WorldWideScience

Sample records for split s3 signal

  1. Crystal Splitting in the Growth of Bi2S3

    Energy Technology Data Exchange (ETDEWEB)

    Tang, Jing; Alivisatos, A. Paul

    2006-06-15

    Novel Bi{sub 2}S{sub 3} nanostructures with a sheaf-like morphology are obtained via reaction of bismuth acetate-oleic acid complex with elemental sulfur in 1-octadecence. We propose these structures form by the splitting crystal growth mechanism, which is known to account for the morphology some mineral crystals assume in nature. By controlling the synthetic parameters, different forms of splitting, analogous to observed in minerals, are obtained in our case of Bi{sub 2}S{sub 3}. These new and complex Bi{sub 2}S{sub 3} nanostructures are characterized by TEM, SEM, XRD and ED.

  2. Stacked Transformer for Driver Gain and Receive Signal Splitting

    Science.gov (United States)

    Driscoll, Kevin R.

    2013-01-01

    In a high-speed signal transmission system that uses transformer coupling, there is a need to provide increased transmitted signal strength without adding active components. This invention uses additional transformers to achieve the needed gain. The prior art uses stronger drivers (which require an IC redesign and a higher power supply voltage), or the addition of another active component (which can decrease reliability, increase power consumption, reduce the beneficial effect of serializer/deserializer preemphasis or deemphasis, and/or interfere with fault containment mechanisms), or uses a different transformer winding ratio (which requires redesign of the transformer and may not be feasible with high-speed signals that require a 1:1 winding ratio). This invention achieves the required gain by connecting the secondaries of multiple transformers in series. The primaries of these transformers are currently either connected in parallel or are connected to multiple drivers. There is also a need to split a receive signal to multiple destinations with minimal signal loss. Additional transformers can achieve the split. The prior art uses impedance-matching series resistors that cause a loss of signal. Instead of causing a loss, most instantiations of this invention would actually provide gain. Multiple transformers are used instead of multiple windings on a single transformer because multiple windings on the same transformer would require a redesign of the transformer, and may not be feasible with high-speed transformers that usually require a bifilar winding with a 1:1 ratio. This invention creates the split by connecting the primaries of multiple transformers in series. The secondary of each transformer is connected to one of the intended destinations without the use of impedance-matching series resistors.

  3. Computer-Assisted Traffic Engineering Using Assignment, Optimal Signal Setting, and Modal Split

    Science.gov (United States)

    1978-05-01

    Methods of traffic assignment, traffic signal setting, and modal split analysis are combined in a set of computer-assisted traffic engineering programs. The system optimization and user optimization traffic assignments are described. Travel time func...

  4. Laser Induced Breakdown Spectroscopy Based on Single Beam Splitting and Geometric Configuration for Effective Signal Enhancement

    OpenAIRE

    Yang, Guang; Lin, Qingyu; Ding, Yu; Tian, Di; Duan, Yixiang

    2015-01-01

    A new laser induced breakdown spectroscopy (LIBS) based on single-beam-splitting (SBS) and proper optical geometric configuration has been initially explored in this work for effective signal enhancement. In order to improve the interaction efficiency of laser energy with the ablated material, a laser beam operated in pulse mode was divided into two streams to ablate/excite the target sample in different directions instead of the conventional one beam excitation in single pulse LIBS (SP-LIBS)...

  5. Laser induced breakdown spectroscopy based on single beam splitting and geometric configuration for effective signal enhancement.

    Science.gov (United States)

    Yang, Guang; Lin, Qingyu; Ding, Yu; Tian, Di; Duan, Yixiang

    2015-01-05

    A new laser induced breakdown spectroscopy (LIBS) based on single-beam-splitting (SBS) and proper optical geometric configuration has been initially explored in this work for effective signal enhancement. In order to improve the interaction efficiency of laser energy with the ablated material, a laser beam operated in pulse mode was divided into two streams to ablate/excite the target sample in different directions instead of the conventional one beam excitation in single pulse LIBS (SP-LIBS). In spatial configuration, the laser beam geometry plays an important role in the emission signal enhancement. Thus, an adjustable geometric configuration with variable incident angle between the two splitted laser beams was constructed for achieving maximum signal enhancement. With the optimized angles of 60° and 70° for Al and Cu atomic emission lines at 396.15 nm and 324.75 nm respectively, about 5.6- and 4.8-folds signal enhancements were achieved for aluminum alloy and copper alloy samples compared to SP-LIBS. Furthermore, the temporal analysis, in which the intensity of atomic lines in SP-LIBS decayed at least ten times faster than the SBS-LIBS, proved that the energy coupling efficiency of SBS-LIBS was significantly higher than that of SP-LIBS.

  6. Laser Induced Breakdown Spectroscopy Based on Single Beam Splitting and Geometric Configuration for Effective Signal Enhancement

    Science.gov (United States)

    Yang, Guang; Lin, Qingyu; Ding, Yu; Tian, Di; Duan, Yixiang

    2015-01-01

    A new laser induced breakdown spectroscopy (LIBS) based on single-beam-splitting (SBS) and proper optical geometric configuration has been initially explored in this work for effective signal enhancement. In order to improve the interaction efficiency of laser energy with the ablated material, a laser beam operated in pulse mode was divided into two streams to ablate/excite the target sample in different directions instead of the conventional one beam excitation in single pulse LIBS (SP-LIBS). In spatial configuration, the laser beam geometry plays an important role in the emission signal enhancement. Thus, an adjustable geometric configuration with variable incident angle between the two splitted laser beams was constructed for achieving maximum signal enhancement. With the optimized angles of 60° and 70° for Al and Cu atomic emission lines at 396.15 nm and 324.75 nm respectively, about 5.6- and 4.8-folds signal enhancements were achieved for aluminum alloy and copper alloy samples compared to SP-LIBS. Furthermore, the temporal analysis, in which the intensity of atomic lines in SP-LIBS decayed at least ten times faster than the SBS-LIBS, proved that the energy coupling efficiency of SBS-LIBS was significantly higher than that of SP-LIBS. PMID:25557721

  7. Analysis of Information Contens and Stock Liquidity on the Companies Which Spliting Their Stock: Examination to Signaling and Trading Range on Jakarta Stock Exchange (Study on the Comanies Splitting Their Stock on the Year 200-2003)

    OpenAIRE

    Darmawan, Akhmad

    2007-01-01

    This research was held to examine signaling hypothesis by comparing the growth of companies profit which splitting their stock and not splitting their stock, on the period before stock splits and comparing yearly profit increase over 4 year before stock splits on the companies which splitting their stock. This research also conucted to examine trading range hypothesis by comparing market stock price the companies which splitting their stock and not splitting their stock split was done, and co...

  8. Effect of Rabi splitting on the low-temperature electron paramagnetic resonance signal of anthracite.

    Science.gov (United States)

    Fedaruk, Ryhor; Strzelczyk, Roman; Tadyszak, Krzysztof; Markevich, Siarhei A; Augustyniak-Jabłokow, Maria Aldona

    2017-01-01

    Specific distortions of the EPR signal of bulk anthracite are observed at low temperatures. They are accompanied by variations in the microwave oscillator frequency and are explained by the manifestation of the Rabi splitting due to the strong coupling between electron spins and the cavity, combined with the use of an automatic frequency-control (AFC) system. EPR signals are recorded at negligible saturation in the temperature range of 4-300K with use of the AFC system to keep the oscillator frequency locked to the resonant frequency of the TM110 cylinder cavity loaded with the sample. For the sample with a mass of 3.6mg the line distortions are observed below 50K and increase with temperature lowering. The oscillator frequency variations are used to estimate the coupling strength as well as the number of spins in the sample. It is shown that the spin-cavity coupling strength is inversely proportional to temperature and can be used for the absolute determination of the number of spins in a sample. Our results indicate that at low temperatures even 10 16 spins of the anthracite sample, with a mass of about 0.5mg, can distort the EPR line. Copyright © 2016 Elsevier Inc. All rights reserved.

  9. Signal transducer and activator of transcription 3 (STAT3) inhibitor, S3I-201, acts as a potent and non-selective alkylating agent.

    Science.gov (United States)

    Ball, Daniel P; Lewis, Andrew M; Williams, Declan; Resetca, Diana; Wilson, Derek J; Gunning, Patrick T

    2016-04-12

    The Signal Transducer and Activator of Transcription 3 (STAT3) oncogene is a master regulator of many human cancers, and a well-recognized target for therapeutic intervention. A well known STAT3 inhibitor, S3I-201 (NSC 74859), is hypothesized to block STAT3 function in cancer cells by binding the STAT3 SH2 domain and disrupt STAT3 protein complexation events. In this study, liquid chromatography tandem mass spectrometry analysis revealed that STAT3, in the presence of S3I-201, showed a minimum of five specific sites of modification, cysteine's 108, 259, 367, 542, and 687. Moreover, a prepared fluorescently labeled chemical probe of S3I-201 (DB-6-055) revealed that S3I-201 non-specifically and globally alkylated intracellular proteins at concentrations consistent with S3I-201's reported IC50. These data are consistent with the hypothesis that S3I-201 is a sub-optimal probe for interrogating STAT3-related cell biology.

  10. Molecule-binding dependent assembly of split aptamer and γ-cyclodextrin: A sensitive excimer signaling approach for aptamer biosensors

    Energy Technology Data Exchange (ETDEWEB)

    Jin, Fen [State Key Laboratory of Chemo/Biosensing and Chemometrics, College of Chemistry and Chemical Engineering, Hunan University, Changsha 410082 (China); Hubei Key Laboratory of Mine Environmental Pollution Control and Remediation, Environmental Science and Engineering College, Hubei Polytechnic University, Huangshi 435003 (China); Lian, Yan; Li, Jishan; Zheng, Jing; Hu, Yaping; Liu, Jinhua; Huang, Jin [State Key Laboratory of Chemo/Biosensing and Chemometrics, College of Chemistry and Chemical Engineering, Hunan University, Changsha 410082 (China); Yang, Ronghua, E-mail: Yangrh@pku.edu.cn [State Key Laboratory of Chemo/Biosensing and Chemometrics, College of Chemistry and Chemical Engineering, Hunan University, Changsha 410082 (China)

    2013-10-17

    Graphical abstract: Adenosine-binding aptamer was splitted into two fragments P2 and P3 which labeled pyrene molecules, mainly produce monomer signal. γ-CD cavity brings P2 and P3 in close proximity, allowing for weak excimer emission. In the presence of target, P2 and P3 are expected to bind ATP and form an aptamer/target complex, leads to large increase of the pyrene excimer fluorescence. -- Highlights: •We assembled split aptamer and γ-cyclodextrin fluorescence biosensors for ATP detection. •The biosensor increased quantum yield and emission lifetime of the excimer. •Time-resolved fluorescence is effective for ATP assay in complicated environment. -- Abstract: A highly sensitive and selective fluorescence aptamer biosensors for the determination of adenosine triphosphate (ATP) was developed. Binding of a target with splitting aptamers labeled with pyrene molecules form stable pyrene dimer in the γ-cyclodextrin (γ-CD) cavity, yielding a strong excimer emission. We have found that inclusion of pyrene dimer in γ-cyclodextrin cavity not only exhibits additive increases in quantum yield and emission lifetime of the excimer, but also facilitates target-induced fusion of the splitting aptamers to form the aptamer/target complex. As proof-of-principle, the approach was applied to fluorescence detection of adenosine triphosphate. With an anti-ATP aptamer, the approach exhibits excimer fluorescence response toward ATP with a maximum signal-to-background ratio of 32.1 and remarkably low detection limit of 80 nM ATP in buffer solution. Moreover, due to the additive fluorescence lifetime of excimer induced by γ-cyclodextrin, time-resolved measurements could be conveniently used to detect as low as 0.5 μM ATP in blood serum quantitatively.

  11. Toward Eco-Friendly and Highly Efficient Solar Water Splitting Using In2S3/Anatase/Rutile TiO2Dual-Staggered-Heterojunction Nanodendrite Array Photoanode.

    Science.gov (United States)

    Yang, Jih-Sheng; Wu, Jih-Jen

    2018-01-31

    The TiO 2 -based heterojunction nanodendrite (ND) array composed of anatase nanoparticles (ANPs) on the surface of the rutile ND (RND) array is selected as the model photoanode to demonstrate the strategies toward eco-friendly and efficient solar water splitting using neutral electrolyte and seawater. Compared with the performances in alkaline electrolyte, a non-negligible potential drop across the electrolyte as well as impeded charge injection and charge separation is monitored in the ANP/RND array photoanode with neutral electrolyte, which are, respectively, ascribed to the series resistance of neutral electrolyte, the fundamentally pH-dependent water oxidation mechanism on TiO 2 surface, as well as the less band bending at the interface of TiO 2 and neutral electrolyte. Accordingly, a TiO 2 -based dual-staggered heterojunction ND array photoanode is further designed in this work to overcome the issue of less band bending with the neutral electrolyte. The improvement of charge separation efficiency is realized by the deposition of a transparent In 2 S 3 layer on the ANP/RND array photoanode for constructing additional staggered heterojunction. Under illumination of AM 1.5G (100 mW cm -2 ), the improved photocurrent densities acquired both in neutral electrolyte and seawater at 1.23 V vs reversible hydrogen electrode (RHE), which approach the theoretical value for rutile TiO 2 , are demonstrated in the dual-staggered-heterojunction ND array photoanode. Faradaic efficiencies of ∼95 and ∼32% for solar water oxidation in neutral electrolyte and solar seawater oxidation for 2 h are acquired at 1.23 V vs RHE, respectively.

  12. Integrated Optimization of Speed Profiles and Power Split for a Tram with Hybrid Energy Storage Systems on a Signalized Route

    Directory of Open Access Journals (Sweden)

    Zhuang Xiao

    2018-02-01

    Full Text Available A tram with on-board hybrid energy storage systems based on batteries and supercapacitors is a new option for the urban traffic system. This configuration enables the tram to operate in both catenary zones and catenary-free zones, and the storage of regenerative braking energy for later usage. This paper presents a multiple phases integrated optimization (MPIO method for the coordination of speed profiles and power split considering the signal control strategy. The objective is to minimize the equivalent total energy consumption of all the power sources, which includes both the energy from the traction substation and energy storage systems. The constraints contain running time, variable gradients and curves, speed limits, power balance and signal time at some intersections. The integrated optimization problem is formulated as a multiple phases model based on the characters of the signalized route. An integrated calculation framework, using hp-adaptive pseudospectral method, is proposed for the integrated optimization problem. The effectiveness of the method is verified under fixed time signal (FTS control strategy and tram priority signal (TPS control strategy. Illustrative results show that this method can be successfully applied for trams with hybrid energy storage systems to improve their energy efficiency.

  13. Embryo splitting

    OpenAIRE

    Karl Illmensee; Mike Levanduski

    2010-01-01

    Mammalian embryo splitting has successfully been established in farm animals. Embryo splitting is safely and efficiently used for assisted reproduction in several livestock species. In the mouse, efficient embryo splitting as well as single blastomere cloning have been developed in this animal system. In nonhuman primates embryo splitting has resulted in several pregnancies. Human embryo splitting has been reported recently. Microsurgical embryo splitting under Institutional Review Board appr...

  14. Embryo splitting

    Directory of Open Access Journals (Sweden)

    Karl Illmensee

    2010-04-01

    Full Text Available Mammalian embryo splitting has successfully been established in farm animals. Embryo splitting is safely and efficiently used for assisted reproduction in several livestock species. In the mouse, efficient embryo splitting as well as single blastomere cloning have been developed in this animal system. In nonhuman primates embryo splitting has resulted in several pregnancies. Human embryo splitting has been reported recently. Microsurgical embryo splitting under Institutional Review Board approval has been carried out to determine its efficiency for blastocyst development. Embryo splitting at the 6–8 cell stage provided a much higher developmental efficiency compared to splitting at the 2–5 cell stage. Embryo splitting may be advantageous for providing additional embryos to be cryopreserved and for patients with low response to hormonal stimulation in assisted reproduction programs. Social and ethical issues concerning embryo splitting are included regarding ethics committee guidelines. Prognostic perspectives are presented for human embryo splitting in reproductive medicine.

  15. Double-staining chromogenic in situ hybridization as a useful alternative to split-signal fluorescence in situ hybridization in lymphoma diagnostics

    DEFF Research Database (Denmark)

    van Rijk, A.; Svenstroup-Poulsen, T.; Jones, M.

    2010-01-01

    , their detection is an important adjunct for increasing the reliability of the diagnosis. Recently, split-signal fluorescence hi situ hybridization has become available as a robust method to detect chromosomal breaks in paraffin-embedded formalin-fixed tissues. A bright field approach would bring this technology...... within the reach of every pathology laboratory. Design and Methods Our study was initiated to determine the consistency between chromogenic in situ hybridization and fluorescence in situ hybridization, both using split-signal probes developed for the detection of chromosomal breaks. Five hundred...... and forty cases of I I lymphoma entities and reactive, benign lymphoid tissues, collected from eight different pathology laboratories, placed on 1.5 fluorescence in situ hybridization pre-stained tissue microarray slides, were double stained for the chromogenic hybridization. For each core morphology...

  16. Immunoglobulin heavy-chain fluorescence in situ hybridization-chromogenic in situ hybridization DNA probe split signal in the clonality assessment of lymphoproliferative processes on cytological samples.

    Science.gov (United States)

    Zeppa, Pio; Sosa Fernandez, Laura Virginia; Cozzolino, Immacolata; Ronga, Valentina; Genesio, Rita; Salatiello, Maria; Picardi, Marco; Malapelle, Umberto; Troncone, Giancarlo; Vigliar, Elena

    2012-12-25

    The human immunoglobulin heavy-chain (IGH) locus at chromosome 14q32 is frequently involved in different translocations of non-Hodgkin lymphoma (NHL), and the detection of any breakage involving the IGH locus should identify a B-cell NHL. The split-signal IGH fluorescence in situ hybridization-chromogenic in situ hybridization (FISH-CISH) DNA probe is a mixture of 2 fluorochrome-labeled DNAs: a green one that binds the telomeric segment and a red one that binds the centromeric segment, both on the IGH breakpoint. In the current study, the authors tested the capability of the IGH FISH-CISH DNA probe to detect IGH translocations and diagnose B-cell lymphoproliferative processes on cytological samples. Fifty cytological specimens from cases of lymphoproliferative processes were tested using the split-signal IGH FISH-CISH DNA probe and the results were compared with light-chain assessment by flow cytometry (FC), IGH status was tested by polymerase chain reaction (PCR), and clinicohistological data. The signal score produced comparable results on FISH and CISH analysis and detected 29 positive, 15 negative, and 6 inadequate cases; there were 29 true-positive cases (66%), 9 true-negative cases (20%), 6 false-negative cases (14%), and no false-positive cases (0%). Comparing the sensitivity of the IGH FISH-CISH DNA split probe with FC and PCR, the highest sensitivity was obtained by FC, followed by FISH-CISH and PCR. The split-signal IGH FISH-CISH DNA probe is effective in detecting any translocation involving the IGH locus. This probe can be used on different samples from different B-cell lymphoproliferative processes, although it is not useful for classifying specific entities. Cancer (Cancer Cytopathol) 2012;. © 2012 American Cancer Society. Copyright © 2012 American Cancer Society.

  17. Aspects of Split Supersymmetry

    CERN Document Server

    Arkani-Hamed, N; Giudice, Gian Francesco; Romanino, A

    2005-01-01

    We explore some fundamental differences in the phenomenology, cosmology and model building of Split Supersymmetry compared with traditional low-scale supersymmetry. We show how the mass spectrum of Split Supersymmetry naturally emerges from theories where the dominant source of supersymmetry breaking preserves an $R$ symmetry, characterize the class of theories where the unavoidable $R$-breaking by gravity can be neglected, and point out a new possibility, where supersymmetry breaking is directly communicated at tree level to the visible sector via renormalizable interactions. Next, we discuss possible low-energy signals for Split Supersymmetry. The absence of new light scalars removes all the phenomenological difficulties of low-energy supersymmetry, associated with one-loop flavor and CP violating effects. However, the electric dipole moments of leptons and quarks do arise at two loops, and are automatically at the level of present limits with no need for small phases, making them accessible to several ongo...

  18. Splitting Descartes

    DEFF Research Database (Denmark)

    Schilhab, Theresa

    2007-01-01

    Kognition og Pædagogik vol. 48:10-18. 2003 Short description : The cognitivistic paradigm and Descartes' view of embodied knowledge. Abstract: That the philosopher Descartes separated the mind from the body is hardly news: He did it so effectively that his name is forever tied to that division....... But what exactly is Descartes' point? How does the Kartesian split hold up to recent biologically based learning theories?...

  19. On S3-equivariant homology

    Directory of Open Access Journals (Sweden)

    Mohamed Elhamdadi

    2001-01-01

    Full Text Available We prove that the group S3 (norm 1 quaternions cannot be a geometric realization of a crossed simplicial group and construct an exact sequence connecting S3-equivariant homology of an S3-space with its Pin(2-equivariant homology.

  20. 3-Mercaptopyruvate sulfurtransferase produces potential redox regulators cysteine- and glutathione-persulfide (Cys-SSH and GSSH) together with signaling molecules H2S2, H2S3and H2S.

    Science.gov (United States)

    Kimura, Yuka; Koike, Shin; Shibuya, Norihiro; Lefer, David; Ogasawara, Yuki; Kimura, Hideo

    2017-09-05

    Cysteine-persulfide (Cys-SSH) is a cysteine whose sulfhydryl group is covalently bound to sulfur (sulfane sulfur). Cys-SSH and its glutathione (GSH) counterpart (GSSH) have been recognized as redox regulators, some of which were previously ascribed to cysteine and GSH. However, the production of Cys-SSH and GSSH is not well understood. Here, we show that 3-mercaptopyruvate sulfurtransferase (3MST) produces Cys-SSH and GSSH together with the potential signaling molecules hydrogen per- and tri-sulfide (H 2 S 2 and H 2 S 3 ). Cys-SSH and GSSH are produced in the brain of wild-type mice but not in those of 3MST-KO mice. The levels of total persulfurated species in the brain of 3MST-KO mice are less than 50% of that in the brain of wild-type mice. Purified recombinant 3MST and lysates of COS cells expressing 3MST showed that Cys-SSH and GSSH were produced in the presence of physiological concentrations of cysteine and glutathione, while those with longer sulfur chains, Cys-SS n H and GSS n H, were produced in the presence of lower than physiological concentrations of cysteine and glutathione. The present study provides new insights into the production and physiological roles of these persulfurated species as well as the therapeutic targets for diseases in which these molecules are involved.

  1. Splitting strings on integrable backgrounds

    International Nuclear Information System (INIS)

    Vicedo, Benoit

    2011-05-01

    We use integrability to construct the general classical splitting string solution on R x S 3 . Namely, given any incoming string solution satisfying a necessary self-intersection property at some given instant in time, we use the integrability of the worldsheet σ-model to construct the pair of outgoing strings resulting from a split. The solution for each outgoing string is expressed recursively through a sequence of dressing transformations, the parameters of which are determined by the solutions to Birkhoff factorization problems in an appropriate real form of the loop group of SL 2 (C). (orig.)

  2. Standard Model Particles from Split Octonions

    Directory of Open Access Journals (Sweden)

    Gogberashvili M.

    2016-01-01

    Full Text Available We model physical signals using elements of the algebra of split octonions over the field of real numbers. Elementary particles are corresponded to the special elements of the algebra that nullify octonionic norms (zero divisors. It is shown that the standard model particle spectrum naturally follows from the classification of the independent primitive zero divisors of split octonions.

  3. Coded Splitting Tree Protocols

    DEFF Research Database (Denmark)

    Sørensen, Jesper Hemming; Stefanovic, Cedomir; Popovski, Petar

    2013-01-01

    This paper presents a novel approach to multiple access control called coded splitting tree protocol. The approach builds on the known tree splitting protocols, code structure and successive interference cancellation (SIC). Several instances of the tree splitting protocol are initiated, each...... instance is terminated prematurely and subsequently iterated. The combined set of leaves from all the tree instances can then be viewed as a graph code, which is decodable using belief propagation. The main design problem is determining the order of splitting, which enables successful decoding as early...... as possible. Evaluations show that the proposed protocol provides considerable gains over the standard tree splitting protocol applying SIC. The improvement comes at the expense of an increased feedback and receiver complexity....

  4. Split Cord Malformations

    Directory of Open Access Journals (Sweden)

    Yurdal Gezercan

    2015-06-01

    Full Text Available Split cord malformations are rare form of occult spinal dysraphism in children. Split cord malformations are characterized by septum that cleaves the spinal canal in sagittal plane within the single or duplicated thecal sac. Although their precise incidence is unknown, split cord malformations are exceedingly rare and represent %3.8-5 of all congenital spinal anomalies. Characteristic neurological, urological, orthopedic clinical manifestations are variable and asymptomatic course is possible. Earlier diagnosis and surgical intervention for split cord malformations is associated with better long-term fuctional outcome. For this reason, diagnostic imaging is indicated for children with associated cutaneous and orthopedic signs. Additional congenital anomalies usually to accompany the split cord malformations. Earlier diagnosis, meticuolus surgical therapy and interdisciplinary careful evaluation and follow-up should be made for good prognosis. [Cukurova Med J 2015; 40(2.000: 199-207

  5. Geometrical Applications of Split Octonions

    Directory of Open Access Journals (Sweden)

    Merab Gogberashvili

    2015-01-01

    Full Text Available It is shown that physical signals and space-time intervals modeled on split-octonion geometry naturally exhibit properties from conventional (3 + 1-theory (e.g., number of dimensions, existence of maximal velocities, Heisenberg uncertainty, and particle generations. This paper demonstrates these properties using an explicit representation of the automorphisms on split-octonions, the noncompact form of the exceptional Lie group G2. This group generates specific rotations of (3 + 4-vector parts of split octonions with three extra time-like coordinates and in infinitesimal limit imitates standard Poincare transformations. In this picture translations are represented by noncompact Lorentz-type rotations towards the extra time-like coordinates. It is shown how the G2 algebra’s chirality yields an intrinsic left-right asymmetry of a certain 3-vector (spin, as well as a parity violating effect on light emitted by a moving quantum system. Elementary particles are connected with the special elements of the algebra which nullify octonionic intervals. Then the zero-norm conditions lead to free particle Lagrangians, which allow virtual trajectories also and exhibit the appearance of spatial horizons governing by mass parameters.

  6. Split Malcev algebras

    Indian Academy of Sciences (India)

    project of the Spanish Ministerio de Educación y Ciencia MTM2007-60333. References. [1] Calderón A J, On split Lie algebras with symmetric root systems, Proc. Indian. Acad. Sci (Math. Sci.) 118(2008) 351–356. [2] Calderón A J, On split Lie triple systems, Proc. Indian. Acad. Sci (Math. Sci.) 119(2009). 165–177.

  7. A new signal-on method for the detection of protein based on binding-induced strategy and photoinduced electron transfer between Ag nanoclusters and split G-quadruplex-hemin complexes

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Kai, E-mail: zhangkai@jsinm.org; Wang, Ke; Zhu, Xue; Xie, Minhao

    2015-08-05

    Proteins play important roles in biological and cellular processes. The levels of proteins can be useful biomarkers for cellular events or disease diagnosis, thus the method for sensitive and selective detection of proteins is imperative to proteins express, study, and clinical diagnosis. Herein, we report a “signal-on” platform for the assay of protein based on binding-induced strategy and photoinduced electron transfer between Ag nanoclusters and split G-quadruplex-hemin complexes. By using biotin as the affinity ligand, this simple protocol could sensitively detect streptavidin with a detection limit down to 10 pM. With the use of an antibody as the affinity ligand, a method for homogeneous fluorescence detection of Prostate Specific Antigen (PSA) was also proposed with a detection limit of 10 pM. The one-step and wash-free assay showed good selectivity. Its high sensitivity, acceptable accuracy, and satisfactory versatility of analytes led to various applications in bioanalysis. - Highlights: • AgNCs have great potential for application in biomedicine. • Binding of two affinity ligands can result in binding-induced DNA assemblies. • PET can be happened between DNA/AgNCs and G-quadruplex/hemin complexes. • A platform for the detection of proteins was proposed by using PET and binding-induced strategy.

  8. Half-flat structures on S3×S3

    DEFF Research Database (Denmark)

    Madsen, Thomas Bruun; Salamon, Simon

    We classify left-invariant half-flat SU(3)-structures on S3 × S3, using the representation theory of SO(4) and matrix algebra. This leads to a systematic study of the associated cohomogeneity one Ricci-flat metrics with holonomy G2 obtained on 7-manifolds with equidistant S3 × S3 hypersurfaces...

  9. Split Malcev algebras

    Indian Academy of Sciences (India)

    We study the structure of split Malcev algebras of arbitrary dimension over an algebraically closed field of characteristic zero. We show that any such algebras is of the form M = U + ∑ j I j with U a subspace of the abelian Malcev subalgebra and any I j a well described ideal of satisfying [ I j , I k ] = 0 if ≠ .

  10. Splitting of Comets

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 7; Issue 1. Splitting of Comets. Utpal Mukhopadhyay. General Article Volume 7 Issue 1 January 2002 pp 11-22. Fulltext. Click here to view fulltext PDF. Permanent link: http://www.ias.ac.in/article/fulltext/reso/007/01/0011-0022. Keywords. Cometary ...

  11. Split warhead simultaneous impact

    Directory of Open Access Journals (Sweden)

    Rahul Singh Dhari

    2017-12-01

    Full Text Available A projectile system is proposed to improve efficiency and effectiveness of damage done by anti-tank weapon system on its target by designing a ballistic projectile that can split into multiple warheads and engage a target at the same time. This idea has been developed in interest of saving time consumed from the process of reloading and additional number of rounds wasted on target during an attack. The proposed system is achieved in three steps: Firstly, a mathematical model is prepared using the basic equations of motion. Second, An Ejection Mechanism of proposed warhead is explained with the help of schematics. Third, a part of numerical simulation which is done using the MATLAB software. The final result shows various ranges and times when split can be effectively achieved. With the new system, impact points are increased and hence it has a better probability of hitting a target.

  12. On split Lie triple systems

    Indian Academy of Sciences (India)

    We also introduced in [1] techniques of connection of roots in the framework of split Lie algebras. In the present paper we extend these techniques to the framework of split Lie triple systems so as to obtain a generalization of the results in [1]. We consider the wide class of split Lie triple systems (which contains the class of.

  13. Standardizing the segmentation index S-3

    NARCIS (Netherlands)

    Kiewiet, DJ; Achterkamp, M; Kratzer, J

    2004-01-01

    The segmentation index S-3 of Baerveldt and Snijders (1994) is used in the research of social cohesion. However, as is often the case with network level measures, the index is sensitive to network size and density. Therefore, networks of different size or density are not easily comparable. Of

  14. Spinning strings in AdS3×S3 with NS–NS flux

    Directory of Open Access Journals (Sweden)

    Rafael Hernández

    2014-11-01

    Full Text Available The sigma model describing closed strings rotating in AdS3×S3 is known to reduce to the one-dimensional Neumann–Rosochatius integrable system. In this article we show that closed spinning strings in AdS3×S3×T4 in the presence of NS–NS three-form flux can be described by an extension of the Neumann–Rosochatius system. We consider closed strings rotating with one spin in AdS3 and two different angular momenta in S3. For a class of solutions with constant radii we find the dependence of the classical energy on the spin and the angular momenta as an expansion in the square of the 't Hooft coupling of the theory.

  15. On the Rotating and Oscillating strings in $(AdS_3\\times S^3)_{\\varkappa}$

    CERN Document Server

    Banerjee, Aritra

    2014-01-01

    We study rigidly rotating strings in the $\\varkappa$-deformed $AdS_3 \\times S^3$ background. We find out two classes of solutions corresponding to the giant magnon and single spike solutions of the string rotating is two $S^2_{\\varkappa}$ subspace of rotations reduced along two different isometries. We verify that the dispersion relations reduce to the well known relation in the $\\varkappa\\rightarrow 0$ limit. We further study some oscillating string solutions in the $S^3_{\\varkappa}$ subspace.

  16. AdS3: the NHEK generation

    International Nuclear Information System (INIS)

    Bena, Iosif; Heurtier, Lucien; Puhm, Andrea

    2016-01-01

    It was argued in http://dx.doi.org/10.1007/JHEP03(2013)028 that the five-dimensional near-horizon extremal Kerr (NHEK) geometry can be embedded in String Theory as the infrared region of an infinite family of non-supersymmetric geometries that have D1, D5, momentum and KK monopole charges. We show that there exists a method to embed these geometries into asymptotically-AdS 3 ×S 3 /ℤ N solutions, and hence to obtain infinite families of flows whose infrared is NHEK. This indicates that the CFT dual to the NHEK geometry is the IR fixed point of a Renormalization Group flow from a known local UV CFT and opens the door to its explicit construction.

  17. The complete AdS_3 x S^3 x T^4 worldsheet S-matrix

    NARCIS (Netherlands)

    Borsato, Riccardo|info:eu-repo/dai/nl/370952170; Sax, Olof Ohlsson; Sfondrini, Alessandro|info:eu-repo/dai/nl/330983083; jr, Bogdan Stefanski

    2014-01-01

    We derive the non-perturbative worldsheet S matrix for fundamental excitations of Type IIB superstring theory on AdS_3 x S^3 x T^4 with Ramond-Ramond flux. To this end, we study the off-shell symmetry algebra of the theory and its representations. We use these to determine the S matrix up to scalar

  18. Methods of using (1S,3S)-3-amino-4-difluoromethylenyl-1-cyclopentanoic acid

    Energy Technology Data Exchange (ETDEWEB)

    Silverman, Richard B; Dewey, Stephen L; Miller, Steven

    2015-03-03

    (1S,3S)-3-amino-4-difluoromethylenyl-1-cyclopentanoic acid also known as CPP-115 or its pharmaceutically acceptable salts can be used to treat addiction and neurological disorders such as epilepsy without side effects such as visual field defects caused by vigabatrin (Sabril).

  19. Splitting methods for split feasibility problems with application to Dantzig selectors

    Science.gov (United States)

    He, Hongjin; Xu, Hong-Kun

    2017-05-01

    The split feasibility problem (SFP), which refers to the task of finding a point that belongs to a given nonempty, closed and convex set, and whose image under a bounded linear operator belongs to another given nonempty, closed and convex set, has promising applicability in modeling a wide range of inverse problems. Motivated by the increasingly data-driven regularization in the areas of signal/image processing and statistical learning, in this paper, we study the regularized split feasibility problem (RSFP), which provides a unified model for treating many real-world problems. By exploiting the split nature of the RSFP, we shall gainfully employ several efficient splitting methods to solve the model under consideration. A remarkable advantage of our methods lies in their easier subproblems in the sense that the resulting subproblems have closed-form representations or can be efficiently solved up to a high precision. As an interesting application, we apply the proposed algorithms for finding Dantzig selectors, in addition to demonstrating the effectiveness of the splitting methods through some computational results on synthetic and real medical data sets.

  20. The anticancer effect of (1S,2S,3E,7E,11E)-3,7,11, 15-cembratetraen-17,2-olide(LS-1) through the activation of TGF-β signaling in SNU-C5/5-FU, fluorouracil-resistant human colon cancer cells.

    Science.gov (United States)

    Kim, Eun-Ji; Kang, Jung-Il; Kwak, Jeon-Won; Jeon, Chan-Hee; Tung, Nguyen-Huu; Kim, Young-Ho; Choi, Cheol-Hee; Hyun, Jin-Won; Koh, Young-Sang; Yoo, Eun-Sook; Kang, Hee-Kyoung

    2015-03-16

    The anticancer effect of (1S,2S,3E,7E,11E)-3,7,11,15-cembratetraen-17,2-olide (LS-1) from Lobophytum sp. has been already reported in HT-29 human colorectal cancer cells. In this study, we examined the effect of LS-1 on the apoptosis induction of SNU-C5/5-FU, fluorouracil-resistant human colon cancer cells. Furthermore, we investigated whether the apoptosis-induction effect of LS-1 could arise from the activation of the TGF-β pathway. In SNU-C5/5-FU treated with LS-1 of 7.1 μM (IC50), we could observe the various apoptotic characteristics, such as the increase of apoptotic bodies, the increase of the sub-G1 hypodiploid cell population, the decrease of the Bcl-2 level, the increase of procaspase-9 cleavage, the increase of procaspase-3 cleavage and the increase of poly(ADP-ribose) polymerase cleavage. Interestingly, the apoptosis-induction effect of LS-1 was also accompanied by the increase of Smad-3 phosphorylation and the downregulation of c-Myc in SNU-C5/5-FU. LS-1 also increased the nuclear localization of phospho-Smad-3 and Smad-4. We examined whether LS-1 could downregulate the expression of carcinoembryonic antigen (CEA), a direct inhibitor of TGF-β signaling. LS-1 decreased the CEA level, as well as the direct interaction between CEA and TGF-βR1 in the apoptosis-induction condition of SNU-C5/5-FU. To examine whether LS-1 can induce apoptosis via the activation of TGF-β signaling, the SNU-C5/5-FU cells were treated with LS-1 in the presence or absence of SB525334, a TGF-βRI kinase inhibitor. SB525334 inhibited the effect of LS-1 on the apoptosis induction. These findings provide evidence demonstrating that the apoptosis-induction effect of LS-1 results from the activation of the TGF-β pathway via the downregulation of CEA in SNU-C5/5-FU.

  1. Evaluation report on SCTF-III test S3-3, S3-4 and S3-5

    International Nuclear Information System (INIS)

    Iguchi, Tadashi; Iwamura, Takamichi; Akimoto, Hajime; Okubo, Tsutomu; Ohnuki, Akira; Murao, Yoshio; Sakaki, Isao; Adachi, Hiromichi.

    1991-10-01

    In order to investigate the Counter Current Flow Limitation (CCFL) phenomena in full radius core, CCFL simulation tests (S3-3, S3-4 and S3-5) were performed using the Slab Core Test Facility (SCTF) Core-III. In these tests, the pressure in the pressure vessel was maintained at 0.3 MPa. Steam upflow was established in the core by injecting steam into the cold leg and water was injected into the upper plenum. Intact loops and pressure-vessel-side broken loop were closed to establish the steam upflow in the core. The break-through occurred in a localized region, while in the other region steam flowed up. Thus, the break-through occurrence was not uniform in full radius core. The radial break-through location was dependent mainly on the water subcooling distribution in the upper plenum. The break-through area decreased with decrease in steam injection rate. For typical PWR case, the ratio of the break-through area was approximately 20%. The break-through rate increased with the increase in the injected water subcooling and with the decrease in steam injection flow, similarly to small scale model tests. However, the quantitative relation between the break-through rate and the steam upflow rate was different from small scale model test. Two types of the relation were observed. When the steam upflow rate was high (corresponding to condition during early reflood phase), the break-through rate was nearly the same as one predicted with a typical one-dimensional CCFL correlation, indicating that the break-through behavior is almost one-dimensional even in a full radius core. However, when the steam upflow rate was decreased gradually (corresponding to condition during later reflood phase), the break-through rate increased suddenly at a certain steam upflow rate and could not be predicted with a typical one-dimensional CCFL correlation, indicating that the break-through behavior can switch to be nonuniform in full radius core. (J.P.N.)

  2. Split SUSY Radiates Flavor

    CERN Document Server

    Baumgart, Matthew; Zorawski, Thomas

    2014-01-01

    Radiative flavor models where the hierarchies of Standard Model (SM) fermion masses and mixings are explained via loop corrections are elegant ways to solve the SM flavor puzzle. Here we build such a model in the context of Mini-Split Supersymmetry (SUSY) where both flavor and SUSY breaking occur at a scale of 1000 TeV. This model is consistent with the observed Higgs mass, unification, and WIMP dark matter. The high scale allows large flavor mixing among the sfermions, which provides part of the mechanism for radiative flavor generation. In the deep UV, all flavors are treated democratically, but at the SUSY breaking scale, the third, second, and first generation Yukawa couplings are generated at tree level, one loop, and two loops, respectively. Save for one, all the dimensionless parameters in the theory are O(1), with the exception being a modest and technically natural tuning that explains both the smallness of the bottom Yukawa coupling and the largeness of the Cabibbo angle.

  3. How rivers split

    Science.gov (United States)

    Seybold, H. F.; Yi, R.; Devauchelle, O.; Petroff, A.; Rothman, D.

    2012-12-01

    River networks have fascinated mankind for centuries. They exhibit a striking geometry with similar shapes repeating on all scales. Yet, how these networks form and create these geometries remains elusive. Recently we have shown that channels fed by subsurface flow split at a characteristic angle of 2π/5 unambiguously consistent with our field measurements in a seepage network on the Florida Panhandle (Fig.1). Our theory is based only on the simple hypothesis that the channels grow in the direction at which the ground water enters the spring and classical solutions of subsurface hydrology. Here we apply our analysis to the ramification of large drainage basins and extend our theory to include slope effects. Using high resolution stream networks from the National Hydrography Dataset (NHD), we scrutinize our hypothesis in arbitrary channel networks and investigate the branching angle dependence on Horton-Strahler order and the maturity of the streams.; High-resolution topographic map of valley networks incised by groundwater flow, located on the Florida Panhandle near Bristol, FL.

  4. Split supersymmetry radiates flavor

    Science.gov (United States)

    Baumgart, Matthew; Stolarski, Daniel; Zorawski, Thomas

    2014-09-01

    Radiative flavor models where the hierarchies of Standard Model (SM) fermion masses and mixings are explained via loop corrections are elegant ways to solve the SM flavor puzzle. Here we build such a model in the context of mini-split supersymmetry (SUSY) where both flavor and SUSY breaking occur at a scale of 1000 TeV. This model is consistent with the observed Higgs mass, unification, and dark matter as a weakly interacting massive particle. The high scale allows large flavor mixing among the sfermions, which provides part of the mechanism for radiative flavor generation. In the deep UV, all flavors are treated democratically, but at the SUSY-breaking scale, the third, second, and first generation Yukawa couplings are generated at tree level, one loop, and two loops, respectively. Save for one, all the dimensionless parameters in the theory are O(1), with the exception being a modest and technically natural tuning that explains both the smallness of the bottom Yukawa coupling and the largeness of the Cabibbo angle.

  5. Global Locator, Local Locator, and Identifier Split (GLI-Split

    Directory of Open Access Journals (Sweden)

    Michael Menth

    2013-03-01

    Full Text Available The locator/identifier split is an approach for a new addressing and routing architecture to make routing in the core of the Internet more scalable. Based on this principle, we developed the GLI-Split framework, which separates the functionality of current IP addresses into a stable identifier and two independent locators, one for routing in the Internet core and one for edge networks. This makes routing in the Internet more stable and provides more flexibility for edge networks. GLI-Split can be incrementally deployed and it is backward-compatible with the IPv6 Internet. We describe its architecture, compare it to other approaches, present its benefits, and finally present a proof-of-concept implementation of GLI-Split.

  6. Split-illumination electron holography

    International Nuclear Information System (INIS)

    Tanigaki, Toshiaki; Aizawa, Shinji; Suzuki, Takahiro; Park, Hyun Soon; Inada, Yoshikatsu; Matsuda, Tsuyoshi; Taniyama, Akira; Shindo, Daisuke; Tonomura, Akira

    2012-01-01

    We developed a split-illumination electron holography that uses an electron biprism in the illuminating system and two biprisms (applicable to one biprism) in the imaging system, enabling holographic interference micrographs of regions far from the sample edge to be obtained. Using a condenser biprism, we split an electron wave into two coherent electron waves: one wave is to illuminate an observation area far from the sample edge in the sample plane and the other wave to pass through a vacuum space outside the sample. The split-illumination holography has the potential to greatly expand the breadth of applications of electron holography.

  7. Spiky strings on AdS3 x S3 with NS-NS flux

    CERN Document Server

    Banerjee, Aritra; Pradhan, Pabitra M.

    2014-01-01

    We study rigidly rotating strings in the background of AdS3 x S3 with Neveu-Schwarz (NS) fluxes. We find two interesting limiting cases corresponding to the known giant magnon and the new single spike solution of strings in the above background and write down the dispersion relations among various conserved charges. We use proper regularization to find the correct relations among them. We further study the circular and infinite spiky strings on AdS and study their properties.

  8. ISR split-field magnet

    CERN Multimedia

    CERN PhotoLab

    1975-01-01

    The experimental apparatus used at intersection 4 around the Split-Field Magnet by the CERN-Bologna Collaboration (experiment R406). The plastic scintillator telescopes are used for precise pulse-height and time-of-flight measurements.

  9. A Frequency Splitting Method For CFM Imaging

    DEFF Research Database (Denmark)

    Udesen, Jesper; Gran, Fredrik; Jensen, Jørgen Arendt

    2006-01-01

    The performance of conventional CFM imaging will often be degraded due to the relatively low number of pulses (4-10) used for each velocity estimate. To circumvent this problem we propose a new method using frequency splitting (FS). The FS method uses broad band chirps as excitation pulses instead...... of narrow band pulses as in conventional CFM imaging. By appropriate filtration, the returned signals are divided into a number of narrow band signals which are approximately disjoint. After clutter filtering the velocities are found from each frequency band using a conventional autocorrelation estimator....... Finally the velocity estimates from each frequency band are averaged to obtain an improved velocity estimate. The FS method has been evaluated in simulations using the Field II program and in flow phantom experiments using the experimental ultrasound scanner RASMUS. In both simulations and experiments...

  10. Split quaternions and semi-Euclidean projective spaces

    Energy Technology Data Exchange (ETDEWEB)

    Ata, Erhan [Department of Mathematics, Dumlupinar University, 43100 Kutahya (Turkey); Department of Mathematics, Ankara University, 06100 Ankara (Turkey)], E-mail: eata@dumlupinar.edu.tr; Yayli, Yusuf [Department of Mathematics, Dumlupinar University, 43100 Kutahya (Turkey); Department of Mathematics, Ankara University, 06100 Ankara (Turkey)

    2009-08-30

    In this study, we give one-to-one correspondence between the elements of the unit split three-sphere S(3,2) with the complex hyperbolic special unitary matrices SU(2,1). Thus, we express spherical concepts such as meridians of longitude and parallels of latitude on SU(2,1) by using the method given in Toth [Toth G. Glimpses of algebra and geometry. Springer-Verlag; 1998] for S{sup 3}. The relation among the special orthogonal group SO(R{sup 3}), the quotient group of unit quaternions S{sup 3}/{l_brace}{+-}1{r_brace} and the projective space RP{sup 3} given as SO(R{sup 3}){approx_equal}S{sup 3}/{l_brace}{+-}1{r_brace}=RP{sup 3} is known as the Euclidean projective spaces [Toth G. Glimpses of algebra and geometry. Springer-Verlag; 1998]. This relation was generalized to the semi-Euclidean projective space and then, the expression SO(3,1){approx_equal}S(3,2)/{l_brace}{+-}1{r_brace}=RP{sub 2}{sup 3} was acquired. Thus, it was found that Hopf fibriation map of S(2,1) can be used for Twistors (in not-null state) in quantum mechanics applications. In addition, the octonions and the split-octonions can be obtained from the Cayley-Dickson construction by defining a multiplication on pairs of quaternions or split quaternions. The automorphism group of the octonions is an exceptional Lie group. The split-octonions are used in the description of physical law. For example, the Dirac equation in physics (the equation of motion of a free spin 1/2 particle, like e.g. an electron or a proton) can be represented by a native split-octonion arithmetic.

  11. Split supersymmetry in brane models

    Indian Academy of Sciences (India)

    Type-I string theory in the presence of internal magnetic fields provides a concrete realization of split supersymmetry. To lowest order, gauginos are massless while squarks and sleptons are superheavy. For weak magnetic fields, the correct Standard Model spectrum guarantees gauge coupling unification with sin2 W ...

  12. VBSCan Split 2017 Workshop Summary

    Energy Technology Data Exchange (ETDEWEB)

    Anders, Christoph Falk; et al.

    2018-01-12

    This document summarises the talks and discussions happened during the VBSCan Split17 workshop, the first general meeting of the VBSCan COST Action network. This collaboration is aiming at a consistent and coordinated study of vector-boson scattering from the phenomenological and experimental point of view, for the best exploitation of the data that will be delivered by existing and future particle colliders.

  13. Split supersymmetry in brane models

    Indian Academy of Sciences (India)

    journal of. November 2006 physics pp. 793–802. Split supersymmetry in brane models. IGNATIOS ANTONIADIS∗. Department of Physics, CERN-Theory Division, 1211 Geneva 23, Switzerland. E-mail: Ignatios. ... that LEP data favor the unification of the three SM gauge couplings are smoking guns for the presence of new ...

  14. Water splitting by cooperative catalysis

    NARCIS (Netherlands)

    Hetterscheid, D.G.H.; van der Vlugt, J.I.; de Bruin, B.; Reek, J.N.H.

    2009-01-01

    A mononuclear Ru complex is shown to efficiently split water into H2 and O2 in consecutive steps through a heat- and light-driven process (see picture). Thermally driven H2 formation involves the aid of a non-innocent ligand scaffold, while dioxygen is generated by initial photochemically induced

  15. On split Lie triple systems

    Indian Academy of Sciences (India)

    Lie triple system; system of roots; root space; split Lie algebra; structure theory. 1. Introduction and previous definitions. Throughout this paper, Lie triple systems T are considered of arbitrary dimension and over an arbitrary field K. It is worth to mention that, unless otherwise stated, there is not any restriction on dim Tα or {k ...

  16. On split Lie triple systems

    Indian Academy of Sciences (India)

    The key tool in this job is the notion of connection of roots in the framework of split Lie triple systems. Author Affiliations. Antonio J Calderón Martín1. Departamento de Matemáticas, Universidad de Cádiz, 11510 Puerto Real, Cádiz, Spain. Dates. Manuscript received: 25 January 2008. Proceedings – Mathematical Sciences.

  17. Stability of split Stirling refrigerators

    International Nuclear Information System (INIS)

    Waele, A T A M de; Liang, W

    2009-01-01

    In many thermal systems spontaneous mechanical oscillations are generated under the influence of large temperature gradients. Well-known examples are Taconis oscillations in liquid-helium cryostats and oscillations in thermoacoustic systems. In split Stirling refrigerators the compressor and the cold finger are connected by a flexible tube. The displacer in the cold head is suspended by a spring. Its motion is pneumatically driven by the pressure oscillations generated by the compressor. In this paper we give the basic dynamic equations of split Stirling refrigerators and investigate the possibility of spontaneous mechanical oscillations if a large temperature gradient develops in the cold finger, e.g. during or after cool down. These oscillations would be superimposed on the pressure oscillations of the compressor and could ruin the cooler performance.

  18. 7 CFR 51.2002 - Split shell.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Split shell. 51.2002 Section 51.2002 Agriculture... Standards for Grades of Filberts in the Shell 1 Definitions § 51.2002 Split shell. Split shell means a shell... of the shell, measured in the direction of the crack. ...

  19. Origin and Propagation of Splits in High-Strength Low-Alloy Strip Steel

    Science.gov (United States)

    Punch, Rachel; Strangwood, Martin; Davis, Claire

    2012-12-01

    A high-strength strip steel (yield strength of ~700 MPa) with a ductile-brittle transition over a wide temperature range shows splits (fissures) on the fracture surfaces in the upper transition region. The steel, hot rolled to strip thicknesses of approximately 10.0 mm and 16.8 mm, had a predominantly fine-grained ferrite microstructure with some coarse grain patches (area percent of 11 pct and 42 pct, respectively). Low-blow Charpy tests were carried out at room temperature, corresponding to the upper transition region for these strips. The low-blow tests resulted in the formation of splits without main crack propagation from the notch; therefore, the energies at which the splits initiated could be determined. Acoustic emission (AE) sensors were used during low-blow Charpy testing of the strip steels and mild steel (where no splits occur); it was found that AE was able to detect signals from the hammer impact, split formation, and ductile deformation. Optical microscopy, scanning electron microscopy (SEM), and X-ray tomography were carried out, which verified the presence of splits and showed that they propagated by transgranular cleavage, preferentially following coarse-grained regions. No significant difference in the number or length of splits between the 10- and 16.8-mm strip was observed, but the 10-mm strip did produce deeper splits during the low-blow Charpy testing. The deeper splits contribute to a lower impact transition temperature for the 10-mm strip material.

  20. Copper diffusion in In2S3 and charge separation at In2S3/CuSCN and TiO2/In2S3 interfaces

    International Nuclear Information System (INIS)

    Juma, Albert Owino

    2013-01-01

    The concept of inorganic nanostructured solar cells consists of a very thin absorber layer sandwiched between highly structured electron and hole conductors. When a TiO 2 /In 2 S 3 /CuSCN nanocomposite heterostructure is illuminated with light, photo-generated electrons in In 2 S 3 can be injected into the conduction band of TiO 2 and holes into the valence band of CuSCN. Charge transfer at the interfaces is limited by the deposition parameters, band alignment and diffusion of Cu from CuSCN into In 2 S 3 , which was the focus of this work. TiO 2 nanoparticles were screen printed onto SnO 2 :F (FTO)-coated glass substrates to give a layer of nanoporous (np) TiO 2 . In 2 S 3 layers were deposited by thermal evaporation or ion layer gas reaction (ILGAR) methods producing Cl-free (In(acac) 3 precursor) and Cl-containing (InCl 3 precursor) layers. A spray-spin method was developed for deposition of CuSCN onto In 2 S 3 . Diffusion of Cu into In 2 S 3 layers was investigated by Rutherford backscattering spectrometry (RBS) while charge transport mechanisms were studied with surface photovoltage (SPV) technique in the fixed capacitor configuration. The activation energy (Ea) for Cu diffusion in thermally evaporated and Cl-free ILGAR In 2 S 3 layers was 0.30 and 0.24 eV, respectively but increased to between 0.72 and 0.78 eV for Cl-containing In 2 S 3 with residual Cl concentrations of 7.8 - 13.8 at.%. The diffusion prefactor (D 0 ) was six orders of magnitude higher for Cl-containing compared to Cl-free layers. The relationship between E a and D 0 was described by the Meyer-Neldel rule with a Meyer-Neldel energy of 40 meV. The presence of Cl has no significant influence on the structural properties of In 2 S 3 but resulted in a modified diffusion mechanism for Cu diffusion. The photovoltage of In 2 S 3 /CuSCN samples decreased after annealing for longer than 2 min at 200 C. A defect band was formed near the interface where holes accumulated and electrons tunneled through

  1. Fabrication of In2O3@In2S3 core-shell nanocubes for enhanced photoelectrochemical performance

    Science.gov (United States)

    Li, Haohua; Chen, Cong; Huang, Xinyou; Leng, Yang; Hou, Mengnan; Xiao, Xiaogu; Bao, Jie; You, Jiali; Zhang, Wenwen; Wang, Yukun; Song, Juan; Wang, Yaping; Liu, Qinqin; Hope, Gregory A.

    2014-02-01

    Herein, we report the facile synthesis of In2O3@In2S3 core-shell nanocubes and their improved photoelectrochemical property. In2O3@In2S3 core-shell nanocubes are grown on a F-doped SnO2 (FTO) glass substrate by a two-step process, which involves the electrodeposition of In2O3 nanocubes and a subsequent ion-exchange treatment. The improved light-harvesting ability and the suitable band alignment of the In2O3@In2S3 core-shell nanocubes generate a remarkable photocurrent density of 6.19 mA cm-2 (at 0 V vs. Ag/AgCl), which is substantially higher than the pristine In2O3 nanocubes. These results provide a new insight into the design of a high-performance photoanode for photoelectrochemical water splitting.

  2. Innovative wedge axe in making split firewood

    International Nuclear Information System (INIS)

    Mutikainen, A.

    1998-01-01

    Interteam Oy, a company located in Espoo, has developed a new method for making split firewood. The tools on which the patented System Logmatic are based are wedge axe and cylindrical splitting-carrying frame. The equipment costs about 495 FIM. The block of wood to be split is placed inside the upright carrying frame and split in a series of splitting actions using the innovative wedge axe. The finished split firewood remains in the carrying frame, which (as its name indicates) also serves as the means for carrying the firewood. This innovative wedge-axe method was compared with the conventional splitting of wood using an axe (Fiskars -handy 1400 splitting axe costing about 200 FIM) in a study conducted at TTS-Institute. There were eight test subjects involved in the study. In the case of the wedge-axe method, handling of the blocks to be split and of the finished firewood was a little quicker, but in actual splitting it was a little slower than the conventional axe method. The average productivity of splitting the wood and of the work stages related to it was about 0.4 m 3 per effective hour in both methods. The methods were also equivalent of one another in terms of the load imposed by the work when measured in terms of the heart rate. As regards work safety, the wedge-axe method was superior to the conventional method, but the continuous striking action and jolting transmitted to the arms were unpleasant (orig.)

  3. CONDUCTION MECHANISM IN AMORPHOUS As2S3

    African Journals Online (AJOL)

    User

    port measurements in disordered semiconduc- tors and .... 2, with T0 = Eg/2. Eg is the mobility gap and has the same value (2.15 Ev) over the whole measured temperature range. This indicates that the conduction in amorphous As2S3 is intrinsic ... 2 : lnρ as a function of reciprocal temperature for amorphous As2S3. 15. 17.

  4. Preparation and characterization of Bi 2 S 3 compound semiconductor

    Indian Academy of Sciences (India)

    ... are grown by layer by layer mechanism.We studied the transport properties viz. Hall effect, resistivity, thermoelectric power and thermal conductivity on Bi2S3 pellets. Raman spectroscopy and thermal gravimetric analysis (TGA) were carried out on Bi2S3 single crystal for studying their optical and thermal behaviours.

