Seasonal variability and descent of mid-latitude sporadic E layers at Arecibo

Directory of Open Access Journals (Sweden)

N. Christakis

2009-03-01

Full Text Available Sporadic E layers (Es follow regular daily patterns in variability and altitude descent, which are determined primarily by the vertical tidal wind shears in the lower thermosphere. In the present study a large set of sporadic E layer incoherent scatter radar (ISR measurements are analyzed. These were made at Arecibo (Geog. Lat. ~18° N; Magnetic Dip ~50° over many years with ISR runs lasting from several hours to several days, covering evenly all seasons. A new methodology is applied, in which both weak and strong layers are clearly traced by using the vertical electron density gradient as a function of altitude and time. Taking a time base equal to the 24-h local day, statistics were obtained on the seasonal behavior of the diurnal and semidiurnal tidal variability and altitude descent patterns of sporadic E at Arecibo. The diurnal tide, most likely the S(1,1 tide with a vertical wavelength around 25 km, controls fully the formation and descent of the metallic Es layers at low altitudes below 110 km. At higher altitudes, there are two prevailing layers formed presumably by vertical wind shears associated mainly with semidiurnal tides. These include: 1 a daytime layer starting at ~130 km around midday and descending down to 105 km by local midnight, and 2 a less frequent and weaker nighttime layer which starts prior to midnight at ~130 km, descending downwards at somewhat faster rate to reach 110 km by sunrise. The diurnal and semidiurnal-like pattern prevails, with some differences, in all seasons. The differences in occurrence, strength and descending speeds between the daytime and nighttime upper layers are not well understood from the present data alone and require further study.

Seizures in E200K familial and sporadic Creutzfeldt-Jakob disease.

Science.gov (United States)

Appel, S; Chapman, J; Cohen, O S; Rosenmann, H; Nitsan, Z; Blatt, I

2015-03-01

Although seizures (other than myoclonus) are frequently reported in Creutzfeldt-Jakob disease (CJD), their frequency, clinical manifestations, and effect on the disease course is unknown. To characterize the frequency of seizures in E200K familial and sporadic CJD, to describe its semiology, EEG and MRI findings. In this retrospective study, we reviewed all patients with CJD who were seen in the Sheba Medical Center between the years 2003-2012 and underwent clinical evaluation, genetic testing, EEG and MRI studies. The diagnosis of seizures was carried out based on documentation of episodes consistent with seizures or episode of unresponsiveness correlated with ictal activity in EEG. Sixty-four probable patients with CJD were included in the study, 57 (89%) with E200K familial (fCJD) and 7 (11%) with sporadic (sCJD). Seizures occurred in 8 patients: 3 of 7 (43%) in patients with sCJD compared to 5/57 (9%) in patients with E200K fCJD (P = 0.04, chi-square test). Two of E200K fCJD patients with seizures had other non-prion etiologies for seizures (brain metastasis, known history of temporal lobe epilepsy which started 44 years before the diagnosis of CJD). Seizures occurred late in the course of the disease with an average of 12 days between the onset of seizures and death. Seizures in E200K fCJD were infrequent and occurred late in the disease course. This difference suggests that E200K fCJD represents a separate subtype of the disease with distinct clinical characteristics. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Studies of sporadic E (Es) associated with the main ionospheric trough

International Nuclear Information System (INIS)

Rodger, A.S.; Morrell, C.; Dudeney, J.R.

1983-01-01

Sporadic E, or E(s) events under the main F region trough have been confirmed on the basis of ionograms from a vertical incidence ionosonde at Halley Bay, Antarctica. Analyses indicate that E(s) is frequently observable under both the equatorward and the poleward edges of the trough, as well as poleward of it. Before magnetic midnight, E(s) layers whose semithickness resembles those of the normal E layer are common, in contrast to layers seen after magnetic midnight which show the characteristics of thin E(s) layers. A possible explanation of the observed change in the E(s) layer characteristics at magnetic midnight is related to differences in the type and spectra of the precipitating particles. It is shown that the redistribution of ionization by the convection electric field may be important. 40 references

Height and critical frequency variations of the sporadic-E layer at midlatitudes

Czech Academy of Sciences Publication Activity Database

Šauli, Petra; Bourdillon, A.

2008-01-01

Roč. 70, č. 15 (2008), s. 1904-1910 ISSN 1364-6826 R&D Projects: GA AV ČR IAA300420704 Grant - others:European Union(XE) COST 296 Institutional research plan: CEZ:AV0Z30420517 Keywords : Sporadic E * Planetary waves * Tidal waves * Mid-latitude ionosphere * Wavelet transform Subject RIV: DG - Athmosphere Sciences, Meteorology Impact factor: 1.667, year: 2008

Association of apolipoprotein E allele {epsilon}4 with late-onset sporadic Alzheimer`s disease

Energy Technology Data Exchange (ETDEWEB)

Lucotte, G.; David, F.; Berriche, S. [Regional Center of Neurogenetics, Reims (France)] [and others

1994-09-15

Apolipoprotein E, type {epsilon}4 allele (ApoE {epsilon}4), is associated with late-onset sporadic Alzheimer`s disease (AD) in French patients. The association is highly significant (0.45 AD versus 0.12 controls for {epsilon}4 allele frequencies). These data support the involvement of ApoE {epsilon}4 allele as a very important risk factor for the clinical expression of AD. 22 refs., 1 fig., 3 tabs.

CRRES observations of stormtime ring current ion composition

International Nuclear Information System (INIS)

Roeder, J.L.; Fennell, J.F.; Chen, M.W.; Grande, M.; Livi, S.; Schulz, M.

1996-01-01

The Magnetospheric Ion Composition Spectrometer onboard the CRRES spacecraft provided mass and charge state composition data for positive ions in the energy-per-charge range 1 endash 426 keV/e. The CRRES data is compared to the AMPTE/CCE observations during a moderately large geomagnetic storm on 4 June 1991. The results are compared to observations of large storms by CRRES and by the AMPTE/CCE spacecraft. The CRRES data show that oxygen ions formed 29% of the total measured ion energy density at L=3 endash 5 during the storm recovery phase. This result implies that domination of the plasma by oxygen ions may not be necessary to produce the observed rapid initial recovery of the Dst magnetic index. A preliminary test of the Dessler-Parker-Sckopke relation between the ion energy and the global magnetic perturbation shows that the observed particle fluxes during the 4 June 1991 storm could account for only 40 endash 70% of the variation of Dst. copyright 1996 American Institute of Physics

Searching for effects caused by thunderstorms in midlatitude sporadic E layers

Czech Academy of Sciences Publication Activity Database

Barta, V.; Haldoupis, C.; Sátori, G.; Burešová, Dalia; Chum, Jaroslav; Pozoga, M.; Berényi, K. A.; Bór, J.; Popek, Martin; Kis, Á.; Bencze, P.

2017-01-01

Roč. 161, August (2017), s. 150-159 ISSN 1364-6826 R&D Projects: GA ČR(CZ) GC15-07281J; GA ČR(CZ) GAP209/12/2440; GA ČR(CZ) GA14-31899S Institutional support: RVO:68378289 Keywords : atmospheric gravity waves * ionosphere coupling * lightning * sporadic E layer * sprites * thunderstorm Subject RIV: DG - Athmosphere Sciences, Meteorology OBOR OECD: Meteorology and atmospheric sciences Impact factor: 1.326, year: 2016 https://arxiv.org/abs/1708.00270

Electric field measurements of DC and long wavelength structures associated with sporadic-E layers and QP radar echoes

Directory of Open Access Journals (Sweden)

S. Ohtsuki

2005-10-01

Full Text Available Electric field and plasma density data gathered on a sounding rocket launched from Uchinoura Space Center, Japan, reveal a complex electrodynamics associated with sporadic-E layers and simultaneous observations of quasi-periodic radar echoes. The electrodynamics are characterized by spatial and temporal variations that differed considerably between the rocket's upleg and downleg traversals of the lower ionosphere. Within the main sporadic-E layer (95–110 km on the upleg, the electric fields were variable, with amplitudes of 2–4 mV/m that changed considerably within altitude intervals of 1–3 km. The identification of polarization electric fields coinciding with plasma density enhancements and/or depletions is not readily apparent. Within this region on the downleg, however, the direction of the electric field revealed a marked change that coincided precisely with the peak of a single, narrow sporadic-E plasma density layer near 102.5 km. This shear was presumably associated with the neutral wind shear responsible for the layer formation. The electric field data above the sporadic-E layer on the upleg, from 110 km to the rocket apogee of 152 km, revealed a continuous train of distinct, large scale, quasi-periodic structures with wavelengths of 10–15 km and wavevectors oriented between the NE-SW quadrants. The electric field structures had typical amplitudes of 3–5 mV/m with one excursion to 9 mV/m, and in a very general sense, were associated with perturbations in the plasma density. The electric field waveforms showed evidence for steepening and/or convergence effects and presumably had mapped upwards along the magnetic field from the sporadic-E region below. Candidate mechanisms to explain the origin of these structures include the Kelvin-Helmholtz instability and the Es-layer instability. In both cases, the same shear that formed the sporadic-E layer would provide the energy to generate the km-scale structures. Other possibilities

The study on the ion exchange behavior of metal ions using composite ion exchange resin

Energy Technology Data Exchange (ETDEWEB)

Kim, Kukki; Lee, Kunjai [Nuclear Engineering Department Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of); Kim, Youngkyun [Korea Institute of Nuclear Safety, Daejon (Korea, Republic of); Lee, Sangjin; Yang, Hoyeon; Ha, Jonghyun [Korea Hydro and Nuclear Power Co., Daejeon (Korea, Republic of)

2002-04-15

In this study, a series of stepwise procedures to prepare a new organic-inorganic composite magnetic resin with phenol sulphonic-formaldehyde and freshly formed iron ferrite was established, based upon wet-and-neutralization method for synthesizing iron ferrite and pearl-polymerization method for synthesizing rigid bead-type composite resin. And a separation of metal ions in the liquid radioactive waste have been performed using organic-inorganic composite magnetic resin with phenol sulphonic-formaldehyde and freshly formed iron ferrite. The PSF-F (phenol sulphonic formaldehyde-iron ferrite) composite resin prepared by the above method shows stably high removal efficiency to Co(II), Fe, Cs species from wastewater in a wide range of solution pH. The wide range of applicable solution pH (i. e. pH 4.0 to 10.3) implies that the PSF-F composite resin overcomes the limitations of the conventional ferrite process which is practically applicable only to alkaline conditions. The experiment proceeded using batch reactor in a constant temperature with water bath. The experiments divided into three parts. The first one is TG/DTA (Thermogravimetry / Differential Thermal Analysis) which can analyze the trend of pyrolysis of PSF-F ion exchanger. The Second one is equilibrium experiment in which the separation factor of metal ions and Langmuir, Freundlich isotherm was achieved. The last one is kinetics experiment in which the equilibrium reaction time and removal efficiency is estimated.

The study on the ion exchange behavior of metal ions using composite ion exchange resin

International Nuclear Information System (INIS)

Kim, Kukki; Lee, Kunjai; Kim, Youngkyun; Lee, Sangjin; Yang, Hoyeon; Ha, Jonghyun

2002-01-01

In this study, a series of stepwise procedures to prepare a new organic-inorganic composite magnetic resin with phenol sulphonic-formaldehyde and freshly formed iron ferrite was established, based upon wet-and-neutralization method for synthesizing iron ferrite and pearl-polymerization method for synthesizing rigid bead-type composite resin. And a separation of metal ions in the liquid radioactive waste have been performed using organic-inorganic composite magnetic resin with phenol sulphonic-formaldehyde and freshly formed iron ferrite. The PSF-F (phenol sulphonic formaldehyde-iron ferrite) composite resin prepared by the above method shows stably high removal efficiency to Co(II), Fe, Cs species from wastewater in a wide range of solution pH. The wide range of applicable solution pH (i. e. pH 4.0 to 10.3) implies that the PSF-F composite resin overcomes the limitations of the conventional ferrite process which is practically applicable only to alkaline conditions. The experiment proceeded using batch reactor in a constant temperature with water bath. The experiments divided into three parts. The first one is TG/DTA (Thermogravimetry / Differential Thermal Analysis) which can analyze the trend of pyrolysis of PSF-F ion exchanger. The Second one is equilibrium experiment in which the separation factor of metal ions and Langmuir, Freundlich isotherm was achieved. The last one is kinetics experiment in which the equilibrium reaction time and removal efficiency is estimated

SEEK-2 (Sporadic-E Experiment over Kyushu 2 − Project Outline, and Significance

Directory of Open Access Journals (Sweden)

R. Pfaff

2005-10-01

Full Text Available SEEK-2 (Sporadic-E Experiment over Kyushu 2 is an observation campaign to study the spatial structure of the field-aligned irregularity (FAI and sporadic-E(Es-layer by means of two sounding rockets and a ground-based observation network with radars and optical instruments. The experiment was successfully conducted on 3 August 2002, with successive launches of two sounding rockets from the Uchinoura Space Center (USC of the Japan Aerospace Exploration Agency (JAXA. The timing of the experiment was carefully selected, while intense quasi-periodic (QP echoes were observed with two radars in Tanegashima. The main Es-layer, with its double-layered structure, was observed at altitudes of 103–105 km, the presence of which was well accounted for by the ion accumulation due to neutral-wind shear. Several minor peaks were detected in the electron density profiles at altitudes of up to 130 km. The intensity of the electric field was 5–10 mV/m and showed intense fluctuations below 110 km. Wave-like variation of the electric field was seen above 110 km. From radar experiments, we found that QP echoes appeared around 105 km, which agreed well with the main Es-layer height. The QP echoes propagated to the west-northwest, with frontal structures elongated from north-northeast to south-southwest. Radar observations conduced throughout the SEEK-2 period, on the other hand, showed that frontal structures of the QP echoes were most frequently propagated to the southeast. This result was consistent with the direction of gravity-wave propagation observed with the OH imager during the same period. The rocket beacon experiment with the Es-layers revealed the spatial structure of the plasma densities. On the basis of these results and those from SEEK-1 in 1996, we examined the structures of the nighttime mid-latitude E-region. We concluded that the QP echoes reflect the horizontal structures of the main Es-layers. The source of the structures was not clearly

Energetics and structure of the lower E region associated with sporadic E layer

Directory of Open Access Journals (Sweden)

K.-I. Oyama

2008-09-01

Full Text Available The electron temperature (T_e, electron density (N_e, and two components of the electric field were measured from the height of 90 km to 150 km by one of the sounding rockets launched during the SEEK-2 campaign. The rocket went through sporadic E layer (E_s at the height of 102 km–109 km during ascent and 99 km–108 km during decent, respectively. The energy density of thermal electrons calculated from N_e and T_e shows the broad maximum in the height range of 100–110 km, and it decreases towards the lower and higher altitudes, which implies that a heat source exists in the height region of 100 km–110 km. A 3-D picture of E_s, that was drawn by using T_e, N_e, and the electric field data, corresponded to the computer simulation; the main structure of E_s is projected to a higher altitude along the magnetic line of force, thus producing irregular structures of T_e, N_e and electric field in higher altitude.

Common volume coherent and incoherent scatter radar observations of mid-latitude sporadic E-layers and QP echoes

Directory of Open Access Journals (Sweden)

D. L. Hysell

2004-09-01

Full Text Available Common-volume observations of sporadic E-layers made on 14-15 June 2002 with the Arecibo incoherent scatter radar and a 30MHz coherent scatter radar imager located on St. Croix are described. Operating in dual-beam mode, the Arecibo radar detected a slowly descending sporadic E-layer accompanied by a series of dense E-region plasma clouds at a time when the coherent scatter radar was detecting quasi-periodic (QP echoes. Using coherent radar imaging, we collocate the sources of the coherent scatter with the plasma clouds observed by Arecibo. In addition to patchy, polarized scattering regions drifting through the radar illuminated volume, which have been observed in previous imaging experiments, the 30MHz radar also detected large-scale electrostatic waves in the E-region over Puerto Rico, with a wavelength of about 30km and a period of about 10min, propagating to the southwest. Both the intensity and the Doppler shifts of the coherent echoes were modulated by the wave.

Compositional changes during ion bombardment

International Nuclear Information System (INIS)

Rehn, L.E.

1988-09-01

Ion irradiation initiates several processes that can alter the composition of the target. This presentation provides an overview of our current understanding of these kinetics processes, which include implantation, sputtering, displacement mixing, radiation-enhanced diffusion, and radiation-induced segregation. The latter two effects can alter the target composition to depths that are substantially greater than the projected ion range. 45 refs., 8 figs

Origin of energetic ions in the polar cusp inferred from ion composition measurements by the Viking satellite

Directory of Open Access Journals (Sweden)

G. Kremser

1995-06-01

Full Text Available The magnetospheric ion composition spectrometer MICS on the Swedish Viking satellite provided measurements of the ion composition in the energy range 10.1 keV/e\\leqE/Q\\leq326.0 keV/e. Data obtained during orbit 842 were used to investigate the ion distribution in the northern polar cusp and its vicinity. The satellite traversed the outer ring current, boundary region, cusp proper and plasma mantle during its poleward movement. H+ and He++ ions were encountered in all of these regions. He+ ions were present only in the ring current. The number of O+ and O++ ions was very small. Heavy high-charge state ions typical for the solar wind were observed for the first time, most of them in the poleward part of the boundary region and in the cusp proper. The H+ ions exhibited two periods with high intensities. One of them, called the BR/CP event, appeared at energies up to 50 keV. It started at the equatorward limit of the boundary region and continued into the cusp proper. Energy spectra indicate a ring current origin for the BR/CP event. Pitch angle distributions show downward streaming of H+ ions at its equatorward limit and upward streaming on the poleward side. This event is interpreted as the result of pitch angle scattering of ring current ions by fluctuations in the magnetopause current layer in combination with poleward convection. The other of the two periods with high H+ ion intensities, called the accelerated ion event, was superimposed on the BR/CP event. It was restricted to energies \\leq15 keV and occurred in the poleward part of the boundary region. This event is regarded as the high-energy tail of magnetosheath ions that were accelerated while penetrating into the magnetosphere. The cusp region thus contains ions of magnetospheric as well as of magnetosheath origin. The appearance of the ions depends, in addition to the ion source, on the magnetic field configuration and dynamic processes inside and close to the cusp.

Composite inorganic ion-exchangers and their applications

International Nuclear Information System (INIS)

Sebesta, F.; John, J.; Motl, A.

1998-01-01

Composite inorganic ion exchangers are described containing modified polyacrylonitrile as the binding polymer. An overview of existing composite ion exchangers is presented, and the universality and assets of the developed procedure of treatment of inorganic ion exchanger powders are highlighted. Examples of applicability of the ion exchangers to the separation and concentration of radionuclides include in particular: wastes from the operation of nuclear power plants, contaminated surface waters and ground water, high level radioactive wastes from spent fuel reprocessing, and wastewaters from uranium ore mining and milling. In addition, composite ion exchangers find use in the monitoring of contamination of the hydrosphere and the environment and in the investigation of radionuclide migration in surface waters and ground water

Adverse Effects of Sporadic Dialysis on Body Composition.

Science.gov (United States)

Workeneh, Biruh; Shypailo, Roman; DeCastro, Iris; Shah, Maulin; Guffey, Danielle; Minard, Charles G; Mitch, William E

2015-01-01

The aim of this study is to analyze the body composition of patients receiving emergent dialysis and compare their body cell mass (BCM) and fat-free mass (FFM) with those of normal subjects. The care of patients receiving sporadic, emergent dialysis treatment is a growing public health concern and the magnitude of muscle wasting that occurs in this population is not known. We used a cross-sectional design with matching to determine differences in total body potassium--an indicator of both BCM and FFM--between emergent dialysis patients and healthy normal subjects. We studied 22 subjects using a 40K counter that measures BCM and FFM and compared them to controls after matching with sex, height and weight. In the matched comparison, BCM and FFM were significantly lower in subjects with end-stage renal disease (ESRD). Unadjusted BCM was 4.7 kg lower and FFM was 8.8 kg lower for those with ESRD compared to those without ESRD (p FFM (7.7 kg) in the ESRD subjects (p = 0.004). After adjusting for age, height, weight and gender, BCM and FFM were lower by 4.2 and 7.8 kg, respectively (p FFM loss over time was significant, with the ESRD subjects demonstrating 2.2 kg per year decline (p = 0.01). We conclude that among other consequences, muscle wasting indicated by decline in BCM and FFM is a significant concern in the growing emergent dialysis population. © 2015 S. Karger AG, Basel.

Occurrence of the blanketing sporadic E layer during the recovery phase of the October 2003 superstorm

Science.gov (United States)

Denardini, Clezio Marcos; Resende, Laysa Cristina Araújo; Moro, Juliano; Chen, Sony Su

2016-05-01

We have routinely monitored the total frequency ( ftEs) and the blanketing frequency ( fbEs) of sporadic E layers with the digital sounder under the magnetic equator in the Brazilian sector. Sporadic layers appear in the equatorial region (Esq) at heights between 90 and 130 km, mainly due to irregularities in the equatorial electrojet current. However, during the recovery phase of the October 2003 superstorm, an anomalous intensification of the ionospheric density that exceeded the normal ambient background values for local time and location was observed. The parameter fbEs rose to almost 7.5 MHz during this event, due to a type "c" blanketing sporadic layer (Esc), which is driven by wind shear. This result is discussed in terms of the atmosphere dynamics based on magnetic signature of the equatorial electrojet current using magnetometer data. Also, using data measured by sensors onboard the Geostationary Operational Environmental Satellite (GOES) 10 we analyze the possible influence of the solar flare-associated X-ray flux as an additional source of ionization.

Equatorial E Region Electric Fields and Sporadic E Layer Responses to the Recovery Phase of the November 2004 Geomagnetic Storm

Science.gov (United States)

Moro, J.; Resende, L. C. A.; Denardini, C. M.; Xu, J.; Batista, I. S.; Andrioli, V. F.; Carrasco, A. J.; Batista, P. P.; Schuch, N. J.

2017-12-01

Equatorial E region electric fields (EEFs) inferred from coherent radar data, sporadic-E (Es) layers observed from a digital ionosonde data, and modeling results are used to study the responses of the equatorial E region over São Luís (SLZ, 2.3°S, 44.2°W, -7° dip angle), Brazil, during the super storm of November 2004. The EEF is presented in terms of the zonal (Ey) and vertical (Ez) components in order to analyze the corresponding characteristics of different types of Es seen in ionograms and simulated with the E region ionospheric model. We bring out the variabilities of Ey and Ez components with storm time changes in the equatorial E region. In addition, some aspects of the electric fields and Es behavior in three cases of weak, very weak, and strong Type II occurrences during the recovery phase of the geomagnetic storm are discussed. The connection between the enhanced occurrence and suppressions of the Type II irregularities and the q-type Es (Esq) controlled by electric fields, with the development or disruption of the blanketing sporadic E (Esb) layers produced by wind shear mechanism, is also presented. The mutual presence of Esq along with the Esb occurrences is a clear indicator of the secular drift of the magnetic equator and hence that of the equatorial electrojet (EEJ) over SLZ. The results show evidence about the EEJ and Es layer electrodynamics and coupling during geomagnetic disturbance time electric fields.

Changes in the composition of brain interstitial ions control the sleep-wake cycle

DEFF Research Database (Denmark)

Ding, Fengfei; O'Donnell, John; Xu, Qiwu

2016-01-01

, and [H+]e as well as the extracellular volume. Local cortical activity of sleeping mice could be readily converted to the stereotypical electroencephalography pattern of wakefulness by simply imposing a change in the extracellular ion composition. Thus, extracellular ions control the state...

The Prion Protein Preference of Sporadic Creutzfeldt-Jakob Disease Subtypes*

Science.gov (United States)

Klemm, Helen M. J.; Welton, Jeremy M.; Masters, Colin L.; Klug, Genevieve M.; Boyd, Alison; Hill, Andrew F.; Collins, Steven J.; Lawson, Victoria A.

2012-01-01

Sporadic Creutzfeldt-Jakob disease (CJD) is the most prevalent manifestation of the transmissible spongiform encephalopathies or prion diseases affecting humans. The disease encompasses a spectrum of clinical phenotypes that have been correlated with molecular subtypes that are characterized by the molecular mass of the protease-resistant fragment of the disease-related conformation of the prion protein and a polymorphism at codon 129 of the gene encoding the prion protein. A cell-free assay of prion protein misfolding was used to investigate the ability of these sporadic CJD molecular subtypes to propagate using brain-derived sources of the cellular prion protein (PrPC). This study confirmed the presence of three distinct sporadic CJD molecular subtypes with PrPC substrate requirements that reflected their codon 129 associations in vivo. However, the ability of a sporadic CJD molecular subtype to use a specific PrPC substrate was not determined solely by codon 129 as the efficiency of prion propagation was also influenced by the composition of the brain tissue from which the PrPC substrate was sourced, thus indicating that nuances in PrPC or additional factors may determine sporadic CJD subtype. The results of this study will aid in the design of diagnostic assays that can detect prion disease across the diversity of sporadic CJD subtypes. PMID:22930754

Impaired proteasome function in sporadic amyotrophic lateral sclerosis.

Science.gov (United States)

Kabashi, Edor; Agar, Jeffrey N; Strong, Michael J; Durham, Heather D

2012-06-01

Abstract The ubiquitin-proteasome system, important for maintaining protein quality control, is compromised in experimental models of familial ALS. The objective of this study was to determine if proteasome function is impaired in sporadic ALS. Proteasomal activities and subunit composition were evaluated in homogenates of spinal cord samples obtained at autopsy from sporadic ALS and non-neurological control cases, compared to cerebellum as a clinically spared tissue. The level of 20S α structural proteasome subunits was assessed in motor neurons by immunohistochemistry. Catalysis of peptide substrates of the three major proteasomal activities was substantially reduced in ALS thoracic spinal cord, but not in cerebellum, accompanied by alterations in the constitutive proteasome machinery. Chymotrypsin-like activity was decreased to 60% and 65% of control in ventral and dorsal spinal cord, respectively, concomitant with reduction in the β5 subunit with this catalytic activity. Caspase- and trypsin-like activities were reduced to a similar extent (46% - 68% of control). Proteasome levels, although generally maintained, appeared reduced specifically in motor neurons by immunolabelling. In conclusion, there are commonalities of findings in sporadic ALS patients and presymptomatic SOD1-G93A transgenic mice and these implicate inadequate proteasome function in the pathogenesis of both familial and sporadic ALS.

Analysis of wave-like oscillations in parameters of sporadic E layer and neutral atmosphere

Czech Academy of Sciences Publication Activity Database

Mošna, Zbyšek; Koucká Knížová, Petra

90-91, SI (2012), s. 172-178 ISSN 1364-6826. [IAGA/ICMA/CAWSES-II TG4 Workshop on Vertical Coupling in the Atmosphere-Ionosphere System /4./. Prague, 14.02.2011-18.02.2011] R&D Projects: GA AV ČR IAA300420704 Institutional support: RVO:68378289 Keywords : Sporadic E * Planetary waves * Tidal waves * Mid-latitude ionosphere Subject RIV: DG - Athmosphere Sciences, Meteorology Impact factor: 1.417, year: 2012 http://www.sciencedirect.com/science/article/pii/S1364682612001186

Analysis of wave-like oscillations in parameters of sporadic E layer and neutral atmosphere

Science.gov (United States)

Mošna, Z.; Koucká Knížová, P.

2012-12-01

The present study mainly concerns the wave-like activity in the ionospheric sporadic E layer (Es) and in the lower lying stratosphere. The proposed analysis involves parameters describing the state of plasma in the sporadic E layer. Critical frequencies foEs and layer heights hEs were measured at the Pruhonice station (50°N, 14.5°E) during summer campaigns 2004, 2006 and 2008. Further, we use neutral atmosphere (temperature data at 10 hPa) data from the same time interval. The analysis concentrates on vertically propagating wave-like structures within distant atmospheric regions. By means of continuous wavelet transform (CWT) we have detected significant wave-like oscillation at periods covering tidal and planetary oscillation domains both in the Es layer parameters (some of them were reported earlier, for instance in works of Abdu et al., 2003; Pancheva and Mitchel, 2004; Pancheva et al., 2003; Šauli and Bourdillon, 2008) and in stratospheric temperature variations. Further analyses using cross wavelet transform (XWT) and wavelet coherence analysis (WTC) show that despite high wave-like activity in a wide period range, there are only limited coherent wave-like bursts present in both spectra. Such common coherent wave bursts occur on periods close to eigen-periods of the terrestrial atmosphere. We suppose that vertical coupling between atmospheric regions realized by vertically propagating planetary waves occurs predominantly on periods close to those of Rossby modes. Analysis of the phase shift between data from distant atmospheric regions reveals high variability and very likely supports the non-linear scenario of the vertical coupling provided by planetary waves.

Origin of energetic ions in the polar cusp inferred from ion composition measurements by the Viking satellite

Directory of Open Access Journals (Sweden)

G. Kremser

Full Text Available The magnetospheric ion composition spectrometer MICS on the Swedish Viking satellite provided measurements of the ion composition in the energy range 10.1 keV/eleqE/Qleq326.0 keV/e. Data obtained during orbit 842 were used to investigate the ion distribution in the northern polar cusp and its vicinity. The satellite traversed the outer ring current, boundary region, cusp proper and plasma mantle during its poleward movement. H⁺ and He⁺⁺ ions were encountered in all of these regions. He⁺ ions were present only in the ring current. The number of O⁺ and O⁺⁺ ions was very small. Heavy high-charge state ions typical for the solar wind were observed for the first time, most of them in the poleward part of the boundary region and in the cusp proper. The H⁺ ions exhibited two periods with high intensities. One of them, called the BR/CP event, appeared at energies up to 50 keV. It started at the equatorward limit of the boundary region and continued into the cusp proper. Energy spectra indicate a ring current origin for the BR/CP event. Pitch angle distributions show downward streaming of H⁺ ions at its equatorward limit and upward streaming on the poleward side. This event is interpreted as the result of pitch angle scattering of ring current ions by fluctuations in the magnetopause current layer in combination with poleward convection. The other of the two periods with high H⁺ ion intensities, called the accelerated ion event, was superimposed on the BR/CP event. It was restricted to energies leq15 keV and occurred in the poleward part of the boundary region. This event is regarded as the high-energy tail of magnetosheath ions that were accelerated while penetrating into the magnetosphere. The cusp region thus contains ions of magnetospheric as well as of magnetosheath origin. The appearance of the ions depends, in addition to the ion source, on the

Ion composition and temperature in the topside ionosphere.

Science.gov (United States)

Brace, L. H.; Dunham, G. S.; Mayr, H. G.

1967-01-01

Particle and energy continuity equations derived and solved by computer method ion composition and plasma temperature measured by Explorer XXII PARTICLE and energy continuity equations derived and solved by computer method for ion composition and plasma temperature measured by Explorer XXII

E parallel B energy-mass spectrograph for measurement of ions and neutral atoms

International Nuclear Information System (INIS)

Funsten, H.O.; McComas, D.J.; Scime, E.E.

1997-01-01

Real-time measurement of plasma composition and energy is an important diagnostic in fusion experiments. The Thomson parabola spectrograph described here utilizes an electric field parallel to a magnetic field (E parallel B) and a two-dimensional imaging detector to uniquely identify the energy-per-charge and mass-per-charge distributions of plasma ions. An ultrathin foil can be inserted in front of the E parallel B filter to convert neutral atoms to ions, which are subsequently analyzed using the E parallel B filter. Since helium exiting an ultrathin foil does not form a negative ion and hydrogen isotopes do, this spectrograph allows unique identification of tritium ions and neutrals even in the presence of a large background of 3 He. copyright 1997 American Institute of Physics

Simulation studies of acceleration of heavy ions and their elemental compositions

International Nuclear Information System (INIS)

Toida, Mieko; Ohsawa, Yukiharu

1996-07-01

By using a one-dimensional, electromagnetic particle simulation code with full ion and electron dynamics, we have studied the acceleration of heavy ions by a nonlinear magnetosonic wave in a multi-ion-species plasma. First, we describe the mechanism of heavy ion acceleration by magnetosonic waves. We then investigate this by particle simulations. The simulation plasma contains four ion species: H, He, O, and Fe. The number density of He is taken to be 10% of that of H, and those of O and Fe are much lower. Simulations confirm that, as in a single-ion-species plasma, some of the hydrogens can be accelerated by the longitudinal electric field formed in the wave. Furthermore, they show that magnetosonic waves can accelerate all the particles of all the heavy species (He, O, and Fe) by a different mechanism, i.e., by the transverse electric field. The maximum speeds of the heavy species are about the same, of the order of the wave propagation speed. These are in good agreement with theoretical prediction. These results indicate that, if high-energy ions are produced in the solar corona through these mechanisms, the elemental compositions of these heavy ions can be similar to that of the background plasma, i.e., the corona

Energetics and structure of the lower E region associated with sporadic E layer

Directory of Open Access Journals (Sweden)

K.-I. Oyama

2008-09-01

Full Text Available The electron temperature (Te, electron density (Ne, and two components of the electric field were measured from the height of 90 km to 150 km by one of the sounding rockets launched during the SEEK-2 campaign. The rocket went through sporadic E layer (Es at the height of 102 km–109 km during ascent and 99 km–108 km during decent, respectively. The energy density of thermal electrons calculated from Ne and Te shows the broad maximum in the height range of 100–110 km, and it decreases towards the lower and higher altitudes, which implies that a heat source exists in the height region of 100 km–110 km. A 3-D picture of Es, that was drawn by using Te, Ne, and the electric field data, corresponded to the computer simulation; the main structure of Es is projected to a higher altitude along the magnetic line of force, thus producing irregular structures of Te, Ne and electric field in higher altitude.

Composite anode for lithium ion batteries

Energy Technology Data Exchange (ETDEWEB)

de Guzman, Rhet C.; Ng, K.Y. Simon; Salley, Steven O.

2018-03-06

A composite anode for a lithium-ion battery is manufactured from silicon nanoparticles having diameters mostly under 10 nm; providing an oxide layer on the silicon nanoparticles; dispersing the silicon nanoparticles in a polar liquid; providing a graphene oxide suspension; mixing the polar liquid containing the dispersed silicone nanoparticles with the graphene oxide suspension to obtain a composite mixture; probe-sonicating the mixture for a predetermined time; filtering the composite mixture to obtain a solid composite; drying the composite; and reducing the composite to obtain graphene and silicon.

The influence of tidal winds in the formation of blanketing sporadic e-layer over equatorial Brazilian region

Science.gov (United States)

Resende, Laysa Cristina Araujo; Batista, Inez Staciarini; Denardini, Clezio Marcos; Batista, Paulo Prado; Carrasco, Alexander José; Andrioli, Vânia Fátima; Moro, Juliano

2018-06-01

This work analysis the blanketing sporadic layers (Esb) behavior over São Luís, Brazil (2° 31‧ S, 44° 16‧ W, dip: -4.80) which is classified as a transition region between equatorial and low-latitude. Hence, some peculiarities can appear as Esb occurrence instead of the common Esq, which is a non-blanketing irregularity layer. The analysis presented here was obtained using a modified version of a theoretical model for the E region (MIRE), which computes the densities of the metallic ions (Fe+ and Mg+) and the densities of the main molecular ions (NO+, O2+, N2+) by solving the continuity and momentum equations for each one of them. In that model, the Es layer physics driven by both diurnal and semidiurnal tidal winds are taken into account and it was extended in height coverage by adding a novel neutral wind model derived from the all-sky meteor radar measurements. Thus, we provide more trustworthy results related to the Es layer formation in the equatorial region. We verified the contribution of each tidal wind component to the Esb layer formation in this equatorial region. Additionally, we compared the Es layer electron density computed by MIRE with the data obtained by using the blanketing frequency parameter (fbEs) deduced from ionograms. The results show that the diurnal component of the tidal wind is more important in the Esb layer formation whereas the semidiurnal component has a little contribution in our simulations. Finally, it was verified that the modified MIRE presented here can be used to study the Esb layers occurrence over the equatorial region in the Brazilian sector.

Graphene-Based Composites as Cathode Materials for Lithium Ion Batteries

Directory of Open Access Journals (Sweden)

Libao Chen

2013-01-01

Full Text Available Owing to the superior mechanical, thermal, and electrical properties, graphene was a perfect candidate to improve the performance of lithium ion batteries. Herein, we review the recent advances in graphene-based composites and their application as cathode materials for lithium ion batteries. We focus on the synthesis methods of graphene-based composites and the superior electrochemical performance of graphene-based composites as cathode materials for lithium ion batteries.

Synthesis, Characterization and Ion Exchange Properties of a New Composite of Inorganic Ion Exchanger： Polyacrylonitrile Cerium（IV） Molybdophosphate%Synthesis, Characterization and Ion Exchange Properties of a New Composite of Inorganic Ion Exchanger： Polyacrylonitrile Cerium（IV） Molybdophosphate

Institute of Scientific and Technical Information of China (English)

Ahmadi, Seyed Javad; Yavari, Ramin; Ashtari, Parviz＇; Gholipour, Vanik; Kamel, Leila; Rakhshandehru, Farokh

2012-01-01

In this work, the synthesis of the composite of cerium（IV） molybdophosphate （CMP） and polyacrylonitrile （PAN） was reported （CMP-PAN）. The material has been characterized by elemental and spectral （FT-IR）, X-ray and thermal （TGA） analysis. Also the size analysis of the composite was done by scanning electron microscopy （SEM）. Its chemical stability in acidic, basic and saline solutions and radiation stability up to 100 kGy total expose dose were assessed. Whereas the synthesized composite has ion exchange properties, its ion exchange capacity and behavior toward several metal ions were also investigated. Further, the distribution coefficients of the metal ions were calculated. Finally, the ability of the synthesized CMP-PAN composite for the decontamination of low level liquid waste （LLLW） was investigated.

Geotail observations of plasma sheet ion composition over 16 years: On variations of average plasma ion mass and O+ triggering substorm model

Science.gov (United States)

Nosé, M.; Ieda, A.; Christon, S. P.

2009-07-01

We examined long-term variations of ion composition in the plasma sheet, using energetic (9.4-212.1 keV/e) ion flux data obtained by the suprathermal ion composition spectrometer (STICS) sensor of the energetic particle and ion composition (EPIC) instrument on board the Geotail spacecraft. EPIC/STICS observations are available from 17 October 1992 for more than 16 years, covering the declining phase of solar cycle 22, all of solar cycle 23, and the early phase of solar cycle 24. This unprecedented long-term data set revealed that (1) the He+/H+ and O+/H+ flux ratios in the plasma sheet were dependent on the F10.7 index; (2) the F10.7 index dependence is stronger for O+/H+ than He+/H+; (3) the O+/H+ flux ratio is also weakly correlated with the ΣKp index; and (4) the He2+/H+ flux ratio in the plasma sheet appeared to show no long-term trend. From these results, we derived empirical equations related to plasma sheet ion composition and the F10.7 index and estimated that the average plasma ion mass changes from ˜1.1 amu during solar minimum to ˜2.8 amu during solar maximum. In such a case, the Alfvén velocity during solar maximum decreases to ˜60% of the solar minimum value. Thus, physical processes in the plasma sheet are considered to be much different between solar minimum and solar maximum. We also compared long-term variation of the plasma sheet ion composition with that of the substorm occurrence rate, which is evaluated by the number of Pi2 pulsations. No correlation or negative correlation was found between them. This result contradicts the O+ triggering substorm model, in which heavy ions in the plasma sheet increase the growth rate of the linear ion tearing mode and play an important role in localization and initiation of substorms. In contrast, O+ ions in the plasma sheet may prevent occurrence of substorms.

Genetics Home Reference: sporadic hemiplegic migraine

Science.gov (United States)

... Home Health Conditions Sporadic hemiplegic migraine Sporadic hemiplegic migraine Printable PDF Open All Close All Enable Javascript ... view the expand/collapse boxes. Description Sporadic hemiplegic migraine is a rare form of migraine headache. Migraines ...

Observations of neutral winds, wind shears, and wave structure during a sporadic-E/QP event

Directory of Open Access Journals (Sweden)

M. F. Larsen

2005-10-01

Full Text Available The second Sporadic E Experiment over Kyushu (SEEK-2 was carried out on 3 August 2002, during an active sporadic-E event that also showed quasi-periodic (QP echoes. Two rockets were launched into the event from Kagoshima Space Center in southern Japan 15 min apart. Both carried a suite of instruments, but the second rocket also released a trimethyl aluminum (TMA trail to measure the neutral winds and turbulence structure. In a number of earlier measurements in similar conditions, large winds and shears that were either unstable or close to instability were observed in the altitude range where the ionization layer occurred. The SEEK-2 wind measurements showed similar vertical structure, but unlike earlier experiments, there was a significant difference between the up-leg and down-leg wind profiles. In addition, wave or billow-like fluctuations were evident in the up-leg portion of the trail, while the lower portion of the down-leg trail was found to have extremely strong turbulence that led to a rapid break-up of the trail. The large east-west gradient in the winds and the strong turbulence have not been observed before. The wind profiles and shears, as well as the qualitative characteristics of the strong turbulence are presented, along with a discussion of the implications of the dynamical features. Keywords. Ionosphere (Mid-latitude ionosphere; Ionospheric irregularities; Electric field and currents

Solar eclipse effects of 22 July 2009 on Sporadic-E

Directory of Open Access Journals (Sweden)

G. Chen

2010-02-01

Full Text Available The total solar eclipse of 22 July 2009, was visible from some regions of China and the intense sporadic-E (Es that broke out during the solar eclipse period over the eastern China provided a unique chance to study solar eclipse effects on the Es-layer. The ground based high-frequency (HF vertical-incidence and oblique-incidence backscatter radio systems in Wuhan and an HF oblique receivers located in Suzhou were operated to detect the Es-layer. The vertical, oblique and backscatter ionograms of 22 and 23 July were recorded, processed and analyzed. The analyzing results show that the critical frequency of Es, the hop number and power of the rays transmitted from Wuhan to Suzhou as well as the Doppler frequency shift of the one-hop oblique-incidence waves reflected by the Es-layer all increased during the solar eclipse period. These variations are displayed in the paper and explained to be induced by the wind-field, which is produced by the powerful meridional air flows from the sunshine region to the moon's shadow.

Solar eclipse effects of 22 July 2009 on Sporadic-E

Directory of Open Access Journals (Sweden)

G. Chen

2010-02-01

Full Text Available The total solar eclipse of 22 July 2009, was visible from some regions of China and the intense sporadic-E (Es that broke out during the solar eclipse period over the eastern China provided a unique chance to study solar eclipse effects on the Es-layer. The ground based high-frequency (HF vertical-incidence and oblique-incidence backscatter radio systems in Wuhan and an HF oblique receivers located in Suzhou were operated to detect the Es-layer. The vertical, oblique and backscatter ionograms of 22 and 23 July were recorded, processed and analyzed. The analyzing results show that the critical frequency of Es, the hop number and power of the rays transmitted from Wuhan to Suzhou as well as the Doppler frequency shift of the one-hop oblique-incidence waves reflected by the Es-layer all increased during the solar eclipse period. These variations are displayed in the paper and explained to be induced by the wind-field, which is produced by the powerful meridional air flows from the sunshine region to the moon's shadow.

Comparison Between Sporadic and Misdiagnosed Sporadic Creutzfeldt-Jakob Disease: A Report of Two Cases.

Science.gov (United States)

Zhao, Xiongfei; Yu, Yingxin; Zhao, Zhiru; Xu, Jiaping

2015-06-01

Definite accurate diagnosis for Creutzfeldt-Jakob disease (CJD) depends on neuropathologic examination of brain biopsy or autopsy. However, transmissible nature makes the invasive examination dangerous. This study was set to determine that the clinical features are for the diagnosis of CJD through a comparison study. We compared clinical features of two cases with initial diagnosis of sporadic CJD. One case was finally diagnosed as definite sporadic CJD. According to World Health Organization diagnosis criteria, the other one, which had been diagnosed as probable sporadic CJD, was confirmed as limbic encephalitis after long-term follow-up. Compared with the case of definite sporadic CJD, the misdiagnosed case did not present typical electroencephalogram (EEG) and diffusion-weighted in magnetic resonance images (DWI) of CJD. However, cerebrospinal fluid in the misdiagnosed patient showed 14-3-3 protein positivity. The patient conditions improved after treatment. Through this case comparison, we conclude that EEG and DWI are necessary for accurate diagnosis of sporadic CJD. Further, long-term follow-up is crucial to diagnosis and treatment of CJD.

A dendrite-suppressing composite ion conductor from aramid nanofibres.

Science.gov (United States)

Tung, Siu-On; Ho, Szushen; Yang, Ming; Zhang, Ruilin; Kotov, Nicholas A

2015-01-27

Dendrite growth threatens the safety of batteries by piercing the ion-transporting separators between the cathode and anode. Finding a dendrite-suppressing material that combines high modulus and high ionic conductance has long been considered a major technological and materials science challenge. Here we demonstrate that these properties can be attained in a composite made from Kevlar-derived aramid nanofibres assembled in a layer-by-layer manner with poly(ethylene oxide). Importantly, the porosity of the membranes is smaller than the growth area of the dendrites so that aramid nanofibres eliminate 'weak links' where the dendrites pierce the membranes. The aramid nanofibre network suppresses poly(ethylene oxide) crystallization detrimental for ion transport, giving a composite that exhibits high modulus, ionic conductivity, flexibility, ion flux rates and thermal stability. Successful suppression of hard copper dendrites by the composite ion conductor at extreme discharge conditions is demonstrated, thereby providing a new approach for the materials engineering of solid ion conductors.

A case study on generation mechanisms of a sporadic sodium layer above Tromsø (69.6° N during a night of high auroral activity

Directory of Open Access Journals (Sweden)

T. Takahashi

2015-08-01

Full Text Available We have quantitatively evaluated generation mechanisms of a sporadic sodium layer (SSL based on observational data obtained by multiple instruments at a high-latitude station: Ramfjordmoen, Tromsø, Norway (69.6° N, 19.2° E. The sodium lidar observed an SSL at 21:18 UT on 22 January 2012. The SSL was observed for 18 min, with a maximum sodium density of about 1.9 × 1010 m−3 at 93 km with a 1.1 km thickness. The European Incoherent Scatter (EISCAT UHF radar observed a sporadic E layer (Es layer above 90 km from 20:00 to 23:00 UT. After 20:00 UT, the Es layer gradually descended and reached 94 km at 21:18 UT when the SSL appeared at the same altitude. In this event, considering the abundance of sodium ions (10 % or less, the Es layer could provide only about 37 % or less of the sodium atoms to the SSL. We have investigated a temporal development of the normal sodium ion layer with a consideration of chemical reactions and the effect of the (southwestward electric field using observational values of the neutral temperature, electron density, horizontal neutral wind, and electric field. This calculation has shown that those processes, including contributions of the Es layer, would provide about 88 % of sodium atoms of the SSL. The effects of meteor absorption and auroral particle sputtering appear to be less important. Therefore, we have concluded that the major source of the SSL was sodium ions in a normal sodium ion layer. Two processes – namely the downward transportation of sodium ions from a normal sodium ion layer due to the electric field and the additional supply of sodium ions from the Es layer under relatively high electron density conditions (i.e., in the Es layer – played a major role in generating the SSL in this event. Furthermore, we have found that the SSL was located in a lower-temperature region and that the temperature inside the SSL did not show any remarkable temperature enhancements.

Introduction to Sporadic Groups

Directory of Open Access Journals (Sweden)

Luis J. Boya

2011-01-01

Full Text Available This is an introduction to finite simple groups, in particular sporadic groups, intended for physicists. After a short review of group theory, we enumerate the 1+1+16=18 families of finite simple groups, as an introduction to the sporadic groups. These are described next, in three levels of increasing complexity, plus the six isolated ''pariah'' groups. The (old five Mathieu groups make up the first, smallest order level. The seven groups related to the Leech lattice, including the three Conway groups, constitute the second level. The third and highest level contains the Monster group M, plus seven other related groups. Next a brief mention is made of the remaining six pariah groups, thus completing the 5+7+8+6=26 sporadic groups. The review ends up with a brief discussion of a few of physical applications of finite groups in physics, including a couple of recent examples which use sporadic groups.

Strong Sporadic E Occurrence Detected by Ground-Based GNSS

Science.gov (United States)

Sun, Wenjie; Ning, Baiqi; Yue, Xinan; Li, Guozhu; Hu, Lianhuan; Chang, Shoumin; Lan, Jiaping; Zhu, Zhengping; Zhao, Biqiang; Lin, Jian

2018-04-01

The ionospheric sporadic E (Es) layer has significant impact on radio wave propagation. The traditional techniques employed for Es layer observation, for example, ionosondes, are not dense enough to resolve the morphology and dynamics of Es layer in spatial distribution. The ground-based Global Navigation Satellite Systems (GNSS) technique is expected to shed light on the understanding of regional strong Es occurrence, owing to the facts that the critical frequency (foEs) of strong Es structure is usually high enough to cause pulse-like disturbances in GNSS total electron content (TEC), and a large number of GNSS receivers have been deployed all over the world. Based on the Chinese ground-based GNSS networks, including the Crustal Movement Observation Network of China and the Beidou Ionospheric Observation Network, a large-scale strong Es event was observed in the middle latitude of China. The strong Es shown as a band-like structure in the southwest-northeast direction extended more than 1,000 km. By making a comparative analysis of Es occurrences identified from the simultaneous observations by ionosondes and GNSS TEC receivers over China middle latitude statistically, we found that GNSS TEC can be well employed to observe strong Es occurrence with a threshold value of foEs, 14 MHz.

Generation of H-, D- ions on composite surfaces with application to surface/plasma ion source systems

International Nuclear Information System (INIS)

Hiskes, J.R.; Karo, A.M.; Wimmer, E.; Freeman, A.J.; Chubb, S.R.

1983-01-01

We review some salient features of the experimental and theoretical data pertaining to hydrogen negative ion generation on minimum-work-function composite surfaces consisting of Cs/transition metal substrates. Cesium or hydrogen ion bombardment of a cesium-activated negatively-biased electrode exposed to a cesium-hydrogen discharge results in the release of hydrogen negative ions. These ions originate through desorbtion of hydrogen particles by incident cesium ions, desorbtion by incident hydrogen ions, and by backscattering of incident hydrogen. Each process is characterized by a specific energy and angular distribution. The calculation of ion formation in the crystal selvage region is discussed for different approximations to the surface potential. An ab initio, all-electron, local density functional model for the composite surface electronics is discussed

Analysis of Ion Composition Estimation Accuracy for Incoherent Scatter Radars

Science.gov (United States)

Martínez Ledesma, M.; Diaz, M. A.

2017-12-01

The Incoherent Scatter Radar (ISR) is one of the most powerful sounding methods developed to estimate the Ionosphere. This radar system determines the plasma parameters by sending powerful electromagnetic pulses to the Ionosphere and analyzing the received backscatter. This analysis provides information about parameters such as electron and ion temperatures, electron densities, ion composition, and ion drift velocities. Nevertheless in some cases the ISR analysis has ambiguities in the determination of the plasma characteristics. It is of particular relevance the ion composition and temperature ambiguity obtained between the F1 and the lower F2 layers. In this case very similar signals are obtained with different mixtures of molecular ions (NO2+ and O2+) and atomic oxygen ions (O+), and consequently it is not possible to completely discriminate between them. The most common solution to solve this problem is the use of empirical or theoretical models of the ionosphere in the fitting of ambiguous data. More recent works take use of parameters estimated from the Plasma Line band of the radar to reduce the number of parameters to determine. In this work we propose to determine the error estimation of the ion composition ambiguity when using Plasma Line electron density measurements. The sensibility of the ion composition estimation has been also calculated depending on the accuracy of the ionospheric model, showing that the correct estimation is highly dependent on the capacity of the model to approximate the real values. Monte Carlo simulations of data fitting at different signal to noise (SNR) ratios have been done to obtain valid and invalid estimation probability curves. This analysis provides a method to determine the probability of erroneous estimation for different signal fluctuations. Also it can be used as an empirical method to compare the efficiency of the different algorithms and methods on when solving the ion composition ambiguity.

Technique for increasing dynamic range of space-borne ion composition instruments

International Nuclear Information System (INIS)

Burch, J.L.; Miller, G.P.; Santos, A. de los; Pollock, C.J.; Pope, S.E.; Valek, P. W.; Young, D.T.

2005-01-01

The dynamic range of ion composition spectrometers is limited by several factors, including saturation of particle counters and spillover of signals from highly dominant species into channels tuned to minor species. Instruments designed for composition measurements of hot plasmas in space can suffer greatly from both of these problems because of the wide energy range required and the wide disparity in fluxes encountered in various regions of interest. In order to detect minor ions in regions of very weak fluxes, geometry factors need to be as large as possible within the mass and volume resources available. As a result, problems with saturation by the dominant fluxes and spillover to minor-ion channels in plasma regions with intense fluxes become especially acute. This article reports on a technique for solving the dynamic-range problem in the few eV to several keV energy/charge range that is of central importance for space physics research where the dominant ion is of low mass/charge (typically H + ), and the minor ions are of higher mass/charge (typically O + ). The technique involves employing a radio-frequency modulation of the deflection electric field in the back section of an electrostatic analyzer in a time-of-flight instrument. This technique is shown to reduce H + counts by a controllable amount of up to factors of 1000 while reducing O + counts by only a few percent that can be calibrated

Sporadic Fatal Insomnia in an Adolescent

Science.gov (United States)

Blase, Jennifer L.; Cracco, Laura; Schonberger, Lawrence B.; Maddox, Ryan A.; Cohen, Yvonne; Cali, Ignazio

2014-01-01

The occurrence of sporadic prion disease among adolescents is extremely rare. A prion disease was confirmed in an adolescent with disease onset at 13 years of age. Genetic, neuropathologic, and biochemical analyses of the patient’s autopsy brain tissue were consistent with sporadic fatal insomnia, a type of sporadic prion disease. There was no evidence of an environmental source of infection, and this patient represents the youngest documented case of sporadic prion disease. Although rare, a prion disease diagnosis should not be discounted in adolescents exhibiting neurologic signs. Brain tissue testing is necessary for disease confirmation and is particularly beneficial in cases with an unusual clinical presentation. PMID:24488737

Composition and temporal behavior of ambient ions in the boreal forest

Directory of Open Access Journals (Sweden)

M. Ehn

2010-09-01

Full Text Available A recently developed atmospheric pressure interface mass spectrometer (APi-TOF measured the negative and positive ambient ion composition at a boreal forest site. As observed in previous studies, the negative ions were dominated by strong organic and inorganic acids (e.g. malonic, nitric and sulfuric acid, whereas the positive ions consisted of strong bases (e.g. alkyl pyridines and quinolines. Several new ions and clusters of ions were identified based on their exact masses, made possible by the high resolution, mass accuracy and sensitivity of the APi-TOF. Time series correlograms aided in peak identification and assigning the atomic compositions to molecules. Quantum chemical calculations of proton affinities and cluster stabilities were also used to confirm the plausibility of the assignments. Acids in the gas phase are predominantly formed by oxidation in the gas phase, and thus the concentrations are expected to vary strongly between day and night. This was also the case in this study, where the negative ions showed strong diurnal behavior, whereas the daily changes in the positive ions were considerably smaller. A special focus in this work was the changes in the ion distributions occurring during new particle formation events. We found that sulfuric acid, together with its clusters, dominated the negative ion spectrum during these events. The monomer (HSO₄⁻ was the largest peak, together with the dimer (H₂SO₄ · HSO₄⁻ and trimer ((H₂SO₄₂ · HSO₄⁻. SO₅⁻ also tracked HSO₄⁻ at around 20% of the HSO₄⁻ concentration at all times. During the strongest events, the tetramer and a cluster with the tetramer and ammonia were also detected. Quantum chemical calculations predict that sulfuric acid clusters containing ammonia are much more stable when

On the influence of solar activity on the mid-latitude sporadic E layer

Science.gov (United States)

Pezzopane, Michael; Pignalberi, Alessio; Pietrella, Marco

2015-09-01

To investigate the influence of solar cycle variability on the sporadic E layer (Es), hourly measurements of the critical frequency of the Es ordinary mode of propagation, foEs, and of the blanketing frequency of the Es layer, fbEs, recorded from January 1976 to December 2009 at the Rome (Italy) ionospheric station (41.8° N, 12.5° E), were examined. The results are: (1) a high positive correlation between the F10.7 solar index and foEs as well as between F10.7 and fbEs, both for the whole data set and for each solar cycle separately, the correlation between F10.7 and fbEs being much higher than the one between F10.7 and foEs; (2) a decreasing long-term trend of the F10.7, foEs and fbEs time series, with foEs decreasing more rapidly than F10.7 and fbEs; (3) clear and statistically significant peaks at 11 years in the foEs and fbEs time series, inferred from Lomb-Scargle periodograms.

A statistical study of sporadic sodium layer observed by Sodium lidar at Hefei (31.8° N, 117.3° E

Directory of Open Access Journals (Sweden)

X.-K. Dou

2009-06-01

Full Text Available Sodium lidar observations of sporadic sodium layers (SSLs during the past 3 years at a mid-latitude location (Hefei, China, 31.8° N, 117.3° E are reported in this paper. From 64 SSL events detected in about 900 h of observation, an SSL occurrence rate of 1 event every 14 h at our location was obtained. This result, combined with previous studies, reveals that the SSL occurrence can be relatively frequent at some mid-latitude locations. Statistical analysis of main parameters for the 64 SSL events was performed. By examining the corresponding data from an ionosonde, a considerable correlation was found with a Pearson coefficient of 0.66 between seasonal variations of SSL and those of sporadic E (Es during nighttime, which was in line with the research by Nagasawa and Abo (1995. From comparison between observations from the University of Science and Technology of China (USTC lidar and from Wuhan Institute of Physics and Mathematics (WIPM lidar (Wuhan, China, 31° N, 114° E, the minimum horizontal range for some events was estimated to be over 500 km.

Removal of Cu 2+ Ions from Aqueous Medium Using Clinoptilolite/Emeraldine Base Composite

Directory of Open Access Journals (Sweden)

Silviya I. Lavrova

2016-12-01

Full Text Available The aim of this study was to investigate the removal efficiency of in situ synthesized composites consisted of emeraldine base and clinoptilolite on copper ions removal from aqueous medium. Two composite materials (Composite I and Composite II with different quantity of clinoptilolite were synthesised. The influence of the composite dosage, the contact time and the initial copper ions concentration has been studied. The results show that the significant removal of the copper ions becomes at the first minute of the contact between the composite material and the aqueous medium and the longer contact time leads to increasing of the copper ions removal. The removal efficiency at the 1st minute was 57.5% and 77.3% using Composite Iand Composite II, respectively. Maximum removal efficiency of 87.3% and 96.8% was achieved at the same dosage of Composite I and Composite II, respectively, at contact time of 360 minutes and temperature of 24 °C.

The interaction between stratospheric monthly mean regional winds and sporadic-E

International Nuclear Information System (INIS)

Çetin, Kenan; Korlaelçi, Serhat; Özcan, Osman

2017-01-01

In the present study, a statistical investigation is carried out to explore whether there is a relationship between the critical frequency (foEs) of the sporadic-E layer that is occasionally seen on the E region of the ionosphere and the quasi-biennial oscillation (QBO) that flows in the east–west direction in the equatorial stratosphere. Multiple regression model as a statistical tool was used to determine the relationship between variables. In this model, the stationarity of the variables (foEs and QBO) was firstly analyzed for each station (Cocos Island, Gibilmanna, Niue Island, and Tahiti). Then, a co-integration test was made to determine the existence of a long-term relationship between QBO and foEs. After verifying the presence of a long-term relationship between the variables, the magnitude of the relationship between variables was further determined using the multiple regression model. As a result, it is concluded that the variations in foEs were explainable with QBO measured at 10 hPa altitude at the rate of 69%, 94%, 79%, and 58% for Cocos Island, Gibilmanna, Niue Island, and Tahiti stations, respectively. It is observed that the variations in foEs were explainable with QBO measured at 70 hPa altitude at the rate of 66%, 69%, 53%, and 47% for Cocos Island, Gibilmanna, Niue Island, and Tahiti stations, respectively. (paper)

Structure-phase composition and nano hardness of chrome-fullerite-chrome films irradiated by boron ions

International Nuclear Information System (INIS)

Baran, L.V.

2015-01-01

By methods of atomic force microscopy, X-ray diffraction and nano indentation the research of change of structure phase composition and nano hardness of the chrome - fullerite - chrome films, subjected to implantation by B + ions (E = 80 keV, F = 5*10 17 ions/cm 2 ) are submitted. It is established, that as a result of Boron ion implantation of the chrome - fullerite - chrome films, chrome and fullerite inter fusion on sues, that is the solid-phase interaction and as a result of which forms the heterophase with increased nano hardness. (authors)

The GOES-16 Energetic Heavy Ion Sensor (EHIS) Ion Composition and Flux Measurements

Science.gov (United States)

Connell, J. J.; Lopate, C.

