WorldWideScience

Sample records for stable temperature profile

  1. Temperature profile detector

    Science.gov (United States)

    Tokarz, Richard D.

    1983-01-01

    Temperature profiles at elevated temperature conditions are monitored by use of an elongated device having two conductors spaced by the minimum distance required to normally maintain an open circuit between them. The melting point of one conductor is selected at the elevated temperature being detected, while the melting point of the other is higher. As the preselected temperature is reached, liquid metal will flow between the conductors, creating short circuits which are detectable as to location.

  2. Temperature-profile detector

    Science.gov (United States)

    Not Available

    1981-01-29

    Temperature profiles at elevated temperature conditions are monitored by use of an elongated device having two conductors spaced by the minimum distance required to normally maintain an open circuit between them. The melting point of one conductor is selected at the elevated temperature being detected, while the melting point of the other is higher. As the preselected temperature is reached, liquid metal will flow between the conductors creating short circuits which are detectable as to location.

  3. On bifurcations of temperature profiles

    International Nuclear Information System (INIS)

    Bachmann, P.; Suender, D.; Wobig, H.

    1998-01-01

    Multiple stationary solutions of the one-dimensional heat conduction equation and bifurcation phenomena are known to be caused by the non-monotonic dependence of the impurity radiation function on the temperature, and the non-linearity of the heat flux in the high-recycling regime in front of the divertor target plates. In this paper we report on bifurcation and time evolution of temperature profiles along the magnetic field lines between two target plates owing to localized heat sources and energy loss due to the radiation of different impurities which are described by simple model functions. The main result is that depending on the number of different impurity species and their densities there may exist multiple stationary profiles. A linear stability analysis of stationary temperature profiles leads to a Schroedinger-type equation for the temperature perturbation. Then the fully time-dependent problem is solved. For the case of two different impurity species there is a maximum of seven steady temperature profiles with four of them proved to be stable. (orig.)

  4. A temperature profiler

    Digital Repository Service at National Institute of Oceanography (India)

    Peshwe, V.B.; Desa, E.

    An instrument developed for measuring temperature profiles at sea in depth or time scales is described. PC-based programming offers flexibility in setting up the instrument for the mode of operation prior to each cast. A real time clock built...

  5. Temperature and Humidity Control in Livestock Stables

    DEFF Research Database (Denmark)

    Hansen, Michael; Andersen, Palle; Nielsen, Kirsten M.

    2010-01-01

    The paper describes temperature and humidity control of a livestock stable. It is important to have a correct air flow pattern in the livestock stable in order to achieve proper temperature and humidity control as well as to avoid draught. In the investigated livestock stable the air flow...... is controlled using wall mounted ventilation flaps. In the paper an algorithm for air flow control is presented meeting the needs for temperature and humidity while taking the air flow pattern in consideration. To obtain simple and realisable controllers a model based control design method is applied....... In the design dynamic models for temperature and humidity are very important elements and effort is put into deriving and testing the models. It turns out that non-linearities are dominating in both models making feedback linearization the natural design method. The air controller as well as the temperature...

  6. Influence of stability on the flux-profile relationships for wind speed, Φm, and temperature, Φh, for the stable atmospheric boundary layer

    Directory of Open Access Journals (Sweden)

    C. Yagüe

    2006-01-01

    Full Text Available Data from SABLES98 experimental campaign have been used in order to study the influence of stability (from weak to strong stratification on the flux-profile relationships for momentum, Φm, and heat, Φh. Measurements from 14 thermocouples and 3 sonic anemometers at three levels (5.8, 13.5 and 32 m for the period from 10 to 28 September 1998 were analysed using the framework of the local-scaling approach (Nieuwstadt, 1984a; 1984b, which can be interpreted as an extension of the Monin-Obukhov similarity theory (Obukhov, 1946. The results show increasing values of Φm and Φh with increasing stability parameter ζ=z/Λ, up to a value of ζ≈1–2, above which the values remain constant. As a consequence of this levelling off in Φm and Φh for strong stability, the turbulent mixing is underestimated when linear similarity functions (Businger et al., 1971 are used to calculate surface fluxes of momentum and heat. On the other hand when Φm and Φh are related to the gradient Richardson number, Ri, a different behaviour is found, which could indicate that the transfer of momentum is greater than that of heat for high Ri. The range of validity of these linear functions is discussed in terms of the physical aspects of turbulent intermittent mixing.

  7. Ion temperature profiles in JET

    International Nuclear Information System (INIS)

    Hellermann, M. von; Mandl, W.; Summers, H.P.; Weisen, H.

    1989-01-01

    The results presented in this paper have shown some extreme cases of ion temperature profiles illustrating the different operation modes of the JET tokamak. In the three examples of low-density high temperature, high-density moderates and high-density high-confinement plasmas comparable values of a maximum fusion product n d T i τ E in the order of 10 20 keV m -3 sec are achieved. (author) 1 ref., 7 figs

  8. Temperature Profile of the Duracell Test Strip.

    Science.gov (United States)

    Viiri, Jouni; Kettunen, Lasse

    1996-01-01

    Presents the temperature profile of the Duracell Test Strip obtained using a Inframetrics 740 thermal imaging radiometer and ThermaGRAM95 software and compares this to the theoretical profile derived by Clark and Bonicamp. (JRH)

  9. The temperature profile in a forest

    Science.gov (United States)

    H.A. Fowells

    1948-01-01

    The temperature profile of a mature forest seldom has been observed. Temperatures at specific locations are of interest to the forester because they may help explain many phenomena, such as growth or death of seedlings and freezing of terminals and floral parts of trees. The opportunity to combine a vertical succession of such temperature measurements into a...

  10. Raman Lidar Temperature Profiler Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Aircraft wake vortices is especially hazardous during the landing and taking-off phases of flight. It is essential to obtain an accurate atmospheric temperature...

  11. Temperature profiles in the Harwell boreholes

    International Nuclear Information System (INIS)

    Robins, N.S.

    1983-03-01

    Heat flow at Harwell is estimated at 45 mWm -2 (milli Watt per metre squared is the unit of heat flow). Thermal conductivity values for the formations penetrated range from 1.0 to 4.6 Wm -1 K -1 . The temperature profiles recorded in the boreholes enable the vertical groundwater flow patterns within two poorly permeable mudrock units to be evaluated. The two mudrock units act as leaky barriers each separating a pair of aquifer units which induce a vertical hydraulic gradient across the mudrocks. The flow velocity results for the upper mudrock units derived from the temperature profile are compatible with values for groundwater potential derived from hydraulic data (10 -9 ms -1 from the temperature profile and 10 -12 ms -1 from the hydraulic observations). The results from the lower mudrock sequence are incompatible and this may be due to some other overiding influence upon the temperature profile. (author)

  12. Profile shape parameterization of JET electron temperature and density profiles

    International Nuclear Information System (INIS)

    Schunke, B.

    1997-01-01

    The temperature and density profiles of the Joint European Torus (JET) are parametrized using log additive models in the control variables. Predictive error criteria are used to determine which terms in the log linear model to include. The density and temperature profiles are normalized to their line averages (n-bar and T-bar). The normalized ohmic density shape depends primarily on the parameter n-bar/B t , where B t is the toroidal magnetic field. Both the low mode (L mode) and the edge localized mode-free (ELM-free) high mode (H mode) temperature profiles shapes depend strongly on the type of heating power, with ion cyclotron resonant heating (ICRH) producing a more peaked profile than neutral beam injection (NBI). Given the heating type dependence, the L mode temperature shape is nearly independent of the other control variables. The H mode temperature shape broadens as the effective charge, Z eff , increases. The line average L mode temperature scales as B 0.96 t (power per particle) 0.385 . The L mode normalized density shape depends primarily on the ratio of line average density, n-bar, to the edge safety factor, q 95 . As n-bar/q 95 increases, the profile shape broadens. The current, I p , is the most important control variable for the normalized H mode density. As the current increases, the profile broadens and the gradient at the edge sharpens. Increasing the heating power, especially ICRH, or decreasing the average density, peaks the H mode density profile slightly. (author). 15 refs, 12 figs, 10 tabs

  13. Parametric dependencies of JET electron temperature profiles

    Energy Technology Data Exchange (ETDEWEB)

    Schunke, B. [Commission of the European Communities, Abingdon (United Kingdom). JET Joint Undertaking; Imre, K.; Riedel, K. [New York Univ., NY (United States)

    1994-07-01

    The JET Ohmic, L-Mode and H-Mode electron temperature profiles obtained from the LIDAR Thomson Scattering Diagnostic are parameterized in terms of the normalized flux parameter and a set of the engineering parameters like plasma current, toroidal field, line averages electron density... It is shown that the electron temperature profiles fit a log-additive model well. It is intended to use the same model to predict the profile shape for D-T discharges in JET and in ITER. 2 refs., 5 figs.

  14. BOREAS AFM-06 Mean Temperature Profile Data

    Science.gov (United States)

    Wilczak, James; Hall, Forrest G. (Editor); Newcomer, Jeffrey A. (Editor); Smith, David E. (Technical Monitor)

    2000-01-01

    The Boreal Ecosystem-Atmosphere Study (BOREAS) Airborne Fluxes and Meteorology (AFM)-6 team from the National Oceanic and Atmospheric Adminsitration/Environment Technology Laboratory (NOAA/ETL) operated a 915-MHz wind/Radio Acoustic Sounding System (RASS) profiler system in the Southern Study Area (SSA) near the Old Jack Pine (OJP) tower from 21 May 1994 to 20 Sep 1994. The data set provides temperature profiles at 15 heights, containing the variables of virtual temperature, vertical velocity, the speed of sound, and w-bar. The data are stored in tabular ASCII files. The mean temperature profile data are available from the Earth Observing System Data and Information System (EOSDIS) Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC). The data files are available on a CD-ROM (see document number 20010000884).

  15. Temperature-amplitude coupling for stable biological rhythms at different temperatures.

    Science.gov (United States)

    Kurosawa, Gen; Fujioka, Atsuko; Koinuma, Satoshi; Mochizuki, Atsushi; Shigeyoshi, Yasufumi

    2017-06-01

    Most biological processes accelerate with temperature, for example cell division. In contrast, the circadian rhythm period is robust to temperature fluctuation, termed temperature compensation. Temperature compensation is peculiar because a system-level property (i.e., the circadian period) is stable under varying temperature while individual components of the system (i.e., biochemical reactions) are usually temperature-sensitive. To understand the mechanism for period stability, we measured the time series of circadian clock transcripts in cultured C6 glioma cells. The amplitudes of Cry1 and Dbp circadian expression increased significantly with temperature. In contrast, other clock transcripts demonstrated no significant change in amplitude. To understand these experimental results, we analyzed mathematical models with different network topologies. It was found that the geometric mean amplitude of gene expression must increase to maintain a stable period with increasing temperatures and reaction speeds for all models studied. To investigate the generality of this temperature-amplitude coupling mechanism for period stability, we revisited data on the yeast metabolic cycle (YMC) period, which is also stable under temperature variation. We confirmed that the YMC amplitude increased at higher temperatures, suggesting temperature-amplitude coupling as a common mechanism shared by circadian and 4 h-metabolic rhythms.

  16. A stable boundary layer perspective on global temperature trends

    International Nuclear Information System (INIS)

    McNider, R T; Christy, J R; Biazar, A

    2010-01-01

    temperatures in the stable boundary layer are not very robust measures of the heat content in the deep atmosphere and climate models do not predict minimum temperatures well, minimum temperatures should not be used as a surrogate for measures of deep atmosphere global warming.

  17. TEMPERATURE PROFILES IN A PROPELLANT TANK

    Science.gov (United States)

    Danilowicz, R. L.

    1994-01-01

    A computer program has been developed which analyzes by means of mathematical models the temperature profiles in the contents of a filled propellant tank. In designing space vehicles using cryogenic liquid propellants, it is necessary to know how heat transferred from the tank walls and heat absorbed internally affect the temperature distribution with the tank contents. The mathematical flow model is based on results from small-scale experiments. The results showed that when a subcooled fluid is subject to both nonuniform internal heating and wall heating, two distinct temperature regions are developed. In the lower region, the fluid is thoroughly mixed and maintains a uniform temperature profile. In the upper region, a stratified layer develops, and a temperature gradient is formed from the accumulation of warm fluid from the boundary layer along the tank walls; it also indicated that the temperature profiles in the stratified layer exhibited similarity. This concept was developed primarily for internal heating caused by nuclear radiation. However, the theory and computer program are applicable for any form of internal or bulk heating. This program is written in FORTRAN IV for batch execution and has been implemented on the IBM 7094. This program was developed in 1970.

  18. Temperature profiling in the atmosphere using lidars

    Science.gov (United States)

    Arshinov, Yuri; Bobrovnikov, Sergey M.; Serikov, Il'ya B.; Althausen, Dietrich; Mattis, Ina; Wandinger, Ulla; Ansmann, Albert

    2001-04-01

    This lecture describes the development of lidar techniques to measure the atmospheric temperature profile. Particular attention is given in the lecture to the technique that uses pure rotational Raman scattering of light by molecular nitrogen and oxygen. At present, this approach to temperature profiling in the atmosphere with lidars has received a new impulse because of recent advances in laser and optoelectronics technologies. The instrumentation aspects that determine the feasibility of one or another lidar technique to measure temperature profiles based on the pure rotational Raman spectrum (PRRS) of N2 and O2 molecules are considered. The primary instrumental problem is isolation of extremely weak Raman-lidar returns within the PRRS of N2 and O2 against the background from the much stronger line of unshifted scattering. Mie + Rayleigh, that simultaneously contributes to lidar returns. Besides, the daytime sky background is the factor that severely hampers daytime lidar measurements especially in the case with Raman lidars. So it is an important task of Raman-lidar technologists to find proper ways to overcome this difficulty that would made it possible the temperature profiling in the atmosphere to be performed whole day round. The approach to achieving this task by use of a Fabry-Perot interferometer (FPI) is discussed in the lecture.

  19. Water level sensor and temperature profile detector

    International Nuclear Information System (INIS)

    Tokarz, R.D.

    1983-01-01

    A temperature profile detector comprising a surrounding length of metal tubing and an interior electrical conductor both constructed of high temperature high electrical resistance materials. A plurality of gas-filled expandable bellows made of electrically conductive material is electrically connected to the interior electrical conductor and positioned within the length of metal tubing. The bellows are sealed and contain a predetermined volume of a gas designed to effect movement of the bellows from an open circuit condition to a closed circuit condition in response to monitored temperature changes sensed by each bellows

  20. Theoretical studies of hollow electron temperature profiles

    International Nuclear Information System (INIS)

    Werkoff, F.; Mercier, C.; Cissoko, G.

    1978-06-01

    The basic mechanisms of experimentally obtained hollow profiles of electron temperature have been investigated. These hollow profiles are obviously related to radiative losses at the center of the plasma, losses that are greater than Joule heating. Hollow profiles were numerically and analytically shown to be instable of the MHD point of view, when the heat diffusion coefficient of electrons is too small. Taking Ksub(e) high enough to satisfy the stability criterion, steady states were obtained in agreement with experimental results. The impurities at the center of the plasma were also shown to be far from the coronal equilibrium. Accoding to neo-classical laws, this discrepancy entails the impurity accumulation at the plasma center, in correlation with an adequately hollow Tsub(e) profile. It was also proved that, at least in a certain range of parameters, the initial conditions can be chosen so as to obtain either a steady peaked state or a steady hollow state [fr

  1. Measuring Density Profiles of Electrons and Heavy Particles in a Stable Axially Blown Arc

    Science.gov (United States)

    Carstensen, J.; Stoller, P.; Galletti, B.; Doiron, C. B.; Sokolov, A.

    2017-08-01

    Two-color spatial carrier wave interferometry employing pulsed 532- and 671-nm lasers is used to measure the electron-density and heavy-particle-density profiles in the stagnation point of a stable, axially blown arc in argon for currents of 50 to 200 A and stagnation point pressures of 0.2 to 16 bar. This technique takes advantage of the fact that the free-electron contribution to the refractive index depends strongly on the wavelength, while that of the heavy particles does not. The high spatial resolution achieved allows the hot core of the arc to be readily distinguished from the surrounding boundary layer. A custom-built test device is used to ensure flow conditions that lead to a stable, axisymmetric arc; this permits the reconstruction of the density and temperature profiles using a single projection (interferometric image) of the refractive-index distribution through the arc (at two wavelengths). The arc radius determined from the heavy-particle density decreases with increasing stagnation pressure and increases with the current. These measurements are in good agreement with a simple axially blown arc model taking into account Ohmic heating, radiation losses, and enthalpy flow for core temperatures of approximately 16 500 K. The measured electron density at the center of the arc agrees well with a prediction based on local thermodynamic equilibrium.

  2. Temperature Compensated Sapphire Resonator for Ultra-Stable Oscillator Capability at Temperatures Above 77 Kelvin

    Science.gov (United States)

    Dick, G.; Santiago, D.; Wang, R.

    1994-01-01

    We report on the design and test of a whispering gallery sapphire resonator for which the dominant (WGH xxxsubn11) microwave mode family shows frequency-stable, compensated operation for temperatures above 77 Kelvin. The resonator makes possible a new ultra-stable oscillator (USO) capability that promises performance improvements over the best available crystal quartz oscillators in a compact cryogenic package. A mechanical compensation mechanism, enabled by the difference between copper and sapphire expansion coefficients, tunes the resonator to cancel the temperature variation of sapphire's dielectric constant.

  3. Temperature profiles in high gradient furnaces

    Science.gov (United States)

    Fripp, A. L.; Debnam, W. J.; Woodell, G. A.; Berry, R.; Crouch, R. K.; Sorokach, S. K.

    1989-01-01

    Accurate temperature measurement of the furnace environment is very important in both the science and technology of crystal growth as well as many other materials processing operations. A high degree of both accuracy and precision is acutely needed in the directional solidification of compound semiconductors in which the temperature profiles control the freezing isotherm which, in turn, affects the composition of the growth with a concomitant feedback perturbation on the temperature profile. Directional solidification requires a furnace configuration that will transport heat through the sample being grown. A common growth procedure is the Bridgman Stockbarger technique which basically consists of a hot zone and a cold zone separated by an insulator. In a normal growth procedure the material, contained in an ampoule, is melted in the hot zone and is then moved relative to the furnace toward the cold zone and solidification occurs in the insulated region. Since the primary path of heat between the hot and cold zones is through the sample, both axial and radial temperature gradients exist in the region of the growth interface. There is a need to know the temperature profile of the growth furnace with the crystal that is to be grown as the thermal load. However it is usually not feasible to insert thermocouples inside an ampoule and thermocouples attached to the outside wall of the ampoule have both a thermal and a mechanical contact problem as well as a view angle problem. The objective is to present a technique of calibrating a furnace with a thermal load that closely matches the sample to be grown and to describe procedures that circumvent both the thermal and mechanical contact problems.

  4. Blood temperature profiles of diving elephant seals.

    Science.gov (United States)

    Meir, Jessica U; Ponganis, Paul J

    2010-01-01

    Hypothermia-induced reductions in metabolic rate have been proposed to suppress metabolism and prolong the duration of aerobic metabolism during dives of marine mammals and birds. To determine whether core hypothermia might contribute to the repetitive long-duration dives of the northern elephant seal Mirounga angustirostris, blood temperature profiles were obtained in translocated juvenile elephant seals equipped with a thermistor and backpack recorder. Representative temperature (the y-intercept of the mean temperature vs. dive duration relationship) was 37.2 degrees C +/- 0.6 degrees C (n=3 seals) in the extradural vein, 38.1 degrees C +/- 0.7 degrees C (n = 4 seals) in the hepatic sinus, and 38.8 degrees +/- 1.6 degrees C (n = 6 deals) in the aorta. Mean temperature was significantly though weakly negatively related to dive duration in all but one seal. Mean venous temperatures of all dives of individual seals ranged between 36 degrees and 38 degrees C, while mean arterial temperatures ranged between 35 degrees and 39 degrees C. Transient decreases in venous and arterial temperatures to as low as 30 degrees -33 degrees C occurred in some dives >30 min (0.1% of dives in the study). The lack of significant core hypothermia during routine dives (10-30 min) and only a weak negative correlation of mean temperature with dive duration do not support the hypothesis that a cold-induced Q(10) effect contributes to metabolic suppression of central tissues during dives. The wide range of arterial temperatures while diving and the transient declines in temperature during long dives suggest that alterations in blood flow patterns and peripheral heat loss contribute to thermoregulation during diving.

  5. CAMEX-4 ER-2 MICROWAVE TEMPERATURE PROFILER V1

    Data.gov (United States)

    National Aeronautics and Space Administration — The CAMEX-4 ER-2 Microwave Temperature Profiler dataset was collected by the Microwave Temperature Profiler (MTP), which is a passive microwave radiometer which...

  6. TCSP ER-2 MICROWAVE TEMPERATURE PROFILER (MTP) V1

    Data.gov (United States)

    National Aeronautics and Space Administration — The TCSP ER-2 Microwave Temperature Profiler (MTP) dataset was collected by the ER-2 Microwave Temperature Profiler (MTP), which is a passive microwave radiometer...

  7. Phosphoproteome profiling for cold temperature perception.

    Science.gov (United States)

    Park, Seyeon; Jang, Mi

    2011-02-01

    Temperature sensation initiates from the activation of cellular receptors when the cell is exposed to a decrease in temperature. Here, we applied a phosphoproteome profiling approach to the human lung epithelial cell line BEAS-2B to elucidate cellular cold-responsive processes. The primary aim of this study was to determine which intracellular changes of phosphorylation are accompanied by cold sensation. Eighteen protein spots that exhibited differentially phosphorylated changes in cells were identified. Most of the proteins that were phosphorylated after 5 or 10 min were returned to control levels after 30 or 60 min. Identified proteins were mainly RNA-related (i.e., they were involved in RNA binding and splicing). Temperature (18 and 10°C) stimuli showed homologies that were detected for time course changes in phosphoproteome. The data indicated a time-shift between two temperatures. The phosphorylation of putative cold responsive markers, such as ribosomal protein large P0 and heterochromatin-associated proteins 1, were verified by Western blotting in cells transfected with TRPM8 or TRPA1. Copyright © 2010 Wiley-Liss, Inc.

  8. Temperature profiles of sleeveless and coaxial phacoemulsification.

    Science.gov (United States)

    Abulafia, Adi; Michaeli, Adi; Belkin, Avner; Assia, Ehud I

    2013-11-01

    To study the temperature profile at the corneal wound during 2 sleeveless techniques versus 2 coaxial phacoemulsification techniques. Department of Ophthalmology, Meir Medical Center, Kfar Saba and Ein-Tal Eye Center, Tel-Aviv, Israel. Experimental study. Thirty-six porcine eyes were randomized into 4 groups: Group 1: conventional coaxial system (3.0 mm incision); Group 2: coaxial microincision cataract surgery (MICS) system (2.2 mm incision); Group 3: bimanual MICS (1.1 mm incision); Group 4: sleeveless tri-MICS (1.1 mm incision) using a 19-gauge anterior chamber maintainer as the sole fluid source. Temperature measurements were taken using a thermocouple and an infrared thermal imaging system. Measurements were taken in 2 settings; that is, with and without occlusion. With no occlusion, corneal burns did not occur in any group. However, corneal temperatures were lower with the sleeveless systems (Groups 3 and 4) than with the coaxial systems (Groups 1 and 2) (P=.0003). When occlusion was induced, temperatures were kept constantly low in the sleeveless groups, whereas in the coaxial groups, temperatures increased rapidly, causing corneal burns within seconds. The mean temperature elevations at the incision sites were 39 °C, 48.5 °C, 13.6 °C, and 11.3 °C in Groups 1, 2, 3, and 4, respectively (Ptemperatures than sleeved coaxial methods. During occlusion, fluid flow around the naked tip of the sleeveless systems prevented heat accumulation and corneal burns. Copyright © 2013 ASCRS and ESCRS. All rights reserved.

  9. Modeling the wafer temperature profile in a multiwafer LPCVD furnace

    Energy Technology Data Exchange (ETDEWEB)

    Badgwell, T.A. [Rice Univ., Houston, TX (United States). Dept. of Chemical Engineering; Trachtenberg, I.; Edgar, T.F. [Univ. of Texas, Austin, TX (United States). Dept. of Chemical Engineering

    1994-01-01

    A mathematical model has been developed to predict wafer temperatures within a hot-wall multiwafer low pressure chemical vapor deposition (LPCVD) reactor. The model predicts both axial (wafer-to-wafer) and radial (across-wafer) temperature profiles. Model predictions compare favorably with in situ wafer temperature measurements described in an earlier paper. Measured axial and radial temperature nonuniformities are explained in terms of radiative heat-transfer effects. A simulation study demonstrates how changes in the outer tube temperature profile and reactor geometry affect wafer temperatures. Reactor design changes which could improve the wafer temperature profile are discussed.

  10. Global Temperature and Salinity Profile Programme (GTSPP) Data, 1985-present

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Global Temperature-Salinity Profile Programme (GTSPP) develops and maintains a global ocean temperature and salinity resource with data that are both up-to-date...

  11. Platinum thin film resistors as accurate and stable temperature sensors

    Science.gov (United States)

    Diehl, W.

    1984-01-01

    The measurement characteristics of thin-Pt-film temperature sensors fabricated using advanced methods are discussed. The limitations of wound-wire Pt temperature sensors and the history of Pt-film development are outlined, and the commonly used film-deposition, structuring, and trimming methods are presented in a table. The development of a family of sputtered film resistors is described in detail and illustrated with photographs of the different types. The most commonly used tolerances are reported as + or - 0.3 C + 0.5 percent of the temperature measured.

  12. High Temperature Stable Nanocrystalline SiGe Thermoelectric Material

    Science.gov (United States)

    Yang, Sherwin (Inventor); Matejczyk, Daniel Edward (Inventor); Determan, William (Inventor)

    2013-01-01

    A method of forming a nanocomposite thermoelectric material having microstructural stability at temperatures greater than 1000 C. The method includes creating nanocrystalline powder by cryomilling. The method is particularly useful in forming SiGe alloy powder.

  13. A behavioral and cognitive profile of clinically stable HIV-infected children

    NARCIS (Netherlands)

    Nozyce, ML; Lee, SS; Wiznia, A; Nachman, S; Mofenson, LM; Smith, ME; Yogev, R; McIntosh, K; Stanley, K; Pelton, S

    OBJECTIVE. The purpose of this research was to characterize behavioral and cognitive profiles of clinically and immunologically stable antiretroviral-experienced HIV-infected children. METHODS. Two hundred seventy-four previously treated HIV-infected children aged 2 to 17 years were assessed for

  14. Interpreting Repeated Temperature-Depth Profiles for Groundwater Flow

    Science.gov (United States)

    Bense, Victor F.; Kurylyk, Barret L.; van Daal, Jonathan; van der Ploeg, Martine J.; Carey, Sean K.

    2017-10-01

    Temperature can be used to trace groundwater flows due to thermal disturbances of subsurface advection. Prior hydrogeological studies that have used temperature-depth profiles to estimate vertical groundwater fluxes have either ignored the influence of climate change by employing steady-state analytical solutions or applied transient techniques to study temperature-depth profiles recorded at only a single point in time. Transient analyses of a single profile are predicated on the accurate determination of an unknown profile at some time in the past to form the initial condition. In this study, we use both analytical solutions and a numerical model to demonstrate that boreholes with temperature-depth profiles recorded at multiple times can be analyzed to either overcome the uncertainty associated with estimating unknown initial conditions or to form an additional check for the profile fitting. We further illustrate that the common approach of assuming a linear initial temperature-depth profile can result in significant errors for groundwater flux estimates. Profiles obtained from a borehole in the Veluwe area, Netherlands in both 1978 and 2016 are analyzed for an illustrative example. Since many temperature-depth profiles were collected in the late 1970s and 1980s, these previously profiled boreholes represent a significant and underexploited opportunity to obtain repeat measurements that can be used for similar analyses at other sites around the world.

  15. Determining the Temperature Profile in a Cylindrical Sample

    Science.gov (United States)

    Clayton, J. C.

    1986-01-01

    Power-series solution extrapolates from axial temperature profile. Thermal profile in homogeneous axisymmetric body determined throughout body if axial temperature profile known at any radius. New theory developed as aid in research on growth of mercury cadmium telluride for infrared detectors. In particular, applicable to Bridgman-Stockbarger growth, in which round cylindrical ampoule of molten ternary semiconductor is solidified directionally, from one end to other.

  16. Temperature and velocity profiles in sooting free boundary layer flames

    Science.gov (United States)

    Ang, J. A.; Pagni, P. J.; Mataga, T. G.; Margle, J. M.; Lyons, V. J.

    1986-01-01

    Temperature and velocity profiles are presented for cyclohexane, n-heptane, and iso-octane free, laminar, boundary layer, sooting, diffusion flames. Temperatures are measured with 3 mil Pt/Pt-13 percent Rh thermocouples. Corrected gas temperatures are derived by performing an energy balance of convection to and radiation from the thermocouple bead incorporating the variation of air conductivity and platinum emissivity with temperature. Velocities are measured using laser doppler velocimetry techniques. Profiles are compared with previously reported analytic temperature and velocity fields. Comparison of theoretical and experimental temperature profiles suggests improvement in the analytical treatment is needed, which accounts more accurately for the local soot radiation. The velocity profiles are in good agreement, with the departure of the theory from observation partially due to the small fluctuations inherent in these free flows.

  17. Acoustic temperature profile measurement technique for large combustion chambers

    Science.gov (United States)

    Venkateshan, S. P.; Shakkottai, P.; Kwack, E. Y.; Back, L. H.

    1989-01-01

    Measurement of times of flight of sound waves can be used to determine temperatures in a gas. This paper describes a system, based on this principle, that is capable of giving the temperature profile in a nonisothermal gas volume, for example, prevalent in a large furnace. The apparatus is simple, rugged, accurate, and capable of being automated for process control applications. It is basically an acoustic waveguide where the outside temperature profile is transferred to a chosen gas contained inside the guide.

  18. Precipitation and temperature effects on stable fly (diptera: muscidae) population dynamics

    Science.gov (United States)

    The dynamics of stable fly, Stomoxys calcitrans (L.), populations relative to temperature and precipitation were evaluated in a 13 y study in eastern Nebraska. During the course of the study, over 1.7 million stable flies were collected on an array of 25 sticky traps. A log-normal model using degree...

  19. A temperature-stable cryo-system for high-temperature superconducting MR in-vivo imaging.

    Directory of Open Access Journals (Sweden)

    In-Tsang Lin

    Full Text Available To perform a rat experiment using a high-temperature superconducting (HTS surface resonator, a cryostat is essential to maintain the rat's temperature. In this work, a compact temperature-stable HTS cryo-system, keeping animal rectal temperature at 37.4°C for more than 3 hours, was successfully developed. With this HTS cryo-system, a 40-mm-diameter Bi2Sr2Ca2Cu3Ox (Bi-2223 surface resonator at 77 K was demonstrated in a 3-Tesla MRI system. The proton resonant frequency (PRF method was employed to monitor the rat's temperature. Moreover, the capacity of MR thermometry in the HTS experiments was evaluated by correlating with data from independent fiber-optic sensor temperature measurements. The PRF thermal coefficient was derived as 0.03 rad/°C and the temperature-monitoring architecture can be implemented to upgrade the quality and safety in HTS experiments. The signal-to-noise ratio (SNR of the HTS surface resonator at 77 K was higher than that of a professionally made copper surface resonator at 300 K, which has the same geometry, by a 3.79-fold SNR gain. Furthermore, the temperature-stable HTS cryo-system we developed can obtain stable SNR gain in every scan. A temperature-stable HTS cryo-system with an external air-blowing circulation system is demonstrated.

  20. Stable room-temperature thallium bromide semiconductor radiation detectors

    Science.gov (United States)

    Datta, A.; Fiala, J.; Becla, P.; Motakef, Shariar

    2017-10-01

    Thallium bromide (TlBr) is a highly efficient ionic semiconductor with excellent radiation detection properties. However, at room temperature, TlBr devices polarize under an applied electric field. This phenomenon not only degrades the charge collection efficiency of the detectors but also promotes chemical reaction of the metal electrodes with bromine, resulting in an unstable electric field and premature failure of the device. This drawback has been crippling the TlBr semiconductor radiation detector technology over the past few decades. In this exhaustive study, this polarization phenomenon has been counteracted using innovative bias polarity switching schemes. Here the highly mobile Br- species, with an estimated electro-diffusion velocity of 10-8 cm/s, face opposing electro-migration forces during every polarity switch. This minimizes the device polarization and availability of Br- ions near the metal electrode. Our results indicate that it is possible to achieve longer device lifetimes spanning more than 17 000 h (five years of 8 × 7 operation) for planar and pixelated radiation detectors using this technique. On the other hand, at constant bias, 2500 h is the longest reported lifetime with most devices less than 1000 h. After testing several biasing switching schemes, it is concluded that the critical bias switching frequency at an applied bias of 1000 V/cm is about 17 μHz. Using this groundbreaking result, it will now be possible to deploy this highly efficient room temperature semiconductor material for field applications in homeland security, medical imaging, and physics research.

  1. Stable room-temperature thallium bromide semiconductor radiation detectors

    Directory of Open Access Journals (Sweden)

    A. Datta

    2017-10-01

    Full Text Available Thallium bromide (TlBr is a highly efficient ionic semiconductor with excellent radiation detection properties. However, at room temperature, TlBr devices polarize under an applied electric field. This phenomenon not only degrades the charge collection efficiency of the detectors but also promotes chemical reaction of the metal electrodes with bromine, resulting in an unstable electric field and premature failure of the device. This drawback has been crippling the TlBr semiconductor radiation detector technology over the past few decades. In this exhaustive study, this polarization phenomenon has been counteracted using innovative bias polarity switching schemes. Here the highly mobile Br− species, with an estimated electro-diffusion velocity of 10−8 cm/s, face opposing electro-migration forces during every polarity switch. This minimizes the device polarization and availability of Br− ions near the metal electrode. Our results indicate that it is possible to achieve longer device lifetimes spanning more than 17 000 h (five years of 8 × 7 operation for planar and pixelated radiation detectors using this technique. On the other hand, at constant bias, 2500 h is the longest reported lifetime with most devices less than 1000 h. After testing several biasing switching schemes, it is concluded that the critical bias switching frequency at an applied bias of 1000 V/cm is about 17 μHz. Using this groundbreaking result, it will now be possible to deploy this highly efficient room temperature semiconductor material for field applications in homeland security, medical imaging, and physics research.

  2. Steady state temperature profile in a sphere heated by microwaves

    Science.gov (United States)

    Barmatz, M.; Jackson, H. W.

    1992-01-01

    A new theory has been developed to calculate the microwave absorption and resultant temperature profile within a sphere positioned in a single mode rectangular cavity. This theory is an extension of a total absorption model based on Mie scattering results. Temperature profiles have been computed for alumina spheres at the center of a rectangular cavity excited in the TM354 mode. Parametric studies reveal significant structure in those profiles under special conditions that are associated with electromagnetic resonances inside the spheres. Anomalous behavior similar to thermal runaway occurs at moderate temperatures when there is enhanced absorption associated with resonant conditions in the sphere.

  3. Initial temperature profiles of the PDX inner toroidal limiter

    International Nuclear Information System (INIS)

    Ulrickson, M.; Kugel, H.W.

    1983-01-01

    The temperature profiles resulting from plasma operation on the PDX vertical, large area, inner toroidal limiter have been measured during both ohmic and neutral beam heated discharges using a scanning infrared camera. An asymmetric double peaked temperature profile is seen after neutral beam heated discharges. Disruptions in ohmically heated discharges are found to be preceded by a single peaked deposition and succeeded by a initially symmetric double peaked deposition. The results were compared with the Schmidt model for scrapeoff at a toroidal limiter and it was found that the measured double peaked temperature profiles yielded scrape-off lengths consistent with previous measurements

  4. Nonequilibrium shock layer temperature profiles from arc jet radiation measurements

    Science.gov (United States)

    Blackwell, Harvel E.; Yuen, Eric; Scott, Carl D.; Arepalli, Sivaram

    1989-01-01

    Shock layer temperature profiles are obtained through analysis of radiation from shock layers produced by a blunt body inserted in arc jet flow. Spectral measurements have been made in a nitrogen flow of 54.4 gm/s at an enthalpy of 8.72 MJ/kg. Vibrational temperatures for N2+ are obtained by matching spectral regions from arc jet spectra with spectra generated using the NEQAIR code. Temperature profiles obtained from the radiation layers show a vibrational temperature higher than the rotational temperature near the front of the shock and both temperatures decrease as the flow approaches the body. The spectral measurements are made and analysis completed for four distances, from the surface of the blunt body. The corresponding shock layer thickness is approximately 3.6 cm. Although the shock layer appears to be in thermal nonequilibrium, the measured rotational temperature approaches the single temperature results of viscous shock layer calculations at this test condition.

  5. Optimal Detection of Global Warming using Temperature Profiles

    Science.gov (United States)

    Leroy, Stephen S.

    1997-01-01

    Optimal fingerprinting is applied to estimate the amount of time it would take to detect warming by increased concentrations of carbon dioxide in monthly averages of temperature profiles over the Indian Ocean.

  6. CAMEX-4 DC-8 MICROWAVE TEMPERATURE PROFILER (MTP) V1

    Data.gov (United States)

    National Aeronautics and Space Administration — The Microwave Temperature Profiler (MTP) is a passive microwave radiometer which measures the thermal emmission from oxygen molecules in the atmosphere for a...

  7. CAMEX-4 ER-2 MICROWAVE TEMPERATURE PROFILER V1

    Data.gov (United States)

    National Aeronautics and Space Administration — The Microwave Temperature Profiler (MTP) is a passive microwave radiometer which measures the thermal emmission from oxygen molecules in the atmosphere for a...

  8. CAMEX-4 DC-8 MICROWAVE TEMPERATURE PROFILER (MTP) V1

    Data.gov (United States)

    National Aeronautics and Space Administration — The CAMEX-4 DC-8 Microwave Temperature Profiler (MTP) dataset was collected by the MTP, which is a passive microwave radiometer used during the CAMEX-4 campaign to...

  9. Initialization of a mesoscale model with satellite derived temperature profiles

    Science.gov (United States)

    Kalb, Michael W.

    1986-01-01

    The abilities of rawinsonde data and Tiros-N satellite derived temperature profile data to depict mesoscale precipitation accumulation are evaluated. Four mesoscale simulations using combinations of temperature, low-level wind, and low-level wind initialization were performed with the limited area mesoscale prediction system (LAMPS) model. Comparisons of the simulations with operational LFM forecast accumulations reveal that the LAMPS model simulations provide a better depiction of the observed precipitation accumulation than the LFM forecasts, and the satellite temperature profiles produce better mesoscale precipitation accumulation forecasts than the rawinsonde temperature data.

  10. Logarithmic temperature profiles in the ultimate regime of thermal convection

    NARCIS (Netherlands)

    Grossmann, S.; Lohse, Detlef

    2012-01-01

    We report on the theory of logarithmic temperature profiles in very strongly developed thermal convection in the geometry of a Rayleigh-Bénard cell with aspect ratio (defined by cell width divided by cell height) Γ = 1, and discuss the degree of agreement with the recently measured profiles in the

  11. Entropy production and transport in relation to Tokamak temperature profiles

    International Nuclear Information System (INIS)

    Martinell, J.J.; Almaguer, J.A.; Herrera, J.J.E.

    1992-01-01

    The consequences of using the idea of entropy production rate minimization are examined in relation to the shape of radial temperature profiles and the scaling of transport coefficients with temperature in Tokamak discharges. This is done under the assumption that physical processes occur in such a way as to produce relaxed states where an extremal of some relevant quantity (in this case the entropy production) is obtained. The conditions under which the temperature profiles adopt the Gaussian-like shapes observed in Tokamak plasmas are studied. This is possible only for certain scalings of the thermal conductivity with temperature favouring certain models of anomalous transport against others. These results are also dependent on whether or not the current density profile is assumed to be determined by the temperature profile, as in Ohmically heated discharges with constant electric field. In the former case an anomalous electrical resistivity is needed in order to obtain the correct temperature profiles for known models of anomalous thermal conductivity. When the current density is an independent function of radius the electrical resistivity can be classical, and for the thermal diffusivity this approach favours the models based on magnetic fluctuations exhibiting the Ohkawa scaling, as well as a model that employs profile consistency in its derivations. These cases should be relevant to discharges with auxiliary heating. (Author)

  12. Using Distributed Temperature Sensing for measuring vertical temperature profiles and air temperature variance in the roughness sublayer above a forest canopy

    Science.gov (United States)

    Schilperoort, B.; Coenders, M.; Savenije, H. H. G.

    2017-12-01

    In recent years, the accuracy and resolution of Distributed Temperature Sensing (DTS) machines has increased enough to expand its use in atmospheric sciences. With DTS the temperature of a fiber optic (FO) cable can be measured with a high frequency (1 Hz) and high resolution (0.30 m), for cable lengths up to kilometers. At our measurement site, a patch of 26 to 30 m tall Douglas Fir in mixed forest, we placed FO cables vertically along a 48 m tall flux tower. This gives a high resolution vertical temperature profile above, through, and below the canopy. By using a `bare' FO cable, with a diameter of 0.25 mm, we are able to measure variations in air temperature at a very small timescale, and are able to measure a vertical profile of the air temperature variance. The vertical temperature profiles can be used to study the formation of the stable boundary layer above and in the canopy at a high resolution. It also shows that a stable layer can develop below the canopy, which is not limited to night time conditions but also occurs during daytime. The high frequency measurements can be used to study the gradient of the variance of air temperature over the height. To study how the flux tower itself affects temperature variance measurements, the `bare' FO cable can be placed horizontally under a support structure away from the flux tower. Lastly, by using the hot-wire anemometer principle with DTS, the measurements can be expanded to also include vertical wind profile.

  13. Space potential, temperature, and density profile measurements on RENTOR

    International Nuclear Information System (INIS)

    Schoch, P.M.

    1983-05-01

    Radial profiles of the space potential, electron temperature, and density have been measured on RENTOR with a heavy-ion-beam probe. The potential profile has been compared to predictions from a stochastic magnetic field fluctuation theory, using the measured temperature and density profiles. The comparison shows strong qualitative agreement in that the potential is positive and the order of T/sub e//e. There is some quantitative disagreement in that the measured radial electric fields are somewhat smaller than the theoretical predictions. To facilitate this comparison, a detailed analysis of the possible errors has been completed

  14. Comparison of RASS temperature profiles with other tropospheric soundings

    Science.gov (United States)

    Bonino, G.; Lombardini, P. P.; Trivero, P.

    1980-06-01

    The vertical temperature profile of the lower troposphere can be measured with a radio-acoustic sounding system (RASS). A comparison of the thermal profiles measured with the RASS and with traditional methods shows (1) RASS ability to produce vertical thermal profiles at an altitude range of 170 to 1000 m with temperature accuracy and height discrimination comparable with conventional soundings, (2) advantages of remote sensing as offered by new sounder, (3) applicability of RASS both in assessing evolution of thermodynamic conditions in PBL and in sensing conditions conducive to high concentrations of air pollutants at the ground level.

  15. Comparison of RASS temperature profiles with other tropospheric soundings

    International Nuclear Information System (INIS)

    Bonino, G.; Lombardini, P.P.; Trivero, P.

    1980-01-01

    The vertical temperature profile of the lower troposphere can be measured with a radio-acoustic sounding system (RASS). A comparison of the thermal profiles measured with the RASS and with traditional methods shows a) RASS ability to produce vertical thermal profiles at an altitude range of 170 to 1000 m with temperature accuracy and height discrimination comparable with conventional soundings, b) advantages of remote sensing as offered by new sounder, c) applicability of RASS both in assessing evolution of thermodynamic conditions in PBL and in sensing conditions conducive to high concentrations of air pollutants at the ground level. (author)

  16. Interpreting Repeated Temperature-Depth Profiles for Groundwater Flow

    NARCIS (Netherlands)

    Bense, Victor F.; Kurylyk, Barret L.; Daal, van Jonathan; Ploeg, van der Martine J.; Carey, Sean K.

    2017-01-01

    Temperature can be used to trace groundwater flows due to thermal disturbances of subsurface advection. Prior hydrogeological studies that have used temperature-depth profiles to estimate vertical groundwater fluxes have either ignored the influence of climate change by employing steady-state

  17. Logarithmic Temperature Profiles in Turbulent Rayleigh-Benard Convection

    NARCIS (Netherlands)

    Ahlers, G.; Bodenschatz, E.; Funfschilling, D.; Grossmann, S.; He, Xiaozhou; Lohse, Detlef; Stevens, Richard Johannes Antonius Maria; Verzicco, Roberto

    2012-01-01

    We report results for the temperature profiles of turbulent Rayleigh-Bénard convection (RBC) in the interior of a cylindrical sample of aspect ratio ¿¿D/L=0.50 (D and L are the diameter and height, respectively). Both in the classical and in the ultimate state of RBC we find that the temperature

  18. Temperature profile evolution in quenching high-Tc ...

    Indian Academy of Sciences (India)

    temperature superconductors (HTS) in ... can lead to serious thermal stresses within the winding pack of the high-Tc superconduc- tor. Thus, the ... The motivation for the present work is the desire that all important temperature profile evolutions must ...

  19. Strong anisotropy in the low temperature Compton profiles of ...

    Indian Academy of Sciences (India)

    Abstract. Compton profiles of momentum distribution of conduction electrons in the orthorhom- bic phase of α-Ga metal at low temperature are calculated in the band model for the three crys- tallographic directions (100), (010), and (001). Unlike the results at room temperature, previously reported by Lengeler, Lasser and ...

  20. Lower atmospheric temperature profile measurements using a Raman lidar

    Science.gov (United States)

    Melfi, S. H.; Whiteman, D.

    1986-01-01

    A Raman lidar system was used to measure the temperature profile of the upper troposphere and lower stratosphere. The system consists of a tripled Nd-YAG laser and a 1.5 meter diameter telescope. Two photomultipliers are used at the output of the telescope to allow for measurements at both the laser wavelength and at the Raman shifted wavelength due to atmospheric nitrogen. The signal from the photomultipliers is recorded as photon counts in 1 microsec bins. The results of a number of laser shots are summed together to provide atmospheric returns which have acceptable signal to noise characteristics. Measurements of the Raman nitrogen return were acquired up to an altitude in excess of 20 km. Temperature profiles were retrieved from the attenuation corrected Raman nitrogen return assuming the atmosphere to be in hydrostatic equilibrium and using the ideal gas law. Retrieved temperature profiles are shown compared with independent temperature measurements.

  1. Eocene Antarctic seasonality inferred from high-resolution stable isotope profiles of fossil bivalves and driftwood

    Science.gov (United States)

    Judd, E. J.; Ivany, L. C.; Miklus, N. M.; Uveges, B. T.; Junium, C. K.

    2017-12-01

    The Eocene Epoch was a time of large-scale global climate change, experiencing both the warmest temperatures of the Cenozoic and the onset of southern hemisphere glaciation. The record of average global temperatures throughout this transition is reasonably well constrained, however considerably less is known about the accompanying changes in seasonality. Seasonally resolved temperature data provide a wealth of information not readily available from mean annual temperature data alone. These data are particularly important in the climatically sensitive high latitudes, as they can elucidate the means by which climate changes and the conditions necessary for the growth of ice sheets. Several recent studies, however, have suggested the potential for monsoonal precipitation regimes in the early-middle Eocene high latitudes, which complicates interpretation of seasonally resolved oxygen isotope records in shallow nearshore marine settings. Seasonal precipitation and runoff could create a brackish, isotopically depleted lens in these environments, depleting summertime δ18Ocarb and thereby inflating the inferred mean and range of isotope-derived temperatures. Here, we assess intra-annual variations in temperature in shallow nearshore Antarctic waters during the middle and late Eocene, inferred from high-resolution oxygen isotope profiles from accretionary bivalves of the La Meseta Formation, Seymour Island, Antarctica. To address concerns related to precipitation and runoff, we also subsample exceptionally preserved fossil driftwood from within the formation and use seasonal differences in δ13Corg values to estimate the ratio of summertime to wintertime precipitation. Late Eocene oxygen isotope profiles exhibit strongly attenuated seasonal amplitudes and more enriched mean annual values in comparison with data from the middle Eocene. Preliminary fossil wood data are not indicative of a strongly seasonal precipitation regime, implying that intra-annual variation in oxygen

  2. Temperature profiles of patient-applied eyelid warming therapies.

    Science.gov (United States)

    Wang, Michael T M; Gokul, Akilesh; Craig, Jennifer P

    2015-12-01

    To compare temperature profile characteristics (on and off eye) of two patient-applied heat therapies for meibomian gland dysfunction (MGD): an eye mask containing disposable warming units (EyeGiene(®)) and a microwave-heated flaxseed eye bag(®) (MGDRx EyeBag(®)). In vitro evaluation: surface temperature profiles of activated eye masks and heated eye bags(®) (both n=10), were tracked every 10s until return to ambient temperature. Heat-transfer assessment: outer and inner eyelid temperature profiles throughout the eye mask and eye bag(®) treatment application period (10min) were investigated in triplicate. The devices were applied for 12 different time intervals in a randomised order, with a cool-down period in between to ensure ocular temperatures returned to baseline. Temperature measurements were taken before and immediately after each application. In vitro evaluation: on profile, the eye bag(®) surface temperature peaked earlier (0±0 s vs. 100±20 s, ptemperatures (38.1±0.4°C vs. 37.4±0.2°C, p=0.04), as well as larger inner eyelid temperature increases over the first 2 min, and between 9 and 10 min (all ptemperature profile displayed greater uniformity and slower cooling than the eye mask, and was demonstrated to be significantly more effective in raising ocular temperatures than the eye mask, both statistically and clinically. This has implications for MGD treatment, where the melting points of meibomian secretions are likely to be higher with increasing disease severity. Copyright © 2015 Elsevier Ltd. All rights reserved.

  3. Steady State Temperature Profile in a Cylinder Heated by Microwaves

    Science.gov (United States)

    Jackson, H. W.; Barmatz, M.; Wagner, P.

    1995-01-01

    A new theory has been developed to calculate the steady state temperature profile in a cylindrical sample positioned along the entire axis of a cylindrical microwave cavity. Temperature profiles where computed for- alumina rods of various radii contained in a cavity excite in one of the TM(sub OnO) modes with n = 1, 2 or 3. Calculations where also performed with a concentric outer cylindrical tube surrounding the rod to investigate hybrid heating. The parameters studies of the sample center and surface temperature where performed as a function of the total power transmitted into the cavity. Also, the total hemispherical emissivity was varied at boundaries of the rod, surrounding tube, and cavity walls. The result are discussed in the context of controlling the average rod temperature and the temperature distribution in the rod during microwave processing.

  4. Time-Temperature Profiling of United Kingdom Consumers' Domestic Refrigerators.

    Science.gov (United States)

    Evans, Ellen W; Redmond, Elizabeth C

    2016-12-01

    Increased consumer demand for convenience and ready-to-eat food, along with changes to consumer food purchase and storage practices, have resulted in an increased reliance on refrigeration to maximize food safety. Previous research suggests that many domestic refrigerators operate at temperatures exceeding recommendations; however, the results of several studies were determined by means of one temperature data point, which, given temperature fluctuation, may not be a true indicator of actual continual operating temperatures. Data detailing actual operating temperatures and the effects of consumer practices on temperatures are limited. This study has collated the time-temperature profiles of domestic refrigerators in consumer kitchens (n = 43) over 6.5 days with concurrent self-reported refrigerator usage. Overall, the findings established a significant difference (P < 0.05) between one-off temperature (the recording of one temperature data point) and mean operating temperature. No refrigerator operated at ≤5.0°C for the entire duration of the study. Mean temperatures exceeding 5.0°C were recorded in the majority (91%) of refrigerators. No significant associations or differences were determined for temperature profiles and demographics, including household size, or refrigerator characteristics (age, type, loading, and location). A positive correlation (P < 0.05) between room temperature and refrigerator temperature was determined. Reported door opening frequency correlated with temperature fluctuation (P < 0.05). Thermometer usage was determined to be infrequent. Cumulatively, research findings have established that the majority of domestic refrigerators in consumer homes operate at potentially unsafe temperatures and that this is influenced by consumer usage. The findings from this study may be utilized to inform the development of shelf-life testing based on realistic domestic storage conditions. Furthermore, the data can inform the development of future

  5. A GAS TEMPERATURE PROFILE BY INFRARED EMISSION-ABSORPTION SPECTROSCOPY

    Science.gov (United States)

    Buchele, D. R.

    1994-01-01

    This computer program calculates the temperature profile of a flame or hot gas. Emphasis is on profiles found in jet engine or rocket engine exhaust streams containing water vapor or carbon dioxide as radiating gases. The temperature profile is assumed to be axisymmetric with a functional form controlled by two variable parameters. The parameters are calculated using measurements of gas radiation at two wavelengths in the infrared spectrum. Infrared emission and absorption measurements at two or more wavelengths provide a method of determining a gas temperature profile along a path through the gas by using a radiation source and receiver located outside the gas stream being measured. This permits simplified spectral scanning of a jet or rocket engine exhaust stream with the instrumentation outside the exhaust gas stream. This program provides an iterative-cyclic computation in which an initial assumed temperature profile is altered in shape until the computed emission and absorption agree, within specified limits, with the actual instrument measurements of emission and absorption. Temperature determination by experimental measurements of emission and absorption at two or more wavelengths is also provided by this program. Additionally, the program provides a technique for selecting the wavelengths to be used for determining the temperature profiles prior to the beginning of the experiment. By using this program feature, the experimenter has a higher probability of selecting wavelengths which will result in accurate temperature profile measurements. This program provides the user with a technique for determining whether this program will be sufficiently accurate for his particular application, as well as providing a means of finding the solution. The input to the program consists of four types of data: (1) computer program control constants, (2) measurements of gas radiance and transmittance at selected wavelengths, (3) tabulations from the literature of gas

  6. Soil Temperature and Moisture Profile (STAMP) System Handbook

    Energy Technology Data Exchange (ETDEWEB)

    Cook, David R. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-11-01

    The soil temperature and moisture profile system (STAMP) provides vertical profiles of soil temperature, soil water content (soil-type specific and loam type), plant water availability, soil conductivity, and real dielectric permittivity as a function of depth below the ground surface at half-hourly intervals, and precipitation at one-minute intervals. The profiles are measured directly by in situ probes at all extended facilities of the SGP climate research site. The profiles are derived from measurements of soil energy conductivity. Atmospheric scientists use the data in climate models to determine boundary conditions and to estimate the surface energy flux. The data are also useful to hydrologists, soil scientists, and agricultural scientists for determining the state of the soil. The STAMP system replaced the SWATS system in early 2016.

  7. Finite difference program for calculating hydride bed wall temperature profiles

    International Nuclear Information System (INIS)

    Klein, J.E.

    1992-01-01

    A QuickBASIC finite difference program was written for calculating one dimensional temperature profiles in up to two media with flat, cylindrical, or spherical geometries. The development of the program was motivated by the need to calculate maximum temperature differences across the walls of the Tritium metal hydrides beds for thermal fatigue analysis. The purpose of this report is to document the equations and the computer program used to calculate transient wall temperatures in stainless steel hydride vessels. The development of the computer code was motivated by the need to calculate maximum temperature differences across the walls of the hydrides beds in the Tritium Facility for thermal fatigue analysis

  8. Stable oxygen and carbon isotope profiles in an invasive bivalve ( Corbicula fluminea) in North Carolina watersheds

    Science.gov (United States)

    Bucci, John P.; Showers, William J.; Genna, Bernie; Levine, Jay F.

    2009-06-01

    The modern invasive bivalve Corbicula fluminea was collected in 2006 from three sites with different land uses located in a North Carolina River Basin. The primary objective was to describe the δ 18O and δ 13C profiles of C. fluminea shells under various land use conditions. An additional aim was to evaluate whether growth patterns of C. fluminea form seasonally. Annual shell growth patterns were measured from the umbo to the margin and co-varied with estimates of ambient water temperature, corresponding to seasonal variation. The C. fluminea growth patterns as translucent bands (slower growth) appeared to form during winter months and opaque bands (rapid growth) formed during summer. A mixed model analysis (ANOVA) showed a significant site level effect of δ 18O and δ 13C profiles examined among sites ( F = 17.1; p = 0.003). A second model showed a borderline significant site effect among profiles with variability more pronounced at the urban site, Crabtree Creek ( p = 0.085). Previous habitat assessment ratings and water chemistry measurements suggested that the urban site was more impacted by storm water runoff. Understanding δ 18O and δ 13C SHELL profiles and shell growth patterns of the invasive bivalve ( C. fluminea) may help establish a framework for using these animals as biomonitors to record water temperature and nutrient pollution.

  9. High-Temperature Adhesives for Thermally Stable Aero-Assist Technologies

    Science.gov (United States)

    Eberts, Kenneth; Ou, Runqing

    2013-01-01

    Aero-assist technologies are used to control the velocity of exploration vehicles (EVs) when entering Earth or other planetary atmospheres. Since entry of EVs in planetary atmospheres results in significant heating, thermally stable aero-assist technologies are required to avoid the high heating rates while maintaining low mass. Polymer adhesives are used in aero-assist structures because of the need for high flexibility and good bonding between layers of polymer films or fabrics. However, current polymer adhesives cannot withstand temperatures above 400 C. This innovation utilizes nanotechnology capabilities to address this need, leading to the development of high-temperature adhesives that exhibit high thermal conductivity in addition to increased thermal decomposition temperature. Enhanced thermal conductivity will help to dissipate heat quickly and effectively to avoid temperature rising to harmful levels. This, together with increased thermal decomposition temperature, will enable the adhesives to sustain transient high-temperature conditions.

  10. Gene expression profiles resulting from stable loss of p53 mirrors its role in tissue differentiation.

    Directory of Open Access Journals (Sweden)

    Oliver Couture

    Full Text Available The tumor suppressor gene p53 is involved in a variety of cellular activities such as cellular stress responses, cell cycle regulation and differentiation. In our previous studies we have shown p53's transcription activating role to be important in osteoblast differentiation. There is still a debate in the literature as to whether p53 inhibits or promotes differentiation. We have found p53 heterozygous mice to show a p53 dependency on some bone marker gene expression that is absent in knockout mice. Mice heterozygous for p53 also show a higher incidence of osteosarcomas than p53 knockout mice. This suggests that p53 is able to modify the environment within osteoblasts. In this study we compare changes in gene expression resulting after either a transient or stable reduction in p53. Accordingly we reduced p53 levels transiently and stably in C2C12 cells, which are capable of both myoblast and osteoblast differentiation, and compared the changes in gene expression of candidate genes regulated by the p53 pathway. Using a PCR array to assay for p53 target genes, we have found different expression profiles when comparing stable versus transient knockdown of p53. As expected, several genes with profound changes after transient p53 loss were related to apoptosis and cell cycle regulation. In contrast, stable p53 loss produced a greater change in MyoD and other transcription factors with tissue specific roles, suggesting that long term loss of p53 affects tissue homeostasis to a greater degree than changes resulting from acute loss of p53. These differences in gene expression were validated by measuring promoter activity of different pathway specific genes involved in differentiation. These studies suggest that an important role for p53 is context dependent, with a stable reduction in p53 expression affecting normal tissue physiology more than acute loss of p53.

  11. Source Attribution of Cyanides using Anionic Impurity Profiling, Stable Isotope Ratios, Trace Elemental Analysis and Chemometrics

    Energy Technology Data Exchange (ETDEWEB)

    Mirjankar, Nikhil S.; Fraga, Carlos G.; Carman, April J.; Moran, James J.

    2016-01-08

    Chemical attribution signatures (CAS) for chemical threat agents (CTAs) are being investigated to provide an evidentiary link between CTAs and specific sources to support criminal investigations and prosecutions. In a previous study, anionic impurity profiles developed using high performance ion chromatography (HPIC) were demonstrated as CAS for matching samples from eight potassium cyanide (KCN) stocks to their reported countries of origin. Herein, a larger number of solid KCN stocks (n = 13) and, for the first time, solid sodium cyanide (NaCN) stocks (n = 15) were examined to determine what additional sourcing information can be obtained through anion, carbon stable isotope, and elemental analyses of cyanide stocks by HPIC, isotope ratio mass spectrometry (IRMS), and inductively coupled plasma optical emission spectroscopy (ICP-OES), respectively. The HPIC anion data was evaluated using the variable selection methods of Fisher-ratio (F-ratio), interval partial least squares (iPLS), and genetic algorithm-based partial least squares (GAPLS) and the classification methods of partial least squares discriminate analysis (PLSDA), K nearest neighbors (KNN), and support vector machines discriminate analysis (SVMDA). In summary, hierarchical cluster analysis (HCA) of anion impurity profiles from multiple cyanide stocks from six reported country of origins resulted in cyanide samples clustering into three groups: Czech Republic, Germany, and United States, independent of the associated alkali metal (K or Na). The three country groups were independently corroborated by HCA of cyanide elemental profiles and corresponded to countries with known solid cyanide factories. Both the anion and elemental CAS are believed to originate from the aqueous alkali hydroxides used in cyanide manufacture. Carbon stable isotope measurements resulted in two clusters: Germany and United States (the single Czech stock grouped with United States stocks). The carbon isotope CAS is believed to

  12. Temperature profiles of Agaricus bisporus in composting stages and ...

    African Journals Online (AJOL)

    Three compost formulas using different activator materials were prepared for Agaricus bisporus cultivation. A locally available casing material known as peat of Bolu district and its different combinations with perlite were used. Temperature profiles of all mixtures during composting were measured at every composting stages ...

  13. Influence of temperature inhomogeneity on product profile of ...

    Indian Academy of Sciences (India)

    Unknown

    Influence of temperature inhomogeneity on product profile of reactions occurring within zeolites. ¶. A V ANIL KUMAR1, S YASHONATH1,2* and G ANANTHAKRISHNA2,3. 1Solid State and Structural Chemistry Unit, 2Centre for Condensed Matter. Theory, and 3Materials Research Centre, Indian Institute of Science,.

  14. Temperature profile evolution in quenching high-Tc ...

    Indian Academy of Sciences (India)

    Temperature profile evolution in quenching high-Tc superconducting composite tape. ZIAUDDIN KHAN1,∗. , SUBRATA PRADHAN1 and IRFAN AHMAD2. 1Institute for Plasma Research, Near Indira Bridge, Bhat, Gandhinagar 382 428, India. 2Shibli National College, Sikandarpur Market Road, Paharpur, Azamgarh 276 ...

  15. An optical fiber expendable seawater temperature/depth profile sensor

    Science.gov (United States)

    Zhao, Qiang; Chen, Shizhe; Zhang, Keke; Yan, Xingkui; Yang, Xianglong; Bai, Xuejiao; Liu, Shixuan

    2017-10-01

    Marine expendable temperature/depth profiler (XBT) is a disposable measuring instrument which can obtain temperature/depth profile data quickly in large area waters and mainly used for marine surveys, scientific research, military application. The temperature measuring device is a thermistor in the conventional XBT probe (CXBT)and the depth data is only a calculated value by speed and time depth calculation formula which is not an accurate measurement result. Firstly, an optical fiber expendable temperature/depth sensor based on the FBG-LPG cascaded structure is proposed to solve the problems of the CXBT, namely the use of LPG and FBG were used to detect the water temperature and depth, respectively. Secondly, the fiber end reflective mirror is used to simplify optical cascade structure and optimize the system performance. Finally, the optical path is designed and optimized using the reflective optical fiber end mirror. The experimental results show that the sensitivity of temperature and depth sensing based on FBG-LPG cascade structure is about 0.0030C and 0.1%F.S. respectively, which can meet the requirements of the sea water temperature/depth observation. The reflectivity of reflection mirror is in the range from 48.8% to 72.5%, the resonant peak of FBG and LPG are reasonable and the whole spectrum are suitable for demodulation. Through research on the optical fiber XBT (FXBT), the direct measurement of deep-sea temperature/depth profile data can be obtained simultaneously, quickly and accurately. The FXBT is a new all-optical seawater temperature/depth sensor, which has important academic value and broad application prospect and is expected to replace the CXBT in the future.

  16. Precipitation and Temperature Effects on Stable Fly (Diptera: Muscidae) Population Dynamics.

    Science.gov (United States)

    Taylor, David B; Friesen, Kristina; Zhu, Jerry

    2017-06-01

    The dynamics of stable fly, Stomoxys calcitrans (L.), populations relative to temperature and precipitation were evaluated in a 13-yr study in eastern Nebraska. During the course of the study, >1.7 million stable flies were collected on an array of 25 sticky traps. A log-normal model using degree-days with a 15 °C threshold and weekly lags 0-4 for temperature and 2-7 for precipitation provided the best fit with the observed data. The relationships of temperature and precipitation to stable fly trap catches were both curvilinear, with maxima at 6.6 degree-day-15 (≈22 °C) and 7.4 mm precipitation per day, respectively. The temperature and precipitation model accounted for 72% of the variance in seasonal trap catches. Published by Oxford University Press on behalf of Entomological Society of America 2017. This work is written by US Government employees and is in the public domain in the US.

  17. Error analysis for mesospheric temperature profiling by absorptive occultation sensors

    Directory of Open Access Journals (Sweden)

    M. J. Rieder

    Full Text Available An error analysis for mesospheric profiles retrieved from absorptive occultation data has been performed, starting with realistic error assumptions as would apply to intensity data collected by available high-precision UV photodiode sensors. Propagation of statistical errors was investigated through the complete retrieval chain from measured intensity profiles to atmospheric density, pressure, and temperature profiles. We assumed unbiased errors as the occultation method is essentially self-calibrating and straight-line propagation of occulted signals as we focus on heights of 50–100 km, where refractive bending of the sensed radiation is negligible. Throughout the analysis the errors were characterized at each retrieval step by their mean profile, their covariance matrix and their probability density function (pdf. This furnishes, compared to a variance-only estimation, a much improved insight into the error propagation mechanism. We applied the procedure to a baseline analysis of the performance of a recently proposed solar UV occultation sensor (SMAS – Sun Monitor and Atmospheric Sounder and provide, using a reasonable exponential atmospheric model as background, results on error standard deviations and error correlation functions of density, pressure, and temperature profiles. Two different sensor photodiode assumptions are discussed, respectively, diamond diodes (DD with 0.03% and silicon diodes (SD with 0.1% (unattenuated intensity measurement noise at 10 Hz sampling rate. A factor-of-2 margin was applied to these noise values in order to roughly account for unmodeled cross section uncertainties. Within the entire height domain (50–100 km we find temperature to be retrieved to better than 0.3 K (DD / 1 K (SD accuracy, respectively, at 2 km height resolution. The results indicate that absorptive occultations acquired by a SMAS-type sensor could provide mesospheric profiles of fundamental variables such as temperature with

  18. Relative intensity noise of temperature-stable, energy-efficient 980 nm VCSELs

    Directory of Open Access Journals (Sweden)

    Hui Li

    2017-02-01

    Full Text Available The relative intensity noise (RIN of temperature-stable, energy-efficient oxide confined vertical-cavity surface-emitting lasers (VCSELs have been investigated. Low energy consumption data transmission is achieved by using small oxide-aperture diameter VCSELs biased at small currents. We demonstrate that energy efficiency is not in conflict with our VCSELs’ RIN characteristics. The experimental results indicate that small oxide-aperture diameter VCSELs, which are most suitable for energy-efficient, temperature-stable operation, exhibit lower laser RIN due to less mode competition inside the smaller optical cavity volume. Our energy-efficient VCSELs fulfill the RIN requirements of the 32G Fibre Channel standard.

