WorldWideScience

Sample records for spiral grooved thrust

  1. Design and performance of compliant thrust bearing with spiral-groove membranes on resilient supports

    Science.gov (United States)

    Licht, L.; Anderson, W. J.; Doroff, S. W.

    1980-01-01

    Novel thrust bearings with spiral-groove flexible membranes mounted on resilient supports were designed and their performance demonstrated. Advantages of surface compliance were combined with the superior load-capacity of the spiral-groove geometry. Loads of 127-150N were supported on an area 42 sq cm, at speeds of 43,000-45,000 rpm and mean clearances of 15-20 microns. Support-worthiness was proved when tested in conjunction with foil journal-bearings and a 19N rotor, excited in a pitching mode by a total unbalance of 43 micron-N.

  2. Effects of Gas Rarefaction on Dynamic Characteristics of Micro Spiral-Grooved Thrust Bearing.

    Science.gov (United States)

    Liu, Ren; Wang, Xiao-Li; Zhang, Xiao-Qing

    2012-04-01

    The effects of gas-rarefaction on dynamic characteristics of micro spiral-grooved-thrust-bearing are studied. The Reynolds equation is modified by the first order slip model, and the corresponding perturbation equations are then obtained on the basis of the linear small perturbation method. In the converted spiral-curve-coordinates system, the finite-volume-method (FVM) is employed to discrete the surface domain of micro bearing. The results show, compared with the continuum-flow model, that under the slip-flow regime, the decrease in the pressure and stiffness become obvious with the increasing of the compressibility number. Moreover, with the decrease of the relative gas-film-thickness, the deviations of dynamic coefficients between slip-flow-model and continuum-flow-model are increasing.

  3. Laminar Motion of the Incompressible Fluids in Self-Acting Thrust Bearings with Spiral Grooves

    Directory of Open Access Journals (Sweden)

    Cornel Velescu

    2014-01-01

    Full Text Available We analyze the laminar motion of incompressible fluids in self-acting thrust bearings with spiral grooves with inner or external pumping. The purpose of the study is to find some mathematical relations useful to approach the theoretical functionality of these bearings having magnetic controllable fluids as incompressible fluids, in the presence of a controllable magnetic field. This theoretical study approaches the permanent motion regime. To validate the theoretical results, we compare them to some experimental results presented in previous papers. The laminar motion of incompressible fluids in bearings is described by the fundamental equations of fluid dynamics. We developed and particularized these equations by taking into consideration the geometrical and functional characteristics of these hydrodynamic bearings. Through the integration of the differential equation, we determined the pressure and speed distributions in bearings with length in the “pumping” direction. These pressure and speed distributions offer important information, both quantitative (concerning the bearing performances and qualitative (evidence of the viscous-inertial effects, the fluid compressibility, etc., for the laminar and permanent motion regime.

  4. Laminar motion of the incompressible fluids in self-acting thrust bearings with spiral grooves.

    Science.gov (United States)

    Velescu, Cornel; Popa, Nicolae Calin

    2014-01-01

    We analyze the laminar motion of incompressible fluids in self-acting thrust bearings with spiral grooves with inner or external pumping. The purpose of the study is to find some mathematical relations useful to approach the theoretical functionality of these bearings having magnetic controllable fluids as incompressible fluids, in the presence of a controllable magnetic field. This theoretical study approaches the permanent motion regime. To validate the theoretical results, we compare them to some experimental results presented in previous papers. The laminar motion of incompressible fluids in bearings is described by the fundamental equations of fluid dynamics. We developed and particularized these equations by taking into consideration the geometrical and functional characteristics of these hydrodynamic bearings. Through the integration of the differential equation, we determined the pressure and speed distributions in bearings with length in the "pumping" direction. These pressure and speed distributions offer important information, both quantitative (concerning the bearing performances) and qualitative (evidence of the viscous-inertial effects, the fluid compressibility, etc.), for the laminar and permanent motion regime.

  5. Start-stop testing of two self-acting air-lubricated spiral groove thrust bearing coatings

    Science.gov (United States)

    Dunfee, J. D.; Shapiro, W.

    1974-01-01

    Start-stop tests were conducted on air-lubricated spiral-groove thrust bearings. Application of a matrix-bonded molybdenum disulfide (MoS2) coating over a porous chrome oxide coating resulted in significantly lower friction, compared to bearings coated with chrome oxide only. The MoS2 coated bearing sustained 15,000 start-stop cycles at a maximum of 3600 rpm. Each cycle was 15 seconds on, 30 seconds off. The chrome oxide coated bearing failed by local welding after 2030 cycles. Both types of coatings exhibited early failures under higher thrust loads when operating films were insufficient to sustain the load without overheating.

  6. Performance of gas-lubricated nonconforming pivoted-pad journal bearings and a flexibly mounted spiral-groove thrust bearing

    Science.gov (United States)

    Ream, L. W.

    1973-01-01

    A test program was conducted to determine the performance characteristics of gas-lubricated nonconforming pivoted-pad journal bearings and a spiral-groove thrust bearing designed for the Brayton cycle rotating unit (BRU). Hydrostatic, hybrid (simultaneously hydrostatic and hydrodynamic), and hydrodynamic tests were conducted in argon gas at ambient pressure and temperature ranges representative of hydrostatic operation up to the 10.5-kWe BRU power-generating level. Performance of the gas lubricated bearings is presented, including hydrostatic gas flow rates, bearing clearances, bearing temperatures, and transient performance.

  7. Performance of gas-lubricated cruciform-mounted tilting-pad journal bearings and a damped flexibly mounted spiral-groove thrust bearing

    Science.gov (United States)

    Ream, L. W.

    1974-01-01

    A test program was conducted to determine the performance characteristics of gas-lubricated cruciform-mounted tilting-pad journal bearings and a damped spiral-groove thrust bearing designed for the Brayton cycle rotating unit (BRU). Hydrostatic, hybrid (simultaneously hydrostatic and hydrodynamic), and hydrodynamic tests were conducted in argon gas at ambient pressure and temperature ranges representative of operation to the 10.5 kWe BRU power-generating level. Performance of the gas lubricated bearings is presented including hydrostatic gas flow rates, bearing clearances, bearing temperatures, and transient performance.

  8. Research on performance of upstream pumping mechanical seal with different deep spiral groove

    International Nuclear Information System (INIS)

    Wang, Q; Chen, H L; Liu, T; Liu, Y H; Liu, Z B; Liu, D H

    2012-01-01

    As one new type of mechanical seal, Upstream Pumping Mechanical Seal has been widely used in fluid machinery. In this paper, structure of spiral groove is innovatively optimized to improve performance of Upstream Pumping Mechanical Seal with Spiral Groove: keeping the dam zone and the weir zone not changed, changing the bottom shape of spiral groove only, substituting different deep spiral groove for equal deep spiral groove. The simulation on Upstream Pumping Mechanical Seal with different deep spiral grooves is done using FVM method. According to calculation, the performances of opening force and pressure distribution on seals face are obtained. Five types of spiral grooves are analyzed, namely equal deep spiral groove, circumferential convergent ladder-like different deep spiral groove, circumferential divergent ladder-like different deep spiral groove, radial convergent ladder-like different deep spiral groove and radial divergent ladder-like different deep spiral groove. This paper works on twenty-five working conditions. The results indicate the performances of circumferential divergent 2-ladder different deep spiral groove are better than the others, with more opening force and better stabilization, while with the same leakage. The outcome provides theoretical support for application of Upstream Pumping Mechanical Seal with circumferential convergent ladder-like different deep spiral groove.

  9. Research on performance of upstream pumping mechanical seal with different deep spiral groove

    Science.gov (United States)

    Wang, Q.; Chen, H. L.; Liu, T.; Liu, Y. H.; Liu, Z. B.; Liu, D. H.

    2012-11-01

    As one new type of mechanical seal, Upstream Pumping Mechanical Seal has been widely used in fluid machinery. In this paper, structure of spiral groove is innovatively optimized to improve performance of Upstream Pumping Mechanical Seal with Spiral Groove: keeping the dam zone and the weir zone not changed, changing the bottom shape of spiral groove only, substituting different deep spiral groove for equal deep spiral groove. The simulation on Upstream Pumping Mechanical Seal with different deep spiral grooves is done using FVM method. According to calculation, the performances of opening force and pressure distribution on seals face are obtained. Five types of spiral grooves are analyzed, namely equal deep spiral groove, circumferential convergent ladder-like different deep spiral groove, circumferential divergent ladder-like different deep spiral groove, radial convergent ladder-like different deep spiral groove and radial divergent ladder-like different deep spiral groove. This paper works on twenty-five working conditions. The results indicate the performances of circumferential divergent 2-ladder different deep spiral groove are better than the others, with more opening force and better stabilization, while with the same leakage. The outcome provides theoretical support for application of Upstream Pumping Mechanical Seal with circumferential convergent ladder-like different deep spiral groove.

  10. Vacuum sealing with a spiral grooved gas dynamic seal

    International Nuclear Information System (INIS)

    Sawada, Tadashi

    1979-01-01

    Gas dynamic seals with rectangular spiral grooves are studied theoretically taking the effects of sidewalls of the grooves and the effects of gas compressibility into account, and slip boundary conditions are employed. The results are compared with the existing experimental data and the validity of the theory is confirmed over a wide pressure range except for the extremely low pressures. Suggestions are made regarding the choice of the geometrical dimensions, i.e., aspect ratio, helix angle, clearance parameter and groove width ratio. (author)

  11. Modeling and Analysis of the Static Characteristics and Dynamic Responses of Herringbone-grooved Thrust Bearings

    Science.gov (United States)

    Yu, Yunluo; Pu, Guang; Jiang, Kyle

    2017-12-01

    This paper describes a theoretical investigation of static and dynamic characteristics of herringbone-grooved air thrust bearings. Firstly, Finite Difference Method (FDM) and Finite Volume Method (FVM) are used in combination to solve the non-linear Reynolds equation and to find the pressure distribution of the film and the total loading capacity of the bearing. The influence of design parameters on air film gap characteristics, including the air film thickness, depth of the groove and rotating speed, are analyzed based on the FDM model. The simulation results show that hydrostatic thrust bearings can achieve a better load capacity with less air consumption than herringbone grooved thrust bearings at low compressibility number; herringbone grooved thrust bearings can achieve a higher load capacity but with more air consumption than hydrostatic thrust bearing at high compressibility number; herringbone grooved thrust bearings would lose stability at high rotating speeds, and the stability increases with the depth of the grooves.

  12. Numerical Calculation for Whirling Motion of a Centrifugal Blood Pump with Conical Spiral Groove Bearings

    Science.gov (United States)

    Shigemaru, Daichi; Tsukamoto, Hiroshi

    2010-06-01

    Whirling motion of a pump impeller was calculated for the centrifugal blood pump with Conical Spiral Groove Bearings to get a criterion for the instability of impeller whirling motion. The motion of the centrifugal blood pump impeller was calculated based on a spring damping model, and unsteady flow in the pump was computed using the commercial CFD package ANSYS CFX. Also the whirling motion of rotating impeller was measured using two displacement sensors fixed to the blood pump casing. The numerical calculations were done for the blood pump impeller with conical spiral groove bearings, and impeller whirling motion was evaluated.

  13. Evaluation of a Spiral Groove Geometry for Improvement of Hemolysis Level in a Hydrodynamically Levitated Centrifugal Blood Pump.

    Science.gov (United States)

    Murashige, Tomotaka; Kosaka, Ryo; Sakota, Daisuke; Nishida, Masahiro; Kawaguchi, Yasuo; Yamane, Takashi; Maruyama, Osamu

    2015-08-01

    The purpose of this study is to evaluate a spiral groove geometry for a thrust bearing to improve the hemolysis level in a hydrodynamically levitated centrifugal blood pump. We compared three geometric models: (i) the groove width is the same as the ridge width at any given polar coordinate (conventional model); (ii) the groove width contracts inward from 9.7 to 0.5 mm (contraction model); and (iii) the groove width expands inward from 0.5 to 4.2 mm (expansion model). To evaluate the hemolysis level, an impeller levitation performance test and in vitro hemolysis test were conducted using a mock circulation loop. In these tests, the driving conditions were set at a pressure head of 200 mm Hg and a flow rate of 4.0 L/min. As a result of the impeller levitation performance test, the bottom bearing gaps of the contraction and conventional models were 88 and 25 μm, respectively. The impeller of the expansion model touched the bottom housing. In the hemolysis test, the relative normalized index of hemolysis (NIH) ratios of the contraction model in comparison with BPX-80 and HPM-15 were 0.6 and 0.9, respectively. In contrast, the relative NIH ratios of the conventional model in comparison with BPX-80 and HPM-15 were 9.6 and 13.7, respectively. We confirmed that the contraction model achieved a large bearing gap and improved the hemolysis level in a hydrodynamically levitated centrifugal blood pump. Copyright © 2015 International Center for Artificial Organs and Transplantation and Wiley Periodicals, Inc.

  14. A novel design of spiral groove bearing in a hydrodynamically levitated centrifugal rotary blood pump.

    Science.gov (United States)

    Han, Qing; Zou, Jun; Ruan, Xiaodong; Fu, Xin; Yang, Huayong

    2012-08-01

    Good washout is very important in spiral groove bearing (SGB) designs when applied to blood pumps due to the micrometer scales of lubrication films and groove depths. To improve washout, flow rate or leakage through SGBs should be as large as possible. However, this special goal violates conventional SGB designs in which no leakage is desired as the leakage would decrease load-carrying capacity significantly. So, a design concept is formed fulfilling the two goals of high load-carrying capacity and large flow rate: let groove width decrease along flow path and the mating surface of the rotor rotate with a direction facilitating the flow through the grooves. Under this concept, a novel SGB is designed, contrary to conventional ones, with groove width decreasing with increasing spiral radius. This SGB is mounted on the motionless upper plate of our designed centrifugal blood pump, with the mating surface of rotor rotating with a direction facilitating the outward flow. To assess SGB designs, a characteristic plane is originally presented relating to pressure-normalized load-carrying capacity and flow rate. Comparisons between various kinds of SGB designs are made, and computational fluid dynamics (CFD) results are plotted in this characteristic plane from which load/flow performances can be directly read out. CFD and comparison results show that the new designs have superior load/flow characteristics. However, the impact of SGB designs upon hemolysis/thrombus formation is still to be verified according to the concept presented. © 2012, Copyright the Authors. Artificial Organs © 2012, International Center for Artificial Organs and Transplantation and Wiley Periodicals, Inc.

  15. Plasma Skimming in a Spiral Groove Bearing of a Centrifugal Blood Pump.

    Science.gov (United States)

    Murashige, Tomotaka; Sakota, Daisuke; Kosaka, Ryo; Nishida, Masahiro; Kawaguchi, Yasuo; Yamane, Takashi; Maruyama, Osamu

    2016-09-01

    Plasma skimming is a phenomenon in which discharge hematocrit is lower than feed hematocrit in microvessels. Plasma skimming has been investigated at a bearing gap in a spiral groove bearing (SGB), as this has the potential to prevent hemolysis in the SGB of a blood pump. However, it is not clear whether plasma skimming occurs in a blood pump with the SGB, because the hematocrit has not been obtained. The purpose of this study is to verify plasma skimming in an SGB of a centrifugal blood pump by developing a hematocrit measurement method in an SGB. Erythrocyte observation using a high-speed microscope and a bearing gap measurement using a laser confocal displacement meter was performed five times. In these tests, bovine blood as a working fluid was diluted with autologous plasma to adjust the hematocrit to 1.0%. A resistor was adjusted to achieve a pressure head of 100 mm Hg and a flow rate of 5.0 L/min at a rotational speed of 2800 rpm. Hematocrit on the ridge region in the SGB was measured using an image analysis based on motion image of erythrocytes, mean corpuscular volume, the measured bearing gap, and a cross-sectional area of erythrocyte. Mean hematocrit on the ridge region in the SGB was linearly reduced from 0.97 to 0.07% with the decreasing mean bearing gap from 38 to 21 μm when the rotational speed was changed from 2250 to 3000 rpm. A maximum plasma skimming efficiency of 93% was obtained with a gap of 21 μm. In conclusion, we succeeded in measuring the hematocrit on the ridge region in the SGB of the blood pump. Hematocrit decreased on the ridge region in the SGB and plasma skimming occurred with a bearing gap of less than 30 μm in the hydrodynamically levitated centrifugal blood pump. © 2016 International Center for Artificial Organs and Transplantation and Wiley Periodicals, Inc.

  16. Influence analysis of secondary O-ring seals in dynamic behavior of spiral groove gas face seals

    Science.gov (United States)

    Hu, Songtao; Huang, Weifeng; Liu, Xiangfeng; Wang, Yuming

    2016-05-01

    The current research on secondary O-ring seals used in mechanical seals has begun to focus on their dynamic properties. However, detailed analysis of the dynamic properties of O-ring seals in spiral groove gas face seals is lacking. In particular a transient study and a difference analysis of steady-state and transient performance are imperative. In this paper, a case study is performed to gauge the effect of secondary O-ring seals on the dynamic behavior (steady-state performance and transient performance) of face seals. A numerical finite element method (FEM) model is developed for the dynamic analysis of spiral groove gas face seals with a flexibly mounted stator in the axial and angular modes. The rotor tilt angle, static stator tilt angle and O-ring damping are selected to investigate the effect of O-ring seals on face seals during stable running operation. The results show that the angular factor can be ignored to save time in the simulation under small damping or undamped conditions. However, large O-ring damping has an enormous effect on the angular phase difference of mated rings, affecting the steady-state performance of face seals and largely increasing the possibility of face contact that reduces the service life of face seals. A pressure drop fluctuation is carried out to analyze the effect of O-ring seals on the transient performance of face seals. The results show that face seals could remain stable without support stiffness and O-ring damping during normal stable operation but may enter a large-leakage state when confronting instantaneous fluctuations. The oscillation-amplitude shortening effect of O-ring damping on the axial mode is much greater than that on the angular modes and O-ring damping prefers to cater for axial motion at the cost of angular motion. This research proposes a detailed dynamic-property study of O-ring seals in spiral groove gas face seals, to assist in the design of face seals.

  17. The spiral groove bearing as a mechanism for enhancing the secondary flow in a centrifugal rotary blood pump.

    Science.gov (United States)

    Amaral, Felipe; Gross-Hardt, Sascha; Timms, Daniel; Egger, Christina; Steinseifer, Ulrich; Schmitz-Rode, Thomas

    2013-10-01

    The rapid evolution of rotary blood pump (RBP) technology in the last few decades was shaped by devices with increased durability, frequently employing magnetic or hydrodynamic suspension techniques. However, the potential for low flow in small gaps between the rotor and pump casing is still a problem for hemocompatibility. In this study, a spiral groove hydrodynamic bearing (SGB) is applied with two distinct objectives: first, as a mechanism to enhance the washout in the secondary flow path of a centrifugal RBP, lowering the exposure to high shear stresses and avoiding thrombus formation; and second, as a way to allow smaller gaps without compromising the washout, enhancing the overall pump efficiency. Computational fluid dynamics was applied and verified via bench-top experiments. An optimization of selected geometric parameters (groove angle, width and depth) focusing on the washout in the gap rather than generating suspension force was conducted. An optimized SGB geometry reduced the residence time of the cells in the gap from 31 to 27 ms, an improvement of 14% compared with the baseline geometry of 200 μm without grooves. When optimizing for pump performance, a 15% smaller gap yielded a slightly better rate of fluid exchange compared with the baseline, followed by a 22% reduction in the volumetric loss from the primary pathway. Finally, an improved washout can be achieved in a pulsatile environment due to the SGB ability to pump inwardly, even in the absence of a pressure head. © 2013 Wiley Periodicals, Inc. and International Center for Artificial Organs and Transplantation.

  18. Numerical Simulation and Experimental Study on the Gas-Solid Coupling of the Aerostatic Thrust Bearing with Elastic Equalizing Pressure Groove

    Directory of Open Access Journals (Sweden)

    Zhao Xiao-long

    2017-01-01

    Full Text Available Aiming at the problem of low stiffness of aerostatic bearing, according to the principle of gas-solid coupling, this paper designs a kind of aerostatic thrust bearing with elastic equalizing pressure groove (EEPG and investigates the effect of elastic equalizing pressure groove (EEPG on the stiffness of aerostatic bearing. According to the physical model of the bearing, one deduces the deformation control equation of the elastic equalizing pressure groove and the control equation of gas lubrication, using finite difference method to derive the control equations and coupling calculation. The bearing capacity and stiffness of aerostatic bearing with EEPG in different gas film clearance are obtained. The calculation results show that the stiffness increased by 59%. The results of numerical calculation and experimental results have good consistency, proving the gas-solid coupling method can improve the bearing stiffness.

  19. Thrust stand for low-thrust liquid pulsed rocket engines

    Science.gov (United States)

    Xing, Qin; Zhang, Jun; Qian, Min; Jia, Zhen-yuan; Sun, Bao-yuan

    2010-09-01

    A thrust stand is developed for measuring the pulsed thrust generated by low-thrust liquid pulsed rocket engines. It mainly consists of a thrust dynamometer, a base frame, a connecting frame, and a data acquisition and processing system. The thrust dynamometer assembled with shear mode piezoelectric quartz sensors is developed as the core component of the thrust stand. It adopts integral shell structure. The sensors are inserted into unique double-elastic-half-ring grooves with an interference fit. The thrust is transferred to the sensors by means of static friction forces of fitting surfaces. The sensors could produce an amount of charges which are proportional to the thrust to be measured. The thrust stand is calibrated both statically and dynamically. The in situ static calibration is performed using a standard force sensor. The dynamic calibration is carried out using pendulum-typed steel ball impact technique. Typical thrust pulse is simulated by a trapezoidal impulse force. The results show that the thrust stand has a sensitivity of 25.832 mV/N, a linearity error of 0.24% FSO, and a repeatability error of 0.23% FSO. The first natural frequency of the thrust stand is 1245 Hz. The thrust stand can accurately measure thrust waveform of each firing, which is used for fine control of on-orbit vehicles in the thrust range of 5-20 N with pulse frequency of 50 Hz.

  20. DESIGN HANDBOOK ON GAS BEARINGS FOR GYROSCOPES.

    Science.gov (United States)

    consisting of a plain journal for supporting radial loads flanked by two spiral-grooved thrust bearings to support double-acting thrust loads; (3) the spiral-grooved journal bearing ; and (4) the spiral-grooved conical bearing.

  1. Logarithmic Spiral

    Indian Academy of Sciences (India)

    anti-clockwise direction and we get a right-handed spiral. (Figure 2). We know that the derivative of eX is also eX. Various properties of logarithmic spiral depend on this property of eX. Properties of Logarithmic Spiral. 1. The most important property of a logarithmic spiral is that r (i.e. the distance from the origin) increases.

  2. Tube with helical grooves for heat transfer and its fabrication process

    International Nuclear Information System (INIS)

    Yampolsky, J.S.

    1977-01-01

    The invention suggests a thermal transfer tube for use in a heat exchanger. The wall of the tube includes a certain number of spiral or helical, internal and external, grooves for the flow of the heat exchange fluids along the tube. The grooves extend for the full length of the tube. They are uniform in design and mark the internal and external spiral hollows and crests. A process for the manufacture of the heat transfer tube is also included in the invention [fr

  3. Endosonography of groove pancreatitis

    NARCIS (Netherlands)

    Tio, T. L.; Luiken, G. J.; Tytgat, G. N.

    1991-01-01

    Groove pancreatitis is a rare form of chronic pancreatitis. Distinction between pancreatitis and pancreatic carcinoma is often difficult. Two cases of groove pancreatitis diagnosed by endosonography are described. A hypoechoic pattern between the duodenal wall and pancreas was clearly imaged in both

  4. Spiral symmetry

    CERN Document Server

    Hargittai, Istvan

    1992-01-01

    From the tiny twisted biological molecules to the gargantuan curling arms of many galaxies, the physical world contains a startling repetition of spiral patterns. Today, researchers have a keen interest in identifying, measuring, and defining these patterns in scientific terms. Spirals play an important role in the growth processes of many biological forms and organisms. Also, through time, humans have imitated spiral motifs in their art forms, and invented new and unusual spirals which have no counterparts in the natural world. Therefore, one goal of this multiauthored book is to stress the c

  5. Thrust bearing

    Science.gov (United States)

    Anderson, W. J. (Inventor)

    1976-01-01

    A gas lubricated thrust bearing is described which employs relatively rigid inwardly cantilevered spokes carrying a relatively resilient annular member or annulus. This annulus acts as a beam on which are mounted bearing pads. The resilience of the beam mount causes the pads to accept the load and, with proper design, responds to a rotating thrust-transmitting collar by creating a gas film between the pads and the thrust collar. The bearing may be arranged for load equalization thereby avoiding the necessity of gimbal mounts or the like for the bearing. It may also be arranged to respond to rotation in one or both directions.

  6. Room to Groove?

    DEFF Research Database (Denmark)

    Seabrooke, Leonard

    . As long as they stay within the parameters of legitimate financial practice to signal institutional isomorphism, the `groove', creditors may well allow borrowers room for change in self-determined ways. This paper maps out the historical and conceptual terrain concerning civilizing ideas about......The use of a `standard of civilization', a preferred form of socio-political organization, in global capital markets presents both constraints and opportunities for creditors and borrowers. When imposed, civilizing standards may change how a borrower would prefer to conduct their affairs. Creditors...

  7. The spiral

    DEFF Research Database (Denmark)

    Bibace, Roger; Kharlamov, Nikita

    2013-01-01

    ’s work with Bernard Kaplan on symbol formation is a primer on this idea. This paper examines the idea of spirality and develops the notion of dynamic coexistence that can clarify the issue of directionality of development; that is, what is the general trajectory or ground plan that development assumes....... Directionality is discussed in terms of the organism-in-environment unfolding over time as the unit of developmental analysis. Thinking on this issue has proceeded from the nature–nurture debates, to recognition of the interaction of external and internal processes, to transactions between the organism...

  8. Room to Groove?

    DEFF Research Database (Denmark)

    Seabrooke, Leonard

    . As long as they stay within the parameters of legitimate financial practice to signal institutional isomorphism, the `groove', creditors may well allow borrowers room for change in self-determined ways. This paper maps out the historical and conceptual terrain concerning civilizing ideas about...... the legitimacy of financial practices within global capital markets, and investigates relationships between Western `civilizers' and Emerging Market Economies during the last two periods of financial globalization, the late-nineteenth/ early-twentieth centuries and the late-twentieth century.......The use of a `standard of civilization', a preferred form of socio-political organization, in global capital markets presents both constraints and opportunities for creditors and borrowers. When imposed, civilizing standards may change how a borrower would prefer to conduct their affairs. Creditors...

  9. EDM Electrode for Internal Grooves

    Science.gov (United States)

    Ramani, V.; Werner, A.

    1985-01-01

    Electroerosive process inexpensive alternative to broaching. Hollow brass electrodes, soldered at one end to stainless-steel holding ring, held in grooves in mandrel. These electrodes used to machine grooves electrically in stainless-steel tube three-eights inch (9.5 millimeters) in diameter. Tool used on tubes already in place in equipment.

  10. Spiral tectonics

    Science.gov (United States)

    Hassan Asadiyan, Mohammad

    2014-05-01

    Spiral Tectonics (ST) is a new window to global tectonics introduced as alternative model for Plate Tectonics (PT). ST based upon Dahw(rolling) and Tahw(spreading) dynamics. Analogues to electric and magnetic components in the electromagnetic theory we could consider Dahw and Tahw as components of geodynamics, when one component increases the other decreases and vice versa. They are changed to each other during geological history. D-component represents continental crust and T-component represents oceanic crust. D and T are two arm of spiral-cell. T-arm 180 degree lags behind D-arm so named Retard-arm with respect to D or Forward-arm. It seems primary cell injected several billions years ago from Earth's center therefore the Earth's core was built up first then mantel and finally the crust was build up. Crust building initiate from Arabia (Mecca). As the universe extended gravitation wave swirled the earth fractaly along cycloid path from big to small scale. In global scale (order-0) ST collect continents in one side and abandoned Pacific Ocean in the other side. Recent researches also show two mantels upwelling in opposite side of the Earth: one under Africa (tectonic pose) and the other under Pacific Ocean (tectonic tail). In higher order (order-1) ST build up Africa in one side and S.America in the other side therefore left Atlantic Ocean meandered in between. In order-n e.g. Khoor Musa and Bandar-Deylam bay are seen meandered easterly in the Iranian part but Khoor Abdullah and Kuwait bay meandered westerly in the Arabian part, they are distributed symmetrically with respect to axis of Persian Gulf(PG), these two are fractal components of easterly Caspian-wing and westerly Black Sea-wing which split up from Anatoly. Caspian Sea and Black Sea make two legs of Y-like structure, this shape completely fitted with GPS-velocity map which start from PG and split up in the Catastrophic Point(Anatoly). We could consider PG as remnants of Ancient Ocean which spent up

  11. CFD research on hydrodynamic gas bearings with different styles of grooves

    Science.gov (United States)

    Li, J.; Yang, S. Q.; Li, X. M.; Wu, J. H.; Li, Q.

    2017-12-01

    The gas bearing is an appealing technology which is widely used in turbo-machine in large-scale cryogenic systems for its inherent characteristic of oil-free and high-speed capability. The hydrodynamic gas bearings are more effective on cryogenic system but have less load capacity and dynamic stability by comparing with externally pressurized gas bearings. Etching some grooves on shaft or bearing is proved to be effective on improving the static and dynamic performance by experiments. The performance parameters of hydrodynamic gas bearing, such as load capacity and stiffness, are dominated by the styles and the geometric parameters of groove. In this paper, the effect of groove styles and geometric parameters on the performance parameters of hydrodynamic gas bearings is presented. And a novel style of groove is designed which can effectively improve the static and dynamic performance. The results based on the calculation of CFD show that: geometric parameters of the groove do have some influence on static and dynamic performance of hydrodynamic gas bearings, and there is an optimal objective value for each parameter of groove which makes load capacity and stiffness maximum. Compared with the spiral-style and π-style groove, the novel style of groove presented in this paper has better static performance.