  5. German S3-Guideline: Rectovaginal fistula [Deutsche S3-Leitlinie: Rektovaginale Fistel

    Directory of Open Access Journals (Sweden)

    Ommer, Andreas

    2012-10-01

    Full Text Available [english] Background: Rectovaginal fistulas are rare, and the majority is of traumatic origin. The most common causes are obstetric trauma, local infection, and rectal surgery. This guideline does not cover rectovaginal fistulas that are caused by chronic inflammatory bowel disease.Methods: A systematic review of the literature was undertaken. Results: Rectovaginal fistula is diagnosed on the basis of the patient history and the clinical examination. Other pathologies should be ruled out by endoscopy, endosonography or tomography. The assessment of sphincter function is valuable for surgical planning (potential simultaneous sphincter reconstruction.Persistent rectovaginal fistulas generally require surgical treatment. Various surgical procedures have been described. The most common procedure involves a transrectal approach with endorectal suture. The transperineal approach is primarily used in case of simultaneous sphincter reconstruction. In recurrent fistulas. Closure can be achieved by the interposition of autologous tissue (Martius flap, gracilis muscle or biologically degradable materials. In higher fistulas, abdominal approaches are used as well. Stoma creation is more frequently required in rectovaginal fistulas than in anal fistulas. The decision regarding stoma creation should be primarily based on the extent of the local defect and the resulting burden on the patient.Conclusion: In this clinical S3-Guideline, instructions for diagnosis and treatment of rectovaginal fistulas are described for the first time in Germany. Given the low evidence level, this guideline is to be considered of descriptive character only. Recommendations for diagnostics and treatment are primarily based the clinical experience of the guideline group and cannot be fully supported by the literature.[german] Hintergrund: Rektovaginale Fisteln stellen eine seltene Erkrankung dar. Die Mehrzahl der rektovaginalen Fisteln ist traumatischer Genese. Die wichtigsten

  6. Detection of the Third Heart Sound Based on Nonlinear Signal Decomposition and Time-Frequency Localization.

    Science.gov (United States)

    Barma, Shovan; Chen, Bo-Wei; Ji, Wen; Rho, Seungmin; Chou, Chih-Hung; Wang, Jhing-Fa

    2016-08-01

    This study presents a precise way to detect the third ( S3 ) heart sound, which is recognized as an important indication of heart failure, based on nonlinear single decomposition and time-frequency localization. The detection of the S3 is obscured due to its significantly low energy and frequency. Even more, the detected S3 may be misunderstood as an abnormal second heart sound with a fixed split, which was not addressed in the literature. To detect such S3, the Hilbert vibration decomposition method is applied to decompose the heart sound into a certain number of subcomponents while intactly preserving the phase information. Thus, the time information of all of the decomposed components are unchanged, which further expedites the identification and localization of any module/section of a signal properly. Next, the proposed localization step is applied to the decomposed subcomponents by using smoothed pseudo Wigner-Ville distribution followed by the reassignment method. Finally, based on the positional information, the S3 is distinguished and confirmed by measuring time delays between the S2 and S3. In total, 82 sets of cardiac cycles collected from different databases including Texas Heart Institute database are examined for evaluation of the proposed method. The result analysis shows that the proposed method can detect the S3 correctly, even when the normalized temporal energy of S3 is larger than 0.16, and the frequency of those is larger than 34 Hz. In a performance analysis, the proposed method demonstrates that the accuracy rate of S3 detection is as high as 93.9%, which is significantly higher compared with the other methods. Such findings prove the robustness of the proposed idea for detecting substantially low-energized S3 .

  7. Parallel BLAST on split databases.

    Science.gov (United States)

    Mathog, David R

    2003-09-22

    BLAST programs often run on large SMP machines where multiple threads can work simultaneously and there is enough memory to cache the databases between program runs. A group of programs is described which allows comparable performance to be achieved with a Beowulf configuration in which no node has enough memory to cache a database but the cluster as an aggregate does. To achieve this result, databases are split into equal sized pieces and stored locally on each node. Each query is run on all nodes in parallel and the resultant BLAST output files from all nodes merged to yield the final output. Source code is available from ftp://saf.bio.caltech.edu/

  8. Split Dirac Supersymmetry: An Ultraviolet Completion of Higgsino Dark Matter

    Energy Technology Data Exchange (ETDEWEB)

    Fox, Patrick J. [Fermilab; Kribs, Graham D. [Oregon U.; Martin, Adam [Notre Dame U.

    2014-10-07

    Motivated by the observation that the Higgs quartic coupling runs to zero at an intermediate scale, we propose a new framework for models of split supersymmetry, in which gauginos acquire intermediate scale Dirac masses of $\\sim 10^{8-11}$ GeV. Scalar masses arise from one-loop finite contributions as well as direct gravity-mediated contributions. Like split supersymmetry, one Higgs doublet is fine-tuned to be light. The scale at which the Dirac gauginos are introduced to make the Higgs quartic zero is the same as is necessary for gauge coupling unification. Thus, gauge coupling unification persists (nontrivially, due to adjoint multiplets), though with a somewhat higher unification scale $\\gtrsim 10^{17}$ GeV. The $\\mu$-term is naturally at the weak scale, and provides an opportunity for experimental verification. We present two manifestations of Split Dirac Supersymmetry. In the "Pure Dirac" model, the lightest Higgsino must decay through R-parity violating couplings, leading to an array of interesting signals in colliders. In the "Hypercharge Impure" model, the bino acquires a Majorana mass that is one-loop suppressed compared with the Dirac gluino and wino. This leads to weak scale Higgsino dark matter whose overall mass scale, as well as the mass splitting between the neutral components, is naturally generated from the same UV dynamics. We outline the challenges to discovering pseudo-Dirac Higgsino dark matter in collider and dark matter detection experiments.

  9. Iterative group splitting algorithm for opportunistic scheduling systems

    KAUST Repository

    Nam, Haewoon

    2014-05-01

    An efficient feedback algorithm for opportunistic scheduling systems based on iterative group splitting is proposed in this paper. Similar to the opportunistic splitting algorithm, the proposed algorithm adjusts (or lowers) the feedback threshold during a guard period if no user sends a feedback. However, when a feedback collision occurs at any point of time, the proposed algorithm no longer updates the threshold but narrows down the user search space by dividing the users into multiple groups iteratively, whereas the opportunistic splitting algorithm keeps adjusting the threshold until a single user is found. Since the threshold is only updated when no user sends a feedback, it is shown that the proposed algorithm significantly alleviates the signaling overhead for the threshold distribution to the users by the scheduler. More importantly, the proposed algorithm requires a less number of mini-slots than the opportunistic splitting algorithm to make a user selection with a given level of scheduling outage probability or provides a higher ergodic capacity given a certain number of mini-slots. © 2013 IEEE.

  10. Optical properties study in 0.3 La2 S3-0.7 Ga2 S3

    International Nuclear Information System (INIS)

    Marmolejo, Edgar M.; Paula, Ana M. de; Reynoso, V.C.S.; Barbosa, Luiz C.; Alves, Oswaldo L.

    1998-01-01

    Optical properties study in 0.3 La 2 S 3 -0.7 Ga 2 S 3 . In this work we describe the synthesis and characterization of chalcogenide glass (0.3 La 2 S 3 -0.7 Ga 2 S 3 ) with low phonons frequencies. Several properties were measured like Sellmeier parameters, linear refractive index dispersion and material dispersion. Samples with the composition above were doped with Dy 2 S 3 . The absorption and emission characteristics were measured by electronic spectroscopy and fluorescence spectrum respectively. Raman and infrared spectroscopy shows that these glasses present low phonons frequencies and structure composed by GaS 4 tetrahedral. The Lines model was used for calculate the coefficients values of the non linear refractive index. (author)

  11. Stringy N = (2, 2) holography for AdS3

    Science.gov (United States)

    Datta, Shouvik; Eberhardt, Lorenz; Gaberdiel, Matthias R.

    2018-01-01

    We propose a class of AdS3/CFT2 dualities with N = (2, 2) supersymmetry. These dualities relate string theory on {AdS}_3× ({S}^3× T^4)/G to marginal deformations of the symmetric product orbifold of T^4/G , where G is a dihedral group. We demonstrate that the BPS spectrum calculated from supergravity and string theory agrees with that of the dual CFT. Moreover, the supergravity elliptic genus is shown to reproduce the CFT answer, thus providing further non-trivial evidence in favour of the proposal.

  12. Reinnervated Split-Muscle Technique for Creating Additional Myoelectric Sites in an Animal Model.

    Science.gov (United States)

    Deslivia, Maria Florencia; Lee, Hyun-Joo; Zulkarnain, Rizki Fajar; Zhu, Bin; Adikrishna, Arnold; Jeon, In-Ho; Kim, Keehoon

    2016-12-01

    This study proposes a novel reinnervated split-muscle operation to create additional myoelectric sites as sources of command signals of myoelectric prostheses for enhanced dexterous hand-to-wrist motions. The aim of this study was to investigate the postprocedure electromyographic properties of the muscles as distinct myoelectric sites in a rat model. The reinnervated split-muscle group (n = 6) had the gastrocnemius muscle separated along its longitudinal axis and nerves transferred to each new muscle (peroneal nerve to lateral muscle head and tibial to medial one); the non-split-muscle group (n = 6) only had nerve transfers with its muscle intact. Functional testing was conducted after 10 weeks. The main parameter is the difference in mean electromyographic amplitude between the new muscles, with greater values indicating better separability. After the reinnervated split-muscle procedure, there is a significant increase of the average ratio between two muscles compared with the control group, from 0.44 (range, 0.02 to 0.86) to 0.77 (range, 0.35 to 0.98) (p = 0.011). In addition, compared with the non-split muscle group, nerve transfer in the split-muscle group is more successful in reaching its intended target muscle. A reinnervated split-muscle procedure could be beneficial for acquiring a more precise and discrete command signal in upper limb amputees, thus enabling the creation of more dexterous prosthetic arm.

  13. Algebraic techniques for diagonalization of a split quaternion matrix in split quaternionic mechanics

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Tongsong, E-mail: jiangtongsong@sina.com [Department of Mathematics, Linyi University, Linyi, Shandong 276005 (China); Department of Mathematics, Heze University, Heze, Shandong 274015 (China); Jiang, Ziwu; Zhang, Zhaozhong [Department of Mathematics, Linyi University, Linyi, Shandong 276005 (China)

    2015-08-15

    In the study of the relation between complexified classical and non-Hermitian quantum mechanics, physicists found that there are links to quaternionic and split quaternionic mechanics, and this leads to the possibility of employing algebraic techniques of split quaternions to tackle some problems in complexified classical and quantum mechanics. This paper, by means of real representation of a split quaternion matrix, studies the problem of diagonalization of a split quaternion matrix and gives algebraic techniques for diagonalization of split quaternion matrices in split quaternionic mechanics.

  14. Globally regular instability of AdS_3

    OpenAIRE

    Bizon, P.; Jałmużna, J.

    2013-01-01

    We consider three-dimensional AdS gravity minimally coupled to a massless scalar field and study numerically the evolution of small smooth circularly symmetric perturbations of the $AdS_3$ spacetime. As in higher dimensions, for a large class of perturbations, we observe a turbulent cascade of energy to high frequencies which entails instability of $AdS_3$. However, in contrast to higher dimensions, the cascade cannot be terminated by black hole formation because small perturbations have ener...

  15. Testing PVLAS axions with resonant photon splitting

    CERN Document Server

    Gabrielli, E; Gabrielli, Emidio; Giovannini, Massimo

    2007-01-01

    The photon splitting gamma -> gamma gamma in a time-independent and inhomogeneous magnetized background is considered when neutral and ultralight spin-0 particles are coupled to two-photons. Depending on the inhomogeneity scale of the external field, resonant photon splitting can occur. If an optical laser crosses a magnetic field of few Tesla with typical inhomogeneity scale of the order of the meter, a potentially observable rate of photon splittings is expected for the PVLAS range of couplings and masses.

  16. Additive operator-difference schemes splitting schemes

    CERN Document Server

    Vabishchevich, Petr N

    2013-01-01

    Applied mathematical modeling isconcerned with solving unsteady problems. This bookshows how toconstruct additive difference schemes to solve approximately unsteady multi-dimensional problems for PDEs. Two classes of schemes are highlighted: methods of splitting with respect to spatial variables (alternating direction methods) and schemes of splitting into physical processes. Also regionally additive schemes (domain decomposition methods)and unconditionally stable additive schemes of multi-component splitting are considered for evolutionary equations of first and second order as well as for sy

  17. Iterative Splitting Methods for Differential Equations

    CERN Document Server

    Geiser, Juergen

    2011-01-01

    Iterative Splitting Methods for Differential Equations explains how to solve evolution equations via novel iterative-based splitting methods that efficiently use computational and memory resources. It focuses on systems of parabolic and hyperbolic equations, including convection-diffusion-reaction equations, heat equations, and wave equations. In the theoretical part of the book, the author discusses the main theorems and results of the stability and consistency analysis for ordinary differential equations. He then presents extensions of the iterative splitting methods to partial differential

  18. Spin Splitting in Different Semiconductor Quantum Wells

    International Nuclear Information System (INIS)

    Hao Yafei

    2012-01-01

    We theoretically investigate the spin splitting in four undoped asymmetric quantum wells in the absence of external electric field and magnetic field. The quantum well geometry dependence of spin splitting is studied with the Rashba and the Dresselhaus spin-orbit coupling included. The results show that the structure of quantum well plays an important role in spin splitting. The Rashba and the Dresselhaus spin splitting in four asymmetric quantum wells are quite different. The origin of the distinction is discussed in this work. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

  19. Dark matter from split seesaw

    International Nuclear Information System (INIS)

    Kusenko, Alexander; Takahashi, Fuminobu; Yanagida, Tsutomu T.

    2010-01-01

    The seesaw mechanism in models with extra dimensions is shown to be generically consistent with a broad range of Majorana masses. The resulting democracy of scales implies that the seesaw mechanism can naturally explain the smallness of neutrino masses for an arbitrarily small right-handed neutrino mass. If the scales of the seesaw parameters are split, with two right-handed neutrinos at a high scale and one at a keV scale, one can explain the matter-antimatter asymmetry of the universe, as well as dark matter. The dark matter candidate, a sterile right-handed neutrino with mass of several keV, can account for the observed pulsar velocities and for the recent data from Chandra X-ray Observatory, which suggest the existence of a 5 keV sterile right-handed neutrino.

  20. Emittance compensation in split photoinjectors

    Directory of Open Access Journals (Sweden)

    Klaus Floettmann

    2017-01-01

    Full Text Available The compensation of correlated emittance contributions is of primary importance to optimize the performance of high brightness photoinjectors. While only extended numerical simulations can capture the complex beam dynamics of space-charge-dominated beams in sufficient detail to optimize a specific injector layout, simplified models are required to gain a deeper understanding of the involved dynamics, to guide the optimization procedure, and to interpret experimental results. In this paper, a slice envelope model for the emittance compensation process in a split photoinjector is presented. The emittance term is included in the analytical solution of the beam envelope in a drift, which is essential to take the emittance contribution due to a beam size mismatch into account. The appearance of two emittance minima in the drift is explained, and the matching into the booster cavity is discussed. A comparison with simulation results points out effects which are not treated in the envelope model, such as overfocusing and field nonlinearities.

  1. Gauge mediated mini-split

    Science.gov (United States)

    Cohen, Timothy; Craig, Nathaniel; Knapen, Simon

    2016-03-01

    We propose a simple model of split supersymmetry from gauge mediation. This model features gauginos that are parametrically a loop factor lighter than scalars, accommodates a Higgs boson mass of 125 GeV, and incorporates a simple solution to the μ- b μ problem. The gaugino mass suppression can be understood as resulting from collective symmetry breaking. Imposing collider bounds on μ and requiring viable electroweak symmetry breaking implies small a-terms and small tan β — the stop mass ranges from 105 to 108 GeV. In contrast with models with anomaly + gravity mediation (which also predict a one-loop loop suppression for gaugino masses), our gauge mediated scenario predicts aligned squark masses and a gravitino LSP. Gluinos, electroweakinos and Higgsinos can be accessible at the LHC and/or future colliders for a wide region of the allowed parameter space.

  2. Minimal Doubling and Point Splitting

    Energy Technology Data Exchange (ETDEWEB)

    Creutz, M.

    2010-06-14

    Minimally-doubled chiral fermions have the unusual property of a single local field creating two fermionic species. Spreading the field over hypercubes allows construction of combinations that isolate specific modes. Combining these fields into bilinears produces meson fields of specific quantum numbers. Minimally-doubled fermion actions present the possibility of fast simulations while maintaining one exact chiral symmetry. They do, however, introduce some peculiar aspects. An explicit breaking of hyper-cubic symmetry allows additional counter-terms to appear in the renormalization. While a single field creates two different species, spreading this field over nearby sites allows isolation of specific states and the construction of physical meson operators. Finally, lattice artifacts break isospin and give two of the three pseudoscalar mesons an additional contribution to their mass. Depending on the sign of this mass splitting, one can either have a traditional Goldstone pseudoscalar meson or a parity breaking Aoki-like phase.

  3. Gauge mediated mini-split

    Energy Technology Data Exchange (ETDEWEB)

    Cohen, Timothy [Institute of Theoretical Science, University of Oregon,Eugene, OR 97403 (United States); Craig, Nathaniel [Department of Physics, University of California,Santa Barbara, CA 93106 (United States); Knapen, Simon [Berkeley Center for Theoretical Physics,University of California, Berkeley, CA 94720 (United States); Theoretical Physics Group,Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States)

    2016-03-15

    We propose a simple model of split supersymmetry from gauge mediation. This model features gauginos that are parametrically a loop factor lighter than scalars, accommodates a Higgs boson mass of 125 GeV, and incorporates a simple solution to the μ−b{sub μ} problem. The gaugino mass suppression can be understood as resulting from collective symmetry breaking. Imposing collider bounds on μ and requiring viable electroweak symmetry breaking implies small a-terms and small tan β — the stop mass ranges from 10{sup 5} to 10{sup 8} GeV. In contrast with models with anomaly + gravity mediation (which also predict a one-loop loop suppression for gaugino masses), our gauge mediated scenario predicts aligned squark masses and a gravitino LSP. Gluinos, electroweakinos and Higgsinos can be accessible at the LHC and/or future colliders for a wide region of the allowed parameter space.

  4. Evaluation report on SCTF Core-III tests S3-14, S3-15 and S3-16

    International Nuclear Information System (INIS)

    Iwamura, Takamichi; Iguchi, Tadashi; Akimoto, Hajime; Okubo, Tsutomu; Ohnuki, Akira; Sakaki, Isao; Adachi, Hiromichi; Murao, Yoshio

    1988-03-01

    It was revealed from previous reflood tests using Slab Core Test Facility (SCTF) that the heat transfer was enhanced in high power bundles and degraded in low power bundles due to the radial power distribution. In the present study, the effects of local power ratio itself and the shape of radial power distribution were separately investigated by comparing three tests: S3-14 (flat power distribution), S3-15 (inclined power distribution) and S3-16 (steep power distribution). Those three tests were performed under the same boundary conditions, total power and initial stored energy. The emergency core cooling (ECC) water was injected into the lower plenum. The test results indicated that the heat transfer enhancement and degradation was governed mainly by the bundlewise radial power ratio and less dependent on the shape of radial power distribution when the difference in power ratios between adjacent bundles is less than 0.44. The degree of heat transfer enhancement at high power bundles was increased with the radial peak power ratio. Even at an average power bundle, the heat transfer was enhanced in the non-uniform radial power distribution tests. (author)

  5. SplitDist—Calculating Split-Distances for Sets of Trees

    DEFF Research Database (Denmark)

    Mailund, T

    2004-01-01

    We present a tool for comparing a set of input trees, calculating for each pair of trees the split-distances, i.e., the number of splits in one tree not present in the other.......We present a tool for comparing a set of input trees, calculating for each pair of trees the split-distances, i.e., the number of splits in one tree not present in the other....

  6. Synthesis and growth mechanism of Bi2S3 nanoribbons.

    Science.gov (United States)

    Liu, Zhaoping; Liang, Jianbo; Li, Shu; Peng, Sheng; Qian, Yitai

    2004-02-06

    This article describes a facile solvothermal method by using mixed solvents for the large-scale synthesis of Bi(2)S(3) nanoribbons with lengths of up to several millimeters. These nanoribbons were formed by a solvothermal reaction between Bi(III)-glycerol complexes and various sulfur sources in a mixed solution of aqueous NaOH and glycerol. HRTEM (high-resolution transmission electron microscopy) and SAED (selective-area electron diffraction) studies show that the as-synthesized nanoribbons had predominately grown along the [001] direction. The Bi(2)S(3) nanoribbons prepared by the use of different sulfur sources have a common formation process: the initial formation of NaBiS(2) polycrystals, which serve as the precursors to Bi(2)S(3), the decomposition of NaBiS(2), and the formation of Bi(2)S(3) seeds in the solution through a homogeneous nucleation process; the growth of Bi(2)S(3) nanoribbons occurs at the expense of NaBiS(2) materials. The growth mechanism of millimeter-scale nanoribbons involves a special solid-solution-solid transformation as well as an Ostwald ripening process. Some crucial factors affect nanoribbon growth, such as, solvothermal temperature, volume ratio of glycerol to water, and the concentration of NaOH; these have also been discussed.

  7. Split2 Protein-Ligation Generates Active IL-6-Type Hyper-Cytokines from Inactive Precursors.

    Science.gov (United States)

    Moll, Jens M; Wehmöller, Melanie; Frank, Nils C; Homey, Lisa; Baran, Paul; Garbers, Christoph; Lamertz, Larissa; Axelrod, Jonathan H; Galun, Eithan; Mootz, Henning D; Scheller, Jürgen

    2017-12-15

    Trans-signaling of the major pro- and anti-inflammatory cytokines Interleukin (IL)-6 and IL-11 has the unique feature to virtually activate all cells of the body and is critically involved in chronic inflammation and regeneration. Hyper-IL-6 and Hyper-IL-11 are single chain designer trans-signaling cytokines, in which the cytokine and soluble receptor units are trapped in one complex via a flexible peptide linker. Albeit, Hyper-cytokines are essential tools to study trans-signaling in vitro and in vivo, the superior potency of these designer cytokines are accompanied by undesirable stress responses. To enable tailor-made generation of Hyper-cytokines, we developed inactive split-cytokine-precursors adapted for posttranslational reassembly by split-intein mediated protein trans-splicing (PTS). We identified cutting sites within IL-6 (E 134 /S 135 ) and IL-11 (G 116 /S 117 ) and obtained inactive split-Hyper-IL-6 and split-Hyper-IL-11 cytokine precursors. After fusion with split-inteins, PTS resulted in reconstitution of active Hyper-cytokines, which were efficiently secreted from transfected cells. Our strategy comprises the development of a background-free cytokine signaling system from reversibly inactivated precursor cytokines.

  8. Split Questionnaire Design for Massive Surveys

    NARCIS (Netherlands)

    Adiguzel, F.; Wedel, M.

    2008-01-01

    Companies are conducting more and longer surveys than ever before. Massive questionnaires are pervasive in marketing practice. As an alternative to the heuristic methods that are currently used to split questionnaires, this study develops a methodology to design the split questionnaire in a way that

  9. Cheating More when the Spoils Are Split

    Science.gov (United States)

    Wiltermuth, Scott S.

    2011-01-01

    Four experiments demonstrated that people are more likely to cheat when the benefits of doing so are split with another person, even an anonymous stranger, than when the actor alone captures all of the benefits. In three of the studies, splitting the benefits of over-reporting one's performance on a task made such over-reporting seem less…

  10. Split Scheduling with Uniform Setup Times

    NARCIS (Netherlands)

    Schalekamp, F.; Sitters, R.A.; van der Ster, S.L.; Stougie, L.; Verdugo, V.; van Zuylen, A.

    2015-01-01

    We study a scheduling problem in which jobs may be split into parts, where the parts of a split job may be processed simultaneously on more than one machine. Each part of a job requires a setup time, however, on the machine where the job part is processed. During setup, a machine cannot process or

  11. Split scheduling with uniform setup times.

    NARCIS (Netherlands)

    F. Schalekamp; R.A. Sitters (René); S.L. van der Ster; L. Stougie (Leen); V. Verdugo; A. van Zuylen

    2015-01-01

    htmlabstractWe study a scheduling problem in which jobs may be split into parts, where the parts of a split job may be processed simultaneously on more than one machine. Each part of a job requires a setup time, however, on the machine where the job part is processed. During setup, a

  12. On split Lie triple systems II

    Indian Academy of Sciences (India)

    Lie triple system with a coherent 0-root space is the direct sum of the family of its minimal ideals, each one being a simple split Lie triple system, and the simplicity of T is characterized. In the present paper we extend these results to arbitrary split Lie triple systems with no restrictions on their 0-root spaces. Keywords.

  13. Photoexcited Carrier Dynamics of In2S3 Thin Films.

    Science.gov (United States)

    McCarthy, Robert F; Schaller, Richard D; Gosztola, David J; Wiederrecht, Gary P; Martinson, Alex B F

    2015-07-02

    Indium sulfide (In2S3) is a promising absorber base for substitutionally doped intermediate band photovoltaics (IBPV); however, the dynamics of charge carriers traversing the electronic density of states that determine the optical and electronic response of thin films under stimuli have yet to be explored. The kinetics of photophysical processes in In2S3 grown by oxygen-free atomic layer deposition are deduced from photoconductivity, photoluminescence (PL), and transient absorption spectroscopy. We develop a map of excited-state dynamics for polycrystalline thin films including a secondary conduction band ∼2.1 eV above the first, plus sulfur vacancy and indium interstitial defect levels resulting in long-lived (∼100 ns) transients. Band-edge recombination produces PL and stimulated emission, which both intensify and red-shift as deposition temperature and grain size increase. The effect of rapid conduction band electron relaxation (In2S3-based absorbers is finally considered.

  14. Particulate photocatalysts for overall water splitting

    Science.gov (United States)

    Chen, Shanshan; Takata, Tsuyoshi; Domen, Kazunari

    2017-10-01

    The conversion of solar energy to chemical energy is a promising way of generating renewable energy. Hydrogen production by means of water splitting over semiconductor photocatalysts is a simple, cost-effective approach to large-scale solar hydrogen synthesis. Since the discovery of the Honda-Fujishima effect, considerable progress has been made in this field, and numerous photocatalytic materials and water-splitting systems have been developed. In this Review, we summarize existing water-splitting systems based on particulate photocatalysts, focusing on the main components: light-harvesting semiconductors and co-catalysts. The essential design principles of the materials employed for overall water-splitting systems based on one-step and two-step photoexcitation are also discussed, concentrating on three elementary processes: photoabsorption, charge transfer and surface catalytic reactions. Finally, we outline challenges and potential advances associated with solar water splitting by particulate photocatalysts for future commercial applications.

  15. The pressure-induced phase transition studies of In2S3 and In2S3:Ce nanoparticles

    Science.gov (United States)

    Yao, Binbin; Zhu, Hongyang; Wang, Shuangming; Wang, Pan; Zhang, Mingzhe

    2014-02-01

    A novel method, gas-liquid phase chemical deposition is developed to prepare In2S3 and In2S3:Ce nanoparticles. The structural, morphology and composition feature of these two nanoparticles is studied by XRD, HRTEM, and XPS. In situ high-pressure synchrotron X-ray diffraction studies were carried out by using a diamond-anvil cell. The doping does not influence the tetragonal-to-cubic phase transition path while results in a lower phase transition pressure of In2S3:Ce nanoparticles (4.3 GPa) than that of In2S3 nanoparticles (7.1 GPa). The bulk moduli of tetragonal phases are B0=87.1±4.3 GPa and B0=55.6±4.1 GPa, respectively. The distinct high-pressure behaviors can be explained in term of the doped ions, causing lattice distortion and reducing structural stability of the In2S3 nanoparticles and further accelerating the phase transition.

  16. Atomic structure of As2S3-Ag chalcogenide glasses

    Science.gov (United States)

    Kaban, I.; Jóvári, P.; Wagner, T.; Frumar, M.; Stehlik, S.; Bartos, M.; Hoyer, W.; Beuneu, B.; Webb, M. A.

    2009-09-01

    (As0.4S0.6)100-xAgx glasses (x = 0, 4, 8, 12 at.%) have been studied with high-energy x-ray diffraction, neutron diffraction and extended x-ray absorption spectroscopy at As and Ag K-edges. The experimental data were modelled simultaneously with the reverse Monte Carlo simulation method. Analysis of the partial pair correlation functions and coordination numbers extracted from the model atomic configurations revealed that silver preferentially bonds to sulfur in the As2S3-Ag ternary glasses, which results in the formation of homoatomic As-As bonds. Upon the addition of Ag, a small proportion of Ag-As bonds (NAgAs≈0.3) are formed in all three ternary compositions, while the direct Ag-Ag bonds (NAgAg≈ 0.4) appear only in the glass with the highest Ag content (12 at.%). Similar to the g- As2S3 binary, the mean coordination number of arsenic is close to three, and that of sulfur is close to two, in the As2S3-Ag ternary glasses. The first sharp diffraction peak on the total structure factors of As2S3 binary and (As0.4S0.6)100-xAgx ternary glasses is related to the As-As and As-S correlations.

  17. Model food standards regulation. S3. Irradiation of food

    International Nuclear Information System (INIS)

    1987-01-01

    This revised Model Food Standards Regulation S3 for the irradiation of food replaces the regulation adopted in June 1982. It specifies the types of ionizing radiations which may be used, lists the foods which may be processed and describes the requirements for an approved facility. It lists the records which are required to be kept and requirements for labelling of irradiated food

  18. Modeling of the Section Capacitance to Interface with a S3R

    Directory of Open Access Journals (Sweden)

    Fernández A.

    2017-01-01

    Full Text Available Cell capacitance is a well-known parameter in silicon solar cells. Its effects on the power units, specially on the S3R, is also well known since it has to be taken into account to design them. The capacitor energy is dis-charged into the power switch and the dissipation in-creases. Moreover, it introduces a delay in the energy transfer from the array to the main power bus. In triple junction solar cells, this parasitic element becomes far more complex and is not so well characterized. This paper addresses this issue and proposes a large signal model to be used in combination with a S3R.

  19. Energy level splitting and luminescence enhancement in AlN:Er by an external magnetic field

    Science.gov (United States)

    Maqbool, Muhammad; Ahmad, Iftikhar; Ali, Ghafar; Maaz, Khan

    2015-08-01

    Sputter deposited thin film AlN:Er (1 at.%) emits at 554 nm and 561 nm as a result of 2H11/2→ 4I15/2 and 4S3/2→ 4I15/2 transitions under 532 nm NdYAG laser and 783.3 nm crystal laser excitation. An external magnetic field of 0.1 T enhances the green emission and splits the 4S3/2 energy level in two sub-levels with a difference of 0.013 eV. The splitting of energy level produces new emission from Er3+ with a wavelength of 564.5 nm. Infrared emission is also observed at 1552 nm as a result of 4I13/2→ 4I15/2 transition. Enhanced luminescence shows the suitability of Er3+ for high efficiency optical devices.

  20. Split-coil-system SULTAN

    International Nuclear Information System (INIS)

    Vecsey, G.

    1992-08-01

    The high field superconductor test facility SULTAN started operation successfully in May 1992. Originally designed for testing full scale conductors for the large magnets of the next generation fusion reactors, the SULTAN facility installed at PSI (Switzerland) was designed as a common venture of three European Laboratories: ENEA (Italy), ECN (Netherlands) and PSI, and built by ENEA and PSI in the framework of the Euratom Fusion Technology Program. Presently the largest facility in the world, with its superconducting split coil system generating 11 Tesla in a 0.6 m bore, it is ready now for testing superconductor samples with currents up to 50 kA at variable cooling conditions. Similar tests can be arranged also for other applications. SULTAN is offered by the European Community as a contribution to the worldwide cooperation for the next step of fusion reactor development ITER. First measurements on conductor developed by CEA (Cadarache) are now in progress. Others like those of ENEA and CERN will follow. For 1993, a test of an Italian 12 TZ model coil for fusion application is planned. SULTAN is a worldwide unique facility marking the competitive presence of Swiss technology in the field of applied superconductivity research. Based on development and design of PSI, the high field Nb 3 Sn superconductors and coils were fabricated at the works of Kabelwerke Brugg and ABB, numerous Swiss companies contributed to the success of this international effort. Financing of the Swiss contribution of SULTAN was made available by NEFF, BEW, BBW, PSI and EURATOM. (author) figs., tabs., 20 refs

  1. 2-Photon tandem device for water splitting

    DEFF Research Database (Denmark)

    Seger, Brian; Castelli, Ivano Eligio; Vesborg, Peter Christian Kjærgaard

    2014-01-01

    Within the field Of photocatalytic water splitting there are several strategies to achieve the goal of efficient and cheap photocatalytic water splitting. This work examines one particular strategy by focusing on monolithically stacked, two-photon photoelectrochemical cells. The overall aim...... absorption, this is the more difficult side to optimize. Nevertheless, by using TiO2 as a transparent cathode protection layer in conjunction with known H-2 evolution catalysts, protection is clearly feasible for a large bandgap photocathode. This suggests that there may be promising strategies...... for photocatalytic water splitting by using a large bandgap photocathode and a low bandgap photoanode with attached protection layers....

  2. Communication: Tunnelling splitting in the phosphine molecule

    Energy Technology Data Exchange (ETDEWEB)

    Sousa-Silva, Clara; Tennyson, Jonathan; Yurchenko, Sergey N. [Department of Physics and Astronomy, University College London, London WC1E 6BT (United Kingdom)

    2016-09-07

    Splitting due to tunnelling via the potential energy barrier has played a significant role in the study of molecular spectra since the early days of spectroscopy. The observation of the ammonia doublet led to attempts to find a phosphine analogous, but these have so far failed due to its considerably higher barrier. Full dimensional, variational nuclear motion calculations are used to predict splittings as a function of excitation energy. Simulated spectra suggest that such splittings should be observable in the near infrared via overtones of the ν{sub 2} bending mode starting with 4ν{sub 2}.

  3. Splitting Functions at High Transverse Momentum

    CERN Document Server

    Moutafis, Rhea Penelope; CERN. Geneva. TH Department

    2017-01-01

    Among the production channels of the Higgs boson one contribution could become significant at high transverse momentum which is the radiation of a Higgs boson from another particle. This note focuses on the calculation of splitting functions and cross sections of such processes. The calculation is first carried out on the example $e\\rightarrow e\\gamma$ to illustrate the way splitting functions are calculated. Then the splitting function of $e\\rightarrow eh$ is calculated in similar fashion. This procedure can easily be generalized to processes such as $q\\rightarrow qh$ or $g\\rightarrow gh$.

  4. Optical Properties of In2S3 Thin Films

    Science.gov (United States)

    Bodnar, I. V.; Polubok, V. A.

    2014-11-01

    Laser deposition on substrates at temperatures of 480, 610, and 720 K has been used to produce films of the compound In2S3. Single crystals of this compound grown by the Bridgeman-Stockbarger method are used as targets. The composition is determined by x-ray spectral analysis and the structure of the resulting crystals and films is determined by x-ray methods. Both the crystals and the films crystallize into a tetragonal spinel structure. Transmission spectra in the region of the intrinsic absorption edge are used to determine the width of the band gap and the refractive index of the In2S3 films. The band gap width is found to increase as the substrate temperature is raised.

  5. Optical and Thermal Properties of In2S3

    Directory of Open Access Journals (Sweden)

    Faycel Saadallah

    2011-01-01

    Full Text Available Photothermal deflection spectroscopy (PDS is carried out in order to investigate thermal and optical properties of Al doped In2S3. The influence of thermal annealing on its gap energy as well as its thermal properties is revealed. In this way, we notice that thermal conductivity is increased and the gap energy is reduced. These features are probably due to the improvement of the crystalline structure of the sample.

  6. Automatic detection of artifacts in converted S3D video

    Science.gov (United States)

    Bokov, Alexander; Vatolin, Dmitriy; Zachesov, Anton; Belous, Alexander; Erofeev, Mikhail

    2014-03-01

    In this paper we present algorithms for automatically detecting issues specific to converted S3D content. When a depth-image-based rendering approach produces a stereoscopic image, the quality of the result depends on both the depth maps and the warping algorithms. The most common problem with converted S3D video is edge-sharpness mismatch. This artifact may appear owing to depth-map blurriness at semitransparent edges: after warping, the object boundary becomes sharper in one view and blurrier in the other, yielding binocular rivalry. To detect this problem we estimate the disparity map, extract boundaries with noticeable differences, and analyze edge-sharpness correspondence between views. We pay additional attention to cases involving a complex background and large occlusions. Another problem is detection of scenes that lack depth volume: we present algorithms for detecting at scenes and scenes with at foreground objects. To identify these problems we analyze the features of the RGB image as well as uniform areas in the depth map. Testing of our algorithms involved examining 10 Blu-ray 3D releases with converted S3D content, including Clash of the Titans, The Avengers, and The Chronicles of Narnia: The Voyage of the Dawn Treader. The algorithms we present enable improved automatic quality assessment during the production stage.

  7. Optical and electronic properties of semiconducting Sn2S3

    Science.gov (United States)

    Singh, David J.

    2016-07-01

    We report the electronic and optical properties of Sn2S3 as obtained from first principles calculations with the modified Becke-Johnson potential. The electronic structure shows that Sn occurs in both divalent and tetravalent forms. The fundamental band gap of 0.82 eV is indirect. The direct gap is 0.97 eV, but the onset of strong optical absorption is much higher at ˜1.75 eV. This is as a consequence of the Sn2+ s and Sn4+ s characters of the valence and conduction band extrema, respectively. We also find strong and different anisotropies for conduction in p- and n-type Sn2S3. This should be taken into account in device structures in order to obtain efficient charge collection. The thermopowers are reasonably high for both p- and n-type materials. p-type Sn2S3 shows complex corrugated isosurface sections, while the n-type material shows multiple band extrema.

  8. Splitting Strip Detector Clusters in Dense Environments

    CERN Document Server

    Nachman, Benjamin Philip; The ATLAS collaboration

    2018-01-01

    Tracking in high density environments, particularly in high energy jets, plays an important role in many physics analyses at the LHC. In such environments, there is significant degradation of track reconstruction performance. Between runs 1 and 2, ATLAS implemented an algorithm that splits pixel clusters originating from multiple charged particles, using charge information, resulting in the recovery of much of the lost efficiency. However, no attempt was made in prior work to split merged clusters in the Semi Conductor Tracker (SCT), which does not measure charge information. In spite of the lack of charge information in SCT, a cluster-splitting algorithm has been developed in this work. It is based primarily on the difference between the observed cluster width and the expected cluster width, which is derived from track incidence angle. The performance of this algorithm is found to be competitive with the existing pixel cluster splitting based on track information.

  9. Structural basis of photosynthetic water-splitting

    International Nuclear Information System (INIS)

    Photosynthetic water-splitting takes place in photosystem II (PSII), a membrane protein complex consisting of 20 subunits with an overall molecular mass of 350 kDa. The light-induced water-splitting reaction catalyzed by PSII not only converts light energy into biologically useful chemical energy, but also provides us with oxygen indispensible for sustaining oxygenic life on the earth. We have solved the structure of PSII at a 1.9 Å resolution, from which, the detailed structure of the Mn 4 CaO 5 -cluster, the catalytic center for water-splitting, became clear. Based on the structure of PSII at the atomic resolution, possible mechanism of light-induced water-splitting was discussed

  10. Irrational beliefs, attitudes about competition, and splitting.

    Science.gov (United States)

    Watson, P J; Morris, R J; Miller, L

    2001-03-01

    Rational-Emotive Behavior Therapy (REBT) theoretically promotes actualization of both individualistic and social-oriented potentials. In a test of this assumption, the Belief Scale and subscales from the Survey of Personal Beliefs served as measures of what REBT presumes to be pathogenic irrationalities. These measures were correlated with the Hypercompetitive Attitude Scale (HCAS), the Personal Development Competitive Attitude Scale (PDCAS), factors from the Splitting Index, and self-esteem. Results for the HCAS and Self-Splitting supported the REBT claim about individualistic self-actualization. Mostly nonsignificant and a few counterintuitive linkages were observed for irrational beliefs with the PDCAS, Family-Splitting, and Other-Splitting, and these data suggested that REBT may be less successful in capturing the "rationality" of a social-oriented self-actualization. Copyright 2001 John Wiley & Sons, Inc.

  11. Mort Rainey's Split Personality in Secret Window

    OpenAIRE

    Sandjaya, Cynthya; Limanta, Liem Satya

    2013-01-01

    Psychological issue is the main issue discussed in David Koepp's Secret Window through its main character, Mort Rainey. Rainey's psychological struggle will be the main theme in this research. This thesis examines Rainey's split personality. Furthermore, in this study, we want to analyze the process of how Mort Rainey's personality splits into two different personalities. To meet the answer of this study, we will use the theory of Dissociative Identity Disorder with a support from Sigmund Fre...

  12. A split SUSY model from SUSY GUT

    OpenAIRE

    Wang, FeiDepartment of Physics and Engineering, Zhengzhou University, Zhengzhou, 450000, P.R. China; Wang, Wenyu(Institute of Theoretical Physics, College of Applied Science, Beijing University of Technology, Beijing, 100124, P.R. China); Yang, Jin(State Key Laboratory of Theoretical Physics, Institute of Theoretical Physics, Chinese Academy of Sciences, Beijing, 100190, P.R. China)

    2015-01-01

    We propose to split the sparticle spectrum from the hierarchy between the GUT scale and the Planck scale. A split supersymmetric model, which gives non-universal gaugino masses, is built with proper high dimensional operators in the framework of SO(10) GUT. Based on a calculation of two-loop beta functions for gauge couplings (taking into account all weak scale threshold corrections), we check the gauge coupling unification and dark matter constraints (relic density and direct detections). We...

  13. Split School of High Energy Physics 2015

    CERN Document Server

    2015-01-01

    Split School of High Energy Physics 2015 (SSHEP 2015) was held at the Faculty of Electrical Engineering, Mechanical Engineering and Naval Architecture (FESB), University of Split, from September 14 to September 18, 2015. SSHEP 2015 aimed at master and PhD students who were interested in topics pertaining to High Energy Physics. SSHEP 2015 is the sixth edition of the High Energy Physics School. Previous five editions were held at the Department of Physics, University of Sarajevo, Bosnia and Herzegovina.

  14. Are Ducted Mini-Splits Worth It?

    Energy Technology Data Exchange (ETDEWEB)

    Winkler, Jonathan M [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Maguire, Jeffrey B [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Metzger, Cheryn E. [Pacific Northwest National Laboratory; Zhang, Jason [Pacific Northwest National Laboratory

    2018-02-01

    Ducted mini-split heat pumps are gaining popularity in some regions of the country due to their energy-efficient specifications and their ability to be hidden from sight. Although product and install costs are typically higher than the ductless mini-split heat pumps, this technology is well worth the premium for some homeowners who do not like to see an indoor unit in their living area. Due to the interest in this technology by local utilities and homeowners, the Bonneville Power Administration (BPA) has funded the Pacific Northwest National Laboratory (PNNL) and the National Renewable Energy Laboratory (NREL) to develop capabilities within the Building Energy Optimization (BEopt) tool to model ducted mini-split heat pumps. After the fundamental capabilities were added, energy-use results could be compared to other technologies that were already in BEopt, such as zonal electric resistance heat, central air source heat pumps, and ductless mini-split heat pumps. Each of these technologies was then compared using five prototype configurations in three different BPA heating zones to determine how the ducted mini-split technology would perform under different scenarios. The result of this project was a set of EnergyPlus models representing the various prototype configurations in each climate zone. Overall, the ducted mini-split heat pumps saved about 33-60% compared to zonal electric resistance heat (with window AC systems modeled in the summer). The results also showed that the ducted mini-split systems used about 4% more energy than the ductless mini-split systems, which saved about 37-64% compared to electric zonal heat (depending on the prototype and climate).

  15. Antenna Splitting Functions for Massive Particles

    Energy Technology Data Exchange (ETDEWEB)

    Larkoski, Andrew J.; Peskin, Michael E.; /SLAC

    2011-06-22

    An antenna shower is a parton shower in which the basic move is a color-coherent 2 {yields} 3 parton splitting process. In this paper, we give compact forms for the spin-dependent antenna splitting functions involving massive partons of spin 0 and spin 1/2. We hope that this formalism we have presented will be useful in describing the QCD dynamics of the top quark and other heavy particles at LHC.

  16. Structural Dynamics of the Oxygen-Evolving Complex of Photosystem II in Water-Splitting Action.

    Science.gov (United States)

    Wilson, Andrew J; Jain, Prashant K

    2018-04-17

    Oxygenic photosynthesis in nature occurs via water splitting catalyzed by the oxygen-evolving complex (OEC) of photosystem II. To split water, the OEC cycles through a sequence of oxidation states (S i , i = 0-4), the structural mechanism of which is not fully understood under physiological conditions. We monitored the OEC in visible-light-driven water-splitting action by using in situ, aqueous-environment surface-enhanced Raman scattering (SERS). In the unexplored low-frequency region of SERS, we found dynamic vibrational signatures of water binding and splitting. Specific snapshots in the dynamic SERS correspond to intermediate states in the catalytic cycle, as determined by density functional theory and isotopologue comparisons. We assign the previously ambiguous protonation configuration of the S 0 -S 3 states and propose a structural mechanism of the OEC's catalytic cycle. The findings address unresolved questions about photosynthetic water splitting and introduce spatially resolved, low-frequency SERS as a chemically sensitive tool for interrogating homogeneous catalysis in operando.

  17. S3T working group. Report 1: group aims

    International Nuclear Information System (INIS)

    Pouey, M.

    1983-04-01

    The work group S3T which is aimed to designing and developing devices using unconventional holographic optics is presented. These devices find applications that are classified here in four items high resolution spectrometers, high definition imaging, high flux devices, metrology and interferometry. The problems to solve and the aims of the group in each of these cases are presented. Three synthesis of lectures are in this report. The main one concerns stigmatism conditions of concave holographic gratings used in normal incidence. This new process of focusing is very interesting for hot plasma diagnostics [fr

  18. Cobimaximal neutrino mixing from S3 × Z2

    Science.gov (United States)

    Ma, Ernest

    2018-02-01

    It has recently been shown that the phenomenologically successful pattern of cobimaximal neutrino mixing (θ13 ≠ 0, θ23 = π / 4, and δCP = ± π / 2) may be achieved in the context of the non-Abelian discrete symmetry A4. In this paper, the same goal is achieved with S3 ×Z2. The residual lepton Z3 triality in the case of A4 is replaced here by Z2 ×Z2. The associated phenomenology of the scalar sector is discussed.

  19. Experience with Server Self Service Center (S3C)

    CERN Multimedia

    Sucik, J

    2009-01-01

    CERN has a successful experience with running Server Self Service Center (S3C) for virtual server provisioning which is based on Microsoft® Virtual Server 2005. With the introduction of Windows Server 2008 and its built-in hypervisor based virtualization (Hyper-V) there are new possibilities for the expansion of the current service. This paper describes the architecture of the redesigned virtual Server Self Service based on Hyper-V which provides dynamically scalable virtualized resources on demand as needed and outlines the possible implications on the future use of virtual machines at CERN.

  20. Experience with Server Self Service Center (S3C)

    International Nuclear Information System (INIS)

    Sucik, Juraj; Bukowiec, Sebastian

    2010-01-01

    CERN has a successful experience with running Server Self Service Center (S3C) for virtual server provisioning which is based on Microsoft (registered) Virtual Server 2005. With the introduction of Windows Server 2008 and its built-in hypervisor based virtualization (Hyper-V) there are new possibilities for the expansion of the current service. This paper describes the architecture of the redesigned virtual Server Self Service based on Hyper-V which provides dynamically scalable virtualized resources on demand as needed and outlines the possible implications on the future use of virtual machines at CERN.

  1. Design and Characterization of the Ge/Ga2S3 Heterojunction

    Science.gov (United States)

    Al Garni, S. E.; Qasrawi, A. F.

    2017-08-01

    In this work, the formation and properties of Ga2S3 thin films deposited onto polycrystalline Ge substrates are studied by means of scanning electron microscopy, energy dispersive x-ray analyzer, Raman spectroscopy, x-ray diffraction techniques, ultraviolet-visible light spectrophotometry in the range of 300-1100 nm and by ac signal power spectroscopy in the range of 0.2-3.0 GHz. The first four techniques allowed the determining of the stoichiometry, the vibrational frequencies, the lattice parameters, the plane orientations, the strain and the defect density for the interface. In addition, it was observed that the Ge/Ga2S3 interface exhibited conduction and valence band offsets of 0.83 eV and 0.82 eV, respectively, and the real part of the dielectric spectra experimentally exhibited four resonance peaks centered at frequencies above 357 THz. Moreover, the computational analysis of the imaginary part of the dielectric constant via the Drude-Lorentz model has shown that the interface wave filtering properties are controlled by the electron-plasmon coupling with plasma frequencies in the range of 1.33-2.30 GHz. The drift mobility of electrons in this range was found to be 15.61 cm2/Vs. The real ability of the interface to control wave propagation was confirmed with ac signals propagating tests. The plasmonic features of the interface nominate it for use in microwave cavities and as wireless terahertz receivers.

  2. 12 CFR 7.2023 - Reverse stock splits.

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 1 2010-01-01 2010-01-01 false Reverse stock splits. 7.2023 Section 7.2023... Corporate Practices § 7.2023 Reverse stock splits. (a) Authority to engage in reverse stock splits. A national bank may engage in a reverse stock split if the transaction serves a legitimate corporate purpose...

  3. Fano resonance Rabi splitting of surface plasmons.

    Science.gov (United States)

    Liu, Zhiguang; Li, Jiafang; Liu, Zhe; Li, Wuxia; Li, Junjie; Gu, Changzhi; Li, Zhi-Yuan

    2017-08-14

    Rabi splitting and Fano resonance are well-known physical phenomena in conventional quantum systems as atoms and quantum dots, arising from strong interaction between two quantum states. In recent years similar features have been observed in various nanophotonic and nanoplasmonic systems. Yet, realization of strong interaction between two or more Fano resonance states has not been accomplished either in quantum or in optical systems. Here we report the observation of Rabi splitting of two strongly coupled surface plasmon Fano resonance states in a three-dimensional plasmonic nanostructure consisting of vertical asymmetric split-ring resonators. The plasmonic system stably supports triple Fano resonance states and double Rabi splittings can occur between lower and upper pairs of the Fano resonance states. The experimental discovery agrees excellently with rigorous numerical simulations, and is well explained by an analytical three-oscillator model. The discovery of Fano resonance Rabi splitting could provide a stimulating insight to explore new fundamental physics in analogous atomic systems and could be used to significantly enhance light-matter interaction for optical sensing and detecting applications.

  4. Photochemical Water-Splitting with Organomanganese Complexes.

    Science.gov (United States)

    Kadassery, Karthika J; Dey, Suman Kr; Cannella, Anthony F; Surendhran, Roshaan; Lacy, David C

    2017-08-21

    Certain organometallic chromophores with water-derived ligands, such as the known [Mn(CO) 3 (μ 3 -OH)] 4 (1) tetramer, drew our attention as possible platforms to study water-splitting reactions. Herein, we investigate the UV irradiation of various tricarbonyl organomanganese complexes, including 1, and demonstrate that dihydrogen, CO, and hydrogen peroxide form as products in a photochemical water-splitting decomposition reaction. The organic and manganese-containing side products are also characterized. Labeling studies with 18 O-1 suggest that the source of oxygen atoms in H 2 O 2 originates from free water that interacts with 1 after photochemical dissociation of CO (1-CO) constituting the oxidative half-reaction of water splitting mediated by 1. Hydrogen production from 1 is the result of several different processes, one of which involves the protons derived from the hydroxido ligands in 1 constituting the reductive half-reaction of water splitting mediated by 1. Other processes that generate H 2 are also operative and are described. Collectively the results from the photochemical decomposition of 1 provide an opportunity to propose a mechanism, and it is discussed within the context of developing new strategies for water-splitting reactions with organomanganese complexes.

  5. Split-hand/split-foot malformation with paternal mutation in the p63 gene.

    NARCIS (Netherlands)

    Witters, I.; Bokhoven, J.H.L.M. van; Goossens, A.; Assche, F.A. van; Fryns, J.P.

    2001-01-01

    We report the prenatal diagnosis at 16 weeks' gestation of bilateral split-hand/split-foot malformation (SHSFM) with severe lobster claw deformity of hands and feet in a male fetus without associated malformations. A minor manifestation of SHSFM was present in the father with only mild bilateral

  6. Urban pattern: Layout design by hierarchical domain splitting

    KAUST Repository

    Yang, Yongliang

    2013-11-06

    We present a framework for generating street networks and parcel layouts. Our goal is the generation of high-quality layouts that can be used for urban planning and virtual environments. We propose a solution based on hierarchical domain splitting using two splitting types: streamline-based splitting, which splits a region along one or multiple streamlines of a cross field, and template-based splitting, which warps pre-designed templates to a region and uses the interior geometry of the template as the splitting lines. We combine these two splitting approaches into a hierarchical framework, providing automatic and interactive tools to explore the design space.

  7. Large Bandgap Semiconductors for Solar Water Splitting

    DEFF Research Database (Denmark)

    Malizia, Mauro

    Photoelectrochemical water splitting represents an eco-friendly technology that could enable the production of hydrogen using water as reactant and solar energy as primary energy source. The exploitation of solar energy for the production of hydrogen would help modern society to reduce the reliance...... (bismuth vanadate) was investigated in view of combining this 2.4 eV large bandgap semiconductor with a Si back-illuminated photocathode. A device obtained by mechanical stacking of BiVO4 photoanode and standard Si photocathode performs non-assisted water splitting under illumination with Solar......-to-Hydrogen efficiency lower than 0.5%. In addition, BiVO4 was synthesized on the back-side of a Si back-illuminated photocathode to produce a preliminary monolithic solar water splitting device.The Faradaic efficiency of different types of catalysts for the electrochemical production of hydrogen or oxygen was evaluated...

  8. Multiple spectral splits of supernova neutrinos.

    Science.gov (United States)

    Dasgupta, Basudeb; Dighe, Amol; Raffelt, Georg G; Smirnov, Alexei Yu

    2009-07-31

    Collective oscillations of supernova neutrinos swap the spectra f(nu(e))(E) and f(nu[over ](e))(E) with those of another flavor in certain energy intervals bounded by sharp spectral splits. This phenomenon is far more general than previously appreciated: typically one finds one or more swaps and accompanying splits in the nu and nu[over ] channels for both inverted and normal neutrino mass hierarchies. Depending on an instability condition, swaps develop around spectral crossings (energies where f(nu(e))=f(nu(x)), f(nu[over ](e))=f(nu[over ](x)) as well as E-->infinity where all fluxes vanish), and the widths of swaps are determined by the spectra and fluxes. Washout by multiangle decoherence varies across the spectrum and splits can survive as sharp spectral features.

  9. Split Notochord Syndrome: A Rare Variant

    Science.gov (United States)

    Dhawan, Vidhu; Kapoor, Kanchan; Singh, Balbir; Kochhar, Suman; Sehgal, Alka; Dada, Rima

    2017-01-01

    Split notochord syndrome represents an extremely rare and pleomorphic form of spinal dysraphism characterized by a persistent communication between the endoderm and the ectoderm, resulting in splitting or deviation of the notochord. It manifests as a cleft in the dorsal midline of the body through which intestinal loops are exteriorized and even myelomeningoceles or teratomas may occur at the site. A rare variant was diagnosed on autopsy of a 23+4-week-old fetus showing a similar dorsal enteric fistula and midline protruding intestinal loops in thoracolumbar region. The anteroposterior radiograph showed a complete midline cleft in the vertebral bodies from T11 to L5 region, and a split in the spinal cord was further confirmed by ultrasonography. Myelomeningocele was erroneously reported on antenatal ultrasound. Thus, awareness of this rare anomaly is necessary to thoroughly evaluate the cases of such spinal defects or suspected myelomeningoceles. PMID:28904581

  10. Fuzzy split and merge for shadow detection

    Directory of Open Access Journals (Sweden)

    Remya K. Sasi

    2015-03-01

    Full Text Available Presence of shadow in an image often causes problems in computer vision applications such as object recognition and image segmentation. This paper proposes a method to detect the shadow from a single image using fuzzy split and merge approach. Split and merge is a classical algorithm used in image segmentation. Predicate function in the classical approach is replaced by a Fuzzy predicate in the proposed approach. The method follows a top down approach of recursively splitting an image into homogeneous quadtree blocks, followed by a bottom up approach by merging adjacent unique regions. The method has been compared with previous approaches and found to be better in performance in terms of accuracy.

  11. Phonon dispersion relations of Sb2S3 and Bi2S3 using the supercell force-constant method

    Science.gov (United States)

    Gan, Chee Kwan; Chua, Kun Ting Eddie; Liu, Yun

    2015-03-01

    We present a lattice dynamical study on the orthorhombic antimony sulphide (Sb2S3) and bismuth sulphide (Bi2S3) using the supercell force-constant method. We find that the slow decay of the interatomic force constants for these compounds in the Pnma setting critically demand the use of a large supercell of 2 × 4 × 2 that consists of 320 atoms. To enable a practical calculation the space group information is fully utilized where only inequivalent atoms within the primitive cell are displaced for the force calculations. The effect of Born effective charges is incorporated into the method. We compare our results with that obtained from the density-functional perturbation theory. We found that smaller supercells could lead to unphysical acoustic phonon softening and lifting of the degeneracies along high symmetry directions. Our results provide a proper guideline for the use of the supercell force-constant method: the supercell size must be carefully be tested along with other parameters such as the kinetic energy cutoff, the Brillouin zone sampling or the self-consistent convergence criteria.

  12. Spontaneous symmetry breaking in the $S_3$-symmetric scalar sector

    CERN Document Server

    Emmanuel-Costa, D.; Osland, P.; Rebelo, M.N.

