WorldWideScience

Sample records for stabilized liquid membrane

  1. Stability of supported liquid membranes

    NARCIS (Netherlands)

    Neplenbroek, Antonius Maria

    1989-01-01

    This thesis deals with the stability of supported liquid membranes (SLMs). The use of SLMs, in which an extraction liquid containing a carrier is immobilized in the pores of a microporous support, has recently been introduced as a promising new separation technique. Some advantages ascribed to this

  2. Stabilized ultrathin liquid membranes for gas separations

    International Nuclear Information System (INIS)

    Deetz, D.W.

    1987-01-01

    Although immobilized liquid membranes have the desirable properties of high selectivity and permeability, their practical application to gas phase separations is hindered because of the instability of the liquid phase and the relative thickness of current membranes. The problem of liquid instability, which is due to both liquid volatilization and flooding, can be reduced, or eliminated, by immobilizing the liquid phase in pores small enough to significantly reduce the molar free energy of the solution via the Kelvin effect. The obstacle of membrane thickness can be overcome by selectively immobilizing the liquid phase into the skin of a porous asymmetric membranes

  3. Ionic Liquid Confined in Mesoporous Polymer Membrane with Improved Stability for CO2/N2 Separation

    Directory of Open Access Journals (Sweden)

    Ming Tan

    2017-09-01

    Full Text Available Supported ionic liquid membranes (SILMs have a promising prospect of application in flue gas separation, owing to its high permeability and selectivity of CO2. However, existing SILMs have the disadvantage of poor stability due to the loss of ionic liquid from the large pores of the macroporous support. In this study, a novel SILM with high stability was developed by confining ionic liquid in a mesoporous polymer membrane. First, a mesoporous polymer membrane derived from a soluble, low-molecular-weight phenolic resin precursor was deposited on a porous Al2O3 support, and then 1-ethyl-3-methylimidazolium tetrafluoroborate ([emim][BF4] was immobilized inside mesopores of phenolic resin, forming the SILM under vacuum. Effects of trans-membrane pressure difference on the SILM separation performance were investigated by measuring the permeances of CO2 and N2. The SILM exhibits a high ideal CO2/N2 selectivity of 40, and an actual selectivity of approximately 25 in a mixed gas (50% CO2 and 50% N2 at a trans-membrane pressure difference of 2.5 bar. Compared to [emim][BF4] supported by polyethersulfone membrane with a pore size of around 0.45 μm, the [emim][BF4] confined in a mesoporous polymer membrane exhibits an improved stability, and its separation performance remained stable for 40 h under a trans-membrane pressure difference of 1.5 bar in a mixed gas before the measurement was intentionally stopped.

  4. Stabilized liquid membrane device (SLMD) for the passive, integrative sampling of labile metals in water

    Science.gov (United States)

    Brumbaugh, W.G.; Petty, J.D.; Huckins, J.N.; Manahan, S.E.

    2002-01-01

    A stabilized liquid membrane device (SLMD) is described for potential use as an in situ, passive, integrative sampler for cadmium (Cd), cobalt (Co), copper (Cu), nickel (Ni), lead (Pb), and zinc (Zn) in natural waters. The SLMD (patent pending) consists of a 2.5-cm-wide by 15-cm-long strip of low-density polyethylene (LDPE) layflat tubing containing 1 mL of an equal mixture (v/v) of oleic acid (cis-9-octadecenoic acid) and EMO-8Q (7-[4-ethyl-1-methyloctyl]-8-quinolinol). The reagent mixture continuously diffuses to the exterior surface of the LDPE membrane, and provides for sequestration of several divalent metals for up to several weeks. Depending on sampler configuration, concentration factors of several thousand can be realized for these metal ions after just a few days. In addition to in situ deployment, the SLMD may be useful for laboratory determination of labile metal species in grab samples. Methods for minimizing the effects of water flow on the sampling rate are currently under investigation.

  5. The effect of peptides and ions interacting with an electrically neutral membrane interface on the structure and stability of lipid membranes in the liquid-crystalline phase and in the liquid-ordered phase

    Science.gov (United States)

    Sano, Ryoko; Masum, Shah Md; Tanaka, Tomoki; Yamashita, Yuko; Levadny, Victor; Yamazaki, Masahito

    2005-08-01

    We investigated the effects of a de novo designed peptide, WLFLLKKK (peptide-1) and La3+, which can bind with the electrically neutral lipid membrane interface, on the stability of the phosphatidylcholine (PC) membrane in the Lα phase and that of the liquid-ordered (lo) phase membranes. The results of spacing of the multilamellar vesicle and shape changes of the giant unilamellar vesicle (GUV) indicate that the peptide-1 can be partitioned into the membrane interface in the Lα phase but not into that in the lo phase. La3+ induced shape changes of GUVs of the lo phase membrane, which are the same as those of GUVs in the Lα phase. This indicates that the binding of La3+ induced an increase in the lateral compression pressure of the membrane, which decreased the surface area of the membrane in the lo phase. The difference of the membrane interface between the Lα phase and the lo phase is discussed.

  6. Enantioseparation with liquid membranes

    NARCIS (Netherlands)

    Gössi, Angelo; Riedl, Wolfgang; Schuur, Boelo

    Chiral resolution of racemic products is a challenging and important task in the pharmaceutical, agrochemical, flavor, polymer and fragrances industries. One of the options for these challenging separations is to use liquid membranes. Although liquid membranes have been known for almost four decades

  7. Parallel artificial liquid membrane extraction

    DEFF Research Database (Denmark)

    Gjelstad, Astrid; Rasmussen, Knut Einar; Parmer, Marthe Petrine

    2013-01-01

    This paper reports development of a new approach towards analytical liquid-liquid-liquid membrane extraction termed parallel artificial liquid membrane extraction. A donor plate and acceptor plate create a sandwich, in which each sample (human plasma) and acceptor solution is separated by an arti...... by an artificial liquid membrane. Parallel artificial liquid membrane extraction is a modification of hollow-fiber liquid-phase microextraction, where the hollow fibers are replaced by flat membranes in a 96-well plate format....

  8. Recent development of ionic liquid membranes

    Directory of Open Access Journals (Sweden)

    Junfeng Wang

    2016-04-01

    Full Text Available The interest in ionic liquids (IL is motivated by its unique properties, such as negligible vapor pressure, thermal stability, wide electrochemical stability window, and tunability of properties. ILs have been highlighted as solvents for liquid–liquid extraction and liquid membrane separation. To further expand its application in separation field, the ionic liquid membranes (ILMs and its separation technology have been proposed and developed rapidly. This paper is to give a comprehensive overview on the recent applications of ILMs for the separation of various compounds, including organic compounds, mixed gases, and metal ions. Firstly, ILMs was classified into supported ionic liquid membranes (SILMs and quasi-solidified ionic liquid membranes (QSILMs according to the immobilization method of ILs. Then, preparation methods of ILMs, membrane stability as well as applications of ILMs in the separation of various mixtures were reviewed. Followed this, transport mechanisms of gaseous mixtures and organic compounds were elucidated in order to better understand the separation process of ILMs. This tutorial review intends to not only offer an overview on the development of ILMs but also provide a guide for ILMs preparations and applications. Keywords: Ionic liquid membrane, Supported ionic liquid membrane, Qusai-solidified ionic liquid membrane, Stability, Application

  9. Acquisition of Co metal from spent lithium-ion battery using emulsion liquid membrane technology and emulsion stability test

    Science.gov (United States)

    Yuliusman; Wulandari, P. T.; Amiliana, R. A.; Huda, M.; Kusumadewi, F. A.

    2018-03-01

    Lithium-ion batteries are the most common type to be used as energy source in mobile phone. The amount of lithium-ion battery wastes is approximated by 200 – 500 ton/year. In one lithium-ion battery, there are 5 – 20% of cobalt metal, depend on the manufacturer. One of the way to recover a valuable metal from waste is leaching process then continued with extraction, which is the aim of this study. Spent lithium-ion batteries will be characterized with EDX and AAS, the result will show the amount of cobalt metal with form of LiCoO2 in the cathode. Hydrochloric acid concentration used is 4 M, temperature 80°C, and reaction time 1 hour. This study will discuss the emulsion stability test on emulsion liquid membrane. The purpose of emulsion stability test in this study was to determine optimum concentration of surfactant and extractant to produce a stable emulsion. Surfactant and extractant used were SPAN 80 and Cyanex 272 respectively with both concentrations varied. Membrane and feed phase ratios used in this experiment was 1 : 2. The optimum results of this study were SPAN 80 concentrations of 10% w/v and Cyanex 272 0.7 M.

  10. The effect of peptides and ions interacting with an electrically neutral membrane interface on the structure and stability of lipid membranes in the liquid-crystalline phase and in the liquid-ordered phase

    Energy Technology Data Exchange (ETDEWEB)

    Sano, Ryoko [Department of Physics, Faculty of Science, Shizuoka University, Shizuoka, 422-8529 (Japan); Masum, Shah Md [Material Science, Graduate School of Science and Engineering, Shizuoka University, 422-8529 (Japan); Tanaka, Tomoki [Material Science, Graduate School of Science and Engineering, Shizuoka University, 422-8529 (Japan); Yamashita, Yuko [Department of Physics, Faculty of Science, Shizuoka University, Shizuoka, 422-8529 (Japan); Levadny, Victor [Department of Physics, Faculty of Science, Shizuoka University, Shizuoka, 422-8529 (Japan); Scientific Council for Cybernetics, Russian Academy of Sciences, Vavilov street 34, 333117, Moscow (Russian Federation); Yamazaki, Masahito [Department of Physics, Faculty of Science, Shizuoka University, Shizuoka, 422-8529 (Japan); Material Science, Graduate School of Science and Engineering, Shizuoka University, 422-8529 (Japan)

    2005-08-10

    We investigated the effects of a de novo designed peptide, WLFLLKKK (peptide-1) and La{sup 3+}, which can bind with the electrically neutral lipid membrane interface, on the stability of the phosphatidylcholine (PC) membrane in the L{sub {alpha}} phase and that of the liquid-ordered (lo) phase membranes. The results of spacing of the multilamellar vesicle and shape changes of the giant unilamellar vesicle (GUV) indicate that the peptide-1 can be partitioned into the membrane interface in the L{sub {alpha}} phase but not into that in the lo phase. La{sup 3+} induced shape changes of GUVs of the lo phase membrane, which are the same as those of GUVs in the L{sub {alpha}} phase. This indicates that the binding of La{sup 3+} induced an increase in the lateral compression pressure of the membrane, which decreased the surface area of the membrane in the lo phase. The difference of the membrane interface between the L{sub {alpha}} phase and the lo phase is discussed.

  11. The effect of peptides and ions interacting with an electrically neutral membrane interface on the structure and stability of lipid membranes in the liquid-crystalline phase and in the liquid-ordered phase

    International Nuclear Information System (INIS)

    Sano, Ryoko; Masum, Shah Md; Tanaka, Tomoki; Yamashita, Yuko; Levadny, Victor; Yamazaki, Masahito

    2005-01-01

    We investigated the effects of a de novo designed peptide, WLFLLKKK (peptide-1) and La 3+ , which can bind with the electrically neutral lipid membrane interface, on the stability of the phosphatidylcholine (PC) membrane in the L α phase and that of the liquid-ordered (lo) phase membranes. The results of spacing of the multilamellar vesicle and shape changes of the giant unilamellar vesicle (GUV) indicate that the peptide-1 can be partitioned into the membrane interface in the L α phase but not into that in the lo phase. La 3+ induced shape changes of GUVs of the lo phase membrane, which are the same as those of GUVs in the L α phase. This indicates that the binding of La 3+ induced an increase in the lateral compression pressure of the membrane, which decreased the surface area of the membrane in the lo phase. The difference of the membrane interface between the L α phase and the lo phase is discussed

  12. Fibrous Support Stabilizes Nitrification Performance of a Membrane-Aerated Biofilm: The Effect of Liquid Flow Perturbation

    DEFF Research Database (Denmark)

    Terada, Akihiko; Ito, J; Matsumoto, S

    2009-01-01

    Nitrification stability and biofilm robustness were examined by comparing a fibrous support membrane-aerated biofilm reactor (FS-MABR), where a woven fibrous support was surrounded on a silicone tube, with an MABR. The overall mass transfer coefficient of oxygen for the FS-MABR, assuming no bound......Nitrification stability and biofilm robustness were examined by comparing a fibrous support membrane-aerated biofilm reactor (FS-MABR), where a woven fibrous support was surrounded on a silicone tube, with an MABR. The overall mass transfer coefficient of oxygen for the FS-MABR, assuming...

  13. Fibrous Support Stabilizes Nitrification Performance of a Membrane-Aerated Biofilm: The Effect of Liquid Flow Perturbation

    DEFF Research Database (Denmark)

    Terada, Akihiko; Ito, J; Matsumoto, S

    2009-01-01

    Nitrification stability and biofilm robustness were examined by comparing a fibrous support membrane-aerated biofilm reactor (FS-MABR), where a woven fibrous support was surrounded on a silicone tube, with an MABR. The overall mass transfer coefficient of oxygen for the FS-MABR, assuming no bound...

  14. Supported ionic liquid membrane in membrane reactor

    Science.gov (United States)

    Makertihartha, I. G. B. N.; Zunita, M.; Dharmawijaya, P. T.; Wenten, I. G.

    2017-01-01

    Membrane reactor is a device that integrates membrane based separation and (catalytic) chemical reaction vessel in a single device. Ionic liquids, considered to be a relatively recent magical chemical due to their unique properties, have a large variety of applications in all areas of chemical industries. Moreover, the ionic liquid can be used as membrane separation layer and/or catalytically active site. This paper will review utilization of ionic liquid in membrane reactor related applications especially Fischer-Tropsch, hydrogenation, and dehydrogenation reaction. This paper also reviews about the capability of ionic liquid in equilibrium reaction that produces CO2 product so that the reaction will move towards the product. Water gas shift reaction in ammonia production also direct Dimethyl Ether (DME) synthesis that produces CO2 product will be discussed. Based on a review of numerous articles on supported ionic liquid membrane (SILM) indicate that ionic liquids have the potential to support the process of chemical reaction and separation in a membrane reactor.

  15. Composite hollow fiber gas-liquid membrane contactors for olefin/paraffin separation

    NARCIS (Netherlands)

    Nijmeijer, Dorothea C.; Visser, Tymen; Assen, R.; Wessling, Matthias

    2004-01-01

    Gas¿liquid membrane contactors frequently suffer from undesired wetting of the microporous membrane by the absorption liquid. Stabilization layers at the liquid-side of the microporous membrane potentially prevent this wetting. We apply such stabilized membranes in a membrane contactor using AgNO3

  16. Selective Ion Transporting Polymerized Ionic Liquid Membrane Separator for Enhancing Cycle Stability and Durability in Secondary Zinc-Air Battery Systems.

    Science.gov (United States)

    Hwang, Ho Jung; Chi, Won Seok; Kwon, Ohchan; Lee, Jin Goo; Kim, Jong Hak; Shul, Yong-Gun

    2016-10-05

    Rechargeable secondary zinc-air batteries with superior cyclic stability were developed using commercial polypropylene (PP) membrane coated with polymerized ionic liquid as separators. The anionic exchange polymer was synthesized copolymerizing 1-[(4-ethenylphenyl)methyl]-3-butylimidazolium hydroxide (EBIH) and butyl methacrylate (BMA) monomers by free radical polymerization for both functionality and structural integrity. The ionic liquid induced copolymer was coated on a commercially available PP membrane (Celguard 5550). The coat allows anionic transfer through the separator and minimizes the migration of zincate ions to the cathode compartment, which reduces electrolyte conductivity and may deteriorate catalytic activity by the formation of zinc oxide on the surface of the catalyst layer. Energy dispersive X-ray spectroscopy (EDS) data revealed the copolymer-coated separator showed less zinc element in the cathode, indicating lower zinc crossover through the membrane. Ion coupled plasma optical emission spectroscopy (ICP-OES) analysis confirmed over 96% of zincate ion crossover was reduced. In our charge/discharge setup, the constructed cell with the ionic liquid induced copolymer casted separator exhibited drastically improved durability as the battery life increased more than 281% compared to the pure commercial PP membrane. Electrochemical impedance spectroscopy (EIS) during the cycle process elucidated the premature failure of cells due to the zinc crossover for the untreated cell and revealed a substantial importance must be placed in zincate control.

  17. Composite hollow fiber membranes for organic solvent-based liquid-liquid extraction

    NARCIS (Netherlands)

    He, T.; Bolhuis-Versteeg, Lydia A.M.; Mulder, M.H.V.; Wessling, Matthias

    2004-01-01

    Instability issues of liquid membranes extraction significantly limit its wide application in industry. We report research on the application of a new composite hollow fiber membrane to stabilizing liquid membrane extraction. These type of composite membranes have either a polysulfone (PSf)

  18. Supported liquid membrane battery separators

    Science.gov (United States)

    Pemsler, J. P.; Dempsey, M. D.

    1984-07-01

    The feasibility of using a supported liquid membrane (SLM) as a separator in the nickel-zinc battery was investigated. In particular, SLM separators should prevent zinc dendirte growth from shorting out the cell and might also alleviate capacity loss due to zinc electrode shape changes. A number of ion exchange/solvent modifier systems for incorporation into SLMs were developed under a previous LBL contract. SLMs prepared with hese reagents exhibited resistances in the range of 0.4 to 10 ohm sq cm, selectivity transported hydroxyl ions over zincate ions by a factor of 10 to the 6th power to 10 to the 7th power, and possessed electrochemical and chemical stability in alkaline electrolytes. In order to evaluate these SLM separators under conditions closely resembling a commercial Ni-Zn cell, an accelerated cycle life test was devised using commercial electrodes.

  19. Organosilica Membrane with Ionic Liquid Properties for Separation of Toluene/H₂ Mixture.

    Science.gov (United States)

    Hirota, Yuichiro; Maeda, Yohei; Yamamoto, Yusuke; Miyamoto, Manabu; Nishiyama, Norikazu

    2017-08-03

    In this study, we present a new concept in chemically stabilized ionic liquid membranes: an ionic liquid organosilica (ILOS) membrane, which is an organosilica membrane with ionic liquid-like properties. A silylated ionic liquid was used as a precursor for synthesis. The permselectivity, permeation mechanism, and stability of the membrane in the H₂/toluene binary system were then compared with a supported ionic liquid membrane. The membrane showed a superior separation factor of toluene/H₂ (>17,000) in a binary mixture system based on a solution-diffusion mechanism with improved durability over the supported ionic liquid membrane.

  20. Market liquidity and financial stability.

    OpenAIRE

    Crockett, A.

    2008-01-01

    Stability in financial institutions and in financial markets are closely intertwined. Banks and other financial institutions need liquid markets through which to conduct risk management. And markets need the back-up liquidity lines provided by financial institutions. Market liquidity depends not only on objective, exogenous factors, but also on endogenous market dynamics. Central banks responsible for systemic stability need to consider how far their traditional responsibility for the health ...

  1. Comparative antioxidant capacity, membrane stabilization ...

    African Journals Online (AJOL)

    Comparative antioxidant capacity, membrane stabilization, polyphenol composition and cytotoxicity of the leaf and stem of Cissus multistriata. ... standard anti-inflammatory drug (Indomethacin) used. The extracts are less toxic to the cell (Arthenia salina) with their LC/EC50 higher than that of standard potassium dichromate ...

  2. Comparative antioxidant capacity, membrane stabilization ...

    African Journals Online (AJOL)

    STORAGESEVER

    2008-09-03

    Sep 3, 2008 ... In this present study, a comparative evaluation of the antioxidant capacities, phenol and polyphenol composition, membrane stabilization, and cytotoxicity to brine shrimps (Arthemia salina) of the leaf and stem extracts of Cissus multistriata were carried out. 2,2- Diphenyl-1-picryl hydrazyl (DPPH) radical.

  3. Arsenic Removal by Liquid Membranes

    Directory of Open Access Journals (Sweden)

    Tiziana Marino

    2015-03-01

    Full Text Available Water contamination with harmful arsenic compounds represents one of the most serious calamities of the last two centuries. Natural occurrence of the toxic metal has been revealed recently for 21 countries worldwide; the risk of arsenic intoxication is particularly high in Bangladesh and India but recently also Europe is facing similar problem. Liquid membranes (LMs look like a promising alternative to the existing removal processes, showing numerous advantages in terms of energy consumption, efficiency, selectivity, and operational costs. The development of different LM configurations has been a matter of investigation by several researching groups, especially for the removal of As(III and As(V from aqueous solutions. Most of these LM systems are based on the use of phosphine oxides as carriers, when the metal removal is from sulfuric acid media. Particularly promising for water treatment is the hollow fiber supported liquid membrane (HFSLM configuration, which offers high selectivity, easy transport of the targeted metal ions, large surface area, and non-stop flow process. The choice of organic extractant(s plays an essential role in the efficiency of the arsenic removal. Emulsion liquid membrane (ELM systems have not been extensively investigated so far, although encouraging results have started to appear in the literature. For such LM configuration, the most relevant step toward efficiency is the choice of the surfactant type and its concentration.

  4. Hollow fiber liquid supported membranes

    International Nuclear Information System (INIS)

    Violante, V.

    1987-01-01

    The hollow fiber system are well known and developed in the scientific literature because of their applicability in the process separation units. The authors approach to a mathematical model for a particular hollow fiber system, usin liquid membranes. The model has been developed in order to obtain a suitable tool for a sensitivy analysis and for a scaling-up. This kind of investigation is very usefull from an engineering point of view, to get a spread range of information to build up a pilot plant from the laboratory scale

  5. A study on ion separation through liquid membrane

    International Nuclear Information System (INIS)

    Kang, Young Ho; Kwon, Sun Kil; Joo, Jae Oh; Whang, Sung Chan; Kim, Jung Do; Ann, Hyun Suk

    1991-12-01

    The flux of uranyl nitrate across cellulose acetate was determined using TOPO as a carrier. TOPO particles were physically entrapped in the membrane, which prepared by phase inversion method. The dominating factors were the amount of plasticizer, CTA-TOPO ratio in the membrane, uranium concentration in the feed solution, acidity and the solution temperature. And the transport phenomena of uranyl nitrate across this membrane were microscopically analysed by SEM. The increase of the membrane stability was observed when TOPO was used as a carrier. Another new technology to economically reduce the low-level liquid waste through the membrane is tested in a laboratory scale. (Author)

  6. MECHANISM OF LIQUID MEMBRANES AND APPLICATIONS

    Directory of Open Access Journals (Sweden)

    Filiz Nuran ACAR

    2002-02-01

    Full Text Available It has been considerably studied on the recycling of waste materials in the source besides of wastewater treatment in the last years. It has been important developments on the using of semiconductor membranes in the recycling of toxic materials such as heavy metals, intensifying the environment protection measures especially in the west countries. Wastewater treatment has been achieved with liquid membranes as it has been achieved with polymeric membrane systems such as ultrafiltration, microfiltration, electrodialysis. At the same time, liquid membranes are used for removal of metal ions in hydrometallurgy. Liquid membranes are also used in biotechnology, medical areas and gas separation process.

  7. Ionic Liquid Membranes for Carbon Dioxide Separation

    Energy Technology Data Exchange (ETDEWEB)

    Myers, C.R.; Ilconich, J.B.; Luebke, D.R.; Pennline, H.W.

    2008-07-12

    amine interactions. The hypothesis is that the performance at the elevated temperatures could be improved by allowing a facilitated transport mechanism to become dominant. Several amine-based ionic liquids were tested on the cross-linked nylon support. It was found that using the amine-based ionic liquid did improve selectivity and permeability at higher temperature. The hypothesis was confirmed, and it was determined that the type of amine used also played a role in facilitated transport. Given the appropriate aminated ionic liquid with the cross-linked nylon support, it is possible to have a membrane capable of separating CO2 at IGCC conditions. With this being the case, the research has expanded to include separation of other constituents besides CO2 (CO, H2S, etc.) and if they play a role in membrane poisoning or degradation. This communication will discuss the operation of the recently fabricated ionic liquid membranes and the impact of gaseous components other than CO2 on their performance and stability.

  8. Carbon Dioxide Separation with Supported Ionic Liquid Membranes

    Energy Technology Data Exchange (ETDEWEB)

    Luebke, D.R.; Ilconich, J.B.; Myers, C.R.; Pennline, H.W.

    2007-04-01

    Supported liquid membranes are a class of materials that allow the researcher to utilize the wealth of knowledge available on liquid properties as a direct guide in the development of a capture technology. These membranes also have the advantage of liquid phase diffusivities higher than those observed in polymeric membranes which grant proportionally greater permeabilities. The primary shortcoming of the supported liquid membranes demonstrated in past research has been the lack of stability caused by volatilization of the transport liquid. Ionic liquids, which possess high carbon dioxide solubility relative to light gases such as hydrogen, are an excellent candidate for this type of membrane since they have negligible vapor pressure and are not susceptible to evaporation. A study has been conducted evaluating the use of several ionic liquids, including 1-hexyl-3-methyl-imidazolium bis(trifuoromethylsulfonyl)imide, 1-butyl-3-methyl-imidazolium nitrate, and 1-ethyl-3-methyl-imidazolium sulfate in supported ionic liquid membranes for the capture of carbon dioxide from streams containing hydrogen. In a joint project, researchers at the University of Notre Dame lent expertise in ionic liquid synthesis and characterization, and researchers at the National Energy Technology Laboratory incorporated candidate ionic liquids into supports and evaluated the resulting materials for membrane performance. Initial results have been very promising with carbon dioxide permeabilities as high as 950 barrers and significant improvements in carbon dioxide/hydrogen selectivity over conventional polymers at 37C and at elevated temperatures. Results include a comparison of the performance of several ionic liquids and a number of supports as well as a discussion of innovative fabrication techniques currently under development.

  9. Membrane separation of ionic liquid solutions

    Science.gov (United States)

    Campos, Daniel; Feiring, Andrew Edward; Majumdar, Sudipto; Nemser, Stuart

    2015-09-01

    A membrane separation process using a highly fluorinated polymer membrane that selectively permeates water of an aqueous ionic liquid solution to provide dry ionic liquid. Preferably the polymer is a polymer that includes polymerized perfluoro-2,2-dimethyl-1,3-dioxole (PDD). The process is also capable of removing small molecular compounds such as organic solvents that can be present in the solution. This membrane separation process is suitable for drying the aqueous ionic liquid byproduct from precipitating solutions of biomass dissolved in ionic liquid, and is thus instrumental to providing usable lignocellulosic products for energy consumption and other industrial uses in an environmentally benign manner.

  10. Nanoporous silica membranes with high hydrothermal stability

    DEFF Research Database (Denmark)

    Boffa, Vittorio; Magnacca, Giualiana; Yue, Yuanzheng

    Despite the use of sol-gel derived nanoporous silica membranes in substitution of traditional separation processes is expected leading to vast energy savings, their intrinsic poor steam-stability hampers their application at an industrial level. Transition metal ions can be used as dopant...... to improve the stability of nanoporous silica structure. This work is a quantitative study on the impact of type and concentration of transition metal ions on the microporous structure and stability of amorphous silica-based membranes, which provides information on how to design chemical compositions...... and synthetic paths for the fabrication of silica-based membranes with a well accessible and highly stabile nanoporous structure...

  11. Liquid crystal model of membrane flexoelectricity.

    Science.gov (United States)

    Rey, Alejandro D

    2006-07-01

    An interfacial liquid crystal model is formulated and used to derive a membrane shape equation that takes into account pressure, tension, bending, torsion, and flexoelectric forces. Flexoelectricity introduces electric field-induced curvature and is of relevance to the study and characterization of biological membranes. It is shown that flexoelectricity renormalizes the membrane mechanical tension, shear, and bending effects, and hence it offers diverse pathways to manipulate the membrane's shape. The derived electroelastic shape equation provides systematic guidance on how to use electric fields in membrane studies.

  12. Emulsion Liquid Membrane Technology in Organic Acid Purification

    International Nuclear Information System (INIS)

    Norela Jusoh; Norasikin Othman; Nur Alina Nasruddin

    2016-01-01

    Emulsion Liquid Membrane (ELM) process have shown a great potential in wide application of industrial separations such as in removal of many chemicals, organic compounds, metal ions, pollutants and biomolecules. This system promote many advantages including simple operation, high selectivity, low energy requirement, and single stage extraction and stripping process. One potential application of ELM is in the purification of succinic acid from fermentation broth. This study outline steps for developing emulsion liquid membrane process in purification of succinic acid. The steps include liquid membrane formulation, ELM stability and ELM extraction of succinic acid. Several carrier, diluent and stripping agent was screened to find appropriate membrane formulation. After that, ELM stability was investigated to enhance the recovery of succinic acid. Finally, the performance of ELM was evaluated in the extraction process. Results show that formulated liquid membrane using Amberlite LA2 as carrier, palm oil as diluent and sodium carbonate, Na 2 CO 3 as stripping agent provide good performance in purification. On the other hand, the prepared emulsion was observed to be stable up to 1 hour and sufficient for extraction process. In conclusion, ELM has high potential to purify succinic acid from fermentation broth. (author)

  13. Modeling CO2-facilitated transport across a diethanolamine liquid membrane

    Energy Technology Data Exchange (ETDEWEB)

    Lihong Bao; Michael C. Trachtenberg [Carbozyme Inc., Monmouth Junction, NJ (United States)

    2005-12-15

    We compared experimental and model data for the facilitated transport of CO2 from a CO2-air mixture across an aqueous solution of diethanolamine (DEA) via a hollow fiber, contained liquid membrane (HFCLM) permeator. A two-step carbamate formation model was devised to analyze the data instead of the one-step mechanism used by previous investigators. The effects of DEA concentration, liquid membrane thickness and feed CO2 concentration were also studied. With a 20% (wt) DEA liquid membrane and feed of 15% CO2 in CO2-air mixture at atmosphere pressure, the permeance reached 1.51E-8 mol/m{sup 2} s Pa with a CO2/N2 selectivity of 115. Model predictions compared well with the experimental results at CO2 concentrations of industrial importance. Short-term stability of the HFCLM permeator performance was examined. The system was stable during 5-days of testing.

  14. Supported Liquid Membrane Extraction of Anabolic Androgenic ...

    African Journals Online (AJOL)

    A sample work-up and enrichment technique involving the use of supported liquid membrane (SLM) and detection by high performance liquid chromatography coupled to a mass spectrometer operating under positive ion electrospray mode (LC-PI-ESI-MS) has been developed for the determination of six anabolic ...

  15. Supported Liquid Membrane Extraction of Anabolic Androgenic ...

    African Journals Online (AJOL)

    NJD

    A sample work-up and enrichment technique involving the use of supported liquid membrane (SLM) and detection by high performance liquid chromatography coupled to a mass spectrometer operating under positive ion electrospray mode. (LC-PI-ESI-MS) has been developed for the determination of six anabolic ...

  16. Isomeric Detergent Comparison for Membrane Protein Stability

    DEFF Research Database (Denmark)

    Cho, Kyung Ho; Hariharan, Parameswaran; Mortensen, Jonas S.

    2016-01-01

    Membrane proteins encapsulated by detergent micelles are widely used for structural study. Because of their amphipathic property, detergents have the ability to maintain protein solubility and stability in an aqueous medium. However, conventional detergents have serious limitations in their scope...... and utility, particularly for eukaryotic membrane proteins and membrane protein complexes. Thus, a number of new agents have been devised; some have made significant contributions to membrane protein structural studies. However, few detergent design principles are available. In this study, we prepared meta....../stability of the membrane proteins. We propose that interplay between the hydrophile–lipophile balance (HLB) and alkyl chain length is of central importance for high detergent efficacy. In addition, differences in inter-alkyl-chain distance between the isomers influence the ability of the detergents to stabilise membrane...

  17. Vacuum membrane distillation of liquid desiccants Utilizing Hollow Fiber Membranes

    KAUST Repository

    Lefers, Ryan

    2018-01-31

    This paper documents the testing of a vacuum membrane distillation system intended for use with liquid desiccants. Liquid desiccants offer the possibility for low-energy, ambient temperature dehumidification. Effective desalination and purification of diluted desiccants outputs two important products: a concentrated desiccant for reuse in dehumidification and fresh water. In this study, vacuum membrane distillation was used in the laboratory to purify diluted liquid desiccants. Calcium chloride and magnesium chloride were the desiccants selected for testing. Desiccant solutions were pumped through the lumens of poly(vinylidene fluoride) (PVDF) hollow fiber membranes at varying feed inlet temperatures, solution velocity rates and vacuum set points during membrane distillation. An average flux of 8 kg m-2 h-1 was obtained using 30 wt% magnesium chloride solution at a temperature of 50 °C while applying vacuum to achieve 25 mbar absolute pressure on the air side of the membrane. The results are promising for the development of a full-scale vacuum membrane distillation process for desiccant solution regeneration and fresh water recovery. In addition, the recovered condensate was of sufficient quality for use in agricultural irrigation or drinking water.

  18. Eigenvalues define conditions of stability in liquid-liquid miscible ...

    African Journals Online (AJOL)

    Eigenvalues define conditions of stability in liquid-liquid miscible displacement process. ... Abstract. A miscible displacement process is primarily governed by both convective flow and hydrodynamic dispersion. The proper classification of stability condition in the miscible ... Metrics Loading ... Metrics powered by PLOS ALM

  19. Tubular Steel Arch Stabilized by Textile Membranes

    Directory of Open Access Journals (Sweden)

    Ondrej Svoboda

    2016-10-01

    Full Text Available Tubular steel arch supporting textile membrane roofing is investigated experimentally and numerically. The stabilization effects of the textile membrane on in-plane and out-of-plane behavior of the arch is of primary interest. First a model of a large membrane structure tested in laboratory is described. Prestressed membranes of PVC coated polyester fabric Ferrari® Précontraint 702S were used as a currently standard and excellent material. The test arrangement, loading and resulting load/deflection values are presented. The supporting structure consisted of two steel arch tubes, outer at edge of the membrane and inner supporting interior of the membrane roofing. The stability and strength behavior of the inner tube under both symmetrical and asymmetrical loading was monitored and is shown in some details. Second the SOFiSTiK software was employed to analyze the structural behavior in 3D, using geometrically nonlinear analysis with imperfections (GNIA. The numerical analysis, FE mesh sensitivity, the membrane prestressing and common boundary conditions are validated by test results. Finally a parametrical study concerning stability of mid arch with various geometries in a membrane structure with several supporting arches is presented, with recommendations for a practical design.

  20. Amine-based solvents regeneration in gas-liquid membrane contactor based on asymmetric PVTMS

    NARCIS (Netherlands)

    Volkov, A.V.; Tsarkov, S.E.; Goetheer, E.L.V.; Volkov, V.V.

    2015-01-01

    Asymmetric flat-sheet membranes made of poly(vinyltrimethylsilane) (PVTMS) were studied for the regeneration of amine-based absorption solvents in a membrane gas-liquid contactor at 100°C. It was shown that PVTMS membrane possesses good mechanical and chemical stability in contact with 4 M

  1. Primary metals extraction by liquid membranes

    International Nuclear Information System (INIS)

    Subramanian, K.N.

    1980-01-01

    The extraction of copper and uranium by liquid membranes is presented. The recovery of uranium from wet process phosphoric acid is described. The development of this process has progressed through three stages, firstly the chemistry of uranium extraction as it pertains to liquid membrane systems. This was followed by continuous extraction tests on fresh black acid and on aged acid. Results on a 1 litre/minute pilot plant demonstrated that the process could be operated with a minimum of feed pretreatment and about 90% of uranium could be extracted. The extraction of copper from copper leach liquors is also described. (U.K.)

  2. Cellulose multilayer Membranes manufacture with Ionic liquid

    KAUST Repository

    Livazovic, Sara

    2015-05-09

    Membrane processes are considered energy-efficient for water desalination and treatment. However most membranes are based on polymers prepared from fossil petrochemical sources. The development of multilayer membranes for nanofiltration and ultrafiltration, with thin selective layers of naturally available cellulose has been hampered by the availability of non-aggressive solvents. We propose the manufacture of cellulose membranes based on two approaches: (i) silylation, coating from solutions in tetrahydrofuran, followed by solvent evaporation and cellulose regeneration by acid treatment; (ii) casting from solution in 1-ethyl-3-methylimidazolum acetate ([C2mim]OAc), an ionic liquid, followed by phase inversion in water. By these methods porous supports could be easily coated with semi-crystalline cellulose. The membranes were hydrophilic with contact angles as low as 22.0°, molecular weight cut-off as low as 3000 g mol-1 with corresponding water permeance of 13.8 Lm−2 h−1 bar−1. Self-standing cellulose membranes were also manufactured without porous substrate, using only ionic liquid as green solvent. This membrane was insoluble in water, tetrahydrofuran, hexane, N,N-dimethylformamide, 1-methyl-2-pyrrolidinone and N,N-dimethylacetamide.

  3. Stabilization of Erythrocyte Membranes by Polyamines

    Science.gov (United States)

    Ballas, Samir K.; Mohandas, Narla; Marton, Laurence J.; Shohet, Stephen B.

    1983-04-01

    Using a laser diffraction technique, we have studied the effects of putrescine, spermidine, and spermine, the three physiologic polyamines, on the deformability and mechanical stability of human erythrocyte membranes. Ghosts resealed with polyamines were subjected to high fluid shear stress in an ektacytometer. All polyamines increased the membrane shear modulus (decreased deformability) in a concentration- and time-dependent manner. The order of effectiveness was spermine > spermidine > putrescine. At 10 μ M, spermine appreciably decreased membrane deformability. For the measurement of membrane mechanical stability, resealed ghosts were subjected to constant high shear stress in the ektacytometer and deformability was continuously recorded as the deformable ghosts fragmented into rigid spherical vesicles. Polyamines, especially spermine, caused a noticeable increase in the t1/2 for fragmentation. These effects could not be ascribed to proteolysis or Ca2+-induced transglutamination. That the effects of polyamines were specific and not simply due to their positive charge was demonstrated by the finding that Ca2+ and Mg2+ destabilized the erythrocyte membrane as evidenced by decreasing the t1/2 for fragmentation. Extracellular polyamines were not effective except under conditions that caused significant accumulation inside the cell. The data indicate that intracellular physiologic polyamines, especially spermine, decrease erythrocyte membrane deformability and stabilize the membrane skeleton, making it more resistant to fragmentation.

  4. hollow fibre supported liquid membrane extraction of ...

    African Journals Online (AJOL)

    Preferred Customer

    ABSTRACT. ABSTRACT. A simple sample pre-treatment method utilizing hollow fibre supported liquid membrane. (HFSLM) was carried out on pharmaceuticals samples comprising of cough syrups (CS1 and CS2) and an anti- inflammatory product (AI). The active ingredients targeted in the extraction process were ...

  5. Hollow fibre supported liquid membrane extraction of ...

    African Journals Online (AJOL)

    A simple sample pre-treatment method utilizing hollow fibre supported liquid membrane (HFSLM) was carried out on pharmaceuticals samples comprising of cough syrups (CS1 and CS2) and an anti-inflammatory product (AI). The active ingredients targeted in the extraction process were diphenylhydramine (DPH), ...

  6. Study of ion separation through solid-supported liquid membrane

    International Nuclear Information System (INIS)

    Kang, Young Ho; Kim, Jung Do; Kim, Kyoung Ho

    1990-01-01

    The membranes used in this study consist of a microporous polymeric support with the solvent contraining alamine 336, Tri-N-Octyl phosphine oxide, Tri-N-butyl phosphate, Di-(2-ethylhexyl) phosphoric acid as a carrier within the pores by the capillary forces. When this liquid membrane is interposed between aqueous feed and product solutions, the carrier serving as a complexing agent, can pick up the uranium ions on the feed side of the membrane and carry them across the membrane by diffusion. In this study, the uranium flux through the solid-supported liquid membrane was analyzed as a function of carrier concentration and acidity of the feed solution for the carrier species. Also, the Gel-liquid extraction of uranium ions from aqueous solution was performed. The adsorbents were prepared by casting the polymer solution composed of polyvinyl chloride, TOPO, and additions. The extraction of uranyl nitrate ions has been investigated as a function of TOPO/PVC ratio, evaporation time, and the stability. The results show that is maybe possible to develop an alternative uranium purification process. (author)

  7. Supported liquid membranes technologies in metals removal from liquid effluents

    Directory of Open Access Journals (Sweden)

    de Agreda, D.

    2011-04-01

    Full Text Available The generation of liquid effluents containing organic and inorganic residues from industries present a potential hazardousness for environment and human health, being mandatory the elimination of these pollutants from the respective solutions containing them. In order to achieve this goal, several techniques are being used and among them, supported liquid membranes technologies are showing their potential for their application in the removal of metals contained in liquid effluents. Supported liquid membranes are a combination between conventional polymeric membranes and solvent extraction. Several configurations are used: flat-sheet supported liquid membranes, spiral wounds and hollow fiber modules. In order to improve their effectiveness, smart operations have been developed: non-dispersive solvent extraction, non-dispersive solvent extraction with strip phase dispersion and hollow fiber renewal liquid membrane. This paper overviewed some of these supported liquid membranes technologies and their applications to the treatment of metal-bearing liquid effluents.

    La generación, por parte de las industrias, de efluentes líquidos conteniendo sustancias orgánicas e inorgánicas, es un peligro potencial tanto para los humanos como para el medio ambiente, siendo necesaria la eliminación de estos elementos tóxicos de las disoluciones que los contienen. Para conseguir este fin, se están aplicando diversas técnicas y entre ellas las tecnologías de membranas líquidas soportadas, están demostrando sus aptitudes para la eliminación de metales contenidos en efluentes líquidos. Las membranas líquidas soportadas, resultan de la unión de las membranas poliméricas y de la tecnología de extracción líquido-líquido. Este tipo de membranas se pueden utilizar en diversas configuraciones: plana, módulo en fibra hueca y módulo en espiral y para aumentar su efectividad se están desarrollando las llamadas operaciones avanzadas: extracción no

  8. Pickering Membranes Stabilized by Saturn Particles.

    Science.gov (United States)

    Krejca, Matthias M; Wüstner, Cornell; Goedel, Werner A

    2017-10-17

    We report on a novel method to synthesize particles-called by us Saturn particles-having two hydrophobic caps that oppose each other and are separated from each other by a hydrophilic belt that encircles the particle. Mixtures of these particles with water and air, without the usage of low molar mass surfactants, easily form Pickering foams and Pickering membranes that are stable for days. These Pickering membranes are composed of a thin film of water into which the particles are embedded in such a way that the belt is surrounded by the water and the caps protrude out of the water into the air at the top and bottom side of the water film. As expected for a liquid membrane, these Pickering membranes are permeable for gases, with the permeance being proportional to the solubility and diffusion coefficient of the gas considered. Experimentally obtained permeance values agree reasonably well with theoretical calculations.

  9. Evaluation of antioxidant capacity and membrane stabilizing ...

    African Journals Online (AJOL)

    Comparative analyses of the antioxidant and membrane stabilizing activities of ethanolic extracts of leaf and root of Cyphospenna adenocaulis (Steud) were investigated with a view to further investigate the biological activities of the plant. Both the leaf and root of C. adenocaulis were extracted with 70% ethanol to yield the ...

  10. Membrane chemical stability and seed longevity

    NARCIS (Netherlands)

    Golovina, E.A.; Hoekstra, F.A.; As, van H.

    2010-01-01

    Here, we investigate the relationships between the chemical stability of the membrane surface and seed longevity. Dry embryos of long-lived tomato and short-lived onion seeds were labeled with 5-doxyl-stearic acid (5-DS). Temperature-induced loss of the electron spin resonance signal caused by

  11. Evaluation of antioxidant capacity and membrane stabilizing ...

    African Journals Online (AJOL)

    Kemi Akinwunmi

    2015-05-27

    May 27, 2015 ... Comparative analyses of the antioxidant and membrane stabilizing activities of ethanolic extracts of leaf and root of Cyphospenna adenocaulis (Steud) were investigated with a view to further investigate the biological activities of the plant. Both the leaf and root of C. adenocaulis were extracted with 70%.

  12. Membrane chemical stability and seed longevity.

    Science.gov (United States)

    Golovina, Elena A; Van As, Henk; Hoekstra, Folkert A

    2010-03-01

    Here, we investigate the relationships between the chemical stability of the membrane surface and seed longevity. Dry embryos of long-lived tomato and short-lived onion seeds were labeled with 5-doxyl-stearic acid (5-DS). Temperature-induced loss of the electron spin resonance signal caused by chemical conversion of 5-DS to nonparamagnetic species was used to characterize the membrane surface chemical stability. No difference was found between temperature plots of 5-DS signal intensity in dry onion and tomato below 345 K. Above this temperature, the 5-DS signal remained unchanged in tomato embryos and irreversibly disappeared in onion seeds. The role of the physical state and chemical status of the membrane environment in the chemical stability of membrane surfaces was estimated for model systems containing 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine (POPC) dried alone or in the presence of trehalose or glucose. Fourier transform infrared spectroscopy was used to follow temperature-induced structural changes in dry POPC. Spin-label technique was used to relate the chemical stability of 5-DS with the dynamic properties of the bilayer and 5-DS motion behavior. In all the models, the decrease in 5-DS signal intensity was always observed above T(m) for the membrane surface. The 5-DS signal was irreversibly lost at high temperature when dry POPC was embedded in a glucose matrix. The loss of 5-DS signal was moderate when POPC was dried alone or in the presence of trehalose. Comparison of model and in vivo data shows that the differences in longevity between onion and tomato seeds are caused by differences in the chemical status of the membrane surface rather than the degree of its immobilization.

  13. Liquid immiscibility in model bilayer lipid membranes

    Science.gov (United States)

    Veatch, Sarah L.

    There is growing evidence that cell plasma membranes are laterally organized into "raft" regions in which particular lipids and proteins are concentrated. These domains have sub-micron dimensions and have been implicated in vital cell functions. Similar liquid domains are observed in model bilayer membrane mixtures that mimick cellular lipid compositions. In model membranes, domains can be large (microns) and can readily form in the absence of proteins. This thesis presents studies of liquid immiscibility in model membrane systems using two experimental methods. By fluorescence microscopy, this thesis documents that miscibility transitions occur in a wide variety of ternary lipid mixtures containing high melting temperature (saturated) lipids, low melting temperature (usually unsaturated) lipids, and cholesterol. I have constructed detailed miscibility phase diagrams for three separate ternary lipid mixtures (DOPC/DPPC/Chol, DOPC/PSM/Chol, and POPC/PSM/Chol). Phase separation is also observed in membranes of lipids extracted from human erythrocytes. NMR experiments probe lipid order and verify the coexistence of a saturated lipid and cholesterol rich liquid ordered (Lo) phase with a more disordered, unsaturated lipid rich liquid crystalline (Lalpha) phase at low temperatures. These experiments also find multiple thermodynamic transitions and lipid organization on different length-scales. This complexity is revealed because fluorescence microscopy and NMR probe lipid order at different length-scales (>1mum vs. ˜100nm). NMR detects small domains (˜80nm) at temperatures just below the miscibility transition, even though micron-scale domains are observed by fluorescent microscopy. NMR does detect large-scale ("100nm) demixing, but at a lower temperature. In addition, it has long been known that >10nm length-scale structure is present in many lipid mixtures containing cholesterol and at least one additional lipid species, though it is shown here that only a subset of

  14. Poly (ether imide sulfone) membranes from solutions in ionic liquids

    KAUST Repository

    Kim, Dooli

    2017-11-20

    A membrane manufacture method based on non-volatile solvents and a high performance polymer, poly (ether imide sulfone) (EXTEM™), is proposed, as greener alternative to currently industrial process. We dissolved EXTEM™ in pure ionic liquids: 1-ethyl-3-methylimidalzolium thiocyanate ([EMIM]SCN), 1-butyl-3-methylimidalzolium thiocyanate ([BMIM]SCN), and 1-ethyl-3-methylimidalzolium acetate ([EMIM]OAc). The following polymer solution parameters were evaluated to optimize the manufacture: Gibbs free energy of mixing (G), intrinsic viscosity ([]) and hydrodynamic diameter. Membranes with sponge-like structure and narrow pore size distribution were obtained from solutions in [EMIM]SCN. They were tested for separation of proteins and deoxyribonucleic acids (DNA). Due to the polymer stability, we foresee that applications in more demanding chemical separations would be possible. [EMIM]SCN was 96 % purified and recovered after the membrane fabrication, contributing to the sustainability of the whole manufacturing process.

  15. Graphene oxide doped ionic liquid ultrathin composite membranes for efficient CO2 capture

    KAUST Repository

    Karunakaran, Madhavan

    2016-11-28

    Advanced membrane systems with high flux and sufficient selectivity are required for industrial gas separation processes. In order to achieve high flux and high selectivity, the membrane material should be as thin as possible and it should have selective sieving channels and long term stability. This could be achieved by designing a three component material consisting of a blend of an ionic liquid and graphene oxide covered by a highly permeable low selective polymeric coating. By using a simple dip coating technique, we prepared high flux and CO selective ultrathin graphene oxide (GO)/ionic liquid membranes on a porous ultrafiltration support. The ultrathin composite membranes derived from GO/ionic liquid complex displays remarkable combinations of permeability (CO flux: 37 GPU) and selectivity (CO/N selectivity: 130) that surpass the upper bound of ionic liquid membranes for CO/N separation. Moreover, the membranes were stable when tested for 120 hours.

  16. Liquid separation by a graphene membrane

    Science.gov (United States)

    Fileti, E. E.; Dalpian, G. M.; Rivelino, R.

    2010-12-01

    The behavior of liquids separated by a single graphene membrane has been studied with extensive molecular dynamics (MD) simulations at ambient conditions. With the help of appropriate empirical potentials, we have exploited two liquid phases forming distinct systems; say XGY, where G stands for graphene and X (Y) represents water (W), benzene (B), or acetonitrile (A). Our MD simulations revealed important changes in the wettability patterns of these liquids near the graphene surface. For instance, WGW exhibits strong density oscillations in a thin interfacial region with thickness of ˜2.4 nm. In the case of BGB and AGA the oscillating-density interfacial region extends beyond ˜3 nm and ˜5 nm, respectively, under ambient conditions. More interestingly, our findings indicate that a liquid at one side of the graphene sheet can affect the degree of wetting on the other side, by means of dispersion interactions through the graphene membrane. These systems can offer a useful framework to understand the structural as well as thermodynamic properties of interfaces by considering a real two-dimensional substrate.

  17. Extraction by means of emulsified liquid membranes

    International Nuclear Information System (INIS)

    Pareau, D.; Stambouli, M.

    2006-01-01

    It is an alternative of the liquid-liquid extraction process where extraction and stripping are simultaneously carried out. The stripping solution is dispersed in the solvent in micro-droplets. This emulsion, stabilised by a surface-active agent, is then dispersed in the liquid to be treated and, during that step, the metal is transferred to the stripping solution, moving through the solvent which operates as an organic membrane. The paper describes in detail the mechanism of the process, its advantages and its disadvantages. Its field of applications is wide, but only a few units are now industrially in operation, most of them exists only at the pilot scale. It is particularly adapted for the treatment of effluents with a very low content in metallic impurities. As examples, the paper describes the recovery of zinc from viscose plant effluents (Lenzing plant, Austria) and the removal of free cyanide ions and cyanide metallic complexes (pilot scale). (authors)

  18. Membrane technologies for liquid radioactive waste treatment

    International Nuclear Information System (INIS)

    Chmielewski, A.G.; Harasimowicz, M.; Zakrzewska-Trznadel, G.

    1998-01-01

    At Institute of Nuclear Chemistry and Technology (INCT) the membrane method for purification of radioactive wastes applied such processes as ultrafiltration (UF), 'seeded' ultrafiltration and reverse osmosis (RO) was developed. On the basis of the results obtained in laboratory experiments the pilot plant for radioactive effluents treatment was built. The plant was composed of UF unit (AMICON H 26P30 capillary module) and two RO units (NITTO NTR 739 HF S-4 spiral wound LPRO modules). The capacity of the pilot plant was up to 200 L/h and the specific activity of wastes purified in the system - below 10 4 Bq/L. Decontamination factor for entire system is higher than 5 x10 3 . Another possibility for radioactive wastes treatment is membrane distillation (MD), non-isothermal process employing hydrophobic polymer membrane, which is developed at INCT now. Preliminary tests with liquid radwaste were carried out on laboratory unit with permeation test-cell holding flat sheet membrane. As a hydrophobic barrier membranes made of two polymers were used: polytetrafluoroethylene (PTFE) and polypropylene (PP). The process was arranged in direct contact membrane distillation configuration. The permeate condensed directly in the cold stream (distilled water) and retentate was enriched in radionuclides. The further experiments carried out with capillary module BFMF 06-30-33 (Euro-Sep Ltd.) with polypropylene capillaries, diameter 0.33 mm and cut off 0.6 μm proved previous results. A pilot plant employing GORE-TEX membrane distillation was constructed. The plant can clean the low-level radioactive wastes from nuclear centre, at a throughput about 0.05 m 3 /h

  19. High-throughput liquid-liquid extraction in 96-well format: Parallel artificial liquid membrane extraction

    DEFF Research Database (Denmark)

    Gjelstad, Astrid; Andresen, Alf Terje; Dahlgren, Anders

    2017-01-01

    Parallel artificial liquid membrane extraction (PALME) is a miniaturized version of liquid–liquid extraction (LLE) and is based on two 96-well plates in a sandwich-like configuration. With a very simple workflow, 96 samples can be processed simultaneously in PALME, providing analyte enrichment...

  20. Performance evaluation of organic emulsion liquid membrane on phenol removal

    OpenAIRE

    Ng, Yee Sern; Jayakumar, N.S.; Hashim, M.A.

    2017-01-01

    The percentage removal of phenol from aqueous solution by emulsion liquid membrane and emulsion leakage was investigated experimentally for various parameters such as membrane:internal phase ratio, membrane:external phase ratio, emulsification speed, emulsification time, carrier concentration, surfactant concentration and internal agent concentration. These parameters strongly influence the percentage removal of phenol and emulsion leakage. Under optimum membrane properties, the percentage re...

  1. A microgrooved membrane based gas–liquid contactor

    NARCIS (Netherlands)

    Jani, J.M.; Wessling, Matthias; Lammertink, Rob G.H.

    2012-01-01

    This research presents an approach for applying microgrooved membranes for improved gas–liquid contacting. The study involves analysis of the performance of the microdevice by quantifying the flux enhancement for different membrane configurations. Two kinds of configurations, continuous and

  2. Study of cyanide wastewater treatment by dispersion supported liquid membrane using trioctylamine and kerosene as liquid membrane.

    Science.gov (United States)

    Li, Guo Ping; Xue, Juan Qin; Yu, Li Hua; Liu, Ni Na

    2015-01-01

    A certain amount of cyanide is present in wastewater of various industrial processes, such as wet extraction of gold, coal processing, electroplating and other industries. In this work, an experimental study regarding transport of cyanide through a dispersion supported liquid membrane was performed. A model was established to describe the reaction and transport of CN(I) in the supported liquid membrane and the mass transfer kinetics equations were deduced. Through mass transfer kinetic equation it was derived that, when the carrier concentration was under certain conditions, there was a linear relationship between the reciprocal of the permeability coefficient of CN(I) (1/Pc) and n-th power of the concentration of H+ (cnH+), and the parameters Δa(δa/da) and Δo(δ0/d0) could be obtained from the slope and intercept of the straight line. Then the diffusion coefficient do and the diffusion layer thickness δo of the phase interface between the feed phase and membrane phase could be calculated. Factors affecting migration of CN(I) were analyzed, and the stable removal rate of CN(I) was more than 90% with carrier concentration (%TOA) of 2%, feed phase pH of 4, initial CN(I) concentration of 30 mg/L, stirring time of 1 hour, volume ratio of membrane solution to NaOH solution of 2:1, strip phase concentration of 2 mol/L. The results showed that the overall mass transfer rate increased first and then decreased with an increase of TOA concentration, organic-to-strip volume ratio, and strip concentration. Furthermore, the transport percentage of CN(I) was increased, the stability of membrane was enhanced, and the lifetime of the membrane was extended.

  3. Application of membrane technologies for liquid radioactive waste processing

    International Nuclear Information System (INIS)

    2004-01-01

    Membrane separation processes have made impressive progress since the first synthesis of membranes almost 40 years ago. This progress was driven by strong technological needs and commercial expectations. As a result the range of successful applications of membranes and membrane processes is continuously broadening. In addition, increasing application of membrane processes and technologies lies in the increasing variations of the nature and characteristics of commercial membranes and membrane apparatus. The objective of the report is to review the information on application of membrane technologies in the processing of liquid radioactive waste. The report covers the various types of membranes, equipment design, range of applications, operational experience and the performance characteristics of different membrane processes. The report aims to provide Member States with basic information on the applicability and limitations of membrane separation technologies for processing liquid radioactive waste streams

  4. Potential of membrane processes in management of radioactive liquid waste

    International Nuclear Information System (INIS)

    Kumar, Surender; Jain, Savita; Raj, Kanwar

    2010-01-01

    Various categories of radioactive liquid waste are generated during operations and maintenance of nuclear installations. The potential of membrane processes for the treatment of low-level radioactive liquids is discussed in this paper

  5. Pervaporation and Gas Separation with Supported Liquid Membranes.

    OpenAIRE

    Izák, Pavel

    2016-01-01

    The goal of this work is to combine the recent developments in the field of membrane technology, e.g. supported liquid membranes, pervaporation and gas separation with the use of ionic liquids (ILs) for providing novel solutions in downstream processing or process intensification.

  6. Supported Liquid Membrane Principle and Its Practices: A Short Review

    Directory of Open Access Journals (Sweden)

    P. K. Parhi

    2013-01-01

    Full Text Available The present paper on the supported liquid membrane (SLM deals with the general principles and applications, followed by the uphill transportation characteristic of SLM. The liquid-liquid extraction with supported liquid membrane is one of the best alternate and promising technologies for the extraction of metal ions from solutions over other hydrometallurgical separation processes. The salient features of the supported liquid membrane (SLM technique such as simultaneous extraction and stripping, low solvent inventory, process economy, high efficiency, less extractant consumption, and operating costs are discussed in detail. The supported liquid membrane of hollow fiber type provides high interfacial surface area for achieving maximum metal flux. Also the use of different organic extractants for SLM has been discussed.

  7. Dynamic stabilization of imploding liquid metal liner

    International Nuclear Information System (INIS)

    Itoh, Yasuyuki; Fujiie, Yoichi

    1979-01-01

    The rotational stabilization has been proposed against the Rayleigh-Taylor instability of the imploding liquid metal liner. In this paper, the discussion is made on the possibility of the dynamic stabilization by applying the oscillating azimuthal magnetic field in addition to the axial field. In contrast to the rotational stabilization, the required (field) energy for this stabilization is also used for the liner driving or the plasma confinement. In the analysis, the liner subjected to the acceleration is assumed to be infinitely long, at rest and have the situation at the start of the implosion or turnaround. At turnaround, the existence of the plasma is taken into account. The perturbed motion of the liner is discussed with a linear stability analysis. Results are as follows: (1) The dynamic stabilization at the start of the implosion is possible if the distance from the conducting wall to the liner outer surface is comparable with or less than the liner thickness. (2) At turnaround, the stability is improved with decreasing the ratio of the plasma radius to that of the liner inner surface however the kink mode (m = 1) cannot be suppressed. (author)

  8. Effect of Viscosity on Liquid Curtain Stability

    Science.gov (United States)

    Mohammad Karim, Alireza; Suszynski, Wieslaw; Francis, Lorraine; Carvalho, Marcio; Dow Chemical Company Collaboration; PUC Rio Collaboration; University of Minnesota, Twin Cities Collaboration

    2016-11-01

    The effect of viscosity on the stability of Newtonian liquid curtains was explored by high-speed visualization. Glycerol/water solutions with viscosity ranging from 19.1 to 210 mPa.s were used as coating liquids. The experimental set-up used a slide die delivery and steel tube edge guides. The velocity along curtain at different positions was measured by tracking small particles at different flow conditions. The measurements revealed that away from edge guides, velocity is well described by free fall effect. However, close to edge guides, liquid moves slower, revealing formation of a viscous boundary layer. The size of boundary layer and velocity near edge guides are strong function of viscosity. The critical condition was determined by examining flow rate below which curtain broke. Curtain failure was initiated by growth of a hole within liquid curtain, close to edge guides. Visualization results showed that the hole forms in a circular shape then becomes elliptical as it grows faster in vertical direction compared to horizontal direction. As viscosity rises, minimum flow rate for destabilization of curtain increased, indicating connection between interaction with edge guides and curtain stability. We would like to acknowledge the financial support from the Dow Chemical Company.

  9. Metal-organic frameworks based membranes for liquid separation.

    Science.gov (United States)

    Li, Xin; Liu, Yuxin; Wang, Jing; Gascon, Jorge; Li, Jiansheng; Van der Bruggen, Bart

    2017-11-27

    Metal-organic frameworks (MOFs) represent a fascinating class of solid crystalline materials which can be self-assembled in a straightforward manner by the coordination of metal ions or clusters with organic ligands. Owing to their intrinsic porous characteristics, unique chemical versatility and abundant functionalities, MOFs have received substantial attention for diverse industrial applications, including membrane separation. Exciting research activities ranging from fabrication strategies to separation applications of MOF-based membranes have appeared. Inspired by the marvelous achievements of MOF-based membranes in gas separations, liquid separations are also being explored for the purpose of constructing continuous MOFs membranes or MOF-based mixed matrix membranes. Although these are in an emerging stage of vigorous development, most efforts are directed towards improving the liquid separation efficiency with well-designed MOF-based membranes. Therefore, as an increasing trend in membrane separation, the field of MOF-based membranes for liquid separation is highlighted in this review. The criteria for judicious selection of MOFs in fabricating MOF-based membranes are given. Special attention is paid to rational design strategies for MOF-based membranes, along with the latest application progress in the area of liquid separations, such as pervaporation, water treatment, and organic solvent nanofiltration. Moreover, some attractive dual-function applications of MOF-based membranes in the removal of micropollutants, degradation, and antibacterial activity are also reviewed. Finally, we define the remaining challenges and future opportunities in this field. This Tutorial Review provides an overview and outlook for MOF-based membranes for liquid separations. Further development of MOF-based membranes for liquid separation must consider the demands of strict separation standards and environmental safety for industrial application.

  10. Metal–organic frameworks based membranes for liquid separation

    KAUST Repository

    Li, Xin

    2017-11-07

    Metal-organic frameworks (MOFs) represent a fascinating class of solid crystalline materials which can be self-assembled in a straightforward manner by the coordination of metal ions or clusters with organic ligands. Owing to their intrinsic porous characteristics, unique chemical versatility and abundant functionalities, MOFs have received substantial attention for diverse industrial applications, including membrane separation. Exciting research activities ranging from fabrication strategies to separation applications of MOF-based membranes have appeared. Inspired by the marvelous achievements of MOF-based membranes in gas separations, liquid separations are also being explored for the purpose of constructing continuous MOFs membranes or MOF-based mixed matrix membranes. Although these are in an emerging stage of vigorous development, most efforts are directed towards improving the liquid separation efficiency with well-designed MOF-based membranes. Therefore, as an increasing trend in membrane separation, the field of MOF-based membranes for liquid separation is highlighted in this review. The criteria for judicious selection of MOFs in fabricating MOF-based membranes are given. Special attention is paid to rational design strategies for MOF-based membranes, along with the latest application progress in the area of liquid separations, such as pervaporation, water treatment, and organic solvent nanofiltration. Moreover, some attractive dual-function applications of MOF-based membranes in the removal of micropollutants, degradation, and antibacterial activity are also reviewed. Finally, we define the remaining challenges and future opportunities in this field. This Tutorial Review provides an overview and outlook for MOF-based membranes for liquid separations. Further development of MOF-based membranes for liquid separation must consider the demands of strict separation standards and environmental safety for industrial application.

  11. Membrane Stabilizing Activity And Phytochemistry Of Hibiscus rosa ...

    African Journals Online (AJOL)

    The human erythrocyte membrane stabilizing activity of saline extract of Hibiscus rosa-sinensis leaves was investigated as part of efforts at validating its use as anti-arthritic and anti-inflammatory agent. The results of the membrane stabilizing activity of the extract, when compared to two non-steroidal anti-inflammatory drugs ...

  12. Membrane-solvent selection for CO2 removal using membrane gas-liquid contactors

    NARCIS (Netherlands)

    Dindore, V.Y.; Brilman, Derk Willem Frederik; Geuzebroek, F.H.; Versteeg, Geert

    2004-01-01

    Membrane gas–liquid contactors can provide very high interfacial area per unit volume, independent regulation of gas and liquid flows and are insensitive to module orientation, which make them very attractive in comparison with conventional equipments for offshore application. However, the membrane

  13. Long term physical and chemical stability of polyelectrolyte multilayer membranes

    NARCIS (Netherlands)

    de Grooth, Joris; Haakmeester, Brian; Wever, Carlos; Potreck, Jens; de Vos, Wiebe Matthijs; Nijmeijer, Dorothea C.

    2015-01-01

    This work presents a detailed investigation into the long term stability of polyelectrolyte multilayer (PEM) modified membranes, a key factor for the application of these membranes in water purification processes. Although PEM modified membranes have been frequently investigated, their long term

  14. Hydrothermal stability of microporous silica and niobia-silica membranes

    NARCIS (Netherlands)

    Boffa, V.; Blank, David H.A.; ten Elshof, Johan E.

    2008-01-01

    The hydrothermal stability of microporous niobia–silica membranes was investigated and compared with silica membranes. The membranes were exposed to hydrothermal conditions at 150 and 200 °C for 70 h. The change of pore structure before and after exposure to steam was probed by single-gas permeation

  15. Novel composite membranes based on PBI and dicationic ionic liquids for high temperature polymer electrolyte membrane fuel cells

    International Nuclear Information System (INIS)

    Hooshyari, Khadijeh; Javanbakht, Mehran; Adibi, Mina

    2016-01-01

    Two types of innovative composite membranes based on polybenzimidazole (PBI) containing dicationic ionic liquid 1,3-di(3-methylimidazolium) propane bis (trifluoromethylsulfonyl) imide (PDC 3 ) and monocationic ionic liquid 1-hexyl-3-methylimidazolium bis (trifluoromethanesulfonyl) imide (PMC 6 ) are prepared as electrolyte for high temperature fuel cells applications under anhydrous conditions. The analyses of results display promising characteristics such as high proton conductivity and thermal stability. Moreover the fuel cell performance of PA doped PDC 3 composite membranes is enhanced in comparison with PA doped PMC 6 and PA doped PBI membranes at high temperatures. Dicationic ionic liquid with high number of charge carriers provides well-developed ionic channels which form facile pathways and considerably develop the anhydrous proton conductivity. The highest proton conductivity of 81 mS/cm is achieved for PA doped PDC 3 composite membranes with PBI/IL mole ratio: 4 at 180 °C. A power density of 0.44 W/cm 2 is obtained at 0.5 V and 180 °C for PA doped PDC 3 composite membranes, which proves that these developed composite membranes can be considered as most promising candidates for high temperature fuel cell applications with enhanced proton conductivity.

  16. Catalytic Ionic-Liquid Membranes: The Convergence of Ionic-Liquid Catalysis and Ionic-Liquid Membrane Separation Technologies.

    Czech Academy of Sciences Publication Activity Database

    Izák, Pavel; Bobbink, F.D.; Hulla, M.; Klepic, M.; Friess, K.; Hovorka, Š.; Dyson, P.J.