  12. Optimum Design of Oil Lubricated Thrust Bearing for Hard Disk Drive with High Speed Spindle Motor

    Directory of Open Access Journals (Sweden)

    Yuta Sunami

    2013-01-01

    Full Text Available This paper presents the application of optimization method developed by Hashimoto to design oil lubricated thrust bearings for 2.5 inch form factor hard disk drives (HDD. The designing involves optimization of groove geometry and dimensions. Calculations are carried out to maximize the dynamic stiffness of the thrust bearing spindle motor. Static and dynamic characteristics of the modeled thrust bearing are calculated using the divergence formulation method. Results show that, by using the proposed optimization method, dynamic stiffness values can be well improved with the bearing geometries not being fixed to conventional grooves.

  13. Olfactory groove meningiomas.

    Science.gov (United States)

    Hentschel, Stephen J; DeMonte, Franco

    2003-06-15

    Olfactory groove meningiomas (OGMs) arise over the cribriform plate and may reach very large sizes prior to presentation. They can be differentiated from tuberculum sellae meningiomas because OGMs arise more anterior in the skull base and displace the optic nerve and chiasm inferiorly rather than superiorly. The authors searched the neurosurgery database at the M. D. Anderson Cancer Center for cases of OGM treated between 1993 and 2003. The records of these patients were then reviewed retrospectively for details regarding clinical presentation, imaging findings, surgical results and complications, and follow-up status. Thirteen patients, (12 women and one man, mean age 56 years) harbored OGMs (mean size 5.7 cm). All patients underwent bifrontal craniotomies and biorbital osteotomies. There were 11 complete resections (including the hyperostotic bone and dura of the cribriform plate and any extension into the ethmoid sinuses) and two subtotal resections with minimal residual tumor left in patients with recurrent lesions. No complication directly due to the surgery occurred in any patient. There were no recurrences in a mean follow-up period of 2 years (range 0-5 years). With current microsurgical techniques, the results of OGM resection are excellent, with a high rate of total resection and a low incidence of complications. All hyperostotic bone should be removed with the dura of the anterior skull base to minimize the risk of recurrence.

  14. DNA minor groove alkylating agents.

    Science.gov (United States)

    Denny, W A

    2001-04-01

    Recent work on a number of different classes of anticancer agents that alkylate DNA in the minor groove is reviewed. There has been much work with nitrogen mustards, where attachment of the mustard unit to carrier molecules can change the normal patterns of both regio- and sequence-selectivity, from reaction primarily at most guanine N7 sites in the major groove to a few adenine N3 sites at the 3'-end of poly(A/T) sequences in the minor groove. Carrier molecules discussed for mustards are intercalators, polypyrroles, polyimidazoles, bis(benzimidazoles), polybenzamides and anilinoquinolinium salts. In contrast, similar targeting of pyrrolizidine alkylators by a variety of carriers has little effect of their patterns of alkylation (at the 2-amino group of guanine). Recent work on the pyrrolobenzodiazepine and cyclopropaindolone classes of natural product minor groove binders is also reviewed.

  15. Optics of multiple grooves in metal

    DEFF Research Database (Denmark)

    Skjølstrup, Enok Johannes Haahr; Søndergaard, Thomas; Pedersen, Kjeld

    2017-01-01

    This paper studies theoretically how the optics of multiple grooves in a metal change as the number of grooves is increased gradually from a single groove to innitely many arranged in a periodic array. In the case of a single groove the out-of-plane scattering (OUP) cross section at resonance can...

  16. Optics of multiple grooves in metal

    DEFF Research Database (Denmark)

    Skjølstrup, Enok Johannes Haahr; Søndergaard, Thomas; Pedersen, Kjeld

    2017-01-01

    This paper theoretically studies how the optics of multiple grooves in a metal change as the number of grooves gradually increased from a single groove to infinitely many arranged in a periodic array. In the case of a single groove, the out-of-plane scattering (OUP) cross section at resonance can...

  17. Logarithmic spiral trajectories generated by Solar sails

    Science.gov (United States)

    Bassetto, Marco; Niccolai, Lorenzo; Quarta, Alessandro A.; Mengali, Giovanni

    2018-02-01

    Analytic solutions to continuous thrust-propelled trajectories are available in a few cases only. An interesting case is offered by the logarithmic spiral, that is, a trajectory characterized by a constant flight path angle and a fixed thrust vector direction in an orbital reference frame. The logarithmic spiral is important from a practical point of view, because it may be passively maintained by a Solar sail-based spacecraft. The aim of this paper is to provide a systematic study concerning the possibility of inserting a Solar sail-based spacecraft into a heliocentric logarithmic spiral trajectory without using any impulsive maneuver. The required conditions to be met by the sail in terms of attitude angle, propulsive performance, parking orbit characteristics, and initial position are thoroughly investigated. The closed-form variations of the osculating orbital parameters are analyzed, and the obtained analytical results are used for investigating the phasing maneuver of a Solar sail along an elliptic heliocentric orbit. In this mission scenario, the phasing orbit is composed of two symmetric logarithmic spiral trajectories connected with a coasting arc.

  18. Optics of multiple ultrasharp grooves in metal

    DEFF Research Database (Denmark)

    Skjølstrup, Enok Johannes Haahr; Søndergaard, Thomas

    2017-01-01

    The optics of multiple ultrasharp sub-wavelength grooves in metal is studied theoretically. Focus is on the transition from a single groove, where the scattering cross section is significant and can exceed the groove width, to infinitely many grooves in a periodic array with very low reflectance....... When the multiple-groove array is illuminated by a plane wave the out-of-plane scattering is found to be extraordinarily large compared with the expected maximum from a geometric-optics estimate even for array widths of many wavelengths. The out-of-plane scattering is even higher per groove compared...

  19. The Spiral of Euroscepticism

    DEFF Research Database (Denmark)

    Galpin, Charlotte; Trenz, Hans-Jörg

    2017-01-01

    Media scholars have increasingly examined the effects of a negativity bias that applies to political news. In the ‘spiral of cynicism’, journalist preferences for negative news correspond to public demands for sensational news. We argue that this spiral of cynicism in EU news results in a ‘spiral...

  20. Numerical Modelling and Analysis of Hydrostatic Thrust Air Bearings for High Loading Capacities and Low Air Consumption

    Science.gov (United States)

    Yu, Yunluo; Pu, Guang; Jiang, Kyle

    2017-12-01

    The paper presents a numerical simulation study on hydrostatic thrust air bearings to assess the load capacity, compressed air consumptions, and the dynamic response. Finite Difference Method (FDM) and Finite Volume Method (FVM) are combined to solve the non-linear Reynolds equation to find the pressure distribution of the air bearing gas film and the total loading capacity of the bearing. The influence of design parameters on air film gap characteristics, including the air film thickness, supplied pressure, depth of the groove and external load, are investigated based on the proposed FDM model. The simulation results show that the thrust air bearings with a groove have a higher load capacity and air consumption than without a groove, and the load capacity and air consumption both increase with the depth of the groove. Bearings without the groove are better damped than those with the grooves, and the stability of thrust bearing decreases when the groove depth increases. The stability of the thrust bearings is also affected by their loading.

  1. Improved gas thrust bearings

    Science.gov (United States)

    Anderson, W. J.; Etsion, I.

    1979-01-01

    Two variations of gas-lubricated thrust bearings extend substantially load-carrying range over existing gas bearings. Dual-Action Gas Thrust Bearing's load-carrying capacity is more than ninety percent greater than that of single-action bearing over range of compressibility numbers. Advantages of Cantilever-mounted Thrust Bearing are greater tolerance to dirt ingestion, good initial lift-off characteristics, and operational capability over wide temperature range.

  2. Triangular spiral tilings

    International Nuclear Information System (INIS)

    Sushida, Takamichi; Hizume, Akio; Yamagishi, Yoshikazu

    2012-01-01

    The topology of spiral tilings is intimately related to phyllotaxis theory and continued fractions. A quadrilateral spiral tiling is determined by a suitable chosen triple (ζ, m, n), where ζ element of D/R, and m and n are relatively prime integers. We give a simple characterization when (ζ, m, n) produce a triangular spiral tiling. When m and n are fixed, the admissible generators ζ form a curve in the unit disk. The family of triangular spiral tilings with opposed parastichy pairs (m, n) is parameterized by the divergence angle arg (ζ), while triangular spiral tilings with non-opposed parastichy pairs are parameterized by the plastochrone ratio 1/|ζ|. The generators for triangular spiral tilings with opposed parastichy pairs are not dense in the complex parameter space, while those with non-opposed parastichy pairs are dense. The proofs will be given in a general setting of spiral multiple tilings. We present paper-folding (origami) sheets that build spiral towers whose top-down views are triangular tilings. (paper)

  3. Differential diagnosis of groove pancreatic carcinomas vs. groove pancreatitis: Usefulness of the portal venous phase

    International Nuclear Information System (INIS)

    Ishigami, Kousei; Tajima, Tsuyoshi; Nishie, Akihiro; Kakihara, Daisuke; Fujita, Nobuhiro; Asayama, Yoshiki; Ushijima, Yasuhiro; Irie, Hiroyuki; Nakamura, Masafumi; Takahata, Shunichi; Ito, Tetsuhide; Honda, Hiroshi

    2010-01-01

    Purpose: To clarify if the portal venous phase is helpful for the differential diagnosis of groove pancreatic carcinomas and groove pancreatitis. Materials and methods: MDCT and MRI of groove pancreatic carcinomas (n = 7) and groove pancreatitis (n = 15) were retrospectively reviewed by two radiologists independently. The signal intensity on T2-weighted images was subjectively assessed. The presence or absence of common bile duct (CBD) and main pancreatic duct (MPD) strictures, calcifications, and cystic lesions was evaluated. Additionally, the appearance of groove pancreatic carcinoma and that of groove pancreatitis in the portal venous phase on dynamic MDCT and MRI were compared. Results: There were no significant differences in the signal intensity on T2-weighted images and in the presence or absence of CBD and MPD strictures, calcifications, and cystic lesions between groove pancreatic carcinomas and groove pancreatitis. However, patchy focal enhancement in the portal venous phase was more commonly observed in groove pancreatitis than groove pancreatic carcinoma (Reviewers 1 and 2: 14/15 [93.3%] vs. 1/7 [14.3%], P < 0.0001). In addition, peripheral enhancement was only seen in groove pancreatic carcinomas (Reviewer 1: 4/7 [57.1%] vs. 0/15 [0%], P < 0.005, and Reviewer 2: 3/7 [42.9%] vs. 0/15 [0%], P < 0.05). Conclusion: The portal venous phase may be helpful for the differential diagnosis of groove pancreatic carcinomas and groove pancreatitis.

  4. Laser grooving of surface cracks on hot work tool steel

    Directory of Open Access Journals (Sweden)

    D. Klobčar

    2011-10-01

    Full Text Available The paper presents the analysis of laser grooving of 1.2343 tool steel hardened to 46 HRC. The effect of laser power and grooving speed on groove shape (i.e. depth and width, the material removal rate and the purity of produced groove as a measure of groove quality was investigated and analyzed using response surface methodology. Optimal parameters of laser grooving were found, which enables pure grooves suitable for laser welding.

  5. Spiral Countercurrent Chromatography

    Science.gov (United States)

    Ito, Yoichiro; Knight, Martha; Finn, Thomas M.

    2013-01-01

    For many years, high-speed countercurrent chromatography conducted in open tubing coils has been widely used for the separation of natural and synthetic compounds. In this method, the retention of the stationary phase is solely provided by the Archimedean screw effect by rotating the coiled column in the centrifugal force field. However, the system fails to retain enough of the stationary phase for polar solvent systems such as the aqueous–aqueous polymer phase systems. To address this problem, the geometry of the coiled channel was modified to a spiral configuration so that the system could utilize the radially acting centrifugal force. This successfully improved the retention of the stationary phase. Two different types of spiral columns were fabricated: the spiral disk assembly, made by stacking multiple plastic disks with single or four interwoven spiral channels connected in series, and the spiral tube assembly, made by inserting the tetrafluoroethylene tubing into a spiral frame (spiral tube support). The capabilities of these column assemblies were successfully demonstrated by separations of peptides and proteins with polar two-phase solvent systems whose stationary phases had not been well retained in the earlier multilayer coil separation column for high-speed countercurrent chromatography. PMID:23833207

  6. Spiral finned crucible pot

    Science.gov (United States)

    Soemowidagdo, Arianto Leman; Tiwan, Widarto, Ardian, Aan

    2018-02-01

    Innovation on a crucible furnace to increase its efficiency in aluminum melting has been done. The innovation was a spiral finned crucible pot. The inclination of the spiral finned was vary of 5, 10, 15, and 20 degrees. The spiral finned effects was determined from the performance test result. A crucible pot without fin was also tested as a control. The crucible pot was examined at the same process condition. The crucible pot with the inclined fin of 10 degrees gives an optimum performance. It gives effective heating rate so that more efficient in LPG consumption. Therefore it saves energy in the aluminum melting process.

  7. Thermal Bridge Effects in Window Grooves

    DEFF Research Database (Denmark)

    Rose, Jørgen

    1997-01-01

    In this report thermal bridge effects in window grooves are analyzed. The analysis is performed using different thicknesses of the window groove insulation, to evaluate what the optimal solution is.All analysis in the report is performed using both 2- and 3-dimensional numerical analysis....

  8. Mixed convection in a baffled grooved channel

    Indian Academy of Sciences (India)

    In the present numerical work, flow structure and heat transfer characteristics are investigated in a baffled grooved channel, differentially heated from the sides. The baffle is placed vertically downward from the top wall of grooved channel geometry, with the motive of diverting outside forced flow towards the inside of the ...

  9. Spiral 2 Week

    International Nuclear Information System (INIS)

    2007-01-01

    The main goal of this meeting is to present and discuss the current status of the Spiral-2 project at GANIL in front of a large community of scientists and engineers. Different issues have been tackled particularly the equipment around Spiral-2 like injectors, cryo-modules or beam diagnostics, a workshop was devoted to other facilities dedicated to radioactive ion beam production. This document gathers only the slides of the presentations

  10. Spiral 2 Week

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2007-07-01

    The main goal of this meeting is to present and discuss the current status of the Spiral-2 project at GANIL in front of a large community of scientists and engineers. Different issues have been tackled particularly the equipment around Spiral-2 like injectors, cryo-modules or beam diagnostics, a workshop was devoted to other facilities dedicated to radioactive ion beam production. This document gathers only the slides of the presentations.

  11. The investigation of groove geometry effect on heat transfer for internally grooved tubes

    International Nuclear Information System (INIS)

    Bilen, Kadir; Cetin, Murat; Gul, Hasan; Balta, Tuba

    2009-01-01

    An experimental study of surface heat transfer and friction characteristics of a fully developed turbulent air flow in different grooved tubes is reported. Tests were performed for Reynolds number range 10,000-38,000 and for different geometric groove shapes (circular, trapezoidal and rectangular). The ratio of tube length-to-diameter is 33. Among the grooved tubes, heat transfer enhancement is obtained up to 63% for circular groove, 58% for trapezoidal groove and 47% for rectangular groove, in comparison with the smooth tube at the highest Reynolds number (Re = 38,000). Correlations of heat transfer and friction coefficient were obtained for different grooved tubes. In evaluation of thermal performance, it is seen that the grooved tubes are thermodynamically advantageous (Ns, a < 1) up to Re = 30,000 for circular and trapezoidal grooves and up to Re = 28,000 for rectangular grooves. It is observed that there is an optimum value of the entropy generation number at about Re = 17,000 for all investigated grooves

  12. A Survey for Transverse Nasal Groove

    Directory of Open Access Journals (Sweden)

    K Pavithran

    1989-01-01

    Full Text Available Out of 3000 consecutive subjects surveyed for the typical lesion of transverse nasal groove, 180 were found to have the characteristic lesions. In LU patients, the floor of the groove was studded with patulous hair follicles, greasy sale and black comedones. The age of the patients varied from 16 to 45 years, the majority belonged to the 20 to 30 age group. Family occurrence of the groove was noted ′in only 7.Seboffhoeic dermatitis, pityriasis versicolor and acne vulgaris were the commonly associated diseases.

  13. Plasma Generator Using Spiral Conductors

    Science.gov (United States)

    Szatkowski, George N. (Inventor); Dudley, Kenneth L. (Inventor); Ticatch, Larry A. (Inventor); Smith, Laura J. (Inventor); Koppen, Sandra V. (Inventor); Nguyen, Truong X. (Inventor); Ely, Jay J. (Inventor)

    2016-01-01

    A plasma generator includes a pair of identical spiraled electrical conductors separated by dielectric material. Both spiraled conductors have inductance and capacitance wherein, in the presence of a time-varying electromagnetic field, the spiraled conductors resonate to generate a harmonic electromagnetic field response. The spiraled conductors lie in parallel planes and partially overlap one another in a direction perpendicular to the parallel planes. The geometric centers of the spiraled conductors define endpoints of a line that is non-perpendicular with respect to the parallel planes. A voltage source coupled across the spiraled conductors applies a voltage sufficient to generate a plasma in at least a portion of the dielectric material.

  14. The spinning ball spiral

    Science.gov (United States)

    Dupeux, Guillaume; Le Goff, Anne; Quéré, David; Clanet, Christophe

    2010-09-01

    We discuss the trajectory of a fast revolving solid ball moving in a fluid of comparable density. As the ball slows down owing to drag, its trajectory follows an exponential spiral as long as the rotation speed remains constant: at the characteristic distance L where the ball speed is significantly affected by the drag, the bending of the trajectory increases, surprisingly. Later, the rotation speed decreases, which makes the ball follow a second kind of spiral, also described in the paper. Finally, the use of these highly curved trajectories is shown to be relevant to sports.

  15. Quarkyonic Chiral Spirals

    International Nuclear Information System (INIS)

    Toru, Kojo; Hidaka, Y.; Pisarski, R.; McLerran, L.

    2010-01-01

    We argue the properties of confining dense quark matter, 'quarkyonic' matter, from the viewpoint of both bulk properties and excitation modes. After a brief review of confining aspects, the chiral breaking/restoration will be discussed. We argue that the strong infrared correlations induce the chiral spiral, i.e., the spatial modulation of the chiral condensate which breaks the chiral symmetry locally but restore it globally. The effective dimensional reduction takes place, allowing us to analyzing the system as 2D model in which several exact results can be explicitly derived. We also discuss the excitation spectra, both mesonic and baryonic ones, on the chiral spiral. (author)

  16. Two pad axially grooved hydrostatic bearing

    Science.gov (United States)

    San Andres, Luis A. (Inventor)

    1995-01-01

    A hydrostatic bearing having two axial grooves on opposite sides of the bearing for breaking the rotational symmetry in the dynamic force coefficients thus reducing the whirl frequency ratio and increasing the damping and stiffness of the hydrostatic bearing.

  17. Experimental Studies on Grooved Double Pipe Heat Exchanger with Different Groove Space

    Science.gov (United States)

    Sunu, P. W.; Arsawan, I. M.; Anakottapary, D. S.; Santosa, I. D. M. C.; Yasa, I. K. A.

    2018-01-01

    Experimental studies were performed on grooved double pipe heat exchanger (DPHE) with different groove space. The objective of this work is to determine optimal heat transfer parameter especially logarithmic mean temperature difference (LMTD). The document in this paper also provides the total heat observed by the cold fluid. The rectangular grooves were incised on outer surface of tube side with circumferential pattern and two different grooves space, namely 1 mm and 2 mm. The distance between grooves and the grooves high were kept constant, 8 mm and 0.3 mm respectively. The tube diameter is 20 mm and its made of aluminium. The shell is made of acrylic which has 28 mm in diameter. Water is used as the working fluid. Using counter flow scheme, the cold fluid flows in the annulus room of DPHE. The volume flowrate of hot fluid remains constant at 15 lpm. The volume flowrate of cold fluid were varied from 11 lpm to 15 lpm. Based on logarithmic mean temperature difference analysis, the LMTD of 1 mm grooves space was higher compared to that of 2 mm grooves space. The smaller grooves space has more advantage since the recirculating region are increased which essentially cause larger heat transfer enhancement.

  18. Groove pressing and its research progress

    Directory of Open Access Journals (Sweden)

    Zongshen WANG

    2017-06-01

    Full Text Available In order to systematically study the application of groove pressing in preparing bulk mass ultra-fine grain sheet metal, the fundamental principles, plastic mechanics analysis and classification of groove pressing are introduced, and on the basis of which, the influence rules and mechanism of processing factors such as pass number, deformation temperature and die structure on groove pressing are reviewed, and some key problems such as thermal stability of processed materials, process improvements and deformation path, deformation homogeneity analysis and process optimization are summarized. The research trends of groove pressing in the fields of application to sheet metals difficult to deform at room temperature, improvement of ductility, toughness and formability of processed sheets as well as its plastic deformation mechanism are prospected: in the future, groove pressing will be used for sheet metals which have limited formability but wide industrial applications such as magnesium alloys and titanium alloys, and much attention should be paid to investigation on performance adjustment mechanism and methods for processed sheets and exploration of effective technological measures for preventing cracks; meanwhile, the evolution mechanism of microstructure and properties of groove pressed materials must be systematically and thoroughly revealed.

  19. Minimum fuel trajectories for a low-thrust power-limited mission to the moon and to Lagrange points L4 and L5

    Science.gov (United States)

    Breakwell, John V.; Golan, Oded M.

    1990-01-01

    Minimum fuel trajectories from a low earth parking orbit to Lagrange points L4 or L5 and to the moon are obtained for a low-thrust limited-power spacecraft, with thrust acceleration levels of the order of 0.001 G. The procedure to find a trajectory to the libration point starts from an analytical description of a slightly elliptical spiral, given by Breakwell and Rauch. The earth moon trajectory is found by matching an earth spiral to a moon spiral on the sphere of influence. Earth oblateness effect is considered.

  20. Tracking Target and Spiral Waves

    DEFF Research Database (Denmark)

    Jensen, Flemming G.; Sporring, Jon; Nielsen, Mads

    2002-01-01

    A new algorithm for analyzing the evolution of patterns of spiral and target waves in large aspect ratio chemical systems is introduced. The algorithm does not depend on finding the spiral tip but locates the center of the pattern by a new concept, called the spiral focus, which is defined by the...

  1. Are spiral galaxies heavy smokers?

    International Nuclear Information System (INIS)

    Davies, J.; Disney, M.; Phillipps, S

    1990-01-01

    The dustiness of spiral galaxies is discussed. Starburst galaxies and the shortage of truly bright spiral galaxies is cited as evidence that spiral galaxies are far dustier than has been thought. The possibility is considered that the dust may be hiding missing mass

  2. Spiraling into Transformative Learning

    Science.gov (United States)

    Cranton, Patricia

    2010-01-01

    This article explores how technical and vocational learning may spiral into transformative learning. Transformative learning theory is reviewed and the learning tasks of critical theory are used to integrate various approaches to transformative learning. With this as a foundation, the article explores how transformative learning can be fostered in…

  3. Archimedean Voronoi spiral tilings

    Science.gov (United States)

    Yamagishi, Yoshikazu; Sushida, Takamichi

    2018-01-01

    We study the transition of the number of spirals (called parastichy in the theory of phyllotaxis) within a Voronoi tiling for Archimedean spiral lattices. The transition of local parastichy numbers within a tiling is regarded as a transition at the base site point in a continuous family of tilings. This gives a natural description of the quasiperiodic structure of the grain boundaries. It is proved that the number of tiles in the grain boundaries are denominators of rational approximations of the argument (called the divergence angle) of the generator. The local parastichy numbers are non-decreasing functions of the plastochron parameter. The bifurcation diagram of local parastichy numbers has a Farey tree structure. We also prove Richards’ formula of spiral phyllotaxis in the case of Archimedean Voronoi spiral tilings, and show that, if the divergence angle is a quadratic irrational number, then the shapes of tiles in the grain boundaries are close to rectangles. If the divergence angle is linearly equivalent to the golden section, then the shape of tiles in the grain boundaries is close to square.

  4. Properties of spiral resonators

    International Nuclear Information System (INIS)

    Haeuser, J.

    1989-10-01

    The present thesis deals with the calculation and the study of the application possibilities of single and double spiral resonators. The main aim was the development and the construction of reliable and effective high-power spiral resonators for the UNILAC of the GSI in Darmstadt and the H - -injector for the storage ring HERA of DESY in Hamburg. After the presentation of the construction and the properties of spiral resonators and their description by oscillating-circuit models the theoretical foundations of the bunching are presented and some examples of a rebuncher and debuncher and their influence on the longitudinal particle dynamics are shown. After the description of the characteristic accelerator quantities by means of an oscillating-circuit model and the theory of an inhomogeneous λ/4 line it is shown, how the resonance frequency and the efficiency of single and double spiral resonators can be calculated from the geometrical quantities of the structure. In the following the dependence of the maximal reachable resonator voltage in dependence on the gap width and the surface of the drift tubes is studied. Furthermore the high-power resonators are presented, which were built for the different applications for the GSI in Darmstadt, DESY in Hamburg, and for the FOM Institute in Amsterdam. (orig./HSI) [de

  5. Robust control for constant thrust rendezvous under thrust failure

    Directory of Open Access Journals (Sweden)

    Qi Yongqiang

    2015-04-01

    Full Text Available A robust constant thrust rendezvous approach under thrust failure is proposed based on the relative motion dynamic model. Firstly, the design problem is cast into a convex optimization problem by introducing a Lyapunov function subject to linear matrix inequalities. Secondly, the robust controllers satisfying the requirements can be designed by solving this optimization problem. Then, a new algorithm of constant thrust fitting is proposed through the impulse compensation and the fuel consumption under the theoretical continuous thrust and the actual constant thrust is calculated and compared by using the method proposed in this paper. Finally, the proposed method having the advantage of saving fuel is proved and the actual constant thrust switch control laws are obtained through the isochronous interpolation method, meanwhile, an illustrative example is provided to show the effectiveness of the proposed control design method.

  6. Static characteristic analysis and experimental research of aerostatic thrust bearing with annular elastic uniform pressure plate

    Directory of Open Access Journals (Sweden)

    Hao Dong

    2015-03-01

    Full Text Available In this article, an aerostatic thrust bearing with annular elastic uniform pressure plate structure was designed. In order to obtain a relationship between bearing capacity and stiffness of aerostatic thrust bearing designed in this article, first, the stress field mechanics model of the gas thrust bearing was established in the static. Second, deformation control equations of the elastic uniform pressure plate and gas lubrication Reynolds equation were established according to the flow continuity principle. Here, finite element mesh of gas flow field was woven using the technology of grid overlapping and grid stitching. Then, gas–solid coupling control equations were solved using the numerical method. Gas film pressure distribution and gas static bearing capacity of thrust bearing were analyzed. Function relationship between bearing capacity and the stiffness and the thickness of gas film was obtained. Finally, the results of theory analysis and experiment were compared. The results of the comparison can be listed as, under the effect of gas pressure, orifice area and the equilibrium pressure groove depth are changed due to elastic deformation of the elastic uniform pressure plate. The static stiffness of aerostatic thrust bearing with elastic equilibrium pressure groove increased by 30% than the static stiffness of aerostatic thrust bearing with rigid equilibrium pressure groove. The maximum carrying capacity occurred in the gas film thickness of 3.5 µm. The maximum static stiffness appeared in the gas film thickness of 5.5 µm. It can be seen from the comparison results of experiments and theoretical analysis that data results of gas film thickness and the bearing capacity are the same. The feasibility of the theoretical analysis method is validated.

  7. Theory of spiral structure

    International Nuclear Information System (INIS)

    Lin, C.C.

    1977-01-01

    The density wave theory of galactic spirals has now developed into a form suitable for consideration by experts in Applied Mechanics. On the one hand, comparison of theoretical deductions with observational data has convinced astrophysicists of the validity of the basic physical picture and the calculated results. On the other hand, the dynamical problems of a stellar system, such as those concerning the origin of spiral structure in galaxies, have not been completely solved. This paper reviews the current status of such developments, including a brief summary of comparison with observations. A particularly important mechanism, currently called the mechanism of energy exchange, is described in some detail. The mathematical problems and the physical processes involved are similar to those occurring in certain instability mechanisms in the 'magnetic bottle' designed for plasma containment. Speculations are given on the future developments of the theory and on observational programs. (Auth.)

  8. Spiral 2 workshop

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-07-01

    The accelerator and experimental facilities at GANIL will be transformed over the next 5-10 years. The centerpiece of the additions to the accelerator complex will be Spiral-2. This is the first phase of a new radioactive beam facility based on the ISOL principle. The main aim of Spiral-2 will be to produce intense, high quality beams of neutron-rich nuclei created in neutron-induced fission of heavy elements and accelerated by the existing CIME cyclotron. The principal aims of this workshop will be a) to publicize the new facilities, b) to discuss and define the science which might be carried out with them, c) to discuss the instrumentation and infrastructure required to exploit the new facilities and d) to help form collaborations of scientists wishing to design and construct the equipment needed to undertake the science programme. This document gathers most of the slides presented in the workshop.

  9. Lateral dampers for thrust bearings

    Science.gov (United States)

    Hibner, D. H.; Szafir, D. R.