  19. Relatively scaled ECE temperature profiles of KSTAR plasmas

    International Nuclear Information System (INIS)

    Choi, M. J.; Yun, G. S.; Park, H. K.; Jeon, Y. M.; Jeong, S. H.

    2010-01-01

    A scheme to obtain relatively scaled profiles of electron cyclotron emission (ECE) temperature directly from uncalibrated raw radiometer data is proposed and has been tested for the 2009 campaign KSTAR plasmas. The proposed method utilizes a position controlled system to move the plasma adiabatically and compares ECE radiometer channels at the same relative radial positions assuming the profile consistency during the adiabatic change. This scaling method is an alternative solution when an absolute calibration is unreliable or too time consuming. The application to the two dimensional ECE imaging data, wherein calibration is extremely difficult, may also prove to be useful.

  20. Study of density and temperature profile across the magnetic island

    International Nuclear Information System (INIS)

    Qingquan Yu; Yuping Huo

    1991-01-01

    It is well known that the magnetic island develops near the rational surface in tokamak due to the tearing mode instability. In the magnetic island region the energy and particle diffusivity are much larger than those outside the magnetic island due to the magnetic field fluctuations and the reconnection of the magnetic field lines of force. It is therefore considered previously that the plasma density and temperature profile are flattened there. In this paper it is found that the following question exists in the previous theories. That is whether the equilibrium condition ∇p=jxB/c can be satisfied if the plasma density and temperature profile are flattened across the magnetic island. Here p is plasma pressure, p=nT, n and j are plasma and current density, T is plasma temperature, B is the equilibrium magnetic field. If the plasma density and temperature profile are flattened across the magnetic island, the equilibrium condition will not be satisfied unless the plasma current density j and the equilibrium magnetic field B become much less inside the magnetic island than those in the case of no magnetic island. (author) 7 refs

  1. Temperature profile around a basaltic sill intruded into wet sediments

    Science.gov (United States)

    Baker, Leslie; Bernard, Andrew; Rember, William C.; Milazzo, Moses; Dundas, Colin M.; Abramov, Oleg; Kestay, Laszlo P.

    2015-01-01

    The transfer of heat into wet sediments from magmatic intrusions or lava flows is not well constrained from field data. Such field constraints on numerical models of heat transfer could significantly improve our understanding of water–lava interactions. We use experimentally calibrated pollen darkening to measure the temperature profile around a basaltic sill emplaced into wet lakebed sediments. It is well known that, upon heating, initially transparent palynomorphs darken progressively through golden, brown, and black shades before being destroyed; however, this approach to measuring temperature has not been applied to volcanological questions. We collected sediment samples from established Miocene fossil localities at Clarkia, Idaho. Fossils in the sediments include pollen from numerous tree and shrub species. We experimentally calibrated changes in the color of Clarkia sediment pollen and used this calibration to determine sediment temperatures around a Miocene basaltic sill emplaced in the sediments. Results indicated a flat temperature profile above and below the sill, with T > 325 °C within 1 cm of the basalt-sediment contact, near 300 °C at 1–2 cm from the contact, and ~ 250 °C at 1 m from the sill contact. This profile suggests that heat transport in the sediments was hydrothermally rather than conductively controlled. This information will be used to test numerical models of heat transfer in wet sediments on Earth and Mars.

  2. Structure-to-glass transition temperature relationships in high temperature stable condensation polyimides

    Science.gov (United States)

    Alston, W. B.; Gratz, R. F.

    1985-01-01

    The presence of a hexafluoroisopropylidene (6F) connecting group in aryl dianhydrides used to prepare aromatic condensation polyimides provides high glass transition temperature (T sub g) polyimides with excellent thermo-oxidative stability. The purpose of this study was to determine if a trifluorophenyl-ethylidene (3F) connecting group would have a similar effect on the T sub g of aromatic condensation polyimides. A new dianhydride containing the 3F connecting group was synthesized. This dianhydride and an aromatic diamine also containing the 3F connecting group were used together and in various combinations with known diamines or known dianhydrides, respectively, to prepare new 3F containing condensation polyimides. Known polyimides, including some with the 6F connecting linkage, were also prepared for comparison purposes. The new 3F containing polymers and the comparison polymers were prepared by condensation polymerization via the traditional amic-acid polymerization method in N,N-dimethylacetamide solvent. The solutions were characterized by determining their inherent viscosities and then were thermally converted into polyimide films under nitrogen atmosphere at 300 to 500 C, usually 350 C. The T sub g's of the films and resin discs were then determined by thermomechanical analysis and were correlated as a function of the final processing temperatures of the films and resin discs. The results showed that similarities existed in the T sub g's depending on the nature of the connecting linkage in the monomers used to prepare the condensation polyimides.

  3. Ensemble Postprocessing of Vertical Temperature Profiles using Standardized Anomalies

    Science.gov (United States)

    Simon, Thorsten; Schönach, David; Mayr, Georg J.

    2017-04-01

    Statistical postprocessing of output from numerical weather prediction models has long been used for bias-removal or further downscaling—mostly for single locations or (quasi-)horizontal fields. This study ventures into the postprocessing of forecasts of vertical temperature profiles. The shape of these profiles is a decisive factor for the occurrence of thunderstorms and lightning. The standardized anomalies model output statistics (SAMOS) approach is applied to vertical temperature profiles observed with radiosondes. Basic idea of SAMOS is summarized as follows: Firstly, climatologies are estimated from the observations and the numerical weather prediction (NWP) output, respectively, in order to scale both data sets. Secondly, the statistical model is built on the scaled data. Observations are taken from stations in Germany (Bergen, Lindenberg, Idar-Oberstein, Kümmersbruck) which launch radiosonde four times a day. The ECMWF-EPS provides the prediction data. It contains 50 perturbed members and 1 control member. ECMWF-reforecast data are used to estimate the model climatology and to train the statistical model. The climatologies are estimated with generalized additive models (GAM). They reveal different mean vertical profiles for different launching hours, e.g., near-surface inversions are visible at 00 UTC and 06 UTC. Moreover, annual cycles are larger closer to the surface. Scaling reduces these features. Results and verification for the period of time from September 2016 to January 2017 will be shown.

  4. Stable oxygen isotope reconstruction of ambient temperature during the collapse of a cod (Gadus morhua) fishery.

    Science.gov (United States)

    Jones, J Brin; Campana, Steven E

    2009-09-01

    Changing environmental conditions set against a backdrop of high exploitation can result in severe consequences for commercially harvested stocks. The collapse of the Eastern Scotian Shelf cod (Gadus morhua L.) off eastern Canada was primarily due to overexploitation but may have been exacerbated by a widespread temperature decline. Recent studies have called for accurate determination of ambient temperature (the actual temperature exposure history of the fish) before discarding environmental conditions as a factor in the collapse. We used the stable oxygen isotope composition of otoliths (delta18O(oto)) to reconstruct the ambient temperature history of Eastern Scotian Shelf cod from 1970 to 2000 in order to determine whether the stock experienced the temperature decline or shifted their distribution to avoid it. To correct delta18O(oto) for seawater isotope content (deltaO(w)), we generated a new meta-equation for the relationship between delta18O(w) (per mil) and salinity (S, in psu) on the Eastern Scotian Shelf: delta18O(w) = 0.539 x S - 18.790. The ambient temperature series revealed that the large-scale geographic distribution of mature cod remained constant through the cooling period, although their ambient temperature was cooler than expected in warmer periods and warmer than expected in cooler periods, indicating small-scale thermoregulatory movement. Although the mean hydrographic temperature was 4 degrees C, mature cod usually inhabited the coldest available waters (mean ambient temperature = 3 degrees C), while the juveniles usually inhabited warmer waters (mean ambient temperature = 5.5 degrees C). Length-at-age was significantly related to ambient temperature, especially in the early years of growth, and therefore declining ambient temperatures were at least partially responsible for declines in asymptotic length (up to age 8 yr). The most active thermoregulatory movement occurred during a moderate warming period; therefore extreme warming events (such

  5. Downhole temperature tool accurately measures well bore profile

    International Nuclear Information System (INIS)

    Cloud, W.B.

    1992-01-01

    This paper reports that an inexpensive temperature tool provides accurate temperatures measurements during drilling operations for better design of cement jobs, workovers, well stimulation, and well bore hydraulics. Valid temperature data during specific wellbore operations can improve initial job design, fluid testing, and slurry placement, ultimately enhancing well bore performance. This improvement applies to cement slurries, breaker activation for slurries, breaker activation for stimulation and profile control, and fluid rheological properties for all downhole operations. The temperature tool has been run standalone mounted inside drill pipe, on slick wire line and braided cable, and as a free-falltool. It has also been run piggyback on both directional surveys (slick line and free-fall) and standard logging runs. This temperature measuring system has been used extensively in field well bores to depths of 20,000 ft. The temperature tool is completely reusable in the field, ever similar to the standard directional survey tools used on may drilling rigs. The system includes a small, rugged, programmable temperature sensor, a standard body housing, various adapters for specific applications, and a personal computer (PC) interface

  6. Stable carbon isotope depth profiles and soil organic carbon dynamics in the lower Mississippi Basin

    Science.gov (United States)

    Wynn, J.G.; Harden, J.W.; Fries, T.L.

    2006-01-01

    Analysis of depth trends of 13C abundance in soil organic matter and of 13C abundance from soil-respired CO2 provides useful indications of the dynamics of the terrestrial carbon cycle and of paleoecological change. We measured depth trends of 13C abundance from cropland and control pairs of soils in the lower Mississippi Basin, as well as the 13C abundance of soil-respired CO2 produced during approximately 1-year soil incubation, to determine the role of several candidate processes on the 13C depth profile of soil organic matter. Depth profiles of 13C from uncultivated control soils show a strong relationship between the natural logarithm of soil organic carbon concentration and its isotopic composition, consistent with a model Rayleigh distillation of 13C in decomposing soil due to kinetic fractionation during decomposition. Laboratory incubations showed that initially respired CO 2 had a relatively constant 13C content, despite large differences in the 13C content of bulk soil organic matter. Initially respired CO2 was consistently 13C-depleted with respect to bulk soil and became increasingly 13C-depleted during 1-year, consistent with the hypothesis of accumulation of 13C in the products of microbial decomposition, but showing increasing decomposition of 13C-depleted stable organic components during decomposition without input of fresh biomass. We use the difference between 13C / 12C ratios (calculated as ??-values) between respired CO 2 and bulk soil organic carbon as an index of the degree of decomposition of soil, showing trends which are consistent with trends of 14C activity, and with results of a two-pooled kinetic decomposition rate model describing CO2 production data recorded during 1 year of incubation. We also observed inconsistencies with the Rayleigh distillation model in paired cropland soils and reasons for these inconsistencies are discussed. ?? 2005 Elsevier B.V. All rights reserved.

  7. Estimating atmospheric temperature profile by an airborne microwave radiometer

    Science.gov (United States)

    Zhang, Jun; Xu, Jian; Kenntner, Mareike; Schreier, Franz; Doicu, Adrian

    2017-04-01

    As the rising atmospheric issues such as climate change, air pollution, and ozone depletion have extracted extensive attraction worldwide, observing and modeling of atmospheric quantities becomes critical to our understanding of the environment. This work focuses on the performance of an airborne passive microwave radiometer called MTP (Microwave Temperature Profiler). We aim to obtain vertically distributed atmospheric temperature from intensities measured by the instrument in terms of three frequencies and ten viewing angles. A retrieval program TIRAMISU (Temperature InveRsion Algorithm for MIcrowave SoUnding) has been utilized for processing the MTP data. To solve this severely ill-posed inverse problem, an analysis of different ways of constructing the penalty term onto the Tikhonov-type objective function is conducted. This numerical analysis can help us to better understand pros and cons of these regularization methods and to investigate the measurement capabilities of MTP.

  8. Soluble and meltable hyperbranched polyborosilazanes toward high-temperature stable SiBCN ceramics.

    Science.gov (United States)

    Kong, Jie; Wang, Minjun; Zou, Jianhua; An, Linan

    2015-04-01

    High-temperature stable siliconborocarbonitride (SiBCN) ceramics produced from single-source preceramic polymers have received increased attention in the last two decades. In this contribution, soluble and meltable polyborosilazanes with hyperbranched topology (hb-PBSZ) were synthesized via a convenient solvent-free, catalyst-free and one-pot A2 + B6 strategy, an aminolysis reaction of the A2 monomer of dichloromethylsilane and the B6 monomer of tris(dichloromethylsilylethyl)borane in the presence of hexamethyldisilazane. The amine transition reaction between the intermediates of dichlorotetramethyldisilazane and tri(trimethylsilylmethylchlorosilylethyl)borane led to the formation of dendritic units of aminedialkylborons rather than trialkylborons. The cross-linked hb-PBSZ precursors exhibited a ceramic yield higher 80%. The resultant SiBCN ceramics with a boron atomic composition of 6.0-8.5% and a representative formula of Si1B(0.19)C(1.21)N(0.39)O(0.08) showed high-temperature stability and retained their amorphous structure up to 1600 °C. These hyperbranched polyborosilazanes with soluble and meltable characteristics provide a new perspective for the design of preceramic polymers possessing advantages for high-temperature stable polymer-derived ceramics with complex structures/shapes.

  9. Isolation and Screening of Thermo-Stable Cellulase Enzyme Fungal Producer at Different Temperature

    International Nuclear Information System (INIS)

    Noor Ashiqin Jamroo; Noor Azrimi Umor; Kamsani

    2015-01-01

    Thermo stable cellulase from fungi has high potential for industrial application. In this study, wild -type of fungal were isolate from different sources such as hot spring water, sea water, soft wood, rice straw and cow dung. The isolates were characterized by cultural and morphological observation. Based on morphological characteristics, the genera of all fungal cultures were identified namely Aspergillus fumigatus. The screening for thermo stable cellulase were done using 2 % carboxymethyl cellulose and congo red as an indicator at temperature 30, 37, 45 and 50 degree Celsius respectively. Out of 26 fungal isolates, only eight isolates were selected for further screening and showed the abilities to secrete cellulases by forming distinct halo zones on selective agar plate. The maximum halo zone ranging from 32 mm to 35 mm were obtained after 72 hour incubation at 50 degree Celsius by H2, SW1 and C1 isolates. As contrary other isolates showed halo zone range from 22 mm to 29 mm at same temperature. All the isolates showed the abilities to secrete cellulase enzyme at other temperature but lower when compared to 50 degree Celsius referred to the halo zone obtained. The SW1 isolates showed highest cellulolytic index which was 2.93 measured at 37 degree Celsius and 2.67 at 50 degree Celsius respectively. (author)

  10. Temperature boundary layer profiles in turbulent Rayleigh-Benard convection

    Science.gov (United States)

    Ching, Emily S. C.; Emran, Mohammad S.; Horn, Susanne; Shishkina, Olga

    2017-11-01

    Classical boundary-layer theory for steady flows cannot adequately describe the boundary layer profiles in turbulent Rayleigh-Benard convection. We have developed a thermal boundary layer equation which takes into account fluctuations in terms of an eddy thermal diffusivity. Based on Prandtl's mixing length ideas, we relate the eddy thermal diffusivity to the stream function. With this proposed relation, we can solve the thermal boundary layer equation and obtain a closed-form expression for the dimensionless mean temperature profile in terms of two independent parameters: θ(ξ) =1/b∫0b ξ [ 1 +3a3/b3(η - arctan(η)) ] - c dη , where ξ is the similarity variable and the parameters a, b, and c are related by the condition θ(∞) = 1 . With a proper choice of the parameters, our predictions of the temperature profile are in excellent agreement with the results of our direct numerical simulations for a wide range of Prandtl numbers (Pr), from Pr=0.01 to Pr=2547.9. OS, ME and SH acknowledge the financial support by the Deutsche Forschungsgemeinschaft (DFG) under Grants Sh405/4-2 (Heisenberg fellowship), Sh405/3-2 and Ho 5890/1-1, respectively.

  11. Formation of magnetite nanoparticles at low temperature: from superparamagnetic to stable single domain particles.

    Directory of Open Access Journals (Sweden)

    Jens Baumgartner

    Full Text Available The room temperature co-precipitation of ferrous and ferric iron under alkaline conditions typically yields superparamagnetic magnetite nanoparticles below a size of 20 nm. We show that at pH  =  9 this method can be tuned to grow larger particles with single stable domain magnetic (> 20-30 nm or even multi-domain behavior (> 80 nm. The crystal growth kinetics resembles surprisingly observations of magnetite crystal formation in magnetotactic bacteria. The physicochemical parameters required for mineralization in these organisms are unknown, therefore this study provides insight into which conditions could possibly prevail in the biomineralizing vesicle compartments (magnetosomes of these bacteria.

  12. Comparison of potential temperature gradient estimates from various temperature profile data sources

    Science.gov (United States)

    2017-01-22

    From July through September 2015, concurrent and collocated measurements of temperature profiles from two passive radiometers and a RADAR-RASS (Radio Acoustic Sounding System) were made at a site near the ocean just to the west of Los Angeles Interna...

  13. Late Paleocene Arctic Ocean shallow-marine temperatures from mollusc stable isotopes

    Science.gov (United States)

    Bice, Karen L.; Arthur, Michael A.; Marincovich, Louie

    1996-01-01

    Late Paleocene high-latitude (80°N) Arctic Ocean shallow-marine temperatures are estimated from molluscan δ18O time series. Sampling of individual growth increments of two specimens of the bivalve Camptochlamys alaskensis provides a high-resolution record of shell stable isotope composition. The heavy carbon isotopic values of the specimens support a late Paleocene age for the youngest marine beds of the Prince Creek Formation exposed near Ocean Point, Alaska. The oxygen isotopic composition of regional freshwater runoff is estimated from the mean δ18O value of two freshwater bivalves collected from approximately coeval fluviatile beds. Over a 30 – 34‰ range of salinity, values assumed to represent the tolerance of C. alaskensis, the mean annual shallow-marine temperature recorded by these individuals is between 11° and 22°C. These values could represent maximum estimates of the mean annual temperature because of a possible warm-month bias imposed on the average δ18O value by slowing or cessation of growth in winter months. The amplitude of the molluscan δ18O time series probably records most of the seasonality in shallow-marine temperature. The annual temperature range indicated is approximately 6°C, suggesting very moderate high-latitude marine temperature seasonality during the late Paleocene. On the basis of analogy with modern Chlamys species, C. alaskensis probably inhabited water depths of 30–50 m. The seasonal temperature range derived from δ18O is therefore likely to be damped relative to the full range of annual sea surface temperatures. High-resolution sampling of molluscan shell material across inferred growth bands represents an important proxy record of seasonality of marine and freshwater conditions applicable at any latitude. If applied to other regions and time periods, the approach used here would contribute substantially to the paleoclimate record of seasonality.

  14. Pulsed photothermal temperature profiling of agar tissue phantoms.

    Science.gov (United States)

    Milanic, Matija; Majaron, Boris; Nelson, J Stuart

    2007-11-01

    We determine experimentally the accuracy of pulsed photothermal radiometric (PPTR) temperature depth profiling in water-based samples. We use custom tissue phantoms composed of agar gel layers separated by very thin absorbing layers. Two configurations of the acquisition system are compared, one using the customary spectral band of the InSb radiation detector (3.0-5.5 microm) and the other with a spectrally narrowed acquisition band (4.5-5.5 microm). The laser-induced temperature depth profiles are reconstructed from measured radiometric signals using a custom minimization algorithm. The results correlate very well with phantom geometry as determined by optical coherence tomography (OCT) and histology in all evaluated samples. Determination of the absorbing layer depth shows good repeatability with spatial resolution decreasing with depth. Spectral filtering improves the accuracy and resolution, especially for shallow absorption layers (~120 microm) and more complex structures (e.g., with two absorbing layers). The average full width at half maximum (FWHM) of the temperature peaks equals 23% of the layer depth.

  15. A review of some recent studies on the stable isotope profiling of methylamphetamine: Is it a useful adjunct to conventional chemical profiling?

    Science.gov (United States)

    Collins, Michael; Salouros, Helen

    2015-01-01

    This paper reviews a body of work published by the authors over a number of years aimed at providing a complementary "signature" to conventional chemical profiling of methylamphetamine. The work, beginning in 2009, was undertaken because of the changing nature of clandestine methylamphetamine manufacture which has seen a dramatic rise in production and a major shift to a higher quality product. As manufacturing methods changed and methylamphetamine purity increased some conventional drug profiling techniques became less useful as an intelligence tool. For instance, the value of the organic impurity profile, a mainstay of conventional profiling, decreases as there are fewer impurities present in seized samples. However, whilst many seizures may contain less conventional chemical intelligence another property of the methylamphetamine molecule is always available, i.e. the light element stable isotope ratios. The stable isotope ratios of carbon, hydrogen and nitrogen are an integral part of the methylamphetamine molecule itself. This review describes previous work by the authors and by researchers in other national laboratories to investigate and implement the use of stable isotope ratios as an everyday methylamphetamine profiling tool. It also looks at how powerful this technique can be when used to compare samples from different seizures. Crown Copyright © 2014. Published by Elsevier Ireland Ltd. All rights reserved.

  16. Microwave radiometer to retrieve temperature profiles from the surface to the stratopause

    Directory of Open Access Journals (Sweden)

    O. Stähli

    2013-09-01

    Full Text Available TEMPERA (TEMPERature RAdiometer is a new ground-based radiometer which measures in a frequency range from 51–57 GHz radiation emitted by the atmosphere. With this instrument it is possible to measure temperature profiles from ground to about 50 km. This is the first ground-based instrument with the capability to retrieve temperature profiles simultaneously for the troposphere and stratosphere. The measurement is done with a filterbank in combination with a digital fast Fourier transform spectrometer. A hot load and a noise diode are used as stable calibration sources. The optics consist of an off-axis parabolic mirror to collect the sky radiation. Due to the Zeeman effect on the emission lines used, the maximum height for the temperature retrieval is about 50 km. The effect is apparent in the measured spectra. The performance of TEMPERA is validated by comparison with nearby radiosonde and satellite data from the Microwave Limb Sounder on the Aura satellite. In this paper we present the design and measurement method of the instrument followed by a description of the retrieval method, together with a validation of TEMPERA data over its first year, 2012.

  17. Exploration of ion temperature profile measurements at JET using the upgraded neutron profile monitor

    International Nuclear Information System (INIS)

    Marocco, D.; Esposito, B.; Riva, M.

    2012-01-01

    The neutron profile monitor (NPM), routinely used at the Joint European Torus for neutron emissivity profile measurements, consists of two fan-shaped arrays of collimators and each line of sight (LOS) is equipped with a NE213 liquid organic scintillator for simultaneous measurements of the 2.5 MeV and 14 MeV neutrons. A digital system developed in ENEA has replaced the analog acquisition electronics and now enables the NPM to perform spatially resolved neutron spectrometry by providing neutron pulse height spectra (PHS) for each LOS. However, the NPM was not originally designed as a spectrometer and, therefore, lacks several key features, such as detailed measurements of the detector response functions and the presence of detector stability monitors. We present a proof of principle of ion temperature profile measurements derived from the NPM PHS in high plasma current discharges using simulated detector response functions.

  18. Room temperature stable CO x -free H2production from methanol with magnesium oxide nanophotocatalysts.

    Science.gov (United States)

    Liu, Zhengqing; Yin, Zongyou; Cox, Casandra; Bosman, Michel; Qian, Xiaofeng; Li, Na; Zhao, Hongyang; Du, Yaping; Li, Ju; Nocera, Daniel G

    2016-09-01

    Methanol, which contains 12.6 weight percent hydrogen, is a good hydrogen storage medium because it is a liquid at room temperature. However, by releasing the hydrogen, undesirable CO and/or CO 2 byproducts are formed during catalytic fuel reforming. We show that alkaline earth metal oxides, in our case MgO nanocrystals, exhibit stable photocatalytic activity for CO/CO 2 -free H 2 production from liquid methanol at room temperature. The performance of MgO nanocrystals toward methanol dehydrogenation increases with time and approaches ~320 μmol g -1 hour -1 after a 2-day photocatalytic reaction. The CO x -free H 2 production is attributed to methanol photodecomposition to formaldehyde, photocatalyzed by surface electronic states of unique monodispersed, porous MgO nanocrystals, which were synthesized with a novel facile colloidal chemical strategy. An oxygen plasma treatment allows for the removal of organic surfactants, producing MgO nanocrystals that are well dispersible in methanol.

  19. Room temperature bioproduction, isolation and anti-microbial properties of stable elemental copper nanoparticles.

    Science.gov (United States)

    Pantidos, Nikolaos; Edmundson, Matthew C; Horsfall, Louise

    2018-01-25

    In nanoparticle production there are a number of important considerations that must be made. Producing nanoparticles of uniform size and shape is vital, but no less important is ensuring the production process is as efficient as possible in time, cost and energy. Traditional chemical and physical methods of nanoparticle production often involve high temperatures and pressures, as well as the use of toxic substrates; in contrast the bioproduction of nanoparticles is greener and requires a smaller input of energy resources. Here we outline a method for the straightforward bioproduction of stable, uniform elemental (zero-valent) copper nanoparticles at room temperature, and demonstrate how their size and shape can be modified by subsequent pH manipulation. We also highlight a potential application for these biogenic copper nanoparticles by demonstrating their potential to inhibit bacterial growth. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

  20. Adaptive temperature profile control of a multizone crystal growth furnace

    Science.gov (United States)

    Batur, C.; Sharpless, R. B.; Duval, W. M. B.; Rosenthal, B. N.

    1991-01-01

    An intelligent measurement system is described which is used to assess the shape of a crystal while it is growing inside a multizone transparent furnace. A color video imaging system observes the crystal in real time, and determines the position and the shape of the interface. This information is used to evaluate the crystal growth rate, and to analyze the effects of translational velocity and temperature profiles on the shape of the interface. Creation of this knowledge base is the first step to incorporate image processing into furnace control.

  1. A model for quantification of temperature profiles via germination times

    DEFF Research Database (Denmark)

    Pipper, Christian Bressen; Adolf, Verena Isabelle; Jacobsen, Sven-Erik

    2013-01-01

    Current methodology to quantify temperature characteristics in germination of seeds is predominantly based on analysis of the time to reach a given germination fraction, that is, the quantiles in the distribution of the germination time of a seed. In practice interpolation between observed...... germination fractions at given monitoring times is used to obtain the time to reach a given germination fraction. As a consequence the obtained value will be highly dependent on the actual monitoring scheme used in the experiment. In this paper a link between currently used quantile models for the germination...... time and a specific type of accelerated failure time models is provided. As a consequence the observed number of germinated seeds at given monitoring times may be analysed directly by a grouped time-to-event model from which characteristics of the temperature profile may be identified and estimated...

  2. Temperature profiles of low-temperature alloy irradiated by pulsed ion beams

    International Nuclear Information System (INIS)

    Zhang, Guoliang; Wang, Boyu; Shi, Lei; Tan, Xiaohua; Xiang, Wei

    2013-01-01

    While alloy materials is irradiated by the high-intensity pulsed ion beams (HIPIB), the temperature distributions surrounding the primary heated regions used numerical analysis has been studied extensively over the past few years. Compared with the temperature distributions induced by HIPIB, few information is known about the temperature distributions on alloy materials used in practice as it is irradiated by the pulsed ion beams which possess characteristics of lower energy density and longer pulse width. The main reason is that the interaction between the alloy materials and the pulsed ion beams is only a few microseconds. It is difficult to detect temperature changes on alloy materials used in practice through traditional test. Ablation, melting, defects of microstructure on alloy materials are always used to validate the results of numerical analysis about the temperature distributions indirectly. In order to evaluate the temperature distributions directly, the dynamic thermal-dependent temperature behavior of the low-temperature alloy irradiated by the pulsed ion beams is investigated by experimental observation and finite element method (FEM) simulation in this paper. The temperature profiles generated from the interaction of μs-size between the alloy materials and the pulsed ion beams are evaluated by coupling characteristics of the low melting point and the pulsed ion beams. The FEM simulation results of the maximum temperature agree well with the experimental results on the surface of the low-temperature alloy. Results gained show that the maximum temperature on the surface of the low-temperature alloy irradiated by the pulsed ion beams can be applied to deduce the maximum temperature on alloy materials used in practice

  3. 40 CFR 86.1229-85 - Dynamometer load determination and fuel temperature profile.

    Science.gov (United States)

    2010-07-01

    ... fuel temperature profile. 86.1229-85 Section 86.1229-85 Protection of Environment ENVIRONMENTAL... load determination and fuel temperature profile. (a) Flywheels, electrical or other means of simulating... vehicle must have a fuel temperature profile. The following procedure is used to generate the fuel...

  4. P{sup 2}IMS depth profile analysis of high temperature boron oxynitride dielectric films

    Energy Technology Data Exchange (ETDEWEB)

    Badi, N., E-mail: nbadi@uh.edu [Center for Advanced Materials (CAM), University of Houston, Houston, TX 77204-5004 (United States); Physics Department, University of Houston, Houston, TX 77204-5005 (United States); Vijayaraghavan, S. [Center for Advanced Materials (CAM), University of Houston, Houston, TX 77204-5004 (United States); Benqaoula, A. [Physics Department, University of Houston, Houston, TX 77204-5005 (United States); Tempez, A.; Tauziède, C.; Chapon, P. [Horiba Jobin Yvon, Longjumeau, F-91160 Paris (France)

    2014-02-15

    Existing silicon oxynitride (SiON) dielectric can only provide a very near term solution for the metal oxide semiconductor technology. The emerging high-k dielectric materials have a limited thermal stability and are prone to electrical behavior degradation which is associated with unwanted chemical reactions with silicon (Si). We investigated here applicability of amorphous boron oxynitride (BON) thin films as an emerging dielectric for high temperature capacitors. BON samples of thickness varying from 200 nm down to 10 nm were deposited in a high vacuum reactor using ion source assisted physical vapor deposition (PVD) technique. Plasma profiling ion mass spectrometry (P{sup 2}IMS) was utilized to specifically determine the interface quality and best capacitor performance as a function of growth temperatures of a graded sample with alternate layers of deposited titanium (Ti) and BON layers on Si. P{sup 2}IMS depth profiling of these layers were also performed to evaluate the stability of the dielectric layers and their efficacy against B dopant diffusion simulating processes occurring in activated polySi-based devices. For this purpose, BON layers were deposited on boron-isotope 10 (B{sup 10}) implanted Si substrates and subsequently annealed at high temperatures up to 1050 °C for about 10 s. Results comparing inter-diffusion of B{sup 10} intensities at the interfaces of BON–Si and SiON–Si samples suggest suitability of BON as barrier layers against boron diffusion at high temperature. Stable Ti/BON/Ti capacitor behavior was achieved at optimum growth temperature of 600 °C of the BON dielectric layer. Capacitance change with frequency (10 kHz to 2 MHz) and temperature up to 400 °C is about 1% and 10%, respectively.

  5. Temperature profiles of different cooling methods in porcine pancreas procurement.

    Science.gov (United States)

    Weegman, Bradley P; Suszynski, Thomas M; Scott, William E; Ferrer Fábrega, Joana; Avgoustiniatos, Efstathios S; Anazawa, Takayuki; O'Brien, Timothy D; Rizzari, Michael D; Karatzas, Theodore; Jie, Tun; Sutherland, David E R; Hering, Bernhard J; Papas, Klearchos K

    2014-01-01

    Porcine islet xenotransplantation is a promising alternative to human islet allotransplantation. Porcine pancreas cooling needs to be optimized to reduce the warm ischemia time (WIT) following donation after cardiac death, which is associated with poorer islet isolation outcomes. This study examines the effect of four different cooling Methods on core porcine pancreas temperature (n = 24) and histopathology (n = 16). All Methods involved surface cooling with crushed ice and chilled irrigation. Method A, which is the standard for porcine pancreas procurement, used only surface cooling. Method B involved an intravascular flush with cold solution through the pancreas arterial system. Method C involved an intraductal infusion with cold solution through the major pancreatic duct, and Method D combined all three cooling Methods. Surface cooling alone (Method A) gradually decreased core pancreas temperature to procurement, but incorporating an intraductal infusion (Method C) rapidly reduced core temperature 15-20 °C within the first 2 min of cooling. Combining all methods (Method D) was the most effective at rapidly reducing temperature and providing sustained cooling throughout the duration of procurement, although the recorded WIT was not different between Methods (P = 0.36). Histological scores were different between the cooling Methods (P = 0.02) and the worst with Method A. There were differences in histological scores between Methods A and C (P = 0.02) and Methods A and D (P = 0.02), but not between Methods C and D (P = 0.95), which may highlight the importance of early cooling using an intraductal infusion. In conclusion, surface cooling alone cannot rapidly cool large (porcine or human) pancreata. Additional cooling with an intravascular flush and intraductal infusion results in improved core porcine pancreas temperature profiles during procurement and histopathology scores. These data may also have implications on human pancreas procurement as use of an

  6. STABLE HIGH CONDUCTIVITY BILAYERED ELECTROLYTES FOR LOW TEMPERATURE SOLID OXIDE FUEL CELLS

    Energy Technology Data Exchange (ETDEWEB)

    Eric D. Wachsman; Keith L. Duncan

    2001-09-30

    Solid oxide fuel cells (SOFCs) are the future of energy production in America. They offer great promise as a clean and efficient process for directly converting chemical energy to electricity while providing significant environmental benefits (they produce negligible hydrocarbons, CO, or NO{sub x} and, as a result of their high efficiency, produce about one-third less CO{sub 2} per kilowatt hour than internal combustion engines). Unfortunately, the current SOFC technology, based on a stabilized zirconia electrolyte, must operate in the region of 1000 C to avoid unacceptably high ohmic losses. These high temperatures demand (a) specialized (expensive) materials for the fuel cell interconnects and insulation, (b) time to heat up to the operating temperature and (c) energy input to arrive at the operating temperature. Therefore, if fuel cells could be designed to give a reasonable power output at low to intermediate1 temperatures tremendous benefits may be accrued. At low temperatures, in particular, it becomes feasible to use ferritic steel for interconnects instead of expensive and brittle ceramic materials such as those based on LaCrO{sub 3}. In addition, sealing the fuel cell becomes easier and more reliable; rapid start-up is facilitated; thermal stresses (e.g., those caused by thermal expansion mismatches) are reduced; radiative losses ({approx}T{sup 4}) become minimal; electrode sintering becomes negligible and (due to a smaller thermodynamic penalty) the SOFC operating cycle (heating from ambient) would be more efficient. Combined, all these improvements further result in reduced initial and operating costs. The problem is, at lower temperatures the conductivity of the conventional stabilized zirconia electrolyte decreases to the point where it cannot supply electrical current efficiently to an external load. The primary objectives of the proposed research are to develop a stable high conductivity (> 0.05 S cm{sup -1} at {le} 550 C) electrolyte for lower

  7. Physiochemical and environmental stable isotope profile of marine coastal water, Pakistan

    International Nuclear Information System (INIS)

    Mashiatullah, A.; Qureshi, R.M.; Javed, T.; Fazil, M.; Latif, Z.; Ahmad, N.

    2005-01-01

    Physiochemical and environmental stable isotope (delta /sup 13/C, delta /sup 18/O delta /sup 2/H, delta /sup 34/S) analysis of seawater samples collected from selected locations off Pakistan. Coast was performed to assess pollution scenario during 2002. Objective of the study was to establish a baseline data profile of Pakistan coastal waters. Coastal location includes: Indus Delta, Karachi Harbour, Southeast Coast Karachi, Northwest Coast Karachi, Sonmiani, Ormara. Pasni, Gwadar and Jiwani. In-situ physiochemical parameters such as: pH, electrical conductivity (E.C), salinity, turbidity and dissolved oxygen (DO) were performed with portable meters. Stable isotope of oxygen, hydrogen, carbon and sulfur was performed on GD -150 modified Mass Spectrometer. Values of delta /sup 18/O along the Sindh Coast (Indus Delta, Karachi Harbour High Tide, Karachi Harbour Low Tide, North West Coast South East Coast, Gadani), lie in range of -6.3 to -2.4 , -0.17 to -0.2, -0.13 to + 1.16, + 0.65 to + 1.25, + 0.88 to +0.93, and 1.14 %. SMOW respectively. The values of delta /sup 18/O along Baluchistan Coast (Sonmiani, Ormara, Pasni, Gwadar, and Jiwani) lie in the range of 0.74 to 1.08,0.77 to 0.82, 0.96 to + 1.07,0.38 to 1.23, and 0.45 to 0.83 % SMOW respectively. Values of delta /sup 13/ C of total dissolved inorganic carbon (TDIC) along Sindh Coast lie in the range of -2.7 to 0.55, -7.0 to -2.14, -11.48 to -2.98, -1.26 to 2.12, -2.91 to -0.56, and -1.31 to -0.28 % V- PDB. Values of delta /sup 13/ C of total dissolved inorganic carbon (TDIC) off Baluchistan Coast lie in the range of - 2.65 to -0.68, -8.5 to 0.07, -1.1 to 0.01, -1.3 to 0.47 and -5.2 to 0 % V-PDB respectively. Significantly depleted delta /sup 13/C (TDIC) values observed in water samples collected off Karachi coast, Indus Delta and Armor Coast indicate pollution inputs from industrial and domestic waste drains into shallow marine environment off these coasts. Carbon Isotope data shows that the Gwadar and Pasni are

  8. Partitioning of Evapotranspiration Using a Stable Water Isotope Technique in a High Temperature Agricultural Production System

    Science.gov (United States)

    Lu, X.; Liang, L.; Wang, L.; Jenerette, D.; Grantz, D. A.

    2015-12-01

    Agricultural production in the hot and arid low desert systems of southern California relies heavily on irrigation. A better understanding of how much and to what extent the irrigation water is transpired by crops relative to being lost through evaporation will contribute to better management of increasingly limited agricultural water resources. In this study, we examined the evapotranspiration (ET) partitioning over a field of forage sorghum (S. bicolor) during a growing season with several irrigation cycles. In several field campaigns we used continuous measurements of near-surface variations in the stable isotopic composition of water vapor (δ2H). We employed custom built transparent chambers coupled with a laser-based isotope analyzer and used Keeling plot and mass balance methods for surface flux partitioning. The preliminary results show that δT is more enriched than δE in the early growing season, and becomes less enriched than δE later in the season as canopy cover increases. There is an increase in the contribution of transpiration to ET as (1) leaf area index increases, and (2) as soil surface moisture declines. These results are consistent with theory, and extend these measurements to an environment that experiences extreme soil surface temperatures. The data further support the use of chamber based methods with stable isotopic analysis for characterization of ET partitioning in challenging field environments.

  9. High Temperature Stable Separator for Lithium Batteries Based on SiO₂ and Hydroxypropyl Guar Gum.

    Science.gov (United States)

    Carvalho, Diogo Vieira; Loeffler, Nicholas; Kim, Guk-Tae; Passerini, Stefano

    2015-10-23

    A novel membrane based on silicon dioxide (SiO₂) and hydroxypropyl guar gum (HPG) as binder is presented and tested as a separator for lithium-ion batteries. The separator is made with renewable and low cost materials and an environmentally friendly manufacturing processing using only water as solvent. The separator offers superior wettability and high electrolyte uptake due to the optimized porosity and the good affinity of SiO₂ and guar gum microstructure towards organic liquid electrolytes. Additionally, the separator shows high thermal stability and no dimensional-shrinkage at high temperatures due to the use of the ceramic filler and the thermally stable natural polymer. The electrochemical tests show the good electrochemical stability of the separator in a wide range of potential, as well as its outstanding cycle performance.

  10. Retrieval of temperature profiles from Martian infrared spectra

    Science.gov (United States)

    Mcmillan, W. Wallace; Pearl, John C.; Conrath, Barney J.

    1993-01-01

    In theory, a thermal emission spectrum of Mars (220-1600 cm(exp -1)) contains a wealth of information about the composition and thermal structure of the atmosphere and surface. However, in practice, the ability to retrieve quantitative information from the spectrum is limited by a number of factors including (1) the ill-posed nature of the spectral inversion problem and the resulting nonuniqueness of all solutions; (2) assumptions built into any spectral inversion program; (3) uncertainties in surface pressure, temperature, and emissivity; and (4) uncertainties in the optical properties of atmospheric aerosols. Below, factors (1) and (2) are discussed as fundamental limitations on temperature retrievals from Mariner 9 Infrared Interferometer Spectrometer (IRIS) spectra. In preparation for the Mars Observer mission and the return of tens of thousands of infrared spectra per day from the Thermal Emission Spectrometer (TES), we have developed a fast inversion algorithm to retrieve temperature structure and aerosol opacity from the infrared spectra. The derived atmospheric models will be used to provide the atmospheric contribution to the TES spectra, so that the thermal emission spectra of the underlying surface can be determined for making mineralogical identifications. As a test of our algorithm, we are undertaking a systematic analysis of the entire Mariner 9 Infrared Interferometric Spectrometer (IRIS) dataset of 21,000 plus spectra. While portions of the IRIS dataset have been previously analyzed, the lack of a speedy and robust algorithm to invert the IRIS spectra to retrieve temperature profiles and aerosol opacities has been a major impediment to a truly comprehensive analysis.

  11. Recoil Induced Room Temperature Stable Frenkel Pairs in a-Hafnium Upon Thermal Neutron Capture

    Science.gov (United States)

    Butz, Tilman; Das, Satyendra K.; Dey, Chandi C.; Ghoshal, Shamik

    2013-11-01

    Ultrapure hafnium metal (110 ppm zirconium) was neutron activated with a thermal neutron flux of 6:6 · 1012 cm-2s-1 in order to obtain 181Hf for subsequent time differential perturbed angular correlation (TDPAC) experiments using the nuclear probe 181Hf(β-) 181Ta. Apart from the expected nuclear quadrupole interaction (NQI) signal for a hexagonal close-packed (hcp) metal, three further discrete NQIs were observed with a few percent fraction each. The TDPAC spectra were recorded for up to 11 half lives with extreme statistical accuracy. The fitted parameters vary slightly within the temperature range between 248 K and 373 K. The signals corresponding to the three additional sites completely disappear after `annealing' at 453 K for one minute. Based on the symmetry of the additional NQIs and their temperature dependencies, they are tentatively attributed to Frenkel pairs produced by recoil due to the emission of a prompt 5:694 MeV -ray following thermal neutron capture and reported by the nuclear probe in three different positions. These Frenkel pairs are stable up to at least 373 K.

  12. High-Temperature Stable Anatase Titanium Oxide Nanofibers for Lithium-Ion Battery Anodes.

    Science.gov (United States)

    Lee, Sangkyu; Eom, Wonsik; Park, Hun; Han, Tae Hee

    2017-08-02

    Control of the crystal structure of electrochemically active materials is an important approach to fabricating high-performance electrodes for lithium-ion batteries (LIBs). Here, we report a methodology for controlling the crystal structure of TiO 2 nanofibers by adding aluminum isopropoxide to a common sol-gel precursor solution utilized to create TiO 2 nanofibers. The introduction of aluminum cations impedes the phase transformation of electrospun TiO 2 nanofibers from the anatase to the rutile phase, which inevitably occurs in the typical annealing process utilized for the formation of TiO 2 crystals. As a result, high-temperature stable anatase TiO 2 nanofibers were created in which the crystal structure was well-maintained even at high annealing temperatures of up to 700 °C. Finally, the resulting anatase TiO 2 nanofibers were utilized to prepare LIB anodes, and their electrochemical performance was compared to pristine TiO 2 nanofibers that contain both anatase and rutile phases. Compared to the electrode prepared with pristine TiO 2 nanofibers, the electrode prepared with anatase TiO 2 nanofibers exhibited excellent electrochemical performances such as an initial Coulombic efficiency of 83.9%, a capacity retention of 89.5% after 100 cycles, and a rate capability of 48.5% at a current density of 10 C (1 C = 200 mA g -1 ).

  13. Room temperature stable COx-free H2 production from methanol with magnesium oxide nanophotocatalysts

    Science.gov (United States)

    Liu, Zhengqing; Yin, Zongyou; Cox, Casandra; Bosman, Michel; Qian, Xiaofeng; Li, Na; Zhao, Hongyang; Du, Yaping; Li, Ju; Nocera, Daniel G.

    2016-01-01

    Methanol, which contains 12.6 weight percent hydrogen, is a good hydrogen storage medium because it is a liquid at room temperature. However, by releasing the hydrogen, undesirable CO and/or CO2 byproducts are formed during catalytic fuel reforming. We show that alkaline earth metal oxides, in our case MgO nanocrystals, exhibit stable photocatalytic activity for CO/CO2-free H2 production from liquid methanol at room temperature. The performance of MgO nanocrystals toward methanol dehydrogenation increases with time and approaches ~320 μmol g−1 hour−1 after a 2-day photocatalytic reaction. The COx-free H2 production is attributed to methanol photodecomposition to formaldehyde, photocatalyzed by surface electronic states of unique monodispersed, porous MgO nanocrystals, which were synthesized with a novel facile colloidal chemical strategy. An oxygen plasma treatment allows for the removal of organic surfactants, producing MgO nanocrystals that are well dispersible in methanol. PMID:28508036

  14. Thermal conductivity and temperature profiles in carbon electrodes for supercapacitors

    Science.gov (United States)

    Burheim, Odne S.; Aslan, Mesut; Atchison, Jennifer S.; Presser, Volker

    2014-01-01

    The thermal conductivity of supercapacitor film electrodes composed of activated carbon (AC), AC with 15 mass% multi-walled carbon nanotubes (MWCNTs), AC with 15 mass% onion-like carbon (OLC), and only OLC, all mixed with polymer binder (polytetrafluoroethylene), has been measured. This was done for dry electrodes and after the electrodes have been saturated with an organic electrolyte (1 M tetraethylammonium-tetrafluoroborate in acetonitrile, TEA-BF4). The thermal conductivity data was implemented in a simple model of generation and transport of heat in a cylindrical cell supercapacitor systems. Dry electrodes showed a thermal conductivity in the range of 0.09-0.19 W K-1 m-1 and the electrodes soaked with an organic electrolyte yielded values for the thermal conductivity between 0.42 and 0.47 W K-1 m-1. It was seen that the values related strongly to the porosity of the carbon electrode materials. Modeling of the internal temperature profiles of a supercapacitor under conditions corresponding to extreme cycling demonstrated that only a moderate temperature gradient of several degrees Celsius can be expected and which depends on the ohmic resistance of the cell as well as the wetting of the electrode materials.

  15. Stable BC 2N nanostructures: low-temperature production of segregated C/BN layered materials

    Science.gov (United States)

    Kohler-Redlich, Ph.; Terrones, M.; Manteca-Diego, C.; Hsu, W. K.; Terrones, H.; Rühle, M.; Kroto, H. W.; Walton, D. R. M.

    1999-09-01

    Stable filaments of nanometer dimensions with overall chemical stoichiometry close to BC 2N were generated by pyrolysis of CH 3CN·BCl 3 over Co at 1000°C and, for the first time, their structures were investigated, at the nanometer level, using high spatial resolution electron energy-loss spectroscopy. Concentration profiles, along and across the filaments, revealed that B, C and N are not homogeneously distributed within the nanostructures but are separated into pure C and BN domains. Interestingly, pure h-BN layers are always sandwiched between graphite-like shells. A two-stage growth process is proposed involving: (a) initial extrusion of a pure carbon filament from the catalytic particle, followed by (b) subsequent thickening of the BN and C layers precipitated from the gas phase. This pyrolytic technique provides an alternative and efficient route to segregated BN/C nanomaterials, which may prove useful as robust nanocomposites and semiconductor nanodevices with enhanced resistance towards oxidation.

  16. The Role of Priming in the Development of Stable and Radioactive Carbon Isotope Profiles of Soil Organic Matter

    Science.gov (United States)

    Serach, L.; Breecker, D.

    2017-12-01

    The stability of soil carbon (C) is one of the largest sources of uncertainty in global C cycle models and is central to identifying potential feedbacks to a warming climate. The role that more stable soil organic matter (SOM) pools could have in these feedbacks is highly uncertain. Stable C isotope (δ13C) and radiocarbon (14C) SOM profiles are used to understand the processes involved in soil C stabilization. In this study, we use a 1-dimensional, 3 pool soil C model to simulate the development of SOM δ13C and 14C profiles in a well-drained forest soil. Under the simplest model scenario where decomposition rate constants for each SOM pool remain fixed, model runs exhibit a buildup of slowly degrading C in the shallow subsurface (0-5cm) where fresh, labile C typically dominates in natural soils. Additionally, magnitudes of trends in SOM δ13C and 14C profiles were inconsistent with those observed in natural profiles, suggesting a deficiency in this version of the model. We hypothesize that the observed disparity between modeled and natural profiles is due to the absence of priming in the model. Priming effects presume a change in decomposition rate constants for recalcitrant C pools upon the addition of labile C to the soil. As such, priming effects were simulated in the model by making decomposition rate constants a function of labile C input (e.g., root C and leaf litter). The incorporation of priming into the model yields larger, more realistic shifts in SOM δ13C profiles and trends in 14C profiles that vary based on the sensitivity of recalcitrant pools to labile C addition. So far, the results from this study support the hypothesis that SOM δ13C and 14C profiles cannot be explained without priming. These results highlight the importance of priming to our understanding of the persistence of stable C in the soil and our ability to use SOM δ13C and 14C trends as a means to quantify C stability.

  17. Room Temperature Stable PspA-Based Nanovaccine Induces Protective Immunity

    Directory of Open Access Journals (Sweden)

    Danielle A. Wagner-Muñiz

    2018-03-01

    Full Text Available Streptococcus pneumoniae is a major causative agent of pneumonia, a debilitating disease particularly in young and elderly populations, and is the leading worldwide cause of death in children under the age of five. While there are existing vaccines against S. pneumoniae, none are protective across all serotypes. Pneumococcal surface protein A (PspA, a key virulence factor of S. pneumoniae, is an antigen that may be incorporated into future vaccines to address the immunological challenges presented by the diversity of capsular antigens. PspA has been shown to be immunogenic and capable of initiating a humoral immune response that is reactive across approximately 94% of pneumococcal strains. Biodegradable polyanhydrides have been studied as a nanoparticle-based vaccine (i.e., nanovaccine platform to stabilize labile proteins, to provide adjuvanticity, and enhance patient compliance by providing protective immunity in a single dose. In this study, we designed a room temperature stable PspA-based polyanhydride nanovaccine that eliminated the need for a free protein component (i.e., 100% encapsulated within the nanoparticles. Mice were immunized once with the lead nanovaccine and upon challenge, presented significantly higher survival rates than animals immunized with soluble protein alone, even with a 25-fold reduction in protein dose. This lead nanovaccine formulation performed similarly to protein adjuvanted with Alum, however, with much less tissue reactogenicity at the site of immunization. By eliminating the free PspA from the nanovaccine formulation, the lead nanovaccine was efficacious after being stored dry for 60 days at room temperature, breaking the need for maintaining the cold chain. Altogether, this study demonstrated that a single dose PspA-based nanovaccine against S. pneumoniae induced protective immunity and provided thermal stability when stored at room temperature for at least 60 days.

  18. Numerical study of effects of atmosphere temperature profile on wildfire behavior

    Science.gov (United States)

    Chunmei Xia; M. Yousuff Hussaini; Philip Cunningham; Rodman R. Linn; Scott L. Goodrick

    2003-01-01

    The vertical temperature profile and hence the stability in the atmosphere near the ground vanes significantly between day and night. Typically, the potential temperature at the surface is higher than that above the ground during the day and lower than that above the ground during the night. Such differences in the vertical temperature profile might act to accelerate...

  19. Frequency dependence of the temperature profile of a copper vapor laser

    International Nuclear Information System (INIS)

    Behrouzinia, S; Khorasani, K

    2016-01-01

    The gas temperature of a copper vapor laser was measured by a semi-experimental method. Moreover the temperature profiles were obtained at various frequencies. It was shown that the temperature profile has most uniformity among the cross section of the laser tube at optimum frequency. (paper)

  20. The calcineurin activity profiles of cyclosporin and tacrolimus are different in stable renal transplant patients

    DEFF Research Database (Denmark)

    Koefoed-Nielsen, PB; Karamperis, N; Hojskov, C

    2006-01-01

    Cyclosporin and tacrolimus remain the cornerstone immunosuppressive drugs in organ transplantation. Dosing and monitoring these drugs is based on pharmacokinetic protocols, but measuring a pharmacodynamic parameter, calcineurin phosphatase (CaN) activity, could be a valuable supplement...... in determining optimal doses. Forty stable renal transplant patients were investigated three times in a 6-month period. Blood samples were drawn at 0, 1, 2, 3 and 4 h after oral intake of tacrolimus (FK) or cyclosporin at days 1 and 180. At day 90, one blood sample at trough level (FK) or C2 level (cyclosporin A...... significantly different effects on calcineurin activity in renal transplant patients with stable, well-functioning grafts and that tacrolimus-treated patients can maintain good, stable graft function with minimal CaN inhibition....

  1. Ion temperature profiles along a hydrogen diagnostic beam in a TORE SUPRA tokamak plasma

    International Nuclear Information System (INIS)

    Romannikov, A.; Petrov, Yu.; Platts, P.; Khess, V.; Khutter, T.; Farzhon, Zh.; Moro, F.

    2002-01-01

    By means of corpuscular diagnostics one studies temperature of ions along a diagnostic hydrogen beam. Paper presents comparison of temperature of plasma (deuterium) basic ions measures by means of the active corpuscular diagnostics with temperature of C + carbon ions along a beam. One studies behavior peculiarities of T i ion temperature profiles for TORE-SUPRA different modes, such as: formation of plane and even hollow T i profiles for ohmic modes, variation of T i profiles under operation of an ergodic diverter, difference of temperature of basic ions measured by means of the active corpuscular diagnostics from C +5 temperature. Paper offers clear explanation of these peculiarities [ru

  2. The Mathematical Representation of Wind Speed and Temperature Profiles in the Unstable Atmospheric Surface Layer

    DEFF Research Database (Denmark)

    Paulson, C.A.

    1970-01-01

    Analytical expressions which specify non-dimensionalized wind speed and potential temperature gradients as functions of stability are integrated. The integrated equations are tested against Swinhank's wind and temperature profiles measured at Kerang, Australia. It is found that a representation...... suggested independently by Businger and by Dyer gives the best fit to temperature profiles and describes the wind profiles equally as well as a relation suggested by Panofsky et al....

  3. Influence of forest disturbance on stable nitrogen isotope ratios in soil and vegetation profiles

    Science.gov (United States)

    Jennifer D. Knoepp; Scott R. Taylor; Lindsay R. Boring; Chelcy F. Miniat

    2015-01-01

    Soil and plant stable nitrogen isotope ratios (15 N) are influenced by atmospheric nitrogen (N) inputs and processes that regulate organic matter (OM) transformation and N cycling. The resulting 15N patterns may be useful for discerning ecosystem differences in N cycling. We studied two ecosystems; longleaf pine wiregrass (...

  4. Influence of absorbed pump profile on the temperature distribution ...

    Indian Academy of Sciences (India)

    2017-01-20

    -pumped laser rod is extracted. This model can be used for side-pumped laser rods whose absorbed pump profile is a Gaussian profile. Then, it is validated by numerical results which exhibit a good agreement with the ...

  5. Interactive Matching between the Temperature Profile and Secondary Reactions of Oil Shale Pyrolysis

    DEFF Research Database (Denmark)

    Zhang, Yu; Han, Zhennan; Wu, Hao

    2016-01-01

    This article investigates the effect of the reactor temperature profile on the distribution and characteristics of the products from fixed-bed pyrolysis of oil shale. Experiments were performed in a one-stage fixed-bed reactor and in a two-stage fixed-bed reactor. In the one-stage reactor......, the shale oil yield reached 7.40 wt % with a reactor temperature profile from 900 to 550 degrees C and decreased to 2.23 wt % with the reverse temperature profile. The effect of the temperature profile was investigated further in the two-stage fixed-bed reactor combining a pyrolysis stage operating at 550...... degrees C and a shale char bed operating at different temperatures. At low temperatures (550 degrees C), severe cracking occurred, converting both heavy and light oil to carbon and gas. The desirably matched reactor temperature profile for high oil yield is discussed via analysis of the tendency...

  6. Stable isotopes and their relationship to temperature and precipitation as recorded in low latitude ice cores

    International Nuclear Information System (INIS)

    Thompson, L.G.; Davis, M.E.; Pin-Nan, Lin

    2002-01-01

    The potential of stable isotopic ratios ( 18 O/ 16 O and 2 H/ 1 H) in mid to low latitude glaciers as modern tools for paleoclimate reconstruction is reviewed. The isotopic composition of precipitation should be viewed not only as a powerful proxy indicator of climate, but also as an additional parameter for understanding climate-induced changes in the water cycle, on both regional and global scales. To interpret quantitatively the ice core isotopic records, the response of the isotopic composition of precipitation to long-term fluctuations of key climatic parameters (temperature, precipitation amount, relative humidity) over a given area should be known. Furthermore, it is important to establish the transfer functions that relate the climate-induced changes of the isotopic composition of precipitation to the isotope record preserved in the glacier. The factors that govern the values of stable isotopes in snowfall are enigmatic and as yet no satisfactory model has been developed to link them directly with any one meteorological or oceanographic factor. This is particularly problematic in the high altitude glaciers in the tropics, where complications are present due not only to continental effects, but also to altitude effects and convective air mass instability, particularly in the monsoon climates of the tropics. This paper presents long and short-term perspectives of isotopic composition variations in ice cores spanning the last 25,000 years from the mid- to low-latitude glaciers. The isotopic records will also be examined as a function of the altitude of the individual coring sites which ranges from 5325 meters to 7200 meters. On the short, term isotopic records from ice cores from the Andes of South America, the Tibetan Plateau and Kilimanjaro in Africa through the year 2000 will be presented. All the tropical glaciers for which data exist are disappearing, and these sites show isotopic enrichment in the 20th century that suggests that large scale low latitude

  7. An Experimental Investigation into the Temperature Profile of a Compliant Foil Air Bearing

    National Research Council Canada - National Science Library

    Radil, Kevin

    2004-01-01

    A series of tests was performed to determine the internal temperature profile in a compliant bump-type foil journal air bearing operating at room temperature under various speeds and load conditions...

  8. FATTY ACID PROFILE IN MILK OF BOVEC SHEEP FED IN THE STABLE OR GRAZED IN DIFFERENT PASTURES

    OpenAIRE

    Cividini, Angela; Simčič, Mojca

    2015-01-01

    The fatty acid profile in the milk of Bovec sheep fed total mixed ratio (TMR) and grazed natural pastures in the lowland (480 m altitude) supplemented with the second harvest (L) as well as grazed different altitude mountain pastures; M1 (1100- 1300 m altitude), M2 (1600-1700 m altitude), M3 (1800 m altitude), M4 (1900 m altitude), M5 (2200 m altitude) were determined. There was an important effect when ewes were turned from the stable to the pasture on all fatty acids. The percentage of α-li...

  9. Automated and temperature-controlled micro-PIV measurements enabling long-term-stable microchannel acoustophoresis characterization

    DEFF Research Database (Denmark)

    Augustsson, Per; Barnkob, Rune; Wereley, Steven T.

    2011-01-01

    We present a platform for micro particle image velocimetry (μPIV), capable of carrying out full-channel, temperature-controlled, long-term-stable, and automated μPIV-measurement of microchannel acoustophoresis with uncertainties below 5% and a spatial resolution in the order of 20 μm. A method to...

  10. Zika Virus Is Not Uniquely Stable at Physiological Temperatures Compared to Other Flaviviruses

    Directory of Open Access Journals (Sweden)

    Leslie Goo

    2016-09-01

    Full Text Available Zika virus (ZIKV is a flavivirus that has emerged as a global health threat due in part to its association with congenital abnormalities. Other globally relevant flaviviruses include dengue virus (DENV and West Nile virus (WNV. High-resolution structures of ZIKV reveal many similarities to DENV and suggest some differences, including an extended glycan loop (D. Sirohi, Z. Chen, L. Sun, T. Klose, T. C. Pierson, et al., 352:467–470, 2016, http://dx.doi.org/10.1126/science.aaf5316 and unique interactions among envelope (E protein residues that were proposed to confer increased virion stability and contribute mechanistically to the distinctive pathobiology of ZIKV (V. A. Kostyuchenko, E. X. Lim, S. Zhang, G. Fibriansah, T. S. Ng, et al., Nature 533:425–428, 2016, http://dx.doi.org/10.1038/nature17994. However, in the latter study, virus stability was inferred by measuring the loss of infectivity following a short incubation period. Here, we rigorously assessed the relative stability of ZIKV, DENV, and WNV by measuring changes in infectivity following prolonged incubation at physiological temperatures. At 37°C, the half-life of ZIKV was approximately twice as long as the half-life of DENV (11.8 and 5.2 h, respectively but shorter than that of WNV (17.7 h. Incubation at 40°C accelerated the loss of ZIKV infectivity. Increasing virion maturation efficiency modestly increased ZIKV stability, as observed previously with WNV and DENV. Finally, mutations at E residues predicted to confer increased stability to ZIKV did not affect virion half-life. Our results demonstrate that ZIKV is not uniquely stable relative to other flaviviruses, suggesting that its unique pathobiology is explained by an alternative mechanism.

  11. Initial evaluation of profiles of temperature, water vapor, and cloud liquid water from a new microwave profiling radiometer.

    Energy Technology Data Exchange (ETDEWEB)

    Liljegren, J. C.; Lesht, B. M.; Clothiaux, E. E.; Kato, S.

    2000-11-01

    To measure the vertical profiles of temperature and water vapor that are essential for modeling atmospheric processes, the Atmospheric Radiation Measurement (ARM) Program of the U. S. Department of Energy launches approximately 2600 radiosondes each year from its Southern Great Plains (SGP) facilities in Oklahoma and Kansas, USA. The annual cost of this effort exceeds $500,000 in materials and labor. Despite the expense, these soundings have a coarse temporal resolution and reporting interval compared with model time steps. In contrast, the radiation measurements used for model evaluations have temporal resolutions and reporting intervals of a few minutes at most. Conversely, radiosondes have a much higher vertical spatial resolution than most models can use. Modelers generally reduce the vertical resolution of the soundings by averaging over the vertical layers of the model. Recently, Radiometries Corporation (Boulder, Colorado, USA) developed a 12-channel, ground-based microwave radiometer capable of providing continuous, real-time vertical profiles of temperature, water vapor, and limited-resolution cloud liquid water from the surface to 10 km in nearly all weather conditions. The microwave radiometer profiler (MWRP) offers a much finer temporal resolution and reporting interval (about 10 minutes) than the radiosonde but a coarser vertical resolution that may be more appropriate for models. Profiles of temperature, water vapor, and cloud liquid water are obtained at 47 levels: from 0 to 1 km above ground level at 100-m intervals and from 1 to 10 km at 250-m intervals. The profiles are derived from the measured brightness temperatures with neural network retrieval. In Figure 1, profiles of temperature, water vapor, and cloud liquid water for 10 May 2000 are presented as time-height plots. MWRP profiles coincident with the 11:31 UTC (05:31 local) and 23:47 UTC (17:47 local) soundings for 10 May are presented in Figures 2 and 3, respectively. These profiles

  12. The effect of temperature on generic stable periodic structures in the parameter space of dissipative relativistic standard map

    Science.gov (United States)

    Horstmann, Ana C. C.; Albuquerque, Holokx A.; Manchein, Cesar

    2017-05-01

    In this work, we have characterized changes in the dynamics of a two-dimensional relativistic standard map in the presence of dissipation and specially when it is submitted to thermal effects modeled by a Gaussian noise reservoir. By the addition of thermal noise in the dissipative relativistic standard map (DRSM) it is possible to suppress typical stable periodic structures (SPSs) embedded in the chaotic domains of parameter space for large enough temperature strengths. Smaller SPSs are first affected by thermal effects, starting from their borders, as a function of temperature. To estimate the necessary temperature strength capable to destroy those SPSs we use the largest Lyapunov exponent to obtain the critical temperature (TC) diagrams. For critical temperatures the chaotic behavior takes place with the suppression of periodic motion, although the temperature strengths considered in this work are not so large to convert the deterministic features of the underlying system into a stochastic ones.

  13. Temporal profile of body temperature in acute ischemic stroke: Relation to infarct size and outcome

    NARCIS (Netherlands)

    M. Geurts (Marjolein); Scheijmans, F.E.V. (Féline E.V.); T. van Seeters (Tom); G.J. Biessels; L.J. Kappelle (Jaap); B.K. Velthuis (Birgitta K.); H.B. van der Worp (Bart); C.B. Majoie (Charles); Y.B.W.E.M. Roos (Yvo); L.E.M. Duijm (Lucien); K. Keizer (Koos); A. van der Lugt (Aad); D.W.J. Dippel (Diederik); Greve, D. (Droogh-de); H.P. Bienfait (Henri); M.A.A. van Walderveen (Marianne); M.J.H. Wermer (Marieke); G.J. Lycklama à Nijeholt (Geert); J. Boiten (Jelis); A. Duyndam (Anita); V.I.H. Kwa; F.J. Meijer (F.); E.J. van Dijk (Ewoud); A.M. Kesselring (Anouk); J. Hofmeijer; J.A. Vos (Jan Albert); W.J. Schonewille (Wouter); W.J. van Rooij (W.); P.L.M. de Kort (Paul); C.C. Pleiter (C.); S.L.M. Bakker (Stef); Bot, J.; M.C. Visser (Marieke); B.K. Velthuis (Birgitta); I.C. van der Schaaf (Irene); J.W. Dankbaar (Jan); W.P. Mali (Willem); van Seeters, T.; A.D. Horsch (Alexander D.); J.M. Niesten (Joris); G.J. Biessels (Geert Jan); L.J. Kappelle (Jaap); J.S.K. Luitse; Y. van der Graaf (Yolanda)

    2016-01-01

    textabstractBackground: High body temperatures after ischemic stroke have been associated with larger infarct size, but the temporal profile of this relation is unknown. We assess the relation between temporal profile of body temperature and infarct size and functional outcome in patients with acute

  14. Transport studies in FTU with decoupled temperature and current density profiles

    International Nuclear Information System (INIS)

    Bracco, G.; Buratti, P.; Micozzi, P.; Tudisco, O.

    1994-01-01

    Electron temperature profiles in tokamaks are subject to global constraints that can be attributed either to their link with current profiles, i.e. to MHD stability conditions, a clear example being sawtooth activity, or to other mechanisms like marginal stability. Also a direct effect on transport coefficients was attributed to the current profile. Fast current ramps in FTU ohmic pulses have been used to study the effect of current profile variations on the energy confinement time. The global profile constraint was transiently removed in these pulses, and variations in the shape of temperature profiles could be observed. Modified profiles were also observed in pulses with a strong central radiative sink; in this case the modification was not transient. Finally, the transport properties in the central region have been studied by the analysis of temperature evolution between crashes of very long period sawteeth; very small electron heat transport was found. (author) 6 refs., 5 figs

  15. Ice-Tethered Profiler observations: Vertical profiles of temperature, salinity, oxygen, and ocean velocity from an Ice-Tethered Profiler buoy system

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This collection contains repeated vertical profiles of ocean temperature and salinity versus pressure, as well as oxygen and velocity for some instruments. Data were...