    2018-01-01

    Roč. 83, č. 1 (2018), s. 7-18 ISSN 2192-6506 R&D Projects: GA ČR(CZ) GA17-00089S; GA ČR GA17-05421S Institutional support: RVO:67985858 Keywords : heterogeneous catalysis * ionic liquids * membranes Subject RIV: CI - Industrial Chemistry, Chemical Engineering OBOR OECD: Chemical process engineering Impact factor: 2.797, year: 2016

  17. Catalytic Ionic-Liquid Membranes: The Convergence of Ionic-Liquid Catalysis and Ionic-Liquid Membrane Separation Technologies.

    Czech Academy of Sciences Publication Activity Database

    Izák, Pavel; Bobbink, F.D.; Hulla, M.; Klepic, M.; Friess, K.; Hovorka, Š.; Dyson, P.J.

    2018-01-01

    Roč. 83, č. 1 (2018), s. 7-18 ISSN 2192-6506 R&D Projects: GA ČR(CZ) GA17-00089S; GA ČR GA17-05421S Institutional support: RVO:67985858 Keywords : heterogeneous catalysis * ionic liquid s * membranes Subject RIV: CI - Industrial Chemistry, Chemical Engineering OBOR OECD: Chemical process engineering Impact factor: 2.797, year: 2016

  18. (Meth)acrylate liquid crystalline polymers for membrane applications

    Czech Academy of Sciences Publication Activity Database

    Rabie, F.; Sedláková, Zdeňka; Sheth, S.; Marand, E.; Martin, S. M.; Poláková, Lenka

    2015-01-01

    Roč. 132, č. 43 (2015), 42694_1-42694_8 ISSN 0021-8995 Institutional support: RVO:61389013 Keywords : copolymers * liquid crystals * membranes Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.866, year: 2015

  19. Experimental performance of indirect air–liquid membrane contactors for liquid desiccant cooling systems

    International Nuclear Information System (INIS)

    Das, Rajat Subhra; Jain, Sanjeev

    2013-01-01

    Owing to the stringent indoor air quality (IAQ) requirements and high cost of desiccants, one of the major concerns in liquid desiccant technology has been the carryover, which can be eliminated through indirect contact between desiccant and air. Membrane contactors using microporous semipermeable hydrophobic membranes have a great potential in this regard. This communication investigates the performance of semipermeable membrane based indirect contactors as dehumidifiers in liquid desiccant cooling applications. Experiments on different types of membrane contactors are carried out using lithium chloride (LiCl) solution as desiccant. The membrane contactors consist of alternate channels of air and liquid desiccant flowing in cross-flow direction. Hydrophobic membranes form a liquid tight, vapor permeable porous barrier between hygroscopic solution and moist air, thus eliminating carryover of desiccant droplets. In order to provide maximum contact area for air–desiccant interaction, a wicking material is sandwiched between two membranes in the liquid channel. It is observed that vapor flux upto 1300 g/m 2 h can be achieved in a membrane contactor with polypropylene (PP) membranes, although the dehumidification effectiveness remains low. The effect of key parameters on the transmembrane vapor transport is presented in the paper. - Highlights: • Indirect membrane contactors developed to avoid carryover in liquid desiccant system. • Dehumidification effectiveness and vapor flux reported under varying conditions. • Vapor flux upto 1295 g/m 2 h in polypropylene contactor with high area density. • Dehumidification effectiveness with LiCl solution varies within 23% to 45%

  20. Fabrication of Polyacrylonitrile Hollow Fiber Membranes from Ionic Liquid Solutions

    KAUST Repository

    Kim, Dooli

    2015-10-08

    The interest in green processes and products has increased to reduce the negative impact of many industrial processes to the environment. Solvents, which play a crucial role in the fabrication of membranes, need to be replaced by sustainable and less toxic solvent alternatives for commonly used polymers. The purpose of this study is the fabrication of greener hollow fiber membranes based on polyacrylonitrile (PAN), substituting dimethylformamide (DMF) by less toxic mixtures of ionic liquids (IL) and dimethylsulfoxide (DMSO). A thermodynamic analysis was conducted, estimating the Gibbs free energy of mixing to find the most convenient solution compositions. Hollow fiber membranes were manufactured and optimized. As a result, a uniform pattern and high porosity were observed in the inner surface of the membranes prepared from the ionic liquid solutions. The membranes were coated with a polyamide layer by interfacial polymerization the hollow fiber membranes were applied in forward osmosis experiments by using sucrose solutions as draw solution.

  1. Membrane curvature enables N-Ras lipid anchor sorting to liquid-ordered membrane phases

    DEFF Research Database (Denmark)

    Larsen, Jannik Bruun; Jensen, Martin Borch; Bhatia, Vikram Kjøller

    2015-01-01

    Trafficking and sorting of membrane-anchored Ras GTPases are regulated by partitioning between distinct membrane domains. Here, in vitro experiments and microscopic molecular theory reveal membrane curvature as a new modulator of N-Ras lipid anchor and palmitoyl chain partitioning. Membrane curva...... curvature was essential for enrichment in raft-like liquid-ordered phases; enrichment was driven by relief of lateral pressure upon anchor insertion and most likely affects the localization of lipidated proteins in general....

  2. Modeling of gadolinium recovery from nitrate medium with 8-hydroxyquinoline by emulsion liquid membrane

    International Nuclear Information System (INIS)

    Hasan, M.A.; Aglan, R.F.; El-Reefy, S.A.

    2009-01-01

    The extraction equilibrium of Gd(III) from nitrate medium by 8-hydroxyquinoline (HOX) in toluene was studied. Liquid-liquid investigations were first carried out. Based on the equilibrium results, the extraction of Gd(III) from aqueous nitrate medium into an emulsion liquid membrane system (ELM) containing 8-hydroxyquinoline in toluene as extractant, HNO 3 as stripping solution, Span-80 as surfactant was studied. The stability of the prepared ELM was studied in terms of the degree of membrane breakage. The different parameters affecting the permeation of gadolinium (III) were also studied. A general permeation model for the recovery of Gd(III) by the selected membrane is presented. The internal mass transfer in the water in oil (W/O) emulsion drop, the external mass transfer around the drop, the rates of formation and decomposition of the complex at the external aqueous-organic interface were considered.

  3. Fabrication of Greener Membranes from Ionic Liquid Solutions

    KAUST Repository

    Kim, DooLi

    2017-06-01

    Membrane technology plays a crucial role in different separation processes such as biotechnology, pharmaceutical, and food industries, drinking water supply, and wastewater treatment. However, there is a growing concern that solvents commonly used for membrane fabrication, such as dimethylformamide (DMF), dimethylacetamide (DMAc), and 1-methyl-2-pyrrolidone (NMP), are toxic to the environment and human health. To explore the possibility of substituting these toxic solvents by less toxic or safer solvents, polymers commonly used for membrane fabrication, such as polyacrylonitrile (PAN), cellulose acetate (CA), polyethersulfone (PES), and poly(ether imide sulfone) (EXTEMTM), were dissolved in ionic liquids. Flat sheet and hollow fiber membranes were then fabricated. The thermodynamics of the polymer solutions, the kinetics of phase inversion and other factors, which resulted in significant differences in the membrane structure, compared to those of membranes fabricated from more toxic solvents, were investigated. Higher water permeance with smaller pores, unique and uniform morphologies, and narrower pore size distribution, were observed in the ionic liquid-based membranes. Furthermore, comparable performance on separation of peptides and proteins with various molecular weights was achieved with the membranes fabricated from ionic liquid solutions. In summary, we propose less hazardous polymer solutions to the environment, which can be used for the membrane fabrication with better performance and more regular morphology.

  4. Deashing of coal liquids with ceramic membrane microfiltration and diafiltration

    Energy Technology Data Exchange (ETDEWEB)

    Bishop, B.; Goldsmith, R. [CeraMem Corp., Waltham, MA (United States)

    1995-12-31

    Removal of mineral matter from liquid hydrocarbons derived from the direct liquefaction of coal is required for product acceptability. Current methods include critical solvent deashing (Rose{sup {reg_sign}} process from Kerr-McGee) and filtration (U.S. Filter leaf filter as used by British Coal). These methods produce ash reject streams containing up to 15% of the liquid hydrocarbon product. Consequently, CeraMem proposed the use of low cost, ceramic crossflow membranes for the filtration of coal liquids bottoms to remove mineral matter and subsequent diafiltration (analogous to cake washing in dead-ended filtration) for the removal of coal liquid from the solids stream. The use of these ceramic crossflow membranes overcomes the limitations of traditional polymeric crossflow membranes by having the ability to operate at elevated temperature and to withstand prolonged exposure to hydrocarbon and solvent media. In addition, CeraMem`s membrane filters are significantly less expensive than competitive ceramic membranes due to their unique construction. With these ceramic membrane filters, it may be possible to reduce the product losses associated with traditional deashing processes at an economically attractive cost. The performance of these ceramic membrane microfilters is discussed.

  5. Performance evaluation of organic emulsion liquid membrane on phenol removal.

    Science.gov (United States)

    Ng, Y S; Jayakumar, N S; Hashim, M A

    2010-12-15

    The percentage removal of phenol from aqueous solution by emulsion liquid membrane and emulsion leakage was investigated experimentally for various parameters such as membrane:internal phase ratio, membrane:external phase ratio, emulsification speed, emulsification time, carrier concentration, surfactant concentration and internal agent concentration. These parameters strongly influence the percentage removal of phenol and emulsion leakage. Under optimum membrane properties, the percentage removal of phenol was as high as 98.33%, with emulsion leakage of 1.25%. It was also found that the necessity of carrier for enhancing phenol removal was strongly dependent on the internal agent concentration. Copyright © 2010 Elsevier B.V. All rights reserved.

  6. Separation of Gas Mixtures by New Type of Membranes – Dynamic Liquid Membranes.

    Czech Academy of Sciences Publication Activity Database

    Setničková, Kateřina; Šíma, Vladimír; Petričkovič, Roman; Řezníčková Čermáková, Jiřina; Uchytil, Petr

    2016-01-01

    Roč. 160, FEB 29 (2016), s. 132-135 ISSN 1383-5866 Institutional support: RVO:67985858 Keywords : gas separation * liquid membrane * methane Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 3.359, year: 2016

  7. Stripping of acetone from water with microfabricated and membrane gas-liquid contactors.

    Science.gov (United States)

    Constantinou, Achilleas; Ghiotto, Francesco; Lam, Koon Fung; Gavriilidis, Asterios

    2014-01-07

    Stripping of acetone from water utilizing nitrogen as a sweeping gas in co-current flow was conducted in a microfabricated glass/silicon gas-liquid contactor. The chip consisted of a microchannel divided into a gas and a liquid chamber by 10 μm diameter micropillars located next to one of the channel walls. The channel length was 35 mm, the channel width was 220 μm and the microchannel depth 100 μm. The micropillars were wetted by the water/acetone solution and formed a 15 μm liquid film between them and the nearest channel wall, leaving a 195 μm gap for gas flow. In addition, acetone stripping was performed in a microchannel membrane contactor, utilizing a hydrophobic PTFE membrane placed between two microstructured acrylic plates. Microchannels for gas and liquid flows were machined in the plates and had a depth of 850 μm and 200 μm respectively. In both contactors the gas/liquid interface was stabilized: in the glass/silicon contactor by the hydrophilic micropillars, while in the PTFE/acrylic one by the hydrophobic membrane. For both contactors separation efficiency was found to increase by increasing the gas/liquid flow rate ratio, but was not affected when increasing the inlet acetone concentration. Separation was more efficient in the microfabricated contactor due to the very thin liquid layer employed.

  8. Supported liquid inorganic membranes for nuclear waste separation

    Science.gov (United States)

    Bhave, Ramesh R; DeBusk, Melanie M; DelCul, Guillermo D; Delmau, Laetitia H; Narula, Chaitanya K

    2015-04-07

    A system and method for the extraction of americium from radioactive waste solutions. The method includes the transfer of highly oxidized americium from an acidic aqueous feed solution through an immobilized liquid membrane to an organic receiving solvent, for example tributyl phosphate. The immobilized liquid membrane includes porous support and separating layers loaded with tributyl phosphate. The extracted solution is subsequently stripped of americium and recycled at the immobilized liquid membrane as neat tributyl phosphate for the continuous extraction of americium. The sequestered americium can be used as a nuclear fuel, a nuclear fuel component or a radiation source, and the remaining constituent elements in the aqueous feed solution can be stored in glassified waste forms substantially free of americium.

  9. Preconcentration in micro-electromembrane extraction across free liquid membranes.

    Science.gov (United States)

    Kubáň, Pavel; Boček, Petr

    2014-10-27

    Preconcentration potential of micro-electromembrane extraction (μ-EME) across free liquid membrane (FLM) was examined with an anionic and a cationic dye, 4,5-dihydroxy-3-(p-sulfophenylazo)-2,7-naphthalene disulfonic acid, trisodium salt (SPADNS) and phenosafranine, respectively. For the first time, it was shown that the spatial flexibility of FLMs enabled application of tailored extraction units with mutually different shapes and migration cross-sections for FLMs, donor and acceptor solutions. Thus, e.g. conical units enabled easy and reproducible formation of a three-phase extraction system (donor/FLM/acceptor) with sub-μL volumes of acceptor solutions as well as rapid and highly efficient preconcentration of the two dyes. Quantitative measurements of resulting solutions were carried out by UV-vis spectrophotometry and enrichment factors of up to 98 were achieved for μ-EMEs of 20 μM SPADNS (50 μL) preconcentrated into 0.5 μL of pure water across 1-pentanol at -150 V for 18 min. Visual monitoring of the entire extraction process (with USB microscope camera) was possible across transparent extraction units, moreover, important extraction parameters, such as FLM dimensions and donor-to-acceptor solution volume ratio, which determine the mechanical stability of the membrane and maximum enrichment factor, respectively, were readily adjusted. Combination of μ-EME across FLMs with capillary electrophoresis (CE) was further shown suitable for preconcentration and determination of perchlorate in drinking water samples. Good repeatability of the μ-EME-CE method (RSD values better than 9.5%), linear relationship for the analytical signal vs. concentration (r(2) better than 0.997) and enrichment factors of up to 30 were achieved for μ-EMEs of perchlorate across 1-pentanol and 1-hexanol based FLMs. Copyright © 2014 Elsevier B.V. All rights reserved.

  10. High ionic liquid content polymeric gel membranes: Preparation and performance

    Czech Academy of Sciences Publication Activity Database

    Jansen, J. C.; Friess, K.; Clarizia, G.; Schauer, Jan; Izák, Pavel

    2011-01-01

    Roč. 44, č. 1 (2011), s. 39-45 ISSN 0024-9297 R&D Projects: GA ČR GA203/08/0465; GA ČR GAP106/10/1194 Institutional research plan: CEZ:AV0Z40500505; CEZ:AV0Z40720504 Keywords : ionic liquid membrane * gas separation membrane * 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide Subject RIV: CD - Macromolecular Chemistry Impact factor: 5.167, year: 2011

  11. Colloidal membranes: The rich confluence of geometry and liquid crystals

    Science.gov (United States)

    Kaplan, Cihan Nadir

    A simple and experimentally realizable model system of chiral symmetry breaking is liquid-crystalline monolayers of aligned, identical hard rods. In these materials, tuning the chirality at the molecular level affects the geometry at systems level, thereby inducing a myriad of morphological transitions. This thesis presents theoretical studies motivated by the rich phenomenology of these colloidal monolayers. High molecular chirality leads to assemblages of rods exhibiting macroscopic handedness. In the first part we consider one such geometry, twisted ribbons, which are minimal surfaces to a double helix. By employing a theoretical approach that combines liquid-crystalline order with the preferred shape, we focus on the phase transition from simple flat monolayers to these twisted structures. In these monolayers, regions of broken chiral symmetry nucleate at the interfaces, as in a chiral smectic A sample. The second part particularly focuses on the detailed structure and thermodynamic stability of two types of observed interfaces, the monolayer edge and domain walls in simple flat monolayers. Both the edge and "twist-walls" are quasi-one-dimensional bands of molecular twist deformations dictated by local chiral interactions and surface energy considerations. We develop a unified theory of these interfaces by utilizing the de Gennes framework accompanied by appropriate surface energy terms. The last part turns to colloidal "cookies", which form in mixtures of rods with opposite handedness. These elegant structures are essentially flat monolayers surrounded by an array of local, three dimensional cusp defects. We reveal the thermodynamic and structural characteristics of cookies. Furthermore, cookies provide us with a simple relation to determine the intrinsic curvature modulus of our model system, an important constant associated with topological properties of membranes. Our results may have impacts on a broader class of soft thin films.

  12. Membrane contactor assisted extraction/reaction process employing ionic liquids

    Science.gov (United States)

    Lin, Yupo J [Naperville, IL; Snyder, Seth W [Lincolnwood, IL

    2012-02-07

    The present invention relates to a functionalized membrane contactor extraction/reaction system and method for extracting target species from multi-phase solutions utilizing ionic liquids. One preferred embodiment of the invented method and system relates to an extraction/reaction system wherein the ionic liquid extraction solutions act as both extraction solutions and reaction mediums, and allow simultaneous separation/reactions not possible with prior art technology.

  13. Boron Removal in Radioactive Liquid Waste by Forward Osmosis Membrane

    International Nuclear Information System (INIS)

    Hwang, Dooseong; Choi, Hei Min; Lee, Kune Woo; Moon Jeikwon

    2014-01-01

    These wastes contain about 0.3-0.8 wt% boric acid and have been concentrated through an evaporation treatment. Boric acid tends to crystallize owing to its solubility, and to plug the evaporator. The volume reduction obtained through evaporation is limited by the amount of boric acid in the waste. As an emerging technology, forward osmosis (FO) has attracted growing interest in wastewater treatment and desalination. FO is a membrane process in which water flows across a semi-permeable membrane from a feed solution of lower osmotic pressure to a draw solution of higher osmotic pressure. However, very few studies on the removal of boron by FO have been performed. The objective of this study is to evaluate the possibility of boron separation in radioactive liquid waste by FO. In this study, the performance of FO was investigated to separate boron in the simulated liquid waste under the factors such as pH, osmotic pressure, ionic strength of the solution, and membrane characteristic. The boron separation in radioactive borate liquid waste was investigated with an FO membrane. When the feed solution containing boron is treated by the FO membrane, the boron permeation depends on the type of membrane, membrane orientation, pH of the feed solution, salt and boron concentration in the feed solution, and osmotic pressure of the draw solution. The boron flux begins to decline from pH 7, and increases with an increase in the osmotic driving force. The boron flux of the CTA-ES and ALFD membrane orientation is higher than those of the CTA-NW and ALFF orientation, respectively. The boron permeation rate is constant regardless of the osmotic pressure and membrane orientation. The boron flux decreases slightly with the salt concentration, but it is not heavily influenced at a low salt concentration

  14. Stability of Disclinations in Nematic Liquid Crystals

    International Nuclear Information System (INIS)

    Wang Yusheng; Yang Guohong; Tian Lijun; Duan Yishi

    2006-01-01

    In the light of φ-mapping method and topological current theory, the stability of disclinations around a spherical particle in nematic liquid crystals is studied. We consider two different defect structures around a spherical particle: disclination ring and point defect at the north or south pole of the particle. We calculate the free energy of these different defects in the elastic theory. It is pointed out that the total Frank free energy density can be divided into two parts. One is the distorted energy density of director field around the disclinations. The other is the free energy density of disclinations themselves, which is shown to be concentrated at the defect and to be topologically quantized in the unit of (k-k 24 )π/2. It is shown that in the presence of saddle-splay elasticity a dipole (radial and hyperbolic hedgehog) configuration that accompanies a particle with strong homeotropic anchoring takes the structure of a small disclination ring, not a point defect.

  15. RADIATION STABILITY OF NAFION MEMBRANES USED FOR ISOTOPE SEPARATION BY PROTON EXCHANGE MEMBRANE ELECTROLYSIS

    International Nuclear Information System (INIS)

    Fox, E.

    2009-01-01

    Proton Exchange Membrane Electrolyzers have potential interest for use for hydrogen isotope separation from water. In order for PEME to be fully utilized, more information is needed on the stability of Nafion when exposed to radiation. This work examines Nafion 117 under varying exposure conditions, including dose rate, total dosage and atmospheric condition. Analytical tools, such as FT-IR, ion exchange capacity, DMA and TIC-TOC were used to characterize the exposed membranes. Analysis of the water from saturated membranes can provide important data on the stability of the membranes during radiation exposure. It was found that the dose rate of exposure plays an important role in membrane degradation. Potential mechanisms for membrane degradation include peroxide formation by free radicals

  16. RADIATION STABILITY OF NAFION MEMBRANES USED FOR ISOTOPE SEPARATION BY PROTON EXCHANGE MEMBRANE ELECTROLYSIS

    Energy Technology Data Exchange (ETDEWEB)

    Fox, E

    2009-05-15

    Proton Exchange Membrane Electrolyzers have potential interest for use for hydrogen isotope separation from water. In order for PEME to be fully utilized, more information is needed on the stability of Nafion when exposed to radiation. This work examines Nafion 117 under varying exposure conditions, including dose rate, total dosage and atmospheric condition. Analytical tools, such as FT-IR, ion exchange capacity, DMA and TIC-TOC were used to characterize the exposed membranes. Analysis of the water from saturated membranes can provide important data on the stability of the membranes during radiation exposure. It was found that the dose rate of exposure plays an important role in membrane degradation. Potential mechanisms for membrane degradation include peroxide formation by free radicals.

  17. Lithium-Ion-Conducting Electrolytes: From an Ionic Liquid to the Polymer Membrane.

    Science.gov (United States)

    Fernicola, A; Weise, F C; Greenbaum, S G; Kagimoto, J; Scrosati, B; Soleto, A

    2009-05-05

    This work concerns the design, the synthesis, and the characterization of the N-butyl-N-ethylpiperidinium N,N-bis(trifluoromethane)sulfonimide (PP(24)TFSI) ionic liquid (IL). To impart Li-ion transport, a suitable amount of lithium N,N-bis-(trifluoromethane)sulfonimide (LiTFSI) is added to the IL. The Li-IL mixture displays ionic conductivity values on the order of 10(-4) S cm(-1) and an electrochemical stability window in the range of 1.8-4.5 V vs Li(+)/Li. The voltammetric analysis demonstrates that the cathodic decomposition gives rise to a passivating layer on the surface of the working electrode, which kinetically extends the stability of the Li/IL interface as confirmed by electrochemical impedance spectroscopy measurements. The LiTFSI-PP(24)TFSI mixture is incorporated in a poly(vinylidene fluoride-co-hexafluoropropylene) matrix to form various electrolyte membranes with different LiTFSI-PP(24)TFSI contents. The ionic conductivity of all the membranes resembles that of the LiTFSI-IL mixture, suggesting an ionic transport mechanism similar to that of the liquid component. NMR measurements demonstrate a reduction in the mobility of all ions following the addition of LiTFSI to the PP(24)TFSI IL and when incorporating the mixture into the membrane. Finally, an unexpected but potentially significant enhancement in Li transference number is observed in passing from the liquid to the membrane electrolyte system.

  18. Surface modification of poly(vinylidene fluoride) hollow fibre membranes for biogas purification in a gas-liquid membrane contactor system.

    Science.gov (United States)

    Jin, Pengrui; Huang, Chuan; Li, Jiaxiang; Shen, Yadong; Wang, Liao

    2017-11-01

    The wetting of hollow fibre membranes decreases the performance of the liquid-gas membrane contactor for CO 2 capture in biogas upgrading. To solve this problem, in this work, a poly(vinylidene fluoride) (PVDF) hollow fibre membrane for a liquid-gas membrane contactor was coated with a superhydrophobic layer composed of a combination of hydrophobic SiO 2 nanoparticles and polydimethylsiloxane (PDMS) by the method of spray deposition. A rough layer of SiO 2 deposited on the PVDF membrane resulted in an enhanced surface hydrophobicity. The surface structure of the pristine PVDF significantly affected the homogeneity of the generated SiO 2 layer. A uniform surface coating on the PVDF upper layer resulted from the presence of micrometre and nanometre-sized roughness on the surface of the PVDF membrane, which was achieved with a SiO 2 concentration of 4.44 mg ml -1 (0.2 g/45 ml) in the coating solution. As a result, the water contact angle of the modified surface was recorded as 155 ± 3°, which is higher than that of the pristine surface. The high contact angle is advantageous for reducing the wetting of the membrane. Additional mass transfer resistance was introduced by the superhydrophobic layer. In addition, continuous CO 2 absorption tests were carried out in original and modified PVDF hollow fibre membrane contactors, using monoethanolamine (MEA) solution as the absorbent. A long-term stability test revealed that the modified PVDF hollow fibre membrane contactor was able to outperform the original membrane contactor and demonstrated outstanding long-term stability, suggesting that spray deposition is a promising approach to obtain superhydrophobic PVDF membranes for liquid-gas membrane absorption.

  19. Description of the Gas Transport through Dynamic Liquid Membrane.

    Czech Academy of Sciences Publication Activity Database

    Uchytil, Petr; Setničková, Kateřina; Tseng, H.-H.; Šíma, Vladimír; Petričkovič, Roman

    2017-01-01

    Roč. 184, AUG 31 (2017), s. 152-157 ISSN 1383-5866 Grant - others:AV ČR(CZ) MOST-16-04 Program:Bilaterální spolupráce Institutional support: RVO:67985858 Keywords : gas separation * liquid membrane * solurion-diffusion model Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 3.359, year: 2016

  20. Preconcentration in micro-electromembrane extraction across free liquid membranes

    Czech Academy of Sciences Publication Activity Database

    Kubáň, Pavel; Boček, Petr

    2014-01-01

    Roč. 848, Oct (2014), s. 43-50 ISSN 0003-2670 R&D Projects: GA ČR(CZ) GA13-05762S Institutional support: RVO:68081715 Keywords : free liquid membranes * micro-electromembrane extraction * preconcentration Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 4.513, year: 2014

  1. Supported liquid membrane extraction of 17ß- estradiol

    African Journals Online (AJOL)

    b- estradiol and its metabolites, namely 17b-estriol and estrone in various biological matrices and water. The biological matrices in which extraction was done included bovine kidney and liver tissues, milk and urine. The liquid membrane used to trap these compounds was made of 5% tri-n-octylphosphine oxide (TOPO) ...

  2. Supported liquid membrane extraction of 17β- estradiol and its ...

    African Journals Online (AJOL)

    Administrator

    2006-10-02

    Oct 2, 2006 ... A sample purification and enrichment technique involving the use of supported liquid membrane (SLM) has been developed for the selective extraction of 17β- estradiol and its metabolites, namely 17β-estriol and estrone in various biological matrices and water. The biological matrices in which extraction ...

  3. Self-Stabilization in Membrane Systems

    Directory of Open Access Journals (Sweden)

    Artiom Alhazov

    2012-07-01

    Full Text Available In this paper we study a notion of self-stabilization, inspired from biology and engineering. Multiple variants of formalization of this notion are considered, and we discuss how such properties affect the computational power of multiset rewriting systems.

  4. Plasma membrane aquaporins mediates vesicle stability in broccoli.

    Science.gov (United States)

    Martínez-Ballesta, Maria Del Carmen; García-Gomez, Pablo; Yepes-Molina, Lucía; Guarnizo, Angel L; Teruel, José A; Carvajal, Micaela

    2018-01-01

    The use of in vitro membrane vesicles is attractive because of possible applications in therapies. Here we aimed to compare the stability and functionality of plasma membrane vesicles extracted from control and salt-treated broccoli. The impact of the amount of aquaporins was related to plasma membrane osmotic water permeability and the stability of protein secondary structure. Here, we describe for first time an increase in plant aquaporins acetylation under high salinity. Higher osmotic water permeability in NaCl vesicles has been related to higher acetylation, upregulation of aquaporins, and a more stable environment to thermal denaturation. Based on our findings, we propose that aquaporins play an important role in vesicle stability.

  5. Removal of Radioactive Pollutants by Liquid Emulsion Membrane From Liquid Waste

    International Nuclear Information System (INIS)

    Yossef, Y.A.A.

    2013-01-01

    Radioactive liquid waste should be safely managed because it is potentially hazardous to human health and the environment. Several methods were used for treatment of liquid waste, such as liquid emulsion membrane (LEM). In this work, liquid emulsion membrane using Tri-butyl phosphate (TBP) plus Bis (2-ethylhexyl) phosphate (HDEHP) as mobile carriers, hydrochloric acid (HCl) as stripping agents and an emulsifying agent (span 80) was used for the extraction of uranium ions from radioactive liquid waste. Various parameters influencing the permeation of uranium ions through the membrane have been optimized to separate uranium ions from radioactive liquid waste such as: the effects of membrane material, carrier concentration, operating conditions, etc. were examined; moreover, the transport mechanism of this uranium was also studied. The internal mass transfer in the water/oil (W/O) emulsion drop, the external mass transfer around the drop, the rates of formation, and the decomposition of the complex at the external aqueous-organic interface were considered. The results show that, the liquid emulsion membrane which consists of (25% by volume HDEHP, 0.005 M + 75% by volume TBP, 0.01 M) as extractant (carrier), span 80, 4% (v/v) (sorbitan monooleate) as surfactant agent, hydrochloric acid (HCl), (1.0 M) as stripping agent. From the results, the maximum extraction percent of uranium ions (nearly about of 100%) occurred at the operating conditions: stirring speed =500 rpm, the ratio between LEM and feed phase (liquid waste) = 20 ml: 100 ml, the ratio between organic phase (membrane phase) to internal aqueous phase (stripping phase) = 1.0 and the ph value of the external aqueous phase equal to 5.0.

  6. High temperature ceramic membrane reactors for coal liquid upgrading

    Energy Technology Data Exchange (ETDEWEB)

    Tsotsis, T.T. (University of Southern California, Los Angeles, CA (United States). Dept. of Chemical Engineering); Liu, P.K.T. (Aluminum Co. of America, Pittsburgh, PA (United States)); Webster, I.A. (Unocal Corp., Los Angeles, CA (United States))

    1992-01-01

    Membrane reactors are today finding extensive applications for gas and vapor phase catalytic reactions (see discussion in the introduction and recent reviews by Armor [92], Hsieh [93] and Tsotsis et al. [941]). There have not been any published reports, however, of their use in high pressure and temperature liquid-phase applications. The idea to apply membrane reactor technology to coal liquid upgrading has resulted from a series of experimental investigations by our group of petroleum and coal asphaltene transport through model membranes. Coal liquids contain polycyclic aromatic compounds, which not only present potential difficulties in upgrading, storage and coprocessing, but are also bioactive. Direct coal liquefaction is perceived today as a two-stage process, which involves a first stage of thermal (or catalytic) dissolution of coal, followed by a second stage, in which the resulting products of the first stage are catalytically upgraded. Even in the presence of hydrogen, the oil products of the second stage are thought to equilibrate with the heavier (asphaltenic and preasphaltenic) components found in the feedstream. The possibility exists for this smaller molecular fraction to recondense with the unreacted heavy components and form even heavier undesirable components like char and coke. One way to diminish these regressive reactions is to selectively remove these smaller molecular weight fractions once they are formed and prior to recondensation. This can, at least in principle, be accomplished through the use of high temperature membrane reactors, using ceramic membranes which are permselective for the desired products of the coal liquid upgrading process. An additional incentive to do so is in order to eliminate the further hydrogenation and hydrocracking of liquid products to undesirable light gases.

  7. Stability and Degradation Mechanisms of Radiation-Grafted Polymer Electrolyte Membranes for Water Electrolysis.

    Science.gov (United States)

    Albert, Albert; Lochner, Tim; Schmidt, Thomas J; Gubler, L

    2016-06-22

    Radiation-grafted membranes are a promising alternative to commercial membranes for water electrolyzers, since they exhibit lower hydrogen crossover and area resistance, better mechanical properties, and are of potentially lower cost than perfluoroalkylsulfonic acid membranes, such as Nafion. Stability is an important factor in view of the expected lifetime of 40 000 h or more of an electrolyzer. In this study, combinations of styrene (St), α-methylstyrene (AMS), acrylonitrile (AN), and 1,3-diisopropenylbenzene (DiPB) are cografted into 50 μm preirradiated poly(ethylene-co-tetrafluoroethylene) (ETFE) base film, followed by sulfonation to produce radiation-grafted membranes. The stability of the membranes with different monomer combinations is compared under an accelerated stress test (AST), and the degradation mechanisms are investigated. To mimic the conditions in an electrolyzer, in which the membrane is always in contact with liquid water at elevated temperature, the membranes are immersed in water for 5 days at 90 °C, so-called thermal stress test (TST). In addition to testing in air atmosphere tests are also carried out under argon to investigate the effect of the absence of oxygen. The water is analyzed with UV-vis spectroscopy and ion chromatography. The ion exchange capacity (IEC), swelling degree, and Fourier transform infrared (FTIR) spectra of the membranes are compared before and after the test. Furthermore, energy-dispersive X-ray (EDX) spectroscopic analysis of the membrane cross-section is performed. Finally, the influence of the TST to the membrane area resistance and hydrogen crossover is measured. The stability increases along the sequence St/AN, St/AN/DiPB, AMS/AN, and AMS/AN/DiPB grafted membrane. The degradation at the weak-link, oxygen-induced degradation, and hydrothermal degradation are proposed in addition to the "swelling-induced detachment" reported in the literature. By mitigating the possible paths of degradation, the AMS

  8. Hollow fiber membrane contactor as a gas-liquid model contactor

    OpenAIRE

    Dindore, V. Y.; Brilman, D. W. F.; Versteeg, G. F.

    2005-01-01

    Microporous hollow fiber gas-liquid membrane contactors have a fixed and well-defined gas-liquid interfacial area. The liquid flow through the hollow fiber is laminar, thus the liquid side hydrodynamics are well known. This allows the accurate calculation of the fiber side physical mass transfer coefficient from first principles. Moreover, in the case of gas-liquid membrane contactor, the gas-liquid exposure time can be varied easily and independently without disturbing the gas-liquid interfa...

  9. Use of membrane separation processes for the separation of radionuclides from liquid and gas streams

    International Nuclear Information System (INIS)

    Vladisavljevic, G.T.; Rajkovic, M.B.

    1999-01-01

    Use of membranes for the separation and recovery of radionuclides from contaminated liquid and gas streams has been discussed in this paper. The special attention has been paid to the use of ion-exchange membranes for electrodialysis and Donnan dialysis, as well as the use of facilitated liquid membranes for liquid pertraction. (author)

  10. In vitro antioxidant and membrane stabilization activities of the fruit ...

    African Journals Online (AJOL)

    Arthritis is an inflammation of one or more joints. There is considerable experimental evidence linking lysosomal enzymes with tissue damage in arthritis. This study investigated anti-arthritic properties of Tetrapleura tetraptera (TT) using membrane stabilization assay (MSA). Powdered TT fruit sample was extracted by ...

  11. Salinity induced changes in cell membrane stability, protein and ...

    African Journals Online (AJOL)

    control), 4.7, 9.4 and 14.1 dS m-1 to determine the effect of salt on vegetative growth, relative water content, cell membrane stability, protein and RNA contents in sand culture experiment. Fresh and dry weights of plants, shoots and roots decreased ...

  12. Multi-responsive ionic liquid emulsions stabilized by microgels

    NARCIS (Netherlands)

    Monteillet, H.; Workamp, M.; Li, X.; Schuur, Boelo; Kleijn, J.M.; Leermakers, F.; Sprakel, J.

    2014-01-01

    We present a complete toolbox to use responsive ionic liquid (IL) emulsions for extraction purposes. IL emulsions stabilized by responsive microgels are shown to allow rapid extraction and reversible breaking and re-emulsification. Moreover, by using a paramagnetic ionic liquid, droplets can be

  13. Surface Modifications of Support Partitions for Stabilizing Biomimetic Membrane Arrays

    DEFF Research Database (Denmark)

    Perry, Mark; Hansen, Jesper Schmidt; Jensen, Karin Bagger Stibius

    2011-01-01

    Black lipid membrane (BLM) formation across apertures in an ethylene tetra-fluoroethylene (ETFE) partition separating two aqueous compartments is an established technique for the creation of biomimetic membranes. Recently multi-aperture BLM arrays have attracted interest and in order to increase...... with a high signal-to-noise (s/n) ratio. We demonstratesd this by reconstituting gA and α-hemolysin (α-HL) into BLM arrays. The improvement in membrane array lifetime and s/n ratio demonstrates that surface plasma polymerization of the supporting partition can be used to increase the stability of biomimetic...... modified partitions were similar and significantly lower than for arrays formed using untreated ETFE partitions. For single side n-hexene modification average membrane array lifetimes were not significantly changed compared to untreated ETFE. Double-sided n-hexene modification greatly improved average...

  14. Uranium Extraction From Artificial Liquid Waste Using Continuous Extraction Liquid membrane Technique

    International Nuclear Information System (INIS)

    Rusdianasari; Buchari

    2002-01-01

    The continuous extraction of uranium from artificial liquid waste by emulsion liquid membrane was carried out using one stage mixer-settler. This emulsion liquid membrane containing di-2-ethylhexylphosphoric acid (D2EHPA) and tri-n-buthyl phosphate (TBP) as carrier were carried out using one stage mixer-settler. The optimum condition gave the ratio of emulsion velocity to the feed velocity 1:4 and steady state reached after five minutes. The optimum condition was obtained at the 90.91 % of uranium recovered from raffinate, using EDTA as the masking agent with concentration 5x10 - 2 M . The total concentration of carrier was 3% with ratio D2EHPA and TBP 3:1. The emulsion liquid membrane has high relative selectivity after steady state with separation factors were α U , N i= 115,43 and α U , Fe 328,55. The result of experiment showed that emulsion liquid membrane containing D2EHPA and TBP as carrier have good performance for continuous system

  15. Liquid crystalline polymer electrolyte membranes with ion gating properties

    Science.gov (United States)

    Cao, Jinwei; Piedrahita, Camilo; Koterasawa, Kagami; Freedman, Abegel; Martins, Juliana; Kyu, Thein; Pugh, Coleen; Adachi, Kaoru; Tsukahara, Yasuhisa

    Polymer electrolyte membranes (PEMs) with ion conducting channels have been fabricated via photo-polymerization of liquid crystalline monomers, synthesized in our laboratory. The monomers consist of polyethylene glycol segments as the ion conduction medium and photoactive azobenzene mesogen. Guided by the phase diagram of azobenzene LC and nematic LC, ion conducting channels are formed in the liquid crystalline phases. Ionic conductivities of the azobenzene LCs were measured in trans-state and cis-state using AC impedance spectroscopy. By applying UV or visible light, the opening/closing of ion channels may be controlled through rapid trans-cis isomerization of azobenzene mesogen by light irradiation. Therefore, the ion conduction ability of the PEMs can be optically controlled, affording ion gating capability of the PEMs. These PEMs can act as the ion conducting channels on cell membranes and, therefore, may be used to construct artificial neurons. Supported by NSF-DMR 1502543.

  16. Research News: Emulsion Liquid Membrane Extraction in a Hollow-Fiber Contactor

    Science.gov (United States)

    Wiencek, John M.; Hu, Shih-Yao

    2000-01-01

    This article describes how ELMs (emulsion liquid membranes) can be used for extraction. The article addresses the disadvantages of ELM extraction in a stirred contactor, and the advantages of SELMs (supported emulsion liquid membranes). The introduction of the article provides background information on liquid-liquid solvent extraction and dispersion-free solvent extraction.

  17. Stability of solids-coated liquid layers between bubbles

    International Nuclear Information System (INIS)

    Ali, S A.; Gauglitz, Phillip A.; Rossen, W R.

    1999-01-01

    In principle, liquid layers between bubbles can be stabilized by a coating of fine solid particles even in the absence of surface-active agents in the liquid. Theoretical modeling of a two-dimensional liquid layer between bubbles containing one row of solid particles suggests that in three dimensions such a layer would unstable unless the solids all touch. This hints at a possible mechanism for bubble stabilization and subsequent rupture in the waste stored in underground tanks at the Hanford nuclear reservation

  18. Ionic Liquid Membranes for Carbon Dioxide-Methane Separation

    Czech Academy of Sciences Publication Activity Database

    Uchytil, Petr; Schauer, Jan; Petričkovič, Roman; Setničková, Kateřina; Suen, S.Y.

    2011-01-01

    Roč. 383, 1-2 (2011), s. 262-271 ISSN 0376-7388 R&D Projects: GA ČR GA104/09/1165; GA ČR GCP106/10/J038; GA MŠk ME 889 Institutional research plan: CEZ:AV0Z40720504; CEZ:AV0Z40500505 Keywords : ionic liquid membrane * gas separation * gas transport Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 3.850, year: 2011

  19. Description of the Gas Transport through Dynamic Liquid Membrane.

    Czech Academy of Sciences Publication Activity Database

    Uchytil, Petr; Setničková, Kateřina; Tseng, H.-H.; Šíma, Vladimír; Petričkovič, Roman

    2017-01-01

    Roč. 184, AUG 31 (2017), s. 152-157 ISSN 1383-5866 Grant - others:AV ČR(CZ) MOST-16-04 Program:Bilaterální spolupráce Institutional support: RVO:67985858 Keywords : gas separation * liquid membrane * solurion-diffusion model Subject RIV: CI - Industrial Chemistry, Chemical Engineering OBOR OECD: Chemical process engineering Impact factor: 3.359, year: 2016

  20. Development of robust fluorinated TiO2/PVDF composite hollow fiber membrane for CO2 capture in gas-liquid membrane contactor

    Science.gov (United States)

    Lin, Yuqing; Xu, Yilin; Loh, Chun Heng; Wang, Rong

    2018-04-01

    Gas-liquid membrane contactor (GLMC) is a promising method to attain high efficiency for CO2 capture from flue gas, biogas and natural gas. However, membranes used in GLMC are prone to pore wetting due to insufficient hydrophobicity and low chemical resistance, resulting in significant increase in mass transfer resistance. To mitigate this issue, inorganic-organic fluorinated titania/polyvinylidene fluoride (fTiO2/PVDF) composite hollow fiber (HF) membranes was prepared via facile in-situ vapor induced hydrolyzation method, followed by hydrophobic modification. The proposed composite membranes were expected to couple the superb chemical stability of inorganic and high permeability/low cost of organic materials. The continuous fTiO2 layer deposited on top of PVDF substrate was found to possess a tighter microstructure and better hydrophobicity, which effectively prevented the membrane from wetting and lead to a high CO2 absorption flux (12.7 × 10-3 mol m-2 s-1). In a stability test with 21-day operation of GLMC using 1M monoethanolamine (MEA) as the absorbent, the fTiO2/PVDF membrane remained to be intact with a CO2 absorption flux decline of ∼16%, while the pristine PVDF membrane suffered from a flux decline of ∼80% due to membrane damage. Overall, this work provides an insight into the preparation of high-quality inorganic/organic composite HF membranes for CO2 capture in GLMC application.

  1. Faradaically selective membrane for liquid metal displacement batteries

    Science.gov (United States)

    Yin, Huayi; Chung, Brice; Chen, Fei; Ouchi, Takanari; Zhao, Ji; Tanaka, Nobuyuki; Sadoway, Donald R.

    2018-02-01

    In the realm of stationary energy storage, a plurality of candidate chemistries continues to vie for acceptance, among them the Na-NiCl2 displacement battery, which has eluded widespread adoption owing to the fragility of the β″-Al2O3 membrane. Here we report a porous electronically conductive membrane, which achieves chemical selectivity by preferred faradaic reaction instead of by regulated ionic conduction. Fitted with a porous membrane of TiN, a displacement cell comprising a liquid Pb positive electrode, a liquid Li-Pb negative electrode and a molten-salt electrolyte of PbCl2 dissolved in LiCl-KCl eutectic was cycled at a current density of 150 mA cm-2 at a temperature of 410 °C and exhibited a coulombic efficiency of 92% and a round-trip energy efficiency of 71%. As an indication of industrial scalability, we show comparable performance in a cell fitted with a faradaic membrane fashioned out of porous metal.

  2. Structuring detergents for extracting and stabilizing functional membrane proteins.

    Directory of Open Access Journals (Sweden)

    Rima Matar-Merheb

    Full Text Available BACKGROUND: Membrane proteins are privileged pharmaceutical targets for which the development of structure-based drug design is challenging. One underlying reason is the fact that detergents do not stabilize membrane domains as efficiently as natural lipids in membranes, often leading to a partial to complete loss of activity/stability during protein extraction and purification and preventing crystallization in an active conformation. METHODOLOGY/PRINCIPAL FINDINGS: Anionic calix[4]arene based detergents (C4Cn, n=1-12 were designed to structure the membrane domains through hydrophobic interactions and a network of salt bridges with the basic residues found at the cytosol-membrane interface of membrane proteins. These compounds behave as surfactants, forming micelles of 5-24 nm, with the critical micellar concentration (CMC being as expected sensitive to pH ranging from 0.05 to 1.5 mM. Both by 1H NMR titration and Surface Tension titration experiments, the interaction of these molecules with the basic amino acids was confirmed. They extract membrane proteins from different origins behaving as mild detergents, leading to partial extraction in some cases. They also retain protein functionality, as shown for BmrA (Bacillus multidrug resistance ATP protein, a membrane multidrug-transporting ATPase, which is particularly sensitive to detergent extraction. These new detergents allow BmrA to bind daunorubicin with a Kd of 12 µM, a value similar to that observed after purification using dodecyl maltoside (DDM. They preserve the ATPase activity of BmrA (which resets the protein to its initial state after drug efflux much more efficiently than SDS (sodium dodecyl sulphate, FC12 (Foscholine 12 or DDM. They also maintain in a functional state the C4Cn-extracted protein upon detergent exchange with FC12. Finally, they promote 3D-crystallization of the membrane protein. CONCLUSION/SIGNIFICANCE: These compounds seem promising to extract in a functional state

  3. Solar assisted liquid desiccant cooling using clay based membranes

    Directory of Open Access Journals (Sweden)

    Priya S. Shanmuga

    2018-01-01

    Full Text Available The environmental concerns have led to the urge of the usage of non-conventional energy resources like solar, wind, thermal, geothermal etc. which provide enormous source of energy without causing any further diminution of the environment. Instead of the conventional HVAC systems that cause colossal environmental perils, usage of liquid desiccants in coming in vogue whereby reducing ecological threats. Moreover, solar assisted systems provide further impulse to such systems. This paper discusses about the various comparisons between liquid desiccants: Lithium chloride, Potassium formate and Calcium chloride and concludes that potassium formate is the best desiccant to be used among the three. Potassium formate (HCOOK is used which is cheaper and less corrosive as compared to the other aqueous salts, and has a negative crystallization temperature. Potassium formate is a new liquid desiccant and thus, not much research is available currently. The weather conditions of Manipal provide an appropriate condition for the experimentations of solar aided liquid desiccant evaporative cooling systems due to its humid climate and intense solar radiation obtained. The small scale experimentation also encounters the problem of liquid desiccant carryover by the air flow, with the help of clay based membranes which are again cheap, environmentally benign and obtained in a facile way. The projected system takes complete advantage of pure solar energy aimed at the regeneration of liquid desiccant.

  4. Mercury Concentration Reduction In Waste Water By Using Liquid Surfactant Membrane Technique

    International Nuclear Information System (INIS)

    Prayitno; Sardjono, Joko

    2000-01-01

    The objective of this research is ti know effectiveness of liquid surfactant membrane in diminishing mercury found in waste water. This process can be regarded as transferring process of solved mercury from the external phase functioning as a moving phase to continue to the membrane internal one. The existence of the convection rotation results in the change of the surface pressure on the whole interface parts, so the solved mercury disperses on every interface part. Because of this rotation, the solved mercury will fulfil every space with particles from dispersion phase in accordance with its volume. Therefore, the change of the surface pressure on the whole interface parts can be kept stable to adsorb mercury. The mercury adsorbed in the internal phase moves to dispersed particles through molecule diffusion process. The liquid surfactant membrane technique in which the membrane phase is realized into emulsion contains os kerosene as solvent, sorbitan monoleat (span-80) 5 % (v/v) as surfactant, threbuthyl phosphate (TBP) 10 % (v/v) as extractant, and solved mercury as the internal phase. All of those things are mixed and stirred with 8000 rpm speed for 20 minutes. After the stability of emulsion is formed, the solved mercury is extracted by applying extraction process. The effective condition required to achieve mercury ion recovery utilizing this technique is obtained through extraction and re-extraction process. This process was conducted in 30 minutes with membrane and mercury in scale 1 : 1 on 100 ppm concentration. The results of the processes was 99,6 % efficiency. This high efficiency shows that the liquid surfactant membrane technique is very effective to reduce waste water contamined by mercury

  5. highly selective amino acid salt solutions as absorption liquid for CO(2) capture in gas-liquid membrane contactors.

    Science.gov (United States)

    Simons, Katja; Nijmeijer, Kitty; Mengers, Harro; Brilman, Wim; Wessling, Matthias

    2010-08-23

    The strong anthropogenic increase in the emission of CO(2) and the related environmental impact force the developments towards sustainability and carbon capture and storage (CCS). In the present work, we combine the high product yields and selectivities of CO(2) absorption processes with the advantages of membrane technology in a membrane contactor for the separation of CO(2) from CH(4) using amino acid salt solutions as competitive absorption liquid to alkanol amine solutions. Amino acids, such as sarcosine, have the same functionality as alkanol amines (e.g., monoethanolamine=MEA), but in contrast, they exhibit a better oxidative stability and resistance to degradation. In addition, they can be made nonvolatile by adding a salt functionality, which significantly reduces the liquid loss due to evaporation at elevated temperatures in the desorber. Membrane contactor experiments using CO(2)/CH(4) feed mixtures to evaluate the overall process performance, including a full absorption/desorption cycle show that even without a temperature difference between absorber and desorber, a CO(2)/CH(4) selectivity of over 70 can be easily achieved with the sarcosine salt solution as absorption liquid. This selectivity reaches values of 120 at a temperature difference between absorber and desorber of 35 degrees C, compared to a value of only 60 for MEA under the same conditions. Although CO(2) permeance values are somewhat lower than the values obtained for MEA, the results clearly show the potential of amino acid salt solutions as competitive absorption liquids for the energy efficient removal of CO(2). In addition, due to the low absorption of CH(4) in sarcosine compared to MEA, the loss of CH(4) is reduced and significantly higher CH(4) product yields can be obtained.

  6. High flux, positively charged loose nanofiltration membrane by blending with poly (ionic liquid) brushes grafted silica spheres

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Liang [School of Chemical Engineering and Energy, Zhengzhou University, Zhengzhou 450001 (China); Zhang, Yatao, E-mail: zhangyatao@zzu.edu.cn [School of Chemical Engineering and Energy, Zhengzhou University, Zhengzhou 450001 (China); UNESCO Center for Membrane Science and Technology, School of Chemical Engineering, University of New South Wales, Sydney, NSW 2052 (Australia); Wang, Yuanming; Zhang, Haoqin [School of Chemical Engineering and Energy, Zhengzhou University, Zhengzhou 450001 (China); Liu, Jindun, E-mail: liujindun@zzu.edu.cn [School of Chemical Engineering and Energy, Zhengzhou University, Zhengzhou 450001 (China)

    2015-04-28

    Highlights: • SiO{sub 2} spheres were modified by poly (ionic liquid) brushes via RATRP. • Positively charged NF membranes were fabricated by incorporation of SiO{sub 2}-PIL. • The membranes exhibited higher rejection for dyes and superior penetration for salts. - Abstract: Silica spheres modified by poly (ionic liquid) brushes, a novel positively charged nanomaterial is prepared by atom transfer radical polymerization (ATRP). A high flux positively charged loose nanofiltration membrane is fabricated via “blending-phase inversion” method. The morphology structures, hydrophilicity, thermal and mechanical properties, permeation performance of these membranes are investigated in detail. The results reveal that the hybrid membranes have enhanced surface hydrophilicity, water permeability, thermal stability, and mechanical properties. Characterization of membrane separation properties shows that the hybrid membranes possess higher salt permeability and relatively higher rejection for reactive dyes, which may open opportunities for the recycling of reactive dyes wastewater. Moreover, such hybrid membranes have an outstanding operational stability and salts concentration showed little effect on the separation properties.

  7. Fundamental Study of Sorption of Pure Liquids and Liquid Mixtures into Polymeric Membrane

    Czech Academy of Sciences Publication Activity Database

    Randová, A.; Bartovská, L.; Friess, K.; Hovorka, Š.; Izák, Pavel

    2014-01-01

    Roč. 61, DEC 2014 (2014), s. 64-71 ISSN 0014-3057 R&D Projects: GA ČR(CZ) GAP106/12/0569 Institutional support: RVO:67985858 Keywords : organic liquids * gravimetric sorption * flat polymer membrane Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 3.005, year: 2014

  8. Enhanced Gas Separation through Nanoconfined Ionic Liquid in Laminated MoS2 Membrane.

    Science.gov (United States)

    Chen, Danke; Ying, Wen; Guo, Yi; Ying, Yulong; Peng, Xinsheng

    2017-12-20

    Two-dimensional (2D) materials-based membranes show great potential for gas separation. Herein an ionic liquid, 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM][BF 4 ]), was confined in the 2D channels of MoS 2 -laminated membranes via an infiltration process. Compared with the corresponding bulk [BMIM][BF 4 ], nanoconfined [BMIM][BF 4 ] shows an obvious incremental increase in freezing point and a shift of vibration bands. The resulting MoS 2 -supported ionic liquid membrane (MoS 2 SILM) exhibits excellent CO 2 separation performance with high CO 2 permeance (47.88 GPU) and superb selectivity for CO 2 /N 2 (131.42), CO 2 /CH 4 (43.52), and CO 2 /H 2 (14.95), which is much better than that of neat [BMIM][BF 4 ] and [BMIM][BF 4 ]-based membranes. The outstanding performance of MoS 2 SILMs is attributed to the nanoconfined [BMIM][BF 4 ], which enables fast transport of CO 2 . Long-term operation also reveals the durability and stability of the prepared MoS 2 SILMs. The method of confining ILs in the 2D nanochannels of 2D materials may pave a new way for CO 2 capture and separation.

  9. Cleaning of liquid LLW from decontamination processes using semipermeable membranes

    International Nuclear Information System (INIS)

    Dulama, M.; Deneanu, N.; Pavelescu, M.

    2003-01-01

    Of the three processes, which have been used extensively for liquid radioactive waste purification, evaporation and ion exchange are costly and flocculation gives a low degree of purification. By comparison to that, reverse osmosis offers intermediate purification at reasonable cost. Present research is examining the potential of using a membrane filtration system for the removal of dissolved radionuclides, but chemical treatment showed as necessary to convert soluble radionuclides, organic traces and metals to insoluble, filterable species. Liquid wastes within a CANDU station are segregated into normal and low-activity waste streams. The normal-activity waste includes wastes from the laboratories, laundries, some service-building drains, upgrade drains, and decontamination center. The drains from the reactor building, the heavy-water area, the spent-fuel pool, and the resin storage area are also directed to this normal activity wastes from showers and building drains in areas of the service building that would not normally be contaminated. The aqueous liquid wastes from the decontamination center and the other collected wastes from the chemical drain system are currently treated by the membrane plant. Generally, the liquid waste streams are effectively volume-reduced by a combination of continuous crossflow microfiltration (MF), spiral wound reverse osmosis (SWRO) and tubular reverse osmosis membrane technologies. Backwash chemical cleaning wastes from the membrane plant are further volume-reduced by evaporation. The concentrate from the membrane plant is ultimately immobilized with bitumen. The ability of the MF/SWRO technology to remove impurities non-selectively makes it suitable for the treatment of radioactive effluents from operating nuclear plants, with proper membrane selection, feed characterization, system configuration and system chemistry control. The choice of polysulfonate material for membrane was based on the high flow rates achievable with this

  10. Liquidity and Stability of Agriculture in the Czech Republic

    Directory of Open Access Journals (Sweden)

    Lánský J.

    2017-09-01

    Full Text Available This article is based on empirical research and 2007–2012 statistical data from joint stock companies which were active in the agriculture sector of the Czech Republic. It deals with the wider aspects of liquidity and stability using suitable liquidity indicators and a vertical financial analysis over a sufficient period of time providing valid results for assessing liquidity and stability of agriculture in relation to cyclic fluctuations. The vertical financial analysis was performed to determine the liquidity structure at current assets and short term debts. Then convenient indicators of current ratio, quick ratio, and cash ratio were applied and interpreted in relation to cyclical deviations and agriculture specifics. From the viewpoint of liquidity measured using the current ratio, agriculture in the Czech Republic is stable and the current ratio values bear witness to solid liquidity, whereby the short-term assets exceed the short-term external funds. Research is to show whether the agriculture sector is liquid and whether the liquidity indicators provide the basis for solvency in the given field.

  11. Electrohydrodynamic Stability of a Liquid Bridge: The "ALEX" Experiment

    Science.gov (United States)

    Burcham, C. L.; Sanakaran, S.; Saville, D. A.

    1999-01-01

    To provide insight into the roles of electrical forces, experiments on the stability of a liquid bridge were carried out during the 1996 Life And Microgravity Science Mission on the space shuttle Columbia. In terrestrial laboratories a Plateau configuration (where the bridge is surrounded by a matched density liquid) is necessary to avoid deformation due to buoyancy. This complicates the electrical boundary conditions, since charge is transported across the liquid-liquid interface. In the microgravity environment, a cylindrical bridge can be deployed in a gas which considerably simplifies the boundary condition. Nevertheless, to provide a tie-in to terrestrial experiments, two-phase experiments were carried out. The agreement with previous work was excellent. Then several experiments were conducted with a bridge deployed in a dielectric gas, SF6. In experiments with steady fields, it was found that the bridge was less stable than predicted by a linearized stability analysis using the Taylor-Melcher leaky dielectric model.

  12. A Review of Polymer-Stabilized Ferroelectric Liquid Crystals

    OpenAIRE

    Dierking, Ingo

    2014-01-01

    The polymer stabilized state of ferroelectric liquid crystals (FLC) is reviewed; and the effect of a dispersed polymer network in an FLC outlined and discussed. All fundamental material aspects are demonstrated; such as director tilt angle; spontaneous polarization; response time and viscosity; as well as the dielectric modes. It was found that the data can largely be explained by assuming an elastic interaction between the polymer network strands and the liquid crystal molecules. The elastic...

  13. Evaluation of nanofiltration membranes for treatment of liquid radioactive waste

    International Nuclear Information System (INIS)

    Oliveira, Elizabeth Eugenio de Mello

    2013-01-01

    The physicochemical behavior of two nanofiltration membranes for treatment of a low-level radioactive liquid waste (carbonated water) was investigated through static, dynamic and concentration tests. This waste was produced during conversion of uranium hexafluoride (UF 6 ) to uranium dioxide (UO 2 ) in the cycle of nuclear fuel. This waste contains about 7.0 mg L -1 of uranium and cannot be discarded to the environment without an adequate treatment. In static tests membrane samples were immersed in the waste for 24 to 5000 h. Their transport properties (hydraulic permeability, permeate flux, sulfate and chloride ions rejection) were evaluated before and after immersion in the waste using a permeation flux front system under 0.5 MPa. The selective layer (polyamide) was characterized by zeta potential, contact angle, scanning electron microscopy for field emission, atomic force microscopy, infrared spectroscopy, x-ray fluorescence and thermogravimetric analysis before and after static tests. In dynamic tests the waste was permeated under 0.5 MPa, and the membranes showed rejection to uranium above 85% were obtained. The short-term static tests (24-72 h) showed that the selective layer and surface charge of the membranes were not chemical changed, according infrared spectra data. After 5000 h a coating layer was released from the membranes, poly(vinyl alcohol), PVA. After this loss the rejection for uranium decreased. Permeation and concentration of the waste were carried out in permeation flux tangential system under 1.5 MPa. The rejection of uranium was around 90% for permeation tests. In concentration tests the permeated was collected continuously until about 80% reduction of the feed volume. The rejection of uranium was of the 97%. The nanofiltration membranes tested were efficient to concentrate the uranium from the waste. (author)

  14. Hollow fiber gas-liquid membrane contactors for acid gas capture: a review.

    Science.gov (United States)

    Mansourizadeh, A; Ismail, A F

    2009-11-15

    Membrane contactors using microporous membranes for acid gas removal have been extensively reviewed and discussed. The microporous membrane acts as a fixed interface between the gas and the liquid phase without dispersing one phase into another that offers a flexible modular and energy efficient device. The gas absorption process can offer a high selectivity and a high driving force for transport even at low concentrations. Using hollow fiber gas-liquid membrane contactors is a promising alternative to conventional gas absorption systems for acid gas capture from gas streams. Important aspects of membrane contactor as an efficient energy devise for acid gas removal including liquid absorbents, membrane characteristics, combination of membrane and absorbent, mass transfer, membrane modules, model development, advantages and disadvantages were critically discussed. In addition, current status and future potential in research and development of gas-liquid membrane contactors for acid gas removal were also briefly discussed.

  15. Foam films as thin liquid gas separation membranes.

    Science.gov (United States)

    Ramanathan, Muruganathan; Müller, Hans Joachim; Möhwald, Helmuth; Krastev, Rumen

    2011-03-01

    In this letter, we testify the feasibility of using freestanding foam films as a thin liquid gas separation membrane. Diminishing bubble method was used as a tool to measure the permeability of pure gases like argon, nitrogen, and oxygen in addition to atmospheric air. All components of the foam film including the nature of the tail (fluorocarbon vs hydrocarbon), charge on the headgroup (anionic, cationic, and nonionic) and the thickness of the water core (Newton black film vs Common black film) were systematically varied to understand the permeation phenomena of pure gases. Overall results indicate that the permeability values for different gases are in accordance with magnitude of their molecular diameter. A smaller gaseous molecule permeates faster than the larger ones, indicating a new realm of application for foam films as size selective separation membranes.

  16. New absorption liquids for the removal of CO2 from dilute gas streams using membrane contactors

    NARCIS (Netherlands)

    Kumar, P.S.; Hogendoorn, J.A.; Feron, P.H.M.; Versteeg, G.F.

    2002-01-01

    A new absorption liquid based on amino acid salts has been studied for CO2 removal in membrane gas–liquid contactors. Unlike conventional gas treating solvents like aqueous alkanolamines solutions, the new absorption liquid does not wet polyolefin microporous membranes. The wetting characteristics

  17. New absorption liquids for the removal of CO2 from dilute gas streams using membrane contactors

    NARCIS (Netherlands)

    Kumar, P.S.; Hogendoorn, J.A.; Feron, P.H.M.; Versteeg, G.F.

    2002-01-01

    A new absorption liquid based on amino acid salts has been studied for CO2 removal in membrane gas-liquid contractors. Unlike conventional gas treating solvents like aqueous alkanolamines solutions, the new absorption liquid does not wet polyolefin microporous membranes. The wetting characteristics

  18. Passive Temperature Stabilization of Silicon Photonic Devices Using Liquid Crystals

    Directory of Open Access Journals (Sweden)

    Joanna Ptasinski

    2014-03-01

    Full Text Available In this work we explore the negative thermo-optic properties of liquid crystal claddings for passive temperature stabilization of silicon photonic integrated circuits. Photonic circuits are playing an increasing role in communications and computing, but they suffer from temperature dependent performance variation. Most existing techniques aimed at compensation of thermal effects rely on power hungry Joule heating. We show that integrating a liquid crystal cladding helps to minimize the effects of a temperature dependent drift. The advantage of liquid crystals lies in their high negative thermo-optic coefficients in addition to low absorption at the infrared wavelengths.

  19. Liquid-liquid extraction of uranium(VI) in the system with a membrane contactor.

    Science.gov (United States)

    Biełuszka, Paweł; Zakrzewska, Grażyna; Chajduk, Ewelina; Dudek, Jakub

    Raising role of the nuclear power industry, including governmental plans for the construction of first nuclear power plant in Poland, creates increasing demand for the uranium-based nuclear fuels. The project implemented by Institute of Nuclear Chemistry and Technology concerns the development of effective methods for uranium extraction from low-grade ores and phosphorites for production of yellow cake-U 3 O 8 . The Liqui-Cel ® Extra-Flow 2.5 × 8 Membrane Contactor produced by CELGARD LLC (Charlotte, NC) company is the main component of the installation for liquid-liquid extraction applied for processing of post leaching liquors. In the process of membrane extraction the uranyl ions from aqueous phase are transported through the membrane into organic phase. The flow of two phases in the system was arranged in co-current mode. The very important element of the work was a selection of extracting agents appropriate for the membrane process. After preliminary experiments comprising tests of membrane resistivity and determination of extraction efficiency, di(2-ethylhexyl)phosphoric acid was found to be most favourable. An important aspect of the work was the adjustment of hydrodynamic conditions in the capillary module. To avoid the membrane wettability by organic solvent and mixing two phases equal pressure drops along the membrane module to minimize the transmembrane pressure, were assumed. Determination of pressure drop along the module was conducted using Bernoulli equation. The integrated process of extraction/re-extraction conducted in continuous mode with application of two contactors was designed.

  20. Extraction of Penicillin V from Simulated Fermentation Broth by Liquid-Liquid Membrane Technique

    OpenAIRE

    Khalid W. Hameed

    2012-01-01

    Liquid-liquid membrane extraction technique, pertraction, using three types of solvents (methyl isobutyl ketone, n-butyl acetate, and n-amyl acetate) was used for recovery of penicillin V from simulated fermentation broth under various operating conditions of pH value (4-6) for feed and (6-8) for receiver phase, time (0-40 min), and agitation speed (300-500 rpm) in a batch laboratory unit system. The optimum conditions for extraction were at pH of 4 for feed, and 8 for receiver phase, rotatio...

  1. A series of poly(butylimidazolium) ionic liquid functionalized copolymers for anion exchange membranes

    Science.gov (United States)

    Ouadah, Amina; Xu, Hulin; Luo, Tianwei; Gao, Shuitao; Wang, Xing; Fang, Zhou; Jing, Chaojun; Zhu, Changjin

    2017-12-01

    A new series of ionic liquid functionalized copolymers for anion exchange membranes (AEM) is prepared. Poly(butylvinylimidazolium)(b-VIB) is copolymerized with para-methyl styrene (p-MS) by the radical polymerization formed block copolymers b-VIB/p-MS, which is crosslinked with poly(diphenylether bibenzimidazole) (DPEBI) providing the desired materials b-VIB/p-MS/DPEBI. Structures are characterized via H1NMR, FTIR spectra and elemental analysis. The b-VIB blocks offer the anion conduction function while DPEBI moieties contribute to enhancing other properties. The prepared membranes display chloride conductivity as high as 19.5 mS/cm at 25 °C and 69.2 mS/cm at 100 °C-higher than that of the commercial membrane tokuyuama A201-. Their hydroxide conductivity reaches 35.7 Scm-1 at 25 °C and 73.1 Scm-1 at 100 °C. The membranes showed a linear Arrhenius behavior in the anion conduction, low activation energies and distinguished nanophase separation of hydrophilic/hydrophobic regions by the transmission electron microscopy (TEM) studies. Thermal investigations using TGA and DSC confirm that the membranes are stable up to 250 °C. Particularly, drastically alkaline stability due to no decrease in the hydroxide conductivity after 168 h of treatment with 2M KOH.