    1985-01-01

    The development of lateral damping schemes for thrust bearings was examined, ranking their applicability to various engine classes, selecting the best concept for each engine class and performing an in-depth evaluation. Five major engine classes were considered: large transport, military, small general aviation, turboshaft, and non-manrated. Damper concepts developed for evaluation were: curved beam, constrained and unconstrained elastomer, hybrid boost bearing, hydraulic thrust piston, conical squeeze film, and rolling element thrust face.

  10. Graphene Plasmons in Triangular Wedges and Grooves

    DEFF Research Database (Denmark)

    Gonçalves, P. A. D.; Dias, E. J. C.; Xiao, Sanshui

    2016-01-01

    and tunability of graphene plasmons guided along the apex of a graphene-covered dielectric wedge or groove. In particular, we present a quasi-analytic model to describe the plasmonic eigenmodes in such a system, including the complete determination of their spectrum and corresponding induced potential...... and electric-field distributions. We have found that the dispersion of wedge/groove graphene plasmons follows the same functional dependence as their flat-graphene plasmon counterparts, but now scaled by a (purely) geometric factor in which all the information about the system’s geometry is contained. We...

  11. High Thrust & High ISP Nuclear Thermal Rocket (NTR) Grooved Ring Fuel Element (GRFE)

    Data.gov (United States)

    National Aeronautics and Space Administration — Missions to Mars will benefit from propulsion systems with performance levels exceeding that of today's best chemical engines. Nuclear Thermal Rocket (NTR)...

  12. Spirality: A Noval Way to Measure Spiral Arm Pitch Angle

    Science.gov (United States)

    Shields, Douglas W.; Boe, Benjamin; Henderson, Casey L.; Hartley, Matthew; Davis, Benjamin L.; Pour Imani, Hamed; Kennefick, Daniel; Kennefick, Julia D.

    2015-01-01

    We present the MATLAB code Spirality, a novel method for measuring spiral arm pitch angles by fitting galaxy images to spiral templates of known pitch. For a given pitch angle template, the mean pixel value is found along each of typically 1000 spiral axes. The fitting function, which shows a local maximum at the best-fit pitch angle, is the variance of these means. Error bars are found by varying the inner radius of the measurement annulus and finding the standard deviation of the best-fit pitches. Computation time is typically on the order of 2 minutes per galaxy, assuming at least 8 GB of working memory. We tested the code using 128 synthetic spiral images of known pitch. These spirals varied in the number of spiral arms, pitch angle, degree of logarithmicity, radius, SNR, inclination angle, bar length, and bulge radius. A correct result is defined as a result that matches the true pitch within the error bars, with error bars no greater than ±7°. For the non-logarithmic spiral sample, the correct answer is similarly defined, with the mean pitch as function of radius in place of the true pitch. For all synthetic spirals, correct results were obtained so long as SNR > 0.25, the bar length was no more than 60% of the spiral's diameter (when the bar was included in the measurement), the input center of the spiral was no more than 6% of the spiral radius away from the true center, and the inclination angle was no more than 30°. The synthetic spirals were not deprojected prior to measurement. The code produced the correct result for all barred spirals when the measurement annulus was placed outside the bar. Additionally, we compared the code's results against 2DFFT results for 203 visually selected spiral galaxies in GOODS North and South. Among the entire sample, Spirality's error bars overlapped 2DFFT's error bars 64% of the time. For those galaxies in which Source code is available by email request from the primary author.

  13. Band-notched spiral antenna

    Energy Technology Data Exchange (ETDEWEB)

    Jeon, Jae; Chang, John

    2018-03-13

    A band-notched spiral antenna having one or more spiral arms extending from a radially inner end to a radially outer end for transmitting or receiving electromagnetic radiation over a frequency range, and one or more resonance structures positioned adjacent one or more segments of the spiral arm associated with a notch frequency band or bands of the frequency range so as to resonate and suppress the transmission or reception of electromagnetic radiation over said notch frequency band or bands.

  14. Three phase spiral liver Scanning

    International Nuclear Information System (INIS)

    Kanyanja, T.A.

    2006-01-01

    The ability to perform rapid back-to-back spiral acquisitions is an important recent technical advantage of spiral CT. this allows imaging of the upper abdomen (liver) during peak arterial enhancement (arterial phase) and during peak hepatic parenchymal enhancement (portal venous phase). Breatheld spiral CT has completely replaced dynamic incremental CT for evaluation of the liver. in selected patients with hyper vascular metastasis (hepatoma, neuroendocrine tumors, renal cell carcinoma, etc.) a biphasic examination is performed with one spiral acquisition obtained during the hepatic arterial phase and a second acquisition during the portal venous phase

  15. Neighbourhood Abstraction in GROOVE - Tool Paper

    NARCIS (Netherlands)

    Rensink, Arend; Zambon, Eduardo; de Lara, Juan; Varro, Daniel

    In this paper we discuss the implementation of neighbourhood graph abstraction in the GROOVE tool set. Important classes of graph grammars may have unbounded state spaces and therefore cannot be verified with traditional model checking techniques. One way to address this problem is to perform graph

  16. Mixed convection in a baffled grooved channel

    Indian Academy of Sciences (India)

    For the present study, external flow from both left and right of the grooved channel are considered. A remarkable enhancement of heat transfer is observed in presence of baffle. The study has also pointed out that for optimal performance, the position and height of the baffle need to be adjusted depending on the direction of ...

  17. Groove pancreatic carcinomas: radiological and pathological findings

    Energy Technology Data Exchange (ETDEWEB)

    Gabata, Toshifumi; Terayama, Noboru; Sanada, Junichiro; Kobayashi, Satoshi; Matsui, Osamu [Department of Radiology, Kanazawa University, School of Medicine, 13-1 Takara-machi, Kanazawa City 920-8641 (Japan); Kadoya, Masumi [Department of Radiology, Kanazawa University, School of Medicine, 13-1 Takara-machi, Kanazawa City 920-8641 (Japan); Department of Radiology, School of Medicine, Shinshu University, Shinshu 390-8621 (Japan)

    2003-07-01

    The aim of this study was to clarify the characteristics of pancreatic head carcinomas mainly invading the groove between the duodenum and the pancreatic head. Nine patients with pathologically proven pancreatic head carcinomas underwent thin-slice dynamic CT, MR imaging, duodenal endoscopy, and angiography (seven patients). Plate-like masses within the groove region were seen in all cases, which showed hypointensity on T1-weighted images and slight hyperintensity on T2-weighted MR images. The masses appeared hypovascular in the early phase and delayed enhancement in the late phase of dynamic CT and MR imaging. On MR cholangiopancreatography, stenosis of intrapancreatic common bile duct was seen in all patients, whereas stenosis of the main pancreatic duct was seen in only three cases. Endoscopy revealed luminal narrowing of the duodenum in all patients, and duodenal mucosal biopsy demonstrated adenocarcinoma in seven patients. Abdominal arteriography showed serrated encasement of peripancreatic arteries in seven patients who received angiographic examinations. The CT and MR imaging findings of groove pancreatic carcinomas resemble those of groove pancreatitis. Differential diagnosis may be achieved by the pathological diagnosis of a biopsy specimen of the duodenal mucosa and arterial encasement on arteriography. (orig.)

  18. Appraisal of transverse nasal groove: A study

    Directory of Open Access Journals (Sweden)

    Belagola D Sathyanarayana

    2012-01-01

    Full Text Available Background: Transverse nasal groove is a condition of cosmetic concern which awaits due recognition and has been widely described as a shallow groove that extends transversely over the dorsum of nose. However, we observed variations in the clinical presentations of this entity, hitherto undescribed in literature. Aims: We conducted a clinicoepidemiological study of transverse nasal lesions in patients attending our outpatient department. Methods: We conducted a prospective observational study. We screened all patients attending our out-patient department for presence of transverse nasal lesions, signs of any dermatosis and associated other skin conditions. Results: One hundred patients were recruited in the study. Females (80% predominated over males. Most patients were of 15-45 years age group (70%. Majority of the transverse nasal lesions were classical transverse nasal groove (39% and others included transverse nasal line (28%, strip (28%, ridge (4% and loop (1%. Seborrhoeic diathesis was the most common condition associated with transverse nasal lesion. Conclusions: Occurrence of transverse nasal line, strip, ridge and loop, in addition to classical transverse nasal groove implies that latter is actually a subset of transverse nasal lesions. Common association of this entity with seborrheic dermatitis, seborrhea and dandruff raises a possibility of whether transverse nasal lesion is a manifestation of seborrheic diathesis.

  19. Mixed convection in a baffled grooved channel

    Indian Academy of Sciences (India)

    A remarkable enhancement of heat transfer is observed in presence of baffle. The study has also pointed out that for optimal performance, the position and height of the baffle need to be adjusted depending on the direction of external flow. Keywords. Heat transfer; grooved channel; mixed convection; Richardson number;.

  20. Optimization of Grooved Micromixer for Microengineering Technologies

    DEFF Research Database (Denmark)

    Sabotin, I.; Tristo, G.; Bissacco, Giuliano

    2013-01-01

    with a modified Slanted Groove Micromixer (SGM). A SGM prototype was machined by micro electrical discharge milling (EDM) technology. The simulation results were experimentally verified with flow visualization and a good agreement was observed. Due to simple 2.5D geometry and efficient mixing properties...

  1. The subtropical nutrient spiral

    Science.gov (United States)

    Jenkins, William J.; Doney, Scott C.

    2003-12-01

    We present an extended series of observations and more comprehensive analysis of a tracer-based measure of new production in the Sargasso Sea near Bermuda using the 3He flux gauge technique. The estimated annually averaged nitrate flux of 0.84 ± 0.26 mol m-2 yr-1 constitutes only that nitrate physically transported to the euphotic zone, not nitrogen from biological sources (e.g., nitrogen fixation or zooplankton migration). We show that the flux estimate is quantitatively consistent with other observations, including decade timescale evolution of the 3H + 3He inventory in the main thermocline and export production estimates. However, we argue that the flux cannot be supplied in the long term by local diapycnal or isopycnal processes. These considerations lead us to propose a three-dimensional pathway whereby nutrients remineralized within the main thermocline are returned to the seasonally accessible layers within the subtropical gyre. We describe this mechanism, which we call "the nutrient spiral," as a sequence of steps where (1) nutrient-rich thermocline waters are entrained into the Gulf Stream, (2) enhanced diapycnal mixing moves nutrients upward onto lighter densities, (3) detrainment and enhanced isopycnal mixing injects these waters into the seasonally accessible layer of the gyre recirculation region, and (4) the nutrients become available to biota via eddy heaving and wintertime convection. The spiral is closed when nutrients are utilized, exported, and then remineralized within the thermocline. We present evidence regarding the characteristics of the spiral and discuss some implications of its operation within the biogeochemical cycle of the subtropical ocean.

  2. Coupled Bending-Torsional Nonlinear Vibration and Bifurcation Characteristics of Spiral Bevel Gear System

    Directory of Open Access Journals (Sweden)

    Jinli Xu

    2017-01-01

    Full Text Available A spiral bevel gear system supported on thrust bearings considering the coupled bending-torsional nonlinear vibration is proposed and an eight degrees of freedom (8DOF lumped parameter dynamic model of the spiral bevel gear system combined with time-varying stiffness, static transmission error, gear backlash, and bearing clearances is investigated. The spiral bevel gear system is analyzed with the equations of motion and the dynamic response is solved using the Runge-Kutta method. The effects of mesh frequency, mesh damping coefficient, load coefficient, and gear backlash are revealed, which describe the true mesh characteristics of the spiral bevel gear system. The bifurcation characteristics as jump discontinuities, periodic windows, and chaos are obtained by studying time histories, phase plane portraits, Poincaré maps, Fourier spectra, and global bifurcation diagrams of the gear system. The results presented in this study provide some useful information for engineers in designing and controlling such gear systems.

  3. Optimum Groove Location of Hydrodynamic Journal Bearing Using Genetic Algorithm

    Directory of Open Access Journals (Sweden)

    Lintu Roy

    2013-01-01

    Full Text Available This paper presents the various arrangements of grooving location of two-groove oil journal bearing for optimum performance. An attempt has been made to find out the effect of different configurations of two groove oil journal bearing by changing groove locations. Various groove angles that have been considered are 10°, 20°, and 30°. The Reynolds equation is solved numerically in a finite difference grid satisfying the appropriate boundary conditions. Determination of optimum performance is based on maximization of nondimensional load, flow coefficient, and mass parameter and minimization of friction variable using genetic algorithm. The results using genetic algorithm are compared with sequential quadratic programming (SQP. The two grooved bearings in general have grooves placed at diametrically opposite directions. However, the optimum groove locations, arrived at in the present work, are not diametrically opposite.

  4. Investigation of a Tricarbide Grooved Ring Fuel Element for a Nuclear Thermal Rocket

    Science.gov (United States)

    Taylor, Brian D.; Emrich, Bill; Tucker, Dennis; Barnes, Marvin; Donders, Nicolas; Benensky, Kelsa

    2017-01-01

    Deep space exploration, especially that of Mars, is on the horizon as the next big challenge for space exploration. Nuclear propulsion, through which high thrust and efficiency can be achieved, is a promising option for decreasing the cost and logistics of such a mission. Work on nuclear thermal engines goes back to the days of the NERVA program. Currently, nuclear thermal propulsion is under development again in various forms to provide a superior propulsion system for deep space exploration. The authors have been working to develop a concept nuclear thermal engine that uses a grooved ring fuel element as an alternative to the traditional hexagonal rod design. The authors are also studying the use of carbide fuels. The concept was developed in order to increase surface area and heat transfer to the propellant. The use of carbides would also raise the temperature limitations of the reactor. It is hoped that this could lead to a higher thrust to weight nuclear thermal engine. This paper describes the modeling of neutronics, heat transfer, and fluid dynamics of this alternative nuclear fuel element geometry. Fabrication experiments of grooved rings from carbide refractory metals are also presented along with material characterization and interactions with a hot hydrogen environment.

  5. Performance studies of oil lubricated helical groove journal bearing

    OpenAIRE

    Khan, Muhammad Zubair

    1992-01-01

    This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University. The provision of helical grooves on the surface of a plain journal bearing can improve the stability of a rotor-bearing system. However, the improvement depends on the arrangement of the grooves along the axial length of the bearing. In order to verify this improved stability three types of helical groove bearing and a reference plain journal bearing were investigated. The helical groove jour...

  6. Study of a Tricarbide Grooved Ring Fuel Element for Nuclear Thermal Propulsion

    Science.gov (United States)

    Taylor, Brian; Emrich, Bill; Tucker, Dennis; Barnes, Marvin; Donders, Nicolas; Benensky, Kelsa

    2018-01-01

    Deep space exploration, especially that of Mars, is on the horizon as the next big challenge for space exploration. Nuclear propulsion, through which high thrust and efficiency can be achieved, is a promising option for decreasing the cost and logistics of such a mission. Work on nuclear thermal engines goes back to the days of the NERVA program. Currently, nuclear thermal propulsion is under development again in various forms to provide a superior propulsion system for deep space exploration. The authors have been working to develop a concept nuclear thermal engine that uses a grooved ring fuel element as an alternative to the traditional hexagonal rod design. The authors are also studying the use of carbide fuels. The concept was developed in order to increase surface area and heat transfer to the propellant. The use of carbides would also raise the operating temperature of the reactor. It is hoped that this could lead to a higher thrust to weight nuclear thermal engine. This paper describes the modeling of neutronics, heat transfer, and fluid dynamics of this alternative nuclear fuel element geometry. Fabrication experiments of grooved rings from carbide refractory metals are also presented along with material characterization and interactions with a hot hydrogen environment. Results of experiments and associated analysis are discussed. The authors demonstrated success in reaching desired densities with some success in material distribution and reaching a solid solution. Future work is needed to improve distribution of material, minimize oxidation during the milling process, and define a fabrication process that will serve for constructing grooved ring fuel rods for large system tests.

  7. Shaping low-thrust trajectories with thrust-handling feature

    Science.gov (United States)

    Taheri, Ehsan; Kolmanovsky, Ilya; Atkins, Ella

    2018-02-01

    Shape-based methods are becoming popular in low-thrust trajectory optimization due to their fast computation speeds. In existing shape-based methods constraints are treated at the acceleration level but not at the thrust level. These two constraint types are not equivalent since spacecraft mass decreases over time as fuel is expended. This paper develops a shape-based method based on a Fourier series approximation that is capable of representing trajectories defined in spherical coordinates and that enforces thrust constraints. An objective function can be incorporated to minimize overall mission cost, i.e., achieve minimum ΔV . A representative mission from Earth to Mars is studied. The proposed Fourier series technique is demonstrated capable of generating feasible and near-optimal trajectories. These attributes can facilitate future low-thrust mission designs where different trajectory alternatives must be rapidly constructed and evaluated.

  8. The perfect shape spiral stories

    CERN Document Server

    Hammer, Øyvind

    2016-01-01

    This book uses the spiral shape as a key to a multitude of strange and seemingly disparate stories about art, nature, science, mathematics, and the human endeavour. In a way, the book is itself organized as a spiral, with almost disconnected chapters circling around and closing in on the common theme. A particular strength of the book is its extremely cross-disciplinary nature - everything is fun, and everything is connected! At the same time, the author puts great emphasis on mathematical and scientific correctness, in contrast, perhaps, with some earlier books on spirals. Subjects include the mathematical properties of spirals, sea shells, sun flowers, Greek architecture, air ships, the history of mathematics, spiral galaxies, the anatomy of the human hand, the art of prehistoric Europe, Alfred Hitchcock, and spider webs, to name a few.

  9. Optics of a single ultrasharp groove in metal

    DEFF Research Database (Denmark)

    Søndergaard, Thomas; Bozhevolnyi, Sergey I

    2016-01-01

    Optical properties of a single ultrasharp groove of subwavelength width cut in an otherwise flat metal surface are examined theoretically. We calculate optical extinction, scattering, and absorption cross-section spectra for a wide range of groove profiles, establishing several fundamental trends...... absorption spectra. For ultrasharp grooves, oscillations in all spectra can be suppressed by increasing the groove depth. Finally, the level of absorption relative to that of scattering increases as the top groove width decreases, a trend that is analogous to that found when decreasing the size of metal...

  10. Analysis of oil lubricated, fluid film, thrust bearings with allowance for temperature dependent viscosity

    Science.gov (United States)

    Pan, C. H. T.; Malanoski, S. B.

    1972-01-01

    A preliminary design study was performed to seek a fluid-film thrust bearing design intended to be part of a high-speed, hybrid (rolling element/fluid film) bearing configuration. The base line used is a design previously tested. To improve the accuracy of theoretical predictions of load capacity, flow rate, and friction power loss, an analytical procedure was developed to include curvature effects inherent in thrust bearings and to allow for the temperature rise in the fluid due to viscous heating. Also, a narrow-groove approximation in the treatment of the temperature field was formulated to apply the procedure to the Whipple thrust bearing. A comparative trade-off study was carried out assuming isothermal films; its results showed the shrouded-step design to be superior to the Whipple design for the intended application. An extensive parametric study was performed, employing isoviscous calculations, to determine the optimized design, which was subsequently recalculated allowing for temperature effects.

  11. Aircraft Horizontal Thrust Measurement Facility

    Data.gov (United States)

    Federal Laboratory Consortium — This facility is designed to support the DoD mission by providing unique air vehicle installed engine performance (thrust output) measurements. This system consists...

  12. Labiogingival groove: A rare developmental tooth anomaly

    Directory of Open Access Journals (Sweden)

    Shiva Chauhan

    2017-01-01

    Full Text Available Labiogingival groove is a congenital morphologic dental anomaly, in which an infolding of the inner enamel epithelium and Hertwig's epithelial root sheath create a groove extending varying depth into root. Epithelial attachment can be breached by gingival irritation secondary to plaque accumulation creating a periodontal defect that spreads to the pulp causing primary periodontal/secondary endodontic. A 12-year-old boy reported with the complaint of painful tooth with pus discharge from labial gingival surface in the maxillary right lateral incisor for 4 months. Intraoral examination revealed bluish red gingiva with loss of contour in relation to maxillary right lateral incisor and purulent discharge in relation to it. A provisional diagnosis of localized gingival abscess in relation to maxillary right incisor (primary periodontic and secondary endodontic involvement was given, and required treatment was carried out. On exposure of the involved tooth, a labiogingival groove was noticed which could have been a contributing factor for the progression of the condition.

  13. Hurricane Spiral Bands.

    Science.gov (United States)

    Guinn, Thomas A.; Schubert, Wayne H.

    1993-10-01

    The spiral bands that occur in tropical cyclones can be conveniently divided into two classes-outer bands and inner bands. Evidence is presented here that the outer bands form as the result of nonlinear effects during the breakdown of the intertropical convergence zone (ITCZ) through barotropic instability. In this process a zonal strip of high potential vorticity (the ITCZ shear zone or monsoon trough) begins to distort in a varicose fashion, with the potential vorticity (PV) becoming pooled in local regions that are connected by filaments of high PV. As the pooled regions become more axisymmetric, the filaments become thinner and begin to wrap around the PV centers.It is argued that inner bands form in a different manner. As a tropical cyclone intensifies due to latent heat release, the PV field becomes nearly circular with the highest values of PV in the cyclone center. The radial gradient of PV provides a state on which PV waves (the generalization of Rossby waves) can propagate. The nonlinear breaking of PV waves then leads to an irreversible distortion of the PV contours and a downgradient flux of PV. The continuation of this proem tends to erode the high PV core of the tropical cyclone, to produce a surrounding surf zone, and hence to spread the PV horizontally. In a similar fashion, inner bands can also form by the merger of a vortex with a patch of relatively high PV air. As the merger proem occurs the patch of PV is quickly elongated and wrapped around the vortex. The resulting vortex is generally larger in horizontal extent and exhibits a spiral band of PV.When the formation of outer and inner bands is interpreted in the context of a normal-mode spectral model, they emerge as slow manifold phenomena; that is, they have both rotational and (balanced or slaved) gravitational mode aspects. In this sense, regarding them as simply gravity waves leads to an incomplete dynamical picture.

  14. Measuring with the spiral reader

    CERN Multimedia

    1974-01-01

    The spiral reader shown here was at the time, together with the Shivamatic scanning system, the basic equipment used for measuring bubble chamber pictures. Anne Anton sits at the table. (See Photo Archive 7408343.)

  15. Spiral-shaped disinfection reactors

    KAUST Repository

    Ghaffour, Noreddine

    2015-08-20

    This disclosure includes disinfection reactors and processes for the disinfection of water. Some disinfection reactors include a body that defines an inlet, an outlet, and a spiral flow path between the inlet and the outlet, in which the body is configured to receive water and a disinfectant at the inlet such that the water is exposed to the disinfectant as the water flows through the spiral flow path. Also disclosed are processes for disinfecting water in such disinfection reactors.

  16. Spiral inlets for steam turbines

    Science.gov (United States)

    Škach, Radek; Uher, Jan

    2017-09-01

    This paper deals with the design process of special nozzle blades for spiral inlets. Spiral inlets are used for the first stages of high pressure and intermediate pressure steam turbines with both reaction and impulse blades when throttling or sliding pressure control is applied. They improve the steam flow uniformity from the inlet pipe and thus decrease the aerodynamic losses. The proposed evaluation of the inlet angle is based on the free vortex law.

  17. [Microsurgical removal of olfactory groove meningiomas].

    Science.gov (United States)

    Liang, Ri-Sheng; Zhou, Liang-Fu; Mao, Ying; Zhang, Rong; Yang, Wei-Zhong

    2011-01-01

    To explore an effective method for further improving the surgical results of treatment of olfactory groove meningiomas. Sixty seven cases of olfactory groove meningiomas were treated by microneurosurgery, among which fifty seven were de novo cases, eight were recurrent tumors and the other two re-recurrent cases. Modified Derome approach was used in 12 cases, bilateral subfrontal approach in 28 cases, modified pterional approach in 21 cases and unilateral subfrontal approach in six cases. Tumors were resected microsurgically with radical removal of invaded dura, bone, and paranasal sinus mucosa. Reconstruction was performed in patients with skull base defect. Simpson grade I removal was accomplished in 59 cases, grade II in seven cases and grade IV in one case. Among 57 patients with de novo tumor, Simpson I resection was accomplished in 54 cases. Postoperative rhinorrhea and intracranial infection occurred in one case and was cured after temporal lumbar CSF drainage and antibiotic therapy. Two patients (2.9%) died within one month after operation, i.e.one aged patient of heart failure and the other of severe hypothalamus complication. Forty seven patients (72.3%) were followed up from one to ten years with an average of five years and four months. With the exception of two cases died, among the alive 45 patients, there were only three patients with tumor recurrence, which had undergone Simpson II or IV tumor resection. No recurrence was found in cases with Simpson I tumor removal. Previous blurred vision was not improved in three patients, hemiparalysis in two patients, and the other patients recovered well, resuming previous jobs or being able to take care themselves. Total tumor removal (Simpson I) should be the surgical goal for treatment of olfactory groove meningiomas, especially for de novo cases. An appropriate approach is fundamental in the effort to remove an OGM totally. Appropriate anterior skull base reconstruction with vascularized material is

  18. Laser Surface Hardening of Groove Edges

    Science.gov (United States)

    Hussain, A.; Hamdani, A. H.; Akhter, R.; Aslam, M.

    2013-06-01

    Surface hardening of groove-edges made of 3Cr13 Stainless Steel has been carried out using 500 W CO2 laser with a rectangular beam of 2.5×3 mm2. The processing speed was varied from 150-500 mm/min. It was seen that the hardened depth increases with increase in laser interaction time. A maximum hardened depth of around 1mm was achieved. The microhardness of the transformed zone was 2.5 times the hardness of base metal. The XRD's and microstructural analysis were also reported.

  19. Syncopation, body-movement and pleasure in groove music.

    OpenAIRE

    Witek, MA; Clarke, EF; Wallentin, M; Kringelbach, ML; Vuust, P

    2014-01-01

    Moving to music is an essential human pleasure particularly related to musical groove. Structurally, music associated with groove is often characterised by rhythmic complexity in the form of syncopation, frequently observed in musical styles such as funk, hip-hop and electronic dance music. Structural complexity has been related to positive affect in music more broadly, but the function of syncopation in eliciting pleasure and body-movement in groove is unknown. Here we report results from a ...

  20. Thrust Deduction in Contrarotating Propellers

    Science.gov (United States)

    1974-11-01

    reduced by unbalancing the propelling thrust with smaller thrust carried on the forward propeller. UNCLASSIFIED SECURITY CLASIFICATION OF THIS...Webb lnst/Waird 1 154 W. Morgan 1 WHOI Ocean Engr 1 1644 R. Cumming 1 WPI Alden Hydr Lab 1 1552 J. McCarthy 1 SNAME 1 156 J. Hadler 1 Bethlehem Steel ...New York 30 5614 Report Distribution 1 Bethlehem Steel Sparrows 1 5641I Library 1 Bolt Beranek and Newman 1 5642 Library, Annapolis 1 Eastern Res Group 32

  1. Dual-phase CT findings of groove pancreatitis

    Energy Technology Data Exchange (ETDEWEB)

    Zaheer, Atif, E-mail: azaheer1@jhmi.edu [The Russell H. Morgan Department of Radiology and Radiological Science, Johns Hopkins Medical Institutions, Baltimore, MD 21231 (United States); Pancreatitis Center, Division of Gastroenterology, Department of Medicine, Johns Hopkins Medical Institutions, Baltimore, MD 21231 (United States); Haider, Maera, E-mail: mhaider3@jhmi.edu [The Russell H. Morgan Department of Radiology and Radiological Science, Johns Hopkins Medical Institutions, Baltimore, MD 21231 (United States); Kawamoto, Satomi, E-mail: skawamo1@jhmi.edu [The Russell H. Morgan Department of Radiology and Radiological Science, Johns Hopkins Medical Institutions, Baltimore, MD 21231 (United States); Hruban, Ralph H., E-mail: rhruban1@jhmi.edu [Department of Pathology, The Sol Goldman Pancreatic Cancer Research Center, the Johns Hopkins University School of Medicine, Baltimore, MD 21231 (United States); Fishman, Elliot K., E-mail: efishma1@jhmi.edu [The Russell H. Morgan Department of Radiology and Radiological Science, Johns Hopkins Medical Institutions, Baltimore, MD 21231 (United States)

    2014-08-15

    Purpose: Groove pancreatitis is a rare focal form of chronic pancreatitis that occurs in the pancreaticoduodenal groove between the major and minor papillae, duodenum and pancreatic head. Radiologic appearance and clinical presentation can result in suspicion of malignancy rendering pancreaticoduodenectomy inevitable. This study reports dual phase CT findings in a series of 12 patients with pathology proven groove pancreatitis. Materials and methods: Retrospective review of preoperative CT findings in 12 patients with histologically proven groove pancreatitis after pancreaticoduodenectomy. Size, location, attenuation, presence of mass or cystic components in the pancreas, groove and duodenum, calcifications, duodenal stenosis and ductal changes were recorded. Clinical data, laboratory values, endoscopic ultrasonographic and histopathological findings were collected. Results: Soft tissue thickening in the groove was seen in all patients. Pancreatic head, groove and duodenum were all involved in 75% patients. A discrete lesion in the pancreatic head was seen in half of the patients, most of which appeared hypodense on both arterial and venous phases. Cystic changes in pancreatic head were seen in 75% patients. Duodenal involvement was seen in 92% patients including wall thickening and cyst formation. The main pancreatic duct was dilated in 7 patients, with an abrupt cut off in 3 and a smooth tapering stricture in 4. Five patients had evidence of chronic pancreatitis with parenchymal calcifications. Conclusion: Presence of mass or soft tissue thickening in the groove with cystic duodenal thickening is highly suggestive of groove pancreatitis. Recognizing common radiological features may help in diagnosis and reduce suspicion of malignancy.