2017-12-01

The Energetic Heavy Ion Sensor (EHIS) was built by the University of New Hampshire, subcontracted to Assurance Technology Corporation, as part of the Space Environmental In-Situ Suite (SEISS) on the new GOES-16 satellite (formerly GOES-R) in Geostationary orbit. EHIS measures energetic ions over the range 10-200 MeV for protons, and energy ranges for heavy ions corresponding to the same stopping range (e.g., 19-207 MeV/u for carbon and 38-488 MeV/u for iron). EHIS uses the Angle Detecting Inclined Sensors (ADIS) technique to provide single-element charge resolution. Though on an operational mission for Space Weather monitoring, EHIS can thus provide a new source of high quality Solar Particle Event (SPE) data for science studies. With a high rate of on-board processing ( 2000 events/s), EHIS will provide exceptional statistics for ion composition measurements in large SPEs. For the GOES Level 1-B and Level 2 data products, heavy ions are distinguished in EHIS using pulse-height analysis with on-board processing producing charge histograms for five energy bands. Fits to these data are normalized to priority rate data on the ground. The instrumental cadence for histograms is 1 minute and the primary Level 1-B heavy ion data products are 1-minute and 5-minute averages. We discuss the preliminary EHIS heavy ion data results which show elemental peaks from H to Fe, with peaks for the isotopes D and 3He. (GOES-16 was launched in 19 November, 2016 and data has, though July 2017, been dominated by Galactic Cosmic Rays.) The EHIS instrument development project was funded by NASA under contract NNG06HX01C.

Stress analysis in cylindrical composition-gradient electrodes of lithium-ion battery

Science.gov (United States)

Zhong, Yaotian; Liu, Yulan; Wang, B.

2017-07-01

In recent years, the composition-gradient electrode material has been verified to be one of the most promising materials in lithium-ion battery. To investigate diffusion-induced stresses (DIS) generated in a cylindrical composition-gradient electrode, the finite deformation theory and the stress-induced diffusion hypothesis are adopted to establish the constitutive equations. Compared with stress distributions in a homogeneous electrode, the increasing forms of Young's modulus E(R) and partial molar volume Ω(R) from the electrode center to the surface along the radial direction drastically increase the maximal magnitudes of hoop and axial stresses, while both of the decreasing forms are able to make the stress fields smaller and flatter. Also, it is found that the slope of -1 for E(R) with that of -0.5 for Ω(R) is a preferable strategy to prevent the inhomogeneous electrode from cracking, while for the sake of protecting the electrode from compression failure, the optimal slope for inhomogeneous E(R) and the preferential one for Ω(R) are both -0.5. The results provide a theoretical guidance for the design of composition-gradient electrode materials.

Adult onset sporadic ataxias: a diagnostic challenge

Directory of Open Access Journals (Sweden)

Orlando Graziani Povoas Barsottini

2014-03-01

Full Text Available Patients with adult onset non-familial progressive ataxia are classified in sporadic ataxia group. There are several disease categories that may manifest with sporadic ataxia: toxic causes, immune-mediated ataxias, vitamin deficiency, infectious diseases, degenerative disorders and even genetic conditions. Considering heterogeneity in the clinical spectrum of sporadic ataxias, the correct diagnosis remains a clinical challenge. In this review, the different disease categories that lead to sporadic ataxia with adult onset are discussed with special emphasis on their clinical and neuroimaging features, and diagnostic criteria.

Investigation of the composition of an ion beam produced using a multi arc ion source

Energy Technology Data Exchange (ETDEWEB)

Engelko, V [Efremov Institute of Electrophysical Apparatus, St. Petersburg (Russian Federation); Giese, H; Schalk, S [Forschungszentrum Karlsruhe (Germany). INR; Mishin, M; Tsibin, O Y [St. Petersburg State Technical Univ. (Russian Federation)

1997-12-31

Complementing the diode and beam transport optimization studies currently performed at FZK Karlsruhe on the proton-beam-facility PROFA, supplementary investigations were run at the St. Petersburg State University, focusing on ion beam divergence and composition measurements using the TOF techniques. To ensure direct transferability of the results to the PROFA facility, these measurements were made on a scaled-down replica of the PROFA diode, comprising an array of small polyethylene flash-over plasma sources and a grid extraction system. Only the results of the beam composition measurements are presented, and the following conclusions are made: (i) The ion beam contains H and C ions and heavier constituents that remain to be identified. (ii) The beam composition changes significantly with the total number of shots: While H{sup +} ions predominated in the starting phase of the experiments, heavier components outweighed them later on, presumably due to hydrogen depletion of the surface layer of the anode polyethylene units. (iii) Reconditioning of the polyethylene units may be possible by running the diode at higher currents (self-cleaning) or by cutting off a surface layer. (author). 7 figs., 3 refs.

A new identification method for energetic ion ΔE-E telescopes

International Nuclear Information System (INIS)

Martin, Cesar; Bronchalo, Enrique; Medina, Jose

2007-01-01

A new ion identification method for ΔE-E telescopes is presented. The method works by counting data points under ΔE(E) curves on ΔE-E diagrams. These curves are obtained by simulating the telescope response to a flux of energetic ions. The method is checked against three published methods applied to several experimental data sets

A new identification method for energetic ion {delta}E-E telescopes

Energy Technology Data Exchange (ETDEWEB)

Martin, Cesar [Departamento de Fisica, Universidad de Alcala, 28871 Alcala de Henares, Madrid (Spain); Institut fuer Experimentelle und Angewandte Physik, Christian-Albrechts, Universitaet zu Kiel, 24118 Kiel (Germany); Bronchalo, Enrique [Departamento de Fisica, Universidad de Alcala, 28871 Alcala de Henares, Madrid (Spain); Departamento de Fisica y Arquitectura de Computadores, Universidad Miguel Hernandez, Avda. Universidad s/n, 03202 Elche, Alicante (Spain)], E-mail: ebronchalo@umh.es; Medina, Jose [Departamento de Fisica, Universidad de Alcala, 28871 Alcala de Henares, Madrid (Spain)

2007-11-21

A new ion identification method for {delta}E-E telescopes is presented. The method works by counting data points under {delta}E(E) curves on {delta}E-E diagrams. These curves are obtained by simulating the telescope response to a flux of energetic ions. The method is checked against three published methods applied to several experimental data sets.

Scintillation screen applications in a vacuum arc ion source with composite hydride cathode

Science.gov (United States)

Wang, X. H.; Tuo, X. G.; Yang, Z.; Peng, Y. F.; Li, J.; Lv, H. Y.; Li, J. H.; Long, J. D.

2018-05-01

Vacuum arc ion source with composite hydride cathode was developed to produce intense ion beams which can be applied in particle accelerator injections. Beam profile and beam composition are two fundamental parameters of the beam for the vacuum arc ion source in such specific applications. An aluminum-coated scintillation screen with an ICCD camera readout was used to show the space-time distribution of the beam directly. A simple magnetic analysis assembly with the scintillation screen shows the beam composition information of this kind ion source. Some physical and technical issues are discussed and analyzed in the text.

Metal hydride compositions and lithium ion batteries

Energy Technology Data Exchange (ETDEWEB)

Young, Kwo; Nei, Jean

2018-04-24

Heterogeneous metal hydride (MH) compositions comprising a main region comprising a first metal hydride and a secondary region comprising one or more additional components selected from the group consisting of second metal hydrides, metals, metal alloys and further metal compounds are suitable as anode materials for lithium ion cells. The first metal hydride is for example MgH.sub.2. Methods for preparing the composition include coating, mechanical grinding, sintering, heat treatment and quenching techniques.

Application of Some Synthesized Polymeric Composite Resins for Removal of Some Metal Ions

International Nuclear Information System (INIS)

El-Zahhhar, A.A.; Abdel-Aziz, H.M.; Siyam, T.

2005-01-01

The ion-exchange and sorption characteristic of new polymeric composite resins, prepared by gamma radiation were experimentally studied. The composite resins shows high uptake for Co(II) and Eu(III) ions in aqueous solutions in wide range of ph. The selectivity of the resins to Co (II) or Eu (III) species in the presence of some competing ions and complexing agents (as Na + , Fe 3+ , EDTA Na 2 , etc.) was compared. Various factors that could affect the sorption behaviors of metal ions (Co (II) and Eu (III)) on the prepared polymeric composite resins were studied such as ionic strength, Contact time, volume mass ratio

Signals for compositeness in e-e+→e-e+ and e-e+→μ-μ+

International Nuclear Information System (INIS)

Bars, I.; Gunion, J.F.; Kwan, M.

1986-01-01

Theories in which leptons are composite lead to additional contributions (beyond those from the standard model) to the amplitudes for e - e + →e - e + and e - e + →μ - μ + . Detailed models, constructed by analogy between QCD and compositeness/precolor interactions lead to specific forms for these extra terms. We demonstrate that compositeness scales M as high as 4--7 TeV may be probed using e - e + collision machines currently available and planned for the near future. Sensitivity to the type of composite model and its parity-violation structure is demonstrated. In particular we point out that there are no standard-model contributions to the scattering e - e + →μ - μ + when the incoming e - and e + both have the same helicity. Observation of a nonzero cross section in such a helicity scattering state is prima facie evidence of flavor-changing vector currents in the t channel or scalar currents connecting the e and μ lepton sectors in the s channel

New Composite Sorbents for Caesium and Strontium Ions Sorption

Directory of Open Access Journals (Sweden)

Mykola Kartel

2017-06-01

Full Text Available Composite lignocellulose-inorganic sorbents derived from plant residues of agriculture and food industry, modified with ferrocyanides of d-metals and hydrated antimony pentoxide were prepared. Caesium and strontium ions removal from water was tested by radiotracer method. Sorption of heavy metal ions, methylene blue, gelatin, vitamin B12 was also studied.

Ion Composition of Comet 19P/Borrelly as Measured by the PEPE Ion Mass Spectrometer on DS1

Science.gov (United States)

Nordholt, J. E.; Reisenfeld, D. B.; Wiens, R. C.; Gary, P.

2002-12-01

Cometary compositions are of great interest because they hold important clues to the formation of the outer solar system, and to the sources of volatiles in the solar system, including the terrestrial planets. In order to understand the primordial compositions of cometary nuclei, it is important to also understand their evolution, as many of the comets most accessible to spacecraft are highly evolved. It is also important to understand the ion and neutral chemistry that occurs in the coma surrounding the nucleus if the coma ion composition is to be used to determine the original composition of the nucleus. Deep Space One (DS1) was only the second spacecraft, after Giotto, to use an ion mass-resolving instrument to explore cometary coma compositions in-situ, which it did during the flyby of Comet Borrelly on September 22, 2001. Borrelly is significantly more evolved than Halley. In addition, the encounter occurred at a significantly greater distance from the sun (1.36 AU vs 0.9 AU for Giotto at Halley). The Plasma Experiment for Planetary Exploration (PEPE) on board DS1 was capable of resolving electron and ion energy, angle of incidence, and ion mass composition. The PEPE ion data from the seven minutes surrounding closest approach (2171 km) have been extensively analyzed. The instrument response was modeled using SIMION and TRIM codes for all of the major species through 20 AMU plus CO (at its operating voltage PEPE was very insensitive to heavier molecules). Chi-squared minimization analysis is being carried out to determine the best fit and the uncertainties. Preliminary results for the predominant heavy ions are OH+ at (72 +/- 9)% of the total water-group ion density, H2O+ at (25 +/- 7)%, CH3+ at (5 +/- 3)%, and O+ at (4 +/- 5)%. Uncertainties are quoted at the 90% confidence level. Comparison with reported Halley compositions from Giotto shows that Borrelly clearly has a lower H3O+ abundance (< 9%), consistent with a more evolved comet. The presence of

Composition and energy spectrum variations of auroral ions

International Nuclear Information System (INIS)

Lynch, J.; Leach, R.; Pulliam, D.; Scherb, F.

1977-01-01

We have detected H + ,O + , and He ++ ions with E/q up to 20 keV/charge in a hydrogen aurora over Churchill, Manitoba, during the flight of a Javelin sounding rocket on February 11, 1975, We observed several examples of different types of ion events. One type consisted of bursts of H + and O + ions which arrived simultaneously at all energies within the range of the E/q analyzer. These events were apparently of local origin (distance + ions (O + /H + approximately-greater-than30%). A second type of event consisted of bursts of enhanced H + counting rates but no O + ions. The dispersion in time of the energy spectrum was consistent with an injection and acceleration site located at about 20 R/sub E/ from the earth. An enhancement of the He ++ counting rates was associated with these events, but the He ++ data are of limited statistical significance. A third type of event, consisting of short bursts of H + ions with wide energy spreads, was observed in association with an event in which the energy of the H + ions showed time dispersion. We interpret these short H + bursts as due to ions trapped in traveling waves generated by an explosive injection of plasma in the earth's magnetotail

Composition of heavy ions in solar energetic particle events

International Nuclear Information System (INIS)

Fan, C.Y.; Gloeckler, G.

1983-01-01

The elemental, charge state, and isotopic composition of approximately 1 to 20 MeV per nucleon ions in solar energetic particle (SEP) events was determined and current understanding of the nature of solar and interplanetary processes which may explain the observations are outlined. The composition within individual SEP events may vary both with time and energy, and will in general be different from that in other SEP events. Average values of relative abundances measured in a large number of SEP events, however are found to be roughly energy independent in the approximately 1 to approximately 20 MeV per nucleon range, and show a systematic deviation from photospheric abundances which seem to be organized in terms of the first ionization potential of the ion. Direct measurements of the charge states of SEPs have revealed the surprisingly common presence of energetic He(+) along with heavy ions with typical coronal ionization states. High resolution measurements of isotopic abundance ratios in a small number of SEP events show these to be consistent with the universal composition except for the puzzling overabundance of the SEP Ne-22 relative to this isotopes ratio in the solar wind

An experimental study of the ion chemistry and thermal balance in the E- and F-regions above Wallops Island

Science.gov (United States)

Brace, L. H.; Mayr, H. G.; Pharo, M. W., III; Scott, L. R.; Taylor, H. A., Jr.

1971-01-01

E and F region positive ion composition, electron concentration and thermal balance vertical profile, discussing ionizing radiation spectrum, plasma cooling, primary chemical reaction rates and ionospheric formation

Composition of heavy ions in solar energetic particle events

International Nuclear Information System (INIS)

Fan, C.Y.; Gloeckler, G.

1983-01-01

Recent advances in determining the elemental, charge state, and isotopic composition of approximatelt 1 to 20 MeV per nucleon ions in solar energetic particle (SEP) events and outline our current understanding of the nature of solar and interplanetary processes which may explain the observations. Average values of relative abundances measured in a large number of SEP events were found to be roughly energy independent in the approx. 1 to approx. 20 MeV per nucleon range, and showed a systematic deviation from photospheric abundances which seems to be organized in terms of the first ionization potential of the ion. Direct measurements of the charge states of SEPs revealed the surprisingly common presence of energetic He(+) along with heavy ion with typically coronal ionization states. High resolution measurements of isotopic abundance ratios in a small number of SEP events showed these to be consistent with the universal composition except for the puzzling overabundance of the SEP(22)Ne/(20)Ne relative to this isotopes ratio in the solar wind. The broad spectrum of observed elemental abundance variations, which in their extreme result in composition anomalies characteristic of (3)He rich, heavy ion rich and carbon poor SEP events, along with direct measurements of the ionization states of SEPs provided essential information on the physical characteristics of, and conditions in the source regions, as well as important constraints to possible models for SEP production

Dielectric functions, chemical and atomic compositions of the near surface layers of implanted GaAs by In+ ions

Science.gov (United States)

Kulik, M.; Kołodyńska, D.; Bayramov, A.; Drozdziel, A.; Olejniczak, A.; Żuk, J.

2018-06-01

The surfaces of (100) GaAs were irradiated with In+ ions. The implanted samples were isobaric annealed at 800 °C and then of dielectric function, the surface atomic concentrations of atoms and also the chemical composition of the near surface layers in these implanted semiconductor samples were obtained. The following investigation methods were used: spectroscopic ellipsometry (SE), Rutherford backscattering spectrometry analyses (RBSA) and X-ray photoelectron spectroscopy (XPS) in the study of the above mentioned quantities, respectively. The change of the shape spectra of the dielectric functions at about 3.0 eV phonon energy, diffusion of In+ ions as well as chemical composition changes were observed after ion implantation and the thermal treatment. Due to displacement of Ga ions from GaAs by the In+ ions the new chemical compound InAs was formed. The relative amounts Ga2O3 and As2O3 ratio increase in the native oxide layers with the fluences increase after the thermal treatment of the samples. Additionally, it was noticed that the quantities of InO2 increase with the increasing values of the irradiated ions before thermal treatment.

Ion beam modifications of near-surface compositions in ternary alloys

International Nuclear Information System (INIS)

Lam, N.Q.; Tang, S.; Yacout, A.M.; Rehn, L.E.; Stubbins, J.F.

1990-11-01

Changes in the surface and subsurface compositions of ternary alloys during elevated-temperature sputtering with inert-gas ions were investigated. Theoretically, a comprehensive kinetic model which includes all the basic processes, such as preferential sputtering, displacement mixing, Gibbsian segregation, radiation-enhanced diffusion and radiation-induced segregation, was developed. This phenomenological approach enabled to predict the effects of each individual process or of a combination of processes on the compositional modification in model alloys. Experimentally, measurements of compositional changes at the surface of a Ag-40at%Au -- 20at%Cu alloy during 3-keV Ne + bombardment at various temperatures were made, using ion scattering spectroscopy. These measurements were interpreted on the basis of the results of theoretical modeling. 8 refs., 2 figs

Updated clinical diagnostic criteria for sporadic Creutzfeldt-Jakob disease

Science.gov (United States)

Kallenberg, K.; Summers, D. M.; Romero, C.; Taratuto, A.; Heinemann, U.; Breithaupt, M.; Varges, D.; Meissner, B.; Ladogana, A.; Schuur, M.; Haik, S.; Collins, S. J.; Jansen, Gerard H.; Stokin, G. B.; Pimentel, J.; Hewer, E.; Collie, D.; Smith, P.; Roberts, H.; Brandel, J. P.; van Duijn, C.; Pocchiari, M.; Begue, C.; Cras, P.; Will, R. G.; Sanchez-Juan, P.

2009-01-01

Several molecular subtypes of sporadic Creutzfeldt–Jakob disease have been identified and electroencephalogram and cerebrospinal fluid biomarkers have been reported to support clinical diagnosis but with variable utility according to subtype. In recent years, a series of publications have demonstrated a potentially important role for magnetic resonance imaging in the pre-mortem diagnosis of sporadic Creutzfeldt–Jakob disease. Magnetic resonance imaging signal alterations correlate with distinct sporadic Creutzfeldt–Jakob disease molecular subtypes and thus might contribute to the earlier identification of the whole spectrum of sporadic Creutzfeldt–Jakob disease cases. This multi-centre international study aimed to provide a rationale for the amendment of the clinical diagnostic criteria for sporadic Creutzfeldt–Jakob disease. Patients with sporadic Creutzfeldt–Jakob disease and fluid attenuated inversion recovery or diffusion-weight imaging were recruited from 12 countries. Patients referred as ‘suspected sporadic Creutzfeldt–Jakob disease’ but with an alternative diagnosis after thorough follow up, were analysed as controls. All magnetic resonance imaging scans were assessed for signal changes according to a standard protocol encompassing seven cortical regions, basal ganglia, thalamus and cerebellum. Magnetic resonance imaging scans were evaluated in 436 sporadic Creutzfeldt–Jakob disease patients and 141 controls. The pattern of high signal intensity with the best sensitivity and specificity in the differential diagnosis of sporadic Creutzfeldt–Jakob disease was identified. The optimum diagnostic accuracy in the differential diagnosis of rapid progressive dementia was obtained when either at least two cortical regions (temporal, parietal or occipital) or both caudate nucleus and putamen displayed a high signal in fluid attenuated inversion recovery or diffusion-weight imaging magnetic resonance imaging. Based on our analyses, magnetic

Metallic ions in the upper atmosphere

International Nuclear Information System (INIS)

Kumar, S.

1979-01-01

During the past 20 years considerable progress has been made in establishing the presence of metallic ions in the sporadic E layers at mid latitudes and as discrete patches at high altitudes in the equatorial ionosphere. The E-region observations have been based on rocket flights, which represent local conditions faithfully. But the global distribution of metallic ions and variations relating to changes in season, local time, magnetic activity, etc., which require satellite data, have been largely unexamined. This work presents a few aspects of this missing global distribution over an altitude range of 100 to 1000 km, using the data from AE-C, AE-D, and OGO-6 satellites and the rocket flights 18.117 and 18.118 from Wallops Island on July 12 and 13, 1971. The rocket data provide a day-night pair of vertical profiles that include altitudes not covered by the satellites. Results are presented for Mg + , Al + , Si + and Fe + ions in terms of their detection probabilities, median concentrations and relative abundances with respect to Mg + ions as a function of significant geophysical parameters. Na + and K + ions have been excluded from this study because alkali metal ions driven off the spacecraft hamper the measurement of ambient Na + and K + ions. This study has indicated that in general different metallic ions appear together in comparable concentrations except for Al + , which is an order of magnitude smaller than the others

Ion beam studies. Part 5 - the computer simulation of composite ion implantation profiles

International Nuclear Information System (INIS)

Freeman, J.H.; Booker, D.V.

1977-01-01

The computer simulation of composite ion implantation profiles produced by continuous energy programming and by discrete multiple dose doping is described. It is shown that precise matching of the computed profile to various uniform and power-law distributions can be achieved. (author)

Fatores de risco na gagueira desenvolvimental familial e isolada Risk factors in the familial and sporadic developmental stuttering

Directory of Open Access Journals (Sweden)

Cristiane Moço Canhetti de Oliveira

2011-04-01

Full Text Available OBJETIVO: investigar e comparar os achados dos fatores de risco para a cronicidade da gagueira em crianças com gagueira desenvolvimental familial e isolada. MÉTODOS: participaram 60 crianças de ambos os gêneros, divididas em dois grupos: GI - 30 crianças com gagueira desenvolvimental familial; GII - 30 crianças com gagueira desenvolvimental isolada. A coleta de dados foi realizada por meio do Protocolo de Risco para a Gagueira do Desenvolvimento - PRGD (Andrade, 2006, que considera os seguintes fatores de risco: idade, gênero, tipo de surgimento e tempo de duração das disfluências, tipologia das disfluências, fatores comunicativos e qualitativos associados, histórico mórbido pré, peri e pós natal, fatores estressantes que ocorreram próximo ao surgimento do distúrbio, histórico familial, reação pessoal, familiar e social e atitudes familiares. RESULTADOS: quando o grupo I (GI foi comparado com o grupo II (GII, a única diferença estatisticamente significante foi com relação aos fatores estressantes que ocorreram próximo ao surgimento do distúrbio. CONCLUSÃO: os resultados confirmam a natureza complexa da gagueira, bem como a necessidade de se investigar os vários fatores considerados como de risco para o distúrbio, com intuito de melhorar a compreensão de suas possíveis etiologias.PURPOSE: to investigate and compare the risk factors for stuttering between children with familial developmental stuttering and children with sporadic developmental stuttering. METHODS: 60 children of both genders with stuttering took part, divided in two groups: GI - 30 children with familial developmental stuttering; GII - 30 children with sporadic developmental stuttering. Data were gathered through the Protocol of Risk for the Developmental Stuttering - PRGD (Andrade, 2006, which considers the following factors: age; gender; manner of onset and time of duration for the disfluencies; typology of the disfluencies; associated communicative

Evaluation of structural and optical properties of Ce3+ ions doped (PVA/PVP) composite films for new organic semiconductors

Science.gov (United States)

Ali, F. M.; Kershi, R. M.; Sayed, M. A.; AbouDeif, Y. M.

2018-06-01

Polymer blend films based on Polyvinyl alcohol (PVA)/Poly(vinylpyrrolidone) (PVP) doped with different concentration of cerium ions [(PVA/PVP)-x wt.% Ce3+] (x = 3%, 5%, 10% and 15%) were prepared by the conventional solution casting technique. The characteristics of the prepared polymer composite films were studied using X-ray diffraction (XRD), FT-IR and UV-Vis. spectroscopy. The XRD patterns of the investigated samples revealed a clear reduction on the structural parameters such as crystallinity degree and cluster size D of the doped PVA/PVP blend films compared with the virgin one whereas there is no big difference in the d spacing of the product composite films. Significant changes in FT-IR spectra are observed which reveal an interactions between the cerium ions and PVA/PVP blends. The absorption spectra in the ultraviolet-visible region showed a wide red shift in the fundamental absorption edge of (PVA/PVP)-x wt. % Ce3+ composites. The optical gap Eg gradually decreased from 4.54 eV for the undoped PVA/PVP film to 3.10 eV by increasing Ce3+ ions content. The optical dispersion parameters have been analyzed according to Wemple-Didomenico single oscillator model. The dispersion energy Ed, the single oscillator energy Eo, the average inter-band oscillator wavelength λo and the static refractive index no are strongly affected by cerium ions doping. Cerium ions incorporation in PVA/PVP blend films leads to a significant increase in the refractive index and decrease in the optical gap. These results are likely of great important in varieties of applications including polymer waveguides, organic semiconductors, polymer solar cells and optoelectronics devices.

Pontine hyperperfusion in sporadic hyperekplexia.

Science.gov (United States)

Vetrugno, Roberto; Mascalchi, Mario; Vella, Alessandra; Della Nave, Riccardo; Guerrini, Laura; Vattimo, Angelo; del Giudice, Emanuele Miraglia; Plazzi, Giuseppe; D'Angelo, Roberto; Greco, Giovanni; Montagna, Pasquale

2007-09-01

To explore with neuroimaging techniques the anatomical and functional correlates of sporadic hyperekplexia. Two elderly women with sporadic hyperekplexia underwent neurophysiological assessment, MRI of the brain and proton magnetic resonance spectroscopy (1H-MRS) of the brainstem and frontal lobes. Regional cerebral blood flow was investigated with single photon emission tomography (SPECT) during evoked startles and at rest. Both patients showed excessively large and non-habituating startle responses. In both patients, MRI showed impingement of the brainstem by the vertebrobasilar artery, lack of frontal or brainstem abnormalities on 1H-MRS and hyperperfusion in the dorsal pons and cingulate cortex, and superior frontal gyrus at SPECT during evoked startles. In our patients with hyperekplexia, the vertebrobasilar arteries were found to impinge on the brainstem. Neurophysiological findings and neurofunctional imaging of evoked startles indicated a pontine origin of the movement disorder modulated by activation in cortical, especially frontal, areas. The neurofunctional correlates of evoked startles in human sporadic hyperekplexia are similar to those observed for the startle circuit in animals.

Hypermethylation of the FANCC and FANCL Promoter Regions in Sporadic Acute Leukaemia

Directory of Open Access Journals (Sweden)

C. J. Hess

2008-01-01

Full Text Available Objective: Inactivation of the FA-BRCA pathway results in chromosomal instability. Fanconi anaemia (FA patients have an inherited defect in this pathway and are strongly predisposed to the development of acute myeloid leukaemia (AML. Studies in sporadic cancers have shown promoter methylation of the FANCF gene in a significant proportion of various solid tumours. However, only a single leukaemic case with methylation of one of the FA-BRCA genes has been described to date, i.e. methylation of FANCF in cell line CHRF-288. We investigated the presence of aberrant methylation in 11 FA-BRCA genes in sporadic cases of leukaemia.

Sputtering induced surface composition changes in copper-palladium alloys

International Nuclear Information System (INIS)

Sundararaman, M.; Sharma, S.K.; Kumar, L.; Krishnan, R.

1981-01-01

It has been observed that, in general, surface composition is different from bulk composition in multicomponent materials as a result of ion beam sputtering. This compositional difference arises from factors like preferential sputtering, radiation induced concentration gradients and the knock-in effect. In the present work, changes in the surface composition of copper-palladium alloys, brought about by argon ion sputtering, have been studied using Auger electron spectroscopy. Argon ion energy has been varied from 500 eV to 5 keV. Enrichment of palladium has been observed in the sputter-altered layer. The palladium enrichment at the surface has been found to be higher for 500 eV argon ion sputtering compared with argon ion sputtering at higher energies. Above 500 eV, the surface composition has been observed to remain the same irrespective of the sputter ion energy for each alloy composition. The bulk composition ratio of palladium to copper has been found to be linearly related to the sputter altered surface composition ratio of palladium to copper. These results are discussed on the basis of recent theories of alloy sputtering. (orig.)

Polimorfismo da apolipoproteína e nos familiares em primeiro grau de pacientes com doença de Alzheimer familial ou esporádica Apolipoprotein e polymorphism in first-degree relatives of patients with familial or sporadic Alzheimer's disease

Directory of Open Access Journals (Sweden)

João de Castilho Cação

2007-06-01

Full Text Available INTRODUÇÃO: A apolipoproteína E (apo E é reconhecida como fator de risco para doença de Alzheimer (DA. OBJETIVO: Analisar o polimorfismo da apo E nos familiares em primeiro grau de pacientes com DA familial ou esporádica do tipo tardio, comparando a famílias sem DA. MÉTODO: Foram estudados 40 pacientes com DA familial ou esporádica do tipo tardio, sendo os grupos classificados como provável, segundo critérios da NINCS-ADRDA. RESULTADO: O alelo épsilon3 foi o mais freqüente em todos os grupos. Observou-se freqüência mais elevada de épsilon4 comparando os familiares dos probandos aos do grupo controle (pINTRODUCTION: Apolipoproteín E (apo E has been recognized as a risk factor for Alzheimer disease (AD. OBJECTIVE: To analyze apo E polymorphism in first-degree relatives of patients with familial or sporadic late-onset AD comparing with families without AD. METHOD: Forty patients with familial or sporadic late-onset of AD, being both groups classified as probable, according of NINCS-ADRDA’s criteria. RESULTS: Allele epsilon3 was the most frequent in all of these groups. Higher frequency of epsilon4 when comparing the relatives of the probands with the relatives of the control group (p<0,0001 was observed. Allele epsilon2 showed significant difference only between relatives of familial AD and relatives of control group (p=0,026. CONCLUSION: Apo E polymorphism has not differentiated familial from sporadic AD. The study of families allows to amplify the alelles epsilon2 and epsilon4 representativity, revealing, their value as protecting factor and of risk for AD, respectively.

Enhanced Laser Cooling of Rare-Earth-Ion-Doped Composite Material

International Nuclear Information System (INIS)

You-Hua, Jia; Biao, Zhong; Xian-Ming, Ji; Jian-Ping, Yin

2008-01-01

We predict enhanced laser cooling performance of rare-earth-ions-doped glasses containing nanometre-sized ul-traBne particles, which can be achieved by the enhancement of local Geld around rare earth ions, owing to the surface plasma resonance of small metallic particles. The influence of energy transfer between ions and the particle is theoretically discussed. Depending on the particle size and the ion emission quantum efficiency, the enhancement of the absorption is predicted. It is concluded that the absorption are greatly enhanced in these composite materials, the cooling power is increased as compared to the bulk material

Searching for effects caused by thunderstorms in midlatitude sporadic E layers

Science.gov (United States)

Barta, Veronika; Haldoupis, Christos; Sátori, Gabriella; Buresova, Dalia; Chum, Jaroslav; Pozoga, Mariusz; Berényi, Kitti A.; Bór, József; Popek, Martin; Kis, Árpád; Bencze, Pál

2017-08-01

Possible thunderstorm - sporadic E (Es) layer coupling effects are investigated during two measurement periods, one in 2013 and one in 2014. The analysis was based on ionospheric observations obtained from a Digisonde at Pruhonice, the Czech Republic, an ionosonde at Nagycenk, Hungary, and a 3.59 MHz five-point continuous HF Doppler system located in the western part of the Czech Republic. The latter is capable of detecting ionospheric wave-like variations caused by neutral atmospheric waves generated by thunderstorms. The present study searches for possible impacts on Es layers caused by the presence of two active thunderstorms: one passing across the Czech Republic on June 20, 2013 (19:00-01:00 LT), and one through Hungary on July 30, 2014 (11:00-01:00 LT). During these two time periods, presence and parameters of Es layer were inferred from ionograms, recorded every minute at Pruhonice and every two minutes at Nagycenk, whereas concurrent lightning activity was monitored by the LINET detection network. In addition, transient luminous events (TLEs) were also observed during both nights from Sopron, Hungary and from Nýdek, the Czech Republic. A noticeable fact was the reduction and disappearance of the ongoing Es layer activity during part of the time in both of the traversing thunderstorms. The analysis indicated that the critical frequency foEs dropped below ionosonde detection levels in both cases, possibly because of thunderstorm activity effects. This option, however, needs more case studies in order to be further substantiated.

Mechanical properties and ion release from bioactive restorative composites containing glass fillers and calcium phosphate nano-structured particles.

Science.gov (United States)

Chiari, Marina D S; Rodrigues, Marcela C; Xavier, Tathy A; de Souza, Eugen M N; Arana-Chavez, Victor E; Braga, Roberto R

2015-06-01

To evaluate the effect of the replacement of barium glass by dicalcium phosphate dihydrate (DCPD) particles on the mechanical properties and degree of conversion (DC) of composites. Additionally, calcium and hydrogen phosphate (HPO4(2-)) release were followed for 28 days. Nine composites containing equal parts (in mols) of BisGMA and TEGDMA and 40, 50 or 60 vol% of total filler were manipulated. Filler phase was constituted by silanated barium glass and 0%, 10% or 20% of DCPD particles. DC was determined by near-FTIR. Biaxial flexural strength (BFS) and modulus (E) were tested using the "piston on three balls" method, while fracture toughness (KIc) used the "single edge notched beam" method. Specimens were tested after 24h and 28 days in water. Ion release was determined using inductively coupled plasma optical emission spectrometry (ICP-OES). Data were analyzed by ANOVA/Tukey (DC and ion release) or Kruskal-Wallis/Mann-Whitney (mechanical properties; alpha: 5%). DC was not affected by DCPD. The presence of DCPD reduced BFS for both storage times, while differences in E became evident after 28 days. After 24h, KIc increased with the addition of DCPD; after 28 days, however, KIc decreased only for DCPD-containing composites. Calcium release was similar for both DCPD contents and remained fairly constant during the 28-day period. Overall, HPO4(2-) release was higher at 7 days and did not decrease after 14 days. The composite with the highest filler level and 10% DCPD represented the best compromise between mechanical properties after aging in water and ion release. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Multi-layer structure of mid-latitude sporadic-E observed during the SEEK-2 campaign

Directory of Open Access Journals (Sweden)

T. Ono

2005-10-01

Full Text Available In the mid-latitude ionospheric region, sporadic-E layers (Es layers have often been observed, revealing multiple layers. The Es layers observed during the SEEK-2 rocket campaign showed double electron density peaks; namely, there are stable lower peaks and relatively unstable upper peaks. We examined the effects of wind shear and the electric fields on the generation of the multiple layer structure, in comparison with the electron density profile, the neutral wind, and the DC electric field observed by the S310 rocket experiments. The results showed that the neutral wind shear is mainly responsible for the generation of the lower layer, while the DC electric field makes a significant contribution to the formation of the upper layer. The difference between the lower and upper layers was also explained by the enhanced AC electric field observed at about 103–105 km altitude. The external DC electric field intensity is expected to be ~5 mV/m, which is enough to contribute to generate the Es layers in the ionosphere. Keywords. Ionosphere (Electric fields; Ionospheric irregularities, Mid-latitude ionosphere

High voltage cathode compositions for lithium-ion batteries

Science.gov (United States)

Lu, Zhonghua; Eberman, Kevin W

2017-03-21

A lithium transition metal oxide composition. The composition has the formula Li.sub.a[Li.sub.bNi.sub.cMn.sub.dCo.sub.e]O.sub.2, where a.gtoreq.0.9, b.gtoreq.0, c>0, d>0, e>0, b+c+d+e=1, 1.05.ltoreq.c/d.ltoreq.1.4, 0.05.ltoreq.e.ltoreq.0.30, 0.9.ltoreq.(a+b)/M.ltoreq.1.06, and M=c+d+e. The composition has an O3 type structure.

The Effects of Changing Membrane Compositions and Internal Electrolytes on the Respon of Potassium Ion Sensor

OpenAIRE

Ulianas, Alizar; Heng, Lee Yook

2015-01-01

A study on the changing of membrane compositions and internal solution towards the response potassium ion sensor was carried out. Potassium ion sensor based on photocured cross linking poly(n-butyl acrylate) membranes with varying composition of valinomycin (val), sodium tetrakis [3.5-bis(trifluoro-methyl) phenyl] borat (NaTFPB), types ion of internal solution were investigated. Effects of varying composition of val, NaTFPB, types and concentration of internal solution were observed on potass...

Tuning of wettability of PANI-GNP composites using keV energy ions

Energy Technology Data Exchange (ETDEWEB)

Lakshmi, G.B.V.S., E-mail: lakshmigbvs@gmail.com [Inter University Accelerator Centre, New Delhi 67 (India); Avasthi, D.K. [Amity University, Noida 201313, Uttar Pradesh (India)

2016-07-15

Polyaniline nanofiber composites with various nanomaterials have several applications in electrochemical biosensors. The surface properties of these composites coated electrodes play crucial role in enzyme absorption and analyte detection process. In the present study, Polyaniline-Graphene nanopowder (PANI-GNP) composites were prepared by rapid-mixing polymerization method. The films were prepared on ITO coated glass substrates and irradiated with 42 keV He{sup +} ions produced by indigenously fabricated accelerator at IUAC, New Delhi. The films were characterized before and after irradiation by SEM, Raman spectroscopy and contact angle measurements. The as-prepared films show superhydrophilic nature and after irradiation the films show highly hydrophobic nature with water contact angle (135°). The surface morphology was studied by SEM and structural changes were studied by Raman spectra. The surface morphological modifications induced by keV energy ions helps in tuning the wettability at different ion fluences.

Scanning ion microscopy with low energy lithium ions

International Nuclear Information System (INIS)

Twedt, Kevin A.; Chen, Lei; McClelland, Jabez J.

2014-01-01

Using an ion source based on photoionization of laser-cooled lithium atoms, we have developed a scanning ion microscope with probe sizes of a few tens of nanometers and beam energies from 500 eV to 5 keV. These beam energies are much lower than the typical operating energies of the helium ion microscope or gallium focused ion beam systems. We demonstrate how low energy can be advantageous in ion microscopy when detecting backscattered ions, due to a decreased interaction volume and the potential for surface sensitive composition analysis. As an example application that demonstrates these advantages, we non-destructively image the removal of a thin residual resist layer during plasma etching in a nano-imprint lithography process. - Highlights: • We use an ion source based on photoionization of laser-cooled lithium atoms. • The ion source makes possible a low energy (500 eV to 5 keV) scanning ion microscope. • Low energy is preferred for ion microscopy with backscattered ions. • We use the microscope to image a thin resist used in nano-imprint lithography

Inheritable and sporadic non-autoimmune hyperthyroidism.

Science.gov (United States)

Ferraz, Carolina; Paschke, Ralf

2017-03-01

Hyperthyroidism is a clinical state that results from high thyroid hormone levels which has multiple etiologies, manifestations, and potential therapies. Excluding the autoimmune Graves disease, autonomic adenomas account for the most import cause of non-autoimmune hyperthyroidism. Activating germline mutations of the TSH receptor are rare etiologies for hyperthyroidism. They can be inherited in an autosomal dominant manner (familial or hereditary, FNAH), or may occur sporadically as a de novo condition, also called: persistent sporadic congenital non-autoimmune hyperthyroidism (PSNAH). These three conditions: autonomic adenoma, FNAH and PSNAH constitute the inheritable and sporadic non-autoimmune hyperthyroidism. Particularities in epidemiology, etiology, molecular and clinical aspects of these three entities will be discussed in this review in order to guide to an accurate diagnosis allowing among others genetic counseling and presymptomatic diagnosis for the affected families. The optimal treatment based on the right diagnosis will avoid consequences of a persistent or relapsing hyperthyroidism. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

Development of composite ion exchangers and their use in treatment of liquid radioactive wastes

International Nuclear Information System (INIS)

Sebesta, F.; John, J.; Motl, A.

1997-01-01

Composite inorganic-organic absorbers represent a group of inorganic ion exchangers modified by using binding organic material for preparation of larger size particles having higher granular strength. Such modification of originally powdered or microcrystalline inorganic ion exchangers makes their application in packed beds possible. Modified polyacrylonitrile (PAN) has been used as a universal binding polymer for a number of inorganic ion exchangers. The kinetics of ion exchange and sorption capacity of such composite absorbers is not influenced by the binding polymer mentioned above. The contents of active component in composite absorber can be varied over a very broad range (5-95% of the dry weight of the composite absorber). These composite absorbers have been tested for separation and concentration of various contaminants from aqueous solutions. Their high selectivity and sorption efficiency are advantageous for treatment of various radioactive and/or industrial waste waters, removal of natural and/or artificial radionuclides and heavy or toxic metals from underground water, determination of radionuclides ( 137 Cs, 60 Co, U, Ra) in the environment, etc. Examples of some of these applications are presented in this report. (author). 21 refs, 9 figs, 10 tabs

Composition: S.C.E

DEFF Research Database (Denmark)

2012-01-01

S.C.E. is a large collection of open compositions to be realised by improvising musicians. See more about my composition practise in the entry "Composition - General Introduction". This work is licensed under a Creative Commons "by-nc" License. You may for non-commercial purposes use and distribute...

Renewable and superior thermal-resistant cellulose-based composite nonwoven as lithium-ion battery separator.

Science.gov (United States)

Zhang, Jianjun; Liu, Zhihong; Kong, Qingshan; Zhang, Chuanjian; Pang, Shuping; Yue, Liping; Wang, Xuejiang; Yao, Jianhua; Cui, Guanglei

2013-01-01

A renewable and superior thermal-resistant cellulose-based composite nonwoven was explored as lithium-ion battery separator via an electrospinning technique followed by a dip-coating process. It was demonstrated that such nanofibrous composite nonwoven possessed good electrolyte wettability, excellent heat tolerance, and high ionic conductivity. The cells using the composite separator displayed better rate capability and enhanced capacity retention, when compared to those of commercialized polypropylene separator under the same conditions. These fascinating characteristics would endow this renewable composite nonwoven a promising separator for high-power lithium-ion battery.

Adsorption behaviour and kinetics of exchange of Zn2+ and Eu3+ ions on a composite ion exchanger

International Nuclear Information System (INIS)

Morcos, T.N.

2007-01-01

Equilibria and kinetics of exchange of both Zn2+ and Eu3+ ions on a composite ion-exchanger, cobalt hexacyanocobaltate (III) (CoHCC) incorporated in polyacrylonitrile (PAN), has been studied. The apparent capacity of CoHCC-PAN for Zn2+ and Eu3+ was determined and found to be 0.353 and 0.69 meq/g, respectively. The higher capacity for Eu3+ ions than that for Zn2+ ions is due to the higher electrostatic interaction strength of the higher charge ion with the surface. Freundlich and Langmiur adsorption isotherms were used to investigate solute (Zn2+ or Eu3+) exchange phenomenon at the liquid/solid interface. The results indicated that both Langmuir and Freundlich isotherms fit well for both Zn2+ and Eu3+. Sorption data have been also treated with the Dubinin-Radushkevich equation. The kinetics of Zn2+ or Eu3+ sorption on the composite seems to show that the reaction was proceed via two steps. The first one was fast and probably due to adsorption followed by a slow exchange reaction. In view of the data obtained on the effect of particle size and metal ion concentrations on the rate of exchange reaction, it is concluded that the mechanism for both ions was chemical control. Generally, it seems that there are two exchange sites chemically equivalent but present in pores of different sizes which lead to different degrees of dehydration of the ions sorbed on the two sites

Complementary scattered and recoiled ion data from TOF-E heavy ion elastic recoil detection analysis

International Nuclear Information System (INIS)

Johnston, P.N.; El Bouanani, M.; Stannard, W.B.; Bubb, I.F.; Cohen, D.D.; Dytlewski, N.; Siegele, R.

1998-01-01

The advantage of Time of Flight and Energy (ToF-E) Heavy Ion Elastic Recoil Detection Analysis (HIERDA) over Rutherford Backscattering (RBS) analysis is its mass and energy dispersive capabilities. The mass resolution of ToF-E HIERDA deteriorates for very heavy elements. The limitation is related to the poor energy resolution of Si detectors for heavy ions. While the energy spectra from ToF-E HIERDA data are normally used to extract depth profiles, this work discusses the benefits of using the time spectra of both the recoiled and the scattered ions for depth profiling. The simulation of the complementary scattered and recoiled ion time spectra improves depth profiling and reduced current limitations when dealing with very heavy ions, such as Pt, Bi, Ta. (authors)

The e+, e- background at Relativistic Heavy Ion Collider (RHIC) generated by beam crossing

International Nuclear Information System (INIS)

Rhoades-Brown, M.J.; Ludlam, T.; Wu, J.; Bottcher, C.; Strayer, M.

1990-01-01

At the Brookhaven Relativistic Heavy Ion Collider (RHIC), fully stripped heavy ions will circulate in each of two rings up to beam energies of 250 (Z/A) GeV/u. During the beam crossing, the peripheral electromagnetic interaction between the heavy ions is sufficient to induce copious production of di-lepton pairs. These pairs are a potential source of background for the detectors at RHIC. In this paper we discuss the expected number of e + ,e - pairs, given the accepted initial luminosity value L of the collider. More importantly, we also calculate the differential cross sections for the angle, energy, rapidity and momentum distribution of the leptons. Using the luminosity L of the collider, these differential cross sections are normalized to the expected number of leptons per second. We restrict ourselves to e + ,e - production, a discussion of μ + ,μ - and τ + τ - distributions will be published later. The results are presented for the expected worst case, namely 197 Au 79+ ions at a beam kinetic energy of 100 GeV/u. This is forseen to be the heaviest ion for high luminosity experiments at RHIC. We note for a given energy, the cross section for e + ,e - production scales as Z 4 , where Z is the atomic number of the ions

A spectral study of the mid-latitude sporadic E layer characteristic oscillations comparable to those of the tidal and the planetary waves

Science.gov (United States)

Pignalberi, A.; Pezzopane, M.; Zuccheretti, E.

2015-01-01

In this paper different spectral analyses are employed to investigate the tidal and planetary wave periodicities imprinted in the following two main characteristics of the sporadic E (Es) layer: the top frequency (ftEs) and the lowest virtual height (h‧Es). The study is based on ionograms recorded during the summertime of 2013, and precisely in June, July, August and September, by the Advanced Ionospheric Sounder by Istituto Nazionale di Geofisica e Vulcanologia (AIS-INGV) ionosondes installed at Rome (41.8°N, 12.5°E) and Gibilmanna (37.9°N, 14.0°E), Italy. It was confirmed that the diurnal and semidiurnal atmospheric tides play a fundamental role in the formation of the mid-latitude Es layers, acting through their vertical wind-shear forcing of the long-living metallic ions in the lower thermosphere, and at the same time it was found that the planetary atmospheric waves might affect the Es layers acting through their horizontal wind-shear forcing with periods close to the normal Rossby modes, that is 2, 5, 10 and 16 days. The wavelet analysis shows also that the ftEs and h‧Es tidal oscillations undergo a strong amplitude modulation with periods of several days and with important differences between the two parameters. This amplitude modulation, characterizing markedly the first thirty days of the ftEs spectrogram, suggests that Es layers are affected indirectly by planetary waves through their nonlinear interaction with the atmospheric tides at lower altitudes. This study wants to be a continuation of the Haldoupis et al. (2004) work in order to verify their results for the foEs characteristic and on the other hand to extend the study also to the h‧Es characteristic not yet shown so far. Anyhow, the study confirms that ionosonde data, especially those registered in summertime, represent a powerful tool for studying tidal and planetary waves properties and their climatology in the mesosphere-low-thermosphere region.

MnO-carbon hybrid nanofiber composites as superior anode materials for lithium-ion batteries

International Nuclear Information System (INIS)

Wang, Jian-Gan; Yang, Ying; Huang, Zheng-Hong; Kang, Feiyu

2015-01-01

MnO-carbon hybrid nanofiber composites are fabricated by electrospinning polyimide/manganese acetylacetonate precursor and a subsequent carbonization process. The composition, phase structure and morphology of the composites are characterized by scanning and transmission electron microscopy, X-ray diffraction and thermogravimetric analysis. The results indicate that the composites exhibit good nanofibrous morphology with MnO nanoparticles uniformly encapsulated by carbon nanofibers. The hybrid nanofiber composites are used directly as freestanding anodes for lithium-ion batteries to evaluate their electrochemical properties. It is found that the optimized MnO-carbon nanofiber composite can deliver a high reversible capacity of 663 mAh g −1 , along with excellent cycling stability and good rate capability. The superior performance enables the composites to be promising candidates as an anode alternative for high-performance lithium-ion batteries

Heavy ion composition in the inner heliosphere: Predictions for Solar Orbiter

Science.gov (United States)

Lepri, S. T.; Livi, S. A.; Galvin, A. B.; Kistler, L. M.; Raines, J. M.; Allegrini, F.; Collier, M. R.; Zurbuchen, T.

2014-12-01

The Heavy Ion Sensor (HIS) on SO, with its high time resolution, will provide the first ever solar wind and surpathermal heavy ion composition and 3D velocity distribution function measurements inside the orbit of Mercury. These measurements will provide us the most in depth examination of the origin, structure and evolution of the solar wind. The near co-rotation phases of the orbiter will enable the most accurate mapping of in-situ structures back to their solar sources. Measurements of solar wind composition and heavy ion kinetic properties enable characterization of the sources, transport mechanisms and acceleration processes of the solar wind. This presentation will focus on the current state of in-situ studies of heavy ions in the solar wind and their implications for the sources of the solar wind, the nature of structure and variability in the solar wind, and the acceleration of particles. Additionally, we will also discuss opportunities for coordinated measurements across the payloads of Solar Orbiter and Solar Probe in order to answer key outstanding science questions of central interest to the Solar and Heliophysics communities.

First-Principles Study of MoO3/Graphene Composite as Cathode Material for High-Performance Lithium-Ion Batteries

Science.gov (United States)

Cui, Yanhua; Zhao, Yu; Chen, Hong; Wei, Kaiyuan; Ni, Shuang; Cui, Yixiu; Shi, Siqi

2018-03-01

Using first-principles calculations, we have systematically investigated the adsorption and diffusion behavior of Li in MoO3 bulk, on MoO3 (010) surface and in MoO3/graphene composite. Our results indicate that, in case of MoO3 bulk, Li diffusion barriers in the interlayer and intralayer spaces are 0.55 eV and 0.58 eV respectively, which are too high to warrant fast Lithium-ion charge/discharge processes. While on MoO3 (010) surface, Li exhibits a diffusion barrier as low as 0.07 eV which guarantees an extremely fast Li diffusion rate during charge/discharge cycling. However, in MoO3/graphene monolayer, Li diffusion barrier is at the same level as that on MoO3 (010) surface, which also ensures a very rapid Li charge/discharge rate. The rapid Li charge/discharge rate in this system originates from the removal of the upper dangling O1 atoms which hinder the Li diffusion on the lower MoO3 layer. Besides this, due to the interaction between Li and graphene, the Li average binding energy increases to 0.14 eV compared to its value on MoO3 (010) surface which contributes to a higher voltage. Additionally, the increased ratio of surface area provides more space for Li storage and the capacity of MoO3/graphene composite increases up to 279.2 mAhg-1. The last but not the least, due to the high conductivity of graphene, the conductivity of MoO3/graphene composite enhances greatly which is beneficial for electrode materials. In the light of present results, MoO3/graphene composite exhibits higher voltage, good conductivity, large Li capacity and very rapid Li charge/discharge rate, which prove it as a promising cathode material for high-performance lithium-ion batteries (LIBs).

Alumina/Phenolphthalein Polyetherketone Ceramic Composite Polypropylene Separator Film for Lithium Ion Power Batteries

International Nuclear Information System (INIS)

Wang, Jing; Hu, Zhiyu; Yin, Xiunan; Li, Yunchao; Huo, Hong; Zhou, Jianjun; Li, Lin

2015-01-01

Highlights: • PEK-C (T g : ∼230 °C) was used as binder to prepare ceramic coated composite PP separator. • The composite PP separator was stable and showed low thermal shrinkage in the electrolyte solvent. • The composite PP separator was helpful for high current density discharge. • The composite PP separator improved the safety performance of the coin cells. - Abstract: One way to obtain the lithium ion power battery with better safety performance was to increase the thermal shrinkage resistance of the separator at higher temperature. Phenolphthalein polyetherketone (PEK-C) is a polymer that can withstand high temperature to about 230 °C. Here, we developed a new Al 2 O 3 coated composite polypropylene (PP) separator with PEK-C as binder. The coating layer was formed on the surface of the PP separator and both ceramic particles and binder did not infiltrated into the separator along the thickness direction. The composite separator with 4 μm coating layer provided balanced permeability and thermal shrinkage properties. The composite separator was stable at the electrochemical window for lithium ion battery. The coin cells with composite separator showed better charge/discharge performance than that of the cells with the PP separator. It seemed that the composite separator was helpful for high current density discharge. Also, the battery safety performance test had verified that the Al 2 O 3 coated composite separator with PEK-C as binder had truly improved the safety performance of the coin cells. So, the newly developed Al 2 O 3 coated composite PP separator was a promising safety product for lithium ion power batteries with high energy density

Remote sensing of electron density and ion composition using nonducted whistler observations on OGO 1 and Van Allen Probes

Science.gov (United States)

Sonwalkar, V. S.; Butler, J.; Reddy, A.

2017-12-01

We present a new method to remotely measure magnetospheric electron density and ion composition using lightning generated nonducted whistlers observed on a satellite. Electron and ion densities play important roles in magnetospheric processes such as wave-particle interactions in the equatorial region and ion-neutral dynamics in the ionosphere, and are important for calculating space weather effects such as particle precipitation, GPS scintillations, and satellite drag. The nonducted whistler resulting from a single lightning appears on a spectrogram as a series of magnetospherically reflected traces with characteristic dispersion (time delay versus frequency) and upper and lower cut off frequencies. Ray tracing simulations show that these observed characteristics depend on the magnetospheric electron density and ion composition. The cut off frequencies depend on both electron density and ion composition. The dispersion depends strongly on electron density, but weakly on ion composition. Using an iterative process to fit the measured dispersion and cutoff frequencies to those obtained from ray tracing simulations, it is possible to construct the electron and ion density profiles of the magnetosphere. We demonstrate our method by applying it to nonducted whistlers observed on OGO 1 and Van Allen probe satellites. In one instance (08 Nov 1965), whistler traces observed on OGO 1 (L = 2.4, λm = -6°) displayed a few seconds of dispersion and cutoff frequencies in the 1-10 kHz range. Ray tracing analysis showed that a diffusive equilibrium density model with the following parameters can reproduce the observed characteristics of the whistler traces: 1900 el/cc at L=2.4 and the equator, 358,000 el/cc at F2 peak (hmF2 = 220 km), the relative ion concentrations αH+ = 0.2, αHe+ = 0.2, and αO+ = 0.6 at 1000 km, and temperature 1600 K. The method developed here can be applied to whistlers observed on the past, current, and future magnetospheric satellite missions carrying

The composition of heavy ions in solar energetic particle events

International Nuclear Information System (INIS)

Fan, C.Y.

1984-01-01

The composition within individual SEP events may vary both with time and energy, and will in general be different from that in other SEP events. Average values of relative abundances measured in a large number of SEP events, however, are found to be roughly energy independent in the proportional1 to proportional20 MeV per nucleon range, and show a systematic deviation from photospheric abundances which seems to be organized in terms of the first ionization potential of the ion. Direct measurements of the charge states of SEPs have revealed the surprisingly common presence of energetic He + along with heavy ions with typically coronal ionization states. High-resolution measurements of isotopic abundance ratios in a small number of SEP events show these to be consistent with the universal composition except for the puzzling overabundance of the SEP 22 Ne/ 20 Ne relative to this isotopes ratio in the solar wind. The broad spectrum of observed elemental abundance variations, which in their extreme result in composition anomalies characteristic of 3 He-rich, heavy-ion rich and carbon-poor SEP events, along with direct measurements of the ionization states of SEPs provide essential information on the physical characteristics of, and conditions in the source regions, as well as important constraints to possible models for SEP production. (orig./HM)

Phase selection controlled by sodium ions in the synthesis of FAU/LTA composite zeolite

Directory of Open Access Journals (Sweden)

Linyan Hu, Sujuan Xie, Qingxia Wang, Shenglin Liu and Longya Xu

2009-01-01

Full Text Available Zeolite faujasite (FAU, Linde type A (LTA and FAU/LTA composite have been synthesized using tetramethylammonium cation (TMA + as template, by adjusting only the concentration of Na + ions in the initial solution (1.00 Al2 O3 4.36 SiO2 : 2.39 (TMA2 O : β Na2 O : 249.00H2 O. Na + ions alter the phase composition of the product more than TMA+ or OH− ions. When Na2 O concentration [Na2 O] increases from 0.024 to 0.168, the product gradually changes from pure FAU to pure LTA via the formation of FAU/LTA composite with increasing LTA fraction. Interestingly, the induction periods of FAU and LTA in the FAU/LTA composite zeolite ([Na2 O] is 0.072 are both 13 h, quite different from the induction periods of their individual pure phases—45 h for FAU and 4 h for LTA. During the crystallization, the LTA/(FAU + LTA fraction in the composite zeolite decreases in a nearly linear fashion. Scanning electron microscopy, thermogravimetry and differential thermal analysis indicate some difference between the properties of the FAU/LTA composite zeolite and of the mechanical mixture.

A high-resolution mass spectrometer to measure atmospheric ion composition

Directory of Open Access Journals (Sweden)

H. Junninen

2010-08-01

Full Text Available In this paper we present recent achievements on developing and testing a tool to detect the composition of ambient ions in the mass/charge range up to 2000 Th. The instrument is an Atmospheric Pressure Interface Time-of-Flight Mass Spectrometer (APi-TOF, Tofwerk AG. Its mass accuracy is better than 0.002%, and the mass resolving power is 3000 Th/Th. In the data analysis, a new efficient Matlab based set of programs (tofTools were developed, tested and used. The APi-TOF was tested both in laboratory conditions and applied to outdoor air sampling in Helsinki at the SMEAR III station. Transmission efficiency calibrations showed a throughput of 0.1–0.5% in the range 100–1300 Th for positive ions, and linearity over 3 orders of magnitude in concentration was determined. In the laboratory tests the APi-TOF detected sulphuric acid-ammonia clusters in high concentration from a nebulised sample illustrating the potential of the instrument in revealing the role of sulphuric acid clusters in atmospheric new particle formation. The APi-TOF features a high enough accuracy, resolution and sensitivity for the determination of the composition of atmospheric small ions although the total concentration of those ions is typically only 400–2000 cm⁻³. The atmospheric ions were identified based on their exact masses, utilizing Kendrick analysis and correlograms as well as narrowing down the potential candidates based on their proton affinities as well isotopic patterns. In Helsinki during day-time the main negative ambient small ions were inorganic acids and their clusters. The positive ions were more complex, the main compounds were (polyalkyl pyridines and – amines. The APi-TOF provides a near universal interface for atmospheric pressure sampling, and this key feature will be utilized in future laboratory and field studies.

Synthesis, characterization and nitrite ion sensing performance of reclaimable composite samples through a core-shell structure

Science.gov (United States)

Cui, Xiao; Yuqing, Zhao; Cui, Jiantao; Zheng, Qian; Bo, Wang

2018-02-01

The following paper reported and discussed a nitrite ion optical sensing platform based on a core-shell structure, using superamagnetic nanoparticles as the core, a silica molecular sieve MCM-41 as the shell and two rhodamine derivatives as probe, respectively. This superamagnetic core made this sensing platform reclaimable after finishing nitrite ion sensing procedure. This sensing platform was carefully characterized by means of electron microscopy images, porous structure analysis, magnetic response, IR spectra and thermal stability analysis. Detailed analysis suggested that the emission of these composite samples was quenchable by nitrite ion, showing emission turn off effect. A static sensing mechanism based on an additive reaction between chemosensors and nitrite ion was proposed. These composite samples followed Demas quenching equation against different nitrite ion concentrations. Limit of detection value was obtained as low as 0.4 μM. It was found that, after being quenched by nitrite ion, these composite samples could be reclaimed and recovered by sulphamic acid, confirming their recyclability.

Boron oxide–tin oxide/graphene composite as anode materials for lithium ion batteries

International Nuclear Information System (INIS)

Wen, Lina; Qin, Xue; Meng, Wei; Cao, Ning; Song, Zhonghai

2016-01-01

Highlights: • B_2O_3–SnO_2/G anode material is prepared by chemical heat solvent method for LIBs. • B_2O_3–SnO_2/G shows much improved cycling performance and rate capability. • B_2O_3 plays an important role in improving the performance. - Abstract: B_2O_3–SnO_2/graphene (B_2O_3–SnO_2/G) composite is fabricated via a chemical heat solvent method and utilized as anode material for lithium ion batteries. The added B_2O_3 dramatically improves the electrochemical performance of lithium ion batteries compared to the SnO_2/G composite. The B_2O_3–SnO_2/G composites as anode show an outstanding discharge capacity of 1404.9 mAh g"−"1 at 500 mA g"−"1 after 200 cycles and an excellent rate capacity, which apparently outperforms the previously reported SnO_2-based anode material. These improved electrochemical performance characteristics are due to the B_2O_3 played a buffering role, which are easily beneficial for accommodating the volume change during the lithium ions insertion/extraction processes. Furthermore, boron atoms can accept electrons for its electron-deficient nature and boron ions could release electrons, which lead to electrons' increased density and conductivity are increased. The results indicate that the B_2O_3–SnO_2/G composite is a promising anode material for lithium ion batteries.