  16. Proinsulin is stable at room temperature for 24 hours in EDTA: A clinical laboratory analysis (adAPT 3.

    Directory of Open Access Journals (Sweden)

    Jane Davidson

    Full Text Available Reference laboratories advise immediate separation and freezing of samples for the assay of proinsulin, which limit its practicability for smaller centres. Following the demonstration that insulin and C-peptide are stable in EDTA at room temperature for at least 24hours, we undertook simple stability studies to establish whether the same might apply to proinsulin.Venous blood samples were drawn from six adult women, some fasting, some not, aliquoted and assayed immediately and after storage at either 4°C or ambient temperature for periods from 2h to 24h.There was no significant variation or difference with storage time or storage condition in either individual or group analysis.Proinsulin appears to be stable at room temperature in EDTA for at least 24h. Immediate separation and storage on ice of samples for proinsulin assay is not necessary, which will simplify sample transport, particularly for multicentre trials.

  17. Electron temperature profile behaviour in TFTR during neutral beam injection and multiple pellet fuelling

    International Nuclear Information System (INIS)

    Taylor, G.; Fredrickson, E.D.; Grek, B.

    1989-01-01

    The electron temperature profiles on the Tokamak Fusion Test Reactor (TFTR) are determined by several diagnostics, including multi-point Thomson scattering and electron cyclotron emission measured with heterodyne radiometers and a Michelson interferometer. The electron temperature profiles are characterized by very high central temperatures (> 8 keV) and large Shafranov shifts (> 35 cm). The large Shafranov shifts suggest the necessity of mapping to magnetic flux surfaces when investigating the profile behaviour. During 1986, TFTR was operated with up to 20 MW of deuterium neutral beam injection (NBI) and a deuterium pellet injector. The electron temperature profile measurements were made on plasmas with 2.7 T p dia up to 2.2, 1x10 19 e 20 m -3 and 2.5 cyl e (R) to flux surfaces are investigated as well as the extent to which the electron temperature profile away from the core remains invariant to these perturbations. (author). 27 refs, 14 figs

  18. A Stable, Extreme Temperature, High Radiation, Compact. Low Power Clock Oscillator for Space, Geothermal, Down-Hole & other High Reliability Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Efficient and stable clock signal generation requirements at extreme temperatures and high radiation are not met with the current solutions. Chronos Technology...

  19. Comparison of winter temperature profiles in asphalt and concrete pavements.

    Science.gov (United States)

    2014-06-01

    The objectives of this research were to 1) determine which pavement type, asphalt or concrete, has : higher surface temperatures in winter and 2) compare the subsurface temperatures under asphalt and : concrete pavements to determine the pavement typ...

  20. Retrieval of humidity and temperature profiles over the oceans from ...

    Indian Academy of Sciences (India)

    , viz., temperature only retrieval, humidity only retrieval and combined retrieval. The temperature/humidity ... to provide a quantitative estimate of the temper- ature and humidity, and .... The neurons being building blocks of these neural network ...

  1. Temperature and density profiles of an MHD switch on shock

    International Nuclear Information System (INIS)

    Watson-Munro, C.N.; Bighel, L.; Collins, A.R.; Cramer, N.F.; Cross, R.C.

    1975-02-01

    An experimental study of the structure of MHD switch-on shock waves propagating into partially ionized hydrogen and helium plasmas is described. The variation of electron and ion temperatures through the shock front was studied as a function of the level of preionization. When the shock propagates into an almost fully ionized plasma, the electron temperatures rises well above the ion temperature due to resistive heating of the electrons. At low preionization levels however, the ion temperature rises above the electron temperature. These results indicate that ion-neutral collisions can play a dominant role in the dissipation of energy in a shock wave. (author)

  2. Thermal Buckling Analysis of Rectangular Panels Subjected to Humped Temperature Profile Heating

    Science.gov (United States)

    Ko, William I.

    2004-01-01

    This research investigates thermal buckling characteristics of rectangular panels subjected to different types of humped temperature profile heating. Minimum potential energy and finite-element methods are used to calculate the panel buckling temperatures. The two methods give fairly close thermal buckling solutions. 'Buckling temperature magnification factor of the first kind, eta' is established for the fixed panel edges to scale up the buckling solution of uniform temperature loading case to give the buckling solution of the humped temperature profile loading cases. Also, 'buckling temperature magnification factor of the second kind, xi' is established for the free panel edges to scale up the buckling solution of humped temperature profile loading cases with unheated boundary heat sinks to give the buckling solutions when the boundary heat sinks are heated up.

  3. Profiling and relative quantification of phosphatidylethanolamine based on acetone stable isotope derivatization.

    Science.gov (United States)

    Wang, Xiang; Wei, Fang; Xu, Ji-Qu; Lv, Xin; Dong, Xu-Yan; Han, Xianlin; Quek, Siew-Young; Huang, Feng-Hong; Chen, Hong

    2016-01-01

    Phosphatidylethanolamine (PE) is considered to be one of the pivotal lipids for normal cellular function as well as disease initiation and progression. In this study, a simple, efficient, reliable, and inexpensive method for the qualitative analysis and relative quantification of PE, based on acetone stable isotope derivatization combined with double neutral loss scan-shotgun electrospray ionization tandem-quadrupole mass spectrometry analysis (ASID-DNLS-Shotgun ESI-MS/MS), was developed. The ASID method led to alkylation of the primary amino groups of PE with an isopropyl moiety. The use of acetone (d0-acetone) and deuterium-labeled acetone (d6-acetone) introduced a 6 Da mass shift that was ideally suited for relative quantitative analysis, and enhanced sensitivity for mass analysis. The DNLS model was introduced to simultaneously analyze the differential derivatized PEs by shotgun ESI-MS/MS with high selectivity and accuracy. The reaction specificity, labeling efficiency, and linearity of the ASID method were thoroughly evaluated in this study. Its excellent applicability was validated by qualitative and relative quantitative analysis of PE species presented in liver samples from rats fed different diets. Using the ASID-DNLS-Shotgun ESI-MS/MS method, 45 PE species from rat livers have been identified and quantified in an efficient manner. The level of total PEs tended to decrease in the livers of rats on high fat diets compared with controls. The levels of PE 32:1, 34:3, 34:2, 36:3, 36:2, 42:10, plasmalogen PE 36:1 and lyso PE 22:6 were significantly reduced, while levels of PE 36:1 and lyso PE 16:0 increased. Copyright © 2015 Elsevier B.V. All rights reserved.

  4. Stable isotope (?13C profiling of xylitol and sugar in South Africa

    Directory of Open Access Journals (Sweden)

    Craig Symes

    2017-05-01

    Full Text Available Xylitol is an alternative sweetener to sucrose, glucose and fructose, and is available under a number of brands in South Africa. Carbon stable isotope values (δ13C of a selection of commercially available xylitol products (n=28 were analysed and compared with sugar samples (n=29. Sugarcane (C4 and beet sugar (C3 derived sugar samples aligned with published values of source, although two samples that indicated a sugarcane origin suggested a beet sugar origin. Control corn-derived samples defined a stepwise xylose to xylitol discrimination of +0.7‰. The distinction between C3- and C4-derived xylitol was less clear with three samples difficult to define (range = -14.8 to -17.1‰. The values for a suite of xylitol samples (-22.3‰ to -19.7‰; n=8 that aligned closely with a suspected C3-derived xylose, were ~8‰ more positive than known birch isotope values. Some xylitol samples may thus represent (1 a mixture of C3- and C4-derived products, (2 derivation from a CAM species source or (3 different processing techniques in which the discrimination values of xylose from corn, and xylose from birch, may differ because of the respective chemical processing techniques. No samples that claimed a birch bark origin were within the range of samples suggested to be corn derived (i.e. -13.0‰ to -9.7‰, n=16. We suggest that the threshold values provided are relatively robust for defining the origins of xylitol and sugar, and can be used in determining the authenticity and claims of suppliers and producers.

  5. Effects of furnace temperature profile on the interface shape during Bridgman crystal growth

    Science.gov (United States)

    Taghavi, K.; Duval, W. M. B.

    1988-01-01

    The effects of asymmetry in furnace temperature profile and pulling velocity on the crystal interface shape are demonstrated while neglecting the latent heat of solidification. It is concluded that the furnace temperature profile may be varied in order to influence the interface shape of the crystal. An exact thermal analysis is performed on the Bridgman technique by including the latent heat of solidification as a source term. The exact temperature field is obtained for the case of a flat melt-crystal interface. The earlier observation regarding the influence of furnace temperature profile on the crystal interface shape is confirmed and a criterion for a flat crystal interface is obtained. Various furnace temperature profiles are selected and their corresponding results are presented.

  6. The abnormal temperature profile of accreting disk around the Kerr black hole

    International Nuclear Information System (INIS)

    Zhang, J.; Jiang, S.

    1983-01-01

    In this paper, we used the more rigorous general relativistic viscous hydrodynamical equation to discuss and calculate the temperature profile in the accreting disk around a Kerr black hole. It is found that for an accreting disk around a Kerr black hole, the occurrence of extremum values in the temperature profile is indeed possible. Furthermore, the temperature profile is always the same - no matter what kind of viscous mechanism is adopted - if the radiative mechanism of the materials in the disk is black-body radiation. For free-free radiation, we adopted the so-called α-viscosity law model to get a solution analogous to that obtained earlier (Fang et al., 1980). The calculations show that there exists a fast cooling ring region lying just inside the temperature maximum. In this ring region, there are probably some pecularities which do not exist in the usual temperature profile calculation (Fang, 1981). (orig.)

  7. Stable carbon isotope ratio profiling of illicit testosterone preparations--domestic and international seizures.

    Science.gov (United States)

    Brooker, Lance; Cawley, Adam; Drury, Jason; Edey, Claire; Hasick, Nicole; Goebel, Catrin

    2014-10-01

    Gas chromatography-combustion-isotope ratio mass spectrometry (GC-C-IRMS) is now established as a robust and mature analytical technique for the doping control of endogenous anabolic androgenic steroids in human sport. It relies on the assumption that the carbon isotope ratios of naturally produced steroids are significantly different to synthetically manufactured testosterone or testosterone prohormones used in commercial medical or dietary supplement products. Recent publications in this journal have highlighted the existence of black market testosterone preparations with carbon isotope ratios within the range reported for endogenous steroids (i.e. δ(13) C ≥ -25.8 ‰). In this study, we set out to profile domestic and international law enforcement seizures of illicit testosterone products to monitor the prevalence of 'enriched' substrates--which if administered to human subjects would be considered problematic for the use of current GC-C-IRMS methodologies for the doping control of testosterone in sport. The distribution of δ(13) C values for this illicit testosterone sample population (n = 283) ranged from -23.4 ‰ to -32.9 ‰ with mean and median of -28.6 ‰--comparable to previous work. However, only 13 out of 283 testosterone samples (4.6 %) were found to display δ(13) C values ≥ -25.8 ‰, confirming that in the vast majority of cases of illicit testosterone administration, current GC-C-IRMS doping control procedures would be capable of confirming misuse. Copyright © 2014 John Wiley & Sons, Ltd.

  8. Blood pressure and antihypertensive medication profile in a multiethnic Asian population of stable chronic kidney disease patients.

    Science.gov (United States)

    Teo, Boon Wee; Chua, Horng Ruey; Wong, Weng Kin; Haroon, Sabrina; Subramanian, Srinivas; Loh, Ping Tyug; Sethi, Sunil; Lau, Titus

    2016-05-01

    Clinical practice guidelines recommend different blood pressure (BP) goals for chronic kidney disease (CKD) patients. Usage of antihypertensive medication and attainment of BP targets in Asian CKD patients remain unclear. This study describes the profile of antihypertensive agents used and BP components in a multiethnic Asian population with stable CKD. Stable CKD outpatients with variability of serum creatinine levels 3 months apart, were recruited. Mean systolic blood pressure (SBP) and diastolic blood pressure (DBP) were measured using automated manometers, according to practice guidelines. Serum creatinine was assayed and the estimated glomerular filtration rate (GFR) calculated using the CKD Epidemiology Collaboration equation. BP and antihypertensive medication profile was examined using univariate analyses. 613 patients (55.1% male; 74.7% Chinese, 6.4% Indian, 11.4% Malay; 35.7% diabetes mellitus) with a mean age of 57.8 ± 14.5 years were recruited. Mean SBP was 139 ± 20 mmHg, DBP was 74 ± 11 mmHg, serum creatinine was 166 ± 115 µmol/L and GFR was 53 ± 32 mL/min/1.73 m(2). At a lower GFR, SBP increased (p < 0.001), whereas DBP decreased (p = 0.0052). Mean SBP increased in tandem with the number of antihypertensive agents used (p < 0.001), while mean DBP decreased when ≥ 3 antihypertensive agents were used (p = 0.0020). Different targets are recommended for each BP component in CKD patients. A majority of patients cannot attain SBP targets and/or exceed DBP targets. Research into monitoring and treatment methods is required to better define BP targets in CKD patients. Copyright: © Singapore Medical Association.

  9. Strong anisotropy in the low temperature Compton profiles of ...

    Indian Academy of Sciences (India)

    Compton profiles of momentum distribution of conduction electrons in the orthorhombic phase of -Ga metal at low temperature are calculated in the band model for the three crystallographic directions (100), (010), and (001). Unlike the results at room temperature, previously reported by Lengeler, Lasser and Mair, the ...

  10. An array for measuring detailed soil temperature profiles

    Science.gov (United States)

    Soil temperature dynamics can provide insights into soil variables which are much more difficult or impossible to measure. We designed an array to measure temperature at precise depth increments. Data was collected to determine if the construction materials influence surface and near-surface tempera...

  11. Detection of uranium extraction zone by axial temperature profiles in a pulsed column for Purex process

    International Nuclear Information System (INIS)

    Tsukada, T.; Takahashi, K.

    1991-01-01

    A new method was presented for detecting uranium extraction zone in a pulsed column by means of measuring axial temperature profile originated from reaction heat during uranium extraction. Key parameters of the temperature profiles were estimated with a code developed for calculating temperature profiles in a direct-contact heat exchanger such as a pulsed column, and were verified using data from a small pulsed column simulating reaction heat with injecting hot water. Finally, the results were compared with those from an actual uranium extraction tests, indicating that the method presented was promising for detecting uranium extraction zone in a pulsed column. (author)

  12. Measurements of flow velocity and temperature profile in a propane-oxygen combustion MHD channel

    International Nuclear Information System (INIS)

    Aoki, Yoshiaki; Kayukawa, Naoyuki; Yamazaki, Hatsuo

    1986-01-01

    In a propane-oxygen combustion MHD channel, experimental measurements were made of the plasma flow velocity by means of a cross-correlation function analysis and of the boundary-layer temperature-profile by a newly-devised light-polarization line-reversal method. The following results were obtained: the velocity decreased gradually, the temperature profile of the boundary layer varied appreciably as the magnitude of the externally applied magnetic field increased, and the temperature increased from Joule heating, making the boundary layer profile steeper. (author)

  13. Stable Isotope Profiling of Internet-Sourced Viagra® and 'generic- Viagra' Tablets

    Science.gov (United States)

    Kemp, Helen; Meier-Augenstein, Wolfram

    2013-04-01

    Viagra® manufactured by Pfizer was the first prescription drug for the treatment of erectile dysfunction (ED), a condition that is estimated to affect 1 in 10 men at some stage in their lives (1). Viagra® contains the active pharmaceutical ingredient (API) sildenafil, as the citrate salt. Sildenafil, along with Tadalafil and Vardenafil belong to a class of drugs known as phosphodiesterase type 5 (PDE5) inhibitors. Since its first production in 1998, Viagra® has generated well in excess of 10 billion US dollars in sales (2) and with Pfizers' patent extended to April 2020 (3) it still remains the only sildenafil-based treatment option for sufferers of ED in the US. There are no legal 'generic-Viagra' formulations available in the US. However, formulations containing sildenafil citrate as API are widely available over the internet and often sold as 'generic Viagra'. These cheaper alternatives are often manufactured under less than ideal conditions with little or no QA/QC procedures in place. The World Health Organisation recognised the scale of the problem in its 2010 bulletin "Growing threat from counterfeit medicines" (4) and quotes a Dutch study cited in the International Journal of Clinical Practice in which from a cohort of 370 seized Viagra® samples, only 10 were genuine. We sourced a variety of tablets sold for the treatment of ED which claimed to have sildenafil citrate as API. Viagra®, 'generic-Viagra', Kamagra, Silagra and Filagra tablets were ordered via the internet and supplied from both UK-based pharmacies as well as overseas suppliers (Hong Kong, India, Vanuata). In this small-scale pilot study, we present results from bulk 2H/18O and 13C/15N stable isotope analysis performed on crushed tablets from 23 samples of internet-sourced tablets sold for the treatment of ED and purported to contain sildenafil citrate as API. References 1. www.healthcare.org.uk 2. www.moneynews.com 3. US Patent & trademark office (www.uspto.gov) 4. WHO bulletin 2010; 88:247-248

  14. Profiling and relative quantification of phosphatidylethanolamine based on acetone stable isotope derivatization

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Xiang [Oil Crops Research Institute of the Chinese Academy of Agricultural Sciences, Key Laboratory of Biology and Genetic Improvement of Oil Crops, Ministry of Agriculture (China); Hubei Key Laboratory of Lipid Chemistry and Nutrition (China); Wei, Fang, E-mail: willasa@163.com [Oil Crops Research Institute of the Chinese Academy of Agricultural Sciences, Key Laboratory of Biology and Genetic Improvement of Oil Crops, Ministry of Agriculture (China); Hubei Key Laboratory of Lipid Chemistry and Nutrition (China); Xu, Ji-qu; Lv, Xin; Dong, Xu-yan [Oil Crops Research Institute of the Chinese Academy of Agricultural Sciences, Key Laboratory of Biology and Genetic Improvement of Oil Crops, Ministry of Agriculture (China); Hubei Key Laboratory of Lipid Chemistry and Nutrition (China); Han, Xianlin [Center for Metabolic Origins of Disease, Sanford Burnham Prebys Medical Discovery Institute, Orlando, FL 32827 (United States); College of Basic Medical Sciences, Zhejiang Chinese Medical University, 548 Bingwen Road, Hangzhou, Zhejiang 310053 (China); Quek, Siew-young [School of Chemical Science, The University of Auckland, Auckland 1142 (New Zealand); Huang, Feng-hong [Oil Crops Research Institute of the Chinese Academy of Agricultural Sciences, Key Laboratory of Biology and Genetic Improvement of Oil Crops, Ministry of Agriculture (China); Hubei Key Laboratory of Lipid Chemistry and Nutrition (China); Chen, Hong, E-mail: chenhong@oilcrops.cn [Oil Crops Research Institute of the Chinese Academy of Agricultural Sciences, Key Laboratory of Biology and Genetic Improvement of Oil Crops, Ministry of Agriculture (China); Hubei Key Laboratory of Lipid Chemistry and Nutrition (China)

    2016-01-01

    Phosphatidylethanolamine (PE) is considered to be one of the pivotal lipids for normal cellular function as well as disease initiation and progression. In this study, a simple, efficient, reliable, and inexpensive method for the qualitative analysis and relative quantification of PE, based on acetone stable isotope derivatization combined with double neutral loss scan-shotgun electrospray ionization tandem-quadrupole mass spectrometry analysis (ASID-DNLS-Shotgun ESI-MS/MS), was developed. The ASID method led to alkylation of the primary amino groups of PE with an isopropyl moiety. The use of acetone (d{sub 0}-acetone) and deuterium-labeled acetone (d{sub 6}-acetone) introduced a 6 Da mass shift that was ideally suited for relative quantitative analysis, and enhanced sensitivity for mass analysis. The DNLS model was introduced to simultaneously analyze the differential derivatized PEs by shotgun ESI-MS/MS with high selectivity and accuracy. The reaction specificity, labeling efficiency, and linearity of the ASID method were thoroughly evaluated in this study. Its excellent applicability was validated by qualitative and relative quantitative analysis of PE species presented in liver samples from rats fed different diets. Using the ASID-DNLS-Shotgun ESI-MS/MS method, 45 PE species from rat livers have been identified and quantified in an efficient manner. The level of total PEs tended to decrease in the livers of rats on high fat diets compared with controls. The levels of PE 32:1, 34:3, 34:2, 36:3, 36:2, 42:10, plasmalogen PE 36:1 and lyso PE 22:6 were significantly reduced, while levels of PE 36:1 and lyso PE 16:0 increased. - Highlights: • A novel isotope reagent acetone was explored for the derivatization of PEs. • The labeling reaction was carried out under mild conditions with high specificity. • Enhanced detection sensitivity of PEs was achieved after derivatization. • The ASID-DNLS-Shotgun MS/MS method was used to relative quantification of PEs.

  15. Long-term summer temperature variations in the Pyrenees from detrended stable carbon isotopes

    Czech Academy of Sciences Publication Activity Database

    Esper, J.; Konter, O.; Krusic, P. J.; Saurer, M.; Holzkaemper, S.; Büntgen, Ulf

    2015-01-01

    Roč. 42, č. 1 (2015), s. 53-59 ISSN 1897-1695 Institutional support: RVO:67179843 Keywords : tree-rings * climate sensitivity * past millennium * delta-o-18 * delta-c-13 * cellulose * wood * uncertainties * chronologies * variability * Climate change * paleoclimatology * stable isotope geochemistry * tree-rings * Europe Subject RIV: DG - Athmosphere Sciences, Meteorology Impact factor: 2.038, year: 2015

  16. Botanical traceability of commercial tannins using the mineral profile and stable isotopes.

    Science.gov (United States)

    Bertoldi, Daniela; Santato, Alessandro; Paolini, Mauro; Barbero, Alice; Camin, Federica; Nicolini, Giorgio; Larcher, Roberto

    2014-09-01

    Commercial tannins are natural polyphenolic compounds extracted from different plant tissues such as gall, the wood of different species and fruit. In the food industry they are mainly used as flavourings and food ingredients, whereas in winemaking they are classified as clarification agents for wine protein stabilisation, although colour stabilisation, metal removal, unpleasant thiol removal and rheological correction are also well-known and desired effects. Due to their particular technical properties and very different costs, the possibility of correct identification of the real botanical origin of tannins can be considered a primary target in oenology research and in fulfilling the technical and economic requirements of the wine industry. For some categories of tannins encouraging results have already been achieved by considering sugar or polyphenolic composition. For the first time this work verifies the possibility of determining the botanical origin of tannins on the basis of the mineral element profile and analysis of the (13) C/(12) C isotopic ratio. One hundred two commercial tannins originating from 10 different botanical sources (grapes, oak, gall, chestnut, fruit trees, quebracho, tea, acacia, officinal plants and tara) were analysed to determine 57 elements and the (13) C/(12) C isotopic ratio, using inductively coupled plasma mass spectrometry and isotope-ratio mass spectrometry, respectively. Forward stepwise discriminant analysis provided good discrimination between the 8 most abundant groups, with 100% correct re-classification. The model was then validated five times on subsets of 10% of the overall samples, randomly extracted, achieving satisfactory results. With a similar approach it was also possible to distinguish toasted and untoasted oak tannins as well as tannins from grape skin and grape seeds. Copyright © 2014 John Wiley & Sons, Ltd.

  17. Long-term carbon and nitrogen dynamics at SPRUCE revealed through stable isotopes in peat profiles

    Science.gov (United States)

    Hobbie, Erik A.; Chen, Janet; Hanson, Paul J.; Iversen, Colleen M.; McFarlane, Karis J.; Thorp, Nathan R.; Hofmockel, Kirsten S.

    2017-05-01

    Peatlands encode information about past vegetation dynamics, climate, and microbial processes. Here, we used δ15N and δ13C patterns from 16 peat profiles to deduce how the biogeochemistry of the Marcell S1 forested bog in northern Minnesota responded to environmental and vegetation change over the past ˜ 10 000 years. In multiple regression analyses, δ15N and δ13C correlated strongly with depth, plot location, C / N, %N, and each other. Correlations with %N, %C, C / N, and the other isotope accounted for 80 % of variance for δ15N and 38 % of variance for δ13C, reflecting N and C losses. In contrast, correlations with depth and topography (hummock or hollow) reflected peatland successional history and climate. Higher δ15N in plots closer to uplands may reflect upland-derived DON inputs and accompanying shifts in N dynamics in the lagg drainage area surrounding the bog. The Suess effect (declining δ13CO2 since the Industrial Revolution) lowered δ13C in recent surficial samples. High δ15N from -35 to -55 cm probably indicated the depth of ectomycorrhizal activity after tree colonization of the peatland over the last 400 years, as confirmed by the occasional presence of wood down to -35 cm depth. High δ13C at ˜ 4000 years BP (-65 to -105 cm) could reflect a transition at that time to slower rates of peat accumulation, when 13C discrimination during peat decomposition may increase in importance. Low δ13C and high δ15N at -213 and -225 cm ( ˜ 8500 years BP) corresponded to a warm period during a sedge-dominated rich fen stage. The above processes appear to be the primary drivers of the observed isotopic patterns, whereas there was no clear evidence for methane dynamics influencing δ13C patterns.

  18. Influence of temperature inhomogeneity on product profile of ...

    Indian Academy of Sciences (India)

    ... reaction and diffusion due to the presence of a hot zone in addition to that which normally exists via concentration. Implications of this coupling for the product profile of a reaction are discussed. We also propose a mechanism by which mobility of ions or diffusion of molecular species within biomembranes may take place.

  19. Retrieval of humidity and temperature profiles over the oceans from ...

    Indian Academy of Sciences (India)

    humidity retrieval performance from FENGYUN-. 3A datasets. Passive microwave humidity retrievals ..... The Bayesian statistical framework has been used widely for the inverse problems in the last few. Figure 8. Eigen vectors of humidity profiles. INSAT 3D observations. Filter pixels over land. Filter cloudy pixels. Estimate.

  20. Strong anisotropy in the low temperature Compton profiles of ...

    Indian Academy of Sciences (India)

    B P PANDA and N C MOHAPATRA£. Department of Physics, Chikiti Mahavidyalaya, Chikiti 761 010, India. £Department of Physics, Berhampur University, Berhampur 760 007, India. MS received 12 April 2001; revised 1 September 2001. Abstract. Compton profiles of momentum distribution of conduction electrons in the ...

  1. Carbon Availability Modifies Temperature Responses of Heterotrophic Microbial Respiration, Carbon Uptake Affinity, and Stable Carbon Isotope Discrimination.

    Science.gov (United States)

    Min, Kyungjin; Lehmeier, Christoph A; Iv, Ford Ballantyne; Billings, Sharon A

    2016-01-01

    Microbial transformations of organic carbon (OC) generate a large flux of CO 2 into the atmosphere and influence the C balance of terrestrial and aquatic ecosystems. Yet, inherent heterogeneity in natural environments precludes direct quantification of multiple microbial C fluxes that underlie CO 2 production. Here we used a continuous flow bioreactor coupled with a stable C isotope analyzer to determine the effects of temperature and C availability (cellobiose concentration) on C fluxes and 13 C discrimination of a microbial population growing at steady-state in a homogeneous, well-mixed environment. We estimated C uptake affinity and C use efficiency (CUE) to characterize the physiological responses of microbes to changing environmental conditions. Temperature increased biomass-C specific respiration rate and C uptake affinity at lower C availability, but did not influence those parameters at higher C availability. CUE decreased non-linearly with increasing temperature. The non-linear, negative relationship between CUE and temperature was more pronounced under lower C availability than under relatively high C availability. We observed stable isotope fractionation between C substrate and microbial biomass C (7~12‰ depletion), and between microbial biomass and respired CO 2 (4~10‰ depletion). Microbial discrimination against 13 C-containing cellobiose during C uptake was influenced by temperature and C availability, while discrimination during respiration was only influenced by C availability. Shifts in C uptake affinity with temperature and C availability may have modified uptake-induced 13 C fractionation. By stressing the importance of C availability on temperature responses of microbial C fluxes, C uptake affinity, CUE, and isotopic fractionation, this study contributes to a fundamental understanding of C flow through microbes. This will help guide parameterization of microbial responses to varying temperature and C availability within Earth-system models.

  2. Stable Co-crystals of Glipizide with Enhanced Dissolution Profiles: Preparation and Characterization.

    Science.gov (United States)

    Pandey, Narendra Kumar; Sehal, Hans Raj; Garg, Varun; Gaur, Tejasvi; Kumar, Bimlesh; Singh, Sachin Kumar; Gulati, Monica; Gowthamarajan, K; Bawa, Palak; Rajesh, Sarvi Yadav; Sharma, Parth; Narang, Rakesh

    2017-10-01

    Present study deciphers preparation of co-crystals of lipophilic glipizide by using four different acids, oxalic, malonic, stearic, and benzoic acids, in order to achieve enhanced solubility and dissolution along with stability. All co-crystals were prepared by dissolving drug and individual acids in the ratio of 1:0.5 in acetonitrile at 60-70°C for 15 min, followed by cooling at room temperature for 24 h. FT-IR spectroscopy revealed no molecular interaction between acids and drug as the internal structure and their geometric configurations remain unchanged. Differential scanning calorimetry revealed closer melting points of raw glipizide and its co-crystals, which speculates absence of difference in crystallinity as well as intermolecular bonding of the co-crystals and drug. PXRD further revealed that all the co-crystals were having similar crystallinity as that of raw glipizide except glipizide-malonic acid co-crystals. This minor difference in the relative intensities of some of the diffraction peaks could be attributed to the crystal habit or crystal size modification. SEM revealed difference in the crystal morphology for all the co-crystals. Micromeritic, solubility, dissolution, and stability data revealed that among all the prepared co-crystals, glipizide-stearic acid co-crystals were found superior. Hence, it was concluded that glipizide-stearic acid co-crystals could offer an improved drug design strategy to overcome dissolution and bioavailability related challenges associated with lipophilic glipizide.

  3. Temperature profile evolution in quenching high-Tc ...

    Indian Academy of Sciences (India)

    temperature superconductors (HTS) in all practical applications. As a consequence of quench, transport current gets diverted to the matrix stabilizer material of the high-c composite and causes Joule heating till the original conditions are restored.

  4. SMEX02 Soil Moisture and Temperature Profiles, Walnut Creek, Iowa

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set contains rainfall, soil moisture, and soil temperature data collected for the Soil Moisture Experiment 2002 (SMEX02). The parameters measured are soil...

  5. Transcriptome profiling of sweetpotato tuberous roots during low temperature storage.

    Science.gov (United States)

    Ji, Chang Yoon; Chung, Won-Hyong; Kim, Ho Soo; Jung, Won Yong; Kang, Le; Jeong, Jae Cheol; Kwak, Sang-Soo

    2017-03-01

    Sweetpotato [Ipomoea batatas (L.) Lam] is a globally important root crop with high industrial value. However, because sweetpotato tuberous roots undergo chilling injuries that negatively affect their quality at temperatures below 10 °C, postharvest damage during the winter season is a major constraint for industrialization. To understand chilling injury response during postharvest low temperature storage, we used next-generation sequencing technology to comprehensive analyze the transcriptome of tuberous roots stored at optimal (13 °C) or low temperature (4 °C) for 6 weeks. From nine cDNA libraries, we produced 298,765,564 clean reads, which were de novo assembled into 58,392 unigenes with an average length of 1100 bp. A total of 3216 differentially expressed genes (DEGs) were detected and categorized into six clusters, of which clusters 2, 4, and 5 (1464 DEGs) were up-regulated under low temperature. The genes in these three clusters are involved in biosynthesis of unsaturated fatty acids, pathogen defense, and phenylalanine metabolism. By contrast, genes in clusters 1, 3, and 6 (1752 DEGs), which were generally down-regulated at low temperature, encode antioxidant enzymes or are involved in glycerophospholipid, carbohydrate, or energy metabolism. We confirmed the results of the transcriptome analysis by quantitative RT-PCR. Our transcriptome analysis will advance our understanding of the comprehensive mechanisms of chilling injury during low temperature storage and facilitate improvements in postharvest storage of sweetpotato tuberous roots. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

  6. Note: A temperature-stable low-noise transimpedance amplifier for microcurrent measurement

    Science.gov (United States)

    Xie, Kai; Shi, Xueyou; Zhao, Kai; Guo, Lixin; Zhang, Hanlu

    2017-02-01

    Temperature stability and noise characteristics often run contradictory in microcurrent (e.g., pA-scale) measurement instruments because low-noise performance requires high-value resistors with relatively poor temperature coefficients. A low-noise transimpedance amplifier with high-temperature stability, which involves an active compensation mechanism to overcome the temperature drift mainly caused by high-value resistors, is presented. The implementation uses a specially designed R-2R compensating network to provide programmable current gain with extra-fine trimming resolution. The temperature drifts of all components (e.g., feedback resistors, operational amplifiers, and the R-2R network itself) are compensated simultaneously. Therefore, both low-temperature drift and ultra-low-noise performance can be achieved. With a current gain of 1011 V/A, the internal current noise density was about 0.4 fA/√Hz, and the average temperature coefficient was 4.3 ppm/K at 0-50 °C. The amplifier module maintains accuracy across a wide temperature range without additional thermal stabilization, and its compact size makes it especially suitable for high-precision, low-current measurement in outdoor environments for applications such as electrochemical emission supervision, air pollution particles analysis, radiation monitoring, and bioelectricity.

  7. Low-temperature atomic layer deposition delivers more active and stable Pt-based catalysts

    NARCIS (Netherlands)

    Bui, H.V.; Grillo, F.; Kulkarni, S.S.; Bevaart, Ronald; Nguyên, V.T.; van der Linden, B.; Moulijn, J.A.; Makkee, M.; Kreutzer, M.T.; van Ommen, J.R.

    2017-01-01

    We tailored the size distribution of Pt nanoparticles (NPs) on graphene nanoplatelets at a given metal loading by using low-temperature atomic layer deposition carried out in a fluidized bed reactor operated at atmospheric pressure. The Pt NPs deposited at low temperature (100 °C) after 10 cycles

  8. Soil Moisture Profiles and Temperature Data from SoilSCAPE Sites, USA

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set contains in-situ soil moisture profile and soil temperature data collected at 20-minute intervals at SoilSCAPE (Soil moisture Sensing Controller and...

  9. Oceanographic profile temperature and salinity from JCAD-6 drifting buoy 2003-2004 (NODC Accession 0002236)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Oceanographic profile temperature and salinity measurements collected using a drifting buoy in the Arctic from 2003 to 2004 (NODC Accession 0002236).

  10. Stratospheric and Mesospheric Pressure-Temperature Profiles from the Rotational Analysis of CO subscript2 Lines

    Science.gov (United States)

    Gunson, M.; Lowes, L.; Abrams, M.; Raper, O.; Farmer, C.; Stiller, G.; Zander, R.; Rinsland, C.

    1994-01-01

    A simple, classical, and expedient method for the retrieval of atmospheric pressure-temperature profiles has been applied to the high-resolution infrared solar absorption spectra obtained with the Atmospheric Trace Molecule Spectroscopy (ATMOS) instrument.

  11. A Mathematical Technique for Estimating True Temperature Profiles of Data Obtained from Long Time Constant Thermocouples

    National Research Council Canada - National Science Library

    Young, Graeme

    1998-01-01

    A mathematical modeling technique is described for estimating true temperature profiles of data obtained from long time constant thermocouples, which were used in fuel fire tests designed to determine...

  12. MGS RS: ATMOSPHERIC TEMPERATURE-PRESSURE PROFILES V1.0

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set contains over 21000 temperature-pressure profiles (TPS files) of the neutral atmosphere derived from Mars Global Surveyor (MGS) radio occultation data....

  13. Modelling of Temperature Profiles and Transport Scaling in Auxiliary Heated Tokamaks

    DEFF Research Database (Denmark)

    Callen, J.D.; Christiansen, J.P.; Cordey, J.G.

    1987-01-01

    in detail: (i) a heat pinch or excess temperature gradient model with constant coefficients; and (ii) a non-linear heat diffusion coefficient (χ) model. Both models predict weak (lesssim20%) temperature profile responses to physically relevant changes in the heat deposition profile – primarily because...... that result from the models clarify why temperature profiles in many tokamaks are often characterized as exhibiting a high degree of 'profile consistency'. Global transport scaling laws are also derived from the two models. The non-linear model with χ ∝ dT/dr produces a non-linear energy confinement time (L......-mode) scaling with input power, . The constant heat pinch or excess temperature gradient model leads to the offset linear law for the total stored energy W with Pin, W = τinc Pin + W(0), which describes JET auxiliary heating data quite well. It also provides definitions for the incremental energy confinement...

  14. Temperature profile data collected from 03 May 1962 to 15 September 1990 (NODC Accession 0000049)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected using bottle casts in a world wide distribution from 03 May 1962 to 15 September 1990. Data were collected and submitted by...

  15. Current profile reconstruction using electron temperature imaging diagnostics

    International Nuclear Information System (INIS)

    Tritz, K.; Stutman, D.; Delgado-Aparicio, L.F.; Finkenthal, M.; Pacella, D.; Kaita, R.; Stratton, B.; Sabbagh, S.

    2004-01-01

    Flux surface shape information can be used to constrain the current profile for reconstruction of the plasma equilibrium. One method of inferring flux surface shape relies on plasma x-ray emission; however, deviations from the flux surfaces due to impurity and density asymmetries complicate the interpretation. Electron isotherm surfaces should correspond well to the plasma flux surfaces, and equilibrium constraint modeling using this isotherm information constrains the current profile. The KFIT code is used to assess the profile uncertainty and to optimize the number, location and SNR required for the Te detectors. As Te imaging detectors we consider tangentially viewing, vertically spaced, linear gas electron multiplier arrays operated in pulse height analysis (PHA) mode and multifoil soft x-ray arrays. Isoflux coordinate sets provided by T e measurements offer a strong constraint on the equilibrium reconstruction in both a stacked horizontal array configuration and a crossed horizontal and vertical beam system, with q 0 determined to within ±4%. The required SNR can be provided with either PHA or multicolor diagnostic techniques, though the multicolor system requires ∼x4 better statistics for comparable final errors

  16. Statistical temperature profile retrievals in clear-air using passive 118-GHz O2 observations

    Science.gov (United States)

    Gasiewski, A. J.; Johnson, J. T.

    1993-01-01

    The clean-air temperature profile accuracy yielded by a localized linear statistical retrieval operator applied to passive aircraft-based 118-GHz spectra is demonstrated. A comparison of the statistically and physically derived correlation coefficients of antenna temperature and kinetic temperature furnishes a physical justification of the statistical retrieval technique. The atmospheric temperature mean and covariance significantly depend on such geophysical parameters as latitude, longitude, local season, and time, as well as the prevailing meteorological state and orographic effects.

  17. A stable algorithm for calculating phase equilibria with capillarity at specified moles, volume and temperature using a dynamic model

    KAUST Repository

    Kou, Jisheng

    2017-09-30

    Capillary pressure can significantly affect the phase properties and flow of liquid-gas fluids in porous media, and thus, the phase equilibrium calculation incorporating capillary pressure is crucial to simulate such problems accurately. Recently, the phase equilibrium calculation at specified moles, volume and temperature (NVT-flash) becomes an attractive issue. In this paper, capillarity is incorporated into the phase equilibrium calculation at specified moles, volume and temperature. A dynamical model for such problem is developed for the first time by using the laws of thermodynamics and Onsager\\'s reciprocal principle. This model consists of the evolutionary equations for moles and volume, and it can characterize the evolutionary process from a non-equilibrium state to an equilibrium state in the presence of capillarity effect at specified moles, volume and temperature. The phase equilibrium equations are naturally derived. To simulate the proposed dynamical model efficiently, we adopt the convex-concave splitting of the total Helmholtz energy, and propose a thermodynamically stable numerical algorithm, which is proved to preserve the second law of thermodynamics at the discrete level. Using the thermodynamical relations, we derive a phase stability condition with capillarity effect at specified moles, volume and temperature. Moreover, we propose a stable numerical algorithm for the phase stability testing, which can provide the feasible initial conditions. The performance of the proposed methods in predicting phase properties under capillarity effect is demonstrated on various cases of pure substance and mixture systems.

  18. Simulation of nitrogen concentration depth profiles in low temperature nitrided stainless steel

    DEFF Research Database (Denmark)

    Christiansen, Thomas; Dahl, Kristian Vinter; Somers, Marcel A. J.

    2006-01-01

    A numerical model is presented, which simulates nitrogen concentration-depth profiles as obtained with low temperature gaseous nitriding of stainless steel. The evolution of the calculated nitrogen concentration-depth profiles is compared with experimental nitriding kinetics. It is shown...

  19. Unprecedentedly Accurate X-Ray Mass Determination for Several Clusters Using Measured Temperature Profiles

    Science.gov (United States)

    Markevitch, Maxim

    1998-01-01

    We use accurate ASCA gas temperature profiles for nearby clusters A3571, A496, A2199 and some others to derive their mass profiles out to radii of overdensity approximately 500. These are relaxed, moderate cooling flow clusters whose two-dimensional temperature maps do not exhibit any structure that would suggest merging activity. Thus the hydrostatic equilibrium assumption should hold for these clusters and meaningful masses can be derived.

  20. Temperature profiles on the gadolinium surface during electron beam evaporation

    International Nuclear Information System (INIS)

    Ohba, Hironori; Shibata, Takemasa

    1995-01-01

    The distributions of surface temperature of gadolinium in a water-cooled copper crucible during electron beam evaporation were measured by optical pyrometry. The surface temperatures were obtained from the radiation intensity ratio of the evaporating surface and a reference light source using Planck's law of radiation. The emitted radiation from the evaporating surface and a reference source was detected by a CCD sensor through a band pass filter of 650 nm. The measured surface temperature generally agreed with those estimated from the deposition rate and the data of the saturated vapor pressure. At high input powers, it was found that the measured value had small difference with the estimated one due to variation of the surface condition. (author)

  1. Effects of temperature on mortality of larval stable fly (Diptera: Muscidae) caused by five isolates of Bacillus thuringiensis.

    Science.gov (United States)

    Lysyk, T J; Selinger, L B

    2012-04-01

    We examined the effects of temperature on mortality of larval stable fly [Stomoxys calcitrans (L.)] caused by Bacillus thuringiensis tolworthi 4L3, B. t. darmastedensis 4M1, B. t. thompsoni 401, B. t. thuringiensis HD2, and B. t. kurstaki HD945. At moderate doses, mortality caused by all isolates ranged from 87 to 99% at 15 degrees C and declined to 29-63% as temperature increased to 30 degrees C. A similar pattern was seen when a higher dose was used, except that the reduction in mortality at warmer temperatures was not as great as was seen with the moderate doses. Insecticidal activity of each isolate against first-instar larvae was reduced by only 5-15% after 5 d in the medium. Mortality of second- and third-instar larvae ranged from 2 to 21%, suggesting the isolates were less effective against larger larvae.

  2. Experimental model of the electron temperature profile in the ionosphere at middle latitudes, (1)

    International Nuclear Information System (INIS)

    Hirao, K.; Oyama, K.

    1980-01-01

    The measurement of the electron temperature profile has been successively carried out at the Kagoshima Space Center by using identical radio frequency rectification probes onboard rockets launched during about half a solar activity cycle. By using about 30 profiles, an experimental model of the electron temperature profile and its solar activity dependency are proposed. Some particular characteristic points, bottom, 170 km, 220 km and topside, are examined in relation to local time and solar activity. The high electron temperature layer which appears at around 11 o'clock local time in winter is pointed out. The differences between the observed electron temperature and the model atmospheric neutral temperature at the characteristic points in particular are examined in relation to solar activity. The relation obtained at topside can be roughly explained by the variation of energy loss of electrons with solar activity. (author)

  3. Temperature changes associated with die profile in axisymmetric ...

    African Journals Online (AJOL)

    Transient heat transfer and temperature change due to varying die opening shapes in a direct extrusion of lead have been numerically investigated and presented. Upper bound method of analysis was used to evaluate the internal heat generation due to plastic deformation and frictional heat at various stages of the ...

  4. Assessments of lake profiling on temperature, Total Suspended ...

    African Journals Online (AJOL)

    Interpolation were performed on temperature, total suspended solid (TSS) and turbidity (TUR) based on in-situ and ex-situ analyses according to the correlation matrix and linear regression at 14 different depths for the Chomor River and Mahadir Island. The result showed outlet significantly decreased over depth caused the ...

  5. Modelling individual temperature profiles from an isolated perfused bovine tongue

    NARCIS (Netherlands)

    Raaymakers, B. W.; Crezee, J.; Lagendijk, J. J.

    2000-01-01

    To predict the temperature distribution during hyperthermia treatments a thermal model that accounts for the thermal effect of blood flow is mandatory. The DIscrete VAsculature (DIVA) thermal model developed at our department is able to do so; geometrically described vessels are handled individually

  6. Calibration and Temperature Profile of a Tungsten Filament Lamp

    Science.gov (United States)

    de Izarra, Charles; Gitton, Jean-Michel

    2010-01-01

    The goal of this work proposed for undergraduate students and teachers is the calibration of a tungsten filament lamp from electric measurements that are both simple and precise, allowing to determine the temperature of tungsten filament as a function of the current intensity. This calibration procedure was first applied to a conventional filament…

  7. Influence of absorbed pump profile on the temperature distribution ...

    Indian Academy of Sciences (India)

    2017-01-20

    Jan 20, 2017 ... the energy is eventually turned into heat consumption. [9–17]. The temperature distribution in the laser rod is determined by the non-uniform distribution of the absorbed pump and the cooling arrangement. The radial heat dissipation creates thermal effects such as thermal induced birefringence and thermal ...

  8. Molecular diffusion of stable water isotopes in polar firn as a proxy for past temperatures

    Science.gov (United States)

    Holme, Christian; Gkinis, Vasileios; Vinther, Bo M.

    2018-03-01

    Polar precipitation archived in ice caps contains information on past temperature conditions. Such information can be retrieved by measuring the water isotopic signals of δ18O and δD in ice cores. These signals have been attenuated during densification due to molecular diffusion in the firn column, where the magnitude of the diffusion is isotopologue specific and temperature dependent. By utilizing the differential diffusion signal, dual isotope measurements of δ18O and δD enable multiple temperature reconstruction techniques. This study assesses how well six different methods can be used to reconstruct past surface temperatures from the diffusion-based temperature proxies. Two of the methods are based on the single diffusion lengths of δ18O and δD , three of the methods employ the differential diffusion signal, while the last uses the ratio between the single diffusion lengths. All techniques are tested on synthetic data in order to evaluate their accuracy and precision. We perform a benchmark test to thirteen high resolution Holocene data sets from Greenland and Antarctica, which represent a broad range of mean annual surface temperatures and accumulation rates. Based on the benchmark test, we comment on the accuracy and precision of the methods. Both the benchmark test and the synthetic data test demonstrate that the most precise reconstructions are obtained when using the single isotope diffusion lengths, with precisions of approximately 1.0 °C . In the benchmark test, the single isotope diffusion lengths are also found to reconstruct consistent temperatures with a root-mean-square-deviation of 0.7 °C . The techniques employing the differential diffusion signals are more uncertain, where the most precise method has a precision of 1.9 °C . The diffusion length ratio method is the least precise with a precision of 13.7 °C . The absolute temperature estimates from this method are also shown to be highly sensitive to the choice of fractionation factor

  9. Thermally Stable Mesoporous Perovskite Solar Cells Incorporating Low-Temperature Processed Graphene/Polymer Electron Transporting Layer.

    Science.gov (United States)

    Tong, Shi Wun; Balapanuru, Janardhan; Fu, Deyi; Loh, Kian Ping

    2016-11-02

    In the short time since its discovery, perovskite solar cells (PSCs) have attained high power conversion efficiency but their lack of thermal stability remains a barrier to commercialization. Among the experimentally accessible parameter spaces for optimizing performance, identifying an electron transport layer (ETL) that forms a thermally stable interface with perovskite and which is solution-processable at low-temperature will certainly be advantageous. Herein, we developed a mesoporous graphene/polymer composite with these advantages when used as ETL in CH 3 NH 3 PbI 3 PSCs, and a high efficiency of 13.8% under AM 1.5G solar illumination could be obtained. Due to the high heat transmission coefficient and low isoelectric point of mesoporous graphene-based ETL, the PSC device enjoys good chemical and thermal stability. Our work demonstrates that the mesoporous graphene-based scaffold is a promising ETL candidate for high performance and thermally stable PSCs.

  10. Retrieving Temperature and Moisture Profiles from AERI Radiance Observations. AERIPROF Value-Added Product Technical Description

    Energy Technology Data Exchange (ETDEWEB)

    Feltz, W. F. [Univ. of Wisconsin, Madison, WI (United States); Howell, H. B. [Univ. of Wisconsin, Madison, WI (United; Knuteson, R. O. [Univ. of Wisconsin, Madison, WI (United States); Comstock, J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Mahon, R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Turner, D. D. [National Oceanic and Atmospheric Administration (NOAA), Boulder, CO (United States); Smith, W. L. [NASA Langley Research Center, Hampton, VA (United States); Woolf, H. M. [Univ. of Wisconsin, Madison, WI (United; Sivaraman, C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Halter, T. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2007-04-01

    One of the goals of the Atmospheric Radiation Measurement (ARM) Program is to collect a long-term series of radiative and atmospheric state observations to improve the parameterization of these processes in global climate models. The ARM Program intended to move away from the traditional approach of directly measuring profiles of temperature and moisture using radiosondes, which is expensive in terms of expendables and manpower, and develop methods to retrieve these profiles with ground-based remote sensors. The atmospheric emitted radiance interferometer (AERI), whose radiance data contains information on the vertical distribution of water vapor and temperature, is an integral part of the ARM profiling plan.

  11. Relationship between tolerance factor and temperature coefficient of permittivity of temperature-stable high permittivity BaTiO3–Bi(MeO3 compounds

    Directory of Open Access Journals (Sweden)

    Natthaphon Raengthon

    2016-03-01

    Full Text Available The temperature coefficient of permittivity (TCε of BaTiO3–Bi(MeO3 solid solutions were investigated. It was determined that as the tolerance factor was decreased with the addition of Bi(MeO3, the TCε shifted from large negative values to TCε values approaching zero. It is proposed that the different bonding nature of the dopant cation affects the magnitude and temperature stability of the permittivity. This study suggests that the relationship between tolerance factor and TCε can be used as a guide to design new dielectric compounds exhibiting temperature-stable high permittivity characteristics, which is similar to past research on perovskite and pyrochlore-based microwave dielectrics.

  12. Dynamic measurements of depth profiles of hydrogen implanted into graphite at elevated temperatures

    International Nuclear Information System (INIS)

    Morita, K.; Ohtsuka, K.; Hasebe, Y.

    1989-01-01

    Time variations of depth profiles of hydrogen retained in graphite during and after implantation of 3 keV H 2 + ions have been studied from dynamic measurements by means of elastic recoil detection at temperatures between 300 and 1000 K and at ion fluxes of 4x10 13 , 2x10 14 and 4x10 14 /cm 2 s. It is shown that the maximum steady state concentration of hydrogens is about 6x10 22 /cm 3 at room temperature and is by a factor of 1.7 higher than the maximum static concentration after implantation. It is also shown that the depth profiles have the maximum at the projected range of implanted ions, the width of the profile broadens gradually inwards as the fluence and the temperature increase and the shapes of steady state profiles are almost the same as those of static profiles. By analytically solving mass balance equations for hydrogens, in which diffusion, trapping, ion-induced detrapping and recession of the surface are taken into account, the experimental steady state depth profiles are demonstrated to be well reproduced. The diffusion constants of hydrogen are determined as a function of temperature by fitting the calculated to the experimental depth profiles. (orig.)

  13. Ion temperature profiles in the horns of the plasma sheet

    Science.gov (United States)

    Suszcynsky, D. M.; Gosling, J. T.; Thomsen, M. F.

    1993-01-01

    The plasma sheet horns are the low-altitude extensions of the plasma sheet that lie poleward of the plasmasphere and equatorward of the tail lobes. Within the horns, magnetic field lines of increasing geomagnetic latitudes map to increasing distances into the downtail plasma sheet. Plasma data from the fast plasma experiment on ISEE 2 have been analyzed for 11 outbound crossings of the horns in the premidnight sector of the magnetosphere at typical altitudes of 2-4 R(E). These crossings typically occurred on time scales of less than 1 hour, providing almost instantaneous snapshots of plasma gradients within the horns. Ion temperatures observed during these crossings generally decreased by a factor of four to eight as magnetic field lines of increasing geomagnetic latitude were traversed. If we make the reasonable assumption that the ion temperatures are constant along the field lines within the plasma sheet, then this result implies that the ion temperatures in the downtail plasma sheet also commonly decrease by this same factor over the radial range extending from the inner edge of the plasma sheet at the plasmapause boundary to the outer edge at a neutral line in the distant tail.

  14. Ion temperature profile measurements using the far line wings of Hα

    International Nuclear Information System (INIS)

    Bengtson, R.D.; Boedo, J.; Rowan, W.L.

    1986-01-01

    This paper presents ion temperature profiles for the outer half of the TEXT plasma using the Doppler broadened far line wings of the H α line profile. The technique depends on the assumption that the hydrogen neutrals have equilibrated with the ions through charge exchange collisions. Data reduction depends upon going far enough out on the line wing that the intensity profile is characteristic of the hottest portion of the plasma along the line of sight, thus removing the need for an inversion procedure. A Fabry-Perot interferometer is used to measure the line profiles because of its superior instrumental profile. This technique is compared with the charge exchange technique and Doppler broadening of impurities. The application to ion temperature measurements using a diagnostic neutral beam is also discussed

  15. Plasma Protein Turnover Rates in Rats Using Stable Isotope Labeling, Global Proteomics, and Activity-Based Protein Profiling

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Jordan N.; Tyrrell, Kimberly J.; Hansen, Joshua R.; Thomas, Dennis G.; Murphree, Taylor A.; Shukla, Anil K.; Luders, Teresa; Madden, James M.; Li, Yunying; Wright, Aaron T.; Piehowski, Paul D.

    2017-12-06

    Protein turnover is important for general health on cellular and organism scales providing a strategy to replace old, damaged, or dysfunctional proteins. Protein turnover also informs of biomarker kinetics, as a better understanding of synthesis and degradation of proteins increases the clinical utility of biomarkers. Here, turnover rates of plasma proteins in rats were measured in vivo using a pulse-chase stable isotope labeling experiment. During the pulse, rats (n=5) were fed 13C6-labeled lysine (“heavy”) feed for 23 days to label proteins. During the chase, feed was changed to an unlabeled equivalent feed (“light”), and blood was repeatedly sampled from rats over 10 time points for 28 days. Plasma samples were digested with trypsin, and analyzed with liquid chromatography-tandem mass spectrometry (LC-MS/MS). MaxQuant was used to identify peptides and proteins, and quantify heavy:light lysine ratios. A system of ordinary differential equations was used to calculate protein turnover rates. Using this approach, 273 proteins were identified, and turnover rates were quantified for 157 plasma proteins with half-lives ranging 0.3-103 days. For the ~70 most abundant proteins, variability in turnover rates among rats was low (median coefficient of variation: 0.09). Activity-based protein profiling was applied to pooled plasma samples to enrich serine hydrolases using a fluorophosphonate (FP2) activity-based probe. This enrichment resulted in turnover rates for an additional 17 proteins. This study is the first to measure global plasma protein turnover rates in rats in vivo, measure variability of protein turnover rates in any animal model, and utilize activity-based protein profiling for enhancing measurements of targeted, low-abundant proteins, such as those commonly used as biomarkers. Measured protein turnover rates will be important for understanding of the role of protein turnover in cellular and organism health as well as increasing the utility of protein

  16. Temperature and age affect the life history characteristics and fatty acid profiles of Moina macrocopa (Cladocera)

    NARCIS (Netherlands)

    Gama-Flores, José Luis; Huidobro-Salas, María Elena; Sarma, S.S.S.; Nandini, S.; Zepeda-Mejia, Ricardo; Gulati, Ramesh D.

    2015-01-01

    Demographic responses and fatty acid profiles of Moina macrocopa were quantified under different temperature regimes (20 °C, 25 °C and 30 °C and diurnally variable 20–30 °C) and at fixed ration (10.65 µg DW ml−1) of Chlorella. Highest constant temperature (30 °C) reduced the density of M. macrocopa.

  17. High-temperature stable absorber coatings for linear concentrating solar thermal power plants; Hochtemperaturstabile Absorberschichten fuer linear konzentrierende solarthermische Kraftwerke

    Energy Technology Data Exchange (ETDEWEB)

    Hildebrandt, Christina

    2009-03-23

    This work describes the development of new absorber coatings for different applications - para-bolic trough and linear Fresnel collectors - and operating conditions - absorber in vacuum or in air. The demand for higher efficiencies of solar thermal power plants using parabolic trough technology results in higher temperatures in the collectors and on the absorber tubes. As heat losses increase strongly with increasing temperatures, the need for a lower emissivity of the absorber coating at constant absorptivity arises. The linear Fresnel application envisions ab-sorber tubes stable in air at high temperatures of about 450 C, which are to date commercially not available. This work comprises the theoretical background, the modeling and the fabrication of absorber tubes including the technology transfer to a production-size inline sputter coater. In annealing tests and accompanying optical measurements, degradation processes have been observed and specified more precisely by material characterization techniques. The simulations provided the capability of different materials used as potential IR-reflector. The highest selectivity can be achieved by applying silver which consequently has been chosen for the application in absorber coatings of the parabolic trough technology. Thin silver films how-ever need to be stabilized when used at high temperatures. Appropriate barrier layers as well as process and layer parameters were identified. A high selectivity was achieved and stability of the absorber coating for 1200 h at 500 C in vacuum has been demonstrated. For the application in air, silver was also analyzed as a potential IR-reflector. Even though the stability could be increased considerably, it nevertheless proved to be insufficient. The main factors influencing stability in a positive way are the use of higher quality polishing, additional barrier layers and adequate process parameters. This knowledge was applied for developing coatings which are stable in air at

  18. Method of preparing high-temperature-stable thin-film resistors

    International Nuclear Information System (INIS)

    Raymond, L.S.

    1983-01-01

    A chemical vapor deposition method is disclosed for manufacturing tungsten-silicide thin-film resistors of predetermined bulk resistivity and temperature coefficient of resistance (TCR). Gaseous compounds of tungsten and silicon are decomposed on a hot substrate to deposit a thin-film of tungsten-silicide. The TCR of the film is determined by the crystallinity of the grain structure, which is controlled by the temperature of deposition and the tungsten to silicon ratio. The bulk resistivity is determined by the tungsten to silicon ratio. Manipulation of the fabrication parameters allows for sensitive control of the properties of the resistor

  19. Method of preparing high-temperature-stable thin-film resistors

    Science.gov (United States)

    Raymond, L.S.

    1980-11-12

    A chemical vapor deposition method for manufacturing tungsten-silicide thin-film resistors of predetermined bulk resistivity and temperature coefficient of resistance (TCR) is disclosed. Gaseous compounds of tungsten and silicon are decomposed on a hot substrate to deposit a thin-film of tungsten-silicide. The TCR of the film is determined by the crystallinity of the grain structure, which is controlled by the temperature of deposition and the tungsten to silicon ratio. The bulk resistivity is determined by the tungsten to silicon ratio. Manipulation of the fabrication parameters allows for sensitive control of the properties of the resistor.

  20. Evidence for Stable High Temperature Ferromagnetism in Fluorine Treated C60

    Science.gov (United States)

    2013-01-01

    dimensional polymeric form of C60 produced by high pressure (6 GPa) and high temperature in the vicinity of 1000 K.2,3,4 It is known that C60 when...heat treatment in the presence of iodine was shown to be ferromagnetic having a Curie temperature of 60 K 8,9 Doping with a mix of iodine and bromine...a chilled slide on the top which enabled collection of the condensed vapor . The Raman spectra of the material condensed on the slide is shown at the

  1. Equilibrium Temperature Profiles within Fission Product Waste Forms

    Energy Technology Data Exchange (ETDEWEB)

    Kaminski, Michael D. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-10-01

    We studied waste form strategies for advanced fuel cycle schemes. Several options were considered for three waste streams with the following fission products: cesium and strontium, transition metals, and lanthanides. These three waste streams may be combined or disposed separately. The decay of several isotopes will generate heat that must be accommodated by the waste form, and this heat will affect the waste loadings. To help make an informed decision on the best option, we present computational data on the equilibrium temperature of glass waste forms containing a combination of these three streams.

  2. QBO effects manifesting in ozone, temperature, and wind profiles

    OpenAIRE

    Sitnov, S. A.

    2004-01-01

    On the basis of ozonesonde records up to 1998 the responses on the equatorial quasi-biennial oscillation (QBO), manifesting in ozone, temperature, and wind (QBO effects) were isolated in the region from the ground to altitudes as high as 35km at 22 stations located in Europe (7), North America (7), Japan (4), Hawaii (1), Australia (2), and Antarctic (1).

    The vertical structures of the QBO effects of ozone are represented as an alternati...

  3. A lidar system for measuring atmospheric pressure and temperature profiles

    Science.gov (United States)

    Schwemmer, Geary K.; Dombrowski, Mark; Korb, C. Laurence; Milrod, Jeffry; Walden, Harvey

    1987-01-01

    The design and operation of a differential absorption lidar system capable of remotely measuring the vertical structure of tropospheric pressure and temperature are described. The measurements are based on the absorption by atmospheric oxygen of the spectrally narrowband output of two pulsed alexandrite lasers. Detailed laser output spectral characteristics, which are critical to successful lidar measurements, are presented. Spectral linewidths of 0.026 and 0.018 per cm for the lasers were measured with over 99.99 percent of the energy contained in three longitudinal modes.

  4. Variability in lipid profile among patients presented with acute myocardial infarction, unstable angina and stable angina pectoris.

    Science.gov (United States)

    Yang, N; Feng, J-P; Chen, G; Kou, L; Li, Y; Ren, P; Zhao, L-L; Qin, Q

    2014-01-01

    Despite the amply evidence and guidelines in treating coronary artery disease (CAD) with lipid-lowering therapy, physicians still have concerns in treating acute myocardial infarction (AMI) patients who have the low serum lipid level. We explored the adequacy of lipid-lowering therapy in treating AMI patients. Over 3000 CAD lipid profile data were collected, their data were divided into 3 groups (AMI; stable angina pectoris (SAP) and unstable angina pectoris (UAP) group) based their clinical characteristics. Statistical analyses were performed to compare their baseline lipid levels and clinical feature. The total cholesterol (TC), low-density lipoprotein cholesterol (LDL-c) and high-density lipoprotein cholesterol (HDL-c) level in AMI patients were the lowest, followed by UAP patient group and SAP patient group. There were significant differences in white blood count (WBC) and ejection fraction (EF) between 3 groups. A good correlation was confirmed between EF% and the lipid parameters of TC, LDL-c, HDL-c, non-HDL-c. WBC did not correlate with the lipid except HDL-c. AMI is an acute inflammatory reaction that is accompanied with the change of lipid level. Although the level of TC, LDL-c and HDL-c are lower in AMI, but it is related with acute inflammatory reaction during the rupture of atherosclerotic plaques. Lipid-lowering therapy should not be delayed in treating AMI patients with lower lipid level.

  5. FATTY ACID PROFILE IN MILK OF BOVEC SHEEP FED IN THE STABLE OR GRAZED IN DIFFERENT PASTURES

    Directory of Open Access Journals (Sweden)

    Angela Cividini

    2015-09-01

    Full Text Available The fatty acid profile in the milk of Bovec sheep fed total mixed ratio (TMR and grazed natural pastures in the lowland (480 m altitude supplemented with the second harvest (L as well as grazed different altitude mountain pastures; M1 (1100- 1300 m altitude, M2 (1600-1700 m altitude, M3 (1800 m altitude, M4 (1900 m altitude, M5 (2200 m altitude were determined. There was an important effect when ewes were turned from the stable to the pasture on all fatty acids. The percentage of α-linolenic acid (ALA, arachidonic acid (ARA and docosahexaenoic acid (DHA increased significantly (P<0.001 with the diet. In the milk from M5 grazing the percentage of ALA was 2.5 times higher than in milk from L and 2.6 times higher than in milk from TMR. The percentage of ARA and DHA in milk was the highest when ewes were grazing on the M5 pasture (0.21±0.02 wt. %; 0.22±0.02 wt. % respectively. Total n-3PUFA and n-6PUFA increased significantly (P<0.001 by the diet. Therefore, the n-6/n-3PUFA ratio was the best (1.2 in milk produced in the highest mountain pasture (M5, in terms of nutritional requirements.

  6. Carbon stable isotope analysis as a tool for tracing temperature during the El Tremedal underground coal gasification at great depth

    Energy Technology Data Exchange (ETDEWEB)

    Brasseur, A.; Antenucci, D.; Bouquegneau, J.-M.; Coeme, A.; Dauby, P.; Letolle, R.; Mostade, M.; Pirlot, P.; Pirard, J.-P. [Universite de Liege, Liege (Belgium). Laboratoire de Genie Chimique, Institut de Chimie

    2002-01-01

    The new opportunity given by the underground gasifier developed at Alcorisa in Spain (Province of Teruel) in the framework of an European experiment has promoted a better understanding of gasification in a natural reactor. The thermodynamical equilibria of gasification reactions and the repartition of the stable isotopes of carbon ({sup 13}C/{sup 12}C) in the produced gases have been used to monitor the process. An estimation of the temperatures inside the gasifier and at the exhaust gas been performed. As shown by the isotopic balances, the tar formation is negligible or null and the pyrolysis zone spreads continuously. The study has confirmed the reality of the {sup 13}C isotopic abundance measurements for the system CO/CO{sub 2} as an indicator of the temperature inside the gasifier. During the gasifier expansion, the temperature at the exhaust decreases whereas the temperature inside the gasifier is practically constant showing a slight increasing trend. As pointed out by the data, the oxygen enrichment of the gasifying agent plays an important role on the estimated temperatures. 19 refs., 4 figs., 5 tabs.

  7. In vivo metabolic flux profiling with stable isotopes discriminates sites and quantifies effects of mitochondrial dysfunction in C. elegans

    Science.gov (United States)

    Ostrovsky, Julian; Clarke, Colleen; Preston, Judith; Bennett, Michael J.; Yudkoff, Marc; Xiao, Rui; Falk, Marni J.