  2. Sensorimotor coupling in music and the psychology of the groove.

    Science.gov (United States)

    Janata, Petr; Tomic, Stefan T; Haberman, Jason M

    2012-02-01

    The urge to move in response to music, combined with the positive affect associated with the coupling of sensory and motor processes while engaging with music (referred to as sensorimotor coupling) in a seemingly effortless way, is commonly described as the feeling of being in the groove. Here, we systematically explore this compelling phenomenon in a population of young adults. We utilize multiple levels of analysis, comprising phenomenological, behavioral, and computational techniques. Specifically, we show (a) that the concept of the groove is widely appreciated and understood in terms of a pleasurable drive toward action, (b) that a broad range of musical excerpts can be appraised reliably for the degree of perceived groove, (c) that the degree of experienced groove is inversely related to experienced difficulty of bimanual sensorimotor coupling under tapping regimes with varying levels of expressive constraint, (d) that high-groove stimuli elicit spontaneous rhythmic movements, and (e) that quantifiable measures of the quality of sensorimotor coupling predict the degree of experienced groove. Our results complement traditional discourse regarding the groove, which has tended to take the psychological phenomenon for granted and has focused instead on the musical and especially the rhythmic qualities of particular genres of music that lead to the perception of groove. We conclude that groove can be treated as a psychological construct and model system that allows for experimental exploration of the relationship between sensorimotor coupling with music and emotion.

  3. Experimental equipment for measuring physical properties of the annular hydrostatic thrust bearing

    Directory of Open Access Journals (Sweden)

    Kozdera Michal

    2014-03-01

    Full Text Available The hydraulic circuit, through which the mineral oil is brought, is an important part of hydrostatic bearings. The annular hydrostatic thrust bearing consists of two sliding plates divided by a layer of mineral oil. In the lower plate, there are oil grooves which distribute the liquid between the sliding areas. The hydraulic circuit is made of two basic parts: the energy source and the controlling part. The hydraulic pump, which brings the liquid into the sliding bearing, is the source of the pressure energy. The sliding bearing is weighted down by axial force, which can be changed during the process. That´s why in front of the particular oil grooves control components adjusting pressure and flow size are located. This paper deals with a project of a hydraulic circuit for regulation of fluid layer in the annular hydrostatic thrust bearing and the testing equipment for measuring its physical properties. It will include the issue of measuring loading capacity and height of the fluid layer in the annular hydrostatic thrust bearing.

  4. Effect of Rake Angle During Machining of Micro Grooves on Electroless Nickel Plated Die Materials

    International Nuclear Information System (INIS)

    Rezaur Rahman, K.M.; Rahman, M.

    2005-01-01

    This study attempts to evaluate the performance of two single crystal diamond tools with different rake angle (0 0 and -15 0 ) during micro grooving on electroless nickel plated die materials. It was found that the 0 0 rake diamond tool has superior performance compared to the -15 0 rake angle tool. The negative rake tool experienced very high thrust force, and severe chipping on the flank face was evident after a short cutting distance of 3.13 km. On the other hand, the 0 0 rake tool machined satisfactorily up to 50 km without any significant tool wear. While machining with the -15 0 rake tool, significant change in surface roughness with spindle speed was observed compared to the 0 0 rake tool. With increasing infeed rate variation in surface roughness was evident only with the -15 0 rake tool. Steep change in roughness with machining distance was also observed while machining with the negative rake tool. (authors)

  5. Another Look at Rocket Thrust

    Science.gov (United States)

    Hester, Brooke; Burris, Jennifer

    2012-01-01

    Rocket propulsion is often introduced as an example of Newton's third law. The rocket exerts a force on the exhaust gas being ejected; the gas exerts an equal and opposite force--the thrust--on the rocket. Equivalently, in the absence of a net external force, the total momentum of the system, rocket plus ejected gas, remains constant. The law of…

  6. Spiral Inflector For Compact Cyclotron

    CERN Document Server

    Karamysheva, G A

    2004-01-01

    Compact cyclotron for explosives detection by nuclear resonance absorption of γ-rays in nitrogen is under development [1] Cyclotron will be equipped with the external ion source. The injection system consists of a double-drift beam bunching system, a spiral inflector, beam diagnostics, focusing and adjustment elements [2]. The spiral inflector for ion bending from axial to median plane is used. Computer model of spiral inflector for the Customs cyclotron is developed. 3D electrostatic field calculations of the designed inflector are performed. Calculated electric field map and magnetic field map of the cyclotron [3] are used for beam dynamic simulations. Numeric simulations are carried out for 500 particles using code for calculation of particle dynamics by integration of differential equations in Cartesian coordinate system written in MATLAB. Direct Coulomb particle-to-particle method is used to take into account space-charge effects.

  7. Dynamics of gas-thrust bearings

    Science.gov (United States)

    Stiffler, A. K.; Tapia, R. R.

    1978-01-01

    Computer program calculates load coefficients, up to third harmonic, for hydrostatic gas thrust bearings. Program is useful in identification of industrial situations where gas-thrust bearings have potential applications.

  8. High Thrust-Density Electrostaic Engines Project

    Data.gov (United States)

    National Aeronautics and Space Administration — These issues are addressable by: increasing the thrust, power, and thrust-to-power ratio capability of EP systems; reducing the non-recurring engineering systems...

  9. Olfactory groove meningiomas: approaches and complications.

    Science.gov (United States)

    Aguiar, Paulo Henrique Pires de; Tahara, Adriana; Almeida, Antonio Nogueira; Simm, Renata; Silva, Arnaldo Neves da; Maldaun, Marcos Vinicius Calfatt; Panagopoulos, Alexandros Theodoros; Zicarelli, Carlos Alexandre; Silva, Pedro Gabriel

    2009-09-01

    Olfactory groove meningiomas (OGM) account for 4.5% of all intracranial meningiomas. We report 21 patients with OGMs. Tumors were operated on using three surgical approaches: bifrontal (7 patients), fronto-pterional (11 patients) and fronto-orbital (3 patients). Total tumor removal (Simpson Grade 1) was achieved in 13 patients and Simpson II in 8 patients. Perioperative mortality was 4.76%. The average size of the OGM was 4.3+/-1.1cm. The overall recurrence rate was 19%. We preferred to use the pterional approach, which provides quick access to the tumor with less brain exposure. It also allows complete drainage of cisternal cerebrospinal fluid, providing a good level of brain relaxation during surgery. However, for long, thin tumors, hemostasis can be difficult using this approach.

  10. Fabrication of advanced design (grooved) cermet anodes

    Energy Technology Data Exchange (ETDEWEB)

    Windisch, C.F. Jr. [Pacific Northwest Lab., Richland, WA (United States); Huettig, F.R. [Ceramic Magnetics, Inc., Fairfield, NJ (United States)

    1993-05-01

    Attempts were made to fabricate full-size anodes with advanced, or grooved, design using isostatic pressing, slip casting injection molding. Of the three approaches, isostatic pressing produced an anode with dimensions nearest to the target specifications, without serious macroscopic flaws. This approach is considered the most promising for making advanced anodes for aluminum smelting. However, significant work still remains to optimize the physical properties and microstructure of the anode, both of which were significantly different from that of previous anodes. Injection molding and slip casting yielded anode materials with serious deficiencies, including cracks and holes. Injection molding gave cermet material with the best intrinsic microstructure, i.e., the microstructure of the material between macroscopic flaws was very similar to that of anodes previously made at PNL. Reason for the similarity may have to do with amount of residual binder in the material prior to sintering.

  11. Effects of ultrasonic vibrations in micro-groove turning.

    Science.gov (United States)

    Zhang, Chen; Guo, Ping; Ehmann, Kornel F; Li, Yingguang

    2016-04-01

    Ultrasonic vibration cutting is an efficient cutting process for mechanical micro-machining. This process can generate intricate surface textures with different geometric characteristics. Micro-grooves/micro-channels are among the most frequently encountered micro-structures and, as such, are the focus of this paper. The effectiveness of both the linear and ultrasonic elliptical vibration-assisted machining technique in micro-groove turning is analyzed and discussed in the paper. The paper first investigates the mechanisms of micro-groove generation induced by the linear and elliptical vibration modes. A simplified cutting force analysis method is given to compare the effectiveness of the two modes in micro-groove turning. The surface roughness of the generated micro-grooves is analyzed next and theoretical expressions are given for the two cases. Finally, micro-groove turning experiments are conducted to compare the influences of the two vibration modes on the cutting forces and the surface roughness. The experimental results show that linear vibration-assisted micro-groove turning leads to better surface roughness as compared to the elliptical vibration-assisted case, while elliptical vibration-assisted micro-groove turning shows advantages in terms of decreasing the cutting forces. Copyright © 2016 Elsevier B.V. All rights reserved.

  12. Heat transfer and thermal stress analysis in grooved tubes

    Indian Academy of Sciences (India)

    grooved tubes and three different mean inlet water velocities. Constant temperature was applied from the external surface of the tube. Energy and governing flow equations were solved using finite difference scheme. Finite element method (FEM) was used to compute the thermal stress fields. Grooving effects on the thermal ...

  13. Heat transfer and thermal stress analysis in grooved tubes

    Indian Academy of Sciences (India)

    The maximum thermal stress ratio positions inside the tube have been indicated as MX for all investigated cases. In the light of the thermal stress values, various designs can be applied to reduce thermal stress in grooved tubes. Keywords. Heat transfer; thermal stress; grooved tubes. 1. Introduction. Heat transfer in pipe flow ...

  14. Heat transfer and thermal stress analysis in grooved tubes

    Indian Academy of Sciences (India)

    Heat transfer and thermal stresses, induced by temperature differencesin the internally grooved tubes of heat transfer equipment, have been analysed numerically. The analysis has been conducted for four different kinds of internally grooved tubes and three different mean inlet water velocities. Constant temperature was ...

  15. A GROOVE Solution for the BPMN to BPEL Model Transformation

    NARCIS (Netherlands)

    de Mol, M.J.; Zimakova, M.V.

    In this paper we present a solution of a model transformation between two standard languages for business process modeling BPMN and BPEL, using the GROOVE tool set. GROOVE is a tool for graph transformations that uses directed, edge labelled simple graphs and the SPO approach [Ren04]. Given a graph

  16. Crystallization of Poly(3-hexylthiophene Nanofiber in a Narrow Groove

    Directory of Open Access Journals (Sweden)

    Satoshi Kushi

    2016-06-01

    Full Text Available Whisker-type poly(3-hexylthiophene-2,5-diyl (P3HT nanofibers were aligned by restricting their growth direction using an approximately 100–1000 nm wide narrow groove fabricated by thermal nanoimprinting. In grooves made of an amorphous fluoropolymer (CYTOP™ with widths of less than 1500 nm, the nanofibers oriented uniaxially perpendicular to the groove and their length was limited to the width of the groove. This result indicates that the nucleation of nanofibers tends to be selectively promoted near the interface of CYTOP™ with fluoro-groups, and nanofiber growth perpendicular to the wall is promoted because P3HT molecules are supplied more frequently from the center of the groove. Furthermore, the orientation induced anisotropic conductivity, and the conductivity parallel to the oriented nanofibers was more than an order of magnitude higher than that perpendicular to the oriented nanofibers.

  17. Nonlinear dynamics of a vectored thrust aircraft

    DEFF Research Database (Denmark)

    Sørensen, C.B; Mosekilde, Erik

    1996-01-01

    With realistic relations for the aerodynamic coefficients, numerical simulations are applied to study the longitudional dynamics of a thrust vectored aircraft. As function of the thrust magnitude and the thrust vectoring angle the equilibrium state exhibits two saddle-node bifurcations and three...

  18. GANIL-SPIRAL1-SPIRAL2: Highlights and Perspectives

    Science.gov (United States)

    Gales, S.

    2010-06-01

    GANIL presently offers unique opportunities in nuclear physics and many other fields that arise from not only the provision of low-energy stable beams, fragmentation beams and re-accelerated radioactive species, but also from the availability of a wide range of state-of-the-art spectrometers and instrumentation. A few examples of recent highlights are presented. With the construction of SPIRAL2 over the next few years, GANIL is in a good position to retain its world-leading capability. As selected by the ESFRI committee, the next generation of ISOL facility in Europe is represented by the SPIRAL2 project to be built at GANIL (Caen, France). SPIRAL 2 is based on a high power, CW, superconducting LINAC, delivering 5 mA of deuteron beams at 40 MeV (200 KW) directed on a C converter+ Uranium target and producing therefore more 1013 fissions/s. The expected radioactive beams intensities in the mass range from A = 60 to A = 140, will surpass by two order of magnitude any existing facilities in the world. These unstable atoms will be available at energies between few KeV/n to 15 MeV/n. The same driver will accelerate high intensity (100*A to 1 mA), heavier ions (Ar up to Xe) at maximum energy of 14 MeV/n. Under the 7FP program of European Union called*Preparatory phase*, the SPIRAL2 project has been granted a budget of about 4 M€ to build up an international consortium around this new venture. The status of the construction of SPIRAL2 accelerator and associated physics instruments in collaboration with EU and International partners will be presented.

  19. Quasicrystallography on the spiral of Archimedes

    International Nuclear Information System (INIS)

    Bursill, L.A.

    1990-01-01

    The concept of a spiral lattice is discussed. Some examples of known mineral structures, namely clino asbestos, halloysite and cylindrite, are then interpreted in terms of this structural principle. An example of a synthetic sulphide catalyst spiral structure having atomic dimensions is also described. All of these inorganic spiral structures are based on the sprial of Archimedes. The principles for a new type of crystallography, based on the Archimedian spiral, are then presented. 45 refs., 8 figs

  20. Establishing design criteria for crankshaft thrust bearings in gasoline and diesel engines by computer simulations and experiments. Crankshaft thrust bearing design - final report; Auslegungskriterien fuer Kurbelwellenaxiallager in Otto- und Dieselmotoren durch rechnergestuetzte Simulation und experimentelle Untersuchungen. Axialgleitlagerauslegung - Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Hunsicker, W. [Fachhochschule Mannheim (Germany). Inst. fuer Tribologie; Backhaus, K. [Univ. GH Kassel (Germany). Inst. fuer Maschinenelemente und Konstruktionstechnik; Schubert, W. [KS Gleitlager GmbH, Papenburg (Germany)

    2004-07-01

    Aim of the research-project was it to increase the calculation safety of crank shaft thrust bearings in combustion engines. The project was divided in two parts: (1) A simulation program to analyze the load bearing capacity of axial bearings under mixed lubrication has been developed at the Institut fuer Maschinenelemente und Konstruktionstechnik, University of Kassel. This part of the research-project has been presented at the FVV Herbsttagung in 2003. (2) The test runs with original parts were carried out on a newly designed thrust bearing test rig at the Institut fuer Tribologie, University of Applied Sciences in Mannheim. The following presentation shows the results of part 2. The experimental results show the influence of rotational frequency, load, bearing material, lateral run-out of the tread of the crankshaft and groove pattern. These test runs will help to dimension thrust bearings more efficiently. (orig.)

  1. Recommended Practices in Thrust Measurements

    Science.gov (United States)

    2013-10-01

    measurement from mi- crothrusters,” Rev. Sci. Inst., Vol. 75, No. 10, 2004, pp. 3185–3190. 3McFall, K. and Tilley, D., “ Low Power Arcjet Performance...and Performance Summary,” 44th Joint Propulsion Conference, Hartford, CT, 2008, AIAA-2008-4824. 7Manzella, D. et al., “Evaluation of low power Hall...thrusters produce relatively low thrust levels, particularly microthrusters that have enjoyed increased attention in the last two decades, direct

  2. Simplified installation of thrust bearings

    Science.gov (United States)

    Sensenbaugh, N. D.

    1980-01-01

    Special handling sleeve, key to method of installing thrust bearings, was developed for assembling bearings on shaft of low-pressure oxygen turbo-pump. Method eliminates cooling and vacuum-drying steps which saves time, while also eliminating possibility of corrosion formation. Procedure saves energy because it requires no liquid nitrogen for cooling shaft and no natural gas or electric power for operating vacuum oven.

  3. Inspired Spirals. Teaching Art with Art.

    Science.gov (United States)

    Hubbard, Guy

    2001-01-01

    Discusses spirals in nature, man-made objects, and art. Focuses on art that incorporates the spiral, including works by M. C. Escher and Frank Lloyd Wright, an African headdress, and a burial urn. Describes activities to help students make spirals of their own, such as constructing a coil clay pot. (CMK)

  4. The Spiral Pattern During Development*

    African Journals Online (AJOL)

    1971-08-07

    Aug 7, 1971 ... which are destined to become the limb areas bud out laterally. Fig. 8. The early cells, which are destined to develop into the upper and the lower limbs, after lateral budding has occurred. Fig. 11 demonstrates the human embryo of about 5 mm. CR length and age of about 32 days. The spiral pattern is.

  5. A study of spiral galaxies

    International Nuclear Information System (INIS)

    Wevers, B.M.H.R.

    1984-01-01

    Attempts have been made to look for possible correlations between integral properties of spiral galaxies as a function of morphological type. To investigate this problem, one needs the detailed distribution of both the gaseous and the stellar components for a well-defined sample of spiral galaxies. A sample of about 20 spiral galaxies was therefore defined; these galaxies were observed in the 21 cm neutral hydrogen line with the Westerbork Synthesis Radio Telescope and in three broad-band optical colours with the 48-inch Palomar Smidt Telescope. First, an atlas of the combined radio and optical observations of 16 nearby northern-hemisphere spiral galaxies is presented. Luminosity profiles are discussed and the scale lengths of the exponential disks and extrapolated central surface brightnesses are derived, as well as radial color distributions; azimuthal surface brightness distributions and rotation curves. Possible correlations with optical features are investigated. It is found that 20 to 50 per cent of the total mass is in the disk. (Auth.)

  6. Optimization of self-acting step thrust bearings for load capacity and stiffness.

    Science.gov (United States)

    Hamrock, B. J.

    1972-01-01

    Linearized analysis of a finite-width rectangular step thrust bearing. Dimensionless load capacity and stiffness are expressed in terms of a Fourier cosine series. The dimensionless load capacity and stiffness were found to be a function of the dimensionless bearing number, the pad length-to-width ratio, the film thickness ratio, the step location parameter, and the feed groove parameter. The equations obtained in the analysis were verified. The assumptions imposed were substantiated by comparing the results with an existing exact solution for the infinite width bearing. A digital computer program was developed which determines optimal bearing configuration for maximum load capacity or stiffness. Simple design curves are presented. Results are shown for both compressible and incompressible lubrication. Through a parameter transformation the results are directly usable in designing optimal step sector thrust bearings.

  7. Thrust sensing for small UAVs

    Science.gov (United States)

    Marchman, Christopher Scott

    Unmanned aerial vehicles (UAVs) have become prevalent in both military and civilian applications. UAVs have many size categories from large-scale aircraft to micro air vehicles. The performance, health, and efficiency for UAVs of smaller sizes can be difficult to assess and few associated instrumentation systems have been developed. Thrust measurements on the ground can characterize systems especially when combined with simultaneous motor power measurements. This thesis demonstrates the use of strain measurements to measure the thrust produced by motor/propeller combinations for such small UAVs. A full-bridge Wheatstone circuit and electrical resistance strain gauges were used in conjunction with constant-stress cantilever beams for static tests and dynamic wind tunnel tests. An associated instrumentation module monitored power from the electric motor. Monitoring the thrust data over time can provide insights into optimal propeller and motor selection and early detection of problems such as component failure. The approach provides a system for laboratory or field measurements that can be scaled for a wide range of small UAVs.

  8. Numerical study on condensation heat transfer of trapezoid grooved surfaces

    Directory of Open Access Journals (Sweden)

    Baojin Qi

    2016-05-01

    Full Text Available This article presents a numerical analysis and experimental study on condensation heat transfer and fluid flow for filmwise condensation on trapezoid grooved surfaces. First, a physical model was properly simplified based on some reasonable assumptions. Then, the coupled non-linear governing equations for the mass transfer, fluid flow, and two-dimensional thermal conduction were developed. The relationship between z-coordinate and heat transfer was obtained by solving the equations numerically. The influences of groove length and basic angle were discussed. The calculation results showed that the heat flux decreased with increase in groove length, and the decline range also decreased gradually. The calculation results also suggested that the heat flux through groove with α = 60° was lower than the groove with α = 75° at the top of the groove, while the opposite conclusion was obtained at the low parts. The distributions of wall temperature and heat flux on trapezoid groove were also studied systematically. The distribution of surface temperature and heat flux presents obvious lateral inhomogeneity, and the maximum wall temperature and heat flux were both obtained in region II. The thermal resistance of groove with α = 60° was lower but the liquid-discharged ability was better than that of groove with α = 75°. In order to validate the feasibility and reliability of the present analyses and to further investigate the heat transfer performance of trapezoid grooved surfaces, experiments were carried out with three condensing plates including two trapezoid grooved surfaces in different physical dimensions and one smooth surface. The experimental data obtained under various schooling were compared with the calculations, and the experimental results for different condensing plates are all in good agreement with the numerical model, with a maximum deviation less than 15%. Moreover, the trapezoid grooves can enhance the

  9. Gap and channeled plasmons in tapered grooves: a review

    DEFF Research Database (Denmark)

    Smith, C. L. C.; Stenger, Nicolas; Kristensen, Anders

    2015-01-01

    Tapered metallic grooves have been shown to support plasmons - electromagnetically coupled oscillations of free electrons at metal-dielectric interfaces - across a variety of configurations and V-like profiles. Such plasmons may be divided into two categories: gap-surface plasmons (GSPs) that are......Tapered metallic grooves have been shown to support plasmons - electromagnetically coupled oscillations of free electrons at metal-dielectric interfaces - across a variety of configurations and V-like profiles. Such plasmons may be divided into two categories: gap-surface plasmons (GSPs......) that are confined laterally between the tapered groove sidewalls and propagate either along the groove axis or normal to the planar surface, and channeled plasmon polaritons (CPPs) that occupy the tapered groove profile and propagate exclusively along the groove axis. Both GSPs and CPPs exhibit an assortment...... platform to explore the fundamental science of plasmon excitations and their interactions. In this Review, we provide a research status update of plasmons in tapered grooves, starting with a presentation of the theory and important features of GSPs and CPPs, and follow with an overview of the broad range...

  10. Feasibility of Reusable Continuous Thrust Spacecraft for Cargo Resupply Missions to Mars

    Science.gov (United States)

    Rabotin, C. B.

    does not include any optimal trajectory design. For this research, a highly configurable orbit propagation software with SPICE ephemerides was developed from scratch in Go, a modern compiled computer language. The outcome of this research is that simple orbital element control laws do not lead to more efficient or faster interplanetary transfers. In addition, spiraling out of Earth's gravity wells requires a substantial amount of time despite starting from a highly elliptical orbit, and even with clustered high thrust engines like the VASIMR VX-200. Further investigation should look into hybrid solutions with a chemical engine for departing Earth; outbound spirals from Mars take a more reasonable amount of time.

  11. The Motion of a Material Point in a Newtonian Field under the Action of Equiangular Thrust

    Science.gov (United States)

    Leontiev, V. A.; Smolnikov, B. A.

    2004-07-01

    The problems of investigation and optimization of the motion of spacecraft are extensively discussed in the literature. Nevertheless, in many cases a large variety of qualitative characteristics of their motion and of the form of their trajectories are still unclear. In this paper we consider a plane equiangular acceleration of a spacecraft both in a Newtonian field and in its absence (at a large distance from the center of attraction). The general equation of a trajectory of plane acceleration is presented with the introduction of a new variable, an index of an exponent, which allows one to obtain convenient solutions at different values of the time-independent angle of inclination of the vector of thrust to the spacecraft's radius vector (i.e., when equiangular acceleration takes place). Asymptotic solutions are constructed and an interesting fact is revealed. Namely, it is shown that when the center of attraction exists or is absent, for all initial conditions the trajectories appearing at the above equiangular acceleration of a material point tend to the standard logarithmic spirals at a large distance from the center. Specifically, when the value of transverse (perpendicular to the radius vector) thrust is constant, there appears a logarithmic spiral with an angle of inclination to the radius vector equal to 35.264°. Different forms of the trajectory of equiangular acceleration of spacecraft at a low thrust are also studied. The results obtained can be useful for the investigation and choice of optimum space trajectories.

  12. Dynamics of self-organized rotating spiral-coils in bacterial swarms.

    Science.gov (United States)

    Lin, Szu-Ning; Lo, Wei-Chang; Lo, Chien-Jung

    2014-02-07

    Self-propelled particles (SPP) exhibit complex collective motions, mimicking autonomous behaviors that are often seen in the natural world, but essentially are generated by simple mutual interactions. Previous research on SPP systems focuses on collective behaviors of a uniform population. However, very little is known about the evolution of individual particles under the same global influence. Here we show self-organized rotating spiral coils in a two-dimensional (2D) active system. By using swarming bacteria Vibrio alginolyticus as an ideal experimental realization of a well-controlled 2D self-propelled system, we study the interaction between ultra-long cells and short background active cells. The self-propulsion of long cells and their interactions with neighboring short cells leads to a self-organized, stable spiral rotational state in 2D. We find four types of spiral coils with two main features: the rotating direction (clockwise or counter-clockwise) and the central structure (single or double spiral). The body length of the spiral coils falls between 32 and 296 μm and their rotational speed is within a range from 2.22 to 22.96 rad s(-1). The dynamics of these spiral coils involves folding and unfolding processes, which require local velocity changes of the long bacterium. This phenomenon can be qualitatively replicated by a Brownian dynamics simulation using a simple rule of the propulsion thrust, imitating the reorientation of bacterial flagella. Apart from the physical and biological interests in swarming cells, the formation of self-organized spiral coils could be useful for the next generation of microfabrication.

  13. Flow instability in flow past O-grooved circular cylinder

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jaehee; Yang, Kyungsoo [Inha University, Inchun (Korea, Republic of)

    2015-04-15

    This study was devoted to elucidating the change in the flow characteristics of a laminar flow past a circular cylinder by modifying the cylinder shape with O-grooves. A numerical analysis was performed in a two-dimensional framework. The cylinder was represented using an immersed boundary method and marker particles on a Cartesian grid system. The number and locations of the O-grooves were the key parameters. An analysis of the flow pattern and flow induced forces was performed at Re = 40 and 50. In addition, we calculated the critical Reynolds number depending on the number of O-grooves and their locations.

  14. Grooved Fuel Rings for Nuclear Thermal Rocket Engines

    Science.gov (United States)

    Emrich, William

    2009-01-01

    An alternative design concept for nuclear thermal rocket engines for interplanetary spacecraft calls for the use of grooved-ring fuel elements. Beyond spacecraft rocket engines, this concept also has potential for the design of terrestrial and spacecraft nuclear electric-power plants. The grooved ring fuel design attempts to retain the best features of the particle bed fuel element while eliminating most of its design deficiencies. In the grooved ring design, the hydrogen propellant enters the fuel element in a manner similar to that of the Particle Bed Reactor (PBR) fuel element.

  15. Anterior Interhemispheric Approach for Olfactory Groove Meningioma

    Directory of Open Access Journals (Sweden)

    Imam Hidayat

    2016-09-01

    Full Text Available Objective: To evaluate the surgical technique with bifrontal interhemispheric approach for total removal of tumor in olfactory groove meningioma (OGM. Methods: This study described a case of a 38-year-old woman with bilateral blindness, anosmia, and behaviour changes. Imaging studies show a tumor mass in midfrontal base. Surgery using a bifrontal interhemispheric approach was performed and total removal was achieved and postoperative computed tomography (CT scan was performed to confirm the result. Histopathological findings established a diagnosis of meningioma. Results: A coronal skin incision behind the hairline was utilized. The scalp was elevated, taking care to reserve the vascularized pericranium medial to the linea temporalis of each side, and preserving the 2 supraorbital nerves. Eight burr holes were used, with the two initial holes made on each side of the orbitotemporal region, and the other four holes at the midline. A bifrontal craniotomy was performed. The tumor was first detached from its attachment with bipolar cautery and debulked. During this step, the main tumor feeder arteries from the anterior and posterior ethmoidal artery were interrupted, and the tumor devascularized. Total tumor removal through surgical intervention was achieved and confirmed by head CT-scan postoperatively. Conclusions: This case report supports the suitability of the bifrontal interhemispheric approach for OGM resection with additional radiation therapy.

  16. Distinguishing thrust sequences in gravity-driven fold and thrust belts

    Science.gov (United States)

    Alsop, G. I.; Weinberger, R.; Marco, S.

    2018-04-01

    Piggyback or foreland-propagating thrust sequences, where younger thrusts develop in the footwalls of existing thrusts, are generally assumed to be the typical order of thrust development in most orogenic settings. However, overstep or 'break-back' sequences, where later thrusts develop above and in the hangingwalls of earlier thrusts, may potentially form during cessation of movement in gravity-driven mass transport deposits (MTDs). In this study, we provide a detailed outcrop-based analysis of such an overstep thrust sequence developed in an MTD in the southern Dead Sea Basin. Evidence that may be used to discriminate overstep thrusting from piggyback thrust sequences within the gravity-driven fold and thrust belt includes upright folds and forethrusts that are cut by younger overlying thrusts. Backthrusts form ideal markers that are also clearly offset and cut by overlying younger forethrusts. Portions of the basal detachment to the thrust system are folded and locally imbricated in footwall synclines below forethrust ramps, and these geometries also support an overstep sequence. However, new 'short-cut' basal detachments develop below these synclines, indicating that movement continued on the basal detachment rather than it being abandoned as in classic overstep sequences. Further evidence for 'synchronous thrusting', where movement on more than one thrust occurs at the same time, is provided by displacement patterns on sequences of thrust ramp imbricates that systematically increases downslope towards the toe of the MTD. Older thrusts that initiate downslope in the broadly overstep sequence continue to move and therefore accrue greater displacements during synchronous thrusting. Our study provides a template to help distinguish different thrust sequences in both orogenic settings and gravity-driven surficial systems, with displacement patterns potentially being imaged in seismic sections across offshore MTDs.

