Radial oil injection applied to main engine bearings: evaluation of injection control rules

DEFF Research Database (Denmark)

Estupiñan, EA; Santos, Ilmar

2012-01-01

, the dynamic behaviour of the main bearing of a medium-size engine is theoretically analysed when the engine operates with controllable radial oil injection and four different injection control rules. The theoretical investigation is based on a single-cylinder combustion engine model. The performance......The performance of main bearings in a combustion engine affects key functions such as durability, noise and vibration. Thus, with the aim of reducing friction losses and vibrations between the crankshaft and the bearings, the work reported here evaluates different strategies for applying...... controllable radial oil injection to main crankshaft journal bearings. In an actively lubricated bearing, conventional hydrodynamic lubrication is combined with controllable hydrostatic lubrication, where the oil injection pressures can be modified depending on the operational conditions. In this study...

Applying CFD in the Analysis of Heavy Oil/Water Separation Process via Hydrocyclone

Directory of Open Access Journals (Sweden)

K Angelim

2017-06-01

Full Text Available In recent years most of the oil reserves discovered has been related to heavy oil reservoirs whose reserves are abundant but still show operational difficulties. This fact provoked great interest of the petroleum companies in developing new technologies for increasing the heavy oil production. Produced water generation, effluent recovered from the production wells together with oil and natural gas, is among the greatest potential factors for environmental degradation. Thus, a new scenario of the oil industry appears requiring improvement in treatment units for produced water. Among the technological improvements in the facilities, the use of hydrocyclones has been applied in the treatment of the oily water. In this sense, this study aims to investigate numerically the separation process of heavy oil from a water stream via hydrocyclone, using the computational fluid dynamics technique. In the mathematical modeling was considered a two-phase, three-dimensional, stationary, isothermal and turbulent flow. Results of streamlines, pressure and volume fraction fields of the involved phases (oil and water into the hydrocyclone, and mechanical efficiency and pumping power of the fluids are shown and analyzed. In conclusion, it seems that with increasing fluid input velocity in the device there is an increase in pressure drop, indicating a greater pumping energy consumption of the mixture, and greatly influences the separation process efficiency.

Effect of vegetable oils applied over acquired enamel pellicle on initial erosion

Directory of Open Access Journals (Sweden)

Franciny Querobim IONTA

Full Text Available Abstract Objective The prevalence of dental erosion has been recently increasing, requiring new preventive and therapeutic approaches. Vegetable oils have been studied in preventive dentistry because they come from a natural, edible, low-cost, and worldwide accessible source. This study aimed to evaluate the protective effect of different vegetable oils, applied in two concentrations, on initial enamel erosion. Material and Methods Initially, the acquired pellicle was formed in situ for 2 hours. Subsequently, the enamel blocks were treated in vitro according to the study group (n=12/per group: GP5 and GP100 – 5% and pure palm oil, respectively; GC5 and GC100 – 5% and pure coconut oil; GSa5 and GSa100 – 5% and pure safflower oil; GSu5 and GSu100 – 5% and pure sunflower oil; GO5 and GO100 – 5% and pure olive oil; CON− – Deionized Water (negative control and CON+ – Commercial Mouthwash (Elmex® Erosion Protection Dental Rinse, GABA/positive control. Then, the enamel blocks were immersed in artificial saliva for 2 minutes and subjected to short-term acid exposure in 0.5% citric acid, pH 2.4, for 30 seconds, to promote enamel surface softening. The response variable was the percentage of surface hardness loss [((SHi - SHf / SHf ×100]. Data were analyzed by one-way ANOVA and Tukey’s test (p0.05 and less than the other groups (p<0.05. There was no difference between GP5, GC5, GC100, GSa5, GSu100, GSa100, GSu5, GO5, GO100, CON− and CON+. Conclusion Palm oil seems to be a promising alternative for preventing enamel erosion. However, further studies are necessary to evaluate a long-term erosive cycling.

Effect of vegetable oils applied over acquired enamel pellicle on initial erosion

Science.gov (United States)

IONTA, Franciny Querobim; de ALENCAR, Catarina Ribeiro Barros; VAL, Poliana Pacifico; BOTEON, Ana Paula; JORDÃO, Maisa Camillo; HONÓRIO, Heitor Marques; BUZALAF, Marília Afonso Rabelo; RIOS, Daniela

2017-01-01

Abstract Objective The prevalence of dental erosion has been recently increasing, requiring new preventive and therapeutic approaches. Vegetable oils have been studied in preventive dentistry because they come from a natural, edible, low-cost, and worldwide accessible source. This study aimed to evaluate the protective effect of different vegetable oils, applied in two concentrations, on initial enamel erosion. Material and Methods Initially, the acquired pellicle was formed in situ for 2 hours. Subsequently, the enamel blocks were treated in vitro according to the study group (n=12/per group): GP5 and GP100 – 5% and pure palm oil, respectively; GC5 and GC100 – 5% and pure coconut oil; GSa5 and GSa100 – 5% and pure safflower oil; GSu5 and GSu100 – 5% and pure sunflower oil; GO5 and GO100 – 5% and pure olive oil; CON− – Deionized Water (negative control) and CON+ – Commercial Mouthwash (Elmex® Erosion Protection Dental Rinse, GABA/positive control). Then, the enamel blocks were immersed in artificial saliva for 2 minutes and subjected to short-term acid exposure in 0.5% citric acid, pH 2.4, for 30 seconds, to promote enamel surface softening. The response variable was the percentage of surface hardness loss [((SHi - SHf) / SHf )×100]. Data were analyzed by one-way ANOVA and Tukey’s test (p0.05) and less than the other groups (p<0.05). There was no difference between GP5, GC5, GC100, GSa5, GSu100, GSa100, GSu5, GO5, GO100, CON− and CON+. Conclusion Palm oil seems to be a promising alternative for preventing enamel erosion. However, further studies are necessary to evaluate a long-term erosive cycling. PMID:28877281

Alkaline polymer electrolyte fuel cells stably working at 80 °C

Science.gov (United States)

Peng, Hanqing; Li, Qihao; Hu, Meixue; Xiao, Li; Lu, Juntao; Zhuang, Lin

2018-06-01

Alkaline polymer electrolyte fuel cells are a new class of polymer electrolyte fuel cells that fundamentally enables the use of nonprecious metal catalysts. The cell performance mostly relies on the quality of alkaline polymer electrolytes, including the ionic conductivity and the chemical/mechanical stability. For a long time, alkaline polymer electrolytes are thought to be too weak in stability to allow the fuel cell to be operated at elevated temperatures, e.g., above 60 °C. In the present work, we report a progress in the state-of-the-art alkaline polymer electrolyte fuel cell technology. By using a newly developed alkaline polymer electrolyte, quaternary ammonia poly (N-methyl-piperidine-co-p-terphenyl), which simultaneously possesses high ionic conductivity and excellent chemical/mechanical stability, the fuel cell can now be stably operated at 80 °C with high power density. The peak power density reaches ca. 1.5 W/cm2 at 80 °C with Pt/C catalysts used in both the anode and the cathode. The cell works stably in a period of study over 100 h.

TOL plasmid transfer during bacterial conjugation in vitro and rhizoremediation of oil compounds in vivo

International Nuclear Information System (INIS)

Jussila, Minna M.; Zhao, Ji; Suominen, Leena; Lindstroem, Kristina

2007-01-01

Molecular profiling methods for horizontal transfer of aromatics-degrading plasmids were developed and applied during rhizoremediation in vivo and conjugations in vitro. pWW0 was conjugated from Pseudomonas to Rhizobium. The xylE gene was detected both in Rhizobium galegae bv. officinalis and bv. orientalis, but it was neither stably maintained in orientalis nor functional in officinalis. TOL plasmids were a major group of catabolic plasmids among the bacterial strains isolated from the oil-contaminated rhizosphere of Galega orientalis. A new finding was that some Pseudomonas migulae and Pseudomonas oryzihabitans strains harbored a TOL plasmid with both pWW0- and pDK1-type xylE gene. P. oryzihabitans 29 had received the archetypal TOL plasmid pWW0 from Pseudomonas putida PaW85. As an application for environmental biotechnology, the biodegradation potential of oil-polluted soil and the success of bioremediation could be estimated by monitoring changes not only in the type and amount but also in transfer of degradation plasmids. - Horizontal transfer of degradation plasmids in the oil-contaminated rhizosphere reveals the dynamic nature of the intrinsic biodegradation potential

Oyster polynuclear aromatic hydrocarbon fingerprinting applied to the Apex barge oil spill

International Nuclear Information System (INIS)

Wade, T.L.; Jackson, T.J.; McDonald, T.J.; Sericano, J.L.; Brooks, J.M.

1993-01-01

An estimated 692,000 gallons of catalytic feed stock oil was spilled into Galveston Bay on July 28, 1990, when a tanker collided with three Apex barges in the Houston Ship Channel. Oysters were collected and analyzed from Galveston Bay Todd's Dump (GBRD) before the spill and after the spill. Oysters were also collected from Galveston Bay Redfish Island (GBRI), a site known to be impacted by the spill, 37 and 110 days after the spill. The spilled oil was also analyzed. The concentration of 18 polynuclear aromatic hydrocarbons (PAH) measured as part of the National Oceanic and Atmospheric Administration's National Status ampersand Trends (NS ampersand T) showed a sharp increase from 100 ng/g to over 600 ng/g. Concentrations of these 18 PAHs were also found at GBRI. Fingerprinting techniques applied to data from oyster analyses demonstrated the presence of bioavailable Apex Barge oil 37, 110, and 132 days after the spill at GHTD and GBRI. Fingerprinting becomes less diagnostic with time due to possible environmental weathering of the oil. The fingerprint from GBTD 495 and 851 days after the spill will be presented and discussed

Scaffold-free 3D bio-printed human liver tissue stably maintains metabolic functions useful for drug discovery.

Science.gov (United States)

Kizawa, Hideki; Nagao, Eri; Shimamura, Mitsuru; Zhang, Guangyuan; Torii, Hitoshi

2017-07-01

The liver plays a central role in metabolism. Although many studies have described in vitro liver models for drug discovery, to date, no model has been described that can stably maintain liver function. Here, we used a unique, scaffold-free 3D bio-printing technology to construct a small portion of liver tissue that could stably maintain drug, glucose, and lipid metabolism, in addition to bile acid secretion. This bio-printed normal human liver tissue maintained expression of several kinds of hepatic drug transporters and metabolic enzymes that functioned for several weeks. The bio-printed liver tissue displayed glucose production via cAMP/protein kinase A signaling, which could be suppressed with insulin. Bile acid secretion was also observed from the printed liver tissue, and it accumulated in the culture medium over time. We observed both bile duct and sinusoid-like structures in the bio-printed liver tissue, which suggested that bile acid secretion occurred via a sinusoid-hepatocyte-bile duct route. These results demonstrated that our bio-printed liver tissue was unique, because it exerted diverse liver metabolic functions for several weeks. In future, we expect our bio-printed liver tissue to be applied to developing new models that can be used to improve preclinical predictions of long-term toxicity in humans, generate novel targets for metabolic liver disease, and evaluate biliary excretion in drug development.

Tariff Policy Applied in the Adriatic Oil Pipeline

International Nuclear Information System (INIS)

Skodlar, Z.; Poljak, J.

1995-01-01

The policy of energy costs of crude oil transportation by pipeline strongly encourages an operational regime which results in poor pump efficiency. Oil is being unnecessarily and for too long time retained in oil storage tanks, thus increasing evaporation losses. (author). 3 figs., 2 tabs

A Three-Dimensional Foil Bearing Performance Map Applied to Oil-Free Turbomachinery

Science.gov (United States)

2009-04-01

stress brought on by excessive viscous power loss; therefore a map that graphically relates component and system-level parameters (bearing size, applied...Introduction Foil bearings are self-acting, hydrodynamic gas bearings that use air as their working fluid . Their use in rotating systems eliminates the...weight, maintenance requirements, speed, and temperature limitations associated with conventional oil-lubricated rotor supports (i.e., bearings, dampers

Oil-Impregnated Polyethylene Films

Science.gov (United States)

Mukherjee, Ranit; Habibi, Mohammad; Rashed, Ziad; Berbert, Otacilio; Shi, Shawn; Boreyko, Jonathan

2017-11-01

Slippery liquid-infused porous surfaces (SLIPS) minimize the contact angle hysteresis of a wide range of liquids and aqueous food products. Although hydrophobic polymers are often used as the porous substrate for SLIPS, the choice of polymer has been limited to silicone-based or fluorine-based materials. Hydrocarbon-based polymers, such as polyethylene, are cost effective and widely used in food packaging applications where SLIPS would be highly desirable. However, to date there have been no reports on using polyethylene as a SLIPS substrate, as it is considered highly impermeable. Here, we show that thin films of low-density polyethylene can be stably impregnated with carbon-based oils without requiring any surface modification. Wicking tests reveal that oils with sufficient chemical compatibility follow Washburn's equation. The nanometric effective pore size of the polyethylene does result in a very low wicking speed, but by using micro-thin films and a drawdown coater, impregnation can still be completed in under one second. The oil-impregnated polyethylene films promoted ultra-slippery behavior for water, ketchup, and yogurt while remaining durable even after being submerged in ketchup for over one month. This work was supported by Bemis North America (AT-23981).

Effect of applied DC voltages and temperatures on space charge behaviour of multi-layer oil-paper insulation

Energy Technology Data Exchange (ETDEWEB)

Tang Chao; Liao Ruijin [The State Key Laboratory of Power Transmission Equipment and System Security and New Technology, Chongqing University (China); Chen, G [School of Electronics and Computer Science, University of Southampton (United Kingdom); Fu, M, E-mail: tangchao_1981@163.co [AVERA T and D Technology Centre, Stafford (United Kingdom)

2009-08-01

In this paper, space charge in a multi-layer oil-paper insulation system was investigated using the pulsed electroacoustic (PEA) technique. A series of measurements had been carried following subjection of the insulation system to different applied voltages and different temperatures. Charge behaviours in the insulation system were analyzed and the influence of temperature on charge dynamics was discussed. The test results shows that homocharge injection takes place under all the test conditions, the applied DC voltage mainly affects the amount of space charge, while the temperature has greater influence on the distribution and mobility of space charge inside oil-paper samples.

Characterization of a Madin-Darby canine kidney cell line stably expressing TRPV5.

NARCIS (Netherlands)

Dekker, E. den; Schoeber, J.P.H.; Topala, C.N.; Graaf, S.F.J. van de; Hoenderop, J.G.J.; Bindels, R.J.M.

2005-01-01

To provide a cell model for studying specifically the regulation of Ca2+ entry by the epithelial calcium channel transient receptor potential-vanilloid-5 (TRPV5), green fluorescent protein (GFP)-tagged TRPV5 was expressed stably in Madin-Darby canine kidney type I (MDCK) cells. The localization of

Applying CFD in the Analysis of Heavy-Oil Transportation in Curved Pipes Using Core-Flow Technique

Directory of Open Access Journals (Sweden)

S Conceição

2017-06-01

Full Text Available Multiphase flow of oil, gas and water occurs in the petroleum industry from the reservoir to the processing units. The occurrence of heavy oils in the world is increasing significantly and points to the need for greater investment in the reservoirs exploitation and, consequently, to the development of new technologies for the production and transport of this oil. Therefore, it is interesting improve techniques to ensure an increase in energy efficiency in the transport of this oil. The core-flow technique is one of the most advantageous methods of lifting and transporting of oil. The core-flow technique does not alter the oil viscosity, but change the flow pattern and thus, reducing friction during heavy oil transportation. This flow pattern is characterized by a fine water pellicle that is formed close to the inner wall of the pipe, aging as lubricant of the oil flowing in the core of the pipe. In this sense, the objective of this paper is to study the isothermal flow of heavy oil in curved pipelines, employing the core-flow technique. A three-dimensional, transient and isothermal mathematical model that considers the mixture and k-e  turbulence models to address the gas-water-heavy oil three-phase flow in the pipe was applied for analysis. Simulations with different flow patterns of the involved phases (oil-gas-water have been done, in order to optimize the transport of heavy oils. Results of pressure and volumetric fraction distribution of the involved phases are presented and analyzed. It was verified that the oil core lubricated by a fine water layer flowing in the pipe considerably decreases pressure drop.

Method of stably radiolabeling antibodies with technetium and rhenium

International Nuclear Information System (INIS)

Paik, C.H.; Reba, R.C.; Eckelman, W.C.

1987-01-01

A method is described for labeling antibodies or antibody fragments with radionuclides of technetium or rhenium to obtain stable labeling, comprising: reacting a reduced radioisotope of technetium or rhenium with an antibody or antibody fragment, or a diethylenetriaminepentaacetic acid conjugated antibody or antibody fragment, in the presence of free or carrier-bound diethylenetriaminepentaacetic acid (DTPA). The amount of DTPA is sufficient to substantially completely inhibit binding of the reduced technetium or rhenium to nonstable binding sites of the antibody or antibody fragment, or the DTPA-conjugated antibody or antibody fragment. The resultant stably labeled antibody or antibody fragment, or DTPA[conjugated antibody or antibody fragment is recovered

Proceedings of the 3. international symposium on applied microbiology and molecular biology in oil systems: ISMOS 3

Energy Technology Data Exchange (ETDEWEB)

Rooijen, Gijs van; Caffrey, Sean M. [Genome Alberta (Canada); Lund Skovhus, Torben [DTI Oil and Gas (Denmark); Whitby, Corinne [University of Essex (United Kingdom)

2011-07-01

The 3rd international symposium on applied microbiology and molecular biology in oil systems was held in Calgary, Alberta, Canada, from June 13th to June 15th, 2011. This conference, organized by ISMOS TSC, gathered experts to discuss the application of microbial and molecular biology in the hydrocarbon sector. The conference was attended by key players from the oil and gas industry and provided them with the opportunity to learn about some of the latest technologies in areas such as the application of molecular microbiological methods for oil field systems, biodegradation of hydrocarbons in oil production, biofuels and downstream petroleum microbiology and challenges in biofuels and oil sands developments, and to network with their peers and share their expertise. 17 of the 31 papers presented during this conference have been catalogued separately for inclusion in this database.

Oil risk in oil stocks

NARCIS (Netherlands)

Scholtens, Bert; Wang, L

2008-01-01

We assess the oil price sensitivities and oil risk premiums of NYSE listed oil & gas firms' returns by using a two-step regression analysis under two different arbitrage pricing models. Thus, we apply the Fama and French (1992) factor returns in a study of oil stocks. In all, we find that the return

Characterization of new cell line stably expressing CHI3L1 oncogene

Directory of Open Access Journals (Sweden)

Chekhonin V. P.

2011-06-01

Full Text Available Aim. To characterize the immortalized 293 cell line after stable transfection with human oncogene (CHI3L1. Methods. 293 cells, stably transfected with pcDNA3.1_CHI3L1, and 293 cells, stably transfected with pcDNA3.1 as a negative control, were used throughout all experiments. The clones of CHI3L1-expressing 293 cells and 293 cells, transfected with pcDNA3.1, were analyzed by immunofluorescence and confocal microscopy. Cell proliferation was measured using MTT assay; analyses of ERK1/2 and AKT activation and their cellular localization were performed with anti-phospho-ERK and anti-phospho-AKT antibodies. Specific activation of MAP and PI3 kinases was measured by densitometric analysis of Western-blot signals. Results. The obtained results show quite modest ability of CHI3L1 to stimulate cell growth and reflect rather an improved cellular plating efficiency of the 293 cells stably transfected with pcDNA3.1_CHI3L1 as compared to the 293 cells transfected with an «empty» vector. ERK1/2 and AKT are activated in the 293_CHI3L1 cells. In these cells phosphorylated ERK1/2 were localized in both cell cytoplasm and nuclei while AKT only in cytoplasm. The 293_CHI3L1 cells differed from the 293 cells, transfected with an «empty» vector, in their size and ability to adhere to the culture plates. Conclusions. The overexpression of CHI3L1 is likely to have an important role in tumorigenesis via a mechanism which involves activation of PI3K and ERK1/2 pathways. The tumors which can be induced by orthotopic implantation of the transformed human cells with overexpressed human oncogene CHI3L1 into the rat brain can be used as a target for anticancer drug development.

Hazard identification studies applied to oil pipelines

Energy Technology Data Exchange (ETDEWEB)

Savio, Augusto; Alpert, Melina L. [TECNA S.A., Buenos Aires (Argentina)], e-mail: asavio@tecna.com, e-mail: malpert@tecna.com

2008-07-01

In order to assess risks inherent to an Oil Pipeline, it is imperative to analyze what happens 'outside the process'. HAZID (HAZard IDentification) studies are mainly carried out for this purpose. HAZID is a formal study which identifies hazards and risks associated to an operation or facility and enable its acceptability assessment. It is a brainstorming exercise guided by a typical 'Checklist', divided into four Sections: External, Facilities and Health Hazards and Issues pertaining to Project Execution, which are further subdivided into Hazard Categories. For each Category, there are 'Guide-words' and 'Prompts'. Even if an Oil Pipeline Risk Assessment can be performed by means of the above referred 'Checklist', carrying out the actual process can become lengthy and annoying due to the lack of specificity. This work aims at presenting the most suitable 'Checklist' for the identification of Oil Pipeline Risk Assessment, although it could be used for Gas Pipeline Risk Assessment too. Prepared ad hoc, this list, is based on the spill causes established by CONCAWE (CONservation of Clean Air Water in Europe). Performing Oil Pipeline Risk Assessment by means of specially formulated Checklist enables the Study Team to easily identify risks, shortens execution time and provides both accuracy and specificity. (author)

Synergetic Use of Principal Component Analysis Applied to Normed Physicochemical Measurements and GC × GC-MS to Reveal the Stabilization Effect of Selected Essential Oils on Heated Rapeseed Oil.

Science.gov (United States)

Sghaier, Lilia; Cordella, Christophe B Y; Rutledge, Douglas N; Lefèvre, Fanny; Watiez, Mickaël; Breton, Sylvie; Sassiat, Patrick; Thiebaut, Didier; Vial, Jérôme

2017-06-01

Lipid oxidation leads to the formation of volatile compounds and very often to off-flavors. In the case of the heating of rapeseed oil, unpleasant odors, characterized as a fishy odor, are emitted. In this study, 2 different essential oils (coriander and nutmeg essential oils) were added to refined rapeseed oil as odor masking agents. The aim of this work was to determine a potential antioxidant effect of these essential oils on the thermal stability of rapeseed oil subject to heating cycles between room temperature and 180 °C. For this purpose, normed determinations of different parameters (peroxide value, anisidine value, and the content of total polar compounds, free fatty acids and tocopherols) were carried out to examine the differences between pure and degraded oil. No significant difference was observed between pure rapeseed oil and rapeseed oil with essential oils for each parameter separately. However, a stabilizing effect of the essential oils, with a higher effect for the nutmeg essential oil was highlighted by principal component analysis applied on physicochemical dataset. Moreover, the analysis of the volatile compounds performed by GC × GC showed a substantial loss of the volatile compounds of the essential oils from the first heating cycle. © 2017 Institute of Food Technologists®.

Applying the technology of hydrodynamic cavitation treatment of high-viscosity oils to increase the efficiency of transportation

Science.gov (United States)

Brand, A. E.; Vershinina, S. V.; Vengerov, A. A.; Mostovaya, N. A.

2015-10-01

The article investigates the possibility of applying hydrodynamic cavitation treatment to reduce oil viscosity in Russian pipeline transportation system and increase its performance. The result of laboratory tests and suggestions on technology application are given

Turbulent entrainment across turbulent-nonturbulent interfaces in stably stratified mixing layers

Science.gov (United States)

Watanabe, T.; Riley, J. J.; Nagata, K.

2017-10-01

The entrainment process in stably stratified mixing layers is studied in relation to the turbulent-nonturbulent interface (TNTI) using direct numerical simulations. The statistics are calculated with the interface coordinate in an Eulerian frame as well as with the Lagrangian fluid particles entrained from the nonturbulent to the turbulent regions. The characteristics of entrainment change as the buoyancy Reynolds number Reb decreases and the flow begins to layer. The baroclinic torque delays the enstrophy growth of the entrained fluids at small Reb, while this effect is less efficient for large Reb. The entrained particle movement within the TNTI layer is dominated by the small dissipative scales, and the rapid decay of the kinetic energy dissipation rate due to buoyancy causes the entrained particle movement relative to the interface location to become slower. Although the Eulerian statistics confirm that there exists turbulent fluid with strong vorticity or with large buoyancy frequency near the TNTI, the entrained fluid particles circumvent these regions by passing through the TNTI in strain-dominant regions or in regions with small buoyancy frequency. The multiparticle statistics show that once the nonturbulent fluid volumes are entrained, they are deformed into flattened shapes in the vertical direction and diffuse in the horizontal direction. When Reb is large enough for small-scale turbulence to exist, the entrained fluid is able to penetrate into the turbulent core region. Once the flow begins to layer with decreasing Reb, however, the entrained fluid volume remains near the outer edge of the turbulent region and forms a stably stratified layer without vertical overturning.

The case for using vessel-based systems to apply oil-spill dispersants

International Nuclear Information System (INIS)

Ross, S.

1998-01-01

Most emergency plans for dealing with marine oil spills include the use of chemical dispersants. This paper presents a comparison between the capabilities of aircraft-based dispersant application systems and vessel-based systems. The comparison was presented in terms of the logistics of treating offshore spills. Vessel-based systems have certain advantages in terms of their availability and cost. They have better spray control and accuracy and can dose thick slicks in one pass. However, this advantage is lost if the dispersant payload on the vessel is relatively small and the spill is located very far from the base of operations. Under certain conditions, vessel-based dispersant application systems can treat spills as quickly as aircraft-based systems. Most marine spills tend to occur in restricted waters near ports where dispersant stockpiles could be stored for ready use by vessels in the area. Development of a modern vessel-based, fire-monitor system for applying chemical dispersant onto marine oil spills was one of the recommendations emerging from the study. 32 refs., 6 tabs., 1 fig

Elevating bioavailability of curcumin via encapsulation with a novel formulation of artificial oil bodies.

Science.gov (United States)

Chang, Ming-Tsung; Tsai, Tong-Rong; Lee, Chun-Yann; Wei, Yu-Sheng; Chen, Ying-Jie; Chen, Chun-Ren; Tzen, Jason T C

2013-10-09

Utilization of curcumin has been limited due to its poor oral bioavailability. Oral bioavailability of hydrophobic compounds might be elevated via encapsulation in artificial seed oil bodies. This study aimed to improve oral bioavailability of curcumin via this encapsulation. Unfortunately, curcumin was indissoluble in various seed oils. A mixed dissolvent formula was used to dissolve curcumin, and the admixture was successfully encapsulated in artificial oil bodies stabilized by recombinant sesame caleosin. The artificial oil bodies of relatively small sizes (150 nm) were stably solidified in the forms of powder and tablet. Oral bioavailability of curcumin with or without encapsulation in artificial oil bodies was assessed in Sprague-Dawley male rats. The results showed that encapsulation of curcumin significantly elevated its bioavailability and provided the highest maximum whole blood concentration (Cmax), 37 ± 28 ng/mL, in the experimental animals 45 ± 17 min (t(max)) after oral administration. Relative bioavailability calculated on the basis of the area under the plasma concentration-time curve (AUC) was increased by 47.7 times when curcumin was encapsulated in the artificial oil bodies. This novel formulation of artificial oil bodies seems to possess great potential to encapsulate hydrophobic drugs for oral administration.

Feasibility to apply the steam assisted gravity drainage (SAGD) technique in the country's heavy crude-oil fields

International Nuclear Information System (INIS)

Rodriguez, Edwin; Orjuela, Jaime

2004-01-01

The steam assisted gravity drainage (SAGD) processes are one of the most efficient and profitable technologies for the production of heavy crude oils and oil sands. These processes involve the drilling of a couple of parallel horizontal wells, separated by a vertical distance and located near the oil field base. The upper well is used to continuously inject steam into the zone of interest, while the lower well collects all resulting fluids (oil, condensate and formation water) and takes them to the surface (Butler, 1994). This technology has been successfully implemented in countries such as Canada, Venezuela and United States, reaching recovery factors in excess of 50%. This article provides an overview of the technique's operation mechanism and the process most relevant characteristics, as well as the various categories this technology is divided into, including all its advantages and limitations. Furthermore, the article sets the oil field's minimal conditions under which the SAGD process is efficient, which conditions, as integrated to a series of mathematical models, allow to make forecasts on production, thermal efficiency (ODR) and oil to be recovered, as long as it is feasible (from a technical point of view) to apply this technique to a defined oil field. The information and concepts compiled during this research prompted the development of software, which may be used as an information, analysis and interpretation tool to predict and quantify this technology's performance. Based on the article, preliminary studies were started for the country's heavy crude-oil fields, identifying which provide the minimum conditions for the successful development of a pilot project

Redistribution of charged aluminum nanoparticles on oil droplets in water in response to applied electrical field

Energy Technology Data Exchange (ETDEWEB)

Li, Mengqi; Li, Dongqing, E-mail: dongqing@mme.uwaterloo.ca [University of Waterloo, Department of Mechanical and Mechatronics Engineering (Canada)

2016-05-15

Janus droplets with two opposite faces of different physical or chemical properties have great potentials in many fields. This paper reports a new method for making Janus droplets by covering one side of the droplet with charged nanoparticles in an externally applied DC electric field. In this paper, aluminum oxide nanoparticles on micro-sized and macro-sized oil droplets were studied. In order to control the surface area covered by the nanoparticles on the oil droplets, the effects of the concentration of nanoparticle suspension, the droplet size as well as the strength of electric field on the final accumulation area of the nanoparticles are studied.Graphical abstract.

Quantitative Evaluation of Myostatin Gene in Stably Transfected Caprine Fibroblast Cells by Anti-Myostatin shRNA.

Science.gov (United States)

Jain, Sudhir Kumar; Jain, Hemlata; Kumar, Dharmendra; Bedekar, Megha Kadam; Pandey, Akhilesh Kumar; Sarkhel, Bikash Chandra

2015-09-01

Skeletal muscle is the major component of lean tissue that is used for consumption, and myostatin is a negative regulator of skeletal muscle growth. Downregulation of this gene therefore offers a strategy for developing superior animals with enhanced muscle growth. Knockdown of myostatin was achieved by RNA interference technology. The anti-myostatin shRNA were designed and stably transfected in caprine fibroblast cells. The reduced expression of target gene was achieved and measured in clonal fibroblast cells by real-time PCR. Two single-cell clones induced significant decrease of myostatin gene expression by 73.96 and 72.66 %, respectively (P < 0.05). To ensure the appropriate growth of transfected cell, seven media were tested. The best suited media was used for transfected fibroblast cell proliferation. The findings suggest that shRNA provides a novel potential tool for gene knockdown and these stably transfected cells can be used as the donor cells for animal cloning.

A germline chromothripsis event stably segregating in 11 individuals through three generations

DEFF Research Database (Denmark)

Bertelsen, Birgitte; Nazaryan-Petersen, Lusine; Sun, Wei

2016-01-01

PURPOSE: Parentally transmitted germ-line chromothripsis (G-CTH) has been identified in only a few cases. Most of these rearrangements were stably transmitted, in an unbalanced form, from a healthy mother to her child with congenital abnormalities probably caused by de novo copy-number changes...... of the DNA damage response, may be related to G-CTH formation. CONCLUSION: G-CTH rearrangements are not always associated with abnormal phenotypes and may be misinterpreted as balanced two-way translocations, suggesting that G-CTH is an underdiagnosed phenomenon.Genet Med 18 5, 494-500....

How to evaluate the necessity of applying the floating roof tank for storing crude oil and gasoline

Energy Technology Data Exchange (ETDEWEB)

Knezevic, E

1971-01-01

A method is described for calculating differential profit from using floating roof tanks rather than fixed roof tanks. The method is based on the extensive testing by the American Petroleum Institute and applied to the Yugoslavian climatic conditions. Several diagrams are reproduced which show how to compute losses due to breathing from a tank with fixed and floating roofs for oil and refined oil products. Also shown are average daily temperatures of air in the Zagreb region, Yugoslavia, a diagram for determining temperature changes in a vertical cylindrical tank, and typical changes undergone in a gasoline tank during a 24-hr cycle.

Vegetable oil based liquid nanocomposite dielectric

Directory of Open Access Journals (Sweden)

Leon Chetty

2013-01-01

Full Text Available Physically smaller dielectric materials would improve the optimisation of space for power systems. Development of nanotechnology provides an effective way to improve the performances of insulating oils used in power system applications. In this research study, we focused on the development of nanomodified vegetable oils to be used in power transformers. Higher conduction currents were observed in virgin linseed oil than in virgin castor oil. However, for both virgin linseed and virgin castor oil, the DC conduction current increased approximately linearly with the applied DC voltage. In nanomodified linseed oil, the characteristic curve showed two distinct regions: a linear region (at lower applied voltage and a saturation region (at slightly higher voltage. Conversely, in nanomodified castor oil, the characteristic curve showed three distinct regions: a linear region (at lower applied voltage, a saturation region (at intermediate applied voltage and an exponential growth region (at higher applied voltage. The nanomodified linseed oil exhibited a better dielectric performance than the nanomodified castor oil. Overall, the addition of nanodielectrics to vegetable oils decreased the dielectric performance of the vegetable oils. The results of this study contribute to the understanding of the pre-breakdown phenomenon in liquid nanocomposite dielectrics.

Turbulent fluxes in stably stratified boundary layers

International Nuclear Information System (INIS)

L'vov, Victor S; Procaccia, Itamar; Rudenko, Oleksii

2008-01-01

We present here an extended version of an invited talk we gave at the international conference 'Turbulent Mixing and Beyond'. The dynamical and statistical description of stably stratified turbulent boundary layers with the important example of the stable atmospheric boundary layer in mind is addressed. Traditional approaches to this problem, based on the profiles of mean quantities, velocity second-order correlations and dimensional estimates of the turbulent thermal flux, run into a well-known difficulty, predicting the suppression of turbulence at a small critical value of the Richardson number, in contradiction to observations. Phenomenological attempts to overcome this problem suffer from various theoretical inconsistencies. Here, we present an approach taking into full account all the second-order statistics, which allows us to respect the conservation of total mechanical energy. The analysis culminates in an analytic solution of the profiles of all mean quantities and all second-order correlations, removing the unphysical predictions of previous theories. We propose that the approach taken here is sufficient to describe the lower parts of the atmospheric boundary layer, as long as the Richardson number does not exceed an order of unity. For much higher Richardson numbers, the physics may change qualitatively, requiring careful consideration of the potential Kelvin-Helmoholtz waves and their interaction with the vortical turbulence.

Visual operations management tools applied to the oil pipelines and terminals standardization process: the experience of TRANSPETRO

Energy Technology Data Exchange (ETDEWEB)

Almeida, Maria Fatima Ludovico de [Pontificia Universidade Catolica do Rio de Janeiro (PUC-Rio/ITUC), Rio de Janeiro, RJ (Brazil). Instituto Tecnologico; Santiago, Adilson; Ribeiro, Kassandra Senra; Arruda, Daniela Mendonca [TRANSPETRO - PETROBRAS Transporte S.A., Rio de Janeiro, RJ (Brazil)

2009-07-01

This paper describes the process by which visual operations management (VOM) tools were implemented, concerning standards and operational procedures in TRANSPETRO's Oil Pipelines and Terminals Unit. It provides: a brief literature review of visual operations management tools applied to total quality management and the standardization processes; a discussion of the assumptions from the second level of VOM (visual standards) upon which TRANSPETRO's oil pipelines and terminals business processes and operational procedures are based; and a description of the VOM implementation process involving more than 100 employees and one illustrative example of 'Quick Guides' for right-of- way management activities. Finally, it discusses the potential impacts and benefits of using VOM tools in the current practices in TRANSPETRO's Oil Pipelines and Terminals Unit, reinforcing the importance of such visual guides as vital to implement regional and corporate procedures, focusing on the main operational processes. (author)

Turbulent circulation above the surface heat source in a stably stratified environment

Science.gov (United States)

Kurbatskii, A. F.; Kurbatskaya, L. I.

2016-09-01

The results of the numerical modeling of turbulent structure of the penetrating convection above the urban heat island with a small aspect ratio in a stably stratified medium at rest are presented. The gradient diffusion representations for turbulent momentum and heat fluxes are used, which depend on three parameters — the turbulence kinetic energy, the velocity of its spectral expenditure, and the dispersion of temperature fluctuations. These parameters are found from the closed differential equations of balance in the RANS approach of turbulence description. The distributions of averaged velocity and temperature fields as well as turbulent characteristics agree well with measurement data.

Electrospray ionization mass spectrometry and partial least squares discriminant analysis applied to the quality control of olive oil.

Science.gov (United States)

Alves, Junia O; Botelho, Bruno G; Sena, Marcelo M; Augusti, Rodinei

2013-10-01

Direct infusion electrospray ionization mass spectrometry in the positive ion mode [ESI(+)-MS] is used to obtain fingerprints of aqueous-methanolic extracts of two types of olive oils, extra virgin (EV) and ordinary (OR), as well as of samples of EV olive oil adulterated by the addition of OR olive oil and other edible oils: corn (CO), sunflower (SF), soybean (SO) and canola (CA). The MS data is treated by the partial least squares discriminant analysis (PLS-DA) protocol aiming at discriminating the above-mentioned classes formed by the genuine olive oils, EV (1) and OR (2), as well as the EV adulterated samples, i.e. EV/SO (3), EV/CO (4), EV/SF (5), EV/CA (6) and EV/OR (7). The PLS-DA model employed is built with 190 and 70 samples for the training and test sets, respectively. For all classes (1-7), EV and OR olive oils as well as the adulterated samples (in a proportion varying from 0.5 to 20.0% w/w) are properly classified. The developed methodology required no ions identification and demonstrated to be fast, as each measurement lasted about 3 min including the extraction step and MS analysis, and reliable, because high sensitivities (rate of true positives) and specificities (rate of true negatives) were achieved. Finally, it can be envisaged that this approach has potential to be applied in quality control of EV olive oils. Copyright © 2013 John Wiley & Sons, Ltd.

New techniques on oil spill modelling applied in the Eastern Mediterranean sea

Science.gov (United States)

Zodiatis, George; Kokinou, Eleni; Alves, Tiago; Lardner, Robin

2016-04-01

Small or large oil spills resulting from accidents on oil and gas platforms or due to the maritime traffic comprise a major environmental threat for all marine and coastal systems, and they are responsible for huge economic losses concerning the human infrastructures and the tourism. This work aims at presenting the integration of oil-spill model, bathymetric, meteorological, oceanographic, geomorphological and geological data to assess the impact of oil spills in maritime regions such as bays, as well as in the open sea, carried out in the Eastern Mediterranean Sea within the frame of NEREIDs, MEDESS-4MS and RAOP-Med EU projects. The MEDSLIK oil spill predictions are successfully combined with bathymetric analyses, the shoreline susceptibility and hazard mapping to predict the oil slick trajectories and the extend of the coastal areas affected. Based on MEDSLIK results, oil spill spreading and dispersion scenarios are produced both for non-mitigated and mitigated oil spills. MEDSLIK model considers three response combating methods of floating oil spills: a) mechanical recovery using skimmers or similar mechanisms; b) destruction by fire, c) use of dispersants or other bio-chemical means and deployment of booms. Shoreline susceptibility map can be compiled for the study areas based on the Environmental Susceptibility Index. The ESI classification considers a range of values between 1 and 9, with level 1 (ESI 1) representing areas of low susceptibility, impermeable to oil spilt during accidents, such as linear shorelines with rocky cliffs. In contrast, ESI 9 shores are highly vulnerable, and often coincide with natural reserves and special protected areas. Additionally, hazard maps of the maritime and coastal areas, possibly exposed to the danger on an oil spill, evaluate and categorize the hazard in levels from low to very high. This is important because a) Prior to an oil spill accident, hazard and shoreline susceptibility maps are made available to design

Visual operations management tools applied to the oil pipelines and terminals standardization process: the experience of TRANSPETRO

Energy Technology Data Exchange (ETDEWEB)

Almeida, Maria Fatima Ludovico de [Pontificia Universidade Catolica do Rio de Janeiro (PUC-Rio/ITUC), Rio de Janeiro, RJ (Brazil). Instituto Tecnologico; Santiago, Adilson; Ribeiro, Kassandra Senra; Arruda, Daniela Mendonca [TRANSPETRO - PETROBRAS Transporte S.A., Rio de Janeiro, RJ (Brazil)

2009-07-01

This paper describes the process by which visual operations management (VOM) tools were implemented, concerning standards and operational procedures in TRANSPETRO's Oil Pipelines and Terminals Unit. It provides: a brief literature review of visual operations management tools applied to total quality management and the standardization processes; a discussion of the assumptions from the second level of VOM (visual standards) upon which TRANSPETRO's oil pipelines and terminals business processes and operational procedures are based; and a description of the VOM implementation process involving more than 100 employees and one illustrative example of 'Quick Guides' for right-of- way management activities. Finally, it discusses the potential impacts and benefits of using VOM tools in the current practices in TRANSPETRO's Oil Pipelines and Terminals Unit, reinforcing the importance of such visual guides as vital to implement regional and corporate procedures, focusing on the main operational processes. (author)

High current relativistic beam propagates stably in gas surrounded by nonconducting walls

International Nuclear Information System (INIS)

Clark, J.C.

1977-01-01

LLL has been studying the propagation of high current electron beams for a number of years to understand their behavior for use in a variety of experimental uses. Our latest experiments have shown that a mildly relativistic electron beam of 10 to 15 kA and a pulse width of 30 to 40 ns can propagate stably and with no net current transfer in insulating tubes filled with neutral gases. These experiments have been performed in the Magnetic Fusion Energy program where Electronics Engineering has been operating an electron beam accelerator, designing some of the diagnostics, such as laser interferometers, and performing the experiments. This article briefly describes our experimental observations

Applying a Virtual Economy Model in Mexico's Oil Sector

International Nuclear Information System (INIS)

Baker, G.

1994-01-01

The state of Mexico's oil industry, including the accomplishments of Pemex, Mexico's national oil company, was discussed, with particular reference to the progress made in the period of 1988-1994, and the outlook for innovations in the post-Salinas era. The concept of an evolutionary trend from a command economy (State as sole producer), towards market (State as regulator) or mixed economies (State as business partner) in developing countries, was introduced, placing Pemex within this evolutionary model as moving away from centralized control of oil production and distribution, while achieving international competitiveness. The concept of ''virtual market economy'' was also discussed. This model contains the legal basis of a command economy, while instituting modernization programs in order to stimulate market-economic conditions. This type of economy was considered particularly useful in this instance, sine it would allow Pemex units to operate within international performance and price benchmarks while maintaining state monopoly. Specific details of how Pemex could transform itself to a virtual market economy were outlined. It was recommended that Pemex experiment with the virtual mixed economy model; in essence, making the state a co-producer, co-transporter, and co-distributor of hydrocarbons. The effects of such a move would be to bring non-debt funding to oil and gas production, transmission, and associated industrial activities

A randomized, controlled cross-over trial of dermally-applied lavender (Lavandula angustifolia) oil as a treatment of agitated behaviour in dementia.

Science.gov (United States)

O'Connor, Daniel W; Eppingstall, Barbara; Taffe, John; van der Ploeg, Eva S

2013-11-13

Lavender essential oil shows evidence of sedative properties in neurophysiological and animal studies but clinical trials of its effectiveness as a treatment of agitation in people with dementia have shown mixed results. Study methods have varied widely, however, making comparisons hazardous. To help remedy previous methodological shortcomings, we delivered high grade lavender oil in specified amounts to nursing home residents whose agitated behaviours were recorded objectively. 64 nursing home residents with frequent physically agitated behaviours were entered into a randomized, single-blind cross-over trial of dermally-applied, neurophysiologically active, high purity 30% lavender oil versus an inactive control oil. A blinded observer counted the presence or absence of target behaviours and rated participants' predominant affect during each minute for 30 minutes prior to exposure and for 60 minutes afterwards. Lavender oil did not prove superior to the control oil in reducing the frequency of physically agitated behaviours or in improving participants' affect. Studies of essential oils are constrained by their variable formulations and uncertain pharmacokinetics and so optimal dosing and delivery regimens remain speculative. Notwithstanding this, topically delivered, high strength, pure lavender oil had no discernible effect on affect and behaviour in a well-defined clinical sample. Australian and New Zealand Clinical Trials Registry (ACTRN 12609000569202).

A Lithium-Air Battery Stably Working at High Temperature with High Rate Performance.

Science.gov (United States)

Pan, Jian; Li, Houpu; Sun, Hao; Zhang, Ye; Wang, Lie; Liao, Meng; Sun, Xuemei; Peng, Huisheng

2018-02-01

Driven by the increasing requirements for energy supply in both modern life and the automobile industry, the lithium-air battery serves as a promising candidate due to its high energy density. However, organic solvents in electrolytes are likely to rapidly vaporize and form flammable gases under increasing temperatures. In this case, serious safety problems may occur and cause great harm to people. Therefore, a kind of lithium-air that can work stably under high temperature is desirable. Herein, through the use of an ionic liquid and aligned carbon nanotubes, and a fiber shaped design, a new type of lithium-air battery that can effectively work at high temperatures up to 140 °C is developed. Ionic liquids can offer wide electrochemical windows and low vapor pressures, as well as provide high thermal stability for lithium-air batteries. The aligned carbon nanotubes have good electric and heat conductivity. Meanwhile, the fiber format can offer both flexibility and weavability, and realize rapid heat conduction and uniform heat distribution of the battery. In addition, the high temperature has also largely improved the specific powers by increasing the ionic conductivity and catalytic activity of the cathode. Consequently, the lithium-air battery can work stably at 140 °C with a high specific current of 10 A g -1 for 380 cycles, indicating high stability and good rate performance at high temperatures. This work may provide an effective paradigm for the development of high-performance energy storage devices. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Applied multiphase flow in pipes and flow assurance oil and gas production

CERN Document Server

Al-Safran, Eissa M

2017-01-01

Applied Multiphase Flow in Pipes and Flow Assurance - Oil and Gas Production delivers the most recent advancements in multiphase flow technology while remaining easy to read and appropriate for undergraduate and graduate petroleum engineering students. Responding to the need for a more up-to-the-minute resource, this highly anticipated new book represents applications on the fundamentals with new material on heat transfer in production systems, flow assurance, transient multiphase flow in pipes and the TUFFP unified model. The complex computation procedure of mechanistic models is simplified through solution flowcharts and several example problems. Containing over 50 solved example problems and 140 homework problems, this new book will equip engineers with the skills necessary to use the latest steady-state simulators available.

A stably expressed llama single-domain intrabody targeting Rev displays broad-spectrum anti-HIV activity.

Science.gov (United States)

Boons, Eline; Li, Guangdi; Vanstreels, Els; Vercruysse, Thomas; Pannecouque, Christophe; Vandamme, Anne-Mieke; Daelemans, Dirk

2014-12-01

The HIV Rev protein mediates the transport of partially and unspliced HIV mRNA from the nucleus to the cytoplasm. Rev multimerizes on a secondary stem-loop structure present in the viral intron-containing mRNA species and recruits the cellular karyopherin CRM1 to export viral mRNAs from the nucleus to the cytoplasm. Previously we have identified a single-domain intrabody (Nb(190)), derived from a llama heavy-chain antibody, which efficiently inhibits Rev multimerization and suppresses the production of infectious virus. We recently mapped the epitope of this nanobody and demonstrated that Rev residues K20 and Y23 are crucial for interaction while residues V16, H53 and L60 are important to a lesser extent. Here, we generated cell lines stably expressing Nb(190) and assessed the capacity of these cell lines to suppress the replication of different HIV-1 subtypes. These cells stably expressing the single-domain antibody are protected from virus-induced cytopathogenic effect even in the context of high multiplicity of infection. In addition, the replication of different subtypes of group M and one strain of group O is significantly suppressed in these cell lines. Next, we analysed the natural variations of Rev amino acids in sequence samples from HIV-1 infected patients worldwide and assessed the effect of Nb(190) on the most prevalent polymorphisms occurring at the key epitope positions (K20 and Y23) in Rev. We found that Nb(190) was able to suppress the function of these Rev variants except for the K20N mutant, which was present in only 0.7% of HIV-1 sequence populations (n = 4632). Cells stably expressing the single-domain intrabody Nb(190) are protected against virus-induced cytopathogenic effect and display a selective survival advantage upon infection. In addition, Nb(190) suppresses the replication of a wide range of different HIV-1 subtypes. Large-scale sequence analysis reveals that the Nb(190) epitope positions in Rev are well conserved across major HIV-1

RISK ANALYSIS APPLIED IN OIL EXPLORATION AND PRODUCTION

African Journals Online (AJOL)

ES Obe

aDepartment of Civil Engineering, University of Nigeria, Nsukka, Enugu State, Nigeria. ... The analysis in this work is ... risk analysis, oil field, risk management, projects, investment opportunity. 1. .... own merit but since the company has limited.

The Svalbard intertidal zone: a concept for the use of GIS in applied oil sensitivity, vulnerability and impact analyses

International Nuclear Information System (INIS)

Moe, K.A.; Skeie, G.M.; Brude, O.W.; Loevas, S.M.; Nedreboes, M.; Weslawski, J.M.

2000-01-01

Historical oil spills have shown that environmental damage on the seashore can be measured by acute mortality of single species and destabilisation of the communities. The biota, however, has the potential to recover over some period of time. Applied to the understanding of the fate of oil and population and community dynamics, the impact can be described by the function of the following two factors: the immediate extent and the duration of damage. A simple and robust mathematical model is developed to describe this process in the Svalbard intertidal. Based on the integral of key biological and physical factors, i.e., community specific sensitivity, oil accumulation and retention capacity of the substrate, ice-cover and wave exposure, the model is implemented by a Geographical Information System (GIS) for characterisation of the habitat's sensitivity and vulnerability. Geomorphologic maps and georeferenced biological data are used as input. Digital maps of intertidal zone are compiled, indicating the shoreline sensitivity and vulnerability in terms of coastal segments and grid aggregations. Selected results have been used in the national assessment programme of oil development in the Barents Sea for priorities in environmental impact assessments and risk analyses as well as oil spill contingency planning. (Author)

Natural cold pressed oils as cosmetic products

Directory of Open Access Journals (Sweden)

Małgorzata Ligęza

2016-12-01

Full Text Available Background. It seems that patients may ask general practitioners about natural cosmetics applied on the skin regarding their safety and suitability. Objectives. The aim of the study was to analyze natural cold pressed oils as potential cosmetic products. Material and methods. Cold pressed oils obtained from selected seeds and fruit stones were analyzed, including: chokeberry seed oil, blackcurrant seed oil, elderberry seed oil, raspberry seed oil, apricot seed oil, tomato seed oil, strawberry seed oil, broccoli seed oil, Nigella sativa seed oil, hemp oil, safflower seed oil, Silybum marianum seed oil and coconut oil. 80 adult volunteers assessed the cosmetic properties of the analyzed oils. Each of the volunteers tested 2 to 4 different oils, by applying them on the skin. In addition, patch tests with all analyzed oils were performed on 23 individuals. Results. The majority of tested oils were positively evaluated by the participants: in the opinion of the participants, oil extracted from safflower had the best appearance (100% positive opinions, coconut oil had the best smell (70% positive opinions, while black currant seed oil showed the best absorbency (85% positive opinions. No irritation was observed within the analyzed product group, albeit one allergic reaction to apricot seed oil was observed with patch testing. Conclusions . Based on the achieved results, it could be suggested that natural cold pressed oils can be applied to the skin as cosmetics. Our observations may be helpful for general practitioners when choosing natural cosmetics.

Validation of Fluorescence Spectroscopy to Detect Adulteration of Edible Oil in Extra Virgin Olive Oil (EVOO) by Applying Chemometrics.

Science.gov (United States)

Ali, Hina; Saleem, Muhammad; Anser, Muhammad Ramzan; Khan, Saranjam; Ullah, Rahat; Bilal, Muhammad

2018-01-01

Due to high price and nutritional values of extra virgin olive oil (EVOO), it is vulnerable to adulteration internationally. Refined oil or other vegetable oils are commonly blended with EVOO and to unmask such fraud, quick, and reliable technique needs to be standardized and developed. Therefore, in this study, adulteration of edible oil (sunflower oil) is made with pure EVOO and analyzed using fluorescence spectroscopy (excitation wavelength at 350 nm) in conjunction with principal component analysis (PCA) and partial least squares (PLS) regression. Fluorescent spectra contain fingerprints of chlorophyll and carotenoids that are characteristics of EVOO and differentiated it from sunflower oil. A broad intense hump corresponding to conjugated hydroperoxides is seen in sunflower oil in the range of 441-489 nm with the maximum at 469 nm whereas pure EVOO has low intensity doublet peaks in this region at 441 nm and 469 nm. Visible changes in spectra are observed in adulterated EVOO by increasing the concentration of sunflower oil, with an increase in doublet peak and correspondingly decrease in chlorophyll peak intensity. Principal component analysis showed a distinct clustering of adulterated samples of different concentrations. Subsequently, the PLS regression model was best fitted over the complete data set on the basis of coefficient of determination (R 2 ), standard error of calibration (SEC), and standard error of prediction (SEP) of values 0.99, 0.617, and 0.623 respectively. In addition to adulterant, test samples and imported commercial brands of EVOO were also used for prediction and validation of the models. Fluorescence spectroscopy combined with chemometrics showed its robustness to identify and quantify the specified adulterant in pure EVOO.