Selenofuranoside Ameliorates Memory Loss in Alzheimer-Like Sporadic Dementia: AChE Activity, Oxidative Stress, and Inflammation Involvement

Directory of Open Access Journals (Sweden)

Cristiano Chiapinotto Spiazzi

2015-01-01

Full Text Available Alzheimer’s disease (AD is becoming more common due to the increase in life expectancy. This study evaluated the effect of selenofuranoside (Se in an Alzheimer-like sporadic dementia animal model. Male mice were divided into 4 groups: control, Aβ, Se, and Aβ + Se. Single administration of Aβ peptide (fragments 25–35; 3 nmol/3 μL or distilled water was administered via intracerebroventricular (i.c.v. injection. Selenofuranoside (5 mg/kg or vehicle (canola oil was administered orally 30 min before Aβ and for 7 subsequent days. Memory was tested through the Morris water maze (MWM and step-down passive-avoidance (SDPA tests. Antioxidant defenses along with reactive species (RS were assessed. Inflammatory cytokines levels and AChE activity were measured. SOD activity was inhibited in the Aβ group whereas RS were increased. AChE activity, GSH, and IL-6 levels were increased in the Aβ group. These changes were reflected in impaired cognition and memory loss, observed in both behavioral tests. Se compound was able to protect against memory loss in mice in both behavioral tests. SOD and AChE activities as well as RS and IL-6 levels were also protected by Se administration. Therefore, Se is promising for further studies.

Preparation of Advanced CuO Nanowires/Functionalized Graphene Composite Anode Material for Lithium Ion Batteries

Directory of Open Access Journals (Sweden)

Jin Zhang

2017-01-01

Full Text Available The copper oxide (CuO nanowires/functionalized graphene (f-graphene composite material was successfully composed by a one-pot synthesis method. The f-graphene synthesized through the Birch reduction chemistry method was modified with functional group “–(CH25COOH”, and the CuO nanowires (NWs were well dispersed in the f-graphene sheets. When used as anode materials in lithium-ion batteries, the composite exhibited good cyclic stability and decent specific capacity of 677 mA·h·g−1 after 50 cycles. CuO NWs can enhance the lithium-ion storage of the composites while the f-graphene effectively resists the volume expansion of the CuO NWs during the galvanostatic charge/discharge cyclic process, and provide a conductive paths for charge transportation. The good electrochemical performance of the synthesized CuO/f-graphene composite suggests great potential of the composite materials for lithium-ion batteries anodes.

Magnetic composite beads for sorption of cesium ions from aqueous streams

International Nuclear Information System (INIS)

Shinde, Rakesh N.; Pandey, A.K.; Acharya, R.; Rajurkar, N.S.

2014-01-01

Magnetic separation of metal ions is one of the promising methods due to simple, fast, efficient and cost effective technology. Highly selective magnetic sorbents can be designed by immobilizing functional groups in magnetic carrier which binds to the target specific ions. In the present work chitosan-(3-aminopropyl) triethoxysilane (APTS)- copperferrocyanide (CFC) composite beads have been synthesized for sorption of 137 Cs ions from aqueous streams. Physical characterization of the best resulted polymer beads was carried out by SEM-EDX and VSM technique. Sorption of Cs ions in the various magnetic polymer beads were studied in different aqueous condition by 137 Cs (662 KeV) radiotracer assay

Nanoporous titanium niobium oxide and titanium tantalum oxide compositions and their use in anodes of lithium ion batteries

Science.gov (United States)

Dai, Sheng; Guo, Bingkun; Sun, Xiao-Guang; Qiao, Zhenan

2017-10-31

Nanoporous metal oxide framework compositions useful as anodic materials in a lithium ion battery, the composition comprising metal oxide nanocrystals interconnected in a nanoporous framework and having interconnected channels, wherein the metal in said metal oxide comprises titanium and at least one metal selected from niobium and tantalum, e.g., TiNb.sub.2-x Ta.sub.xO.sub.y (wherein x is a value from 0 to 2, and y is a value from 7 to 10) and Ti.sub.2Nb.sub.10-vTa.sub.vO.sub.w (wherein v is a value from 0 to 2, and w is a value from 27 to 29). A novel sol gel method is also described in which sol gel reactive precursors are combined with a templating agent under sol gel reaction conditions to produce a hybrid precursor, and the precursor calcined to form the anodic composition. The invention is also directed to lithium ion batteries in which the nanoporous framework material is incorporated in an anode of the battery.

Sporadic wind wave horse-shoe patterns

Directory of Open Access Journals (Sweden)

S. Yu. Annenkov

1999-01-01

Full Text Available The work considers three-dimensional crescent-shaped patterns often seen on water surface in natural basins and observed in wave tank experiments. The most common of these 'horse-shoe-like' patterns appear to be sporadic, i.e., emerging and disappearing spontaneously even under steady wind conditions. The paper suggests a qualitative model of these structures aimed at explaining their sporadic nature, physical mechanisms of their selection and their specific asymmetric form. First, the phenomenon of sporadic horse-shoe patterns is studied numerically using the novel algorithm of water waves simulation recently developed by the authors (Annenkov and Shrira, 1999. The simulations show that a steep gravity wave embedded into widespectrum primordial noise and subjected to small nonconservative effects typically follows the simple evolution scenario: most of the time the system can be considered as consisting of a basic wave and a single pair of oblique satellites, although the choice of this pair tends to be different at different instants. Despite the effective low-dimensionality of the multimodal system dynamics at relatively sho ' rt time spans, the role of small satellites is important: in particular, they enlarge the maxima of the developed satellites. The presence of Benjamin-Feir satellites appears to be of no qualitative importance at the timescales under consideration. The selection mechanism has been linked to the quartic resonant interactions among the oblique satellites lying in the domain of five-wave (McLean's class II instability of the basic wave: the satellites tend to push each other out of the resonance zone due to the frequency shifts caused by the quartic interactions. Since the instability domain is narrow (of order of cube of the basic wave steepness, eventually in a generic situation only a single pair survives and attains considerable amplitude. The specific front asymmetry is found to result from the interplay of quartic

Carbon nanotube/carbon nanotube composite AFM probes prepared using ion flux molding

Science.gov (United States)

Chesmore, Grace; Roque, Carrollyn; Barber, Richard

The performance of carbon nanotube-carbon nanotube composite (CNT/CNT composite) atomic force microscopy (AFM) probes is compared to that of conventional Si probes in AFM tapping mode. The ion flux molding (IFM) process, aiming an ion beam at the CNT probe, aligns the tip to a desired angle. The result is a relatively rigid tip that is oriented to offset the cantilever angle. Scans using these probes reveal an improvement in image accuracy over conventional tips, while allowing higher aspect ratio imaging of 3D surface features. Furthermore, the lifetimes of CNT-CNT composite tips are observed to be longer than both conventional tips and those claimed for other CNT technologies. Novel applications include the imaging of embiid silk. Supported by the Clare Boothe Luce Research Scholars Award and Carbon Design Innovations.

A polymeric membrane ion selective electrode based on organic-inorganic composite ion exchanger for the determination of thorium(IV)

International Nuclear Information System (INIS)

Chandra, Sulekh; Agarwal, Himanshu; Chandan Kumar, Singh; Sindhu, Susheel Kumar; Pankaj Kumar

2005-01-01

A poly(vinyl chloride) membrane electrode based on organic- inorganic composite ion exchanger, tin(IV) tungstoselenate-pyridine, has been prepared and tested for the selective determination of thorium(IV) ions. The PVC membrane electrode comprising 16% composite ion exchanger as the electroactive phase, 50% o-dioctyl phthalate as plasticizer, 4% tetraphenyl borate as anionic excluder and 30% poly(vinylchloride) displays a linear response to thorium(IV) ions over a wide concentration range of 1.0 x 10 -1 -8.0 x 10 -6 M with a Nernstain slope of 14.2 mV/ decade. The electrode shows a very short response time (∼15 s) and may be used in the pH range 2.5-9.0. The selectivity coefficient for alkali, alkaline earth and transition is smaller than 4.0 x 10 -4 . The sensor has been successfully used as an indicator electrode in the potentiometric titration of Th 4+ with EDTA as well as also for the determination of Th 4+ in the binary mixtures. (author)

Integrated ion imprinted polymers-paper composites for selective and sensitive detection of Cd(II) ions

Energy Technology Data Exchange (ETDEWEB)

Huang, Kai [State Key Laboratory of Environment Health - Incubation, Key Laboratory of Environment and Health, Ministry of Education, Key Laboratory of Environment and Health Wuhan, Ministry of Environmental Protection, School of Public Health, Tongji Medical College, Huazhong University of Science and Technology, #13 Hangkong Road, Hubei, 430030, Wuhan (China); Chen, Ying [Hubei Center for Disease Control and Prevention, No. 6 ZhuoDao Quan North Road, 430079, Wuhan (China); Zhou, Feng [State Key Laboratory of Environment Health - Incubation, Key Laboratory of Environment and Health, Ministry of Education, Key Laboratory of Environment and Health Wuhan, Ministry of Environmental Protection, School of Public Health, Tongji Medical College, Huazhong University of Science and Technology, #13 Hangkong Road, Hubei, 430030, Wuhan (China); Zhao, Xiaoya [Hubei Entry-Exit Inspection and Quarantine Bureau of PRC, No.588 Qingtaidadao Road, Hubei, 430022, Wuhan (China); Liu, Jiafa [Hubei Center for Disease Control and Prevention, No. 6 ZhuoDao Quan North Road, 430079, Wuhan (China); Mei, Surong; Zhou, Yikai [State Key Laboratory of Environment Health - Incubation, Key Laboratory of Environment and Health, Ministry of Education, Key Laboratory of Environment and Health Wuhan, Ministry of Environmental Protection, School of Public Health, Tongji Medical College, Huazhong University of Science and Technology, #13 Hangkong Road, Hubei, 430030, Wuhan (China); Jing, Tao, E-mail: jingtao@hust.edu.cn [State Key Laboratory of Environment Health - Incubation, Key Laboratory of Environment and Health, Ministry of Education, Key Laboratory of Environment and Health Wuhan, Ministry of Environmental Protection, School of Public Health, Tongji Medical College, Huazhong University of Science and Technology, #13 Hangkong Road, Hubei, 430030, Wuhan (China)

2017-07-05

Highlights: • IIPs are first grafted on the low-cost A4 print paper to develop an integrated paper-based device. • As an imprinted composite, the adsorption capacity is 155.2 mg g{sup –1} and the imprinted factor is more than 3.0. • As an analytical method, the limit of detection is 0.4 ng mL{sup –1}. • Based on the water quality standards, it could be used to determine Cd(II) ions in drinking water. - Abstract: Paper-based sensor is a new alternative technology to develop a portable, low-cost, and rapid analysis system in environmental chemistry. In this study, ion imprinted polymers (IIPs) using cadmium ions as the template were directly grafted on the surface of low-cost print paper based on the reversible addition-fragmentation chain transfer polymerization. It can be applied as a recognition element to selectively capture the target ions in the complex samples. The maximum adsorption capacity of IIPs composites was 155.2 mg g{sup –1} and the imprinted factor was more than 3.0. Then, IIPs-paper platform could be also applied as a detection element for highly selective and sensitive detection of Cd(II) ions without complex sample pretreatment and expensive instrument, due to the selective recognition, formation of dithizone-cadmium complexes and light transmission ability. Under the optimized condition, the linear range was changed from 1 to 100 ng mL{sup –1} and the limit of detection was 0.4 ng mL{sup –1}. The results were in good agreement with the classic ICP-MS method. Furthermore, the proposed method can also be developed for detection of other heavy metals by designing of new IIPs.

Effect of ion composition on oblique magnetosonic waves

International Nuclear Information System (INIS)

Kondo, Yuichi; Toida, Mieko

2011-01-01

The effects of ion composition on oblique magnetosonic waves in a two-ion-species plasma are studied theoretically and numerically. First, it is analytically shown that the KdV equation for the low-frequency mode, the lower branch of magnetosonic waves, is valid for amplitudes ε max (l-) , where ε max (l-) is a measure of the upper limit of the amplitude of the rarefactive solitary pulse of the low-frequency mode and is given as a function of the propagation angle of the wave θ, the density ratio and cyclotron frequency ratio of two ion species. The value of ε max (l-) increases with decreasing θ. Next, with electromagnetic particle simulations, the nonlinear evolution of the low- and high-frequency modes is examined. It is demonstrated that shorter-wavelength low- and high-frequency-mode waves are generated from a long-wavelength low-frequency-mode pulse if its amplitude ε exceeds ε max (l-) . (author)

Serum uric acid and lipid profiles in sporadic Creutzfeldt-Jakob disease.

Science.gov (United States)

Chen, Shuai; He, Shuang; Shang, Jun-Kui; Ma, Ming-Ming; Xu, Chang-Shui; Shi, Xiao-Hong; Zhang, Jie-Wen

2016-02-01

Creutzfeldt-Jakob disease (CJD) is a rare, rapidly progressive, and fatal neurodegenerative disease affecting the central nervous system. Brain lipid homeostasis and oxidative stress seem to play an important role in the disease pathogenesis. But little was known whether serum lipids and uric acid (a natural antioxidant) levels changed in patients with prion disease. Here we retrospectively reviewed and compared the serum lipids and uric acid levels of 19 probable sporadic CJD patients and 26 healthy control subjects. We found that the serum uric acid levels in sporadic CJD patients were significantly lower than that in controls (P=0.01). Serum triglycerides, cholesterol, low-density lipoprotein (LDL), high-density lipoprotein (HDL), and apolipoprotein A1 (ApoA1) were similar in sporadic CJD patients and controls. However, LDL/HDL ratio was lower in sporadic CJD patients (P=0.003). The low serum uric acid and LDL/HDL ratio levels in sporadic CJD indicate that dysfunction in the lipid homeostasis and oxidative stress is associated with sporadic prion disease. Copyright © 2015 The Canadian Society of Clinical Chemists. Published by Elsevier Inc. All rights reserved.

Boron oxide–tin oxide/graphene composite as anode materials for lithium ion batteries

Energy Technology Data Exchange (ETDEWEB)

Wen, Lina [Department of chemistry, School of Science, Tianjin University, and Collaborative Innovation Center of Chemical Science and Engineering (Tianjin), Tianjin 300072 (China); Qin, Xue, E-mail: qinxue@tju.edu.cn [Department of chemistry, School of Science, Tianjin University, and Collaborative Innovation Center of Chemical Science and Engineering (Tianjin), Tianjin 300072 (China); Key Laboratory of Advanced Energy Materials Chemistry (Ministry of Education), College of Chemistry, Nankai University, Tianjin 300071 (China); Meng, Wei; Cao, Ning; Song, Zhonghai [Department of chemistry, School of Science, Tianjin University, and Collaborative Innovation Center of Chemical Science and Engineering (Tianjin), Tianjin 300072 (China)

2016-11-15

Highlights: • B{sub 2}O{sub 3}–SnO{sub 2}/G anode material is prepared by chemical heat solvent method for LIBs. • B{sub 2}O{sub 3}–SnO{sub 2}/G shows much improved cycling performance and rate capability. • B{sub 2}O{sub 3} plays an important role in improving the performance. - Abstract: B{sub 2}O{sub 3}–SnO{sub 2}/graphene (B{sub 2}O{sub 3}–SnO{sub 2}/G) composite is fabricated via a chemical heat solvent method and utilized as anode material for lithium ion batteries. The added B{sub 2}O{sub 3} dramatically improves the electrochemical performance of lithium ion batteries compared to the SnO{sub 2}/G composite. The B{sub 2}O{sub 3}–SnO{sub 2}/G composites as anode show an outstanding discharge capacity of 1404.9 mAh g{sup −1} at 500 mA g{sup −1} after 200 cycles and an excellent rate capacity, which apparently outperforms the previously reported SnO{sub 2}-based anode material. These improved electrochemical performance characteristics are due to the B{sub 2}O{sub 3} played a buffering role, which are easily beneficial for accommodating the volume change during the lithium ions insertion/extraction processes. Furthermore, boron atoms can accept electrons for its electron-deficient nature and boron ions could release electrons, which lead to electrons' increased density and conductivity are increased. The results indicate that the B{sub 2}O{sub 3}–SnO{sub 2}/G composite is a promising anode material for lithium ion batteries.

Sponge-like reduced graphene oxide/silicon/carbon nanotube composites for lithium ion batteries

Science.gov (United States)

Fang, Menglu; Wang, Zhao; Chen, Xiaojun; Guan, Shiyou

2018-04-01

Three-dimensional sponge-like reduced graphene oxide/silicon/carbon nanotube composites were synthesized by one-step hydrothermal self-assembly using silicon nanoparticles, graphene oxide and amino modified carbon nanotubes to develop high-performance anode materials of lithium ion batteries. Scanning electron microscopy and transmission electron microscopy images show the structure of composites that Silicon nanoparticles are coated with reduced graphene oxide while amino modified carbon nanotubes wrap around the reduced graphene oxide in the composites. When applied to lithium ion battery, these composites exhibit high initial specific capacity of 2552 mA h/g at a current density of 0.05 A/g. In addition, reduced graphene oxide/silicon/carbon nanotube composites also have better cycle stability than bare Silicon nanoparticles electrode with the specific capacity of 1215 mA h/g after 100 cycles. The three-dimension sponge-like structure not only ensures the electrical conductivity but also buffers the huge volume change, which has broad potential application in the field of battery.

Si clusters/defective graphene composites as Li-ion batteries anode materials: A density functional study

International Nuclear Information System (INIS)

Li, Meng; Liu, Yue-Jie; Zhao, Jing-xiang; Wang, Xiao-guang

2015-01-01

Highlights: • We study the interaction between Si clusters with pristine and defective graphene. • We find that the binding strength of Si clusters on graphene can be enhanced to different degrees after introducing various defects. • It is found that both graphene and Si cluster in the Si/graphene composites can preserve their Li uptake ability. - Abstract: Recently, the Si/graphene hybrid composites have attracted considerable attention due to their potential application for Li-ion batteries. How to effectively anchor Si clusters to graphene substrates to ensure their stability is an important factor to determine their performance for Li-ion batteries. In the present work, we have performed comprehensive density functional theory (DFT) calculations to investigate the geometric structures, stability, and electronic properties of the deposited Si clusters on defective graphenes as well as their potential applications for Li-ion batteries. The results indicate that the interfacial bonding between these Si clusters with the pristine graphene is quietly weak with a small adsorption energy (<−0.21 eV). Due to the presence of vacancy site, the binding strength of Si clusters on defective graphene is much stronger than that of pristine one, accompanying with a certain amount of charge transfer from Si clusters to graphene substrates. Moreover, the ability of Si/graphene hybrids for Li uptake is studied by calculating the adsorption of Li atoms. We find that both graphenes and Si clusters in the Si/graphene composites preserve their Li uptake ability, indicating that graphenes not only server as buffer materials for accommodating the expansion of Si cluster, but also provide additional intercalation sites for Li

Composite sorbents of inorganic ion-exchangers and polyacrylonitrile binding matrix. Methods of modification of properties of inorganic ion-exchangers for application in column packed beds

International Nuclear Information System (INIS)

Sebesta, F.

1997-01-01

Methods of preparation of granules of inorganic ion exchangers as well as methods for improvement of granular strength of these materials are reviewed. The resulting ion exchangers are classified in three groups - 'intrinsic', supported and composite ion exchangers. Their properties are compared and possibilities of their technological application are evaluated. A new method of preparation of inorganic-organic composite sorbents of inorganic ion-exchangers and polyacrylonitrile binding matrix is described, advantages and disadvantages of such sorbents are discussed. Proposed fields of application include tratment of liquid radioactive and/or hazardous wastes, decontamination of natural water as well as analytical applications. (author)

Testing electric field models using ring current ion energy spectra from the Equator-S ion composition (ESIC instrument

Directory of Open Access Journals (Sweden)

L. M. Kistler

Full Text Available During the main and early recovery phase of a geomagnetic storm on February 18, 1998, the Equator-S ion composition instrument (ESIC observed spectral features which typically represent the differences in loss along the drift path in the energy range (5–15 keV/e where the drift changes from being E × B dominated to being gradient and curvature drift dominated. We compare the expected energy spectra modeled using a Volland-Stern electric field and a Weimer electric field, assuming charge exchange along the drift path, with the observed energy spectra for H⁺ and O⁺. We find that using the Weimer electric field gives much better agreement with the spectral features, and with the observed losses. Neither model, however, accurately predicts the energies of the observed minima.

Key words. Magnetospheric physics (energetic particles trapped; plasma convection; storms and substorms

Product ion isotopologue pattern: A tool to improve the reliability of elemental composition elucidations of unknown compounds in complex matrices.

Science.gov (United States)

Kaufmann, A; Walker, S; Mol, G

2016-04-15

Elucidation of the elemental compositions of unknown compounds (e.g., in metabolomics) generally relies on the availability of accurate masses and isotopic ratios. This study focuses on the information provided by the abundance ratio within a product ion pair (monoisotopic versus the first isotopic peak) when isolating and fragmenting the first isotopic ion (first isotopic mass spectrum) of the precursor. This process relies on the capability of the quadrupole within the Q Orbitrap instrument to isolate a very narrow mass window. Selecting only the first isotopic peak (first isotopic mass spectrum) leads to the observation of a unique product ion pair. The lighter ion within such an isotopologue pair is monoisotopic, while the heavier ion contains a single carbon isotope. The observed abundance ratio is governed by the percentage of carbon atoms lost during the fragmentation and can be described by a hypergeometric distribution. The observed carbon isotopologue abundance ratio (product ion isotopologue pattern) gives reliable information regarding the percentage of carbon atoms lost in the fragmentation process. It therefore facilitates the elucidation of the involved precursor and product ions. Unlike conventional isotopic abundances, the product ion isotopologue pattern is hardly affected by isobaric interferences. Furthermore, the appearance of these pairs greatly aids in cleaning up a 'matrix-contaminated' product ion spectrum. The product ion isotopologue pattern is a valuable tool for structural elucidation. It increases confidence in results and permits structural elucidations for heavier ions. This tool is also very useful in elucidating the elemental composition of product ions. Such information is highly valued in the field of multi-residue analysis, where the accurate mass of product ions is required for the confirmation process. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Fricção em braquetes gerada por fios de aço inoxidável, superelásticos com IonGuard e sem IonGuard Friction force on brackets generated by stainless steel wire and superelastic wires with and without IonGuard

Directory of Open Access Journals (Sweden)

Luiz Carlos Campos Braga

2011-08-01

Full Text Available OBJETIVO: o objetivo deste estudo foi verificar a fricção no braquete (Roth, Composite, 10.17.005, 3,2mm, largura 0,022" x 0,030", Torque -2° e angulação +13°, Morelli®, Brasil, utilizando fios ortodônticos retangulares de 0,019" x 0,025" de aço inoxidável (Morelli®, Brasil e de níquel-titânio superelásticos Bioforce com IonGuard e sem IonGuard (Bioforce, GAC®, EUA. MÉTODOS: foram utilizados 24 conjuntos braquetes/segmento de fio, divididos em 3 grupos de acordo com o fio. Cada conjunto braquete/segmento de fio foi testado 3 vezes e obtida uma média. Os ensaios foram realizados em máquina universal de ensaios EMIC DL2000®. Os dados foram submetidos à Análise de Variância com significância de 95%. RESULTADOS: o fio retangular Bioforce com IonGuard apresentou fricção significativamente menor que o Bioforce sem IonGuard, porém sem diferença do fio de aço inoxidável. Entretanto, o coeficiente de variação dos fios Bioforce com e sem IonGuard foi menor que o do fio de aço inoxidável. CONCLUSÃO: os fios retangulares de 0,019" x 0,025" Bioforce com IonGuard apresentam menor fricção que o fio Bioforce sem IonGuard, sem diferença para o fio de aço inoxidável.OBJECTIVE: The aim of this study was to evaluate the friction forces on brackets (Roth, Composite, 10.17.005, 3.2 mm, width 0.022" x 0.030 ", Torque -2° and angulation +13°, Morelli®, Brazil, with stainless steel orthodontic rectangular wire (Morelli®, Brazil and nickel titanium superelastic Bioforce wires with and without IonGuard (Bioforce, GAC®, USA. MATERIAL AND METHODS: Twenty-four brackets/wire segment combinations were used, distributed into three groups according to the orthodontic wire. Each bracket/wire segment combination was tested three times. The tests were performed in a universal testing machine Emic DL2000®. The data was submitted to ANOVA one way followed by Tukey's post hoc test (p<0.05. RESULTS: The rectangular orthodontic Bioforce wire

Germline Mutations in Cancer Predisposition Genes are Frequent in Sporadic Sarcomas

OpenAIRE

Chan, Sock Hoai; Lim, Weng Khong; Ishak, Nur Diana Binte; Li, Shao-Tzu; Goh, Wei Lin; Tan, Gek San; Lim, Kiat Hon; Teo, Melissa; Young, Cedric Ng Chuan; Malik, Simeen; Tan, Mann Hong; Teh, Jonathan Yi Hui; Chin, Francis Kuok Choon; Kesavan, Sittampalam; Selvarajan, Sathiyamoorthy

2017-01-01

Associations of sarcoma with inherited cancer syndromes implicate genetic predisposition in sarcoma development. However, due to the apparently sporadic nature of sarcomas, little attention has been paid to the role genetic susceptibility in sporadic sarcoma. To address this, we performed targeted-genomic sequencing to investigate the prevalence of germline mutations in known cancer-associated genes within an Asian cohort of sporadic sarcoma patients younger than 50 years old. We observed 13....

Dietary factors and microsatellite instability in sporadic colon carcinomas

NARCIS (Netherlands)

Diergaarde, B.; Braam, H.; Muijen, van G.N.P.; Ligtenberg, M.J.L.; Kok, F.J.; Kampman, E.

2003-01-01

Microsatellite instability (MSI) occurs in 10-20% of the sporadic colon carcinomas and appears to be primarily due to alterations in hMLH1 and hMSH2. Little is known about the role of diet in MSI-related colon carcinogenesis. We used data from a Dutch population-based case-control study on sporadic

Dietary factors and microsatellite instability in sporadic colon carcinomas.

NARCIS (Netherlands)

Diergaarde, B.; Braam, H.; Muijen, G.N.P. van; Ligtenberg, M.J.L.; Kok, F.J.; Kampman, E.

2003-01-01

Microsatellite instability (MSI) occurs in 10-20% of the sporadic colon carcinomas and appears to be primarily due to alterations in hMLH1 and hMSH2. Little is known about the role of diet in MSI-related colon carcinogenesis. We used data from a Dutch population-based case-control study on sporadic

Visual art therapy in sporadic Creutzfeldt-Jakob disease: a case study.

Science.gov (United States)

Shrestha, Rajeet; Trauger-Querry, Barbara; Loughrin, Athena; Appleby, Brian S

2016-01-01

This paper describes the diagnostic and treatment utility of visual art therapy in a case of sporadic Creutzfeldt-Jakob disease. Visual art therapy was compared longitudinally with clinical and neuroimaging data over five-month period in an autopsy-confirmed case of sporadic Creutzfeldt-Jakob disease of MM2-cortical subtype. Art therapy sessions and content were useful in ascertaining neuropsychiatric symptoms during the course of her illness. Art therapy offered a unique emotional and cognitive outlet as illness progressed. Patients and families affected by sporadic Creutzfeldt-Jakob disease may benefit from art therapy despite the rapidly progressive nature of the illness. Art therapy can also be useful for assessment of patients with sporadic Creutzfeldt-Jakob disease by healthcare professionals.

Case-Control Studies of Sporadic Enteric Infections: A Review and Discussion of Studies Conducted Internationally from 1990 to 2009

Science.gov (United States)

Fullerton, Kathleen E.; Scallan, Elaine; Kirk, Martyn D.; Mahon, Barbara E.; Angulo, Frederick J.; de Valk, Henriette; van Pelt, Wilfrid; Gauci, Charmaine; Hauri, Anja M.; Majowicz, Shannon; O’Brien, Sarah J.

2015-01-01

Epidemiologists have used case-control studies to investigate enteric disease outbreaks for many decades. Increasingly, case-control studies are also used to investigate risk factors for sporadic (not outbreak-associated) disease. While the same basic approach is used, there are important differences between outbreak and sporadic disease settings that need to be considered in the design and implementation of the case-control study for sporadic disease. Through the International Collaboration on Enteric Disease “Burden of Illness” Studies (the International Collaboration), we reviewed 79 case-control studies of sporadic enteric infections caused by nine pathogens that were conducted in 22 countries and published from 1990 through to 2009. We highlight important methodological and study design issues (including case definition, control selection, and exposure assessment) and discuss how approaches to the study of sporadic enteric disease have changed over the last 20 years (e.g., making use of more sensitive case definitions, databases of controls, and computer-assisted interviewing). As our understanding of sporadic enteric infections grows, methods and topics for case-control studies are expected to continue to evolve; for example, advances in understanding of the role of immunity can be used to improve control selection, the apparent protective effects of certain foods can be further explored, and case-control studies can be used to provide population-based measures of the burden of disease. PMID:22443481

Composition dependent thermal annealing behaviour of ion tracks in apatite

Energy Technology Data Exchange (ETDEWEB)

Nadzri, A., E-mail: allina.nadzri@anu.edu.au [Department of Electronic Materials Engineering, Research School of Physics and Engineering, Australian National University, Canberra, ACT 2601 (Australia); Schauries, D.; Mota-Santiago, P.; Muradoglu, S. [Department of Electronic Materials Engineering, Research School of Physics and Engineering, Australian National University, Canberra, ACT 2601 (Australia); Trautmann, C. [GSI Helmholtz Centre for Heavy Ion Research, Planckstrasse 1, 64291 Darmstadt (Germany); Technische Universität Darmstadt, 64287 Darmstadt (Germany); Gleadow, A.J.W. [School of Earth Science, University of Melbourne, Melbourne, VIC 3010 (Australia); Hawley, A. [Australian Synchrotron, 800 Blackburn Road, Clayton, VIC 3168 (Australia); Kluth, P. [Department of Electronic Materials Engineering, Research School of Physics and Engineering, Australian National University, Canberra, ACT 2601 (Australia)

2016-07-15

Natural apatite samples with different F/Cl content from a variety of geological locations (Durango, Mexico; Mud Tank, Australia; and Snarum, Norway) were irradiated with swift heavy ions to simulate fission tracks. The annealing kinetics of the resulting ion tracks was investigated using synchrotron-based small-angle X-ray scattering (SAXS) combined with ex situ annealing. The activation energies for track recrystallization were extracted and consistent with previous studies using track-etching, tracks in the chlorine-rich Snarum apatite are more resistant to annealing than in the other compositions.

Electrolyte compositions for lithium ion batteries

Science.gov (United States)

Sun, Xiao-Guang; Dai, Sheng; Liao, Chen

2016-03-29

The invention is directed in a first aspect to an ionic liquid of the general formula Y.sup.+Z.sup.-, wherein Y.sup.+ is a positively-charged component of the ionic liquid and Z.sup.- is a negatively-charged component of the ionic liquid, wherein Z.sup.- is a boron-containing anion of the following formula: ##STR00001## The invention is also directed to electrolyte compositions in which the boron-containing ionic liquid Y.sup.+Z.sup.- is incorporated into a lithium ion battery electrolyte, with or without admixture with another ionic liquid Y.sup.+X.sup.- and/or non-ionic solvent and/or non-ionic solvent additive.

Adsorption of Cadmium Ions from Water on Double-walled Carbon Nanotubes/Iron Oxide Composite

Directory of Open Access Journals (Sweden)

Karima Seffah

2017-12-01

Full Text Available A new material (DWCNT/iron oxide for heavy metals removal was developed by combining the adsorption features of double-walled carbon nanotubes with the magnetic properties of iron oxides. Batch experiments were applied in order to evaluate adsorption capacity of the DWCNT/iron oxide composite for cadmium ions. The influence of operating parameters such as pH value, amount of adsorbent, initial adsorbate concentration and agitation speed was studied. The adsorption capacity of the DWCNT/iron oxide adsorbent for Cd2+ ions was 20.8 mg g-1, which is at the state of the art. The obtained results revealed that DWCNT/iron oxide composite is a very promising adsorbent for removal of Cd2+ ions from water under natural conditions. The advantage of the magnetic composite is that it can be used as adsorbent for contaminants in water and can be subsequently controlled and removed from the medium by a simple magnetic process.

Swift heavy ions induced surface modifications in Ag-polypyrrole composite films synthesized by an electrochemical route

International Nuclear Information System (INIS)

Kumar, Vijay; Ali, Yasir; Sharma, Kashma; Kumar, Vinod; Sonkawade, R.G.; Dhaliwal, A.S.; Swart, H.C.

2014-01-01

Highlights: • Two steps electrochemical synthesis for the fabrication of Ag-polypyrrole composite films. • Surface modifications by swift heavy ion beam. • SEM image shows the formation of craters and humps after irradiation. • Detailed structural analysis by Raman spectroscopy. - Abstract: The general aim of this work was to study the effects of swift heavy ions on the properties of electrochemically synthesized Ag-polypyrrole composite thin films. Initially, polypyrrole (PPy) films were electrochemically synthesized on indium tin oxide coated glass surfaces using a chronopotentiometery technique, at optimized process conditions. The prepared PPy films have functioned as working electrodes for the decoration of submicron Ag particles on the surface of the PPy films through a cyclicvoltammetry technique. Towards probing the effect of swift heavy ion irradiation on the structural and morphological properties, the composite films were subjected to a 40 MeV Li 3+ ion beam irradiation for various fluences (1 × 10 11 , 1 × 10 12 and 1 × 10 13 ions/cm 2 ). Comparative microstructural investigations were carried out after the different ion fluences using scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy and micro-Raman spectroscopy techniques. Raman and SEM studies revealed that the structure of the films became disordered after irradiation. The SEM studies of irradiated composite films show significant changes in their surface morphologies. The surface was smoother at lower fluence but craters were observed at higher fluence

Swift heavy ions induced surface modifications in Ag-polypyrrole composite films synthesized by an electrochemical route

Energy Technology Data Exchange (ETDEWEB)

Kumar, Vijay, E-mail: vijays_phy@rediffmail.com [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein ZA 9300 (South Africa); Ali, Yasir [Department of Physics, Sant Longowal Institute of Engineering and Technology, Longowal, District Sangrur 148106, Punjab (India); Sharma, Kashma [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein ZA 9300 (South Africa); Department of Chemistry, Shoolini University of Biotechnology and Management Sciences, Solan 173212 (India); Kumar, Vinod [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein ZA 9300 (South Africa); Sonkawade, R.G. [Inter University Accelerator Center, Aruna Asif Ali Marg, New Delhi 110067 (India); Dhaliwal, A.S. [Department of Physics, Sant Longowal Institute of Engineering and Technology, Longowal, District Sangrur 148106, Punjab (India); Swart, H.C., E-mail: swarthc@ufs.ac.za [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein ZA 9300 (South Africa)

2014-03-15

Highlights: • Two steps electrochemical synthesis for the fabrication of Ag-polypyrrole composite films. • Surface modifications by swift heavy ion beam. • SEM image shows the formation of craters and humps after irradiation. • Detailed structural analysis by Raman spectroscopy. - Abstract: The general aim of this work was to study the effects of swift heavy ions on the properties of electrochemically synthesized Ag-polypyrrole composite thin films. Initially, polypyrrole (PPy) films were electrochemically synthesized on indium tin oxide coated glass surfaces using a chronopotentiometery technique, at optimized process conditions. The prepared PPy films have functioned as working electrodes for the decoration of submicron Ag particles on the surface of the PPy films through a cyclicvoltammetry technique. Towards probing the effect of swift heavy ion irradiation on the structural and morphological properties, the composite films were subjected to a 40 MeV Li{sup 3+} ion beam irradiation for various fluences (1 × 10{sup 11}, 1 × 10{sup 12} and 1 × 10{sup 13} ions/cm{sup 2}). Comparative microstructural investigations were carried out after the different ion fluences using scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy and micro-Raman spectroscopy techniques. Raman and SEM studies revealed that the structure of the films became disordered after irradiation. The SEM studies of irradiated composite films show significant changes in their surface morphologies. The surface was smoother at lower fluence but craters were observed at higher fluence.

Fabrication of submicron structures in nanoparticle/polymer composite by holographic lithography and reactive ion etching

Science.gov (United States)

Zhang, A. Ping; He, Sailing; Kim, Kyoung Tae; Yoon, Yong-Kyu; Burzynski, Ryszard; Samoc, Marek; Prasad, Paras N.

2008-11-01

We report on the fabrication of nanoparticle/polymer submicron structures by combining holographic lithography and reactive ion etching. Silica nanoparticles are uniformly dispersed in a (SU8) polymer matrix at a high concentration, and in situ polymerization (cross-linking) is used to form a nanoparticle/polymer composite. Another photosensitive SU8 layer cast upon the nanoparticle/SU8 composite layer is structured through holographic lithography, whose pattern is finally transferred to the nanoparticle/SU8 layer by the reactive ion etching process. Honeycomb structures in a submicron scale are experimentally realized in the nanoparticle/SU8 composite.

Bulk-compositional changes of Ni2Al3 and NiAl3 during ion etching

International Nuclear Information System (INIS)

Chen Houwen; Wang Rong

2008-01-01

Bulk-compositional changes of Ni 2 Al 3 and NiAl 3 in a Ni-50 wt% Al alloy during ion etching have been investigated by transmission electron microscopy and energy dispersive X-ray spectroscopic analyses. After etching with 7, 5 and 3 keV Ar + ions for 15, 24 and 100 h nickel contents in both Ni 2 Al 3 and NiAl 3 exceeded greatly those in the initial compounds and increased with the decrement of the sputtering energy. After 100 h etching with 3 keV Ar + ions the compositions of these two compounds reached a similar value, about Ni 80-83 Al 12-15 Fe 3-4 Cr 1-2 (at%). A synergistic action of preferential sputtering, radiation-induced segregation and radiation-enhanced diffusion enables the altered-layers at the top and bottom of the film extend through the whole film. The bulk-compositional changes are proposed to occur in the unsteady-state sputtering regime of ion etching and caused by an insufficient supply of matter in a thin film

Legionnaires’ Disease: Clinicoradiological Comparison of Sporadic Versus Outbreak Cases

Directory of Open Access Journals (Sweden)

Hafiz Rizwan Talib Hashmi

2017-06-01

Full Text Available Background: In 2015, New York City experienced the worst outbreak of Legionnaires’ disease in the history of the city. We compare patients seen during the 2015 outbreak with sporadic cases of Legionella during the past 5 years. Methods: We conducted a retrospective chart review of 90 patients with Legionnaires’ disease, including sporadic cases of Legionella infection admitted from 2010 to 2015 (n = 55 and cases admitted during the 2015 outbreak (n = 35. Results: We saw no significant differences between the 2 groups regarding demographics, smoking habits, alcohol intake, underlying medical disease, or residence type. Univariate and multivariate analyses showed that patients with sporadic case of Legionella had a longer stay in the hospital and intensive care unit as well as an increased stay in mechanical ventilation. Short-term mortality, discharge disposition, and most clinical parameters did not differ significantly between the 2 groups. Conclusions: We found no specific clinicoradiological characteristics that could differentiate sporadic from epidemic cases of Legionella . Early recognition and high suspicion for Legionnaires’ disease are critical to provide appropriate treatment. Cluster of cases should increase suspicion for an outbreak.

Mechanical properties of MeV ion-irradiated SiC/SiC composites characterized by indentation technique

International Nuclear Information System (INIS)

Park, J.Y.; Park, K.H.; Kim, W.; Kishimoto, H.; Kohyama, A.

2007-01-01

Full text of publication follows: SiC/SiC composites have been considered as a structural material for advanced fusion concepts. In the core of fusion reactor, those SiC/SiC composites are experienced the complex attacks such as strong neutron, high temperature and transmuted gases. One of the vital data for designing the SiC/SiC composites to the fusion reactor is mechanical properties under the severe neutron irradiation. In this work, various SiC/SiC composites were prepared by the different fabrication processes like CVI (chemical vapor infiltration), WA-CVI (SiC whisker assisted CVI) and hot-pressed method. The expected neutron irradiation was simulated by a silicon self-ion irradiation at a DuET facility; Dual-beam for Energy Technologies, Kyoto University. The irradiation temperature were 600 deg. C and 1200 deg. C, and the irradiation does were 5 dpa and 20 dpa, respectively. The 5.1 MeV Si ions were irradiated to the intrinsic CVI-SiC, SiC whisker reinforced SiC and SiC composites produced by hot-press method. The mechanical properties like hardness, elastic modulus and fracture toughness were characterized by an indentation technique. The ion irradiation caused the increase of the hardness and fracture toughness, which was dependent on the irradiation temperature. SiC whisker reinforcement in the SiC matrix accelerated the increase of the fracture toughness by the ion irradiation. For SiC/SiC composites after the ion irradiation, this work will provide the additional data for the mechanical properties as well as the effect of SiC whisker reinforcement. (authors)

Experimental composite guidance conduits for peripheral nerve repair: An evaluation of ion release

Energy Technology Data Exchange (ETDEWEB)

Zhang, X.F. [Department of Biological Sciences and Medical Engineering Design and Innovation Centre, Cork Institute of Technology, Cork (Ireland); Coughlan, A. [Inamori School of Engineering, Alfred University, Alfred, NY. 14802 (United States); O' Shea, H. [Department of Biological Sciences and Medical Engineering Design and Innovation Centre, Cork Institute of Technology, Cork (Ireland); Towler, M.R. [Inamori School of Engineering, Alfred University, Alfred, NY. 14802 (United States); Kehoe, S., E-mail: sharonkehoe@dal.ca [Department of Applied Oral Sciences, Dalhousie University, Halifax, NS, B3H 4R2 (Canada); School of Biomedical Engineering, Dalhousie University, Halifax, NS, B3H 4R2 (Canada); Boyd, D., E-mail: d.boyd@dal.ca [Department of Applied Oral Sciences, Dalhousie University, Halifax, NS, B3H 4R2 (Canada); School of Biomedical Engineering, Dalhousie University, Halifax, NS, B3H 4R2 (Canada)

2012-08-01

Poly (lactide-co-glycolide) (PLGA) - Pluronic F127 - glass composites have demonstrated excellent potential, from the perspective of controlled mechanical properties and cytocompatibility, for peripheral nerve regeneration. In addition to controlling the mechanical properties and cytotoxicity for such composite devices, the glass component may mediate specific responses upon implantation via degradation in the physiological environment and release of constituent elements. However, research focused on quantifying the release levels of such therapeutic ions from these experimental medical devices has been limited. To redress the balance, this paper explores the ion release profiles for Si{sup 4+}, Ca{sup 2+}, Na{sup +}, Zn{sup 2+}, and Ce{sup 4+} from experimental composite nerve guidance conduits (CNGC) comprising PLGA (at 12.5, and 20 wt.%), F127 (at 0, 2.5 and 5 wt.%) and various loadings of Si-Ca-Na-Zn-Ce glass (at 20 and 40 wt.%) for incubation periods of up to 28 days. The concentration of each ion, at various time points, was determined using Inductively Coupled Plasma-Atomic Emission Spectrometry (Perkin Elmer Optima 3000). It was observed that the Si{sup 4+}, Na{sup +}, Ca{sup 2+}, Zn{sup 2+} release from CNGCs in this study ranged from 0.22 to 6.477 ppm, 2.307 to 3.277 ppm, 40 to 119 ppm, and 45 to 51 ppm, respectively. The Ce{sup 4+} concentrations were under the minimum detection limits for the ICP instrument utilized. The results indicate that the ion release levels may be appropriate to mediate therapeutic effects with respect to peripheral nerve regeneration. The data generated in this paper provides requisite evidence to optimize composition for pre-clinical evaluation of the experimental composite. - Graphical abstract: Highlights: Black-Right-Pointing-Pointer Time-dependent degradation studies of PLGA/glass composite nerve guidance conduits (NGCs). Black-Right-Pointing-Pointer Si{sup 4+}, Na{sup +}, Ca{sup 2+} and Zn{sup 2+} release levels for the

Electron cyclotron resonance (E.C.R.) multiply charged ion sources

International Nuclear Information System (INIS)

Geller, R.

1978-01-01

High charge state ions can be produced by electron bombardment inside targets when the target electron density n (cm -3 ) multiplied by the ion transit time through the target tau (sec) is: n tau > 5.10 9 cm -3 sec. The relative velocity between electrons and ions determines the balance between stripping and capture i.e. the final ion charge state. (In a stripper foil fast ions interact with slow electrons involving typically n approximately 10 24 cm -3 , tau approximately 10 -14 sec). In the E.C.R. source a cold ion plasma created in a first stage diffuses slowly through a second stage containing a hot E.C.R. plasma with n > 3.10 11 cm -3 and tau > 10 -2 sec. Continuous beams of several μA of C 6+ N 7+ Ne 9+ A 11+ are extracted from the second stage with normalized emittances of approximately 0.5 π mm mrad. The absence of cathodes and plasma arcs makes the source very robust, reliable and well-fitted for cyclotron injection. A super conducting source is under development

Kinetics and equilibrium studies for sorption of Cu (II) and Cr (VI) ions onto polymeric composite resins

International Nuclear Information System (INIS)

El-Zahhhar, A.A.; Abdel-Aziz, H.M.; Siyam, T.

2005-01-01

The sorption behavior of Cu (II) and Cr (VI) ions from aqueous solutions was studied using polymeric composite resins. Batch sorption experiments were performed as a function of hydrogen ion concentration, complexing agent concentration, resin weight and ionic strength. Kinetic parameters as a function of initial ion concentration were determined to predict the sorption behavior of Cu (II) and Cr (VI) onto polymeric composite resins. The equilibrium data could be fitted by the frendlich adsorption isotherm equation

Response of thermal ions to electromagnetic ion cyclotron waves

Science.gov (United States)

Anderson, B. J.; Fuselier, S. A.

1994-01-01

Electromagnetic ion cyclotron waves generated by 10 - 50 keV protons in the Earth's equatorial magnetosphere will interact with the ambient low-energy ions also found in this region. We examine H(+) and He(+) distribution functions from approx. equals 1 to 160 eV using the Hot Plasma Composition Experiment instrument on AMPTE/CCE to investigate the thermal ion response to the waves. A total of 48 intervals were chosen on the basis of electromagnetic ion cyclotron (EMIC) wave activity: 24 with prevalent EMIC waves and 24 with no EMIC waves observed on the orbit. There is a close correlation between EMIC waves and perpendicular heated ion distributions. For protons the perpendicular temperature increase is modest, about 5 eV, and is always observed at 90 deg pitch angles. This is consistent with a nonresonant interaction near the equator. By contrast, He(+) temperatures during EMIC wave events averaged 35 eV and sometimes exceeded 100 eV, indicating stronger interaction with the waves. Furthermore, heated He(+) ions have X-type distributions with maximum fluxes occurring at pitch angles intermediate between field-aligned and perpendicular directions. The X-type He(+) distributions are consistent with a gyroresonant interaction off the equator. The concentration of He(+) relative to H(+) is found to correlate with EMIC wave activity, but it is suggested that the preferential heating of He(+) accounts for the apparent increase in relative He(+) concentration by increasing the proportion of He(+) detected by the ion instrument.

Possible mechanisms for the interaction of polymeric composite resins with Cu(II) ions in aqueous solution

International Nuclear Information System (INIS)

El-Zahhhar, A.A.; Abdel-Aziz, H.M.; Siyam, T.

2005-01-01

The interaction between the active groups of polymeric composite resins such as Poly(acrylamide-acrylic acid)-ethylenediaminetetra acetic acid disodium salt P(AM-AA)EDTANa 2 , Poly(acrylamide-acrylic acid)- montmorillonite P(AM-AA)-montmorillonite, and Poly(acrylamide-acrylic acid)-potassium nickel hexacyanoferrate P(AM-AA)-KNiHCF, with copper sulfate as a test ion has been studied. The spectroscopic studies show that the mechanism of interaction between polymeric composite resins and copper sulfate is a bond formation between the active groups of polymeric chains and copper ion. The bond formation depends on nature of polymeric chains. It was also found that the amide groups form complexes with hydrated cations, while carboxylate group interact by ion exchange mechanism through complex formation. Montmorillonite and hexacyanoferrate of the resins interact with metal ions by ion exchange mechanism

Steady State Sputtering Yields and Surface Compositions of Depleted Uranium and Uranium Carbide bombarded by 30 keV Gallium or 16 keV Cesium Ions.

Energy Technology Data Exchange (ETDEWEB)

Siekhaus, W. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Teslich, N. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Weber, P. K. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2014-10-23

Depleted uranium that included carbide inclusions was sputtered with 30-keV gallium ions or 16-kev cesium ions to depths much greater than the ions’ range, i.e. using steady-state sputtering. The recession of both the uranium’s and uranium carbide’s surfaces and the ion corresponding fluences were used to determine the steady-state target sputtering yields of both uranium and uranium carbide, i.e. 6.3 atoms of uranium and 2.4 units of uranium carbide eroded per gallium ion, and 9.9 uranium atoms and 3.65 units of uranium carbide eroded by cesium ions. The steady state surface composition resulting from the simultaneous gallium or cesium implantation and sputter-erosion of uranium and uranium carbide were calculated to be U₈₆Ga₁₄, (UC)₇₀Ga₃₀ and U₈₁Cs₉, (UC)₇₉Cs₂₁, respectively.

Effect of elemental composition of ion beam on the phase formation and surface strengthening of structural materials

International Nuclear Information System (INIS)

Avdienko, K.I.; Avdienko, A.A.; Kovalenko, I.A.

2001-01-01

The investigation results are reported on the influence of ion beam element composition on phase formation, wear resistance and microhardness of surface layers of titanium alloys VT-4 and VT-16 as well as stainless steel 12Kh18N10T implanted with nitrogen, oxygen and boron. It is stated that ion implantation into structural materials results in surface hardening and is directly dependent on element composition of implanted ion beam. The presence of oxygen in boron or nitrogen ion beams prevents the formation of boride and nitride phases thus decreasing a hardening effect [ru

Removal of Heavy Metal Ions by Using Composite of Cement Kiln Dust/Ethylene Glycol co Acrylic Acid Prepared by y-Irradiation

International Nuclear Information System (INIS)

Sokker, H.H.; Abdel-Rahman, H.A.; Khattab, M.M.; Ismail, M.R.

2010-01-01

Various composites of cement kiln dust (CKD) and poly(ethylene glycol co acrylic acid) using y-irradiation was investigated. The samples were prepared using three percentages of cement kiln dust namely, 20, 50 and 75 by wt % and mixed with an equimolar ratio (1:1) of ethylene glycol and acrylic acid then irradiated at doses; 10,20 and 30 kGy of gamma-irradiation. The results showed that (CKD) and poly(ethylene glycol co acrylic acid) composites were formed only at 30 kGy. In addition, CKD alone has the lowest degree of removal of heavy metal ions compared with the prepared composites. A composite containing 75% cement kiln dust by weight percentage, showed the highest degree of removal of cobalt ions, whereas, a composite of 20% CKD showed the highest degree for cadmium ion removal. While the composite of 75% CKD showed a higher selectivity of cobalt ion than cadmium ion in their mixed solution.

Influence of iron substitution by selected rare-earth ions on the properties of NiZn ferrite fillers and PVC magneto-polymer composites

Science.gov (United States)

Ušák, Elemír; Ušáková, Mariana; Dosoudil, Rastislav; Šoka, Martin; Dobročka, Edmund

2018-04-01

Nickel-zinc ferrites are very important soft magnetic materials from the point of view of diverse technical applications (such as, e.g., various electronic devices and components) for their high magnetic permeability and permittivity, low core loss, high resistivity, high Curie temperature as well as mechanical strength and chemical stability. Due to their good absorbing properties, they can be used as microwave absorbing and shielding materials with the aim of decreasing the environmental pollution caused by non-ionizing microwave radiation. The ferrite material incorporated into the polymer matrix creates qualitatively new magneto-polymer composite material taking benefits from both components. The properties typical for polymers (elasticity, mouldability, etc.) are combined with good high-frequency magnetic parameters, thus allowing to utilize these materials, e.g., in high-frequency applications where especially flexibility of composite materials plays a key role. Small amounts of selected rare-earth (RE) ions, in particular Y3+, La3+, Eu3+ and Gd3+ have been embedded into the nickel-zinc ferrite that has been used as the magnetic filler in magnetic polymer composites with polyvinylchloride (PVC) acting as the polymeric matrix. The effect of various types of rare-earth ions on the structural as well as quasi-static and dynamic (electro)magnetic properties of the ferrite fillers as well as ferrite/PVC composites, in particular the frequency dispersion of the complex permeability, has been studied.

Correlation of shear and dielectric ion viscosity of dental resins - Influence of composition, temperature and filler content.

Science.gov (United States)

Steinhaus, Johannes; Hausnerova, Berenika; Haenel, Thomas; Selig, Daniela; Duvenbeck, Fabian; Moeginger, Bernhard

2016-07-01

Shear viscosity and ion viscosity of uncured visible light-curing (VLC) resins and resin based composites (RBC) are correlated with respect to the resin composition, temperature and filler content to check where Dielectric Analysis (DEA) investigations of VLC RBC generate similar results as viscosity measurements. Mixtures of bisphenol A glycidyl methacrylate (Bis-GMA) and triethylene glycol dimethacrylate (TEGDMA) as well as the pure resins were investigated and compared with two commercial VLC dental resins and RBCs (VOCO, Arabesk Top and Grandio). Shear viscosity data was obtained using a Haake Mars III, Thermo Scientific. Ion viscosity measurements performed by a dielectric cure analyzer (DEA 231/1 Epsilon with Mini IDEX-Sensor, Netzsch-Gerätebau). Shear viscosity depends reciprocally on the mobility of molecules, whereas the ion viscosity also depends on the ion concentration as it is affected by both ion concentration and mixture viscosity. Except of pure TEGDMA, shear and ion viscosities depend on the resin composition qualitatively in a similar manner. Furthermore, shear and ion viscosities of the commercial VLC dental resins and composites exhibited the same temperature dependency regardless of filler content. Application of typical rheological models (Kitano and Quemada) revealed that ion viscosity measurements can be described with respect to filler contents of up to 30vol.%. Rheological behavior of a VLC RBC can be characterized by DEA under the condition that the ion concentration is kept constant. Both methods address the same physical phenomenon - motion of molecules. The proposed relations allows for calculating the viscosity of any Bis-GMA-TEGDMA mixture on the base of the viscosities of the pure components. This study demonstrated the applicability of DEA investigations of VLC RBCs with respect to quality assurance purposes. Copyright © 2016 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Efficient reduced graphene oxide grafted porous Fe3O4 composite as a high performance anode material for Li-ion batteries.

Science.gov (United States)

Bhuvaneswari, Subramani; Pratheeksha, Parakandy Muzhikara; Anandan, Srinivasan; Rangappa, Dinesh; Gopalan, Raghavan; Rao, Tata Narasinga

2014-03-21

Here, we report facile fabrication of Fe3O4-reduced graphene oxide (Fe3O4-RGO) composite by a novel approach, i.e., microwave assisted combustion synthesis of porous Fe3O4 particles followed by decoration of Fe3O4 by RGO. The characterization studies of Fe3O4-RGO composite demonstrate formation of face centered cubic hexagonal crystalline Fe3O4, and homogeneous grafting of Fe3O4 particles by RGO. The nitrogen adsorption-desorption isotherm shows presence of a porous structure with a surface area and a pore volume of 81.67 m(2) g(-1), and 0.106 cm(3) g(-1) respectively. Raman spectroscopic studies of Fe3O4-RGO composite confirm the existence of graphitic carbon. Electrochemical studies reveal that the composite exhibits high reversible Li-ion storage capacity with enhanced cycle life and high coulombic efficiency. The Fe3O4-RGO composite showed a reversible capacity ∼612, 543, and ∼446 mA h g(-1) at current rates of 1 C, 3 C and 5 C, respectively, with a coulombic efficiency of 98% after 50 cycles, which is higher than graphite, and Fe3O4-carbon composite. The cyclic voltammetry experiment reveals the irreversible and reversible Li-ion storage in Fe3O4-RGO composite during the starting and subsequent cycles. The results emphasize the importance of our strategy which exhibited promising electrochemical performance in terms of high capacity retention and good cycling stability. The synergistic properties, (i) improved ionic diffusion by porous Fe3O4 particles with a high surface area and pore volume, and (ii) increased electronic conductivity by RGO grafting attributed to the excellent electrochemical performance of Fe3O4, which make this material attractive to use as anode materials for lithium ion storage.

Magnetic storm injection of 0.9- to 16-keV/e solar and terrestrial ions into the high-altitude magnetosphere

International Nuclear Information System (INIS)

Balsiger, H.; Eberhardt, P.; Geiss, J.; Young, D.T.

1980-01-01

The Geos 1 ion composition experiments has surveyed the plasma composition in the energy per charge range below 16 keV/e at all local times and at L=3--8. During quiet and moderately disturbed times, H + is the dominant species with a few percent of heavy (M/Q>1) ions. Substorms and storms increase the relative amount of heavy ions, and occasionally, they can become the dominant species in the outer magnetosphere. Two sources, the solar wind (characterized by 4 He ++ ) and the ionosphere (characterized by O + ), give on the average comparable contributions to storm time plasma, although in individual storms one or the other may dominate. Data presented here suggest that high-altitude thermal plasma or the plasmasphere (characterized by He + and O ++ ) must be considered as a third source. Under storm conditions with Geos in the dawn-noon local time sector we have observed a mixed composition region just inside the magnetopause where high fluxes of H + , He ++ , O + , and occasionally He + ions are present. During several storms a composition profile could be measured down to Lapprox.3. Both O + and He + increase toward low altitudes, and O + (within our energy range) can become dominant at the inner edge of the ring current. On April 30, 1978, during a storm, O + contributed > or approx. =8% to the total local energy density of the ring current particles at L=4.1. In no storm has He + been observed to be the main constituent during the recovery phase. During storm recovery, H + and O + are the dominant ions, the H + /O + ratio remaining constant or even increasing during the days following the main phase of the storms. This suggests that charge exchange is not the only loss mechanism for the storm time ring current and/or that H + is replenished during the recovery phase

Sporadic colorectal polyps and mismatch repair proteins

Directory of Open Access Journals (Sweden)

Mahsa Molaei

2011-01-01

Full Text Available Background: Colorectal cancers often arise from benign polyps. Adenomatous polyps and serrated polyps progress step by step to adenocarcinoma and change into malignant cancers. Genetic and epigenetic changes have correlation with specific stages of polyp-adenocarcinoma progression and colorectal cancer histopathological changes. Aims: In this study we used immunohistochemistry (IHC staining in sporadic colorectal polyps to assay functional status of MLH1, MSH2, MSH6, and PMS2 proteins, to track genetic/epigenetic roles of this issue in our patients. Materials and Methods: In this cross-sectional study we assessed all patients who were admitted with sporadic colorectal polyps and underwent polypectomy in endoscopy department during 2004-2008. Result: IHC results were abnormal in 6.8% cases for MLH1, in 4.5% cases for MSH2, in 3% for MSH6, and in 4.8% for PMS2. In all cases with abnormal PMS2, MLH1 was also reported as abnormal. Same results were reported for abnormal MSH2, which is accompanied with abnormal MSH6 in all cases (P values < 0.001. There is no significant difference between IHC staining results, gender, dysplasia grade, adenomatous type, and invasion. On the other hand, there was significant difference between IHC staining results, polyp location, and mean age of patients. The same significant difference was between adenomatous polyps and serrated adenoma polyps by MLH1 and PMS2 (P values < 0.05. Conclusion: According to our findings, maybe MMR dysfunction is the cause of sporadic colorectal polyps in younger age and its increasing risk of dysplasia progression and malignancy progression is only in serrated adenoma. Sporadic polyps in left colon had a higher risk to progress to malignancies, and abnormal IHC staining for MLH1 and PMS2 in serrated polyps is much more than in other adenomatous polyps.

Near Earth Inner-Source and Interstellar Pickup Ions Observed with the Hot Plasma Composition Analyzer of the Magnetospheric Multiscale Mission Mms-Hpca

Science.gov (United States)

Gomez, R. G.; Fuselier, S. A.; Mukherjee, J.; Gonzalez, C. A.

2017-12-01

Pickup ions found near the earth are generally picked up in the rest frame of the solar wind, and propagate radially outward from their point of origin. While propagating, they simultaneously gyrate about the magnetic field. Pickup ions come in two general populations; interstellar and inner source ions. Interstellar ions originate in the interstellar medium, enter the solar system in a neutral charge state, are gravitationally focused on the side of the sun opposite their arrival direction and, are ionized when they travel near the sun. Inner-source ions originate at a location within the solar system and between the sun and the observation point. Both pickup ion populations share similarities in composition and charge states, so measuring of their dynamics, using their velocity distribution functions, f(v)'s, is absolutely essential to distinguishing them, and to determining their spatial and temporal origins. Presented here will be the results of studies conducted with the four Hot Plasma Composition Analyzers of the Magnetospheric Multiscale Mission (MMS-HPCA). These instruments measure the full sky (4π steradians) distribution functions of near earth plasmas at a 10 second cadence in an energy-to-charge range 0.001-40 keV/e. The instruments are also capable of parsing this combined energy-solid angle phase space with 22.5° resolution polar angle, and 11.25° in azimuthal angle, allowing for clear measurement of the pitch angle scattering of the ions.