    2016-02-23

    We present a detailed study of the vacua of the $S_3$-symmetric three-Higgs-doublet potential, specifying the region of parameters where these minimisation solutions occur. We work with a CP conserving scalar potential and analyse the possible real and complex vacua with emphasis on the cases in which the CP symmetry can be spontaneously broken. Results are presented both in the reducible-representation framework of Derman, and in the irreducible-representation framework. Mappings between these are given. Some of these implementations can in principle accommodate dark matter and for that purpose it is important to identify the residual symmetries of the potential after spontaneous symmetry breakdown. We are also concerned with constraints from vacuum stability.

  13. Colliding waves on a string in AdS$_3$

    CERN Document Server

    Vegh, David

    2015-01-01

    This paper is concerned with the classical motion of a string in global AdS$_3$. The initially static string stretches between two antipodal points on the boundary circle. Both endpoints are perturbed which creates cusps at a steady rate. The cusps propagate towards the interior where they collide. The behavior of the string depends on the strength of forcing. Three qualitatively different phases can be distinguished: transparent, gray, and black. The transparent region is analogous to a standing wave. In the black phase, there is a horizon on the worldsheet and cusps never reach the other endpoint. The string keeps folding and its length grows linearly over time. In the gray phase, the string still grows linearly. However, cusps do cross to the other side. The transparent and gray regions are separated by a transition point where a logarithmic accumulation of cusps is numerically observed. A simple model reproduces the qualitative behavior of the string in the three phases.

  14. Higher-derivative superparticle in AdS3 space

    Science.gov (United States)

    Kozyrev, Nikolay; Krivonos, Sergey; Lechtenfeld, Olaf

    2016-03-01

    Employing the coset approach we construct component actions for a superparticle moving in AdS3 with N =(2 ,0 ), D =3 supersymmetry partially broken to N =2 , d =1 . These actions may contain higher time-derivative terms, which are chosen to possess the same (super)symmetries as the free superparticle. In terms of the nonlinear-realization superfields, the component actions always take a simpler form when written in terms of covariant Cartan forms. We also consider in detail the reduction to the nonrelativistic case and construct the corresponding action of a Newton-Hooke superparticle and its higher-derivative generalizations. The structure of these higher time-derivative generalizations is completely fixed by invariance under the supersymmetric Newton-Hooke algebra extended by two central charges.

  15. Faster multiple emulsification with drop splitting.

    Science.gov (United States)

    Abate, Adam R; Weitz, David A

    2011-06-07

    Microfluidic devices can form emulsions in which the drops have an intricate, controlled structure; however, a challenge is that the droplets are produced slowly, typically only a few millilitres per hour. Here, we present a simple technique to increase the production rate. Using a large drop maker, we produce large drops at a fast volumetric rate; by splitting these drops several times in a splitting array, we create drops of the desired small size. The advantage of this over forming the small drops directly using a small drop maker is that the drops can be formed at much faster rates. This can be applied to the production of single and multiple emulsions.

  16. Splitting Strategy for Simulating Genetic Regulatory Networks

    Directory of Open Access Journals (Sweden)

    Xiong You

    2014-01-01

    Full Text Available The splitting approach is developed for the numerical simulation of genetic regulatory networks with a stable steady-state structure. The numerical results of the simulation of a one-gene network, a two-gene network, and a p53-mdm2 network show that the new splitting methods constructed in this paper are remarkably more effective and more suitable for long-term computation with large steps than the traditional general-purpose Runge-Kutta methods. The new methods have no restriction on the choice of stepsize due to their infinitely large stability regions.

  17. Hyperfine splitting in lithium-like bismuth

    Energy Technology Data Exchange (ETDEWEB)

    Lochmann, Matthias; Froemmgen, Nadja; Hammen, Michael; Will, Elisa [Universitaet Mainz (Germany); Andelkovic, Zoran; Kuehl, Thomas; Litvinov, Yuri; Winters, Danyal; Sanchez, Rodolfo [GSI Helmholtzzentrum, Darmstadt (Germany); Botermann, Benjamin; Noertershaeuser, Wilfried [Technische Universitaet Darmstadt (Germany); Bussmann, Michael [Helmholtzzentrum Dresden-Rossendorf (Germany); Dax, Andreas [CERN, Genf (Switzerland); Hannen, Volker; Joehren, Raphael; Vollbrecht, Jonas; Weinheimer, Christian [Universitaet Muenster (Germany); Geppert, Christopher [Universitaet Mainz (Germany); GSI Helmholtzzentrum, Darmstadt (Germany); Stoehlker, Thomas [GSI Helmholtzzentrum, Darmstadt (Germany); Universitaet Heidelberg (Germany); Thompson, Richard [Imperial College, London (United Kingdom); Volotka, Andrey [Technische Universitaet Dresden (Germany); Wen, Weiqiang [IMP Lanzhou (China)

    2013-07-01

    High-precision measurements of the hyperfine splitting values on Li- and H-like bismuth ions, combined with precise atomic structure calculations allow us to test QED-effects in the regime of the strongest magnetic fields that are available in the laboratory. Performing laser spectroscopy at the experimental storage ring (ESR) at GSI Darmstadt, we have now succeeded in measuring the hyperfine splitting in Li-like bismuth. Probing this transition has not been easy because of its extremely low fluorescence rate. Details about this challenging experiment will be given and the achieved experimental accuracy are presented.

  18. Analysis of mobile fronthaul bandwidth and wireless transmission performance in split-PHY processing architecture.

    Science.gov (United States)

    Miyamoto, Kenji; Kuwano, Shigeru; Terada, Jun; Otaka, Akihiro

    2016-01-25

    We analyze the mobile fronthaul (MFH) bandwidth and the wireless transmission performance in the split-PHY processing (SPP) architecture, which redefines the functional split of centralized/cloud RAN (C-RAN) while preserving high wireless coordinated multi-point (CoMP) transmission/reception performance. The SPP architecture splits the base stations (BS) functions between wireless channel coding/decoding and wireless modulation/demodulation, and employs its own CoMP joint transmission and reception schemes. Simulation results show that the SPP architecture reduces the MFH bandwidth by up to 97% from conventional C-RAN while matching the wireless bit error rate (BER) performance of conventional C-RAN in uplink joint reception with only 2-dB signal to noise ratio (SNR) penalty.

  19. Discrete objects, splitting closure and connectedness | Castellini ...

    African Journals Online (AJOL)

    Notions of discrete and indiscrete classes with respect to a closure operator are introduced and studied. These notions are strongly related to splitting and cosplitting closure operators. By linking the above concepts, two Galois connections arise whose composition provides a third Galois connection that can be used as a ...

  20. Miniaturized Planar Split-Ring Resonator Antenna

    DEFF Research Database (Denmark)

    Kim, Oleksiy S.; Breinbjerg, Olav

    2009-01-01

    A miniaturized planar antenna based on a broadside-coupled split ring resonator excited by an arc-shaped dipole is presented. The excitation dipole acts as a small tuning capacitor in series with a parallel RLC circuit represented by the SRR. The antenna resonance frequency and dimensions...

  1. Split Coil Forms for Rotary Transformers

    Science.gov (United States)

    Mclyman, C. W. T.

    1982-01-01

    Split cores for rotor and stator windings of rotary transformer mounted around their respective coils (which are in bobbins) and cemented together. This arrangement simplifies winding of stator coil to go in a slot in inner diameter of stator coil. One practical application of rotary transformers fabricated according to this technique is for centrifuges, in which conventional sliprings are of uncertain reliability.

  2. Split Beta-Lactamase Complementation Assay

    Indian Academy of Sciences (India)

    IAS Admin

    Concept of split beta. -lactamase protein fragment complementation assay. (A) and (B) are vector systems involved in the assay. As an example, a vector system for bacterial host is described here. (C) Co-transformation of complementation vectors in appropriate bacterial host. (D) and (E) are types of inter- actions expected ...

  3. Molecular catalytic system for efficient water splitting

    NARCIS (Netherlands)

    Joya, Khurram Saleem

    2011-01-01

    The aim of this dissertation is to construct and explore artificial oxygen evolving complexes that are synthetically accessible, stable, functionally robust and efficient. To achieve this, a class of mono metal water splitting catalysts is introduced in this manuscript and exploitation of these

  4. Splitting up Beta’s change

    OpenAIRE

    Suarez, Ronny

    2014-01-01

    In this paper we estimated IBM beta from 2000 to 2013, then using differential equation mathematical formula we split up the annual beta’s change attributed to the volatility market effect, the stock volatility effect, the correlation effect and the jointly effect of these variables.

  5. Shear-wave splitting and moonquakes

    Science.gov (United States)

    Dimech, J. L.; Weber, R. C.; Savage, M. K.

    2017-12-01

    Shear-wave splitting is a powerful tool for measuring anisotropy in the Earth's crust and mantle, and is sensitive to geological features such as fluid filled cracks, thin alternating layers of rock with different elastic properties, and preferred mineral orientations caused by strain. Since a shear wave splitting measurement requires only a single 3-component seismic station, it has potential applications for future single-station planetary seismic missions, such as the InSight geophysical mission to Mars, as well as possible future missions to Europa and the Moon. Here we present a preliminary shear-wave splitting analysis of moonquakes detected by the Apollo Passive Seismic Experiment. Lunar seismic data suffers from several drawbacks compared to modern terrestrial data, including severe seismic scattering, low intrinsic attenuation, 10-bit data resolution, thermal spikes, and timing errors. Despite these drawbacks, we show that it is in principle possible to make a shear wave splitting measurement using the S-phase arrival of a relatively high-quality moonquake, as determined by several agreeing measurement criteria. Encouraged by this finding, we further extend our analysis to clusters of "deep moonquake" events by stacking multiple events from the same cluster together to further enhance the quality of the S-phase arrivals that the measurement is based on.

  6. Split brain: divided perception but undivided consciousness.

    Science.gov (United States)

    Pinto, Yair; Neville, David A; Otten, Marte; Corballis, Paul M; Lamme, Victor A F; de Haan, Edward H F; Foschi, Nicoletta; Fabri, Mara

    2017-05-01

    In extensive studies with two split-brain patients we replicate the standard finding that stimuli cannot be compared across visual half-fields, indicating that each hemisphere processes information independently of the other. Yet, crucially, we show that the canonical textbook findings that a split-brain patient can only respond to stimuli in the left visual half-field with the left hand, and to stimuli in the right visual half-field with the right hand and verbally, are not universally true. Across a wide variety of tasks, split-brain patients with a complete and radiologically confirmed transection of the corpus callosum showed full awareness of presence, and well above chance-level recognition of location, orientation and identity of stimuli throughout the entire visual field, irrespective of response type (left hand, right hand, or verbally). Crucially, we used confidence ratings to assess conscious awareness. This revealed that also on high confidence trials, indicative of conscious perception, response type did not affect performance. These findings suggest that severing the cortical connections between hemispheres splits visual perception, but does not create two independent conscious perceivers within one brain. © The Author (2017). Published by Oxford University Press on behalf of the Guarantors of Brain. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  7. Helioseismic Solar Cycle Changes and Splitting Coefficients

    Indian Academy of Sciences (India)

    tribpo

    Abstract. Using the GONG data for a period over four years, we have studied the variation of frequencies and splitting coefficients with solar cycle. Frequencies and even-order coefficients are found to change signi- ficantly with rising phase of the solar cycle. We also find temporal varia- tions in the rotation rate near the solar ...

  8. Czech, Slovak science ten years after split

    CERN Multimedia

    2003-01-01

    Ten years after the split of Czechoslovakia Czech and Slovak science are facing the same difficulties: shortage of money for research, poor salaries, obsolete equipment and brain drain, especially of the young, according to a feature in the Daily Lidove Noviny (1 page).

  9. Comparing Electrochemical and Biological Water Splitting

    DEFF Research Database (Denmark)

    Rossmeisl, Jan; Dimitrievski, Kristian; Siegbahn, P.

    2007-01-01

    On the basis of density functional theory calculations, we compare the free energies of key intermediates in the water splitting reaction over transition metal oxide surfaces to those of the Mn cluster in photo system II. In spite of the very different environments in the enzyme system...

  10. F-theory and AdS3/CFT2

    Science.gov (United States)

    Couzens, Christopher; Lawrie, Craig; Martelli, Dario; Schäfer-Nameki, Sakura; Wong, Jin-Mann

    2017-08-01

    We construct supersymmetric AdS3 solutions in F-theory, that is Type IIB supergravity with varying axio-dilaton, which are holographically dual to 2d N=(0,4) superconformal field theories with small superconformal algebra. In F-theory these arise from D3-branes wrapped on curves in the base of an elliptically fibered Calabi-Yau threefold Y 3 and correspond to self-dual strings in the 6d N=(1,0) theory obtained from F-theory on Y 3. The non-trivial fibration over the wrapped curves implies a varying coupling of the N=4 Super-Yang-Mills theory on the D3-branes. We compute the holographic central charges and show that these agree with the field theory and with the anomalies of self-dual strings in 6d. We complement our analysis with a discussion of the dual M-theory solutions and a comparison of the central charges.

  11. Nonequilibrium spin transport in Zeeman-split superconductors

    Science.gov (United States)

    Krishtop, Tatiana; Houzet, Manuel; Meyer, Julia S.

    2015-03-01

    We investigate theoretically the nonlocal conductance through a superconducting wire in tunnel contact with normal and ferromagnetic leads. In the presence of an in-plane magnetic field, the superconducting density of states is spin split, and the current injected from the normal lead is spin polarized. A nonlocal conductance that is antisymmetric with the applied voltage can be measured with a ferromagnetic lead. It persists for a distance between the contacts that is larger than both the charge-imbalance relaxation length and the normal-state spin relaxation length. We determine its amplitude by considering two extreme models of weak and strong internal equilibration of the superconducting quasiparticles due to electron-electron interactions. We find that the nonlocal signal, which was measured in recent experiments and discussed as a spin-imbalance effect, can be interpreted alternatively as the signature of a thermoelectric effect.

  12. Etudes des verres du pseudo-ternaire La 2S 3Bi 2S 3Ga 2S 3, en relation avec le diagramme de phases et la spectroscopie infra-rouge

    Science.gov (United States)

    Ecrepont, C.; Guittard, M.; Barnier, S.; Loireau-Lozac'h, A. M.; Palazzi, M.; Julien, C.; Massot, M.

    1992-04-01

    The phase diagram of the La 2S 3Ga 2S 3Bi 2S 3 ternary system is described. DTA measurements have been carried out on a large variety of glass, and the glass formation domain has been defined with the investigation of Tg, Tc, and the endothermic peaks. Infrared absorption spectra have been studied. The vibrational assignment is discussed in relation to the composition of the glass.

  13. Growth rate controlled synthesis of hierarchical Bi2S3/In2S3 core/shell microspheres with enhanced photocatalytic activity

    Science.gov (United States)

    Zhou, Juan; Tian, Guohui; Chen, Yajie; Shi, Yunhan; Tian, Chungui; Pan, Kai; Fu, Honggang

    2014-02-01

    Core/shell heterostructure composite has great potential applications in photocatalytic field because the introduction of core can remarkably improve charge transport and enhance the electron-hole separation. Herein, hierarchical Bi2S3/In2S3 core/shell structured microspheres were prepared via a simple one-pot hydrothermal process based on different growth rate of the two kinds of sulphides. The results showed that, the as-prepared hierarchical Bi2S3/In2S3 core/shell heterostructure exhibits significant visible light photocatalytic activity for degradation of 2, 4-dichlorophenol. The introduction of Bi2S3 core can not only improve charge transport and enhance the electron-hole separation, but also broaden the visible light response. The hierarchical porous folwer-like shell of In2S3 could increase the specific surface area and remarkably enhanced the chemical stability of Bi2S3 against oxidation.

  14. Non-Mendelian transmission in a human developmental disorder: split hand/split foot.

    OpenAIRE

    Jarvik, G. P.; Patton, M. A.; Homfray, T.; Evans, J. P.

    1994-01-01

    The study of Mendelian disorders that do not meet some Mendelian expectations has led to an increased understanding of such previously obscure genetic phenomena as anticipation. Split hand/split foot (SHSF), a human developmental malformation, demonstrates such distinctive genetic features as reduced penetrance and variable expressivity. In this study, new pedigrees with defined ascertainment confirm the existence of non-Mendelian transmission characterized by the overtransmission of SHSF fro...

  15. Splitting, splitting and splitting again: A brief history of the development of regional government in Indonesia since independence

    Directory of Open Access Journals (Sweden)

    Anne Booth

    2011-04-01

    Full Text Available The paper reviews the changes in the structure and role of provincial and sub-provincial governments in Indonesia since independence. Particular attention is paid to the process of splitting both provinces and districts (kabupaten and kota into smaller units. The paper points out that this process has been going on since the 1950s, but has accelerated in the post-Soeharto era. The paper examines why the splitting of government units has occurred in some parts of the Outer Islands to a much greater extent than in Java, and also examines the implications of developments since 1999 for the capacity of local government units to deliver basic services such as health and education.

  16. Full-Color Emission From In2S3 and In2S3:Eu3+ Nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Wei; Bovin, Jan-Olov; Joly, Alan G.; Wang, Shaopeng; Su, Fuhai; Li, Guohua

    2004-08-12

    Blue (425 nm) and green (510 nm) emission is observed from In2S3 nanoparticles which are synthesized using a novel method. Both the blue and green emissions have large Stokes shifts of 62 and 110 nm, respectively. Excitation with longer wavelength photons causes the blue emission to shift to longer wavelength while the green emission wavelength remains unchanged. The lifetimes of both green and blue emissions are similar to reported values for excitonic recombination. When doped with Eu3+, in addition to the broad blue and green emissions, a red emission at 615 nm attributed to Eu3+ is observed. Temperature dependences on nanoparticle thin films indicate that with increasing temperature, the green emission wavelength remains constant, however, the blue emission shifts toward longer wavelengths. Based on these observations, the blue emission is attributed to exciton recombination and the green emission to Indium interstitial defects. These nanoparticles show full-color emission with high efficiency, fast lifetime decays, good stability, and are relatively simple to prepare thus making them a new type of phosphor with potential applications in lighting, flat-panel displays, and communications.

  17. Full-Color Emission From In2S3 and In2S3:Eu3+ Nanoparticles

    International Nuclear Information System (INIS)

    Chen, Wei; Bovin, Jan-Olov; Joly, Alan G.; Wang, Shaopeng; Su, Fuhai; Li, Guohua

    2004-01-01

    Blue (425 nm) and green (510 nm) emission is observed from In2S3 nanoparticles which are synthesized using a novel method. Both the blue and green emissions have large Stokes shifts of 62 and 110 nm, respectively. Excitation with longer wavelength photons causes the blue emission to shift to longer wavelength while the green emission wavelength remains unchanged. The lifetimes of both green and blue emissions are similar to reported values for excitonic recombination. When doped with Eu3+, in addition to the broad blue and green emissions, a red emission at 615 nm attributed to Eu3+ is observed. Temperature dependences on nanoparticle thin films indicate that with increasing temperature, the green emission wavelength remains constant, however, the blue emission shifts toward longer wavelengths. Based on these observations, the blue emission is attributed to exciton recombination and the green emission to Indium interstitial defects. These nanoparticles show full-color emission with high efficiency, fast lifetime decays, good stability, and are relatively simple to prepare thus making them a new type of phosphor with potential applications in lighting, flat-panel displays, and communications

  18. Split mandrel versus split sleeve coldworking: Dual methods for extending the fatigue life of metal structures

    Science.gov (United States)

    Rodman, Geoffrey A.; Creager, Matthew

    1994-01-01

    It is common practice to use split sleeve coldworking of fastener holes as a means of extending the fatigue life of metal structures. In search of lower manufacturing costs, the aerospace industry is examining the split mandrel (sleeveless) coldworking process as an alternative method of coldworking fastener holes in metal structures. The split mandrel process (SpM) significantly extends the fatigue life of metal structures through the introduction of a residual compressive stress in a manner that is very similar to the split sleeve system (SpSl). Since the split mandrel process is significantly less expensive than the split sleeve process and more adaptable to robotic automation, it will have a notable influence upon other new manufacture of metal structures which require coldworking a significant number of holes, provided the aerospace community recognizes that the resulting residual stress distributions and fatigue life improvement are the same for both processes. Considerable testing has validated the correctness of that conclusion. The findings presented in this paper represent the results of an extensive research and development program, comprising data collected from over 400 specimens fabricated from 2024-T3 and 7075-T651 aluminum alloys in varied configurations, which quantify the benefits (fatigue enhancement and cost savings) of automating a sleeveless coldworking system.

  19. Photoelectrochemical water splitting: optimizing interfaces and light absorption

    NARCIS (Netherlands)

    Park, Sun-Young

    2015-01-01

    In this thesis several photoelectrochemical water splitting devices based on semiconductor materials were investigated. The aim was the design, characterization, and fabrication of solar-to-fuel devices which can absorb solar light and split water to produce hydrogen.

  20. A Regularized Algorithm for the Proximal Split Feasibility Problem

    Directory of Open Access Journals (Sweden)

    Zhangsong Yao

    2014-01-01

    Full Text Available The proximal split feasibility problem has been studied. A regularized method has been presented for solving the proximal split feasibility problem. Strong convergence theorem is given.

  1. Multiple Rabi Splittings under Ultrastrong Vibrational Coupling.

    Science.gov (United States)

    George, Jino; Chervy, Thibault; Shalabney, Atef; Devaux, Eloïse; Hiura, Hidefumi; Genet, Cyriaque; Ebbesen, Thomas W

    2016-10-07

    From the high vibrational dipolar strength offered by molecular liquids, we demonstrate that a molecular vibration can be ultrastrongly coupled to multiple IR cavity modes, with Rabi splittings reaching 24% of the vibration frequencies. As a proof of the ultrastrong coupling regime, our experimental data unambiguously reveal the contributions to the polaritonic dynamics coming from the antiresonant terms in the interaction energy and from the dipolar self-energy of the molecular vibrations themselves. In particular, we measure the opening of a genuine vibrational polaritonic band gap of ca. 60 meV. We also demonstrate that the multimode splitting effect defines a whole vibrational ladder of heavy polaritonic states perfectly resolved. These findings reveal the broad possibilities in the vibrational ultrastrong coupling regime which impact both the optical and the molecular properties of such coupled systems, in particular, in the context of mode-selective chemistry.

  2. Splitting of high power, cw proton beams

    Directory of Open Access Journals (Sweden)

    Alberto Facco

    2007-09-01

    Full Text Available A simple method for splitting a high power, continuous wave (cw proton beam in two or more branches with low losses has been developed in the framework of the EURISOL (European Isotope Separation On-Line Radioactive Ion Beam Facility design study. The aim of the system is to deliver up to 4 MW of H^{-} beam to the main radioactive ion beam production target, and up to 100 kW of proton beams to three more targets, simultaneously. A three-step method is used, which includes magnetic neutralization of a fraction of the main H^{-} beam, magnetic splitting of H^{-} and H^{0}, and stripping of H^{0} to H^{+}. The method allows slow raising and individual fine adjustment of the beam intensity in each branch.

  3. Meshed split skin graft for extensive vitiligo

    Directory of Open Access Journals (Sweden)

    Srinivas C

    2004-05-01

    Full Text Available A 30 year old female presented with generalized stable vitiligo involving large areas of the body. Since large areas were to be treated it was decided to do meshed split skin graft. A phototoxic blister over recipient site was induced by applying 8 MOP solution followed by exposure to UVA. The split skin graft was harvested from donor area by Padgett dermatome which was meshed by an ampligreffe to increase the size of the graft by 4 times. Significant pigmentation of the depigmented skin was seen after 5 months. This procedure helps to cover large recipient areas, when pigmented donor skin is limited with minimal risk of scarring. Phototoxic blister enables easy separation of epidermis thus saving time required for dermabrasion from recipient site.

  4. Timelike single-logarithm-resummed splitting functions

    International Nuclear Information System (INIS)

    Albino, S.; Bolzoni, P.; Kniehl, B.A.; Kotikov, A.V.; Joint Inst. of Nuclear Research, Moscow

    2011-08-01

    We calculate the single logarithmic contributions to the quark singlet and gluon matrix of timelike splitting functions at all orders in the modified minimal-subtraction (MS) scheme. We fix two of the degrees of freedom of this matrix from the analogous results in the massive-gluon regularization scheme by using the relation between that scheme and the MS scheme. We determine this scheme transformation from the double logarithmic contributions to the timelike splitting functions and the coefficient functions of inclusive particle production in e + e - annihilation now available in both schemes. The remaining two degrees of freedom are fixed by reasonable physical assumptions. The results agree with the fixed-order results at next-to-next-to-leading order in the literature. (orig.)

  5. Solar Water Splitting Using Semiconductor Photocatalyst Powders

    KAUST Repository

    Takanabe, Kazuhiro

    2015-07-01

    Solar energy conversion is essential to address the gap between energy production and increasing demand. Large scale energy generation from solar energy can only be achieved through equally large scale collection of the solar spectrum. Overall water splitting using heterogeneous photocatalysts with a single semiconductor enables the direct generation of H from photoreactors and is one of the most economical technologies for large-scale production of solar fuels. Efficient photocatalyst materials are essential to make this process feasible for future technologies. To achieve efficient photocatalysis for overall water splitting, all of the parameters involved at different time scales should be improved because the overall efficiency is obtained by the multiplication of all these fundamental efficiencies. Accumulation of knowledge ranging from solid-state physics to electrochemistry and a multidisciplinary approach to conduct various measurements are inevitable to be able to understand photocatalysis fully and to improve its efficiency.

  6. Atom beams split by gentle persuasion

    International Nuclear Information System (INIS)

    Pool, R.

    1994-01-01

    Two different research teams have taken a big step toward atom interferometry. They have succeeded in splitting atomic beams by using atoms in spin states that neither absorb nor reemit laser light. By proper adjustment of experimental conditions, atoms are changed from one spin state to another, without passing through the intermediary excited state. The atoms in essence absorb momentum from the laser photons, without absorption or emission of photons. The change in momentum deflects atoms in the proper spin state

  7. On split Lie triple systems II

    Indian Academy of Sciences (India)

    In the present paper we extend these results to arbitrary split Lie triple systems with no restrictions on their 0-root spaces. Author Affiliations. Antonio J Calderón Martín1 M Forero Piulestán1. Departamento de Matemáticas, Universidad de Cádiz, 11510 Puerto Real, Cádiz, Spain. Dates. Manuscript received: 24 June 2009 ...

  8. Transonymization as Revitalization: Old Toponyms of Split

    Directory of Open Access Journals (Sweden)

    Katarina Lozić Knezović

    2017-07-01

    Full Text Available The paper deals with ancient toponyms of Split, a city in the centre of the Croatian region of Dalmatia. Along with numerous monuments of spiritual and material culture, toponyms are part of the two-thousand-year-old city’s historical heritage. Split in particular abounds with sources that provide valuable information concerning ancient toponyms. In terms of the study and preservation of toponymy, three basic sources are crucial: the living oral tradition, written records, and old charts — mostly cadastral plans. In addition to researching, recording, documenting, and publishing Split’s ancient place names through toponomastic, geographical, and town planning studies, toponymic heritage preservation is also implemented through the direct use of the names in everyday life. One of the ways of such revitalization of Split’s ancient place names is their transonymization into the category of chrematonyms, i.e. their secondary use as names of institutions, shops, restaurants, schools, sports associations and facilities, bars and coffee shops, cemeteries, and so on. The present paper provides a classification and etymological analysis of detoponymic chrematonyms of Split. The authors propose measures to raise public awareness of the historical information conveyed by the names and raise some issues for consideration regarding further study of transonymization as a means of revitalizing local toponymic tradition.

  9. 26 CFR 1.7872-15 - Split-dollar loans.

    Science.gov (United States)

    2010-04-01

    ...) INCOME TAXES General Actuarial Valuations § 1.7872-15 Split-dollar loans. (a) General rules—(1... split-dollar loan depend upon the relationship between the parties and upon whether the loan is a demand...-dollar demand loan is any split-dollar loan that is payable in full at any time on the demand of the...

  10. 7 CFR 51.2731 - U.S. Spanish Splits.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false U.S. Spanish Splits. 51.2731 Section 51.2731... STANDARDS) United States Standards for Grades of Shelled Spanish Type Peanuts Grades § 51.2731 U.S. Spanish Splits. “U.S. Spanish Splits” consists of shelled Spanish type peanut kernels which are split or broken...

  11. Smart Screening System (S3) In Taconite Processing

    Energy Technology Data Exchange (ETDEWEB)

    Daryoush Allaei; Asim Syed Mohammed; David Tarnowski; Angus Morison

    2005-03-01

    components include smart motor and associated electronics, resonators, and supporting structural elements. It is shown that the smart motors have an acceptable life and performance. Resonator (or motion amplifier) designs are selected based on the final system requirement and vibration characteristics. All the components for a fully functional prototype are fabricated. The development program is on schedule. The last semi-annual report described the need and the work accomplished to design a supporting structure. The modified supporting structure design improved system rigidity and integrity and helped improve overall system performance. Lab test results showed a significant improvement in reducing undesired supporting structure vibration, better system performance and ease of installation. However the system performance suffered severe losses due to installation requirement. Since then significant work was completed both in terms of analysis and experimentation to minimize system installation sensitivity and to relax plant structure foundation requirement. Lab test on the modified system are near completion and we plan to test the system in field in early next quarter. With the assistance of Albany Research center, strain measurements were successfully completed on the S3i-101 unit. This report also includes the work initiated to investigate feasibility of inserting SmartScreens{trademark} technology in the field of dry applications.

  12. Calculation of the zero-field splitting D and g(perp)parameters in EPR for d3 spin systems in strong and moderate axial fields

    NARCIS (Netherlands)

    Kool, Th.W.; Bollegraaf, B.

    2010-01-01

    Numerical and analytical methods are used to investigate the calculation of the zero field splitting |2D| and g(perp) parameters in EPR for octahedrally surrounded d3 spin systems (S = 3/2) in strong and moderate axial crystal fields (|D|>=h{\

  13. Semiconductor Nanowires for Photoelectrochemical Water Splitting

    Science.gov (United States)

    Hwang, Yun Jeong

    Photolysis of water with semiconductor materials has been investigated intensely as a clean and renewable energy resource by storing solar energy in chemical bonds such as hydrogen. One-dimensional (1D) nanostructures such as nanowires can provide several advantages for photoelectrochemical (PEC) water splitting due to their high surface areas and excellent charge transport and collection efficiency. This dissertation discusses various nanowire photoelectrodes for single or dual semiconductor systems, and their linked PEC cells for self-driven water splitting. After an introduction of solar water splitting in the first chapter, the second chapter demonstrates water oxidative activities of hydrothermally grown TiO2 nanowire arrays depending on their length and surface properties. The photocurrents with TiO2 nanowire arrays approach saturation due to their poor charge collection efficiency with longer nanowires despite increased photon absorption efficiency. Epitaxial grains of rutile atomic layer deposition (ALD) shell on TiO2 nanowire increase the photocurrent density by 1.5 times due to improved charge collection efficiency especially in the short wavelength region. Chapter three compares the photocurrent density of the planar Si and Si nanowire arrays coated by anatase ALD TiO 2 thin film as a model system of a dual bandgap system. The electroless etched Si nanowire coated by ALD TiO2 (Si EENW/TiO2) shows 2.5 times higher photocurrent density due to lower reflectance and higher surface area. Also, this chapter illustrates that n-Si/n-TiO2 heterojunction is a promising structure for the photoanode application of a dual semiconductor system, since it can enhance the photocurrent density compared to p-Si/n-TiO 2 junction with the assistance of bend banding at the interface. Chapter four demonstrates the charge separation and transport of photogenerated electrons and holes within a single asymmetric Si/TiO2 nanowire. Kelvin probe force microscopy measurements show

  14. Epigraphical splitting for solving constrained convex formulations of inverse problems with proximal tools

    OpenAIRE

    Chierchia, Giovanni; Pustelnik, Nelly; Pesquet, Jean-Christophe; Pesquet-Popescu, Béatrice

    2012-01-01

    We propose a proximal approach to deal with a class of convex variational problems involving nonlinear constraints. A large family of constraints, proven to be effective in the solution of inverse problems, can be expressed as the lower level set of a sum of convex functions evaluated over different, but possibly overlapping, blocks of the signal. For such constraints, the associated projection operator generally does not have a simple form. We circumvent this difficulty by splitting the lowe...

  15. Exact free oscillation spectra, splitting functions and the resolvability of Earth's density structure

    Science.gov (United States)

    Akbarashrafi, F.; Al-Attar, D.; Deuss, A.; Trampert, J.; Valentine, A. P.

    2018-04-01

    Seismic free oscillations, or normal modes, provide a convenient tool to calculate low-frequency seismograms in heterogeneous Earth models. A procedure called `full mode coupling' allows the seismic response of the Earth to be computed. However, in order to be theoretically exact, such calculations must involve an infinite set of modes. In practice, only a finite subset of modes can be used, introducing an error into the seismograms. By systematically increasing the number of modes beyond the highest frequency of interest in the seismograms, we investigate the convergence of full-coupling calculations. As a rule-of-thumb, it is necessary to couple modes 1-2 mHz above the highest frequency of interest, although results depend upon the details of the Earth model. This is significantly higher than has previously been assumed. Observations of free oscillations also provide important constraints on the heterogeneous structure of the Earth. Historically, this inference problem has been addressed by the measurement and interpretation of splitting functions. These can be seen as secondary data extracted from low frequency seismograms. The measurement step necessitates the calculation of synthetic seismograms, but current implementations rely on approximations referred to as self- or group-coupling and do not use fully accurate seismograms. We therefore also investigate whether a systematic error might be present in currently published splitting functions. We find no evidence for any systematic bias, but published uncertainties must be doubled to properly account for the errors due to theoretical omissions and regularization in the measurement process. Correspondingly, uncertainties in results derived from splitting functions must also be increased. As is well known, density has only a weak signal in low-frequency seismograms. Our results suggest this signal is of similar scale to the true uncertainties associated with currently published splitting functions. Thus, it seems

  16. Flow Cytometric Bead Sandwich Assay Based on a Split Aptamer.

    Science.gov (United States)

    Shen, Luyao; Bing, Tao; Liu, Xiangjun; Wang, Junyan; Wang, Linlin; Zhang, Nan; Shangguan, Dihua

    2018-01-24

    A few aptamers still bind their targets after being split into two moieties. Split aptamers have shown great potential in the development of aptameric sensors. However, only a few split aptamers have been generated because of lack of knowledge on the binding structure of their parent aptamers. Here, we report the design of a new split aptamer and a flow cytometric bead sandwich assay using a split aptamer instead of double antibodies. Through DMS footprinting and mutation assay, we figured out the target-binding moiety and the structure-stabilizing moiety of the l-selectin aptamer, Sgc-3b. By separating the duplex strand in the structure-stabilizing moiety, we obtained a split aptamer that bound l-selectin. After optimization of one part of the split sequence to eliminate the nonspecific binding of the split sequence pair, we developed a split-aptamer-based cytometric bead assay (SACBA) for the detection of soluble l-selectin. SACBA showed good sensitivity and selectivity to l-selectin and was successfully applied for the detection of spiked l-selectin in the human serum. The strategies for generating split aptamers and designing the split-aptamer-based sandwich assay are simple and efficient and show good practicability in aptamer engineering.

  17. SplitRFLab: A MATLAB GUI toolbox for receiver function analysis based on SplitLab

    Science.gov (United States)

    Xu, Mijian; Huang, Hui; Huang, Zhouchuan; Wang, Liangshu

    2016-02-01

    We add new modules for receiver function (RF) analysis in SplitLab toolbox, which includes the manual RF analysis module, automatic RF analysis and related quality control modules, and H- k stacking module. The updated toolbox (named SplitRFLab toolbox), especially its automatic RF analysis module, could calculate the RFs quickly and efficiently, which is very useful in RF analysis with huge amount of seismic data. China is now conducting the ChinArray project that plans to deploy thousands of portable stations across Chinese mainland. Our SplitRFLab toolbox may obtain reliable RF results quickly at the first time, which provide essentially new constraint to the crustal and mantle structures.

  18. Method of orthogonally splitting imaging pose measurement

    Science.gov (United States)

    Zhao, Na; Sun, Changku; Wang, Peng; Yang, Qian; Liu, Xintong

    2018-01-01

    In order to meet the aviation's and machinery manufacturing's pose measurement need of high precision, fast speed and wide measurement range, and to resolve the contradiction between measurement range and resolution of vision sensor, this paper proposes an orthogonally splitting imaging pose measurement method. This paper designs and realizes an orthogonally splitting imaging vision sensor and establishes a pose measurement system. The vision sensor consists of one imaging lens, a beam splitter prism, cylindrical lenses and dual linear CCD. Dual linear CCD respectively acquire one dimensional image coordinate data of the target point, and two data can restore the two dimensional image coordinates of the target point. According to the characteristics of imaging system, this paper establishes the nonlinear distortion model to correct distortion. Based on cross ratio invariability, polynomial equation is established and solved by the least square fitting method. After completing distortion correction, this paper establishes the measurement mathematical model of vision sensor, and determines intrinsic parameters to calibrate. An array of feature points for calibration is built by placing a planar target in any different positions for a few times. An terative optimization method is presented to solve the parameters of model. The experimental results show that the field angle is 52 °, the focus distance is 27.40 mm, image resolution is 5185×5117 pixels, displacement measurement error is less than 0.1mm, and rotation angle measurement error is less than 0.15°. The method of orthogonally splitting imaging pose measurement can satisfy the pose measurement requirement of high precision, fast speed and wide measurement range.

  19. Injuries caused by firewood splitting machines.

    Science.gov (United States)

    Hellstrand, P H

    1989-01-01

    The aim of this paper is to present the types of injury caused by firewood splitting machines and also to elucidate the accident mechanism. The study is based on 15 cases. The machine has a rotating spiral cone, and usually the victims' gloved fingertips were caught by the point of the cone. This led to either amputations, usually of radial fingers and/or penetrating wounds through the middle of the hand. In most cases the accidents could not be blamed on bad working techniques. The study of the mechanisms of injury points to insufficient protective devices in a machine construction which has a potentially dangerous working principle.

  20. Pt/In2S3/CdS/Cu2ZnSnS4 Thin Film as an Efficient and Stable Photocathode for Water Reduction under Sunlight Radiation.

    Science.gov (United States)

    Jiang, Feng; Gunawan; Harada, Takashi; Kuang, Yongbo; Minegishi, Tsutomu; Domen, Kazunari; Ikeda, Shigeru

    2015-10-28

    An electrodeposited Cu2ZnSnS4 (CZTS) compact thin film modified with an In2S3/CdS double layer and Pt deposits (Pt/In2S3/CdS/CZTS) was used as a photocathode for water splitting of hydrogen production under simulated sunlight (AM 1.5G) radiation. Compared to platinized electrodes based on a bare CZTS film (Pt/CZTS) and a CZTS film modified with a CdS single layer (Pt/CdS/CZTS), the Pt/In2S3/CdS/CZTS electrode exhibited a significantly high cathodic photocurrent. Moreover, the coverage of the In2S3 layer was found to be effective for stabilization against degradation induced by photocorrosion of the CdS layer. Bias-free water splitting with a power conversion efficiency of 0.28% was achieved by using a simple two-electrode cell consisting of the Pt/In2S3/CdS/CZTS photocathode and a BiVO4 photoanode.

  1. Superconducting Properties in Y-doped Semimetallic Bi3O2S3 Superconductors

    Science.gov (United States)

    Kim, Gun Cheol; Cheon, Miyeon; Ahmad, Dawood; Kwon, Yong Seung; Ko, Rock Kil; Kim, Young Cheol

    2018-02-01

    We report the superconducting properties of Y-doped semimetallic Bi3O2S3 superconductors. From electrical resistivity measurements, the Tc,zero of the optimally Y-doped Bi3O2S3 was higher than that of pure Bi3O2S3. This Y content dependence of the superconducting properties in Bi3O2S3 is explained by the chemical pressure effect.

  2. Randomized clinical trial comparing fixed-time split dosing and split dosing of oral Picosulfate regimen for bowel preparation.

    Science.gov (United States)

    Jun, Jae Hyuck; Han, Koon Hee; Park, Jong Kyu; Seo, Hyun Il; Kim, Young Don; Lee, Sang Jin; Jun, Baek Gyu; Hwang, Min Sik; Park, Yoon Kyoo; Kim, Myeong Jong; Cheon, Gab Jin

    2017-08-28

    To compare the efficacy of fixed-time split dose and split dose of an oral sodium picosulfate for bowel preparation. This is study was prospective, randomized controlled study performed at a single Institution (2013-058). A total of 204 subjects were assigned to receive one of two sodium picosulfate regimens ( i.e ., fixed-time split or split) prior to colonoscopy. Main outcome measurements were bowel preparation quality and subject tolerability. There was no statistical difference between the fixed-time split dose regimen group and the split dose regimen group (Ottawa score mean 2.57 ± 1.91 vs 2.80 ± 2.51, P = 0.457). Cecal intubation time and physician's satisfaction of inspection were not significantly different between the two groups ( P = 0.428, P = 0.489). On subgroup analysis, for afternoon procedures, the fixed-time split dose regimen was equally effective as compared with the split dose regimen (Ottawa score mean 2.56 ± 1.78 vs 2.59 ± 2.27, P = 0.932). There was no difference in tolerability or compliance between the two groups. Nausea was 21.2% in the fixed-time split dose group and 14.3% in the split dose group ( P = 0.136). Vomiting was 7.1% and 2.9% ( P = 0.164), abdominal discomfort 7.1% and 4.8% ( P = 0.484), dizziness 1% and 4.8% ( P = 0.113), cold sweating 1% and 0% ( P = 0.302) and palpitation 0% and 1% ( P = 0.330), respectively. Sleep disturbance was two (2%) patients in the fixed-time split dose group and zero (0%) patient in the split dose preparation ( P = 0.143) group. A fixed-time split dose regimen with sodium picosulfate is not inferior to a split dose regimen for bowel preparation and equally effective for afternoon colonoscopy.

  3. Optically detecting spin-split bands in semiconductors in magnetic fields

    Science.gov (United States)

    Pan, X.; Sun, Y.; Saha, D.; Sanders, G. D.; Santos, M. B.; Doezema, R. E.; Hayes, S.; Khodaparast, G.; Munekata, H.; Matsuda, Y. H.; Kono, J.; Stanton, C. J.

    2012-10-01

    We report on combined theoretical and experimental studies of spin-split bands in semiconductors in magnetic fields. We have studied a wide range of systems including: 1) electron and valence band splitting in dilute magnetically doped semiconductors (DMS) systems like InMnAs, 2) electron and valence band splitting in strained InSb/AlInSb heterostructures and 3) valence band splitting in GaAs. The systems have been studied with a variety of experimental techniques including: i) ultra-high magnetic field cyclotron resonance ii) magnetoabsorption and iii) optically pumped NMR (OPNMR). Calculations are based on the 8-band Pidgeon-Brown model generalized to include the effects of the quantum confinement potential as well as pseudomorphic strain at the interfaces and sp-d coupling between magnetic impurities and conduction band electrons and valence band holes. Optical properties are calculated within the golden rule approximation and compared with experiments. Detailed comparison to experiment allows one to accurately determine conduction and valence band parameters including effective masses and g-factors. Results for InMnAs show shifts in the cyclotron resonance peaks with Mn doping. For InSb, we find a sensitive dependence of the elecronic structure on the strain at the pseudomorphic interfaces. For GaAs, we show that OPNMR allows us to spin-resolve the valence bands and that structure in the OPNMR signal is dominated by the weaker light hole to conduction band Landau level transitions.

  4. Room temperature synthesis of crystalline Sb2S3 for SnO2 ...

    Indian Academy of Sciences (India)

    The photoluminescence analysis shows low green luminescence as well as Stoke's shift for as-prepared Sb2S3. The nanostructured solar cell is fabricated for energy harvesting purpose with Sb2S3-sensitized SnO2 photoanode and polysulphide electrolyte. The solar cell with. FTO/SnO2/Sb2S3 photoanode shows VOC ...

  5. The Regularity of Functions on Dual Split Quaternions in Clifford Analysis

    Directory of Open Access Journals (Sweden)

    Ji Eun Kim

    2014-01-01

    Full Text Available This paper shows some properties of dual split quaternion numbers and expressions of power series in dual split quaternions and provides differential operators in dual split quaternions and a dual split regular function on Ω⊂ℂ2×ℂ2 that has a dual split Cauchy-Riemann system in dual split quaternions.

  6. Splitting of the weak hypercharge quantum

    International Nuclear Information System (INIS)

    Nielsen, H.B.; Brene, N.

    1990-12-01

    The ratio between the weak hypercharge quantum for particles having no coupling to the gauge bosons corresponding to the semisimple component of the gauge group and the smallest hypercharge quantum for particles that do have such couplings is exceptionally large for the standard model, considering its rank. To compare groups with respect to this property we propose a quantity χ which depends on the rank of the group and the splitting ratio of the hypercharge(s) to be found in the group. The quantity χ has maximal value for the gauge group of the standard model. This suggest that the hypercharge splitting may play an important role either in the origin of the gauge symmetry at a fundamental scale or in some kind of selection mechanism at a scale perhaps nearer to the experimental scale. Such selection mechanism might be what we have called confusion which removes groups with many (so called generalized) automorphisms. The quantity χ tends to be large for groups with few generalized automorphisms. (orig.)

  7. Strong CP, flavor, and twisted split fermions

    International Nuclear Information System (INIS)

    Harnik, Roni; Perez, Gilad; Schwartz, Matthew D.; Shirman, Yuri

    2005-01-01

    We present a natural solution to the strong CP problem in the context of split fermions. By assuming CP is spontaneously broken in the bulk, a weak CKM phase is created in the standard model due to a twisting in flavor space of the bulk fermion wavefunctions. But the strong CP phase remains zero, being essentially protected by parity in the bulk and CP on the branes. As always in models of spontaneous CP breaking, radiative corrections to theta bar from the standard model are tiny, but even higher dimension operators are not that dangerous. The twisting phenomenon was recently shown to be generic, and not to interfere with the way that split fermions naturally weaves small numbers into the standard model. It follows that out approach to strong CP is compatible with flavor, and we sketch a comprehensive model. We also look at deconstructed version of this setup which provides a viable 4D model of spontaneous CP breaking which is not in the Nelson-Barr class. (author)

  8. An Iterative Algorithm for the Split Equality and Multiple-Sets Split Equality Problem

    Directory of Open Access Journals (Sweden)

    Luoyi Shi

    2014-01-01

    Full Text Available The multiple-sets split equality problem (MSSEP requires finding a point x∈∩i=1NCi, y∈∩j=1MQj such that Ax=By, where N and M are positive integers, {C1,C2,…,CN} and {Q1,Q2,…,QM} are closed convex subsets of Hilbert spaces H1, H2, respectively, and A:H1→H3, B:H2→H3 are two bounded linear operators. When N=M=1, the MSSEP is called the split equality problem (SEP. If  B=I, then the MSSEP and SEP reduce to the well-known multiple-sets split feasibility problem (MSSFP and split feasibility problem (SFP, respectively. One of the purposes of this paper is to introduce an iterative algorithm to solve the SEP and MSSEP in the framework of infinite-dimensional Hilbert spaces under some more mild conditions for the iterative coefficient.

  9. Preparation of In2S3 nanopraricle by ultrasonic dispersion and its tribology property.

    Science.gov (United States)

    Li, Zhiwei; Tao, Xiaojun; Wu, Zhishen; Zhang, Pingyu; Zhang, Zhijun

    2009-02-01

    In this paper, we describe a facile and rapid method for preparing In2S3 nanoparticles via ultrasound dispersion. This method allows us to prepare In2S3 nanoparticles from bulk indium and sulfur with ease and without using expensive agents and in a short time. The possible growing mechanism of the In2S3 nanoparticles was presented. In addition, we provide detailed characterizations including TEM, XRD, TG-DTA, and XPS to study the shape, composition and structure of In2S3 nanoparticles. We also studied the tribology property of In2S3 nanoparticles made using this novel recipe.

  10. Fabrication and characterization of a nanostructured TiO2/In2S3-Sb2S3/CuSCN extremely thin absorber (eta) solar cell

    Science.gov (United States)

    Huerta-Flores, Alí M.; García-Gómez, Nora A.; de la Parra-Arciniega, Salomé M.; Sánchez, Eduardo M.

    2016-08-01

    In this work we report the successful assembly and characterization of a TiO2/In2S3-Sb2S3/CuSCN extremely thin absorber solar cell. Nanostructured TiO2 deposited by screen printing on an ITO substrate was used as an n-type electrode. An ∼80 nm extremely thin layer of the system In2S3-Sb2S3 deposited by successive ionic layer adsorption and a reaction (silar) method was used as an absorber. The voids were filled with p-type CuSCN and the entire assembly was completed with a gold contact. The solar cell fabricated with this heterostructure showed an energy conversion efficiency of 4.9%, which is a promising result in the development of low cost and simple fabrication of solar cells.

  11. Band alignment at the Cu2SnS3/In2S3 interface measured by X-ray photoemission spectroscopy

    Science.gov (United States)

    Jia, Hongjie; Cheng, Shuying; Zhang, Hong; Yu, Jinling; Lai, Yunfeng

    2015-10-01

    This paper focused on investigating the band alignment at the Cu2SnS3 (CTS)/In2S3 heterojunction interface by X-ray photoemission spectroscopy. An In2S3 over-layer was grown on a CTS thin film, which was grown by sulfurization of vacuum thermal evaporated Sn-Cu metallic precursors in a H2S:N2 atmosphere. The valence band offset (VBO) at the CTS/In2S3 interface was measured to be 1.27 ± 0.10 eV. The conduction band offset (CBO) was calculated from the measured VBO, giving (0.58 ± 0.10) eV. These values show that the CBO has a spike-like behavior and the interface is a 'type I'.

  12. Electrocatalytic water splitting to produce fuel hydrogen

    Science.gov (United States)

    Yuan, Hao

    Solar energy is regarded as a promising source for clean and sustainable energy. However, it is not a continuous energy source, thus certain strategies have to be developed to effectively convert and store it. Solar-driven electrocatalytic water splitting, which converts solar energy into chemical energy for storage as fuel hydrogen, can effectively mitigate the intermittence of solar radiation. Water splitting consists of two half reactions: water oxidation and hydrogen evolution. Both reactions rely on highly effective electrocatalysts. This dissertation is an account of four detailed studies on developing highly effective low-cost electrocatalysts for both reactions, and includes a preliminary attempt at system integration to build a functional photoanode for solar-driven water oxidation. For the water oxidation reaction, we have developed an electrochemical method to immobilize a cobalt-based (Co-OXO) water oxidation catalyst on a conductive surface to promote recyclability and reusability without affecting functionality. We have also developed a method to synthesize a manganese-based (MnOx) catalytic film in situ, generating a nanoscale fibrous morphology that provides steady and excellent water oxidation performance. The new method involves two series of cyclic voltammetry (CV) over different potential ranges, followed by calcination to increase crystallinity. The research has the potential to open avenues for synthesizing and optimizing other manganese-based water oxidation catalysts. For the hydrogen evolution reaction, we have developed a new electrodeposition method to synthesize Ni/Ni(OH)2 catalysts in situ on conductive surfaces. The new method involves only two cycles of CV over a single potential range. The resulting catalytic film has a morphology of packed walnut-shaped particles. It has superior catalytic activity and good stability over long periods. We have investigated the feasibility of incorporating manganese-based water oxidation catalysts

  13. Research on numerical control system based on S3C2410 and MCX314AL

    Science.gov (United States)

    Ren, Qiang; Jiang, Tingbiao

    2008-10-01

    With the rapid development of micro-computer technology, embedded system, CNC technology and integrated circuits, numerical control system with powerful functions can be realized by several high-speed CPU chips and RISC (Reduced Instruction Set Computing) chips which have small size and strong stability. In addition, the real-time operating system also makes the attainment of embedded system possible. Developing the NC system based on embedded technology can overcome some shortcomings of common PC-based CNC system, such as the waste of resources, low control precision, low frequency and low integration. This paper discusses a hardware platform of ENC (Embedded Numerical Control) system based on embedded processor chip ARM (Advanced RISC Machines)-S3C2410 and DSP (Digital Signal Processor)-MCX314AL and introduces the process of developing ENC system software. Finally write the MCX314AL's driver under the embedded Linux operating system. The embedded Linux operating system can deal with multitask well moreover satisfy the real-time and reliability of movement control. NC system has the advantages of best using resources and compact system with embedded technology. It provides a wealth of functions and superior performance with a lower cost. It can be sure that ENC is the direction of the future development.

  14. The impact of payment splitting on liquidity requirements in RTGS

    OpenAIRE

    Denbee, Edward; Norman, Ben

    2010-01-01

    This paper examines the impact that payment splitting could have upon the liquidity requirements and efficiency of a large-value payment system, such as the United Kingdom’s CHAPS. Using the Bank of Finland Payment and Settlement Simulator and real UK payments data we find that payment splitting could reduce the liquidity required to settle payments. The reduction in required liquidity would increase as the payment splitting threshold decreased but the relationship is non-linear. Liquidity sa...

  15. Splitting methods in communication, imaging, science, and engineering

    CERN Document Server

    Osher, Stanley; Yin, Wotao

    2016-01-01

    This book is about computational methods based on operator splitting. It consists of twenty-three chapters written by recognized splitting method contributors and practitioners, and covers a vast spectrum of topics and application areas, including computational mechanics, computational physics, image processing, wireless communication, nonlinear optics, and finance. Therefore, the book presents very versatile aspects of splitting methods and their applications, motivating the cross-fertilization of ideas. .

  16. Digital gene expression analysis of corky split vein caused by boron deficiency in 'Newhall' Navel Orange (Citrus sinensis Osbeck for selecting differentially expressed genes related to vascular hypertrophy.

    Directory of Open Access Journals (Sweden)

    Cheng-Quan Yang

    Full Text Available Corky split vein caused by boron (B deficiency in 'Newhall' Navel Orange was studied in the present research. The boron-deficient citrus exhibited a symptom of corky split vein in mature leaves. Morphologic and anatomical surveys at four representative phases of corky split veins showed that the symptom was the result of vascular hypertrophy. Digital gene expression (DGE analysis was performed based on the Illumina HiSeq™ 2000 platform, which was applied to analyze the gene expression profilings of corky split veins at four morphologic phases. Over 5.3 million clean reads per library were successfully mapped to the reference database and more than 22897 mapped genes per library were simultaneously obtained. Analysis of the differentially expressed genes (DEGs revealed that the expressions of genes associated with cytokinin signal transduction, cell division, vascular development, lignin biosynthesis and photosynthesis in corky split veins were all affected. The expressions of WOL and ARR12 involved in the cytokinin signal transduction pathway were up-regulated at 1(st phase of corky split vein development. Furthermore, the expressions of some cell cycle genes, CYCs and CDKB, and vascular development genes, WOX4 and VND7, were up-regulated at the following 2(nd and 3(rd phases. These findings indicated that the cytokinin signal transduction pathway may play a role in initiating symptom observed in our study.

  17. Diastereoselective Synthesis of 1-Deoxygalactonojirimycin, 1-Deoxyaltronojirimycin, and N-Boc-(2S,3S)-3-Hydroxypipecolic Acid via Proline Catalyzed α-Aminoxylation of Aldehydes.

    Science.gov (United States)

    Chacko, Shibin; Ramapanicker, Ramesh

    2015-05-01

    An efficient synthesis of deoxygalactonojirimycin and deoxyaltronojirimycin through the use of proline catalyzed asymmetric α-aminoxylation of a higher homologue of Garner's aldehyde, derived from l-aspartic acid, is reported. The method is also used for a highly diastereoselective synthesis of the N-Boc derivative of (2S,3S)-3-hydroxypipecolic acid. The configuration of the proline catalyst used for the asymmetric aminoxylation step ultimately controls the absolute configuration of three adjacent stereogenic centers in the final products.

  18. A Power System Network Splitting Strategy Based on Contingency Analysis

    Directory of Open Access Journals (Sweden)

    Nur Zawani Saharuddin

    2018-02-01

    Full Text Available This paper proposes a network splitting strategy following critical line outages based on N-1 contingency analysis. Network splitting is the best option for certain critical outages when the tendency of severe cascading failures is very high. Network splitting is executed by splitting the power system network into feasible set of islands. Thus, it is essential to identify the optimal splitting solution (in terms of minimal power flow disruption that satisfies certain constraints. This paper determines the optimal splitting solution for each of the critical line outage using discrete evolutionary programming (DEP optimization technique assisted by heuristic initialization approach. Heuristic initialization provides the best initial cutsets which will guide the optimization technique to find the optimal splitting solution. Generation–load balance and transmission line overloading analysis are carried out in each island to ensure the steady state stability is achieved. Load shedding scheme is initiated if the power balance criterion is violated in any island to sustain the generation–load balance. The proposed technique is validated on the IEEE 118 bus system. Results show that the proposed approach produces an optimal splitting solution with lower power flow disruption during network splitting execution.

  19. Split-plot designs for multistage experimentation

    DEFF Research Database (Denmark)

    Kulahci, Murat; Tyssedal, John

    2016-01-01

    Most of today’s complex systems and processes involve several stages through which input or the raw material has to go before the final product is obtained. Also in many cases factors at different stages interact. Therefore, a holistic approach for experimentation that considers all stages...... on the Kronecker product representation of orthogonal designs and can be used for any number of stages, for various numbers of subplots and for different number of subplots for each stage. The procedure is demonstrated on both regular and nonregular designs and provides the maximum number of factors that can...... be accommodated in each stage. Furthermore, split-plot designs for multistage experiments with good projective properties are also provided....