  2. Metal nanoparticles/ionic liquid/cellulose: polymeric membrane for hydrogenation reactions

    Directory of Open Access Journals (Sweden)

    Marcos Alexandre Gelesky

    2014-01-01

    Full Text Available Rhodium and platinum nanoparticles were supported in polymeric membranes with 10, 20 and 40 µm thickness. The polymeric membranes were prepared combining cellulose acetate and the ionic liquid (IL 1-n-butyl-3-methylimidazolium bis(trifluoromethane sulfonylimide (BMI.(NTf2. The presence of metal nanoparticles induced an increase in the polymeric membrane surface areas. The increase of the IL content resulted in an improvement of elasticity and decrease in tenacity and toughness, whereas the stress at break was not affected. The presence of IL probably causes an increase in the separation between the cellulose molecules that result in a higher flexibility and processability of the polymeric membrane. The CA/IL/M(0 combinations exhibit an excellent synergistic effect that enhances the activity and durability of the catalyst for the hydrogenation of cyclohexene. The CA/IL/M(0 polymeric membrane displays higher catalytic activity (up to 7.353 h-1 for the 20 mm of CA/IL/Pt(0 and stability than the nanoparticles dispersed only in the IL.

  3. Thermal Stability Limits of Imidazolium Ionic Liquids Immobilized on Metal-Oxides.

    Science.gov (United States)

    Babucci, Melike; Akçay, Aslı; Balci, Volkan; Uzun, Alper

    2015-08-25

    Thermal stability limits of 33 imidazolium ionic liquids (ILs) immobilized on three of the most commonly used high surface area metal-oxides, SiO2, γ-Al2O3, and MgO, were investigated. ILs were chosen from a family of 13 cations and 18 anions. Results show that the acidity of C2H of an imidazolium ring is one of the key factors controlling the thermal stability. An increase in C2H bonding strength of ILs leads to an increase in their stability limits accompanied by a decrease in interionic energy. Systematic changes in IL structure, such as changes in electronic structure and size of anion/cation, methylation on C2 site, and substitution of alkyl groups on the imidazolium ring with functional groups have significant effects on thermal stability limits. Furthermore, thermal stability limits of ILs are influenced strongly by acidic character of the metal-oxide surface. Generally, as the point of zero charge (PZC) of the metal-oxide increases from SiO2 to MgO, the interactions of IL and metal-oxide dominate over interionic interactions, and metal-oxide becomes the significant factor controlling the stability limits. However, thermal stability limits of some ILs show the opposite trend, as the chemical activities of the cation functional group or the electron donating properties of the anion alter IL/metal-oxide interactions. Results presented here can help in choosing the most suitable ILs for materials involving ILs supported on metal-oxides, such as for supported ionic liquid membranes (SILM) in separation applications or for solid catalyst with ionic liquid layer (SCILL) and supported ionic liquid phase (SILP) catalysts in catalysis.

  4. Liquid crystal phase behavior of sterically-stabilized goethite

    NARCIS (Netherlands)

    van den Pol, Esther; Petukhov, Andrei V.; Thies-Weesie, Dominique M.E.; Byelov, Dmytro V.; Vroege, Gert J.

    2010-01-01

    The liquid crystalline phase behavior of sterically-stabilized goethite particles in toluene was studied using small-angle X-ray scattering. The results were compared with those from charged particles in water, with and without magnetic field: similarly rich phase behavior was found. Furthermore,

  5. Thermal stability of nafion membranes under mechanical stress

    Energy Technology Data Exchange (ETDEWEB)

    Quintilii, M.; Struis, R. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1997-06-01

    The feasibility of adequately modified fluoro-ionomer membranes (NAFION{sup R}) is demonstrated for the selective separation of methanol synthesis products from the raw reactor gas at temperatures around 200{sup o}C. For an economically relevant application of this concept on a technical scale the Nafion membranes should be thin ({approx_equal}10 {mu}m) and thermally stable over a long period of time (1-2 years). In cooperation with industry (Methanol Casale SA, Lugano (CH)), we test the thermal stability of Nafion hollow fibers and supported Nafion thin sheet membranes at temperatures between 160 and 200{sup o}C under mechanical stress by applying a gas pressure difference over the membrane surface ({Delta}P{<=} 40 bar). Tests with the hollow fibers revealed that Nafion has visco-elastic properties. Tests with 50 {mu}m thin Nafion sheets supported by a porous metal carrier at 200{sup o}C and {Delta}P=39 bar showed no mechanical defects over a period of 92 days. (author) 5 figs., 4 refs.

  6. Membrane Formation in Liquids by Adding an Antagonistic Salt

    Directory of Open Access Journals (Sweden)

    Koichiro Sadakane

    2018-03-01

    Full Text Available Antagonistic salts are composed of hydrophilic and hydrophobic ions. In a binary mixture, such as water and organic solvent, these ion pairs preferentially dissolve to those phases, respectively, and there is a coupling between the charge density and the composition. The heterogeneous distribution of ions forms a large electric double layer at the interface between these solvents. This reduces the interfacial tension between water and organic solvent, and stabilizes an ordered structure, such as a membrane. These phenomena have been extensively studied from both theoretical and experimental point of view. In addition, the numerical simulations can reproduce such ordered structures.

  7. Membrane formation in liquids by adding an antagonistic salt

    Science.gov (United States)

    Sadakane, Koichiro; Seto, Hideki

    2018-03-01

    Antagonistic salts are composed of hydrophilic and hydrophobic ions. In a binary mixture, such as water and organic solvent, these ion pairs preferentially dissolve to those phases, respectively, and there is a coupling between the charge density and the composition. The heterogeneous distribution of ions forms a large electric double layer at the interface between these solvents. This reduces the interfacial tension between water and organic solvent, and stabilizes an ordered structure, such as a membrane. These phenomena have been extensively studied from both theoretical and experimental point of view. In addition, the numerical simulations can reproduce such ordered structures.

  8. 4-nitrophenol removal from aqueous solutions by emulsion liquid membranes using type I facilitation.

    Science.gov (United States)

    León, G; Guzmán, M A; Miguel, B

    2013-01-01

    Nitrophenols are common organic pollutants that enter the environment during the manufacture and processing of a variety of industrial products. The removal of 4-nitrophenol (4NP) from aqueous solutions by emulsion liquid membranes using the type I facilitated transport mechanism is investigated in this paper. The liquid membrane consisted of kerosene as the organic diluent, sorbitan monooleate as the emulsifying agent and sodium hydroxide as the stripping agent. The most important operational variables governing the emulsion stability and the 4NP removal process--such as the stripper agent and surfactant concentrations, the volume ratios of membrane phase/internal phase and emulsion phase/feed phase and stirring speed - were studied and the optimal conditions of the removal process were experimentally determined. Apparent initial permeabilities of the transport process in the different operational conditions were also obtained. Ninety-eight per cent of4NP was removed in 10 minutes and an apparent initial permeability of 1.2986 min(-1) was obtained in those optimal conditions.

  9. Stability of liquid fuels with biogenic content

    Energy Technology Data Exchange (ETDEWEB)

    Koch, Winfried; Hoffmann, Hajo; Pohland vom Schloss, Heide [OWI - Oel-Waerme-Institut GmbH, Herzogenrath (Germany)

    2013-06-01

    , biodiesel tends to polymerize and thus forms deposits at an exponentially higher level. This increased deposit formation near the fuel supply, which does not occur during operation with mineral fuels, leads to failure of the heater. Operation of the heaters with high blend levels of ethanol led to lean combustion due to the amount of oxygen available in ethanol. As a result, the combustion takes place closer to the lean flame limit. In the framework of other projects, long-term-storage stability tests of different domestic heating oil/FAME-blends in a climate chamber at 40 C and defined air moisture were carried out. (orig.)

  10. Solid-Supported Lipid Membranes: Formation, Stability and Applications

    Science.gov (United States)

    Goh, Haw Zan

    This thesis presents a comprehensive investigation of the formation of supported lipid membranes with vesicle hemifusion, their stability under detergents and organic solvents and their applications in molecular biology. In Chapter 3, we describe how isolated patches of DOPC bilayers supported on glass surfaces are dissolved by various detergents (decyl maltoside, dodecyl maltoside, CHAPS, CTAB, SDS, TritonX-100 and Tween20) at their CMC, as investigated by fluorescence video microscopy. In general, detergents partition into distal leaflets of bilayers and lead to the expansion of the bilayers through a rolling motion of the distal over the proximal leaflets, in agreement with the first stage of the established 3-stage model of lipid vesicle solubilization by detergents. Subsequently, we study the partitioning of organic solvents (methanol, ethanol, isopropanol, propanol, acetone and chloroform) into isolated bilayer patches on glass in Chapter 4 with fluorescence microscopy. The area expansion of bilayers due to the partitioning of organic solvents is measured. From the titration of organic solvents, we measured the rate of area expansion as a function of the volume fraction of organic solvents, which is proposed to be a measure of strength of interactions between solvents and membranes. From the same experiments, we also measure the maximum expansion of bilayers (or the maximum binding stoichiometry between organic solvents and lipids) before structural breakdown, which depends on the depth of penetration of solvents to the membranes. In Chapter 5, we investigate the formation of sparsely-tethered bilayer lipid membranes (stBLMs) with vesicle hemifusion. In vesicle hemifusion, lipid vesicles in contact with a hydrophobic alkyl-terminated self-assembled monolayer (SAM) deposit a lipid monolayer to the SAM surface, thus completing the bilayer. Electrical Impedance Spectroscopy and Neutron Reflectivity are used to probe the integrity of stBLMs in terms of their

  11. Hollow fibre membrane contactor as a gas-liquid model contactor

    NARCIS (Netherlands)

    Dindore, V.Y.; Brilman, Derk Willem Frederik; Versteeg, Geert

    2005-01-01

    Microporous hollow fiber gas–liquid membrane contactors have a fixed and well-defined gas–liquid interfacial area. The liquid flow through the hollow fiber is laminar, thus the liquid side hydrodynamics are well known. This allows the accurate calculation of the fiber side physical mass transfer

  12. Hollow fiber membrane contactor as a gas-liquid model contactor

    NARCIS (Netherlands)

    Dindore, V. Y.; Brilman, D. W. F.; Versteeg, G. F.

    2005-01-01

    Microporous hollow fiber gas-liquid membrane contactors have a fixed and well-defined gas-liquid interfacial area. The liquid flow through the hollow fiber is laminar, thus the liquid side hydrodynamics are well known. This allows the accurate calculation of the fiber side physical mass transfer

  13. Liquid Tubule Formation and Stabilization Using Cellulose Nanocrystal Surfactants.

    Science.gov (United States)

    Liu, Xubo; Shi, Shaowei; Li, Yanan; Forth, Joe; Wang, Dong; Russell, Thomas P

    2017-10-02

    Structured liquids, generated by the interfacial formation, assembly, and jamming of nanoparticle (NP)-surfactants at liquid/liquid interfaces, maintain all the desirable characteristics of each liquid, while providing a spatially structured framework. Herein, we show that rod-like cellulose nanocrystal (CNC)-based NP-surfactants, termed CNC-surfactants, are formed rapidly at the liquid/liquid interface, assemble into a monolayer, and, when jammed, offer a robust assembly with exceptional mechanical properties. Plateau-Rayleigh (PR) instabilities of a free-falling jet of an aqueous medium containing the CNCs into a toluene solution of amine end-functionalized polystyrene are completely suppressed, allowing the jetting of aqueous tubules that are stabilized when the CNC-surfactants are jammed at the interface. These results open a new platform for the additive manufacturing techniques, for example, three-dimensional (3D) printing, of all-liquid constructs. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Shear Strength of Stabilized Kaolin Soil Using Liquid Polymer

    Science.gov (United States)

    Azhar, A. T. S.; Fazlina, M. I. S.; Nizam, Z. M.; Fairus, Y. M.; Hakimi, M. N. A.; Riduan, Y.; Faizal, P.

    2017-08-01

    The purpose of this research is to investigate the suitability of polymer in soil stabilization by examining its strength to withstand compressive strength. Throughout this research study, manufactured polymer was used as a chemical liquid soil stabilizer. The liquid polymer was diluted using a proposed dilution factor of 1 : 3 (1 part polymer: 3 parts distilled water) to preserve the workability of the polymer in kaolin mixture. A mold with a diameter of 50 mm and a height of 100 mm was prepared. Kaolin soil was mixed with different percentages of polymer from 10%, 15%, 20%, 25%, 30% and 35% of the mass of the kaolin clay sample. Kaolin mixtures were tested after a curing period of 3 days, 7 days, 14 days and 28 days respectively. The physical properties were determined by conducting a moisture content test and Atterberg limit test which comprise of liquid limit, plastic limit and shrinkage limit. Meanwhile, the mechanical properties of the soil shear strength were identified through an unconfined compressive strength (UCS) test. Stabilized kaolin soil showed the highest compressive strength value when it was mixed with 35% of polymer compared to other percentages that marked an increment in strength which are 45.72% (3 days), 67.57% (7 days), 81.73% (14 days) and 77.84% (28 days). Hence, the most effective percentage of liquid polymer which should be used to increase the strength of kaolin soil is 35%.

  15. Stability of triglyceride liquid films on hydrophilic and hydrophobic glasses.

    Science.gov (United States)

    Vazquez, Rosa; Nogueira, Rui; Orfão, Marta; Mata, José Luís; Saramago, Benilde

    2006-07-01

    Wetting and dewetting of solid surfaces by oily fluids were investigated in terms of the stability of the liquid film formed between an air bubble and the solid surface. With the objective of understanding how molecules with low polarity but relatively complex molecular structure behave at the solid/liquid interface, three liquid triglycerides with different chain length and saturation were chosen, namely, tributyrin, tricaprylin, and triolein. Tributyrin and tricaprylin exist in milkfat while triolein is present in vegetable oils. The stability of the liquid films may be inferred from the shape of the disjoining pressure isotherms, which represent the dependence of the disjoining pressure on the film thickness. Disjoining pressure isotherms for films of the three triglycerides on hydrophilic and hydrophobic glasses were obtained using a recently developed apparatus, based on the interferometric technique. The experimental curves are compared with the theoretical predictions of London-Hamaker. The deviations between theory and experiment are interpreted in terms of a structural component of the disjoining pressure. All triglycerides form metastable films on both hydrophilic and hydrophobic glasses which means that for disjoining pressures higher than a critical value, pi(c), a wetting transition occurs and the film ruptures. The mechanisms for film rupture are discussed and a correlation between film stability and the apolar (Lifshitz-van der Waals) and the polar components of the spreading coefficient is proposed.

  16. Erythrocyte membrane stabilization effect and antioxidant activity of methyl methacrylate

    International Nuclear Information System (INIS)

    Popov, B.

    2004-01-01

    Methyl methacrylate (MMK) is a synthetic product with mild impact on human health that is not well studied on cellular basis. Here, human erythrocytes were used to investigate the effects MMK exerts on acid and heat-induced hemolysis. Biphasic effect of MMK was observed for acid-induced hemolysis; i.e., protection at low (0 - 0.05% v/v) and stimulation at higher (0.1- 0.4% v/v) concentrations. The maximal protective effect was produced at 0.03% (v/v). At this concentration MMK increased the temperatures of heat denaturation of erythrocyte membrane proteins, spectrin and integral proteins, by about 2 0 C and inhibited the heat-induced hemolysis by 20 %. This membrane stabilization effect of MMK is similar to that produced by some anti-inflammatory and antirheumatic drugs. The increased acid resistance possibly indicated anti-oxidant properties of MMK. The nonenzymatic antioxidant activity test evidenced that MMK has no superoxide dismutase-like activity but demonstrates strong catalase-like activity (about 900 kU/mmol at 0.05-0.1 mmol/l concentration). The results indicate that at low concentration MMK exerts benign effect on cellular membrane that could find therapeutic usage. (author)

  17. A Review of Polymer-Stabilized Ferroelectric Liquid Crystals

    Directory of Open Access Journals (Sweden)

    Ingo Dierking

    2014-05-01

    Full Text Available The polymer stabilized state of ferroelectric liquid crystals (FLC is reviewed; and the effect of a dispersed polymer network in an FLC outlined and discussed. All fundamental material aspects are demonstrated; such as director tilt angle; spontaneous polarization; response time and viscosity; as well as the dielectric modes. It was found that the data can largely be explained by assuming an elastic interaction between the polymer network strands and the liquid crystal molecules. The elastic interaction parameter was determined; and increases linearly with increasing polymer concentration.

  18. A Review of Polymer-Stabilized Ferroelectric Liquid Crystals

    Science.gov (United States)

    Dierking, Ingo

    2014-01-01

    The polymer stabilized state of ferroelectric liquid crystals (FLC) is reviewed; and the effect of a dispersed polymer network in an FLC outlined and discussed. All fundamental material aspects are demonstrated; such as director tilt angle; spontaneous polarization; response time and viscosity; as well as the dielectric modes. It was found that the data can largely be explained by assuming an elastic interaction between the polymer network strands and the liquid crystal molecules. The elastic interaction parameter was determined; and increases linearly with increasing polymer concentration. PMID:28788637

  19. A Review of Polymer-Stabilized Ferroelectric Liquid Crystals.

    Science.gov (United States)

    Dierking, Ingo

    2014-05-06

    The polymer stabilized state of ferroelectric liquid crystals (FLC) is reviewed; and the effect of a dispersed polymer network in an FLC outlined and discussed. All fundamental material aspects are demonstrated; such as director tilt angle; spontaneous polarization; response time and viscosity; as well as the dielectric modes. It was found that the data can largely be explained by assuming an elastic interaction between the polymer network strands and the liquid crystal molecules. The elastic interaction parameter was determined; and increases linearly with increasing polymer concentration.

  20. Phase stability analysis of liquid-liquid equilibrium with stochastic methods

    Directory of Open Access Journals (Sweden)

    G. Nagatani

    2008-09-01

    Full Text Available Minimization of Gibbs free energy using activity coefficient models and nonlinear equation solution techniques is commonly applied to phase stability problems. However, when conventional techniques, such as the Newton-Raphson method, are employed, serious convergence problems may arise. Due to the existence of multiple solutions, several problems can be found in modeling liquid-liquid equilibrium of multicomponent systems, which are highly dependent on the initial guess. In this work phase stability analysis of liquid-liquid equilibrium is investigated using the NRTL model. For this purpose, two distinct stochastic numerical algorithms are employed to minimize the tangent plane distance of Gibbs free energy: a subdivision algorithm that can find all roots of nonlinear equations for liquid-liquid stability analysis and the Simulated Annealing method. Results obtained in this work for the two stochastic algorithms are compared with those of the Interval Newton method from the literature. Several different binary and multicomponent systems from the literature were successfully investigated.

  1. Development of membrane cryostats for large liquid argon neutrino detectors

    CERN Document Server

    Montanari, D; Gendotti, A; Geynisman, M; Hentschel, S; Loew, T; Mladenov, D; Montanari, C; Murphy, S; Nessi, M; Norris, B; Noto, F; Rubbia, A; Sharma, R; Smargianaki, D; Stewart, J; Vignoli, C; Wilson, P; Wu, S

    2015-01-01

    A new collaboration is being formed to develop a multi-kiloton Long-Baseline neutrino experiment that will be located at the Surf Underground Research Facility (SURF) in Lead, SD. In the present design, the detector will be located inside cryostats filled with 68,400 ton of ultrapure liquid argon (less than 100 parts per trillion of oxygen equivalent contamination). To qualify the membrane technology for future very large-scale and underground implementations, a strong prototyping effort is ongoing: several smaller detectors of growing size with associated cryostats and cryogenic systems will be designed and built at Fermilab and CERN. They will take physics data and test different detector elements, filtration systems, design options and installation procedures. In addition, a 35 ton prototype is already operational at Fermilab and will take data with single-phase detector in early 2016. After the prototyping phase, the multi-kton detector will be constructed. After commissioning, it will detect and study ne...

  2. Nanoporous membranes with electrochemically switchable, chemically stabilized ionic selectivity

    Science.gov (United States)

    Small, Leo J.; Wheeler, David R.; Spoerke, Erik D.

    2015-10-01

    Nanopore size, shape, and surface charge all play important roles in regulating ionic transport through nanoporous membranes. The ability to control these parameters in situ provides a means to create ion transport systems tunable in real time. Here, we present a new strategy to address this challenge, utilizing three unique electrochemically switchable chemistries to manipulate the terminal functional group and control the resulting surface charge throughout ensembles of gold plated nanopores in ion-tracked polycarbonate membranes 3 cm2 in area. We demonstrate the diazonium mediated surface functionalization with (1) nitrophenyl chemistry, (2) quinone chemistry, and (3) previously unreported trimethyl lock chemistry. Unlike other works, these chemistries are chemically stabilized, eliminating the need for a continuously applied gate voltage to maintain a given state and retain ionic selectivity. The effect of surface functionalization and nanopore geometry on selective ion transport through these functionalized membranes is characterized in aqueous solutions of sodium chloride at pH = 5.7. The nitrophenyl surface allows for ionic selectivity to be irreversibly switched in situ from cation-selective to anion-selective upon reduction to an aminophenyl surface. The quinone-terminated surface enables reversible changes between no ionic selectivity and a slight cationic selectivity. Alternatively, the trimethyl lock allows ionic selectivity to be reversibly switched by up to a factor of 8, approaching ideal selectivity, as a carboxylic acid group is electrochemically revealed or hidden. By varying the pore shape from cylindrical to conical, it is demonstrated that a controllable directionality can be imparted to the ionic selectivity. Combining control of nanopore geometry with stable, switchable chemistries facilitates superior control of molecular transport across the membrane, enabling tunable ion transport systems.Nanopore size, shape, and surface charge all play

  3. Targeting proteins to liquid-ordered domains in lipid membranes.

    Science.gov (United States)

    Stachowiak, Jeanne C; Hayden, Carl C; Sanchez, Mari Angelica A; Wang, Julia; Bunker, Bruce C; Voigt, James A; Sasaki, Darryl Y

    2011-02-15

    We demonstrate the construction of novel protein-lipid assemblies through the design of a lipid-like molecule, DPIDA, endowed with tail-driven affinity for specific lipid membrane phases and head-driven affinity for specific proteins. In studies performed on giant unilamellar vesicles (GUVs) with varying mole fractions of dipalymitoylphosphatidylcholine (DPPC), cholesterol, and diphytanoylphosphatidyl choline (DPhPC), DPIDA selectively partitioned into the more ordered phases, either solid or liquid-ordered (L(o)) depending on membrane composition. Fluorescence imaging established the phase behavior of the resulting quaternary lipid system. Fluorescence correlation spectroscopy confirmed the fluidity of the L(o) phase containing DPIDA. In the presence of CuCl(2), the iminodiacetic acid (IDA) headgroup of DPIDA forms the Cu(II)-IDA complex that exhibits a high affinity for histidine residues. His-tagged proteins were bound specifically to domains enriched in DPIDA, demonstrating the capacity to target protein binding selectively to both solid and L(o) phases. Steric pressure from the crowding of surface-bound proteins transformed the domains into tubules with persistence lengths that depended on the phase state of the lipid domains.

  4. Membrane–solvent selection for CO2 removal using membrane gas–liquid contactors

    NARCIS (Netherlands)

    Dindore, V.Y.; Brilman, D.W.F.; Geuzebroek, F.H.; Versteeg, G.F.

    2004-01-01

    Membrane gas–liquid contactors can provide very high interfacial area per unit volume, independent regulation of gas and liquid flows and are insensitive to module orientation, which make them very attractive in comparison with conventional equipments for offshore application. However, the membrane

  5. Stability of thin liquid films containing surface active particles

    Science.gov (United States)

    Umashankar, Hariharan; Kalpathy, Sreeram; Dixit, Harish

    2017-11-01

    The stability and dynamics of thin liquid films(industrial settings like coating and printing processes and extraction of oil from porous rocks. In this study a hydrodynamic model is introduced to capture the long term evolution of a Newtonian liquid film containing insoluble surfaceactive particles.We consider here the possibility of four distinct interaction regimes based on the surface rheological effects of the particles, such that either, both or neither of Marangoni and surface viscosity effects would be present at the leading order in the governing equations. The liquid film is bounded by a rigid impermeable solid below and covered by passive air phase above.A standard linear stability analysis and nonlinear simulations are performed on the set of highly coupled partial differential evolution equations. Linear stability analysis gives insights on whether a particular imposed perturbationwavenumber will grow or decay in time and also evaluating the fastest growing wavenumber. Parametric studies for all four regimes provides a strong confirmation that surface viscosity and Marangoni effects are indeed rupture delaying effects.

  6. Liquid anion exchangers (LAE) as novel receptors for plutonium pertraction across polymer immobilized liquid membranes

    International Nuclear Information System (INIS)

    Sonawane, J.V.; Anil Kumar; Sawant, S.R.; Singh, R.K.; Bajpai, D.D.; Shukla, J.P.

    1999-03-01

    The diffusion-limited and amine-facilitated Pu 4+ cation permeation in nitric acid media across a polymer immobilized liquid membrane (PILM) has been investigated to quantify the membrane carrier type effects on its transport. Primene JM-T (JMT) as primary, Amberlite LA-2 (Amb LA-2) as secondary, trilaurylamine (TLA] and triiso-octyl amine (TIOA) as tertiary and Adogen-464 (Ado-464) and Aliquat-336 (Ali-336) as quaternary amines as typical examples of nitrogen containing basic extractants are tested as the carriers. After suitable dilutions, the receptors are immobilized on a microporous polymeric support which are held within the pores by capillary forces. Both the composition of the organic membrane solvents and type of amine carriers exert a marked effect on plutonium permeation. Recovery of Pu steadily increases from primary to quaternary amines; its permeability across PILM roughly follows the order quaternary > tertiary > secondary > primary, similar to that generally observed in liquid-liquid distribution experiments. More than 95% pertraction of Pu(IV) is easily accomplished using tertiary or quaternary amine as ionophores across PILM in single run employing a feed solution containing about 5 mg dm -3 Pu in 4 M nitric acid solution while the receiving phase is 0.1M NH 2 OH.HCl prepared in 0.3M HNO 3 . On the other hand, plutonium permeation at 4M HNO 3 under similar experimental conditions using other types of amines as carriers namely primary amine, Pri JM-T afforded only 19% and 49% by Amb LA-2 in 6-7h runs. Results of the detailed study to evaluate the effect of other contaminants on Pu transport are also discussed. (author)

  7. Dicyclohexano-18-crown-6 as a novel carrier in the liquid membrane permeation of actinides

    International Nuclear Information System (INIS)

    Kumar, Anil; Singh, R.K.; Bajpai, D.D.; Shukla, J.P.

    1994-01-01

    The proven extractability and profound selectivity of dicyclohexano-18-crown-6 (DC18C6) has been exploited by selecting this crown ether as the ionophore in liquid membrane transport. Macrocycle-facilitated transport of Pu(IV) and U(VI) against their concentration gradient from aqueous nitric acid solutions across organic bulk liquid membrane (BLM) and thin-sheet supported liquid membrane (SLM) containing DC18C6 as the mobile carrier and toluene as the membrane solvent was investigated. (author). 23 refs., 9 tabs., 7 figs

  8. Recovery of salicylic acid from aqueous solution by solvent extraction and supported liquid membrane using TOMAC as carrier

    International Nuclear Information System (INIS)

    Kouki, Noura; Tayeb, Rafik; Dhahbi, Mahmoud

    2009-01-01

    Conventional sewage treatment plants do not fully degrade residues of pharmaceuticals, so that they are introduced into the aquatic environment. On this basis, the demand for the development of efficient systems for removing these compounds from water has assumed a great research interest. Membrane operations are increasingly employed in many industrial sectors as important alternative technologies to the classical processes of separation. Among membrane-based separation processes, the use of supported liquid membranes (SLMs) has received growing attention during recent years. In our work we had tried to recover a pharmaceutical product, salicylic acid (S.A), from an aqueous solution by solvent extraction and supported liquid membrane using an ionic liquid: the tri octylmethylammonium chloride (TOMAC) as carrier. Ionic liquids has been revealed as interesting clean alternatives to classical solvents and their use as a liquid phase results in the stabilization of the SLMs duo to their negligible vapour pressure, the possibility of minimising their solubility in the surrounding phases by adequate selection of the cation and anion, and the greater capillary force associated with their high viscosity. For this reason we had studied the influence of different parameters which could affect the efficiency of the transport: pH of the feed phase, the nature of the strippant, the concentration of the strippant, the nature of the support and the initial concentration of the salicylic acid in the feed phase. We had noticed that the pH of the feed solution had no effect of the percentage extraction and after 24 hours we can extract completely our solute. TOMAC seemed to be a good extractant but we found difficult to strip salicylic acid from the TOMAC phase and this could be related to the formation of water micro environments in the ionic liquid membrane.

  9. Uranium extraction process in a sulfuric medium by means of liquid emulsified membranes

    International Nuclear Information System (INIS)

    Monteillet, A.

    1985-02-01

    Uranium ore processing, after leaching by sulfuric acid, by liquid-liquid extraction is a rather heavy process, not suitable for small deposits. Extraction by emulsions was suggested. In this process the leachate is contacted with an oil in water type emulsion, a liquid organic membrane is formed by the continuous phase. Uranium complexes diffuse through the liquid membrane towards the dispersed aqueous phase of the emulsion (stripping solution). Uranium is recovered by breaking the emulsion. Are successively studied: development of stable emulsions, influence of emulsion composition on uranium transfer kinetics, transfer mechanisms through the membrane and modelling of kinetics data obtained in the experimental study [fr

  10. Advanced Supported Liquid Membranes for Carbon Dioxide Control in Extravehicular Activity Applications

    Science.gov (United States)

    Wickham, David T. (Inventor); Gleason, Kevin J. (Inventor); Cowley, Scott W. (Inventor)

    2015-01-01

    There is disclosed a portable life support system with a component for removal of at least one selected gas. In an embodiment, the system includes a supported liquid membrane having a first side and a second side in opposition to one another, the first side configured for disposition toward an astronaut and the second side configured for disposition toward a vacuum atmosphere. The system further includes an ionic liquid disposed between the first side and the second side of the supported liquid membrane, the ionic liquid configured for removal of at least one selected gas from a region housing the astronaut adjacent the first side of the supported liquid membrane to the vacuum atmosphere adjacent the second side of the supported liquid membrane. Other embodiments are also disclosed.

  11. The liquid membrane for extraction of Yttrium and Dysprosium from Acid Nitric

    International Nuclear Information System (INIS)

    Johny, W.S.; Raldi-Artono-Koestoer; Kris-Tri-Basuki; Sudibyo

    1996-01-01

    The determination of surfactant in liquid membrane has been done. The surfactant is span-80 (sorbitol-monooleate), the liquid membrane phase was the organic phase (O), the internal liquid phase (W) with ratio O/W = 1, and surfactant. The organic phase using D 2 EHPA in the kerosene and the internal liquid phase using aqua des or acid nitric. The determination of surfactant with variation of span-80 (0,25 - 2%) in the liquid membrane volume. The speed of stirrer was 3500 rpm in 20 minute. The ratio of liquid membrane phase form and external phase (aqua des or acid nitric) was 1, the speed of stirrer was 350 rpm in 10 minute (permeation process). The liquid phase and the liquid membrane phase was separated and then determinated the volume of liquid membrane, the result of percentage of span-80 was 0,25 % volume. The extraction of yttrium and dysprosium in 2 M HNO 3 was Kd y = 2.945 and Kd D y = 0.019

  12. Extraction of nickel by liquid membranes in an electric field

    Energy Technology Data Exchange (ETDEWEB)

    Serga, V.E.; Kulikova, L.D.; Purin, B.A.

    2000-01-01

    The known liquid membranes (impregnated and emulsion) based on di-2-ethylhexylphosphoric acid (D2EHPA) extract nickel only out of weakly acid and neutral solutions. The authors have found that direct current applied to an extraction system contributes to the complete extraction of nickel cations (0.003--0.009 M NiSO{sub 4}) out of more acidic solutions (C{sub H{sub 2}SO{sub 4}} {le} 0.05 M) as well. The organic membrane phase is a D2EHPA solution (20 vol%) in 1,2-dichloroethane with 5--20 vol% of tributyl phosphate (I) or 1--2 vol% n-trioctylamine (II) added. These additions increase the electrical conductivity of the system 10--20 times. This allows for the extraction of nickel cations at optimal values of current density (for I: i {le} 2.1 mA/cm{sup 2}; for II: i {ge} 4.9 mA/cm{sup 2}). It is shown that the flow of nickel cations through the feed solution/organic phase interface increases with a certain increase of current density, metal content in the aqueous phase, and amount of addition of I or II in the studied concentration range. Chronopotentiograms can be used to estimate the efficiency of nickel extraction. If an electric field is applied, the transfer of nickel cations is codirected with that of hydrogen ions through the interface. Kinetic measurements of nickel cation as well as of hydrogen ion transport numbers revealed that the nickel cation extraction process was preceded by the transport of hydrogen ions through the feed solution/organic phase interface.

  13. Passive and Active Stabilization of Liquid Bridges in Low Gravity

    Science.gov (United States)

    Marston, Philip L.; Thiessen, David B.; Marr-Lyon, Mark J.; Wei, Wei; Niederhaus, Charles E.; Truong, Duc K.

    2001-01-01

    Tests are planned in the low gravity environment of the International Space Station (ISS) of new methods for the suppression of the capillary instability of liquid bridges. Our suppression methods are unusual in that they are not limited to liquid bridges having very special properties and may impact a variety of low-gravity and earth-based technologies. There are two main approaches to be investigated: (1) Passive Acoustic Stabilization (PAS); and (2) Active Electrostatic Stabilization (AES). In PAS, the suppression of the mode growth is accomplished by placing the bridge in an acoustic field having the appropriate properties such that the acoustic radiation pressure automatically pulls outward on the thinnest portion of the bridge. In AES, the bridge deformation is sensed optically and counteracted by actively adjusting the electrostatic Maxwell stresses via two ring electrodes concentric with the slightly conducting bridge to offset the growth of the unstable mode. While the present work emphasizes cylindrical bridges, the methods need not be restricted to that case. The methods to be explored are relevant to the suppression of capillary instabilities in floating zone crystal growth, breakup of liquid jets and columns, bubbles, and annular films as well as the management of coolants or propellants in low-gravity.

  14. Stability of amorphous silica-alumina in hot liquid water.

    Science.gov (United States)

    Hahn, Maximilian W; Copeland, John R; van Pelt, Adam H; Sievers, Carsten

    2013-12-01

    Herein, the hydrothermal stability of amorphous silica-alumina (ASA) is investigated under conditions relevant for the catalytic conversion of biomass, namely in liquid water at 200 °C. The hydrothermal stability of ASA is much higher than that of pure silica or alumina. Interestingly, the synthetic procedure used plays a major role in its resultant stability: ASA prepared by cogelation (CG) lost its microporous structure, owing to hydrolysis of the siloxane bonds, but the resulting mesoporous material still had a considerable surface area. ASA prepared by deposition precipitation (DP) contained a silicon-rich core and an aluminum-rich shell. In hot liquid water, the latter structure was transformed into a layer of amorphous boehmite, which protected the particle from further hydrolysis. The surface area showed relatively minor changes during the transformation. Independent of the synthetic method used, the ASAs retained a considerable concentration of acid sites. The concentration of acid sites qualitatively followed the changes in surface area, but the changes were less pronounced. The performance of different ASAs for the hydrolysis of cellobiose into glucose is compared. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Stability of Adderall in extemporaneously compounded oral liquids.

    Science.gov (United States)

    Justice, J; Kupiec, T C; Matthews, P; Cardona, P

    2001-08-01

    The short-term stability of Adderall in three extemporaneously compounded oral liquids was studied. Three suspensions of Adderall 1 mg/mL were prepared from commercially available 10-mg Adderall tablets with Ora-Sweet, Ora-Plus, and a 1:1 mixture of Ora-Sweet and Ora-Plus. Each suspension was stored in the dark in a stability chamber at 25 degrees C and 60% relative humidity for 30 days. The stability of the active drug (a mixture of levoamphetamine and dextroamphetamine salts) in each of the three vehicles was determined immediately after preparation and at 10, 20, and 30 days by using gas chromatography-mass spectrometry (GCMS). No significant changes in concentrations of either amphetamine isomer occurred during the 30-day study period. Visual inspection of samples revealed no changes in color or odor. Extemporaneously compounded liquid oral formulations of Adderall 1 mg/mL in Ora-Sweet, Ora-Plus, or a 1:1 mixture of Ora-Sweet and Ora-Plus were stable for at least 30 days at 25 degrees C and 60% relative humidity.

  16. PENGARUH SIMULASI PENGARUH KONSENTRASI SOLID DAN GEOMETRI BIOREAKTOR MEMBRAN TERENDAM TERHADAP PERPINDAHAN MASSA GAS-LIQUID DAN FLUKS MELALUI MEMBRAN

    Directory of Open Access Journals (Sweden)

    Aisyah Endah Palupi

    2012-09-01

    Full Text Available Abstract: Hydrodynamics characteristic for the mixing of gas-solid-liquid in membrane bioreactor submerged (MBRs and its influence on mass transfer was studied computationally at various solid concentration, incoming gas rate, and the baffle distance. Computational method was conducted by using software GAMBIT 2.1.6. for the making of the grid which represents the calculation domain and conduct the simulation using CFD software FLUENT commercial code 6.2.16. Multiphase flow in reactor was simulated with mixture model, while to model the turbulence characteristic of the flow standard k-ε model was used. The geometrical system investigate is bioreactor in the form of box with flat bottom, 2 baffles, submerged membrane and air passage through the reactor bottom. The membrane type used is hollow fiber, the liquid used is water, and the solid is activated sludge, and air acts as gas phase. The result indicates that closer the baffle to the membrane, the liquid dispersion process goes faster, so that fluid in tank can be mixed perfectly and it can increase the gas-liquid mass transfer rate and the flux at MBRs. The increase of the solid concentration does not significantly affect the change of gas-liquid mass transfer rate and flux through the membrane, but the increase of air flow rate can accelerate the gas-liquid mass transfer and the flux. The position of baffle 9 cm from tank wall is the best position among the others because the amount of air flow is balanced with the circulating fluid flow. Consider from the solid distribution, double inlet MBRs is better compared to that of single inlet. Flux obtained does not show significant difference. From the both approach of the membrane model, membrane model as porous media give the simulation results closer to the experimental data.

  17. Hydrothermal stability of silica, hybrid silica and Zr-doped hybrid silica membranes

    NARCIS (Netherlands)

    ten Hove, Marcel; Luiten-Olieman, Mieke W.J.; Huiskes, Cindy; Nijmeijer, Arian; Winnubst, Louis

    2017-01-01

    Hybrid silica membranes have demonstrated to possess a remarkable hydrothermal stability in pervaporation and gas separation processes allowing them to be used in industrial applications. In several publications the hydrothermal stability of pure silica or that of hybrid silica membranes are

  18. Stability of dolasetron in two oral liquid vehicles.

    Science.gov (United States)

    Johnson, Cary E; Wagner, Deborah S; Bussard, Wendy E

    2003-11-01

    The stability of dolasetron 10 mg/mL over 90 days when prepared as an oral liquid formulation from commercially available tablets in both strawberry syrup and a sugar-free vehicle was studied. A liquid suspension of dolasetron mesylate 10 mg/mL was prepared from commercially available dolasetron tablets, OraPlus, and Ora-Sweet or strawberry syrup. Six samples of each formulation were prepared and stored in amber plastic bottles. Three samples of each formulation were refrigerated (3-5 degrees C) and three were stored at room temperature (23-25 degrees C). A 1-mL sample was withdrawn from each of the 12 bottles immediately and after 7, 14, 30, 60, and 90 days. After further dilution to an expected concentration of 10 micrograms/mL with sample diluent, the solutions were assayed in duplicate using high-performance liquid chromatography. The samples were also inspected for color and odor changes, and the pH of each sample was determined. The stability-indicating capability of the dolasetron assay was determined by forced degradation of four separate 10-mg/mL samples exposed to direct sunlight for 90 days. There were no detectable changes in color, odor, or taste and no visible microbial growth in any sample. At least 98% of the initial dolasetron concentration remained throughout the 90-day study period for all samples. An extemporaneously compounded oral liquid preparation of dolasetron mesylate 10 mg/mL in a 1:1 mixture of Ora-Plus and strawberry syrup or Ora-Sweet was stable for at least 90 days when stored at 3-5 or 23-25 degrees C.

  19. High-efficiency technology for lithium isotope separation using an ionic-liquid impregnated organic membrane

    International Nuclear Information System (INIS)

    Hoshino, Tsuyoshi; Terai, Takayuki

    2011-01-01

    The tritium needed as a fuel for fusion reactors is produced by the neutron capture reaction of lithium-6 ( 6 Li) in tritium breeding materials. New lithium isotope separation technique using ionic-liquid impregnated organic membranes (Ionic-Liquid-i-OMs) have been developed. Lithium ions are able to move by electrodialysis through certain Ionic-Liquid-i-OMs between the cathode and the anode in lithium solutions. In this report, the effects of protection cover and membrane thickness on the durability of membrane and the efficiency of isotope separation were evaluated. In order to improve the durability of the Ionic-Liquid-i-OM, we developed highly-durable Ionic-Liquid-i-OM. Both surfaces of the Ionic-Liquid-i-OM were covered by a nafion 324 overcoat or a cation exchange membrane (SELEMION TM CMD) to prevent the outflow of the ionic liquid. It was observed that the durability of the Ionic-Liquid-i-OM was improved by a nafion 324 overcoat. On the other hand, the organic membrane selected was 1, 2 or 3 mm highly-porous Teflon film, in order to efficiently impregnate the ionic liquid. The 6 Li isotope separation factor by electrodialysis using highly-porous Teflon film of 3 mm thickness was larger than using that of 1 or 2 mm thickness.

  20. Stability of enalapril maleate in three extemporaneously prepared oral liquids.

    Science.gov (United States)

    Nahata, M C; Morosco, R S; Hipple, T F

    1998-06-01

    The stability of enalapril 1 mg/mL (as the maleate) in deionized water, citrate buffer solution, and a sweetened suspending agent at two temperatures was studied. Twenty enalapril 10-mg tablets were crushed to a powder. Deionized water, citrate buffer solution, or sweetened vehicle was added to produce three 200-mL batches of each liquid; the expected final concentration of enalapril in each was 1 mg/mL. Each formulation was stored in 10 60-mL bottles, 5 of which were stored at 4 degrees C and 5 at 25 degrees C. Samples were collected on days 0, 7, 14, 28, 42, 56, 70, and 91 for visual inspection and analysis by high-performance liquid chromatography; pH was measured at each sampling time as well. The mean concentration of enalapril in the three liquids at 4 degrees C was > 94% of the initial concentration throughout the 91-day study period. At 25 degrees C, the mean concentration of enalapril was > 90% for 56 days and > 92% for 91 days in both citrate buffer solution and sweetened vehicle. The pH of the liquid prepared with deionized water and stored at 25 degrees C decreased by 2.0 pH units. Enalapril 1 mg/mL (as the maleate) in three extemporaneously compounded oral liquids was stable for 91 days at 4 and 25 degrees C with the exception of enalapril in deionized water, which was stable for only 56 days at 25 degrees C.

  1. Evaluation of transport properties of nanofiltration membranes exposed to radioactive liquid waste

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Elizabeth E.M.; Barbosa, Celina C.R.; Bastos, Edna T.R., E-mail: eemo@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeira, RJ (Brazil); Afonso, Julio C., E-mail: Julio@iq.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Inst. de Quimica. Dept. de Quimica Analitica

    2011-07-01

    The application of membrane separation processes (PSM) for treatment of radioactive waste requires the selection of a suitable membrane for the treatment of waste, as the membrane will be directly exposed to the radioactive liquid waste, and also exposed to ionizing radiation. The nanofiltration membrane is most suitable for treatment of radioactive waste, since it has high rejection of multivalent ions. Usually the membranes are made of polymers and depending on the composition of the waste, type and dose of radiation absorbed may be changes in the structure of the membrane, resulting in loss of its transport properties. We tested two commercial nanofiltration membranes: NF and SW Dow/Filmtec. The waste liquid used was obtained in the process of conversion of uranium hexafluoride gas to solid uranium dioxide, known as 'carbonated water'. The membranes were characterized as their transport properties (hydraulic permeability, permeate flux and salt rejection) before and after their immersion in the waste for 24 hours. The surface of the membranes was also evaluated by SEM and FTIR. It was observed that in both the porosity of the membrane selective layer was altered, but not the membrane surface charge, which is responsible for the selectivity of the membrane. The NF membranes and SW showed uranium ion rejection of 64% and 55% respectively. (author)

  2. Stability of tetraphenyl butadiene thin films in liquid xenon

    International Nuclear Information System (INIS)

    Sanguino, P.; Balau, F.; Botelho do Rego, A.M.; Pereira, A.; Chepel, V.

    2016-01-01

    Tetraphenyl butadiene (TPB) is widely used in particle detectors as a wavelength shifter. In this work we studied the stability of TPB thin films when immersed in liquid xenon (LXe). The thin films were deposited on glass and quartz substrates by thermal evaporation. Morphological and chemical surface properties were monitored before and after immersion into LXe by scanning electron microscopy and X-ray photoelectron spectroscopy. No appreciable changes have been detected with these two methods. Grain size and surface chemical composition were found to be identical before and after submersion into LXe. However, the film thickness, measured via optical transmission in the ultraviolet–visible wavelength regions, decreased by 1.6 μg/cm 2 (24%) after immersion in LXe during 20 h. These results suggest the necessity of using a protective thin film over the Tetraphenyl butadiene when used as a wavelength shifter in LXe particle detectors. - Highlights: • Stability of tetraphenyl butadiene (TPB) thin films immersed in liquid xenon (LXe). • Thermally evaporated TPB thin films were immersed in LXe for 20 h. • Film morphology and chemical surface properties remained unchanged. • Surface density of the films decreased by 1.6 μg/cm 2 (24%) after immersion in LXe. • For using in LXe particle detectors, TPB films should be protected with a coating.

  3. Physically Gelled Room-Temperature Ionic Liquid-Based Composite Membranes for CO2/N-2 Separation: Effect of Composition and Thickness on Membrane Properties and Performance

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen, PT; Voss, BA; Wiesenauer, EF; Gin, DL; Nobe, RD

    2013-07-03

    An aspartame-based, low molecular-weight organic gelator (LMOG) was used to form melt-infused and composite membranes with two different imidazolium-based room-temperature ionic liquids (RTILs) for CO2 separation from N-2. Previous work demonstrated that LMOGs can gel RTILs at low, loading levels, and this aspartame-based LMOG was selected because it has been reported to gel a large number of RTILs. The imidazolium-based RTILs were used because of their inherent good properties for CO2/light gas separations. Analysis of the resulting bulk RTIL/LMOG physical gels showed that these materials have high sol-gel transition temperatures (ca. 135 degrees C) suitable for flue gas applications. Gas permeabilities and burst pressure measurements of thick, melt infused membranes revealed a trade-off between high CO2 permeabilities and good mechanical stability as a function of the LMOG loading. Defect-free, composite membranes of the gelled RTILs were successfully fabricated by choosing an appropriate porous membrane support (hydrophobic PTFE) using a suitable coating technique (roller coating). The thicknesses of the applied composite gel layers ranged from 10.3 to 20.7 mu m, which represents an order of magnitude decrease in active layer thickness, compared to the original melt-infused gel RTIL membranes.

  4. The Influence of Extractant TOA, Stirring Time on the Extraction ProcessLiquid-liquid, and Liquid Membrane on the Liquid Wastes Containing Cd

    International Nuclear Information System (INIS)

    Prayitno; Djoko-Sardjono; Nurimaniwati; Adhe-Helmayani

    2000-01-01

    The influence of extractant and stirring time on the reduction componentcadmium on liquid wastes has been investigated. The method of experimentalused the extraction with liquid membrane emulsion. The parameters to beinvestigated were extractant amount tri-n octylamine (TOA), duration ofstirring time. In this investigated, extractant amount was varied from 5 to25 % (v/v) TOA, duration of stirring time varied from 5 to minutes. Theresult of experimental can be concluded that the best condition obtained forreducing cadmium component was on extractant amount 20 % (v/v) TOA, stirringtime 25 minutes. The best condition for reducing the cadmium component wasefficiency factor 98.35%. (author)

  5. Stability of levofloxacin in an extemporaneously compounded oral liquid.

    Science.gov (United States)

    VandenBussche, H L; Johnson, C E; Fontana, E M; Meram, J M

    1999-11-15

    The stability of levofloxacin in an extemporaneously compounded oral liquid was studied. A suspension of levofloxacin 50 mg/mL was prepared from commercially available 500-mg levofloxacin tablets and equal amounts of Ora-Plus and Strawberry Syrup, NF, to make a final volume of 60 mL. Six identical volumes of the suspension were prepared in amber plastic prescription bottles. Three bottles were stored at 23-25 degrees C, and three were stored at 3-5 degrees C. Immediately after preparation and at 8, 15, 29, and 57 days, samples were visually inspected and assayed in duplicate by high-performance liquid chromatography; pH was also determined. At least 99% of the initial levofloxacin concentration remained in all samples throughout the study period. The color, odor, and pH of all the samples did not change appreciably. An extemporaneously compounded oral liquid formulation of levofloxacin 50 mg/mL in a 1:1 mixture of Ora-Plus and Strawberry Syrup, NF, was stable at 23-25 or 3-5 degrees C for up to 57 days.

  6. The shape, stability and breakage of pendant liquid bridges

    Science.gov (United States)

    Padday, J. F.; Pétré, G.; Rusu, C. G.; Gamero, J.; Wozniak, G.

    1997-12-01

    Pendant liquid bridges are defined as pendant drops supporting a solid axisymmetric endplate at their lower end. The stability and shape properties of such bridges are defined in terms of the capillary properties of the system and of the mass and radius of the lower free-floating endplate. The forces acting in the pendant liquid bridge are defined exactly and expressed in dimensionless form. Numerical analysis has been used to derive the properties of a given bridge and it is shown that as the bridge grows by adding more liquid to the system a maximum volume is reached. At this maximum volume, the pendant bridge becomes unstable with the length of the bridge increasing spontaneously and irreversibly at constant volume. Finally the bridge breaks with the formation of a satellite drop or an extended thread. The bifurcation and breakage processes have been recorded using a high-speed video camera with a digital recording rate of up to 6000 frames per second. The details of the shape of the bridge bifurcation and breakage for many pendant bridge systems have been recorded and it is shown that satellite drop formation after rupture is not always viscosity dependent. Bifurcation and breakage in simulated low gravity demonstrated that breakage was very nearly symmetrical about a plane through the middle of the pendant bridge.

  7. Research results on productivity stabilization by ultrasonic camera (plant with membrane ceramic elements during vine processing

    Directory of Open Access Journals (Sweden)

    V. T. Antufyev

    2016-01-01

    Full Text Available The article describes solutions to the problems of declining productivity of ceramic membrane elements for wine processing on the final manufacturing phase. A relative stabilization of filtration velocity, venting efficiency and wine lightening were experimentally confirmed during contacts with oscillation waves of ultrasonic transmitter on the ceramic filter. Which significantly reduced the cost of various preservatives to increase periods storage. To study the processes of wine processing by the proposed method it was made an experimental installation on the basis of pilot machine MRp-1/2 for bottling of quiet liquids and an ultrasonic device "Volna– M" UZTA-1/22-OM with a firmly, waveguide which transmits sound, fixed filter frame on the ultrasound emitter. To stabilize the performance of ultrasonic units with ceramic membrane elements without quality deterioration of wines it was empirically determined rational parameters of power of ultrasound input and pressure in the system. The given derived dependencies and graphs allow to define the time of relatively stable operating filter regime. It was revealed a significant cost reduction on filtration, as it allows escape from the contamination of the product by various preservatives, and increasing of storage duration in a sealed container during aseptic filling without a thermal sterilization. Ultrasonic emitter contact by superposition wave vibrations on the ceramic filter increases not only the efficiency of gas removal, but also improves the organoleptic characteristics, stabilizes the filters, improves their productivity. Gas removal creates unfavorable conditions for development of the yeast, which in turn increases the shelf life of semisweet wine.

  8. Enhanced Membrane System for Recovery of Water from Gas-Liquid Mixtures, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Gas-Liquid separation is an acute microgravity problem. Existing devices use centrifugal motion on microporous membranes to separate the two phases. Centrifugal...

  9. Enhanced Membrane System for Recovery of Water from Gas-Liquid Mixtures Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Gas-Liquid separation is an acute microgravity problem. Existing devices use centrifugal motion on microporous membranes to separate the two phases. Centrifugal...

  10. Liquid Self-Balancing Device Effects on Flexible Rotor Stability

    Directory of Open Access Journals (Sweden)

    Leonardo Urbiola-Soto

    2013-01-01

    Full Text Available Nearly a century ago, the liquid self-balancing device was first introduced by M. LeBlanc for passive balancing of turbine rotors. Although of common use in many types or rotating machines nowadays, little information is available on the unbalance response and stability characteristics of this device. Experimental fluid flow visualization evidences that radial and traverse circulatory waves arise due to the interaction of the fluid backward rotation and the baffle boards within the self-balancer annular cavity. The otherwise destabilizing force induced by trapped fluids in hollow rotors, becomes a stabilizing mechanism when the cavity is equipped with adequate baffle boards. Further experiments using Particle Image Velocimetry (PIV enable to assess the active fluid mass fraction to be one-third of the total fluid mass. An analytical model is introduced to study the effects of the active fluid mass fraction on a flexible rotor supported by flexible supports excited by bwo different destabilizing mechanisms; rotor internal friction damping and aerodynamic cross-coupling. It is found that the fluid radial and traverse forces contribute to the balancing action and to improve the rotor stability, respectively.

  11. Membrane-stabilizing copolymers confer marked protection to dystrophic skeletal muscle in vivo

    Directory of Open Access Journals (Sweden)

    Evelyne M Houang

    Full Text Available Duchenne muscular dystrophy (DMD is a fatal disease of striated muscle deterioration. A unique therapeutic approach for DMD is the use of synthetic membrane stabilizers to protect the fragile dystrophic sarcolemma against contraction-induced mechanical stress. Block copolymer-based membrane stabilizer poloxamer 188 (P188 has been shown to protect the dystrophic myocardium. In comparison, the ability of synthetic membrane stabilizers to protect fragile DMD skeletal muscles has been less clear. Because cardiac and skeletal muscles have distinct structural and functional features, including differences in the mechanism of activation, variance in sarcolemma phospholipid composition, and differences in the magnitude and types of forces generated, we speculated that optimized membrane stabilization could be inherently different. Our objective here is to use principles of pharmacodynamics to evaluate membrane stabilization therapy for DMD skeletal muscles. Results show a dramatic differential effect of membrane stabilization by optimization of pharmacodynamic-guided route of poloxamer delivery. Data show that subcutaneous P188 delivery, but not intravascular or intraperitoneal routes, conferred significant protection to dystrophic limb skeletal muscles undergoing mechanical stress in vivo. In addition, structure-function examination of synthetic membrane stabilizers further underscores the importance of copolymer composition, molecular weight, and dosage in optimization of poloxamer pharmacodynamics in vivo.

  12. Separation of some metal ions using coupled transport supported liquid membranes

    International Nuclear Information System (INIS)

    Chaudhary, M.A.

    1993-01-01

    Liquid membrane extraction processes has become very popular due to their superiority in many ways over other separation techniques. In coupled transport membranes the metal ions can be transported across the membrane against their concentration gradient under the influence of chemical potential difference. Liquid membranes consisting of a carrier-cum-diluent, supported in microporous polymeric hydrophobic films have been studied for transport of metal ions like U(VI), Cr(VI), Be(II), V(V), Ti(IV), Zn(II), Cd(II), Hf(IV), W(VI), and Co(II). The present paper presents basic data with respect to flux and permeabilities of these metal ions across membranes based on experimental results and theoretical equations, using different carriers and diluents and provides a brief reference to possibility of such membranes for large scale applications. (author)

  13. Electrochemical detection of dopamine using arrays of liquid-liquid micro-interfaces created within micromachined silicon membranes

    International Nuclear Information System (INIS)

    Berduque, Alfonso; Zazpe, Raul; Arrigan, Damien W.M.

    2008-01-01

    The detection of protonated dopamine by differential pulse voltammetry (DPV) and square wave voltammetry (SWV) at arrays of micro-interfaces between two immiscible electrolyte solutions (μITIES) is presented. Microfabricated porous silicon membranes (consisting of eight pores, 26.6 μm in radius and 500 μm pore-pore separation, in a hexagonal layout) were prepared by photolithographic and etching procedures. The membrane pores were fabricated with hydrophobic internal walls so that the organic phase filled the pores and created the liquid interface at the aqueous side of the membrane. These were used for harnessing the benefits of three-dimensional diffusion to the interface and for interface stabilisation. The liquid-liquid interface provides a simple method to overcome the major problem in the voltammetric detection of dopamine at solid electrodes due to the co-existence of ascorbate at higher concentrations. Selectivity for dopamine over ascorbate was achieved by the use of dibenzo-18-crown-6 (DB18C6) for the facilitated ion transfer of dopamine across the μITIES array. Under these conditions, the presence of ascorbate in excess did not interfere in the detection of dopamine and the lowest concentration detectable was ca. 0.5 μM. In addition, the drawback of current signal saturation (non-linear increase of the peak current with the concentration of dopamine) observed at conventional (millimetre-sized) liquid-liquid interfaces was overcome using the microfabricated porous membranes

  14. Mathematical modeling of liquid/liquid hollow fiber membrane contactor accounting for interfacial transport phenomena: Extraction of lanthanides as a surrogate for actinides

    International Nuclear Information System (INIS)

    Rogers, J.D.

    1994-01-01

    This report is divided into two parts. The second part is divided into the following sections: experimental protocol; modeling the hollow fiber extractor using film theory; Graetz model of the hollow fiber membrane process; fundamental diffusive-kinetic model; and diffusive liquid membrane device-a rigorous model. The first part is divided into: membrane and membrane process-a concept; metal extraction; kinetics of metal extraction; modeling the membrane contactor; and interfacial phenomenon-boundary conditions-applied to membrane transport

  15. Mathematical modeling of liquid/liquid hollow fiber membrane contactor accounting for interfacial transport phenomena: Extraction of lanthanides as a surrogate for actinides

    Energy Technology Data Exchange (ETDEWEB)

    Rogers, J.D.

    1994-08-04

    This report is divided into two parts. The second part is divided into the following sections: experimental protocol; modeling the hollow fiber extractor using film theory; Graetz model of the hollow fiber membrane process; fundamental diffusive-kinetic model; and diffusive liquid membrane device-a rigorous model. The first part is divided into: membrane and membrane process-a concept; metal extraction; kinetics of metal extraction; modeling the membrane contactor; and interfacial phenomenon-boundary conditions-applied to membrane transport.

  16. Impact of Ionic Liquids on Silver Thermoplastic Composite Membrane Polyurethane for Propane/Propylene Separation

    OpenAIRE

    Wang, Yu; Yong Goh, Tee; Goodrich, Peter; Atilhan, Mert; Khraisheh, Majeda; Rooney, David; Thompson, Jillian; Jacquemin, Johan

    2017-01-01

    This work describes newly synthesized composite polymeric membranes and their utilization in propane/propylene separation in a gas mixture. The nonporous composite polymers were successfully synthesized by using thermoplastic polyurethane (TPU) and several silver salts/silver salts with ionic liquids (ILs). Our studies showed that silver bis(trifluoromethanesulfonyl)imide (Ag[Tf2N]) containing membranes outperformed other silver salt containing membranes in terms of selectivity. In addition, ...

  17. Stress-sensor device based on flexoelectric liquid crystalline membranes.

    Science.gov (United States)

    Rey, Alejandro D; Servio, Phillip; Herrera Valencia, Edtson Emilio

    2014-05-19

    Membrane flexoelectricity is an electromechanical coupling process that describes membrane bending and membrane electrical polarization caused by bending under electric fields. In this paper we propose, formulate, and characterize a stress-sensor device for mechanically loaded solids, consisting of a soft flexoelectric thin membrane attached to the loaded deformed solid. Because the curvature of the deformed solid is transferred to the attached flexoelectric membrane, the electromechanical transduction of the latter produces a charge that is proportional to the stress of the solid. The model of the stress-sensor device is based on the integration of the thermodynamics of polarizable membranes with isotropic solid elasticity, leading to a transfer function that identifies the elastic, electromechanical, and geometrical parameters involved in electrical-signal generation. The model is applied to representative normal bending and then to more complex off-axis bending of elastic bars. In all cases, a common transfer function shows the generic material and its geometric contributions. The sensor sensitivity increases linearly with flexoelectricity and the membrane-solid interface, and the sensitivity decreases with increasing membrane thickness and Young's modulus of the solid. The theoretical results contribute to ongoing experimental efforts towards the development of anisotropic soft-matter-based stress-sensor devices through solid-membrane interactions and electromechanical transduction. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Parallel artificial liquid membrane extraction of new psychoactive substances in plasma and whole blood

    DEFF Research Database (Denmark)

    Vårdal, Linda; Askildsen, Hilde-Merete; Gjelstad, Astrid

    2017-01-01

    Parallel artificial liquid membrane extraction (PALME) was combined with ultra-high performance liquid chromatography-mass spectrometry (UHPLC–MS) and the potential for screening of new psychoactive substances (NPS) was investigated for the first time. PALME was performed in 96-well format compri......, accuracy, extraction recoveries, carry-over, and matrix effects. The validation results were in accordance with FDA guidelines....

  19. Microfluidic devices as gas – Ionic liquid membrane contactors for CO2 removal from anaesthesia gases

    NARCIS (Netherlands)

    Malankowska, Magdalena; Martins, C. F.; Rho, H. S.; Neves, L. A.; Tiggelaar, R. M.; Crespo, João G.; Pina, M.P.; Mallada, R.; Gardeniers, J.G.E.; Coelhoso, I. M.

    2018-01-01

    This work proposes a microfluidic gas – ionic liquid contactor for CO2 removal from anaesthesia gas, containing Xe. The working principle involves the transport of CO2 through a polymer flat membrane followed by its capture and enzymatic bioconversion in the ionic liquid solvent. Microfluidic

  20. Hematopoietic protein-1 regulates the actin membrane skeleton and membrane stability in murine erythrocytes.

    Directory of Open Access Journals (Sweden)

    Maia M Chan

    Full Text Available Hematopoietic protein-1 (Hem-1 is a hematopoietic cell specific member of the WAVE (Wiskott-Aldrich syndrome verprolin-homologous protein complex, which regulates filamentous actin (F-actin polymerization in many cell types including immune cells. However, the roles of Hem-1 and the WAVE complex in erythrocyte biology are not known. In this study, we utilized mice lacking Hem-1 expression due to a non-coding point mutation in the Hem1 gene to show that absence of Hem-1 results in microcytic, hypochromic anemia characterized by abnormally shaped erythrocytes with aberrant F-actin foci and decreased lifespan. We find that Hem-1 and members of the associated WAVE complex are normally expressed in wildtype erythrocyte progenitors and mature erythrocytes. Using mass spectrometry and global proteomics, Coomassie staining, and immunoblotting, we find that the absence of Hem-1 results in decreased representation of essential erythrocyte membrane skeletal proteins including α- and β- spectrin, dematin, p55, adducin, ankyrin, tropomodulin 1, band 3, and band 4.1. Hem1⁻/⁻ erythrocytes exhibit increased protein kinase C-dependent phosphorylation of adducin at Ser724, which targets adducin family members for dissociation from spectrin and actin, and subsequent proteolysis. Increased adducin Ser724 phosphorylation in Hem1⁻/⁻ erythrocytes correlates with decreased protein expression of the regulatory subunit of protein phosphatase 2A (PP2A, which is required for PP2A-dependent dephosphorylation of PKC targets. These results reveal a novel, critical role for Hem-1 in the homeostasis of structural proteins required for formation and stability of the actin membrane skeleton in erythrocytes.

  1. Self-assembling peptides form nanodiscs that stabilize membrane proteins

    DEFF Research Database (Denmark)

    Midtgaard, Søren Roi; Pedersen, Martin Cramer; Kirkensgaard, Jacob Judas Kain

    2014-01-01

    New methods to handle membrane bound proteins, e.g. G-protein coupled receptors (GPCRs), are highly desirable. Recently, apoliprotein A1 (ApoA1) based lipoprotein particles have emerged as a new platform for studying membrane proteins, and it has been shown that they can self-assemble in combinat......New methods to handle membrane bound proteins, e.g. G-protein coupled receptors (GPCRs), are highly desirable. Recently, apoliprotein A1 (ApoA1) based lipoprotein particles have emerged as a new platform for studying membrane proteins, and it has been shown that they can self...

  2. Gas-liquid membrane contactors for CO2 removal

    NARCIS (Netherlands)

    Simons-Fischbein, K.; Nijmeijer, Dorothea C.; Wessling, Matthias

    2009-01-01

    In the present work we use a membrane contactor for the separation of CO2 from CH4 and we systematically investigate the influence of both the type of membrane and the different process parameters on the overall process performance (permeability and selectivity). This work is important because it

  3. Parallel artificial liquid membrane extraction as an efficient tool for removal of phospholipids from human plasma

    DEFF Research Database (Denmark)

    Ask, Kristine Skoglund; Bardakci, Turgay; Parmer, Marthe Petrine

    2016-01-01

    Generic Parallel Artificial Liquid Membrane Extraction (PALME) methods for non-polar basic and non-polar acidic drugs from human plasma were investigated with respect to phospholipid removal. In both cases, extractions in 96-well format were performed from plasma (125μL), through 4μL organic...... solvent used as supported liquid membranes (SLMs), and into 50μL aqueous acceptor solutions. The acceptor solutions were subsequently analysed by liquid chromatography-tandem mass spectrometry (LC-MS/MS) using in-source fragmentation and monitoring the m/z 184→184 transition for investigation...

  4. Triple-bore hollow fiber membrane contactor for liquid desiccant based air dehumidification

    KAUST Repository

    Bettahalli Narasimha, Murthy Srivatsa

    2016-04-26

    Dehumidification is responsible for a large part of the energy consumption in cooling systems in high humidity environments worldwide. Improving efficiency is therefore essential. Liquid desiccants offer a promising solution for dehumidification, as desired levels of humidity removal could be easily regulated. The use of membrane contactors in combination with liquid desiccant is attractive for dehumidification because they prevent direct contact between the humid air and the desiccant, removing both the potential for desiccant carryover to the air and the potential for contamination of the liquid desiccant by dust and other airborne materials, as well as minimizing corrosion. However, the expected additional mass transport barrier of the membrane surface can lower the expected desiccation rate per unit of desiccant surface area. In this context, hollow fiber membranes present an attractive option for membrane liquid desiccant contactors because of their high surface area per unit volume. We demonstrate in this work the performance of polyvinylidene fluoride (PVDF) based triple-bore hollow fiber membranes as liquid desiccant contactors, which are permeable to water vapor but impermeable to liquid water, for dehumidification of hot and humid air.

  5. Ionic Liquids As Self-Assembly Guide for the Formation of Nanostructured Block Copolymer Membranes

    KAUST Repository

    Madhavan, Poornima

    2015-04-30

    Nanostructured block copolymer membranes were manufactured by water induced phase inversion, using ionic liquids (ILs) as cosolvents. The effect of ionic liquids on the morphology was investigated, by using polystyrene-b-poly(4-vinyl pyridine) (PS-b-PV4P) diblock as membrane copolymer matrix and imidazolium and pyridinium based ILs. The effect of IL concentration and chemical composition was evident with particular interaction with P4VP blocks. The order of block copolymer/ILs solutions previous to the membrane casting was confirmed by cryo scanning electron microscopy and the morphologies of the manufactured nanostructured membranes were characterized by transmission and scanning electron microscopy. Non-protic ionic liquids facilitate the formation of hexagonal nanoporous block copolymer structure, while protic ILs led to a lamella-structured membrane. The rheology of the IL/block copolymer solutions was investigated, evaluating the storage and loss moduli. Most membranes prepared with ionic liquid had higher water flux than pure block copolymer membranes without additives.