The oil market. Call on OPEC determines the oil price

International Nuclear Information System (INIS)

Kingma, D.; Mulder, M.

2001-01-01

Several scenarios are applied to determine the oil price for the medium-long term, based on the so-called 'call on OPEC'. The 'call on OPEC' is part of the demand for oil which has to supplied by OPEC. It is expected that the nominal oil price will be circa $24 per barrel in 2004, based on a global growth of 4%. 2 refs

Applying CFD in the Analysis of Heavy Oil/Water Separation Process via Hydrocyclone

OpenAIRE

K Angelim; A De Lima; J Souza; S Neto; V Oliveira; G Moreira

2017-01-01

In recent years most of the oil reserves discovered has been related to heavy oil reservoirs whose reserves are abundant but still show operational difficulties. This fact provoked great interest of the petroleum companies in developing new technologies for increasing the heavy oil production. Produced water generation, effluent recovered from the production wells together with oil and natural gas, is among the greatest potential factors for environmental degradation. Thus, a new scenario of ...

Effectiveness of dispersants on thick oil slicks

International Nuclear Information System (INIS)

Ross, S.; Belore, R.

1993-01-01

Experiments were conducted to determine the relationship between dispersant effectiveness and oil slick thickness, and thereby determine the optimum time for applying dispersant onto spilled oil at sea. Tests were completed at a lab-scale level by varying the three parameters of oil type, dispersant application, and oil thickness. The tests were intended to be comparative only. The primary oils used were Alberta sweet mix blend and Hibernia B-27 crude. The dispersant, Corexit 9527, was applied either premixed with the oil, dropwise in one application, or dropwise in multiple applications to simulate a multi-hit aircraft operation. The apparatus used in the experiment was an oscillating hoop tank, with oil-containing rings used to obtain and maintain uniform slick thickness. The results indicate that the effectiveness potential of a chemical dispersant does not decrease as slick thickness increases. In fact, results of the tests involving Hibernia oil suggest that oils that tend to herd easily would be treated more effectively if dispersant were applied when the oil was relatively thick (1 mm or greater) to avoid herding problems. The oil slicks premixed with dispersant did not disperse well in the thick oil tests, not because of dispersant-oil interaction problems but because of reduced mixing energy. 6 refs., 4 figs., 1 tab

Iranian-Oil-Free Zone and international oil prices

International Nuclear Information System (INIS)

Farzanegan, Mohammad Reza; Raeisian Parvari, Mozhgan

2014-01-01

One of the main elements of economic sanctions against Iran due to its nuclear and military programs is crude oil exportation restrictions in addition to investment in Iranian energy related projects. Senders of such sanction are interested in understanding the impacts of such embargos on international oil prices. We apply unrestricted vector autoregressive (VAR) model, using impulse response functions (IRF) and variance decomposition analysis (VDA) tools with annual data from 1965 to 2012 to analyze the dynamic response of international oil prices to Iranian oil export sanction. Controlling for the supply of non-Iranian oil, the world GDP per capita, and post-Islamic revolution exogenous dummy variables, we show that international oil prices respond negatively and statistically significant to increasing shock in absolute negative changes of the Iranian oil exports – our proxy of Iran oil sanctions – following the first 2 years after shock. The main reason is the positive response of the non-Iranian oil supply to negative shocks in Iranian oil exports, filling the missing supply of Iranian oil in international markets. - Highlights: • We analyze the interconnections between Iranian oil supply and global oil prices. • We use VAR modeling and annual data from 1965 to 2012 for the case of Iran. • There are no inflationary effects of Iranian oil sanction on world oil prices. • Non-Iranian oil supply offsets the missing Iranian oil in the market

Microbial diversity in oiled and un-oiled shoreline sediments in the Norwegian Arctic

International Nuclear Information System (INIS)

Grossman, M.J.; Prince, R.C.; Garrett, R.M.; Garrett, K.K.; Bare, R.E.; O'Neil, K.R.; Sowlay, M.R.; Hinton, S.M.; Lee, K.; Sergy, G.A.; Guenette, C.C.

2000-01-01

Field trials were conducted at an oiled shoreline on the island of Spitsbergen to examine the effect of nutrient addition on the metabolic status, potential for aromatic hydrocarbon degradation, and the phylogenetic diversity of the microbial community in oiled Arctic shoreline sediments. IF-30 intermediate fuel grade oil was applied to the shoreline which was then divided into four plots. One was left untreated and two were tilled. Four applications of fertilizer were applied over a two-month period. Phospholipid fatty acid (PLFA), gene probe and 16S microbial community analysis suggested that bioremediation stimulated the metabolic activity, increased microbial biomass and genetic potential for aromatic hydrocarbon degradation, and increased the population of hydrocarbon degradation of an oiled Arctic shoreline microbial community. The results of this study are in agreement with the results from stimulation of oil biodegradation in temperate marine environments. It was concluded that biodegradation and fertilizer addition are feasible treatment methods for oil spills in Arctic regions. 31 refs., 3 tabs., 3 figs

Optimization of the ethanolysis of Raphanus sativus (L. Var.) crude oil applying the response surface methodology.

Science.gov (United States)

Domingos, Anderson Kurunczi; Saad, Emir Bolzani; Wilhelm, Helena Maria; Ramos, Luiz Pereira

2008-04-01

Raphanus sativus (L. Var) is a perennial plant of the Brassicaceae (or Cruciferae) family whose oil has not been investigated in detail for biodiesel production, particularly when ethanol is used as the alcoholysis agent. In this work, response surface methodology (RSM) was used to determine the optimum condition for the ethanolysis of R. sativus crude oil. Three process variables were evaluated at two levels (2(3) experimental design): the ethanol:oil molar ratio (6:1 and 12:1), the catalyst concentration in relation to oil mass (0.4 and 0.8 wt% NaOH) and the alcoholysis temperature (45 and 65 degrees C). When the experimental results were tentatively adjusted by linear regression, only 58.15% of its total variance was explained. Therefore, a quadratic model was investigated to improve the poor predictability of the linear model. To apply the quadratic model, the 2(3) experimental design had to be expanded to a circumscribed central composite design. This allowed the development of a response surface that was able to predict 97.75% of the total variance of the system. Validation was obtained by performing one ethanolysis experiment at the conditions predicted by the model (38 degrees C, ethanol:oil molar ratio of 11.7:1 and 0.6 wt% NaOH). The resulting ester yield (104.10 wt% or 99.10% of the theoretical yield of 105.04 wt%) was shown to be the highest among all conditions tested in this study. The second ethanolysis stage of the best RSM product required 50% less ethanol and 90% less catalyst consumption. The amount of ethyl esters obtained after this procedure reached 94.5% of the theoretical yield. The resulting ethyl esters were shown to comply with most of the Brazilian biodiesel specification parameters except for oxidation stability. Addition of 500 ppm of BHT to the esters, however, complied with the specification target of 6h. The application of 2 wt% Magnesol after the second ethanolysis stage eliminated the need for water washing and helped generate a

Oil Spill Response Manual

NARCIS (Netherlands)

Marieke Zeinstra; Sandra Heins; Wierd Koops

2014-01-01

A two year programme has been carried out by the NHL University of Applied Sciences together with private companies in the field of oil and chemical spill response to finalize these manuals on oil and chemical spill response. These manuals give a good overview of all aspects of oil and chemical

Evaluation of reference genes for quantitative real-time PCR in oil palm elite planting materials propagated by tissue culture.

Directory of Open Access Journals (Sweden)

Pek-Lan Chan

Full Text Available BACKGROUND: The somatic embryogenesis tissue culture process has been utilized to propagate high yielding oil palm. Due to the low callogenesis and embryogenesis rates, molecular studies were initiated to identify genes regulating the process, and their expression levels are usually quantified using reverse transcription quantitative real-time PCR (RT-qPCR. With the recent release of oil palm genome sequences, it is crucial to establish a proper strategy for gene analysis using RT-qPCR. Selection of the most suitable reference genes should be performed for accurate quantification of gene expression levels. RESULTS: In this study, eight candidate reference genes selected from cDNA microarray study and literature review were evaluated comprehensively across 26 tissue culture samples using RT-qPCR. These samples were collected from two tissue culture lines and media treatments, which consisted of leaf explants cultures, callus and embryoids from consecutive developmental stages. Three statistical algorithms (geNorm, NormFinder and BestKeeper confirmed that the expression stability of novel reference genes (pOP-EA01332, PD00380 and PD00569 outperformed classical housekeeping genes (GAPDH, NAD5, TUBULIN, UBIQUITIN and ACTIN. PD00380 and PD00569 were identified as the most stably expressed genes in total samples, MA2 and MA8 tissue culture lines. Their applicability to validate the expression profiles of a putative ethylene-responsive transcription factor 3-like gene demonstrated the importance of using the geometric mean of two genes for normalization. CONCLUSIONS: Systematic selection of the most stably expressed reference genes for RT-qPCR was established in oil palm tissue culture samples. PD00380 and PD00569 were selected for accurate and reliable normalization of gene expression data from RT-qPCR. These data will be valuable to the research associated with the tissue culture process. Also, the method described here will facilitate the selection

Evaluation of Reference Genes for Quantitative Real-Time PCR in Oil Palm Elite Planting Materials Propagated by Tissue Culture

Science.gov (United States)

Chan, Pek-Lan; Rose, Ray J.; Abdul Murad, Abdul Munir; Zainal, Zamri; Leslie Low, Eng-Ti; Ooi, Leslie Cheng-Li; Ooi, Siew-Eng; Yahya, Suzaini; Singh, Rajinder

2014-01-01

Background The somatic embryogenesis tissue culture process has been utilized to propagate high yielding oil palm. Due to the low callogenesis and embryogenesis rates, molecular studies were initiated to identify genes regulating the process, and their expression levels are usually quantified using reverse transcription quantitative real-time PCR (RT-qPCR). With the recent release of oil palm genome sequences, it is crucial to establish a proper strategy for gene analysis using RT-qPCR. Selection of the most suitable reference genes should be performed for accurate quantification of gene expression levels. Results In this study, eight candidate reference genes selected from cDNA microarray study and literature review were evaluated comprehensively across 26 tissue culture samples using RT-qPCR. These samples were collected from two tissue culture lines and media treatments, which consisted of leaf explants cultures, callus and embryoids from consecutive developmental stages. Three statistical algorithms (geNorm, NormFinder and BestKeeper) confirmed that the expression stability of novel reference genes (pOP-EA01332, PD00380 and PD00569) outperformed classical housekeeping genes (GAPDH, NAD5, TUBULIN, UBIQUITIN and ACTIN). PD00380 and PD00569 were identified as the most stably expressed genes in total samples, MA2 and MA8 tissue culture lines. Their applicability to validate the expression profiles of a putative ethylene-responsive transcription factor 3-like gene demonstrated the importance of using the geometric mean of two genes for normalization. Conclusions Systematic selection of the most stably expressed reference genes for RT-qPCR was established in oil palm tissue culture samples. PD00380 and PD00569 were selected for accurate and reliable normalization of gene expression data from RT-qPCR. These data will be valuable to the research associated with the tissue culture process. Also, the method described here will facilitate the selection of appropriate

Neural networks applied to characterize blends containing refined and extra virgin olive oils.

Science.gov (United States)

Aroca-Santos, Regina; Cancilla, John C; Pariente, Enrique S; Torrecilla, José S

2016-12-01

The identification and quantification of binary blends of refined olive oil with four different extra virgin olive oil (EVOO) varietals (Picual, Cornicabra, Hojiblanca and Arbequina) was carried out with a simple method based on combining visible spectroscopy and non-linear artificial neural networks (ANNs). The data obtained from the spectroscopic analysis was treated and prepared to be used as independent variables for a multilayer perceptron (MLP) model. The model was able to perfectly classify the EVOO varietal (100% identification rate), whereas the error for the quantification of EVOO in the mixtures containing between 0% and 20% of refined olive oil, in terms of the mean prediction error (MPE), was 2.14%. These results turn visible spectroscopy and MLP models into a trustworthy, user-friendly, low-cost technique which can be implemented on-line to characterize olive oil mixtures containing refined olive oil and EVOOs. Copyright © 2016 Elsevier B.V. All rights reserved.

Simulation of oil pollution in the Persian Gulf near Assaluyeh oil terminal

International Nuclear Information System (INIS)

Faghihifard, M.; Badri, M.A.

2016-01-01

Numerical simulation of oil slick movement with respect to tidal factors and wind effects was performed in order to counteract oil pollution in the Persian Gulf. First, a flow model was invoked with respect to water level fluctuations. The main tidal constituents were applied to the model using the initial conditions of water level variations in the Hormuz Strait near the Hangam Island. The movement of oil pollution was determined due to wind, tide and temperature effects and confirmed by applying a verified field results. Simulations were focused near an important terminal in the Persian Gulf, Assaluyeh Port. The results were led to preparing a risk-taking map in a parallel research for the Persian Gulf.

Hydrocarbon oils

Energy Technology Data Exchange (ETDEWEB)

Foorwood, G F; Taplay, J G

1916-12-12

Hydrocarbon oils are hydrogenated, cracked, or treated for the removal of sulfur by bringing their vapors mixed with steam at temperatures between 450 and 600/sup 0/C into contact with a form of carbon that is capable of decomposing steam with the production of nascent hydrogen at those temperatures. The forms of carbon used include lamp-black, soot, charcoals derived from wood, cellulose, and lignite, and carbons obtained by carbonizing oil residues and other organic bodies at temperatures below 600/sup 0/C. The process is applied to the treatment of coal oil, shale oil, petroleum, and lignite oil. In examples, kerosene is cracked at 570/sup 0/C, cracked spirit is hydrogenated at 500/sup 0/C, and shale spirit is desulfurized at 530/sup 0/C. The products are led to a condenser and thence to a scrubber, where they are washed with creosote oil. After desulfurization, the products are washed with dilute caustic soda to remove sulfurretted hydrogen.

Reducing Runoff Loss of Applied Nutrients in Oil Palm Cultivation Using Controlled-Release Fertilizers

Directory of Open Access Journals (Sweden)

A. Bah

2014-01-01

Full Text Available Controlled-release fertilizers are expected to minimize nutrient loss from crop fields due to their potential to supply plant-available nutrients in synchrony with crop requirements. The evaluation of the efficiency of these fertilizers in tropical oil palm agroecological conditions is not yet fully explored. In this study, a one-year field trial was conducted to determine the impact of fertilization with water soluble conventional mixture and controlled-release fertilizers on runoff loss of nutrients from an immature oil palm field. Soil and nutrient loss were monitored for one year in 2012/2013 under erosion plots of 16 m2 on 10% slope gradient. Mean sediments concentration in runoff amounted to about 6.41 t ha−1. Conventional mixture fertilizer posed the greatest risk of nutrient loss in runoff following fertilization due to elevated nitrogen (6.97%, potassium (13.37%, and magnesium (14.76% as percentage of applied nutrients. In contrast, this risk decreased with the application of controlled-release fertilizers, representing 0.75–2.44% N, 3.55–5.09% K, and 4.35–5.43% Mg loss. Meanwhile, nutrient loss via eroded sediments was minimal compared with loss through runoff. This research demonstrates that the addition of controlled-release fertilizers reduced the runoff risks of nutrient loss possibly due to their slow-release properties.

Film Thickness Estimation for the Oil Applied to the Inner Surface of Slim Tubes

Directory of Open Access Journals (Sweden)

Jozef Svetlík

2017-09-01

Full Text Available The article deals with the approximation of the results of experimental measurement of coating of the inner surface of slim pipes with special oil, using a dispersion oil fraction. The reason for such treatment of the inner surface of the tubes is the anti-corrosion protection or various other requirements. The oil manufacturer prescribes the minimum required layer to guarantee the anti-corrosion protection parameters. Therefore, it is advisable to know the most exact coating parameters for different pipe diameters. The measured results give us an assumption of how much oil is sufficient to coat the inside of a pipe. The main idea lies in the correct estimation of coefficients in the three-parameter exponential dependence. For the initial estimates, Nelder–Mead’s minimization method was used. The condition for meeting the lower estimate of the minimum thickness of the oil layer was determined. Following graphic processing of minimization of individual pipe diameters, in some cases, the coefficients were adjusted manually. The result is that the oil thickness depends on the distance of the investigated point from the beginning of the tube, or on the point of entry of the dispersion oil fraction.

Essential Oils for Alternative Teak Rust Control

Directory of Open Access Journals (Sweden)

Pedro Raymundo Argüelles Osorio

2018-03-01

Full Text Available ABSTRACT The objectives of this study were to evaluate the effect of lemon grass, citronella grass, Mexican-tea and noni essential oils on urediniospore germination of Olivea neotectonae , the agent responsible for rust in Teak (Tectona grandis L.f.; to evaluate the phytotoxic effect of these essential oils on teak seedlings; and to evaluate the use of essential oils to control rust in teak plants when preventively and curatively applied. We found that the noni and lemon grass essential oils inhibited 100% of urediniospore germination. On the other hand, the essential oils from noni and lemon grass caused phytotoxicity when applied to seedlings at concentrations of 2000 and 1500 μL L-1, respectively. The major constituents found in lemon grass essential oil were Geranial and Neral, while Octanoic Acid was found in noni oil. Lower values in the area below the rust progress curve were observed with the preventive application of lemon grass and noni essential oils.

Oils, paintings and chemistry

Directory of Open Access Journals (Sweden)

Maria Eduarda Machado de Araújo

2005-01-01

Full Text Available In oil paintings artists use oils to apply pigments. These oils firstly are liquid and then solidify in a thin film. Many chemical reactions are involved in drying and also in the aging of these oils. Drying is a continuous process that begins with the oxidation of insaturated fatty acids from triglycerides to originate peroxides. These compounds suffer a cascade of reactions that lead to cross linking bonds between fatty acids residues, transforming the oil in a solid film. Identification of the film oil is possible using the palmitic/stearic ratio (P/S by chromatographic (GC and/or spectroscopic techniques. Sterol composition, phytosterols or cholesterol, determined by GC-MS or FTIR techniques, allows investigators to distinguish between oil painting and a temper one that used egg as the binding medium.

Financial oil derivatives: from options to oil warrants and synthetic oilfields

International Nuclear Information System (INIS)

Trabia, Xavier

1992-01-01

This study aims to shed light on some of the most interesting financial oil derivatives issued so far in order to assess the potential of this new wave of innovative funding instruments. In Part I some theoretical background is provided and applied to the problem of the American futures option. The ''binomial'' model for valuing future option contracts is presented and the most accurate alternatives for pricing American futures options are reviewed. The role of these numerical procedures in valuing more complex options involved in oil warrants is examined. Comments are made on the behaviour of volatility, which stands as a key interface between theory and practice in oil trading on the oil futures market. Part II of the study describes in detail some of the most famous new financial oil derivatives. Some final conclusions are drawn on the potential of oil trusts and synthetic oilfields to be involved in project and general funding in the oil industry. (44 figures, 11 tables, 53 references) (UK)

Managing and Harnessing Volatile Oil Windfalls

NARCIS (Netherlands)

van den Bremer, T.S.; van der Ploeg, F.

2013-01-01

Three funds are necessary to manage an oil windfall: intergenerational, liquidity, and investment funds. The optimal liquidity fund is bigger if the windfall lasts longer and oil price volatility, prudence, and the GDP share of oil rents are high and productivity growth is low. The paper applies the

Short wavelength Raman spectroscopy applied to the discrimination and characterization of three cultivars of extra virgin olive oils in different maturation stages.

Science.gov (United States)

Gouvinhas, Irene; Machado, Nelson; Carvalho, Teresa; de Almeida, José M M M; Barros, Ana I R N A

2015-01-01

Extra virgin olive oils produced from three cultivars on different maturation stages were characterized using Raman spectroscopy. Chemometric methods (principal component analysis, discriminant analysis, principal component regression and partial least squares regression) applied to Raman spectral data were utilized to evaluate and quantify the statistical differences between cultivars and their ripening process. The models for predicting the peroxide value and free acidity of olive oils showed good calibration and prediction values and presented high coefficients of determination (>0.933). Both the R(2), and the correlation equations between the measured chemical parameters, and the values predicted by each approach are presented; these comprehend both PCR and PLS, used to assess SNV normalized Raman data, as well as first and second derivative of the spectra. This study demonstrates that a combination of Raman spectroscopy with multivariate analysis methods can be useful to predict rapidly olive oil chemical characteristics during the maturation process. Copyright © 2014 Elsevier B.V. All rights reserved.

Trends in Controllable Oil Film Bearings

DEFF Research Database (Denmark)

Santos, Ilmar

2011-01-01

This work gives an overview about the theoretical and experimental achievements of mechatronics applied to oil film bearings, with the aim of: controlling the lateral vibration of flexible rotating shafts; modifying bearing dynamic characteristics, as stiffness and damping properties; increasing......" components and be applied to rotating machines with the goal of avoiding unexpected stops of plants, performing rotordynamic tests and identifying model parameters "on site". Emphasis is given to the controllable lubrication (active lubrication) applied to different types of oil film bearings, i...

Enhancement of Crude Oil Polluted Soil by Applying Single and ...

African Journals Online (AJOL)

ADOWIE PERE

bioline.org.br/ja ... 5 kg of soil each was polluted with 200 ml of crude oil ... organic matter, phosphate, nitrate, total hydrocarbon content, potassium and microbial population were analyzed before ... arise mainly from the processing and distribution of.

Synthesis of zinc aluminate with high surface area by microwave hydrothermal method applied in the transesterification of soybean oil (biodiesel)

International Nuclear Information System (INIS)

Quirino, M.R.; Oliveira, M.J.C.; Keyson, D.; Lucena, G.L.; Oliveira, J.B.L.; Gama, L.

2016-01-01

Highlights: • ZnAl_2O_4 spinel was synthesized by the microwave hydrothermal method in only 15 or 30 min. • The powders show high specific surface area. • ZAT_b15 showed activity of 52.22% for the conversion of soybean oil into biodiesel. - Abstract: Zinc aluminate is a material with high thermal stability and high mechanical strength that, owing to these properties, is used as a catalyst or support. In this work, zinc aluminate spinel was synthesized by the microwave hydrothermal method in only 15 or 30 min at a low temperature (150 °C) without templates, using only Al(NO_3)_3·9H_2O, Zn(NO_3)_2·6H_2O, and urea as precursors and applied in the transesterification of soybean oil. X-ray diffraction analysis showed that ZnAl_2O_4 had a cubic structure without secondary phases. The nitrogen adsorption measurements (BET) revealed a high surface area (266.57 m"2 g"−"1) for the nanopowder synthesized in 15 min. This powder showed activity of 52.22% for the catalytic conversion of soybean oil into biodiesel by transesterification.

The asymmetric relationship between oil revenues and economic activities: The case of oil-exporting countries

International Nuclear Information System (INIS)

Mehrara, Mohsen

2008-01-01

This paper examines the nonlinear or asymmetric relationship between oil revenues and output growth in oil-exporting countries, applying a dynamic panel framework and two different measures of oil shocks. The main results in this paper confirm the stylized facts that in heavily oil-dependent countries lacking the institutional mechanisms de-linking fiscal expenditure from current revenue, oil revenue shocks tend to affect the output in asymmetric and nonlinear ways. The findings suggest that output growth is adversely affected by the negative oil shocks, while oil booms or the positive oil shocks play a limited role in stimulating economic growth. The findings have practical policy implications for decision makers in the area of macroeconomic planning. The use of stabilization and savings funds and diversification of the real sector seems crucial to minimize the harmful effects of oil booms and busts

Oil price movements and production agreements

International Nuclear Information System (INIS)

Mazraati, M.

2004-01-01

The purpose of this technical exercise is to apply econometric modelling to study the relationship between movements in the oil price and compliance by the Organization of the Petroleum Exporting Countries (OPEC) with its self-assigned production agreements, whose purpose is to bring order and stability to the international oil market. After introducing various methods of measurement of compliance, the study applies these methods to monthly data for 1995-2002 for OPEC. It then identifies the method ''over-production as a percentage of ceiling'' as the best-fitting and most accurate criterion for measuring OPEC compliance. The paper then elaborates on intervention analysis, explains the various types of intervention in detail and introduces a number of econometric models to monitor oil price movements resulting from OPEC's intervention in the oil market, along with the extent of its compliance with its agreements. On applying the models to a set of historical monthly data, the study finds that higher oil prices have been achieved when the effective level of compliance lies in the range of 94-99 per cent, and that lower oil prices have been experienced when there is less compliance and more volatility. The paper notes that the achievement of order and stability is the responsibility of all parties in an international market that is inherently volatile. (author)

Possibility for use essential oils in veterinary medicine and animal husbandry with special emphasis on oregano oil

Directory of Open Access Journals (Sweden)

Vučinić Marijana

2012-01-01

Full Text Available The paper reviews the latest studies on possible applications of oregano essential oil in veterinary medicine and animal livestock production. The first part of the paper deals with the definition of essential oils, possibilities for their extraction from plants, possibilities for their application in human and veterinary medicine, the interest of a science in essential oils, and, essential oils classification based on their use in human and veterinary medicine. The second part of the review deals with the properties of oregano essential oil, its main active principles, carvacrol and thymol and its application in veterinary medicine and animal livestock production. Oregano essential oil may be applied in animal feed, in the treatment of coccidiosis of domestic animals and candidiasis. It can be applied as a larvicide, repellent, insecticide and acaricide. It is used in aquaculture to treat fish diseases caused by bacteria and parasites or in the hatchery industry as a disinfectant for eggs or for disinfection of manure. The greatest potential of oregano essential oil is the possibility of its application in organic agriculture and organic animal husbandry. [Projekat Ministarstva nauke Republike Srbije, br. TR 31087

46 CFR 58.01-10 - Fuel oil.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Fuel oil. 58.01-10 Section 58.01-10 Shipping COAST GUARD... SYSTEMS General Requirements § 58.01-10 Fuel oil. (a) The following limits apply to the use of oil as fuel: (1) Except as otherwise permitted by this section, no fuel oil with a flashpoint of less than 60 °C...

Repellent effectiveness of seven plant essential oils, sunflower oil and natural insecticides against horn flies on pastured dairy cows and heifers.

Science.gov (United States)

Lachance, S; Grange, G

2014-06-01

Plant essential oils (basil, geranium, balsam fir, lavender, lemongrass, peppermint, pine and tea tree), mixed with either sunflower oil or ethyl alcohol, were applied at 5% concentrations to the sides of Holstein cattle. Pastured cattle treated with essential oils diluted in sunflower oil had less flies than the untreated control for a 24-h period. However, the essential oil treatments were not significantly different than the carrier oil alone. Barn-held heifers treated with essential oils and sunflower oil alone had significantly less flies than the untreated control for up to 8 h after treatment. Basil, geranium, lavender, lemongrass and peppermint repelled more flies than sunflower oil alone for a period ranging from 1.5 to 4 h after treatments applied to heifers. All essential oils repelled > 75% of the flies on the treated area for 6 and 8 h on pastured cows and indoor heifers, respectively. Geranium, lemongrass and peppermint stayed effective for a longer duration. Essential oils mixed with ethyl alcohol demonstrated less repellence than when mixed with the carrier oil. Safer's soap, natural pyrethrins without piperonyl butoxide and ethyl alcohol alone were not efficient at repelling flies. Essential oils could be formulated for use as fly repellents in livestock production. © 2013 The Royal Entomological Society.

ANALYSIS OF TIME MANAGEMENT APPLIED TO A PROJECT OF OIL

Directory of Open Access Journals (Sweden)

Arielle Meireles Moreira

2011-05-01

Full Text Available Project management (PM efficient results in increased probability of success of activities and its completion as time, cost and scope planned. Since this triad (time, cost and scope is connected, any changes will affect within the scope and increase the cost of the project. This was a case study in a large company exploiting oil and gas. The research is focused on time management (TM in an oil project in order to examine the schedule of activities according to the time tool, the Gantt Chart in MS Project 2003 software. The study design was selected due to its long delay in implementation and lack of planning and managing this. By analyzing the Gantt Chart, activities were identified late. With this, the problems that caused delays were surveyed (the project documents and their parents questioned. Thus, it was proposed improvements to an effective control of time on the problems encountered.

Construction of VLCC marine oil storage cost index system

Science.gov (United States)

Li, Yuan; Li, Yule; Lu, Jinshu; Wu, Wenfeng; Zhu, Faxin; Chen, Tian; Qin, Beichen

2018-04-01

VLCC as the research object, the basic knowledge of VLCC is summarized. According to the phenomenon that VLCC is applied to offshore oil storage gradually, this paper applies the theoretical analysis method to analyze the excess capacity from VLCC, the drop of oil price, the aging VLCC is more suitable for offshore storage The paper analyzes the reason of VLCC offshore oil storage from three aspects, analyzes the cost of VLCC offshore storage from the aspects of manpower cost and shipping cost, and constructs the cost index system of VLCC offshore oil storage.

Synthesis of zinc aluminate with high surface area by microwave hydrothermal method applied in the transesterification of soybean oil (biodiesel)

Energy Technology Data Exchange (ETDEWEB)

Quirino, M.R. [Chemistry Laboratory of Federal University of Paraiba (LABQUIM), Campus III, 58200-000 Bananeiras, PB (Brazil); Oliveira, M.J.C. [Academic Unit of Materials Engineering, UFCG, Campina Grande Campus I, 58429-900 Campina Grande, PB (Brazil); Keyson, D. [Laboratory of study in Science, DME, Federal University of Paraíba, Campus I, 58051-900 João Pessoa, PB (Brazil); Lucena, G.L., E-mail: guilherme_leo1@yahoo.com.br [Chemistry Laboratory of Federal University of Paraiba (LABQUIM), Campus III, 58200-000 Bananeiras, PB (Brazil); Oliveira, J.B.L. [Federal University of Rio Grande do Norte, UFRN, Campus I, 59078-970 Natal, RN (Brazil); Gama, L. [Academic Unit of Materials Engineering, UFCG, Campina Grande Campus I, 58429-900 Campina Grande, PB (Brazil)

2016-02-15

Highlights: • ZnAl{sub 2}O{sub 4} spinel was synthesized by the microwave hydrothermal method in only 15 or 30 min. • The powders show high specific surface area. • ZAT{sub b}15 showed activity of 52.22% for the conversion of soybean oil into biodiesel. - Abstract: Zinc aluminate is a material with high thermal stability and high mechanical strength that, owing to these properties, is used as a catalyst or support. In this work, zinc aluminate spinel was synthesized by the microwave hydrothermal method in only 15 or 30 min at a low temperature (150 °C) without templates, using only Al(NO{sub 3}){sub 3}·9H{sub 2}O, Zn(NO{sub 3}){sub 2}·6H{sub 2}O, and urea as precursors and applied in the transesterification of soybean oil. X-ray diffraction analysis showed that ZnAl{sub 2}O{sub 4} had a cubic structure without secondary phases. The nitrogen adsorption measurements (BET) revealed a high surface area (266.57 m{sup 2} g{sup −1}) for the nanopowder synthesized in 15 min. This powder showed activity of 52.22% for the catalytic conversion of soybean oil into biodiesel by transesterification.

21-Methylpyrenyl-cholesterol stably and specifically associates with lipoprotein peripheral hemi-membrane: A new labelling tool

Energy Technology Data Exchange (ETDEWEB)

Gaibelet, Gérald [INSERM U563, CHU Purpan, Toulouse (France); CEA, SB2SM and UMR8221 CNRS, IBiTec-Saclay, Gif-sur-Yvette (France); Tercé, François [Université Toulouse III, UMR 1048, Toulouse (France); INSERM U1048, Toulouse (France); Bertrand-Michel, Justine [Université Toulouse III, UMR 1048, Toulouse (France); INSERM U1048, Lipidomic Platform Metatoul, Toulouse (France); Allart, Sophie [Plateau Technique d’Imagerie Cellulaire, INSERM U1043, Toulouse (France); Azalbert, Vincent [Université Toulouse III, UMR 1048, Toulouse (France); INSERM U1048, Toulouse (France); Lecompte, Marie-France [INSERM U563, Faculté de Médecine de Rangueil, Toulouse (France); Collet, Xavier [Université Toulouse III, UMR 1048, Toulouse (France); INSERM U1048, Toulouse (France); Orlowski, Stéphane, E-mail: stephane.orlowski@cea.fr [INSERM U563, CHU Purpan, Toulouse (France); CEA, SB2SM and UMR8221 CNRS, IBiTec-Saclay, Gif-sur-Yvette (France)

2013-11-01

Highlights: •21-Methylpyrenyl-cholesterol specifically and stably associates to lipoproteins. •It is not esterified by LCAT, and thus reliably labels their peripheral hemi-membrane. •HDL vs. LDL are well distinguishable by various fluorescent labelling characteristics. •LDL peripheral hemi-membrane harbors cholesterol-rich ordered lipid (micro)domains. •Cultured cells can be stained by such labelled lipoproteins-mediated delivery. -- Abstract: Lipoproteins are important biological components. However, they have few convenient fluorescent labelling probes currently reported, and their physiological reliability can be questioned. We compared the association of two fluorescent cholesterol derivatives, 22-nitrobenzoxadiazole-cholesterol (NBD-Chol) and 21-methylpyrenyl-cholesterol (Pyr-met-Chol), to serum lipoproteins and to purified HDL and LDL. Both lipoproteins could be stably labelled by Pyr-met-Chol, but virtually not by NBD-Chol. At variance with NBD-Chol, LCAT did not esterify Pyr-met-Chol. The labelling characteristics of lipoproteins by Pyr-met-Chol were well distinguishable between HDL and LDL, regarding dializability, associated probe amount and labelling kinetics. We took benefit of the pyrene labelling to approach the structural organization of LDL peripheral hemi-membrane, since Pyr-met-Chol-labelled LDL, but not HDL, presented a fluorescence emission of pyrene excimers, indicating that the probe was present in an ordered lipid micro-environment. Since the peripheral membrane of LDL contains more sphingomyelin (SM) than HDL, this excimer formation was consistent with the existence of cholesterol- and SM-enriched lipid microdomains in LDL, as already suggested in model membranes of similar composition and reminiscent to the well-described “lipid rafts” in bilayer membranes. Finally, we showed that Pyr-met-Chol could stain cultured PC-3 cells via lipoprotein-mediated delivery, with a staining pattern well different to that observed with NBD

21-Methylpyrenyl-cholesterol stably and specifically associates with lipoprotein peripheral hemi-membrane: A new labelling tool

International Nuclear Information System (INIS)

Gaibelet, Gérald; Tercé, François; Bertrand-Michel, Justine; Allart, Sophie; Azalbert, Vincent; Lecompte, Marie-France; Collet, Xavier; Orlowski, Stéphane

2013-01-01

Highlights: •21-Methylpyrenyl-cholesterol specifically and stably associates to lipoproteins. •It is not esterified by LCAT, and thus reliably labels their peripheral hemi-membrane. •HDL vs. LDL are well distinguishable by various fluorescent labelling characteristics. •LDL peripheral hemi-membrane harbors cholesterol-rich ordered lipid (micro)domains. •Cultured cells can be stained by such labelled lipoproteins-mediated delivery. -- Abstract: Lipoproteins are important biological components. However, they have few convenient fluorescent labelling probes currently reported, and their physiological reliability can be questioned. We compared the association of two fluorescent cholesterol derivatives, 22-nitrobenzoxadiazole-cholesterol (NBD-Chol) and 21-methylpyrenyl-cholesterol (Pyr-met-Chol), to serum lipoproteins and to purified HDL and LDL. Both lipoproteins could be stably labelled by Pyr-met-Chol, but virtually not by NBD-Chol. At variance with NBD-Chol, LCAT did not esterify Pyr-met-Chol. The labelling characteristics of lipoproteins by Pyr-met-Chol were well distinguishable between HDL and LDL, regarding dializability, associated probe amount and labelling kinetics. We took benefit of the pyrene labelling to approach the structural organization of LDL peripheral hemi-membrane, since Pyr-met-Chol-labelled LDL, but not HDL, presented a fluorescence emission of pyrene excimers, indicating that the probe was present in an ordered lipid micro-environment. Since the peripheral membrane of LDL contains more sphingomyelin (SM) than HDL, this excimer formation was consistent with the existence of cholesterol- and SM-enriched lipid microdomains in LDL, as already suggested in model membranes of similar composition and reminiscent to the well-described “lipid rafts” in bilayer membranes. Finally, we showed that Pyr-met-Chol could stain cultured PC-3 cells via lipoprotein-mediated delivery, with a staining pattern well different to that observed with NBD

30 CFR 206.101 - What definitions apply to this subpart?

Science.gov (United States)

2010-07-01

... disposition of oil produced. Gross proceeds also include, but are not limited to, the following examples: (1... MANAGEMENT PRODUCT VALUATION Federal Oil § 206.101 What definitions apply to this subpart? The following... region at least as large as the limits of an oil field, in which oil has similar quality, economic, and...

Rice weevil response to basil oil fumigation

Science.gov (United States)

Basil oil, Ocimum basilicum L., is a volatile plant essential oil that is known to have insecticidal activity against stored product pests such as rice weevil, Sitophilus oryzae (L.). Basil oil was diluted in acetone and applied to a sponge held inside a tea strainer for fumigations in containers wi...

Applying the Analytic Hierarchy Process to Oil Sands Environmental Compliance Risk Management

Science.gov (United States)

Roux, Izak Johannes, III

Oil companies in Alberta, Canada, invested $32 billion on new oil sands projects in 2013. Despite the size of this investment, there is a demonstrable deficiency in the uniformity and understanding of environmental legislation requirements that manifest into increased project compliance risks. This descriptive study developed 2 prioritized lists of environmental regulatory compliance risks and mitigation strategies and used multi-criteria decision theory for its theoretical framework. Information from compiled lists of environmental compliance risks and mitigation strategies was used to generate a specialized pairwise survey, which was piloted by 5 subject matter experts (SMEs). The survey was validated by a sample of 16 SMEs, after which the Analytic Hierarchy Process (AHP) was used to rank a total of 33 compliance risks and 12 mitigation strategy criteria. A key finding was that the AHP is a suitable tool for ranking of compliance risks and mitigation strategies. Several working hypotheses were also tested regarding how SMEs prioritized 1 compliance risk or mitigation strategy compared to another. The AHP showed that regulatory compliance, company reputation, environmental compliance, and economics ranked the highest and that a multi criteria mitigation strategy for environmental compliance ranked the highest. The study results will inform Alberta oil sands industry leaders about the ranking and utility of specific compliance risks and mitigations strategies, enabling them to focus on actions that will generate legislative and public trust. Oil sands leaders implementing a risk management program using the risks and mitigation strategies identified in this study will contribute to environmental conservation, economic growth, and positive social change.

Effect of oils on drug absorption

OpenAIRE

Palin, K.J.

1981-01-01

Oil and emulsion vehicles have been shown to alter the oral absorption of many drugs. This may be due to enhanced lymph flow and/or altered gastro-intestinal motility in the presence of the oils. The oral absorption of a model compound (DOT) in the presence of three chemically different oils, arachis oil, Miglyol 812 and liquid paraffin was investigated in rats, the influence of lymphatic absorption and gastro-intestinal motility being determined. The findings were applied to the for.mulation...

Hydrogenizing oils, asphalts, etc

Energy Technology Data Exchange (ETDEWEB)

1925-03-14

The hydrogenation of carbonaceous solids in presence of combined sulfur, e.g., sulfides as described in the parent specification is applied to the treatment of rock oils, shale oils, resins, ozokerite, asphalt, and the like, or fractions, residues, or acid sludge or other conversion products thereof, alone or mixed. Preferably the hydrogen or other reducing gas is in excess and under pressure, and is either circuited or led through a series of treatment vessels, hydrogen being added for that used. In an example, residues from American crude oil are passed continuously with hydrogen at 200 atmospheres and 450 to 500/sup 0/C over pressed precipitated cobalt sulfide, the issuing gases being cooled to condense the light oil produced.

Quality assessment of biodiesels obtained from pure cooking oils of some feedstocks and their waste oils

International Nuclear Information System (INIS)

Khan, I.; Ansari, T.M.; Manzoor, S.

2017-01-01

Biodiesel being a renewable energy resource possesses compositional variability based on the type of feedstock. Biodiesel is considered a cleaner burning fuel and can be used as pure B100 or blended with petro-diesel. In this study, biodiesel was prepared from pure cooking oils (soybean oil, canola oil, sunflower oil, corn oil) and their waste frying oils by base-catalyzed transesterification with methanol in presence of sodium hydroxide. The optimized experimental parameters were applied to achieve the maximum yield of biodiesel. Various fuel properties like kinematic viscosity, flash point, pour point, cloud point, total acid number, specific gravity, water and sediments, conradson carbon residue, sulfur contents, phosphorous contents, sulphated ash, cetane and copper corrosion were determined and found comparable to ASTM standards. Pure cooking oils, their waste frying oils and prepared biodiesels were characterized by FT-IR. The study showed that the biodiesel derived from waste frying oils can be a promising alternative of the biodiesel from pure cooking oils. (author)

Applying object technology principles to business reengineering in the oil, gas, and petrochemical industries

International Nuclear Information System (INIS)

Davis, J.M.

1996-01-01

The oil, gas, and petrochemical industries face a dilemma, to be financially competitive while complying with strict and expanding environmental, safety, and health regulation. Companies need new tools and techniques, indeed a completely new paradigm for organizing and performing work. They must build efficient and flexible business processes, ones that rely on advanced information systems for improved decision making and productivity. And they must adopt a culture of change and improvement to permit the business to change as the business climate changes. Fortunately, two industry developments are changing the traditional business paradigm in a dramatic way; business reengineering and object technology. Applying principles of object technology in the performance of business reengineering makes available a new form of business modeling that transforms the technique of modeling a business while directly supported the development of its enabling information systems. This modeling technique is called Object Modeling and is becoming an important force in improving business competitiveness

Multivariate statisticalmethods applied to interpretation of saturated biomarkers (Velebit oil field, SE Pannonian Basin, Serbia

Directory of Open Access Journals (Sweden)

TATJANA SOLEVIC

2006-07-01

Full Text Available Twenty-five crude oils originating from the Velebit oil field (SE Pannonian Basin, the most important oil field in Serbia, were investigated. Saturated biomarkers (n-alkanes, isoprenoids, steranes and triterpanes were analyzed by gas chromatography-mass spectrometry (GC-MS. Based on the distribution and abundance of these compounds, a large number of source and maturation parameters were calculated, particularly those most often used in correlation studies of oils. The examined samples were classified according to their origin and level of thermal maturity using factor, cluster and discriminant analyses. According to the source and maturation parameters, combined factor and cluster analyses using the Ward method enabled the categorization of the investigated oils into three groups. The cluster Ward analysis was shown to be of greater susceptibility and reliability. However, in addition to the two aforementioned methods, K-Means cluster analysis and discriminant analysis were shown to be necessary for a more precise and detailed categorization in the case of a large number of samples in one group. Consequently, it was concluded that factor and cluster K-Means andWard analyses can generally be used for the interpretation of saturated biomarkers in correlation studies of oils, but the observed results have to be checked, i.e., confirmed by discriminant analysis.

Coconut Oil

Science.gov (United States)

... known as "medium chain triglycerides." Some of these fats work differently than other types of saturated fat in the body. When applied ... in food amounts. But coconut oil contains a type of fat that can increase cholesterol levels. So people should ...

Combating desertification - fuel oil from jatropha plants in Africa: a systematic approach applied by a GTZ-supported project in Mali, West Africa

International Nuclear Information System (INIS)

Henning, R.K.

1995-01-01

The use of plant oil as an engine fuel has a long and eventful history, and technical developments have largely been completed. The economic conditions, however, do not yet suffice to produce a breakthrough for plant oil use as fuel in most industrialized and developing countries. The approach applied by a pilot project in Mali and described in this paper tries to overcome these economic drawbacks. The primary aim of the project is not the use of plant oil from Jatropha as a fuel per se, but rather to make that fuel use into an incentive that would activate a system combining ecologic, economic and income-generating effects, the latter specifically for women. These effects could materialize only if the non-edible oil of the jatropha plant can find an economically viable use. Since jatropha trees (Jatropha curcas L.) not only bear oil-rich seed, but can also be planted in the form of hedges to protect gardens and fields from foraging animals while warding off soil erosion, this would seem to be a case of positive correlation between energy production and agricultural production: the more energy that is produced by the hedgerows of jatropha, the more food production is strengthened. Of particular importance here is the recycling of the oil cake as organic fertilizer. The technologies used in the jatropha system are the well-known hand-driven or mechanically driven oil presses and with precombustion chambers diesel engines. While various makes, the latter are already available on the local market, the presses can be produced locally at affordable prices. The project's activities focus, accordingly, on training and disseminating the relevant know-how. They do this by using local, often non-governmental institutions and by offering advice to farmers and rural communities interested in the jatropha system. The economic analysis using the UNIDO COMFAR III program shows very positive impacts if both direct and indirect effects are considered. Even in a completely non

Fast-HPLC Fingerprinting to Discriminate Olive Oil from Other Edible Vegetable Oils by Multivariate Classification Methods.

Science.gov (United States)

Jiménez-Carvelo, Ana M; González-Casado, Antonio; Pérez-Castaño, Estefanía; Cuadros-Rodríguez, Luis

2017-03-01

A new analytical method for the differentiation of olive oil from other vegetable oils using reversed-phase LC and applying chemometric techniques was developed. A 3 cm short column was used to obtain the chromatographic fingerprint of the methyl-transesterified fraction of each vegetable oil. The chromatographic analysis took only 4 min. The multivariate classification methods used were k-nearest neighbors, partial least-squares (PLS) discriminant analysis, one-class PLS, support vector machine classification, and soft independent modeling of class analogies. The discrimination of olive oil from other vegetable edible oils was evaluated by several classification quality metrics. Several strategies for the classification of the olive oil were used: one input-class, two input-class, and pseudo two input-class.

Estimation on oil demand and oil saving potential of China's road transport sector

International Nuclear Information System (INIS)

Lin, Boqiang; Xie, Chunping

2013-01-01

China is currently in the stage of industrialization and urbanization, which is characterized by rigid energy demand and rapid growth of energy consumption. Therefore, energy conservation will become a major strategy for China in a transition to low-carbon economy. China's transport industry is of high energy consumption. In 2010, oil consumption in transport industry takes up 38.2% of the country's total oil demand, of which 23.6% is taken up by road transport sector. As a result, oil saving in China's road transport sector is vital to the whole nation. The co-integration method is developed to find a long-run relationship between oil consumption and affecting factors such as GDP, road condition, labor productivity and oil price, to estimate oil demand and to predict future oil saving potential in China's transport sector under different oil-saving scenarios. Monte Carlo simulation is further used for risk analysis. Results show that under BAU condition, oil demand of China's road transport sector will reach 278.5 million ton of oil equivalents (MTOE) in 2020. Oil saving potential will be 86 MTOE and 131 MTOE under moderate oil-saving scenario and advanced oil-saving scenario, respectively. This paper provides a reference to establishing oil saving policy for China's road transport sector. - Highlights: • We adopt the co-integration model to estimate oil demand and oil saving potential of China's road transport sector. • Monte Carlo simulation is further used for risk analysis. • GDP, ratio of classified highway, labor productivity and oil price are main factors affecting oil consumption. • Scenario analysis approach is applied to calculate oil saving potential under different energy saving scenarios. • Future policy for oil conservation in China's road transport sector is suggested

Nanotechnologies in oil production

International Nuclear Information System (INIS)

Alieva, M.K; Kazimov, F.K.; Ismailov, E.

2010-01-01

Extraction of remaining, laboriously developed oil reserves at the last stage of development of deposits require drastically improved methods of oil recovery. From this point of view it is more expedient to apply high-tech nanotechnologies. Application of metal nanoparticles in solutions consisting of conventional reagents (deemulgators, SAA and etc.) allows to improve their rheology considerably to increase permaibility and washing of highly viscous components from the smallest pores. Thus, nanofluids influence layer system on atomic-molecular-ionic level which will lead to a complex synergetic effect from the application of nanotechnologies in oil and gas production.

Productivity assessment of Angola's oil blocks

International Nuclear Information System (INIS)

Barros, Carlos Pestana; Managi, Shunsuke

2009-01-01

This paper analyzes the change in productivity as a result of Angola oil policy from 2001 to 2007. Angola oil blocks are the main source of tax receipts and, therefore, strategically important for public finances. A Malmquist index with the input technological bias is applied to measure productivity change. Oil blocks on average became both more efficient and experienced technological progress. Our results indicate that the traditional growth accounting method, which assumes Hicks neutral technological change, is not appropriate for analyzing changes in productivity for Angola oil blocks. Policy implications are derived. (author)

Purification of radioactive waste oil by a supercritical fluid

International Nuclear Information System (INIS)

Yoo, Jaeryong; Sung, Jinhyun; Park, Kwangheon; Kim, Hongdoo; Kim, Hakwon; Lim, Taeyoon; Yim, Sanghak; Yoon, Weonseob

2006-01-01

The radioactive waste oil from the nuclear industry is potentially hazardous due to its possibility to contaminate soil and underwater. Pollutants in waste oil are generally radioactive heavy metals or organo-metals. Radioactive waste oils are highly viscous fluids that are similar to used-motor oils. Several processes have been developed to regenerated used motor oil, such as acid clay treatment, chemical addition, vacuum distillation, thermal cracking and hydrofinishing. However, these technologies are difficult to apply to separating radioactive nuclides from radioactive waste oils. In recent years, our laboratory developed a membrane method for the regeneration of used motor oils. We applied supercritical Co2 (scCO2) as a viscosity reducing additive to waste oils at a lower process temperature in order to improve membrane permeability and thus the energy saving. However, the membrane cannot filter the contaminants in radioactive waste oil that are not particles, such as radioactive ions in impurity water in the oil. In this paper, we suggest a method extracting clean oil from the radioactive waste oil rather than filtering by a supercritical fluid. We selected R22, a refrigerant, as a solvent for extraction. R22 has a mild critical point - 96.1 .deg. and 49.9bar. Regeneration of waste oils by extracting clean oil using a supercritical fluid such as R22 is easy to handle and reduce secondary wastes. In this paper, we examine the feasibility of R22 in extracting clean oil from radioactive waste oils

HPLC-UV Polyphenolic Profiles in the Classification of Olive Oils and Other Vegetable Oils via Principal Component Analysis

Directory of Open Access Journals (Sweden)

Mireia Farrés-Cebrián

2016-12-01

Full Text Available High performance liquid chromatography-ultraviolet (HPLC-UV was applied to the analysis and characterization of olive oils and other vegetable oils. A chromatographic separation on a Zorbax Eclipse XDB-C8 reversed-phase column was proposed under gradient elution, employing 0.1% formic acid aqueous solution and methanol as mobile phase, for the determination of 14 polyphenols and phenolic acids, allowing us to obtain compositional profiles in less than 20 min. Acceptable sensitivity (limit of detection (LOD values down to 80 µg/L in the best of cases, linearity (r2 higher than 0.986, good run-to-run and day-to-day precisions (relative standard deviation (RSD values lower than 11.5%, and method trueness (relative errors lower than 6.8% were obtained. The proposed HPLC-UV method was then applied to the analysis of 72 oil samples (47 olive oils and 27 vegetable oils including sunflower, soy, corn, and mixtures of them. Analytes were recovered using a liquid–liquid extraction method employing ethanol:water 70:30 (v/v solution and hexane as extracting and defatting solvents, respectively. HPLC-UV polyphenolic profiles using peak areas were then analysed by principal component analysis (PCA to extract information from the most significant data contributing to the characterization and classification of olive oils against other vegetable oils, as well as among Arbequina and Picual olive oil varieties. PCA results showed a noticeable difference between olive oils and the other classes. In addition, a reasonable discrimination of olive oils as a function of fruit varieties was also encountered.