  20. Auxiliary gauge mediation: a new route to mini-split supersymmetry

    Science.gov (United States)

    Kahn, Yonatan; McCullough, Matthew; Thaler, Jesse

    2013-11-01

    The discovery of a standard-model-like Higgs at 126 GeV and the absence of squark signals thus far at the LHC both point towards a mini-split spectrum for supersymmetry. Within standard paradigms, it is non-trivial to realize a mini-split spectrum with heavier sfermions but lighter gauginos while simultaneously generating Higgs sector soft terms of the correct magnitude, suggesting the need for new models of supersymmetry breaking and mediation. In this paper, we present a new approach to mini-split model building based on gauge mediation by "auxiliary groups", which are the anomaly-free continuous symmetries of the standard model in the limit of vanishing Yukawa couplings. In addition to the well-known flavor SU(3) F and baryon-minus-lepton U(1) B-L groups, we find that an additional U(1) H acting on the Higgs doublets alone can be used to generate Higgs soft masses and B-terms necessary for a complete model of mini-split. Auxiliary gauge mediation is a special case of Higgsed gauge mediation, and we review the resulting two-loop scalar soft terms as well as three-loop gaugino masses. Along the way, we present a complete two-loop calculation of A-terms and B-terms in gauge mediation, which — contrary to a common misconception — includes a non-zero contribution at the messenger threshold which can be sizable in models with light gauginos. We present several phenomenologically acceptable mini-split spectra arising from auxiliary gauge mediation and highlight a complete minimal model which realizes the required spectrum and Higgs sector soft terms with a single U(1) X auxiliary gauge symmetry. We discuss possible experimental consequences.

  1. Molecular concepts of water splitting. Nature's approach

    International Nuclear Information System (INIS)

    Cox, Nicholas; Lubitz, Wolfgang

    2013-01-01

    Based on studies of natural systems, much has also been learned concerning the design principles required for biomimetic catalysis of water splitting and hydrogen evolution. In summary, these include use of abundant and inexpensive metals, the effective protection of the active sites in functional environments, repair/replacement of active components in case of damage, and the optimization of reaction rates. Biomimetic chemistry aims to mimic all these features; many labs are working toward this goal by developing new approaches in the design and synthesis of such systems, encompassing not only the catalytic center, but also smart matrices and assembly via self-organization. More stable catalysts that do not require self-repair may be obtained from fully artificial (inorganic) catalytic systems that are totally different from the biological ones and only apply some basic principles learned from nature. Metals other than Mn/Ca, Fe, and Ni could be used (e.g. Co) in new ligand spheres and other matrices. For light harvesting, charge separation/stabilization, and the effective coupling of the oxidizing/reducing equivalents to the redox catalysts, different methods have been proposed - for example, covalently linked molecular donor-acceptor systems, photo-voltaic devices, semiconductor-based systems, and photoactive metal complexes. The aim of all these approaches is to develop catalytic systems that split water with sunlight into hydrogen and oxygen while displaying high efficiency and long-term stability. Such a system - either biological, biomimetic, or bioinspired - has the potential to be used on a large scale to produce 'solar fuels' (e.g. hydrogen or secondary products thereof). (orig.)

  2. Highly reproducible planar Sb2S3-sensitized solar cells based on atomic layer deposition

    Science.gov (United States)

    KimThese Two Authors Have Equally Contributed To This Work., Dae-Hwan; Lee, Sang-Ju; Park, Mi Sun; Kang, Jin-Kyu; Heo, Jin Hyuck; Im, Sang Hyuk; Sung, Shi-Joon

    2014-11-01

    A high-quality Sb2S3 thin-absorber with controllable thickness was reproducibly formed by atomic layer deposition (ALD) technique. Compared with conventional chemical bath deposition (CBD), the Sb2S3 absorber deposited by ALD did not contain oxide or oxygen impurities and showed a very uniform thickness of Sb2S3 absorbers formed on a rough surface of dense blocking TiO2/F-doped SnO2 (bl-TiO2/FTO) substrate. The planar ALD-Sb2S3 solar cells comprised of Au/Poly-3-hexylthiophene/ALD-Sb2S3/bl-TiO2/FTO showed significantly improved power conversion efficiency of 5.77% at 1 sun condition and narrow efficiency deviation, whereas the planar CBD-Sb2S3 solar cells exhibited 2.17% power conversion efficiency. The high efficiency and good reproducibility of ALD-Sb2S3 solar cell devices is attributed to reduced backward recombination because of the inhibition of oxide defects within ALD-Sb2S3 absorber and the conformal deposition of very uniform Sb2S3 absorbers on the blocking TiO2 surface by ALD process.A high-quality Sb2S3 thin-absorber with controllable thickness was reproducibly formed by atomic layer deposition (ALD) technique. Compared with conventional chemical bath deposition (CBD), the Sb2S3 absorber deposited by ALD did not contain oxide or oxygen impurities and showed a very uniform thickness of Sb2S3 absorbers formed on a rough surface of dense blocking TiO2/F-doped SnO2 (bl-TiO2/FTO) substrate. The planar ALD-Sb2S3 solar cells comprised of Au/Poly-3-hexylthiophene/ALD-Sb2S3/bl-TiO2/FTO showed significantly improved power conversion efficiency of 5.77% at 1 sun condition and narrow efficiency deviation, whereas the planar CBD-Sb2S3 solar cells exhibited 2.17% power conversion efficiency. The high efficiency and good reproducibility of ALD-Sb2S3 solar cell devices is attributed to reduced backward recombination because of the inhibition of oxide defects within ALD-Sb2S3 absorber and the conformal deposition of very uniform Sb2S3 absorbers on the blocking TiO2

  3. Synthesis, characterization and photovoltaic properties of Mn-doped Sb2S3 thin film

    Directory of Open Access Journals (Sweden)

    Horoz Sabit

    2018-03-01

    Full Text Available Synthesis and characterization of Mn-doped Sb2S3 thin films (TFs prepared by chemical bath deposition (CBD at room temperature have been documented and their structural, optical, morphological, magnetic and photovoltaic properties have been examined for the first time. Their structural properties reveal that the Mn-doped Sb2S3 TF has an orthorhombic phase structure of Sb2S3, and that the grain size of the Mn-doped Sb2S3 TF (72.9 nm becomes larger than that of undoped Sb2S3 TF (69.3 nm. It has been observed that Mn content causes the Sb2S3 TF band gap to decrease. This situation clearly correlates with band tailing due to the impurities that are involved. The morphological properties have revealed that the shape of the Mn-doped Sb2S3 TF is more uniform than the shape of its undoped counterpart. The study on its magnetic properties has demonstrated that the Mn-doped Sb2S3 TF exhibits paramagnetic behavior. Its paramagnetic Curie-Weiss temperature was found to be -4.1 K. This result suggests that there is an anti-ferromagnetic interaction between Mn moments in the Mn-doped Sb2S3 TF. Incident photon to electron conversion efficiency (IPCE and J-V measurements were also carried out for the Mn-doped Sb2S3 TF for the first time. The results have indicated that the Mn-doped Sb2S3 TF can be utilized as a sensitizer to improve the performance of solar cells. Another important observation on the photovoltaic properties of Mn-doped Sb2S3 TF is that the spectral response range is wider than that of undoped Sb2S3 TF. Our study suggests that the introduction of dopant could serve as an effective means of improving the device performance of solar cells.

  4. Split-Doa10: a naturally split polytopic eukaryotic membrane protein generated by fission of a nuclear gene.

    Directory of Open Access Journals (Sweden)

    Elisabeth Stuerner

    Full Text Available Large polytopic membrane proteins often derive from duplication and fusion of genes for smaller proteins. The reverse process, splitting of a membrane protein by gene fission, is rare and has been studied mainly with artificially split proteins. Fragments of a split membrane protein may associate and reconstitute the function of the larger protein. Most examples of naturally split membrane proteins are from bacteria or eukaryotic organelles, and their exact history is usually poorly understood. Here, we describe a nuclear-encoded split membrane protein, split-Doa10, in the yeast Kluyveromyces lactis. In most species, Doa10 is encoded as a single polypeptide with 12-16 transmembrane helices (TMs, but split-KlDoa10 is encoded as two fragments, with the split occurring between TM2 and TM3. The two fragments assemble into an active ubiquitin-protein ligase. The K. lactis DOA10 locus has two ORFs separated by a 508-bp intervening sequence (IVS. A promoter within the IVS drives expression of the C-terminal KlDoa10 fragment. At least four additional Kluyveromyces species contain an IVS in the DOA10 locus, in contrast to even closely related genera, allowing dating of the fission event to the base of the genus. The upstream Kluyveromyces Doa10 fragment with its N-terminal RING-CH and two TMs resembles many metazoan MARCH (Membrane-Associated RING-CH and related viral RING-CH proteins, suggesting that gene splitting may have contributed to MARCH enzyme diversification. Split-Doa10 is the first unequivocal case of a split membrane protein where fission occurred in a nuclear-encoded gene. Such a split may allow divergent functions for the individual protein segments.

  5. Infrared Peak Splitting from Phonon Localization in Solid Hydrogen.

    Science.gov (United States)

    Magdău, Ioan B; Ackland, Graeme J

    2017-04-07

    We show that the isotope effect leads to a completely different spectroscopic signal in hydrogen-deuterium mixtures, compared to pure elements that have the same crystal structure. This is particularly true for molecular vibrations, which are the main source of information about the structure of high-pressure hydrogen. Mass disorder breaks translational symmetry, meaning that vibrations are localized almost to single molecules, and are not zone-center phonons. In mixtures, each observable infrared (IR) peak corresponds to a collection of many such molecular vibrations, which have a distribution of frequencies depending on local environment. Furthermore discrete groups of environments cause the peaks to split. We illustrate this issue by considering the IR spectrum of the high-pressure phase III structure of hydrogen, recently interpreted as showing novel phases in isotopic mixtures. We calculate the IR spectrum of hydrogen-deuterium mixtures in the C2/c and Cmca-12 structures, showing that isotopic disorder gives rise to mode localization of the high-frequency vibrons. The local coordination of the molecules leads to discrete IR peaks. The spread of frequencies is strongly enhanced with pressure, such that more peaks become resolvable at higher pressures, in agreement with the recent measurements.

  6. MR fingerprinting using the quick echo splitting NMR imaging technique.

    Science.gov (United States)

    Jiang, Yun; Ma, Dan; Jerecic, Renate; Duerk, Jeffrey; Seiberlich, Nicole; Gulani, Vikas; Griswold, Mark A

    2017-03-01

    The purpose of the study is to develop a quantitative method for the relaxation properties with a reduced radio frequency (RF) power deposition by combining magnetic resonance fingerprinting (MRF) technique with quick echo splitting NMR imaging technique (QUEST). A QUEST-based MRF sequence was implemented to acquire high-order echoes by increasing the gaps between RF pulses. Bloch simulations were used to calculate a dictionary containing the range of physically plausible signal evolutions using a range of T 1 and T 2 values based on the pulse sequence. MRF-QUEST was evaluated by comparing to the results of spin-echo methods. The specific absorption rate (SAR) of MRF-QUEST was compared with the clinically available methods. MRF-QUEST quantifies the relaxation properties with good accuracy at the estimated head SAR of 0.03 W/kg. T 1 and T 2 values estimated by MRF-QUEST are in good agreement with the traditional methods. The combination of the MRF and the QUEST provides an accurate quantification of T 1 and T 2 simultaneously with reduced RF power deposition. The resulting lower SAR may provide a new acquisition strategy for MRF when RF energy deposition is problematic. Magn Reson Med 77:979-988, 2017. © 2016 International Society for Magnetic Resonance in Medicine. © 2016 International Society for Magnetic Resonance in Medicine.

  7. Effect of threshold quantization in opportunistic splitting algorithm

    KAUST Repository

    Nam, Haewoon

    2011-12-01

    This paper discusses algorithms to find the optimal threshold and also investigates the impact of threshold quantization on the scheduling outage performance of the opportunistic splitting scheduling algorithm. Since this algorithm aims at finding the user with the highest channel quality within the minimal number of mini-slots by adjusting the threshold every mini-slot, optimizing the threshold is of paramount importance. Hence, in this paper we first discuss how to compute the optimal threshold along with two tight approximations for the optimal threshold. Closed-form expressions are provided for those approximations for simple calculations. Then, we consider linear quantization of the threshold to take the limited number of bits for signaling messages in practical systems into consideration. Due to the limited granularity for the quantized threshold value, an irreducible scheduling outage floor is observed. The numerical results show that the two approximations offer lower scheduling outage probability floors compared to the conventional algorithm when the threshold is quantized. © 2006 IEEE.

  8. Surface modifications of chalcopyrite CuInS2 thin films for photochatodes in photoelectrochemical water splitting under sunlight irradiation

    Science.gov (United States)

    Gunawan; Haris, A.; Widiyandari, H.; Septina, W.; Ikeda, S.

    2017-02-01

    Copper chalcopyrite semiconductors include a wide range of compounds that are of interest for photoelectrochemical water splitting which enables them to be used as photochatodes for H2 generation. Among them, CuInS2 is one of the most important materials due to its optimum band gap energy for sunlight absorption. In the present study, we investigated the application of CuInS2 fabricated by electrodeposition as photochatodes for water splitting. Thin film of CuInS2 chalcopyrite was formed on Mo-coated glass substrate by stacked electrodeposition of copper and indium followed by sulfurization under H2S flow. The films worked as a H2 liberation electrode under cathodic polarization from a solution containing Na2SO4 after loading Pt deposits on the film. Introduction of an n-type CdS layer by chemical bath deposition on the CuInS2 surface before the Pt loading resulted appreciable improvements of H2 liberation efficiency and a higher photocurrent onset potential. Moreover, the use of In2S3 layer as an alternative n-type layer to the CdS significantly improved the H2 liberation performance: the CuInS2 film modified with In2S3 and Pt deposits worked as an efficient photocathode for photoelectrochemical water splitting.

  9. Digital signal processing for NDT

    International Nuclear Information System (INIS)

    Georgel, B.

    1994-01-01

    NDT begins to adapt and use the most recent developments of digital signal and image processing. We briefly sum up the main characteristics of NDT situations (particularly noise and inverse problem formulation) and comment on techniques already used or just emerging (SAFT, split spectrum, adaptive learning network, noise reference filtering, stochastic models, neural networks). This survey is focused on ultrasonics, eddy currents and X-ray radiography. The final objective of end users (availability of automatic diagnosis systems) cannot be achieved only by signal processing algorithms. A close cooperation with other techniques such as artificial intelligence has therefore to be implemented. (author). 20 refs

  10. Tests of a High Temperature Sample Conditioner for the Waste Treatment Plant LV-S2, LV-S3, HV-S3A and HV-S3B Exhaust Systems

    Energy Technology Data Exchange (ETDEWEB)

    Flaherty, Julia E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Glissmeyer, John A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-03-18

    Tests were performed to evaluate a sample conditioning unit for stack monitoring at Hanford Tank Waste Treatment and Immobilization Plant (WTP) exhaust stacks with elevated air temperatures. The LV-S2, LV-S3, HV-S3A and HV-S3B exhaust stacks are expected to have elevated air temperature and dew point. At these emission points, exhaust temperatures are too high to deliver the air sample directly to the required stack monitoring equipment. As a result, a sample conditioning system is considered to cool and dry the air prior to its delivery to the stack monitoring system. The method proposed for the sample conditioning is a dilution system that will introduce cooler, dry air to the air sample stream. This method of sample conditioning is meant to reduce the sample temperature while avoiding condensation of moisture in the sample stream. An additional constraint is that the ANSI/HPS N13.1-1999 standard states that at least 50% of the 10 μm aerodynamic diameter (AD) particles present in the stack free stream must be delivered to the sample collector. In other words, depositional loss of particles should be limited to 50% in the sampling, transport, and conditioning systems. Based on estimates of particle penetration through the LV-S3 sampling system, the diluter should perform with about 80% penetration or better to ensure that the total sampling system passes the 50% or greater penetration criterion.

  11. Excitation dependent multicolor emission and photoconductivity of Mn, Cu doped In2S3 monodisperse quantum dots

    Science.gov (United States)

    Ghosh, Sirshendu; Saha, Manas; Ashok, Vishal Dev; Chatterjee, Arijit; De, S. K.

    2016-04-01

    Indium sulphide (In2S3) quantum dots (QDs) of average size 6 ± 2 nm and hexagonal nanoplatelets of average size 37 ± 4 nm have been synthesized from indium myristate and indium diethyl dithiocarbamate precursors respectively. The absorbance and emission band was tuned with variation of nanocrytal size from very small in the strong confinement regime to very large in the weak confinement regime. The blue emission and its shifting with size has been explained with the donor-acceptor recombination process. The 3d element doping (Mn2+ and Cu2+) is found to be effective for formation of new emission bands at higher wavelengths. The characteristic peaks of Mn2+ and Cu2+ and the modification of In3+ peaks in the x-ray photoelectric spectrum (XPS) confirm the incorporation of Mn2+ and Cu2+ into the In2S3 matrix. The simulation of the electron paramagnetic resonance signal indicates the coexistence of isotropic and axial symmetry for In and S vacancies. Moreover, the majority of Mn2+ ions and sulphur vacancies (VS ) reside on the surface of nanocrystals. The quantum confinement effect leads to an enhancement of band gap up to 3.65 eV in QDs. The formation of Mn 3d levels between conduction band edge and shallow donor states is evidenced from a systematic variation of emission spectra with the excitation wavelength. In2S3 QDs have been established as efficient sensitizers to Mn and Cu emission centers. Fast and slow components of photoluminescence (PL) decay dynamics in Mn and Cu doped QDs are interpreted in terms of surface and bulk recombination processes. Fast and stable photodetctors with high photocurrent gain are fabricated with Mn and Cu doped QDs and are found to be faster than pure In2S3. The fastest response time in Cu doped QDs is an indication of the most suitable system for photodetector devices.

  12. Sonochemistry synthesis and enhanced photocatalytic H2-production activity of nanocrystals embedded in CdS/ZnS/In2S3 microspheres.

    Science.gov (United States)

    Shen, Zaoyu; Chen, Gang; Wang, Qun; Yu, Yaoguang; Zhou, Chao; Wang, Yu

    2012-03-21

    ZnS and CdS nanocrystals with a size of 5-10 nm embedded in CdS/ZnS/In(2)S(3) microspheres have been successfully synthesized by a sonochemistry method at room temperature and normal pressure without the use of templates or surfactants. The as-prepared products have been characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), EDX line spectrum, high-angle annular dark-field imaging (HAADF), UV-visible diffuse reflectance spectra (UV-vis) and photoluminescence (PL) spectra. The reaction process in the solution under ultrasonic irradiation was investigated by gas chromatography-mass spectrometry (GC-MS). The mechanisms of phase formation and morphology control of CdS/ZnS/In(2)S(3) microspheres are proposed and discussed in detail. Furthermore, the photocatalytic activity of CdS/ZnS/In(2)S(3) for water splitting was investigated under visible-light irradiation (λ > 400 nm) and an especially high photocatalytic activity (apparent yield is 40.9% at 420 nm) was achieved in the absence of co-catalysts. This journal is © The Royal Society of Chemistry 2012

  13. Characterization of photovoltaics with In2S3 nanoflakes/p-Si heterojunction.

    Science.gov (United States)

    Hsiao, Yu-Jen; Lu, Chung-Hsin; Ji, Liang-Wen; Meen, Teen-Hang; Chen, Yan-Lung; Chi, Hsiao-Ping

    2014-01-15

    We demonstrate that heterojunction photovoltaics based on hydrothermal-grown In2S3 on p-Si were fabricated and characterized in the paper. An n-type In2S3 nanoflake-based film with unique 'cross-linked network' structure was grown on the prepared p-type silicon substrate. It was found that the bandgap energy of such In2S3 film is 2.5 eV by optical absorption spectra. This unique nanostructure significantly enhances the surface area of the In2S3 films, leading to obtain lower reflectance spectra as the thickness of In2S3 film was increased. Additionally, such a nanostructure resulted in a closer spacing between the cross-linked In2S3 nanostructures and formed more direct conduction paths for electron transportation. Thus, the short-circuit current density (Jsc) was effectively improved by using a suitable thickness of In2S3. The power conversion efficiency (PCE, η) of the AZO/In2S3/textured p-Si heterojunction solar cell with 100-nm-thick In2S3 film was 2.39%.

  14. Towards Highly Efficient Bias-Free Solar Water Splitting

    NARCIS (Netherlands)

    Abdi, F.F.

    2013-01-01

    Solar water splitting has attracted significant attention due to its potential of converting solar to chemical energy. It uses semiconductor to convert sunlight into electron-hole pairs, which then split water into hydrogen and oxygen. The hydrogen can be used as a renewable fuel, or it can serve as

  15. 77 FR 8127 - Foreign Tax Credit Splitting Events

    Science.gov (United States)

    2012-02-14

    ... Tax Credit Splitting Events AGENCY: Internal Revenue Service (IRS), Treasury. ACTION: Final and... affect taxpayers claiming foreign tax credits. The text of the temporary regulations also serves as the... that if there is a foreign tax credit splitting event with respect to a foreign income tax paid or...

  16. 77 FR 8184 - Foreign Tax Credit Splitting Events

    Science.gov (United States)

    2012-02-14

    ... Foreign Tax Credit Splitting Events AGENCY: Internal Revenue Service (IRS), Treasury. ACTION: Notice of... these proposed regulations. The regulations affect taxpayers claiming foreign tax credits. Special... of the Federal Register.] Sec. 1.909-6 Pre-2011 foreign tax credit splitting events. [The text of...

  17. Clonal differences in log end splitting in Eucalyptus grandis in ...

    African Journals Online (AJOL)

    This paper discusses the juvenile–mature correlation of log end splitting among Eucalyptus grandis clones from two trials and how differences in splitting relate to differences in wood density, pith-to-bark gradient and growth rate. Two approximately 20-year-old Eucalyptus grandis clonal trials at Bergvliet plantation were ...

  18. April / May 2006. 108 Harvesting split thickness skin in

    African Journals Online (AJOL)

    user

    Background: In the third world countries like Ethiopia the majority of Hospitals have difficulties in harvesting split thickness skin ... The grafts were well taken by the recipient areas and technically there was no danger of deep bite. Conclusion: Split ... to meet the hospital needs. Thus we need to improvise and use appropriate.

  19. Pulse splitting in nonlinear media with anisotropic dispersion properties

    DEFF Research Database (Denmark)

    Bergé, L.; Juul Rasmussen, J.; Schmidt, M.R.

    1998-01-01

    to a singularity in the transverse plane. Instead, the pulse spreads out along the direction of negative dispersion and splits up into small-scale cells, which may undergo further splitting events. The analytical results are supported by direct numerical solutions of the three dimensional cubic Schrodinger...

  20. Split-liver transplantation : An underused resource in liver transplantation

    NARCIS (Netherlands)

    Rogiers, Xavier; Sieders, Egbert

    2008-01-01

    Split-liver transplantation is an efficient tool to increase the number of liver grafts available for transplantation. More than 15 years after its introduction only the classical splitting technique has reached broad application. Consequently children are benefiting most from this possibility.

  1. Plasmonic nanoparticle-semiconductor composites for efficient solar water splitting

    NARCIS (Netherlands)

    Valenti, M.; Jonsson, M.P.; Biskos, G.; Schmidt-Ott, A.; Smith, W.A.

    2016-01-01

    Photoelectrochemical (PEC) water splitting is a promising technology that uses light absorbing semiconductors to convert solar energy directly into a chemical fuel (i.e., hydrogen). PEC water splitting has the potential to become a key technology in achieving a sustainable society, if high solar

  2. Enhanced residual mean circulation during the evolution of split type ...

    Indian Academy of Sciences (India)

    8

    keywords: split events, stratospheric sudden warming, residual mean circulation. 1 Introduction ... sudden warming. It is characterized by a rapid cooling of the polar cap tempera- ture (Kuroda, 2008). The competition between planetary waves and gravity waves to the residual .... any automated scheme. The split events ...

  3. Recent developments in solar H 2 generation from water splitting

    Indian Academy of Sciences (India)

    Assistance of metal nanostructures and quantum dots to semiconductors attains vital importance as they are exuberant visible light harvesters and charge carrier amplifiers. Benevolent use of quantum dots in solar water splitting and photoelectrochemical water splitting provides scope to revolutionize the quantum efficiency ...

  4. 7 CFR 51.2753 - U.S. Virginia Splits.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false U.S. Virginia Splits. 51.2753 Section 51.2753... STANDARDS) United States Standards for Shelled Virginia Type Peanuts Grades § 51.2753 U.S. Virginia Splits. “U.S. Virginia Splits” consists of shelled Virginia type peanut kernels of similar varietal...

  5. Linear expansion of products out of thermal splitting graphite

    International Nuclear Information System (INIS)

    Tishina, E.A.; Kurnevich, G.I.

    1994-01-01

    Linear expansion of thermally split graphite in the form of foil and pressed items of different density was studied. It is ascertained that the extreme character of temperature dependence of linear expansion factor of pressed samples of thermally split graphite is determined by the formation of closed pores containing air in the course of their production. 3 refs., 2 figs

  6. Evaluation of Certain Pharmaceutical Quality Attributes of Lisinopril Split Tablets

    Directory of Open Access Journals (Sweden)

    Khairi M. S. Fahelelbom

    2016-10-01

    Full Text Available Tablet splitting is an accepted practice for the administration of drugs for a variety of reasons, including dose adjustment, ease of swallowing and cost savings. The purpose of this study was to evaluate the physical properties of lisinopril tablets as a result of splitting the tablets either by hand or with a splitting device. The impact of the splitting technique of lisinopril (Zestril® tablets, 20 mg on certain physical parameters such as weight variation, friability, disintegration, dissolution and drug content were studied. Splitting the tablets either by hand or with a splitter resulted in a minute but statistically significant average weight loss of <0.25% of the tablet to the surrounding environment. The variability in the weight of the hand-split tablet halves was more pronounced (37 out of 40 tablet halves varied by more than 10% from the mean weight than when using the tablet splitter (3 out of 40 tablet halves. The dissolution and drug content of the hand-split tablets were therefore affected because of weight differences. However, the pharmacopoeia requirements for friability and disintegration time were met. Hand splitting of tablets can result in an inaccurate dose and may present clinical safety issues, especially for drugs with a narrow therapeutic window in which large fluctuations in drug concentrations are undesirable. It is recommended to use tablets with the exact desired dose, but if this is not an option, then a tablet splitter could be used.

  7. Photocatalytic Water-Splitting Reaction from Catalytic and Kinetic Perspectives

    KAUST Repository

    Hisatomi, Takashi

    2014-10-16

    Abstract: Some particulate semiconductors loaded with nanoparticulate catalysts exhibit photocatalytic activity for the water-splitting reaction. The photocatalysis is distinct from the thermal catalysis because photocatalysis involves photophysical processes in particulate semiconductors. This review article presents a brief introduction to photocatalysis, followed by kinetic aspects of the photocatalytic water-splitting reaction.Graphical Abstract: [Figure not available: see fulltext.

  8. Nonlinear Fracture Mechanics and Plasticity of the Split Cylinder Test

    DEFF Research Database (Denmark)

    Olesen, John Forbes; Østergaard, Lennart; Stang, Henrik

    2006-01-01

    The split cylinder testis subjected to an analysis combining nonlinear fracture mechanics and plasticity. The fictitious crack model is applied for the analysis of splitting tensile fracture, and the Mohr-Coulomb yield criterion is adopted for modelling the compressive crushing/sliding failure. Two...... demonstrates the influence of varying geometry or constitutive properties. For a split cylinder test in load control it is shown how the ultimate load is either plasticity dominated or fracture mechanics dominated. The transition between the two modes is related to changes in geometry or constitutive...... properties. This implies that the linear elastic interpretation of the ultimate splitting force in term of the uniaxial tensile strength of the material is only valid for special situations, e.g. for very large cylinders. Furthermore, the numerical analysis suggests that the split cylinder test is not well...

  9. Optimizing TCP Performance over UMTS with Split TCP Proxy

    DEFF Research Database (Denmark)

    Hu, Liang; Dittmann, Lars

    2009-01-01

    . To cope with large delay bandwidth product, we propose a novel concept of split TCP proxy which is placed at GGSN between UNITS network and Internet. The split proxy divides the bandwidth delay product into two parts, resulting in two TCP connections with smaller bandwidth delay products which can...... be pipelined and thus operating at higher speeds. Simulation results show, the split TCP proxy can significantly improve the TCP performance in terms of RLC throughput under high bit rate DCH channel scenario (e.g.256 kbps). On the other hand, it only brings small performance improvement under low bit rate DCH...... scenario (e.g.64 kbps). Besides, the split TCP proxy brings more performance gain for downloading large files than downloading small ones. To the end, for the configuration of the split proxy, an aggressive initial TCP congestion window size (e.g. 10 MSS) at proxy is particularly useful for radio links...

  10. Photoelectrochemical solar water splitting: From basic principles to advanced devices

    Directory of Open Access Journals (Sweden)

    Bandar Y.Alfaifi

    2018-02-01

    Full Text Available Photoelectrochemical water splitting (PEC offers a promising path for sustainable generation of hydrogen fuel. However, improving solar fuel water splitting efficiency facing tremendous challenges, due to the energy loss related to fast recombination of the photogenerated charge carriers, electrode degradation, as well as limited light harvesting. This review focuses on the brief introduction of basic fundamental of PEC water splitting and the concept of various types of water splitting approaches. Numerous engineering strategies for the investgating of the higher efficiency of the PEC, including charge separation, light harvesting, and co-catalysts doping, have been discussed. Moreover, recent remarkable progress and developments for PEC water splitting with some promising materials are discussed. Recent advanced applications of PEC are also reviewed. Finally, the review concludes with a summary and future outlook of this hot field.

  11. Retrograde signaling

    DEFF Research Database (Denmark)

    Kleine, Tatjana; Leister, Dario Michael

    2016-01-01

    The term retrograde signaling refers to the fact that chloroplasts and mitochondria utilize specific signaling molecules to convey information on their developmental and physiological states to the nucleus and modulate the expression of nuclear genes accordingly. Signals emanating from plastids...... of retrograde signaling has since been extended and revised. Elements of several 'operational' signaling circuits have come to light, including metabolites, signaling cascades in the cytosol and transcription factors. Here, we review recent advances in the identification and characterization of retrograde...

  12. Field-Split Preconditioned Inexact Newton Algorithms

    KAUST Repository

    Liu, Lulu

    2015-06-02

    The multiplicative Schwarz preconditioned inexact Newton (MSPIN) algorithm is presented as a complement to additive Schwarz preconditioned inexact Newton (ASPIN). At an algebraic level, ASPIN and MSPIN are variants of the same strategy to improve the convergence of systems with unbalanced nonlinearities; however, they have natural complementarity in practice. MSPIN is naturally based on partitioning of degrees of freedom in a nonlinear PDE system by field type rather than by subdomain, where a modest factor of concurrency can be sacrificed for physically motivated convergence robustness. ASPIN, originally introduced for decompositions into subdomains, is natural for high concurrency and reduction of global synchronization. We consider both types of inexact Newton algorithms in the field-split context, and we augment the classical convergence theory of ASPIN for the multiplicative case. Numerical experiments show that MSPIN can be significantly more robust than Newton methods based on global linearizations, and that MSPIN can be more robust than ASPIN and maintain fast convergence even for challenging problems, such as high Reynolds number Navier--Stokes equations.

  13. Split-Field Magnet facility upgraded

    CERN Multimedia

    CERN PhotoLab

    1977-01-01

    The Split Field Magnet (SFM) was the largest spectrometer for particles from beam-beam collisions in the ISR. It could determine particle momenta in a large solid angle, but was designed mainly for the analysis of forward travelling particles.As the magnet was working on the ISR circulating beams, its magnetic field had to be such as to restore the correct proton orbit.The SFM, therefore, produced zero field at the crossing point and fields of opposite signs upstream and downstream of it and was completed by 2 large and 2 small compensator magnets. The gradient effects were corrected by magnetic channels equipped with movable flaps. The useful magnetic field volume was 28 m3, the induction in the median plane 1.14 T, the gap heigth 1.1 m, the length 10.5 m, the weight about 1000 ton. Concerning the detectors, the SFM was the first massive application of multiwire proportional chambers (about 70000 wires) which filled the main and the large compensator magnets. In 1976 an improved programme was started with tw...

  14. A method of obtaining signal components of residual carrier signal with their power content and computer simulation

    Science.gov (United States)

    Kantak, Anil V.

    1993-01-01

    A novel algorithm to obtain all signal components of a residual carrier signal with any number of channels is presented. The phase modulation type may be NRZ-L or split phase (Manchester). The algorithm also provides a simple way to obtain the power contents of the signal components. Steps to recognize the signal components that influence the carrier tracking loop and the data tracking loop at the receiver are given. A computer program for numerical computation is also provided.

  15. Synthesis, optical properties and growth process of In2S3 nanoparticles.

    Science.gov (United States)

    Ning, Jiajia; Men, Kangkang; Xiao, Guanjun; Zhao, Liyan; Wang, Li; Liu, Bingbing; Zou, Bo

    2010-07-15

    Cubic beta-In(2)S(3) nanoparticles (NPs) have been synthesized by a simple and facile way, which is 6 nm in size. Absorption and emission spectra of In(2)S(3) NPs show obvious blue peak shift compared to band gap of bulk In(2)S(3), indicating the strong quantum size confinement effect. The fluorescence quantum yield of In(2)S(3) NPs is found to be 10%. During the synthesis process, the absorption spectra have no peak shift, which is responding to transition from valence band to the conduction band levels. This absorption spectra show that the nucleation and growth process of In(2)S(3) NPs is very quick. The PL lifetime spectra and time resolved spectra give two emission processes in In(2)S(3) NPs, which would be excitonic recombination and electron-hole recombination via defects levels. The blue shift of emission peaks show the emission process in In(2)S(3) NPs is from mainly electron-holes recombination via defects levels to excitonic recombination. The Stokes shift becomes smaller which is mainly contributed by blue shift of emission and smaller contribution from the UV-Vis absorption. The absorption and emission spectra show the size and crystallinity of In(2)S(3) NPs have no changes (HRTEM images provide enough proofs); however the surface-related defects changed greatly in the reaction process. Copyright 2010 Elsevier Inc. All rights reserved.

  16. Optoelectronic characterizations of vacuum evaporated Cu 2 SnS 3 ...

    African Journals Online (AJOL)

    The structure and morphology characteristics of Cu2SnS3 ternary film were investigated by X-Ray Diffraction and Scanning Electron Microscope. Four point probe and semiconductor characterization system were used to determine the electrical properties of the deposited Cu2SnS3 ternary films. UV –Vis Spectrophotometer ...

  17. The herpes simplex virus 1 U{sub S}3 regulates phospholipid synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Wild, Peter, E-mail: pewild@access.uzh.ch [Institute of Veterinary Anatomy, University of Zuerich (Switzerland); Institute of Virology, University of Zuerich (Switzerland); Oliveira, Anna Paula de [Institute of Virology, University of Zuerich (Switzerland); Sonda, Sabrina [Institute for Parasitology, University of Zuerich (Switzerland); Schraner, Elisabeth M. [Institute of Veterinary Anatomy, University of Zuerich (Switzerland); Institute of Virology, University of Zuerich (Switzerland); Ackermann, Mathias; Tobler, Kurt [Institute of Virology, University of Zuerich (Switzerland)

    2012-10-25

    Herpes simplex virus type 1 capsids bud at nuclear and Golgi membranes for envelopment by phospholipid bilayers. In the absence of U{sub S}3, nuclear membranes form multiple folds harboring virions that suggests disturbance in membrane turnover. Therefore, we investigated phospholipid metabolism in cells infected with the U{sub S}3 deletion mutant R7041({Delta}U{sub S}3), and quantified membranes involved in viral envelopment. We report that (i) [{sup 3}H]-choline incorporation into nuclear membranes and cytoplasmic membranes was enhanced peaking at 12 or 20 h post inoculation with wild type HSV-1 and R7041({Delta}U{sub S}3), respectively, (ii) the surface area of nuclear membranes increased until 24 h of R7041({Delta}U{sub S}3) infection forming folds that equaled {approx}45% of the nuclear surface, (iii) the surface area of viral envelopes between nuclear membranes equaled {approx}2400 R7041({Delta}U{sub S}3) virions per cell, and (iv) during R7041({Delta}U{sub S}3) infection, the Golgi complex expanded dramatically. The data indicate that U{sub S}3 plays a significant role in regulation of membrane biosynthesis.

  18. Tunable surface wettability and water adhesion of Sb2S3 micro-/nanorod films

    International Nuclear Information System (INIS)

    Zhong, Xin; Zhao, Huiping; Yang, Hao; Liu, Yunling; Yan, Guoping; Chen, Rong

    2014-01-01

    Antimony sulfide (Sb 2 S 3 ) films were successfully prepared by spin coating Sb 2 S 3 micro-/nanorods with different sizes on glass slides, which was synthesized via a facile and rapid microwave irradiation method. The prepared Sb 2 S 3 micro-/nanorods and films were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM) and water contact angle (CA). The as-prepared Sb 2 S 3 films exhibited different surface wettabilities ranging from superhydrophilicity to superhydrophobicity, which was strongly dependent on the diameter of Sb 2 S 3 micro-/nanorod. Sb 2 S 3 film made by nanorods possessed superhydrophobic surface and high water adhesive property. After surface modification with stearic acid, the superhydrophobic surface exhibited an excellent self-cleaning property owing to its low adhesive force. The clarification of three possible states including Wenzel's state, “Gecko” state and Cassie's state for Sb 2 S 3 film surfaces was also proposed to provide a better understanding of interesting surface phenomena on Sb 2 S 3 films.

  19. Verification of split spectrum technique for ultrasonic inspection of welded structures in nuclear reactors

    International Nuclear Information System (INIS)

    Ericsson, L.; Stepinski, T.

    1992-01-01

    Ultrasonic nondestructive inspection of materials is often limited by the presence of backscattered echoes from the material structure. A digital signal processing technique for removal of this material noise, referred to as split spectrum processing (SSP), has been developed and verified using simple laboratory experiments during the last decade. However, application of the split spectrum processing algorithm to industrial conditions has been rarely reported. In the paper the results of the practical evaluation of the SSP technique are presented. A number of different ultrasonic transducers were used for acquiring echoes from artificial flaws as well as natural cracks. The flaws were located in test blocks employed by the Swedish Nuclear Power Companies as reference during ultrasonic inspection of nuclear reactor vessels. The acquired ultrasonic A-scan signals were processed off-line using specially developed algorithms on a personal computer (PC). The experiments show evidence that properly tuned SSP algorithms result in a considerable improvement of the signal to material noise ratio. The enhancements were similar irrespective of the features of the transducer used or the nature of the inspected flaw. The problems related to the development of self-tuning SSP algorithms for on-line processing of B-scans are discussed. (author)

  20. Upper Mantle Dynamics of Bangladesh by Splitting Analyzes of Core Refracted SKS and SKKS Waves

    Science.gov (United States)

    Tiwari, A. K.; Bhushan, K.; Eken, T.; Singh, A.

    2017-12-01

    New shear wave splitting measurements are obtained from hitherto less studied Bengal Basin using core refracted SKS and SKKS phases. Splitting parameters, time delays (δt) and fast polarization directions (Φ) were estimated through analysis of 64 high-quality waveforms (≥ 2.5 signal to noise ratio) from 29 earthquakes with magnitude ≥5.5 recorded at eight seismic stations deployed over Bangladesh. We found no evidence of splitting which indicates azimuthal isotropy beneath the region. Null measurements can be explained by near vertical axis of anisotropy or by the presence of multiple anisotropic layers with different fast polarization directions, where combined effect results in null. We consider that the presence of partial melts within the upper mantle due to Kerguelen mantle plume activities may be the potential geodynamic cause for observed null measurements. It locally perturbed mantle convection flow beneath the region and reoriented the lattice preferred orientation of the upper mantle mineral mainly olivine as this disabled the core refracted SKS and SKKS phases to scan the anisotropic characteristics of the region, and hence null measurements are obtained.

  1. Minimax robust power split in AF relays based on uncertain long-term CSI

    KAUST Repository

    Nisar, Muhammad Danish

    2011-09-01

    An optimal power control among source and relay nodes in presence of channel state information (CSI) is vital for an efficient amplify and forward (AF) based cooperative communication system. In this work, we study the optimal power split (power control) between the source and relay node in presence of an uncertainty in the CSI. The prime contribution is to solve the problem based on an uncertain long-term knowledge of both the first and second hop CSI (requiring less frequent updates), and under an aggregate network-level power constraint. We employ the minimax optimization methodology to arrive at the minimax robust optimal power split, that offers the best possible guarantee on the end-to-end signal to noise ratio (SNR). The derived closed form analytical expressions admit simple intuitive interpretations and are easy to implement in real-world AF relaying systems. Numerical results confirm the advantages of incorporating the presence of uncertainty into the optimization problem, and demonstrate the usefulness of the proposed minimax robust optimal power split. © 2011 IEEE.

  2. Dual Connectivity in LTE HetNets with Split Control- and User-Plane

    DEFF Research Database (Denmark)

    Zakrzewska, Anna; López-Pérez, David; Kucera, Stepan

    2013-01-01

    Recently, a new network architecture with split control-plane and user-plane has been proposed and gained a lot of momentum in the standardisation of Long Term Evolution (LTE) Release 12. In this new network architecture, the controlplane, which transmits system information and handles user...... a detailed description of our dual connectivity framework based on the latest LTE-Advanced enhancements, in which macrocellassisted (MA) small cells use different channel state informationreference signals (CSI-RS) to differentiate among each other and allow User Equipment (UE) to take adequate measurements...

  3. Photoswitchable Rabi Splitting in Hybrid Plasmon-Waveguide Modes.

    Science.gov (United States)

    Lin, Linhan; Wang, Mingsong; Wei, Xiaoling; Peng, Xiaolei; Xie, Chong; Zheng, Yuebing

    2016-12-14

    Rabi splitting that arises from strong plasmon-molecule coupling has attracted tremendous interests. However, it has remained elusive to integrate Rabi splitting into the hybrid plasmon-waveguide modes (HPWMs), which have advantages of both subwavelength light confinement of surface plasmons and long-range propagation of guided modes in dielectric waveguides. Herein, we explore a new type of HPWMs based on hybrid systems of Al nanodisk arrays covered by PMMA thin films that are doped with photochromic molecules and demonstrate the photoswitchable Rabi splitting with a maximum splitting energy of 572 meV in the HPWMs by controlling the photoisomerization of the molecules. Through our experimental measurements combined with finite-difference time-domain (FDTD) simulations, we reveal that the photoswitchable Rabi splitting arises from the switchable coupling between the HPWMs and molecular excitons. By harnessing the photoswitchable Rabi splitting, we develop all-optical light modulators and rewritable waveguides. The demonstration of Rabi splitting in the HPWMs will further advance scientific research and device applications of hybrid plasmon-molecule systems.

  4. Wideband metasurface filter based on complementary split-ring resonators

    Science.gov (United States)

    Zhang, Tong; Zhang, Jiameng; Xu, Jianchun; Wang, Qingmin; Zhao, Ruochen; Liu, Hao; Dong, Guoyan; Hao, Yanan; Bi, Ke

    2017-08-01

    A wideband metasurface filter based on complementary split-ring resonators (CSRR) has been prepared. The frequency and transmission bandwidth of the metasurface filters with different split widths are discussed. After analyzing the mechanism of the metasurface, the proposed metasurface filters are fabricated. The electromagnetic properties of the metasurface are measured by a designed test system. The measured results are in good agreement with the simulated ones, which shows that the metasurface filter has a wideband property. As the split width of the CSRR increases, the frequency of the passband shifts to higher frequency regions and the transmission bandwidth decreases.

  5. A splitting algorithm for directional regularization and sparsification

    DEFF Research Database (Denmark)

    Rakêt, Lars Lau; Nielsen, Mads

    2012-01-01

    We present a new split-type algorithm for the minimization of a p-harmonic energy with added data fidelity term. The half-quadratic splitting reduces the original problem to two straightforward problems, that can be minimized efficiently. The minimizers to the two sub-problems can typically...... be computed pointwise and are easily implemented on massively parallel processors. Furthermore the splitting method allows for the computation of solutions to a large number of more advanced directional regularization problems. In particular we are able to handle robust, non-convex data terms, and to define...

  6. Ridge Splitting Technique for Horizontal Augmentation and Immediate Implant Placement

    Directory of Open Access Journals (Sweden)

    Papathanasiou Ioannis

    2014-03-01

    Full Text Available Insufficient width of the alveolar ridge often prevents ideal implant placement. Guided bone regeneration, bone grafting, alveolar ridge splitting and combinations of these techniques are used for the lateral augmentation of the alveolar ridge. Ridge splitting is a minimally invasive technique indicated for alveolar ridges with adequate height, which enables immediate implant placement and eliminates morbidity and overall treatment time. The classical approach of the technique involves splitting the alveolar ridge into 2 parts with use of ostetomes and chisels. Modifications of this technique include the use of rotating instrument, screw spreaders, horizontal spreaders and ultrasonic device.

  7. Market Split based Congestion Management for Networks with Loops

    Science.gov (United States)

    Marmiroli, Marta; Tanimoto, Masahiko; Tsukamoto, Yukitoki; Yokoyama, Ryuichi

    Market splitting is one of the methods to solve the transmission congestion problem associated with the introduction of competitive electricity market and transmission access. Based on the concept of price difference among congested areas, the market splitting approach produces a solution that strongly informs market participants of congestion path. In this paper, an algorithm to solve the market splitting problem for complex networks including loop structures is proposed. The method, based on an algebraic approach, ensures a feasible optimal solution verifiable and easily understandable by the market participants. Complex networks are transformed into simple radial ones using the delta-star approach. The method was tested on large problems to evaluate the performances.

  8. In Situ Growth of In2S3 Nanorods in Poly(3-Hexylthiophene) Hybrid Films

    Science.gov (United States)

    Cota-Leal, M.; Sotelo-Lerma, M.; Corona-Corona, I.; Quevedo-Lopez, M. A.

    2016-04-01

    A novel and efficient gas-liquid method for the in situ synthesis of In2S3 nanorods in a poly(3-hexylthiophene) (P3HT) matrix is demonstrated. The method involves a self-contained reaction between Na2S and HCl that produces H2S, which reacts with a P3HT/InCl3 solution resulting in hybrid P3HT/In2S3 films. The Na2S solution is regenerated for further use. The method yielded results in In2S3 nanoparticles and nanorods in a P3HT matrix, as observed by transmission electron microscopy. The In2S3 nanorods are 3 nm wide and ~30 nm long. The size of the nanorods is dependent on the P3HT concentration. The band gap (E g) of the resulting In2S3/P3HT is in the range of 2.97-3.71 eV, as measured by UV-visible spectroscopy (UV-Vis) Charge transfer in the In2S3/P3HT was demonstrated by the presence of quenching in the fluorescence spectra of the composite. Chemical composition was investigated by energy dispersive x-ray spectroscopy analysis, as well as x-ray photoelectron spectroscopy. Both techniques demonstrated the formation of In2S3.

  9. AdS3/CFT2, finite-gap equations and massless modes

    International Nuclear Information System (INIS)

    Lloyd, Thomas; Stefański, Bogdan Jr.

    2014-01-01

    It is known that string theory on AdS 3 ×M 7 backgrounds, where M 7 =S 3 ×S 3 ×S 1 or S 3 ×T 4 , is classically integrable. This integrability has been previously used to write down a set of integral equations, known as the finite-gap equations. These equations can be solved for the closed string spectrum of the theory. However, it has been known for some time that the finite-gap equations on these AdS 3 ×M 7 backgrounds do not capture the dynamics of the massless modes of the closed string theory. In this paper we re-examine the derivation of the AdS 3 ×M 7 finite-gap system. We find that the conditions that had previously been imposed on these integral equations in order to implement the Virasoro constraints are too strict, and are in fact not required. We identify the correct implementation of the Virasoro constraints on finite-gap equations and show that this new, less restrictive condition captures the complete closed string spectrum on AdS 3 ×M 7

  10. Bearing splitting and near-surface source ranging in the direct zone of deep water

    Science.gov (United States)

    Wu, Jun-Nan; Zhou, Shi-Hong; Peng, Zhao-Hui; Zhang, Yan; Zhang, Ren-He

    2016-12-01

    Sound multipath propagation is very important for target localization and identification in different acoustical zones of deep water. In order to distinguish the multipath characteristics in deep water, the Northwest Pacific Acoustic Experiment was conducted in 2015. A low-frequency horizontal line array towed at the depth of around 150 m on a receiving ship was used to receive the noise radiated by the source ship. During this experiment, a bearing-splitting phenomenon in the direct zone was observed through conventional beamforming of the horizontal line array within the frequency band 160 Hz-360 Hz. In this paper, this phenomenon is explained based on ray theory. In principle, the received signal in the direct zone of deep water arrives from two general paths including a direct one and bottom bounced one, which vary considerably in arrival angles. The split bearings correspond to the contributions of these two paths. The bearing-splitting phenomenon is demonstrated by numerical simulations of the bearing-time records and experimental results, and they are well consistent with each other. Then a near-surface source ranging approach based on the arrival angles of direct path and bottom bounced path in the direct zone is presented as an application of bearing splitting and is verified by experimental results. Finally, the applicability of the proposed ranging approach for an underwater source within several hundred meters in depth in the direct zone is also analyzed and demonstrated by simulations. Project supported by the Program of One Hundred Talented People of the Chinese Academy of Sciences and the National Natural Science Foundation of China (Grant Nos. 11434012 and 41561144006).

  11. New Insight of Northern Apennines (Italy): SKS Splitting Measurements Reveal a Complex Anisotropic Structure

    Science.gov (United States)

    Salimbeni, S.; Pondrelli, S.; Margheriti, L.; Levin, V.; Park, J.; Plomerova, J.

    2006-12-01

    The multidisciplinary RETREAT project (REtreating-Trench, Extension and Accretion Tectonics) is focused on the development of a 3D self-consistent dynamic model of the syn-convergent extension in the Northern Apennines. The seismological deployment of the Project started on 2003 and closed on September 2006, using 10 instruments lent by the GFU and 25 instruments lent by PASSCAL, added to the permanent stations of the Italian National Network. Many of the stations were deployed along a NE-SW transect across the Apennine chain. We present here new results of seismic anisotropy analysis obtained from SKS core-refracted shear waves. The study of SKS splitting is applied on twenty teleseismic earthquakes; for all of them we calculate the anisotropic parameters (delay time and fast polarization direction) by minimizing the energy in the transverse component. Our analysis assesses uncertainty by testing the parameters for stability to noise. Previous studies of splitting analysis have found in the study region evidence for tectonic domains in which a coherent splitting signal can be found. The Tuscany domain (Tyrrhenian side) shows homogeneous NW-SE fast axes directions; the Po-Plain domain (Eastern side of the Apennines) shows a N-S to NE-SW directions, here strongly influenced by backazimuth. To better define the complex structure that may exist below the Northern Apennines and Po Plain we apply the cross convolution method of Menke and Levin (2003) to discriminate whether a two-layer anisotropic model fits the splitting pattern more convincingly that a simple one-layer model. Previous analysis suggested that structure beneath the Tuscany side is simpler; a single anisotropic layer with a NW-SE fast polarization direction is in agreement with all the dataset. Beneath the Po Plain the complexity of the structure is confirmed in the analysis of most stations.

  12. Design of a Free-Ruthenium In2S3 Crystalline Photosensitized Solar Cell

    Directory of Open Access Journals (Sweden)

    Byeong Sub Kwak

    2014-01-01

    Full Text Available A new type of sulfide-based, solid-state dye material that is sensitive to visible radiation was assessed as a potential replacement for commercial ruthenium complex dyes in a dye-sensitized solar cell (DSSC assembly. The In2S3 crystals on the surface of the TiO2 bottom blocking layer were grown as a solid-state dye material. Scanning electron microscopy of In2S3 revealed a microsized, 3D-connected sheet-like shape, which was confirmed by X-ray diffraction to be a beta-structure. The efficiency of the dye-sensitized solar cells assembled with a layer grown with In2S3 increased with increasing In2S3 mole concentrations to 0.05 M (1.02% but decreased at concentrations greater than 0.6~0.8%. This suggests that crystalline In2S3 acts as a dye sensitized to visible radiation, but the short-circuit current density is too low compared to the commercially available ruthenium dye. This suggests that In2S3 crystals did not grow densely but were bulk-grown with large pores, resulting in a smaller amount of In2S3 per unit area. Two IPCE curves were observed, which were assigned to TiO2 and In2S3, meaning that the TiO2 surfaces were covered completely with In2S3 crystals. The exposure of TiO2 eventually leads to a reaction with the electrolytes, resulting in lower quantum efficiency.

  13. Sb2S3:C/CdS p-n junction by laser irradiation

    International Nuclear Information System (INIS)

    Arato, A.; Cardenas, E.; Shaji, S.; O'Brien, J.J.; Liu, J.; Castillo, G. Alan; Das Roy, T.K.; Krishnan, B.

    2009-01-01

    In this paper, we report laser irradiated carbon doping of Sb 2 S 3 thin films and formation of a p-n junction photovoltaic structure using these films. A very thin carbon layer was evaporated on to chemical bath deposited Sb 2 S 3 thin films of approximately 0.5 μm in thickness. Sb 2 S 3 thin films were prepared from a solution containing SbCl 3 and Na 2 S 2 O 3 at 27 deg. C for 5 h and the films obtained were highly resistive. These C/Sb 2 S 3 thin films were irradiated by an expanded laser beam of diameter approximately 0.5 cm (5 W power, 532 nm Verdi laser), for 2 min at ambient atmosphere. Morphology and composition of these films were analyzed. These films showed p-type conductivity due to carbon diffusion (Sb 2 S 3 :C) by the thermal energy generated by the absorption of laser radiation. In addition, these thin films were incorporated in a photovoltaic structure Ag/Sb 2 S 3 :C/CdS/ITO/Glass. For this, CdS thin film of 50 nm in thickness was deposited on a commercially available ITO coated glass substrate from a chemical bath containing CdCl 2 , sodium citrate, NH 4 OH and thiourea at 70 deg. C . On the CdS film, Sb 2 S 3 /C layers were deposited. This multilayer structure was subjected to the laser irradiation, C/Sb 2 S 3 side facing the beam. The p-n junction formed by p-Sb 2 S 3 :C and n-type CdS showed V oc = 500 mV and J sc = 0.5 mA/cm 2 under illumination by a tungsten halogen lamp. This work opens up a new method to produce solar cell structures by laser assisted material processing

  14. Performance of the split-symbol moments SNR estimator in the presence of inter-symbol interference

    Science.gov (United States)

    Shah, B.; Hinedi, S.

    1989-01-01

    The Split-Symbol Moments Estimator (SSME) is an algorithm that is designed to estimate symbol signal-to-noise ratio (SNR) in the presence of additive white Gaussian noise (AWGN). The performance of the SSME algorithm in band-limited channels is examined. The effects of the resulting inter-symbol interference (ISI) are quantified. All results obtained are in closed form and can be easily evaluated numerically for performance prediction purposes. Furthermore, they are validated through digital simulations.

  15. Identification of the transition arrays 3d74s-3d74p in Br X and 3d64s-3d64p in Br XI

    International Nuclear Information System (INIS)

    Zeng, X.T.; Jupen, C.; Bengtsson, P.; Engstroem, L.; Westerlind, M.; Martinson, I.

    1991-01-01

    We report a beam-foil study of multiply ionized bromine in the region 400-1300A, performed with 6 and 8 MeV Br ions from a tandem accelerator. At these energies transitions belonging to Fe-like Br X and Mn-like Br XI are expected to be prominent. We have identified 31 lines as 3d 7 4s-3d 7 4p transitions in Br X, from which 16 levels of the previously unknown 3d 7 4s configuration could be established. We have also added 6 new 3d 7 4p levels to the 99 previously known. For Br XI we have classified 9 lines as 3d 6 4s-3d 6 4p combinations. The line identifications have been corroborated by isoelectronic comparisons and theoretical calculations using the superposition-of-configurations technique. (orig.)

  16. Shear wave splitting in the Isparta Angle, southwestern Turkey ...

    Indian Academy of Sciences (India)

    broadband station in the Isparta Angle,southwestern Turkey.We selected 21 good quality seismic events out of nearly 357 earthquakes and calculated splitting parameters (polarization direction of fast wave, and delay time between fast and ...

  17. Field Monitoring Protocol. Mini-Split Heat Pumps

    Energy Technology Data Exchange (ETDEWEB)

    Christensen, Dane [National Renewable Energy Lab. (NREL), Golden, CO (United States); Fang, Xia [National Renewable Energy Lab. (NREL), Golden, CO (United States); Tomerlin, Jeff [National Renewable Energy Lab. (NREL), Golden, CO (United States); Winkler, Jon [National Renewable Energy Lab. (NREL), Golden, CO (United States); Hancock, E. [Mountain Energy Partnership, Longmont, CO (United States)

    2011-03-01

    This Building America program report provides a detailed method for accurately measuring and monitoring performance of a residential mini-split heat pump, which will be used in high-performance retrofit applications.

  18. Electrochemical Water-Splitting Based on Hypochlorite Oxidation

    Czech Academy of Sciences Publication Activity Database

    Minhová Macounová, Kateřina; Simic, N.; Ahlberg, E.; Krtil, Petr

    2015-01-01

    Roč. 137, č. 23 (2015), s. 7262-7265 ISSN 0002-7863 Institutional support: RVO:61388955 Keywords : electrochemistry * hypochlorite oxidation * water-splitting Subject RIV: CG - Electrochemistry Impact factor: 13.038, year: 2015

  19. Possibilities of Intermodal Passenger Transport between Split Airport and Islands

    Directory of Open Access Journals (Sweden)

    Slavko Roguljić

    2008-07-01

    Full Text Available A substantial number of passengers landing at Split Airportduring the tourist season continue their journey to the destinationson the central Dalmatian islands. Today the transfer isdone mainly through the ferry port in Split. The insufficient capacitiesof roads from the airport to the city centre which accommodatesthe ferry port and waiting for the embarkation onthe ferries and the transport itself to the islands and the finaldestinations take much longer than the air transport itself toSplit. The paper studies the possible improvements of the existingcondition as well as the construction completion and openingto traffic of the passenger sea port next to Split Airport whichwould provide a much better solution of passenger transfer tothe islands.