  6. Stability of norfloxacin in an extemporaneously prepared oral liquid.

    Science.gov (United States)

    Johnson, C E; Price, J; Hession, J M

    2001-04-01

    The stability of norfloxacin in an extemporaneously prepared suspension stored at room temperature and under refrigeration was studied over 56 days. A 20-mg/mL suspension was prepared from commercially available 400-mg norfloxacin tablets and equal amounts of Ora-Plus and strawberry syrup to make a final volume of 60 mL. Six identical samples of the suspension were prepared in amber plastic prescription bottles. Three were stored at room temperature (23-25 degrees C) and three under refrigeration (3-5 degrees C). Immediately after preparation and at 7, 14, 28, and 56 days, the samples were assayed in duplicate by stability-indicating high performance liquid chromatography. The samples were also inspected for color and odor changes and the pH of each sample was determined. At least 93% of the initial norfloxacin concentration remained throughout the 56-day study period. The color, odor, and pH of all of the samples did not change appreciably. An extemporaneously prepared suspension of norfloxacin 20 mg/mL was stable for at least 56 days when stored at either 23-25 or 3-5 degrees C.

  7. Reverse osmosis molecular differentiation of organic liquids using carbon molecular sieve membranes

    Science.gov (United States)

    Koh, Dong-Yeun; McCool, Benjamin A.; Deckman, Harry W.; Lively, Ryan P.

    2016-08-01

    Liquid-phase separations of similarly sized organic molecules using membranes is a major challenge for energy-intensive industrial separation processes. We created free-standing carbon molecular sieve membranes that translate the advantages of reverse osmosis for aqueous separations to the separation of organic liquids. Polymer precursors were cross-linked with a one-pot technique that protected the porous morphology of the membranes from thermally induced structural rearrangement during carbonization. Permeation studies using benzene derivatives whose kinetic diameters differ by less than an angstrom show kinetically selective organic liquid reverse osmosis. Ratios of single-component fluxes for para- and ortho-xylene exceeding 25 were observed and para- and ortho- liquid mixtures were efficiently separated, with an equimolar feed enriched to 81 mole % para-xylene, without phase change and at ambient temperature.

  8. Application of reverse osmosis membrane technology for liquid radioactive waste processing

    International Nuclear Information System (INIS)

    Zhao Juan

    2010-01-01

    Liquid radioactive waste (LRW) processing should bear an acceptable level of residual radioactivity for discharge and meet the request of energy saving and waste minimization. Reverse osmosis (RO) membrane technology has been developed as a novel process for LRW processing. Five basic operating parameters of flux, recovery factor, rejection factor, concentration factor and decontamination factor were described, and the latter two parameters were the most important. Concentration factor and decontamination factor should be as high as possible and simultaneously the operating cost for membrane filtration should be low. Technical design considerations for membrane process were discussed and optimized from the aspects of pretreatment, membrane module choice and arrangement and membrane clear out. Application and investigation of RO membrane technology for LRW processing were introduced and it should be noted that the RO membrane technology has been introduced into overseas nuclear power plants for LRW processing and interiorly in the stage of investigation. (authors)

  9. Separation of Gas Mixtures by New Type of Membranes – Dynamic Liquid Membranes.

    OpenAIRE

    Setničková, K. (Kateřina); Šíma, V. (Vladimír); Petričkovič, R. (Roman); Řezníčková Čermáková, J. (Jiřina); Uchytil, P. (Petr)

    2016-01-01

    The selectivity and permeability of membrane material determines the efficiency of the gas separation process. To prepare a stable high selective and high permeable membrane and, in addition, also cheap, is the dream of most scientists dealing with the membrane technology. We proposed to investigate the gas separation by a completely new type of membranes possessing both; high selectivity and high gas permeability. Our preliminary results are very promising. We are able to prepare a very chea...

  10. Efficient gas-liquid contact using microfluidic membrane devices with staggered herringbone mixers.

    Science.gov (United States)

    Femmer, Tim; Eggersdorfer, Max L; Kuehne, Alexander J C; Wessling, Matthias

    2015-08-07

    We describe a novel membrane based gas-liquid-contacting device with increased mass transport and reduced pressure loss by combining a membrane with a staggered herringbone static mixer. Herringbone structures are imposed on the microfluidic channel geometry via soft lithography, acting as mixers which introduce secondary flows at the membrane interface. Such flows include Dean vortices and Taylor flows generating effective mixing while improving mass transport and preventing concentration polarization in microfluidic channels. Furthermore, our static herringbone mixer membranes effectively reduce pressure losses leading to devices with enhanced transfer properties for microfluidic gas-liquid contact. We investigate the red blood cell distribution to tailor our devices towards miniaturised extracorporeal membrane oxygenation and improved comfort of patients with lung insufficiencies.

  11. Microporous hollow fibre membrane modules as gas-liquid contactors. Part 1: Physical mass transfer processes. A specific application: mass transfer in highly viscous liquids

    NARCIS (Netherlands)

    Kreulen, H.; Kreulen, H.; Versteeg, Geert; Smolders, C.A.; Smolders, C.A.; van Swaaij, Willibrordus Petrus Maria

    1993-01-01

    Gas-liquid mass transfer has been studied in a membrane module with non-wetted microporous fibres in the laminar flow regime. This new type of gas/liquid contactor can be operated stabily over a large range of gas and liquid flows because gas and liquid phase do not influence each other directly.

  12. Colour-Value Based Method for Polydopamine Coating-Stability Characterization on Polyethersulfone Membranes

    Directory of Open Access Journals (Sweden)

    Thomas Bucher

    2017-12-01

    Full Text Available Porous polyethersulfone membranes as used in oenology were investigated in order to evaluate temperature-dependent permeances in a temperature range from 10 to 35 °C. A temperature correction factor was determined for this type of membrane to get accurate and comparable results for further developments. Moreover, the membranes were modified with a bio-inspired polydopamine coating in order to reduce fouling. The performance of the membranes could be increased with respect to permeance and flux recovery under cross-flow conditions. In order to test the applicability and stability of the coating layer, they were treated with basic and acidic cleaning agents as used in industry for fouled membranes. The chemical stability of the coating layer was studied under basic and acidic conditions, by systematic observation of the colour change of the coated membranes over treatment time.

  13. Colour-Value Based Method for Polydopamine Coating-Stability Characterization on Polyethersulfone Membranes.

    Science.gov (United States)

    Bucher, Thomas; Clodt, Juliana I; Grabowski, Andrej; Hein, Martin; Filiz, Volkan

    2017-12-16

    Porous polyethersulfone membranes as used in oenology were investigated in order to evaluate temperature-dependent permeances in a temperature range from 10 to 35 °C. A temperature correction factor was determined for this type of membrane to get accurate and comparable results for further developments. Moreover, the membranes were modified with a bio-inspired polydopamine coating in order to reduce fouling. The performance of the membranes could be increased with respect to permeance and flux recovery under cross-flow conditions. In order to test the applicability and stability of the coating layer, they were treated with basic and acidic cleaning agents as used in industry for fouled membranes. The chemical stability of the coating layer was studied under basic and acidic conditions, by systematic observation of the colour change of the coated membranes over treatment time.

  14. Signal Processing Methods for Liquid Rocket Engine Combustion Spontaneous Stability and Rough Combustion Assessments

    Science.gov (United States)

    Kenny, R. Jeremy; Casiano, Matthew; Fischbach, Sean; Hulka, James R.

    2012-01-01

    Liquid rocket engine combustion stability assessments are traditionally broken into three categories: dynamic stability, spontaneous stability, and rough combustion. This work focuses on comparing the spontaneous stability and rough combustion assessments for several liquid engine programs. The techniques used are those developed at Marshall Space Flight Center (MSFC) for the J-2X Workhorse Gas Generator program. Stability assessment data from the Integrated Powerhead Demonstrator (IPD), FASTRAC, and Common Extensible Cryogenic Engine (CECE) programs are compared against previously processed J-2X Gas Generator data. Prior metrics for spontaneous stability assessments are updated based on the compilation of all data sets.

  15. Electrokinetic migration across artificial liquid membranes. New concept for rapid sample preparation of biological fluids.

    Science.gov (United States)

    Pedersen-Bjergaard, Stig; Rasmussen, Knut Einar

    2006-03-24

    Basic drug substances were transported across a thin artificial organic liquid membrane by the application of 300 V d.c. From a 300 microl aqueous donor compartment (containing 10 mM HCl), the drugs migrated through a 200 microm artificial liquid membrane of 2-nitrophenyl octyl ether immobilized in the pores of a polypropylene hollow fiber, and into a 30 microl aqueous acceptor solution of 10 mM HCl inside the lumen of the hollow fiber. The transport was forced by an electrical potential difference sustained over the liquid membrane, resulting in electrokinetic migration of drug substances from the donor compartment to the acceptor solution. Within 5 min of operation at 300 V, pethidine, nortriptyline, methadone, haloperidol, and loperamide were extracted with recoveries in the range 70-79%, which corresponded to enrichments in the range 7.0-7.9. The chemical composition of the organic liquid membrane strongly affected the permeability, and may serve as an efficient tool for controlling the transport selectivity. Water samples, human plasma, and human urine were successfully processed, and in light of the present report, electrokinetic migration across thin artificial liquid membranes may be an interesting tool for future isolation within chemical analysis.

  16. Roles of metal ion complexation and membrane permeability in the metal flux through lipophilic membranes. Labile complexes at permeation liquid membranes

    NARCIS (Netherlands)

    Zhang, Z.; Buffle, J.; Leeuwen, van H.P.; Wojciechowski, K.

    2006-01-01

    The various physicochemical factors that influence the flux of carrier-transported metal ions through permeation liquid membranes (PLM) are studied systematically. Understanding PLM behavior is important (i) to optimize the application of PLM as metal speciation sensors in environmental media and

  17. chemical studies on the extraction of certain metal ions from aqueous solution by liquid emulsion membrane

    International Nuclear Information System (INIS)

    Kassem, A.T.

    2011-01-01

    In this thesis four systems are addressed related to the use of liquid emulsion membranes (ELM) based on Co(III)dicarbiolide and. The system was dedicated for permeation of cadmium , cobalt Nickel and lead for use of this system for preconcentration and separation of cadmium, cobalt, nickel and lead. The work carried out in this thesis is presented in three parts, namely; introduction, experimental and results and discussion.The first chapter is the introduction which includes aim of work, basic concepts of liquid membranes; liquid emulsion membranes; different models of emulsion permeation, literature survey of extraction chemistry of cadmium, cobalt, nickel and lead. Chapter two includes the experimental part. In this part detailed outlines on the chemicals and different elements used were given. Different instruments as well as analytical techniques were outlines. The preparation of liquid emulsion membrane and the permeation techniques were presented in details. The third chapter deals with the results and discussion. This chapter is divided into four main parts, the four parts is concerned with cadmium/Co(III) dicarbolide/NTA, EDTA, DPTA and DCTA systems. In this part the permeation of Cd(II) aqueous solution by the membrane used was experimented based on liquid-liquid extraction studies of cadmium from different sodium chloride molarities (from 0.01 to 0.1 M) by 0.01 M Cobalt(III) dicarbolides. It was found that the extraction of with cadmium is higher following in the first system, the permeation of the toxic elements, Cd(II) from HCl/sodium chloride medium was carried out using liquid emulsion membrane containing Co(III)dicarbiolide in xylene as carrier, Spain 80/ Spain 85(1:3) as surfactant and NTA, EDTA, DPTA and DCTA as a stripping solutions.

  18. One-step extraction of polar drugs from plasma by parallel artificial liquid membrane extraction.

    Science.gov (United States)

    Pilařová, Veronika; Sultani, Mumtaz; Ask, Kristine Skoglund; Nováková, Lucie; Pedersen-Bjergaard, Stig; Gjelstad, Astrid

    2017-02-01

    The new microextraction technique named parallel artificial liquid membrane extraction (PALME) was introduced as an alternative approach to liquid-liquid extraction of charged analytes from aqueous samples. The concept is based on extraction of analytes across a supported liquid membrane sustained in the pores of a thin polymeric membrane, a well-known extraction principle also used in hollow fiber liquid-phase microextraction (HF-LPME). However, the new PALME technique offers a more user-friendly setup in which the supported liquid membrane is incorporated in a 96 well plate system. Thus, high-throughput is achievable, in addition to the green chemistry offered by using PALME. The consumption of organic solvent is minimized to 3-5μL per sample. With a sample volume of 250μL and acceptor solution volume of 50μL, a maximal enrichment factor of five is achievable. Based on these parameters, a new method for extraction of polar basic drugs was developed in the present work. The basic drugs hydralazine, ephedrine, metaraminol, salbutamol, and cimetidine were used as model analytes, and were extracted from alkalized human plasma into an aqueous solution via the supported liquid membrane. The extraction was promoted by a carrier dissolved in the membrane, creating a temporary ion-pair complex between the hydrophilic drug and the carrier. As the model analytes were extracted directly into an aqueous solution, there was no need for evaporation of the extract before injection into LC-MS. Hence, the sample preparation is performed in one step. With optimized conditions, the extraction recoveries were in the range 50-89% from human plasma after 45min extraction. The data from the method evaluation were satisfactory and in line with current guidelines, and revealed an extraction method with substantial potential for high throughput bioanalysis of polar basic drugs. Copyright © 2016 Elsevier B.V. All rights reserved.

  19. Stability of DNA-tethered lipid membranes with mobile tethers.

    Science.gov (United States)

    Chung, Minsub; Boxer, Steven G

    2011-05-03

    We recently introduced two approaches for tethering planar lipid bilayers as membrane patches to either a supported lipid bilayer or DNA-functionalized surface using DNA hybridization (Chung, M.; Lowe, R. D.; Chan, Y-H. M.; Ganesan, P. V.; Boxer, S. G. J. Struct. Biol.2009, 168, 190-9). When mobile DNA tethers are used, the tethered bilayer patches become unstable, while they are stable if the tethers are fixed on the surface. Because the mobile tethers between a patch and a supported lipid bilayer offer a particularly interesting architecture for studying the dynamics of membrane-membrane interactions, we have investigated the sources of instability, focusing on membrane composition. The most stable patches were made with a mixture of saturated lipids and cholesterol, suggesting an important role for membrane stiffness. Other factors such as the effect of tether length, lateral mobility, and patch membrane edge were also investigated. On the basis of these results, a model for the mechanism of patch destruction is developed.

  20. Characterization of carbon dioxide transfer in a hollow fiber membrane module as a solution for gas-liquid transfer in microgravity conditions.

    Science.gov (United States)

    Farges, Berangere; Duchez, David; Dussap, Claude-Gilles; Cornet, Jean-F.

    In microgravity, one of the major difficulties encountered in closed photosynthetic reactors is the gas-liquid transfer with the necessity to provide CO2 (carbon source, pH control) and to recover the produced O2 . Indeed, reduced gravity is expected to modify gas liquid transfer and liquid phase mixing characteristics inside photobioreactors conceived to regenerate atmosphere of closed life-support systems. To obtain efficient mass transfer conditions and mixing of phases, several solutions are possible: use of rotating reactor (centrifugal field), use of forced, co-current convective reactor with gas-liquid separator and use of membrane modules. In terms of space process engineering, the membrane reactor can be a valuable alternative in which the gas and liquid phases are separated with a selectively permeable membrane. The rate-limiting factors in this reactor were demonstrated to be the surface of membrane A needed for diffusion of gases and the CO2 and O2 mass transfer coefficients in the liquid phase kL. How-ever, the major advantages of the membrane reactor are that it is composed of a hydrophobic membrane (here PTFE) which showed a high hydrophobicity, an important chemical resis-tance, a very long term stability and overall which is favourable to gas transfer. Moreover, the volumetric mass transfer coefficients are sufficiently high to build compact systems with small footprints, no complex rotating devices and lighter weights. This paper describes first the development of a system enabling the accurate characterization of the mass transfer limiting step for a PTFE membrane module. This original technical apparatus, together with a technical assessment of membrane permeability to different gases, is associated with a balance model, determining thus completely the CO2 mass transfer problem between phases. First results are given and discussed for the CO2 mass transfer coefficient CO kL 2 obtained in case of an absorption experiment at pH = 8 using the

  1. The Impact of Sloshing Liquids on Ship Stability for Various Dimensions of Partly Filled Tanks

    Directory of Open Access Journals (Sweden)

    Przemyslaw Krata

    2013-12-01

    Full Text Available Liquid sloshing phenomenon taking place in partly filled ships’ tanks directly affects the stability of a vessel. However, only static calculations are carried out onboard ships nowadays and static transfer of liquid weight is taken into account in the course of routine stability calculation. The paper is focused on a dynamic heeling moment due to liquid sloshing in tanks onboard ships. A number of numerical simulations of liquid sloshing taking place in a moving tank is carried out. The wide range of ship’s tanks is taken into account. The conducted CFD simulations are experimentally verified. Finally, the method of an assessment of the liquid sloshing impact on ship transverse stability is worked out. The key point of the method is a dynamic coefficient describing relation of the researched dynamic heeling moment and the quasi-static one in terms of dynamic stability of a vessel which is related to the weather criterion of ship stability assessment.

  2. Chitosan/Carboxymethylcellulose/Ionic Liquid/Ag(0 Nanoparticles Form a Membrane with Antimicrobial Activity

    Directory of Open Access Journals (Sweden)

    Camila Quadros

    2013-01-01

    Full Text Available Silver metal nanoparticles were immobilized in chitosan/carboxymethylcellulose/BMI.BF4(1-n-butyl-3-methylimidazolium tetrafluoroborate ionic liquid (CS/CMC/IL to form polymeric membrane with 20 μm thickness. The CS/CMC/IL polymeric membrane was prepared using a simple solution blending method. Irregularly shaped Ag(0 nanoparticles with monomodal size distributions of 8.0±0.4 nm Ag(0 were immobilized in the membrane. The presence of small Ag(0 nanoparticles induced an augmentation in the CS/CMC/IL film surface areas. The CS/CMC/IL membrane containing Ag(0 showed increase antimicrobial activity the Ag(0 concentration increased up to saturation at 10 mg. CS/CMC/IL membrane that contains Ag(0 nanoparticles has enhanced durability of the membrane and exhibited stronger antimicrobial activity against Escherichia coli and Staphylococcus aureus.

  3. Standard Practice for Processing Aerospace Liquid Samples for Particulate Contamination Analysis Using Membrane Filters

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2008-01-01

    1.1 This practice covers the processing of liquids in preparation for particulate contamination analysis using membrane filters and is limited only by the liquid-to-membrane filter compatibility. 1.2 The practice covers the procedure for filtering a measured volume of liquid through a membrane filter. When this practice is used, the particulate matter will be randomly distributed on the filter surface for subsequent contamination analysis methods. 1.3 The practice describes procedures to allow handling particles in the size range between 2 and 1000 μm with minimum losses during handling. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

  4. Extraction of lithium ion from alkaline aqueous media by a liquid surfactant membrane

    International Nuclear Information System (INIS)

    Kinugasa, Takumi; Ono, Yuri; Kawamura, Yuko; Watanabe, Kunio; Takeuchi, Hiroshi.

    1995-01-01

    Extraction of lithium ion from aqueous alkaline media by a liquid surfactant membrane was performed using a mixture of LIX54 and TOPO as the extractant. Stripping of lithium from the kerosene solution to the acid solution was suppressed with increasing content of polyamine (ECA) surfactant. The extraction rate of lithium by the liquid membrane could be interpreted taking account of an interfacial resistance due to ECA. It was confirmed that swelling of the (W/O) emulsion drops by water permeation through the liquid membrane is evaluated in terms of a change in osmotic pressure gradient between the external and internal aqueous phases during the lithium extraction. In the present operation, the extraction ratio of Li + from the external feed and the uptake into the internal phase reached as high as 95%. (author)

  5. Porous Poly(Ionic Liquid) Membranes as Efficient and Recyclable Absorbents for Heavy Metal Ions.

    Science.gov (United States)

    Ren, Yongyuan; Zhang, Jiandong; Guo, Jiangna; Chen, Fei; Yan, Feng

    2017-07-01

    Heavy metal ion pollution has become a serious environmental problem. Herein, this study reports the synthesis of poly(ionic liquid) (PIL) membranes via in situ photo-crosslinking of vinyl imidazole with both hydrophilic and hydrophobic ionic liquid monomers. The resultant amphiphilic polymer membranes are porous and exhibit high absorption capacity of metal ions (including Hg 2+ , Pb 2+ , Cu 2+ , Cd 2+ , and Zn 2+ ) in both high (1000 mg L -1 ) and low (10 mg L -1 ) concentration metal ion solutions. These metal ionic absorption membranes are easily regenerated in acid solution and can be reused without significant decreases of absorption capacity after many cycles. These PIL membranes may have potential applications as eco-friendly and safe heavy metal ion removal materials. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. Cyclic Voltammetry of Biopolymer Heparin at PVC Plasticized Liquid Membrane

    Czech Academy of Sciences Publication Activity Database

    Samec, Zdeněk; Trojánek, Antonín; Langmaier, Jan; Samcová, E.

    2003-01-01

    Roč. 5, - (2003), s. 867-870 ISSN 1388-2481 R&D Projects: GA ČR GA203/04/0424 Institutional research plan: CEZ:AV0Z4040901 Keywords : cyclic voltammetry * PVC plasticized liquit membrane * heparin Subject RIV: CG - Electrochemistry Impact factor: 2.300, year: 2003

  7. Chemical stability of enalapril maleate drug substance and tablets by a stability-indicating liquid chromatographic method

    OpenAIRE

    Diego,Marta de; Godoy,Gloria; Mennickent,Sigrid; Godoy,Ricardo

    2011-01-01

    The chemical stability of enalapril drug substance and tablets was studied by a stability-indicating liquid chromatographic method. Stress testing was performed on drug substance under various conditions. Accelerated stability testing was carried out for different formulations of enalapril tablets. Chromatographic separation was achieved on a RP-18 column, using a mobile phase of methanol phosphate buffer at 1.0 mL min"1 and UV detection. Degradation of the drug substance was greater under hy...

  8. Microporous hollow fibre membrane modules as gas-liquid contactors. Part 1. Physical mass transfer processes : A specific application

    NARCIS (Netherlands)

    Kreulen, H.; Versteeg, G.F.; Swaaij, W.P.M. van

    1993-01-01

    Gas-liquid mass transfer has been studied in a membrane module with non-wetted microporous fibres in the laminar flow regime. This new type of gas/liquid contactor can be operated stabily over a large range of gas and liquid flows because gas and liquid phase do not influence each other directly.

  9. Electrospun polymer membrane activated with room temperature ionic liquid: Novel polymer electrolytes for lithium batteries

    Science.gov (United States)

    Cheruvally, Gouri; Kim, Jae-Kwang; Choi, Jae-Won; Ahn, Jou-Hyeon; Shin, Yong-Jo; Manuel, James; Raghavan, Prasanth; Kim, Ki-Won; Ahn, Hyo-Jun; Choi, Doo Seong; Song, Choong Eui

    A new class of polymer electrolytes (PEs) based on an electrospun polymer membrane incorporating a room-temperature ionic liquid (RTIL) has been prepared and evaluated for suitability in lithium cells. The electrospun poly(vinylidene fluoride- co-hexafluoropropylene) P(VdF-HFP) membrane is activated with a 0.5 M solution of LiTFSI in 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide (BMITFSI) or a 0.5 M solution of LiBF 4 in 1-butyl-3-methylimidazolium tetrafluoroborate (BMIBF 4). The resulting PEs have an ionic conductivity of 2.3 × 10 -3 S cm -1 at 25 °C and anodic stability at >4.5 V versus Li +/Li, making them suitable for practical applications in lithium cells. A Li/LiFePO 4 cell with a PE based on BMITFSI delivers high discharge capacities when evaluated at 25 °C at the 0.1 C rate (149 mAh g -1) and the 0.5 C rate (132 mAh g -1). A very stable cycle performance is also exhibited at these low current densities. The properties decrease at the higher, 1 C rate, when operated at 25 °C. Nevertheless, improved properties are obtained at a moderately elevated temperature of operation, i.e. 40 °C. This is attributed to enhanced conductivity of the electrolyte and faster reaction kinetics at higher temperatures. At 40 °C, a reversible capacity of 140 mAh g -1 is obtained at the 1 C rate.

  10. Development of advanced membrane process for treatment of radioactive liquid wastes

    International Nuclear Information System (INIS)

    Lee, Kune Woo; Choi, W. K.; Lee, J. W.; Jung, G. H.

    2002-01-01

    The followings were studied through the project entitled 'Development of advanced membrane process for treatment of radioactive liquid wastes'. 1. Surface modification technique of microfiltration membrane. Microporous hydrophobic polypropylene(PP) membrane were modified by radiation-induced grafting using hydrophilic monomers such as arylic acid(AAc), 2-hydroxyethyl methacrylate(HEMA) and styrenesulfonic acid(SSS). The effect of grafting conditions was investigated. Also, copolymeric condition of AAc and EGDMA for nylon membrane was studied. The structure of grafted PP membrane was examined by using FTIR-ATR spectroscopy, SEM and contact angle. The grafted membrane was characterized by measureing the water flux, the ion exchange capacity or the binding capacity of the metal ions. A study on the permeation behavior of simulated waste water containing oil emulsion and characterization of membrane fouling was carried out in the crossflow membrane filtration process using capillary type PP microfiltration membrane modified by radiation induced grafting of HEMA. The effects of various operating parameters were investigated. 2. Electrofiltration Technology. In this section, the process conditions for fouling prevention of membrane by evaluating the effects of operational parameters such as external electric field strength, crossflow velocity, transmembrane pressure, etc. on the permeate flux in electrofiltration were established and the process applicability for oil emulsion wastes containing surfactant using parallel plate type electrofiltration module was evaluated

  11. Descemet′s membrane detachment managed with perfluro-n-octane liquid

    Directory of Open Access Journals (Sweden)

    M Ashok Kumar

    2012-01-01

    Full Text Available We report the case of a 68-year-old male who developed Descemet′s membrane detachment after temporal clear corneal phacoemulsification which did not settle with air or viscoelastic injection. The Descemet′s membrane was successfully reattached with restoration of 20/50 vision with the help of perfluro-n-octane liquid. To our knowledge, this is the first such case to be reported.

  12. Membrane protein stoichiometry studied in intact mammalian cells using liquid-phase electron microscopy.

    Science.gov (United States)

    DE Jonge, N

    2018-02-01

    Receptor membrane proteins in the plasma membranes of cells respond to extracellular chemical signals by conformational changes, spatial redistribution, and (re-)assembly into protein complexes, for example, into homodimers (pairs of the same protein type). The functional state of the proteins can be determined from information about how subunits are assembled into protein complexes. Stoichiometric information about the protein complex subunits, however, is generally not obtained from intact cells but from pooled material extracted from many cells, resulting in a lack of fundamental knowledge about the functioning of membrane proteins. First, functional states may dramatically differ from cell to cell on account of cell heterogeneity. Second, extracting the membrane proteins from the plasma membrane may lead to many artefacts. Liquid-phase scanning transmission electron microscopy (STEM), in short liquid STEM, is a new technique capable of determining the locations of individual membrane proteins within the intact plasma membranes of cells in liquid. Many tens of whole cells can readily be imaged. It is possible to analyse the stoichiometry of membrane proteins in single cells while accounting for heterogenic cell populations. Liquid STEM was used to image epidermal growth factor receptors in whole COS7 cells. A study of the dimerisation of the HER2 protein in breast cancer cells revealed the presence of rare cancer cells in which HER2 was in a different functional state than in the bulk cells. Stoichiometric information about receptors is essential not only for basic science but also for biomedical application because they present many important pharmaceutical targets. © 2017 The Authors Journal of Microscopy © 2017 Royal Microscopical Society.

  13. Transport of europium(III) through supported liquid membrane containing diisodecylphosphoric acid

    International Nuclear Information System (INIS)

    Akiba, Kenichi; Nakamura, Shigeto

    1987-01-01

    The transport of europium has been investigated through a supported liquid membrane containing diisodecylphosphoric acid (DIDPA). By the addition of 1-octanol to the membrane phase, europium was quantitatively transported from the feed solution of 0.1 M HNO 3 into the product solution of 5 M HNO 3 . The apparent rate constant (k obs ) increased with increasing carrier concentration and became nearly constant above 0.05 M DIDPA. (author)

  14. Optimization of methylene blue removal by stable emulsified liquid membrane using Plackett–Burman and Box–Behnken designs of experiments

    Science.gov (United States)

    Djenouhat, Meriem; Bendebane, Farida; Bahloul, Lynda; Samar, Mohamed E. H.

    2018-01-01

    The stability of an emulsified liquid membrane composed of Span80 as a surfactant, D2EHPA as an extractant and sulfuric acid as an internal phase was first studied according to different diluents and many operating parameters using the Plackett–Burman design of experiments. Then the removal of methylene blue from an aqueous solution has been carried out using this emulsified liquid membrane at its stability conditions. The effects of operating parameters were analysed from the Box–Behnken design of experiments. The optimization of the extraction has been realized applying the response surface methodology and the results showed that the dye extraction yielding 98.72% was achieved at optimized conditions. PMID:29515841

  15. Optimization of methylene blue removal by stable emulsified liquid membrane using Plackett-Burman and Box-Behnken designs of experiments.

    Science.gov (United States)

    Djenouhat, Meriem; Bendebane, Farida; Bahloul, Lynda; Samar, Mohamed E H; Ismail, Fadhel

    2018-02-01

    The stability of an emulsified liquid membrane composed of Span80 as a surfactant, D2EHPA as an extractant and sulfuric acid as an internal phase was first studied according to different diluents and many operating parameters using the Plackett-Burman design of experiments. Then the removal of methylene blue from an aqueous solution has been carried out using this emulsified liquid membrane at its stability conditions. The effects of operating parameters were analysed from the Box-Behnken design of experiments. The optimization of the extraction has been realized applying the response surface methodology and the results showed that the dye extraction yielding 98.72% was achieved at optimized conditions.

  16. A new approach to the spectral analysis of liquid membrane oscillators by Gábor transformation

    DEFF Research Database (Denmark)

    Płocharska-Jankowska, E.; Szpakowska, M.; Mátéfi-Tempfli, Stefan

    2006-01-01

    is presented here based on Gábor transformation allowing one to obtain power spectra of any kind of oscillations that can be met experimentally. The proposed Gábor analysis is applied to a liquid membrane oscillator containing a cationic surfactant. It was found that the power spectra are strongly influenced......Liquid membrane oscillators very frequently have an irregular oscillatory behavior. Fourier transformation cannot be used for these nonstationary oscillations to establish their power spectra. This important point seems to be overlooked in the field of chemical oscillators. A new approach...

  17. Possible applications of crown-ethers to metal extraction using liquid membrane technology - a literature survey

    International Nuclear Information System (INIS)

    Dozol, M.

    1990-01-01

    Ether-crowns, discovered in 1967 by J.C. PEDERSEN, exhibit attractive complexive and extractive properties, enhanced in various fields, such as analytical chemistry, chemical synthesis, field of biology, or extractive chemistry. The investigations carried out on these macrocyclic compounds are continually increasing, as show in international literature. Among the focus of interest, the applications to metal extraction are extensively studied with crown compounds present in liquid phase or impregnated on supports (membranes or resins). The goal of this paper is to describe the application of crown-ethers to metal extraction, using liquid membrane processes. 69 refs

  18. Geometric methods in the elastic theory of membranes in liquid crystal phases

    CERN Document Server

    Ji Xing Liu; Yu Zhang Xie

    1999-01-01

    This book contains a comprehensive description of the mechanical equilibrium and deformation of membranes as a surface problem in differential geometry. Following the pioneering work by W Helfrich, the fluid membrane is seen as a nematic or smectic - A liquid crystal film and its elastic energy form is deduced exactly from the curvature elastic theory of the liquid crystals. With surface variation the minimization of the energy at fixed osmotical pressure and surface tension gives a completely new surface equation in geometry that involves potential interest in mathematics. The investigations

  19. The use of supported liquid membranes in the treatment of mining effluents

    International Nuclear Information System (INIS)

    Hebden, D.; Smit, J.J.

    1984-01-01

    The acid barren effluents from uranium extraction plants contain a number of dissolved metals although these are often only in trace concentrations. Whilst recovery of these minerals for economic gain has been considered in the past, the removal of some of these minerals is now even more desirable in view of environmental considerations. It is in this application that the supported liquid membrane system finds a model application, with its ability to treat large volumes of unclarified waters, with minimal solvent losses, and selectivity of ion removal. This paper presents current research into this supported liquid membrane application and reviews techniques and costs, in the light of present knowledge. (author)

  20. Parallel artificial liquid membrane extraction of psychoactive analytes: a novel approach in therapeutic drug monitoring.

    Science.gov (United States)

    Olsen, Katharina Norgren; Ask, Kristine Skoglund; Pedersen-Bjergaard, Stig; Gjelstad, Astrid

    2018-03-01

    Liquid-liquid extraction is widely used in therapeutic drug monitoring of antipsychotics, but difficulties in automation of the technique can result in long operational time. In this paper, parallel artificial liquid membrane extraction was used for extraction of serotonin- and serotonin-norepinephrine reuptake inhibitors from human plasma, and an approach to automate the technique was investigated. Eight model analytes were extracted from 125 μl human plasma with recoveries in the range 72-111% (relative standard deviation [RSD] ≤12.8%). A semiautomated pipettor was successfully utilized in the procedure, reducing the manual handling time. Real patient samples were analyzed with satisfying accuracy. A semiautomated extraction of serotonin-and serotonin-norepinephrine reuptake inhibitors by parallel artificial liquid membrane extraction extraction was successfully performed.

  1. Indirect evaporative cooler using membrane-contained, liquid desiccant for dehumidification

    Science.gov (United States)

    Kozubal, Eric Joseph

    2016-12-13

    An indirect evaporative cooler for cooling inlet supply air from a first temperature to a second, lower temperature using a stream of liquid coolant and a stream of exhaust or purge air. The cooler includes a first flow channel for inlet supply air and a second flow channel adjacent the first for exhaust air. The first and second flow channels are defined in part by sheets of a membrane permeable to water vapor such that mass is transferred as a vapor through the membrane from the inlet supply air to a contained liquid desiccant for dehumidification and also to the exhaust air as heat is transferred from the inlet supply air to the liquid coolant. A separation wall divides the liquid desiccant and the coolant but allows heat to be transferred from the supply air to the coolant which releases water vapor to the counter or cross flowing exhaust air.

  2. Novel Protic Ionic Liquid Composite Membranes with Fast and Selective Gas Transport Nanochannels for Ethylene/Ethane Separation.

    Science.gov (United States)

    Dou, Haozhen; Jiang, Bin; Xiao, Xiaoming; Xu, Mi; Tantai, Xiaowei; Wang, Baoyu; Sun, Yongli; Zhang, Luhong

    2018-04-25

    Protic ionic liquids (PILs) were utilized for the fabrication of composite membranes containing silver salt as the C 2 H 4 transport carrier to perform C 2 H 4 /C 2 H 6 separation for the first time. The intrinsic nanostructures of PILs were adopted to construct fast and selective C 2 H 4 transport nanochannels. The investigation of structure-performance relationships of composite membranes suggested that transport nanochannels (polar domains of PILs) could be tuned by the sizes of cations, which greatly manipulated activity of the carrier and determined the separation performances of membranes. The role of different carriers in the facilitated transport was studied, which revealed that the PILs were good solvents for dissolution and activation of the carrier due to their hydrogen bond networks and waterlike properties. The operating conditions of separation process were investigated systemically and optimized, confirming C 2 H 4 /C 2 H 6 selectivity was enhanced with the increase of silver salt concentration, the flow rate of sweep gas, and the feed ratio of C 2 H 4 to C 2 H 6 , as well as the decrease of the transmembrane pressure and operating temperature. Furthermore, the composite membranes exhibited long-term stability and obtained very competitive separation performances compared with other results. In summary, PIL composite membranes, which possess good long-term stability, high C 2 H 4 /C 2 H 6 selectivity, and excellent C 2 H 4 permeability, may have a good perspective in industrial C 2 H 4 /C 2 H 6 separation.

  3. Liquid membrane extraction techniques for trace metal analysis and speciation in environmental and biological matrices

    Energy Technology Data Exchange (ETDEWEB)

    Ndungu, Kuria

    1999-04-01

    In this thesis, liquid-membrane-based methods for the analysis of trace metal species in samples of environmental and biological origin were developed. By incorporating extracting reagents in the membrane liquid, trace metal ions were selectively separated from humic-rich natural waters and urine samples, prior to their determination using various instrumental techniques. The extractions were performed in closed flow systems thus allowing easy automation of both the sample clean-up and enrichment. An acidic organophosphorus reagent (DEHPA) and a basic tetraalkylammonium reagent (Aliquat-336) were used as extractants in the membrane liquid to selectively extract and enrich cationic and anionic metal species respectively. A speciation method for chromium species was developed that allowed the determination of cationic Cr(III) species and anionic CR(VI) species in natural water samples without the need of a chromatographic separation step prior to their detection. SLM was also coupled on-line to potentiometric stripping analysis providing a fast and sensitive method for analysis of Pb in urine samples. A microporous membrane liquid-liquid extraction (MMLLE) method was developed for the determination of organotin compounds in natural waters that reduced the number of manual steps involved in the LLE of organotin compounds prior to their CC separation. Clean extracts obtained after running unfiltered humic-rich river water samples through the MMLLE flow system allowed selective determination of all the organotin compounds in a single run using GC-MS in the selected ion monitoring mode (SIM) 171 refs, 9 figs, 4 tabs

  4. Manipulating lipid membrane architecture by liquid crystal-analog curvature elasticity (Presentation Recording)

    Science.gov (United States)

    Lee, Sin-Doo

    2015-10-01

    Soft matters such as liquid crystals and biological molecules exhibit a variety of interesting physical phenomena as well as new applications. Recently, in mimicking biological systems that have the ability to sense, regulate, grow, react, and regenerate in a highly responsive and self-adaptive manner, the significance of the liquid crystal order in living organisms, for example, a biological membrane possessing the lamellar order, is widely recognized from the viewpoints of physics and chemistry of interfaces and membrane biophysics. Lipid bilayers, resembling cell membranes, provide primary functions for the transport of biological components of ions and molecules in various cellular activities, including vesicle budding and membrane fusion, through lateral organization of the membrane components such as proteins. In this lecture, I will describe how the liquid crystal-analog curvature elasticity of a lipid bilayer plays a critical role in developing a new platform for understanding diverse biological functions at a cellular level. The key concept is to manipulate the local curvature at an interface between a solid substrate and a model membrane. Two representative examples will be demonstrated: one of them is the topographic control of lipid rafts in a combinatorial array where the ligand-receptor binding event occurs and the other concerns the reconstitution of a ring-type lipid raft in bud-mimicking architecture within the framework of the curvature elasticity.

  5. Conductivity Scaling Relationships in Nanostructured Membranes based on Protic Polymerized Ionic Liquids

    Science.gov (United States)

    Sanoja, Gabriel; Lynd, Nathaniel; Segalman, Rachel

    2015-03-01

    Nanostructured membranes based on protic polymerized ionic liquids are of great interest for a variety of electrochemical applications. Understanding the relationship between composition, structure, and ionic conductivity for these materials is essential for designing novel membranes with improved properties. In this work, we explore the effect of volume fraction of ionic liquid on conductivity, σ using a model system composed of poly[isoprene-block-(ethylene oxide-stat-histamine glycidyl ether) diblock copolymers [PI- b - P(EO-stat-HGE)] and the resulting [PI- b - P(EO-stat-IL)] obtained after treatment with trifluoroacetic acid. These materials self-assemble into lamellar structures with volume fractions of ionic liquid ranging from 0.50 to 0.90 as demonstrated by SAXS. PI- b - P(EO-stat-IL) membranes exhibit conductivities up to 4 x 10-3 S/cm at room temperature. In addition, PI- b - P(EO-stat-IL) based membranes have lower water uptake (λ = 8-10) in comparison with most proton conducting membranes reported elsewhere. The low λ in these membranes might translate into a stronger effect of morphology on transport properties. Joint Center for Artificial Photosynthesis.

  6. Liquid-Feed Methanol Fuel Cell With Membrane Electrolyte

    Science.gov (United States)

    Surampudi, Subbarao; Narayanan, S. R.; Halpert, Gerald; Frank, Harvey; Vamos, Eugene

    1995-01-01

    Fuel cell generates electricity from direct liquid feed stream of methanol/water solution circulated in contact with anode, plus direct gaseous feed stream of air or oxygen in contact with cathode. Advantages include relative simplicity and elimination of corrosive electrolytic solutions. Offers potential for reductions in size, weight, and complexity, and for increases in safety of fuel-cell systems.

  7. Effective Purification of Biogas by Condensing-Liquid Membrane

    Czech Academy of Sciences Publication Activity Database

    Poloncarzová, Magda; Vejražka, Jiří; Veselý, Václav; Izák, Pavel

    2010-01-01

    Roč. 50, č. 3 (2010), s. 669-671 ISSN 1433-7851 R&D Projects: GA MPO FR-TI1/245 Institutional research plan: CEZ:AV0Z40720504 Keywords : biogas purification * condensing liquid * gas permeation Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 12.730, year: 2010

  8. How Ionic Liquid Changes Properties of Dense Polydimethylsiloxane Membrane?

    Czech Academy of Sciences Publication Activity Database

    Kohoutová, Marie; Sikora, Antonín; Hovorka, Š.; Randová, A.; Schauer, Jan; Poloncarzová, Magda; Izák, Pavel

    2010-01-01

    Roč. 14, 1-3 (2010), s. 78-82 ISSN 1944-3994 R&D Projects: GA ČR GA203/08/0465 Institutional research plan: CEZ:AV0Z40720504; CEZ:AV0Z40500505 Keywords : pervaporation * ionic liquid * fermentation Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 0.752, year: 2010

  9. H-Bond stabilized columnar discotic liquid crystals

    NARCIS (Netherlands)

    Paraschiv, I.

    2007-01-01

    Since 1977, more than 2300 publications on discotic (disk-like) liquid crystalline materials have appeared. Discotic liquid crystals, which usually consist of polyaromatic molecules surrounded by long peripheral alkyl tails, can form liquid crystalline mesophases in a wide temperature range. Within

  10. Stabilization of axisymmetric liquid bridges through vibration-induced pressure fields.

    Science.gov (United States)

    Haynes, M; Vega, E J; Herrada, M A; Benilov, E S; Montanero, J M

    2018-03-01

    Previous theoretical studies have indicated that liquid bridges close to the Plateau-Rayleigh instability limit can be stabilized when the upper supporting disk vibrates at a very high frequency and with a very small amplitude. The major effect of the vibration-induced pressure field is to straighten the liquid bridge free surface to compensate for the deformation caused by gravity. As a consequence, the apparent Bond number decreases and the maximum liquid bridge length increases. In this paper, we show experimentally that this procedure can be used to stabilize millimeter liquid bridges in air under normal gravity conditions. The breakup of vibrated liquid bridges is examined experimentally and compared with that produced in absence of vibration. In addition, we analyze numerically the dynamics of axisymmetric liquid bridges far from the Plateau-Rayleigh instability limit by solving the Navier-Stokes equations. We calculate the eigenfrequencies characterizing the linear oscillation modes of vibrated liquid bridges, and determine their stability limits. The breakup process of a vibrated liquid bridge at that stability limit is simulated too. We find qualitative agreement between the numerical predictions for both the stability limits and the breakup process and their experimental counterparts. Finally, we show the applicability of our technique to control the amount of liquid transferred between two solid surfaces. Copyright © 2017 Elsevier Inc. All rights reserved.

  11. Uranyl ion transport across tri-n-butyl phosphate/n-dodecane liquid membranes

    International Nuclear Information System (INIS)

    Shukla, J.P.; Misra, S.K.

    1991-01-01

    Carrier-facilitated transport of uranium (VI) against its concentration gradient from aqueous nitrate acidic solutions across organic bulk liquid membranes (BLM) and supported liquid membranes (SLM) containing TBP as the mobile carrier and n-dodecane as the membrane solvent was investigated. Extremely dilute uranyl nitrate solutions in about 2.5 M nitric acid generally constituted as the source phase. Uranyl transport appreciably increased with both stirring of the receiving phase and the carrier concentration in the organic membrane, while enhanced acidity of the strip side adversely affected the partioning of the cation into this phase. Among the several reagents tested, diluted ammonium carbonate (∼1M) solutions served efficiently as the stripant. Besides Accurel polypropylene (PP) film as the solid support for SLM, some silicon flat-sheet membranes with different inorganic fillers like silica, calcium silicate, calcium carbonate, chromium oxide, zinc oxide etc. and teflon membranes transported about 70% of uranium in nearly 7-8 hr employing 1 M ammonium carbonate as the strippant. Specifically, 30% TBP supported on Accurel flat-sheet supports transfered better than 70% of uranium from moderate acid feeds (2.5M) under similar conditions. Membranes supporting Aliquat-336, TLA, TOPO etc. yielded somewhat poor uranium recoveries. The feed : strip volume ratio showed an inverse relationship to the fraction of cation transported. (author). 9 refs., 2 tab s

  12. Synthesis of polymer membranes of different porosity and their application for phenol removal from liquid phase

    International Nuclear Information System (INIS)

    Hofman-Bieniek, Magdalena; Jasiewicz, Katarzyna; Pietrzak, Robert

    2014-01-01

    Preparation of polymeric membranes based on polyethersulfone (PES) modified by adding different amounts of a pore-forming agent (PVP) is presented, and potential application of the membranes obtained for removal of phenol from the liquid phase is examined. The addition of various amounts of PVP has been shown to bring about changes in the content of the surface oxygen groups, but has no significant effect on the chemical character of the groups and acidic groups dominate. Filtration by phenol solution leads to significant changes in the total content of surface oxides; however, the acidic groups remain dominant. Membranes characterized by higher porosity exhibited more stable and higher rejection ratio for phenol removal. Although all the membranes were characterized by similar rejection ratios for phenol removal, the cake resistance (Rc) and pore resistance (Rp) values were found to depend significantly on the structure and porosity of the membrane applied for filtration

  13. Determination of bromoxynil and ioxynil in the presence of carbamates by supported liquid membrane-liquid chromatography in river waters

    Directory of Open Access Journals (Sweden)

    Titus Motswadi Maswabi

    2003-12-01

    Full Text Available Sample pre-treatment and enrichment using the supported liquid membrane (SLM technique for the determination of phenolic nitrile herbicides in presence of carbamates in river water samples was investigated. The uncharged herbicide molecules from the flowing aqueous solution diffuse through an immobilized water-immiscible organic solvent, supported by a porous polytetrafluoroethylene (PTFE membrane, and trapped in a stagnant acidic acceptor phase in an ionic form. Using n-undecane as a membrane solvent, the SLM extraction methodology was successfully used for the enrichment and separation of phenolic nitrile herbicides in environmental waters with extraction efficiencies of 60% or better. A RDS (% of 2.1 and 1.8 was obtained for the extraction of ioxynil and bromoxynil from river water, respectively.

  14. Low-voltage electrochemically stimulated stir membrane liquid-liquid microextraction as a novel technique for the determination of methadone.

    Science.gov (United States)

    Ara, Katayoun Mahdavi; Raofie, Farhad

    2017-06-01

    In the present work, for the first time, a new portable setup was designed, developed and presented for the extraction of methadone, as a basic drug model from biological fluid samples using a low-voltage electrically stimulated stir membrane liquid-liquid microextraction technique (LV-ESSM-LLME), followed by high-performance liquid chromatography with ultraviolet detection. This new approach combines the advantages of stir membrane liquid-liquid microextraction and electrokinetic migration in the same unit under soft electrochemical conditions in a portable device, allowing for the isolation and preconcentration of the target analyte in a simple and efficient manner under three-phase mode. To investigate the influence of external stirring and the application of electrical potential as the driving force, a comparative study of all variables involved in the extraction process was carried out using the low-voltage electromembrane extraction (LV-EME) and LV-ESSM-LLME methods. Under soft electrokinetic migration conditions, methadone was transported from an acidic sample solution (pH 4.0), through the NPOE immobilized in the pores of the porous polypropylene sheet membrane, and into 25µL of 10mmolL -1 HCl acceptor solution with a stirring rate of 1000rpm and 700rpm after 15min and 20min for LV-ESSM-LLME and LV-EME, respectively. Under the optimized conditions, preconcentration factors in the range of 17-24 and 21.5-29 for LV-EME and LV-ESSM-LLME, respectively, were considered, and satisfactory repeatability (4.5<[RSD]<7.5) was obtained in different matrices. The obtained relative recoveries of the target analyte were in the range of 87-94% and 93-101% for LV-EME and LV-ESSM-LLME, respectively, which indicated the excellent capability of the developed methods to extract methadone from complex matrices. Copyright © 2017 Elsevier B.V. All rights reserved.

  15. Stabilizing liquid drops of arbitrary shape by the interfacial jamming of nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Russell, Thomas P.; Cui, Mengmeng; Emrick, Todd

    2018-01-30

    A stabilized assembly including a first liquid phase of non-spherical droplets in a second liquid phase, wherein the second liquid phase is immiscible with the first phase, and nanoparticle surfactants assembled at an interface of the non-spherical droplets and the second phase is disclosed. The nanoparticle surfactants include nanoparticles and end-functionalized polymers that can interact through ligand type interactions, and the first phase is stabilized by a disordered, jammed layer of nanoparticle surfactants. A method of preparing a stabilized assembly is also disclosed.

  16. Swelling of Polymeric Membranes in Room Temperature Ionic Liquids

    Czech Academy of Sciences Publication Activity Database

    Izák, Pavel; Hovorka, Š.; Bartovský, T.; Bartovská, L.; Crespo, J.G.

    2007-01-01

    Roč. 296, 1-2 (2007), s. 131-138 ISSN 0376-7388 Grant - others:FCT(PT) SFRH/BPD/9470/2002; FCT(PT) POCTI/EQU/35437/2000 Institutional research plan: CEZ:AV0Z40720504 Source of funding: R - rámcový projekt EK ; R - rámcový projekt EK Keywords : membrane swelling * swelling measurement * anisotropic swelling Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 2.432, year: 2007

  17. Carrier mediated transport through supported liquid membranes; determination of transport parameters from a single transport experiment

    NARCIS (Netherlands)

    Chrisstoffels, L.A.J.; Struijk, Wilhelmina; de Jong, Feike; Reinhoudt, David

    1996-01-01

    This paper describes a time-dependent transport model for carrier assisted cation transport through supported liquid membranes. The model describes the flux of salt as a function of time and two parameters viz. the diffusion coefficient of the cation complex (D), and the extraction constant (Kex).

  18. Parallel artificial liquid membrane extraction of acidic drugs from human plasma

    DEFF Research Database (Denmark)

    Roldan-Pijuan, Mercedes; Pedersen-Bjergaard, Stig; Gjelstad, Astrid

    2015-01-01

    The new sample preparation concept “Parallel artificial liquid membrane extraction (PALME)” was evaluated for extraction of the acidic drugs ketoprofen, fenoprofen, diclofenac, flurbiprofen, ibuprofen, and gemfibrozil from human plasma samples. Plasma samples (250 μL) were loaded into individual...

  19. Micro-electromembrane extraction across free liquid membranes. Instrumentation and basic principles

    Czech Academy of Sciences Publication Activity Database

    Kubáň, Pavel; Boček, Petr

    2014-01-01

    Roč. 1346, Jun (2014), s. 25-33 ISSN 0021-9673 R&D Projects: GA ČR(CZ) GA13-05762S Institutional support: RVO:68081715 Keywords : free liquid membranes * micro-electromembrane extraction * sample pretreatment Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 4.169, year: 2014

  20. Direct coupling of supported liquid membranes to capillary electrophoresis for analysis of complex samples: A tutorial

    Czech Academy of Sciences Publication Activity Database

    Kubáň, Pavel; Boček, Petr

    2013-01-01

    Roč. 787, JUL (2013), s. 10-23 ISSN 0003-2670 R&D Projects: GA ČR(CZ) GA13-05762S Institutional support: RVO:68081715 Keywords : capillary electrophoresis * supported liquid membranes * direct coupling Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 4.517, year: 2013

  1. Effect of storage duration on the rheological properties of goose liquid egg products and eggshell membranes

    Czech Academy of Sciences Publication Activity Database

    Kumbár, V.; Nedomová, Š.; Trnka, Jan; Buchar, J.; Pytel, R.

    2016-01-01

    Roč. 95, č. 7 (2016), s. 1693-1701 ISSN 0032-5791 Institutional support: RVO:61388998 Keywords : egg yolk * albumen * liquid whole egg * rheology * eggshell membrane Subject RIV: BO - Biophysics Impact factor: 1.908, year: 2016 http://ps.oxfordjournals.org/

  2. Micro-electromembrane extraction across free liquid membranes. Extractions of basic drugs from undiluted biological samples

    Czech Academy of Sciences Publication Activity Database

    Kubáň, Pavel; Boček, Petr

    2014-01-01

    Roč. 1337, Apr (2014), s. 32-39 ISSN 0021-9673 R&D Projects: GA ČR(CZ) GA13-05762S Institutional support: RVO:68081715 Keywords : micro-electromembrane extraction * free liquid membranes * biological samples Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 4.169, year: 2014

  3. Micro-electromembrane extraction across free liquid membranes. Extractions of basic drugs from undiluted biological samples

    Czech Academy of Sciences Publication Activity Database

    Kubáň, Pavel; Boček, Petr

    2014-01-01

    Roč. 1337, Apr (2014), s. 32-39 ISSN 0021-9673 R&D Projects: GA ČR(CZ) GA13-05762S Institutional support: RVO:68081715 Keywords : micro-electromembrane extraction * free liquid membranes * biological samples Subject RIV: CB - Analytical Chemistry , Separation Impact factor: 4.169, year: 2014

  4. Transfer of heparin polyion across a polarized water/ionic liquid membrane interface

    Czech Academy of Sciences Publication Activity Database

    Langmaier, Jan; Samec, Zdeněk; Samcová, E.; Tůma, P.

    2012-01-01

    Roč. 24, OCT 2012 (2012), s. 25-27 ISSN 1388-2481 R&D Projects: GA ČR GAP206/11/0707 Institutional support: RVO:61388955 Keywords : heparin polyion * ionic liquid membrane * amperometric detection Subject RIV: CG - Electrochemistry Impact factor: 4.425, year: 2012

  5. Study on treatment of industrial wastewater with thorium by the liquid membrane emulsion technology

    International Nuclear Information System (INIS)

    Che Liping; Yu Yongfu; Yuan Jizu

    2005-01-01

    The enrichment of thorium from industrial wastewater with Th 4+ is studied by the liquid membrane emulsion technology of CCl 4 -N205-P204+TBP-HNO 3 . The conditions of making emulsion and the technological factors such as the ratios of oil to inner and water to emulsion, the pH and the extraction time are investigated. (authors)

  6. Solute Transport from Aqueous Mixture through Supported Ionic Liquid Membrane by Pervaporation.

    Czech Academy of Sciences Publication Activity Database

    Izák, Pavel; Koekerling, M.; Kragl, U.

    2006-01-01

    Roč. 199, 1-3 (2006) , s. 96–98 ISSN 0011-9164. [Euromembrane 2006. Giardini, Naxos, 24.09.2006-28.09.2006] Institutional research plan: CEZ:AV0Z40720504 Keywords : supported ionic liquid membrane * pervaporation * 1,3-propanediol Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 0.917, year: 2006

  7. How do polymerized room-temperature ionic liquid membranes plasticize during high pressure CO2 permeation?

    NARCIS (Netherlands)

    Simons-Fischbein, K.; Nijmeijer, Dorothea C.; Bara, J.B.; Noble, R.D.; Wessling, Matthias

    2010-01-01

    Room-temperature ionic liquids (RTILs) are a class of organic solvents that have been explored as novel media for CO2 separations. Polymerized RTILs (poly(RTILs)) can be synthesized from RTIL monomers to form dense, solid gas selective membranes. It is of interest to understand the permeation

  8. Selectivity of NF membrane for treatment of liquid waste containing uranium

    International Nuclear Information System (INIS)

    Oliveira, Elizabeth E.M.; Barbosa, Celina C.R.; Afonso, Julio C.

    2013-01-01

    The performance of two nanofiltration membranes were investigated for treatment of liquid waste containing uranium through two conditions permeation: permeation test and concentration test of the waste. In the permeation test solution permeated returned to the feed tank after collected samples each 3 hours. In the test of concentration the permeated was collected continuously until 90% reduction of the feed volume. The liquid waste ('carbonated water') was obtained during conversion of UF 6 to UO 2 in the cycle of nuclear fuel. This waste contains uranium concentration on average 7.0 mg L -1 , and not be eliminated to the environmental. The waste was permeated using a cross-flow membrane cell in the pressure of the 1.5 MPa. The selectivity of the membranes for separation of uranium was between 83% and 90% for both tests. In the concentration tests the waste was concentrated around for 5 times. The surface layer of the membranes was evaluated before and after the tests by infrared spectroscopy (ATR-FTIR), field emission microscopy (FESEM) and atomic force spectroscopy (AFM). The membrane separation process is a technique feasible to and very satisfactory for treatment the liquid waste. (author)

  9. Polyethersulfone flat sheet and hollow fiber membranes from solutions in ionic liquids

    KAUST Repository

    Kim, Dooli

    2017-06-10

    We fabricated flat-sheet and hollow fiber membranes from polyethersulfone (PES) solutions in two ionic liquids: 1-ethyl-3-methylimidazolium diethyl phosphate ([EMIM]DEP) and 1,3-dimethylimidazolium dimethyl phosphate ([MMIM]DMP). The solvents are non-volatile and less toxic than organic solvents, such as dimethylformamide (DMF). The membranes morphologies were compared with those of membranes prepared from solutions in DMF, using electron microscopy. Water permeance, solute rejection and mechanical strengths were evaluated. Membranes were applied to DNA separation. While membranes based on PES were successfully prepared, polysulfone (PSf) does not dissolve in the same ionic liquids. The discrepancy between PES and PSf could not be explained using classical Flory-Huggins theory, which does not consider the coulombic contributions in ionic liquids. The differences in solubility could be understood, by applying density functional theory to estimate the interaction energy between the different polymers and solvents. The theoretical results were supported by experimental measurements of intrinsic viscosity and dynamic light scattering (DLS).

  10. The Acinar Cage: Basement Membranes Determine Molecule Exchange and Mechanical Stability of Human Breast Cell Acini.

    Directory of Open Access Journals (Sweden)

    Aljona Gaiko-Shcherbak

    Full Text Available The biophysical properties of the basement membrane that surrounds human breast glands are poorly understood, but are thought to be decisive for normal organ function and malignancy. Here, we characterize the breast gland basement membrane with a focus on molecule permeation and mechanical stability, both crucial for organ function. We used well-established and nature-mimicking MCF10A acini as 3D cell model for human breast glands, with ether low- or highly-developed basement membrane scaffolds. Semi-quantitative dextran tracer (3 to 40 kDa experiments allowed us to investigate the basement membrane scaffold as a molecule diffusion barrier in human breast acini in vitro. We demonstrated that molecule permeation correlated positively with macromolecule size and intriguingly also with basement membrane development state, revealing a pore size of at least 9 nm. Notably, an intact collagen IV mesh proved to be essential for this permeation function. Furthermore, we performed ultra-sensitive atomic force microscopy to quantify the response of native breast acini and of decellularized basement membrane shells against mechanical indentation. We found a clear correlation between increasing acinar force resistance and basement membrane formation stage. Most important native acini with highly-developed basement membranes as well as cell-free basement membrane shells could both withstand physiologically relevant loads (≤ 20 nN without loss of structural integrity. In contrast, low-developed basement membranes were significantly softer and more fragile. In conclusion, our study emphasizes the key role of the basement membrane as conductor of acinar molecule influx and mechanical stability of human breast glands, which are fundamental for normal organ function.

  11. Pemisahan Unsur Samarium dan Yttrium dari Mineral Tanah Jarang dengan Teknik Membran Cair Berpendukung (Supported Liquid Membrane

    Directory of Open Access Journals (Sweden)

    Amri Amin

    2009-06-01

    Full Text Available he increasing use of rare earth elements in high technology industries needs to be supported by developmental work for the separation of elements. The research objective is fiercely attracting and challenging considering the similarity of bath physical and chemical properties among these elements. The rate separation of samarium and yttrium elements using supported liquid membrane has been studied. Polytetrafluoroethylene (PTFE with pore size of 0.45 µm has been used as the membrane and di(2-ethylhexyl phosphate (D2EHP in hexane has been used as a carrier and nitric acid solution has been used as receiving phase. Result of experiments showed that the best separation rate of samarium and yttrium elements could be obtained at feeding phase of pH 3.0, di(2-ethylhexyl phosphate (D2EHP concentration of 0.3 M, agitation rate of 700 rpm, agitation time of 2 hours, and nitric acid and its solution concentrations of 1.0 M and 0.1 M, respectively. At this condition, separation rates of samarium and yttrium were 64.4 and 67.6%, respectively.   Keywords: liquid membrane, rare earth elements, samarium, yttrium

  12. Determination of membrane degradation products in the product water of polymer electrolyte membrane fuel cells using liquid chromatography mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Zedda, Marco

    2011-05-12

    The predominant long term failure of polymer electrolyte membranes (PEM) is caused by hydroxyl radicals generated during fuel cell operation. These radicals attack the polymer, leading to chain scission, unzipping and consequently to membrane decomposition products. The present work has investigated decomposition products of novel sulfonated aromatic hydrocarbon membranes on the basis of a product water analysis. Degradation products from the investigated membrane type and the possibility to detect these compounds in the product water for diagnostic purposes have not been discovered yet. This thesis demonstrates the potential of solid phase extraction and liquid chromatography tandem mass spectrometry (SPE-LC-MS/MS) for the extraction, separation, characterization, identification and quantification of membrane degradation products in the product water of fuel cells. For this purpose, several polar aromatic hydrocarbons with different functional groups were selected as model compounds for the development of reliable extraction, separation and detection methods. The results of this thesis have shown that mixed mode sorbent materials with both weak anion exchange and reversed phase retention properties are well suited for reproducible extraction of both molecules and ions from the product water. The chromatographic separation of various polar aromatic hydrocarbons was achieved by means of phase optimized liquid chromatography using a solvent gradient and on a C18 stationary phase. Sensitive and selective detection of model compounds could be successfully demonstrated by the analysis of the product water using tandem mass spectrometry. The application of a hybrid mass spectrometer (Q Trap) for the characterization of unknown polar aromatic hydrocarbons has led to the identification and confirmation of 4-hydroxybenzoic acid in the product water. In addition, 4-HBA could be verified as a degradation product resulting from PEM decomposition by hydroxyl radicals using an

  13. The Colloidal Stability of Magnetic Nanoparticles in Ionic Liquids

    Science.gov (United States)

    2015-08-03

    Ionic Liquids 5a. CONTRACT NUMBER FA2386-14-1-4062 5b. GRANT NUMBER Grant 14IOA088 AOARD-144062 5c. PROGRAM ELEMENT NUMBER 61102F 6...NOTES 14. ABSTRACT During the reporting period the development of the ionic liquid ferrofluid (ILFF) based on EMIM-NTf2 was continued. The...ferrofluids based on other high-boiling solvents. 15. SUBJECT TERMS Electric Propulsion, Ionic liquids 16. SECURITY CLASSIFICATION

  14. Cross-linked comb-shaped anion exchange membranes with high base stability

    Energy Technology Data Exchange (ETDEWEB)

    Li, NW; Wang, LZ; Hickner, M

    2014-01-01

    A unique one-step cross-linking strategy that connects quaternary ammonium centers using Grubbs II-catalyzed olefin metathesis was developed. The cross-linked anion exchange membranes showed swelling ratios of less than 10% and hydroxide conductivities of 18 to 40 mS cm(- 1). Cross-linking improved the membranes' stability to hydroxide degradation compared to their non-cross-linked analogues.

  15. The spectrin-based membrane skeleton stabilizes mouse megakaryocyte membrane systems and is essential for proplatelet and platelet formation

    Science.gov (United States)

    Patel-Hett, Sunita; Wang, Hongbei; Begonja, Antonija J.; Thon, Jonathan N.; Alden, Eva C.; Wandersee, Nancy J.; An, Xiuli; Mohandas, Narla; Hartwig, John H.

    2011-01-01

    Megakaryocytes generate platelets by remodeling their cytoplasm first into proplatelets and then into preplatelets, which undergo fission to generate platelets. Although the functions of microtubules and actin during platelet biogenesis have been defined, the role of the spectrin cytoskeleton is unknown. We investigated the function of the spectrin-based membrane skeleton in proplatelet and platelet production in murine megakaryocytes. Electron microscopy revealed that, like circulating platelets, proplatelets have a dense membrane skeleton, the main fibrous component of which is spectrin. Unlike other cells, megakaryocytes and their progeny express both erythroid and nonerythroid spectrins. Assembly of spectrin into tetramers is required for invaginated membrane system maturation and proplatelet extension, because expression of a spectrin tetramer–disrupting construct in megakaryocytes inhibits both processes. Incorporation of this spectrin-disrupting fragment into a novel permeabilized proplatelet system rapidly destabilizes proplatelets, causing blebbing and swelling. Spectrin tetramers also stabilize the “barbell shapes” of the penultimate stage in platelet production, because addition of the tetramer-disrupting construct converts these barbell shapes to spheres, demonstrating that membrane skeletal continuity maintains the elongated, pre-fission shape. The results of this study provide evidence for a role for spectrin in different steps of megakaryocyte development through its participation in the formation of invaginated membranes and in the maintenance of proplatelet structure. PMID:21566095

  16. Enhancement of membrane stability on magnetic responsive hydrogel microcapsules for potential on-demand cell separation.

    Science.gov (United States)

    Wen, Huiyun; Gao, Ting; Fu, Zizhen; Liu, Xing; Xu, Jiatong; He, Yishu; Xu, Ningxia; Jiao, Ping; Fan, An; Huang, Saipeng; Xue, Weiming

    2017-02-10

    It is of high interest to obtain hydrogel membranes with optimum mechanical stability, which is a prerequisite to the successful fabrication of hydrogel microcapsules for cell separation. In this work, we developed magnetic responsive alginate/chitosan (MAC) hydrogel microcapsules by co-encapsulation of microbial cells and superparamagnetic iron oxide nanoparticles (SPIONs) reacting under a high voltage electrostatic field. We investigated the influence of the molecular weight of chitosan, microcapsules size, and membrane crosslinking time on the swelling behavior of microcapsules as an indicator of stability of the membranes. The results demonstrated that the suitable membrane stability conditions were obtained by a crosslinking of the microspheres with a chitosan presenting a molecular weight of 70kDa for 15-30min resulting in a membrane thickness of approximately 30mm. Considering the need of maintaining the cells inside the microcapsules, fermentation at 37°C and at neutral pH was favorable. Moreover, the MAC microcapsules sizing between 300 and 380μm were suitable for immobilizing Bacillus licheniformis in a 286h multiple fed-bath operation with no leakage of the SPIONs and cells. Overall, the results of this study provided strategies for the rational design of magnetic microcapsules exhibiting suitable mechanical stable membranes. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. Foam-film-stabilized liquid bridge networks in evaporative lithography and wet granular matter

    KAUST Repository

    Vakarelski, Ivan Uriev

    2013-04-23

    Evaporative lithography using latex particle templates is a novel approach for the self-assembly of suspension-dispersed nanoparticles into ordered microwire networks. The phenomenon that drives the self-assembly process is the propagation of a network of interconnected liquid bridges between the template particles and the underlying substrate. With the aid of video microscopy, we demonstrate that these liquid bridges are in fact the border zone between the underlying substrate and foam films vertical to the substrate, which are formed during the evaporation of the liquid from the suspension. The stability of the foam films and thus the liquid bridge network stability are due to the presence of a small amount of surfactant in the evaporating solution. We show that the same type of foam-film-stabilized liquid bridge network can also propagate in 3D clusters of spherical particles, which has important implications for the understanding of wet granular matter. © 2013 American Chemical Society.