    2014-01-01

    Mitochondrial respiratory chain (RC) disease diagnosis is complicated both by an absence of biomarkers that sufficiently divulge all cases and limited capacity to quantify adverse effects across intermediary metabolism. We applied high performance liquid chromatography (HPLC) and mass spectrometry (MS) studies of stable-isotope based precursor–product relationships in the nematode, C. elegans, to interrogate in vivo differences in metabolic flux among distinct genetic models of primary RC defects and closely related metabolic disorders. Methods C. elegans strains studied harbor single nuclear gene defects in complex I, II, or III RC subunits (gas-1, mev-1, isp-1); enzymes involved in coenzyme Q biosynthesis (clk-1), the tricarboxylic acid cycle (TCA, idh-1), or pyruvate metabolism (pdha-1); and central nodes of the nutrient-sensing signaling network that involve insulin response (daf-2) or the sirtuin homologue (sir-2.1). Synchronous populations of 2000 early larval stage worms were fed standard Escherichia coli on nematode growth media plates containing 1,6-13C2-glucose throughout their developmental period, with samples extracted on the first day of adult life in 4% perchloric acid with an internal standard. Quantitation of whole animal free amino acid concentrations and isotopic incorporation into amino and organic acids throughout development was performed in all strains by HPLC and isotope ratio MS, respectively. GC/MS analysis was also performed to quantify absolute isotopic incorporation in all molecular species of key TCA cycle intermediates in gas-1 and N2 adult worms. Results Genetic mutations within different metabolic pathways displayed distinct metabolic profiles. RC complex I (gas-1) and III (isp-1) subunit mutants, together with the coenzyme Q biosynthetic mutant (clk-1), shared a similar amino acid profile of elevated alanine and decreased glutamate. The metabolic signature of the complex II mutant (mev-1) was distinct from that of the other RC

  8. Protein Profile of Mozzarella Cheese Produced with Treatment of Coagulation and Stretching Temperature Combination

    Directory of Open Access Journals (Sweden)

    Purwadi Purwadi

    2012-04-01

    Full Text Available A research used lime juice as acidifier in the making of Mozzarella cheese was aimed to learn the protein profile produced with treatment of coagulation stretching temperature combination. The method used in this research was factorial experiment of 4 x 4, the first factor was coagulation temperature (G : G1 = 30 oC, G2 = 35 oC, G3 = 40 oC, and G4 = 45 oC, and the second factor was stretching temperature (M : M1 = 70 oC, M2 = 75 oC, M3 = 80 oC, and M4 = 85oC. Combination of coagulation temperature 30 and 35oC with different stretching temperatures 70, 75, 80, and 85 oC, gave the same protein electroforegram, but the combination of coagulation temperature 30 and 35 oC and coagulation temperatur 40 and 45 oC with different stretching temperature gave different protein electroforegram. From this experiment, its could be concluded that the treatment of coagulation temperature 30 oC with stretching temperature 75 oC is the best treatment. Keywords: protein profile, Mozzarella cheese, coagulation temperature, stretching temperature

  9. The temperature profile of an apple supply chain: A case study of the Ceres district

    Directory of Open Access Journals (Sweden)

    A.G. Du Toit Valentine

    2017-01-01

    Full Text Available Background: There is a logistical gap in the first section of the apple supply chain that affects the temperature profiles of apples further downstream in the supply chain. Objectives: This article’s main objective is to confirm whether the logistics processes, in terms of the temperature profile of apples for the first 48 hours post-harvest, have an influence on the yield and/or quality of the fruit. Method: Observations were made and informal interviews were conducted on three different farms to ascertain their perspective of the first section of the supply chain. Temperature trials were conducted to analyse the temperature profile of two apple varieties, namely Golden Delicious and Granny Smith on three different farms. These trials were conducted by placing an iButton® device on the inside and outside of an apple to measure the temperature readings every minute for the first 48 hours after picking. Results: The research identified that it is not only at what time the apples are being harvested, but also at what time the apples are placed under cooling conditions to remove the field heat to obtain the recommended temperature profile within 48 hours. In addition, it was determined that effective and efficient picking at the right time (especially between 07:00 and 09:00 and the transportation of the apples directly, or as soon as possible after the apples came out of the orchard to the centralised cold storage facility, are key in ensuring the quality of the fruit and the temperature profile necessary for export. Conclusion: This article identifies the need to improve operational procedures along the cold chain. From this research, it is clear that there are problem areas that affect the temperature profile of apples.

  10. The temperature profile of an apple supply chain: A case study of the Ceres district

    Directory of Open Access Journals (Sweden)

    A.G. Du Toit Valentine

    2017-01-01

    Full Text Available Background: There is a logistical gap in the first section of the apple supply chain that affects the temperature profiles of apples further downstream in the supply chain.Objectives: This article’s main objective is to confirm whether the logistics processes, in terms of the temperature profile of apples for the first 48 hours post-harvest, have an influence on the yield and/or quality of the fruit.Method: Observations were made and informal interviews were conducted on three different farms to ascertain their perspective of the first section of the supply chain. Temperature trials were conducted to analyse the temperature profile of two apple varieties, namely Golden Delicious and Granny Smith on three different farms. These trials were conducted by placing an iButton® device on the inside and outside of an apple to measure the temperature readings every minute for the first 48 hours after picking.Results: The research identified that it is not only at what time the apples are being harvested, but also at what time the apples are placed under cooling conditions to remove the field heat to obtain the recommended temperature profile within 48 hours. In addition, it was determined that effective and efficient picking at the right time (especially between 07:00 and 09:00 and the transportation of the apples directly, or as soon as possible after the apples came out of the orchard to the centralised cold storage facility, are key in ensuring the quality of the fruit and the temperature profile necessary for export.Conclusion: This article identifies the need to improve operational procedures along the cold chain. From this research, it is clear that there are problem areas that affect the temperature profile of apples. 

  11. QBO effects manifesting in ozone, temperature, and wind profiles

    Directory of Open Access Journals (Sweden)

    S. A. Sitnov

    2004-04-01

    Full Text Available On the basis of ozonesonde records up to 1998 the responses on the equatorial quasi-biennial oscillation (QBO, manifesting in ozone, temperature, and wind (QBO effects were isolated in the region from the ground to altitudes as high as 35km at 22 stations located in Europe (7, North America (7, Japan (4, Hawaii (1, Australia (2, and Antarctic (1. The vertical structures of the QBO effects of ozone are represented as an alternation of layers of well-developed quasi-biennial signals, whose phases gradually change with height and thin transitional layers of ill-developed signals, whose phases change abruptly with height. The amplitudes of the effects depend on height and reach the maxima of 3–6nbar in the lower stratosphere. At the majority of sites the effects are found to be approximately in phase between 20 and 23km. Two types of the vertical structures of the temperature QBO effects are found. At most of the sites located equatorward of about 50° the stratospheric temperature anomalies are characterized by downward propagation, whereas at sites situated poleward of about 50° they look as column-like structures. Near the tropopause the effects frequently reveal dipole-like structure, when the stratospheric and tropospheric anomalies are of opposite signs. The amplitudes of the effects are in the range of 0.5–1°C. The vertical structures of the QBO effects of horizontal wind components reveal a diversity of patterns. The amplitudes of the QBO effects of the meridional and zonal winds are comparable and lie in the range of 0.5–2m s–1. As a rule, the maxima of the effects are noticed slightly below the tropopause, as well as in the middle stratosphere. In general, a statistical assurance of the obtained QBO effects is rather poor. However, a considerable part of them reveal similarity, which can be hardly explained by chance. Furthermore, the results agree with possible physical mechanisms of off-equatorial influence of the QBO, as well

  12. Stable and low contact resistance electrical contacts for high temperature SiGe thermoelectric generators

    KAUST Repository

    Zhang, Bo

    2018-04-14

    The thermal stability and contact resistance of TaAlN thin films as electrical contacts to SiGe thermoelectric elements are reported. We demonstrate that a sharp interface is maintained after the device annealed at 800°C for over 100h, indicating that no interdiffusion takes place between TaAlN and SiGe. A specific contact resistivity of (2.1±1.3)×10−6Ω-cm2 for p-type SiGe and (2.8±1.6)×10−5 Ω-cm2 for n-type SiGe is demonstrated after the high temperature annealing. These results show that TaAlN is a promising contact material for high temperature thermoelectrics such as SiGe.

  13. Refractive index and temperature sensing in anisotropic silver nanostructures with stable photo-physical properties

    Science.gov (United States)

    Biswas, Subrata; Kumbhakar, Pathik

    2018-01-01

    In this report, we have demonstrated the refractive index and temperature-sensing abilities of polyvinylpyrrolidone (PVP)-protected silver nanostructures of triangular, connected and plate-like shapes. Interestingly, these nanostructures even after 2 and ½ years of syntheses showed plasmonic-sensing ability of temperature in the temperature range of 283-333 K. Also, refractive index (R.I.) sensing has been demonstrated in the aged samples and obtained the highest R.I. sensitivity of 306 nm/RIU in one of the sample. The synthesized samples have been kept in dark (inside desiccators) intentionally for the extended period of 2 and ½ years after synthesis and monitored intermittently their UV-Vis absorption and photoluminescence (PL) emission characteristics to check the functionally of the aged silver nanostructures. It has been found the samples remain well dispersed in different solvents and can forbid agglomeration even in 0.25 M NaCl solution. We have also demonstrated here fabrication of a flexible and transparent thin film of the synthesized samples in polyvinyl alcohol (PVA) matrix and investigated its low power continuous-wave (CW) nonlinear optical properties using spatial self-phase modulation (SSPM) technique. The nonlinear refractive index ( n 2) value of the film has been determined to be 5.6 × 10- 6 cm2/W at the He-Ne laser wavelength of 632.8 nm. In this report we have demonstrated temperature and R.I. sensing and also it has been demonstrated that the synthesized samples remain functional even after 2 and ½ years of synthesis. Also, samples may find potential applications in nonlinear optical phase modulation devices.

  14. Large polarization gradients and temperature-stable responses in compositionally-graded ferroelectrics

    Science.gov (United States)

    Damodaran, Anoop R.; Pandya, Shishir; Qi, Yubo; Hsu, Shang-Lin; Liu, Shi; Nelson, Christopher; Dasgupta, Arvind; Ercius, Peter; Ophus, Colin; Dedon, Liv R.; Agar, Josh C.; Lu, Hongling; Zhang, Jialan; Minor, Andrew M.; Rappe, Andrew M.; Martin, Lane W.

    2017-05-01

    A range of modern applications require large and tunable dielectric, piezoelectric or pyroelectric response of ferroelectrics. Such effects are intimately connected to the nature of polarization and how it responds to externally applied stimuli. Ferroelectric susceptibilities are, in general, strongly temperature dependent, diminishing rapidly as one transitions away from the ferroelectric phase transition (TC). In turn, researchers seek new routes to manipulate polarization to simultaneously enhance susceptibilities and broaden operational temperature ranges. Here, we demonstrate such a capability by creating composition and strain gradients in Ba1-xSrxTiO3 films which result in spatial polarization gradients as large as 35 μC cm-2 across a 150 nm thick film. These polarization gradients allow for large dielectric permittivity with low loss (εr~775, tan δ<0.05), negligible temperature-dependence (13% deviation over 500 °C) and high-dielectric tunability (greater than 70% across a 300 °C range). The role of space charges in stabilizing polarization gradients is also discussed.

  15. Manufacturing and Characterization of Temperature-Stable, Novel, Viscoelastic Polyurea Based Foams for Impact Management

    Science.gov (United States)

    Ramirez, Brian Josue

    The aim of this thesis was to develop advance, high performance polyurea foams for multi-hit capability in protective equipment that respond over a range of impact energies, temperatures, and strain rates. In addition, the microstructure of these materials should be tunable such that the peak stress (or force) transmitted across the foam section can be limited to a specific value defined by an injury threshold while maximizing impact energy absorption. Novel polyurea foams were manufactured and found to exhibit a reversible viscoelastic shear deformation at the molecular level. The intrinsic shear dissipation process is synergistically coupled to controlled collapse of a novel pore structure. The microstructure compromises of stochastic polyhedral cells ranging from 200 - 500 mum with perforated membranes with small apertures ( 20 mum). This makes them strain rate sensitive as the rate at which the air escapes the cells depend upon the loading rate. These mechanisms operate simultaneously and sequentially, thereby significantly reducing the transmitted impact forces across the foam section. Thus, they behave as an elastically modulated layered composite because the cells stiffen or soften in response to the changing loading rate. Therefore, the newly developed polyurea foams are able to manage the varying material strain rate that occurs within the same loading event without the need to modulate the stiffness or density. Additionally, polyurea foams were found to retain its excellent impact properties over a range of temperatures (0°C to 40°C) by having a glass transition temperature well below 0°C. This is in contrast to commercially available high performance foams that have the glass transition temperature near 0°C and absorb energy through phase transformation at ambient conditions, but significantly stiffen at lower temperatures, and dramatically soften at higher temperatures. This expands the application domain of polyurea foam material considerably as it

  16. Ion temperature profiles on TJ-II stellarator during NBI plasma heating

    International Nuclear Information System (INIS)

    Balbin, R.; Fontdecaba, J.M.; McCarthy, K.J.; Carmona, J.M.; Guasp, J.; Liniers, M.; Fuentes, C.; Castejon, F.; Petrov, S.

    2005-01-01

    The ion temperature of plasmas in the TJ-II flexible heliac has been measured using two Acord-12 neutral particle analysers. These analysers can scan the plasma poloidally to obtain ion temperature profiles. The measurements presented were performed during NBI plasma heating three similar magnetic configurations whose volume inside their last closed flux surface is about 1 m 3 and whose effective minor radius is 0.20 m. In addition, their rotational transform at the centre varies from 1.49 to 1.7. Also, for the configurations studied the rotational transform increases slightly from the centre to the edge, since TJ-II is an almost shearless device, without giving rise to magnetic islands inside the plasma volume. The plasmas studied were created in hydrogen using two gyrotrons having a total power of about 400 kW. The pulse duration was 250 ms and the power deposition profile was off-axis in two of the configurations. In the other configuration the power deposition profile was on-axis. In these discharges ∼350 kW of neutral beam injection (30 keV, 150 ms) was used for additional plasma heating. These plasmas were characterized by a strong increase in plasma density during the NBI pulse and by the high fraction of power absorbed by the electrons. As shown previously, the ion temperature profile is flat in ECRH plasmas created in the TJ-II. In these new studies, this profile remains flat during part of the ECRH+NBI stage. Both of theses stages are distinguished by low density (n e ≤ 8 x 10 18 m -3 ) and highly peaked electron temperature profiles. During the high-density ECRH+NBI stage the plasmas have low electron temperatures while the ion temperature profile changes from flat to peaked. This result suggests that NBI heating occurs within the ρ = 0.5 effective radius. (author)

  17. [Startup, stable operation and process failure of EBPR system under the low temperature and low dissolved oxygen condition].

    Science.gov (United States)

    Ma, Juan; Li, Lu; Yu, Xiao-Jun; Wei, Xue-Fen; Liu, Juan-Li

    2015-02-01

    A sequencing batch reactor (SBR) was started up and operated with alternating anaerobic/oxic (An/O) to perform enhanced biological phosphorus removal (EBPR) under the condition of 13-16 degrees C. The results showed that under the condition of low temperature, the EBPR system was successfully started up in a short time (<6 d). The reactor achieved a high and stable phosphorus removal performance with an influent phosphate concentration of 20 mg x L(-1) and the dissolved oxygen (DO) concentration of 2 mg x L(-1). The effluent phosphate concentration was lower than 0.5 mg x L(-1). It was found that decreasing DO had an influence on the steady operation of EBPR system. As DO concentration of aerobic phase decreased from 2 mg x L(-1) to 1 mg x L(-1), the system could still perform EBPR and the phosphorus removal efficiency was greater than 97.4%. However, the amount of phosphate released during anaerobic phase was observed to decrease slightly compared with that of 2 mg x L(-1) DO condition. Moreover, the phosphorus removal performance of the system deteriorated immediately and the effluent phosphate concentration couldn't meet the national integrated wastewater discharge standard when DO concentration was further lowered to 0.5 mg x L(-1). The experiments of increasing DO to recover phosphorus removal performance of the EBPR suggested the process failure resulted from low DO was not reversible in the short-term. It was also found that the batch tests of anoxic phosphorus uptake using nitrite and nitrate as electron acceptors had an impact on the stable operation of EBPR system, whereas the resulting negative influence could be recovered within 6 cycles. In addition, the mixed liquid suspended solids (MLSS) of the EBPR system remained stable and the sludge volume index (SVI) decreased to a certain extend in a long run, implying long-term low temperature and low DO condition favored the sludge sedimentation.

  18. Algorithm Development for Multi-Energy SXR based Electron Temperature Profile Reconstruction

    Science.gov (United States)

    Clayton, D. J.; Tritz, K.; Finkenthal, M.; Kumar, D.; Stutman, D.

    2012-10-01

    New techniques utilizing computational tools such as neural networks and genetic algorithms are being developed to infer plasma electron temperature profiles on fast time scales (> 10 kHz) from multi-energy soft-x-ray (ME-SXR) diagnostics. Traditionally, a two-foil SXR technique, using the ratio of filtered continuum emission measured by two SXR detectors, has been employed on fusion devices as an indirect method of measuring electron temperature. However, these measurements can be susceptible to large errors due to uncertainties in time-evolving impurity density profiles, leading to unreliable temperature measurements. To correct this problem, measurements using ME-SXR diagnostics, which use three or more filtered SXR arrays to distinguish line and continuum emission from various impurities, in conjunction with constraints from spectroscopic diagnostics, can be used to account for unknown or time evolving impurity profiles [K. Tritz et al, Bull. Am. Phys. Soc. Vol. 56, No. 12 (2011), PP9.00067]. On NSTX, ME-SXR diagnostics can be used for fast (10-100 kHz) temperature profile measurements, using a Thomson scattering diagnostic (60 Hz) for periodic normalization. The use of more advanced algorithms, such as neural network processing, can decouple the reconstruction of the temperature profile from spectral modeling.

  19. QBO effects manifesting in ozone, temperature, and wind profiles

    Directory of Open Access Journals (Sweden)

    S. A. Sitnov

    2004-04-01

    Full Text Available On the basis of ozonesonde records up to 1998 the responses on the equatorial quasi-biennial oscillation (QBO, manifesting in ozone, temperature, and wind (QBO effects were isolated in the region from the ground to altitudes as high as 35km at 22 stations located in Europe (7, North America (7, Japan (4, Hawaii (1, Australia (2, and Antarctic (1.

    The vertical structures of the QBO effects of ozone are represented as an alternation of layers of well-developed quasi-biennial signals, whose phases gradually change with height and thin transitional layers of ill-developed signals, whose phases change abruptly with height. The amplitudes of the effects depend on height and reach the maxima of 3–6nbar in the lower stratosphere. At the majority of sites the effects are found to be approximately in phase between 20 and 23km.

    Two types of the vertical structures of the temperature QBO effects are found. At most of the sites located equatorward of about 50° the stratospheric temperature anomalies are characterized by downward propagation, whereas at sites situated poleward of about 50° they look as column-like structures. Near the tropopause the effects frequently reveal dipole-like structure, when the stratospheric and tropospheric anomalies are of opposite signs. The amplitudes of the effects are in the range of 0.5–1°C.

    The vertical structures of the QBO effects of horizontal wind components reveal a diversity of patterns. The amplitudes of the QBO effects of the meridional and zonal winds are comparable and lie in the range of 0.5–2m s–1. As a rule, the maxima of the effects are noticed slightly below the tropopause, as well as in the middle stratosphere.

    In general, a statistical assurance of the obtained QBO effects is rather poor. However, a considerable part of them reveal similarity

  20. Operational profiling of temperature using ground-based microwave radiometry at Payerne: prospects and challenges

    Directory of Open Access Journals (Sweden)

    U. Löhnert

    2012-05-01

    Full Text Available The motivation of this study is to verify theoretical expectations placed on ground-based microwave radiometer (MWR techniques and to confirm whether they are suitable for supporting key missions of national weather services, such as timely and accurate weather advisories and warnings. We evaluate reliability and accuracy of atmospheric temperature profiles retrieved continuously by the microwave profiler system HATPRO (Humidity And Temperature PROfiler operated at the aerological station of Payerne (MeteoSwiss in the time period August 2006–December 2009. Assessment is performed by comparing temperatures from the radiometer against temperature measurements from a radiosonde accounting for a total of 2107 quality-controlled all-season cases.

    In the evaluated time period, the MWR delivered reliable temperature profiles in 86% of all-weather conditions on a temporal resolution of 12–13 min. Random differences between MWR and radiosonde are down to 0.5 K in the lower boundary layer and increase to 1.7 K at 4 km height. The differences observed between MWR and radiosonde in the lower boundary layer are similar to the differences observed between the radiosonde and another in-situ sensor located on a close-by 30 m tower. Temperature retrievals from above 4 km contain less than 5% of the total information content of the measurements, which makes clear that this technique is mainly suited for continuous observations in the boundary layer. Systematic temperature differences are also observed throughout the retrieved profile and can account for up to ±0.5 K. These errors are due to offsets in the measurements of the microwave radiances that have been corrected for in data post-processing and lead to nearly bias-free overall temperature retrievals. Different reasons for the radiance offsets are discussed, but cannot be unambiguously determined retrospectively. Monitoring and, if necessary, corrections for radiance offsets as well as a real

  1. Stable, Extreme Temperature, High Radiation, Compact. Low Power Clock Oscillator for Space, Geothermal, Down-Hole & other High Reliability Applications, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Efficient and stable clock signal generation requirements at extreme temperatures (-180C to +450C)and radiation (>250 Krad TID) are not met with the current...

  2. Mathematical Simulation of Temperature Profiles within Microwave Heated Wood Made for Wood-Based Nano composites

    International Nuclear Information System (INIS)

    Li, X.; He, X.; Lv, J.; Wu, Y.; Luo, Y.; Chen, H.

    2013-01-01

    High intensive microwave pretreatment is a new method to modify wood for the fabrication of wood-based nano composites. Based on the physical law on heat transfer, a mathematical model to describe the temperature profiles within wood heated by high intensive microwave was established and simulated in this research. The results showed that the temperature profiles within wood were related to microwave heating methods; The temperature inside wood firstly increased and then gradually decreased along the direction of microwave transmission when the unilateral microwave heating was applied, and the temperature difference along the thickness direction of wood was very significant; The temperature with wood firstly increased and then gradually decreased from the wood surface to interior when the bilateral microwave heating was applied. Compared with the unilateral microwave heating, bilateral microwave heating is a better microwave heating method for the more uniform wood microwave pretreatment.

  3. Profile vertical of temperature in an atmosphere semi-gray with a layer of clouds

    International Nuclear Information System (INIS)

    Pelkowski, Joaquin; Anduckia Avila, Juan Carlos

    2000-01-01

    We extend earlier models of planetary layers in radioactive equilibrium by including scattering within a homogeneous cloud layer in a single direction. The atmospheric layers above and below the cloud layer are taken to be in radioactive equilibrium, whose temperature profiles may be calculated. Though the resulting profile, being discontinuous, is unrealistic, the model adds to the effects of the earlier models a cloud albedo, resulting from the scattering of short-wave radiation

  4. Multi-Energy Soft X-ray Measurements of the Electron Temperature Profile

    Science.gov (United States)

    Tritz, K.; Clayton, D. J.; Stutman, D.; Bell, R. E.; Diallo, A.; Leblanc, B. P.; Podesta, M.; Sabbagh, S.; NSTX Team

    2013-10-01

    A novel analysis method using a neural network algorithm has been used to reconstruct the electron temperature profile for high power NSTX discharges with fast time resolution (> 10 kHz) using multi-energy soft X-ray (ME-SXR) arrays both alone and in combination with low time-resolution space-resolved spectroscopy and a single chord of line-integrated density. This fast profile reconstruction uses the measured electron temperature profile from the 60 Hz multipoint Thomson scattering (MPTS) diagnostic to train the neural network with the high time resolution ME-SXR data. Comparisons using cross-validation between the neural network reconstruction and the measured Te profiles from MPTS show agreement within 5% over the profile radius. The accuracy of the neural network reconstruction demonstrates the ability to use ME-SXR diagnostics for high time resolution electron temperature measurements, and will be available on both EAST and NSTX-U for studies of electron heat transport as well as other general studies including impurity/particle transport, ELM profile dynamics, and MHD. Work supported by DoE grant no. DE-FG02-09ER55012.

  5. Surface reflectance drives nest box temperature profiles and thermal suitability for target wildlife.

    Directory of Open Access Journals (Sweden)

    Stephen R Griffiths

    Full Text Available Thermal properties of tree hollows play a major role in survival and reproduction of hollow-dependent fauna. Artificial hollows (nest boxes are increasingly being used to supplement the loss of natural hollows; however, the factors that drive nest box thermal profiles have received surprisingly little attention. We investigated how differences in surface reflectance influenced temperature profiles of nest boxes painted three different colors (dark-green, light-green, and white: total solar reflectance 5.9%, 64.4%, and 90.3% respectively using boxes designed for three groups of mammals: insectivorous bats, marsupial gliders and brushtail possums. Across the three different box designs, dark-green (low reflectance boxes experienced the highest average and maximum daytime temperatures, had the greatest magnitude of variation in daytime temperatures within the box, and were consistently substantially warmer than light-green boxes (medium reflectance, white boxes (high reflectance, and ambient air temperatures. Results from biophysical model simulations demonstrated that variation in diurnal temperature profiles generated by painting boxes either high or low reflectance colors could have significant ecophysiological consequences for animals occupying boxes, with animals in dark-green boxes at high risk of acute heat-stress and dehydration during extreme heat events. Conversely in cold weather, our modelling indicated that there are higher cumulative energy costs for mammals, particularly smaller animals, occupying light-green boxes. Given their widespread use as a conservation tool, we suggest that before boxes are installed, consideration should be given to the effect of color on nest box temperature profiles, and the resultant thermal suitability of boxes for wildlife, particularly during extremes in weather. Managers of nest box programs should consider using several different colors and installing boxes across a range of both orientations and

  6. Surface reflectance drives nest box temperature profiles and thermal suitability for target wildlife.

    Science.gov (United States)

    Griffiths, Stephen R; Rowland, Jessica A; Briscoe, Natalie J; Lentini, Pia E; Handasyde, Kathrine A; Lumsden, Linda F; Robert, Kylie A

    2017-01-01

    Thermal properties of tree hollows play a major role in survival and reproduction of hollow-dependent fauna. Artificial hollows (nest boxes) are increasingly being used to supplement the loss of natural hollows; however, the factors that drive nest box thermal profiles have received surprisingly little attention. We investigated how differences in surface reflectance influenced temperature profiles of nest boxes painted three different colors (dark-green, light-green, and white: total solar reflectance 5.9%, 64.4%, and 90.3% respectively) using boxes designed for three groups of mammals: insectivorous bats, marsupial gliders and brushtail possums. Across the three different box designs, dark-green (low reflectance) boxes experienced the highest average and maximum daytime temperatures, had the greatest magnitude of variation in daytime temperatures within the box, and were consistently substantially warmer than light-green boxes (medium reflectance), white boxes (high reflectance), and ambient air temperatures. Results from biophysical model simulations demonstrated that variation in diurnal temperature profiles generated by painting boxes either high or low reflectance colors could have significant ecophysiological consequences for animals occupying boxes, with animals in dark-green boxes at high risk of acute heat-stress and dehydration during extreme heat events. Conversely in cold weather, our modelling indicated that there are higher cumulative energy costs for mammals, particularly smaller animals, occupying light-green boxes. Given their widespread use as a conservation tool, we suggest that before boxes are installed, consideration should be given to the effect of color on nest box temperature profiles, and the resultant thermal suitability of boxes for wildlife, particularly during extremes in weather. Managers of nest box programs should consider using several different colors and installing boxes across a range of both orientations and shade profiles (i

  7. Fitting of the Thomson scattering density and temperature profiles on the COMPASS tokamak

    International Nuclear Information System (INIS)

    Stefanikova, E.; Peterka, M.; Bohm, P.; Bilkova, P.; Aftanas, M.; Urban, J.; Hron, M.; Panek, R.; Sos, M.

    2016-01-01

    A new technique for fitting the full radial profiles of electron density and temperature obtained by the Thomson scattering diagnostic in H-mode discharges on the COMPASS tokamak is described. The technique combines the conventionally used modified hyperbolic tangent function for the edge transport barrier (pedestal) fitting and a modification of a Gaussian function for fitting the core plasma. Low number of parameters of this combined function and their straightforward interpretability and controllability provide a robust method for obtaining physically reasonable profile fits. Deconvolution with the diagnostic instrument function is applied on the profile fit, taking into account the dependence on the actual magnetic configuration.

  8. A new temperature profiling probe for investigating groundwater-surface water interaction

    Science.gov (United States)

    Naranjo, Ramon C.; Robert Turcotte,

    2015-01-01

    Measuring vertically nested temperatures at the streambed interface poses practical challenges that are addressed here with a new discrete subsurface temperature profiling probe. We describe a new temperature probe and its application for heat as a tracer investigations to demonstrate the probe's utility. Accuracy and response time of temperature measurements made at 6 discrete depths in the probe were analyzed in the laboratory using temperature bath experiments. We find the temperature probe to be an accurate and robust instrument that allows for easily installation and long-term monitoring in highly variable environments. Because the probe is inexpensive and versatile, it is useful for many environmental applications that require temperature data collection for periods of several months in environments that are difficult to access or require minimal disturbance.

  9. Response of temperature and density profiles to heat deposition profile and its impact on global scaling in LHD

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, H.; Murakami, S.; Yamazaki, K. [and others

    2002-10-01

    Energy confinement and heat transport of net current-free NBI-heated plasmas in the Large Helical Device (LHD) are discussed with an emphasis on density dependence. Although the apparent density dependence of the energy confinement time has been demonstrated in a wide parameter range in LHD, the loss of this dependence has been observed in the high density regime under the specific condition. Broad heat deposition due to off-axis alignment and shallow penetration of neutral beams degrades the global energy confinement while the local heat transport maintains a clear temperature dependence lying between Bohm and gyro-Bohm characteristics. The central heat deposition inclines towards an intrinsic density dependence like {tau}{sub E} {proportional_to} (n-bar{sub e}/P){sup 0.6} from the saturated state. The broadening of the temperature profile due to the broad heat deposition profile contrasts with the invariant property which has observed widely as profile consistency and stiffness in tokamak experiments. (author)

  10. Factors influencing intra-articular fluid temperature profiles with radiofrequency ablation.

    Science.gov (United States)

    Zoric, Bojan B; Horn, Nils; Braun, Sepp; Millett, Peter J

    2009-10-01

    Radiofrequency ablation devices are being used increasingly in arthroscopic surgery. However, there are concerns that excessive temperatures may damage the articular cartilage. The purpose of this study was to investigate the temperature profiles that occur within the glenohumeral space with the use of one commercially available radiofrequency ablation probe. Ten fresh-frozen human cadaver shoulder specimens were used. Intra-articular temperatures were measured at different time intervals over a two-minute period at a distance of 1, 3, 5, and 10 mm away from the probe. The radiofrequency probe was activated throughout the range of machine power settings, and irrigation fluid flow was varied (no flow, a flow at 60 mm Hg without suction, and a flow at 60 mm Hg with suction). Temperatures deleterious to articular cartilage chondrocytes (i.e., those in excess of 50 degrees C) were seen with an increased duration of application, a decreased distance between the thermometer and the probe, and a decreased irrigation fluid flow rate. The highest recorded irrigation fluid temperature reached >80 degrees C after two minutes in a no-flow setting. The flow rate was found to be the most significant predictor of intra-articular temperature profiles. The various machine power settings had no apparent influence on temperature, meaning that higher probe settings are not necessarily associated with higher temperature profiles. These results demonstrate the importance of the management of the irrigation fluid flow rate across the joint during arthroscopic procedures that involve radiofrequency ablation. Even short intervals of limited flow could lead to supraphysiological temperature profiles and potentially to cartilage damage.

  11. Synoptic monthly gridded Global Temperature and Salinity Profile Programme (GTSPP) water temperature and salinity from January 1990 to December 2009 (NCEI Accession 0138647)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The synoptic gridded Global Temperature and Salinity Profile Programme (SG-GTSPP) provides world ocean 3D gridded temperature and salinity data in monthly increment...

  12. Fe-O stable isotope pairs elucidate a high-temperature origin of Chilean iron oxide-apatite deposits

    Science.gov (United States)

    Bilenker, Laura D.; Simon, Adam C.; Reich, Martin; Lundstrom, Craig C.; Gajos, Norbert; Bindeman, Ilya; Barra, Fernando; Munizaga, Rodrigo

    2016-03-01

    Iron oxide-apatite (IOA) ore deposits occur globally and can host millions to billions of tons of Fe in addition to economic reserves of other metals such as rare earth elements, which are critical for the expected growth of technology and renewable energy resources. In this study, we pair the stable Fe and O isotope compositions of magnetite samples from several IOA deposits to constrain the source reservoir of these elements in IOAs. Since magnetite constitutes up to 90 modal% of many IOAs, identifying the source of Fe and O within the magnetite may elucidate high-temperature and/or lower-temperature processes responsible for their formation. Here, we focus on the world-class Los Colorados IOA in the Chilean iron belt (CIB), and present data for magnetite from other Fe oxide deposits in the CIB (El Laco, Mariela). We also report Fe and O isotopic values for other IOA deposits, including Mineville, New York (USA) and the type locale, Kiruna (Sweden). The ranges of Fe isotopic composition (δ56Fe, 56Fe/54Fe relative to IRMM-14) of magnetite from the Chilean deposits are: Los Colorados, δ56Fe (±2σ) = 0.08 ± 0.03‰ to 0.24 ± 0.08‰; El Laco, δ56Fe = 0.20 ± 0.03‰ to 0.53 ± 0.03‰; Mariela, δ56Fe = 0.13 ± 0.03‰. The O isotopic composition (δ18O, 18O/16O relative to VSMOW) of the same Chilean magnetite samples are: Los Colorados, δ18O (±2σ) = 1.92 ± 0.08‰ to 3.17 ± 0.03‰; El Laco, δ18O = 4.00 ± 0.10‰ to 4.34 ± 0.10‰; Mariela, δ18O = (1.48 ± 0.04‰). The δ18O and δ56Fe values for Kiruna magnetite yield an average of 1.76 ± 0.25‰ and 0.16 ± 0.07‰, respectively. The Fe and O isotope data from the Chilean IOAs fit unequivocally within the range of magnetite formed by high-temperature magmatic or magmatic-hydrothermal processes (i.e., δ56Fe 0.06-0.49‰ and δ18O = 1.0-4.5‰), consistent with a high-temperature origin for Chilean IOA deposits. Additionally, minimum formation temperatures calculated by using the measured Δ18O

  13. An Experimental Investigation Into the Temperature Profile of a Compliant Foil Air Bearing

    Science.gov (United States)

    Radil, Kevin; Zeszotek, Michelle

    2004-01-01

    A series of tests was performed to determine the internal temperature profile in a compliant bump-type foil journal air bearing operating at room temperature under various speeds and load conditions. The temperature profile was collected by instrumenting a foil bearing with nine, type K thermocouples arranged in the center and along the bearing s edges in order to measure local temperatures and estimate thermal gradients in the axial and circumferential directions. To facilitate the measurement of maximum temperatures from viscous shearing in the air film, the thermocouples were tack welded to the backside of the bumps that were in direct contact with the top foil. The mating journal was coated with a high temperature solid lubricant that, together with the bearing, underwent high temperature start-stop cycles to produce a smooth, steady-state run-in surface. Tests were conducted at speeds from 20 to 50 krpm and loads ranging from 9 to 222 N. The results indicate that, over the conditions tested, both journal rotational speed and radial load are responsible for heat generation with speed playing a more significant role in the magnitude of the temperatures. The temperature distribution was nearly symmetric about the bearing center at 20 and 30 krpm but became slightly skewed toward one side at 40 and 50 krpm. Surprisingly, the maximum temperatures did not occur at the bearing edge where the minimum film thickness is expected but rather in the middle of the bearing where analytical investigations have predicted the air film to be much thicker. Thermal gradients were common during testing and were strongest in the axial direction from the middle of the bearing to its edges, reaching 3.78 8C/mm. The temperature profile indicated the circumferential thermal gradients were negligible.

  14. Electrodeposition of selenium, indium and copper in an air- and water-stable ionic liquid at variable temperatures

    International Nuclear Information System (INIS)

    Zein El Abedin, S.; Saad, A.Y.; Farag, H.K.; Borisenko, N.; Liu, Q.X.; Endres, F.

    2007-01-01

    The electrochemical behaviour of Au(1 1 1) and highly oriented pyrolytic graphite (HOPG) substrates in the air- and water-stable ionic liquid 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)amide ([BMP]Tf 2 N) was investigated using in situ scanning tunneling microscopy (STM). Furthermore, the electrodeposition of Se, In and Cu in the same ionic liquid was investigated. The high thermal stability as well as the large electrochemical window of this ionic liquid compared with aqueous electrolytes allow the direct electrodeposition of grey selenium, indium and copper at variable temperatures, as the first step in making CIS solar cells electrochemically, in a one pot reaction. The results show that grey selenium can be obtained at temperatures ≥100 o C. XRD patterns of the electrodeposit obtained at 100 o C show the characteristic peaks of crystalline grey selenium. Nanocrystalline indium with grain sizes between 100 and 200 nm was formed in the employed ionic liquid, containing 0.1 M InCl 3 , at room temperature. It was also found that copper(I) species can be introduced into the ionic liquid [BMP]Tf 2 N by anodic dissolution of a copper electrode and nanocrystalline copper with an average crystallite size of about 50 nm was obtained without additives in the resulting electrolyte

  15. Stationary temperature profiles in a liquid nanochannel: comparisons between molecular-dynamics simulation and classical hydrostatics.

    Science.gov (United States)

    Okumura, Hisashi; Heyes, David M

    2006-12-01

    We compare the results of three-dimensional molecular-dynamics (MD) simulations of a Lennard-Jones (LJ) liquid with a hydrostatic (HS) solution of a high temperature liquid channel which is surrounded by a fluid at lower temperature. The maximum temperature gradient, dT/dx , between the two temperature regions ranged from infinity (step function) to dT/dx=0.1 (in the usual LJ units). Because the systems were in stationary-nonequilibrium states with no fluid flow, both MD simulation and the HS solution gave flat profiles for the normal pressure in all temperature-gradient cases. However, the other quantities showed differences between the two methods. The MD-derived density was found to oscillate over the length of ca. 8 LJ particle diameters from the boundary plane in the system with the infinite temperature gradient, while the HS-derived density showed simply a stepwise profile. The MD simulation also showed another anomaly near the boundary in potential energy. We have found systems in which the HS treatment works well and those where the HS approach breaks down, and therefore established the minimum length scale for the HS treatment to be valid. We also compare the kinetic temperature and the configurational temperature in these systems, and show that these can differ in the transition zone between the two temperatures.

  16. Dynamic temperature and humidity environmental profiles: impact for future emergency and disaster preparedness and response.

    Science.gov (United States)

    Ferguson, William J; Louie, Richard F; Tang, Chloe S; Paw U, Kyaw Tha; Kost, Gerald J

    2014-02-01

    During disasters and complex emergencies, environmental conditions can adversely affect the performance of point-of-care (POC) testing. Knowledge of these conditions can help device developers and operators understand the significance of temperature and humidity limits necessary for use of POC devices. First responders will benefit from improved performance for on-site decision making. To create dynamic temperature and humidity profiles that can be used to assess the environmental robustness of POC devices, reagents, and other resources (eg, drugs), and thereby, to improve preparedness. Surface temperature and humidity data from the National Climatic Data Center (Asheville, North Carolina USA) was obtained, median hourly temperature and humidity were calculated, and then mathematically stretched profiles were created to include extreme highs and lows. Profiles were created for: (1) Banda Aceh, Indonesia at the time of the 2004 Tsunami; (2) New Orleans, Louisiana USA just before and after Hurricane Katrina made landfall in 2005; (3) Springfield, Massachusetts USA for an ambulance call during the month of January 2009; (4) Port-au-Prince, Haiti following the 2010 earthquake; (5) Sendai, Japan for the March 2011 earthquake and tsunami with comparison to the colder month of January 2011; (6) New York, New York USA after Hurricane Sandy made landfall in 2012; and (7) a 24-hour rescue from Hawaii USA to the Marshall Islands. Profiles were validated by randomly selecting 10 days and determining if (1) temperature and humidity points fell inside and (2) daily variations were encompassed. Mean kinetic temperatures (MKT) were also assessed for each profile. Profiles accurately modeled conditions during emergency and disaster events and enclosed 100% of maximum and minimum temperature and humidity points. Daily variations also were represented well with 88.6% (62/70) of temperature readings and 71.1% (54/70) of relative humidity readings falling within diurnal patterns. Days

  17. Retrieval of upper atmosphere pressure-temperature profiles from high resolution solar occultation spectra

    Science.gov (United States)

    Rinsland, C. P.; Russell, J. M., III; Park, J. H.; Namkung, J.

    1987-01-01

    Pressure-temperature profiles over the 18 to 75 km altitude range were retrieved from 0.01 cm(-1) resolution infrared solar absorption spectra recorded with the Atmospheric Trace Molecule Spectroscopy (ATMOS) Fourier transform spectrometer operating in the solar occultation mode during the Spacelab 3 shuttle mission (April 30 to May 1, 1985). The analysis method is described and preliminary results deduced for five occultation events are compared to correlative pressure-temperature measurments.

  18. Protein remains stable at unusually high temperatures when solvated in aqueous mixtures of amino acid based ionic liquids

    DEFF Research Database (Denmark)

    Chevrot, Guillaume; Fileti, Eudes Eterno; Chaban, Vitaly V.

    2016-01-01

    Using molecular dynamics simulations, we investigated the thermal stability and real-time denaturation of a model mini-protein in four solvents: (1) water, (2) 1-ethyl-3-methylimidazolium alaninate [EMIM][ALA] (5 mol% in water), (3) methioninate [EMIM][MET] (5 mol% in water), and (4) tryptophanate...... [EMIM][TRP] (5 mol% in water). Upon analyzing the radius of gyration, the solvent-accessible surface area, root-mean-squared deviations, and inter- and intramolecular hydrogen bonds, we found that the mini-protein remains stable at 30–40 K higher temperatures in aqueous amino acid based ionic liquids...... (AAILs) than in water. This thermal stability was correlated with the thermodynamics and shear viscosity of the AAIL-containing mixtures. These results suggest that AAILs are generally favorable for protein conservation. [Figure not available: see fulltext.]...

  19. High Temperature Stable Separator for Lithium Batteries Based on SiO2 and Hydroxypropyl Guar Gum

    Directory of Open Access Journals (Sweden)

    Diogo Vieira Carvalho

    2015-10-01

    Full Text Available A novel membrane based on silicon dioxide (SiO2 and hydroxypropyl guar gum (HPG as binder is presented and tested as a separator for lithium-ion batteries. The separator is made with renewable and low cost materials and an environmentally friendly manufacturing processing using only water as solvent. The separator offers superior wettability and high electrolyte uptake due to the optimized porosity and the good affinity of SiO2 and guar gum microstructure towards organic liquid electrolytes. Additionally, the separator shows high thermal stability and no dimensional-shrinkage at high temperatures due to the use of the ceramic filler and the thermally stable natural polymer. The electrochemical tests show the good electrochemical stability of the separator in a wide range of potential, as well as its outstanding cycle performance.

  20. Measurement of the electron temperature profiles in the F-1 cold gas blanket experiment by hydrogen line-spectroscopy

    International Nuclear Information System (INIS)

    Kuthy, A.

    1981-01-01

    Radial profiles of the electron temperature in the F-1 device were determined by measurements of the hydrogen Balmer β-line intensity. The F-1 device produces plasmas in the parameter range of cold gas blankets. The measured temperatures were in agreement with earlier theoretical estimates. The temperature amplitudes and profile shapes were strongly dependent on the power input. The neutral penetration length was dominated by temperature profile effects. The temperature of the ionization zone was essentially constant at 2.5 eV independent of the peak temperature. (orig.)

  1. Endovenous simulated laser experiments at 940 nm and 1470 nm suggest wavelength-independent temperature profiles.

    Science.gov (United States)

    van den Bos, R R; van Ruijven, P W M; van der Geld, C W M; van Gemert, M J C; Neumann, H A M; Nijsten, T

    2012-07-01

    EVLA has proven to be very successful, but the optimum methods for energy delivery have still not been clarified. A better understanding of the mechanism of action may contribute to achieving a consensus on the best laser method and the most effective use of laser parameters, resulting in optimal clinical outcomes, maintaining high success rates with minimal adverse events. The aim of this study is to assess the impact of wavelength, pullback speed and power level on the endovenous temperature profile in an experimental setting. In an experimental setting, temperature measurements were performed using thermocouples. The experimental set-up consisted of a transparent box in which a glass tube was fixed. Different laser parameters (wavelength and power) and 2 different pullback speeds (2 and 5 mm/s) were used. Thermocouples were placed at different distances from the fiber tip. Validity of the experimental setting was assessed by performing the same temperature measurements using a stripped varicose vein. The maximal temperature rise and the time span that the temperature was above collagen denaturation temperature were measured. The experiments showed that decreasing the pullback speed (2 mm/s) and increasing the power (up to 14 W) both cause higher maximal temperature and a longer time above the temperature for collagen denaturation. The use of different laser wavelengths (940 or 1470 nm) did not influence the temperature profile. The results of our experiments show that wavelength on its own has not been demonstrated to be an important parameter to influence the temperature profile. Copyright © 2012 European Society for Vascular Surgery. Published by Elsevier Ltd. All rights reserved.

  2. Direct Observation of Room-Temperature Stable Magnetism in LaAlO3/SrTiO3 Heterostructures.

    Science.gov (United States)

    Yang, Ming; Ariando; Zhou, Jun; Asmara, Teguh Citra; Krüger, Peter; Yu, Xiao Jiang; Wang, Xiao; Sanchez-Hanke, Cecilia; Feng, Yuan Ping; Venkatesan, T; Rusydi, Andrivo

    2018-03-21

    Along with an unexpected conducting interface between nonmagnetic insulating perovskites LaAlO 3 and SrTiO 3 (LaAlO 3 /SrTiO 3 ), striking interfacial magnetisms have been observed in LaAlO 3 /SrTiO 3 heterostructures. Interestingly, the strength of the interfacial magnetic moment is found to be dependent on oxygen partial pressures during the growth process. This raises an important, fundamental question on the origin of these remarkable interfacial magnetic orderings. Here, we report a direct evidence of room-temperature stable magnetism in a LaAlO 3 /SrTiO 3 heterostructure prepared at high oxygen partial pressure by using element-specific soft X-ray magnetic circular dichroism at both Ti L 3,2 and O K edges. By combining X-ray absorption spectroscopy at both Ti L 3,2 and O K edges and first-principles calculations, we qualitatively ascribe that this strong magnetic ordering with dominant interfacial Ti 3+ character is due to the coexistence of LaAlO 3 surface oxygen vacancies and interfacial (Ti Al -Al Ti ) antisite defects. On the basis of this new understanding, we revisit the origin of the weak magnetism in LaAlO 3 /SrTiO 3 heterostructures prepared at low oxygen partial pressures. Our calculations show that LaAlO 3 surface oxygen vacancies are responsible for the weak magnetism at the interface. Our result provides direct evidence on the presence of room-temperature stable magnetism and a novel perspective to understand magnetic and electronic reconstructions at such strategic oxide interfaces.

  3. Control of nanoparticle agglomeration through variation of the time-temperature profile in chemical vapor synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Djenadic, Ruzica; Winterer, Markus, E-mail: markus.winterer@uni-due.de [Universität Duisburg-Essen, Nanoparticle Process Technology, Faculty of Engineering and CENIDE (Germany)

    2017-02-15

    The influence of the time-temperature history on the characteristics of nanoparticles such as size, degree of agglomeration, or crystallinity is investigated for chemical vapor synthesis (CVS). A simple reaction-coagulation-sintering model is used to describe the CVS process, and the results of the model are compared to experimental data. Nanocrystalline titania is used as model material. Titania nanoparticles are generated from titanium-tetraisopropoxide (TTIP) in a hot-wall reactor. Pure anatase particles and mixtures of anatase, rutile (up to 11 vol.%), and brookite (up to 29 vol.%) with primary particle sizes from 1.7 nm to 10.5 nm and agglomerate particle sizes from 24.3 nm to 55.6 nm are formed depending on the particle time-temperature history. An inductively heated furnace with variable inductor geometry is used as a novel system to control the time-temperature profile in the reactor externally covering a large wall temperature range from 873 K to 2023 K. An appropriate choice of inductor geometry, i.e. time-temperature profile, can significantly reduce the degree of agglomeration. Other particle characteristics such as crystallinity are also substantially influenced by the time-temperature profile.

  4. Rayleigh-Brillouin scattering profiles of air at different temperatures and pressures

    NARCIS (Netherlands)

    Gu, Z.; Witschas, B.; van der Water, W.; Ubachs, W.M.G.

    2013-01-01

    Rayleigh-Brillouin (RB) scattering profiles for air have been recorded for the temperature range from 255 to 340 K and the pressure range from 640 to 3300 mbar, covering the conditions relevant for the Earth's atmosphere and for planned atmospheric light detection and ranging (LIDAR) missions. The

  5. Gene expression profiling of a temperature-sensitive strain of Neospora caninum

    Science.gov (United States)

    To understand the genetic basis of virulence, gene expression profiles of a temperature-sensitive clone (NCts-8, relatively avirulent) and its wild type (NC-1) of Neospora caninum were characterized and compared using a high-density microarray with approximately 63,000 distinct oligonucleotides. Thi...

  6. Room temperature Compton profiles of conduction electrons in α-Ga ...

    Indian Academy of Sciences (India)

    B P PANDA and N C MOHAPATRA*. Department of Physics, Chikiti Mahavidyalaya, Chikiti 761 010, India. £Department of Physics, Berhampur University, Berhampur 760 007, India. Email: ncmphy123@hotmail.com. MS received 18 January 2003; accepted 21 June 2003. Abstract. Room temperature Compton profiles of ...

  7. Stable Isotope Ratio and Elemental Profile Combined with Support Vector Machine for Provenance Discrimination of Oolong Tea (Wuyi-Rock Tea

    Directory of Open Access Journals (Sweden)

    Yun-xiao Lou

    2017-01-01

    Full Text Available This paper focused on an effective method to discriminate the geographical origin of Wuyi-Rock tea by the stable isotope ratio (SIR and metallic element profiling (MEP combined with support vector machine (SVM analysis. Wuyi-Rock tea (n=99 collected from nine producing areas and non-Wuyi-Rock tea (n=33 from eleven nonproducing areas were analysed for SIR and MEP by established methods. The SVM model based on coupled data produced the best prediction accuracy (0.9773. This prediction shows that instrumental methods combined with a classification model can provide an effective and stable tool for provenance discrimination. Moreover, every feature variable in stable isotope and metallic element data was ranked by its contribution to the model. The results show that δ2H, δ18O, Cs, Cu, Ca, and Rb contents are significant indications for provenance discrimination and not all of the metallic elements improve the prediction accuracy of the SVM model.

  8. Automated and temperature-controlled micro-PIV measurements enabling long-term-stable microchannel acoustophoresis characterization.

    Science.gov (United States)

    Augustsson, Per; Barnkob, Rune; Wereley, Steven T; Bruus, Henrik; Laurell, Thomas

    2011-12-21

    We present a platform for micro particle image velocimetry (μPIV), capable of carrying out full-channel, temperature-controlled, long-term-stable, and automated μPIV-measurement of microchannel acoustophoresis with uncertainties below 5% and a spatial resolution in the order of 20 μm. A method to determine optimal μPIV-settings for obtaining high-quality results of the spatially inhomogeneous acoustophoretic velocity fields of large dynamical range is presented. In particular we study the dependence of the results on the μPIV interrogation window size and the number of repeated experiments. The μPIV-method was further verified by comparing it with our previously published particle tracking method. Using the μPIV platform we present a series of high-resolution measurements of the acoustophoretic velocity field as a function of the driving frequency, the driving voltage, and the resonator temperature. Finally, we establish a direct and consistent connection between the obtained acoustophoretic velocity fields, and continuous flow mode acoustophoresis, commonly used in applications.

  9. MODIS/Terra Temperature and Water Vapor Profiles 5-Min L2 Swath 5km V006

    Data.gov (United States)

    National Aeronautics and Space Administration — Level 2 Daily global Total Ozone Burden, Atmospheric Stability, Temperature and Moisture Profiles at 20 vertical levels for temperature and 15 levels for moisture,...

  10. MODIS/Aqua Temperature and Water Vapor Profiles 5-Min L2 Swath 5km V005 NRT

    Data.gov (United States)

    National Aeronautics and Space Administration — Level 2 Daily global Total Ozone Burden, Atmospheric Stability, Temperature and Moisture Profiles at 20 vertical levels for temperature and 15 levels for moisture,...

  11. MODIS/Terra Near Real Time (NRT) Temperature and Water Vapor Profiles 5-Min L2 Swath 5km

    Data.gov (United States)

    National Aeronautics and Space Administration — The level-2 MODIS Temperature and Water Vapor Profile Product MOD07_L2 consists of 30 gridded parameters related to atmospheric stability, atmospheric temperature...

  12. Temperature-dependent electronic decay profiles in CZT: probe of bulk and surface properties

    Science.gov (United States)

    Kessick, Royal; Maupin, Hugh; Tepper, Gary C.; Szeles, Csaba

    2003-01-01

    The electronic performance of CZT-based gamma radiation spectrometers is governed by a synergism of bulk and surface properties. Compensation is used to increase the bulk resistivity of Cd1-xZnxTe (x~0.1), but the same electronic states that are introduced to increase the material resistivity can also trap charge and reduce the carrier lifetime. Electrical and mechanical surface defects introduced during or subsequent to crystal harvesting are also known to interfere with device performance. Using a contactless, pulsed laser microwave cavity perturbation technique, electronic decay profiles were studied in high pressure Bridgman CZT as a function of temperature. The electronic decay profile was found to depend very strongly on temperature and was modeled using a function consisting of two exponential terms with temperature-dependent amplitudes and time constants. The model was used to relate the observed temperature dependent decay kinetics in CZT to specific trap energies. It was found that, at low temperatures, the electronic decay process is dominated by a deep trap with an energy of approximately 0.69 +/- 0.1 eV from the band edge. As the temperature is increased, the charge trapping becomes dominated by a second trap with an energy of approximately 0.60 +/- 0.1 eV from the band edge. Surface damage introduces additional charge traps that significantly alter the decay kinetics particularly at low temperatures.

  13. Confinement properties of JET plasmas with different temperature and density profiles

    International Nuclear Information System (INIS)

    Watkins, M.L.; Balet, B.; Bhatnagar, V.P.

    1989-01-01

    The confinement properties of plasmas with substantially different temperature and density profiles have been analysed. The effects of fast particles and energy pedestals on the overall confinement of plasma energy in limiter (L-mode) and X-point (L- and H-modes) discharges heated by NBI or ICRF or both are determined. The importance of the bootstrap current when such energy pedestals are formed is noted. Using sets of consistent experimental data, including ion temperature profile measurements, the local transport properties are compared in the L- and H-phases of a single null X-point medium density NBI heated discharge, the ''enhanced'' confinement phase of a limiter high density pellet-fuelled and ICRF heated discharge, the hot-ion phase of a double null X-point low density NBI heated discharge and the hot-ion and H-phases of a double null X-point low density high temperature NBI heated discharge. (author)

  14. Improving 7-Day Forecast Skill by Assimilation of Retrieved AIRS Temperature Profiles

    Science.gov (United States)

    Susskind, Joel; Rosenberg, Bob

    2016-01-01

    We conducted a new set of Data Assimilation Experiments covering the period January 1 to February 29, 2016 using the GEOS-5 DAS. Our experiments assimilate all data used operationally by GMAO (Control) with some modifications. Significant improvement in Global and Southern Hemisphere Extra-tropical 7-day forecast skill was obtained when: We assimilated AIRS Quality Controlled temperature profiles in place of observed AIRS radiances, and also did not assimilate CrISATMS radiances, nor did we assimilate radiosonde temperature profiles or aircraft temperatures. This new methodology did not improve or degrade 7-day Northern Hemispheric Extra-tropical forecast skill. We are conducting experiments aimed at further improving of Northern Hemisphere Extra-tropical forecast skill.

  15. Observation of Flat Electron Temperature Profiles in the Lithium Tokamak Experiment

    International Nuclear Information System (INIS)

    Boyle, D. P.; Majeski, R.; Schmitt, J. C.; Auburn University, AL; Hansen, C.

    2017-01-01

    It has been predicted for over a decade that low-recycling plasma-facing components in fusion devices would allow high edge temperatures and flat or nearly flat temperature profiles. In recent experiments with lithium wall coatings in the Lithium Tokamak Experiment (LTX), a hot edge (> 200 eV) and flat electron temperature profiles have been measured following the termination of external fueling. In this work, reduced recycling was demonstrated by retention of ~ 60% of the injected hydrogen in the walls following the discharge. Electron energy confinement followed typical Ohmic confinement scaling during fueling, but did not decrease with density after fueling terminated, ultimately exceeding the scaling by ~ 200% . Lastly, achievement of the low-recycling, hot edge regime has been an important goal of LTX and lithium plasma-facing component research in general, as it has potentially significant implications for the operation, design, and cost of fusion devices.

  16. Intercomparison of stratospheric temperature profiles from a ground-based microwave radiometer with other techniques

    Science.gov (United States)

    Navas-Guzmán, Francisco; Kämpfer, Niklaus; Schranz, Franziska; Steinbrecht, Wolfgang; Haefele, Alexander

    2017-11-01

    In this work the stratospheric performance of a relatively new microwave temperature radiometer (TEMPERA) has been evaluated. With this goal in mind, almost 3 years of temperature measurements (January 2014-September 2016) from the TEMPERA radiometer were intercompared with simultaneous measurements from other techniques: radiosondes, MLS satellite and Rayleigh lidar. This intercomparison campaign was carried out at the aerological station of MeteoSwiss at Payerne (Switzerland). In addition, the temperature profiles from TEMPERA were used to validate the temperature outputs from the SD-WACCM model. The results showed in general a very good agreement between TEMPERA and the different instruments and the model, with a high correlation (higher than 0.9) in the temperature evolution at different altitudes between TEMPERA and the different data sets. An annual pattern was observed in the stratospheric temperature with generally higher temperatures in summer than in winter and with a higher variability during winter. A clear change in the tendency of the temperature deviations was detected in summer 2015, which was due to the repair of an attenuator in the TEMPERA spectrometer. The mean and the standard deviations of the temperature differences between TEMPERA and the different measurements were calculated for two periods (before and after the repair) in order to quantify the accuracy and precision of this radiometer over the campaign period. The results showed absolute biases and standard deviations lower than 2 K for most of the altitudes. In addition, comparisons proved the good performance of TEMPERA in measuring the temperature in the stratosphere.

  17. Well-posed two-temperature constitutive equations for stable dense fluid shock waves using molecular dynamics and generalizations of Navier-Stokes-Fourier continuum mechanics.

    Science.gov (United States)

    Hoover, Wm G; Hoover, Carol G

    2010-04-01

    Guided by molecular dynamics simulations, we generalize the Navier-Stokes-Fourier constitutive equations and the continuum motion equations to include both transverse and longitudinal temperatures. To do so we partition the contributions of the heat transfer, the work done, and the heat flux vector between the longitudinal and transverse temperatures. With shockwave boundary conditions time-dependent solutions of these equations converge to give stationary shockwave profiles. The profiles include anisotropic temperature and can be fitted to molecular dynamics results, demonstrating the utility and simplicity of a two-temperature description of far-from-equilibrium states.

  18. Effects of temperature and glycerol and methanol-feeding profiles on the production of recombinant galactose oxidase in Pichia pastoris.

    Science.gov (United States)

    Anasontzis, George E; Salazar Penã, Margarita; Spadiut, Oliver; Brumer, Harry; Olsson, Lisbeth

    2014-01-01

    Optimization of protein production from methanol-induced Pichia pastoris cultures is necessary to ensure high productivity rates and high yields of recombinant proteins. We investigated the effects of temperature and different linear or exponential methanol-feeding rates on the production of recombinant Fusarium graminearum galactose oxidase (EC 1.1.3.9) in a P. pastoris Mut(+) strain, under regulation of the AOX1 promoter. We found that low exponential methanol feeding led to 1.5-fold higher volumetric productivity compared to high exponential feeding rates. The duration of glycerol feeding did not affect the subsequent product yield, but longer glycerol feeding led to higher initial biomass concentration, which would reduce the oxygen demand and generate less heat during induction. A linear and a low exponential feeding profile led to productivities in the same range, but the latter was characterized by intense fluctuations in the titers of galactose oxidase and total protein. An exponential feeding profile that has been adapted to the apparent biomass concentration results in more stable cultures, but the concentration of recombinant protein is in the same range as when constant methanol feeding is employed. © 2014 The Authors Biotechnology Progress published by Wiley Periodicals, Inc. on behalf of American Institute of Chemical Engineers.

  19. Effects of temperature and glycerol and methanol-feeding profiles on the production of recombinant galactose oxidase in Pichia pastoris

    Science.gov (United States)

    Anasontzis, George E; Salazar Penã, Margarita; Spadiut, Oliver; Brumer, Harry; Olsson, Lisbeth

    2014-01-01

    Optimization of protein production from methanol-induced Pichia pastoris cultures is necessary to ensure high productivity rates and high yields of recombinant proteins. We investigated the effects of temperature and different linear or exponential methanol-feeding rates on the production of recombinant Fusarium graminearum galactose oxidase (EC 1.1.3.9) in a P. pastoris Mut+ strain, under regulation of the AOX1 promoter. We found that low exponential methanol feeding led to 1.5-fold higher volumetric productivity compared to high exponential feeding rates. The duration of glycerol feeding did not affect the subsequent product yield, but longer glycerol feeding led to higher initial biomass concentration, which would reduce the oxygen demand and generate less heat during induction. A linear and a low exponential feeding profile led to productivities in the same range, but the latter was characterized by intense fluctuations in the titers of galactose oxidase and total protein. An exponential feeding profile that has been adapted to the apparent biomass concentration results in more stable cultures, but the concentration of recombinant protein is in the same range as when constant methanol feeding is employed. © 2014 The Authors Biotechnology Progress published by Wiley Periodicals, Inc. on behalf of American Institute of Chemical Engineers Biotechnol. Prog., 30:728–735, 2014 PMID:24493559

  20. Revisiting internal gravity waves analysis using GPS RO density profiles: comparison with temperature profiles and application for wave field stability study

    Science.gov (United States)

    Pisoft, Petr; Sacha, Petr; Miksovsky, Jiri; Huszar, Peter; Scherllin-Pirscher, Barbara; Foelsche, Ulrich

    2018-01-01

    We revise selected findings regarding the utilization of Global Positioning System radio occultation (GPS RO) density profiles for the analysis of internal gravity waves (IGW), introduced by Sacha et al. (2014). Using various GPS RO datasets, we show that the differences in the IGW spectra between the dry-temperature and dry-density profiles that were described in the previous study as a general issue are in fact present in one specific data version only. The differences between perturbations in the temperature and density GPS RO profiles do not have any physical origin, and there is not the information loss of IGW activity that was suggested in Sacha et al. (2014). We investigate the previously discussed question of the temperature perturbations character when utilizing GPS RO dry-temperature profiles, derived by integration of the hydrostatic balance. Using radiosonde profiles as a proxy for GPS RO, we provide strong evidence that the differences in IGW perturbations between the real and retrieved temperature profiles (which are based on the assumption of hydrostatic balance) include a significant nonhydrostatic component that is present sporadically and might be either positive or negative. The detected differences in related spectra of IGW temperature perturbations are found to be mostly about ±10 %. The paper also presents a detailed study on the utilization of GPS RO density profiles for the characterization of the wave field stability. We have analyzed selected stability parameters derived from the density profiles together with a study of the vertical rotation of the wind direction. Regarding the Northern Hemisphere the results point to the western border of the Aleutian high, where potential IGW breaking is detected. These findings are also supported by an analysis of temperature and wind velocity profiles. Our results confirm advantages of the utilization of the density profiles for IGW analysis.

  1. Revisiting internal gravity waves analysis using GPS RO density profiles: comparison with temperature profiles and application for wave field stability study

    Directory of Open Access Journals (Sweden)

    P. Pisoft

    2018-01-01

    Full Text Available We revise selected findings regarding the utilization of Global Positioning System radio occultation (GPS RO density profiles for the analysis of internal gravity waves (IGW, introduced by Sacha et al. (2014. Using various GPS RO datasets, we show that the differences in the IGW spectra between the dry-temperature and dry-density profiles that were described in the previous study as a general issue are in fact present in one specific data version only. The differences between perturbations in the temperature and density GPS RO profiles do not have any physical origin, and there is not the information loss of IGW activity that was suggested in Sacha et al. (2014. We investigate the previously discussed question of the temperature perturbations character when utilizing GPS RO dry-temperature profiles, derived by integration of the hydrostatic balance. Using radiosonde profiles as a proxy for GPS RO, we provide strong evidence that the differences in IGW perturbations between the real and retrieved temperature profiles (which are based on the assumption of hydrostatic balance include a significant nonhydrostatic component that is present sporadically and might be either positive or negative. The detected differences in related spectra of IGW temperature perturbations are found to be mostly about ±10 %. The paper also presents a detailed study on the utilization of GPS RO density profiles for the characterization of the wave field stability. We have analyzed selected stability parameters derived from the density profiles together with a study of the vertical rotation of the wind direction. Regarding the Northern Hemisphere the results point to the western border of the Aleutian high, where potential IGW breaking is detected. These findings are also supported by an analysis of temperature and wind velocity profiles. Our results confirm advantages of the utilization of the density profiles for IGW analysis.

  2. Effect of temperature and salinity on stable isotopic composition of shallow water benthic foraminifera: A laboratory culture study

    Digital Repository Service at National Institute of Oceanography (India)

    Kurtarkar, S.R.; Linshy, V.N.; Saraswat, R.; Nigam, R.

    Quantitative estimation of past climatic parameters from stable isotopic composition of foraminifera relies on estimating the precise relationship between stable isotopic composition of the species analyzed and the physico-chemical factors...

  3. Mixed convective/dynamic roll vortices and their effects on initial wind and temperature profiles

    Science.gov (United States)

    Haack, Tracy; Shirer, Hampton N.

    1991-01-01

    The onset and development of both dynamically and convectively forced boundary layer rolls are studied with linear and nonlinear analyses of a truncated spectral model of shallow Boussinesq flow. Emphasis is given here on the energetics of the dominant roll modes, on the magnitudes of the roll-induced modifications of the initial basic state wind and temperature profiles, and on the sensitivity of the linear stability results to the use of modified profiles as basic states. It is demonstrated that the roll circulations can produce substantial changes to the cross-roll component of the initial wind profile and that significant changes in orientation angle estimates can result from use of a roll-modified profile in the stability analysis. These results demonstrate that roll contributions must be removed from observed background wind profiles before using them to investigate the mechanisms underlying actual secondary flows in the boundary layer. The model is developed quite generally to accept arbitrary basic state wind profiles as dynamic forcing. An Ekman profile is chosen here merely to provide a means for easy comparison with other theoretical boundary layer studies; the ultimate application of the model is to study observed boundary layer profiles. Results of the analytic stability analysis are validated by comparing them with results from a larger linear model. For an appropriate Ekman depth, a complete set of transition curves is given in forcing parameter space for roll modes driven both thermally and dynamically. Preferred orientation angles, horizontal wavelengths and propagation frequencies, as well as energetics and wind profile modifications, are all shown to agree rather well with results from studies on Ekman layers as well as with studies on near-neutral and convective atmospheric boundary layers.