Investigation about the efficiency of the bioaugmentation technique when applied to diesel oil contaminated soils

Directory of Open Access Journals (Sweden)

Adriano Pinto Mariano

2009-10-01

Full Text Available This work investigated the efficiency of the bioaugmentation technique when applied to diesel oil contaminated soils collected at three service stations. Batch biodegradation experiments were carried out in Bartha biometer flasks (250 mL used to measure the microbial CO2 production. Biodegradation efficiency was also measured by quantifying the concentration of hydrocarbons. In addition to the biodegradation experiments, the capability of the studied cultures and the native microorganisms to biodegrade the diesel oil purchased from a local service station, was verified using a technique based on the redox indicator 2,6 -dichlorophenol indophenol (DCPIP. Results obtained with this test showed that the inocula used in the biodegradation experiments were able to degrade the diesel oil and the tests carried out with the native microorganisms indicated that these soils had a microbiota adapted to degrade the hydrocarbons. In general, no gain was obtained with the addition of microorganisms or even negative effects were observed in the biodegradation experiments.Este trabalho investigou a eficiência da técnica do bioaumento quando aplicada a solos contaminados com óleo diesel coletados em três postos de combustíveis. Experimentos de biodegradação foram realizados em frascos de Bartha (250 mL, usados para medir a produção microbiana de CO2. A eficiência de biodegradação também foi quantificada pela concentração de hidrocarbonetos. Conjuntamente aos experimentos de biodegradação, a capacidade das culturas estudadas e dos microrganismos nativos em biodegradar óleo diesel comprado de um posto de combustíveis local, foi verificada utilizando-se a técnica baseada no indicador redox 2,6 - diclorofenol indofenol (DCPIP. Resultados obtidos com esse teste mostraram que os inóculos empregados nos experimentos de biodegradação foram capazes de biodegradar óleo diesel e os testes com os microrganismos nativos indicaram que estes solos

Characteristics of stably expressed human dopamine D1a and D1b receptors: atypical behavior of the dopamine D1b receptor

DEFF Research Database (Denmark)

Pedersen, U B; Norby, B; Jensen, Anders A.

1994-01-01

Human dopamine D1a and D1b receptors were stably expressed in Baby Hamster Kidney (BHK) or Chinese Hamster Ovary (CHO) cells. [3H]SCH23390 saturation experiments indicated the presence of only a single binding site in the D1a expressing cell line with a Kd of 0.5 nM. In D1b expressing cell lines...

[Rapid discriminating hogwash oil and edible vegetable oil using near infrared optical fiber spectrometer technique].

Science.gov (United States)

Zhang, Bing-Fang; Yuan, Li-Bo; Kong, Qing-Ming; Shen, Wei-Zheng; Zhang, Bing-Xiu; Liu, Cheng-Hai

2014-10-01

In the present study, a new method using near infrared spectroscopy combined with optical fiber sensing technology was applied to the analysis of hogwash oil in blended oil. The 50 samples were a blend of frying oil and "nine three" soybean oil according to a certain volume ratio. The near infrared transmission spectroscopies were collected and the quantitative analysis model of frying oil was established by partial least squares (PLS) and BP artificial neural network The coefficients of determina- tion of calibration sets were 0.908 and 0.934 respectively. The coefficients of determination of validation sets were 0.961 and 0.952, the root mean square error of calibrations (RMSEC) was 0.184 and 0.136, and the root mean square error of predictions (RMSEP) was all 0.111 6. They conform to the model application requirement. At the same time, frying oil and qualified edible oil were identified with the principal component analysis (PCA), and the accurate rate was 100%. The experiment proved that near infrared spectral technology not only can quickly and accurately identify hogwash oil, but also can quantitatively detect hog- wash oil. This method has a wide application prospect in the detection of oil.

Have oil and gas prices got separated?

International Nuclear Information System (INIS)

Erdős, Péter

2012-01-01

This paper applies vector error correction models that show that oil and natural gas prices decoupled around 2009. Before 2009, US and UK gas prices had a long-term equilibrium with crude prices to which gas prices always reverted after exogenous shocks. Both US and UK gas prices adjusted to the crude oil price individually, and departure from the equilibrium gas price on one continent resulted in a similar departure on the other. After an exogenous shock, the adjustment between US and UK gas prices took approximately 20 weeks on average, and the convergence was mediated mainly by crude oil with a necessary condition that arbitrage across the Atlantic was possible. After 2009, however, the UK gas price has remained integrated with oil price, but the US gas price decoupled from crude oil price and the European gas price, as the Atlantic arbitrage has halted. The oversupply from shale gas production has not been mitigated by North American export, as there has been no liquefying and export capacity. - Highlights: ► VEC models are applied to investigate the relationship between oil and natural gas prices. ► While natural gas prices in Europe and Asia react to oil price, US gas price decoupled from oil in 2009. ► Since 2009, the US gas price has decoupled from the European and Asian gas prices.

Treatment of emulsified oils by electrocoagulation: pulsed voltage applications.

Science.gov (United States)

Genc, Ayten; Bakirci, Busra

2015-01-01

The effect of pulsed voltage application on energy consumption during electrocoagulation was investigated. Three voltage profiles having the same arithmetic average with respect to time were applied to the electrodes. The specific energy consumption for these profiles were evaluated and analyzed together with oil removal efficiencies. The effects of applied voltages, electrode materials, electrode configurations, and pH on oil removal efficiency were determined. Electrocoagulation experiments were performed by using synthetic and real wastewater samples. The pulsed voltages saved energy during the electrocoagulation process. In continuous operation, energy saving was as high as 48%. Aluminum electrodes used for the treatment of emulsified oils resulted in higher oil removal efficiencies in comparison with stainless steel and iron electrodes. When the electrodes gap was less than 1 cm, higher oil removal efficiencies were obtained. The highest oil removal efficiencies were 95% and 35% for the batch and continuous operating modes, respectively.

Ecological effects research related to oil spills and oil spill countermeasures

International Nuclear Information System (INIS)

Aurand, D.

1992-01-01

The Marine Spill Response Corporation (MSRC) was created specifically to provide an improved response option for large marine oil spills in U.S. waters. As part of that capability, MSRC is committed to an extensive research and development program designed to improve the state-of-the-art for oil spill response. Within the mission, the goals of the Environmental Health Program are to ensure that ecological and human health effects of both oil and oil cleanup counter measures are well understood and that this information is made widely available for appropriate consideration in planning and implementing oil spill response efforts. This an applied program, and is intended to directly support the MSRC response mission. It does not include studies directly related to damage assessment, which is outside of the mission of MSRC. This paper focuses on the issues MSRC sees as critical in the area of ecological effects research, and addresses four topics: Why do we need to do more? What is it we hope to accomplish? What needs to be done? What is being planned or implemented?

Microtubule reorganization in tobacco BY-2 cells stably expressing GFP-MBD

Science.gov (United States)

Granger, C. L.; Cyr, R. J.

2000-01-01

Microtubule organization plays an important role in plant morphogenesis; however, little is known about how microtubule arrays transit from one organized state to another. The use of a genetically incorporated fluorescent marker would allow long-term observation of microtubule behavior in living cells. Here, we have characterized a Nicotiana tabacum L. cv. Bright Yellow 2 (BY-2) cell line that had been stably transformed with a gfp-mbd construct previously demonstrated to label microtubules (J. Marc et al., 1998, Plant Cell 10: 1927-1939). Fluorescence levels were low, but interphase and mitotic microtubule arrays, as well as the transitions between these arrays, could be observed in individual gfp-mbd-transformed cells. By comparing several attributes of transformed and untransformed cells it was concluded that the transgenic cells are not adversely affected by low-level expression of the transgene and that these cells will serve as a useful and accurate model system for observing microtubule reorganization in vivo. Indeed, some initial observations were made that are consistent with the involvement of motor proteins in the transition between the spindle and phragmoplast arrays. Our observations also support the role of the perinuclear region in nucleating microtubules at the end of cell division with a progressive shift of these microtubules and/or nucleating activity to the cortex to form the interphase cortical array.

Rapid analytical procedure for determination of mineral oils in edible oil by GC-FID.

Science.gov (United States)

Wrona, Magdalena; Pezo, Davinson; Nerin, Cristina

2013-12-15

A procedure for the determination of mineral oils in edible oil has been fully developed. The procedure consists of using a sulphuric acid-impregnated silica gel (SAISG) glass column to eliminate the fat matter. A chemical combustion of the fatty acids takes place, while the mineral oils are not affected by the sulphuric acid. The column is eluted with hexane using a vacuum pump and the final extract is concentrated and analysed by gas chromatography (GC) with flame ionisation detector (FID). The detection limit (LOD) and the quantification limit (LOQ) in hexane were 0.07 and 0.21 μg g(-1) respectively and the LOQ in vegetable oil was 1 μg g(-1). Only a few minutes were necessary for sample treatment to have a clean extract. The efficiency of the process, measured through the recoveries from spiked samples of edible oil was higher than 95%. The procedure has been applied to determine mineral oil in olive oil from the retailed market. Copyright © 2013 Elsevier Ltd. All rights reserved.

Combating desertification - fuel oil from jatropha plants in Africa: a systematic approach applied by a GTZ-supported project in Mali, West Africa

Energy Technology Data Exchange (ETDEWEB)

Henning, R K [Projet Pourghere, Deutsche Gesellschaft fuer technische Zusammenarbeit (GTZ), Bamako (Mali)

1995-12-01

The use of plant oil as an engine fuel has a long and eventful history, and technical developments have largely been completed. The economic conditions, however, do not yet suffice to produce a breakthrough for plant oil use as fuel in most industrialized and developing countries. The approach applied by a pilot project in Mali and described in this paper tries to overcome these economic drawbacks. The primary aim of the project is not the use of plant oil from Jatropha as a fuel per se, but rather to make that fuel use into an incentive that would activate a system combining ecologic, economic and income-generating effects, the latter specifically for women. These effects could materialize only if the non-edible oil of the jatropha plant can find an economically viable use. Since jatropha trees (Jatropha curcas L.) not only bear oil-rich seed, but can also be planted in the form of hedges to protect gardens and fields from foraging animals while warding off soil erosion, this would seem to be a case of positive correlation between energy production and agricultural production: the more energy that is produced by the hedgerows of jatropha, the more food production is strengthened. Of particular importance here is the recycling of the oil cake as organic fertilizer. The technologies used in the jatropha system are the well-known hand-driven or mechanically driven oil presses and with precombustion chambers diesel engines. While various makes, the latter are already available on the local market, the presses can be produced locally at affordable prices. The project`s activities focus, accordingly, on training and disseminating the relevant know-how. They do this by using local, often non-governmental institutions and by offering advice to farmers and rural communities interested in the jatropha system. The economic analysis using the UNIDO COMFAR III program shows very positive impacts if both direct and indirect effects are considered. Even in a completely non

A new paradigm for oil?

International Nuclear Information System (INIS)

Noel, P.

2004-09-01

The author takes stock on the dynamic of the oil system. He shows how the economic laws can be applied to the petroleum market and analyzes the effects of the prices evolution. The creeping oil shock of 2003-2004 has proven less disruptive than one may have anticipated. Commodity cycles on the one hand the shaky management of marginal supply by OPEC on the other hand, are very likely to create ample prices swings with little relations, if any, to the actual scarcity-or lack thereof-of oil resources. (A.L.B.)

Economic aspects of management of oil industry

International Nuclear Information System (INIS)

Purina, I.; Sipkovs, P.

1997-01-01

Oil industry is characterised by huge and long-term capital investments. This is one of the most specific features of the industry which has to be taken into account during the preparation of oil industry management framework by the state institutions. This article covers specific issues of cash flows and risks intrinsic in the oil industry projects as well as economic instruments to be applied. (author)

Oil prices, fiscal policy, and economic growth in oil-exporting countries

Science.gov (United States)

El-Anshasy, Amany A.

This dissertation argues that in oil-exporting countries fiscal policy could play an important role in transmitting the oil shocks to the economy and that the indirect effects of the changes in oil prices via the fiscal channel could be quite significant. The study comprises three distinct, yet related, essays. In the first essay, I try to study the fiscal policy response to the changes in oil prices and to their growing volatility. In a dynamic general equilibrium framework, a fiscal policy reaction function is derived and is empirically tested for a panel of 15 oil-exporters covering the period 1970--2000. After the link between oil price shocks and fiscal policy is established, the second essay tries to investigate the impact of the highly volatile oil prices on economic growth for the same sample, controlling for the fiscal channel. In both essays the study employs recent dynamic panel-data estimation techniques: System GMM. This approach has the potential advantages of minimizing the bias resulting from estimating dynamic panel models, exploiting the time series properties of the data, controlling for the unobserved country-specific effects, and correcting for any simultaneity bias. In the third essay, I focus on the case of Venezuela for the period 1950--2001. The recent developments in the cointegrating vector autoregression, CVAR technique is applied to provide a suitable framework for analyzing the short-run dynamics and the long-run relationships among oil prices, government revenues, government consumption, investment, and output.

India Edible Oil Consumption: A Censored Incomplete Demand Approach

OpenAIRE

Pan, Suwen; Mohanty, Samarendu; Welch, Mark

2008-01-01

A Censored Incomplete Demand System is applied to household expenditures for edible oil in India. The results show that edible peanut oil is still a luxury good in India, whereas expenditure elasticities for other edible oils are relatively low. The food habit, location, education of household heads, and other demographic variables have significant effects on the choice of edible oils.

Research on using oil herding surfactants to thicken oil slicks in pack ice for in situ burning

International Nuclear Information System (INIS)

Buist, I.; Morrison, J.

2005-01-01

The severe limitations of conventional containment and recovery systems for oil spills in pack ice have been demonstrated during skimmer tests conducted in the Alaskan Beaufort Sea. In-situ burning may be one of the few viable alternatives to quickly remove oil spilled in pack ice, but the slicks are often too thin, preventing effective ignition or burning. This study examined ways to thicken the slicks to the 2- to 5-mm range so that effective burns could be carried out. Specific chemical surface-active agents known as oil herders or oil collecting agents can be used to clear and contain oil slicks on water surfaces. Since these agents can spread quickly on water, only a small quantity is needed to clear thin films of oil from large areas of water. Applying a chemical herder around the periphery of spilled oil can contract the oil into a thicker slick. Two chemical products were developed and tested in the 1970s and 1980s: Shell Herder and Exxon OC-5 Oil Collector. However, they are no longer used because they were effective only in very calm conditions. Corexit EC9580 which exhibits similar slick herding abilities and which has a spreading pressure of 39.5 mN/m is still commercially available. This study tested formulations of herding agents for use in pack ice. Concerns regarding the potential toxicity risk of using these agents in pack ice were also addressed. The agents should not harm the environment because they have low toxicity and only very small quantities are used. Two series of tests conducted to assess the potential for herding agents to help ignite and effectively burn thin oil slicks in loose pack ice conditions. The agents proved to be effective on cold water and on thick slicks. The composition of the oil played an important role in determining potential efficiency. It was concluded that applying herders to thin oil slicks in pack ice shows considerable promise for thickening them for in-situ burning. 12 refs., 4 tabs., 17 figs

Thermal Cracking of Jatropha Oil with Hydrogen to Produce Bio-Fuel Oil

Directory of Open Access Journals (Sweden)

Yi-Yu Wang

2016-11-01

Full Text Available This study used thermal cracking with hydrogen (HTC to produce bio-fuel oil (BFO from jatropha oil (JO and to improve its quality. We conducted HTC with different hydrogen pressures (PH2; 0–2.07 MPa or 0–300 psig, retention times (tr; 40–780 min, and set temperatures (TC; 623–683 K. By applying HTC, the oil molecules can be hydrogenated and broken down into smaller molecules. The acid value (AV, iodine value, kinematic viscosity (KV, density, and heating value (HV of the BFO produced were measured and compared with the prevailing standards for oil to assess its suitability as a substitute for fossil fuels or biofuels. The results indicate that an increase in PH2 tends to increase the AV and KV while decreasing the HV of the BFO. The BFO yield (YBFO increases with PH2 and tr. The above properties decrease with increasing TC. Upon HTC at 0.69 MPa (100 psig H2 pressure, 60 min time, and 683 K temperature, the YBFO was found to be 86 wt%. The resulting BFO possesses simulated distillation characteristics superior to those of boat oil and heavy oil while being similar to those of diesel oil. The BFO contains 15.48% light naphtha, 35.73% heavy naphtha, 21.79% light gas oil, and 27% heavy gas oil and vacuum residue. These constituents can be further refined to produce gasoline, diesel, lubricants, and other fuel products.

Recovery of oil from underground drill sites

International Nuclear Information System (INIS)

Streeter, W.S.; Hutchinson, T.S.; Ameri, S.; Wasson, J.A.; Aminian, K.

1991-01-01

This paper reports that a significant quantity of oil is left in reservoirs after conventional oil recovery techniques have been applied. In West Virginia and Pennsylvania alone, this oil has been estimated at over 4.5 billion barrels (0.72 billion m 3 ). Conventional recovery methods are already being used when applicable. But a new recovery method is needed for use in reservoirs that have been abandoned. One alternative method for recovery of the residual oil is known as oil recovery from underground drill sites. This recovery technology is a combination of proven methods and equipment from the petroleum, mining, and civil construction industries. Underground oil recovery can be an economically viable method of producing oil. This has been shown in producing fields, field tests, and feasibility, studies. Faced with decreasing domestic oil production, the petroleum industry should give serious consideration to the use of oil recovery from underground drill sites as a safe, practical, and environmentally sensitive alternative method of producing oil from many reservoirs

Establishment of a novel immortalized human prostatic epithelial cell line stably expressing androgen receptor and its application for the functional screening of androgen receptor modulators

International Nuclear Information System (INIS)

Yu, Shan; Wang, Ming-Wei; Yao, Xiaoqiang; Chan, F.L.

2009-01-01

In this study, we developed a human prostatic epithelial cell line BPH-1-AR stably expressing AR by lentiviral transduction. Characterization by immunoblot and RT-PCR showed that AR was stably expressed in all representative BPH-1-AR clones. Androgen treatment induced a secretory differentiation phenotype in BPH-1-AR cells but suppressed their cell proliferation. Treatments with AR agonists induced transactivation of a transfected PSA-gene promoter reporter in BPH-1-AR cells, whereas this transactivation was suppressed by an AR antagonist flutamide, indicating that the transduced AR in BPH-1-AR cells was functional. Finally, we utilized BPH-1-AR cells to evaluate the androgenic activities and growth effects of five newly developed non-steroidal compounds. Results showed that these compounds showed androgenic activities and growth-inhibitory effects on BPH-1-AR cells. Our results showed that BPH-1-AR cell line would be a valuable in vitro model for the study of androgen-regulated processes in prostatic epithelial cells and identification of compounds with AR-modulating activities.

Characterization of Streptomyces spp. isolated from the rhizosphere of oil palm and evaluation of their ability to suppress basal stem rot disease in oil palm seedlings when applied as powder formulations in a glasshouse trial.

Science.gov (United States)

Shariffah-Muzaimah, S A; Idris, A S; Madihah, A Z; Dzolkhifli, O; Kamaruzzaman, S; Maizatul-Suriza, M

2017-12-18

Ganoderma boninense, the main causal agent of oil palm (Elaeis guineensis) basal stem rot (BSR), severely reduces oil palm yields around the world. To reduce reliance on fungicide applications to control BSR, we are investigating the efficacy of alternative control methods, such as the application of biological control agents. In this study, we used four Streptomyces-like actinomycetes (isolates AGA43, AGA48, AGA347 and AGA506) that had been isolated from the oil palm rhizosphere and screened for antagonism towards G. boninense in a previous study. The aim of this study was to characterize these four isolates and then to assess their ability to suppress BSR in oil palm seedlings when applied individually to the soil in a vermiculite powder formulation. Analysis of partial 16S rRNA gene sequences (512 bp) revealed that the isolates exhibited a very high level of sequence similarity (> 98%) with GenBank reference sequences. Isolates AGA347 and AGA506 showed 99% similarity with Streptomyces hygroscopicus subsp. hygroscopicus and Streptomyces ahygroscopicus, respectively. Isolates AGA43 and AGA48 also belonged to the Streptomyces genus. The most effective formulation, AGA347, reduced BSR in seedlings by 73.1%. Formulations using the known antifungal producer Streptomyces noursei, AGA043, AGA048 or AGA506 reduced BSR by 47.4, 30.1, 54.8 and 44.1%, respectively. This glasshouse trial indicates that these Streptomyces spp. show promise as potential biological control agents against Ganoderma in oil palm. Further investigations are needed to determine the mechanism of antagonism and to increase the shelf life of Streptomyces formulations.

Biodegradability of northern crude oil

Energy Technology Data Exchange (ETDEWEB)

Cook, F D; Westlake, D W.S.

1976-01-01

Field studies on the microbiological degradation of crude oils encompassed the placing of oil-soaked plots in two areas in the Northwest Territories and Alberta. Replicate plots received amendments of fertilizer, oil-utilizing bacteria, fertilizer plus bacteria or were untreated except for the oil. Changes in microbial numbers and chemical composition of recovered oil were determined periodically. The initial stimulatory effect on bacterial numbers brought about by the addition of fertilizers to oil-soaked plots diminished two years after the application to a point where the differences were no longer significant. Experiments carried out in the Norman Wells area to determine the effect of the amount of fertilizer applied on oil degradation have yielded inconclusive results. The data suggest that at least 2.7 kg of urea-phosphate fertilizer per kl of oil is required to maintain a reasonable oil degradation rate. Preliminary studies on the use of fertilizer coated with chemicals to increase its hydrophobic character indicate that they could be useful in treating wet-land oil spills. Soils from the McKenzie River drainage basin indicate that bacteria are present which can use oil under mesophilic conditions. However, the ability to use the same oil under psychrophilic conditions is more restricted. At least one bacterial species from each mixed population studied was capable of bringing about chemical changes in oil similar to those observed for the original mixed culture. The potential hazards and uses of the seeding of oil spills is discussed relative to the environmental conditions found in the northern part of Canada. 35 refs., 2 figs., 15 tabs.

Using Polymer Alternating Gas to Enhance Oil Recovery in Heavy Oil

Science.gov (United States)

Yang, Yongzhi; Li, Weirong; Zhou, Tiyao; Dong, Zhenzhen

2018-02-01

CO2 has been used to recover oil for more than 40 years. Currently, about 43% of EOR production in U.S. is from CO2 flooding. CO2 flooding is a well-established EOR technique, but its density and viscosity nature are challenges for CO2 projects. Low density (0.5 to 0.8 g/cm3) causes gas to rise upward in reservoirs and bypass many lower portions of the reservoir. Low viscosity (0.02 to 0.08 cp) leads to poor volumetric sweep efficiency. So water-alternating-gas (WAG) method was used to control the mobility of CO2 and improve sweep efficiency. However, WAG process has some other problems in heavy oil reservoir, such as poor mobility ratio and gravity overriding. To examine the applicability of carbon dioxide to recover viscous oil from highly heterogeneous reservoirs, this study suggests a new EOR method--polymer-alternating gas (PAG) process. The process involves a combination of polymer flooding and CO2 injection. To confirm the effectiveness of PAG process in heavy oils, a reservoir model from Liaohe Oilfield is used to compare the technical and economic performance among PAG, WAG and polymer flooding. Simulation results show that PAG method would increase oil recovery over 10% compared with other EOR methods and PAG would be economically success based on assumption in this study. This study is the first to apply PAG to enhance oil recovery in heavy oil reservoir with highly heterogeneous. Besides, this paper provides detailed discussions and comparison about PAG with other EOR methods in this heavy oil reservoir.

Satellite and airborne oil spill remote sensing: state of the art and application to the BP Deepwater Horizon oil spill

Energy Technology Data Exchange (ETDEWEB)

Leifer, Ira [University of California (United States); Clark, Roger; Swayze, Gregg [US Geology Survey (United States); Jones, Cathleen [California Institute of Technology (United States); Svejkovsky, Jan [Ocean Imaging Corporation (United States)

2011-07-01

This study stresses the value of using satellite technology in quantifying oil seepage impact, and how it can be applied to the case of Horizon oil spill. The purpose of the study is to clarify the remote sensing process as it applies to oil spills, and how testing resources should be properly allocated so as to come up with the optimal response strategy. Many parameters were involved in this research, of which the most important were the environmental factors, the active and passive remote sensing measures, satellite imagery and imaging spectroscopy, and oil thickness measurements using thermal infrared and laser-induced fluorescence. These parameters were later used to quantify the spills in the impacted regions. Results showed that remote sensing would always be accompanied by certain errors, however, in the case of the Horizon spill, the infrared approach proved to be a convenient and a reliable approach for impact analysis process. The study also put emphasis on the importance of oil spatial patterns in validating the reliability of a test procedure.

Satellite and airborne oil spill remote sensing: state of the art and application to the BP Deepwater Horizon oil spill

International Nuclear Information System (INIS)

Leifer, Ira; Clark, Roger; Swayze, Gregg; Jones, Cathleen; Svejkovsky, Jan

2011-01-01

This study stresses the value of using satellite technology in quantifying oil seepage impact, and how it can be applied to the case of Horizon oil spill. The purpose of the study is to clarify the remote sensing process as it applies to oil spills, and how testing resources should be properly allocated so as to come up with the optimal response strategy. Many parameters were involved in this research, of which the most important were the environmental factors, the active and passive remote sensing measures, satellite imagery and imaging spectroscopy, and oil thickness measurements using thermal infrared and laser-induced fluorescence. These parameters were later used to quantify the spills in the impacted regions. Results showed that remote sensing would always be accompanied by certain errors, however, in the case of the Horizon spill, the infrared approach proved to be a convenient and a reliable approach for impact analysis process. The study also put emphasis on the importance of oil spatial patterns in validating the reliability of a test procedure.

Bohai and Yellow Sea Oil Spill Prediction System and Its Application to Huangdao ‘11.22’ Oil Spill Incident

Science.gov (United States)

Li, Huan; Li, Yan; Li, Cheng; Li, Wenshan; Wang, Guosong; Zhang, Song

2017-08-01

Marine oil spill has deep negative effect on both marine ecosystem and human activities. In recent years, due to China’s high-speed economic development, the demand for crude oil is increasing year by year in China, and leading to the high risk of marine oil spill. Therefore, it is necessary that promoting emergency response on marine oil spill in China and improving oil spill prediction techniques. In this study, based on oil spill model and GIS platform, we have developed the Bohai and Yellow sea oil spill prediction system. Combining with high-resolution meteorological and oceanographic forecast results, the system was applied to predict the drift and diffusion process of Huangdao ‘11.22’ oil spill incident. Although the prediction can’t be validated by some SAR images due to the lack of satellite observations, it still provided effective and referable oil spill behavior information to Maritime Safety Administration.

Electrocapillary Phenomena at Edible Oil/Saline Interfaces.

Science.gov (United States)

Nishimura, Satoshi; Ohzono, Takuya; Shoji, Kohei; Yagihara, Shin; Hayashi, Masafumi; Tanaka, Hisao

2017-03-01

Interfacial tension between edible oil and saline was measured under applied electric fields to understand the electrocapillary phenomena at the edible oil/saline interfaces. The electric responses of saline droplets in edible oil were also observed microscopically to examine the relationship between the electrocapillary phenomena and interfacial polarization. When sodium oleate (SO) was added to edible oil (SO-oil), the interfacial tension between SO-oil and saline decreased. However, no decrease was observed for additive-free oil or oleic acid (OA)-added oil (OA-oil). Microscopic observations suggested that the magnitude of interfacial polarization increased in the order of additive-free oil oil oil. The difference in electrocapillary phenomena between OA- and SO-oils was closely related to the polarization magnitude. In the case of SO-oil, the decrease in interfacial tension was remarkably larger for saline (pH 5.4~5.6) than that for phosphate-buffered saline (PBS, pH 7.2~7.4). However, no difference was observed between the electric responses of PBS and saline droplets in SO-oil. The difference in electrocapillary phenomena for PBS and saline could not be simply explained in terms of polarization magnitude. The ratio of ionized and non-ionized OA at the interfaces changed with the saline pH, possibly leading to the above difference.

Source identification of beached oil at Al Zubarah, Northwestern Qatar

DEFF Research Database (Denmark)

Al-Kaabi, Nasser S.; Kristensen, Mette; Zouari, Nabil

2017-01-01

compounds for these spill samples were compared to those of more than 250 crude oils from around the world applying the CHEMSIC method (chemometric analysis of selected ion chromatograms). The weathering degree varied significantly between samples, and relatively unweathered oil from the Gulf War oil spill...

Oil sands to the rescue: oil sand microbial communities can degrade recalcitrant alkyl phenyl alkanoic acids

Energy Technology Data Exchange (ETDEWEB)

Whitby, Corinne [University of Essex (Canada)], email: cwhitby@essex.ac.uk

2011-07-01

Almost half of all global oil reserves are found as biodegraded heavy oils found in vast tar sand deposits located in North and South America and these account for 47% of Canadian oil production. Oil sand extraction generates large amounts of toxic waste water, known as oil sand process waters (OSPW), that are stored in large tailing ponds that contain toxic compounds like naphthenic acids (NAs). The presence of NAs creates problems like toxicity, corrosion, and the formation of calcium napthenate deposits which block pipelines and other infrastructure and need to be removed. This paper presents oil sand microbial communities that can degrade these NAs. The approach is to apply new aliphatic and aromatic NAs as substrates to supplement and identify NA degrading microbes and also to identify the metabolites produced and explain NA degradation pathways and the functional genes involved. The chemistry and the processes involved are explained. From the results, it is suggested that pure cultures of P. putida KT2440 be used against NAs.

Waste minimization concepts applied to oil spill response or (integrating the Pollution Prevention Act of 1990 with the Oil Pollution Act of 1990)

International Nuclear Information System (INIS)

Ferriere, D.V.

1993-01-01

As of July 23, 1993 the National Contingency Plan (NCP) for oil spills and hazardous substance releases (40CFR300) is being revised to comply with Oil Pollution Act 1990 (OPA '90) requirements. An important OPA '90 development is the creation of localized groups to write Area Contingency Plans (ACPs). During the ACP process many political, economical, and environmental issues will be addressed by representatives from several local, county, state, federal agencies and industry. Some of the difficulty decision makers must face is weighing environmental tradeoffs considering socio-economic aspects and determining what is the most effective ecologically sensible/environmental protection oil spill response strategy. Ideally, the NCP is designed as a democratic process providing a voice to all effected parties on how to best protect the environment, natural resources, and commercial resources. However, practice has shown successful emergency response is best handled when a single focal point of command, commonly referred to as incident command, has an agreed upon response agenda. The following will address the need for decision makers and contingency planners to at least address waste minimization principles, if not make it their primary focus, when developing and executing the oil spill response plan

What Is the Best Strategy for Enhancing the Effects of Topically Applied Ozonated Oils in Cutaneous Infections?

Directory of Open Access Journals (Sweden)

I. Zanardi

2013-01-01

Full Text Available Owing to diabetes, atherosclerosis, and ageing, there are several million patients undergoing skin lesions degenerated into infected ulcers with very little tendency to heal and implying a huge socioeconomical cost. Previous medical experience has shown that the daily application of ozonated oil eliminates the infection and promotes a rapid healing. The purpose of the study is the optimization of the antimicrobial effect of ozonated oils by testing in vitro four bacterial species and one yeast without or in the presence of different amounts of human serum. The results obtained suggest that a gentle and continuous removal of debris and exudate is an essential condition for the potent bactericidal effect of ozonated oils. In fact, even small amounts of human serum inactivate ozone derivatives and protect bacteria. The application of ozonated oil preparations is very promising in a variety of skin and mucosal infections. Moreover, ozonated oils are far less expensive than antibiotic preparations.

Effects of Microwave Radiation on Oil Recovery

Science.gov (United States)

Esmaeili, Abdollah

2011-12-01

A variety of oil recovery methods have been developed and applied to mature and depleted reservoirs in order to improve the efficiency. Microwave radiation oil recovery method is a relatively new method and has been of great interest in the recent years. Crude oil is typically co-mingled with suspended solids and water. To increase oil recovery, it is necessary to remove these components. The separation of oil from water and solids using gravitational settling methods is typically incomplete. Oil-in-water and oil-water-solid emulsions can be demulsified and separated into their individual layers by microwave radiation. The data also show that microwave separation is faster than gravity separation and can be faster than conventional heating at many conditions. After separation of emulsion into water and oil layers, water can be discharged and oil is collected. High-frequency microwave recycling process can recover oil and gases from oil shale, residual oil, drill cuttings, tar sands oil, contaminated dredge/sediments, tires and plastics with significantly greater yields and lower costs than are available utilizing existing known technologies. This process is environmentally friendly, fuel-generating recycler to reduce waste, cut emissions, and save energy. This paper presents a critical review of Microwave radiation method for oil recovery.

Increased Oil Recovery from Mature Oil Fields Using Gelled Polymer Treatments

Energy Technology Data Exchange (ETDEWEB)

Willhite, G.P.; Green, D.W.; McCool, S.

2001-03-28

Gelled polymer treatments were applied to oil reservoirs to increase oil production and to reduce water production by altering the fluid movement within the reservoir. This report is aimed at reducing barriers to the widespread use of these treatments by developing methods to predict gel behavior during placement in matrix rock and fractures, determining the persistence of permeability reduction after gel placement, and by developing methods to design production well treatments to control water production. Procedures were developed to determine the weight-average molecular weight and average size of polyacrylamide samples in aqueous solutions. Sample preparation techniques were key to achieving reproducible results.

Principles of heavy oil recovery

Energy Technology Data Exchange (ETDEWEB)

Szasz, S.E.; Thomas, G.W.

1965-10-01

Rising exploration costs have prompted greater interest in the large known deposits of heavy oil in North America. Because of high oil viscosities in such reservoirs, recoveries are poor, fluid drives are inefficient and production rates are uneconomical. Viscosity reduction can best be accomplished by heating the reservoir. The basic aspects of reservoir heating are reviewed and those processes which are of practical importance in heavy oil reservoirs are discussed. Wellbore heating frequently can be applied to heavy oil reservoirs to increase production rates. In hot waterflooding, the water requirements are much higher than an ordinary waterflood. Steam floods are more attractive, but operating costs are generally high. Conduction heating processes appear most promising. Among these is included the cyclic steam-soak process. A simple method is presented for estimating the performance from the first cycle of steam injection into the formation, assuming gravity as the only driving energy. An example calculation for a typical heavy oil reservoir is given. (26 refs.)

A program approach for site safety at oil spills

International Nuclear Information System (INIS)

Whipple, F.L.; Glenn, S.P.; Ocken, J.J.; Ott, G.L.

1993-01-01

When OSHA developed the hazardous waste operations (Hazwoper) regulations (29 CFR 1910.120) members of the response community envisioned a separation of oil and open-quotes hazmatclose quotes response operations. Organizations that deal with oil spills have had difficulty applying Hazwoper regulations to oil spill operations. This hinders meaningful implementation of the standard for their personnel. We should approach oil spills with the same degree of caution that is applied to hazmat response. Training frequently does not address the safety of oil spill response operations. Site-specific safety and health plans often are neglected or omitted. Certain oils expose workers to carcinogens, as well as chronic and acute hazards. Significant physical hazards are most important. In responding to oil spills, the hazards must be addressed. It is the authors' contention that a need exists for safety program at oil spill sites. Gone are the days of labor pool hires cleaning up spills in jeans and sneakers. The key to meaningful programs for oil spills requires application of controls focused on relevant safety risks rather than minimal chemical exposure hazards. Working with concerned reviewers from other agencies and organizations, the authors have developed a general safety and health program for oil spill response. It is intended to serve as the basis for organizations to customize their own written safety and health program (required by OSHA). It also provides a separate generic site safety plan for emergency phase oil spill operations (check-list) and long term post-emergency phase operations

SOVENT BASED ENHANCED OIL RECOVERY FOR IN-SITU UPGRADING OF HEAVY OIL SANDS

Energy Technology Data Exchange (ETDEWEB)

Munroe, Norman

2009-01-30

With the depletion of conventional crude oil reserves in the world, heavy oil and bitumen resources have great potential to meet the future demand for petroleum products. However, oil recovery from heavy oil and bitumen reservoirs is much more difficult than that from conventional oil reservoirs. This is mainly because heavy oil or bitumen is partially or completely immobile under reservoir conditions due to its extremely high viscosity, which creates special production challenges. In order to overcome these challenges significant efforts were devoted by Applied Research Center (ARC) at Florida International University and The Center for Energy Economics (CEE) at the University of Texas. A simplified model was developed to assess the density of the upgraded crude depending on the ratio of solvent mass to crude oil mass, temperature, pressure and the properties of the crude oil. The simplified model incorporated the interaction dynamics into a homogeneous, porous heavy oil reservoir to simulate the dispersion and concentration of injected CO2. The model also incorporated the characteristic of a highly varying CO2 density near the critical point. Since the major challenge in heavy oil recovery is its high viscosity, most researchers have focused their investigations on this parameter in the laboratory as well as in the field resulting in disparaging results. This was attributed to oil being a complex poly-disperse blend of light and heavy paraffins, aromatics, resins and asphaltenes, which have diverse behaviors at reservoir temperature and pressures. The situation is exacerbated by a dearth of experimental data on gas diffusion coefficients in heavy oils due to the tedious nature of diffusivity measurements. Ultimately, the viscosity and thus oil recovery is regulated by pressure and its effect on the diffusion coefficient and oil swelling factors. The generation of a new phase within the crude and the differences in mobility between the new crude matrix and the

Process design for isolation of soybean oil bodies by applying the product-driven process synthesis methodology

NARCIS (Netherlands)

Zderic, A.; Taraksci, T.; Hooshyar, N.; Zondervan, E.; Meuldijk, J.

2014-01-01

The present work describes the product driven process synthesis (PDPS) methodology for the conceptual design of extraction of intact oil bodies from soybeans. First, in this approach consumer needs are taken into account and based on these needs application of the final product (oil bodies) is

Efficacy of fipronil aerially applied in oil adjuvants and drift retardants against boll weevils, Anthonomus Grandis Boheman (Coleoptera:Curculionidae)

Science.gov (United States)

Joseph E. Mulrooney

2002-01-01

Results of aerial application tests in the field and insecticide transfer tests in the laboratory showed that cottonseed oil was the most effective oil adjuvant to use with fipronil for controlling boll weevils under field conditions and for transferring fipronil from cotton leaf surfaces to boll weevils. The mineral oil and mineral oil + drift retardant more...

Extractive oxidative desulfurization of model oil/crude oil using KSF montmorillonite-supported 12-tungstophosphoric acid

Directory of Open Access Journals (Sweden)

Ezzat Rafiee

2016-10-01

Full Text Available Abstract 12-Tungstophosphoric acid (PW supported on KSF montmorillonite, PW/KSF, was used as catalyst for deep oxidative desulfurization (ODS of mixed thiophenic compounds in model oil and crude oil under mild conditions using hydrogen peroxide (H2O2 as an oxidizing agent. A one-factor-at-a-time method was applied for optimizing the parameters such as temperature, reaction time, amount of catalyst, type of extractant and oxidant-to-sulfur compounds (S-compounds molar ratio. The corresponding products can be easily removed from the model oil by using ethanol as the best extractant. The results showed high catalytic activity of PW/KSF in the oxidative removal of dibenzothiophene (DBT and mixed thiophenic model oil under atmospheric pressure at 75 °C in a biphasic system. To investigate the oxidation and adsorption effects of crude oil composition on ODS, the effects of cyclohexene, 1,7-octadiene and o-xylene with different concentrations were studied.

Insecticidal activity of some citrus oils against culex quinquefasciatus

International Nuclear Information System (INIS)

Saeed, H. M. A.

2009-01-01

The present study deals with the larvicidal potency of peel oils of grapefruit (Citrus paradise), sweet orange (Citrus sinensis) and lime (Citrus aurantifolia) on 4''th instar larvae of the mosquito, Culex quinquefasciatus. Orange oil was the most effective followed by grapefruit oil and then lime oil. The toxicity of the oils applied to the 4''th instar larval stage was extended to pupal and adult stages. All oils produced deleterious effects on fecundity of survivors of sublethal doses. By the aid of chemical analysis of oils, the active compound was found to be limonene, a monoterpene compound. The percentages limonene were 97.15%, 92.46% and 32.29% for orange, grapefruit and lime respectively.(Author)

Method of Determining the Filtration Properties of oil-Bearing Crops in the Process of Their Pressing by the Example of Rape-oil Extrusion

Science.gov (United States)

Slavnov, E. V.; Petrov, I. A.

2014-07-01

A method of determining the change in the fi ltration properties of oil-bearing crops in the process of their pressing by repeated dynamic loading is proposed. The use of this method is demonstrated by the example of rape-oil extrusion. It was established that the change in the mass concentration of the oil in a rape mix from 0.45 to 0.23 leads to a decrease in the permeability of the mix by 101.5-102 times depending on the pressure applied to it. It is shown that the dependence of the permeability of this mix on the pressure applied to it is nonmonotone in character.

Mining and oil. Oil shale's contribution to future oil supply; Bergbau und Oel. Der Beitrag des Oelschiefers zur Oelversorgung

Energy Technology Data Exchange (ETDEWEB)

Linden, Eike von der [Linden Advisory, Dreieich (Germany)

2012-05-15

Crude oil contributes in Germany and globally approximately one third to the consumption of primary energies and actually is and in the foreseeable future will be the most important energy source. Recently shale oil as an unconventional oil has gained attention in public discussions. Depending on temperatures oil shale contains either already matured fluid shale oil or immature waxy kerogen. For determination of kerogen containing oil shale and shale oil common definitions for fluid hydrocarbons will be presented. Fluid hydrocarbons (molecular chains > C{sub 5}H{sub 12}) originate from animal substance which had been settled millions of years in sediments on sea- or lakebeds under anaerobic conditions. High pressure and high temperatures effect conversion to hydrocarbons. With sufficient permeability the liquid hydrocarbons migrate from the sediment as the source rock and get assembled in porous rocks under the cover of an impermeable rock strata, in so called entrapment structures. In case there is no impermeable rock strate the hydrocarbons will diffuse into the atmosphere. The hydrocarbons in entrapment structures are called conventional oil and are extracted by drilling wells. The extractable oil as part of the oil in place depends on the viscosity of the oil, the permeability of the host rock and applied exploitation methods which can affect pressure, viscosity and permeability. The exploitation achieves 30 to 50% of the oil in place. When the source rock consisting of strata hundreds of meters thick is not sufficiently permeable the matured hydrocarbons remain at its place of origination. These hydrocarbons are called shale oil and belong to the unconventional oil resources. For exploitation of shale oil by wells the source rock must be treated by intensive energy input, amongst others, by fracking which creates artificial permeability and by pressure which affects migration of the hydrocarbons to the well. The exploitation methods for shale oil do not

Discussion of the feasibility of air injection for enhanced oil recovery in shale oil reservoirs

Directory of Open Access Journals (Sweden)

Hu Jia

2017-06-01

Full Text Available Air injection in light oil reservoirs has received considerable attention as an effective, improved oil recovery process, based primarily on the success of several projects within the Williston Basin in the United States. The main mechanism of air injection is the oxidation behavior between oxygen and crude oil in the reservoir. Air injection is a good option because of its wide availability and low cost. Whether air injection can be applied to shale is an interesting topic from both economic and technical perspectives. This paper initiates a comprehensive discussion on the feasibility and potential of air injection in shale oil reservoirs based on state-of-the-art literature review. Favorable and unfavorable effects of using air injection are discussed in an analogy analysis on geology, reservoir features, temperature, pressure, and petrophysical, mineral and crude oil properties of shale oil reservoirs. The available data comparison of the historically successful air injection projects with typical shale oil reservoirs in the U.S. is summarized in this paper. Some operation methods to improve air injection performance are recommended. This paper provides an avenue for us to make use of many of the favorable conditions of shale oil reservoirs for implementing air injection, or air huff ‘n’ puff injection, and the low cost of air has the potential to improve oil recovery in shale oil reservoirs. This analysis may stimulate further investigation.

A Comparison of Vibration and Oil Debris Gear Damage Detection Methods Applied to Pitting Damage

Science.gov (United States)

Dempsey, Paula J.

2000-01-01

Helicopter Health Usage Monitoring Systems (HUMS) must provide reliable, real-time performance monitoring of helicopter operating parameters to prevent damage of flight critical components. Helicopter transmission diagnostics are an important part of a helicopter HUMS. In order to improve the reliability of transmission diagnostics, many researchers propose combining two technologies, vibration and oil monitoring, using data fusion and intelligent systems. Some benefits of combining multiple sensors to make decisions include improved detection capabilities and increased probability the event is detected. However, if the sensors are inaccurate, or the features extracted from the sensors are poor predictors of transmission health, integration of these sensors will decrease the accuracy of damage prediction. For this reason, one must verify the individual integrity of vibration and oil analysis methods prior to integrating the two technologies. This research focuses on comparing the capability of two vibration algorithms, FM4 and NA4, and a commercially available on-line oil debris monitor to detect pitting damage on spur gears in the NASA Glenn Research Center Spur Gear Fatigue Test Rig. Results from this research indicate that the rate of change of debris mass measured by the oil debris monitor is comparable to the vibration algorithms in detecting gear pitting damage.

Partial Discharge Phase Distribution Of Palm Oil As Insulating Liquid

Directory of Open Access Journals (Sweden)

Abdul Rajab

2011-04-01

Full Text Available Due to the low biodegradability level of mineral oil and its susceptibility to the fire, palm oil was proposed as alternative insulating liquid. This paper discusses partial discharge (PD in palm oil under sinusoidal voltages and the comparison with mineral oil. PD was generated using a needle-plane electrode configuration which is enable enhancing electric field at the needle tip. PD pulses were detected using RC detector and they were measured using a Computer-based partial discharge measurement system. The results showed that PD activities in both oils are similar. The PD was initiated at the negative polarity of applied voltage. The discharges took place in both polarity’s of applied voltage with PD number was higher at negative one. Several discharges phenomena showed the presence of space charge which changed electric field and governed PD activities besides the main field introduced by voltage application.

Transesterification of jojoba oil, sunflower oil, neem oil, rocket seed oil and linseed oil by tin catalysts

International Nuclear Information System (INIS)

Shah, Mazloom; Tariq, Muhammad; Ali, Saqib; Guo, Qing-Xiang; Fu, Yao

2014-01-01

The methanolysis of jojoba oil has been studied in the presence of tin powder, dibutyltin diacetate (C 4 H 9 ) 2 Sn(OOCCH 3 ) 2 , dioctyltin diacetate (C 8 H 17 ) 2 Sn(OOCCH 3 ) 2 , dibutyltin oxide (C 4 H 9 ) 2 SnO, dioctyltin oxide (C 8 H 17 ) 2 SnO, diphenyltin oxide (C 6 H 5 ) 2 SnO, dibutyltin chloride dihydroxide (C 4 H 9 ) 2 Sn(OH) 2 Cl, butyltinhydroxide hydrate (C 4 H 9 )Sn(=O)OH.xH 2 O, Ni nanoparticles and Pd nanoparticles act as catalysts. Among these, 1 weight % of dibutyltin diacetate shows the maximum conversion. Then, methanolysis of sunflower oil, neem oil, rocket seed oil and linseed oil into methyl esters studied in the presence of 1% dibutyltin diacetate as a catalyst and was compared their percentage conversions. The experimental yield for the conversion of jojoba oil, sunflower oil, neem oil, rocket seed oil and linseed oil into biodiesel was found to be 71%, 51%, 50.78%, 40.90% and 39.66%, respectively. The experimental yield of the conversion of jojoba oil into methyl esters was found to be increased up to 96% by increasing reaction time, without emulsion formation. The synthesis of jojoba seed oil biodiesel (JSOB), soybean oil biodiesel (SOB), neem oil biodiesel (NOB), rocket seed oil biodiesel (RSOB) and linseed oil biodiesel (LSOB) was confirmed by NMR ( 1 H and 13 C) and FT-IR analyses of biodiesel. - Highlights: • Transesterification of jojoba oil into biodiesel by tin and nano catalysts. • 1 weight % dibutyltin diacetate showed highest yield at 60 °C. • Catalytic conversion comparison of five oils using dibutyltin diacetate • The experimental yield of the conversion of jojoba oil increased with time. • FT-IR and NMR ( 1 H and 13 C) characterization

Optimisation of Oil Spill Dispersants on Weathered Oils. A New Approach Using Experimental Design and Multivariate Data Analysis

Energy Technology Data Exchange (ETDEWEB)

Brandvik, Per Johan

1997-12-31

This thesis describes how laboratory experiments combined with numerical modelling were used to predict weathering of an oil slick at different environmental conditions (temperature, wind etc.). It also applies laboratory test methods to screen dispersant effectiveness under different temperatures and salinities. A new approach is developed for dispersant optimization based on statistical design and multivariate analysis; this resulted in a new dispersant with low toxicity and high effectiveness on a broad selection of oil types. The thesis illustrates the potential of dispersant used as an operational response method on oil spills by discussing three different oil spill scenarios and compares the effect of using dispersants to using mechanical recovery and to doing nothing. Some recommendations that may increase the effectiveness of the Norwegian oil spill contingency are also given. 172 refs., 65 figs., 9 tabs.

APPLIED PHYTO-REMEDIATION TECHNIQUES USING HALOPHYTES FOR OIL AND BRINE SPILL SCARS

Energy Technology Data Exchange (ETDEWEB)

M.L. Korphage; Bruce G. Langhus; Scott Campbell

2003-03-01

Produced salt water from historical oil and gas production was often managed with inadequate care and unfortunate consequences. In Kansas, the production practices in the 1930's and 1940's--before statewide anti-pollution laws--were such that fluids were often produced to surface impoundments where the oil would segregate from the salt water. The oil was pumped off the pits and the salt water was able to infiltrate into the subsurface soil zones and underlying bedrock. Over the years, oil producing practices were changed so that segregation of fluids was accomplished in steel tanks and salt water was isolated from the natural environment. But before that could happen, significant areas of the state were scarred by salt water. These areas are now in need of economical remediation. Remediation of salt scarred land can be facilitated with soil amendments, land management, and selection of appropriate salt tolerant plants. Current research on the salt scars around the old Leon Waterflood, in Butler County, Kansas show the relative efficiency of remediation options. Based upon these research findings, it is possible to recommend cost efficient remediation techniques for slight, medium, and heavy salt water damaged soil. Slight salt damage includes soils with Electrical Conductivity (EC) values of 4.0 mS/cm or less. Operators can treat these soils with sufficient amounts of gypsum, install irrigation systems, and till the soil. Appropriate plants can be introduced via transplants or seeded. Medium salt damage includes soils with EC values between 4.0 and 16 mS/cm. Operators will add amendments of gypsum, till the soil, and arrange for irrigation. Some particularly salt tolerant plants can be added but most planting ought to be reserved until the second season of remediation. Severe salt damage includes soil with EC values in excess of 16 mS/cm. Operators will add at least part of the gypsum required, till the soil, and arrange for irrigation. The following

Forecasting ability of the investor sentiment endurance index: The case of oil service stock returns and crude oil prices

International Nuclear Information System (INIS)

He, Ling T.; Casey, K.M.

2015-01-01

Using a binomial probability distribution model this paper creates an endurance index of oil service investor sentiment. The index reflects the probability of the high or low stock price being the close price for the PHLX Oil Service Sector Index. Results of this study reveal the substantial forecasting ability of the sentiment endurance index. Monthly and quarterly rolling forecasts of returns of oil service stocks have an overall accuracy as high as 52% to 57%. In addition, the index shows decent forecasting ability on changes in crude oil prices, especially, WTI prices. The accuracy of 6-quarter rolling forecasts is 55%. The sentiment endurance index, along with the procedure of true forecasting and accuracy ratio, applied in this study provides investors and analysts of oil service sector stocks and crude oil prices as well as energy policy-makers with effective analytical tools

Asporin stably expressed in the surface layer of mandibular condylar cartilage and augmented in the deeper layer with age.

Science.gov (United States)

Miyamoto, Yutaka; Kanzaki, Hiroyuki; Wada, Satoshi; Tsuruoka, Sari; Itohiya, Kanako; Kumagai, Kenichi; Hamada, Yoshiki; Nakamura, Yoshiki

2017-12-01

Mandibular condylar cartilage (MCC) exhibits dual roles both articular cartilage and growth center. Of many growth factors, TGF-β has been implicated in the growth of articular cartilage including MCC. Recently, Asporin, decoy to TGF-β, was discovered and it blocks TGF-β signaling. Asporin is expressed in a variety of tissues including osteoarthritic articular cartilage, though there was no report of Asporin expression in MCC. In the present study, we investigated the temporal and spatial expression of Asporin in MCC. Gene expression profile of MCC and epiphyseal cartilage in tibia of 5 weeks old ICR mice were firstly compared with microarray analysis using the laser capture microdissected samples. Variance of gene expression was further confirmed by real-time RT-PCR and immunohistochemical staining at 1,3,10, and 20 weeks old. TGF-β and its signaling molecule, phosphorylated Smad-2/3 (p-Smad2/3), were also examined by immunohistochemical staining. Microarray analysis revealed that Asporin was highly expressed in MCC. Real-time RT-PCR analysis confirmed that the fibrous layer of MCC exhibited stable higher Asporin expression at any time points as compared to epiphyseal cartilage. This was also observed in immunohistochemical staining. Deeper layer in MCC augmented Asporin expression with age. Whereas, TGF-β was stably highly observed in the layer. The fibrous layer of MCC exhibited weak staining of p-Smad2/3, though the proliferating layer of MCC was strongly stained as compared to epiphyseal cartilage of tibia at early time point. Consistent with the increase of Asporin expression in the deeper layer of MCC, the intensity of p-Smad-2/3 staining was decreased with age. In conclusion, we discovered that Asporin was stably expressed at the fibrous layer of MCC, which makes it possible to manage both articular cartilage and growth center at the same time.