  18. Broadband Liquid Dampers to Stabilize Flexible Spacecraft Structures

    NARCIS (Netherlands)

    Kuiper, J.M.

    2012-01-01

    Mass-spring and liquid dampers enable structural vibration control to attenuate single, coupled lateral and torsional vibrations in diverse structures. Out of these, the passively tuned liquid damper (TLD) class is wanted due to its broad applicability, extreme reliability, robustness, long life

  19. Membrane bioreactor with a porous hydrophobic membrane as a gas-liquid contactor for waste gas treatment.

    Science.gov (United States)

    Reij, M W; de Bont, J A; Hartmans, S; de Gooijer, K D

    1995-01-20

    A novel type of bioreactor for waste gas treatment has been designed. The reactor contains a microporous hydrophobic membrane to create a large interface between the waste gas and the aqueous phase. To test the new reactor, propene was chosen because of its high air/water partition coefficient, which causes a low water concentration and hampers its removal from air. Propene transfer from air to a suspension of propene-utilizing Xanthobacter Py2 cells in the membrane bioreactor proved to be controlled by mass transfer in the liquid phase. The resistance of the membrane was negligible. Simulated propene transfer rates agreed well with the experimental data. A stable biofilm of Xanthobacter Py2 developed on the membrane during prolonged operation. The propene flux into the biofilm was 1 x 10(-6) mol m(-2) s(-1) at a propene concentration of 9.3 x 10(-2) mol m(-3) in the gas phase. (c) 1995 John Wiley & Sons, Inc.

  20. Liquid dosage forms extemporaneously prepared from commercially available products - considering new evidence on stability.

    Science.gov (United States)

    Haywood, Alison; Glass, Beverley D

    2013-01-01

    Although the world's population is ageing and as a result of this an increasing number of patients are experiencing difficulty in swallowing, there remains a lack of commercially available oral liquids for both these older and paediatric patients. This presents a problem to health care professionals, especially the pharmacist in practice, who is often required to provide a solution for these patients by preparing oral liquids extemporaneously from commercially available products. Preparation of these oral liquids is challenging, both due to the lack of pharmacopoeial and stability-indicating formulae and the fact that their stability is not only determined by the active pharmaceutical ingredient, but also the ability of excipients from the commercial product to interact with each other and the active pharmaceutical ingredient. This increases the complexity of the stability considerations to be taken into account within these oral liquids, highlighting the number of parameters to be considered in the extemporaneous preparation of oral liquids. This paper presents new evidence on the stability of 42 oral liquids prepared from commercially available products, reported on in the literature since the previous review published in 2006. However, unlike the previous review where the stability concerns in 7.2% of the extemporaneously prepared oral liquids were mainly due to interaction between the active pharmaceutical ingredients and the excipients in the commercial product, most of these stability considerations have been recognised and this has resulted in the authors proposing solutions to these problems prior to the extemporaneous preparation of the oral liquid. As such this paper also focuses on the increased level of research that has been undertaken to solve previous issues related to stability, especially in terms of the use of commercial products, which is common practice in the extemporaneous preparation of oral liquids.

  1. Copper recovery in a bench-scale carrier facilitated tubular supported liquid membrane system

    Directory of Open Access Journals (Sweden)

    Makaka S.

    2010-01-01

    Full Text Available The extraction of copper ions in a tubular supported liquid membrane using LIX 984NC as a mobile carrier was studied, evaluating the effect of the feed characteristics (flowrate, density, viscosity on the feedside laminar layer of the membrane. A vertical countercurrent, double pipe perspex benchscale reactor consisting of a single hydrophobic PVDF tubular membrane mounted inside was used in all test work. The membrane was impregnated with LIX 984NC and became the support for this organic transport medium. Dilute Copper solution passed through the centre pipe and sulphuric acid as strippant passed through the shell side. Copper was successfully transported from the feedside to the stripside and from the data obtained, a relationship between Schmidt, Reynolds and Sherwood number was achieved of.

  2. The extraction of uranium from wet process phosphoric acid using a liquid surfactant membrane system

    International Nuclear Information System (INIS)

    Dickens, N.; Davies, G.A.

    1984-01-01

    A liquid membrane extraction process is examined for the extraction of uranium from wet process phosphoric acid. Uranium is present in the acid in concentrations up to 100 ppm which in principle makes it ideal for treatment with a membrane process. The membrane system studied is based on extraction using DEHPA-TOPO reagents which are contained within the organic phase of a water in oil emulsion. Formulations of the emulsion membrane system have been studied, the limitations of acid temperature, P 2 O 5 concentration and solid dispersed impurities in the acid have been studied in laboratory batch experiments and in a continuous pilot plant unit capable of treating 5l of concentrated acid per minute. Data from the pilot plant work has been used to develop a flowsheet for a commercial unit based on this process. (author)

  3. Synthesis of magnetic nanoparticles as a draw solute in forward osmosis membrane process for the treatment of radioactive liquid waste

    International Nuclear Information System (INIS)

    Yang, Heeman; Lee, Kune Woo; Moon, Jei Kwon

    2013-01-01

    These wastes contain about 0.3 ∼ 0.8 wt% of boric acid. It is known that reverse osmosis (RO) membrane can eliminate boron at high pH and boron of 40 ∼ 90% can be removed by RO membrane in pH condition. RO uses hydraulic pressure to oppose, and exceed, the osmotic pressure of an aqueous feed solution containing boric acid. As an emerging technology forward osmosis (FO) has attracted growing interest in wastewater treatment and desalination because FO operates at low or no hydraulic pressures. FO is a membrane process in which water flows across a semi-permeable membrane from a feed solution of lower osmotic pressure to a draw solution of higher osmotic pressure. However, the challenges of FO still lie in the fabrication of eligible FO membranes and the readily separable draw solutes of high osmotic pressures. Superparamagnetic Fe 3 O 4 nanoparticles can be separated from water by an external magnet field easily. If Fe 3 O 4 nanoparticles are coated with highly soluble organic substances, thus they can be used as a draw solute by concurrently generating high osmotic pressure and easy separation. The carboxylated polyglycerol coated Fe 3 O 4 nanoparticles have been successfully synthesized. The nanoparticles were about 50 nm in diameter and showed the good colloidal stability in aqueous solution. The osmolality and osmotic pressure were enough high to be used as a draw solute in FO. For the future work, we will investigate the performance of our magnetic draw solute in FO to remove boron in the simulated liquid waste

  4. The influence of different membrane components on the electrical stability of bilayer lipid membranes

    NARCIS (Netherlands)

    van Uitert, I.; le Gac, Severine; van den Berg, Albert

    A good understanding of cell membrane properties is crucial for better controlled and reproducible experiments, particularly for cell electroporation where the mechanism of pore formation is not fully elucidated. In this article we study the influence on that process of several constituents found in

  5. Effects of alpha-lipoic acids on sperm membrane integrity during liquid storage of boar semen

    Directory of Open Access Journals (Sweden)

    Laura Parlapan

    2015-05-01

    Full Text Available Preliminary studies have shown that sperm membrane from swine shows high sensitivity to cryopreservation process, causing a dramatic reduction in sperm quality. This has been attributed to the production of reactive oxygen species, that cause lipid peroxidation in sperm membranes. The aim of the present study was to minimize the oxidative attack by adding different concentration of alpha-lipoic acid into the sperm liquid storage at 17ºC for 7 days. Freshly ejaculated boar semen was diluted with Beltsville Thawing Solution (BTS and supplemented with 5 levels of alpha-lipoic  acid (0.015, 0.02, 0.05, 0.1, 0.15 mmol/ml. The membrane integrity was evaluated at days 0, 1, 3, 5 and 7 of liquid preservation, using flow cytometer FACSCanto II (BD Biociencias systems. The experiment indicate that supplementation of alpha-lipoic  acid to the semen liquid storage extender improve sperm membrane

  6. Interfacial Engineering of Supported Liquid Membranes by Vapor Cross-Linking for Enhanced Separation of Carbon Dioxide.

    Science.gov (United States)

    Kong, Li-Yun; Shan, Wei-Da; Han, Sheng-Li; Zhang, Tao; He, Lang-Chong; Huang, Kuan; Dai, Sheng

    2018-01-10

    Supported liquid membranes (SLMs) based on ionic liquids (ILs) with not only high gas permeability and selectivity, but also high stability under high pressure, are highly desired for gas separation applications. In this work, permeable and selective polyamide network (PN) layers are deposited on the surface of SLMs by utilizing the cross-linking reaction of trimesoyl chloride, which was pre-dispersed in the SLMs, and vapor of amine linkers. The vapor cross-linking method makes it easy to control the growth and aggregation of PN layers, owing to the significantly reduced reaction rate, and thereby ensuring the good distribution of PN layers on the surface of SLMs. With rational choice of amine linkers and optimization of vapor cross-linking conditions, the prepared sandwich-like PN@SLMs with ILs embedded homogeneously within polymeric matrices displayed much-improved CO 2 permeability and CO 2 /N 2 selectivity in relation to the pristine SLMs. Moreover, those SLMs with ILs impregnated into porous supports physically displayed improved stability under high pressure after vapor cross-linking, because the PN layers formed on the surface of SLMs help prevent the ILs from being squeezed out. This interfacial engineering strategy represents a significant advance in the surface modification of SLMs to endow them with promising applications in CO 2 capture. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. Synthesis and characterization of ionic liquid (EMImBF4)/Li+ - chitosan membranes for ion battery

    International Nuclear Information System (INIS)

    Pasaribu, Marvin H.; Arcana, I Made; Wahyuningrum, Deana

    2015-01-01

    Lithium ion battery has been currently developed and produced because it has a longer life time, high energycapacity, and the efficient use of lithium ion battery that is suitable for storing electrical energy. However, this battery has some drawbacks such as use liquid electrolytes that are prone to leakage and flammability during the battery charging process in high temperature. In this study, an ionic liquid 1-ethyl-3-methylimidazolium tetrafluoroborate (EMImBF4) containing Li + ions was synthesized and combined with chitosan polymer host as a polymer electrolyte membrane for lithium-ion batteries to solve this problems. This ionic liquid was obtained from the anion metathesis reaction between EMImBr and LiBF4 salt, while EMImBr was synthesized from the reaction between 1-methylimidazole and ethyl bromide utilizing Microwave Assisted Organic Synthesis (MAOS) method. The ionic liquid obtained was characterized by microstructure analysis with using NMR and FTIR spectroscopy. The polymer electrolyte membrane was characterized by analysis functional groups (FTIR), ionic conductivity (EIS), and surface morphology (SEM). The analysis results of ion conductivity by the EIS method showed the increase the ionic conductivity value of membranes from 1.30 × 10 −2 S cm −1 for chitosan to 1.30 × 10 −2 S cm −1 for chitosan with EMImBF4/Li + , and this result was supported by analysis the surface morphology (SEM)

  8. Broadband Liquid Dampers to Stabilize Flexible Spacecraft Structures

    OpenAIRE

    Kuiper, J.M.

    2012-01-01

    Mass-spring and liquid dampers enable structural vibration control to attenuate single, coupled lateral and torsional vibrations in diverse structures. Out of these, the passively tuned liquid damper (TLD) class is wanted due to its broad applicability, extreme reliability, robustness, long life time and ease of manufacturability. In this PhD thesis, the theory, design, verification and validation of multi-mode TLDs in terrestrial and mainly spacecraft (S/C) applications have been studied. Th...

  9. Stability of diphenylalanine peptide nanotubes under liquid conditions

    DEFF Research Database (Denmark)

    Andersen, Karsten Brandt; Castillo, Jaime; Hedstrom, Martin

    2011-01-01

    nanotubes are believed to be very stable both thermally and chemically. Previously, the chemical and thermal stability of self-organizing structures has been investigated after the evaporation of the solvent. However, it was recently discovered that the stability of the structures differed significantly...

  10. Nuclide separation modeling through reverse osmosis membranes in radioactive liquid waste

    Directory of Open Access Journals (Sweden)

    Byung-Sik Lee

    2015-12-01

    Full Text Available The aim of this work is to investigate the transport mechanism of radioactive nuclides through the reverse osmosis (RO membrane and to estimate its effectiveness for nuclide separation from radioactive liquid waste. An analytical model is developed to simulate the RO separation, and a series of experiments are set up to confirm its estimated separation behavior. The model is based on the extended Nernst–Plank equation, which handles the convective flux, diffusive flux, and electromigration flux under electroneutrality and zero electric current conditions. The distribution coefficient which arises due to ion interactions with the membrane material and the electric potential jump at the membrane interface are included as boundary conditions in solving the equation. A high Peclet approximation is adopted to simplify the calculation, but the effect of concentration polarization is included for a more accurate prediction of separation. Cobalt and cesium are specifically selected for the experiments in order to check the separation mechanism from liquid waste composed of various radioactive nuclides and nonradioactive substances, and the results are compared with the estimated cobalt and cesium rejections of the RO membrane using the model. Experimental and calculated results are shown to be in excellent agreement. The proposed model will be very useful for the prediction of separation behavior of various radioactive nuclides by the RO membrane.

  11. Influence of endothelium on the membrane-stabilizing effect of calcium

    African Journals Online (AJOL)

    These relaxation responses were attenuated in endothelium-denuded rings as well as following exposure to methylene blue. Conclusion: The results show that relaxation responses induced by high Ca2+ due to membrane stabilization is endothelium-dependent. Keywords: Calcium, rabbit aorta, Vascular smooth muscle, ...

  12. Enhanced thermal stability of the thylakoid membranes from spruce. A comparison with selected angiosperms

    Czech Academy of Sciences Publication Activity Database

    Karlický, Václav; Kurasová, Irena; Ptáčková, B.; Večeřová, Kristýna; Urban, Otmar; Špunda, Vladimír

    2016-01-01

    Roč. 130, 1-3 (2016), s. 357-371 ISSN 0166-8595 R&D Projects: GA MŠk(CZ) LO1415; GA ČR GA13-28093S Institutional support: RVO:67179843 Keywords : Norway spruce * Thermal stability * Circular dichroism * Photosystem II organization * Thylakoid membrane Subject RIV: ED - Physiology Impact factor: 3.864, year: 2016

  13. [Membrane-stabilizing preparations in the treatment of patients with heart rhythm disorders of different etiologies].

    Science.gov (United States)

    Vizir, A D; Grigor'eva, Z E; Stepanova, I V; Vizir, V A

    1991-10-01

    Data are reported of a study of the efficacy of membrane-stabilizing antiarrhythmic agents--ethmosin, ethacisin, allapinin. The latter was used in the treatment of 85 patients with arrhythmias of different etiology and proved more effective as compared with ethmosin and ethacisin. In ventricular extrasystole the effect was favourable in 86%, in supraventricular--in 70% of patients.

  14. Extraction of uranium(VI) by emulsion liquid membrane containing 5,8-diethyl-7-hydroxy-6-dodecanone oxime

    International Nuclear Information System (INIS)

    Akiba, Kenichi; Takahashi, Toshihiko; Kanno, Takuji

    1984-01-01

    Extraction of uranium(VI) by a liquid surfactant membrane has been studied. The stability of water-in-oil (w/o) emulsion dispersed in the continuous aqueous phase increased with an increase in surfactant concentrations and in the fraction of the organic phase in emulsion globules. Uranium(VI) in dilute acid solutions was extracted into (w/o) emulsions containing 5,8-diethyl-7-hydroxy-6-dodecanone oxime (LIX 63) as a mobile carrier and its concentration decreased according to [U]sub(t)=[U]sub(o)exp(-ksub(obsd)t). The apparent rate constants (ksub(obsd)) increased with an increase in carrier concentrations and in external pH values, while they were slightly dependent on the stripping acid concentrations. Uranium was transported and concentrated into the internal aqueous droplets. The final concentration of uranium in the external aqueous phase dropped to about 10 -3 of its initial value. (author)

  15. The stability of liquid-filled matrix ionization chamber electronic portal imaging devices for dosimetry purposes

    NARCIS (Netherlands)

    Louwe, R. J. W.; Tielenburg, R.; van Ingen, K. M.; Mijnheer, B. J.; van Herk, M. B.

    2004-01-01

    This study was performed to determine the stability of liquid-filled matrix ionization chamber (LiFi-type) electronic portal imaging devices (EPID) for dosimetric purposes. The short- and long-term stability of the response was investigated, as well as the importance of factors influencing the

  16. Removal of some ions from the radioactive liquid wastes by means of membrane techniques

    International Nuclear Information System (INIS)

    Roman, Gabriela; Garganciuc, Dana; Batrinescu, Gheorghe; Popescu, Georgeta

    2000-01-01

    The radioactive wastes imply important problems in the pollution control. Contrary to the case of other liquid wastes, which are specifically treated depending on the nature of pollutants, the liquid radioactive wastes are treated as a function of their activity (high, medium or low) and not depending on the nature of radioisotopes. The paper presents the advantages of the membrane processes as comparing with the classical processes in the removal of some ions from liquid radioactive waste up to values admissible of the current standards. Two types of radioactive liquid solutions were processed namely: one solution from the decontamination of the parts of an installation and other from the decontamination of primary circuit of the nuclear power plant. The first solution was treated with ultrafiltration and reverse osmosis, the retention for radioactive and toxic elements ranging between 14 - 69% for ultrafiltration and 63 - 99% for reverse osmosis. The second solution was processed only with reverse osmosis, a retention between 64 - 98% being obtained. The tests proved that by reverse osmosis membrane process a good removal efficiency of radioactive elements from liquid waste is obtained, corresponding to the requirements imposed by the current regulations. (author)

  17. Advanced Supported Liquid Membranes for Carbon Dioxide Control in Cabin Applications

    Science.gov (United States)

    Wickham, David T.; Gleason, Kevin J.; Engel, Jeffrey R.; Chullen, Cinda

    2016-01-01

    The development of new, robust, life support systems is critical to NASA's continued progress in space exploration. One vital function is maintaining the carbon dioxide (CO2) concentration in the cabin at levels that do not impair the health or performance of the crew. The carbon dioxide removal assembly (CDRA) is the current CO2 control technology on-board the International Space Station (ISS). Although the CDRA has met the needs of the ISS to date, the repeated cycling of the molecular sieve sorbent causes it to break down into small particles that clog filters or generate dust in the cabin. This reduces reliability and increases maintenance requirements. Another approach that has potential advantages over the current system is a membrane that separates CO2 from air. In this approach, cabin air contacts one side of the membrane while other side of the membrane is maintained at low pressure to create a driving force for CO2 transport across the membrane. In this application, the primary power requirement is for the pump that creates the low pressure and then pumps the CO2 to the oxygen recovery system. For such a membrane to be practical, it must have high CO2 permeation rate and excellent selectivity for CO2 over air. Unfortunately, conventional gas separation membranes do not have adequate CO2 permeability and selectivity to meet the needs of this application. However, the required performance could be obtained with a supported liquid membrane (SLM), which consists of a microporous material filled with a liquid that selectively reacts with CO2 over air. In a recently completed Phase II SBIR project, Reaction Systems, Inc. fabricated an SLM that is very close to meeting permeability and selectivity objectives for use in the Portable Life Support System (PLSS). This paper describes work carried out to evaluate its potential for use in the cabin.

  18. Functionalized copolyimide membranes for the separation of gaseous and liquid mixtures

    Directory of Open Access Journals (Sweden)

    Nadine Schmeling

    2010-08-01

    Full Text Available Functionalized copolyimides continue to attract much attention as membrane materials because they can fulfill the demands for industrial applications. Thus not only good separation characteristics but also high temperature stability and chemical resistance are required. Furthermore, it is very important that membrane materials are resistant to plasticization since it has been shown that this phenomenon leads to a significant increase in permeability with a dramatic loss in selectivity. Plasticization effects occur with most polymer membranes at high CO2 concentrations and pressures, respectively. Plasticization effects are also observed with higher hydrocarbons such as propylene, propane, aromatics or sulfur containing aromatics. Unfortunately, these components are present in mixtures of high commercial relevance and can be separated economically by single membrane units or hybrid processes where conventional separation units are combined with membrane-based processes. In this paper the advantages of carboxy group containing 6FDA (4,4′-hexafluoroisopropylidene diphthalic anhydride -copolyimides are discussed based on the experimental results for non cross-linked, ionically and covalently cross-linked membrane materials with respect to the separation of olefins/paraffins, e.g. propylene/propane, aromatic/aliphatic separation e.g. benzene/cyclohexane as well as high pressure gas separations, e.g. CO2/CH4 mixtures. In addition, opportunities for implementing the membrane units in conventional separation processes are discussed.

  19. [Formation of stabile cupola-like lipid bilayer membranes with a mobile plateau Gibbs boundary].

    Science.gov (United States)

    Shevchenko, E V; Smirnova, E Iu; Frolov, A V; Iakovenko, E V; Antonov, V F

    1993-01-01

    Stable bilayer lipid membrane with mobile Platear-Gibbs border have been formed. The predominant condition of the formation is the presence of lipid coverage on the teflon surface near the hole. The formation process includes transformation of the initial planar lipid bilayer into cupola-shaped one by bowing of the lipid bilayer due to hydrostatic pressure, movement of the PGb along the teflon surface. The bilayer area estimated by electric capacitance increases from 0.1 x 10(-8) F to 21 x 10(-8) F. Electric conductance of the lipid bilayer has not changed except for the phase transition and membrane collapse. The electric capacitance of the BLM formed from hydrogenated egg lecithin was changed by cooling between 60 degrees and 40 degrees C with the maximum at about phase transition range. The individual membrane sustains several scannings of the temperature without disruption which is an evidence of the stability of the cupola-shaped membranes.

  20. Tailoring of porosity of yttria-stabilized zirconia tubes as supports for oxygen separation membranes

    DEFF Research Database (Denmark)

    Bjørnetun Haugen, Astri; Kothanda Ramachandran, Dhavanesan; Gurauskis, Jonas

    Pure oxygen gas supplied by ceramic oxygen transport membranes can facilitate reduced CO2 emissions through more efficient gasification processes and CO2 capture and storage. Tubular membranes have some advantages compared to planar membranes, such as better resistance to thermal gradients and more...... straightforward sealing. The active oxygen separation layer in the membrane should be as thin as possible and therefore supported on a highly porous tubular substrate. In this work tubular porous supports of yttria-stabilized zirconia have been manufactured using thermoplastic extrusion. Two types of poreformers...... exceeding 55 % and gas permeabilities close to 10-14 m2 could be produced, demonstrating that thermoplastic extrusion is suitable for fabrication of porous and permeable tubes....

  1. Can Stabilization and Inhibition of Aquaporins Contribute to Future Development of Biomimetic Membranes?

    Science.gov (United States)

    To, Janet; Torres, Jaume

    2015-08-10

    In recent years, the use of biomimetic membranes that incorporate membrane proteins, i.e., biomimetic-hybrid membranes, has increased almost exponentially. Key membrane proteins in these systems have been aquaporins, which selectively permeabilize cellular membranes to water. Aquaporins may be incorporated into synthetic lipid bilayers or to more stable structures made of block copolymers or solid-state nanopores. However, translocation of aquaporins to these alien environments has adverse consequences in terms of performance and stability. Aquaporins incorporated in biomimetic membranes for use in water purification and desalination should also withstand the harsh environment that may prevail in these conditions, such as high pressure, and presence of salt or other chemicals. In this respect, modified aquaporins that can be adapted to these new environments should be developed. Another challenge is that biomimetic membranes that incorporate high densities of aquaporin should be defect-free, and this can only be efficiently ascertained with the availability of completely inactive mutants that behave otherwise like the wild type aquaporin, or with effective non-toxic water channel inhibitors that are so far inexistent. In this review, we describe approaches that can potentially be used to overcome these challenges.

  2. Can Stabilization and Inhibition of Aquaporins Contribute to Future Development of Biomimetic Membranes?

    Directory of Open Access Journals (Sweden)

    Janet To

    2015-08-01

    Full Text Available In recent years, the use of biomimetic membranes that incorporate membrane proteins, i.e., biomimetic-hybrid membranes, has increased almost exponentially. Key membrane proteins in these systems have been aquaporins, which selectively permeabilize cellular membranes to water. Aquaporins may be incorporated into synthetic lipid bilayers or to more stable structures made of block copolymers or solid-state nanopores. However, translocation of aquaporins to these alien environments has adverse consequences in terms of performance and stability. Aquaporins incorporated in biomimetic membranes for use in water purification and desalination should also withstand the harsh environment that may prevail in these conditions, such as high pressure, and presence of salt or other chemicals. In this respect, modified aquaporins that can be adapted to these new environments should be developed. Another challenge is that biomimetic membranes that incorporate high densities of aquaporin should be defect-free, and this can only be efficiently ascertained with the availability of completely inactive mutants that behave otherwise like the wild type aquaporin, or with effective non-toxic water channel inhibitors that are so far inexistent. In this review, we describe approaches that can potentially be used to overcome these challenges.

  3. Modelling of a tubular membrane contactor for pre-combustion CO2 capture using ionic liquids: Influence of the membrane configuration, absorbent properties and operation parameters

    Directory of Open Access Journals (Sweden)

    Zhongde Dai

    2016-10-01

    Full Text Available A membrane contactor using ionic liquids (ILs as solvent for pre-combustion capture CO2 at elevated temperature (303–393 K and pressure (20 bar has been studied using mathematic model in the present work. A comprehensive two-dimensional (2D mass-transfer model was developed based on finite element method. The effects of liquid properties, membrane configurations, as well as operation parameters on the CO2 removal efficiency were systematically studied. The simulation results show that CO2 can be effectively removed in this process. In addition, it is found that the liquid phase mass transfer dominated the overall mass transfer. Membranes with high porosity and small thickness could apparently reduce the membrane resistance and thus increase the separation efficiency. On the other hand, the membrane diameter and membrane length have a relatively small influence on separation performance within the operation range. Keywords: CO2 capture, Pre-combustion, Membrane contactor, Ionic liquids, Modelling

  4. Thin-film Nanofibrous Composite Membranes Containing Cellulose or Chitin Barrier Layers Fabricated by Ionic Liquids

    Energy Technology Data Exchange (ETDEWEB)

    H Ma; B Hsiao; B Chu

    2011-12-31

    The barrier layer of high-flux ultrafiltration (UF) thin-film nanofibrous composite (TFNC) membranes for purification of wastewater (e.g., bilge water) have been prepared by using cellulose, chitin, and a cellulose-chitin blend, regenerated from an ionic liquid. The structures and properties of regenerated cellulose, chitin, and a cellulose-chitin blend were analyzed with thermogravimetric analysis (TGA) and wide-angle X-ray diffraction (WAXD). The surface morphology, pore size and pore size distribution of TFNC membranes were determined by SEM images and molecular weight cut-off (MWCO) methods. An oil/water emulsion, a model of bilge water, was used as the feed solution, and the permeation flux and rejection ratio of the membranes were investigated. TFNC membranes based on the cellulose-chitin blend exhibited 10 times higher permeation flux when compared with a commercial UF membrane (PAN10, Sepro) with a similar rejection ratio after filtration over a time period of up to 100 h, implying the practical feasibility of such membranes for UF applications.

  5. Micro-electromembrane extraction across free liquid membranes. Instrumentation and basic principles

    OpenAIRE

    Kubáň, P. (Pavel); Boček, P. (Petr)

    2014-01-01

    Fundamental principles and instrumental set-up of a novel concept of electromembrane extraction downscaled to a micro-format is presented. In this set-up, free liquid membranes are applied, which are not anchored in any supporting material and their dimensions can be precisely defined. The extraction system is examined with a set of two, which enable real-time visualizations using a USB microscope camera.

  6. Selective extraction of uranium (VI) and thorium (IV) ions by liquid membrane technique

    International Nuclear Information System (INIS)

    Guey, N.; Cetisli, H.; Donat, R.

    2009-01-01

    Liquid membrane processes have a great importance for wastewater treatment, chemical engineering, and hydrometallurgy, biotechnological and biomedical applications. Liquid membrane process, one of the separation and purification techniques which are used for removal of the some metals and compounds causing environment and water pollution reduces the quantity of requirement of the solvents, prevents the environment pollution and becomes more economical as it combines extraction and stripping processes in one step. As uranium and thorium metals damage the environment and people's health, selective separation and refining processes will be useful for both the aspects of scientific and industrial applications. Because of trace amount and their radioactive structure, the industrial effects of recovering of both uranium and thorium or reducing the dangerous environmental effects, have a great importance. In this study, the function of transporting of uranium and thorium ions from aqueous solutions to the organic solutions and following, from organic solutions to aqueous solutions; the parameters of extraction technique and solvent type, solution of the pH, temperature, stirring speed, concentration of ions, concentration of reagent are investigated.The use of modelled system by supervisors is analyzed for the constant recovery application of related metals at the most effective conditions decided by the use of liquid membrane technique.

  7. Treatment of Medical Radioactive Liquid Waste Using Forward Osmosis (FO) Membrane Process

    KAUST Repository

    Lee, Songbok

    2018-04-07

    The use of forward osmosis (FO) for concentrating radioactive liquid waste from radiation therapy rooms in hospitals was systematically investigated in this study. The removal of natural and radioactive iodine using FO was first investigated with varying pHs and draw solutions (DSs) to identify the optimal conditions for FO concentration. Results showed that FO had a successful rejection rate for both natural and radioactive iodine (125I) of up to 99.3%. This high rejection rate was achieved at a high pH, mainly due to electric repulsion between iodine and membrane. Higher iodine removal by FO was also attained with a DS that exhibits a reverse salt flux (RSF) adequate to hinder iodine transport. Following this, actual radioactive medical liquid waste was collected and concentrated using FO under these optimal conditions. The radionuclides in the medical waste (131I) were removed effectively, but the water recovery rate was limited due to severe membrane fouling. To enhance the recovery rate, hydraulic washing was applied, but this had only limited success due to combined organic-inorganic fouling of the FO membrane. Finally, the effect of FO concentration on the reduction of septic tank volume was simulated as a function of recovery rate. To our knowledge, this study is the first attempt to explore the potential of FO technology for treating radioactive waste, and thus could be expanded to the dewatering of the radioactive liquid wastes from a variety of sources, such as nuclear power plants.

  8. Microporous hollow fibre membrane modules as gas-liquid contactors. Part 1: Physical mass transfer processes. A specific application: mass transfer in highly viscous liquids

    OpenAIRE

    Kreulen, H.; Kreulen, H.; Versteeg, Geert; Smolders, C.A.; Smolders, C.A.; van Swaaij, Willibrordus Petrus Maria

    1993-01-01

    Gas-liquid mass transfer has been studied in a membrane module with non-wetted microporous fibres in the laminar flow regime. This new type of gas/liquid contactor can be operated stabily over a large range of gas and liquid flows because gas and liquid phase do not influence each other directly. Therefore foam is not formed in the module, gas bubbles are not entrained in the liquid flowing out of the reactor and the separation of both phases can be achieved very easily. These phenomena often...

  9. REMOVAL OF COPPER IONS USING ALIQUAT 336/TBP BASED SUPPORTED LIQUID MEMBRANE

    Directory of Open Access Journals (Sweden)

    Baghdad Medjahed

    2014-03-01

    Full Text Available The sorption of copper (II present in an aqueous media using a supported liquid membrane (SLM by chloride tri-N-octylmethylammonium (Aliquat 336 and Tri-n-butylphosphate (TBP from molar ratio 1:1, with polytetrafluoroethylene (PTFE as a membrane support was studied. The effects of various parameters as initial pH, KSCN concentration and ammonium acetate concentration on the extraction yield were carried out. By a calculation program using CHEAQS V. L20.1, the determination of the percentages of the present species before and after extraction were given, in aqueous medium and on the membrane to be able to determine the relation between the nature of the extracted species and the extraction yield. The 23 factorial design achieve the best conditions of recovery procedure. The recovery of copper (II is almost quantitative (94 %, in one step.

  10. Emulsion liquid membrane for selective extraction of bismuth from nitrate medium

    International Nuclear Information System (INIS)

    Mokhtari, Bahram; Pourabdollah, Kobra

    2013-01-01

    The novelty of this work is the selective extraction of bismuth ions from nitrate medium by emulsion liquid membrane. Di(2-ethylhexyl)phosphoric acid was used as extractant of bismuth ions from nitrate medium by emulsion liquid membrane, and Triton X-100 was used as the biodegradable surfactant in n-pentanol n-pentanol bulk membrane. The extraction of bismuth ions was evaluated by the yield of extraction. The experimental parameters were evaluated and were optimized. They included the ratio of di(2-ethylhexyl)phosphoric acid concentration to the concentration of /Triton X-100 concentration (1.0 : 0.5% w/w), nature of diluents (n-pentanol), nature and concentration of the stripping solution (sulfuric acid, 0.5M), stirring speed (1,800 rpm) and equilibrium time of extraction (20min), initial feed solution of bismuth (350 ppm) and the volume ratio of the internal stripping phase to the membrane phase (14 times). The experimental parameters of kinetic extraction revealed that the bismuth ions were extracted at 100% 97%

  11. Emulsion liquid membrane for selective extraction of bismuth from nitrate medium

    Energy Technology Data Exchange (ETDEWEB)

    Mokhtari, Bahram; Pourabdollah, Kobra [Islamic Azad University, Shahreza (Iran, Islamic Republic of)

    2013-07-15

    The novelty of this work is the selective extraction of bismuth ions from nitrate medium by emulsion liquid membrane. Di(2-ethylhexyl)phosphoric acid was used as extractant of bismuth ions from nitrate medium by emulsion liquid membrane, and Triton X-100 was used as the biodegradable surfactant in n-pentanol n-pentanol bulk membrane. The extraction of bismuth ions was evaluated by the yield of extraction. The experimental parameters were evaluated and were optimized. They included the ratio of di(2-ethylhexyl)phosphoric acid concentration to the concentration of /Triton X-100 concentration (1.0 : 0.5% w/w), nature of diluents (n-pentanol), nature and concentration of the stripping solution (sulfuric acid, 0.5M), stirring speed (1,800 rpm) and equilibrium time of extraction (20min), initial feed solution of bismuth (350 ppm) and the volume ratio of the internal stripping phase to the membrane phase (14 times). The experimental parameters of kinetic extraction revealed that the bismuth ions were extracted at 100% 97%.

  12. Ceramic membrane fouling during ultrafiltration of oil/water emulsions: roles played by stabilization surfactants of oil droplets.

    Science.gov (United States)

    Lu, Dongwei; Zhang, Tao; Ma, Jun

    2015-04-07

    Oil/water (O/W) emulsion stabilized by surfactants is the part of oily wastewater that is most difficult to handle. Ceramic membrane ultrafiltration presently is an ideal process to treat O/W emulsions. However, little is known about the fouling mechanism of the ceramic membrane during O/W emulsion treatment. This paper investigated how stabilization surfactants of O/W emulsions influence the irreversible fouling of ceramic membranes during ultrafiltration. An unexpected phenomenon observed was that irreversible fouling was much less when the charge of the stabilization surfactant of O/W emulsions is opposite to the membrane. The less ceramic membrane fouling in this case was proposed to be due to a synergetic steric effect and demulsification effect which prevented the penetration of oil droplets into membrane pores and led to less pore blockage. This proposed mechanism was supported by cross section images of fouled and virgin ceramic membranes taken with scanning electron microscopy, regression results of classical fouling models, and analysis of organic components rejected by the membrane. Furthermore, this mechanism was also verified by the existence of a steric effect and demulsification effect. Our finding suggests that ceramic membrane oppositely charged to the stabilization surfactant should be applied in ultrafiltration of O/W emulsions to alleviate irreversible membrane fouling. It could be a useful rule for ceramic membrane ultrafiltration of oily wastewater.

  13. Ceramic membrane fouling during ultrafiltration of oil/water emulsions: Roles played by stabilization surfactants of oil droplets

    KAUST Repository

    Lu, Dongwei

    2015-04-07

    Oil/water (O/W) emulsion stabilized by surfactants is the part of oily wastewater that is most difficult to handle. Ceramic membrane ultrafiltration presently is an ideal process to treat O/W emulsions. However, little is known about the fouling mechanism of the ceramic membrane during O/W emulsion treatment. This paper investigated how stabilization surfactants of O/W emulsions influence the irreversible fouling of ceramic membranes during ultrafiltration. An unexpected phenomenon observed was that irreversible fouling was much less when the charge of the stabilization surfactant of O/W emulsions is opposite to the membrane. The less ceramic membrane fouling in this case was proposed to be due to a synergetic steric effect and demulsification effect which prevented the penetration of oil droplets into membrane pores and led to less pore blockage. This proposed mechanism was supported by cross section images of fouled and virgin ceramic membranes taken with scanning electron microscopy, regression results of classical fouling models, and analysis of organic components rejected by the membrane. Furthermore, this mechanism was also verified by the existence of a steric effect and demulsification effect. Our finding suggests that ceramic membrane oppositely charged to the stabilization surfactant should be applied in ultrafiltration of O/W emulsions to alleviate irreversible membrane fouling. It could be a useful rule for ceramic membrane ultrafiltration of oily wastewater. © 2015 American Chemical Society.

  14. Stabilization of liquid low-level and mixed wastes: a treatability study

    International Nuclear Information System (INIS)

    Carson, S.; Cheng, Yu-Cheng; Yellowhorse, L.; Peterson, P.

    1996-01-01

    A treatability study has been conducted on liquid low-level and mixed wastes using the stabilization agents Aquaset, Aquaset II, Aquaset II-H, Petroset, Petroset-H, and Petroset and Petroset II. A total of 40 different waste types with activities ranging from 10 -14 to 10 -4 curies/ml have been stabilized. Reported data for each waste include its chemical and radiological composition and the optimum composition or range of compositions (weight of agent/volume of waste) for each stabilization agent used. All wastes were successfully stabilized with one or more of the stabilization agents and all final waste forms passed the Paint Filter Liquids Test (EPA Method 9095)

  15. Stabilization of liquid low-level and mixed wastes: a treatability study

    Energy Technology Data Exchange (ETDEWEB)

    Carson, S.; Cheng, Yu-Cheng; Yellowhorse, L.; Peterson, P.

    1996-02-01

    A treatability study has been conducted on liquid low-level and mixed wastes using the stabilization agents Aquaset, Aquaset II, Aquaset II-H, Petroset, Petroset-H, and Petroset and Petroset II. A total of 40 different waste types with activities ranging from 10{sup {minus}14} to 10{sup {minus}4} curies/ml have been stabilized. Reported data for each waste include its chemical and radiological composition and the optimum composition or range of compositions (weight of agent/volume of waste) for each stabilization agent used. All wastes were successfully stabilized with one or more of the stabilization agents and all final waste forms passed the Paint Filter Liquids Test (EPA Method 9095).

  16. Correcting the wavefront aberration of membrane mirror based on liquid crystal spatial light modulator

    Science.gov (United States)

    Yang, Bin; Wei, Yin; Chen, Xinhua; Tang, Minxue

    2014-11-01

    Membrane mirror with flexible polymer film substrate is a new-concept ultra lightweight mirror for space applications. Compared with traditional mirrors, membrane mirror has the advantages of lightweight, folding and deployable, low cost and etc. Due to the surface shape of flexible membrane mirror is easy to deviate from the design surface shape, it will bring wavefront aberration to the optical system. In order to solve this problem, a method of membrane mirror wavefront aberration correction based on the liquid crystal spatial light modulator (LCSLM) will be studied in this paper. The wavefront aberration correction principle of LCSLM is described and the phase modulation property of a LCSLM is measured and analyzed firstly. Then the membrane mirror wavefront aberration correction system is designed and established according to the optical properties of a membrane mirror. The LCSLM and a Hartmann-Shack sensor are used as a wavefront corrector and a wavefront detector, respectively. The detected wavefront aberration is calculated and converted into voltage value on LCSLM for the mirror wavefront aberration correction by programming in Matlab. When in experiment, the wavefront aberration of a glass plane mirror with a diameter of 70 mm is measured and corrected for verifying the feasibility of the experiment system and the correctness of the program. The PV value and RMS value of distorted wavefront are reduced and near diffraction limited optical performance is achieved. On this basis, the wavefront aberration of the aperture center Φ25 mm in a membrane mirror with a diameter of 200 mm is corrected and the errors are analyzed. It provides a means of correcting the wavefront aberration of membrane mirror.

  17. Signal Processing Methods for Liquid Rocket Engine Combustion Stability Assessments

    Science.gov (United States)

    Kenny, R. Jeremy; Lee, Erik; Hulka, James R.; Casiano, Matthew

    2011-01-01

    The J2X Gas Generator engine design specifications include dynamic, spontaneous, and broadband combustion stability requirements. These requirements are verified empirically based high frequency chamber pressure measurements and analyses. Dynamic stability is determined with the dynamic pressure response due to an artificial perturbation of the combustion chamber pressure (bomb testing), and spontaneous and broadband stability are determined from the dynamic pressure responses during steady operation starting at specified power levels. J2X Workhorse Gas Generator testing included bomb tests with multiple hardware configurations and operating conditions, including a configuration used explicitly for engine verification test series. This work covers signal processing techniques developed at Marshall Space Flight Center (MSFC) to help assess engine design stability requirements. Dynamic stability assessments were performed following both the CPIA 655 guidelines and a MSFC in-house developed statistical-based approach. The statistical approach was developed to better verify when the dynamic pressure amplitudes corresponding to a particular frequency returned back to pre-bomb characteristics. This was accomplished by first determining the statistical characteristics of the pre-bomb dynamic levels. The pre-bomb statistical characterization provided 95% coverage bounds; these bounds were used as a quantitative measure to determine when the post-bomb signal returned to pre-bomb conditions. The time for post-bomb levels to acceptably return to pre-bomb levels was compared to the dominant frequency-dependent time recommended by CPIA 655. Results for multiple test configurations, including stable and unstable configurations, were reviewed. Spontaneous stability was assessed using two processes: 1) characterization of the ratio of the peak response amplitudes to the excited chamber acoustic mode amplitudes and 2) characterization of the variability of the peak response

  18. Sedative, membrane stability, cytotoxic and antioxidant properties of methanol extract of leaves of Protium serratum Wall.

    Directory of Open Access Journals (Sweden)

    Md. Rafikul Islam

    2014-09-01

    Full Text Available Objective: To study the sedative, membrane stability, cytotoxic and antioxidant properties of the leaves of Protium serratum extracted using methanol. Methods: Sedative test was performed using hole cross and open field methods at 200 and 400 mg/kg. Membrane stability of red blood cell was used for anti-inflammatory test at different concentrations. Cytotoxic study was performed using brine shrimp lethality test. Total flavonoid contents, total phenol contents and reducing power were used to assess antioxidant properties of the extract. Results: Extract showed better sedative action at lower doses in both experiments. Maximum 73.33% locomotion reduction was found at 200 mg/kg at 1 20 min and that was 89.29% for diazepam in hole cross test. In membrane stability test, extract and standard drug diclofenac have 35.66% and 91.20% stability, respectively. LC50 value of the extract was 22.91 µg/mL. Total phenol and flavonoid contents were (55.53依14.63 mg gallic acid equivalent per gram of extract and (1 06.33依7.35 mg of quercetin equivalent per gram of extract, respectively per gram of extract. Significant reducing power was observed as compared to ascorbic acid. Conclusions: Extract possesses good pharmacological properties. Hence, further extensive study is essential to find out possible active constituents for the treatment of anxiety, inflammation or sickle cell disease, cancer and free radical mediated abnormalities.

  19. Chemical stability of enalapril maleate drug substance and tablets by a stability-indicating liquid chromatographic method

    Directory of Open Access Journals (Sweden)

    Marta de Diego

    2011-01-01

    Full Text Available The chemical stability of enalapril drug substance and tablets was studied by a stability-indicating liquid chromatographic method. Stress testing was performed on drug substance under various conditions. Accelerated stability testing was carried out for different formulations of enalapril tablets. Chromatographic separation was achieved on a RP-18 column, using a mobile phase of methanol phosphate buffer at 1.0 mL min"1 and UV detection. Degradation of the drug substance was greater under hydrolytic conditions. After 180 days of accelerated stability testing most enalapril tablets showed more than 10% of degradation. Enalapril drug substance and tablets showed instability under stress and accelerated testing respectively, with possible implications on the therapeutic activity.

  20. Temperature stabilization near Tsub(lambda) in liquid helium

    International Nuclear Information System (INIS)

    Francois, M.; Lhuillier, D.

    1975-01-01

    The study of He I and II equilibrium properties near the lambda transition requires a very performant temperature stabilisation. A system using second or fourth sound and which offers a stability better than 10 -8 0 K/hour in the temperature range 1.8 0 K-2.2 0 K is presented. (Auth.)

  1. Thermal stability of liquid antioxidative extracts from pomegranate peel

    Science.gov (United States)

    This research was carried out to assess the potential of using the natural antioxidants in pomegranate peel extracts as replacement for synthetic antioxidants. As a result the thermal stability of pomegranate peel extract products during sterilization and storage, and its effect on industrial, color...

  2. Storage stability of sterilized liquid extracts from pomegranate peel

    Science.gov (United States)

    Pomegranate marc, a byproduct of commercial juice production, has shown promise as a starting material for the recovery of health promoting phenolic compounds. The stability of aqueous extracts prepared from pomegranate marc was evaluated in preparation to directly using these extracts as nutraceuti...

  3. Techniques for Liquid Rocket Combustion Spontaneous Stability and Rough Combustion Assessments

    Science.gov (United States)

    Kenny, R. J.; Giacomoni, C.; Casiano, M. J.; Fischbach, S. R.

    2016-01-01

    This work presents techniques for liquid rocket engine combustion stability assessments with respect to spontaneous stability and rough combustion. Techniques covering empirical parameter extraction, which were established in prior works, are applied for three additional programs: the F-1 Gas Generator (F1GG) component test program, the RS-84 preburner component test program, and the Marshall Integrated Test Rig (MITR) program. Stability assessment parameters from these programs are compared against prior established spontaneous stability metrics and updates are identified. Also, a procedure for comparing measured with predicted mode shapes is presented, based on an extension of the Modal Assurance Criterion (MAC).

  4. Composites of ionic liquid and amine-modified SAPO 34 improve CO2 separation of CO2-selective polymer membranes

    Science.gov (United States)

    Hu, Leiqing; Cheng, Jun; Li, Yannan; Liu, Jianzhong; Zhang, Li; Zhou, Junhu; Cen, Kefa

    2017-07-01

    Mixed matrix membranes with ionic liquids and molecular sieve particles had high CO2 permeabilities, but CO2 separation from small gas molecules such as H2 was dissatisfied because of bad interfacial interaction between ionic liquid and molecular sieve particles. To solve that, amine groups were introduced to modify surface of molecular sieve particles before loading with ionic liquid. SAPO 34 was adopted as the original filler, and four mixed matrix membranes with different fillers were prepared on the outer surface of ceramic hollow fibers. Both surface voids and hard agglomerations disappeared, and the surface became smooth after SAPO 34 was modified by amine groups and ionic liquid [P66614][2-Op]. Mixed matrix membranes with composites of amine-modified SAPO 34 and ionic liquid exhibited excellent CO2 permeability (408.9 Barrers) and CO2/H2 selectivity (22.1).

  5. Poly(ionic liquid)/Ionic Liquid Ion-Gels with High "Free" Ionic Liquid Content: Platform Membrane Materials for CO2/Light Gas Separations.

    Science.gov (United States)

    Cowan, Matthew G; Gin, Douglas L; Noble, Richard D

    2016-04-19

    -films (ca. 100-nm-thick active layer). Traditional polymeric membrane materials are limited by a trade-off between permeability and selectivity empirically described by the "Robeson upper bound"-placing the desired membrane properties beyond reach. Therefore, the investigation of advanced and composite materials that can overcome the limitations of traditional polymeric materials is the focus of significant academic and industrial research. In particular, there has been substantial work on ionic-liquid (IL)-based materials due to their gas transport properties. This review provides an overview of our collaborative work on developing poly(ionic liquid)/ionic liquid (PIL/IL) ion-gel membrane technology. We detail developmental work on the preparation of PIL/IL composites and describe how this chemical technology was adapted to allow the roll-to-roll processing and preparation of membranes with defect-free active layers ca. 100 nm thick, CO2 permeances of over 6000 GPU, and CO2/N2 selectivity of ≥20-properties with the potential to reduce the cost of CO2 removal from coal-fired power plant flue gas to ca. $15 per ton of CO2 captured. Additionally, we examine the materials developments that have produced advanced PIL/IL composite membranes. These advancements include cross-linked PIL/IL blends, step-growth PIL/IL networks with facilitated transport groups, and PIL/IL composites with microporous additives for CO2/CH4 separations.

  6. Advanced Supported Liquid Membranes for CO2 Control in Extravehicular Activity Applications

    Science.gov (United States)

    Wickham, David T.; Gleason, Kevin J.; Engel, Jeffrey R.; Cowley, Scott W.; Chullen, Cinda

    2014-01-01

    Developing a new, robust, portable life support system (PLSS) is currently a high priority for NASA in order to support longer and safer extravehicular activity (EVA) missions. One of the critical PLSS functions is maintaining the carbon dioxide (CO2) concentration in the suit at acceptable levels. Although the Metal Oxide (MetOx) canister has worked well, it has a finite CO2 adsorption capacity. Consequently, the unit would have to be larger and heavier to extend EVA times. Therefore, new CO2 control technologies must be developed to meet mission objectives without increasing the size of the PLSS. Although recent work has centered on sorbents that can be regenerated during the EVA, this strategy increases the system complexity and power consumption. A simpler approach is to use a membrane that selectively vents CO2 to space. A membrane has many advantages over current technology: it is a continuous system with no theoretical capacity limit, it requires no consumables, and it requires no hardware for switching beds between absorption and regeneration. Unfortunately, conventional gas separation membranes do not have adequate selectivity for use in the PLSS. However, the required performance could be obtained with a supported liquid membrane (SLM), which consists of a micro porous material filled with a liquid that selectively reacts with CO2 over oxygen (O2). In a current Phase II SBIR project, Reaction Systems has developed a new reactive liquid, which has effectively zero vapor pressure making it an ideal candidate for use in an SLM. The SLM function has been demonstrated with representative pressures of CO2, O2, and water (H2O). In addition to being effective for CO2 control, the SLM also vents moisture to space. Therefore, this project has demonstrated the feasibility of using an SLM to control CO2 in an EVA application.

  7. Improving oxidative stability of liquid fish oil supplements for pets

    DEFF Research Database (Denmark)

    Thomsen, Birgitte Raagaard; Griinari, Mikko; Jacobsen, Charlotte

    2017-01-01

    of fish oil by adding vegetable oils, mixed tocopherols and rosemary extract, and to formulate a commercial product according to the results obtained. The formulated product was evaluated against commercial fish oil products. An initial screening for antioxidative effect was performed by using Oxipres...... equipment. The effect of antioxidant and vegetable oil blends was examined in oils stored at 30 and 40°C by measuring peroxide value, volatile compounds with GC-MS and tocopherol content. Addition of vegetable oil and rosemary extract at high level (4000–6000 ppm) plus 600 ppm of mixed tocopherols increased...... oxidative stability to the same extent as 2000 ppm mixed tocopherols in Oxipres. Overall, oxidative stability of fish oil or fish oil + vegetable oil blends was improved the most by addition of 5000 ppm rosemary extract and 500 ppm mixed tocopherols. A commercial oil blend with composition optimized based...

  8. Production of Jet Fuels from Coal-Derived Liquids. Volume 13. Evaluation of Storage and Thermal Stability of Jet Fuels Derived from Coal Liquids

    Science.gov (United States)

    1990-05-01

    coal liquids including the hydrotreated tar oil distillates from the GPGP. Thus, determination of the storage and thermal stabilities of jet fuel...AD-A224 576 AFWAL-TR-87-2042 Volume XIII PRODUCTION OF JET FUELS FROM COAL -DERIVED LIQUIDS VOL XIII - Evaluation of Storage and Thermal Stability of...Jet Fuels Derived from Coal Liquids G. P. Sturm, Jr., R. D. Grigsby, J. W. Goetzinger, J. B. Green, and R. P. Anderson lIT Research Institute National

  9. The binary eutectic of NSAIDS and two-phase liquid system for enhanced membrane permeation.

    Science.gov (United States)

    Yuan, Xudong; Capomacchia, A C

    2005-01-01

    The eutectic properties of binary mixtures of some nonsteroidal anti-inflammatory drugs (NSAIDs) with ibuprofen were studied using differential scanning calorimetry (DSC) and phase equilibrium diagrams. The melting points of selected NSAIDs were significantly depressed due to binary eutectic formation with ibuprofen. Ketoprofen and ibuprofen were selected to study the effect of eutectic formation on membrane permeation using Franz diffusion cells and snake skin as the model membrane. The presence of aqueous isopropyl alcohol (IPA) was necessary to completely transform the solid drugs into an oily state at ambient temperature. As much as the 99.6% of ibuprofen and the 88.8% of ketoprofen added were found in the oily phase of the two-phase liquid system formed when aqueous IPA was added to the eutectic mixture. Due to the high drug concentration in the oily phase, and maximum thermodynamic activity, the two-phase liquid system showed enhanced membrane permeation rates of ibuprofen (37.5 microg/cm2/hr) and ketoprofen (33.4 microg/cm2/hr) compared to other reference preparations used.

  10. utilization of adsorption and/or liquid membranes techniques in treatment of some hazardous substances

    International Nuclear Information System (INIS)

    Hussin, L.M.S.

    2011-01-01

    environmental pollution, as a consequence of the industrialization process, is one of the major problems that has to be solved and controlled. The most important treatment processes for metals and dyes contaminated waste streams include chemical precipitation, membrane, filtration, ion exchange, carbon adsorption and coprecipitation/adsorption. However, all these techniques have their inherent advantages and limitations in applications. These processes usually need expensive facility and high maintenance cost. Therefore, there is a need for more economical alternative technologies for the treatment of metals and dyes contaminated waste streams. The aim of present work is to study the treatment of some hazardous substances such as heavy metals e.g. ( lead, cobalt and strontium) and dyes e.g. ( acid red 73, and acid blue 74 ) using either adsorption or liquid emulsion membrane techniques. The experimental part deals with the application of adsorption and liquid emulsion membrane techniques for removal of some hazardous substances such as metal ions ( lead, cobalt and strontium) and dyes (acid red 73 and acid blue 74). All the apparatus and techniques employed were described.

  11. Partial delignification of wood and membrane preparation using a quaternary ammonium ionic liquid

    Science.gov (United States)

    Miao, Jiaojiao; Yu, Yongqi; Jiang, Zeming; Tang, Lan; Zhang, Liping

    2017-03-01

    This work determined that southern yellow pine wood can almost be completely dissolved in the quaternary ammonium ionic liquid tetrabutylammonium acetate with dimethyl sulfoxide (in a 2:8 mass ratio), after minimal grinding, upon heating at 85 °C for three dissolution/reconstitution cycles, each 1.5 h. Approximately 34.6% of the native lignin and 67.4% of the native carbohydrates present in the original wood can subsequently be extracted, respectively, and were assessed. A gradual decrease in lignin with increased extraction cycles resulted in increased crystallinity index of the cellulose II in the cellulose-rich residue, as confirmed by X-ray diffraction. An increasingly homogeneous macrostructure in the cellulose-rich residue was also evident from scanning electron microscopy images. Membranes cast directly from either wood or cellulose-rich residue solutions in the same tetrabutylammonium acetate/dimethyl sulfoxide system, were prepared using a papermaking-like process. Morphological and mechanical studies indicated that lignin extraction made the membranes more uniform and flexible. Systematic increases in the fibril lengths and orientations of the recovered materials were also found with decreasing lignin contents on the basis of atomic force microscopy analysis. This work demonstrates that relatively efficient partial separation of pine wood and subsequent membrane preparation are possible using a quaternary ammonium ionic liquid.

  12. Polymer Stabilization of Liquid-Crystal Blue Phase II toward Photonic Crystals.

    Science.gov (United States)

    Jo, Seong-Yong; Jeon, Sung-Wook; Kim, Byeong-Cheon; Bae, Jae-Hyun; Araoka, Fumito; Choi, Suk-Won

    2017-03-15

    The temperature ranges where a pure simple-cubic blue phase (BPII) emerges are quite narrow compared to the body-centered-cubic BP (BPI) such that the polymer stabilization of BPII is much more difficult. Hence, a polymer-stabilized BPII possessing a wide temperature range has been scarcely reported. Here, we fabricate a polymer-stabilized BPII over a temperature range of 50 °C including room temperature. The fabricated polymer-stabilized BPII is confirmed via polarized optical microscopy, Bragg reflection, and Kossel diagram observations. Furthermore, we demonstrate reflective BP liquid-crystal devices utilizing the reflectance-voltage performance as a potential application of the polymer-stabilized BPII. Our work demonstrates the possibility of practical application of the polymer-stabilized BPII to photonic crystals.

  13. Electrohydrodynamic stability of two stratified power law liquid in couette flow

    International Nuclear Information System (INIS)

    Eldabe, N.T.

    1988-01-01

    Consideration is given to the stability of the flow of two power law liquids under the influence of normal electric field between two infinite parallel planes when one of the planes moves with constant velocity in its own plane. It is found that the electric fields have a dramatic effect and can be chosen to stabilize or destabilize the flow. The effects of the power law parameters on the problem are examinated

  14. Microporous hollow fibre membrane modules as gas-liquid contactors. Part 1. Physical mass transfer processes: A specific application

    OpenAIRE

    Kreulen, H.; Versteeg, G.F.; Swaaij, W.P.M. van

    1993-01-01

    Gas-liquid mass transfer has been studied in a membrane module with non-wetted microporous fibres in the laminar flow regime. This new type of gas/liquid contactor can be operated stabily over a large range of gas and liquid flows because gas and liquid phase do not influence each other directly. Therefore foam is not formed in the module, gas bubbles are not entrained in the liquid flowing out of the reactor and the separation of both phases can be achieved very easily. These phenomena often...

  15. Parallel artificial liquid membrane extraction as an efficient tool for removal of phospholipids from human plasma.

    Science.gov (United States)

    Ask, Kristine Skoglund; Bardakci, Turgay; Parmer, Marthe Petrine; Halvorsen, Trine Grønhaug; Øiestad, Elisabeth Leere; Pedersen-Bjergaard, Stig; Gjelstad, Astrid

    2016-09-10

    Generic Parallel Artificial Liquid Membrane Extraction (PALME) methods for non-polar basic and non-polar acidic drugs from human plasma were investigated with respect to phospholipid removal. In both cases, extractions in 96-well format were performed from plasma (125μL), through 4μL organic solvent used as supported liquid membranes (SLMs), and into 50μL aqueous acceptor solutions. The acceptor solutions were subsequently analysed by liquid chromatography-tandem mass spectrometry (LC-MS/MS) using in-source fragmentation and monitoring the m/z 184→184 transition for investigation of phosphatidylcholines (PC), sphingomyelins (SM), and lysophosphatidylcholines (Lyso-PC). In both generic methods, no phospholipids were detected in the acceptor solutions. Thus, PALME appeared to be highly efficient for phospholipid removal. To further support this, qualitative (post-column infusion) and quantitative matrix effects were investigated with fluoxetine, fluvoxamine, and quetiapine as model analytes. No signs of matrix effects were observed. Finally, PALME was evaluated for the aforementioned drug substances, and data were in accordance with European Medicines Agency (EMA) guidelines. Copyright © 2016 Elsevier B.V. All rights reserved.

  16. Experimental investigation of the stability of a moving radial liquid sheet

    Science.gov (United States)

    Paramati, Manjula; Tirumkudulu, Mahesh

    2013-11-01

    Experiments were conducted to understand the stability of moving radial liquid sheets formed by the head-on impingement of two co-linear water jets using laser induced fluorescence technique (LIF). Acoustic sinusoidal fluctuations were introduced at the jet impingement point and we measured the displacement of the center line of the liquid sheet (sinuous mode) and the thickness variation (varicose mode) of the disturbed liquid sheet. Our experiments show that the sinuous disturbances grow as they are convected outward in the radial direction even in the smooth regime (We theory by Tirumkudulu and Paramati (Communicated to Phys. Of Fluids, 2013) which accounts for the inertia of the liquid phase and the surface tension force in a radial liquid sheet while neglecting the inertial effects due to the surrounding gas phase. The authors acknowledge the financial assistance from Indo-French Center for Pro- motion of Advanced Research and also Indian institute of technology Bombay.

  17. Study of structural stability and damaging effect on membrane for four Aβ42 dimers.

    Directory of Open Access Journals (Sweden)

    Wei Feng

    Full Text Available Increasing evidence shows that Aβ oligomers are key pathogenic molecules in Alzheimer's disease. Among Aβ oligomers, dimer is the smallest aggregate and toxic unit. Therefore, understanding its structural and dynamic properties is quite useful to prevent the formation and toxicity of the Aβ oligomers. In this study, we performed molecular dynamic simulations on four Aβ42 dimers, 2NCb, CNNC, NCNC and NCCN, within the hydrated DPPC membrane. Four Aβ42 dimers differ in the arrangements of two Aβ42 peptides. This study aims to investigate the impact of aggregation pattern of two Aβ peptides on the structural stability of the Aβ42 dimer and its disruption to the biological membrane. The MD results demonstrate that the NCCN, CNNC and NCNC have the larger structural fluctuation at the N-terminus of Aβ42 peptide, where the β-strand structure converts into the coil structure. The loss of the N-terminal β-strand further impairs the aggregate ability of Aβ42 dimer. In addition, inserting Aβ42 dimer into the membrane can considerably decrease the average APL of DPPC membrane. Moreover this decrease effect is largely dependent on the distance to the location of Aβ42 dimer and its secondary structure forms. Based on the results, the 2NCb is considered as a stable dimeric unit for aggregating the larger Aβ42 oligomer, and has a potent ability to disrupt the membrane.

  18. One-step extraction of polar drugs from plasma by Parallel Artificial Liquid Membrane Extraction

    DEFF Research Database (Denmark)

    Pilařová, Veronika; Sultani, Mumtaz; Ask, Kristine Skoglund

    2017-01-01

    -throughput is achievable, in addition to the green chemistry offered by using PALME. The consumption of organic solvent is minimized to 3-5μL per sample. With a sample volume of 250μL and acceptor solution volume of 50μL, a maximal enrichment factor of five is achievable. Based on these parameters, a new method...... for extraction of polar basic drugs was developed in the present work. The basic drugs hydralazine, ephedrine, metaraminol, salbutamol, and cimetidine were used as model analytes, and were extracted from alkalized human plasma into an aqueous solution via the supported liquid membrane. The extraction...... was promoted by a carrier dissolved in the membrane, creating a temporary ion-pair complex between the hydrophilic drug and the carrier. As the model analytes were extracted directly into an aqueous solution, there was no need for evaporation of the extract before injection into LC-MS. Hence, the sample...

  19. Liquid membrane ion-selective electrodes for potentiometric dosage of coper and nickel

    Directory of Open Access Journals (Sweden)

    MARIA PLENICEANY

    2005-02-01

    Full Text Available This paper presents experimental and theoretical data regarding the preparation and characterization of three liquid-membrane electrodes, which have not been mentioned in the specialized literature so far. The active substances, the solutions of which in nitrobenzene formed the membranes on a graphite rod, are simple complex combinations of Cu(II and Ni(II ions with an organic ligand belonging to the Schiff base class: N-[2-thienylmethilidene]-2-aminoethanol (TNAHE. The Cu2+ -selective and Ni2+ -selective electrodes were used to determine the copper and nickel ions in aqueous solutions, both by direct potentiometry and by potentiometric titration with EDTA. They were also used for the determination of Cu2+ and Ni2+ ions in industrial waters by direct potentiometry.

  20. Efficacy of Ultrasonic Homogenization in the Separation of Benzene-n-Heptane Mixture by Liquid Membrane

    Energy Technology Data Exchange (ETDEWEB)

    Kim, B.S.; Chung, T.S. [Department of Chemical Engineering, Sung Kyun Kwan University, Seoul (Korea)

    1999-04-01

    In the separation of benzene-n-heptane mixture by liquid membrane, the efficacy of ultrasonic homogenization in emulsification was studied with two anionic surfactants. The two anionic surfactants used were triethanolamine lauryl sulfate and sodium polyoxyethylene(2) lauryl ether sulfate. The two anionic surfactants used were triethanolamine lauryl sulfate and sodium polyoxyethylene(2) lauryl ether stifle. The highest value of the separation factor obtained by ultrasonic homogenization was approximately three times as large as that for triethanolamine lauryl sulfate and one and a half times as large as that for sodium polyoxyethylene(2) lauryl sulfate when the mechanical stirring was used on the same operational conditions. The lowest membrane breakup was observed when the highest value of the separation factor was achieved with sodium polyoxyethylene(2) lauryl sulfate. 14 refs., 7 figs., 1 tab.

  1. Removal of acetic acid from simulated hemicellulosic hydrolysates by emulsion liquid membrane with organophosphorus extractants.

    Science.gov (United States)

    Lee, Sang Cheol

    2015-09-01

    Selective removal of acetic acid from simulated hemicellulosic hydrolysates containing xylose and sulfuric acid was attempted in a batch emulsion liquid membrane (ELM) system with organophosphorus extractants. Various experimental variables were used to develop a more energy-efficient ELM process. Total operation time of an ELM run with a very small quantity of trioctylphosphine oxide as the extractant was reduced to about a third of those required to attain almost the same extraction efficiency as obtained in previous ELM works without any extractant. Under specific conditions, acetic acid was selectively separated with a high degree of extraction and insignificant loss of xylose, and its purity and enrichment ratio in the stripping phase were higher than 92% and 6, respectively. Also, reused organic membrane solutions exhibited the extraction efficiency as high as fresh organic solutions did. These results showed that the current ELM process would be quite practical. Copyright © 2015 Elsevier Ltd. All rights reserved.