  17. Analysis of short squeeze film dampers with a central groove

    Science.gov (United States)

    San Andres, Luis A.

    1992-10-01

    A novel analysis for the dynamic force response of a squeeze film damper with a central feeding groove considers the dynamic flow interaction between the squeeze film lands and the feeding groove. For small amplitude centered motions and based on the short bearing model, corrected values for the damping and inertia force coefficients are determined. Correlations with existing experimental evidence is excellent. Analytical results show that the grooved-damper behaves at low frequencies as a single land damper. Dynamic force coefficients are determined to be frequency dependent. Analytical predictions show that the combined action of fluid inertia and groove volume-liquid compressibility affects the force coefficients for dynamic excitation at large frequencies.

  18. V-groove plasmonic waveguides fabricated by nanoimprint lithography

    DEFF Research Database (Denmark)

    Fernandez-Cuesta, I.; Nielsen, R.B.; Boltasseva, Alexandra

    2007-01-01

    Propagation of channel plasmon-polariton modes in the bottom of a metal V groove has been recently demonstrated. It provides a unique way of manipulating light at nanometer length scale. In this work, we present a method based on nanoimprint lithography that allows parallel fabrication of integra...... of integrated optical devices composed of metal V grooves. This method represents an improvement with respect to previous works, where the V grooves were fabricated by direct milling of the metal, in terms of robustness and throughput. © 2007 American Vacuum Society......Propagation of channel plasmon-polariton modes in the bottom of a metal V groove has been recently demonstrated. It provides a unique way of manipulating light at nanometer length scale. In this work, we present a method based on nanoimprint lithography that allows parallel fabrication...

  19. Interproximal grooving in the Atapuerca-SH hominid dentitions.

    Science.gov (United States)

    Bermúdez de Castro, J M; Arsuaga, J L; Pérez, P J

    1997-03-01

    The dental sample recovered from the Sima de los Huesos (SH) Middle Pleistocene cave site of the Sierra de Atapuerca (Spain) includes 296 specimens. Interproximal wear grooves have been observed in 20 maxillary and mandibular posterior teeth belonging to at least five of the 32 individuals identified so far in the SH hypodigm. Interproximal grooving affected only the adults, and at an age between 25 and 40 years. The appearance, morphology, and location pattern of the SH wear grooves are similar to those reported in other fossil hominids and in more recent human populations. Two alternative proposals, the toothpicking and the fiber or sinew processing hypotheses, compete for explaining the formation of this anomalous wear. The characteristics observed in the wear grooves of the SH teeth are compatible only with the habitual probing of interdental spaces by means of hard and inflexible objects. Dietary grit may also have contributed to the abrasion of the root walls during the motion of the dental probes.

  20. Low surface brightness spiral galaxies

    International Nuclear Information System (INIS)

    Romanishin, W.

    1980-01-01

    This dissertation presents an observational overview of a sample of low surface brightness (LSB) spiral galaxies. The sample galaxies were chosen to have low surface brightness disks and indications of spiral structure visible on the Palomar Sky Survey. They are of sufficient angular size (diameter > 2.5 arcmin), to allow detailed surface photometry using Mayall 4-m prime focus plates. The major findings of this dissertation are: (1) The average disk central surface brightness of the LSB galaxies is 22.88 magnitude/arcsec 2 in the B passband. (2) From broadband color measurements of the old stellar population, we infer a low average stellar metallicity, on the order of 1/5 solar. (3) The spectra and optical colors of the HII regions in the LSB galaxies indicate a lack of hot ionizing stars compared to HII regions in other late-type galaxies. (4) The average surface mass density, measured within the radius containing half the total mass, is less than half that of a sample of normal late-type spirals. (5) The average LSB galaxy neutral hydrogen mass to blue luminosity ratio is about 0.6, significantly higher than in a sample of normal late-type galaxies. (6) We find no conclusive evidence of an abnormal mass-to-light ratio in the LSB galaxies. (7) Some of the LSB galaxies exhibit well-developed density wave patterns. (8) A very crude calculation shows the lower metallicity of the LSB galaxies compared with normal late-type spirals might be explained simply by the deficiency of massive stars in the LSB galaxies

  1. [Developmental radicular groove as a cause of endodontic failure].

    Science.gov (United States)

    Fabra Campos, H; Millet Part, J

    1989-01-01

    A clinical case of apical injury on an upper lateral incisor with endodontical and surgical failures in its treatment is presented. Extraction of the incisor and its study at the stereoscopic microscope showed the existence of a developmental groove running from the cingulum to the end of the root, establishing a communication between the crevice and the apical part of the tooth. Bacterial infection through the groove could provide an explanation for treatment failure.

  2. Multiple mechanisms quench passive spiral galaxies

    Science.gov (United States)

    Fraser-McKelvie, Amelia; Brown, Michael J. I.; Pimbblet, Kevin; Dolley, Tim; Bonne, Nicolas J.

    2018-02-01

    We examine the properties of a sample of 35 nearby passive spiral galaxies in order to determine their dominant quenching mechanism(s). All five low-mass (M⋆ environments. We postulate that cluster-scale gas stripping and heating mechanisms operating only in rich clusters are required to quench low-mass passive spirals, and ram-pressure stripping and strangulation are obvious candidates. For higher mass passive spirals, while trends are present, the story is less clear. The passive spiral bar fraction is high: 74 ± 15 per cent, compared with 36 ± 5 per cent for a mass, redshift and T-type matched comparison sample of star-forming spiral galaxies. The high mass passive spirals occur mostly, but not exclusively, in groups, and can be central or satellite galaxies. The passive spiral group fraction of 74 ± 15 per cent is similar to that of the comparison sample of star-forming galaxies at 61 ± 7 per cent. We find evidence for both quenching via internal structure and environment in our passive spiral sample, though some galaxies have evidence of neither. From this, we conclude no one mechanism is responsible for quenching star formation in passive spiral galaxies - rather, a mixture of mechanisms is required to produce the passive spiral distribution we see today.

  3. CAMELOT: Computational-Analytical Multi-fidElity Low-thrust Optimisation Toolbox

    Science.gov (United States)

    Di Carlo, Marilena; Romero Martin, Juan Manuel; Vasile, Massimiliano

    2018-03-01

    Computational-Analytical Multi-fidElity Low-thrust Optimisation Toolbox (CAMELOT) is a toolbox for the fast preliminary design and optimisation of low-thrust trajectories. It solves highly complex combinatorial problems to plan multi-target missions characterised by long spirals including different perturbations. To do so, CAMELOT implements a novel multi-fidelity approach combining analytical surrogate modelling and accurate computational estimations of the mission cost. Decisions are then made using two optimisation engines included in the toolbox, a single-objective global optimiser, and a combinatorial optimisation algorithm. CAMELOT has been applied to a variety of case studies: from the design of interplanetary trajectories to the optimal de-orbiting of space debris and from the deployment of constellations to on-orbit servicing. In this paper, the main elements of CAMELOT are described and two examples, solved using the toolbox, are presented.

  4. Dielectric Barrier Discharge (DBD) Plasma Actuators Thrust-Measurement Methodology Incorporating New Anti-Thrust Hypothesis

    Science.gov (United States)

    Ashpis, David E.; Laun, Matthew C.

    2014-01-01

    We discuss thrust measurements of Dielectric Barrier Discharge (DBD) plasma actuators devices used for aerodynamic active flow control. After a review of our experience with conventional thrust measurement and significant non-repeatability of the results, we devised a suspended actuator test setup, and now present a methodology of thrust measurements with decreased uncertainty. The methodology consists of frequency scans at constant voltages. The procedure consists of increasing the frequency in a step-wise fashion from several Hz to the maximum frequency of several kHz, followed by frequency decrease back down to the start frequency of several Hz. This sequence is performed first at the highest voltage of interest, then repeated at lower voltages. The data in the descending frequency direction is more consistent and selected for reporting. Sample results show strong dependence of thrust on humidity which also affects the consistency and fluctuations of the measurements. We also observed negative values of thrust or "anti-thrust", at low frequencies between 4 Hz and up to 64 Hz. The anti-thrust is proportional to the mean-squared voltage and is frequency independent. Departures from the parabolic anti-thrust curve are correlated with appearance of visible plasma discharges. We propose the anti-thrust hypothesis. It states that the measured thrust is a sum of plasma thrust and anti-thrust, and assumes that the anti-thrust exists at all frequencies and voltages. The anti-thrust depends on actuator geometry and materials and on the test installation. It enables the separation of the plasma thrust from the measured total thrust. This approach enables more meaningful comparisons between actuators at different installations and laboratories. The dependence on test installation was validated by surrounding the actuator with a large diameter, grounded, metal sleeve.

  5. Kinetics of thermal grooving during low temperature recrystallization of pure aluminum

    DEFF Research Database (Denmark)

    Zhang, Yubin; Godfrey, Andy; Juul Jensen, Dorte

    2013-01-01

    . Thermal grooving associated with boundary migration on the inspected free surface was characterized after the in-situ experiment using atomic force microscopy. The results show that new thermal grooves develop at places where the recrystallization boundary segments remain stationary for a relatively long...... time. The kinetics of thermal grooving are determined. Effects of the surface oxidation layer on the formation of thermal grooving as well as the overall influence of grooves on boundary migration are discussed. © (2013) Trans Tech Publications, Switzerland....

  6. Ion implantation planar in targets with semi-cylindrical grooves

    International Nuclear Information System (INIS)

    Filiz, Y.; Demokan, O.

    2002-01-01

    The experimental and numerical investigations suggest that the ion-matrix phase of the sheath evolution plays a crucial role in determining the ion flux to the target surfaces . It can easily be realized that conformal mapping of the target's surface by the sheath is questionable, or even inapplicable in the case of surfaces with fine irregularities or this continuities. The theoretical analysis of such cases is evidently quite complicated. On the other hand, most actual targets fall into this category, and hence, the understanding of the corresponding sheath behavior remains vital for accomplishing uniform implantation. The ion- matrix sheaths have been treated analytically by Conrad for planar, cylindrical and spherical targets successfully. Similar y, Sheridan and Zang et al. have investigated the ion matrix sheath in cylindrical bores, without and with axial electrodes, respectively. All these works assumed targets with infinite areas or length, Zeng et al. and Kwok et al. have started studying implantation into grooves, by carrying out simulations for the inner and outer races of bearings, which are modeled as semi- cylinders of infinite length. Finally, Demokan has presented the first analytic treatment of on matrix sheaths in two- dimensions, by considering targets with rectangular grooves of infinite length, representing a broad range of industrial items. In this work, ion-matrix sheath near infinite length are theoretically analysed. Understanding the sheath formation near such targets is essential for achieving successful ion implantation on the surfaces of a broad range of industrial products, including all types of bearings. The potential profiles both inside and outside the groove are derived and the consequent ion velocity higher plasma densities may improve the uniformity of implantation on the surfaces of such grooves. Furthermore, the sheath edge deformation due to the grooves, the variation of the angle of incidence on the surface of the groove

  7. Spiral 2 the scientific objectives

    International Nuclear Information System (INIS)

    2006-06-01

    The French ministry of research took the decision to build Spiral-2 in May 2005. Its construction costs are estimated to 130 million euros while its operating costs will near 8.5 million euros per year. The construction works will last 5 years. The Spiral-2 facility is based on a high power, superconducting driver Linac, which will deliver a high intensity, 40 MeV deuteron beam as well as a variety of heavy-ion beams with mass over charge ratio equal to 3 and energy up to 14.5 MeV/nucleon. Using a carbon converter, fast neutrons from the breakup of the 5 mA of deuterons impinging on a uranium carbide target will induce a rate of up to 10 14 fissions/s. The radioactive ion beam intensities in the mass range from A = 60 to 140 will be of the order of 10 6 to 10 11 particles/s surpassing by one or two orders-of-magnitude any existing facility in the world. A direct irradiation of the UC 2 target with 3,4 He, 6,7 Li or 12 C may also be used. Different production targets will be used to produce high-intensity beams of light radioactive species with the Isol technique. The extracted radioactive ion beam will be accelerated to energies up to 20 MeV/nucleons by the existing Cime cyclotron. One of the most important features of the future Ganil accelerator complex will be the capability of delivering up to 5 stable or radioactive beams simultaneously in the energy range from the keV to several tens of MeV/nucleons. The document details also the future contribution of Spiral-2 concerning the structure of exotic nuclei, the thermodynamical aspects of nuclear matter, nucleosynthesis, the fundamental basic interactions, and the use of neutrons. (A.C.)

  8. Spiral 2 the scientific objectives

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-06-15

    The French ministry of research took the decision to build Spiral-2 in May 2005. Its construction costs are estimated to 130 million euros while its operating costs will near 8.5 million euros per year. The construction works will last 5 years. The Spiral-2 facility is based on a high power, superconducting driver Linac, which will deliver a high intensity, 40 MeV deuteron beam as well as a variety of heavy-ion beams with mass over charge ratio equal to 3 and energy up to 14.5 MeV/nucleon. Using a carbon converter, fast neutrons from the breakup of the 5 mA of deuterons impinging on a uranium carbide target will induce a rate of up to 10{sup 14} fissions/s. The radioactive ion beam intensities in the mass range from A = 60 to 140 will be of the order of 10{sup 6} to 10{sup 11} particles/s surpassing by one or two orders-of-magnitude any existing facility in the world. A direct irradiation of the UC{sub 2} target with {sup 3,4}He, {sup 6,7}Li or {sup 12}C may also be used. Different production targets will be used to produce high-intensity beams of light radioactive species with the Isol technique. The extracted radioactive ion beam will be accelerated to energies up to 20 MeV/nucleons by the existing Cime cyclotron. One of the most important features of the future Ganil accelerator complex will be the capability of delivering up to 5 stable or radioactive beams simultaneously in the energy range from the keV to several tens of MeV/nucleons. The document details also the future contribution of Spiral-2 concerning the structure of exotic nuclei, the thermodynamical aspects of nuclear matter, nucleosynthesis, the fundamental basic interactions, and the use of neutrons. (A.C.)

  9. The rotation of spiral galaxies.

    Science.gov (United States)

    Rubin, V C

    1983-06-24

    There is accumulating evidence that as much as 90 percent of the mass of the universe is nonluminous and is clumped, halo-like, around individual galaxies. The gravitational force of this dark matter is presumed to be responsible for the high rotational velocities of stars and gas in the disks of spiral galaxie. At present, the form of the dark matter is unknown. Possible candidates span a range in mass of 10(70), from non-zero-mass neutrinos to massive black holes.

  10. Measuring Model Rocket Engine Thrust Curves

    Science.gov (United States)

    Penn, Kim; Slaton, William V.

    2010-01-01

    This paper describes a method and setup to quickly and easily measure a model rocket engine's thrust curve using a computer data logger and force probe. Horst describes using Vernier's LabPro and force probe to measure the rocket engine's thrust curve; however, the method of attaching the rocket to the force probe is not discussed. We show how a…

  11. Continuous blood fractionation using an array of slanted grooves

    Science.gov (United States)

    Bernate, Jorge A.; Chengxun, Liu; Lagae, Liesbet; Drazer, German

    2011-11-01

    Blood is a complex fluid having different specialized biological functions and containing a plethora of clinical information. The separation of different blood components is a crucial step in many research and clinical applications. In this work we take advantage of the flow characteristics in microfluidic devices in which the bottom surface is patterned with slanted rectangular grooves to continuously fractionate blood. We exploit the flow in the vicinity of the patterned surface when the dimensions of the grooves are much smaller than the dimensions of the main channel. In these devices, we observed that the grooves act as open channels guiding flow along them with the flow over them being in the direction of the main channel. We present experiments in which the different blood components are deflected laterally to a different extent by the flow along the grooves depending on their sedimentation velocity, which allows their continuous fractionation. In particular, the heavier red blood cells experience the largest deflection while the lighter white blood cells deflect the least, allowing their passive and minimally invasive isolation. In addition, this fluidic platform can also be used to separate magnetically labeled circulating cancer cells which can be retained in the flow along the grooves using a sufficiently strong magnetic force.

  12. Documentation of roller-bearing effect on butterfly inspired grooves

    Science.gov (United States)

    Gautam, Sashank; Lang, Amy

    2017-11-01

    Butterfly wings are covered with scales in a roof shingle pattern which align together to form grooves. The increase or decrease of laminar friction drag depends on the flow orientation to the scales. Flow in the longitudinal direction to the grooves encounters increased surface area which increases the friction drag. However, in the transverse direction, for low Re laminar flow, a single vortex is formed inside each groove and is predicted to remain stable due to the very low Re of the flow in each cavity. These embedded vortices act as roller bearings to the flow above, such that the fluid from the outer boundary layer does not mix with fluid inside the cavities. This leads to a reduction of skin friction drag when compared to a smooth surface. When the cavity flow Re is increased beyond a critical point, the vortex becomes unstable and the low-momentum fluid in the grooves mixes with the outer boundary layer flow, increasing the drag. The objective of this experiment is to determine the critical Re where the embedded vortex transitions from a stable to an unstable state using DPIV. Subsequently, for steady vortex conditions, a comparison of skin friction drag between the grooved and flat plate can show that the butterfly scaled surface can result in sub-laminar friction drag. The National Science Foundation (Grant No. 1335848).

  13. Correction of Brassiere Strap Grooves with Fat Injections.

    Science.gov (United States)

    Ergün, Selma Sönmez; Baygöl, Emre Gönenç; Kayan, Reşit Burak; Kuzu, İsmail Melih; Akman, Onur

    2015-07-01

    The size and weight of hypertrophied breast can cause both physical and psychological problems. Although the majority of these problems can be solved with breast reduction surgery, the particular problem of development of brassiere strap grooves on the shoulders due to the weight of the breasts cannot be corrected with this method. Breast reduction surgery focuses only on the increased dimensions of breasts: fullness of the thoracic wall lateral to the breasts, as well as the appearance of brassiere strap grooves, need to be taken into consideration to obtain a better upper body image. Therefore, we present a series of 10 female patients who were treated with fat injections for the correction of brassiere strap grooves. Reduction mammaplasty and fat injections into the brassiere strap grooves were performed during the same session. Dramatic changes are obtained with judicious placement of fat into the bra strap grooves. A more aesthetic and harmonious look can be obtained with using these combined aesthetic procedures in appropriately selected patients. 4 Therapeautic. © 2015 The American Society for Aesthetic Plastic Surgery, Inc. Reprints and permission: journals.permissions@oup.com.

  14. Performance optimization of grooved slippers for aero hydraulic pumps

    Directory of Open Access Journals (Sweden)

    Juan Chen

    2016-06-01

    Full Text Available A computational fluid dynamics (CFD simulation method based on 3-D Navier–Stokes equation and Arbitrary Lagrangian–Eulerian (ALE method is presented to analyze the grooved slipper performance of piston pump. The moving domain of grooved slipper is transformed into a fixed reference domain by the ALE method, which makes it convenient to take the effects of rotate speed, body force, temperature, and oil viscosity into account. A geometric model to express the complex structure, which covers the orifice of piston and slipper, vented groove and the oil film, is constructed. Corresponding to different oil film thicknesses calculated in light of hydrostatic equilibrium theory and boundary conditions, a set of simulations is conducted in COMSOL to analyze the pump characteristics and effects of geometry (groove width and radius, orifice size on these characteristics. Furthermore, the mechanics and hydraulics analyses are employed to validate the CFD model, and there is an excellent agreement between simulation and analytical results. The simulation results show that the sealing land radius, orifice size and groove width all dramatically affect the slipper behavior, and an optimum tradeoff among these factors is conducive to optimizing the pump design.

  15. Lattice Boltzmann study of droplet motion inside a grooved channel

    Science.gov (United States)

    Huang, Jun Jie; Shu, Chang; Chew, Yong Tian

    2009-02-01

    A droplet moving inside a grooved channel is studied by using a new lattice Boltzmann model for multiphase flows with large density ratio. A constant body force is applied to drive the droplet. Flows under different surface tensions, driving forces, density ratios, wall wettabilities, and groove geometries are investigated. It is found that the drag on the droplet and the flow pattern are strongly affected by the wall wettability and topography when the system scale is small. The effects of the driving force on the droplet are investigated through comparison of two different ways of applying it. Besides, the density ratio is varied over a wide range to assess its effects in the present setup. Special attention is paid to grooved hydrophilic walls which tend to enhance the droplet-wall contact. For such walls, two distinctive types of shape of the interface inside the groove are found and series of numerical investigations are carried out to find the critical wall contact angle, groove width and depth that determine which kind of shape the droplet assumes. Some typical cases are chosen for detailed analyses and compared to some other work. This study is expected to improve our understanding on the lotus effect and the physics of small scale flows near rough walls.

  16. Design of pellet surface grooves for fission gas plenum

    International Nuclear Information System (INIS)

    Carter, T.J.; Jones, L.R.; Macici, N.; Miller, G.C.

    1986-01-01

    In the Canada deuterium uranium pressurized heavy water reactor, short (50-cm) Zircaloy-4 clad bundles are fueled on-power. Although internal void volume within the fuel rods is adequate for the present once-through natural uranium cycle, the authors have investigated methods for increasing the internal gas storage volume needed in high-power, high-burnup, experimental ceramic fuels. This present work sought to prove the methodology for design of gas storage volume within the fuel pellets - specifically the use of grooves pressed or machined into the relatively cool pellet/cladding interface. Preanalysis and design of pellet groove shape and volume was accomplished using the TRUMP heat transfer code. Postirradiation examination (PIE) was used to check the initial design and heat transfer assumptions. Fission gas release was found to be higher for the grooved pellet rods than for the comparison rods with hollow or unmodified pellets. This had been expected from the initial TRUMP thermal analyses. The ELESIM fuel modeling code was used to check in-reactor performance, but some modifications were necessary to accommodate the loss of heat transfer surface to the grooves. It was concluded that for plenum design purposes, circumferential pellet grooves could be adequately modeled by the codes TRUMP and ELESIM

  17. The thickness effects of the side-grooved CCT specimen

    International Nuclear Information System (INIS)

    Machida, Kenji; Kikuchi, Masanori; Miyamoto, Hiroshi

    1988-01-01

    J IC tests were carried out on SUS 316 steel by means of the JSME R-curve method as well as the JSME stretched-zone width (SZW) method. The effects of side-grooves on the J in value at the onset of stable crack growth were investigated using CCT specimens of two thicknesses (B = 1 mm and 2 mm). The ratio of the net thickness to the gross thickness was maintained at 0.5. The J in values of the side-grooved CCT specimens of both thicknesses were considerably smaller than those of the 1 TCT specimen. The J in value of the side-grooved specimen of 2 mm thickness was smaller than that of the standard CCT specimen. Further, as the thickness of the specimen became thinner, the J in value decreased. In the case of 1 mm-thick CCT specimens with or without a side-groove, the contraction percentage of thickness was very large so that it was not appropriate to use these specimens for the fracture toughness test. In the case of the thin or side-grooved CCT specimens, the J-value, which is evaluated from the load versus displacement curve using Rice's formula, cannot estimate the J-integral at the central part of the specimen. Therefore, a J-integral estimation method would have to be established using 3-D elastic-plastic analysis. (author)

  18. Osteochondritis Dissecans Involving the Trochlear Groove Treated With Retrograde Drilling

    Science.gov (United States)

    Kaji, Yoshio; Nakamura, Osamu; Yamaguchi, Konosuke; Yamamoto, Tetsuji

    2015-01-01

    Abstract Osteochondritis dissecans (OCD) occurs frequently in the humeral capitellum of the upper extremity, whereas OCD involving the trochlear groove (trochlear groove OCD) is rarely reported. A standard treatment for trochlear groove OCD has therefore not been determined, although several methods have been tried. The case of a 14-year-old male gymnast with bilateral trochlear groove OCD is presented. Retrograde drilling from the lateral condyle of the humerus was applied for the OCD lesion of the left elbow, since it was larger in size than that in the right elbow and was symptomatic. Conversely, since the right lesion was small and asymptomatic, it was managed conservatively. After treatment, consolidation of the OCD lesions was observed in both elbows. However, the time to healing was shorter in the left elbow treated surgically than in the right elbow managed conservatively. In conclusion, retrograde drilling is a very simple and minimally invasive treatment. This case suggests that retrograde drilling for trochlear groove OCD may be a useful procedure that may accelerate the healing process for OCD lesions. PMID:26356703

  19. The DESIR Facility at SPIRAL2

    Indian Academy of Sciences (India)

    Beams from the low-energy branch of the separator spectrometer S3 and from SPIRAL1 will allow complementary studies of refrac- tory elements produced by means of fusion reactions as well as of light and intense exotic beams, respectively. Keywords. SPIRAL2; low-energy facility; nuclear physics; weak interaction; astro-.

  20. ANGULAR-MOMENTUM IN BINARY SPIRAL GALAXIES

    NARCIS (Netherlands)

    OOSTERLOO, T

    In order to investigate the relative orientations of spiral galaxies in pairs, the distribution of the angle between the spin-vectors for a new sample of 40 binary spiral galaxies is determined. From this distribution it is found, contrary to an earlier result obtained by Helou (1984), that there is

  1. Scaling effects in spiral capsule robots.

    Science.gov (United States)

    Liang, Liang; Hu, Rong; Chen, Bai; Tang, Yong; Xu, Yan

    2017-04-01

    Spiral capsule robots can be applied to human gastrointestinal tracts and blood vessels. Because of significant variations in the sizes of the inner diameters of the intestines as well as blood vessels, this research has been unable to meet the requirements for medical applications. By applying the fluid dynamic equations, using the computational fluid dynamics method, to a robot axial length ranging from 10 -5 to 10 -2  m, the operational performance indicators (axial driving force, load torque, and maximum fluid pressure on the pipe wall) of the spiral capsule robot and the fluid turbulent intensity around the robot spiral surfaces was numerically calculated in a straight rigid pipe filled with fluid. The reasonableness and validity of the calculation method adopted in this study were verified by the consistency of the calculated values by the computational fluid dynamics method and the experimental values from a relevant literature. The results show that the greater the fluid turbulent intensity, the greater the impact of the fluid turbulence on the driving performance of the spiral capsule robot and the higher the energy consumption of the robot. For the same level of size of the robot, the axial driving force, the load torque, and the maximum fluid pressure on the pipe wall of the outer spiral robot were larger than those of the inner spiral robot. For different requirements of the operating environment, we can choose a certain kind of spiral capsule robot. This study provides a theoretical foundation for spiral capsule robots.

  2. QS Spiral: Visualizing Periodic Quantified Self Data

    DEFF Research Database (Denmark)

    Larsen, Jakob Eg; Cuttone, Andrea; Jørgensen, Sune Lehmann

    2013-01-01

    In this paper we propose an interactive visualization technique QS Spiral that aims to capture the periodic properties of quantified self data and let the user explore those recurring patterns. The approach is based on time-series data visualized as a spiral structure. The interactivity includes ...

  3. Method of forming grooves in the [011] crystalline direction

    Science.gov (United States)

    Marinelli, Donald Paul (Inventor)

    1977-01-01

    An A-B etchant is applied to a (100) surface of a body of semiconductor material, a portion of which along the (100) surface of the body is either gallium arsenide or gallium aluminum arsenide. The etchant is applied for at least 15 seconds at a temperature of approximately 80.degree. C. The A-B etchant is a solution by weight percent of 47.5%, water, 0.2% silver nitrate, 23.8% chromium trioxide and 28.5% of a 48% aqueous solution of hydrofluoric acid. As a result of the application of the A-B etchant a pattern of elongated etch pits form having their longitudinal axes along the [011] crystalline direction. Grooves are formed in the body at a surface opposite the (100) surface on which was applied the etchant. The grooves are formed along the [011] crystalline direction by aligning the longitudinal axes of the grooves with the longitudinal axes of the etch pits.

  4. Atypical olfactory groove meningioma associated with uterine fibromatosis; case report

    Directory of Open Access Journals (Sweden)

    Toma I. Papacocea

    2016-11-01

    Full Text Available The concomitant presence of the olfactory groove meningioma with uterine fibrosis is very rare. Our report presents the case of a giant olfactory groove meningioma revealed after a uterine fibroma resection in a 44 years-old female, due to a generalized seizure 10 days after operation. Cranial CT-scan identified the tumor as an olfactory groove meningioma. The tumor was operated with a macroscopically complete resection; the endothermal coagulation of the dura attachment was performed (Simpson II with a good postoperative evolution. Laboratory results showed the presence of receptors for steroid hormones both in meningioma and uterine tumor, and the histopathological examination revealed an atypical meningioma with 17% proliferation markers. Our findings suggest that even though meningiomas are benign tumors and a complete resection usually indicates a good prognosis, the association with uterine fibromatosis and the presence of high percentage of steroid receptors creates a higher risk to relapse, imposing therefore a good monitoring.

  5. Raphides with barbs and grooves in Xanthosoma sagittifolium (Araceae).

    Science.gov (United States)

    Sakai, W S; Hanson, M; Jones, R C

    1972-10-20

    Raphides in petioles of Xanthosoma sagittifolium are needlelike crystals about 50 micrometers long. The rectangular cross sections have maximum dimensions of approximately 850 by 250 nanometers. The raphides have two distinct end structures. One end is narrow, acute, and tapered to a point; the other is broad, acute, and abruptly pointed. Barbs, about 750 angstroms long with tips oriented away from the narrow end, occur along the length of the raphide on ridges on either side of two longitudinal grooves. These grooves, located opposite each other, give the raphide cross section an H-shape.