Report of the work-group on oil price volatility

International Nuclear Information System (INIS)

2010-01-01

This report proposes a detailed analysis of the past and possible evolution of oil markets in terms of price volatility, financial strategies and pricing. It discusses current reflections and actions aiming at improving oil market operation: the Joint Oil Data Initiative or JODI for oil data transparency, the works of the International Energy Forum (IEF), and the conceivable reforms of the oil financial markets. Then, it proposes and discusses four main strategic orientations for a better knowledge of oil markets by France and the improvement of their operation and transparency: to support IEF initiatives, to apply to oil financial markets the global orientations defined by the G20, to set additional specific rules, and to propose a true oil strategy for the European Union. These orientations are then broken up in 22 propositions

Recovery of oil from oil-in-water emulsion using biopolymers by adsorptive method.

Science.gov (United States)

Elanchezhiyan, S Sd; Sivasurian, N; Meenakshi, Sankaran

2014-09-01

In the present study, it is aimed to identify, a low cost sorbent for the recovery of oil from oil-in-water emulsion using biopolymers such as chitin and chitosan. Chitin has the greater adsorption capacity than chitosan due to its hydrophobic nature. The characterizations of chitin and chitosan were done using FTIR, SEM, EDAX, XRD, TGA and DSC techniques. Under batch equilibrium mode, a systematic study was performed to optimize the various equilibrium parameters viz., contact time, pH, dosage, initial concentration of oil, and temperature. The adsorption process reached equilibrium at 40 min of contact time and the percentage removal of oil was found to be higher (90%) in the acidic medium. The Freundlich and Langmuir models were applied to describe the equilibrium isotherms and the isotherm constants were calculated. Thermodynamic parameters such as ΔG°, ΔH° and ΔS° were calculated to find out the nature of the sorption mechanism. The kinetic studies were investigated with reaction-based and diffusion-based models. The suitable mechanism for the removal of oil has been established. Copyright © 2014 Elsevier B.V. All rights reserved.

An analysis of price and volatility transmission in butter, palm oil and crude oil markets

Directory of Open Access Journals (Sweden)

Dennis Bergmann

2016-11-01

Full Text Available Abstract Recent changes to the common agricultural policy (CAP saw a shift to greater market orientation for the EU dairy industry. Given this reorientation, the volatility of EU dairy commodity prices has sharply increased, creating the need to develop proper risk management tools to protect farmers’ income and to ensure stable prices for processors and consumers. In addition, there is a perceived threat that these commodities may be replaced by cheaper substitutes, such as palm oil, as dairy commodity prices become more volatile. Global production of palm oil almost doubled over the last decade while butter production remained relatively flat. Palm oil also serves as a feedstock for biodiesel production, thus establishing a new link between agricultural commodities and crude oil. Price and volatility transmission effects between EU and World butter prices, as well as between butter, palm oil and crude oil prices, before and after the Luxembourg agreement, are analysed. Vector autoregression (VAR models are applied to capture price transmission effects between these markets. These are combined with a multivariate GARCH model to account for potential volatility transmission. Results indicate strong price and volatility transmission effects between EU and World butter prices. EU butter shocks further spillover to palm oil volatility. In addition, there is evidence that oil prices spillover to World butter prices and World butter volatility.

CFD modeling of fouling in crude oil pre-heaters

International Nuclear Information System (INIS)

Bayat, Mahmoud; Aminian, Javad; Bazmi, Mansour; Shahhosseini, Shahrokh; Sharifi, Khashayar

2012-01-01

Highlights: ► A conceptual CFD-based model to predict fouling in industrial crude oil pre-heaters. ► Tracing fouling formation in the induction and developing continuation periods. ► Effect of chemical components, shell-side HTC and turbulent flow on the fouling rate. - Abstract: In this study, a conceptual procedure based on the computational fluid dynamic (CFD) technique has been developed to predict fouling rate in an industrial crude oil pre-heater. According to the developed CFD concept crude oil was assumed to be composed of three pseudo-components comprising of petroleum, asphaltene and salt. The binary diffusion coefficients were appropriately categorized into five different groups. The species transport model was applied to simulate the mixing and transport of chemical species. The possibility of adherence of reaction products to the wall was taken into account by applying a high viscosity for the products in competition with the shear stress on the wall. Results showed a reasonable agreement between the model predictions and the plant data. The CFD model could be applied to new operating conditions to investigate the details of the crude oil fouling in the industrial pre-heaters.

Bio-oils from biomass slow pyrolysis: a chemical and toxicological screening.

Science.gov (United States)

Cordella, Mauro; Torri, Cristian; Adamiano, Alessio; Fabbri, Daniele; Barontini, Federica; Cozzani, Valerio

2012-09-15

Bio-oils were produced from bench-scale slow-pyrolysis of three different biomass samples (corn stalks, poplar and switchgrass). Experimental protocols were developed and applied in order to screen their chemical composition. Several hazardous compounds were detected in the bio-oil samples analysed, including phenols, furans and polycyclic aromatic hydrocarbons. A procedure was outlined and applied to the assessment of toxicological and carcinogenic hazards of the bio-oils. The following hazardous properties were considered: acute toxicity; ecotoxicity; chronic toxicity; carcinogenicity. Parameters related to these properties were quantified for each component identified in the bio-oils and overall values were estimated for the bio-oils. The hazard screening carried out for the three bio-oils considered suggested that: (i) hazards to human health could be associated with chronic exposures to the bio-oils; (ii) acute toxic effects on humans and eco-toxic effects on aquatic ecosystems could also be possible in the case of loss of containment; and (iii) bio-oils may present a marginal potential carcinogenicity. The approach outlined allows the collection of screening information on the potential hazards posed by the bio-oils. This can be particularly useful when limited time and analytical resources reduce the possibility to obtain detailed specific experimental data. Copyright © 2012 Elsevier B.V. All rights reserved.

Oil spill dispersants. Risk assessment for Swedish waters

International Nuclear Information System (INIS)

Lindgren, C.; Lager, H.; Fejes, J.

2001-12-01

IVL has compiled a list of the international usage of oil spill dispersants and presents the technical limitations with the use of such agents as well as the biological effects of these chemical products. IVL, has also conducted an analysis of the pros and cons to using dispersants against oil spills in waters and has applied this with a risk assessment of chemical methods to combat oil spills in the Kattegat and Skagerrak and the Baltic Sea

Silicon homo-heterojunction solar cells: A promising candidate to realize high performance more stably

Directory of Open Access Journals (Sweden)

Miao Tan

2017-08-01

Full Text Available We have investigated the influences of diverse physical parameters on the performances of a silicon homo-heterojunction (H-H solar cell, which encompasses both homojunction and heterojunction, together with their underlying mechanisms by the aid of AFORS-HET simulation. It is found that the performances of H-H solar cell are less sensitive to (i the work function of the transparent conductive oxide layer, (ii the interfacial density of states at the front hydrogenated amorphous silicon/crystalline silicon (a-Si:H/c-Si interface, (iii the peak dangling bond defect densities within the p-type a-Si:H (p-a-Si:H layer, and (iv the doping concentration of the p-a-Si:H layer, when compared to that of the conventional heterojunction with intrinsic thin layer (HIT counterparts. These advantages are due to the fact that the interfacial recombination and the recombination within the a-Si:H region are less affected by all the above parameters, which fundamentally benefit from the field-effect passivation of the homojunction. Therefore, the design of H-H structure can provide an opportunity to produce high-efficiency solar cells more stably.

Silicon homo-heterojunction solar cells: A promising candidate to realize high performance more stably

Science.gov (United States)

Tan, Miao; Zhong, Sihua; Wang, Wenjie; Shen, Wenzhong

2017-08-01

We have investigated the influences of diverse physical parameters on the performances of a silicon homo-heterojunction (H-H) solar cell, which encompasses both homojunction and heterojunction, together with their underlying mechanisms by the aid of AFORS-HET simulation. It is found that the performances of H-H solar cell are less sensitive to (i) the work function of the transparent conductive oxide layer, (ii) the interfacial density of states at the front hydrogenated amorphous silicon/crystalline silicon (a-Si:H/c-Si) interface, (iii) the peak dangling bond defect densities within the p-type a-Si:H (p-a-Si:H) layer, and (iv) the doping concentration of the p-a-Si:H layer, when compared to that of the conventional heterojunction with intrinsic thin layer (HIT) counterparts. These advantages are due to the fact that the interfacial recombination and the recombination within the a-Si:H region are less affected by all the above parameters, which fundamentally benefit from the field-effect passivation of the homojunction. Therefore, the design of H-H structure can provide an opportunity to produce high-efficiency solar cells more stably.

Transgenic oil palm: production and projection.

Science.gov (United States)

Parveez, G K; Masri, M M; Zainal, A; Majid, N A; Yunus, A M; Fadilah, H H; Rasid, O; Cheah, S C

2000-12-01

Oil palm is an important economic crop for Malaysia. Genetic engineering could be applied to produce transgenic oil palms with high value-added fatty acids and novel products to ensure the sustainability of the palm oil industry. Establishment of a reliable transformation and regeneration system is essential for genetic engineering. Biolistic was initially chosen as the method for oil palm transformation as it has been the most successful method for monocotyledons to date. Optimization of physical and biological parameters, including testing of promoters and selective agents, was carried out as a prerequisite for stable transformation. This has resulted in the successful transfer of reporter genes into oil palm and the regeneration of transgenic oil palm, thus making it possible to improve the oil palm through genetic engineering. Besides application of the Biolistics method, studies on transformation mediated by Agrobacterium and utilization of the green fluorescent protein gene as a selectable marker gene have been initiated. Upon the development of a reliable transformation system, a number of useful targets are being projected for oil palm improvement. Among these targets are high-oleate and high-stearate oils, and the production of industrial feedstock such as biodegradable plastics. The efforts in oil palm genetic engineering are thus not targeted as commodity palm oil. Due to the long life cycle of the palm and the time taken to regenerate plants in tissue culture, it is envisaged that commercial planting of transgenic palms will not occur any earlier than the year 2020.

75 FR 76742 - Detecting Oil Leaks From Vessels Into the Water

Science.gov (United States)

2010-12-09

... to detect leaks from oil tanks into the water? (E) What is the threshold for detection, accuracy... than leak detection from oil cargo tanks into the water? (H) Are methods or equipment being applied for... DEPARTMENT OF HOMELAND SECURITY Coast Guard [Docket No. USCG-2010-1085] Detecting Oil Leaks From...

A method of applying two-pump system in automatic transmissions for energy conservation

Directory of Open Access Journals (Sweden)

Peng Dong

2015-06-01

Full Text Available In order to improve the hydraulic efficiency, modern automatic transmissions tend to apply electric oil pump in their hydraulic system. The electric oil pump can support the mechanical oil pump for cooling, lubrication, and maintaining the line pressure at low engine speeds. In addition, the start–stop function can be realized by means of the electric oil pump; thus, the fuel consumption can be further reduced. This article proposes a method of applying two-pump system (one electric oil pump and one mechanical oil pump in automatic transmissions based on the forward driving simulation. A mathematical model for calculating the transmission power loss is developed. The power loss transfers to heat which requires oil flow for cooling and lubrication. A leakage model is developed to calculate the leakage of the hydraulic system. In order to satisfy the flow requirement, a flow-based control strategy for the electric oil pump is developed. Simulation results of different driving cycles show that there is a best combination of the size of electric oil pump and the size of mechanical oil pump with respect to the optimal energy conservation. Besides, the two-pump system can also satisfy the requirement of the start–stop function. This research is extremely valuable for the forward design of a two-pump system in automatic transmissions with respect to energy conservation and start–stop function.

Oil defect detection of electrowetting display

Science.gov (United States)

Chiang, Hou-Chi; Tsai, Yu-Hsiang; Yan, Yung-Jhe; Huang, Ting-Wei; Mang, Ou-Yang

2015-08-01

In recent years, transparent display is an emerging topic in display technologies. Apply in many fields just like mobile device, shopping or advertising window, and etc. Electrowetting Display (EWD) is one kind of potential transparent display technology advantages of high transmittance, fast response time, high contrast and rich color with pigment based oil system. In mass production process of Electrowetting Display, oil defects should be found by Automated Optical Inspection (AOI) detection system. It is useful in determination of panel defects for quality control. According to the research of our group, we proposed a mechanism of AOI detection system detecting the different kinds of oil defects. This mechanism can detect different kinds of oil defect caused by oil overflow or material deteriorated after oil coating or driving. We had experiment our mechanism with a 6-inch Electrowetting Display panel from ITRI, using an Epson V750 scanner with 1200 dpi resolution. Two AOI algorithms were developed, which were high speed method and high precision method. In high precision method, oil jumping or non-recovered can be detected successfully. This mechanism of AOI detection system can be used to evaluate the oil uniformity in EWD panel process. In the future, our AOI detection system can be used in quality control of panel manufacturing for mass production.

Evaluation of Reservoir Wettability and its Effect on Oil Recovery

Energy Technology Data Exchange (ETDEWEB)

Buckley, Jill S.

2002-01-29

The objectives of this five-year project were: (1) to achieve improved understanding of the surface and interfacial properties of crude oils and their interactions with mineral surfaces, (2) to apply the results of surface studies to improve predictions of oil production from laboratory measurements, and (3) to use the results of this research to recommend ways to improve oil recovery by waterflooding.

Preventive conservation applied to "Casa dos Patudos" oil painting collection

Directory of Open Access Journals (Sweden)

Mafalda Fernandes

2016-01-01

Full Text Available The main objective of this work was the identification of specific risks affecting the collection of oil paintings in the historic house "Casa dos Patudos" (Alpiarça, Portugal and the development of mitigation strategies for the risks encountered. The methodology used was proposed by the Canadian Conservation Institute. The results showed that the main risks affecting this collection result from incorrect handling, increase in paint detachment due to the maintenance of paintings with paint lifting on display, occurrence of insect pests, high fluctuations in relative humidity and, excessive exposure to ultraviolet radiation. Several preventive conservation strategies to mitigate these risks are proposed.

Price implications for Russia's oil refining

International Nuclear Information System (INIS)

Khartukov, Eugene M.

1998-01-01

Over the past several years, Russia's oil industry has undergone its radical transformation from a wholly state-run and generously subsidized oil distribution system toward a substantially privatized, cash-strapped, and quasi-market ''petropreneurship''. This fully applies to the industry's downstream sector. Still unlike more dynamic E and C operations, the country's refining has turned out better fenced off competitive market forces and is less capable to respond to market imperatives. Consequently, jammed between depressed product prices and persistent feedstock costs, Russian refiners were badly hit by the world oil glut - which has made a radical modernization of the obsolete refining sector clearly a must. (author)

40 CFR 63.686 - Standards: Oil-water and organic-water separators.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 10 2010-07-01 2010-07-01 false Standards: Oil-water and organic-water... Operations § 63.686 Standards: Oil-water and organic-water separators. (a) The provisions of this section apply to the control of air emissions from oil-water separators and organic-water separators for which...

Controlling Air Pollution from the Oil and Natural Gas Industry

Science.gov (United States)

EPA regulations for the oil and natural gas industry help combat climate change and reduce air pollution that harms public health. EPA’s regulations apply to oil production, and the production, process, transmission and storage of natural gas.

Louisiana's oil spill program : new developments

International Nuclear Information System (INIS)

Debusschere, K.; Tedford, R.; Brolin, J.; Lorentz, W.

2000-01-01

The Louisiana Oil Spill Coordinator's Office (LOSCO) was established to improve oil spill response, spill prevention and coordination. Louisiana is challenged with having the highest exposure of oil spills because a large portion of its economy is based on oil and gas exploration and production. LOSCO will find ways to minimize the risk of unauthorized oil spills and will address damage assessment and restoration efforts. The aging oil and gas infrastructure in Louisiana has also been recognized as a potential major source for oil spills. LOSCO locates potential spill locations and assesses the risks associated with the sites, some of which are 100 years old. LOSCO also initiated the following two programs: (1) the Abandoned Barge Program initiated in 1993 to remove abandoned barges that pose a high risk for oil discharge, and (2) the Abandoned Non-Hazardous Oil Waste (NOW) Pit and Facility Program initiated in 1992 to locate and remove structures, pits and wells that pose a risk for oil spills. About 25,000 facilities, pits, sumps and reservoirs have been inventoried and evaluated to determine if they pose a risk to human health or the environment. The Louisiana Oil Spill Prevention and Response Act (OSPRA) of 1991 allocates up to $2 million per year for the abatement of oil spills from abandoned facilities in Louisiana. The state legislature has also created the Applied and Educational Oil Spill Research and Development Program (OSRADP) to fund oil spill research. Since 1993, OSRADP has granted 68 awards in support of 42 projects, many of which focused on recovery and cleanup methods including in-situ burning, fate and effect of oil in Louisiana environments, bioremediation, phytoremediation, composting, chemical cleaners, dispersants, sorbents, and solidifiers. 3 refs., 1 tab

Financial market pressure, tacit collusion and oil price formation

International Nuclear Information System (INIS)

Aune, Finn Roar; Rosendahl, Knut Einar; Mohn, Klaus; Osmundsen, Petter

2010-01-01

We explore a hypothesis that a change in investment behaviour among international oil companies (IOC) towards the end of the 1990s had long-lived effects on OPEC strategies, and on oil price formation. Coordinated investment constraints were imposed on the IOCs through financial market pressures for improved short-term profitability in the wake of the Asian economic crisis. A partial equilibrium model for the global oil market is applied to compare the effects of these tacitly collusive capital constraints on oil supply with an alternative characterised by industrial stability. Our results suggest that even temporary economic and financial shocks may have a long-term impact on oil price formation. (author)

Enhanced Oil Recovery (EOR by Miscible CO2 and Water Flooding of Asphaltenic and Non-Asphaltenic Oils

Directory of Open Access Journals (Sweden)

Edwin A. Chukwudeme

2009-09-01

Full Text Available An EOR study has been performed applying miscible CO2 flooding and compared with that for water flooding. Three different oils are used, reference oil (n-decane, model oil (n-C10, SA, toluene and 0.35 wt % asphaltene and crude oil (10 wt % asphaltene obtained from the Middle East. Stearic acid (SA is added representing a natural surfactant in oil. For the non-asphaltenic oil, miscible CO2 flooding is shown to be more favourable than that by water. However, it is interesting to see that for first years after the start of the injection (< 3 years it is shown that there is almost no difference between the recovered oils by water and CO2, after which (> 3 years oil recovery by gas injection showed a significant increase. This may be due to the enhanced performance at the increased reservoir pressure during the first period. Maximum oil recovery is shown by miscible CO2 flooding of asphaltenic oil at combined temperatures and pressures of 50 °C/90 bar and 70 °C/120 bar (no significant difference between the two cases, about 1% compared to 80 °C/140 bar. This may support the positive influence of the high combined temperatures and pressures for the miscible CO2 flooding; however beyond a certain limit the oil recovery declined due to increased asphaltene deposition. Another interesting finding in this work is that for single phase oil, an almost linear relationship is observed between the pressure drop and the asphaltene deposition regardless of the flowing fluid pressure.

Phenomenology of two-dimensional stably stratified turbulence under large-scale forcing

KAUST Repository

Kumar, Abhishek; Verma, Mahendra K.; Sukhatme, Jai

2017-01-01

In this paper, we characterise the scaling of energy spectra, and the interscale transfer of energy and enstrophy, for strongly, moderately and weakly stably stratified two-dimensional (2D) turbulence, restricted in a vertical plane, under large-scale random forcing. In the strongly stratified case, a large-scale vertically sheared horizontal flow (VSHF) coexists with small scale turbulence. The VSHF consists of internal gravity waves and the turbulent flow has a kinetic energy (KE) spectrum that follows an approximate k−3 scaling with zero KE flux and a robust positive enstrophy flux. The spectrum of the turbulent potential energy (PE) also approximately follows a k−3 power-law and its flux is directed to small scales. For moderate stratification, there is no VSHF and the KE of the turbulent flow exhibits Bolgiano–Obukhov scaling that transitions from a shallow k−11/5 form at large scales, to a steeper approximate k−3 scaling at small scales. The entire range of scales shows a strong forward enstrophy flux, and interestingly, large (small) scales show an inverse (forward) KE flux. The PE flux in this regime is directed to small scales, and the PE spectrum is characterised by an approximate k−1.64 scaling. Finally, for weak stratification, KE is transferred upscale and its spectrum closely follows a k−2.5 scaling, while PE exhibits a forward transfer and its spectrum shows an approximate k−1.6 power-law. For all stratification strengths, the total energy always flows from large to small scales and almost all the spectral indicies are well explained by accounting for the scale-dependent nature of the corresponding flux.

Phenomenology of two-dimensional stably stratified turbulence under large-scale forcing

KAUST Repository

Kumar, Abhishek

2017-01-11

In this paper, we characterise the scaling of energy spectra, and the interscale transfer of energy and enstrophy, for strongly, moderately and weakly stably stratified two-dimensional (2D) turbulence, restricted in a vertical plane, under large-scale random forcing. In the strongly stratified case, a large-scale vertically sheared horizontal flow (VSHF) coexists with small scale turbulence. The VSHF consists of internal gravity waves and the turbulent flow has a kinetic energy (KE) spectrum that follows an approximate k−3 scaling with zero KE flux and a robust positive enstrophy flux. The spectrum of the turbulent potential energy (PE) also approximately follows a k−3 power-law and its flux is directed to small scales. For moderate stratification, there is no VSHF and the KE of the turbulent flow exhibits Bolgiano–Obukhov scaling that transitions from a shallow k−11/5 form at large scales, to a steeper approximate k−3 scaling at small scales. The entire range of scales shows a strong forward enstrophy flux, and interestingly, large (small) scales show an inverse (forward) KE flux. The PE flux in this regime is directed to small scales, and the PE spectrum is characterised by an approximate k−1.64 scaling. Finally, for weak stratification, KE is transferred upscale and its spectrum closely follows a k−2.5 scaling, while PE exhibits a forward transfer and its spectrum shows an approximate k−1.6 power-law. For all stratification strengths, the total energy always flows from large to small scales and almost all the spectral indicies are well explained by accounting for the scale-dependent nature of the corresponding flux.

From rocks to oil : researchers become the first in the world to determine the age of oil

Energy Technology Data Exchange (ETDEWEB)

Crawshaw, C

2005-06-10

This article discussed the discovery of a method to accurately determine the age of oil. The discovery was made by two geologists at the University of Alberta, and provides critical information about the formation of oil which will help to better understand oil deposits. The scientists have suggested that the giant oil sand deposits in Alberta were formed 112 million years ago and not 60 million years ago as was previously thought. They used isotopes of rhenium and osmium, elements found in trace amounts in oil, to pinpoint when oil formed in the Western Canada Sedimentary Basin (WCSB), which contains much of the world's oil sands. It was previously thought that the time at which oil was produced from a rock and migrated as fluid could be deduced from looking at geologic relationships. This is the first time that a direct determination using any isotopic method has be applied to determine age. The research findings are expected to change the way geologists understand the evolution of the basin. It was concluded that while the discovery answers some questions about hydrocarbons, many others remain. However, the presence of an absolute number will help geologists to re-evaluate other knowledge. 1 fig.

Alberta's oil sands fiscal system : historical context and system performance

International Nuclear Information System (INIS)

2007-01-01

This report described the fiscal system applied to Alberta's oil sands. It is the first technical report forming part of a series designed to provide information and to invite comment as part of the Government of Alberta's public review of the fiscal system applied to the province's oil and gas resources. Specifically, this report assessed the robustness of Alberta's oil sands fiscal system and assessed how the regime balanced the risks and rewards to both investors and Albertans across a range of expected and probable economic outcomes. The report provided an explanation of the history and context of Alberta's royalty regime and included a case-by-case approach. It also provided a discussion of the oil sands fiscal system description. Next, it described the methodology employed for the analysis of the oil sands fiscal system. It also provided the assumptions for 5 scenario cases and presented the fiscal map approach for assessing project economics and fiscal system performance. Last, summary observations were presented. It was found that the oil sands fiscal system is very flexible for adverse economic conditions and much less so for highly profitable conditions. tabs., figs

Large Oil Spill Classification Using SAR Images Based on Spatial Histogram

Science.gov (United States)

Schvartzman, I.; Havivi, S.; Maman, S.; Rotman, S. R.; Blumberg, D. G.

2016-06-01

Among the different types of marine pollution, oil spill is a major threat to the sea ecosystems. Remote sensing is used in oil spill response. Synthetic Aperture Radar (SAR) is an active microwave sensor that operates under all weather conditions and provides information about the surface roughness and covers large areas at a high spatial resolution. SAR is widely used to identify and track pollutants in the sea, which may be due to a secondary effect of a large natural disaster or by a man-made one . The detection of oil spill in SAR imagery relies on the decrease of the backscattering from the sea surface, due to the increased viscosity, resulting in a dark formation that contrasts with the brightness of the surrounding area. Most of the use of SAR images for oil spill detection is done by visual interpretation. Trained interpreters scan the image, and mark areas of low backscatter and where shape is a-symmetrical. It is very difficult to apply this method for a wide area. In contrast to visual interpretation, automatic detection algorithms were suggested and are mainly based on scanning dark formations, extracting features, and applying big data analysis. We propose a new algorithm that applies a nonlinear spatial filter that detects dark formations and is not susceptible to noises, such as internal or speckle. The advantages of this algorithm are both in run time and the results retrieved. The algorithm was tested in genesimulations as well as on COSMO-SkyMed images, detecting the Deep Horizon oil spill in the Gulf of Mexico (occurred on 20/4/2010). The simulation results show that even in a noisy environment, oil spill is detected. Applying the algorithm to the Deep Horizon oil spill, the algorithm classified the oil spill better than focusing on dark formation algorithm. Furthermore, the results were validated by the National Oceanic and Atmospheric Administration (NOAA) data.

LARGE OIL SPILL CLASSIFICATION USING SAR IMAGES BASED ON SPATIAL HISTOGRAM

Directory of Open Access Journals (Sweden)

I. Schvartzman

2016-06-01

Full Text Available Among the different types of marine pollution, oil spill is a major threat to the sea ecosystems. Remote sensing is used in oil spill response. Synthetic Aperture Radar (SAR is an active microwave sensor that operates under all weather conditions and provides information about the surface roughness and covers large areas at a high spatial resolution. SAR is widely used to identify and track pollutants in the sea, which may be due to a secondary effect of a large natural disaster or by a man-made one . The detection of oil spill in SAR imagery relies on the decrease of the backscattering from the sea surface, due to the increased viscosity, resulting in a dark formation that contrasts with the brightness of the surrounding area. Most of the use of SAR images for oil spill detection is done by visual interpretation. Trained interpreters scan the image, and mark areas of low backscatter and where shape is a-symmetrical. It is very difficult to apply this method for a wide area. In contrast to visual interpretation, automatic detection algorithms were suggested and are mainly based on scanning dark formations, extracting features, and applying big data analysis. We propose a new algorithm that applies a nonlinear spatial filter that detects dark formations and is not susceptible to noises, such as internal or speckle. The advantages of this algorithm are both in run time and the results retrieved. The algorithm was tested in genesimulations as well as on COSMO-SkyMed images, detecting the Deep Horizon oil spill in the Gulf of Mexico (occurred on 20/4/2010. The simulation results show that even in a noisy environment, oil spill is detected. Applying the algorithm to the Deep Horizon oil spill, the algorithm classified the oil spill better than focusing on dark formation algorithm. Furthermore, the results were validated by the National Oceanic and Atmospheric Administration (NOAA data.

Oil analysis in machine diagnostics

Energy Technology Data Exchange (ETDEWEB)

Vaehaeoja, P.

2006-07-01

This study concentrates on developing and tuning various oil analysis methods to meet the requirements of modern industry and environmental analytics. Oil analysis methods form a vital part of techniques used to monitor the condition of machines and may help to improve the overall equipment effectiveness value of a factory in a significant manner. Worm gears are used in various production machines, and their breakdowns may cause significant production losses. Wearing of these gears is relatively difficult to monitor with vibration analysis. Analysis of two indicator metals, copper and iron, may reveal wearing phenomena of worm gears effectively, and savings can be significant. Effective wear metal analysis requires good tools. ICP-OES with kerosene dilution is widely used in wear metal analysis, but purchasing and using of ICP-OES is expensive. A cheaper FAAS technique with similar pre-treatment of oil samples was tested and it proved to be useful especially in analyzing small amounts of samples. The accuracy of FAAS was sufficient for quantitative work in machine diagnostics and waste oil characterization. Solid debris analyses are useful in oil contamination control as well as in detection of wearing mechanisms. Membrane filtration, optical microscopy, SEM and automatic particle counting were applied in analysis of rolling and gear oils. Particle counting is an effective way to detect oil contamination, but in the studied cases even larger particles than those detected in normal ISO classes would be informative. However, membrane filtration and optical microscopy may reveal the wearing machine element exactly. Additives provide oils with desired properties thus they should be monitored intensively. A FTIR method for quantitative analysis of fatty alcohols and fatty acid esters in machinery oils was developed during this work. It has already been used successfully in quantitative and qualitative analysis of machinery oil samples. Various kinds of oils may be

An oil spill-food chain interaction model for coastal waters

International Nuclear Information System (INIS)

Yew Hoong Gin, K.; Huda, Md. K.; Tkalich, P.

2001-01-01

An oil spill-food chain interaction model, composed of a multiphase oil spill model (MOSM) and a food chain model, has been developed to assess the probable impacts of oil spills on several key marine organisms (phytoplankton, zooplankton, small fish, large fish and benthic invertebrates). The MOSM predicts oil slick thickness on the water surface; dissolved, emulsified and particulate oil concentrations in the water column; and dissolved and particulate oil concentrations in bed sediments. This model is used to predict the fate of oil spills and transport with respect to specific organic compounds, while the food chain model addresses the uptake of toxicant by marine organisms. The oil spill-food chain interaction model can be used to assess the environmental impacts of oil spills in marine ecosystems. The model is applied to the recent Evoikos-Orapin Global oil spill that occurred in the Singapore Strait. (author)

Microbial population changes during bioremediation of an experimental oil spill

International Nuclear Information System (INIS)

MacNaughton, S.J.; Stephen, J.R.; Chang, Y.J.; Davis, G.A.; White, D.C.; Oak Ridge National Lab., TN

1999-01-01

Three crude oil bioremediation techniques were applied in a randomized block field experiment simulating a coastal oil spill. Four treatments (no oil control, oil alone, oil plus nutrients, and oil plus nutrients plus an indigenous inoculum) were applied. In situ microbial community structures were monitored by phospholipid fatty acid (PLFA) analysis and 16S rDNA PCR-denaturing gradient gel electrophoresis (DGGE) to (i) identify the bacterial community members responsible for the decontamination of the site and (ii) define an end point for the removal of the hydrocarbon substrate. The results of PLFA analysis demonstrated a community shift in all plots from primarily eukaryotic biomass to gram-negative bacterial biomass with time. PLFA profiles from the oiled plots suggested increased gram-negative biomass and adaptation to metabolic stress compared to unoiled controls. DGGE analysis of untreated control plots revealed a simple, dynamic dominant population structure throughout the experiment. This banding pattern disappeared in all oiled plots, indicating that the structure and diversity of the dominant bacterial community changed substantially. No consistent differences were detected between nutrient-amended and indigenous inoculum-treated plots, but both differed from the oil-only plots. Prominent bands were excised for sequence analysis and indicated that oil treatment encouraged the growth of gram-negative microorganisms within the α-proteobacteria and Flexibacter-Cytophaga-Bacteroides phylum. α-Proteobacteria were never detected in unoiled controls. PLFA analysis indicated that by week 14 the microbial community structures of the oiled plots were becoming similar to those of the unoiled controls from the same time point, but DGGE analysis suggested that major differences in the bacterial communities remained

Antioxidant properties of volatile oils obtained from Artemisia taurica ...

African Journals Online (AJOL)

In this study, the antioxidant properties of volatile oils obtained from the earth parts of the Artemisia taurica Willd. and Salvia kronenburgii Rech. Fil. plants and their effects on xanthine oxidase enzyme were studied. The chemical contents of each volatile oil were determined by applying gas chromatograpghy-mass ...

[Establishment and application of a Vero cell line stably expressing raccoon dog SLAM, the cellular receptor of canine distemper virus].

Science.gov (United States)

Zhao, Jianjun; Yan, Ruxun; Zhang, Hailing; Zhang, Lei; Hu, Bo; Bai, Xue; Shao, Xiqun; Chai, Xiuli; Yan, Xijun; Wu, Wei

2012-12-04

The signaling lymphocyte activation molecule (SLAM, also known as CD150), is used as a cellular receptor by canine distemper virus (CDV). Wild-type strains of CDVs can be isolated and propagated efficiently in non-lymphoid cells expressing this protein. Our aim is to establish a Vero cells expressing raccoon dog SLAM (rSLAM) to efficiently isolate CDV from pathological samples. A eukaryotic expression plasmid, pIRES2-EGFP-rSLAMhis, containing rSLAM gene fused with six histidine-coding sequence, EGFP gene, and neomycin resistance gene was constructed. After transfection with the plasmid, a stable cell line, Vero-rSLAM, was screened from Vero cells with the identification of EGFP reporter and G418 resistance. Three CD positive specimens from infected foxes and raccoon dogs were inoculated to Vero-rSLAM cells for CDV isolation. Foxes and raccoon dogs were inoculated subcutaneously LN (10)fl strain with 4 x 10(2.39)TCID50 dose to evaluate pathogenicity of CDV isolations. The rSLAMh fused gene was shown to transcript and express stably in Vero-rSLAM cells by RT-PCR and Immunohistochemistry assay. Three CDV strains were isolated successfully in Vero-rSLAM cells 36 -48 hours after inoculation with spleen or lung specimens from foxes and raccoon dogs with distemper. By contrast, no CDV was recovered from those CD positive specimens when Vero cells were used for virus isolation. Infected foxes and raccoon dogs with LN(10)f1 strain all showed typical CD symptoms and high mortality (2/3 for foxes and 3/3 for raccoon dogs) in 22 days post challenge. Our results indicate that Vero-rSLAM cells stably expressing raccoon dog SLAM are highly sensitive to CDV in clinical specimens and the CDV isolation can maintain high virulence to its host animals.

Effect of Thymus vulgaris L. Essential Oil on Oxidative Stability of Virgin Olive Oil and Its Synergy with Citric Acid

Directory of Open Access Journals (Sweden)

Malihe Keramat

2017-09-01

Full Text Available Background: Since usage of synthetic antioxidants has been under question due to their toxicity and possible carcinogenicity, there is still interest in developing plant-derived natural antioxidants, especially from edible plants. This study investigated the effect of Thymus vulgaris L. essential oil on virgin olive oil oxidation in comparison with tocopheryl acetate and butylated hydroxytoluene (BHT. Furthermore, the synergistic activities of citric acid with natural and synthetic antioxidants were determined. Methods: T. vulgaris essential oil was added to the virgin olive oil at a concentration of 1000 ppm. The BHT and tocopheryl acetate were added to the virgin olive oil at 100 ppm concentration. Virgin olive oil samples were stored at 60°C for 16 days. The peroxide value, p-anisidine value, K232, and K268 values were measured every 4 days. Changes in chlorophyll and carotenoid contents of virgin olive oil samples were determined at the beginning and end of storage period. Results: T. vulgaris essential oil significantly reduced the peroxide value, p-anisidine value, K232, and K268 values of virgin olive oil. The effect of T.vulgaris essential oil on retarding virgin olive oil oxidation was similar to the effect of BHT. By comparison, tocopheryl acetate was less effective in reducing the oxidation of virgin olive oil. Furthermore, T. vulgaris essential oil could preserve chlorophyll and carotenoid of virgin olive oil during storage period. Conclusion: T. vulgaris essential oil can be applied to increase the oxidative stability of virgin olive oil, and can protect the chlorophyll and carotenoid of virgin olive oil.

TESTING THE GENERALIZATION EFFICIENCY OF OIL SLICK CLASSIFICATION ALGORITHM USING MULTIPLE SAR DATA FOR DEEPWATER HORIZON OIL SPILL

Directory of Open Access Journals (Sweden)

C. Ozkan

2012-07-01

Full Text Available Marine oil spills due to releases of crude oil from tankers, offshore platforms, drilling rigs and wells, etc. are seriously affecting the fragile marine and coastal ecosystem and cause political and environmental concern. A catastrophic explosion and subsequent fire in the Deepwater Horizon oil platform caused the platform to burn and sink, and oil leaked continuously between April 20th and July 15th of 2010, releasing about 780,000 m3 of crude oil into the Gulf of Mexico. Today, space-borne SAR sensors are extensively used for the detection of oil spills in the marine environment, as they are independent from sun light, not affected by cloudiness, and more cost-effective than air patrolling due to covering large areas. In this study, generalization extent of an object based classification algorithm was tested for oil spill detection using multiple SAR imagery data. Among many geometrical, physical and textural features, some more distinctive ones were selected to distinguish oil and look alike objects from each others. The tested classifier was constructed from a Multilayer Perception Artificial Neural Network trained by ABC, LM and BP optimization algorithms. The training data to train the classifier were constituted from SAR data consisting of oil spill originated from Lebanon in 2007. The classifier was then applied to the Deepwater Horizon oil spill data in the Gulf of Mexico on RADARSAT-2 and ALOS PALSAR images to demonstrate the generalization efficiency of oil slick classification algorithm.

Oil spill remote sensing sensors and aircraft

International Nuclear Information System (INIS)

Fingas, M.; Fruhwirth, M.; Gamble, L.

1992-01-01

The most common form of remote sensing as applied to oil spills is aerial remote sensing. The technology of aerial remote sensing, mainly from aircraft, is reviewed along with aircraft-mounted remote sensors and aircraft modifications. The characteristics, advantages, and limitations of optical techniques, infrared and ultraviolet sensors, fluorosensors, microwave and radar sensors, and slick thickness sensors are discussed. Special attention is paid to remote sensing of oil under difficult circumstances, such as oil in water or oil on ice. An infrared camera is the first sensor recommended for oil spill work, as it is the cheapest and most applicable device, and is the only type of equipment that can be bought off-the-shelf. The second sensor recommended is an ultraviolet and visible-spectrum device. The laser fluorosensor offers the only potential for discriminating between oiled and un-oiled weeds or shoreline, and for positively identifying oil pollution on ice and in a variety of other situations. However, such an instrument is large and expensive. Radar, although low in priority for purchase, offers the only potential for large-area searches and foul-weather remote sensing. Most other sensors are experimental or do not offer good potential for oil detection or mapping. 48 refs., 8 tabs

Microbial Succession in Co-Composting of Chipped-Ground Oil Palm Frond and Palm Oil Mill Effluent

International Nuclear Information System (INIS)

Mohd Najib Ahmad; Siti Ramlah Ahmad Ali; Mohd Ali Hassan

2016-01-01

Succession and phylogenetic profile of microbial communities during co-composting of chipped-ground oil palm frond (CG-OPF) and palm oil mill effluent (POME) were studied by apply-ing polymerase chain reaction-denaturant gel gradient electrophoresis (PCR-DGGE) analysis. The results indicated that the dominant microbial community detected was γ-Pro bacteria such as Pseudomonas sp. at almost throughout the composting process. Whilst Bacillales such as Bacillus psychrodurans were found toward the end of the composting process. Bacteroidetes such as Pedobacter solani were detected at the final stage of composting. This study contributed to a better understanding of microbial shifting and functioning throughout CG-OPF composting. Therefore, PCR-DGGE is recommended to be used as a tool to identify potential microbes that can contribute to a better performance of composting process. (author)

Computational model for the assessment of oil spill damages

Energy Technology Data Exchange (ETDEWEB)

Seip, K L; Heiberg, A B; Brekke, K A

1985-06-01

A description is given of the method and the required data of a model for calculating oil spill damages. Eleven damage attributes are defined: shorelength contaminated, shore restitution time, birds dead, restitution time for three groups of birds, open sea damages-two types, damages to recreation, economy and fisheries. The model has been applied in several cases of oil pollution assessments: in an examination of alternative models for the organization of oil spill combat in Norway, in the assessment of the damages coused by a blowout at Tromsoeflaket and in assessing a possible increase in oil spill preparedness for Svalbard. 56 references.

Belarus oil recovery. Final report

International Nuclear Information System (INIS)

1994-07-01

The Belarus Oil Recovery study was sponsored by the Danish Energy Agency and funded by the Danish State Oestlandepulje. The technical work was carried out by COWIconsult, the Danish Geological Survey, and Odin Energi in cooperation with the Belarus State Oil Company, Belorusneft. Belarus, a republic of the former USSR, is a landlocked country with limited and declining oil production. Oil production was initially established in Belarus in 1964, and 56 oil fields have been discovered to date. Production reached a peak of approximately 60,000 barrels per day in the mid 70's, but current production is only about 15,000 bpd, well below the required amount for self sufficiency. The intent of this feasibility study was to determine ways of improving the production potential of the oil fields of Belarus with western technology in order to make Belarus less dependent on other energy resources and on outside supplies of hydrocarbons. All the oil fields in Belarus are located in the Pripyat Basin. The structural complexity of the fields under study coupled with the rather poor reservoir quality have resulted in low oil recoveries, and the aim of the study is to recommend technology which might improve the performance of these reservoirs. Improved well stimulation and water injection using modern western technology is likely to improve recovery from these reservoirs. If this technology proves successful in these fields, then it could be applied to the other larger oil fields in Belarus. It is anticipated that the documented results would enable financing full scale implementation of the technology utilised which could contribute toward the solution of Belarus' energy requirements. (EG)

The freshwater biodegradation potential of nine Alaskan oils

International Nuclear Information System (INIS)

Blenkinsopp, S.; Segy, G.

1997-01-01

Nine Alaskan representative crude oils and oil products with freshwater spill potential were collected, aged, and incubated in the presence of the standard freshwater inoculum for 28 days at 10 degrees C. Detailed analytical chemistry was performed on all samples to quantify compositional changes. All of the samples tested exhibited measurable hydrocarbon loss as a result of incubation with the freshwater inoculum. Total saturate and total n-alkane biodegradation were greatly enhanced when nutrients were present. The oil products Jet B Fuel and Diesel No. 2 appear to be more biodegradable than the Alaska North Slope and Cook Inlet crude oils tested, while the Bunker C/Diesel mixture appears to be less biodegradable than these crude oils. These results suggest that the screening procedures described here can provide useful information when applying bioremediation technology to the cleanup of selected oiled freshwater environments. 10 refs., 5 tabs., 13 figs

Structural analysis of oil containment booms

International Nuclear Information System (INIS)

Badesha, S.S.; Hunt, J.; Wenck, E.

1993-01-01

In recent years, major oil spills, such as the Exxon Valdez incident, and many smaller spills have given rise to a worldwide marine environmental concern. One of the most successful devices for containing and facilitating the recovery of spilled oil, and one which does not endanger or alter the environment in any way, is the oil containment boom. Described in this paper is a finite element (FE)-based method for structural analysis of oil booms. In general, a number of FE models for a typical oil boom section are set up using the COSMOS FEA code. These models differ from one another in oil boom geometry, deployment configurations, and oil boom components. The FEA (fimite element analysis) models are made from the plate elements (skirt and tube), truss elements (tension members and ballast chain), and beam elements (end connector). Loads due to tow/current velocity, wind velocity, wave action, and ballasting, as determined from aero/hydrodynamics analysis, are applied as distributed pressures on the plate and beam elements. This method will predict boom tensile load strength, detailed stress distribution, and distortion characteristics for a particular boom with specific deployment configuration and environmental condition. The derived information can be used to highlight critical design features, thereby optimizing the oil boom design. Alternatively, this information can be used for the selection of an oil boom suited for a particular application and, more importantly, can provide the user with a control evaluation tool to determine whether a given oil boom design can withstand the stresses of its intended application

Delineation of the GPRC6A Receptor Signaling Pathways Using a Mammalian Cell Line Stably Expressing the Receptor

DEFF Research Database (Denmark)

Jacobsen, Stine Engesgaard; Nørskov-Lauritsen, Lenea; Thomsen, Alex Rojas Bie

2013-01-01

receptor has been suggested to couple to multiple G protein classes albeit via indirect methods. Thus, the exact ligand preferences and signaling pathways are yet to be elucidated. In the present study, we generated a Chinese hamster ovary (CHO) cell line that stably expresses mouse GPRC6A. In an effort...... and divalent cations, and for the first time, we conclusively show that these responses are mediated through the Gq pathway. We were not able to confirm previously published data demonstrating Gi- and Gs-mediated signaling; neither could we detect agonistic activity of testosterone and osteocalcin. Generation...... of the stable CHO cell line with robust receptor responsiveness and optimization of the highly sensitive homogeneous time resolved fluorescence technology allow fast assessment of Gq activation without previous manipulations like cotransfection of mutated G proteins. This cell-based assay system for GPRC6A...

Impact of Crude Oil Quality on the Refining Conditions and Composition of Nutraceuticals in Refined Palm Oil.

Science.gov (United States)

Sampaio, Klicia A; Ayala, Jose Vila; Van Hoed, Vera; Monteiro, Simone; Ceriani, Roberta; Verhé, Roland; Meirelles, Antonio J A

2017-08-01

Palm oil is the major vegetable oil used worldwide due to its unique properties. The effect of crude palm oil acidity on the final free fatty acids (FFA) content, neutral oil loss (NOL), and nutraceutical compounds, such as carotenes, total tocols (tocopherols and tocotrienols), squalene, and phytosterols was investigated. A central composite design was employed to study the influence of the refining conditions: temperature (200 to 260 °C), steam percentage (0.5% to 3.5%), and initial FFA content (2.2% to 6.0%) on the quality of the refined product. The results revealed that initial palm oil acidity is a statistically important parameter to obtain commercially acceptable values for final FFA content. The increase of temperature presented the most important effect on the reduction of all nutraceutical compounds. The highest tocopherols (88%), phytosterols (98%), and squalene retention (84%) was obtained when applying the mildest temperature (200 °C). From the experimental results, 3 equations were generated enabling the prediction of the free fatty acids content, the tocols content, and the losses of neutral oil. Therefore, this work contributes to the understanding and optimization of the process for the production of palm oil with high nutraceutical quality and low free fatty acid contents. © 2017 Institute of Food Technologists®.

Contact Hwersensitaity to Mustard Khal and Mustard Oil

Directory of Open Access Journals (Sweden)

J S Pasricha

1985-01-01

Full Text Available This report describes 2 females patients having contact dermatitis due to mustard khal the residue of,mustard seeds after the oil hasbeen extracted out. The dermatitis was caused by mbdng mustard khal with the cattle feed and was occurring on the hands and forearms, though the face, ear lobules and neck were also mvolved because of the practice of applying mustard oil on the hair. Patch tests were positive with the mustard khal and its fractionation products in both the patients and with mustard oil in one patient.

Bioremediation potential of coal-tar-oil-contaminated soil

International Nuclear Information System (INIS)

Lajoie, C.A.

1991-01-01

The bioremediation of coal tar oil contaminated soil was investigated in 90 day laboratory simulation experiments. The effect of soil moisture, humic acid amendment, and coal tar oil concentration on the rate of disappearance of individual coal tar oil constituents (PAHs and related compounds) was determined by methylene chloride extraction and gas chromatography. Mass balance experiments determined the fate of both the individual 14 C-labeled PAHs phenanthrene, pyrene, and benzo(a)pyrene, and the total coal tar oil carbon. Mineralization, volatilization, incorporation into microbial biomass, disappearance of individual coal tar oil constitutents, and the distribution of residual 14 C-activity in different soil fractions were measured. The rate of disappearance of coal tar oil constituents increased with increasing soil moisture over the experimental range. Humic acid amendment initially enhanced the rate of disappearance, but decreased the extent of disappearance. The amount of contamination removed decreased at higher coal tar oil concentrations. The practical limit for biodegradation in the system tested appeared to be between 1.0 and 2.5% coal tar oil. Mineralization accounted for 40 to 50% of the applied coal tar oil. Volatilization was a minor pathway of disappearance

Growth regulating properties of isoprene and isoprenoid-based essential oils.

Science.gov (United States)

Jones, Andrew Maxwell P; Shukla, Mukund R; Sherif, Sherif M; Brown, Paula B; Saxena, Praveen K

2016-01-01

Essential oils have growth regulating properties comparable to the well-documented methyl jasmonate and may be involved in localized and/or airborne plant communication. Aromatic plants employ large amounts of resources to produce essential oils. Some essential oils are known to contain compounds with plant growth regulating activities. However, the potential capacity of essential oils as airborne molecules able to modulate plant growth/development has remained uninvestigated. Here, we demonstrate that essential oils from eight taxonomically diverse plants applied in their airborne state inhibited auxin-induced elongation of Pisum sativum hypocotyls and Avena sativa coleoptiles. This response was also observed using five monoterpenes commonly found in essential oils as well as isoprene, the basic building block of terpenes. Upon transfer to ambient conditions, A. sativa coleoptiles resumed elongation, demonstrating an antagonistic relationship rather than toxicity. Inclusion of essential oils, monoterpenes, or isoprene into the headspace of culture vessels induced abnormal cellular growth along hypocotyls of Arabidopsis thaliana. These responses were also elicited by methyl jasmonate (MeJA); however, where methyl jasmonate inhibited root growth essential oils did not. Gene expression studies in A. thaliana also demonstrated differences between the MeJA and isoprenoid responses. This series of experiments clearly demonstrate that essential oils and their isoprenoid components interact with endogenous plant growth regulators when applied directly or as volatile components in the headspace. The similarities between isoprenoid and MeJA responses suggest that they may act in plant defence signalling. While further studies are needed to determine the ecological and evolutionary significance, the results of this study and the specialized anatomy associated with aromatic plants suggest that essential oils may act as airborne signalling molecules.

Evaluation of Reservoir Wettability and its Effect on Oil Recovery; FINAL

International Nuclear Information System (INIS)

Buckley, Jill S.

2002-01-01

The objectives of this five-year project were: (1) to achieve improved understanding of the surface and interfacial properties of crude oils and their interactions with mineral surfaces, (2) to apply the results of surface studies to improve predictions of oil production from laboratory measurements, and (3) to use the results of this research to recommend ways to improve oil recovery by waterflooding

ESTERIFICATION OF FATTY ACID FROM PALM OIL WASTE (SLUDGE OIL BY USING ALUM CATALYST

Directory of Open Access Journals (Sweden)

Thamrin Usman

2010-06-01

Full Text Available Esterification of fatty acids from palm oil waste (sludge oil as biodiesel liquid base has been done by using alum [Al2(SO43.14H2O] catalyst. Some reaction variables like reaction time, catalyst quantity, and molar ratio of sample-reactant was applied for optimal reaction. Yield of 94.66% was obtained at reaction condition 65 °C, 5 h, sample-reactant ratio 1:20, and catalyst quantity 3% (w/w. GC-MS analysis request showed that composition of methyl esters biodiesel are methyl caproic (0.67%, methyl lauric (0.21%, methyl miristic (1.96%, methyl palmitic (49.52%, methyl oleic (41.51%, and methyl stearic (6.13%. Physical properties of synthesized product (viscosity, refraction index and density are similar with those of commercial product.   Keywords: alum, biodiesel, esterification, sludge oil

Suppression of neutrophil accumulation in mice by cutaneous application of geranium essential oil

Directory of Open Access Journals (Sweden)

Oshima Haruyuki

2005-02-01

Full Text Available Abstract Background Previous studies suggested that essential oils suppressed the adherence response of human neutrophils in vitro and that intraperitoneal application of geranium oil suppressed the neutrophil accumulation into peritoneal cavity in vivo. Usually, essential oils are applied through skin in aromatherapy in inflammatory symptoms. The purpose of this study is to assess the effects of cutaneous application of essential oils on the accumulation of neutrophils in inflammatory sites in skin of mice. Methods Inflammation with accumulation of inflammatory cells was induced by injection of curdlan, a (1→3-β-D-glucan in skin or peritoneal cavity of mice. Essential oils were applied cutaneously to the mice immediately and 3 hr after intradermal injection of curdlan. The skin with inflammatory lesion was cut off 6 hr after injection of curdlan, and the homogenates were used for myeloperoxidase (MPO: a marker enzyme of neutrophil granule assay. Results The MPO activity of the skin lesion induced by curdlan was suppressed dose-dependently by cutaneous application of geranium oil. Other oils such as lavender, eucalyptus and tea tree oils also suppressed the activity, but their activities seemed weaker than geranium. Juniper oil didn't suppress the activity Conclusion Cutaneous application of essential oils, especially geranium oil, can suppress the inflammatory symptoms with neutrophil accumulation and edema.

Experimental investigation on a diode-pumped cesium-vapor laser stably operated at continuous-wave and pulse regime.

Science.gov (United States)

Chen, Fei; Xu, Dongdong; Gao, Fei; Zheng, Changbin; Zhang, Kuo; He, Yang; Wang, Chunrui; Guo, Jin

2015-05-04

Employing a fiber-coupled diode-laser with a center wavelength of 852.25 nm and a line width of 0.17 nm, experimental investigation on diode-end-pumped cesium (Cs) vapor laser stably operated at continuous-wave (CW) and pulse regime is carried out. A 5 mm long cesium vapor cell filled with 60 kPa helium and 20 kPa ethane is used as laser medium. Using an output coupler with reflectivity of 48.79%, 1.26 W 894.57 nm CW laser is obtained at an incident pump power of 4.76 W, corresponding an optical-optical efficiency of 26.8% and a slope-efficiency of 28.8%, respectively. The threshold temperature is 67.5 °C. Stable pulsed cesium laser with a maximum average output power of 2.6 W is obtained at a repetition rate of 76 Hz, and the pulse repetition rate can be extend to 1 kHz with a pulse width of 18 μs.