  20. Effect of Repeated Food Morsel Splitting on Jaw Muscle Control

    DEFF Research Database (Denmark)

    A, Kumar; Svensson, Krister G; Baad-Hansen, Lene

    2014-01-01

    Mastication is a complex motor task often initiated by splitting of the food morsel between the anterior teeth. Training of complex motor tasks has consistently been shown to trigger neuroplastic changes in corticomotor control and optimization of muscle function. It is not known if training...... and repeated food morsel splitting lead to changes in jaw muscle function. Objective: To investigate if repeated splitting of food morsels in participants with natural dentition changes the force and jaw muscle electromyographic (EMG) activity. Methods: Twenty healthy volunteers (mean age = 26.2 ± 3.9 years......) participated in a single one-hour session divided into six series. Each series consisted of ten trials of a standardized behavioral task (total of 60 trials). The behavioral task was to hold and split a food morsel (8 mm, 180 mg placebo tablet) placed on a bite force transducer with the anterior teeth...

  1. Acoustic Split-Beam Echosounder Data (EK60)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Southeast Fisheries Science Center Mississippi Laboratories collects data using Simrad EK60 scientific split-beam acoustic echosounders during resource...

  2. The homogeneous property and flux splitting in gas dynamics

    Science.gov (United States)

    Lerat, A.

    The homogeneous property of fluxes in gas dynamics is investigated, and its consequences concerning the flux splitting introduced by Steger and Warming (1981) are examined. It is shown that, for any hyperbolic system w sub t + f(w) sub x = 0 which satisfies the homogeneous property, the flux f(w) can be expressed in terms of the eigenvalues and eigenvectors of the matrix A(w) = df(w)/dw. This same result is also found to hold for the split fluxes f(+)(w) and f(-)(w). The problem of the validity of flux splitting is studied using these results. Three applications of flux splitting are then considered. The first application concerns uncentered schemes and particularly a precise analysis of their stability, the second is connected with a method for correcting the dispersive error of second-order accurate schemes, and the third deals with a nonreflective boundary condition.

  3. Recent Progress in Energy-Driven Water Splitting.

    Science.gov (United States)

    Tee, Si Yin; Win, Khin Yin; Teo, Wee Siang; Koh, Leng-Duei; Liu, Shuhua; Teng, Choon Peng; Han, Ming-Yong

    2017-05-01

    Hydrogen is readily obtained from renewable and non-renewable resources via water splitting by using thermal, electrical, photonic and biochemical energy. The major hydrogen production is generated from thermal energy through steam reforming/gasification of fossil fuel. As the commonly used non-renewable resources will be depleted in the long run, there is great demand to utilize renewable energy resources for hydrogen production. Most of the renewable resources may be used to produce electricity for driving water splitting while challenges remain to improve cost-effectiveness. As the most abundant energy resource, the direct conversion of solar energy to hydrogen is considered the most sustainable energy production method without causing pollutions to the environment. In overall, this review briefly summarizes thermolytic, electrolytic, photolytic and biolytic water splitting. It highlights photonic and electrical driven water splitting together with photovoltaic-integrated solar-driven water electrolysis.

  4. Mini-Split Heat Pumps Multifamily Retrofit Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Dentz, J.; Podorson, D.; Varshney, K.

    2014-05-01

    Mini-split heat pumps can provide space heating and cooling in many climates and are relatively affordable. These and other features make them potentially suitable for retrofitting into multifamily buildings in cold climates to replace electric resistance heating or other outmoded heating systems. This report investigates the suitability of mini-split heat pumps for multifamily retrofits. Various technical and regulatory barriers are discussed and modeling was performed to compare long-term costs of substituting mini-splits for a variety of other heating and cooling options. A number of utility programs have retrofit mini-splits in both single family and multifamily residences. Two such multifamily programs are discussed in detail.

  5. Opportunistic splitting for scheduling using a score-based approach

    KAUST Repository

    Rashid, Faraan

    2012-06-01

    We consider the problem of scheduling a user in a multi-user wireless environment in a distributed manner. The opportunistic splitting algorithm is applied to find the best group of users without reporting the channel state information to the centralized scheduler. The users find the best among themselves while requiring just a ternary feedback from the common receiver at the end of each mini-slot. The original splitting algorithm is modified to handle users with asymmetric channel conditions. We use a score-based approach with the splitting algorithm to introduce time and throughput fairness while exploiting the multi-user diversity of the network. Analytical and simulation results are given to show that the modified score-based splitting algorithm works well as a fair scheduling scheme with good spectral efficiency and reduced feedback. © 2012 IEEE.

  6. Endoscopic classification of representations of quasi-split unitary groups

    CERN Document Server

    Mok, Chung Pang

    2015-01-01

    In this paper the author establishes the endoscopic classification of tempered representations of quasi-split unitary groups over local fields, and the endoscopic classification of the discrete automorphic spectrum of quasi-split unitary groups over global number fields. The method is analogous to the work of Arthur on orthogonal and symplectic groups, based on the theory of endoscopy and the comparison of trace formulas on unitary groups and general linear groups.

  7. Spectral splitting for thermal management in photovoltaic cells

    Science.gov (United States)

    Apostoleris, Harry; Chiou, Yu-Cheng; Chiesa, Matteo; Almansouri, Ibraheem

    2017-09-01

    Spectral splitting is widely employed as a way to divide light between different solar cells or processes to optimize energy conversion. Well-understood but less explored is the use of spectrum splitting or filtering to combat solar cell heating. This has impacts both on cell performance and on the surrounding environment. In this manuscript we explore the design of spectral filtering systems that can improve the thermal and power-conversion performance of commercial PV modules.

  8. Split Octonion electrodynamics and unified fields of dyons

    International Nuclear Information System (INIS)

    Bisht, P.S.

    2004-01-01

    Split octonion electrodynamics has been developed in terms of Zorn's vector matrix realization by reformulating electromagnetic potential, current, field tensor and other dynamical quantities. Corresponding field equation (Unified Maxwell's equations) and equation of motion have been reformulated by means of split octonion and its Zorn vector realization in unique, simpler and consistent manner. It has been shown that this theory reproduces the dyon field equations in the absence of gravito-dyons and vice versa

  9. Visualization of the sequence of a couple splitting outside shop

    DEFF Research Database (Denmark)

    2015-01-01

    Visualization of tracks of couple walking together before splitting and one goes into shop the other waits outside. The visualization represents the sequence described in figure 7 in the publication 'Taking the temperature of pedestrian movement in public spaces'......Visualization of tracks of couple walking together before splitting and one goes into shop the other waits outside. The visualization represents the sequence described in figure 7 in the publication 'Taking the temperature of pedestrian movement in public spaces'...

  10. A Modified Halpern's Iterative Scheme for Solving Split Feasibility Problems

    Directory of Open Access Journals (Sweden)

    Jitsupa Deepho

    2012-01-01

    Full Text Available The purpose of this paper is to introduce and study a modified Halpern’s iterative scheme for solving the split feasibility problem (SFP in the setting of infinite-dimensional Hilbert spaces. Under suitable conditions a strong convergence theorem is established. The main result presented in this paper improves and extends some recent results done by Xu (Iterative methods for the split feasibility problem in infinite-dimensional Hilbert space, Inverse Problem 26 (2010 105018 and some others.

  11. Template-free synthesis of beta-In2S3 superstructures and their photocatalytic activity.

    Science.gov (United States)

    Amutha, R; Akilandeswari, S; Ahmmad, Bashir; Muruganandham, M; Sillanpää, Mika

    2010-12-01

    In this article, we have successfully fabricated various morphological beta-Indium sulfide (In2S3) superstructures by using indium thiocyanate complex at acidic pH. All the synthesis has been performed by a template-free, hydrothermal method at 195 degrees C for 3 h. The photocatalytic activity of synthesized In2S3 have been investigated by using UV-B (lamda = 365 nm) light with Methyl Orange dye as a model pollutant. The synthesized photocatalyst was characterized by using XRD, FE-SEM, HR-TEM, DRS spectra and nitrogen adsorption analysis. The influence of indium precursors and solvents on the morphology as well as the surface properties has also been discussed. The XRD result shows that cubic phase beta-In2S3 formed under all experimental conditions. A plausible mechanism of the In2S3 microsphere formation has been discussed based on experimental observations.

  12. Topological string in harmonic space and correlation functions in S3 stringy cosmology

    International Nuclear Information System (INIS)

    Saidi, El Hassan; Sedra, Moulay Brahim

    2006-01-01

    We develop the harmonic space method for conifold and use it to study local complex deformations of T*S 3 preserving manifestly SL(2,C) isometry. We derive the perturbative manifestly SL(2,C) invariant partition function Z top of topological string B model on locally deformed conifold. Generic n momentum and winding modes of 2D c=1 noncritical theory are described by highest υ (n,0) and lowest components υ (0,n) of SL(2,C) spin s=n2 multiplets (υ (n-k,k) ), 0= α + and V α - . We also derive a dictionary giving the passage from Laurent (Fourier) analysis on T*S 1 (S 1 ) to the harmonic method on T*S 3 (S 3 ). The manifestly SU(2,C) covariant correlation functions of the S 3 quantum cosmology model of Gukov-Saraikin-Vafa are also studied

  13. Analysis of CP conserving Higgs bosons self couplings in SM×S(3)

    International Nuclear Information System (INIS)

    Guevara, E Barradas; Félix-Beltrán, O; Rodríguez-Jáuregui, E

    2013-01-01

    We carry out a detailed analysis of a minimal S 3 -invariant extension of the Standard Model, with an extended S 3 -Higgs sector. Within this extended S(3)-Standard Model, we study the trilinear Higgs couplings and its dependence on the details of the model, even when the lightest Higgs boson mass is taken to be a fixed parameter. We study quantitatively the trilinear Higgs couplings, and compare these couplings to the corresponding Standard Model trilinear Higgs coupling in some regions of the parameter space. A precise measurement of the trilinear Higgs self coupling will also make it possible to test this extended S(3)-Standard Model with the Standard Model trilinear Higgs coupling. We present analytical expressions for the trilinear Higgs couplings

  14. Subcellular localization of Bombyx mori ribosomal protein S3a and ...

    African Journals Online (AJOL)

    USER

    2010-04-05

    Apr 5, 2010 ... piggybac-A3-EGFP and recombinant baculovirues expressing BmS3a-EGFP fusion protein (BV/IE1-. Bms3a-EGFP) or EGFP (BV/EGFP) were produced using BmNPV/Bac-to-Bac expression system. Results showed that the number of polyhedral in the transgenic cells of BmS3a was much smaller than.

  15. Hydrogen Production from Semiconductor-based Photocatalysis via Water Splitting

    Directory of Open Access Journals (Sweden)

    Jeffrey C. S. Wu

    2012-10-01

    Full Text Available Hydrogen is the ideal fuel for the future because it is clean, energy efficient, and abundant in nature. While various technologies can be used to generate hydrogen, only some of them can be considered environmentally friendly. Recently, solar hydrogen generated via photocatalytic water splitting has attracted tremendous attention and has been extensively studied because of its great potential for low-cost and clean hydrogen production. This paper gives a comprehensive review of the development of photocatalytic water splitting for generating hydrogen, particularly under visible-light irradiation. The topics covered include an introduction of hydrogen production technologies, a review of photocatalytic water splitting over titania and non-titania based photocatalysts, a discussion of the types of photocatalytic water-splitting approaches, and a conclusion for the current challenges and future prospects of photocatalytic water splitting. Based on the literatures reported here, the development of highly stable visible–light-active photocatalytic materials, and the design of efficient, low-cost photoreactor systems are the key for the advancement of solar-hydrogen production via photocatalytic water splitting in the future.

  16. Anodic Aluminum Oxide Membrane-Assisted Fabrication of β-In2S3Nanowires

    Science.gov (United States)

    2009-01-01

    In this study, β-In2S3nanowires were first synthesized by sulfurizing the pure Indium (In) nanowires in an AAO membrane. As FE-SEM results, β-In2S3nanowires are highly ordered, arranged tightly corresponding to the high porosity of the AAO membrane used. The diameter of the β-In2S3nanowires is about 60 nm with the length of about 6–8 μm. Moreover, the aspect ratio of β-In2S3nanowires is up to 117. An EDS analysis revealed the β-In2S3nanowires with an atomic ratio of nearly S/In = 1.5. X-ray diffraction and corresponding selected area electron diffraction patterns demonstrated that the β-In2S3nanowire is tetragonal polycrystalline. The direct band gap energy (Eg) is 2.40 eV from the optical measurement, and it is reasonable with literature. PMID:20596400

  17. Influence of Ag and Sn incorporation in In2S3 thin films

    Science.gov (United States)

    Lin, Ling-Yan; Yu, Jin-Ling; Cheng, Shu-Ying; Lu, Pei-Min

    2015-07-01

    Ag- and Sn-doped In2S3 thin films were deposited on glass substrates using the thermal evaporation technique. The doping was realized by thermal diffusion. The influences of Ag and Sn impurities on the electrical, structural, morphological, and optical properties of the In2S3 films were investigated. In all deposited samples, the x-ray diffraction spectra revealed the formation of cubic In2S3 phase. A significant increase in the crystallite size was observed after Ag doping, while the doping of Sn slightly decreased the crystallite size. The x-ray photoelectron spectroscopy verified the diffusion of Ag and Sn into the In2S3 films after annealing. The optical study illustrated that Ag doping resulted in a reduction of the optical band gap while Sn doping led to a widening of the gap. Optical properties were investigated to determine the optical constants. Besides, it was found that the resistivity decreases significantly either after Ag or Sn incorporation. The study demonstrates that the Sn-doped In2S3 thin films are more suitable for buffer layer application in solar cells than the Ag-doped In2S3 thin films. Project supported by the National Natural Science Foundation of China (Grant Nos. 61076063, 61340051, and 61306120) and the Natural Science Foundation of Fujian Province, China (Grant No. 2014J05073).

  18. Quantum confinement of Bi2S3 in glass with magnetic behavior

    Directory of Open Access Journals (Sweden)

    Rajendra P. Panmand

    2013-02-01

    Full Text Available The novel Bi2S3 quantum dots (QDs glass nanosystems with unique magnetic properties have been investigated. The monodispersed QDs of size in the range of 3 to 15 nm were grown in the glass matrix. The optical study of these nanosystems clearly demonstrated the size quantization effect resulting in a pronounced band gap variation with QD size. The magnetic properties of the pristine glass and the Bi2S3 QD glass nanosystems were investigated by VSM and SQUID magnetometer. The pristine glass did not show any ferromagnetism while the Bi2S3 glass nanosystems showed significant and reproducible ferromagnetism. We also investigated the effect of the size of Bi2S3 QDs on the magnetic properties. The saturation magnetization for the 15 nm QD glass-nanosystem (124 memu/g was observed to be higher as compared to the 3nm QD glass nanosystem (58.2 memu/g. The SQUID measurement gave the excellent hysteresis up to 300K. Surprisingly, the bulk Bi2S3 powder is diamagnetic in nature but Bi2S3 quantum dots glass nanosystem showed the ferromagnetic behavior for the first time. The investigated novel QD glass-nanosystem may have a potential application in spintronic devices and most importantly, this nanosystem can be fabricated in any usable shape as per the device requirement.

  19. Anodic Aluminum Oxide Membrane-Assisted Fabrication of β-In2S3Nanowires

    Directory of Open Access Journals (Sweden)

    Chen Chih-Jung

    2009-01-01

    Full Text Available Abstract In this study, β-In2S3nanowires were first synthesized by sulfurizing the pure Indium (In nanowires in an AAO membrane. As FE-SEM results, β-In2S3nanowires are highly ordered, arranged tightly corresponding to the high porosity of the AAO membrane used. The diameter of the β-In2S3nanowires is about 60 nm with the length of about 6–8 μm. Moreover, the aspect ratio of β-In2S3nanowires is up to 117. An EDS analysis revealed the β-In2S3nanowires with an atomic ratio of nearly S/In = 1.5. X-ray diffraction and corresponding selected area electron diffraction patterns demonstrated that the β-In2S3nanowire is tetragonal polycrystalline. The direct band gap energy (Eg is 2.40 eV from the optical measurement, and it is reasonable with literature.

  20. Effects of antimony trisulfide (Sb2S3) on sliding friction of automotive brake friction materials

    Science.gov (United States)

    Lee, Wan Kyu; Rhee, Tae Hee; Kim, Hyun Seong; Jang, Ho

    2013-09-01

    The effect of antimony trisulfide (Sb2S3) on the tribological properties of automotive brake friction materials was investigated using a Krauss type tribometer and a 1/5 scale dynamometer with a rigid caliper. Results showed that Sb2S3 improved fade resistance by developing transfer films on the disc surface at elevated temperatures. On the other hand, the rubbing surfaces of the friction material exhibited contact plateaus with a broader height distribution when it contained Sb2S3, indicating fewer contact junctions compared to the friction material with graphite. The friction material with Sb2S3 also exhibited a lower stick-slip propensity than the friction material with graphite. The improved fade resistance with Sb2S3 is attributed to its lubricating capability sustained at high temperatures, while the lower stick-slip propensity of the friction material with Sb2S3 is associated with the slight difference between its static and kinetic coefficients of friction and high normal stiffness.

  1. Numerical investigation of a dual-loop EGR split strategy using a split index and multi-objective Pareto optimization

    International Nuclear Information System (INIS)

    Park, Jungsoo; Song, Soonho; Lee, Kyo Seung

    2015-01-01

    Highlights: • Model-based control of dual-loop EGR system is performed. • EGR split index is developed to provide non-dimensional index for optimization. • EGR rates are calibrated using EGR split index at specific operating conditions. • Multi-objective Pareto optimization is performed to minimize NO X and BSFC. • Optimum split strategies are suggested with LP-rich dual-loop EGR at high load. - Abstract: A proposed dual-loop exhaust-gas recirculation (EGR) system that combines the features of high-pressure (HP) and low-pressure (LP) systems is considered a key technology for improving the combustion behavior of diesel engines. The fraction of HP and LP flows, known as the EGR split, for a given dual-loop EGR rate play an important role in determining the engine performance and emission characteristics. Therefore, identifying the proper EGR split is important for the engine optimization and calibration processes, which affect the EGR response and deNO X efficiencies. The objective of this research was to develop a dual-loop EGR split strategy using numerical analysis and one-dimensional (1D) cycle simulation. A control system was modeled by coupling the 1D cycle simulation and the control logic. An EGR split index was developed to investigate the HP/LP split effects on the engine performance and emissions. Using the model-based control system, a multi-objective Pareto (MOP) analysis was used to minimize the NO X formation and fuel consumption through optimized engine operating parameters. The MOP analysis was performed using a response surface model extracted from Latin hypercube sampling as a fractional factorial design of experiment. By using an LP rich dual-loop EGR, a high EGR rate was attained at low, medium, and high engine speeds, increasing the applicable load ranges compared to base conditions

  2. Simple and fast method for step size determination in computations of signal propagation through nonlinear fibres

    DEFF Research Database (Denmark)

    Rasmussen, Christian Jørgen

    2001-01-01

    Presents a simple and fast method for determination of the step size that exactly leads to a prescribed accuracy when signal propagation through nonlinear optical fibres is computed using the split-step Fourier method.......Presents a simple and fast method for determination of the step size that exactly leads to a prescribed accuracy when signal propagation through nonlinear optical fibres is computed using the split-step Fourier method....

  3. Giant magnon solution and dispersion relation in string theory in AdS3×S3×T4 with mixed flux

    International Nuclear Information System (INIS)

    Hoare, B.; Stepanchuk, A.; Tseytlin, A.A.

    2014-01-01

    We address the question of the exact form of the dispersion relation for light-cone string excitations in string theory in AdS 3 ×S 3 ×T 4 with mixed R–R and NS–NS 3-form fluxes. The analogy with string theory in AdS 5 ×S 5 suggests that in addition to the data provided by the perturbative near-BMN expansion and symmetry algebra considerations there is another source of information for the dispersion relation – the semiclassical giant magnon solution. In earlier work in (arXiv:1303.1037) and (arXiv:1304.4099) we found that the symmetry algebra constraints, which are consistent with a perturbative expansion, do not completely determine the form of the dispersion relation. The aim of the present paper is to fix the dispersion relation by constructing a generalisation of the known dyonic giant magnon soliton on S 3 to the presence of a non-zero NS–NS flux described by a WZ term in the string action (with coefficient q). We find that the angular momentum of this soliton gets shifted by a term linear in world-sheet momentum p. We also discuss the symmetry algebra of the string light-cone S-matrix and show that the exact dispersion relation, which should have the correct perturbative BMN and semiclassical giant magnon limits, should also contain such a linear momentum term. The simplicity of the resulting bound-state picture provides a strong argument in favour of this dispersion relation

  4. Light Illuminated α−Fe2O3/Pt Nanoparticles as Water Activation Agent for Photoelectrochemical Water Splitting

    Science.gov (United States)

    Li, Xiaodong; Wang, Zhi; Zhang, Zemin; Chen, Lulu; Cheng, Jianli; Ni, Wei; Wang, Bin; Xie, Erqing

    2015-01-01

    The photoelectrochemical (PEC) water splitting is hampered by strong bonds of H2O molecules and low ionic conductivity of pure water. The photocatalysts dispersed in pure water can serve as a water activation agent, which provides an alternative pathway to overcome such limitations. Here we report that the light illuminated α−Fe2O3/Pt nanoparticles may produce a reservoir of reactive intermediates including H2O2, ·OH, OH− and H+ capable of promoting the pure water reduction/oxidation half−reactions at cathode and highly photocatalytic−active TiO2/In2S3/AgInS2 photoanode, respectively. Remarkable photocurrent enhancement has been obtained with α−Fe2O3/Pt as water activation agent. The use of α−Fe2O3/Pt to promote the reactivity of pure water represents a new paradigm for reproducible hydrogen fuel provision by PEC water splitting, allowing efficient splitting of pure water without adding of corrosive chemicals or sacrificial agent. PMID:25773684

  5. Light illuminated α-Fe2O3/Pt nanoparticles as water activation agent for photoelectrochemical water splitting.

    Science.gov (United States)

    Li, Xiaodong; Wang, Zhi; Zhang, Zemin; Chen, Lulu; Cheng, Jianli; Ni, Wei; Wang, Bin; Xie, Erqing

    2015-03-16

    The photoelectrochemical (PEC) water splitting is hampered by strong bonds of H2O molecules and low ionic conductivity of pure water. The photocatalysts dispersed in pure water can serve as a water activation agent, which provides an alternative pathway to overcome such limitations. Here we report that the light illuminated α-Fe2O3/Pt nanoparticles may produce a reservoir of reactive intermediates including H2O2, ·OH, OH(-) and H(+) capable of promoting the pure water reduction/oxidation half-reactions at cathode and highly photocatalytic-active TiO2/In2S3/AgInS2 photoanode, respectively. Remarkable photocurrent enhancement has been obtained with α-Fe2O3/Pt as water activation agent. The use of α-Fe2O3/Pt to promote the reactivity of pure water represents a new paradigm for reproducible hydrogen fuel provision by PEC water splitting, allowing efficient splitting of pure water without adding of corrosive chemicals or sacrificial agent.

  6. Thermoelectric Properties for a Suspended Microribbon of Quasi-One-Dimensional TiS3

    Science.gov (United States)

    Sakuma, Tasuku; Nishino, Shunsuke; Miyata, Masanobu; Koyano, Mikio

    2018-02-01

    Transition-metal trichalcogenides MX3 (M = Ti, Zr, Nb, Ta; X = S, Se) are well-known inorganic quasi-one-dimensional conductors. Among them, we have investigated the thermoelectric properties of titanium trisulfide TiS3 microribbon. The electrical resistivity ρ, thermal conductivity κ, and thermoelectric power S were measured using 3ω method. The weight mean values were found to be ρ = 5 mω m and κ = 10 W K-1 m-1 along the one-dimensional direction (b-axis) of the TiS3 microribbon. Combined with the thermoelectric power S = -530 μV K-1, the figure of merit was calculated as ZT = 0.0023. This efficiency is the same as that of randomly oriented bulk TiS3. We also estimated the anisotropy of σ and κ using the present results and those for randomly oriented bulk material. The obtained weak anisotropy for TiS3 is attributable to strong coupling between triangular columns consisting of TiS3 units. These experimental results are consistent with theoretical results obtained using density functional theory (DFT) calculations.

  7. Luminescent Ag-doped In2S3 nanoparticles stabilized by mercaptoacetate in water and glycerol

    Science.gov (United States)

    Raevskaya, Alexandra E.; Ivanchenko, Maria V.; Stroyuk, Oleksandr L.; Kuchmiy, Stepan Ya.; Plyusnin, Victor F.

    2015-03-01

    Colloidal nanoparticles (NPs) of tetragonal β-In2S3 were stabilized in water and glycerol by mercaptoacetate anions. Doping of In2S3 NPs with AgI cations at the time of the synthesis imparts the NPs with the photoluminescence (PL) in the visible part of the spectrum. The doping results also in a shift of the absorption threshold and the PL band maximum to longer wavelengths proportional to the AgI content. The PL band maximum of AgI-doped In2S3 NPs can be varied from 575-580 to 760-765 nm by augmenting the silver(I) amount and the duration and temperature of the post-synthesis aging. The average radiative life-time of AgI-doped In2S3 NPs also depends on the silver(I) content and reaches the maximal value, 960 ns, at a molar Ag:In ratio of 1:4. The maximal quantum yield of stationary PL, 12 %, is observed at this Ag:In ratio as well. Deposition of a ZnS "shell" on the surface of AgI-doped In2S3 NPs results in an increase of the PL quantum yield to 30 %.

  8. Ultralong In2S3 Nanotubes on Graphene Substrate with Enhanced Electrocatalytic Activity.

    Science.gov (United States)

    Guo, Sheng-qi; Chen, Xue; Hu, Fang-zhong; Zhang, Qi-chun; Liu, Lu

    2015-09-16

    Ultralong one-dimensional (1D) nanostructures including nanowires or nanotubes have been extensively studied because of their widespread applications in many fields. Although a lot of methods have been reported to prepare In2S3 nanotubes, approaching these nanotubes through one-pot solution synthesis is still extremely difficult, probably because of the intrinsic isotropic crystal growth characteristic of In2S3. In this article, we demonstrated a self-assembly approach for hydrothermal synthesis of In2S3 nanotubes/graphene composites, which contain ultralong (up to 10 μm) In2S3 nanotubes on graphene substrate. The influence of several important synthetic parameters on the final products has been systematically investigated. Importantly, the as-prepared In2S3 nanotubes/graphene composites can be easily cast on FTO to form a film, which can be used as a counter electrode. Our research indicates that the as-fabricated counter electrode exhibits excellent electrocatalytic activity toward the iodide species (I-/I3-) reduction reaction and very high energy conversion efficiency (8.01%) in dye-sensitized solar cells.

  9. Tuning photocatalytic activity of In2S3 broadband spectrum photocatalyst based on morphology

    Science.gov (United States)

    Chen, Jun; Liu, Wenxia; Gao, Wenwen

    2016-04-01

    Efficient utilization of full solar light especially near-infrared light (NIR) is still a great challenge. Herein three In2S3 nanomaterials with cubic phase and different morphologies were synthesized via hydrothermal methods by using sodium sulfide (Na2S), thiosemicarbazide (TSC) and thioacetamide (TAA) as sulfur sources, respectively. All the as-synthesized In2S3 samples were found to be photo-active under either UV, visible or NIR light irradiation although they possess very different morphologies. The In2S3 sample with irregular and plate-like nanoparticles synthesized by using Na2S as sulfur source shows the highest activity on photodegradation of methyl orange due to its exposure of more photoactive (311) plane than the other two In2S3 samples and the occurrence of lattice oxygen. The samples that synthesized by using TSC and TAA as sulfur sources possess the morphology of hollow microspheres, which are hierarchically constructed by thinner nanosheets and cumulated by thicker platelets, respectively. The microsphere sample constructed by thinner nanosheets shows even lower photocatalytic activity than that accumulated by thicker platelets under all the tested light regions especially under longer irradiation time because of its less exposed (311) plane and lower sulfur vacancies although it possesses a far larger specific surface area than the latter. These results suggest that the exposure of more photoactive (311) plane and occurrence of lattice oxygen deserve more attention to improve the photocatalytic activity of In2S3.

  10. Synthesis and Characterization of Sb2S3 Nanorods via Complex Decomposition Approach

    Directory of Open Access Journals (Sweden)

    Abdolali Alemi

    2011-01-01

    Full Text Available Based on the complex decomposition approach, a simple hydrothermal method has been developed for the synthesizing of Sb2S3 nanorods with high yield in 24 h at 150∘C. The powder X-ray diffraction pattern shows the Sb2S3 crystals belong to the orthorhombic phase with calculated lattice parameters a=1.120 nm, b=1.128 nm, and c=0.383 nm. The quantification of energy dispersive X-ray spectrometric analysis peaks give an atomic ratio of 2 : 3 for Sb : S. TEM and SEM studies reveal that the appearance of the as-prepared Sb2S3 is rod-like which is composed of nanorods with the typical width of 30–160 nm and length of up to 6 μm. High-resolution transmission electron microscopic (HRTEM studies reveal that the Sb2S3 is oriented in the [10-1] growth direction. The band gap calculated from the absorption spectra is found to be 3.29 ev, indicating a considerable blue shift relative to the bulk. The formation mechanism of Sb2S3 nanostructures is proposed.

  11. Modular Invariance of Conformal Field Theory on S^{1}×S^{3} and Circle Fibrations.

    Science.gov (United States)

    Shaghoulian, Edgar

    2017-09-29

    I conjecture a high-temperature-low-temperature duality for conformal field theories defined on circle fibrations like S^{3} and its lens space family. The duality is an exchange between the thermal circle and the fiber circle in the limit where both are small. The conjecture is motivated by the fact that π_{1}(S^{3}/Z_{p→∞})=Z=π_{1}(S^{1}×S^{2}) and the Gromov-Hausdorff distance between S^{3}/Z_{p→∞} and S^{1}/Z_{p→∞}×S^{2} vanishes. Several checks of the conjecture are provided: free fields, N=1 theories in four dimensions (which shows that the Di Pietro-Komargodski supersymmetric Cardy formula and its generalizations are given exactly by a supersymmetric Casimir energy), N=4 super Yang-Mills at strong coupling, and the six-dimensional N=(2,0) theory. For all examples considered, the duality is powerful enough to control the high-temperature asymptotics on the unlensed S^{3}, relating it to the Casimir energy on a highly lensed S^{3}. Such large-order quotients are more generally useful for studying quantum field theory on curved spacetimes.

  12. Using S3 cloud storage with ROOT and CvmFS

    Science.gov (United States)

    Arsuaga-Ríos, María; Heikkilä, Seppo S.; Duellmann, Dirk; Meusel, René; Blomer, Jakob; Couturier, Ben

    2015-12-01

    Amazon S3 is a widely adopted web API for scalable cloud storage that could also fulfill storage requirements of the high-energy physics community. CERN has been evaluating this option using some key HEP applications such as ROOT and the CernVM filesystem (CvmFS) with S3 back-ends. In this contribution we present an evaluation of two versions of the Huawei UDS storage system stressed with a large number of clients executing HEP software applications. The performance of concurrently storing individual objects is presented alongside with more complex data access patterns as produced by the ROOT data analysis framework. Both Huawei UDS generations show a successful scalability by supporting multiple byte-range requests in contrast with Amazon S3 or Ceph which do not support these commonly used HEP operations. We further report the S3 integration with recent CvmFS versions and summarize the experience with CvmFS/S3 for publishing daily releases of the full LHCb experiment software stack.

  13. Verres du systeme la 2S 3La 2O 3Ga 2O 3Ga 2S 3

    Science.gov (United States)

    Guittard, M.; Loireau-Lozac'H, A. M.; Berguer, F.; Barnier, S.; Flahaut, J.

    1986-04-01

    The extent of the glass forming region is described as a function of the composition and of the cooling speed. The shape of this region is explained from the previously described La 2S 3La 2O 3Ga 2O 3Ga 2S 3 phase diagram. Glasses are obtained after relatively slow cooling (5°/min), in a definite region of compositions, which coincides with a relatively large concentration of ternary invariants. The thermal properties (transition temperatures and crystallization temperatures) were measured by DTA. For a relatively large region of compositions, glasses return to the equilibrium conditions with intermediate formation of the La 3.33Ga 6S 12O 2 metastable crystalline phase. An approach to the structure of the glasses is made by comparison with the crystal structures of the numerous ternary and quaternary crystalline compounds observed in the system, and by the comparison of the Raman spectra. It appears that these gallium oxysulfide glasses have many structural analogies with germanium sulfide glasses.

  14. Tune-out wavelength for the 1 s 2 s3 S - 1 s 3 p 3 P transition of helium: relativistic effects

    Science.gov (United States)

    Drake, Gordon W. F.; Manalo, Jacob

    2017-04-01

    The tune-out wavelength is the wavelength at which the frequency dependent polarizability of an atom vanishes. It can be measured to very high precision by means of an interferometric comparison between two beams. This paper is part of a joint theoretical/ experimental project with K. Baldwin et al. (Australian National University) and L.-Y. Tang et al. (Wuhan Institute of Physics and Mathematics) to perform a high precision comparison between theory and experiment as a probe of atomic structure, including relativistic and quantum electrodynamic effects. We will report the results of calculations for the tune-out wavelength that is closest to the 1 s 2 s3 S - 1 s 3 p3 P transition of 4He. Our result for the M = 0 magnetic substate, obtained with a fully correlated Hylleraas basis set, is 413 . 079 958 51 (12) nm. This includes a leading relativistic contribution of - 0 . 059 218 5 (16) nm from the Breit interaction as a perturbation, and a relativistic recoil contribution of - 0 . 000 044 47 (17) nm. The results will be compared with recent relativistic CI calculations. Research supported by tha Natural Sciences and Engineering Research Council of Canada.

  15. An Examination Of Fracture Splitting Parameters Of Crackable Connecting Rods

    Directory of Open Access Journals (Sweden)

    Zafer Özdemir

    2000-06-01

    Full Text Available Fracture splitting method is an innovative processing technique in the field of automobile engine connecting rod (con/rod manufacturing. Compared with traditional method, this technique has remarkable advantages. Manufacturing procedures, equipment and tools investment can be decreased and energy consumption reduced remarkably. Furthermore, product quality and bearing capability can also be improved. It provides a high quality, high accuracy and low cost route for producing connecting rods (con/rods. With the many advantages mentioned above, this method has attracted manufacturers attention and has been utilized in many types of con/rod manufacturing. In this article, the method and the advantages it provides, such as materials, notches for fracture splitting, fracture splitting conditions and fracture splitting equipment are discussed in detail. The paper describes an analysis of examination of fracture splitting parameters and optik-SEM fractography of C70S6 crackable connectıng rod. Force and velocity parameters are investigated. That uniform impact force distrubition starting from the starting notch causes brittle and cleavage failure mode is obtained as a result. This induces to decrease the toughness.

  16. New Splitting Criteria for Decision Trees in Stationary Data Streams.

    Science.gov (United States)

    Jaworski, Maciej; Duda, Piotr; Rutkowski, Leszek

    2017-05-10

    The most popular tools for stream data mining are based on decision trees. In previous 15 years, all designed methods, headed by the very fast decision tree algorithm, relayed on Hoeffding's inequality and hundreds of researchers followed this scheme. Recently, we have demonstrated that although the Hoeffding decision trees are an effective tool for dealing with stream data, they are a purely heuristic procedure; for example, classical decision trees such as ID3 or CART cannot be adopted to data stream mining using Hoeffding's inequality. Therefore, there is an urgent need to develop new algorithms, which are both mathematically justified and characterized by good performance. In this paper, we address this problem by developing a family of new splitting criteria for classification in stationary data streams and investigating their probabilistic properties. The new criteria, derived using appropriate statistical tools, are based on the misclassification error and the Gini index impurity measures. The general division of splitting criteria into two types is proposed. Attributes chosen based on type-$I$ splitting criteria guarantee, with high probability, the highest expected value of split measure. Type-$II$ criteria ensure that the chosen attribute is the same, with high probability, as it would be chosen based on the whole infinite data stream. Moreover, in this paper, two hybrid splitting criteria are proposed, which are the combinations of single criteria based on the misclassification error and Gini index.

  17. Experimental study on dynamic splitting of recycled concrete using SHPB

    Science.gov (United States)

    Lu, Yubin; Yu, Shuisheng; Cai, Yong

    2015-09-01

    To study the recycled concrete splitting tensile properties and fracture state with various recycled coarse aggregate replacement percentage (i.e. 0%, 25%, 50%, 75% and 100%), the dynamic splitting test of recycled concrete was carried out using large diameter (75 mm) split Hopkinson pressure bar (SHPB). The results show that the recycled concrete splitting tensile strength increases with the increase of loading rate, and the loading rate also affects the recycled concrete fracture state, which indicates that the recycled concrete has obvious rate sensitivity. The damage state of the recycled concrete is not only the destruction of the interface between coarse aggregate and cement mortar, but also associates with the fracture damage of aggregates. Under the same water cement ratio, when the replacement percentage of coarse aggregates is around 50%-75%, the gradation of natural and recycled coarse aggregate is optimal, and thus the splitting tensile strength is the largest. This study offers theoretical basis for the engineering applications of recycled concrete.

  18. Alveolar Ridge Split Technique Using Piezosurgery with Specially Designed Tips

    Directory of Open Access Journals (Sweden)

    Alessandro Moro

    2017-01-01

    Full Text Available The treatment of patients with atrophic ridge who need prosthetic rehabilitation is a common problem in oral and maxillofacial surgery. Among the various techniques introduced for the expansion of alveolar ridges with a horizontal bone deficit is the alveolar ridge split technique. The aim of this article is to give a description of some new tips that have been specifically designed for the treatment of atrophic ridges with transversal bone deficit. A two-step piezosurgical split technique is also described, based on specific osteotomies of the vestibular cortex and the use of a mandibular ramus graft as interpositional graft. A total of 15 patients were treated with the proposed new tips by our department. All the expanded areas were successful in providing an adequate width and height to insert implants according to the prosthetic plan and the proposed tips allowed obtaining the most from the alveolar ridge split technique and piezosurgery. These tips have made alveolar ridge split technique simple, safe, and effective for the treatment of horizontal and vertical bone defects. Furthermore the proposed piezosurgical split technique allows obtaining horizontal and vertical bone augmentation.

  19. Accessing magnetic chalcogenides with solvothermal synthesis: KFeS2 and KFe2S3

    Science.gov (United States)

    Han, Insung; Jiang, Zhelong; dela Cruz, Clarina; Zhang, Hong; Sheng, Huaping; Bhutani, Ankita; Miller, Dean J.; Shoemaker, Daniel P.

    2018-04-01

    Semiconducting binary sulfides are often produced with controlled size and shape by solvothermal synthesis using amine solvents. The versatility of this method, however, has not been extended to dense ternary sulfides that include alkali and transition metal ions, which are renowned for their complex magnetic and electronic properties. We report the solvothermal synthesis of the alkali-transition metal sulfides KFeS2 and KFe2S3. The latter compound is not accessible by direct solid-state synthesis. Magnetic susceptibility measurements indicate antiferromagnetic ordering of KFeS2 and KFe2S3, which contain single and double chains of FeS4 tetrahedra, respectively. Given the ability to access KFe2S3 here, further development of this method may lead to isolation of new functional compounds.

  20. Micro Structural Analysis of In2S3 Thin Films by Raman Spectroscopy

    Science.gov (United States)

    Izadneshana, H.; Gremenok, V. F.

    2014-11-01

    In2S3 thin films with different thicknesses were deposited on glass substrates using the thermal evaporation method. The as-deposited films were annealed in vacuum at 330 and 400°C for 30 and 60 min. We used Raman spectroscopy and X-ray diffraction to evaluate the effect of thermal treatment on the film structures. Raman active modes that can be classified as 9A1 and 14E modes have been observed in the Raman spectra of the In2S3 thin films. Variations in the Raman shift and bandwidth of different In2S3 thin films reveal the influence of the annealing effect. Results of Raman spectroscopy and XRD show that the annealing effect changes the crystallization phase from tetragonal to cubic at high temperatures.

  1. Report on the search for binary black holes inspiral in S3 LIGO data

    International Nuclear Information System (INIS)

    Cokelaer, Thomas

    2006-01-01

    We report on the search for gravitational waves emitted by non-spinning binary black hole inspirals in the data taken during the third LIGO science run (S3). We give an overview of the data acquired during S3 and the target waveforms that we are searching for in this analysis. We briefly describe how the data was filtered using a BCV detection template family (using an hexagonal template bank placement in the mass parameter plane). Finally, we report on preliminary estimates of the sensitivity of the three LIGO detectors using software injections of effective one-body waveforms with component masses in the range 3-40 M o-dot and total mass M ≤ 40 M o-dot . We show that during S3, the three LIGO detectors have a detection efficiency of 50% up to several Mpc for L1 and H2, and up to 30 Mpc for H1

  2. KF addition to Cu2SnS3 thin films prepared by sulfurization process

    Science.gov (United States)

    Nakashima, Mitsuki; Fujimoto, Junya; Yamaguchi, Toshiyuki; Sasano, Junji; Izaki, Masanobu

    2017-04-01

    Cu2SnS3 thin films were fabricated by sulfurization with KF addition and applied to photovoltaic devices. Two methods, two-stage annealing and the use of four-layer precursors, were employed, and the quantity of NaF and KF and the annealing temperature were changed. By electron probe microanalysis (EPMA), the Cu/Sn mole ratio was found to range from 0.81 to 1.51. The X-ray diffraction (XRD) patterns and Raman spectra indicated that the fabricated thin films had a monoclinic Cu2SnS3 structure. The Cu2SnS3 thin films fabricated by two-stage annealing had a close-packed structure and a pinhole-free surface morphology. The best solar cell in this study showed V oc of 293 mV, which surpassed the previously reported value.

  3. Adjuvant antiproliferative and cytotoxic effect of aloin in irradiated HeLaS3 cells

    Science.gov (United States)

    Nićiforović, A.; Adžić, M.; Zarić, B.; Radojčić, M. B.

    2007-09-01

    Naturally occurring phytoanthracycline, aloin, was used to radiosensitize HeLaS3 human cervix carcinoma cells. The results indicated that the cytotoxic adjuvant effect of aloin was synergistic with gammaionizing radiation at all drug concentrations and comparable to the cytotoxicity of 5-10 Gy ionizing radiation alone. Radiosensitization of HeLaS3 cells was achieved by 60 μM aloin, which reduced the IC50 dose of ionizing radiation from 3.4 to 2 Gy. Ionizing radiation and aloin alone or in combination are shown to cause perturbation of the HeLaS3 cell-cycle and increase the percentage of cells in the DNA synthesis (S) phase of the cell cycle. While either of the agents applied alone causes programmed cell death by apoptosis, the simultaneous cell damage by both agents through the altered redox balance compromised cell capacity to conduct this program and led to synergic cytotoxic cell death by necrosis.

  4. Canonical structure of BHT massive gravity in warped AdS3 sector

    Directory of Open Access Journals (Sweden)

    Davood Mahdavian Yekta

    2016-08-01

    Full Text Available We investigate the asymptotic structure of the three dimensional Warped Anti-de Sitter (WAdS3 black holes in the Bergshoeff–Hohm–Townsend (BHT massive gravity using the canonical Hamiltonian formalism. We define the canonical asymptotic gauge generators, which produce the conserved charges and the asymptotic symmetry group for the WAdS3 black holes. The attained symmetry group is described by a semi-direct sum of a Virasoro and a Kač–Moody algebra. Using the Sugawara construction, we obtain a direct sum of two Virasoro algebras. We show that not only the asymptotic conserved charges satisfy the first law of black hole thermodynamics, but also they lead to the expected Smarr formula for the WAdS3 black holes. We also show that the black hole's entropy obeys the Cardy formula of the dual conformal field theory (CFT.

  5. SplitRacer - a semi-automatic tool for the analysis and interpretation of teleseismic shear-wave splitting

    Science.gov (United States)

    Reiss, Miriam Christina; Rümpker, Georg

    2017-04-01

    We present a semi-automatic, graphical user interface tool for the analysis and interpretation of teleseismic shear-wave splitting in MATLAB. Shear wave splitting analysis is a standard tool to infer seismic anisotropy, which is often interpreted as due to lattice-preferred orientation of e.g. mantle minerals or shape-preferred orientation caused by cracks or alternating layers in the lithosphere and hence provides a direct link to the earth's kinematic processes. The increasing number of permanent stations and temporary experiments result in comprehensive studies of seismic anisotropy world-wide. Their successive comparison with a growing number of global models of mantle flow further advances our understanding the earth's interior. However, increasingly large data sets pose the inevitable question as to how to process them. Well-established routines and programs are accurate but often slow and impractical for analyzing a large amount of data. Additionally, shear wave splitting results are seldom evaluated using the same quality criteria which complicates a straight-forward comparison. SplitRacer consists of several processing steps: i) download of data per FDSNWS, ii) direct reading of miniSEED-files and an initial screening and categorizing of XKS-waveforms using a pre-set SNR-threshold. iii) an analysis of the particle motion of selected phases and successive correction of the sensor miss-alignment based on the long-axis of the particle motion. iv) splitting analysis of selected events: seismograms are first rotated into radial and transverse components, then the energy-minimization method is applied, which provides the polarization and delay time of the phase. To estimate errors, the analysis is done for different randomly-chosen time windows. v) joint-splitting analysis for all events for one station, where the energy content of all phases is inverted simultaneously. This allows to decrease the influence of noise and to increase robustness of the measurement

  6. Experiments on In2S3:Sn Thin Films with up to 1% Tin Content

    Science.gov (United States)

    Kraini, M.; Bouguila, N.; Koaib, J.; Vázquez-Vázquez, C.; López-Quintela, M. A.; Alaya, S.

    2016-11-01

    Tin-doped indium sulfide (In2S3:Sn) thin films with different Sn:In molar ratios (0% to 1% by mol in solution) have been deposited on glass substrates by a chemical spray pyrolysis method. The films were investigated by x-ray diffraction analysis, optical absorption, Raman, and photoluminescence spectroscopies, field-emission scanning electron microscopy, energy-dispersive x-ray spectroscopy, and atomic force microscopy. The structural properties revealed that the In2S3:Sn thin films had polycrystalline cubic structure with average crystallite size increasing from 16.3 nm to 25.5 nm. The surface morphology of the films was continuous and crack free. The average and root-mean-square roughness increased from 13.12 nm to 31.65 nm and from 16.14 nm to 39.39 nm, respectively, with increasing Sn:In molar ratio. Raman studies revealed the presence of vibration modes related to In2S3 phase, with no signature of secondary phases. The transmission coefficient was about 65% to 70% in the visible region and 70% to 90% in the near-infrared region. The optical bandgap values for allowed direct transitions in In2S3:Sn were found to lie in the range from 2.68 eV to 2.80 eV. The refractive index of the In2S3:Sn thin films decreased from 2.45 to 2.37 while the k values lay in the range from 0.02 to 0.25 for all wavelengths. Defect-related photoluminescence properties are also discussed. These In2S3:Sn films are promising candidates for use in optoelectronic and photovoltaic devices.

  7. A role for proteins S3 and S14 in the 30 S ribosomal subunit.

    Science.gov (United States)

    Ramakrishnan, V; Graziano, V; Capel, M S

    1986-11-15

    Small ribosomal subunits prepared by the method of Kirillov et al. (Kirillov, S. V., Makhno, V. I., Peshin, N. N., and Semenkov, Yu. P. (1986) Nucleic Acids Res. 5, 4305-4315) are active but fail to reconstitute. The inability to reconstitute is due to a deficiency in proteins S3 and S14. Supplementation of the protein component with pure S3 and S14 leads to an enhancement of the activity of the reconstituted product. Our results provide evidence that these two proteins are involved in assembly but may not be required once the 30 S subunit has been properly assembled.

  8. Pulsed laser deposition from ZnS and Cu2SnS3 multicomponent targets

    DEFF Research Database (Denmark)

    Ettlinger, Rebecca Bolt; Cazzaniga, Andrea Carlo; Canulescu, Stela

    2015-01-01

    Thin films of ZnS and Cu2SnS3have been produced by pulsed laser deposition (PLD), the latter for the firsttime. The effect of fluence and deposition temperature on the structure and the transmission spectrumas well as the deposition rate has been investigated, as has the stoichiometry of the films...... transferredfrom target to substrate. Elemental analysis by energy dispersive X-ray spectroscopy indicates lower Sand Sn content in Cu2SnS3films produced at higher fluence, whereas this trend is not seen in ZnS. Thedeposition rate of the compound materials measured in atoms per pulse is considerably larger than...

  9. Structure and resonances of the e+–He(1s2s 3Se) system

    International Nuclear Information System (INIS)

    Ren Zhenzhong; Han Huili; Shi Tingyun; Mitroy, J

    2012-01-01

    We have studied the geometry and resonances of the e + He( 3 S e ) system in the framework of hyperspherical coordinates. A model potential proposed by us is used to describe the interaction between the out electron with the He + ionic core. The calculated binding energy and expectation distance of the system are in agreement with other calculations. In addition, two resonances below the e + –He(1s3s 3 S e ) threshold and one resonance below the Ps(n=2)–He + threshold are identified. (paper)

  10. Adjuvant antiproliferative and cytotoxic effect of aloin in irradiated HeLaS3 cells

    International Nuclear Information System (INIS)

    Niciforovic, A.; Adzic, M.; Vucic, V.; Radojcic, M.B.

    2006-01-01

    Naturally occurring phytoanthracycline, aloin, was used to radiosensitize HeLaS3 human cervix carcinoma cells. The results indicated that the cytotoxic adjuvant effect of aloin was synergistic with IR at all drug concentrations and comparable to the cytotoxicity of 5-10Gy IR alone. Radiosensitization of HeLaS3 cells was achieved by 60μM aloin which reduced IC 50 dose of IR from 3.4- to 2Gy. The cell damage by both agents compromised cell capacity to conduct programmed cell death by apoptosis, and led to the synergic cytotoxic cell death by necrosis. (author)

  11. Hydrothermal Synthesis of Bi2S3 Nanostructures and ABS-Based Polymeric Nanocomposite

    Directory of Open Access Journals (Sweden)

    D. Ghanbari

    2014-04-01

    Full Text Available Bismuth sulfide nano-rods and nano-flowers were synthesized via a hydrothermal reaction at a relatively low temperature. Thioglycolic acid is used as sulfur source and capping agent simultaneously. Bi2S3 nanostructures were then added to acrylonitrile-butadiene-styrene (ABS copolymer. The thermal stability behavior of ABS filled with bismuth sulfide nano-rods were investigated by thermogravimetric analysis (TGA. Nanostructures were characterized by X-ray diffraction (XRD, scanning electron microscopy (SEM and atomic force microscopy (AFM. The flame retardancy behavior of ABS-Bi2S3 was studied by UL-94 analysis.

  12. Benzannulated tris(2-mercapto-1-imidazolyl)hydroborato ligands: tetradentate κ4-S3H binding and access to monomeric monovalent thallium in an [S3] coordination environment.

    Science.gov (United States)

    Rong, Yi; Palmer, Joshua H; Parkin, Gerard

    2014-01-21

    The benzannulated tris(mercaptoimidazolyl)borohydride sodium complex, [Tm(Bu(t)Benz)]Na, has been synthesized via the reaction of NaBH4 with 1-tert-butyl-1,3-dihydro-2H-benzimidazole-2-thione, while [Tm(MeBenz)]K has been synthesized via the reaction of KBH4 with 1-methyl-1,3-dihydro-2H-benzimidazole-2-thione. The molecular structures of the solvated adducts, {[Tm(Bu(t)Benz)]Na(THF)}2(μ-THF)2 and [Tm(MeBenz)]K(OCMe2)3, have been determined by X-ray diffraction, which demonstrates that the [Tm(R)] ligands in these complexes adopt different coordination modes to that in {[Tm(MeBenz)]Na}2(μ-THF)3. Specifically, while the [Tm(MeBenz)] ligand of the sodium complex {[Tm(MeBenz)]Na}2(μ-THF)3 adopts a κ(3)-S3 coordination mode, the potassium complex [Tm(MeBenz)]K(OCMe2)3 adopts a most uncommon inverted κ(4)-S3H coordination mode in which the potassium binds to all three sulfur donors and the hydrogen of the B-H group in a linear KH-B manner. Furthermore, the [Tm(Bu(t)Benz)] ligand of {[Tm(Bu(t)Benz)]Na(THF)}2(μ-THF)2 adopts a κ(3)-S2H coordination mode, thereby demonstrating the flexibility of this ligand system. The monovalent thallium compounds, [Tm(MeBenz)]Tl and [Tm(Bu(t)Benz)]Tl, have been obtained via the corresponding reactions of [Tm(MeBenz)]Na and [Tm(Bu(t)Benz)]Na with TlOAc. X-ray diffraction demonstrates that the three sulfur donors of the [Tm(RBenz)] ligands of both [Tm(MeBenz)]Tl and [Tm(Bu(t)Benz)]Tl chelate to thallium. This coordination mode is in marked contrast to that in other [Tm(R)]Tl compounds, which exist as dinuclear molecules wherein two of the sulfur donors coordinate to different thallium centers. As such, this observation provides further evidence that benzannulation promotes κ(3)-S3 coordination in this system.

  13. The Differences Between Stock Splits and Stock Dividends

    DEFF Research Database (Denmark)

    Bechmann, Ken L.; Raaballe, Johannes

    It is often asserted that stock splits and stock dividends are purely cosmetic events. However, many studies have documented several stock market effects associated with stock splits and stock dividends. This paper examines the effects of these two types of events for the Danish stock market...... different. Second, the positive stock market reaction is closely related to associated changes in a firm's payout policy, but the relationship varies for the two types of events. Finally, there is only very weak evidence for a change in the liquidity of the stock. On the whole, after controlling...... for the firm's payout policy, the results suggest that a stock split is a cosmetic event and that a stock dividend on its own is considered negative news....

  14. Electron refrigeration in hybrid structures with spin-split superconductors

    Science.gov (United States)

    Rouco, M.; Heikkilä, T. T.; Bergeret, F. S.

    2018-01-01

    Electron tunneling between superconductors and normal metals has been used for an efficient refrigeration of electrons in the latter. Such cooling is a nonlinear effect and usually requires a large voltage. Here we study the electron cooling in heterostructures based on superconductors with a spin-splitting field coupled to normal metals via spin-filtering barriers. The cooling power shows a linear term in the applied voltage. This improves the coefficient of performance of electron refrigeration in the normal metal by shifting its optimum cooling to lower voltage, and also allows for cooling the spin-split superconductor by reverting the sign of the voltage. We also show how tunnel coupling spin-split superconductors with regular ones allows for a highly efficient refrigeration of the latter.

  15. Giant Rashba spin splitting in Bi2Se3: Tl

    KAUST Repository

    Singh, Nirpendra

    2014-07-25

    First-principles calculations are employed to demonstrate a giant Rashba spin splitting in Bi2Se3:Tl. Biaxial tensile and compressive strain is used to tune the splitting by modifying the potential gradient. The band gap is found to increase under compression and decreases under tension, whereas the dependence of the Rashba spin splitting on the strain is the opposite. Large values of αR = 1.57 eV Å at the bottom of the conduction band (electrons) and αR = 3.34 eV Å at the top of the valence band (holes) are obtained without strain. These values can be further enhanced to αR = 1.83 eV Å and αR = 3.64 eV Å, respectively, by 2% tensile strain. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Stride length asymmetry in split-belt locomotion.

    Science.gov (United States)

    Hoogkamer, Wouter; Bruijn, Sjoerd M; Duysens, Jacques

    2014-01-01

    The number of studies utilizing a split-belt treadmill is rapidly increasing in recent years. This has led to some confusion regarding the definitions of reported gait parameters. The purpose of this paper is to clearly present the definitions of the gait parameters that are commonly used in split-belt treadmill studies. We argue that the modified version of stride length for split-belt gait, which is different from the standard definition of stride length and actually is a measure of limb excursion, should be referred to as 'limb excursion' in future studies. Furthermore, the symmetry of stride length and stride time is specifically addressed. Copyright © 2013 Elsevier B.V. All rights reserved.

  17. Geometric inductance effects in the spectrum of split transmon qubits

    Science.gov (United States)

    Brierley, R. T.; Blumoff, J.; Chou, K.; Schoelkopf, R. J.; Girvin, S. M.

    2014-03-01

    The low-energy spectra of transmon superconducting qubits in a cavity can be accurately calculated using the black-box quantization approach. This method involves finding the normal modes of the circuit with a linearized Josephson junction and using these as the basis in which to express the non-linear terms. A split transmon qubit consists of two Josephson junctions in a SQUID loop. This configuration allows the Josephson energy to be tuned by applying external flux. Ideally, the system otherwise behaves as a conventional transmon with a single effective Josephson junction. However, the finite geometric inductance of the SQUID loop causes deviations from the simplest ideal description of a split transmon. This alters both the linearized and non-linear behaviour of the Josephson junctions in the superconducting circuit. We study how these changes can be incorporated into the black-box quantization approach and their effects on the low-energy spectrum of the split transmon.

  18. Point splitting in a curved space-time background

    International Nuclear Information System (INIS)

    Liggatt, P.A.J.; Macfarlane, A.J.