  6. Bragg grating filters in plasmonic V-groove waveguides

    DEFF Research Database (Denmark)

    Smith, Cameron; Desiatov, Boris; Goykhmann, Ilya

    2012-01-01

    We demonstrate spectral filtering via Bragg gratings in plasmonic V-groove waveguides. Transmission spectra of wafer-scale fabricated devices exhibit 8.2 dB extinction ratio with 39.9 nm bandwidth. Near-field measurements verify spectral rejection.......We demonstrate spectral filtering via Bragg gratings in plasmonic V-groove waveguides. Transmission spectra of wafer-scale fabricated devices exhibit 8.2 dB extinction ratio with 39.9 nm bandwidth. Near-field measurements verify spectral rejection....

  7. High-aspect-ratio grooves fabricated in silicon by a single pass of femtosecond laser pulses

    International Nuclear Information System (INIS)

    Ma Yuncan; Shi Haitao; Si Jinhai; Ren Hai; Chen Tao; Chen Feng; Hou Xun

    2012-01-01

    High-aspect-ratio grooves have been fabricated in silicon by a single pass of femtosecond laser pulses in water and ambient air. Scanning electron microscopy and energy dispersive x-ray spectroscopy were employed to image for the morphology of the photoinduced grooves and analyze the chemical composition in the surrounding of the grooves. It was observed that the sidewall of the grooves fabricated in water was much smoother than that in ambient air, and there were homogeneous nano-scale protrusions on the sidewall of the grooves fabricated in water. Meanwhile, oxygen species, which was incorporated into the grooves fabricated in air, was not observed in those in water.

  8. Analisa Kekuatan Spiral Bevel Gear Dengan Variasi Sudut Spiral Menggunakan Metode Elemen Hingga

    Directory of Open Access Journals (Sweden)

    Deta Rachmat Andika

    2017-01-01

    Full Text Available Seiring perkembangan zaman,  teknologi roda gigi dituntut untuk mampu mentransmisikan daya yang besar dengan efisiensi yang besar pula. Pada jenis intersecting shaft gear, tipe roda gigi payung spiral (spiral bevel gear  merupakan perkembangan dari roda gigi payung bergigi lurus (straight bevel gear. Kelebihan dari spiral bevel gear antara  lain adalah kemampuan transmisi daya dan efisiensi yang lebih besar pada geometri yang sama serta tidak terlalu berisik. Akan tetapi spiral bevel gear juga mempunyai kelemahan jika dibandingkan dengan straight bevel gear. Selain proses manufaktur yang lebih rumit, profil lengkung gigi spiral ini membuat distribusi tegangan yang terjadi menjadi lebih rumit untuk dimodelkan dengan persamaan matematika. Salah satu pendekatan yang dapat dilakukan adalah dengan menggunakan metode elemen hingga. Penelitian diawali dengan membuat model dari straight bevel gear dan juga spiral bevel gear yang sudut spiralnya divariasikan 20, 35, dan 45 derajat. Model dibuat dengan dimensi yang sama baik diameter maupun jumlah gigi gear. Langkah selanjutnya yaitu perhitungan analitis pada straight bevel gear dimana hasilnya akan dibandingkan dengan hasil simulasi statis. Setelah eror yang terjadi dibawah 15% maka dilakukan simulasi dinamis pada semua model yang telah dibuat yaitu straight bevel dan juga spira bevel gear. Hasil yang didapatkan dari penelitian ini adalah secara keseluruhan spiral bevel gear lebih kuat daripada straight bevel gear pada dimensi dan beban yang sama jika dilihat dari lebih kecilnya tegangan bending dan tegangan kontak maksimum yang terjadi. Tegangan terbesar terjadi pada jenis straight bevel gear baik pada tegangan bending maupun tegangan kontak sedangkan spiral bevel gear dengan variasi sudut Seiring spiral 35 mempunyai nilai tegangan terkecil. Prosntase selisih tegangan bending maksimum yang terjadi antara straight bevel gear dan spiral bevel gear dengan variasi sudut spiral 35 derajat  sebesar 44

  9. The NASA low thrust propulsion program

    Science.gov (United States)

    Stone, James R.; Bennett, Gary L.

    1989-01-01

    The NASA OAST Propulsion, Power, and Energy Division supports a low-thrust propulsion program aimed at providing high-performance options for a broad range of near-term and far-term missions and vehicles. Low-thrust propulsion has a major impact on the mission performance of essentially all spacecraft and vehicles. On-orbit lifetimes, payloads, and trip time are significantly impacted by low-thrust propulsion performance and integration features for earth-to-orbit (ETO) vehicles, earth-orbit and planetary spacecraft, and large platforms in earth orbit. Major emphases are on low-thrust chemical propulsion, both storables and hydrogen/oxygen; low-power (auxiliary) electric arcjets and resistojets; and high-power (primary) electric propulsion, including ion, magnetoplasmadynamic (MPD), and electrodeless concepts. The major recent accomplishments of the program are presented and their impacts discussed.

  10. Combination radial and thrust magnetic bearing

    Science.gov (United States)

    Blumenstock, Kenneth A. (Inventor)

    2002-01-01

    A combination radial and thrust magnetic bearing is disclosed that allows for both radial and thrust axes control of an associated shaft. The combination radial and thrust magnetic bearing comprises a rotor and a stator. The rotor comprises a shaft, and first and second rotor pairs each having respective rotor elements. The stator comprises first and second stator elements and a magnet-sensor disk. In one embodiment, each stator element has a plurality of split-poles and a corresponding plurality of radial force coils and, in another embodiment, each stator element does not require thrust force coils, and radial force coils are replaced by double the plurality of coils serving as an outer member of each split-pole half.

  11. Three dimensional thrust chamber life prediction

    Science.gov (United States)

    Armstrong, W. H.; Brogren, E. W.

    1976-01-01

    A study was performed to analytically determine the cyclic thermomechanical behavior and fatigue life of three configurations of a Plug Nozzle Thrust Chamber. This thrust chamber is a test model which represents the current trend in nozzle design calling for high performance coupled with weight and volume limitations as well as extended life for reusability. The study involved the use of different materials and material combinations to evaluate their application to the problem of low-cycle fatigue in the thrust chamber. The thermal and structural analyses were carried out on a three-dimensional basis. Results are presented which show plots of continuous temperature histories and temperature distributions at selected times during the operating cycle of the thrust chamber. Computed structural data show critical regions for low-cycle fatigue and the histories of strain within the regions for each operation cycle.

  12. On Density Waves in Spiral Galaxies

    Science.gov (United States)

    Grosbol, P.; Patsis, P. A.

    The spiral structure of five ordinary spiral galaxies was studied using deep BVIK' surface photometry maps obtained at the 2.2m ESO/MPI telescope. The detailed shape of the arms was analyzed in terms of the spiral density wave theory. Grand design spirals were found on the K' maps in all five galaxies although at least two would be classified as flocculent on the blue images. In several of the galaxies, bulges with weak oval distortion (~10%) were observed. Dust spirals also continue, in some cases, inside the ILR where the stellar arms terminate. This emphasizes the strong bias of morphological classifications of spiral galaxies based on blue image due to dust and young stars. The 2--armed spirals were systematically found to be wound tighter on I than on K' maps suggesting the existence of a density wave. Locations of the ILR and the 4/1 resonance were estimated based on the arm morphology and the amplitude ratio between the m = 2,4 Fourier components. The wavenumber of the stellar 2--armed pattern is increasing towards the ILR which could suggest that the density wave is associated to the long waved branch of the dispersion relation. A possible scenario is discussed.

  13. Spiral arms in thermally stratified protoplanetary discs

    Science.gov (United States)

    Juhász, Attila; Rosotti, Giovanni P.

    2018-02-01

    Spiral arms have been observed in nearly a dozen protoplanetary discs in near-infrared scattered light and recently also in the submillimetre continuum. While one of the most compelling explanations is that they are driven by planetary or stellar companions, in all but one cases such companions have not yet been detected and there is even ambiguity on whether the planet should be located inside or outside the spirals. Here, we use 3D hydrodynamic simulations to study the morphology of spiral density waves launched by embedded planets taking into account the vertical temperature gradient, a natural consequence of stellar irradiation. Our simulations show that the pitch angle of the spirals in thermally stratified discs is the lowest in the disc mid-plane and increases towards the disc surface. We combine the hydrodynamic simulations with 3D radiative transfer calculations to predict that the pitch angle of planetary spirals observed in the near-infrared is higher than in the submillimetre. We also find that in both cases the spirals converge towards the planet. This provides a new powerful observational method to determine if the perturbing planet is inside or outside the spirals, as well as map the thermal stratification of the disc.

  14. DNA minor groove binding of small molecules: Experimental and ...

    Indian Academy of Sciences (India)

    Administrator

    to DNA have been studied and summarized by several workers. 3–6. Rich, Dervan, Wemmer, Lown and other workers have described Netropsin, Dista- mycin A, and Hoechst-33258, etc. as DNA minor groove binding drugs. 7–10. It is observed that tryptophan and indole do not intercalate with either single-stranded DNA or.

  15. Tailoring channeled plasmon polaritons in metallic V-grooves

    DEFF Research Database (Denmark)

    Smith, Cameron; Thilsted, Anil Haraksingh; Marie, Rodolphe

    2013-01-01

    of propagating plasmons to optimize the trade-off between lateral confinement and loss [2]. Accordingly, the traits of CPPs in metallic V-grooves suggest their widespread implementation, with applications ranging from ultracompact photonic circuitry [3] to lab-on-a-chip sensing. Current CPP research focuses...

  16. Syncopation, body-movement and pleasure in groove music.

    Science.gov (United States)

    Witek, Maria A G; Clarke, Eric F; Wallentin, Mikkel; Kringelbach, Morten L; Vuust, Peter

    2014-01-01

    Moving to music is an essential human pleasure particularly related to musical groove. Structurally, music associated with groove is often characterised by rhythmic complexity in the form of syncopation, frequently observed in musical styles such as funk, hip-hop and electronic dance music. Structural complexity has been related to positive affect in music more broadly, but the function of syncopation in eliciting pleasure and body-movement in groove is unknown. Here we report results from a web-based survey which investigated the relationship between syncopation and ratings of wanting to move and experienced pleasure. Participants heard funk drum-breaks with varying degrees of syncopation and audio entropy, and rated the extent to which the drum-breaks made them want to move and how much pleasure they experienced. While entropy was found to be a poor predictor of wanting to move and pleasure, the results showed that medium degrees of syncopation elicited the most desire to move and the most pleasure, particularly for participants who enjoy dancing to music. Hence, there is an inverted U-shaped relationship between syncopation, body-movement and pleasure, and syncopation seems to be an important structural factor in embodied and affective responses to groove.

  17. Syncopation, body-movement and pleasure in groove music.

    Directory of Open Access Journals (Sweden)

    Maria A G Witek

    Full Text Available Moving to music is an essential human pleasure particularly related to musical groove. Structurally, music associated with groove is often characterised by rhythmic complexity in the form of syncopation, frequently observed in musical styles such as funk, hip-hop and electronic dance music. Structural complexity has been related to positive affect in music more broadly, but the function of syncopation in eliciting pleasure and body-movement in groove is unknown. Here we report results from a web-based survey which investigated the relationship between syncopation and ratings of wanting to move and experienced pleasure. Participants heard funk drum-breaks with varying degrees of syncopation and audio entropy, and rated the extent to which the drum-breaks made them want to move and how much pleasure they experienced. While entropy was found to be a poor predictor of wanting to move and pleasure, the results showed that medium degrees of syncopation elicited the most desire to move and the most pleasure, particularly for participants who enjoy dancing to music. Hence, there is an inverted U-shaped relationship between syncopation, body-movement and pleasure, and syncopation seems to be an important structural factor in embodied and affective responses to groove.

  18. Design optimization of deep groove ball bearings using crowding ...

    Indian Academy of Sciences (India)

    Aparna Duggirala

    2018-02-07

    Feb 7, 2018 ... Abstract. This paper presents a crowding distance particle swarm optimization technique to optimize the design parameters of deep groove ball bearings. The design optimization problem is multi-objective in nature. The considered objectives are maximizing dynamic and static load bearing capacities and ...

  19. Computational analysis of frictional drag over transverse grooved ...

    African Journals Online (AJOL)

    user

    International Journal of Engineering, Science and Technology. Vol. 3, No. 2, 2011, pp. 110-116. INTERNATIONAL. JOURNAL OF .... dissipation) that is adopted by the standard wall function in computing the budget of the turbulence kinetic energy at wall- neighboring cells [3]. Figure 1. Schematic diagram of the grooved ...

  20. Novel scaffold design with multi-grooved PLA fibers

    International Nuclear Information System (INIS)

    Chung, Sangwon; King, Martin W; Gamcsik, Mike P

    2011-01-01

    A novel prototype nonwoven textile structure containing polylactide (PLA) multigrooved fibers has been proposed as a possible scaffold material for superior cell attachment and proliferation. Grooved cross-sectional fibers with larger surface area were obtained by a bi-component spinning system and the complete removal of the sacrificial component was confirmed by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and x-ray photon spectroscopy (XPS) analysis. These PLA nonwoven scaffolds containing the grooved fibers exhibited enhanced wettability, greater flexibility and tensile properties, and a larger surface area compared to a traditional PLA nonwoven fabric containing round fibers. To evaluate cellular attachment on the two types of PLA nonwoven scaffolds, NIH 3T3 fibroblasts were cultured for up to 12 days. It was evident that the initial cellular attachment was superior on the scaffold with grooved fibers, which was confirmed by MTT viability assay (p < 0.01) and SEM analysis. In the future, by modulating the size of the grooves on the fibers, such a scaffold material with a large surface area could serve as an alternative matrix for culturing different types of cells.

  1. Fabrication and Characterization of a Grooved Ring Fuel Element for a Nuclear Thermal Rocket

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed innovation is a new fuel element design that involves a stack of grooved disks, where propellant can flow along the grooves. This design increases...

  2. The influence of mixture composition, adhesion promotor and compaction degree on the groove stability of grooved Marshall asphalt

    Science.gov (United States)

    Vuye, Cedric; Couscheir, Karolien; Lauriks, Leen; Van den bergh, Wim; Van Bouwel, Philippe

    2017-09-01

    After the first rehabilitation of runway 07R/25L in 2015, runway 01/19 was reconstructed in the summer of 2016, as part of a cycle where all runway pavements at Brussels airport are completely renovated each thirty years. The top layer is a Marshall asphalt with a polymer modified bitumen. To optimize the water drainage the central part of the runway (47 m wide) is grooved instead of applying an anti-skid layer. In this paper the focus is on the durability of the grooved top layer. Two different Marshall asphalt mixtures with a different maximum granulate size (10 mm or 14 mm) are compared, both in the laboratory and in a full-scale trial. In the laboratory the resistance against rutting and raveling are investigated for both mixtures with and without adhesion promotor, which did not show a positive effect. In the full-scale trial the compactability and impact of both a longer curing period and a variation in the degree of compaction on the groove stability is investigated for both mixtures using a heavy truck. No visual differences could be found except in areas which were undercompacted and showed more damage to the grooves.

  3. Decametre scale, spiral-shaped landforms in Elysium Planitia, Mars

    Science.gov (United States)

    Balme, M. R.; Gallagher, C.

    2012-04-01

    We present the discovery of a new type of landform that is apparently confined to one or two locations in western Elysium Planitia, Mars. In planview, these landforms consist of spirals, a few tens of metres across, defined by low furrows and ridges. They appear singly or in loose groups or chains and are generally double-armed with a visual similarity to Kelvin-Helmholtz instability forms. About 100 examples have been found, over 90% of which occur in a single image. Almost all the examples seen have "anti-clockwise" rotation (from the edge to the centre); less than a fifth spiral the other way. The spirals are found only in the polygonised elements of a terrain type known as Platy-Ridged-Polygonised (PRP) terrain. This distinctive surface displays a tripartite morphology comprising: 1) well-defined, kilometre-scale plates of rubbly material (clast-sizes up to a few meters in diameters), 2) complex patterns of sinuous to sub-linear rubbly ridges that are often many kilometres long, less than a few tens of metres across and less than a few metres in height, and 3) clast-free zones between the plates that display decametre scale polygonally patterned ground defined by networks of furrows and grooves. PRP terrain appears to represent the "frozen" remnants of a once liquid medium: it is extremely flat with margins defining an equipotential surface; infills craters and drapes low relief terrain; can be traced up through the 300 km long Athabasca Vallis outflow channel to a source region consisting of a pair of large (km-wide) fractures called the Cerberus Fossae. The origin of the PRP material is debated: some authors favour extremely fluid, voluminous and turbulently emplaced lavas (e.g. Keszthelyi et al., Geochem. Geophys. Geosys., 2003), others argue that this material represents a debris-covered relict frozen sea or ocean (e.g. Murray et al., Nature, 2005). The spirals, which are visible only in HiRISE images with sub-metre spatial resolution, have been observed in

  4. The complex radicular groove: interdisciplinary management with mineral trioxide aggregate and bone substitute.

    Science.gov (United States)

    Narmatha, V J; Thakur, Sophia; Shetty, Sheetal; Bali, Praveen Kumar

    2014-11-01

    This article is a case report of the successful interdisciplinary management of a maxillary lateral incisor with a deep palatogingival groove. The tooth presented with severe periodontal destruction owing to the deep extension of the groove up to the root apex. The groove was meticulously diagnosed and treated by endodontic and subsequent periodontal surgery leading to complete resolution of the pathological process.

  5. Corrosion of Spiral Rib Aluminized Pipe

    Science.gov (United States)

    2012-08-01

    Large diameter, corrugated steel pipes are a common sight in the culverts that run alongside many Florida roads. Spiral-ribbed aluminized pipe (SRAP) has been widely specified by the Florida Department of Transportation (FDOT) for runoff drainage. Th...

  6. Corrosion of Spiral Rib Aluminized Pipe : [Summary

    Science.gov (United States)

    2012-01-01

    Large diameter, corrugated steel pipes are a common sight in the culverts that run alongside many Florida roads. Spiral-ribbed aluminized pipe (SRAP) has been widely specified by the Florida Department of Transportation (FDOT) for runoff drainage. Th...

  7. Magnetic spiral arms in galaxy haloes

    Science.gov (United States)

    Henriksen, R. N.

    2017-08-01

    We seek the conditions for a steady mean field galactic dynamo. The parameter set is reduced to those appearing in the α2 and α/ω dynamo, namely velocity amplitudes, and the ratio of sub-scale helicity to diffusivity. The parameters can be allowed to vary on conical spirals. We analyse the mean field dynamo equations in terms of scale invariant logarithmic spiral modes and special exact solutions. Compatible scale invariant gravitational spiral arms are introduced and illustrated in an appendix, but the detailed dynamical interaction with the magnetic field is left for another work. As a result of planar magnetic spirals `lifting' into the halo, multiple sign changes in average rotation measures forming a regular pattern on each side of the galactic minor axis, are predicted. Such changes have recently been detected in the Continuum Halos in Nearby Galaxies-an EVLA Survey (CHANG-ES) survey.

  8. Cylindrical spirals in human skeletal muscle.

    Science.gov (United States)

    Carpenter, S; Karpati, G; Robitaille, Y; Melmed, C

    1979-01-01

    Muscle biopsies from two patients revealed that numerous type 2 fibers contained large abnormal areas filled with cylindrical spirals. The cytochemical profile of these cylindrical spirals was sufficiently characteristic that they could be distinguished from tubular aggregates. Their electron microscopic appearance was unmistakable. Their origin and significance are uncertain. The diverse nature of the patients' conditions (cramps and malignancy, and an unusual form of spinocerebellar degeneration) indicate that these abnormal structures are not disease specific.

  9. Wavelet Scattering on the Pitch Spiral

    OpenAIRE

    Lostanlen, Vincent; Mallat, Stéphane

    2016-01-01

    We present a new representation of harmonic sounds that linearizes the dynamics of pitch and spectral envelope, while remaining stable to deformations in the time-frequency plane. It is an instance of the scattering transform, a generic operator which cascades wavelet convolutions and modulus nonlinearities. It is derived from the pitch spiral, in that convolutions are successively performed in time, log-frequency, and octave index. We give a closed-form approximation of spiral scattering coe...

  10. Dark matter in spiral galaxies

    International Nuclear Information System (INIS)

    Albada, T.S. van; Sancisi, R.

    1986-01-01

    Mass models of spiral galaxies based on the observed light distribution, assuming constant M/L for bulge and disc, are able to reproduce the observed rotation curves in the inner regions, but fail to do so increasingly towards and beyond the edge of the visible material. The discrepancy in the outer region can be accounted for by invoking dark matter; some galaxies require at least four times as much dark matter as luminous matter. There is no evidence for a dependence on galaxy luminosity or morphological type. Various arguments support the idea that a distribution of visible matter with constant M/L is responsible for the circular velocity in the inner region, i.e. inside approximately 2.5 disc scalelengths. Luminous matter and dark matter seem to 'conspire' to produce the flat observed rotation curves in the outer region. It seems unlikely that this coupling between disc and halo results from the large-scale gravitational interaction between the two components. Attempts to determine the shape of dark halos have not yet produced convincing results. (author)

  11. SIGNATURES OF LONG-LIVED SPIRAL PATTERNS

    International Nuclear Information System (INIS)

    Martínez-García, Eric E.; González-Lópezlira, Rosa A.

    2013-01-01

    Azimuthal age/color gradients across spiral arms are a signature of long-lived spirals. From a sample of 19 normal (or weakly barred) spirals where we have previously found azimuthal age/color gradient candidates, 13 objects were further selected if a two-armed grand-design pattern survived in a surface density stellar mass map. Mass maps were obtained from optical and near-infrared imaging, by comparison with a Monte Carlo library of stellar population synthesis models that allowed us to obtain the mass-to-light ratio in the J band, (M/L) J , as a function of (g – i) versus (i – J) color. The selected spirals were analyzed with Fourier methods in search of other signatures of long-lived modes related to the gradients, such as the gradient divergence toward corotation, and the behavior of the phase angle of the two-armed spiral in different wavebands, as expected from theory. The results show additional signatures of long-lived spirals in at least 50% of the objects.

  12. SIGNATURES OF LONG-LIVED SPIRAL PATTERNS

    Energy Technology Data Exchange (ETDEWEB)

    Martinez-Garcia, Eric E. [Instituto Nacional de Astrofisica, Optica y Electronica (INAOE), Aptdo. Postal 51 y 216, 72000 Puebla, Pue. (Mexico); Gonzalez-Lopezlira, Rosa A., E-mail: ericmartinez@inaoep.mx, E-mail: martinez@astro.unam.mx, E-mail: r.gonzalez@crya.unam.mx [Centro de Radioastronomia y Astrofisica, UNAM, Campus Morelia, Michoacan, C.P. 58089 (Mexico)

    2013-03-10

    Azimuthal age/color gradients across spiral arms are a signature of long-lived spirals. From a sample of 19 normal (or weakly barred) spirals where we have previously found azimuthal age/color gradient candidates, 13 objects were further selected if a two-armed grand-design pattern survived in a surface density stellar mass map. Mass maps were obtained from optical and near-infrared imaging, by comparison with a Monte Carlo library of stellar population synthesis models that allowed us to obtain the mass-to-light ratio in the J band, (M/L){sub J}, as a function of (g - i) versus (i - J) color. The selected spirals were analyzed with Fourier methods in search of other signatures of long-lived modes related to the gradients, such as the gradient divergence toward corotation, and the behavior of the phase angle of the two-armed spiral in different wavebands, as expected from theory. The results show additional signatures of long-lived spirals in at least 50% of the objects.

  13. Chiralities of spiral waves and their transitions

    Science.gov (United States)

    Pan, Jun-ting; Cai, Mei-chun; Li, Bing-wei; Zhang, Hong

    2013-06-01

    The chiralities of spiral waves usually refer to their rotation directions (the turning orientations of the spiral temporal movements as time elapses) and their curl directions (the winding orientations of the spiral spatial geometrical structures themselves). Traditionally, they are the same as each other. Namely, they are both clockwise or both counterclockwise. Moreover, the chiralities are determined by the topological charges of spiral waves, and thus they are conserved quantities. After the inwardly propagating spirals were experimentally observed, the relationship between the chiralities and the one between the chiralities and the topological charges are no longer preserved. The chiralities thus become more complex than ever before. As a result, there is now a desire to further study them. In this paper, the chiralities and their transition properties for all kinds of spiral waves are systemically studied in the framework of the complex Ginzburg-Landau equation, and the general relationships both between the chiralities and between the chiralities and the topological charges are obtained. The investigation of some other models, such as the FitzHugh-Nagumo model, the nonuniform Oregonator model, the modified standard model, etc., is also discussed for comparison.

  14. Resistance of full veneer metal crowns with different forms of axial grooves

    Science.gov (United States)

    Hidayat, A. S.; Masulili, C.; Indrasari, M.

    2017-08-01

    Dental crowns or bridges can occasionally come loose or separate from the tooth during chewing, particularly when they are situated on small, short, and conical teeth. The main cause of this separation is a lack of retention and resistance to the tooth. There are several methods available to increase the retention and resistance of the crown during both inlay and onlay preparation, including parallelism, groove preparation, crown build-up, and surface roughness. The aim of this study was to determine the differences in resistance of full veneer metal crowns with various forms of groove preparation. The study involved the compressive strength testing of a total of 24 specimens, namely six specimens without groove preparation, six specimens with box-shaped grooves, six specimens with V-shaped grooves, and six specimens with half round grooves. The mean values of the metal crowns that separated from the teeth during testing were 27.97 ± 1.08 kgF for the crowns with box-shaped grooves, 6.15 ± 0.22 kgF for those with V-shaped grooves, 1.77 ± 0.12 kgF for those with half round grooves, and 0.95 ± 0.13 kgF for those without grooves. This study found that the resistance is best in crowns with box-shaped grooves, followed by those with V-shaped grooves, half round grooves, and those without groove. When clinicians are working on short and conical molar teeth, it is therefore recommended that box-shaped grooves are used to increase the resistance of the crown.

  15. Six Decades of Spiral Density Wave Theory

    Science.gov (United States)

    Shu, Frank H.

    2016-09-01

    The theory of spiral density waves had its origin approximately six decades ago in an attempt to reconcile the winding dilemma of material spiral arms in flattened disk galaxies. We begin with the earliest calculations of linear and nonlinear spiral density waves in disk galaxies, in which the hypothesis of quasi-stationary spiral structure (QSSS) plays a central role. The earliest success was the prediction of the nonlinear compression of the interstellar medium and its embedded magnetic field; the earliest failure, seemingly, was not detecting color gradients associated with the migration of OB stars whose formation is triggered downstream from the spiral shock front. We give the reasons for this apparent failure with an update on the current status of the problem of OB star formation, including its relationship to the feathering substructure of galactic spiral arms. Infrared images can show two-armed, grand design spirals, even when the optical and UV images show flocculent structures. We suggest how the nonlinear response of the interstellar gas, coupled with overlapping subharmonic resonances, might introduce chaotic behavior in the dynamics of the interstellar medium and Population I objects, even though the underlying forces to which they are subject are regular. We then move to a discussion of resonantly forced spiral density waves in a planetary ring and their relationship to the ideas of disk truncation, and the shepherding of narrow rings by satellites orbiting nearby. The back reaction of the rings on the satellites led to the prediction of planet migration in protoplanetary disks, which has had widespread application in the exploding data sets concerning hot Jupiters and extrasolar planetary systems. We then return to the issue of global normal modes in the stellar disk of spiral galaxies and its relationship to the QSSS hypothesis, where the central theoretical concepts involve waves with negative and positive surface densities of energy and angular

  16. Dance, Music, Meter and Groove: A Forgotten Partnership

    Directory of Open Access Journals (Sweden)

    W Tecumseh eFitch

    2016-03-01

    Full Text Available I argue that core aspects of musical rhythm, especially groove and syncopation, can only be fully understood in the context of their origins in the participatory social experience of dance. Musical meter is first considered in the context of bodily movement. I then offer an interpretation of the pervasive but somewhat puzzling phenomenon of syncopation in terms of acoustic emphasis on certain offbeat components of the accompanying dance style. The reasons for the historical tendency of many musical styles to divorce themselves from their dance-based roots are also briefly considered. To the extent that musical rhythms only make sense in the context of bodily movement, researchers interested in ecologically valid approaches to music cognition should make a more concerted effort to extend their analyses to dance, particularly if we hope to understand the cognitive constraints underlying rhythmic aspects of music like meter and groove.

  17. Dance, Music, Meter and Groove: A Forgotten Partnership.

    Science.gov (United States)

    Fitch, W Tecumseh

    2016-01-01

    I argue that core aspects of musical rhythm, especially "groove" and syncopation, can only be fully understood in the context of their origins in the participatory social experience of dance. Musical meter is first considered in the context of bodily movement. I then offer an interpretation of the pervasive but somewhat puzzling phenomenon of syncopation in terms of acoustic emphasis on certain offbeat components of the accompanying dance style. The reasons for the historical tendency of many musical styles to divorce themselves from their dance-based roots are also briefly considered. To the extent that musical rhythms only make sense in the context of bodily movement, researchers interested in ecologically valid approaches to music cognition should make a more concerted effort to extend their analyses to dance, particularly if we hope to understand the cognitive constraints underlying rhythmic aspects of music like meter and groove.