An Improvement in Biodiesel Production from Waste Cooking Oil by Applying Thought Multi-Response Surface Methodology Using Desirability Functions

Directory of Open Access Journals (Sweden)

Marina Corral Bobadilla

2017-01-01

Full Text Available The exhaustion of natural resources has increased petroleum prices and the environmental impact of oil has stimulated the search for an alternative source of energy such as biodiesel. Waste cooking oil is a potential replacement for vegetable oils in the production of biodiesel. Biodiesel is synthesized by direct transesterification of vegetable oils, which is controlled by several inputs or process variables, including the dosage of catalyst, process temperature, mixing speed, mixing time, humidity and impurities of waste cooking oil that was studied in this case. Yield, turbidity, density, viscosity and higher heating value are considered as outputs. This paper used multi-response surface methodology (MRS with desirability functions to find the best combination of input variables used in the transesterification reactions to improve the production of biodiesel. In this case, several biodiesel optimization scenarios have been proposed. They are based on a desire to improve the biodiesel yield and the higher heating value, while decreasing the viscosity, density and turbidity. The results demonstrated that, although waste cooking oil was collected from various sources, the dosage of catalyst is one of the most important variables in the yield of biodiesel production, whereas the viscosity obtained was similar in all samples of the biodiesel that was studied.

EXTRACTION OF OIL SEED PIN (Citrullus vulgaris BY LEACHING

Directory of Open Access Journals (Sweden)

Peggy Londoño

2014-12-01

Full Text Available Extraction of seed oil initially consisted in physicochemical study of the seed, in order to meet their nutritional content by performing various analyzes as moisture, ash, fat, phosphorus, proteins and carbohydrates. Then we proceeded with oil extraction equipment using solid-liquid extraction, Soxhlet using hexane as a solvent using the factorial design of the type 23. After, the crude oil was characterized and refined by the methodology of COVENIN norms, where the oil presented potential properties to elaborate soap in the cosmetic industry. Finally, a lipid profile was obtained by a gas chromatographic, the results showed highly unsaturated fatty acid contents (linoleic and oleic that gives it the potential to be applied as a capable oil with excellent properties and quality to human consume.

Enhanced oil recovery (EOR) by miscible CO{sub 2} and water flooding of asphaltenic and non-asphaltenic oils

Energy Technology Data Exchange (ETDEWEB)

Chukwudeme, E. A.; Hamouda, A. A. [Department of Petroleum Engineering, University of Stavanger, 4036 Stavanger (Norway)

2009-07-01

An EOR study has been performed applying miscible CO{sub 2} flooding and compared with that for water flooding. Three different oils are used, reference oil (n-decane), model oil (n-C10, SA, toluene and 0.35 wt % asphaltene) and crude oil (10 wt % asphaltene) obtained from the Middle East. Stearic acid (SA) is added representing a natural surfactant in oil. For the non-asphaltenic oil, miscible CO{sub 2} flooding is shown to be more favourable than that by water. However, it is interesting to see that for first years after the start of the injection (< 3 years) it is shown that there is almost no difference between the recovered oils by water and CO{sub 2}, after which (> 3 years) oil recovery by gas injection showed a significant increase. This may be due to the enhanced performance at the increased reservoir pressure during the first period. Maximum oil recovery is shown by miscible CO{sub 2} flooding of asphaltenic oil at combined temperatures and pressures of 50 {sup o}C/90 bar and 70 {sup o}C/120 bar (no significant difference between the two cases, about 1%) compared to 80 {sup o}C/140 bar. This may support the positive influence of the high combined temperatures and pressures for the miscible CO{sub 2} flooding; however beyond a certain limit the oil recovery declined due to increased asphaltene deposition. Another interesting finding in this work is that for single phase oil, an almost linear relationship is observed between the pressure drop and the asphaltene deposition regardless of the flowing fluid pressure. (author)

Optimization of the production of ethyl esters by ultrasound assisted reaction of soybean oil and ethanol

Directory of Open Access Journals (Sweden)

S. Rodrigues

2009-06-01

Full Text Available Biodiesel is a renewable liquid fuel that can be produced by a transesterification reaction between a vegetable oil and an alcohol. This paper evaluates and optimizes the production of ethyl esters (biodiesel from soybean oil and ethanol. The reaction was carried out by applying ultrasound under atmospheric pressure and ambient temperature. Response surface methodology was used to evaluate the influence of alcohol to oil molar ratio and catalyst concentration on the yield of conversion of soybean oil into ethyl esters. The process resulted in a maximum yield of 91.8% after 30 minutes of reaction. The process variables alcohol to oil ratio and catalyst to oil ratio were statistically significant regarding the yield of ethyl esters. The optimal operating condition was obtained applying an alcohol to oil molar ratio of 10.2 and a catalyst to oil weight ratio of 0.0035.

The future of oil and bioethanol in Brazil

International Nuclear Information System (INIS)

Moreira, Jose R.; Pacca, Sergio A.; Parente, Virginia

2014-01-01

This work compares the return on investments (ROI) of oil versus biofuels in Brazil. Although several renewable energy sources might displace oil, the country's forte is sugarcane biofuels. In our analysis we carry out simplified benefit–cost analyses of producing oil fields, pre-salt oil fields (without and with enhanced oil recovery), a business as the usual ethanol scenario, and a high ethanol scenario. Excluding the ROI from existing oil fields, which is the highest, when the discount rate is 4% or more, the ROI of the high ethanol scenario is greater than that of the ROI of pre-salt oil. Considering a US$40/t CO 2 tax, the high ethanol scenario's ROI is greater than the pre-salt oil's ROI if a discount rate of 2% or more is adopted. Moreover, the high ethanol scenario throughput up to 2070 compares to 97% of the pre-salt oil reserve without EOR, and demands 78% of its investment. Pre-salt oil production declines beyond 2042 when the country might become a net oil importer. In contrast, ethanol production reaches 2.1 million boe per day, and another 0.9 million boe of fossil demand is displaced through bioelectricity, yielding a total of 3 million boe (62% of the country's oil demand). - Highlights: • Cost-benefit analyses of pre-salt and biofuels in Brazil. • Hubbert model applied to pre-salt oil reserves. • Sustainable energy scenarios. • Carbon mitigation accounting based on biofuel scenarios. • Enhanced oil recovery effect on pre-salt oil reserves

Management of Oil Revenues: Has That of Azerbaijan Been Prudent?

Directory of Open Access Journals (Sweden)

Sarvar Gurbanov

2017-06-01

Full Text Available To help explain the common failure of oil or other natural resource exporting countries to diversify into industry, it has been common to trace this failure to real exchange rate appreciation. This has also been done in Azerbaijan. However, because Azerbaijan has devoted so much of its oil revenues to government investment, Azerbaijan provides a suitable case for examining an alternative link through government investment. This study applies the ARDL cointegration method to quarterly time series data on oil prices, government capital formation, non-oil exports and non-oil GDP to estimate the long run relationships linking oil prices to government investment expenditures and further to generation of non-oil GDP. The results show that despite the massive government investment expenditures, extremely little non-oil production of the tradable type has been generated, calling attention to the need for policy reform.

A laboratory approach for determining the effect of oils and dispersants on mangroves

Energy Technology Data Exchange (ETDEWEB)

Baca, B.J.

1982-10-01

An experimental approach was developed and applied to testing the effects of oil and dispersant combinations on the growth of mangrove seedlings (trees of the intertidal tropics). A controlled growth chamber was employed to test the effects of different oils and dispersed oils in an array of dosages applied to different parts of the plants. Preliminary test results are reported for two species of mangroves collected from five localities, including both oiled and unoiled estuaries. Differences occurred between species, substances, dosages, the part of the plant dosed, and the presence of chronic oil pollution at localities from which the stocks were collected. Avicennia germinans (L.) L. (black mangrove) was more sensitive than Rhizophora mangle L. (red mangrove) when exposed to almost all substances tested. Light Arabian crude oil (LA) and light Arabian crude oil dispersed (LAD) were the most toxic substances tested. No. 2 fuel oil (N2) and No. 2 fuel oil dispersed (N2D) were as toxic as LA and LAD, except for an increase (an enhancement effect) in foliage and stem growth in Avicennia at lower dosages. Bunker C oil (BC) was the least toxic of the oils tested, resulting in the reduction of foliage and stem growth only at the highest dosage tested in Avicennia. Bunker C oil dispersed (BCD) failed to show effects in either species at any dosage tested. The leaves of Rhizophora were the most sensitive part of the plant tested.

Toxicity of crude oil products and detergent on serum alkaline ...

African Journals Online (AJOL)

The comparative effect of exposing Clarias gariepinus juveniles (100.20 + 0.8g) to diferent concentrations of crude oil products and detergent were studied. Bonny Light Crude oil (BLCO), Premium motor spirit (PMS), Dual purpose kerosene (DPK) and Ariel Enzymax Detergent (AED) were respectively applied at three ...

Application of Sodium Ligno Sulphonate as Surfactant in Enhanced Oil Recovery and Its Feasibility Test for TPN 008 Oil

Science.gov (United States)

Prakoso, N. I.; Rochmadi; Purwono, S.

2018-04-01

One of enhanced oil recovery (EOR) methods is using surfactants to reduce the interfacial tension between the injected fluid and the oil in old reservoir. The most important principle in enhanced oil recovery process is the dynamic interaction of surfactants with crude oil. Sodium ligno sulphonate (SLS) is a commercial surfactant and already synthesized from palm solid waste by another researcher. This work aimed to apply SLS as a surfactant for EOR especially in TPN 008 oil from Pertamina Indonesia. In its application as an EOR’s surfactant, SLS shall be passed feasibility test like IFT, thermal stability, compatibility, filtration, molecular weight, density, viscosity and pH tests. The feasibility test is very important for a preliminary test prior to another advanced test. The results demonstrated that 1% SLS solution in formation water (TPN 008) had 0.254 mN/M IFT value and was also great in thermal stability, compatibility, filtration, molecular weight, viscosity and pH test.

Classification of weathered crude oils

International Nuclear Information System (INIS)

Vogt, N.B.; Sjoegren, C.E.; Lichtenthaler, G.

1987-01-01

The NORDTEST procedure (1) for oil spill identification has been applied successfully at several occasions. The NORDTEST procedure includes analyses of sulfur (XRF), vanadium and nickel (ICP/AAS), GC, HPLC and UV-fluorescence. The NORDTEST procedure does not include GC-MS as an analytical method. As part of a joint Nordic to evaluate the NORDTEST procedure for oil identification, with participants from Denmark, Sweden, Finland and Norway, thirty artificially weathered crude oils from four geographical regions have been analyzed (2). The analytical methods evaluated include sulfur analysis, vanadium and nickel analysis, infrared analysis, UV-fluorescence, gas chromatography, high pressure liquid chromatography and high resolution GC-mass spectrometry. Figure 1 shows the distribution of variables analyzed in each analytical method. The 190 variables from GC-MS were split into 7 groups according to chemical considerations. These were steranes (25 var.), triterpanes (16 var.), di(+)aromatics (63 var.), sulf. aromatics (30 var.), monoaromatics (19 var.), cycloalkanes (15 var.) and n-alkanes (22) variables. The data from these chemical analyses have been evaluated for use in oil spill identification purposes

The nature of oil shocks and the global economy

International Nuclear Information System (INIS)

Archanskaïa, Elizaveta; Creel, Jérôme; Hubert, Paul

2012-01-01

This paper identifies the main driving force behind oil price shocks in 1970–2006 by applying a simple identification strategy of supply-driven and demand-driven price shocks. The identification hypothesis states that supply-driven oil price shocks have a negative impact on the macroeconomic activity of countries, which are net consumers of oil while demand-driven oil price shocks do not have negative effects. In order to identify global demand-driven shocks, a weighted aggregate GDP series of countries, which are net consumers of oil, is constructed over 1970–2006. The key result is that the main driving force behind oil price shocks has changed from supply-driven shocks in 1970–1992 to demand-driven shocks in 1992–2006. - Highlights: ► We characterize the oil–macroeconomy relationship at the global level. ► We identify oil supply and oil demand shocks drawing on a AS/AS model. ► We construct an indicator of global activity for countries net consumers of oil. ► We use Qu-Perron break tests, TVP, Cyclical correlations and VARs. ► We show that the main driving force behind oil price shocks has changed around 1992.

Natural oils affect the human skin integrity and the percutaneous penetration of benzoic acid dose-dependently

DEFF Research Database (Denmark)

Nielsen, Jesper Bo

2006-01-01

three natural oils (eucalyptus oil, tea tree oil, peppermint oil) would affect the skin integrity and the percutaneous penetration of benzoic acid when applied topically in relevant concentrations. An experimental in vitro model using static diffusion cells mounted with human breast or abdominal skin...

Study on the basic properties of Indonesian oil sands

Energy Technology Data Exchange (ETDEWEB)

Wang, Qing; Jiang, Qian-qian; Bai, Jing-ru; Sun, Jian; Liu, Hong-peng [Northeast Dianli Univ., Jilin (China). Inst. of Energy and Power Engineering

2013-07-01

The basic properties of three Indonesian oil sands have been investigated. The results show that since the high content of volatile, heating value and oil yield, Indonesian oil sands could be combusted for power generation and retorting for oil refining. Moreover, oil sand ash with the low content of fixed carbon and high content of CaO, could not only be used as solid heat carrier during retorting, but also comprehensively used as construction material. Based on the thermogravimeric analysis (TGA), pyrolysis and combustion behaviors have been identified. As for pyrolysis, 350-520 C could be regarded as the major oil-producing region, the apparent activation energy E is not a constant obtained by distributed activation energy model (DAEM). For combustion, 620-800 C is the high-temperature oxidation (HTO) stage. TG-DTG extrapolation method was applied to determine the combustion characteristics parameters such as ignition temperature, burn-out temperature, combustion stability and combustion reactivity, and finally gave a comparison with those of oil shale and coal.

Large-scale bioenergy and oil forestry programs in rural China : an institutional analysis

NARCIS (Netherlands)

Li, Jia

2013-01-01

Liquid biofuel from oil crops are broadly promoted globally, among which biofuel from perennial wood species, as well as from bushes and small trees such as jatropha. In China, oil-bearing small trees, which mainly grow on slope land, are applied as so-called bioenergy and oil forests for liquid

Metal working oils. Cutting oils, rolling oils, quenching oils, rust preventive oils; Kinzoku kakoyu. Sessakuyu, atsuenyu, yakiireyu, boseiyu

Energy Technology Data Exchange (ETDEWEB)

Koyama, S. [Idemitsu Kosan Co. Ltd., Tokyo (Japan)

1996-04-01

With the demand against complicating working techniques for a background, foundations of the consideration for each of the lubricants in future are outlined. 1. Cutting oils: From the standpoint of speeding up and fireproofing, share of water-soluble type has come up to 30-40%. In this type, emulsifying dispersants and preservatives are combined. 2. Rolling oils: According to thinning of the standard thickness of steel plates, pressure of contacting surfaces has come up to 300 kg/mm{sup 2}(max.) and slip speed has increased too. In stainless steel plates, in order to get rid of the heat-streak (baking streak originated from wearing-out of oil film) shifting from neat oil to emulsion type is required. 3. Quenching oils: Following two systems are recent tendencies, the mineral oil system having excellent thermostability or the water system containing polyalkylneglycol etc., but the latter is expected from the viewpoint of fireproofing. 4. Rust preventive oils: As this oils do not aim at the rust prevention for long term, degreasing property is required. 20 refs., 5 figs., 1 tab.

Preliminary studies of epoxidized palm oil as sizing chemical for carbon fibers

International Nuclear Information System (INIS)

Salleh, S.N.M.; Ubaidillah, E.A.E.; Abidin, M.F.Z.

2010-01-01

Epoxidized palm oil is derived from palm oil through chemical reaction with peracetic acid. Preliminary studies to coat carbon fibers have shown promising result towards applying natural product in carbon fibre composites. Mechanical studies of sized carbon fibers with epoxidized palm oil showed significant increase in tensile and interfacial shear strength. Surface morphology of sized or coated carbon fibers with epoxidized palm oil reveals clear increase in root means square-roughness (RMS). This indicates the change of the surface topography due to sized or coated carbon fibers with epoxidized palm oil. (author)

Effect of fluorescent light on quality and stability of edible fats and oils

International Nuclear Information System (INIS)

Ahmed, T.; Atta, S.; Sohail, M.; Khan, A.R.; Akhter, S.

2011-01-01

Photo oxidative stress were applied to commonly consumed edible oil and fat i.e., animal fat (AF), vanaspati ghee (VG), sunflower oil (SFO), desi ghee (DG), rapeseed oil (RSO), soybean oil (SBO) as well as sea buckthorn seed oil (SB Seed oil) and sea buckthorn pulp oil (SB Pulp oil). The changes in their quality parameters i.e. free fatty acid (FFA), peroxide value (POV), beta-carotene and color (OD) were determined. Photo oxidative stress significantly (p < 0.05) increased the FFA, POV and OD, however, concentration of beta carotene decreased in all the samples with the increase in storage time. The Sea buckthorn oil was found to be more stable than other oils owing to the presence of tocopherol contents and beta-carotene. (author)

Optimization of Refining Craft for Vegetable Insulating Oil

Science.gov (United States)

Zhou, Zhu-Jun; Hu, Ting; Cheng, Lin; Tian, Kai; Wang, Xuan; Yang, Jun; Kong, Hai-Yang; Fang, Fu-Xin; Qian, Hang; Fu, Guang-Pan

2016-05-01

Vegetable insulating oil because of its environmental friendliness are considered as ideal material instead of mineral oil used for the insulation and the cooling of the transformer. The main steps of traditional refining process included alkali refining, bleaching and distillation. This kind of refining process used in small doses of insulating oil refining can get satisfactory effect, but can't be applied to the large capacity reaction kettle. This paper using rapeseed oil as crude oil, and the refining process has been optimized for large capacity reaction kettle. The optimized refining process increases the acid degumming process. The alkali compound adds the sodium silicate composition in the alkali refining process, and the ratio of each component is optimized. Add the amount of activated clay and activated carbon according to 10:1 proportion in the de-colorization process, which can effectively reduce the oil acid value and dielectric loss. Using vacuum pumping gas instead of distillation process can further reduce the acid value. Compared some part of the performance parameters of refined oil products with mineral insulating oil, the dielectric loss of vegetable insulating oil is still high and some measures are needed to take to further optimize in the future.

Exploring for oil with nuclear physics

Directory of Open Access Journals (Sweden)

Mauborgne Marie-Laure

2017-01-01

Full Text Available Oil↓eld service companies help identify and assess reserves and future production for oil and gas reservoirs, by providing petrophysical information on rock formations. Some parameters of interest are the fraction of pore space in the rock, the quantity of oil or gas contained in the pores, the lithology or composition of the rock matrix, and the ease with which 'uids 'ow through the rock, i.e. its permeability. Downhole logging tools acquire various measurements based on electromagnetic, acoustic, magnetic resonance and nuclear physics to determine properties of the subsurface formation surrounding the wellbore. This introduction to nuclear measurements applied in the oil and gas industry reviews the most advanced nuclear measurements currently in use, including capture and inelastic gamma ray spectroscopy, neutron-gamma density, thermal neutron capture cross section, natural gamma ray, gamma-gamma density, and neutron porosity. A brief description of the technical challenges associated with deploying nuclear technology in the extreme environmental conditions of an oil well is also presented.

Exploring for oil with nuclear physics

Science.gov (United States)

Mauborgne, Marie-Laure; Allioli, Françoise; Stoller, Chris; Evans, Mike; Manclossi, Mauro; Nicoletti, Luisa

2017-09-01

Oil↓eld service companies help identify and assess reserves and future production for oil and gas reservoirs, by providing petrophysical information on rock formations. Some parameters of interest are the fraction of pore space in the rock, the quantity of oil or gas contained in the pores, the lithology or composition of the rock matrix, and the ease with which 'uids 'ow through the rock, i.e. its permeability. Downhole logging tools acquire various measurements based on electromagnetic, acoustic, magnetic resonance and nuclear physics to determine properties of the subsurface formation surrounding the wellbore. This introduction to nuclear measurements applied in the oil and gas industry reviews the most advanced nuclear measurements currently in use, including capture and inelastic gamma ray spectroscopy, neutron-gamma density, thermal neutron capture cross section, natural gamma ray, gamma-gamma density, and neutron porosity. A brief description of the technical challenges associated with deploying nuclear technology in the extreme environmental conditions of an oil well is also presented.

Oil demand asymmetry in the OECD

International Nuclear Information System (INIS)

Shealy, M.T.

1990-01-01

Oil demand asymmetry exists, is significant, and can be captured with a simple demand equation using a Pmax term. The unstable parameters of the original symmetric equations suggest misspecification. Addition of a Pmax term to represent asymmetry yields stable parameters from 1982 through 1989 and so suggests proper specification. Asymmetry is significant because the short-run (and long-run) price elasticity is less than half as large when oil price falls as when price rises beyond the past peak. The lower elasticity applies both to price decreases and also to price increases for which price remains below the past peak. As long as the real oil price remains well below the 1981 peak, asymmetry implies that OECD oil demand should be less sensitive to oil price variations than in 1981. More specifically, the results shown suggest that today's oil demand elasticity should be less than half as large as the elasticity for a price increase in 1981. Forecasts from the asymmetric equations are significantly higher than the DOE base-case forecast. DOE's lower forecast is due to greater price asymmetry through 1995 and to higher long-run price elasticity beyond 1995. One reason for the higher long-run price elasticity might be greater assumed improvements in energy-efficiency than implied by the historical data

Waxy crude oil flow restart ability

Energy Technology Data Exchange (ETDEWEB)

Sierra, Andre Gaona; Varges, Priscilla Ribeiro; Mendes, Paulo Roberto de Souza [Dept. of Mechanical Engineering. Pontificia Universidade Catolica do Rio de Janeiro, RJ (Brazil)], e-mails: prvarges@puc-rio.br, pmendes@puc-rio.br; Ziglio, Claudio [PETROBRAS S.A, R.J., Rio de Janeiro, RJ (Brazil)], e-mail: ziglio@petrobras.com.br

2010-07-01

Under the hot reservoir conditions, waxy crudes behave like Newtonian fluids but once they experience very cold temperatures on the sea floor, the heavy paraffin's begin to precipitate from the solution impacting non- Newtonian flow behavior to the crude (Chang 2000, Lee 2009, Davidson 2004) and begin to deposit on the pipe wall leave blocked of pipeline. This gel cannot be broken with the original steady state flow operating pressure applied before gelation (Chang 1998). Restarting waxy crude oil flows in pipelines is a difficult issue because of the complex rheological behavior of the gelled oil. Indeed, below the WAT, the gelled oil exhibits viscoplastic, thixotropic, temperature-dependent, and compressible properties due to the interlocking gel-like structure formed by the crystallized paraffin compounds and the thermal shrinkage of the oil. The main objective of this work is to determine the minimal pressure to restart the flow, and the relationship between the fluid rheology , pipe geometry and the restart pressure of the flow. Experiments will be performed to investigate the displacement of carbopol aqueous solutions (viscoplastic fluid without thixotropic effects) by Newtonian oil flowing through a strait pipe to validate the experimental apparatus. Therefore, tests will be made with different fluids, like Laponite and waxy crude oils. (author)

Review on biofuel oil and gas production processes from microalgae

International Nuclear Information System (INIS)

Amin, Sarmidi

2009-01-01

Microalgae, as biomass, are a potential source of renewable energy, and they can be converted into energy such as biofuel oil and gas. This paper presents a brief review on the main conversion processes of microalgae becoming energy. Since microalgae have high water content, not all biomass energy conversion processes can be applied. By using thermochemical processes, oil and gas can be produced, and by using biochemical processes, ethanol and biodiesel can be produced. The properties of the microalgae product are almost similar to those of offish and vegetable oils, and therefore, it can be considered as a substitute of fossil oil.

What drives the formation of global oil trade patterns?

International Nuclear Information System (INIS)

Zhang, Hai-Ying; Ji, Qiang; Fan, Ying

2015-01-01

In this paper, the spatial characteristics of current global oil trade patterns are investigated by proposing a new indicator Moran-F. Meanwhile, the factors that influence the formation of oil trade patterns are identified by constructing four different kinds of spatial econometric models. The findings indicate that most oil exporters have an obvious export focus in North America and a relatively balanced export in Europe and the Asia-Pacific region. Besides supply and demand factors, technological progress and energy efficiency have also significantly influenced the oil trade. Moreover, there is a spillover effect of trade flow among different regions, but its impact is weak. In addition, oil importers in the same region have the potential to cooperate due to their similar import sources. Finally, promotion of oil importers' R&D investments can effectively reduce the demand for global oil trade. - Highlights: • A new spatial association Moran-F indicator that applies to trade flows is proposed. • Driving factors affecting the formation of oil trade patterns are identified. • Oil-exporting countries implement various export strategies in different regions. • Supply, demand and technological factors contribute to the oil trade patterns. • Spillover effect of each factor affecting oil trade flows does exist but is limited

Generation and migration of Bitumen and oil from the oil shale interval of the Eocene Green River formation, Uinta Basin, Utah

Science.gov (United States)

Johnson, Ronald C.; Birdwell, Justin E.; Mercier, Tracey J.

2016-01-01

The results from the recent U.S. Geological Survey assessment of in-place oil shale resources of the Eocene Green River Formation, based primarily on the Fischer assay method, are applied herein to define areas where the oil shale interval is depleted of some of its petroleum-generating potential along the deep structural trough of the basin and to make: (1) a general estimates of the amount of this depletion, and (2) estimate the total volume of petroleum generated. Oil yields (gallons of oil per ton of rock, GPT) and in-place oil (barrels of oil per acre, BPA) decrease toward the structural trough of the basin, which represents an offshore lacustrine area that is believed to have originally contained greater petroleum-generating potential than is currently indicated by measured Fischer assay oil yields. Although this interval is considered to be largely immature for oil generation based on vitrinite reflectance measurements, the oil shale interval is a likely source for the gilsonite deposits and much of the tar sands in the basin. Early expulsion of petroleum may have occurred due to the very high organic carbon content and oil-prone nature of the Type I kerogen present in Green River oil shale. In order to examine the possible sources and migration pathways for the tar sands and gilsonite deposits, we have created paleogeographic reconstructions of several oil shale zones in the basin as part of this study.

Closed Process of Shale Oil Recovery from Circulating Washing Water by Hydrocyclones

Directory of Open Access Journals (Sweden)

Yuan Huang

2016-12-01

Full Text Available The conventional oil recovery system in the Fushun oil shale retorting plant has a low oil recovery rate. A large quantity of fresh water is used in the system, thereby consuming a considerable amount of water and energy, as well as polluting the environment. This study aims to develop a closed process of shale oil recovery from the circulating washing water for the Fushun oil shale retorting plant. The process would increase oil yield and result in clean production. In this process, oil/water hydrocyclone groups were applied to decrease the oil content in circulating water and to simultaneously increase oil yield. The oil sludge was removed by the solid/liquid hydrocyclone groups effectively, thereby proving the smooth operation of the devices and pipes. As a result, the oil recovery rate has increased by 5.3 %, which corresponds to 230 tonnes a month.

Larvicidal activity of Neem oil and three plant essential oils from Senegal against Chrysodeixis chalcites (Esper, 1789

Directory of Open Access Journals (Sweden)

Saliou Ngom

2018-01-01

Full Text Available Objective: To evaluate the insecticide, larvicidal and repellent activity of the essential oils from Callistemon viminalis, Melaleuca leucadendron, and Hyptis suaveolens against Chrysodeixis chalcites and to compare it with neem oil (Azadirachta indica. Methods: The essential oils of the leaves of these aromatiques plants were extracted by steam distillation and contacts tests were carried out. Results: Essential oils in ethanol from Callistemon viminalis showed a higher biological activity than the neem with 100% larval mortality at the concentration of 2 μg/mL for 6 h, 100% and 90% in ethanol from Melaleuca leucadendron and Hyptis suaveolens, respectively at the concentration of 4 μg/mL for 24 h. By inhalation, the essential oils from Melaleuca leucadendron and of Hyptis suaveolens were more effective with mortality rates of larvae 100% and 50% respectively at 2 μg/L air applied after 24 h. Nevertheless, the neem has shown to be a repulsive plant and anti-nutritional plant. A significant difference in the percentages of consumption between leaves treated with neem oil and the control samples was observed (Newman-Keuls test except for Melaleuca leucadendron. Conclusions: The results of the study highlight remarkable biocide, properties of tested extracts, which provides important opportunities for the development of biopesticides.

Detection of Adulterated Vegetable Oils Containing Waste Cooking Oils Based on the Contents and Ratios of Cholesterol, β-Sitosterol, and Campesterol by Gas Chromatography/Mass Spectrometry.

Science.gov (United States)

Zhao, Haixiang; Wang, Yongli; Xu, Xiuli; Ren, Heling; Li, Li; Xiang, Li; Zhong, Weike

2015-01-01

A simple and accurate authentication method for the detection of adulterated vegetable oils that contain waste cooking oil (WCO) was developed. This method is based on the determination of cholesterol, β-sitosterol, and campesterol in vegetable oils and WCO by GC/MS without any derivatization. A total of 148 samples involving 12 types of vegetable oil and WCO were analyzed. According to the results, the contents and ratios of cholesterol, β-sitosterol, and campesterol were found to be criteria for detecting vegetable oils adulterated with WCO. This method could accurately detect adulterated vegetable oils containing 5% refined WCO. The developed method has been successfully applied to multilaboratory analysis of 81 oil samples. Seventy-five samples were analyzed correctly, and only six adulterated samples could not be detected. This method could not yet be used for detection of vegetable oils adulterated with WCO that are used for frying non-animal foods. It provides a quick method for detecting adulterated edible vegetable oils containing WCO.

Biodegradation of petroleum oil by certain bacterial strains

International Nuclear Information System (INIS)

Zakaria, A.E.M.

1998-01-01

Balaeam base oil was chosen as a model oil in the present study through which some abiotic treatments were implemented aiming at attenuating its naphthenic and aromatic contents; such as the adsorptive technique and the gamma-irradiation technique . In an attempt to apply the biodegrading bacteria as oil pollutant bio indicators upon coastal water samples, a correlation between hydrocarbon concentration and the relative enumeration of the bacterial oil degraders was detected for some litter locations along the mediterranean Sea shore west and east Delta, Suez canal. and suez gulf. 24 petroleum utilizing bacterial isolates were isolated from El-Zayteia port (suez) and identified by morphological, physiological and environmental examination . the biodegradation capacity of the isolates towards the chosen model oil and its separate components was studied in comparison with the standard isolate pseudomonas aeruginosa. Further, the role of the bacterial plasmids taking part in the biodegradation process was investigated as well

Interval ridge regression (iRR) as a fast and robust method for quantitative prediction and variable selection applied to edible oil adulteration.

Science.gov (United States)

Jović, Ozren; Smrečki, Neven; Popović, Zora

2016-04-01

A novel quantitative prediction and variable selection method called interval ridge regression (iRR) is studied in this work. The method is performed on six data sets of FTIR, two data sets of UV-vis and one data set of DSC. The obtained results show that models built with ridge regression on optimal variables selected with iRR significantly outperfom models built with ridge regression on all variables in both calibration (6 out of 9 cases) and validation (2 out of 9 cases). In this study, iRR is also compared with interval partial least squares regression (iPLS). iRR outperfomed iPLS in validation (insignificantly in 6 out of 9 cases and significantly in one out of 9 cases for poil, a well known health beneficial nutrient, is studied in this work by mixing it with cheap and widely used oils such as soybean (So) oil, rapeseed (R) oil and sunflower (Su) oil. Binary mixture sets of hempseed oil with these three oils (HSo, HR and HSu) and a ternary mixture set of H oil, R oil and Su oil (HRSu) were considered. The obtained accuracy indicates that using iRR on FTIR and UV-vis data, each particular oil can be very successfully quantified (in all 8 cases RMSEPoil (R(2)>0.99). Copyright © 2015 Elsevier B.V. All rights reserved.

Oil vulnerability index of oil-importing countries

International Nuclear Information System (INIS)

Gupta, Eshita

2008-01-01

This paper assesses the relative oil vulnerability of 26 net oil-importing countries for the year 2004 on the basis of various indicators - the ratio of value of oil imports to gross domestic product (GDP), oil consumption per unit of GDP, GDP per capita and oil share in total energy supply, ratio of domestic reserves to oil consumption, exposure to geopolitical oil market concentration risks as measured by net oil import dependence, diversification of supply sources, political risk in oil-supplying countries, and market liquidity. The approach using the principal component technique has been adopted to combine these individual indicators into a composite index of oil vulnerability. Such an index captures the relative sensitivity of various economies towards developments of the international oil market, with a higher index indicating higher vulnerability. The results show that there are considerable differences in the values of individual indicators of oil vulnerability and overall oil vulnerability index among the countries (both inter and intraregional). (author)

Oil vulnerability index of oil-importing countries

Energy Technology Data Exchange (ETDEWEB)

Gupta, Eshita [The Energy and Resources Institute, Darbari Seth Block, Habitat Place, New Delhi 110 003 (India)

2008-03-15

This paper assesses the relative oil vulnerability of 26 net oil-importing countries for the year 2004 on the basis of various indicators - the ratio of value of oil imports to gross domestic product (GDP), oil consumption per unit of GDP, GDP per capita and oil share in total energy supply, ratio of domestic reserves to oil consumption, exposure to geopolitical oil market concentration risks as measured by net oil import dependence, diversification of supply sources, political risk in oil-supplying countries, and market liquidity. The approach using the principal component technique has been adopted to combine these individual indicators into a composite index of oil vulnerability. Such an index captures the relative sensitivity of various economies towards developments of the international oil market, with a higher index indicating higher vulnerability. The results show that there are considerable differences in the values of individual indicators of oil vulnerability and overall oil vulnerability index among the countries (both inter and intraregional). (author)

Worldwide cheap and heavy oil productions: A long-term energy model

International Nuclear Information System (INIS)

Guseo, Renato

2011-01-01

Crude oil, natural gas liquids, heavy oils, deepwater oils, and polar oils are non-renewable energy resources with increasing extraction costs. Two major definitions emerge: regular or 'cheap' oil and non-conventional or 'heavy' oil. Peaking time in conventional oil production has been a recent focus of debate. For two decades, non-conventional oils have been mixed with regular crude oil. Peaking time estimation and the rate at which production may be expected to decline, following the peak, are more difficult to determine. We propose a two-wave model for world oil production pattern and forecasting, based on the diffusion of innovation theories: a sequential multi-Bass model. Historical well-known shocks are confirmed, and new peaking times for crude oil and mixed oil are determined with corresponding depletion rates. In the final section, possible ties between the dynamics of oil extraction and refining capacities are discussed as a predictive symptom of an imminent mixed oil peak in 2016. - Highlights: → Production of conventional and non-conventional oils in aggregate time series. → Decomposition modelling and forecasting with a multi-regime model. → Diffusion of innovation theories and appropriateness of applying Bass concepts to the extraction of oil resources. → Partially overlapping oil extraction processes. → Refining capacities and dynamics of oil extraction.

Photocatalytic Desulfurization of Waste Tire Pyrolysis Oil

Directory of Open Access Journals (Sweden)

Napida Hinchiranan

2011-11-01

Full Text Available Waste tire pyrolysis oil has high potential to replace conventional fossil liquid fuels due to its high calorific heating value. However, the large amounts of sulfurous compounds in this oil hinders its application. Thus, the aim of this research was to investigate the possibility to apply the photo-assisted oxidation catalyzed by titanium dioxide (TiO2, Degussa P-25 to partially remove sulfurous compounds in the waste tire pyrolysis oil under milder reaction conditions without hydrogen consumption. A waste tire pyrolysis oil with 0.84% (w/w of sulfurous content containing suspended TiO2 was irradiated by using a high-pressure mercury lamp for 7 h. The oxidized sulfur compounds were then migrated into the solvent-extraction phase. A maximum % sulfur removal of 43.6% was achieved when 7 g/L of TiO2 was loaded into a 1/4 (v/v mixture of pyrolysis waste tire oil/acetonitrile at 50 °C in the presence of air. Chromatographic analysis confirmed that the photo-oxidized sulfurous compounds presented in the waste tire pyrolysis oil had higher polarity, which were readily dissolved and separated in distilled water. The properties of the photoxidized product were also reported and compared to those of crude oil.

When Will Occur the Crude Oil Bubbles?

International Nuclear Information System (INIS)

Su, Chi-Wei; Li, Zheng-Zheng; Chang, Hsu-Ling; Lobonţ, Oana-Ramona

2017-01-01

In this paper, we apply a recursive unit root test to investigate whether there exist multiple bubbles in crude oil price. The method is best suited for a practical implementation of a time series and delivers a consistent date-stamping strategy for the origination and termination of multiple bubbles. The empirical result indicates that there exist six bubbles during 1986–2016 when the oil price deviate from its intrinsic value based on market fundamentals. Specifically, oil price contains the fundamentals and bubble components. The dates of the bubbles correspond to specific events in the politics and financial markets. The authorities should actively fight speculative bubbles or just observe their evolutions and speculation activities may decrease, which is favour of the stabilisation of the staple commodities including crude oil price. These findings have important economic and policy implications to recognise the cause of bubbles and take corresponding measures to reduce the impact on the real economy cause of the fluctuation of crude oil price. - Highlights: • Investigate multiple bubbles in crude oil price. • Indicate six bubbles deviate from its intrinsic value based on market fundamentals. • The bubbles correspond to specific events in the politics and financial markets. • Reduce the impact on the real economy cause of the fluctuation of crude oil price.

Study of jojoba oil aging by FTIR.

Science.gov (United States)

Le Dréau, Y; Dupuy, N; Gaydou, V; Joachim, J; Kister, J

2009-05-29

As the jojoba oil was used in cosmetic, pharmaceutical, dietetic food, animal feeding, lubrication, polishing and bio-diesel fields, it was important to study its aging at high temperature by oxidative process. In this work a FT-MIR methodology was developed for monitoring accelerate oxidative degradation of jojoba oils. Principal component analysis (PCA) was used to differentiate various samples according to their origin and obtaining process, and to differentiate oxidative conditions applied on oils. Two spectroscopic indices were calculated to report simply the oxidation phenomenon. Results were confirmed and deepened by multivariate curve resolution-alternative least square method (MCR-ALS). It allowed identifying chemical species produced or degraded during the thermal treatment according to a SIMPLISMA pretreatment.

Giant Oil Fields - The Highway to Oil: Giant Oil Fields and their Importance for Future Oil Production

International Nuclear Information System (INIS)

Robelius, Fredrik

2007-01-01

Since the 1950s, oil has been the dominant source of energy in the world. The cheap supply of oil has been the engine for economic growth in the western world. Since future oil demand is expected to increase, the question to what extent future production will be available is important. The belief in a soon peak production of oil is fueled by increasing oil prices. However, the reliability of the oil price as a single parameter can be questioned, as earlier times of high prices have occurred without having anything to do with a lack of oil. Instead, giant oil fields, the largest oil fields in the world, can be used as a parameter. A giant oil field contains at least 500 million barrels of recoverable oil. Only 507, or 1 % of the total number of fields, are giants. Their contribution is striking: over 60 % of the 2005 production and about 65 % of the global ultimate recoverable reserve (URR). However, giant fields are something of the past since a majority of the largest giant fields are over 50 years old and the discovery trend of less giant fields with smaller volumes is clear. A large number of the largest giant fields are found in the countries surrounding the Persian Gulf. The domination of giant fields in global oil production confirms a concept where they govern future production. A model, based on past annual production and URR, has been developed to forecast future production from giant fields. The results, in combination with forecasts on new field developments, heavy oil and oil sand, are used to predict future oil production. In all scenarios, peak oil occurs at about the same time as the giant fields peak. The worst-case scenario sees a peak in 2008 and the best-case scenario, following a 1.4 % demand growth, peaks in 2018

Measurements of density profile evolution during the stably-stratified filling of an open enclosure

International Nuclear Information System (INIS)

Tarawneh, Constantine M.; Homan, K.O.

2008-01-01

The stably-stratified filling of an open enclosure produces an interfacial gradient layer which is transported through the enclosure with the bulk flow. The evolution of this interfacial layer is strongly time-dependent and is driven by the nature of the interaction between the internal gravity waves and the inlet-driven interfacial shear. Measurements of density profile evolution have been completed for a rectangular enclosure with a single corner inlet and density variation produced by saline concentration. This system serves as a mass transfer analog to large-scale, thermally-stratified energy storage devices, preserving dynamic similitude in a laboratory-scale system. The experiments covered jet Reynolds numbers of 200-2200 and Froude numbers of 0.06-0.6 in an enclosure with a width 23 times the jet inlet height. The density profiles are seen to be strongly asymmetric and exhibit growth rates significantly different than due to simple one-dimensional molecular diffusion. In addition, shadowgraph and hydrogen bubble visualizations of the density and velocity fields in the gradient layer show the persistence of complex multi-dimensional flow structure even at relatively late stages of the filling process when the gradient layer has been transported well away from the enclosure inlet. The evolution of the vertical density profile has been compared quantitatively to a quasi one-dimensional model based upon empirical diffusivity coefficients

Hubbert's Peak: the Impending World oil Shortage

Science.gov (United States)

Deffeyes, K. S.

2004-12-01

Global oil production will probably reach a peak sometime during this decade. After the peak, the world's production of crude oil will fall, never to rise again. The world will not run out of energy, but developing alternative energy sources on a large scale will take at least 10 years. The slowdown in oil production may already be beginning; the current price fluctuations for crude oil and natural gas may be the preamble to a major crisis. In 1956, the geologist M. King Hubbert predicted that U.S. oil production would peak in the early 1970s.1 Almost everyone, inside and outside the oil industry, rejected Hubbert's analysis. The controversy raged until 1970, when the U.S. production of crude oil started to fall. Hubbert was right. Around 1995, several analysts began applying Hubbert's method to world oil production, and most of them estimate that the peak year for world oil will be between 2004 and 2008. These analyses were reported in some of the most widely circulated sources: Nature, Science, and Scientific American.2 None of our political leaders seem to be paying attention. If the predictions are correct, there will be enormous effects on the world economy. Even the poorest nations need fuel to run irrigation pumps. The industrialized nations will be bidding against one another for the dwindling oil supply. The good news is that we will put less carbon dioxide into the atmosphere. The bad news is that my pickup truck has a 25-gallon tank.

Evaluation of Sebostatic Activity of Juniperus communis Fruit Oil and Pelargonium graveolens Oil Compared to Niacinamide

Directory of Open Access Journals (Sweden)

Justyna Kozlowska

2017-09-01

Full Text Available As a facial skin condition, oily skin causes cosmetic problems, such as large pores, shiny appearance, and the feeling of greasiness and heaviness. Furthermore, extensive sebum production leads to common skin disorders such as acne vulgaris or seborrheic dermatitis. This study investigated the efficacy of sebum control tonics containing Juniperus communis fruit oil, Pelargonium graveolens oil, or niacinamide. The effects of Juniperus communis fruit oil, Pelargonium graveolens oil, and niacinamide on sebum excretion rates were investigated using Sebumeter®. Sebum measurements (Sebumeter® SM 815, Courage & Khazaka®, Köln, Germany were made on the skin surface in three places by applying the sebumeter probe to the forehead after 10, 60, and 120 min from application of the tonic. The results indicated that the application of the tonic maintained a lower sebum secretion 10 min and 60 min after the application of the cosmetic, compared to those before it. However, a visible sebum-reducing efficacy after 2 h was reported only for tonic containing 0.25% Pelargonium graveolens oil and for the tonic with the addition of 3% niacinamide. After 2 h, the values of sebum measurements were 44 ± 5.13 a.u. and 58 ± 9.07 a.u., respectively. Our results show that the tonic with the addition of 0.25% Pelargonium graveolens oil is the most effective in reducing sebum production.

Yukon's common oil and gas regime

International Nuclear Information System (INIS)

Love, B.

1998-01-01

The Yukon's common oil and gas regime was developed in partnership with First Nations and it sets out the rules that will apply throughout the Yukon and on Yukon and First Nation lands. While separate and distinct, it conforms with and is compatible with other government systems and regimes. The major elements of the common regime include the Oil and Gas Act, regulations, policies, processes and agreements. The specific opportunities that are available in each phase of oil and gas development in the Yukon are described, with a map showing all basins, reserves and sites of current oil and gas activity. The Yukon has eight potential oil and gas basins: North Coast, Old Crow, Kandik, Eagle Plain, Peel Plateau, Bonnet Plume, Whitehorse Trough, and Liard Plateau. Only three of the eight, the Liard Plateau, Whitehorse Trough and Eagle Plain, have been explored. No wells have been drilled in several of Yukon's basins. Factors influencing economic opportunities in the Territory are also described, including: (1) international events and energy markets, (2) North American gas markets, (3) environmental factors, (4) competitiveness of the Yukon regime, and (5) the commitment of industry resources. 4 figs

Potential of Eucalyptus Oil as Repellent against House Rat, Rattus rattus

Science.gov (United States)

Thind, Ramandeep Kaur; Mahal, Amrit Kaur

2014-01-01

Rodent repellents are chemicals which by taste or odour or possibly by both will prevent animal from feeding or gnawing. Such substances may be used in protecting an area from rodent infestation or in protecting packaged food, packing materials, electric cables, and other important vulnerable materials. Mature and healthy house rat, Rattus rattus of both sexes, was exposed to 5, 10, and 20% eucalyptus oil applied as spray in laboratory pens in bichoice tests. Each concentration was applied through three different modes of application, that is, daily, once, and alternatively in a week. Repellent effect of the oil was assessed based on food consumption from treated and untreated sides for four days. In overall, food consumption was significantly (P eucalyptus oil. Present studies reveal the potential of eucalyptus oil in repelling away R. rattus; however, further studies may be conducted to enhance the persistence of repellent effect for longer period of time. PMID:24523633

Selective separation of oil and water with mesh membranes by capillarity

KAUST Repository

Yu, Yuanlie; Chen, Hua; Liu, Yun; Craig, Vincent S.J.; Lai, Zhiping

2016-01-01

The separation of oil and water from wastewater generated in the oil-production industries, as well as in frequent oil spillage events, is important in mitigating severe environmental and ecological damage. Additionally, a wide arrange of industrial processes require oils or fats to be removed from aqueous systems. The immiscibility of oil and water allows for the wettability of solid surfaces to be engineered to achieve the separation of oil and water through capillarity. Mesh membranes with extreme, selective wettability can efficiently remove oil or water from oil/water mixtures through a simple filtration process using gravity. A wide range of different types of mesh membranes have been successfully rendered with extreme wettability and applied to oil/water separation in the laboratory. These mesh materials have typically shown good durability, stability as well as reusability, which makes them promising candidates for an ever widening range of practical applications. © 2016 Elsevier B.V.

Selective separation of oil and water with mesh membranes by capillarity

KAUST Repository

Yu, Yuanlie

2016-05-29

The separation of oil and water from wastewater generated in the oil-production industries, as well as in frequent oil spillage events, is important in mitigating severe environmental and ecological damage. Additionally, a wide arrange of industrial processes require oils or fats to be removed from aqueous systems. The immiscibility of oil and water allows for the wettability of solid surfaces to be engineered to achieve the separation of oil and water through capillarity. Mesh membranes with extreme, selective wettability can efficiently remove oil or water from oil/water mixtures through a simple filtration process using gravity. A wide range of different types of mesh membranes have been successfully rendered with extreme wettability and applied to oil/water separation in the laboratory. These mesh materials have typically shown good durability, stability as well as reusability, which makes them promising candidates for an ever widening range of practical applications. © 2016 Elsevier B.V.

Oil sands geologists in an industry-school partnership : a resource and teaching opportunity

International Nuclear Information System (INIS)

Dudley, J.S.; Doram, T.

1999-01-01

The province of Alberta has developed a credit course within their Career and Technology Studies Program on the earth science of oil sands for senior high school science students. The course helps students learn to apply basic sciences to earth science through workplace site visits, resource material and team work. This paper described the increasing demand for, and success of, industry-high school partnerships, and provided special emphasis on the Bowness Senior High School-Imperial Oil partnership in Calgary, Alberta. Imperial Oil Resources is a major producer of oil sands and an employer of earth scientists in a variety of careers in which a wide range of technologies is applied. Students enrolled in the credit study program visit the Imperial Oil Resources Research Centre on five different occasions to gain skills and qualities sought by the workplace including communication, adaptability, team work, and science literacy and its application. 9 refs., 1 tab., 2 figs

They say coconut oil can aid weight loss, but can it really?

Science.gov (United States)

Clegg, M E

2017-10-01

There has in recent years, been much media speculation and consumer interest in the beneficial satiating properties of consuming coconut oil and its potential to aid weight loss. However, the media has primarily cited studies using medium-chain triglycerides (MCT) oil. The current perspective looks at the research that is available on coconut oil. It examines if and how MCT-related research can be applied to coconut oil and if there is potential for coconut oil to aid weight loss. The current report indicates a lack of consistent evidence on the topic of coconut oil, satiety and weight loss. Given both the publicity and the increased consumption of coconut oil further research, particularly long-term clinical trials, in this area are warranted.

Impact of essential oils on mycelial growth of Botrytis cinerea

Directory of Open Access Journals (Sweden)

Slavko Grgić

2016-12-01

Full Text Available The aim of this study was to determine the effect of 22 essential oils (anise, thyme, cumin, peppermint, lavender, sage, lemon balm, rosemary, myrtle, cinnamon leaf, basil, white pine, eucalyptus, cedar, bergamot, mandarin, cypress, patchouli, ginger, bitter orange, sandalwood, camphor on the growth of gray mold fungus Botrytis cinerea. The experiment was performed in vitro on PDA medium in 2 repetitions. Oils were applied in three amounts (3, 5 and 7 μl, and the mycelial growth was measured after three and nine days of incubation. All oils, except oils of bitter orange, sandalwood and camphor, have shown a certain antifungal activity. Compared to the water control, thyme and anise oil have shown the best antifungal activity, while for oils of bitter orange, sandalwood and camphor a stimulating effect on a growth of fungus B. cinerea was determined.

Thermal Diffusivity Measurements in Edible Oils using Transient Thermal Lens

Science.gov (United States)

Valdez, R. Carbajal.; Pérez, J. L. Jiménez.; Cruz-Orea, A.; Martín-Martínez, E. San.

2006-11-01

Time resolved thermal lens (TL) spectrometry is applied to the study of the thermal diffusivity of edible oils such as olive, and refined and thermally treated avocado oils. A two laser mismatched-mode experimental configuration was used, with a He Ne laser as a probe beam and an Ar+ laser as the excitation one. The characteristic time constant of the transient thermal lens was obtained by fitting the experimental data to the theoretical expression for a transient thermal lens. The results showed that virgin olive oil has a higher thermal diffusivity than for refined and thermally treated avocado oils. This measured thermal property may contribute to a better understanding of the quality of edible oils, which is very important in the food industry. The thermal diffusivity results for virgin olive oil, obtained from this technique, agree with those reported in the literature.

Fuel oil systems for standby diesel-generators

International Nuclear Information System (INIS)

Anon.

1976-01-01

This Standard provides the design requirements for fuel oil system for diesel-generators that provide standby power for a nuclear power generating station. The system includes all essential equipment from and including fuel oil storage tanks up to the terminal connection on the diesel-engine. It does not include that portion of the fuel oil system supplied by the diesel-generator manufacturer which is in accordance with Trial-Use Criteria for Diesel-Generator Units Applied as Standby Power Supplies for Nuclear Power Generating Stations, IEEE-387-1972. This definition of scope is intended to exclude only those factory-assembled, engine-mounted appurtances supplied with a diesel-generator unit. Integral tanks are, however, within the scope of this Standard. It also excludes motors, motor control centers, switchgear, cables, and other electrical equipment which is used in operation of the fuel oil system, except to define interface requirements

Application of Raman spectroscopy for direct analysis of Carlina acanthifolia subsp. utzka root essential oil.