Ultra-low-energy (<10 eV/u) ion beam bombardment effect on naked DNA

Energy Technology Data Exchange (ETDEWEB)

Thopan, P. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thongkumkoon, P. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Department of Biology, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Prakrajang, K. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Faculty of Science, Maejo University, Chiang Mai 50290 (Thailand); Suwannakachorn, D. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Yu, L.D., E-mail: yuld@thep-center.org [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand)

2014-05-01

Highlights: • Decelerated ultra-low energy ion beam bombarded naked DNA. • DNA form change induced by ion bombardment was investigated. • N-ion bombardment at 32 eV induced DNA single and double strand breaks. • Ar-ion bombardment at a-few-hundreds eV induced DNA single strand break. - Abstract: Since ion energy deposition in the ion-bombarded materials dominantly occurs in the low-energy range, it is very interesting to know effects from ultra-low-energy ion interaction with DNA for understanding ion-beam-induced genetic mutation. Tens-keV Ar- and N-ion beams were decelerated to ultra-low energy ranging from 20 to 100 eV, or only a few to 10 eV/u, to bombard naked plasmid DNA. The bombarded DNA was analyzed using gel electrophoresis for DNA form changes. The original DNA supercoiled form was found to change to relaxed and linear forms, indicating single or double strand breaks after bombarded by tens-eV ion beam. N-ion beam was found more effective in inducing DNA change and mutation than Ar-ion beam. The study demonstrated that the ion bombardment with energy as low as several-tens eV was able to break DNA strands and thus potentially to cause genetic modification of biological cells. The experimental results were discussed in terms of direct atomic collision between the ions and DNA atoms.

Ultra-low-energy (<10 eV/u) ion beam bombardment effect on naked DNA

International Nuclear Information System (INIS)

Thopan, P.; Thongkumkoon, P.; Prakrajang, K.; Suwannakachorn, D.; Yu, L.D.

2014-01-01

Highlights: • Decelerated ultra-low energy ion beam bombarded naked DNA. • DNA form change induced by ion bombardment was investigated. • N-ion bombardment at 32 eV induced DNA single and double strand breaks. • Ar-ion bombardment at a-few-hundreds eV induced DNA single strand break. - Abstract: Since ion energy deposition in the ion-bombarded materials dominantly occurs in the low-energy range, it is very interesting to know effects from ultra-low-energy ion interaction with DNA for understanding ion-beam-induced genetic mutation. Tens-keV Ar- and N-ion beams were decelerated to ultra-low energy ranging from 20 to 100 eV, or only a few to 10 eV/u, to bombard naked plasmid DNA. The bombarded DNA was analyzed using gel electrophoresis for DNA form changes. The original DNA supercoiled form was found to change to relaxed and linear forms, indicating single or double strand breaks after bombarded by tens-eV ion beam. N-ion beam was found more effective in inducing DNA change and mutation than Ar-ion beam. The study demonstrated that the ion bombardment with energy as low as several-tens eV was able to break DNA strands and thus potentially to cause genetic modification of biological cells. The experimental results were discussed in terms of direct atomic collision between the ions and DNA atoms

Effect of simultaneous ion irradiation on microstructural change of SiC/SiC composites at high temperature

International Nuclear Information System (INIS)

Taguchi, T.; Wakai, E.; Igawa, N.; Nogami, S.; Snead, L.L.; Hasegawa, A.; Jitsukawa, S.

2002-01-01

The effect of simultaneous triple ion irradiation of He, H and Si on microstructural evolution of two kinds of SiC/SiC composites (HNS composite (using Hi-Nicalon type S SiC fiber) and TSA composite (using Tyranno SA SiC fiber)) at 1000 deg. C has been investigated. The microstructure observations of SiC/SiC composites irradiated to 10 dpa were examined by transmission electron microscopy. He bubbles were hardly formed in matrix of TSA composite, but many helium bubbles and some cracks were observed at grain boundaries of matrix of HNS composite. He bubbles and cracks were not, on the other hand, observed in the both fiber fabrics of HNS and TSA composites. Debonding between fiber and carbon layer following irradiation region was not observed in the both composites. Under these irradiation conditions, TSA composite showed the better microstructural stability against ion beams irradiation than one of HNS composite

Composite ion-exchangers and their possible use in treatment of low/intermediate level liquid radioactive wastes

International Nuclear Information System (INIS)

Sebesta, F.; Motl, A.; John, J.

1993-01-01

A new method of preparation of composite inorganic-organic ion exchangers using modified polyacrylonitrile (PAN) as a binding polymer for the inorganic active component is described. This method enables incorporation of very fine to colloidal particles of active component in the binding polymer which increases the capacity and improves the kinetics of ion exchange of the resulting absorber. The proposed method can be applied on most of the inorganic ion exchangers known. Results of tests of some absorbers for treatment of radioactive wastes produced in the nuclear industry are given. For the removal of radiocesium from Long Term Fuel Storage Pond water at NPP Jaslovske Bohunice (Slovakia) NiFC-PAN composite ion exchanger has been tested. Excellent results have been achieved both at low and high (floating bed) flow rates in the course of treatment of up to 45,000 BV of pond water. The possibility of decreasing the total activity of the Biological Shield water from the same NPP below the 37 Bq/l discharge limit has been proved using NiFC-PAN and NaTiO-PAN composite ion exchangers. NiFC-PAN, NaTiO-PAN, MnO-PAN, M315-PAN and Na-Y-PAN composite ion exchangers were tested for removal of radiocesium, radiocobalt and radiomanganese from standard liquid radioactive wastes and concentrates from NPP Krsko, Croatia. Different combinations of absorbers have been tested for the treatment of Boron Recycle Hold-up, Waste Condensate and Waste Hold-up Tanks. Radium could be quantitatively removed from highly saline acid waste water from uranium underground leaching on Ba(Ca)SO 4 -PAN absorber

White matter involvement in sporadic Creutzfeldt-Jakob disease.

Science.gov (United States)

Caverzasi, Eduardo; Mandelli, Maria Luisa; DeArmond, Stephen J; Hess, Christopher P; Vitali, Paolo; Papinutto, Nico; Oehler, Abby; Miller, Bruce L; Lobach, Irina V; Bastianello, Stefano; Geschwind, Michael D; Henry, Roland G

2014-12-01

Sporadic Creutzfeldt-Jakob disease is considered primarily a disease of grey matter, although the extent of white matter involvement has not been well described. We used diffusion tensor imaging to study the white matter in sporadic Creutzfeldt-Jakob disease compared to healthy control subjects and to correlated magnetic resonance imaging findings with histopathology. Twenty-six patients with sporadic Creutzfeldt-Jakob disease and nine age- and gender-matched healthy control subjects underwent volumetric T1-weighted and diffusion tensor imaging. Six patients had post-mortem brain analysis available for assessment of neuropathological findings associated with prion disease. Parcellation of the subcortical white matter was performed on 3D T1-weighted volumes using Freesurfer. Diffusion tensor imaging maps were calculated and transformed to the 3D-T1 space; the average value for each diffusion metric was calculated in the total white matter and in regional volumes of interest. Tract-based spatial statistics analysis was also performed to investigate the deeper white matter tracts. There was a significant reduction of mean (P=0.002), axial (P=0.0003) and radial (P=0.0134) diffusivities in the total white matter in sporadic Creutzfeldt-Jakob disease. Mean diffusivity was significantly lower in most white matter volumes of interest (PCreutzfeldt-Jakob disease. Mean diffusivity reduction reflected concomitant decrease of both axial and radial diffusivity, without appreciable changes in white matter anisotropy. Tract-based spatial statistics analysis showed significant reductions of mean diffusivity within the white matter of patients with sporadic Creutzfeldt-Jakob disease, mainly in the left hemisphere, with a strong trend (P=0.06) towards reduced mean diffusivity in most of the white matter bilaterally. In contrast, by visual assessment there was no white matter abnormality either on T2-weighted or diffusion-weighted images. Widespread reduction in white matter mean

COMPOSITIONS BASED ON PALLADIUM(II AND COPPER(II COMPOUNDS, HALIDE IONS, AND BENTONITE FOR OZONE DECOMPOSITION

Directory of Open Access Journals (Sweden)

T. L. Rakitskaya

2017-05-01

bromide ion. For Cu(II-KBr/N-Bent composition, kinetic and calculation data show that, in the presence of bromide ions, copper(II inhibits the ozone decomposition. For Pd(II-KBr/NBent composition, it has been found that the maximum activity is attained at СPd(II = 1.02·10-5 mol/g. For bimetallic Pd(II- Cu(II-KBr/N-Bent composition, changes in τ0, τ1/2, k1/2, and Q1/2 parameters depending on a Pd(II content are similar to those for monometallic Pd(II-KBr/NBent composition; however, values of the parameters are higher for the monometallic system. Thus, the inhibiting effect of Cu(II is observed even in the presence of palladium(II.

Embedded Si/Graphene Composite Fabricated by Magnesium-Thermal Reduction as Anode Material for Lithium-Ion Batteries

Science.gov (United States)

Zhu, Jiangliu; Ren, Yurong; Yang, Bo; Chen, Wenkai; Ding, Jianning

2017-12-01

Embedded Si/graphene composite was fabricated by a novel method, which was in situ generated SiO2 particles on graphene sheets followed by magnesium-thermal reduction. The tetraethyl orthosilicate (TEOS) and flake graphite was used as original materials. On the one hand, the unique structure of as-obtained composite accommodated the large volume change to some extent. Simultaneously, it enhanced electronic conductivity during Li-ion insertion/extraction. The MR-Si/G composite is used as the anode material for lithium ion batteries, which shows high reversible capacity and ascendant cycling stability reach to 950 mAh·g-1 at a current density of 50 mA·g-1 after 60 cycles. These may be conducive to the further advancement of Si-based composite anode design.

Influence of both ion bombardment and chemical treatment processes on the electrical conductivity of PVC/poly aniline composites

International Nuclear Information System (INIS)

Gad, E.A.M.; Ashour, A.H.; Abdel-Hamid, H.M.; Sayed, W.M.

1999-01-01

In this article the changes in the electrical conductivity of PVC/poly aniline composites, as temperature consecutively increases, have been measured. The measurement were taken with correspondence to a control series of the composites under two processes:A. Composite samples bombarded with Ar + ions with fluence 2.44 x 10 13 beam ions /cm 2 ., sec 4 of 4 ke V beam energy where argon atoms can induce defects in the surface layer take place. Composite samples treated chemically with concentrated H 2 SO 4 as dopant which reacts with nitrogen atom in aniline. The measurements were also, done with the composites as the ratio of poly(aniline) stepped upward

Mesoporous Tin-Based Oxide Nanospheres/Reduced Graphene Composites as Advanced Anodes for Lithium-Ion Half/Full Cells and Sodium-Ion Batteries.

Science.gov (United States)

He, Yanyan; Li, Aihua; Dong, Caifu; Li, Chuanchuan; Xu, Liqiang

2017-10-04

The large volume variations of tin-based oxides hinder their extensive application in the field of lithium-ion batteries (LIBs). In this study, structure design, hybrid fabrication, and carbon-coating approaches have been simultaneously adopted to address these shortcomings. To this end, uniform mesoporous NiO/SnO 2 @rGO, Ni-Sn oxide@rGO, and SnO 2 @rGO nanosphere composites have been selectively fabricated. Among them, the obtained NiO/SnO 2 @rGO composite exhibited a high capacity of 800 mAh g -1 at 1000 mA g -1 after 400 cycles. The electrochemical mechanism of NiO/SnO 2 as an anode for LIBs has been preliminarily investigated by ex situ XRD pattern analysis. Furthermore, an NiO/SnO 2 @rGO-LiCoO 2 lithium-ion full cell showed a high capacity of 467.8 mAh g -1 at 500 mA g -1 after 100 cycles. Notably, the NiO/SnO 2 @rGO composite also showed good performance when investigated as an anode for sodium-ion batteries (SIBs). It is believed that the unique mesoporous nanospherical framework, synergistic effects between the various components, and uniform rGO wrapping of NiO/SnO 2 shorten the Li + ion diffusion pathways, maintain sufficient contact between the active material and the electrolyte, mitigate volume changes, and finally improve the electrical conductivity of the electrode. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

A Spinel-integrated P2-type Layered Composite: High-rate Cathode for Sodium-ion Batteries

Energy Technology Data Exchange (ETDEWEB)

Zheng, Jianming; Yan, Pengfei; Kan, Wang Hay; Wang, Chong M.; Manthiram, Arumugam

2016-01-14

Sodium-ion batteries (SIB) are being intensively investigated, owing to the natural abundance and low cost of Na resources. However, the SIBs still suffer from poor rate capability due to the large ionic radius of Na+ ion and the significant kinetic barrier to Na+-ion transport. Here, we present an Fd-3m spinel-integrated P2-type layered composite (P2 + Fd-3m) material as a high-rate cathode for SIBs. The P2 + Fd-3m composite material Na0.50Ni1/6Co1/6Mn2/3O2 shows significantly enhanced discharge capacity, energy density, and rate capability as compared to the pure P2-type counterpart. The composite delivers a high capacity of 85 mA h g-1 when discharging at a very high current density of 1500 mA g-1 (10C rate) between 2.0 and 4.5 V, validating it as a promising cathode candidate for high-power SIBs. The superior performance is ascribed to the improved kinetics in the presence of the integrated-spinel phase, which facilitates fast electron transport to coordinate with the timely Na+-ion insertion/extraction. The findings of this work also shed light on the importance of developing lattice doping, surface coating, and electrolyte additives to further improve the structural and interfacial stability of P2-type cathode materials and fully realize their practical applications in sodium-ion batteries.

Non-isothermal electrochemical model for lithium-ion cells with composite cathodes

Science.gov (United States)

Basu, Suman; Patil, Rajkumar S.; Ramachandran, Sanoop; Hariharan, Krishnan S.; Kolake, Subramanya Mayya; Song, Taewon; Oh, Dukjin; Yeo, Taejung; Doo, Seokgwang

2015-06-01

Transition metal oxide cathodes for Li-ion batteries offer high energy density and high voltage. Composites of these materials have shown excellent life expectancy and improved thermal performance. In the present work, a comprehensive non-isothermal electrochemical model for a Lithium ion cell with a composite cathode is developed. The present work builds on lithium concentration-dependent diffusivity and thermal gradient of cathode potential, obtained from experiments. The model validation is performed for a wide range of temperature and discharge rates. Excellent agreement is found for high and room temperature with moderate success at low temperatures, which can be attributed to the low fidelity of material properties at low temperature. Although the cell operation is limited by electronic conductivity of NCA at room temperature, at low temperatures a shift in controlling process is seen, and operation is limited by electrolyte transport. At room temperature, the lithium transport in Cathode appears to be the main source of heat generation with entropic heat as the primary contributor at low discharge rates and ohmic heat at high discharge rates respectively. Improvement in electronic conductivity of the cathode is expected to improve the performance of these composite cathodes and pave way for its wider commercialization.

Mechanisms of ion-bombardment-induced DNA transfer into bacterial E. coli cells

Energy Technology Data Exchange (ETDEWEB)

Yu, L.D., E-mail: yuld@thep-center.org [Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand); Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Sangwijit, K. [Molecular Biology Laboratory, Department of Biology, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Prakrajang, K. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Faculty of Science, Maejo University, Chiang Mai 50290 (Thailand); Phanchaisri, B. [Institute of Science and Technology Research, Chiang Mai University, Chiang Mai 50200 (Thailand); Thongkumkoon, P. [Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand); Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thopan, P. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Singkarat, S. [Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand); Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Anuntalabhochai, S. [Molecular Biology Laboratory, Department of Biology, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand)

2014-05-01

Highlights: • Ion bombardment could induce DNA transfer into E. coli cells. • The DNA transfer induction depended on ion energy and fluence. • The mechanism was associated with the bacterial cell envelope structure. • A mechanism phase diagram was proposed to summarize the mechanism. - Abstract: As a useful ion beam biotechnology, ion-bombardment-induced DNA transfer into bacterial Escherichia coli (E. coli) cells has been successfully operated using argon ions. In the process ion bombardment of the bacterial cells modifies the cell envelope materials to favor the exogenous DNA molecules to pass through the envelope to enter the cell. The occurrence of the DNA transfer induction was found ion energy and fluence dependent in a complex manner. At ion energy of a few keV and a few tens of keV to moderate fluences the DNA transfer could be induced by ion bombardment of the bacterial cells, while at the same ion energy but to high fluences DNA transfer could not be induced. On the other hand, when the ion energy was medium, about 10–20 keV, the DNA transfer could not be induced by ion bombardment of the cells. The complexity of the experimental results indicated a complex mechanism which should be related to the complex structure of the bacterial E. coli cell envelope. A phase diagram was proposed to interpret different mechanisms involved as functions of the ion energy and fluence.

Mechanisms of ion-bombardment-induced DNA transfer into bacterial E. coli cells

International Nuclear Information System (INIS)

Yu, L.D.; Sangwijit, K.; Prakrajang, K.; Phanchaisri, B.; Thongkumkoon, P.; Thopan, P.; Singkarat, S.; Anuntalabhochai, S.

2014-01-01

Highlights: • Ion bombardment could induce DNA transfer into E. coli cells. • The DNA transfer induction depended on ion energy and fluence. • The mechanism was associated with the bacterial cell envelope structure. • A mechanism phase diagram was proposed to summarize the mechanism. - Abstract: As a useful ion beam biotechnology, ion-bombardment-induced DNA transfer into bacterial Escherichia coli (E. coli) cells has been successfully operated using argon ions. In the process ion bombardment of the bacterial cells modifies the cell envelope materials to favor the exogenous DNA molecules to pass through the envelope to enter the cell. The occurrence of the DNA transfer induction was found ion energy and fluence dependent in a complex manner. At ion energy of a few keV and a few tens of keV to moderate fluences the DNA transfer could be induced by ion bombardment of the bacterial cells, while at the same ion energy but to high fluences DNA transfer could not be induced. On the other hand, when the ion energy was medium, about 10–20 keV, the DNA transfer could not be induced by ion bombardment of the cells. The complexity of the experimental results indicated a complex mechanism which should be related to the complex structure of the bacterial E. coli cell envelope. A phase diagram was proposed to interpret different mechanisms involved as functions of the ion energy and fluence

Hard carbon coated nano-Si/graphite composite as a high performance anode for Li-ion batteries

Energy Technology Data Exchange (ETDEWEB)

Jeong, Sookyung; Li, Xiaolin; Zheng, Jianming; Yan, Pengfei; Cao, Ruiguo; Jung, Hee Joon; Wang, Chong M.; Liu, Jun; Zhang, Jiguang

2016-08-27

With the ever increasing demands on Li-ion batteries with higher energy densities, alternative anode with higher reversible capacity is required to replace the conventional graphite anode. Here, we demonstrate a cost-effective hydrothermal-carbonization approach to prepare the hard carbon coated nano-Si/graphite (HC-nSi/G) composite as a high performance anode for Li-ion batteries. In this hierarchical structured composite, the hard carbon coating layer not only provides an efficient pathway for electron transfer, but also alleviates the volume variation of silicon during charge/discharge processes. The HC-nSi/G composite electrode shows excellent electrochemical performances including a high specific capacity of 878.6 mAh g-1 based on the total weight of composite, good rate performance and a decent cycling stability, which is promising for practical applications.

Embedded Si/Graphene Composite Fabricated by Magnesium-Thermal Reduction as Anode Material for Lithium-Ion Batteries.

Science.gov (United States)

Zhu, Jiangliu; Ren, Yurong; Yang, Bo; Chen, Wenkai; Ding, Jianning

2017-12-16

Embedded Si/graphene composite was fabricated by a novel method, which was in situ generated SiO 2 particles on graphene sheets followed by magnesium-thermal reduction. The tetraethyl orthosilicate (TEOS) and flake graphite was used as original materials. On the one hand, the unique structure of as-obtained composite accommodated the large volume change to some extent. Simultaneously, it enhanced electronic conductivity during Li-ion insertion/extraction. The MR-Si/G composite is used as the anode material for lithium ion batteries, which shows high reversible capacity and ascendant cycling stability reach to 950 mAh·g -1 at a current density of 50 mA·g -1 after 60 cycles. These may be conducive to the further advancement of Si-based composite anode design.

The role of magnetic field fluctuations in nonadiabatic acceleration of ions during dipolarization

Science.gov (United States)

Ono, Y.; Nosé, M.; Christon, S. P.; Lui, A. T. Y.

2009-05-01

We statistically examine changes in the composition of two different ion species, proton and oxygen ions, in the near-Earth plasma sheet (X = -16 R E ˜ -6 R E ) during substorm-associated dipolarization. We use 10 years of energetic (9-212 keV/e) ion data obtained by the suprathermal ion composition spectrometer (STICS) sensor of the energetic particles and ion composition (EPIC) instrument on board the Geotail spacecraft. The results are as follows: (1) Although the percentage increase in the energy density of O+ ions before and after a dipolarization exceeds that of H+ ions in the low-energy range (9-36 keV/e), this property is not evident in the high-energy range (56-212 keV/e); (2) the energy spectrum of H+ and that of O+ become harder after dipolarization in almost all events; and (3) in some events the energy spectrum of O+ becomes harder than that of H+ as reported by previous studies, and, importantly, in other events, the spectrum of H+ becomes harder than that of O+. In order to investigate what mechanism causes these observational results, we focus on magnetic field fluctuations during dipolarization. It is found that the increase of the spectrum slope is positively correlated with the power of waves whose frequencies are close to the gyrofrequency of H+ or O+, respectively (the correlation coefficient is 0.48 for H+ and 0.68 for O+). In conclusion, ions are nonadiabatically accelerated by the electric field induced by the magnetic field fluctuations whose frequencies are close to their gyrofrequencies.

Ion-induced Auger electron spectroscopy: a new detection method for compositional homogeneities of alloyed atoms in silicon

Energy Technology Data Exchange (ETDEWEB)

Hiraki, A [Osaka Univ., Japan; Imura, T; Iwami, M; Kim, S C; Ushita, K; Okamoto, H; Hamakawa, Y

1979-09-01

Auger spectra of Si LMM transitions induced by keV Ar/sup +/ ion bombardment of Si alloy systems have been studied. The spectra observed are composed of two well-defined peaks termed elsewhere the atomic-like and bulk-like peaks, repsectively. A clear correlation has been found between the intensity of the atomic-like peak lying at 88 eV and the content of the foreign atoms alloyed with Si. Experiments were carried out on metallic silicides, or Si alloys with Au, Cu, Pd and Ni, and covalently bonded non-metallic Si alloys of C and H. From these studies, we propose that ion-induced Auger electron spectroscopy might be a useful tool for the determination of alloyed foreign atoms as well as for the study of their compositional homogeneity in binary alloy systems of silicon.

Composition of atmospheric precipitation. I. Sampling technique. Use of ion exchange resins

Energy Technology Data Exchange (ETDEWEB)

Egner, H; Eriksson, E; Emanuelsson, A

1947-01-01

In order to investigate the composition of atmospheric precipitations in Sweden, a technique using ion exchange resins has been developed. The possibilities of nitrate reduction, and ammonia losses, when the precipitation is collected in zinc gauges is stressed. Glass funnels are used, and they are effectively protected from bird droppings. The ion exchange resins so far available are quite serviceable but show some deficiencies as to stability, and activity in alkaline solutions. New resins, which are not yet available, seem to offer definite advantages.

Lifetime of (e+e-) puzzle's composite particle: No valid limits yet

International Nuclear Information System (INIS)

Griffin, J.J.

1993-01-01

Several recent articles assert that the increasingly precise null results of Bhabha scattering imply ''model-independent'' increasing lower bounds upon the lifetime of any neutral particle whose decay is hypothesized to yield the sharp lines of the GSI ''(e + e-) puzzle.'' We discuss here reasons why such conclusions must be considered as artifacts of the assumptions made in the analysis, and not as valid scientific deductions from the data alone. Furthermore, we show that when such data are combined with additional assumptions sufficient to allow an inference about the lifetime, then the conclusion is inevitably dependent explicitly or implicitly upon the model assumed for the particle decay. In addition, we discuss why the limits asserted upon the lifetime of such a particle from the high precision agreement for g e -2 between experiment and theoretical quantum electrodynamics apply only to an elementary particle, but not to a composite particle, and especially not to a leptonic composite. In the end, no valid limits upon the composite particle lifetime seems to exist at present. We also consider, in the context of the general partial width data problem, the additional experimental data which could suffice to sustain a purely empirical limit upon the lifetime, and observe that all of the present data are consistent with a composite particle with a significant amplitude in the four lepton (e + e+e-e-) ''quadronium'' sector. Finally, it is shown that recent preliminary Bhabha inelastic (e + e+γ) data, if confirmed, would imply the crude but genuinely empirical upper bound upon the resonance lifetime of about τ max ∼2x10 -11 sec≥τ

Media ion composition controls regulatory and virulence response of Salmonella in spaceflight.

Directory of Open Access Journals (Sweden)

James W Wilson

Full Text Available The spaceflight environment is relevant to conditions encountered by pathogens during the course of infection and induces novel changes in microbial pathogenesis not observed using conventional methods. It is unclear how microbial cells sense spaceflight-associated changes to their growth environment and orchestrate corresponding changes in molecular and physiological phenotypes relevant to the infection process. Here we report that spaceflight-induced increases in Salmonella virulence are regulated by media ion composition, and that phosphate ion is sufficient to alter related pathogenesis responses in a spaceflight analogue model. Using whole genome microarray and proteomic analyses from two independent Space Shuttle missions, we identified evolutionarily conserved molecular pathways in Salmonella that respond to spaceflight under all media compositions tested. Identification of conserved regulatory paradigms opens new avenues to control microbial responses during the infection process and holds promise to provide an improved understanding of human health and disease on Earth.

Electron capture by multicharged ions at eV energies

International Nuclear Information System (INIS)

Havener, C.C.; Huq, M.S.; Meyer, F.W.; Phaneuf, R.A.

1988-01-01

A multicharged ion-atom merged-beams apparatus has been used in conjunction with the ORNL-ECR ion source to measure accurate absolute electron-capture cross sections in the energy range from below 1 eV/amu to 1500 eV/amu. Measurements for N/sup 3+,4+,5+/ /plus/ H(D) collisions indicate good agreement with available theoretical calculations. However, measurements with O 5+ /plus/ H(D) show an unexpected low-energy behavior which may be attributable to the ion-induced-dipole attraction between the reactants. Scaled Landau-Zener calculations presented here identify a transfer plus excitation channel which has the correct energy dependence at low energies. This finding suggest the need for a comprehensive coupled channel calculation which would include such product states. 25 refs., 8 figs

Composition of hot ions /0.1-16 keV/e/ as observed by the GEOS and ISEE mass spectrometers and inferences for the origin and circulation of magnetospheric plasmas

Science.gov (United States)

Balsiger, H.

1981-01-01

The composition of hot magnetospheric plasma through different regions of the magnetosphere is described on the basis of mass spectrometer measurements by the GEOS 1, GEOS 2, and ISEE-1 spacecraft. Coordinated composition measurements on the different spacecraft also provide information on the spatial and temporal characteristics of the plasma during storms. Data on ion origins are also provided.

Study of sporadic E layers based on GPS radio occultation measurements and digisonde data over the Brazilian region

Science.gov (United States)

Resende, Laysa C. A.; Arras, Christina; Batista, Inez S.; Denardini, Clezio M.; Bertollotto, Thainá O.; Moro, Juliano

2018-04-01

This work presents new results about sporadic E-layers (Es layers) using GPS (global positioning system) radio occultation (RO) measurements obtained from the FORMOSAT-3/COSMIC satellites and digisonde data. The RO profiles are used to study the Es layer occurrence as well as its intensity of the signal-to-noise ratio (SNR) of the 50 Hz GPS L1 signal. The methodology was applied to identify the Es layer on RO measurements over Cachoeira Paulista, a low-latitude station in the Brazilian region, in which the Es layer development is not driven tidal winds only as it is at middle latitudes. The coincident events were analyzed using the RO technique and ionosonde observations during the year 2014 to 2016. We used the electron density obtained using the blanketing frequency parameter (fbEs) and the Es layer height (h'Es) acquired from the ionograms to validate the satellite measurements. The comparative results show that the Es layer characteristics extracted from the RO measurements are in good agreement with the Es layer parameters from the digisonde.

Sporadic simple groups and quotient singularities

International Nuclear Information System (INIS)

Cheltsov, I A; Shramov, C A

2013-01-01

We show that if a faithful irreducible representation of a central extension of a sporadic simple group with centre contained in the commutator subgroup gives rise to an exceptional (resp. weakly exceptional but not exceptional) quotient singularity, then that simple group is the Hall-Janko group (resp. the Suzuki group)

Deletion and reduced expression of the Fanconi anemia FANCA gene in sporadic acute myeloid leukemia.

Science.gov (United States)

Tischkowitz, M D; Morgan, N V; Grimwade, D; Eddy, C; Ball, S; Vorechovsky, I; Langabeer, S; Stöger, R; Hodgson, S V; Mathew, C G

2004-03-01

Fanconi anemia (FA) is an autosomal recessive chromosomal instability disorder caused by mutations in one of seven known genes (FANCA,C,D2,E,F,G and BRCA2). Mutations in the FANCA gene are the most prevalent, accounting for two-thirds of FA cases. Affected individuals have greatly increased risks of acute myeloid leukemia (AML). This raises the question as to whether inherited or acquired mutations in FA genes might be involved in the development of sporadic AML. Quantitative fluorescent PCR was used to screen archival DNA from sporadic AML cases for FANCA deletions, which account for 40% of FANCA mutations in FA homozygotes. Four heterozygous deletions were found in 101 samples screened, which is 35-fold higher than the expected population frequency for germline FANCA deletions (PFANCA in the AML samples with FANCA deletions did not detect mutations in the second allele and there was no evidence of epigenetic silencing by hypermethylation. However, real-time quantitative PCR analysis in these samples showed reduced expression of FANCA compared to nondeleted AML samples and to controls. These findings suggest that gene deletions and reduced expression of FANCA may be involved in the promotion of genetic instability in a subset of cases of sporadic AML.

Cassini CAPS Identification of Pickup Ion Compositions at Rhea

Science.gov (United States)

Desai, R. T.; Taylor, S. A.; Regoli, L. H.; Coates, A. J.; Nordheim, T. A.; Cordiner, M. A.; Teolis, B. D.; Thomsen, M. F.; Johnson, R. E.; Jones, G. H.; Cowee, M. M.; Waite, J. H.

2018-02-01

Saturn's largest icy moon, Rhea, hosts a tenuous surface-sputtered exosphere composed primarily of molecular oxygen and carbon dioxide. In this Letter, we examine Cassini Plasma Spectrometer velocity space distributions near Rhea and confirm that Cassini detected nongyrotropic fluxes of outflowing CO2+ during both the R1 and R1.5 encounters. Accounting for this nongyrotropy, we show that these possess comparable along-track densities of ˜2 × 10-3 cm-3. Negatively charged pickup ions, also detected during R1, are surprisingly shown as consistent with mass 26 ± 3 u which we suggest are carbon-based compounds, such as CN-, C2H-, C2-, or HCO-, sputtered from carbonaceous material on the moon's surface. The negative ions are calculated to possess along-track densities of ˜5 × 10-4 cm-3 and are suggested to derive from exogenic compounds, a finding consistent with the existence of Rhea's dynamic CO2 exosphere and surprisingly low O2 sputtering yields. These pickup ions provide important context for understanding the exospheric and surface ice composition of Rhea and of other icy moons which exhibit similar characteristics.

Method for the elucidation of the elemental composition of low molecular mass chemicals using exact masses of product ions and neutral losses: application to environmental chemicals measured by liquid chromatography with hybrid quadrupole/time-of-flight mass spectrometry.

Science.gov (United States)

Suzuki, Shigeru; Ishii, Tetsuko; Yasuhara, Akio; Sakai, Shinichi

2005-01-01

A method for elucidating the elemental compositions of low molecular weight chemicals, based primarily on mass measurements made using liquid chromatography (LC) with time-of-flight mass spectrometry (TOFMS) and quadrupole/time-of-flight mass spectrometry (LC/QTOFMS), was developed and tested for 113 chemicals of environmental interest with molecular masses up to approximately 400 Da. As the algorithm incorporating the method is not affected by differences in the instrument used, or by the ionization method and other ionization conditions, the method is useful not only for LC/TOFMS, but also for all kinds of mass spectra measured with higher accuracy and precision (uncertainties of a few mDa) employing all ionization methods and on-line separation techniques. The method involves calculating candidate compositions for intact ionized molecules (ionized forms of the sample molecule that have lost or gained no more than a proton, i.e., [M+H](+) or [M-H](-)) as well as for fragment ions and corresponding neutral losses, and eliminating those atomic compositions for the molecules that are inconsistent with the corresponding candidate compositions of fragment ions and neutral losses. Candidate compositions were calculated for the measured masses of the intact ionized molecules and of the fragment ions and corresponding neutral losses, using mass uncertainties of 2 and 5 mDa, respectively. Compositions proposed for the ionized molecule that did not correspond to the sum of the compositions of a candidate fragment ion and its corresponding neutral loss were discarded. One, 2-5, 6-10, 11-20, and >20 candidate compositions were found for 65%, 39%, 1%, 1%, and 0%, respectively, for the 124 ionized molecules formed from the 113 chemicals tested (both positive and negative ions were obtained from 11 of the chemicals). However, no candidate composition was found for 2% of the test cases (i.e., 3 chemicals), for each of which the measured mass of one of the product ions was in

Adsorption Effectivity Test of Andisols Clay-Zeolite (ACZ) Composite as Chromium Hexavalent (Cr(VI)) Ion Adsorbent

Science.gov (United States)

Pranoto; Masykur, A.; Nugroho, Y. A.

2018-03-01

Adsorption of chromium hexavalent (Cr(VI)) ion in aqueous solution was investigated. This research was purposed to study the influence of the composition of ACZ, temperature activation, and contact time against adsorption capacity of Cr(VI) ion in aqueous solution. Determination of adsorption effectivity using several parameter such as composition variation of ACZ, contact time, pH, activation temperature, and concentration. In this research, andisol clay and zeolite has been activated with NaOH 3 M and 1 M, respectively. Temperature variation used 100, 200, and 400°C. While composition variation ACZ used 0:100, 25:75, 50:50, 75:25, 100:0. The pH variation was used 2 – 6 and concentration variation using 2, 4, 6, 8, 10, and 12 ppm. Characterization in this research used such as UV-Vis, Surface Area Analyzer (SAA) and Acidity Analysis. Result of this research is known that optimum composition of ACZ was 50:50 with calcination temperature 100°C. Optimum adsorption of Cr(VI) at pH 4 with removal percentage 76.10 % with initial concentration 2 ppm and adsorption capacity is 0.16 mg/g. Adsorption isotherm following freundlich isotherm with value Kf = 0.17 mg/g and value n is 0.963. Based on results, ACZ composite can be used as Cr(VI) ion adsorbents in aqueous solutions.

Dependence of secondary ion emission current on the composition of beryllium-nickel alloys

International Nuclear Information System (INIS)

Pistryak, V.M.; Kozlov, V.F.; Tikhinskij, G.F.; Fogel', Ya.M.

1976-01-01

The dependence is studied of the secondary ions emission current on the composition of beryllium-nickel alloys. It is established that appearance of intermetallide phases in the Be-Ni alloys has no effect on the linear character of the secondary ions Ni + and Be + of emission current. The phase transformation from the solid solution to the compound Ni 5 Be 21 with a change in the alloys concentration is fixed by appearance of the secondary ion NiBe + emission. The limited solubility of nickel in solid beryllium at a temperature close to room temperature is determined to be equal to 1.3+-0.27 at%

Screening of hypoxia-inducible genes in sporadic ALS.

LENUS (Irish Health Repository)

Cronin, Simon

2008-10-01

Genetic variations in two hypoxia-inducible angiogenic genes, VEGF and ANG, have been linked with sporadic amyotrophic lateral sclerosis (SALS). Common variations in these genes may reduce the levels or functioning of their products. VEGF and ANG belong to a larger group of angiogenic genes that are up-regulated under hypoxic conditions. We hypothesized that common genetic variation across other members of this group may also predispose to sporadic ALS. To screen other hypoxia-inducible angiogenic genes for association with SALS, we selected 112 tagging single nucleotide polymorphisms (tgSNPs) that captured the common genetic variation across 16 VEGF-like and eight ANG-like hypoxia-inducible genes. Screening for association was performed in 270 Irish individuals with typical SALS and 272 ethnically matched unrelated controls. SNPs showing association in the Irish phase were genotyped in a replication sample of 281 Swedish sporadic ALS patients and 286 Swedish controls. Seven markers showed association in the Irish. The one modest replication signal observed in the Swedish replication sample, at rs3801158 in the gene inhibin beta A, was for the opposite allele vs. the Irish cohort. We failed to detect association of common variation across 24 candidate hypoxia-inducible angiogenic genes with SALS.

Ion release from a composite resin after exposure to different 10% carbamide peroxide bleaching agents

Directory of Open Access Journals (Sweden)

Renata Plá Rizzolo Bueno

2012-06-01

Full Text Available OBJECTIVE: This in vitro study evaluated the influence of two 10% carbamide peroxide bleaching agents - a commercial product (Opalescence PF; Ultradent Products, Inc. and a bleaching agent prepared in a compounding pharmacy - on the chemical degradation of a light-activated composite resin by determining its release of ions before and after exposure to the agents. MATERIAL AND METHODS: Thirty composite resin (Filtek Z250; 3M/ESPE samples were divided into three groups: group I (exposed to Opalescence PF commercial bleaching agent, group II (exposed to a compounded bleaching agent and group III (control - Milli-Q water. After 14 days of exposure, with a protocol of 8 h of daily exposure to the bleaching agents and 16 h of immersion in Milli-Q water, the analysis of ion release was carried out using a HP 8453 spectrophotometer. The values were analyzed statistically by ANOVA, Tukey's test and the paired t-tests. The significance level was set at 5%. RESULTS: After 14 days of the experiment, statistically significant difference was found between group II and groups I and III, with greater ion release from the composite resin in group II. CONCLUSIONS: The compounded bleaching agent had a more aggressive effect on the composite resin after 14 days of exposure than the commercial product and the control (no bleaching.

Interweaved Si@C/CNTs and CNFs composites as anode materials for Li-ion batteries

Energy Technology Data Exchange (ETDEWEB)

Zhang, Miao [School of Physics and Telecommunication Engineering, South China Normal University, Guangzhou 510006 (China); Hou, Xianhua, E-mail: houxh@scnu.edu.cn [School of Physics and Telecommunication Engineering, South China Normal University, Guangzhou 510006 (China); Engineering Research Center of Materials and Technology for Electrochemical Energy Storage Ministry of Education, Guangzhou 510006 (China); Wang, Jie; Li, Min [School of Physics and Telecommunication Engineering, South China Normal University, Guangzhou 510006 (China); Hu, Shejun [School of Physics and Telecommunication Engineering, South China Normal University, Guangzhou 510006 (China); Engineering Research Center of Materials and Technology for Electrochemical Energy Storage Ministry of Education, Guangzhou 510006 (China); Shao, Zongping [Nanjing University of Technology, College of Chemistry and Chemical Engineering, Nanjing 210009 (China); Liu, Xiang [Institute of Advanced Materials, Nanjing University of Technology, Nanjing 210009 (China)

2014-03-05

Graphical abstract: In summary, a serious of high-energy wet ball milling, closed spray drying and subsequent chemical vapor deposition methods were introduced successfully to fabricated novel Si@C/CNTs and CNFs composites with carbon nanotubes and carbon nanofibres interweaved with carbon coated silicon spherical composites as superior anodes in lithium-ion batteries. The core-shell structure of Si@C composites can accommodate the volume change of electrode during charge and discharge. Meanwhile, the citric acid pyrolyzed carbon was coated on the surface of the silicon perfectly and constructs the connection network of nano silicon particles. Moreover, the carbon nanotubes and carbon nanofibres, which is interweaved with nano-silicon, also allows high electrical conductivity, improved solid–electrolyte interface formation and structural integrity. Compared with pure silicon and Si@C composites, the novel Si@C/CNTs and CNFs composites had the best combination of reversible capacity and cycleablity, and this anode materials exhibited excellent electrochemical performance. The Si/C composite had a fairly high initial discharge capacity of 2168.7 mA h g{sup −1} with an efficiency of 73%, and the discharge capacity of the 50th cycle maintained surprisingly of 1194.9 mA h g{sup −1}. Meanwhile, spray drying and chemical vapor deposition are environmentally friendly, economical, and relatively high-yield method for the production of the Si@C/CNTs and CNFs composites in large quantities. Consequently, the novel Si@C/CNTs and CNFs composite electrodes may be a potential alternative to graphite for high energy density lithium ion batteries. Highlights: • The core/shell structured silicon/carbon composites were prepared by a facile way. • The as-prepared Si@C/CNTs and CNFs composites shows excellent electrochemical performance. • The preparation method has mild experiment conditions and high production rate. • The structure benefited electronic transfer and

Copper nanofiber-networked cobalt oxide composites for high performance Li-ion batteries

Directory of Open Access Journals (Sweden)

Shim Hee-Sang

2011-01-01

Full Text Available Abstract We prepared a composite electrode structure consisting of copper nanofiber-networked cobalt oxide (CuNFs@CoO x . The copper nanofibers (CuNFs were fabricated on a substrate with formation of a network structure, which may have potential for improving electron percolation and retarding film deformation during the discharging/charging process over the electroactive cobalt oxide. Compared to bare CoO x thin-film (CoO x TF electrodes, the CuNFs@CoO x electrodes exhibited a significant enhancement of rate performance by at least six-fold at an input current density of 3C-rate. Such enhanced Li-ion storage performance may be associated with modified electrode structure at the nanoscale, improved charge transfer, and facile stress relaxation from the embedded CuNF network. Consequently, the CuNFs@CoO x composite structure demonstrated here can be used as a promising high-performance electrode for Li-ion batteries.

Preparation of Nafion 117™-SnO₂ Composite Membranes using an Ion-Exchange Method

DEFF Research Database (Denmark)

Nørgaard, Casper Frydendal; Nielsen, Ulla Gro; Skou, Eivind Morten

2012-01-01

Nafion 117™-SnO2 composite membranes were prepared by in-situ particle formation using an ion-exchange method. SnO2 was incorporated into Nafion 117ä membranes by ion-exchange in solutions of SnCl2 ∙2 H2O in methanol, followed by oxidation to SnO2 in air. By adjustment of the concentration of SnCl2...... ∙ 2 H2O used in the ion-exchange step, compositions ranging from 2 to 8 wt% SnO2 with SnO2 homogeneously distributed as nanoparticles were obtained. The prepared nanocomposite membranes were characterized by powder XRD, 119Sn MAS NMR spectroscopy, electrochemical impedance spectroscopy, water uptake...

Early Detection of Sporadic Pancreatic Cancer

Science.gov (United States)

Kenner, Barbara J.; Chari, Suresh T.; Cleeter, Deborah F.; Go, Vay Liang W.

2015-01-01

Abstract Innovation leading to significant advances in research and subsequent translation to clinical practice is urgently necessary in early detection of sporadic pancreatic cancer. Addressing this need, the Early Detection of Sporadic Pancreatic Cancer Summit Conference was conducted by Kenner Family Research Fund in conjunction with the 2014 American Pancreatic Association and Japan Pancreas Society Meeting. International interdisciplinary scientific representatives engaged in strategic facilitated conversations based on distinct areas of inquiry: Case for Early Detection: Definitions, Detection, Survival, and Challenges; Biomarkers for Early Detection; Imaging; and Collaborative Studies. Ideas generated from the summit have led to the development of a Strategic Map for Innovation built upon 3 components: formation of an international collaborative effort, design of an actionable strategic plan, and implementation of operational standards, research priorities, and first-phase initiatives. Through invested and committed efforts of leading researchers and institutions, philanthropic partners, government agencies, and supportive business entities, this endeavor will change the future of the field and consequently the survival rate of those diagnosed with pancreatic cancer. PMID:25938853

Magnetic resonance spectroscopic abnormalities in sporadic and variant Creutzfeldt-Jakob disease

International Nuclear Information System (INIS)

Pandya, H.G.; Coley, S.C.; Wilkinson, I.D.; Griffiths, P.D.

2003-01-01

AIM: To study the proton MR spectroscopic findings in Creutzfeldt-Jakob disease (CJD) (sporadic and variant). MATERIALS AND METHODS: MR imaging and proton MR spectra were acquired in two patients with sporadic CJD (biopsy proven) and one patient with variant CJD. RESULTS: The two patients with sporadic CJD demonstrated MR signal change within the basal ganglia and thalami and reduced N-acetylaspartate (NAA):creatine ratios. The patient with variant CJD showed characteristic signal change within the pulvinar of the thalami and a markedly reduced N-acetylaspartate:creatine ratio. CONCLUSION: All three patients with CJD demonstrated evidence of reduced N-acetylaspartate: creatine ratios on MR spectroscopy. These changes imply that neuronal loss and/or dysfunction is a consistent finding in established CJD. Pandya H. G., et al (2003) Clinical Radiology58, 148--153

Magnetic resonance spectroscopic abnormalities in sporadic and variant Creutzfeldt-Jakob disease

Energy Technology Data Exchange (ETDEWEB)

Pandya, H.G.; Coley, S.C.; Wilkinson, I.D.; Griffiths, P.D

2003-02-01

AIM: To study the proton MR spectroscopic findings in Creutzfeldt-Jakob disease (CJD) (sporadic and variant). MATERIALS AND METHODS: MR imaging and proton MR spectra were acquired in two patients with sporadic CJD (biopsy proven) and one patient with variant CJD. RESULTS: The two patients with sporadic CJD demonstrated MR signal change within the basal ganglia and thalami and reduced N-acetylaspartate (NAA):creatine ratios. The patient with variant CJD showed characteristic signal change within the pulvinar of the thalami and a markedly reduced N-acetylaspartate:creatine ratio. CONCLUSION: All three patients with CJD demonstrated evidence of reduced N-acetylaspartate: creatine ratios on MR spectroscopy. These changes imply that neuronal loss and/or dysfunction is a consistent finding in established CJD. Pandya H. G., et al (2003) Clinical Radiology58, 148--153.

Cervical dystonia: about familial and sporadic cases in 88 patients

Directory of Open Access Journals (Sweden)

Carlos Henrique F. Camargo

2014-02-01

Full Text Available Cervical dystonia (CD affects the musculature of the neck in a focal way or associated to other parts of the body. The aim of this study was to identify clinical differences between patients with dystonia patients without family history and with family history (sporadic. Eighty-eight patients with CD were recruited in a Movement Disorders Clinic between June of 2008 and June of 2009. Only patients with no etiological diagnosis were accepted for analysis. The age of onset of symptoms was later in patients with focal and segmental dystonia than in patients with generalized dystonia (p<0.001. The severity of symptoms was higher in patients with sporadic dystonia than in familial patients (p<0.01. Generalized cases were more severe in patients with a family history (p<0.01. Sporadic patients had higher levels of pain than familial cases (p<0.05. We expect soon to present the results of genetic analyzes of these patients.

Electrondynamics of the auroral E region

International Nuclear Information System (INIS)

Kirkwood, Sheila.

1990-10-01

This study concentrates on the signatures of the interaction process seen closest to the Earth - i.e. in the region where the visible aurora is produced. A number of experimental investigations are presented which look at details of the dynamics and electrodynamics of auroral ionisation features in the ionospheric E region. The studies are based primarily on measurement with the EISCAT UHF incoherent scatter radar which is located in northern Scandinavia. Initial calibration of the radar, and some measurements of the properties of the background atmosphere are described first. These are a necessary basis for the detailed studies which follow, which are of two aspects of auroral electrodynamics - substorms and aurorally-associated sporadic E layers. For the substorm studies, all-sky camera observations of the aurora over Scandinavia and ultra-violet images from the Viking satellite are used to identify the auroral forms corresponding to EISCAT measurements. This allows the determination of representative conductivities for the different auroral features which are characteristic of the substorm development. These conductivities are an important input for modelling studies of the electric current systems and have not previously been measured directly. Particle measurements from the Viking satellite are used together with EISCAT to determine the origin of the particles precipitated into the ionosphere during the energy-storage phase prior to the substorm. The sporadic E layers studies address the question of how ion layers and associated neutral sodium layers can be produced by some process which is common in association with auroral activity. Two candidates are considered - gravity waves and electric fields. (author)

Electrodeposited Germanium/Carbon Composite as an Anode Material for Lithium Ion Batteries

International Nuclear Information System (INIS)

Kim, Sang-Wan; Ngo, Duc Tung; Heo, Jaeyeong; Park, Choong-Nyeon; Park, Chan-Jin

2017-01-01

Highlights: • Electrodeposition was applied for the synthesis of Ge/C composite. • High coulombic efficiency of ∼85% in the first cycle was attained for Ge/C composite. • Full cell of Ge/C-LiCoO 2 exhibits excellent electrochemical performance, without pre-lithiation of Ge/C. - Abstract: We demonstrate the synthesis of nano Ge/C composite using a facile and cost-effective electrochemical deposition method, and its application as an anode material in Li-ion batteries. Nano Ge/C composite is electrodeposited directly on Cu foil in ethylene glycol containing GeCl 4 and carbon black. The Ge particles with an average size of ∼20 nm are uniformly covered with carbon. Compared with the pure Ge electrode, the Ge/C electrode exhibits a higher first reversible capacity of 1224 mA g −1 , and maintains a capacity of 1095 mAh g −1 at 0.1C over 50 cycles. Even at the high rate of 2C, the capacity of the Ge/C electrode is still high at 972 mAh g −1 . The presence of carbon black and pores in the Ge/C electrode improves the conductivity of the electrode, and mitigates the stress inside the electrode by supplying buffer volume, leading to the enhanced electrochemical characteristics of the electrode. Further, the full Li-ion cell composed of Ge/C anode and LiCoO 2 cathode exhibits good cyclability, rate capability, and coulombic efficiency.

Nanostructured Si/TiC composite anode for Li-ion batteries

International Nuclear Information System (INIS)

Zeng, Z.Y.; Tu, J.P.; Yang, Y.Z.; Xiang, J.Y.; Huang, X.H.; Mao, F.; Ma, M.

2008-01-01

Si/TiC nanocomposite anode was synthesized by a surface sol-gel method in combination with a following heat-treatment process. Through this process, nanosized Si was homogeneously distributed in a titanium carbide matrix. The electrochemically less active TiC working as a buffer matrix successfully prevented Si from cracking/crumbling during the charging/discharging process. The interspaces in the Si/TiC nanocomposite could offer convenient channels for Li ions to react with active Si. The Si/TiC composite exhibited a reversible charge/discharge capacity of about 1000 mAh g -1 with average discharge capacity fading of 1.8 mAh g -1 (0.18%) from 2nd to 100th cycle, indicating its excellent cyclability when used as anode materials for lithium-ion batteries

New application of intelligent agents in sporadic amyotrophic lateral sclerosis identifies unexpected specific genetic background

Directory of Open Access Journals (Sweden)

Marocchi Alessandro

2008-05-01

Full Text Available Abstract Background Few genetic factors predisposing to the sporadic form of amyotrophic lateral sclerosis (ALS have been identified, but the pathology itself seems to be a true multifactorial disease in which complex interactions between environmental and genetic susceptibility factors take place. The purpose of this study was to approach genetic data with an innovative statistical method such as artificial neural networks to identify a possible genetic background predisposing to the disease. A DNA multiarray panel was applied to genotype more than 60 polymorphisms within 35 genes selected from pathways of lipid and homocysteine metabolism, regulation of blood pressure, coagulation, inflammation, cellular adhesion and matrix integrity, in 54 sporadic ALS patients and 208 controls. Advanced intelligent systems based on novel coupling of artificial neural networks and evolutionary algorithms have been applied. The results obtained have been compared with those derived from the use of standard neural networks and classical statistical analysis Results Advanced intelligent systems based on novel coupling of artificial neural networks and evolutionary algorithms have been applied. The results obtained have been compared with those derived from the use of standard neural networks and classical statistical analysis. An unexpected discovery of a strong genetic background in sporadic ALS using a DNA multiarray panel and analytical processing of the data with advanced artificial neural networks was found. The predictive accuracy obtained with Linear Discriminant Analysis and Standard Artificial Neural Networks ranged from 70% to 79% (average 75.31% and from 69.1 to 86.2% (average 76.6% respectively. The corresponding value obtained with Advanced Intelligent Systems reached an average of 96.0% (range 94.4 to 97.6%. This latter approach allowed the identification of seven genetic variants essential to differentiate cases from controls: apolipoprotein E arg

New application of intelligent agents in sporadic amyotrophic lateral sclerosis identifies unexpected specific genetic background.

Science.gov (United States)

Penco, Silvana; Buscema, Massimo; Patrosso, Maria Cristina; Marocchi, Alessandro; Grossi, Enzo

2008-05-30

Few genetic factors predisposing to the sporadic form of amyotrophic lateral sclerosis (ALS) have been identified, but the pathology itself seems to be a true multifactorial disease in which complex interactions between environmental and genetic susceptibility factors take place. The purpose of this study was to approach genetic data with an innovative statistical method such as artificial neural networks to identify a possible genetic background predisposing to the disease. A DNA multiarray panel was applied to genotype more than 60 polymorphisms within 35 genes selected from pathways of lipid and homocysteine metabolism, regulation of blood pressure, coagulation, inflammation, cellular adhesion and matrix integrity, in 54 sporadic ALS patients and 208 controls. Advanced intelligent systems based on novel coupling of artificial neural networks and evolutionary algorithms have been applied. The results obtained have been compared with those derived from the use of standard neural networks and classical statistical analysis Advanced intelligent systems based on novel coupling of artificial neural networks and evolutionary algorithms have been applied. The results obtained have been compared with those derived from the use of standard neural networks and classical statistical analysis. An unexpected discovery of a strong genetic background in sporadic ALS using a DNA multiarray panel and analytical processing of the data with advanced artificial neural networks was found. The predictive accuracy obtained with Linear Discriminant Analysis and Standard Artificial Neural Networks ranged from 70% to 79% (average 75.31%) and from 69.1 to 86.2% (average 76.6%) respectively. The corresponding value obtained with Advanced Intelligent Systems reached an average of 96.0% (range 94.4 to 97.6%). This latter approach allowed the identification of seven genetic variants essential to differentiate cases from controls: apolipoprotein E arg158cys; hepatic lipase -480 C/T; endothelial

Genetic Relatedness among Nontypeable Pneumococci Implicated in Sporadic Cases of Conjunctivitis

OpenAIRE

Barker, Jason H.; Musher, Daniel M.; Silberman, Ronald; Phan, Hoang M.; Watson, David A.

1999-01-01

Nontypeable Streptococcus pneumoniae is a common cause of epidemic conjunctivitis. A previous molecular fingerprinting study identified a clone of nontypeable pneumococcus that was responsible for a recent outbreak of conjunctivitis. In the present study, we examined the extent to which pneumococci that cause sporadic cases of conjunctivitis are related to this epidemic strain. Using arbitrarily primed BOX-PCR, we have determined that, of 10 nontypeable pneumococci causing sporadic conjunctiv...

Difference in aneurysm characteristics between patients with familial and sporadic aneurysmal subarachnoid haemorrhage

NARCIS (Netherlands)

Mensing, Liselore A.; Rinkel, Gabriel J E; Vlak, Monique H M; Van Der Schaaf, Irene C.; Ruigrok, Ynte M.

2016-01-01

Object Patients with familial intracranial aneurysms (IA) have a higher risk of rupture than patients with sporadic IA. We compared geometric and morphological risk factors for aneurysmal rupture between patients with familial and sporadic aneurysmal subarachnoid hemorrhage (aSAH) to analyse if

On the extension of (e,2e) theory to coincidence studies of ion-atom collisions

International Nuclear Information System (INIS)

Godunov, A.L.; Kampp, Marco; Sulik, B.; Walters, H.R.J.; Whelan, Colm T.

2007-01-01

The extension of (e,2e) theory to the coincidence studies of ion-atom collisions is considered. The simultaneous ionization of projectile and target is discussed and results are presented for transfer ionization

Observations of peculiar sporadic sodium structures and their relation with wind variations

Science.gov (United States)

Sridharan, S.; Prasanth, P. Vishnu; Kumar, Y. Bhavani; Ramkumar, Geetha; Sathishkumar, S.; Raghunath, K.

2009-04-01

Resonance lidar observations of sodium density in the upper mesosphere region over Gadanki (13.5°N, 79.2°E) rarely show complex structures with rapid enhancements of sodium density, completely different from normal sporadic sodium structures. The hourly averaged meteor radar zonal winds over Trivandrum (8.5°N, 76.5°E) show an eastward shear with altitude during the nights, when these events are formed. As suggested by Kane et al. [2001. Joint observations of sodium enhancements and field-aligned ionospheric irregularities. Geophysical Research Letters 28, 1375-1378], our observations show that the complex structures may be formed due to Kelvin-Helmholtz instability, which can occur in the region of strong wind shear.

Biomass carbon composited FeS2 as cathode materials for high-rate rechargeable lithium-ion battery

Science.gov (United States)

Xu, Xin; Meng, Zhen; Zhu, Xueling; Zhang, Shunlong; Han, Wei-Qiang

2018-03-01

Pyrite FeS2 has long been used as commercial primary lithium batteries at room temperature. To achieve rechargeable FeS2 battery, biomass-carbon@FeS2 composites are prepared using green and renewable auricularia auricula as carbon source through the process of carbonization and sulfuration. The auricularia auricula has strong swelling characteristics to absorb aqueous solution which can effectively absorb Fe ions into its body. FeS2 homogeneously distributed in biomass carbon matrix performs high electronic and ionic conductivity. The specific capacity of biomass-carbon@FeS2 composites remains 850 mAh g-1 after 80 cycles at 0.5C and 700 mAh g-1 at the rate of 2C after 150 cycles. Biomass-carbon@FeS2 composites exhibit high-rate capacity in lithium-ion battery.

Molecular pathogenesis of sporadic prion diseases in man

Science.gov (United States)

Safar, Jiri G.

2012-01-01

The yeast, fungal and mammalian prions determine heritable and infectious traits that are encoded in alternative conformations of proteins. They cause lethal sporadic, familial and infectious neurodegenerative conditions in man, including Creutzfeldt-Jakob disease (CJD), Gerstmann-Sträussler-Scheinker syndrome (GSS), kuru, sporadic fatal insomnia (SFI) and likely variable protease-sensitive prionopathy (VPSPr). The most prevalent of human prion diseases is sporadic (s)CJD. Recent advances in amplification and detection of prions led to considerable optimism that early and possibly preclinical diagnosis and therapy might become a reality. Although several drugs have already been tested in small numbers of sCJD patients, there is no clear evidence of any agent’s efficacy. Therefore, it remains crucial to determine the full spectrum of sCJD prion strains and the conformational features in the pathogenic human prion protein governing replication of sCJD prions. Research in this direction is essential for the rational development of diagnostic as well as therapeutic strategies. Moreover, there is growing recognition that fundamental processes involved in human prion propagation – intercellular induction of protein misfolding and seeded aggregation of misfolded host proteins – are of far wider significance. This insight leads to new avenues of research in the ever-widening spectrum of age-related human neurodegenerative diseases that are caused by protein misfolding and that pose a major challenge for healthcare. PMID:22421210

Mechanical characterization and ion release of bioactive dental composites containing calcium phosphate particles.

Science.gov (United States)

Natale, Livia C; Rodrigues, Marcela C; Alania, Yvette; Chiari, Marina D S; Boaro, Leticia C C; Cotrim, Marycel; Vega, Oscar; Braga, Roberto R

2018-08-01

to verify the effect of the addition of dicalcium phosphate dihydrate (DCPD) particles functionalized with di- or triethylene glycol dimethacrylate (DEGDMA or TEGDMA) on the degree of conversion (DC), post-gel shrinkage (PS), mechanical properties, and ion release of experimental composites. Four composites were prepared containing a BisGMA/TEGDMA matrix and 60 vol% of fillers. The positive control contained only barium glass fillers, while in the other composites 15 vol% of the barium was replaced by DCPD. Besides the functionalized particles, non-functionalized DCPD was also tested. DC after 24 h (n = 3) was determined by FTIR spectroscopy. The strain gage method was used to obtain PS 5 min after photoactivation (n = 5). Flexural strength and modulus (n = 10) were calculated based on the biaxial flexural test results, after specimen storage for 24 h or 60 days in water. The same storage times were used for fracture toughness testing (FT, n = 10). Calcium and phosphate release up to 60 days was quantified by ICP-OES (n = 3). Data were analyzed by ANOVA/Tukey test (alpha: 5%). Composites containing functionalized DCPD presented higher DC than the control (p composites (p composite with DEGDMA-functionalized DCPD presented fracture strength similar to the control, while for flexural modulus only the composite with TEGDMA-functionalized particles was lower than the control (p composites containing DCPD was higher than the control after 60 days (p composite with non-functionalized DCPD at 15 days and no significant reductions were observed for composites with functionalized DCPD during the observation period (p composites, phosphate release was higher at 15 days than in the subsequent periods, and no difference among them was recorded at 45 and 60 days (p composite with DEGDMA-functionalized particles was the only material with strength similar to the control after 60 days in water; however, it also presented the highest

Compositional changes of human hair melanin resulting from bleach treatment investigated by nanoscale secondary ion mass spectrometry.

Science.gov (United States)

Kojima, Toru; Yamada, Hiromi; Isobe, Mitsuru; Yamamoto, Toshihiko; Takeuchi, Miyuki; Aoki, Dan; Matsushita, Yasuyuki; Fukushima, Kazuhiko

2014-11-01

It is important to understand the influence of bleach treatment on human hair because it is one of the most important chemical treatments in hair cosmetic processes. A comparison of the elemental composition of melanin between virgin hair and bleached hair would provide important information about the structural changes of melanin. To investigate the elemental composition of melanin granules in virgin black hair and bleached hair, these hair cross-sections are analyzed by using a nanoscale secondary ion mass spectrometry (NanoSIMS). The virgin black hair and bleached hair samples were embedded in resin and smooth hair cross-sections were obtained using an ultramicrotome. NanoSIMS measurements were performed using a Cs(+) primary ion beam to detect negative secondary ions. More intensive (16) O(-) ions were detected from the melanin granules of bleached hair than from those of virgin black hair in NanoSIMS (16) O(-) ion image. In addition, it was indicated that (16) O(-) ion intensity and (16) O(-) /(12) C(14) N(-) ion intensity ratio of melanin granules in bleached hair were higher than those in virgin black hair. Nanoscale secondary ion mass spectrometry analysis of the cross-sections of virgin black hair and bleached hair indicated that the oxygen content in melanin granules was increased by bleach treatment. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Solar Ion Processing of Major Element Surface Compositions of Mature Mare Soils: Insights from Combined XPS and Analytical TEM Observations

Science.gov (United States)

Christoffersen, R.; Dukes, C.; Keller, L. P.; Baragiola, R.