  18. Experimental investigations on an axial grooved cryogenic heat pipe

    Directory of Open Access Journals (Sweden)

    Senthil Kumar Muniappan

    2012-01-01

    Full Text Available This paper deals with development and studies of a trapezoidal axial grooved nitrogen heat pipe. A special liquid nitrogen cryostat has been designed and developed for evaluating the performance of heat pipe where the condenser portion is connected to the cold sink externally. Experiments have been performed on the heat pipe as well as on an equivalent diameter copper rod at different heat loads. The steady state performance of the heat pipe is compared with that of copper rod.

  19. Role of wing morphing in thrust generation

    Directory of Open Access Journals (Sweden)

    Mehdi Ghommem

    2014-01-01

    Full Text Available In this paper, we investigate the role of morphing on flight dynamics of two birds by simulating the flow over rigid and morphing wings that have the characteristics of two different birds, namely the Giant Petrel and Dove Prion. The simulation of a flapping rigid wing shows that the root of the wing should be placed at a specific angle of attack in order to generate enough lift to balance the weight of the bird. However, in this case the generated thrust is either very small, or even negative, depending on the wing shape. Further, results show that morphing of the wing enables a significant increase in the thrust and propulsive efficiency. This indicates that the birds actually utilize some sort of active wing twisting and bending to produce enough thrust. This study should facilitate better guidance for the design of flapping air vehicles.

  20. Axisymmetric thrust-vectoring nozzle performance prediction

    International Nuclear Information System (INIS)

    Wilson, E. A.; Adler, D.; Bar-Yoseph, P.Z

    1998-01-01

    Throat-hinged geometrically variable converging-diverging thrust-vectoring nozzles directly affect the jet flow geometry and rotation angle at the nozzle exit as a function of the nozzle geometry, the nozzle pressure ratio and flight velocity. The consideration of nozzle divergence in the effective-geometric nozzle relation is theoretically considered here for the first time. In this study, an explicit calculation procedure is presented as a function of nozzle geometry at constant nozzle pressure ratio, zero velocity and altitude, and compared with experimental results in a civil thrust-vectoring scenario. This procedure may be used in dynamic thrust-vectoring nozzle design performance predictions or analysis for civil and military nozzles as well as in the definition of initial jet flow conditions in future numerical VSTOL/TV jet performance studies

  1. Quadcopter thrust optimization with ducted-propeller

    Directory of Open Access Journals (Sweden)

    Kuantama Endrowednes

    2017-01-01

    Full Text Available In relation to quadcopter body frame model, propeller can be categorized into propeller with ducted and without ducted. This study present differences between those two using CFD (Computational Fluid Dynamics method. Both categories utilize two blade-propeller with diameter of 406 (mm. Propeller rotation generates acceleration per time unit on the volume of air. Based on the behavior of generated air velocity, ducted propeller can be modeled into three versions. The generated thrust and performance on each model were calculated to determine the best model. The use of ducted propeller increases the total weight of quadcopter and also total thrust. The influence of this modeling were analyzed in detail with variation of angular velocity propeller from 1000 (rpm to 9000 (rpm. Besides the distance between propeller tip and ducted barrier, the size of ducted is also an important part in thrust optimization and total weight minimization of quadcopter.

  2. Thermal Characteristics of Grooved Heat pipe with Hybrid Nanofluids

    Directory of Open Access Journals (Sweden)

    W S Han

    2011-01-01

    Full Text Available In the present study, the specially designed grooved heat pipe charged with nanofluids was investigated in terms of various parameters such as heat transfer rate(50∼300W with 50 W interval, volume concentration(0.005%, 0.05%, 0.1%, and hybrid combinations, inclination(5°, 45°, 90°, cooling water temperature (1℃, 10℃, and 20℃, surface state, transient state and so on. Hybrid nanofluids with different volume concentration ratios with Ag-H2O and Al2O3-H2O were used as working fluids on a grooved heat pipe(GHP. Comparing with the pure water system, nanofluidic and hybrid nanofluidic system shows greater overall thermal resistance with increasing nano-particle concentration. Also hybrid nanofluids make the system deteriorate in terms of thermal resistance. The post nanofluid experimental data regarding GHP show that the heat transfer performance is similar to the results of nanofluid system. The thermal performance of a grooved heat pipe with nanofluids and hybrid nanofluids were varied with driving parameters but they led to worse system performance.

  3. Groove Pancreatitis – A Mimic of Pancreatic and Periampullary Tumors

    Directory of Open Access Journals (Sweden)

    Sivakami R Pradheepkumar

    2017-10-01

    Full Text Available Groove Pancreatitis (GP is a rare form of focal chronic pancreatitis involving the pancreatico-duodenal groove (PDG. GP was first described by Becker in 1973. Though, GP has been described so many years ago, it is still unfamiliar among most physicians because of lack of sufficient case studies and clinical similarity of GP to conventional pancreatitis. Imaging based differentiation of GP from other lesions, like pancreatic and periampullary adenocarcinoma is also not possible in all the cases, unless there are typical findings favoring GP. Since, the line of treatment and outcome is totally different in these two conditions, appreciation of the fine differences between these two entities is very significant. Groove pancreatitis is symptomatically treated with medicines and only for patients with continuous and severe symptoms which are not amenable to medical treatment surgical management is considered. Radiological differentiation of GP from pancreatic and periampullary malignancies will help to avoid unnecessary surgery in the initial stages. We report two cases of GP, one of pure and other of segmental form where we found typical imaging features which pointed to the diagnosis of GP with a small discussion about the Computed tomography (CT and Magnetic Resonance Imaging (MRI appearance of this entity as well as its differential diagnosis.

  4. Plant nuclei can contain extensive grooves and invaginations

    Science.gov (United States)

    Collings, D. A.; Carter, C. N.; Rink, J. C.; Scott, A. C.; Wyatt, S. E.; Allen, N. S.; Brown, C. S. (Principal Investigator)

    2000-01-01

    Plant cells can exhibit highly complex nuclear organization. Through dye-labeling experiments in untransformed onion epidermal and tobacco culture cells and through the expression of green fluorescent protein targeted to either the nucleus or the lumen of the endoplasmic reticulum/nuclear envelope in these cells, we have visualized deep grooves and invaginations into the large nuclei of these cells. In onion, these structures, which are similar to invaginations seen in some animal cells, form tubular or planelike infoldings of the nuclear envelope. Both grooves and invaginations are stable structures, and both have cytoplasmic cores containing actin bundles that can support cytoplasmic streaming. In dividing tobacco cells, invaginations seem to form during cell division, possibly from strands of the endoplasmic reticulum trapped in the reforming nucleus. The substantial increase in nuclear surface area resulting from these grooves and invaginations, their apparent preference for association with nucleoli, and the presence in them of actin bundles that support vesicle motility suggest that the structures might function both in mRNA export from the nucleus and in protein import from the cytoplasm to the nucleus.

  5. Some INDRA experiments on SPIRAL

    International Nuclear Information System (INIS)

    Cussol, D.; Orr, N.A.

    1997-01-01

    A panel joining members of INDRA collaboration and physicists off collaboration was gathered to debate the question whether the INDRA detector, designed to study multifragmentation with beams of stable nuclei, could be used also in experiments with beams of exotic nuclei. Four experiments were discussed as well as the implied detector modifications. In the frame of experiments with SISSI the study of the multifragmentation as a function of N/Z of the system should answer questions related to the system stability as a function of N/Z and origin of the particles emitted during the collision. Among the experiments with SPIRAL to study de-excitation of hot nuclei the following topics were examined: nuclear stability as a function of N/Z, α-n competition, emission of neutron-rich particles as a function of N/Z, evolution of emission modes near the shell closure. The de-excitation of the resonant excited states through 2p decay will be studied in the following three channels: 1p-1p sequential decay, un-correlated simultaneous 2p emission and correlated simultaneous 2p emission ( 2 He emission). Such experiments were carried out on 6 Be, 12 O and 14 O. The only first two channels were observed so far. The 16 Ne could be a good candidate to observe the third channel. Finally sub-barrier Coulomb fusion experiments were also discussed. Concerning the modifications to be undertaken on INDRA detector two were obvious: a modification at the level of electronics to make possible time-of-flight measurements with silicon detectors and transformations of ionization chambers in Bragg chambers. Simulation studies are under way to test the pertinence and validity of the solution

  6. Primary electric propulsion thrust subsystem definition

    Science.gov (United States)

    Masek, T. D.; Ward, J. W.; Kami, S.

    1975-01-01

    A review is presented of the current status of primary propulsion thrust subsystem (TSS) performance, packaging considerations, and certain operational characteristics. Thrust subsystem related work from recent studies by Jet Propulsion Laboratories (JPL), Rockwell and Boeing is discussed. Existing performance for 30-cm thrusters, power processors and TSS is present along with projections for future improvements. Results of analyses to determine (1) magnetic field distributions resulting from an array of thrusters, (2) thruster emitted particle flux distributions from an array of thrusters, and (3) TSS element failure rates are described to indicate the availability of analytical tools for evaluation of TSS designs.

  7. Trochlear groove osteochondritis dissecans of the knee patellofemoral joint.

    Science.gov (United States)

    Wall, Eric J; Heyworth, Benton E; Shea, Kevin G; Edmonds, Eric W; Wright, Rick W; Anderson, Allen F; Eismann, Emily A; Myer, Gregory D

    2014-09-01

    The trochlear groove is the rarest location for osteochondritis dissecans (OCD) of the knee, with only about 50 previously reported cases, most of which were treated before the advent of magnetic resonance imaging (MRI) and modern techniques of cartilage fixation or osteochondral transplantation. The purpose of this multicenter study was to assess the patient presentation and clinical, radiographic, and functional results of treatment for trochlear groove OCD lesions. Hospital records from 5 institutions of the Research in Osteochondritis of the Knee (ROCK) study group were retrospectively reviewed for cases of trochlear groove OCD. Demographics, clinical presentation, diagnosis, treatment, time to pain resolution, and return to sports were recorded. Lesion appearance, size, stability, and time to radiographic healing were evaluated on plain x-rays and MRIs. Trochlear groove OCD lesions were evaluated in 24 knees in 21 adolescents (17 male, 4 female), with an average age of 14 years (range, 10 to 18 y). Fifty-four percent (13/24) of the lesions were identifiable on radiographs, and all were identifiable on MRI, 38% of which (9/24) was unstable. One fourth (6/24) of knees had coexistent femoral condyle OCD lesions. Treatment outcomes were evaluated in patients with a minimum of 1-year follow-up (average: 3 y; range: 1 to 12 y) or healing before 1 year. Half of the knees (2/4) treated nonoperatively and two thirds (8/12) treated operatively showed radiographic signs of healing with patients returning to full activity without pain. Operative treatment success rates were as follows: drilling (3/3), fixation (3/3), microfracture (1/2), drilling with subsequent delayed microfracture (1/1), and drilling with fixation (0/3). MRI aids in the diagnosis and staging of trochlear groove OCD lesions, as almost one half may not be identifiable on radiographs, and one quarter are associated with OCD lesions in other locations of the same knee. Multiple operative treatments can be

  8. Galaxy Zoo: dust in spiral galaxies

    Science.gov (United States)

    Masters, Karen L.; Nichol, Robert; Bamford, Steven; Mosleh, Moein; Lintott, Chris J.; Andreescu, Dan; Edmondson, Edward M.; Keel, William C.; Murray, Phil; Raddick, M. Jordan; Schawinski, Kevin; Slosar, Anže; Szalay, Alexander S.; Thomas, Daniel; Vandenberg, Jan

    2010-05-01

    We investigate the effect of dust on spiral galaxies by measuring the inclination dependence of optical colours for 24276 well-resolved Sloan Digital Sky Survey (SDSS) galaxies visually classified via the Galaxy Zoo project. We find clear trends of reddening with inclination which imply a total extinction from face-on to edge-on of 0.7, 0.6, 0.5 and 0.4mag for the ugri passbands (estimating 0.3mag of extinction in z band). We split the sample into `bulgy' (early-type) and `discy' (late-type) spirals using the SDSS fracdeV (or fDeV) parameter and show that the average face-on colour of `bulgy' spirals is redder than the average edge-on colour of `discy' spirals. This shows that the observed optical colour of a spiral galaxy is determined almost equally by the spiral type (via the bulge-disc ratio and stellar populations), and reddening due to dust. We find that both luminosity and spiral type affect the total amount of extinction, with discy spirals at Mr ~ -21.5mag having the most reddening - more than twice as much as both the lowest luminosity and most massive, bulge-dominated spirals. An increase in dust content is well known for more luminous galaxies, but the decrease of the trend for the most luminous has not been observed before and may be related to their lower levels of recent star formation. We compare our results with the latest dust attenuation models of Tuffs et al. We find that the model reproduces the observed trends reasonably well but overpredicts the amount of u-band attenuation in edge-on galaxies. This could be an inadequacy in the Milky Way extinction law (when applied to external galaxies), but more likely indicates the need for a wider range of dust-star geometries. We end by discussing the effects of dust on large galaxy surveys and emphasize that these effects will become important as we push to higher precision measurements of galaxy properties and their clustering. This publication has been made possible by the participation of more than

  9. CFD investigation of flow and heat transfer of nanofluids in isoflux spirally fluted tubes

    KAUST Repository

    Salama, Amgad

    2012-01-01

    In this work, the problem of flow and heat transfer of nanofluids in spirally fluted tubes is investigated numerically using the CFD code Fluent. The tube investigated in this work is characterized by the existence of helical ridging which is usually obtained by embossing a smooth tube. A tube of diameter of 15 mm, 1.5 mm groove depth and a single helix with pitch of 64 mm is chosen for simulation. This geometry has been chosen for simulation because it has been investigated experimentally for pure fluids and would, therefore, provide a verification framework with our CFD model. The result of our CFD investigation compares very well with the experimental work conducted on this tube geometry. Interesting patterns are highlighted and investigated including the existence of flow swirl as a result of the existence of the spirally enhanced ridges. This swirl flow enhances heat transfer characteristics of this system as reported in the literatures. This study also shows that further enhancement is achieved if small amount of nanoparticles are introduced to the fluid. These nanoparticles (metallic-based nanoparticles) when introduced to the fluid enhances its heat transfer characteristics.

  10. Spiral CT manifestations of spherical pneumonia

    International Nuclear Information System (INIS)

    Li Xiaohong; Yang Hongwei; Xu Chunmin; Qin Xiu

    2008-01-01

    Objective: To explore the Spiral CT manifestations and differential diagnosis of spherical pneumonia. Methods: 18 cases of spherical pneumonia and 20 cases of peripheral pulmonary carcinoma were selected, both of them were confirmed by clinic and/or pathology. The SCT findings of both groups were compared retrospectively. Results: Main spiral CT findings of spherical pneumonia were showed as followings: square or triangular lesions adjacent to pleura; with irregular shape, blurry, slightly lobulated margin, sometimes with halo sign. Small inflammatory patches and intensified vascular markings around the lesions were seen. Lesions became smaller or vanished after short-term anti-inflammatory treatment. Conclusion: Spherical pneumonia showed some characteristics on Spiral CT scan, which are helpful in diagnosis and differential diagnosis of this disease. (authors)

  11. Graphite target for the spiral project

    Energy Technology Data Exchange (ETDEWEB)

    Putaux, J.C.; Ducourtieux, M.; Ferro, A.; Foury, P.; Kotfila, L.; Mueller, A.C.; Obert, J.; Pauwels, N.; Potier, J.C.; Proust, J. [Paris-11 Univ., 91 - Orsay (France). Inst. de Physique Nucleaire; Bertrand, P. [Grand Accelerateur National d`Ions Lourds (GANIL), 14 - Caen (France); Loiselet, M. [Universite Catholique de Louvain, Louvain-La-Neuve (Belgium)] [and others

    1996-12-31

    A study of the thermal and physical properties of graphite targets for the SPIRAL project is presented. The main objective is to develop an optimized set-up both mechanically and thermally resistant, presenting good release properties (hot targets with thin slices). The results of irradiation tests concerning the mechanical and thermal resistance of the first prototype of SPIRAL target with conical geometry are presented. The micro-structural properties of the graphite target is also studied, in order to check that the release properties are not deteriorated by the irradiation. Finally, the results concerning the latest pilot target internally heated by an electrical current are shown. (author). 5 refs.

  12. Photometry and mass modeling of spiral galaxies

    International Nuclear Information System (INIS)

    Kent, S.

    1987-01-01

    Recent estimates of the relative contributions of dark and luminous matter to the mass of spiral galaxies are reviewed. In these studies, the galactic mass distribution is modeled on the basis of photometric and kinematic observational data. The accuracy of current photometry is discussed; the three-dimensional structure of spiral galaxies and the techniques used in bulge-disk decomposition are examined; and mass models incorporating rotation curves are presented. The disk mass/luminosity ratios in the red band (corrected for internal extinction) are found to range from 1.6 to 3.2, with no particular radius at which dark matter dominates. 20 references

  13. Low-Thrust Many-Revolution Trajectory Optimization

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposed research aims to solve the low-thrust many-revolution optimization problem. Optimal low-thrust spaceflight trajectories over hundreds of orbital...

  14. Synthesis and characterization of DNA minor groove binding alkylating agents.

    Science.gov (United States)

    Iyer, Prema; Srinivasan, Ajay; Singh, Sreelekha K; Mascara, Gerard P; Zayitova, Sevara; Sidone, Brian; Fouquerel, Elise; Svilar, David; Sobol, Robert W; Bobola, Michael S; Silber, John R; Gold, Barry

    2013-01-18

    Derivatives of methyl 3-(1-methyl-5-(1-methyl-5-(propylcarbamoyl)-1H-pyrrol-3-ylcarbamoyl)-1H-pyrrol-3-ylamino)-3-oxopropane-1-sulfonate (1), a peptide-based DNA minor groove binding methylating agent, were synthesized and characterized. In all cases, the N-terminus was appended with an O-methyl sulfonate ester, while the C-terminus group was varied with nonpolar and polar side chains. In addition, the number of pyrrole rings was varied from 2 (dipeptide) to 3 (tripeptide). The ability of the different analogues to efficiently generate N3-methyladenine was demonstrated as was their selectivity for minor groove (N3-methyladenine) versus major groove (N7-methylguanine) methylation. Induced circular dichroism studies were used to measure the DNA equilibrium binding properties of the stable sulfone analogues; the tripeptide binds with affinity that is >10-fold higher than that of the dipeptide. The toxicities of the compounds were evaluated in alkA/tag glycosylase mutant E. coli and in human WT glioma cells and in cells overexpressing and under-expressing N-methylpurine-DNA glycosylase, which excises N3-methyladenine from DNA. The results show that equilibrium binding correlates with the levels of N3-methyladenine produced and cellular toxicity. The toxicity of 1 was inversely related to the expression of MPG in both the bacterial and mammalian cell lines. The enhanced toxicity parallels the reduced activation of PARP and the diminished rate of formation of aldehyde reactive sites observed in the MPG knockdown cells. It is proposed that unrepaired N3-methyladenine is toxic due to its ability to directly block DNA polymerization.

  15. Protein-DNA complexation: contact profiles in DNA grooves

    Directory of Open Access Journals (Sweden)

    M. Yu. Zhitnikova

    2017-12-01

    Full Text Available Background: Investigation of the specific protein-DNA complexation mechanisms allows to establish general principles of molecular recognition, which must be taken into account while developing artificial nanostructures based on DNA, and to improve the prediction efficiency of the protein binding sites on DNA. One of the main characteristics of the protein-DNA complexes are the number and type of contacts in the binding sites of DNA and proteins. Conformational changes in the DNA double helix can cause changes in these characteristics. Objectives: The purpose of our study is to establish the features of the interactions between nucleotides and amino acid residues in the binding sites of protein-DNA complexes and their dependence on the conformation of deoxyribose and the angle γ of the polynucleotide chain. Materials and methods: At research of protein-DNA recognition process we have analyzed the contacts between amino acids and nucleotides of the 128 protein-DNA complexes from the structural databases. Conformational parameters of DNA backbone were calculated using the 3DNA/CompDNA program. The number of contacts was determined using a geometric criterion. Two protein and DNA atoms were considered to be in contact if the distance between their centers is less than 4.5 Å. Amino acid residues were arranged according to hydrophobicity scale as hydrophobic or nonpolar and polar. Results: The analysis of contacts between polar and hydrophobic residues and nucleotides with different conformations of the sugar-phosphate backbone showed that nucleotides form more contacts with polar amino acids in both grooves than with hydrophobic ones regardless of nucleotide conformation. But the profile of such contacts differs in minor and major grooves and depends on the conformation of both deoxyribose and γ angle. The contact profiles are characterized by the sequence-specificity or the different propensity of nucleotides to form contacts with the residues in

  16. Revamping Grooving Process for Sustainability using Fuzzy Expert System

    Directory of Open Access Journals (Sweden)

    Iqba Asif

    2016-01-01

    Full Text Available The article presents an application of a fuzzy expert system for renovating a metal cutting process to cope with the sustainability requirements. The work seeks a sustainable balance between energy consumption, productivity and tool damage. Cylindrical grooving experiments were performed to generate data related to quantification of the effects of material hardness, cutting speed, width of cut and feed rate on the aforementioned sustainability measures. A fuzzy knowledge-base was developed that suggests the most suitable adjustments of the controlled variables that would lead to achievement of various combinations of the objectives.

  17. Narrow groove gas metal-arc welding of aluminum

    International Nuclear Information System (INIS)

    Armstrong, R.E.

    1975-01-01

    The Gas Metal-Arc (GMA) welding process is explained and the equipment used described with an analysis of power supply function and the action of the arc, followed by discussion of general applications and problems. GMA braze welding of beryllium is then described, as is the development of a special high purity filler wire and a narrow deep groove joint design for improved weld strength in beryllium. This joint design and the special wire are applied in making high strength welds in high strength aluminum for special applications. High speed motion pictures of the welding operation are shown to illustrate the talk. (auth)

  18. Coronary sinus and atrioventricular groove avulsion after motor vehicle crash

    Directory of Open Access Journals (Sweden)

    Bradley M Dennis

    2014-01-01

    Full Text Available Simultaneous cardiac and pericardial rupture from blunt chest trauma is a highly lethal combination with rarely reported survival. We report of a case of young patient with a right atrioventricular groove injury, pericardial rupture and a unique description of a coronary sinus avulsion following blunt chest trauma. Rapid recognition of this injury is crucial to patient survival, but traditional diagnostic adjuncts such as ultrasound, echocardiography and computed tomography are often unhelpful. Successful repair of these injuries requires high suspicion of injury, early cardiac surgery involvement of and possible even placement of the patient on cardiopulmonary bypass.

  19. A Giant Cavernous Hemangioma of the Left Atrioventricular Groove

    Directory of Open Access Journals (Sweden)

    Chengming Fan

    2017-01-01

    Full Text Available A 10-year-old Chinese female diagnosed with an asymptomatic giant cardiac cavernous hemangioma was reported. The patient originally tended to observation because this unusual cardiac tumoral mass was discovered incidentally during routine health examination of transthoracic echocardiography. Over 5 years of follow-up, the mass had enlarged obviously, and the patient visited our outpatient clinic and was prone to excision. Subsequently, a total resection surgery of the tumor was performed, and the tumor was found to be located on the left atrioventricular groove with complete packing membrane. The patient was discharged on postoperative day 4 and remains asymptomatic on last follow-up.

  20. Optimal Design of Grooved Cam Profile Using Non-uniform Rational B-splines

    Directory of Open Access Journals (Sweden)

    Xuan Guantao

    2017-01-01

    Full Text Available In order to reduce the fatigue damage in grooved cam mechanisms, grooved cam profile was reconstructed with non-uniform rational B-splines (NURBS. Considering joint friction, dynamic model of grooved cam mechanisms was established and the contact stress between grooved cam and follower was calculated using Hertz contact theory. Taking the minimum contact stress and the minimum acceleration as optimal objectives, integrated design model for respective kinematic and dynamic design approaches was set up. The integrated design mode was optimized to search Pareto-optimal solution by an improved artificial fish swarm algorithm, and optimized NURBS profile for grooved cam was acquired. The results show NURBS profile has better kinematic and dynamic performances. The impacts on grooved cam mechanism are reduced and wear characteristics are improved.

  1. Adaptation of the control system in view of SPIRAL integration

    International Nuclear Information System (INIS)

    Lecorche, E.

    1998-01-01

    As soon as the collaboration between the SPIRAL project and the Control Group has been defined, the first implementation of the SPIRAL control system started following various directions. Both the global hardware and software architectures has been specified and some practical works have been undertaken such as the Ethernet network installation or the first SPIRAL oriented software design and coding. (authors)

  2. The dynamics of the spiral galaxy M81

    International Nuclear Information System (INIS)

    Visser, H.C.D.

    1978-01-01

    A detailed comparison of the observations of the spiral galaxy M81 with the density-wave theory for tightly-wound spirals is presented. In particular, hydrogen-line observations are compared with the nonlinear density-wave theory for the gas with the aim of constructing a density-wave model for the spiral galaxy M81

  3. Geometric studies on variable radius spiral cone-beam scanning

    International Nuclear Information System (INIS)

    Ye Yangbo; Zhu Jiehua; Wang Ge

    2004-01-01

    The goal is to perform geometric studies on cone-beam CT scanning along a three-dimensional (3D) spiral of variable radius. First, the background for variable radius spiral cone-beam scanning is given in the context of electron-beam CT/micro-CT. Then, necessary and sufficient conditions are proved for existence and uniqueness of PI lines inside the variable radius 3D spiral. These results are necessary steps toward exact cone-beam reconstruction from a 3D spiral scan of variable radius, adapting Katsevich's formula for the standard helical cone-beam scanning. It is shown in the paper that when the longitudinally projected planar spiral is not always convex toward the origin, the PI line may not be unique in the envelope defined by the tangents of the spiral. This situation can be avoided by using planar spirals whose curvatures are always positive. Using such a spiral, a longitudinally homogeneous region inside the corresponding 3D spiral is constructed in which any point is passed by one and only one PI line, provided the angle ω between planar spiral's tangent and radius is bounded by vertical bar ω-90 deg. vertical bar ≤ε for some positive ε≤32.48 deg. If the radius varies monotonically, this region is larger and one may allow ε≤51.85 deg. Examples for 3D spirals based on logarithmic and Archimedean spirals are given. The corresponding generalized Tam-Danielsson detection windows are also formulated

  4. A nutrient’s downstream spiral

    Science.gov (United States)

    Indicators of a stream’s ability to remove nutrients provide insights on watershed integrity and stream habitat characteristics that are needed to help managers to restore stream ecosystem services. We used the Tracer Additon Spiraling Characterization Curve (TASCC) to mea...

  5. The Distribution of Mass in Spiral Galaxies.

    NARCIS (Netherlands)

    Swaters, Rob; Andersen, David; Bershady, Matthew; Verheijen, Marc

    2002-01-01

    Little is known about the content and distribution of dark matter in spiral galaxies. Mass modeling of any rotation curve can yield an alarming range of results - from entirely halo-dominated, centrally- concentrated dark distributions, to disk-dominated inner potentials with shallow, low density

  6. The surface brightness of spiral galaxies

    International Nuclear Information System (INIS)

    Phillipps, S.; Disney, M.

    1983-01-01

    Correlations between optical surface brightness and the radio properties of spiral galaxies are investigated. It is found that galaxies with high surface brightness are more likely to be strong continuum radio sources and that galaxies with low surface brightness have high 21-cm line emission. (author)

  7. Importance of packing in spiral defect chaos

    Indian Academy of Sciences (India)

    We develop two measures to characterize the geometry of patterns exhibited by the state of spiral defect chaos, a weakly turbulent regime of Rayleigh-Bénard convection. These describe the packing of contiguous stripes within the pattern by quantifying their length and nearest-neighbor distributions. The distributions ...

  8. High-displacement spiral piezoelectric actuators

    Science.gov (United States)

    Mohammadi, F.; Kholkin, A. L.; Jadidian, B.; Safari, A.

    1999-10-01

    A high-displacement piezoelectric actuator, employing spiral geometry of a curved piezoelectric strip is described. The monolithic actuators are fabricated using a layered manufacturing technique, fused deposition of ceramics, which is capable of prototyping electroceramic components with complex shapes. The spiral actuators (2-3 cm in diameter) consisted of 4-5 turns of a lead zirconate titanate ceramic strip with an effective length up to 28 cm. The width was varied from 0.9 to 1.75 mm with a height of 3 mm. When driven by the electric field applied across the width of the spiral wall, the tip of the actuator was found to displace in both radial and tangential directions. The tangential displacement of the tip was about 210 μm under the field of 5 kV/cm. Both the displacement and resonant frequency of the spirals could be tailored by changing the effective length and wall width. The blocking force of the actuator in tangential direction was about 1 N under the field of 5 kV/cm. These properties are advantageous for high-displacement low-force applications where bimorph or monomorph actuators are currently employed.

  9. The Spiral Curriculum. Research into Practice

    Science.gov (United States)

    Johnston, Howard

    2012-01-01

    The Spiral Curriculum is predicated on cognitive theory advanced by Jerome Bruner (1960), who wrote, "We begin with the hypothesis that any subject can be taught in some intellectually honest form to any child at any stage of development." In other words, even the most complex material, if properly structured and presented, can be understood by…

  10. Nobeyama CO Atlas of Nearby Spiral Galaxies

    Science.gov (United States)

    Kuno, N.; Nakai, N.; Sorai, K.; Sato, N..; Yamauchi, A.; Tosaki, T.; Shioya, Y.; Vila-Vilaró, B.; Nishiyama, K.; Ishihara, Y.; Cepa, J.