  4. Validation of stratospheric temperature profiles from a ground-based microwave radiometer with other techniques

    Science.gov (United States)

    Navas, Francisco; Kämpfer, Niklaus; Haefele, Alexander; Keckhut, Philippe; Hauchecorne, Alain

    2016-04-01

    Vertical profiles of atmospheric temperature trends has become recognized as an important indicator of climate change, because different climate forcing mechanisms exhibit distinct vertical warming and cooling patterns. For example, the cooling of the stratosphere is an indicator for climate change as it provides evidence of natural and anthropogenic climate forcing just like surface warming. Despite its importance, our understanding of the observed stratospheric temperature trend and our ability to test simulations of the stratospheric response to emissions of greenhouse gases and ozone depleting substances remains limited. One of the main reason is because stratospheric long-term datasets are sparse and obtained trends differ from one another. Different techniques allow to measure stratospheric temperature profiles as radiosonde, lidar or satellite. The main advantage of microwave radiometers against these other instruments is a high temporal resolution with a reasonable good spatial resolution. Moreover, the measurement at a fixed location allows to observe local atmospheric dynamics over a long time period, which is crucial for climate research. This study presents an evaluation of the stratospheric temperature profiles from a newly ground-based microwave temperature radiometer (TEMPERA) which has been built and designed at the University of Bern. The measurements from TEMPERA are compared with the ones from other different techniques such as in-situ (radiosondes), active remote sensing (lidar) and passive remote sensing on board of Aura satellite (MLS) measurements. In addition a statistical analysis of the stratospheric temperature obtained from TEMPERA measurements during four years of data has been performed. This analysis evidenced the capability of TEMPERA radiometer to monitor the temperature in the stratosphere for a long-term. The detection of some singular sudden stratospheric warming (SSW) during the analyzed period shows the necessity of these

  5. A Comparison of Thermal Models for Temperature Profiles in Gas-Lift Wells

    Directory of Open Access Journals (Sweden)

    Langfeng Mu

    2018-02-01

    Full Text Available Gas lift is a simple, reliable artificial lift method which is frequently used in offshore oil field developments. In order to enhance the efficiency of production by gas lift, it is vital to exactly predict the distribution of temperature-field for fluid within the wellbore. A new mechanistic model is developed for computing flowing fluid temperature profiles in both conduits simultaneously for a continuous-flow gas-lift operation. This model assumes steady heat transfer in the formation, as well as steady heat transfer in the conduits. A micro-units discrete from the wellbore, whose heat transfer process is analyzed and whose heat transfer equation is set up according to the law of conservation of energy. A simplified algebraic solution to our model is conducted to analyze the temperature profile. Sensitivity analysis was conducted with the new model. The results indicate that mass flow rate of oil and the tubing overall heat transfer coefficient are the main factors that influence the temperature distribution inside the tubing and that the mass flow rate of oil is the main factor affecting temperature distribution in the annulus. Finally, the new model was tested in three various wells and compared with other models. The results showed that the new model is more accurate and provides significant references for temperature prediction in gas lift well.

  6. Analytical solution and computer program (FAST) to estimate fluid fluxes from subsurface temperature profiles

    Science.gov (United States)

    Kurylyk, Barret L.; Irvine, Dylan J.

    2016-02-01

    This study details the derivation and application of a new analytical solution to the one-dimensional, transient conduction-advection equation that is applied to trace vertical subsurface fluid fluxes. The solution employs a flexible initial condition that allows for nonlinear temperature-depth profiles, providing a key improvement over most previous solutions. The boundary condition is composed of any number of superimposed step changes in surface temperature, and thus it accommodates intermittent warming and cooling periods due to long-term changes in climate or land cover. The solution is verified using an established numerical model of coupled groundwater flow and heat transport. A new computer program FAST (Flexible Analytical Solution using Temperature) is also presented to facilitate the inversion of this analytical solution to estimate vertical groundwater flow. The program requires surface temperature history (which can be estimated from historic climate data), subsurface thermal properties, a present-day temperature-depth profile, and reasonable initial conditions. FAST is written in the Python computing language and can be run using a free graphical user interface. Herein, we demonstrate the utility of the analytical solution and FAST using measured subsurface temperature and climate data from the Sendia Plain, Japan. Results from these illustrative examples highlight the influence of the chosen initial and boundary conditions on estimated vertical flow rates.

  7. Temporal profile of body temperature in acute ischemic stroke: relation to infarct size and outcome.

    Science.gov (United States)

    Geurts, Marjolein; Scheijmans, Féline E V; van Seeters, Tom; Biessels, Geert J; Kappelle, L Jaap; Velthuis, Birgitta K; van der Worp, H Bart

    2016-11-21

    High body temperatures after ischemic stroke have been associated with larger infarct size, but the temporal profile of this relation is unknown. We assess the relation between temporal profile of body temperature and infarct size and functional outcome in patients with acute ischemic stroke. In 419 patients with acute ischemic stroke we assessed the relation between body temperature on admission and during the first 3 days with both infarct size and functional outcome. Infarct size was measured in milliliters on CT or MRI after 3 days. Poor functional outcome was defined as a modified Rankin Scale score ≥3 at 3 months. Body temperature on admission was not associated with infarct size or poor outcome in adjusted analyses. By contrast, each additional 1.0 °C in body temperature on day 1 was associated with 0.31 ml larger infarct size (95% confidence interval (CI) 0.04-0.59), on day 2 with 1.13 ml larger infarct size(95% CI, 0.83-1.43), and on day 3 with 0.80 ml larger infarct size (95% CI, 0.48-1.12), in adjusted linear regression analyses. Higher peak body temperatures on days two and three were also associated with poor outcome (adjusted relative risks per additional 1.0 °C in body temperature, 1.52 (95% CI, 1.17-1.99) and 1.47 (95% CI, 1.22-1.77), respectively). Higher peak body temperatures during the first days after ischemic stroke, rather than on admission, are associated with larger infarct size and poor functional outcome. This suggests that prevention of high temperatures may improve outcome if continued for at least 3 days.

  8. Community-level physiological profiles of bacteria and fungi: Plate type and incubation temperature influences on contrasting soils

    Science.gov (United States)

    Aimee T. Classen; Sarah I. Boyle; Kristin E. Haskins; Steven T. Overby; Stephen C. Hart

    2003-01-01

    Temperature sensitivity of community-level physiological profiles (CLPPs) was examined for two semiarid soils from the southwestern United States using five different C-substrate profile microtiter plates (Biolog GN2, GP2, ECO, SFN2, and SFP2) incubated at five different temperature regimes.The CLPPs produced from all plate types were relatively unaffected by these...

  9. THE MAXIMUM EFFECT OF DEEP LAKES ON TEMPERATURE PROFILES – DETERMINATION OF THE GEOTHERMAL GRADIENT

    Directory of Open Access Journals (Sweden)

    Eppelbaum L. V.

    2009-07-01

    Full Text Available Understanding the climate change processes on the basis of geothermal observations in boreholes is an important and at the same time high-intricate problem. Many non-climatic effects could cause changes in ground surface temperatures. In this study we investigate the effects of deep lakes on the borehole temperature profilesobserved within or in the vicinity of the lakes. We propose a method based on utilization of Laplace equation with nonuniform boundary conditions. The proposed method makes possible to estimate the maximum effect of deep lakes (here the term "deep lake" means that long term mean annual temperature of bottom sediments can beconsidered as a constant value on the borehole temperature profiles. This method also allows one to estimate an accuracy of the determination of the geothermal gradient.

  10. Normal range and lateral symmetry in the skin temperature profile of pregnant women

    Science.gov (United States)

    Pereira, Tânia; Nogueira-Silva, Cristina; Simoes, Ricardo

    2016-09-01

    Body skin temperature is a useful parameter for diagnosing diseases and infrared thermography can be a powerful tool in providing important information to detect body temperature changes in a noninvasive way. The aim of this work was to study the pattern of skin temperature during pregnancy, to establish skin temperature reference values and to find correlations between these and the pregnant population characteristics. Sixty-one healthy pregnant women (mean age 30.6 ± 5.1 years) in the 8th-40th gestational week with normal pregnancies were examined in 31 regions of interest (ROI). The ROIs were defined all over the body in order to determine the most influenced by factors such as age or body mass index (BMI). The results obtained in this work highlight that in normal pregnant women the skin temperature is symmetrically distributed, with the symmetrical areas differing less than 0.5 °C , with a mean value of 0.25 ± 0.23 °C . This study identified a significant negative correlation between the BMI and temperature. Age has been shown to have great influence on the skin temperature, with a significant increase of temperature observed with age. This work explores a novel medical application of infrared thermography and provides a characterization of thermal skin profile in human pregnancy for a large set of ROIs while also evaluating the effects of age and BMI.

  11. High-Temperature Thermochemical Storage with Redox-Stable Perovskites for Concentrating Solar Power, CRADA Number: CRD-14-554

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Zhiwen [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-09-05

    As part of a Federal Opportunity Announcement (FOA) Award, the project will be led by Colorado School of Mines (CSM) to explore and demonstrate the efficacy of highly reducible, redox-stable oxides to provide efficient thermochemical energy storage for heat release at temperatures of 900 degrees Celcius or more. NREL will support the material development for its application in a concentrating solar power (CSP) plant. In the project, NREL will provide its inventive system design, chemical looping for CSP, and use it as a platform to accommodate the chemical processes using a cost effective perovskite materials identified by CSM. NREL will design a 5-10kW particle receiver for perovskite reduction to store solar energy and help the development of a fluidized-bed reoxidation reactor and system integration. NREL will develop the demonstration receiver for on-sun test in the 5-10 kWt range in NREL's high flux solar furnace. NREL will assist in system analysis and provide techno-economic inputs for the overall system configuration.

  12. SIMULATION TOOL OF VELOCITY AND TEMPERATURE PROFILES IN THE ACCELERATED COOLING PROCESS OF HEAVY PLATES

    Directory of Open Access Journals (Sweden)

    Antônio Adel dos Santos

    2014-10-01

    Full Text Available The aim of this paper was to develop and apply mathematical models for determining the velocity and temperature profiles of heavy plates processed by accelerated cooling at Usiminas’ Plate Mill in Ipatinga. The development was based on the mathematical/numerical representation of physical phenomena occurring in the processing line. Production data from 3334 plates processed in the Plate Mill were used for validating the models. A user-friendly simulation tool was developed within the Visual Basic framework, taking into account all steel grades produced, the configuration parameters of the production line and these models. With the aid of this tool the thermal profile through the plate thickness for any steel grade and dimensions can be generated, which allows the tuning of online process control models. The simulation tool has been very useful for the development of new steel grades, since the process variables can be related to the thermal profile, which affects the mechanical properties of the steels.

  13. Reconstruction and analysis of temperature and density spatial profiles inertial confinement fusion implosion cores

    International Nuclear Information System (INIS)

    Mancini, R. C.

    2007-01-01

    We discuss several methods for the extraction of temperature and density spatial profiles in inertial confinement fusion implosion cores based on the analysis of the x-ray emission from spectroscopic tracers added to the deuterium fuel. The ideas rely on (1) detailed spectral models that take into account collisional-radiative atomic kinetics, Stark broadened line shapes, and radiation transport calculations, (2) the availability of narrow-band, gated pinhole and slit x-ray images, and space-resolved line spectra of the core, and (3) several data analysis and reconstruction methods that include a multi-objective search and optimization technique based on a novel application of Pareto genetic algorithms to plasma spectroscopy. The spectroscopic analysis yields the spatial profiles of temperature and density in the core at the collapse of the implosion, and also the extent of shell material mixing into the core. Results are illustrated with data recorded in implosion experiments driven by the OMEGA and Z facilities

  14. An extended Kalman-Bucy filter for atmospheric temperature profile retrieval with a passive microwave sounder

    Science.gov (United States)

    Ledsham, W. H.; Staelin, D. H.

    1978-01-01

    An extended Kalman-Bucy filter has been implemented for atmospheric temperature profile retrievals from observations made using the Scanned Microwave Spectrometer (SCAMS) instrument carried on the Nimbus 6 satellite. This filter has the advantage that it requires neither stationary statistics in the underlying processes nor linear production of the observed variables from the variables to be estimated. This extended Kalman-Bucy filter has yielded significant performance improvement relative to multiple regression retrieval methods. A multi-spot extended Kalman-Bucy filter has also been developed in which the temperature profiles at a number of scan angles in a scanning instrument are retrieved simultaneously. These multi-spot retrievals are shown to outperform the single-spot Kalman retrievals.

  15. Experimental and numerical results for CO2 concentration and temperature profiles in an occupied room

    Science.gov (United States)

    Cotel, Aline; Junghans, Lars; Wang, Xiaoxiang

    2014-11-01

    In recent years, a recognition of the scope of the negative environmental impact of existing buildings has spurred academic and industrial interest in transforming existing building design practices and disciplinary knowledge. For example, buildings alone consume 72% of the electricity produced annually in the United States; this share is expected to rise to 75% by 2025 (EPA, 2009). Significant reductions in overall building energy consumption can be achieved using green building methods such as natural ventilation. An office was instrumented on campus to acquire CO2 concentrations and temperature profiles at multiple locations while a single occupant was present. Using openFOAM, numerical calculations were performed to allow for comparisons of the CO2 concentration and temperature profiles for different ventilation strategies. Ultimately, these results will be the inputs into a real time feedback control system that can adjust actuators for indoor ventilation and utilize green design strategies. Funded by UM Office of Vice President for Research.

  16. Formula for radial profiles of temperature in steam-liquid sodium reactive jets

    International Nuclear Information System (INIS)

    Hobbes, P.; Mora-Perez, J.L.; Carreau, J.L.; Gbahoue, L.; Roger, F.

    1987-01-01

    One of the important problems of the study of distribution of temperatures in the reactive steam-liquid sodium jet rests in the mathematical formulation of their radial effects. During the experiment, two forms have been brought to light: from a certain distance of the injector, the radial distribution of temperature can be represented, in a classical way, by an error function curve; close to the injector, the radial profile allows for a minimum located on the axis of the jet. An energy balance permits, by dividing the jet in three parts: a central nucleus composed of practically pure gas, a gas ring plus drops and a liquid peripheral area plus bubbles, to obtain a mathematical formulation of the profiles, close to the injection which accounts quite well for the experimental points and their form

  17. Modelling of composition and stress profiles in low temperature surface engineered stainless steel

    DEFF Research Database (Denmark)

    Jespersen, Freja Nygaard; Hattel, Jesper Henri; Somers, Marcel A. J.

    2015-01-01

    stresses are introduced in the developing case, arising from the volume expansion that accompanies the dissolution of high interstitial contents in expanded austenite. Modelling of the composition and stress profiles developing during low temperature surface engineering from the processing parameters...... temperature, time and gas composition is a prerequisite for targeted process optimization. A realistic model to simulate the developing case has to take the following influences on composition and stress into account: - a concentration dependent diffusion coefficient - trapping of nitrogen by chromium atoms...... - the effect of residual stress on diffusive flux - the effect of residual stress on solubility of interstitials - plastic accommodation of residual stress. The effect of all these contributions on composition and stress profiles will be addressed....

  18. Monitoring of temperature profiles and surface morphologies during laser sintering of alumina ceramics

    Directory of Open Access Journals (Sweden)

    Bin Qian

    2014-06-01

    Full Text Available Additive manufacturing of alumina by laser is a delicate process and small changes of processing parameters might cause less controlled and understood consequences. The real-time monitoring of temperature profiles, spectrum profiles and surface morphologies were evaluated in off-axial set-up for controlling the laser sintering of alumina ceramics. The real-time spectrometer and pyrometer were used for rapid monitoring of the thermal stability during the laser sintering process. An active illumination imaging system successfully recorded the high temperature melt pool and surrounding area simultaneously. The captured images also showed how the defects form and progress during the laser sintering process. All of these real-time monitoring methods have shown a great potential for on-line quality control during laser sintering of ceramics.

  19. Flexibl Pavement Analysis Considering Temperature Profile and Anisotropy Behavior in Hot Mix Asphalt Layer

    Directory of Open Access Journals (Sweden)

    Choi Joonho

    2011-12-01

    Full Text Available A three Dimensional finite element model (FEM incorporating the anisotropic properties and temperature profile of hot mix asphalt (HMA pavement was developed to predict the structural responses of HMA pavement subject to heavy loads typically encountered in the field. In this study, ABAQUS was adopted to model the stress and strain relationships within the pavement structure. The results of the model were verified using data collected from the Korean Highway Corporation Test Road (KHCTR. The results demonstrated that both the base course and surface course layers follow the anisotropic behavior and the incorporation of the temperature profile throughout the pavement has a substantial effect on the pavement response predictions that impact pavement design. The results also showed that the anisotropy level of HMA and base material can be reduced to as low as 80% and 15% as a result of repeated loading, respectively.

  20. Lipid content and fatty acid profile during lake whitefish embryonic development at different incubation temperatures.

    Science.gov (United States)

    Mueller, Casey A; Doyle, Liam; Eme, John; Manzon, Richard G; Somers, Christopher M; Boreham, Douglas R; Wilson, Joanna Y

    2017-01-01

    Lipids serve as energy sources, structural components, and signaling molecules during fish embryonic development, and utilization of lipids may vary with temperature. Embryonic energy utilization under different temperatures is an important area of research in light of the changing global climate. Therefore, we examined percent lipid content and fatty acid profiles of lake whitefish (Coregonus clupeaformis) throughout embryonic development at three incubation temperatures. We sampled fertilized eggs and embryos at gastrulation, eyed and fin flutter stages following chronic incubation at temperatures of 1.8, 4.9 and 8.0°C. Hatchlings were also sampled following incubation at temperatures of 3.3, 4.9 and 8.0°C. Fertilized eggs had an initial high percentage of dry mass composed of lipid (percent lipid content; ~29%) consisting of ~20% saturated fatty acids (SFA), ~32% monounsaturated fatty acids (MUFA), ~44% polyunsaturated fatty acids (PUFA), and 4% unidentified. The most abundant fatty acids were 16:0, 16:1, 18:1(n-9c), 20:4(n-6), 20:5(n-3) and 22:6(n-3). This lipid profile matches that of other cold-water fish species. Percent lipid content increased during embryonic development, suggesting protein or other yolk components were preferentially used for energy. Total percentage of MUFA decreased during development, which indicated MUFA were the primary lipid catabolized for energy during embryonic development. Total percentage of PUFA increased during development, driven largely by an increase in 22:6(n-3). Temperature did not influence percent lipid content or percent MUFA at any development stage, and had inconsistent effects on percent SFA and percent PUFA during development. Thus, lake whitefish embryos appear to be highly adapted to low temperatures, and do not alter lipids in response to temperature within their natural incubation conditions. Copyright © 2016 Elsevier Inc. All rights reserved.

  1. Modelling and experimental study of temperature profiles in cw laser diode bars

    Science.gov (United States)

    Bezotosnyi, V. V.; Gordeev, V. P.; Krokhin, O. N.; Mikaelyan, G. T.; Oleshchenko, V. A.; Pevtsov, V. F.; Popov, Yu M.; Cheshev, E. A.

    2018-02-01

    Three-dimensional simulation is used to theoretically assess temperature profiles in proposed 10-mm-wide cw laser diode bars packaged in a standard heat spreader of the C - S mount type with the aim of raising their reliable cw output power. We obtain calculated temperature differences across the emitting aperture and along the cavity. Using experimental laser bar samples with up to 60 W of cw output power, the emission spectra of individual clusters are measured at different pump currents. We compare and discuss the simulation results and experimental data.

  2. Atmospheric pressure and temperature profiling using near IR differential absorption lidar

    Science.gov (United States)

    Korb, C. L.; Schwemmer, G. K.; Dombrowski, M.; Weng, C. Y.

    1983-01-01

    The present investigation is concerned with differential absorption lidar techniques for remotely measuring the atmospheric temperature and pressure profile, surface pressure, and cloud top pressure-height. The procedure used in determining the pressure is based on the conduction of high-resolution measurements of absorption in the wings of lines in the oxygen A band. Absorption with respect to these areas is highly pressure sensitive in connection with the mechanism of collisional line broadening. The method of temperature measurement utilizes a determination of the absorption at the center of a selected line in the oxygen A band which originates from a quantum state with high ground state energy.

  3. Distinction of gases with a semiconductor sensor depending on the scanning profile of a cyclic temperature.

    Science.gov (United States)

    Nakata, Satoshi; Okunishi, Hirokazu; Nakashima, Yusuke

    2006-01-01

    A gas-sensing system based on a dynamic nonlinear response is reported to improve the selectivity in the sensor response toward sample gases. A cyclic temperature composed of fundamental and second harmonics was applied to a SnO(2) semiconductor gas sensor and the resulting conductance of the sensor was analyzed by fast Fourier transformation (FFT). The dynamic nonlinear responses to the gas species were further characterized depending on the scanning profile of the temperature. These characteristic sensor responses under the application of second-harmonic perturbation were theoretically considered based on a reaction-diffusion model for the semiconductor surface.

  4. Stabilization of a magnetic island by localized heating in a tokamak with stiff temperature profile

    Science.gov (United States)

    Maget, Patrick; Widmer, Fabien; Février, Olivier; Garbet, Xavier; Lütjens, Hinrich

    2018-02-01

    In tokamaks plasmas, turbulent transport is triggered above a threshold in the temperature gradient and leads to stiff profiles. This particularity, neglected so far in the problem of magnetic island stabilization by a localized heat source, is investigated analytically in this paper. We show that the efficiency of the stabilization is deeply modified compared to the previous estimates due to the strong dependence of the turbulence level on the additional heat source amplitude inside the island.

  5. Differential absorption lidars for remote sensing of atmospheric pressure and temperature profiles

    Science.gov (United States)

    Korb, C. Laurence; Schwemmer, Geary K.; Famiglietti, Joseph; Walden, Harvey; Prasad, Coorg

    1995-01-01

    A near infrared differential absorption lidar technique is developed using atmospheric oxygen as a tracer for high resolution vertical profiles of pressure and temperature with high accuracy. Solid-state tunable lasers and high-resolution spectrum analyzers are developed to carry out ground-based and airborne measurement demonstrations and results of the measurements presented. Numerical error analysis of high-altitude airborne and spaceborne experiments is carried out, and system concepts developed for their implementation.

  6. The numeric modelling of the temperature profile of moulded piece in thermostatic mould form

    OpenAIRE

    A. Gnatowski; T. Stachowiak

    2011-01-01

    Purpose: The project shows the results of researches of the flow of polymer materials during the filling the mould. The main purpose of carry out research was estimate the influence thermal conditions of the mould on the temperature profile of injection moulded parts. Design/methodology/approach: The most important issues like injection moulding process and the conditions of this process are covered in article. Moreover, the computer system used in the process of material conversion like Cadm...

  7. Water surface temperature profiles for the Rhine River derived from Landsat ETM+ data

    Science.gov (United States)

    Fricke, Katharina; Baschek, Björn

    2013-10-01

    Water temperature influences physical and chemical parameters of rivers and streams and is an important parameter for water quality. It is a crucial factor for the existence and the growth of animal and plant species in the river ecosystem. The aim of the research project "Remote sensing of water surface temperature" at the Federal Institute of Hydrology (BfG), Germany, is to supplement point measurements of water temperature with remote sensing methodology. The research area investigated here is the Upper and Middle Rhine River, where continuous measurements of water temperature are already available for several water quality monitoring stations. Satellite imagery is used to complement these point measurements and to generate longitudinal temperature profiles for a better systematic understanding of the changes in river temperature along its course. Several products for sea surface temperature derived from radiances in the thermal infrared are available, but for water temperature from rivers less research has been carried out. Problems arise from the characteristics of the river valley and morphology and the proximity to the riverbank. Depending on the river width, a certain spatial resolution of the satellite images is necessary to allow for an accurate identification of the river surface and the calculation of water temperature. The bands from the Landsat ETM+ sensor in the thermal infrared region offer a possibility to extract the river surface temperatures (RST) of a sufficiently wide river such as the Rhine. Additionally, problems such as cloud cover, shadowing effects, georeferencing errors, different emissivity of water and land, scattering of thermal radiation, adjacency and mixed pixel effects had to be accounted for and their effects on the radiance temperatures will be discussed. For this purpose, several temperature data sets derived from radiance and in situ measurements were com- pared. The observed radiance temperatures are strongly influenced by

  8. A novel model for predicting the temperature profile in gas lift wells

    Directory of Open Access Journals (Sweden)

    Mohammad Reza Mahdiani

    2016-12-01

    Full Text Available One of the most common methods for calculating the production oil rate in a gas lift well is nodal analysis. This manner is an accurate one, but unfortunately it is very time consuming and slow. In some modern studies in petroleum engineering such as close loop control of the wells this slowness makes it impossible to have an online optimization. In fact, before the end of the optimization the input parameters have changed. Thus having a faster model is necessary specially in some of the new studies. One of the sources of slowness of the nodal analysis is the temperature profile estimation of the wells. There are two general approaches for temperature profile estimation, some like heat balance are accurate but slow. Others, similar to linear profile assumption are fast but inaccurate and usually are not used commonly. Here, as a new approach, a combination model of heat balance and linear temperature profile estimation has represented which makes the nodal analysis three times faster and it is as accurate as heat balance calculations. To create this, two points (gas injection point and end of tubing are selected, then using heat balance equations the temperature of those two points are calculated. In normal nodal analysis the temperature of each wanted point in the well is estimated by heat balance and it is the source of slowness but here just two points are calculated using those complex equations. It seems that between these points assuming a linear temperature profile is reasonable because the parameters of the well and production such as physical tubing, and casing shape and properties and gas oil ratio are constants. But of course, it still has some deviation from the complete method of heat balance which using regression and assigning a coefficient to the model even this much of the deviation could be overcame. Finally, the model was tested in various wells and it was compared with the normal nodal analysis with complete heat balance

  9. Temperature profiles of antibiotic-containing elastomeric infusion devices used by ambulatory care patients.

    Science.gov (United States)

    Docherty, Toni; Montalto, Michael; Leslie, Joni; King, Katrina; Niblett, Suzanne; Garrett, Tim

    2017-07-01

    The temperature profiles of antibiotic-containing elastomeric infusion devices used by ambulatory care patients under various environmental conditions were evaluated. A prospective, descriptive survey of temperature exposure was conducted in 4 publically funded hospitals. Over a 12-month period, electronic temperature-recording devices were attached to the antibiotic infusion devices (infusers) of prospectively randomized hospital-in-the-home (HITH) participants. Temperatures were recorded immediately after infuser connection and every 5 minutes thereafter for 24 hours. A structured data collection form was used to collect information on basic clinical and demographic characteristics and aspects of daily living (i.e., how and where the infuser was carried during the day, times the participant went to and arose from bed, location of the infuser while sleeping, and dates and times the infuser was connected and disconnected). A total of 115 patients successfully completed the study (17-91 years old, 55% males). A total of 31,298 temperature readings were collected. The storage location of the infuser did not influence daytime readings. However, the overnight storage location did have a significant impact on the temperatures recorded overnight. The mean temperatures of infusers stored on the bed or on the body overnight were significantly higher than those for infusers stored away from the bed. Diurnal and seasonal influences were also detected. Significantly warmer temperatures were recorded in afternoons and evenings and during the summer months. Antibiotics administered to HITH patients via continuous infusion were frequently exposed to temperatures in excess of 25 °C. Specific patient behaviors and seasonal and chronological factors influenced temperatures. The findings challenge the validity of current fixed-temperature models for testing stability, which do not reflect conditions found in clinical practice. Copyright © 2017 by the American Society of Health

  10. Association between mutation spectra and stable and unstable DNA adduct profiles in Salmonella for benzo[a]pyrene and dibenzo[a,l]pyrene

    Energy Technology Data Exchange (ETDEWEB)

    DeMarini, David M., E-mail: demarini.david@epa.gov [Integrated Systems Toxicology Division, U.S. Environmental Protection Agency, Research Triangle Park, NC 27711 (United States); Hanley, Nancy M.; Warren, Sarah H.; Adams, Linda D.; King, Leon C. [Integrated Systems Toxicology Division, U.S. Environmental Protection Agency, Research Triangle Park, NC 27711 (United States)

    2011-09-01

    Highlights: {yields} Benzo[a]pyrene (BP) induces stable DNA adducts and mutations primarily at guanine. {yields} Dibenzo[a,l]pyrene (DBP) induces them primarily at adenine. {yields} BP induces abasic sites, but DBP does not in the Salmonella mutagenicity assay. {yields} Stable DNA adducts alone appear to account for the mutation spectrum of DBP. {yields} Stable DNA adducts and possibly abasic sites account for the mutation spectrum of BP. - Abstract: Benzo[a]pyrene (BP) and dibenzo[a,l]pyrene (DBP) are two polycyclic aromatic hydrocarbons (PAHs) that exhibit distinctly different mutagenicity and carcinogenicity profiles. Although some studies show that these PAHs produce unstable DNA adducts, conflicting data and arguments have been presented regarding the relative roles of these unstable adducts versus stable adducts, as well as oxidative damage, in the mutagenesis and tumor-mutation spectra of these PAHs. However, no study has determined the mutation spectra along with the stable and unstable DNA adducts in the same system with both PAHs. Thus, we determined the mutagenic potencies and mutation spectra of BP and DBP in strains TA98, TA100 and TA104 of Salmonella, and we also measured the levels of abasic sites (aldehydic-site assay) and characterized the stable DNA adducts ({sup 32}P-postlabeling/HPLC) induced by these PAHs in TA104. Our results for the mutation spectra and site specificity of stable adducts were consistent with those from other systems, showing that DBP was more mutagenic than BP in TA98 and TA100. The mutation spectra of DBP and BP were significantly different in TA98 and TA104, with 24% of the mutations induced by BP in TA98 being complex frameshifts, whereas DBP produced hardly any of these mutations. In TA104, BP produced primarily GC to TA transversions, whereas DBP produced primarily AT to TA transversions. The majority (96%) of stable adducts induced by BP were at guanine, whereas the majority (80%) induced by DBP were at adenine

  11. Profiling B-type natriuretic peptide in a stable heart failure population: a valuable adjunct to care.

    LENUS (Irish Health Repository)

    Jan, A

    2012-02-01

    AIM: To examine the prognostic importance of absolute values and change in values of BNP in patients with stable heart failure (HF). METHODS: Five-hundred and fifty-nine patients attending a disease management programme were categorized into tertiles of BNP (group 1; <\\/= 95 pg\\/ml, group 2; 96-249 pg\\/ml and group 3; >\\/= 250 pg\\/ml). A change in BNP between two stable visits was recorded. Patients were followed up for 1 year for death and a composite morbidity measure of HF hospitalization, all-cause hospitalization, unscheduled visits for clinical deterioration(UC) of HF using survival analysis. RESULTS: The risk of the combined morbidity outcome increased with increasing tertiles of BNP (Log rank = 17.8 (2), p < 0.001). Furthermore, a 50 and 25% increase in BNP predicted morbidity in stable HF patients with an initial BNP > 200 pg\\/ml (p = 0.02) and > 450 pg\\/ml (p = 0.03), respectively. CONCLUSION: In a stable community HF population, an elevated BNP or an increase in BNP predicts an adverse prognosis thereby potentially identifying a population in need of closer clinical follow-up.

  12. TSTAR: Stratospheric temperature and pressure profiles retrievals using on-orbit star pairs observation.

    Science.gov (United States)

    Gordley, L. L.; Lachance, R. L.; Marshall, B. T.; Stockwell, B.; Wan, K.

    2015-12-01

    TSTAR (Temperature profiles using Star Pairs) is a revolutionary sensor which observes occulting star pairs from orbiting sensors. As star pairs are being compressed during descent through the atmospheric limb, refraction angle change is computed for deducing density profile, which in turn by inversion allows getting stratospheric temperature and pressure profiles. This instrument is intended to be a new source of global high altitude temperature fields, providing global coverage from cloud-top (tropopause ≈8-17 km) to 45 km at a horizontal resolution better than 100 km. Such a system works with standard visible cameras, not requiring complex cooled detectors. Moreover, refractive angle resolution is not limited by the optical resolution of the instrument, and by using orbital mechanics, accurate computation can be done without precise spacecraft attitude knowledge. This technically simple, compact, and low cost hardware will also provide a valuable data set for improving weather forecasting. This concept has just completed the conceptual phase and feasibility analysis. The next step is to form key collaborations for developing a demonstration sensor. In due course, as few as a dozen of nanosatellites could get the Earth covered.

  13. Assessment of NOAA NUCAPS upper air temperature profiles using COSMIC GPS radio occultation and ARM radiosondes

    Science.gov (United States)

    Feltz, M. L.; Borg, L.; Knuteson, R. O.; Tobin, D.; Revercomb, H.; Gambacorta, A.

    2017-09-01

    The U.S. National Oceanic and Atmospheric Administration (NOAA) recently began operational processing to derive vertical temperature profiles from two new sensors, Cross-Track Infrared Sounder and Advanced Technology Microwave Sounder, which were developed for the next generation of U.S. weather satellites. The NOAA-Unique Combined Atmospheric Processing System (NUCAPS) has been developed by NOAA to routinely process data from future Joint Polar Satellite System operational satellites and the preparatory Suomi-NPP satellite. This paper assesses the NUCAPS vertical temperature profile product from the upper troposphere into the middle stratosphere using radiosonde and GPS radio occultation (RO) data. Radiosonde data from the Department of Energy Atmospheric Radiation Measurement (ARM) program are=] compared to both the NUCAPS and GPS RO temperature products to evaluate bias and RMS errors. At all three fixed ARM sites for time periods investigated the NUCAPS temperature in the 100-40 hPa range is found to have an average bias to the radiosondes of less than 0.45 K and an RMS error of less than 1 K when temperature averaging kernels are applied. At a 95% confidence level, the radiosondes and RO were found to agree within 0.4 K at the North Slope of Alaska site and within 0.83 K at Southern Great Plains and Tropical Western Pacific. The GPS RO-derived dry temperatures, obtained from the University Corporation for Atmospheric Research Constellation Observing System for Meteorology, Ionosphere, and Climate (COSMIC) mission, are used as a common reference for the intercomparison of NUCAPS temperature products to similar products produced by NASA from Atmospheric Infrared Sounder (AIRS) and by European Organisation for the Exploitation of Meteorological Satellites from MetOp-B Infrared Atmospheric Sounding Interferometer (IASI). For seasonal and zonal scales, the NUCAPS agreement with AIRS and IASI is less than 0.5 K after application of averaging kernels.

  14. Wound temperature profiles of coaxial mini-incision versus sleeveless microincision phacoemulsification.

    Science.gov (United States)

    Belkin, Avner; Abulafia, Adi; Michaeli, Adi; Ofir, Shay; Assia, Ehud I

    2017-04-01

    Temperature profiles at the corneal wound of coaxial mini-incision (2.4 mm) cataract surgery and sleeveless microincision (1.1 mm) cataract surgery were compared. Prospective, controlled, paired-eye clinical trial conducted in a tertiary care hospital. Twenty patients with mild-to-moderate bilateral nuclear sclerotic cataract. Twenty patients underwent bilateral cataract surgery within a 1-month period. One eye was operated on by conventional coaxial mini-incision (2.4 mm) phacoemulsification. The second eye underwent microincision surgery by using a naked phacoemulsification tip and a specialized 19-gauge anterior chamber maintainer as the sole fluid source (three-port microincision cataract surgery technique). Patients had moderate bilateral cataracts with no other anterior segment pathology. Temperature at the corneal wound was constantly recorded by using infrared thermal imaging. Temperatures at the corneal wound. Mean temperatures at the corneal surgical wound were not significantly different between the coaxial and sleeveless groups (31.1 °C ± 2.3 vs. 31.0 °C ± 2. 0; P = 0.89). There was also no difference in maximum temperatures reached during phaco-emulsification. Temperatures did not rise above 40 °C during any surgery, and there were no corneal burns. Final visual acuity and intraoperative and postoperative complication rates were similar between the two groups. The temperature profile at the surgical wound using a microincisional sleeveless phacoemulsification technique is comparable with that of the conventional coaxial mini-incision method. © 2016 Royal Australian and New Zealand College of Ophthalmologists.

  15. Assimilation of Quality Controlled AIRS Temperature Profiles using the NCEP GFS

    Science.gov (United States)

    Susskind, Joel; Reale, Oreste; Iredell, Lena; Rosenberg, Robert

    2013-01-01

    We have previously conducted a number of data assimilation experiments using AIRS Version-5 quality controlled temperature profiles as a step toward finding an optimum balance of spatial coverage and sounding accuracy with regard to improving forecast skill. The data assimilation and forecast system we used was the Goddard Earth Observing System Model , Version-5 (GEOS-5) Data Assimilation System (DAS), which represents a combination of the NASA GEOS-5 forecast model with the National Centers for Environmental Prediction (NCEP) operational Grid Point Statistical Interpolation (GSI) global analysis scheme. All analyses and forecasts were run at a 0.5deg x 0.625deg spatial resolution. Data assimilation experiments were conducted in four different seasons, each in a different year. Three different sets of data assimilation experiments were run during each time period: Control; AIRS T(p); and AIRS Radiance. In the "Control" analysis, all the data used operationally by NCEP was assimilated, but no AIRS data was assimilated. Radiances from the Aqua AMSU-A instrument were also assimilated operationally by NCEP and are included in the "Control". The AIRS Radiance assimilation adds AIRS observed radiance observations for a select set of channels to the data set being assimilated, as done operationally by NCEP. In the AIRS T(p) assimilation, all information used in the Control was assimilated as well as Quality Controlled AIRS Version-5 temperature profiles, i.e., AIRS T(p) information was substituted for AIRS radiance information. The AIRS Version-5 temperature profiles were presented to the GSI analysis as rawinsonde profiles, assimilated down to a case-by-case appropriate pressure level p(sub best) determined using the Quality Control procedure. Version-5 also determines case-by-case, level-by-level error estimates of the temperature profiles, which were used as the uncertainty of each temperature measurement. These experiments using GEOS-5 have shown that forecasts

  16. Three-Dimensional Temperature and Wind Profiles Obtained Using UAV-Based Acoustic Atmospheric Tomography

    Science.gov (United States)

    Finn, A.

    2017-12-01

    The natural sound generated by an unmanned aerial vehicle is used in conjunction with tomography to remotely sense atmospheric temperature and wind profiles simultaneously. Sound fields recorded onboard the aircraft and by an array of microphones on the ground are compared and converted to sound speed estimates for the ray paths intersecting the intervening medium. Tomographic inversion is then used to transform these sound speed values into vertical cross-sections and 3D volumes of virtual temperature and wind vectors, which enables the atmosphere to be visualised and monitored over time up to altitudes of 1,200m and over baselines of up to 600m. This paper reports on results from two short campaigns during which 2D and 3D profiles of wind and temperature obtained in this way were compared to: measurements taken by co-located mid-range Doppler SODAR and LIDAR; and temperature measurements made by instruments carried by unmanned aircraft flying through the intervening atmosphere. Large eddy simulation of daytime atmospheric boundary layers were also used to examine the anticipated performance of the instruments and the nature of any errors. The observations obtained using all systems are shown to correspond closely.

  17. Observational results of microwave temperature profile measurements from the airborne Antarctic ozone experiment

    Science.gov (United States)

    Gary, Bruce L.

    1988-01-01

    The Microwave Temperature Profiler, MTP, is installed on NASA's ER-2 aircraft. MTP measures profiles of air temperature versus altitude. Temperatures are obtained every 13.7 seconds for 15 altitudes in an altitude region that is approximately 5 km thick (at high flight levels). MTP is a passive microwave radiometer, operating at the frequencies 57.3 and 58.8 GHz. Thermal emission from oxygen molecules provides the signal that is converted to air temperature. MTP is unique in that it is the only airborne instrument of its kind. The MTP instrument was used during the Airborne Antarctic Ozone Experiment, AAOE, to enable potential vorticity to be measured along the flight track. Other uses for the MTP data have become apparent. The most intriguing unexpected use is the detection and characterization of mountain waves that were encountered during flights over the Palmer Peninsula. Mountain waves that propagate into the polar vortex may have implications for the formation of the ozone hole. Upward excursions of air parcels lead to a brief cooling. This can begin the process of cloud formation. It is important to determine how much additional formation of polar stratospheric cloud (PSC) material is possible by the passage of air parcels through a mountain wave pattern that endures for long periods. Other mountain wave effects have been suggested, such as a speeding up of the vortex, and a consequent cooling of large air volumes (which in turn might add to PSC production).

  18. Eutectic Gallium-Indium (EGaIn) : A Liquid Metal Alloy for the Formation of Stable Structures in Microchannels at Room Temperature

    NARCIS (Netherlands)

    Dickey, Michael D.; Chiechi, Ryan C.; Larsen, Ryan J.; Weiss, Emily A.; Weitz, David A.; Whitesides, George M.

    2008-01-01

    This paper describes the rheological behavior of the liquid metal eutectic gallium-indium (EGaIn) as it is injected into microfluidic channels to form stable microstructures of liquid metal. EGaIn is well-suited for this application because of its rheological properties at room temperature: it

  19. High-Temperature Equilibrium Isotope Fractionation of Non-Traditional Stable Isotopes: Experiments, Theory, and Applications (Invited)

    Science.gov (United States)

    Young, E. D.; Lazar, G. C.; Macris, C. A.; Manning, C. E.; Schauble, E. A.; Shahar, A.

    2013-12-01

    Experiments are crucial for validating our understanding of stable isotope fractionation at high temperatures. The three-isotope method has been applied with success in the Si, Mg, Fe, and Ni isotope systems to date. The results of these experiments can be compared with expectations from theory and measurements of natural samples. Qualitative insights into the partitioning of heavy and light isotopes between mineral phases are gained by treating the force constant for relevant bonds, Kf j, as electrostatic in origin. The ionic model, based on the mean bond strength as defined by Pauling, has obvious limitations but is useful for rationalizing structures and site occupancies in silicates and oxide minerals and is equally useful in formulating expectations for isotope fractionation between phases. In some cases, as in Fe isotopes in spinels, the expectations are contrary to predictions based on modeling but similar to observations in natural samples. Experimental verification is required. The force constant for a bond between cation i (Mg, Fe, etc.) and anion j (e.g., O) can be written in terms of mean bond strengths si and sj (as defined by Pauling) as Kf,ij = sisj e2 (1-n)/(4 π ɛο r3ij ) where ɛo is the electric constant (vacuum permittivity for simplicity), e is the charge of an electron, n is the exponent in the Born-Mayer formulation for ion repulsion (Born and Mayer 1932), and rij is the interatomic spacing. This equation shows explicitly that larger values for the force constant Kf correspond to smaller coordination numbers (via si and sj). We therefore expect an inverse relationship between isotope ratios (heavy/light) and coordination of its oxygen bond partners in silicate and oxides minerals and this is verified in mantle minerals. Our work with Fe isotope partitioning in mantle spinels suggests that coordination may be equally important as oxidation state, recognizing that these distinctions are not orthogonal. Recent work on the Mg isotopic

  20. Athletes trained using stable compared to unstable surfaces exhibit distinct postural control profiles when assessed by traditional and nonlinear measures.

    Science.gov (United States)

    Powell, Douglas W; Williams, D S Blaise

    2015-12-01

    Athletes are assumed to exhibit better balance than non-athletes; however, few studies have examined the role of different types of sports on balance measures. Two athlete groups that experience divergent sport-specific balance training are stable- (i.e. basketball) and unstable-surface athletes (i.e. surfers). The purpose of this study was to quantify the effect of stable- compared to unstable-surface sports on postural stability. Eight non-athletes (NON), eight stable-surface athletes (SSA) and eight unstable-surface athletes (USA) performed five 20-s quiet standing trials while ground reaction forces were recorded. Approximate entropy (ApEn), total excursion and root mean square distances (RMS) of the center of pressure position were calculated. Univariate ANOVAs with post hoc tests were conducted for each variable. ApEn values were lower in SSA compared to NON in the ML direction (p=0.012) and USA had lower ApEn values compared to SSA in the AP direction (p=0.036). The USA had smaller AP RMS compared to SSA (p=0.002) while the USA had greater ML RMS (p=0.008) and resultant RMS values compared to SSA (p=0.025). These data suggest that USA and SSA may exhibit direction-specific differences in balance strategy due to feedback paradigm. Copyright © 2015 Elsevier B.V. All rights reserved.

  1. Measurements of electron density and temperature profiles in a gas blanket experiment

    International Nuclear Information System (INIS)

    Kuthy, A.

    1979-02-01

    Radial profiles of electron density, temperature and H sub(β) intensity are presented for the rotating plasma device F-1. The hydrogen filling pressure, the average magnetic field strength at the midplane, and the power input to the discharge have been varied in the ranges 10-100 mTorr, 0.25-0.5 Tesla, and 0.1 to 1.5 MW, respectively. These experiments have been performed with the main purpose of studying the gas blanket (cold-mantle) state of the plasma. It is shown, that a simple spectroscopic method can be used to derive the radial distribution of the electron temperature in such plasmas. The observed peak temperatures and densities are in agreement with earlier theoretical estimates. (author)

  2. Old and stable soil organic matter is not necessarily chemically recalcitrant: Implications for modeling concepts and temperature sensitivity

    Energy Technology Data Exchange (ETDEWEB)

    Kleber, M.; Nico, P.S.; Plante, A.; Filley, T.; Kramer, M.; Swanston, C.; Sollins, P.

    2010-03-01

    Soil carbon turnover models generally divide soil carbon into pools with varying intrinsic decomposition rates. Although these decomposition rates are modified by factors such as temperature, texture, and moisture, they are rationalized by assuming chemical structure is a primary controller of decomposition. In the current work, we use near edge X-ray absorption fine structure (NEXAFS) spectroscopy in combination with differential scanning calorimetry (DSC) and alkaline cupric oxide (CuO) oxidation to explore this assumption. Specifically, we examined material from the 2.3-2.6 kg L{sup -1} density fraction of three soils of different type (Oxisol, Alfisol, Inceptisol). The density fraction with the youngest {sup 14}C age (Oxisol, 107 years) showed the highest relative abundance of aromatic groups and the lowest O-alkyl C/aromatic C ratio as determined by NEXAFS. Conversely, the fraction with the oldest C (Inceptisol, 680 years) had the lowest relative abundance of aromatic groups and highest O-alkyl C/aromatic C ratio. This sample also had the highest proportion of thermally labile materials as measured by DSC, and the highest ratio of substituted fatty acids to lignin phenols as indicated by CuO oxidation. Therefore, the organic matter of the Inceptisol sample, with a {sup 14}C age associated with 'passive' pools of carbon (680 years), had the largest proportion of easily metabolizable organic molecules with low thermodynamic stability, whereas the organic matter of the much younger Oxisol sample (107 years) had the highest proportion of supposedly stable organic structures considered more difficult to metabolize. Our results demonstrate that C age is not necessarily related to molecular structure or thermodynamic stability, and we suggest that soil carbon models would benefit from viewing turnover rate as codetermined by the interaction between substrates, microbial actors, and abiotic driving variables. Furthermore, assuming that old carbon is composed

  3. Effect of temperature on growth and fatty acids profile of the biodiesel producing microalga Scenedesmus acutus

    Directory of Open Access Journals (Sweden)

    El-Sheekh, M.

    2017-01-01

    Full Text Available Description of the subject. The present study examined the effect of temperature (15, 20, 25, 30, 35 and 40 °C on biomass, esterified fatty acids content and fatty acid productivity of Scenedesmus acutus. Objectives. This work aimed to study the effect of variation in temperature on lipid productivity and fatty acid profiles of S. acutus as a feedstock for biodiesel production. Method. The alga was grown under different temperatures and its biomass, as well as fatty acid content and composition, were determined. Results. The maximum growth rate of S. acutus was achieved at 30 °C , but there was no significant difference in biomass productivity at 25 and 30 °C (0.41 and 0.42 g·l-1·d-1, respectively. The highest fatty acid content (104.1 mg·g-1 CDW was recorded at low temperature (15 °C and decreased with increasing temperature. As a result of high biomass production, fatty acids productivity showed the highest values (41.27 and 42.10 mg·l-1·d-1 at 25 and 30 °C, respectively. The proportion of saturated and mono-unsaturated fatty acids increased from 13.72 to 23.79% and from 11.13 to 33.10% of total fatty acids when the incubation temperature was raised from 15 to 40 °C, respectively. The increase of temperature from 15 to 40 °C decreased the poly-unsaturated fatty acids from 75.15% to 43.10% of total fatty acids, respectively. Conclusions. The present study concluded that incubation temperature was a critical parameter for quantitative and qualitative fatty acid compositions of S. acutus. In addition, the type and proportion of individual fatty acids, which interfere with biodiesel quality, can be modified using different incubation temperatures in order to meet the biodiesel international standards.

  4. The Radiative Effects of Martian Water Ice Clouds on the Local Atmospheric Temperature Profile

    Science.gov (United States)

    Colaprete, Anthony; Toon, Owen B.

    2000-01-01

    Mars Pathfinder made numerous discoveries, one of which was a deep temperature inversion that extended from about 15 km down to 8 km above the surface. It has been suggested by Haberle et al. (1999. J. Geophys. Res. 104, 8957-8974.) that radiative cooling by a water ice cloud may generate such an inversion. Clouds can strongly affect the local air temperature due to their ability to radiate efficiently in the infrared and due to the low air mass of the martian atmosphere, which allows the temperature to change during the relatively short lifetime of a cloud. We utilize a time-dependent microphysical aerosol model coupled to a radiative--convective model to explore the effects water ice clouds have on the local martian temperature profile. We constrain the dust and water vapor abundance using data from the Viking Missions and Mars Pathfinder. Water t ice clouds with visible optical depths of r > 0.1 form readily in these simulations. These clouds alter the local air temperature directly, through infrared cooling, and indirectly, by redistributing atmospheric dust. With this model we are able to reproduce the temperature inversions observed by Mars Pathfinder and Mars Global t Surveyor 2000 Academic Press

  5. Base profile design for high-performance operation of bipolar transistors at liquid-nitrogen temperature

    International Nuclear Information System (INIS)

    Stork, J.M.C.; Harame, D.L.; Meyerson, B.S.; Nguyen, T.N.

    1989-01-01

    The base profile requirements of Si bipolar junction transistors (BJT's) high-performance operation at liquid-nitrogen temperature are examined. Measurements of thin epitaxial-base polysilicon-emitter n-p-n transistors with increasing base doping show the effects of bandgap narrowing, mobility changes, and carrier freezeout. At room temperature the collector current at low injection is proportional to the integrated base charge, independent of the impurity distribution. At temperatures below 150 Κ, however, minority injection is dominated by the peak base doping because of the greater effectiveness of bandgap narrowing. When the peak doping in the base approaches 10 19 cm -3 , the bandgap difference between emitter and base is sufficiently small that the current gain no longer monotonically decreases with lower temperature but instead shows a maximum as low as 180 Κ. The device design window appears limited at the low-current end by increased base-emitter leakage due to tunneling and by resistance control at the high-current end. Using the measured dc characteristics, circuit delay calculations are made to estimate the performance of an ECL ring oscillator at room and liquid-nitrogen temperatures. It is shown that if the base doping can be raised to 10 19 cm -3 while keeping the base thickness constant, the minimum delay at liquid nitrogen can approach the delay of optimized devices at room temperature

  6. Azimuthal velocity profiles in Rayleigh-stable Taylor–Couette flow and implied axial angular momentum transport

    NARCIS (Netherlands)

    Nordsiek, F.; Huisman, Sander Gerard; van der Veen, Roeland; Sun, Chao; Lohse, Detlef; Lathrop, D.P.

    2015-01-01

    We present azimuthal velocity profiles measured in a Taylor–Couette apparatus, which has been used as a model of stellar and planetary accretion disks. The apparatus has a cylinder radius ratio of ${\\it\\eta}=0.716$η=0.716, an aspect ratio of ${\\it\\Gamma}=11.74$Γ=11.74, and the plates closing the

  7. Profiles of Steroid Hormones in Canine X-Linked Muscular Dystrophy via Stable Isotope Dilution LC-MS/MS.

    Science.gov (United States)

    Martins-Júnior, Helio A; Simas, Rosineide C; Brolio, Marina P; Ferreira, Christina R; Perecin, Felipe; Nogueira, Guilherme de P; Miglino, Maria A; Martins, Daniele S; Eberlin, Marcos N; Ambrósio, Carlos E

    2015-01-01

    Golden retriever muscular dystrophy (GRMD) provides the best animal model for characterizing the disease progress of the human disorder, Duchenne muscular dystrophy (DMD). The purpose of this study was to determine steroid hormone concentration profiles in healthy golden retriever dogs (control group - CtGR) versus GRMD-gene carrier (CaGR) and affected female dogs (AfCR). Therefore, a sensitive and specific analytical method was developed and validated to determine the estradiol, progesterone, cortisol, and testosterone levels in the canine serum by isotope dilution liquid chromatography coupled with tandem mass spectrometry (LC-MS/MS). To more accurately understand the dynamic nature of the serum steroid profile, the fluctuating levels of these four steroid hormones over the estrous cycle were compared across the three experimental groups using a multivariate statistical analysis. The concentration profiles of estradiol, cortisol, progesterone, and testosterone revealed a characteristic pattern for each studied group at each specific estrous phase. Additionally, several important changes in the serum concentrations of cortisol and estradiol in the CaGR and AfCR groups seem to be correlated with the status and progression of the muscular dystrophy. A comprehensive and quantitative monitoring of steroid profiles throughout the estrous cycle of normal and GRMD dogs were achieved. Significant differences in these profiles were observed between GRMD and healthy animals, most notably for estradiol. These findings contribute to a better understanding of both dog reproduction and the muscular dystrophy pathology. Our data open new venues for hormonal behavior studies in dystrophinopathies and that may affect the quality of life of DMD patients.

  8. Profiles of Steroid Hormones in Canine X-Linked Muscular Dystrophy via Stable Isotope Dilution LC-MS/MS.

    Directory of Open Access Journals (Sweden)

    Helio A Martins-Júnior

    Full Text Available Golden retriever muscular dystrophy (GRMD provides the best animal model for characterizing the disease progress of the human disorder, Duchenne muscular dystrophy (DMD. The purpose of this study was to determine steroid hormone concentration profiles in healthy golden retriever dogs (control group - CtGR versus GRMD-gene carrier (CaGR and affected female dogs (AfCR. Therefore, a sensitive and specific analytical method was developed and validated to determine the estradiol, progesterone, cortisol, and testosterone levels in the canine serum by isotope dilution liquid chromatography coupled with tandem mass spectrometry (LC-MS/MS. To more accurately understand the dynamic nature of the serum steroid profile, the fluctuating levels of these four steroid hormones over the estrous cycle were compared across the three experimental groups using a multivariate statistical analysis. The concentration profiles of estradiol, cortisol, progesterone, and testosterone revealed a characteristic pattern for each studied group at each specific estrous phase. Additionally, several important changes in the serum concentrations of cortisol and estradiol in the CaGR and AfCR groups seem to be correlated with the status and progression of the muscular dystrophy. A comprehensive and quantitative monitoring of steroid profiles throughout the estrous cycle of normal and GRMD dogs were achieved. Significant differences in these profiles were observed between GRMD and healthy animals, most notably for estradiol. These findings contribute to a better understanding of both dog reproduction and the muscular dystrophy pathology. Our data open new venues for hormonal behavior studies in dystrophinopathies and that may affect the quality of life of DMD patients.

  9. Generalized saddle point condition for ignition in a tokamak reactor with temperature and density profiles

    International Nuclear Information System (INIS)

    Mitari, O.; Hirose, A.; Skarsgard, H.M.

    1989-01-01

    In this paper, the concept of a generalized ignition contour map, is extended to the realistic case of a plasma with temperature and density profiles in order to study access to ignition in a tokamak reactor. The generalized saddle point is found to lie between the Lawson and ignition conditions. If the height of the operation path with Goldston L-mode scaling is higher than the generalized saddle point, a reactor can reach ignition with this scaling for the case with no confinement degradation effect due to alpha-particle heating. In this sense, the saddle point given in a general form is a new criterion for reaching ignition. Peaking the profiles for the plasma temperature and density can lower the height of the generalized saddle point and help a reactor to reach ignition. With this in mind, the authors can judge whether next-generation tokamaks, such as Compact Ignition Tokamak, Tokamak Ignition/Burn Experimental Reactor, Next European Torus, Fusion Experimental Reactor, International Tokamak Reactor, and AC Tokamak Reactor, can reach ignition with realistic profile parameters and an L-mode scaling law

  10. Experiments on electron temperature profile resilience in FTU tokamak with continuous and modulated ECRH

    International Nuclear Information System (INIS)

    Cirant, S.

    2002-01-01

    Experiments performed on FTU tokamak, aiming at validation of physics-based transport models of the electron temperature profile resilience, are presented. ECRH is used to probe transport features, both in steady-state and in response to perturbations, while ECCD and LHCD are used for current density profile shaping. Observed confinement behaviour shows agreement with a critical temperature gradient length modelling. Central, low gradient plasma is characterized by low stiffness and low electron thermal diffusivity. Strong stiffness and high conduction are found in the confinement region. Resilience is experimentally characterized by an index of the resistance of the profile to adapt its shape to localized ECRH, while the diffusivity and its low-high transition are measured both by power balance and heat pulse propagation analysis. A particular attention is given to the investigation of the transition layer between low-high diffusivity and low-high stiffness regions. A dependence of LTc on magnetic shear, similar to what found in Tore Supra, and consistent with ETG based anomalous transport, is found. (author)

  11. CosmoTransitions: Computing cosmological phase transition temperatures and bubble profiles with multiple fields

    Science.gov (United States)

    Wainwright, Carroll L.

    2012-09-01

    I present a numerical package (CosmoTransitions) for analyzing finite-temperature cosmological phase transitions driven by single or multiple scalar fields. The package analyzes the different vacua of a theory to determine their critical temperatures (where the vacuum energy levels are degenerate), their supercooling temperatures, and the bubble wall profiles which separate the phases and describe their tunneling dynamics. I introduce a new method of path deformation to find the profiles of both thin- and thick-walled bubbles. CosmoTransitions is freely available for public use.Program summaryProgram Title: CosmoTransitionsCatalogue identifier: AEML_v1_0Program summary URL: http://cpc.cs.qub.ac.uk/summaries/AEML_v1_0.htmlProgram obtainable from: CPC Program Library, Queen's University, Belfast, N. IrelandLicensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.htmlNo. of lines in distributed program, including test data, etc.: 8775No. of bytes in distributed program, including test data, etc.: 621096Distribution format: tar.gzProgramming language: Python.Computer: Developed on a 2009 MacBook Pro. No computer-specific optimization was performed.Operating system: Designed and tested on Mac OS X 10.6.8. Compatible with any OS with Python installed.RAM: Approximately 50 MB, mostly for loading plotting packages.Classification: 1.9, 11.1.External routines: SciPy, NumPy, matplotLibNature of problem: I describe a program to analyze early-Universe finite-temperature phase transitions with multiple scalar fields. The goal is to analyze the phase structure of an input theory, determine the amount of supercooling at each phase transition, and find the bubble-wall profiles of the nucleated bubbles that drive the transitions.Solution method: To find the bubble-wall profile, the program assumes that tunneling happens along a fixed path in field space. This reduces the equations of motion to one dimension, which can then be solved using the overshoot

  12. Comparison of Temperature Measurements in the Middle Atmosphere by Satellite with Profiles Obtained by Meteorological Rockets

    Science.gov (United States)

    Goldberg, Richard A.; Schmidlin, Francis J.; Feofilov, Artem; Bedrick, M.; Rose, R. Lynn

    2012-01-01

    Measurements using the inflatable falling sphere technique have occasionally been used to obtain temperature results from density data and thereby provide comparison with temperature profiles obtained by satellite sounders in the mesosphere and stratosphere. To insure density measurements within narrow time frames and close in space, the inflatable falling sphere is launched within seconds of the nearly overhead satellite pass. Sphere measurements can be used to validate remotely measured temperatures but also have the advantage of measuring small-scale atmospheric features. Even so, with the dearth of remaining falling spheres available (the manufacture of these systems has been discontinued), it may be time to consider whether the remote measurements are mature enough to stand alone. Three field studies are considered, one in 2003 from Northern Sweden, and two in 2010 from the vicinity of Kwajalein Atoll in the South Pacific and from Barking Sands, Hawaii. All three sites are used to compare temperature retrievals between satellite and in situ falling spheres. The major satellite instruments employed are SABER, MLS, and AIRS. The comparisons indicate that remotely measured temperatures mimic the sphere temperature measurements quite well. The data also confirm that satellite retrievals, while not always at the exact location required for detailed studies in space and time, compare sufficiently well to be highly useful. Although the falling sphere will provide a measurement at a specific location and time, satellites only pass a given location daily or less frequently. This report reveals that averaged satellite measurements can provide temperatures and densities comparable to those obtained from the falling sphere, thereby providing a reliable measure of global temperature

  13. The New Weather Radar for America's Space Program in Florida: A Temperature Profile Adaptive Scan Strategy

    Science.gov (United States)

    Carey, L. D.; Petersen, W. A.; Deierling, W.; Roeder, W. P.

    2009-01-01

    A new weather radar is being acquired for use in support of America s space program at Cape Canaveral Air Force Station, NASA Kennedy Space Center, and Patrick AFB on the east coast of central Florida. This new radar replaces the modified WSR-74C at Patrick AFB that has been in use since 1984. The new radar is a Radtec TDR 43-250, which has Doppler and dual polarization capability. A new fixed scan strategy was designed to best support the space program. The fixed scan strategy represents a complex compromise between many competing factors and relies on climatological heights of various temperatures that are important for improved lightning forecasting and evaluation of Lightning Launch Commit Criteria (LCC), which are the weather rules to avoid lightning strikes to in-flight rockets. The 0 C to -20 C layer is vital since most generation of electric charge occurs within it and so it is critical in evaluating Lightning LCC and in forecasting lightning. These are two of the most important duties of 45 WS. While the fixed scan strategy that covers most of the climatological variation of the 0 C to -20 C levels with high resolution ensures that these critical temperatures are well covered most of the time, it also means that on any particular day the radar is spending precious time scanning at angles covering less important heights. The goal of this project is to develop a user-friendly, Interactive Data Language (IDL) computer program that will automatically generate optimized radar scan strategies that adapt to user input of the temperature profile and other important parameters. By using only the required scan angles output by the temperature profile adaptive scan strategy program, faster update times for volume scans and/or collection of more samples per gate for better data quality is possible, while maintaining high resolution at the critical temperature levels. The temperature profile adaptive technique will also take into account earth curvature and refraction

  14. Robust/optimal temperature profile control of a high-speed aerospace vehicle using neural networks.

    Science.gov (United States)

    Yadav, Vivek; Padhi, Radhakant; Balakrishnan, S N

    2007-07-01

    An approximate dynamic programming (ADP)-based suboptimal neurocontroller to obtain desired temperature for a high-speed aerospace vehicle is synthesized in this paper. A 1-D distributed parameter model of a fin is developed from basic thermal physics principles. "Snapshot" solutions of the dynamics are generated with a simple dynamic inversion-based feedback controller. Empirical basis functions are designed using the "proper orthogonal decomposition" (POD) technique and the snapshot solutions. A low-order nonlinear lumped parameter system to characterize the infinite dimensional system is obtained by carrying out a Galerkin projection. An ADP-based neurocontroller with a dual heuristic programming (DHP) formulation is obtained with a single-network-adaptive-critic (SNAC) controller for this approximate nonlinear model. Actual control in the original domain is calculated with the same POD basis functions through a reverse mapping. Further contribution of this paper includes development of an online robust neurocontroller to account for unmodeled dynamics and parametric uncertainties inherent in such a complex dynamic system. A neural network (NN) weight update rule that guarantees boundedness of the weights and relaxes the need for persistence of excitation (PE) condition is presented. Simulation studies show that in a fairly extensive but compact domain, any desired temperature profile can be achieved starting from any initial temperature profile. Therefore, the ADP and NN-based controllers appear to have the potential to become controller synthesis tools for nonlinear distributed parameter systems.

  15. Asymptotic solutions of glass temperature profiles during steady optical fibre drawing

    KAUST Repository

    Taroni, M.

    2013-03-12

    In this paper we derive realistic simplified models for the high-speed drawing of glass optical fibres via the downdraw method that capture the fluid dynamics and heat transport in the fibre via conduction, convection and radiative heating. We exploit the small aspect ratio of the fibre and the relative orders of magnitude of the dimensionless parameters that characterize the heat transfer to reduce the problem to one- or two-dimensional systems via asymptotic analysis. The resulting equations may be readily solved numerically and in many cases admit exact analytic solutions. The systematic asymptotic breakdown presented is used to elucidate the relative importance of furnace temperature profile, convection, surface radiation and conduction in each portion of the furnace and the role of each in controlling the glass temperature. The models derived predict many of the qualitative features observed in real industrial processes, such as the glass temperature profile within the furnace and the sharp transition in fibre thickness. The models thus offer a desirable route to quick scenario testing, providing valuable practical information about the dependencies of the solution on the parameters and the dominant heat-transport mechanism. © 2013 Springer Science+Business Media Dordrecht.

  16. Iterative noise removal from temperature and density profiles in the TJ-II Thomson scattering

    International Nuclear Information System (INIS)

    Farias, G.; Dormido-Canto, S.; Vega, J.; Santos, M.; Pastor, I.; Fingerhuth, S.; Ascencio, J.

    2014-01-01

    TJ-II Thomson Scattering diagnostic provides temperature and density profiles of plasma. The CCD camera acquires images that are corrupted with some kind of noise called stray-light. This noise degrades both image contrast and measurement accuracy, which could produce unreliable profiles of the diagnostic. So far, several approaches have been applied in order to decrease the noise in the TJ-II Thomson scattering images. Since the presence of the noise is not global but located in some particular regions of the image, advanced processing techniques are needed. However such methods require of manual fine-tuning of parameters to reach a good performance. In this contribution, an iterative image processing approach is applied in order to reduce the stray light effects in the images of the TJ-II Thomson scattering diagnostic. The proposed solution describes how the noise can be iteratively reduced in the images when a key parameter is automatically adjusted during the iterative process

  17. Iterative noise removal from temperature and density profiles in the TJ-II Thomson scattering

    Energy Technology Data Exchange (ETDEWEB)

    Farias, G., E-mail: gonzalo.farias@ucv.cl [Pontificia Universidad Católica de Valparaíso, Av. Brasil 2147, Valparaíso (Chile); Dormido-Canto, S., E-mail: sebas@dia.uned.es [Departamento de Informática y Automática, UNED, 28040 Madrid (Spain); Vega, J., E-mail: jesus.vega@ciemat.es [Asociación EURATOM/CIEMAT para Fusión, Avd. Complutense 22, 28040 Madrid (Spain); Santos, M., E-mail: msantos@ucm.es [Departamento de Arquitectura de Computadores y Automática, Universidad Complutense de Madrid, 28040 Madrid (Spain); Pastor, I., E-mail: ignacio.pastor@ciemat.es [Asociación EURATOM/CIEMAT para Fusión, Avd. Complutense 22, 28040 Madrid (Spain); Fingerhuth, S., E-mail: sebastian.fingerhuth@ucv.cl [Pontificia Universidad Católica de Valparaíso, Av. Brasil 2147, Valparaíso (Chile); Ascencio, J., E-mail: j_ascencio21@hotmail.com [Pontificia Universidad Católica de Valparaíso, Av. Brasil 2147, Valparaíso (Chile)

    2014-05-15

    TJ-II Thomson Scattering diagnostic provides temperature and density profiles of plasma. The CCD camera acquires images that are corrupted with some kind of noise called stray-light. This noise degrades both image contrast and measurement accuracy, which could produce unreliable profiles of the diagnostic. So far, several approaches have been applied in order to decrease the noise in the TJ-II Thomson scattering images. Since the presence of the noise is not global but located in some particular regions of the image, advanced processing techniques are needed. However such methods require of manual fine-tuning of parameters to reach a good performance. In this contribution, an iterative image processing approach is applied in order to reduce the stray light effects in the images of the TJ-II Thomson scattering diagnostic. The proposed solution describes how the noise can be iteratively reduced in the images when a key parameter is automatically adjusted during the iterative process.