2012-01-01

Solar wind ions are capable of altering the sur-face chemistry of the lunar regolith by a number of mechanisms including preferential sputtering, radiation-enhanced diffusion and sputter erosion of space weathered surfaces containing pre-existing compositional profiles. We have previously reported in-situ ion irradiation experiments supported by X-ray photoelectron spectroscopy (XPS) and analytical TEM that show how solar ions potentially drive Fe and Ti reduction at the monolayer scale as well as the 10-100 nm depth scale in lunar soils [1]. Here we report experimental data on the effect of ion irradiation on the major element surface composition in a mature mare soil.

Self-standing paper based anodes prepared from siliconcarbonitride-MoS2 composite for Li-ion battery applications

Science.gov (United States)

David, Lamuel; Singh, Gurpreet

2013-03-01

We study synthesis of free-standing polymer derived SiCN/ MoS2 composite paper anode for Li-ion battery application. This was achieved following a two-step approach: First, polysilazane was interfaced with exfoliated MoS2 nanosheets which upon pyrolysis resulted in SiCN/MoS2 composite. Second, dispersion of SiCN/MoS2 in isopropanol was vacuum filtered resulting in formation of a self-standing composite paper. Physical and chemical characterization of the composite was carried out by use of electron microscopy, Fourier transform infrared spectroscopy (FT-IR) and Thermo-gravimetric analysis (TGA). FT-IR data indicated complete conversion of polysilazane precursor to SiCN ceramic, while electron microscopy confirmed layered structure of the paper. Thermo-gravimetric analysis showed enhanced thermodynamic stability of the composite paper up to 800 °C. Electrochemical analysis of SiCN/MoS2 composite paper anodes showed that Li-ion can reversible intercalate in the voltage range of 0-2.5 V with a first cycle discharge capacity of 770 mAh/g at a current density of 100 mA/g.

Use of Composite Sorbents for the Removal of Copper (II ions from Aqueous Solution

Directory of Open Access Journals (Sweden)

Rebecca Oyedoyin Adeeyo

2015-01-01

Full Text Available Composite adsorbents are synthesized from two or more materials with different chemical and physical properties in order to increase their selectivity and the reusability. Researchers have developed and applied several novel composite materials for enhancing the removal of heavy metal. In this review, extensive list of composites developed via advanced technologies with specified characteristics for the removal of Cu (II ion are discussed. Emphases on their adsorption capacities, reusability, desorption and regeneration with improved mechanical strengths are presented. Conclusively, prospects and other challenges to be checked and addressed in future are outlined.

Removal of Cr(VI and Toxic Ions from Aqueous Solutions and Tannery Wastewater Using Polymer-Clay Composites

Directory of Open Access Journals (Sweden)

Abd El-Azeem Sallam

2017-10-01

Full Text Available Polymer-clay composites were prepared by natural zeolite (clinoptilolite or naturally local clay deposits in an N,N-methylene-bis-acrylamide as cross-linked. The resultant composites were used for the removal of Cr(VI from an aqueous solution. Additionally, their effects on soluble ions of tannery wastewater were investigated. The produced composites were characterized using X-ray diffraction (XRD, Fourier transform infrared spectroscopy (FT-IR, and scanning electron microscopy (SEM. The results showed that Cr(VI removal is dependent upon initial concentrations and pH. The adsorption quantity of Cr(VI onto the polymerized clay deposit followed by polymerized zeolite exhibited higher values than their original samples. The polymer-clay composite of clay deposit showed the highest removal of 76.3–100% overall initial concentrations of 10–50 mg L−1 and at initial pH of 2. Kinetics of Cr(VI removal by various sorbents was predicted using a pseudo–second order model. Our findings showed that the levels of salinity and various soluble ions (Cr2+, Na+, Cl− and SO42− in tannery wastewater are very high, and their levels were reduced after treatment, especially by polymerized sorbents. It could be concluded that the polymer-clay composites may be employed as a highly efficient sorbent for the removal of Cr(VI and toxic ions from the wastewater.

Transverse eV Ion Heating by Random Electric Field Fluctuations in the Plasmasphere

Science.gov (United States)

Artemyev, A. V.; Mourenas, D.; Agapitov, O. V.; Blum, L.

2017-01-01

Charged particle acceleration in the Earth inner magnetosphere is believed to be mainly due to the local resonant wave-particle interaction or particle transport processes. However, the Van Allen Probes have recently provided interesting evidence of a relatively slow transverse heating of eV ions at distances about 2-3 Earth radii during quiet times. Waves that are able to resonantly interact with such very cold ions are generally rare in this region of space, called the plasmasphere. Thus, non-resonant wave-particle interactions are expected to play an important role in the observed ion heating. We demonstrate that stochastic heating by random transverse electric field fluctuations of whistler (and possibly electromagnetic ion cyclotron) waves could explain this weak and slow transverse heating of H+ and O+ ions in the inner magnetosphere. The essential element of the proposed model of ion heating is the presence of trains of random whistler (hiss) wave packets, with significant amplitude modulations produced by strong wave damping, rapid wave growth, or a superposition of wave packets of different frequencies, phases, and amplitudes. Such characteristics correspond to measured characteristics of hiss waves in this region. Using test particle simulations with typical wave and plasma parameters, we demonstrate that the corresponding stochastic transverse ion heating reaches 0.07-0.2 eV/h for protons and 0.007-0.015 eV/h for O+ ions. This global temperature increase of the Maxwellian ion population from an initial Ti approx. 0.3 eV could potentially explain the observations.

Fabrication and modification of metal nanocluster composites using ion and laser beams

International Nuclear Information System (INIS)

Haglund, R.F. Jr.; Osborne, D.H. Jr.; Magruder, R.H. III; White, C.W.; Zuhr, R.A.; Townsend, P.D.; Hole, D.E.; Leuchtner, R.E.

1994-12-01

Metal nanocluster composites have attractive properties for applications in nonlinear optics. However, traditional fabrication techniques -- using melt-glass substrates -- are severely constrained by equilibrium thermodynamics and kinetics. This paper describes the fabrication of metal nanoclusters in both crystalline and glassy hosts by ion implantation and pulsed laser deposition. The size and size distribution of the metal nanoclusters can be modified by controlling substrate temperature during implantation, by subsequent thermal annealing, or by laser irradiation. The authors have characterized the optical response of the composites by absorption and third-order nonlinear-optical spectroscopies; electron and scanning-probe microscopies have been used to benchmark the physical characteristics of the composites. The outlook for controlling the structure and nonlinear optical response properties of these nanophase materials appears increasingly promising

Molecular Ions in Ion Upflows and their Effects on Hot Atomic Oxygen Production

Science.gov (United States)

Foss, V.; Yau, A. W.; Shizgal, B.

2017-12-01

We present new direct ion composition observations of molecular ions in auroral ion upflows from the CASSIOPE Enhanced Polar Outflow Probe (e-POP). These observed molecular ions are N2+, NO+, and possibly O2+, and are found to occur at all e-POP altitudes starting at about 400 km, during auroral substorms and the different phases of magnetic storms, sometimes with upflow velocities exceeding a few hundred meters per second and abundances of 5-10%. The dissociative recombination of both O2+ and NO+ was previously proposed as an important source of hot oxygen atoms in the topside thermosphere [Hickey et al., 1995]. We investigate the possible effect of the observed molecular ions on the production of hot oxygen atoms in the storm and substorm-time auroral thermosphere. We present numerical solutions of the Boltzmann equation for the steady-state oxygen energy distribution function, taking into account both the production of the hot atoms and their subsequent collisional relaxation. Our result suggests the formation of a hot oxygen population with a characteristic temperature on the order of 0.3 eV and constituting 1-5% of the oxygen density near the exobase. We discuss the implication of this result in the context of magnetosphere-ionosphere-thermosphere coupling.

Stable silicon/3D porous N-doped graphene composite for lithium-ion battery anodes with self-assembly

Science.gov (United States)

Tang, Xiaofu; Wen, Guangwu; Song, Yan

2018-04-01

We fabricate a novel 3D N-doped graphene/silicon composite for lithium-ion battery anodes, with Si nanoparticles uniformly dispersed and thoroughly embedded in the N-doped graphene matrix. The favorable structure of the composite results in a BET surface area and an average mesopore diameter of 189.2 m2 g-1 and 3.82 nm, respectively. The composite delivers reversible capacities as high as 1132 mA h g-1 after 100 cycles under a current of 5 A g-1 and 1017 mA h g-1 after 200 cycles at 1 A g-1, and exhibits an improved rate capability. The present approach shows promise for the preparation of other high-performance anode materials for lithium-ion batteries.

Can the TLR-4-Mediated Signaling Pathway Be “A Key Inflammatory Promoter for Sporadic TAA”?

Directory of Open Access Journals (Sweden)

Giovanni Ruvolo

2014-01-01

Full Text Available Thoracic aorta shows with advancing age various changes and a progressive deterioration in structure and function. As a result, vascular remodeling (VR and medial degeneration (MD occur as pathological entities responsible principally for the sporadic TAA onset. Little is known about their genetic, molecular, and cellular mechanisms. Recent evidence is proposing the strong role of a chronic immune/inflammatory process in their evocation and progression. Thus, we evaluated the potential role of Toll like receptor- (TLR- 4-mediated signaling pathway and its polymorphisms in sporadic TAA. Genetic, immunohistochemical, and biochemical analyses were assessed. Interestingly, the rs4986790 TLR4 polymorphism confers a higher susceptibility for sporadic TAA (OR=14.4, P=0.0008 and it represents, together with rs1799752 ACE, rs3918242 MMP-9, and rs2285053 MMP-2 SNPs, an independent sporadic TAA risk factor. In consistency with these data, a significant association was observed between their combined risk genotype and sporadic TAA. Cases bearing this risk genotype showed higher systemic inflammatory mediator levels, significant inflammatory/immune infiltrate, a typical MD phenotype, lower telomere length, and positive correlations with histopatological abnormalities, hypertension, smoking, and ageing. Thus, TLR4 pathway should seem to have a key role in sporadic TAA. It might represent a potential useful tool for preventing and monitoring sporadic TAA and developing personalized treatments.

Real-time detection of metal ions using conjugated polymer composite papers.

Science.gov (United States)

Lee, Ji Eun; Shim, Hyeon Woo; Kwon, Oh Seok; Huh, Yang-Il; Yoon, Hyeonseok

2014-09-21

Cellulose, a natural polymeric material, has widespread technical applications because of its inherent structural rigidity and high surface area. As a conjugated polymer, polypyrrole shows practical potential for a diverse and promising range of future technologies. Here, we demonstrate a strategy for the real-time detection and removal of metal ions with polypyrrole/cellulose (PPCL) composite papers in solution. Simply, the conjugated polymer papers had different chemical/physical properties by applying different potentials to them, which resulted in differentiable response patterns and adsorption efficiencies for individual metal ions. First, large-area PPCL papers with a diameter of 5 cm were readily obtained via vapor deposition polymerization. The papers exhibited both mechanical flexibility and robustness, in which polypyrrole retained its redox property perfectly. The ability of the PPCL papers to recognize metal ions was examined in static and flow cells, in which real-time current change was monitored at five different applied potentials (+1, +0.5, 0, -0.5, and -1 V vs. Ag/AgCl). Distinguishable signals in the PPCL paper responses were observed for individual metal ions through principal component analysis. Particularly, the PPCL papers yielded unique signatures for three metal ions, Hg(ii), Ag(i), and Cr(iii), even in a real sample, groundwater. The sorption of metal ions by PPCL papers was examined in the flow system. The PPCL papers had a greatly superior adsorption efficiency for Hg(ii) compared to that of the other metal ions. With the strong demand for the development of inexpensive, flexible, light-weight, and environmentally friendly devices, the fascinating characteristics of these PPCL papers are likely to provide good opportunities for low-cost paper-based flexible or wearable devices.

RNF43 is mutated less frequently in Lynch Syndrome compared with sporadic microsatellite unstable colorectal cancers.

Science.gov (United States)

Fennell, Lochlan J; Clendenning, Mark; McKeone, Diane M; Jamieson, Saara H; Balachandran, Samanthy; Borowsky, Jennifer; Liu, John; Kawamata, Futoshi; Bond, Catherine E; Rosty, Christophe; Burge, Matthew E; Buchanan, Daniel D; Leggett, Barbara A; Whitehall, Vicki L J

2018-01-01

The WNT signaling pathway is commonly altered during colorectal cancer development. The E3 ubiquitin ligase, RNF43, negatively regulates the WNT signal through increased ubiquitination and subsequent degradation of the Frizzled receptor. RNF43 has recently been reported to harbor frequent truncating frameshift mutations in sporadic microsatellite unstable (MSI) colorectal cancers. This study assesses the relative frequency of RNF43 mutations in hereditary colorectal cancers arising in the setting of Lynch syndrome. The entire coding region of RNF43 was Sanger sequenced in 24 colorectal cancers from 23 patients who either (i) carried a germline mutation in one of the DNA mismatch repair genes (MLH1, MSH6, MSH2, PMS2), or (ii) showed immunohistochemical loss of expression of one or more of the DNA mismatch repair proteins, was BRAF wild type at V600E, were under 60 years of age at diagnosis, and demonstrated no promoter region methylation for MLH1 in tumor DNA. A validation cohort of 44 colorectal cancers from mismatch repair germline mutation carriers from the Australasian Colorectal Cancer Family Registry (ACCFR) were sequenced for the most common truncating mutation hotspots (X117 and X659). RNF43 mutations were found in 9 of 24 (37.5%) Lynch syndrome colorectal cancers. The majority of mutations were frameshift deletions in the G659 G7 repeat tract (29%); 2 cancers (2/24, 8%) from the one patient harbored frameshift mutations at codon R117 (C6 repeat tract) within exon 3. In the ACCFR validation cohort, RNF43 hotspot mutations were identified in 19/44 (43.2%) of samples, which was not significantly different to the initial series. The proportion of mutant RNF43 in Lynch syndrome related colorectal cancers is significantly lower than the previously reported mutation rate found in sporadic MSI colorectal cancers. These findings identify further genetic differences between sporadic and hereditary colorectal cancers. This may be because Lynch Syndrome cancers

An Amorphous Carbon Nitride Composite Derived from ZIF-8 as Anode Material for Sodium-Ion Batteries.

Science.gov (United States)

Fan, Jing-Min; Chen, Jia-Jia; Zhang, Qian; Chen, Bin-Bin; Zang, Jun; Zheng, Ming-Sen; Dong, Quan-Feng

2015-06-08

An composite comprising amorphous carbon nitride (ACN) and zinc oxide is derived from ZIF-8 by pyrolysis. The composite is a promising anode material for sodium-ion batteries. The nitrogen content of the ACN composite is as high as 20.4 %, and the bonding state of nitrogen is mostly pyridinic, as determined by X-ray photoelectron spectroscopy (XPS). The composite exhibits an excellent Na(+) storage performance with a reversible capacity of 430 mA h g(-1) and 146 mA h g(-1) at current densities of 83 mA g(-1) and 8.33 A g(-1) , respectively. A specific capacity of 175 mA h g(-1) was maintained after 2000 cycles at 1.67 A g(-1) , with only 0.016 % capacity degradation per cycle. Moreover, an accelerating rate calorimetry (ARC) test demonstrates the excellent thermal stability of the composite, with a low self heating rate and high onset temperature (210 °C). These results shows its promise as a candidate material for high-capacity, high-rate anodes for sodium-ion batteries. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Case study of inclined sporadic E layers in the Earth's ionosphere observed by CHAMP/GPS radio occultations: Coupling between the tilted plasma layers and internal waves

Science.gov (United States)

Gubenko, Vladimir N.; Pavelyev, A. G.; Kirillovich, I. A.; Liou, Y.-A.

2018-04-01

We have used the radio occultation (RO) satellite data CHAMP/GPS (Challenging Minisatellite Payload/Global Positioning System) for studying the ionosphere of the Earth. A method for deriving the parameters of ionospheric structures is based upon an analysis of the RO signal variations in the phase path and intensity. This method allows one to estimate the spatial displacement of a plasma layer with respect to the ray perigee, and to determine the layer inclination and height correction values. In this paper, we focus on the case study of inclined sporadic E (Es) layers in the high-latitude ionosphere based on available CHAMP RO data. Assuming that the internal gravity waves (IGWs) with the phase-fronts parallel to the ionization layer surfaces are responsible for the tilt angles of sporadic plasma layers, we have developed a new technique for determining the parameters of IGWs linked with the inclined Es structures. A small-scale internal wave may be modulating initially horizontal Es layer in height and causing a direction of the plasma density gradient to be rotated and aligned with that of the wave propagation vector k. The results of determination of the intrinsic wave frequency and period, vertical and horizontal wavelengths, intrinsic vertical and horizontal phase speeds, and other characteristics of IGWs under study are presented and discussed.

Imaging the interphase of carbon fiber composites using transmission electron microscopy: Preparations by focused ion beam, ion beam etching, and ultramicrotomy

Directory of Open Access Journals (Sweden)

Wu Qing

2015-10-01

Full Text Available Three sample preparation techniques, focused ion beam (FIB, ion beam (IB etching, and ultramicrotomy (UM were used in comparison to analyze the interphase of carbon fiber/epoxy composites using transmission electron microscopy. An intact interphase with a relatively uniform thickness was obtained by FIB, and detailed chemical analysis of the interphase was investigated by electron energy loss spectroscopy. It shows that the interphase region is 200 nm wide with an increasing oxygen-to-carbon ratio from 10% to 19% and an almost constant nitrogen-to-carbon ratio of about 3%. However, gallium implantation of FIB tends to hinder fine structure analysis of the interphase. For IB etching, the interphase region is observed with transition morphology from amorphous resin to nano-crystalline carbon fiber, but the uneven sample thickness brings difficulty for quantitative chemical analysis. Moreover, UM tends to cause damage and/or deformation on the interphase. These results are meaningful for in-depth understanding on the interphase characteristic of carbon fiber composites.

A chemically activated graphene-encapsulated LiFePO4 composite for high-performance lithium ion batteries.

Science.gov (United States)

Ha, Jeonghyun; Park, Seung-Keun; Yu, Seung-Ho; Jin, Aihua; Jang, Byungchul; Bong, Sungyool; Kim, In; Sung, Yung-Eun; Piao, Yuanzhe

2013-09-21

A composite of modified graphene and LiFePO4 has been developed to improve the speed of charging-discharging and the cycling stability of lithium ion batteries using LiFePO4 as a cathode material. Chemically activated graphene (CA-graphene) has been successfully synthesized via activation by KOH. The as-prepared CA-graphene was mixed with LiFePO4 to prepare the composite. Microscopic observation and nitrogen sorption analysis have revealed the surface morphologies of CA-graphene and the CA-graphene/LiFePO4 composite. Electrochemical properties have also been investigated after assembling coin cells with the CA-graphene/LiFePO4 composite as a cathode active material. Interestingly, the CA-graphene/LiFePO4 composite has exhibited better electrochemical properties than the conventional graphene/LiFePO4 composite as well as bare LiFePO4, including exceptional speed of charging-discharging and excellent cycle stability. That is because the CA-graphene in the composite provides abundant porous channels for the diffusion of lithium ions. Moreover, it acts as a conducting network for easy charge transfer and as a divider, preventing the aggregation of LiFePO4 particles. Owing to these properties of CA-graphene, LiFePO4 could demonstrate enhanced and stably long-lasting electrochemical performance.

PRKAG3 polymorphisms associated with sporadic Wolff–Parkinson–White syndrome among a Taiwanese population

Directory of Open Access Journals (Sweden)

Ken-Pen Weng

2016-12-01

Conclusion: This study shows that PRKAG3-230 may be associated with sporadic WPW syndrome among a Taiwanese population. Further studies are warranted to elucidate the role of mutations in AMPK subunit genes other than PRKAG3-230 in sporadic WPW syndrome.

Case Studies in e-RPL and e-PR

Science.gov (United States)

Cameron, Roslyn; Miller, Allison

2014-01-01

The use of ePortfolios for recognition of prior learning (e-RPL) and for professional recognition (e-PR) is slowly gaining in popularity in the VET sector however their use is sporadic across educational sectors, disciplines, educational institutions and professions. Added to this is an array of purposes and types of e-RPL and e-PR models and…

An emerging role for misfolded wild-type SOD1 in sporadic ALS pathogenesis

Directory of Open Access Journals (Sweden)

Melissa S Rotunno

2013-12-01

Full Text Available Amyotrophic lateral sclerosis (ALS is a fatal neurodegenerative disorder that targets motor neurons, leading to paralysis and death within a few years of disease onset. While several genes have been linked to the inheritable, or familial, form of ALS, much less is known about the cause(s of sporadic ALS, which accounts for approximately 90% of ALS cases. Due to the clinical similarities between familial and sporadic ALS, it is plausible that both forms of the disease converge on a common pathway and, therefore, involve common factors. Recent evidence suggests the Cu,Zn-superoxide dismutase (SOD1 protein to be one such factor that is common to both sporadic and familial ALS. In 1993, mutations were uncovered in SOD1 that represent the first known genetic cause of familial ALS. While the exact mechanism of mutant-SOD1 toxicity is still not known today, most evidence points to a gain of toxic function that stems, at least in part, from the propensity of this protein to misfold. In the wild-type SOD1 protein, non-genetic perturbations such as metal depletion, disruption of the quaternary structure, and oxidation, can also induce SOD1 to misfold. In fact, these aforementioned post-translational modifications cause wild-type SOD1 to adopt a toxic conformation that is similar to familial ALS-linked SOD1 variants. These observations, together with the detection of misfolded wild-type SOD1 within human post-mortem sporadic ALS samples, have been used to support the controversial hypothesis that misfolded forms of wild-type SOD1 contribute to sporadic ALS pathogenesis. In this review, we present data from the literature that both support and contradict this hypothesis. We also discuss SOD1 as a potential therapeutic target for both familial and sporadic ALS.

Non-standard γγ →l sup(+)l sup(-) processes in relativistic heavy ion collisions

International Nuclear Information System (INIS)

Almeida, L.D.; Natale, A.A.; Novaes, S.F.; Eboli, O.J.P.

1991-02-01

We study lepton pair production in heavy ion collisions with emphasis in nonstandard contributions of the QRD subprocess γ γ → l sup(+)l sup(-). The existence of compositeness of fermions and/or bosons can be tested in this reaction up to the TeV mass scale. We show that for some processes the capabilities of relativistic heavy ion colliders to disclose new physics supplant the possibilities of e sup(+)e sup(-) or pp-bar machines. In particular, the spin zero composite particles which couples predominantly to two-photons, predicted in composite models, can be studied in a broad range of masses. (author)

The genetics of radiation-induced and sporadic osteosarcoma: a unifying theory?

International Nuclear Information System (INIS)

Rosemann, Michael; Kuosaite, Virginija; Nathrath, Michaela; Atkinson, Michael J.

2002-01-01

Cancer is a disease of the genome, with the neoplastic phenotype being passed from one cell generation to the other. Radiation-induced cancer has often been considered to represent a unique entity amongst neoplasia, with the energy deposition being held responsible for both direct (gene mutations) and indirect (bystander effects, induced instability etc) alterations to the cellular genome. However, radiogenic tumours in man and experimental animals appear to be physiologically and genetically indistinguishable from their sporadic counterparts, suggesting that the aetiologies of these two tumour types are in fact closely related. We have conducted a general screen of the genetic alterations in radiation-induced mouse osteosarcoma, a tumour that is histopathologically indistinguishable from human sporadic osteosarcoma. Comparison of the two tumour types indicates the existence of a common set of genetic changes, providing additional evidence to support the concept that the molecular pathology of radiation-induced malignancy is no different to that of sporadic cancers. (author)

A Combined Thermodynamics & Computational Method to Assess Lithium Composition in Anode and Cathode of Lithium Ion Batteries

International Nuclear Information System (INIS)

Zhang, Wenyu; Jiang, Lianlian; Van Durmen, Pauline; Saadat, Somaye; Yazami, Rachid

2016-01-01

With aim to address the open question of accurate determination of lithium composition in anode and cathode at a defined state of charge (SOC) of lithium ion batteries (LIB), we developed a method combining electrochemical thermodynamic measurements (ETM) and computational data fitting protocol. It is a common knowledge that in a lithium ion battery the SOC of anode and cathode differ from the SOC of the full-cell. Differences are in large part due to irreversible lithium losses within cell and to electrode mass unbalance. This implies that the lithium composition range in anode and in cathode during full charge and discharge cycle in full-cell is different from the composition range achieved in lithium half-cells of anode and cathode over their respective full SOC ranges. To the authors knowledge there is no unequivocal and practical method to determine the actual lithium composition of electrodes in a LIB, hence their SOC. Yet, accurate lithium composition assessment is fundamental not only for understanding the physics of electrodes but also for optimizing cell performances, particularly energy density and cycle life.

Comparing Sporadic and Outbreak-associated Foodborne Illness

Centers for Disease Control (CDC) Podcasts

2016-11-04

Dr. Eric Ebel, a veterinarian and risk analyst with USDA’s Food Safety and Inspection Service, discusses his article on sporadic and outbreak-associated cases of foodborne illness.  Created: 11/4/2016 by National Center for Emerging and Zoonotic Infectious Diseases (NCEZID).   Date Released: 11/4/2016.

Determination of isotopic composition of uranium in microparticles by secondary ion mass spectrometry

International Nuclear Information System (INIS)

Veniaminov, N.N.; Kolesnikov, O.N.; Stebel'kov, V.A.

1992-01-01

Aerosol particles including uranium in their composition are specific atmospheric polutants. Uranium is used as nuclear fuel in atomic power stations and in spacecraft power units, and also as a component of nuclear warheads. In order to monitor the discharge of uranium-containing aerosol particles to the atmosphere, they must first be identified. As an example, one may cite an investigation of the elemental composition and radioactivity of particles formed in the accident at the Chernobyl atomic power station. One of the most informative indicators of the origin of uranium-containing aerosol particles is the isotopic composition of the uranium. Secondary ion mass spectrometry (SIMS) offers unique possibilities for the measurement of isotope ratios in individual microscopic objects. At the same time, a measurement of isotope ratios of sulfur in microsection of galenite PbS 2 has shown that the application of SIMS for these purposes is seriously limited by the difference in yield of secondary ions for isotopes with different masses. These discrimination effects, in the case of light elements such as boron, may result in distortion of the isotope ratios by several percent. In the case of heavy elements, however, the effect is less significant, amounting to about 0.5% for lead isotopes. 13 refs., 3 figs., 1 tab

Brain sonography in African infants with complicated sporadic ...

African Journals Online (AJOL)

Background: To determine the structural findings in brain sonography of African infants with complicated sporadic bacterial meningitis. Materials and Methods: Retrospective assessment of medical records of patients who underwent brain sonography on account of complicated bacterial meningitis. The brain sonography ...

Fabrication of flower-like tin/carbon composite microspheres as long-lasting anode materials for lithium ion batteries

Energy Technology Data Exchange (ETDEWEB)

Kang, Tae-Woo [Department of Chemical Engineering, College of Engineering, Hanyang University, Seoul, 133-791 (Korea, Republic of); Lim, Hyung-Seok [Department of WCU Engineering, College of Engineering, Hanyang University, Seoul, 133-791 (Korea, Republic of); Park, Seong-Jin [Department of Chemical Engineering, College of Engineering, Hanyang University, Seoul, 133-791 (Korea, Republic of); Sun, Yang-Kook [Department of WCU Engineering, College of Engineering, Hanyang University, Seoul, 133-791 (Korea, Republic of); Suh, Kyung-Do, E-mail: kdsuh@hanyang.ac.kr [Department of Chemical Engineering, College of Engineering, Hanyang University, Seoul, 133-791 (Korea, Republic of)

2017-01-01

In this work, we report the fabrication of the flower-like tin/carbon (Sn/C) composite microspheres using sulfonated semi-interpenetrating polystyrene (SPS) microspheres as a carbon precursor. The sulfonation degree of SPS has great effects on the resulting particle size, morphology, amount of introduced Sn, and the carbonization yield of the microspheres after heat treatment. The obtained Sn/C composite microspheres were characterized by scanning electron microscopy (SEM), focused-ion beam SEM, and X-ray diffraction. The flower-like Sn/C composite electrodes exhibited higher charge-discharge capacities than those of graphite as an anode material for a lithium ion battery. In addition, they show a long lasting cyclability, even through 400 cycles. - Highlights: • Tin nanocrystals are introduced in flower-like carbon spheres with many ripples. • Long lasting cyclability is exhibited at 1 C rate up to 400 cycles. • Tin content of composite spheres depends on chemical treatment of polymer microspheres.

Silver effect of Co–Ni composite material on energy storage and structural behavior for Li-ion batteries

International Nuclear Information System (INIS)

Gnanamuthu, RM.; Prasanna, K.; Subburaj, T.; Jo, Yong Nam; Lee, Chang Woo

2013-01-01

Ag powder has been comparatively applied to the Co–Ni materials preparing by mixing method and the prepared electrodes were used as negative electrodes for Li-ion batteries applications. The prepared Co–Ni and Ag–Co–Ni with 10 wt.% of Ag composite electrodes are characterized by XRD, FE-SEM with EDX, impedance and electrochemical charge-discharge studies. These electrochemical studies are demonstrated at current rates of 0.1 C and 0.5 C between 0.01 and 2.0 V vs. Li/Li + . The porous Co–Ni and Ag–Co–Ni composite materials are electrochemically tested in lithium half cells. The porous Ag–Co–Ni composite material demonstrates that the initial and end of discharge capacity up to 20th cycles is, respectively, 860 and 715 mAh g −1 at 0.1 C rate maintaining at approximately 83%. The porous Ag–Co–Ni composite electrode may be a good candidate for high power lithium-ion batteries.

Low energy ion scattering as a tool for surface structure and composition analysis

International Nuclear Information System (INIS)

Armour, D.G.

1980-01-01

Low energy ion scattering is finding increasing application in the study of areas such as gas adsorption, thin film deposition and surface damage creation and annealing during ion irradiation where structural and compositional changes occurring in only the outermost atomic layer need to be monitored. The capabilities of the technique and the ways in which it has been developed for different types of analysis depend strongly on the fundamental atomic collision processes taking place at the surface and it is these processes, together with examples of their role in analysis applications, that form the subject of this paper. (author)

Specific deficit of colour-colour short-term memory binding in sporadic and familial Alzheimer's disease.

Science.gov (United States)

Parra, Mario A; Sala, Sergio Della; Abrahams, Sharon; Logie, Robert H; Méndez, Luis Guillermo; Lopera, Francisco

2011-06-01

Short-term memory binding of visual features which are processed across different dimensions (shape-colour) is impaired in sporadic Alzheimer's disease, familial Alzheimer's disease, and in asymptomatic carriers of familial Alzheimer's disease. This study investigated whether Alzheimer's disease also impacts on within-dimension binding processes. The study specifically explored whether visual short-term memory binding of features of the same type (colour-colour) is sensitive to Alzheimer's disease. We used a neuropsychological battery and a short-term memory binding task to assess patients with sporadic Alzheimer's disease (Experiment 1), familial Alzheimer's disease (Experiment 2) due to the mutation E280A of the Presenilin-1 gene and asymptomatic carriers of the mutation. The binding task assessed change detection within arrays of unicoloured objects (Colour Only) or bicoloured objects the colours of which had to be remembered separately (Unbound Colours) or together (Bound Colours). Performance on the Bound Colours condition (1) explained the largest proportion of variance between patients (sporadic and familial Alzheimer's disease), (2) combined more sensitivity and specificity for the disease than other more traditional neuropsychological tasks, (3) identified asymptomatic carriers of the mutation even when traditional neuropsychological measures and other measures of short-term memory did not and, (4) contrary to shape-colour binding, correlated with measures of hippocampal functions. Colour-colour binding and shape-colour binding both appear to be sensitive to AD even though they seem to rely on different brain mechanisms. Copyright © 2011 Elsevier Ltd. All rights reserved.

Studies of local degradation phenomena in composite cathodes for lithium-ion batteries

International Nuclear Information System (INIS)

Kerlau, Marie; Marcinek, Marek; Srinivasan, Venkat; Kostecki, Robert M.

2007-01-01

LiNi 0.8 Co 0.15 Al 0.05 O 2 and LiNi 1/3 Co 1/3 Mn 1/3 O 2 composite cathodes were cycled in model cells to study interfacial phenomena that could lead to electrode degradation. Ex situ spectroscopic analysis of the tested cathodes, which suffered substantial power and capacity loss, showed that the state of charge (SOC) of oxide particles on the cathode surface was highly non-uniform despite the deep discharge of the Li-ion cell at the end of the test. The inconsistent kinetic behavior of individual oxide particles was attributed to the degradation of electronic pathways within the composite cathodes. A simple theoretical model based on a distributed network showed that an increase of the contact resistance between composite electrode particles may be responsible for non-uniform local kinetic behavior of individual oxide particles and the overall degradation of electrochemical performance of composite electrodes

Three male patients with sporadic acute hepatitis E in Sendai, Japan, who were domestically infected with hepatitis E virus of genotype III or IV.

Science.gov (United States)

Yamamoto, Takeshi; Suzuki, Hiroshi; Toyota, Takayoshi; Takahashi, Masaharu; Okamoto, Hiroaki

2004-01-01

Recent studies indicate that hepatitis E virus (HEV) infection occurs not only in developing countries but also in industrialized nations. However, the characteristics of domestic infections of hepatitis E in Japan are not fully understood. We analyzed serum samples from 34 patients who were seen at a city hospital in Sendai, Japan, between January 1997 and December 2002, and who had been given the diagnosis of sporadic acute hepatitis of non-A, non-B, non-C etiology. Among these 34 patients, 3 (9%; all men; aged 54, 59, and 61 years) were positive for both IgG and IgM anti-HEV antibodies and for HEV RNA. The HEV isolates (HE-JAS1 and HE-JAS3) obtained from case 1 and case 3, respectively, segregated into genotype III; they had the highest nucleotide sequence identity, of 99.5% and 99.0%, with HE-JA7 and HE-JA8, respectively, both of which had been isolated in Iwate, a neighboring prefecture of Sendai. In contrast, the remaining HEV isolate (HE-JAS2), obtained from case 2, segregated into genotype IV; it had the highest nucleotide sequence identity, of 99.8% and 99.3%, with JKK-Sap and HE-JA3, respectively, both of which had been isolated in Hokkaido, Japan, although case 2 had never been to Hokkaido. Our three patients with hepatitis E had not traveled abroad in the preceding 1 year, had had no contact with pigs, and no history of blood transfusion. These results indicate that HEV should be considered as an etiological agent of acute hepatitis of non-A, non-B, non-C etiology in Japan. The risk factor(s) for acquiring domestic HEV infection in Japan needs to be clarified in future studies.

A New Class of Ternary Compound for Lithium-Ion Battery: from Composite to Solid Solution.

Science.gov (United States)

Wang, Jiali; Wu, Hailong; Cui, Yanhua; Liu, Shengzhou; Tian, Xiaoqing; Cui, Yixiu; Liu, Xiaojiang; Yang, Yin

2018-02-14

Searching for high-performance cathode materials is a crucial task to develop advanced lithium-ion batteries (LIBs) with high-energy densities for electrical vehicles (EVs). As a promising lithium-rich material, Li 2 MnO 3 delivers high capacity over 200 mAh g -1 but suffers from poor structural stability and electronic conductivity. Replacing Mn 4+ ions by relatively larger Sn 4+ ions is regarded as a possible strategy to improve structural stability and thus cycling performance of Li 2 MnO 3 material. However, large difference in ionic radii of Mn 4+ and Sn 4+ ions leads to phase separation of Li 2 MnO 3 and Li 2 SnO 3 during high-temperature synthesis. To prepare solid-solution phase of Li 2 MnO 3 -Li 2 SnO 3 , a buffer agent of Ru 4+ , whose ionic radius is in between that of Mn 4+ and Sn 4+ ions, is introduced to assist the formation of a single solid-solution phase. The results show that the Li 2 RuO 3 -Li 2 MnO 3 -Li 2 SnO 3 ternary system evolves from mixed composite phases into a single solid-solution phase with increasing Ru content. Meanwhile, discharge capacity of this ternary system shows significantly increase at the transformation point which is ascribed to the improvement of Li + /e - transportation kinetics and anionic redox chemistry for solid-solution phase. The role of Mn/Sn molar ratio of Li 2 RuO 3 -Li 2 MnO 3 -Li 2 SnO 3 ternary system has also been studied. It is revealed that higher Sn content benefits cycling stability of the system because Sn 4+ ions with larger sizes could partially block the migration of Mn 4+ and Ru 4+ from transition metal layer to Li layer, thus suppressing structural transformation of the system from layered-to-spinel phase. These findings may enable a new route for exploring ternary or even quaternary lithium-rich cathode materials for LIBs.

Left frontal hub connectivity delays cognitive impairment in autosomal-dominant and sporadic Alzheimer’s disease

Science.gov (United States)

Franzmeier, Nicolai; Düzel, Emrah; Jessen, Frank; Buerger, Katharina; Levin, Johannes; Duering, Marco; Dichgans, Martin; Haass, Christian; Suárez-Calvet, Marc; Fagan, Anne M; Paumier, Katrina; Benzinger, Tammie; Masters, Colin L; Morris, John C; Perneczky, Robert; Janowitz, Daniel; Catak, Cihan; Wolfsgruber, Steffen; Wagner, Michael; Teipel, Stefan; Kilimann, Ingo; Ramirez, Alfredo; Rossor, Martin; Jucker, Mathias; Chhatwal, Jasmeer; Spottke, Annika; Boecker, Henning; Brosseron, Frederic; Falkai, Peter; Fliessbach, Klaus; Heneka, Michael T; Laske, Christoph; Nestor, Peter; Peters, Oliver; Fuentes, Manuel; Menne, Felix; Priller, Josef; Spruth, Eike J; Franke, Christiana; Schneider, Anja; Kofler, Barbara; Westerteicher, Christine; Speck, Oliver; Wiltfang, Jens; Bartels, Claudia; Araque Caballero, Miguel Ángel; Metzger, Coraline; Bittner, Daniel; Weiner, Michael; Lee, Jae-Hong; Salloway, Stephen; Danek, Adrian; Goate, Alison; Schofield, Peter R; Bateman, Randall J; Ewers, Michael

2018-01-01

Abstract Patients with Alzheimer’s disease vary in their ability to sustain cognitive abilities in the presence of brain pathology. A major open question is which brain mechanisms may support higher reserve capacity, i.e. relatively high cognitive performance at a given level of Alzheimer’s pathology. Higher functional MRI-assessed functional connectivity of a hub in the left frontal cortex is a core candidate brain mechanism underlying reserve as it is associated with education (i.e. a protective factor often associated with higher reserve) and attenuated cognitive impairment in prodromal Alzheimer’s disease. However, no study has yet assessed whether such hub connectivity of the left frontal cortex supports reserve throughout the evolution of pathological brain changes in Alzheimer’s disease, including the presymptomatic stage when cognitive decline is subtle. To address this research gap, we obtained cross-sectional resting state functional MRI in 74 participants with autosomal dominant Alzheimer’s disease, 55 controls from the Dominantly Inherited Alzheimer’s Network and 75 amyloid-positive elderly participants, as well as 41 amyloid-negative cognitively normal elderly subjects from the German Center of Neurodegenerative Diseases multicentre study on biomarkers in sporadic Alzheimer’s disease. For each participant, global left frontal cortex connectivity was computed as the average resting state functional connectivity between the left frontal cortex (seed) and each voxel in the grey matter. As a marker of disease stage, we applied estimated years from symptom onset in autosomal dominantly inherited Alzheimer’s disease and cerebrospinal fluid tau levels in sporadic Alzheimer’s disease cases. In both autosomal dominant and sporadic Alzheimer’s disease patients, higher levels of left frontal cortex connectivity were correlated with greater education. For autosomal dominant Alzheimer’s disease, a significant left frontal cortex connectivity �

Correlation of precursor and product ions in single-stage high resolution mass spectrometry. A tool for detecting diagnostic ions and improving the precursor elemental composition elucidation

Energy Technology Data Exchange (ETDEWEB)

Borràs, S. [Departament de Química Analítica, Universitat de Barcelona, Martí i Franquès 1-11, 08028 Barcelona (Spain); Kaufmann, A., E-mail: anton.kaufmann@klzh.ch [Official Food Control Authority, Fehrenstrasse 15, 8032 Zürich (Switzerland); Companyó, R. [Departament de Química Analítica, Universitat de Barcelona, Martí i Franquès 1-11, 08028 Barcelona (Spain)

2013-04-15

Highlights: ► We are describing a technique to spot ions which are derived from each other. ► Single stage high resolution data is used. ► This “in silicon” technique is compared to conventional precursor scan. ► Some applications for this technique are presented. -- Abstract: Monitoring of common diagnostic fragments is essential for recognizing molecules which are members of a particular compound class. Up to now, unit resolving tandem quadrupole mass spectrometers, operating in the precursor ion scan mode, have been typically used to perform such analysis. By means of high-resolution mass spectrometry (HRMS) a much more sensitive and selective detection can be achieved. However, using a single-stage HRMS instrument, there is no unequivocal link to the corresponding precursor ion, since such instrumentation does not permit a previous precursor selection. Thus, to address this limitation, an in silico approach to locate precursor ions, based on diagnostic fragments, was developed. Implemented as an Excel macro, the algorithm rapidly assembles and surveys exact mass data to provide a list of feasible precursor candidates according to the correlation of the chromatographic peak shape profile and other additional filtering criteria (e.g. neutral losses and isotopes). The macro was tested with two families of veterinary drugs, sulfonamides and penicillins, which are known to yield diagnostic product ions when fragmented. Data sets obtained from different food matrices (fish and liver), both at high and low concentration of the target compounds, were investigated in order to evaluate the capabilities and limitations of the reported approach. Finally, other possible applications of this technique, such as the elucidation of elemental compositions based on product ions and corresponding neutral losses, were also presented and discussed.

Correlation of precursor and product ions in single-stage high resolution mass spectrometry. A tool for detecting diagnostic ions and improving the precursor elemental composition elucidation

International Nuclear Information System (INIS)

Borràs, S.; Kaufmann, A.; Companyó, R.

2013-01-01

Highlights: ► We are describing a technique to spot ions which are derived from each other. ► Single stage high resolution data is used. ► This “in silicon” technique is compared to conventional precursor scan. ► Some applications for this technique are presented. -- Abstract: Monitoring of common diagnostic fragments is essential for recognizing molecules which are members of a particular compound class. Up to now, unit resolving tandem quadrupole mass spectrometers, operating in the precursor ion scan mode, have been typically used to perform such analysis. By means of high-resolution mass spectrometry (HRMS) a much more sensitive and selective detection can be achieved. However, using a single-stage HRMS instrument, there is no unequivocal link to the corresponding precursor ion, since such instrumentation does not permit a previous precursor selection. Thus, to address this limitation, an in silico approach to locate precursor ions, based on diagnostic fragments, was developed. Implemented as an Excel macro, the algorithm rapidly assembles and surveys exact mass data to provide a list of feasible precursor candidates according to the correlation of the chromatographic peak shape profile and other additional filtering criteria (e.g. neutral losses and isotopes). The macro was tested with two families of veterinary drugs, sulfonamides and penicillins, which are known to yield diagnostic product ions when fragmented. Data sets obtained from different food matrices (fish and liver), both at high and low concentration of the target compounds, were investigated in order to evaluate the capabilities and limitations of the reported approach. Finally, other possible applications of this technique, such as the elucidation of elemental compositions based on product ions and corresponding neutral losses, were also presented and discussed

Development of methodics for the characterization of the composition of the ion-collision-induced secondary-particle flux by comparison of the yield contributions of photoinduced ion formation processes

International Nuclear Information System (INIS)

Vering, Guido

2008-01-01

The aim of this work was to develop a method to distinguish between different ion formation processes and to determine the influence of these processes on the total number of detected monatomic ions of a certain element. A vector/matrix-formalism was developed, which describes the physical processes of sputtering, ion formation, mass separation and detection in laser-SNMS. In the framework of the method developed, based on this theoretic formalism, changes in the secondary flux contribution of the respective element were observed by comparing the detected monatomic ion yield obtained in specifically aligned (SIMS and) laser-SNMS experiments. The yields resulting from these experiments were used to calculate characteristic numbers to compare the flux composition from different surfaces. The potential of the method was demonstrated for the elements boron, iron and gadolinium by investigating the changes in the flux composition of secondary particles sputtered from metallic surfaces, as a function of the oxygen concentration at the surface. Finally, combined laser-SNMS depth profiles and images, obtained with both laser systems, were presented to demonstrate how the parallel detection of the three differently originated ion signals of the same element can be used to get additional information about the composition of the flux of secondary particles synchronously during the analysis of elemental distributions. In this respect the presented method can be a very helpful tool to prevent misleading interpretations of SIMS or laser-SNMS data. (orig.)

Genetic overlap between apparently sporadic motor neuron diseases

NARCIS (Netherlands)

van Blitterswijk, Marka; Vlam, Lotte; van Es, Michael A.; van der Pol, W.-Ludo; Hennekam, Eric A. M.; Dooijes, Dennis; Schelhaas, Helenius J.; van der Kooi, Anneke J.; de Visser, Marianne; Veldink, Jan H.; van den Berg, Leonard H.

2012-01-01

Progressive muscular atrophy (PMA) and amyotrophic lateral sclerosis (ALS) are devastating motor neuron diseases (MNDs), which result in muscle weakness and/or spasticity. We compared mutation frequencies in genes known to be associated with MNDs between patients with apparently sporadic PMA and

Neuroendocrine Differentiation in Sporadic CRC and Hereditary Nonpolyosis Colorectal Cancer

Directory of Open Access Journals (Sweden)

M. H. Sun

2004-01-01

Full Text Available Extent neuroendocrine differentiation can be encountered in many human neoplasm derived from different organs and systems using immunohistochemistry and ultrastructural techniques. The tumor cells' behaviors resemble those of neurons and neuroendocrine cells. The presence of neuroendocrine differentiation reputedly appears to be associated with a poorer prognosis than the adenocarcinoma counterparts in sporadic human neoplasm. In this review the neuroendocrine carcinoma and the adenocarcinoma with neuroendocrine differentiation of colon and rectum both in sporadic colorectal carcinoma and the hereditary nonpolyposis colorectal cancer, the relationship of neuroendocrine differentiation and some possible molecular pathways in tumorogenesis of colorectal cancer will be discussed. Possible treatment strategy will also be addressed.

Early Detection of Sporadic Pancreatic Cancer

Science.gov (United States)

Chari, Suresh T.; Kelly, Kimberly; Hollingsworth, Michael A.; Thayer, Sarah P.; Ahlquist, David A.; Andersen, Dana K.; Batra, Surinder K.; Brentnall, Teresa A.; Canto, Marcia; Cleeter, Deborah F.; Firpo, Matthew A.; Gambhir, Sanjiv Sam; Go, Vay Liang W.; Hines, O. Joe; Kenner, Barbara J.; Klimstra, David S.; Lerch, Markus M.; Levy, Michael J.; Maitra, Anirban; Mulvihill, Sean J.; Petersen, Gloria M.; Rhim, Andrew D.; Simeone, Diane M.; Srivastava, Sudhir; Tanaka, Masao; Vinik, Aaron I.; Wong, David

2015-01-01

Abstract Pancreatic cancer (PC) is estimated to become the second leading cause of cancer death in the United States by 2020. Early detection is the key to improving survival in PC. Addressing this urgent need, the Kenner Family Research Fund conducted the inaugural Early Detection of Sporadic Pancreatic Cancer Summit Conference in 2014 in conjunction with the 45th Anniversary Meeting of the American Pancreatic Association and Japan Pancreas Society. This seminal convening of international representatives from science, practice, and clinical research was designed to facilitate challenging interdisciplinary conversations to generate innovative ideas leading to the creation of a defined collaborative strategic pathway for the future of the field. An in-depth summary of current efforts in the field, analysis of gaps in specific areas of expertise, and challenges that exist in early detection is presented within distinct areas of inquiry: Case for Early Detection: Definitions, Detection, Survival, and Challenges; Biomarkers for Early Detection; Imaging; and Collaborative Studies. In addition, an overview of efforts in familial PC is presented in an addendum to this article. It is clear from the summit deliberations that only strategically designed collaboration among investigators, institutions, and funders will lead to significant progress in early detection of sporadic PC. PMID:25931254

Genetic Relatedness among Nontypeable Pneumococci Implicated in Sporadic Cases of Conjunctivitis

Science.gov (United States)

Barker, Jason H.; Musher, Daniel M.; Silberman, Ronald; Phan, Hoang M.; Watson, David A.

1999-01-01

Nontypeable Streptococcus pneumoniae is a common cause of epidemic conjunctivitis. A previous molecular fingerprinting study identified a clone of nontypeable pneumococcus that was responsible for a recent outbreak of conjunctivitis. In the present study, we examined the extent to which pneumococci that cause sporadic cases of conjunctivitis are related to this epidemic strain. Using arbitrarily primed BOX-PCR, we have determined that, of 10 nontypeable pneumococci causing sporadic conjunctivitis, 5 were clonal and closely related to a previous outbreak strain, whereas 5 others were genetically diverse. PMID:10565927

Mutation analysis for DJ-1 in sporadic and familial parkinsonism: screening strategy in parkinsonism.

Science.gov (United States)

Tomiyama, Hiroyuki; Li, Yuanzhe; Yoshino, Hiroyo; Mizuno, Yoshikuni; Kubo, Shin-Ichiro; Toda, Tatsushi; Hattori, Nobutaka

2009-05-22

DJ-1 mutations cause autosomal recessive parkinsonism (ARP). Although some reports of DJ-1 mutations have been published, there is lack of information on the prevalence of these mutations in large-scale studies of both familial and sporadic parkinsonism. In this genetic screening study, we analyzed the distribution and frequency of DJ-1 mutations by direct nucleotide sequencing of coding exons and exon-intron boundaries of DJ-1, in 386 parkin-negative parkinsonism patients (371 index cases: 67 probands of autosomal recessive parkinsonism families, 90 probands of autosomal dominant parkinsonism families, 201 patients with sporadic parkinsonism, and 13 with unknown family histories) from 12 countries (Japan 283, China 27, Taiwan 22, Korea 22, Israel 16, Turkey 5, Philippines 2, Bulgaria 2, Greece 2, Tunisia 1, USA 2, Ukraine 1, unknown 1). None had causative mutation in DJ-1, suggesting DJ-1 mutation is very rare among patients with familial and sporadic parkinsonism from Asian countries and those with other ethnic background. This is in contrast to the higher frequencies and worldwide distribution of parkin- and PINK1-related parkinsonism in ARP and sporadic parkinsonism. Thus, after obtaining clinical information, screening for mutations in (1) parkin, (2) PINK1, (3) DJ-1, (4) ATP13A2 should be conducted in that order, in ARP and sporadic parkinsonism, based on their reported frequencies. In addition, haplotype analysis should be employed to check for homozygosity of 1p36, which harbors a cluster of causative genes for ARP such as DJ-1, PINK1 and ATP13A2 in ARP and sporadic parkinsonism, especially in parkinsonism with consanguinity.

Neuropathological and biochemical criteria to identify acquired Creutzfeldt-Jakob disease among presumed sporadic cases.

Science.gov (United States)

Kobayashi, Atsushi; Parchi, Piero; Yamada, Masahito; Mohri, Shirou; Kitamoto, Tetsuyuki

2016-06-01

As an experimental model of acquired Creutzfeldt-Jakob disease (CJD), we performed transmission studies of sporadic CJD using knock-in mice expressing human prion protein (PrP). In this model, the inoculation of the sporadic CJD strain V2 into animals homozygous for methionine at polymorphic codon 129 (129 M/M) of the PRNP gene produced quite distinctive neuropathological and biochemical features, that is, widespread kuru plaques and intermediate type abnormal PrP (PrP(Sc) ). Interestingly, this distinctive combination of molecular and pathological features has been, to date, observed in acquired CJD but not in sporadic CJD. Assuming that these distinctive phenotypic traits are specific for acquired CJD, we revisited the literature and found two cases showing widespread kuru plaques despite the 129 M/M genotype, in a neurosurgeon and in a patient with a medical history of neurosurgery without dura mater grafting. By Western blot analysis of brain homogenates, we revealed the intermediate type of PrP(Sc) in both cases. Furthermore, transmission properties of brain extracts from these two cases were indistinguishable from those of a subgroup of dura mater graft-associated iatrogenic CJD caused by infection with the sporadic CJD strain V2. These data strongly suggest that the two atypical CJD cases, previously thought to represent sporadic CJD, very likely acquired the disease through exposure to prion-contaminated brain tissues. Thus, we propose that the distinctive combination of 129 M/M genotype, kuru plaques, and intermediate type PrP(Sc) , represents a reliable criterion for the identification of acquired CJD cases among presumed sporadic cases. © 2015 Japanese Society of Neuropathology.

Rôle des complexes ion/neutre dans les décompositions unimoléculaires d'ions [beta]-hydroxy acylium

Science.gov (United States)

Morizur, J.-P.; Chapon, E.

1994-06-01

Résumé Les réactions des ions [beta]-hydroxy acylium métastables CH3CH(OH)CH2CO+ (1) formés en phase gazeuse par perte de CH3O à partir du méthyl 3-hydroxy butyrate ionisé sont présentées et discutées. Le marquage aux isotopes stables a montré que la formation des ions CH2=CHCH2CO+ et CH3CO+ est précédée d'échanges d'atomes d'hydrogène et d'oxygène. L'utilisation des techniques de spectrométrie de masse a fourni des preuves expérimentales sur les isomérisations et dissociations de l'ion 1. On propose que la perte d'eau s'effectue à partir de CH2=CHCH2C(=O)OH+2, la formation de CH3CO+ implique un complexe ion/neutre [CH3CHO/CH3CO+]. L'interprétation des résultats est étayée par des données thermodynamiques. The reactions of metastable [beta]-hydroxy acylium ions CH3CH(OH)CH2CO+ (1) generated in the gas phase by loss of CH3O from ionized methyl 3-hydroxy butyrate are reported and discussed. Isotopic labelling shows that the dissociation, which produces the acylium ions CH2=CHCH2CO+ and CH3CO+, is preceded by hydrogen and oxygen atom exchange. Mass spectrometry techniques have provided experimental information of the isomerization and dissociation of ion 1. Loss of water is proposed to occur from CH2=CHCH2C(=O)OH+2; formation of CH3CO+ involves an ion/neutral complex [CH3CHO/CH3CO+]. Interpretation of data is supported by thermochemistry.

Study of chloride ion transport of composite by using cement and starch as a binder

Energy Technology Data Exchange (ETDEWEB)

Armynah, Bidayatul; Halide, Halmar; Zahrawani,; Reski, Nurhadi; Tahir, Dahlang, E-mail: dtahir@fmipa.unhas.ac.id [Department of Physics, Hasanuddin University, Makassar 90245 Indonesia (Indonesia)

2016-03-11

This study presents the chemical bonding and the structural properties of composites from accelerator chloride test migration (ACTM). The volume fractions between binder (cement and starch) and charcoal in composites are 20:80 and 60:40. The effect of the binder to the chemical composition, chemical bonding, and structural properties before and after chloride ion passing through the composites was determined by X-ray fluorescence (XRF), by Fourier transform infra-red (FTIR), and x-ray diffraction (XRD), respectively. From the XRD data, XRF data, and the FTIR data shows the amount of chemical composition, the type of binding, and the structure of composites are depending on the type of binder. The amount of chloride migration using starch as binder is higher than that of cement as a binder due to the density effects.

Colorimetric detection and removal of radioactive Co ions using sodium alginate-based composite beads

International Nuclear Information System (INIS)

Kim, Daigeun; Jo, Ara; Yang, Hee-Man; Seo, Bum-Kyoung; Lee, Kune-Woo; Lee, Taek Seung

2017-01-01

Highlights: • Organic/inorganic hybridized alginate beads were newly synthesized via sol-gel chemistry. • Interaction between the azopyridine and metal ion is the main cause of Co ion detection. • The beads showed improved stability and least leakage of azopyridine during use. • Removal of Co ion was assessed by the ion-exchange of carboxylate groups in alginate. • The beads with dual functions of detection and removal of Co ion were successfully accomplished. - Abstract: We demonstrate a simple method for the visual determination and removal of Co ions using a bead-shaped, capturing probe based on hybridized sodium alginate. For Co ions, the designed protocol consisted of three main constituents: an azopyridine-based Co ion-probe for visual detection; sodium alginate as an adsorbent for the Co ion and a bead construct for removal and structure; silica as a linker for the probe and the alginate, leading to a robust structure. When the composite beads were exposed to Co ions, the yellow color of the beads turned to intensive violet and the color intensity was associated with the Co ion concentration. The color variation was quantified using red-green-blue (RGB) color values that were obtained with a scanner and evaluated with Photoshop. The technique achieved both visual recognition with obvious color change of the beads and efficient removal of the radioactive 60 Co ion. The sensing and removal of any radioactive isotope could be achieved with an appropriate sensing probe, to provide a simple and universal platform for remediation.

Colorimetric detection and removal of radioactive Co ions using sodium alginate-based composite beads

Energy Technology Data Exchange (ETDEWEB)

Kim, Daigeun; Jo, Ara [Organic and Optoelectronic Materials Laboratory, Department of Organic Materials Engineering, Chungnam National University, Daejeon 34134 (Korea, Republic of); Yang, Hee-Man; Seo, Bum-Kyoung; Lee, Kune-Woo [Decontamination and Decommissioning Research Division, Korea Atomic Energy Research Institute, Daejeon 34057 (Korea, Republic of); Lee, Taek Seung, E-mail: tslee@cnu.ac.kr [Organic and Optoelectronic Materials Laboratory, Department of Organic Materials Engineering, Chungnam National University, Daejeon 34134 (Korea, Republic of)

2017-03-15

Highlights: • Organic/inorganic hybridized alginate beads were newly synthesized via sol-gel chemistry. • Interaction between the azopyridine and metal ion is the main cause of Co ion detection. • The beads showed improved stability and least leakage of azopyridine during use. • Removal of Co ion was assessed by the ion-exchange of carboxylate groups in alginate. • The beads with dual functions of detection and removal of Co ion were successfully accomplished. - Abstract: We demonstrate a simple method for the visual determination and removal of Co ions using a bead-shaped, capturing probe based on hybridized sodium alginate. For Co ions, the designed protocol consisted of three main constituents: an azopyridine-based Co ion-probe for visual detection; sodium alginate as an adsorbent for the Co ion and a bead construct for removal and structure; silica as a linker for the probe and the alginate, leading to a robust structure. When the composite beads were exposed to Co ions, the yellow color of the beads turned to intensive violet and the color intensity was associated with the Co ion concentration. The color variation was quantified using red-green-blue (RGB) color values that were obtained with a scanner and evaluated with Photoshop. The technique achieved both visual recognition with obvious color change of the beads and efficient removal of the radioactive {sup 60}Co ion. The sensing and removal of any radioactive isotope could be achieved with an appropriate sensing probe, to provide a simple and universal platform for remediation.

The effect of correlations on the entropy and hadrochemical composition in heavy ion reactions

International Nuclear Information System (INIS)

Barz, H.-W.; Biro, T.S.; Lukacs, B.; Zimanyi, J.

1987-01-01

It is shown that spatial correlations between the constituent particles of a gas lead to roughly excluded volume type corrections in the equation of state. These corrections will appreciably change the hadrochemical composition of fireballs formed in heavy ion reactions. (author) 29 refs.; 3 figs

Three-dimensional iron sulfide-carbon interlocked graphene composites for high-performance sodium-ion storage

DEFF Research Database (Denmark)

Huang, Wei; Sun, Hongyu; Shangguan, Huihui

2018-01-01

Three-dimensional (3D) carbon-wrapped iron sulfide interlocked graphene (Fe7S8@C-G) composites for high-performance sodium-ion storage are designed and produced through electrostatic interactions and subsequent sulfurization. The iron-based metal–organic frameworks (MOFs, MIL-88-Fe) interact with...

Changes in phase composition and stress state of surface layers of VK20 hard alloy after ion bombardment

International Nuclear Information System (INIS)

Platonov, G.L.; Leonov, E.Yu.; Anikin, V.N.; Anikeev, A.I.

1988-01-01

Titanium ion bombardment of the surface of the hard VK20 alloy is studied for its effect on variations in the phase and chemical composition of its surface layers. It is stated that ion treatment results in the appearance of the η-phase of Co 6 W 6 C composition in the surface layer of the VK20 alloy, in the increase of distortions and decrease of coherent scattering blocks of the hard alloy carbide phase. Such a bombardment is found to provoke a transition of the plane-stressed state of the hard alloy surface into the volume-stressed state. It is established that ion treatment does not cause an allotropic transition of the cobalt phase α-modification, formed during grinding of the hard alloy, into the β-modification

In-flight calibration of satellite ion composition data using artificial intelligence methods

International Nuclear Information System (INIS)

Waldemark, J.