    1979-01-01

    A prescription is given for point splitting in a curved space-time background which is a natural generalization of that familiar in quantum electrodynamics and Yang-Mills theory. It is applied (to establish its validity) to the verification of the gravitational anomaly in the divergence of a fermion axial current. Notable features of the prescription are that it defines a point-split current that can be differentiated straightforwardly, and that it involves a natural way of averaging (four-dimensionally) over the directions of point splitting. The method can extend directly from the spin-1/2 fermion case treated to other cases, e.g., to spin-3/2 Rarita-Schwinger fermions. (author)

  19. Splitting rules for spectra of two-dimensional Fibonacci quasilattices

    Science.gov (United States)

    Yang, Xiangbo; Liu, Youyan

    1997-10-01

    In the framework of the single-electron tight-binding on-site model, after establishing the method of constructing a class of two-dimensional Fibonacci quasilattices, we have studied the rules of energy spectra splitting for these quasilattices by means of a decomposition-decimation method based on the renormalization-group technique. Under the first approximation, the analytic results show that there exist only six kinds of clusters and the electronic energy bands split as type Y and consist of nine subbands. Instead of the on-site model, the transfer model should be used for the higher hierarchy of the spectra, the electronic energy spectra split as type F. The analytic results are confirmed by numerical simulations.

  20. Tantalum nitride for photocatalytic water splitting: concept and applications

    Directory of Open Access Journals (Sweden)

    Ela Nurlaela

    2016-10-01

    Full Text Available Abstract Along with many other solar energy conversion processes, research on photocatalytic water splitting to generate hydrogen and oxygen has experienced rapid major development over the past years. Developing an efficient visible-light-responsive photocatalyst has been one of the targets of such research efforts. In this regard, nitride materials, particularly Ta3N5, have been the subject of investigation due to their promising properties. This review focuses on the fundamental parameters involved in the photocatalytic processes targeting overall water splitting using Ta3N5 as a model photocatalyst. The discussion primarily focuses on relevant parameters that are involved in photon absorption, exciton separation, carrier diffusion, carrier transport, catalytic efficiency, and mass transfer of the reactants. An overview of collaborative experimental and theoretical approaches to achieve efficient photocatalytic water splitting using Ta3N5 is discussed.

  1. Split and delay photon correlation spectroscopy with a visible light

    International Nuclear Information System (INIS)

    Rasch, Marten

    2016-04-01

    The development and performance of a setup constructed with the aim for the split pulse photon correlation spectroscopy is presented in this thesis. The double pulse time structure is accomplished with help of an Acusto-Optic Modulator (AOM) crystal, which mimics the splitting and delaying of photon pulses. The setup provides double pulses and allows to control the pulse width and delay and to synchronize them into one camera exposure window. The performance of the setup was successfully verified in a proof of principle experiment with a model system of polystyrene particles following Brownian motion. The measured radius of particles obtained with from the split pulse experiment (R h =(2.567±0.097) μm) is in agreement with the particle size provided by the manufacturer (R=(2.26±0.08) μm). The achieved results show higher statistics compared to a standard Dynamic Light Scattering (DLS) measurement.

  2. Guidelines to Develop Efficient Photocatalysts for Water Splitting

    KAUST Repository

    Garcia Esparza, Angel T.

    2016-04-03

    Photocatalytic overall water splitting is the only viable solar-to-fuel conversion technology. The research discloses an investigation process wherein by dissecting the photocatalytic water splitting device, electrocatalysts, and semiconductor photocatalysts can be independently studied, developed and optimized. The assumption of perfect catalysts leads to the realization that semiconductors are the limiting factor in photocatalysis. This dissertation presents a guideline for efficient photocatalysis using semiconductor particles developed from idealized theoretical simulations. No perfect catalysts exist; then the discussion focus on the development of efficient non-noble metal electrocatalysts for hydrogen evolution from water reduction. Tungsten carbide (WC) is selective for the catalysis of hydrogen without the introduction of the reverse reaction of water formation, which is critical to achieving photocatalytic overall water splitting as demonstrated in this work. Finally, photoelectrochemistry is used to characterize thoroughly Cu-based p-type semiconductors with potential for large-scale manufacture. Artificial photosynthesis may be achieved by following the recommendations herein presented.

  3. Rabi splitting in an acoustic cavity embedded plate

    International Nuclear Information System (INIS)

    Ni, Xu; Liu, Xiao-Ping; Chen, Ze-Guo; Zheng, Li-Yang; Xu, Ye-Long; Lu, Ming-Hui; Chen, Yan-Feng

    2014-01-01

    We design a structure to realize Rabi splitting and Rabi oscillation in acoustics. We develop rigorous analytical models to analyze the splitting effect from the aspect of phase matching, and from the aspect of mode coupling using a coupled mode model. In this model, we discover that the splitting effect is caused by the coupling of the Fabry–Perot fundamental mode with the resonant mode of an artificial acoustic ‘atom’. We then extract the coupling strength and analyze the impact of structural parameters on it. In addition, we demonstrate Rabi oscillation in the time domain. Such quantum phenomena in the classical regime may have potential applications in the design of novel ultrasonic devices.

  4. Immediate Loaded Implants in Split-Crest Procedure.

    Science.gov (United States)

    Crespi, Roberto; Bruschi, Giovanni B; Gastaldi, Giorgio; Capparé, Paolo; Gherlone, Enrico F

    2015-10-01

    The aim of this study was to assess survival rate of immediate loading implants placed after split-crest technique. Thirty-six patients were enrolled in the study. They underwent placement of 93 dental implants in edentulous region after split-crest ridge expansion procedure. Implants followed an immediate loading procedure. Crestal bone levels were measured at baseline, at temporary prosthesis placement, at 1 year, and at 2 years from implant placement. For dental implants, a survival rate of 98.92% was reported at 2-year follow-up, with a mean value bone loss of -1.02 ± 0.48. This study assessed immediate loading implant placement after split-crest procedure at 2-year follow-up. © 2015 Wiley Periodicals, Inc.

  5. A Matrix Splitting Method for Composite Function Minimization

    KAUST Repository

    Yuan, Ganzhao

    2016-12-07

    Composite function minimization captures a wide spectrum of applications in both computer vision and machine learning. It includes bound constrained optimization and cardinality regularized optimization as special cases. This paper proposes and analyzes a new Matrix Splitting Method (MSM) for minimizing composite functions. It can be viewed as a generalization of the classical Gauss-Seidel method and the Successive Over-Relaxation method for solving linear systems in the literature. Incorporating a new Gaussian elimination procedure, the matrix splitting method achieves state-of-the-art performance. For convex problems, we establish the global convergence, convergence rate, and iteration complexity of MSM, while for non-convex problems, we prove its global convergence. Finally, we validate the performance of our matrix splitting method on two particular applications: nonnegative matrix factorization and cardinality regularized sparse coding. Extensive experiments show that our method outperforms existing composite function minimization techniques in term of both efficiency and efficacy.

  6. Advanced split-illumination electron holography without Fresnel fringes

    International Nuclear Information System (INIS)

    Tanigaki, Toshiaki; Aizawa, Shinji; Park, Hyun Soon; Matsuda, Tsuyoshi; Harada, Ken; Shindo, Daisuke

    2014-01-01

    Advanced split-illumination electron holography was developed by employing two biprisms in the illuminating system to split an electron wave into two coherent waves and two biprisms in the imaging system to overlap them. A focused image of an upper condenser-biprism filament was formed on the sample plane, and all other filaments were placed in its shadow. This developed system makes it possible to obtain precise reconstructed object waves without modulations due to Fresnel fringes, in addition to holograms of distant objects from reference waves. - Highlights: • Advanced split-illumination electron holography without Fresnel fringes is developed. • Two biprisms are installed in illuminating system of microscope. • High-precision holographic observations of an area locating far from the sample edge become possible

  7. Tantalum nitride for photocatalytic water splitting: concept and applications

    KAUST Repository

    Nurlaela, Ela

    2016-10-12

    Along with many other solar energy conversion processes, research on photocatalytic water splitting to generate hydrogen and oxygen has experienced rapid major development over the past years. Developing an efficient visible-light-responsive photocatalyst has been one of the targets of such research efforts. In this regard, nitride materials, particularly Ta3N5, have been the subject of investigation due to their promising properties. This review focuses on the fundamental parameters involved in the photocatalytic processes targeting overall water splitting using Ta3N5 as a model photocatalyst. The discussion primarily focuses on relevant parameters that are involved in photon absorption, exciton separation, carrier diffusion, carrier transport, catalytic efficiency, and mass transfer of the reactants. An overview of collaborative experimental and theoretical approaches to achieve efficient photocatalytic water splitting using Ta3N5 is discussed.

  8. A Split G-Quadruplex and Graphene Oxide-Based Low-Background Platform for Fluorescence Authentication of Pseudostellaria heterophylla

    Directory of Open Access Journals (Sweden)

    Zhenzhu Zheng

    2014-12-01

    Full Text Available A label-free split G-quadruplex and graphene oxide (GO-based fluorescence platform has been designed to distinguish Pseudostellaria heterophylla (PH from its adulterants based on the differences in their nrDNA ITS sequences. Herein, GO has been first introduced to capture G-rich probes with 2:2 split mode and then decrease the background signal. As T-DNA exists, the probes leave the GO surface to form double-stranded structures followed by the formation of the overhanging G-rich sequence into a G-quadruplex structure, which combines quinaldine red specifically to produce a strong fluorescence signal. In addition, this strategy allows detection of T-DNA in a wide range of concentrations from 1.0 × 10−8 to 2.0 × 10−6 mol·L−1 with a detection limit of 7.8 × 10−9 mol·L−1. We hope that the split G-quadruplex/GO platform can be utilized to further develop gene identification sensors in Traditional Chinese Medicine or other analysis areas.

  9. A comparison between kinetic flux vector splitting and flux difference splitting methods in solution of Euler equations

    International Nuclear Information System (INIS)

    Mirzaei, M.; Shahverdi, M.

    2004-01-01

    This paper is proposed to compare the performances of deferent inviscid flux approximation methods in solution of two-dimensional Euler equations. The methods belong to two different group of flux splitting methods: flux difference splitting (FDS) methods and kinetic flux vector splitting (KFVS) method. Here Roe method and Osher method belonging to flux difference splitting (FDS) group have been employed and their performances are compared with that of kinetic flux vector splitting method (KFVS). Roe and Osher methods are based on approximate solution of Riemann problem over computational cell surfaces while the KFVS has a quit different base. In KFVS inviscid fluxes are approximated based on the kinetic theory and correlation between Boltzmann equation and Euler equations. For comparison the performances of the above mentioned methods three different problems have been solved. The first problem is flow over a 10 degree compression-expansion ramp with Mach number of 2.0, the second one is a transonic flow with Mach number of 0.85 over a 4.2% circular bump in a duct and the third is supersonic flow with Mach number of 3.0 over a circular blunt slab. (author)

  10. Splitting and non splitting are pollution models photochemical reactions in the urban areas of greater Tehran area

    International Nuclear Information System (INIS)

    Heidarinasab, A.; Dabir, B.; Sahimi, M.; Badii, Kh.

    2003-01-01

    During the past years, one of the most important problems has been air pollution in urban areas. In this regards, ozone, as one of the major products of photochemical reactions, has great importance. The term 'photochemical' is applied to a number of secondary pollutants that appear as a result of sun-related reactions, ozone being the most important one. So far various models have been suggested to predict these pollutants. In this paper, we developed the model that has been introduced by Dabir, et al. [4]. In this model more than 48 chemical species and 114 chemical reactions are involved. The result of this development, showed good to excellent agreement across the region for compounds such as O 3 , NO, NO 2 , CO, and SO 2 with regard to VOC and NMHC. The results of the simulation were compared with previous work [4] and the effects of increasing the number of components and reactions were evaluated. The results of the operator splitting method were compared with non splitting solving method. The result showed that splitting method with one-tenth time step collapsed with non splitting method (Crank-Nicolson, under-relaxation iteration method without splitting of the equation terms). Then we developed one dimensional model to 3-D and were compared with experimental data

  11. Screening current induced magnetic field in REBCO superconducting coil wound by using split wire having intermittent inner split

    Science.gov (United States)

    Matsuda, Tetsuro; Jin, Xinzhe; Okamura, Tetsuji

    2017-09-01

    REBCO-coated conductor having a high critical current is promising for applications in next generation apparatuses such as ultra-high field NMR, high-resolution MRI, and high-precision accelerator. However, it has an important challenge for application in NMR and MRI, due to the single core in REBCO superconducting layer. The single core induces a large screening current-induced magnetic field (screening current field), and it influences the controlling of center field in NMR/MRI magnet. To reduce the screening current field, we have recently developed a split wire having multi-core structure by inner split method (electrical separation by bending stress, ESBS). In experiment, short samples with linear inner split by a large bending stress of 80 N were prepared and tested. However, to fabricate a long length wire with good quality, it is better to use a smaller bending stress. In this study, a low-bending-stress inner split method is used to fabricate superconducting tapes with longitudinal split in their superconducting layer. The fabrication and experimental assessments for the wire and coil are carried out.

  12. Tantalum-based semiconductors for solar water splitting.

    Science.gov (United States)

    Zhang, Peng; Zhang, Jijie; Gong, Jinlong

    2014-07-07

    Solar energy utilization is one of the most promising solutions for the energy crises. Among all the possible means to make use of solar energy, solar water splitting is remarkable since it can accomplish the conversion of solar energy into chemical energy. The produced hydrogen is clean and sustainable which could be used in various areas. For the past decades, numerous efforts have been put into this research area with many important achievements. Improving the overall efficiency and stability of semiconductor photocatalysts are the research focuses for the solar water splitting. Tantalum-based semiconductors, including tantalum oxide, tantalate and tantalum (oxy)nitride, are among the most important photocatalysts. Tantalum oxide has the band gap energy that is suitable for the overall solar water splitting. The more negative conduction band minimum of tantalum oxide provides photogenerated electrons with higher potential for the hydrogen generation reaction. Tantalates, with tunable compositions, show high activities owning to their layered perovskite structure. (Oxy)nitrides, especially TaON and Ta3N5, have small band gaps to respond to visible-light, whereas they can still realize overall solar water splitting with the proper positions of conduction band minimum and valence band maximum. This review describes recent progress regarding the improvement of photocatalytic activities of tantalum-based semiconductors. Basic concepts and principles of solar water splitting will be discussed in the introduction section, followed by the three main categories regarding to the different types of tantalum-based semiconductors. In each category, synthetic methodologies, influencing factors on the photocatalytic activities, strategies to enhance the efficiencies of photocatalysts and morphology control of tantalum-based materials will be discussed in detail. Future directions to further explore the research area of tantalum-based semiconductors for solar water splitting

  13. Rabi-like splitting from large area plasmonic microcavity

    Directory of Open Access Journals (Sweden)

    Fatemeh Hosseini Alast

    2017-08-01

    Full Text Available Rabi-like splitting was observed from a hybrid plasmonic microcavity. The splitting comes from the coupling of cavity mode with the surface plasmon polariton mode; anti-crossing was observed alongside the modal conversional channel on the reflection light measurement. The hybrid device consists of a 10x10 mm2 ruled metal grating integrated onto the Fabry-Perot microcavity. The 10x10 mm2 ruled metal grating fabricated from laser interference and the area is sufficiently large to be used in the practical optical device. The larger area hybrid plasmonic microcavity can be employed in polariton lasers and biosensors.

  14. Optimal Cross-Validation Split Ratio: Experimental Investigation

    DEFF Research Database (Denmark)

    Goutte, Cyril; Larsen, Jan

    1998-01-01

    Cross-validation is a common method for assessing the generalisation ability of a model in order to tune a regularisation parameter or otherhyper-parameters of a learning process. The use of cross-validation requires to set yet an additional parameter, the split rati. While a few texts haveinvest......Cross-validation is a common method for assessing the generalisation ability of a model in order to tune a regularisation parameter or otherhyper-parameters of a learning process. The use of cross-validation requires to set yet an additional parameter, the split rati. While a few texts...

  15. SiC MOSFETs based split output half bridge inverter

    DEFF Research Database (Denmark)

    Li, Helong; Munk-Nielsen, Stig; Beczkowski, Szymon

    2014-01-01

    output. The double pulse test shows the devices' current during commutation process and the reduced switching losses of SiC MOSFETs compared to that of the traditional half bridge. The efficiency comparison is presented with experimental results of half bridge power inverter with split output...... and traditional half bridge inverter, from switching frequency 10 kHz to 100 kHz. The experimental results comparison shows that the half bridge with split output has an efficiency improvement of more than 0.5% at 100 kHz switching frequency....

  16. Cooper Pair Splitting by Means of Graphene Quantum Dots

    Science.gov (United States)

    Tan, Z. B.; Cox, D.; Nieminen, T.; Lähteenmäki, P.; Golubev, D.; Lesovik, G. B.; Hakonen, P. J.

    2015-03-01

    A split Cooper pair is a natural source for entangled electrons which is a basic ingredient for quantum information in the solid state. We report an experiment on a superconductor-graphene double quantum dot (QD) system, in which we observe Cooper pair splitting (CPS) up to a CPS efficiency of ˜10 % . With bias on both QDs, we are able to detect a positive conductance correlation across the two distinctly decoupled QDs. Furthermore, with bias only on one QD, CPS and elastic cotunneling can be distinguished by tuning the energy levels of the QDs to be asymmetric or symmetric with respect to the Fermi level in the superconductor.

  17. Frobenius splitting and geometry of $G$-Schubert varieties

    DEFF Research Database (Denmark)

    He, Xuhua; Thomsen, Jesper Funch

    2008-01-01

    Let X be an equivariant embedding of a connected reductive group G over an algebraically closed field k of positive characteristic. Let B denote a Borel subgroup of G. A G-Schubert variety in X is a subvariety of the form diag(G) V , where V is a B×B -orbit closure in X. In the case where X...... admits a stable Frobenius splitting along an ample divisors. Although this indicates that G-Schubert varieties have nice singularities we present an example of a nonnormal G-Schubert variety in the wonderful compactification of a group of type G2 . Finally we also extend the Frobenius splitting results...

  18. Modulated-splitting-ratio fiber-optic temperature sensor

    Science.gov (United States)

    Beheim, Glenn; Anthan, Donald J.; Rys, John R.; Fritsch, Klaus; Ruppe, Walter R.

    1989-06-01

    A fiber-optic temperature sensor is described that uses a small silicon beamsplitter whose splitting ratio varies as a function of temperature. A four-beam technique is used to measure the sensor's temperature-indicating splitting ratio. This referencing method provides a measurement that is largely independent of the transmission properties of the sensor's optical fiber link. A significant advantage of this sensor, relative to other fiber-optic sensors, is its high stability, which permits the fiber-optic components to be readily substituted, thereby simplifying the sensor's installation and maintenance.

  19. Split-plot Experiments with Unusual Numbers of Subplot Runs

    DEFF Research Database (Denmark)

    Kulahci, Murat

    2007-01-01

    In many experimental situations, it may not be feasible or even possible to run experiments in a completely randomized fashion as usually recommended. Under these circumstances, split-plot experiments in which certain factors are changed less frequently than the others are often used. Most...... of the literature on split-plot designs is based on 2-level factorials. For those designs, the number of subplots is a power of 2. There may however be some situations where for cost purposes or physical constraints, we may need to have unusual number of subplots such as 3, 5, 6, etc. In this article, we explore...

  20. Novel Split Chest Tube Improves Post-Surgical Thoracic Drainage

    Science.gov (United States)

    Olivencia-Yurvati, Albert H; Cherry, Brandon H; Gurji, Hunaid A; White, Daniel W; Newton, J Tyler; Scott, Gary F; Hoxha, Besim; Gourlay, Terence; Mallet, Robert T

    2014-01-01

    Objective Conventional, separate mediastinal and pleural tubes are often inefficient at draining thoracic effusions. Description We developed a Y-shaped chest tube with split ends that divide within the thoracic cavity, permitting separate intrathoracic placement and requiring a single exit port. In this study, thoracic drainage by the split drain vs. that of separate drains was tested. Methods After sternotomy, pericardiotomy, and left pleurotomy, pigs were fitted with separate chest drains (n=10) or a split tube prototype (n=9) with internal openings positioned in the mediastinum and in the costo-diaphragmatic recess. Separate series of experiments were conducted to test drainage of D5W or 0.58 M sucrose, an aqueous solution with viscosity approximating that of plasma. One litre of fluid was infused into the thorax, and suction was applied at −20 cm H2O for 30 min. Results When D5W was infused, the split drain left a residual volume of 53 ± 99 ml (mean value ± SD) vs. 148 ± 120 for the separate drain (P=0.007), representing a drainage efficiency (i.e. drained vol/[drained + residual vol]) of 95 ± 10% vs. 86 ± 12% for the separate drains (P = 0.011). In the second series, the split drain evacuated more 0.58 M sucrose in the first minute (967 ± 129 ml) than the separate drains (680 ± 192 ml, P<0.001). By 30 min, the split drain evacuated a similar volume of sucrose vs. the conventional drain (1089 ± 72 vs. 1056 ± 78 ml; P = 0.5). Residual volume tended to be lower (25 ± 10 vs. 62 ± 72 ml; P = 0.128) and drainage efficiency tended to be higher (98 ± 1 vs. 95 ± 6%; P = 0.111) with the split drain vs. conventional separate drains. Conclusion The split chest tube drained the thoracic cavity at least as effectively as conventional separate tubes. This new device could potentially alleviate postoperative complications. PMID:25478289

  1. Modulation of forelimb and hindlimb muscle activity during quadrupedal tied-belt and split-belt locomotion in intact cats.

    Science.gov (United States)

    Frigon, A; Thibaudier, Y; Hurteau, M-F

    2015-04-02

    The modulation of the neural output to forelimb and hindlimb muscles when the left and right sides step at different speeds from one another in quadrupeds was assessed by obtaining electromyography (EMG) in seven intact adult cats during split-belt locomotion. To determine if changes in EMG during split-belt locomotion were modulated according to the speed of the belt the limb was stepping on, values were compared to those obtained during tied-belt locomotion (equal left-right speeds) at matched speeds. Cats were chronically implanted for EMG, which was obtained from six muscles: biceps brachii, triceps brachii, flexor carpi ulnaris, sartorius, vastus lateralis and medial gastrocnemius. During tied-belt locomotion, cats stepped from 0.4 to 1.0m/s in 0.1m/s increments whereas during split-belt locomotion, cats stepped with left-right speed differences of 0.1 to 0.4m/s in 0.1m/s increments. During tied-belt locomotion, EMG burst durations and mean EMG amplitudes of all muscles respectively decreased and increased with increasing speed. During split-belt locomotion, there was a clear differential modulation of the EMG patterns between flexors and extensors and between the slow and fast sides. Changes in the EMG pattern of some muscles could be explained by the speed of the belt the limb was stepping on, while in other muscles there were clear dissociations from tied-belt values at matched speeds. Therefore, results show that EMG patterns during split-belt locomotion are modulated to meet task requirements partly via signals related to the stepping speed of the homonymous limb and from the other limbs. Copyright © 2015 IBRO. Published by Elsevier Ltd. All rights reserved.

  2. FRET controlled photoluminescence in β-In2S3 microflower—Au nanoparticle ensemble

    Science.gov (United States)

    Warrier, Anita R.; Parameswaran, Chithra; Bingi, Jayachandra; Vijayan, C.

    2016-06-01

    We report on the exciton-plasmon interaction and fluorescence resonance energy transfer controlled photoluminescence quenching and switching in β-In2S3 microflowers dispersed in Au nanoparticle colloid. The strong resonant interaction of excited β-In2S3 microflowers with the surface plasmons of Au nanoparticles (˜520 nm) lead to shift in the excitonic binding energy (2.4 eV) with a magnitude of ˜50 meV. In the proximity of Au nanoparticles, the broad emission spectrum of β-In2S3 microflowers with prominent peak at wavelength of ˜540 nm is quenched and the peak switches to wavelength of ˜600 nm. We demonstrate that the quenching and switching of emission band depends on the rate of fluorescence resonance energy transfer, extent of spectral overlap and β-In2S3 microflowers (donor)- Au nanoparticles (acceptor) distance. This study opens the wide possibility of fabricating sensors and photonic devices with tunable optical properties.

  3. Structure reinvestigation of α-, β- and γ-In2S3.

    Science.gov (United States)

    Pistor, Paul; Merino Álvarez, Jose M; León, Máximo; di Michiel, Marco; Schorr, Susan; Klenk, Reiner; Lehmann, Sebastian

    2016-06-01

    Semiconducting indium sulfide (In2S3) has recently attracted considerable attention as a buffer material in the field of thin film photovoltaics. Compared with this growing interest, however, detailed characterizations of the crystal structure of this material are rather scarce and controversial. In order to close this gap, we have carried out a reinvestigation of the crystal structure of this material with an in situ X-ray diffraction study as a function of temperature using monochromatic synchrotron radiation. For the purpose of this study, high quality polycrystalline In2S3 material with nominally stoichiometric composition was synthesized at high temperatures. We found three modifications of In2S3 in the temperature range between 300 and 1300 K, with structural phase transitions at temperatures of 717 K and above 1049 K. By Rietveld refinement we extracted the crystal structure data and the temperature coefficients of the lattice constants for all three phases, including a high-temperature trigonal γ-In2S3 modification.

  4. Transport Properties Of Cu 2 S n S 3 Thin Films | Kuku | Nigeria ...

    African Journals Online (AJOL)

    A single source vacuum evaporation process has been employed to prepare thin films of Cu2SnS3. Electrical Hall measurements using Van der Pauw technique have revealed that film resistivity was a strong function of the substrate temperature for film deposition. The activation energy for the resistivity was 0.268 eV for ...

  5. Antipodal universes in the topology S3xR and H3xR

    International Nuclear Information System (INIS)

    Sasse, F.D.; Soares, I.D.; Tiomno, J.

    1988-01-01

    We introduce a two-parameter family of left-invariant metrics gL and right-invariant metrics gR on the Lie groups S 3 XR and H 3 XR with the aim of characterizing causality features in such universes. (M.W.O.) [pt

  6. Depth enhancement of S3D content and the psychological effects

    Science.gov (United States)

    Hirahara, Masahiro; Shiraishi, Saki; Kawai, Takashi

    2012-03-01

    Stereoscopic 3D (S3D) imaging technologies are widely used recently to create content for movies, TV programs, games, etc. Although S3D content differs from 2D content by the use of binocular parallax to induce depth sensation, the relationship between depth control and the user experience remains unclear. In this study, the user experience was subjectively and objectively evaluated in order to determine the effectiveness of depth control, such as an expansion or reduction or a forward or backward shift in the range of maximum parallactic angles in the cross and uncross directions (depth bracket). Four types of S3D content were used in the subjective and objective evaluations. The depth brackets of comparison stimuli were modified in order to enhance the depth sensation corresponding to the content. Interpretation Based Quality (IBQ) methodology was used for the subjective evaluation and the heart rate was measured to evaluate the physiological effect. The results of the evaluations suggest the following two points. (1) Expansion/reduction of the depth bracket affects preference and enhances positive emotions to the S3D content. (2) Expansion/reduction of the depth bracket produces above-mentioned effects more notable than shifting the cross/uncross directions.

  7. On the ultraviolet light induced oxidation of amorphous As2S3 film

    Czech Academy of Sciences Publication Activity Database

    Knotek, P.; Vlček, Milan; Kincl, Miloslav; Tichý, Ladislav

    2012-01-01

    Roč. 520, č. 16 (2012), s. 5472-5478 ISSN 0040-6090 R&D Projects: GA ČR GA203/09/0827 Institutional research plan: CEZ:AV0Z40500505 Keywords : As2S3 * arsenic sulfide * thin films Subject RIV: CA - Inorganic Chemistry Impact factor: 1.604, year: 2012

  8. Room temperature synthesis of crystalline Sb2S3 for SnO2 ...

    Indian Academy of Sciences (India)

    Abstract. The preparation of crystalline antimony sulphide (Sb2S3) by chemical route at room temperature was reported in this paper. The structural, morphological and optical properties of as-synthesized sample were system- atically investigated. X-ray diffraction (XRD) analysis confirms the orthorhombic crystal phase for ...

  9. EIF2S3 Mutations Associated with Severe X-Linked Intellectual Disability Syndrome MEHMO.

    Science.gov (United States)

    Skopkova, Martina; Hennig, Friederike; Shin, Byung-Sik; Turner, Clesson E; Stanikova, Daniela; Brennerova, Katarina; Stanik, Juraj; Fischer, Ute; Henden, Lyndal; Müller, Ulrich; Steinberger, Daniela; Leshinsky-Silver, Esther; Bottani, Armand; Kurdiova, Timea; Ukropec, Jozef; Nyitrayova, Olga; Kolnikova, Miriam; Klimes, Iwar; Borck, Guntram; Bahlo, Melanie; Haas, Stefan A; Kim, Joo-Ran; Lotspeich-Cole, Leda E; Gasperikova, Daniela; Dever, Thomas E; Kalscheuer, Vera M

    2017-04-01

    Impairment of translation initiation and its regulation within the integrated stress response (ISR) and related unfolded-protein response has been identified as a cause of several multisystemic syndromes. Here, we link MEHMO syndrome, whose genetic etiology was unknown, to this group of disorders. MEHMO is a rare X-linked syndrome characterized by profound intellectual disability, epilepsy, hypogonadism and hypogenitalism, microcephaly, and obesity. We have identified a C-terminal frameshift mutation (Ile465Serfs) in the EIF2S3 gene in three families with MEHMO syndrome and a novel maternally inherited missense EIF2S3 variant (c.324T>A; p.Ser108Arg) in another male patient with less severe clinical symptoms. The EIF2S3 gene encodes the γ subunit of eukaryotic translation initiation factor 2 (eIF2), crucial for initiation of protein synthesis and regulation of the ISR. Studies in patient fibroblasts confirm increased ISR activation due to the Ile465Serfs mutation and functional assays in yeast demonstrate that the Ile465Serfs mutation impairs eIF2γ function to a greater extent than tested missense mutations, consistent with the more severe clinical phenotype of the Ile465Serfs male mutation carriers. Thus, we propose that more severe EIF2S3 mutations cause the full MEHMO phenotype, while less deleterious mutations cause a milder form of the syndrome with only a subset of the symptoms. © 2017 WILEY PERIODICALS, INC.

  10. Updated German S3-guideline regarding the diagnosis of Crohn's disease. Implementation of radiological modalities

    International Nuclear Information System (INIS)

    Schreyer, A.G.; Ludwig, D.; Koletzko, S.; Hoffmann, J.C.; Preiss, J.C.; Zeitz, M.; Stange, E.; Herrlinger, K.R.

    2010-01-01

    The recently updated German S3-guideline regarding the diagnosis and treatment of Crohn's disease incorporates several changes concerning the radiological approach compared to the former guideline. This article focuses on guideline-based radiological imaging techniques for patients with Crohn's disease. The new guideline is also compared to former European and German guidelines in the context of recently published radiological literature. (orig.)

  11. Theoretical Study of the AC Conduction in β-In2S3

    Science.gov (United States)

    Abassi, H.; Bouguila, N.; Timoumi, A.

    2018-02-01

    β-In2S3 is of great interest in photovoltaic applications and presents a certain number of vacant sites allowing the displacement of indium atoms by hopping from one site to another. Recently, it has been shown that it exhibits ionic behavior. Experimental works have been carried out in order to study the alternating current (AC) conductivity in β-In2S3, showing the validity of the hopping model (correlated barrier hopping; CBH) in the frequency range not exceeding ω = 104 Hz. For ω > 104 Hz, the transport mechanism was dominated by small polaron tunneling (SPT). The theoretical model developed in this work in order to study the AC conductivity is based on the hopping model adapted to the case of β-In2S3 by considering the jump of indium ions from one site to another. We report the frequency and temperature dependence on β-In2S3 AC conductivity. An examination of the experimental results shows a qualitative compatibility of our model. Indeed, our theoretical simulations are in agreement with the experimental data in the same frequency range where the CBH model was dominant. A quantitative discrepancy between theory and experiment has been observed beyond this frequency range where the SPT has been dominant. This discrepancy increases by raising the temperature. A FORTRAN program based on the Lenvenberg-Marquardt method was established to determine the fitting curve of the theoretical model to the experimental. This program allowed us to deduce the vibration frequencies about the equilibrium of indium atoms in the case of β-In2S3 which are parameters of fundamental importance in solid-state physics. The vibration modes obtained from the numerical simulation are in agreement with the orders of magnitude found in the literature.

  12. Distributed traffic signal control using fuzzy logic

    Science.gov (United States)

    Chiu, Stephen

    1992-01-01

    We present a distributed approach to traffic signal control, where the signal timing parameters at a given intersection are adjusted as functions of the local traffic condition and of the signal timing parameters at adjacent intersections. Thus, the signal timing parameters evolve dynamically using only local information to improve traffic flow. This distributed approach provides for a fault-tolerant, highly responsive traffic management system. The signal timing at an intersection is defined by three parameters: cycle time, phase split, and offset. We use fuzzy decision rules to adjust these three parameters based only on local information. The amount of change in the timing parameters during each cycle is limited to a small fraction of the current parameters to ensure smooth transition. We show the effectiveness of this method through simulation of the traffic flow in a network of controlled intersections.

  13. Signal detection

    International Nuclear Information System (INIS)

    Tholomier, M.

    1985-01-01

    In a scanning electron microscope, whatever is the measured signal, the same set is found: incident beam, sample, signal detection, signal amplification. The resulting signal is used to control the spot luminosity with the observer cathodoscope. This is synchronized with the beam scanning on the sample; on the cathodoscope, the image in secondary electrons, backscattered electrons,... of the sample surface is reconstituted. The best compromise must be found between a register time low enough to remove eventual variations (under the incident beam) of the nature of the observed phenomenon, and a good spatial resolution of the image and a signal-to-noise ratio high enough. The noise is one of the basic limitations of the scanning electron microscope performance. The whose measurement line must be optimized to reduce it [fr

  14. Remarkably Enhancing Green-Excitation Efficiency for Solar Energy Utilization: Red Phosphors Ba2ZnS3:Eu2+, X-Co-Doped Halide Ions (X = Cl, Br, I).

    Science.gov (United States)

    Luo, Tingting; Du, Yun; Qiu, Zhongxian; Li, Yanmei; Wang, Xiaofang; Zhou, Wenli; Zhang, Jilin; Yu, Liping; Lian, Shixun

    2017-05-15

    Eu 2+ -activated Ba 2 ZnS 3 has been reported as a red phosphor with a broad emission band peaking at 650 nm under blue excitation for white-LED. In this study, Ba 2 ZnS 3 :Eu 2+ , X - (X = F, Cl, Br, I) phosphors doped with halide ions were prepared by traditional high-temperature solid-state reaction. Phase identification of powders was performed by X-ray powder diffraction analysis, confirming the existence of single-phase Ba 2 ZnS 3 crystals without dopant. The corresponding excitation spectra showed an additional broad band in the green region peaking at 550 nm when the phosphor was halogenated except by the smallest F - . It was proved that the green-excitation efficiency successively strengthened from Cl - , to Br - , to I - , which suggested larger halide ions made a greater contribution to the further splitting of the t 2g energy level of the doped Eu 2+ ions in the host Ba 2 ZnS 3 , and the optimized formula Ba 1.995 ZnS 2.82 :Eu 2+ 0.005 , I - 0.18 showed a potential application in solar spectral conversion for agricultural greenhouse and solar cell. Defect chemistry theory and crystal field theory provided insights into the key role of halide ions in enhancing green-excitation efficiency.

  15. SplitRacer - a new Semi-Automatic Tool to Quantify And Interpret Teleseismic Shear-Wave Splitting

    Science.gov (United States)

    Reiss, M. C.; Rumpker, G.

    2017-12-01

    We have developed a semi-automatic, MATLAB-based GUI to combine standard seismological tasks such as the analysis and interpretation of teleseismic shear-wave splitting. Shear-wave splitting analysis is widely used to infer seismic anisotropy, which can be interpreted in terms of lattice-preferred orientation of mantle minerals, shape-preferred orientation caused by fluid-filled cracks or alternating layers. Seismic anisotropy provides a unique link between directly observable surface structures and the more elusive dynamic processes in the mantle below. Thus, resolving the seismic anisotropy of the lithosphere/asthenosphere is of particular importance for geodynamic modeling and interpretations. The increasing number of seismic stations from temporary experiments and permanent installations creates a new basis for comprehensive studies of seismic anisotropy world-wide. However, the increasingly large data sets pose new challenges for the rapid and reliably analysis of teleseismic waveforms and for the interpretation of the measurements. Well-established routines and programs are available but are often impractical for analyzing large data sets from hundreds of stations. Additionally, shear wave splitting results are seldom evaluated using the same well-defined quality criteria which may complicate comparison with results from different studies. SplitRacer has been designed to overcome these challenges by incorporation of the following processing steps: i) downloading of waveform data from multiple stations in mseed-format using FDSNWS tools; ii) automated initial screening and categorizing of XKS-waveforms using a pre-set SNR-threshold; iii) particle-motion analysis of selected phases at longer periods to detect and correct for sensor misalignment; iv) splitting analysis of selected phases based on transverse-energy minimization for multiple, randomly-selected, relevant time windows; v) one and two-layer joint-splitting analysis for all phases at one station by

  16. Outage Analysis of Cooperative Transmission with Energy Harvesting Relay: Time Switching versus Power Splitting

    Directory of Open Access Journals (Sweden)

    Guanyao Du

    2015-01-01

    Full Text Available This paper investigates the multiuser transmission network with an energy harvesting (EH cooperative relay, where a source transmits independent information to multiple destinations with the help of an energy constrained relay. The relay can harvest energy from the radio frequency (RF signals transmitted from the source, and it helps the multiuser transmission only by consuming the harvested energy. By adopting the time switching and the power splitting relay receiver architectures, we firstly propose two protocols, the time switching cooperative multiuser transmission (TSCMT protocol and the power splitting cooperative multiuser transmission (PSCMT protocol, to enable the simultaneous information processing and EH at the relay for the system. To evaluate the system performance, we theoretically analyze the system outage probability for the two proposed protocols and then derive explicit expressions for each of them, respectively. Numerical results are provided to demonstrate the accuracy of our analytical results and reveal that compared with traditional noncooperative scheme our proposed protocols are green solutions to offer reliable communication and lower system outage probability without consuming additional energy. In particular, for the same transmit power at the source, the PSCMT protocol is superior to the TSCMT protocol to obtain lower system outage probability.

  17. Iterative support detection-based split Bregman method for wavelet frame-based image inpainting.

    Science.gov (United States)

    He, Liangtian; Wang, Yilun

    2014-12-01

    The wavelet frame systems have been extensively studied due to their capability of sparsely approximating piece-wise smooth functions, such as images, and the corresponding wavelet frame-based image restoration models are mostly based on the penalization of the l1 norm of wavelet frame coefficients for sparsity enforcement. In this paper, we focus on the image inpainting problem based on the wavelet frame, propose a weighted sparse restoration model, and develop a corresponding efficient algorithm. The new algorithm combines the idea of iterative support detection method, first proposed by Wang and Yin for sparse signal reconstruction, and the split Bregman method for wavelet frame l1 model of image inpainting, and more important, naturally makes use of the specific multilevel structure of the wavelet frame coefficients to enhance the recovery quality. This new algorithm can be considered as the incorporation of prior structural information of the wavelet frame coefficients into the traditional l1 model. Our numerical experiments show that the proposed method is superior to the original split Bregman method for wavelet frame-based l1 norm image inpainting model as well as some typical l(p) (0 ≤ p wavelet frame coefficients.

  18. Tangled up in mood : Exploring Panará split ergativity

    NARCIS (Netherlands)

    Bardagil-Mas, Bernat

    2015-01-01

    The two primary goals of this article are to present data concerning the mood-based alignment split that can be observed in Panará pronominal clitics and to put forward a tentative formal analysis that can capture the motivations of such phenomena in the grammar. This paper aims to explore an

  19. Deconstruction, G_2 Holonomy, and Doublet-Triplet Splitting

    OpenAIRE

    Witten, Edward

    2002-01-01

    We describe a mechanism for using discrete symmetries to solve the doublet-triplet splitting problem of four-dimensional supersymmetric GUT's. We present two versions of the mechanism, one via ``deconstruction,'' and one in terms of M-theory compactification to four dimensions on a manifold of G_2 holonomy.

  20. Split shielding plates in electrostatic sector analyzers and Wien filters

    Science.gov (United States)

    Yavor, Mikhail I.

    1995-09-01

    An analytical method is developed for calculation of the influence of the splitted shielding plates in inhomogeneous electrostatic sector analyzers and Wien filters on their electron optical properties. The method allows one to simplify considerably the choice of the mode of operation of the shielding plates needed to achieve a required electrostatic field distribution inside the analyzer.

  1. Split tensile strength of soilcrete blocks | Okere | Nigerian Journal of ...

    African Journals Online (AJOL)

    With the ever increasing problems associated with dredging of rivers to obtain river sand, reduced dependence on river sand should be encouraged by using alternative materials in block production. This work deals with the production of soilcrete blocks using readily available and affordable laterite. Split tensile strength of ...

  2. Signature splitting in two quasiparticle rotational bands of Ta

    Indian Academy of Sciences (India)

    2016-06-20

    Jun 20, 2016 ... ... of 182Ta are analysed within the framework of two-quasiparticle rotor model. The phase as well as magni- tude of the experimentally observed signature splitting in Kπ = 1+ band of 180Ta, which could not be explained in earlier calculations, is successfully reproduced. The conflict regarding placement of ...

  3. Split Hand and Foot Malformation | Salati | East and Central African ...

    African Journals Online (AJOL)

    East and Central African Journal of Surgery. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 16, No 2 (2011) >. Log in or Register to get access to full text downloads. Username, Password, Remember me, or Register. Split Hand and Foot Malformation. SA Salati ...

  4. Reconstruction of bilateral tibial aplasia and split hand-foot ...

    African Journals Online (AJOL)

    Background: Tibial aplasia is of heterogeneous aetiology, the majority of reports are sporadic. We describe the reconstruction procedures in two subjects - a daughter and father manifested autosomal dominant (AD) inheritance of the bilateral tibial aplasia and split hand-foot syndrome. Materials and Methods: ...

  5. Split calvarial graft and titanium mesh for reconstruction of post ...

    African Journals Online (AJOL)

    Background: The goal of cranioplasty is to achieve a lifelong, stable and structural reconstruction of the cranium covered by a healthy skin and scalp flap. We present two cases of large frontal bone defect following a accident.. Cases: We describe the utilization of autogenous local split calvarial graft and titanium mesh for ...

  6. Constructing General Orthogonal Fractional Factorial Split-Plot Designs

    NARCIS (Netherlands)

    Sartono, B.; Goos, P.; Schoen, E.

    2015-01-01

    While the orthogonal design of split-plot fractional factorial experiments has received much attention already, there are still major voids in the literature. First, designs with one or more factors acting at more than two levels have not yet been considered. Second, published work on nonregular

  7. Stride length asymmetry in split-belt locomotion

    NARCIS (Netherlands)

    Hoogkamer, W.; Bruijn, S.M.; Duysens, J.

    2013-01-01

    The number of studies utilizing a split-belt treadmill is rapidly increasing in recent years. This has led to some confusion regarding the definitions of reported gait parameters. The purpose of this paper is to clearly present the definitions of the gait parameters that are commonly used in

  8. Relations among the crack growth modes resulting from tensor splitting

    Czech Academy of Sciences Publication Activity Database

    Kafka, Vratislav

    2015-01-01

    Roč. 60, č. 4 (2015), s. 319-335 ISSN 0001-7043 Institutional support: RVO:68378297 Keywords : fracture mechanics * combination of crack-growth modes * non-local effect * tensor splitting Subject RIV: JL - Materials Fatigue, Friction Mechanics http://journal.it.cas.cz/60(15)4-Contents/60(15)4a.pdf

  9. The Case of Missing Solar Neutrinos with their Split Personalities

    Indian Academy of Sciences (India)

    The Case of Missing Solar Neutrinos with their Split Personalities. ~~~'<,. ~. The Case of Missing Solar Neutrinos ... general theory of relativity and the observed precession of the perihelion of Mercury was a great triumph ..... neutrino counting rate, by nearly a factor of 3 over the. SSM prediction, constitutes the solar neutrino ...

  10. Splitting and Projection: Drawing on Psychodynamics in Educational Psychology Practice

    Science.gov (United States)

    Pellegrini, Dario W.

    2010-01-01

    This paper reflects the author's journey into an area of psychology which is not dominant in Educational Psychology discourse, namely psychodynamic psychology. Two psychodynamic mechanisms, namely splitting and projection are explained, and then the author describes and critiques how these mechanisms have proved useful in his practice. Two case…

  11. Split-Framework in Mandibular Implant-Supported Prosthesis

    Directory of Open Access Journals (Sweden)

    Danny Omar Mendoza Marin

    2015-01-01

    Full Text Available During oral rehabilitation of an edentulous patient with an implant-supported prosthesis, mandibular flexure must be considered an important biomechanical factor when planning the metal framework design, especially if implants are installed posterior to the interforaminal region. When an edentulous mandible is restored with a fixed implant-supported prosthesis connected by a fixed full-arch framework, mandibular flexure may cause needless stress in the overall restorative system and lead to screw loosening, poor fit of prosthesis, loss of the posterior implant, and patient’s discomfort due to deformation properties of the mandible during functional movements. The use of a split-framework could decrease the stress with a precise and passive fit on the implants and restore a more natural functional condition of the mandible, helping in the longevity of the prosthesis. Therefore, the present clinical report describes the oral rehabilitation of an edentulous patient by a mandibular fixed implant-supported prosthesis with a split-framework to compensate for mandibular flexure. Clinical Significance. The present clinical report shows that the use of a split-framework reduced the risk of loss of the posterior implants or screws loosening with acceptable patient comfort over the period of a year. The split-framework might have compensated for the mandibular flexure during functional activities.

  12. Transient Splitting of Conoscopic Isogyres of a Uniaxial Nematic

    Science.gov (United States)

    Kim, Young-Ki; Senuk, Bohdan; Tortora, Luana; Sprunt, Samuel; Lehmann, Matthias; Lavrentovich, Oleg D.

    2012-02-01

    The phase identification is often based on conoscopic observations of homeotropic cells: A uniaxial nematic produces a pattern with crossed isogyres, while the biaxial nematic shows a split of isogyres. We demonstrate that the splitting of isogyres occurs even when the material remains in the uniaxial nematic phase. In particular, in the bent core material J35, splitting of isogyres is caused by change of the temperature. The effect is transient and the isogyres return to a uniaxial (crossed) configuration after a certain time that depends on sample thickness, temperature, and rate of temperature change; the time varies from a few seconds to tens of hours. The transient splitting is caused by the temperature-induced material flow that triggers a (uniaxial) director tilt in the cell. The flows and the director tilt are demonstrated by the CARS microscopy and fluorescent confocal polarizing microscopy (FCPM). This transient effect is general and can be observed even in E7 and 5CB. The effect should be considered in textural identifications of potential biaxial nematic materials.

  13. Mass Communication and Ticket Splitting in the 1972 General Election.

    Science.gov (United States)

    Atwood, L. Erwin; Sanders, Keith R.

    There is evidence of a growing trend toward ticket splitting, or independent voting patterns in all U.S. elections, especially in recent years. Independence of the electorate in 1972 was visible in the large Republican vote for President, during substantial voting for Democrats in Congress, and in gubernatorial elections. Analysis of mass media…

  14. Trellis plots as visual aids for analyzing split plot experiments

    DEFF Research Database (Denmark)

    Kulahci, Murat; Menon, Anil

    2017-01-01

    The analysis of split plot experiments can be challenging due to a complicated error structure resulting from restrictions on complete randomization. Similarly, standard visualization methods do not provide the insight practitioners desire to understand the data, think of explanations, generate h...

  15. A cyclic iterative method for solving multiple sets split feasibility ...

    African Journals Online (AJOL)

    (An iterative regularization method for the solution of the split feasibility problem in Banach spaces, Inverse Problems 24 (2008), 055008) and many important recent results in this direction. Mathematics Subject Classification (2010): 49J53, 65K10, 49M37, 90C25. Keywords: Bregman projection, strong convergence, metric ...

  16. Degloved foot sole successfully reconstructed with split thickness skin grafts

    NARCIS (Netherlands)

    Janssens, Loes; Holtslag, Herman R.; Schellekens, Pascal P A; Leenen, Luke P H

    2015-01-01

    Introduction The current opinion is that split thickness skin grafts are not suitable to reconstruct a degloved foot sole. The tissue is too fragile to carry full bodyweight; and therefore, stress lesions frequently occur. The treatment of choice is the reuse of the avulsed skin whenever possible,

  17. The split notochord syndrome with dorsal enteric fistula.

    Science.gov (United States)

    Hoffman, C H; Dietrich, R B; Pais, M J; Demos, D S; Pribram, H F

    1993-01-01

    Split notochord syndrome with dorsal enteric fistula is an extremely rare congenital anomaly that may be associated with meningomyelocele or meningocele, and genitourinary anomalies. This case presented with an additional finding of bladder exstrophy, raising the possibility of a relationship between this syndrome and the OEIS complex.

  18. Recent developments in solar H 2 generation from water splitting

    Indian Academy of Sciences (India)

    Hydrogen production from water and sunlight through photocatalysis could become one of the channels, in the not-so-distant future, to meet a part of ever growing energy demands. However, accomplishing solar water splitting through semiconductor particulate photocatalysis seems to be the 'Holy Grail' problem of science.

  19. Fundaments of transport equation splitting and the eigenvalue problem

    International Nuclear Information System (INIS)

    Stancic, V.

    2000-01-01

    In order to remove some singularities concerning the boundary conditions of one dimensional transport equation, a split form of transport equation describing the forward i.e. μ≥0, and a backward μ<0 directed neutrons is being proposed here. The eigenvalue problem has also been considered here (author)

  20. Split-mouth design in Paediatric Dentistry clinical trials.

    Science.gov (United States)

    Pozos-Guillén, A; Chavarría-Bolaños, D; Garrocho-Rangel, A

    2017-03-01

    The aim of this article was to describe the essential concepts of the split-mouth design, its underlying assumptions, advantages, limitations, statistical considerations, and possible applications in Paediatric Dentistry clinical investigation. In Paediatric Dentistry clinical investigation, and as part of randomised controlled trials, the split-mouth design is commonly used. The design is characterised by subdividing the child's dentition into halves (right and left), where two different treatment modalities are assigned to one side randomly, in order to allow further outcome evaluation. Each participant acts as their own control by making within- patient rather than between-patient comparisons, thus diminishing inter-subject variability and increasing study accuracy and power. However, the main problem with this design comprises the potential contamination of the treatment effect from one side to the other, or the "carry-across effect"; likewise, this design is not indicated when the oral disease to be treated is not symmetrically distributed (e.g. severity) in the mouth of children. Thus, in spite of its advantages, the split-mouth design can only be applied in a limited number of strictly selected cases. In order to obtain valid and reliable data from split mouth design studies, it is necessary to evaluate the risk of carry-across effect as well as to carefully analise and select adequate inclusion criteria, sample-size calculation and method of statistical analysis.

  1. Visible-light-induced water splitting on a chip

    NARCIS (Netherlands)

    Zoontjes, M.G.C.

    2015-01-01

    In this thesis, a photoelectrochemical water splitting cell concept is discussed, based on a combination of semiconductors comprising a Z-scheme. The motivation for the development of the cell is that in the future a transition will take place from a fossil fuel-based economy, to an economy based on

  2. Higgs, Binos and Gluinos: Split Susy within Reach

    Energy Technology Data Exchange (ETDEWEB)

    Alves, Daniele S.M.; Izaguirre, Eder; /SLAC /Stanford U., Phys. Dept.; Wacker, Jay G.; /SLAC /Stanford U., ITP

    2012-09-14

    Recent results from the LHC for the Higgs boson with mass between 142 GeV {approx}< m{sub h{sup 0}} {approx}< 147 GeV points to PeV-scale Split Supersymmetry. This article explores the consequences of a Higgs mass in this range and possible discovery modes for Split Susy. Moderate lifetime gluinos, with decay lengths in the 25 {micro}m to 10 yr range, are its imminent smoking gun signature. The 7TeV LHC will be sensitive to the moderately lived gluinos and trilepton signatures from direct electroweakino production. Moreover, the dark matter abundance may be obtained from annihilation through an s-channel Higgs resonance, with the LSP almost purely bino and mass m{sub {chi}{sub 1}{sup 0}} {approx_equal} 70 GeV. The Higgs resonance region of Split Susy has visible signatures in dark matter direct and indirect detection and electric dipole moment experiments. If the anomalies go away, the majority of Split Susy parameter space will be excluded.

  3. On split Lie algebras with symmetric root systems

    Indian Academy of Sciences (India)

    , Spain. E-mail: ajesus.calderon@uca.es. MS received 24 May 2007. Abstract. We develop techniques of connections of roots for split Lie algebras with symmetric root systems. We show that any of such algebras L is of the form L = U +. ∑.

  4. Reduction of Biomass Moisture by Crushing/Splitting - A Concept

    Science.gov (United States)

    Paul E. Barnett; Donald L. Sirois; Colin Ashmore

    1986-01-01

    A biomass crusher/splitter concept is presented as a possible n&ant of tsafntainfng rights-of-way (ROW) or harvesting energy wood plantations. The conceptual system would cut, crush, and split small woody biomass leaving it in windrows for drying. A subsequent operation would bale and transport the dried material for use as an energy source. A survey of twenty...

  5. Robustness of the Rabi Splitting under Nonlocal Corrections in Plexcitonics

    DEFF Research Database (Denmark)

    Tserkezis, Christos; Wubs, Martijn; Mortensen, N. Asger

    2018-01-01

    , the influence of nonlocality is rather limited, as in most occasions the width of the Rabi splitting remains largely unaffected and the two hybrid modes are well distinguishable. We discuss how this behavior can be understood in view of the popular coupled-harmonic-oscillator model, while we also provide...

  6. Ductless Mini-Split Heat Pump Comfort Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Roth, K.; Sehgal, N.; Akers, C.

    2013-03-01

    Field tests were conducted in two homes in Austin, TX to evaluate the comfort performance of ductless mini-split heat pumps (DMSHPs), measuring temperature and relative humidity measurements in four rooms in each home before and after retrofitting a central HVAC system with DMSHPs.

  7. Roadmap on solar water splitting: current status and future prospects

    Science.gov (United States)

    Chu, Sheng; Li, Wei; Yan, Yanfa; Hamann, Thomas; Shih, Ishiang; Wang, Dunwei; Mi, Zetian

    2017-09-01

    Artificial photosynthesis via solar water splitting provides a promising approach to storing solar energy in the form of hydrogen on a global scale. However, an efficient and cost-effective solar hydrogen production system that can compete with traditional methods using fossil fuels is yet to be developed. A photoelectrochemical (PEC) tandem cell consisting of a p-type photocathode and an n-type photoanode, with the photovoltage provided by the two photoelectrodes, is an attractive route to achieve highly efficient unassisted water splitting at a low cost. In this article, we provide an overview of recent developments of semiconductor materials, including metal oxides, nitrides, chalcogenides, Si, III-V compounds and organics, either as photocathodes or photoanodes for water reduction and oxidation, respectively. In addition, recent efforts in constructing a PEC tandem system for unassisted water splitting are outlined. The importance of developing a single-photon photocathode and photoanode that can deliver high photocurrent in the low bias region for efficient PEC tandem system is highlighted. Finally, we discuss the future development of photoelectrode materials, and viable solutions to realize highly efficient PEC water splitting device for practical applications.

  8. Recent developments in solar H2 generation from water splitting

    Indian Academy of Sciences (India)

    Abstract. Hydrogen production from water and sunlight through photocatalysis could become one of the channels, in the not-so-distant future, to meet a part of ever growing energy demands. However, accomplish- ing solar water splitting through semiconductor particulate photocatalysis seems to be the 'Holy Grail' prob-.

  9. The Case of Missing Solar Neutrinos with their Split Personalities

    Indian Academy of Sciences (India)

    The Case of Missing Solar Neutrinos with their Split Personalities. S M Chitre is a Senior. Professor at Tata Institute of Fundamental Research,. Mumbai. His research interests are in the areas of solar physics, physics and astrophysics of condensed objects and gravitational lenses. Keywords. Neutrino. Sun, solar structure.

  10. Modelling of Split Condenser Heat Pump: Optimization and Exergy Analysis

    DEFF Research Database (Denmark)

    Christensen, Stefan Wuust; Elmegaard, Brian; Markussen, Wiebke Brix

    2017-01-01

    This paper presents a numerical study of a split condenser heat pump (SCHP). The SCHP setup differs from a traditional heat pump (THP) setup in the way that two separate water streams on the secondary side of the condenser are heated in parallel to different temperature levels, whereas only one s...

  11. On Split Lie Algebras with Symmetric Root Systems

    Indian Academy of Sciences (India)

    ... and any I j a well described ideal of , satisfying [ I j , I k ] = 0 if j ≠ k . Under certain conditions, the simplicity of is characterized and it is shown that is the direct sum of the family of its minimal ideals, each one being a simple split Lie algebra with a symmetric root system and having all its nonzero roots connected.

  12. On split Lie algebras with symmetric root systems

    Indian Academy of Sciences (India)

    ideal of L, satisfying [Ij ,Ik] = 0 if j = k. Under certain conditions, the simplicity of L is characterized and it is shown that L is the direct sum of the family of its minimal ideals, each one being a simple split Lie algebra with a symmetric root system and having all its nonzero roots connected. Keywords. Infinite dimensional Lie ...

  13. On split Lie algebras with symmetric root systems

    Indian Academy of Sciences (India)

    ... family of its minimal ideals, each one being a simple split Lie algebra with a symmetric root system and having all its nonzero roots connected. Author Affiliations. Antonio J Calderón Martín1. Departamento de Matemáticas, Universidad de Cádiz, 11510 Puerto Real, Cádiz, Spain. Dates. Manuscript received: 24 May 2007 ...