  18. SIMULATION OF A MATHEMATICAL MODEL FOR THE TEMPERATURE PROFILE IN A SILO BAG FOR BEAN

    Directory of Open Access Journals (Sweden)

    M. R. Hauth

    2015-02-01

    Full Text Available The problems encountered with storage of agricultural products has warranted studies related to finding alternative methods of grain storage, thereby avoiding unnecessary losses. Stored grain deteriorates quickly at high temperatures. The moisture content of the grain influences the respiratory process; therefore, when at the recommended humidity of between 11 and 13%, this rate remains low, it prolongs maintenance of the product quality. The silo bag being airtight enables the grain mass to consume the entire internal O2 purse within it, and in that low or absent oxygen environment the grain mass saturates the CO2 atmosphere, inhibiting the multiplication of insects and fungi, thus providing a controlled environment. This study aims at simulating, using Computational Fluid Dynamics (CFD, the time it would take for the entire grain mass contained in a silo bag to reach thermal equilibrium with the environment and analyzes the feasibility of the technique employed here. The simulations were performed based on the data of the average air temperature in the region at each harvest time and the average storage temperature of the bean mass (60°C. The results obtained from the simulations reveal that after one month of silo storage the entire bag remains in thermal stabilization, and four months later when it hits the entire mass, all the beans are in thermal equilibrium. Therefore, maintaining stable temperature and humidity within the recommended silo bag preserves the grain quality well.

  19. The Genome-Wide DNA Methylation Profile of Peripheral Blood Is Not Systematically Changed by Short-Time Storage at Room Temperature

    Directory of Open Access Journals (Sweden)

    Nicklas Heine Staunstrup

    2017-12-01

    Full Text Available Background: Epigenetic epidemiology has proven an important research discipline in the delineation of diseases of complex etiology. The approach, in such studies, is often to use bio-banked clinical material, however, many such samples were collected for purposes other than epigenetic studies and, thus, potentially not processed and stored appropriately. The Danish National Birth Cohort (DNBC includes more than 100,000 peripheral and umbilical cord blood samples shipped from maternity wards by ordinary mail in EDTA tubes. While this and other similar cohorts hold great promises for DNA methylation studies the potential systematic changes prompted by storage at ambient temperatures have never been assessed on a genome-wide level. Methods and Results: In this study, matched EDTA whole blood samples were stored up to three days at room temperature prior to DNA extraction and methylated DNA immunoprecipitation coupled with deep sequencing (MeDIP-seq. We established that the quality of the MeDIP-seq libraries was high and comparable across samples; and that the methylation profiles did not change systematically during the short-time storage at room temperature. Conclusion: The global DNA methylation profile is stable in whole blood samples stored for up to three days at room temperature in EDTA tubes making genome-wide methylation studies on such material feasible.

  20. On the determination of biases in satellite-derived temperature profiles

    Science.gov (United States)

    Bhatt, Praful P.; Remsberg, Ellis E.; Schmidlin, Francis J.; Gordley, Larry L.; Burton, John C.

    1994-01-01

    Comparisons are presented between Nimbus 7 LIMS (Limb Infrared Monitor of the Stratosphere) mapped temperatures and both Datasonde and sphere in situ rocketsonde temperature measurements. With this approach up to 666 LIMS/Datasonde pairs were obtained for various pressure levels to look for small biases in LIMS temperatures as a function of altitude, latitude and season. Between 10-1 hPa LIMS and Datasonde agree everywhere to better than +/- 2 K with the exception of a warm bias of about 3 K at 2 hPa at high latitudes. However, LIMS is colder than the Datasonde by about 4 K at 0.4 hPa and by about 8-10 K at 0.1 hPa. When compared with the more accurate sphere temperatures the bias at 0.1 hPa is reduced by nearly one-half. These results indicate that the LIMS zonal mean constituent profiles are nearly free of temperature bias, except perhaps at 0.1 hPa.

  1. Modeling the microbial growth and temperature profile in a fixed-bed bioreactor.

    Science.gov (United States)

    da Silveira, Christian L; Mazutti, Marcio A; Salau, Nina P G

    2014-10-01

    Aiming to scale up and apply control and optimization strategies, currently is required the development of accurate plant models to forecast the process nonlinear dynamics. In this work, a mathematical model to predict the growth of the Kluyveromyces marxianus and temperature profile in a fixed-bed bioreactor for solid-state fermentation using sugarcane bagasse as substrate was built up. A parameter estimation technique was performed to fit the mathematical model to the experimental data. The estimated parameters and the model fitness were evaluated with statistical analyses. The results have shown the estimated parameters significance, with 95 % confidence intervals, and the good quality of process model to reproduce the experimental data.

  2. 1DTempPro: analyzing temperature profiles for groundwater/surface-water exchange

    Science.gov (United States)

    Voytek, Emily B.; Drenkelfuss, Anja; Day-Lewis, Frederick D.; Healy, Richard; Lane, John W.; Werkema, Dale D.

    2014-01-01

    A new computer program, 1DTempPro, is presented for the analysis of vertical one-dimensional (1D) temperature profiles under saturated flow conditions. 1DTempPro is a graphical user interface to the U.S. Geological Survey code Variably Saturated 2-Dimensional Heat Transport (VS2DH), which numerically solves the flow and heat-transport equations. Pre- and postprocessor features allow the user to calibrate VS2DH models to estimate vertical groundwater/surface-water exchange and also hydraulic conductivity for cases where hydraulic head is known.

  3. Pure rotational Raman lidar for the measurement of vertical profiles of temperature in the lower atmosphere

    Science.gov (United States)

    Satyanarayana, M.; Radhakrishnan, S. R.; Presennakumar, B.; Murty, V. S.; Bindhu, R.

    2006-12-01

    The design and development of the new Raman lidar of the Space Physics Laboratory, Vikram Sarabhai Space Centre is presented here. This station is located at 8 degrees 33 minutes N, 77 degrees E in India. This lidar can monitor atmospheric temperature (using Pure Rotational Raman Spectrum), aerosol extinction coefficient, water vapor profile and clouds. Advantages of Pure Rotational Raman method over Vibrational Raman method are presented with the result obtained using Vibrational Raman lidar. Optical layout of the lidar system, PRRS method and aerosol extinction measurements are described briefly.

  4. Oceanographic profile temperature and salinity measurements collected using bottle from the LITKE in the Arctic in 1948 (NODC Accession 0001088)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature, salinity and other profile data digitized at NODC on 05/02/03, received by Igor Smolyar from Matishov, G., A. Zuyev, V. Golubev, N. Adrov, S. Timofeev,...

  5. Oceanographic profile temperature, salinity and other measurements collected using bottle in the Arctic in 1934 (NODC Accession 0001244)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile and meteorological data were collected using bottle casts in the Barents Sea, Kara Sea, Laptev Sea, White Sea, and Arctic Ocean. Data were...

  6. Temperature profile data from XBT casts by SEAS program participating vessels, November 2001 - January 2002 (NODC Accession 0000661)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profiles were collected from XBT casts from the OLEANDER and other platforms from a world-wide distribution from 22 November 2001 to 23 January 2002....

  7. Real-time measurements of temperature, pressure and moisture profiles in High-Performance Concrete exposed to high temperatures during neutron radiography imaging

    Energy Technology Data Exchange (ETDEWEB)

    Toropovs, N., E-mail: nikolajs.toropovs@rtu.lv [Empa, Swiss Federal Laboratories for Materials Science and Technology, Dübendorf (Switzerland); Riga Technical University, Institute of Materials and Structures, Riga (Latvia); Lo Monte, F. [Politecnico di Milano, Department of Civil and Environmental Engineering, Milan (Italy); Wyrzykowski, M. [Empa, Swiss Federal Laboratories for Materials Science and Technology, Dübendorf (Switzerland); Lodz University of Technology, Department of Building Physics and Building Materials, Lodz (Poland); Weber, B. [Empa, Swiss Federal Laboratories for Materials Science and Technology, Dübendorf (Switzerland); Sahmenko, G. [Riga Technical University, Institute of Materials and Structures, Riga (Latvia); Vontobel, P. [Paul Scherrer Institute, Laboratory for Neutron Scattering and Imaging, Villigen (Switzerland); Felicetti, R. [Politecnico di Milano, Department of Civil and Environmental Engineering, Milan (Italy); Lura, P. [Empa, Swiss Federal Laboratories for Materials Science and Technology, Dübendorf (Switzerland); ETH Zürich, Institute for Building Materials (IfB), Zürich (Switzerland)

    2015-02-15

    High-Performance Concrete (HPC) is particularly prone to explosive spalling when exposed to high temperature. Although the exact causes that lead to spalling are still being debated, moisture transport during heating plays an important role in all proposed mechanisms. In this study, slabs made of high-performance, low water-to-binder ratio mortars with addition of superabsorbent polymers (SAP) and polypropylene fibers (PP) were heated from one side on a temperature-controlled plate up to 550 °C. A combination of measurements was performed simultaneously on the same sample: moisture profiles via neutron radiography, temperature profiles with embedded thermocouples and pore pressure evolution with embedded pressure sensors. Spalling occurred in the sample with SAP, where sharp profiles of moisture and temperature were observed. No spalling occurred when PP-fibers were introduced in addition to SAP. The experimental procedure described here is essential for developing and verifying numerical models and studying measures against fire spalling risk in HPC.

  8. Logarithmic Mean Temperature Profiles and Their Connection to Plume Emissions in Turbulent Rayleigh-Bénard Convection

    NARCIS (Netherlands)

    van der Poel, Erwin; Ostilla Monico, Rodolfo; Verzicco, Roberto; Grossmann, S.; Lohse, Detlef

    2015-01-01

    Two-dimensional simulations of Rayleigh-Bénard convection at Ra ¼ 5 × 1010 show that vertical logarithmic mean temperature profiles can be observed in regions of the boundary layer where thermal plumes are emitted. The profile is logarithmic only in these regions and not in the rest of the boundary

  9. Regional surface fluxes from satellite-derived surface temperatures (AVHRR) and radiosonde profiles

    Science.gov (United States)

    Brutsaert, Wilfried; Sugita, Michiaki

    1992-01-01

    Radiometric surface temperatures, derived from measurements by the AVHRR instrument aboard the NOAA-9 and the NOAA-11 polar orbiting satellites, were used in combination with wind velocity and temperature profiles measured by radiosondes, to calculate surface fluxes of sensible heat. The measurements were made during FIFE, the First ISLSCP (International Satellite Land Surface Climatology Project) Field Experiment, in a hilly tall grass prairie area of northeastern Kansas. The method of calculation was based on turbulent similarity formulations for the atmospheric boundary layer. Good agreement (r = 0.7) was obtained with reference values of sensible heat flux, taken as arithmetric means of measurements with the Bowen ratio method at six ground stations. The values of evaporation (latent heat fluxes), derived from these sensible heat fluxes by means of the energy budget, were also in good agreement (r = 0.94) with the corresponding reference values from the ground stations.

  10. Diagnosis of Coronary Heart Diseases Using Gene Expression Profiling; Stable Coronary Artery Disease, Cardiac Ischemia with and without Myocardial Necrosis.

    Directory of Open Access Journals (Sweden)

    Nabila Kazmi

    Full Text Available Cardiovascular disease (including coronary artery disease and myocardial infarction is one of the leading causes of death in Europe, and is influenced by both environmental and genetic factors. With the recent advances in genomic tools and technologies there is potential to predict and diagnose heart disease using molecular data from analysis of blood cells. We analyzed gene expression data from blood samples taken from normal people (n = 21, non-significant coronary artery disease (n = 93, patients with unstable angina (n = 16, stable coronary artery disease (n = 14 and myocardial infarction (MI; n = 207. We used a feature selection approach to identify a set of gene expression variables which successfully differentiate different cardiovascular diseases. The initial features were discovered by fitting a linear model for each probe set across all arrays of normal individuals and patients with myocardial infarction. Three different feature optimisation algorithms were devised which identified two discriminating sets of genes, one using MI and normal controls (total genes = 6 and another one using MI and unstable angina patients (total genes = 7. In all our classification approaches we used a non-parametric k-nearest neighbour (KNN classification method (k = 3. The results proved the diagnostic robustness of the final feature sets in discriminating patients with myocardial infarction from healthy controls. Interestingly it also showed efficacy in discriminating myocardial infarction patients from patients with clinical symptoms of cardiac ischemia but no myocardial necrosis or stable coronary artery disease, despite the influence of batch effects and different microarray gene chips and platforms.

  11. Temperature and Relative Humidity Vertical Profiles within Planetary Boundary Layer in Winter Urban Airshed

    Science.gov (United States)

    Bendl, Jan; Hovorka, Jan

    2017-12-01

    The planetary boundary layer is a dynamic system with turbulent flow where horizontal and vertical air mixing depends mainly on the weather conditions and geomorphology. Normally, air temperature from the Earth surface decreases with height but inversion situation may occur, mainly during winter. Pollutant dispersion is poor during inversions so air pollutant concentration can quickly rise, especially in urban closed valleys. Air pollution was evaluated by WHO as a human carcinogen (mostly by polycyclic aromatic hydrocarbons) and health effects are obvious. Knowledge about inversion layer height is important for estimation of the pollution impact and it can give us also information about the air pollution sources. Temperature and relative humidity vertical profiles complement ground measurements. Ground measurements were conducted to characterize comprehensively urban airshed in Svermov, residential district of the city of Kladno, about 30 km NW of Prague, from the 2nd Feb. to the 3rd of March 2016. The Svermov is an air pollution hot-spot for long time benzo[a]pyrene (B[a]P) limit exceedances, reaching the highest B[a]P annual concentration in Bohemia - west part of the Czech Republic. Since the Svermov sits in a shallow valley, frequent vertical temperature inversion in winter and low emission heights of pollution sources prevent pollutant dispersal off the valley. Such orography is common to numerous small settlements in the Czech Republic. Ground measurements at the sports field in the Svermov were complemented by temperature and humidity vertical profiles acquired by a Vaisala radiosonde positioned at tethered He-filled balloon. Total number of 53 series of vertical profiles up to the height of 300 m was conducted. Meteorology parameters were acquired with 4 Hz frequency. The measurements confirmed frequent early-morning and night formation of temperature inversion within boundary layer up to the height of 50 m. This rather shallow inversion had significant

  12. Strong anisotropy in the low temperature Compton profiles of electron momentum distribution in α-Ga metal

    International Nuclear Information System (INIS)

    Panda, B.P.; Mohapatra, N.C.

    2002-01-01

    Compton profiles of momentum distribution of conduction electrons in the orthorhombic phase of α-Ga metal at low temperature are calculated in the band model for the three crystallographic directions (100), (010), and (001). Unlike the results at room temperature, previously reported by Lengeler, Lasser and Mair, the present results show strong anisotropy in the Compton profiles with the momentum distribution along (001) direction being substantially different from the other two directions. While experimental data on Compton profiles at low temperatures are not available for comparison with theory, the resistivity data in α-Ga at low temperature strongly support this anisotropic behaviour. Besides, the electronic heat capacity constant γ available from both experiment and present calculation suggests that conduction electron distribution at low temperature in the orthorhombic phase is markedly different from the free-electron-like-distribution at room temperature, thus lending additional support to anisotropic behaviour of Compton profiles. It would be nice to have Compton profiles data from experiment at low temperature for direct comparison with theory. It is hoped that the present work would stimulate enough interest in that direction. (author)

  13. On the meaning of peak temperature profiles in inverted metamorphic sequences

    Science.gov (United States)

    Duprat-Oualid, Sylvia; Yamato, Philippe

    2017-07-01

    Inverted metamorphic sequences (IMS) are common features of main thrust systems on Earth. They exhibit an upwards continuous increase in peak temperature conditions and thereby constitute evidence of the close relationship between the thermal field evolution and tectonic processes. Heat advection and shear heating are known to allow the formation of such metamorphic signatures. Heat diffusion also plays an important role in temperature distribution on both sides of the thrust. Other advection processes such as erosion or accretion may also cause a local peak temperature inversion. Each one of these processes therefore affects the thermal field around the thrust. However, despite the crucial importance of all these processes for the interpretation of the inverted peak temperature signatures, their respective influences have never been quantified and compared all together. To address this issue, we propose an innovative coupled approach. (i) We use two-dimensional numerical models that simulate various thrust systems, allowing for a wide diversity of setups. To illustrate this study, we focus on intracontinental thrust systems for which all processes listed are likely to play a key role in the thermal evolution. We perform a parametric study including kinematic settings (i.e. convergence, erosion and accretion), thermal properties, mechanical strength and heat sources. (ii) Dimensionless numbers based on parameters are used to quantify the relative contributions of each process to the thermal budget evolution. Hence, the three thermal processes (i.e. heat diffusion, heat advection and shear heating) are compared with each other via three dimensionless combinations of the Peclet and Brinkman numbers: RDif, RAdv and RPro, respectively. Erosion and accretion are compared separately, based on a fourth dimensionless number Rea. (iii) We analytically examine the inverted peak temperature recorded along profiles that are perpendicular to the thrust zone defined in our

  14. Saturn’s Helium Abundance from Cassini VIMS Stellar Occultations and CIRS Limb Temperature Profiles

    Science.gov (United States)

    Banfield, Don; Gierasch, Peter J.; Conrath, Barney J.; Achterberg, Richard K.; Nicholson, Phillip D.; Hedman, Matthew M.

    2014-11-01

    We have used Saturn stellar occultations as observed by Cassini VIMS, in concert with Saturn limb temperature profiles derived from Cassini CIRS data to determine the Helium abundance in Saturn’s atmosphere near a few mbars. This quantity is long sought, as indication of the internal evolution that Saturn has undergone. Additionally, previous attempts to determine this quantity have produced inconsistent results ranging from He/H2=0.03±0.02 using Voyager IRIS and RSS (Conrath et al., 1984) to He/H2=0.13±0.02 using only Voyager IRIS (Conrath & Gautier, 2000) with a similar result being found by Orton and Ingersoll (1980) using Pioneer IRR and RSS (He/H2=0.11±0.04). These discordant results motivate us to try yet another approach to yield this quantity, in this case using the Cassini VIMS stellar occultations to yield a profile of atmospheric density, and nearly co-located Cassini CIRS limb profiles to yield atmospheric temperature. Combining the two results then yields the mean molecular weight and thus the He/H2 mixing ratio. We reported preliminary values from an occultation from the 151st Cassini orbit at DPS in 2011 (He/H2=0.14±0.05), but have since identified errors in that analysis that have caused us to revisit the problem. Additionally, that occultation occurred near the large Saturn northern hemisphere storm, with significant longitudinal temperature gradients present. The longitudinal separation between the CIRS and VIMS footprints could have skewed the results. In this report, we will discuss our latest results with the algorithm errors corrected, and using data from an occultation of Betelgeuse on the 161st Cassini orbit. These data have the best S/N of all stellar occultations caught by Cassini VIMS to date, and the combination of the VIMS/CIRS data doesn’t suffer from problems due to proximity to the storm and its associated spatial gradients in temperature.

  15. Profiles of chloride and water stable isotope in porewater obtained from a 2000 m-deep borehole through the Mesozoic sedimentary series in the East of France

    International Nuclear Information System (INIS)

    Bensenouci, F.; Michelot, J.L.; Matray, J.M.; Savoye, S.

    2010-01-01

    Document available in extended abstract form only. A method to obtain information about fluid flow and solute transport in porous media with low hydraulic conductivity and low water content is based on the study of the natural tracer distribution in pore water. This approach was previously applied to the Callovo-Oxfordian argillites, studied by Andra at the Bure URL (East of France), using several natural tracer profiles ( 4 He, 2 H, 18 O, Cl - , 37 Cl). These profiles were interpreted as the result of a diffusive exchange between pore water in the aquitard and groundwater in the surrounding aquifers. However, at the Bure URL, and in contrast to other investigated argillaceous formations, the concentrations of tracers in lower aquifer groundwater may be higher than those in argillite pore water and increase with depth. The continuity of the profiles and the origin of pore water salinity remained questionable. This study aims at presenting and interpreting chloride and stable isotope profiles in pore water through more than 800 m of sediments, from the lower Oxfordian to the lower Hettangian. Drill-core samples were collected from the 2000 m-deep borehole (EST 433) drilled by Andra in the so-called 'Transposition Zone', located north to the Bure URL. In the framework of the TAPPS 2000 programme, twenty-five core samples were collected from the Oxfordian to the lower Hettangian during the drilling campaign, and in-situ conditioned. The chloride concentrations in pore water were firstly estimated by aqueous leaching, using a geochemical porosity two times smaller than the porosity measured by heating at 150 deg. C. After this estimation of pore water salinities, the radial diffusion and vapour exchange methods were applied to determine the stable isotope and anion concentrations in pore water. The deuterium contents of pore water derived from the vapour exchange experiments describe a classical bell-shape profile in the Callovo-Oxfordian argillites with an

  16. High-temperature synthesis of highly hydrothermal stable mesoporous silica and Fe-SiO2 using ionic liquid as a template

    International Nuclear Information System (INIS)

    Liu, Hong; Wang, Mengyang; Hu, Hongjiu; Liang, Yuguang; Wang, Yong; Cao, Weiran; Wang, Xiaohong

    2011-01-01

    Mesoporous silicas and Fe-SiO 2 with worm-like structures have been synthesized using a room temperature ionic liquid, 1-hexadecane-3-methylimidazolium bromide, as a template at a high aging temperature (150-190 o C) with the assistance of NaF. The hydrothermal stability of mesoporous silica was effectively improved by increasing the aging temperature and adding NaF to the synthesis gel. High hydrothermally stable mesoporous silica was obtained after being aged at 190 o C in the presence of NaF, which endured the hydrothermal treatment in boiling water at least for 10 d or steam treatment at 600 o C for 6 h. The ultra hydrothermal stability could be attributed to its high degree of polymerization of silicate. Furthermore, highly hydrothermal stable mesoporous Fe-SiO 2 has been synthesized, which still remained its mesostructure after being hydrothermally treated at 100 o C for 12 d or steam-treated at 600 o C for 6 h. -- Graphical abstract: Worm-like mesoporous silica and Fe-SiO 2 with high hydrothermal stability have been synthesized using ionic liquid 1-hexadecane-3-methylimidazolium bromide as a template under the assistance of NaF at high temperature. Display Omitted Research highlights: → Increasing aging temperature improved the hydrothermal stability of materials. →Addition of NaF enhanced the polymerization degree of silicates. → Mesoporous SiO 2 and Fe-SiO 2 obtained have remarkable hydrothermal stability.

  17. Numerical study on transverse asymmetry in the temperature profile of a regenerator in a pulse tube cooler

    DEFF Research Database (Denmark)

    Andersen, Stig Kildegård; Dietrich, M.; Carlsen, Henrik

    2007-01-01

    Transverse asymmetry in the temperature profile of the regenerator in a Stirling-type pulse tube cooler as observed in experiments was analysed in a numerical study. The asymmetry was reproduced using a one-dimensional model of the cooler where the regenerator was modelled using two identical...... mass flow rate on the pressure difference and temperature....

  18. The Measurement of Tropospheric Temperature Profiles using Rayleigh-Brillouin Scattering : Results from Laboratory and Atmospheric Studies

    NARCIS (Netherlands)

    Witschas, Benjamin; Reitebuch, Oliver; Lemmerz, Christian; Kableka, Pau Gomez; Kondratyev, Sergey; Gu, Z.; Ubachs, Wim

    2016-01-01

    In this letter, we suggest a new method for measuring tropospheric temperature profiles using Rayleigh-Brillouin (RB) scattering. We report on laboratory RB scattering measurements in air, demonstrating that temperature can be retrieved from RB spectra with an absolute accuracy of better than 2 K.

  19. temperature

    Directory of Open Access Journals (Sweden)

    G. Polt

    2015-10-01

    Full Text Available In-situ X-ray diffraction was applied to isotactic polypropylene with a high volume fraction of α-phase (α-iPP while it has been compressed at temperatures below and above its glass transition temperature Tg. The diffraction patterns were evaluated by the Multi-reflection X-ray Profile Analysis (MXPA method, revealing microstructural parameters such as the density of dislocations and the size of coherently scattering domains (CSD-size. A significant difference in the development of the dislocation density was found compared to compression at temperatures above Tg, pointing at a different plastic deformation mechanism at these temperatures. Based on the individual evolutions of the dislocation density and CSD-size observed as a function of compressive strain, suggestions for the deformation mechanisms occurring below and above Tg are made.

  20. Profiling primaquine metabolites in primary human hepatocytes using UHPLC-QTOF-MS with 13C stable isotope labeling.

    Science.gov (United States)

    Avula, Bharathi; Tekwani, Babu L; Chaurasiya, Narayan D; Nanayakkara, N P Dhammika; Wang, Yan-Hong; Khan, Shabana I; Adelli, Vijender R; Sahu, Rajnish; Elsohly, Mahmoud A; McChesney, James D; Khan, Ikhlas A; Walker, Larry A

    2013-02-01

    Therapeutic efficiency and hemolytic toxicity of primaquine (PQ), the only drug available for radical cure of relapsing vivax malaria are believed to be mediated by its metabolites. However, identification of these metabolites has remained a major challenge apparently due to low quantities and their reactive nature. Drug candidates labeled with stable isotopes afford convenient tools for tracking drug-derived metabolites in complex matrices by liquid chromatography-tandem mass spectrometry (LC-MS-MS) and filtering for masses with twin peaks attributable to the label. This study was undertaken to identify metabolites of PQ from an in vitro incubation of a 1:1 w/w mixture of (13)C(6)-PQ/PQ with primary human hepatocytes. Acquity ultra-performance LC (UHPLC) was integrated with QTOF-MS to combine the efficiency of separation with high sensitivity, selectivity of detection and accurate mass determination. UHPLC retention time, twin mass peaks with difference of 6 (originating from (13)C(6)-PQ/PQ), and MS-MS fragmentation pattern were used for phenotyping. Besides carboxy-PQ (cPQ), formed by oxidative deamination of PQ to an aldehyde and subsequent oxidation, several other metabolites were identified: including PQ alcohol, predictably generated by oxidative deamination of PQ to an aldehyde and subsequent reduction, its acetate and the alcohol's glucuronide conjugate. Trace amounts of quinone-imine metabolites of PQ and cPQ were also detected which may be generated by hydroxylation of the PQ/cPQ quinoline ring at the 5-position and subsequent oxidation. These findings shed additional light on the human hepatic metabolism of PQ, and the method can be applied for identification of reactive PQ metabolites generated in vivo in preclinical and clinical studies. Copyright © 2013 John Wiley & Sons, Ltd.

  1. Organochlorine contaminant and stable isotope profiles in Arctic fox (Alopex lagopus) from the Alaskan and Canadian Arctic

    International Nuclear Information System (INIS)

    Hoekstra, P.F.; Braune, B.M.; O'Hara, T.M.; Elkin, B.; Solomon, K.R.; Muir, D.C.G.

    2003-01-01

    PCBs in Arctic fox are lower than reported in other Arctic populations and unlikely to cause significant impairment of reproductive success. - Arctic fox (Alopex lagopus) is a circumpolar species distributed across northern Canada and Alaska. Arctic fox muscle and liver were collected at Barrow, AK, USA (n=18), Holman, NT, Canada (n=20), and Arviat, NU, Canada (n=20) to elucidate the feeding ecology of this species and relate these findings to body residue patterns of organochlorine contaminants (OCs). Stable carbon (δ 13 C) and nitrogen (δ 15 N) isotope analyses of Arctic fox muscle indicated that trophic position (estimated by δ 15 N) is positively correlated with increasing δ 13 C values, suggesting that Arctic fox with a predominately marine-based foraging strategy occupy a higher trophic level than individuals mostly feeding from a terrestrial-based carbon source. At all sites, the rank order for OC groups in muscle was polychlorinated biphenyls (ΣPCB) > chlordane-related compounds (ΣCHLOR) > hexachlorocyclohexane (ΣHCH) > total toxaphene (TOX) ≥chlorobenzenes (ΣClBz) > DDT-related isomers (ΣDDT). In liver, ΣCHLOR was the most abundant OC group, followed by ΣPCB > TOX > ΣHCH > ΣClBz > ΣDDT. The most abundant OC analytes detected from Arctic fox muscle and liver were oxychlordane, PCB-153, and PCB-180. The comparison of δ 15 N with OC concentrations indicated that relative trophic position might not accurately predict OC bioaccumulation in Arctic fox. The bioaccumulation pattern of OCs in the Arctic fox is similar to the polar bear. While ΣPCB concentrations were highly variable, concentrations in the Arctic fox were generally below those associated with the toxicological endpoints for adverse effects on mammalian reproduction. Further research is required to properly elucidate the potential health impacts to this species from exposure to OCs

  2. Stable isotope and trace element profiling combined with classification models to differentiate geographic growing origin for three fruits: effects of subregion and variety.

    Science.gov (United States)

    Perez, Angela L; Smith, Brian W; Anderson, Kim A

    2006-06-28

    Classifications of geographic growing origin of three fresh fruits combining elemental profiles with various modeling approaches were determined. Elemental analysis (Ca, Cd, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, P, V, and Zn) of strawberry, blueberry, and pear samples was performed using inductively coupled plasma argon atomic emission spectrometer. Bulk stable carbon and nitrogen isotope analyses in pear were performed using mass spectrometry as an alternative fingerprinting technique. Each fruit, strawberry (Fragaria x ananassa), blueberry (Vaccinium caesariense/corymbosum), and pear (Pyrus communis), was analyzed from two growing regions: Oregon vs Mexico, Chile, and Argentina, respectively. Principal component analysis and canonical discriminant analysis were used for data visualization. The data were modeled using linear discriminant function, quadratic discriminant function, neural network, genetic neural network, and hierarchical tree models with successful classification ranging from 70 to 100% depending on commodity and model. Effects of Oregon subregional and variety classification were investigated with similar success rates.

  3. Using elemental profiles and stable isotopes to trace the origin of green coffee beans on the global market.

    Science.gov (United States)

    Santato, Alessandro; Bertoldi, Daniela; Perini, Matteo; Camin, Federica; Larcher, Roberto

    2012-09-01

    A broad elemental profile incorporating 54 elements (Li, Be, B, Na, Mg, Al, P, K, Ca, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, Ge, As, Se, Rb, Sr, Y, Mo, Pd, Ag, Cd, Sn, Sb, Te, Cs, Ba, La, Ce, Pr, Nd, Sm, Eu, Gd, Dy, Er, Tm, Yb, Re, Ir, Pt, Au, Hg, Tl, Pb, Bi and U) in combination with δ(2) H, δ(13) C, δ(15) N and δ(18) O was used to characterise the composition of 62 green arabica (Coffea arabica) and robusta (Coffea canephora) coffee beans grown in South and Central America, Africa and Asia, the four most internationally renowned areas of production. The δ(2) H, Mg, Fe, Co and Ni content made it possible to correctly assign 95% of green coffee beans to the appropriate variety. Canonical discriminant analysis, performed using δ(13) C, δ(15) N, δ(18) O, Li, Mg, P, K, Mn, Co, Cu, Se, Y, Mo, Cd, La and Ce correctly traced the origin of 98% of coffee beans. Copyright © 2012 John Wiley & Sons, Ltd.

  4. Sensitivity Analysis of Distributed Soil Moisture Profiles by Active Distributed Temperature Sensing

    Science.gov (United States)

    Ciocca, F.; Van De Giesen, N.; Assouline, S.; Huwald, H.; Lunati, I.

    2012-12-01

    Monitoring and measuring the fluctuations of soil moisture at large scales in the filed remains a challenge. Although sensors based on measurement of dielectric properties such as Time Domain Reflectometers (TDR) and capacity-based probes can guarantee reasonable responses, they always operate on limited spatial ranges. On the other hand optical fibers, attached to a Distribute Temperature Sensing (DTS) system, can allow for high precision soil temperature measurements over distances of kilometers. A recently developed technique called Active DTS (ADTS) and consisting of a heat pulse of a certain duration and power along the metal sheath covering the optical fiber buried in the soil, has proven a promising alternative to spatially-limited probes. Two approaches have been investigated to infer distributed soil moisture profiles in the region surrounding the optic fiber cable by analyzing the temperature variations during the heating and the cooling phases. One directly relates the change of temperature to the soil moisture (independently measured) to develop specific calibration curve for the soil used; the other requires inferring the thermal properties and then obtaining the soil moisture by inversion of known relationships. To test and compare the two approaches over a broad range of saturation conditions a large lysimeter has been homogeneously filled with loamy soil and 52 meters of fiber optic cable have been buried in the shallower 0.8 meters in a double coil rigid structure of 15 loops along with a series of capacity-based sensors (calibrated for the soil used) to provide independent soil moisture measurements at the same depths of the optical fiber. Thermocouples have also been wrapped around the fiber to investigate the effects of the insulating cover surrounding the cable, and in between each layer in order to monitor heat diffusion at several centimeters. A high performance DTS has been used to measure the temperature along the fiber optic cable. Several

  5. Temperature influences the expression profiling of immune response genes in rainbow trout following DNA vaccination and VHS virus infection

    DEFF Research Database (Denmark)

    Einer-Jensen, Katja; Gautier, Laurent; Rasmussen, Jesper Skou

    -PCR. The expression profiles appeared similar for the two genes in terms of temperature dependency with a faster induction and shorter duration at the higher temperature. In order to analyze the temperature effect on the relative expression profiles across a larger set of immune genes time points displaying similar...... an early unspecific antiviral response as well as a long-lasting specific protection. However, temperature appears to influence immune response with respect to the nature and duration of the protective mechanisms. In this study, groups of fish were temperature acclimated, vaccinated and challenged at three...... different temperatures (5, 10 and 15ºC). Tissue and organ samples were collected at numerous time points post vaccination (pv) and post viral challenge (pch). Then, gene expression levels of a two immune genes (Vig-1 and Mx3) involved in unspecific antiviral response mechanisms were determined by Q...

  6. Evaluation of Temperature and Humidity Profiles of Unified Model and ECMWF Analyses Using GRUAN Radiosonde Observations

    Directory of Open Access Journals (Sweden)

    Young-Chan Noh

    2016-07-01

    Full Text Available Temperature and water vapor profiles from the Korea Meteorological Administration (KMA and the United Kingdom Met Office (UKMO Unified Model (UM data assimilation systems and from reanalysis fields from the European Centre for Medium-Range Weather Forecasts (ECMWF were assessed using collocated radiosonde observations from the Global Climate Observing System (GCOS Reference Upper-Air Network (GRUAN for January–December 2012. The motivation was to examine the overall performance of data assimilation outputs. The difference statistics of the collocated model outputs versus the radiosonde observations indicated a good agreement for the temperature, amongst datasets, while less agreement was found for the relative humidity. A comparison of the UM outputs from the UKMO and KMA revealed that they are similar to each other. The introduction of the new version of UM into the KMA in May 2012 resulted in an improved analysis performance, particularly for the moisture field. On the other hand, ECMWF reanalysis data showed slightly reduced performance for relative humidity compared with the UM, with a significant humid bias in the upper troposphere. ECMWF reanalysis temperature fields showed nearly the same performance as the two UM analyses. The root mean square differences (RMSDs of the relative humidity for the three models were larger for more humid conditions, suggesting that humidity forecasts are less reliable under these conditions.

  7. The Temperature Profile for The Innovative Design of the Perforated Fin

    Directory of Open Access Journals (Sweden)

    Hisham Al-Saddy

    2016-11-01

    Full Text Available The development of the perforated fin had proposed in many studies to enhance the heat transfer from electronic pieces. This paper presents a novel derivative method to find the temperature distribution of the new design (inclined perforated of the pin fin. Perforated with rectangular section and different angles of inclination was considered. Signum Function is used for modeling the variable heat transfer area. Set of parameters to handle the conduction and convection area were calculated. Degenerate Hypergeometric Equation (DHE was used for modeling the Complex energy differential equation and then solved by Kummer’s series. In the validation process, Ansys 16.0-Steady State Thermal was used. Two geometric models were considered. The big reliability of the presented model comes from the high agreement of the validation results about (0.25%. The results show the increase of the inclination leads to the enhancement of the temperature difference and heat transfer ratio. Improved of Heat transfer ratio is ranging from 13% to 50%. Article History: Received June 12th 2016; Received in revised form August 6th 2016; Accepted August 24th 2016; Available online How to Cite This Article: Jasim, H.H and Soylemez, M.S. (2016. The temperature profile for the innovative design of the perforated fin. Int. Journal of Renewable Energy Development, 5(3, 259-266 http://dx.doi.org/10.14710/ijred.5.3.259-266

  8. The clinical profile of women with stable ischaemic heart disease in Spain. More effort is needed in secondary prevention. SIRENA study.

    Science.gov (United States)

    Gámez, J M; Ripoll, T; Barrios, V; Anguita, M; Pedreira, M; Madariaga, I

    2016-01-01

    Cardiovascular diseases are the leading cause of death for women, especially ischaemic heart disease, which is still considered a man's disease. In Spain, there are various registries on ischaemic heart disease, although none are exclusively for women. The objectives of the SIRENA study were to describe the clinical profile of women with ischaemic heart disease treated in cardiology consultations, to estimate its prevalence of cardiovascular risk factors and understand its clinical management. A multicentre observational study was conducted with a sample of 631 women with stable ischaemic heart disease, consecutively included during cardiology consultations. Forty-one researchers from all over Spain participated in the study. The mean age was 68.5 years. The clinical presentation was in the form of acute coronary syndrome in up to 67.2% of the patients. The prevalence of cardiovascular risk factors was high (77.7% of the patients had hypertension, 40.7% had diabetes and 68% had dyslipidaemia), with 30.7% having uncontrolled hypertension, 78.4% having LDL-cholesterol levels higher than 70mg/dL and 49.2% having HbA1c levels greater than 7%. The considerable majority of the patients underwent optimal medical treatment with antiplatelet agents, beta-blockers, renin-angiotensin-aldosterone system blockers and hypolipidaemic agents. Coronary angiography was performed for 88.3% of the patients, and 63.4% underwent percutaneous coronary intervention. Women with stable ischaemic heart disease in Spain initially present some form of acute coronary syndrome and a high prevalence of inadequately controlled cardiovascular risk factors, despite undergoing optimal medical therapy. A high percentage of these women undergo coronary revascularisation. Increased efforts are required for secondary prevention in women with stable ischaemic heart disease. Copyright © 2015 Elsevier España, S.L.U. y Sociedad Española de Medicina Interna (SEMI). All rights reserved.

  9. H, C, N and S stable isotopes and mineral profiles to objectively guarantee the authenticity of grated hard cheeses

    International Nuclear Information System (INIS)

    Camin, Federica; Wehrens, Ron; Bertoldi, Daniela; Bontempo, Luana; Ziller, Luca; Perini, Matteo; Nicolini, Giorgio; Nocetti, Marco; Larcher, Roberto

    2012-01-01

    Graphical abstract: Random Forest model based on δ 13 C, δ 2 H, δ 15 N, δ 34 S and the content of Sr, Cu, Mo, Re, Na, U, Bi, Ni, Fe, Mn, Ga, Se, Er, Dy, Pb, Li, usable for the protection of PDO Parmigiano Reggiano cheese from mislabelling. The correct classification rate in cross-validation is 98.6%. Highlights: ► The isotopic and elemental profile of over 260 hard cheese samples are discussed. ► Two validated and immediately applicable statistical models are presented. ► One model is able to predict the origin of seven types of European hard cheeses. ► The other one allows to discriminate the PDO Parmigiano Reggiano cheese from imitators. ► The most significant variables are δ 13 C, δ 2 H, δ 15 N, δ 34 S and the content of 16 elements. - Abstract: In compliance with the European law (EC No. 510/2006), geographical indications and designations of origin for agricultural products and foodstuffs must be protected against mislabelling. This is particularly important for PDO hard cheeses, as Parmigiano Reggiano, that can cost up to the double of the no-PDO competitors. This paper presents two statistical models, based on isotopic and elemental composition, able to trace the origin of cheese also in grated and shredded forms, for which it is not possible to check the logo fire-marked on the rind. One model is able to predict the origin of seven types of European hard cheeses (in a validation step, 236 samples out of 240 are correctly recognised) and the other specifically to discriminate the PDO Parmigiano Reggiano cheese from 9 European and 2 extra-European imitators (260 out of 264 correct classifications). Both models are based on Random Forests. The most significant variables for cheese traceability common in both models are δ 13 C, δ 2 H, δ 15 N, δ 34 S and Sr, Cu, Mo, Re, Na, U, Bi, Ni, Fe, Mn, Ga, Se, and Li. These variables are linked not only to geography, but also to cow diet and cheese making processes.

  10. The impact of diurnal fasting during Ramadan on the lipid profile, hs-CRP, and serum leptin in stable cardiac patients.

    Science.gov (United States)

    Khafaji, Hadi Abdul Ridha Hadi; Bener, Abdulbari; Osman, Mohammed; Al Merri, Ajayeb; Al Suwaidi, Jassim

    2012-01-01

    To study the effect of strict prolonged fasting on lipid profile, serum leptin, and high- sensitivity C-reactive protein (hs-CRP) in patients with different stable cardiac illnesses and look for associated new cardiac events and any correlation between entire variables. A total of 56 patients of different stable cardiac illnesses were followed in our cardiology outpatient for 3 months. Data concerning their ability to fast were collected: New York Heart Association class of congestive cardiac failure, angina class, previous myocardial infarction, previous coronary artery bypass graft, percutaneous coronary intervention, severity of valvular lesion, metallic prosthetic valve, and traditional risk factors (diabetes mellitus, insulin requirement, hypertension, hypercholesterolemia, smoking habit, and obesity). Detailed clinical examination and electrocardiography were performed in all patients in three consecutive visits before, during, and after Ramadan. Echocardiographic and angiographic findings and medication plans were collected from patient records. Lipid profile, serum leptin, and hs-CRP were assessed before, during, and after Ramadan. All patients fasted during Ramadan: 80.4% were male, 67.9% were aged >50 years, 71.4% had no change in their symptoms during fasting while 28.6% felt better. No patient has deteriorated. 91.1% of the patients were compliant with medicine during Ramadan, 73.2% after. 89.3% were compliant with diet during Ramadan with no significant change in body weight in the follow-up period. No cardiac or noncardiac morbidity or mortality was reported. High- density lipoprotein-cholesterol (HDL-C) decreased significantly during compared to before fasting (P = 0.012). Low-density lipoprotein-cholesterol (LDL-C) significantly increased during compared to before fasting (P = 0.022). No statistically significant changes were observed in total cholesterol (TC), triglycerides (TG), serum leptin, or hs-CRP. Significant correlation was observed between

  11. Acousto-optical and SAW propagation characteristics of temperature stable multilayered structures based on LiNbO3 and diamond

    International Nuclear Information System (INIS)

    Shandilya, Swati; Sreenivas, K; Gupta, Vinay

    2008-01-01

    Theoretical studies on the surface acoustic wave (SAW) properties of c-axis oriented LiNbO 3 /IDT/diamond and diamond/IDT/128 0 rotated Y-X cut LiNbO 3 multilayered structures have been considered. Both layered structures exhibit a positive temperature coefficient of delay (TCD) characteristic, and a zero TCD device is obtained after integrating with an over-layer of either tellurium dioxide (TeO 2 ) or silicon dioxide (SiO 2 ). The presence of a TeO 2 over-layer enhanced the electromechanical coupling coefficients of both multilayered structures, which acts as a better temperature compensation layer than SiO 2 . The temperature stable TeO 2 /LiNbO 3 /IDT/diamond layered structure exhibits good electromechanical coefficient and higher phase velocity for SAW device applications. On the other hand, a high acousto-optical (AO) figure of merit (30-37) x 10 -15 s 3 kg -1 has been obtained for the temperature stable SiO 2 /diamond/IDT/LiNbO 3 layered structure indicating a promising device structure for AO applications

  12. Dominance of pollutant aerosols over an urban region and its impact on boundary layer temperature profile

    Science.gov (United States)

    Talukdar, Shamitaksha; Jana, Soumyajyoti; Maitra, Animesh

    2017-01-01

    Collocated measurements of aerosol optical depth (AOD) and black carbon at different wavelengths over Kolkata, an urban region in eastern India, have been used to calculate aerosol single-scattering albedo (SSA). The wavelength dependence of SSA and AOD has been presented to discriminate the aerosol types over this highly populated metropolitan area. The spectral pattern shows that SSA decreases with wavelength for most of the time in a year and corresponding Ångström coefficient is greater than unity. These optical properties indicate the dominance of fine-mode pollutant particles over the city. The temperature lapse rate profile within the surface boundary layer has been found to be significantly influenced by the heating effect of fine-mode pollutants, and consequently, the growth of the convective processes in the lower troposphere is notably affected. In addition, a back trajectory analysis has also been presented to indicate that transported air masses can have significant impact on spectral pattern of SSA.

  13. Remote Sensing the Vertical Profile of Cloud Droplet Effective Radius, Thermodynamic Phase, and Temperature

    Science.gov (United States)

    Martins, J. V.; Marshak, A.; Remer, L. A.; Rosenfeld, D.; Kaufman, Y. J.; Fernandez-Borda, R.; Koren, I.; Correia, A. L.; Zubko, V.; Artaxo, P.

    2011-01-01

    Cloud-aerosol interaction is a key issue in the climate system, affecting the water cycle, the weather, and the total energy balance including the spatial and temporal distribution of latent heat release. Information on the vertical distribution of cloud droplet microphysics and thermodynamic phase as a function of temperature or height, can be correlated with details of the aerosol field to provide insight on how these particles are affecting cloud properties and their consequences to cloud lifetime, precipitation, water cycle, and general energy balance. Unfortunately, today's experimental methods still lack the observational tools that can characterize the true evolution of the cloud microphysical, spatial and temporal structure in the cloud droplet scale, and then link these characteristics to environmental factors and properties of the cloud condensation nuclei. Here we propose and demonstrate a new experimental approach (the cloud scanner instrument) that provides the microphysical information missed in current experiments and remote sensing options. Cloud scanner measurements can be performed from aircraft, ground, or satellite by scanning the side of the clouds from the base to the top, providing us with the unique opportunity of obtaining snapshots of the cloud droplet microphysical and thermodynamic states as a function of height and brightness temperature in clouds at several development stages. The brightness temperature profile of the cloud side can be directly associated with the thermodynamic phase of the droplets to provide information on the glaciation temperature as a function of different ambient conditions, aerosol concentration, and type. An aircraft prototype of the cloud scanner was built and flew in a field campaign in Brazil.

  14. Body temperature, activity and melatonin profiles in adults with attention-deficit/hyperactivity disorder and delayed sleep: a case-control study.

    Science.gov (United States)

    Bijlenga, Denise; Van Someren, Eus J W; Gruber, Reut; Bron, Tannetje I; Kruithof, I Femke; Spanbroek, Elise C A; Kooij, J J Sandra

    2013-12-01

    Irregular sleep-wake patterns and delayed sleep times are common in adults with attention-deficit/hyperactivity disorder, but mechanisms underlying these problems are unknown. The present case-control study examined whether circadian abnormalities underlie these sleep problems in a naturalistic home setting. We included 12 medication-naïve patients with attention-deficit/hyperactivity disorder and delayed sleep phase syndrome, and 12 matched healthy controls. We examined associations between sleep/wake rhythm in attention-deficit/hyperactivity disorder and circadian parameters (i.e. salivary melatonin concentrations, core and skin temperatures, and activity patterns) of the patients and controls during five consecutive days and nights. Daily bedtimes were more variable within patients compared with controls (F = 8.19, P profiles were equally stable within individuals. Dim-light melatonin onset was about 1.5 h later in the patient group (U = 771, Z = -4.63, P temperatures were delayed to comparable degrees in patients. Overall temperatures were lower in patients than controls. Sleep-onset difficulties correlated with greater distal-proximal temperature gradient (DPG; i.e. colder hands, r(2)  = -0.32, P = 0.028) in patients. Observed day-to-day bedtime variability of individuals with attention-deficit/hyperactivity disorder and delayed sleep phase syndrome were not reflected in their melatonin profiles. Irregular sleep-wake patterns and delayed sleep in individuals with attention-deficit/hyperactivity disorder and delayed sleep phase syndrome are associated with delays and dysregulations of the core and skin temperatures. © 2013 European Sleep Research Society.

  15. Cystic fibrosis transmembrane conductance regulator: temperature-dependent cysteine reactivity suggests different stable conformers of the conduction pathway.

    Science.gov (United States)

    Liu, Xuehong; Dawson, David C

    2011-11-29

    Cysteine scanning has been widely used to identify pore-lining residues in mammalian ion channels, including the cystic fibrosis transmembrane conductance regulator (CFTR). These studies, however, have been typically conducted at room temperature rather than human body temperature. Reports of substantial effects of temperature on gating and anion conduction in CFTR channels as well as an unexpected pattern of cysteine reactivity in the sixth transmembrane segment (TM6) prompted us to investigate the effect of temperature on the reactivity of cysteines engineered into TM6 of CFTR. We compared reaction rates at temperatures ranging from 22 to 37 °C for cysteines placed on either side of an apparent size-selective accessibility barrier previously defined by comparing reactivity toward channel-permeant and channel-impermeant, thiol-directed reagents. The results indicate that the reactivity of cysteines at three positions extracellular to the position of the accessibility barrier, 334, 336, and 337, is highly temperature-dependent. At 37 °C, cysteines at these positions were highly reactive toward MTSES(-), whereas at 22 °C, the reaction rates were 2-6-fold slower to undetectable. An activation energy of 157 kJ/mol for the reaction at position 337 is consistent with the hypothesis that, at physiological temperature, the extracellular portion of the CFTR pore can adopt conformations that differ significantly from those that can be accessed at room temperature. However, the position of the accessibility barrier defined empirically by applying channel-permeant and channel-impermeant reagents to the extracellular aspect of the pore is not altered. The results illuminate previous scanning results and indicate that the assay temperature is a critical variable in studies designed to use chemical modification to test structural models for the CFTR anion conduction pathway.

  16. Gene expression profile indicates involvement of NO in Camellia sinensis pollen tube growth at low temperature.

    Science.gov (United States)

    Pan, Junting; Wang, Weidong; Li, Dongqin; Shu, Zaifa; Ye, Xiaoli; Chang, Pinpin; Wang, Yuhua

    2016-10-18

    temperature and NO are identified in this study. The transcriptomic gene expression profiles present a valuable genomic tool to improve studying the molecular mechanisms underlying low-temperature tolerance in pollen tube.

  17. Profiles

    International Nuclear Information System (INIS)

    2004-01-01

    Profiles is a synthetic overview of more than 100 national energy markets in the world, providing insightful facts and key energy statistics. A Profile is structured around 6 main items and completed by key statistics: Ministries, public agencies, energy policy are concerned; main companies in the oil, gas, electricity and coal sectors, status, shareholders; reserve, production, imports and exports, electricity and refining capacities; deregulation of prices, subsidies, taxes; consumption trends by sector, energy market shares; main energy projects, production and consumption prospects. Statistical Profiles are present in about 3 pages the main data and indicators on oil, gas, coal and electricity. (A.L.B.)

  18. Bias Correction for Assimilation of Retrieved AIRS Profiles of Temperature and Humidity

    Science.gov (United States)

    Blakenship, Clay; Zavodsky, Bradley; Blackwell, William

    2014-01-01

    The Atmospheric Infrared Sounder (AIRS) is a hyperspectral radiometer aboard NASA's Aqua satellite designed to measure atmospheric profiles of temperature and humidity. AIRS retrievals are assimilated into the Weather Research and Forecasting (WRF) model over the North Pacific for some cases involving "atmospheric rivers". These events bring a large flux of water vapor to the west coast of North America and often lead to extreme precipitation in the coastal mountain ranges. An advantage of assimilating retrievals rather than radiances is that information in partly cloudy fields of view can be used. Two different Level 2 AIRS retrieval products are compared: the Version 6 AIRS Science Team standard retrievals and a neural net retrieval from MIT. Before assimilation, a bias correction is applied to adjust each layer of retrieved temperature and humidity so the layer mean values agree with a short-term model climatology. WRF runs assimilating each of the products are compared against each other and against a control run with no assimilation. Forecasts are against ERA reanalyses.

  19. Temperature profiles in a multi-partitioned air-filled square cavity

    Energy Technology Data Exchange (ETDEWEB)

    Ampofo, F.; Karayiannis, T.G.; Tian, Y.S.; Gabbitas, B.L. [South Bank University, London (United Kingdom). School of Engineering Systems and Design; Wu, J.Z. [Concentration Heat and Momentum Ltd., London (United Kingdom)

    1999-07-01

    An experimental study of temperature profiles in a low-level turbulence natural convection in a multi-partitioned air filled vertical square cavity was conducted. The cavity was 0.75 m high x 0.75 m wide x 1.5 m deep giving 2-D flow. The hot and cold walls of the cavity were isothermal at 50{sup o}C and 10{sup o}C respectively giving a Ra number of 1.58 x 10{sup 9}. A non-uniform mesh was used in the temperature distribution measurements and an experimentally obtained contour plot of the thermal field in such a 'congested' cavity is reported for the first time. The local and average Nusselt numbers are also presented. The experiments were conducted with very high accuracy and as such the results can form experimental benchmark data and will be useful for validation of Computational Fluid Dynamics (CFD) codes used both in the electronic and building industries. (author)

  20. Field measurements of temperature profile for floatovoltaic dryer in the tropics

    Science.gov (United States)

    Osman, F. A.; Ya'acob, M. E.; Iskandar, A. Noor

    2017-09-01

    Most of the equator region in a tropical climate zone experiences hot and humid weather but sometimes heavy rain and thunderstorms which occur stochastically in monsoon season. Sunlight which is the energy source can be harvested approximately 8 hours (on average basis) daily throughout the year which leads to the promotion of Solar PV technologies. This works projects the field performance for a new Floatovoltaic Dryer prototype with flexible PV roofing structures covering the top of the dryer system. The field measurements are collected on the lake of Engineering Faculty, UPM supported with 4-parameter weather station. Temperature profile with RH measurements inside the Floatovoltaic Dryer compartments as compared to direct-sun drying mechanism are the main contributions of this work and it projects more than 12 W of convection heat energy could be harvested by using the clean system. The field measurements imply various points of thermocouple and humidity sensor throughout the experiment. Temperature and humidity will be the main elements recorded to analyze the differences under monocrystalline PV panel as compared to natural drying.

  1. Processes of Equatorial Thermal Structure: An Analysis of Galileo Temperature Profile with 3-D Model

    Science.gov (United States)

    Majeed, T.; Waite, J. H., Jr.; Bougher, S. W.; Gladstone, G. R.

    2005-01-01

    The Jupiter Thermosphere General Circulation Model (JTGCM) calculates the global dynamical structure of Jupiter's thermosphere self-consistently with its global thermal structure and composition. The main heat source that drives the thermospheric flow is high-latitude Joule heating. A secondary source of heating is the auroral process of particle precipitation. Global simulations of Jovian thermospheric dynamics indicate strong neutral outflows from the auroral ovals with velocities up to approximately 2 kilometers per second and subsequent convergence and downwelling at the Jovian equator. Such circulation is shown to be an important process for transporting significant amounts of auroral energy to equatorial latitudes and for regulating the global heat budget in a manner consistent with the high thermospheric temperatures observed by the Galileo probe. Adiabatic compression of the neutral atmosphere resulting from downward motion is an important source of equatorial heating (less than 0.06 microbar). The adiabatic heating continues to dominate between 0.06 and 0.2 microbar, but with an addition of comparable heating due to horizontal advection induced by the meridional flow. Thermal conduction plays an important role in transporting heat down to lower altitudes (greater than 0.2microbar) where it is balanced by the cooling associated with the wind transport processes. Interestingly, we find that radiative cooling caused by H3(+), CH4, and C2H2 emissions does not play a significant role in interpreting the Galileo temperature profile.

  2. Atmospheric temperature profiles derived through the inversion of a system of first order differential equations. [radiance data from satellite sounder

    Science.gov (United States)

    Gatlin, J. A.; Englar, T. S.

    1976-01-01

    Generation of vertical temperatures profiles from remotely sensed atmospheric radiance data is described as an analogous communications system. The radiative transport characteristics of the atmosphere encodes the continuous temperature profile into an 'n' element vector where 'n' is the number of channels in the satellite instrument. The temperature profile is a message transmitted from station A to station B and the link is the satellite instrument. At station B the decoder reproduces a continuous function which is the best estimate of the message encoded at station A. It is shown that the decoder must operate in a tuned mode where the parameters used in the encoder precisely determine the decoder parameters, and that the characteristics of the total message block must be given by a set of decoder constraints

  3. Not completely flattened radial profile of the electron temperature in the vicinity of magnetic islands in Tokamak Chauffage Alfven Bresilien

    International Nuclear Information System (INIS)

    Fonseca, A.M.M.; Tsypin, V.S.; Galvao, R.M.O.; Kuznetsov, Y.K.; Nascimento, I.C.; Silva, R.P. da; Saettone, E.A.; Vannucci, A.

    2005-01-01

    Recent results obtained in TCABR (Tokamak Chauffage Alfven Bresilien) [J. H. F. Severo, I. C. Nascimento, V. S. Tsypin, and R. M. O. Galvao, Nucl. Fusion 43, 1047 (2003)] show a nonmonotonic variation of the poloidal rotation velocity at the position of major magnetic islands. In this paper, the associated effect of the magnetic islands on the radial profile of the electron temperature is discussed. Analytical temperature profiles are used to analyze the experimental data obtained with electron cyclotron emission radiometry. It is shown that the competition between strong anomalous perpendicular diffusive transport and parallel heat convection is the dominant mechanism for the oscillations observed in the radial profile of the electron temperature in TCABR

  4. High-temperature pyrolysis/gas chromatography/isotope ratio mass spectrometry: simultaneous measurement of the stable isotopes of oxygen and carbon in cellulose.

    Science.gov (United States)

    Woodley, Ewan J; Loader, Neil J; McCarroll, Danny; Young, Giles H F; Robertson, Iain; Heaton, Timothy H E; Gagen, Mary H; Warham, Joseph O

    2012-01-30

    Stable isotope analysis of cellulose is an increasingly important aspect of ecological and palaeoenvironmental research. Since these techniques are very costly, any methodological development which can provide simultaneous measurement of stable carbon and oxygen isotope ratios in cellulose deserves further exploration. A large number (3074) of tree-ring α-cellulose samples are used to compare the stable carbon isotope ratios (δ(13)C) produced by high-temperature (1400°C) pyrolysis/gas chromatography (GC)/isotope ratio mass spectrometry (IRMS) with those produced by combustion GC/IRMS. Although the two data sets are very strongly correlated, the pyrolysis results display reduced variance and are strongly biased towards the mean. The low carbon isotope ratios of tree-ring cellulose during the last century, reflecting anthropogenic disturbance of atmospheric carbon dioxide, are thus overestimated. The likely explanation is that a proportion of the oxygen atoms are bonding with residual carbon in the reaction chamber to form carbon monoxide. The 'pyrolysis adjustment', proposed here, is based on combusting a stratified sub-sample of the pyrolysis results, across the full range of carbon isotope ratios, and using the paired results to define a regression equation that can be used to adjust all the pyrolysis measurements. In this study, subsamples of 30 combustion measurements produced adjusted chronologies statistically indistinguishable from those produced by combusting every sample. This methodology allows simultaneous measurement of the stable isotopes of carbon and oxygen using high-temperature pyrolysis, reducing the amount of sample required and the analytical costs of measuring them separately. Copyright © 2011 John Wiley & Sons, Ltd.

  5. Spring-Summer Temperatures Since AD 1780 Reconstructed from Stable Oxygen Isotope Ratios in White Spruce Tree-Rings from the Mackenzie Delta, Northwestern Canada

    Science.gov (United States)

    Porter, Trevor J.; Pisaric, Michael F. J.; Field, Robert D.; Kokelj, Steven V.; Edwards, Thomas W. D.; deMontigny, Peter; Healy, Richard; LeGrande, Allegra N.

    2013-01-01

    High-latitude delta(exp 18)O archives deriving from meteoric water (e.g., tree-rings and ice-cores) can provide valuable information on past temperature variability, but stationarity of temperature signals in these archives depends on the stability of moisture source/trajectory and precipitation seasonality, both of which can be affected by atmospheric circulation changes. A tree-ring delta(exp 18)O record (AD 1780-2003) from the Mackenzie Delta is evaluated as a temperature proxy based on linear regression diagnostics. The primary source of moisture for this region is the North Pacific and, thus, North Pacific atmospheric circulation variability could potentially affect the tree-ring delta(exp 18)O-temperature signal. Over the instrumental period (AD 1892-2003), tree-ring delta(exp 18)O explained 29% of interannual variability in April-July minimum temperatures, and the explained variability increases substantially at lower-frequencies. A split-period calibration/verification analysis found the delta(exp 18)O-temperature relation was time-stable, which supported a temperature reconstruction back to AD 1780. The stability of the delta(exp 18)O-temperature signal indirectly implies the study region is insensitive to North Pacific circulation effects, since North Pacific circulation was not constant over the calibration period. Simulations from the NASA-GISS ModelE isotope-enabled general circulation model confirm that meteoric delta(exp 18)O and precipitation seasonality in the study region are likely insensitive to North Pacific circulation effects, highlighting the paleoclimatic value of tree-ring and possibly other delta(exp 18)O records from this region. Our delta(exp 18)O-based temperature reconstruction is the first of its kind in northwestern North America, and one of few worldwide, and provides a long-term context for evaluating recent climate warming in the Mackenzie Delta region.

  6. Molecular dynamic simulation of Ar-Kr mixture across a rough walled nanochannel: Velocity and temperature profiles

    International Nuclear Information System (INIS)

    Pooja,; Ahluwalia, P. K.; Pathania, Y.

    2015-01-01

    This paper presents the results from a molecular dynamics simulation of mixture of argon and krypton in the Poiseuille flow across a rough walled nanochannel. The roughness effect on liquid nanoflows has recently drawn attention The computational software used for carrying out the molecular dynamics simulations is LAMMPS. The fluid flow takes place between two parallel plates and is bounded by horizontal rough walls in one direction and periodic boundary conditions are imposed in the other two directions. Each fluid atom interacts with other fluid atoms and wall atoms through Leenard-Jones (LJ) potential with a cut off distance of 5.0. To derive the flow a constant force is applied whose value is varied from 0.1 to 0.3 and velocity profiles and temperature profiles are noted for these values of forces. The velocity profile and temperature profiles are also looked at different channel widths of nanochannel and at different densities of mixture. The velocity profile and temperature profile of rough walled nanochannel are compared with that of smooth walled nanochannel and it is concluded that mean velocity increases with increase in channel width, force applied and decrease in density also with introduction of roughness in the walls of nanochannel mean velocity again increases and results also agree with the analytical solution of a Poiseuille flow

  7. Molecular dynamic simulation of Ar-Kr mixture across a rough walled nanochannel: Velocity and temperature profiles

    Energy Technology Data Exchange (ETDEWEB)

    Pooja,, E-mail: pupooja16@gmail.com; Ahluwalia, P. K., E-mail: pk-ahluwalia7@yahoo.com [Department. of Physics, Himachal Pradesh University, Shimla, H. P., 171005 (India); Pathania, Y. [GGDSD College Sec-32-C Chandigarh (India)

    2015-05-15

    This paper presents the results from a molecular dynamics simulation of mixture of argon and krypton in the Poiseuille flow across a rough walled nanochannel. The roughness effect on liquid nanoflows has recently drawn attention The computational software used for carrying out the molecular dynamics simulations is LAMMPS. The fluid flow takes place between two parallel plates and is bounded by horizontal rough walls in one direction and periodic boundary conditions are imposed in the other two directions. Each fluid atom interacts with other fluid atoms and wall atoms through Leenard-Jones (LJ) potential with a cut off distance of 5.0. To derive the flow a constant force is applied whose value is varied from 0.1 to 0.3 and velocity profiles and temperature profiles are noted for these values of forces. The velocity profile and temperature profiles are also looked at different channel widths of nanochannel and at different densities of mixture. The velocity profile and temperature profile of rough walled nanochannel are compared with that of smooth walled nanochannel and it is concluded that mean velocity increases with increase in channel width, force applied and decrease in density also with introduction of roughness in the walls of nanochannel mean velocity again increases and results also agree with the analytical solution of a Poiseuille flow.

  8. Quantitative explanation of some electron temperature profiles measured in situ in the high latitude ionospheric E-region

    International Nuclear Information System (INIS)

    Schlegel, K.; Oyama, Koh-ichiro; Hirao, Kunio

    1983-01-01

    E region electron temperature profiles obtained with a rocket experiment in the Antarctica are compared to theoretical electron temperatures calculated from a model. The main heat source in this model is the heating of the electron gas by unstable plasma waves. Very good agreement between both temperatures is obtained between 105 and 115 km altitude, where this heating mechanism is effective. The agreement is also good below this altitude range, after a refinement of the data analysis procedure for the measured temperatures. Several important consequences of the good agreement are pointed out. (author)

  9. Climatology and trends of mesospheric (58-90) temperatures based upon 1982-1986 SME limb scattering profiles

    Science.gov (United States)

    Clancy, R. Todd; Rusch, David W.

    1989-01-01

    Atmospheric temperature profiles for the altitude range 58-90 km were calculated using data on global UV limb radiances from the SME satellite. The major elements of this climatology include a high vertical resolution (about 4 km) and the coverage of the 70-90 km altitude region. The analysis of this extensive data set provides a global definition of mesospheric-lower thermospheric temperature trends over the 1982-1986 period. The observations suggest a pattern of 1-2 K/year decreases in temperatures at 80-90-km altitudes accompanied by 0.5-1.5 K/year increases in temperatures at 65-80-km altitudes.

  10. Stable isotope record of Eemian seasonal temperature from MIS 5e tufa stromatolite; Somme Basin, Northern France

    Science.gov (United States)

    Dabkowski, J.; Andrews, J.; Antoine, P.; Marca-Bell, A.