  2. Surface modification of poly(vinylidene fluoride) hollow fibre membranes for biogas purification in a gas–liquid membrane contactor system

    Science.gov (United States)

    Huang, Chuan; Li, Jiaxiang; Shen, Yadong; Wang, Liao

    2017-01-01

    The wetting of hollow fibre membranes decreases the performance of the liquid–gas membrane contactor for CO2 capture in biogas upgrading. To solve this problem, in this work, a poly(vinylidene fluoride) (PVDF) hollow fibre membrane for a liquid–gas membrane contactor was coated with a superhydrophobic layer composed of a combination of hydrophobic SiO2 nanoparticles and polydimethylsiloxane (PDMS) by the method of spray deposition. A rough layer of SiO2 deposited on the PVDF membrane resulted in an enhanced surface hydrophobicity. The surface structure of the pristine PVDF significantly affected the homogeneity of the generated SiO2 layer. A uniform surface coating on the PVDF upper layer resulted from the presence of micrometre and nanometre-sized roughness on the surface of the PVDF membrane, which was achieved with a SiO2 concentration of 4.44 mg ml−1 (0.2 g/45 ml) in the coating solution. As a result, the water contact angle of the modified surface was recorded as 155 ± 3°, which is higher than that of the pristine surface. The high contact angle is advantageous for reducing the wetting of the membrane. Additional mass transfer resistance was introduced by the superhydrophobic layer. In addition, continuous CO2 absorption tests were carried out in original and modified PVDF hollow fibre membrane contactors, using monoethanolamine (MEA) solution as the absorbent. A long-term stability test revealed that the modified PVDF hollow fibre membrane contactor was able to outperform the original membrane contactor and demonstrated outstanding long-term stability, suggesting that spray deposition is a promising approach to obtain superhydrophobic PVDF membranes for liquid–gas membrane absorption. PMID:29291117

  3. Developmentally regulated GTP-binding protein 2 is required for stabilization of Rac1-positive membrane tubules.

    Science.gov (United States)

    Mani, Muralidharan; Lee, Unn Hwa; Yoon, Nal Ae; Yoon, Eun Hye; Lee, Byung Ju; Cho, Wha Ja; Park, Jeong Woo

    2017-11-04

    Previously we have reported that developmentally regulated GTP-binding protein 2 (DRG2) localizes on Rab5 endosomes and plays an important role in transferrin (Tfn) recycling. We here identified DRG2 as a key regulator of membrane tubule stability. At 30 min after Tfn treatment, DRG2 localized to membrane tubules which were enriched with phosphatidylinositol 4-monophosphate [PI(4)P] and did not contain Rab5. DRG2 interacted with Rac1 more strongly with GTP-bound Rac1 and tubular localization of DRG2 depended on Rac1 activity. DRG2 depletion led to destabilization of membrane tubules, while ectopic expression of DRG2 rescued the stability of the membrane tubules in DRG2-depleted cells. Our results reveal a novel mechanism for regulation of membrane tubule stability mediated by DRG2. Copyright © 2017 Elsevier Inc. All rights reserved.

  4. Hydrogen bond stabilities in membrane-reconstituted alamethicin from amide-resolved hydrogen-exchange measurements.

    Science.gov (United States)

    Dempsey, C E; Handcock, L J

    1996-01-01

    Amide-resolved hydrogen-deuterium exchange-rate constants were measured for backbone amides of alamethicin reconstituted in dioleoylphosphatidylcholine vesicles by an exchange-trapping method combined with high-resolution nuclear magnetic resonance spectroscopy. In vesicles containing alamethicin at molar ratios between 1:20 and 1:100 relative to lipid, the exchange-rate constants increased with increasing volume of the D20 buffer in which the vesicles were suspended, indicating that exchange under these conditions is dominated by partitioning of the peptide into the aqueous phase. This was supported by observation of a linear relationship between the exchange-rate constants for amides in membrane-reconstituted alamethicin and those for amides in alamethicin dissolved directly into D2O buffer. Significant protection of amides from exchange with D2O buffer in membrane-reconstituted alamethicin is interpreted in terms of stabilization by helical hydrogen bonding. Under conditions in which amide exchange occurred by partitioning of the peptide into solution, only lower limits for hydrogen-bond stabilities in the membrane were determined; all the potentially hydrogen-bonded amides of alamethicin are at least 1000-fold exchange protected in the membrane-bound state. When partitioning of alamethicin into the aqueous phase was suppressed by hydration of reconstituted vesicles in a limiting volume of water [D2O:dioleoylphosphatidylcholine:alamethicin; 220:1:0.05; (M:M:M)], the exchange-protection factors exhibited helical periodicity with highly exchange-protected, and less well-protected, amides on the nonpolar and polar helix faces, respectively. The exchange data indicate that, under the conditions studied, alamethicin adopts a stable helical structure in DOPC bilayers in which all the potentially hydrogen-bonded amides are stabilized by helical hydrogen bonds. The protection factors define the orientation of the peptide helix with respect to an aqueous phase, which is

  5. Anti-inflammatory, membrane-stabilizing interactions of salmeterol with human neutrophils in vitro.

    Science.gov (United States)

    Anderson, R; Feldman, C; Theron, A J; Ramafi, G; Cole, P J; Wilson, R

    1996-04-01

    1. We have investigated the effects of salmeterol (0.3-50 microM) on several pro-inflammatory activities of human neutrophils in vitro. 2. Oxidant production by FMLP- and calcium ionophore (A23187)-activated neutrophils was particularly sensitive to inhibition by low concentrations (0.3-3 microM) of salmeterol, while the responses of phorbol myristate acetate- and opsonised zymosan-stimulated cells were affected only by higher concentrations (3-50 microM) of the drug. At these concentrations salmeterol is not cytotoxic, nor does it act as a scavenger of superoxide. 3. These anti-oxidative interactions of salmeterol with neutrophils were insensitive to propranolol but could be eliminated by washing the cells, or by pretreatment with low concentrations (1-2 microM) of the pro-oxidative, membrane-destabilizing phospholipids, lysophosphatidylcholine (LPC), platelet activating factor (PAF) and lysoPAF (LPAF). 4. At concentrations of 6.25-50 microM salmeterol interfered with several other activities of stimulated neutrophils, including intracellular calcium fluxes, phospholipase A2 activity and synthesis of PAF. 5. In an assay of membrane-stabilizing activity, salmeterol (25 and 50 microM) neutralized the haemolytic action of LPC, PAF and LPAF. 6. Of the other commonly used beta 2-adrenoceptor agonists, fenoterol, and formoterol, but not salbutamol, caused moderate inhibition of neutrophil oxidant generation by a superoxide-scavenging mechanism. However, unlike salmeterol, these agents possessed only weak membrane stabilizing properties. 7. We conclude that salmeterol antagonizes the pro-inflammatory, pro-oxidative activity of several bioactive lipids implicated in the pathogenesis of bronchial asthma, by a mechanism related to the membrane-stabilizing, rather than to the beta 2-agonist properties of this agent.

  6. Hydrogen bond stabilities in membrane-reconstituted alamethicin from amide-resolved hydrogen-exchange measurements.

    Science.gov (United States)

    Dempsey, C E; Handcock, L J

    1996-04-01

    Amide-resolved hydrogen-deuterium exchange-rate constants were measured for backbone amides of alamethicin reconstituted in dioleoylphosphatidylcholine vesicles by an exchange-trapping method combined with high-resolution nuclear magnetic resonance spectroscopy. In vesicles containing alamethicin at molar ratios between 1:20 and 1:100 relative to lipid, the exchange-rate constants increased with increasing volume of the D20 buffer in which the vesicles were suspended, indicating that exchange under these conditions is dominated by partitioning of the peptide into the aqueous phase. This was supported by observation of a linear relationship between the exchange-rate constants for amides in membrane-reconstituted alamethicin and those for amides in alamethicin dissolved directly into D2O buffer. Significant protection of amides from exchange with D2O buffer in membrane-reconstituted alamethicin is interpreted in terms of stabilization by helical hydrogen bonding. Under conditions in which amide exchange occurred by partitioning of the peptide into solution, only lower limits for hydrogen-bond stabilities in the membrane were determined; all the potentially hydrogen-bonded amides of alamethicin are at least 1000-fold exchange protected in the membrane-bound state. When partitioning of alamethicin into the aqueous phase was suppressed by hydration of reconstituted vesicles in a limiting volume of water [D2O:dioleoylphosphatidylcholine:alamethicin; 220:1:0.05; (M:M:M)], the exchange-protection factors exhibited helical periodicity with highly exchange-protected, and less well-protected, amides on the nonpolar and polar helix faces, respectively. The exchange data indicate that, under the conditions studied, alamethicin adopts a stable helical structure in DOPC bilayers in which all the potentially hydrogen-bonded amides are stabilized by helical hydrogen bonds. The protection factors define the orientation of the peptide helix with respect to an aqueous phase, which is

  7. Comparison of Theoretical and Experimental Mass Transfer Coefficients of Gases in Supported Ionic Liquid Membranes

    Czech Academy of Sciences Publication Activity Database

    Kárászová, Magda; Šimčík, Miroslav; Friess, K.; Randová, A.; Jansen, J. C.; Růžička, Marek; Sedláková, Zuzana; Izák, Pavel

    2013-01-01

    Roč. 118, 30 OCT (2013), s. 255-263 ISSN 1383-5866 R&D Projects: GA ČR GAP106/10/1194; GA MŠk(CZ) 7C11009 Grant - others:RFCS(XE) RFCR-CT-2010-00009; INP(IT) PON01_01840; HA MŠk(CZ) CZ.1.05/2.1.00/03.0071 Institutional support: RVO:67985858 Keywords : biogas purification * supported ionic liquid membranes * mass transfer coefficients Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 3.065, year: 2013

  8. Evaluation of the effects of enzyme-based liquid chemical stabilizers on subgrade soils

    CSIR Research Space (South Africa)

    Mgangira, Martin B

    2009-07-01

    Full Text Available The purpose of this study was to asses the strength of enzyme treated soil material. Thus the aim of the paper is to present laboratory results on the effects of two enzyme-based liquid chemicals as soil stabilizers. Soil samples were prepared...

  9. Correlation between local structure and stability of supercooled liquid state in Zr-based metallic glasses

    International Nuclear Information System (INIS)

    Saida, Junji; Imafuku, Muneyuki; Sato, Shigeo; Sanada, Takashi; Matsubara, Eiichiro; Inoue, Akihisa

    2007-01-01

    The correlation between the local structure and stability of supercooled liquid state is investigated in the Zr 70 (Ni, Cu) 30 binary and Zr 70 Al 10 (Ni, Cu) 20 (numbers indicate at.%) ternary metallic glasses. The Zr 70 Ni 30 binary amorphous alloy with a low stability of supercooled liquid state has a tetragonal Zr 2 Ni-like local structure around Ni atom. Meanwhile, the Zr 70 Cu 30 binary metallic glass has a different local structure of tetragonal Zr 2 Cu, where we suggest the icosahedral local structure by the quasicrystallization behavior in addition of a very small amount of noble metals. The effect of Al addition on the local structure in the Zr-Ni alloy is also examined. We have investigated that the dominant local structure changes in the icosahedral-like structure from the tetragonal Zr 2 Ni-like local structure by the Al substitution with Ni accompanying with the significant stabilization of supercooled liquid state. It is concluded that the formation of icosahedral local structure contributes to the enhancement of stability of supercooled liquid state in the Zr-based alloys

  10. Stabilization of thin liquid films by repulsive van der waals force

    KAUST Repository

    Li, Erqiang

    2014-05-13

    Using high-speed video recording of bubble rise experiments, we study the stability of thin liquid films trapped between a rising bubble and a surfactant-free liquid-liquid meniscus interface. Using different combinations of nonpolar oils and water that are all immiscible, we investigate the extent to which film stability can be predicted by attractive and repulsive van der Waals (vdW) interactions that are indicated by the relative magnitude of the refractive indices of the liquid combinations, for example, water (refractive index, n = 1.33), perfluorohexane (n = 1.23), and tetradecane (n = 1.43). We show that, when the film-forming phase was oil (perfluorohexane or tetradecane), the stability of the film could always be predicted from the sign of the vdW interaction, with a repulsive vdW force resulting in a stable film and an attractive vdW force resulting in film rupture. However, if aqueous electrolyte is the film-forming bulk phase between the rising air bubble and the upper oil phase, the film always ruptured, even when a repulsive vdW interaction was predicted. We interpret these results as supporting the hypothesis that a short-ranged hydrophobic attraction determines the stability of the thin water film formed between an air phase and a nonpolar oil phase. © 2014 American Chemical Society.

  11. Effect of liquid density differences on boiling two-phase flow stability

    International Nuclear Information System (INIS)

    Furuya, Masahiro; Manera, Annalisa; Bragt, David D.B.; Hagen, Tim H.J.J. van der; Kruijf, Willy J.M.de

    2002-01-01

    In order to investigate the effect of considering liquid density dependence on local fluid temperature in the thermal-hydraulic stability, a linear stability analysis is performed for a boiling natural circulation loop with an adiabatic riser. Type-I and Type-II instabilities were to investigate according to Fukuda-Kobori's classification. Type-I instability is dominant when the flow quality is low, while Type-II instability is relevant at high flow quality. Type-II instability is well known as the typical density wave oscillation. Neglecting liquid density differences yields estimates of Type-II instability margins that are too small, due to both a change in system-dynamics features and in the operational point. On the other hand, neglecting liquid density differences yields estimates of Type-I stability margins that are too large, especially due to a change in the operational point. Neglecting density differences is thus non-conservative in this case. Therefore, it is highly recommended to include liquid density dependence on the fluid subcooling in the stability analysis if a flow loop with an adiabatic rise is operated under the condition of low flow quality. (author)

  12. Development of Nanostructured Water Treatment Membranes Based on Thermotropic Liquid Crystals: Molecular Design of Sub-Nanoporous Materials.

    Science.gov (United States)

    Sakamoto, Takeshi; Ogawa, Takafumi; Nada, Hiroki; Nakatsuji, Koji; Mitani, Masato; Soberats, Bartolome; Kawata, Ken; Yoshio, Masafumi; Tomioka, Hiroki; Sasaki, Takao; Kimura, Masahiro; Henmi, Masahiro; Kato, Takashi

    2018-01-01

    Supply of safe fresh water is currently one of the most important global issues. Membranes technologies are essential to treat water efficiently with low costs and energy consumption. Here, the development of self-organized nanostructured water treatment membranes based on ionic liquid crystals composed of ammonium, imidazolium, and pyridinium moieties is reported. Membranes with preserved 1D or 3D self-organized sub-nanopores are obtained by photopolymerization of ionic columnar or bicontinuous cubic liquid crystals. These membranes show salt rejection ability, ion selectivity, and excellent water permeability. The relationships between the structures and the transport properties of water molecules and ionic solutes in the sub-nanopores in the membranes are examined by molecular dynamics simulations. The results suggest that the volume of vacant space in the nanochannel greatly affects the water and ion permeability.

  13. Formation and Properties of Poly(Ionic Liquid)-Carbene Nanogels Containing Individually Stabilized Silver Species.

    Science.gov (United States)

    Miao, Han; Schmidt, Johannes; Heil, Tobias; Antonietti, Markus; Willinger, Marc; Guterman, Ryan

    2018-03-06

    Imidazolium-based ionic liquids have the ability to undergo a variety of chemical reactions through an N-heterocyclic carbene (NHC) intermediate, which has expanded the chemical toolbox for new applications. Despite their uses and exploration, the carbene-forming properties and applications of their polymeric congeners, poly(ionic liquid)s (PILs), is still underdeveloped. In this work we explore the NHC-forming properties of a theophylline-derived PIL for nanogel synthesis. Using silver oxide as both the carbene forming reagent and crosslinker, nanogels containing individually stabilized ions can be created with different sizes and morphology, including large "galaxy-like" superstructures. Using high-resolution TEM techniques, we directly observed the sub-nanometer structure of these constructs. This features combined exemplifies the unique chemistry of poly-NHCs for single metal ion stabilization nanogel design. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Surface modification and characterization for dispersion stability of inorganic nanometer-scaled particles in liquid media

    International Nuclear Information System (INIS)

    Kamiya, Hidehiro; Iijima, Motoyuki

    2010-01-01

    Inorganic nanoparticles are indispensable for science and technology as materials, pigments and cosmetics products. Improving the dispersion stability of nanoparticles in various liquids is essential for those applications. In this review, we discuss why it is difficult to control the stability of nanoparticles in liquids. We also overview the role of surface interaction between nanoparticles in their dispersion and characterization, e.g. by colloid probe atomic force microscopy (CP-AFM). Two types of surface modification concepts, post-synthesis and in situ modification, were investigated in many previous studies. Here, we focus on post-synthesis modification using adsorption of various kinds of polymer dispersants and surfactants on the particle surface, as well as surface chemical reactions of silane coupling agents. We discuss CP-AFM as a technique to analyze the surface interaction between nanoparticles and the effect of surface modification on the nanoparticle dispersion in liquids. (topical review)

  15. Surface modification and characterization for dispersion stability of inorganic nanometer-scaled particles in liquid media

    Directory of Open Access Journals (Sweden)

    Hidehiro Kamiya and Motoyuki Iijima

    2010-01-01

    Full Text Available Inorganic nanoparticles are indispensable for science and technology as materials, pigments and cosmetics products. Improving the dispersion stability of nanoparticles in various liquids is essential for those applications. In this review, we discuss why it is difficult to control the stability of nanoparticles in liquids. We also overview the role of surface interaction between nanoparticles in their dispersion and characterization, e.g. by colloid probe atomic force microscopy (CP-AFM. Two types of surface modification concepts, post-synthesis and in situ modification, were investigated in many previous studies. Here, we focus on post-synthesis modification using adsorption of various kinds of polymer dispersants and surfactants on the particle surface, as well as surface chemical reactions of silane coupling agents. We discuss CP-AFM as a technique to analyze the surface interaction between nanoparticles and the effect of surface modification on the nanoparticle dispersion in liquids.

  16. Stability, Deactivation, and Regeneration of Chloroaluminate Ionic Liquid as Catalyst for Industrial C4 Alkylation

    Directory of Open Access Journals (Sweden)

    Xiang Li

    2017-12-01

    Full Text Available Alkylation of isobutane and 2-butene was carried out in a continuous unit using triethylamine hydrochloride (Et3NHCl-aluminum chloride (AlCl3 ionic liquid (IL as catalyst. The effects of impurities such as water, methanol, and diethyl ether on the stability of the catalytic properties and deactivation of the ionic liquid were studied in the continuous alkylation. In the Et3NHCl-2AlCl3 ionic liquid, only one half of the aluminum chloride could act as the active site. With a molar ratio of 1:1, the active aluminum chloride in the ionic liquid was deactivated by water by reaction or by diethyl ether through complexation while the complexation of aluminum chloride with two molecular proportions of methanol inactivated the active aluminum chloride in the ionic liquid. The deactivation of chloroaluminate ionic liquid was observed when the active aluminum chloride, i.e., one half of the total aluminum chloride in the ionic liquid, was consumed completely. The regeneration of the deactivated ionic liquid was also investigated and the catalytic activity could be recovered by means of replenishment with fresh aluminum chloride.

  17. Transport of Eu3+ through a Bis(2-ethylhexyl)-phosphoric acid, n-dodecane solid supported liquid membrane

    International Nuclear Information System (INIS)

    Danesi, P.R.; Horwitz, E.P.; Rickert, P.

    1982-01-01

    The coupled transpot of Eu 3 + and H + ions througn a solid supported liquid membrane consisting of a porous polypropylene film immobilizing an HDEHP solution in n-dodecane has been studied as a function of the membrane area, stirring speed of the aqueous solutions, membrane composition, and acidity of the feed solution. The experimental results are in agreement with predictions derived from a theoretical permeability coefficient equation which assumes that membrane diffusion and aqueous film diffusion are the only rate-controlling factors

  18. Influence of the intermediate layer on the hydrothermal stability of sol-gel derived hybrid silica membranes

    NARCIS (Netherlands)

    ten Hove, Marcel; Luiten-Olieman, Mieke W.J.; Huiskes, Cindy; Nijmeijer, Arian; Winnubst, Louis

    2017-01-01

    The hydrothermal stability of microporous silica hybrid sol-gel derived membranes is often only tested for either the mesoporous intermediate membrane layer or the microporous separation layer. In this work an investigation is done on the interaction between the intermediate γ-alumina layer and the

  19. Analysis of cerium-composite polymer-electrolyte membranes during and after accelerated oxidative-stability test

    Science.gov (United States)

    Shin, Dongwon; Han, Myungseong; Shul, Yong-Gun; Lee, Hyejin; Bae, Byungchan

    2018-02-01

    The oxidative stability of membranes constructed from a composite of pristine sulfonated poly(arylene ether sulfone) and cerium was investigated by conducting an accelerated oxidative-stability test at the open-circuit voltage (OCV). The membranes were analyzed in situ through OCV and impedance measurements, cyclic voltammetry, and linear-sweep voltammetry to monitor the electrochemical properties during the stability test. Although the high-frequency resistance of a composite membrane was slightly higher than that of a pristine membrane because of the exchange of protons from the sulfonic acid with cerium ions, the composite membrane maintained its potential for much longer than the pristine membrane. The effect of the cerium ions as radical scavengers was confirmed by analyzing the drain water and chemical structure after operation. These post-operation analyses confirmed that cerium ions improved the oxidative stability of the hydrocarbon-based polymer during fuel-cell operation. It is clear that the cerium-based radical scavengers prevented chemical degradation of the polymer membrane as well as the electrode in terms of hydrogen cross-over, polymer-chain scission, and the electrochemical surface area, while they rarely diffused outward from the membrane.

  20. An analysis of dynamic stability for a flexible rotor filled with liquid

    Science.gov (United States)

    Wang, Guangding; Yuan, Huiqun

    2018-03-01

    The investigation of dynamic stability for a flexible rotor completely filled with liquid is carried out. The perturbation differential equations of infinitesimal fluid are established on the basis of three-dimensional flow analysis in the rotor cavity. The analytical expression of the hydrodynamic force exerted on the rotor inner wall is obtained by using the Fourier series expansion. Assuming that both ends of the rotor are simply supported and the fluid motion is axially symmetric, the nondimensional whirling frequency equation of the system is derived. According to the obtained frequency equation, the system stability is analyzed and the results are compared with a rigid rotor system. Moreover, the effects of the mass ratio and system parameter on the stability of a flexible liquid-filled rotor system are discussed.

  1. Structure and Stability of the Spinach Aquaporin SoPIP2;1 in Detergent Micelles and Lipid Membranes

    DEFF Research Database (Denmark)

    Plasencia, Ines; Survery, Sabeen; Ibragimova, Sania

    2011-01-01

    reconstitution of the purified protein into biomimetic systems, we have here for the first time characterized the structural stability of SoPIP2;1. Methodology/Principal Finding: We have characterized the protein structural stability after purification and after reconstitution into detergent micelles......-helical in accordance with crystallographic data. The protein has a high thermal structural stability in detergent solutions, with an irreversible thermal unfolding occurring at a melting temperature of 58 degrees C. Incorporation of the protein into lipid membranes increases the structural stability as evidenced...... by an increased melting temperature of up to 70 degrees C. Conclusion/Significance: The results of this study provide insights into SoPIP2;1 stability in various host membranes and suggest suitable choices of detergent and lipid composition for reconstitution of SoPIP2;1 into biomimetic membranes...

  2. The stability of the dome of a liquid bubble rising in a dense liquid

    Science.gov (United States)

    Kanygin, R. I.; Kascheev, A. D.; Kudryavtsev, A. Yu; Meshkov, E. E.; Novikova, I. A.

    2018-02-01

    The results of experiments researching the stability of the dome of a large water bubble rising in a salt solution are presented. The experiments demonstrate the suppression of the Rayleigh-Taylor instability on the dome of the rising bubble with the Atwood number being A ≪ 1. The intensive development of the Kelvin-Helmholtz instability on the lateral surface of the bubble is observed as it rises. The stability of the dome of the rising bubble is explained by the action of an accelerated shear flow of water over the bubble surface. The results of computational modeling of the problem by the STAR-CCM + program are presented.

  3. Conditions that Stabilize Membrane Domains Also Antagonize n-Alcohol Anesthesia

    Science.gov (United States)

    Machta, Benjamin B.; Gray, Ellyn; Nouri, Mariam; McCarthy, Nicola L. C.; Gray, Erin M.; Miller, Ann L.; Brooks, Nicholas J.; Veatch, Sarah L.

    2016-08-01

    Diverse molecules induce general anesthesia with potency strongly correlated both with their hydrophobicity and their effects on certain ion channels. We recently observed that several n-alcohol anesthetics inhibit heterogeneity in plasma membrane derived vesicles by lowering the critical temperature ($T_c$) for phase separation. Here we exploit conditions that stabilize membrane heterogeneity to further test the correlation between the anesthetic potency of n-alcohols and effects on $T_c$. First we show that hexadecanol acts oppositely to n-alcohol anesthetics on membrane mixing and antagonizes ethanol induced anesthesia in a tadpole behavioral assay. Second, we show that two previously described `intoxication reversers' raise $T_c$ and counter ethanol's effects in vesicles, mimicking the findings of previous electrophysiological and behavioral measurements. Third, we find that hydrostatic pressure, long known to reverse anesthesia, also raises $T_c$ in vesicles with a magnitude that counters the effect of butanol at relevant concentrations and pressures. Taken together, these results demonstrate that $\\Delta T_c$ predicts anesthetic potency for n-alcohols better than hydrophobicity in a range of contexts, supporting a mechanistic role for membrane heterogeneity in general anesthesia.

  4. Study on Mg2+ removal from ammonium dihydrogen phosphate solution by an emulsion liquid membrane

    Directory of Open Access Journals (Sweden)

    Luo JianHong

    2014-01-01

    Full Text Available Mg2+is extracted from ammonium dihydrogen phosphate (NH4H2PO4 solution by an emulsion liquid membrane (ELM using mono-(2-ethylhexyl 2-ethylhexyl phosphonate (HEHPEHEas a carrier, sulfonated liquid polybutadiene (LYF as a surfactant and kerosene as a solvent. To study the extraction efficiency and advantages of the ELM process in the separation of Mg2+,the effects of various operating conditions on the extraction -HEHPEHE volume fraction, reaction temperature, treat ratio (emulsion phase / external phase, phase ratio (membrane phase / internal phase, agitation speed, extraction time, internal phase concentration, surfactant LYF concentration and initial pH of NH4H2PO4 solution are experimentally investigated and discussed. The results show that Mg2+ in NH4H2PO4 solution can be effectively removed by the ELM process. An extraction efficiency of more than 83.1% is attained at the optimized parameters and superior-grade NH4H2PO4can be obtained by two levels of extraction.

  5. In-situ Non-Invasive Imaging of Liquid-Immersed Thin Film Composite Membranes

    KAUST Repository

    Ogieglo, Wojciech

    2017-10-14

    We present a non-invasive method to directly image liquid-immersed thin film composite membranes. The approach allows accessing information not only on the lateral distribution of the coating thickness, including variations in its swelling and density, but also on the distribution of substrate porosity, roughness, accessibility of pores to liquid, and even the degree of pore intrusion related to the thin layer deposition process. The method can be particularly helpful in the fields of functional coatings or membranes to allow laterally-resolved studies under realistic application conditions thereby opening completely new research avenues. The approach is demonstrated in a study of two polymers of intrinsic microporosity, PIM-1 and PIM-6FDA-OH, coated on polyacrylonitrile support and immersed in water. Variations of the skin morphology using different coating methods (floating, spin-coating and dip-coating) are evaluated with the help of the presented method. Surfaces of at least tens of cm2 can be potentially analyzed.

  6. Continued Advancement of Supported Liquid Membranes for Carbon Dioxide Control in Extravehicular Activity Applications

    Science.gov (United States)

    Wickham, David T.; Gleason, Kevin J.; Engel, Jeffrey R.; Cowley, Scott W.; Chullen, Cinda

    2015-01-01

    The Development of a new, robust, portable life support system (PLSS) is currently a high NASA priority in order to support longer and safer extravehicular activity (EVA) missions that will be necessary as space travel extends to near-Earth asteroids and eventually Mars. One of the critical PLSS functions is maintaining the carbon dioxide (CO2) concentration in the suit at acceptable levels. The Metal Oxide (MetOx) canister has a finite CO2 adsorption capacity and therefore in order to extend mission times, the unit would have to be larger and heavier, which is undesirable; therefore new CO2 control technologies must be developed. While recent work has centered on the use of alternating sorbent beds that can be regenerated during the EVA, this strategy increases the system complexity and power consumption. A simpler approach is to use a membrane that vents CO2 to space but retains oxygen(O2). A membrane has many advantages over current technology: it is a continuous system with no theoretical capacity limit, it requires no consumables, and it requires no hardware for switching beds between absorption and regeneration. Conventional gas separation membranes do not have adequate selectivity for use in the PLSS, but the required performance could be obtained with a supported liquid membrane (SLM), which consists of a microporous film filled with a liquid that selectively reacts with CO2 over oxygen (O2). In a recently completed Phase II Small Business Innovative Research project, Reaction Systems developed a new reactive liquid that has effectively zero vapor pressure, making it an ideal candidate for use in an SLM. Results obtained with the SLM in a flat sheet configuration with representative pressures of CO2, O2, and water (H2O) have shown that the CO2 permeation rate and CO2/O2 selectivity requirements have been met. In addition, the SLM vents moisture to space very effectively. The SLM has also been prepared and tested in a hollow fiber form, which will be

  7. Novel macrocyclic carriers for proton-coupled liquid membrane transport. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Lamb, J.D.; Izatt, R.M.; Bradshaw, J.S.; Shirts, R.B.

    1996-08-24

    The objective of this research program is to elucidate the chemical principles which are responsible for the cation selectivity and permeability of liquid membranes containing macrocyclic carriers. Several new macrocyclic carriers were synthesized during the last three year period. In addition, new, more convenient synthetic routes were achieved for several nitrogen-containing bicyclic and tricyclic macrocycles. The cation binding properties of these macrocycles were investigated by potentiometric titration, calorimetric titration, solvent extraction and NMR techniques. In addition, hydrophobic macrocycles were incorporated into dual hollow fiber and other membrane systems to investigate their membrane performance, especially in the proton-coupled transport mode. A study of the effect of methoxyalkyl macrocycle substituents on metal ion transport was completed. A new calorimeter was constructed which made it possible to study the thermodynamics of macrocycle-cation binding to very high temperatures. Measurements of thermodynamic data for the interaction of crown ethers with alkali and alkaline earth cations were achieved to 473 K. Molecular modeling work was begun for the first time on this project and fundamental principles were identified and developed for the establishment of working models in the future.

  8. Inclusion separation of alkali metals in emulsion liquid membranes by nanobaskets of calix[4]crown-3

    Directory of Open Access Journals (Sweden)

    B. Mokhtari

    2012-12-01

    Full Text Available Nano-assisted inclusion separation of alkali metals from basic solutions was reported by an inclusion-facilitated emulsion liquid membrane process. The novelty of this study is application of nanobaskets of calixcrown in the selective and efficient separation of alkali metals as both the carrier and the surfactant. For this purpose, two diacids, p-tert-butylcalix[4]arene-1,2-crown-3 in the cone and the 1,2alternate conformation, as well as another diacid, p-tert-butylcalix[4]arene-1,2-thiacrown-3 in the cone conformation, were synthesized. Their inclusion-extraction parameters were optimized, including the calixcrown scaffold (04, 4 wt% as the carrier/demulsifier, commercial kerosene as the diluent in the membrane, sulphonic acid (0.2 M and ammonium carbonate (0.4 M as the strip and the feed phases; the phase and the treat ratios were 0.8 and 0.3, mixing speed (300 rpm, and initial solute concentration (100 mg/L. The selectivity of the membrane was examined for more than ten interfering cations was examined and the results reveled that, under the optimized operating condition, the degree of inclusion-extraction of alkali metals was as high as 98-99%.

  9. Factors affecting the stability and performance of ionic liquid-based planar transient photodetectors.

    Science.gov (United States)

    Dalgleish, Simon; Reissig, Louisa; Hu, Laigui; Matsushita, Michio M; Sudo, Yuki; Awaga, Kunio

    2015-05-12

    A novel planar architecture has been developed for the study of photodetectors utilizing the transient photocurrent response induced by a metal/insulator/semiconductor/metal (MISM) structured device, where the insulator is an ionic liquid (IL-MISM). Using vanadyl 2,3-naphthalocyanine, which absorbs in the communications-relevant near-infrared wavelength region (λ(max,film) ≈ 850 nm), in conjunction with C60 as a bulk heterojunction, the high capacitance of the formed electric double layers at the ionic liquid interfaces yields high charge separation efficiency within the semiconductor layer, and the minimal potential drop in the bulk ionic liquid allows the electrodes to be offset by distances of over 7 mm. Furthermore, the decrease in operational speed with increased electrode separation is beneficial for a clear modeling of the waveform of the photocurrent signal, free from the influence of measurement circuitry. Despite the use of a molecular semiconductor as the active layer in conjunction with a liquid insulating layer, devices with a stability of several days could be achieved, and the operational stability of such devices was shown to be dependent solely on the solubility of the active layer in the ionic liquid, even under atmospheric conditions. Furthermore, the greatly simplified device construction process, which does not rely on transparent electrode materials or direct electrode deposition, provides a highly reproducible platform for the study of the electronic processes within IL-MISM detectors that is largely free from architectural constraints.

  10. Stability limits for the supercooled liquid and superheated crystal of Lennard-Jones particles.

    Science.gov (United States)

    Loscar, Ernesto S; Martin, Daniel A; Grigera, Tomás S

    2017-07-21

    We have studied the limits of stability in the first order liquid-solid phase transition in a Lennard-Jones system by means of the short-time relaxation method and using the bond-orientational order parameter Q 6 . These limits are compared with the melting line. We have paid special attention to the supercooled liquid, comparing our results with the point where the free energy cost of forming a nucleating droplet goes to zero. We also indirectly estimate the dimension associated to the critical nucleus at the spinodal, expected to be fractal according to mean field theories of nucleation.

  11. The effects of a protein osmolyte on the stability of the integral membrane protein glycerol facilitator.

    Science.gov (United States)

    Baturin, Simon; Galka, Jamie J; Piyadasa, Hadeesha; Gajjeraman, S; O'Neil, Joe D

    2014-12-01

    Osmolytes are naturally occurring molecules used by a wide variety of organisms to stabilize proteins under extreme conditions of temperature, salinity, hydrostatic pressure, denaturant concentration, and desiccation. The effects of the osmolyte trimethylamine N-oxide (TMAO) as well as the influence of detergent head group and acyl chain length on the stability of the Escherichia coli integral membrane protein glycerol facilitator (GF) tetramer to thermal and chemical denaturation by sodium dodecyl sulphate (SDS) are reported. TMAO promotes the association of the normally tetrameric α-helical protein into higher order oligomers in dodecyl-maltoside (DDM), but not in tetradecyl-maltoside (TDM), lyso-lauroylphosphatidyl choline (LLPC), or lyso-myristoylphosphatidyl choline (LMPC), as determined by dynamic light scattering (DLS); an octameric complex is particularly stable as indicated by SDS polyacrylamide gel electrophoresis. TMAO increases the heat stability of the GF tetramer an average of 10 °C in the 4 detergents and also protects the protein from denaturation by SDS. However, it did not promote re-association to the tetramer when added to SDS-dissociated protein. TMAO also promotes the formation of rod-like detergent micelles, and DLS was found to be useful for monitoring the structure of the protein and the redistribution of detergent during thermal dissociation of the protein. The protein is more thermally stable in detergents with the phosphatidylcholine head group (LLPC and LMPC) than in the maltoside detergents. The implications of the results for osmolyte mechanism, membrane protein stability, and protein-protein interactions are discussed.

  12. High-Permeance Room-Temperature Ionic-Liquid-Based Membranes for CO2/N-2 Separation

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, JS; Mok, MM; Cowan, MG; McDanel, WM; Carlisle, TK; Gin, DL; Noble, RD

    2014-12-24

    We have developed and fabricated thin-film composite (TFC) membranes with an active layer consisting of a room-temperature ionic liquid/polymerized (room-temperature ionic liquid) [i.e., (RTIL)/poly(RTIL)] composite material. The resulting membrane has a CO2 permeance of 6100 +/- 400 GPU (where 1 GPU = 10(-6) cm(3)/(cm(2) s cmHg)) and an ideal CO2/N-2 selectivity of 22 +/- 2. This represents a new membrane with state-of-the-art CO2 permeance and good CO2/N-2 selectivity. To our knowledge, this is the first example of a TFC gas separation membrane composed of an RTIL-containing active layer.

  13. Poly(vinylbenzylchloride) Based Anion-Exchange Blend Membranes (AEBMs): Influence of PEG Additive on Conductivity and Stability.

    Science.gov (United States)

    Kerres, Jochen A; Krieg, Henning M

    2017-06-16

    In view of the many possible applications such as fuel cells and electrolysers, recent interest in novel anion exchange membranes (AEMs) has increased significantly. However, their low conductivity and chemical stability limits their current suitability. In this study, the synthesis and characterization of several three- and four-component anion exchange blend membranes (AEBMs) is described, where the compositions have been systematically varied to study the influence of the AEBM's composition on the anion conductivities as well as chemical and thermal stabilities under strongly alkaline conditions. It was shown that the epoxide-functionalized poly(ethylene glycol)s that were introduced into the four-component AEBMs resulted in increased conductivity as well as a marked improvement in the stability of the AEBMs in an alkaline environment. In addition, the thermal stability of the novel AEBMs was excellent showing the suitability of these membranes for several electrochemical applications.

  14. Hydrodynamic stability of thermoviscous liquid film inside a rotating horizontal cylinder: Heating and cooling effects

    Science.gov (United States)

    Kumawat, Tara Chand; Tiwari, Naveen

    2018-03-01

    Steady two-dimensional solutions and their stability analysis are presented for thin film of a thermoviscous liquid flowing inside a cylinder rotating about its horizontal axis. The inner surface of the cylinder is either uniformly hotter or colder than the enveloping air. The mass, momentum, and energy equations are simplified using thin-film approximation. The analytically obtained film thickness evolution equation consists of various dimensionless parameters such as gravitational number, Bond number, Biot number, thermoviscosity number, and Marangoni number. The viscosity of the liquid is considered as an exponential function of temperature. The viscosity increases (decreases) within the film thickness away from the inner surface of the cylinder when the surface is uniformly hotter (colder) than the atmosphere. For hotter (colder) surface, the film thickness on the rising side decreases (increases) when convective heat transfer at the free surface is increased. The surface tension gradient at the free surface generates Marangoni stress that has a destabilizing (stabilizing) effect on the thin film flow in the case of a hotter (colder) cylinder. The thermoviscosity number stabilizes (destabilizes) the flow on a heating (cooling) surface and this effect increases with an increase in the heat transfer at the free surface. For a hotter surface and in the presence of Marangoni stress, the convective heat transfer at the interface has the destabilizing effect for small values of the Biot number and assumes a stabilizing role for larger values. Non-linear simulations show consistency with the linear stability analysis.

  15. Study of the extraction and the purification of americium and trivalent actinides contained in effluents with supported liquid membranes

    International Nuclear Information System (INIS)

    Guillou, P.

    1990-12-01

    The supported liquid membrane technique is studied and developed for americium recovery from uranium or plutonium matrices and decontamination of liquid radioactive wastes. First tests on uranium-nickel solutions with a flat membrane showed the easiness of the operation and the efficiency of the process. Acid-resistant (10 N), interchangeable elements with hollow fibers, are developed and also a computerized automatic device. The different tests on americium solutions demonstrate the feasibility and the reliability of the system. Influence of various parameters on transfer kinetics is investigated

  16. Evaluation of different organophosphorous extractants for uranium permeation from nitric acid medium across a supported liquid membrane

    International Nuclear Information System (INIS)

    Sujoy, Biswas; Roy, S.B.; Pal, Sangita; Tewari, P.K.; Pathak, P.N.; Manchanda, V.K.

    2011-01-01

    Uranium permeation studies from nitric acid medium across a supported liquid membrane were carried out employing different acidic organophosphorous extractants viz. Cyanex 272, PC88A, DNPPA either alone or in combination with neutral donors such as TBP, TEHP, TOPO, and Cyanex 923. H 2 SO 4 solution was used as a receiver phase. Effect of various parameters like effect of various acidic extractants, presence of neutral donors as well as nature of receiver phase on uranium transport across supported liquid membrane were investigated. (author)

  17. NUMERICAL SOLUTION OF THE PROBLEM ON STABILITY OF A LIQUID BRIDGE BETWEEN TWO COAXIAL CYLINDERS

    Directory of Open Access Journals (Sweden)

    Yu. N. Gorbacheva

    2013-01-01

    Full Text Available The problem on equilibrium shapes and stability of axially symmetric liquid bridge between the end faces of two coaxial vertical cylinders of equal radius in gravitational field is considered. A scheme of spline type for numerical solving of the problem is developed. Construction of the scheme is based on an approximation of the free surface by parametric cubic splines which exactly satisfy equations of the differential problem at grid nodes. Equilibrium free-surface shapes in a wide range of problem parameters are obtained. Critical values of the bridge height corresponding to the loss of equilibrium stability depending on the Bond number are determined.

  18. Hybrid biofilm-membrane bioreactor (Bf-MBR) for minimization of bulk liquid-phase organic substances and its positive effect on membrane permeability.

    Science.gov (United States)

    Sun, F Y; Li, P; Li, J; Li, H J; Ou, Q M; Sun, T T; Dong, Z J

    2015-12-01

    Four biofilm membrane bioreactors (Bf-MBRs) with various fixed carrier volumes (C:M) were operated in parallel to investigate the effect of attached-growth mode biomass involvement to the change of liquid-phase organics characteristics and membrane permeability, by comparing with conventional MBR. The experiments displayed that C:M and co-existence of biofilm with suspended solids in Bf-MBRs resulted in slight difference in pollutants removal effectiveness, and in rather distinct biomass properties and bacterial activities. The membrane permeability and specific resistance of bulk suspension of Bf-MBRs related closely with the liquid-phase organic substance, including soluble microbial products (SMP) and biopolymer cluster (BPC). Compared with conventional MBR, Bf-MBR with proper C:M had a low total biomass content and food-chain, where biofilm formation and its dominance affected liquid-phase organics, especially through reducing their content and minimizing strongly and weakly hydrophobic components with small molecular weight, and thus to mitigate membrane fouling significantly. Copyright © 2015 Elsevier Ltd. All rights reserved.

  19. Interfacial transport phenomena and stability in liquid-metal/water systems: scaling considerations

    International Nuclear Information System (INIS)

    Abdulla, S.; Liu, X.; Anderson, M.; Bonazza, R.; Corradini, M.; Cho, D.

    2001-01-01

    One concept being considered for steam generation in innovative nuclear reactor applications, involves water coming into direct contact with a circulating molten metal. The vigorous agitation of the two fluids, the direct liquid-liquid contact and the consequent large interfacial area give rise to very high heat transfer coefficients and rapid steam generation. For an optimum design of such direct contact heat exchange and vaporization systems, detailed knowledge is necessary of the various flow regimes, interfacial transport phenomena, heat transfer and operational stability. In this paper we describe current results from the first year of this research that studies the transport phenomena involved with the injection of water into molten metals (e.g., lead alloys). In particular, this work discusses scaling considerations related to direct contact heat exchange, our experimental plans for investigation and a test plan for the important experimental parameters; i.e., the water and liquid metal mass flow rates, the liquid metal pool temperature and the ambient pressure of the direct contact heat exchanger. Past experimental work and initial scaling results suggest that our experiments can directly represent the proper liquid metal pool temperature and the water subcooling. The experimental variation in water and liquid metal flow rates and system pressure (1-10 bar), although smaller than the current conceptual system designs, is sufficient to verify the expected scale effects to demonstrate the phenomena. (authors)

  20. Synthesis of mesh-shaped calcia partially stabilized zirconia using eggshell membrane template as filler composite

    Directory of Open Access Journals (Sweden)

    Gema Gempita

    2017-08-01

    Full Text Available This experiment was conducted experimentally to synthesize Calcia Partially Stabilized Zirconia (Ca-PSZ by sol-gel method using eggshell membrane template as a composite filler. The eggshell membrane was used to produce a mesh shaped structure, which hopefully can improve the mechanical properties of the composite. Ca-PSZ filler was synthesized from ZrOCl2 precursor and Ca(NO32 stabilizer with a 24 hours immersion time. Ca-PSZ of synthesis then mixed with the resin matrix to test its composite hardness. The EDS characterization results suggested that the sample contained elements of zirconia, calcium, and oxygen. Whereas, the XRD characterization identified that crystal structures that formed in the sample were nano scale tetragonal. Characterization of SEM showed Ca-PSZ with mesh structured. The average composite hardness value was 15.79 VHN. The composites with Ca-PSZ-synthesized filler could be prepared and its hardness value was higher than the composite with Ca-PSZ filler in spherical particles, but the hardness was still below the composite on the market.

  1. Membrane permeation of testosterone from either solutions, particle dispersions, or particle-stabilized emulsions.

    Science.gov (United States)

    Binks, Bernard P; Fletcher, Paul D I; Johnson, Andrew J; Elliott, Russell P

    2012-02-07

    We derive a unified model that accounts for the variation in extent and rate of membrane permeation by a permeating species with the type of donor compartment formulation (aqueous and oil solutions, particle dispersions, and oil-in-water and water-in-oil emulsions stabilized by particles) initially containing the permeant. The model is also applicable to either closed-loop or open-flow configurations of the receiver compartment of the permeation cell. Predictions of the model are compared with measured extents and rates of permeation of testosterone across an 80 μm thick polydimethylsiloxane (PDMS) membrane from donor compartments initially containing testosterone dissolved in either aqueous or isopropylmyristate (IPM) solutions, aqueous or IPM dispersions of silica nanoparticles or IPM-in-water or water-in-IPM emulsions stabilized by silica nanoparticles. Using a single set of input parameters, the model successfully accounts for the wide variations in permeation behavior observed for the different donor formulation types with either closed-loop or open flow configurations of the permeation cell receiver compartment.

  2. Induction of cassava somatic embryogenesis in liquid medium associated to floating membrane rafts

    Directory of Open Access Journals (Sweden)

    Elizabete Keiko Takahashi

    2000-01-01

    Full Text Available The objective of this study was to examine the effect of two culture systems, liquid medium associated to floating membranes and solid medium, both supplemented with different concentrations of 2,4-D, in the induction of somatic embryogenesis of cassava (Manihot esculenta Crantz. Only 28% of the young leaf lobes (with 9 µM 2,4-D were induced to form organized embryogenic structures (OES with membrane rafts, compared to 50% of the explants presenting this type of tissue in solid medium with 36 µM of 2,4-D. Despite the lower response observed in liquid medium with membrane, the amount of OES/explant in all 2,4-D concentrations was higher than solid medium. Based on the results and considering the high cost of the membrane rafts, this system was not distinctly superior than solid medium for inducing somatic embryogenesis in cassava.O objetivo deste estudo foi comparar a indução de embriogênese somática em mandioca (Manihot esculenta Crantz utilizando o sistema de cultivo em meio líquido associado com membranas flutuantes com meio sólido, ambos suplementados com diferentes doses de 2,4-D. Utilizando membranas flutuantes, o melhor resultado foi obtido na concentração de 9 µM 2,4-D, onde apenas 28% dos explantes foliares apresentaram estruturas embriogênicas organizadas (OES. Por outro lado, em explantes cultivados em meio sólido suplementado com 36 µM de 2,4-D a frequência de OES foi de 50%. Embora a frequência de indução embriogênica tenha sido inferior em meio líquido associado com membranas flutuantes, a quantidade de OES por explante foi igual ou superior ao do meio sólido em todas as concentrações de 2,4-D testadas. Baseado nestes resultados, e considerando o elevado custo das membranas, este sistema de cultura não apresentou vantagens significativas para indução de embriogênese somática em mandioca em relação ao meio sólido.

  3. Shape control of surface-stabilized disclination loops in nematic liquid crystals

    Science.gov (United States)

    Sunami, Kanta; Imamura, Koki; Ouchi, Tomohiro; Yoshida, Hiroyuki; Ozaki, Masanori

    2018-02-01

    Recent studies on topological defects in conventional and active nematic liquid crystals have revealed their potential as sources of advanced functionality whereby the collective behavior of the constituent molecules or cells is controlled. On the other hand, the fact that they have high energies and are metastable makes their shape control a nontrivial issue. Here, we demonstrate stabilization of arbitrary-shaped closed disclination loops with 1/2 strength floating in the bulk by designing the twist angle distribution in a liquid crystal cell. Continuous variation of the twist angle from below to above |π /2 | allows us to unambiguously position reverse twist disclinations at will. We also analyze the elastic free energy and uncover the relationship between the twist angle pattern and shrink rate of the surface-stabilized disclination loop.

  4. Review of Potential Candidate Stabilization Technologies for Liquid and Solid Secondary Waste Streams

    Energy Technology Data Exchange (ETDEWEB)

    Pierce, Eric M.; Mattigod, Shas V.; Westsik, Joseph H.; Serne, R. Jeffrey; Icenhower, Jonathan P.; Scheele, Randall D.; Um, Wooyong; Qafoku, Nikolla

    2010-01-30

    Pacific Northwest National Laboratory has initiated a waste form testing program to support the long-term durability evaluation of a waste form for secondary wastes generated from the treatment and immobilization of Hanford radioactive tank wastes. The purpose of the work discussed in this report is to identify candidate stabilization technologies and getters that have the potential to successfully treat the secondary waste stream liquid effluent, mainly from off-gas scrubbers and spent solids, produced by the Hanford Tank Waste Treatment and Immobilization Plant (WTP). Down-selection to the most promising stabilization processes/waste forms is needed to support the design of a solidification treatment unit (STU) to be added to the Effluent Treatment Facility (ETF). To support key decision processes, an initial screening of the secondary liquid waste forms must be completed by February 2010.

  5. Stability, Molecular Sieving, and Ion Diffusion Selectivity of a Lamellar Membrane from Two-Dimensional Molybdenum Disulfide.

    Science.gov (United States)

    Deng, Mengmeng; Kwac, Kijeong; Li, Meng; Jung, Yousung; Park, Hyung Gyu

    2017-04-12

    Two-dimensional (2D) subnanometer channels allow unique mass transport promising for molecular sieving. New 2D channels of MoS 2 nanosheets allow one to understand molecular transmission and separation, unlike the graphene oxide counterpart containing various defects and cationic metal contaminants. Membranes from layered MoS 2 platelets show extraordinary stability in an aqueous environment and compatibility with polymer filters, both beneficial to efficient manufacturing. Sharing gas-tightness and unimpeded water vapor permeation with a graphene oxide membrane, our lamellar MoS 2 membrane demonstrates a molecular sieving property for organic vapor for the first time. The MoS 2 membrane also reveals diffusion selectivity of aqueous ions, attributable to the energy penalty in bulk-to-2D dimensional transition. These newly revealed properties of the lamellar membrane full of angstrom-sized 2D channels point to membrane technology applications for energy and environment.

  6. Standard Test Method for Preparing Aircraft Cleaning Compounds, Liquid Type, Water Base, for Storage Stability Testing

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2002-01-01

    1.1 This test method covers the determination of the stability in storage, of liquid, water-base chemical cleaning compounds, used to clean the exterior surfaces of aircraft. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  7. CONCERNS OF CONTEMPORARY DISINFECTION: CHLORINE OR STABILIZED LIQUID SOLUTION OF CHLORINE DIOXIDE

    OpenAIRE

    Abdulah Gagić; Selma Selimović; Suad Jukić; Ajla Ališah; Aida Kustura

    2014-01-01

    It is common that experts use routine procedures for disinfection. Every part of the disinfection procedure is routinely done: preparation of the disinfection media, selection of the type of disinfection, protective measures, effect control and environmental issues. This article offers a new insight into the use of stabilized liquid chlorine dioxide as a qualitative alternative disinfectant for wider application by comparing it to the most frequently used chlorine and its compounds. When used...

  8. Phase equilibria in stratified thin liquid films stabilized by colloidal particles

    OpenAIRE

    Blawzdziewicz, J.; Wajnryb, E.

    2005-01-01

    Phase equilibria between regions of different thickness in thin liquid films stabilized by colloidal particles are investigated using a quasi-two-dimensional thermodynamic formalism. Appropriate equilibrium conditions for the film tension, normal pressure, and chemical potential of the particles in the film are formulated, and it is shown that the relaxation of these parameters occurs consecutively on three distinct time scales. Film stratification is described quantitatively for a hard-spher...

  9. Continuous Hydrolysis and Liquid–Liquid Phase Separation of an Active Pharmaceutical Ingredient Intermediate Using a Miniscale Hydrophobic Membrane Separator

    DEFF Research Database (Denmark)

    Cervera Padrell, Albert Emili; Morthensen, Sofie Thage; Lewandowski, Daniel Jacob

    2012-01-01

    Continuous hydrolysis of an active pharmaceutical ingredient intermediate, and subsequent liquid–liquid (L-L) separation of the resulting organic and aqueous phases, have been achieved using a simple PTFE tube reactor connected to a miniscale hydrophobic membrane separator. An alkoxide product...... a PTFE membrane with 28 cm2 of active area. A less challenging separation of water and toluene was achieved at total flow rates as high as 80 mL/min, with potential to achieve even higher flow rates. The operability and flexibility of the membrane separator and a plate coalescer were compared...

  10. The Effect of Covalently-Attached ATRP-Synthesized Polymers on Membrane Stability and Cytoprotection in Human Erythrocytes.

    Science.gov (United States)

    Clafshenkel, William P; Murata, Hironobu; Andersen, Jill; Creeger, Yehuda; Koepsel, Richard R; Russell, Alan J

    2016-01-01

    Erythrocytes have been described as advantageous drug delivery vehicles. In order to ensure an adequate circulation half-life, erythrocytes may benefit from protective enhancements that maintain membrane integrity and neutralize oxidative damage of membrane proteins that otherwise facilitate their premature clearance from circulation. Surface modification of erythrocytes using rationally designed polymers, synthesized via atom-transfer radical polymerization (ATRP), may further expand the field of membrane-engineered red blood cells. This study describes the fate of ATRP-synthesized polymers that were covalently attached to human erythrocytes as well as the effect of membrane engineering on cell stability under physiological and oxidative conditions in vitro. The biocompatible, membrane-reactive polymers were homogenously retained on the periphery of modified erythrocytes for at least 24 hours. Membrane engineering stabilized the erythrocyte membrane and effectively neutralized oxidative species, even in the absence of free-radical scavenger-containing polymers. The targeted functionalization of Band 3 protein by NHS-pDMAA-Cy3 polymers stabilized its monomeric form preventing aggregation in the presence of the crosslinking reagent, bis(sulfosuccinimidyl)suberate (BS3). A free radical scavenging polymer, NHS-pDMAA-TEMPO˙, provided additional protection of surface modified erythrocytes in an in vitro model of oxidative stress. Preserving or augmenting cytoprotective mechanisms that extend circulation half-life is an important consideration for the use of red blood cells for drug delivery in various pathologies, as they are likely to encounter areas of imbalanced oxidative stress as they circuit the vascular system.

  11. The Effect of Covalently-Attached ATRP-Synthesized Polymers on Membrane Stability and Cytoprotection in Human Erythrocytes.

    Directory of Open Access Journals (Sweden)

    William P Clafshenkel

    Full Text Available Erythrocytes have been described as advantageous drug delivery vehicles. In order to ensure an adequate circulation half-life, erythrocytes may benefit from protective enhancements that maintain membrane integrity and neutralize oxidative damage of membrane proteins that otherwise facilitate their premature clearance from circulation. Surface modification of erythrocytes using rationally designed polymers, synthesized via atom-transfer radical polymerization (ATRP, may further expand the field of membrane-engineered red blood cells. This study describes the fate of ATRP-synthesized polymers that were covalently attached to human erythrocytes as well as the effect of membrane engineering on cell stability under physiological and oxidative conditions in vitro. The biocompatible, membrane-reactive polymers were homogenously retained on the periphery of modified erythrocytes for at least 24 hours. Membrane engineering stabilized the erythrocyte membrane and effectively neutralized oxidative species, even in the absence of free-radical scavenger-containing polymers. The targeted functionalization of Band 3 protein by NHS-pDMAA-Cy3 polymers stabilized its monomeric form preventing aggregation in the presence of the crosslinking reagent, bis(sulfosuccinimidylsuberate (BS3. A free radical scavenging polymer, NHS-pDMAA-TEMPO˙, provided additional protection of surface modified erythrocytes in an in vitro model of oxidative stress. Preserving or augmenting cytoprotective mechanisms that extend circulation half-life is an important consideration for the use of red blood cells for drug delivery in various pathologies, as they are likely to encounter areas of imbalanced oxidative stress as they circuit the vascular system.

  12. Stability of an unsupported multi-layer surfactant laden liquid curtain under gravity

    KAUST Repository

    Henry, D.

    2015-11-07

    The industrial process of curtain coating has long been an important method in coating applications, by which a thin liquid curtain is formed to impinge upon a moving substrate, due to its highly lucrative advantage of being able to coat multiple layers simultaneously. We investigate the linear stability of an unsupported two-layer liquid curtain, which has insoluble surfactants in both liquids, which are widely used in industry to increase the stability of the curtain. We formulate the governing equations, simplified by making a thin film approximation, from which we obtain equations describing the steady-state profiles. We then examine the response of the curtain to small perturbations about this steady state to identify conditions under which the curtain is unstable, finding the addition of surfactants stabilizes the curtain. Our results are then compared to experimental data, showing a favourable trend and thereby extending the works of Brown (J Fluid Mech 10:297–305, 1960) and Dyson et al. (J Eng Math 64:237–250, 2009).

  13. Mechanical Stability of H3PO4-Doped PBI/Hydrophilic-Pretreated PTFE Membranes for High Temperature PEMFCs

    International Nuclear Information System (INIS)

    Park, Jaehyung; Wang, Liang; Advani, Suresh G.; Prasad, Ajay K.

    2014-01-01

    Graphical abstract: - Highlights: • PBI/PTFE membrane was prepared by porous PTFE with hydrophilic surface pretreatment. • The durability of the prepared PBI/PTFE membrane was compared with pure PBI, PBI with untreated PTFE, and PBI-Nafion with untreated PTFE membranes. • Accelerated durability tests and SEM showed improved durability based the PBI/PTFE membrane with pretreated PTFE. - Abstract: A novel polybenzimidazole (PBI)/poly(tetrafluoroethylene) (PTFE) composite membrane doped with phosphoric acid was fabricated for high temperature operation in a polymer electrolyte membrane (PEM) fuel cell. A hydrophilic surface pretreatment was applied to the porous PTFE matrix film to improve its interfacial adhesion to the PBI polymer, thereby avoiding the introduction of Nafion ionomer which is traditionally used as a coupling agent. The pretreated PTFE film was embedded within the composite membrane during solution-casting using 5wt% PBI/DMAc solution. The mechanical stability and durability of three types of MEAs assembled with PBI only, PBI with pretreated PTFE, and PBI-Nafion with untreated PTFE membranes were evaluated under an accelerated degradation testing protocol employing extreme temperature cycling. Degradation was characterized by recording polarization curves, hydrogen crossover, and proton resistance. Cross-sections of the membranes were examined before and after thermal cycling by scanning electron microscope. Energy-dispersive X-ray spectroscopy verified that the PBI is dispersed homogeneously in the porous PTFE matrix. Results show that the PBI composite membrane with pretreated PTFE has a lower degradation rate than the Nafion/PBI membrane with untreated PTFE. Thus, the hydrophilic pretreatment employed here greatly improved the mechanical stability of the composite membrane, which resulted in improved durability under an extreme thermal cycling regime

  14. The effects of an external signal on internal stochastic resonance in a liquid membrane oscillator

    International Nuclear Information System (INIS)

    Li Qianshu; Li Yaping

    2003-01-01

    Internal stochastic resonance (ISR) in a liquid membrane oscillator is investigated by varying frequency (ω s ) and amplitude (A) of an external signal (ES) in the presence of environment noise. It is found that the enhancement or suppression of ISR depends on frequency and amplitude of ES. In the range of low frequency (0.03-0.12 Hz), ISR appears and noise can transfer energy of ES to IS both for A=0.02 M and for A=0.15 M. In the range of high frequency (0.26-0.32 Hz), there exits an optimal frequency for ES, which is equal to frequency of IS and makes ISR strength reach maximum for A=0.02 M; but ISR disappears for A=0.15 M. At the optimal frequency ω s =0.28 Hz, a critical amplitude A c for ES is found, less than which, ISR appears, and more than which, ISR disappears

  15. Transport of uranium (VI) through a supported liquid membrane containing LIX 63

    International Nuclear Information System (INIS)

    Akiba, K.; Kanno, T.

    1983-01-01

    The carrier transport of U(VI) has been studied by means of the liquid membrane of LIX 63 (HR) held on a porous support. U was effectively transported from the dilute feed solution (pH = 4-5) to the product solution of 0.1 M H 2 SO 4 . Its concentration in the feed decreased according to [U]/sub f,t/ = [U]/sub f,0/ exp (-k/sub obs/t). The apparent rate constant (k/sub obs/) increased with an increase in carrier concentration up to 0.05 M, but it became nearly constant in the range of [HR] = 0.05-0.2 M. The rate of transport was inversely proportional to the feed volume. More than 99% of U was recovered and the final concentration ratio in the product to the feed ([U]/sub p//[U]/sub f/) exceeded 10 3 . 7 figures, 2 tables

  16. Electromembrane extraction with alkylated phosphites and phosphates as supported liquid membranes

    DEFF Research Database (Denmark)

    Huang, Chuixiu; Gjelstad, Astrid; Pedersen-Bjergaard, Stig

    2017-01-01

    A range of alkylated phosphates and phosphites were for the first time investigated as potential supported liquid membranes (SLMs) for electromembrane extraction (EME) of basic drugs from human plasma samples. Six polar basic drugs were used as model analytes for initial testing of the different...... on this observation, hydrogen-bonding interactions were hypothesized to play a dominant role in the partition of the charged polar model analytes into the SLM. The successful solvents also contained alkyl moieties equivalent to 12–18 carbon atoms. Interestingly, similar phosphates/phosphites with aromatic character...... were unsuccessful. Alkylated phosphates/phosphites with less carbon atoms resulted in high current flowing in the system, whereas similar structures with >18 carbon atoms provided very low recoveries and extremely low system-current. Based on this knowledge, an SLM of TBP mixed with 40% NPOE (2...

  17. Performance and Long Term Stability of Mesoporous Silica Membranes for Desalination

    Science.gov (United States)

    Elma, Muthia; Yacou, Christelle; Diniz da Costa, João C.; Wang, David K.

    2013-01-01

    This work shows the preparation of silica membranes by a two-step sol-gel method using tetraethyl orthosilicate in ethanolic solution by employing nitric acid and ammonia as co-catalysts. The sols prepared in pH 6 resulted in the lowest concentration of silanol (Si–OH) species to improve hydrostability and the optimized conditions for film coating. The membrane was tested to desalinate 0.3–15 wt % synthetic sodium chloride (NaCl) solutions at a feed temperature of 22 °C followed by long term membrane performance of up to 250 h in 3.5 wt % NaCl solution. Results show that the water flux (and salt rejection) decrease with increasing salt concentration delivering an average value of 9.5 kg m–2 h–1 (99.6%) and 1.55 kg m–2 h–1 (89.2%) from the 0.3 and 15 wt % saline feed solutions, respectively. Furthermore, the permeate salt concentration was measured to be less than 600 ppm for testing conditions up to 5 wt % saline feed solutions, achieving below the recommended standard for potable water. Long term stability shows that the membrane performance in water flux was stable for up to 150 h, and slightly reduced from thereon, possibly due to the blockage of large hydrated ions in the micropore constrictions of the silica matrix. However, the integrity of the silica matrix was not affected by the long term testing as excellent salt rejection of >99% was maintained for over 250 h. PMID:24956942

  18. Stability study and lyophilization of vitamin E-loaded nanocapsules prepared by membrane contactor.

    Science.gov (United States)

    Khayata, N; Abdelwahed, W; Chehna, M F; Charcosset, C; Fessi, H

    2012-12-15

    In this research, we studied the accelerated stability of vitamin E-loaded nanocapsules (NCs) prepared by the nanoprecipitation method. Vitamin E-loaded NCs were optimized firstly at the laboratory scale and then scaled up using the membrane contactor technique. The optimum conditions of the membrane contactor preparation (pilot scale) produced vitamin E-loaded NCs with an average size of 253 nm, polydispersity index 0.19 and a zeta potential -16 mV. The average size, polydispersity index and zeta potential values were 185 nm, 0.12 and -15 mV, respectively for the NCs prepared at laboratory scale. No significant changes were noticed in these values after 3 and 6 months of storage at high temperature (40±2 °C) and relative humidity (75±5%) in spite of vitamin E sensitivity to light, heat and oxygen. The entrapment efficiency of NCs prepared at pilot scale was 97% at the beginning of the stability study, and became (95%, 59%) after 3 and 6 months of storage, respectively. These values at lab-scale were (98%, 96%, and 89%) at time zero and after 3 and 6 months of storage, respectively. This confirms the ability of vitamin E encapsulation to preserve its stability, which is one major goal of our work. Lyophilization of the optimized formula at lab-scale was also performed. Four types of cryoprotectants were tested (poly(vinyl pyrrolidone), sucrose, mannitol, and glucose). Freeze-dried NCs prepared with sucrose were found acceptable. The other lyophilized NCs obtained at different conditions presented large aggregates. Copyright © 2012 Elsevier B.V. All rights reserved.

  19. Purity and stability of the membrane-limited glucocorticoid receptor agonist dexamethasone-BSA.

    Science.gov (United States)

    Weiss, Grant L; Rainville, Jennifer R; Zhao, Qi; Tasker, Jeffrey G

    2017-09-20

    Cellular effects of glucocorticoids can be separated into classical transcriptional regulation via activation of the canonical nuclear glucocorticoid receptor and rapid actions mediated by activation of one or more putative membrane-associated glucocorticoid receptors that regulate both transcriptional and non-transcriptional signaling. Dexamethasone-bovine serum albumin (Dex-BSA) is one of several membrane-limited steroid receptor agonists. Dex-BSA and other steroid conjugates such as corticosterone-, estradiol- and testosterone-BSA have been used to study rapid steroid effects initiated by putative membrane receptors. The purity and stability of the steroid-BSA conjugate is crucial, therefore, since any steroid that is not bound to or that dissociates from the BSA conjugate could penetrate into the intracellular compartment and confound the experiment. We used fluorine NMR to determine if free Dex could be detected in a commercially available Dex-BSA dissolved in H 2 O. Non-covalently bound Dex was detected in the Dex-BSA solution, but the level of free Dex remained constant over time and with increasing temperature, indicating that the free Dex was not a result of instability of the Dex-BSA conjugate. The free Dex was lost when the Dex-BSA was denatured and subjected to dialysis, which suggested that it was trapped in the Dex-BSA three-dimensional structure and not covalently bound to the BSA. The purified, renatured Dex-BSA retained its rapid activity, which confirmed that the observed effects of Dex-BSA are not caused by non-covalently-bound Dex. Therefore, the Dex contaminant found in the Dex-BSA solution is likely to be tightly, but non-covalently, bound to BSA, and the Dex-BSA activity remains membrane-limited. Our findings indicate that Dex-BSA remains a suitable membrane-restricted glucocorticoid receptor agonist, but suggest that denaturing purification is a useful control for the study of membrane-initiated steroid-BSA actions. Copyright © 2017

  20. Thermoresponsive Membrane Based on Thermotropic Liquid Crystalline Cholesteryl - (L-lacticacidn System: Study of Its Drug Permeability

    Directory of Open Access Journals (Sweden)

    Massoumeh Bagheri

    2013-01-01

    Full Text Available The rapidly increasing interest in functional materials with reversibly switchable physico- chemical properties has led to significant work on the development of stimuli responsive membranes. Thermotropic liquid crystals with their exceptional properties have potentials for drug-delivery applications. Thermoresponsive liquid-crystal-embedded membranes were investigated for the purpose of developing the drug delivery systems with thermal stimuli response. Drug release occurs at temperatures above the phase transition temperature of thermotropic liquid crystals. Therefore, they can control drug release in response to small temperature changes. In this work, the biocompatible and thermotropic liquid crystalline polymer cholesteryl-(L-lactic acidn ,CLAn (n=30, was synthesized with accurate control of molecular weight via ring opening polymerization method. Polymerization of L-lactide was carried out in the presence of cholesterol as an initiator and catalytic amount of tin (II octoate (Sn(Oct2 at 150°C in 5 h. The number-average degree of polymerization of CLA 30 was obtained from 1H NMR spectroscopy. The phase transition behavior of liquid crystalline CLA30 was established by differential scanning calorimetry and polarizing optical microscopy. The resulting liquid crystalline CLA30 was subsequently utilized to prepare CLA30 -embedded cellulose nitrate membrane by adsorption method. The CLA30-embedded cellulose nitrate membrane was used by an in-vitro drug penetration studies. Acetaminophen was used as a model drug. The permeation study was carried out at different temperatures around glass transition temperature of polymer CLA30 (37, 45 and 40°C, respectively. The results show that the CLA30 -embedded cellulose nitrate membranes exhibit thermo-responsive sensitivity with controlled drug permeation.

