 3000 hr. The work has covered development of stack-components (seals, interconnects, coatings, contact layers), establishment of procedures for stack assembly and initiation, and detailed electrical characterisation with the aims of identifying performance limiting factors as well as long term durability. Further, post test investigations have been carried out to identify possible degradation mechanisms. (BA)

  15. Market principles toward the land plots assessment

    OpenAIRE

    A. Koshel

    2015-01-01

    Market principles toward the agricultural land plots assessment and the features are analyzed. The detailed study of economic valuation principles of agricultural land is conducted. Application of the principles of such evaluation in the process of mass valuation is suggested

  16. Experimental Garden Plots for Botany Lessons

    Science.gov (United States)

    Gorodnicheva, V. V.; Vasil'eva, E. I.

    1976-01-01

    Discussion of the botany lessons used at two schools points out the need for fifth and sixth grade students to be taught the principles of plant life through observations made at an experimental garden plot at the school. (ND)

  17. Simulation Branch Plotting and Utility Routines 1

    Science.gov (United States)

    1975-03-01

    rights or permission to manufacture , use, or sell any patented invention that may in any way be related thereto. IS This technical report has been...NOTES ■ „ FTN (Fortran IV Extended) Plotting package 2-D magnetohydrodynamics Microfilm BRAHMA SCOPE 3.2 -rr ,, net.0,sarv and identity by...maqnetohydrodynamics code BRAHMA . Section I is concerned with microfilm plotting routines. Section II is primarily concerned with utility routines

  18. Development of TRatioPlot in ROOT

    CERN Document Server

    Gessinger-Befurt, Paul

    2016-01-01

    The ROOT data analysis and visualization framework is a software package which is widely used in physics, especially in high energy physics. A common visualization which has so far been lacking a direct implementation is the ratio plot, as well as a few similar types of plots. The scope and goal of the summer student project at CERN was to implement a class in ROOT itself, that can take care of the most common types of calculations, and produces high quality visuals.

  19. Using funnel plots in public health surveillance

    Directory of Open Access Journals (Sweden)

    Dover Douglas C

    2011-11-01

    Full Text Available Abstract Background Public health surveillance is often concerned with the analysis of health outcomes over small areas. Funnel plots have been proposed as a useful tool for assessing and visualizing surveillance data, but their full utility has not been appreciated (for example, in the incorporation and interpretation of risk factors. Methods We investigate a way to simultaneously focus funnel plot analyses on direct policy implications while visually incorporating model fit and the effects of risk factors. Health survey data representing modifiable and nonmodifiable risk factors are used in an analysis of 2007 small area motor vehicle mortality rates in Alberta, Canada. Results Small area variations in motor vehicle mortality in Alberta were well explained by the suite of modifiable and nonmodifiable risk factors. Funnel plots of raw rates and of risk adjusted rates lead to different conclusions; the analysis process highlights opportunities for intervention as risk factors are incorporated into the model. Maps based on funnel plot methods identify areas worthy of further investigation. Conclusions Funnel plots provide a useful tool to explore small area data and to routinely incorporate covariate relationships in surveillance analyses. The exploratory process has at each step a direct and useful policy-related result. Dealing thoughtfully with statistical overdispersion is a cornerstone to fully understanding funnel plots.

  20. Using funnel plots in public health surveillance.

    Science.gov (United States)

    Dover, Douglas C; Schopflocher, Donald P

    2011-11-10

    Public health surveillance is often concerned with the analysis of health outcomes over small areas. Funnel plots have been proposed as a useful tool for assessing and visualizing surveillance data, but their full utility has not been appreciated (for example, in the incorporation and interpretation of risk factors). We investigate a way to simultaneously focus funnel plot analyses on direct policy implications while visually incorporating model fit and the effects of risk factors. Health survey data representing modifiable and nonmodifiable risk factors are used in an analysis of 2007 small area motor vehicle mortality rates in Alberta, Canada. Small area variations in motor vehicle mortality in Alberta were well explained by the suite of modifiable and nonmodifiable risk factors. Funnel plots of raw rates and of risk adjusted rates lead to different conclusions; the analysis process highlights opportunities for intervention as risk factors are incorporated into the model. Maps based on funnel plot methods identify areas worthy of further investigation. Funnel plots provide a useful tool to explore small area data and to routinely incorporate covariate relationships in surveillance analyses. The exploratory process has at each step a direct and useful policy-related result. Dealing thoughtfully with statistical overdispersion is a cornerstone to fully understanding funnel plots.

  1. Lightweight Stacks of Direct Methanol Fuel Cells

    Science.gov (United States)

    Narayanan, Sekharipuram; Valdez, Thomas

    2004-01-01

    An improved design concept for direct methanol fuel cells makes it possible to construct fuel-cell stacks that can weigh as little as one-third as much as do conventional bipolar fuel-cell stacks of equal power. The structural-support components of the improved cells and stacks can be made of relatively inexpensive plastics. Moreover, in comparison with conventional bipolar fuel-cell stacks, the improved fuel-cell stacks can be assembled, disassembled, and diagnosed for malfunctions more easily. These improvements are expected to bring portable direct methanol fuel cells and stacks closer to commercialization. In a conventional bipolar fuel-cell stack, the cells are interspersed with bipolar plates (also called biplates), which are structural components that serve to interconnect the cells and distribute the reactants (methanol and air). The cells and biplates are sandwiched between metal end plates. Usually, the stack is held together under pressure by tie rods that clamp the end plates. The bipolar stack configuration offers the advantage of very low internal electrical resistance. However, when the power output of a stack is only a few watts, the very low internal resistance of a bipolar stack is not absolutely necessary for keeping the internal power loss acceptably low.

  2. Solid Oxide Fuel Cell Stack Diagnostics

    DEFF Research Database (Denmark)

    Mosbæk, Rasmus Rode; Barfod, Rasmus Gottrup

    . An operating stack is subject to compositional gradients in the gaseous reactant streams, and temperature gradients across each cell and across the stack, which complicates detailed analysis. Several experimental stacks from Topsoe Fuel Cell A/S were characterized using Electrochemical Impedance Spectroscopy...... (EIS). The stack measurement geometry was optimized for EIS by careful selection of the placement of current feeds and voltage probes in order to minimize measurement errors. It was demonstrated that with the improved placement of current feeds and voltage probes it is possible to separate the loss...... in the hydrogen fuel gas supplied to the stack. EIS was used to examine the long-term behavior and monitor the evolution of the impedance of each of the repeating units and the whole stack. The observed impedance was analyzed in detail for one of the repeating units and the whole stack and the losses reported...

  3. [Comparative quality measurements part 3: funnel plots].

    Science.gov (United States)

    Kottner, Jan; Lahmann, Nils

    2014-02-01

    Comparative quality measurements between organisations or institutions are common. Quality measures need to be standardised and risk adjusted. Random error must also be taken adequately into account. Rankings without consideration of the precision lead to flawed interpretations and enhances "gaming". Application of confidence intervals is one possibility to take chance variation into account. Funnel plots are modified control charts based on Statistical Process Control (SPC) theory. The quality measures are plotted against their sample size. Warning and control limits that are 2 or 3 standard deviations from the center line are added. With increasing group size the precision increases and so the control limits are forming a funnel. Data points within the control limits are considered to show common cause variation; data points outside special cause variation without the focus of spurious rankings. Funnel plots offer data based information about how to evaluate institutional performance within quality management contexts.

  4. 6th International Symposium on Recurrence Plots

    CERN Document Server

    Jr, Jr; Ioana, Cornel; Marwan, Norbert

    2016-01-01

    The chapters in this book originate from the research work and contributions presented at the Sixth International Symposium on Recurrence Plots held in Grenoble, France in June 2015. Scientists from numerous disciplines gathered to exchange knowledge on recent applications and developments in recurrence plots and recurrence quantification analysis. This meeting was remarkable because of the obvious expansion of recurrence strategies (theory) and applications (practice) into ever-broadening fields of science. It discusses real-world systems from various fields, including mathematics, strange attractors, applied physics, physiology, medicine, environmental and earth sciences, as well as psychology and linguistics. Even readers not actively researching any of these particular systems will benefit from discovering how other scientists are finding practical non-linear solutions to specific problems. The book is of interest to an interdisciplinary audience of recurrence plot users and researchers interested in time...

  5. Data Quality Objectives Summary Report for the Demolition of the 116-D and 116-DR Stacks

    International Nuclear Information System (INIS)

    Adler, J. G.

    1999-01-01

    This data quality objective (DQO) summary report has been developed to support demolition and disposal of the 116-D and 116-DR stacks in the 100-D Area of the Hanford Site. This project-specific summary was developed to meet the requirements in BHI-EE-01, Environmental Investigations Procedures, Procedure 1.2, ''Data Quality Objectives,'' using a simplified DQO process. The pathway for disposal of the 116-D and 116-DR stacks is the Environmental Restoration Disposal Facility (ERDF), which requires the development of a waste profile. A combination of process knowledge, history, and existing analogous data will be used to build a waste profile to dispose of the stack and plenum debris in the ERDF. Additional sample data are not necessary for waste designation. This report also addresses the Resources, Conservation, and Recovery Act of 1976 treatment, storage, and disposal closure requirements associated with the 116-DR stack

  6. PLOT3D Export Tool for Tecplot

    Science.gov (United States)

    Alter, Stephen

    2010-01-01

    The PLOT3D export tool for Tecplot solves the problem of modified data being impossible to output for use by another computational science solver. The PLOT3D Exporter add-on enables the use of the most commonly available visualization tools to engineers for output of a standard format. The exportation of PLOT3D data from Tecplot has far reaching effects because it allows for grid and solution manipulation within a graphical user interface (GUI) that is easily customized with macro language-based and user-developed GUIs. The add-on also enables the use of Tecplot as an interpolation tool for solution conversion between different grids of different types. This one add-on enhances the functionality of Tecplot so significantly, it offers the ability to incorporate Tecplot into a general suite of tools for computational science applications as a 3D graphics engine for visualization of all data. Within the PLOT3D Export Add-on are several functions that enhance the operations and effectiveness of the add-on. Unlike Tecplot output functions, the PLOT3D Export Add-on enables the use of the zone selection dialog in Tecplot to choose which zones are to be written by offering three distinct options - output of active, inactive, or all zones (grid blocks). As the user modifies the zones to output with the zone selection dialog, the zones to be written are similarly updated. This enables the use of Tecplot to create multiple configurations of a geometry being analyzed. For example, if an aircraft is loaded with multiple deflections of flaps, by activating and deactivating different zones for a specific flap setting, new specific configurations of that aircraft can be easily generated by only writing out specific zones. Thus, if ten flap settings are loaded into Tecplot, the PLOT3D Export software can output ten different configurations, one for each flap setting.

  7. Cfd Analysis of Heat Transfer in a Microtubular Solid Oxide Fuel Cell Stack

    Directory of Open Access Journals (Sweden)

    Pianko-Oprych Paulina

    2014-09-01

    Full Text Available The aim of this work was to achieve a deeper understanding of the heat transfer in a microtubular Solid Oxide Fuel Cell (mSOFC stack based on the results obtained by means of a Computational Fluid Dynamics tool. Stack performance predictions were based on simulations for a 16 anodesupported mSOFCs sub-stack, which was a component of the overall stack containing 64 fuel cells. The emphasis of the paper was put on steady-state modelling, which enabled identification of heat transfer between the fuel cells and air flow cooling the stack and estimation of the influence of stack heat losses. Analysis of processes for different heat losses and the impact of the mSOFC reaction heat flux profile on the temperature distribution in the mSOFC stack were carried out. Both radiative and convective heat transfer were taken into account in the analysis. Two different levels of the inlet air velocity and three different values of the heat losses were considered. Good agreement of the CFD model results with experimental data allowed to predict the operation trends, which will be a reliable tool for optimisation of the working setup and ensure sufficient cooling of the mSOFC stack.

  8. Application of mapped plots for single-owner forest surveys

    Science.gov (United States)

    Paul C. Van Deusen; Francis Roesch

    2009-01-01

    Mapped plots are used for the nation forest inventory conducted by the U.S. Forest Service. Mapped plots are also useful foro single ownership inventoires. Mapped plots can handle boundary overlap and can aprovide less variable estimates for specified forest conditions. Mapping is a good fit for fixed plot inventories where the fixed area plot is used for both mapping...

  9. Vertically stacked nanocellulose tactile sensor.

    Science.gov (United States)

    Jung, Minhyun; Kim, Kyungkwan; Kim, Bumjin; Lee, Kwang-Jae; Kang, Jae-Wook; Jeon, Sanghun

    2017-11-16

    Paper-based electronic devices are attracting considerable attention, because the paper platform has unique attributes such as flexibility and eco-friendliness. Here we report on what is claimed to be the firstly fully integrated vertically-stacked nanocellulose-based tactile sensor, which is capable of simultaneously sensing temperature and pressure. The pressure and temperature sensors are operated using different principles and are stacked vertically, thereby minimizing the interference effect. For the pressure sensor, which utilizes the piezoresistance principle under pressure, the conducting electrode was inkjet printed on the TEMPO-oxidized-nanocellulose patterned with micro-sized pyramids, and the counter electrode was placed on the nanocellulose film. The pressure sensor has a high sensitivity over a wide range (500 Pa-3 kPa) and a high durability of 10 4 loading/unloading cycles. The temperature sensor combines various materials such as poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS), silver nanoparticles (AgNPs) and carbon nanotubes (CNTs) to form a thermocouple on the upper nanocellulose layer. The thermoelectric-based temperature sensors generate a thermoelectric voltage output of 1.7 mV for a temperature difference of 125 K. Our 5 × 5 tactile sensor arrays show a fast response, negligible interference, and durable sensing performance.

  10. Representing Uncertainty on Model Analysis Plots

    Science.gov (United States)

    Smith, Trevor I.

    2016-01-01

    Model analysis provides a mechanism for representing student learning as measured by standard multiple-choice surveys. The model plot contains information regarding both how likely students in a particular class are to choose the correct answer and how likely they are to choose an answer consistent with a well-documented conceptual model.…

  11. A reduced volumetric expansion factor plot

    Science.gov (United States)

    Hendricks, R. C.

    1979-01-01

    A reduced volumetric expansion factor plot has been constructed for simple fluids which is suitable for engineering computations in heat transfer. Volumetric expansion factors have been found useful in correlating heat transfer data over a wide range of operating conditions including liquids, gases and the near critical region.

  12. Generalized data stacking programming model with applications

    Directory of Open Access Journals (Sweden)

    Hala Samir Elhadidy

    2016-09-01

    Full Text Available Recent researches have shown that, everywhere in various sciences the systems are following stacked-based stored change behavior when subjected to events or varying environments “on and above” their normal situations. This paper presents a generalized data stack programming (GDSP model which is developed to describe the system changes under varying environment. These changes which are captured with different ways such as sensor reading are stored in matrices. Extraction algorithm and identification technique are proposed to extract the different layers between images and identify the stack class the object follows; respectively. The general multi-stacking network is presented including the interaction between various stack-based layering of some applications. The experiments prove that the concept of stack matrix gives average accuracy of 99.45%.

  13. Flexural characteristics of a stack leg

    International Nuclear Information System (INIS)

    Cook, J.

    1979-06-01

    A 30 MV tandem Van de Graaff accelerator is at present under construction at Daresbury Laboratory. The insulating stack of the machine is of modular construction, each module being 860 mm in length. Each live section stack module contains 8 insulating legs mounted between bulkhead rings. The design, fabrication (from glass discs bonded to stainless steel discs using an epoxy film adhesive) and testing of the stack legs is described. (U.K.)

  14. Hydrogen Embrittlement And Stacking-Fault Energies

    Science.gov (United States)

    Parr, R. A.; Johnson, M. H.; Davis, J. H.; Oh, T. K.

    1988-01-01

    Embrittlement in Ni/Cu alloys appears related to stacking-fault porbabilities. Report describes attempt to show a correlation between stacking-fault energy of different Ni/Cu alloys and susceptibility to hydrogen embrittlement. Correlation could lead to more fundamental understanding and method of predicting susceptibility of given Ni/Cu alloy form stacking-fault energies calculated from X-ray diffraction measurements.

  15. FLOWCHART; a computer program for plotting flowcharts

    Science.gov (United States)

    Bender, Bernice

    1982-01-01

    The computer program FLOWCHART can be used to very quickly and easily produce flowcharts of high quality for publication. FLOWCHART centers each element or block of text that it processes on one of a set of (imaginary) vertical lines. It can enclose a text block in a rectangle, circle or other selected figure. It can draw a 'line connecting the midpoint of any side of any figure with the midpoint of any side of any other figure and insert an arrow pointing in the direction of flow. It can write 'yes' or 'no' next to the line joining two figures. FLOWCHART creates flowcharts using some basic plotting subroutine* which permit plots to be generated interactively and inspected on a Tektronix compatible graphics screen or plotted in a deferred mode on a Houston Instruments 42' pen plotter. The size of the plot, character set and character height in inches are inputs to the program. Plots generated using the pen plotter can be up to 42' high--the larger size plots being directly usable as visual aids in a talk. FLOWCHART centers each block of text on an imaginary column line. (The number of columns and column width are specified as input.) The midpoint of the longest line of text within the block is defined to be the center of the block and is placed on the column line. The spacing of individual words within the block is not altered when the block is positioned. The program writes the first block of text in a designated column and continues placing each subsequent block below the previous block in the same column. A block of text may be placed in a different column by specifying the number of the column and an earlier block of text with which the new block is to be aligned. If block zero is given as the earlier block, the new text is placed in the new column continuing down the page below the previous block. Optionally a column and number of inches from the top of the page may be given for positioning the next block of text. The program will normally draw one of five

  16. Stacks of SPS Dipole Magnets

    CERN Multimedia

    1974-01-01

    Stacks of SPS Dipole Magnets ready for installation in the tunnel. The SPS uses a separated function lattice with dipoles for bending and quadrupoles for focusing. The 6.2 m long normal conducting dipoles are of H-type with coils that are bent-up at the ends. There are two types, B1 (total of 360) and B2 (384). Both are for a maximum field of 1.8 Tesla and have the same outer dimensions (450x800 mm2 vxh) but with different gaps (B1: 39x129 mm2, B2: 52x92 mm2) tailored to the beam size. The yoke, made of 1.5 mm thick laminations, consists of an upper and a lower half joined together in the median plane once the coils have been inserted.

  17. California dreaming?[PEM stacks

    Energy Technology Data Exchange (ETDEWEB)

    Crosse, J.

    2002-06-01

    Hyundai's Santa Fe FCEV will be on sale by the end of 2002. Hyundai uses PEM stacks that are manufactured by International Fuel Cells (IFC), a division of United Technologies. Santa Fe is equipped with a 65 kW electric powertrain of Enova systems and Shell's new gasoline reformer called Hydrogen Source. Eugene Jang, Senior Engineer - Fuel Cell and Materials at Hyundai stated that the compressor related losses on IFC system are below 3%. The maximum speed offered by the vehicle is estimated as 123km/hr while the petrol equivalent fuel consumption is quoted between 5.6L/100 km and 4.8L/100 km. Santa Fe is a compact vehicle offering better steering response and a pleasant drive. (author)

  18. Producing 3D Plots in MATLAB

    OpenAIRE

    2005-01-01

    sim tut Simulation Tutorial Interactive Media Element This interactive tutorial reviews using MATLAB to create 3-D plots of the function Z(X,Y). The MATLAB functions covered in this tutorial are: meshgrid, mesh, grid, view, xlabel, ylabel, zlabel, clabel, contour, titleThe interactions involve entering MATLAB instructions and observing the outcomes. Self-check questions are provided to help learners determine their level of understanding of the content presented. EC1010 I...

  19. AvoPlot: An extensible scientific plotting tool based on matplotlib

    Directory of Open Access Journals (Sweden)

    Nial Peters

    2014-02-01

    Full Text Available AvoPlot is a simple-to-use graphical plotting program written in Python and making extensive use of the matplotlib plotting library. It can be found at http://code.google.com/p/avoplot/. In addition to providing a user-friendly interface to the powerful capabilities of the matplotlib library, it also offers users the possibility of extending its functionality by creating plug-ins. These can import specific types of data into the interface and also provide new tools for manipulating them. In this respect, AvoPlot is a convenient platform for researchers to build their own data analysis tools on top of, as well as being a useful standalone program.

  20. Stacking technology for a space constrained microsystem

    DEFF Research Database (Denmark)

    Heschel, Matthias; Kuhmann, Jochen Friedrich; Bouwstra, Siebe

    1998-01-01

    In this paper we present a stacking technology for an integrated packaging of an intelligent transducer which is formed by a micromachined silicon transducer and an integrated circuit chip. Transducer and circuitry are stacked on top of each other with an intermediate chip in between. The bonding...

  1. Vector Fields and Flows on Differentiable Stacks

    DEFF Research Database (Denmark)

    A. Hepworth, Richard

    2009-01-01

    This paper introduces the notions of vector field and flow on a general differentiable stack. Our main theorem states that the flow of a vector field on a compact proper differentiable stack exists and is unique up to a uniquely determined 2-cell. This extends the usual result on the existence...... of vector fields....

  2. 40 CFR 61.44 - Stack sampling.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 8 2010-07-01 2010-07-01 false Stack sampling. 61.44 Section 61.44 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL... Firing § 61.44 Stack sampling. (a) Sources subject to § 61.42(b) shall be continuously sampled, during...

  3. Learning OpenStack networking (Neutron)

    CERN Document Server

    Denton, James

    2014-01-01

    If you are an OpenStack-based cloud operator with experience in OpenStack Compute and nova-network but are new to Neutron networking, then this book is for you. Some networking experience is recommended, and a physical network infrastructure is required to provide connectivity to instances and other network resources configured in the book.

  4. Project W-420 stack monitoring system upgrades

    International Nuclear Information System (INIS)

    CARPENTER, K.E.

    1999-01-01

    This project will execute the design, procurement, construction, startup, and turnover activities for upgrades to the stack monitoring system on selected Tank Waste Remediation System (TWRS) ventilation systems. In this plan, the technical, schedule, and cost baselines are identified, and the roles and responsibilities of project participants are defined for managing the Stack Monitoring System Upgrades, Project W-420

  5. On the "stacking fault" in copper

    NARCIS (Netherlands)

    Fransens, J.R.; Pleiter, F

    2003-01-01

    The results of a perturbed gamma-gamma angular correlations experiment on In-111 implanted into a properly cut single crystal of copper show that the defect known in the literature as "stacking fault" is not a planar faulted loop but a stacking fault tetrahedron with a size of 10-50 Angstrom.

  6. Status of MCFC stack technology at IHI

    Energy Technology Data Exchange (ETDEWEB)

    Hosaka, M.; Morita, T.; Matsuyama, T.; Otsubo, M. [Ishikawajima-Harima Heavy Industries Co., Ltd., Tokyo (Japan)

    1996-12-31

    The molten carbonate fuel cell (MCFC) is a promising option for highly efficient power generation possible to enlarge. IHI has been studying parallel flow MCFC stacks with internal manifolds that have a large electrode area of 1m{sup 2}. IHI will make two 250 kW stacks for MW plant, and has begun to make cell components for the plant. To improve the stability of stack, soft corrugated plate used in the separator has been developed, and a way of gathering current from stacks has been studied. The DC output potential of the plant being very high, the design of electric insulation will be very important. A 20 kW short stack test was conducted in 1995 FY to certificate some of the improvements and components of the MW plant. These activities are presented below.

  7. The impact of stack geometry and mean pressure on cold end temperature of stack in thermoacoustic refrigeration systems

    Science.gov (United States)

    Wantha, Channarong

    2018-02-01

    This paper reports on the experimental and simulation studies of the influence of stack geometries and different mean pressures on the cold end temperature of the stack in the thermoacoustic refrigeration system. The stack geometry was tested, including spiral stack, circular pore stack and pin array stack. The results of this study show that the mean pressure of the gas in the system has a significant impact on the cold end temperature of the stack. The mean pressure of the gas in the system corresponds to thermal penetration depth, which results in a better cold end temperature of the stack. The results also show that the cold end temperature of the pin array stack decreases more than that of the spiral stack and circular pore stack geometry by approximately 63% and 70%, respectively. In addition, the thermal area and viscous area of the stack are analyzed to explain the results of such temperatures of thermoacoustic stacks.

  8. From research plots to prototype biomass plantations

    Energy Technology Data Exchange (ETDEWEB)

    Kenney, W.A.; Vanstone, B.J.; Gambles, R.L.; Zsuffa, L. [Univ. of Toronto, Ontario (Canada)

    1993-12-31

    The development of biomass energy plantations is now expanding from the research plot phase into the next level of development at larger scale plantings. This is necessary to provide: more accurate information on biomass yields, realistic production cost figures, venues to test harvesting equipment, demonstration sites for potential producers, and a supply of feedstock for prototype conversion facilities. The paper will discuss some of these objectives and some of the challenges encountered in the scale-up process associated with a willow prototype plantation project currently under development in Eastern Canada.

  9. Single-Event Transgene Product Levels Predict Levels in Genetically Modified Breeding Stacks.

    Science.gov (United States)

    Gampala, Satyalinga Srinivas; Fast, Brandon J; Richey, Kimberly A; Gao, Zhifang; Hill, Ryan; Wulfkuhle, Bryant; Shan, Guomin; Bradfisch, Greg A; Herman, Rod A

    2017-09-13

    The concentration of transgene products (proteins and double-stranded RNA) in genetically modified (GM) crop tissues is measured to support food, feed, and environmental risk assessments. Measurement of transgene product concentrations in breeding stacks of previously assessed and approved GM events is required by many regulatory authorities to evaluate unexpected transgene interactions that might affect expression. Research was conducted to determine how well concentrations of transgene products in single GM events predict levels in breeding stacks composed of these events. The concentrations of transgene products were compared between GM maize, soybean, and cotton breeding stacks (MON-87427 × MON-89034 × DAS-Ø15Ø7-1 × MON-87411 × DAS-59122-7 × DAS-40278-9 corn, DAS-81419-2 × DAS-44406-6 soybean, and DAS-21023-5 × DAS-24236-5 × SYN-IR102-7 × MON-88913-8 × DAS-81910-7 cotton) and their component single events (MON-87427, MON-89034, DAS-Ø15Ø7-1, MON-87411, DAS-59122-7, and DAS-40278-9 corn, DAS-81419-2, and DAS-44406-6 soybean, and DAS-21023-5, DAS-24236-5, SYN-IR102-7, MON-88913-8, and DAS-81910-7 cotton). Comparisons were made within a crop and transgene product across plant tissue types and were also made across transgene products in each breeding stack for grain/seed. Scatter plots were generated comparing expression in the stacks to their component events, and the percent of variability accounted for by the line of identity (y = x) was calculated (coefficient of identity, I 2 ). Results support transgene concentrations in single events predicting similar concentrations in breeding stacks containing the single events. Therefore, food, feed, and environmental risk assessments based on concentrations of transgene products in single GM events are generally applicable to breeding stacks composed of these events.

  10. Density of oxidation-induced stacking faults in damaged silicon

    NARCIS (Netherlands)

    Kuper, F.G.; Hosson, J.Th.M. De; Verwey, J.F.

    1986-01-01

    A model for the relation between density and length of oxidation-induced stacking faults on damaged silicon surfaces is proposed, based on interactions of stacking faults with dislocations and neighboring stacking faults. The model agrees with experiments.

  11. An assessment of air sampling location for stack monitoring in nuclear facility

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jung Bok [University of Science and Technology, Daejeon (Korea, Republic of); Kim, Tae Hyoung; Lee, Jong Il; Kim, Bong Hwan [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2017-06-15

    In this study, air sampling locations in the stack of the Advanced Fuel Science Building (AFSB) at the Korea Atomic Energy Research Institute (KAERI) were assessed according to the ANSI/HPS N13.1-1999 specification. The velocity profile, flow angle and 10 μm aerosol particle profile at the cross-section as functions of stack height L and stack diameter D (L/D) were assessed according to the sampling location criteria using COMSOL. The criteria for the velocity profile were found to be met at 5 L/D or more for the height, and the criteria for the average flow angle were met at all locations through this assessment. The criteria for the particle profile were met at 5 L/D and 9 L/D. However, the particle profile at the cross-section of each sampling location was found to be non-uniform. In order to establish uniformity of the particle profile, a static mixer and a perimeter ring were modeled, after which the degrees of effectiveness of these components were compared. Modeling using the static mixer indicated that the sampling locations that met the criteria for the particle profile were 5-10 L/D. When modeling using the perimeter ring, the sampling locations that met the criteria for particle profile were 5 L/D and 7-10 L/D. The criteria for the velocity profile and the average flow angle were also met at the sampling locations that met the criteria for the particle profile. The methodologies used in this study can also be applied during assessments of air sampling locations when monitoring stacks at new nuclear facilities as well as existing nuclear facilities.

  12. Holey buckets! Monitoring plot-scale runoff

    Science.gov (United States)

    Rupp, D. E.; Stewart, R. D.; Abou Najm, M. R.; Selker, J. S.; Selker, F.; Van De Giesen, N.

    2011-12-01

    Measurement of plot-scale surface runoff is commonly achieved by diverting flow through a flume or tipping bucket system, or into a storage tank, such as bucket. The principle advantages of the "bucket method" are relative simplicity and low cost. The principle drawback is that the bucket requires frequent emptying during heavy runoff, unless the bucket volume is very large. As a solution to the problem of emptying the bucket while still retaining the properties of simplicity and economy, we used a holey bucket. Our "bucket" is vertical 4"-diameter ABS pipe, sealed at the bottom, and with holes along the side of the pipe. A screen in the pipe catches debris that could block the holes. The holes' diameters and locations were chosen to capture both low (100 L min-1) flows. Runoff is diverted into the top of the pipe. The runoff rate is determined from the water level and the rate of change in water level: the water level gives the flow rate out of the submerged holes (using Torricelli's Law) and the change in water level gives the rate of change in storage in the pipe. The runoff is calculated as the sum of the hole discharge and the rate of change in storage. A calibration parameter is applied to account for departures from assumptions of the theory. The design is currently being utilized to monitor runoff from experimental plots on a rural hillslope in Chile.

  13. Tunable electro-optic filter stack

    Energy Technology Data Exchange (ETDEWEB)

    Fontecchio, Adam K.; Shriyan, Sameet K.; Bellingham, Alyssa

    2017-09-05

    A holographic polymer dispersed liquid crystal (HPDLC) tunable filter exhibits switching times of no more than 20 microseconds. The HPDLC tunable filter can be utilized in a variety of applications. An HPDLC tunable filter stack can be utilized in a hyperspectral imaging system capable of spectrally multiplexing hyperspectral imaging data acquired while the hyperspectral imaging system is airborne. HPDLC tunable filter stacks can be utilized in high speed switchable optical shielding systems, for example as a coating for a visor or an aircraft canopy. These HPDLC tunable filter stacks can be fabricated using a spin coating apparatus and associated fabrication methods.

  14. Dynamical stability of slip-stacking particles

    Energy Technology Data Exchange (ETDEWEB)

    Eldred, Jeffrey; Zwaska, Robert

    2014-09-01

    We study the stability of particles in slip-stacking configuration, used to nearly double proton beam intensity at Fermilab. We introduce universal area factors to calculate the available phase space area for any set of beam parameters without individual simulation. We find perturbative solutions for stable particle trajectories. We establish Booster beam quality requirements to achieve 97% slip-stacking efficiency. We show that slip-stacking dynamics directly correspond to the driven pendulum and to the system of two standing-wave traps moving with respect to each other.

  15. Hypothetical Outcome Plots Outperform Error Bars and Violin Plots for Inferences about Reliability of Variable Ordering.

    Science.gov (United States)

    Hullman, Jessica; Resnick, Paul; Adar, Eytan

    2015-01-01

    Many visual depictions of probability distributions, such as error bars, are difficult for users to accurately interpret. We present and study an alternative representation, Hypothetical Outcome Plots (HOPs), that animates a finite set of individual draws. In contrast to the statistical background required to interpret many static representations of distributions, HOPs require relatively little background knowledge to interpret. Instead, HOPs enables viewers to infer properties of the distribution using mental processes like counting and integration. We conducted an experiment comparing HOPs to error bars and violin plots. With HOPs, people made much more accurate judgments about plots of two and three quantities. Accuracy was similar with all three representations for most questions about distributions of a single quantity.

  16. Hypothetical Outcome Plots Outperform Error Bars and Violin Plots for Inferences about Reliability of Variable Ordering.

    Directory of Open Access Journals (Sweden)

    Jessica Hullman

    Full Text Available Many visual depictions of probability distributions, such as error bars, are difficult for users to accurately interpret. We present and study an alternative representation, Hypothetical Outcome Plots (HOPs, that animates a finite set of individual draws. In contrast to the statistical background required to interpret many static representations of distributions, HOPs require relatively little background knowledge to interpret. Instead, HOPs enables viewers to infer properties of the distribution using mental processes like counting and integration. We conducted an experiment comparing HOPs to error bars and violin plots. With HOPs, people made much more accurate judgments about plots of two and three quantities. Accuracy was similar with all three representations for most questions about distributions of a single quantity.

  17. Contour plotting programs for printer and Calcomp plotter

    International Nuclear Information System (INIS)

    Moller, P.

    1980-07-01

    Contour plotting programs for plotting contour diagrams on printers or Calcomp plotters are described. The subroutines also exist in versions that are useful for the special application of finding minima and saddlepoints of nuclear potential energy surfaces generated by the subroutine PETR3 of another program package. For the general user, however, the most interesting aspect of the plotting package is probably the possibility of generating printer contour plots. The plotting of printer contour plots is a very fast and convenient way of displaying two-dimensional functions. 3 figures

  18. Wearable solar cells by stacking textile electrodes.

    Science.gov (United States)

    Pan, Shaowu; Yang, Zhibin; Chen, Peining; Deng, Jue; Li, Houpu; Peng, Huisheng

    2014-06-10

    A new and general method to produce flexible, wearable dye-sensitized solar cell (DSC) textiles by the stacking of two textile electrodes has been developed. A metal-textile electrode that was made from micrometer-sized metal wires was used as a working electrode, while the textile counter electrode was woven from highly aligned carbon nanotube fibers with high mechanical strengths and electrical conductivities. The resulting DSC textile exhibited a high energy conversion efficiency that was well maintained under bending. Compared with the woven DSC textiles that are based on wire-shaped devices, this stacked DSC textile unexpectedly exhibited a unique deformation from a rectangle to a parallelogram, which is highly desired in portable electronics. This lightweight and wearable stacked DSC textile is superior to conventional planar DSCs because the energy conversion efficiency of the stacked DSC textile was independent of the angle of incident light. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. STACKING FAULT ENERGY IN HIGH MANGANESE ALLOYS

    Directory of Open Access Journals (Sweden)

    Eva Mazancová

    2009-04-01

    Full Text Available Stacking fault energy of high manganese alloys (marked as TWIP and TRIPLEX is an important parameter determining deformation mechanism type realized in above mentioned alloys. Stacking fault energy level can be asserted with a gliding of partial and/or full dislocations, b gliding mechanism and twinning deformation process in connection with increasing of fracture deformation level (deformation elongation and with increasing of simultaneously realized work hardening proces., c gliding mechanism and deformation induced e-martensite formation. In contribution calculated stacking fault energies are presented for various chemical compositions of high manganese alloys. Stacking fault energy dependences on manganese, carbon, iron and alluminium contents are presented. Results are confronted with some accessible papers.The aim of work is to deepen knowledge of presented data. The TWIP and TRIPLEX alloys can be held for promissing new automotive materials.

  20. Stack-Based Typed Assembly Language

    National Research Council Canada - National Science Library

    Morrisett, Greg

    1998-01-01

    .... This paper also formalizes the typing connection between CPS based compilation and stack based compilation and illustrates how STAL can formally model calling conventions by specifying them as formal translations of source function types to STAL types.

  1. Characterization of Piezoelectric Stacks for Space Applications

    Science.gov (United States)

    Sherrit, Stewart; Jones, Christopher; Aldrich, Jack; Blodget, Chad; Bao, Xiaoqi; Badescu, Mircea; Bar-Cohen, Yoseph

    2008-01-01

    Future NASA missions are increasingly seeking to actuate mechanisms to precision levels in the nanometer range and below. Co-fired multilayer piezoelectric stacks offer the required actuation precision that is needed for such mechanisms. To obtain performance statistics and determine reliability for extended use, sets of commercial PZT stacks were tested in various AC and DC conditions at both nominal and high temperatures and voltages. In order to study the lifetime performance of these stacks, five actuators were driven sinusoidally for up to ten billion cycles. An automated data acquisition system was developed and implemented to monitor each stack's electrical current and voltage waveforms over the life of the test. As part of the monitoring tests, the displacement, impedance, capacitance and leakage current were measured to assess the operation degradation. This paper presents some of the results of this effort.

  2. The stack on software and sovereignty

    CERN Document Server

    Bratton, Benjamin H

    2016-01-01

    A comprehensive political and design theory of planetary-scale computation proposing that The Stack -- an accidental megastructure -- is both a technological apparatus and a model for a new geopolitical architecture.

  3. Split-plot designs for multistage experimentation

    DEFF Research Database (Denmark)

    Kulahci, Murat; Tyssedal, John

    2016-01-01

    Most of today’s complex systems and processes involve several stages through which input or the raw material has to go before the final product is obtained. Also in many cases factors at different stages interact. Therefore, a holistic approach for experimentation that considers all stages...... on the Kronecker product representation of orthogonal designs and can be used for any number of stages, for various numbers of subplots and for different number of subplots for each stage. The procedure is demonstrated on both regular and nonregular designs and provides the maximum number of factors that can...... be accommodated in each stage. Furthermore, split-plot designs for multistage experiments with good projective properties are also provided....

  4. Tracker Alignment Performance Plots after Commissioning

    CERN Document Server

    CMS Collaboration

    2017-01-01

    During the LHC shutdown in Winter 2016/17, the CMS pixel detector, the inner component of the CMS Tracker, was replaced by the Phase-1 upgrade detector. Among others improvements, the new pixel detector consists of four instead of three layers in the central barrel region (BPIX) and three instead of two disks in the endcap regions (FPIX). In this report, performance plots of pixel detector alignment results are presented, which were obtained with both cosmic-ray and pp collision data acquired at the beginning of the 2017 LHC operation. Alignment constants have been derived for each data-taking period to the level of single module positions in both the pixel and the strip detectors. The complete understanding of the alignment and biases was derived by using two algorithms, Millepede-II and HipPy. The results confirm each other.

  5. Stacking for Cosmic Magnetism with SKA Surveys

    OpenAIRE

    Stil, J. M.; Keller, B. W.

    2015-01-01

    Stacking polarized radio emission in SKA surveys provides statistical information on large samples that is not accessible otherwise due to limitations in sensitivity, source statistics in small fields, and averaging over frequency (including Faraday synthesis). Polarization is a special case because one obvious source of stacking targets is the Stokes I source catalog, possibly in combination with external catalogs, for example an SKA HI survey or a non-radio survey. We point out the signific...

  6. Environmental Modeling Framework using Stacked Gaussian Processes

    OpenAIRE

    Abdelfatah, Kareem; Bao, Junshu; Terejanu, Gabriel

    2016-01-01

    A network of independently trained Gaussian processes (StackedGP) is introduced to obtain predictions of quantities of interest with quantified uncertainties. The main applications of the StackedGP framework are to integrate different datasets through model composition, enhance predictions of quantities of interest through a cascade of intermediate predictions, and to propagate uncertainties through emulated dynamical systems driven by uncertain forcing variables. By using analytical first an...

  7. Generalized data stacking programming model with applications

    OpenAIRE

    Hala Samir Elhadidy; Rawya Yehia Rizk; Hassen Taher Dorrah

    2016-01-01

    Recent researches have shown that, everywhere in various sciences the systems are following stacked-based stored change behavior when subjected to events or varying environments “on and above” their normal situations. This paper presents a generalized data stack programming (GDSP) model which is developed to describe the system changes under varying environment. These changes which are captured with different ways such as sensor reading are stored in matrices. Extraction algorithm and identif...

  8. Representations of stack triangulations in the plane

    OpenAIRE

    Selig, Thomas

    2013-01-01

    Stack triangulations appear as natural objects when defining an increasing family of triangulations by successive additions of vertices. We consider two different probability distributions for such objects. We represent, or "draw" these random stack triangulations in the plane $\\R^2$ and study the asymptotic properties of these drawings, viewed as random compact metric spaces. We also look at the occupation measure of the vertices, and show that for these two distributions it converges to som...

  9. A Time-predictable Stack Cache

    DEFF Research Database (Denmark)

    Abbaspour, Sahar; Brandner, Florian; Schoeberl, Martin

    2013-01-01

    Real-time systems need time-predictable architectures to support static worst-case execution time (WCET) analysis. One architectural feature, the data cache, is hard to analyze when different data areas (e.g., heap allocated and stack allocated data) share the same cache. This sharing leads to le...... of a cache for stack allocated data. Our port of the LLVM C++ compiler supports the management of the stack cache. The combination of stack cache instructions and the hardware implementation of the stack cache is a further step towards timepredictable architectures.......Real-time systems need time-predictable architectures to support static worst-case execution time (WCET) analysis. One architectural feature, the data cache, is hard to analyze when different data areas (e.g., heap allocated and stack allocated data) share the same cache. This sharing leads to less...... precise results of the cache analysis part of the WCET analysis. Splitting the data cache for different data areas enables composable data cache analysis. The WCET analysis tool can analyze the accesses to these different data areas independently. In this paper we present the design and implementation...

  10. Detailed Electrochemical Characterisation of Large SOFC Stacks

    DEFF Research Database (Denmark)

    Mosbæk, Rasmus Rode; Hjelm, Johan; Barfod, R.

    2012-01-01

    As solid oxide fuel cell (SOFC) technology is moving closer to a commercial break through, lifetime limiting factors, determination of the limits of safe operation and methods to measure the “state-of-health” of operating cells and stacks are becoming of increasing interest. This requires applica...... out at a range of ac perturbation amplitudes in order to investigate linearity of the response and the signal-to-noise ratio. Separation of the measured impedance into series and polarisation resistances was possible....... to analyse in detail. Today one is forced to use mathematical modelling to extract information about existing gradients and cell resistances in operating stacks, as mature techniques for local probing are not available. This type of spatially resolved information is essential for model refinement...... and validation, and helps to further the technological stack development. Further, more detailed information obtained from operating stacks is essential for developing appropriate process monitoring and control protocols for stack and system developers. An experimental stack with low ohmic resistance from Topsoe...