    2013-03-01

    In many modern to sub-fossil deposits tufa formations, very well crystallised deposits called stromatolites are preserved. These are often strongly laminated deposits, the laminae linked to seasonal climatic and environmental variations. Where found in fossil tufas such deposits have huge potential as high resolution archives of Pleistocene climate. One of the first investigations of this type has been performed on a 2.5 cm-radius stromatolite from the Eemian sequence of Caours (Somme Basin, Northern France), where precise observations in thin section have been combined with intra-lamina δ18O and δ13C analyses. Independent interpretations of petrographical and geochemical data are strongly coherent and demonstrate a clear seasonal signal. Moreover, as δ18O is temperature dependent, we have quantified likely maximum water temperature variations between summer and winter at Caours. A small mismatch between the δ18O derived temperature values and the typical modern range is observed, which may reflect a real difference between modern and Eemian temperature seasonality. This study supports previous investigations performed on a laminated tufa from central Greece and clearly confirms the potential of tufa stromatolites as records of seasonal climatic information and for the quantification of riverine water temperature variations.

  11. BELINDA: Broadband Emission Lidar with Narrowband Determination of Absorption. A new concept for measuring water vapor and temperature profiles

    Science.gov (United States)

    Theopold, F. A.; Weitkamp, C.; Michaelis, W.

    1992-01-01

    We present a new concept for differential absorption lidar measurements of water vapor and temperature profiles. The idea is to use one broadband emission laser and a narrowband filter system for separation of the 'online' and 'offline' return signals. It is shown that BELINDA offers improvements as to laser emission shape and stability requirements, background suppression, and last and most important a significant reduction of the influence of Rayleigh scattering. A suitably designed system based on this concept is presented, capable of measuring water vapor or temperature profiles throughout the planetary boundary layer.

  12. AROTAL Ozone and Temperature Vertical Profile Measurements from the NASA DC-8 during the SOLVE II Campaign

    Science.gov (United States)

    McGee, Thomas J.; Twigg, Laurence; Sumnicht, Grant; Hoegy, Walter; Burris, John; Silbert, Donald; Heaps, William; Neuber, R.; Trepte, C. R.

    2004-01-01

    The AROTAL instrument (Airborne Raman Ozone Temperature and Aerosol Lidar) - a collaboration between scientists at NASA Goddard Space Flight Center, and Langley Research Center - was flown on the NASA DC-8 during the SOLVE II Campaign during January and February, 2003. The flights were flown from the Arena Arctica in Kiruna, Sweden. We report measurements of temperature and ozone profiles showing approximately a 600 ppbv loss in ozone near 17.5 km, over the time frame of the aircraft campaign. Comparisons of ozone profiles from AROTAL are made with the SAGE III instrument.

  13. Room temperature stable carbetocin for the prevention of postpartum haemorrhage during the third stage of labour in women delivering vaginally: study protocol for a randomized controlled trial.

    Science.gov (United States)

    Widmer, Mariana; Piaggio, Gilda; Abdel-Aleem, Hany; Carroli, Guillermo; Chong, Yap-Seng; Coomarasamy, Arri; Fawole, Bukola; Goudar, Shivaprasad; Hofmeyr, G Justus; Lumbiganon, Pisake; Mugerwa, Kidza; Nguyen, Thi My Huong; Qureshi, Zahida; Souza, Joao Paulo; Gülmezoglu, A Metin

    2016-03-17

    Postpartum haemorrhage (PPH) is the leading cause of maternal mortality in low-income countries and contributes to nearly a quarter of maternal deaths globally. The current available interventions for prevention of postpartum haemorrhage, oxytocin and carbetocin, are limited by their need for refrigeration to maintain potency, as the ability to maintain a cold chain across the drug distribution and storage network is inconsistent, thus restricting their use in countries with the highest burden of maternal mortality. We describe a randomized, double-blind non-inferiority trial comparing a newly developed room temperature stable formulation of carbetocin to the standard intervention (oxytocin) for the prevention of PPH after vaginal birth. Approximately 30,000 women delivering vaginally will be recruited across 22 centres in 10 countries. The primary objectives are to evaluate the non-inferiority of room temperature stable carbetocin (100 μg intramuscular) versus oxytocin (10 IU intramuscular) in the prevention of PPH and severe PPH after vaginal birth. The primary endpoints are blood loss ≥500 mL or the use of additional uterotonics (composite endpoint required by drug regulatory authorities) and blood loss ≥1,000 mL (WHO requirement). Non-inferiority will be assessed using a two-sided 95 % confidence interval for the relative risk of the above endpoints for room temperature stable carbetocin versus oxytocin. The upper limit of the two-sided 95 % confidence interval for the relative risk for the composite endpoint of blood loss ≥500 mL or the use of additional uterotonics, and for the endpoint of blood loss ≥1,000 mL, will be compared to a non-inferiority margin of 1.16 and 1.23, respectively. If the upper limit is below the corresponding margin, non-inferiority will have been demonstrated. The safety analysis will include all women receiving treatment. Safety and tolerability will be assessed by a review of adverse events, by conducting inferential testing

  14. Oceanographic profile temperature, salinity collected using bottle in the Barents, Kara, Laptev, White, Norwegian Seas from 1977-1998 (NODC Accession 0002294)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Oceanographic profile temperature, salinity collected using bottle in the Barents, Kara, Laptev, White, Norwegian Seas from 1977-1998. Profile data received at NODC...

  15. Lidar Observation of Aerosol and Temperature Stratification over Urban Area During the Formation of a Stable Atmospheric PBL

    Science.gov (United States)

    Kolev, I.; Parvanov, O.; Kaprielov, B.; Mitev, V.; Simeonov, V.; Grigorov, I.

    1992-01-01

    In recent years, the processes in the atmospheric planetary boundary layer (PBL) over urban areas were intensely investigated, due to ecological problems related to the air, soil, and water pollution. New pollution sources in new residential districts, when in contradiction to the microclimate and topography requirements of that region, create a number of considerable hazards and problems. The present study is a continuation of our preceding investigations and aims at revealing the aerosol structure and stratification during the transition after sunset as measured by two lidars. Such observation of the nocturnal, stable PBL formation over an urban area in Bulgaria has not been reported before. The lidars' high time and spatial resolutions allow the changes of the internal structure of the PBL's part located above the surface layer to be observed.

  16. Stable isotope N-phosphoryl amino acids labeling for quantitative profiling of amine-containing metabolites using liquid chromatography mass spectrometry.

    Science.gov (United States)

    Zhang, Shanshan; Shi, Jinwen; Shan, Changkai; Huang, Chengting; Wu, Yile; Ding, Rong; Xue, Yuhua; Liu, Wen; Zhou, Qiang; Zhao, Yufen; Xu, Pengxiang; Gao, Xiang

    2017-07-25

    Stable isotope chemical labeling liquid chromatography-mass spectrometry (LC-MS) is a powerful strategy for comprehensive metabolomics profiling, which can improve metabolites coverage and quantitative information for exploration of metabolic regulation in complex biological systems. In the current work, a novel stable isotope N-phosphoryl amino acids labeling strategy (SIPAL) has been successful developed for quantitative profiling of amine-containing metabolites in urine based on organic phosphorus chemistry. Two isotopic reagents, 16 O 2 - and 18 O 2 -N-diisopropyl phosphoryl l-alanine N-hydroxysuccinimide esters ( 16 O/ 18 O-DIPP-L-Ala-NHS), were firstly synthesized in high yields for labeling the amine-containing metabolites. The performance of SIPAL strategy was tested by analyzing standard samples including 20 l-amino acids, 10 d-amino acids and small peptides by using LC-MS. We observed highly efficient and selective labeling for SIPAL strategy within 15 min in a one-pot derivatization reaction under aqueous reaction conditions. The introduction of a neutral phosphate group at N-terminus can increase the proton affinity and overall hydrophobicity of targeted metabolites, leading to the better ionization efficiency in electrospray ionization processes and chromatographic separations of hydrophilic metabolites on reversed-phase column. Furthermore, the chiral metabolites, such as d-amino acids, could be converted to diastereomers after SIPAL and successfully separated on regular reversed-phase column. The chirality of labeled enantiomers can be determined by using different detection methods such as 31 P NMR, UV, and MS, demonstrating the potential application of SIPAL strategy. In addition, absolute quantification of chiral metabolites in biological samples can be easily achieved by using SIPAL strategy. For this purpose, urine samples collected from a healthy volunteer were analyzed by using LC-ESI-Orbitrap MS. Over 300 pairs of different amine

  17. Partitioning of evapotranspiration using a stable isotope technique in an arid and high temperature agricultural production system

    KAUST Repository

    Lu, Xuefei

    2016-08-22

    Agricultural production in the hot and arid low desert systems of southern California relies heavily on irrigation. A better understanding of how much and to what extent irrigated water is transpired by crops relative to being lost through evaporation would improve the management of increasingly limited water resources. In this study, we examined the partitioning of evapotranspiration (ET) over a field of forage sorghum (Sorghum bicolor), which was under evaluation as a potential biofuel feedstock, based on isotope measurements of three irrigation cycles at the vegetative stage. This study employed customized transparent chambers coupled with a laser-based isotope analyzer to continuously measure near-surface variations in the stable isotopic composition of evaporation (E, δ), transpiration (T, δ) and ET (δ) to partition the total water flux. Due to the extreme heat and aridity, δ and δ were very similar, which makes this system highly unusual. Contrary to an expectation that the isotopic signatures of T, E, and ET would become increasingly enriched as soils became drier, our results showed an interesting pattern that δ, δ, and δ increased initially as soil water was depleted following irrigation, but decreased with further soil drying in mid to late irrigation cycle. These changes are likely caused by root water transport from deeper to shallower soil layers. Results indicate that about 46% of the irrigated water delivered to the crop was used as transpiration, with 54% lost as direct evaporation. This implies that 28 − 39% of the total source water was used by the crop, considering the typical 60 − 85% efficiency of flood irrigation. The stable isotope technique provided an effective means of determining surface partitioning of irrigation water in this unusually harsh production environment. The results suggest the potential to further minimize unproductive water losses in these production systems.

  18. Gradual crossover in molecular organization of stable liquid H2O at moderately high pressure and temperature

    DEFF Research Database (Denmark)

    Koga, Yoshikata; Westh, Peter; Yoshida, Koh

    2014-01-01

    Using the literature raw data of the speed of sound and the specific volume, the isothermal compressibility, κ T , a second derivative thermodynamic quantity of G, was evaluated for liquid H2O in the pressure range up to 350 MPa and the temperature to 50 ºC. We then obtained its pressure derivati...

  19. Stable and solid pellets of functionalized multi-walled carbon nanotubes produced under high pressure and temperature

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Pâmela Andréa Mantey dos [Universidade Federal do Rio Grande do Sul, UFRGS, Programa de Pós-Graduação em Ciência dos Materiais (Brazil); Gallas, Marcia Russman [Universidade Federal do Rio Grande do Sul, UFRGS, Instituto de Física (Brazil); Radtke, Cláudio; Benvenutti, Edilson Valmir [Universidade Federal do Rio Grande do Sul, UFRGS, Instituto de Química (Brazil); Elias, Ana Laura [The Pennsylvania State University, Department of Physics and Center for 2-D and Layered Materials (United States); Rajukumar, Lakshmy Pulickal [The Pennsylvania State University, Department of Materials Science and Engineering (United States); Terrones, Humberto [Rensselaer Polytechnic Institute, Department of Physics, Applied Physics and Astronomy (United States); Endo, Morinobu [Shinshu University, Carbon Institute of Science and Technology (Japan); Terrones, Mauricio [The Pennsylvania State University, Department of Physics and Center for 2-D and Layered Materials (United States); Costa, Tania Maria Haas, E-mail: taniaha@iq.ufrgs.br, E-mail: taniahac@gmail.com [Universidade Federal do Rio Grande do Sul, UFRGS, Programa de Pós-Graduação em Ciência dos Materiais (Brazil)

    2015-06-15

    High pressure/temperature was applied on samples of pristine multi-walled carbon nanotubes (MWCNT), functionalized nanotubes (f-MWCNT), and nanotubes doped with nitrogen (CN{sub x}MWNT). Cylindrical compact pellets of f-MWCNT with diameters of about 6 mm were obtained under pressure of 4.0 GPa at room temperature and at 400 °C, using graphite as pressure transmitting medium. The best pellet samples were produced using nitric and sulfuric acids for the functionalization of MWCNT. The effect of high pressure/temperature on CNT was investigated by several spectroscopy and characterization techniques, such as Raman spectroscopy, X-ray powder diffraction, X-ray photoelectron spectroscopy, N{sub 2} adsorption/desorption isotherms, and transmission electron microscopy. It was found that MWCNT maintain their main features in the compacted pellets, such as integrity, original morphology, and structure, demonstrating that high-pressure/temperature compaction can indeed be used to fabricate novel CNT self-supported materials. Additionally, the specific surface area and porosity are unchanged, which is important when using bulk CNT in adsorption processes. Raman analysis of the G’-band showed a shift to lower wavenumbers when f-MWCNT were processed under high pressure, suggesting that CNT are under tensile stress.

  20. Oxylipin profile and antioxidant status of potato tubers during extended storage at room temperature.

    Science.gov (United States)

    Delaplace, Pierre; Rojas-Beltran, Jorge; Frettinger, Patrick; du Jardin, Patrick; Fauconnier, Marie-Laure

    2008-12-01

    Potato tubers (cv. Bintje) (Solanum tuberosum L.) were stored under extreme conditions at 20 degrees C for 350 days without sprout inhibitors in order to assess whether aging- and/or senescence-related processes occurred. Under these extreme storage conditions, multiple sprouting followed by the formation of daughter tubers occurs. At the same time, an increase in respiration intensity, as evidenced by cytochrome c oxidase activity (E.C. 1.9.3.1), is observed, leading to a potential increase in reactive oxygen species (ROS) production. As polyunsaturated fatty acids are priority targets of oxidative attacks, the damage to lipids was assessed by oxylipin profiling in both free and esterified forms. Oxylipin profiling showed a predominance of linoleic acid-derived oxylipins and of 9-hydroxy and 9-hydroperoxy fatty acids in both free and esterified forms. No significant accumulation of individual oxylipin was observed 350 days after harvest. To further understand the absence of lipid breakdown products accumulation, the main enzymatic and non-enzymatic antioxidants were assessed. Antioxidant enzyme activities [superoxide dismutase (E.C. 1.15.1.1), catalase (E.C. 1.11.1.6.), ascorbate peroxidase (E.C. 1.11.1.11)] were enhanced during the advanced phase of aging. The main non-enzymatic antioxidant compound, ascorbate, decreased markedly in the early stages of storage, followed by a slower decline. Total radical scavenging activity was also maintained at the end of the storage period. Our results indicate that the enhanced aging process occurring during storage at room temperature does not seem to be associated with the changes classically encountered during leaf senescence or seed aging and that the observed degenerative processes do not surpass the protective potential of the tubers.

  1. Investigations of physical processes affecting leaf temperature profiles and primary production in the red mangrove ecosystem. Modification 8 progress report

    Energy Technology Data Exchange (ETDEWEB)

    Miller, P.C.

    Profiles of carbon dioxide, air temperature, and vapor density were measured in a red mangrove canopy in south Florida. Results indicated that the microclimate model will predict profiles of air temperature within 2/sup 0/C, humidity within 1 g m/sup -3/, and CO/sub 2/ levels within 1 ppM through the vegetation canopy. Simulations of mangrove response to thermal additions indicate that in the subtropical climate photosynthesis is increased in winter and decreased in summer by thermal additions, but in tropical climates photosynthesis is decreased throughout the year. Studies on seedlings of South Florida mangroves, Rhizophora mangle, Avicennia germinans, and Laguncularia racemosa, indicated that short-term effects of higher root temperatures cause less water stress than cooler root temperature. (HLW)

  2. THE REDSHIFT EVOLUTION OF THE MEAN TEMPERATURE, PRESSURE, AND ENTROPY PROFILES IN 80 SPT-SELECTED GALAXY CLUSTERS

    Energy Technology Data Exchange (ETDEWEB)

    McDonald, M.; Benson, B. A.; Vikhlinin, A.; Aird, K. A.; Allen, S. W.; Bautz, M.; Bayliss, M.; Bleem, L. E.; Bocquet, S.; Brodwin, M.; Carlstrom, J. E.; Chang, C. L.; Cho, H. M.; Clocchiatti, A.; Crawford, T. M.; Crites, A. T.; de Haan, T.; Dobbs, M. A.; Foley, R. J.; Forman, W. R.; George, E. M.; Gladders, M. D.; Gonzalez, A. H.; Halverson, N. W.; Hlavacek-Larrondo, J.; Holder, G. P.; Holzapfel, W. L.; Hrubes, J. D.; Jones, C.; Keisler, R.; Knox, L.; Lee, A. T.; Leitch, E. M.; Liu, J.; Lueker, M.; Luong-Van, D.; Mantz, A.; Marrone, D. P.; McMahon, J. J.; Meyer, S. S.; Miller, E. D.; Mocanu, L.; Mohr, J. J.; Murray, S. S.; Padin, S.; Pryke, C.; Reichardt, C. L.; Rest, A.; Ruhl, J. E.; Saliwanchik, B. R.; Saro, A.; Sayre, J. T.; Schaffer, K. K.; Shirokoff, E.; Spieler, H. G.; Stalder, B.; Stanford, S. A.; Staniszewski, Z.; Stark, A. A.; Story, K. T.; Stubbs, C. W.; Vanderlinde, K.; Vieira, J. D.; Williamson, R.; Zahn, O.; Zenteno, A.

    2014-09-24

    We present the results of an X-ray analysis of 80 galaxy clusters selected in the 2500 deg(2) South Pole Telescope survey and observed with the Chandra X-ray Observatory. We divide the full sample into subsamples of ~20 clusters based on redshift and central density, performing a joint X-ray spectral fit to all clusters in a subsample simultaneously, assuming self-similarity of the temperature profile. This approach allows us to constrain the shape of the temperature profile over 0 < r < 1.5R (500), which would be impossible on a per-cluster basis, since the observations of individual clusters have, on average, 2000 X-ray counts. The results presented here represent the first constraints on the evolution of the average temperature profile from z = 0 to z = 1.2. We find that high-z (0.6 < z < 1.2) clusters are slightly (~30%) cooler both in the inner (r < 0.1R (500)) and outer (r > R (500)) regions than their low-z (0.3 < z < 0.6) counterparts. Combining the average temperature profile with measured gas density profiles from our earlier work, we infer the average pressure and entropy profiles for each subsample. Confirming earlier results from this data set, we find an absence of strong cool cores at high z, manifested in this analysis as a significantly lower observed pressure in the central 0.1R (500) of the high-z cool-core subset of clusters compared to the low-z cool-core subset. Overall, our observed pressure profiles agree well with earlier lower-redshift measurements, suggesting minimal redshift evolution in the pressure profile outside of the core. We find no measurable redshift evolution in the entropy profile at r lsim 0.7R (500)—this may reflect a long-standing balance between cooling and feedback over long timescales and large physical scales. We observe a slight flattening of the entropy profile at r gsim R (500) in our high-z subsample. This flattening is consistent with a temperature bias due to the enhanced (~3×) rate at which group-mass (~2

  3. Chemical composition profiles during alkaline flooding at different temperatures and extended residence times

    Energy Technology Data Exchange (ETDEWEB)

    Aflaki, R.; Handy, L.L.

    1992-12-01

    The objective of this work was to investigate whether or not caustic sweeps the major portion of the reservoir efficiently during an alkaline flood process. It was also the objective of this work to study the state of final equilibrium during a caustic flood through determination of the pH and chemical composition profiles along the porous medium. For this purpose, a long porous medium which provided extended residence times was required. It was necessary to set up the porous medium such that the changes in the pH and chemical composition of the solution could be monitored. Four Berea sandstone cores (8 in. length and1 in. diameter) placed in series provided the desired length and the opportunity for sampling in-between cores. This enabled establishment of pH and chemical composition profiles. The experiments were run at, temperatures up.to 180{degrees}C, and the flow rates varied from 4.8 to 0.2 ft/day. The samples were analyzed for pH and for Si and Al concentrations.The results show that caustic consumption is insignificant for temperatures up to 100{degrees}C. Above 100{degrees}C consumption increases and is accompanied by a significant decrease in pH. The sharp decline in pH also coincides with a sharp decline in concentration of silica in solution. The results also show that alumina is removed from the solution and solubility of alumina ultimately reaches zero. Sharp silica and pH declines take place even in the absence of any alumina in solution. As a result, removal of silica from solution is attributed to the irreversible caustic/rock interaction. This interaction is in the form of chemisorption reactions in which silica is adsorbed onto the rock surface consuming hydroxyl ion. Once these reactions were satisfied, caustic breakthrough occurs at a high pH. However, significant pore volumes of caustic must be injected for completion of the chemisorption.

  4. Chemical composition profiles during alkaline flooding at different temperatures and extended residence times

    Energy Technology Data Exchange (ETDEWEB)

    Aflaki, R.; Handy, L.L.

    1992-12-01

    The objective of this work was to investigate whether or not caustic sweeps the major portion of the reservoir efficiently during an alkaline flood process. It was also the objective of this work to study the state of final equilibrium during a caustic flood through determination of the pH and chemical composition profiles along the porous medium. For this purpose, a long porous medium which provided extended residence times was required. It was necessary to set up the porous medium such that the changes in the pH and chemical composition of the solution could be monitored. Four Berea sandstone cores (8 in. length and1 in. diameter) placed in series provided the desired length and the opportunity for sampling in-between cores. This enabled establishment of pH and chemical composition profiles. The experiments were run at, temperatures up.to 180[degrees]C, and the flow rates varied from 4.8 to 0.2 ft/day. The samples were analyzed for pH and for Si and Al concentrations.The results show that caustic consumption is insignificant for temperatures up to 100[degrees]C. Above 100[degrees]C consumption increases and is accompanied by a significant decrease in pH. The sharp decline in pH also coincides with a sharp decline in concentration of silica in solution. The results also show that alumina is removed from the solution and solubility of alumina ultimately reaches zero. Sharp silica and pH declines take place even in the absence of any alumina in solution. As a result, removal of silica from solution is attributed to the irreversible caustic/rock interaction. This interaction is in the form of chemisorption reactions in which silica is adsorbed onto the rock surface consuming hydroxyl ion. Once these reactions were satisfied, caustic breakthrough occurs at a high pH. However, significant pore volumes of caustic must be injected for completion of the chemisorption.

  5. An energy stable evolution method for simulating two-phase equilibria of multi-component fluids at constant moles, volume and temperature

    KAUST Repository

    Kou, Jisheng

    2016-02-25

    In this paper, we propose an energy-stable evolution method for the calculation of the phase equilibria under given volume, temperature, and moles (VT-flash). An evolution model for describing the dynamics of two-phase fluid system is based on Fick’s law of diffusion for multi-component fluids and the Peng-Robinson equation of state. The mobility is obtained from diffusion coefficients by relating the gradient of chemical potential to the gradient of molar density. The evolution equation for moles of each component is derived using the discretization of diffusion equations, while the volume evolution equation is constructed based on the mechanical mechanism and the Peng-Robinson equation of state. It is proven that the proposed evolution system can well model the VT-flash problem, and moreover, it possesses the property of total energy decay. By using the Euler time scheme to discretize this evolution system, we develop an energy stable algorithm with an adaptive choice strategy of time steps, which allows us to calculate the suitable time step size to guarantee the physical properties of moles and volumes, including positivity, maximum limits, and correct definition of the Helmhotz free energy function. The proposed evolution method is also proven to be energy-stable under the proposed time step choice. Numerical examples are tested to demonstrate efficiency and robustness of the proposed method.

  6. Characterization of Temperature Profiles in Skin and Transdermal Delivery System When Exposed to Temperature Gradients In Vivo and In Vitro.

    Science.gov (United States)

    Zhang, Qian; Murawsky, Michael; LaCount, Terri; Hao, Jinsong; Kasting, Gerald B; Newman, Bryan; Ghosh, Priyanka; Raney, Sam G; Li, S Kevin

    2017-07-01

    Performance of a transdermal delivery system (TDS) can be affected by exposure to elevated temperature, which can lead to unintended safety issues. This study investigated TDS and skin temperatures and their relationship in vivo, characterized the effective thermal resistance of skin, and identified the in vitro diffusion cell conditions that would correlate with in vivo observations. Experiments were performed in humans and in Franz diffusion cells with human cadaver skin to record skin and TDS temperatures at room temperature and with exposure to a heat flux. Skin temperatures were regulated with two methods: a heating lamp in vivo and in vitro, or thermostatic control of the receiver chamber in vitro. In vivo basal skin temperatures beneath TDS at different anatomical sites were not statistically different. The maximum tolerable skin surface temperature was approximately 42-43°C in vivo. The temperature difference between skin surface and TDS surface increased with increasing temperature, or with increasing TDS thermal resistance in vivo and in vitro. Based on the effective thermal resistance of skin in vivo and in vitro, the heating lamp method is an adequate in vitro method. However, the in vitro-in vivo correlation of temperature could be affected by the thermal boundary layer in the receiver chamber.

  7. Zinc tin oxide as high-temperature stable recombination layer for mesoscopic perovskite/silicon monolithic tandem solar cells

    KAUST Repository

    Werner, Jérémie

    2016-12-05

    Perovskite/crystalline silicon tandem solar cells have the potential to reach efficiencies beyond those of silicon single-junction record devices. However, the high-temperature process of 500 °C needed for state-of-the-art mesoscopic perovskite cells has, so far, been limiting their implementation in monolithic tandem devices. Here, we demonstrate the applicability of zinc tin oxide as a recombination layer and show its electrical and optical stability at temperatures up to 500 °C. To prove the concept, we fabricate monolithic tandem cells with mesoscopic top cell with up to 16% efficiency. We then investigate the effect of zinc tin oxide layer thickness variation, showing a strong influence on the optical interference pattern within the tandem device. Finally, we discuss the perspective of mesoscopic perovskite cells for high-efficiency monolithic tandem solar cells. © 2016 Author(s)

  8. High-Q energy trapping of temperature-stable shear waves with Lamé cross-sectional polarization in a single crystal silicon waveguide

    Science.gov (United States)

    Tabrizian, R.; Daruwalla, A.; Ayazi, F.

    2016-03-01

    A multi-port electrostatically driven silicon acoustic cavity is implemented that efficiently traps the energy of a temperature-stable eigen-mode with Lamé cross-sectional polarization. Dispersive behavior of propagating and evanescent guided waves in a ⟨100⟩-aligned single crystal silicon waveguide is used to engineer the acoustic energy distribution of a specific shear eigen-mode that is well known for its low temperature sensitivity when implemented in doped single crystal silicon. Such an acoustic energy trapping in the central region of the acoustic cavity geometry and far from substrate obviates the need for narrow tethers that are conventionally used for non-destructive and high quality factor (Q) energy suspension in MEMS resonators; therefore, the acoustically engineered waveguide can simultaneously serve as in-situ self-oven by passing large uniformly distributed DC currents through its body and without any concern about perturbing the mode shape or deforming narrow supports. Such a stable thermo-structural performance besides large turnover temperatures than can be realized in Lamé eigen-modes make this device suitable for implementation of ultra-stable oven-controlled oscillators. 78 MHz prototypes implemented in arsenic-doped single crystal silicon substrates with different resistivity are transduced by in- and out-of-plane narrow-gap capacitive ports, showing high Q of ˜43k. The low resistivity device shows an overall temperature-induced frequency drift of 200 ppm over the range of -20 °C to 80 °C, which is ˜15× smaller compared to overall frequency drift measured for the similar yet high resistivity device in the same temperature range. Furthermore, a frequency tuning of ˜2100 ppm is achieved in high resistivity device by passing 45 mA DC current through its body. Continuous operation of the device under such a self-ovenizing current over 10 days did not induce frequency instability or degradation in Q.

  9. An improvement of the retrieval of temperature and relative humidity profiles from a combination of active and passive remote sensing

    Science.gov (United States)

    Che, Yunfei; Ma, Shuqing; Xing, Fenghua; Li, Siteng; Dai, Yaru

    2018-03-01

    This paper focuses on an improvement of the retrieval of atmospheric temperature and relative humidity profiles through combining active and passive remote sensing. Ground-based microwave radiometer and millimeter-wavelength cloud radar were used to acquire the observations. Cloud base height and cloud thickness determinations from cloud radar were added into the atmospheric profile retrieval process, and a back-propagation neural network method was used as the retrieval tool. Because a substantial amount of data are required to train a neural network, and as microwave radiometer data are insufficient for this purpose, 8 years of radiosonde data from Beijing were used as the database. The monochromatic radiative transfer model was used to calculate the brightness temperatures in the same channels as the microwave radiometer. Parts of the cloud base heights and cloud thicknesses in the training data set were also estimated using the radiosonde data. The accuracy of the results was analyzed through a comparison with L-band sounding radar data and quantified using the mean bias, root-mean-square error (RMSE), and correlation coefficient. The statistical results showed that an inversion with cloud information was the optimal method. Compared with the inversion profiles without cloud information, the RMSE values after adding cloud information reduced to varying degrees for the vast majority of height layers. These reductions were particularly clear in layers with clouds. The maximum reduction in the RMSE for the temperature profile was 2.2 K, while that for the humidity profile was 16%.

  10. Predicting geometry of rectangular and hyperbolic fin profiles with temperature-dependent thermal properties using decomposition and evolutionary methods

    International Nuclear Information System (INIS)

    Bhowmik, Arka; Singla, Rohit K.; Roy, Pranab K.; Prasad, Dilip K.; Das, Ranjan; Repaka, Ramjee

    2013-01-01

    Highlights: • Dimensions of rectangular and hyperbolic fin are predicted for satisfying a given temperature. • Adomian Decomposition Method (ADM) is used to solve the forward problem. • DE in conjunction with ADM is used to solve the inverse problem. • Measurement error up to 5% is found to yield satisfactory reconstructions. - Abstract: This work proposes the application of the Adomian decomposition method (ADM) in conjunction with the differential evolution (DE) for simultaneously estimating the dimensions of a rectangular and hyperbolic profile annular fin in order to satisfy a prescribed temperature requirement. The thermal conductivity and the surface heat transfer are assumed to be temperature-dependent. The required temperature field has been obtained using ADM for cases, involving insulated and convective boundary conditions at the tip. Then, using an inverse scheme based on DE, required fins dimensions satisfying a prescribed temperature field are estimated. Owing to the correlated nature of the unknowns, many feasible solutions have been found to lie within a given range satisfying the given temperature field. This temperature field can offer the flexibility in selecting the designing parameters. The present study is expected to be useful for selecting the dimensions of a rectangular and hyperbolic profile annular fin which can satisfy the given temperature field

  11. Fragile-to-fragile liquid transition at Tg and stable-glass phase nucleation rate maximum at the Kauzmann temperature TK

    International Nuclear Information System (INIS)

    Tournier, Robert F.

    2014-01-01

    An undercooled liquid is unstable. The driving force of the glass transition at T g is a change of the undercooled-liquid Gibbs free energy. The classical Gibbs free energy change for a crystal formation is completed including an enthalpy saving. The crystal growth critical nucleus is used as a probe to observe the Laplace pressure change Δp accompanying the enthalpy change −V m ×Δp at T g where V m is the molar volume. A stable glass–liquid transition model predicts the specific heat jump of fragile liquids at T≤T g , the Kauzmann temperature T K where the liquid entropy excess with regard to crystal goes to zero, the equilibrium enthalpy between T K and T g , the maximum nucleation rate at T K of superclusters containing magic atom numbers, and the equilibrium latent heats at T g and T K . Strong-to-fragile and strong-to-strong liquid transitions at T g are also described and all their thermodynamic parameters are determined from their specific heat jumps. The existence of fragile liquids quenched in the amorphous state, which do not undergo liquid–liquid transition during heating preceding their crystallization, is predicted. Long ageing times leading to the formation at T K of a stable glass composed of superclusters containing up to 147 atom, touching and interpenetrating, are evaluated from nucleation rates. A fragile-to-fragile liquid transition occurs at T g without stable-glass formation while a strong glass is stable after transition

  12. Effects of Growth Temperature and Postharvest Cooling on Anthocyanin Profiles in Juvenile and Mature Brassica oleracea.

    Science.gov (United States)

    Socquet-Juglard, Didier; Bennett, Alexandra A; Manns, David C; Mansfield, Anna Katharine; Robbins, Rebecca J; Collins, Thomas M; Griffiths, Phillip D

    2016-02-24

    The effects of growth temperatures on anthocyanin content and profile were tested on juvenile cabbage and kale plants. The effects of cold storage time were evaluated on both juvenile and mature plants. The anthocyanin content in juvenile plants ranged from 3.82 mg of cyanidin-3,5-diglucoside equivalent (Cy equiv)/g of dry matter (dm) at 25 °C to 10.00 mg of Cy equiv/g of dm at 16 °C, with up to 76% diacylated anthocyanins. Cold storage of juvenile plants decreased the total amount of anthocyanins but increased the diacylated anthocyanin content by 3-5%. In mature plants, cold storage reduced the total anthocyanin content from 22 to 12.23 mg/g after 5 weeks of storage in red cabbage, while the total anthocyanin content increased after 2 weeks of storage from 2.34 to 3.66 mg of Cy equiv/g of dm in kale without having any effect on acylation in either morphotype. The results obtained in this study will be useful for optimizing anthocyanin production.

  13. Correlations Between Topex Altimeter and Temperature Profile Data in the Equatorial Pacific

    Science.gov (United States)

    Adamec, David

    1999-01-01

    Observations of sea-surface heights from satellite altimeters have been a major contributor to monitoring the evolution of the recent major El Nino event. Assimilating altimeter data directly into numerical models only takes advantage of the surface signature provided by the data. However, that surface signature is usually indicative of processes occurring at depth, especially in the equatorial Pacific. In order for assimilation schemes to make maximum use of surface data, it is helpful to have knowledge of how to best extend that data in the vertical to account for that variability. Toward that end, the vertical correlation structure between satellite-observed sea-surface heights and in situ temperature measurements is examined using TOPEX altimeter and TOGA TAO profile data for the period 1993-1998. This time period includes several states of the tropical Pacific, including a perturbed state from 1993-1994, a quiescent state encompassing 1995-1996, and the major ENSO event of 1997-1998. Analyses for each of these periods, as well as the total period will be presented. In addition to analyses at specific depth levels, analyses for particular density surfaces will also be presented.

  14. A new retrieval algorithm for tropospheric temperature, humidity and pressure profiling based on GNSS radio occultation data

    Science.gov (United States)

    Kirchengast, Gottfried; Li, Ying; Scherllin-Pirscher, Barbara; Schwärz, Marc; Schwarz, Jakob; Nielsen, Johannes K.

    2017-04-01

    The GNSS radio occultation (RO) technique is an important remote sensing technique for obtaining thermodynamic profiles of temperature, humidity, and pressure in the Earth's troposphere. However, due to refraction effects of both dry ambient air and water vapor in the troposphere, retrieval of accurate thermodynamic profiles at these lower altitudes is challenging and requires suitable background information in addition to the RO refractivity information. Here we introduce a new moist air retrieval algorithm aiming to improve the quality and robustness of retrieving temperature, humidity and pressure profiles in moist air tropospheric conditions. The new algorithm consists of four steps: (1) use of prescribed specific humidity and its uncertainty to retrieve temperature and its associated uncertainty; (2) use of prescribed temperature and its uncertainty to retrieve specific humidity and its associated uncertainty; (3) use of the previous results to estimate final temperature and specific humidity profiles through optimal estimation; (4) determination of air pressure and density profiles from the results obtained before. The new algorithm does not require elaborated matrix inversions which are otherwise widely used in 1D-Var retrieval algorithms, and it allows a transparent uncertainty propagation, whereby the uncertainties of prescribed variables are dynamically estimated accounting for their spatial and temporal variations. Estimated random uncertainties are calculated by constructing error covariance matrices from co-located ECMWF short-range forecast and corresponding analysis profiles. Systematic uncertainties are estimated by empirical modeling. The influence of regarding or disregarding vertical error correlations is quantified. The new scheme is implemented with static input uncertainty profiles in WEGC's current OPSv5.6 processing system and with full scope in WEGC's next-generation system, the Reference Occultation Processing System (rOPS). Results from

  15. MODIS/Aqua Temperature and Water Vapor Profiles 5-Min L2 Swath 5km V006

    Data.gov (United States)

    National Aeronautics and Space Administration — MODIS/Aqua Temperature and Water Vapor Profiles 5-Min L2 Swath 5km (MYD07_L2). MODIS was launched aboard the Aqua satellite on May 04, 2002 (1:30 pm equator crossing...

  16. Prandtl-Blasius temperature and velocity boundary-layer profiles in turbulent Rayleigh-Bénard convection

    NARCIS (Netherlands)

    Zhou, Quan; Stevens, Richard Johannes Antonius Maria; Sugiyama, K.; Grossmann, Siegfried; Lohse, Detlef; Xia, K.

    2010-01-01

    The shapes of the velocity and temperature profiles near the horizontal conducting plates' centre regions in turbulent Rayleigh–Bénard convection are studied numerically and experimentally over the Rayleigh number range 108 ≲ Ra ≲ 3 × 1011 and the Prandtl number range 0.7 ≲ Pr ≲ 5.4. The results

  17. Magnon, phonon, and electron temperature profiles and the spin Seebeck effect in magnetic insulator/normal metal hybrid structures

    NARCIS (Netherlands)

    Schreier, M.; Kamra, A.; Weiler, M.; Xiao, J.; Bauer, G.E.W.; Gross, R.; Goennenwein, S.T.B.

    2013-01-01

    We calculate the phonon, electron, and magnon temperature profiles in yttrium iron garnet/platinum bilayers by diffusive theory with appropriate boundary conditions, in particular taking into account interfacial thermal resistances. Our calculations show that in thin film hybrids, the interface

  18. Influence of the topography of the surface of the Earth on vertical sounding of the temperature profile

    Directory of Open Access Journals (Sweden)

    A. Pfister

    Full Text Available Atmospheric temperature and humidity fields as well as information on other meteorological parameters are nowadays retrieved from radiance measurements recorded by operational meteorological satellites. Up to now, the inversion procedures used only take into account crude information on the topography of the Earth's surface. However, the applied radiative transfer codes have to consider the Earth's surface as the lower boundary of the atmospheric model and, therefore, need a more precise mean elevation and a classification of the roughness of the Earth's surface. The influence of the topography of the Earth surface on retrieved temperature profiles is studied by using a physico-statistical inversion method. An objective analysis is made of the more precise mean elevation and derivation of roughness parameters using a new high-resolution digital elevation model (DEM with a resolution of 500 m×500 m. By means of a geomorphological process and a newly developed topography rejection test, areas with a high surface roughness are localized and singled out. The influence of topography on the retrieved temperature profiles is illustrated by case studies. Changes are found predominantly in areas with a high variation of topography. Using the new high-resolution DEM and the topography rejection test, the geographical position of the calculated temperature profiles tends to be shifted towards areas with a small vertical variation of topography. The mean elevation determined by the new elevation model better characterizes the area observed. Hence, the temperature profiles can be calculated down to lower atmospheric levels. Furthermore, a guess profile better describing the atmospheric situation is selected by the more precise elevation. In addition, the temperature profiles obtained near the coast are improved considerably by the more precise determination of the surface property `sea' and `land,' respectively. Integration of an

  19. Influence of the topography of the surface of the Earth on vertical sounding of the temperature profile

    Directory of Open Access Journals (Sweden)

    A. Pfister

    1995-03-01

    Full Text Available Atmospheric temperature and humidity fields as well as information on other meteorological parameters are nowadays retrieved from radiance measurements recorded by operational meteorological satellites. Up to now, the inversion procedures used only take into account crude information on the topography of the Earth's surface. However, the applied radiative transfer codes have to consider the Earth's surface as the lower boundary of the atmospheric model and, therefore, need a more precise mean elevation and a classification of the roughness of the Earth's surface. The influence of the topography of the Earth surface on retrieved temperature profiles is studied by using a physico-statistical inversion method. An objective analysis is made of the more precise mean elevation and derivation of roughness parameters using a new high-resolution digital elevation model (DEM with a resolution of 500 m×500 m. By means of a geomorphological process and a newly developed topography rejection test, areas with a high surface roughness are localized and singled out. The influence of topography on the retrieved temperature profiles is illustrated by case studies. Changes are found predominantly in areas with a high variation of topography. Using the new high-resolution DEM and the topography rejection test, the geographical position of the calculated temperature profiles tends to be shifted towards areas with a small vertical variation of topography. The mean elevation determined by the new elevation model better characterizes the area observed. Hence, the temperature profiles can be calculated down to lower atmospheric levels. Furthermore, a guess profile better describing the atmospheric situation is selected by the more precise elevation. In addition, the temperature profiles obtained near the coast are improved considerably by the more precise determination of the surface property `sea' and `land,' respectively. Integration of an independent physical

  20. Thermally Stable and Electrically Conductive, Vertically Aligned Carbon Nanotube/Silicon Infiltrated Composite Structures for High-Temperature Electrodes.

    Science.gov (United States)

    Zou, Qi Ming; Deng, Lei Min; Li, Da Wei; Zhou, Yun Shen; Golgir, Hossein Rabiee; Keramatnejad, Kamran; Fan, Li Sha; Jiang, Lan; Silvain, Jean-Francois; Lu, Yong Feng

    2017-10-25

    Traditional ceramic-based, high-temperature electrode materials (e.g., lanthanum chromate) are severely limited due to their conditional electrical conductivity and poor stability under harsh circumstances. Advanced composite structures based on vertically aligned carbon nanotubes (VACNTs) and high-temperature ceramics are expected to address this grand challenge, in which ceramic serves as a shielding layer protecting the VACNTs from the oxidation and erosive environment, while the VACNTs work as a conductor. However, it is still a great challenge to fabricate VACNT/ceramic composite structures due to the limited diffusion of ceramics inside the VACNT arrays. In this work, we report on the controllable fabrication of infiltrated (and noninfiltrated) VACNT/silicon composite structures via thermal chemical vapor deposition (CVD) [and laser-assisted CVD]. In laser-assisted CVD, low-crystalline silicon (Si) was quickly deposited at the VACNT subsurfaces/surfaces followed by the formation of high-crystalline Si layers, thus resulting in noninfiltrated composite structures. Unlike laser-assisted CVD, thermal CVD activated the precursors inside and outside the VACNTs simultaneously, which realized uniform infiltrated VACNT/Si composite structures. The growth mechanisms for infiltrated and noninfiltrated VACNT/ceramic composites, which we attributed to the different temperature distributions and gas diffusion mechanism in VACNTs, were investigated. More importantly, the as-farbicated composite structures exhibited excellent multifunctional properties, such as excellent antioxidative ability (up to 1100 °C), high thermal stability (up to 1400 °C), good high velocity hot gas erosion resistance, and good electrical conductivity (∼8.95 Sm -1 at 823 K). The work presented here brings a simple, new approach to the fabrication of advanced composite structures for hot electrode applications.

  1. Temperature minima in the average thermal structure of the middle mesosphere (70 - 80 km) from analysis of 40- to 92-km SME global temperature profiles

    Science.gov (United States)

    Clancy, R. Todd; Rusch, David W.; Callan, Michael T.

    1994-01-01

    Global temperatures have been derived for the upper stratosphere and mesosphere from analysis of Solar Mesosphere Explorer (SME) limb radiance profiles. The SME temperature represent fixed local time observations at 1400 - 1500 LT, with partial zonal coverage of 3 - 5 longitudes per day over the 1982-1986 period. These new SME temperatures are compared to the COSPAR International Ionosphere Reference Atmosphere 86 (CIRA 86) climatology (Fleming et al., 1990) as well as stratospheric and mesospheric sounder (SAMS); Barnett and Corney, 1984), National Meteorological Center (NMC); (Gelman et al., 1986), and individual lidar and rocket observations. Significant areas of disagreement between the SME and CIRA 86 mesospheric temperatures are 10 K warmer SME temperatures at altitudes above 80 km. The 1981-1982 SAMS temperatures are in much closer agreement with the SME temperatures between 40 and 75 km. Although much of the SME-CIRA 86 disagreement probably stems from the poor vertical resolution of the observations comprising the CIRA 86 modelm, some portion of the differences may reflect 5- to 10-year temporal variations in mesospheric temperatures. The CIRA 86 climatology is based on 1973-1978 measurements. Relatively large (1 K/yr) 5- to 10-year trends in temperatures as functions of longitude, latitude, and altitude have been observed for both the upper stratosphere (Clancy and Rusch, 1989a) and mesosphere (Clancy and Rusch, 1989b; Hauchecorne et al., 1991). The SME temperatures also exhibit enhanced amplitudes for the semiannual oscillation (SAO) of upper mesospheric temperatures at low latitudes, which are not evident in the CIRA 86 climatology. The so-called mesospheric `temperature inversions' at wintertime midlatitudes, which have been observed by ground-based lidar (Hauschecorne et al., 1987) and rocket in situ measurements (Schmidlin, 1976), are shown to be a climatological aspect of the mesosphere, based on the SME observations.

  2. Mesoporous Mn promoted Co3O4 oxides as an efficient and stable catalyst for low temperature oxidation of CO

    Science.gov (United States)

    Liu, Changxiang; Gong, Lei; Dai, Runying; Lu, Meijuan; Sun, Tingting; Liu, Qian; Huang, Xigen; Huang, Zhong

    2017-09-01

    Mesoporous Mn-doped Co3O4 catalysts were successfully prepared via a dry soft reactive grinding method based on solid state reaction, and their catalytic performances on CO oxidation were evaluated at a high space velocity of 49,500 mL g-1 h-1. A significant promoted effect was observed once the atomic ratios of Mn/(Co+Mn) were lower than 10%, for instance, the temperature for 50% conversion decreased to about -60 °C, showing superior catalytic performance compared to the single metal oxide. Especially, the Mn-promoted Co3O4 catalyst with a Mn/(Co+Mn) molar ratio of 10% could convert 100% CO after 3000 min of time-on-steam without any deactivation at room temperature. As prepared catalysts were characterized by XRD, N2-adsorption/desorption, TEM, H2-TPR, O2-TPD and CO-titration analysis. The significant enhancement of performance for oxidation of CO over Mn-Co-O mixed oxides was associated with the high active oxygen species concentrations formed during the pretreatment in O2 atmosphere.

  3. Temperature profile in apricot tree canopies under the soil and climate conditions of the Romanian Black Sea Coast

    Science.gov (United States)

    Paltineanu, Cristian; Septar, Leinar; Chitu, Emil

    2016-03-01

    The paper describes the temperature profiles determined by thermal imagery in apricot tree canopies under the semi-arid conditions of the Black Sea Coast in a chernozem of Dobrogea Region, Romania. The study analyzes the thermal vertical profile of apricot orchards for three representative cultivars during summertime. Measurements were done when the soil water content (SWC) was at field capacity (FC) within the rooting depth, after intense sprinkler irrigation applications. Canopy temperature was measured during clear sky days at three heights for both sides of the apricot trees, sunlit (south), and shaded (north). For the SWC studied, i.e., FC, canopy height did not induce a significant difference between the temperature of apricot tree leaves (Tc) and the ambient air temperature (Ta) within the entire vertical tree profile, and temperature measurements by thermal imagery can therefore be taken at any height on the tree crown leaves. Differences between sunlit and shaded sides of the canopy were significant. Because of these differences for Tc-Ta among the apricot tree cultivars studied, lower base lines (LBLs) should be determined for each cultivar separately. The use of thermal imagery technique under the conditions of semi-arid coastal areas with low range of vapor pressure deficit could be useful in irrigation scheduling of apricot trees. The paper discusses the implications of the data obtained in the experiment under the conditions of the coastal area of the Black Sea, Romania, and neighboring countries with similar climate, such as Bulgaria and Turkey.

  4. Water temperature profiles for reaches of the Raging River during summer baseflow, King County, western Washington, July 2015

    Science.gov (United States)

    Gendaszek, Andrew S.; Opatz, Chad C.

    2016-03-22

    Re-introducing wood into rivers where it was historically removed is one approach to improving habitat conditions in rivers of the Pacific Northwest. The Raging River drainage basin, which flows into the Snoqualmie River at Fall City, western Washington, was largely logged during the 20th century and wood was removed from its channel. To improve habitat conditions for several species of anadromous salmonids that spawn and rear in the Raging River, King County Department of Transportation placed untethered log jams in a 250-meter reach where wood was historically removed. The U.S. Geological Survey measured longitudinal profiles of near-streambed temperature during summer baseflow along 1,026 meters of channel upstream, downstream, and within the area of wood placements. These measurements were part of an effort by King County to monitor the geomorphic and biological responses to these wood placements. Near-streambed temperatures averaged over about 1-meter intervals were measured with a fiber‑optic distributed temperature sensor every 30 minutes for 7 days between July 7 and 13, 2015. Vertical temperature profiles were measured coincident with the longitudinal temperature profile at four locations at 0 centimeters (cm) (at the streambed), and 35 and 70 cm beneath the streambed to document thermal dynamics of the hyporheic zone and surface water in the study reach.

  5. Temperature profile in apricot tree canopies under the soil and climate conditions of the Romanian Black Sea Coast.

    Science.gov (United States)

    Paltineanu, Cristian; Septar, Leinar; Chitu, Emil

    2016-03-01

    The paper describes the temperature profiles determined by thermal imagery in apricot tree canopies under the semi-arid conditions of the Black Sea Coast in a chernozem of Dobrogea Region, Romania. The study analyzes the thermal vertical profile of apricot orchards for three representative cultivars during summertime. Measurements were done when the soil water content (SWC) was at field capacity (FC) within the rooting depth, after intense sprinkler irrigation applications. Canopy temperature was measured during clear sky days at three heights for both sides of the apricot trees, sunlit (south), and shaded (north). For the SWC studied, i.e., FC, canopy height did not induce a significant difference between the temperature of apricot tree leaves (Tc) and the ambient air temperature (Ta) within the entire vertical tree profile, and temperature measurements by thermal imagery can therefore be taken at any height on the tree crown leaves. Differences between sunlit and shaded sides of the canopy were significant. Because of these differences for Tc-Ta among the apricot tree cultivars studied, lower base lines (LBLs) should be determined for each cultivar separately. The use of thermal imagery technique under the conditions of semi-arid coastal areas with low range of vapor pressure deficit could be useful in irrigation scheduling of apricot trees. The paper discusses the implications of the data obtained in the experiment under the conditions of the coastal area of the Black Sea, Romania, and neighboring countries with similar climate, such as Bulgaria and Turkey.

  6. National Coral Reef Monitoring Program: Shallow Water Conductivity-Temperature-Depth (CTD) Profiles for selected locations across American Samoa in 2015

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Near-shore shallow water Conductivity-Temperature-Depth (CTD) surveys provided vertical profiles of temperature, salinity, and turbidity providing indications for...

  7. National Coral Reef Monitoring Program: Shallow Water Conductivity-Temperature-Depth (CTD) Profiles for selected locations across the Mariana Archipelago in 2014

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Near-shore shallow water Conductivity-Temperature-Depth (CTD) surveys provided vertical profiles of temperature, salinity, and turbidity providing indications for...

  8. National Coral Reef Monitoring Program: Shallow Water Conductivity-Temperature-Depth (CTD) Profiles for selected locations across the Pacific Remote Island Areas since 2014

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Near-shore shallow water Conductivity-Temperature-Depth (CTD) surveys provided vertical profiles of temperature, salinity, and turbidity providing indications for...

  9. National Coral Reef Monitoring Program: Shallow Water Conductivity-Temperature-Depth (CTD) Profiles for selected locations across the Hawaiian Archipelago since 2013

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Near-shore shallow water Conductivity-Temperature-Depth (CTD) surveys provided vertical profiles of temperature, salinity, and turbidity providing indications for...

  10. Heat Transport upon River-Water Infiltration investigated by Fiber-Optic High-Resolution Temperature Profiling

    Science.gov (United States)

    Vogt, T.; Schirmer, M.; Cirpka, O. A.

    2010-12-01

    Infiltrating river water is of high relevance for drinking water supply by river bank filtration as well as for riparian groundwater ecology. Quantifying flow patterns and velocities, however, is hampered by temporal and spatial variations of exchange fluxes. In recent years, heat has become a popular natural tracer to estimate exchange rates between rivers and groundwater. Nevertheless, field investigations are often limited by insufficient sensors spacing or simplifying assumptions such as one-dimensional flow. Our interest lies in a detailed local survey of river water infiltration at a restored river section at the losing river Thur in northeast Switzerland. Here, we measured three high-resolution temperature profiles along an assumed flow path by means of distributed temperature sensing (DTS) using fiber optic cables wrapped around poles. Moreover, piezometers were equipped with standard temperature sensors for a comparison to the DTS data. Diurnal temperature oscillations were tracked in the river bed and the riparian groundwater and analyzed by means of dynamic harmonic regression and subsequent modeling of heat transport with sinusoidal boundary conditions to quantify seepage velocities and thermal diffusivities. Compared to the standard temperature sensors, the DTS data give a higher vertical resolution, facilitating the detection of process- and structure-dependent patterns of the spatiotemporal temperature field. This advantage overcompensates the scatter in the data due to instrument noise. In particular, we could demonstrate the impact of heat conduction through the unsaturated zone on the riparian groundwater by the high resolution temperature profiles.

  11. Profile correction to electron temperature and enhancement factor in soft-x-ray pulse-height-analysis measurements in tokamaks

    International Nuclear Information System (INIS)

    Sesnic, S.; Diesso, M.; Hill, K.; Holland, A.; Pohl, F.

    1988-01-01

    Because soft-x-ray pulse-height-analysis spectra contain chordal information, the electron temperature and the radiation intensity (enhancement factor) measurements do not represent the local values. The correction factors for the electron temperature and the enhancement factor as a function of the temperature and density profile parameters and the energy are obtained. The spectrum distortion due to pulse pileup effects is also evaluated. A set of curves is given from which the distortion of the spectrum can be obtained if the electron temperature, the Be filter thickness, and the electronic parameters of the acquisition system are known. PG 1810,1812 ID 131801CON N X-ray diagnostics TT Profile correction to electron temperature and enhancement factor in soft-x-ray pulse-height-analysis measurements in tokamaks AU S. Sesnic, M. Diesso, K. Hill, and A. Holland LO Princeton University, Plasma Physics Laboratory, P.O. Box 451, Princeton, New Jersey 08543 AU F. Pohl LO Max-Planck Institut fuer Plasmaphysik, 8046-Garching, Federal Republic of Germany SD (Presented on 16 March 1988) AB Because soft-x-ray pulse-height-analysis spectra contain chordal information, the electron temperature and the radiation intensity (enhancement factor) measurements do not represent the local values. The correction factors for the electron temperature and the enhancement factor as a function of the temperature and density profile parameters and the energy are obtained. The spectrum distortion due to pulse pileup effects is also evaluated. A set of curves is given from which the distortion of the spectrum can be obtained if the electron tempe

  12. Temperature variability at Dürres Maar, Germany during the Migration Period and at High Medieval Times, inferred from stable carbon isotopes of Sphagnum cellulose

    Directory of Open Access Journals (Sweden)

    A. Lücke

    2011-09-01

    Full Text Available This paper presents a high resolution reconstruction of local growing season temperature (GST anomalies at Dürres Maar, Germany, spanning the last two millennia. The GST anomalies were derived from a stable carbon isotope time series of cellulose chemically extracted from Sphagnum leaves (δ13Ccellulose separated from a kettle-hole peat deposit of several metres thickness. The temperature reconstruction is based on the Sphagnum δ13Ccellulose/temperature dependency observed in calibration studies. Reconstructed GST anomalies show considerable centennial and decadal scale variability. A cold and presumably wet phase with below-average temperature is reconstructed between the 4th and 7th century AD which is in accordance with the so called European Migration Period, marking the transition from the Late Roman Period to the Early Middle Ages. At High Medieval Times, the amplitude in the reconstructed temperature variability is most likely overestimated; nevertheless, above-average temperatures are obvious during this time span, which are followed by a temperature decrease. On the contrary, a pronounced Late Roman Climate Optimum, often described as similarly warm or even warmer as medieval times, could not be detected. The temperature signal of the Little Ice Age (LIA is not preserved in Dürres Maar due to considerable peat cutting that takes place in the first half of the 19th century. The local GST anomalies show a remarkable agreement to northern hemispheric temperature reconstructions based on tree-ring datasets and are also in accordance with climate reconstructions on the basis of lake sediments, glacier advances and retreats, and historical datasets. Most notably, e.g., during the Early Middle Ages and at High Medieval Times, temperatures were neither low nor high in general. Rather high frequency temperature variability with multiple narrow intervals of below- and above-average temperatures at maximum lasting a few decades are

  13. Measurements of Sheath Temperature Profiles in Bruce LVRF Bundles Under Post-Dryout Heat Transfer Conditions in Freon

    International Nuclear Information System (INIS)

    Guo, Y.; Bullock, D.E.; Pioro, I.L.; Martin, J.

    2006-01-01

    An experimental program has been completed to study the behaviour of sheath wall temperatures in the Bruce Power Station Low Void Reactivity Fuel (shortened hereafter to Bruce LVRF) bundles under post-dryout (PDO) heat-transfer conditions. The experiment was conducted with an electrically heated simulator of a string of nine Bruce LVRF bundles, installed in the MR-3 Freon heat transfer loop at the Chalk River Laboratories (CRL), Atomic Energy of Canada Limited (AECL). The loop used Freon R-134a as a coolant to simulate typical flow conditions in CANDU R nuclear power stations. The simulator had an axially uniform heat flux profile. Two radial heat flux profiles were tested: a fresh Bruce LVRF profile and a fresh natural uranium (NU) profile. For a given set of flow conditions, the channel power was set above the critical power to achieve dryout, while heater-element wall temperatures were recorded at various overpower levels using sliding thermocouples. The maximum experimental overpower achieved was 64%. For the conditions tested, the results showed that initial dryout occurred at an inner-ring element at low flows and an outer-ring element facing internal subchannels at high flows. Dry-patches (regions of dryout) spread with increasing channel power; maximum wall temperatures were observed at the downstream end of the simulator, and immediately upstream of the mid-bundle spacer plane. In general, maximum wall temperatures were observed at the outer-ring elements facing the internal subchannels. The maximum water-equivalent temperature obtained in the test, at an overpower level of 64%, was significantly below the acceptable maximum temperature, indicating that the integrity of the Bruce LVRF will be maintained at PDO conditions. Therefore, the Bruce LVRF exhibits good PDO heat transfer performance. (authors)

  14. Retrieving Atmospheric Temperature and Moisture Profiles from NPP CRIS/ATMS Sensors Using Crimss EDR Algorithm

    Science.gov (United States)

    Liu, X.; Kizer, S.; Barnet, C.; Dvakarla, M.; Zhou, D. K.; Larar, A. M.

    2012-01-01

    The Joint Polar Satellite System (JPSS) is a U.S. National Oceanic and Atmospheric Administration (NOAA) mission in collaboration with the U.S. National Aeronautical Space Administration (NASA) and international partners. The NPP Cross-track Infrared Microwave Sounding Suite (CrIMSS) consists of the infrared (IR) Crosstrack Infrared Sounder (CrIS) and the microwave (MW) Advanced Technology Microwave Sounder (ATMS). The CrIS instrument is hyperspectral interferometer, which measures high spectral and spatial resolution upwelling infrared radiances. The ATMS is a 22-channel radiometer similar to Advanced Microwave Sounding Units (AMSU) A and B. It measures top of atmosphere MW upwelling radiation and provides capability of sounding below clouds. The CrIMSS Environmental Data Record (EDR) algorithm provides three EDRs, namely the atmospheric vertical temperature, moisture and pressure profiles (AVTP, AVMP and AVPP, respectively), with the lower tropospheric AVTP and the AVMP being JPSS Key Performance Parameters (KPPs). The operational CrIMSS EDR an algorithm was originally designed to run on large IBM computers with dedicated data management subsystem (DMS). We have ported the operational code to simple Linux systems by replacing DMS with appropriate interfaces. We also changed the interface of the operational code so that we can read data from both the CrIMSS science code and the operational code and be able to compare lookup tables, parameter files, and output results. The detail of the CrIMSS EDR algorithm is described in reference [1]. We will present results of testing the CrIMSS EDR operational algorithm using proxy data generated from the Infrared Atmospheric Sounding Interferometer (IASI) satellite data and from the NPP CrIS/ATMS data.

  15. A new temperature stable microwave dielectric ceramics: ZnTiNb{sub 2}O{sub 8} sintered at low temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Guo Mei [Department of Electronic Science and Technology, Huazhong University of Science and Technology, Wuhan 430074 (China); Gong Shuping, E-mail: spgong@mail.hust.edu.cn [Department of Electronic Science and Technology, Huazhong University of Science and Technology, Wuhan 430074 (China); Dou Gang; Zhou Dongxiang [Department of Electronic Science and Technology, Huazhong University of Science and Technology, Wuhan 430074 (China)

    2011-05-19

    Highlights: > The sintering temperature of ZnTiNb{sub 2}O{sub 8}-xTiO{sub 2} ceramics with BCB was reduced to 950 deg. C. > The {tau}{sub f} was modified to 0 ppm/deg. C with reasonably good Q x f and {epsilon}{sub r}. > The {epsilon}{sub r} = 38.89, Q x f = 14,500 GHz and {tau}{sub f} = 0 ppm/deg. C were achieved. > It represented very promising candidates as LTCC dielectric materials. - Abstract: The phases, microstructure and microwave dielectric properties of ZnTiNb{sub 2}O{sub 8}-xTiO{sub 2} composite ceramics with different weight percentages of BaCu(B{sub 2}O{sub 5}) additive prepared by solid-state reaction method have been investigated using the X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS). The results showed that the microwave dielectric properties were strongly dependent on densification, grain sizes and crystalline phases. The sintering temperature of ZnTiNb{sub 2}O{sub 8} ceramics was reduced from 1250 deg. C to 950 deg. C by doping BaCu(B{sub 2}O{sub 5}) additive and the temperature coefficient of resonant frequency ({tau}{sub f}) was adjusted from negative value of -52 ppm/deg. C to 0 ppm/deg. C by incorporating TiO{sub 2}. Addition of 2 wt% BaCu(B{sub 2}O{sub 5}) in ZnTiNb{sub 2}O{sub 8}-xTiO{sub 2} (x = 0.8) ceramics sintered at 950 deg. C showed excellent dielectric properties of {epsilon}{sub r} = 38.89, Q x f = 14,500 GHz (f = 4.715 GHz) and {tau}{sub f} = 0 ppm/deg. C, which represented very promising candidates as LTCC dielectrics for LTCC applications.

  16. Improved immunogenicity of individual influenza vaccine components delivered with a novel dissolving microneedle patch stable at room temperature.

    Science.gov (United States)

    Vassilieva, Elena V; Kalluri, Haripriya; McAllister, Devin; Taherbhai, Misha T; Esser, E Stein; Pewin, Winston P; Pulit-Penaloza, Joanna A; Prausnitz, Mark R; Compans, Richard W; Skountzou, Ioanna

    2015-08-01

    Prevention of seasonal influenza epidemics and pandemics relies on widespread vaccination coverage to induce protective immunity. In addition to a good antigenic match with the circulating viruses, the effectiveness of individual strains represented in the trivalent vaccines depends on their immunogenicity. In this study, we evaluated the immunogenicity of H1N1, H3N2, and B seasonal influenza virus vaccine strains delivered individually with a novel dissolving microneedle patch and the stability of this formulation during storage at 25 °C. Our data demonstrate that all strains retained their antigenic activity after incorporation in the dissolving patches as measured by single radial diffusion (SRID) assay and immune responses to vaccination in BALB/c mice. After a single immunization, all three antigens delivered with microneedle patches induced superior neutralizing antibody titers compared to intramuscular immunization. Cutaneous antigen delivery was especially beneficial for the less immunogenic B strain. Mice immunized with dissolving microneedle patches encapsulating influenza A/Brisbane/59/07 (H1N1) vaccine were fully protected against lethal challenge by homologous mouse-adapted influenza virus. All vaccine components retained activity during storage at room temperature for at least 3 months as measured in vitro by SRID assay and in vivo by mouse immunization studies. Our data demonstrate that dissolving microneedle patches are a promising advance for influenza cutaneous vaccination due to improved immune responses using less immunogenic influenza antigens and enhanced stability.

  17. Improved immunogenicity of individual influenza vaccine components delivered with a novel dissolving microneedle patch stable at room temperature

    Science.gov (United States)

    Vassilieva, Elena V.; Kalluri, Haripriya; McAllister, Devin; Taherbhai, Misha T.; Esser, E. Stein; Pewin, Winston P.; Pulit-Penaloza, Joanna A.; Prausnitz, Mark R.; Compans, Richard W.; Skountzou, Ioanna

    2015-01-01

    Prevention of seasonal influenza epidemics and pandemics relies on widespread vaccination coverage to induce protective immunity. In addition to a good antigenic match with the circulating viruses, the effectiveness of individual strains represented in the trivalent vaccines depends on their immunogenicity. In this study we evaluated the immunogenicity of H1N1, H3N2 and B seasonal influenza virus vaccine strains delivered individually with a novel dissolving microneedle patch and the stability of this formulation during storage at 25°C. Our data demonstrate that all strains retained their antigenic activity after incorporation in the dissolving patches as measured by SRID assay and immune responses to vaccination in BALB/c mice. After a single immunization all three antigens delivered with microneedle patches induced superior neutralizing antibody titers compared to intramuscular immunization. Cutaneous antigen delivery was especially beneficial for the less immunogenic B strain. Mice immunized with dissolving microneedle patches encapsulating influenza A/Brisbane/59/07 (H1N1) vaccine were fully protected against lethal challenge by homologous mouse-adapted influenza virus. All vaccine components retained activity during storage at room temperature for at least three months as measured in vitro by SRID assay and in vivo by mouse immunization studies. Our data demonstrate that dissolving microneedle patches are a promising advance for influenza cutaneous vaccination due to improved immune responses using less immunogenic influenza antigens and enhanced stability. PMID:25895053

  18. Tungsten as a Chemically-Stable Electrode Material on Ga-Containing Piezoelectric Substrates Langasite and Catangasite for High-Temperature SAW Devices

    Directory of Open Access Journals (Sweden)

    Gayatri K. Rane

    2016-02-01

    Full Text Available Thin films of tungsten on piezoelectric substrates La3Ga5SiO14 (LGS and Ca3TaGa3Si2O14 (CTGS have been investigated as a potential new electrode material for interdigital transducers for surface acoustic wave-based sensor devices operating at high temperatures up to 800 °C under vacuum conditions. Although LGS is considered to be suitable for high-temperature applications, it undergoes chemical and structural transformation upon vacuum annealing due to diffusion of gallium and oxygen. This can alter the device properties depending on the electrode nature, the annealing temperature, and the duration of the application. Our studies present evidence for the chemical stability of W on these substrates against the diffusion of Ga/O from the substrate into the film, even upon annealing up to 800 °C under vacuum conditions using Auger electron spectroscopy and energy-dispersive X-ray spectroscopy, along with local studies using transmission electron microscopy. Additionally, the use of CTGS as a more stable substrate for such applications is indicated.