  1. Peptide insertion, positioning, and stabilization in a membrane: insight from an all-atom molecular dynamics simulation.

    Science.gov (United States)

    Babakhani, Arneh; Gorfe, Alemayehu A; Gullingsrud, Justin; Kim, Judy E; Andrew McCammon, J

    Peptide insertion, positioning, and stabilization in a model membrane are probed via an all-atom molecular dynamics (MD) simulation. One peptide (WL5) is simulated in each leaflet of a solvated dimyristoylglycero-3-phosphate (DMPC) membrane. Within the first 5 ns, the peptides spontaneously insert into the membrane and then stabilize during the remaining 70 ns of simulation time. In both leaflets, the peptides localize to the membrane interface, and this localization is attributed to the formation of peptide-lipid hydrogen bonds. We show that the single tryptophan residue in each peptide contributes significantly to these hydrogen bonds; specifically, the nitrogen heteroatom of the indole ring plays a critical role. The tilt angles of the indole rings relative to the membrane normal in the upper and lower leaflets are approximately 26 degrees and 54 degrees , respectively. The tilt angles of the entire peptide chain are 62 degrees and 74 degrees . The membrane induces conformations of the peptide that are characteristic of beta-sheets, and the peptide enhances the lipid ordering in the membrane. Finally, the diffusion rate of the peptides in the membrane plane is calculated (based on experimental peptide concentrations) to be approximately 6 A(2)/ns, thus suggesting a 500 ns time scale for intermolecular interactions.

  2. A New Emulsion Liquid Membrane Based on a Palm Oil for the Extraction of Heavy Metals

    Directory of Open Access Journals (Sweden)

    Sanna Björkegren

    2015-04-01

    Full Text Available The extraction efficiency of hexavalent chromium, Cr(VI, from water has been investigated using a vegetable oil based emulsion liquid membrane (ELM technique. The main purpose of this study was to create a novel ELM formulation by choosing a more environmentally friendly and non-toxic diluent such as palm oil. The membrane phase so formulated includes the mobile carrier tri-n-octylmethylammonium chloride (TOMAC, to facilitate the metal transport, and the hydrophilic surfactant Tween 80 to facilitate the dispersion of the ELM phase in the aqueous solution. Span 80 is used as surfactant and butanol as co-surfactant. Our results demonstrate that this novel ELM formulation, using the vegetable palm oil as diluent, is useful for the removal of hexavalent chromium with an efficiency of over 99% and is thus competitive with the already existing, yet less environmentally friendly, ELM formulations. This result was achieved with an optimal concentration of 0.1 M NaOH as stripping agent and an external phase pH of 0.5. Different water qualities have also been investigated showing that the type of water (deionized, distilled, or tap water does not significantly influence the extraction rate.

  3. Application of functionalized calixarenes to the processing of radioactive effluents by supported liquid membranes

    International Nuclear Information System (INIS)

    Hill, Clement

    1994-01-01

    In a first part, this research thesis presents the general context of nuclear waste processing (nature of wastes to be processed, characteristics of the used method and products), and proposes an overview of results obtained during previous campaigns which were based on the use of the technique of supported liquid membranes, but with other types of extracting components. The second part focuses on the tracking of complexing and extractive properties of all functionalized calixarenes which had been synthesised by different research teams. Several experiments have been performed to determine the extraction efficiency and selectivity of these organic compounds with respect to the studied radio-elements. The third part reports the detailed study of a specific family of functionalized calixarenes for which two thermodynamic models of membrane transport described in the literature have been applied. Validity limits are discussed with respect to operation conditions. Some results are finally given on the caesium and actinide (neptunium, plutonium) decontamination of synthetic concentrates which simulate actual radioactive wastes [fr

  4. Mixed reverse micelles facilitated downstream processing of lipase involving water-oil-water liquid emulsion membrane.

    Science.gov (United States)

    Bhowal, Saibal; Priyanka, B S; Rastogi, Navin K

    2014-01-01

    Our earlier work for the first time demonstrated that liquid emulsion membrane (LEM) containing reverse micelles could be successfully used for the downstream processing of lipase from Aspergillus niger. In the present work, we have attempted to increase the extraction and purification fold of lipase by using mixed reverse micelles (MRM) consisting of cationic and nonionic surfactants in LEM. It was basically prepared by addition of the internal aqueous phase solution to the organic phase followed by the redispersion of the emulsion in the feed phase containing enzyme, which resulted in globules of water-oil-water (WOW) emulsion for the extraction of lipase. The optimum conditions for maximum lipase recovery (100%) and purification fold (17.0-fold) were CTAB concentration 0.075 M, Tween 80 concentration 0.012 M, at stirring speed of 500 rpm, contact time 15 min, internal aqueous phase pH 7, feed pH 9, KCl concentration 1 M, NaCl concentration 0.1 M, and ratio of membrane emulsion to feed volume 1:1. Incorporation of the nonionic surfactant (e.g., Tween 80) resulted in remarkable improvement in the purification fold (3.1-17.0) of the lipase. LEM containing a mixture of nonionic and cationic surfactants can be successfully used for the enhancement in the activity recovery and purification fold during downstream processing of enzymes/proteins. © 2014 American Institute of Chemical Engineers.

  5. Highly Sulfonated Diamine Synthesized Polyimides and Protic Ionic Liquid Composite Membranes Improve PEM Conductivity

    Directory of Open Access Journals (Sweden)

    Bor-Kuan Chen

    2015-06-01

    Full Text Available A novel sulfonated diamine was synthesized from 1,4-bis(4-aminophenoxy benzene [pBAB]. Sulfonated polyimides (SPIs were synthesized from sulfonated pBAB, 1,4-bis(4-aminophenoxy-2-sulfonic acid benzenesulfonic acid [pBABTS], various diamines and aromatic dianhydrides. Composite proton exchange membranes (PEMs made of novel SPIs and a protic ionic liquid (PIL 1-vinyl-3-H-imidazolium trifluoromethanesulfonate [VIm][OTf] showed substantially increased conductivity. We prepared an SPI/PIL composite PEM using pBABTS, 4,4′-(9-fluorenylidene dianiline (9FDA as diamine, 3,3′,4,4′-diphenylsulfone tetracarboxylic dianhydride (DSDA as dianhydride and 40 wt % [VIm][OTf] with a high conductivity of 16 mS/cm at 120 °C and anhydrous condition. pBABTS offered better conductivity, since the chemical structure had more sulfonated groups that provide increased conductivity. The new composite membrane could be a promising anhydrous or low-humidity PEM for intermediate or high-temperature fuel cells.

  6. Nonlinear stability analysis of the thin pseudoplastic liquid film flowing down along a vertical wall

    International Nuclear Information System (INIS)

    Cheng, Po-Jen; Chen, Cha'o-Kuang; Lai, Hsin-Yi

    2001-01-01

    This article investigates the weakly nonlinear stability theory of a thin pseudoplastic liquid film flowing down on a vertical wall. The long-wave perturbation method is employed to solve for generalized nonlinear kinematic equation with free film interface. The normal mode approach is used to compute the linear stability solution for the film flow. The method of multiple scales is then used to obtain the weak nonlinear dynamics of the film flow for stability analysis. It is shown that the necessary condition for the existence of such a solution is governed by the Ginzburg - Landau equation. The modeling results indicate that both subcritical instability and supercritical stability conditions are possible to occur in a pseudoplastic film flow system. The results also reveal that the pseudoplastic liquid film flows are less stable than Newtonian's as traveling down along the vertical wall. The degree of instability in the film flow is further intensified by decreasing the flow index n. [copyright] 2001 American Institute of Physics

  7. Universal emulsion stabilization from the arrested adsorption of rough particles at liquid-liquid interfaces.

    Science.gov (United States)

    Zanini, Michele; Marschelke, Claudia; Anachkov, Svetoslav E; Marini, Emanuele; Synytska, Alla; Isa, Lucio

    2017-06-07

    Surface heterogeneities, including roughness, significantly affect the adsorption, motion and interactions of particles at fluid interfaces. However, a systematic experimental study, linking surface roughness to particle wettability at a microscopic level, is currently missing. Here we synthesize a library of all-silica microparticles with uniform surface chemistry, but tuneable surface roughness and study their spontaneous adsorption at oil-water interfaces. We demonstrate that surface roughness strongly pins the particles' contact lines and arrests their adsorption in long-lived metastable positions, and we directly measure the roughness-induced interface deformations around isolated particles. Pinning imparts tremendous contact angle hysteresis, which can practically invert the particle wettability for sufficient roughness, irrespective of their chemical nature. As a unique consequence, the same rough particles stabilize both water-in-oil and oil-in-water emulsions depending on the phase they are initially dispersed in. These results both shed light on fundamental phenomena concerning particle adsorption at fluid interfaces and indicate future design rules for particle-based emulsifiers.

  8. Simultaneous micro-electromembrane extractions of anions and cations using multiple free liquid membranes and acceptor solutions

    Czech Academy of Sciences Publication Activity Database

    Kubáň, Pavel; Boček, Petr

    2016-01-01

    Roč. 908, FEB (2016), s. 113-120 ISSN 0003-2670 R&D Projects: GA ČR(CZ) GA13-05762S Institutional support: RVO:68081715 Keywords : free liquid membranes * micro-electromembrane extraction * simultaneous extractions Subject RIV: CB - Analytical Chemistry , Separation Impact factor: 4.950, year: 2016

  9. Effect of the Phase Volume Ratio on the Potential of a Liquid-Membrane Ion-Selective Electrode

    Czech Academy of Sciences Publication Activity Database

    Samec, Zdeněk; Girault, H. H.

    2004-01-01

    Roč. 76, č. 14 (2004), s. 4150-4155 ISSN 0003-2700 R&D Projects: GA MŠk ME 502 Institutional research plan: CEZ:AV0Z4040901 Keywords : liquit-membrane * ion-selective electrode * two.phase liquid system Subject RIV: CG - Electrochemistry Impact factor: 5.450, year: 2004

  10. Membrane stability of sickle erythrocytes incubated in extracts of three medicinal plants: Anacardium occidentale, Psidium guajava, and Terminalia catappa.

    Science.gov (United States)

    Chikezie, Paul Chidoka; Uwakwe, Augustine Amadikwa

    2011-04-01

    Many reports showed that medicinal plant extracts cause alterations on the shape and physiology of erythrocytes. The present study seeks to ascertain the osmotic stability of sickle erythrocytes incubated in aqueous extracts of Anacardium occidentale, Psidium guajava, and Terminalia catappa. The fraction of erythrocytes lysed when suspended in saline solution of varying concentrations was investigated by spectrophotometric method. The percentage hemolysis of erythrocytes in the control and test samples showed a sigmoidal relationship with increasing concentrations of saline solution. Membrane stability was ascertained as mean corpuscular fragility (MCF) index of erythrocytes incubated in 400 and 800 mg/dL aqueous concentrations of the three plant extracts. The two experimental concentrations of P. guajava and T. catappa protected the erythrocytes against osmotic stress, as evidenced by decreases in the values of MCF compared with the control sample (P catappa stabilized erythrocyte membrane, higher concentration (800 mg/dL) of A. occidentale exhibited no membrane protective effect.

  11. Parallel artificial liquid membrane extraction of new psychoactive substances in plasma and whole blood.

    Science.gov (United States)

    Vårdal, Linda; Askildsen, Hilde-Merete; Gjelstad, Astrid; Øiestad, Elisabeth Leere; Edvardsen, Hilde Marie Erøy; Pedersen-Bjergaard, Stig

    2017-03-24

    Parallel artificial liquid membrane extraction (PALME) was combined with ultra-high performance liquid chromatography-mass spectrometry (UHPLC-MS) and the potential for screening of new psychoactive substances (NPS) was investigated for the first time. PALME was performed in 96-well format comprising a donor plate, a supported liquid membrane (SLM), and an acceptor plate. Uncharged NPS were extracted from plasma or whole blood, across an organic SLM, and into an aqueous acceptor solution, facilitated by a pH gradient. MDAI (5,6-methylenedioxy-2-aminoindane), methylone, PFA (para-fluoroamphetamine), mCPP (meta-chlorophenylpiperazine), pentedrone, methoxetamine, MDPV (methylenedioxypyrovalerone), ethylphenidate, 2C-E (2,5-dimethoxy-4-ethylphenethylamine), bromo-dragonfly, and AH-7921 (3,4-dichloro-N-{[1-(dimethylamino)cyclohexyl]methyl}benzamide) were selected as representative NPS. Optimization of operational parameters was necessary as the NPS were novel to PALME, and because PALME was performed from whole blood for the very first time. In the PALME method developed for plasma, NPS were extracted from a 250μL alkalized donor solution consisting of 125μL plasma sample, 115μL 40mM NaOH, and 10μL internal standard. In the PALME method from whole blood, the 250μL alkalized donor solution consisted of 100μL whole blood, 50μL deionized water, 75μL 80mM NaOH, and 25μL internal standard. In both methods, extraction was accomplished across an SLM of 5μL dodecyl acetate with 1% trioctylamine (w/w), and further into an acidic acceptor solution of 50μL 20mM formic acid. The extraction was promoted by agitation at 900rpm and was carried out for 120min. Method validation was performed and the following parameters were considered: linearity, limits of quantification (LOQ), intra- and inter-day precision, accuracy, extraction recoveries, carry-over, and matrix effects. The validation results were in accordance with FDA guidelines. Copyright © 2017 Elsevier B.V. All

  12. Membrane protein stability can be compromised by detergent interactions with the extramembranous soluble domains.

    Science.gov (United States)

    Yang, Zhengrong; Wang, Chi; Zhou, Qingxian; An, Jianli; Hildebrandt, Ellen; Aleksandrov, Luba A; Kappes, John C; DeLucas, Lawrence J; Riordan, John R; Urbatsch, Ina L; Hunt, John F; Brouillette, Christie G

    2014-06-01

    Detergent interaction with extramembranous soluble domains (ESDs) is not commonly considered an important determinant of integral membrane protein (IMP) behavior during purification and crystallization, even though ESDs contribute to the stability of many IMPs. Here we demonstrate that some generally nondenaturing detergents critically destabilize a model ESD, the first nucleotide-binding domain (NBD1) from the human cystic fibrosis transmembrane conductance regulator (CFTR), a model IMP. Notably, the detergents show equivalent trends in their influence on the stability of isolated NBD1 and full-length CFTR. We used differential scanning calorimetry (DSC) and circular dichroism (CD) spectroscopy to monitor changes in NBD1 stability and secondary structure, respectively, during titration with a series of detergents. Their effective harshness in these assays mirrors that widely accepted for their interaction with IMPs, i.e., anionic > zwitterionic > nonionic. It is noteworthy that including lipids or nonionic detergents is shown to mitigate detergent harshness, as will limiting contact time. We infer three thermodynamic mechanisms from the observed thermal destabilization by monomer or micelle: (i) binding to the unfolded state with no change in the native structure (all detergent classes); (ii) native state binding that alters thermodynamic properties and perhaps conformation (nonionic detergents); and (iii) detergent binding that directly leads to denaturation of the native state (anionic and zwitterionic). These results demonstrate that the accepted model for the harshness of detergents applies to their interaction with an ESD. It is concluded that destabilization of extramembranous soluble domains by specific detergents will influence the stability of some IMPs during purification. © 2014 The Protein Society.

  13. Role of the interosseous membrane and annular ligament in stabilizing the proximal radial head.

    Science.gov (United States)

    Anderson, Ashley; Werner, Frederick W; Tucci, Emily R; Harley, Brian J

    2015-12-01

    The purpose of our study was to determine the relative contributions of the annular ligament, proximal band, central band, and distal band of the interosseous membrane in preventing dislocation of the proximal radius. In part 1 of the study, 8 forearms were loaded transversely with the forearm intact, and the central band, proximal band, and annular ligament were sequentially sectioned to determine the percentage contribution of each structure in preventing transverse radial displacement. In part 2, 12 forearms were cyclically supinated and pronated while optical sensors measured radial and ulnar motion. Transverse radial head motion was computed as the distal band, central band, and proximal band (and annular ligament) were sequentially sectioned. In part 1, there was no significant difference in the percentage contribution of each structure in preventing radial transverse displacement. In part 2, only after sectioning of the central band did significant radial head displacement occur. Greater displacements occurred in supination than in pronation. Dislocation of the proximal radius occurred in 2 arms after sectioning of all 3 structures. Under pure transverse displacement, the central band, annular ligament, and proximal band equally contributed to stabilizing the radius. However, during forearm rotation, the central band contributed more to radial head stability than the annular ligament and proximal band. Our study contributes to our knowledge of forearm biomechanics, demonstrating the importance of the central band in providing proximal radial head stability. Forceful supination should be avoided after surgical procedures designed to stabilize the radial head. Copyright © 2015 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Elsevier Inc. All rights reserved.

  14. Separation of cadmium and lead from wastewater using supported liquid membrane integrated with in-situ electrodeposition

    International Nuclear Information System (INIS)

    Bhatluri, Kamal Kumar; Manna, Mriganka Sekhar; Ghoshal, Aloke Kumar; Saha, Prabirkumar

    2017-01-01

    A novel process for separation of heavy metals from liquid wastes and/or industrial effluents has been developed as described in this paper wherein the technique of supported liquid membrane based extraction and stripping of heavy metals has been augmented with electroplating inside the stripping chamber of SLM. Wastewater, infested with cadmium and lead, has been subject of research in this work. The said process is employed in transporting the heavy metals from the polluted source phase (wastewater) to the sink (or strip) phase while simultaneously depositing the heavy metals in-situ on the electrode placed inside the strip phase, and thereby the strip phase is remained ever-unsaturated. This arrangement yields high gradient of chemical potential across the liquid membrane and thereby facilitates enhanced and faster recovery of said heavy metals and also yields value added component, viz. electroplated items, for suitable end use.

  15. High temperature ceramic membrane reactors for coal liquid upgrading. Final report, September 21, 1989--November 20, 1992

    Energy Technology Data Exchange (ETDEWEB)

    Tsotsis, T.T. [University of Southern California, Los Angeles, CA (United States). Dept. of Chemical Engineering; Liu, P.K.T. [Aluminum Co. of America, Pittsburgh, PA (United States); Webster, I.A. [Unocal Corp., Los Angeles, CA (United States)

    1992-12-31

    Membrane reactors are today finding extensive applications for gas and vapor phase catalytic reactions (see discussion in the introduction and recent reviews by Armor [92], Hsieh [93] and Tsotsis et al. [941]). There have not been any published reports, however, of their use in high pressure and temperature liquid-phase applications. The idea to apply membrane reactor technology to coal liquid upgrading has resulted from a series of experimental investigations by our group of petroleum and coal asphaltene transport through model membranes. Coal liquids contain polycyclic aromatic compounds, which not only present potential difficulties in upgrading, storage and coprocessing, but are also bioactive. Direct coal liquefaction is perceived today as a two-stage process, which involves a first stage of thermal (or catalytic) dissolution of coal, followed by a second stage, in which the resulting products of the first stage are catalytically upgraded. Even in the presence of hydrogen, the oil products of the second stage are thought to equilibrate with the heavier (asphaltenic and preasphaltenic) components found in the feedstream. The possibility exists for this smaller molecular fraction to recondense with the unreacted heavy components and form even heavier undesirable components like char and coke. One way to diminish these regressive reactions is to selectively remove these smaller molecular weight fractions once they are formed and prior to recondensation. This can, at least in principle, be accomplished through the use of high temperature membrane reactors, using ceramic membranes which are permselective for the desired products of the coal liquid upgrading process. An additional incentive to do so is in order to eliminate the further hydrogenation and hydrocracking of liquid products to undesirable light gases.

  16. Extraction of Lead through Supported Liquid Membrane Using Triethanolamine/Cyclohexanone Carrier and Na2SO4 strippant

    Directory of Open Access Journals (Sweden)

    Gill R.

    2013-04-01

    Full Text Available Supported liquid membranes (SLM have proved to be effective not only for removing but also for recovery of heavy metals from waste water. This work includes the study of separation and transport of Pb+2 ions through liquid membrane based on triethanolamine (TEA in cyclohexanone supported in microporous polypropylene films. Therefore, this study aims to optimize the conditions for moving the Pb+2 ions against the concentration gradient, characterize the membrane by flux measurements, for their use in various industrial plants design to recover these ions. The effect of lead ion concentration, HNO3 in feed and TEA concentration in membrane has been studied. Optimized condition of transport of this metal ion is 1.0 M acid concentration in the feed phase and 0.1M Na2SO4 as the strippant when TEA concentration is 5.25 mol/dm3 in the membrane, as the rationale of this study is to optimize the condition for the movement of lead ions from feed phase to strip phase and to recover metal ions from any industrial effluent and finally to characterize the membrane by determining the mobility and permeability of the complexed heavy metal ion to extract their respective metal ions.

  17. Carrier-mediated transport of trace quantity of plutonium across dicyclohexano-18-crown-6 / toluene liquid membrane from low alpha waste solutions (Preprint no. SST-09)

    International Nuclear Information System (INIS)

    Kumar, Anil; Singh, R.K.; Nair, M.K.T.; Shukla, J.P.

    1991-01-01

    Macrocycle-facilitated transport of Pu(IV) from plutonium nitrate solutions of extremely low concentration levels across bulk liquid membrane (BLM) and supported liquid membrane (SLM) was investigated. Most of the plutonium could be transported by employing 0.2M DC18C6/ toluene as carrier and sodium carbonate as strippant. Enka Accurel flat sheet polypropylene membrane was used for SLM. (author). 3 refs., 1 tab

  18. Systematic cyanobacterial membrane proteome analysis by combining acid hydrolysis and digestive enzymes with nano-liquid chromatography-Fourier transform mass spectrometry.

    Science.gov (United States)

    Kwon, Joseph; Oh, Jeehyun; Park, Chiyoul; Cho, Kun; Kim, Seung Il; Kim, Soohyun; Lee, Sunghoon; Bhak, Jong; Norling, Birgitta; Choi, Jong-Soon

    2010-01-15

    The identification of membrane proteins is currently under-represented since the trans-membrane domains of membrane proteins have a hydrophobic property. Membrane proteins have mainly been analyzed by cleaving and identifying exposed hydrophilic domains. We developed the membrane proteomics method for targeting integral membrane proteins by the following sequential process: in-solution acid hydrolysis, reverse phase chromatographic separation, trypsin or chymotrypsin digestion and nano-liquid chromatography-Fourier transform mass spectrometry. When we employed total membrane proteins of Synechocystis sp. PCC 6803, 155 integral membrane proteins out of a predictable 706 were identified in a single application, corresponding to 22% of a genome. The combined methods of acid hydrolysis-trypsin (AT) and acid hydrolysis-chymotrypsin (AC) identified both hydrophilic and hydrophobic domains of integral membrane proteins, respectively. The systematic approach revealed a more concrete data in mapping the repertoire of cyanobacterial membrane and membrane-linked proteome. 2009 Elsevier B.V. All rights reserved.

  19. Isomeric Detergent Comparison for Membrane Protein Stability: Importance of Inter-Alkyl-Chain Distance and Alkyl Chain Length.

    Science.gov (United States)

    Cho, Kyung Ho; Hariharan, Parameswaran; Mortensen, Jonas S; Du, Yang; Nielsen, Anne K; Byrne, Bernadette; Kobilka, Brian K; Loland, Claus J; Guan, Lan; Chae, Pil Seok

    2016-12-14

    Membrane proteins encapsulated by detergent micelles are widely used for structural study. Because of their amphipathic property, detergents have the ability to maintain protein solubility and stability in an aqueous medium. However, conventional detergents have serious limitations in their scope and utility, particularly for eukaryotic membrane proteins and membrane protein complexes. Thus, a number of new agents have been devised; some have made significant contributions to membrane protein structural studies. However, few detergent design principles are available. In this study, we prepared meta and ortho isomers of the previously reported para-substituted xylene-linked maltoside amphiphiles (XMAs), along with alkyl chain-length variation. The isomeric XMAs were assessed with three membrane proteins, and the meta isomer with a C 12 alkyl chain was most effective at maintaining solubility/stability of the membrane proteins. We propose that interplay between the hydrophile-lipophile balance (HLB) and alkyl chain length is of central importance for high detergent efficacy. In addition, differences in inter-alkyl-chain distance between the isomers influence the ability of the detergents to stabilise membrane proteins. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Glycosylation stabilizes hERG channels on the plasma membrane by decreasing proteolytic susceptibility.

    Science.gov (United States)

    Lamothe, Shawn M; Hulbert, Maggie; Guo, Jun; Li, Wentao; Yang, Tonghua; Zhang, Shetuan

    2018-01-05

    The human ether-a-go-go related gene ( hERG)-encoded channel hERG undergoes N-linked glycosylation at position 598, which is located in the unusually long S5-pore linker of the channel. In other work we have demonstrated that hERG is uniquely susceptible to proteolytic cleavage at the S5-pore linker by proteinase K (PK) and calpain (CAPN). The scorpion toxin BeKm-1, which binds to the S5-pore linker of hERG, protects hERG from such cleavage. In the present study, our data revealed that, compared with normal glycosylated hERG channels, nonglycosylated hERG channels were significantly more susceptible to cleavage by extracellular PK. Furthermore, the protective effect of BeKm-1 on hERG from PK-cleavage was lost when glycosylation of hERG was inhibited. The inactivation-deficient mutant hERG channels S620T and S631A were resistant to PK cleavage, and inhibition of glycosylation rendered both mutants susceptible to PK cleavage. Compared with normal glycosylated channels, nonglycosylated hERG channels were also more susceptible to cleavage mediated by CAPN, which was present in the medium of human embryonic kidney cells under normal culture conditions. Inhibition of CAPN resulted in an increase of nonglycosylated hERG current. In summary, our results revealed that N-linked glycosylation protects hERG against protease-mediated degradation and thus contributes to hERG channel stability on the plasma membrane.-Lamothe, S. M., Hulbert, M., Guo, J., Li, W., Yang, T., Zhang, S. Glycosylation stabilizes hERG channels on the plasma membrane by decreasing proteolytic susceptibility.

  1. Insertion of Neurotransmitters into a Lipid Bilayer Membrane and Its Implication on Membrane Stability: A Molecular Dynamics Study.

    Science.gov (United States)

    Shen, Chun; Xue, Minmin; Qiu, Hu; Guo, Wanlin

    2017-03-17

    The signaling molecules in neurons, called neurotransmitters, play an essential role in the transportation of neural signals, during which the neurotransmitters interact with not only specific receptors, but also cytomembranes, such as synaptic vesicle membranes and postsynaptic membranes. Through extensive molecular dynamics simulations, the atomic-scale insertion dynamics of typical neurotransmitters, including methionine enkephalin (ME), leucine enkephalin (LE), dopamine (DA), acetylcholine (ACh), and aspartic acid (ASP), into lipid bilayers is investigated. The results show that the first three neurotransmitters (ME, LE, and DA) are able to diffuse freely into both 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine (POPC) and 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphoethanolamine (POPE) membranes, and are guided by the aromatic residues Tyr and Phe. Only a limited number of these neurotransmitters are allowed to penetrate into the membrane, which suggests an intrinsic mechanism by which the membrane is protected from being destroyed by excessive inserted neurotransmitters. After spontaneous insertion, the neurotransmitters disturb the surrounding phospholipids in the membrane, as indicated by the altered distribution of components in lipid leaflets and the disordered lipid tails. In contrast, the last two neurotransmitters (ACh and ASP) cannot enter the membrane, but instead always diffuse freely in solution. These findings provide an understanding at the atomic level of how neurotransmitters interact with the surrounding cytomembrane, as well as their impact on membrane behavior. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Static Magnetic Field Attenuates Lipopolysaccharide-Induced Inflammation in Pulp Cells by Affecting Cell Membrane Stability

    Directory of Open Access Journals (Sweden)

    Sung-Chih Hsieh

    2015-01-01

    Full Text Available One of the causes of dental pulpitis is lipopolysaccharide- (LPS- induced inflammatory response. Following pulp tissue inflammation, odontoblasts, dental pulp cells (DPCs, and dental pulp stem cells (DPSCs will activate and repair damaged tissue to maintain homeostasis. However, when LPS infection is too serious, dental repair is impossible and disease may progress to irreversible pulpitis. Therefore, the aim of this study was to examine whether static magnetic field (SMF can attenuate inflammatory response of dental pulp cells challenged with LPS. In methodology, dental pulp cells were isolated from extracted teeth. The population of DPSCs in the cultured DPCs was identified by phenotypes and multilineage differentiation. The effects of 0.4 T SMF on DPCs were observed through MTT assay and fluorescent anisotropy assay. Our results showed that the SMF exposure had no effect on surface markers or multilineage differentiation capability. However, SMF exposure increases cell viability by 15%. In addition, SMF increased cell membrane rigidity which is directly related to higher fluorescent anisotropy. In the LPS-challenged condition, DPCs treated with SMF demonstrated a higher tolerance to LPS-induced inflammatory response when compared to untreated controls. According to these results, we suggest that 0.4 T SMF attenuates LPS-induced inflammatory response to DPCs by changing cell membrane stability.

  3. The stability of liquid-filled matrix ionization chamber electronic portal imaging devices for dosimetry purposes.

    Science.gov (United States)

    Louwe, R J W; Tielenburg, R; van Ingen, K M; Mijnheer, B J; van Herk, M B

    2004-04-01

    This study was performed to determine the stability of liquid-filled matrix ionization chamber (LiFi-type) electronic portal imaging devices (EPID) for dosimetric purposes. The short- and long-term stability of the response was investigated, as well as the importance of factors influencing the response (e.g., temperature fluctuations, radiation damage, and the performance of the electronic hardware). It was shown that testing the performance of the electronic hardware as well as the short-term stability of the imagers may reveal the cause of a poor long-term stability of the imager response. In addition, the short-term stability was measured to verify the validity of the fitted dose-response curve immediately after beam startup. The long-term stability of these imagers could be considerably improved by correcting for room temperature fluctuations and gradual changes in response due to radiation damage. As a result, the reproducibility was better than 1% (1 SD) over a period of two years. The results of this study were used to formulate recommendations for a quality control program for portal dosimetry. The effect of such a program was assessed by comparing the results of portal dosimetry and in vivo dosimetry using diodes during the treatment of 31 prostate patients. The improvement of the results for portal dosimetry was consistent with the deviations observed with the reproducibility tests in that particular period. After a correction for the variation in response of the imager, the average difference between the measured and prescribed dose during the treatment of prostate patients was -0.7%+/-1.5% (1 SD), and -0.6%+/-1.1% (1 SD) for EPID and diode in vivo dosimetry, respectively. It can be concluded that a high stability of the response can be achieved for this type of EPID by applying a rigorous quality control program.

  4. The influence of mesoscopic confinement on the dynamics of imidazolium-based room temperature ionic liquids in polyether sulfone membranes

    Science.gov (United States)

    Thomaz, Joseph E.; Bailey, Heather E.; Fayer, Michael D.

    2017-11-01

    The structural dynamics of a series of 1-alkyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (CnmimNTf2, n = 2, 4, 6, 10: ethyl—Emim; butyl—Bmim; hexyl—Hmim; decyl—Dmim) room temperature ionic liquids confined in the pores of polyether sulfone (PES 200) membranes with an average pore size of ˜350 nm and in the bulk liquids were studied. Time correlated single photon counting measurements of the fluorescence of the fluorophore coumarin 153 (C153) were used to observe the time-dependent Stokes shift (solvation dynamics). The solvation dynamics of C153 in the ionic liquids are multiexponential decays. The multiexponential functional form of the decays was confirmed as the slowest decay component of each bulk liquid matches the slowest component of the liquid dynamics measured by optical heterodyne-detected optical Kerr effect (OHD-OKE) experiments, which is single exponential. The fact that the slowest component of the Stokes shift matches the OHD-OKE data in all four liquids identifies this component of the solvation dynamics as arising from the complete structural randomization of the liquids. Although the pores in the PES membranes are large, confinement on the mesoscopic length scale results in substantial slowing of the dynamics, a factor of ˜4, for EmimNTf2, with the effect decreasing as the chain length increases. By DmimNTf2, the dynamics are virtually indistinguishable from those in the bulk liquid. The rotation relaxation of C153 in the four bulk liquids was also measured and showed strong coupling between the C153 probe and its environment.

  5. A Mechanistic Study of Chemically Modified Inorganic Membranes for Gas and Liquid Separations

    Energy Technology Data Exchange (ETDEWEB)

    Way, J. Douglas [Colorado School of Mines, Golden, CO (United States). Dept. of Chemical Engineering

    2011-01-21

    This final report will summarize the progress made during the period August 1, 1993 - October 31, 2010 with support from DOE grant number DE-FG03-93ER14363. The objectives of the research have been to investigate the transport mechanisms in micro- and mesoporous, metal oxide membranes and to examine the relationship between the microstructure of the membrane, the membrane surface chemistry, and the separation performance of the membrane. Examples of the membrane materials under investigation are the microporous silica hollow fiber membrane manufactured by PPG Industries, chemically modified mesoporous oxide membranes, and polymer membranes containing microporous oxides (mixed matrix membranes). Analytical techniques such as NMR, FTIR and Raman spectroscopy, thermal analysis, and gas adsorption were used to investigate membrane microstructure and to probe the chemical interactions occurring at the gas-membrane interface.

  6. Liquid exfoliation of solvent-stabilized few-layer black phosphorus for applications beyond electronics

    Science.gov (United States)

    Hanlon, Damien; Backes, Claudia; Doherty, Evie; Cucinotta, Clotilde S.; Berner, Nina C.; Boland, Conor; Lee, Kangho; Harvey, Andrew; Lynch, Peter; Gholamvand, Zahra; Zhang, Saifeng; Wang, Kangpeng; Moynihan, Glenn; Pokle, Anuj; Ramasse, Quentin M.; McEvoy, Niall; Blau, Werner J.; Wang, Jun; Abellan, Gonzalo; Hauke, Frank; Hirsch, Andreas; Sanvito, Stefano; O'Regan, David D.; Duesberg, Georg S.; Nicolosi, Valeria; Coleman, Jonathan N.

    2015-10-01

    Few-layer black phosphorus (BP) is a new two-dimensional material which is of great interest for applications, mainly in electronics. However, its lack of environmental stability severely limits its synthesis and processing. Here we demonstrate that high-quality, few-layer BP nanosheets, with controllable size and observable photoluminescence, can be produced in large quantities by liquid phase exfoliation under ambient conditions in solvents such as N-cyclohexyl-2-pyrrolidone (CHP). Nanosheets are surprisingly stable in CHP, probably due to the solvation shell protecting the nanosheets from reacting with water or oxygen. Experiments, supported by simulations, show reactions to occur only at the nanosheet edge, with the rate and extent of the reaction dependent on the water/oxygen content. We demonstrate that liquid-exfoliated BP nanosheets are potentially useful in a range of applications from ultrafast saturable absorbers to gas sensors to fillers for composite reinforcement.

  7. Liquid exfoliation of solvent-stabilized few-layer black phosphorus for applications beyond electronics

    Science.gov (United States)

    Hanlon, Damien; Backes, Claudia; Doherty, Evie; Cucinotta, Clotilde S.; Berner, Nina C.; Boland, Conor; Lee, Kangho; Harvey, Andrew; Lynch, Peter; Gholamvand, Zahra; Zhang, Saifeng; Wang, Kangpeng; Moynihan, Glenn; Pokle, Anuj; Ramasse, Quentin M.; McEvoy, Niall; Blau, Werner J.; Wang, Jun; Abellan, Gonzalo; Hauke, Frank; Hirsch, Andreas; Sanvito, Stefano; O'Regan, David D.; Duesberg, Georg S.; Nicolosi, Valeria; Coleman, Jonathan N.

    2015-01-01

    Few-layer black phosphorus (BP) is a new two-dimensional material which is of great interest for applications, mainly in electronics. However, its lack of environmental stability severely limits its synthesis and processing. Here we demonstrate that high-quality, few-layer BP nanosheets, with controllable size and observable photoluminescence, can be produced in large quantities by liquid phase exfoliation under ambient conditions in solvents such as N-cyclohexyl-2-pyrrolidone (CHP). Nanosheets are surprisingly stable in CHP, probably due to the solvation shell protecting the nanosheets from reacting with water or oxygen. Experiments, supported by simulations, show reactions to occur only at the nanosheet edge, with the rate and extent of the reaction dependent on the water/oxygen content. We demonstrate that liquid-exfoliated BP nanosheets are potentially useful in a range of applications from ultrafast saturable absorbers to gas sensors to fillers for composite reinforcement. PMID:26469634

  8. Desmosomes: interconnected calcium-dependent structures of remarkable stability with significant integral membrane protein turnover.

    Science.gov (United States)

    Windoffer, Reinhard; Borchert-Stuhlträger, Monika; Leube, Rudolf E

    2002-04-15

    Desmosomes are prominent cell adhesion structures that are major stabilizing elements, together with the attached cytoskeletal intermediate filament network, of the cytokeratin type in epithelial tissues. To examine desmosome dynamics in tightly coupled cells and in situations of decreased adhesion, fluorescent desmosomal cadherin desmocollin 2a (Dsc2a) chimeras were stably expressed in human hepatocellular carcinoma-derived PLC cells (clone PDc-13) and in Madin-Darby canine kidney cells (clone MDc-2) for the continuous monitoring of desmosomes in living cells. The hybrid polypeptides integrated specifically and without disturbance into normal-appearing desmosomes that occurred in association with typical cytokeratin filament bundles. Tracking of labeled adhesion sites throughout the cell cycle by time-lapse fluorescence microscopy revealed that they were immobile and that they maintained their structural integrity for long periods of time. Time-space diagrams further showed that desmosomal positioning was tightly controlled, even during pronounced cell shape changes, although the desmosomal arrays extended and contracted, suggesting that they were interconnected by a flexible system with intrinsic elasticity. Double-fluorescence microscopy detecting Dsc2a chimeras together with fluorescent cytokeratin 18 chimeras revealed the association and synchronous movement of labeled desmosomes and fluorescent cytokeratin filaments. Only a minor destabilization of desmosomes was observed during mitosis, demonstrated by increased diffuse plasma membrane fluorescence and the fusion of desmosomes into larger structures. Desmosomes did not disappear completely at any time in any cell, and residual cytokeratin filaments remained in association with adhesion sites throughout cell division. On the other hand, a rapid loss of desmosomes was observed upon calcium depletion, with irreversible uptake of some desmosomal particles. Simultaneously, diffusely distributed desmosomal

  9. Ether modified poly(ether ether ketone) nonwoven membrane with excellent wettability and stability as a lithium ion battery separator

    Science.gov (United States)

    Li, Zhen; Wang, Wenqiang; Han, Yu; Zhang, Lei; Li, Shuangshou; Tang, Bin; Xu, Shengming; Xu, Zhenghe

    2018-02-01

    In this study, poly(ether ether ketone) is first chloromethylated to improve the solubility and is later used for nonwoven membrane fabrication by electrospinning. Finally, the chloromethyl group was converted to the ethyl ether group and dibenzyl ether group in a hot alkaline solution. The abundant polar groups endow the membrane with excellent wettability, reducing the contact angle to 0°. The polymer matrix is crosslinked by dibenzyl ether group, endowing the membrane with excellent stability (insolubility in many solvents, and ultra-low swelling in the electrolyte at 80 °C) and good anti-shrinkage property (0% at 180 °C). The electrospinning-fabricated membrane remains stable until 4.812 V (vs. Li+/Li), meeting the requirement for use in lithium ion batteries. The interwoven structure of the nonwoven membrane effectively gives rise to the high electrolyte uptake of 215.8%. The ionic conductivity of the electrolyte-swelled electrospinning-fabricated membrane is 51% higher than that of the electrolyte-swelled Celgard membrane. As a result, the lithium ion battery with this nonwoven membrane exhibits an enhanced rate performance (up to 42.5% higher than the lithium ion battery with a PP separator) and satisfactory cycling performance.

  10. On Stabilization of PVPA/PVA Electrospun Nanofiber Membrane and Its Effect on Material Properties and Biocompatibility

    Directory of Open Access Journals (Sweden)

    Rose Ann Franco

    2012-01-01

    Full Text Available A novel nanofiber membrane was fabricated by electrospinning composed of polyvinyl phosphonic acid (PVPA and polyvinyl alcohol (PVA. Stabilization was done due to the high dissolvability of the membrane when in contact with water. Physical treatment was done by exposure to heat at 150°C in a vacuum environment at different periods of time. Chemical crosslinking was done by immersion in methanol and methanol/ glutaraldehyde. A heat-exposed membrane was also further crosslinked chemically. All conditions were compared with regards to its effect on the material properties of the membranes and its biological response in vitro with MG-63 osteoblast-like cell line. Visual examination and dimensional analyses showed that heat treatment produced discoloration on the membrane surface and chemical crosslinking reduced membrane dimensions. Tensile strength and strain improved in crosslinked membranes compared to noncrosslinked counterpart. Swelling and degradation was also investigated and was seen to vary depending on the crosslinking condition. Biocompatibility was observed to be more favorable in heat-treated membranes.

  11. Molecular Simulation of Ionic Polyimides and Composites with Ionic Liquids as Gas-Separation Membranes.

    Science.gov (United States)

    Abedini, Asghar; Crabtree, Ellis; Bara, Jason E; Turner, C Heath

    2017-10-24

    Polyimides are at the forefront of advanced membrane materials for CO 2 capture and gas-purification processes. Recently, ionic polyimides (i-PIs) have been reported as a new class of condensation polymers that combine structural components of both ionic liquids (ILs) and polyimides through covalent linkages. In this study, we report CO 2 and CH 4 adsorption and structural analyses of an i-PI and an i-PI + IL composite containing [C 4 mim][Tf 2 N]. The combination of molecular dynamics (MD) and grand canonical Monte Carlo (GCMC) simulations is used to compute the gas solubility and the adsorption performance with respect to the density, fractional free volume (FFV), and surface area of the materials. Our results highlight the polymer relaxation process and its correlation to the gas solubility. In particular, the surface area can provide meaningful guidance with respect to the gas solubility, and it tends to be a more sensitive indicator of the adsorption behavior versus only considering the system density and FFV. For instance, as the polymer continues to relax, the density, FFV, and pore-size distribution remain constant while the surface area can continue to increase, enabling more adsorption. Structural analyses are also conducted to identify the nature of the gas adsorption once the ionic liquid is added to the polymer. The presence of the IL significantly displaces the CO 2 molecules from the ligand nitrogen sites in the neat i-PI to the imidazolium rings in the i-PI + IL composite. However, the CH 4 molecules move from the imidazolium ring sites in the neat i-PI to the ligand nitrogen atoms in the i-PI + IL composite. These molecular details can provide critical information for the experimental design of highly selective i-PI materials as well as provide additional guidance for the interpretation of the simulated adsorption systems.

  12. Operation of a breadboard liquid-sorbent/membrane-contactor system for removing carbon dioxide and water vapor from air

    Science.gov (United States)

    Mccray, Scott B.; Ray, Rod; Newbold, David D.; Millard, Douglas L.; Friesen, Dwayne T.; Foerg, Sandra

    1992-01-01

    Processes to remove and recover carbon dioxide (CO2) and water vapor from air are essential for successful long-duration space missions. This paper presents results of a developmental program focused on the use of a liquid-sorbent/membrane-contactor (LSMC) system for removal of CO2 and water vapor from air. In this system, air from the spacecraft cabin atmosphere is circulated through one side of a hollow-fiber membrane contactor. On the other side of the membrane contactor is flowed a liquid sorbent, which absorbs the CO2 and water vapor from the feed air. The liquid sorbent is then heated to desorb the CO2 and water vapor. The CO2 is subsequently removed from the system as a concentrated gas stream, whereas the water vapor is condensed, producing a water stream. A breadboard system based on this technology was designed and constructed. Tests showed that the LSMC breadboard system can produce a CO2 stream and a liquid-water stream. Details are presented on the operation of the system, as well as the effects on performance of variations in feed conditions.

  13. An Untrodden Path: Versatile Fabrication of Self-Supporting Polymer-Stabilized Percolation Membranes (PSPMs) for Gas Separation.

    Science.gov (United States)

    Friebe, Sebastian; Mundstock, Alexander; Schneider, Daniel; Caro, Jürgen

    2017-05-11

    The preparation and scalability of zeolite or metal organic framework (MOF) membranes remains a major challenge, and thus prevents the application of these materials in large-scale gas separation. Additionally, several zeolite or MOF materials are quite difficult or nearly impossible to grow as defect-free layers, and require expensive macroporous ceramic or polymer supports. Here, we present new self-supporting zeolite and MOF composite membranes, called Polymer-Stabilized Percolation Membranes (PSPMs), consisting of a pressed gas selective percolation network (in our case ZIF-8, NaX and MIL-140) and a gas-impermeable infiltrated epoxy resin for cohesion. We demonstrate the performance of these PSPMs by separating binary mixtures of H 2 /CO 2 and H 2 /CH 4 . We report the brickwork-like architecture featuring selective percolation pathways and the polymer as a stabilizer, compare the mechanical stability of said membranes with competing materials, and give an outlook on how economic these membranes may become. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Stability and kinetic studies of supported ionic liquid phase catalysts for hydroformylation of propene

    DEFF Research Database (Denmark)

    Riisager, Anders; Fehrmann, Rasmus; Haumann, Marco

    2005-01-01

    . The activation energy was determined to be 63.3 +/- 2.1 kJ mol(-1), which is in good agreement with known results from biphasic hydroformylation. The results from the kinetic studies confirmed previously published results on the homogeneous nature of the heterogenised Rh-SILP catalyst. Long-term stability......Supported ionic liquid phase (SILP) catalysts have been studied with regard to their long-term stability in the continuous gas-phase hydroformylation of propene. Kinetic data have been acquired by variation of temperature, pressure, syngas composition, substrate concentration, and residence time...... exceeded 200 h time on stream with no loss in selectivity. A small decrease in activity could be compensated by a vacuum procedure regaining the initial activity....

  15. Performance of Hollow Fiber Membrane Gas-Liquid Contactors to Absorb CO2 Using Diethanolamine (Dea as a Solvent

    Directory of Open Access Journals (Sweden)

    Sutrasno Kartohardjono

    2010-10-01

    Full Text Available This study uses DEA solution to absorb CO2 from the gas flow through the hollow fiber membrane contactors. This study aims to evaluate the performance of hollow fiber membrane contactors to absorb CO2 gas using DEA solution as solvent through mass transfer and hydrodynamics studies. The use of DEA solution is to reduce the mass transfer resistance in the liquid phase, and on the other side, the large contact area of the membrane surface can cover the disadvantage of membrane contactors; additional mass transfer resistance in the membrane phase. During experiments, CO2 feed flows through the fiber lumens, while the 0.01 M DEA solution flows in the shell side of membrane contactors. Experimental results show that the mass transfer coefficients and fluxes of CO2 increase with an increase in both water and DEA solution flow rates. Increasing the amount of fibers in the contactors will decrease the mass transfer and fluxes at the same DEA solution flow rate. Mass transfer coefficients and CO2 fluxes using DEA solution can achieve 28,000 and 7.6 million times greater than using water as solvent, respectively. Hydrodynamics studies show that the liquid pressure drops in the contactors increase with increasing liquid flow rate and number of fibers in the contactors. The friction between water and the fibers in the contactor was more pronounced at lower velocities, and therefore, the value of the friction factor is also higher at lower velocities.

  16. Oxygen permeation and thermo-chemical stability of oxygen separation membrane materials for the oxyfuel process

    Energy Technology Data Exchange (ETDEWEB)

    Ellett, Anna Judith

    2009-07-01

    analysis (TGA) and thermo mechanical analysis (TMA). An increase in thermal expansion and oxygen permeation associated with an increase in oxygen vacancy concentration, observed also in the TGA curves, occurs during heating. BSCF50 exhibits permeation fluxes well above those of LSCF58, PSCF58 and La{sub 2}NiO{sub 4+{delta}}, which are quite similar to each other. After exposure, no degradation of LSCF58, La{sub 2}NiO{sub 4+{delta}} and PSCF58 occurs. On the other hand BSCF50 is found to be unstable in CO{sub 2}- and/or H{sub 2}O-containing atmospheres and also to exhibit a chemical demixing. The thermo-chemical stability and the oxygen permeation performances are both crucial factors in the selection of high purity oxygen separation membranes for the oxyfuel process, thus making LSCF58, PSCF58 and La{sub 2}NiO{sub 4+{delta}} in this study the most suitable materials for this application. Serious issues arise, however, from the fact that secondary non-ion conducting oxide phases are formed in the bulk of every material, forming obstacles for oxygen ion migration, and also that a reaction with chromia occurs, preventing their use without protection. (orig.)

  17. The Tat System for Membrane Translocation of Folded Proteins Recruits the Membrane-stabilizing Psp Machinery in Escherichia coli*

    Science.gov (United States)

    Mehner, Denise; Osadnik, Hendrik; Lünsdorf, Heinrich; Brüser, Thomas

    2012-01-01

    Tat systems transport folded proteins across energized membranes of bacteria, archaea, and plant plastids. In Escherichia coli, TatBC complexes recognize the transported proteins, and TatA complexes are recruited to facilitate transport. We achieved an abstraction of TatA from membranes without use of detergents and observed a co-purification of PspA, a membrane-stress response protein. The N-terminal transmembrane domain of TatA was required for the interaction. Electron microscopy displayed TatA complexes in direct contact with PspA. PspB and PspC were important for the TatA-PspA contact. The activator protein PspF was not involved in the PspA-TatA interaction, demonstrating that basal levels of PspA already interact with TatA. Elevated TatA levels caused membrane stress that induced a strictly PspBC- and PspF-dependent up-regulation of PspA. TatA complexes were found to destabilize membranes under these conditions. At native TatA levels, PspA deficiency clearly affected anaerobic TMAO respiratory growth, suggesting that energetic costs for transport of large Tat substrates such as TMAO reductase can become growth limiting in the absence of PspA. The physiological role of PspA recruitment to TatA may therefore be the control of membrane stress at active translocons. PMID:22689583

  18. Understanding structure-stability relationships of Candida antartica lipase B in ionic liquids.

    Science.gov (United States)

    De Diego, Teresa; Lozano, Pedro; Gmouh, Said; Vaultier, Michel; Iborra, José L

    2005-01-01

    Two different water-immiscible ionic liquids (ILs), 1-ethyl-3-methylimidizolium bis(trifluoromethylsulfonyl)imide and butyltrimethylammonium bis(trifluoromethylsulfonyl)imide, were used for butyl butyrate synthesis from vinyl butyrate catalyzed by Candida antarctica lipase B (CALB) at 2% (v/v) water content and 50 degrees C. Both the synthetic activity and stability of the enzyme in these ILs were enhanced as compared to those in hexane. Circular dichroism and intrinsic fluorescence spectroscopic techniques have been used over a period of 4 days to determine structural changes in the enzyme associated with differences in its stability for each assayed medium. CALB showed a loss in residual activity higher than 75% after 4 days of incubation in both water and hexane media at 50 degrees C, being related to great changes in both alpha-helix and beta-strand secondary structures. The stabilization of CALB, which was observed in the two ILs studied, was associated with both the maintenance of the 50% of initial alpha-helix content and the enhancement of beta-strands. Furthermore, intrinsic fluorescence studies clearly showed how a classical enzyme unfolding was occurring with time in both water and hexane media. However, the structural changes associated with the incubation of the enzyme in both ILs might be attributed to a compact and active enzyme conformation, resulting in an enhancement of the stability in these nonaqueous environments.

  19. Stabilization of enzymes in ionic liquids via modification of enzyme charge.

    Science.gov (United States)

    Nordwald, Erik M; Kaar, Joel L

    2013-09-01

    Due to the propensity of ionic liquids (ILs) to inactivate enzymes, the development of strategies to improve enzyme utility in these solvents is critical to fully exploit ILs for biocatalysis. We have developed a strategy to broadly improve enzyme utility in ILs based on elucidating the effect of charge modifications on the function of enzymes in IL environments. Results of stability studies in aqueous-IL mixtures indicated a clear connection between the ratio of enzyme-containing positive-to-negative sites and enzyme stability in ILs. Stability studies of the effect of [BMIM][Cl] and [EMIM][EtSO4 ] on chymotrypsin specifically found an optimum ratio of positively-charged amine-to-negatively-charged acid groups (0.39). At this ratio, the half-life of chymotrypsin was increased 1.6- and 4.3-fold relative to wild-type chymotrypsin in [BMIM][Cl] and [EMIM][EtSO4 ], respectively. The half-lives of lipase and papain were similarly increased as much as 4.0 and 2.4-fold, respectively, in [BMIM][Cl] by modifying the ratio of positive-to-negative sites of each enzyme. More generally, the results of stability studies found that modifications that reduce the ratio of enzyme-containing positive-to-negative sites improve enzyme stability in ILs. Understanding the impact of charge modification on enzyme stability in ILs may ultimately be exploited to rationally engineer enzymes for improved function in IL environments. Copyright © 2013 Wiley Periodicals, Inc.

  20. Optimization of cyanide extraction from wastewater using emulsion liquid membrane system by response surface methodology.

    Science.gov (United States)

    Xue, Juan Qin; Liu, Ni Na; Li, Guo Ping; Dang, Long Tao

    To solve the disposal problem of cyanide wastewater, removal of cyanide from wastewater using a water-in-oil emulsion type of emulsion liquid membrane (ELM) was studied in this work. Specifically, the effects of surfactant Span-80, carrier trioctylamine (TOA), stripping agent NaOH solution and the emulsion-to-external-phase-volume ratio on removal of cyanide were investigated. Removal of total cyanide was determined using the silver nitrate titration method. Regression analysis and optimization of the conditions were conducted using the Design-Expert software and response surface methodology (RSM). The actual cyanide removals and the removals predicted using RSM analysis were in close agreement, and the optimal conditions were determined to be as follows: the volume fraction of Span-80, 4% (v/v); the volume fraction of TOA, 4% (v/v); the concentration of NaOH, 1% (w/v); and the emulsion-to-external-phase volume ratio, 1:7. Under the optimum conditions, the removal of total cyanide was 95.07%, and the RSM predicted removal was 94.90%, with a small exception. The treatment of cyanide wastewater using an ELM is an effective technique for application in industry.

  1. DEVELOPMENT AND SELECTION OF IONIC LIQUID ELECTROLYTES FOR HYDROXIDE CONDUCTING POLYBENZIMIDAZOLE MEMBRANES IN ALKALINE FUEL CELLS

    Energy Technology Data Exchange (ETDEWEB)

    Fox, E.

    2012-05-01

    Alkaline fuel cell (AFC) operation is currently limited to specialty applications such as low temperatures and pure HO due to the corrosive nature of the electrolyte and formation of carbonates. AFCs are the cheapest and potentially most efficient (approaching 70%) fuel cells. The fact that non-Pt catalysts can be used, makes them an ideal low cost alternative for power production. The anode and cathode are separated by and solid electrolyte or alkaline porous media saturated with KOH. However, CO from the atmosphere or fuel feed severely poisons the electrolyte by forming insoluble carbonates. The corrosivity of KOH (electrolyte) limits operating temperatures to no more than 80°C. This chapter examines the development of ionic liquids electrolytes that are less corrosive, have higher operating temperatures, do not chemically bond to CO and enable alternative fuels. Work is detailed on the IL selection and characterization as well as casting methods within the polybenzimidazole based solid membrane. This approach is novel as it targets the root of the problem (the electrolyte) unlike other current work in alkaline fuel cells which focus on making the fuel cell components more durable.

  2. Engineering development of ceramic membrane reactor system for converting natural gas to hydrogen and synthesis gas for liquid transportation fuels

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    The objective of this contract is to research, develop and demonstrate a novel ceramic membrane reactor system for the low-cost conversion of natural gas to synthesis gas and hydrogen for liquid transportation fuels: the ITM Syngas process. Through an eight-year, three-phase program, the technology will be developed and scaled up to obtain the technical, engineering, operating and economic data necessary for the final step to full commercialization of the Gas-to-Liquids (GTL) conversion technology. This report is a summary of activities through April 1998.

  3. Cell membrane thermo-stability studies through joint segregation analysis in various wheat populations

    International Nuclear Information System (INIS)

    Ullah, K.; Khan, N.U.; Gul, S.; Khan, S.J.

    2014-01-01

    Using joint segregation analysis (JSA) technique as statistical approach, mixed inheritance analysis for cell plasma membrane as membrane thermal stability (MTS) was assayed in two parental lines (P1, P2) and their four populations (F1, BC1, BC2, F2) of four wheat crosses, viz., Hashim-08 * LU-26, Farid-06 * Shafaq, Parula * Blue Silver and TD-1 * D-97603 at Faculty of Agriculture, Gomal University, Dera Ismail Khan, Pakistan during crop season 2011-12. Results revealed that MTS was under control of two mixed groups of genes i.e., additive-dominant-epistatic major genes plus additive-dominant-epistasis of polygenes (model E) in Hashim-08 * LU-26 and Farid-06 * Shafaq crosses, respectively. In cross Parula * Blue Silver, it was governed by mixed genes i.e. one major-gene and additive-dominance-epistatic polygenes (model D). However, in cross TD-1 * D-97603, the MTS was under the influence of mixed epistasis of two major genes plus polygenes (model E-1). Polygene variation and polygene heritability were higher than major gene variation and heritability in crosses Hashim-08 * LU-26 and Farid-06 * Shafaq. In crosses Parula * Blue Silver and TD-1 * D-97603, the major gene variation and heritability were higher than polygene variation and heritability, indicating maximum contribution of the major genes. While in cross TD-1 * D-97603, epistatic components were also positive and due to which the polygene heritability was almost zero. Moderate to high environmental variation in the MTS for segregating generations revealed that the said trait was highly persuaded by the environment. However, the genetic behavior of the MTS suggested that early selection for MTS in the crosses Hashim-08 * LU-26 and Farid-06 * Shafaq would be efficient. Whereas, the delayed selection in crosses Parula * Blue Silver and TD-1 * D-97603 until the accumulation of maximum favorable genes will be effective. (author)

  4. Potentiometric sensing of iodide using polymeric membranes of microwave stabilized β-AgI

    International Nuclear Information System (INIS)

    James, Dhanya; Rao, T. Prasada

    2012-01-01

    Highlights: ► Stable β-phase was obtained by post MW irradiation of AgI precipitate. ► Constructed ISEby dispersing stable β-AgI crystals in polyvinyl chloride. ► Designed iodide ISE exhibited wide linear range and fast response. ► Highly selective with selectivity factors less than 10 −6 . ► Successfully applied to natural waters, table salt and human urine samples. - Abstract: A polymer based heterogeneous ion selective electrode (ISE) membrane was fabricated for the potentiometric sensing of iodide. The sensing element used for the preparation of the ISE membrane was microwave stabilized β-AgI. Because microwave energy was found to be beneficial for causing hysteresis at the phase transition temperature of AgI, an attempt has been made to prepare stable and conductive β-AgI crystals by post microwave irradiation under high pressure. A conventionally precipitated AgI based ISE was also fabricated for comparative studies. The β-AgI based ISE could respond to a wide range of iodide concentrations (1 × 10 −8 to 1 M) within 60 s with a detection limit of 10 nM. The ISE gave stable response to iodide ions in a pH range of 2.0–8.0 and was highly selective in the presence of various interfering ions. The performance of the proposed iodide ISE in the analysis of natural and seawater samples was encouraging, and the determination of iodide in table salt and human urine samples was explained using the developed sensor.

  5. Modulated growth, stability and interactions of liquid-like coacervate assemblies of elastin.

    Science.gov (United States)

    Muiznieks, Lisa D; Cirulis, Judith T; van der Horst, Astrid; Reinhardt, Dieter P; Wuite, Gijs J L; Pomès, Régis; Keeley, Fred W

    2014-06-01

    Elastin self-assembles from monomers into polymer networks that display elasticity and resilience. The first major step in assembly is a liquid-liquid phase separation known as coacervation. This process represents a continuum of stages from initial phase separation to early growth of droplets by coalescence and later "maturation" leading to fiber formation. Assembly of tropoelastin-rich globules is on pathway for fiber formation in vivo. However, little is known about these intermediates beyond their size distribution. Here we investigate the contribution of sequence and structural motifs from full-length tropoelastin and a set of elastin-like polypeptides to the maturation of coacervate assemblies, observing their growth, stability and interaction behavior, and polypeptide alignment within matured globules. We conclude that maturation is driven by surface properties, leading to stabilization of the interface between the hydrophobic interior and aqueous solvent, potentially through structural motifs, and discuss implications for droplet interactions in fiber formation. Copyright © 2014. Published by Elsevier B.V.

  6. Collagen films with stabilized liquid crystalline phases and concerns on osteoblast behaviors

    International Nuclear Information System (INIS)

    Tang, Minjian; Ding, Shan; Min, Xiang; Jiao, Yanpeng; Li, Lihua; Li, Hong; Zhou, Changren

    2016-01-01

    To duplicate collagen's in vivo liquid crystalline (LC) phase and investigate the relationship between the morphology of LC collagen and osteoblast behavior, a self-assembly method was introduced for preparing collagen films with a stabilized LC phase. The LC texture and topological structure of the films before and after stabilization were observed with polarizing optical microscopy, scanning electron microscopy (SEM), and atomic force microscopy (AFM). The relationship between the collagen films and osteoblast behavior was studied with the 3-(4,5)-dimethylthiahiazo(-z-y1)-3,5-di-phenytetrazoliumromide method, proliferation index detection, alkaline phosphatase measurements, osteocalcin assay, inverted microscopy, SEM observation, AFM observation, and cytoskeleton fluorescence staining. The results showed that the LC collagen film had continuously twisting orientations in the cholesteric phase with a typical series of arced patterns. The collagen fibers assembled in a well-organized orientation in the LC film. Compared to the non-LC film, the LC collagen film can promote cell proliferation, and increase ALP and osteocalcin expression, revealing a contact guide effect on osteoblasts. - Highlights: • Collagen film with liquid crystalline (LC) phase was observed by POM, SEM and AFM. • The effect of LC collagen film on osteoblasts behaviors was studied in detail. • LC collagen film promoted osteoblast proliferation and osteogenesis activity.

  7. Polymer-Stabilized Micropixelated Liquid Crystals with Tunable Optical Properties Fabricated by Double Templating.

    Science.gov (United States)

    Sasaki, Yuji; Ueda, Motoshi; Le, Khoa V; Amano, Reo; Sakane, Shin; Fujii, Shuji; Araoka, Fumito; Orihara, Hiroshi

    2017-10-01

    Self-organized nano- and microstructures of soft materials are attracting considerable attention because most of them are stimuli-responsive due to their soft nature. In this regard, topological defects in liquid crystals (LCs) are promising not only for self-assembling colloids and molecules but also for electro-optical applications such as optical vortex generation. However, there are currently few bottom-up methods for patterning a large number of defects periodically over a large area. It would be highly desirable to develop more effective techniques for high-throughput and low-cost fabrication. Here, a micropixelated LC structure consisting of a square array of topological defects is stabilized by photopolymerization. A polymer network is formed on the structure of a self-organized template of a nematic liquid crystal (NLC), and this in turn imprints other nonpolymerizable NLC molecules, which maintains their responses to electric field and temperature. Photocuring of specific local regions is used to create a designable template for the reproducible self-organization of defects. Moreover, a highly diluted polymer network (≈0.1 wt% monomer) exhibits instant on-off switching of the patterns. Beyond the mere stabilization of patterns, these results demonstrate that the incorporation of self-organized NLC patterns offers some unique and unconventional applications for anisotropic polymer networks. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Stability of alprazolam, chloroquine phosphate, cisapride, enalapril maleate, and hydralazine hydrochloride in extemporaneously compounded oral liquids.

    Science.gov (United States)

    Allen, L V; Erickson, M A

    1998-09-15

    The stability of five drugs commonly prescribed for use in oral liquid dosage forms but not commercially available as such was studied. Alprazolam 1 mg/mL, chloroquine phosphate 15 mg/mL, cisapride 1 mg/mL, enalapril maleate 1 mg/mL, and hydralazine hydrochloride 4 mg/mL were each prepared in a 1:1 mixture of Ora-Sweet and Ora-Plus (Paddock Laboratories), a 1:1 mixture of Ora-Sweet SF and Ora-Plus, and cherry syrup and placed in 120-mL amber clear polyethylene terephthalate bottles. Three bottles of each liquid were stored at 5 degrees C and three at 25 degrees C, all in the dark. Samples were taken initially and at various times up to 60 days for analysis by high-performance liquid chromatography and assessment of appearance and odor; pH was measured. A mean of at least 91% of the initial drug concentration was retained for 60 days in the alprazolam, chloroquine phosphate, cisapride, and enalapril maleate liquids. The hydralazine hydrochloride liquids retained more than 90% of the initial concentration for only one day at 5 degrees C when prepared with Ora-Sweet-Ora-Plus and two days when prepared with Ora-Sweet SF-Ora-Plus and for less than a day in these preparations at 25 degrees C and in cherry syrup at 5 and 25 degrees C. No substantial changes in the appearance, odor, or pH of any liquid were observed. Alprazolam 1 mg/mL, chloroquine phosphate 15 mg/mL, cisapride 1 mg/mL, and enalapril maleate 1 mg/mL were stable in three extemporaneously compounded oral liquids for 60 days at 5 and 25 degrees C; hydralazine hydrochloride 4 mg/mL was stable at 5 degrees C for one day in Ora-Sweet-Ora Plus and for two days in Ora-Sweet SF-Ora-Plus.

  9. Permeabilitas Membran Transpor Campuran Unsur Tanah Jarang (La, Nd, Gd, Lu Menggunakan Carrier (TBP : D2EHPA Melalui Supported Liquid Membrane

    Directory of Open Access Journals (Sweden)

    Djabal Nur Basir

    2015-01-01

    Full Text Available Methods that have been developed currently for the separation and purification of rare earth elements, REE’s are solvent extraction by through immobilization of an extracting agent in a porous polymeric membrane. This methods beside could increase the transport selectivity, also the amount of carrier was very few. This technique is known as supported liquid membrane, SLM. Research toward transport and separation of REE’s through SLM have been still relatively limited merely to single feed-binary mixture, and one type of carrier. The transport   membrane permeability was obtained in a mixture of REE’s (La,Nd,Gd,Lu using the carrier TBP : D2EHPA by SLM. In this SLM technique, supporting membrane PTFE (polytetrafluoroethylene was soaked in a mixture of TBP carrier (tributilfosfat as a neutral ligand and D2EHPA (acid-2- etilheksilfosfat as anionic ligand with a particular concentration ratio in the solvent kerosene as membrane phase. HCl as receiver phase and solution mixture of REE’s as feed phase. Determination of the REE’s total concentration was carried out by UV-Vis spectrophotometry with NAS (sodium alizarin sulfonate as the colouring agent at pH 4,75 and the solution absorbance was determinated at 534 nm as maximum wavelength. Transport patterns of REE’s on the variation of the concentration of total mixed carrier composition, pH, and concentration  of the receiver phase were done for 300 minutes. The optimum conditions of transport mixture of REE’s (La, Nd, Gd, Lu were feed phase pH 3,0; carrier TBP: D2EHPA (0,3:0,7 M; and receiver phase HCl 3,0 M. In this condition, the transport membrane permeability in mixture of REE’s was 0,1077 cm.menit-1 with the percent of transport was 95,24%.