  11. Radio-frequency properties of stacked long Josephson junctions with nonuniform bias current distribution

    DEFF Research Database (Denmark)

    Filatrella, G; Pedersen, Niels Falsig

    1999-01-01

    We have numerically investigated the behavior of stacks of long Josephson junctions considering a nonuniform bias profile. In the presence of a microwave field the nonuniform bias, which favors the formation of fluxons, can give rise to a change of the sequence of radio-frequency induced steps...

  12. Heterogeneous Molecular Catalysis of Electrochemical Reactions: Volcano Plots and Catalytic Tafel Plots.

    Science.gov (United States)

    Costentin, Cyrille; Savéant, Jean-Michel

    2017-06-14

    We analyze here, in the framework of heterogeneous molecular catalysis, the reasons for the occurrence or nonoccurrence of volcanoes upon plotting the kinetics of the catalytic reaction versus the stabilization free energy of the primary intermediate of the catalytic process. As in the case of homogeneous molecular catalysis or catalysis by surface-active metallic sites, a strong motivation of such studies relates to modern energy challenges, particularly those involving small molecules, such as water, hydrogen, oxygen, proton, and carbon dioxide. This motivation is particularly pertinent for what concerns heterogeneous molecular catalysis, since it is commonly preferred to homogeneous molecular catalysis by the same molecules if only for chemical separation purposes and electrolytic cell architecture. As with the two other catalysis modes, the main drawback of the volcano plot approach is the basic assumption that the kinetic responses depend on a single descriptor, viz., the stabilization free energy of the primary intermediate. More comprehensive approaches, investigating the responses to the maximal number of experimental factors, and conveniently expressed as catalytic Tafel plots, should clearly be preferred. This is more so in the case of heterogeneous molecular catalysis in that additional transport factors in the supporting film may additionally affect the current-potential responses. This is attested by the noteworthy presence of maxima in catalytic Tafel plots as well as their dependence upon the cyclic voltammetric scan rate.

  13. Variability of Measured Runoff and Soil Loss from Field Plots

    Directory of Open Access Journals (Sweden)

    F. Asadzadeh

    2016-02-01

    Full Text Available Introduction: Field plots are widely used in studies related to the measurements of soil loss and modeling of erosion processes. Research efforts are needed to investigate factors affecting the data quality of plots. Spatial scale or size of plots is one of these factors which directly affects measuring runoff and soil loss by means of field plots. The effect of plot size on measured runoff or soil loss from natural plots is known as plot scale effect. On the other hand, variability of runoff and sediment yield from replicated filed plots is a main source of uncertainty in measurement of erosion from plots which should be considered in plot data interpretation processes. Therefore, there is a demand for knowledge of soil erosion processes occurring in plots of different sizes and of factors that determine natural variability, as a basis for obtaining soil loss data of good quality. This study was carried out to investigate the combined effects of these two factors by measurement of runoff and soil loss from replicated plots with different sizes. Materials and Methods: In order to evaluate the variability of runoff and soil loss data seven plots, differing in width and length, were constructed in a uniform slope of 9% at three replicates at Koohin Research Station in Qazvin province. The plots were ploughed up to down slope in September 2011. Each plot was isolated using soil beds with a height of 30 cm, to direct generated surface runoff to the lower part of the plots. Runoff collecting systems composed of gutters, pipes and tankswere installed at the end of each plot. During the two-year study period of 2011-2012, plots were maintained in bare conditions and runoff and soil loss were measured for each single event. Precipitation amounts and characteristics were directly measured by an automatic recording tipping-bucket rain gauge located about 200 m from the experimental plots. The entire runoff volume including eroded sediment was measured on

  14. A Force Sensorless Method for CFRP/Ti Stack Interface Detection during Robotic Orbital Drilling Operations

    Directory of Open Access Journals (Sweden)

    Qiang Fang

    2015-01-01

    Full Text Available Drilling carbon fiber reinforced plastics and titanium (CFRP/Ti stacks is one of the most important activities in aircraft assembly. It is favorable to use different drilling parameters for each layer due to their dissimilar machining properties. However, large aircraft parts with changing profiles lead to variation of thickness along the profiles, which makes it challenging to adapt the cutting parameters for different materials being drilled. This paper proposes a force sensorless method based on cutting force observer for monitoring the thrust force and identifying the drilling material during the drilling process. The cutting force observer, which is the combination of an adaptive disturbance observer and friction force model, is used to estimate the thrust force. An in-process algorithm is developed to monitor the variation of the thrust force for detecting the stack interface between the CFRP and titanium materials. Robotic orbital drilling experiments have been conducted on CFRP/Ti stacks. The estimate error of the cutting force observer was less than 13%, and the stack interface was detected in 0.25 s (or 0.05 mm before or after the tool transited it. The results show that the proposed method can successfully detect the CFRP/Ti stack interface for the cutting parameters adaptation.

  15. 33 CFR 164.38 - Automatic radar plotting aids (ARPA).

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Automatic radar plotting aids... plotting aids (ARPA). (a) The following definitions are used in this section— Bulk means material in any... Radar Plotting Aids” (Appendix A), and that has both audible and visual alarms, must be installed as...

  16. From Multi to Single Stack Automata

    Science.gov (United States)

    Atig, Mohamed Faouzi

    We investigate the issue of reducing the verification problem of multi-stack machines to the one for single-stack machines. For instance, elegant (and practically efficient) algorithms for bounded-context switch analysis of multi-pushdown systems have been recently defined based on reductions to the reachability problem of (single-stack) pushdown systems [10,18]. In this paper, we extend this view to both bounded-phase visibly pushdown automata (BVMPA) [16] and ordered multi-pushdown automata (OMPA) [1] by showing that each of their emptiness problem can be reduced to the one for a class of single-stack machines. For these reductions, we introduce effective generalized pushdown automata (EGPA) where operations on stacks are (1) pop the top symbol of the stack, and (2) push a word in some (effectively) given set of words L over the stack alphabet, assuming that L is in some class of languages for which checking whether L intersects regular languages is decidable. We show that the automata-based saturation procedure for computing the set of predecessors in standard pushdown automata can be extended to prove that for EGPA too the set of all predecessors of a regular set of configurations is an effectively constructible regular set. Our reductions from OMPA and BVMPA to EGPA, together with the reachability analysis procedure for EGPA, allow to provide conceptually simple algorithms for checking the emptiness problem for each of these models, and to significantly simplify the proofs for their 2ETIME upper bounds (matching their lower-bounds).

  17. Start-Stop Test Procedures on the PEMFC Stack Level

    DEFF Research Database (Denmark)

    Mitzel, Jens; Nygaard, Frederik; Veltzé, Sune

    The test is addressed to investigate the influence on stack durability of a long stop followed by a restart of a stack. Long stop should be defined as a stop in which the anodic compartment is fully filled by air due to stack leakages. In systems, leakage level of the stack is low and time to fil...

  18. AN EXPERIMENTAL ASSESSMENT OF THE PLATE HEAT EXCHANGER CHARACTERISTICS BY WILSON PLOT METHOD

    Directory of Open Access Journals (Sweden)

    Jan Opatřil

    2016-10-01

    Full Text Available An aim of this paper is suggestion of the evaluation method based on the experimental data and the Wilson plot method for the Plate Heat Exchangers (PHE. For the purpose of the project the new experimental loop was built for the testing of PHE to obtain the overhaul heat transfer coefficient and pressure drop between inlet and outlet of the fluid. The measurement were done for three different PHE with the performance range 30-100kW. The working fluid was water on both sides of the PHE. The differences are in number of pates as well as in extrusion profiles. The Wilson plot evaluation method was involved for the processing experimental data. To obtain more accurate correlations between the experimental data and theoretical results yield of the Wilson plot, the method was enhanced by the measured pressure drop involving. This approach could be useful for PHE designing software and for the manufacturing company.

  19. EmuStack: An OpenStack-Based DTN Network Emulation Platform (Extended Version

    Directory of Open Access Journals (Sweden)

    Haifeng Li

    2016-01-01

    Full Text Available With the advancement of computing and network virtualization technology, the networking research community shows great interest in network emulation. Compared with network simulation, network emulation can provide more relevant and comprehensive details. In this paper, EmuStack, a large-scale real-time emulation platform for Delay Tolerant Network (DTN, is proposed. EmuStack aims at empowering network emulation to become as simple as network simulation. Based on OpenStack, distributed synchronous emulation modules are developed to enable EmuStack to implement synchronous and dynamic, precise, and real-time network emulation. Meanwhile, the lightweight approach of using Docker container technology and network namespaces allows EmuStack to support a (up to hundreds of nodes large-scale topology with only several physical nodes. In addition, EmuStack integrates the Linux Traffic Control (TC tools with OpenStack for managing and emulating the virtual link characteristics which include variable bandwidth, delay, loss, jitter, reordering, and duplication. Finally, experiences with our initial implementation suggest the ability to run and debug experimental network protocol in real time. EmuStack environment would bring qualitative change in network research works.

  20. Levitation characteristics of HTS tape stacks

    Energy Technology Data Exchange (ETDEWEB)

    Pokrovskiy, S. V.; Ermolaev, Y. S.; Rudnev, I. A. [National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), Moscow (Russian Federation)

    2015-03-15

    Due to the considerable development of the technology of second generation high-temperature superconductors and a significant improvement in their mechanical and transport properties in the last few years it is possible to use HTS tapes in the magnetic levitation systems. The advantages of tapes on a metal substrate as compared with bulk YBCO material primarily in the strength, and the possibility of optimizing the convenience of manufacturing elements of levitation systems. In the present report presents the results of the magnetic levitation force measurements between the stack of HTS tapes containing of tapes and NdFeB permanent magnet in the FC and ZFC regimes. It was found a non- linear dependence of the levitation force from the height of the array of stack in both modes: linear growth at small thickness gives way to flattening and constant at large number of tapes in the stack. Established that the levitation force of stacks comparable to that of bulk samples. The numerical calculations using finite element method showed that without the screening of the applied field the levitation force of the bulk superconductor and the layered superconductor stack with a critical current of tapes increased by the filling factor is exactly the same, and taking into account the screening force slightly different.

  1. Forced Air-Breathing PEMFC Stacks

    Directory of Open Access Journals (Sweden)

    K. S. Dhathathreyan

    2012-01-01

    Full Text Available Air-breathing fuel cells have a great potential as power sources for various electronic devices. They differ from conventional fuel cells in which the cells take up oxygen from ambient air by active or passive methods. The air flow occurs through the channels due to concentration and temperature gradient between the cell and the ambient conditions. However developing a stack is very difficult as the individual cell performance may not be uniform. In order to make such a system more realistic, an open-cathode forced air-breathing stacks were developed by making appropriate channel dimensions for the air flow for uniform performance in a stack. At CFCT-ARCI (Centre for Fuel Cell Technology-ARC International we have developed forced air-breathing fuel cell stacks with varying capacity ranging from 50 watts to 1500 watts. The performance of the stack was analysed based on the air flow, humidity, stability, and so forth, The major advantage of the system is the reduced number of bipolar plates and thereby reduction in volume and weight. However, the thermal management is a challenge due to the non-availability of sufficient air flow to remove the heat from the system during continuous operation. These results will be discussed in this paper.

  2. Contemporary sample stacking in analytical electrophoresis.

    Science.gov (United States)

    Malá, Zdena; Šlampová, Andrea; Křivánková, Ludmila; Gebauer, Petr; Boček, Petr

    2015-01-01

    This contribution is a methodological review of the publications about the topic from the last 2 years. Therefore, it is primarily organized according to the methods and procedures used in surveyed papers and the origin and type of sample and specification of analytes form the secondary structure. The introductory part about navigation in the architecture of stacking brings a brief characterization of the various stacking methods, with the description of mutual links to each other and important differences among them. The main body of the article brings a survey of publications organized according to main principles of stacking and then according to the origin and type of the sample. Provided that the paper cited gave explicitly the relevant data, information about the BGE(s) used, procedure, detector employed, and reached LOD and/or concentration effect is given. The papers where the procedure used is a combination of diverse fragments and parts of various stacking techniques are mentioned in a special section on combined techniques. The concluding remarks in the final part of the review evaluate present state of art and the trends of sample stacking in CE. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  3. Enhanced dynamical stability with harmonic slip stacking

    Directory of Open Access Journals (Sweden)

    Jeffrey Eldred

    2016-10-01

    Full Text Available We develop a configuration of radio-frequency (rf cavities to dramatically improve the performance of slip stacking. Slip stacking is an accumulation technique used at Fermilab to nearly double proton intensity by maintaining two beams of different momenta in the same storage ring. The two particle beams are longitudinally focused in the Recycler by two 53 MHz 100 kV rf cavities with a small frequency difference between them. We propose an additional 106 MHz 20 kV rf cavity with a frequency at the double the average of the upper and lower main rf frequencies. We show the harmonic rf cavity cancels out the resonances generated between the two main rf cavities and we derive the relationship between the harmonic rf voltage and the main rf voltage. We find the area factors that can be used to calculate the available phase space area for any set of beam parameters without individual simulation. We establish Booster beam quality requirements to achieve 99% slip stacking efficiency. We measure the longitudinal distribution of the Booster beam and use it to generate a realistic beam model for slip stacking simulation. We demonstrate that the harmonic rf cavity can not only reduce particle loss during slip stacking, but also reduce the final longitudinal emittance.

  4. Accelerated testing of solid oxide fuel cell stacks for micro combined heat and power application

    DEFF Research Database (Denmark)

    Hagen, Anke; Høgh, Jens Valdemar Thorvald; Barfod, Rasmus

    2015-01-01

    of degradation, the profiles are executed faster than required for real applications. Operation with fast load cycling, both using hydrogen and methane/steam as fuels, does not accelerate degradation compared to constant operation, which demonstrates the maturity of SoA stacks and enables transferring knowledge...... from testing at constant conditions to dynamic operation. 7.5 times more cycles than required for 80,000 h lifetime as micro CHP are achieved on one-cell-stack level. The results also suggest that degradation mechanisms that proceed on a longer time-scale, such as creep, might have a more dominating...

  5. iCanPlot: visual exploration of high-throughput omics data using interactive Canvas plotting.

    Directory of Open Access Journals (Sweden)

    Amit U Sinha

    Full Text Available Increasing use of high throughput genomic scale assays requires effective visualization and analysis techniques to facilitate data interpretation. Moreover, existing tools often require programming skills, which discourages bench scientists from examining their own data. We have created iCanPlot, a compelling platform for visual data exploration based on the latest technologies. Using the recently adopted HTML5 Canvas element, we have developed a highly interactive tool to visualize tabular data and identify interesting patterns in an intuitive fashion without the need of any specialized computing skills. A module for geneset overlap analysis has been implemented on the Google App Engine platform: when the user selects a region of interest in the plot, the genes in the region are analyzed on the fly. The visualization and analysis are amalgamated for a seamless experience. Further, users can easily upload their data for analysis--which also makes it simple to share the analysis with collaborators. We illustrate the power of iCanPlot by showing an example of how it can be used to interpret histone modifications in the context of gene expression.

  6. iCanPlot: visual exploration of high-throughput omics data using interactive Canvas plotting.

    Science.gov (United States)

    Sinha, Amit U; Armstrong, Scott A

    2012-01-01

    Increasing use of high throughput genomic scale assays requires effective visualization and analysis techniques to facilitate data interpretation. Moreover, existing tools often require programming skills, which discourages bench scientists from examining their own data. We have created iCanPlot, a compelling platform for visual data exploration based on the latest technologies. Using the recently adopted HTML5 Canvas element, we have developed a highly interactive tool to visualize tabular data and identify interesting patterns in an intuitive fashion without the need of any specialized computing skills. A module for geneset overlap analysis has been implemented on the Google App Engine platform: when the user selects a region of interest in the plot, the genes in the region are analyzed on the fly. The visualization and analysis are amalgamated for a seamless experience. Further, users can easily upload their data for analysis--which also makes it simple to share the analysis with collaborators. We illustrate the power of iCanPlot by showing an example of how it can be used to interpret histone modifications in the context of gene expression.

  7. Investigating stacking faults in nonpolar gallium nitride films using X-ray diffraction

    International Nuclear Information System (INIS)

    Moram, M.A.; Johnston, C.F.; Kappers, M.J.; Humphreys, C.J.

    2009-01-01

    Nonpolar (11-20) GaN films with different basal-plane stacking fault (BSF) densities (determined using transmission electron microscopy) were investigated using X-ray diffraction. Diffuse streaking from I 1 and I 2 BSFs was observed in reciprocal space maps of the 10-10 and 20-20 reflections. X-ray calibration curves for BSF density determination can be plotted using the diffusely scattered intensity of open detector 10-10 or 20-20 ω-scans measured at a fixed, large separation from the peak maximum. However, ab initio determination of stacking fault densities is not possible due to additional broadening from other defects. Similarly, ω-scan peak widths are poor indicators of BSF densities.

  8. Progress of MCFC stack technology at Toshiba

    Energy Technology Data Exchange (ETDEWEB)

    Hori, M.; Hayashi, T.; Shimizu, Y. [Toshiba Corp., Tokyo (Japan)

    1996-12-31

    Toshiba is working on the development of MCFC stack technology; improvement of cell characteristics, and establishment of separator technology. For the cell technology, Toshiba has concentrated on both the restraints of NiO cathode dissolution and electrolyte loss from cells, which are the critical issues to extend cell life in MCFC, and great progress has been made. On the other hand, recognizing that the separator is one of key elements in accomplishing reliable and cost-competitive MCFC stacks, Toshiba has been accelerating the technology establishment and verification of an advanced type separator. A sub-scale stack with such a separator was provided for an electric generating test, and has been operated for more than 10,000 hours. This paper presents several topics obtained through the technical activities in the MCFC field at Toshiba.

  9. Design Handbook for a Stack Foundation

    OpenAIRE

    Tuominen, Vilma

    2011-01-01

    This thesis was made for Citec Engineering Oy Ab as a handbook and as a design tool for concrete structure designers. Handbook is about the Wärtsilä Power Plant stack structure, which is a base for about 40 meters high stack pipe. The purpose is to make a calculation base to support the design work, which helps the designer to check the right dimensions of the structure. Thesis is about to be for the concrete designers and also other designers and authorities. As an example I have used an...

  10. Simple model of stacking-fault energies

    DEFF Research Database (Denmark)

    Stokbro, Kurt; Jacobsen, Lærke Wedel

    1993-01-01

    A simple model for the energetics of stacking faults in fcc metals is constructed. The model contains third-nearest-neighbor pairwise interactions and a term involving the fourth moment of the electronic density of states. The model is in excellent agreement with recently published local-density ......A simple model for the energetics of stacking faults in fcc metals is constructed. The model contains third-nearest-neighbor pairwise interactions and a term involving the fourth moment of the electronic density of states. The model is in excellent agreement with recently published local...

  11. The rainfall plot: its motivation, characteristics and pitfalls.

    Science.gov (United States)

    Domanska, Diana; Vodák, Daniel; Lund-Andersen, Christin; Salvatore, Stefania; Hovig, Eivind; Sandve, Geir Kjetil

    2017-05-18

    A visualization referred to as rainfall plot has recently gained popularity in genome data analysis. The plot is mostly used for illustrating the distribution of somatic cancer mutations along a reference genome, typically aiming to identify mutation hotspots. In general terms, the rainfall plot can be seen as a scatter plot showing the location of events on the x-axis versus the distance between consecutive events on the y-axis. Despite its frequent use, the motivation for applying this particular visualization and the appropriateness of its usage have never been critically addressed in detail. We show that the rainfall plot allows visual detection even for events occurring at high frequency over very short distances. In addition, event clustering at multiple scales may be detected as distinct horizontal bands in rainfall plots. At the same time, due to the limited size of standard figures, rainfall plots might suffer from inability to distinguish overlapping events, especially when multiple datasets are plotted in the same figure. We demonstrate the consequences of plot congestion, which results in obscured visual data interpretations. This work provides the first comprehensive survey of the characteristics and proper usage of rainfall plots. We find that the rainfall plot is able to convey a large amount of information without any need for parameterization or tuning. However, we also demonstrate how plot congestion and the use of a logarithmic y-axis may result in obscured visual data interpretations. To aid the productive utilization of rainfall plots, we demonstrate their characteristics and potential pitfalls using both simulated and real data, and provide a set of practical guidelines for their proper interpretation and usage.

  12. Effects of Endwall Geometry and Stacking on Two-Stage Supersonic Turbine Performance

    Science.gov (United States)

    Dorney, Daniel J.; Griffin, Lisa W.; Huber, Frank W.; Sondak, Douglas L.; Turner, Jim (Technical Monitor)

    2002-01-01

    The drive towards high-work turbines has led to designs which can be compact, transonic, supersonic, counter rotating, or use a dense drive gas. These aggressive designs can lead to strong secondary flows and airfoil flow separation. In many cases the secondary and separated flows can be minimized by contouring the hub/shroud endwalls and/or modifying the airfoil stacking. In this study, three-dimensional unsteady Navier-Stokes simulations were performed to study three different endwall shapes between the first-stage vanes and rotors, as well as two different stackings for the first-stage vanes. The predicted results indicate that changing the stacking of the first-stage vanes can significantly impact endwall separation (and turbine performance) in regions where the endwall profile changes.

  13. Quantifying the risk of error when interpreting funnel plots.

    Science.gov (United States)

    Simmonds, Mark

    2015-03-11

    Funnel plots are widely used to investigate possible publication bias in meta-analyses. There has, however, been little formal assessment of whether a visual inspection of a funnel plot is sufficient to identify publication bias. Visual assessment of bias in a funnel plot is quantified using two new statistics: the Imbalance and the Asymmetry Distance, both intended to replicate how a funnel plot is typically assessed. A simulation study was performed to assess the performance of these two statistics for identifying publication bias. The two statistics both have high type I error and low statistical power, unless the number of studies in the meta-analysis is very large. These results suggest that visual inspection of a funnel plot is unlikely to lead to a valid assessment of publication bias. In most systematic reviews, visual inspection of a funnel plot may give a misleading impression of the presence or absence of publication bias. Formal statistical tests for bias should generally be preferred.

  14. FLOWPLOT: a fluid dynamics and heat transfer plotting package

    International Nuclear Information System (INIS)

    Elrod, D.C.; Tunstall, J.N.

    1978-03-01

    The FLOWPLOT plotting program may be used with numerical fluid dynamics (or heat transfer with convection) codes to create velocity vector plots and/or contour plots of up to three fluid parameters (e.g. pressure, density, and temperature). FLOWPLOT reads a data set created by the user's fluid dynamics code. This data set must contain parametric data at every nodal point of a rectangular grid. FLOWPLOT uses the Display Integrated Software System and Plotting Language (DISSPLA). Therefore, the user has the option of creating the plot data set on CALCOMP tape or creating a compressed plot data set that may be input to the DISSPLA postprocessor. This program has been stored on disk at ORGDP on the IBM 360/370 computing system

  15. Coarse-graining time series data: Recurrence plot of recurrence plots and its application for music

    Science.gov (United States)

    Fukino, Miwa; Hirata, Yoshito; Aihara, Kazuyuki

    2016-02-01

    We propose a nonlinear time series method for characterizing two layers of regularity simultaneously. The key of the method is using the recurrence plots hierarchically, which allows us to preserve the underlying regularities behind the original time series. We demonstrate the proposed method with musical data. The proposed method enables us to visualize both the local and the global musical regularities or two different features at the same time. Furthermore, the determinism scores imply that the proposed method may be useful for analyzing emotional response to the music.

  16. Privatization of Land Plot Under Integral Real Estate Complex

    Directory of Open Access Journals (Sweden)

    Maruchek A. A.

    2014-10-01

    Full Text Available The article deals with the questions concerning the privatization of a land plot under integral real estate complex. The authors come to conclusion that a number of legislation norms relating to privatization of a land plot do not take into account the construction of an integral real estate complex that could cause some problems in the realization of the right to privatization of the land plot

  17. Split-Plot Designs with Mirror Image Pairs as Subplots

    DEFF Research Database (Denmark)

    Tyssedal, John; Kulahci, Murat; Bisgaard, Soren

    2011-01-01

    In this article we investigate two-level split-plot designs where the sub-plots consist of only two mirror image trials. Assuming third and higher order interactions negligible, we show that these designs divide the estimated effects into two orthogonal sub-spaces, separating sub-plot main effects...... appealing with effects of major interest free from full aliasing assuming that 3rd and higher order interactions are negligible....

  18. Contemporary sample stacking in analytical electrophoresis

    Czech Academy of Sciences Publication Activity Database

    Šlampová, Andrea; Malá, Zdeňka; Pantůčková, Pavla; Gebauer, Petr; Boček, Petr

    2013-01-01

    Roč. 34, č. 1 (2013), s. 3-18 ISSN 0173-0835 R&D Projects: GA ČR GAP206/10/1219 Institutional support: RVO:68081715 Keywords : biological samples * stacking * trace analysis * zone electrophoresis Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 3.161, year: 2013

  19. SRS reactor stack plume marking tests

    International Nuclear Information System (INIS)

    Petry, S.F.

    1992-03-01

    Tests performed in 105-K in 1987 and 1988 demonstrated that the stack plume can successfully be made visible (i.e., marked) by introducing smoke into the stack breech. The ultimate objective of these tests is to provide a means during an emergency evacuation so that an evacuee can readily identify the stack plume and evacuate in the opposite direction, thus minimizing the potential of severe radiation exposure. The EPA has also requested DOE to arrange for more tests to settle a technical question involving the correct calculation of stack downwash. New test canisters were received in 1988 designed to produce more smoke per unit time; however, these canisters have not been evaluated, because normal ventilation conditions have not been reestablished in K Area. Meanwhile, both the authorization and procedure to conduct the tests have expired. The tests can be performed during normal reactor operation. It is recommended that appropriate authorization and procedure approval be obtained to resume testing after K Area restart

  20. Testing of Electrodes, Cells and Short Stacks

    DEFF Research Database (Denmark)

    Hauch, Anne; Mogensen, Mogens Bjerg

    2017-01-01

    The present contribution describes the electrochemical testing and characterization of electrodes, cells, and short stacks. To achieve the maximum insight and results from testing of electrodes and cells, it is obviously necessary to have a good understanding of the fundamental principles...

  1. Stack Gas Scrubber Makes the Grade

    Science.gov (United States)

    Chemical and Engineering News, 1975

    1975-01-01

    Describes a year long test of successful sulfur dioxide removal from stack gas with a calcium oxide slurry. Sludge disposal problems are discussed. Cost is estimated at 0.6 mill per kwh not including sludge removal. A flow diagram and equations are included. (GH)

  2. OpenStack Object Storage (Swift) essentials

    CERN Document Server

    Kapadia, Amar; Varma, Sreedhar

    2015-01-01

    If you are an IT administrator and you want to enter the world of cloud storage using OpenStack Swift, then this book is ideal for you. Basic knowledge of Linux and server technology is beneficial to get the most out of the book.

  3. Stacked spheres and lower bound theorem

    Indian Academy of Sciences (India)

    BASUDEB DATTA

    2011-11-20

    Nov 20, 2011 ... Preliminaries. Lower bound theorem. On going work. Definitions. An n-simplex is a convex hull of n + 1 affinely independent points. (called vertices) in some Euclidean space R. N . Stacked spheres and lower bound theorem. Basudeb Datta. Indian Institute of Science. 2 / 27 ...

  4. Contemporary sample stacking in analytical electrophoresis

    Czech Academy of Sciences Publication Activity Database

    Malá, Zdeňka; Šlampová, Andrea; Křivánková, Ludmila; Gebauer, Petr; Boček, Petr

    2015-01-01

    Roč. 36, č. 1 (2015), s. 15-35 ISSN 0173-0835 R&D Projects: GA ČR(CZ) GA13-05762S Institutional support: RVO:68081715 Keywords : biological samples * stacking * trace analysis * zone electrophoresis Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 2.482, year: 2015

  5. The data type variety of stack algebras

    NARCIS (Netherlands)

    Bergstra, J.A.; Tucker, J.V.

    1995-01-01

    We define and study the class of all stack algebras as the class of all minimal algebras in a variety defined by an infinite recursively enumerable set of equations. Among a number of results, we show that the initial model of the variety is computable, that its equational theory is decidable,

  6. Photoswitchable Intramolecular H-Stacking of Perylenebisimide

    NARCIS (Netherlands)

    Wang, Jiaobing; Kulago, Artem; Browne, Wesley R.; Feringa, Ben L.

    2010-01-01

    Dynamic control over the formation of H- or J-type aggregates of chromophores is of fundamental importance for developing responsive organic optoelectronic materials. In this study, the first example of photoswitching between a nonstacked and an intramolecularly H-stacked arrangement of

  7. 40 CFR 61.53 - Stack sampling.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 8 2010-07-01 2010-07-01 false Stack sampling. 61.53 Section 61.53 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL... sampling. (a) Mercury ore processing facility. (1) Unless a waiver of emission testing is obtained under...

  8. 40 CFR 61.33 - Stack sampling.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 8 2010-07-01 2010-07-01 false Stack sampling. 61.33 Section 61.33 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL... sampling. (a) Unless a waiver of emission testing is obtained under § 61.13, each owner or operator...

  9. OpenStack cloud computing cookbook

    CERN Document Server

    Jackson, Kevin

    2013-01-01

    A Cookbook full of practical and applicable recipes that will enable you to use the full capabilities of OpenStack like never before.This book is aimed at system administrators and technical architects moving from a virtualized environment to cloud environments with familiarity of cloud computing platforms. Knowledge of virtualization and managing linux environments is expected.

  10. High power multiple wavelength diode laser stack for DPSSL application without temperature control

    Science.gov (United States)

    Hou, Dong; Yin, Xia; Wang, Jingwei; Chen, Shi; Zhan, Yun; Li, Xiaoning; Fan, Yingmin; Liu, Xingsheng

    2018-02-01

    High power diode laser stack is widely used in pumping solid-state laser for years. Normally an integrated temperature control module is required for stabilizing the output power of solid-state laser, as the output power of the solid-state laser highly depends on the emission wavelength and the wavelength shift of diode lasers according to the temperature changes. However the temperature control module is inconvenient for this application, due to its large dimension, high electric power consumption and extra adding a complicated controlling system. Furthermore, it takes dozens of seconds to stabilize the output power when the laser system is turned on. In this work, a compact hard soldered high power conduction cooled diode laser stack with multiple wavelengths is developed for stabilizing the output power of solid-state laser in a certain temperature range. The stack consists of 5 laser bars with the pitch of 0.43mm. The peak output power of each bar in the diode laser stack reaches as much as 557W and the combined lasing wavelength spectrum profile spans 15nm. The solidstate laser, structured with multiple wavelength diode laser stacks, allows the ambient temperature change of 65°C without suddenly degrading the optical performance.

  11. Studies on complex π-π and T-stacking features of imidazole and phenyl/p-halophenyl units in series of 5-amino-1-(phenyl/p-halophenyl)imidazole-4-carboxamides and their carbonitrile derivatives: Role of halogens in tuning of conformation

    Science.gov (United States)

    Das, Aniruddha

    2017-11-01

    5-amino-1-(phenyl/p-halophenyl)imidazole-4-carboxamides (N-phenyl AICA) (2a-e) and 5-amino-1-(phenyl/p-halophenyl)imidazole-4-carbonitriles (N-phenyl AICN) (3a-e) had been synthesized. X-ray crystallographic studies of 2a-e and 3a-e had been performed to identify any distinct change in stacking patterns in their crystal lattice. Single crystal X-ray diffraction studies of 2a-e revealed π-π stack formations with both imidazole and phenyl/p-halophenyl units in anti and syn parallel-displaced (PD)-type dispositions. No π-π stacking of imidazole occurred when the halogen substituent is bromo or iodo; π-π stacking in these cases occurred involving phenyl rings only. The presence of an additional T-stacking had been observed in crystal lattices of 3a-e. Vertical π-π stacking distances in anti-parallel PD-type arrangements as well as T-stacking distances had shown stacking distances short enough to impart stabilization whereas syn-parallel stacking arrangements had got much larger π-π stacking distances to belie any syn-parallel stacking stabilization. DFT studies had been pursued for quantifying the π-π stacking and T-stacking stabilization. The plotted curves for anti-parallel and T-stacked moieties had similarities to the 'Morse potential energy curve for diatomic molecule'. The minima of the curves corresponded to the most stable stacking distances and related energy values indicated stacking stabilization. Similar DFT studies on syn-parallel systems of 2b corresponded to no π-π stacking stabilization at all. Halogen-halogen interactions had also been observed to stabilize the compounds 2d, 2e and 3d. Nano-structural behaviour of the series of compounds 2a-e and 3a-e were thoroughly investigated.

  12. Time contour expression of limited range phenomena on stack chart; Jugo chart jo deno kyokuchi gensho jikan contour

    Energy Technology Data Exchange (ETDEWEB)

    Kametani, T.

    1997-05-27

    Time contour expression of limited range phenomena on stack chart is examined for further improvement on the result of the ultimate interpretation in the seismic reflection survey. The policy is made clear from the beginning that local phenomena are to be discussed, and data prior CMP stacking is interpreted in detail. For this purpose, it is effective to make use of the time contour expression in the midpoint-offset plane simultaneously with the CMP and COP panels. For the review of data prior to CMP stacking, it is convenient to use the CMP (CDP) stacking chart in which the data is arranged methodically. In this chart, all the channels which are crude data prior to stacking are plotted on midpoint-offset coordinates, which plane is called the MOD (Midpoint Offset Domain) panel. Various panels can be chosen unrestrictedly, and their mutual relations can be easily grasped. When data points are given a time axis, they can be expressed in a time contour. Studies are conducted about the underground structure, multiple reflection paths divided by it, and characteristics of detour reflection attributable to faults. 4 refs., 9 figs.

  13. Project W-420 Stack Monitoring system upgrades conceptual design report

    Energy Technology Data Exchange (ETDEWEB)

    TUCK, J.A.

    1998-11-06

    This document describes the scope, justification, conceptual design, and performance of Project W-420 stack monitoring system upgrades on six NESHAP-designated, Hanford Tank Farms ventilation exhaust stacks.

  14. Heuristic Solution Approaches to the Double TSP with Multiple Stacks

    DEFF Research Database (Denmark)

    Petersen, Hanne Løhmann

    This paper introduces the Double Travelling Salesman Problem with Multiple Stacks and presents a three different metaheuristic approaches to its solution. The Double Travelling Salesman Problem with Multiple Stacks is concerned with finding the shortest route performing pickups and deliveries...

  15. Heuristic Solution Approaches to the Double TSP with Multiple Stacks

    DEFF Research Database (Denmark)

    Petersen, Hanne Løhmann

    2006-01-01

    This paper introduces the Double Travelling Salesman Problem with Multiple Stacks and presents a three different metaheuristic approaches to its solution. The Double Travelling Salesman Problem with Multiple Stacks is concerned with finding the shortest route performing pickups and deliveries...

  16. Funnel plots and their emerging application in surgery.

    Science.gov (United States)

    Mayer, Erik K; Bottle, Alex; Rao, Christopher; Darzi, Ara W; Athanasiou, Thanos

    2009-03-01

    To familiarize surgeons with the use of funnel plots as a control tool to assess quality in surgery. Surgical outcomes are an important component of quality in healthcare delivery. Several control tools have been introduced and tested including the use of graphical tools such as funnel plots. More recently, their application in healthcare to assess quality has become more evident. Ranking in surgical performance has significant limitations, risks, and implications which can be addressed by the use of funnel plots. This methodological review explores the principles and existing application of funnel plots within surgery and emphasizes their advantages, limitations, public health implications, and their use to assess the evidence in the literature and potential future applications. Funnel plots are practical tools, easy to use, and offer the opportunity to statistically define control limits around measurable outcomes, allowing for adjustment of unmeasured factors. This makes them extremely useful for the monitoring of performance in surgery either at a surgeon, institutional, regional, or national level, by means of qualifying aggregated data in reported literature (meta-analysis). Increasing transparency is required in healthcare outcomes and performance, which means that funnel plots will most likely play an increasingly important role as a quality control tool. More widespread application of funnel plots in surgery will help to overcome some of the existing difficulties in assessing and reporting performance and identifying evidence-based information. The assessment and changes in future healthcare delivery could be partly influenced by further development of funnel plot methodology.

  17. Compensating for missing plot observations inforest inventory estimation

    Science.gov (United States)

    Ronald E. McRoberts

    2003-01-01

    The Enhanced Forest Inventory and Analysis program of the U.S. Forest Service has established a nationwide array of permanent field plots, each representing approximately 2400 ha. Each plot has been assigned to one of five interpenetrating, nonoverlapping panels, with one panel selected for measurement on a rotating basis each year. As with most large surveys,...

  18. Estimating mapped-plot forest attributes with ratios of means

    Science.gov (United States)

    S.J. Zarnoch; W.A. Bechtold

    2000-01-01

    The mapped-plot design utilized by the U.S. Department of Agriculture (USDA) Forest Inventory and Analysis and the National Forest Health Monitoring Programs is described. Data from 2458 forested mapped plots systematically spread across 25 States reveal that 35 percent straddle multiple conditions. The ratio-of-means estimator is developed as a method to obtain...

  19. Plots of the experimental and evaluated photoneutron cross-sections

    International Nuclear Information System (INIS)

    Blokhin, A.I.; Nasyrova, S.M.

    1991-08-01

    Graphical plots of experimental data of photon induced nuclear reaction cross-sections are given for many elements and isotopes. The numerical data were taken from the international EXFOR data library which is available from the nuclear data centers. For selected nuclides evaluated data have been included in the plots. (author). Refs, 3 tabs

  20. Refining FIA plot locations using LiDAR point clouds

    Science.gov (United States)

    Charlie Schrader-Patton; Greg C. Liknes; Demetrios Gatziolis; Brian M. Wing; Mark D. Nelson; Patrick D. Miles; Josh Bixby; Daniel G. Wendt; Dennis Kepler; Abbey. Schaaf

    2015-01-01

    Forest Inventory and Analysis (FIA) plot location coordinate precision is often insufficient for use with high resolution remotely sensed data, thereby limiting the use of these plots for geospatial applications and reducing the validity of models that assume the locations are precise. A practical and efficient method is needed to improve coordinate precision. To...

  1. Precise FIA plot registration using field and dense LIDAR data

    Science.gov (United States)

    Demetrios Gatziolis

    2009-01-01

    Precise registration of forest inventory and analysis (FIA) plots is a prerequisite for an effective fusion of field data with ancillary spatial information, which is an approach commonly employed in the mapping of various forest parameters. Although the adoption of Global Positioning System technology has improved the precision of plot coordinates obtained during...

  2. A Guided Inquiry on Hubble Plots and the Big Bang

    Science.gov (United States)

    Forringer, Ted

    2014-01-01

    In our science for non-science majors course "21st Century Physics," we investigate modern "Hubble plots" (plots of velocity versus distance for deep space objects) in order to discuss the Big Bang, dark matter, and dark energy. There are two potential challenges that our students face when encountering these topics for the…

  3. Selection of Plot Remeasurement in an Annual Inventory

    Science.gov (United States)

    Mark H. Hansen; Hans T. Schreuder; Dave Heinzen

    2000-01-01

    A plot selection approach is proposed based on experience from the Annual Forest Inventory System (AFIS) in the Aspen-Birch Unit of northestern Minnesota. The emphasisis on a mixture of strategies. Although the Agricultural Act of 1998 requires that a fixed 20 percent of plots be measured each year in each state, sooner or later we will need to vary the scheme to...

  4. DEVS Models of Palletized Ground Stacking in Storeyed Grain Warehouse

    Directory of Open Access Journals (Sweden)

    Hou Shu-Yi

    2016-01-01

    Full Text Available Processed grain stored in storeyed warehouse is generally stacked on the ground without pallets. However, in order to improve the storing way, we developed a new stacking method, palletized ground stacking. Simulation should be used to present this new storing way. DEVS provides a formalized way to describe the system model. In this paper, DEVS models of palletized ground stacking in storeyed grain warehouse are given and a simulation model is developed by AutoMod.

  5. Investigation on etch characteristics of nanometer-sized magnetic tunnel junction stacks using a HBr/Ar plasma.

    Science.gov (United States)

    Kim, Eun Ho; Xiao, Yu Bin; Kong, Seon Mi; Chung, Chee Won

    2011-07-01

    The etch characteristics of CoFeB magnetic films and magnetic-tunnel-junction (MTJ) stacks masked with Ti films were investigated using an inductively coupled plasma reactive ion etching in a HBr/Ar gas mix. The etch rate, etch selectivity, and etch profile of the CoFeB films were obtained as a function of the HBr concentration. As the HBr gas was added to Ar, the etch rate of the CoFeB films, and the etch selectivity to the Ti hard mask, gradually decreased, but the etch profile of the CoFeB films was improved. The effects of the HBr concentration and etch parameters on the etch profile of the MTJ stacks with a nanometer-sized 70 x 100 nm2 pattern were explored. At 10% HBr concentration, low ICP RF power, and low DC-bias voltage, better etch profiles of the MTJ stacks were obtained without redeposition. It was confirmed that the protective layer containing hydrogen, and the surface bombardment of the Ar ions, played a key role in obtaining a steep sidewall angle in the etch profile. Fine-pattern transfer of the MTJ stacks with a high degree of anisotropy was achieved using a HBr/Ar gas chemistry.

  6. ChIPS - Chandra's Interactive, Publication-Ready Plotting Tool

    Science.gov (United States)

    Miller, Joseph; Burke, D.; Evans, I.; Evans, J.; Fruscione, A.; Germain, G.; McDowell, J.; McLaughlin, W.; Milaszewski, R.

    2009-09-01

    The Chandra Interactive Plotting System, ChIPS, is a powerful component of the CIAO data analysis system that enables users to visualize their data and construct high-quality, publication-ready plots interactively. The user can control almost every aspect of the plot layout and the properties of individual plot components such as tick positions or symbol styles. ChIPS offers a rich interactive environment to help users design and fine tune their plots. Key features of ChIPS include the ability to explore alternative presentations of their data by interactively adjusting plot parameters or plot component properties, or correct mistakes via the included undo/redo functionality, without having to redo the visualizations from the beginning. Through a Python or S-Lang interface, ChIPS provides a set of high-level user routines which hides the details of the underlying environment from the new user. At the same time, the scripting environment affords experienced users the ability to manipulate data or extend existing functionality. New to CIAO 4.2, all users will benefit from being able to interactively develop plots and then save the steps to create the final product as a script. This can then be used to recreate the visualization with additional data sets. Also new in CIAO 4.2 is the ability to integrate plot data with basic imaging. Users can combine their images (in world coordinates) with plot elements such as overlay contours, grids, or annotations to produce high-quality publication-ready output in the formats expected by the major journals.