Science.gov (United States)

Strzemski, Maciej; Wójciak-Kosior, Magdalena; Sowa, Ireneusz; Agacka-Mołdoch, Monika; Drączkowski, Piotr; Matosiuk, Dariusz; Kurach, Łukasz; Kocjan, Ryszard; Dresler, Sławomir

2017-11-01

Carlina genus plants e.g. Carlina acanthifolia subsp. utzka have been still used in folk medicine of many European countries and its biological activity is mostly associated with root essential oils. In the present paper, Raman spectroscopy (RS) was applied for the first time for evaluation of essential oil distribution in root of C. acnthifolia subsp. utzka and identification of root structures containing the essential oil. Furthermore, RS technique was applied to assess chemical stability of oil during drying of plant material or distillation process. Gas chromatography-mass spectrometry was used for qualitative and quantitative analysis of the essential oil. The identity of compounds was confirmed using Raman, ATR-IR and NMR spectroscopy. Carlina oxide was found to be the main component of the oil (98.96% ± 0.15). The spectroscopic study showed the high stability of essential oil and Raman distribution analysis indicated that the oil reservoirs were localized mostly in the structures of outer layer of the root while the inner part showed nearly no signal assigned to the oil. Raman spectroscopy technique enabled rapid, non-destructive direct analysis of plant material with minimal sample preparation and allowed straightforward, unambiguous identification of the essential oil in the sample. Copyright © 2017. Published by Elsevier B.V.

Thermal response of rat fibroblasts stably transfected with the human 70-kDa heat shock protein-encoding gene

International Nuclear Information System (INIS)

Li, G.C.; Li, Ligeng; Liu, Yunkang; Mak, J.Y.; Chen, Lili; Lee, W.M.F.

1991-01-01

The major heat shock protein hsp70 is synthesized by cells of a wide variety of organisms in response to heat shock or other environmental stresses and is assumed to play an important role in protecting cells from thermal stress. The authors have tested this hypothesis directly by transfecting a constitutively expressed recombinant human hsp70-encoding gene into rat fibroblasts and examining the relationship between the levels of human hsp70 expressed and thermal resistance of the stably transfected rat cells. Successful transfection and expression of the gene for human hsp70 were characterized by RNA hybridization analysis, low-dimensional gel electrophoresis, and immunoblot analysis. When individual cloned cell lines were exposed to 45C and their thermal survivals were determined by colony-formation assay, they found that the expression of human hsp70 conferred heat resistance to the rat cells. These results reinforce the hypothesis that hsp70 has a protective function against thermal stress

Direct Detection of Oil; Case History From Iran

International Nuclear Information System (INIS)

Tabatabaee, S. H.

2007-01-01

Iran is one of the main petroleum producers and also one of the countries which experiences contemporary geophysical techniques in Middle East region. Main aim of this study is direct detection of oil hydrocarbons by a special geophysical technique. To accomplish that, FEM, TEM and IP integrated geophysical techniques were successfully applied to measure IP phase shift which might relate to existence of oil traps. Target penetration for this prospecting is about 6 kms

Early warning model based on correlated networks in global crude oil markets

Science.gov (United States)

Yu, Jia-Wei; Xie, Wen-Jie; Jiang, Zhi-Qiang

2018-01-01

Applying network tools on predicting and warning the systemic risks provides a novel avenue to manage risks in financial markets. Here, we construct a series of global crude oil correlated networks based on the historical 57 oil prices covering a period from 1993 to 2012. Two systemic risk indicators are constructed based on the density and modularity of correlated networks. The local maximums of the risk indicators are found to have the ability to predict the trends of oil prices. In our sample periods, the indicator based on the network density sends five signals and the indicator based on the modularity index sends four signals. The four signals sent by both indicators are able to warn the drop of future oil prices and the signal only sent by the network density is followed by a huge rise of oil prices. Our results deepen the application of network measures on building early warning models of systemic risks and can be applied to predict the trends of future prices in financial markets.

Miscible fluid displacement: an answer to increasing oil recovery

Energy Technology Data Exchange (ETDEWEB)

Rodriguez, N R; Rivera, R J

1976-01-01

This study presents the state of the art on miscible and miscible-type processes. It is well known that when these processes are applied under ideal laboratory conditions, the oil recovery obtained from linear cores approaches 100% of the total oil contained in the porous structure which is contacted by the displacing fluids. In the past few years, a worldwide shortage of crude oil supplies produced an increased interest in new oil recovery methods. Because of this situation, the oil industry turned its eyes back toward the miscible processes. This study discusses the following miscible fluid displacement processes: (1) high-pressure dry gas displacement; (2) enriched gas displacement; (3) GLP slug flooding; and (4) carbon dioxide displacement. In addition to the processes aforementioned, this work presents the main features of the micellar solution flooding process. (17 refs.)

Essential Oils and Fragrances from Natural Sources

Indian Academy of Sciences (India)

Essential oils should be subjected to both qualitative and quan- ... Several methods are employed in modern perfumery. A perfume is a ... Three types of hydro- ..... Applied Research, Proceedings of the 27th International Symposium on.

[Near infrared spectroscopy study on water content in turbine oil].

Science.gov (United States)

Chen, Bin; Liu, Ge; Zhang, Xian-Ming

2013-11-01

Near infrared (NIR) spectroscopy combined with successive projections algorithm (SPA) was investigated for determination of water content in turbine oil. Through the 57 samples of different water content in turbine oil scanned applying near infrared (NIR) spectroscopy, with the water content in the turbine oil of 0-0.156%, different pretreatment methods such as the original spectra, first derivative spectra and differential polynomial least squares fitting algorithm Savitzky-Golay (SG), and successive projections algorithm (SPA) were applied for the extraction of effective wavelengths, the correlation coefficient (R) and root mean square error (RMSE) were used as the model evaluation indices, accordingly water content in turbine oil was investigated. The results indicated that the original spectra with different water content in turbine oil were pretreated by the performance of first derivative + SG pretreatments, then the selected effective wavelengths were used as the inputs of least square support vector machine (LS-SVM). A total of 16 variables selected by SPA were employed to construct the model of SPA and least square support vector machine (SPA-LS-SVM). There is 9 as The correlation coefficient was 0.975 9 and the root of mean square error of validation set was 2.655 8 x 10(-3) using the model, and it is feasible to determine the water content in oil using near infrared spectroscopy and SPA-LS-SVM, and an excellent prediction precision was obtained. This study supplied a new and alternative approach to the further application of near infrared spectroscopy in on-line monitoring of contamination such as water content in oil.

Sonochemical approaches to enhanced oil recovery.

Science.gov (United States)

Abramov, Vladimir O; Abramova, Anna V; Bayazitov, Vadim M; Altunina, Lyubov K; Gerasin, Artyom S; Pashin, Dmitriy M; Mason, Timothy J

2015-07-01

Oil production from wells reduces with time and the well becomes uneconomic unless enhanced oil recovery (EOR) methods are applied. There are a number of methods currently available and each has specific advantages and disadvantages depending on conditions. Currently there is a big demand for new or improved technologies in this field, the hope is that these might also be applicable to wells which have already been the subject of EOR. The sonochemical method of EOR is one of the most promising methods and is important in that it can also be applied for the treatment of horizontal wells. The present article reports the theoretical background of the developed sonochemical technology for EOR in horizontal wells; describes the requirements to the equipment needed to embody the technology. The results of the first field tests of the technology are reported. Copyright © 2014 Elsevier B.V. All rights reserved.

Preliminary Study on Treatment of Palm Oil Mill Effluent (POME by Sand Filtration-DBD Plasma System

Directory of Open Access Journals (Sweden)

Ariadi Hazmi

2016-02-01

Full Text Available In the palm oil industry, open ponding, aerobic and anaerobic digestion, physicochemical treatment and membrane filtration are generally applied as conventional treatments of palm oil mill effluent (POME. In this study, a sand filtration-dielectric barrier discharge (DBD system was investigated as an alternative process for treating POME. This system can reduce land usage, processing time and costs compared to conventional systems. The removal efficiency of chemical oxygen demand (COD, biological oxygen demand (BOD5, and oil-grease in relation to the applied voltage were studied. Furthermore, the pH and temperature profiles were investigated. The obtained results indicate that the removal efficiency of COD, BOD5, and oil-grease increased with an increase of the applied voltage. The electrical energy consumption needed is about 10.56 kWh/L of POME.

Antibody-dependent cellular cytotoxicity and cytokine/chemokine secretion by KHYG-1 cells stably expressing FcγRIIIA.

Science.gov (United States)

Kobayashi, Eiji; Motoi, Sotaro; Sugiura, Masahito; Kajikawa, Masunori; Kojima, Shuji; Kohroki, Junya; Masuho, Yasuhiko

2014-09-01

Antibody-dependent cellular cytotoxicity (ADCC) mediated by natural killer (NK) cells is a major mechanism of tumor therapy with antibodies. NK cells not only manifest cytotoxicity but also secrete a variety of cytokines/chemokines that regulate immune responses. Using a retroviral vector, in this study we established a KHYG-1 cell line that stably expresses FcγRIIIA (CD16A). The KHYG-1/FcγRIIIA cells exerted potent antibody concentration-dependent ADCC, whereas parental KHYG-1 cells did not. In contrast, without antibody, the natural killer activity of KHYG-1/FcγRIIIA cells was less potent than that of parental KHYG-1 cells. During the course of ADCC, KHYG-1/FcγRIIIA cells secreted IFN-γ and MIP-1α dependent upon antibody concentration, but parental KHYG-1 cells did not. These results suggest that KHYG-1/FcγRIIIA cells would be useful in studies to elucidate the function of NK cells and the mechanism of ADCC. Copyright © 2014 Elsevier B.V. All rights reserved.

The Worldwide Oil Spill Model (WOSM)

International Nuclear Information System (INIS)

Anderson, E.L.; Howlett, E.; Jayko, K.; Reed, M.; Spaulding, M.; Kolluru, V.

1993-01-01

The Worldwide Oil Spill Model (WOSM) is a standalone microcomputer-based state-of-the-art oil spill model system for use in oil spill response decision support, planning, research, training, and contingency planning. WOSM was developed under support provided by a consortium of oil companies and government agencies. WOSM represents the next generation of oil spill model beyond the OILMAP modelling system (Spaulding et al, 1992). WOSM is designed in a shell architecture in which the only parameters that change are those that describe the area in which the spill model is to be applied. A limited function geographic information system (GIS) is integrated within the model system, and the spill modelling shell has been extended to include interfaces to other GIS systems and digital data. WOSM contains all the databases, data manipulation and graphical display tools, and models to simulate any type of oil spill. The user has control over which weathering processes are to be modelled, and WOSM data input tools enable continual refinement of model predictions as more refined data is imported. Use of WOSM is described and illustrated, showing sample screens and applications. WOSM algorithms and file structure are also outlined. An example test case of a spill in the Juan de Fuca strait is included. 29 refs., 7 figs., 1 tab

Oil sands tailings management project

Energy Technology Data Exchange (ETDEWEB)

Godwalt, C. [Alberta WaterSMART, Calgary, AB (Canada); Kotecha, P. [Suncor Energy Inc, Calgary, AB (Canada); Aumann, C. [Alberta Innovates - Technology Futures, Alberta Governement, AB (Canada)

2010-11-15

The Oil sands leadership initiative (OSLI) works with the Government of Alberta on the development of the oil sands industry, considering environmental, economical and social aspects. Water management was identified as one of most important areas to focus on. Alberta WaterSMART was requested to support the development and the management of projects resulting from the work done or underway in this field. The development of a regional water management solution stood out as the most interesting solution to obtain significant results. In the Athabasca Region, oil sands producers work independently on their water sourcing and disposal with particular attention to fresh water conservation and economics. The Athabasca River represents a source for mines and distant saline aquifers are the target of steam assisted gravity drainage (SAGD) operators. As part of a four-phase project aiming to study the environmental and economic footprint (EEF) benefit of alternatives for Athabasca oil sands production water supply and disposal, the purpose of the tailings water management project was to identify tailings treatment technologies that are ready to be implemented, and to design and evaluate solutions in order to improve regional oil sands production water sourcing and disposal. Alternatives were evaluated based on their total EEF, applying a lifecycle assessment methodology with a particular attention on the quantification of important performance indicators. 25 refs., 8 tabs., 40 figs.

Oil sands tailings management project

International Nuclear Information System (INIS)

Godwalt, C.; Kotecha, P.; Aumann, C.

2010-11-01

The Oil sands leadership initiative (OSLI) works with the Government of Alberta on the development of the oil sands industry, considering environmental, economical and social aspects. Water management was identified as one of most important areas to focus on. Alberta WaterSMART was requested to support the development and the management of projects resulting from the work done or underway in this field. The development of a regional water management solution stood out as the most interesting solution to obtain significant results. In the Athabasca Region, oil sands producers work independently on their water sourcing and disposal with particular attention to fresh water conservation and economics. The Athabasca River represents a source for mines and distant saline aquifers are the target of steam assisted gravity drainage (SAGD) operators. As part of a four-phase project aiming to study the environmental and economic footprint (EEF) benefit of alternatives for Athabasca oil sands production water supply and disposal, the purpose of the tailings water management project was to identify tailings treatment technologies that are ready to be implemented, and to design and evaluate solutions in order to improve regional oil sands production water sourcing and disposal. Alternatives were evaluated based on their total EEF, applying a lifecycle assessment methodology with a particular attention on the quantification of important performance indicators. 25 refs., 8 tabs., 40 figs.

Production of free fatty acids from waste oil by application of ultrasound

Energy Technology Data Exchange (ETDEWEB)

Lima, Larissa P.; Santos, Francisco F.P.; Costa, Enio; Fernandes, Fabiano A.N. [Universidade Federal do Ceara, Departamento de Engenharia Quimica, Fortaleza, CE (Brazil)

2012-12-15

This paper evaluates the production of free fatty acids (FFAs) from waste oil by means of low-frequency high-intensity ultrasound application under atmospheric pressure. To evaluate the potential of this technology, the reaction between waste palm oil and ethanol was carried out. Response surface methodology (RSM) was used to evaluate the influence of alcohol-to-oil weight ratio, potassium hydroxide-to-oil weight ratio, and temperature on the yield of waste oil into FFA. Analysis of the operating conditions by RSM showed that the most important operating conditions affecting the reaction were ethanol-to-oil weight ratio and potassium hydroxide-to-oil weight ratio. The highest yield observed was of 97.3 % after 45 min of reaction. The best operating condition was obtained by applying an ethanol-to-oil weight ratio of 2.4, a potassium hydroxide-to-oil weight ratio of 0.3, and temperature of 60 C. (orig.)

One input-class and two input-class classifications for differentiating olive oil from other edible vegetable oils by use of the normal-phase liquid chromatography fingerprint of the methyl-transesterified fraction.

Science.gov (United States)

Jiménez-Carvelo, Ana M; Pérez-Castaño, Estefanía; González-Casado, Antonio; Cuadros-Rodríguez, Luis

2017-04-15

A new method for differentiation of olive oil (independently of the quality category) from other vegetable oils (canola, safflower, corn, peanut, seeds, grapeseed, palm, linseed, sesame and soybean) has been developed. The analytical procedure for chromatographic fingerprinting of the methyl-transesterified fraction of each vegetable oil, using normal-phase liquid chromatography, is described and the chemometric strategies applied and discussed. Some chemometric methods, such as k-nearest neighbours (kNN), partial least squared-discriminant analysis (PLS-DA), support vector machine classification analysis (SVM-C), and soft independent modelling of class analogies (SIMCA), were applied to build classification models. Performance of the classification was evaluated and ranked using several classification quality metrics. The discriminant analysis, based on the use of one input-class, (plus a dummy class) was applied for the first time in this study. Copyright © 2016 Elsevier Ltd. All rights reserved.

In Vitro antifungal activity of essential oils against Colletotrichum gloeosporioides

Science.gov (United States)

Yusoff, Nor Hanis Aifaa; Abdullah, Siti Aisyah; Othman, Zaulia; Zainal, Zamri

2018-04-01

The efficacy of Citrus hystrix, Azadirachta indica and Cymbopogon citratus essential oils were evaluated for controlling the growth of mycelia and spore germination of Colletotrichum gloeosporioides. In order to determine the best essential oil (EO) and suitable concentration of essential oil, in vitro experiment was conducted by preparing a pure culture of antrachnose on Potato Dextrose Agar containing EOs of C. hystrix, A. indica and C. citratus with different concentrations (0.2%, 0.6%, 1% and 1.4% (v/v)). The result shows that C. hystrix essential oil at a concentration of 1.4% (v/v) reduced of mycelia growth of C. gloeosporioides by 29.49%. A second experiment was conducted, but at higher concentration of each essential oils (1.8%, 2.2%, 2.6% and 2.8% (v/v)). Significant difference (p ≤ 0.05) inhibition of mycelia growth was obtained in all treatments except the control. The antifungal index values of essential oils were proportionally increased with concentration of essential oil applied in each treatment. It is concluded that essential oil from C. hystrix are efficient in inhibiting C. gloeosporioides.

The relationship between SARA fractions and crude oil stability

Directory of Open Access Journals (Sweden)

Siavash Ashoori

2017-03-01

Full Text Available Asphaltene precipitation and deposition are drastic issues in the petroleum industry. Monitoring the asphaltene stability in crude oil is still a serious problem and has been subject of many studies. To investigate crude oil stability by saturate, aromatic, resin and asphaltene (SARA analysis seven types of crudes with different components were used. The applied methods for SARA quantification are IP-143 and ASTM D893-69 and the colloidal instability index (CII is computed from the SARA values as well. In comparison between CII results, the values of oil compositions demonstrated that the stability of asphaltenes in crude oils is a phenomenon that is related to all these components and it cannot be associated only with one of them, individually.

Applying CFD in the analysis of heavy oil - water two-phase flow in joints by using core annular flow technique

Directory of Open Access Journals (Sweden)

T Andrade

2016-09-01

Full Text Available In the oil industry the multiphase flow occur throughout the production chain, from reservoir rock until separation units through the production column, risers and pipelines. During the whole process the fluid flows through the horizontal pipes, curves, connections and T joints. Today, technological and economic challenges facing the oil industry is related to heavy oil transportation due to its unfavourable characteristics such as high viscosity and high density that provokes high pressure drop along the flow. The coreflow technique consists in the injection of small amounts of water into the pipe to form a ring of water between the oil and the wall of the pipe which provides the reduction of friction pressure drop along the flow. This paper aim to model and simulate the transient two-phase flow (water-heavy oil in a horizontal pipe and T joint by numerical simulation using the software ANSYS CFX® Release 12.0. Results of pressure and volumetric fraction distribution inside the horizontal pipe and T joint are presented and analysed.

Geochemical characteristics of crude oil from a tight oil reservoir in the Lucaogou Formation, Jimusar Sag, Junggar Basin

Science.gov (United States)

Cao, Z.

2015-12-01

Jimusar Sag, which lies in the Junggar Basin,is one of the most typical tight oil study areas in China. However, the properties and origin of the crude oil and the geochemical characteristics of the tight oil from the Lucaogou Formation have not yet been studied. In the present study, 23 crude oilsfrom the Lucaogou Formation were collected for analysis, such as physical properties, bulk composition, saturated hydrocarbon gas chromatography-mass spectrometry (GC-MS), and the calculation of various biomarker parameters. In addition,source rock evaluation and porosity permeability analysis were applied to the mudstones and siltstones. Biomarkers of suitable source rocks (TOC>1, S1+S2>6mg/g, 0.7%oil-source correlation. To analyze the hydrocarbon generation history of the Lucaogou source rock, 1D basin modeling was performed. The oil-filling history was also defined by means of basin modeling and microthermometry. The results indicated the presence of low maturity to mature crude oils originating from the burial of terrigenous organic matter beneath a saline lake in the source rocks of mainly type II1kerogen. In addition, a higher proportion of bacteria and algae was shown to contribute to the formation of crude oil in the lower section when compared with the upper section of the Lucaogou Formation. Oil-source correlations demonstrated that not all mudstones within the Lucaogou Formation contributed to oil accumulation.Crude oil from the upper and lower sections originated from thin-bedded mudstones interbedded within sweet spot sand bodies. A good coincidence of filling history and hydrocarbon generation history indicated that the Lucaogou reservoir is a typical in situ reservoir. The mudstones over or beneath the sweet spot bodies consisted of natural caprocks and prevented the vertical movement of oil by capillary forces. Despite being thicker, the thick-bedded mudstone between the upper and lower sweet spots had no obvious contribution to

Waste oil management at the Oak Ridge National Laboratory

International Nuclear Information System (INIS)

Oakes, T.W.; Bird, J.C.; Shank, K.E.; Kelley, B.A.; Harrison, L.L.; Clark, B.R.; Rogers, W.F.

1980-01-01

It is the policy of the Oak Ridge National Laboratory (ORNL) to require that oily substances be handled and disposed of in a manner that protects the environment and personnel from harm. Federal regulations prohibit the discharge of oil into navigable waters, with stiff penalties possible to violators. A strict waste oil management program has been developed and implemented because of the potential for oil problems resulting from the large and varied uses of oil at the Laboratory. Also, past records of improper discharges of oil have mandated immediate corrective actions. In order to resolve the problems of waste oil at the Laboratory, the ORNL Waste Oil Investigation Committee was formed on March 14, 1979. The work of the committee included a survey of every building and area of the Laboratory to locate the presence of oil and the pathways of oil discharges to the environment. The committee also provided a basis for the development of oil spill procedures and waste oil disposal. The Department of Environmental Management (DEM) of the Industrial Safety and Applied Health Physics Division at ORNL has the responsibility of developing environmental protection procedures for the handling and disposal of oil. It approves storage and collection facilities, disposal methods, and disposal sites for oil-containing wastes. The DEM has developed and implemented an ORNL Environmental Protection Procedure for oils and an oil spill prevention and countermeasure plan. In order to familiarize ORNL personnel with the problems and procedures of waste oil, the DEM has held seminars on the subject. This report reviews the findings of the Waste Oil Investigation Committee and the actions of the laboratory management and the DEM in dealing with the waste oil problem at ORNL

REVIEW OF PVT CORRELATIONS FOR CRUDE OILS

African Journals Online (AJOL)

win

approaches that of the fluids used. During the last 50 years, ... applied to crude oils from other regions (Sutton and Farshad,. 1990). ... S. S. Ikiensikimama, Department of Chemistry Engineering, University of Lagos, Lagos, Nigeria. O. Ogboja ...

In situ viscosity of oil sands using low field NMR

International Nuclear Information System (INIS)

Bryan, J.; Moon, D.; Kantzas, A.

2005-01-01

In heavy oil and bitumen reservoirs, oil viscosity is a vital piece of information that will have great bearing on the chosen EOR scheme and the recovery expected. Prediction of in situ viscosity with a logging tool would he very beneficial in reservoir characterization and exploitation design. Low field NMR is a technology that has shown great potential as a tool for characterizing hydrocarbon properties in heavy oil and bitumen reservoirs. An oil viscosity correlation has previously been developed that is capable of providing order of magnitude viscosity estimates for a wide range of oils taken from various fields in Alberta. This paper presents tuning procedures to improve the NMR predictions for different viscosity ranges, and extends the NMR viscosity model to in situ heavy oil in unconsolidated sands. The results of this work show that the NMR oil peak can be de-convoluted from the in situ signals of the oil and water, and the bulk viscosity correlation that was developed for bulk oils can he applied to predict the in situ oil viscosity. These results can be translated to an NMR logging tool algorithm, allowing for in situ measurements of oil viscosity at the proper reservoir conditions. (author)

New technologies of enhanced oil recovery

Directory of Open Access Journals (Sweden)

Paweł Wojnarowski

2006-10-01

Full Text Available It is known from the literature that up to 27 % of oil in oilfields can be produced using primary and hydration methods. The efficiency of production can be increased by employing more advanced methods, i.e. EOR. The Polish Oil and Gas Company iwork with Polish oilfields, where currently primary methods are applied, but the Polish experiences with EOR date back to the years 1932-1987. In view of high oil prices, reconsidering EOR as a production method is economically justifiable. Therefore, it is purposeful to implement new pilot technologies, aimed at implementing new technologies, understanding accompanying phenomena, and calibrating of simulation models, including economical models for an optimal control of the oilfield exploitation. World’s new exploitation methods worked out in the last few years and suggestions for their implementation in Polish conditions are presented in the paper

The Wear Characteristics of Heat Treated Manganese Phosphate Coating Applied to AlSi D2 Steel with Oil Lubricant

Directory of Open Access Journals (Sweden)

Venkatesan Alankaram

2012-12-01

Full Text Available Today, in the area of material design conversion coatings play an important role in the applications where temperature, corrosion, oxidation and wear come in to play. Wear of metals occurs when relative motion between counter-surfaces takes place, leading to physical or chemical destruction of the original top layers. In this study, the tribological behaviour of heat treated Manganese phosphate coatings on AISI D2 steel with oil lubricant was investigated. The Surface morphology of manganese phosphate coatings was examined by Scanning Electron Microscope (SEM and Energy Dispersive X-ray Spectroscopy (EDX .The wear tests were performed in a pin on disk apparatus as per ASTM G-99 Standard. The wear resistance of the coated steel was evaluated through pin on disc test using a sliding velocity of 3.0m/s under Constant loads of 40 N and 100 N with in controlled condition of temperature and humidity. The Coefficient of friction and wear rate were evaluated. Wear pattern of Manganese phosphate coated pins with oil lubricant, Heat treated Manganese phosphate coated pins with oil lubricant were captured using Scanning Electron Microscope (SEM. The results of the wear test established that the heat treated manganese phosphate coating with oil lubricant exhibited the lowest average coefficient of friction and the lowest wear loss up to 6583 m sliding distance under 40 N load and 3000 m sliding distance even under 100 N load respectively. The Wear volume and temperature rise in heat treated Manganese Phosphate coated pins with oil lubricant is lesser than the Manganese Phosphate coated pins with oil lubricant

Vegetable oil spills : oil properties and behaviour

International Nuclear Information System (INIS)

Fingas, M.; Fieldhouse, B.; Jokuty, P.

2001-01-01

In 1997, the United States Environmental Protection Agency conducted a thorough review of the issue regarding vegetable oil spills. Recent attention has refocused on this issue as a result of an incident where 20 tons of canola oil was spilled in the Vancouver Harbour in 2000. In the past, vegetable oils were suggested to be a useful test material because they were thought to be innocuous. It was even suggested they be used to remove petroleum oil residues from beaches. However, recent studies have shown that spills of vegetable oils can have major environmental consequences, equivalent to those of petroleum oil spills. The spills have devastating effects on birds and intertidal organisms. This paper presented a summary of historical vegetable spills from around the world. In this study, specific behaviour tests were examined for several oils including canola, soy bean, olive, castor and corn oils. Evaporation, water-in-oil emulsification and chemical dispersion were measured and were found to be nearly zero, suggesting that vegetable oil spills are not very soluble in water. The aquatic toxicity of vegetable oil is low, but their fate is quite different from petroleum. Vegetable oils do not evaporate to a significant degree, they do not form water-in-oil emulsions, nor do they disperse in water. The physical properties of vegetable oils were also measured, including density and viscosity. This paper presented the aquatic toxicity of several vegetable oils along with other environmental data including the degradation rates noted in the literature. Most environmental damage reported in the literature is by contact with birds feathers resulting in hypothermia and secondly by smothering of intertidal organisms. The effect of vegetable oil on fish has not been well studied, but it is expected that there will be little destructive effect except where smothering can occur. 35 refs., 3 tabs

Vegetable oil spills : oil properties and behaviour

Energy Technology Data Exchange (ETDEWEB)

Fingas, M.; Fieldhouse, B.; Jokuty, P. [Environment Canada, Ottawa, ON (Canada). Emergencies Science Div

2001-07-01

In 1997, the United States Environmental Protection Agency conducted a thorough review of the issue regarding vegetable oil spills. Recent attention has refocused on this issue as a result of an incident where 20 tons of canola oil was spilled in the Vancouver Harbour in 2000. In the past, vegetable oils were suggested to be a useful test material because they were thought to be innocuous. It was even suggested they be used to remove petroleum oil residues from beaches. However, recent studies have shown that spills of vegetable oils can have major environmental consequences, equivalent to those of petroleum oil spills. The spills have devastating effects on birds and intertidal organisms. This paper presented a summary of historical vegetable spills from around the world. In this study, specific behaviour tests were examined for several oils including canola, soy bean, olive, castor and corn oils. Evaporation, water-in-oil emulsification and chemical dispersion were measured and were found to be nearly zero, suggesting that vegetable oil spills are not very soluble in water. The aquatic toxicity of vegetable oil is low, but their fate is quite different from petroleum. Vegetable oils do not evaporate to a significant degree, they do not form water-in-oil emulsions, nor do they disperse in water. The physical properties of vegetable oils were also measured, including density and viscosity. This paper presented the aquatic toxicity of several vegetable oils along with other environmental data including the degradation rates noted in the literature. Most environmental damage reported in the literature is by contact with birds feathers resulting in hypothermia and secondly by smothering of intertidal organisms. The effect of vegetable oil on fish has not been well studied, but it is expected that there will be little destructive effect except where smothering can occur. 35 refs., 3 tabs.

Converting heavy oils into light oils, etc

Energy Technology Data Exchange (ETDEWEB)

Mony, H

1915-12-22

A process is described for transforming heavy oils obtained by the carbonization of lignites, peats, coals, shales into light oils, and also the heavy oils of mineral and vegetable origin, consisting of heating the heavy oils or tars in the presence of one or more solid substances or liquids suitably chosen to cause the distillation of the oils under atmospheric pressure at an appropriate temperature; solid and liquid substances which favor the production of light products under the influence of heat being added preferably to the oil to be treated before putting it in the retort and before heating, so that light oils are obtained by treatment of the heavy oils in a single operation.

DEAD-box helicase DDX27 regulates 3′ end formation of ribosomal 47S RNA and stably associates with the PeBoW-complex

Energy Technology Data Exchange (ETDEWEB)

Kellner, Markus; Rohrmoser, Michaela [Department of Molecular Epigenetics, Helmholtz Center Munich, Center for Integrated Protein Science Munich (CIPSM), Marchioninistr. 25, Munich 81377 (Germany); Forné, Ignasi [Adolf Butenandt Institute, Ludwig Maximilians University of Munich, Center for Integrated Protein Science Munich (CIPSM), Schillerstr. 44, Munich 80336 (Germany); Voss, Kirsten; Burger, Kaspar; Mühl, Bastian; Gruber-Eber, Anita [Department of Molecular Epigenetics, Helmholtz Center Munich, Center for Integrated Protein Science Munich (CIPSM), Marchioninistr. 25, Munich 81377 (Germany); Kremmer, Elisabeth [Institute of Molecular Immunology, Helmholtz Center Munich, Marchioninistr. 25, Munich 81377 (Germany); Imhof, Axel [Adolf Butenandt Institute, Ludwig Maximilians University of Munich, Center for Integrated Protein Science Munich (CIPSM), Schillerstr. 44, Munich 80336 (Germany); Eick, Dirk, E-mail: eick@helmholtz-muenchen.de [Department of Molecular Epigenetics, Helmholtz Center Munich, Center for Integrated Protein Science Munich (CIPSM), Marchioninistr. 25, Munich 81377 (Germany)

2015-05-15

PeBoW, a trimeric complex consisting of pescadillo (Pes1), block of proliferation (Bop1), and the WD repeat protein 12 (WDR12), is essential for processing and maturation of mammalian 5.8S and 28S ribosomal RNAs. Applying a mass spectrometric analysis, we identified the DEAD-box helicase DDX27 as stably associated factor of the PeBoW-complex. DDX27 interacts with the PeBoW-complex via an evolutionary conserved F×F motif in the N-terminal domain and is recruited to the nucleolus via its basic C-terminal domain. This recruitment is RNA-dependent and occurs independently of the PeBoW-complex. Interestingly, knockdown of DDX27, but not of Pes1, induces the accumulation of an extended form of the primary 47S rRNA. We conclude that DDX27 can interact specifically with the Pes1 and Bop1 but fulfils critical function(s) for proper 3′ end formation of 47S rRNA independently of the PeBoW-complex. - Highlights: • DEAD-box helicase DDX27 is a new constituent of the PeBoW-complex. • The N-terminal F×F motif of DDX27 interacts with the PeBoW components Pes1 and Bop1. • Nucleolar anchoring of DDX27 via its basic C-terminal domain is RNA dependent. • Knockdown of DDX27 induces a specific defect in 3′ end formation of 47S rRNA.

Conductometric Sensors for Monitoring Degradation of Automotive Engine Oil

Directory of Open Access Journals (Sweden)

Franz L. Dickert

2011-09-01

Full Text Available Conductometric sensors have been fabricated by applying imprinted polymers as receptors for monitoring engine oil quality. Titania and silica layers are synthesized via the sol-gel technique and used as recognition materials for acidic components present in used lubricating oil. Thin-film gold electrodes forming an interdigitated structure are used as transducers to measure the conductance of polymer coatings. Optimization of layer composition is carried out by varying the precursors, e.g., dimethylaminopropyltrimethoxysilane (DMAPTMS, and aminopropyl-triethoxysilane (APTES. Characterization of these sensitive materials is performed by testing against oil oxidation products, e.g., carbonic acids. The results depict that imprinted aminopropyltriethoxysilane (APTES polymer is a promising candidate for detecting the age of used lubricating oil. In the next strategy, polyurethane-nanotubes composite as sensitive material is synthesized, producing appreciable differentiation pattern between fresh and used oils at elevated temperature with enhanced sensitivity.

Impact of oil price shocks on selected macroeconomic variables in Nigeria

International Nuclear Information System (INIS)

Iwayemi, Akin; Fowowe, Babajide

2011-01-01

The impact of oil price shocks on the macroeconomy has received a great deal of attention since the 1970 s. Initially, many empirical studies found a significant negative effect between oil price shocks and GDP but more recently, empirical studies have reported an insignificant relationship between oil shocks and the macroeconomy. A key feature of existing research is that it applies predominantly to advanced, oil-importing countries. For oil-exporting countries, different conclusions are expected but this can only be ascertained empirically. This study conducts an empirical analysis of the effects of oil price shocks on a developing country oil-exporter - Nigeria. Our findings showed that oil price shocks do not have a major impact on most macroeconomic variables in Nigeria. The results of the Granger-causality tests, impulse response functions, and variance decomposition analysis all showed that different measures of linear and positive oil shocks have not caused output, government expenditure, inflation, and the real exchange rate. The tests support the existence of asymmetric effects of oil price shocks because we find that negative oil shocks significantly cause output and the real exchange rate. (author)

Reduction of light oil usage as power fluid for jet pumping in deep heavy oil reservoirs

Energy Technology Data Exchange (ETDEWEB)

Chen, S.; Li, H.; Yang, D. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Regina Univ., SK (Canada); Zhang, Q. [China Univ. of Petroleum, Dongying, Shandong (China); He, J. [China National Petroleum Corp., Haidan District, Beijing (China). PetroChina Tarim Oilfield Co.

2008-10-15

In deep heavy oil reservoirs, reservoir fluid can flow more easily in the formation as well as around the bottomhole. However, during its path along the production string, viscosity of the reservoir fluid increases dramatically due to heat loss and release of the dissolved gas, resulting in significant pressure drop along the wellbore. Artificial lifting methods need to be adopted to pump the reservoir fluids to the surface. This paper discussed the development of a new technique for reducing the amount of light oil used for jet pumping in deep heavy oil wells. Two approaches were discussed. Approach A uses the light oil as a power fluid first to obtain produced fluid with lower viscosity, and then the produced fluid is reinjected into the well as a power fluid. The process continues until the viscosity of the produced fluid is too high to be utilized. Approach B combines a portion of the produced fluid with the light oil at a reasonable ratio and then the produced fluid-light oil mixture is used as the power fluid for deep heavy oil well production. The viscosity of the blended power fluid continue to increase and eventually reach equilibrium. The paper presented the detailed processes of both approaches in order to indicate how to apply them in field applications. Theoretic models were also developed and presented to determine the key parameters in the field operations. A field case was also presented and a comparison and analysis between the two approaches were discussed. It was concluded from the field applications that, with a certain amount of light oil, the amount of reservoir fluid produced by using the new technique could be 3 times higher than that of the conventional jet pumping method. 17 refs., 3 tabs., 6 figs.

Bio-Detergent oil derivative used frying

Directory of Open Access Journals (Sweden)

Alfonso Jesús Torres Ortega

2011-04-01

Full Text Available Currently, the global trend towards sustainable development for environmental friendly products such as biosurfactants shows an excellent performance. Anionic surface active agents can be produced from renewable natural raw materials such as vegetable oils mainly derived from palm oil. Methyl ester sulfonate is an active component of highly biodegradable detergents, one advantage compared with detergents derived from petrochemicals which generate a high pollutant load. This paper proposes the study of sulfonation with sulfur trioxide of esters derived from waste cooking oil which main component is palm oil. The falling film reactor allows determining the conditions of the process at pilot scale. The experimentation allowed an enhancement of empirical equations in the equipment implemented for this purpose and to determine some physicochemical properties. The comparison obtained for this same process with petrochemicals compounds indicates that the model could be applied to any film sulfonation but adjusting the parameters and specific conditions, such as the physicochemical properties of the compounds used, since the sulfonation process described in this work is one of the more complicated cases. The technological development presented here seeks to contribute with the industrial needs to promote green chemical industry for the production of biosurfactant from waste frying oil.

Energetic Efficiency of red palm oil

Directory of Open Access Journals (Sweden)

Byron Jiménez

2013-11-01

Full Text Available The main goal of this paper is to determine the energy efficiency in the production of red palm oil (Elaeis guineensis by using the biophysical indicator EROI, postulated by the Ecological Economics. This indicator is applied to compare the energy used in the preparation of synthetic fertilizers (to fill its nutritional demands versus the energy contained in the oil. In 2009, there were 195.550 hectares of land planted with African palm in Ecuador (INEC, 2011. In addition, between 2002 and 2009, there were 2,7 million tons of red oil (FEDEPAL, 2010. It is determined that for each unit of energy consumed, 4.82 units of energy are contained in the red oil. The energy used in making pesticides for cultivation, consumed in transportation, refining, and post harvest is excluded because this other energy would drastically reduce the absolute data of the indicator, which is already inefficient for the high energy consumption it requires to generate the energy contained in the oil. On the other hand, agroecology has proven to be more efficient in the generation of energy per unit of invested energy (Altieri et. al., 2010; Moore, 2004.

Repellent activity of herbal essential oils against Aedes aegypti (Linn. and Culex quinquefasciatus (Say.

Directory of Open Access Journals (Sweden)

Duangkamon Sritabutra

2013-08-01

Full Text Available Objective: To determine the mosquito repellent activity of herbal essential oils against female Aedes aegypti and Culex quinquefasciatus. Methods: On a volunteer’s forearm, 0.1 mL of each essential oil was applied to 3 cm伊10 cm of exposed skin. The protection time was recorded for 3 min after every 30 min. Results: Essential oil from clove oil in olive oil and in coconut oil gave the longest lasting period of 76.50 min and 96.00 min respectively against Aedes aegypti. The citronella grass oil in olive oil, citronella grass oil in coconut oil and lemongrass oil in coconut oil exhibited protection against Culex quinquefasciatus at 165.00, 105.00, and 112.50 min respectively. Conclusions: The results clearly indicated that clove, citronella and lemongrass oil were the most promising for repellency against mosquito species. These oils could be used to develop a new formulation to control mosquitoes.

Oil migration through unsaturated soils and its effect on the Vadose Zone Interactive Processes (VIP) model output

International Nuclear Information System (INIS)

Joseph, A.T.; Grenney, W.J.; Stevens, D.K.

1994-01-01

The VIP model, which simulates the concentration profiles of the hazardous compounds in the soil, water, and the air phases, assumes a fixed oily phase. The purpose of this study was to measure oil migration in soil systems and to determine its effect on the VIP model output. Experiments were conducted to demonstrate the mobility of an oil through the unsaturated zone of the soil. The studies were conducted in laboratory scale glass columns. A light petroleum oil and two types of soil were used. The experiments demonstrated that oil migrates down significantly through the soil columns. The extent of migration depended on the volume of oil applied and the type of soil. However, the applied oil was completely immobilized in the columns. The model was modified to incorporate oil migration. The modified model can be expected to produce more realistic contaminant concentration profiles during land treatment of oily wastes when compared to that produced by the present version of the VIP model. (Author)

European oil product supply modelling

International Nuclear Information System (INIS)

Saint-Antonin, V.

1998-01-01

Over the last few years, trends in European oil product consumption (in terms of level as structure and quality) has important implications of the refining industry. In this context, the purpose of this thesis consists in building a mathematical programming model applied to the European refineries in order to determine oil product supply prices, European refining industry investments and oil product exchanges of the European Union. The first part presents the reason for our choice for a long-term aggregate multi-refineries linear programming model, based on European refineries characteristics and the objectives of our model. Its dual properties are studied in detail and we focus particularly on the European exchange modelling. In the second part, an analysis of the European refining trends leads us to identify parameters and variables of the model that are essential to the aggregate representation of the European oil product supply. The third part is devoted to the use of this model, regarding two scenarios of increasingly stringent specifications for gasoline and diesel oil. Our interest for these products is due to their important share of the European oil product consumption and the not insignificant responsibility of the transport sector for atmospheric pollution. Finally, in order to have the use of an overall picture of the European refining industry, we build a regression model summarizing, though a few equations, the main relations between the major endogenous and exogenous variables o the LP model. Based on pseudo-data, this kind of model provides a simple and robust representation of the oil product supply. But a more specialized analysis of the refining industry operations, turning on a technical assessment of processing units, is reliant on the use of an optimization model such as the model we have built. (author)

Prospects for applications of electron beams in processing of gas and oil hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Ponomarev, A. V., E-mail: ponomarev@ipc.rssi.ru [Russian Academy of Sciences, Frumkin Institute of Physical Chemistry and Electrochemistry (Russian Federation); Pershukov, V. A. [ROSATOM National Nuclear Corporation (Russian Federation); Smirnov, V. P. [CJSC “Nauka i Innovatsii” (Russian Federation)

2015-12-15

Waste-free processing of oil and oil gases can be based on electron-beam technologies. Their major advantage is an opportunity of controlled manufacturing of a wide range of products with a higher utility value at moderate temperatures and pressures. The work considers certain key aspects of electron beam technologies applied for the chain cracking of heavy crude oil, for the synthesis of premium gasoline from oil gases, and also for the hydrogenation, alkylation, and isomerization of unsaturated oil products. Electronbeam processing of oil can be embodied via compact mobile modules which are applicable for direct usage at distant oil and gas fields. More cost-effective and reliable electron accelerators should be developed to realize the potential of electron-beam technologies.

Determination of sulfur compounds in hydrotreated transformer base oil by potentiometric titration.

Science.gov (United States)

Chao, Qiu; Sheng, Han; Cheng, Xingguo; Ren, Tianhui

2005-06-01

A method was developed to analyze the distribution of sulfur compounds in model sulfur compounds by potentiometric titration, and applied to analyze hydrotreated transformer base oil. Model thioethers were oxidized to corresponding sulfoxides by tetrabutylammonium periodate and sodium metaperiodate, respectively, and the sulfoxides were titrated by perchloric acid titrant in acetic anhydride. The contents of aliphatic thioethers and total thioethers were then determined from that of sulfoxides in solution. The method was applied to determine the organic sulfur compounds in hydrotreated transformer base oil.

Green bio-oil extraction for oil crops

Science.gov (United States)

Zainab, H.; Nurfatirah, N.; Norfaezah, A.; Othman, H.

2016-06-01

The move towards a green bio-oil extraction technique is highlighted in this paper. The commonly practised organic solvent oil extraction technique could be replaced with a modified microwave extraction. Jatropha seeds (Jatropha curcas) were used to extract bio-oil. Clean samples were heated in an oven at 110 ° C for 24 hours to remove moisture content and ground to obtain particle size smaller than 500μm. Extraction was carried out at different extraction times 15 min, 30 min, 45 min, 60 min and 120 min to determine oil yield. The biooil yield obtained from microwave assisted extraction system at 90 minutes was 36% while that from soxhlet extraction for 6 hours was 42%. Bio-oil extracted using the microwave assisted extraction (MAE) system could enhance yield of bio-oil compared to soxhlet extraction. The MAE extraction system is rapid using only water as solvent which is a nonhazardous, environment-friendly technique compared to soxhlet extraction (SE) method using hexane as solvent. Thus, this is a green technique of bio-oil extraction using only water as extractant. Bio-oil extraction from the pyrolysis of empty fruit bunch (EFB), a biomass waste from oil palm crop, was enhanced using a biocatalyst derived from seashell waste. Oil yield for non-catalytic extraction was 43.8% while addition of seashell based biocatalyst was 44.6%. Oil yield for non-catalytic extraction was 43.8% while with addition of seashell-based biocatalyst was 44.6%. The pH of bio-oil increased from 3.5 to 4.3. The viscosity of bio-oil obtained by catalytic means increased from 20.5 to 37.8 cP. A rapid and environment friendly extraction technique is preferable to enhance bio-oil yield. The microwave assisted approach is a green, rapid and environmental friendly extraction technique for the production of bio-oil bearing crops.

Nuclear energy in the oils sands

International Nuclear Information System (INIS)

Arsenault, J.E.

2014-01-01

The major Canadian oil sands are located in Alberta and Saskatchewan, with most production from the strata along the Athabasca River in Alberta. The economically recoverable oil sands reserves are estimated to be 168 billion barrels which at a current production rate of 1.8 million barrels per day (2012), are projected to last a very long time. Canada has been blessed with vast energy resources which make it potentially energy-independent and able to provide significant exports but there are concerns that their development cannot be managed in a wholly acceptable manner. Comparable concerns have been applied to nuclear energy in the past and in recent times to the oil sands. The technologies associated with these energy sources have always been controversial because they are at the confluence of economics and politics where finding a balance between risk and reward is difficult. So it should be no surprise that when these technologies get linked together in certain proposals their prospect for success is doubly difficult. The possible use of nuclear energy for production of oil from the oil sands dates back to the late 1950s, when an experiment to mine the oil by detonating an underground nuclear device was proposed. It was predicted that the heat and pressure released from such a device would create a large cavern into which oil would flow, and from where it would be pumped to the surface. Almost at the same time, oil sands research using conventional sources of energy had culminated with the development of practical refining processes, essentially those still in use today. These methods require large amounts of heat energy in the form of hot water and steam. In this century nuclear energy was proposed as the source for the heat required by the oil sands production processes. To date neither of these nuclear proposals for oil sands projects have been successful, because the economic and political balance could not be struck. (author)

Nuclear energy in the oils sands

Energy Technology Data Exchange (ETDEWEB)

Arsenault, J.E.

2014-09-15

The major Canadian oil sands are located in Alberta and Saskatchewan, with most production from the strata along the Athabasca River in Alberta. The economically recoverable oil sands reserves are estimated to be 168 billion barrels which at a current production rate of 1.8 million barrels per day (2012), are projected to last a very long time. Canada has been blessed with vast energy resources which make it potentially energy-independent and able to provide significant exports but there are concerns that their development cannot be managed in a wholly acceptable manner. Comparable concerns have been applied to nuclear energy in the past and in recent times to the oil sands. The technologies associated with these energy sources have always been controversial because they are at the confluence of economics and politics where finding a balance between risk and reward is difficult. So it should be no surprise that when these technologies get linked together in certain proposals their prospect for success is doubly difficult. The possible use of nuclear energy for production of oil from the oil sands dates back to the late 1950s, when an experiment to mine the oil by detonating an underground nuclear device was proposed. It was predicted that the heat and pressure released from such a device would create a large cavern into which oil would flow, and from where it would be pumped to the surface. Almost at the same time, oil sands research using conventional sources of energy had culminated with the development of practical refining processes, essentially those still in use today. These methods require large amounts of heat energy in the form of hot water and steam. In this century nuclear energy was proposed as the source for the heat required by the oil sands production processes. To date neither of these nuclear proposals for oil sands projects have been successful, because the economic and political balance could not be struck. (author)

Effect of mineral oil, sunflower oil, and coconut oil on prevention of hair damage.

Science.gov (United States)

Rele, Aarti S; Mohile, R B

2003-01-01

Previously published results showed that both in vitro and in vivo coconut oil (CNO) treatments prevented combing damage of various hair types. Using the same methodology, an attempt was made to study the properties of mineral oil and sunflower oil on hair. Mineral oil (MO) was selected because it is extensively used in hair oil formulations in India, because it is non-greasy in nature, and because it is cheaper than vegetable oils like coconut and sunflower oils. The study was extended to sunflower oil (SFO) because it is the second most utilized base oil in the hair oil industry on account of its non-freezing property and its odorlessness at ambient temperature. As the aim was to cover different treatments, and the effect of these treatments on various hair types using the above oils, the number of experiments to be conducted was a very high number and a technique termed as the Taguchi Design of Experimentation was used. The findings clearly indicate the strong impact that coconut oil application has to hair as compared to application of both sunflower and mineral oils. Among three oils, coconut oil was the only oil found to reduce the protein loss remarkably for both undamaged and damaged hair when used as a pre-wash and post-wash grooming product. Both sunflower and mineral oils do not help at all in reducing the protein loss from hair. This difference in results could arise from the composition of each of these oils. Coconut oil, being a triglyceride of lauric acid (principal fatty acid), has a high affinity for hair proteins and, because of its low molecular weight and straight linear chain, is able to penetrate inside the hair shaft. Mineral oil, being a hydrocarbon, has no affinity for proteins and therefore is not able to penetrate and yield better results. In the case of sunflower oil, although it is a triglyceride of linoleic acid, because of its bulky structure due to the presence of double bonds, it does not penetrate the fiber, consequently resulting

Pengaruh Konsentrasi Minyak Kelapa Murni (Virgin Coconut Oil dan Minyak Jarak (Castor Oil terhadap Sifat Fisikokimia dan Organoleptik Sabun Mandi Cair

Directory of Open Access Journals (Sweden)

Asri Widyasanti

2017-04-01

Full Text Available VCO contains of lauric acid that perform to smooth and to moisturize the skin. Castor oil has ricinoleic acid that serves to protect the skin. Therefore, both of the oil are suitable to be the raw material for liquid soap making. This study aimed were to produce a liquid soap, to determine the exact concentration of VCO and castor oil for liquid soap and to find out the effect of VCO and Castor Oil concentrations to the characteristics of liquid soap. The method used was laboratory experimental method with descriptive analysis. The treatments in this study were A =concentrations of VCO 100 %, B = concentrations of VCO 80 % and castor oil 20 %, C = concentrations of VCO 50 % and castor oil 50 %, D = concentrations of VCO 20 % and castor oil 80 %, and E = concentrations of castor oil 100 %,  from 200 gram soap base. The parameter observed for liquid soap included chemical properties, physical properties of soap, and organoleptic test. The result shows that all treatments complies the requirement SNI 06-4085-1996. The formula of liquid soap with treatment B was revealed as the best product with 0.01 % of total alkali content, pH value of 9.16 , specific gravity 1.06, and total plate count 5colonies/g. This technology process of natural liquid soap production with the VCO and castor oil could be develop and apply in industrial scale.

Soap-scented oil skin patch in the treatment of fibromyalgia: A case series

Directory of Open Access Journals (Sweden)

Yon Doo Ough

2008-09-01

Full Text Available Yon Doo OughDepartment of Anesthesiology, Beloit Memorial Hospital, Beloit, WI, USAAbstract: Treatment for fibromyalgia is largely empiric and supportive, and favors a multidisciplinary approach. Despite treatment, symptomatic relief is often inadequate and temporary. Over 90% of fibromyalgia patients seek alternative medical care. There is much anecdotal evidence that applying a bar of soap to the skin can relieve leg cramps. Expanding on this idea, I created a skin patch from soap-scented oil, which was used to treat muscular pain and spasms. After receiving positive feedback from several patients, I hypothesized that the scent of the oil itself, applied directly to the skin, is responsible for the pain-relieving and muscle-relaxant properties of the skin patch. Furthermore, I hypothesize that this soap-scented oil skin patch is an effective treatment for the pain associated with fibromyalgia.Keywords: fibromyalgia, headache, soap-scented oil skin patch

INVESTIGATION ON CHEMICAL COMPOSITION, ANTIMICROBIAL, ANTIOXIDANT, AND CYTOTOXIC PROPERTIES OF ESSENTIAL OIL FROM DRACOCEPHALUM KOTSCHYI BOISS.

Science.gov (United States)

Ashrafi, Behnam; Ramak, Parvin; Ezatpour, Behrouz; Talei, Gholam Reza

2017-01-01

Dracocephalum kotschyi Boiss is a herb with wide-spread applications. Lorestan traditional healers have applied it for the treatment of rheumatoid diseases and stomach disorders. Hydrodistillation process was used for essential oil extraction, the extracted essential oil was then analyzed through combination of capillary GC-FID, GC-MS and RI. The in vitro antimicrobial, antioxidant and cytotoxic activities of this essential oil were examined. Results indicate that the essential oil has a broad range of anti-microbial activity against all of the tested microorganisms. The 50% of cytotoxic concentrations was 26.4 μg/ml and 4266.7 μg/ml for Hela cells and human lymphocytes, respectively. The oil cytotoxicity against the human tumor cell line was far higher than the amount required for human healthy cells. Conversely, the essential oil's IC 50 value of 49.2 μg/ml in the DPPH assay, could be regarded as its strong antioxidant potential. According to the data obtained, it can be concluded that D. kotschyi essential oil could be applied as a safe antibacterial and antioxidant agent for food and pharmaceutical purposes.

Superoleophillic electrospun polystrene/exofoliated graphite fibre for selective removal of crude oil from water

Science.gov (United States)

Alayande, S. Oluwagbemiga; Dare, Enock O.; Olorundare, F. O. Grace; Nkosi, D.; Msagati, Titus A. M.; Mamba, B. B.