  10. Liquid-liquid electro-organo-synthetic processes in a carbon nanofibre membrane microreactor: Triple phase boundary effects in the absence of intentionally added electrolyte

    International Nuclear Information System (INIS)

    Watkins, John D.; Ahn, Sunyhik D.; Taylor, James E.; Bull, Steven D.; Bulman-Page, Philip C.; Marken, Frank

    2011-01-01

    Graphical abstract: Display Omitted Highlights: → Amphiphilic carbon nanofiber membrane employed in electro-synthesis. → Triple phase boundary process within a carbon membrane. → Electrochemical deuteration in a liquid|liquid micro-reactor system. → Triple phase boundary reaction zone effects in electro-synthesis. - Abstract: An amphiphilic carbon nanofibre membrane electrode (ca. 50 nm fibre diameter, 50-100 μm membrane thickness) is employed as an active working electrode and separator between an aqueous electrolyte phase (with reference and counter electrode) and an immiscible organic acetonitrile phase (containing only the redox active material). Potential control is achieved with a reference and counter electrode located in the aqueous electrolyte phase, but the electrolysis is conducted in the organic acetonitrile phase in the absence of intentionally added supporting electrolyte. For the one-electron oxidation of n-butylferrocene coupled to perchlorate anion transfer from aqueous to organic phase effective electrolysis is demonstrated with an apparent mass transfer coefficient of m = 4 x 10 -5 m s -1 and electrolysis of typically 1 mg n-butylferrocene in a 100 μL volume. For the two-electron reduction of tetraethyl-ethylenetetracarboxylate the apparent mass transfer coefficient m = 4 x 10 -6 m s -1 is lower due to a less extended triple phase boundary reaction zone in the carbon nanofibre membrane. Nevertheless, effective electrolysis of up to 6 mg tetraethyl-ethylenetetracarboxylate in a 100 μL volume is demonstrated. Deuterated products are formed in the presence of D 2 O electrolyte media. The triple phase boundary dominated mechanism and future microreactor design improvements are discussed.

  11. Use of stable emulsion to improve stability, activity, and enantioselectivity of lipase immobilized in a membrane reactor.

    Science.gov (United States)

    Giorno, L; Li, N; Drioli, E

    2003-12-20

    The enantiocatalytic performance of immobilized lipase in an emulsion membrane reactor using stable emulsion prepared by membrane emulsification technology was studied. The production of optical pure (S)-naproxen from racemic naproxen methyl ester was used as a model reaction system. The O/W emulsion, containing the substrate in the organic phase, was fed to the enzyme membrane reactor from shell-to-lumen. The enzyme was immobilized in the sponge layer (shell side) of capillary polyamide membrane with 50 kDa cut-off. The aqueous phase was able to permeate through the membrane while the microemulsion was retained by the thin selective layer. Therefore, the substrate was kept in the enzyme-loaded membrane while the water-soluble product was continuously removed from the reaction site. The results show that lipase maintained stable activity during the entire operation time (more than 250 h), showing an enantiomeric excess (96 +/- 2%) comparable to the free enzyme (98 +/- 1%) and much higher compared to similar lipase-loaded membrane reactors used in two-separate phase systems (90%). The results demonstrate that immobilized enzymes can achieve high stability as well as high catalytic activity and enantioselectivity. Copyright 2003 Wiley Periodicals, Inc.

  12. Facilitated Transport of Zn2+, Ni2+ and Co2+ by Liquid Membrane Using a Tertio Amine as Carrier

    Directory of Open Access Journals (Sweden)

    Hassaine-Sadi F.

    2013-04-01

    Full Text Available The environmental impact of the emissions of heavy metals (Zn2+, Ni2+, Co2+ present in the industrial effluents become extensive more and more. The discharge of toxic metals into environment is a serious problem facing numerous industries. So the search for extraction techniques to remove those heavy metals are increasing interest. Liquid membranes have shown great potentiel in this way especially in cases where metal concentrations are relatively low and other techniques cannot be applied efficiently.The fundamental parameters influencing the transport of the zinc (II, nickel (II and cobalt (II through the liquid membrane have been examined (the acidity, the time of transport. The coupling that makes itself thanks to the membrane (extractant + diluent permits to define the different phases of transfer and to determine the mechanisms of transportation membranaires. In thi study of th facilitated transport of zinc, nickel, cobalt ions by liquid membranes containing Tri-n-octyl amine as carrier. The chemical variable exam permitted to determine the parameters giving the extraction efficiency and reextraction optimum. Some performances have been gotten so much to the level of the extraction that of the reextraction. A chemical modelization has allowed to identify the extraction mechanism and transport. The coupling required a real optimization of the set of the parameters. The symmetrical behavior of the two compartments showed that the extraction – reextraction association permits to achieve a transportation, one counter - transportation and a positive coupling. This lets predict an applications as well in the field of metalliferous processing liquid waste not very in charge as in that of the industrial wastes. This also allows an effective protection of the environment while being profitable.

  13. Fast Pyrolysis Oil Stabilization: An Integrated Catalytic and Membrane Approach for Improved Bio-oils. Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Huber, George W.; Upadhye, Aniruddha A.; Ford, David M.; Bhatia, Surita R.; Badger, Phillip C.

    2012-10-19

    This University of Massachusetts, Amherst project, "Fast Pyrolysis Oil Stabilization: An Integrated Catalytic and Membrane Approach for Improved Bio-oils" started on 1st February 2009 and finished on August 31st 2011. The project consisted following tasks: Task 1.0: Char Removal by Membrane Separation Technology The presence of char particles in the bio-oil causes problems in storage and end-use. Currently there is no well-established technology to remove char particles less than 10 micron in size. This study focused on the application of a liquid-phase microfiltration process to remove char particles from bio-oil down to slightly sub-micron levels. Tubular ceramic membranes of nominal pore sizes 0.5 and 0.8m were employed to carry out the microfiltration, which was conducted in the cross-flow mode at temperatures ranging from 38 to 45 C and at three different trans-membrane pressures varying from 1 to 3 bars. The results demonstrated the removal of the major quantity of char particles with a significant reduction in overall ash content of the bio-oil. The results clearly showed that the cake formation mechanism of fouling is predominant in this process. Task 2.0 Acid Removal by Membrane Separation Technology The feasibility of removing small organic acids from the aqueous fraction of fast pyrolysis bio-oils using nanofiltration (NF) and reverse osmosis (RO) membranes was studied. Experiments were carried out with a single solute solutions of acetic acid and glucose, binary solute solutions containing both acetic acid and glucose, and a model aqueous fraction of bio-oil (AFBO). Retention factors above 90% for glucose and below 0% for acetic acid were observed at feed pressures near 40 bar for single and binary solutions, so that their separation in the model AFBO was expected to be feasible. However, all of the membranes were irreversibly damaged when experiments were conducted with the model AFBO due to the presence of guaiacol in the feed solution. Experiments

  14. Deashing of coal liquids with ceramic membrane microfiltration and diafiltration. Final quarterly technical progress report, October 1--December 31, 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-12-31

    Diafiltration experiments were done to determine how much particulate- free oil could be extracted from the solids-containing stream. The 0. 05 {mu}m titania membrane was used for the concentration/diafiltration process runs at 270 C, 80 psig inlet pressure, and 6 gpm crossflow. Five concentration process runs were conducted. After the initial run, the concentrated material was diluted with hydrotreated start-up oil from the final solids back to 10% solids. The concentration was limited by increased pressure drop with increased solids content and plugged membrane module channels. Solids retention was greater than 99.5% for all samples. Attempts to clean membranes with solvent failed due to lack of time. Samples of the permeate and concentrate streams were taken for analysis; the diluent had a similar bp range to the coal liquids in the atmospheric bottoms; thus, distillation could not be used to separate the bottoms from the diluent.

  15. Lack of cations in flow cytometry buffers affect fluorescence signals by reducing membrane stability and viability of Escherichia coli strains.

    Science.gov (United States)

    Tomasek, Kathrin; Bergmiller, Tobias; Guet, Călin C

    2018-02-20

    Buffers are essential for diluting bacterial cultures for flow cytometry analysis in order to study bacterial physiology and gene expression parameters based on fluorescence signals. Using a variety of constitutively expressed fluorescent proteins in Escherichia coli K-12 strain MG1655, we found strong artifactual changes in fluorescence levels after dilution into the commonly used flow cytometry buffer phosphate-buffered saline (PBS) and two other buffer solutions, Tris-HCl and M9 salts. These changes appeared very rapidly after dilution, and were linked to increased membrane permeability and loss in cell viability. We observed buffer-related effects in several different E. coli strains, K-12, C and W, but not E. coli B, which can be partially explained by differences in lipopolysaccharide (LPS) and outer membrane composition. Supplementing the buffers with divalent cations responsible for outer membrane stability, Mg 2+ and Ca 2+ , preserved fluorescence signals, membrane integrity and viability of E. coli. Thus, stabilizing the bacterial outer membrane is essential for precise and unbiased measurements of fluorescence parameters using flow cytometry. Copyright © 2018 Elsevier B.V. All rights reserved.

  16. Analysis and quantification of parabens in cosmetic products by utilizing hollow fibre-supported liquid membrane and high performance liquid chromatography with ultraviolet detection.

    Science.gov (United States)

    Msagati, T A M; Barri, T; Larsson, N; Jönsson, J A

    2008-08-01

    A simple and direct method based on hollow fibre-supported liquid membrane (HFSLM) extraction and liquid chromatography equipped with a UV detector was developed for analysis and quantification of parabens in cosmetic products. The parabens analysed included methyl, ethyl, propyl, isobutyl and butyl paraben. The HFSLM extraction was carried out by employing di-n-hexyl ether as organic liquid that was immobilized in the hollow fibre membrane. The HFSLM extraction is simple, cheap, minimizes the use of solvents and uses disposable material. In an investigation of 11 paraben-containing cosmetic products, the levels of parabens (sum of all parabens in a product) ranged from 0.43% to 0.79% (w/w) for skin care products, 0.07-0.44% for hair fixing gels and 0.30-0.52% for soap solutions. The levels of individual parabens in individual cosmetic products ranged between 0.03% and 0.42% w/w for skin care products, 0.07% and 0.26% w/w for hair fixing gels and between 0.11% and 0.34% w/w for soap solutions. Parabens were found in the highest concentrations in skin care products followed by soap solutions and the least amounts were found in hair fixing gels. Of the paraben-containing products tested, all of them contained methyl paraben and about 90% contained propyl paraben in addition to methyl paraben. One product contained all the parabens analysed.

  17. Extraction and stability of bovine serum albumin (BSA) using cholinium-based Good's buffers ionic liquids.

    Science.gov (United States)

    Taha, Mohamed; Quental, Maria V; Correia, Isabel; Freire, Mara G; Coutinho, João A P

    2015-07-01

    Good's buffers ionic liquids (GB-ILs), composed of cholinium-based cations and Good's buffers anions, display self-buffering characteristics in the biological pH range, and their polarity and hydrophobicity can be easily tuned by a proper manipulation of their ions chemical structures. In this work, the extraction ability for bovine serum albumin (BSA) of aqueous biphasic systems (ABS) formed by polypropylene glycol 400 (PPG 400) and several GB-ILs was evaluated. ABS formed by PPG 400 and cholinium chloride ([Ch]Cl), GBs, and sucrose were also investigated for comparison purposes. It is shown that BSA preferentially migrates for the GB-IL-rich phase, with extraction efficiencies of 100%, achieved in a single-step. Dynamic light scattering, and circular dichroism (CD) and Fourier transform infrared (FTIR) spectroscopies were employed to evaluate the effect of the investigated cholinium-based GB-ILs on the BSA stability, and compared with results obtained for the respective GBs precursors, [Ch]Cl and sucrose, a well-known protein stabilizer. Molecular docking studies were also carried out to investigate on the binding sites of GB-IL ions to BSA. The experimental results confirm that BSA has a higher stability in GB-ILs than in any of the other compounds investigated.

  18. Stability-Indicating Assay for the Determination of Pentobarbital Sodium in Liquid Formulations

    Directory of Open Access Journals (Sweden)

    Myriam Ajemni

    2015-01-01

    Full Text Available A stability-indicating assay by reversed-phase high performance liquid chromatography (RP-HPLC method was developed for the determination of pentobarbital sodium in oral formulations: a drug used for infant sedation in computed tomography (CT or magnetic resonance imaging (MRI scan. The chromatographic separation was achieved on a reversed-phase C18 column, using isocratic elution and a detector set at 214 nm. The optimized mobile phase consisted of a 0.01 M potassium buffer pH 3 and methanol (40 : 60, v/v. The flow rate was 1.0 mL/min and the run time of analysis was 5 min. The linearity of the method was demonstrated in the range of 5 to 250 μg/mL pentobarbital sodium solution (r2 = 0.999. The limit of detection and limit of quantification were 2.10 and 3.97 μg/mL, respectively. The intraday and interday precisions were less than 2.1%. Accuracy of the method ranged from 99.2 to 101.3%. Stability studies indicate that the drug is stable to sunlight and in aqueous solution. Accelerated pentobarbital sodium breakdown by strong alkaline, acidic, or oxidative stress produced noninterfering peaks. This method allows accurate and reliable determination of pentobarbital sodium for drug stability assay in pharmaceutical studies.

  19. Novel Ceramic-Polymer Composite Membranes for the Separation of Hazardous Liquid Waste

    Energy Technology Data Exchange (ETDEWEB)

    Yoram Cohen

    2001-12-01

    The present project was conceived to address the need for robust yet selective membranes suitable for operating in harsh ph, solvent, and temperature environments. An important goal of the project was to develop a membrane chemical modification technology that would allow one to tailor-design membranes for targeted separation tasks. The method developed in the present study is based on the process of surface graft polymerization. Using essentially the same base technology of surface modification the research was aimed at demonstrating that improved membranes can be designed for both pervaporation separation and ultrafiltration. In the case of pervaporation, the present study was the first to demonstrate that pervaporation can be achieved with ceramic support membranes modified with an essentially molecular layer of terminally anchored polymer chains. The main advantage of the above approach, relative to other proposed membranes, is that the separating polymer layer is covalently attached to the ceramic support. Therefore, such membranes have a potential use in organic-organic separations where the polymer can swell significantly yet membrane robustness is maintained due to the chemical linkage of the chains to be inorganic support. The above membrane technology was also useful in developing fouling resistant ultrafiltration membranes. The prototype membrane developed in the project was evaluated for the treatment of oil-in-water microemulsions, demonstrating lack of irreversible fouling common with commercial membranes.

  20. Membrane Protein Stability Analyses by Means of Protein Energy Profiles in Case of Nephrogenic Diabetes Insipidus

    Directory of Open Access Journals (Sweden)

    Florian Heinke

    2012-01-01

    Full Text Available Diabetes insipidus (DI is a rare endocrine, inheritable disorder with low incidences in an estimated one per 25,000–30,000 live births. This disease is characterized by polyuria and compensatory polydypsia. The diverse underlying causes of DI can be central defects, in which no functional arginine vasopressin (AVP is released from the pituitary or can be a result of defects in the kidney (nephrogenic DI, NDI. NDI is a disorder in which patients are unable to concentrate their urine despite the presence of AVP. This antidiuretic hormone regulates the process of water reabsorption from the prourine that is formed in the kidney. It binds to its type-2 receptor (V2R in the kidney induces a cAMP-driven cascade, which leads to the insertion of aquaporin-2 water channels into the apical membrane. Mutations in the genes of V2R and aquaporin-2 often lead to NDI. We investigated a structure model of V2R in its bound and unbound state regarding protein stability using a novel protein energy profile approach. Furthermore, these techniques were applied to the wild-type and selected mutations of aquaporin-2. We show that our results correspond well to experimental water ux analysis, which confirms the applicability of our theoretical approach to equivalent problems.

  1. Performance Validation and Scaling of a Capillary Membrane Solid-Liquid Separation System

    Energy Technology Data Exchange (ETDEWEB)

    Rogers, S; Cook, J; Juratovac, J; Goodwillie, J; Burke, T

    2011-10-25

    Algaeventure Systems (AVS) has previously demonstrated an innovative technology for dewatering algae slurries that dramatically reduces energy consumption by utilizing surface physics and capillary action. Funded by a $6M ARPA-E award, transforming the original Harvesting, Dewatering and Drying (HDD) prototype machine into a commercially viable technology has required significant attention to material performance, integration of sensors and control systems, and especially addressing scaling issues that would allow processing extreme volumes of algal cultivation media/slurry. Decoupling the harvesting, dewatering and drying processes, and addressing the rate limiting steps for each of the individual steps has allowed for the development individual technologies that may be tailored to the specific needs of various cultivation systems. The primary performance metric used by AVS to assess the economic viability of its Solid-Liquid Separation (SLS) dewatering technology is algae mass production rate as a function of power consumption (cost), cake solids/moisture content, and solids capture efficiency. An associated secondary performance metric is algae mass loading rate which is dependent on hydraulic loading rate, area-specific hydraulic processing capacity (gpm/in2), filter:capillary belt contact area, and influent algae concentration. The system is capable of dewatering 4 g/L (0.4%) algae streams to solids concentrations up to 30% with capture efficiencies of 80+%, however mass production is highly dependent on average cell size (which determines filter mesh size and percent open area). This paper will present data detailing the scaling efforts to date. Characterization and performance data for novel membranes, as well as optimization of off-the-shelf filter materials will be examined. Third party validation from Ohio University on performance and operating cost, as well as design modification suggestions will be discussed. Extrapolation of current productivities

  2. Exploiting the Phenomenon of Liquid-Liquid Phase Separation for Enhanced and Sustained Membrane Transport of a Poorly Water-Soluble Drug.

    Science.gov (United States)

    Indulkar, Anura S; Gao, Yi; Raina, Shweta A; Zhang, Geoff G Z; Taylor, Lynne S

    2016-06-06

    Recent studies on aqueous supersaturated lipophilic drug solutions prepared by methods including antisolvent addition, pH swing, or dissolution of amorphous solid dispersions (ASDs) have demonstrated that when crystallization is slow, these systems undergo liquid-liquid phase separation (LLPS) when the concentration of the drug in the medium exceeds its amorphous solubility. Following LLPS, a metastable equilibrium is formed where the concentration of drug in the continuous phase corresponds to the amorphous solubility while the dispersed phase is composed of a nanosized drug-rich phase. It has been reasoned that the drug-rich phase may act as a reservoir, enabling the rate of passive transport of the drug across a membrane to be maintained at the maximum value for an extended period of time. Herein, using clotrimazole as a model drug, and a flow-through diffusion cell, the reservoir effect is demonstrated. Supersaturated clotrimazole solutions at concentrations below the amorphous solubility show a linear relationship between the maximum flux and the initial concentration. Once the concentration exceeds the amorphous solubility, the maximum flux achieved reaches a plateau. However, the duration for which the high flux persists was found to be highly dependent on the number of drug-rich nanodroplets present in the donor compartment. Macroscopic amorphous particles of clotrimazole did not lead to the same reservoir effect observed with the nanodroplets formed through the process of LLPS. A first-principles mathematical model was developed which was able to fit the experimental receiver concentration-time profiles for concentration regimes both below and above amorphous solubility, providing support for the contention that the nanodroplet phase does not directly diffuse across the membrane but, instead, rapidly replenishes the drug in the aqueous phase that has been removed by transport across the membrane. This study provides important insight into the properties of

  3. Physicochemical stability, microrheological properties and microstructure of lutein emulsions stabilized by multilayer membranes consisting of whey protein isolate, flaxseed gum and chitosan.

    Science.gov (United States)

    Xu, Duoxia; Aihemaiti, Zulipiya; Cao, Yanping; Teng, Chao; Li, Xiuting

    2016-07-01

    The impact of chitosan (CTS) on the physicochemical stability, microrheological property and microstructure of whey protein isolate (WPI)-flaxseed gum (FG) stabilized lutein emulsions at pH 3.0 was studied. A layer-by-layer electrostatic deposition method was used to prepare multilayered lutein emulsions. Droplet size, zeta-potential, instability index, microstructure and microrheological behavior of lutein emulsions were measured. The influences of interfacial layer, metal chelator and free radical scavenger on the chemical stability of lutein emulsions were also investigated. It was found that multilayer emulsions had better physical stability showing the pronounced effect of 1wt% CTS. The mean square displacement analysis demonstrated that CTS led to increases of macroscopic viscosity and elasticity index for WPI-FG stabilized lutein emulsions due to CTS embedding in the network. CTS also helped to chemically stabilize the lutein emulsions against degradation. The combination of interfacial membrane and prooxidative metal chelator or free radical scavenger was an effective method to control lutein degradation. Copyright © 2016 Elsevier Ltd. All rights reserved.

  4. Residue analysis of tetracyclines in milk by HPLC coupled with hollow fiber membranes-based dynamic liquid-liquid micro-extraction.

    Science.gov (United States)

    Xu, Hui; Mi, Hong-Yu; Guan, Ming-Ming; Shan, Hong-Yan; Fei, Qiang; Huan, Yan-Fu; Zhang, Zhi-Quan; Feng, Guo-Dong

    2017-10-01

    A novel hollow fiber membranes-based dynamic liquid-liquid micro-extraction (HF-DLLME) coupled with HPLC-UV detection has been developed for the residue analysis of tetracyclines in milk samples without deproteinization and degreasing. The influences of experimental parameters were investigated and optimized. The method showed a good performance. The limits of detection (LOD) are in the range of 0.95-3.6μg/L. The recoveries in spiked samples range from 92.38 to 107.3%. The relative standard deviations (RSDs) are lower than 8.66%. The advantages of this method are simple operation, high efficiency, absence of sample carryover and low cost. Copyright © 2017 Elsevier Ltd. All rights reserved.

  5. Liquid Marbles Stabilized by Fluorine-Bearing Cyclomatrix Polyphosphazene Particles and Their Application as High-Efficiency Miniature Reactors.

    Science.gov (United States)

    Wei, Wei; Lu, Rongjie; Ye, Weitao; Sun, Jianhua; Zhu, Ye; Luo, Jing; Liu, Xiaoya

    2016-02-23

    Increasing attention has been paid to fabricate multifunctional stabilizers of liquid marbles for expanding their application. Here, a kind of hydrophobic cyclomatrix polyphosphazene particles (PZAF) were facilely prepared using a one-step precipitation polycondensation of hexachlorocyclotriphosphazene and 4,4'-(hexafluoroisopropylidene)diphenol, and their ability to stabilize liquid marbles was first investigated. The Ag nanoparticle-decorated PZAF particles (Ag/PZAF) were then fabricated by an in situ reduction of silver nitrate onto PZAF particles and used to construct catalytic liquid marbles. The results revealed that the reduction of methylene blue (MB) in aqueous solution by sodium borohydride could be highly efficiently catalyzed in the catalytic liquid marbles, even with a large volume. An excellent cycle use performance of the catalytic liquid marbles without losing catalytic efficiency was also present. The high catalytic activity is mainly attributed to the uniform immobilization of Ag nanoparticles onto PZAF particles and the adsorption behavior of PZAF particles toward MB, which may play an effect on allowing high catalytic surface area and effective accelerating the mass transfer of MB to the Ag catalytic active sites, respectively. Therefore, the combination of Ag nanoparticles with PZAF particles has been demonstrated clearly to be a facile and effective strategy to obtain the functional stabilizer for preparing the catalytic liquid marbles as promising miniature reactors used in heterogeneous catalytic reactions.

  6. Stability Indicating Liquid Chromatographic Method for Simultaneous determination of Aspirin and Omeprazole.

    Science.gov (United States)

    Patel, Vandana B; Patel, Aishwarya D; Shah, Dimal A

    2017-10-23

    Aspirin combination is prescribed for the its thrombolytic activity where gastric ulceration is the major side effects of aspirin which can be prevented by combining it with proton pump inhibitor omeprazole. Present study describes development of analytical method for the estimation of aspirin and omeprazole in combination. Objective of the present study was to develop and validate chromatographic method for simultaneous analysis of aspirin and omeprazole. Isocratic, reversed phase stability indicating liquid chromatographic method was developed for the simultaneous determination of Aspirin and Omeprazole in combination. The separation was achieved on a Thermo Scientific Hypersil ODS (250 x 4.6 mm, 5 µm) column, kept at ambient temperature, using acetonitrile: methanol: 0.05 M phosphate buffer (40:5:55; pH 4 adjusted with 0.1% tri ethyl amine) as a mobile phase at a flow rate of 1 mL/min and UV detection was performed at 225 nm. The retention time was found to be 3.9 min for aspirin and 5.3 min for omeprazole. The method was oberved to be linear in the range of 2 - 80 μg/mL for aspirin and 1 - 40 μg/mL for omeprazole, respectively. The proposed method was validated as per ICH guidelines Q2 (R1). The developed RP- HPLC method was successfully applied for the simultaneous estimation of aspirin and omeprazole in the presence of degradation products of both the drugs. The present study describes liquid chromatographic method for the estimation of aspirin and omeprzole in combination. The method can be used for the analysis of stability samples and routine quality control samples. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

  7. Treatment of radioactive liquid effluents by reverse osmosis membranes: From lab-scale to pilot-scale.

    Science.gov (United States)

    Combernoux, Nicolas; Schrive, Luc; Labed, Véronique; Wyart, Yvan; Carretier, Emilie; Moulin, Philippe

    2017-10-15

    The recent use of the reverse osmosis (RO) process at the damaged Fukushima-Daiichi nuclear power plant generated a growing interest in the application of this process for decontamination purposes. This study focused on the development of a robust RO process for decontamination of two kinds of liquid effluents: a contaminated groundwater after a nuclear disaster and a contaminated seawater during a nuclear accident. The SW30 HR membrane was selected among other in this study due to higher retentions (96% for Cs and 98% for Sr) in a true groundwater. Significant fouling and scaling phenomenon, attributed to calcium and strontium precipitation, were evidenced in this work: this underscored the importance of the lab scale experiment in the process. Validation of the separation performances on trace radionuclides concentration was performed with similar retention around 96% between surrogates Cs (inactive) and 137 Cs (radioactive). The scale up to a 2.6 m 2 spiral wound membrane led to equivalent retentions (around 96% for Cs and 99% for Sr) but lower flux values: this underlined that the hydrodynamic parameters (flowrate/cross-flow velocity) should be optimized. This methodology was also applied on the reconstituted seawater effluent: retentions were slightly lower than for the groundwater and the same hydrodynamic effects were observed on the pilot scale. Then, ageing of the membrane through irradiation experiments were performed. Results showed that the membrane active layer composition influenced the membrane resistance towards γ irradiation: the SW30 HR membrane performances (retention and permeability) were better than the Osmonics SE at 1 MGy. Finally, to supplement the scale up approach, the irradiation of a spiral wound membrane revealed a limited effect on the permeability and retention. This indicated that irradiation conditions need to be controlled for a further development of the process. Copyright © 2017 Elsevier Ltd. All rights reserved.

  8. Kinetic stability and membrane structure of liposomes during in vitro infant intestinal digestion: Effect of cholesterol and lactoferrin.

    Science.gov (United States)

    Liu, Weilin; Wei, Fuqiang; Ye, Aiqian; Tian, Mengmeng; Han, Jianzhong

    2017-09-01

    The effects of cholesterol and lactoferrin on the kinetic stability and membrane structural integrity of negatively charged liposomes under in vitro infant intestinal digestion conditions were elucidated using dynamic light scattering, pH-stat titration, Fourier transform infrared spectroscopy, and pyrene steady state fluorescence probes. The liposomes had a smaller particle diameter, a wider size distribution, and a greater negative charge after digestion. The incorporation of cholesterol into the phospholipid bilayers resulted in a more ordered conformation in the aliphatic tail region and reduced micropolarity, indicating that cholesterol can improve the structural stability of liposomal membranes against intestinal environmental stress. Lactoferrin coverage facilitated the release of free fatty acids and increased the microfluidity of the bilayers, reducing the structural integrity of the liposomes. This study provides useful information on the design of liposomes and other microcapsules with improved and controlled release properties during digestion for particular groups of people. Copyright © 2017 Elsevier Ltd. All rights reserved.

  9. Development of a surfactant liquid membrane extraction process for the cleansing of industrial aqueous effluents containing metallic cation traces

    International Nuclear Information System (INIS)

    Rapaumbya Akaye, Guy-Roland

    1994-01-01

    The purpose of this work was to develop a process of surfactant liquid membrane extraction to purify industrial waste solution containing Cu(II), Fe(III), and Zn(II) (about 0,1 g/L). The extractant is the ammonium salt of Cyanex 306 and Aliquat 336. The first part of this work deals with the study of the liquid-liquid extraction of the metals. The efficiency of the extractant has been shown for the extraction of each metal alone and for Cu(II) and Zn(II) in the case of a mixture of the three metals. During this study we have observed that Fe(III) is reduced to Fe(II) (which is not extracted by the salt of Cyanex 301) in presence of Cu(II) and the quaternary ammonium salt (Aliquat 336). The optimisation of the experimental conditions for the discontinuous surfactant liquid membrane process led us to choose the following composition of the emulsion: 1,5 % of Cyanex 301 salt, 2,5 % of ECA 4360, dodecan. The internal phase is an aqueous solution containing 3,5 mol/L of NaOH and 0,5 mol/L tri-ethanolamin The residual concentration of Cu(II) and Zn(II) in the external phase is very low. In the case of iron, only 60 % are extracted because of the reduction phenomenon (10 % in liquid-liquid extraction). The realisation of the continuous process in pulsed column, after optimisation of hydrodynamics conditions, leads to similar results. In stationary conditions, we obtain a raffinate containing less than 0,5 mg/L of Cu(II) and Zn(II) and 36 mg/L of iron. The internal phase contains about 2 g/L of Cu(II) an Zn(II). We tried and minimize the reduction of Fe(III) in surfactant liquid membrane process. Less than 16 % of iron cannot be reduced. This leads to a purification of only 84 % In the basis of these results, processes of purification have been proposed for effluents of various composition. They enable to purify the effluent and besides to concentrate the pollutants about twenty times. (author) [fr

  10. Survival and growth of Salmonella Enteritidis in membrane processed liquid egg white with pH, temperature and storage conditions as controlling factors

    Science.gov (United States)

    A study was undertaken to determine the effect of variation in solution pH and process temperature on the removal and regrowth of Salmonella Enteritidis in liquid egg white (LEW) by microfiltration (MF) membrane process. Influence of various storage conditions on growth of Salmonella in membrane sep...

  11. Partial transient liquid phase diffusion bonding of Zircaloy-4 to stabilized austenitic stainless steel 321

    Energy Technology Data Exchange (ETDEWEB)

    Atabaki, M. Mazar, E-mail: m.mazaratabaki@gmail.com [Department of Materials Engineering, Faculty of Mechanical Engineering, University Technology Malaysia, 81310 (Malaysia); Hanzaei, A. Talebi [Department of Metallurgy and Materials Engineering, Faculty of Engineering, University of Tehran (Iran, Islamic Republic of)

    2010-10-15

    An innovative method was applied for bonding Zircaloy-4 to stabilized austenitic stainless steel 321 using an active titanium interlayer. Specimens were joined by a partial transient liquid phase diffusion bonding method in a vacuum furnace at different temperatures under 1 MPa dynamic pressure of contact. The influence of different bonding temperatures on the microstructure, microindentation hardness, joint strength and interlayer thickness has been studied. The diffusion of Fe, Cr, Ni and Zr has been investigated by scanning electron microscopy and energy dispersive spectroscopy elemental analyses. Results showed that control of the heating and cooling rate and 20 min soaking at 1223 K produces a perfect joint. However, solid-state diffusion of the melting point depressant elements into the joint metal causes the solid/liquid interface to advance until the joint is solidified. The tensile strength of all the bonded specimens was found around 480-670 MPa. Energy dispersive spectroscopy studies indicated that the melting occurred along the interface of the bonded specimens as a result of the transfer of atoms between the interlayer and the matrix during bonding. This technique provides a reliable method of bonding zirconium alloy to stainless steel.

  12. Application of mixed based membrane technology from component materials bintaro, zeolite and bentonite to reduction of songket waste liquid cloth

    Science.gov (United States)

    Dahlan, Muhammad Hatta; Saleh, Abdullah; Asip, Faisol; Makmun, Akbar; Defi

    2017-11-01

    Application of membrane technology based on clay mixture, Activated Carbon from Bintaro, Zeolite and Bentonit to process the waste water of Songket cloth is Palembang traditionally cloth. The applied research is into the superior field of industrial and household waste processing with membrane ceramic technology. The objective of this research is to design the liquid waste separation tool of jumputan cloth using better and simpler ceramic membrane so that it can help the artisans of Palembang songket or songket in processing the waste in accordance with the standard of environmental quality standard (BML) and Pergub Sumsel no. 16 in 2005. The specific target to be achieved can decrease the waste of cloth jumputan in accordance with applicable environmental quality standards the method used in achieving the objectives of this study using 2 processes namely the adsorption process using activated carbon and the separation process using a ceramic membrane based on the composition of the mixture. The activated carbon from bintaro seeds is expected to decrease the concentration of liquid waste of Songket cloth. Bintaro seeds are non-edible fruits where the composition contains organic ingredients that can absorb because contains dyes and filler metals. The process of membranization in the processing is expected to decrease the concentration of waste better and clear water that can be used as recycled water for household use. With the composition of a mixture of clay-based materials: zeolite, bentonit, activated carbon from bintaro seeds are expected Find the solution and get the novelty value in the form of patent in this research

  13. Polyethersulfone/Graphene Oxide Ultrafiltration Membranes from Solutions in Ionic Liquid

    KAUST Repository

    Mahalingam, Dinesh. K.

    2017-07-18

    Novel high flux polyethersulfone (PES) ultrafiltration membranes were fabricated by incorporating different amounts of graphene oxide (GO) sheets to PES as nanofillers. The membranes were prepared from solutions in 50/50 1-ethyl-3-methylimidazolium-diethylphosphate/N,N-dimethyl formamide. It was observed that the water permeance increased from 550 to 800 L m-2h-1bar-1, with incorporation of 1 wt% GO, keeping a molecular weight cut-off (MWCO) of approximately 32-34 kg mol-1. Cross-sectional scanning electron microscopy images of GO/PES membranes showed the formation of ultrathin selective layer unlike pristine membranes. Contact angle measurements confirmed the increase of hydrophilicity, by increasing the GO concentration. The rejection of humic acid and bovine serum albumin was demonstrated. The mechanical properties were improved, compared with the pristine membranes. The performance was just above the trade-off relationship between permeance and separation factor for PES membranes reported in the literature.

  14. Significant improvements in stability and reproducibility of atomic-scale atomic force microscopy in liquid

    International Nuclear Information System (INIS)

    Akrami, S M R; Nakayachi, H; Fukuma, T; Watanabe-Nakayama, T; Asakawa, H

    2014-01-01

    Recent advancement of dynamic-mode atomic force microscopy (AFM) for liquid-environment applications enabled atomic-scale studies on various interfacial phenomena. However, instabilities and poor reproducibility of the measurements often prevent systematic studies. To solve this problem, we have investigated the effect of various tip treatment methods for atomic-scale imaging and force measurements in liquid. The tested methods include Si coating, Ar plasma, Ar sputtering and UV/O 3 cleaning. We found that all the methods provide significant improvements in both the imaging and force measurements in spite of the tip transfer through the air. Among the methods, we found that the Si coating provides the best stability and reproducibility in the measurements. To understand the origin of the fouling resistance of the cleaned tip surface and the difference between the cleaning methods, we have investigated the tip surface properties by x-ray photoelectron spectroscopy and contact angle measurements. The results show that the contaminations adsorbed on the tip during the tip transfer through the air should desorb from the surface when it is immersed in aqueous solution due to the enhanced hydrophilicity by the tip treatments. The tip surface prepared by the Si coating is oxidized when it is immersed in aqueous solution. This creates local spots where stable hydration structures are formed. For the other methods, there is no active mechanism to create such local hydration sites. Thus, the hydration structure formed under the tip apex is not necessarily stable. These results reveal the desirable tip properties for atomic-scale AFM measurements in liquid, which should serve as a guideline for further improvements of the tip treatment methods. (paper)

  15. Computation of liquid-liquid equilibria and phase stabilities: implications for RH-dependent gas/particle partitioning of organic-inorganic aerosols

    Directory of Open Access Journals (Sweden)

    A. Zuend

    2010-08-01

    Full Text Available Semivolatile organic and inorganic aerosol species partition between the gas and aerosol particle phases to maintain thermodynamic equilibrium. Liquid-liquid phase separation into an organic-rich and an aqueous electrolyte phase can occur in the aerosol as a result of the salting-out effect. Such liquid-liquid equilibria (LLE affect the gas/particle partitioning of the different semivolatile compounds and might significantly alter both particle mass and composition as compared to a one-phase particle. We present a new liquid-liquid equilibrium and gas/particle partitioning model, using as a basis the group-contribution model AIOMFAC (Zuend et al., 2008. This model allows the reliable computation of the liquid-liquid coexistence curve (binodal, corresponding tie-lines, the limit of stability/metastability (spinodal, and further thermodynamic properties of multicomponent systems. Calculations for ternary and multicomponent alcohol/polyol-water-salt mixtures suggest that LLE are a prevalent feature of organic-inorganic aerosol systems. A six-component polyol-water-ammonium sulphate system is used to simulate effects of relative humidity (RH and the presence of liquid-liquid phase separation on the gas/particle partitioning. RH, salt concentration, and hydrophilicity (water-solubility are identified as key features in defining the region of a miscibility gap and govern the extent to which compound partitioning is affected by changes in RH. The model predicts that liquid-liquid phase separation can lead to either an increase or decrease in total particulate mass, depending on the overall composition of a system and the particle water content, which is related to the hydrophilicity of the different organic and inorganic compounds. Neglecting non-ideality and liquid-liquid phase separations by assuming an ideal mixture leads to an overestimation of the total particulate mass by up to 30% for the composition and RH range considered in the six

  16. STABILIZATION OF DRY SLUDGE OF LIQUID WASTE OF LEATHER TREATMENT BY USING FLY ASH

    Directory of Open Access Journals (Sweden)

    Cahya Widiyati

    2010-06-01

    Full Text Available The experiment of solidification of dry sludge of liquid waste of leather treatment are containing chrome (Cr by using fly ash has been done.  The experiment objective are immobilize Cr in the solid waste by using pozzoland cement was made of fly ash in order to stable in the repository.  The experiment were carried out by solidification of solid waste are containing total chrome of 1480.5 mg/kg sum of 2 - 10 weight % of (water + pozzoland cement by using pozzoland cement was made from the mixture of fly ash and calcite were burned at 1000 oC temperature for 2 hours.  The characterization of the solid composite of stabilization result consist of the compressive strength test and the leaching test by American Nuclear Society (ANS-16.1 method.  The experiment result were shown that pozzoland cement  can binding solid waste sum of 10 weight % of (water + pozzoland cement became the composite of waste concrete with the compressive strength of 577 ton/m2 and the chrome leaching test for 14 days of 0.059 mg/l.  The composite of waste concrete according to Bapedal rule for solidification of toxic waste with minimum compressive strength of 10 ton/m2 and maximum leached chrome of 5 mg/L.   Keywords: stabilization, solid waste, leather treatment, fly ash.

  17. Electrohydrostatic and electrohydrodynamic theories of equilibrium shapes and stability of electrically stressed conducting liquids

    International Nuclear Information System (INIS)

    Chung, M.S.

    1986-01-01

    This work represents an initial attempt at a systematic and rigorous study of the static and dynamic equilibrium shapes and stability of electrically stressed conducting fluids. The ultimate objective of the research is to explain the basic mechanism(s) describing the operation of a field emission liquid metal ion source. The variational procedure is used to obtain a set of equations whose solutions describe the static fluid shape as a function of applied field. Using an iterative procedure to solve Laplace's equation for an arbitrary geometry, a sequence of profiles is calculated that shows the evolution of the deformed fluid surface with applied field. A systematic study of stability is made by applying the Taylor and Zeleny criteria to quasi-statistically stressed fluids. To formulate a realistic and accurate description of the onset of instability, is is necessary to introduce fluid flow, which requires a dynamical analysis. To maintain contact with the LMIS configuration, the approach to instability is studied in axially symmetric fluids using a linearized set of electrohydrodynamic equations. The analysis is applied to different coordinate surfaces, which are used to model fluid shapes, which are observed, or assumed to exist, in an operating LMIS just prior to or at the onset of emission. Results suggest a new interpretation of the onset of instability

  18. Influence of pH, temperature and storage condition on survival and growth of Salmonella Enteritidis in membrane processed liquid egg white

    Science.gov (United States)

    Study was conducted to establish the effects of variations in liquid egg pH and membrane processing temperature on the removal and growth of Salmonella Enteritidis in liquid egg white (LEW) filtered by microfiltration (MF) process. Storage condition variations influence on growth of Salmonella in th...

  19. Determination of polybrominated diphenyl ethers at trace levels in environmental waters using hollow-fiber microporous membrane liquid-liquid extraction and gas chromatography-mass spectrometry.

    Science.gov (United States)

    Fontanals, Núria; Barri, Thaer; Bergström, Staffan; Jönsson, Jan-Ake

    2006-11-10

    In this study, we present a simple and easy-to-use extraction method that is based on a hollow-fiber microporous membrane liquid-liquid extraction (HF-MMLLE), as an extraction technique, followed by gas chromatography-mass spectrometry (GC-MS) to determine a group of brominated flame retardants (BFRs), polybrominated diphenyl ethers (PBDEs), at trace levels in aqueous samples. The hollow-fiber membrane (HF) filled with organic solvent was immersed into the aqueous sample, spiked with the analytes at ng l(-1) level, and stirred for 60 min. The proposed method could attain enrichment factors (E(e)) up to 5200 times, after optimising parameters, such as organic solvent, stirring speed and extraction time, that affect the extraction. The HF-MMLLE-GC-MS method was successfully applied to the extraction of PBDEs from tap, river and leachate water samples with spike recoveries ranging from 85% to 110%. The method validation with reagent and leachate water samples provided good linearity, detection limits of 1.1 ng l(-1) or lower, both in reagent and leachate water, as well as satisfactory precision in terms of repeatability and reproducibility with values of % relative standard deviation (%RSD) lower than 8.6 and 16.9, respectively.

  20. A hybrid liquid-phase precipitation (LPP) process in conjunction with membrane distillation (MD) for the treatment of the INEEL sodium-bearing liquid waste.

    Science.gov (United States)

    Bader, M S H

    2005-05-20

    A novel hybrid system combining liquid-phase precipitation (LPP) and membrane distillation (MD) is integrated for the treatment of the INEEL sodium-bearing liquid waste. The integrated system provides a "full separation" approach that consists of three main processing stages. The first stage is focused on the separation and recovery of nitric acid from the bulk of the waste stream using vacuum membrane distillation (VMD). In the second stage, polyvalent cations (mainly TRU elements and their fission products except cesium along with aluminum and other toxic metals) are separated from the bulk of monovalent anions and cations (dominantly sodium nitrate) by a front-end LPP. In the third stage, MD is used first to concentrate sodium nitrate to near saturation followed by a rear-end LPP to precipitate and separate sodium nitrate along with the remaining minor species from the bulk of the aqueous phase. The LPP-MD hybrid system uses a small amount of an additive and energy to carry out the treatment, addresses multiple critical species, extracts an economic value from some of waste species, generates minimal waste with suitable disposal paths, and offers rapid deployment. As such, the LPP-MD could be a valuable tool for multiple needs across the DOE complex where no effective or economic alternatives are available.

  1. Carrier-facilitated transport of Cd(II) through a supported liquid membrane containing thiacalix[4]arene derivatives as ionophore

    International Nuclear Information System (INIS)

    Zaghbani, Asma; Tayeb, Rafik; Dhahbi, Mahmoud

    2009-01-01

    The feasibility of a facilitated transport process of cadmium ions through a SLM system incorporating new extractant agents, thiacalix[4]arenes, was studied. These molecules have sulfur atoms instead of usual methylene bridges. The chemical modification of the upper or the lower rim provides a great variety of supra molecules having different complexation ability and different conformational behaviour. The efficiency of the transport across the inner membrane organic liquid phase is shown to depend on the chemical (affinity) and structural (conformational states possible) parameters of these complexing molecules. In this work, two different thiacalix[4]arenes were selected as effective ionophore for the treatment of liquid media loaded in Cd(II). The results show that these thiacalix[4]arenes derivative ensure facilitated transport of cadmium cations through supported liquid membranes. Especially, the non-substituted thiacalix[4]arene can be considered as an effective extractant agent. The incidence of several parameters on transport efficiency such as pH of both aqueous solutions and carrier concentration was studied. The permeation of the species is due to a proton potential gradient (the driving force of the process) existing between the two opposite sides of the SLM. The initial flux, J, is found to be equal to 6.7.10 -7 mol.m -2 .s -1 , under optimal experimental conditions.

  2. Separation of alkali, alkaline earth and rare earth cations by liquid membranes containing macrocyclic carriers. Third progress report, September 1, 1980-April 1, 1981

    International Nuclear Information System (INIS)

    Christensen, J.J.

    1981-01-01

    The overall objective of this project is to study the use of liquid membrane systems employing macrocyclic ligand carriers in making separations among metal cations. During the third year of the project, work continued in the development of a mathematical model to describe cation transport. The model was originally developed to describe the relationship between cation transport rate (J/sub M/) and the cation-macrocycle stability constant (K). The model was tested by determining the rates of transport of alkali and alkaline earth cations through chloroform membranes containing carrier ligands where the stability constants for their reaction with cations in methanol were known. From the results, it is clear that the model correctly describes the dependence of J/sub M/ on log K. The model also correctly describes the effect of cation concentration and carrier concentration on cation transport rates, as detailed in the previous progress report. During the third year of the project, the transport model was expanded so as to apply to competitive transport of cations from mixtures of two cations in the source aqueous phase. Data were collected under these conditions and the ability of the model to predict the flux of each cation was tested. Representative data of this type are presented along with corresponding data which were obtained when each cation was transported by the same carrier from a source phase containing only that cation. Comparison of transport rates determined under the two experimental conditions indicates that the relationship between the two sets of data is complex. To date, a few of these data involving transport from binary cation mixtures have been tested against the transport model. It was found that the model correctly predicts the cation fluxes from cation mixtures. These preliminary results indicate that the transport model can successfully predict separation factors when cation mixtures are used

  3. Effect of vertical quasiperiodic vibrations on the stability of the free surface of an inviscid liquid layer

    Directory of Open Access Journals (Sweden)

    Belhaq M.

    2012-07-01

    Full Text Available The aim of the present paper is to examine the effect of the vertical quasiperiodic oscillations on the stability of the free surface of an ideal horizontal liquid layer. The quasiperiodic motion considered here is characterized by two incommensurate frequencies ω1 and ω2. The governing system of equations is reduced to a quasiperiodic Mathieu equation. In this situation, using the harmonic balance method developed by Rand et al. [10, 11] and Hill’s determinants, we determine the marginal stability curves. We show that the quasiperiodic excitation produces a stabilizing or a estabilizing effect and is strongly depending on the ratio of the frequencies.

  4. Hydrogen production by reforming of liquid hydrocarbons in a membrane reactor for portable power generation-Experimental studies

    Science.gov (United States)

    Damle, Ashok S.

    One of the most promising technologies for lightweight, compact, portable power generation is proton exchange membrane (PEM) fuel cells. PEM fuel cells, however, require a source of pure hydrogen. Steam reforming of hydrocarbons in an integrated membrane reactor has potential to provide pure hydrogen in a compact system. Continuous separation of product hydrogen from the reforming gas mixture is expected to increase the yield of hydrogen significantly as predicted by model simulations. In the laboratory-scale experimental studies reported here steam reforming of liquid hydrocarbon fuels, butane, methanol and Clearlite ® was conducted to produce pure hydrogen in a single step membrane reformer using commercially available Pd-Ag foil membranes and reforming/WGS catalysts. All of the experimental results demonstrated increase in hydrocarbon conversion due to hydrogen separation when compared with the hydrocarbon conversion without any hydrogen separation. Increase in hydrogen recovery was also shown to result in corresponding increase in hydrocarbon conversion in these studies demonstrating the basic concept. The experiments also provided insight into the effect of individual variables such as pressure, temperature, gas space velocity, and steam to carbon ratio. Steam reforming of butane was found to be limited by reaction kinetics for the experimental conditions used: catalysts used, average gas space velocity, and the reactor characteristics of surface area to volume ratio. Steam reforming of methanol in the presence of only WGS catalyst on the other hand indicated that the membrane reactor performance was limited by membrane permeation, especially at lower temperatures and lower feed pressures due to slower reconstitution of CO and H 2 into methane thus maintaining high hydrogen partial pressures in the reacting gas mixture. The limited amount of data collected with steam reforming of Clearlite ® indicated very good match between theoretical predictions and

  5. Radiation stability of diglycolamide functionalized calix[4]arenes in ionic liquid: Solvent extraction, EPR and GC–MS studies

    NARCIS (Netherlands)

    Sengupta, A; Mohapatra, P.K.; Patil, A.B.; Kadam, R.M.; Verboom, Willem

    2016-01-01

    Ionic liquid-based solvent systems containing diglycolamide-functionalized calix[4]arenes (C4DGAs) are efficient for actinide ion extraction from nitric acid feeds. Therefore, the radiolytic stability of three C4DGAs (wide-rim, narrow-rim and both side DGA-functionalized calix[4]arenes) and TODGA

  6. Synthesis, Characterization, and Impregnation of Some Ionic Liquids on Polymer Membrane for Separation of Carbon Dioxide from Its Mixture with Methane

    Directory of Open Access Journals (Sweden)

    T. T. L. Bui

    2018-03-01

    Full Text Available Some 1-alkyl-3-methylimidazolium-based ionic liquids were synthesized, characterized, and immobilized on membranes to form supported ionic liquid membranes. The supported ionic liquid membranes were characterized by SEM. The initial transmembrane pressures were investigated for each type of impregnated membrane. The CO2/CH4 single gas and mixed gas permeability (CO2 and CH4 have been investigated. The results showed that the CO2/CH4 ideal selectivities and mixed gas selectivities reached 15.45 – 23.9 and 13.91 – 22.82, respectively (equivalent to separation yields of 93.3 – 95.98 %.mThe 1-alkyl-3-methylimidazolium acetate impregnated membrane leads to a slightly lowermCO2/CH4 selectivity, however, this ionic liquid is stable, free of halogen and has a low price. The impregnated membranes prepared from polyvinylidene fluoride are more stablemthan those from polyethersulfone support, and have a higher affinity for CO2 compared to other gas. The obtained high CO2/CH4 selectivities indicate that immobilized membranes can be used for CO2 separation processes.

  7. Reforming of Liquid Hydrocarbons in a Novel Hydrogen-Selective Membrane-Based Fuel Processor

    Energy Technology Data Exchange (ETDEWEB)

    Shamsuddin Ilias

    2006-03-10

    In this work, asymmetric dense Pd/porous stainless steel composite membranes were fabricated by depositing palladium on the outer surface of the tubular support. The electroless plating method combined with an osmotic pressure field was used to deposit the palladium film. Surface morphology and microstructure of the composite membranes were characterized by SEM and EDX. The SEM and EDX analyses revealed strong adhesion of the plated pure palladium film on the substrate and dense coalescence of the Pd film. Membranes were further characterized by conducting permeability experiments with pure hydrogen, nitrogen, and helium gases at temperatures from 325 to 450 C and transmembrane pressure differences from 5 to 45 psi. The permeation results showed that the fabricated membranes have both high hydrogen permeability and selectivity. For example, the hydrogen permeability for a composite membrane with a 20 {micro}m Pd film was 3.02 x 10{sup -5} moles/m{sup 2}.s.Pa{sup 0.765} at 450 C. Hydrogen/nitrogen selectivity for this composite membrane was 1000 at 450 C with a transmembrane pressure difference of 14.7 psi. Steam reforming of methane is one of the most important chemical processes in hydrogen and syngas production. To investigate the usefulness of palladium-based composite membranes in membrane-reactor configuration for simultaneous production and separation of hydrogen, steam reforming of methane by equilibrium shift was studied. The steam reforming of methane using a packed-bed inert membrane tubular reactor (PBIMTR) was simulated. A two-dimensional pseudo-homogeneous reactor model with parallel flow configuration was developed for steam reforming of methane. The shell volume was taken as the feed and sweep gas was fed to the inside of the membrane tube. Radial diffusion was taken into account for concentration gradient in the radial direction due to hydrogen permeation through the membrane. With appropriate reaction rate expressions, a set of partial differential

  8. A study of chemical modifications of a Nafion membrane by incorporation of different room temperature ionic liquids

    Energy Technology Data Exchange (ETDEWEB)

    Martinez de Yuso, M.V.; Rodriguez-Castellon, E. [Departamento de Quimica Inorganica, Facultad de Ciencias, Universidad de Malaga (Spain); Neves, L.A.; Coelhoso, I.M.; Crespo, J.G. [REQUIMTE/CQFB, Departamento de Quimica, Universidade Nova de Lisboa, Caparica (Portugal); Benavente, J. [Departamento de Fisica Aplicada I, Facultad de Ciencias, Universidad de Malaga (Spain)

    2012-08-15

    Surface and bulk chemical changes in a Nafion membrane as a result of room temperature ionic liquids (RTILs) incorporation were determined by X-ray photoelectron spectroscopy (XPS) and elemental analysis, respectively. RTILs with different physicochemical properties were selected. Two imidazolium based RTIL-cations (1-octyl-3-methylimidazolium and 1-butyl-3-methylimidazolium) were used to detect the effect of cation size on membrane modification, while the effect of the RTIL hydrophilic/hydrophobic character was also considered by choosing different anions. Angle resolved XPS measurements (ARXPS) were carried out varying the angle of analysis between 15 and 75 to get elemental information on the Nafion/RTIL-modified membranes interactions for a deepness of around 10 nm. Moreover, changes in the RTIL-modified membranes associated to thermal effect were also considered by analyzing the samples after their heating at 120 C for 24 h. Agreement between both chemical techniques, bulk and destructive elemental analysis and surface and non-destructive XPS, were obtained. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  9. Toward the Fabrication of Advanced Nanofiltration Membranes by Controlling Morphologies and Mesochannel Orientations of Hexagonal Lyotropic Liquid Crystals.

    Science.gov (United States)

    Wang, Guang; Garvey, Christopher J; Zhao, Han; Huang, Kang; Kong, Lingxue

    2017-07-21

    Water scarcity has been recognized as one of the major threats to human activity, and, therefore, water purification technologies are increasingly drawing attention worldwide. Nanofiltration (NF) membrane technology has been proven to be an efficient and cost-effective way in terms of the size and continuity of the nanostructure. Using a template based on hexagonal lyotropic liquid crystals (LLCs) and partitioning monomer units within this structure for subsequent photo-polymerisation presents a unique path for the fabrication of NF membranes, potentially producing pores of uniform size, ranging from 1 to 5 nm, and large surface areas. The subsequent orientation of this pore network in a direction normal to a flat polymer film that provides ideal transport properties associated with continuous pores running through the membrane has been achieved by the orientation of hexagonal LLCs through various strategies. This review presents the current progresses on the strategies for structure retention from a hexagonal LLCs template and the up-to-date techniques used for the reorientation of mesochanels for continuity through the whole membrane.

  10. Toward the Fabrication of Advanced Nanofiltration Membranes by Controlling Morphologies and Mesochannel Orientations of Hexagonal Lyotropic Liquid Crystals

    Directory of Open Access Journals (Sweden)

    Guang Wang

    2017-07-01

    Full Text Available Water scarcity has been recognized as one of the major threats to human activity, and, therefore, water purification technologies are increasingly drawing attention worldwide. Nanofiltration (NF membrane technology has been proven to be an efficient and cost-effective way in terms of the size and continuity of the nanostructure. Using a template based on hexagonal lyotropic liquid crystals (LLCs and partitioning monomer units within this structure for subsequent photo-polymerisation presents a unique path for the fabrication of NF membranes, potentially producing pores of uniform size, ranging from 1 to 5 nm, and large surface areas. The subsequent orientation of this pore network in a direction normal to a flat polymer film that provides ideal transport properties associated with continuous pores running through the membrane has been achieved by the orientation of hexagonal LLCs through various strategies. This review presents the current progresses on the strategies for structure retention from a hexagonal LLCs template and the up-to-date techniques used for the reorientation of mesochanels for continuity through the whole membrane.

  11. Aquifex aeolicus membrane hydrogenase for hydrogen biooxidation: Role of lipids and physiological partners in enzyme stability and activity

    Energy Technology Data Exchange (ETDEWEB)

    Infossi, Pascale; Lojou, Elisabeth; Giudici-Orticoni, Marie-Therese [Unite de Bioenergetique et Ingenierie des Proteines, UPR 9036, Institut de Microbiologie de la Mediterranee - CNRS, 31 Chemin Joseph Aiguier, 13402 Marseille Cedex 20 (France); Chauvin, Jean-Paul [Institut de Biologie du developpement de Marseille Luminy, UMR 6216, Parc Scientifique de Luminy, 163 Avenue de Luminy, BP 907, 13009 Marseille (France); Herbette, Gaetan [Spectropole FI 1739, Aix-Marseille Universite case 511, Faculte de St Jerome Avenue Escadrille Normandie Niemen, 13397 Marseille Cedex 20 (France); Brugna, Myriam [Unite de Bioenergetique et Ingenierie des Proteines, UPR 9036, Institut de Microbiologie de la Mediterranee - CNRS, 31 Chemin Joseph Aiguier, 13402 Marseille Cedex 20 (France); Universite de Provence, 3 Place Victor Hugo, 13331 Marseille Cedex 03 (France)

    2010-10-15

    Hydrogenase I from the hyperthermophilic bacterium Aquifex aeolicus is a good candidate for biotechnological devices thanks to its ability to oxidize hydrogen at high temperature, even in the presence of oxygen and CO. In order to enhance the enzyme stability and the catalytic efficiency, we investigated the hydrogen oxidation process with hydrogenase I embedded in a physiological-like environment. Hydrogenase I partners in the metabolic chain, namely membrane quinone and cytochrome b, were purified and fully characterized. The complex hydrogenase I-cytochrome b was inserted into liposomes. Surface Plasmon Resonance revealed that quinone took part in the stabilization of the complex. By use of molecular modelization and electrochemistry analysis, enzyme stability has been demonstrated to be stronger and enzymatic efficiency to be five times higher when hydrogenase is embedded into the liposomes. This result raises the possibility of using hydrogenases as biocatalysts in fuel cells. (author)

  12. High-performance liquid chromatography separation and intact mass analysis of detergent-solubilized integral membrane proteins

    Science.gov (United States)

    Berridge, Georgina; Chalk, Rod; D’Avanzo, Nazzareno; Dong, Liang; Doyle, Declan; Kim, Jung-In; Xia, Xiaobing; Burgess-Brown, Nicola; deRiso, Antonio; Carpenter, Elisabeth Paula; Gileadi, Opher

    2011-01-01

    We have developed a method for intact mass analysis of detergent-solubilized and purified integral membrane proteins using liquid chromatography–mass spectrometry (LC–MS) with methanol as the organic mobile phase. Membrane proteins and detergents are separated chromatographically during the isocratic stage of the gradient profile from a 150-mm C3 reversed-phase column. The mass accuracy is comparable to standard methods employed for soluble proteins; the sensitivity is 10-fold lower, requiring 0.2–5 μg of protein. The method is also compatible with our standard LC–MS method used for intact mass analysis of soluble proteins and may therefore be applied on a multiuser instrument or in a high-throughput environment. PMID:21093405

  13. Stuides on a Pb2+-selective electrode with a macrocyclic liquid membrane. Potentiometric determination of Pb2+ ions

    Directory of Open Access Journals (Sweden)

    MARIAN ISVORANU

    2006-12-01

    Full Text Available This paper presents experimental and theoretical data regarding the design, characterization and analytical applications of a non-expensive, liquid-membrane ion-selective electrode for Pb2+ ions. The membrane is a solution of the active complex formed by Pb2+ ions with dibenzo-18-crown-6-ionophore (DB-[18]-C-6 extracted in propylene carbonate (PC. The sucessful application of the developed electrode for the determination of Pb2+ ions in aqueos solution samples by direct potentiometry and potentiometric titration is presented. For the presented analytical results, there are insignificant systematic errors between the direct potentiometric method with the developed ion-selective electrode and atomic absorption spectrometry.

  14. Stability and structure of the membrane protein transporter Ffh is modulated by substrates and lipids

    DEFF Research Database (Denmark)

    Reinau, Marika Ejby; Otzen, Daniel

    2009-01-01

    the apoprotein. Escherichia coli lipid and DOPG (and to a smaller extent DOPC) increase Ffh's α-helical content, possibly related to Ffh's role in guiding membrane proteins to the membrane. Binding is largely mediated by electrostatic interactions but does not protect Ffh against trypsinolysis. We conclude...

  15. A Stability Study of Alkali Doped PBI Membranes for Alkaline Electrolyzer Cells

    DEFF Research Database (Denmark)

    Jensen, Jens Oluf; Aili, David; Hansen, Martin Kalmar

    2014-01-01

    Polybenzimidazole membranes in a linear, a crosslinked and a thermally cured form were subjected to aging in 6 M aqueous KOH at 85 ºC for periods of up to 176 days. The aged membranes were characterized with respect to weight loss, mechanical properties and ionic conductivity. The area specific c...

  16. Assembly of Lyotropic Liquid Crystals with Solid Crystal's Structural Order Translated from the Lipid Rafts in Cell Membranes.

    Science.gov (United States)

    Lee, Yoon Seob

    2017-11-29

    Self-assembly offers a powerful way to control the complexity and hierarchy of nanoscale materials, and promises to create a diverse range of emergent properties. Successful syntheses that allow a delicate structural design of building units play an important role. However, as can be learned from many cellular processes and functions, coself-assembly using logically chosen additives should be equally effective in designing self-assembly. Herein I show that, translated from the dynamic nanoscale assemblies in cell membranes known as lipid rafts, coself-assembly of 1-decanol into cetyltrimethylammonium chloride micelles for the assembly of lyotropic liquid crystals generates new structural complexity and hierarchy, and a surprising property that is emerging from it. Designing the intermolecular forces in the way that cholesterol interacts with sphingolipids promotes the synergistic balance between the flexibility and rigidity, and the unique molecular recognition for silicic acid, followed by the micelle coalescence. This very much resembles the assembly process of the lipid rafts in cell membranes and triggers orders of magnitude of sharp increases in X-ray diffraction intensity. The analysis of the diffraction patterns shows that the structural order of these liquid crystals matches that of solid crystals, often of single crystals. Furthermore, the assembly of the liquid crystals promotes a substantial increase in the condensation rate of silicic acids by guiding them to form a silicate trimer along the surface of micelles. This very much resembles the role of the lipid rafts that sharply increases the reaction rate of biomolecules by guiding them to form discrete species along the surface of membranes. This finding demonstrates that it is possible to translate the key features of cellular processes and functions into artificial self-assembling systems of our choice using the building units that are readily available, thus creating novel soft materials.

  17. Facilitated transport of uranium(VI) across supported liquid membranes containing T2EHDGA as the carrier extractant.

    Science.gov (United States)

    Panja, S; Mohapatra, P K; Tripathi, S C; Manchanda, V K

    2011-04-15

    Facilitated transport of uranyl ion from nitric acid feed solutions was investigated across PTFE supported liquid membranes using N,N,N',N'-tetra-2-ethylhexyl-3-pentane-diamide (T2EHDGA) in n-dodecane as the carrier extractant containing 30% iso-decanol as the phase modifier. Solvent extraction studies indicated extraction of species of the type, UO(2)(NO(3))(2)·T2EHDGA. The distribution coefficients increased in the presence of NaNO(3) as compared to equivalent concentration of HNO(3) which was exactly the opposite of what was reported for Am(III)-TODGA extraction system. Supported liquid membrane studies indicated about 11h were required for quantitative transport of U(VI) from a feed of 3M HNO(3) using 0.2M T2EHDGA in n-dodecane containing 30% iso-decanol as the carrier extractant. Effect of various parameters such as feed acidity, T2EHDGA concentration, and nature of the strippant on the transport rate was investigated. The transport was found to be diffusion controlled in the membrane phase and the permeability coefficient was calculated to be (3.20 ± 0.13)× 10(-4)cm/s for the feed composition of 3M HNO(3), receiver phase composition of 0.01 M HNO(3) and membrane carrier phase of 0.2M T2EHDGA in n-dodecane containing 30% iso-decanol. The present results may be useful for the separation of U from lean solutions or radioactive wastes considered hazardous due to the presence of alpha-particle emitting radionuclides. Copyright © 2011 Elsevier B.V. All rights reserved.

  18. Simulation studies of ammonia removal from water in a membrane contactor under liquid-liquid extraction mode.

    Science.gov (United States)

    Mandowara, Amish; Bhattacharya, Prashant K

    2011-01-01

    Simulation studies were carried out, in an unsteady state, for the removal of ammonia from water via a membrane contactor. The contactor had an aqueous solution of NH(3) in the lumen and sulphuric acid in the shell side. The model equations were developed considering radial and axial diffusion and convection in the lumen. The partial differential equations were converted by the finite difference technique into a series of stiff ordinary differential equations w.r.t. time and solved using MATLAB. Excellent agreement was observed between the simulation results and experimental data (from the literature) for a contactor of 75 fibres. Excellent agreement was also observed between the simulation results and laboratory-generated data from a contactor containing 10,200 fibres. Our model is more suitable than the plug-flow model for designing the operation of the membrane contactor. The plug-flow model over-predicts the fractional removal of ammonia and was observed to be limited when designing longer contactors. Copyright © 2010 Elsevier Ltd. All rights reserved.

  19. Photoregenerative I−/I3− couple as a liquid cathode for proton exchange membrane fuel cell

    Science.gov (United States)

    Liu, Zhen; Wang, Yadong; Ai, Xinping; Tu, Wenmao; Pan, Mu

    2014-01-01

    A photoassisted oxygen reduction reaction (ORR) through I−/I3− redox couple was investigated for proton exchange membrane (PEM) fuel cell cathode reaction. The I−/I3−-based liquid cathode was used to replace conventional oxygen cathode, and its discharge product I− was regenerated to I3− by photocatalytic oxidation with the participation of oxygen. This new and innovative approach may provide a strategy to eliminate the usage of challenging ORR electrocatalysts, resulting in an avenue for developing low-cost and high-efficiency PEM fuel cells. PMID:25348812

  20. Gas transport properties and pervaporation performance of fluoropolymer gel membranes based on pure and mixed ionic liquids

    Czech Academy of Sciences Publication Activity Database

    Jansen, J. C.; Clarizia, G.; Bernardo, P.; Bazzarelli, F.; Friess, K.; Randová, A.; Schauer, Jan; Kubicka, D.; Kačírková, Marie; Izák, Pavel

    2013-01-01

    Roč. 109, 9 May (2013), s. 87-97 ISSN 1383-5866 R&D Projects: GA ČR GA104/08/0600; GA ČR GAP106/10/1194; GA MŠk(CZ) 7C11009 Grant - others:RFCS(XE) RFCR–CT–2010–00009 Institutional research plan: CEZ:AV0Z40720504 Institutional support: RVO:61389013 ; RVO:67985858 Keywords : ionic liquid membrane * gas permeability * pervaporation Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 3.065, year: 2013