  7. Sport stacking motor intervention programme for children with ...

    African Journals Online (AJOL)

    The purpose of this study was to explore sport stacking as an alternative intervention approach with typically developing children and in addition to improve DCD. Sport stacking consists of participants stacking and unstacking 12 specially designed plastic cups in predetermined sequences in as little time as possible.

  8. Notes on G-theory of Deligne-Mumford stacks

    OpenAIRE

    Toen, B.

    1999-01-01

    Based on the methods used by the author to prove the Riemann-Roch formula for algebraic stacks, this paper contains a description of the rationnal G-theory of Deligne-Mumford stacks over general bases. We will use these results to study equivariant K-theory, and also to define new filtrations on K-theory of algebraic stacks.

  9. Learning algorithms for stack filter classifiers

    Energy Technology Data Exchange (ETDEWEB)

    Porter, Reid B [Los Alamos National Laboratory; Hush, Don [Los Alamos National Laboratory; Zimmer, Beate G [TEXAS A& M

    2009-01-01

    Stack Filters define a large class of increasing filter that is used widely in image and signal processing. The motivations for using an increasing filter instead of an unconstrained filter have been described as: (1) fast and efficient implementation, (2) the relationship to mathematical morphology and (3) more precise estimation with finite sample data. This last motivation is related to methods developed in machine learning and the relationship was explored in an earlier paper. In this paper we investigate this relationship by applying Stack Filters directly to classification problems. This provides a new perspective on how monotonicity constraints can help control estimation and approximation errors, and also suggests several new learning algorithms for Boolean function classifiers when they are applied to real-valued inputs.

  10. Industrial stacks design; Diseno de chimeneas industriales

    Energy Technology Data Exchange (ETDEWEB)

    Cacheux, Luis [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1986-12-31

    The Instituto de Investigaciones Electricas (IIE) though its Civil Works Department, develops, under contract with CFE`s Gerencia de Proyectos Termoelectricos (Management of Fossil Power Plant Projects), a series of methods for the design of stacks, which pretends to solve the a present day problem: the stack design of the fossil power plants that will go into operation during the next coming years in the country. [Espanol] El Instituto de Investigaciones Electricas (IIE), a traves del Departamento de Ingenieria Civil, desarrolla, bajo contrato con la Gerencia de Proyectos Termoelectricos, de la Comision Federal de Electricidad (CFE), un conjunto de metodos para el diseno de chimeneas, con el que se pretende resolver un problema inmediato: el diseno de las chimeneas de las centrales termoelectricas que entraran en operacion durante los proximos anos, en el pais.

  11. Annular feed air breathing fuel cell stack

    Science.gov (United States)

    Wilson, Mahlon S.

    1996-01-01

    A stack of polymer electrolyte fuel cells is formed from a plurality of unit cells where each unit cell includes fuel cell components defining a periphery and distributed along a common axis, where the fuel cell components include a polymer electrolyte membrane, an anode and a cathode contacting opposite sides of the membrane, and fuel and oxygen flow fields contacting the anode and the cathode, respectively, wherein the components define an annular region therethrough along the axis. A fuel distribution manifold within the annular region is connected to deliver fuel to the fuel flow field in each of the unit cells. In a particular embodiment, a single bolt through the annular region clamps the unit cells together. In another embodiment, separator plates between individual unit cells have an extended radial dimension to function as cooling fins for maintaining the operating temperature of the fuel cell stack.

  12. System for inspection of stacked cargo containers

    Science.gov (United States)

    Derenzo, Stephen [Pinole, CA

    2011-08-16

    The present invention relates to a system for inspection of stacked cargo containers. One embodiment of the invention generally comprises a plurality of stacked cargo containers arranged in rows or tiers, each container having a top, a bottom a first side, a second side, a front end, and a back end; a plurality of spacers arranged in rows or tiers; one or more mobile inspection devices for inspecting the cargo containers, wherein the one or more inspection devices are removeably disposed within the spacers, the inspection means configured to move through the spacers to detect radiation within the containers. The invented system can also be configured to inspect the cargo containers for a variety of other potentially hazardous materials including but not limited to explosive and chemical threats.

  13. Multistage Force Amplification of Piezoelectric Stacks

    Science.gov (United States)

    Xu, Tian-Bing (Inventor); Siochi, Emilie J. (Inventor); Zuo, Lei (Inventor); Jiang, Xiaoning (Inventor); Kang, Jin Ho (Inventor)

    2015-01-01

    Embodiments of the disclosure include an apparatus and methods for using a piezoelectric device, that includes an outer flextensional casing, a first cell and a last cell serially coupled to each other and coupled to the outer flextensional casing such that each cell having a flextensional cell structure and each cell receives an input force and provides an output force that is amplified based on the input force. The apparatus further includes a piezoelectric stack coupled to each cell such that the piezoelectric stack of each cell provides piezoelectric energy based on the output force for each cell. Further, the last cell receives an input force that is the output force from the first cell and the last cell provides an output apparatus force In addition, the piezoelectric energy harvested is based on the output apparatus force. Moreover, the apparatus provides displacement based on the output apparatus force.

  14. Radiation-Tolerant Intelligent Memory Stack - RTIMS

    Science.gov (United States)

    Ng, Tak-kwong; Herath, Jeffrey A.

    2011-01-01

    This innovation provides reconfigurable circuitry and 2-Gb of error-corrected or 1-Gb of triple-redundant digital memory in a small package. RTIMS uses circuit stacking of heterogeneous components and radiation shielding technologies. A reprogrammable field-programmable gate array (FPGA), six synchronous dynamic random access memories, linear regulator, and the radiation mitigation circuits are stacked into a module of 42.7 42.7 13 mm. Triple module redundancy, current limiting, configuration scrubbing, and single- event function interrupt detection are employed to mitigate radiation effects. The novel self-scrubbing and single event functional interrupt (SEFI) detection allows a relatively soft FPGA to become radiation tolerant without external scrubbing and monitoring hardware

  15. Absorption spectra of AA-stacked graphite

    International Nuclear Information System (INIS)

    Chiu, C W; Lee, S H; Chen, S C; Lin, M F; Shyu, F L

    2010-01-01

    AA-stacked graphite shows strong anisotropy in geometric structures and velocity matrix elements. However, the absorption spectra are isotropic for the polarization vector on the graphene plane. The spectra exhibit one prominent plateau at middle energy and one shoulder structure at lower energy. These structures directly reflect the unique geometric and band structures and provide sufficient information for experimental fitting of the intralayer and interlayer atomic interactions. On the other hand, monolayer graphene shows a sharp absorption peak but no shoulder structure; AA-stacked bilayer graphene has two absorption peaks at middle energy and abruptly vanishes at lower energy. Furthermore, the isotropic features are expected to exist in other graphene-related systems. The calculated results and the predicted atomic interactions could be verified by optical measurements.

  16. Development of on-site PAFC stacks

    Energy Technology Data Exchange (ETDEWEB)

    Hotta, K.; Matsumoto, Y. [Kansai Electric Power Co., Amagasaki (Japan); Horiuchi, H.; Ohtani, T. [Mitsubishi Electric Corp., Kobe (Japan)

    1996-12-31

    PAFC (Phosphoric Acid Fuel Cell) has been researched for commercial use and demonstration plants have been installed in various sites. However, PAFC don`t have a enough stability yet, so more research and development must be required in the future. Especially, cell stack needs a proper state of three phases (liquid, gas and solid) interface. It is very difficult technology to keep this condition for a long time. In the small size cell with the electrode area of 100 cm{sup 2}, gas flow and temperature distributions show uniformity. But in the large size cell with the electrode area of 4000 cm{sup 2}, the temperature distributions show non-uniformity. These distributions would cause to be shorten the cell life. Because these distributions make hot-spot and gas poverty in limited parts. So we inserted thermocouples in short-stack for measuring three-dimensional temperature distributions and observed effects of current density and gas utilization on temperature.

  17. Effectiveness of commercial microbial products in enhancing oil degradation in Prince William Sound field plots

    International Nuclear Information System (INIS)

    Venosa, A.D.; Haines, J.R.; Allen, D.M.

    1991-01-01

    In the spring of 1990, previously reported laboratory experiments were conducted on 10 commercial microbial products to test for enhanced biodegradation of weathered crude oil from the Exxon Valdez oil spill. The laboratory tests measured the rate and extent of oil degradation in closed flasks. Weathered oil from the beaches in Alaska and seawater from Prince William Sound were used in the tests. Two of the 10 products were found to provide significantly greater alkane degradation than flasks supplemented with mineral nutrients alone. These two products were selected for further testing on a beach in Prince William Sound. A randomized complete block experiment was designed to compare the effectiveness of these two products in enhancing oil degradation compared to simple fertilizer alone. Four small plots consisting of a no nutrient control, a mineral nutrient plot, and two plots receiving mineral nutrients plus the two products, were laid out on a contaminated beach. These four plots comprised a 'block' of treatments, and this block was replicated four times on the same beach. Triplicate samples of beach sediment were collected at four equally spaced time intervals and analyzed for oil residue weight and alkane hydrocarbon profile changes with time. The objective was to determine if either of the two commercial microbiological products was able to enhance bioremediation of an oil-contaminated beach in Prince William Sound to an extent greater than that achievable by simple fertilizer application. Results indicated no significant differences among the four treatments in the 27-day period of the experiment

  18. CAM and stack air sampler design guide

    International Nuclear Information System (INIS)

    Phillips, T.D.

    1994-01-01

    About 128 air samplers and CAMs presently in service to detect and document potential radioactive release from 'H' and 'F' area tank farm ventilation stacks are scheduled for replacement and/or upgrade by Projects S-5764, S-2081, S-3603, and S-4516. The seven CAMs scheduled to be upgraded by Project S-4516 during 1995 are expected to provide valuable experience for the three remaining projects. The attached document provides design guidance for the standardized High Level Waste air sampling system

  19. Contemporary sample stacking in analytical electrophoresis

    Czech Academy of Sciences Publication Activity Database

    Malá, Zdeňka; Gebauer, Petr; Boček, Petr

    2011-01-01

    Roč. 32, č. 1 (2011), s. 116-126 ISSN 0173-0835 R&D Projects: GA ČR GA203/08/1536; GA ČR GAP206/10/1219; GA AV ČR IAA400310703 Institutional research plan: CEZ:AV0Z40310501 Keywords : biological samples * stacking * trace analysis * zone electrophoresis Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 3.303, year: 2011

  20. Stacked Switched Capacitor Energy Buffer Architecture

    OpenAIRE

    Chen, Minjie; Perreault, David J.; Afridi, Khurram

    2012-01-01

    Electrolytic capacitors are often used for energy buffering applications, including buffering between single-phase ac and dc. While these capacitors have high energy density compared to film and ceramic capacitors, their life is limited. This paper presents a stacked switched capacitor (SSC) energy buffer architecture and some of its topological embodiments, which when used with longer life film capacitors overcome this limitation while achieving effective energy densities comparable to elect...

  1. Thyristor stack for pulsed inductive plasma generation.

    Science.gov (United States)

    Teske, C; Jacoby, J; Schweizer, W; Wiechula, J

    2009-03-01

    A thyristor stack for pulsed inductive plasma generation has been developed and tested. The stack design includes a free wheeling diode assembly for current reversal. Triggering of the device is achieved by a high side biased, self supplied gate driver unit using gating energy derived from a local snubber network. The structure guarantees a hard firing gate pulse for the required high dI/dt application. A single fiber optic command is needed to achieve a simultaneous turn on of the thyristors. The stack assembly is used for switching a series resonant circuit with a ringing frequency of 30 kHz. In the prototype pulsed power system described here an inductive discharge has been generated with a pulse duration of 120 micros and a pulse energy of 50 J. A maximum power transfer efficiency of 84% and a peak power of 480 kW inside the discharge were achieved. System tests were performed with a purely inductive load and an inductively generated plasma acting as a load through transformer action at a voltage level of 4.1 kV, a peak current of 5 kA, and a current switching rate of 1 kA/micros.

  2. Electrochemical Detection in Stacked Paper Networks.

    Science.gov (United States)

    Liu, Xiyuan; Lillehoj, Peter B

    2015-08-01

    Paper-based electrochemical biosensors are a promising technology that enables rapid, quantitative measurements on an inexpensive platform. However, the control of liquids in paper networks is generally limited to a single sample delivery step. Here, we propose a simple method to automate the loading and delivery of liquid samples to sensing electrodes on paper networks by stacking multiple layers of paper. Using these stacked paper devices (SPDs), we demonstrate a unique strategy to fully immerse planar electrodes by aqueous liquids via capillary flow. Amperometric measurements of xanthine oxidase revealed that electrochemical sensors on four-layer SPDs generated detection signals up to 75% higher compared with those on single-layer paper devices. Furthermore, measurements could be performed with minimal user involvement and completed within 30 min. Due to its simplicity, enhanced automation, and capability for quantitative measurements, stacked paper electrochemical biosensors can be useful tools for point-of-care testing in resource-limited settings. © 2015 Society for Laboratory Automation and Screening.

  3. Novel vehicle detection system based on stacked DoG kernel and AdaBoost

    Science.gov (United States)

    Kang, Hyun Ho; Lee, Seo Won; You, Sung Hyun

    2018-01-01

    This paper proposes a novel vehicle detection system that can overcome some limitations of typical vehicle detection systems using AdaBoost-based methods. The performance of the AdaBoost-based vehicle detection system is dependent on its training data. Thus, its performance decreases when the shape of a target differs from its training data, or the pattern of a preceding vehicle is not visible in the image due to the light conditions. A stacked Difference of Gaussian (DoG)–based feature extraction algorithm is proposed to address this issue by recognizing common characteristics, such as the shadow and rear wheels beneath vehicles—of vehicles under various conditions. The common characteristics of vehicles are extracted by applying the stacked DoG shaped kernel obtained from the 3D plot of an image through a convolution method and investigating only certain regions that have a similar patterns. A new vehicle detection system is constructed by combining the novel stacked DoG feature extraction algorithm with the AdaBoost method. Experiments are provided to demonstrate the effectiveness of the proposed vehicle detection system under different conditions. PMID:29513727

  4. Guanine base stacking in G-quadruplex nucleic acids

    Science.gov (United States)

    Lech, Christopher Jacques; Heddi, Brahim; Phan, Anh Tuân

    2013-01-01

    G-quadruplexes constitute a class of nucleic acid structures defined by stacked guanine tetrads (or G-tetrads) with guanine bases from neighboring tetrads stacking with one another within the G-tetrad core. Individual G-quadruplexes can also stack with one another at their G-tetrad interface leading to higher-order structures as observed in telomeric repeat-containing DNA and RNA. In this study, we investigate how guanine base stacking influences the stability of G-quadruplexes and their stacked higher-order structures. A structural survey of the Protein Data Bank is conducted to characterize experimentally observed guanine base stacking geometries within the core of G-quadruplexes and at the interface between stacked G-quadruplex structures. We couple this survey with a systematic computational examination of stacked G-tetrad energy landscapes using quantum mechanical computations. Energy calculations of stacked G-tetrads reveal large energy differences of up to 12 kcal/mol between experimentally observed geometries at the interface of stacked G-quadruplexes. Energy landscapes are also computed using an AMBER molecular mechanics description of stacking energy and are shown to agree quite well with quantum mechanical calculated landscapes. Molecular dynamics simulations provide a structural explanation for the experimentally observed preference of parallel G-quadruplexes to stack in a 5′–5′ manner based on different accessible tetrad stacking modes at the stacking interfaces of 5′–5′ and 3′–3′ stacked G-quadruplexes. PMID:23268444

  5. Final Report - MEA and Stack Durability for PEM Fuel Cells

    Energy Technology Data Exchange (ETDEWEB)

    Yandrasits, Michael A.

    2008-02-15

    Proton exchange membrane fuel cells are expected to change the landscape of power generation over the next ten years. For this to be realized one of the most significant challenges to be met for stationary systems is lifetime, where 40,000 hours of operation with less than 10% decay is desired. This project conducted fundamental studies on the durability of membrane electrode assemblies (MEAs) and fuel cell stack systems with the expectation that knowledge gained from this project will be applied toward the design and manufacture of MEAs and stack systems to meet DOE’s 2010 stationary fuel cell stack systems targets. The focus of this project was PEM fuel cell durability – understanding the issues that limit MEA and fuel cell system lifetime, developing mitigation strategies to address the lifetime issues and demonstration of the effectiveness of the mitigation strategies by system testing. To that end, several discoveries were made that contributed to the fundamental understanding of MEA degradation mechanisms. (1) The classically held belief that membrane degradation is solely due to end-group “unzipping” is incorrect; there are other functional groups present in the ionomer that are susceptible to chemical attack. (2) The rate of membrane degradation can be greatly slowed or possibly eliminated through the use of additives that scavenge peroxide or peroxyl radicals. (3) Characterization of GDL using dry gases is incorrect due to the fact that fuel cells operate utilizing humidified gases. The proper characterization method involves using wet gas streams and measuring capillary pressure as demonstrated in this project. (4) Not all Platinum on carbon catalysts are created equally – the major factor impacting catalyst durability is the type of carbon used as the support. (5) System operating conditions have a significant impact of lifetime – the lifetime was increased by an order of magnitude by changing the load profile while all other variables remain

  6. PLOTTAB, Curve and Point Plotting with Error Bars

    International Nuclear Information System (INIS)

    1999-01-01

    1 - Description of program or function: PLOTTAB is designed to plot any combination of continuous curves and/or discrete points (with associated error bars) using user supplied titles and X and Y axis labels and units. If curves are plotted, the first curve may be used as a standard; the data and the ratio of the data to the standard will be plotted. 2 - Method of solution: PLOTTAB: The program has no idea of what data is being plotted and yet by supplying titles, X and Y axis labels and units the user can produce any number of plots with each plot containing almost any combination of curves and points with each plot properly identified. In order to define a continuous curve between tabulated points, this program must know how to interpolate between points. By input the user may specify either the default option of linear x versus linear y interpolation or alternatively log x and/or log Y interpolation. In all cases, regardless of the interpolation specified, the program will always interpolate the data to the plane of the plot (linear or log x and y plane) in order to present the true variation of the data between tabulated points, based on the user specified interpolation law. Tabulated points should be tabulated at a sufficient number of x values to insure that the difference between the specified interpolation and the 'true' variation of a curve between tabulated values is relatively small. 3 - Restrictions on the complexity of the problem: A combination of up to 30 curves and sets of discrete points may appear on each plot. If the user wishes to use this program to compare different sets of data, all of the data must be in the same units

  7. TAURUS, Post-processor of 3-D Finite Elements Plots

    International Nuclear Information System (INIS)

    Brown, B.E.; Hallquist, J.O.; Kennedy, T.

    2002-01-01

    Description of program or function: TAURUS reads the binary plot files generated by the LLNL three-dimensional finite element analysis codes, NIKE3D (NESC 9725), DYNA3D (NESC 9909), TACO3D (NESC 9838), TOPAZ3D (NESC9599) and GEMINI and plots contours, time histories, and deformed shapes. Contours of a large number of quantities may be plotted on meshes consisting of plate, shell, and solid type elements. TAURUS can compute a variety of strain measures, reaction forces along constrained boundaries, and momentum. TAURUS has three phases: initialization, geometry display with contouring, and time history processing

  8. Superplot: a graphical interface for plotting and analysing MultiNest output

    Science.gov (United States)

    Fowlie, Andrew; Bardsley, Michael Hugh

    2016-11-01

    We present an application, Superplot, for calculating and plotting statistical quantities relevant to parameter inference from a "chain" of samples drawn from a parameter space, produced by, e.g., MultiNest. A simple graphical interface allows one to browse a chain of many variables quickly, and make publication quality plots of, inter alia, one- and two-dimensional profile likelihood, posterior pdf (with kernel density estimation), confidence intervals and credible regions. In this short manual, we document installation and basic usage, and define all statistical quantities and conventions. The code is fully compatible with Linux and Windows. All functionality is available on Mac OSX, though it must be invoked by the command line rather than a graphical interface.

  9. True versus perturbed forest inventory plot locations for modeling: a simulation study

    Science.gov (United States)

    John W. Coulston; Kurt H. Riitters; Ronald E. McRoberts; William D. Smith

    2006-01-01

    USDA Forest Service Forest Inventory and Analysis plot information is widely used for timber inventories, forest health assessments, and environmental risk analyses. With few exceptions, true plot locations are not revealed; the plot coordinates are manipulated to obscure the location of field plots and thereby preserve plot integrity. The influence of perturbed plot...

  10. Brains striving for coherence: Long-term cumulative plot formation in the default mode network.

    Science.gov (United States)

    Tylén, K; Christensen, P; Roepstorff, A; Lund, T; Østergaard, S; Donald, M

    2015-11-01

    Many everyday activities, such as engaging in conversation or listening to a story, require us to sustain attention over a prolonged period of time while integrating and synthesizing complex episodic content into a coherent mental model. Humans are remarkably capable of navigating and keeping track of all the parallel social activities of everyday life even when confronted with interruptions or changes in the environment. However, the underlying cognitive and neurocognitive mechanisms of such long-term integration and profiling of information remain a challenge to neuroscience. While brain activity is generally traceable within the short time frame of working memory (milliseconds to seconds), these integrative processes last for minutes, hours or even days. Here we report two experiments on story comprehension. Experiment I establishes a cognitive dissociation between our comprehension of plot and incidental facts in narratives: when episodic material allows for long-term integration in a coherent plot, we recall fewer factual details. However, when plot formation is challenged, we pay more attention to incidental facts. Experiment II investigates the neural underpinnings of plot formation. Results suggest a central role for the brain's default mode network related to comprehension of coherent narratives while incoherent episodes rather activate the frontoparietal control network. Moreover, an analysis of cortical activity as a function of the cumulative integration of narrative material into a coherent story reveals to linear modulations of right hemisphere posterior temporal and parietal regions. Together these findings point to key neural mechanisms involved in the fundamental human capacity for cumulative plot formation. Copyright © 2015 Elsevier Inc. All rights reserved.

  11. Implementation of plot options for the NJOY module DTFR

    International Nuclear Information System (INIS)

    Caldeira, A.D.; Ono, S.

    1989-02-01

    The modifications performed in the DTFR module of NJOY to plot multigroup and pointwise nuclear data and transfer matrices, utilizing the sofware package UNIPLOT in the CDC CYBER 170/750 system, are presented. (author) [pt

  12. The master plot in the audiovisual narrative. The western case.

    Directory of Open Access Journals (Sweden)

    José Félix GONZÁLEZ SÁNCHEZ

    2015-05-01

    Full Text Available A plot provides us the story that it offers a hyphen and later a film. Plots are limited, however possibilities, argument them that these offer music infinite. At the same time, we can say that all cultures avail themselves of some plots and similar arguments to structure their mythical stories. In addition, United States is the modern nation where better a dialectic relation between the myth and story keeps. At this nation, the significance of the event has been shown and you have gotten free through the myth. We will see through this article how the western is the kind of American cinema what else and better answer for the folkloric traditional story to the cánones, because your plots have been taken directly of the classical legends.

  13. SCALPLO, Plotting of Flux Output from SCALE Program

    International Nuclear Information System (INIS)

    Hersman, A.; De Leege, P.F.A.; Hoogenboom, J.E.

    1993-01-01

    1 - Description of program or function: SCALPLO is a plot program, designed to plot flux, power and spectrum information. Data exchange between SCALE modules and SCALPLO is via CCCC-interface files. As not all modules can produce these files, there are special routines supplied with SCALPLO that can produce CCCC-like files. These routines can be included in the code and for XSDRPM, CITATION, ANISN and DOT, the place to include these routines is supplied. 2 - Method of solution: SCALPLO consists of two sections. Firstly the pre-processor, which selects and reads the required data. Secondly the plot section which produces the plot on the selected output device. 3 - Restrictions on the complexity of the problem: SCALPLO requires DISSPLA version 11.0 or higher. The choice of output device depends on the devices installed

  14. An Unusual Application of NASTRAN Contour Plotting Capability

    Science.gov (United States)

    Mittal, S.; Gallo, M.; Wang, T.

    1985-01-01

    A procedure is presented for obtaining contour plots of any physical quantity defined on a number of points of the surface of a structure. Rigid Format 1 of HEAT approach in Cosmic NASTRAN is ALTERED to enable use of contour plotting capability for scalar quantities. The ALTERED DMAP sequence is given. Examples include temperature distribution on the face of a cooled laser mirror and the angle of incidence or a radome surface.

  15. The Effect of Plot Size on Some Pratylenchus Penetrans ...

    African Journals Online (AJOL)

    Pratylenchus penetrans counts obtained from a rose field, sampled sequentially by decreasing the plot sizes were computed to obtain the respective sample means, variance and k-value of the negative binomial distribution. Plots 21 m x 80 m, 3.6 m x 3.6 m and 0.6 m x 0.6 m were sampled for the nematode. It is reported ...

  16. Development and Characterization of an Electrically Rechargeable Zinc-Air Battery Stack

    Directory of Open Access Journals (Sweden)

    Hongyun Ma

    2014-10-01

    Full Text Available An electrically rechargeable zinc-air battery stack consisting of three single cells in series was designed using a novel structured bipolar plate with air-breathing holes. Alpha-MnO2 and LaNiO3 severed as the catalysts for the oxygen reduction reaction (ORR and oxygen evolution reaction (OER. The anodic and cathodic polarization and individual cell voltages were measured at constant charge-discharge (C-D current densities indicating a uniform voltage profile for each single cell. One hundred C-D cycles were carried out for the stack. The results showed that, over the initial 10 cycles, the average C-D voltage gap was about 0.94 V and the average energy efficiency reached 89.28% with current density charging at 15 mA·cm−2 and discharging at 25 mA·cm−2. The total increase in charging voltage over the 100 C-D cycles was ~1.56% demonstrating excellent stability performance. The stack performance degradation was analyzed by galvanostatic electrochemical impedance spectroscopy. The charge transfer resistance of ORR increased from 1.57 to 2.21 Ω and that of Zn/Zn2+ reaction increased from 0.21 to 0.34 Ω after 100 C-D cycles. The quantitative analysis guided the potential for the optimization of both positive and negative electrodes to improve the cycle life of the cell stack.

  17. Reviewing ChIPS, The Chandra Imaging and Plotting System

    Science.gov (United States)

    Miller, J.; Burke, D. J.; Evans, I. N.; Evans, J. D.; McLaughlin, W.

    2015-09-01

    The Chandra Imaging and Plotting System (ChIPS) is a 2D plotting system designed to allow users to easily create, manipulate, and produce publication quality visualizations. ChIPS has a simple but very powerful interactive interface that allows users to dynamically modify the contents and layout of their plots quickly and efficiently, with the results of any changes being immediately visible. ChIPS allows users to construct their plots fully interactively, and then save the final plot commands as a Python script. This bypasses the need to iteratively edit and rerun the script when developing the plot. Features such as undo and redo commands allow users to easily step backwards and forwards through previous commands, while the ability so save ChIPS sessions in a platform-independent state file allows the session to be restored at any time, even on another machine. Because ChIPS offers a Python interface, users can analyze their data using the broad array of modules offered in Python, and visualize the information in ChIPS at the same time. In this paper we explore the design decisions behind the development of ChIPS and some of the lessons learned along the way.

  18. Improved Direct Methanol Fuel Cell Stack

    Science.gov (United States)

    Wilson, Mahlon S.; Ramsey, John C.

    2005-03-08

    A stack of direct methanol fuel cells exhibiting a circular footprint. A cathode and anode manifold, tie-bolt penetrations and tie-bolts are located within the circular footprint. Each fuel cell uses two graphite-based plates. One plate includes a cathode active area that is defined by serpentine channels connecting the inlet and outlet cathode manifold. The other plate includes an anode active area defined by serpentine channels connecting the inlet and outlet of the anode manifold, where the serpentine channels of the anode are orthogonal to the serpentine channels of the cathode. Located between the two plates is the fuel cell active region.

  19. NSF tandem stack support structure deflection characteristics

    International Nuclear Information System (INIS)

    Cook, J.

    1979-12-01

    Results are reported of load tests carried out on the glass legs of the insulating stack of the 30 MV tandem Van de Graaff accelerator now under construction at Daresbury Laboratory. The tests to investigate the vulnerability of the legs when subjected to tensile stresses were designed to; establish the angle of rotation of the pads from which the stresses in the glass legs may be calculated, proof-test the structure and at the same time reveal any asymmetry in pad rotations or deflections, and to confirm the validity of the computer design analysis. (UK)

  20. Compliant Glass Seals for SOFC Stacks

    Energy Technology Data Exchange (ETDEWEB)

    Chou, Yeong -Shyung [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Choi, Jung-Pyung [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Xu, Wei [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Stephens, Elizabeth V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Koeppel, Brian J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Stevenson, Jeffry W. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lara-Curzio, Edgar [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2014-04-30

    This report summarizes results from experimental and modeling studies performed by participants in the Solid-State Energy Conversion Alliance (SECA) Core Technology Program, which indicate that compliant glass-based seals offer a number of potential advantages over conventional seals based on de-vitrifying glasses, including reduced stresses during stack operation and thermal cycling, and the ability to heal micro-damage induced during thermal cycling. The properties and composition of glasses developed and/or investigated in these studies are reported, along with results from long-term (up to 5,800h) evaluations of seals based on a compliant glass containing ceramic particles or ceramic fibers.

  1. Effects of combustible stacking in large compartments

    DEFF Research Database (Denmark)

    Gentili, Filippo; Giuliani, Luisa; Bontempi, Franco

    2013-01-01

    This paper focuses on the modelling of fire in case of various distributions of combustible materials in a large compartment. Large compartments often represent a challenge for structural fire safety, because of lack of prescriptive rules to follow and difficulties of taking into account the effect...... to different stacking configurations of the pallets with the avail of a CFD code. The results in term of temperatures of the hot gasses and of the steel elements composing the structural system are compared with simplified analytical model of localized and post-flashover fires, with the aim of highlighting...

  2. Displacive phase transformations and generalized stacking faults

    Czech Academy of Sciences Publication Activity Database

    Paidar, Václav; Ostapovets, Andriy; Duparc, O. H.; Khalfallah, O.

    2012-01-01

    Roč. 122, č. 3 (2012), s. 490-492 ISSN 0587-4246. [International Symposium on Physics of Materials, ISPMA /12./. Praha, 04.09.2011-08.09.2011] R&D Projects: GA AV ČR IAA100100920 Institutional research plan: CEZ:AV0Z10100520 Keywords : ab-initio calculations * close-packed structures * generalized stacking faults * homogeneous deformation * lattice deformation * many-body potentials Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.531, year: 2012

  3. Sampled-time control of a microbial fuel cell stack

    Science.gov (United States)

    Boghani, Hitesh C.; Dinsdale, Richard M.; Guwy, Alan J.; Premier, Giuliano C.

    2017-07-01

    Research into microbial fuel cells (MFCs) has reached the point where cubic metre-scale systems and stacks are being built and tested. Apart from performance enhancement through catalysis, materials and design, an important research area for industrial applicability is stack control, which can enhance MFCs stack power output. An MFC stack is controlled using a sampled-time digital control strategy, which has the advantage of intermittent operation with consequent power saving, and when used in a hybrid series stack connectivity, can avoid voltage reversals. A MFC stack comprising four tubular MFCs was operated hydraulically in series. Each MFC was connected to an independent controller and the stack was connected electrically in series, creating a hybrid-series connectivity. The voltage of each MFC in the stack was controlled such that the overall series stack voltage generated was the algebraic sum (1.26 V) of the individual MFC voltages (0.32, 0.32, 0.32 and 0.3). The controllers were able to control the individual voltages to the point where 2.52 mA was drawn from the stack at a load of 499.9 Ω (delivering 3.18 mW). The controllers were able to reject the disturbances and perturbations caused by electrical loading, temperature and substrate concentration.

  4. Summarizing the incidence of adverse events using volcano plots and time intervals.

    Science.gov (United States)

    Zink, Richard C; Wolfinger, Russell D; Mann, Geoffrey

    2013-01-01

    Adverse event incidence analyses are a critical component for describing the safety profile of any new intervention. The results typically are presented in lengthy summary tables. For therapeutic areas where patients have frequent adverse events, analysis and interpretation are made more difficult by the sheer number and variety of events that occur. Understanding the risk in these instances becomes even more crucial. We describe a space-saving graphical summary that overcomes the limitations of traditional presentations of adverse events and improves interpretability of the safety profile. We present incidence analyses of adverse events graphically using volcano plots to highlight treatment differences. Data from a clinical trial of patients experiencing an aneurysmal subarachnoid hemorrhage are used for illustration. Adjustments for multiplicity are illustrated. Color is used to indicate the treatment with higher incidence; bubble size represents the total number of events that occur in the treatment arms combined. Adjustments for multiple comparisons are displayed in a manner to indicate clearly those events for which the difference between treatment arms is statistically significant. Furthermore, adverse events can be displayed by time intervals, with multiple volcano plots or animation to appreciate changes in adverse event risk over time. Such presentations can emphasize early differences across treatments that may resolve later or highlight events for which treatment differences may become more substantial with longer follow-up. Treatment arms are compared in a pairwise fashion. Volcano plots are space-saving tools that emphasize important differences between the adverse event profiles of two treatment arms. They can incorporate multiplicity adjustments in a manner that is straightforward to interpret and, by using time intervals, can illustrate how adverse event risk changes over the course of a clinical trial.

  5. Water content estimated from point scale to plot scale

    Science.gov (United States)

    Akyurek, Z.; Binley, A. M.; Demir, G.; Abgarmi, B.

    2017-12-01

    Soil moisture controls the portioning of rainfall into infiltration and runoff. Here we investigate measurements of soil moisture using a range of techniques spanning different spatial scales. In order to understand soil water content in a test basin, 512 km2 in area, in the south of Turkey, a Cosmic Ray CRS200B soil moisture probe was installed at elevation of 1459 m and an ML3 ThetaProbe (CS 616) soil moisture sensor was established at 5cm depth used to get continuous soil moisture. Neutron count measurements were corrected for the changes in atmospheric pressure, atmospheric water vapour and intensity of incoming neutron flux. The calibration of the volumetric soil moisture was performed, from the laboratory analysis, the bulk density varies between 1.719 (g/cm3) -1.390 (g/cm3), and the dominant soil texture is silty clay loam and silt loamThe water content reflectometer was calibrated for soil-specific conditions and soil moisture estimates were also corrected with respect to soil temperature. In order to characterize the subsurface, soil electrical resistivity tomography was used. Wenner and Schlumberger array geometries were used with electrode spacing varied from 1m- 5 m along 40 m and 200 m profiles. From the inversions of ERT data it is apparent that within 50 m distance from the CRS200B, the soil is moderately resistive to a depth of 2m and more conductive at greater depths. At greater distances from the CRS200B, the ERT results indicate more resistive soils. In addition to the ERT surveys, ground penetrating radar surveys using a common mid-point configuration was used with 200MHz antennas. The volumetric soil moisture obtained from GPR appears to overestimate those based on TDR observations. The values obtained from CS616 (at a point scale) and CRS200B (at a mesoscale) are compared with the values obtained at a plot scale. For the field study dates (20-22.06.2017) the volumetric moisture content obtained from CS616 were 25.14%, 25.22% and 25

  6. AC impedance diagnosis of a 500 W PEM fuel cell stack . Part I: Stack impedance

    Science.gov (United States)

    Yuan, Xiaozi; Sun, Jian Colin; Blanco, Mauricio; Wang, Haijiang; Zhang, Jiujun; Wilkinson, David P.

    Diagnosis of stack performance is of importance to proton exchange membrane (PEM) fuel cell research. This paper presents the diagnostic testing results of a 500 W Ballard Mark V PEM fuel cell stack with an active area of 280 cm 2 by electrochemical impedance spectroscopy (EIS). The EIS was measured using a combination of a FuelCon test station, a TDI loadbank, and a Solartron 1260 Impedance/Gain-Phase Analyzer operating in the galvanostatic mode. The method described in this work can obtain the impedance spectra of fuel cells with a larger geometric surface area and power, which are normally difficult to measure due to the limitations on commercial load banks operating at high currents. By using this method, the effects of temperature, flow rate, and humidity on the stack impedance spectra were examined. The results of the electrochemical impedance analysis show that with increasing temperature, the charge transfer resistance decreases due to the slow oxygen reduction reaction (ORR) process at low temperature. If the stack is operated at a fixed air flow rate, a low frequency arc appears and grows with increasing current due to the shortage of air. The anode humidification cut-off does not affect the spectra compared to the cut-off for cathode humidification.

  7. Stray field interaction of stacked amorphous tapes

    International Nuclear Information System (INIS)

    Guenther, Wulf; Flohrer, Sybille

    2008-01-01

    In this study, magnetic cores made of amorphous rectangular tape layers are investigated. The quality factor Q of the tape material decreases rapidly, however, when stacking at least two tape layers. The hysteresis loop becomes non-linear, and the coercivity increases. These effects are principally independent of the frequency and occur whether tape layers are insulated or not. The Kerr-microscopy was used to monitor local hysteresis loops by varying the distance of two tape layers. The magnetization direction of each magnetic domain is influenced by the anisotropy axis, the external magnetic field and the stray field of magnetic domains of the neighboring tape layers. We found that crossed easy axes (as the extreme case for inclined axes) of congruent domains retain the remagnetization and induce a plateau of the local loop. Summarizing local loops leads to the observed increase of coercivity and non-linearity of the inductively measured loop. A high Q-factor can be preserved if the easy axes of stacked tape layers are identical within the interaction range in the order of mm

  8. Annular feed air breathing fuel cell stack

    Science.gov (United States)

    Wilson, Mahlon S.; Neutzler, Jay K.

    1997-01-01

    A stack of polymer electrolyte fuel cells is formed from a plurality of unit cells where each unit cell includes fuel cell components defining a periphery and distributed along a common axis, where the fuel cell components include a polymer electrolyte membrane, an anode and a cathode contacting opposite sides of the membrane, and fuel and oxygen flow fields contacting the anode and the cathode, respectively, wherein the components define an annular region therethrough along the axis. A fuel distribution manifold within the annular region is connected to deliver fuel to the fuel flow field in each of the unit cells. The fuel distribution manifold is formed from a hydrophilic-like material to redistribute water produced by fuel and oxygen reacting at the cathode. In a particular embodiment, a single bolt through the annular region clamps the unit cells together. In another embodiment, separator plates between individual unit cells have an extended radial dimension to function as cooling fins for maintaining the operating temperature of the fuel cell stack.

  9. Stacking Analysis of Binary Systems with HAWC

    Science.gov (United States)

    Brisbois, Chad; HAWC Collaboration

    2017-01-01

    Detecting binary systems at TeV energies is an important problem because only a handful of such systems are currently known. The nature of such systems is typically thought to be composed of a compact object and a massive star. The TeV emission from these systems does not obviously correspond to emission in GeV or X-ray, where many binary systems have previously been found. This study focuses on a stacking method to detect TeV emission from LS 5039, a known TeV binary, to test its efficacy in HAWC data. Stacking is a widely employed method for increasing signal to noise ratio in optical astronomy, but has never been attempted previously with HAWC. HAWC is an ideal instrument to search for TeV binaries, because of its wide field of view and high uptime. Applying this method to the entire sky may allow HAWC to detect binary sources of very short or very long periods not sensitive to current analyses. NSF, DOE, Los Alamos, Michigan Tech, CONACyt, UNAM, BUAP.

  10. High performance zinc air fuel cell stack

    Science.gov (United States)

    Pei, Pucheng; Ma, Ze; Wang, Keliang; Wang, Xizhong; Song, Mancun; Xu, Huachi

    2014-03-01

    A zinc air fuel cell (ZAFC) stack with inexpensive manganese dioxide (MnO2) as the catalyst is designed, in which the circulation flowing potassium hydroxide (KOH) electrolyte carries the reaction product away and acts as a coolant. Experiments are carried out to investigate the characteristics of polarization, constant current discharge and dynamic response, as well as the factors affecting the performance and uniformity of individual cells in the stack. The results reveal that the peak power density can be as high as 435 mW cm-2 according to the area of the air cathode sheet, and the influence factors on cell performance and uniformity are cell locations, filled state of zinc pellets, contact resistance, flow rates of electrolyte and air. It is also shown that the time needed for voltages to reach steady state and that for current step-up or current step-down are both in milliseconds, indicating the ZAFC can be excellently applied to vehicles with rapid dynamic response demands.

  11. Generalized stacking fault energies of alloys.

    Science.gov (United States)

    Li, Wei; Lu, Song; Hu, Qing-Miao; Kwon, Se Kyun; Johansson, Börje; Vitos, Levente

    2014-07-02

    The generalized stacking fault energy (γ surface) provides fundamental physics for understanding the plastic deformation mechanisms. Using the ab initio exact muffin-tin orbitals method in combination with the coherent potential approximation, we calculate the γ surface for the disordered Cu-Al, Cu-Zn, Cu-Ga, Cu-Ni, Pd-Ag and Pd-Au alloys. Studying the effect of segregation of the solute to the stacking fault planes shows that only the local chemical composition affects the γ surface. The calculated alloying trends are discussed using the electronic band structure of the base and distorted alloys.Based on our γ surface results, we demonstrate that the previous revealed 'universal scaling law' between the intrinsic energy barriers (IEBs) is well obeyed in random solid solutions. This greatly simplifies the calculations of the twinning measure parameters or the critical twinning stress. Adopting two twinnability measure parameters derived from the IEBs, we find that in binary Cu alloys, Al, Zn and Ga increase the twinnability, while Ni decreases it. Aluminum and gallium yield similar effects on the twinnability.

  12. Computerized plutonium laboratory-stack monitoring system

    International Nuclear Information System (INIS)

    Stafford, R.G.; DeVore, R.K.