1995-11-01

The scope of this report is to evaluate some of the cognitive analyzing techniques that are available and that might be useful for calibration, validation and data analysis of a satellite measurement system. As an example, these cognitive techniques are used to perform a post launch calibration of the three-dimensional ion composition, TICS, on the Freja satellite. 17 refs, 28 figs, 6 tabs

Contribution of TARDBP mutations to sporadic amyotrophic lateral sclerosis.

Science.gov (United States)

Daoud, H; Valdmanis, P N; Kabashi, E; Dion, P; Dupré, N; Camu, W; Meininger, V; Rouleau, G A

2009-02-01

Mutations in the TARDBP gene, which encodes the TAR DNA binding protein (TDP-43), have been described in individuals with familial and sporadic amyotrophic lateral sclerosis (ALS). We screened the TARDBP gene in 285 French sporadic ALS patients to assess the frequency of TARDBP mutations in ALS. Six individuals had potentially deleterious mutations of which three were novel including a Y374X truncating mutation and P363A and A382P missense mutations. This suggests that TARDBP mutations may predispose to ALS in approximately 2% of the individuals followed in this study. Our findings, combined with those from other collections, brings the total number of mutations in unrelated ALS patients to 17, further suggesting that mutations in the TARDBP gene have an important role in the pathogenesis of ALS.

Physico-Chemical and Electrochemical Properties of Nanoparticulate NiO/C Composites for High Performance Lithium and Sodium Ion Battery Anodes

Directory of Open Access Journals (Sweden)

Amaia Iturrondobeitia

2017-12-01

Full Text Available Nanoparticulate NiO and NiO/C composites with different carbon proportions have been prepared for anode application in lithium and sodium ion batteries. Structural characterization demonstrated the presence of metallic Ni in the composites. Morphological study revealed that the NiO and Ni nanoparticles were well dispersed in the matrix of amorphous carbon. The electrochemical study showed that the lithium ion batteries (LIBs, containing composites with carbon, have promising electrochemical performances, delivering specific discharge capacities of 550 mAh/g after operating for 100 cycles at 1C. These excellent results could be explained by the homogeneity of particle size and structure, as well as the uniform distribution of NiO/Ni nanoparticles in the in situ generated amorphous carbon matrix. On the other hand, the sodium ion battery (NIB with the NiO/C composite revealed a poor cycling stability. Post-mortem analyses revealed that this fact could be ascribed to the absence of a stable Solid Electrolyte Interface (SEI or passivation layer upon cycling.

Measurements of ion temperature and plasma hydrogenic composition by collective Thomson scattering in neutral beam heated discharges at TEXTOR

DEFF Research Database (Denmark)

Stejner Pedersen, Morten; Salewski, Mirko; Korsholm, Søren Bang

2013-01-01

A method is developed to perform plasma composition and ion temperature measurements across the plasma minor radius in TEXTOR based on ion cyclotron structures in collective Thomson scattering spectra. By gradually moving the scattering volume, we obtain measurements across the outer midplane of ...

Carbon Cryogel Silicon Composite Anode Materials for Lithium Ion Batteries

Science.gov (United States)

Woodworth James; Baldwin, Richard; Bennett, William

2010-01-01

A variety of materials are under investigation for use as anode materials in lithium-ion batteries, of which, the most promising are those containing silicon. 10 One such material is a composite formed via the dispersion of silicon in a resorcinol-formaldehyde (RF) gel followed by pyrolysis. Two silicon-carbon composite materials, carbon microspheres and nanofoams produced from nano-phase silicon impregnated RF gel precursors have been synthesized and investigated. Carbon microspheres are produced by forming the silicon-containing RF gel into microspheres whereas carbon nano-foams are produced by impregnating carbon fiber paper with the silicon containing RF gel to create a free standing electrode. 1-4,9 Both materials have demonstrated their ability to function as anodes and utilize the silicon present in the material. Stable reversible capacities above 400 mAh/g for the bulk material and above 1000 mAh/g of Si have been observed.

Polymer-derived-SiCN ceramic/graphite composite as anode material with enhanced rate capability for lithium ion batteries

Science.gov (United States)

Graczyk-Zajac, M.; Fasel, C.; Riedel, R.

2011-08-01

We report on a new composite material in view of its application as a negative electrode in lithium-ion batteries. A commercial preceramic polysilazane mixed with graphite in 1:1 weight ratio was transformed into a SiCN/graphite composite material through a pyrolytic polymer-to-ceramic conversion at three different temperatures, namely 950 °C, 1100 °C and 1300 °C. By means of Raman spectroscopy we found successive ordering of carbon clusters into nano-crystalline graphitic regions with increasing pyrolysis temperature. The reversible capacity of about 350 mAh g-1 was measured with constant current charging/discharging for the composite prepared at 1300 °C. For comparison pure graphite and pure polysilazane-derived SiCN ceramic were examined as reference materials. During fast charging and discharging the composite material demonstrates enhanced capacity and stability. Charging and discharging in half an hour lead to about 200 and 10 mAh g-1, for the composite annealed at 1300 °C and pure graphite, respectively. A clear dependence between the final material capacity and pyrolysis temperature is found and discussed with respect to possible application in batteries, i.e. practical discharging potential limit. The best results in terms of capacity recovered under 1 V and high rate capability were also obtained for samples synthesized at 1300 °C.

Prevalence of Abnormal Cervical Smears from Sporadic Screening ...

African Journals Online (AJOL)

The aim of the study was to find the prevalence of abnormal smears in an unscreened population of sexually active women attending a gynaecological clinic. “Pap” smears were taken sporadically for cytological examination from sexually active women attending gynaecological clinics at the Federal Medical Centre Gombe.

MAJOR MOLECULAR GENETIC DRIVERS IN SPORADIC PRIMARY HYPERPARATHYROIDISM.

Science.gov (United States)

Arnold, Andrew

2016-01-01

Primary hyperparathyroidism is primarily due to a solitary parathyroid adenoma but multi-gland disease, parathyroid carcinoma, and ectopic parathyroid hormone production can occur. Although primary hyperparathyroidism mostly presents sporadically, strong familial predispositions also exist. Much is known about heritable genetic mutations responsible for these syndromes, including multiple endocrine neoplasia types 1 and 2A, hyperparathyroidism-jaw tumor syndrome, and familial hypocalciuric hypercalcemia. Acquired mutations in common sporadic hyperparathyroidism have also been discovered. Here we focus on the most common and well-established genetic drivers: 1) involvement of the oncogene cyclin D1 in human neoplasia was first established in parathyroid adenomas, followed by recognition of its importance in other tumor types including breast cancer and B-lymphoid malignancy; and 2) somatic mutation of the MEN1 gene, first identified as the source of pathogenic germline mutations in patients with familial endocrinopathies, is found in a substantial fraction of non-familial parathyroid adenomas.

Lifetime of anode polymer in magnetically insulated ion diodes for high-intensity pulsed ion beam generation

International Nuclear Information System (INIS)

Zhu, X. P.; Dong, Z. H.; Han, X. G.; Xin, J. P.; Lei, M. K.

2007-01-01

Generation of high-intensity pulsed ion beam (HIPIB) has been studied experimentally using polyethylene as the anode polymer in magnetically insulated ion diodes (MIDs) with an external magnetic field. The HIPIB is extracted from the anode plasma produced during the surface discharging process on polyethylene under the electrical and magnetic fields in MIDs, i.e., high-voltage surface breakdown (flashover) with bombardments by electrons. The surface morphology and the microstructure of the anode polymer are characterized using scanning electron microscopy and differential scanning calorimetry, respectively. The surface roughening of the anode polymer results from the explosive release of trapped gases or newly formed gases under the high-voltage discharging, leaving fractured surfaces with bubble formation. The polyethylene in the surface layer degrades into low-molecular-weight polymers such as polyethylene wax and paraffin under the discharging process. Both the surface roughness and the fraction of low molecular polymers apparently increase as the discharging times are prolonged for multipulse HIPIB generation. The changes in the surface morphology and the composition of anode polymer lead to a noticeable decrease in the output of ion beam intensity, i.e., ion current density and diode voltage, accompanied with an increase in instability of the parameters with the prolonged discharge times. The diode voltage (or surface breakdown voltage of polymer) mainly depends on the surface morphology (or roughness) of anode polymers, and the ion current density on the composition of anode polymers, which account for the two stages of anode polymer degradation observed experimentally, i.e., stage I which has a steady decrease of the two parameters and stage II which shows a slow decrease, but with an enhanced fluctuation of the two parameters with increasing pulses of HIPIB generation

COL11A1 in FAP polyps and in sporadic colorectal tumors

International Nuclear Information System (INIS)

Fischer, Heléne; Salahshor, Sima; Stenling, Roger; Björk, Jan; Lindmark, Gudrun; Iselius, Lennart; Rubio, Carlos; Lindblom, Annika

2001-01-01

We previously reported that the α-1 chain of type 11 collagen (COL11A1), not normally expressed in the colon, was up-regulated in stromal fibroblasts in most sporadic colorectal carcinomas. Patients with germline mutations in the APC gene show, besides colonic polyposis, symptoms of stromal fibroblast involvement, which could be related to COL11A1 expression. Most colorectal carcinomas are suggested to be a result of an activated Wnt- pathway, most often involving an inactivation of the APC gene or activation of β-catenin. We used normal and polyp tissue samples from one FAP patient and a set of 37 sporadic colorectal carcinomas to find out if the up-regulation of COL11A1 was associated with an active APC/β-catenin pathway. In this study we found a statistically significant difference in COL11A1 expression between normal tissue and adenomas from one FAP patient, and all adenomas gave evidence for an active APC/β-catenin pathway. An active Wnt pathway has been suggested to involve stromal expression of WISP-1. We found a strong correlation between WISP-1 and COL11A1 expression in sporadic carcinomas. Our results suggest that expression of COL11A1 in colorectal tumors could be associated with the APC/β-catenin pathway in FAP and sporadic colorectal cancer

Nano-sized LiFePO4/C composite with core-shell structure as cathode material for lithium ion battery

International Nuclear Information System (INIS)

Liu, Yang; Zhang, Min; Li, Ying; Hu, Yemin; Zhu, Mingyuan; Jin, Hongming; Li, Wenxian

2015-01-01

Graphical abstract: Nano-sized LiFePO4/C composite with core-shell structure was fabricated via a well-designed approach as cathode material forlithium ion battery. The nano-sized LiFePO4/C composite with whole carbon shell coating layer showed an excellent electrical performance. - Abstract: Nano-sized composite with LiFePO 4 -core and carbon-shell was synthesized via a facile route followed by heat treatment at 650 °C. X-ray diffraction (XRD) shows that the core is well crystallized LiFePO 4 . The electron microscopy (SEM and TEM) observations show that the core-shell structured LiFePO 4 /C composite coating with whole carbon shell layer of ∼2.8 nm, possesses a specific surface area of 51 m 2 g −1 . As cathode material for lithium ion battery, the core-shell LiFePO 4 /C composite exhibits high initial capacity of 161 mAh g −1 at 0.1 C, excellent high-rate discharge capacity of 135 mAh g −1 at 5 C and perfect cycling retention of 99.6% at 100 th cycle. All these promising results should be contributed to the core-shell nanostructure which prevents collapse of the particle structure in the long-term charge and discharge cycles, as well as the large surface area of the nano-sized LiFePO 4 /C composite which enhances the electronic conductivity and shortens the distance of lithium ion diffusion

Clinicopathologic factors identify sporadic mismatch repair-defective colon cancers

DEFF Research Database (Denmark)

Halvarsson, Britta; Anderson, Harald; Domanska, Katarina

2008-01-01

Identification of sporadic mismatch repair (MMR)-defective colon cancers is increasingly demanded for decisions on adjuvant therapies. We evaluated clinicopathologic factors for the identification of these prognostically favorable tumors. Histopathologic features in 238 consecutive colon cancers...

Ion-conductive properties of polyether-based composite electrolytes filled with mesoporous silica, alumina and titania

International Nuclear Information System (INIS)

Tominaga, Yoichi; Endo, Masanori

2013-01-01

Composite polymer electrolytes were prepared consisting of amorphous polyether, Li salt and mesoporous inorganic filler, and we investigated their ion-conductive properties. We synthesized three types of filler, mesoporous silica, alumina and titania (MP-Si, Al, Ti), and characterized their structural and physicochemical properties using SEM, TEM, SAXS and BET surface area measurements. From these measurements, we confirmed that MP fillers have well-defined arrays of mesoporous and hexagonal structures. Dependence on the MP filler content of the glass transition temperature (T g ) revealed that the addition of filler to original polyether-salt electrolyte causes T g decrease, to due to the dissociation of aggregated ions such as triples or crystalline complex domains. The MP-Ti composites had the greatest ionic conductivity (1.4 × 10 −5 S/cm, 7.5 wt% at 30 °C) of all samples, and the values were more than double that of the original. The addition of MP-Ti also increased the lithium transference number, because the electrolyte/filler interface provided active sites that increase mobile Li ions and conducting paths so as to enhance the mobility

Spherical nanostructured Si/C composite prepared by spray drying technique for lithium ion batteries anode

Energy Technology Data Exchange (ETDEWEB)

Chen Libao [Energy Science and Technology Laboratory, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai 200050 (China); Graduate School of Chinese Academy of Sciences, Beijing 100049 (China); Xie Xiaohua [Energy Science and Technology Laboratory, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai 200050 (China); Graduate School of Chinese Academy of Sciences, Beijing 100049 (China); Wang Baofeng [Department of Chemical Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Wang Ke [Energy Science and Technology Laboratory, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai 200050 (China); Xie Jingying [Energy Science and Technology Laboratory, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai 200050 (China) and Graduate School of Chinese Academy of Sciences, Beijing 100049 (China)]. E-mail: jyxie@mail.sim.ac.cn

2006-07-15

Spherical nanostructured Si/C composite was prepared by spray drying technique, followed by heat treatment, in which nanosized silicon and fine graphite particles were homogeneously embedded in carbon matrix pyrolyzed by phenol formaldehyde resin. Cyclic voltammetry tests showed two pairs of redox peaks corresponding to lithiation and delithiation of Si/C composite. The Si/C composite exhibited a reversible capacity of 635 mAh g{sup -1} and good cycle performance used in lithium ion batteries. To improve cycle performance of this Si/C composite further, the carbon-coated Si/C composite was synthesized by the second spray drying and heat treatment processing. The cycle performance of carbon-coated Si/C composite was improved significantly, which was attributed to the formation of stable SEI passivation layers on the outer surface of carbon shell which protected the bared silicon from exposing to electrolyte directly.

Spherical nanostructured Si/C composite prepared by spray drying technique for lithium ion batteries anode

International Nuclear Information System (INIS)

Chen Libao; Xie Xiaohua; Wang Baofeng; Wang Ke; Xie Jingying

2006-01-01

Spherical nanostructured Si/C composite was prepared by spray drying technique, followed by heat treatment, in which nanosized silicon and fine graphite particles were homogeneously embedded in carbon matrix pyrolyzed by phenol formaldehyde resin. Cyclic voltammetry tests showed two pairs of redox peaks corresponding to lithiation and delithiation of Si/C composite. The Si/C composite exhibited a reversible capacity of 635 mAh g -1 and good cycle performance used in lithium ion batteries. To improve cycle performance of this Si/C composite further, the carbon-coated Si/C composite was synthesized by the second spray drying and heat treatment processing. The cycle performance of carbon-coated Si/C composite was improved significantly, which was attributed to the formation of stable SEI passivation layers on the outer surface of carbon shell which protected the bared silicon from exposing to electrolyte directly

Morphology variation, composition alteration and microstructure changes in ion-irradiated 1060 aluminum alloy

Science.gov (United States)

Wan, Hao; Si, Naichao; Wang, Quan; Zhao, Zhenjiang

2018-02-01

Morphology variation, composition alteration and microstructure changes in 1060 aluminum irradiated with 50 keV helium ions were characterized by field emission scanning electron microscopy (FESEM) equipped with x-ray elemental scanning, 3D measuring laser microscope and transmission electron microscope (TEM). The results show that, helium ions irradiation induced surface damage and Si-rich aggregates in the surfaces of irradiated samples. Increasing the dose of irradiation, more damages and Si-rich aggregates would be produced. Besides, defects such as dislocations, dislocation loops and dislocation walls were the primary defects in the ion implanted layer. The forming of surface damages were related with preferentially sputtering of Al component. While irradiation-enhanced diffusion and irradiation-induced segregation resulted in the aggregation of impurity atoms. And the aggregation ability of impurity atoms were discussed based on the atomic radius, displacement energy, lattice binding energy and surface binding energy.

Composite films prepared by plasma ion-assisted deposition (IAD) for design and fabrication of antireflection coatings in visible and near-infrared spectral regions

Science.gov (United States)

Tsai, Rung-Ywan; Ho, Fang C.

1994-11-01

Ion-assisted deposition (IAD) processes configured with a well-controlled plasma source at the center base of a vacuum chamber, which accommodates two independent e-gun sources, is used to deposition TiO2MgF2 and TiO2-SiO2 composite films of selected component ratios. Films prepared by this technology are found durable, uniform, and nonabsorbing in visible and near-IR regions. Single- and multilayer antireflection coatings with refractive index from 1.38 to 2.36 at (lambda) equals 550 nm are presented. Methods of enhancement in optical performance of these coatings are studied. The advantages of AR coatings formed by TiO2-MgF2 composite films over those similar systems consisting of TiO2-SiO2 composite films in both visible and near-IR regions are also presented.

Nanostructure Sn-Co-C composite lithium ion battery electrode with unique stability and high electrochemical performance

International Nuclear Information System (INIS)

Li Mengyuan; Liu Chunling; Shi Meirong; Dong Wensheng

2011-01-01

Nanostructure Sn-Co-C composites with different compositions are synthesized by a simple solution polymerization using inexpensive raw materials followed by pyrolysis in nitrogen atmosphere. The nanostructure Sn-Co-C composites are characterized using various analytic techniques. The results show that the electrochemical performances of the composites are strongly dependent on their structure and composition. Among these composites the Sn-Co-C-1 with a weight composition of Sn 0.31 Co 0.09 C 0.6 exhibits high reversible capacity and excellent cycleability when used as an anode for rechargeable lithium ion batteries. This composite is composed of SnCo 2 , SnCo, Sn and amorphous carbon, and the nanoparticles of SnCo 2 , SnCo and Sn are uniformly dispersed into the amorphous carbon matrix, the average diameter of these metal nanoparticles is 8.44 nm.

Ion plasma deposition of oxide films with graded-stoichiometry composition: Experiment and simulation

Science.gov (United States)

Volpyas, V. A.; Tumarkin, A. V.; Mikhailov, A. K.; Kozyrev, A. B.; Platonov, R. A.

2016-07-01

A method of ion plasma deposition is proposed for obtaining thin multicomponent films with continuously graded composition in depth of the film. The desired composition-depth profile is obtained by varying the working gas pressure during deposition in the presence of an additional adsorbing screen in the drift space between a sputtered target and substrate. Efficiency of the proposed method is confirmed by Monte Carlo simulation of the deposition of thin films of Ba x Sr1- x TiO3 (BSTO) solid solution. It is demonstrated that, during sputtering of a Ba0.3Sr0.7TiO3 target, the parameter of composition stoichiometry in the growing BSTO film varies in the interval of x = 0.3-0.65 when the gas pressure is changed within 2-60 Pa.

Adsorption behavior of carboxylated cellulose nanocrystal—polyethyleneimine composite for removal of Cr(VI) ions

Energy Technology Data Exchange (ETDEWEB)

Liu, Chao; Jin, Ru-Na; Ouyang, Xiao-kun, E-mail: xkouyang@zjou.edu.cn; Wang, Yang-Guang

2017-06-30

Highlights: • A carboxylated cellulose nanocrystal-polyethyleneimine composite (CCN-PEI) was prepared. • The as-prepared CCN-PEI was characterized by SEM, TEM, FT-IR, and XPS. • Results suggested that the reusable CCN-PEI could remove Cr(VI) from aqueous solutions with a high adsorption capacity. • The adsorption isotherm, thermodynamics, and kinetics of the adsorption process are also discussed. - Abstract: In this study, a composite adsorbent (CCN-PEI) composed of carboxylated cellulose nanocrystals (CCN) and polyethyleneimine (PEI) was prepared through an amidation reaction between the carboxyl groups of the CCN and the amine groups of the PEI. The adsorption performance of the CCN-PEI was tested by removing Cr(VI) ions from aqueous solutions. The physicochemical properties of the CCN and the Cr(VI) ion-loaded CCN-PEI were studied using scanning electron microscopy (SEM), transmission electron microscopy, Fourier-transform infrared spectroscopy, and X-ray photoelectron spectroscopy. To investigate the adsorption kinetics of Cr(VI) ions onto this newly developed CCN-PEI, we performed experiments under different adsorption conditions, by varying the contact time, solution pH, initial Cr(VI) ion concentration, and adsorption temperature. The prepared CCN-PEI exhibited an encouraging uptake capacity of 358.42 mg × g{sup −1}. The adsorption process was fast: within the first 100 min, Cr(VI) ion adsorption onto the CCN-PEI was about 65%, and the adsorption equilibrium was reached within 250 min. Kinetics experiments indicated that the adsorption process could be described by a pseudo-second-order kinetic model. Furthermore, our adsorption equilibrium data fit the Langmuir isotherms well. The calculated thermodynamic parameters, such as the free energy change (ΔG = −2.93 kJ × mol{sup −1}), enthalpy change (ΔH = −5.69 kJ × mol{sup −1}), and entropy change (ΔS = −9.14 kJ × mol{sup −1}), indicate that the adsorption of Cr(VI) ions onto CCN

Latitudinal distribution of the Jovian plasma sheet ions observed by Juno JADE-I

Science.gov (United States)

Kim, T. K. H.; Valek, P. W.; McComas, D. J.; Allegrini, F.; Bagenal, F.; Bolton, S. J.; Connerney, J. E. P.; Ebert, R. W.; Levin, S.; Louarn, P.; Pollock, C. J.; Ranquist, D. A.; Szalay, J.; Thomsen, M. F.; Wilson, R. J.

2017-12-01

The Jovian plasma sheet is a region where the centrifugal force dominates the heavy ion plasma. Properties of the plasma sheet ions near the equatorial plane have been studied with in-situ measurements from the Pioneer, Voyager, and Galileo spacecraft. However, the ion properties for the off-equator regions are not well known due to the limited measurements. Juno is the first polar orbiting spacecraft that can investigate the high latitude region of the Jovian magnetosphere. With Juno's unique trajectory, we will investigate the latitudinal distribution of the Jovian plasma sheet ions using measurements from the Jovian Auroral Distributions Experiment Ion sensor (JADE-I). JADE-I measures an ion's energy-per-charge (E/Q) from 0.01 keV/q to 46.2 keV/q with an electrostatic analyzer (ESA) and a mass-per-charge (M/Q) up to 64 amu/q with a carbon-foil-based time-of-flight (TOF) mass spectrometer. We have shown that the ambiguity between and (both have M/Q of 16) can be resolved in JADE-I using a semi-empirical simulation tool based on carbon foil effects (i.e., charge state modification, angular scattering, and energy loss) from incident ions passing through the TOF mass spectrometer. Based on the simulation results, we have developed an Ion Composition Analysis Tool (ICAT) that determines ion composition at each energy step of JADE-I (total of 64 steps). The velocity distribution for each ion species can be obtained from the ion composition as a function of each energy step. Since there is an ambipolar electric field due to mobile electrons and equatorially confined heavy ions, we expect to see acceleration along the field line. This study will show the species separated velocity distribution at various latitudes to investigate how the plasma sheet ions evolve along the field line.

Updated clinical diagnostic criteria for sporadic Creutzfeldt-Jakob disease

NARCIS (Netherlands)

I. Zerr; K. Kallenberg; D.M. Summers; C. Romero; A. Taratuto; U. Heinemann; M. Breithaupt; D. Varges; B. Meissner; A. Ladogana (Anna); M. Schuur (Maaike); S. Haik; S.J. Collins (Steven); G.H. Jansen (Gerard); G.B. Stokin; J. Pimentel; E. Hewer; D. Collie; P. Smith; H. Roberts; J.P. Brandel; P. Tikka-Kleemola (Päivi); M. Pocchiari (Maurizio); C. Begue; P. Cras (Patrick); R.G. Will; P. Sanchez-Juan (Pascual)

2009-01-01

textabstractSeveral molecular subtypes of sporadic Creutzfeldt-Jakob disease have been identified and electroencephalogram and cerebrospinal fluid biomarkers have been reported to support clinical diagnosis but with variable utility according to subtype. In recent years, a series of publications

Preparation of SiO2-KCoFC composite ion-exchanger for removal of Cs in the soil decontamination waste solution

International Nuclear Information System (INIS)

Lee, Jung Joon; Moon, Jei kwon; Lee, Kune Woo

2009-01-01

The soil decontamination process has been developed for remediate the soil wastes excavated from the TRIGA research reactor sites. Even though the process was proven to be very effective for decontaminate the radioactive nuclides such as cesium and cobalt, the secondary spent solution should be treated with an appropriate method to minimize the waste volume. There are mainly two components in the spent decontamination solution of Cs and Co. The Co in the waste solution can be removed easily by precipitation under a basic condition. However, since the Cs is hardly removed by precipitation, an appropriate selective removal method should be employed. In this study, an inorganic composite ion exchanger of SiO 2 -KCoFC was prepared by sol-gel method for a removal of Cs in the decontamination waste solution. An optimum condition for a preparation of the composite ion exchanger and the adsorption performances of the prepared composite ion exchangers were evaluated

Comparison of a new global empirical ion composition model with available satellite data

Czech Academy of Sciences Publication Activity Database

Truhlík, Vladimír; Třísková, Ludmila; Šmilauer, Jan; Iwamoto, I.

2003-01-01

Roč. 31, č. 3 (2003), s. 665-675 ISSN 0273-1177 R&D Projects: GA ČR GP205/02/P037; GA AV ČR IAA3042201; GA AV ČR IAB3042104 Institutional research plan: CEZ:AV0Z3042911 Keywords : satellite data * ion composition model * outer ionosphere Subject RIV: DG - Athmosphere Sciences, Meteorology Impact factor: 0.483, year: 2003

Sporadic E S Layers at High Latitudes During a Magnetic Storm of March 17, 2015 According to the Vertical and Oblique Ionospheric Sounding Data

Science.gov (United States)

Blagoveshchensky, D. V.; Maltseva, O. A.; Anishin, M. M.; Rogov, D. D.

2017-11-01

We consider the behavior of the parameters of the ionospheric E s layers according to the vertical sounding at the Sodankylä observatory and oblique sounding at the Lovozero (Murmansk region)—Gor'kovskaya station (Leningrad region) path during a superstorm of March 17, 2015. Temporal and spatial behavior of these parameters is compared. It was found that the storm significantly distorted the normal course of variations of the sporadic E s layer characteristics. Specific behavior of the layers during a storm at points separated by about 300 km was detected. With the help of ray tracing calculations using the IRI model, oblique sounding ionograms were constructed for the radio path analyzed. Primary attention is given to the maximum usable frequency of the F 2 layer—MUF- F 2. Additionally, for the disturbed conditions where there is only a high-power E s layer on the experimental ionograms, the values of MUF- E s and the ratio K =MUF- E s/ f o E s for various cutoff frequencies f o E s of the E s layer and its altitudes {h}_{E_s} are calculated within the framework of the well-known approximations. Calculations for the case of weak disturbance and semitransparent E s layers are carried out with the IRI model adapted to the current diagnostics parameters. It was found that the calculated and experimental values of MUF- F 2 are close to each other or coincide, while this cannot be said about MUF- E s. The calculated and experimental values of MUF- E s can be matched in the model of mirror reflection from a flat layer for intense layers and the model of the E layer for thick E s layers of low intensity.

E1-forbidden transition rates in ions of astrophysical interest

International Nuclear Information System (INIS)

Träbert, E

2014-01-01

Transition rates in atomic systems may appear to be of little importance in steady-state plasmas that are observed at great distances from Earth. However, some of the transition rates compete with collision rates, and in these cases certain line intensity ratios are affected and can serve as remote indicators of density. In the low-density environments of stellar coronae and planetary nebulae, the transition rates of interest are mostly spin-forbidden E1 decays, higher-multipole order transitions (M1, E2, M2, M3), and hyperfine-induced transitions. On Earth, measurements of the long upper level lifetimes of these atomic systems require the use of ion traps. A fair number of test cases with lifetimes in the range from nanoseconds to many seconds have been treated successfully, and the evolution of calculations along with the experimental progress is notable. A new generation of cold ion traps is expected to extend the atomic lifetime measurements on multiply charged ions into the range of many minutes. (paper)

High Performance Li4Ti5O12/Si Composite Anodes for Li-Ion Batteries

Directory of Open Access Journals (Sweden)

Chunhui Chen

2015-08-01

Full Text Available Improving the energy capacity of spinel Li4Ti5O12 (LTO is very important to utilize it as a high-performance Li-ion battery (LIB electrode. In this work, LTO/Si composites with different weight ratios were prepared and tested as anodes. The anodic and cathodic peaks from both LTO and silicon were apparent in the composites, indicating that each component was active upon Li+ insertion and extraction. The composites with higher Si contents (LTO:Si = 35:35 exhibited superior specific capacity (1004 mAh·g−1 at lower current densities (0.22 A·g−1 but the capacity deteriorated at higher current densities. On the other hand, the electrodes with moderate Si contents (LTO:Si = 50:20 were able to deliver stable capacity (100 mAh·g−1 with good cycling performance, even at a very high current density of 7 A·g−1. The improvement in specific capacity and rate performance was a direct result of the synergy between LTO and Si; the former can alleviate the stresses from volumetric changes in Si upon cycling, while Si can add to the capacity of the composite. Therefore, it has been demonstrated that the addition of Si and concentration optimization is an easy yet an effective way to produce high performance LTO-based electrodes for lithium-ion batteries.

Ion conducting polymers and polymer blends for alkali metal ion batteries

Science.gov (United States)

DeSimone, Joseph M.; Pandya, Ashish; Wong, Dominica; Vitale, Alessandra

2017-08-29

Electrolyte compositions for batteries such as lithium ion and lithium air batteries are described. In some embodiments the compositions are liquid compositions comprising (a) a homogeneous solvent system, said solvent system comprising a perfluropolyether (PFPE) and polyethylene oxide (PEO); and (b) an alkali metal salt dissolved in said solvent system. In other embodiments the compositions are solid electrolyte compositions comprising: (a) a solid polymer, said polymer comprising a crosslinked product of a crosslinkable perfluropolyether (PFPE) and a crosslinkable polyethylene oxide (PEO); and (b) an alkali metal ion salt dissolved in said polymer. Batteries containing such compositions as electrolytes are also described.

Structure of Ion Outflow in the Martian Magnetotail

Science.gov (United States)

McFadden, J. P.; Mitchell, D.; Luhmann, J. G.; Connerney, J. E. P.; Jakosky, B. M.

2017-12-01

The Suprathermal And Thermal Ion Composition (STATIC) sensor on the MAVEN spacecraft provides a detailed look at the structure of ion outflow in the Martian magnetotail including ion composition, energization, and flow. Mars' magnetotail contains a mixture of cold (multi-species ions, tailward-moving cold multi-species ions, suprathermal ions of a few tens of eV, warm (about 100 eV) proton populations, and heavy (primarily O+) pickup ions at energies from 1 to 10 keV which may display several simultaneous peaks in energy flux. The cold tailward-moving ions represent a significant fraction of the Martian ion loss, perhaps comparable to loses from molecular oxygen dissociation. The suprathermal tail that accompanies the cold ions varies greatly and provides clues to ion escape. The warm protons, on first examination, appear to be of sheath origin, displaying a similar energy distribution and accompanied by a tenuous warm population at M/Q=2 (which could be either solar wind alphas or molecular hydrogen ions of ionospheric origin). STATIC produces a weak ghost peak at M/Q=11-12 when observing molecular hydrogen ions, but not alphas, often allowing the instrument to distinguish the source of protons. Measurements show the warm protons are of ionospheric origin in the central tail and transition to sheath plasma in the umbra. Energetic (1-10 keV) pickup oxygen in the magnetotail is produced on the nightside, near the pole where the IMF convection electric field points toward the planet, the same hemisphere where sputtering occurs. When two spectral peaks are observed, these tailward-moving ions differ in direction by relatively small angles (about 20 degrees). These peaks can persist for tens of minutes indicating approximately time-stationary acceleration, and therefore acceleration in potential fields. Magnetotail structure and geometry can be inferred not only from the local magnetic field, but also from the measured electron distributions which indicate source

Free-standing and bendable carbon nanotubes/TiO2 nanofibres composite electrodes for flexible lithium ion batteries

International Nuclear Information System (INIS)

Zhang, Peng; Qiu, Jingxia; Zheng, Zhanfeng; Liu, Gao; Ling, Min; Martens, Wayde; Wang, Haihui; Zhao, Huijun; Zhang, Shanqing

2013-01-01

Carbon nanotube (CNT) and TiO 2 nanofibre composite films are prepared and used as anode materials for lithium ion batteries (LIBs) without the use of binders and conventional copper current collector. The preliminary experimental results from X-ray diffraction, scanning electron microscopy and transmission electron microscopy suggest that the TiO 2 nanofibres were well-dispersed and interwoven by the CNTs, forming freestanding, bendable and light weighted composite. In comparison with TiO 2 nanofibre based LIBs, the CNTs could significantly improve the battery performance due to their high conductivity property and 3D network morphology. In both 1–3 V and 0.01–3 V testing voltage ranges, the as-prepared composites show excellent reversible capacity and capacity retention. The superior lithium storage capacity of the CNT/TiO 2 composite was mainly attributed to dual functions of the CNTs – the CNTs not only provide conductive networks to assist the electron transfer but also facilitate lithium ion diffusion between the electrolyte and the TiO 2 active materials by preventing agglomeration of TiO 2 nanofibres. This work demonstrates that the CNT–TiO 2 composite film could be one type of potential electrode material for large-scale LIB applications

Imaging movement-related activity in medicated Parkin-associated and sporadic Parkinson's disease

DEFF Research Database (Denmark)

van Eimeren, Thilo; Binkofski, Ferdinand; Buhmann, Carsten

2010-01-01

Treatment-related motor complications such as dyskinesias are a major problem in the long-term management of Parkinson's disease (PD). In sporadic PD, a relatively early onset of the disease is known to be associated with an early development of dyskinesias. Although linked with early onset...... selected movements. Patients with Parkin-associated and sporadic PD showed no difference in movement-related activation patterns. Moreover, the covariates 'age' and 'disease duration' similarly influenced brain activation in both patient groups. The present finding suggests that a stable long-term motor...

The Magnetic Properties of Metal-Alloy Glass Composites Prepared by Ion Implantation

International Nuclear Information System (INIS)

Julian Fernandez, Cesar de; Mattei, Giovanni; Sada, Cinzia; Maurizio, Chiara; Padovani, Sara; Mazzoldi, Paolo; Sangregorio, Claudio; Gatteschi, Dante

2003-01-01

The structural and magnetic properties of Co-Ni, Co-Fe and Ni-Cu alloy nanoparticles formed in silica matrix by sequential ion implantation are presented. These nanoparticles show crystal structure similar to the corresponding bulk alloys. In the Co-Ni and Co-Fe, magnetization saturation and coercive field depend on the the alloy composition, crystal structure and size effects. Ferromagnetic resonance studies show that collective magnetic processes are present and these are determined by the film-like morphology of the implanted region. The temperature dependence of the magnetization of the NixCu100-x samples indicates that their Curie Temperatures are larger than the corresponding bulk ones. This feature is discussed considering the composition of the nanoparticles and the size effects

Application of quantitative DTI metrics in sporadic CJD

Directory of Open Access Journals (Sweden)

E. Caverzasi

2014-01-01

Full Text Available Diffusion Weighted Imaging is extremely important for the diagnosis of probable sporadic Jakob–Creutzfeldt disease, the most common human prion disease. Although visual assessment of DWI MRI is critical diagnostically, a more objective, quantifiable approach might more precisely identify the precise pattern of brain involvement. Furthermore, a quantitative, systematic tracking of MRI changes occurring over time might provide insights regarding the underlying histopathological mechanisms of human prion disease and provide information useful for clinical trials. The purposes of this study were: 1 to describe quantitatively the average cross-sectional pattern of reduced mean diffusivity, fractional anisotropy, atrophy and T1 relaxation in the gray matter (GM in sporadic Jakob–Creutzfeldt disease, 2 to study changes in mean diffusivity and atrophy over time and 3 to explore their relationship with clinical scales. Twenty-six sporadic Jakob–Creutzfeldt disease and nine control subjects had MRIs on the same scanner; seven sCJD subjects had a second scan after approximately two months. Cortical and subcortical gray matter regions were parcellated with Freesurfer. Average cortical thickness (or subcortical volume, T1-relaxiation and mean diffusivity from co-registered diffusion maps were calculated in each region for each subject. Quantitatively on cross-sectional analysis, certain brain regions were preferentially affected by reduced mean diffusivity (parietal, temporal lobes, posterior cingulate, thalamus and deep nuclei, but with relative sparing of the frontal and occipital lobes. Serial imaging, surprisingly showed that mean diffusivity did not have a linear or unidirectional reduction over time, but tended to decrease initially and then reverse and increase towards normalization. Furthermore, there was a strong correlation between worsening of patient clinical function (based on modified Barthel score and increasing mean diffusivity.

Streptococcus mutans-induced secondary caries adjacent to glass ionomer cement, composite resin and amalgam restorations in vitro Cárie secundária adjacente a restaurações de cimento de ionômero de vidro, resina composta e amálgama induzida por Streptococcus mutans in vitro

Directory of Open Access Journals (Sweden)

Adriana Gama-Teixeira

2007-12-01

Full Text Available The aim of this study was to define, in vitro, the potential to inhibit secondary caries of restorative materials currently used in dental practice. Standard cavities were prepared on the buccal and lingual surfaces of fifty extracted human third molars. The teeth were randomly divided into five groups, each one restored with one of the following materials: glass ionomer cement (GIC; amalgam; light-cured composite resin; ion-releasing composite; and light-cured, fluoride-containing composite resin. The teeth were thermocycled, sterilized with gamma irradiation, exposed to a cariogenic challenge using a bacterial system using Streptococcus mutans, and then prepared for microscopic observation. The following parameters were measured in each lesion formed: extension, depth, and caries inhibition area. The outer lesions developed showed an intact surface layer and had a rectangular shape. Wall lesions were not observed inside the cavities. After Analysis of Variance and Component of Variance Models Analysis, it was observed that the GIC group had the smallest lesions and the greatest number of caries inhibition areas. The lesions developed around Amalgam and Ariston pHc restorations had an intermediate size and the largest lesions were observed around Z-100 and Heliomolar restorations. It may be concluded that the restorative materials GIC, amalgam and ion-releasing composites may reduce secondary caries formation.O objetivo deste estudo foi definir, in vitro, o potencial de materiais restauradores, usados rotineiramente na prática clínica, na inibição da cárie secundária. Cavidades padronizadas foram preparadas nas faces vestibulares e linguais de 50 terceiros molares humanos extraídos. Os dentes foram divididos aleatoriamente em 5 grupos, cada um restaurado com um dos seguintes materiais: cimento de ionômero de vidro (CIV; amálgama; resina composta fotopolimerizável; compósito que libera íons, e resina composta fotopolimeriz

Production of composite neutral Higgs bosons in photoproduction and e+e- experiments

International Nuclear Information System (INIS)

Whisnant, K.; Young, B.; Hu, S.

1985-01-01

We examine the consequences of a sizable tree-level coupling of a neutral Higgs boson to two photons, which could exist in composite models where the intermediate vector bosons and scalar Higgs bosons are made of the same subconstituents. We find that for certain ranges of the coupling strength and Higgs-boson mass, a neutral composite Higgs boson can be produced and detected in photon-proton scattering and e + e - annihilation at currently accessible energies. We also discuss other processes that are not present in the standard model at the tree level, but may lead to observable neutral-Higgs-boson production at, for instance, a p-barp collider

Transmission of sporadic Creutzfeldt-Jakob disease by blood transfusion: risk factor or possible biases.

Science.gov (United States)

Puopolo, Maria; Ladogana, Anna; Vetrugno, Vito; Pocchiari, Maurizio

2011-07-01

The occurrence of transfusion transmissions of variant Creutzfeldt-Jakob disease (CJD) cases has reawakened attention to the possible similar risk posed by other forms of CJD. CJD with a definite or probable diagnosis (sporadic CJD, n = 741; genetic CJD, n = 175) and no-CJD patients with definite alternative diagnosis (n = 482) with available blood transfusion history were included in the study. The risk of exposure to blood transfusion occurring more than 10 years before disease onset and for some possible confounding factors was evaluated by calculating crude odds ratios (ORs). Variables with significant ORs in univariate analyses were included in multivariate logistic regression analyses. In the univariate model, blood transfusion occurring more than 10 years before clinical onset is 4.1-fold more frequent in sporadic CJD than in other neurologic disorders. This significance is lost when the 10-year lag time was not considered. Multivariate analyses show that the risk of developing sporadic CJD after transfusion increases (OR, 5.05) after adjusting for possible confounding factors. Analysis conducted on patients with genetic CJD did not reveal any significant risk factor associated with transfusion. This is the first case-control study showing a significant risk of transfusion occurring more than 10 years before clinical onset in sporadic CJD patients. It remains questionable whether the significance of these data is biologically plausible or the consequence of biases in the design of the study, but they counterbalance previous epidemiologic negative reports that might have overestimated the assessment of blood safety in sporadic CJD. © 2010 American Association of Blood Banks.

Study on performance of composite polymer films doped with modified molecular sieve for lithium-ion batteries

International Nuclear Information System (INIS)

Zhang Yuqing; Zhang Guodong; Du Tingdong; Zhang Lizao

2010-01-01

To improve the tensile strength and ionic conductivity of composite polymer films for lithium-ion batteries, molecular sieves of MCM-41 modified with sulfated zirconia (SO 4 2- /ZrO 2 , SZ), denoted as MCM-41/SZ, were doped into a poly(vinylidene fluoride) (PVdF) matrix to fabricate MCM-41/SZ composite polymer films, denoted as MCM-41/SZ films. Examination by transmission electron microscope (TEM) shows that modified molecular sieves have lower aggregation and a more porous structure. Tensile strength tests were carried out to investigate the mechanical performance of MCM-41/SZ films, and then the electrochemical performance of batteries with MCM-41/SZ films as separators was tested. The results show that the tensile strength (σ t ) of MCM-41/SZ film was up to 7.8 MPa; the ionic conductivity of MCM-41/SZ film was close to 10 -3 S cm -1 at room temperature; and the coulombic efficiency of the assembled lithium-ion battery was 92% at the first cycle and reached as high as 99.99% after the 20th cycle. Meanwhile, the charge-discharge voltage plateau of the lithium-ion battery presented a stable state. Therefore, MCM-41/SZ films are a good choice as separators for lithium-ion batteries due to their high tensile strength and ionic conductivity.

Swift heavy ion irradiation induced phase transformation in undoped and niobium doped titanium dioxide composite thin films

Energy Technology Data Exchange (ETDEWEB)

Gautam, Subodh K., E-mail: subodhkgtm@gmail.com [Inter University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110 067 (India); Chettah, Abdelhak [LGMM Laboratory, Université 20 Août 1955-Skikda, BP 26, 21000 Skikda (Algeria); Singh, R.G. [Department of Physics, Bhagini Nivedita College, Delhi University, Delhi 110043 (India); Ojha, Sunil; Singh, Fouran [Inter University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110 067 (India)

2016-07-15

Study reports the effect of swift heavy ion (SHI) irradiation induced phase transformation in undoped and Niobium doped anatase TiO{sub 2} composite thin films. Investigations were carried out at different densities of electronic excitations (EEs) using 120 MeV Ag and 130 MeV Ni ions irradiations. Films were initially annealed at 900 °C and results revealed that undoped films were highly stable in anatase phase, while the Nb doped films showed the composite nature with the weak presence of Niobium penta-oxide (Nb{sub 2}O{sub 5}) phase. The effect at low density of EEs in undoped film show partial anatase to rutile phase transformation; however doped film shows only further growth of Nb{sub 2}O{sub 5} phase beside the anatase to rutile phase transformation. At higher density of EEs induced by Ag ions, registered continuous ion track of ∼3 nm in lattice which leads to nano-crystallization followed by decomposition/amorphization of rutile TiO{sub 2} and Nb{sub 2}O{sub 5} phases in undoped and doped films, respectively. However, Ni ions are only induced discontinuous sequence of ion tracks with creation of damage and disorder and do not show amorphization in the lattice. The in-elastic thermal spike calculations were carried out for anatase TiO{sub 2} phase to understand the effect of EEs on anatase to rutile phase transformation followed by amorphization in NTO films in terms of continuous and discontinuous track formation by SHI irradiation.

Principles of fuel ion ratio measurements in fusion plasmas by collective Thomson scattering

DEFF Research Database (Denmark)

Stejner Pedersen, Morten; Nielsen, Stefan Kragh; Bindslev, Henrik

2011-01-01

ratio. Measurements of the fuel ion ratio will be important for plasma control and machine protection in future experiments with burning fusion plasmas. Here we examine the theoretical basis for fuel ion ratio measurements by CTS. We show that the sensitivity to plasma composition is enhanced......For certain scattering geometries collective Thomson scattering (CTS) measurements are sensitive to the composition of magnetically confined fusion plasmas. CTS therefore holds the potential to become a new diagnostic for measurements of the fuel ion ratio—i.e. the tritium to deuterium density...... by the signatures of ion cyclotron motion and ion Bernstein waves which appear for scattering geometries with resolved wave vectors near perpendicular to the magnetic field. We investigate the origin and properties of these features in CTS spectra and give estimates of their relative importance for fuel ion ratio...

Fundamental aspects on ion-beam surface modification: defect production and migration processes

International Nuclear Information System (INIS)

Rehn, L.E.; Averback, R.S.; Okamoto, P.R.

1984-09-01

Ion-beam modification of metals is generating increasing scientific interest not only because it has exciting technological potential, but also because it has raised fundamental questions concerning radiation-induced diffusion processes. In addition to the implanted species, several defect production and migration mechanisms contribute to changes in the near-surface composition of an alloy during ion bombardment, e.g., atoms exchange positions via displacements and replacement sequences; preferential sputtering effects arise; radiation-enhanced diffusion and radiation-induced segregation occur. The latter two defect migration mechanisms are of particular significance since they can alter the composition to depths which are much greater than the implanted ion range. By altering various parameters such as irradiation temperature, ion mass, energy, and current density, and initial alloying distributions, a rich variety of near-surface composition profiles can be created. We have utilized changes in ion mass and energy, and irradiation temperature to distinguish defect production from defect migration effects. Experimental results are presented which provide a guide to the relative efficiencies of different mechanisms under various irradiation conditions. 46 references

Surface plasmon resonance sensing detection of mercury and lead ions based on conducting polymer composite.

Directory of Open Access Journals (Sweden)

Mahnaz M Abdi

Full Text Available A new sensing area for a sensor based on surface plasmon resonance (SPR was fabricated to detect trace amounts of mercury and lead ions. The gold surface used for SPR measurements were modified with polypyrrole-chitosan (PPy-CHI conducting polymer composite. The polymer layer was deposited on the gold surface by electrodeposition. This optical sensor was used for monitoring toxic metal ions with and without sensitivity enhancement by chitosan in water samples. The higher amounts of resonance angle unit (ΔRU were obtained for PPy-CHI film due to a specific binding of chitosan with Pb(2+ and Hg(2+ ions. The Pb(2+ ion bind to the polymer films most strongly, and the sensor was more sensitive to Pb(2+ compared to Hg(2+. The concentrations of ions in the parts per million range produced the changes in the SPR angle minimum in the region of 0.03 to 0.07. Data analysis was done by Matlab software using Fresnel formula for multilayer system.

Iron-Based Nanomaterials/Graphene Composites for Advanced Electrochemical Sensors

Directory of Open Access Journals (Sweden)

Kaveh Movlaee

2017-11-01

Full Text Available Iron oxide nanostructures (IONs in combination with graphene or its derivatives—e.g., graphene oxide and reduced graphene oxide—hold great promise toward engineering of efficient nanocomposites for enhancing the performance of advanced devices in many applicative fields. Due to the peculiar electrical and electrocatalytic properties displayed by composite structures in nanoscale dimensions, increasing efforts have been directed in recent years toward tailoring the properties of IONs-graphene based nanocomposites for developing more efficient electrochemical sensors. In the present feature paper, we first reviewed the various routes for synthesizing IONs-graphene nanostructures, highlighting advantages, disadvantages and the key synthesis parameters for each method. Then, a comprehensive discussion is presented in the case of application of IONs-graphene based composites in electrochemical sensors for the determination of various kinds of (biochemical substances.

Iron-Based Nanomaterials/Graphene Composites for Advanced Electrochemical Sensors

Science.gov (United States)

Movlaee, Kaveh; Ganjali, Mohmmad Reza; Norouzi, Parviz

2017-01-01

Iron oxide nanostructures (IONs) in combination with graphene or its derivatives—e.g., graphene oxide and reduced graphene oxide—hold great promise toward engineering of efficient nanocomposites for enhancing the performance of advanced devices in many applicative fields. Due to the peculiar electrical and electrocatalytic properties displayed by composite structures in nanoscale dimensions, increasing efforts have been directed in recent years toward tailoring the properties of IONs-graphene based nanocomposites for developing more efficient electrochemical sensors. In the present feature paper, we first reviewed the various routes for synthesizing IONs-graphene nanostructures, highlighting advantages, disadvantages and the key synthesis parameters for each method. Then, a comprehensive discussion is presented in the case of application of IONs-graphene based composites in electrochemical sensors for the determination of various kinds of (bio)chemical substances. PMID:29168771

Gastric Medullary Carcinoma with Sporadic Mismatch Repair Deficiency and a TP53 R273C Mutation: An Unusual Case with Wild-Type BRAF

Directory of Open Access Journals (Sweden)

Brett M. Lowenthal

2017-01-01

Full Text Available Medullary carcinoma has long been recognized as a subtype of colorectal cancer associated with microsatellite instability and Lynch syndrome. Gastric medullary carcinoma is a very rare neoplasm. We report a 67-year-old male who presented with a solitary gastric mass. Total gastrectomy revealed a well-demarcated, poorly differentiated carcinoma with an organoid growth pattern, pushing borders, and abundant peritumoral lymphocytic response. The prior cytology was cellular with immunohistochemical panel consistent with upper gastrointestinal/pancreaticobiliary origin. Overall, the histopathologic findings were consistent with gastric medullary carcinoma. A mismatch repair panel revealed a mismatch repair protein deficient tumor with loss of MLH1 and PMS2 expression. BRAF V600E immunostain (VE1 and BRAF molecular testing were negative, indicating a wild-type gene. Tumor sequencing of MLH1 demonstrated a wild-type gene, while our molecular panel identified TP53 c.817C>T (p.R273C mutation. These findings were compatible with a sporadic tumor. Given that morphologically identical medullary tumors often occur in Lynch syndrome, it is possible that mismatch repair loss is an early event in sporadic tumors with p53 mutation being a late event. Despite having wild-type BRAF, this tumor is sporadic and unrelated to Lynch syndrome. This case report demonstrates that coordinate ancillary studies are needed to resolve sporadic versus hereditary rare tumors.

Comparison of (e,2e), photoelectron and conventional spectroscopies for the Ar2 ion

International Nuclear Information System (INIS)

McCarthy, I.E.; Uylings, P.; Poppe, R.

1978-05-01

States of the Ar2 ion whose eigenvectors contain large components of single-hole configurations are observed in the (e,2e) and (γ,e) reactions on the Ar1 atom. The cross section is regarded as being proportional to the spectroscopic factor, that is the state expectation value of the single-hole configuration in the eigenvector. State expectation values obtained from these reactions for 1/2 + states are compared with ones obtained by diagonalizing an effective hamiltonian in a model space, with radial matrix elememts determined by fitting spectra for bound states. (e,2e) and conventional spectroscopy are compatible and provide complementary information about structure. Simple analysis of present (γ,e) data does not lead to compatible information on spectroscopic factors

Near Earth space sporadic radio emission busts occurring during sunrise

Science.gov (United States)

Dudnik, A. V.; Zaljubovsky, I. I.; Kartashev, V. M.; Lasarev, A. V.; Shmatko, E. S.

1985-01-01

During the period of low solar activity at sunrise the effect of sporadic high frequency near Earth space radio emission was experimentally discovered at middle latitudes. The possible mechanism of its origin is discussed.

Kinetics of ion/molecule reactions in Xe++acteone system

International Nuclear Information System (INIS)

Vinogradov, P.S.; Misharin, A.S.

2002-01-01

A reaction of Xe+ ion with acetone and subsequent transformations of the product ions at a buffer gas pressure (He) of 1.1 Torr were studied by the flow reactor technique mass spectrometry. A kinetic scheme describing the evolution of the ionic composition has been determined. The rate constants of the key reactions involved in the scheme have been evaluated. A channel of the production of acetone cation in A state in a charge transfer reaction was observed. A production of slowly reacting isomer of the acetone cation in secondary reactions was detected. Its product in the reaction with acetone is the 'nonprotonated dimer'. The kinetics of the production of ternary ions - ( CH 3 CO + CH 3 COCH 3 )(m/e=101), CH 3 COCH 3 H + (m/e=59) as well as the production of ions of the fourth generation ( CH 3 CO + (CH 3 COCH 3 ) 2 ) (m/e=159) and (CH 3 COCH 3 ) 2 H + was observed. CH 3 CO + ion (m/e=43) was found as the main reaction product. The main pathways scheme of ionic transformations is shown. (nevyjel)

Oestrogen receptor beta isoform expression in sporadic colorectal cancer, familial adenomatous polyposis and progressive stages of colorectal cancer

DEFF Research Database (Denmark)

Stevanato Filho, Paulo Roberto; Aguiar Júnior, Samuel; Begnami, Maria Dirlei

2017-01-01

BACKGROUND: Among the sex hormones, oestrogen may play a role in colorectal cancer, particularly in conjunction with oestrogen receptor-β (ERβ). The expression of ERβ isoform variants and their correlations with familial adenomatous polyposis (FAP) syndrome and sporadic colorectal carcinomas...... was identified in sporadic polyps and in sporadic colorectal cancer as well as in polyps from FAP syndrome patients compared with normal tissues (p expression in polyps (p ..., no differences were observed when sporadic colorectal carcinomas were compared to normal mucosa tissues. These findings suggest an association of the ERβ isoform variants in individuals affected by germline mutations of the APC gene. Progressively decreased expression of ERβ was found in polyps at early stages...

Microwave Derived Facile Approach to Sn/Graphene Composite Anodes for, Lithium-Ion Batteries

International Nuclear Information System (INIS)

Beck, Faith R.; Epur, Rigved; Hong, Daeho; Manivannan, Ayyakkannu; Kumta, Prashant N.

2014-01-01

Graphical abstract: Tin particles embedded in graphene (G) sheet have been synthesized by microwave reduction of tin halide (SnCl 2 ) and graphite oxide (GO) followed by annealing in argon. The microwave reaction resulted in the formation of tin oxide embedded in graphene sheets. Annealing in argon at elevated temperatures initiated carbothermal reduction culminating in the formation of tin decorated graphene sheet composites that were employed as anodes for lithium-ion batteries. X-ray diffraction analysis of the final composite showed the presence of crystalline tin combined with a very small diffraction peak corresponding to (002) plane of graphite. Scanning electron microscopy (SEM) revealed decorated graphene layers with tin droplets. X-ray Photoelectron Spectroscopy (XPS) confirmed the presence of graphene and graphene oxide in the composite. Electrochemical cycling response indicated that the tin/graphene composite exhibited initial discharge capacities varying from 790 mAh/g to 850 mAh/g depending on the composition, while a stable reversible capacity of ∼500 mAh/g was achieved for optimized compositions when cycled at a current density of ∼100 mA/g in the voltage window of 0.02 to 1.2 V vs. Li + /Li. Carbon coating of the Sn/G composite ultimately achieved by decomposition of dextrose using microwave heating significantly improved the electrochemical cycling stability. - Highlights: • Tin embedded graphene sheets have been synthesized by microwave reduction. • Tin oxide and graphene formed was carbothermally reduced to Sn/graphene. • XPS confirmed presence of graphene and graphene oxide in the composite. • Electrochemical response indicated capacities in 790 mAh/g to 850 mAh/g range. • Carbon coated composite yielded stable reversible capacity ∼500 mAh/g. - Abstract: Tin particles embedded in graphene (G) sheets have been synthesized by microwave reduction of tin halide (SnCl 2 .2H 2 O) and graphite oxide (GO) followed by annealing in argon

Compositional and structural studies of ion-beam modified AlN/TiN multilayers

Energy Technology Data Exchange (ETDEWEB)

Amati, M., E-mail: matteo.amati@elettra.eu [Elettra – Sincrotrone Trieste SCpA,Area Science Park, 34149, Trieste (Italy); Gregoratti, L.; Sezen, H. [Elettra – Sincrotrone Trieste SCpA,Area Science Park, 34149, Trieste (Italy); Grce, A.; Milosavljević, M. [VINČA Institute of Nuclear Sciences, Belgrade University, P.O. Box 522, 11001, Belgrade (Serbia); Homewood, K.P. [Materials Research Institute and School of Physics and Astronomy, Queen Mary University of London, Mile End Road, E1 4NS, London (United Kingdom)

2017-07-31

Highlights: • Inter-layer mixing, atomic redistribution, structural change, and phase transformation on AlN/TiN multilayers via argon ion irradiation. • Severe modifications are observed with TEM studies on highly immiscible alternating layers without any side effects such as beam heating. • The original TiN layers appear to grow in thickness by consuming the adjacent AlN layers, while obtaining a better TiAlN fcc crystalline structure. • Photoemission spectroscopy/microscopy indicates a transformation into Al deficient ternary and highly homogeneous compounds on both layers. • These results can be interesting towards further development of radiation tolerant materials based on immiscible ceramic nanocomposites. - Abstract: This paper reports on compositional and structural modifications induced in coated AlN/TiN multilayers by argon ion irradiation. The initial structure consisting of totally 30 alternate AlN (8 nm thick) and TiN (9.3 nm thick) layers was deposited on Si (100) wafers, by reactive sputtering. Irradiation was done with 180 keV Ar{sup +} to a high dose of 8 × 10{sup 16} ions/cm{sup 2}, which introduces up to ∼10 at.% of argon species, and generates a maximum displacement per atom of 92 for AlN and 127 for TiN, around the projected ion range (109 ± 34 nm). Characterizations were performed by Rutherford backscattering spectrometry, spatially resolved x-ray photoelectron spectroscopy, and transmission electron microscopy. The obtained results reveal that this highly immiscible and thermally stable system suffered a severe modification upon the applied ion irradiation, although it was performed at room temperature. They illustrate a thorough inter-layer mixing, atomic redistribution, structural change and phase transformation within the affected depth. The original TiN layers appear to grow in thickness, consuming the adjacent AlN layers, while retaining the fcc crystalline structure. In the mostly affected region, the interaction proceeds

Surface composition of biomedical components by ion beam analysis

International Nuclear Information System (INIS)

Kenny, M.J.; Wielunski, L.S.; Baxter, G.R.

1991-01-01

Materials used for replacement body parts must satisfy a number of requirements such as biocompatibility and mechanical ability to handle the task with regard to strength, wear and durability. When using a CVD coated carbon fibre reinforced carbon ball, the surface must be ion implanted with uniform dose of nitrogen ions in order to make it wear resistant. The mechanism by which the wear resistance is improved is one of radiation damage and the required dose of about 10 16 cm -2 can have a tolerance of about 20%. To implant a spherical surface requires manipulation of the sample within the beam and control system (either computer or manually operated) to enable uniform dose all the way from polar to equatorial regions on the surface. A manipulator has been designed and built for this purpose. In order to establish whether the dose is uniform, nuclear reaction analysis using the reaction 14 N(d,α) 12 C is an ideal method of profiling. By taking measurements at a number of points on the surface, the uniformity of nitrogen dose can be ascertained. It is concluded that both Rutherford Backscattering and Nuclear Reaction Analysis can be used for rapid analysis of surface composition of carbon based materials used for replacement body components. 2 refs., 2 figs

Influence of Coding Variability in APP-Aβ Metabolism Genes in Sporadic Alzheimer's Disease.

Directory of Open Access Journals (Sweden)

Celeste Sassi

Full Text Available The cerebral deposition of Aβ42, a neurotoxic proteolytic derivate of amyloid precursor protein (APP, is a central event in Alzheimer's disease (AD(Amyloid hypothesis. Given the key role of APP-Aβ metabolism in AD pathogenesis, we selected 29 genes involved in APP processing, Aβ degradation and clearance. We then used exome and genome sequencing to investigate the single independent (single-variant association test and cumulative (gene-based association test effect of coding variants in these genes as potential susceptibility factors for AD, in a cohort composed of 332 sporadic and mainly late-onset AD cases and 676 elderly controls from North America and the UK. Our study shows that common coding variability in these genes does not play a major role for the disease development. In the single-variant association analysis, the main hits, none of which statistically significant after multiple testing correction (1.9e-4e-3 sporadic AD.

Dual infection with hepatitis A and E viruses in outbreaks and in sporadic clinical cases: Cuba 1998-2003.