2016-04-01

During oil spills, the aquatic environment is greatly endangered because oil floats on water making the penetration of sunlight difficult therefore primary productivity is compromised, birds and aquatic organisms are totally eliminated within a short period. It is therefore essential to remove the oil from the water bodies after the spillage. This work reports on the fabrication of oil loving electrospun polystyrene-exofoliated graphite fibre with hydrophobic and oleophillic surface properties. The fibre was applied for the selective adsorption of crude oil from simulated crude oil spillage on water. The maximum oil adsorption capacity of the EPS/EG was 1.15 kg/g in 20 min while the lowest oil adsorption capacity was 0.81 kg/g in 10 min. Cheap oil adsorbent was developed with superoleophillic and superhydrophobic properties.

Horizontal oil well applications and oil recovery assessment. Volume 2: Applications overview, Final report

Energy Technology Data Exchange (ETDEWEB)

Deskins, W.G.; McDonald, W.J.; Knoll, R.G.; Springer, S.J.

1995-03-01

Horizontal technology has been applied in over 110 formations in the USA. Volume 1 of this study addresses the overall success of horizontal technology, especially in less-publicized formations, i.e., other than the Austin Chalk, Bakken, and Niobrara. Operators in the USA and Canada were surveyed on a formation-by-formation basis by means of a questionnaire. Response data were received describing horizontal well projects in 58 formations in the USA and 88 in Canada. Operators` responses were analyzed for trends in technical and economic success based on lithology (clastics and carbonates) and resource type (light oil, heavy oil, and gas). The potential impact of horizontal technology on reserves was also estimated. A forecast of horizontal drilling activity over the next decade was developed.

Characterization of orange oil microcapsules for application in textiles

Science.gov (United States)

Rossi, W.; Bonet-Aracil, M.; Bou-Belda, E.; Gisbert-Payá, J.; Wilson, K.; Roldo, L.

2017-10-01

The use of orange oil presents as an ecological alternative to chemicals, attracting the attention of the scientific community to the development of eco-friendly antimicrobials. The microencapsulation technology has been used for the application of orange oil to textiles, being an economically viable, fast and efficient method by combining core and shell materials, desirable perceptual and functional characteristics, responsible for properties related to the nature of the product and provides that the wall materials release the functional substances in a controlled manner, in addition to effectively protecting and isolating the core material from the external environment to prevent its volatilization and deterioration, increasing the stability of the oil, such as non-toxicity. Thus, to better exploit the properties of the orange essential oil applied to textile products this study presents a characterization of microcapsules of Melamine formaldehyde obtained by the interfacial polymerization method with variations of proportions of orange oil (volatile) with fixed oil Medium-Chain Triglycerides (MCT) (non-volatile) to assist in the stability of the orange essential oil. Scanning electron microscope (SEM) was used as visualizing tool to characterize microparticles and surface morphology and thermal characteristics of microcapsules were premeditated by mean Differential scanning calorimetry (DSC).

Effects of Oil Shocks on the Unemployment: GVAR Approach

Directory of Open Access Journals (Sweden)

Malek KhojastehNeghad

2017-09-01

Full Text Available Oil is not only one of the most significant and useful consumer goods but also is a remarkable material in energy production all around the world which has a lot of price fluctuation. oil shocks consider as a principal factor of many financial crises and have various effects on economy of countries. Hence, the assessment of price fluctuations on macroeconomic variables such as unemployment seems important. This paper survey the oil price inconstancy on unemployment in 31countries during the period from the second quarter of 1985 to the fourth quarter of 2009 through Global Vector Auto-Regression model. Results demonstrate except of the rest of W. Europe, there is a positive relationship between oil prices oscillation and unemployment. It should be noted in many area the feedback along with the lag that depends on the ratio of oil cost in national income, reliance level to imported oil, end-users ability to reduce their usage and substitute other sources, gas consumption quantity in economy, effect of higher prices on other energy sources, monetary policies adopt when face with oil price swaging and capability of goverments to apply the vary policies.

Combination of Analytical and Chemometric Methods as a Useful Tool for the Characterization of Extra Virgin Argan Oil and Other Edible Virgin Oils. Role of Polyphenols and Tocopherols.

Science.gov (United States)

Rueda, Ascensión; Samaniego-Sánchez, Cristina; Olalla, Manuel; Giménez, Rafael; Cabrera-Vique, Carmen; Seiquer, Isabel; Lara, Luis

2016-01-01

Analysis of phenolic profile and tocopherol fractions in conjunction with chemometrics techniques were used for the accurate characterization of extra virgin argan oil and eight other edible vegetable virgin oils (olive, soybean, wheat germ, walnut, almond, sesame, avocado, and linseed) and to establish similarities among them. Phenolic profile and tocopherols were determined by HPLC coupled with diode-array and fluorescence detectors, respectively. Multivariate factor analysis (MFA) and linear correlations were applied. Significant negative correlations were found between tocopherols and some of the polyphenols identified, but more intensely (P tocopherol and oleuropein, pinoresinol, and luteolin. MFA revealed that tocopherols, especially γ-fraction, most strongly influenced the oil characterization. Among the phenolic compounds, syringic acid, dihydroxybenzoic acid, oleuropein, pinoresinol, and luteolin also contributed to the discrimination of the oils. According to the variables analyzed in the present study, argan oil presented the greatest similarity with walnut oil, followed by sesame and linseed oils. Olive, avocado, and almond oils showed close similarities.

The Effects of Crude Oil on Stock Markets with use of Markov Switching Models

OpenAIRE

Wiese, Thor August Mediaas

2016-01-01

In this thesis, a two regime Markov switching (MS) model is implemented to examine the relationship between crude oil, both brent oil and WTI, and stock markets. In particular, the model is applied to stock markets in both oil importing and exporting countries which include Canada, China, Japan, Germany, Netherlands, Norway, the United Kingdom and the United States. This paper first evaluates the significance of oil parameters in the detected regimes, where the two regimes respond to low mean...

Essays on oil and the macroeconomy

Energy Technology Data Exchange (ETDEWEB)

Melolinna, M.

2012-07-01

This dissertation studies the effects of crude oil on the macroeconomy using a vector autoregression (VAR) modelling framework. In particular, the importance of identifying different types of oil shocks is explored for both small and large open economies. A VAR model is also used to study the information content of oil futures contracts. The dissertation consists of three essays. The first essay of the dissertation introduces a methodology for identifying oil supply shocks in a small open economy. Financial market information is used to construct an identification scheme that forces the response to an oil shock of the VAR model to be the same as that implied by futures markets. Due to the identification scheme, the model is only partially identified, and confidence intervals for impulse responses are calculated by using a bootstrapping procedure. The methodology is applied in illustrative examples to two small open economies in a VAR model that includes key domestic and international macroeconomic variables. The results suggest that while oil supply shocks have had an effect on domestic inflation during recent past, the effect on domestic GDP is ambiguous. The second essay of the dissertation studies the existence of risk premiums in crude oil futures prices with simple ordinary least squares regression and Bayesian VAR models. It also studies the importance of three main theoretical risk premium models in explaining and forecasting the risk premiums in practice. Whilst the existence of the premiums and the validity of the models can be established at certain time points, it turns out that the choice of sample period has a considerable effect on the results. Hence, the risk premiums are highly time-varying. The study also establishes a model, based on speculative positions in the futures markets, which has some predictive power for future oil spot prices. The third essay of the dissertation explores oil market and other macroeconomic shocks in a structural VAR

The Environmental Challenges for the Oil Industry

International Nuclear Information System (INIS)

Del Manso, F.

1998-01-01

Oil has been and will continue to be indispensable to assure the growth of the world economy, but it is also responsible to have an impact on the environment. One of the most important challenges for the future, in particular for the oil sector, is to make this growth sustainable for the environment. To do this, refineries must plan a huge amount of investments for the next future to modify substantially their industrial structures to reformulate transportation fuels (diesel and gasoline) to comply the new limits for the emissions generated during the production and distribution of oil products and to apply new safety rules in order to improve the compatibility of the refineries with the territory. To fulfil all this actions the oil sector will have to face very high costs without any certainty of the return of investments, due to the extreme uncertainty to forecast the future oil demand in Italy after the Kyoto Protocol. To be ready within the year 2005, Italian refineries must decide now to invest, but they are not sure to have a market in the future for the products that they are going to produce [it

French civil law aspects of international sales of oil

International Nuclear Information System (INIS)

Moquet, A.

1992-01-01

There is not in France, as in London and New York, and organised trade market for crude oil and oil products. French law does not apply to oil futures negotiated in foreign markets, although solicitation in France for transactions in a foreign market is legal only if that market is approved by the French Minister in charge of Economic Affairs. However, French oil producers do enter into OTC forward and commodity swap agreements. Although most of these agreements are standardised and expressly choose English law and the jurisdiction of the High Court of London for resolution of disputes, fundamental principles of French private international law may impose jurisdiction of a French Commercial Court (in case of bankruptcy of the French party for example) and/or rules of necessary application or public order. (author)

SOLVENT-BASED ENHANCED OIL RECOVERY PROCESSES TO DEVELOP WEST SAK ALASKA NORTH SLOPE HEAVY OIL RESOURCES

Energy Technology Data Exchange (ETDEWEB)

David O. Ogbe; Tao Zhu

2004-01-01

A one-year research program is conducted to evaluate the feasibility of applying solvent-based enhanced oil recovery processes to develop West Sak and Ugnu heavy oil resources found on the Alaska North Slope (ANS). The project objective is to conduct research to develop technology to produce and market the 300-3000 cp oil in the West Sak and Ugnu sands. During the first phase of the research, background information was collected, and experimental and numerical studies of vapor extraction process (VAPEX) in West Sak and Ugnu are conducted. The experimental study is designed to foster understanding of the processes governing vapor chamber formation and growth, and to optimize oil recovery. A specially designed core-holder and a computed tomography (CT) scanner was used to measure the in-situ distribution of phases. Numerical simulation study of VAPEX was initiated during the first year. The numerical work completed during this period includes setting up a numerical model and using the analog data to simulate lab experiments of the VAPEX process. The goal was to understand the mechanisms governing the VAPEX process. Additional work is recommended to expand the VAPEX numerical study using actual field data obtained from Alaska North Slope.

Skin Penetration Enhancement by Natural Oils for Dihydroquercetin Delivery.

Science.gov (United States)

Čižinauskas, Vytis; Elie, Nicolas; Brunelle, Alain; Briedis, Vitalis

2017-09-12

Natural oils are commonly used in topical pharmaceutical formulations as emulsifiers, stabilizers or solubility enhancers. They are presented as safe and inert components, mainly used for formulation purposes. It is confirmed that natural oils can affect the skin penetration of various substances. Fatty acids are mainly responsible for this effect. Current understanding lacks reliable scientific data on penetration of natural oils into the skin and their skin penetration enhancement potential. In the current study, fatty acid content analysis was used to determine the principal fatty acids in soybean, olive, avocado, sea-buckthorn pulp, raspberry seed and coconut oils. Time of flight secondary ion mass spectrometry bioimaging was used to determine the distribution of these fatty acids in human skin ex vivo after application of the oils. Skin penetration enhancement ratios were determined for a perspective antioxidant compound dihydroquercetin. The results demonstrated skin penetration of fatty acids from all oils tested. Only soybean and olive oils significantly increased the skin distribution of dihydroquercetin and can be used as skin penetration enhancers. However, no correlation can be determined between the fatty acids' composition and skin penetration enhancement using currently available methodological approaches. This indicates that potential chemical penetration enhancement should be evaluated during formulation of topically applied products containing natural oils.

Chemometric techniques in oil classification from oil spill fingerprinting.

Science.gov (United States)

Ismail, Azimah; Toriman, Mohd Ekhwan; Juahir, Hafizan; Kassim, Azlina Md; Zain, Sharifuddin Md; Ahmad, Wan Kamaruzaman Wan; Wong, Kok Fah; Retnam, Ananthy; Zali, Munirah Abdul; Mokhtar, Mazlin; Yusri, Mohd Ayub

2016-10-15

Extended use of GC-FID and GC-MS in oil spill fingerprinting and matching is significantly important for oil classification from the oil spill sources collected from various areas of Peninsular Malaysia and Sabah (East Malaysia). Oil spill fingerprinting from GC-FID and GC-MS coupled with chemometric techniques (discriminant analysis and principal component analysis) is used as a diagnostic tool to classify the types of oil polluting the water. Clustering and discrimination of oil spill compounds in the water from the actual site of oil spill events are divided into four groups viz. diesel, Heavy Fuel Oil (HFO), Mixture Oil containing Light Fuel Oil (MOLFO) and Waste Oil (WO) according to the similarity of their intrinsic chemical properties. Principal component analysis (PCA) demonstrates that diesel, HFO, MOLFO and WO are types of oil or oil products from complex oil mixtures with a total variance of 85.34% and are identified with various anthropogenic activities related to either intentional releasing of oil or accidental discharge of oil into the environment. Our results show that the use of chemometric techniques is significant in providing independent validation for classifying the types of spilled oil in the investigation of oil spill pollution in Malaysia. This, in consequence would result in cost and time saving in identification of the oil spill sources. Copyright © 2016. Published by Elsevier Ltd.

21 CFR 172.861 - Cocoa butter substitute from coconut oil, palm kernel oil, or both oils.

Science.gov (United States)

2010-04-01

... kernel oil, or both oils. 172.861 Section 172.861 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT... substitute from coconut oil, palm kernel oil, or both oils. The food additive, cocoa butter substitute from coconut oil, palm kernel oil, or both oils, may be safely used in food in accordance with the following...

Microwave remote sensing measurements of oil pollution on the ocean

Science.gov (United States)

Croswell, W. F.; Blume, H.-J. C.; Johnson, J. W.

1981-01-01

Microwave and optical remote sensors were flown over fresh and weathered crude oil released from a surface research vessel and also over a slick formed on the sea by frozen oleyl alcohol cubes released from a helicopter. For the crude oil experiments, microwave radiometric measurements at 1.43, 2.65, 22, and 31 GHz are reported, along with the variable incidence angle scattering measurements at 13.9 GHz. For these experiments, unusual depressions in the L-band brightness temperature were observed, possibly related to dispersants applied to the crude oil. Similar depressions, but with much larger values, were observed over the oleyl alcohol monomolecular slicks. Images obtained at 31 and 22 GHz were used to infer oil volume, yielding values which bound the known amounts spilled. Ku band measurements obtained in repeated passes over crude oil slicks are also discussed.

Determining the thermal and physicals properties of oil processing products

Directory of Open Access Journals (Sweden)

Viktoria I. Kryvda

2015-03-01

Full Text Available In the last decades both technological process’ improvement and primary energy resources saving are the main tasks of oil refineries. Using various oil products does impose an accurate knowledge of their properties. The dispersion analysis applied makes possible to construct a model simulating the primary oil refining products’ and raw materials’ thermal physical properties. As a result of data approximation there were obtained polynomials with coefficients differing from attributable to the studied oil products fractions. The research represents graphic dependences of thermal physical properties on temperature values for diesel oil fraction. The linear character of density and calorific capacity dependencies from temperature is represented with a proportional error in calculations. The relative minimum error is below 2% that confirms the implemented calculations’ adequacy. The resulting model can be used in calculations for further technological process improvements.

Infrared Spectroscopy of Bilberry Extract Water-in-Oil Emulsions: Sensing the Water-Oil Interface

Directory of Open Access Journals (Sweden)

Johannes Kiefer

2016-04-01

Full Text Available Water-in-oil (w/o emulsions are of great interest in many areas of the life sciences, including food technology, bioprocess engineering, and pharmaceuticals. Such emulsions are complex multi-component systems and the molecular mechanisms which lead to a stable emulsion are yet to be fully understood. In this work, attenuated total reflection (ATR infrared (IR spectroscopy is applied to a series of w/o emulsions of an aqueous anthocyanin-rich bilberry extract dispersed in a medium chain triglyceride (MCT oil phase. The content of the emulsifier polyglycerin-polyricinoleat (PGPR has been varied systematically in order to investigate whether or not its concentration has an impact on the molecular stabilization mechanisms. The molecular stabilization is accessed by a careful analysis of the IR spectrum, where changes in the vibrational frequencies and signal strengths indicate alterations of the molecular environment at the water/oil interface. The results suggest that adding emulsifier in excess of 1% by weight does not lead to an enhanced stabilization of the emulsion.

Rapid Formation of Microbe-Oil Aggregates and Changes in Community Composition in Coastal Surface Water Following Exposure to Oil and the Dispersant Corexit

Directory of Open Access Journals (Sweden)

Shawn M. Doyle

2018-04-01

Full Text Available During the Deepwater Horizon (DWH oil spill, massive quantities of oil were deposited on the seafloor via a large-scale marine oil-snow sedimentation and flocculent accumulation (MOSSFA event. The role of chemical dispersants (e.g., Corexit applied during the DWH oil spill clean-up in helping or hindering the formation of this MOSSFA event are not well-understood. Here, we present the first experiment related to the DWH oil spill to specifically investigate the relationship between microbial community structure, oil and Corexit®, and marine oil-snow in coastal surface waters. We observed the formation of micron-scale aggregates of microbial cells around droplets of oil and dispersant and found that their rate of formation was directly related to the concentration of oil within the water column. These micro-aggregates are potentially important precursors to the formation of larger marine oil-snow particles. Therefore, our observation that Corexit® significantly enhanced their formation suggests dispersant application may play a role in the development of MOSSFA events. We also observed that microbial communities in marine surface waters respond to oil and oil plus Corexit® differently and much more rapidly than previously measured, with major shifts in community composition occurring within only a few hours of experiment initiation. In the oil-amended treatments without Corexit®, this manifested as an increase in community diversity due to the outgrowth of several putative aliphatic- and aromatic-hydrocarbon degrading genera, including phytoplankton-associated taxa. In contrast, microbial community diversity was reduced in mesocosms containing chemically dispersed oil. Importantly, different consortia of hydrocarbon degrading bacteria responded to oil and chemically dispersed oil, indicating that functional redundancy in the pre-spill community likely results in hydrocarbon consumption in both undispersed and dispersed oils, but by different

Rapid Formation of Microbe-Oil Aggregates and Changes in Community Composition in Coastal Surface Water Following Exposure to Oil and the Dispersant Corexit.

Science.gov (United States)

Doyle, Shawn M; Whitaker, Emily A; De Pascuale, Veronica; Wade, Terry L; Knap, Anthony H; Santschi, Peter H; Quigg, Antonietta; Sylvan, Jason B

2018-01-01

During the Deepwater Horizon (DWH) oil spill, massive quantities of oil were deposited on the seafloor via a large-scale marine oil-snow sedimentation and flocculent accumulation (MOSSFA) event. The role of chemical dispersants (e.g., Corexit) applied during the DWH oil spill clean-up in helping or hindering the formation of this MOSSFA event are not well-understood. Here, we present the first experiment related to the DWH oil spill to specifically investigate the relationship between microbial community structure, oil and Corexit®, and marine oil-snow in coastal surface waters. We observed the formation of micron-scale aggregates of microbial cells around droplets of oil and dispersant and found that their rate of formation was directly related to the concentration of oil within the water column. These micro-aggregates are potentially important precursors to the formation of larger marine oil-snow particles. Therefore, our observation that Corexit® significantly enhanced their formation suggests dispersant application may play a role in the development of MOSSFA events. We also observed that microbial communities in marine surface waters respond to oil and oil plus Corexit® differently and much more rapidly than previously measured, with major shifts in community composition occurring within only a few hours of experiment initiation. In the oil-amended treatments without Corexit®, this manifested as an increase in community diversity due to the outgrowth of several putative aliphatic- and aromatic-hydrocarbon degrading genera, including phytoplankton-associated taxa. In contrast, microbial community diversity was reduced in mesocosms containing chemically dispersed oil. Importantly, different consortia of hydrocarbon degrading bacteria responded to oil and chemically dispersed oil, indicating that functional redundancy in the pre-spill community likely results in hydrocarbon consumption in both undispersed and dispersed oils, but by different bacterial taxa

Numerical study on oil supply system of a rotary compressor

International Nuclear Information System (INIS)

Wu, Jianhua; Wang, Gang

2013-01-01

The oil supply system is a crucial reliability issue for rotary compressors. This paper provides a general method for analyzing the oil supply system of a rotary compressor by using computational fluid dynamics (CFD). The process includes establishing the physical model, dividing computational grid, setting boundary conditions, calculating leakage rates through the roller end clearances, translating the dynamic issue into the static issue and so on. Validation of the rationality of the oil supply system model has been made by the measurement of the main bearing oil flow rates. The effects of operating conditions of the compressor, the oil level height of the oil sump and the main design parameters of the oil supply system on the oil supply characteristics are analyzed by numerical simulation. It is found that the main bearing oil flow rate varies circularly along with the rotation of the shaft. The shape and inclination angle of the spiral groove also influence the main bearing oil flow rate. The oil leakage rates through the roller end clearances depend largely on the operating conditions. In addition, the oil level height of the oil sump has a huge effect on the total oil flow rate. -- Highlights: • A CFD method for analyzing the oil supply system of rotary compressor is presented. • Leakage through the roller end clearances depends on the operating condition. • Groove shape and inclination angle are the main design parameters of spiral grooves. • A parabolic interface of oil and gas can be formed in the gallery of the shaft. • Single-flow model and steady solver can be applied to the oil supply system

PURIFICATION OF TRANSFORMER OIL in PT. PJB UP PAITON

OpenAIRE

Gusti Wahdaniyah*, Purnomo Tri Prasetyo, Arif Setiabudi, Totok R. Biyanto

2016-01-01

The purpose of this paper is to describe the filtration or purification of transformer oil. One of the main equipment in coal-fired power generation unit is transformer. When the transformer fail to operate properly, the continuity of distribution system become interrupted. As a part of transformer, transformer oil contribute the failure of transformer due to the aging. To solve this problem, several methods is applied starting from dehydration process, degasification process, oxidation remov...

Effect Of Gamma Irradiation On The Chemical Properties Of Olive And Linseed Oils During The Storage Period

International Nuclear Information System (INIS)

Farag, M.D.H.; Eweida, M.H.T.; Ali, H.E.; Refai, K.M.

2013-01-01

The quality of edible oil is usually determined in term of its quality constants and the change in these constants would affect the quality of the oil. Evaluation of gamma irradiation and storage period effects on olive and linseed oils was studied. The studied changes in the chemical properties for these oils were free fatty acid, peroxide value, thiobarbituric acid, iodine value and saponification value. The applied irradiation doses were 4, 6 and 8 kGy while the dose rate was 3.529 kGy/h at the time of experimentation. The non-irradiated oil samples were used as controls. The irradiated oil samples showed that free fatty acid, peroxide value and thiobarbituric acid were increased and the iodine value was decreased with increasing the doses of radiation and storage period while the saponification value did not change by changing the applied radiation doses. The statistical analysis of the data exhibited that there were non-significant effects in irradiated oils during the storage period. However, the values of chemical properties of non-irradiated and irradiated oil samples were still within the normal limits of edible oils recommended by the Egyptian Standard Specifications (2005 a, b)

Three different applications of genetic algorithm (GA) search techniques on oil demand estimation

International Nuclear Information System (INIS)

Canyurt, Olcay Ersel; Oztuerk, Harun Kemal

2006-01-01

This present study develops three scenarios to analyze oil consumption and make future projections based on the Genetic algorithm (GA) notion, and examines the effect of the design parameters on the oil utilization values. The models developed in the non-linear form are applied to the oil demand of Turkey. The GA Oil Demand Estimation Model (GAODEM) is developed to estimate the future oil demand values based on Gross National Product (GNP), population, import, export, oil production, oil import and car, truck and bus sales figures. Among these models, the GA-PGOiTI model, which uses population, GNP, oil import, truck sales and import as design parameters/indicators, was found to provide the best fit solution with the observed data. It may be concluded that the proposed models can be used as alternative solution and estimation techniques for the future oil utilization values of any country

Effects of oil transferred from incubating gulls to their eggs

Science.gov (United States)

King, K.A.; LeFever, C.A.

1979-01-01

No. 2 fuel oil, or water, was applied to the breast feathers of incubating laughing gulls trapped at their nest site on an island colony in Texas. Gulls were released after treatment and allowed to incubate their eggs for 5 days. Oil was transferred from the feathers of incubating adults to their eggs and resulted in 41% embryo mortality compared with 2% in controls.

1170-MW(t) HTGR-PS/C plant application study report: shale oil recovery application

International Nuclear Information System (INIS)

Rao, R.; McMain, A.T. Jr.

1981-05-01

The US has large shale oil energy resources, and many companies have undertaken considerable effort to develop economical means to extract this oil within environmental constraints. The recoverable shale oil reserves in the US amount to 160 x 10 9 m 3 (1000 x 10 9 bbl) and are second in quantity only to coal. This report summarizes a study to apply an 1170-MW(t) high-temperature gas-cooled reactor - process steam/cogeneration (HTGR-PS/C) to a shale oil recovery process. Since the highest potential shale oil reserves lie in th Piceance Basin of Western Colorado, the study centers on exploiting shale oil in this region

Bioremediation of marine oil pollution

International Nuclear Information System (INIS)

Gutnick, D.L.

1991-11-01

An assessment is presented of the scientific and technological developments in the area of bioremediation and biodegradation of marine oil pollution. A number of allied technologies are also considered. The basic technology in bioremediation involves adding fertilizers to an oil spill to enhance the natural process of oil biodegradation. Bioremediation can be applied to open systems such as beach or land spills, or in closed and controlled environments such as storage containers, specially constructed or modified bioreactors, and cargo tanks. The major advantage of using closed environments is the opportunity to control the physical and nutritional parameters to optimize the rate of biodegradation. An evaluation of the state of the art of bioremediation in Canada is also included. Recommendations are made to involve the Canadian Transportation Development Centre in short-term research projects on bioremediation. These projects would include the use of a barge as a mobile bioreactor for the treatment of off-loaded oily waste products, the use of in-situ bioremediation to carry out extensive cleaning, degassing, and sludge remediation on board an oil tanker, and the use of a barge as a mobile bioreactor and facility for the bioremediation of bilges. 51 refs., 4 figs., 14 tabs

Bioremediation of oil-contaminated sites

Energy Technology Data Exchange (ETDEWEB)

Balba, T. [Conestoga-Rovers and Associates, Calgary, AB (Canada)

2003-07-01

One of the most prevalent contaminants in subsurface soil and groundwater are petroleum hydrocarbons. This paper presented bioremediation of petroleum hydrocarbons as one of the most promising treatment technologies. Petroleum hydrocarbons are categorized into four simple fractions: saturates, aromatics, resins, and asphaltenes. Bioremediation refers to the treatment process whereby contaminants are metabolized into less toxic or nontoxic compounds by naturally occurring organisms. The various strategies include: use of constitutive enzymes, enzyme induction, co-metabolism, transfer of plasmids coding for certain metabolic pathways, and production of biosurfactants to enhance bioavailability of hydrophobic compounds. Three case studies were presented: (1) bioremediation of heavy oils in soil at a locomotive maintenance yard in California, involving a multi-step laboratory treatability study followed by a field demonstration achieving up to 94 per cent removal of TPH in less than 16 weeks, (2) bioremediation of light oils in soil at an oil refinery in Germany where a dual process was applied (excavation and in-situ treatment), achieving an 84 per cent reduction within 24 weeks, and (3) bioremediation of oil-contaminated desert soil in Kuwait which involved landfarming, composting piles, and bioventing soil piles, achieving an 80 per cent reduction within 12 months. 7 refs., 1 tab., 3 figs.

Bioremediation of marine oil pollution

Energy Technology Data Exchange (ETDEWEB)

Gutnick, D L

1991-11-01

An assessment is presented of the scientific and technological developments in the area of bioremediation and biodegradation of marine oil pollution. A number of allied technologies are also considered. The basic technology in bioremediation involves adding fertilizers to an oil spill to enhance the natural process of oil biodegradation. Bioremediation can be applied to open systems such as beach or land spills, or in closed and controlled environments such as storage containers, specially constructed or modified bioreactors, and cargo tanks. The major advantage of using closed environments is the opportunity to control the physical and nutritional parameters to optimize the rate of biodegradation. An evaluation of the state of the art of bioremediation in Canada is also included. Recommendations are made to involve the Canadian Transportation Development Centre in short-term research projects on bioremediation. These projects would include the use of a barge as a mobile bioreactor for the treatment of off-loaded oily waste products, the use of in-situ bioremediation to carry out extensive cleaning, degassing, and sludge remediation on board an oil tanker, and the use of a barge as a mobile bioreactor and facility for the bioremediation of bilges. 51 refs., 4 figs., 14 tabs.

Fate of dispersed marine fuel oil in sediment under pre-spill application strategy

International Nuclear Information System (INIS)

Jian Hua

2004-01-01

A comparison of the movement of dispersed oil in marine sediment under two dispersant application scenarios, applied prior to and after oil being spilled overboard, was examined. The pre-spill application scenario caused much less oil to be retained in the top sediment than post-spill scenario. The difference in oil retention in the top sediment between pre- and post-spill application scenario increased with increase in fuel oil temperature. For fuel oil above 40 o C, the difference in the effect of pre-spill application strategy under various water temperatures was negligible. When soap water was used as replacement for chemical dispersant, almost one-half as much oil was retained in the top sediment as that when using chemical dispersant. The adsorption of dispersed oil to the top sediment was almost proportionally decreased with doubling of soap dosage. (Author)

NMR and Chemometric Characterization of Vacuum Residues and Vacuum Gas Oils from Crude Oils of Different Origin

Directory of Open Access Journals (Sweden)

Jelena Parlov Vuković

2015-03-01

Full Text Available NMR spectroscopy in combination with statistical methods was used to study vacuum residues and vacuum gas oils from 32 crude oils of different origin. Two chemometric metodes were applied. Firstly, principal component analysis on complete spectra was used to perform classification of samples and clear distinction between vacuum residues and vacuum light and heavy gas oils were obtained. To quantitatively predict the composition of asphaltenes, principal component regression models using areas of resonance signals spaned by 11 frequency bins of the 1H NMR spectra were build. The first 5 principal components accounted for more than 94 % of variations in the input data set and coefficient of determination for correlation between measured and predicted values was R2 = 0.7421. Although this value is not significant, it shows the underlying linear dependence in the data. Pseudo two-dimensional DOSY NMR experiments were used to assess the composition and structural properties of asphaltenes in a selected crude oil and its vacuum residue on the basis of their different hydrodynamic behavior and translational diffusion coefficients. DOSY spectra showed the presence of several asphaltene aggregates differing in size and interactions they formed. The obtained results have shown that NMR techniques in combination with chemometrics are very useful to analyze vacuum residues and vacuum gas oils. Furthermore, we expect that our ongoing investigation of asphaltenes from crude oils of different origin will elucidate in more details composition, structure and properties of these complex molecular systems.

Quantification of rice bran oil in oil blends

Energy Technology Data Exchange (ETDEWEB)

Mishra, R.; Sharma, H. K.; Sengar, G.

2012-11-01

Blends consisting of physically refined rice bran oil (PRBO): sunflower oil (SnF) and PRBO: safflower oil (SAF) in different proportions were analyzed for various physicochemical parameters. The quantification of pure rice bran oil in the blended oils was carried out using different methods including gas chromatographic, HPLC, ultrasonic velocity and methods based on physico-chemical parameters. The physicochemical parameters such as ultrasonic velocity, relative association and acoustic impedance at 2 MHz, iodine value, palmitic acid content and oryzanol content reflected significant changes with increased proportions of PRBO in the blended oils. These parameters were selected as dependent parameters and % PRBO proportion was selected as independent parameters. The study revealed that regression equations based on the oryzanol content, palmitic acid composition, ultrasonic velocity, relative association, acoustic impedance, and iodine value can be used for the quantification of rice bran oil in blended oils. The rice bran oil can easily be quantified in the blended oils based on the oryzanol content by HPLC even at a 1% level. The palmitic acid content in blended oils can also be used as an indicator to quantify rice bran oil at or above the 20% level in blended oils whereas the method based on ultrasonic velocity, acoustic impedance and relative association showed initial promise in the quantification of rice bran oil. (Author) 23 refs.

Estimating core inflation : the role of oil price shocks and imported inflation

OpenAIRE

Bjørnland, Hilde Christiane

1997-01-01

This paper calculates core inflation, by imposing long run restrictions on a structural vector autoregression (VAR) model containing the growth rate of output, inflation and oil prices. Core inflation is identified as that component in inflation that has no long run effect on output. No restrictions are placed on the response of output and inflation to the oil price shocks. The analysis is applied to Norway and the United Kingdom, both oil producing OECD countries. A model that ...

Influence of the processed sunflower oil on the cement properties

Science.gov (United States)

Fleysher, A. U.; Tokarchuk, V. V.; Sviderskiy, V. A.

2015-01-01

Used oils (vegetable oil, animal oil, engine oil, etc.), which are essentially industrial wastes, have found application as secondary raw materials in some braches of industry. In particular, the only well-known and commonly-used way of utilizing wastes of vegetable oils is to apply them as raw materials in the production of biodiesel. The goal of the present study is to develop a conceptually new way of vegetable oil wastes utilization in the building industry. The test admixture D-148 was obtained from the processing of wastes of sunflower oil and it mainly consists of fatty acid diethanolamide. The test admixture was added to the cement system for the purpose of studying its influence on water demand, flowability, setting times, compressive strength and moisture adsorption. The test admixture D-148 at the optimal content 0. 2 weight % causes 10% decrease in water demand, 1.7 time increase in flowability (namely spread diameter), 23% increase in grade strength and 34% decrease in moisture adsorption. The results of the present investigation make it possible to consider the final product of the waste sunflower oil processing as multifunctional plasticizing-waterproofing admixture.

Review of Heterogeneous Catalysts for Catalytically Upgrading Vegetable Oils into Hydrocarbon Biofuels

Directory of Open Access Journals (Sweden)

Xianhui Zhao

2017-03-01

Full Text Available To address the issues of greenhouse gas emissions associated with fossil fuels, vegetable oilseeds, especially non-food oilseeds, are used as an alternative fuel resource. Vegetable oil derived from these oilseeds can be upgraded into hydrocarbon biofuel. Catalytic cracking and hydroprocessing are two of the most promising pathways for converting vegetable oil to hydrocarbon biofuel. Heterogeneous catalysts play a critical role in those processes. The present review summarizes current progresses and remaining challenges of vegetable oil upgrading to biofuel. The catalyst properties, applications, deactivation, and regeneration are reviewed. A comparison of catalysts used in vegetable oil and bio-oil upgrading is also carried out. Some suggestions for heterogeneous catalysts applied in vegetable oil upgrading to improve the yield and quality of hydrocarbon biofuel are provided for further research in the future.

Oil spills

International Nuclear Information System (INIS)

Katsouros, M.H.

1992-01-01

The world annually transports 1.7 billion tons of oil by sea, and oil spills, often highly concentrated discharges, are increasing from a variety of sources. The author discusses sources of oils spills: natural; marine transportation; offshore oil production; atmospheric sources; municipal industrial wastes and runoff. Other topics include: the fate of the spilled oil; the effects of the oil; the response to oil spills; and prevention of oil spills. 30 refs., 1 fig., 4 tabs

A critical review of IEA's oil demand forecast for China

International Nuclear Information System (INIS)

Nel, Willem P.; Cooper, Christopher J.

2008-01-01

China has a rapidly growing economy with a rapidly increasing demand for oil. The International Energy Agency (IEA) investigated possible future oil demand scenarios for China in the 2006 World Energy Outlook. The debate on whether oil supplies will be constrained in the near future, because of limited new discoveries, raises the concern that the oil industry may not be able to produce sufficient oil to meet this demand. This paper examines the historical relationship between economic growth and oil consumption in a number of countries. Logistic curve characteristics are observed in the relationship between per capita economic activity and oil consumption. This research has determined that the minimum statistical (lower-bound) annual oil consumption for developed countries is 11 barrels per capita. Despite the increase reported in total energy efficiency, no developed country has been able to reduce oil consumption below this lower limit. Indeed, the IEA projections to 2030 for the OECD countries show no reduction in oil demand on a per capita basis. If this lower limit is applied to China, it is clear that the IEA projections for China are under-estimating the growth in demand for oil. This research has determined that this under-estimation could be as high as 10 million barrels per day by 2025. If proponents of Peak Oil such as Laherrere, Campbell and Deffeyes are correct about the predicted peak in oil production before 2020 then the implications of this reassessment of China's oil demand will have profound implications for mankind

The effect of global oil price shocks on China's metal markets

International Nuclear Information System (INIS)

Zhang, Chuanguo; Tu, Xiaohua

2016-01-01

This paper investigated the impacts of global oil price shocks on the whole metal market and two typical metal markets: copper and aluminum. We applied the autoregressive conditional jump intensity (ARJI) model, combining with the generalized conditional heteroscedasticity (GRACH) method, to describe the volatility process and jump behavior in the global oil market. We separated the oil price shocks into positive and negative parts, to analyze whether oil price volatility had symmetric impacts on China’s metal markets. We further used the likelihood ratio test to examine the symmetric effect of oil price shocks. In addition, we considered the jump behavior in oil prices as an input factor to investigate how China’s metal markets are affected when jumps occur in the global oil market, in contrast to the existing research paying little attention to this issue. Our results indicate that crude oil price shocks have significant impacts on China's metal markets and the impacts are symmetric. When compared with aluminum, copper is more easily affected by oil price shocks. - Highlights: • We investigated the effect of oil price shocks on China’s metal markets. • The oil price shocks had significant impacts on China's metal markets • The oil price shocks on China's metal markets were symmetric. • Copper is more easily affected by oil price shocks than aluminum.

A Case Study of Offshore Advection of Boundary Layer Rolls over a Stably Stratified Sea Surface

Directory of Open Access Journals (Sweden)

Nina Svensson

2017-01-01

Full Text Available Streaky structures of narrow (8-9 km high wind belts have been observed from SAR images above the Baltic Sea during stably stratified conditions with offshore winds from the southern parts of Sweden. Case studies using the WRF model and in situ aircraft observations indicate that the streaks originate from boundary layer rolls generated over the convective air above Swedish mainland, also supported by visual satellite images showing the typical signature cloud streets. The simulations indicate that the rolls are advected and maintained at least 30–80 km off the coast, in agreement with the streaks observed by the SAR images. During evening when the convective conditions over land diminish, the streaky structures over the sea are still seen in the horizontal wind field; however, the vertical component is close to zero. Thus advected feature from a land surface can affect the wind field considerably for long times and over large areas in coastal regions. Although boundary layer rolls are a well-studied feature, no previous study has presented results concerning their persistence during situations with advection to a strongly stratified boundary layer. Such conditions are commonly encountered during spring in coastal regions at high latitudes.

Preparation of novel cotton fabric composites with pH controlled switchable wettability for efficient water-in-oil and oil-in-water emulsions separation

Science.gov (United States)

Wang, Qian; Wu, Jianning; Meng, Guihua; Wang, Yixi; Liu, Zhiyong; Guo, Xuhong

2018-06-01

The wetting materials with the ability of controllable oil/water separation have drawn more and more public attention. In this article, the novel cotton fabric (CF) with pH controlled wettability transition was designed by a simple, environmentally friendly coating copolymer/SiO2 nanoparticles, poly(heptadecafluorodecyl methacrylate- co-3-trimethoxysilylpropyl methacrylate- co-2-vinilpiridine) (PHDFDMA- co-PTMSPMA- co-P2VP). Furthermore, the structures and morphologies of coated CF were confirmed by Fourier transform infrared spectroscopy (FTIR), NMR, GPC, scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). The coated CF exhibits switchable wettability between superhydrophobicity and superhydrophilicity via adjusting pH value. When the coated CF is placed in the neutral aqueous (pH = 7.0), it is superhydrophobic in the air and superoleophilic. It allows oil to go through but blocking water. However, in acidic aqueous environment (pH = 3.0), it turns superhydrophilic and underwater superoleophobic, which allows water to penetrate but blocking oil. Therefore, the coated CF could be applied to separate oil/water mixtures, ternary oil/water/water mixtures continuously and different surfactant stabilized emulsions (oil-in-water, water-in-oil) and displays the superior separation capacity for oil-water mixtures with a high efficiency of 99.8%. Moreover, the cycling tests demonstrate that the coated CF possesses excellent recyclability and durability. Such an eminent, controllable water/oil permeation feature makes coated CF could be selected as an ideal candidate for oil/water separation.

Diesel fuel oil for increasing mountain pine beetle mortality in felled logs

Science.gov (United States)

S. A. Mata; J. M. Schmid; D. A. Leatherman

2002-01-01

Diesel fuel oil was applied to mountain pine beetle (Dendroctonus ponderosae Hopkins) infested bolts of ponderosa pine (Pinus ponderosa Lawson) in early June. Just prior to the fuel oil application and 6 weeks later, 0.5 ft2 bark samples were removed from each bolt and the numbers of live beetles counted....

Contact Hwersensitaity to Mustard Khal and Mustard Oil

OpenAIRE

J S Pasricha; Ramji Gupta; S K Gupta

1985-01-01

This report describes 2 females patients having contact dermatitis due to mustard khal the residue of,mustard seeds after the oil hasbeen extracted out. The dermatitis was caused by mbdng mustard khal with the cattle feed and was occurring on the hands and forearms, though the face, ear lobules and neck were also mvolved because of the practice of applying mustard oil on the hair. Patch tests were positive with the mustard khal and its fractionation products in both the patients and with must...

Mineral content of insect infested stored legumes treated with edible oils.

Science.gov (United States)

Modgil, R

2000-12-01

Mineral content of three insect (pulse beetle, Callosobruchus chinensis L.) infested legumes viz. chick pea, mung pea and pigeon pea stored for six months and treated with three edible oils viz. groundnut, mustard and coconut oil has been studied. With increase in storage period significant increase in calcium, phosphorus and iron content of untreated legumes was observed. After three months of storage slight increase in three minerals was observed in the legumes treated with coconut oil which continued till the end of sixth months as compared to other two oil treated counterparts. The storage period was associated with insect infestation which in turn influenced the mineral content of legumes. Ground nut and mustard oils were able to protect legumes for six months against insect infestation when applied in small amounts (0.5%). Whereas coconut oil had protective effect against insect infestation for four months only.

Material flow analysis for resource management towards resilient palm oil production

Science.gov (United States)

Kamahara, H.; Faisal, M.; Hasanudin, U.; Fujie, K.; Daimon, H.

2018-03-01

Biomass waste generated from palm oil mill can be considered not only as the feedstock of renewable energy but also as the nutrient-rich resources to produce organic fertilizer. This study explored the appropriate resource management towards resilient palm oil production by applying material flow analysis. This study was conducted based on two palm oil mills in Lampung, Indonesia. The results showed that the empty fruit bunch (EFB) has the largest potential in terms of amount and energy among the biomass waste. The results also showed that the palm oil mills themselves had already self-managed their energy consumption thatwas obtained from palm kernel shell and palm press fiber. Finally, this study recommended the several utilization options of EFB for improvement of soil sustainability to contribute towards resilient palm oil production.

ENCAPSULATION OF HYPERICUM PERFORATUM L., JOJOBA OIL AND JASMINE OIL BY SPRAY DRYING AND THEIR APPLICATIONS IN TEXTILES

Directory of Open Access Journals (Sweden)

ÖGE Arzu

2017-05-01

Full Text Available Microencapsulation is a technique that allows liquid or solid agents, such as pharmaceutical agents, pesticides, insect repellent agents, dyes, cosmetics and fragrances, to be encapsulated by a suitable barrier wall. Liquid or solid agents that are encapsulated are called core material. The importance of functional finishes have been increasing rapidly in the World. Microencapsulation is an alternative way to achieve the functional finishes because of their unique properties, such as controlled release, protection against to hazardous and destructive media, and providing higher surface area. In this study, jojoba, jasmine and St. John's Wort oils, were encapsulated according to spray drying method. St. John's Wort and jojoba oils were used at 1:1 ratio as fixed oil. Jasmine essential oil was added to fixed oil mixture at two different ratios. After preparing the core mixture, encapsulation studies were performed three different core : wall ratios. Morphological analyses of microcapsules were carried out using SEM (Scanning Electron Microscope. FTIR spectroscopy spectrums of microcapsules were determined (Fourier Transform Infrared. Particle size distribution microcapsules were analyzed by laser scattering measurement method. DSC (Differential Scanning Calorimetry thermographs of microcapsules were obtained. All microcapsules were applied to 100% cotton knitted fabrics. Strength to washing of fabrics were observed by SEM micrographs.

Hydroprocesssing of light gas oil - rape oil mixtures

Energy Technology Data Exchange (ETDEWEB)

Walendziewski, Jerzy; Stolarski, Marek; Luzny, Rafal; Klimek, Bartlomiej [Faculty of Chemistry, Wroclaw University of Technology, ul. Gdanska 7/9, 50-310 Wroclaw (Poland)

2009-05-15

Two series of experiments of hydroprocessing of light gas oil - rape oil mixtures were carried out. The reactor feed was composed of raw material: first series - 10 wt.% rape oil and 90 wt.% of diesel oil; second series - 20 wt.% rape oil and 80 wt.% of diesel oil. Hydroprocessing of both mixtures was performed with the same parameter sets, temperature (320, 350 and 380 C), hydrogen pressure 3 and 5 MPa, LHSV = 2 h{sup -} {sup 1} and hydrogen feed ratio of 500 Nm{sup 3}/m{sup 3}. It was stated that within limited range it is possible to control vegetable oil hydrogenolysis in the presence of light gas oil fraction (diesel oil boiling range) through the proper selection of the process parameters. Hydrogenolysis of ester bonds and hydrogenation of olefinic bonds in vegetable oils are the main reactions in the process. Basic physicochemical properties of the obtained hydroprocessed products are presented. (author)

Water control for enhanced oil recovery

Energy Technology Data Exchange (ETDEWEB)

Cole, R.C.; Mody, B.; Pace, J.

1981-11-01

Gains in recovery efficiency in W. Texas oil and gas fields have been realized as a result of applying 4 different chemical processes, either singly or in combination. Each of the 4 chemical processes has been tailored to meet specific reservoir requirements. Complete plugging of high flow capacity channels can be accomplished, and the high water production portion of a producing zone can be sealed by injection of gel-forming chemicals into the matrix. Both floodwater diversion and water-oil mobility ratio improvement can be attained by in situ polymerization of a one-stage polymer bank in the reservoir. In producing wells, the water-oil production ratio can be favorably changed by treating certain formulations with a nonplugging polymer which tends to restrict water flow but not oil. One feature which each of the 4 processes has in common is the ability to invade deeply into matrix which may produce long lasting results. A description of each process is presented with various placement techniques used to obtain optimum results. Data from fields which have benefited from these treatments are presented. The work describes what may be expected with each of these proven processes based on field results.

Quality of underground water and hydro-geological situation caused by oil exploitation in the area of Kikinda

Directory of Open Access Journals (Sweden)

Pašić Milana

2010-01-01

Full Text Available Numerous oil fields were discovered in the area of North Banat and its regional centre, the city of Kikinda. These oil fields were explored and exploited in the second half of the XX century. Oil rigs in the area of the city zone can endanger the environment, as well as the quality of life of the citizens. In order to discover the presence of polycyclic aromatic hydrocarbon we have applied GC/MSD technique, whereas we have applied GC/MSD Purge and trap. technique to discover the presence of aromatic hydrocarbon. Chemical analyses of water samples from the area of Kikinda did nit prove that underground water was polluted with oil. .

Falling R and D but stable investments by oil companies, why? A study on R and D and investment in fixed assets in the oil industry

International Nuclear Information System (INIS)

Creusen, H.; Minne, B.

2000-04-01

In the last decade the world-wide research expenditures of the major oil companies have dropped. This is remarkable since their investments in fixed assets remained stable. This study reveals that the level of fixed investments particularly depend on their financial strength, while R and D mainly relates to competitors' research and common expectations. The decline in R and D is initiated by common expectations. In the mature oil industry, companies foresee diminishing research potential within the current technology. This is also confirmed by the declining number of patent applications. The high risks of research on renewable energy may lead to wait and see behaviour instead of new research initiatives. Actually, oil companies have hardly applied for patents on renewable energy. The R and D decline is intensified by a dwindling R and D-race, which is due to a large overlap in research topics. The companies protect their research results because they largely compete on their unique technologies which embody their research results. The research overlap appears from patents: the oil companies apply for patents in exactly the same patent classes. 19 refs

Application of a pneumatic flotation process for the treatment of oil-burdened industrial effluents

International Nuclear Information System (INIS)

Kinabo, C.

1993-01-01

Different industrial waste waters containing oil emulsions were investigated using pneumatic flotation techniques. The separation efficiency is determined by the zeta potential of the oil/water emulsion. The electrophoretic measurements indicated that, the iep of the emulsion lies within the region of pH 5. Within this pH region it was possible to reduce the oil mud to a minimum level from the waste water using flotation. The laboratory flotation results showed the rest oil concentration amounts to 0.2 and 0.01% depending on the loading grade of oil in the waste water. Applying an emulsion with an oil content of 12%, it was possible to achieve a product in industrial scale with a rest oil concentration of 0.08%. (orig.) [de

Biodiesel from waste cooking oils via direct sonication

International Nuclear Information System (INIS)

Gude, Veera Gnaneswar; Grant, Georgene Elizabeth

2013-01-01

Highlights: • Thermal effects of direct sonication on transesterification reaction were studied. • Ultrasonics may effectively transesterify waste oils without external heating. • Intense mixing with temperature rise completes transesterification instantly. • Plug flow process reactor design with ultrasound may prove energy efficient. • Process optimization and biodiesel conversion analysis was presented. - Abstract: This study investigates the effect of direct sonication in conversion of waste cooking oil into biodiesel. Waste cooking oils may cause environmental hazards if not disposed properly. However, waste cooking oils can serve as low-cost feedstock for biodiesel production. Ultrasonics, a non-conventional process technique, was applied to directly convert waste cooking oil into biodiesel in a single step. Ultrasonics transesterify waste cooking oils very efficiently due to increased mass/heat transfer phenomena and specific thermal/athermal effects at molecular levels. Thus, energy and chemical consumption in the overall process is greatly reduced compared to conventional biodiesel processes. Specific to this research, thermal effects of ultrasonics in transesterification reaction without external conventional heating along with effects of different ultrasonic, energy intensities and energy density are reported. Optimization of process parameters such as methanol to oil ratio, catalyst concentration and reaction time are also presented. It was observed that small reactor design such as plug-flow or contact-type reactor design may improve overall ultrasonic utilization in the transesterification reaction due to increased energy density and ultrasonic intensity

Portable detection system of vegetable oils based on laser induced fluorescence

Science.gov (United States)

Zhu, Li; Zhang, Yinchao; Chen, Siying; Chen, He; Guo, Pan; Mu, Taotao

2015-11-01

Food safety, especially edible oils, has attracted more and more attention recently. Many methods and instruments have emerged to detect the edible oils, which include oils classification and adulteration. It is well known than the adulteration is based on classification. Then, in this paper, a portable detection system, based on laser induced fluorescence, is proposed and designed to classify the various edible oils, including (olive, rapeseed, walnut, peanut, linseed, sunflower, corn oils). 532 nm laser modules are used in this equipment. Then, all the components are assembled into a module (100*100*25mm). A total of 700 sets of fluorescence data (100 sets of each type oil) are collected. In order to classify different edible oils, principle components analysis and support vector machine have been employed in the data analysis. The training set consisted of 560 sets of data (80 sets of each oil) and the test set consisted of 140 sets of data (20 sets of each oil). The recognition rate is up to 99%, which demonstrates the reliability of this potable system. With nonintrusive and no sample preparation characteristic, the potable system can be effectively applied for food detection.

Observation and optical implications of oil dewetting patterns in electrowetting displays

International Nuclear Information System (INIS)

Sun Bo; Heikenfeld, Jason

2008-01-01

Growth of surface instabilities leading to periodic oil patterns in electrowetting display pixels has been experimentally observed. In the electrowetting display pixels, an electrical potential ranging between 0 V and 80 V is applied among a water electrode, dielectric layers consisting of an oil film, fluoropolymer, Parylene C and a lower electrode. As predicted by spinodal dewetting theory, application of electromechanical pressure to the oil film causes the film to dewet into a periodic arrangement of oil droplets. The separation distance, or wavelength, for the dewetted oil droplets decreases with increasing voltage or with decreasing oil film thickness. Various test voltages of 20–80 V and oil thicknesses values of 3.3–8.9 µm were shown to experimentally generate dewetting wavelengths ranging from 10's to 100's of µm. An increased number of oil droplets inside the display pixel decreases the maximum display transmission or reflection proportional to the cube root of the number of droplets. This work therefore provides a means to further understand oil film dewetting in electrowetting display pixels and explains the implications of the dewetting pattern on display optical performance

Oil Spills

Science.gov (United States)

... up. How Oil Harms Animals and Plants in Marine Environments In general, oil spills can affect animals and plants in two ways: from the oil ... up. How Oil Harms Animals and Plants in Marine Environments In general, oil spills can affect animals and plants in two ways: from the oil ...