    1977-01-01

    The Los Alamos Scientific Laboratory has recently designed and constructed a Plutonium Research and Development Facility to meet design criteria imposed by the United States Energy Research and Development Administration. A primary objective of the design criteria is to assure environmental protection and to reliably monitor plutonium effluent via the ventilation exhaust systems. A state-of-the-art facility exhaust air monitoring system is described which establishes near ideal conditions for evaluating plutonium activity in the stack effluent. Total and static pressure sensing manifolds are incorporated to measure average velocity and integrated total discharge air volume. These data are logged at a computer which receives instrument data through a multiplex scanning system. A multipoint isokinetic sampling assembly with associated instrumentation is described. Continuous air monitors have been designed to sample from the isokinetic sampling assembly and transmit both instantaneous and integrated stack effluent concentration data to the computer and various cathode ray tube displays. The continuous air monitors also serve as room air monitors in the plutonium facility with the primary objective of timely evacuation of personnel if an above tolerance airborne plutonium concentration is detected. Several continuous air monitors are incorporated in the ventilation system to assist in identification of release problem areas

  13. Description of gasket failure in a 7 cell PEMFC stack

    Energy Technology Data Exchange (ETDEWEB)

    Husar, Attila; Serra, Maria [Institut de Robotica i Informatica Industrial, Parc Tecnologic de Barcelona, Edifici U, C. Llorens i Artigas, 4-6, 2a Planta, 08028 Barcelona (Spain); Kunusch, Cristian [Laboratorio de Electronica Industrial Control e Instrumentacion, Facultad de Ingenieria, UNLP (Argentina)

    2007-06-10

    This article presents the data and the description of a fuel cell stack that failed due to gasket degradation. The fuel cell under study is a 7 cell stack. The unexpected change in several variables such as temperature, pressure and voltage indicated the possible failure of the stack. The stack was monitored over a 6 h period in which data was collected and consequently analyzed to conclude that the fuel cell stack failed due to a crossover leak on the anode inlet port located on the cathode side gasket of cell 2. This stack failure analysis revealed a series of indicators that could be used by a super visional controller in order to initiate a shutdown procedure. (author)

  14. Online plot services for paleomagnetism and rock magnetism

    Science.gov (United States)

    Hatakeyama, T.

    2017-12-01

    In paleomagnetism and rock magnetism, a lot of types of original plots are used for obtained data from measurements. Many researchers in paleomagnetism often use not only general-purpose plotting programs such as Microsoft Excel but also single-purpose tools. A large benefit of using the latter tools is that we can make a beautiful figure for our own data. However, those programs require specific environment for their operation such as type of hardware and platform, type of operation system and its version, libraries for execution and so on. Therefore, it is difficult to share the result and graphics among the collaborators who use different environments on their PCs. Thus, one of the best solution is likely a program operated on popular environment. The most popular is web environment as we all know. Almost all current operating systems have web browsers as standard and all people use them regularly. Now we provide a web-based service plotting paleomagnetic results easily.We develop original programs with a command-line user interface (non-GUI), and we prepared web pages for input of the simple measured data and options and a wrapper script which transfers the entered values to the program. The results, analyzed values and plotted graphs from the program are shown in the HTML page and downloadable. Our plot services are provided in http://mage-p.org/mageplot/. In this talk, we introduce our program and service and discuss the philosophy and efficiency of these services.

  15. Quadratic forms and Clifford algebras on derived stacks

    OpenAIRE

    Vezzosi, Gabriele

    2013-01-01

    In this paper we present an approach to quadratic structures in derived algebraic geometry. We define derived n-shifted quadratic complexes, over derived affine stacks and over general derived stacks, and give several examples of those. We define the associated notion of derived Clifford algebra, in all these contexts, and compare it with its classical version, when they both apply. Finally, we prove three main existence results for derived shifted quadratic forms over derived stacks, define ...

  16. Use of impedance tagging to monitor fuel cell stack performance

    Science.gov (United States)

    Silva, Gregory

    Fuel cells are electrochemical device that are traditionally assembled in stacks to perform meaningful work. Monitoring the state of the stack is vitally important to ensure that it is operating efficiently and that constituent cells are not failing for one of a several common reasons including membrane dehydration, gas diffusion layer flooding, reactant starvation, and physical damage. Current state-of-the-art monitoring systems are costly and require at least one connection per cell on the stack, which introduces reliability concerns for stacks consisting of hundreds of cells. This thesis presents a novel approach for diagnosing problems in a fuel cell stack that attempts to reduce the cost and complexity of monitoring cells in a stack. The proposed solution modifies the electrochemical impedance spectroscopy (EIS) response of each cell in the stack by connecting an electrical tag in parallel with each cell. This approach allows the EIS response of the entire stack to identify and locate problems in the stack. Capacitors were chosen as tags because they do not interfere with normal stack operation and because they can generate distinct stack EIS responses. An experiment was performed in the Center for Automation Technologies an Systems (CATS) fuel cell laboratory at Rensselaer Polytechnic Institute (RPI) to perform EIS measurements on a single cell with and without capacitor tags to investigate the proposed solution. The EIS data collected from this experiment was used to create a fuel cell model to investigate the proposed solution under ideal conditions. This thesis found that, although the concept shows some promise in simulations, significant obstacles to implementing the proposed solution. Observed EIS response when the capacitor tags were connected did not match the expected EIS response. Constraints on the capacitor tags found by the model impose significant manufacturing challenges to the proposed solution. Further development of the proposed solution is

  17. Stacked Heterogeneous Neural Networks for Time Series Forecasting

    Directory of Open Access Journals (Sweden)

    Florin Leon

    2010-01-01

    Full Text Available A hybrid model for time series forecasting is proposed. It is a stacked neural network, containing one normal multilayer perceptron with bipolar sigmoid activation functions, and the other with an exponential activation function in the output layer. As shown by the case studies, the proposed stacked hybrid neural model performs well on a variety of benchmark time series. The combination of weights of the two stack components that leads to optimal performance is also studied.

  18. A novel configuration for direct internal reforming stacks

    Science.gov (United States)

    Fellows, Richard

    This paper presents a stack concept that can be applied to both molten carbonate fuel cell (MCFC) and solid oxide fuel cell (SOFC) internal reforming stacks. It employs anode recycle and allows the design of very simple system configurations, while giving enhanced efficiencies and high specific power densities. The recycle of anode exit gas to the anode inlet has previously been proposed as a means of preventing carbon deposition in direct internal reforming (DIR) stacks. When applied to a normal stack this reduces the Nernst voltages because the recycle stream is relatively depleted in hydrogen. In the concept proposed here, known as the `Smarter' stack, there are two anode exit streams, one of which is depleted, while the other is relatively undepleted. The depleted stream passes directly to the burner, and the undepleted stream is recycled to the stack inlet. By this means high Nernst voltages are achieved in the stack. The concept has been simulated and assessed for parallel-flow and cross-flow MCFC and SOFC stacks and graphs are presented showing temperature distributions. The `Smarter' stacks employ a high recycle rate resulting in a reduced natural gas concentration at the stack inlet, and this reduces or eliminates the unfavourable temperature dip. Catalyst grading can further improve the temperature distribution. The concept allows simple system configurations in which the need for fuel pre-heat is eliminated. Efficiencies are up to 10 percentage points higher than for conventional stacks with the same cell area and maximum stack temperature. The concept presented here was devised in a project part-funded by the EU, and has been adopted by the European Advanced DIR-MCFC development programme led by BCN.

  19. Status of Slip Stacking at Fermilab Main Injector

    CERN Document Server

    Seiya, Kiyomi; Chase, Brian; Dey, Joseph; Kourbanis, Ioanis; MacLachlan, James A; Meisner, Keith G; Pasquinelli, Ralph J; Reid, John; Rivetta, Claudio H; Steimel, Jim

    2005-01-01

    In order to increase proton intensity on anti proton production cycle of the Main Injector we are going to use the technique of 'slip stacking' and doing machine studies. In slip stacking, one bunch train is injected at slightly lower energy and second train is at slightly higher energy. Afterwards they are aligned longitudinally and captured with one rf bucket. This longitudinal stacking process is expected to double the bunch intensity. The required intensity for anti proton production is 8·1012

  20. Development of the electric utility dispersed use PAFC stack

    Energy Technology Data Exchange (ETDEWEB)

    Horiuchi, Hiroshi; Kotani, Ikuo [Mitsubishi Electric Co., Kobe (Japan); Morotomi, Isamu [Kansai Electric Power Co., Hyogo (Japan)] [and others

    1996-12-31

    Kansai Electric Power Co. and Mitsubishi Electric Co. have been developing the electric utility dispersed use PAFC stack operated under the ambient pressure. The new cell design have been developed, so that the large scale cell (1 m{sup 2} size) was adopted for the stack. To confirm the performance and the stability of the 1 m{sup 2} scale cell design, the short stack study had been performed.

  1. Method for monitoring stack gases for uranium activity

    International Nuclear Information System (INIS)

    Beverly, C.R.; Ernstberger, H.G.

    1988-01-01

    A method for sampling stack gases emanating from the purge cascade of a gaseous diffusion cascade system utilized to enrich uranium for determining the presence and extent of uranium in the stack gases in the form of gaseous uranium hexafluoride, is described comprising the steps of removing a side stream of gases from the stack gases, contacting the side stream of the stack gases with a stream of air sufficiently saturated with moisture for reacting with and converting any gaseous uranium hexafluroide contracted thereby in the side stream of stack gases to particulate uranyl fluoride. Thereafter contacting the side stream of stack gases containing the particulate uranyl fluoride with moving filter means for continuously intercepting and conveying the intercepted particulate uranyl fluoride away from the side stream of stack gases, and continually scanning the moving filter means with radiation monitoring means for sensing the presence and extent of particulate uranyl fluoride on the moving filter means which is indicative of the extent of particulate uranyl fluoride in the side stream of stack gases which in turn is indicative of the presence and extent of uranium hexafluoride in the stack gases

  2. Design and development of an automated uranium pellet stacking system

    International Nuclear Information System (INIS)

    Reiss, B.S.; Nokleby, S.B.

    2010-01-01

    A novel design for an automated uranium pellet stacking system is presented. This system is designed as a drop-in solution to the current production line to enhance the fuel pellet stacking process. The three main goals of this system are to reduce worker exposure to radiation to as low as reasonable achievable (ALARA), improve product quality, and increase productivity. The proposed system will reduce the potential for human error. This single automated system will replace the two existing pellet stacking stations while increasing the total output, eliminating pellet stacking as a bottleneck in the fuel bundle assembly process. (author)

  3. Highly Efficient, Durable Regenerative Solid Oxide Stack, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Precision Combustion, Inc. (PCI) proposes to develop a highly efficient regenerative solid oxide stack design. Novel structural elements allow direct internal...

  4. Experts’ Misinterpretation of Box Plots – a Dual Processing Approach

    Directory of Open Access Journals (Sweden)

    Stephanie Lem

    2014-11-01

    Full Text Available Recent studies have shown that students often misinterpret the area of the box in box plots as representing the frequency or proportion of observations in that interval, while it actually represents density. This misinterpretation has been shown to be based on the saliency of this area and can be explained by heuristic reasoning as defined by dual process theories. In this study we tested whether expert users of box plots also display this misinterpretation and show signs of the same heuristic reasoning as found in students. Using a reaction time test, we found signs of heuristic reasoning in experts, both with respect to accuracy and reaction times. If even experts have difficulty interpreting box plots, one can question whether these are an appropriate form of representation to use when reporting data and deserve the prominent place they currently have in the statistics curriculum.

  5. Graphical interpretation of confidence curves in rankit plots

    DEFF Research Database (Denmark)

    Hyltoft Petersen, Per; Blaabjerg, Ole; Andersen, Marianne

    2004-01-01

    distribution and the percentage of cumulative points exceeding these limits. The process is to rank the reference values and plot the cumulative frequency points in a rankit plot with a logarithmic (In=log(e)) transformed abscissa. If the distribution is close to In-Gaussian the cumulative frequency points......-Gaussian distributions of subgroups of reference values from healthy individuals is presented. In addition, distributions of values from well-defined diseased individuals may show up as In-Gaussian. It is evident from the examples that the rankit transformation and simple graphical evaluation for non......A well-known transformation from the bell-shaped Gaussian (normal) curve to a straight line in the rankit plot is investigated, and a tool for evaluation of the distribution of reference groups is presented. It is based on the confidence intervals for percentiles of the calculated Gaussian...

  6. On the Nature of Earth-Mars Porkchop Plots

    Science.gov (United States)

    Woolley, Ryan C.; Whetsel, Charles W.

    2013-01-01

    Porkchop plots are a quick and convenient tool to help mission designers plan ballistic trajectories between two bodies. Parameter contours give rise to the familiar 'porkchop' shape. Each synodic period the pattern repeats, but not exactly, primarily due to differences in inclination and non-zero eccentricity. In this paper we examine the morphological features of Earth-to-Mars porkchop plots and the orbital characteristics that create them. These results are compared to idealistic and optimized transfers. Conclusions are drawn about 'good' opportunities versus 'bad' opportunities for different mission applications.

  7. Split-plot Experiments with Unusual Numbers of Subplot Runs

    DEFF Research Database (Denmark)

    Kulahci, Murat

    2007-01-01

    In many experimental situations, it may not be feasible or even possible to run experiments in a completely randomized fashion as usually recommended. Under these circumstances, split-plot experiments in which certain factors are changed less frequently than the others are often used. Most...... of the literature on split-plot designs is based on 2-level factorials. For those designs, the number of subplots is a power of 2. There may however be some situations where for cost purposes or physical constraints, we may need to have unusual number of subplots such as 3, 5, 6, etc. In this article, we explore...

  8. Program PLOTTAB. (Version 87-2). General plotting program to plot any combination of continuous curves and/or discrete points (with associated error bars)

    International Nuclear Information System (INIS)

    Cullen, D.E.

    1987-06-01

    This program is designed to be a general application independent plotting program to plot any combination of continuous curves and/or discrete points (with associated error bars) using user supplied titles and x and y axis labels and units. Using this method the program has no idea what data is being plotted and yet the user can produce any number of plots with each plot properly identified. This program is available upon request costfree from the IAEA Nuclear Data Section. (author)

  9. PlotXY: A High Quality Plotting System for the Herschel Interactive Processing Environment (HIPE) and the Astronomical Community

    Science.gov (United States)

    Panuzzo, P.; Li, J.; Caux, E.

    2012-09-01

    The Herschel Interactive Processing Environment (HIPE) was developed by the European Space Agency (ESA) in collaboration with NASA and the Herschel Instrument Control Centres, to provide the astronomical community a complete environment to process and analyze the data gathered by the Herschel Space Observatory. One of the most important components of HIPE is the plotting system (named PlotXY) that we present here. With PlotXY it is possible to produce easily high quality publication-ready 2D plots. It provides a long list of features, with fully configurable components, and interactive zooming. The entire code of HIPE is written in Java and is open source released under the GNU Lesser General Public License version 3. A new version of PlotXY is being developed to be independent from the HIPE code base; it is available to the software development community for the inclusion in other projects at the URL google.com/p/jplot2d/'>http://code.google.com/p/jplot2d/.

  10. Manifold seal structure for fuel cell stack

    Science.gov (United States)

    Collins, William P.

    1988-01-01

    The seal between the sides of a fuel cell stack and the gas manifolds is improved by adding a mechanical interlock between the adhesive sealing strip and the abutting surface of the manifolds. The adhesive is a material which can flow to some extent when under compression, and the mechanical interlock is formed providing small openings in the portion of the manifold which abuts the adhesive strip. When the manifolds are pressed against the adhesive strips, the latter will flow into and through the manifold openings to form buttons or ribs which mechanically interlock with the manifolds. These buttons or ribs increase the bond between the manifolds and adhesive, which previously relied solely on the adhesive nature of the adhesive.

  11. Directive Stacked Patch Antenna for UWB Applications

    Directory of Open Access Journals (Sweden)

    Sharif I. Mitu Sheikh

    2013-01-01

    Full Text Available Directional ultrawideband (UWB antennas are popular in wireless signal-tracking and body-area networks. This paper presents a stacked microstrip antenna with an ultrawide impedance bandwidth of 114%, implemented by introducing defects on the radiating patches and the ground plane. The compact (20×34 mm antenna exhibits a directive radiation patterns for all frequencies of the 3–10.6 GHz band. The optimized reflection response and the radiation pattern are experimentally verified. The designed UWB antenna is used to maximize the received power of a software-defined radio (SDR platform. For an ultrawideband impulse radio system, this class of antennas is essential to improve the performance of the communication channels.

  12. ATLAS software stack on ARM64

    Science.gov (United States)

    Smith, Joshua Wyatt; Stewart, Graeme A.; Seuster, Rolf; Quadt, Arnulf; ATLAS Collaboration

    2017-10-01

    This paper reports on the port of the ATLAS software stack onto new prototype ARM64 servers. This included building the “external” packages that the ATLAS software relies on. Patches were needed to introduce this new architecture into the build as well as patches that correct for platform specific code that caused failures on non-x86 architectures. These patches were applied such that porting to further platforms will need no or only very little adjustments. A few additional modifications were needed to account for the different operating system, Ubuntu instead of Scientific Linux 6 / CentOS7. Selected results from the validation of the physics outputs on these ARM 64-bit servers will be shown. CPU, memory and IO intensive benchmarks using ATLAS specific environment and infrastructure have been performed, with a particular emphasis on the performance vs. energy consumption.

  13. ATLAS software stack on ARM64

    CERN Document Server

    AUTHOR|(INSPIRE)INSPIRE-00529764; The ATLAS collaboration; Stewart, Graeme; Seuster, Rolf; Quadt, Arnulf

    2017-01-01

    This paper reports on the port of the ATLAS software stack onto new prototype ARM64 servers. This included building the “external” packages that the ATLAS software relies on. Patches were needed to introduce this new architecture into the build as well as patches that correct for platform specific code that caused failures on non-x86 architectures. These patches were applied such that porting to further platforms will need no or only very little adjustments. A few additional modifications were needed to account for the different operating system, Ubuntu instead of Scientific Linux 6 / CentOS7. Selected results from the validation of the physics outputs on these ARM 64-bit servers will be shown. CPU, memory and IO intensive benchmarks using ATLAS specific environment and infrastructure have been performed, with a particular emphasis on the performance vs. energy consumption.

  14. Stacked generalization: an introduction to super learning.

    Science.gov (United States)

    Naimi, Ashley I; Balzer, Laura B

    2018-04-10

    Stacked generalization is an ensemble method that allows researchers to combine several different prediction algorithms into one. Since its introduction in the early 1990s, the method has evolved several times into a host of methods among which is the "Super Learner". Super Learner uses V-fold cross-validation to build the optimal weighted combination of predictions from a library of candidate algorithms. Optimality is defined by a user-specified objective function, such as minimizing mean squared error or maximizing the area under the receiver operating characteristic curve. Although relatively simple in nature, use of Super Learner by epidemiologists has been hampered by limitations in understanding conceptual and technical details. We work step-by-step through two examples to illustrate concepts and address common concerns.

  15. Determination of the stacking fault energies of face centured cubic metals and alloys by X-rays diffraction

    International Nuclear Information System (INIS)

    Borges, J.F.A.; Padilha, A.F.; Imakuma, K.

    1988-03-01

    An X-rays diffraction method was applied to measure the Stacking Fault Energies (SFE) of the AISI 304, AISI 316, AISI 347 and DIN-WERKSTOFF 1.4970 Austenitic Stainless Steels. The SFE determination plays an important role in the research of the mecanichal behaviour of the Metal and Alloys, their deformation mechanisms, stability of micro-structure and electronic configuration. The method is based on the relationship between the SFE and the ratio of the Mean Square Strains to the Stacking-Fault probability. The Mean Square Strain was evaluated by Fourier Analysis of X-rays Diffaction profiles, corrected to reduce instrumental effects, followed by the application of the Warren-Averbach method to the Fourier Coefficients. The Stacking-Fault probabilities were derived from the changes of peak separations between cold-worked and annealed specimens. (author) [pt

  16. Actuators Using Piezoelectric Stacks and Displacement Enhancers

    Science.gov (United States)

    Bar-Cohen, Yoseph; Sherrit, Stewart; Bao, Xiaoqi; Badescu, Mircea; Lee, Hyeong Jae; Walkenmeyer, Phillip; Lih, Shyh-Shiuh

    2015-01-01

    Actuators are used to drive all active mechanisms including machines, robots, and manipulators to name a few. The actuators are responsible for moving, manipulating, displacing, pushing and executing any action that is needed by the mechanism. There are many types and principles of actuation that are responsible for these movements ranging from electromagnetic, electroactive, thermo-mechanic, piezoelectric, electrostrictive etc. Actuators are readily available from commercial producers but there is a great need for reducing their size, increasing their efficiency and reducing their weight. Studies at JPL’s Non Destructive Evaluation and Advanced Actuators (NDEAA) Laboratory have been focused on the use of piezoelectric stacks and novel designs taking advantage of piezoelectric’s potential to provide high torque/force density actuation and high electromechanical conversion efficiency. The actuators/motors that have been developed and reviewed in this paper are operated by various horn configurations as well as the use of pre-stress flexures that make them thermally stable and increases their coupling efficiency. The use of monolithic designs that pre-stress the piezoelectric stack eliminates the use of compression stress bolt. These designs enable the embedding of developed solid-state motors/actuators in any structure with the only macroscopically moving parts are the rotor or the linear translator. Finite element modeling and design tools were used to determine the requirements and operation parameters and the results were used to simulate, design and fabricate novel actuators/motors. The developed actuators and performance will be described and discussed in this paper.

  17. A Conductive Gel for the Plotting of Equipotential Lines

    Science.gov (United States)

    Elizalde-Torres, J.; González-Cardel, M.; Vega-Murguía, E. J.; Castillo-González, I.; Rodríguez-Nava, M.

    2015-01-01

    This paper presents the development of a conductive gel that can be used to measure the electrical potential differences on its surface, and has enough consistency to plot equipotential lines. It has a gelation time of less than 10 min, and is suitable for implementing learning experiences in a physics teaching laboratory in a 90 min session. To…

  18. Analysis of Truck Downtimes Using Log Dispersion Plot | Temeng ...

    African Journals Online (AJOL)

    This paper uses log dispersion plot to analyse downtimes of a fleet of 22 dump trucks from the. Nchanga Open Pit, Zambia over a period of two months. Downtimes were categorised into breakdown codes to determine which ones were acute, chronic or a combination of both. The breakdown codes which were critical to the ...

  19. Box-and-Whisker Plots Applied to Food Chemistry

    Science.gov (United States)

    Ferreira, Joao E. V.; Miranda, Ricardo M.; Figueiredo, Antonio F.; Barbosa, Jardel P.; Brasil, Edykarlos M.

    2016-01-01

    Box-and-whisker plots or simply boxplots are powerful graphical representations that give an overview of a data set. In this work five different examples illustrate the applications of boxplots in food chemistry. The examples involve relative sweetness of sugars and sugar alcohols with respect to sucrose, the potassium content of fruits and…

  20. Estimation of Optimal Size of Plots for Experiments with Radiometer ...

    African Journals Online (AJOL)

    The objective of this study was to estimate the optimal size of plots for reflectance measurements in beans by the modified maximum curvature method and the maximum distance method. Reflectance readings were made on bean plants with the aid of the GreenSeeker® equipment, obtaining basic units of 0.45 m² in an ...

  1. Tracking forest resource condition through Permanent sample plots ...

    African Journals Online (AJOL)

    After decades of decentralized forest management in Tanzania, few scientific studies exist that provide baseline information on forest resources condition and eventual impact of decentralization policy. This paper presents efforts by Tanzania Forestry Research Institute (TAFORI) to establish Permanent Sample Plots (PSPs) ...

  2. Constructing General Orthogonal Fractional Factorial Split-Plot Designs

    NARCIS (Netherlands)

    Sartono, B.; Goos, P.; Schoen, E.

    2015-01-01

    While the orthogonal design of split-plot fractional factorial experiments has received much attention already, there are still major voids in the literature. First, designs with one or more factors acting at more than two levels have not yet been considered. Second, published work on nonregular

  3. Surveillance of Site A and Plot M report for 2010.

    Energy Technology Data Exchange (ETDEWEB)

    Golchert, N. W. (ESQ)

    2011-05-31

    The results of the environmental surveillance program conducted at Site A/Plot M in the Palos Forest Preserve area for Calendar Year 2010 are presented. Based on the results of the 1976-1978 radiological characterization of the site, a determination was made that a surveillance program be established. The characterization study determined that very low levels of hydrogen-3 (as tritiated water) had migrated from the burial ground and were present in two nearby hand-pumped picnic wells. The current surveillance program began in 1980 and consists of sample collection and analysis of surface and subsurface water. The results of the analyses are used to monitor the migration pathway of hydrogen-3 contaminated water from the burial ground (Plot M) to the hand-pumped picnic wells and monitor for the presence of radioactive materials in the environment of the area. Hydrogen-3 in the Red Gate Woods picnic wells was still detected this year, but the average and maximum concentrations were significantly less than found earlier. Hydrogen-3 continues to be detected in a number of wells, boreholes, dolomite holes, and a surface stream. Analyses since 1984 have indicated the presence of low levels of strontium-90 in water from a number of boreholes next to Plot M. The results of the surveillance program continue to indicate that the radioactivity remaining at Site A/Plot M does not endanger the health or safety of the public visiting the site, using the picnic area, or living in the vicinity.

  4. Surveillance of Site A and Plot M, Report for 2009.

    Energy Technology Data Exchange (ETDEWEB)

    Golchert, N. W.

    2010-04-21

    The results of the environmental surveillance program conducted at Site A/Plot M in the Palos Forest Preserve area for Calendar Year 2009 are presented. Based on the results of the 1976-1978 radiological characterization of the site, a determination was made that a surveillance program be established. The characterization study determined that very low levels of hydrogen-3 (as tritiated water) had migrated from the burial ground and were present in two nearby hand-pumped picnic wells. The current surveillance program began in 1980 and consists of sample collection and analysis of surface and subsurface water. The results of the analyses are used to monitor the migration pathway of hydrogen-3 contaminated water from the burial ground (Plot M) to the hand-pumped picnic wells and monitor for the presence of radioactive materials in the environment of the area. Hydrogen-3 in the Red Gate Woods picnic wells was still detected this year, but the average and maximum concentrations were significantly less than found earlier. Hydrogen-3 continues to be detected in a number of wells, boreholes, dolomite holes, and a surface stream. Analyses since 1984 have indicated the presence of low levels of strontium-90 in water from a number of boreholes next to Plot M. The results of the surveillance program continue to indicate that the radioactivity remaining at Site A/Plot M does not endanger the health or safety of the public visiting the site, using the picnic area, or living in the vicinity.

  5. A translog stochastic frontier analysis of plot size and cost ...

    African Journals Online (AJOL)

    There is need for policies aimed at encouraging the youths who are agile and stronger as well as the experienced to increase production. Land re-distribution policies are advocated to make lands available to the small-holder farmers who form the bulk of the farming population. Keywords: Translog stochastic frontier, plot ...

  6. Omitted Variable Sensitivity Analysis with the Annotated Love Plot

    Science.gov (United States)

    Hansen, Ben B.; Fredrickson, Mark M.

    2014-01-01

    The goal of this research is to make sensitivity analysis accessible not only to empirical researchers but also to the various stakeholders for whom educational evaluations are conducted. To do this it derives anchors for the omitted variable (OV)-program participation association intrinsically, using the Love plot to present a wide range of…

  7. Non-parametric and least squares Langley plot methods

    Science.gov (United States)

    Kiedron, P. W.; Michalsky, J. J.

    2016-01-01

    Langley plots are used to calibrate sun radiometers primarily for the measurement of the aerosol component of the atmosphere that attenuates (scatters and absorbs) incoming direct solar radiation. In principle, the calibration of a sun radiometer is a straightforward application of the Bouguer-Lambert-Beer law V = V0e-τ ṡ m, where a plot of ln(V) voltage vs. m air mass yields a straight line with intercept ln(V0). This ln(V0) subsequently can be used to solve for τ for any measurement of V and calculation of m. This calibration works well on some high mountain sites, but the application of the Langley plot calibration technique is more complicated at other, more interesting, locales. This paper is concerned with ferreting out calibrations at difficult sites and examining and comparing a number of conventional and non-conventional methods for obtaining successful Langley plots. The 11 techniques discussed indicate that both least squares and various non-parametric techniques produce satisfactory calibrations with no significant differences among them when the time series of ln(V0)'s are smoothed and interpolated with median and mean moving window filters.

  8. Infrared heater arrays for warming grazingland field plots

    Science.gov (United States)

    In order to study the likely effects of global warming on rangeland and other ecosystems in the future, we developed arrays of infrared heaters that can produce uniform warming across 3-m-diameter field plots. The efficiency of the heaters was higher than that of the heaters used in most previous in...

  9. A precision nutrient variability study of an experimental plot in ...

    African Journals Online (AJOL)

    The spatial soil fertility status of a 2.5 ha experimental plot was generated by mapping the soil nutrient concentration and fertility status using GIS kriging technique. The research was conducted in Mukono Zonal Agricultural Research and Development Institute, Mukono, Uganda in October 2013. Soil samples across the ...

  10. Designing fractional factorial split-plot experiments using integer programming

    DEFF Research Database (Denmark)

    Capehart, Shay R.; Keha, Ahmet; Kulahci, Murat

    2011-01-01

    factorial (FF) design, with the restricted randomisation structure to account for the whole plots and subplots. We discuss the formulation of FFSP designs using integer programming (IP) to achieve various design criteria. We specifically look at the maximum number of clear two-factor interactions...

  11. Efficiency of inventory plot patterns in quantitative analysis of ...

    African Journals Online (AJOL)

    Each 1 ha plot was divided into 100 quadrats of 100 m2 each and diameter at breast height (dbh) of trees was recorded in each quadrat. The required time to ... It is concluded that use of standard sample sizes will help to harmonise a forestry database and to carry out comparisons at regional level. Keywords: efficiency ...

  12. RCircos: an R package for Circos 2D track plots.

    Science.gov (United States)

    Zhang, Hongen; Meltzer, Paul; Davis, Sean

    2013-08-10

    Circos is a Perl language based software package for visualizing similarities and differences of genome structure and positional relationships between genomic intervals. Running Circos requires extra data processing procedures to prepare plot data files and configure files from datasets, which limits its capability of integrating directly with other software tools such as R. Recently published R Bioconductor package ggbio provides a function to display genomic data in circular layout based on multiple other packages, which increases its complexity of usage and decreased the flexibility in integrating with other R pipelines. We implemented an R package, RCircos, using only R packages that come with R base installation. The package supports Circos 2D data track plots such as scatter, line, histogram, heatmap, tile, connectors, links, and text labels. Each plot is implemented with a specific function and input data for all functions are data frames which can be objects read from text files or generated with other R pipelines. RCircos package provides a simple and flexible way to make Circos 2D track plots with R and could be easily integrated into other R data processing and graphic manipulation pipelines for presenting large-scale multi-sample genomic research data. It can also serve as a base tool to generate complex Circos images.

  13. The Brazilian national system of forest permanent plots

    Science.gov (United States)

    Yeda Maria Malheiros de Oliveira; Maria Augusta Doetzer Rosot; Patricia Povoa de Mottos; Joberto Veloso de Freitas; Guilherme Luis Augusto Gomide; < i> et al< /i>

    2009-01-01

    The Brazilian National System of Forest Permanent Plots (SisPP) is a governmental initiative designed and being implemented in partnership by the Ministry of Environment (MMA), represented by the National Forest Programme (PNF) and the Brazilian Forest Service (SFB) and the Embrapa Forestry (a research center of the Brazilian Agricultural Research Corporation - Embrapa...

  14. Simultaneous stack-gas scrubbing and waste water treatment

    Science.gov (United States)

    Poradek, J. C.; Collins, D. D.

    1980-01-01

    Simultaneous treatment of wastewater and S02-laden stack gas make both treatments more efficient and economical. According to results of preliminary tests, solution generated by stack gas scrubbing cycle reduces bacterial content of wastewater. Both processess benefit by sharing concentrations of iron.

  15. A Software Managed Stack Cache for Real-Time Systems

    DEFF Research Database (Denmark)

    Jordan, Alexander; Abbaspourseyedi, Sahar; Schoeberl, Martin

    2016-01-01

    In a real-time system, the use of a scratchpad memory can mitigate the difficulties related to analyzing data caches, whose behavior is inherently hard to predict. We propose to use a scratchpad memory for stack allocated data. While statically allocating stack frames for individual functions to ...

  16. Calculation of AC losses in large HTS stacks and coils

    DEFF Research Database (Denmark)

    Zermeno, Victor; Abrahamsen, Asger Bech; Mijatovic, Nenad

    2012-01-01

    In this work, we present a homogenization method to model a stack of HTS tapes under AC applied transport current or magnetic field. The idea is to find an anisotropic bulk equivalent for the stack of tapes, where the internal alternating structures of insulating, metallic, superconducting and su...

  17. Efficient Context Switching for the Stack Cache: Implementation and Analysis

    DEFF Research Database (Denmark)

    Abbaspourseyedi, Sahar; Brandner, Florian; Naji, Amine

    2015-01-01

    , the analysis of the stack cache was limited to individual tasks, ignoring aspects related to multitasking. A major drawback of the original stack cache design is that, due to its simplicity, it cannot hold the data of multiple tasks at the same time. Consequently, the entire cache content needs to be saved...

  18. Surveillance of Site A and Plot M report for 1991

    Energy Technology Data Exchange (ETDEWEB)

    Golchert, N.W.

    1992-05-01

    The results of the environmental surveillance program conducted at Site A/Plot M in the Palos Forest Preserve area for CY 1991 are presented. The surveillance program is the ongoing remedial action that resulted from the 1976--1978 radiological characterization of the site. That study determined that very low levels of hydrogen-3 (as tritiated water) had migrated from the burial ground and were present in two nearby hand-pumped picnic wells. The current program consists of sample collection and analysis of air, surface and subsurface water, and bottom sediment. The results of the analyses are used to (1) determine the migration pathway of water from the burial ground (Plot M) to the hand-pumped picnic wells, (2) establish if buried radionuclides other than hydrogen-3 have migrated, and (3) generally characterize the radiological environment of the area. Hydrogen-3 in the Red Gate Woods picnic wells was still detected this year, but the average and maximum concentrations were significantly less than found earlier. Tritiated water continues to be detected in a number of wells, boreholes, dolomite holes, and surface stream. For many years it was the only radionclide found to have migrated in measurable quantities. Analyses since 1984 have indicated the presence of low levels of strontium-90 in water from a number of borehole next to Plot M. The available data does not allow a firm conclusion as to whether the presence of this nuclide represents recent migration or movement that may have occurred before Plot M was capped. The results of the surveillance program continue to indicate that the radioactivity remaining at Site A/Plot M does not endanger the health or safety of the public visiting the site or those living in the vicinity.

  19. Dependency plots suggest the kinetic structure of ion channels.

    Science.gov (United States)

    Magleby, K L; Song, L

    1992-08-22

    Ion channels are integral membrane proteins that regulate ionic flux through cell membranes by opening and closing (gating) their pores. The gating can be monitored by observing step changes in the current flowing through single channels, and analysis of the observed open and closed interval durations has provided a window to develop kinetic models for the gating process. One difficulty in developing such models has been to determine the connections (transition pathways) among the various kinetic states involved in the gating. To help overcome this difficulty we present a transform (dependency plot) of the single-channel data that can give immediate insight into the connections. A dependency plot is derived by calculating a contingency table from a two-dimensional (joint density) dwell-time distribution of adjacent open and closed intervals by assuming that the two classified criteria are the open and closed durations of each pair of adjacent intervals. A three-dimensional surface plot of the fractional difference between the numbers of observed interval pairs and the numbers expected if the durations of adjacent intervals are independent then gives the dependency plot. An excess of interval pairs in the dependency plot suggests that the open and closed states (or compound states) that give rise to the interval pairs in excess are directly connected. A deficit of interval pairs suggests that the open and closed states (or compound states) that give rise to the interval pairs in deficit are either not directly connected or that there are additional open-closed transition pathways arising from the directly connected states.

  20. The behaviour of stacking fault energy upon interstitial alloying.

    Science.gov (United States)

    Lee, Jee-Yong; Koo, Yang Mo; Lu, Song; Vitos, Levente; Kwon, Se Kyun

    2017-09-11

    Stacking fault energy is one of key parameters for understanding the mechanical properties of face-centered cubic materials. It is well known that the plastic deformation mechanism is closely related to the size of stacking fault energy. Although alloying is a conventional method to modify the physical parameter, the underlying microscopic mechanisms are not yet clearly established. Here, we propose a simple model for determining the effect of interstitial alloying on the stacking fault energy. We derive a volumetric behaviour of stacking fault energy from the harmonic approximation to the energy-lattice curve and relate it to the contents of interstitials. The stacking fault energy is found to change linearly with the interstitial content in the usual low concentration domain. This is in good agreement with previously reported experimental and theoretical data.

  1. Dynamic Model of High Temperature PEM Fuel Cell Stack Temperature

    DEFF Research Database (Denmark)

    Andreasen, Søren Juhl; Kær, Søren Knudsen

    2007-01-01

    The present work involves the development of a model for predicting the dynamic temperature of a high temperature PEM (HTPEM) fuel cell stack. The model is developed to test different thermal control strategies before implementing them in the actual system. The test system consists of a prototype...... parts, where also the temperatures are measured. The heat balance of the system involves a fuel cell model to describe the heat added by the fuel cells when a current is drawn. Furthermore the model also predicts the temperatures, when heating the stack with external heating elements for start-up, heat...... the stack at a high stoichiometric air flow. This is possible because of the PBI fuel cell membranes used, and the very low pressure drop in the stack. The model consists of a discrete thermal model dividing the stack into three parts: inlet, middle and end and predicting the temperatures in these three...

  2. Direct methanol fuel cell stack based on MEMS technology

    Science.gov (United States)

    Zhang, Yufeng; Tang, Xiaochuan; Yuan, Zhenyu; Liu, Xiaowei

    2008-10-01

    This paper presents a design configuration of silicon-based micro direct methanol fuel cell (DMFC) stack in a planar array. The integrated series connection is oriented in a "flip-flop" configuration with electrical interconnections made by thin-film metal layers that coat the flow channels etched in the silicon substrate. The configuration features small connection space and low contact resistance. The MEMS fabrication process was utilized to fabricate the silicon plates of DMFC stack. This DMFC stack with an active area of 64mm x 11mm was characterized at room temperature and normal atmosphere. Experimental results show that the prototype stack is able to generate an open-circuit voltage of 2.7V and a maximum power density of 2.2mW/cm2, which demonstrate the feasibility of this new DMFC stack configuration.

  3. Deformation Induced Microtwins and Stacking Faults in Aluminum Single Crystal

    Science.gov (United States)

    Han, W. Z.; Cheng, G. M.; Li, S. X.; Wu, S. D.; Zhang, Z. F.

    2008-09-01

    Microtwins and stacking faults in plastically deformed aluminum single crystal were successfully observed by high-resolution transmission electron microscope. The occurrence of these microtwins and stacking faults is directly related to the specially designed crystallographic orientation, because they were not observed in pure aluminum single crystal or polycrystal before. Based on the new finding above, we propose a universal dislocation-based model to judge the preference or not for the nucleation of deformation twins and stacking faults in various face-centered-cubic metals in terms of the critical stress for dislocation glide or twinning by considering the intrinsic factors, such as stacking fault energy, crystallographic orientation, and grain size. The new finding of deformation induced microtwins and stacking faults in aluminum single crystal and the proposed model should be of interest to a broad community.

  4. Physical Sciences Laboratory 1 Rooftop Stack Mixing Study

    Energy Technology Data Exchange (ETDEWEB)

    Flaherty, Julia E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Antonio, Ernest J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-09-30

    To address concerns about worker exposures on the Physical Science Laboratory (PSL) rooftop, a tracer study was conducted to measure gaseous tracer concentrations downwind of six stacks on the southern half of the PSL building (PSL-1). These concerns were raised, in part, due to the non-standard configuration of the stacks on this building. Five of the six stacks were only about 8 feet tall, with one shorter stack that was essentially level with the roof deck. These stacks were reconfigured in August 2016, and these exhaust points on PSL-1 are now 18 feet tall. This report describes the objectives of the tracer tests performed on PSL-1, provides an overview of how the tests were executed, and presents results of the tests. The tests on the PSL rooftop were a follow-on project from a similar study performed on the LSL-II ventilation exhaust (Flaherty and Antonio, 2016).

  5. Preparation and characterization of porphyrin-polythiophene stacked films as prepared by electrochemical method under stirring condition

    International Nuclear Information System (INIS)

    Sugawa, Kosuke; Akiyama, Tsuyoshi; Yamada, Sunao

    2008-01-01

    Porphyrin-polythiophene (pTh) stacked films consisting of meso-tetrathienylporphyrin (TThP) and bithiophene (BiTh) were prepared on transparent indium-tin-oxide (ITO) electrodes by sequential electrochemical scanning of applied potential between 0 and + 2 V vs Ag wire in the electrolyte solution of BiTh and TThP under stirring condition. First, the pTh films were prepared by electrochemical polymerization and then TThP was incorporated into the as-prepared pTh film by subsequent electrochemical scanning as described above in the TThP solution. The operation of solution stirring during electrochemical scanning achieved the formation of robust stacked films. UV/Vis and fluorescence spectra confirmed that the amount of TThP moiety increased with increasing the number of electrochemical scanning cycles in the TThP solution. In order to evaluate the incorporation profile of TThP, surface analyses and depth profiles of stacked films were carried out by XPS spectroscopy. The results suggested that all films formed porphyrin-polythiophene stacked structure precisely, and that TThP was exclusively incorporated around the outermost region of the pTh film

  6. Reflector imaging by diffraction stacking with stacking velocity analysis; Jugo sokudo kaiseki wo tomonau sanran jugoho ni yoru hanshamen imaging

    Energy Technology Data Exchange (ETDEWEB)

    Matsushima, J.; Rokugawa, S.; Kato, Y. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Yokota, T. [Japan National Oil Corp., Tokyo (Japan); Miyazaki, T. [Geological Survey of Japan, Tsukuba (Japan)

    1997-10-22

    Concerning seismic reflection survey for geometrical arrangement between pits, the scattering stacking method with stacking velocity analysis is compared with the CDP (common depth point horizontal stacking method). The advantages of the CDP supposedly include the following. Since it presumes an average velocity field, it can determine velocities having stacking effects. The method presumes stratification and, since such enables the division of huge quantities of observed data into smaller groups, more data can be calculated in a shorter time period. The method has disadvantages, attributable to its presuming an average velocity field, that accuracy in processing is lower when the velocity field contrast is higher, that accuracy in processing is low unless stratification is employed, and that velocities obtained from stacking velocity analysis are affected by dipped structures. Such shortcomings may be remedied in the scattering stacking method with stacking velocity analysis. Possibilities are that, as far as the horizontal reflection plane is concerned, it may yield stack records higher in S/N ratio than the CDP. Findings relative to dipped reflection planes will be introduced at the presentation. 6 refs., 12 figs.

  7. A comparison of trenched plot techniques for partitioning soil respiration

    Energy Technology Data Exchange (ETDEWEB)

    Bond-Lamberty, Benjamin; Bronson, Dustin; Bladyka, Emma; Gower, Stith T.