  19. Planktic foraminiferal stable-isotopes across the EECO: investigating the coupling between temperature and the exogenic carbon pool (ODP Site 1263, Walvis Ridge)

    Science.gov (United States)

    Schrader, Cindy; Lauretano, Vittoria; Zachos, James C.; Lourens, Lucas J.

    2016-04-01

    The Late Paleocene to Early Eocene warming trend is characterized by a gradual temperature rise of 5-6° C resulting in the Early Eocene Climatic Optimum "EECO". This warming trend was punctuated by several so-called "hyperthermals", which were geologically brief (isotope record of ODP Site 1263 has been presented, which encompasses the peak of the early Eocene "hothouse" (˜49.5 - 54.2 Ma). This record confirms the presence of hyperthermals during and at the termination of the EECO as was previously found for ODP Site 1258. In addition, the record reveals a highly significant linear relationship between ∂18O and ∂13C for these events, similar as for their early Eocene counterparts. This indicates a strong coupling between global warming and the release of isotopically light carbon into the ocean-atmosphere system throughout the EECO. Whilst the coupling between temperature changes and perturbations in the exogenic carbon pool remain stable on short-term time scales, they do not for the long-term trends at ˜52 Ma when a rapid 13C enrichment in carbon data is not accompanied by changes in the oxygen record. It was hypothesized that enhanced carbonate and organic carbon burial rates might be responsible for this shift in average isotopic values during a temporary reduced efficiency of the biological pump. Such a scenario may explain the elevated atmospheric pCO2 as well as increased weathering rates and runoff. To test this hypothesis, we will present our first (preliminary) stable isotopic results of two planktic foraminiferal species derived from the same samples of ODP Site 1263, which portray changes in surface water (Acarinina ssp.) and thermocline waters (Subbotina ssp.).

  20. Accuracy of retrieving temperature and humidity profiles by ground-based microwave radiometry in truly complex terrain

    Science.gov (United States)

    Massaro, G.; Stiperski, I.; Pospichal, B.; Rotach, M. W.

    2015-08-01

    Within the Innsbruck Box project, a ground-based microwave radiometer (RPG-HATPRO) was operated in the Inn Valley (Austria), in very complex terrain, between September 2012 and May 2013 to obtain temperature and humidity vertical profiles of the full troposphere with a specific focus on the valley boundary layer. In order to assess its performance in a deep alpine valley, the profiles obtained by the radiometer with different retrieval algorithms based on different climatologies are compared to local radiosonde data. A retrieval that is improved with respect to the one provided by the manufacturer, based on better resolved data, shows a significantly smaller root mean square error (RMSE), both for the temperature and humidity profiles. The improvement is particularly substantial at the heights close to the mountaintop level and in the upper troposphere. Lower-level inversions, common in an alpine valley, are resolved to a satisfactory degree. On the other hand, upper-level inversions (above 1200 m) still pose a significant challenge for retrieval. For this purpose, specialized retrieval algorithms were developed by classifying the radiosonde climatologies into specialized categories according to different criteria (seasons, daytime, nighttime) and using additional regressors (e.g., measurements from mountain stations). The training and testing on the radiosonde data for these specialized categories suggests that a classification of profiles that reproduces meaningful physical characteristics can yield improved targeted specialized retrievals. A novel and very promising method of improving the profile retrieval in a mountainous region is adding further information in the retrieval, such as the surface temperature at fixed levels along a topographic slope or from nearby mountaintops.

  1. An innovative rotational Raman lidar to measure the temperature profile from the surface to 30 km altitude

    Science.gov (United States)

    Hauchecorne, Alain; Keckhut, Philippe; Mariscal, Jean-François; d'Almeida, Eric; Dahoo, Pierre-Richard; Porteneuve, Jacques

    2016-06-01

    A concept of innovative rotational Raman lidar with daylight measurement capability is proposed to measure the vertical profile of temperature from the ground to the middle stratosphere. The optical filtering is made using a Fabry-Pérot Interferometer with line spacing equal to the line spacing of the Raman spectrum. The detection is made using a linear PMT array operated in photon counting mode. We plan to build a prototype and to test it at the Haute-Provence Observatory lidar facility. to achieve a time resolution permitting the observation of small-scale atmospheric processes playing a role in the troposphere-stratosphere interaction as gravity waves. If successful, this project will open the possibility to consider a Raman space lidar for the global observation of atmospheric temperature profiles.

  2. An innovative rotational Raman lidar to measure the temperature profile from the surface to 30 km altitude

    Directory of Open Access Journals (Sweden)

    Hauchecorne Alain

    2016-01-01

    Full Text Available A concept of innovative rotational Raman lidar with daylight measurement capability is proposed to measure the vertical profile of temperature from the ground to the middle stratosphere. The optical filtering is made using a Fabry-Pérot Interferometer with line spacing equal to the line spacing of the Raman spectrum. The detection is made using a linear PMT array operated in photon counting mode. We plan to build a prototype and to test it at the Haute-Provence Observatory lidar facility. to achieve a time resolution permitting the observation of small-scale atmospheric processes playing a role in the troposphere-stratosphere interaction as gravity waves. If successful, this project will open the possibility to consider a Raman space lidar for the global observation of atmospheric temperature profiles.

  3. Validation and statistical analysis of temperature, humidity profiles and Integrated Water Vapor (IWV) from microwave measurements over Granada (Spain)

    Science.gov (United States)

    Bedoya, Andres; Navas-Guzmán, Francisco; Guerrero-Rascado, Juan Luis; Alados-Arboledas, Lucas

    2017-04-01

    Profiles of meteorological variables such as temperature, relative humidity and integrated water vapor derived from a ground-based microwave radiometer (MWR, RPG-HATPRO) are continuously monitored since 2012 at Granada station (Southeastern Spain). During this period up to 210 collocated meteorological balloons, equipped with a radiosonde DFM-09 (GRAWMET), were launched. This study is carried out with a twofold goal. On one hand, a validation of the MWR products such as temperature and water vapor mixing ratio profiles and the IWV from MWR is carried out comparing with radiosonde measurements. The behavior of MWR retrievals under clear and cloudy conditions and for special situations such as inversions has been analyzed. On the other hand, the whole period with continuous measurements is used for a statistical evaluation of the meteorological variables derived from MWR in order to thermodynamically characterize the atmosphere over Granada.

  4. Analysis on atmospheric pressure, temperature, and wind speed profiles during total solar eclipse 9 March 2016 using time series clustering

    Science.gov (United States)

    Septem Riza, Lala; Wihardi, Yaya; Nurdin, Enjang Ali; Dwi Ardi, Nanang; Puji Asmoro, Cahyo; Wijaya, Agus Fany Chandra; Aria Utama, Judhistira; Bayu Dani Nandiyanto, Asep

    2016-11-01

    Air temperature, pressure, and wind speed measurements on the surface taken during the Total Solar Eclipse (TSE) of March 9, 2016, are made. They were taken in Terentang Beach, Bangka Island, Indonesia. In this paper, we propose to analyze them by using time series clustering. The following steps are conducted: data collecting, splitting, smoothing, distance calculation, and clustering. The final results show cluster memberships of the three parameters on 3 time frames: one day before, the TSE day, and one day after. After doing some simulations, it can be seen that the profiles of temperature and pressure on the TSE day are on the same cluster while the wind-speed profile on the TSE day is the same as on the one day after.

  5. Measurement of temperature profiles in process-applications using fibre-optical methods; Prozessgeeignete Temperaturprofilmessungen mit faseroptischen Methoden

    Energy Technology Data Exchange (ETDEWEB)

    Seefeld, P. [Endress und Hauser Wetzer GmbH und Co.KG, Nesselwang (Germany)

    2008-07-01

    Fibre-optical temperature measuring methods are offering an approach to detect temperature profiles. According to the NAMUR-Technology-Roadmap the detection of temperature profiles is representing an increased benefit. Intrinsic fibre-optical temperature measuring techniques are presented, known as OTDRmethod (Optical tine domain reflectometry) facilitating a distributed temperature measurement method that allows a resolution in the range of decimetres. For the purpose of such applications a suitable photoncounting device comprises mechanical robust fibre-optical components, 3 db Coupler, referenced Laser- Diode, Y-Coupler with integrated band-filter and APD (Avalanche Diode) used in a detection module. A VHDL-coded FBGA-board provides a basic control-device for - a Laser-Driver to generate adjustable exiting-pulses in the range of nanoseconds at rates up to 100 kHz. - a Photon-Counting module with a minimum opening width in the range of one nanosecond - that permits the co-addition of the photon-counts derived from the spectral resolved Stokes and Anti-Stokes band. (orig.)

  6. Spectroscopic measurements of the ion temperature profile in front of a limiter in TEXTOR-94

    Science.gov (United States)

    Huber, A.; Pospieszczyk, A.; Unterberg, B.; Brix, M.; Mertens, Ph; Philipps, V.; Schweer, B.

    2000-05-01

    Ion temperatures have been measured in front of a limiter in TEXTOR-94 under various plasma conditions by means of the Doppler broadening of the C5+ line (λ = 529 nm), which is excited by charge exchange processes with hydrogen (deuterium) atoms recycled at the limiter surface. The ion temperatures have been compared with electron temperatures measured by atomic beam techniques. It has been found that the ion temperatures are considerably larger than those of the electrons. In the scrape-off layer (SOL) the ratio between the ion and electron temperatures (Ti/Te) can reach values of up to three at low plasma densities, but this ratio decreases with increasing density. The SOL e-folding length of the ion temperature is much larger than that of the electron temperature. The influence of the test limiter position rL on the ion temperature measurements has been investigated but found to be of no significant importance.

  7. Biologically relevant physical measurements in the ice-free valleys of southern Victoria Land: soil temperature profiles and ultraviolet radiation

    Science.gov (United States)

    Nienow, J. A.; Meyer, M. A.; Friedmann, E. I. (Principal Investigator)

    1986-01-01

    As part of the ongoing comprehensive study of the cryptoendolithic microbial community in the ice-free valleys of southern Victoria Land, thermal properties of the soil and the ultraviolet radiation regime were measured. Although soil temperature profiles have been measured in the ice-free valleys (e.g., Cameron et al. 1970; Cameron 1972), these are the first such data from higher elevations. This is apparently the first time the ultraviolet radiation regime has been measured in the Antarctic.

  8. Mixed convective-dynamic roll vortices and their effects on initial wind and temperature profiles

    Science.gov (United States)

    Haack, Tracy; Shirer, Hampton N.

    1992-01-01

    A new nonlinear 14-coefficient spectral model of two-dimensional shallow Boussinesq flow is developed and used to investigate the onset and development of both dynamically and convectively forced boundary-layer rolls. The model is developed to accept arbitrary basic-state wind profiles as dynamic forcing, using an Ekman profile to provide a means for easy comparison with other studies. The results are qualitatively compared with those of previous theoretical and observational investigations. The rolls are shown to significantly alter the initial wind profile in the sense found by Faller and Kaylor (1967) and Brown (1970), but via a mechanism independent of the Coriolis force.

  9. High Temperature- and High Pressure-Processed Garlic Improves Lipid Profiles in Rats Fed High Cholesterol Diets

    Science.gov (United States)

    Sohn, Chan Wok; Kim, Hyunae; You, Bo Ram; Kim, Min Jee; Kim, Hyo Jin; Lee, Ji Yeon; Sok, Dai-Eun; Kim, Jin Hee; Lee, Kun Jong

    2012-01-01

    Abstract Garlic protects against degenerative diseases such as hyperlipidemia and cardiovascular diseases. However, raw garlic has a strong pungency, which is unpleasant. In this study, we examined the effect of high temperature/high pressure-processed garlic on plasma lipid profiles in rats. Sprague–Dawley rats were fed a normal control diet, a high cholesterol (0.5% cholesterol) diet (HCD) only, or a high cholesterol diet supplemented with 0.5% high temperature/high pressure-processed garlic (HCP) or raw garlic (HCR) for 10 weeks. The body weights of the rats fed the garlic-supplemented diets decreased, mostly because of reduced fat pad weights. Plasma levels of total cholesterol (TC), low-density lipoprotein cholesterol, and triglyceride (TG) in the HCP and HCR groups decreased significantly compared with those in the HCD group. Additionally, fecal TC and TG increased significantly in the HCP and HCR groups. It is notable that no significant differences in plasma or fecal lipid profiles were observed between the HCP and HCR groups. High temperature/high pressure-processed garlic contained a higher amount of S-allyl cysteine than raw garlic (Pgarlic may be useful as a functional food to improve lipid profiles. PMID:22404600

  10. Flow Rates Measurement and Uncertainty Analysis in Multiple-Zone Water-Injection Wells from Fluid Temperature Profiles

    Directory of Open Access Journals (Sweden)

    José E. O. Reges

    2016-07-01

    Full Text Available This work is a contribution to the development of flow sensors in the oil and gas industry. It presents a methodology to measure the flow rates into multiple-zone water-injection wells from fluid temperature profiles and estimate the measurement uncertainty. First, a method to iteratively calculate the zonal flow rates using the Ramey (exponential model was described. Next, this model was linearized to perform an uncertainty analysis. Then, a computer program to calculate the injected flow rates from experimental temperature profiles was developed. In the experimental part, a fluid temperature profile from a dual-zone water-injection well located in the Northeast Brazilian region was collected. Thus, calculated and measured flow rates were compared. The results proved that linearization error is negligible for practical purposes and the relative uncertainty increases as the flow rate decreases. The calculated values from both the Ramey and linear models were very close to the measured flow rates, presenting a difference of only 4.58 m³/d and 2.38 m³/d, respectively. Finally, the measurement uncertainties from the Ramey and linear models were equal to 1.22% and 1.40% (for injection zone 1; 10.47% and 9.88% (for injection zone 2. Therefore, the methodology was successfully validated and all objectives of this work were achieved.

  11. High temperature- and high pressure-processed garlic improves lipid profiles in rats fed high cholesterol diets.

    Science.gov (United States)

    Sohn, Chan Wok; Kim, Hyunae; You, Bo Ram; Kim, Min Jee; Kim, Hyo Jin; Lee, Ji Yeon; Sok, Dai-Eun; Kim, Jin Hee; Lee, Kun Jong; Kim, Mee Ree

    2012-05-01

    Garlic protects against degenerative diseases such as hyperlipidemia and cardiovascular diseases. However, raw garlic has a strong pungency, which is unpleasant. In this study, we examined the effect of high temperature/high pressure-processed garlic on plasma lipid profiles in rats. Sprague-Dawley rats were fed a normal control diet, a high cholesterol (0.5% cholesterol) diet (HCD) only, or a high cholesterol diet supplemented with 0.5% high temperature/high pressure-processed garlic (HCP) or raw garlic (HCR) for 10 weeks. The body weights of the rats fed the garlic-supplemented diets decreased, mostly because of reduced fat pad weights. Plasma levels of total cholesterol (TC), low-density lipoprotein cholesterol, and triglyceride (TG) in the HCP and HCR groups decreased significantly compared with those in the HCD group. Additionally, fecal TC and TG increased significantly in the HCP and HCR groups. It is notable that no significant differences in plasma or fecal lipid profiles were observed between the HCP and HCR groups. High temperature/high pressure-processed garlic contained a higher amount of S-allyl cysteine than raw garlic (Ptemperature/high pressure-processed garlic may be useful as a functional food to improve lipid profiles.

  12. Efficient and stable CH3NH3PbI3-x(SCN)x planar perovskite solar cells fabricated in ambient air with low-temperature process

    Science.gov (United States)

    Zhang, Zongbao; Zhou, Yang; Cai, Yangyang; Liu, Hui; Qin, Qiqi; Lu, Xubing; Gao, Xingsen; Shui, Lingling; Wu, Sujuan; Liu, Jun-Ming

    2018-02-01

    Planar perovskite solar cells (PSCs) based on CH3NH3PbI3-x(SCN)x (SCN: thiocyanate) active layer and low-temperature processed TiO2 films are fabricated by a sequential two-step method in ambient air. Here, alkali thiocyanates (NaSCN, KSCN) are added into Pb(SCN)2 precursor to improve the microstructure of CH3NH3PbI3-x(SCN)x perovskite layers and performance of the as-prepared PSCs. At the optimum concentrations of alkali thiocyanates as additives, the as-prepared NaSCN-modified and KSCN-modified PSCs demonstrate the efficiencies of 16.59% and 15.63% respectively, being much higher than 12.73% of the reference PSCs without additives. This improvement is primarily ascribed to the enhanced electron transport, reduced recombination rates and much improved microstructures with large grain size and low defect density at grain boundaries. Importantly, it is revealed that the modified PSCs at the optimized concentrations of alkali thiocyanates additives exhibit remarkably improved stability than the reference PSCs against humid circumstance, and a continuous exposure to humid air without encapsulation over 45 days only records about 5% degradation of the efficiency. These findings provide a facile approach to fabricate efficient and stable PSCs by low processing temperature in ambient air, both of which are highly preferred for future practical applications of PSCs.

  13. Temperature and density profiles of an MHD switch-on shock

    International Nuclear Information System (INIS)

    Watson-Munro, C.N.; Bighel, L.; Collins, A.R.; Cramer, N.F.; Cross, R.C.

    1975-02-01

    An experimental study of the structure of MHD switch-on shock waves propagating into partially ionized hydrogen and helium plasmas is described. The variation of electron and ion temperatures through the shock front was studied as a function of the level of preionization. When the shock propagates into an almost fully ionized plasma, the electron temperature rises well above the ion temperature due to resistive heating of the electrons. At low preionization levels however, the ion temperature rises above the electron temperature. These results indicate that ion-neutral collisions can play a dominant role in the dissipation of energy in a shock wave. (author)

  14. Impact of water temperature on the growth and fatty acid profiles of juvenile sea cucumber Apostichopus japonicus (Selenka).

    Science.gov (United States)

    Yu, Haibo; Zhang, Cheng; Gao, Qinfeng; Dong, Shuanglin; Ye, Zhi; Tian, Xiangli

    2016-08-01

    The present study determined the changes in the fatty acid (FA) profiles of juvenile sea cucumber Apostichopus japonicus in response to the varied water temperature. Sea cucumbers with similar size (4.02±0.11g) were cultured for 8 weeks at 14°C, 18°C, 22°C and 26°C, respectively. At the end of the experiment, the specific growth rate (SGR) and the profiles of FAs in neutral lipids and phospholipids of the juvenile sea cucumbers cultured at different temperatures were determined. The SGRs of the sea cucumbers cultured at 26°C significantly decreased 46.3% compared to thos cultured at 18°C. Regression analysis showed that the SGR-temperature (T) relationship can be expressed as SGR=-0.0073T(2)+0.255T -1.0231 (R(2)=0.9936) and the highest SGR was predicted at 17.5°C. For the neutral lipids, the sum of saturated FAs (SFAs), monounsaturated FAs (MUFAs) or polyunsaturated FAs (PUFAs) of the sea cucumbers that were cultured at the water temperature from 18°C-26°C did not change significantly, indicating the insensitivity of FA profiles for the neutral lipids of sea cucumbers in response to increasing water temperature. For phospholipids, the sum of PUFAs in the sea cucumbers dramatically decreased with the gradually increased water temperature. The sum of SFAs and MUFAs of sea cucumbers, however, increased with the gradually elevated water temperature. In particular, the contents of highly unsaturated fatty acids (HUFAs), including eicosapentaenoic acid (EPA, 20:5n-3) and docosahexaenoic acid (DHA), in the phospholipids of the sea cucumbers decreased 37.2% and 26.1%, respectively, when the water temperature increased from 14°C to 26°C. In summary, the sea cucumbers A. japonicus can regulate the FA compositions, especially the contents of EPA and DHA, in the phospholipids so as to adapt to varied water temperature. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. Stable isotopes

    International Nuclear Information System (INIS)

    Evans, D.K.

    1986-01-01

    Seventy-five percent of the world's stable isotope supply comes from one producer, Oak Ridge Nuclear Laboratory (ORNL) in the US. Canadian concern is that foreign needs will be met only after domestic needs, thus creating a shortage of stable isotopes in Canada. This article describes the present situation in Canada (availability and cost) of stable isotopes, the isotope enrichment techniques, and related research programs at Chalk River Nuclear Laboratories (CRNL)

  16. The feasibility of retrieving vertical temperature profiles from satellite nadir UV observations: A sensitivity analysis and an inversion experiment with neural network algorithms

    International Nuclear Information System (INIS)

    Sellitto, P.; Del Frate, F.

    2014-01-01

    Atmospheric temperature profiles are inferred from passive satellite instruments, using thermal infrared or microwave observations. Here we investigate on the feasibility of the retrieval of height resolved temperature information in the ultraviolet spectral region. The temperature dependence of the absorption cross sections of ozone in the Huggins band, in particular in the interval 320–325 nm, is exploited. We carried out a sensitivity analysis and demonstrated that a non-negligible information on the temperature profile can be extracted from this small band. Starting from these results, we developed a neural network inversion algorithm, trained and tested with simulated nadir EnviSat-SCIAMACHY ultraviolet observations. The algorithm is able to retrieve the temperature profile with root mean square errors and biases comparable to existing retrieval schemes that use thermal infrared or microwave observations. This demonstrates, for the first time, the feasibility of temperature profiles retrieval from space-borne instruments operating in the ultraviolet. - Highlights: • A sensitivity analysis and an inversion scheme to retrieve temperature profiles from satellite UV observations (320–325 nm). • The exploitation of the temperature dependence of the absorption cross section of ozone in the Huggins band is proposed. • First demonstration of the feasibility of temperature profiles retrieval from satellite UV observations. • RMSEs and biases comparable with more established techniques involving TIR and MW observations

  17. Periodic nanostructures imprinted on high-temperature stable sol–gel films by ultraviolet-based nanoimprint lithography for photovoltaic and photonic applications

    Energy Technology Data Exchange (ETDEWEB)

    Back, Franziska [Schott AG, Research and Technology Development, Hattenbergstraße 10, 55122 Mainz (Germany); Fraunhofer-Institut für Silicatforschung ISC, Neunerplatz 2, 97082 Würzburg (Germany); Bockmeyer, Matthias; Rudigier-Voigt, Eveline [Schott AG, Research and Technology Development, Hattenbergstraße 10, 55122 Mainz (Germany); Löbmann, Peer [Fraunhofer-Institut für Silicatforschung ISC, Neunerplatz 2, 97082 Würzburg (Germany)

    2014-07-01

    Nanostructured sol–gel films with high-temperature stability are used in the area of electronics, photonics or biomimetic materials as light-trapping architectures in solar cells, displays, waveguides or as superhydrophobic surfaces with a lotus effect. In this work, high-temperature stable 2-μm nanostructured surfaces were prepared by ultraviolet-based nanoimprint lithography using an alkoxysilane binder incorporating modified silica nanoparticles. Material densification during thermal curing and microstructural evolution which are destined for a high structural fidelity of nanostructured films were investigated in relation to precursor chemistry, particle morphology and particle content of the imprint resist. The mechanism for densification and shrinkage of the films was clarified and correlated with the structural fidelity to explain the influence of the geometrical design on the optical properties. A high internal coherence of the microstructure of the nanostructured films results in a critical film thickness of > 5 μm. The structured glassy layers with high inorganic content show thermal stability up to 800 °C and have a high structural fidelity > 90% with an axial shrinkage of 16% and a horizontal shrinkage of 1%. This material allows the realization of highly effective light-trapping architectures for polycrystalline silicon thin-film solar cells on glass but also for the preparation of 2D photonic crystals for telecommunication wavelengths. - Highlights: • Fundamental research • Hybrid sol–gel material with high-temperature stability and contour accuracy • Ensuring of cost-efficient and industrially feasible processing • Application in photonic and photovoltaic.

  18. Reconstructing Changes in Deep Ocean Temperature and Global Carbon Cycle during the Early Eocene Warming Trend: High-Resolution Benthic Stable Isotope Records from the SE Atlantic.

    Science.gov (United States)

    Lauretano, V.; Zachos, J. C.; Lourens, L. J.

    2014-12-01

    From the late Paleocene to the early Eocene, Earth's surface temperatures generally rose, resulting in an increase of at least 5°C in the deep ocean and culminating in the Early Eocene Climatic Optimum (EECO). This long-term warming was punctuated by a series of short-lived global warming events known as "hyperthermals", of which the Paleocene-Eocene Thermal Maximum (PETM) represents the most extreme example. At least two other short-term episodes have been identified as hyperthermals: the ETM2 (or Elmo event) at about 53.7 Myr and the ETM3 (or X-event) at about 52.5 Myr. These transient events are marked by prominent carbon isotope excursions (CIEs), recorded in marine and continental sedimentary sequences and driven by fast and massive injections of 13C-depleted carbon into the ocean-atmosphere system. Recently, evidence has indicated the presence of a regular series of hyperthermal events following the peak in temperatures of the EECO. However, continuous records are needed to investigate short- and long- term changes in the climate system throughout the Early Eocene warming trend. Here, we present new high-resolution benthic stable isotope records of the Early Eocene from ODP Site 1263, (Walvis Ridge, SE Atlantic). The carbon and oxygen records document changes in deep-sea temperature and global carbon cycle encompassing the Early Eocene hyperthermal events and the EECO interval. The transition phase to the post-EECO events is distinct by the decoupling of carbon and oxygen isotopes on the long-term scale. Spectral and wavelet analyses suggest the influence of orbital forcing, specifically long and short eccentricity cycles.

  19. Middle and upper atmosphere pressure-temperature profiles and the abundances of CO2 and CO in the upper atmosphere from ATMOS/Spacelab 3 observations

    Science.gov (United States)

    Rinsland, C. P.; Gunson, M. R.; Zander, R.; Lopez-Puertas, M.

    1992-01-01

    An improved method for retrieving pressure-temperature profiles is described and is used to retrieve profiles of the kinetic-temperature and atmospheric-pressure profiles between 20 and 116 km altitudes and the CO2 and CO volume-mixing ratios between 70 and 116 km, using the IR occultation spectra recorded by the Spacelab 3 atmospheric trace molecular spectroscopy (ATMOS) Fourier transform spectrometer between April 29 and May 6, 1985. Profiles are derived for six ATMOS occultations. The CO2 and CO volume-mixing profiles are compared with previous observations and model predictions. Evidence is found for vibrational non-LTE by analyzing the lines of the (nu-2 + nu-3 - nu-2) (C-12)(O-16) band. Results are used for deriving (C-12)(O-16) (010) vibrational temperatures, which are compared with the retrieved kinetic temperatures and the predictions of non-LTE effects by recent models.

  20. Mineralisation of amethyst-bearing geodes in Ametista do Sul (Brazil) from low-temperature sedimentary brines: evidence from monophase liquid inclusions and stable isotopes

    Science.gov (United States)

    Gilg, H. Albert; Krüger, Yves; Taubald, Heinrich; van den Kerkhof, Alfons M.; Frenz, Martin; Morteani, Giulio

    2014-10-01

    Fluid inclusion studies in combination with hydrogen, oxygen and sulphur isotope data provide novel insights into the genesis of giant amethyst-bearing geodes in Early Cretaceous Paraná continental flood basalts at Amestita do Sul, Brazil. Monophase liquid inclusions in colourless quartz, amethyst, calcite, barite and gypsum were analysed by microthermometry after stimulating bubble nucleation using single femtosecond laser pulses. The salinity of the fluid inclusions was determined from ice-melting temperatures and a combination of prograde and retrograde homogenisation temperatures via the density maximum of the aqueous solutions. Four mineralisation stages are distinguished. In stage I, celadonite, chalcedony and pyrite formed under reducing conditions in a thermally stable environment. Low δ34SV-CDT values of pyrite (-25 to -32 ‰) suggest biogenic sulphate reduction by organotrophic bacteria. During the subsequent stages II (amethyst, goethite and anhydrite), III (early subhedral calcite) and IV (barite, late subhedral calcite and gypsum), the oxidation state of the fluid changed towards more oxidising conditions and microbial sulphate reduction ceased. Three distinct modes of fluid salinities around 5.3, 3.4 and 0.3 wt% NaCl-equivalent characterise the mineralisation stages II, III and IV, respectively. The salinity of the stage I fluid is unknown due to lack of fluid inclusions. Variation in homogenisation temperatures and in δ18O values of amethyst show evidence of repeated pulses of ascending hydrothermal fluids of up to 80-90 °C infiltrating a basaltic host rock of less than 45 °C. Colourless quartz and amethyst formed at temperatures between 40 and 80 °C, while the different calcite generations and late gypsum precipitated at temperatures below 45 °C. Calculated oxygen isotope composition of the amethyst-precipitating fluid in combination with δD values of amethyst-hosted fluid inclusions (-59 to -51 ‰) show a significant 18O-shift from the

  1. Mathematical model to predict temperature profile and air–fuel equivalence ratio of a downdraft gasification process

    International Nuclear Information System (INIS)

    Jaojaruek, Kitipong

    2014-01-01

    Highlights: • A mathematical model based on finite computation analysis was developed. • Model covers all zones of gasification process which will be useful to improve gasifier design. • Model can predict temperature profile, feedstock consumption rate and reaction equivalent ratio (ϕ). • Model-predicted parameters fitted well with experimental values. - Abstract: A mathematical model for the entire length of a downdraft gasifier was developed using thermochemical principles to derive energy and mass conversion equations. Analysis of heat transfer (conduction, convection and radiation) and chemical kinetic technique were applied to predict the temperature profile, feedstock consumption rate (FCR) and reaction equivalence ratio (RER). The model will be useful for designing gasifiers, estimating output gas composition and gas production rate (GPR). Implicit finite difference method solved the equations on the considered reactor length (50 cm) and diameter (20 cm). Conversion criteria for calculation of temperature and feedstock consumption rate were 1 × 10 −6 °C and 1 × 10 −6 kg/h, respectively. Experimental validation showed that model outputs fitted well with experimental data. Maximum deviation between model and experimental data of temperature, FCR and RER were 52 °C at combustion temperature 663 °C, 0.7 kg/h at the rate 8.1 kg/h and 0.03 at the RER 0.42, respectively. Experimental uncertainty of temperature, FCR and RER were 24.4 °C, 0.71 kg/h and 0.04, respectively, on confidence level of 95%

  2. Line profiles of hydrogenic ions from high-temperature and high-density plasmas

    International Nuclear Information System (INIS)

    Hou Qing; Li Jianming

    1991-01-01

    Applying the Hooper's first-order theory, the authors calculate the static micro-electric field distributions in plasmas containing various multiply-charged ions. The influences of the impurity concentrations on the micro electric field distributions and on the Lyman profiles (n→1) from hydrogenic ions are analysed. Based on the optical-thin line profiles, the radiation transfer equation in sphere plasmas with various optical depths is solved. The results confirm that the opacity-broadening of the line profiles has almost no effect on the separation of Lyman β splitted peaks. Such separation is determined by electric field at which the static micro-electric field distribution has a maximum. The separation can be utilized for spatially resolved and temporally resolved density diagnostic of fusion plasmas

  3. Non-stationary temporal characterization of the temperature profile of a soil exposed to frost in south-eastern Canada

    Directory of Open Access Journals (Sweden)

    F. Anctil

    2008-05-01

    Full Text Available The objective of this work was to compare time and frequency fluctuations of air and soil temperatures (2-, 5-, 10-, 20- and 50-cm below the soil surface using the continuous wavelet transform, with a particular emphasis on the daily cycle. The analysis of wavelet power spectra and cross power spectra provided detailed non-stationary accounts with respect to frequencies (or periods and to time of the structure of the data and also of the relationships that exist between time series. For this particular application to the temperature profile of a soil exposed to frost, both the air temperature and the 2-cm depth soil temperature time series exhibited a dominant power peak at 1-d periodicity, prominent from spring to autumn. This feature was gradually damped as it propagated deeper into the soil and was weak for the 20-cm depth. Influence of the incoming solar radiation was also revealed in the wavelet power spectra analysis by a weaker intensity of the 1-d peak. The principal divergence between air and soil temperatures, besides damping, occurred in winter from the latent heat release associated to the freezing of the soil water and the insulation effect of snowpack that cease the dependence of the soil temperature to the air temperature. Attenuation and phase-shifting of the 1-d periodicity could be quantified through scale-averaged power spectra and time-lag estimations. Air temperature variance was only partly transferred to the 2-cm soil temperature time series and much less so to the 20-cm soil depth.

  4. Glass-Transition Temperature Profile Measured in a Wood Cell Wall Using Scanning Thermal Expansion Microscope (SThEM)

    Science.gov (United States)

    Antoniow, J. S.; Maigret, J.-E.; Jensen, C.; Trannoy, N.; Chirtoc, M.; Beaugrand, J.

    2012-11-01

    This study aims to assess the in situ spatial distribution of glass-transition temperatures ( T g) of the main lignocellulosic biopolymers of plant cell walls. Studies are conducted using scanning thermal expansion microscopy to analyze the cross-section of the cell wall of poplar. The surface topography is mapped over a range of probe-tip temperatures to capture the change of thermal expansion on the sample surface versus temperature. For different temperature values chosen between 20 °C and 250 °C, several quantitative mappings were made to show the spatial variation of the thermal expansion. As the glass transition affects the thermal expansion coefficient and elastic modulus considerably, the same data line of each topography image was extracted to identify specific thermal events in their topographic evolution as a function of temperature. In particular, it is shown that the thermal expansion of the contact surface is not uniform across the cell wall and a profile of the glass-transition temperature could thus be evidenced and quantified corresponding to the mobility of lignocellulosic polymers having a role in the organization of the cell wall structures.

  5. Microwave measurements of temperature profiles, integrated water vapour, and liquid water path at Thule Air Base, Greenland.

    Science.gov (United States)

    Pace, Giandomenico; Di Iorio, Tatiana; di Sarra, Alcide; Iaccarino, Antonio; Meloni, Daniela; Mevi, Gabriele; Muscari, Giovanni; Cacciani, Marco

    2017-04-01

    A RPG Humidity And Temperature PROfiler (HATPRO-G2 ) radiometer was installed at Thule Air Base (76.5° N, 68.8° W), Greenland, in June 2016 in the framework of the Study of the water VApour in the polar AtmosPhere (SVAAP) project. The Danish Meteorological Institute started measurements of atmospheric properties at Thule Air Base in early '90s. The Thule High Arctic Atmospheric Observatory (THAAO) has grown in size and observing capabilities during the last three decades through the international effort of United States (NCAR and University of Alaska Fairbanks) and Italian (ENEA, INGV, University of Roma and Firenze) institutions (http://www.thuleatmos-it.it). Within this context, the intensive field campaign of the SVAAP project was aimed at the investigation of the surface radiation budget and took place from 5 to 28 July, 2016. After the summer campaign the HATPRO has continued to operate in order to monitor the annual variability of the temperature profile and integrated water vapour as well as the presence and characteristics of liquid clouds in the Artic environment. The combined use of the HATPRO together with other automatic instruments, such as a new microwave spectrometer (the water Vapour Emission Spectrometer for Polar Atmosphere VESPA-22), upward- and downward-looking pyranometers and pyrgeometers, a zenith-looking pyrometer operating in the 9.6-11.5 µm spectral range, an all sky camera, and a meteorological station, allows to investigate the clouds' physical and optical properties, as well as their impact on the surface radiation budget. This study will present and discuss the first few months of HATPRO observations; the effectiveness of the statistical retrieval used to derive the physical parameters from the HATPRO brightness temperatures will also be investigated through the comparison of the temperature and humidity profiles, and integrated water vapour, with data from radiosondes launched during the summer campaign and in winter time.

  6. OH-equivalent temperatures derived from ACE-FTS and SABER temperature profiles – a comparison with OH*(3-1 temperatures from Maynooth (53.2° N, 6.4° W

    Directory of Open Access Journals (Sweden)

    F. J. Mulligan

    2008-05-01

    Full Text Available OH-equivalent temperatures were derived from all of the temperature profiles retrieved in 2004 and 2005 by the ACE-FTS instrument in a 5 degree band of latitude centred on a ground-based observing station at Maynooth. A globally averaged OH volume emission rate (VER profile obtained from WINDII data was employed as a weighting function to compute the equivalent temperatures. The annual cycle of temperature thus produced was compared with the annual cycle of temperatures recorded at the ground-based station more than a decade earlier from the OH*(3-1 Meinel band. Both data sets showed excellent agreement in the absolute value of the temperature minimum (~162 K and in its time of occurrence in the annual cycle at summer solstice. Away from mid-summer, however, the temperatures diverged and reach a maximum disagreement of more than 20 K in mid-winter. Comparison of the Maynooth ground-based data with the corresponding results from two nearby stations in the same time-period indicated that the Maynooth data are consistent with other ground stations. The temperature difference between the satellite and ground-based datasets in winter was reduced to 14–15 K by lowering the peak altitude of the weighting function to 84 km. An unrealistically low peak altitude would be required, however, to bring temperatures derived from the satellite into agreement with the ground-based data. OH equivalent temperatures derived from the SABER instrument using the same weighting function produced results that agreed well with ACE-FTS. When the OH 1.6 μm VER profile measured by SABER was used as the weighting function, the OH equivalent temperatures increased in winter as expected but the summer temperatures were reduced resulting in an approximately constant offset of 8.6±0.8 K between ground and satellite values with the ground values higher. Variability in both the altitude and width of the OH layer within a discernable seasonal variation were responsible for the

  7. Bradsim-prediction of solute concentration. Temperature and physical property profiles along pulsed plate columns

    International Nuclear Information System (INIS)

    Logsdail, D.H.; Evans, S.F.; Jenkins, J.A.; Smith, I.J.

    1988-01-01

    Dynamic model of the operation of the BRADSIM pulsed plate column is developed. Examples of simulation of the pures process extraction system are given. Profiles of dissolved substances concentrations and profiles of physical properties of liquid along the column are provided. Calculated values are compared with the experimental data, obtained in case of the column 50 mm in diameter, Harwell extractional facility and Sellafield pulsed column 300 mm in diameter for extraction systems uranyl nitrate-nitric acid-20% and 30% TBP in kerosene. 2 refs.; 6 figs

  8. Quantitative amino acid profiling and stable isotopically labeled amino acid tracer enrichment used for in vivo human systemic and tissue kinetics measurements

    DEFF Research Database (Denmark)

    Bornø, Andreas; van Hall, Gerrit

    2014-01-01

    An important area within clinical functional metabolomics is in vivo amino acid metabolism and protein turnover measurements for which accurate amino acid concentrations and stable isotopically labeled amino acid enrichments are mandatory not the least when tissue metabolomics is determined....../ion exchange, derivatized using a phenylisothiocyanate reagent and each amino acid was quantitated with its own stable isotopically labeled internal standard (uniformly labeled-(13)C/(15)N). The method was validated according to general recommendations for chromatographic analytical methods. The calibration...

  9. Room temperature Compton profiles of conduction electrons in α-Ga ...

    Indian Academy of Sciences (India)

    In constructing the secular equation, the temperature-dependent model potential has been evaluated as follows: The contribution to form factor from lattice expansion is eval- uated using the atomic volume Ω appropriate to the temperature in question. The contri- bution from the effect of lattice vibration, on the other hand, ...

  10. Room temperature Compton profiles of conduction electrons in α-Ga ...

    Indian Academy of Sciences (India)

    Room temperature Compton profiles of momentum distribution of conduction electrons in -Ga metal are calculated in band model. For this purpose, the conduction electron wave functions are determined in a temperature-dependent non-local model potential. The profiles calculated along the crystallographic directions, ...

  11. Temperature retrieval from Rayleigh-Brillouin scattering profiles measured in air

    NARCIS (Netherlands)

    Witschas, B.; Ubachs, W.M.G.

    2014-01-01

    In order to investigate the performance of two different algorithms for retrieving temperature from Rayleigh-Brillouin (RB) line shapes, RB scattering measurements have been performed in air at a wavelength of 403 nm, for a temperature range from 257 K to 330 K, and atmospherically relevant

  12. Modeling of temperature profiles in an environmental transmission electron microscope using computational fluid dynamics

    DEFF Research Database (Denmark)

    Mortensen, Peter Mølgaard; Jensen, Anker Degn; Hansen, Thomas Willum

    2015-01-01

    The temperature and velocity field, pressure distribution, and the temperature variation across the sample region inside an environmental transmission electron microscope (ETEM) have been modeled by means of computational fluid dynamics (CFD). Heating the sample area by a furnace type TEM holder...... gives rise to temperature gradients over the sample area. Three major mechanisms have been identified with respect to heat transfer in the sample area: radiation from the grid, conduction in the grid, and conduction in the gas. A parameter sensitivity analysis showed that the sample temperature...... was affected by the conductivity of the gas, the emissivity of the sample grid, and the conductivity of the grid. Ideally the grid should be polished and made from a material with good conductivity, e.g. copper. With hydrogen gas, which has the highest conductivity of the gases studied, the temperature...

  13. Temperature and current profiles from BT and current profilers from DRIFTING PLATFORMS from the SW Atlantic (limit-20 W) and other locations from 01 January 1993 to 31 December 1995 (NODC Accession 9600085)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature and current data from BT cast and current profilers from DRIFTING PLATFORMS from the SW Atlantic (limit-20 W) and other locations. Data was collected by...

  14. Temperature profile data from the SEA-LAND DEFENDER using bottle, CTD, profiling floats, and XBT casts in a world-wide distribution from 01 January 1991 to 31 December 1991 (NODC Accession 0000387)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected from the SEA-LAND DEFENDER from January 1, 1991 to December 31, 1991. Data were submitted by the Institut Francais De...

  15. Temperature profile data from the SEA-LAND DEFENDER using bottle, CTD, profiling floats, and XBT casts in a world-wide distribution from 01 January 1996 to 31 December 1996 (NODC Accession 0000392)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected from the SEA-LAND DEFENDER from January 1, 1996 to December 31, 1996. Data were submitted by Institut Francais De Recherche...

  16. Temperature profile data from the SEA-LAND DEFENDER using bottle, CTD, profiling floats, and XBT casts in a world-wide distribution from 01 January 1994 to 31 December 1994 (NODC Accession 0000390)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected from the SEA-LAND DEFENDER from January 1, 1994 to December 31, 1994. Data were submitted by Institut Francais De Recherche...

  17. Temperature profile data from the SEA-LAND DEFENDER using bottle, CTD, profiling floats, and XBT casts in a world-wide distribution from 01 January 1995 to 31 December 1995 (NODC Accession 0000391)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected from the SEA-LAND DEFENDER from January 1, 1995 to December 31, 1995. Data were submitted by Institut Francais De Recherche...

  18. Temperature profile data from the SEA-LAND DEFENDER using bottle, CTD, profiling floats, and XBT casts in a world-wide distribution from 01 January 1992 to 31 December 1992 (NODC Accession 0000388)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected from the SEA-LAND DEFENDER from January 1, 1992 to December 31, 1992. Data were submitted by Institut Francais De Recherche...

  19. Temperature profile data from the SEA-LAND DEFENDER using bottle, CTD, profiling floats, and XBT casts in a world-wide distribution from 01 January 1997 to 31 December 1997 (NODC Accession 0000393)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected from the SEA-LAND DEFENDER from January 1, 1997 to December 31, 1997. Data were submitted by the Institut Francais De...

  20. Temperature profile data from the SEA-LAND DEFENDER using bottle, CTD, profiling floats, and XBT casts in a world-wide distribution from 01 January 1993 to 31 December 1993 (NODC Accession 0000389)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected from the SEA-LAND DEFENDER from January 1, 1993 to December 31, 1993. Data were submitted by Institut Francais De Recherche...

  1. Modeling of temperature profiles in an environmental transmission electron microscope using computational fluid dynamics

    International Nuclear Information System (INIS)

    Mølgaard Mortensen, Peter; Willum Hansen, Thomas; Birkedal Wagner, Jakob; Degn Jensen, Anker

    2015-01-01

    The temperature and velocity field, pressure distribution, and the temperature variation across the sample region inside an environmental transmission electron microscope (ETEM) have been modeled by means of computational fluid dynamics (CFD). Heating the sample area by a furnace type TEM holder gives rise to temperature gradients over the sample area. Three major mechanisms have been identified with respect to heat transfer in the sample area: radiation from the grid, conduction in the grid, and conduction in the gas. A parameter sensitivity analysis showed that the sample temperature was affected by the conductivity of the gas, the emissivity of the sample grid, and the conductivity of the grid. Ideally the grid should be polished and made from a material with good conductivity, e.g. copper. With hydrogen gas, which has the highest conductivity of the gases studied, the temperature difference over the TEM grid is less than 5 °C, at what must be considered typical conditions, and it is concluded that the conditions on the sample grid in the ETEM can be considered as isothermal during general use. - Highlights: • Computational fluid dynamics used for mapping flow and temperature in ETEM setup. • Temperature gradient across TEM grid in furnace based heating holder very small in ETEM. • Conduction from TEM grid and gas in addition to radiation from TEM grid most important. • Pressure drop in ETEM limited to the pressure limiting apertures

  2. Enzyme activity deviates due to spatial and temporal temperature profiles in commercial microtiter plate readers.

    Science.gov (United States)

    Grosch, Jan-Hendrik; Sieben, Michaela; Lattermann, Clemens; Kauffmann, Kira; Büchs, Jochen; Spieß, Antje C

    2016-03-01

    Microtiter plates (MTP) and automatized techniques are increasingly applied in the field of biotechnology. However, the susceptibility of MTPs to edge effects such as thermal gradients can lead to high variation of measured enzyme activities. In an effort to enhance experimental reliability, to quantify, and to minimize instrument-caused deviations in enzyme kinetics between two MTP-readers, we comprehensively quantified temperature distribution in 96-well MTPs. We demonstrated the robust application of the absorbance dye cresol red as easily applicable temperature indicator in cuvettes and MTPs and determined its accuracy to ±0.16°C. We then quantified temperature distributions in 96-well MTPs revealing temperature deviations over single MTP of up to 2.2°C and different patterns in two commercial devices (BioTek Synergy 4 and Synergy Mx). The obtained liquid temperature was shown to be substantially controlled by evaporation. The temperature-induced enzyme activity variation within MTPs amounted to about 20 %. Activity deviations between MTPs and to those in cuvettes were determined to 40 % due to deviations from the set temperature in MTPs. In conclusion, we propose a better control of experimental conditions in MTPs or alternative experimental systems for reliable determination of kinetic parameters for bioprocess development. Copyright © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  3. In-Situ Acoustic Measurements of Temperature Profile in Extreme Environments

    Energy Technology Data Exchange (ETDEWEB)

    Skliar, Mikhail [Univ. of Utah, Salt Lake City, UT (United States)

    2015-03-31

    A gasifier’s temperature is the primary characteristic that must be monitored to ensure its performance and the longevity of its refractory. One of the key technological challenges impacting the reliability and economics of coal and biomass gasification is the lack of temperature sensors that are capable of providing accurate, reliable, and long-life performance in an extreme gasification environment. This research has proposed, demonstrated, and validated a novel approach that uses a noninvasive ultrasound method that provides real-time temperature distribution monitoring across the refractory, especially the hot face temperature of the refractory. The essential idea of the ultrasound measurements of segmental temperature distribution is to use an ultrasound propagation waveguide across a refractory that has been engineered to contain multiple internal partial reflectors at known locations. When an ultrasound excitation pulse is introduced on the cold side of the refractory, it will be partially reflected from each scatterer in the US propagation path in the refractory wall and returned to the receiver as a train of partial echoes. The temperature in the corresponding segment can be determined based on recorded ultrasonic waveform and experimentally defined relationship between the speed of sound and temperature. The ultrasound measurement method offers a powerful solution to provide continuous real time temperature monitoring for the occasions that conventional thermal, optical and other sensors are infeasible, such as the impossibility of insertion of temperature sensor, harsh environment, unavailable optical path, and more. Our developed ultrasound system consists of an ultrasound engineered waveguide, ultrasound transducer/receiver, and data acquisition, logging, interpretation, and online display system, which is simple to install on the existing units with minimal modification on the gasifier or use with new units. This system has been successfully tested

  4. The electromagnetic force field, fluid flow field and temperature profiles in levitated metal droplets

    Science.gov (United States)

    El-Kaddah, N.; Szekely, J.

    1982-01-01

    A mathematical representation was developed for the electromagnetic force field, the flow field, the temperature field (and for transport controlled kinetics), in a levitation melted metal droplet. The technique of mutual inductances was employed for the calculation of the electromagnetic force field, while the turbulent Navier - Stokes equations and the turbulent convective transport equations were used to represent the fluid flow field, the temperature field and the concentration field. The governing differential equations, written in spherical coordinates, were solved numerically. The computed results were in good agreement with measurements, regarding the lifting force, and the average temperature of the specimen and carburization rates, which were transport controlled.

  5. Effects of moisture and temperature during grain storage on the functional properties and isoflavone profile of soy protein concentrate.

    Science.gov (United States)

    Ziegler, Valmor; Ferreira, Cristiano Dietrich; Hoffmann, Jéssica Fernanda; de Oliveira, Maurício; Elias, Moacir Cardoso

    2018-03-01

    The objective of this study was evaluate the effects of moisture and temperature during grain storage on the functional properties and isoflavone profile of soy protein concentrate. The protein concentrate was extracted from soybeans on the first day of storage and after 12months of storage, at 12 and 15% moisture and at temperatures of 11, 18, 25, and 32°C. The protein concentrate obtained from grains stored at 32°C showed decreased extraction yield (51.6% with 15% of moisture) and protein solubility (24.8% with 15% of moisture) with increased emulsifying capacity (52.2% with 12% of moisture) and foam formation, compared with sample obtained at the start of the storage period. The isoflavone profile showed a decrease in the concentrations of glycosylated, malonyl, and acetyl isoflavones and a corresponding increase in the concentrations of aglycone isoflavones, with the magnitude of these changes increasing with increasing storage temperature and moisture content. Copyright © 2017 Elsevier Ltd. All rights reserved.

  6. Dynamic Analysis of the Temperature and the Concentration Profiles of an Industrial Rotary Kiln Used in Clinker Production

    Directory of Open Access Journals (Sweden)

    DIULIA C.Q. RODRIGUES

    Full Text Available ABSTRACT Cement is one of the most used building materials in the world. The process of cement production involves numerous and complex reactions that occur under different temperatures. Thus, there is great interest in the optimization of cement manufacturing. Clinker production is one of the main steps of cement production and it occurs inside the kiln. In this paper, the dry process of clinker production is analysed in a rotary kiln that operates in counter flow. The main phenomena involved in clinker production is as follows: free residual water evaporation of raw material, decomposition of magnesium carbonate, decarbonation, formation of C3A and C4AF, formation of dicalcium silicate, and formation of tricalcium silicate. The main objective of this study was to propose a mathematical model that realistically describes the temperature profile and the concentration of clinker components in a real rotary kiln. In addition, the influence of different speeds of inlet gas and solids in the system was analysed. The mathematical model is composed of partial differential equations. The model was implemented in Mathcad (available at CCA/UFES and solved using industrial input data. The proposal model is satisfactory to describe the temperature and concentration profiles of a real rotary kiln.

  7. Dynamic Analysis of the Temperature and the Concentration Profiles of an Industrial Rotary Kiln Used in Clinker Production.

    Science.gov (United States)

    Rodrigues, Diulia C Q; Soares, Atílio P; Costa, Esly F; Costa, Andréa O S

    2017-01-01

    Cement is one of the most used building materials in the world. The process of cement production involves numerous and complex reactions that occur under different temperatures. Thus, there is great interest in the optimization of cement manufacturing. Clinker production is one of the main steps of cement production and it occurs inside the kiln. In this paper, the dry process of clinker production is analysed in a rotary kiln that operates in counter flow. The main phenomena involved in clinker production is as follows: free residual water evaporation of raw material, decomposition of magnesium carbonate, decarbonation, formation of C3A and C4AF, formation of dicalcium silicate, and formation of tricalcium silicate. The main objective of this study was to propose a mathematical model that realistically describes the temperature profile and the concentration of clinker components in a real rotary kiln. In addition, the influence of different speeds of inlet gas and solids in the system was analysed. The mathematical model is composed of partial differential equations. The model was implemented in Mathcad (available at CCA/UFES) and solved using industrial input data. The proposal model is satisfactory to describe the temperature and concentration profiles of a real rotary kiln.

  8. Interpretation of ion flux and electron temperature profiles at the JET divertor target during high recycling and detached discharges

    International Nuclear Information System (INIS)

    Monk, R.D.

    1997-01-01

    Detailed experiments have been carried out with the JET Mark I pumped divertor to characterise high recycling and detached plasma regimes. This paper presents new measurements of high resolution divertor ion flux profiles that identify the growth of additional peaks during high recycling discharges. These ion flux profiles are used in conjunction with Dα and neutral flux measurements to examine the physics of divertor detachment and compare against simple analytic models. Finally, problems are highlighted with conventional methods of single and triple probe interpretation under high recycling conditions. By assuming that the single probe behaves as an asymmetric double probe the whole characteristic may be fitted and significantly lower electron temperatures may be derived when the electron to ion saturation current ratio is reduced. The results from the asymmetric double probe fit are shown to be consistent with independent diagnostic measurements. (orig.)

  9. Ion temperature profiles in front of a negative planar electrode studied by a one-dimensional two-fluid model

    Science.gov (United States)

    Gyergyek, T.; Kovačič, J.

    2016-06-01

    Plasma-wall transition is studied by a one-dimensional steady state two-fluid model. Continuity and momentum exchange equations are used for the electrons, while the continuity, momentum exchange, and energy transport equation are used for the ions. Electrons are assumed to be isothermal. The closure of ion equations is made by the assumption that the heat flux is zero. The model equations are solved for potential, ion and electron density, and velocity and ion temperature as independent variables. The model includes coulomb collisions between ions and electrons and charge exchange collisions between ions and neutral atoms of the same species and same mass. The neutral atoms are assumed to be essentially at rest. The model is solved for finite ratio ɛ = /λ D L between the Debye length and λD and ionization length L in the pre-sheath and in the sheath at the same time. Charge exchange collisions heat the ions in the sheath and the pre-sheath. Even a small increase of the frequency of charge exchange collisions causes a substantial increase of ion temperature. Coulomb collisions have negligible effect on ion temperature in the pre-sheath, while in the sheath they cause a small cooling of ions. The increase of ɛ causes the increase of ion temperature. From the ion density and temperature profiles, the polytropic function κ is calculated according to its definition given by Kuhn et al. [Phys. Plasmas 13, 013503 (2006)]. The obtained profiles of κ indicate that the ion flow is isothermal only in a relatively narrow region in the pre-sheath, while close to the sheath edge and in the sheath it is closer to adiabatic. The ion sound velocity is space dependent and exhibits a maximum. This maximum indicates the location of the sheath edge only in the limit ɛ → 0 .

  10. Temperature Profile of the West Antarctic Ice Sheet Divide Deep Borehole, Version 1

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set reports depth versus temperatures in the fluid-filled portion of the West Antarctic Ice Sheet Divide (WAIS–D) deep borehole (70 to 3328 meters depth)....

  11. LBA-ECO CD-10 Temperature Profiles at km 67 Tower Site, Tapajos National Forest

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set contains a single text file which reports temperature measurements at the Para Western (Santarem) - km 67, Primary Forest Tower Site. This site is in...

  12. LBA-ECO CD-10 Temperature Profiles at km 67 Tower Site, Tapajos National Forest

    Data.gov (United States)

    National Aeronautics and Space Administration — ABSTRACT: This data set contains a single text file which reports temperature measurements at the Para Western (Santarem) - km 67, Primary Forest Tower Site. This...

  13. Atmospheric Stability & Turbulence from Temperature Profiles over Sicily During Summer 2002 & 2003 HASI Balloon Campaigns

    Science.gov (United States)

    Colombatti, G.; Ferri, F.; Angrilli, F.; Fulchignoni, M.

    2005-01-01

    Experimental results and interpretation of the temperature measurements data retrieved during the balloon campaigns (in 2002 and in 2003) for testing HASI (Huygens Atmospheric Structure Instrument), launched from the Italian Space Agency Base in Trapani (Sicily), are presented. Both ascending and descending phases are analysed; data reveal interesting features near the tropopause (present in the region between 11km-14km), where temperature cooling can be related to layers with strong winds (2002 flight); in the troposphere a multistratified structure of the temperature field is observed and discussed (particularly in the 2003 flight) Finally, stability and turbulence of the atmosphere are analysed; the buoyancy N2 parameters for both the flights show lowers value respect to standard tropospheric values corresponding to a lower stability of the atmosphere; still there is a higher stability above the tropopause. The energy spectrum of temperature data is consistent with the Kolmogorov theory: the characteristic k(sup -5/3) behaviour is reproduced.

  14. Effect of Plastic Pre-straining on Residual Stress and Composition Profiles in Low-Temperature Surface-Hardened Austenitic Stainless Steel

    DEFF Research Database (Denmark)

    Bottoli, Federico; Christiansen, Thomas Lundin; Winther, Grethe

    2016-01-01

    The present work deals with the evaluation of the residual stress profiles in expanded austenite by applying grazing incidence X-ray diffraction (GI-XRD) combined with successive sublayer removal. Annealed and deformed (εeq=0.5) samples of stable stainless steel EN 1.4369 were nitrided...

  15. Temporal profile of body temperature in acute ischemic stroke: relation to stroke severity and outcome

    Science.gov (United States)

    2012-01-01

    Background Pyrexia after stroke (temperature ≥37.5°C) is associated with poor prognosis, but information on timing of body temperature changes and relationship to stroke severity and subtypes varies. Methods We recruited patients with acute ischemic stroke, measured stroke severity, stroke subtype and recorded four-hourly tympanic (body) temperature readings from admission to 120 hours after stroke. We sought causes of pyrexia and measured functional outcome at 90 days. We systematically summarised all relevant previous studies. Results Amongst 44 patients (21 males, mean age 72 years SD 11) with median National Institute of Health Stroke Score (NIHSS) 7 (range 0–28), 14 had total anterior circulation strokes (TACS). On admission all patients, both TACS and non-TACS, were normothermic (median 36.3°C vs 36.5°C, p=0.382 respectively) at median 4 hours (interquartile range, IQR, 2–8) after stroke; admission temperature and NIHSS were not associated (r2=0.0, p=0.353). Peak temperature, occurring at 35.5 (IQR 19.0 to 53.8) hours after stroke, was higher in TACS (37.7°C) than non-TACS (37.1°C, ptemperatures. Sixteen (36%) patients became pyrexial, in seven (44%) of whom we found no cause other than the stroke. Conclusions Normothermia is usual within the first 4 hours of stroke. Peak temperature occurs at 1.5 to 2 days after stroke, and is related to stroke severity/subtype and more closely associated with poor outcome than admission temperature. Temperature-outcome associations after stroke are complex, but normothermia on admission should not preclude randomisation of patients into trials of therapeutic hypothermia. PMID:23075282

  16. Numerical analysis for temperature profile of the closed house using computational fluid dynamics

    Science.gov (United States)

    Setiadi, Rizki; Munadi, Tauviqirrahman, Mohammad

    2018-03-01

    This study aims to analyze the air temperature distribution in the closed house system for broiler using ABAQUS CFD Model. The obtained data is used for placing the temperature sensor before making the control system for the closed house. The dimesion of the experimental house was 30 m × 12 m × 2 m (length × width × height) which could be occupied by 7.500 broiler. The wall was made from expose mercy brick and curtain, ventilation system used 7 exhaust fan with diameter 1 m and 2 cooling unit, the roof was made from wood, and system used 45 of 7 watt lamp. The results of the analysis show that temperature distribution occurs on temperature 21-33.5°C and still relatively comfortable for broiler at the age of 1-21days. The air temperature distribution near the cooling unit is lower and increases to near the exhaust fan. In addition, the air temperature in the area near the roof is more high than others.

  17. Modelling the evolution of composition-and stress-depth profiles in austenitic stainless steels during low-temperature nitriding

    DEFF Research Database (Denmark)

    Jespersen, Freja Nygaard; Hattel, Jesper Henri; Somers, Marcel A. J.

    2016-01-01

    that accompanies the dissolution of high nitrogen contents in expanded austenite. An intriguing phenomenon during low-temperature nitriding is that the residual stresses evoked by dissolution of nitrogen in the solid state, affect the thermodynamics and the diffusion kinetics of nitrogen dissolution....... In the present paper solid mechanics was combined with thermodynamics and diffusion kinetics to simulate the evolution of composition-depth and stress-depth profiles resulting from nitriding. The model takes into account a composition-dependent diffusion coefficient of nitrogen in expanded austenite, short range...

  18. Temperature profile data from XBT casts by participating vessels in NOAA's Volunteer Observing Ships Program, August - December 2001 (NODC Accession 0000635)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profiles were collected from XBT casts from the ENTERPRISE and other vessels from a world-wide distribution from 01 August 2001 to 03 December 2001. Data...

  19. Temperature profile data from the DONGHAE ILHO and DONUZLAV in a world-wide distribution survey from 01 January 1968 to 11 June 1983 (NODC Accession 0000243)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected from the DONGHAE ILHO and DONUZLAV from January 1, 1968 to June 11, 1993. Additional funding for digitizing historic data was...

  20. Temperature, salinity, nutrient, and ammonia profiles collected by bottle in the Black Sea from 5/5/1955 - 4/16/1989 (NODC Accession 0000131)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Nutrients and temperature profile data were collected using bottle casts from the FIOLENT and other platforms in the Black Sea. Data were collected from 05 May 1955...

  1. Oceanographic profile temperature, salinity, oxygen measurements collected using bottle from multiple platforms in the Azov, Black Seas from 1924-1990 (NODC Accession 0002717)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Oceanographic profile temperature, salinity, oxygen measurements collected using bottle from multiple platforms in the Azov, Black Seas from 1924-1990

  2. Temperature profile data collected from the ALE ANDRO DE HUMBOLDT from 19 September 1971 to 26 September 1971 (NODC Accession 7500942)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected using bottle casts from the ALE ANDRO DE HUMBOLDT in the coastal waters of California from 19 September 1971 to 26 September...

  3. Oceanographic profile temperature, salinity, oxygen and other measurement collected using bottle in the Barents, Kara, Laptev, White, Norwegian Seas from 1900 - 1940 (NODC Accession 0002118)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile and other measurements were collected using bottle casts from the SOTRA in the Barents Sea and other locations from 16 May 1900 to 20 October...

  4. Oceanographic profile temperature, salinity, oxygen and other measurements collected using bottle in the Barents, Kara, Laptev, White, and Norwegian Seas from 1970 through 1975 (NODC Accession 0002125)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Oceanographic profile temperature, salinity, oxygen and other measurements collected using bottle in the Barents, Kara, Laptev, White, and Norwegian Seas from 1970...

  5. Oceanographic profile temperature, salinity, oxygen and other measurements collected using bottle in the Barents, Kara, Laptev, White, Norwegian Seas from 1965 - 1969 (NODC Accession 0002124)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Oceanographic profile temperature, salinity, oxygen and other measurements collected using bottle in the Barents, Kara, Laptev, White, and Norwegian Seas from 1965...

  6. Temperature profile and other data collected using bottle casts in Barents, Kara and other Seas from 03 January 1961 to 30 June 1963 (NODC Accession 0002122)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile and other data were collected using bottle casts from the AISBERG and POLYARNIK in the Kara, Barents, White, Laptev, and Norwegian Sea. Data were...

  7. Temperature profile and other data collected using bottle casts in Barents, Kara and other Seas from 01 January 1963 to 26 December 1964 (NODC Accession 0002123)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile and other data were collected using bottle casts from the AISBERG and other platforms in the Kara, Barents, White, Laptev, and Norwegian Sea....

  8. Oceanographic profile temperature, salinity, oxygen and other measurement collected using bottle in the Barents, Kara, Laptev, White, Norwegian Seas from 1943 - 1950 (NODC Accession 0002119)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile and other measurements were collected using bottle casts in the Barents Sea and other locations from 02 June 1943 to 16 June 1950. Data were...

  9. Temperature profile and water depth data collected from FARRAGUT in the Mediterranean Sea from 20 May 1986 to 30 June 1986 (NODC Accession 8700046)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile and water depth data were collected using BT and XBT from the FARRAGUT in the Mediterranean Sea. Data were collected from 20 May 1986 to 30 June...

  10. Temperature profile data from CTD casts in the Gulf of Alaska from 13 September 1973 to 10 June 1994 (NODC Accession 0000321)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected from the ACONA from September 13, 1973 to June 10, 1974. Data were submitted by the University of Alaska- Fairbanks;...

  11. Temperature profile and nutrients data from bottle casts in the Equatorial Pacific Ocean from 19 April 1971 to 30 March 1994 (NODC Accession 0000225)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile and nutrients data were collected using bottle casts from the ORION and EASTWARD in the Equatorial Pacific Ocean. Data were collected from 19...

  12. Profiles of temperature, salinity, and other measurements from CTD, XBT, and bottle samplers received from the Japan Oceanographic Data Center (NODC Accession 0054093)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Profiles of temperature, salinity, and other measurements received from the Japan Oceanographic Data Center, Hydrographic and Oceanographic Department as a...

  13. Temperature profile and oxygen data from bottle casts in the North Atlantic Ocean from 11 May 1979 to 08 June 1979 (NODC Accession 0000356)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile and oyxgen data were collected from the YAKOV GAKKEL from May 11, 1979 to June 8, 1979. These data were collected using bottle casts in North...

  14. Oceanographic profile temperature, salinity and other measurements collected using bottle and high resolution CTD from the POLARSTERN in the Antarctic and South Atlantic in 1992 (NODC Accession 0000463)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile, nutrients, and other data were collected using plankton net, bottle, and CTD casts from the POLARSTERN in the Southern Oceans. Data were...

  15. Temperature profile data collected using CTD casts from the JAMES CLARK ROSS in the South Atlantic Ocean from 15 November 1994 to 21 November 1994 (NODC Accession 0000873)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected using CTD casts in the South Atlantic Ocean from JAMES CLARK ROSS. Data were collected from 15 November 1994 to 21 November...

  16. Oceanographic profile temperature, salinity, and nutrients measurements collected using bottle, CTD from various platforms in the North West Pacific from 1995-2005 (NODC Accession 0010565)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Physical and Chemical Oceanographic Time Series (Line-P) containing profiles for Nutrients, temperature, salinity near Ocean Station PAPA (50 deg N;145 deg W)....

  17. Temperature profile data from XBT casts in a world wide distribution from multiple platforms from 02 April 2003 to 21 May 2003 (NODC Accession 0001042)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected using XBT casts from SEA-LAND DEFENDER and other platforms in a world wide distribution from 02 April 2003 to 21 May 2003....

  18. Temperature profile data from MBT casts in a world-wide distribution from 23 December 1964 to 19 December 1991 (NODC Accession 0000216)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected using MBT casts from multiple platforms in a world-wide distribution from December 23, 1964 to December 19, 1991. Additonal...

  19. Temperature and salinity profile data collected by NOAA's Navigation Response Team 5 during operations along the northeast US coast, March 2005 - March 2006 (NODC Accession 0002674)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected using CTD casts in the Northwest Atlantic Ocean and the Northeast US Coast from the NAVIGATION RESPONSE TEAM 5 from 03 March...

  20. Temperature and salinity profiles to provide supporting data between MiniBat tows off the Oregon coast, June 2003 (NODC Accession 0002113)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected using CTD casts in the Northeast Pacific Ocean from the NEW HORIZON from 24 June 2003 to 30 June 2003. Data were submitted by...