  14. Phosphoinositide signaling.

    Science.gov (United States)

    Boss, Wendy F; Im, Yang Ju

    2012-01-01

    "All things flow and change…even in the stillest matter there is unseen flux and movement." Attributed to Heraclitus (530-470 BC), from The Story of Philosophy by Will Durant. Heraclitus, a Greek philosopher, was thinking on a much larger scale than molecular signaling; however, his visionary comments are an important reminder for those studying signaling today. Even in unstimulated cells, signaling pathways are in constant metabolic flux and provide basal signals that travel throughout the organism. In addition, negatively charged phospholipids, such as the polyphosphorylated inositol phospholipids, provide a circuit board of on/off switches for attracting or repelling proteins that define the membranes of the cell. This template of charged phospholipids is sensitive to discrete changes and metabolic fluxes-e.g., in pH and cations-which contribute to the oscillating signals in the cell. The inherent complexities of a constantly fluctuating system make understanding how plants integrate and process signals challenging. In this review we discuss one aspect of lipid signaling: the inositol family of negatively charged phospholipids and their functions as molecular sensors and regulators of metabolic flux in plants.

  15. Use of computed tomography assessed kidney length to predict split renal GFR in living kidney donors

    International Nuclear Information System (INIS)

    Gaillard, Francois; Fournier, Catherine; Leon, Carine; Legendre, Christophe; Pavlov, Patrik; Tissier, Anne-Marie; Correas, Jean-Michel; Harache, Benoit; Hignette, Chantal; Weinmann, Pierre; Eladari, Dominique; Timsit, Marc-Olivier; Mejean, Arnaud; Friedlander, Gerard; Courbebaisse, Marie; Houillier, Pascal

    2017-01-01

    Screening of living kidney donors may require scintigraphy to split glomerular filtration rate (GFR). To determine the usefulness of computed tomography (CT) to split GFR, we compared scintigraphy-split GFR to CT-split GFR. We evaluated CT-split GFR as a screening test to detect scintigraphy-split GFR lower than 40 mL/min/1.73 m 2 /kidney. This was a monocentric retrospective study on 346 potential living donors who had GFR measurement, renal scintigraphy, and CT. We predicted GFR for each kidney by splitting GFR using the following formula: Volume-split GFR for a given kidney = measured GFR*[volume of this kidney/(volume of this kidney + volume of the opposite kidney)]. The same formula was used for length-split GFR. We compared length- and volume-split GFR to scintigraphy-split GFR at donation and with a 4-year follow-up. A better correlation was observed between length-split GFR and scintigraphy-split GFR (r = 0.92) than between volume-split GFR and scintigraphy-split GFR (r = 0.89). A length-split GFR threshold of 45 mL/min/1.73 m 2 /kidney had a sensitivity of 100 % and a specificity of 75 % to detect scintigraphy-split GFR less than 40 mL/min/1.73 m 2 /kidney. Both techniques with their respective thresholds detected living donors with similar eGFR evolution during follow-up. Length-split GFR can be used to detect patients requiring scintigraphy. (orig.)

  16. Use of computed tomography assessed kidney length to predict split renal GFR in living kidney donors

    Energy Technology Data Exchange (ETDEWEB)

    Gaillard, Francois; Fournier, Catherine; Leon, Carine; Legendre, Christophe [Paris Descartes University, AP-HP, Hopital Necker-Enfants Malades, Renal Transplantation Department, Paris (France); Pavlov, Patrik [Linkoeping University, Linkoeping (Sweden); Tissier, Anne-Marie; Correas, Jean-Michel [Paris Descartes University, AP-HP, Hopital Necker-Enfants Malades, Radiology Department, Paris (France); Harache, Benoit; Hignette, Chantal; Weinmann, Pierre [Paris Descartes University, AP-HP, Hopital Europeen Georges Pompidou, Nuclear Medicine Department, Paris (France); Eladari, Dominique [Paris Descartes University, and INSERM, Unit 970, AP-HP, Hopital Europeen Georges Pompidou, Physiology Department, Paris (France); Timsit, Marc-Olivier; Mejean, Arnaud [Paris Descartes University, AP-HP, Hopital Europeen Georges Pompidou, Urology Department, Paris (France); Friedlander, Gerard; Courbebaisse, Marie [Paris Descartes University, and INSERM, Unit 1151, AP-HP, Hopital Europeen Georges Pompidou, Physiology Department, Paris (France); Houillier, Pascal [Paris Descartes University, INSERM, Unit umrs1138, and CNRS Unit erl8228, AP-HP, Hopital Europeen Georges Pompidou, Physiology Department, Paris (France)

    2017-02-15

    Screening of living kidney donors may require scintigraphy to split glomerular filtration rate (GFR). To determine the usefulness of computed tomography (CT) to split GFR, we compared scintigraphy-split GFR to CT-split GFR. We evaluated CT-split GFR as a screening test to detect scintigraphy-split GFR lower than 40 mL/min/1.73 m{sup 2}/kidney. This was a monocentric retrospective study on 346 potential living donors who had GFR measurement, renal scintigraphy, and CT. We predicted GFR for each kidney by splitting GFR using the following formula: Volume-split GFR for a given kidney = measured GFR*[volume of this kidney/(volume of this kidney + volume of the opposite kidney)]. The same formula was used for length-split GFR. We compared length- and volume-split GFR to scintigraphy-split GFR at donation and with a 4-year follow-up. A better correlation was observed between length-split GFR and scintigraphy-split GFR (r = 0.92) than between volume-split GFR and scintigraphy-split GFR (r = 0.89). A length-split GFR threshold of 45 mL/min/1.73 m{sup 2}/kidney had a sensitivity of 100 % and a specificity of 75 % to detect scintigraphy-split GFR less than 40 mL/min/1.73 m{sup 2}/kidney. Both techniques with their respective thresholds detected living donors with similar eGFR evolution during follow-up. Length-split GFR can be used to detect patients requiring scintigraphy. (orig.)

  17. Methane splitting in the K plant at Heydebreck

    Energy Technology Data Exchange (ETDEWEB)

    1942-03-09

    This report consisted of two major topics. The first was methane splitting in equipment for gas for distant transmission. The amount to be split was 3500 m/sup 3//hr methane per system. The temperature in the converter outlet was 850/sup 0/C and the methane was preheated to 650/sup 0/C. The results of this showed oxygen requirements to be 0.487 m/sup 3//m/sup 3/ of methane, steam requirements to be 0.529 kg/m/sup 3/ of methane, condensate requirements to be 0.518 kg/m/sup 3/ of methane, and cooling-water requirements to be 16 kg/m/sup 3/ of methane. The second topic was methane splitting in equipment for long-distance gas with additional indirect cooling. A summary showed the oxygen requirements to be 0.487 m/sup 3//m/sup 3/ of methane, steam requirements to be 0.107 kg/m/sup 3/ of methane, condensate requirements to be 0.526 kg/m/sup 3/ of methane, and cooling-water requirements to be 9.6 kg/m/sup 3/ of methane. The items discussed for each topic included calculations of methane converters, which included oxygen requirements and a heat balance of the converter; cooling of the split gas, which included heat content of the split gas at the catalyst converter outlet and heat exchangers; and the cooler-vaporizer system, which included a heat balance of the water circuit, determination of the amount of water in the cooler-vaporizer, and final cooling. 3 figures.

  18. Exciton Splitting of Adsorbed and Free 4-Nitroazobenzene Dimers: A Quantum Chemical Study.

    Science.gov (United States)

    Titov, Evgenii; Saalfrank, Peter

    2016-05-19

    Molecular photoswitches such as azobenzenes, which undergo photochemical trans ↔ cis isomerizations, are often mounted for possible applications on a surface and/or surrounded by other switches, for example, in self-assembled monolayers. This may suppress the isomerization cross section due to possible steric reasons, or, as recently speculated, by exciton coupling to neighboring switches, leading to ultrafast electronic quenching (Gahl et al., J. Am. Chem. Soc. 2010, 132, 1831). The presence of exciton coupling has been anticipated from a blue shift of the optical absorption band, compared to molecules in solution. From the theory side the need arises to properly analyze and quantify the change of absorption spectra of interacting and adsorbed switches. In particular, suitable methods should be identified, and effects of intermolecule and molecule-surface interactions on spectra should be disentangled. In this paper by means of time-dependent Hartree-Fock (TD-HF), various flavors of time-dependent density functional theory (TD-DFT), and the correlated wave function based coupled-cluster (CC2) method we investigated the 4-nitroazobenzene molecule as an example: The low-lying singlet excited states in the isolated trans monomer and dimer as well as their composites with a silicon pentamantane nanocluster, which serves also as a crude model for a silicon surface, were determined. As most important results we found that (i) HF, CC2, range-separated density functionals, or global hybrids with large amount of exact exchange are able to describe exciton (Davydov) splitting properly, while hybrids with small amount of exact exchange fail producing spurious charge transfer. (ii) The exciton splitting in a free dimer would lead to a blue shift of the absorption signal; however, this effect is almost nullified or even overcompensated by the shift arising from van der Waals interactions between the two molecules. (iii) Adsorption on the Si "surface" leads to a further

  19. Subsignal-based denoising from piecewise linear or constant signal

    Science.gov (United States)

    Jalil, Bushra; Beya, Ouadi; Fauvet, Eric; Laligant, Olivier

    2011-11-01

    In the present work, a novel signal denoising technique for piecewise constant or linear signals is presented termed as ``signal split.'' The proposed method separates the sharp edges or transitions from the noise elements by splitting the signal into different parts. Unlike many noise removal techniques, the method works only in the nonorthogonal domain. The new method utilizes Stein unbiased risk estimate (SURE) to split the signal, Lipschitz exponents to identify noise elements, and a polynomial fitting approach for the sub signal reconstruction. At the final stage, merging of all parts yield in the fully denoised signal at a very low computational cost. Statistical results are quite promising and performs better than the conventional shrinkage methods in the case of different types of noise, i.e., speckle, Poisson, and white Gaussian noise. The method has been compared with the state of the art SURE-linear expansion of thresholds denoising technique as well and performs equally well. The method has been extended to the multisplitting approach to identify small edges which are difficult to identify due to the mutual influence of their adjacent strong edges.

  20. Synthesis of In2S3 nanoplates and their self-assembly into superlattices.

    Science.gov (United States)

    Zhong, Haizheng; Ye, Mingfu; Zhou, Yi; Yang, Chunhe; Li, Yongfang

    2007-12-01

    Ultrathin nanoplates of beta-phase semiconductor In2S3 with the diameter of 50 - 80 nm and a thickness of 1.85 nm were synthesized via a simple hot injection solution method with Hexadecylamine (HDA) as ligand, and the nanoplates self-assembled into superlattices by face to face stacking during evaporation of the solvent. The nanoplates and the assembled superlattices were characterized by XRD, TEM, HRTEM, XPS etc. The TEM and XRD results display that the nanocrystals are highly crystalline, hexagonal shape, and uniform in thickness. A strong quantum confinement effect of the 2D nanoplates was observed from the UV-Vis and PL spectra for the first time in the In2S3 nanoplates. A possible mechanism of the synthesis and assembly was proposed.

  1. Sn Doped In2S3 Films Elaborated by Spray Technique

    Directory of Open Access Journals (Sweden)

    M. KRAINI

    2014-05-01

    Full Text Available Tin doped In2S3 films were grown by the chemical spray pyrolysis (CSP method using the pneumatic spray set-up and compressed air as a carrier gas. The spraying solution contained indium chloride (InCl3, thiourea [CS(NH22] and (SnCl4 at a molar ratio of S/In = 2.5. The deposition was carried out at 350 °C on glass substrates. The Sn doping level was changed with Sn/In = 0-8 % in solution. The effect of Sn concentration on electrical, optical and structural properties of In2S3:Sn thin films have been investigated.

  2. Solution-processed In2S3 buffer layer for chalcopyrite thin film solar cells

    Directory of Open Access Journals (Sweden)

    Wang Lan

    2016-01-01

    Full Text Available We report a route to deposit In2S3 thin films from air-stable, low-cost molecular precursor inks for Cd-free buffer layers in chalcopyrite-based thin film solar cells. Different precursor compositions and processing conditions were studied to define a reproducible and robust process. By adjusting the ink properties, this method can be applied in different printing and coating techniques. Here we report on two techniques, namely spin-coating and inkjet printing. Active area efficiencies of 12.8% and 12.2% have been achieved for In2S3-buffered solar cells respectively, matching the performance of CdS-buffered cells prepared with the same batch of absorbers.

  3. Solution-processed In2S3 buffer layer for chalcopyrite thin film solar cells

    Science.gov (United States)

    Wang, Lan; Lin, Xianzhong; Ennaoui, Ahmed; Wolf, Christian; Lux-Steiner, Martha Ch.; Klenk, Reiner

    2016-02-01

    We report a route to deposit In2S3 thin films from air-stable, low-cost molecular precursor inks for Cd-free buffer layers in chalcopyrite-based thin film solar cells. Different precursor compositions and processing conditions were studied to define a reproducible and robust process. By adjusting the ink properties, this method can be applied in different printing and coating techniques. Here we report on two techniques, namely spin-coating and inkjet printing. Active area efficiencies of 12.8% and 12.2% have been achieved for In2S3-buffered solar cells respectively, matching the performance of CdS-buffered cells prepared with the same batch of absorbers.

  4. Gate-tunable transport characteristics of Bi2S3 nanowire transistors

    Science.gov (United States)

    Kilcoyne, Colin; Ali, Ahmed H.; Alsaqqa, Ali M.; Rahman, Ajara A.; Whittaker-Brooks, Luisa; Sambandamurthy, Ganapathy

    2018-02-01

    Electrical transport and resistance noise spectroscopy measurements are performed on individual, single crystalline Bi2S3 nanowires in the field-effect geometry. The nanowires exhibit n-type conduction and device characteristics such as activation energy, ON/OFF ratio, and mobility are calculated over a temperature range of 120-320 K and at several bias values. The noise magnitude is measured between 0.01 and 5 Hz at several gate voltages as the device turns from it's OFF to ON state. The presence of mid-gap states which act as charge traps within the band gap can potentially explain the observed transport characteristics. Sulfur vacancies are the likely origin of these mid-gap states which makes Bi2S3 nanowires appealing for defect engineering as a means to enhance its optoelectronic properties and also to better understand the important role of defects in nanoscale semiconductors.

  5. Pulsed laser deposition from ZnS and Cu2SnS3 multicomponent targets

    International Nuclear Information System (INIS)

    Ettlinger, Rebecca Bolt; Cazzaniga, Andrea; Canulescu, Stela; Pryds, Nini; Schou, Jørgen

    2015-01-01

    Thin films of ZnS and Cu 2 SnS 3 have been produced by pulsed laser deposition (PLD), the latter for the first time. The effect of fluence and deposition temperature on the structure and the transmission spectrum as well as the deposition rate has been investigated, as has the stoichiometry of the films transferred from target to substrate. Elemental analysis by energy dispersive X-ray spectroscopy indicates lower S and Sn content in Cu 2 SnS 3 films produced at higher fluence, whereas this trend is not seen in ZnS. The deposition rate of the compound materials measured in atoms per pulse is considerably larger than that of the individual metals, Zn, Cu, and Sn

  6. Design of Sb2S3 nanorod-bundles: imperfect oriented attachment

    Science.gov (United States)

    Lu, Qifei; Zeng, Haibo; Wang, Zhenyang; Cao, Xueli; Zhang, Lide

    2006-05-01

    The large scale formation of uniform Sb2S3 nanorod-bundles has been achieved via a simple and mild hydrothermal approach with the assistance of polyvinylpyrrolidone. By closely inspecting the growth process and the crystallographic analysis of as-synthesized products, conclusive evidence has been provided to show that the growth mechanism of such nanorod-bundles is imperfect oriented attachment. The anisotropic adsorption of polyvinylpyrrolidone at the different surfaces of Sb2S3 nanocrystals assists the one-dimensional preferential growth; it is just the misorientations that result in the nanorod-based superstructures. Moreover, the hydrothermal treatment time plays a crucial role, and can be used as the parameter to control the size and morphology of the bundles. This simple approach promises future large-scale controlled synthesis of various nanobody-based superstructures for many important applications in nanotechnology.

  7. Electron irradiation induced reduction of the permittivity in chalcogenide glass (As2S3) thin film

    KAUST Repository

    San Roman Alerigi, Damian

    2013-01-01

    In this paper, we investigate the effect of electron beam irradiation on the dielectric properties of As 2 S 3 chalcogenide glass. By means of low-loss electron energy loss spectroscopy, we derive the permittivity function, its dispersive relation, and calculate the refractive index and absorption coefficients under the constant permeability approximation. The measured and calculated results show a heretofore unseen phenomenon: a reduction in the permittivity of ? 40 %. Consequently a reduction of the refractive index of 20%, hence, suggests a conspicuous change in the optical properties of the material under irradiation with a 300 keV electron beam. The plausible physical phenomena leading to these observations are discussed in terms of the homopolar and heteropolar bond dynamics under high energy absorption. The reported phenomena, exhibited by As 2 S 3-thin film, can be crucial for the development of photonics integrated circuits using electron beam irradiation method. © 2013 American Institute of Physics.

  8. Programming Amazon Web Services S3, EC2, SQS, FPS, and SimpleDB

    CERN Document Server

    Murty, James

    2009-01-01

    With this book, you'll learn how companies can take advantage of Amazon Web Services (AWS) to rent" computing power, data storage and bandwidth on Amazon's vast network infrastructure. Programming Amazon Web Services gives developers the background and technical detail they need for using Amazon's subscription-based Simple Storage Service (S3), Elastic Compute Cloud (EC2), Simple Queue Service (SQS), Flexible Payments Service (FPS), and SimpleDB to build web-scale business applications. "

  9. Solution-processed In2S3 buffer layer for chalcopyrite thin film solar cells

    OpenAIRE

    Wang Lan; Lin Xianzhong; Ennaoui Ahmed; Wolf Christian; Lux-Steiner Martha Ch.; Klenk Reiner

    2016-01-01

    We report a route to deposit In2S3 thin films from air-stable, low-cost molecular precursor inks for Cd-free buffer layers in chalcopyrite-based thin film solar cells. Different precursor compositions and processing conditions were studied to define a reproducible and robust process. By adjusting the ink properties, this method can be applied in different printing and coating techniques. Here we report on two techniques, namely spin-coating ...

  10. Chemical spray pyrolysis of β-In2S3 thin films deposited at different temperatures

    Science.gov (United States)

    Sall, Thierno; Marí Soucase, Bernabé; Mollar, Miguel; Hartitti, Bouchaib; Fahoume, Mounir

    2015-01-01

    In2S3 thin films were deposited onto indium tin oxide-coated glass substrates by chemical spray pyrolysis while keeping the substrates at different temperatures. The structures of the sprayed In2S3 thin films were characterized by X-ray diffraction (XFD). The quality of the thin films was determined by Raman spectroscopy. Scanning electron microscopy (SEM) and atomic force microscopy were used to explore the surface morphology and topography of the thin films, respectively. The optical band gap was determined based on optical transmission measurements. The indium sulfide phase exhibited a preferential orientation in the (0, 0, 12) crystallographic direction according to the XRD analysis. The phonon vibration modes determined by Raman spectroscopy also confirmed the presence of the In2S3 phase in our samples. According to SEM, the surface morphologies of the films were free of defects. The optical band gap energy varied from 2.82 eV to 2.95 eV.

  11. The total angular momentum algebra related to the S3 Dunkl Dirac equation

    Science.gov (United States)

    De Bie, Hendrik; Oste, Roy; Van der Jeugt, Joris

    2018-02-01

    We consider the symmetry algebra generated by the total angular momentum operators, appearing as constants of motion of the S3 Dunkl Dirac equation. The latter is a deformation of the Dirac equation by means of Dunkl operators, in our case associated to the root system A2, with corresponding Weyl group S3, the symmetric group on three elements. The explicit form of the symmetry algebra in this case is a one-parameter deformation of the classical total angular momentum algebra so(3) , incorporating elements of S3. This was obtained using recent results on the symmetry algebra for a class of Dirac operators, containing in particular the Dirac-Dunkl operator for arbitrary root system. For this symmetry algebra, we classify all finite-dimensional, irreducible representations and determine the conditions for the representations to be unitarizable. The class of unitary irreducible representations admits a natural realization acting on a representation space of eigenfunctions of the Dirac Hamiltonian. Using a Cauchy-Kowalevski extension theorem we obtain explicit expressions for these eigenfunctions in terms of Jacobi polynomials.

  12. Supercontinuum generation and analysis in extruded suspended-core As2S3 chalcogenide fibers

    Science.gov (United States)

    Si, Nian; Sun, Lihong; Zhao, Zheming; Wang, Xunsi; Zhu, Qingde; Zhang, Peiqing; Liu, Shuo; Pan, Zhanghao; Liu, Zijun; Dai, Shixun; Nie, Qiuhua

    2018-02-01

    Compared with the traditional fluoride fibers and tellurite fibers that can work in the near-infrared region, suspended-core fibers based on chalcogenide glasses have wider transmitting regions and higher nonlinear coefficients, thus the mid-infrared supercontinuum generations can be achieved easily. Rather than adopting the traditional fabrication technique of hole-drilling and air filling, we adopted a totally novel extrusion technique to fabricate As2S3 suspended-core fibers with four holes, and its mid-infrared supercontinuum generation was investigated systematically by integrating theoretical simulation and empirical results. The generalized nonlinear SchrÖdinger equation was used to simulate the supercontinuum generation in the As2S3 suspended-core fibers. The simulated supercontinuum generation in the As2S3 suspended-core fibers with different pump wavelengths (2-5 µm), increasing powers (0.3-4 kW), and various fiber lengths (1-50 cm) was obtained by a simulative software, MATLAB. The experimental results of supercontinuum generation via femtosecond optical parametric amplification (OPA) were recorded by changing fiber lengths (5-25 cm), pump wavelengths (2.9-5 µm), and pump powers (10-200 kW). The simulated consulting spectra are consistent with the experimental results of supercontinuum generation only if the fiber loss is sufficiently low.

  13. The Sim-SEQ Project: Comparison of Selected Flow Models for the S-3 Site

    Energy Technology Data Exchange (ETDEWEB)

    Mukhopadhyay, Sumit; Doughty, Christine A.; Bacon, Diana H.; Li, Jun; Wei, Lingli; Yamamoto, Hajime; Gasda, Sarah E.; Hosseini, Seyyed; Nicot, Jean-Philippe; Birkholzer, Jens

    2015-05-23

    Sim-SEQ is an international initiative on model comparison for geologic carbon sequestration, with an objective to understand and, if possible, quantify model uncertainties. Model comparison efforts in Sim-SEQ are at present focusing on one specific field test site, hereafter referred to as the Sim-SEQ Study site (or S-3 site). Within Sim-SEQ, different modeling teams are developing conceptual models of CO2 injection at the S-3 site. In this paper, we select five flow models of the S-3 site and provide a qualitative comparison of their attributes and predictions. These models are based on five different simulators or modeling approaches: TOUGH2/EOS7C, STOMP-CO2e, MoReS, TOUGH2-MP/ECO2N, and VESA. In addition to model-to-model comparison, we perform a limited model-to-data comparison, and illustrate how model choices impact model predictions. We conclude the paper by making recommendations for model refinement that are likely to result in less uncertainty in model predictions.

  14. Crystallized InBiS3 thin films with enhanced optoelectronic properties

    Science.gov (United States)

    Ali, N.; Hussain, Arshad; Ahmed, R.; Omar, M. Firdaus Bin; Sultan, M.; Fu, Yong Qing

    2018-04-01

    In this paper, a one-step thermal evaporation approach was used for fabrication of indium bismuth sulphide thin films, and the synergetic effects of co-evaporation of two sources (indium granules and Bi2S3 powders) were investigated using different characterization techniques. X-ray diffraction (XRD) analysis confirmed the crystalline orthorhombic structure for the post-annealed samples. Surface roughness and crystal size of the obtained film samples were increased with increasing annealing temperatures. Analysis using X-ray photoelectron spectroscopy showed the formation of the InBiS3 structure for the obtained films, which is also confirmed by the XRD results. The optical absorption coefficient value of the annealed samples was found to be in the order of 105 cm-1 in the visible region of the solar spectrum. The optical band gap energy and electrical resistivity of the fabricated samples were observed to decrease (from 2.2 to 1.3 eV, and from 0.3 to 0.01 Ω-cm, respectively) with increasing annealing temperatures (from 200 to 350 °C), indicating the suitability of the prepared InBiS3 thin films for solar cell applications.

  15. Silver environment and covalent network rearrangement in GeS3–Ag glasses

    International Nuclear Information System (INIS)

    Rátkai, L; Jóvári, P; Kaban, I; Wágner, T; Kolář, J; Valková, S; Voleská, Iva; Beuneu, B

    2013-01-01

    The structure of Ag-doped GeS 3 glasses (0, 15, 20, 25 at.% Ag) was investigated by diffraction techniques and extended x-ray absorption fine structure measurements. Structural models were obtained by fitting the experimental datasets simultaneously by the reverse Monte Carlo simulation technique. It is observed that Ge has mostly S neighbours in GeS 3 , but Ge–Ge bonds appear already at 15% Ag content. Sulfur has ∼2 S/Ge neighbours over the whole concentration range, while the S–Ag coordination number increases with increasing Ag content. Ag–Ag pairs can already be found at 15% Ag. The Ag–S mean coordination number changes from 2.17 ± 0.2 to 2.86 ± 0.2 between 15% and 25% Ag content. Unlike the As–S network in AsS 2 –25Ag glass, the Ge–S network is not fragmented upon Ag-doping of GeS 3 glass. (paper)

  16. Reference results for time-like evolution up to $\\mathcal{O}(\\alpha_s^3)$

    CERN Document Server

    Bertone, Valerio; Nocera, Emanuele R.

    2015-01-01

    We present high-precision numerical results for time-like Dokshitzer-Gribov-Lipatov-Altarelli-Parisi evolution in the $\\overline{\\rm MS}$ factorisation scheme, for the first time up to next-to-next-to-leading order accuracy in quantum chromodynamics. First, we scrutinise the analytical expressions of the splitting functions available in the literature, in both x and N space, and check their mutual consistency. Second, we implement time-like evolution in two publicly available, entirely independent and conceptually different numerical codes, in x and N space respectively: the already existing APFEL code, which has been updated with time-like evolution, and the new MELA code, which has been specifically developed to perform the study in this work. Third, by means of a model for fragmentation functions, we provide results for the evolution in different factorisation schemes, for different ratios between renormalisation and factorisation scales and at different final scales. Our results are collected in the forma...

  17. A structure-preserving split finite element discretization of the split 1D linear shallow-water equations

    Science.gov (United States)

    Bauer, Werner; Behrens, Jörn

    2017-04-01

    We present a locally conservative, low-order finite element (FE) discretization of the covariant 1D linear shallow-water equations written in split form (cf. tet{[1]}). The introduction of additional differential forms (DF) that build pairs with the original ones permits a splitting of these equations into topological momentum and continuity equations and metric-dependent closure equations that apply the Hodge-star. Our novel discretization framework conserves this geometrical structure, in particular it provides for all DFs proper FE spaces such that the differential operators (here gradient and divergence) hold in strong form. The discrete topological equations simply follow by trivial projections onto piecewise constant FE spaces without need to partially integrate. The discrete Hodge-stars operators, representing the discretized metric equations, are realized by nontrivial Galerkin projections (GP). Here they follow by projections onto either a piecewise constant (GP0) or a piecewise linear (GP1) space. Our framework thus provides essentially three different schemes with significantly different behavior. The split scheme using twice GP1 is unstable and shares the same discrete dispersion relation and similar second-order convergence rates as the conventional P1-P1 FE scheme that approximates both velocity and height variables by piecewise linear spaces. The split scheme that applies both GP1 and GP0 is stable and shares the dispersion relation of the conventional P1-P0 FE scheme that approximates the velocity by a piecewise linear and the height by a piecewise constant space with corresponding second- and first-order convergence rates. Exhibiting for both velocity and height fields second-order convergence rates, we might consider the split GP1-GP0 scheme though as stable versions of the conventional P1-P1 FE scheme. For the split scheme applying twice GP0, we are not aware of a corresponding conventional formulation to compare with. Though exhibiting larger

  18. LHCb: Measurement of $\\Delta m_s$ in the decay $B_s \\to D_s(3)\\pi$ at LHCb

    CERN Multimedia

    Wandernoth, S

    2011-01-01

    An analysis of the $B_s$-$\\overline{B}_s$ mixing frequency $\\Delta m_s$ was performed on a dataset of ~35 pb$^{-1}$ obtained from the LHCb physics run in 2010. After reconstruction about 1350 $B_s$ signal candidates are found in the decay $B_s \\to D_s (3)\\pi$ with an average proper time resolution of 36-44 fs. Opposite side flavour taggers with a tagging performance of $e_{eff} = 3.8 \\pm 2.1$ % were used. The observed mixing frequency is $\\Delta m_s = 17.63 \\pm 0.11(stat.) \\pm 0.04 (syst.) ps^{-1}$

  19. Pharmaceutical counselling about different types of tablet-splitting methods based on the results of weighing tests and mechanical development of splitting devices.

    Science.gov (United States)

    Somogyi, O; Meskó, A; Csorba, L; Szabó, P; Zelkó, R

    2017-08-30

    The division of tablets and adequate methods of splitting them are a complex problem in all sectors of health care. Although tablet-splitting is often required, this procedure can be difficult for patients. Four tablets were investigated with different external features (shape, score-line, film-coat and size). The influencing effect of these features and the splitting methods was investigated according to the precision and "weight loss" of splitting techniques. All four types of tablets were halved by four methods: by hand, with a kitchen knife, with an original manufactured splitting device and with a modified tablet splitter based on a self-developed mechanical model. The mechanical parameters (harness and friability) of the products were measured during the study. The "weight loss" and precision of splitting methods were determined and compared by statistical analysis. On the basis of the results, the external features (geometry), the mechanical parameters of tablets and the mechanical structure of splitting devices can influence the "weight loss" and precision of tablet-splitting. Accordingly, a new decision-making scheme was developed for the selection of splitting methods. In addition, the skills of patients and the specialties of therapy should be considered so that pharmaceutical counselling can be more effective regarding tablet-splitting. Copyright © 2017 Elsevier B.V. All rights reserved.

  20. Investigation of the Effects of Split Sleep Schedules on Commercial Vehicle Driver Safety and Health

    Science.gov (United States)

    2012-12-01

    The objective of this study was to evaluate the consequences for safety and health of split sleep versus consolidated sleep by comparing the effects of consolidated nighttime sleep, split sleep, and consolidated daytime sleep on total sleep time, per...

  1. A study on crustal shear wave splitting in the western part of the Banda arc-continent collision

    Energy Technology Data Exchange (ETDEWEB)

    Syuhada, E-mail: hadda9@gmail.com [Graduate Research on Earthquake and Active Tectonics-ITB, Jl. Ganesha 10, Bandung 40132 (Indonesia); Research Centre for Physics - Indonesian Institute of Sciences (LIPI), Puspiptek Serpong 15314,Indonesia (Indonesia); Hananto, Nugroho D. [Research Centre for Geotechnology -LIPI, Jl. Sangkuriang (Kompleks LIPI) Bandung 40135 (Indonesia); Puspito, Nanang T.; Yudistira, Tedi [Faculty of Mining and Petroleum Engineering ITB, Jalan Ganesha 10, Bandung 40132 (Indonesia); Anggono, Titi [Research Centre for Physics - Indonesian Institute of Sciences (LIPI), Puspiptek Serpong 15314,Indonesia (Indonesia)

    2016-03-11

    We analyzed shear wave splitting parameters from local shallow (< 30 km) earthquakes recorded at six seismic stations in the western part of the Banda arc-continent collision. We determined fast polarization and delay time for 195 event-stations pairs calculated from good signal-to-noise ratio waveforms. We observed that there is evidence for shear wave splitting at all stations with dominant fast polarization directions oriented about NE-SW, which are parallel to the collision direction of the Australian plate. However, minor fast polarization directions are oriented around NW-SE being perpendicular to the strike of Timor through. Furthermore, the changes in fast azimuths with the earthquake-station back azimuth suggest that the crustal anisotropy in the study area is not uniform. Splitting delay times are within the range of 0.05 s to 0.8 s, with a mean value of 0.29±0.18 s. Major seismic stations exhibit a weak tendency increasing of delay times with increasing hypocentral distance suggesting the main anisotropy contribution of the shallow crust. In addition, these variations in fast azimuths and delay times indicate that the crustal anisotropy in this region might not only be caused by extensive dilatancy anisotropy (EDA), but also by heterogeneity shallow structure such as the presence of foliations in the rock fabric and the fracture zones associated with active faults.

  2. A study on crustal shear wave splitting in the western part of the Banda arc-continent collision

    International Nuclear Information System (INIS)

    Syuhada; Hananto, Nugroho D.; Puspito, Nanang T.; Yudistira, Tedi; Anggono, Titi

    2016-01-01

    We analyzed shear wave splitting parameters from local shallow (< 30 km) earthquakes recorded at six seismic stations in the western part of the Banda arc-continent collision. We determined fast polarization and delay time for 195 event-stations pairs calculated from good signal-to-noise ratio waveforms. We observed that there is evidence for shear wave splitting at all stations with dominant fast polarization directions oriented about NE-SW, which are parallel to the collision direction of the Australian plate. However, minor fast polarization directions are oriented around NW-SE being perpendicular to the strike of Timor through. Furthermore, the changes in fast azimuths with the earthquake-station back azimuth suggest that the crustal anisotropy in the study area is not uniform. Splitting delay times are within the range of 0.05 s to 0.8 s, with a mean value of 0.29±0.18 s. Major seismic stations exhibit a weak tendency increasing of delay times with increasing hypocentral distance suggesting the main anisotropy contribution of the shallow crust. In addition, these variations in fast azimuths and delay times indicate that the crustal anisotropy in this region might not only be caused by extensive dilatancy anisotropy (EDA), but also by heterogeneity shallow structure such as the presence of foliations in the rock fabric and the fracture zones associated with active faults.

  3. Spin-valley splitting of electron beam in graphene

    Directory of Open Access Journals (Sweden)

    Yu Song

    2016-11-01

    Full Text Available We study spatial separation of the four degenerate spin-valley components of an electron beam in a EuO-induced and top-gated ferromagnetic/pristine/strained graphene structure. We show that, in a full resonant tunneling regime for all beam components, the formation of standing waves can lead sudden phase jumps ∼−π and giant lateral Goos-Hänchen shifts as large as the transverse beam width, while the interplay of the spin and valley imaginary wave vectors in the modulated regions can lead differences of resonant angles for the four spin-valley flavors, manifesting a spin-valley beam splitting effect. The splitting effect is found to be controllable by the gating and strain.

  4. Chargino pair production at linear collider and split supersymmetry

    International Nuclear Information System (INIS)

    Zhu Shouhua

    2004-01-01

    Recently Arkani-Hamed and Dimopoulos proposed a supersymmetric model [hep-th/0405159], dubbed 'Split supersymmetry' in [hep-ph/0406088], which can remove most of the unpleasant shortcomings of TeV Supersymmetry. In this model all scalars except one finely tuned Higgs boson are ultra heavy while the neutralino and chargino might remain light in order to achieve gauge coupling unification and accord with the dark matter density. In this Letter, we investigated the impact of this new model on chargino pair production at next generation linear colliders. Our numerical results show that this process can be used to probe sneutrino mass up to 10 TeV. Therefore, precise measurements of chargino pair production at the linear colliders could distinguish split supersymmetry from TeV supersymmetry

  5. Using Protection Layers for a 2-Photon Water Splitting Device

    DEFF Research Database (Denmark)

    Seger, Brian; Mei, Bastian Timo; Frydendal, Rasmus

    2015-01-01

    The 2-photon tandem device for photocatalytic water splitting has been theoretically shown to provide a higher efficiency than a single photon device(1). This increased efficiency can be achieved by having one material optimized to absorb high energy photons (large bandgap) and another material...... optimized to absorb low energy photons (small bandgap). To a large degree this approach has been hindered by corrosion issues. In this talk I will first discuss how our computational screening of 2,400 materials showed that very few materials can efficiently absorb light without corroding in water splitting...... conditions.(2) I will follow this up by discussing how protection layers bypass the corrosion issue by creating a buffer layer.(3) Finally I will show how we integrated a photocatalyst/protection layer/(co-catalyst) scheme to produce highly efficient H2 evolution photocathodes and O2 evolution photoanodes.(3...

  6. Photoelectrochemical water splitting standards, experimental methods, and protocols

    CERN Document Server

    Chen, Zhebo; Miller, Eric

    2014-01-01

    This book outlines many of the techniques involved in materials development and characterization for photoelectrochemical (PEC) - for example, proper metrics for describing material performance, how to assemble testing cells and prepare materials for assessment of their properties, and how to perform the experimental measurements needed to achieve reliable results towards better scientific understanding. For each technique, proper procedure, benefits, limitations, and data interpretation are discussed. Consolidating this information in a short, accessible, and easy to read reference guide will allow researchers to more rapidly immerse themselves into PEC research and also better compare their results against those of other researchers to better advance materials development. This book serves as a "how-to" guide for researchers engaged in or interested in engaging in the field of photoelectrochemical (PEC) water splitting. PEC water splitting is a rapidly growing field of research in which the goal is to deve...

  7. Photochemical water splitting mediated by a C1 shuttle

    KAUST Repository

    Alderman, N. P.

    2016-10-31

    The possibility of performing photochemical water splitting in a two-stage system, separately releasing the H and O components, has been probed with two separate catalysts and in combination with a formaldehyde/formate shuttling redox couple. In the first stage, formaldehyde releases hydrogen vigorously in the presence of an Na[Fe(CN)]·10HO catalyst, selectively affording the formate anion. In the second stage, the formate anion is hydro-genated back to formaldehyde by water and in the presence of a BiWO photocatalyst whilst releasing oxygen. Both stages operate at room temperature and under visible light irradiation. The two separate photocatalysts are compatible since water splitting can also be obtained in one-pot experiments with simultaneous H/O evolution.

  8. Toward visible light response: Overall water splitting using heterogeneous photocatalysts

    KAUST Repository

    Takanabe, Kazuhiro

    2011-01-01

    Extensive energy conversion of solar energy can only be achieved by large-scale collection of solar flux. The technology that satisfies this requirement must be as simple as possible to reduce capital cost. Overall water splitting by powder-form photocatalysts directly produces a mixture of H 2 and O2 (chemical energy) in a single reactor, which does not require any complicated parabolic mirrors and electronic devices. Because of its simplicity and low capital cost, it has tremendous potential to become the major technology of solar energy conversion. Development of highly efficient photocatalysts is desired. This review addresses why visible light responsive photocatalysts are essential to be developed. The state of the art for the photocatalysts for overall water splitting is briefly described. Moreover, various fundamental aspects for developing efficient photocatalysts, such as particle size of photocatalysts, cocatalysts, and reaction kinetics are discussed. Copyright © 2011 De Gruyter.

  9. Photoelectrochemical water splitting in separate oxygen and hydrogen cells

    Science.gov (United States)

    Landman, Avigail; Dotan, Hen; Shter, Gennady E.; Wullenkord, Michael; Houaijia, Anis; Maljusch, Artjom; Grader, Gideon S.; Rothschild, Avner

    2017-06-01

    Solar water splitting provides a promising path for sustainable hydrogen production and solar energy storage. One of the greatest challenges towards large-scale utilization of this technology is reducing the hydrogen production cost. The conventional electrolyser architecture, where hydrogen and oxygen are co-produced in the same cell, gives rise to critical challenges in photoelectrochemical water splitting cells that directly convert solar energy and water to hydrogen. Here we overcome these challenges by separating the hydrogen and oxygen cells. The ion exchange in our cells is mediated by auxiliary electrodes, and the cells are connected to each other only by metal wires, enabling centralized hydrogen production. We demonstrate hydrogen generation in separate cells with solar-to-hydrogen conversion efficiency of 7.5%, which can readily surpass 10% using standard commercial components. A basic cost comparison shows that our approach is competitive with conventional photoelectrochemical systems, enabling safe and potentially affordable solar hydrogen production.

  10. Protein subcellular localization assays using split fluorescent proteins

    Science.gov (United States)

    Waldo, Geoffrey S [Santa Fe, NM; Cabantous, Stephanie [Los Alamos, NM

    2009-09-08

    The invention provides protein subcellular localization assays using split fluorescent protein systems. The assays are conducted in living cells, do not require fixation and washing steps inherent in existing immunostaining and related techniques, and permit rapid, non-invasive, direct visualization of protein localization in living cells. The split fluorescent protein systems used in the practice of the invention generally comprise two or more self-complementing fragments of a fluorescent protein, such as GFP, wherein one or more of the fragments correspond to one or more beta-strand microdomains and are used to "tag" proteins of interest, and a complementary "assay" fragment of the fluorescent protein. Either or both of the fragments may be functionalized with a subcellular targeting sequence enabling it to be expressed in or directed to a particular subcellular compartment (i.e., the nucleus).

  11. Image segmentation by iterative parallel region growing and splitting

    Science.gov (United States)

    Tilton, James C.

    1989-01-01

    The spatially constrained clustering (SCC) iterative parallel region-growing technique is applied to image analysis. The SCC algorithm is implemented on the massively parallel processor at NASA Goddard. Most previous region-growing approaches have the drawback that the segmentation produced depends on the order in which portions of the image are processed. The ideal solution to this problem (merging only the single most similar pair of spatially adjacent regions in the image in each iteration) becomes impractical except for very small images, even on a massively parallel computer. The SCC algorithm overcomes these problems by performing, in parallel, the best merge within each of a set of local, possibly overlapping, subimages. A region-splitting stage is also incorporated into the algorithm, but experiments show that region splitting generally does not improve segmentation results. The SCC algorithm has been tested on various imagery data, and test results for a Landsat TM image are summarized.

  12. Isospin Mass Splittings and the $\\ms$ Corrections in the Semibosonized SU(3)-NJL-Model

    OpenAIRE

    Blotz, Andree; Goeke, K.; Praszalowicz, M.

    1994-01-01

    The mass splittings of hyperons including the isospin splittings are calculated with $O(\\ms^2)$ and $O(\\ms \\dm)$ accuracy respectively within the semibosonized SU(3)-NJL model. The pattern of the isospin splittings is not spoiled by the terms of the order $O(\\ms \\dm)$, and both splittings between the different isospin multiplets and within the same multiplet are well reproduced for acceptable values of $\\ms$ and $\\dm$.

  13. Investigation of the Physical Properties of Sprayed Nanocrystalline In2S3 Films

    Science.gov (United States)

    Bouguila, N.; Kraini, M.; Najeh, I.; Halidou, I.; Lacaze, E.; Bouchriha, H.; Bouzouita, H.; Alaya, S.

    2015-11-01

    In2S3 films have been grown on preheated glass substrate by spray pyrolysis. Indium chloride and thiourea in the molar ratio S:In = 2 were used as reagents. Substrate temperature was fixed at 613 K. These films adhered well to the substrate and were approximately 2 μm thick. Structural, morphological, optical, and electrical properties of the as-grown In2S3 films were studied by use of x-ray diffraction (XRD) analysis, energy-dispersive spectroscopy, atomic force microscopy (AFM), optical absorption spectroscopy, and impedance spectroscopy. XRD revealed well crystallized films oriented in the (400) direction corresponding to the cubic β-In2S3 phase. The surface of the films was smooth; average roughness was 5 nm. The AFM image revealed that the films were nanopolycrystalline and contained grains in the range 20-30 nm. Optical transmission in the visible and near-infrared regions was 80%. The direct band-gap energy was 2.62 eV. The electrical data were analyzed on the basis of the impedance Cole-Cole plots in the frequency range 0.1 Hz to 100 kHz at room temperature. Constant-phase elements were used in equivalent electrical circuits for fitting of experimental impedance data. The experimental results were fitted to the equivalent electrical circuit by use of Z-view software. The conductivity of grains and grain boundaries was estimated. The gas-sensing properties of the sample were investigated on the basis of the change in conductance as a result of adsorption and desorption of atmospheric oxygen.

  14. Passive permeability of salicylic acid in renal proximal S2 and S3 tubules

    International Nuclear Information System (INIS)

    Chatton, J.Y.; Roch-Ramel, F.

    1991-01-01

    The role of nonionic diffusion in the transport of salicylic acid across rabbit proximal S2 and S3 segments was investigated using the in vitro isolated perfused tubule technique. The [ 14 C] salicylic acid apparent reabsorptive permeability (P'I-b, 10(-5) cm/s) was measured at 19 degrees C with luminal solutions kept at different pH and bath maintained at pH 7.4. In S2 tubules, P'I-b was 25.0 +/- 3.5 when luminal pH was 6.0; P'I-b decreased to 8.1 +/- 1.4 and to 4.4 +/- 1.2 at a luminal pH of 6.5 and 7.0, respectively. In S3 tubules, P'I-b was 17.6 +/- 2.4, 5.3 +/- 1.1 and 3.4 +/- 1.1 at a luminal pH of 6.0, 6.5 and 7.0, respectively. There was a close correlation between P'I-b and the calculated proportion of nonionized salicylic acid present at each pH, indicating that only the nonionized molecule could diffuse in our conditions. We calculated the apparent permeability of nonionic salicylic acid and found 0.248 +/- 0.032 cm/s for S2 and 0.176 +/- 0.022 cm/s for S3 tubules. These calculated permeabilities were independent of pH

  15. Transfer Pricing Profit Split Methods : A Practical Solution?

    OpenAIRE

    Quttineh, Yousef

    2009-01-01

    The purpose of this master’s thesis is to explain and analyze whether today’s existing regulations provide sufficient guidance on how to apply the Profit Split Method (PSM) in practice. Since the enterprises’ profits arising from intra-group transactions increases, the tax base for any government also becomes larger and more important. This issue will likely become even more problematic as the globalization branches out and the majority of the global trade is undertaken between associated ent...

  16. Left-right splitting for electromagnetic scattering in 3D

    CERN Document Server

    Spivack, M; Sillence, C; 10.1049/ip-smt:20040945

    2004-01-01

    The left-right splitting method and its application to electromagnetic scattering by large 3D scatterers are described. Exact numerical solutions to the governing integral equations can be prohibitively expensive for large scatterers. Under the assumption that energy is predominantly forward-scattered, the solution is expressed as a series of terms, each of which is rapidly and efficiently evaluated. In many cases only one or two terms are needed, and the formulation provides additional physical insight.

  17. Chitosan Nanoparticle Encapsulated Hemagglutinin-Split Influenza Virus Mucosal Vaccine

    OpenAIRE

    Sawaengsak, Chompoonuch; Mori, Yasuko; Yamanishi, Koichi; Mitrevej, Ampol; Sinchaipanid, Nuttanan

    2013-01-01

    Subunit/split influenza vaccines are less reactogenic compared with the whole virus vaccines. However, their immunogenicity is relatively low and thus required proper adjuvant and/or delivery vehicle for immunogenicity enhancement. Influenza vaccines administered intramuscularly induce minimum, if any, mucosal immunity at the respiratory mucosa which is the prime site of the infection. In this study, chitosan (CS) nanoparticles were prepared by ionic cross-linking of the CS with sodium tripol...

  18. Point splitting regularization of classical string field theory

    International Nuclear Information System (INIS)

    Strominger, A.

    1987-01-01

    We regulate Witten's star algebra using point splitting and conformal field theory techniques. Certain products of nonassociative operators and states are defined. This involves a refinement of star that exists in cases where Witten's star is ill-defined. A simple derivation of a recently discovered associativity anomaly is given. It is shown that there is no anomaly obstructing the equivalence of Witten's string theory action and the cubic action for string fields in the open string Fock space. (orig.)

  19. Shear-wave splitting measurements – Problems and solutions

    Czech Academy of Sciences Publication Activity Database

    Vecsey, Luděk; Plomerová, Jaroslava; Babuška, Vladislav

    2008-01-01

    Roč. 462, č. 1-4 (2008), s. 178-196 ISSN 0040-1951 R&D Projects: GA AV ČR(CZ) KJB300120605; GA AV ČR IAA3012405; GA AV ČR IAA300120709 Institutional research plan: CEZ:AV0Z30120515 Keywords : seismic anisotropy * shear-wave splitting * comparison of cross- correlation * eigenvalue * transverse minimization methods Subject RIV: DC - Siesmology, Volcanology, Earth Structure Impact factor: 1.677, year: 2008

  20. Hanford tank wastes; salt splitting: FY92 activities

    International Nuclear Information System (INIS)

    Hickman, R.G.

    1992-09-01

    For the first time, sodium nitrate was split into the nitric acid and sodium hydroxide from which it originated. Current-voltage characteristics were determined and found to be in the range normally judged to be economically feasible. Six different membranes were exposed to 1M NaOH or 1M HN0 3 for 100 days without apparent deterioration. It is concluded that this technology holds significant promise for the processing of Hanford Tank Wastes

  1. Split-based computation of majority-rule supertrees.

    Science.gov (United States)

    Kupczok, Anne

    2011-07-13

    Supertree methods combine overlapping input trees into a larger supertree. Here, I consider split-based supertree methods that first extract the split information of the input trees and subsequently combine this split information into a phylogeny. Well known split-based supertree methods are matrix representation with parsimony and matrix representation with compatibility. Combining input trees on the same taxon set, as in the consensus setting, is a well-studied task and it is thus desirable to generalize consensus methods to supertree methods. Here, three variants of majority-rule (MR) supertrees that generalize majority-rule consensus trees are investigated. I provide simple formulas for computing the respective score for bifurcating input- and supertrees. These score computations, together with a heuristic tree search minmizing the scores, were implemented in the python program PluMiST (Plus- and Minus SuperTrees) available from http://www.cibiv.at/software/plumist. The different MR methods were tested by simulation and on real data sets. The search heuristic was successful in combining compatible input trees. When combining incompatible input trees, especially one variant, MR(-) supertrees, performed well. The presented framework allows for an efficient score computation of three majority-rule supertree variants and input trees. I combined the score computation with a heuristic search over the supertree space. The implementation was tested by simulation and on real data sets and showed promising results. Especially the MR(-) variant seems to be a reasonable score for supertree reconstruction. Generalizing these computations to multifurcating trees is an open problem, which may be tackled using this framework.

  2. Split-Plot Designs with Mirror Image Pairs as Subplots

    DEFF Research Database (Denmark)

    Tyssedal, John; Kulahci, Murat; Bisgaard, Soren

    2011-01-01

    In this article we investigate two-level split-plot designs where the sub-plots consist of only two mirror image trials. Assuming third and higher order interactions negligible, we show that these designs divide the estimated effects into two orthogonal sub-spaces, separating sub-plot main effects...... appealing with effects of major interest free from full aliasing assuming that 3rd and higher order interactions are negligible....

  3. Some Fixed Points Results of Quadratic Functions in Split Quaternions

    Directory of Open Access Journals (Sweden)

    Young Chel Kwun

    2016-01-01

    Full Text Available We attempt to find fixed points of a general quadratic polynomial in the algebra of split quaternion. In some cases, we characterize fixed points in terms of the coefficients of these polynomials and also give the cardinality of these points. As a consequence, we give some simple examples to strengthen the infinitude of these points in these cases. We also find the roots of quadratic polynomials as simple consequences.

  4. Fluorescence of molecules placed near a spherical particle: Rabi splitting

    Directory of Open Access Journals (Sweden)

    M.M. Dvoynenko

    2017-12-01

    Full Text Available Theoretical study of spontaneously emitted spectra of point-like source placed near spherical Ag particle was performed. It was shown that near-field electromagnetic interaction between a point-like emitter and spherical Ag particle leads to strong coupling between them at very small emitter-metal surface distances. It was shown that values of Rabi splitting are quantitatively close to that of emitter-flat substrate interaction.

  5. Ultrafast reduction of exchange splitting in ferromagnetic nickel

    International Nuclear Information System (INIS)

    Zhang, G P; Bai, Y H; George, Thomas F

    2016-01-01

    A decade ago Rhie et al (2003 Phys. Rev. Lett . 90 247201) reported that when ferromagnetic nickel is subject to an intense ultrashort laser pulse, its exchange splitting is reduced quickly. But to simulate such reduction remains a big challenge. The popular rigid band approximation (RBA), where both the band structure and the exchange splitting are held fixed before and after laser excitation, is unsuitable for this purpose, while the time-dependent density functional theory could be time-consuming. To overcome these difficulties, we propose a time-dependent Liouville and density functional theory (TDLDFT) that integrates the time-dependent Liouville equation into the density functional theory. As a result, the excited charge density is reiterated back into the Kohn–Sham equation, and the band structure is allowed to change dynamically. Even with the ground-state density functional, a larger demagnetization than RBA is found; after we expand Ortenzi’s spin scaling method into an excited-state (laser) density functional, we find that the exchange splitting is indeed strongly reduced, as seen in the experiment. Both the majority and minority bands are shifted toward the Fermi level, but the majority shifts a lot more. The ultrafast reduction in exchange splitting occurs concomitantly with demagnetization. While our current theory is still unable to yield the same percentage loss in the spin moment as observed in the experiment, it predicts a correct trend that agrees with the experiments. With a better functional, we believe that our results can be further improved. (paper)

  6. Interpretation and inverse analysis of the wedge splitting test

    DEFF Research Database (Denmark)

    Østergaard, Lennart; Stang, Henrik

    2002-01-01

    to the wedge splitting test and that it is well suited for the interpretation of test results in terms of s(w). A fine agreement between the hinge and FEM-models has been found. It has also been found that the test and the hinge model form a solid basis for inverse analysis. The paper also discusses possible...... three dimensional problems in the experiment as well as the influence of specimen size....

  7. Split-Stirling-cycle displacer linear-electric drive

    Science.gov (United States)

    Ackermann, R. A.; Bhate, S. K.; Byrne, D. V.

    1983-01-01

    The retrofit of a 1/4-W split-Stirling cooler with a linear driven on the displacer was achieved and its performance characterized. The objective of this work was to demonstrate that a small linear motor could be designed to meet the existing envelope specifications of the cooler and that an electric linear drive on the displacer could improve the cooler's reliability and performance. The paper describes the characteristics of this motor and presents cooler test results.

  8. S3 guidelines for diagnostics and treatment of peripheral arterial occlusive disease

    International Nuclear Information System (INIS)

    Huppert, P.; Tacke, J.; Lawall, H.

    2010-01-01

    This report summarizes the most important aspects of the new German S3 guidelines for the diagnostics and treatment of peripheral arterial occlusive disease (PAOD) from March 2009. The guidelines include definitions and epidemiology of peripheral arterial occlusive disease, diagnostic methods including clinical and technical procedures as well as imaging methods, treatment by non-invasive, interventional and surgical methods and patient care during follow-up. In key messages recommendations are given which are graded corresponding to the scientific evidence concluded from the literature. (orig.) [de

  9. S3C: EBT Steady-State Shooting code description and user's guide

    International Nuclear Information System (INIS)

    Downum, W.B.

    1983-09-01

    The Oak Ridge National Laboratory (ORNL) one-dimensional (1-D) Steady-State Shooting code (S3C) for ELMO Bumpy Torus (EBT) plasmas is described. Benchmark calculations finding the steady-state density and electron and ion temperature profiles for a known neutral density profile and known external energy sources are carried out. Good agreement is obtained with results from the ORNL Radially Resolved Time Dependent 1-D Transport code for an EBT-Q type reactor. The program logic is described, along with the physics models in each code block and the variable names used. Sample input and output files are listed, along with the main code

  10. Application of glucoamylase produced by aspergillus niger mutant a. S. 3. 4309 in alcohol industry

    Energy Technology Data Exchange (ETDEWEB)

    1981-01-01

    A glucoamylase (I) A. niger mutant was used for the industrial-scale production of EtOH. Thus, enough A. niger A.S. 3.4309 equiv to 63-79 units I/g substrate was added to a medium (pH 4.5) containing 6-10% corn powder, 2% corn steep liquor, and 2% soybean powder. The mixture was first saccharified at 55-60 degrees and then fermented at 30 degrees for 72 hours. The production of EtOH was approximately 13 tons in a 5000 L fermentor system.

  11. A split accumulation gate architecture for silicon MOS quantum dots

    Science.gov (United States)

    Rochette, Sophie; Rudolph, Martin; Roy, Anne-Marie; Curry, Matthew; Ten Eyck, Gregory; Dominguez, Jason; Manginell, Ronald; Pluym, Tammy; King Gamble, John; Lilly, Michael; Bureau-Oxton, Chloé; Carroll, Malcolm S.; Pioro-Ladrière, Michel

    We investigate tunnel barrier modulation without barrier electrodes in a split accumulation gate architecture for silicon metal-oxide-semiconductor quantum dots (QD). The layout consists of two independent accumulation gates, one gate forming a reservoir and the other the QD. The devices are fabricated with a foundry-compatible, etched, poly-silicon gate stack. We demonstrate 4 orders of magnitude of tunnel-rate control between the QD and the reservoir by modulating the reservoir gate voltage. Last electron charging energies of app. 10 meV and tuning of the ST splitting in the range 100-200 ueV are observed in two different split gate layouts and labs. This work was performed, in part, at the Center for Integrated Nanotechnologies, an Office of Science User Facility operated for the U.S. Department of Energy (DOE) Office of Science. Sandia National Laboratories is a multi-program laboratory operated by Sandia Corporation, a Lockheed-Martin Company, for the U. S. Department of Energy under Contract No. DE-AC04-94AL85000.