    2011-07-16

    Partitioning the soil surface CO{sub 2} flux (R{sub S}) flux is an important step in understanding ecosystem-level carbon cycling, given that R{sub S} is poorly constrained and its source components may have different responses to climate change. Trenched plots are a classic method of separating the R{sub S} source fluxes, but labor-intensive and may cause considerable disturbance to the soil environment. This study tested if various methods of plant suppression in trenched plots affected R{sub S} fluxes, quantified the R{sub S} response to soil temperature and moisture changes, and estimated the heterotrophic contribution to R{sub S}. It was performed in a boreal black spruce (Picea mariana) plantation, using a complete randomized design, during the 2007 growing season (May-November). Trenched plots had significantly lower R{sub S} than control plots, with differences appearing {approx}100 days after trenching; spatial variability doubled after trenching but then declined throughout the experiment. Most trenching treatments had significantly lower (by {approx}0.5 {mu}mol m{sup -2} s{sup -1}) R{sub S} than the controls, and there was no significant difference in R{sub S} among the various trenching treatments. Soil temperature at 2 cm explained more R{sub S} variability than did 10-cm temperature or soil moisture. Temperature sensitivity (Q10) declined in the control plots from {approx}2.6 (at 5 C) to {approx}1.6 (at 15 C); trenched plots values were higher, from 3.1 at 5 C to 1.9 at 15 C. We estimated R{sub S} for the study period to be 241 {+-} 40 g C m{sup -2}, with roots contributing 64% of R{sub S} after accounting for fine root decay, and 293 g C m{sup -2} for the entire year. These findings suggest that laborious hand weeding of vegetation may be usefully replaced by other methods, easing future studies of this large and poorly-understood carbon flux.

  8. Black Hole Spectroscopy with Coherent Mode Stacking.

    Science.gov (United States)

    Yang, Huan; Yagi, Kent; Blackman, Jonathan; Lehner, Luis; Paschalidis, Vasileios; Pretorius, Frans; Yunes, Nicolás

    2017-04-21

    The measurement of multiple ringdown modes in gravitational waves from binary black hole mergers will allow for testing the fundamental properties of black holes in general relativity and to constrain modified theories of gravity. To enhance the ability of Advanced LIGO/Virgo to perform such tasks, we propose a coherent mode stacking method to search for a chosen target mode within a collection of multiple merger events. We first rescale each signal so that the target mode in each of them has the same frequency and then sum the waveforms constructively. A crucial element to realize this coherent superposition is to make use of a priori information extracted from the inspiral-merger phase of each event. To illustrate the method, we perform a study with simulated events targeting the ℓ=m=3 ringdown mode of the remnant black holes. We show that this method can significantly boost the signal-to-noise ratio of the collective target mode compared to that of the single loudest event. Using current estimates of merger rates, we show that it is likely that advanced-era detectors can measure this collective ringdown mode with one year of coincident data gathered at design sensitivity.

  9. Stacking faults in austempered ductile iron

    Energy Technology Data Exchange (ETDEWEB)

    Hermida, J.D. [CNEA, San Martin (Argentina). Dept. de Materiales

    1996-06-01

    During last decade, Austempered Ductile Iron (ADI) has been successfully used as an acceptable replacement material for steel in many applications, due to the relatively high strength and reasonable ductility obtained. These properties are the result of the special microstructure exhibited by this material at the end of the upper bainite reaction: ferrite platelets surrounded by high carbon stabilized austenite. However, at the beginning of the austempering treatment, the existence of interdendritic low carbon austenite is revealed by its transformation to martensite when cooling the sample or during subsequent deformation. The completion of the upper bainite reaction is of decisive importance to mechanical properties because the remaining martensite reduces ductility. It was observed that the rate of the upper bainite reaction is governed by the carbon content difference between the low and high carbon austenites. The carbon content is obtained by the lattice parameter measurement, because there exists a known expression that relates both magnitudes. Several works have used X-ray diffraction to measure the lattice parameter and phase concentrations as a function of austempering time. In these works, the lattice parameters were obtained directly from the {l_brace}220{r_brace} and {l_brace}311{r_brace} peaks position. The purpose of this work is to show more precise lattice parameters measurement and, very closely related to this, the existence of stacking faults in austenite, even at times within the processing window.

  10. ATLAS software stack on ARM64

    CERN Document Server

    Smith, Joshua Wyatt; The ATLAS collaboration

    2016-01-01

    The ATLAS experiment explores new hardware and software platforms that, in the future, may be more suited to its data intensive workloads. One such alternative hardware platform is the ARM architecture, which is designed to be extremely power efficient and is found in most smartphones and tablets. CERN openlab recently installed a small cluster of ARM 64-bit evaluation prototype servers. Each server is based on a single-socket ARM 64-bit system on a chip, with 32 Cortex-A57 cores. In total, each server has 128 GB RAM connected with four fast memory channels. This paper reports on the port of the ATLAS software stack onto these new prototype ARM64 servers. This included building the "external" packages that the ATLAS software relies on. Patches were needed to introduce this new architecture into the build as well as patches that correct for platform specific code that caused failures on non-x86 architectures. These patches were applied such that porting to further platforms will need no or only very little adj...

  11. Long Duration Balloon Charge Controller Stack Integration

    Science.gov (United States)

    Clifford, Kyle

    NASA and the Columbia Scientific Balloon Facility are interested in updating the design of the charge controller on their long duration balloon (LDB) in order to enable the charge controllers to be directly interfaced via RS232 serial communication by a ground testing computers and the balloon's flight computer without the need to have an external electronics stack. The design involves creating a board that will interface with the existing boards in the charge controller in order to receive telemetry from and send commands to those boards, and interface with a computer through serial communication. The inputs to the board are digital status inputs indicating things like whether the photovoltaic panels are connected or disconnected; and analog inputs with information such as the battery voltage and temperature. The outputs of the board are 100ms duration command pulses that will switch relays that do things like connect the photovoltaic panels. The main component of this design is a PIC microcontroller which translates the outputs of the existing charge controller into serial data when interrogated by a ground testing or flight computer. Other components involved in the design are an AD7888 12-bit analog to digital converter, a MAX3232 serial transceiver, various other ICs, capacitors, resistors, and connectors.

  12. Lithiation-induced shuffling of atomic stacks

    KAUST Repository

    Nie, Anmin

    2014-09-10

    In rechargeable lithium-ion batteries, understanding the atomic-scale mechanism of Li-induced structural evolution occurring at the host electrode materials provides essential knowledge for design of new high performance electrodes. Here, we report a new crystalline-crystalline phase transition mechanism in single-crystal Zn-Sb intermetallic nanowires upon lithiation. Using in situ transmission electron microscopy, we observed that stacks of atomic planes in an intermediate hexagonal (h-)LiZnSb phase are "shuffled" to accommodate the geometrical confinement stress arising from lamellar nanodomains intercalated by lithium ions. Such atomic rearrangement arises from the anisotropic lithium diffusion and is accompanied by appearance of partial dislocations. This transient structure mediates further phase transition from h-LiZnSb to cubic (c-)Li2ZnSb, which is associated with a nearly "zero-strain" coherent interface viewed along the [001]h/[111]c directions. This study provides new mechanistic insights into complex electrochemically driven crystalline-crystalline phase transitions in lithium-ion battery electrodes and represents a noble example of atomic-level structural and interfacial rearrangements.

  13. Weyl magnons in noncoplanar stacked kagome antiferromagnets

    Science.gov (United States)

    Owerre, S. A.

    2018-03-01

    Weyl nodes have been experimentally realized in photonic, electronic, and phononic crystals. However, magnonic Weyl nodes are yet to be seen experimentally. In this paper, we propose Weyl magnon nodes in noncoplanar stacked frustrated kagome antiferromagnets, naturally available in various real materials. Most crucially, the Weyl nodes in the current system occur at the lowest excitation and possess a topological thermal Hall effect, therefore they are experimentally accessible at low temperatures due to the population effect of bosonic quasiparticles. In stark contrast to other magnetic systems, the current Weyl nodes do not rely on time-reversal symmetry breaking by the magnetic order. Rather, they result from explicit macroscopically broken time reversal symmetry by the scalar spin chirality of noncoplanar spin textures and can be generalized to chiral spin liquid states. Moreover, the scalar spin chirality gives a real space Berry curvature which is not available in previously studied magnetic Weyl systems. We show the existence of magnon arc surface states connecting projected Weyl magnon nodes on the surface Brillouin zone. We also uncover the first realization of triply-degenerate nodal magnon point in the noncollinear regime with zero scalar spin chirality.

  14. Single point aerosol sampling: Evaluation of mixing and probe performance in a nuclear stack

    Energy Technology Data Exchange (ETDEWEB)

    Rodgers, J.C.; Fairchild, C.I.; Wood, G.O. [Los Alamos National Laboratory, NM (United States)] [and others

    1995-02-01

    Alternative Reference Methodologies (ARMs) have been developed for sampling of radionuclides from stacks and ducts that differ from the methods required by the U.S. EPA. The EPA methods are prescriptive in selection of sampling locations and in design of sampling probes whereas the alternative methods are performance driven. Tests were conducted in a stack at Los Alamos National Laboratory to demonstrate the efficacy of the ARMs. Coefficients of variation of the velocity tracer gas, and aerosol particle profiles were determined at three sampling locations. Results showed numerical criteria placed upon the coefficients of variation by the ARMs were met at sampling stations located 9 and 14 stack diameters from flow entrance, but not at a location that is 1.5 diameters downstream from the inlet. Experiments were conducted to characterize the transmission of 10 {mu}m aerodynamic equivalent diameter liquid aerosol particles through three types of sampling probes. The transmission ratio (ratio of aerosol concentration at the probe exit plane to the concentration in the free stream) was 107% for a 113 L/min (4-cfm) anisokinetic shrouded probe, but only 20% for an isokinetic probe that follows the EPA requirements. A specially designed isokinetic probe showed a transmission ratio of 63%. The shrouded probe performance would conform to the ARM criteria; however, the isokinetic probes would not.

  15. Control of interfacial properties of Pr-oxide/Ge gate stack structure by introduction of nitrogen

    Science.gov (United States)

    Kato, Kimihiko; Kondo, Hiroki; Sakashita, Mitsuo; Nakatsuka, Osamu; Zaima, Shigeaki

    2011-06-01

    We have demonstrated the control of interfacial properties of Pr-oxide/Ge gate stack structure by the introduction of nitrogen. From C- V characteristics of Al/Pr-oxide/Ge 3N 4/Ge MOS capacitors, the interface state density decreases without the change of the accumulation capacitance after annealing. The TEM and TED measurements reveal that the crystallization of Pr-oxide is enhanced with annealing and the columnar structure of cubic-Pr 2O 3 is formed after annealing. From the depth profiles measured using XPS with Ar sputtering for the Pr-oxide/Ge 3N 4/Ge stack structure, the increase in the Ge component is not observed in a Pr-oxide film and near the interface between a Pr-oxide film and a Ge substrate. In addition, the N component segregates near the interface region, amorphous Pr-oxynitride (PrON) is formed at the interface. As a result, Pr-oxide/PrON/Ge stacked structure without the Ge-oxynitride interlayer is formed.

  16. CADASTRAL CLASSIFICATION OF THE LAND PLOTS IN UKRAINE

    Directory of Open Access Journals (Sweden)

    KIRICHEK Yu. O.

    2016-04-01

    Full Text Available Summary. Work concerns development of national system of classification of the land plots. The developed classification will allow to solve correctly a number of the corresponding cadastral, land management, estimated and other tasks. The analysis of classifications of lands, improvements and real estate in general is made. The created offers concerning creation of a new classification of the land plots in Ukraine. Today the Ukrainian real estate market has no single system that separates the system property groups, classes and types. This significantly complicates the work and can not fully be aware of the specific situation of real estate market. This task is designed to solve classification properties, it is used to transition from a diversity of individual properties to a limited number of classes of evaluation objects. The classification is different functional purpose (use facilities assessment, which determines the difference in value.

  17. On a CP anisotropy measurement in the Dalitz plot

    International Nuclear Information System (INIS)

    Bediaga, I.; Gomes, A.; Guerrer, G.; Miranda, J.; Reis, A. C. dos; Bigi, I. I.

    2009-01-01

    We describe a novel use of the Dalitz plot to probe CP symmetry in three-body modes of B and D mesons. It is based on an observable inspired by astronomers' practice, namely the significance in the difference between corresponding Dalitz plot bins. It provides a model-independent mapping of local CP asymmetries. We illustrate the method for probing CP symmetry in the two complementary cases of B and D decays: in the former sizable or even large effects can be expected, yet have to be differentiated against leading standard model contributions, while in the latter one cannot count on sizable effects, yet has to deal with much less standard model background.

  18. Volcano plots in hydrogen electrocatalysis - uses and abuses.

    Science.gov (United States)

    Quaino, Paola; Juarez, Fernanda; Santos, Elizabeth; Schmickler, Wolfgang

    2014-01-01

    Sabatier's principle suggests, that for hydrogen evolution a plot of the rate constant versus the hydrogen adsorption energy should result in a volcano, and several such plots have been presented in the literature. A thorough examination of the data shows, that there is no volcano once the oxide-covered metals are left out. We examine the factors that govern the reaction rate in the light of our own theory and conclude, that Sabatier's principle is only one of several factors that determine the rate. With the exception of nickel and cobalt, the reaction rate does not decrease for highly exothermic hydrogen adsorption as predicted, because the reaction passes through more suitable intermediate states. The case of nickel is given special attention; since it is a 3d metal, its orbitals are compact and the overlap with hydrogen is too low to make it a good catalyst.

  19. Volcano plots in hydrogen electrocatalysis – uses and abuses

    Science.gov (United States)

    Quaino, Paola; Juarez, Fernanda; Santos, Elizabeth

    2014-01-01

    Summary Sabatier’s principle suggests, that for hydrogen evolution a plot of the rate constant versus the hydrogen adsorption energy should result in a volcano, and several such plots have been presented in the literature. A thorough examination of the data shows, that there is no volcano once the oxide-covered metals are left out. We examine the factors that govern the reaction rate in the light of our own theory and conclude, that Sabatier’s principle is only one of several factors that determine the rate. With the exception of nickel and cobalt, the reaction rate does not decrease for highly exothermic hydrogen adsorption as predicted, because the reaction passes through more suitable intermediate states. The case of nickel is given special attention; since it is a 3d metal, its orbitals are compact and the overlap with hydrogen is too low to make it a good catalyst. PMID:24991521

  20. A user's guide of a plotting program PLTJOINT

    International Nuclear Information System (INIS)

    Sasaki, Makoto; Sato, Wakaei; Nakagawa, Masayuki; Mori, Takamasa

    1988-02-01

    A plotting program PLTJOINT is able to plot various types of input and output data from neutronics calculations with two dimensional coordinates. These data include cross sections, neutron flux or spectrum, reaction rate distribution and auxiliary data. These are read from the input and output files of the JOINT system and the transport code system using double differential form cross section, and from arbitrary BCD input file. General purpose option is also available. Much care is taken in lettering such as types of characters (italic, Greek letters and characters), super and subscript of alphabet and numeral. Users can design their own characters by using a program IGDRASIL. Most of input data can be read in free format. The code has been programed so flexibly that new functions can be easily added to. (author)

  1. [Murderers in white coats--the physicians' plot against Stalin].

    Science.gov (United States)

    Olsen, B

    1997-12-10

    During the Moscow trials in 1936-38 several doctors were sentenced for participating in the murders of party leaders. As others who were accused, the doctors willingly confessed to crimes they could not possibly have committed. A second doctors' plot took place in the autumn of 1952. This time nine doctors, six of them Jews, were arrested for the attempted murder of political leaders. Only the unexpected death of Josef Stalin prevented a new wave of terror. With the single exception of Genrikh Grigorjevitsj Jagoda (1891-1938), head of the NKVD (KGB's predecessor), all those sentenced under the Moscow process are now rehabilitated. The participants of the second doctors' plot were rehabilitated immediately after Stalin's death.

  2. Review article: The mountain motif in the plot of Matthew

    Directory of Open Access Journals (Sweden)

    Gert J. Volschenk

    2010-09-01

    Full Text Available This article reviewed T.L. Donaldson’s book, Jesus on the mountain: A study in Matthean theology, published in 1985 by JSOT Press, Sheffield, and focused on the mountain motif in the structure and plot of the Gospel of Matthew, in addition to the work of Donaldson on the mountain motif as a literary motif and as theological symbol. The mountain is a primary theological setting for Jesus’ ministry and thus is an important setting, serving as one of the literary devices by which Matthew structured and progressed his narrative. The Zion theological and eschatological significance and Second Temple Judaism serve as the historical and theological background for the mountain motif. The last mountain setting (Mt 28:16–20 is the culmination of the three theological themes in the plot of Matthew, namely Christology, ecclesiology and salvation history.

  3. [Eugenics, an element of the literary plots of dystopia].

    Science.gov (United States)

    Baum, Ewa; Musielak, Michał

    2007-01-01

    The work presents the ideas and assumptions of eugenics, a social philosophy established in 1883 by Francis Galton, which affected the social policies of numerous European countries in the first half of the 20th century. The work shows the effect of eugenics on the literary standards of European prose in the previous century. Two outstanding dystopian novels of the 20th century, The Brave New World by Aldous Huxley and 1984 by George Orwell, situate eugenics as a permanent element of the literary plot of dystopia. Apart from the typical features of this type of novel, for example: personal narration with a trace of irony, a totalitarian state and Newspeak, eugenics is an important element of the literary plot with is aim to exclude and marginalise certain social groups. Eugenics is also one of the main social ideas criticised by both the writers.

  4. Surveillance of site A and plot M, report for 2007.

    Energy Technology Data Exchange (ETDEWEB)

    Golchert, N. W.; ESH/QA Oversight

    2008-03-25

    The results of the environmental surveillance program conducted at Site A/Plot M in the Palos Forest Preserve area for Calendar Year 2007 are presented. Based on the results of the 1976-1978 radiological characterization of the site, a determination was made that a surveillance program be established. The characterization study determined that very low levels of hydrogen-3 (as tritiated water) had migrated from the burial ground and were present in two nearby hand pumped picnic wells. The current surveillance program began in 1980 and consists of sample collection and analysis of surface and subsurface water. The results of the analyses are used to: (1) monitor the migration pathway of water from the burial ground (Plot M) to the hand-pumped picnic wells, (2) establish if other buried radionuclides have migrated, and (3) monitor the presence of radioactive materials in the environment of the area. Hydrogen-3 in the Red Gate Woods picnic wells was still detected this year, but the average and maximum concentrations were significantly less than found earlier. Hydrogen-3 continues to be detected in a number of wells, boreholes, dolomite holes, and a surface stream. Analyses since 1984 have indicated the presence of low levels of strontium-90 in water from a number of boreholes next to Plot M. The results of the surveillance program continue to indicate that the radioactivity remaining at Site A/Plot M does not endanger the health or safety of the public visiting the site, using the picnic area, or living in the vicinity.

  5. Surveillance of Site A and Plot M, Report for 2008.

    Energy Technology Data Exchange (ETDEWEB)

    Golchert, N. W.

    2009-05-07

    The results of the environmental surveillance program conducted at Site A/Plot M in the Palos Forest Preserve area for Calendar Year 2008 are presented. Based on the results of the 1976-1978 radiological characterization of the site, a determination was made that a surveillance program be established. The characterization study determined that very low levels of hydrogen-3 (as tritiated water) had migrated from the burial ground and were present in two nearby hand pumped picnic wells. The current surveillance program began in 1980 and consists of sample collection and analysis of surface and subsurface water. The results of the analyses are used to (1) monitor the migration pathway of hydrogen-3 contaminated water from the burial ground (Plot M) to the hand-pumped picnic wells, (2) establish if other buried radionuclides have migrated, and (3) monitor for the presence of radioactive materials in the environment of the area. Hydrogen-3 in the Red Gate Woods picnic wells was still detected this year, but the average and maximum concentrations were significantly less than found earlier. Hydrogen-3 continues to be detected in a number of wells, boreholes, dolomite holes, and a surface stream. Analyses since 1984 have indicated the presence of low levels of strontium-90 in water from a number of boreholes next to Plot M. The results of the surveillance program continue to indicate that the radioactivity remaining at Site A/Plot M does not endanger the health or safety of the public visiting the site, using the picnic area, or living in the vicinity.

  6. Surveillance of Site A and Plot M - Report for 2006.

    Energy Technology Data Exchange (ETDEWEB)

    Golchert, N. W.; ESH/QA Oversight

    2007-05-07

    The results of the environmental surveillance program conducted at Site A/Plot M in the Palos Forest Preserve area for Calendar Year 2006 are presented. Based on the results of the 1976-1978 radiological characterization of the site, a determination was made that a surveillance program be established. The characterization study determined that very low levels of hydrogen-3 (as tritiated water) had migrated from the burial ground and were present in two nearby hand-pumped picnic wells. The current surveillance program began in 1980 and consists of sample collection and analysis of surface and subsurface water. The results of the analyses are used to (1) monitor the migration pathway of water from the burial ground (PlotM) to the hand pumped picnic wells, (2) establish if buried radionuclides other than hydrogen-3 have migrated, and (3) monitor the presence of radioactive and chemically hazardous materials in the environment of the area. Hydrogen-3 in the Red GateWoods picnic wells was still detected this year, but the average and maximum concentrations were significantly less than found earlier. Hydrogen-3 continues to be detected in a number of wells, boreholes, dolomite holes, and a surface stream. Analyses since 1984 have indicated the presence of low levels of strontium-90 in water from a number of boreholes next to Plot M. The results of the surveillance program continue to indicate that the radioactivity remaining at Site A/Plot M does not endanger the health or safety of the public visiting the site, using the picnic area, or living in the vicinity.

  7. Surveillance of Site A and Plot M - Report for 2005.

    Energy Technology Data Exchange (ETDEWEB)

    Golchert, N. W.; ESH/QA Oversight

    2006-04-10

    The results of the environmental surveillance program conducted at Site A/Plot M in the Palos Forest Preserve area for Calendar Year 2005 are presented. Based on the results of the 1976-1978 radiological characterization of the site, a determination was made that a surveillance program be established. The characterization study determined that very low levels of hydrogen-3 (as tritiated water) had migrated from the burial ground and were present in two nearby handpumped picnic wells. The current surveillance program began in 1980 and consists of sample collection and analysis of surface and subsurface water. The results of the analyses are used to (1) monitor the migration pathway of water from the burial ground (Plot M) to the handpumped picnic wells, (2) establish if buried radionuclides other than hydrogen-3 have migrated, and (3) monitor the presence of radioactive and chemically hazardous materials in the environment of the area. Hydrogen-3 in the Red Gate Woods picnic wells was still detected this year, but the average and maximum concentrations were significantly less than found earlier. Hydrogen-3 continues to be detected in a number of wells, boreholes, dolomite holes, and a surface stream. Analyses since 1984 have indicated the presence of low levels of strontium-90 in water from a number of boreholes next to Plot M. The results of the surveillance program continue to indicate that the radioactivity remaining at Site A/Plot M does not endanger the health or safety of the public visiting the site, using the picnic area, or living in the vicinity.

  8. Fisher.py: Fisher Matrix Manipulation and Confidence Contour Plotting

    Science.gov (United States)

    Coe, Dan

    2010-10-01

    Fisher.py allows you to combine constraints from multiple experiments (e.g., weak lensing + supernovae) and add priors (e.g., a flat universe) simply and easily. Calculate parameter uncertainties and plot confidence ellipses. Fisher matrix expectations for several experiments are included as calculated by myself (time delays) and the Dark Energy Task Force (WL/SN/BAO/CL/CMB), or provide your own.

  9. Loading and plotting of cortical surface representations in Nilearn

    Directory of Open Access Journals (Sweden)

    Julia Huntenburg

    2017-02-01

    Full Text Available Processing neuroimaging data on the cortical surface traditionally requires dedicated heavy-weight software suites. Here, we present an initial support of cortical surfaces in Python within the neuroimaging data processing toolbox Nilearn. We provide loading and plotting functions for different surface data formats with minimal dependencies, along with examples of their application. Limitations of the current implementation and potential next steps are discussed.

  10. The PLOT (Paleolimnological Transect) Project in the Russian Arctic

    Science.gov (United States)

    Gromig, R.; Andreev, A.; Baumer, M.; Bolshiyanov, D.; Fedorov, G.; Frolova, L.; Krastel, S.; Lebas, E.; Ludikova, A.; Melles, M.; Meyer, H.; Nazarova, L.; Pestryakova, L.; Savelieva, L.; Shumilovskikh, L.; Subetto, D.; Wagner, B.; Wennrich, V.

    2017-12-01

    The joint Russian- German project 'PLOT - Paleolimnological Transec' aims to recover lake sediment sequences along a >6000 km long longitudinal transect across the Eurasian Arctic in order to investigate the Late Quaternary climatic and environmental history. The climate history of the Arctic is of particular interest since it is the region, which is experiencing major impact of the current climate change. The project is funded for three years (2015-2018) by the Russian and German Ministries of Research. Since 2013 extensive fieldwork, including seismic surveys, coring, and hydrological investigations, was carried out at lakes Ladoga (NW Russia, pilot study), Bolshoye Shuchye (Polar Urals), Emanda (Verkhoyansk Range, field campaign planned for August 2017), Levinson-Lessing and Taymyr (Taymyr Peninsula). Fieldwork at lakes Bolshoye Shuchye, Levinson-Lessing and Taymyr was conducted in collaboration with the Russian-Norwegian CHASE (Climate History along the Arctic Seaboard of Eurasia) project. A major objective of the PLOT project was to recover preglacial sediments. A multiproxy approach was applied to the analytical work of all cores, including (bio-)geochemical, sedimentological, geophysical, and biological analyses. First data implies the presence of preglacial sediments in the cores from all lakes so far visited. Age-depth models, based on radiocarbon dating, OSL dating, paleomagnetic measurements, identification of cryptotephra, and varve counting (where applicable), are in progress. Climate variability in the records shall be compared to that recorded at Lake Eĺgygytgyn (NE Russia), which represents the master record for the Siberian Arctic. The outcome of the PLOT project will be a better understanding of the temporal and spatial variability and development of the Arctic climate. Here, we present the major results and first key interpretations of the PLOT project, along with an outlook on the future strategy and foci. First results from lakes Ladoga

  11. Looking at large data sets using binned data plots

    Energy Technology Data Exchange (ETDEWEB)

    Carr, D.B.

    1990-04-01

    This report addresses the monumental challenge of developing exploratory analysis methods for large data sets. The goals of the report are to increase awareness of large data sets problems and to contribute simple graphical methods that address some of the problems. The graphical methods focus on two- and three-dimensional data and common task such as finding outliers and tail structure, assessing central structure and comparing central structures. The methods handle large sample size problems through binning, incorporate information from statistical models and adapt image processing algorithms. Examples demonstrate the application of methods to a variety of publicly available large data sets. The most novel application addresses the too many plots to examine'' problem by using cognostics, computer guiding diagnostics, to prioritize plots. The particular application prioritizes views of computational fluid dynamics solution sets on the fly. That is, as each time step of a solution set is generated on a parallel processor the cognostics algorithms assess virtual plots based on the previous time step. Work in such areas is in its infancy and the examples suggest numerous challenges that remain. 35 refs., 15 figs.

  12. The value of building plots in Italy - pdf

    Directory of Open Access Journals (Sweden)

    Paolo Rosato

    2014-12-01

    Full Text Available This paper suggests some analysis on dynamics of building plots value in Italy. This is an important subject, since the study of changes in plots value in space and time enables the evaluation of urban rent, which is essential for a fair and effective planning. The analysis confirm past hypothesis which are well known to real estate market operators. The first resulting fact is that the changes in building plots value are concurrent to those in real estate value and the increase occurring in the last years is in relative terms higher than the past one. This seems to confirm that, during real estate market expansion, most of the increase of buildings’ value is attributable to the land rent. The second observation is about value dynamics over time: it has been observed that, during an expansion in demand, the value significantly increases in central areas, much more than in peripheral ones; this means that absolute rent arising from shortage in urban areas is higher than the differential rent created through urban expansion in peripheral areas. Finally, it was highlighted that the factors affecting the value in building areas play different roles, depending on their location relative to the urban centre, identifying differently structured market segments.

  13. Consolidity: Stack-based systems change pathway theory elaborated

    Directory of Open Access Journals (Sweden)

    Hassen Taher Dorrah

    2014-06-01

    Full Text Available This paper presents an elaborated analysis for investigating the stack-based layering processes during the systems change pathway. The system change pathway is defined as the path resulting from the combinations of all successive changes induced on the system when subjected to varying environments, activities, events, or any excessive internal or external influences and happenings “on and above” its normal stands, situations or set-points during its course of life. The analysis is essentially based on the important overall system paradigm of “Time driven-event driven-parameters change”. Based on this paradigm, it is considered that any affected activity, event or varying environment is intelligently self-recorded inside the system through an incremental consolidity-scaled change in system parameters of the stack-based layering types. Various joint stack-based mathematical and graphical approaches supported by representable case studies are suggested for the identification, extraction, and processing of various stack-based systems changes layering of different classifications and categorizations. Moreover, some selected real life illustrative applications are provided to demonstrate the (infinite stack-based identification and recognition of the change pathway process in the areas of geology, archeology, life sciences, ecology, environmental science, engineering, materials, medicine, biology, sociology, humanities, and other important fields. These case studies and selected applications revealed that there are general similarities of the stack-based layering structures and formations among all the various research fields. Such general similarities clearly demonstrate the global concept of the “fractals-general stacking behavior” of real life systems during their change pathways. Therefore, it is recommended that concentrated efforts should be expedited toward building generic modular stack-based systems or blocks for the mathematical

  14. Loop Entropy Assists Tertiary Order: Loopy Stabilization of Stacking Motifs

    Directory of Open Access Journals (Sweden)

    Daniel P. Aalberts

    2011-11-01

    Full Text Available The free energy of an RNA fold is a combination of favorable base pairing and stacking interactions competing with entropic costs of forming loops. Here we show how loop entropy, surprisingly, can promote tertiary order. A general formula for the free energy of forming multibranch and other RNA loops is derived with a polymer-physics based theory. We also derive a formula for the free energy of coaxial stacking in the context of a loop. Simulations support the analytic formulas. The effects of stacking of unpaired bases are also studied with simulations.

  15. Mixed Mechanism of Lubrication by Lipid Bilayer Stacks.

    Science.gov (United States)

    Boţan, Alexandru; Joly, Laurent; Fillot, Nicolas; Loison, Claire

    2015-11-10

    Although the key role of lipid bilayer stacks in biological lubrication is generally accepted, the mechanisms underlying their extreme efficiency remain elusive. In this article, we report molecular dynamics simulations of lipid bilayer stacks undergoing load and shear. When the hydration level is reduced, the velocity accommodation mechanism changes from viscous shear in hydration water to interlayer sliding in the bilayers. This enables stacks of hydrated lipid bilayers to act as efficient boundary lubricants for various hydration conditions, structures, and mechanical loads. We also propose an estimation for the friction coefficient; thanks to the strong hydration forces between lipid bilayers, the high local viscosity is not in contradiction with low friction coefficients.

  16. On $k$-stellated and $k$-stacked spheres

    OpenAIRE

    Bagchi, Bhaskar; Datta, Basudeb

    2012-01-01

    We introduce the class $\\Sigma_k(d)$ of $k$-stellated (combinatorial) spheres of dimension $d$ ($0 \\leq k \\leq d + 1$) and compare and contrast it with the class ${\\cal S}_k(d)$ ($0 \\leq k \\leq d$) of $k$-stacked homology $d$-spheres. We have $\\Sigma_1(d) = {\\cal S}_1(d)$, and $\\Sigma_k(d) \\subseteq {\\cal S}_k(d)$ for $d \\geq 2k - 1$. However, for each $k \\geq 2$ there are $k$-stacked spheres which are not $k$-stellated. The existence of $k$-stellated spheres which are not $k$-stacked remains...

  17. Stacking by electroinjection with discontinuous buffers in capillary zone electrophoresis.

    Science.gov (United States)

    Shihabi, Zak K

    2002-08-01

    The work presented here demonstrates that electroinjection can be performed using discontinuous buffers, which can result in better stacking than that obtained by hydrodynamic injection. The sample can be concentrated at the tip of the capillary leaving practically the whole capillary for sample separation. This results in several advantages, such as better sample concentration, higher plate number and shorter time of stacking. However, sample introduction by electromigration is suited for samples free or low in salt content. Samples, which are high in salt content, are better introduced by the hydrodynamic injection for stacking by the discontinuous buffers. Different simple methods to introduce the discontinuity in the buffer for electroinjection are discussed.

  18. Optimized stacked RADFETs for milli-rad dose measurement

    International Nuclear Information System (INIS)

    O'Connell, B.; Lane, B.; Mohammadzadeh, A.

    1999-01-01

    This paper details the improvements in the design of stacked RADFETs for increased radiation sensitivity. The issues of high read-out voltage has been shown to be a draw-back. It is the body (bulk)effect factor that is responsible for the increased overall stack Threshold voltage (V T ), which is greater than the sum of the individual devices V T . From extensive process and device simulation and resultant circuit simulation, modified stack structures have been proposed and designed. New and exciting result of lower initial (pre-irradiation) output voltage as well as increased radiation sensitivity will be presented. (author)

  19. Plot and Personification in “Tehran-e- Makhuf“

    Directory of Open Access Journals (Sweden)

    M. Pashaei

    Full Text Available Story is one of the important and influential literary genres that deserves to research on its structure and content .By study and analysis of a story, the reader could comprehend the textual messages and change his attitude toward life and different issues .After defining of the social novel, the author tries to analyze plot and personification in novel of “Tehran-e- Makhuf” and respond to the questions on the method employed for plot and personification and analyze it from plot and its components such as conflict, suspension and resolution and compare the differences and similarities between old tales and modern novels.The plot of “Tehran-e- Makhuf” is not so complex due to its subject and content and natural order of events dominates on artificial discipline and it lacks open plot. Of main elements of plot, conflict is more outstanding here. This novel is full of emotional and moral conflicts and there is no similarity with historical novels that describe good and bad conflicts. Cause and effect relationship is main element of plot that shadows on the story events .In “Tehrna-e- Makhuf”, the author tries to violate the principles and cause to imbalance in natural events sequences with discomposing rational and experiential relationship and take action toward artificiality and unnatural suspension. In creating suspension by emphasis on incidences in some extremist cases, Kazemi tries to found the story based on the considerable sequence of events and this conduct reduces quality of the story significantly and leads to imbalance in rational and acceptable discipline.Kazemi employs direct or reporting personification mostly. This novel lacks diversity in personage considerably .All characters speak in similar style and there is no particular speech style. The personification of Kazemi in “Tehran-e-Makhuf” is continuous and interdependent in style of old tales and novel in European account. In some cases, he approaches to story

  20. A narratological analysis of Mark 12:1-12: The plot of the Gospel of ...

    African Journals Online (AJOL)

    The purpose of this article is an attempt to read Mark 12: 1-12 in terms of the plot of the Gospel. Firstly a brief survey is given of the development of the term plot from Aristotle to the present, thereafter an own methodological point of departure concerning plot is formulated in order to study the plot of Mark. The conclusions ...

  1. Fuel flow distribution in SOFC stacks revealed by impedance spectroscopy

    DEFF Research Database (Denmark)

    Mosbæk, Rasmus Rode; Hjelm, Johan; Barfod, Rasmus

    2014-01-01

    . An operating stack is subject to compositional gradients in the gaseous reactant streams, and temperature gradients across each cell and across the stack, which complicates detailed analysis. An experimental stack with low ohmic resistance from Topsoe Fuel Cell A/S was characterized using Electrochemical...... Impedance Spectroscopy (EIS). The stack measurement geometry was optimized for EIS by careful selection of the placement of current feeds and voltage probes in order to minimize measurement errors. It was demonstrated that with the improved placement of current feeds and voltage probes it is possible...... to separate the loss contributions in an ohmic and a polarization part and that the low frequency response is useful in detecting mass transfer limitations. This methodology can be used to detect possible minor changes in the supply of gas to the individual cells, which is important when going to high fuel...

  2. Simulation of magnetization and levitation characteristics of HTS tape stacks

    Science.gov (United States)

    Anischenko, I. V.; Pokrovskii, S. V.; Mineev, N. A.

    2017-12-01

    In this work it is presented a computational model of a magnetic levitation system based on stacks of high-temperature second generation superconducting tapes (HTS) GdBa2Cu3O7-x. Calculated magnetic field and the current distributions in the system for different stacks geometries in the zero-field cooling mode are also presented. The magnetization curves of the stacks in the external field of a permanent NdFeB magnet and the levitation force dependence on the gap between the magnet and the HTS tapes stack were obtained. A model of the magnetic system, oriented to levitation application, is given. Results of modeling were compared with the experimental data.

  3. Fast principal component analysis for stacking seismic data

    Science.gov (United States)

    Wu, Juan; Bai, Min

    2018-04-01

    Stacking seismic data plays an indispensable role in many steps of the seismic data processing and imaging workflow. Optimal stacking of seismic data can help mitigate seismic noise and enhance the principal components to a great extent. Traditional average-based seismic stacking methods cannot obtain optimal performance when the ambient noise is extremely strong. We propose a principal component analysis (PCA) algorithm for stacking seismic data without being sensitive to noise level. Considering the computational bottleneck of the classic PCA algorithm in processing massive seismic data, we propose an efficient PCA algorithm to make the proposed method readily applicable for industrial applications. Two numerically designed examples and one real seismic data are used to demonstrate the performance of the presented method.

  4. Static analysis of worst-case stack cache behavior

    DEFF Research Database (Denmark)

    Jordan, Alexander; Brandner, Florian; Schoeberl, Martin

    2013-01-01

    Utilizing a stack cache in a real-time system can aid predictability by avoiding interference that heap memory traffic causes on the data cache. While loads and stores are guaranteed cache hits, explicit operations are responsible for managing the stack cache. The behavior of these operations can......-graph, the worst-case bounds can be efficiently yet precisely determined. Our evaluation using the MiBench benchmark suite shows that only 37% and 21% of potential stack cache operations actually store to and load from memory, respectively. Analysis times are modest, on average running between 0.46s and 1.30s per...... be analyzed statically. We present algorithms that derive worst-case bounds on the latency-inducing operations of the stack cache. Their results can be used by a static WCET tool. By breaking the analysis down into subproblems that solve intra-procedural data-flow analysis and path searches on the call...

  5. A Stack Cache for Real-Time Systems

    DEFF Research Database (Denmark)

    Schoeberl, Martin; Nielsen, Carsten

    2016-01-01

    Real-time systems need time-predictable computing platforms to allowfor static analysis of the worst-case execution time. Caches are important for good performance, but data caches arehard to analyze for the worst-case execution time. Stack allocated data has different properties related to local......Real-time systems need time-predictable computing platforms to allowfor static analysis of the worst-case execution time. Caches are important for good performance, but data caches arehard to analyze for the worst-case execution time. Stack allocated data has different properties related...... to locality, lifetime, and static analyzability of access addresses comparedto static or heap allocated data. Therefore, caching of stack allocateddata benefits from having its own cache. In this paper we present a cache architecture optimized for stack allocateddata. This cache is additional to the normal...

  6. DBaaS with OpenStack Trove

    CERN Document Server

    Giardini, Andrea

    2013-01-01

    The purpose of the project was to evaluate the Trove component for OpenStack, understand if it can be used with the CERN infrastructure and report the benefits and disadvantages of this software. Currently, databases for CERN projects are provided by a DbaaS software developed inside the IT-DB group. This solution works well with the actual infrastructure but it is not easy to maintain. With the migration of the CERN infrastructure to OpenStack the Database group started to evaluate the Trove component. Instead of mantaining an own DbaaS service it can be interesting to migrate everything to OpenStack and replace the actual DbaaS software with Trove. This way both virtual machines and databases will be managed by OpenStack itself.

  7. Stacking dependence of carrier transport properties in multilayered black phosphorous.

    Science.gov (United States)

    Sengupta, A; Audiffred, M; Heine, T; Niehaus, T A

    2016-02-24

    We present the effect of different stacking orders on carrier transport properties of multi-layer black phosphorous. We consider three different stacking orders AAA, ABA and ACA, with increasing number of layers (from 2 to 6 layers). We employ a hierarchical approach in density functional theory (DFT), with structural simulations performed with generalized gradient approximation (GGA) and the bandstructure, carrier effective masses and optical properties evaluated with the meta-generalized gradient approximation (MGGA). The carrier transmission in the various black phosphorous sheets was carried out with the non-equilibrium green's function (NEGF) approach. The results show that ACA stacking has the highest electron and hole transmission probabilities. The results show tunability for a wide range of band-gaps, carrier effective masses and transmission with a great promise for lattice engineering (stacking order and layers) in black phosphorous.

  8. Modeling of a Stacked Power Module for Parasitic Inductance Extraction

    Science.gov (United States)

    2017-09-15

    ARL-TR-8138 ● SEP 2017 US Army Research Laboratory Modeling of a Stacked Power Module for Parasitic Inductance Extraction by...not return it to the originator. ARL-TR-8138 ● SEP 2017 US Army Research Laboratory Modeling of a Stacked Power Module for...aware that notwithstanding any other provision of law , no person shall be subject to any penalty for failing to comply with a collection of information if

  9. National Spherical Torus Experiment (NSTX) Center Stack Upgrade

    International Nuclear Information System (INIS)

    Neumeyer, C.; Avasarala, S.; Chrzanowski, J.; Dudek, L.; Fan, H.; Hatcher, H.; Heitzenroeder, P.; Menard, J.; Ono, M.; Ramakrishnan, S.; Titus, P.; Woolley, R.; Zhan, H.

    2009-01-01

    The purpose of the NSTX Center Stack Upgrade project is to expand the NSTX operational space and thereby the physics basis for next-step ST facilities. The plasma aspect ratio (ratio of plasma major to minor radius) of the upgrade is increased to 1.5 from the original value of 1.26, which increases the cross sectional area of the center stack by a factor of ∼ 3 and makes possible higher levels of performance and pulse duration.

  10. A new method for beam stacking in storage rings

    Energy Technology Data Exchange (ETDEWEB)

    Bhat, C.M.; /Fermilab

    2008-06-01

    Recently, I developed a new beam stacking scheme for synchrotron storage rings called 'longitudinal phase-space coating' (LPSC). This scheme has been convincingly validated by multi-particle beam dynamics simulations and has been demonstrated with beam experiments at the Fermilab Recycler. Here, I present the results from both simulations and experiments. The beam stacking scheme presented here is the first of its kind.