Chemical compositions and antioxidant activity of Heracleum persicum essential oil

Directory of Open Access Journals (Sweden)

Maryam Gharachorloo

2018-02-01

Full Text Available ABSTRACT In this study essential oil of the aerial parts of Heracleum persicum a spice widely used in Iran was isolated by conventional hydrodistillation (HD and microwave-assisted hydrodistillation (MAHD techniques. The extraction yield was determined and the chemical compositions of essential oils were identified by the application of gas chromatography/mass spectrometry (GC/MS. The antioxidant activity was determined by two different methods: 1,1-diphenyl-2-picrylhydrazyl (DPPH free radical scavenging and oven test methods. Although the main compounds of essential oils by the both extraction methods were similar, the essential oil extracted by HD with lower extraction efficiency showed more diverse compounds. The evaluation of antioxidant activity of the essential oil measured by delay in sunflower oil oxidation indicated that the antioxidant activity was dependent on the concentration which increased when higher concentrations of the essential oils were applied. The results of DPPH radical assay also indicated that the percentage of inhibition increased with increasing of essential oil concentration and IC50 value for essential oil extracted by MAHD method was obtained 1.25 mg/mL. Therefore the Heracleum persicum essential oil might be recommended for use as a flavoring agent and a source of natural antioxidants in functional foods, formulation of the supplements and in medicinal due to numerous pharmacological activities.

A laboratory study of particulate and gaseous emissions from crude oil and crude oil-dispersant contaminated seawater due to breaking waves

Science.gov (United States)

Afshar-Mohajer, Nima; Li, Cheng; Rule, Ana M.; Katz, Joseph; Koehler, Kirsten

2018-04-01

Crude oil spill incidents occur frequently causing a verity of occupational, ecological and environmental problems. Dispersants are applied to enhance the dispersion rate of crude oil slicks into the water column. In this study, the aerosol size distribution from 10 nm to 20 μm, total particle-bound aromatic hydrocarbons (pPAH) and volatile organic compounds (VOCs) are measured in a 6 x 0.3 x 0.6 m tank as plunging breaking waves entrain oil slicks. The experiments are performed for seawater with slicks of crude oil, crude oil-dispersant mixture and dispersant only. The measurements investigate the effects of wave energy and slick properties on the temporal evolution of the emissions. The total number concentrations of particles originating from the oil-dispersant mixture are 1-2 orders of magnitude higher than those of crude oil across the entire nano-scale range, reaching 100x for 20 nm particles. Conversely, the differences in concentration are small in the micron range. The average concentrations of pPAH are variable but similar (150-270 ng/m3). The VOC concentrations for crude oil-dispersant mixtures are 2-3 times lower than those of crude oil, presumably due to the surfactant effect on mass diffusion. The drastic increase in ultrafine particle concentrations may raise concerns about effects of inhalation by cleanup workers and downstream communities though VOC emissions reduce. Findings through this study provide insight into how the spray of dispersant may change the ratio of airborne particulate matter and VOC emissions from seawater due to natural processes.

Mathematical modelling of oil spill fate and transport in the marine environment incorporating biodegradation kinetics of oil droplets

Science.gov (United States)

Spanoudaki, Katerina

2016-04-01

, biodegradation) of each component is tracked separately. Biodegradation of oil droplets is modelled by Monod kinetics. The kinetics of oil particles size reduction due to the microbe-mediated degradation at water-oil particle interface is represented by the shrinking core model. In order to test the performance of the modified MEDSLIK-II model, it has been applied to a test case built-in the original code. The total fate of the oil spill is simulated both without biodegradation kinetics and when biodegradation is taken into account, for reasons of comparison. Several parameters that control biodegradation rate, including initial oil concentration and composition, size distribution of oil droplets and initial microbial concentration have been investigated. This upgraded version of MEDSLIK-II can be useful not only for predicting the transport and fate of spilled oil in the short term but also for evaluating different bioremediation strategies and risk assessment for the mid- and long term. Acknowledgements: The financial support by the EU project DECATASTROPHIZE: Use of SDSS and MCDA to Prepare for Disasters or Plan for Multiple Hazards, GA no. ECHO/SUB/2015/713788/PREP02, is greatly acknowledged.

Application of Multivariate Statistical Analysis to Biomarkers in Se-Turkey Crude Oils

Science.gov (United States)

Gürgey, K.; Canbolat, S.

2017-11-01

Twenty-four crude oil samples were collected from the 24 oil fields distributed in different districts of SE-Turkey. API and Sulphur content (%), Stable Carbon Isotope, Gas Chromatography (GC), and Gas Chromatography-Mass Spectrometry (GC-MS) data were used to construct a geochemical data matrix. The aim of this study is to examine the genetic grouping or correlations in the crude oil samples, hence the number of source rocks present in the SE-Turkey. To achieve these aims, two of the multivariate statistical analysis techniques (Principle Component Analysis [PCA] and Cluster Analysis were applied to data matrix of 24 samples and 8 source specific biomarker variables/parameters. The results showed that there are 3 genetically different oil groups: Batman-Nusaybin Oils, Adıyaman-Kozluk Oils and Diyarbakir Oils, in addition to a one mixed group. These groupings imply that at least, three different source rocks are present in South-Eastern (SE) Turkey. Grouping of the crude oil samples appears to be consistent with the geographic locations of the oils fields, subsurface stratigraphy as well as geology of the area.

APPLICATION OF MULTIVARIATE STATISTICAL ANALYSIS TO BIOMARKERS IN SE-TURKEY CRUDE OILS

Directory of Open Access Journals (Sweden)

K. Gürgey

2017-11-01

Full Text Available Twenty-four crude oil samples were collected from the 24 oil fields distributed in different districts of SE-Turkey. API and Sulphur content (%, Stable Carbon Isotope, Gas Chromatography (GC, and Gas Chromatography-Mass Spectrometry (GC-MS data were used to construct a geochemical data matrix. The aim of this study is to examine the genetic grouping or correlations in the crude oil samples, hence the number of source rocks present in the SE-Turkey. To achieve these aims, two of the multivariate statistical analysis techniques (Principle Component Analysis [PCA] and Cluster Analysis were applied to data matrix of 24 samples and 8 source specific biomarker variables/parameters. The results showed that there are 3 genetically different oil groups: Batman-Nusaybin Oils, Adıyaman-Kozluk Oils and Diyarbakir Oils, in addition to a one mixed group. These groupings imply that at least, three different source rocks are present in South-Eastern (SE Turkey. Grouping of the crude oil samples appears to be consistent with the geographic locations of the oils fields, subsurface stratigraphy as well as geology of the area.

Review of oil families and their petroleum systems of the Williston Basin

Science.gov (United States)

Lillis, Paul G.

2013-01-01

The petroleum system concept was first applied in 1974 (Dow/Williams) to identify three oil systems in the Williston Basin, and recent studies have expanded the number to at least nine. This paper reviews the petroleum geochemistry, oil-oil, and oil-source correlations of the oil systems of the Williston Basin, providing a new perspective and some new findings. Petroleum systems with a known source (documented oil-source correlation) include the Red River (Ordovician), Winnipegosis (Devonian), Bakken (Devonian-Mississippian), Madison (Mississippian), and Tyler (Pennsylvanian) systems. Petroleum systems with an identified source rock but no documented oil-source correlation are considered hypothetical and include the Winnipeg (Ordovician), Duperow (Devonian), and Birdbear (Devonian). The Deadwood (Cambrian-Ordovician) petroleum system is speculative because a good oil-prone source rock has not been identified. The stratigraphic distribution of the oil families from each system is generally limited to the same formation from which they were sourced due to efficient seals and a paucity of vertical migration pathways, but some notable exceptions do occur.

Improving the efficiency of photovoltaic (PV) panels by oil coating

International Nuclear Information System (INIS)

Abd-Elhady, M.S.; Fouad, M.M.; Khalil, T.

2016-01-01

Highlights: • It is possible to improve the efficiency of PV panels by increasing the amount of light transmitted to the panel. • Coating PV panels by a fine layer of Labovac oil increases the amount of sun light transmitted to the panel. • Coating PV panels by a fine layer of Labovac oil increases the power output of the panel. • Coating PV panels with a layer of Labovac oil has to be applied in cold countries and not in hot regions. - Abstract: The objective of this research is to develop a new technique for improving the efficiency of Photovoltaic (PV) panels. This technique is done by coating the front surface of the PV panel by a fine layer of oil in order to increase the amount of light transmitted to the panel, and consequently its efficiency. Different types of oils are examined, including both mineral oils and natural oils. In case of mineral oils; vacuum pump oil (Labovac oil), engine oil (Mobil oil) and brake oil (Abro oil) are examined, while in case of natural oils; olive and sunflower oils are examined. An experimental setup has been developed to examine the performance of the PV panels as a function of oil coatings. The experimental setup consists of an artificial sun, the PV panel under investigation, a cooling system and a measuring system to measure the performance of the panel. It has been found that coating the PV panel with a fine layer of Labovac oil, ∼1 mm thick, improves the efficiency of the PV panel by more than 20%, and this is due to the high transmissivity of the Labovac oil compared to other oils. However, the Labovac oil has a drawback which is overheating of the panel due to its high transmissivity. Coating of PV panels with a fine layer of Labovac oil should be done only in cold regions, in order to avoid the heating effect that can decrease the power output of PV panels.

Hydrodynamic analysis application of contaminated groundwater remediation to oil hydrocarbons

OpenAIRE

Pajić Predrag R.; Čalenić Aleksandar I.; Polomčić Dušan M.; Bajić Dragoljub I.

2017-01-01

In this paper, the application of the hydrodynamic analysis in the selected ‘pumping and treatment’ remediation method of groundwater hydrocarbon pollution in the case of the Pancevo oil refinery is examined. The applied hydrodynamic analysis represents a regular and necessary approach in modern hydrogeology. Previous chemical analysis of soil and groundwater samples at observation objects revealed their pollution by oil products. New researches included the constraction of 12 piezometric bor...

How crude oil consumption impacts on economic growth of Sub-Saharan Africa?

International Nuclear Information System (INIS)

Bashiri Behmiri, Niaz; Pires Manso, José R.

2013-01-01

This study investigates the causality relationship between crude oil consumption and economic growth in twenty three Sub-Saharan African countries. We applied a multivariate panel Granger causality framework during 1985–2011 and we included crude oil price as the control variable of the model. The results indicate that in the short-run, there is a bi-directional causality relationship between crude oil consumption and economic growth in oil importing region and there is a uni-directional causality relationship from crude oil consumption to GDP in oil exporting region. However, in the long-run there is a bi-directional causality relationship between them in both regions. Therefore, reducing crude oil consumption without employing appropriate policies adversely impacts on economic growth of Sub-Saharan Africa. Hence, in order to reduce crude oil dependency of the region policymakers should pay more attention to the issue of energy efficiency programs. - Highlights: ► We examined Granger causality among oil consumption and GDP in Sub-Saharan Africa. ► Crude oil price is the control variable of the model. ► There is short run bi-directional causality among oil and GDP (oil importing). ► There is short run uni-directional causality from oil to GDP (oil exporting). ► There is a long run bi-directional causality among oil and GDP in both regions

40 CFR 80.513 - What provisions apply to transmix processing facilities?

Science.gov (United States)

2010-07-01

... processing. This section applies to refineries that produce diesel fuel from transmix by distillation or other refining processes but do not produce diesel fuel by processing crude oil. This section only...

Effect of oil palm sludge on cowpea nodulation and weed control in ...

African Journals Online (AJOL)

A field trial was conducted at the Rivers State University of Science and Technology Research and Training farm Port Harcourt to test the effect of oil palm sludge on cowpea nodulation and weed control. The cultivars of cowpea used were Dan Kano, Bornu local and Sokoto local while the oil palm sludge levels applied ...

Determination of Minimum Miscibility Pressure in supercritical extractor using oil saturated sample

DEFF Research Database (Denmark)

Rudyk, Svetlana Nikolayevna; Søgaard, Erik Gydesen; Abbasi, Waqas A.

2009-01-01

with a given oil reservoir at the reservoir temperature. The oil formation to which the process is applied must be operated at or above the MMP. Before field trial this parameter is to be determined at the laboratory which traditionally is done by help of a slim tube or a raising bubble experiments. However...

Plant Oils as Potential Sources of Vitamin D

Directory of Open Access Journals (Sweden)

Gabriele I Stangl

2016-08-01

Full Text Available To combat vitamin D insufficiency in a population, reliable diet sources of vitamin D are required. The recommendations to consume more oily fish and the use of UVB treated yeast are already applied strategies to address vitamin D insufficiency. This study aimed to elucidate the suitability of plant oils as an alternative vitamin D source. Therefore, plant oils that are commonly used in human nutrition were firstly analyzed for their content of vitamin D precursors and metabolites. Secondly, selected oils were exposed to a short-term UVB irradiation to stimulate the synthesis of vitamin D. Finally, to elucidate the efficacy of plant-derived vitamin D to improve the vitamin D status, we fed UVB-exposed wheat germ oil for 4 weeks to mice and compared them with mice that received non-exposed or vitamin D3 supplemented wheat germ oil. Sterol analysis revealed that the selected plant oils contained high amounts of ergosterol, but also 7-dehydrocholesterol (7-DHC, with the highest concentrations found in wheat germ oil. Exposure to UVB irradiation resulted in a partial conversion of ergosterol and 7-DHC to vitamin D2 and D3 in these oils. Mice fed the UVB-exposed wheat germ oil were able to improve their vitamin D status as shown by the rise in the plasma concentration of 25 hydroxyvitamin D (25(OHD and the liver content of vitamin D compared to mice fed the non-exposed oil. However, the plasma concentration of 25(OHD of mice fed the UVB-treated oil did not reach the values observed in the group fed the D3 supplemented oil. It was striking that the intake of the UVB-exposed oil resulted in distinct accumulation of vitamin D2 in the livers of these mice. In conclusion, plant oils, in particular wheat germ oil, contain considerable amounts of vitamin D precursors which can be converted to vitamin D via UVB exposure. However, the UVB-exposed wheat germ oil was less effective to improve the 25(OHD plasma concentration than a supplementation with vitamin D

Cyber Physical Intelligence for Oil Spills (CPI)

Science.gov (United States)

Lary, D. J.

2015-12-01

The National Academy of Sciences estimate 1.7 to 8.8 million tons of oil are released into global waters every year. The effects of these spills include dead wildlife, oil covered marshlands and contaminated water. Deepwater horizon cost approximately $50 billion and severely challenged response capabilities. In such large spills optimizing a coordinated response is a particular challenge. This challenge can be met in a revolutionary new way by using an objectively optimized Cyber Physical Decision Making System (CPS) for rapid response products and a framework for objectively optimized decision-making in an uncertain environment. The CPS utilizes machine learning for the processing of the massive real-time streams of Big Data from comprehensive hyperspectral remote sensing acquired by a team of low-cost robotic aerial vehicles, providing a real-time aerial view and stream of hyperspectral imagery from the near UV to the thermal infrared, and a characterization of oil thickness, oil type and oil weathering. The objective decision making paradigm is modeled on the human brain and provides the optimal course trajectory for response vessels to achieve the most expeditious cleanup of oil spills using the available resources. In addition, oil spill cleanups often involve surface oil burns that can lead to air quality issues. The aerial vehicles comprehensively characterize air quality in real-time, streaming location, temperature, pressure, humidity, the abundance of 6 criterion pollutants (O3, CO, NO, NO2, SO2, and H2S) and the full size distribution of airborne particulates. This CPS can be readily applied to other systems in agriculture, water conversation, monitoring of stream quality, air quality, diagnosing risk of wild fires, etc..

Visible and near-infrared spectral signatures for adulteration assessment of extra virgin olive oil

Science.gov (United States)

Mignani, A. G.; Ciaccheri, L.; Ottevaere, H.; Thienpont, H.; Conte, L.; Marega, M.; Cichelli, A.; Attilio, C.; Cimato, A.

2010-04-01

Because of its high price, the extra virgin olive oil is frequently target for adulteration with lower quality oils. This paper presents an innovative optical technique capable of quantifying the adulteration of extra virgin olive oil caused by lowergrade olive oils. It relies on spectral fingerprinting the test liquid by means of diffuse-light absorption spectroscopy carried out by optical fiber technology in the wide 400-1700 nm spectral range. Then, a smart multivariate processing of spectroscopic data is applied for immediate prediction of adulterant concentration.

Oil/gas collector/separator for underwater oil leaks

Energy Technology Data Exchange (ETDEWEB)

Henning, C.D.

1992-12-31

This invention is comprised of an oil/gas collector/separator for recovery of oil leaking, for example, from an offshore or underwater oil well. The separator is floated over the point of the leak and tethered in place so as to receive oil/gas floating, or forced under pressure, toward the water surface from either a broken or leaking oil well casing, line, or sunken ship. The separator is provided with a downwardly extending skirt to contain the oil/gas which floats or is forced upward into a dome wherein the gas is separated from the oil/water, with the gas being flared (burned) at the top of the dome, and the oil is separated from water and pumped to a point of use. Since the density of oil is less than that of water it can be easily separated from any water entering the dome.

Mining for oil in Japan. Report No. 89. [Higashiyama

Energy Technology Data Exchange (ETDEWEB)

1947-09-03

Mining for petroleum by underground methods was undertaken in 1940 by the Japanese in the Higashiyama oil field, Niigata Prefecture, as a means of obtaining additional oil from the sands unrecoverable by wells from the surface. The oil is obtained by gravitational drainage through mine openings and is transported through a gathering system, collected in a sump at the bottom of the main shaft and pumped to the surface. Total production of crude oil for the first six years of operation of the Higashiyama mine was 24,914 kiloliters (156,710 barrels). Average production per meter of gallery for the period 1941-46 was 2.69 kiloliters, equivalent to five barrels per foot. Operations were undertaken without careful studies of the residual oil content of the reservoir sands, or a correct understanding of the producing possibilities of the property. Recoveries leave much to be desired for profitable operation. The results achieved, however, appear to have been successful in view of limited natural oil resources and the great need for petroleum products. The work accomplished in pioneering oil-mining in Japan has provided a background of valuable knowledge and experience which will be beneficial in carrying out future mining projects. Other shallow fields, such as Niitsu, Hibiki, and the Takeishi structure present possibilities of applying underground mining methods to recover additional oil.

Biorremediation of soil polluted by 75000 ppm of waste motor oil applying biostimulation and phytoremediation with Sorghum vulgare and Bacillus cereus or Burkholderia cepacia

Directory of Open Access Journals (Sweden)

Balderas-León Iván

2015-02-01

Full Text Available Waste motor oil (WMO pollutes soil and causing lost soil fertility. An alternative to solve this problem its bioremediation (BR by double and following biostimulation (BS with mineral solution (MS and a legume as green manure (GM then using phytoremediation (PR with growth promoting vegetal bacteria (GPVB like Bacillus cereus and Burkholderia cepacia to minimize remaining WMO. The aims of this research were: a bioremediation of polluted soil by 75000 ppm of WMO by biostimulation and then b Its phytoremediation for remaining WMO by Sorghum vulgare inoculated with B. cereus and B. cepacia. Soil polluted by high concentration WMO was biostimulated with MS, and then Phaseolus vulgaris treated by GPVB was incorporated as GM, finally to apply PR to eliminate WMO with S. vulgare with GPVB. Results indicate that soil bioremediated by biostimulation with MS, WMO decreased at 32500 ppm/30 days, and then with GM, WMO was reduced at 10100 ppm after/90 days. Finally, to apply phytoremediation using S. vulgare and GPVB at flowering, WMO was reduced from 2500 ppm to 800 ppm. For recovering soil impacted by high concentration WMO to apply both techniques double and following BS and PR are the best option than each technique separately.

27 CFR 21.98 - Bone oil (Dipple's oil).

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Bone oil (Dipple's oil....98 Bone oil (Dipple's oil). (a) Color. The color shall be a deep brown. (b) Distillation range. When... below 90 °C. (c) Pyrrol reaction. Prepare a 1.0 percent solution of bone oil in 95 percent alcohol...

Rapid methodology via mass spectrometry to quantify addition of soybean oil in extra virgin olive oil: A comparison with traditional methods adopted by food industry to identify fraud.

Science.gov (United States)

da Silveira, Roberta; Vágula, Julianna Matias; de Lima Figueiredo, Ingrid; Claus, Thiago; Galuch, Marilia Bellanda; Santos Junior, Oscar Oliveira; Visentainer, Jesui Vergilio

2017-12-01

Fast and innovative methodology to monitors the addition of soybean oil in extra virgin olive oil was developed employing ESI-MS with ionization operating in positive mode. A certified extra virgin olive oil and refined soybean oil samples were analyzed by direct infusion, the identification of a natural lipid marker present only in soybean oil (m/z 886.68 [TAG+NH 4 ] + ) was possible. The certified extra virgin olive oil was purposely adulterated with soybean oil in different levels (1, 5, 10, 20, 50, 70, 90%) being possible to observe that the new methodology is able to detect even small fraud concentration, such as 1% (v/v). Additionally, commercial samples were analyzed and were observed the addition of soybean oil as a common fraud in this segment. This powerful analytical method proposed could be applied as routine analysis by control organization, as well as food industries, considering its pronounced advantages; simplicity, rapidity, elevated detectability and minor amounts of sample and solvent consumed. Copyright © 2017 Elsevier Ltd. All rights reserved.

The application of vacuum redistillation of patchouli oil to improve patchouli alcohol compound

Science.gov (United States)

Asnawi, T. M.; Alam, P. N.; Husin, H.; Zaki, M.

2018-04-01

Patchouli oil produced by traditional distillation of patchouli leaves and stems by farmers in Aceh still has low patchouli alcohol compound. In order to increase patchouli alcohol concentration, vacuum redistillation process using packed column was introduced. This research was conducted to fractionate terpene (alpha-copinene) from oxygenated hydrocarbon (patchouli alcohol) compound. The operation condition was conducted at two variables that was dependent variable and independent variable. The dependent variable was the 30 cm height distillation packed column, by using raschig ring with 8 mm x 8 mm dimension. And the independent variable was operating temperature 130 °C and 140 °C., vacuum pressure 143,61 mbar, 121,60 mbar and 88,59 mbar and operation time 2 hours, 3 hours and 5 hours. Total of treatments applied in this works were 3 x 3 x 3 or equal to 27 treatments. Patchouli oil used in this research was obtained from Desa Teladan-Lembah Seulawah, Aceh Province. The initial patchouli alcohol compound which analyzed with GC-MS contained 16,02% before treatment applied. After vacuum redistillation process treatment applied patchouli oil concentration increase up to 34,67%. Physico-chemical test of patchouli oil after vacuum redistillation is in accordance with SNI 06-23852006 standard.

Assessing alternative options for allocating oil revenue in Iran

International Nuclear Information System (INIS)

Barkhordar, Zahra A.; Saboohi, Yadollah

2013-01-01

The present paper focuses on medium-term effects of alternative windfall management strategies for a resource abundant country where the resource revenues are expected to last over a prolonged period. In particular, the trade-off between spending and saving is analyzed within the framework of a recursive dynamic computable general equilibrium model. The model is further validated against historical data available for 2001–2010. The total factor productivity is calculated endogenously in the model based on a function that reflects the changes in factor productivity. The results suggest that saving oil revenues, whether in an oil fund or through physical investment in domestic sectors, leads to a higher economic growth. However, physical investment is superior in the short to medium term based on the resultant GDP while creating an oil fund might be more beneficial in the post oil era. - Highlights: • A recursive dynamic general equilibrium model is applied for Iran. • The total factor productivity is calculated endogenously. • Alternative revenue allocation options are investigated. • Physical investment of oil windfalls leads to higher economic growth in medium run. • Financial investment of oil revenues leads to higher economic growth in long run

Centennial review-forecast--oil sands, shales spar for markets

Energy Technology Data Exchange (ETDEWEB)

Pamenter, C B

1967-09-01

The relationship between possible developments of tar sands and oil shale deposits to the future of the oil and gas industry is examined. The Athabasca tar sands are estimated to contain 85 billion bbl of synthetic crude oil which can be exploited using currently available mining equipment and proven techniques. Another 240 billion bbl of synthetic crude are potentially available through in-situ extraction methods. Great Canadian Oil Sands Ltd. is using an extraction procedure which involves a surface mining operation, extraction and processing of the bitumen, and product shipments via a 266-mile pipeline. This procedure will be used to produce 45,000 bpd of synthetic crude and 300 ton per day of sulfur. Syncrude Canada Ltd. and Shell Canada Ltd. both have applied to the Alberta government for permission to operate 100,000-bpd operations. Syncrudes is a mining operation and Shell plans to use in-situ extraction. A number of companies have conducted research projects concerning shale oil recovery. The majority of these projects have been aimed at improving mining operations. In-situ retorting of kerogen and extraction of oil has also received consideration.

The US Shale Gas Revolution and Its Externality on Crude Oil Prices: A Counterfactual Analysis

Directory of Open Access Journals (Sweden)

Hongxun Liu

2018-03-01

Full Text Available The expansion of shale gas production since the mid-2000s which is commonly referred to as “shale gas revolution” has had large impacts on global energy outlook. The impact is particularly substantial when it comes to the oil market because natural gas and oil are substitutes in consumption and complements and rivals in production. This paper investigates the price externality of shale gas revolution on crude oil. Applying a structural vector autoregressive model (VAR model, the effect of natural gas production on real oil price is identified in particular, and then based on the identification, counterfactuals of oil price without shale gas revolution are constructed. We find that after the expansion of shale gas production, the real West Texas Intermediate (WTI oil price is depressed by 10.22 USD/barrel on average from 2007 to 2017, and the magnitude seems to increase with time. In addition, the period before shale gas revolution is used as a “thought experiment” for placebo study. The results support the hypothesis that real WTI oil price can be reasonably reproduced by our models, and the estimated gap for oil price during 2007–2017 can be attributed to shale gas revolution. The methodology and framework can be applied to evaluate the economic impacts of other programs or policies.

Evolution of oil/water interface in the presence of SDBS detected by dual polarization interferometry

Science.gov (United States)

Duan, Ming; Ding, Ziling; Wang, Hu; Xiong, Yan; Fang, Shenwen; Shi, Peng; Liu, Shuai

2018-01-01

In this work, the technique of dual polarization interferometry (DPI) was applied to establish a new method to monitor the real-time evolution of oil/water interface in the presence of sodium dodecyl benzene sulfonate (SDBS) at molecular level. A three-stage model of adsorption-desorption-detachment had been proposed and was systematically discussed upon the addition of different SDBS concentrations based on the variation of the interfacial mass with time. The results demonstrated two patterns of adsorption morphology at the oil/water interface, SDBS mono-molecules and SDBS hemi-micelles at SDBS concentrations below and above cmc respectively according to the relaxation time obtained by theoretical model and the reaction order calculated by integral method in the analysis of adsorbed dynamics. The capability of oil detachment with the aid of SDBS as well as the properties of the outlet fluid were investigated under two patterns of adsorption morphologies, which showed different effects of oil detachment with the aid of SDBS molecules. The speed of oil detachment and the fluorescence intensity of the outlet fluid during the detachment process indicated the fact that the oil detachment capability was significantly promoted by the morphology of the absorbed hemi-micelles. The findings in the present study are crucial for fully understanding the interfacial behavior of surfactants applied in oil/water interface, which is of great significance in enhanced oil recovery and pollution industry.

Global Integration, Non-Oil Export and Economic Growth in Nigeria

Directory of Open Access Journals (Sweden)

Ozoemena Stanley Nwodo

2017-03-01

Full Text Available This study focuses on global integration, non-oil export and economic growth in Nigeria. The direct and interaction effect of the both openness variables and non-oil export on economic growth in Nigeria is investigated using quarterly data from 1986-2014. For analysis, it uses one measures of financial openness: de facto (total capital flow variables following Aizenman and Noy (2009.and a measure of trade openness adopted by Okoh (2004. The study applies the Autoregressive Distributed Lag Model (ARDL. The results show positive impact of non-oil export on economic growth in Nigeria both in the short run and in the long run, negative effect of trade and financial openness on economic growth however, the result recorded a negative effect of the interaction of trade openness and non-oil export on economic growth and a positive effect of the interaction of financial openness and non-oil export on economic growth. Thus, the study recommends among others that government should get the fundamentals right in the economy first that will boost non-oil sector before opening the economy for trade.

Development of a statistical oil spill model for risk assessment.

Science.gov (United States)

Guo, Weijun

2017-11-01

To gain a better understanding of the impacts from potential risk sources, we developed an oil spill model using probabilistic method, which simulates numerous oil spill trajectories under varying environmental conditions. The statistical results were quantified from hypothetical oil spills under multiple scenarios, including area affected probability, mean oil slick thickness, and duration of water surface exposed to floating oil. The three sub-indices together with marine area vulnerability are merged to compute the composite index, characterizing the spatial distribution of risk degree. Integral of the index can be used to identify the overall risk from an emission source. The developed model has been successfully applied in comparison to and selection of an appropriate oil port construction location adjacent to a marine protected area for Phoca largha in China. The results highlight the importance of selection of candidates before project construction, since that risk estimation from two adjacent potential sources may turn out to be significantly different regarding hydrodynamic conditions and eco-environmental sensitivity. Copyright © 2017. Published by Elsevier Ltd.

Microbial consortia in mesocosm bioremediation trial using oil sorbents, slow-release fertilizer and bioaugmentation.

Science.gov (United States)

Gertler, Christoph; Gerdts, Gunnar; Timmis, Kenneth N; Golyshin, Peter N

2009-08-01

An experimental prototype oil boom including oil sorbents, slow-release fertilizers and biomass of the marine oil-degrading bacterium, Alcanivorax borkumensis, was applied for sorption and degradation of heavy fuel oil in a 500-L mesocosm experiment. Fingerprinting of DNA and small subunit rRNA samples for microbial activity conducted to study the changes in microbial communities of both the water body and on the oil sorbent surface showed the prevalence of A. borkumensis on the surface of the oil sorbent. Growth of this obligate oil-degrading bacterium on immobilized oil coincided with a 30-fold increase in total respiration. A number of DNA and RNA signatures of aromatic hydrocarbon-degrading bacteria were detected both in samples of water body and on oil sorbent. Ultimately, the heavy fuel oil in this mesocosm study was effectively removed from the water body. This is the first study to successfully investigate the fate of oil-degrading microbial consortia in an experimental prototype for a bioremediation strategy in offshore, coastal or ship-bound oil spill mitigation using a combination of mechanical and biotechnological techniques.

Experimental Study on Breakdown Characteristics of Transformer Oil Influenced by Bubbles

Directory of Open Access Journals (Sweden)

Chunxu Qin

2018-03-01

Full Text Available Bubbles will reduce the electric strength of transformer oil, and even result in the breakdown of the insulation. This paper has studied the breakdown voltages of transformer oil and oil-impregnated pressboard under alternating current (AC and direct current (DC voltages. In this paper, three types of electrodes were applied: cylinder-plan electrodes, sphere-plan electrodes, and cone-plan electrodes, and the breakdown voltages were measured in both no bubbles and bubbles. The sphere-sphere electrodes were used to study the breakdown voltage of the oil-impregnated pressboard. The results showed that under the influence of bubble, the breakdown voltage of the cylinder-plan electrode dropped the most, and the breakdown voltage of the cone-plan electrode dropped the least. The bubbles motion was the key factor of the breakdown. The discharge types of the oil-impregnated pressboard were different with bubbles, and under DC, the main discharge type was flashover along the oil-impregnated pressboard, while under AC, the main discharge type was breakdown through the oil-impregnated pressboard.

A new concept for improved oil spill containment in open waters

International Nuclear Information System (INIS)

Sethness, E.D. Jr.

1990-01-01

In this paper a new concept for improved oil spill containment in open waters is presented. The proposed system is a combination oil boom and wave barrier. Waveguard International has taken its extensive experience as a designer of floating breakwaters and applied this knowledge into the design of a readily transportable, readily deployable floating oil boom with integrated wave attenuation capabilities as well. The new concept is based on the attenuation of the two major natural causes of oil spill dispersion; first, horizontal dispersion caused by wind shear effects; and second, vertical entrainment into the water column caused by the mixing action of wave motion. The physical encirclement of an oil spill with a floating boom to contain horizontal dispersion is not a new concept. Existing systems, however, work best in calm water and rapidly loose efficiency as waves increase. The proposed system can not only physically surround the spill area, but is as much as 90% effective in stopping the transmission of wave energy. The oil boom thus minimizes vertical mixing of the contained oil slick

Strategic environmental assessment applied to the oil and gas planning in Brazil: a proposal; O uso da avaliacao ambiental estrategica no planejamento da oferta de blocos para exploracao e producao de petroleo e gas natural no Brasil: uma proposta

Energy Technology Data Exchange (ETDEWEB)

Teixeira, Izabella Monica Vieira

2008-01-15

This thesis discusses the opportunity to apply strategic environmental assessment (SEA) to the oil and gas planning procedures in Brazil, considering the call for bids' process that has been adopted by the Federal Government since 1999. The thesis presents a literature review on the concepts and principles of environmental assessment, environmental impact assessment and strategic environmental assessment, considering its origins and practice. It also provides an appraisal of the international practice on SEA application to the oil and gas sector planning, as well as and a comparative analysis of the planning system as practiced in Brazil. Based on the international and the national SEA experience, and considering the requirements to address the environmental feasibility of oil and gas offshore activities, a proposal is presented on the framework for the use of the SEA as part of the oil and gas planning process in Brazil, together with the procedural requirements to be met. (author)

Strategic environmental assessment applied to the oil and gas planning in Brazil: a proposal; O uso da avaliacao ambiental estrategica no planejamento da oferta de blocos para exploracao e producao de petroleo e gas natural no Brasil: uma proposta

Energy Technology Data Exchange (ETDEWEB)

Teixeira, Izabella Monica Vieira

2008-01-15

This thesis discusses the opportunity to apply strategic environmental assessment (SEA) to the oil and gas planning procedures in Brazil, considering the call for bids' process that has been adopted by the Federal Government since 1999. The thesis presents a literature review on the concepts and principles of environmental assessment, environmental impact assessment and strategic environmental assessment, considering its origins and practice. It also provides an appraisal of the international practice on SEA application to the oil and gas sector planning, as well as and a comparative analysis of the planning system as practiced in Brazil. Based on the international and the national SEA experience, and considering the requirements to address the environmental feasibility of oil and gas offshore activities, a proposal is presented on the framework for the use of the SEA as part of the oil and gas planning process in Brazil, together with the procedural requirements to be met. (author)

Method for curing alkyd resin compositions by applying ionizing radiation

International Nuclear Information System (INIS)

Watanabe, T.; Murata, K.; Maruyama, T.

1975-01-01

An alkyd resin composition is prepared by dissolving a polymerizable alkyd resin having from 10 to 50 percent of oil length into a vinyl monomer. The polymerizable alkyd resin is obtained by a half-esterification reaction of an acid anhydride having a polymerizable unsaturated group and an alkyd resin modified with conjugated unsaturated oil having at least one reactive hydroxyl group per one molecule. The alkyd resin composition thus obtained is coated on an article, and ionizing radiation is applied on the article to cure the coated film thereon. (U.S.)

Effects of No. 2 fuel oil on hatchability of marine and estuarine bird eggs

Science.gov (United States)

White, Donald H.; King, Kirke A.; Coon, Nancy C.

1979-01-01

Oil spills and discharges may kill birds directly by destroying the insulation that their feathers provide so that they die of exposure; by poisoning them if they ingest oil; and by stressing them so that they starve to death. But oil pollution has more subtle effects, too. Nesting birds exposed to sublethal quantities of oil may transfer the oil to eggs in their nests, thereby causing failure of the eggs to hatch (RITTINGHAUS 1956). Laboratory studies have shown that very small quantities of oil, when applied to eggs of waterfowl, significantly reduced hatchability (HARTUNG 1965, ALBERS 1977a, SZARO and ALBERS 1977). The objective of this study was to determine the effects of external applications of No. 2 fuel oil on embryo survival of naturally and of artificially incubated eggs of marine and estuarine birds.

Compositional modification of crude oil during oil recovery

Energy Technology Data Exchange (ETDEWEB)

Zhu, Yangming; Weng, Huanxin [Department of Earth Sciences, Zhejiang University, Hangzhou 310027 (China); Chen, Zulin; Chen, Qi [Petroleum Geochemistry Research Center, Jianghan Petroleum University, Jingzhou, Hubei (China)

2003-05-01

Ten crude oils from two recovery stages spanning 5-10-year interval of five productive wells in the Tarim Basin, northwest China were analyzed for their compositional modification during production process. Significant compositional changes in polar and nonpolar fractions between the previous oil samples and the latter ones were noted at both bulk and molecular level. The latter oil samples appear to contain more aromatic fraction and less asphaltenes and resin, and their gas chromatography (GC) data for whole oil show reduced alkanes with low molecular weight and enhanced high homologue relative to the previous oil samples. Compared with the oils collected from the previous recovery stage, the concentration of basic type of nitrogen-containing compounds and organic acids in oils from the latter recovery stage have a reducing trend, suggesting the occurrence of interaction between crude oil and reservoir rock.

Anti-wear additive content in fully synthetic PAO and PAG base oils and its effect on electrostatic and tribological phenomena in a rotating shaft-oil-lip seal system

Science.gov (United States)

Gajewski, Juliusz B.; Głogowski, Marek J.

2013-03-01

The paper presents the results of experiments on electrostatic and tribological aspects of different anti-wear additive's contents when an additive is blended with different fully synthetic (poly-α-olefin) and PAG (polyalkylene glycol) base oils in a rotating shaft-oil and oil-lip seal interfacial system. The experimental results are the relationships of electric potential induced in a lip seal's stiffening ring to angular velocity of a rotating metal shaft and to temperature of the oils tested. The braking torque of a shaft is measured with a torquemeter sensor connected directly with a microprocessor-based system for controlling the rotational speed and for measuring the shaft's braking torque and oil temperature. The beneficial and promising results are obtained for PAG when an external DC electric field is applied to the system and the braking torque is then reduced for a certain combination of the base oil and additive's contents. On the basis of the former and present research results an analysis is made to permit one to show how the type of the oils and additives tested can affect both interfaces: rotating shaft-oil and oil-lip of the lip seal and especially the braking torque.

Measurement of quadratic electrogyration effect in castor oil

Science.gov (United States)

Izdebski, Marek; Ledzion, Rafał; Górski, Piotr

2015-07-01

This work presents a detailed analysis of electrogyration measurement in liquids with the usage of an optical polarimetric technique. Theoretical analysis of the optical response to an applied electric field is illustrated by experimental data for castor oil which exhibits natural optical activity, quadratic electro-optic effect and quadratic electrogyration effect. Moreover, the experimental data show that interaction of the oil with a pair of flat electrodes induces a significant dichroism and natural linear birefringence. The combination of these effects occurring at the same time complicates the procedure of measurements. It has been found that a single measurement is insufficient to separate the contribution of the electrogyration effect, but it is possible on the basis of several measurements performed with various orientations of the polarizer and the analyser. The obtained average values of the quadratic electrogyration coefficient β13 in castor oil at room temperature are from - 0.92 ×10-22 to - 1.44 ×10-22m2V-2 depending on the origin of the oil. Although this study is focused on measurements in castor oil, the presented analysis is much more general.

Panorama 2013 - The oil market in 2012 and forward trends

International Nuclear Information System (INIS)

Maisonnier, Guy

2012-11-01

As predicted at the beginning of 2012, the past year has proved fairly similar to 2011, focused more on geopolitical risk than the economic downturn, leading to a high oil price, close to the 2011 price ($110 for Brent). For the future, caution is called for: past performance is no guarantee of future developments... the old saying certainly applies to the oil market. While tension and even runaway oil prices remain a credible scenario for geopolitical reasons, a marked decline in the coming years is also a possibility. Faced with these extreme trends, the market reached an unstable balance at $110 for Brent (WTI around $95). (author)

Comparative Study of Breakdown Voltage of Mineral, Synthetic and Natural Oils and Based Mineral Oil Mixtures under AC and DC Voltages

Directory of Open Access Journals (Sweden)

Abderrahmane Beroual

2017-04-01

Full Text Available This paper deals with a comparative study of AC and DC breakdown voltages of based mineral oil mixtures with natural and synthetic esters mainly used in high voltage power transformers. The goal was to analyze the performances of oil mixtures from the dielectric withstand point of view and to predict the behavior of transformers originally filled with mineral oil and re-filled with synthetic or natural ester oils when emptied for maintenance. The study concerns mixtures based on 20%, 50%, and 80% of natural and synthetic ester oils. AC breakdown voltages were measured using a sphere-sphere electrode system according to IEC 60156 specifications; the same specification was adopted for DC measurements since there is no standard specifications for this voltage waveform. A statistical analysis of the mean values, standard deviations, and histograms of breakdown voltage data was carried out. The Normal and Weibull distribution functions were used to analyze the experimental data and the best function that the data followed was used to estimate the breakdown voltage with risk of 1%, 10%, and 50% probability. It was shown that whatever the applied voltage waveforms, ester oils always have a significantly higher breakdown voltage than mineral oil. The addition of only 20% of natural or synthetic ester oil was sufficient to considerably increase the breakdown voltage of mineral oil. The dielectric strength of such a mixture is much higher than that of mineral oil alone and can reach that of ester oils. From the point of view of dielectric strength, the mixtures constitute an option for improving the performance of mineral oil. Thus, re-filling of transformers containing up to 20% mineral oil residues with ester oils, does not present any problem; it is even advantageous when considering only the breakdown voltage. Under AC, the mixtures with natural ester always follow the behavior of vegetable oil alone. With the exception of the 20% mixture of natural

Organic pollutant removal from edible oil process wastewater using electrocoagulation

Science.gov (United States)

Sharma, S.; Can, O. T.; Hammed, M.; Nawarathna, D.; Simsek, H.

2018-03-01

Wastewaters generated from vegetable oil industries contain a high concentration of organic pollutants that are detrimental to the aquatic ecosystem. Electrochemical processes are gaining importance in the treatment of inorganic and resistant organic pollutants in wastewaters. In this study, electrocoagulation (EC) was applied to remove organic pollutants and oil and grease from canola oil wastewater using aluminum (Al) and iron (Fe) electrodes. The application of EC in the wastewater achieved more than 80% removal of organic carbon and nearly 100% removal of suspended solids (SS). The effectiveness of EC is influenced mainly by current density, pH, electrolyte (NaCl), electrode contact time and electrode type. It was observed that Al electrode combination yielded better removal at a lesser time compared to that of Fe electrodes. However, varying current densities had its significance in terms of coagulation time only. Increase in current density achieved decrease in coagulation time. Both Al and Fe could remove between 52-59% of oil and grease from canola oil wastewater

Determination of Commercials Cooking Oils and Fats Using Chemometrics Methods

International Nuclear Information System (INIS)

Azwan Mat Lazim; Mohd Zuli Jaafar; Phang Wei Shong, P.W.; Suzereen Jamil

2013-01-01

In this study, chemometric method has been used in determining the oil quality. The samples used were olive oil, sunflower oil and butter from two different brands. Two different conditions were applied, either it was fresh or fried. Titratio, a conventional method was used to determine free fatty acids content (FFA), iodine value (IV), and peroxide value (PV). Twelve samples were then used for analysis and their FTIR spectra were measured at 4000-400 cm -1 . The computer stimulation was used to process the data based on their pattern recognition which optimized by principal component analysis (PCA) and partial least squares (PLS). PCA model was used to distinguish the properties between fresh and fried oil. The PLS model was used to predict the value for validation test in comparison with conventional results. Results showed the validation value for fresh oil was 0.90. This indicated the chemometric method was in agreement with conventional method. (author)

Bioinspired Diatomite Membrane with Selective Superwettability for Oil/Water Separation.

Science.gov (United States)

Lo, Yu-Hsiang; Yang, Ching-Yu; Chang, Haw-Kai; Hung, Wei-Chen; Chen, Po-Yu

2017-05-03

Membranes with selective superwettability for oil/water separation have received significant attention during the past decades. Hierarchical structures and surface roughness are believed to improve the oil repellency and the stability of Cassie-Baxter state. Diatoms, unicellular photosynthetic algae, possess sophisticated skeletal shells (called frustules) which are made of hydrated silica. Motivated by the hierarchical micro- and nanoscale features of diatom, we fabricate a hierarchical diatomite membrane which consists of aligned micro-sized channels by the freeze casting process. The fine nano-porous structures of frustules are well preserved after the post sintering process. The bioinspired diatomite membrane performs both underwater superoleophobicity and superhydrophobicity under various oils. Additionally, we demonstrate the highly efficient oil/water separation capabililty of the membranes in various harsh environments. The water flux can be further adjusted by tuning the cooling rates. The eco-friendly and robust bioinspired membranes produced by the simple, cost-effective freeze casting method can be potentially applied for large scale and efficient oil/water separation.

Global volatile profile of virgin olive oils flavoured by aromatic/medicinal plants.

Science.gov (United States)

Perestrelo, R; Silva, C; Silva, P; Câmara, J S

2017-07-15

The global volatile profile of commercial virgin olive oils and flavoured olive oils with aromatic/medicinal plants, was established using liquid-liquid microextraction (LLME) and headspace solid-phase microextraction (HS-SPME) combined with gas chromatography-quadrupole mass spectrometry (GC-qMS). More than 60 volatile organic compounds (VOCs belonging to different groups were identified using both methods. Olive oils volatile profile was slightly influenced by maceration process, which occurred at room temperature (20±2°C) for 15days. The predominant differences were observed in terpenoids group, since some of them were only identified in the flavoured olive oils, while others showed an increase with the maceration process. VOCs mass transfer from plants to olive oils could explain the observed results. Principal components analysis (PCA) applied to LLME/GC-qMS data allowed to distinguish the olive oils. The flavoured oils would increase the use of olive oil among consumers as consequence of the improvement of its aromatic profile and healthy properties. Copyright © 2017 Elsevier Ltd. All rights reserved.

Base Oils Biodegradability Prediction with Data Mining Techniques

Directory of Open Access Journals (Sweden)

Malika Trabelsi

2010-02-01

Full Text Available In this paper, we apply various data mining techniques including continuous numeric and discrete classification prediction models of base oils biodegradability, with emphasis on improving prediction accuracy. The results show that highly biodegradable oils can be better predicted through numeric models. In contrast, classification models did not uncover a similar dichotomy. With the exception of Memory Based Reasoning and Decision Trees, tested classification techniques achieved high classification prediction. However, the technique of Decision Trees helped uncover the most significant predictors. A simple classification rule derived based on this predictor resulted in good classification accuracy. The application of this rule enables efficient classification of base oils into either low or high biodegradability classes with high accuracy. For the latter, a higher precision biodegradability prediction can be obtained using continuous modeling techniques.

Oil and influence: the oil weapon examined

Energy Technology Data Exchange (ETDEWEB)

Maull, H

1975-01-01

The term ''oil weapon'' as used here signifies any manipulation of the price and/or supply of oil by exporting nations with the intention of changing the political behavior of the consumer nations. The political potential of the oil price is fairly restricted so, in effect, the supply interruptions are of prime concern. Manipulating price does, in principle, offer the possibilities of both conferring rewards and inflicting sanctions. Oil could be sold on preferential prices and terms. A precondition for using the oil weapon successfully would be the ability to cause real and serious damage to the consumer countries. Four damaging potentials for using the oil weapon could include its application by: (1) one producer against one consumer; (2) one producer against all consumers; (3) a group of producers against one consumer; and (4) by a group of producers against all consumers. It is concluded that the oil weapon will continue to be a force in the international system. (MCW)

The Middle East: A mixture of oil and politics

International Nuclear Information System (INIS)

Skeet, I.

1991-01-01

The concept of stability is discussed as it applies to the Middle East countries and to the international oil market. The differences in how the various players involved (such as the USA, Europe, Iran, and the Arab countries) view stability are noted. With regard to stability and the oil trade, the results of the recent Gulf war indicate that the international security of oil supply and the regional balance of power in the Gulf are inseparable. Over most of the post-1945 period, there has been a reasonable degree of oil price stability and supply security. This stability and security has not come about through management of the oil price by governments, institutions, or groups of companies. The massive discontinuities in this management process in 1973, 1979/80, and 1986 are brought forward to provide evidence that a new management system must be created to avoid such problems in the future. It is suggested that in the past few years, the management function has been slipping away from OPEC and replaced by a Saudi Arabia/USA joint interest alliance

Oil well spill trough

International Nuclear Information System (INIS)

Wigington, J.R. Sr.

1992-01-01

This patent describes a process involving an oil well and rig having a casing, a platform on the rig extending around the casing. This patent describes improvement in pulling the tubing from the casing; disconnecting joints of tubing thereby; and spilling liquids from the casing, catching spilled liquids from the casing in a basin below the platform, draining the basin substantially simultaneously; connecting the drain hole to a tank, and reducing the pressure in the tank to less than atmospheric pressure. This paper also describes an oil well and rig having a casing; the rig having a platform extending around the casing. This patent describes improvement in a basin surrounding the casing and connected thereto, the basin below the platform, a drain connection in the lower part of the basin, a conduit connected to the drain, and means for applying a suction to the conduit

33 CFR 135.103 - Levy and payment of barrel fee on OCS oil.

Science.gov (United States)

2010-07-01

... SECURITY (CONTINUED) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OFFSHORE OIL POLLUTION COMPENSATION FUND Levy of Fees § 135.103 Levy and payment of barrel fee on OCS oil. (a) A fee of $.03 per... paragraph (a) of this section applies whenever the unobligated Fund balance is less than $200,000,000. (d...

Formation and stability of oil-in-water nanoemulsions containing rice bran oil: in vitro and in vivo assessments

Directory of Open Access Journals (Sweden)

Rocha-Filho Pedro A

2011-09-01

Full Text Available Abstract Background Nanoemulsions have practical application in a multitude of commercial areas, such as the chemical, pharmaceutical and cosmetic industries. Cosmetic industries use rice bran oil in sunscreen formulations, anti ageing products and in treatments for skin diseases. The aim of this study was to create rice bran oil nanoemulsions using low energy emulsification methods and to evaluate their physical stability, irritation potential and moisturising activity on volunteers with normal and diseased skin types. Results The nanoemulsion developed by this phase diagram method was composed of 10% rice bran oil, 10% surfactants sorbitan oleate/PEG-30 castor oil, 0.05% antioxidant and 0.50% preservatives formulated in distilled water. The nanoemulsion was stable over the time course of this study. In vitro assays showed that this formulation has a low irritation potential, and when applied to human skin during in vivo studies, the nanoemulsion improved the skin's moisture and maintained normal skin pH values. Conclusion The results of irritation potential studies and in vivo assessments indicate that this nanoemulsion has potential to be a useful tool to treat skin diseases, such as atopic dermatitis and psoriasis.

Biochemically enhanced oil recovery and oil treatment

Science.gov (United States)

Premuzic, Eugene T.; Lin, Mow

1994-01-01

This invention relates to the preparation of new, modified organisms, through challenge growth processes, that are viable in the extreme temperature, pressure and pH conditions and salt concentrations of an oil reservoir and that are suitable for use in microbial enhanced oil recovery. The modified microorganisms of the present invention are used to enhance oil recovery and remove sulfur compounds and metals from the crude oil.

Steam producing plant concept of 4S for oil sand extraction

International Nuclear Information System (INIS)

Matsuyama, Shinichiro; Nishiguchi, Youhei; Sakashita, Yoshiaki; Kasuga, Shoji; Kawashima, Masatoshi

2009-01-01

Plant concept of small fast reactor '4S' applying to continuous steam production for recovery of crude oil from oil sands was investigated. Assuming typical steam assisted gravity drainage (SAGD) plant whose production scale is 120,000 barrels per day of a crude oil, concept of nuclear steam supply system consisting of eight reactor modules for steam production and three reactor modules for electric generation of the 4S with a thermal rating of 135 MWt was established without any essential or significant design change from the preceding 4S with a thermal rating of 30 MWt. The 4S, provided for an oil sand extraction, will reduce greenhouse gas emission significantly, and has not much burden for development and licensing and has economic competitiveness. (author)

High-throughput authentication of edible oils with benchtop Ultrafast 2D NMR.

Science.gov (United States)

Gouilleux, B; Marchand, J; Charrier, B; Remaud, G S; Giraudeau, P

2018-04-01

We report the use of an Ultrafast 2D NMR approach applied on a benchtop NMR system (43 MHz) for the authentication of edible oils. Our results demonstrate that a profiling strategy based on fast 2D NMR spectra recorded in 2.4 min is more efficient than the standard 1D experiments to classify oils from different botanical origins, since 1D spectra on the same samples suffer from strong peak overlaps. Six edible oils with different botanical origins (olive, hazelnut, sesame, rapeseed, corn and sunflower) have been clearly discriminated by PCA analysis. Furthermore, we show how this approach combined with a PLS model can detect adulteration processes such as the addition of hazelnut oil into olive oil, a common fraud in food industry. Copyright © 2017 Elsevier Ltd. All rights reserved.