Science.gov (United States)

Rodríguez Lay, Licel de los Angeles; Quintana, Ariel; Villalba, María Caridad Montalvo; Lemos, Gilda; Corredor, Marité Bello; Moreno, Aidonis Gutiérrez; Prieto, Pablo Aguiar; Guzmán, María G; Anderson, David

2008-05-01

Viral hepatitis ranks as the fifth cause of morbidity for infectious diseases in Cuba. Epidemics are observed frequently in the population, the hepatitis A virus being the main agent responsible for such epidemics. Previous reports also confirmed the circulation of the hepatitis E virus. From 1998 to 2003, 258 serum samples were collected by the Reference Laboratory on Viral Hepatitis during 33 outbreaks of acute viral hepatitis as well as from 39 sporadic clinical cases. Sera were tested for anti-HAV and anti-HEV IgM by EIA. Overall of the 33 outbreaks studied sera from 12 (36.4%) were positive for anti-HAV IgM only, from 7 (21.2%) were positive for anti-HEV IgM only, and from 14 (42.4%) were positive for antibodies to both viruses. Individually of the 258 sera collected, 137 (53.1%) were positives for anti-HAV IgM, 20 (7.8%) were positives for anti-HEV IgM, 33 (12.8%) were positives for both markers and 68 (26.4%) were negative to both. Of the clinical cases, 4 (10.3%) were positives for anti-HAV IgM, 13 (33.3%) were positives for anti-HEV IgM and 5 (12.8%) were positives for both markers. Seventeen (43.6%) sera were negatives for all viral hepatitis markers available (A-E). A high positivity for HEV was found in outbreaks tested with the kit produced by CIGB. In particular HEV seems to infect individuals of all ages. The results demonstrate the co-circulation of and co-infection with two enterically transmitted viruses; however a higher positivity was observed for anti-HAV than to anti-HEV (53.1% vs. 7.8%) in outbreaks.

Ion-beam-induced topography and compositional changes in depth profiling

International Nuclear Information System (INIS)

Carter, G.; Nobes, M.J.

1992-01-01

When energetic ions penetrate and stop in solids they not only add a new atomic constituent to the matrix but they also create atomic recoils and defects. The fluxes of these entities can give rise to spatial redistribution of atomic components, which may be partly or completely balanced by reordering and relaxation processes. These latter, in turn, may be influenced by fields and gradients induced by the primary relocation processes and by the energy deposited. These will include quasi-thermal, concentration (or chemical potential) and electrostatic gradients and may act to enhance or suppress atomic redistribution. Some, or all, of these processes will operate, depending upon the system under study, when energetic ions are employed to sputter erode a substrate for depth sectioning and, quite generally, can perturb the atomic depth profile that it is intended to evaluate. Theoretical and computational approaches to modelling such processes will be outlined and experimental examples shown which illustrate specific phenomena. In particular the accumulation of implant species and defect generation or redistribution can modify, with increasing ion fluence, the local sputtering mechanism and create further problems in depth profile analysis as a changing surface topography penetrates the solid. Examples of such topographic evolution and its influence on depth profiling analysis will be given and models to explain general and specific behaviour will be outlined. The commonality of models which examine both depth-dependent composition modification and surface topography evolution will be stressed. (author)

Microsatellite D21D210 (GT-12) allele frequencies in sporadic Alzheimer's disease

International Nuclear Information System (INIS)

Lannfelt, L.; Lilius, L.; Viitanen, M.; Winblad, B.; Basun, H.; Houlden, H.; Rossor, M.; Hardy, J.

1995-01-01

Four disease-causing mutations have so far been described in the amyloid precursor protein gene on chromosome 21 in familial early-onset Alzheimer's disease. Linkage analysis with a fourteen-allele microsatellite at D21S210 named GT-12 has proven useful in the elucidation of amyloid presursor protein gene involvement in Alzheimer's disease families, as it is closely linked to the gene. Most cases of Alzheimer's disease are thought to be sporadic and not familial. However, evidence from earlier studies suggests an important genetic contribution also in sporadic cases, where gene-environment interaction may contribute to the disease. We have determined frequencies of the GT-12 alleles in 78 Swedish and 49 British sporadic Alzheimer's disease cases and 104 healthy elderly control subjects, to investigate if the disease associates with a particular genotype in GT-12. However, no differences in allele frequencies were observed between any of the groups. (au) (26 refs.)

Mutation analysis of SDHB and SDHC: novel germline mutations in sporadic head and neck paraganglioma and familial paraganglioma and/or pheochromocytoma

Directory of Open Access Journals (Sweden)

Wong Nora

2006-01-01

Full Text Available Abstract Background Germline mutations of the SDHD, SDHB and SDHC genes, encoding three of the four subunits of succinate dehydrogenase, are a major cause of hereditary paraganglioma and pheochromocytoma, and demonstrate that these genes are classic tumor suppressors. Succinate dehydrogenase is a heterotetrameric protein complex and a component of both the Krebs cycle and the mitochondrial respiratory chain (succinate:ubiquinone oxidoreductase or complex II. Methods Using conformation sensitive gel electrophoresis (CSGE and direct DNA sequencing to analyse genomic DNA from peripheral blood lymphocytes, here we describe the mutation analysis of the SDHB and SDHC genes in 37 patients with sporadic (i.e. no known family history head and neck paraganglioma and five pheochromocytoma and/or paraganglioma families. Results Two sporadic patients were found to have a SDHB splice site mutation in intron 4, c.423+1G>A, which produces a mis-spliced transcript with a 54 nucleotide deletion, resulting in an 18 amino acid in-frame deletion. A third patient was found to carry the c.214C>T (p.Arg72Cys missense mutation in exon 4 of SDHC, which is situated in a highly conserved protein motif that constitutes the quinone-binding site of the succinate: ubiquinone oxidoreductase (SQR complex in E. coli. Together with our previous results, we found 27 germline mutations of SDH genes in 95 cases (28% of sporadic head and neck paraganglioma. In addition all index patients of five families showing hereditary pheochromocytoma-paraganglioma were found to carry germline mutations of SDHB: four of which were novel, c.343C>T (p.Arg115X, c.141G>A (p.Trp47X, c.281G>A (p.Arg94Lys, and c.653G>C (p.Trp218Ser, and one reported previously, c.136C>T, p.Arg46X. Conclusion In conclusion, these data indicate that germline mutations of SDHB and SDHC play a minor role in sporadic head and neck paraganglioma and further underline the importance of germline SDHB mutations in cases of

60 keV Ar⁺-ion induced modification of microstructural, compositional, and vibrational properties of InSb

Energy Technology Data Exchange (ETDEWEB)

Datta, D. P.; Garg, S. K.; Som, T., E-mail: tsom@iopb.res.in [SUNAG Laboratory, Institute of Physics, Bhubaneswar, Odisha 751005 (India); Satpati, B. [Surface Physics and Materials Science Division, Saha Institute of Nuclear Physics, 1/AF Bidhannagar, Kolkata 700064 (India); Sahoo, P. K. [School of Physical Sciences, National Institute of Science Education and Research, Bhubaneswar 751005, Odisha (India); Kanjilal, A. [Department of Physics, Shiv Nadar University, Uttar Pradesh 203207 (India); Dhara, S. [Surface and Nanoscience Division, Materials Science Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India); Kanjilal, D. [Inter-University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India)

2014-10-14

Room temperature irradiation of InSb(111) by 60 keV Ar⁺-ions at normal (0°) and oblique (60°) angles of incidence led to the formation of nanoporous structure in the high fluence regime of 1×10¹⁷ to 3×10¹⁸ ions cm⁻². While a porous layer comprising of a network of interconnected nanofibers was generated by normal ion incidence, evolution of plate-like structures was observed for obliquely incident ions. Systematic studies of composition and structure using energy dispersive x-ray spectroscopy, Raman spectroscopy, x-ray photoelectron spectroscopy, Raman mapping, grazing incidence x-ray diffraction, and cross-sectional transmission electron microscopy revealed a high degree of oxidation of the ion-induced microstructures with the presence of In₂O₃ and Sb₂O₃ phases and presence of nanocrystallites within the nanoporous structures. The observed structural evolution was understood in terms of processes driven by ion-induced defect accumulation within InSb.

Cross-linked Composite Gel Polymer Electrolyte using Mesoporous Methacrylate-Functionalized SiO2 Nanoparticles for Lithium-Ion Polymer Batteries

Science.gov (United States)

Shin, Won-Kyung; Cho, Jinhyun; Kannan, Aravindaraj G.; Lee, Yoon-Sung; Kim, Dong-Won

2016-01-01

Liquid electrolytes composed of lithium salt in a mixture of organic solvents have been widely used for lithium-ion batteries. However, the high flammability of the organic solvents can lead to thermal runaway and explosions if the system is accidentally subjected to a short circuit or experiences local overheating. In this work, a cross-linked composite gel polymer electrolyte was prepared and applied to lithium-ion polymer cells as a safer and more reliable electrolyte. Mesoporous SiO2 nanoparticles containing reactive methacrylate groups as cross-linking sites were synthesized and dispersed into the fibrous polyacrylonitrile membrane. They directly reacted with gel electrolyte precursors containing tri(ethylene glycol) diacrylate, resulting in the formation of a cross-linked composite gel polymer electrolyte with high ionic conductivity and favorable interfacial characteristics. The mesoporous SiO2 particles also served as HF scavengers to reduce the HF content in the electrolyte at high temperature. As a result, the cycling performance of the lithium-ion polymer cells with cross-linked composite gel polymer electrolytes employing methacrylate-functionalized mesoporous SiO2 nanoparticles was remarkably improved at elevated temperatures. PMID:27189842

Studies on synthesis of some composites and their uses for cesium separation

International Nuclear Information System (INIS)

Someda, H.H.; El-Zahhar, A.A.; Shehata, M.K.K.; El-Naggar, H.A.

2002-01-01

In this study some composite sorbents were prepared by supporting hexacyanoferrate complexes of some transition metals like Co, Ni, Fe and Zn on some different solid supports e.g. cellulose and other natural materials as wood powder. These composites were used for cesium sorption and showed that the highest sorption capacity is for zinc composite and the lowest is for cobalt composite. Also the factors affecting the sorption capacity like acid concentration, competing ions and cesium ion concentration were studied. The release of the sorbed cesium from the composite materials was also studied under different concentrations of different solutions like sodium nitrate, silver nitrate, ammonium nitrate and a mixture of ammonium nitrate and silver nitrate solutions

Potential application of microporous structured poly(vinylidene fluoride-hexafluoropropylene)/poly(ethylene terephthalate) composite nonwoven separators to high-voltage and high-power lithium-ion batteries

International Nuclear Information System (INIS)

Jeong, Hyun-Seok; Choi, Eun-Sun; Kim, Jong Hun; Lee, Sang-Young

2011-01-01

Highlights: → Microporous-structured PVdF-HFP/PET composite nonwoven separators for Li-batteries. → Well-developed microporous structure and liquid electrolyte wettability. → Provision of facile ion transport and suppressed growth of cell impedance. → Superior cell performance at high-voltages/high-current densities. - Abstract: We demonstrate potential application of a new composite non-woven separator, which is comprised of a phase inversion-controlled, microporous polyvinylidene fluoride-hexafluoropropylene (PVdF-HFP) gel polymer electrolyte and a polyethylene terephthalate (PET) non-woven support, to high-voltage and high-power lithium-ion batteries. In comparison to a commercialized polyethylene (PE) separator, the composite non-woven separator exhibits distinct improvements in microporous structure and liquid electrolyte wettability. Based on the understanding of the composite non-woven separator, cell performances of the separator at challenging charge/discharge conditions are investigated and discussed in terms of ion transport of the separator and AC impedance of the cell. The aforementioned advantageous features of the composite non-woven separator play a key role in providing facile ion transport and suppressing growth of cell impedance during cycling, which in turn contribute to superior cell performances at harsh charge/discharge conditions such as high voltages and high current densities.

Electrospun polyacrylonitrile/polyurethane composite nanofibrous separator with electrochemical performance for high power lithium ion batteries

Energy Technology Data Exchange (ETDEWEB)

Zainab, Ghazala [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Materials Science and Engineering, Donghua University, Shanghai 201620 (China); Wang, Xianfeng, E-mail: wxf@dhu.edu.cn [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Materials Science and Engineering, Donghua University, Shanghai 201620 (China); Key Laboratory of Textile Science & Technology, Ministry of Education, College of Textiles, Donghua University, Shanghai 201620 (China); Key Laboratory of High Performance Fibers & Products, Ministry of Education, College of Textiles, Donghua University, Shanghai 201620 (China); Nanofibers Research Center, Modern Textile Institute, Donghua University, Shanghai 200051 (China); Yu, Jianyong [Key Laboratory of Textile Science & Technology, Ministry of Education, College of Textiles, Donghua University, Shanghai 201620 (China); Key Laboratory of High Performance Fibers & Products, Ministry of Education, College of Textiles, Donghua University, Shanghai 201620 (China); Nanofibers Research Center, Modern Textile Institute, Donghua University, Shanghai 200051 (China); Zhai, Yunyun; Ahmed Babar, Aijaz; Xiao, Ke [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Materials Science and Engineering, Donghua University, Shanghai 201620 (China); Ding, Bin, E-mail: binding@dhu.edu.cn [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Materials Science and Engineering, Donghua University, Shanghai 201620 (China); Key Laboratory of Textile Science & Technology, Ministry of Education, College of Textiles, Donghua University, Shanghai 201620 (China); Key Laboratory of High Performance Fibers & Products, Ministry of Education, College of Textiles, Donghua University, Shanghai 201620 (China); Nanofibers Research Center, Modern Textile Institute, Donghua University, Shanghai 200051 (China)

2016-10-01

Lithium ion batteries (LIBs) for high performance require separators with auspicious reliability and safety. Keeping LIBs reliability and safety in view, microporous polyacrylonitrile (PAN)/polyurethane (PU) nonwoven composite separator have been developed by electrospinning technique. The physical, electrochemical and thermal properties of the PAN/PU separator were characterized. Improved ionic conductivity up to 2.07 S cm{sup −1}, high mechanical strength (10.38 MPa) and good anodic stability up to 5.10 V are key outcomes of resultant membranes. Additionally, high thermal stability displaying only 4% dimensional change after 0.5 h long exposure to 170 °C in an oven, which could be valuable addition towards the safety of LIBs. Comparing to commercialized polypropylene based separators, resulting membranes offered improved internal short-circuit protection function, offering better rate capability and enhanced capacity retention under same observation conditions. These fascinating characteristics endow these renewable composite nonwovens as promising separators for high power LIBs battery. - Highlights: • The PAN/PU based separators were prepared by multi-needle electrospinning technique. • The electrospun separators displays good mechanical properties and thermal stability. • These separators exhibit good wettability with liquid electrolyte, high ion conductivity and internal short-circuit protection. • Nanofibrous composite nonwoven possesses stable cyclic performance which give rise to acceptable battery performances.

Development of Novel Nano Polymer Composite Material for Solar Energy Conversion

International Nuclear Information System (INIS)

Sheha, E.; Elrasasi, T.Y.; El mansy, M.K.; Abdallah, B.

2014-01-01

PVA: Co 5 (OH) 8 (NO 3 ) 2 •2H 2 O polymer composite has been produced by casting of aqueous solution of mixed composite component. The nano polymer composites were characterized using structure techniques; XRD, SEM, FT-IR and TGA. The results indicated the formation composite without PVA degree of crystallinity variation. The measurements of electrical conductivity for the composites illustrated domination of ion conduction with activation energy (0.65-0.90) eV. The optical absorption illustrated an absorption peak around (530-540) nm which suggest electronic direct transition via energy gap width (1.90-2.16) eV. The electrochemical illustrated electrochemical band gap (1.97-3.26) eV

The localization of facial motor impairment in sporadic Möbius syndrome.

Science.gov (United States)

Cattaneo, L; Chierici, E; Bianchi, B; Sesenna, E; Pavesi, G

2006-06-27

To investigate the neurophysiologic aspects of facial motor control in patients with sporadic Möbius syndrome defined as nonprogressive congenital facial and abducens palsy. The authors assessed 24 patients with sporadic Möbius syndrome by performing a complete clinical examination and neurophysiologic tests including facial nerve conduction studies, needle electromyography examination of facial muscles, and recording of the blink reflex and of the trigeminofacial inhibitory reflex. Two distinct groups of patients were identified according to neurophysiologic testing. The first group was characterized by increased facial distal motor latencies (DMLs) and poor recruitment of small and polyphasic motor unit action potentials (MUAPs). The second group was characterized by normal facial DMLs and neuropathic MUAPs. It is hypothesized that in the first group, the disorder is due to a rhombencephalic maldevelopment with selective sparing of small-size MUs, and in the second group, the disorder is related to an acquired nervous injury during intrauterine life, with subsequent neurogenic remodeling of MUs. The trigeminofacial reflexes showed that in most subjects of both groups, the functional impairment of facial movements was caused by a nuclear or peripheral site of lesion, with little evidence of brainstem interneuronal involvement. Two different neurophysiologically defined phenotypes can be distinguished in sporadic Möbius syndrome, with different pathogenetic implications.

Compositional disordering of GaAs/AlGaAs multiple quantum wells using ion bombardment at elevated temperatures

International Nuclear Information System (INIS)

Anderson, K.K.; Donnelly, J.P.; Wang, C.A.; Woodhouse, J.D.; Haus, H.A.

1988-01-01

A new method has been developed for compositional mixing of heterostructures by ion bombardment at elevated temperatures. Complete mixing of a 1-μm-thick GaAs/AlGaAs 40-period multiple quantum well layer has been achieved by bombardment with 380 keV Ne + ions for 1 h with the sample at 700 0 C. This temperature is much lower than the annealing temperatures used in other vacancy-enhanced disordering techniques, and even lower temperatures and shorter durations should be possible. Compositional disordering is verified by sputter-profile Auger electron spectroscopy and transmission electron microscopy. Complete mixing is also demonstrated by optical transmission spectra of the disordered material, which exhibit the same band edge as a uniform alloy with the average aluminum mole fraction of the multiple quantum well layer

Mapping of gene expression reveals CYP27A1 as a susceptibility gene for sporadic ALS.

Directory of Open Access Journals (Sweden)

Frank P Diekstra

Full Text Available Amyotrophic lateral sclerosis (ALS is a progressive, neurodegenerative disease characterized by loss of upper and lower motor neurons. ALS is considered to be a complex trait and genome-wide association studies (GWAS have implicated a few susceptibility loci. However, many more causal loci remain to be discovered. Since it has been shown that genetic variants associated with complex traits are more likely to be eQTLs than frequency-matched variants from GWAS platforms, we conducted a two-stage genome-wide screening for eQTLs associated with ALS. In addition, we applied an eQTL analysis to finemap association loci. Expression profiles using peripheral blood of 323 sporadic ALS patients and 413 controls were mapped to genome-wide genotyping data. Subsequently, data from a two-stage GWAS (3,568 patients and 10,163 controls were used to prioritize eQTLs identified in the first stage (162 ALS, 207 controls. These prioritized eQTLs were carried forward to the second sample with both gene-expression and genotyping data (161 ALS, 206 controls. Replicated eQTL SNPs were then tested for association in the second-stage GWAS data to find SNPs associated with disease, that survived correction for multiple testing. We thus identified twelve cis eQTLs with nominally significant associations in the second-stage GWAS data. Eight SNP-transcript pairs of highest significance (lowest p = 1.27 × 10(-51 withstood multiple-testing correction in the second stage and modulated CYP27A1 gene expression. Additionally, we show that C9orf72 appears to be the only gene in the 9p21.2 locus that is regulated in cis, showing the potential of this approach in identifying causative genes in association loci in ALS. This study has identified candidate genes for sporadic ALS, most notably CYP27A1. Mutations in CYP27A1 are causal to cerebrotendinous xanthomatosis which can present as a clinical mimic of ALS with progressive upper motor neuron loss, making it a plausible

Reactive GTS Allocation Protocol for Sporadic Events Using the IEEE 802.15.4

Directory of Open Access Journals (Sweden)

Mukhtar Azeem

2014-01-01

by the IEEE 802.15.4 standard. The proposed control protocol ensures that a given offline sporadic schedule can be adapted online in a timely manner such that the static periodic schedule has not been disturbed and the IEEE 802.15.4 standard compliance remains intact. The proposed protocol is simulated in OPNET. The simulation results are analyzed and presented in this paper to prove the correctness of the proposed protocol regarding the efficient real-time sporadic event delivery along with the periodic event propagation.

Are clusters important in understanding the mechanisms in atmospheric pressure ionization? Part 1: Reagent ion generation and chemical control of ion populations.

Science.gov (United States)

Klee, Sonja; Derpmann, Valerie; Wißdorf, Walter; Klopotowski, Sebastian; Kersten, Hendrik; Brockmann, Klaus J; Benter, Thorsten; Albrecht, Sascha; Bruins, Andries P; Dousty, Faezeh; Kauppila, Tiina J; Kostiainen, Risto; O'Brien, Rob; Robb, Damon B; Syage, Jack A

2014-08-01

It is well documented since the early days of the development of atmospheric pressure ionization methods, which operate in the gas phase, that cluster ions are ubiquitous. This holds true for atmospheric pressure chemical ionization, as well as for more recent techniques, such as atmospheric pressure photoionization, direct analysis in real time, and many more. In fact, it is well established that cluster ions are the primary carriers of the net charge generated. Nevertheless, cluster ion chemistry has only been sporadically included in the numerous proposed ionization mechanisms leading to charged target analytes, which are often protonated molecules. This paper series, consisting of two parts, attempts to highlight the role of cluster ion chemistry with regard to the generation of analyte ions. In addition, the impact of the changing reaction matrix and the non-thermal collisions of ions en route from the atmospheric pressure ion source to the high vacuum analyzer region are discussed. This work addresses such issues as extent of protonation versus deuteration, the extent of analyte fragmentation, as well as highly variable ionization efficiencies, among others. In Part 1, the nature of the reagent ion generation is examined, as well as the extent of thermodynamic versus kinetic control of the resulting ion population entering the analyzer region.

Ferrous Ion and Medium Composition Effects on Acidogenic Phase in Biobutanol Production from Molasses

Science.gov (United States)

Restiawaty, E.; Grinanda, D.

2017-07-01

Clostridium acetobutylicum B530 has ability to convert sugar into biobutanol through two phases, i.e. acidogenic and solventogenic. This fermentation process is often hampered by high raw material cost and low product yield. In order to suppress the production cost, the molasses, a byproduct of sugar cane process production, was used as carbon source in this research. Molasses has nitrogen content in a small amount, thus could be negating the beef extract component, which is expected not to affect the growth of C. acetobutylicum B530 and also can reduce the production cost. In addition, a certain amount of Fe2+ (ferrous ion), a precursor in the formation of the enzyme ferredoxin, was added to the fermentation medium to contribute in the synthesis of acetyl-CoA, so that the formation of acidogenic products such as butyric acid and acetic acid is affected. This study aimed to investigate the effect of ferrous ion and the medium composition in acidogenic phase. The addition of 20 ppm FeSO4.7H2O in the fermentation medium without beef extract can increase the concentration of butyric acid by 20% at a temperature of 35°C, while acetic acid concentration decreased by 6%. According to those results, it is expected that the product selectivity of butanol will increase in solventogenic phase. In addition, the removal of beef extract in the fermentation medium does not affect the kinetics of growth of C. acetobutylicum B530.

Development of plasma-treated polypropylene nonwoven-based composites for high-performance lithium-ion battery separators

International Nuclear Information System (INIS)

Li, Xiaofei; He, Jinlin; Wu, Dazhao; Zhang, Mingzu; Meng, Juwen; Ni, Peihong

2015-01-01

Graphical abstract: A composite separator based on plasma-treated fluorinated polypropylene (PP) nonwoven, poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP) and SiO 2 nanoparticles exhibiting enhanced thermal stability, ionic conductivity and electrochemical properties. Display Omitted -- Highlights: •Fluorinated segments are introduced on the surface of PP nonwoven through plasma treatment. •The obtained composite separators exhibit better physical and electrochemical properties. •The capacity of half-cell with composite separator keeps above 150 mA h g −1 after 100 charge–discharge cycles. -- Abstract: Separators have drawn substantial attention because of their important role in achieving the safety and good electrochemical performance of lithium-ion batteries. In this study, we report a new type of composite membrane prepared by a combination of fluorinated polypropylene (PP) nonwoven fabric, poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP) and SiO 2 nanoparticles. 2, 2, 3, 3, 4, 4, 5, 5-Octafluoropentyl methacrylate (OFPMA) is first grafted on the surface of PP nonwoven by plasma treatment to improve the nonwoven’s adhesion with PVdF-HFP. Two kinds of composite separators have been prepared by using the different PP nonwovens together with PVdF-HFP and SiO 2 nanoparticles. They were separately designated as PHS for commercially raw PP nonwoven system and PHS-n for OFPMA-modified PP nonwoven systems (n means plasma treatment time). The morphology, electrolyte uptake, ionic conductivity and electrochemical properties of the composite separators have been analyzed by scanning electron microscope (SEM) analysis, impedance measurement, charge-discharge cycle and C-rate tests, respectively. The results indicate that PHS-10 composite separator using the modified PP nonwoven treated by plasma for 10 min exhibits much better properties than PHS separator, including an improved mechanical property, thermal stability, electrolyte uptake

Association between rs6812193 polymorphism and sporadic Parkinson's disease susceptibility.

Science.gov (United States)

Huo, Qiang; Li, Tao; Zhao, Peiqing; Wang, Lianqing

2015-08-01

Recently, the association of a single nucleotide polymorphism rs6812193 C/T with sporadic Parkinson's disease (PD) susceptibility has been widely evaluated, but the results remained inconsistent. This association should be clarified because of the importance of it on human health and quality of life. We performed a comprehensive meta-analysis to evaluate the association between the rs6812193 polymorphism and sporadic PD. PubMed was used to retrieve articles published up to June 2014 for all studies evaluating the rs6812193 polymorphism and PD in humans. Ethnicity-specific subgroup analysis was also performed based on ethnicity susceptibility. A total of 17 independent study samples (15 Caucasians and 2 Asians) including 17,956 cases and 52,751 controls were used in the presented study. The MAFT (minor allele T frequency) in PD patients of European descent is obviously higher than Asian cases (p susceptibility among overall samples (OR 0.882, 95 % CI 0.856-0.908) and Caucasian population (OR 0.881, 95 % CI 0.856-0.907), but not in Asian samples (OR 0.918, 95 % CI 0.721-1.168). No evidence of publication bias was observed. Throughout our analysis, the rs6812193 polymorphism is significantly associated with sporadic PD susceptibility in Caucasian samples, and ethnicity might be the key point of inconsistency in rs6812193 studies. Further studies are warranted to re-examine the observed associations, especially in different ethnicities.

Material composition – Pinning strength correlation in Nb thin films with focused ion beam-milled washboard nanostructures

International Nuclear Information System (INIS)

Dobrovolskiy, Oleksandr V.; Begun, Evgeniya; Huth, Michael; Shklovskij, Valerij A.

2013-01-01

Highlights: •We fabricated an array of grooves in Nb films by using focused ion beam milling. •We determined the material composition in different areas of the processed films. •We deduced the pinning activation energies from the magneto-resistivity data. •We obtained the material composition – pinning strength correlation in the processed films. -- Abstract: An analysis of the interrelated changes in the material composition and the pinning strength in nanostructured Nb (1 1 0) thin films is presented. The nanopatterns were prepared by focused ion beam milling of an array of uniaxial grooves. They induce a washboard-like pinning potential landscape for vortices in the mixed state. By applying different magnetic fields, the most likely pinning sites along which the flux lines move through the samples have been selected. By this, either the background isotropic pinning of the pristine film or the enhanced isotropic pinning originating from the nanoprocessing has been probed. The enhanced pinning strength in the processed films has been found to correlate with the content of Ga implanted into the films during the nanopatterning

Material composition – Pinning strength correlation in Nb thin films with focused ion beam-milled washboard nanostructures

Energy Technology Data Exchange (ETDEWEB)

Dobrovolskiy, Oleksandr V., E-mail: Dobrovolskiy@Physik.uni-frankfurt.de [Physikalisches Institut, Goethe-Universität, 60438 Frankfurt am Main (Germany); Physical Department, Kharkiv National University, 61077 Kharkiv (Ukraine); Begun, Evgeniya; Huth, Michael [Physikalisches Institut, Goethe-Universität, 60438 Frankfurt am Main (Germany); Shklovskij, Valerij A. [Physical Department, Kharkiv National University, 61077 Kharkiv (Ukraine); Institute for Theoretical Physics, NSC-KIPT, 61108 Kharkiv (Ukraine)

2013-11-15

Highlights: •We fabricated an array of grooves in Nb films by using focused ion beam milling. •We determined the material composition in different areas of the processed films. •We deduced the pinning activation energies from the magneto-resistivity data. •We obtained the material composition – pinning strength correlation in the processed films. -- Abstract: An analysis of the interrelated changes in the material composition and the pinning strength in nanostructured Nb (1 1 0) thin films is presented. The nanopatterns were prepared by focused ion beam milling of an array of uniaxial grooves. They induce a washboard-like pinning potential landscape for vortices in the mixed state. By applying different magnetic fields, the most likely pinning sites along which the flux lines move through the samples have been selected. By this, either the background isotropic pinning of the pristine film or the enhanced isotropic pinning originating from the nanoprocessing has been probed. The enhanced pinning strength in the processed films has been found to correlate with the content of Ga implanted into the films during the nanopatterning.

Composition variations of low energy heavy ions during large solar energetic particle events

Energy Technology Data Exchange (ETDEWEB)

Ho, George C., E-mail: George.Ho@jhuapl.edu; Mason, Glenn M., E-mail: Glenn.Mason@jhuapl.edu [Johns Hopkins University Applied Physics Laboratory, Laurel, MD 20723 (United States)

2016-03-25

The time-intensity profile of large solar energetic particle (SEP) event is well organized by solar longitude as observed at Earth orbit. This is mostly due to different magnetic connection to the shock that is associated with large SEP event propagates from the Sun to the heliosphere. Earlier studies have shown event averaged heavy ion abundance ratios can also vary as a function of solar longitude. It was found that the Fe/O ratio for high energy particle (>10 MeV/nucleon) is higher for those western magnetically well connected events compare to the eastern events as observed at L1 by the Advanced Composition Explorer (ACE) spacecraft. In this paper, we examined the low energy (∼1 MeV/nucleon) heavy ions in 110 isolated SEP events from 2009 to the end of 2014. In addition, the optical and radio signatures for all of our events are identified and when data are available we also located the associated coronal mass ejection (CME) data. Our survey shows a higher Fe/O ratio at events in the well-connected region, while there are no corrections between the event averaged elemental composition with the associated coronal mass ejection speed. This is inconsistent with the higher energy results, but inline with other recent low-energy measurements.

Fe3O4/C composite with hollow spheres in porous 3D-nanostructure as anode material for the lithium-ion batteries

Science.gov (United States)

Yang, Zhao; Su, Danyang; Yang, Jinping; Wang, Jing

2017-09-01

3d transition-metal oxides, especially Fe3O4, as anode materials for the lithium-ion batteries have been attracting intensive attentions in recent years due to their high energy capacity and low toxicity. A new Fe3O4/C composite with hollow spheres in porous three-dimensional (3D) nanostructure, which was synthesized by a facile solvothermal method using FeCl3·6H2O and porous spongy carbon as raw materials. The specific surface area and microstructures of composite were characterized by nitrogen adsorption-desorption isotherm method, FE-SEM and HR-TEM. A homogeneous distribution of hollow Fe3O4 spheres (diameter ranges from 120 nm to 150 nm) in the spongy carbon (pore size > 200 nm) conductive 3D-network significantly reduced the lithium-ion diffusion length and increased the electrochemical reaction area, and further more enhanced the lithium ion battery performance, such as discharge capacity and cycle life. As an anode material for the lithium-ion battery, the title composite exhibit excellent electrochemical properties. The Fe3O4/C composite electrode achieved a relatively high reversible specific capacity of 1450.1 mA h g-1 in the first cycle at 100 mA g-1, and excellent rate capability (69% retention at 1000 mA g-1) with good cycle stability (only 10% loss after 100 cycles).

Higher cytoplasmic and nuclear poly(ADP-ribose) polymerase expression in familial than in sporadic breast cancer

NARCIS (Netherlands)

Klauke, M.L.; Hoogerbrugge-van der Linden, N.; Budczies, J.; Bult, P.; Prinzler, J.; Radke, C.; van Krieken, J.H.; Dietel, M.; Denkert, C.; Muller, B.M.

2012-01-01

Poly(ADP-ribose) polymerase 1 (PARP) is a key element of the single-base excision pathway for repair of DNA single-strand breaks. To compare the cytoplasmic and nuclear poly(ADP-ribose) expression between familial (BRCA1, BRCA2, or non BRCA1/2) and sporadic breast cancer, we investigated 39 sporadic

Multiple imputation by chained equations for systematically and sporadically missing multilevel data.

Science.gov (United States)

Resche-Rigon, Matthieu; White, Ian R

2018-06-01

In multilevel settings such as individual participant data meta-analysis, a variable is 'systematically missing' if it is wholly missing in some clusters and 'sporadically missing' if it is partly missing in some clusters. Previously proposed methods to impute incomplete multilevel data handle either systematically or sporadically missing data, but frequently both patterns are observed. We describe a new multiple imputation by chained equations (MICE) algorithm for multilevel data with arbitrary patterns of systematically and sporadically missing variables. The algorithm is described for multilevel normal data but can easily be extended for other variable types. We first propose two methods for imputing a single incomplete variable: an extension of an existing method and a new two-stage method which conveniently allows for heteroscedastic data. We then discuss the difficulties of imputing missing values in several variables in multilevel data using MICE, and show that even the simplest joint multilevel model implies conditional models which involve cluster means and heteroscedasticity. However, a simulation study finds that the proposed methods can be successfully combined in a multilevel MICE procedure, even when cluster means are not included in the imputation models.

Ion transport studies on Pb(NO3)2:Al2O3 composite solid electrolytes: Effect of dispersoid particle size

Science.gov (United States)

Reddy, Y. Govinda; Sekhar, M. Chandra; Sadananda Chary, A.; Narender Reddy, S.

2018-02-01

Composites of Alumina dispersed Lead Nitrate of different particles sizes (0.3µm, 36.9µm) were prepared through mechanical mixing process. These composites have been characterized by using XRD and SEM. Transport properties of these systems have been studied by means of impedance spectroscopy in the frequency range 100Hz to 4MHz in the temperature range from room temperature to 300°C. Temperature dependent conductivity spectra for composites with different mole percentages of alumina and with different particle sizes (0.3µm, 36.9µm) studied. The contact surface area between host and dispersoid increases with the decrease in particle size. These studies indicate that the conductivity in these systems is mainly due to the contribution enhanced concentration of mobile ions at the interfacial regions of host and dispersoid materials and increased mobility of charge carriers along the grain boundaries. It is believed that mechanism of conductivity through anti-Frenkel disorder (NO3 - ions) in these composites.

High prevalence of exon 8 G533C mutation in apparently sporadic medullary thyroid carcinoma in Greece.

Science.gov (United States)

Sarika, H L; Papathoma, A; Garofalaki, M; Vasileiou, V; Vlassopoulou, B; Anastasiou, E; Alevizaki, M

2012-12-01

Genetic screening for ret mutation has become routine practice in the evaluation of medullary thyroid carcinoma (MTC). Approximately 25% of these tumours are familial, and they occur as components of the multiple endocrine neoplasia type 2 syndromes (MEN 2A and 2B) or familial MTC. In familial cases, the majority of mutations are found in exons 10, 11, 13, 14 or 15 of the ret gene. A rare mutation involving exon 8 (G533C) has recently been reported in familial cases of MTC in Brazil and Greece; some of these cases were originally thought to be sporadic. The aim of this study was to re-evaluate a series of sporadic cases of MTC, with negative family history, and screen them for germline mutations in exon 8. Genomic DNA was extracted from peripheral lymphocytes in 129 unrelated individuals who had previously been characterized as 'sporadic' based on the negative family history and negative screening for ret gene mutations. Samples were analysed in Applied Biosystems 7500 real-time PCR and confirmed by sequencing. The G533C exon 8 mutation was identified in 10 of 129 patients with sporadic MTC. Asymptomatic gene carriers were subsequently identified in other family members. In our study, we found that 7·75% patients with apparently sporadic MTC do carry G533C mutation involving exon 8 of ret. We feel that there is now a need to include exon 8 mutation screening in all patients diagnosed as sporadic MTC, in Greece. © 2012 Blackwell Publishing Ltd.

[The practice guideline 'Dermatomyositis, polymyositis and sporadic inclusion body myositis'

NARCIS (Netherlands)

Hoogendijk, J.E.; Bijlsma, J.W.J.; Engelen, B.G.M. van; Lindeman, E.J.M.; Royen-Kerkhof, A. van; Rie, M.A. de; Visser, M. de; Jennekens, F.G.I.

2005-01-01

This guideline presents recommendations for the diagnosis and treatment of dermatomyositis, polymyositis and sporadic inclusion body myositis (sIBM) according to the best available evidence. Characteristic skin abnormalities can be sufficient for the diagnosis of dermatomyositis. In case of doubt, a

N-doped graphene/graphite composite as a conductive agent-free anode material for lithium ion batteries with greatly enhanced electrochemical performance

International Nuclear Information System (INIS)

Guanghui, Wu; Ruiyi, Li; Zaijun, Li; Junkang, Liu; Zhiguo, Gu; Guangli, Wang

2015-01-01

Graphical abstract: The study reported a novel N-doped graphene/graphite anode material for lithium ion batteries. The composite exhibits a largely enhanced electrochemical performance. The study also provides an attractive approach for the fabrication of various graphite-based materials for high power batteries. Display Omitted -- Highlights: • The paper developed a new N-doped graphene/graphite composite for lithium ion battery • The composite contains a three-dimensional graphene framework with rich of open pores • The hybrid offers a higher electrical conductivity when compared with pristine graphite • The hybrid electrode provides a greatly enhanced electrochemical performance • The study provides a prominent approach for fabrication of graphite-based materials -- ABSTRACT: Present graphite anode cannot meet the increasing requirement of electronic devices and electric vehicles due to its low specific capacity, poor cycle stability and low rate capability. The study reported a promising N-doped graphene/graphite composite as a conductive agent-free anode material for lithium ion batteries. Herein, graphite oxide and urea were dispersed in ultrapure water and partly reduced by ascorbic acid. Followed by mixing with graphite and hydrothermal treatment to produce graphene oxide/graphite hydrogel. The hydrogel was dried and finally annealed in Ar/H 2 to obtain N-doped graphene/graphite composite. The result shows that all of graphite particles was dispersed in three-dimensional graphene framework with a rich of open pores. The open pore accelerates the electrolyte transport. The graphene framework works as a conductive agent and graphite particle connector and improves the electron transfer. Electrical conductivity of the composite reaches 5912 S m −1 , which is much better than that of the pristine graphite (4018 S m −1 ). The graphene framework also acts as an expansion absorber in the anodes of lithium ion battery to relieve the large strains

Interaction of a neutral composite particle with a strong Coulomb field

International Nuclear Information System (INIS)

Wong, Cheuk-Yin.

1988-01-01

The author discusses the interaction of the quasi-composite (e/sup /plus//e/sup /minus//) system with an external electromagnetic field. This problem addresses the question of the origin of strong positron lines in quasi-elastic heavy-ion reactions. 3 refs

Effect of rare earth substitution on properties of barium strontium titanate ceramic and its multiferroic composite with nickel cobalt ferrite

International Nuclear Information System (INIS)

Pahuja, Poonam; Kotnala, R.K.; Tandon, R.P.

2014-01-01

Highlights: • Rare earth ions Dy 3+ , Gd 3+ and Sm 3+ have been substituted in Ba 0.95 Sr 0.05 TiO 3 (BST). • Ni 0.8 Co 0.2 Fe 2 O 4 has been used as ferrimagnetic phase to obtain composites. • Substitution of these ions increases dielectric constant of BST and composites. • Magnetoelectric coefficient of composites increases on substitution of these ions. - Abstract: Effect of substitution of rare earth ions (Dy 3+ , Gd 3+ and Sm 3+ ) on various properties of Ba 0.95 Sr 0.05 TiO 3 (BST) i.e. the composition Ba 0.95−1.5x Sr 0.05 R x TiO 3 (where x = 0.00, 0.01, 0.02, 0.03 and R are rare earths Dy, Gd, Sm) and that of their multiferroic composite with Ni 0.8 Co 0.2 Fe 2 O 4 (NCF) has been studied. Shifting of peaks corresponding to different compositions in the X-ray diffraction pattern confirmed the substitution of rare earth ions at both Ba 2+ and Ti 4+ sites in BST. It is clear from scanning electron microscopy (SEM) images that rare earth substitution in BST increases its grain size in both pure and composite samples. Substitution of rare earth ions results in increase in value of dielectric constant of pure and composite samples. Sm substitution in BST significantly decreases its Curie temperature. Dy substituted pure and composite samples possess superior ferroelectric properties as confirmed by polarization vs electric field (P–E) loops. Composite samples containing Dy, Gd and Sm substituted BST as ferroelectric phase possess lower values of remanent and saturation magnetizations in comparison to composite sample containing pure BST as ferroelectric phase (BSTC). Rare earth substituted composite samples possess higher value of magnetoelectric coefficient as compared to that for BSTC

Characterization of silicon- and carbon-based composite anodes for lithium-ion batteries

International Nuclear Information System (INIS)

Khomenko, Volodymyr G.; Barsukov, Viacheslav Z.

2007-01-01

In recent years development of active materials for negative electrodes has been of great interest. Special attention has been focused on the active materials possessing higher reversible capacity than that of conventional graphite. In the present work the electrochemical performance of some carbon/silicon-based materials has been analyzed. For this purpose various silicon-based composites were prepared using such carbon materials as graphite, hard carbon and graphitized carbon black. An analysis of charging-discharging processes at electrodes based on different carbon materials has shown that graphite modified with silicon is the most promising anode material. It has also been revealed that the irreversible capacity mainly depends on the content of Si. An optimum content of Si has been determined with taking into account that high irreversible capacity is not suitable for practical application in lithium-ion batteries. This content falls within the range of 8-10 wt%. The reversible capacity of graphite modified with 8 wt% carbon-coated Si was as high as 604 mAh g -1 . The irreversible capacity loss with this material was as low as 8.1%. The small irreversible capacity of the material allowed developing full lithium-ion rechargeable cells in the 2016 coin cell configuration. Lithium-ion batteries based on graphite modified with silicon show gravimetric and volumetric specific energy densities which are higher by approximately 20% than those for a lithium-ion battery based on natural graphite

In situ Raman spectroscopic studies on concentration change of electrolyte salt in a lithium ion model battery with closely faced graphite composite and LiCoO2 composite electrodes by using an ultrafine microprobe

International Nuclear Information System (INIS)

Yamanaka, Toshiro; Nakagawa, Hiroe; Tsubouchi, Shigetaka; Domi, Yasuhiro; Doi, Takayuki; Abe, Takeshi; Ogumi, Zempachi

2017-01-01

The concentration of ions in the electrolyte solution in lithium ion batteries changes during operation, reflecting the resistance to ion migration and the positions of diffusion barriers. The change causes various negative effects on the performance of batteries. Thus, it is important to elucidate how the concentration changes during operation. In this work, the concentration change of ions in the electrolyte solution in deep narrow spaces in a realistic battery was studied by in situ ultrafine microprobe Raman spectroscopy. Graphite composite and LiCoO 2 composite electrodes, which are the most commonly used electrodes in practical batteries, were placed facing each other and their distance was set to 80 μm, which is close to the distance between electrodes in practical batteries. After repeated charge/discharge cycles, the concentration of ions increased and decreased greatly during charging and discharging, respectively. The maximum concentration was more than three-times higher than the minimum concentration. The rate of changes in concentration increased almost linearly with increase in current density. The results have important implications about concentration changes of ions occurring in practical batteries.

Structural and composition investigations at delayered locations of low k integrated circuit device by gas-assisted focused ion beam

Energy Technology Data Exchange (ETDEWEB)

Wang, Dandan, E-mail: dandan.wang@globalfoundries.com; Kee Tan, Pik; Yamin Huang, Maggie; Lam, Jeffrey; Mai, Zhihong [Technology Development Department, GLOBALFOUNDRIES Singapore Pte. Ltd., 60 Woodlands Industrial Park D, Street 2, Singapore 738406 (Singapore)

2014-05-15

The authors report a new delayering technique – gas-assisted focused ion beam (FIB) method and its effects on the top layer materials of integrated circuit (IC) device. It demonstrates a highly efficient failure analysis with investigations on the precise location. After removing the dielectric layers under the bombardment of an ion beam, the chemical composition of the top layer was altered with the reduced oxygen content. Further energy-dispersive x-ray spectroscopy and Fourier transform infrared analysis revealed that the oxygen reduction lead to appreciable silicon suboxide formation. Our findings with structural and composition alteration of dielectric layer after FIB delayering open up a new insight avenue for the failure analysis in IC devices.

Examination of the Thermo-mechanical Properties of E-Glass/Carbon Composites

Directory of Open Access Journals (Sweden)

Hande Sezgin

2017-12-01

Full Text Available Eight-ply E-glass, carbon and E-glass/carbon fabric-reinforced polyester based hybrid composites were manufactured in this study. A vacuum infusion system was used as the production method. Dynamic mechanical analysis, thermogravimetric analysis and differential scanning calorimetry analysis were conducted to examine the thermo-mechanical properties of composite samples. The effect of reinforcement type and different stacking sequences of fabric plies on the thermo-mechanical properties of composite samples were also investigated. Results showed that the type and alignment of reinforcement material has a signifi cant effect on the dynamic mechanical properties of composite samples.

Treatment of low level radioactive liquid wastes using composite ion-exchange resins based on polyurethane foam

International Nuclear Information System (INIS)

Rao, S.V.S.; Lekshmi, R.; Mani, A.G.S.; Sinha, P.K.

2010-01-01

Composite ion-exchange resins were prepared by coating copper-ferrocyanide (CFC) and hydrous manganese oxide (HMO) powders on polyurethane (PU) foam. Polyvinyl acetate/Acetone was used as a binder. The foam was loaded with about five times its weight with CFC and HMO powders. The distribution coefficients of CFC-PU foam and HMO-PU foam for cesium and strontium respectively were estimated. Under similar conditions the HMO-PU foam showed higher capacity as well as better kinetics for removal of strontium than CFC-PU foam for Cs. The pilot plant scale studies were conducted using a mixed composite ion-exchange resin bed. About 1000 bed volumes could be passed before attaining a DF of 10 from an initial value of 60-80. The spent resin was digested in alkaline KMnO 4 and the digested liquid was fixed in cement matrix. The matrices were characterized with respect to compressive strength and leach resistance. (author)

When does ALS start? ADAR2-GluA2 hypothesis for the etiology of sporadic ALS

Directory of Open Access Journals (Sweden)

Takuto eHideyama

2011-11-01

Full Text Available Amyotrophic lateral sclerosis (ALS is the most common adult-onset motor neuron disease. More than 90% of ALS cases are sporadic, and the majority of sporadic ALS patients do not carry mutations in genes causative of familial ALS; therefore, investigation specifically targeting sporadic ALS is needed to discover the pathogenesis. The motor neurons of sporadic ALS patients express unedited GluA2 mRNA at the Q/R site in a disease-specific and motor neuron-selective manner. GluA2 is a subunit of the AMPA receptor, and it has a regulatory role in the Ca2+-permeability of the AMPA receptor after the genomic Q codon is replaced with the R codon in mRNA by adenosine-inosine conversion, which is mediated by adenosine deaminase acting on RNA 2 (ADAR2. Therefore, ADAR2 activity may not be sufficient to edit all GluA2 mRNA expressed in the motor neurons of ALS patients. To investigate whether deficient ADAR2 activity plays pathogenic roles in sporadic ALS, we generated genetically modified mice (AR2 in which the ADAR2 gene was conditionally knocked out in the motor neurons. AR2 mice showed an ALS-like phenotype with the death of ADAR2-lacking motor neurons. Notably, the motor neurons deficient in ADAR2 survived when they expressed only edited GluA2 in AR2/GluR-BR/R (AR2res mice, in which the endogenous GluA2 alleles were replaced by the GluR-BR allele that encoded edited GluA2. In heterozygous AR2 mice with only one ADAR2 allele, approximately 20% of the spinal motor neurons expressed unedited GluA2 and underwent degeneration, indicating that half-normal ADAR2 activity is not sufficient to edit all GluA2 expressed in motor neurons. It is likely therefore that the expression of unedited GluA2 causes the death of motor neurons in sporadic ALS. We hypothesize that a progressive downregulation of ADAR2 activity plays a critical role in the pathogenesis of sporadic ALS and that the pathological process commences when motor neurons express unedited GluA2.

Localized Beampipe Heating due to $e^{-}$ Capture and Nuclear Excitation in Heavy Ion Colliders

CERN Document Server

Klein, S R

2001-01-01

At heavy ion colliders, two major sources of beam loss are expected to be $e^+e^-$ production, where the $e^-$ is bound to one of the nuclei, and photonuclear excitation and decay via neutron emission. Both processes alter the ions charged to mass ratio by well defined amounts, creating beams of particles with altered magnetic rigidity. These beams will deposit their energy in a localized region of the accelerator, causing localized heating, The size of the target region depends on the collider optics. For medium and heavy ions, at design luminosity at the Large Hadron Collider, local heating may be more than an order of magnitude higher than expected. This could cause magnet quenches if the local cooling is inadequate. The altered-rigidity beams will also produce localized radiation damage. The beams could also be extracted and used for fixed target experiments.

Effect of sulfate ions on the crystallization and photocatalytic activity of TiO2/diatomite composite photocatalyst

Science.gov (United States)

Zhang, Jinjun; Wang, Xiaoyan; Wang, Jimei; Wang, Jing; Ji, Zhijiang

2016-01-01

TiO2 nanoparticles were immobilized on diatomite by hydrolysis-deposition method using titanium tetrachloride as precursor. The effect of sulfate ions on the crystallization and photocatalytic activity of TiO2/diatomite composite photocatalyst was characterized by TG-DSC, XRD, BET surface area, SEM, FT-IR spectroscopy, XPS and UV-vis diffuse reflectance spectra. The results indicate that addition of a small amount of sulfate ions promotes the formation of anatase phase and inhibits the transformation from anatase to rutile. On the other hand, sulfate ions immobilized on the surface of TiO2/diatomite have strong affinity for electrons, capturing the photo-generated electrons, which hinders the recombination of electrons and holes.

Synthesis and electrochemical characteristics of Sn-Sb-Ni alloy composite anode for Li-ion rechargeable batteries

International Nuclear Information System (INIS)

Guo Hong; Zhao Hailei; Jia Xidi; Qiu Weihua; Cui Fenge

2007-01-01

Micro-scaled Sn-Sb-Ni alloy composite was synthesized from oxides of Sn, Sb and Ni via carbothermal reduction. The phase composition and electrochemical properties of the Sn-Sb-Ni alloy composite anode material were studied. The prepared alloy composite electrode exhibits a high specific capacity and a good cycling stability. The lithiation capacity was 530 mAh g -1 in the first cycle and maintained at 370-380 mAh g -1 in the following cycles. The good electrochemical performance may be attributed to its relatively large particle size and multi-phase characteristics. The former reason leads to the lower surface impurity and thus the lower initial capacity loss, while the latter results in a stepwise lithiation/delithiation behavior and a smooth volume change of electrode in cycles. The Sn-Sb-Ni alloy composite material shows a good candidate anode material for the rechargeable lithium ion batteries

Slower Dynamics and Aged Mitochondria in Sporadic Alzheimer's Disease

Science.gov (United States)

Gargini, Ricardo; García, Esther; Perry, George

2017-01-01

Sporadic Alzheimer's disease corresponds to 95% of cases whose origin is multifactorial and elusive. Mitochondrial dysfunction is a major feature of Alzheimer's pathology, which might be one of the early events that trigger downstream principal events. Here, we show that multiple genes that control mitochondrial homeostasis, including fission and fusion, are downregulated in Alzheimer's patients. Additionally, we demonstrate that some of these dysregulations, such as diminished DLP1 levels and its mitochondrial localization, as well as reduced STOML2 and MFN2 fusion protein levels, take place in fibroblasts from sporadic Alzheimer's disease patients. The analysis of mitochondrial network disruption using CCCP indicates that the patients' fibroblasts exhibit slower dynamics and mitochondrial membrane potential recovery. These defects lead to strong accumulation of aged mitochondria in Alzheimer's fibroblasts. Accordingly, the analysis of autophagy and mitophagy involved genes in the patients demonstrates a downregulation indicating that the recycling mechanism of these aged mitochondria might be impaired. Our data reinforce the idea that mitochondrial dysfunction is one of the key early events of the disease intimately related with aging. PMID:29201274

Plasma immersion ion implantation for the efficient surface modification of medical materials

International Nuclear Information System (INIS)

Slabodchikov, Vladimir A.; Borisov, Dmitry P.; Kuznetsov, Vladimir M.

2015-01-01

The paper reports on a new method of plasma immersion ion implantation for the surface modification of medical materials using the example of nickel-titanium (NiTi) alloys much used for manufacturing medical implants. The chemical composition and surface properties of NiTi alloys doped with silicon by conventional ion implantation and by the proposed plasma immersion method are compared. It is shown that the new plasma immersion method is more efficient than conventional ion beam treatment and provides Si implantation into NiTi surface layers through a depth of a hundred nanometers at low bias voltages (400 V) and temperatures (≤150°C) of the substrate. The research results suggest that the chemical composition and surface properties of materials required for medicine, e.g., NiTi alloys, can be successfully attained through modification by the proposed method of plasma immersion ion implantation and by other methods based on the proposed vacuum equipment without using any conventional ion beam treatment

Hierarchical carambola-like Li4Ti5O12-TiO2 composites as advanced anode materials for lithium-ion batteries

International Nuclear Information System (INIS)

Zhang, Yu; Zhang, Yun; Huang, Ling; Zhou, Zhongfu; Wang, Jingfeng; Liu, Heng; Wu, Hao

2016-01-01

Hierarchically structured Li 4 Ti 5 O 12 -TiO 2 (LTO-TiO 2 ) composites are synthesized using a facile hydrothermal approach upon reaction time control. With control over the time of hydrothermal reaction at 18 h, a hierarchical dual-phase LTO-TiO 2 composite with appropriate amount of anatase TiO 2 can be obtained, and it possesses a uniform carambola-like framework assembled by numerous ultrathin nanosheets, which enable a relatively large specific surface area, along with abundant interlayer channels to favor electrolyte penetration. When used as anode materials for lithium-ion batteries, such carambola-like LTO-TiO 2 composite exhibits remarkably improved capacity, high-rate capability, and cycling stability over other LTO-TiO 2 samples, which are synthesized at different time of hydrothermal reaction. Specifically, it deliveries a discharge capacity as high as 115.1 and 91.2 mAh g −1 at a very high current rate of 20 and 40C, respectively, while a stable reversible capacity of 171.7 mAh g −1 can be retained after 200 charge-discharge cycles at 1C, corresponding to 88.6% capacity retention. The excellent electrochemical performances benefit from the unique hierarchical carambola-like structure together with the mutually complementary intrinsic advantages between LTO and TiO 2 . The robust and porous nanosheets-assembled LTO-TiO 2 framework not only offers a shorter transport pathway for electron and Li-ion migration within this composite material, but also is able to alleviate the structure distortion during the fast Li-ion insertion/extraction process. The work described here shows that the hierarchical carambola-like LTO-TiO 2 composite is a promising anode material for high-power and long-life lithium-ion batteries.

A mesoporous WO3−X/graphene composite as a high-performance Li-ion battery anode

International Nuclear Information System (INIS)

Liu, Fei; Kim, Jong Gu; Lee, Chul Wee; Im, Ji Sun

2014-01-01

Graphical abstract: The highly flexible and conductive graphene layer can enhance electron transfer, protect metal oxides against disintegration and aggregation and buffer the strain induced by volume expansion during cycles. The mesoporous surface layer provides an open network for Li+ diffusion. - Highlights: • Novel cocktail effects of 2D mesoporous WO 3−X /graphene for lithium ion battery. • New approach for lithium ion battery by easy and unique synthesis method. • Mechanism study with proper data for understanding a reaction on anode surface. - Abstract: A novel mesoporous WO 3−X /graphene composite was developed. This material allowed rapid electron and Li + ion diffusion when used as a Li-ion battery (LIB) anode material. Remarkably, the graphene support protected WO 3−X from changing volume during the electrochemical cycling process; this process generally induces capacity loss. The current work describes a high-performance anode material for LIB that has highly dense WO 3−X , as well as high capacity, rate capability and stability

Recent progress in understanding of the ion composition in the magnetosphere and some major question mark

International Nuclear Information System (INIS)

Hultqvist, B.

1981-06-01

The observations of the energetic ion composition in the magnetosphere are reviewed with the emphasis on the recent measurements by means of GEOS-1 and -2, ISEE-1 and 2, PROGNOZ-7 and SCATHA. The observations are compared with the predictions of the open magnetosphere model. One of the major conclusions is that there are processes in the magnetosphere which play a much larger part than the model, as hitherto presented, predicts. Direct ejection of ionospheric ions, in combination with acceleration, along closed as well as open field lines may even be the dominating source process for the ring current/inner plasma sheet in magnetic storms. In very disturbed conditions this ejection mechanism must work over most of the hemispheres poleward of say 50degrees. Circulation of the ionospheric ions through the tail of the magnetosphere is not likely to be of primary importance for the energization of these ions in very disturbed conditions. (author)

Microsatellite D21D210 (GT-12) allele frequencies in sporadic Alzheimer`s disease

Energy Technology Data Exchange (ETDEWEB)

Lannfelt, L; Lilius, L; Viitanen, M; Winblad, B; Basun, H [Huddinge Hospital, Karolinska Institute, Dept. of Geriatric Medicine, (Sweden); Houlden, H; Rossor, M [St. Mary` s Hospital, Dept. of Neurology, Medical School, London (United Kingdom); Hardy, J [University of South Florida, Suncoast Alzheimer` s Disease Research Labs, Department of Psychiatry, Tampa (United States)

1995-02-01

Four disease-causing mutations have so far been described in the amyloid precursor protein gene on chromosome 21 in familial early-onset Alzheimer`s disease. Linkage analysis with a fourteen-allele microsatellite at D21S210 named GT-12 has proven useful in the elucidation of amyloid presursor protein gene involvement in Alzheimer`s disease families, as it is closely linked to the gene. Most cases of Alzheimer`s disease are thought to be sporadic and not familial. However, evidence from earlier studies suggests an important genetic contribution also in sporadic cases, where gene-environment interaction may contribute to the disease. We have determined frequencies of the GT-12 alleles in 78 Swedish and 49 British sporadic Alzheimer`s disease cases and 104 healthy elderly control subjects, to investigate if the disease associates with a particular genotype in GT-12. However, no differences in allele frequencies were observed between any of the groups. (au) (26 refs.).

Molecular profile and copy number analysis of sporadic colorectal cancer in Taiwan

Directory of Open Access Journals (Sweden)

Li Ling-Hui

2011-06-01

Full Text Available Abstract Background Colorectal cancer (CRC is a major health concern worldwide, and recently becomes the most common cancer in Asia. The case collection of this study is one of the largest sets of CRC in Asia, and serves as representative data for investigating genomic differences between ethnic populations. We took comprehensive and high-resolution approaches to compare the clinicopathologic and genomic profiles of microsatellite instability (MSI vs. microsatellite stability (MSS in Taiwanese sporadic CRCs. Methods 1,173 CRC tumors were collected from the Taiwan population, and sequencing-based microsatellite typing assay was used to determine MSI and MSS. Genome-wide SNP array was used to detect CN alterations in 16 MSI-H and 13 MSS CRCs and CN variations in 424 general controls. Gene expression array was used to evaluate the effects of CN alterations, and quantitative PCR methods were used to replicate the findings in independent clinical samples. Results These 1,173 CRC tumors can be classified into 75 high-frequency MSI (MSI-H (6.4%, 96 low-frequency MSI (8.2% and 1,002 MSS (85.4%. Of the 75 MSI-H tumors, 22 had a BRAF mutation and 51 showed MLH1 promoter hypermethylation. There were distinctive differences in the extent of CN alterations between CRC MSS and MSI-H subtypes (300 Mb vs. 42 Mb per genome, p-value Conclusions Sporadic CRCs with MSI-H displayed distinguishable clinicopathologic features, which differ from those of MSS. Genomic profiling of the two types of sporadic CRCs revealed significant differences in the extent and distribution of CN alterations in the cancer genome. More than half of expressed genes showing CN differences can directly contribute to their expressional diversities, and the biological functions of the genes associated with CN changes in sporadic CRCs warrant further investigation to establish their possible clinical implications.

Synthesis and optimization of tin dioxide/functionalized multi-walled carbon nanotube composites as anode in lithium-ion battery

Energy Technology Data Exchange (ETDEWEB)

Xu, Xiao-Bing; Geng, Hong-Zhang, E-mail: genghz@tjpu.edu.cn; Meng, Yan; Ding, Er-Xiong; Wang, Yan; Zhang, Ze-Chen; Wang, Wen-Yi

2015-03-01

In this paper, nanocomposite electrodes for rechargeable Lithium-ion battery composed of tin dioxide (SnO{sub 2}) and multi-walled carbon nanotubes (MWCNTs) were prepared using the chemical deposition method with a subsequent sintering process. The as-prepared hybrids were characterized by thermal gravimetric analysis, Fourier transform infrared spectroscopy, X-ray diffraction and transmission electron microscopy. The results showed that the size of pure SnO{sub 2} particles was ∼5 nm and hybrids presented a uniform dispersion of SnO{sub 2} nanoparticles on the surfaces of the MWCNTs. The electrochemical properties of the composites were researched through a cyclic voltammetry and a galvanostatic charge–discharge test. It was found that the electrochemical performance of the composite was strongly dependent on the content of MWCNTs in the composites. The SnO{sub 2}/MWCNT composite with 18.40 wt% MWCNTs gave the best performance, exhibiting a relatively higher reversible capacity of 475 mAh g{sup −1} and an extended capacity retention of 65% even after 30 cycles at a current density of 78.2 mA g{sup −1}. - Highlights: • SnO{sub 2}/MWCNT nanocomposites were prepared using chemical deposition method. • SnO{sub 2} nanoparticles presented a uniformly dispersion on the surfaces of MWCNTs. • SnO{sub 2}/MWCNT composite anode exhibited high reversible capacity for rechargeable Li-ion battery.