  11. Stacking faults and phase transformations in silicon nitride

    Science.gov (United States)

    Milhet, X.; Demenet, J.-L.; Rabier, J.

    1998-11-01

    From observations of extended dislocation nodes in β silicon nitride, possible stacking fault structures in the basal plane of this compound have been investigated. It has been found that stacking fault structure is locally analogous to α silicon nitride. A phase transformation α to β or β to α can also be achieved by cooperative shear of partial dislocations with 1/3<~ngle1bar{1}00rangle Burgers vectors.

  12. LOFT diesel generator ''A'' exhaust stack seismic analysis

    International Nuclear Information System (INIS)

    Blandford, R.K.

    1978-01-01

    A stress analysis of the LOFT Diesel Generator ''A'' Exhaust Stack was performed to determine its reaction to Safe-Shutdown Earthquake loads. The exhaust stack silencer and supporting foundation was found to be inadequate for the postulated seismic accelerations. Lateral support is required to prevent overturning of the silencer pedestal and reinforcement of the 4'' x 0.5'' silencer base straps is necessary. Basic requirements for this additional support are discussed

  13. Field-induced stacking transition of biofunctionalized trilayer graphene

    Energy Technology Data Exchange (ETDEWEB)

    Masato Nakano, C. [Flintridge Preparatory School, La Canada, California 91011 (United States); Sajib, Md Symon Jahan; Samieegohar, Mohammadreza; Wei, Tao [Dan F. Smith Department of Chemical Engineering, Lamar University, Beaumont, Texas 77710 (United States)

    2016-02-01

    Trilayer graphene (TLG) is attracting a lot of attention as their stacking structures (i.e., rhombohedral vs. Bernal) drastically affect electronic and optical properties. Based on full-atom molecular dynamics simulations, we here predict electric field-induced rhombohedral-to-Bernal transition of TLG tethered with proteins. Furthermore, our simulations show that protein's electrophoretic mobility and diffusivity are enhanced on TLG surface. This phenomenon of controllable TLG stacking transition will contribute to various applications including biosensing.

  14. Aerosol sampling from stacks and ducts at the Rocky Flats Plant

    International Nuclear Information System (INIS)

    McFarlane, A.R.; Anand, N.K.; Ortiz, C.A.

    1995-01-01

    While the Rocky Flats Plant (RFP) in Golden, CO is being decommissioned; there is air flow through the ventilation systems in the buildings. Although the air is HEPA filtered, under the requirements of both the U.S. EPA and the U.S. DOE, several of the stacks and ducts must be continuously monitored for radionuclide aerosol particles, where plutonium is the principal radionuclide of concern. The air sampling effort for compliance with EPA requirements is focussed on the acquisition of representative aerosol samples, which are collected on filters and subsequently analyzed in a laboratory. The goal of the DOE sampling is to acquire representative samples that can be analyzed with near-real-time monitors for alarming purposes, where the alarms are used to warn workers that may be affected by elevated concentrations of radionuclides. The air sampling at RFP is based on single point representative sampling with a shrouded probe. For stacks and ducts that are under the cognizance of EPA, the approach is embodied in a set of Alternate Reference Methodologies that EPA has approved for use at DOE facilities. Shrouded probes were designed based on numerical predictions of performance and the efficacy of the probes was verified by wind tunnel tests. Aerosol transport lines were designed using a code, DEPOSITION that provides optimization of aerosol penetration. Adequacy of a location for single point sampling was based on numerical criteria for mixing of both contaminant mass and fluid momentum as manifested by the uniformity of the velocity profile and the profiles of tracer gas and aerosol particles. Scale models were constructed of key ducts and these were tested in the laboratory to determine the proper locations. For ducts and stacks that fall under DOE, but not EPA requirements, similar methodology was used; however, the single point sampling location is based on alarming considerations

  15. Correlation analysis of respiratory signals by using parallel coordinate plots.

    Science.gov (United States)

    Saatci, Esra

    2018-01-01

    The understanding of the bonds and the relationships between the respiratory signals, i.e. the airflow, the mouth pressure, the relative temperature and the relative humidity during breathing may provide the improvement on the measurement methods of respiratory mechanics and sensor designs or the exploration of the several possible applications in the analysis of respiratory disorders. Therefore, the main objective of this study was to propose a new combination of methods in order to determine the relationship between respiratory signals as a multidimensional data. In order to reveal the coupling between the processes two very different methods were used: the well-known statistical correlation analysis (i.e. Pearson's correlation and cross-correlation coefficient) and parallel coordinate plots (PCPs). Curve bundling with the number intersections for the correlation analysis, Least Mean Square Time Delay Estimator (LMS-TDE) for the point delay detection and visual metrics for the recognition of the visual structures were proposed and utilized in PCP. The number of intersections was increased when the correlation coefficient changed from high positive to high negative correlation between the respiratory signals, especially if whole breath was processed. LMS-TDE coefficients plotted in PCP indicated well-matched point delay results to the findings in the correlation analysis. Visual inspection of PCB by visual metrics showed range, dispersions, entropy comparisons and linear and sinusoidal-like relationships between the respiratory signals. It is demonstrated that the basic correlation analysis together with the parallel coordinate plots perceptually motivates the visual metrics in the display and thus can be considered as an aid to the user analysis by providing meaningful views of the data. Copyright © 2017 Elsevier B.V. All rights reserved.

  16. Plant species richness enhances nitrogen retention in green roof plots.

    Science.gov (United States)

    Johnson, Catherine; Schweinhart, Shelbye; Buffam, Ishi

    2016-10-01

    Vegetated (green) roofs have become common in many cities and are projected to continue to increase in coverage, but little is known about the ecological properties of these engineered ecosystems. In this study, we tested the biodiversity-ecosystem function hypothesis using commercially available green roof trays as replicated plots with varying levels of plant species richness (0, 1, 3, or 6 common green roof species per plot, using plants with different functional characteristics). We estimated accumulated plant biomass near the peak of the first full growing season (July 2013) and measured runoff volume after nearly every rain event from September 2012 to September 2013 (33 events) and runoff fluxes of inorganic nutrients ammonium, nitrate, and phosphate from a subset of 10 events. We found that (1) total plant biomass increased with increasing species richness, (2) green roof plots were effective at reducing storm runoff, with vegetation increasing water retention more than soil-like substrate alone, but there was no significant effect of plant species identity or richness on runoff volume, (3) green roof substrate was a significant source of phosphate, regardless of presence/absence of plants, and (4) dissolved inorganic nitrogen (DIN = nitrate + ammonium) runoff fluxes were different among plant species and decreased significantly with increasing plant species richness. The variation in N retention was positively related to variation in plant biomass. Notably, the increased biomass and N retention with species richness in this engineered ecosystem are similar to patterns observed in published studies from grasslands and other well-studied ecosystems. We suggest that more diverse plantings on vegetated roofs may enhance the retention capacity for reactive nitrogen. This is of importance for the sustained health of vegetated roof ecosystems, which over time often experience nitrogen limitation, and is also relevant for water quality in receiving waters

  17. Measurements of proton energy spectra using a radiochromic film stack

    Science.gov (United States)

    Filkins, T. M.; Steidle, Jessica; Ellison, D. M.; Steidle, Jeffrey; Freeman, C. G.; Padalino, S. J.; Fiksel, G.; Regan, S. P.; Sangster, T. C.

    2014-10-01

    The energy spectrum of protons accelerated from the rear-side of a thin foil illuminated with ultra-intense laser light from the OMEGA EP laser system at the University of Rochester's Laboratory for Laser Energetics (LLE) was measured using a stack of radiochromic film (RCF). The film stack consisted of four layers of Gafchromic HD-V2 film and four layers of Gafchromic MD-V2-55 film. Aluminum foils of various thicknesses were placed between each piece of RCF in the stack. This arrangement allowed protons with energies of 30 MeV to reach the back layer of RCF in the stack. The stack was placed in the detector plane of a Thomson parabola ion energy (TPIE) spectrometer. Each piece of film in the stack was scanned using a commercially available flat-bed scanner (Epson 10000XL). The resulting optical density was converted into proton fluence using an absolute calibration of the RCF obtained at the SUNY Geneseo 1.7 MV Pelletron accelerator laboratory. In these calibration measurements, the sensitivity of the radiochromic film was measured using monoenergetic protons produced by the accelerator. Details of the analysis procedure and the resulting proton energy spectra will be presented. Funded in part by a grant from the DOE through the Laboratory for Laser Energetics.

  18. Standoff Stack Emissions Monitoring Using Short Range Lidar

    Science.gov (United States)

    Gravel, Jean-Francois Y.; Babin, Francois; Allard, Martin

    2016-06-01

    There are well documented methods for stack emissions monitoring. These are all based on stack sampling through sampling ports in well defined conditions. Once sampled, the molecules are quantified in instruments that often use optical techniques. Unfortunately sampling ports are not found on all stacks/ducts or the use of the sampling ports cannot be planned efficiently because of operational constraints or the emissions monitoring equipment cannot be driven to a remote stack/duct. Emissions monitoring using many of the same optical techniques, but at a standoff distance, through the atmosphere, using short range high spatial resolution lidar techniques was thus attempted. Standoff absorption and Raman will be discussed and results from a field campaign will be presented along with short descriptions of the apparatus. In the first phase of these tests, the molecules that were targeted were NO and O2. Spatially resolved optical measurements allow for standoff identification and quantification of molecules, much like the standardized methods, except for the fact that it is not done in the stack, but in the plume formed by the emissions from the stack. The pros and cons will also be discussed, and in particular the problem of mass emission estimates that require the knowledge of the flow rate and the distribution of molecular concentration in the plane of measurement.

  19. Standoff Stack Emissions Monitoring Using Short Range Lidar

    Directory of Open Access Journals (Sweden)

    Gravel Jean-Francois Y.

    2016-01-01

    Full Text Available There are well documented methods for stack emissions monitoring. These are all based on stack sampling through sampling ports in well defined conditions. Once sampled, the molecules are quantified in instruments that often use optical techniques. Unfortunately sampling ports are not found on all stacks/ducts or the use of the sampling ports cannot be planned efficiently because of operational constraints or the emissions monitoring equipment cannot be driven to a remote stack/duct. Emissions monitoring using many of the same optical techniques, but at a standoff distance, through the atmosphere, using short range high spatial resolution lidar techniques was thus attempted. Standoff absorption and Raman will be discussed and results from a field campaign will be presented along with short descriptions of the apparatus. In the first phase of these tests, the molecules that were targeted were NO and O2. Spatially resolved optical measurements allow for standoff identification and quantification of molecules, much like the standardized methods, except for the fact that it is not done in the stack, but in the plume formed by the emissions from the stack. The pros and cons will also be discussed, and in particular the problem of mass emission estimates that require the knowledge of the flow rate and the distribution of molecular concentration in the plane of measurement.

  20. WASP (Write a Scientific Paper) using Excel - 3: Plotting data.

    Science.gov (United States)

    Grech, Victor

    2018-02-13

    The plotting of data into graphs should be a mandatory step in all data analysis as part of a descriptive statistics exercise, since it gives the researcher an overview of the shape and nature of the data. Moreover, outlier values may be identified, which may be incorrect data, or true outliers, from which important findings (and publications) may arise. This exercise should always precede inferential statistics, when possible, and this paper in the Early Human Development WASP series provides some pointers for doing so in Microsoft Excel™. Copyright © 2018 Elsevier B.V. All rights reserved.

  1. Graphical interpretation of confidence curves in rankit plots

    DEFF Research Database (Denmark)

    Hyltoft Petersen, Per; Blaabjerg, Ole; Andersen, Marianne

    2004-01-01

    A well-known transformation from the bell-shaped Gaussian (normal) curve to a straight line in the rankit plot is investigated, and a tool for evaluation of the distribution of reference groups is presented. It is based on the confidence intervals for percentiles of the calculated Gaussian...... will fit to the straight line describing the calculated In-Gaussian distribution. The quality of the fit is evaluated by adding confidence intervals (CI) to each point on the line and calculating the percentage of points outside the hyperbola-like CI-curves. The assumption was that the 95% confidence...

  2. TORCAPP: time-dependent cyclotron orbit calculation and plotting package

    International Nuclear Information System (INIS)

    Maddox, L.B.; McNeilly, G.S.

    1979-11-01

    TORCAPP calculates the motion of charged particles in electromagnetic fields with time as the independent variable, and produces a variety of printed and plotted output of results. Finite-size beam behavior is studied conveniently by following groups of particles which define an appropriate phase space area. Since time is the independent variable, general motion in the near-median-plane region may be followed. This includes, for example, loops not enclosing the origin and strongly radial motions. Thus, TORCAPP is particularly useful for injection studies for isochronous cyclotrons, or other devices with near-median-plane charged particle motion

  3. Effect of Carbon Fraction on Stacking Fault Energy of Austenitic Stainless Steels

    Science.gov (United States)

    Lee, Tae-Ho; Ha, Heon-Young; Hwang, Byoungchul; Kim, Sung-Joon; Shin, Eunjoo

    2012-12-01

    The effect of C fraction (C/N) on stacking fault energy (SFE) of austenitic Fe-18Cr-10Mn steels with a fixed amount of C + N (0.6 wt pct) was investigated by means of neutron diffraction and transmission electron microscopy (TEM). The SFE were evaluated by the Rietveld whole-profile fitting combined with the double-Voigt size-strain analysis for neutron diffraction profiles using neutron diffraction. The measured SFE showed distinguishable difference and were well correlated with the change in deformation microstructure. Three-dimensional linear regression analyses yielded the relation reflecting the contribution of both C + N and C/N: SFE (mJ/m2) = -5.97 + 39.94(wt pct C + N) + 3.81(C/N). As C fraction increased, the strain-induced γ→ ɛ martensitic transformation was suppressed, and deformation twinning became the primary mode of plastic deformation.

  4. PLOTNFIT.4TH, Data Plotting and Curve Fitting by Polynomials

    International Nuclear Information System (INIS)

    Schiffgens, J.O.

    1990-01-01

    1 - Description of program or function: PLOTnFIT is used for plotting and analyzing data by fitting nth degree polynomials of basis functions to the data interactively and printing graphs of the data and the polynomial functions. It can be used to generate linear, semi-log, and log-log graphs and can automatically scale the coordinate axes to suit the data. Multiple data sets may be plotted on a single graph. An auxiliary program, READ1ST, is included which produces an on-line summary of the information contained in the PLOTnFIT reference report. 2 - Method of solution: PLOTnFIT uses the least squares method to calculate the coefficients of nth-degree (up to 10. degree) polynomials of 11 selected basis functions such that each polynomial fits the data in a least squares sense. The procedure incorporated in the code uses a linear combination of orthogonal polynomials to avoid 'i11-conditioning' and to perform the curve fitting task with single-precision arithmetic. 3 - Restrictions on the complexity of the problem - Maxima of: 225 data points per job (or graph) including all data sets 8 data sets (or tasks) per job (or graph)

  5. TREDRA, Minimal Cut Sets Fault Tree Plot Program

    International Nuclear Information System (INIS)

    Fussell, J.B.

    1983-01-01

    1 - Description of problem or function: TREDRA is a computer program for drafting report-quality fault trees. The input to TREDRA is similar to input for standard computer programs that find minimal cut sets from fault trees. Output includes fault tree plots containing all standard fault tree logic and event symbols, gate and event labels, and an output description for each event in the fault tree. TREDRA contains the following features: a variety of program options that allow flexibility in the program output; capability for automatic pagination of the output fault tree, when necessary; input groups which allow labeling of gates, events, and their output descriptions; a symbol library which includes standard fault tree symbols plus several less frequently used symbols; user control of character size and overall plot size; and extensive input error checking and diagnostic oriented output. 2 - Method of solution: Fault trees are generated by user-supplied control parameters and a coded description of the fault tree structure consisting of the name of each gate, the gate type, the number of inputs to the gate, and the names of these inputs. 3 - Restrictions on the complexity of the problem: TREDRA can produce fault trees with a minimum of 3 and a maximum of 56 levels. The width of each level may range from 3 to 37. A total of 50 transfers is allowed during pagination

  6. Potato production on private plots contaminated by radionuclides

    International Nuclear Information System (INIS)

    Bogdevitch, I.; Tarasiuk, S.

    2004-01-01

    Potatoes is one of the basis food products of man diet, especially in country area. Recent research has shown that 137 Cs content in potato tubers does not exceed the permissible level at the potato growing on radioactive contaminated land in Belarus. However up to 240-300 kg of potatoes is consumed per man during year and potato yield determines significant share of the internal dose of radiation. Moreover, extra potato yield sold on market is forming the essential part of the rural family budget. Therefore the reducing of 137 Cs content in potatoes and increasing of potato yield could be allowed to improve of quality life of rural inhabitants on contaminated areas. The application of protection measures on private plots are restricted by lack of the knowledge and financial deficit. The involvement of rural inhabitants in processes of self-rehabilitation and self-development could be a way to improve the quality life on radioactive contaminated territory There is strong motivation for inhabitants to increase the yield and to reduce the radionuclide concentration in potatoes. How to develop the conditions for the sustainable potato production by private producers on affected land? There are several factors to consider. Firstly, the rural inhabitants should be actively involved as initiators to improve their quality life. Secondly, the potato technology should be adopted to the local territory and tested by producers on radiological and economic efficiency. Thirdly, the common village initiatives should be developed for supplying by new varieties of seeds and fertilizers, selling of yield, consulting, crediting etc. The step-by-step solution of described strategy could allow improving and stabilizing the potato production by rural community. The training of rural people as an initial step was realized to transfer to the inhabitants the practical skills that can be used in their day-to-day life within framework of 'ETHOS-II' project. The experimental potato

  7. Three-Dimensional Modeling of the Detonation of a Munitions Stack and the Loading on an Adjacent Stack Protected by a Water Barricade

    National Research Council Canada - National Science Library

    Lottero, Richard

    2001-01-01

    This report describes the results of three-dimensional (3-D) hydrocode computations modeling the detonation of a donor munitions stack and the loading on and response of a protective water barricade and a nearby acceptor munitions stack...

  8. Correlation plot facility in the SLC control system

    International Nuclear Information System (INIS)

    Hendrickson, L.; Phinney, N.; Sanchez-Chopitea, L.

    1991-05-01

    The Correlation Plot facility is a powerful interactive tool for data acquisition and analysis throughout the SLC. A generalized interface allows the user to perform a wide variety of machine physics experiments without the need for specialized software. It has been used extensively during SLC commissioning and operation. The user may step one or two independent parameters such as magnet or feedback setpoints while measuring or calculating up to 160 others. Measured variables include all analog signals available to the control system as well as a variety of derived parameters such as beam size or emittance. Various fitting algorithms and display options are provided for data analysis. A software-callable interface is also provided. Applications based on this facility are used to phase klystrons, measure emittance and dispersion, minimize beam size at the interaction point and maintain beam collisions. 4 refs., 3 figs

  9. Finding the plot in South African reading education

    Directory of Open Access Journals (Sweden)

    Peter Rule

    2017-09-01

    Full Text Available This article argues that we have lost the plot in South African reading education. To find it, we need to move beyond the predominant mode of reading as oral performance, where the emphasis is on accuracy and pronunciation, to reading as comprehension of meaning in text. While reading research in South Africa has been conducted mainly in school contexts, this case study is of a school and Adult Basic Education and Training Centre in a rural KwaZulu-Natal community near Pietermaritzburg. It found that an oratorical approach to reading dominated in both settings. It suggests that developing the way in which teachers understand the teaching of reading and transforming the teaching practices of those who teach as they were taught in the education system of the apartheid era are key to improving the teaching of reading.

  10. D.3.2 PLOT Persuasive Learning Design Framework

    DEFF Research Database (Denmark)

    Gram-Hansen, Sandra Burri; Schärfe, Henrik; Winther-Nielsen, Nicolai

    2011-01-01

    This deliverable is the second of three deliverables in WP3: Persuasive Learning Design Framework, and draws upon the theoretical foundation presented in the first deliverable D.3.1, as the persuasive potential of existing systems are explored, analysed and discussed. D.3.2. is formally described...... as an: ‚Internal report for project use containing an empirically-based assessment of existing systems and their potential in terms of learning and persuasion. This will be used as a discussion document by the consortium.‛ To meet the requirements of this deliverable, this documents presents analysis...... of the technological learning tools and products which are currently related to the PLOT project, namely the GLOMaker and the 3ET tool, and a selection of GLOs and learning exercises. The primary focus of the analysis is to explore how the theoretical perspectives presented in D.3.1 are represented in these tools...

  11. Histogram plots and cutoff energies for nuclear discrete levels

    International Nuclear Information System (INIS)

    Belgya, T.; Molnar, G.; Fazekas, B.; Oestoer, J.

    1997-05-01

    Discrete level schemes for 1277 nuclei, from 6 Li through 251 Es, extracted from the Evaluated Nuclear Structure Data File were analyzed. Cutoff energies (U max ), indicating the upper limit of level scheme completeness, were deduced from the inspection of histograms of the cumulative number of levels. Parameters of the constant-temperature level density formula (nuclear temperature T and energy shift U 0 ) were obtained by means of the least square fit of the formula to the known levels below cutoff energy. The results are tabulated for all 1277 nuclei allowing for an easy and reliable application of the constant-temperature level density approach. A complete set of cumulative plots of discrete levels is also provided. (author). 5 figs, 2 tabs

  12. Generalized diffraction-stack migration and filtering of coherent noise

    KAUST Repository

    Zhan, Ge

    2014-01-27

    We reformulate the equation of reverse-time migration so that it can be interpreted as summing data along a series of hyperbola-like curves, each one representing a different type of event such as a reflection or multiple. This is a generalization of the familiar diffraction-stack migration algorithm where the migration image at a point is computed by the sum of trace amplitudes along an appropriate hyperbola-like curve. Instead of summing along the curve associated with the primary reflection, the sum is over all scattering events and so this method is named generalized diffraction-stack migration. This formulation leads to filters that can be applied to the generalized diffraction-stack migration operator to mitigate coherent migration artefacts due to, e.g., crosstalk and aliasing. Results with both synthetic and field data show that generalized diffraction-stack migration images have fewer artefacts than those computed by the standard reverse-time migration algorithm. The main drawback is that generalized diffraction-stack migration is much more memory intensive and I/O limited than the standard reverse-time migration method. © 2014 European Association of Geoscientists & Engineers.

  13. Effect of flow parameters on flare stack generator noise

    International Nuclear Information System (INIS)

    Dinn, T.S.

    1998-01-01

    The SoundPLAN Computer Noise Model was used to determine the general effect of flare noise in a community adjacent to a petrochemical plant. Tests were conducted to determine the effect of process flow conditions and the pulsating flame on the flare stack generator noise from both a refinery flare and process flare. Flaring under normal plant operations, the flaring of fuel gas and the flaring of hydrogen were the three conditions that were tested. It was shown that the steam flow rate was the determining factor in the flare stack generated noise. Variations in the water seal level in the flare line surge tank increased or decreased the gas flowrate, which resulted in a pulsating flame. The period and amplitude of the pulsating noise from the flare stacks was determined by measuring several parameters. Flare stack noise oscillations were found to be greater for the process flare than for the refinery flare stack. It was suggested that minimizing the amount of steam fed to the flare and improving the burner design would minimize noise. 2 tabs., 6 figs

  14. Estimation of stacking fault and twin energies in transition metals

    International Nuclear Information System (INIS)

    Papon, Anne-Marie

    1979-01-01

    As twins and stacking faults play an important role in the plastic deformation of metals, the objective of this research thesis is, by using an as correct as possible description of band d state density, to assess the internal energy of twins and stacking faults in metals with a CFC, HC or CC crystal structure. If, in transition metals, cohesion mainly results from d electron attraction, other terms intervening in crystal equilibrium must also be taken into account. Thus, the author proposes a decomposition of cohesion energy. The geometry of twins and stacking faults in compact phases is defined, and energy calculations are presented and discussed. Alloying effects are then addressed, as well as a general comparison with available experimental results. After a geometric description of twins and stacking faults in CC structures, their energies are calculated for a Gaussian distribution of state density. For higher order moments, defect energy due to d orbital anisotropy is assessed, and then applied to energy and stability calculations in twins and stacking faults for various relaxed atomic configurations

  15. Dimensional crossover of electron weak localization in ZnO/TiOx stacked layers grown by atomic layer deposition

    Science.gov (United States)

    Saha, D.; Misra, P.; Bhartiya, S.; Gupta, M.; Joshi, M. P.; Kukreja, L. M.

    2016-01-01

    We report on the dimensional crossover of electron weak localization in ZnO/TiOx stacked layers having well-defined and spatially-localized Ti dopant profiles along film thickness. These films were grown by in situ incorporation of sub-monolayer TiOx on the growing ZnO film surface and subsequent overgrowth of thin conducting ZnO spacer layer using atomic layer deposition. Film thickness was varied in the range of ˜6-65 nm by vertically stacking different numbers (n = 1-7) of ZnO/TiOx layers of nearly identical dopant-profiles. The evolution of zero-field sheet resistance (R⊙) versus temperature with decreasing film thickness showed a metal to insulator transition. On the metallic side of the metal-insulator transition, R⊙(T) and magnetoresistance data were found to be well corroborated with the theoretical framework of electron weak localization in the diffusive transport regime. The temperature dependence of both R⊙ and inelastic scattering length provided strong evidence for a smooth crossover from 2D to 3D weak localization behaviour. Results of this study provide deeper insight into the electron transport in low-dimensional n-type ZnO/TiOx stacked layers which have potential applications in the field of transparent oxide electronics.

  16. Pre-ABoVE: Arctic Vegetation Plots, Unalaska Island, Aleutian Islands, Alaska, 2007

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set provides environmental, soil, and vegetation data collected during August 2007 from 69 study plots at the Unalaska Island research site, and one plot...

  17. Communication: Thermodynamics of stacking disorder in ice nuclei

    Science.gov (United States)

    Quigley, D.

    2014-09-01

    A simple Ising-like model for the stacking thermodynamics of ice 1 is constructed for nuclei in supercooled water, and combined with classical nucleation theory. For relative stabilities of cubic and hexagonal ice I within the range of experimental estimates, this predicts critical nuclei are stacking disordered at strong sub-cooling, consistent with recent experiments. At higher temperatures nucleation of pure hexagonal ice is recovered. Lattice-switching Monte-Carlo is applied to accurately compute the relative stability of cubic and hexagonal ice for the popular mW model of water. Results demonstrate that this model fails to adequately capture the relative energetics of the two polytypes, leading to stacking disorder at all temperatures.

  18. Reliability assessment of germanium gate stacks with promising initial characteristics

    Science.gov (United States)

    Lu, Cimang; Lee, Choong Hyun; Nishimura, Tomonori; Nagashio, Kosuke; Toriumi, Akira

    2015-02-01

    This work reports on the reliability assessment of germanium (Ge) gate stacks with promising initial electrical properties, with focus on trap generation under a constant electric stress field (Estress). Initial Ge gate stack properties do not necessarily mean highly robust reliability when it is considered that traps are newly generated under high Estress. A small amount of yttrium- or scandium oxide-doped GeO2 (Y-GeO2 or Sc-GeO2, respectively) significantly reduces trap generation in Ge gate stacks without deterioration of the interface. This is explained by the increase in the average coordination number (Nav) of the modified GeO2 network that results from the doping.

  19. Edge-edge interactions in stacked graphene nanoplatelets

    Energy Technology Data Exchange (ETDEWEB)

    Cruz Silva, Eduardo [ORNL; Terrones Maldonado, Humberto [ORNL; Terrones Maldonado, Mauricio [ORNL; Jia, Xiaoting [Massachusetts Institute of Technology (MIT); Sumpter, Bobby G [ORNL; Dresselhaus, M [Massachusetts Institute of Technology (MIT); Meunier, V. [Rensselaer Polytechnic Institute (RPI)

    2013-01-01

    High-resolution transmission electron microscopy (HRTEM) studies show the dynamics of small graphene platelets on larger graphene layers. The platelets move nearly freely to eventually lock in at well-defined positions close to the edges of the larger underlying graphene sheet. While such movement is driven by a shallow potential energy surface described by an interplane interaction, the lock-in position occurs by via edge-edge interactions of the platelet and the graphene surface located underneath. Here we quantitatively study this behavior using van der Waals density functional calculations. Local interactions at the open edges are found to dictate stacking configurations that are different from Bernal (AB) stacking. These stacking configurations are known to be otherwise absent in edge-free two-dimensional (2D) graphene. The results explain the experimentally observed platelet dynamics and provide a detailed account of the new electronic properties of these combined systems.

  20. Magneto-optical properties of ABC-stacked trilayer graphene.

    Science.gov (United States)

    Lin, Yi-Ping; Lin, Chiun-Yan; Ho, Yen-Hung; Do, Thi-Nga; Lin, Ming-Fa

    2015-06-28

    The generalized tight-binding model is developed to investigate the magneto-optical absorption spectra of ABC-stacked trilayer graphene. The absorption peaks can be classified into nine categories of inter-Landau-level optical excitations, including three intra-group and six inter-group ones. Most of them belong to the twin-peak structures because of the asymmetric Landau level spectrum. The threshold absorption peak alone comes from a certain excitation channel, and its frequency is associated with a specific interlayer atomic interaction. The Landau-level anticrossings cause extra absorption peaks. Moreover, a simple relationship between the absorption frequency and the field strength is absent. The magneto-optical properties of ABC-stacked trilayer graphene are totally different from those of AAA- and ABA-stacked ones, such as the number, intensity and frequency of absorption peaks.

  1. Thermoacoustic design using stem of goose down stack

    Science.gov (United States)

    Farikhah, Irna; Ristanto, Sigit; Idrus, Hadiyati; Kaltsum, Ummi; Faisal, Affandi; Setiawan, Ihsan; Setio Utomo, Agung Bambang

    2012-09-01

    Many refrigerators using CFC as a refrigerant are seen as the cause of the depletion of ozone. Hence, thermoacoustic was chosen as an alternative refrigerator that safe for environment. There are many variable that influenced the optimization of thermoacoustic design. One of them is thermal conductivity of material of stack. The Stack material must have a low thermal conductivity. In this research we used organic stack made of stem of goose down. It has superior thermal insulating. It means that they have the lowest thermal conductivity. The system uses no refrigerant or compressor, and the only mechanical moving part is the loudspeaker connected to a signal generator that produces the acoustic. The working fluid is air and the material of resonator is stainless steel. A series test on the laboratory found that there is a decrease of 5°C in temperature for about 2 minutes.

  2. The measurement of power reactor stack releases under accident conditions

    International Nuclear Information System (INIS)

    Stroem, L.

    1989-01-01

    The performance of a typical Swedish monitor for ventilation stack radioactivity releases is examined critically with respect to accident generated radioactive particles. The conditions in the stack, particle character, and the monitor design are considered. A large LOCA outside the containment leads to high relative humidity, and high temperature, or mist in the stack. A small external LOCA results in a moderate increase in temperature and humidity, and condensing conditions only with reduced ventilation. Particle size and stickiness are estimated for different types of accident. A particle is sticky if it adheres after contact with a solid, smooth, dry, and clean surface. The monitor performance is concluded to be poor for large, sticky particles, like mist droplets. Dense aerosols, like fire smoke, will plug the sampling filter. Non-sticky particles are generally sampled with acceptable accuracy. (au)

  3. Electric toy vehicle powered by a PEMFC stack

    Energy Technology Data Exchange (ETDEWEB)

    Beneito, Ruben; Vilaplana, Joaquin; Gisbert, Santiago [Technological Institute for Toy (AIJU), 03440 Ibi (Spain)

    2007-07-15

    The article describes the design and development of an electric toy vehicle powered by a fuel cell stack. The system consisted of a 150 W PEMFC stack powered by hydrogen/air, a tank of metal hydrides of AB (TiFe) alloy type with a capacity of 300 standard litres, for storing hydrogen, and an electronic power device based on electrolytic capacitors, to supply peak power demands during acceleration and start up of the vehicle. The air supply was provided by a fan preceded by a filter, and in a similar manner the stack was cooled by an air ventilation system. An electrovalve was used to supply H{sub 2} in dead-ended mode. All the components were integrated in the vehicle, and the prototype was tested in real working conditions, in a test bench and by children. (author)

  4. Piezoelectric stack actuator parameter extraction with hysteresis compensation

    DEFF Research Database (Denmark)

    Zsurzsan, Tiberiu-Gabriel; Mangeot, Charles; Andersen, Michael A. E.

    2014-01-01

    The Piezoelectric Actuator Drive (PAD) is a type of rotary motor that transforms the linear motion of piezoelectric stack actuators into a precise rotational motion. The very high stiffness of the actuators employed make this type of motor suited for open-loop control, but the inherent hysteresis...... exhibited by piezoelectric ceramics causes losses. Therefore, this paper presents a straightforward method to measure piezoelectric stack actuator equiv- alent parameters that includes nonlinearities. By folding the nonlinearities into a newly-defined cou- pling coefficient, the inherent hysteretic behavior...... of piezoelectric stack actuators can be greatly reduced through precompensation. Experimental results show a fitting accuracy of 98.8 % between the model and measurements and a peak absolute error reduction by a factor of 10 compared to the manufacturer- provided parameter. This method improves both the static...

  5. Stacking and discontinuous buffers in capillary zone electrophoresis.

    Science.gov (United States)

    Shihabi, Z K

    2000-08-01

    Discontinuous buffers for capillary zone electrophoresis (CZE) can be used under less rigid conditions compared to those for isotachophoresis for stacking. They can be prepared simply by modifying the sample itself, either by addition of small inorganic ions, low conductivity diluents, or both, and also by adjusting its pH, meanwhile injecting a large volume on the capillary. Zwitterionic and organic-based buffers such as triethanolamine and tris(hydroxymethyl)aminomethane (Tris) are well suited for stacking due to their low conductivity, provided the buffer is discontinuous as demonstrated here. A simple mechanism based on discontinuous buffers is described to explain many of the observed stacking types in CZE, pointing out the many similarities to transient isotachophoresis.

  6. Salt Concentration Differences Alter Membrane Resistance in Reverse Electrodialysis Stacks

    KAUST Repository

    Geise, Geoffrey M.

    2014-01-14

    Membrane ionic resistance is usually measured by immersing the membrane in a salt solution at a single, fixed concentration. While salt concentration is known to affect membrane resistance when the same concentration is used on both sides of the membrane, little is known about membrane resistance when the membrane is placed between solutions of different concentrations, such as in a reverse electrodialysis (RED) stack. Ionic resistance measurements obtained using Selemion CMV and AMV that separated sodium chloride and ammonium bicarbonate solutions of different concentrations were greater than those measured using only the high-concentration solution. Measured RED stack resistances showed good agreement with resistances calculated using an equivalent series resistance model, where the membranes accounted for 46% of the total stack resistance. The high area resistance of the membranes separating different salt concentration solutions has implications for modeling and optimizing membranes used in RED systems.

  7. Continued SOFC cell and stack technology and improved production methods

    Energy Technology Data Exchange (ETDEWEB)

    Wandel, M.; Brodersen, K.; Phair, J. (and others)

    2009-05-15

    Within this project significant results are obtained on a number of very diverse areas ranging from development of cell production, metallic creep in interconnect to assembling and test of stacks with foot print larger than 500 cm2. Out of 38 milestones 28 have been fulfilled and 10 have been partly fulfilled. This project has focused on three main areas: 1) The continued cell development and optimization of manufacturing processes aiming at production of large foot-print cells, improving cell performance and development environmentally more benign production methods. 2) Stack technology - especially stacks with large foot print and improving the stack design with respect to flow geometry and gas leakages. 3) Development of stack components with emphasis on sealing (for 2G as well as 3G), interconnect (coat, architecture and creep) and test development. Production of cells with a foot print larger than 500 cm2 is very difficult due to the brittleness of the cells and great effort has been put into this topic. Eight cells were successfully produced making it possible to assemble and test a real stack thereby giving valuable results on the prospects of stacks with large foot print. However, the yield rate is very low and a significant development to increase this yield lies ahead. Several lessons were learned on the stack level regarding 'large foot print' stacks. Modelling studies showed that the width of the cell primarily is limited by production and handling of the cell whereas the length (in the flow direction) is limited by e.g. pressure drop and necessary manifolding. The optimal cell size in the flow direction was calculated to be between approx20 cm and < 30 cm. From an economical point of view the production yield is crucial and stacks with large foot print cell area are only feasible if the cell production yield is significantly enhanced. Co-casting has been pursued as a production technique due to the possibilities in large scale production

  8. Electrically Conductive and Protective Coating for Planar SOFC Stacks

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Jung-Pyung; Stevenson, Jeffry W.

    2017-12-04

    Ferritic stainless steels are preferred interconnect materials for intermediate temperature SOFCs because of their resistance to oxidation, high formability and low cost. However, their protective oxide layer produces Cr-containing volatile species at SOFC operating temperatures and conditions, which can cause cathode poisoning. Electrically conducting spinel coatings have been developed to prevent cathode poisoning and to maintain an electrically conductive pathway through SOFC stacks. However, this coating is not compatible with the formation of stable, hermetic seals between the interconnect frame component and the ceramic cell. Thus, a new aluminizing process has been developed by PNNL to enable durable sealing, prevent Cr evaporation, and maintain electrical insulation between stack repeat units. Hence, two different types of coating need to have stable operation of SOFC stacks. This paper will focus on the electrically conductive coating process. Moreover, an advanced coating process, compatible with a non-electrically conductive coating will be

  9. Multipole Stack for the 800 MeV PS Booster

    CERN Multimedia

    1975-01-01

    The 800 MeV PS Booster had seen first beam in its 4 superposed rings in 1972, routine operation began in 1973. In the strive for ever higher beam intensities, the need for additional multipole lenses became evident. After detailed studies, the manufacture of 8 stacks of multipoles was launched in 1974. Each stack consists of 4 superposed multipoles and each multipole has 4 concentric shells. From the innermost to the outermost shell, Type A contains octupole, skew-octupole, sextupole, skew-sextupole. Type B contains skew-octupole, skew-sextupole, vertical dipole, horizontal dipole. Completion of installation in 1976 opened the way to higher beam intensities. M. Battiaz is seen here with a multipole stack and its many electrical connections.

  10. Improved estimates of per-plot basal area from angle count inventories

    OpenAIRE

    Eastaugh CS; Hasenauer H

    2014-01-01

    Forest inventories were originally designed for the assessment of timber stocks over large areas. The large datasets gathered by these programs are becoming of increasing interest in other applications, particularly in ecosystem modeling. With inventory designs based on sampling proportional to size (angle-count plots) users should be cautious of using data pertaining to individual plots, as the plot-wise data is a statistical estimate rather than a true measurement. Estimates of per-plot bas...

  11. Nuclear fuel rod with retainer for pellet stack

    International Nuclear Information System (INIS)

    Cloue, J.M.

    1986-01-01

    The rod, usable in pressurized water reactors, comprises a stack of fuel pellets and means holding the stack against an end plug of the fuel can during handling operations. These means include a radially expansive element (retainer) of which the shape is so that when it is free at ambient temperature it is gripping the inside of the casing, and a temperature sensitive spacer which contracts the retainer to release it from the casing at a temperature between the ambient and the operating temperature of a reactor [fr

  12. Implementing cloud storage with OpenStack Swift

    CERN Document Server

    Rajana, Kris; Varma, Sreedhar

    2014-01-01

    This tutorial-based book has a step-by-step approach for each topic, ensuring it is thoroughly covered and easy to follow. If you are an IT administrator who wants to enter the world of cloud storage using OpenStack Swift, then this book is ideal for you. Whether your job is to build, manage, or use OpenStack Swift, this book is an ideal way to move your career ahead. Only basic Linux and server technology skills are expected, to take advantage of this book.

  13. Exact Solutions to the Double TSP with Multiple Stacks

    DEFF Research Database (Denmark)

    Petersen, Hanne Løhmann; Archetti, Claudia; Madsen, Oli B.G.

    In the Double Travelling Salesman Problem with Multiple Stacks (DTSPMS) a set of orders is given, each one requiring transportation of one item from a customer in a pickup region to a customer in a delivery region. The vehicle available for the transportation in each region carries a container......, which is organised in rows of given length. Each row is handled independently from the others according to a LIFO stack policy. The DTSPMS consists in determining the pickup tour, the loading plan of the container and the delivery tour in such a way that the total length of the two tours is minimised...

  14. Hardware Evaluation of the Horizontal Exercise Fixture with Weight Stack

    Science.gov (United States)

    Newby, Nate; Leach, Mark; Fincke, Renita; Sharp, Carwyn

    2009-01-01

    HEF with weight stack seems to be a very sturdy and reliable exercise device that should function well in a bed rest training setting. A few improvements should be made to both the hardware and software to improve usage efficiency, but largely, this evaluation has demonstrated HEF's robustness. The hardware offers loading to muscles, bones, and joints, potentially sufficient to mitigate the loss of muscle mass and bone mineral density during long-duration bed rest campaigns. With some minor modifications, the HEF with weight stack equipment provides the best currently available means of performing squat, heel raise, prone row, bench press, and hip flexion/extension exercise in a supine orientation.

  15. Experimental 1 kW 20 cell PEFC stack

    Energy Technology Data Exchange (ETDEWEB)

    Buechi, F.N.; Marmy, C.A.; Scherer, G.G. [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Ruge, M. [Swiss Federal Inst. of Technology (ETH), Zuerich (Switzerland)

    1999-08-01

    A 20-cell PEFC stack was designed and built. Resin impregnated graphite was used as bipolar plate material. The air cooling of the stack was optimized by introducing high surface structures into the open space of the cooling plates. At {eta} (H{sub 2} LHV) = 0.5 a power of 880 W was obtained under conditions of low gas-pressures of 1.15 bar{sub a}. The auxiliary power for process air supply and cooling at 880 W power is less than 7% of the power output, indicating that the described system may be operated at a high efficiency. (author) 5 figs., 2 refs.

  16. Second Generation Small Pixel Technology Using Hybrid Bond Stacking

    Science.gov (United States)

    Venezia, Vincent C.; Hsiung, Alan Chih-Wei; Yang, Wu-Zang; Zhang, Yuying; Zhao, Cheng; Lin, Zhiqiang; Grant, Lindsay A.