  12. Photoelectrochemical devices for solar water splitting - materials and challenges.

    Science.gov (United States)

    Jiang, Chaoran; Moniz, Savio J A; Wang, Aiqin; Zhang, Tao; Tang, Junwang

    2017-07-31

    It is widely accepted within the community that to achieve a sustainable society with an energy mix primarily based on solar energy we need an efficient strategy to convert and store sunlight into chemical fuels. A photoelectrochemical (PEC) device would therefore play a key role in offering the possibility of carbon-neutral solar fuel production through artificial photosynthesis. The past five years have seen a surge in the development of promising semiconductor materials. In addition, low-cost earth-abundant co-catalysts are ubiquitous in their employment in water splitting cells due to the sluggish kinetics of the oxygen evolution reaction (OER). This review commences with a fundamental understanding of semiconductor properties and charge transfer processes in a PEC device. We then describe various configurations of PEC devices, including single light-absorber cells and multi light-absorber devices (PEC, PV-PEC and PV/electrolyser tandem cell). Recent progress on both photoelectrode materials (light absorbers) and electrocatalysts is summarized, and important factors which dominate photoelectrode performance, including light absorption, charge separation and transport, surface chemical reaction rate and the stability of the photoanode, are discussed. Controlling semiconductor properties is the primary concern in developing materials for solar water splitting. Accordingly, strategies to address the challenges for materials development in this area, such as the adoption of smart architectures, innovative device configuration design, co-catalyst loading, and surface protection layer deposition, are outlined throughout the text, to deliver a highly efficient and stable PEC device for water splitting.

  13. SKS splitting observed at Romanian broad-band seismic network

    Science.gov (United States)

    Ivan, Marian; Popa, Mihaela; Ghica, Daniela

    2008-12-01

    Shear-wave splitting results are presented for the broad-band stations of the Romanian seismic network. For stations BUC1 and CRAR (located in Moesian Platform), IAS (in East-European Platform), TIRR and CVD (in Central Dobrudja-Black Sea microplate), TIM and DRGR (in Dacia-Tisza plate, including Apuseni Mts.), BURAR, BZS and GZR (in, or very close to the Carpathian Arc), the fast directions ( φ) are around 135°. The mean delay values ( δt) of the slow wave are slightly greater for the stations placed in platform areas ( δt ~ 1.5 s) than for the stations situated in the (proximity) of Carpathians ( δt ~ 1.2 s). For the MLR station located in the South-Western part of Vrancea area, at the Carpathian Bend, the fast direction is 48°, similar to VOIR station (located in Southern Carpathians, 70 km West of MLR). At VRI and PLOR, located in the North-Eastern part of Vrancea, the fast axis is oriented approximately on North-South direction, with a possible dependence of the splitting parameters with back azimuth. At least for some stations, the splitting results are not consistent with vertical coherent lithospheric anisotropy.

  14. Photocatalytic and Photoelectrochemical Water Splitting by Inorganic Materials

    KAUST Repository

    Deng, Xiaohui

    2012-12-01

    Hydrogen has been identified as a potential energy carrier due to its high energy capacity and environmental harmlessness. Compared with hydrogen production from hydrocarbons such as methane and naphtha in a conventional hydrogen energy system, photocatalytic hydrogen evolution from water splitting offers a more economic approach since it utilizes the abundant solar irradiation as energy source and water as initial reactant. Powder photocatalyst, which generates electrons and holes under illumination, is the origin where the overall reaction happens. High solar energy conversion efficiency especially from visible range is commonly the target. Besides, cocatalyst for hydrogen and oxygen evolution is also playing an essential role in facilitating the charge separation and enhancing the kinetics. In this thesis, the objective is to achieve high energy conversion efficiency towards water splitting from diverse aspects. The third chapter focuses on a controllable method to fabricate metal pattern, which is candidate for hydrogen evolution cocatalyst while chapter 4 is on the combination of strontium titanium oxide (SrTiO3) with graphene oxide (GO) for a better photocatalytic performance. In the last chapter, photoelectrochemical water splitting by Ta3N5 photoanode and FeOOH as a novel oxygen evolution cocatalyst has been investigated.

  15. Fundamental metallurgical aspects of axial splitting in zircaloy cladding

    International Nuclear Information System (INIS)

    Chung, H. M.

    2000-01-01

    Fundamental metallurgical aspects of axial splitting in irradiated Zircaloy cladding have been investigated by microstructural characterization and analytical modeling, with emphasis on application of the results to understand high-burnup fuel failure under RIA situations. Optical microscopy, SEM, and TEM were conducted on BWR and PWR fuel cladding tubes that were irradiated to fluence levels of 3.3 x 10 21 n cm -2 to 5.9 x 10 21 n cm -2 (E > 1 MeV) and tested in hot cell at 292--325 C in Ar. The morphology, distribution, and habit planes of macroscopic and microscopic hydrides in as-irradiated and posttest cladding were determined by stereo-TEM. The type and magnitude of the residual stress produced in association with oxide-layer growth and dense hydride precipitation, and several synergistic factors that strongly influence axial-splitting behavior were analyzed. The results of the microstructural characterization and stress analyses were then correlated with axial-splitting behavior of high-burnup PWR cladding reported for simulated-RIA conditions. The effects of key test procedures and their implications for the interpretation of RIA test results are discussed

  16. A Beta-splitting model for evolutionary trees.

    Science.gov (United States)

    Sainudiin, Raazesh; Véber, Amandine

    2016-05-01

    In this article, we construct a generalization of the Blum-François Beta-splitting model for evolutionary trees, which was itself inspired by Aldous' Beta-splitting model on cladograms. The novelty of our approach allows for asymmetric shares of diversification rates (or diversification 'potential') between two sister species in an evolutionarily interpretable manner, as well as the addition of extinction to the model in a natural way. We describe the incremental evolutionary construction of a tree with n leaves by splitting or freezing extant lineages through the generating, organizing and deleting processes. We then give the probability of any (binary rooted) tree under this model with no extinction, at several resolutions: ranked planar trees giving asymmetric roles to the first and second offspring species of a given species and keeping track of the order of the speciation events occurring during the creation of the tree, unranked planar trees, ranked non-planar trees and finally (unranked non-planar) trees. We also describe a continuous-time equivalent of the generating, organizing and deleting processes where tree topology and branch lengths are jointly modelled and provide code in SageMath/Python for these algorithms.

  17. Nanoscale strontium titanate photocatalysts for overall water splitting.

    Science.gov (United States)

    Townsend, Troy K; Browning, Nigel D; Osterloh, Frank E

    2012-08-28

    SrTiO(3) (STO) is a large band gap (3.2 eV) semiconductor that catalyzes the overall water splitting reaction under UV light irradiation in the presence of a NiO cocatalyst. As we show here, the reactivity persists in nanoscale particles of the material, although the process is less effective at the nanoscale. To reach these conclusions, Bulk STO, 30 ± 5 nm STO, and 6.5 ± 1 nm STO were synthesized by three different methods, their crystal structures verified with XRD and their morphology observed with HRTEM before and after NiO deposition. In connection with NiO, all samples split water into stoichiometric mixtures of H(2) and O(2), but the activity is decreasing from 28 μmol H(2) g(-1) h(-1) (bulk STO), to 19.4 μmol H(2) g(-1) h(-1) (30 nm STO), and 3.0 μmol H(2) g(-1) h(-1) (6.5 nm STO). The reasons for this decrease are an increase of the water oxidation overpotential for the smaller particles and reduced light absorption due to a quantum size effect. Overall, these findings establish the first nanoscale titanate photocatalyst for overall water splitting.

  18. Investigation of the splitting of quark and gluon jets

    CERN Document Server

    Abreu, P; Adye, T; Adzic, P; Ajinenko, I; Alekseev, G D; Alemany, R; Allport, P P; Almehed, S; Amaldi, Ugo; Amato, S; Andersson, P; Andreazza, A; Antilogus, P; Apel, W D; Arnoud, Y; Åsman, B; Augustin, J E; Augustinus, A; Baillon, Paul; Bambade, P; Barão, F; Barbier, R; Bardin, Dimitri Yuri; Barker, G; Baroncelli, A; Bärring, O; Bates, M J; Battaglia, Marco; Baubillier, M; Becks, K H; Begalli, M; Beillière, P; Belokopytov, Yu A; Belous, K S; Benvenuti, Alberto C; Bérat, C; Berggren, M; Bertini, D; Bertrand, D; Besançon, M; Bianchi, F; Bigi, M; Bilenky, S M; Billoir, P; Bizouard, M A; Bloch, D; Bonesini, M; Bonivento, W; Boonekamp, M; Booth, P S L; Borgland, A W; Borisov, G; Bosio, C; Botner, O; Boudinov, E; Bouquet, B; Bourdarios, C; Bowcock, T J V; Bozovic, I; Bozzo, M; Branchini, P; Brand, K D; Brenke, T; Brenner, R A; Brown, R; Brückman, P; Brunet, J M; Bugge, L; Buran, T; Burgsmüller, T; Buschmann, P; Cabrera, S; Caccia, M; Calvi, M; Camacho-Rozas, A J; Camporesi, T; Canale, V; Canepa, M; Carena, F; Carroll, L; Caso, Carlo; Castillo-Gimenez, M V; Cattai, A; Cavallo, F R; Cerruti, C; Chabaud, V; Chapkin, M M; Charpentier, P; Chaussard, L; Checchia, P; Chelkov, G A; Chen, M; Chierici, R; Chliapnikov, P V; Chochula, P; Chorowicz, V; Chudoba, J; Collins, P; Colomer, M; Contri, R; Cortina, E; Cosme, G; Cossutti, F; Cowell, J H; Crawley, H B; Crennell, D J; Crosetti, G; Cuevas-Maestro, J; Czellar, S; D'Almagne, B; Damgaard, G; Dauncey, P D; Davenport, Martyn; Da Silva, W; Deghorain, A; Della Ricca, G; Delpierre, P A; Demaria, N; De Angelis, A; de Boer, Wim; De Brabandere, S; De Clercq, C; La Vaissière, C de; De Lotto, B; De Min, A; De Paula, L S; Dijkstra, H; Di Ciaccio, Lucia; Di Diodato, A; Djannati, A; Dolbeau, J; Doroba, K; Dracos, M; Drees, J; Drees, K A; Dris, M; Duperrin, A; Durand, J D; Edsall, D M; Ehret, R; Eigen, G; Ekelöf, T J C; Ekspong, Gösta; Ellert, M; Elsing, M; Engel, J P; Erzen, B; Espirito-Santo, M C; Falk, E; Fanourakis, G K; Fassouliotis, D; Fayot, J; Feindt, Michael; Fenyuk, A; Ferrari, P; Ferrer, A; Fichet, S; Firestone, A; Fischer, P A; Flagmeyer, U; Föth, H; Fokitis, E; Fontanelli, F; Formenti, F; Franek, B J; Frodesen, A G; Fulda-Quenzer, F; Fuster, J A; Galloni, A; Gamba, D; Gandelman, M; García, C; García, J; Gaspar, C; Gaspar, M; Gasparini, U; Gavillet, P; Gazis, E N; Gelé, D; Gerber, J P; Ghodbane, N; Glege, F; Gokieli, R; Golob, B; Gonçalves, P; González-Caballero, I; Gopal, Gian P; Gorn, L; Górski, M; Gracco, Valerio; Grahl, J; Graziani, E; Green, C; Grefrath, A; Gris, P; Grosdidier, G; Grzelak, K; Günther, M; Guy, J; Hahn, F; Hahn, S; Haider, S; Hajduk, Z; Hallgren, A; Hamacher, K; Harris, F J; Hedberg, V; Heising, S; Henriques, R P; Hernández, J J; Herquet, P; Herr, H; Hessing, T L; Heuser, J M; Higón, E; Holmgren, S O; Holt, P J; Holthuizen, D J; Hoorelbeke, S; Houlden, M A; Hrubec, Josef; Huet, K; Hultqvist, K; Jackson, J N; Jacobsson, R; Jalocha, P; Janik, R; Jarlskog, C; Jarlskog, G; Jarry, P; Jean-Marie, B; Johansson, E K; Jönsson, L B; Jönsson, P E; Joram, C; Juillot, P; Kapusta, F; Karafasoulis, K; Katsanevas, S; Katsoufis, E C; Keränen, R; Khokhlov, Yu A; Khomenko, B A; Khovanskii, N N; King, B J; Kjaer, N J; Klapp, O; Klein, H; Kluit, P M; Knoblauch, D; Kokkinias, P; Konoplyannikov, A K; Koratzinos, M; Korcyl, K; Kostyukhin, V; Kourkoumelis, C; Kuznetsov, O; Krammer, Manfred; Kreuter, C; Kronkvist, I J; Krumshtein, Z; Kubinec, P; Kucewicz, W; Kurvinen, K L; Lacasta, C; Lamsa, J; Lanceri, L; Lane, D W; Langefeld, P; Laugier, J P; Lauhakangas, R; Leder, Gerhard; Ledroit, F; Lefébure, V; Legan, C K; Leisos, A; Leitner, R; Lemonne, J; Lenzen, Georg; Lepeltier, V; Lesiak, T; Lethuillier, M; Libby, J; Liko, D; Lipniacka, A; Lippi, I; Lörstad, B; Loken, J G; Lopes, J H; López, J M; Loukas, D; Lutz, P; Lyons, L; MacNaughton, J N; Maehlum, G; Mahon, J R; Maio, A; Malek, A; Malmgren, T G M; Malychev, V; Mandl, F; Marco, J; Marco, R P; Maréchal, B; Margoni, M; Marin, J C; Mariotti, C; Markou, A; Martínez-Rivero, C; Martínez-Vidal, F; Martí i García, S; Masik, J; Matorras, F; Matteuzzi, C; Matthiae, Giorgio; Mazzucato, F; Mazzucato, M; McCubbin, M L; McKay, R; McNulty, R; McPherson, G; Medbo, J; Meroni, C; Meyer, W T; Myagkov, A; Michelotto, M; Migliore, E; Mirabito, L; Mitaroff, Winfried A; Mjörnmark, U; Moa, T; Møller, R; Mönig, K; Monge, M R; Moreau, X; Morettini, P; Müller, H; Münich, K; Mulders, M; Mundim, L M; Murray, W J; Muryn, B; Myatt, Gerald; Myklebust, T; Naraghi, F; Navarria, Francesco Luigi; Navas, S; Nawrocki, K; Negri, P; Némécek, S; Neufeld, N; Neumann, W; Neumeister, N; Nicolaidou, R; Nielsen, B S; Nieuwenhuizen, M; Nikolaenko, V; Nikolenko, M; Niss, P; Nomerotski, A; Normand, Ainsley; Nygren, A; Oberschulte-Beckmann, W; Obraztsov, V F

    1998-01-01

    The splitting processes in identified quark and gluon jets are investigated using longitudinal and transverse observables. The jets are selected from symmetric three-jet events measured in Z decays L with the {\\sc Delphi} detector in 1991-1994. Gluon jets are identified using heavy quark anti-tagging. Scaling violations in identified gluon jets are observed for the first time. The scale energy dependence of the gluon fragmentation function is found to be about two times larger than for the corresponding quark jets, consistent with the QCD expectation $C_A/C_F$. The primary splitting of gluons and quarks into subjets agrees with fragmentation models and, for specific regions of the jet resolution $y$, with NLLA calculations. The maximum of the ratio of the primary subjet splittings in quark and gluon jets is $2.77\\pm0.11\\pm0.10$. Due to non-perturbative effects, the data are below the expectation at small $y$. The transition from the perturbative to the non-perturbative domain appears at smaller $y$ for quark ...

  19. Noble metal-free hydrogen evolution catalysts for water splitting.

    Science.gov (United States)

    Zou, Xiaoxin; Zhang, Yu

    2015-08-07

    Sustainable hydrogen production is an essential prerequisite of a future hydrogen economy. Water electrolysis driven by renewable resource-derived electricity and direct solar-to-hydrogen conversion based on photochemical and photoelectrochemical water splitting are promising pathways for sustainable hydrogen production. All these techniques require, among many things, highly active noble metal-free hydrogen evolution catalysts to make the water splitting process more energy-efficient and economical. In this review, we highlight the recent research efforts toward the synthesis of noble metal-free electrocatalysts, especially at the nanoscale, and their catalytic properties for the hydrogen evolution reaction (HER). We review several important kinds of heterogeneous non-precious metal electrocatalysts, including metal sulfides, metal selenides, metal carbides, metal nitrides, metal phosphides, and heteroatom-doped nanocarbons. In the discussion, emphasis is given to the synthetic methods of these HER electrocatalysts, the strategies of performance improvement, and the structure/composition-catalytic activity relationship. We also summarize some important examples showing that non-Pt HER electrocatalysts could serve as efficient cocatalysts for promoting direct solar-to-hydrogen conversion in both photochemical and photoelectrochemical water splitting systems, when combined with suitable semiconductor photocatalysts.

  20. Sonochemical water splitting in the presence of powdered metal oxides.

    Science.gov (United States)

    Morosini, Vincent; Chave, Tony; Virot, Matthieu; Moisy, Philippe; Nikitenko, Sergey I

    2016-03-01

    Kinetics of hydrogen formation was explored as a new chemical dosimeter allowing probing the sonochemical activity of argon-saturated water in the presence of micro- and nano-sized metal oxide particles exhibiting catalytic properties (ThO2, ZrO2, and TiO2). It was shown that the conventional sonochemical dosimeter based on H2O2 formation is hardly applicable in such systems due to catalytic degradation of H2O2 at oxide surface. The study of H2 generation revealed that at low-frequency ultrasound (20 kHz) the sonochemical water splitting is greatly improved for all studied metal oxides. The highest efficiency is observed for relatively large micrometric particles of ThO2 which is assigned to ultrasonically-driven particle fragmentation accompanied by mechanochemical water molecule splitting. The nanosized metal oxides do not exhibit particle size reduction under ultrasonic treatment but nevertheless yield higher quantities of H2. The enhancement of sonochemical water splitting in this case is most probably resulting from better bubble nucleation in heterogeneous systems. At high-frequency ultrasound (362 kHz), the effect of metal oxide particles results in a combination of nucleation and ultrasound attenuation. In contrast to 20 kHz, micrometric particles slowdown the sonolysis of water at 362 kHz due to stronger attenuation of ultrasonic waves while smaller particles show a relatively weak and various directional effects. Copyright © 2015 Elsevier B.V. All rights reserved.

  1. The nature of photocatalytic "water splitting" on silicon nanowires.

    Science.gov (United States)

    Liu, Dong; Li, Leilei; Gao, Yang; Wang, Chengming; Jiang, Jun; Xiong, Yujie

    2015-03-02

    Silicon should be an ideal semiconductor material if it can be proven usable for photocatalytic water splitting, given its high natural abundance. Thus it is imperative to explore the possibility of water splitting by running photocatalysis on a silicon surface and to decode the mechanism behind it. It is reported that hydrogen gas can indeed be produced from Si nanowires when illuminated in water, but the reactions are not a real water-splitting process. Instead, the production of hydrogen gas on the Si nanowires occurs through the cleavage of Si-H bonds and the formation of Si-OH bonds, resulting in the low probability of generating oxygen. On the other hand, these two types of surface dangling bonds both extract photoexcited electrons, whose competition greatly impacts on carrier lifetime and reaction efficiency. Thus surface chemistry holds the key to achieving high efficiency in such a photocatalytic system. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Numerical modeling of isothermal compositional grading by convex splitting methods

    KAUST Repository

    Li, Yiteng

    2017-04-09

    In this paper, an isothermal compositional grading process is simulated based on convex splitting methods with the Peng-Robinson equation of state. We first present a new form of gravity/chemical equilibrium condition by minimizing the total energy which consists of Helmholtz free energy and gravitational potential energy, and incorporating Lagrange multipliers for mass conservation. The time-independent equilibrium equations are transformed into a system of transient equations as our solution strategy. It is proved our time-marching scheme is unconditionally energy stable by the semi-implicit convex splitting method in which the convex part of Helmholtz free energy and its derivative are treated implicitly and the concave parts are treated explicitly. With relaxation factor controlling Newton iteration, our method is able to converge to a solution with satisfactory accuracy if a good initial estimate of mole compositions is provided. More importantly, it helps us automatically split the unstable single phase into two phases, determine the existence of gas-oil contact (GOC) and locate its position if GOC does exist. A number of numerical examples are presented to show the performance of our method.

  3. Beyond the Interconnections: Split Manufacturing in RF Designs

    Directory of Open Access Journals (Sweden)

    Yu Bi

    2015-08-01

    Full Text Available With the globalization of the integrated circuit (IC design flow of chip fabrication, intellectual property (IP piracy is becoming the main security threat. While most of the protection methods are dedicated for digital circuits, we are trying to protect radio-frequency (RF designs. For the first time, we applied the split manufacturing method in RF circuit protection. Three different implementation cases are introduced for security and design overhead tradeoffs, i.e., the removal of the top metal layer, the removal of the top two metal layers and the design obfuscation dedicated to RF circuits. We also developed a quantitative security evaluation method to measure the protection level of RF designs under split manufacturing. Finally, a simple Class AB power amplifier and a more sophisticated Class E power amplifier are used for the demonstration through which we prove that: (1 the removal of top metal layer or the top two metal layers can provide high-level protection for RF circuits with a lower request to domestic foundries; (2 the design obfuscation method provides the highest level of circuit protection, though at the cost of design overhead; and (3 split manufacturing may be more suitable for RF designs than for digital circuits, and it can effectively reduce IP piracy in untrusted off-shore foundries.

  4. 26 CFR 1.61-22 - Taxation of split-dollar life insurance arrangements.

    Science.gov (United States)

    2010-04-01

    ... a split-dollar life insurance arrangement (or the estate or beneficiary of that party) that are not... 26 Internal Revenue 2 2010-04-01 2010-04-01 false Taxation of split-dollar life insurance..., and Taxable Income § 1.61-22 Taxation of split-dollar life insurance arrangements. (a) Scope—(1) In...

  5. Influence of the large-small split effect on strategy choice in complex subtraction.

    Science.gov (United States)

    Xiang, Yan Hui; Wu, Hao; Shang, Rui Hong; Chao, Xiaomei; Ren, Ting Ting; Zheng, Li Ling; Mo, Lei

    2018-04-01

    Two main theories have been used to explain the arithmetic split effect: decision-making process theory and strategy choice theory. Using the inequality paradigm, previous studies have confirmed that individuals tend to adopt a plausibility-checking strategy and a whole-calculation strategy to solve large and small split problems in complex addition arithmetic, respectively. This supports strategy choice theory, but it is unknown whether this theory also explains performance in solving different split problems in complex subtraction arithmetic. This study used small, intermediate and large split sizes, with each split condition being further divided into problems requiring and not requiring borrowing. The reaction times (RTs) for large and intermediate splits were significantly shorter than those for small splits, while accuracy was significantly higher for large and middle splits than for small splits, reflecting no speed-accuracy trade-off. Further, RTs and accuracy differed significantly between the borrow and no-borrow conditions only for small splits. This study indicates that strategy choice theory is suitable to explain the split effect in complex subtraction arithmetic. That is, individuals tend to choose the plausibility-checking strategy or the whole-calculation strategy according to the split size. © 2016 International Union of Psychological Science.

  6. 40 CFR 417.20 - Applicability; description of the fatty acid manufacturing by fat splitting subcategory.

    Science.gov (United States)

    2010-07-01

    ... acid manufacturing by fat splitting subcategory. 417.20 Section 417.20 Protection of Environment... POINT SOURCE CATEGORY Fatty Acid Manufacturing by Fat Splitting Subcategory § 417.20 Applicability; description of the fatty acid manufacturing by fat splitting subcategory. The provisions of this subpart are...

  7. 17 CFR 240.16a-9 - Stock splits, stock dividends, and pro rata rights.

    Science.gov (United States)

    2010-04-01

    ... 17 Commodity and Securities Exchanges 3 2010-04-01 2010-04-01 false Stock splits, stock dividends... Government Securities Dealers § 240.16a-9 Stock splits, stock dividends, and pro rata rights. The following... held as a result of a stock split or stock dividend applying equally to all securities of a class...

  8. 49 CFR 236.327 - Switch, movable-point frog or split-point derail.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Switch, movable-point frog or split-point derail..., AND APPLIANCES Interlocking Rules and Instructions § 236.327 Switch, movable-point frog or split-point derail. Switch, movable-point frog, or split-point derail equipped with lock rod shall be maintained so...

  9. Effect of superconducting electrons on the energy splitting of tunneling systems

    International Nuclear Information System (INIS)

    Yu, C.C.; Granato, A.V.

    1985-01-01

    We consider the effect of superconducting electrons on the magnitude of the energy splitting of a tunneling system. A specific example is a hydrogen atom tunneling in niobium. We find that in this case the splitting is roughly 20% smaller in the normal state than in the superconducting state. This difference in the splitting should be observable in neutron scattering and ultrasonic measurements

  10. Pump induced normal mode splittings in phase conjugation in a Kerr ...

    Indian Academy of Sciences (India)

    For sufficient strengths of the pump a normal mode splitting is demonstrated in both the specular and the phase conjugated reflectivities of the probe wave. The splitting is explained in terms of a simple model under undepleted pump approximation. Keywords. Phase conjugation; nonlinear waveguide; normal mode splitting.

  11. Signal Processing

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    Signal processing techniques, extensively used nowadays to maximize the performance of audio and video equipment, have been a key part in the design of hardware and software for high energy physics detectors since pioneering applications in the UA1 experiment at CERN in 1979

  12. A controllable growth-doping approach to synthesize bright white-light-emitting Cd:In2S3 nanocrystals.

    Science.gov (United States)

    Feng, Jian; Zhu, Hui; Yang, Xiurong

    2013-07-21

    A new type of doped Cd:In2S3 NC, which exhibits bright white-light emission with a QY of about 18%, synthesized by a one-pot G-doping synthesis approach is presented. The successful realization of temporal separation of nucleation doping and growth doping makes this approach a facile method to synthesize the In2S3/Cd:In2S3 core/shell nanostructure.

  13. The visible light photocatalytic activity enhancement of cotton cellulose nanofibers/In2S3/Ag-CdS nanocomposites

    Science.gov (United States)

    Pan, Jiaqi; Li, Jing; Zhang, Xiufang; Zheng, Yingying; Cui, Can; Zhu, Zhiyan; Li, Chaorong

    2016-07-01

    Cotton cellulose nanofibers (CCNFs)/In2S3/Ag-CdS nanocomposites were prepared by a typical technical route which combined electrospinning and a chemical method. The results showed that the CCNFs/In2S3/Ag-CdS nanocomposites had a remarkable visible light photocatalytic property and cycling stability, which displayed a significant enhancement compared with that of pure In2S3. Through analysis, this enhancement could be mainly attributed to the multilevel structure of the composites.

  14. Formation and electronic properties of In2S3/Cu(In,Ga)Se2 junctions and related thin film solar cells

    International Nuclear Information System (INIS)

    Pistor, Paul

    2009-01-01

    was shown to have a high tunneling contribution (diode quality factors of up to 6) and was associated with a mechanism located at the In 2 S 3 /Cu(In,Ga)Se 2 interface. As a result of the reduced recombination the open circuit voltage of the ZnO/ In 2 S 3 / Cu(In,Ga)Se 2 /Mo devices could be reproducibly increased by 100 mV-150 mV upon annealing and devices were fabricated with open circuit voltages beyond those of the established CdS/ Cu(In,Ga)Se 2 reference cells. By a combination of bulk and surface sensitive analysis methods, a pronounced Cu diffusion from the Cu(In,Ga)Se 2 absorber into the In 2 S 3 layer could be shown as a result of the annealing. In 2 S 3 / Cu(In,Ga)Se 2 -bilayer structures were analysed by: (1) high kinetic energy X-ray photoelectron spectroscopy (HIKE) probing the integral Cu signal of Cu in the In 2 S 3 layer, (2) standard X-ray photoelectron spectroscopy detecting the increasing Cu content at the In 2 S 3 surface and (3) energy-dispersive X-ray spectroscopy (EDX) measuring the Cu distribution in the In 2 S 3 layer. All methods gave a clear proof that Cu diffuses into the In 2 S 3 and indicated a solubility limit of 4-9 at.% for Cu in In 2 S 3 . Based on the buffer processing developed and the observed Cu diffusion, new record efficiencies for Cu(In,Ga)Se 2 solar cells with an evaporated buffer layer could be obtained. The calibration laboratory of the Fraunhofer Institut fuer Solare Energiesysteme, Freiburg, has confirmed record cell efficiencies of (15.2±0.1)% (FF=75.6%, j SC =29.8 mA/cm 2 , V OC =677 mV). (orig.)

  15. Topological entanglement entropy in Euclidean AdS3 via surgery

    Science.gov (United States)

    Luo, Zhu-Xi; Sun, Hao-Yu

    2017-12-01

    We calculate the topological entanglement entropy (TEE) in Euclidean asymptotic AdS3 spacetime using surgery. The treatment is intrinsically three-dimensional. In the BTZ black hole background, several different bipartitions are applied. For the bipartition along the horizon between two single-sided black holes, TEE is exactly the Bekenstein-Hawking entropy, which supports the ER=EPR conjecture in the Euclidean case. For other bipartitions, we derive an Entangling-Thermal relation for each single-sided black hole, which is of topological origin. After summing over genus-one classical geometries, we compute TEE in the high-temperature regime. In the case where k = 1, we find that TEE is the same as that for the Moonshine double state, given by the maximally-entangled superposition of 194 types of "anyons" in the 3d bulk, labeled by the irreducible representations of the Monster group. We propose this as the bulk analogue of the thermofield double state in the Euclidean spacetime. Comparing the TEEs between thermal AdS3 and BTZ solutions, we discuss the implication of TEE on the Hawking-Page transition in 3d.

  16. Synthesis, characterization, and assembly of beta-In2S3 nanoparticles.

    Science.gov (United States)

    Vigneashwari, B; Dash, S; Tyagi, A K; Parameswaran, P; Ravichandran, V; Sunthathiraraj, S Austin

    2007-06-01

    Semiconductor nanoparticles of Indium Sulphide were synthesized by a hydrothermal method using InCl3 and Na2S. Powder X-ray Diffraction analysis confirmed that the product obtained was nanocrystals of single-phase beta-In2S3. The crystallite size distribution was obtained from the diffraction profile and the average size was approximately 5 nm. The compositional analyses performed on the as-prepared powder showed that the material was devoid of any impurity with an In:S ratio very close to 2:3. A colloid of very fine In2S3 particles was obtained from the as-prepared powder by suspending them in acetonitrile. The optical absorption of this colloid showed evidence of strong quantum confinement of excitons and as a result the particles yielded intense photoluminescence in the violet-blue region. These colloidal particles were then electrophoretically driven on to a transparent conducting substrate to assemble into a nanostructure. A Grazing Incidence X-ray Diffraction analysis of the deposited layer revealed that the preferred orientation noticed in the native powder was removed in the deposit. The surface morphology of the deposit studied using SEM and AFM displayed an inherent ordering behaviour in the clusters organized into a two-dimensional film. The locus of the cluster lines tend to form closed circles, at the nanoscopic as well as microscopic scales, indicative of certain strong neighborhood correlations. Such structures may be expected to exhibit novel correlated properties also.

  17. Pressure-induced irreversible metallization accompanying the phase transitions in S b2S3

    Science.gov (United States)

    Dai, Lidong; Liu, Kaixiang; Li, Heping; Wu, Lei; Hu, Haiying; Zhuang, Yukai; Yang, Linfei; Pu, Chang; Liu, Pengfei

    2018-01-01

    We have revealed S b2S3 to have two phase transitions and to undergo metallization using a diamond anvil cell at around 5.0, 15.0, and 34.0 GPa, respectively. These results were obtained on the basis of high-pressure Raman spectroscopy, temperature-dependent conductivity measurements, atomic force microscopy, high-resolution transmission electron microscopy, and first-principles calculations. The first phase transition at ˜5.0 GPa is an isostructural phase transition, which is manifested in noticeable changes in five Raman-active modes and the slope of the conductivity because of a change in the electronic structure. The second pressure-induced phase transition was characterized by a discontinuous change in the slope of conductivity and a new low-intensity Raman mode at ˜15.0 GPa . Furthermore, a semiconductor-to-metal transition was found at ˜34.0 GPa , which was accompanied by irreversible metallization, and it could be attributed to the permanently plastic deformation of the interlayer spacing. This high-pressure behavior of S b2S3 will help us to understand the universal crystal structure evolution and electrical characteristics for A2B3 -type compounds, and to facilitate their application in electronic devices.

  18. Extremal solutions of the S3 model and nilpotent orbits of G2(2)

    Science.gov (United States)

    Kim, Sung-Soo; Lindman Hörnlund, Josef; Palmkvist, Jakob; Virmani, Amitabh

    2010-08-01

    We study extremal black hole solutions of the S3 model (obtained by setting S=T=U in the STU model) using group theoretical methods. Upon dimensional reduction over time, the S3 model exhibits the pseudo-Riemannian coset structure {{G} left/ {{tilde{K}}} right.} with G = G2(2) and tilde{K} = {text{S}}{{text{O}}_0}left( {2,2} right) . We study nilpotent tilde{K} -orbits of G2(2) corresponding to non-rotating single-center extremal solutions. We find six such distinct tilde{K} -orbits. Three of these orbits are supersymmetric, one is non-supersymmetric, and two are unphysical. We write general solutions and discuss examples in all four physical orbits. We show that all solutions in supersymmetric orbits when uplifted to five-dimensional minimal supergravity have single-center Gibbons-Hawking space as their four-dimensional Euclidean hyper-Kähler base space. We construct hitherto unknown extremal (supersymmetric as well as non-supersymmetric) pressureless black strings of minimal five-dimensional supergravity and briefly discuss their relation to black rings.

  19. Mechanochemically synthesized Ag2S-Sb2S3 amorphous fast ionic conductors

    International Nuclear Information System (INIS)

    Tiwari, J.P.; Shahi, K.

    2007-01-01

    The mechanochemical synthesis of (Ag 2 S) x -(Sb 2 S 3 ) 1-x amorphous fast ion conductors (a-FICs) and their structural, thermal and electrical characterizations are investigated. It is found that after ∼10 h of ball-milling, the composition 0.85Ag 2 S-Sb 2 S 3 becomes amorphous and attains a conductivity of ∼6 x 10 -3 Ω -1 cm -1 at 25 o C which is three times greater than that of the analogous melt-quenched glass. These a-FICs are found to be predominantly ionic in nature and stable under battery conditions. By examining conductivity (σ) versus composition (x), it is concluded that the sharp rise in the conductivity with the dopant Ag 2 S content is largely due to a significant increase in the mobility (μ) of Ag + ions. These results imply that the role of salts (such as Ag 2 S) is not so much to provide free (Ag + ) ions for conduction but to modify the glass structure in a manner that favours fast ion transport. It is believed that these findings will guide the development of various models to relate ion transport with glass structure

  20. Photoluminescence in Spray Pyrolysis Deposited β-In2S3 Thin Films

    Science.gov (United States)

    Jayakrishnan, R.

    2018-04-01

    Spray pyrolysis deposited In2S3 thin films exhibit two prominent photoluminescent emissions. One of the emissions is green in color and centered at around ˜ 540 nm and the other is centered at around ˜ 690 nm and is red in color. The intensity of the green emission decreases when the films are subjected to annealing in air or vacuum. The intensity of red emission increases when films are air annealed and decreases when vacuum annealed. Vacuum annealing leads to an increase in work function whereas air annealing leads to a decrease in work function for this thin film system relative to the as deposited films indicating changes in space charge regions. Surface photovoltage analysis using a Kelvin probe leads to the conclusion that inversion of band bending occurs as a result of annealing. Correlating surface contact potential measurements using a Kelvin probe, x-ray photoelectron spectroscopy and photoluminescence, we conclude that the surface passivation plays a critical role in controlling the photoluminescence from the spray pyrolysis deposited for In2S3 thin films.

  1. Simulation software support (S3) system a software testing and debugging tool

    International Nuclear Information System (INIS)

    Burgess, D.C.; Mahjouri, F.S.

    1990-01-01

    The largest percentage of technical effort in the software development process is accounted for debugging and testing. It is not unusual for a software development organization to spend over 50% of the total project effort on testing. In the extreme, testing of human-rated software (e.g., nuclear reactor monitoring, training simulator) can cost three to five times as much as all other software engineering steps combined. The Simulation Software Support (S 3 ) System, developed by the Link-Miles Simulation Corporation is ideally suited for real-time simulation applications which involve a large database with models programmed in FORTRAN. This paper will focus on testing elements of the S 3 system. In this paper system support software utilities are provided which enable the loading and execution of modules in the development environment. These elements include the Linking/Loader (LLD) for dynamically linking program modules and loading them into memory and the interactive executive (IEXEC) for controlling the execution of the modules. Features of the Interactive Symbolic Debugger (SD) and the Real Time Executive (RTEXEC) to support the unit and integrated testing will be explored

  2. ZnSnS3: Structure Prediction, Ferroelectricity, and Solar Cell Applications

    Directory of Open Access Journals (Sweden)

    Radi A. Jishi

    2016-01-01

    Full Text Available The rapid growth of the solar energy industry is driving a strong demand for high performance, efficient photoelectric materials. In particular, ferroelectrics composed of earth-abundant elements may be useful in solar cell applications due to their large internal polarization. Unfortunately, wide band gaps prevent many such materials from absorbing light in the visible to mid-infrared range. Here, we address the band gap issue by investigating the effects of substituting sulfur for oxygen in the perovskite structure ZnSnO3. Using evolutionary methods, we identify the stable and metastable structures of ZnSnS3 and compare them to those previously characterized for ZnSnO3. Our results suggest that the most stable structure of ZnSnS3 is the monoclinic structure, followed by the metastable ilmenite and lithium niobate structures. The latter structure is highly polarized, possessing a significantly reduced band gap of 1.28 eV. These desirable characteristics make it a prime candidate for solar cell applications.

  3. A split hand-split foot (SHFM3) gene is located at 10q24{yields}25

    Energy Technology Data Exchange (ETDEWEB)

    Gurrieri, F.; Genuardi, M.; Nanni, L.; Sangiorgi, E.; Garofalo, G. [Catholic Univ. of Rome (Italy)] [and others

    1996-04-24

    The split hand-split foot (SHSF) malformation affects the central rays of the upper and lower limbs. It presents either as an isolated defect or in association with other skeletal or non-skeletal abnormalities. An autosomal SHSF locus (SHFM1) was previously mapped to 7q22.1. We report the mapping of a second autosomal SHSF locus to 10q24{yields}25 region. Maximum lod scores of 3.73, 4.33 and 4.33 at a recombination fraction of zero were obtained for the loci D10S198, PAX2 and D10S1239, respectively. An 19 cM critical region could be defined by haplotype analysis and several genes with a potential role in limb morphogenesis are located in this region. Heterogeneity testing indicates the existence of at least one additional autosomal SHSF locus. 36 refs., 3 figs., 3 tabs.

  4. Synthesis of shape-controlled beta-In2S3 nanotubes through oriented attachment of nanoparticles.

    Science.gov (United States)

    Kim, Yu Hee; Lee, Jong Hak; Shin, Dong-Wook; Park, Sung Min; Moon, Jin Soo; Nam, Jung Gyu; Yoo, Ji-Beom

    2010-04-07

    Beta-In(2)S(3) nanotubes were synthesized using an organic solution pyrolysis route. The shape of the beta-In(2)S(3) nanotubes was controlled from hexagonal nanoplates to nanotubes simply by changing the reaction time. The growth mechanism of the nanotubes was explained by oriented attachment. The beta-In(2)S(3) nanotubes had a diameter, wall thickness and length of 5.0 nm, 0.79 nm and >10 microm, respectively. The diameter of the beta-In(2)S(3) nanotubes was found to be dependent on the sulfur concentration.

  5. Large-scale fabrication of In2S3 porous films via one-step hydrothermal process.

    Science.gov (United States)

    Chen, Fei; Deng, Dan; Lei, Yinlin

    2013-10-01

    Large-scale indium sulfide (In2S3) porous films were fabricated via a facile one-step and non-template hydrothermal process using L-cysteine as a capping agent. The impact of reaction conditions such as reaction time, temperatures, and capping agents on the synthesis of the In2S3 porous films were studied. The morphology, structure, and phase composition of In2S3 porous films were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), and transmission electron microscopy (TEM). The formation process and the optical property of the In2S3 porous films were also evaluated.

  6. Improving the visible light photoactivity of In2S3-graphene nanocomposite via a simple surface charge modification approach.

    Science.gov (United States)

    Yang, Min-Quan; Weng, Bo; Xu, Yi-Jun

    2013-08-20

    We report an efficient and easily accessible self-assembly route to synthesize In2S3-GR nanocomposites via electrostatic interaction of positively charged In2S3 nanoparticles with negatively charged graphene oxide (GO) followed by a hydrothermal process for reduction of GO to graphene (GR). The as-synthesized In2S3-GR nanocomposites exhibit much higher visible light photocatalytic activity toward selective reduction of nitroaromatic compounds in water than bare In2S3 nanoparticles and In2S3-GR-H that is obtained from the simple "hard" integration of GR nanosheets with solid In2S3 nanoparticles without modification of surface charge. On the basis of the joint characterizations and structure-photoactivity correlation it is disclosed that the enhanced photocatalytic performance of In2S3-GR is mainly ascribed to the more efficient interfacial contact between In2S3 and the GR nanosheets than In2S3-GR-H, which would amplify the use of electron conductivity and mobility of GR to improve the lifetime and transfer of photogenerated charge carriers more efficiently and thus boost the photoactivity more effectively. This work highlights the significant effect of preparation methods on the photoactivity of GR-semiconductor nanocomposites. It is expected that such a simple electrostatic self-assembly strategy could aid to rationally fabricate more efficient GR-semiconductor nanocomposites with improved interfacial contact and photocatalytic performance toward various photocatalytic selective transformations.

  7. Solar Water Splitting and Nitrogen Fixation with Layered Bismuth Oxyhalides.

    Science.gov (United States)

    Li, Jie; Li, Hao; Zhan, Guangming; Zhang, Lizhi

    2017-01-17

    Hydrogen and ammonia are the chemical molecules that are vital to Earth's energy, environmental, and biological processes. Hydrogen with renewable, carbon-free, and high combustion-enthalpy hallmarks lays the foundation of next-generation energy source, while ammonia furnishes the building blocks of fertilizers and proteins to sustain the lives of plants and organisms. Such merits fascinate worldwide scientists in developing viable strategies to produce hydrogen and ammonia. Currently, at the forefronts of hydrogen and ammonia syntheses are solar water splitting and nitrogen fixation, because they go beyond the high temperature and pressure requirements of methane stream reforming and Haber-Bosch reaction, respectively, as the commercialized hydrogen and ammonia production routes, and inherit the natural photosynthesis virtues that are green and sustainable and operate at room temperature and atmospheric pressure. The key to propelling such photochemical reactions lies in searching photocatalysts that enable water splitting into hydrogen and nitrogen fixation to make ammonia efficiently. Although the past 40 years have witnessed significant breakthroughs using the most widely studied TiO 2 , SrTiO 3 , (Ga 1-x Zn x )(N 1-x O x ), CdS, and g-C 3 N 4 for solar chemical synthesis, two crucial yet still unsolved issues challenge their further progress toward robust solar water splitting and nitrogen fixation, including the inefficient steering of electron transportation from the bulk to the surface and the difficulty of activating the N≡N triple bond of N 2 . This Account details our endeavors that leverage layered bismuth oxyhalides as photocatalysts for efficient solar water splitting and nitrogen fixation, with a focus on addressing the above two problems. We first demonstrate that the layered structures of bismuth oxyhalides can stimulate an internal electric field (IEF) that is capable of efficiently separating electrons and holes after their formation and of

  8. Yangian and SUSY symmetry of high spin parton splitting amplitudes in generalised Yang-Mills theory

    Science.gov (United States)

    Kirschner, Roland; Savvidy, George

    2017-07-01

    We have calculated the high spin parton splitting amplitudes postulating the Yangian symmetry of the scattering amplitudes for tensor gluons. The resulting splitting amplitudes coincide with the earlier calculations, which were based on the BCFW recursion relations. The resulting formula unifies all known splitting probabilities found earlier in gauge field theories. It describes splitting probabilities for integer and half-integer spin particles. We also checked that the splitting probabilities fulfil the generalised Kounnas-Ross 𝒩 = 1 supersymmetry relations hinting to the fact that the underlying theory can be formulated in an explicit supersymmetric manner.

  9. Investigation on morphological properties of In2S3 by high pressure x-ray diffraction

    Science.gov (United States)

    Li, Yuqiang; Wang, Qinglin; Gao, Yang; Liu, Bao; Gao, Chunxiao; Ma, Yanzhang

    2017-08-01

    In2S3 has been investigated under pressures up to 41.3 GPa at room temperature by in situ angle dispersive synchrotron x-ray diffraction in a diamond anvil cell. In the studied pressure range, the diffraction pattern can be indexed into the face centered tetragonal structure. No evident structural phase transition can be determined even with the emergence of some peaks, which can be considered as from impurity. The bulk modulus is determined to be K 0  =  37.8  ±  0.2 GPa with K‧  =  4.44  ±  0.05. In addition, we have documented a difference in the compressibility around two experiments associated with different pressure transmitting medium.

  10. Self-organization of In2S3 quantum dots into fractal nanostructures by electrophoretic deposition.

    Science.gov (United States)

    Vigneashwari, B; Tyagi, A K; Dash, S; Shankar, P; Manna, I; Suthanthiraraj, S Austin

    2009-09-01

    This paper describes the assembly of In2S3 quantum dots by electrophoretic deposition (EPD) and their subsequent self-organization into fractal nanostructures over ITO substrates. The surface morphology and the organization of these dots into nanostructures were analyzed using SEM, HRSEM and AFM techniques. These analyses reveal the existence, under appropriate conditions, of very unique nanoscale structural motifs and scale invariance associated with the assembly. Formation of such a well correlated assembly, although seems to be electric field driven, appears to be dominated by self-organizing mechanism. Such self-organized nano-scale structures consisting of cavities are likely to have fascinating condensed phase transport properties. The paper reports microscopic study of such fractal assemblies using SEM, HTSEM and AFM.

  11. Synthesis of Bi2S3 quantum dots for sensitized solar cells by reverse SILAR

    International Nuclear Information System (INIS)

    Singh, Navjot; Sharma, J.; Tripathi, S. K.

    2016-01-01

    Quantum Dot Sensitized Solar cells (QDSSC) have great potential to replace silicon-based solar cells. Quantum dots of various materials and sizes could be used to convert most of the visible light into the electrical current. This paper put emphasis on the synthesis of Bismuth Sulphide quantum dots and selectivity of the anionic precursor by Successive Ionic Layer Adsorption Reaction (SILAR). Bismuth Sulfide (Bi 2 S 3 ) (group V – Vi semiconductor) is strong contestant for cadmium free solar cells due to its optimum band gap for light harvesting. Optical, structural and electrical measurements are reported and discussed. Problem regarding the choice of precursor for anion extraction is discussed. Band gap of the synthesized quantum dots is 1.2 eV which does not match with the required energy band gap of bismuth sulfide that is 1.7 eV.

  12. Photoinduced formation of Ag nanoparticles on the surface of As2S3/Ag thin bilayer

    International Nuclear Information System (INIS)

    Binu, S; Khan, Pritam; Barik, A R; Sharma, Rituraj; Adarsh, K V; Golovchak, R; Jain, H

    2014-01-01

    In this article, we demonstrate the combined effect of photodoping and photoinduced-surface deposition in a bilayer of chalcogenide glass (ChG) and Ag as an alternative method to optically synthesize Ag nanoparticles (AgNP) on the surface of ChG. In our experiment, AgNP formation occurs through two distinct stages: In the first stage, Ag is transported through the As 2 S 3 layer as Ag + ions, and in the second stage Ag + ions are photo-deposited as AgNP. The ex situ x-ray photoelectron spectroscopy measurements and AFM observations show photoinduced Ag mass transport and the formation of AgNP. (paper)

  13. Verres thiohalogénés à base de Sb 2S 3

    Science.gov (United States)

    Tsobgny, B.; Videau, J. J.; Portier, J.; Tanguy, B.; Hagenmuller, P.

    1989-11-01

    New thiohalide glasses have been prepared in four ternary systems Sb 2S 3Hg X2Pb X2 (with X = Br, I). The characteristic temperatures ( Tg, Tc, Tf) have been determined. The observed zero-material dispersion wavelength λ0 (where {d 2n }/{dλ 2} = 0 ) and the slope of the refractive index dispersion ( {dM}/{dλ} at λ0) have been compared with the calculated values using the concepts of oscillator strength and excitation energy of Wemple. The optical transparency ranges from 0,6 to 14 μm for rich halide glasses. The theoretical optical losses have been estimated; they are quite adapted to utilization in the far-IR. Some other properties, such as chemical stability and hardness, and the dielectric constant are reported.

  14. Toric Sasaki-Einstein metrics on S2xS3

    International Nuclear Information System (INIS)

    Martelli, Dario; Sparks, James

    2005-01-01

    We show that by taking a certain scaling limit of a Euclideanised form of the Plebanski-Demianski metrics one obtains a family of local toric Kahler-Einstein metrics. These can be used to construct local Sasaki-Einstein metrics in five dimensions which are generalisations of the Y p,q manifolds. In fact, we find that these metrics are diffeomorphic to those recently found by Cvetic, Lu, Page and Pope. We argue that the corresponding family of smooth Sasaki-Einstein manifolds all have topology S 2 xS 3 . We conclude by setting up the equations describing the warped version of the Calabi-Yau cones, supporting (2,1) three-form flux

  15. The Sentinel-3 Surface Topography Mission (S-3 STM): Level 2 SAR Ocean Retracker

    Science.gov (United States)

    Dinardo, S.; Lucas, B.; Benveniste, J.

    2015-12-01

    The SRAL Radar Altimeter, on board of the ESA Mission Sentinel-3 (S-3), has the capacity to operate either in the Pulse-Limited Mode (also known as LRM) or in the novel Synthetic Aperture Radar (SAR) mode. Thanks to the initial results from SAR Altimetry obtained exploiting CryoSat-2 data, lately the interest by the scientific community in this new technology has significantly increased and consequently the definition of accurate processing methodologies (along with validation strategies) has now assumed a capital importance. In this paper, we present the algorithm proposed to retrieve from S-3 STM SAR return waveforms the standard ocean geophysical parameters (ocean topography, wave height and sigma nought) and the validation results that have been so far achieved exploiting the CryoSat-2 data as well as the simulated data. The inversion method (retracking) to extract from the return waveform the geophysical information is a curve best-fitting scheme based on the bounded Levenberg-Marquardt Least-Squares Estimation Method (LEVMAR-LSE). The S-3 STM SAR Ocean retracking algorithm adopts, as return waveform’s model, the “SAMOSA” model [Ray et al, 2014], named after the R&D project SAMOSA (led by Satoc and funded by ESA), in which it has been initially developed. The SAMOSA model is a physically-based model that offers a complete description of a SAR Altimeter return waveform from ocean surface, expressed in the form of maps of reflected power in Delay-Doppler space (also known as stack) or expressed as multilooked echoes. SAMOSA is able to account for an elliptical antenna pattern, mispointing errors in roll and yaw, surface scattering pattern, non-linear ocean wave statistics and spherical Earth surface effects. In spite of its truly comprehensive character, the SAMOSA model comes with a compact analytical formulation expressed in term of Modified Bessel functions. The specifications of the retracking algorithm have been gathered in a technical document (DPM

  16. Thickness Effect on Properties of Sprayed In2S3 Films for Photovoltaic Applications

    Science.gov (United States)

    Bouguila, N.; Kraini, M.; Halidou, I.; Lacaze, E.; Bouchriha, H.; Bouzouita, H.

    2016-01-01

    Indium sulfide (In2S3) films have been deposited on soda-lime glass substrates using a spray technique (CSP). Indium chloride and thiourea were used as precursors at a molar ratio of S:In = 2. The substrate temperature was fixed at 340°C. The effect of film thickness on the structural, morphological and optical properties of the as-deposited films has been studied. These films were characterized by x-ray diffraction, scanning electron microscopy (SEM), atomic force microscopy (AFM) and optical absorption spectroscopy. As-prepared samples were polycrystalline with a cubic structure and (400) as preferential orientation. Their grain size increased from 35 nm to 41 nm with increasing thickness whereas the dislocation density and microstrain of the films decreased with the increase of thickness. Both SEM and AFM images showed that the films were homogenous with an increase of the surface roughness with the increase of thickness. The optical transmittance of the films decreased from 80% to 20% in the visible and infrared regions when the thickness was increased from 0.78 μm to 6.09 μm. The optical band gap E g was found to be in the range of 2.75-2.19 eV and showed a decrease with film thickness. Based on the measured optical constants (n and k), a Wemple-Didomenico model was used to determine the values of single oscillator energy ( E 0), dispersion energy ( E d), optical band gap ( E g) and high frequency dielectric constant ( \\varepsilon_{∞} ). In addition, these films exhibited n-type conductivity and were highly resistive. These results confirm that In2S3 thin films are a promising alternative as a buffer-layer material for CuInGa(S,Se)2-based solar cells.

  17. [Use of the S3 guidelines for early detection of prostate cancer in urological practices].

    Science.gov (United States)

    Tiedje, D; Quer, O; Breil, B; Schrader, A J; Bothe, C; Kruse, K; Bögemann, M; Donner-Banzhoff, N; Semjonow, A

    2017-07-01

    The German S3 guideline on prostate cancer gives recommendations on early detection of prostate cancer. In this study we analyzed the adherence of urologists in private practice from the administrative district of Münster, Germany to this guideline. Data were collected through a semistructured survey of 22 urologists based on the COREQ checklist (Consolidated criteria for reporting qualitative research) in four focus groups consisting of five or six urologists in private practice. We developed 23 questions relating to 12 recommendations of the paragraphs of the S3 guidelines dealing with early detection of prostate cancer and prostate biopsy. The recommendations of the guideline are subdivided in nine "strong", one "optional recommendation" and two "statements". The adherence to the guideline was investigated by using frequency and qualitative content analysis (Mayring) based on a mixed methods design. The urologists follow six of the nine "strong recommendations" of the guideline and deviate from three. Reasons for deviations from "strong recommendations" are the following: information about advantages and disadvantages of early detection for prostate cancer, recommendation of a prostate biopsy in case of PSA level ≥4 ng/ml, and indication for repeat biopsy. Most of the "strong recommendations" are followed by the interviewed urologists of the administrative district of Münster. Contextually relevant deviations from "strong recommendations" are justified, e. g., the only limited transferability of the PSA threshold of 4 ng/ml derived from population-based studies of asymptomatic men to men presenting in a urologist's office.

  18. Sb2S3 Quantum-Dot Sensitized Solar Cells with Silicon Nanowire Photoelectrode

    Directory of Open Access Journals (Sweden)

    You-Da Hsieh

    2015-01-01

    Full Text Available We propose a novel quantum-dot sensitized solar cell (QDSSC structure that employs a quantum dot/semiconductor silicon (QD/Si coaxial nanorod array to replace the conventional dye/TiO2/TCO photoelectrode. We replaced the backlight input mode with top-side illumination and used a quantum dot to replace dye as the light-absorbing material. Photon-excited photoelectrons can be effectively transported to each silicon nanorod and conveyed to the counter electrode. We use two-stage metal-assisted etching (MAE to fabricate the micro-nano hybrid structure on a silicon substrate. We then use the chemical bath deposition (CBD method to synthesize a Sb2S3 quantum dot on the surface of each silicon nanorod to form the photoelectrode for the quantum dot/semiconductor silicon coaxial nanorod array. We use a xenon lamp to simulate AM 1.5 G (1000 W/m2 sunlight. Then, we investigate the influence of different silicon nanorod arrays and CBD deposition times on the photoelectric conversion efficiency. When an NH (N-type with high resistance silicon substrate is used, the QD/Si coaxial nanorod array synthesized by three runs of Sb2S3 deposition shows the highest photoelectric conversion efficiency of 0.253%. The corresponding short-circuit current density, open-circuit voltage, and fill factor are 5.19 mA/cm2, 0.24 V, and 20.33%, respectively.

  19. Junction formation of Cu3BiS3 investigated by Kelvin probe force microscopy and surface photovoltage measurements

    Science.gov (United States)

    Mesa, Fredy; Chamorro, William; Vallejo, William; Baier, Robert; Dittrich, Thomas; Grimm, Alexander; Lux-Steiner, Martha C

    2012-01-01

    Summary Recently, the compound semiconductor Cu3BiS3 has been demonstrated to have a band gap of ~1.4 eV, well suited for photovoltaic energy harvesting. The preparation of polycrystalline thin films was successfully realized and now the junction formation to the n-type window needs to be developed. We present an investigation of the Cu3BiS3 absorber layer and the junction formation with CdS, ZnS and In2S3 buffer layers. Kelvin probe force microscopy shows the granular structure of the buffer layers with small grains of 20–100 nm, and a considerably smaller work-function distribution for In2S3 compared to that of CdS and ZnS. For In2S3 and CdS buffer layers the KPFM experiments indicate negatively charged Cu3BiS3 grain boundaries resulting from the deposition of the buffer layer. Macroscopic measurements of the surface photovoltage at variable excitation wavelength indicate the influence of defect states below the band gap on charge separation and a surface-defect passivation by the In2S3 buffer layer. Our findings indicate that Cu3BiS3 may become an interesting absorber material for thin-film solar cells; however, for photovoltaic application the band bending at the charge-selective contact has to be increased. PMID:22497001

  20. MoS2 nanodot decorated In2S3 nanoplates: a novel heterojunction with enhanced photoelectrochemical performance.

    Science.gov (United States)

    Liu, Fangyang; Jiang, Yan; Yang, Jia; Hao, Mengmeng; Tong, Zhengfu; Jiang, Liangxing; Wu, Zhuangzhi

    2016-01-31

    MoS2 nanodot decorated In2S3 nanoplates were successfully synthesized via a modified one-pot method. The In2S3/MoS2 heterojunction nanocomposite exhibits superior optical and photoelectrochemical performance to the bare ones, owing to the synergistic effect.