Synthesis and optimization of tin dioxide/functionalized multi-walled carbon nanotube composites as anode in lithium-ion battery

International Nuclear Information System (INIS)

Xu, Xiao-Bing; Geng, Hong-Zhang; Meng, Yan; Ding, Er-Xiong; Wang, Yan; Zhang, Ze-Chen; Wang, Wen-Yi

2015-01-01

In this paper, nanocomposite electrodes for rechargeable Lithium-ion battery composed of tin dioxide (SnO 2 ) and multi-walled carbon nanotubes (MWCNTs) were prepared using the chemical deposition method with a subsequent sintering process. The as-prepared hybrids were characterized by thermal gravimetric analysis, Fourier transform infrared spectroscopy, X-ray diffraction and transmission electron microscopy. The results showed that the size of pure SnO 2 particles was ∼5 nm and hybrids presented a uniform dispersion of SnO 2 nanoparticles on the surfaces of the MWCNTs. The electrochemical properties of the composites were researched through a cyclic voltammetry and a galvanostatic charge–discharge test. It was found that the electrochemical performance of the composite was strongly dependent on the content of MWCNTs in the composites. The SnO 2 /MWCNT composite with 18.40 wt% MWCNTs gave the best performance, exhibiting a relatively higher reversible capacity of 475 mAh g −1 and an extended capacity retention of 65% even after 30 cycles at a current density of 78.2 mA g −1 . - Highlights: • SnO 2 /MWCNT nanocomposites were prepared using chemical deposition method. • SnO 2 nanoparticles presented a uniformly dispersion on the surfaces of MWCNTs. • SnO 2 /MWCNT composite anode exhibited high reversible capacity for rechargeable Li-ion battery

A genome-wide investigation of copy number variation in patients with sporadic brain arteriovenous malformation.

Directory of Open Access Journals (Sweden)

Nasrine Bendjilali

Full Text Available Brain arteriovenous malformations (BAVM are clusters of abnormal blood vessels, with shunting of blood from the arterial to venous circulation and a high risk of rupture and intracranial hemorrhage. Most BAVMs are sporadic, but also occur in patients with Hereditary Hemorrhagic Telangiectasia, a Mendelian disorder caused by mutations in genes in the transforming growth factor beta (TGFβ signaling pathway.To investigate whether copy number variations (CNVs contribute to risk of sporadic BAVM, we performed a genome-wide association study in 371 sporadic BAVM cases and 563 healthy controls, all Caucasian. Cases and controls were genotyped using the Affymetrix 6.0 array. CNVs were called using the PennCNV and Birdsuite algorithms and analyzed via segment-based and gene-based approaches. Common and rare CNVs were evaluated for association with BAVM.A CNV region on 1p36.13, containing the neuroblastoma breakpoint family, member 1 gene (NBPF1, was significantly enriched with duplications in BAVM cases compared to controls (P = 2.2×10(-9; NBPF1 was also significantly associated with BAVM in gene-based analysis using both PennCNV and Birdsuite. We experimentally validated the 1p36.13 duplication; however, the association did not replicate in an independent cohort of 184 sporadic BAVM cases and 182 controls (OR = 0.81, P = 0.8. Rare CNV analysis did not identify genes significantly associated with BAVM.We did not identify common CNVs associated with sporadic BAVM that replicated in an independent cohort. Replication in larger cohorts is required to elucidate the possible role of common or rare CNVs in BAVM pathogenesis.

Cortical restricted diffusion as the predominant MRI finding in sporadic Creutzfeldt-Jakob disease

Energy Technology Data Exchange (ETDEWEB)

Talbott, Sabrina D.; Sattenberg, Ronald J.; Heidenreich, Jens O. (Dept. of Radiology, Univ. of Louisville, Louisville (United States)), e-mail: sdtalb02@gwise.louisville.edu; Plato, Brian M (Dept. of Neurology, Univ. of Louisville, Louisville (United States)); Parker, John (Dept. of Pathology and Laboratory Medicine, Univ. of Louisville, Louisville (United States))

2011-04-15

Creutzfeldt-Jakob disease is a rare and fatal neurodegenerative disorder with MR findings predominantly limited to the grey matter of the cortex and the basal ganglia. Sporadic Creutzfeldt-Jakob disease can produce a spectrum of MR imaging findings of the brain, most notably on DWI and FLAIR sequences. Involvement of the basal ganglia and neocortex is the most common finding, but isolated involvement of the cortex can also be seen. We describe the clinical history and MRI findings of three patients with sporadic Creutzfeldt-Jakob disease confirmed by brain biopsy or autopsy and review the literature of imaging manifestations of this disease

Cortical restricted diffusion as the predominant MRI finding in sporadic Creutzfeldt-Jakob disease

International Nuclear Information System (INIS)

Talbott, Sabrina D.; Sattenberg, Ronald J.; Heidenreich, Jens O.; Plato, Brian M; Parker, John

2011-01-01

Creutzfeldt-Jakob disease is a rare and fatal neurodegenerative disorder with MR findings predominantly limited to the grey matter of the cortex and the basal ganglia. Sporadic Creutzfeldt-Jakob disease can produce a spectrum of MR imaging findings of the brain, most notably on DWI and FLAIR sequences. Involvement of the basal ganglia and neocortex is the most common finding, but isolated involvement of the cortex can also be seen. We describe the clinical history and MRI findings of three patients with sporadic Creutzfeldt-Jakob disease confirmed by brain biopsy or autopsy and review the literature of imaging manifestations of this disease

Novel Genetic Variants of Sporadic Atrial Septal Defect (ASD) in a Chinese Population Identified by Whole-Exome Sequencing (WES).

Science.gov (United States)

Liu, Yong; Cao, Yu; Li, Yaxiong; Lei, Dongyun; Li, Lin; Hou, Zong Liu; Han, Shen; Meng, Mingyao; Shi, Jianlin; Zhang, Yayong; Wang, Yi; Niu, Zhaoyi; Xie, Yanhua; Xiao, Benshan; Wang, Yuanfei; Li, Xiao; Yang, Lirong; Wang, Wenju; Jiang, Lihong

2018-03-05

BACKGROUND Recently, mutations in several genes have been described to be associated with sporadic ASD, but some genetic variants remain to be identified. The aim of this study was to use whole-exome sequencing (WES) combined with bioinformatics analysis to identify novel genetic variants in cases of sporadic congenital ASD, followed by validation by Sanger sequencing. MATERIAL AND METHODS Five Han patients with secundum ASD were recruited, and their tissue samples were analyzed by WES, followed by verification by Sanger sequencing of tissue and blood samples. Further evaluation using blood samples included 452 additional patients with sporadic secundum ASD (212 male and 240 female patients) and 519 healthy subjects (252 male and 267 female subjects) for further verification by a multiplexed MassARRAY system. Bioinformatic analyses were performed to identify novel genetic variants associated with sporadic ASD. RESULTS From five patients with sporadic ASD, a total of 181,762 genomic variants in 33 exon loci, validated by Sanger sequencing, were selected and underwent MassARRAY analysis in 452 patients with ASD and 519 healthy subjects. Three loci with high mutation frequencies, the 138665410 FOXL2 gene variant, the 23862952 MYH6 gene variant, and the 71098693 HYDIN gene variant were found to be significantly associated with sporadic ASD (PASD (PASD, and supported the use of WES and bioinformatics analysis to identify disease-associated mutations.

Clinicopathologic factors identify sporadic mismatch repair-defective colon cancers

DEFF Research Database (Denmark)

Halvarsson, Britta; Anderson, Harald; Domanska, Katarina

2008-01-01

Identification of sporadic mismatch repair (MMR)-defective colon cancers is increasingly demanded for decisions on adjuvant therapies. We evaluated clinicopathologic factors for the identification of these prognostically favorable tumors. Histopathologic features in 238 consecutive colon cancers...... and excluded 61.5% of the tumors from MMR testing. This clinicopathologic index thus successfully selects MMR-defective colon cancers. Udgivelsesdato: 2008-Feb...

Differences in histological features and PD-L1 expression between sporadic microsatellite instability and Lynch-syndrome-associated disease in Japanese patients with colorectal cancer.

Science.gov (United States)

Yamada, Rin; Yamaguchi, Tatsuro; Iijima, Takeru; Wakaume, Rika; Takao, Misato; Koizumi, Koichi; Hishima, Tsunekazu; Horiguchi, Shin-Ichiro

2018-06-01

The field of immunotherapy has recently focused on cancers with microsatellite instability (MSI). These cancers include both Lynch-syndrome-associated tumors, which are caused by mismatch repair (MMR) germline mutations, and sporadic MSI tumors, which are mainly attributed to MLH1 promoter methylation. The present study aimed to clarify differences in the histological and PD-L1 expression profiles between these two types of MSI cancers in Japanese patients. Among 908 cases of colorectal cancer treated via surgical resection from 2008 to 2014, we identified 64 MSI cancers, including 36 sporadic MSI and 28 Lynch-syndrome-associated cancers, using a BRAF V600E mutation analysis and MLH1 methylation analysis. Of the latter subgroup, 21 (75%) harbored MMR germline mutations. The following were more frequent with sporadic MSI than with Lynch syndrome associated cancers: poor differentiation (50.0 vs. 7.1%, P = 0.0002), especially solid type (30.6 vs. 3.6%, P = 0.0061); medullary morphology (19.4 and 0%, P = 0.015), Crohn-like lymphoid reaction (50.0 vs. 25.0%, P = 0.042), and PD-L1 expression (25.0 vs. 3.6%, P = 0.034). However, the groups did not differ in terms of the mean invasive front and intratumoral CD8-positive cell densities. In a logistic regression analysis, PD-L1 expression correlated with poor differentiation (odds ratio: 7.65, 95% confidence interval: 1.55-37.7, P = 0.012), but not with the difference between sporadic MSI cancer and Lynch-syndrome-associated cancer (odds ratio: 4.74, 95% confidence interval: 0.50-45.0, P = 0.176). Therefore, compared with Lynch-syndrome-associated cancers, sporadic MSI cancers are more frequently solid, poorly differentiated medullary cancers that express PD-L1.

Fabrication and Characterization of SnO2/Graphene Composites as High Capacity Anodes for Li-Ion Batteries

Directory of Open Access Journals (Sweden)

Abirami Dhanabalan

2013-11-01

Full Text Available Tin-oxide and graphene (TG composites were fabricated using the Electrostatic Spray Deposition (ESD technique, and tested as anode materials for Li-ion batteries. The electrochemical performance of the as-deposited TG composites were compared to heat-treated TG composites along with pure tin-oxide films. The heat-treated composites exhibited superior specific capacity and energy density than both the as-deposited TG composites and tin oxide samples. At the 70th cycle, the specific capacities of the as-deposited and post heat-treated samples were 534 and 737 mA·h/g, respectively, and the corresponding energy densities of the as-deposited and heat-treated composites were 1240 and 1760 W·h/kg, respectively. This improvement in the electrochemical performance of the TG composite anodes as compared to the pure tin oxide samples is attributed to the synergy between tin oxide and graphene, which increases the electrical conductivity of tin oxide and helps alleviate volumetric changes in tin-oxide during cycling.

Molecular Cytogenetic Characterization Identified the Murine B-Cell Lymphoma Cell Line A-20 as a Model for Sporadic Burkitt's Lymphoma.

Science.gov (United States)

Guja, Karolina; Liehr, Thomas; Rincic, Martina; Kosyakova, Nadezda; Hussein Azawi, Shaymaa S

2017-11-01

Here, we report the first molecular cytogenetic characterization of the BALB/cAnN mouse derived B-cell non-Hodgkin lymphoma (B-cell NHL) cell lines A-20. Even though previously used as a model for testing of, for example, dexametason, up to present, no data in the genetic properties of A-20 were available. The present study closed this gap and provides evidence that A-20 is a model for B-cell NHL subgroup sporadic Burkitt's lymphoma. C-myc oncogene is involved in a translocation and copy number alterations as gain of murine 14q material could be observed. Interestingly, the cell line showed the karyotype 39,X,-X or -Y,t(2;15)(qE5;qD2),del(6)(qB3qC3),del(9)(qA3qA4),dup(14)(qE1qE4) in ~95% of the cells, being exceptionally stable for cell lines being established 38 years ago. Still, ~5% of the cells showed polyploidization followed by chromothripsis. It remains to be determined if this can be observed also in other cell lines, just has not been reported yet, and/or if it is a unique feature of A-20. Overall, finally here, the necessary genetic data to identify A-20 as a model for human sporadic Burkitt's lymphoma are provided.

Solvent transfer of graphene oxide for synthesis of tin mono-sulfide graphene composite and application as anode of lithium-ion battery

Energy Technology Data Exchange (ETDEWEB)

Tripathi, Alok M., E-mail: alokmani@iitb.ac.in; Mitra, Sagar

2016-11-15

Graphical abstract: Destabilization of graphene oxide colloid and SnS graphene composite preparation for lithium-ion battery. - Abstract: Tin mono sulfide (SnS) graphene composite has been synthesized for anode of lithium-ion battery. For synthesis of composite, graphene oxide (GO)-water (H{sub 2}O) colloid has been destabilized and ensured the complete transfer of graphene oxide into another organic solvent N, N-dimethyl formamide (DMF). Mechanism for the destabilization of GO-H{sub 2}O colloid is established. Surface to surface attachment of SnS on graphene sheet is achieved by solvothermal solution phase assembly of graphene sheets and SnS nanoparticles in DMF solvent. Graphene plays role in nanoparticle formation in composite. Such confined composite has been cycled reversibly at current rate of 160 mA g{sup −1}, in voltage region of 0.01–2.5 V and exhibit a superior discharge capacity of 630 mAh g{sup −1} after 50th cycle. Ex situ TEM analysis of used electrode reveal that the SnS nanoparticle-graphene composite with CMC binder perform better due to proper shape retention of electroactive materials during electrochemical cycling.

Solvent transfer of graphene oxide for synthesis of tin mono-sulfide graphene composite and application as anode of lithium-ion battery

International Nuclear Information System (INIS)

Tripathi, Alok M.; Mitra, Sagar

2016-01-01

Graphical abstract: Destabilization of graphene oxide colloid and SnS graphene composite preparation for lithium-ion battery. - Abstract: Tin mono sulfide (SnS) graphene composite has been synthesized for anode of lithium-ion battery. For synthesis of composite, graphene oxide (GO)-water (H_2O) colloid has been destabilized and ensured the complete transfer of graphene oxide into another organic solvent N, N-dimethyl formamide (DMF). Mechanism for the destabilization of GO-H_2O colloid is established. Surface to surface attachment of SnS on graphene sheet is achieved by solvothermal solution phase assembly of graphene sheets and SnS nanoparticles in DMF solvent. Graphene plays role in nanoparticle formation in composite. Such confined composite has been cycled reversibly at current rate of 160 mA g"−"1, in voltage region of 0.01–2.5 V and exhibit a superior discharge capacity of 630 mAh g"−"1 after 50th cycle. Ex situ TEM analysis of used electrode reveal that the SnS nanoparticle-graphene composite with CMC binder perform better due to proper shape retention of electroactive materials during electrochemical cycling.

Ion-beam doping of GaAs with low-energy (100 eV) C + using combined ion-beam and molecular-beam epitaxy

Science.gov (United States)

Iida, Tsutomu; Makita, Yunosuke; Kimura, Shinji; Winter, Stefan; Yamada, Akimasa; Fons, Paul; Uekusa, Shin-ichiro

1995-01-01

A combined ion-beam and molecular-beam-epitaxy (CIBMBE) system has been developed. This system consists of an ion implanter capable of producing ions in the energy range of 30 eV-30 keV and conventional solid-source MBE. As a successful application of CIBMBE, low-energy (100 eV) carbon ion (C+) irradiation during MBE growth of GaAs was carried out at substrate temperatures Tg between 500 and 590 °C. C+-doped layers were characterized by low-temperature (2 K) photoluminescence (PL), Raman scattering, and van der Pauw measurements. PL spectra of undoped GaAs grown by CIBMBE revealed that unintentional impurity incorporation into the epilayer is extremely small and precise doping effects are observable. CAs acceptor-related emissions such as ``g,'' [g-g], and [g-g]β are observed and their spectra are significantly changed with increasing C+ beam current density Ic. PL measurements showed that C atoms were efficiently incorporated during MBE growth by CIBMBE and were optically well activated as an acceptor in the as-grown condition even for Tg as low as 500 °C. Raman measurement showed negligible lattice damage of the epilayer bombarded with 100 eV C+ with no subsequent heat treatment. These results indicate that contamination- and damage-free impurity doping without postgrowth annealing can be achieved by the CIBMBE method.

Ion-beam doping of GaAs with low-energy (100 eV) C(+) using combined ion-beam and molecular-beam epitaxy

Science.gov (United States)

Lida, Tsutomu; Makita, Yunosuke; Kimura, Shinji; Winter, Stefan; Yamada, Akimasa; Fons, Paul; Uekusa, Shin-Ichiro

1995-01-01

A combined ion-beam and molecular-beam-epitaxy (CIBMBE) system has been developed. This system consists of an ion implanter capable of producing ions in the energy range of 30 eV - 30 keV and conventional solid-source MBE. As a successful application of CIBMBE, low-energy (100 eV) carbon ion (C(+)) irradiation during MBE growth of GaAs was carried out at substrate temperatures T(sub g) between 500 and 590 C. C(+)-doped layers were characterized by low-temperature (2 K) photoluminescence (PL), Raman scattering, and van der Pauw measurements. PL spectra of undoped GaAs grown by CIBMBE revealed that unintentional impurity incorporation into the epilayer is extremely small and precise doping effects are observable. C(sub As) acceptor-related emissions such as 'g', (g-g), and (g-g)(sub beta) are observed and their spectra are significantly changed with increasing C(+) beam current density I(sub c). PL measurements showed that C atoms were efficiently incorporated during MBE growth by CIBMBE and were optically well activated as an acceptor in the as-grown condition even for T(sub g) as low as 500 C. Raman measurement showed negligible lattice damage of the epilayer bombarded with 100 eV C(+) with no subsequent heat treatment. These results indicate that contamination- and damage-free impurity doping without postgrowth annealing can be achieved by the CIBMBE method.

Measuring sporadic gastrointestinal illness associated with drinking water - an overview of methodologies.

Science.gov (United States)

Bylund, John; Toljander, Jonas; Lysén, Maria; Rasti, Niloofar; Engqvist, Jannes; Simonsson, Magnus

2017-06-01

There is an increasing awareness that drinking water contributes to sporadic gastrointestinal illness (GI) in high income countries of the northern hemisphere. A literature search was conducted in order to review: (1) methods used for investigating the effects of public drinking water on GI; (2) evidence of possible dose-response relationship between sporadic GI and drinking water consumption; and (3) association between sporadic GI and factors affecting drinking water quality. Seventy-four articles were selected, key findings and information gaps were identified. In-home intervention studies have only been conducted in areas using surface water sources and intervention studies in communities supplied by ground water are therefore needed. Community-wide intervention studies may constitute a cost-effective alternative to in-home intervention studies. Proxy data that correlate with GI in the community can be used for detecting changes in the incidence of GI. Proxy data can, however, not be used for measuring the prevalence of illness. Local conditions affecting water safety may vary greatly, making direct comparisons between studies difficult unless sufficient knowledge about these conditions is acquired. Drinking water in high-income countries contributes to endemic levels of GI and there are public health benefits for further improvements of drinking water safety.

One-Pot Synthesis of CoSex -rGO Composite Powders by Spray Pyrolysis and Their Application as Anode Material for Sodium-Ion Batteries.

Science.gov (United States)

Park, Gi Dae; Kang, Yun Chan

2016-03-14

A simple one-pot synthesis of metal selenide/reduced graphene oxide (rGO) composite powders for application as anode materials in sodium-ion batteries was developed. The detailed mechanism of formation of the CoSe(x)-rGO composite powders that were selected as the first target material in the spray pyrolysis process was studied. The crumple-structured CoSe(x)-rGO composite powders prepared by spray pyrolysis at 800 °C had a crystal structure consisting mainly of Co0.85 Se with a minor phase of CoSe2. The bare CoSe(x) powders prepared for comparison had a spherical shape and hollow structure. The discharge capacities of the CoSe(x)-rGO composite and bare CoSe(x) powders in the 50th cycle at a constant current density of 0.3 A g(-1) were 420 and 215 mA h g(-1), respectively, and their capacity retentions measured from the second cycle were 80 and 46%, respectively. The high structural stability of the CoSe(x)-rGO composite powders for repeated sodium-ion charge and discharge processes resulted in superior sodium-ion storage properties compared to those of the bare CoSe(x) powders. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hierarchical shell/core CuO nanowire/carbon fiber composites as binder-free anodes for lithium-ion batteries

International Nuclear Information System (INIS)

Yuan, Wei; Luo, Jian; Pan, Baoyou; Qiu, Zhiqiang; Huang, Shimin; Tang, Yong

2017-01-01

Highlights: •The composite anode is composed of CuO nanowire shell and carbon fiber core. •The composite anode avoids completely the use of binders. •Synergistic effect of carbon fibers and CuO nanowires enhances performance. •Carbon fibers improve electrical conductivity and buffer volume change. •CuO nanowires shorten diffusion length and alleviate structural strain. -- Abstract: Developing high-performance electrode structures is of great importance for advanced lithium-ion batteries. This study reports an efficient method to fabricate hierarchical shell/core CuO nanowire/carbon fiber composites via electroless plating and thermal oxidation processes. With this method, a binder-free CuO nanowire/carbon fiber shell/core hierarchical network composite anode for lithium-ion batteries is successfully fabricated. The morphology and chemical composition of the anode are characterized, and the electrochemical performance of the anode is investigated by standard electrochemical tests. Owing to the superior properties of carbon fibers and the morphological advantages of CuO nanowires, this composite anode still retains an excellent reversible capacity of 598.2 mAh g −1 with a capacity retention rate above 86%, even after 50 cycles, which is much higher than the CuO anode without carbon fibers. Compared to the typical CuO/C electrode systems, the novel binder-free anode yields a performance close to that of the typical core/shell electrode systems and a much higher reversible capacity and capacity retention than the similar shell/core patterns as well as the anodes with binders. It is believed that this novel anode will pave the way to the development of binder-free anodes in response to the increasing demands for high-power energy storage.

Ion beam enhancement in magnetically insulated ion diodes for high-intensity pulsed ion beam generation in non-relativistic mode

Energy Technology Data Exchange (ETDEWEB)

Zhu, X. P. [Key Laboratory of Materials Modification by Laser, Ion, and Electron Beams, Ministry of Education, Dalian University of Technology, Dalian 116024 (China); Surface Engineering Laboratory, School of Materials Science and Engineering, Dalian University of Technology, Dalian 116024 (China); Zhang, Z. C.; Lei, M. K., E-mail: surfeng@dlut.edu.cn [Surface Engineering Laboratory, School of Materials Science and Engineering, Dalian University of Technology, Dalian 116024 (China); Pushkarev, A. I. [Surface Engineering Laboratory, School of Materials Science and Engineering, Dalian University of Technology, Dalian 116024 (China); Laboratory of Beam and Plasma Technology, High Technologies Physics Institute, Tomsk Polytechnic University, 30, Lenin Ave, 634050 Tomsk (Russian Federation)

2016-01-15

High-intensity pulsed ion beam (HIPIB) with ion current density above Child-Langmuir limit is achieved by extracting ion beam from anode plasma of ion diodes with suppressing electron flow under magnetic field insulation. It was theoretically estimated that with increasing the magnetic field, a maximal value of ion current density may reach nearly 3 times that of Child-Langmuir limit in a non-relativistic mode and close to 6 times in a highly relativistic mode. In this study, the behavior of ion beam enhancement by magnetic insulation is systematically investigated in three types of magnetically insulated ion diodes (MIDs) with passive anode, taking into account the anode plasma generation process on the anode surface. A maximal enhancement factor higher than 6 over the Child-Langmuir limit can be obtained in the non-relativistic mode with accelerating voltage of 200–300 kV. The MIDs differ in two anode plasma formation mechanisms, i.e., surface flashover of a dielectric coating on the anode and explosive emission of electrons from the anode, as well as in two insulation modes of external-magnetic field and self-magnetic field with either non-closed or closed drift of electrons in the anode-cathode (A-K) gap, respectively. Combined with ion current density measurement, energy density characterization is employed to resolve the spatial distribution of energy density before focusing for exploring the ion beam generation process. Consistent results are obtained on three types of MIDs concerning control of neutralizing electron flows for the space charge of ions where the high ion beam enhancement is determined by effective electron neutralization in the A-K gap, while the HIPIB composition of different ion species downstream from the diode may be considerably affected by the ion beam neutralization during propagation.

An excellent performance anode of ZnFe2O4/flake graphite composite for lithium ion battery

International Nuclear Information System (INIS)

Yao, Lingmin; Hou, Xianhua; Hu, Shejun; Tang, Xiaoqin; Liu, Xiang; Ru, Qiang

2014-01-01

Highlights: • ZnFe 2 O 4 /flake graphite composite was synthesized by hydrothermal method. • The ZnFe 2 O 4 /flake graphite anode demonstrated high initial coulombic efficiency of 87.7%. • The initial discharge /charge capacity was 848 mA h g −1 and 744 mA h g −1 . • The high capacity retention of 98% was obtained for the ZnFe 2 O 4 /flake graphite anode. -- Abstract: An approach of hydrothermal reaction for lithium ion battery was adopted, by which ZnFe 2 O 4 /flake graphite composites with excellent performance could be prepared as anode materials for lithium ion batteries. With nano-sized ZnFe 2 O 4 particles coating on the electrochemical active matrix of flake graphite, the special composites allowed improved electronic conductivity and constructed an expressway for the transport of charges and lithium ions. Thus the ZnFe 2 O 4 /flake graphite anode became a compromise between capacity and cycle ability. The initial discharge–charge capacity was 848 mA h g −1 and 744 mA h g −1 at a constant current density of 100 mA g −1 , respectively. As high as 87.7% of the initial coulombic efficiency was obtained. Additionally, the charge capacity maintained constantly in the range of 720–735 mA h g −1 in following cycles. And a high reversible charge capacity of 730 mA h g −1 could be attained after 100 cycles, with the reversible capacity retention of 98%

SARC006: Phase II Trial of Chemotherapy in Sporadic and Neurofibromatosis Type 1 Associated Chemotherapy-Naive Malignant Peripheral Nerve Sheath Tumors

Directory of Open Access Journals (Sweden)

Christine S. Higham

2017-01-01

Full Text Available Background. Worse chemotherapy response for neurofibromatosis type 1- (NF1- associated compared to sporadic malignant peripheral nerve sheath tumors (MPNST has been reported. Methods. We evaluated the objective response (OR rate of patients with AJCC Stage III/IV chemotherapy-naive NF1 MPNST versus sporadic MPNST after 4 cycles of neoadjuvant chemotherapy, 2 cycles of ifosfamide/doxorubicin, and 2 cycles of ifosfamide/etoposide. A Simon optimal two-stage design was used (target response rate 40%. Results. 34 NF1 (median age 33 years and 14 sporadic (median age 40 years MPNST patients enrolled. Five of 28 (17.9% evaluable NF1 MPNST patients had a partial response (PR, as did 4 of 9 (44.4% patients with sporadic MPNST. Stable disease (SD was achieved in 22 NF1 and 4 sporadic MPNST patients. In both strata, results in the initial stages met criteria for expansion of enrollment. Only 1 additional PR was observed in the expanded NF1 stratum. Enrollment was slower than expected and the trial closed before full accrual. Conclusions. This trial was not powered to detect differences in response rates between NF1 and sporadic MPNST. While the OR rate was lower in NF1 compared to sporadic MPNST, qualitative responses were similar, and disease stabilization was achieved in most patients.

Plasma-surface interaction at sharp edges and corners during ion-assisted physical vapor deposition. Part I: Edge-related effects and their influence on coating morphology and composition

International Nuclear Information System (INIS)

Macak, E.B.; Muenz, W.-D.; Rodenburg, J.M.

2003-01-01

Ion-assisted physical vapor deposition (PVD) is a common industrial method for growing thin coatings of various interstitial nitride alloys. The interaction between the ions and three-dimensional nonflat samples during the deposition can, however, lead to unwanted local changes in the properties of the coating and thus its performance. We analyze the characteristics of the ion bombardment during ion-assisted PVD on sharp convex substrates and their effect on the growing coating. We show that the magnitude and the spatial extent of the edge-related changes are directly related to the characteristics of the plasma sheath around the biased edges. We examine the influence of the edge geometry and the deposition conditions. The edge-related effects are studied on the example of wedge-shaped samples coated with TiAlN/VN by closed-field unbalanced magnetron deposition process using high-flux low-energy Ar + -ion irradiation (J i /J me ∼4, E i =75-150 eV). The samples are analyzed by scanning electron microscopy and energy-dispersive x-ray spectroscopy. Significant changes in the morphology, thickness, and composition of the coatings are found in the edge region. In order to account for the changes, we apply a self-consistent model of the plasma sheath around wedge-shaped samples proposed by Watterson [J. Phys. D 22, 1300 (1989)], to our conditions. For a 30 deg. wedge coated at -150 V, the resputtering rate in the edge region is found to be increased by up to ten times as compared to flat substrate areas. The effect is due to the combined action of an increased ion flux and increased sputtering yield as a result of the nonperpendicular angle of incidence of ions in the edge region. The situation at sharp corners, where even more severe effects are observed, is analyzed and modeled in the companion article E. B. Macak et al., J. Appl. Phys. (2003) (Part II)

MRI of sporadic Creutzfeldt-Jakob disease

International Nuclear Information System (INIS)

Kong, A.; Vliet, A. Van der.

2008-01-01

Full text: The key MRI findings in five cases of sporadic Creutzfeldt-Jakob disease (CJD) are illustrated with four 'definite' and one 'probable' according to World Health Organization criteria. Close attention to fluid-attenuation inversion recovery and diffusion-weighted imaging sequences are important for diagnosis, noting especially restricted diffusion in cortical and deep grey matter. Our study and those of others show predominant cortical, caudate and thalamic involvement. This pattern is highly sensitive and specific for the diagnosis. Fluid-attenuation inversion recovery and diffusion-weighted imaging signal abnormality becomes progressively more extensive and bilateral as disease progresses, but may become less pronounced in end-stage disease because of atrophy.

MnO{sub 2} nanorods/3D-rGO composite as high performance anode materials for Li-ion batteries

Energy Technology Data Exchange (ETDEWEB)

Liu, Hongdong; Hu, Zhongli; Su, Yongyao; Ruan, Haibo; Hu, Rong [Research Institute for New Materials Technology, Chongqing University of Arts and Sciences, Chongqing 402160 (China); Zhang, Lei, E-mail: leizhang0215@126.com [College of Life Science, Chongqing Normal University, Chongqing 401331 (China)

2017-01-15

Highlights: • MnO{sub 2} nanorods/3D-rGO composite has been synthesized by a simple in situ hydrothermal methord. • MnO{sub 2} nanorods/3D-rGO composite exhibits high reversible capacity, outstanding rate capacity and excellent cyclic stability. • Building metal oxides/3D-rGO composite is an effective way for improving the electrochemical performance of Li-ion batteries. - Abstract: MnO{sub 2} nanorods/three-dimensional reduced graphene oxide (3D-rGO) composite has been synthesized by a simple in situ hydrothermal methord. The X-ray diffraction (XRD) pattern of the as-prepared composite reveals tetragonal structure of α-MnO{sub 2.} Raman spectroscopic and X-ray photoelectron spectroscopy (XPS) of the samples confirm the coexistence of MnO{sub 2} and graphene. The Brunauer-Emmett-Teller (BET) analysis shows the large surface area of the composite. The electron microscopy images of the as-synthesized products reveals the MnO{sub 2} nanorods are homogeneously grown on 3D-rGO matrix. Electrochemical characterization exhibits the MnO{sub 2} nanorods/3D-rGO composite with large reversible capacity (595 mA h g{sup −1} over 60 cycles at 100 mA g{sup −1}), high coulombic efficiency (above 99%), excellent rate capability and good cyclic stability. The superior electrochemical performance can be attributed to the turf-like nanostructure of composite, high capacity of MnO{sub 2} and superior electrical conductivity of 3D-rGO. It suggests that MnO{sub 2} nanorods/3D-rGO composite will be a promising anode material for Li-ion batteries.

Sporadic Endolymphatic Sac Tumor-A Very Rare Cause of Hearing Loss, Tinnitus, and Dizziness

DEFF Research Database (Denmark)

Schnack, Didde Trærup; Kiss, Katalin; Hansen, Søren

2017-01-01

Sporadic endolymphatic sac tumor is a very rare neoplasm. It is low malignant, locally destructive and expansive, but non-metastasizing. The tumor is very rare in the sporadic form, but more often associated with Von Hippel-Lindau disease. A 65-year old man with left sided tinnitus and hearing loss......-operative freeze-microscopy showed inflammation tissue, whereas subsequent microscopy showed papillary-cystic endolymphatic sac tumor. Endolymphatic sac tumor is a rare neoplasm. The tumor may present with asymmetrically sensory neural hearing loss with or without tinnitus, dizziness and facial nerve paresis...

Distribution of O+ ions in the plasma sheet and locations of substorm onsets

Science.gov (United States)

Ono, Y.; Christon, S. P.; Frey, H. U.; Lui, A. T. Y.

2010-09-01

We discuss the effect of O+ ions on substorm onsets by examining the relation between the substorm onset location and the distribution of the O+/H+ number density ratio before the onset in the various regions within the plasma sheet (-8 RE > XGSM > -32 RE). We use 9-212 keV/e ion flux data observed by Geotail/Energetic Particles and Ion Composition (EPIC)/Suprathermal Ion Composition Spectrometer (STICS) instrument and the IMAGE/Far Ultra-Violet (FUV) substorm onset list presented by Frey et al. [Frey, H. U., S. B. Mende, V. Angelopoulos, and E. F. Donovan (2004), Substorm onset observations by IMAGE-FUV, J. Geophys. Res., 109, A10304, doi:10.1029/2004JA010607]. The results are summarized as follows. Substorm onsets, which we identify by auroral initial brightenings, are likely to occur in the more dusk-(dawn-)ward region when the O+/H+ number density ratio is high in the dusk (dawn) side. This property is observed only in the near-Earth plasma sheet (at -8 RE > XGSM > -14 RE). The above-mentioned property holds in each of two groups: substorm events due to internal instability of the magnetosphere (i.e., internally triggered substorms) and events due to external changes in the solar wind or the interplanetary magnetic field (i.e., externally triggered substorms). Thus, we conclude that the substorm onset location depends on the density of O+ ions in the near-Earth plasma sheet prior to onset, whether the substorm is triggered internally or externally.

Physical function and muscle strength in sporadic inclusion body myositis

DEFF Research Database (Denmark)

Jørgensen, Anders N; Aagaard, Per; Nielsen, Jakob L

2017-01-01

INTRODUCTION: In this study, self-reported physical function, functional capacity, and isolated muscle function were investigated in sporadic inclusion body myositis (sIBM) patients. METHODS: The 36-item Short Form (SF-36) Health Survey and 2-min walk test (2MWT), timed up & go test (TUG), and 30-s...

Advanced carbon materials/olivine LiFePO4 composites cathode for lithium ion batteries

Science.gov (United States)

Gong, Chunli; Xue, Zhigang; Wen, Sheng; Ye, Yunsheng; Xie, Xiaolin

2016-06-01

In the past two decades, LiFePO4 has undoubtly become a competitive candidate for the cathode material of the next-generation LIBs due to its abundant resources, low toxicity and excellent thermal stability, etc. However, the poor electronic conductivity as well as low lithium ion diffusion rate are the two major drawbacks for the commercial applications of LiFePO4 especially in the power energy field. The introduction of highly graphitized advanced carbon materials, which also possess high electronic conductivity, superior specific surface area and excellent structural stability, into LiFePO4 offers a better way to resolve the issue of limited rate performance caused by the two obstacles when compared with traditional carbon materials. In this review, we focus on advanced carbon materials such as one-dimensional (1D) carbon (carbon nanotubes and carbon fibers), two-dimensional (2D) carbon (graphene, graphene oxide and reduced graphene oxide) and three-dimensional (3D) carbon (carbon nanotubes array and 3D graphene skeleton), modified LiFePO4 for high power lithium ion batteries. The preparation strategies, structure, and electrochemical performance of advanced carbon/LiFePO4 composite are summarized and discussed in detail. The problems encountered in its application and the future development of this composite are also discussed.

Sporadic adult onset primary torsion dystonia is a genetic disorder by the temporal discrimination test.

LENUS (Irish Health Repository)

Kimmich, Okka

2012-02-01

Adult-onset primary torsion dystonia is an autosomal dominant disorder with markedly reduced penetrance; patients with sporadic adult-onset primary torsion dystonia are much more prevalent than familial. The temporal discrimination threshold is the shortest time interval at which two stimuli are detected to be asynchronous and has been shown to be abnormal in adult-onset primary torsion dystonia. The aim was to determine the frequency of abnormal temporal discrimination thresholds in patients with sporadic adult-onset primary torsion dystonia and their first-degree relatives. We hypothesized that abnormal temporal discrimination thresholds in first relatives would be compatible with an autosomal dominant endophenotype. Temporal discrimination thresholds were examined in 61 control subjects (39 subjects <50 years of age; 22 subjects >50 years of age), 32 patients with sporadic adult-onset primary torsion dystonia (cervical dystonia n = 30, spasmodic dysphonia n = 1 and Meige\\'s syndrome n = 1) and 73 unaffected first-degree relatives (36 siblings, 36 offspring and one parent) using visual and tactile stimuli. Z-scores were calculated for all subjects; a Z > 2.5 was considered abnormal. Abnormal temporal discrimination thresholds were found in 1\\/61 (2%) control subjects, 27\\/32 (84%) patients with adult-onset primary torsion dystonia and 32\\/73 (44%) unaffected relatives [siblings (20\\/36; 56%), offspring (11\\/36; 31%) and one parent]. When two or more relatives were tested in any one family, 22 of 24 families had at least one first-degree relative with an abnormal temporal discrimination threshold. The frequency of abnormal temporal discrimination thresholds in first-degree relatives of patients with sporadic adult-onset primary torsion dystonia is compatible with an autosomal dominant disorder and supports the hypothesis that apparently sporadic adult-onset primary torsion dystonia is genetic in origin.

Sporadic adult onset primary torsion dystonia is a genetic disorder by the temporal discrimination test.

Science.gov (United States)

Kimmich, Okka; Bradley, David; Whelan, Robert; Mulrooney, Nicola; Reilly, Richard B; Hutchinson, Siobhan; O'Riordan, Sean; Hutchinson, Michael

2011-09-01

Adult-onset primary torsion dystonia is an autosomal dominant disorder with markedly reduced penetrance; patients with sporadic adult-onset primary torsion dystonia are much more prevalent than familial. The temporal discrimination threshold is the shortest time interval at which two stimuli are detected to be asynchronous and has been shown to be abnormal in adult-onset primary torsion dystonia. The aim was to determine the frequency of abnormal temporal discrimination thresholds in patients with sporadic adult-onset primary torsion dystonia and their first-degree relatives. We hypothesized that abnormal temporal discrimination thresholds in first relatives would be compatible with an autosomal dominant endophenotype. Temporal discrimination thresholds were examined in 61 control subjects (39 subjects 50 years of age), 32 patients with sporadic adult-onset primary torsion dystonia (cervical dystonia n = 30, spasmodic dysphonia n = 1 and Meige's syndrome n = 1) and 73 unaffected first-degree relatives (36 siblings, 36 offspring and one parent) using visual and tactile stimuli. Z-scores were calculated for all subjects; a Z > 2.5 was considered abnormal. Abnormal temporal discrimination thresholds were found in 1/61 (2%) control subjects, 27/32 (84%) patients with adult-onset primary torsion dystonia and 32/73 (44%) unaffected relatives [siblings (20/36; 56%), offspring (11/36; 31%) and one parent]. When two or more relatives were tested in any one family, 22 of 24 families had at least one first-degree relative with an abnormal temporal discrimination threshold. The frequency of abnormal temporal discrimination thresholds in first-degree relatives of patients with sporadic adult-onset primary torsion dystonia is compatible with an autosomal dominant disorder and supports the hypothesis that apparently sporadic adult-onset primary torsion dystonia is genetic in origin.

CpG methylation of APC promoter 1A in sporadic and familial breast cancer patients.

Science.gov (United States)

Debouki-Joudi, Saoussen; Trifa, Fatma; Khabir, Abdelmajid; Sellami-Boudawara, Tahia; Frikha, Mounir; Daoud, Jamel; Mokdad-Gargouri, Raja

2017-01-01

Tumour suppressor gene (TSG) silencing through promoter hypermethylation plays an important role in cancer initiation. The aim of this study was to assess the extent of methylation of APC gene promoter in 91 sporadic and 44 familial cases of Tunisian patients with breast cancer (BC) in. The frequency of APC promoter methylation is somewhat similar for sporadic and familial breast cancer cases, (52.1%, and 54.5% respectively). For sporadic breast cancer patients, there was a significant correlation of APC promoter hypermethylation with TNM stage (p = 0.024) and 3-year survival (p = 0.025). Regarding the hormonal status (HR), we found significant association between negativity to PR and unmethylated APC (p= 0.005) while ER and Her2/neu are not correlated. Moreover, unmethylated APC promoter is more frequent in tumours expressing at least one out the 3 proteins compared to triple negative cases (p= 0.053). On the other hand, aberrant methylation of APC was associated with tumour size (p = 0.036), lymph node (p = 0.028), distant metastasis (p = 0.031), and 3-year survival (p = 0.046) in the group of patients with familial breast cancer. Moreover, patients with sporadic breast cancer displaying the unmethylated profile have a significant prolonged overall survival compared to those with the methylated pattern of APC promoter (p log rank = 0.008). Epigenetic change at the CpG islands in the APC promoter was associated with the silence of its transcript and the loss of protein expression suggesting that this event is the main mechanism regulating the APC expression in breast cancer. In conclusion, our data showed that the loss of APC through aberrant methylation is associated with the aggressive behavior of both sporadic and familial breast cancer in Tunisian patients.

Low-energy plasma immersion ion implantation to induce DNA transfer into bacterial E. coli

Energy Technology Data Exchange (ETDEWEB)

Sangwijit, K. [Biotechnology Unit, University of Phayao, Muang, Phayao 56000 (Thailand); Yu, L.D., E-mail: yuld@thep-center.org [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand); Sarapirom, S. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Faculty of Science, Maejo University, Bang Khen, Chiang Mai 50290 (Thailand); Pitakrattananukool, S. [School of Science, University of Phayao, Muang, Phayao 56000 (Thailand); Anuntalabhochai, S. [Biotechnology Unit, University of Phayao, Muang, Phayao 56000 (Thailand)

2015-12-15

Plasma immersion ion implantation (PIII) at low energy was for the first time applied as a novel biotechnology to induce DNA transfer into bacterial cells. Argon or nitrogen PIII at low bias voltages of 2.5, 5 and 10 kV and fluences ranging from 1 × 10{sup 12} to 1 × 10{sup 17} ions/cm{sup 2} treated cells of Escherichia coli (E. coli). Subsequently, DNA transfer was operated by mixing the PIII-treated cells with DNA. Successes in PIII-induced DNA transfer were demonstrated by marker gene expressions. The induction of DNA transfer was ion-energy, fluence and DNA-size dependent. The DNA transferred in the cells was confirmed functioning. Mechanisms of the PIII-induced DNA transfer were investigated and discussed in terms of the E. coli cell envelope anatomy. Compared with conventional ion-beam-induced DNA transfer, PIII-induced DNA transfer was simpler with lower cost but higher efficiency.

Self-assembly silicon/porous reduced graphene oxide composite film as a binder-free and flexible anode for lithium-ion batteries

International Nuclear Information System (INIS)

Tang, H.; Zhang, Y.J.; Xiong, Q.Q.; Cheng, J.D.; Zhang, Q.; Wang, X.L.; Gu, C.D.; Tu, J.P.

2015-01-01

A Si/porous reduced graphene oxide (rGO) composite film synthesized by evaporation and leavening method are developed as a high-performance anode material for lithium ion batteries. The porous structure as buffer base can effectively release the volume expansion of the silicon particles, increase the electrical conductivity and reduce the transfer resistance of Li ions. The Si/porous rGO composite film presents high specific capacity and good cycling stability (1261 mA h g −1 at 50 mA g −1 up to 70 cycles), as well as enhanced rate capability. This approach to prepare such a unique structure is a low-cost and facile route for the silicon-based anode materials

Freestanding rGO-SWNT-STN Composite Film as an Anode for Li Ion Batteries with High Energy and Power Densities

Directory of Open Access Journals (Sweden)

Taeseup Song

2015-12-01

Full Text Available Freestanding Si-Ti-Ni alloy particles/reduced graphene oxide/single wall carbon nanotube composites have been prepared as an anode for lithium ion batteries via a simple filtration method. This composite electrode showed a 9% increase in reversible capacity, a two-fold higher cycle retention at 50 cycles and a two-fold higher rate capability at 2 C compared to pristine Si-Ti-Ni (STN alloy electrodes. These improvements were attributed to the suppression of the pulverization of the STN active material by the excellent mechanical properties of the reduced graphene oxide-single wall carbon nanotube networks and the enhanced kinetics associated with both electron and Li ion transport.

Modification of composite por -Si/SnOx power ion beam of nanosecond duration

International Nuclear Information System (INIS)

Korusenko, P.M.; Bolotov, V.V.; Knyazev, E.V.; Kovivchak, V.S.; Korepanov, A.A.; Nesov, S.N.; Povoroznyuk, S.N.

2011-01-01

The results of XPS (X-ray photoelectron spectroscopy), AES (Auger electron spectroscopy) and SEM (Scanning electron microscopy) investigation of tin oxide nanolayers on the samples of the composite por-Si/SnO x with different porosity of the matrix, formed under the influence of a powerful ion beam of nanosecond duration was presented. It is shown that fast melting and crystallization of the surface leads to the formation of globular structures with a typical size of 200 nm. Established that the tin is included in structure of the nanocomposite in the oxidized state with little inclusion of metallic β-tin. With increasing porosity, phase composition of nanolayers of tin is close to the state corresponding to the higher tin oxide SnO 2 . Also shows that with increasing porosity, the intensity of subvalent 4d lines of tin, which is apparently associated with an increased degree of hybridization of the tin atoms and oxygen atoms. According to the results stratified etching was to evaluate the changes of the elemental structure of the composite and the depth of penetration of tin. (authors)

Effects of exotic composite bosons in e+e- scattering at 50--100 GeV

International Nuclear Information System (INIS)

Akama, K.; Hattori, T.; Yasue, M.

1990-01-01

We show that some of the neutral exotics in the composite model decouple from neutrinos at low energies, and can be as light as the mass scale of the weak interactions, offering the possibility of detecting sizable effects in e + e - scattering at 50--100 GeV

A three-dimensional LiFePO4/carbon nanotubes/graphene composite as a cathode material for lithium-ion batteries with superior high-rate performance

International Nuclear Information System (INIS)

Lei, Xingling; Zhang, Haiyan; Chen, Yiming; Wang, Wenguang; Ye, Yipeng; Zheng, Chuchun; Deng, Peng; Shi, Zhicong

2015-01-01

Graphical abstract: The excellent electrochemical performances can be attributed to the synergistic effect of CNTs and graphene. - Highlights: • The LFP–CNT–G composite was successfully prepared by solid station method. • The interlaced CNTs reduced the crumple of graphene and improved tap density of the composite. • The LFP–CNT–G electrode exhibited superior electrochemical performance. - Abstract: A three-dimensional lithium iron phosphate (LiFePO 4 )/carbon nanotubes (CNTs)/graphene composite was successfully synthesized via solid-state reaction. The LiFePO 4 /carbon nanotubes/graphene (LFP–CNT–G) composite used as Li-ions battery cathode material exhibits superior high-rate capability and favorable charge–discharge cycle performance under relative high current density compared with that of LiFePO 4 /carbon nanotubes (LFP–CNT) composite and LiFePO 4 /graphene (LFP–G) composite. Graphene nanosheets and CNTs construct 3D conducting networks are favor for faster electron transfer, higher Li-ions diffusion coefficient and lower resistance during the Li-ions reversible reaction. The synergistic effect of graphene nanosheets and CNTs improves the rate capability and cycling stability of LiFePO 4 -based cathodes. The LFP–CNT–G electrode shows reversible capacity of 168.9 mA h g −1 at 0.2 C and 115.8 mA h g −1 at 20 C. The electrochemical impedance spectroscopy demonstrate that the LFP–CNT–G electrode has the smallest charge-transfer resistance, indicating that the fast electron transfer from the electrolyte to the LFP–CNT–G active materials in the Li-ions intercalation/deintercalation reactions owing to the three-dimensional networks of graphene and carbon nanotubes

High-energy high-luminosity electron-ion collider eRHIC

International Nuclear Information System (INIS)

Litvinenko, V.N.; Ben-Zvi, I.; Hammons, L.; Hao, Y.; Webb, S.

2011-01-01

In this paper, we describe a future electron-ion collider (EIC), based on the existing Relativistic Heavy Ion Collider (RHIC) hadron facility, with two intersecting superconducting rings, each 3.8 km in circumference. The replacement cost of the RHIC facility is about two billion US dollars, and the eRHIC will fully take advantage and utilize this investment. We plan adding a polarized 5-30 GeV electron beam to collide with variety of species in the existing RHIC accelerator complex, from polarized protons with a top energy of 325 GeV, to heavy fully-striped ions with energies up to 130 GeV/u. Brookhaven's innovative design, is based on one of the RHIC's hadron rings and a multi-pass energy-recovery linac (ERL). Using the ERL as the electron accelerator assures high luminosity in the 10 33 -10 34 cm -2 sec -1 range, and for the natural staging of eRHIC, with the ERL located inside the RHIC tunnel. The eRHIC will provide electron-hadron collisions in up to three interaction regions. We detail the eRHIC's performance in Section 2. Since first paper on eRHIC paper in 2000, its design underwent several iterations. Initially, the main eRHIC option (the so-called ring-ring, RR, design) was based on an electron ring, with the linac-ring (LR) option as a backup. In 2004, we published the detailed 'eRHIC 0th Order Design Report' including a cost-estimate for the RR design. After detailed studies, we found that an LR eRHIC has about a 10-fold higher luminosity than the RR. Since 2007, the LR, with its natural staging strategy and full transparency for polarized electrons, became the main choice for eRHIC. In 2009, we completed technical studies of the design and dynamics for MeRHIC with 3-pass 4 GeV ERL. We learned much from this evaluation, completed a bottom-up cost estimate for this $350M machine, but then shelved the design. In the same year, we turned again to considering the cost-effective, all-in-tunnel six-pass ERL for our design of the high-luminosity eRHIC. In it

MAVEN SupraThermal and Thermal Ion Compostion (STATIC) Instrument

Science.gov (United States)

McFadden, J. P.; Kortmann, O.; Curtis, D.; Dalton, G.; Johnson, G.; Abiad, R.; Sterling, R.; Hatch, K.; Berg, P.; Tiu, C.; Gordon, D.; Heavner, S.; Robinson, M.; Marckwordt, M.; Lin, R.; Jakosky, B.

2015-12-01

The MAVEN SupraThermal And Thermal Ion Compostion (STATIC) instrument is designed to measure the ion composition and distribution function of the cold Martian ionosphere, the heated suprathermal tail of this plasma in the upper ionosphere, and the pickup ions accelerated by solar wind electric fields. STATIC operates over an energy range of 0.1 eV up to 30 keV, with a base time resolution of 4 seconds. The instrument consists of a toroidal "top hat" electrostatic analyzer with a 360° × 90° field-of-view, combined with a time-of-flight (TOF) velocity analyzer with 22.5° resolution in the detection plane. The TOF combines a -15 kV acceleration voltage with ultra-thin carbon foils to resolve H+, He^{++}, He+, O+, O2+, and CO2+ ions. Secondary electrons from carbon foils are detected by microchannel plate detectors and binned into a variety of data products with varying energy, mass, angle, and time resolution. To prevent detector saturation when measuring cold ram ions at periapsis (˜10^{1 1} eV/cm2 s sr eV), while maintaining adequate sensitivity to resolve tenuous pickup ions at apoapsis (˜103 eV/cm2 s sr eV), the sensor includes both mechanical and electrostatic attenuators that increase the dynamic range by a factor of 103. This paper describes the instrument hardware, including several innovative improvements over previous TOF sensors, the ground calibrations of the sensor, the data products generated by the experiment, and some early measurements during cruise phase to Mars.

CT and MRI in iatrogenic and sporadic Creutzfeldt-Jakob disease: as far as imaging perseives

Energy Technology Data Exchange (ETDEWEB)

Garcia Santos, J.M. [Servicio de Radiodiagnostico, HU Dr. Morales Meseguer, Murcia (Spain)]|[Section of Neuroradiology, HU Virgen de la Arrixaca, Murcia (Spain); Lopez Corbalan, J.A. [Section of Neuroradiology, HU Virgen de la Arrixaca, Murcia (Spain); Martinez-Lage, J.F. [Service of Neurosurgery, HU Virgen de la Arrixaca, Murcia (Spain); Sicilis Guillen, J. [Service of Neurology, HU Virgen de la Arrixaca, Murcia (Spain)

1996-04-01

Creutzfeldt-Jakob Disease (CJD), an invariably fatal dementing illness, affects patients in middle and old age (sporadic form). However, the association of CJD with certain treatments (iatrogenic form) has been described in younger patients. The clinical onset of the two forms seems to differ; in the iatrogenic form a high frequency of the ataxic CJD variant has been reported. Nowadays, a definitive diagnosis of CJD is exclusively histological. We present five cases of CJD, one sporadic and the others iatrogenic, following dura mater grafts and analyse their CT and MRI features. CT typically demonstrates brain atrophy, generally progressive, but in sporadic CJD midfield MRI also showed abnormal signal, with predominant deep grey matter involvement. The use of narrow windows with proton-density sequences may reveal subtle cortical signal abnormalities not clearly visible with conventional windows. The early demonstration of these changes, in the appropriate clinical context, may suggest CJD and this supports the use of mid- or high magnetic fields in the diagnosis of CJD and other forms of dementia. In our cases of iatrogenic CJD, low-field MRI did not reveal more than the progressive atrophy displayed by CT, and raises the question on the one hand of possible differences, based on imaging, from the sporadic form, and on the other of the lack of sensitivity of low-field magnets to signal changes in CJD. (orig.)

CT and MRI in iatrogenic and sporadic Creutzfeldt-Jakob disease: as far as imaging perseives

International Nuclear Information System (INIS)

Garcia Santos, J.M.; Lopez Corbalan, J.A.; Martinez-Lage, J.F.; Sicilis Guillen, J.

1996-01-01

Creutzfeldt-Jakob Disease (CJD), an invariably fatal dementing illness, affects patients in middle and old age (sporadic form). However, the association of CJD with certain treatments (iatrogenic form) has been described in younger patients. The clinical onset of the two forms seems to differ; in the iatrogenic form a high frequency of the ataxic CJD variant has been reported. Nowadays, a definitive diagnosis of CJD is exclusively histological. We present five cases of CJD, one sporadic and the others iatrogenic, following dura mater grafts and analyse their CT and MRI features. CT typically demonstrates brain atrophy, generally progressive, but in sporadic CJD midfield MRI also showed abnormal signal, with predominant deep grey matter involvement. The use of narrow windows with proton-density sequences may reveal subtle cortical signal abnormalities not clearly visible with conventional windows. The early demonstration of these changes, in the appropriate clinical context, may suggest CJD and this supports the use of mid- or high magnetic fields in the diagnosis of CJD and other forms of dementia. In our cases of iatrogenic CJD, low-field MRI did not reveal more than the progressive atrophy displayed by CT, and raises the question on the one hand of possible differences, based on imaging, from the sporadic form, and on the other of the lack of sensitivity of low-field magnets to signal changes in CJD. (orig.)

The P413L chromogranin B variation in French patients with sporadic amyotrophic lateral sclerosis.

Science.gov (United States)

Blasco, Hélène; Corcia, Philippe; Veyrat-Durebex, Charlotte; Coutadeur, Cathleen; Fournier, Clémentine; Camu, William; Gordon, Paul; Praline, Julien; Andres, Christian R; Vourc'h, Patrick

2011-05-01

Chromogranins interact with mutant forms of superoxide dismutase 1 (SOD1) responsible for a portion of familial amyotrophic lateral sclerosis (ALS). A particular variation (P413L) in the chromogranin B gene, CHGB, has been recently associated with an earlier age at onset in both familial and sporadic ALS. The aim of our study was to evaluate the P413L chromogranin variation in French patients with sporadic amyotrophic lateral sclerosis. We developed a High Resolution DNA Melting (HRM) protocol to analyse the P413L variation in the CHGB gene in 540 French patients with sporadic ALS and 504 controls. The clinical characteristics of patients were analysed in relation to their genotype. Results showed that our study on a large cohort of French-Caucasian patients with SALS and controls failed to confirm an increased frequency of the 413L variant in SALS patients. This frequency was 5.3% in the SALS population and 5.5% in the control group. Moreover, we did not observe a previous observation of a difference of age at onset between T-allele carriers and non-carriers (median age of onset 60.4 vs. 62.0 years of age, respectively). Thus, our findings do not support the 413L variant of rs742710 as a risk factor for sporadic ALS in the French population.

Solid-solution-like ZnO/C composites as excellent anode materials for lithium ion batteries

International Nuclear Information System (INIS)

Zhang, Guanhua; Zhang, Hang; Zhang, Xiang; Zeng, Wei; Su, Qingmei; Du, Gaohui; Duan, Huigao

2015-01-01

Exploring advanced anode materials to maximize the capacity of lithium ion batteries has been an active research area for decades. Constructing composites materials has been proved to be one of the most effective methods to achieve higher capacity due to the synergistic effect. In this work, we proposed and demonstrated a concept of solid-solution-like ZnO/C composites to approach the largest possible synergistic effect by introducing the most interfaces and minimizing the pulverization. The solid-solution-like ZnO/C electrode could achieve a high reversible capacity of 813.3 mAh g −1 at a current density of 100 mA g −1 after 100 cycles with a decrease rate of only 0.4% per cycle. Moreover, the discharge capacity still maintained 53.5% of the original value even when the current density increased to 40 times as much as the original, showing a distinguished rate performance. In addition, such solid-solution-like nanofibers can be easily prepared because of their compatibility with the existing industrial PAN-based spinning process. This may pave the way to mass produce lithium ion batteries with significantly enhanced performance using existing low-cost commercial facilities and recipes.

Oxide-Based Composite Electrolytes Using Na3Zr2Si2PO12/Na3PS4 Interfacial Ion Transfer.

Science.gov (United States)

Noi, Kousuke; Nagata, Yuka; Hakari, Takashi; Suzuki, Kenji; Yubuchi, So; Ito, Yusuke; Sakuda, Atsushi; Hayashi, Akitoshi; Tatsumisago, Masahiro

2018-05-31

All-solid-state sodium batteries using Na 3 Zr 2 Si 2 PO 12 (NASICON) solid electrolytes are promising candidates for safe and low-cost advanced rechargeable battery systems. Although NASICON electrolytes have intrinsically high sodium-ion conductivities, their high sintering temperatures interfere with the immediate development of high-performance batteries. In this work, sintering-free NASICON-based composites with Na 3 PS 4 (NPS) glass ceramics were prepared to combine the high grain-bulk conductivity of NASICON and the interfacial formation ability of NPS. Before the composite preparation, the NASICON/NPS interfacial resistance was investigated by modeling the interface between the NASICON sintered ceramic and the NPS glass thin film. The interfacial ion-transfer resistance was very small above room temperature; the area-specific resistances at 25 and 100 °C were 15.8 and 0.40 Ω cm 2 , respectively. On the basis of this smooth ion transfer, NASICON-rich (70-90 wt %) NASICON-NPS composite powders were prepared by ball-milling fine powders of each component. The composite powders were well-densified by pressing at room temperature. Scanning electron microscopy observation showed highly dispersed sub-micrometer NASICON grains in a dense NPS matrix to form closed interfaces between the oxide and sulfide solid electrolytes. The composite green (unfired) compacts with 70 and 80 wt % NASICON exhibited high total conductivities at 100 °C of 1.1 × 10 -3 and 6.8 × 10 -4 S cm -1 , respectively. An all-solid-state Na 15 Sn 4 /TiS 2 cell was constructed using the 70 wt % NASICON composite electrolyte by the uniaxial pressing of the powder materials, and its discharge properties were evaluated at 100 °C. The cell showed the reversible capacities of about 120 mAh g -1 under the current density of 640 μA cm -2 . The prepared oxide-based composite electrolytes were thus successfully applied in all-solid-state sodium rechargeable batteries without sintering.