    2018-01-01

    In this work, OmniVision’s second generation (Gen2) of small-pixel BSI stacking technologies is reviewed. The key features of this technology are hybrid-bond stacking, deeper back-side, deep-trench isolation, new back-side composite metal-oxide grid, and improved gate oxide quality. This Gen2 technology achieves state-of-the-art low-light image-sensor performance for 1.1, 1.0, and 0.9 µm pixel products. Additional improvements on this technology include less than 100 ppm white-pixel process and a high near-infrared (NIR) QE technology. PMID:29495272

  17. Second Generation Small Pixel Technology Using Hybrid Bond Stacking

    OpenAIRE

    Vincent C. Venezia; Alan Chih-Wei Hsiung; Wu-Zang Yang; Yuying Zhang; Cheng Zhao; Zhiqiang Lin; Lindsay A. Grant

    2018-01-01

    In this work, OmniVision’s second generation (Gen2) of small-pixel BSI stacking technologies is reviewed. The key features of this technology are hybrid-bond stacking, deeper back-side, deep-trench isolation, new back-side composite metal-oxide grid, and improved gate oxide quality. This Gen2 technology achieves state-of-the-art low-light image-sensor performance for 1.1, 1.0, and 0.9 µm pixel products. Additional improvements on this technology include less than 100 ppm white-pixel process a...

  18. Second Generation Small Pixel Technology Using Hybrid Bond Stacking

    Directory of Open Access Journals (Sweden)

    Vincent C. Venezia

    2018-02-01

    Full Text Available In this work, OmniVision’s second generation (Gen2 of small-pixel BSI stacking technologies is reviewed. The key features of this technology are hybrid-bond stacking, deeper back-side, deep-trench isolation, new back-side composite metal-oxide grid, and improved gate oxide quality. This Gen2 technology achieves state-of-the-art low-light image-sensor performance for 1.1, 1.0, and 0.9 µm pixel products. Additional improvements on this technology include less than 100 ppm white-pixel process and a high near-infrared (NIR QE technology.

  19. Second Generation Small Pixel Technology Using Hybrid Bond Stacking.

    Science.gov (United States)

    Venezia, Vincent C; Hsiung, Alan Chih-Wei; Yang, Wu-Zang; Zhang, Yuying; Zhao, Cheng; Lin, Zhiqiang; Grant, Lindsay A

    2018-02-24

    In this work, OmniVision's second generation (Gen2) of small-pixel BSI stacking technologies is reviewed. The key features of this technology are hybrid-bond stacking, deeper back-side, deep-trench isolation, new back-side composite metal-oxide grid, and improved gate oxide quality. This Gen2 technology achieves state-of-the-art low-light image-sensor performance for 1.1, 1.0, and 0.9 µm pixel products. Additional improvements on this technology include less than 100 ppm white-pixel process and a high near-infrared (NIR) QE technology.

  20. Band engineering in transition metal dichalcogenides: Stacked versus lateral heterostructures

    International Nuclear Information System (INIS)

    Guo, Yuzheng; Robertson, John

    2016-01-01

    We calculate a large difference in the band alignments for transition metal dichalcogenide (TMD) heterojunctions when arranged in the stacked layer or lateral (in-plane) geometries, using direct supercell calculations. The stacked case follows the unpinned limit of the electron affinity rule, whereas the lateral geometry follows the strongly pinned limit of alignment of charge neutrality levels. TMDs therefore provide one of the few clear tests of band alignment models, whereas three-dimensional semiconductors give less stringent tests because of accidental chemical trends in their properties.

  1. Simulation of Collective Excitations in Long Josephson Junction Stacks

    Science.gov (United States)

    Rahmonov, Ilhom; Shukrinov, Yury; Atanasova, Pavlina; Zemlyanaya, Elena; Streltsova, Oksana; Zuev, Maxim; Plecenik, Andrej; Irie, Akinobu

    2018-02-01

    The phase dynamics of a stack of long Josephson junctions has been studied. Both inductive and capacitive couplings between Josephson junctions have been taken into account in the calculations. The IV-curve, the dependence on the bias current of the radiation power and dynamics of each JJs of the stack have been investigated. The coexistence of the charge traveling wave and fluxon states has been observed. This state can be considered as a new collective excitation in the system of coupled Josephson junctions. We demonstrate that the observed collective excitation leads to the decrease of radiation power from the system.

  2. Spectrally tunable linear polarization rotation using stacked metallic metamaterials

    Science.gov (United States)

    Romain, Xavier; Baida, Fadi I.; Boyer, Philippe

    2017-08-01

    We make a theoretical study of the transmission properties of a stack of metallic metamaterials and show that is able to achieve a perfect transmission selectively exhibiting broadband (Q {10}5) polarization rotation. We especially highlight how the arrangement of the stacked structure, as well as the metamaterial unit cell geometry, has a large influence on transmission in the spectral domain. For this purpose, we use an extended analytical Jones formalism that allows us to obtain a rigorous and analytical expression of the transmission. Such versatile structures could find potential applications in polarimetry or in the control of light polarization for THz waves.

  3. Classification of calorimetric titration plots for alkyltrimethylammonium and alkylpyridinium cationic surfactants in aqueous solutions

    NARCIS (Netherlands)

    Bijma, K; Engberts, J.B.F.N.; Blandamer, M.J; Cullis, P.M.; Last, P.M.; Irlam, K.D.; Soldi, L.G.

    1997-01-01

    Calorimetric titration plots for deaggregation of micelles formed by alkylpyridinium and alkyltrimethylammonium surfactants are classified into three types, A, B and C, depending on the shape of the plot of the enthalpy of dilution as a function of surfactant concentration. For Type A plots the

  4. An ecoinformatics application for forest dynamics plot data management and sharing

    Science.gov (United States)

    Chau-Chin Lin; Abd Rahman Kassim; Kristin Vanderbilt; Donald Henshaw; Eda C. Melendez-Colom; John H. Porter; Kaoru Niiyama; Tsutomu Yagihashi; Sek Aun Tan; Sheng-Shan Lu; Chi-Wen Hsiao; Li-Wan Chang; Meei-Ru. Jeng

    2011-01-01

    Several forest dynamics plot research projects in the East-Asia Pacific region of the International Long-Term Ecological Research network actively collect long-term data, and some of these large plots are members of the Center for Tropical Forest Science network. The wealth of forest plot data presents challenges in information management to researchers. In order to...

  5. The Use of Plackett-Burman Designs to Construct Split Plot Designs.

    NARCIS (Netherlands)

    Kulahci, M.; Bisgaard, S.

    2005-01-01

    Abstract When some factors are hard to change and others are relatively easier, split-plot experiments are often an economic alternative to fully randomized designs. Split-plot experiments, with their structure of subplot arrays imbedded within whole-plot arrays, have a tendency to become large,

  6. Maintaining a permanent plot data base for growth and yield research: Solutions to some recurring problems

    Science.gov (United States)

    John C. Byrne

    1993-01-01

    Methods for solving some recurring problems of maintaining a permanent plot data base for growth and yield reseuch are described. These methods include documenting data from diverse sampling designs, changing sampling designs, changing field procedures, and coordinating activities in the plots with the land management agency. Managing a permanent plot data base (...

  7. The influence of fipronil on Reticulitermes flavipes (Isoptera: Rhinotermitidae) feeding beyond treated plots

    Science.gov (United States)

    Thomas Shelton

    2013-01-01

    A small-plot field trial was conducted to examine the area of influence of fipronil at incremental distances away from treated plots on the Harrison Experimental Forest near Saucier, MS. Small treated (water and fipronil) plots were surrounded by untreated wooden boards in an eight-point radial pattern, and examined for evidence of termite feeding every 60 d for 1 yr...

  8. Using canopy resistance for infrared heater control when warming open-field plots

    Science.gov (United States)

    Several research groups are using or planning to use arrays of infrared heaters to simulate global warming in open-field plots with a control strategy that involves maintaining a constant rise in canopy temperatures of the heated plots above those of un-heated Reference plots. . However, if the warm...

  9. A K-sample Homogeneity Test based on the Quantification of the p-p Plot

    NARCIS (Netherlands)

    Hinloopen, Jeroen; Wagenvoort, Rien; Marrewijk, van Charles

    2008-01-01

    We propose a quantification of the p-p plot that assigns equal weight to all distances between the respective distributions: the surface between the p-p plot and the diagonal. This surface is labelled the Harmonic Weighted Mass (HWM) index. We introduce the diagonal-deviation (d-d) plot that allows

  10. A K-sample Homogeneity Test based on the Quantification of the p-p Plot

    NARCIS (Netherlands)

    J. Hinloopen (Jeroen); R. Wagenvoort (Rien); J.G.M. van Marrewijk (Charles)

    2008-01-01

    textabstractWe propose a quantification of the p-p plot that assigns equal weight to all distances between the respective distributions: the surface between the p-p plot and the diagonal. This surface is labelled the Harmonic Weighted Mass (HWM) index. We introduce the diagonal-deviation (d-d) plot

  11. Variable Selection Strategies for Small-area Estimation Using FIA Plots and Remotely Sensed Data

    Science.gov (United States)

    Andrew Lister; Rachel Riemann; James Westfall; Mike Hoppus

    2005-01-01

    The USDA Forest Service's Forest Inventory and Analysis (FIA) unit maintains a network of tens of thousands of georeferenced forest inventory plots distributed across the United States. Data collected on these plots include direct measurements of tree diameter and height and other variables. We present a technique by which FIA plot data and coregistered...

  12. Multilocational evaluation of white yam genotypes using GGE bi-plot ...

    African Journals Online (AJOL)

    Five new white yam genotypes were evaluated in different locations of major yam producing areas; Umudike, Nsukka, Ubiaja, Abuja and Katsina-Ala, to test the performance and stability of these genotypes across the environments using GGE bi-plot software. The GGE bi-plot generated several graphic bi-plots which ...

  13. Practical Considerations When Using Perturbed Forest Inventory Plot Locations To Develop Spatial Models: A Case Study

    Science.gov (United States)

    John W. Coulston; Gregory A. Reams; Ronald E. McRoberts; William D. Smith

    2006-01-01

    U.S. Department of Agriculture Forest Service Forest Inventory and Analysis plot information is used in many capacities including timber inventories, forest health assessments, and environmental risk analyses. With few exceptions, actual plot locations cannot be revealed to the general public. The public does, however, have access to perturbed plot coordinates. The...

  14. Modeling post-fire woody carbon dynamics with data from remeasured inventory plots

    Science.gov (United States)

    Bianca N.I. Eskelson; Jeremy Fried; Vicente Monleon

    2015-01-01

    In California, the Forest Inventory and Analysis (FIA) plots within large fires were visited one year after the fire occurred resulting in a time series of measurements before and after fire. During this additional plot visit, the standard inventory measurements were augmented for these burned plots to assess fire effects. One example of the additional measurements is...

  15. On the measurement of the stacking-fault energies of face centered cubic metal and austenitic stainless steels by X-ray diffraction

    International Nuclear Information System (INIS)

    Borges, J.F.A.

    1985-01-01

    An X-rays diffraction method was applied to measure the Stacking-Fault Energies (SFE) of the AISI 304, AISI 316, AISI 347 and DIN-WERKSTOFF 1.4970 Austenitic Stainless Steels. The SFE determination plays an important role in the research of the mechanical behaviour of the Metal and Alloys, their deformation mechanisms, stability of microstructure amd electronic configuration. The method is based on the relationship between the SFE and the ratio of the Mean Square Strain to the Stacking-Fault probability. The Mean Square Strain was evaluated by Fourier Analysis of X-rays Diffraction profiles, corrected to reduce instrumental effects, followed by the application of the Warren-Averbach method to the Fourier Coefficients. The Stacking-Fault probabilities were derived from the changes of peak separations between cold-worked and annealed specimens. (author) [pt

  16. From the components to the stack. Developing and designing 5kW HT-PEFC stacks; Von der Komponente zum Stack. Entwicklung und Auslegung von HT-PEFC-Stacks der 5 kW-Klasse

    Energy Technology Data Exchange (ETDEWEB)

    Bendzulla, Anne

    2010-12-22

    The aim of the present project is to develop a stack design for a 5-kW HTPEFC system. First, the state of the art of potential materials and process designs will be discussed for each component. Then, using this as a basis, three potential stack designs with typical attributes will be developed and assessed in terms of practicality with the aid of a specially derived evaluation method. Two stack designs classified as promising will be discussed in detail, constructed and then characterized using short stack tests. Comparing the stack designs reveals that both designs are fundamentally suitable for application in a HT-PEFC system with on-board supply. However, some of the performance data differ significantly for the two stack designs. The preferred stack design for application in a HT-PEFC system is characterized by robust operating behaviour and reproducible high-level performance data. Moreover, in compact constructions (120 W/l at 60 W/kg), the stack design allows flexible cooling with thermal oil or air, which can be adapted to suit specific applications. Furthermore, a defined temperature gradient can be set during operation, allowing the CO tolerance to be increased by up to 10 mV. The short stack design developed within the scope of the present work therefore represents an ideal basis for developing a 5-kW HT-PEFC system. Topics for further research activities include improving the performance by reducing weight and/or volume, as well as optimizing the heat management. The results achieved within the framework of this work clearly show that HTPEFC stacks have the potential to play a decisive role in increasing efficiency in the future, particularly when combined with an on-board supply system. (orig.) [German] Ziel der vorliegenden Arbeit ist die Entwicklung eines Stackkonzeptes fuer ein 5 kW-HT-PEFC System. Dazu wird zunaechst fuer jede Komponente der Stand der Technik moeglicher Materialien und Prozesskonzepte diskutiert. Darauf aufbauend werden drei

  17. Influence of lidar, Landsat imagery, disturbance history, plot location accuracy, and plot size on accuracy of imputation maps of forest composition and structure

    Science.gov (United States)

    Harold S.J. Zald; Janet L. Ohmann; Heather M. Roberts; Matthew J. Gregory; Emilie B. Henderson; Robert J. McGaughey; Justin. Braaten

    2014-01-01

    This study investigated how lidar-derived vegetation indices, disturbance history from Landsat time series (LTS) imagery, plot location accuracy, and plot size influenced accuracy of statistical spatial models (nearest-neighbor imputation maps) of forest vegetation composition and structure. Nearest-neighbor (NN) imputation maps were developed for 539,000 ha in the...

  18. Long-term tree inventory data from mountain forest plots in France.

    Science.gov (United States)

    Fuhr, Marc; Cordonnier, Thomas; Courbaud, Benoît; Kunstler, Georges; Mermin, Eric; Riond, Catherine; Tardif, Pascal

    2017-04-01

    We present repeated tree measurement data from 63 permanent plots in mountain forests in France. Plot elevations range from 800 (lower limit of the montane belt) to 1942 m above sea level (subalpine belt). Forests mainly consist of pure or mixed stands dominated by European beech (Fagus sylvatica), Silver fir (Abies alba), and Norway spruce (Picea abies), in association with various broadleaved species at low elevation and with Arolla pine (Pinus cembra) at high elevation. The plot network includes 23 plots in stands that have not been managed for the last 40 years (at least) and 40 plots in plots managed according to an uneven-aged system with single-tree or small-group selection cutting. Plot sizes range from 0.2 to 1.9 ha. Plots were installed from 1994 to 2004 and remeasured two to five times during the 1994-2015 period. During the first census (installation), living trees more than 7.5 cm in dbh were identified, their diameter at breast height (dbh) was measured and their social status (strata) noted. Trees were spatially located, either with x, y, and z coordinates (40 plots) or within 0.25-ha square subplots (23 plots). In addition, in a subset of plots (58 plots), tree heights and tree crown dimensions were measured on a subset of trees and dead standing trees and stumps were included in the census. Remeasurements after installation include live tree diameters (including recruited trees), tree status (living, damaged, dead, stump), and for a subset of trees, height. At the time of establishment of the plots, plot densities range from 181 to 1328 stems/ha and plot basal areas range from 13.6 to 81.3 m 2 /ha. © 2017 by the Ecological Society of America.

  19. Sequence-dependent base-stacking stabilities guide tRNA folding energy landscapes.

    Science.gov (United States)

    Li, Rongzhong; Ge, Heming W; Cho, Samuel S

    2013-10-24

    The folding of bacterial tRNAs with disparate sequences has been observed to proceed in distinct folding mechanisms despite their structural similarity. To explore the folding landscapes of tRNA, we performed ion concentration-dependent coarse-grained TIS model MD simulations of several E. coli tRNAs to compare their thermodynamic melting profiles to the classical absorbance spectra of Crothers and co-workers. To independently validate our findings, we also performed atomistic empirical force field MD simulations of tRNAs, and we compared the base-to-base distances from coarse-grained and atomistic MD simulations to empirical base-stacking free energies. We then projected the free energies to the secondary structural elements of tRNA, and we observe distinct, parallel folding mechanisms whose differences can be inferred on the basis of their sequence-dependent base-stacking stabilities. In some cases, a premature, nonproductive folding intermediate corresponding to the Ψ hairpin loop must backtrack to the unfolded state before proceeding to the folded state. This observation suggests a possible explanation for the fast and slow phases observed in tRNA folding kinetics.

  20. Compact Shorted Stacked-Patch Antenna Integrated with Chip-Package Based on LTCC Technology

    Directory of Open Access Journals (Sweden)

    Yongjiu Li

    2014-01-01

    Full Text Available A low profile chip-package stacked-patch antenna is proposed by using low temperature cofired ceramic (LTCC technology. The proposed antenna employs a stacked-patch to achieve two operating frequency bands and enhance the bandwidth. The height of the antenna is decreased to 4.09 mm (about λ/25 at 2.45 GHz due to the shorted pin. The package is mounted on a 44 × 44 mm2 ground plane to miniaturize the volume of the system. The design parameters of the antenna and the effect of the antenna on chip-package cavity are carefully analyzed. The designed antenna operates at a center frequency of 2.45 GHz and its impedance bandwidth (S11< -10 dB is 200 MHz, resulting from two neighboring resonant frequencies at 2.41 and 2.51 GHz, respectively. The average gain across the frequency band is about 5.28 dBi.

  1. Spectral-spatial classification of hyperspectral data with mutual information based segmented stacked autoencoder approach

    Science.gov (United States)

    Paul, Subir; Nagesh Kumar, D.

    2018-04-01

    Hyperspectral (HS) data comprises of continuous spectral responses of hundreds of narrow spectral bands with very fine spectral resolution or bandwidth, which offer feature identification and classification with high accuracy. In the present study, Mutual Information (MI) based Segmented Stacked Autoencoder (S-SAE) approach for spectral-spatial classification of the HS data is proposed to reduce the complexity and computational time compared to Stacked Autoencoder (SAE) based feature extraction. A non-parametric dependency measure (MI) based spectral segmentation is proposed instead of linear and parametric dependency measure to take care of both linear and nonlinear inter-band dependency for spectral segmentation of the HS bands. Then morphological profiles are created corresponding to segmented spectral features to assimilate the spatial information in the spectral-spatial classification approach. Two non-parametric classifiers, Support Vector Machine (SVM) with Gaussian kernel and Random Forest (RF) are used for classification of the three most popularly used HS datasets. Results of the numerical experiments carried out in this study have shown that SVM with a Gaussian kernel is providing better results for the Pavia University and Botswana datasets whereas RF is performing better for Indian Pines dataset. The experiments performed with the proposed methodology provide encouraging results compared to numerous existing approaches.

  2. REDUCTION OF EVANGELICAL "PLOTS" IN MODERN ORTHODOX FICTION

    Directory of Open Access Journals (Sweden)

    Marina Sergeevna Krаsnyakova

    2014-11-01

    Full Text Available The article analyzes the works of contemporary authors, representing a particular artistic direction — Orthodox fi ction developed in the Russian literature for the last decades, the interpretation of biblical motifs in a literary text. Evangelical plots and motifs are demanded in modern fi ction, they determine a special structure of narration. The storyline built on the basis of autobiographical material in works of authors-priests mainly keeps the initial parabolic structure most closely resembling the primary source. Devine Providence is comprehended as execution of a request and a prayer of the person who is initially trust the Meanings contained in Gospel. In the works of secular authors the situation of illusion, showing the state of soulless modern society become emblematic. A parabolic story still requires the author's interpretation, based on the desire of a modern writer to expose moral pathos of the work. There appears a keynote of a miraculous effect of Devine Providence on human destiny. Analytical materials for the article were A. Vladimirov`s book From height of bird's fl ight, stories Feast by M. Yakovlev and Fishers of men by V. Krupin.

  3. B0 --> K+ pi- pi0 Dalitz Plot Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Z

    2004-08-16

    The authors present preliminary results on the Dalitz plot analysis of B{sup 0} --> K{sup +}{pi}{sup -}{pi}{sup 0} decays. The data sample comprises 213 million {Upsilon}(4S) --> B{bar B} decays collected with the BABAR detector at the PEP-II asymmetric-energy B Factory at SLAC. They report measurements of the inclusive branching fraction, quasi-two-body fractions and CP-violating charge asymmetries for intermediate states including K*(892){sup +}{pi}{sup -} and {rho}(770){sup -}K{sup +}. Observations of B{sup 0} decays to the K{pi}S-wave intermediate states, K{sub 0}*(1430){sup +}{pi}{sup -} and K{sub 0}*(1430){sup 0}{pi}{sup 0}, are reported. Evidence of the decay B{sup 0} --> K*(892){sup 0}{pi}{sup 0} is seen. They set upper limits at 90% confidence level on branching fractions of the nonresonant and other less significant intermediate states.

  4. The imprint of exile through the plot of the narratives

    Directory of Open Access Journals (Sweden)

    Silvia Dutrénit Bielous

    2010-06-01

    Full Text Available Exile is a circumstance different from other migrations, although it resembles them in the possible insertion or alienation from the receiving society. It is with no a doubt a forced migration process which is always accompanied by an idea and an imaginary: the disappearrance of the conditions that forced to exile and thus, the return.Although it is not possible to generalize, because there is no one single experience of exile and the subjectivities that compose it are diverse, it undoubtedly produces a sensation of alienation, which can lead to the rejection of the cultural norms of society; it is part of a process of “being in one place, but thinking about another.” However, as exile is prolonged, the experience of adaptation for the different generations involved becomes diversified, communication vessels develop, feelings of inclusion, of adaptation, of attachment with the social and cultural environment that the place of refuge offered.The present text builds on testimonies of Uruguayans exiled in Mexico who have returned to their country. In their narrative, the meanings that relate to the subjective perspective that provoked the “return” to their country of origin as being viable and a palpable event are perceived. In summary, an incursion through the testimonial plot explains to what extent the return is a recovery of the space of identity longed for and the subsequent abandonment of the foreign space, in other words, it adds to the perspective of identity as a dynamic and relational construction.

  5. An Exact Method for the Double TSP with Multiple Stacks

    DEFF Research Database (Denmark)

    Larsen, Jesper; Lusby, Richard Martin; Ehrgott, Matthias

    The double travelling salesman problem with multiple stacks (DTSPMS) is a pickup and delivery problem in which all pickups must be completed before any deliveries can be made. The problem originates from a real-life application where a 40 foot container (configured as 3 columns of 11 rows) is used...

  6. An Exact Method for the Double TSP with Multiple Stacks

    DEFF Research Database (Denmark)

    Lusby, Richard Martin; Larsen, Jesper; Ehrgott, Matthias

    2010-01-01

    The double travelling salesman problem with multiple stacks (DTSPMS) is a pickup and delivery problem in which all pickups must be completed before any deliveries can be made. The problem originates from a real-life application where a 40 foot container (configured as 3 columns of 11 rows) is used...

  7. Hydrothermal synthesis and photoluminescent properties of stacked indium sulfide superstructures.

    Science.gov (United States)

    Xing, Yan; Zhang, Hongjie; Song, Shuyan; Feng, Jing; Lei, Yongqian; Zhao, Lijun; Li, Meiye

    2008-03-28

    Unusual hierarchical stacked superstructures of cubic beta-In2S3 were fabricated via a facile hydrothermal process in the presence of a surfactant cetyltrimethylammonium bromide CTAB; the 3D superstructures were developed by helical propagation of surface steps from microflakes of 10-20 nm thickness.

  8. Phase locked fluxon-antifluxon states in stacked Josephson junctions

    DEFF Research Database (Denmark)

    Carapella, Giovanni; Constabile, Giovanni; Petraglia, Antonio

    1996-01-01

    Measurements were made on a two-stack long Josephson junction with very similar parameters and electrical access to the thin middle electrode. Mutually phase-locked fluxon-antifluxon states were observed. The observed propagation velocity is in agreement with the theoretical prediction. The I-V c...... in the junctions coexist with fluxons. (C) 1996 American Institute of Physics....

  9. Compactifications of reductive groups as moduli stacks of bundles

    DEFF Research Database (Denmark)

    Martens, Johan; Thaddeus, Michael

    Let G be a reductive group. We introduce the moduli problem of "bundle chains" parametrizing framed principal G-bundles on chains of lines. Any fan supported in a Weyl chamber determines a stability condition on bundle chains. Its moduli stack provides an equivariant toroidal compactification of G...

  10. Rhythmic ring–ring stacking drives the circadian oscillator clockwise

    Science.gov (United States)

    Chang, Yong-Gang; Tseng, Roger; Kuo, Nai-Wei; LiWang, Andy

    2012-01-01

    The oscillator of the circadian clock of cyanobacteria is composed of three proteins, KaiA, KaiB, and KaiC, which together generate a self-sustained ∼24-h rhythm of phosphorylation of KaiC. The mechanism propelling this oscillator has remained elusive, however. We show that stacking interactions between the CI and CII rings of KaiC drive the transition from the phosphorylation-specific KaiC–KaiA interaction to the dephosphorylation-specific KaiC–KaiB interaction. We have identified the KaiB-binding site, which is on the CI domain. This site is hidden when CI domains are associated as a hexameric ring. However, stacking of the CI and CII rings exposes the KaiB-binding site. Because the clock output protein SasA also binds to CI and competes with KaiB for binding, ring stacking likely regulates clock output. We demonstrate that ADP can expose the KaiB-binding site in the absence of ring stacking, providing an explanation for how it can reset the clock. PMID:22967510

  11. Rhythmic ring-ring stacking drives the circadian oscillator clockwise.

    Science.gov (United States)

    Chang, Yong-Gang; Tseng, Roger; Kuo, Nai-Wei; LiWang, Andy

    2012-10-16

    The oscillator of the circadian clock of cyanobacteria is composed of three proteins, KaiA, KaiB, and KaiC, which together generate a self-sustained ∼24-h rhythm of phosphorylation of KaiC. The mechanism propelling this oscillator has remained elusive, however. We show that stacking interactions between the CI and CII rings of KaiC drive the transition from the phosphorylation-specific KaiC-KaiA interaction to the dephosphorylation-specific KaiC-KaiB interaction. We have identified the KaiB-binding site, which is on the CI domain. This site is hidden when CI domains are associated as a hexameric ring. However, stacking of the CI and CII rings exposes the KaiB-binding site. Because the clock output protein SasA also binds to CI and competes with KaiB for binding, ring stacking likely regulates clock output. We demonstrate that ADP can expose the KaiB-binding site in the absence of ring stacking, providing an explanation for how it can reset the clock.

  12. Revisiting the Fundamentals and Capabilities of the Stack Compression Test

    DEFF Research Database (Denmark)

    Alves, L.M.; Nielsen, Chris Valentin; Martin, P.A.F.

    2011-01-01

    performance by comparing the flow curves obtained from its utilisation with those determined by means of compressive testing carried out on solid cylinder specimens of the same material. Results show that mechanical testing of materials by means of the stack compression test is capable of meeting...... the increasing demand of accurate and reliable flow curves for sheet metals....

  13. Tunable infrared plasmonic devices using graphene/insulator stacks

    Science.gov (United States)

    Yan, Hugen; Li, Xuesong; Chandra, Bhupesh; Tulevski, George; Wu, Yanqing; Freitag, Marcus; Zhu, Wenjuan; Avouris, Phaedon; Xia, Fengnian

    2012-05-01

    The collective oscillation of carriers--the plasmon--in graphene has many desirable properties, including tunability and low loss. However, in single-layer graphene, the dependence on carrier concentration of both the plasmonic resonance frequency and magnitude is relatively weak, limiting its applications in photonics. Here, we demonstrate transparent photonic devices based on graphene/insulator stacks, which are formed by depositing alternating wafer-scale graphene sheets and thin insulating layers, then patterning them together into photonic-crystal-like structures. We show experimentally that the plasmon in such stacks is unambiguously non-classical. Compared with doping in single-layer graphene, distributing carriers into multiple graphene layers effectively enhances the plasmonic resonance frequency and magnitude, which is different from the effect in a conventional semiconductor superlattice and is a direct consequence of the unique carrier density scaling law of the plasmonic resonance of Dirac fermions. Using patterned graphene/insulator stacks, we demonstrate widely tunable far-infrared notch filters with 8.2 dB rejection ratios and terahertz linear polarizers with 9.5 dB extinction ratios. An unpatterned stack consisting of five graphene layers shields 97.5% of electromagnetic radiation at frequencies below 1.2 THz. This work could lead to the development of transparent mid- and far-infrared photonic devices such as detectors, modulators and three-dimensional metamaterial systems.

  14. Stacked-Bloch-wave electron diffraction simulations using GPU acceleration

    International Nuclear Information System (INIS)

    Pennington, Robert S.; Wang, Feng; Koch, Christoph T.

    2014-01-01

    In this paper, we discuss the advantages for Bloch-wave simulations performed using graphics processing units (GPUs), based on approximating the matrix exponential directly instead of performing a matrix diagonalization. Our direct matrix-exponential algorithm yields a functionally identical electron scattering matrix to that generated with matrix diagonalization. Using the matrix-exponential scaling-and-squaring method with a Padé approximation, direct GPU-based matrix-exponential double-precision calculations are up to 20× faster than CPU-based calculations and up to approximately 70× faster than matrix diagonalization. We compare precision and runtime of scaling and squaring methods with either the Padé approximation or a Taylor expansion. We also discuss the stacked-Bloch-wave method, and show that our stacked-Bloch-wave implementation yields the same electron scattering matrix as traditional Bloch-wave matrix diagonalization. - Highlights: • Bloch-wave and stacked-Bloch-wave calculations can be accelerated with GPUs. • Direct approximation of the matrix exponential can be faster than diagonalization. • GPU-based direct approximation can be ≈70× faster than CPU diagonalization. • Larger matrices benefit more from this approach than smaller ones. • Stacked-Bloch-wave scattering results are functionally identical to diagonalization

  15. Do Identical Polar Diatomic Molecules Form Stacked or Linear ...

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 19; Issue 8. Do Identical Polar Diatomic Molecules Form Stacked or Linear Dimers?: Hydrogen Bonding is Not Just Dipole-Dipole Interactions. C W Williams Richard N Zare E Arunan. General Article Volume 19 Issue 8 August 2014 pp 704-712 ...

  16. 7. Data Structures: Lists, Queues, Stacks and Arrays

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 2; Issue 6. Algorithms - Data Structures: Lists, Queues, Stacks and Arrays. R K Shyamasundar ... Author Affiliations. R K Shyamasundar1. Computer Science Group, Tata Institute of Fundamental Research, Homi Bhabha Road, Mumbai 400 005, India ...

  17. Thermal entrance effects in a thermoacoustic stacked screen regenerator

    NARCIS (Netherlands)

    Bühler, Simon; wilcox, D; Oosterhuis, Joris; van der Meer, Theodorus H.

    2014-01-01

    Thermoacoustic cryocoolers are of raising interest because they are cost effective and reliable. The underlying heat pumping process occurs in the regenerator, where a sound wave interacts with a solid matrix material. Stacked screens are frequently used to build regenerators for thermoacoustic

  18. Proposal of stack Effect technology for predicted future years

    Science.gov (United States)

    Teddy Badai Samodra, FX; Adi Indrawan, Iwan

    2017-12-01

    Recently, stack effect is a general problem solver in providing vertical ventilation for urban environmental issues. However, study on resilient technology of stack effect for future years as predicted by climate trend should be conducted. Therefore, this research proposes a design of new technology on operable and adaptable vertical ventilation to the environmental change. The research method is conducted by comprehensive simulation of Ecotect Analysis, ANSYS Fluent and Matlab. Urban environment of Surabaya, as the research location, is the representative of tropical region. The results showed that the stack effect height and area could be modified instantly adjusting the environmental condition time by time in the future years. With 1.8 m of stack width, the proposed technology could capture 40 m3 of vertical air flow which is useful for physiological cooling and its dimension could be modified depending on the environmental condition. By providing resilient technology, predictable and sustainable ventilation method is offered to anticipate an unpredicted global warming and environmental change.

  19. Multipole stack for the 4 rings of the PS Booster

    CERN Multimedia

    CERN PhotoLab

    1976-01-01

    The PS Booster (originally 800 MeV, now 1.4 GeV) saw first beam in 1972, routine operation began in 1973. The strive for ever higher intensities required the addition of multipoles. Manufacture of 8 stacks of multipoles was launched in 1974, for installation in 1976. For details, see 7511120X.

  20. Consolidation process model for film stacking glass/PPS laminates

    NARCIS (Netherlands)

    Grouve, Wouter Johannes Bernardus; Akkerman, Remko

    2010-01-01

    A model is proposed to optimise the processing parameters for the consolidation of glass/polyphenylene sulphide (PPS) laminates using a film stacking procedure. In a split approach, the heating and consolidation phase are treated separately. The heating phase is modelled using the one-dimensional

  1. 7. Data Structures: Lists, Queues, Stacks and Arrays

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 2; Issue 6. Algorithms - Data Structures: Lists, Queues, Stacks and Arrays. R K Shyamasundar. Series Article Volume 2 Issue 6 June 1997 pp 39-46. Fulltext. Click here to view fulltext PDF. Permanent link:

  2. Calculating the output distribution of stack filters that are erosion ...

    African Journals Online (AJOL)

    Two procedures to compute the output distribution ϕs of certain stack filters S (so called erosion-dilation cascades) are given. One rests on the disjunctive normal form of S and also yields the rank selection probabilities. The other is based on inclusion-exclusion and e.g. yields ϕs for some important LULU-operators S.

  3. Precise stacking and bonding technology for RDDS structure

    International Nuclear Information System (INIS)

    Higo, T; Toge, N.; Suzuki, T.

    2000-01-01

    The X-band accelerating structures called RDDS1 (Rounded Dumped Detuned Structure) for the linear collider have been developed. The main body of RDDS1 was successfully fabricated in Japan (KEK, IHI). We established basic fabrication techniques through the development of prototype structures including RDDS1. The precise stacking and bonding technologies for RDDS structure are presented in this paper. (author)

  4. Comparison of Three Plot Selection Methods for Estimating Change in Temporally Variable, Spatially Clustered Populations.

    Energy Technology Data Exchange (ETDEWEB)

    Thompson, William L. [Bonneville Power Administration, Portland, OR (US). Environment, Fish and Wildlife

    2001-07-01

    Monitoring population numbers is important for assessing trends and meeting various legislative mandates. However, sampling across time introduces a temporal aspect to survey design in addition to the spatial one. For instance, a sample that is initially representative may lose this attribute if there is a shift in numbers and/or spatial distribution in the underlying population that is not reflected in later sampled plots. Plot selection methods that account for this temporal variability will produce the best trend estimates. Consequently, I used simulation to compare bias and relative precision of estimates of population change among stratified and unstratified sampling designs based on permanent, temporary, and partial replacement plots under varying levels of spatial clustering, density, and temporal shifting of populations. Permanent plots produced more precise estimates of change than temporary plots across all factors. Further, permanent plots performed better than partial replacement plots except for high density (5 and 10 individuals per plot) and 25% - 50% shifts in the population. Stratified designs always produced less precise estimates of population change for all three plot selection methods, and often produced biased change estimates and greatly inflated variance estimates under sampling with partial replacement. Hence, stratification that remains fixed across time should be avoided when monitoring populations that are likely to exhibit large changes in numbers and/or spatial distribution during the study period. Key words: bias; change estimation; monitoring; permanent plots; relative precision; sampling with partial replacement; temporary plots.

  5. Development and Applications of a Stage Stacking Procedure

    Science.gov (United States)

    Kulkarni, Sameer; Celestina, Mark L.; Adamczyk, John J.

    2012-01-01

    The preliminary design of multistage axial compressors in gas turbine engines is typically accomplished with mean-line methods. These methods, which rely on empirical correlations, estimate compressor performance well near the design point, but may become less reliable off-design. For land-based applications of gas turbine engines, off-design performance estimates are becoming increasingly important, as turbine plant operators desire peaking or load-following capabilities and hot-day operability. The current work develops a one-dimensional stage stacking procedure, including a newly defined blockage term, which is used to estimate the off-design performance and operability range of a 13-stage axial compressor used in a power generating gas turbine engine. The new blockage term is defined to give mathematical closure on static pressure, and values of blockage are shown to collapse to curves as a function of stage inlet flow coefficient and corrected shaft speed. In addition to these blockage curves, the stage stacking procedure utilizes stage characteristics of ideal work coefficient and adiabatic efficiency. These curves are constructed using flow information extracted from computational fluid dynamics (CFD) simulations of groups of stages within the compressor. Performance estimates resulting from the stage stacking procedure are shown to match the results of CFD simulations of the entire compressor to within 1.6% in overall total pressure ratio and within 0.3 points in overall adiabatic efficiency. Utility of the stage stacking procedure is demonstrated by estimation of the minimum corrected speed which allows stable operation of the compressor. Further utility of the stage stacking procedure is demonstrated with a bleed sensitivity study, which estimates a bleed schedule to expand the compressors operating range.

  6. Hydrodynamic Modelling and Experimental Analysis of FE-DMFC Stacks

    Science.gov (United States)

    Kablou, Yashar

    Direct methanol fuel cells (DMFCs) present some unique features such as having liquid fuel, quick refueling process, compact design and high energy density. These characteristics make them incredibly suitable as a promising power source for portable electronic applications, such as cell phones or laptop computers. Despite of these positive aspects, the commercial development of DMFCs has nevertheless been hindered by some important issues such as, carbon dioxide formation at the anode compartment and, methanol crossover through the membrane. Many researchers have tried to model the two-phase flow behavior inside the DMFC anode compartment using the "homogenous flow modelling" approach, which has proven to be inaccurate specially when dealing with DMFC stacks. On the other hand, several strategies to prevent methanol crossover have been suggested in the literature, including the use of a flowing electrolyte between the DMFC anode and cathode compartments. Preliminary tests on flowing electrolyte direct methanol fuel cells (FE-DMFCs) have shown promising results; however, further investigation should be carried out on the stack level. In the first part of this study, a quasi two-dimensional numerical model was developed, to predict the two-phase flow behavior within the DMFC anode compartment, both in single cell and stack levels. Various types of flow modelling approaches and void fraction correlations were utilized to estimate the pressure drop across the anode compartment. It was found that the "separated flow modelling" approach, as well as CISE correlation for void fraction (developed at the CISE labs in Milan), yield the best results. In the second part, a five-cell FE-DMFC stack unit with a parallel serpentine flow bed design and U-type manifold configuration, was developed and tested at various operating conditions. It was found that, the flowing electrolyte effectively reduced methanol crossover and, improved the stack performance.

  7. Study on the polarity, solubility, and stacking characteristics of asphaltenes

    KAUST Repository

    Zhang, Long-li

    2014-07-01

    The structure and transformation of fused aromatic ring system in asphaltenes play an important role in the character of asphaltenes, and in step affect the properties of heavy oils. Polarity, solubility and structural characteristics of asphaltenes derived from Tahe atmospheric residue (THAR) and Tuo-826 heavy crude oil (Tuo-826) were analyzed for study of their internal relationship. A fractionation method was used to separate the asphaltenes into four sub-fractions, based on their solubility in the mixed solvent, for the study of different structural and physical-chemical properties, such as polarity, solubility, morphology, stacking characteristics, and mean structural parameters. Transmission electron microscope (TEM) observation can present the intuitive morphology of asphaltene molecules, and shows that the structure of asphaltenes is in local order as well as long range disorder. The analysis results showed that n-heptane asphaltenes of THAR and Tuo-826 had larger dipole moment values, larger fused aromatic ring systems, larger mean number of stacking layers, and less interlayer spacing between stacking layers than the corresponding n-pentane asphaltenes. The sub-fractions that were inclined to precipitate from the mixture of n-heptane and tetrahydrofuran had larger polarity and less solubility. From the first sub-fraction to the fourth sub-fraction, polarity, mean stacking numbers, and average layer size from the TEM images follow a gradual decrease. The structural parameters derived from TEM images could reflect the largest fused aromatic ring system in asphaltene molecule, yet the parameters derived from 1H NMR data reflected the mean message of poly-aromatic ring systems. The structural parameters derived from TEM images were more consistent with the polarity variation of sub-fractions than those derived from 1H NMR data, which indicates that the largest fused aromatic ring system will play a more important role in the stacking characteristics of

  8. Do Stacked Species Distribution Models Reflect Altitudinal Diversity Patterns?

    Science.gov (United States)

    Mateo, Rubén G.; Felicísimo, Ángel M.; Pottier, Julien; Guisan, Antoine; Muñoz, Jesús

    2012-01-01

    The objective of this study was to evaluate the performance of stacked species distribution models in predicting the alpha and gamma species diversity patterns of two important plant clades along elevation in the Andes. We modelled the distribution of the species in the Anthurium genus (53 species) and the Bromeliaceae family (89 species) using six modelling techniques. We combined all of the predictions for the same species in ensemble models based on two different criteria: the average of the rescaled predictions by all techniques and the average of the best techniques. The rescaled predictions were then reclassified into binary predictions (presence/absence). By stacking either the original predictions or binary predictions for both ensemble procedures, we obtained four different species richness models per taxa. The gamma and alpha diversity per elevation band (500 m) was also computed. To evaluate the prediction abilities for the four predictions of species richness and gamma diversity, the models were compared with the real data along an elevation gradient that was independently compiled by specialists. Finally, we also tested whether our richness models performed better than a null model of altitudinal changes of diversity based on the literature. Stacking of the ensemble prediction of the individual species models generated richness models that proved to be well correlated with the observed alpha diversity richness patterns along elevation and with the gamma diversity derived from the literature. Overall, these models tend to overpredict species richness. The use of the ensemble predictions from the species models built with different techniques seems very promising for modelling of species assemblages. Stacking of the binary models reduced the over-prediction, although more research is needed. The randomisation test proved to be a promising method for testing the performance of the stacked models, but other implementations may still be developed. PMID

  9. Detent torque from the soft magnetic stator stack of a hybrid stepper motor

    Science.gov (United States)

    Rajagopal, K. R.; Singh, Bhim; Singh, B. P.

    2003-05-01

    The residual magnetism present in the stator stack of a hybrid stepper motor, which will be of the last excited polarity, will develop a detent torque, similar to the static torque of the last excited phase, but with reduced excitation. The predominant component is fundamental. Even though this torque is the result of the stator excitation, it can be considered as a detent torque as it is available when the stator excitation is withdrawn. This detent torque is in addition to the inherent one due to the rotor permanent magnet, and it will be present until the next phase is switched ON. Once the excitation is removed from the second phase, because of the hysteresis the detent torque will be available, similar to the static torque profile for phase 2, but with less excitation. This means because of the hysteresis the detent torque follows the static torque of the phases. The magnitude of this detent torque will depend upon the level to which the phase was excited. Experiments have been carried out on a 0.5° hybrid stepper motor to study the effects of the excitation on the detent torque profiles. Harmonic analyses of the measured detent torque curves had been carried out and it is seen that the fundamental detent torque increases with the excitation and also follows the respective phases. Therefore, the residual flux density and the coercive force of the soft magnetic material used for the stator stack have to be as small as possible to get rid of this effect. Controlling a hybrid stepper motor by a suitable switching scheme for a given application requires the measured static torque profiles of the motor for all the phases at the exact working voltage (or voltages in case of a variable voltage supply) and detent torque profiles both before and after excitation. Harmonic spectrum of the measured static and detent torque profiles have to be accounted for while simulating stepping behavior of the motor, from which an appropriate switching scheme can be arrived at.

  10. Measurements of the effectiveness of conservation agriculture at the field scale using radioisotopic techniques and runoff plots

    Science.gov (United States)

    Mabit, L.; Klik, A.; Toloza, A.; Benmansour, M.; Geisler, A.; Gerstmann, U. C.

    2009-04-01

    Growing evidence of the cost of soil erosion on agricultural land and off site impact of associated processes has emphasized the needs for quantitative assessment of erosion rates to develop and assess erosion control technology and to allocate conservation resources and development of conservation regulation, policies and programmes. Our main study goal was to assess the magnitude of deposition rates using Fallout Radionuclides ‘FRNs' (137-Cs and 210-Pb) and the mid-term (13 years) erosion rates using conventional runoff plot measurements in a small agricultural watershed under conventional and conservation tillage practices. The tillage treatments were conventional tillage system (CT), mechanical plough to 30 cm depth (the most common tillage system within the watershed); conservation tillage (CS) with cover crops during winter; and direct seeding (DS) no tillage with cover crops during winter. The experimental design - located in Mistelbach watershed 60 km north of Vienna/Austria - consists of one 3-metre-wide and 15-metre-long runoff plot (silt loam - slope of 14%) for each tillage system (CT, CS and DS) with the plots placed in the upper part of an agricultural field. 76 soil samples were collected to evaluate the initial fallout of 137-Cs and 210-Pb in a small forested area close to the experimental field, along a systematic multi-grid design,. In the sedimentation area of the watershed and down slope the agricultural field, 2 additional soil profiles were collected to 1 m depth. All soil samples were air dried, sieved to 2mm and analysed for their 137-Cs and 210-Pb contents using gamma detector. The main results and conclusion can be summarised as following: i) The initial 137-Cs fallout as measured in the 76 forested soil samples ranged from 1123 to 3354 Bq/m2 for an average of 1954 Bq/m2 with a coefficient of variation of 20.4 %. ii) Long-term erosion measurements (1994-2006) from runoff plots located in the upper part of the agricultural field just up

  11. Design and Fabrication of Complex Scaffolds for Bone Defect Healing: Combined 3D Plotting of a Calcium Phosphate Cement and a Growth Factor-Loaded Hydrogel.

    Science.gov (United States)

    Ahlfeld, Tilman; Akkineni, Ashwini Rahul; Förster, Yvonne; Köhler, Tino; Knaack, Sven; Gelinsky, Michael; Lode, Anja

    2017-01-01

    Additive manufacturing enables the fabrication of scaffolds with defined architecture. Versatile printing technologies such as extrusion-based 3D plotting allow in addition the incorporation of biological components increasing the capability to restore functional tissues. We have recently described the fabrication of calcium phosphate cement (CPC) scaffolds by 3D plotting of an oil-based CPC paste under mild conditions. In the present study, we have developed a strategy for growth factor loading based on multichannel plotting: a biphasic scaffold design was realised combining CPC with VEGF-laden, highly concentrated hydrogel strands. As hydrogel component, alginate and an alginate-gellan gum blend were evaluated; the blend exhibited a more favourable VEGF release profile and was chosen for biphasic scaffold fabrication. After plotting, two-step post-processing was performed for both, hydrogel crosslinking and CPC setting, which was shown to be compatible with both materials. Finally, a scaffold was designed and fabricated which can be applied for testing in a rat critical size femur defect. Optimization of CPC plotting enabled the fabrication of highly resolved structures with strand diameters of only 200 µm. Micro-computed tomography revealed a precise strand arrangement and an interconnected pore space within the biphasic scaffold even in swollen state of the hydrogel strands.

  12. Incomplete split-plot designs based on alpha-designs: a compromise between traditional split-plot designs and randomised complete block design

    DEFF Research Database (Denmark)

    Kristensen, Kristian

    2012-01-01

    The paper shows how the α-design (also known as generalised lattice) may be used for constructing incomplete split-plot designs and describes four different methods (A, B, C and D) of construction. Intra-block efficiency factors and theoretical considerations are used to compare the methods. Based...... of data. The three types were simulated data with known covariance structure, data from uniformity trials and data from actual trials using incomplete split-plot designs for comparing cereal varieties under different growing conditions. It is concluded that the incomplete split-plot designs may be a good...

  13. THERAPIE - THErmix-RAps-Plot-InterfacE. A graphic software for representation of THERMIX-2D results with the interactive plot program RAPS

    International Nuclear Information System (INIS)

    Duensing, P.; Jahn, W.; Rehm, W.

    1986-09-01

    The performance of safety analyses for gas-cooled high temperature reactor power plants requires efficient plot codes for the evaluation and representation of computer results. The report describes the coupling between the thermodynamic simulation code THERMIX and the graphic plot code RAPS via the interface program THERAPIE. Especially the structure and the handling of the interface program are explained as well as the dialogue with the plot code. Further options of the colour graphic system are demonstrated for the representation of temperature distributions in components of HTR concepts (HTR-500). (orig.) [de

  14. Operation of a Five-Stage 40,000-CM2-Area Insulator Stack at 158 KV/CM

    International Nuclear Information System (INIS)

    We have demonstrated successful operation of a 3.35- m-diameter insulator stack at 158 kV/cm on five consecutive Z-accelerator shots. The stack consisted of five +45 deg;-profile 5.715-cm-thick cross-linked-polystyrene (Rexolite- 1422) insulator rings, and four anodized- aluminum grading rings shaped to reduce the field at cathode triple junctions. The width of the voltage pulse at 89% of peak was 32 ns. We compare this result to a new empirical flashover relation developed from previous small-insulator experiments conducted with flat unanodized electrodes. The relation predicts a 50% flashover probability for a Rexolite insulator during an applied voltage pulse when E max e -0.27/d (t eff C) 1/10 = 224, where E max is the peak mean electric field (kV/cm), d is the insulator thickness (cm), t eff is the effective pulse width (ps), and C is the insulator circumference (cm). We find the Z stack can be operated at a stress at least 19% higher than predicted. This result, and previous experiments conducted by Vogtlin, suggest anodized electrodes with geometries that reduce the field at both anode and cathode triple junctions would improve the flashover strength of +45 deg; insulators

  15. User Guide for the Plotting Software for the Los Alamos National Laboratory Nuclear Weapons Analysis Tools Version 2.0

    Energy Technology Data Exchange (ETDEWEB)

    Cleland, Timothy James [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2018-01-02

    The Los Alamos National Laboratory Plotting Software for the Nuclear Weapons Analysis Tools is a Java™ application based upon the open source library JFreeChart. The software provides a capability for plotting data on graphs with a rich variety of display options while allowing the viewer interaction via graph manipulation and scaling to best view the data. The graph types include XY plots, Date XY plots, Bar plots and Histogram plots.

  16. Electronic structure of the rotation twin stacking fault in β-ZnS

    International Nuclear Information System (INIS)

    Northrup, J.E.; Cohen, M.L.

    1981-01-01

    The electronic structure of the rotation twin stacking fault in β-ZnS is calculated with the self-consistent pseudopotential method. The stacking fault creates a potential barrier of approx.0.07 eV and induces the localization of stacking-fault resonances near the top of the valence band. Stacking-fault states are also predicted to exist in the various gaps in the projected valence-band structure

  17. snp.plotter: an R-based SNP/haplotype association and linkage disequilibrium plotting package.

    Science.gov (United States)

    Luna, Augustin; Nicodemus, Kristin K

    2007-03-15

    snp.plotter is a newly developed R package which produces high-quality plots of results from genetic association studies. The main features of the package include options to display a linkage disequilibrium (LD) plot below the P-value plot using either the r2 or D' LD metric, to set the X-axis to equal spacing or to use the physical map of markers, and to specify plot labels, colors, symbols and LD heatmap color scheme. snp.plotter can plot single SNP and/or haplotype data and simultaneously plot multiple sets of results. R is a free software environment for statistical computing and graphics available for most platforms. The proposed package provides a simple way to convey both association and LD information in a single appealing graphic for genetic association studies. Downloadable R package and example datasets are available at http://cbdb.nimh.nih.gov/~kristin/snp.plotter.html and http://www.r-project.org.

  18. Investigation of Ruthenium Dissolution in Advanced Membrane Electrode Assemblies for Direct Methanol Based Fuel Cells Stacks

    Science.gov (United States)

    Valdez, T. I.; Firdosy, S.; Koel, B. E.; Narayanan, S. R.

    2005-01-01

    This viewgraph presentation gives a detailed review of the Direct Methanol Based Fuel Cell (DMFC) stack and investigates the Ruthenium that was found at the exit of the stack. The topics include: 1) Motivation; 2) Pathways for Cell Degradation; 3) Cell Duration Testing; 4) Duration Testing, MEA Analysis; and 5) Stack Degradation Analysis.

  19. The Methods of Design and Implementation of Stack Filters for Image Processing

    Directory of Open Access Journals (Sweden)

    S. Marchevsky

    1995-04-01

    Full Text Available This paper deals with a large class of nonlinear digital filters, the stack filters, which contain all combinations and compositions of rank order operators within a finite window. Attention is given to design and effective hardware implementation of an optimal stack filter for image processing. Presented simulation results confirm robustness of stack filters in the image restoration corrupted by impulsive noise.

  20. The Effect of a Sport Stacking Intervention on Handwriting with Second Grade Students

    Science.gov (United States)

    Li, Yuhua; Coleman, Diane; Ransdell, Mary; Coleman, Lyndsie; Irwin, Carol

    2014-01-01

    The present study examined the impact a 14-week sport stacking (cup stacking) exercise intervention would have on children's handwriting quality and speed. Eighty-three second graders were randomly assigned to either an experimental or a control group. The experimental group (n = 42) participated in a 15-min session of sport stacking activities…

  1. Modelling and Evaluation of Heating Strategies for High Temperature Polymer Electrolyte Membrane Fuel Cell Stacks

    DEFF Research Database (Denmark)

    Andreasen, Søren Juhl; Kær, Søren Knudsen

    2008-01-01

    Experiments were conducted on two different cathode air cooled high temperature PEM (HTPEM) fuel cell stacks; a 30 cell 400W prototype stack using two bipolar plates per cell, and a 65 cell 1 kW commercial stack using one bipolar plate per cell. The work seeks to examine the use of different...

  2. Spam comments prediction using stacking with ensemble learning

    Science.gov (United States)

    Mehmood, Arif; On, Byung-Won; Lee, Ingyu; Ashraf, Imran; Choi, Gyu Sang

    2018-01-01

    Illusive comments of product or services are misleading for people in decision making. The current methodologies to predict deceptive comments are concerned for feature designing with single training model. Indigenous features have ability to show some linguistic phenomena but are hard to reveal the latent semantic meaning of the comments. We propose a prediction model on general features of documents using stacking with ensemble learning. Term Frequency/Inverse Document Frequency (TF/IDF) features are inputs to stacking of Random Forest and Gradient Boosted Trees and the outputs of the base learners are encapsulated with decision tree to make final training of the model. The results exhibits that our approach gives the accuracy of 92.19% which outperform the state-of-the-art method.

  3. Radar Target Recognition Based on Stacked Denoising Sparse Autoencoder

    Directory of Open Access Journals (Sweden)

    Zhao Feixiang

    2017-04-01

    Full Text Available Feature extraction is a key step in radar target recognition. The quality of the extracted features determines the performance of target recognition. However, obtaining the deep nature of the data is difficult using the traditional method. The autoencoder can learn features by making use of data and can obtain feature expressions at different levels of data. To eliminate the influence of noise, the method of radar target recognition based on stacked denoising sparse autoencoder is proposed in this paper. This method can extract features directly and efficiently by setting different hidden layers and numbers of iterations. Experimental results show that the proposed method is superior to the K-nearest neighbor method and the traditional stacked autoencoder.

  4. High specific power, direct methanol fuel cell stack

    Science.gov (United States)

    Ramsey, John C [Los Alamos, NM; Wilson, Mahlon S [Los Alamos, NM

    2007-05-08

    The present invention is a fuel cell stack including at least one direct methanol fuel cell. A cathode manifold is used to convey ambient air to each fuel cell, and an anode manifold is used to convey liquid methanol fuel to each fuel cell. Tie-bolt penetrations and tie-bolts are spaced evenly around the perimeter to hold the fuel cell stack together. Each fuel cell uses two graphite-based plates. One plate includes a cathode active area that is defined by serpentine channels connecting the inlet manifold with an integral flow restrictor to the outlet manifold. The other plate includes an anode active area defined by serpentine channels connecting the inlet and outlet of the anode manifold. Located between the two plates is the fuel cell active region.

  5. Detailed experimental characterization of a reformate fuelled PEM stack

    DEFF Research Database (Denmark)

    Korsgaard, Anders; Nielsen, Mads Pagh; Kær, Søren Knudsen

    2006-01-01

    Increasing attention is given to fuel cells for micro combined heat and power systems for local households. Currently, mainly three different types of fuel cells are commercially competitive: SOFC, low- and high-temperature PEM fuel cells. In the present paper the Low Temperature PEM technology...... is in focus. To be able to design highly efficient micro CHP systems, it is critical to have a reliable performance map of not only the stack performance in the nominal operating point but also at system part load.  Issues like parasitic power consumption of the balance of plant components, dynamic...... with electric power output from 1-3-kW. All process inputs for the stack can be altered to provide realistic performance analyses, corresponding to those encountered in field applications. These include cathode/anode dew point control, cathode flow rate, cooling water temperature control as well as synthesis...

  6. STACKING ON COMMON REFLECTION SURFACE WITH MULTIPARAMETER TRAVELTIME

    Directory of Open Access Journals (Sweden)

    Montes V. Luis A.

    2006-12-01

    Full Text Available Commonly seismic images are displayed in time domain because the model in depth can be known only in well logs. To produce seismic sections, pre and post stack processing approaches use time or depth velocity models whereas the common reflection method does not, instead it requires a set of parameters established for the first layer. A set of synthetic data of an anticline model, with sources and receivers placed on a flat topography, was used to observe the performance of this method. As result, a better reflector recovering compared against conventional processing sequence was observed.
    The procedure was extended to real data, using a dataset acquired on a zone characterized by mild topography and quiet environment reflectors in the Eastern Colombia planes, observing an enhanced and a better continuity of the reflectors in the CRS stacked section.

  7. Physically Connected Stacked Patch Antenna Design with 100% Bandwidth

    KAUST Repository

    Klionovski, Kirill

    2017-11-01

    Typically, stacked patch antennas are parasitically coupled and provide larger bandwidth than a single patch antenna. Here, we show a stacked patch antenna design where square patches with semi-circular cutouts are physically connected to each other. This arrangement provides 100% bandwidth from 23.9–72.2 GHz with consistent high gain (5 dBi or more) across the entire bandwidth. In another variation, a single patch loaded with a superstrate provides 83.5% bandwidth from 25.6–62.3 GHz. The mechanism of bandwidth enhancement is explained through electromagnetic simulations. Measured reflection coefficient, radiation patterns and gain results confirm the extremely wideband performance of the design.

  8. Piezoelectric Multilayer-Stacked Hybrid Actuation/Transduction System

    Science.gov (United States)

    Xu, Tian-Bing (Inventor); Jiang, Xiaoning (Inventor); Su, Ji (Inventor)

    2014-01-01

    A novel full piezoelectric multilayer stacked hybrid actuation/transduction system. The system demonstrates significantly-enhanced electromechanical performance by utilizing the cooperative contributions of the electromechanical responses of multilayer stacked negative and positive strain components. Both experimental and theoretical studies indicate that for this system, the displacement is over three times that of a same-sized conventional flextensional actuator/transducer. The system consists of at least 2 layers which include electromechanically active components. The layers are arranged such that when electric power is applied, one layer contracts in a transverse direction while the second layer expands in a transverse direction which is perpendicular to the transverse direction of the first layer. An alternate embodiment includes a third layer. In this embodiment, the outer two layers contract in parallel transverse directions while the middle layer expands in a transverse direction which is perpendicular to the transverse direction of the outer layers.

  9. Remote Sensing Image Classification Based on Stacked Denoising Autoencoder

    Directory of Open Access Journals (Sweden)

    Peng Liang

    2017-12-01

    Full Text Available Focused on the issue that conventional remote sensing image classification methods have run into the bottlenecks in accuracy, a new remote sensing image classification method inspired by deep learning is proposed, which is based on Stacked Denoising Autoencoder. First, the deep network model is built through the stacked layers of Denoising Autoencoder. Then, with noised input, the unsupervised Greedy layer-wise training algorithm is used to train each layer in turn for more robust expressing, characteristics are obtained in supervised learning by Back Propagation (BP neural network, and the whole network is optimized by error back propagation. Finally, Gaofen-1 satellite (GF-1 remote sensing data are used for evaluation, and the total accuracy and kappa accuracy reach 95.7% and 0.955, respectively, which are higher than that of the Support Vector Machine and Back Propagation neural network. The experiment results show that the proposed method can effectively improve the accuracy of remote sensing image classification.

  10. Rain Sensor with Stacked Light Waveguide Having Tilted Air Gap

    Directory of Open Access Journals (Sweden)

    Kyoo Nam Choi

    2014-01-01

    Full Text Available Vehicle sensor to detect rain drop on and above waveguide utilizing light deflection and scattering was realized, keeping wide sensing coverage and sensitivity to detect mist accumulation. Proposed sensor structure under stacked light wave guide consisted of light blocking fixture surrounding photodetector and adjacent light source. Tilted air gap between stacked light waveguide and light blocking fixture played major role to increase sensitivity and to enhance linearity. This sensor structure eliminated complex collimating optics, while keeping wide sensing coverage using simple geometry. Detection algorithm based on time-to-intensity transformation process was used to convert raining intensity into countable raining process. Experimental result inside simulated rain chamber showed distinct different response between light rain and normal rain. Application as automobile rain sensor is expected.

  11. Stack monitor for the Proof-of-Breeding Project

    International Nuclear Information System (INIS)

    Fergus, R.W.

    1985-01-01

    This stack monitor system is a coordinated arrangement of hardware and software to monitor four hot cells (8 stacks) during the fuel dissection for the Proof-of-Breeding Project. The cell monitors, which are located in fan lofts, contain a microprocessor, radiation detectors, air flow sensors, and air flow control equipment. Design criteria included maximizing microprocessor control while minimizing the hardware complexity. The monitors have been programmed to produce concentration and total activity release data based on several detector measurements and flow rates. Although each monitor can function independently, a microcomputer can also be used to control each cell monitor including reprogramming if necessary. All programming is software, as opposed to firmware, with machine language for compactness in the cell monitors and Basic language for adaptability in the microcomputer controller

  12. The Effect of NPP's Stack Height to Radiation Dose

    International Nuclear Information System (INIS)

    Pandi, Liliana Yetta; Rohman, Budi

    2003-01-01

    The purpose of dose calculation for accidents is to analyze the capability of NPP to maintain the safety of public and workers in case an accident occurs on the Plant in a site. This paper calculates the Loss of Coolant Accident in PWR plant. The calculation results shows that no risks of serious radiation exposure are given to the neighboring public even if such a large accident occurred, and the effect of stack height can be predicted by analysis of the calculation results. The whole dose is calculated for some location (100 m, 300 m, 500 m, 700 m, 900 m, 1500 m, and 2000 m) with three difference stack height i.e. 0 m, 40 m and 100 m. The result of the whole dose calculation is under permitted criteria for whole dose : 0.25 Sv and thyroid dose : 3.0 Sv. The calculation of radiation dose in this paper use EEDCDQ code

  13. Follow-up Designs to Resolve Confounding in Split-Plot Experiments

    DEFF Research Database (Denmark)

    Almimi, Ashraf A.; Kulahci, Murat; Montgomery, Douglas C.

    2008-01-01

    Split-plot designs are effective in industry due to time and/or cost constraints, restriction on randomization of the treatment combinations of the hard-to-change factors, and different sizes of experimental units. Some of the results of fractional factorial split-plot experiments can be ambiguous......-alias certain effects. Six rules are provided to develop foldovers for minimum aberration resolution III and resolution IV fractional factorial split-plot designs....

  14. Mathematical modeling of a V-stack piezoelectric aileron actuation

    Directory of Open Access Journals (Sweden)

    Ioan URSU

    2016-12-01

    Full Text Available The article presents a mathematical modeling of aileron actuation that uses piezo V-shaped stacks. The aim of the actuation is the increasing of flutter speed in the context of a control law, in order to widen the flight envelope. In this way the main advantage of such a piezo actuator, the bandwidth is exploited. The mathematical model is obtained based on free body diagrams, and the numerical simulations allow a preliminary sizing of the actuator.

  15. Basic design parameters for the new PRR-1 stack

    International Nuclear Information System (INIS)

    Leopando, L.S.

    1994-01-01

    This report presents the results of work done to establish the basic design parameters of the new stack of the Philippine Research Reactor-1 (PRR-1). The work was undertaken to assure that the radioactive air emissions of the PRR-1, under both accident and normal operating conditions, will comply with modern safety practices. The work was done during June and July 1994. (author). 6 refs., 13 figs., 13 tabs

  16. Review of the stack discharge active particle contamination problem

    Energy Technology Data Exchange (ETDEWEB)

    Parker, H M

    1948-03-22

    Quantities of the order of ten million to 100 million radioactive particles per month were emitted from the stacks over a period of several months. High activity in the range 0.1 to 3..mu..c was probably confined to large carrier particles of corrosion debris from iron ductwork in the separations plant ventilation air system. This report discusses chemical, physical and radiochemical properties of the particles, and possible biological and health effects of exposure to them. (ACR)

  17. Cutting Forces Prediction in the Dry Slotting of Aluminium Stacks

    OpenAIRE

    SALGUERO, Jorge; CALAMAZ, Madalina; BATISTA, Moises; GIROT, Franck; MARCOS, Mariano

    2014-01-01

    International audience; Cutting forces are one of the inherent phenomena and a very significant indicator of themetal cutting process. The work presented in this paper is an investigation of the prediction of these parameters in slotting processes of UNS A92024-T3 (Al-Cu) stacks. So, cutting speed (V) and feed per tooth (fz) based parametric models, for experimental components of cutting force, F(fz,V) have been proposed. These models have been developed from the individual models extracted f...

  18. Availability Analysis of the Ventilation Stack CAM Interlock System

    CERN Document Server

    Young, J

    2000-01-01

    Ventilation Stack Continuous Air Monitor (CAM) Interlock System failure modes, failure frequencies, and system availability have been evaluated for the RPP. The evaluation concludes that CAM availability is as high as assumed in the safety analysis and that the current routine system surveillance is adequate to maintain this availability credited in the safety analysis, nor is such an arrangement predicted to significantly improve system availability.

  19. Structure of a stacked anthraquinone–DNA complex

    Science.gov (United States)

    De Luchi, Daniela; Usón, Isabel; Wright, Glenford; Gouyette, Catherine; Subirana, Juan A.

    2010-01-01

    The crystal structure of the telomeric sequence d(UBrAGG) interacting with an anthraquinone derivative has been solved by MAD. In all previously studied complexes of intercalating drugs, the drug is usually sandwiched between two DNA base pairs. Instead, the present structure looks like a crystal of stacked anthraquinone molecules in which isolated base pairs are intercalated. Unusual base pairs are present in the structure, such as G·G and A·UBr reverse Watson–Crick base pairs. PMID:20823516

  20. Consolidity: Stack-based systems change pathway theory elaborated

    OpenAIRE

    Dorrah, Hassen Taher

    2014-01-01

    This paper presents an elaborated analysis for investigating the stack-based layering processes during the systems change pathway. The system change pathway is defined as the path resulting from the combinations of all successive changes induced on the system when subjected to varying environments, activities, events, or any excessive internal or external influences and happenings “on and above” its normal stands, situations or set-points during its course of life. The analysis is essentially...

  1. Numerical simulations of flux flow in stacked Josephson junctions

    DEFF Research Database (Denmark)

    Madsen, Søren Peder; Pedersen, Niels Falsig

    2005-01-01

    We numerically investigate Josephson vortex flux flow states in stacked Josephson junctions, motivated by recent experiments trying to observe the vortices in a square vortex lattice when a magnetic field is applied to layered high-Tc superconductors of the Bi2Sr2CaCu2Ox type. By extensive...... numerical simulations, we are able to clearly distinguish between triangular and square vortex lattices and to identify the parameters leading to an in-phase vortex configuration....

  2. High Temperature PEM Fuel Cell Stacks with Advent TPS Meas

    Directory of Open Access Journals (Sweden)

    Neophytides Stylianos

    2017-01-01

    Full Text Available High power/high energy applications are expected to greatly benefit from high temperature Polymer Electrolyte Membrane Fuel Cells (PEMFCs. In this work, a combinatorial approach is presented, in which separately developed and evaluated MEAs, design and engineering are employed to result in reliable and effective stacks operating above 180°C and having the characteristics well matched to applications including auxiliary power, micro combined heat and power, and telecommunication satellites.

  3. Parametric Sensitivity Tests- European PEM Fuel Cell Stack Test Procedures

    DEFF Research Database (Denmark)

    Araya, Samuel Simon; Andreasen, Søren Juhl; Kær, Søren Knudsen

    2014-01-01

    performed based on test procedures proposed by a European project, Stack-Test. The sensitivity of a Nafion-based low temperature PEMFC stack’s performance to parametric changes was the main objective of the tests. Four crucial parameters for fuel cell operation were chosen; relative humidity, temperature......, pressure, and stoichiometry at varying current density. Furthermore, procedures for polarization curve recording were also tested both in ascending and descending current directions....

  4. Nature and magnitude of aromatic stacking of nucleic acid bases

    Czech Academy of Sciences Publication Activity Database

    Šponer, Jiří; Riley, K.E.; Hobza, Pavel

    2008-01-01

    Roč. 10, č. 19 (2008), s. 2595-2610 ISSN 1463-9076 R&D Projects: GA AV ČR(CZ) IAA400550510 Institutional research plan: CEZ:AV0Z50040507; CEZ:AV0Z50040702; CEZ:AV0Z40550506 Keywords : quantum chemical calculations * base-stacking * DNA Subject RIV: BO - Biophysics Impact factor: 4.064, year: 2008

  5. Simulation Of Networking Protocols On Software Emulated Network Stack

    Directory of Open Access Journals (Sweden)

    Hrushikesh Nimkar

    2015-08-01

    Full Text Available With the increasing number and complexity of network based applications the need to easy configuration development and integration of network applications has taken a high precedence. Trivial activities such as configuration can be carried out efficiently if network services are software based rather than hardware based. Project aims at enabling the network engineers to easily include network functionalities into hisher configuration and define hisher own network stack without using the kernel network stack. Having thought of this we have implemented two functionalities UPNP and MDNS. The multicast Domain Name System MDNS resolves host names to IP addresses within small ad-hoc networks and without having need of special DNS server and its configuration. MDNS application provides every host with functionality to register itself to the router make a multicast DNS request and its resolution. To make adding network devices and networked programs to a network as easy as it is to plug in a piece of hardware into a PC we make use of UPnP. The devices and programs find out about the network setup and other networked devices and programs through discovery and advertisements of services and configure themselves accordingly. UPNP application provides every host with functionality of discovering services of other hosts and serving requests on demand. To implement these applications we have used snabbswitch framework which an open source virtualized ethernet networking stack.

  6. Stacking-Based Visualization of Trajectory Attribute Data.

    Science.gov (United States)

    Tominski, C; Schumann, H; Andrienko, G; Andrienko, N

    2012-12-01

    Visualizing trajectory attribute data is challenging because it involves showing the trajectories in their spatio-temporal context as well as the attribute values associated with the individual points of trajectories. Previous work on trajectory visualization addresses selected aspects of this problem, but not all of them. We present a novel approach to visualizing trajectory attribute data. Our solution covers space, time, and attribute values. Based on an analysis of relevant visualization tasks, we designed the visualization solution around the principle of stacking trajectory bands. The core of our approach is a hybrid 2D/3D display. A 2D map serves as a reference for the spatial context, and the trajectories are visualized as stacked 3D trajectory bands along which attribute values are encoded by color. Time is integrated through appropriate ordering of bands and through a dynamic query mechanism that feeds temporally aggregated information to a circular time display. An additional 2D time graph shows temporal information in full detail by stacking 2D trajectory bands. Our solution is equipped with analytical and interactive mechanisms for selecting and ordering of trajectories, and adjusting the color mapping, as well as coordinated highlighting and dedicated 3D navigation. We demonstrate the usefulness of our novel visualization by three examples related to radiation surveillance, traffic analysis, and maritime navigation. User feedback obtained in a small experiment indicates that our hybrid 2D/3D solution can be operated quite well.

  7. Slip-stacking Dynamics and the 20 Hz Booster

    Energy Technology Data Exchange (ETDEWEB)

    Eldred, Jeffery; Zwaska, Robert

    2015-03-01

    Slip-stacking is an accumulation technique used at Fermilab since 2004 which nearly doubles the proton intensity. The Proton Improvement Plan II intensity upgrades require a reduction in slip-stacking losses by approximately a factor of 2. We study the single-particle dynamics that determine the stability of slip-stacking particles. We introduce universal area factors to calculate the available phase space area for any set of beam parameters without individual simulation. We show the particle loss as a function of time. We calculate the injection efficiency as a function of longitudinal emittance and aspect-ratio. We demonstrate that the losses from RF single particle dynamics can be reduced by a factor of 4-10 (depending on beam parameters) by upgrading the Fermilab Booster from a 15-Hz cycle-rate to a 20-Hz cycle-rate. We recommend a change in injection scheme to eliminate the need for a greater momentum aperture in the Fermilab Recycler.

  8. Calculated stacking-fault energies of elemental metals

    DEFF Research Database (Denmark)

    Rosengaard, N. M.; Skriver, Hans Lomholt

    1993-01-01

    We have performed ab initio calculations of twin, intrinsic, and extrinsic face-centered-cubic stacking faults for all the 3d, 4d, and 5d transition metals by means of a Green's-function technique, based on the linear-muffin-tin-orbitals method within the tight-binding and atomic-sphere approxima......We have performed ab initio calculations of twin, intrinsic, and extrinsic face-centered-cubic stacking faults for all the 3d, 4d, and 5d transition metals by means of a Green's-function technique, based on the linear-muffin-tin-orbitals method within the tight-binding and atomic......-sphere approximations. The results are in excellent agreement with recent layer Korringa-Kohn-Rostoker Green's-function calculations where stacking-fault energies for Ni, Cu, Rh, Pd, Ag, Ir, and Au were found by means of the the so-called force theorem. We find that the self-consistent fault energies for all the metals...... on the local atomic coordination are obeyed to a high degree of accuracy....

  9. Nuclear Magnetic Shieldings of Stacked Aromatic and Antiaromatic Molecules.

    Science.gov (United States)

    Sundholm, Dage; Rauhalahti, Markus; Özcan, Nergiz; Mera-Adasme, Raúl; Kussmann, Jörg; Luenser, Arne; Ochsenfeld, Christian

    2017-05-09

    Nuclear magnetic shieldings have been calculated at the density functional theory (DFT) level for stacks of benzene, hexadehydro[12]annulene, dodecadehydro[18]annulene, and hexabenzocoronene. The magnetic shieldings due to the ring currents in the adjacent molecules have been estimated by calculating nucleus independent molecular shieldings for the monomer in the atomic positions of neighbor molecules. The calculations show that the independent shielding model works reasonably well for the 1 H NMR shieldings of benzene and hexadehydro[12]annulene, whereas for the larger molecules and for the 13 C NMR shieldings the interaction between the molecules leads to shielding effects that are at least of the same size as the ring current contributions from the adjacent molecules. A better agreement is obtained when the nearest neighbors are also considered at full quantum mechanical (QM) level. The calculations suggest that the nearest solvent molecules must be included in the quantum mechanical system, at least when estimating solvent shifts at the molecular mechanics (MM) level. Current density calculations show that the stacking does not significantly affect the ring current strengths of the individual molecules, whereas the shape of the ring current for a single molecule differs from that of the stacked molecules.

  10. Multibands tunneling in AAA-stacked trilayer graphene

    Science.gov (United States)

    Redouani, Ilham; Jellal, Ahmed; Bahaoui, Abdelhadi; Bahlouli, Hocine

    2018-04-01

    We study the electronic transport through np and npn junctions for AAA-stacked trilayer graphene. Two kinds of gates are considered where the first is a single gate and the second is a double gate. After obtaining the solutions for the energy spectrum, we use the transfer matrix method to determine the three transmission probabilities for each individual cone τ = 0 , ± 1 . We show that the quasiparticles in AAA-stacked trilayer graphene are not only chiral but also labeled by an additional cone index τ. The obtained bands are composed of three Dirac cones that depend on the chirality indexes. We show that there is perfect transmission for normal or near normal incidence, which is a manifestation of the Klein tunneling effect. We analyze also the corresponding total conductance, which is defined as the sum of the conductance channels in each individual cone. Our results are numerically discussed and compared with those obtained for ABA- and ABC-stacked trilayer graphene.

  11. Automatic Extraction of Small Spatial Plots from Geo-Registered UAS Imagery

    Science.gov (United States)

    Cherkauer, Keith; Hearst, Anthony

    2015-04-01

    Accurate extraction of spatial plots from high-resolution imagery acquired by Unmanned Aircraft Systems (UAS), is a prerequisite for accurate assessment of experimental plots in many geoscience fields. If the imagery is correctly geo-registered, then it may be possible to accurately extract plots from the imagery based on their map coordinates. To test this approach, a UAS was used to acquire visual imagery of 5 ha of soybean fields containing 6.0 m2 plots in a complex planting scheme. Sixteen artificial targets were setup in the fields before flights and different spatial configurations of 0 to 6 targets were used as Ground Control Points (GCPs) for geo-registration, resulting in a total of 175 geo-registered image mosaics with a broad range of geo-registration accuracies. Geo-registration accuracy was quantified based on the horizontal Root Mean Squared Error (RMSE) of targets used as checkpoints. Twenty test plots were extracted from the geo-registered imagery. Plot extraction accuracy was quantified based on the percentage of the desired plot area that was extracted. It was found that using 4 GCPs along the perimeter of the field minimized the horizontal RMSE and enabled a plot extraction accuracy of at least 70%, with a mean plot extraction accuracy of 92%. The methods developed are suitable for work in many fields where replicates across time and space are necessary to quantify variability.

  12. Immigration of the barley mildew pathogen into field plots of barley

    DEFF Research Database (Denmark)

    O'Hara, R.B.; Brown, J.K.M.

    1996-01-01

    Immigration of the barley powdery mildew pathogen (Erysiphe graminis f.sp. hordei) into field plots of the spring barley variety Tyra (carrying the resistance allele Mla1) was investigated. Spores were trapped from the top of the plot canopies, as well as from control plots of wheat with no barley...... nearby. Comparison of the frequencies of virulent and avirulent single-colony isolates showed that the amount of immigration, relative to the amount of inoculum being produced within the plot, reduced very rapidly, until it could not be detected in the middle of the growing season (mid-June)....

  13. Estimation of Missing Observations in Two-Level Split-Plot Designs

    DEFF Research Database (Denmark)

    Almimi, Ashraf A.; Kulahci, Murat; Montgomery, Douglas C.

    2008-01-01

    Inserting estimates for the missing observations from split-plot designs restores their balanced or orthogonal structure and alleviates the difficulties in the statistical analysis. In this article, we extend a method due to Draper and Stoneman to estimate the missing observations from unreplicated...... to the number of the missing observations. These estimates are inserted into the design table and the estimates for the remaining effects (or alias chains of effects as the case with FFSP designs) are plotted on two half-normal plots: one for the whole-plot effects and the other for the subplot effects...

  14. Description of plotting program for measurements of helium flow from metal tritides

    International Nuclear Information System (INIS)

    Beavis, L.C.

    1978-09-01

    The computer program used to reduce and plot data taken from measurements of the 3 He flow from various tritides is described. The data required are taken from the appropriate files, reduced if required, and stored in two temporary arrays. Data may be edited, if desired, to remove spurious values. The temporary arrays are used in the plot subroutine as X, Y pairs. Either can be independently plotted linearly, logarithmically, or hyperbolically. Scale factors are either determined from the range of data to be plotted or by the user of the program

  15. Comparison of strain fields in truncated and un-truncated quantum dots in stacked InAs/GaAs nanostructures with varying stacking periods

    CERN Document Server

    Shin, H; Yoo, Y H

    2003-01-01

    Strain fields in truncated and un-truncated InAs quantum dots with the same height and base length have been compared numerically when the dots are vertically stacked in a GaAs matrix at various stacking periods. The compressive hydrostatic strain in truncated dots decreases slightly as compared with the un-truncated dots without regard to the stacking period studied. However, the reduction in tensile biaxial strain, compressive radial strain and tensile axial strain was salient in the truncated dot and the reduction increased with decreasing stacking period. From such changes in strain, changes in the band gap and related properties are anticipated.

  16. Identification of critical parameters for PEMFC stack performance characterization and control strategies for reliable and comparable stack benchmarking

    DEFF Research Database (Denmark)

    Mitzel, Jens; Gülzow, Erich; Kabza, Alexander

    2016-01-01

    This paper is focused on the identification of critical parameters and on the development of reliable methodologies to achieve comparable benchmark results. Possibilities for control sensor positioning and for parameter variation in sensitivity tests are discussed and recommended options for the ......This paper is focused on the identification of critical parameters and on the development of reliable methodologies to achieve comparable benchmark results. Possibilities for control sensor positioning and for parameter variation in sensitivity tests are discussed and recommended options...... in an average cell voltage deviation of 21 mV. Test parameters simulating different stack applications are summarized. The stack demonstrated comparable average cell voltage of 0.63 V for stationary and portable conditions. For automotive conditions, the voltage increased to 0.69 V, mainly caused by higher...

  17. Measurements of the LHCb software stack on the ARM architecture

    International Nuclear Information System (INIS)

    Kartik, S Vijay; Couturier, Ben; Clemencic, Marco; Neufeld, Niko

    2014-01-01

    The ARM architecture is a power-efficient design that is used in most processors in mobile devices all around the world today since they provide reasonable compute performance per watt. The current LHCb software stack is designed (and thus expected) to build and run on machines with the x86/x86 6 4 architecture. This paper outlines the process of measuring the performance of the LHCb software stack on the ARM architecture – specifically, the ARMv7 architecture on Cortex-A9 processors from NVIDIA and on full-fledged ARM servers with chipsets from Calxeda – and makes comparisons with the performance on x86 6 4 architectures on the Intel Xeon L5520/X5650 and AMD Opteron 6272. The paper emphasises the aspects of performance per core with respect to the power drawn by the compute nodes for the given performance – this ensures a fair real-world comparison with much more 'powerful' Intel/AMD processors. The comparisons of these real workloads in the context of LHCb are also complemented with the standard synthetic benchmarks HEPSPEC and Coremark. The pitfalls and solutions for the non-trivial task of porting the source code to build for the ARMv7 instruction set are presented. The specific changes in the build process needed for ARM-specific portions of the software stack are described, to serve as pointers for further attempts taken up by other groups in this direction. Cases where architecture-specific tweaks at the assembler lever (both in ROOT and the LHCb software stack) were needed for a successful compile are detailed – these cases are good indicators of where/how the software stack as well as the build system can be made more portable and multi-arch friendly. The experience gained from the tasks described in this paper are intended to i) assist in making an informed choice about ARM-based server solutions as a feasible low-power alternative to the current compute nodes, and ii) revisit the software design and build system for portability and

  18. Solid Oxide Cell and Stack Testing, Safety and Quality Assurance (SOCTESQA)

    DEFF Research Database (Denmark)

    Auer, C.; Lang, M.; Couturier, K.

    2015-01-01

    In the EU-funded project “SOCTESQA” partners from Europe and Singapore are working together to develop uniform and industry wide test procedures and protocols for solid oxide cells and stacks SOC cell/stack assembly. New application fields which are based on the operation of the SOC cell/stack as......In the EU-funded project “SOCTESQA” partners from Europe and Singapore are working together to develop uniform and industry wide test procedures and protocols for solid oxide cells and stacks SOC cell/stack assembly. New application fields which are based on the operation of the SOC cell...

  19. LAB3 Cosmic Ray Test Stand Analysis of Steel Stack Supports

    International Nuclear Information System (INIS)

    Cease, H.

    1998-01-01

    A cosmic ray test stand is being constructed at Lab 3. The stand consists of two stacks of steel plates one resting on top of the other. The top stack is composed of 6 plates of steel making an overall stack size of 34.5-inch x 40-inch x 99-inch. The bottom stack also has 6 layers of plate making an overall size of approximately 49.5-inch x 82-inch x 99-inch. The bottom stack is supported with three support legs. See drawing 3823.000ME-900428 for the individual plate orientation. The minimum support leg size and necessary welds between plates are determined.

  20. Dose assessment for potential radionuclide emissions from stacks on the Hanford Site: NESHAP compliance

    International Nuclear Information System (INIS)

    Davis, W.E.; Barnett, J.M.; Kenoyer, J.L.

    1994-03-01

    The purpose of this document is to present the assessment results for the registered stacks on the Hanford Site for potential emissions, i.e. emissions with no control devices in place. Further, the document will identify those stacks requiring continuous monitoring, i.e. the effective dose equivalent from potential emissions >0.1 mrem/yr. The stack assessment of potential emissions was performed on 84 registered stacks on the Hanford Site. These emission sources represent individual point sources presently registered under Washington Administrative code 246-247 with the Washington Department of Health. The methods used in assessing the potential emissions from the stacks are described