    BEARS is a 25-beam focal plane array receiver mounted on the Nobeyama 45-m telescope. The combination of the large dish size of the telescope with the excellent performance of this receiver makes it an ideal tool for mapping observations of extended regions of the sky. We present here one of its current applications in a CO mapping survey of nearby spiral galaxies.

  11. A section of a spiral coal chute

    Energy Technology Data Exchange (ETDEWEB)

    Bakhtin, V.N.; Gorodilov, N.N.

    1981-01-01

    A section of a spiral coal chute includes a housing with support brackets. It differs in that to decrease the amount of work necessary for assembly, each support bracket is made with a guide slot and equipped with a pull-out cantilever in the shape of a fork which covers the slot from the lateral sides.

  12. Biofouling of spiral wound membrane systems

    NARCIS (Netherlands)

    Vrouwenvelder, J.S.

    2009-01-01

    Biofouling of spiral wound membrane systems High quality drinking water can be produced with membrane filtration processes like reverse osmosis (RO) and nanofiltration (NF). Because the global demand for fresh clean water is increasing, these membrane technologies will increase in importance in the

  13. SPIRAL2 at GANIL: Status and Perspectives

    Science.gov (United States)

    Gales, S.

    2008-05-01

    To pursue the investigation of a new territory of nuclei with extreme N/Z called ``terra incognita'' several projects, all aiming at the increase by several orders of magnitude of the RIB intensities are now under discussions worldwide. In Europe, two major new projects have been approved recently FAIRatGSI using the so-called ``in-flight'' method and SPIRAL2atGANIL, based on the ISOL method. Both projects were selected in the European Strategic Roadmap For research Infrastructures (ESFRI). The main goal of SPIRAL2 is clearly to extend our knowledge of the limit of existence and the structure of nuclei deeply in the medium and heavy mass region (A = 60 to 140) which is to day an almost unexplored continent. SPIRAL 2 is based on a high power, CW, superconducting driver LINAC, delivering 5 mA of deuteron beams at 40 MeV (200 KW) directed on a C converter+ Uranium target and producing therefore more 1013 fissions/s. The expected radioactive beams intensities for exotic species in the mass range from A = 60 to A = 140, of the order of 106 to 1010 pps will surpass by two order of magnitude any existing facilities in the world. These unstable atoms will be available at energies between few KeV/n to 15 MeV/n. The same driver will accelerate high intensity (100 μA to 1 mA), heavier ions up to Ar at 14 MeV/n producing also proton rich exotic nuclei. In applied areas SPIRAL2 is considered as a powerful variable energy neutron source, a must to study the impact of nuclear fission and fusion on materials. The intensities of these unstable species are excellent opportunities for new tracers and diagnostics either for solid state, material or for radiobiological science and medicine. The ``Go'' decision has been taken in May 2005. The investments and personnel costs amount to 190 M€, for the construction period 2006-2012. Construction of the SPIRAL2 facility is shared by ten French laboratories and a network of international partners. Under the 7FP program of European Union

  14. High temperature thrust chamber for spacecraft

    Science.gov (United States)

    Chazen, Melvin L. (Inventor); Mueller, Thomas J. (Inventor); Kruse, William D. (Inventor)

    1998-01-01

    A high temperature thrust chamber for spacecraft (20) is provided herein. The high temperature thrust chamber comprises a hollow body member (12) having an outer surface and an internal surface (16) defining the high temperature chamber (10). The body member (12) is made substantially of rhenium. An alloy (18) consisting of iridium and at least alloying metal selected of the group consisting of rhodium, platinum and palladium is deposited on at least a portion of the internal surface (16) of the body member (12). The iridium and the alloying metal are electrodeposited onto the body member (12). A HIP cycle is performed upon the body member (12) to cause the coating of iridium and the alloying metal to form the alloy (18) which protects the body member (12) from oxidation.

  15. Midterm results of "thrust plate" prosthesis.

    Science.gov (United States)

    Fink, Bernd; Wessel, Stephanie; Deuretzbacher, Georg; Protzen, Michael; Ruther, Wolfgang

    2007-08-01

    The aim of this investigation was to analyze the midterm results obtained with the metaphyseal fixation principle of the thrust plate prosthesis (TPP). Survival of 214 implants in 204 patients was analyzed. Clinical (Harris hip score) and radiologic examinations were carried out on 157 of 190 TPP with a postimplantation follow-up period of at least 5 years. Failure rate was 7.0% (9 aseptic and 6 septic loosening). Harris hip score increased from 36.9 +/- 13.5 points preoperatively to 91.2 +/- 13.1 points at follow-up. Eleven TPPs showed radiolucent lines not indicating prosthetic loosening. Thrust plate prosthesis is not an alternative to stemmed endoprostheses. It may be rarely indicated in very young patients where, because of their age, several revision operations can be expected.

  16. Low-thrust Isp sensitivity study

    Science.gov (United States)

    Schoenman, L.

    1982-01-01

    A comparison of the cooling requirements and attainable specific impulse performance of engines in the 445 to 4448N thrust class utilizing LOX/RP-1, LOX/Hydrogen and LOX/Methane propellants is presented. The unique design requirements for the regenerative cooling of low-thrust engines operating at high pressures (up to 6894 kPa) were explored analytically by comparing single cooling with the fuel and the oxidizer, and dual cooling with both the fuel and the oxidizer. The effects of coolant channel geometry, chamber length, and contraction ratio on the ability to provide proper cooling were evaluated, as was the resulting specific impulse. The results show that larger contraction ratios and smaller channels are highly desirable for certain propellant combinations.

  17. Advanced tube-bundle rocket thrust chamber

    Science.gov (United States)

    Kazaroff, John M.; Pavli, Albert J.

    1990-01-01

    An advanced rocket thrust chamber for future space application is described along with an improved method of fabrication. Potential benefits of the concept are improved cyclic life, reusability, and performance. Performance improvements are anticipated because of the enhanced heat transfer into the coolant which will enable higher chamber pressure in expander cycle engines. Cyclic life, reusability and reliability improvements are anticipated because of the enhanced structural compliance inherent in the construction. The method of construction involves the forming of the combustion chamber with a tube-bundle of high conductivity copper or copper alloy tubes, and the bonding of these tubes by an electroforming operation. Further, the method of fabrication reduces chamber complexity by incorporating manifolds, jackets, and structural stiffeners while having the potential for thrust chamber cost and weight reduction.

  18. MATERIALS PERFORMANCE TARGETED THRUST FY 2004 PROJECTS

    International Nuclear Information System (INIS)

    DOE

    2005-01-01

    The Yucca Mountain site was recommended by the President to be a geological repository for commercial spent nuclear fuel and high-level radioactive waste. The multi-barrier approach was adopted for assessing and predicting system behavior, including both natural barriers and engineered barriers. A major component of the long-term strategy for safe disposal of nuclear waste is first to completely isolate the radionuclides in waste packages for long times and then to greatly retard the egress and transport of radionuclides from penetrated packages. The goal of the Materials Performance Targeted Thrust program is to further enhance the understanding of the role of engineered barriers in waste isolation. In addition, the Thrust will explore technical enhancements and seek to offer improvements in materials costs and reliability

  19. MATERIALS PERFORMANCE TARGETED THRUST FY 2004 PROJECTS

    Energy Technology Data Exchange (ETDEWEB)

    DOE

    2005-09-13

    The Yucca Mountain site was recommended by the President to be a geological repository for commercial spent nuclear fuel and high-level radioactive waste. The multi-barrier approach was adopted for assessing and predicting system behavior, including both natural barriers and engineered barriers. A major component of the long-term strategy for safe disposal of nuclear waste is first to completely isolate the radionuclides in waste packages for long times and then to greatly retard the egress and transport of radionuclides from penetrated packages. The goal of the Materials Performance Targeted Thrust program is to further enhance the understanding of the role of engineered barriers in waste isolation. In addition, the Thrust will explore technical enhancements and seek to offer improvements in materials costs and reliability.

  20. NATURAL BARRIERS TARGETED THRUST FY 2004 PROJECTS

    International Nuclear Information System (INIS)

    NA

    2005-01-01

    This booklet contains project descriptions of work performed by the Department of Energy (DOE), Office of Civilian Radioactive Waste Management (OCRWM), Office of Science and Technology and International's (OSTandI) Natural Barriers Targeted Thrust during Fiscal Year (FY) 2004. The Natural Barriers Targeted Thrust is part of OSTandI's Science and Technology Program which supports the OCRWM mission to manage and dispose of high-level radioactive waste and spent nuclear fuel in a manner that protects health, safety, and the environment; enhances national and energy security; and merits public confidence. In general, the projects described will continue beyond FY 2004 assuming that the technical work remains relevant to the proposed Yucca Mountain Repository and sufficient funding is made available to the Science and Technology Program

  1. NATURAL BARRIERS TARGETED THRUST FY 2004 PROJECTS

    Energy Technology Data Exchange (ETDEWEB)

    NA

    2005-07-27

    This booklet contains project descriptions of work performed by the Department of Energy (DOE), Office of Civilian Radioactive Waste Management (OCRWM), Office of Science and Technology and International's (OST&I) Natural Barriers Targeted Thrust during Fiscal Year (FY) 2004. The Natural Barriers Targeted Thrust is part of OST&I's Science and Technology Program which supports the OCRWM mission to manage and dispose of high-level radioactive waste and spent nuclear fuel in a manner that protects health, safety, and the environment; enhances national and energy security; and merits public confidence. In general, the projects described will continue beyond FY 2004 assuming that the technical work remains relevant to the proposed Yucca Mountain Repository and sufficient funding is made available to the Science and Technology Program.

  2. Syncopation affects free body-movement in musical groove

    DEFF Research Database (Denmark)

    Witek, Maria A. G.; Popescu, Tudor; Clarke, Eric F

    2016-01-01

    One of the most immediate and overt ways in which people respond to music is by moving their bodies to the beat. However, the extent to which the rhythmic complexity of groove-specifically its syncopation-contributes to how people spontaneously move to music is largely unexplored. Here, we measur...... on the body-part. We demonstrate that while people do not move or synchronise much to rhythms with high syncopation when dancing spontaneously to music, the relationship between rhythmic complexity and synchronisation is less linear than in simple finger-tapping studies.......One of the most immediate and overt ways in which people respond to music is by moving their bodies to the beat. However, the extent to which the rhythmic complexity of groove-specifically its syncopation-contributes to how people spontaneously move to music is largely unexplored. Here, we measured...... free movements in hand and torso while participants listened to drum-breaks with various degrees of syncopation. We found that drum-breaks with medium degrees of syncopation were associated with the same amount of acceleration and synchronisation as low degrees of syncopation. Participants who enjoyed...

  3. Space qualification of high capacity grooved heat pipes

    Energy Technology Data Exchange (ETDEWEB)

    Dubois, M.; Mullender, B.; Druart, J. [SABCA, Societe Anomyme Belgel de Construction Aeronautique (Belgium); Supper, W.; Beddows, A. [ESTEC-The (Netherlands)

    1996-12-31

    Based on the thermal requirements of the future telecommunication satellites, the development of a High Capacity Grooved Heat Pipe (HPG), was contracted by ESA to SABCA leading to an aluminium extruded heat pipe (outer diameter of 25 mm) based on a multi re-entrant grooves design. After an intensive acceptance test campaign whose results showed a good confidence in the design and the fulfillment of the required specifications of heat transport and on tilt capability (experimental maximum heat transport capability of 1500 Watt metres for a vapour temperature of 20 deg C), similar heat pipes have been developed with various outer diameters (11 mm, 15 mm and 20 mm) and with various shapes (circular outer shapes, integrated saddles). Several of these heat pipes were tested during two parabolic flight campaigns, by varying the heat loads during the micro-gravity periods. This HGP heat pipe family is now being submitted to a space qualification program according to ESA standards (ESA PSS-49), both in straight and bent configuration. Within this qualification, the heat pipes are submitted to an extended test campaign including environmental (random/sinus vibration, constant acceleration) and thermal tests (thermal performance, thermal cycle, thermal soak, ageing). (authors) 9 refs.

  4. Nutrient spiraling in streams and river networks

    Science.gov (United States)

    Ensign, Scott H.; Doyle, Martin W.

    2006-12-01

    Over the past 3 decades, nutrient spiraling has become a unifying paradigm for stream biogeochemical research. This paper presents (1) a quantitative synthesis of the nutrient spiraling literature and (2) application of these data to elucidate trends in nutrient spiraling within stream networks. Results are based on 404 individual experiments on ammonium (NH4), nitrate (NO3), and phosphate (PO4) from 52 published studies. Sixty-nine percent of the experiments were performed in first- and second-order streams, and 31% were performed in third- to fifth-order streams. Uptake lengths, Sw, of NH4 (median = 86 m) and PO4 (median = 96 m) were significantly different (α = 0.05) than NO3 (median = 236 m). Areal uptake rates of NH4 (median = 28 μg m-2 min-1) were significantly different than NO3 and PO4 (median = 15 and 14 μg m-2 min-1, respectively). There were significant differences among NH4, NO3, and PO4 uptake velocity (median = 5, 1, and 2 mm min-1, respectively). Correlation analysis results were equivocal on the effect of transient storage on nutrient spiraling. Application of these data to a stream network model showed that recycling (defined here as stream length ÷ Sw) of NH4 and NO3 generally increased with stream order, while PO4 recycling remained constant along a first- to fifth-order stream gradient. Within this hypothetical stream network, cumulative NH4 uptake decreased slightly with stream order, while cumulative NO3 and PO4 uptake increased with stream order. These data suggest the importance of larger rivers to nutrient spiraling and the need to consider how stream networks affect nutrient flux between terrestrial and marine ecosystems.

  5. GANIL-SPIRAL2: A new era

    Science.gov (United States)

    Gales, Sydney

    2011-05-01

    GANIL presently offers unique opportunities in nuclear physics and many other fields that arise from not only the provision of low-energy stable beams, fragmentation beams and re-accelerated radioactive species, but also from the availability of a wide range of state-of-the-art spectrometers and instrumentation. A few examples of recent highlights are discussed in the present paper. With the construction of SPIRAL2 over the next few years, GANIL is in a good position to retain its world-leading capability. As selected by the ESFRI committee, the next generation of ISOL facility in Europe is represented by the SPIRAL2 project to be built at GANIL (Caen, France). SPIRAL 2 is based on a high power, CW, superconducting LINAC, delivering 5 mA of deuteron beams at 40 MeV (200 KW) directed on a C converter+ Uranium target and producing therefore more than 1013 fissions/s. The expected radioactive beam intensities in the mass range from A = 60 to A = 140, will surpass by two orders of magnitude any existing facilities in the world. These unstable atoms will be available at energies between few KeV/n to 15 MeV/n. The same driver will accelerate high intensity (100 μA to 1 mA), heavier ions (Ar up to Xe) at maximum energy of 14 MeV/n. Under the 7FP program of European Union called *Preparatory phase*, the SPIRAL2 project has been granted a budget of about 4M€ to build up an international consortium around this new venture. The status of the construction of SPIRAL2 accelerator and associated physics instruments in collaboration with EU and International partners will be presented.

  6. Geometric tracking control of thrust vectoring UAVs

    OpenAIRE

    Invernizzi, Davide; Lovera, Marco

    2017-01-01

    In this paper a geometric approach to the trajectory tracking control of Unmanned Aerial Vehicles with thrust vectoring capabilities is proposed. The control design is suitable for aerial systems that allow to effectively decouple position and orientation tracking tasks. The control problem is developed within the framework of geometric control theory on the group of rigid displacements SE(3), yielding a control law that is independent of any parametrization of the configuration space. The pr...

  7. THRUST PREDICTION PROGRAM FOR MARINE JET POWER

    OpenAIRE

    Bergsek, Mattias

    2011-01-01

    Marine Jet Power, MJP wishes to investigate the possibility of transforming their current Thrust Prediction Program, TPP written in C++ source code into a more up to date tool for their sales staff. The old TPP, though an accurate and precise tool, is not documented and lacks commentaries in the source code. Therefore the beginning of this master thesis was about documenting and investigates what methods were used to calculate the performance of the water jet system.The next step was splittin...

  8. Thermal effects in an accelerating thrust bearing

    Science.gov (United States)

    Doo, R.; Rodkiewicz, C. M.; Gupta, R. N.

    1985-01-01

    This study is mainly concerned with the development of transient temperatures in a thrust bearing. The effect of Prandtl number on temperatures was also investigated. All lubricant properties were assumed to be constant. It was found that the location of highest temperatures depended on the bearing ratio. The effect of Prandtl number on temperatures was small. However, its effect on the heat transfer at the surfaces was significant.

  9. Experimental performance of 75-millimeter-bore arched outer-race ball bearings to 2.1 million DN. [thrust loads

    Science.gov (United States)

    Coe, H. H.

    1976-01-01

    An experimental investigation was performed to determine the operating characteristics of arched outer-race bearings and to compare the data with those for a similar, but conventional, deep-groove ball bearing. The bearings were tested over a range of shaft speeds up to 28,000 rpm at a thrust load of 2200 newtons (500 lb). One bearing was operated at 26,000 rpm with a range of thrust loads. The amounts of arching were 0.13, 0.25, and 0.51 millimeter (0.005, 0.010, and 0.020 in.). All bearings operated satisfactorily; the arched bearing outer-race temperatures and torques were consistently higher than those for the conventional bearing.

  10. Several topics on orbital dynamics of consecutive, low-thrust, accelerated spacecraft trajectories

    OpenAIRE

    Yamakawa, Hiroshi; 山川 宏

    2008-01-01

    Orbital dynamics of consecutive, low-thrust trajectories is overviewed. Focusing on the thrust direction constraints (e.g., transversal and radial thrust direction constraints), various trajectory design strategies of low-thrust missions are summarized with concrete examples.

  11. Aircraft Engine Thrust Estimator Design Based on GSA-LSSVM

    Science.gov (United States)

    Sheng, Hanlin; Zhang, Tianhong

    2017-08-01

    In view of the necessity of highly precise and reliable thrust estimator to achieve direct thrust control of aircraft engine, based on support vector regression (SVR), as well as least square support vector machine (LSSVM) and a new optimization algorithm - gravitational search algorithm (GSA), by performing integrated modelling and parameter optimization, a GSA-LSSVM-based thrust estimator design solution is proposed. The results show that compared to particle swarm optimization (PSO) algorithm, GSA can find unknown optimization parameter better and enables the model developed with better prediction and generalization ability. The model can better predict aircraft engine thrust and thus fulfills the need of direct thrust control of aircraft engine.

  12. Conjunction challenges of low-thrust geosynchronous debris removal maneuvers

    Science.gov (United States)

    Anderson, Paul V.; Schaub, Hanspeter

    2016-06-01

    The conjunction challenges of low-thrust engines for continuous thrust re-orbiting of geosynchronous (GEO) objects to super-synchronous disposal orbits are investigated, with applications to end-of-life mitigation and active debris removal (ADR) technologies. In particular, the low maneuverability of low-thrust systems renders collision avoidance a challenging task. This study investigates the number of conjunction events a low-thrust system could encounter with the current GEO debris population during a typical re-orbit to 300 km above the GEO ring. Sensitivities to thrust level and initial longitude and inclination are evaluated, and the impact of delaying the start time for a re-orbiting maneuver is assessed. Results demonstrate that the mean number of conjunctions increases hyperbolically as thrust level decreases, but timing the start of the maneuver appropriately can reduce the average conjunction rate when lower thrust levels are applied.

  13. Spiral analysis-improved clinical utility with center detection.

    Science.gov (United States)

    Wang, Hongzhi; Yu, Qiping; Kurtis, Mónica M; Floyd, Alicia G; Smith, Whitney A; Pullman, Seth L

    2008-06-30

    Spiral analysis is a computerized method that measures human motor performance from handwritten Archimedean spirals. It quantifies normal motor activity, and detects early disease as well as dysfunction in patients with movement disorders. The clinical utility of spiral analysis is based on kinematic and dynamic indices derived from the original spiral trace, which must be detected and transformed into mathematical expressions with great precision. Accurately determining the center of the spiral and reducing spurious low frequency noise caused by center selection error is important to the analysis. Handwritten spirals do not all start at the same point, even when marked on paper, and drawing artifacts are not easily filtered without distortion of the spiral data and corruption of the performance indices. In this report, we describe a method for detecting the optimal spiral center and reducing the unwanted drawing artifacts. To demonstrate overall improvement to spiral analysis, we study the impact of the optimal spiral center detection in different frequency domains separately and find that it notably improves the clinical spiral measurement accuracy in low frequency domains.

  14. Prevalence of palate-gingival groove in patients of Dhulikhel Hospital

    Directory of Open Access Journals (Sweden)

    D Shreshta

    2015-06-01

    Full Text Available Background: Palato-gingival groove is a rare developmental anomaly leading to pulpal and periodontal diseases. Radicular extensions of these grooves are areas for plaque accumulation which are difficult to clean. Its clinical and radiographic findings mimic endo-perio lesions leading to diagnostic dilemma, ineffective treatment attempts and treatment failures. Objectives: To investigate the prevalence of coronal and radicular palato-gingival groove in dental patients visiting Dhulikhel Hospital and its association with gingival disease. Methods: Patients (N=231 visiting dental out-patient department of Dhulikhel Hospital, were examined for the presence or absence of palato-gingival groove in maxillary anteriors. Loe and Silness Gingival index was also recorded for all the patients using University of North Caroline-15 periodontal probe. Chisquare test was used to test the association of the presence of palato-gingival groove and gingival disease. P value of <0.05 was considered to be significant. Results: A total of 1362 maxillary anterior teeth were included in the study. The prevalence of coronal palatogingival groove among 1362 teeth was 6.6%. Coronal palato-gingival grooves were more common in females (56.6% than in male (43.3% patients. Prevalence of radicular groove was only 0.88% for lateral incisors and 0.2% for canines. There was no significant association between palate-gingival groove and gingival disease (P=0.91. Conclusion: The prevalence of palato-gingival groove is common in dental patients visiting Dhulikhel Hospital. Gingival disease is not significantly associated with palate-gingival groove. DOI: http://dx.doi.org/10.3126/jcmsn.v10i1.12765 Journal of College of Medical Sciences-Nepal, 2014, Vol.10(1; 32-36

  15. From old alkylating agents to new minor groove binders.

    Science.gov (United States)

    Puyo, Stéphane; Montaudon, Danièle; Pourquier, Philippe

    2014-01-01

    Alkylating agents represent the oldest class of anticancer agents with the approval of mechloretamine by the FDA in 1949. Even though their clinical use is far beyond the use of new targeted therapies, they still occupy a major place in the treatment of specific malignancies, sometimes representing the unique option for the treatment of refractory tumors. Here, we are reviewing the major classes of alkylating agents, with a particular focus on the latest generations of compounds that specifically target the minor groove of the DNA. These naturally occurring derivatives have a unique mechanism of action that explains the recent regain of interest in developing new classes of alkylating agents that could be used in combination with other anticancer drugs to enhance tumor response in the clinic. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

  16. Dance, Music, Meter and Groove: A Forgotten Partnership

    Science.gov (United States)

    Fitch, W. Tecumseh

    2016-01-01

    I argue that core aspects of musical rhythm, especially “groove” and syncopation, can only be fully understood in the context of their origins in the participatory social experience of dance. Musical meter is first considered in the context of bodily movement. I then offer an interpretation of the pervasive but somewhat puzzling phenomenon of syncopation in terms of acoustic emphasis on certain offbeat components of the accompanying dance style. The reasons for the historical tendency of many musical styles to divorce themselves from their dance-based roots are also briefly considered. To the extent that musical rhythms only make sense in the context of bodily movement, researchers interested in ecologically valid approaches to music cognition should make a more concerted effort to extend their analyses to dance, particularly if we hope to understand the cognitive constraints underlying rhythmic aspects of music like meter and groove. PMID:26973489

  17. Hybrid plasmonic waveguide in a metal V-groove

    Directory of Open Access Journals (Sweden)

    Zhao-xian Chen

    2014-01-01

    Full Text Available We propose and investigate a type of hybrid plasmonic waveguide in a metal V-groove. A high-permittivity nanowire was placed in the metal channel covered with a dielectric film of lower permittivity. Deeper sub-wavelength confinement and much longer propagation distance were achieved in comparison with conventional channel plasmonic waveguides. The overall performance was improved as compared with the conventional hybrid plasmonic structure based on a flat metal surface. Finite element analysis showed that both the mode propagation and field profile can be adjusted by changing the nanowire radius and film thickness. Some benefits, such as a reduced scattering loss caused by the surface roughness, are also expected owing to the unique mode profile. The proposed approach has potential for application in high-level photonic integration.

  18. Simulations of axial B-dot monitors inside a groove in the beam pipe

    Energy Technology Data Exchange (ETDEWEB)

    He, Xiaozhong, E-mail: hexiaozhong@tsinghua.org.cn [Institute of Fluid Physics, Chinese Academy of Engineering Physics, Mianyang, Sichuan (China); Pang, Jian; Li, Qin [Institute of Fluid Physics, Chinese Academy of Engineering Physics, Mianyang, Sichuan (China); Du, Yingchao [Department of Engineering Physics, Tsinghua University, Beijing (China)

    2013-11-21

    Beam tilt measurement is important for understanding the beam dynamics. Our previous theoretical studies and simulations have shown that the axial B-dot in smooth beam pipe can be used to measure the beam tilt directly. Practical azimuthal B-dot loops typically are placed inside a groove in the beam pipe to avoid direct beam interception. For the same purpose, practical axial B-dot loops should also be placed inside such a groove. In this paper, responses of axial magnetic field to the beam tilt and to the beam offset, in the presence of the groove, are investigated by simulations. The simulation results show that the axial magnetic field in the central plane of the groove is proportional to the beam tilt and independent on the centroid position. The ratio between the axial magnetic field and the beam tilt depends on the position of the axial B-dot loop and the dimensions of the groove. -- Highlights: •MAFIA simulations were carried out to analyze the influence of recessed groove to axial B dots. •It is found that axial B dots still works in the central plane of the recessed groove. •The dimensions of the groove greatly influence the signal strength of axial B dots. •Results can be used for future optimizations.

  19. Effect of pass schedule and groove design on the metal deformation ...

    Indian Academy of Sciences (India)

    minimise fish tail losses. The surface quality is improved by the ability to avoid fin formation that occurs at certain conditions of rolling. Thus, the groove geometry, roll pass schedule and rolling mill parameters and temperature can be optimised for best product quality and yield. Keywords. Hot rolling; groove geometry; pass ...

  20. Gradient ROtating Outer Volume Excitation (GROOVE): A Novel Method for Single-Shot 2-D OVS

    Science.gov (United States)

    Powell, Nathaniel J.; Jang, Albert; Park, Jang-Yeon; Valette, Julien; Garwood, Michael; Marjańska, Małgorzata

    2014-01-01

    Purpose A new outer volume suppression (OVS) technique is introduced that uses a single pulse and rotating gradients to accomplish frequency-swept excitation. This new technique, which is called Gradient ROtating Outer Volume Excitation (GROOVE), produces a circular or elliptical suppression band rather than suppressing the entire outer volume. Methods Theoretical and k-space descriptions of GROOVE are provided. The properties of GROOVE were investigated with simulations, phantom, and human experiments performed using a 4 T horizontal bore magnet equipped with a TEM coil. Results Similar suppression performance was obtained in phantom and human brain using GROOVE with circular and elliptical shapes. Simulations indicate that GROOVE requires less SAR and time than traditional OVS schemes, but traditional schemes provide a sharper transition zone and less residual signal. Conclusion GROOVE represents a new way of performing OVS in which spins are excited temporally in space on a trajectory which can be tailored to fit the shape of the suppression region. In addition, GROOVE is capable of suppressing tailored regions of space with more flexibility and in a shorter period of time than conventional methods. GROOVE provides a fast, low SAR alternative to conventional OVS methods in some applications (e.g., scalp suppression). PMID:24478130

  1. Fast spiral-scan atomic force microscopy

    International Nuclear Information System (INIS)

    Mahmood, I A; Reza Moheimani, S O

    2009-01-01

    In this paper, we describe a new scanning technique for fast atomic force microscopy. In this method, the sample is scanned in a spiral pattern instead of the well established raster pattern. A spiral scan can be produced by applying single frequency cosine and sine signals with slowly varying amplitudes to the x-axis and y-axis of an atomic force microscope (AFM) scanner respectively. The use of the single tone input signals allows the scanner to move at high speeds without exciting the mechanical resonance of the device and with relatively small control efforts. Experimental results obtained by implementing this technique on a commercial AFM indicate that high-quality images can be generated at scan frequencies well beyond the raster scans.

  2. Spiral optical designs for nonimaging applications

    Science.gov (United States)

    Zamora, Pablo; Benítez, Pablo; Miñano, Juan C.; Vilaplana, Juan; Buljan, Marina

    2011-10-01

    Manufacturing technologies as injection molding or embossing specify their production limits for minimum radii of the vertices or draft angle for demolding, for instance. In some demanding nonimaging applications, these restrictions may limit the system optical efficiency or affect the generation of undesired artifacts on the illumination pattern. A novel manufacturing concept is presented here, in which the optical surfaces are not obtained from the usual revolution symmetry with respect to a central axis (z axis), but they are calculated as free-form surfaces describing a spiral trajectory around z axis. The main advantage of this new concept lies in the manufacturing process: a molded piece can be easily separated from its mold just by applying a combination of rotational movement around axis z and linear movement along axis z, even for negative draft angles. Some of these spiral symmetry examples will be shown here, as well as their simulated results.

  3. Star distribution in the Orion spiral arm

    International Nuclear Information System (INIS)

    Basharina, T.S.; Pavlovskaya, E.D.; Filippova, A.A.

    1985-01-01

    The structure of the Orion spiral arm is studied by numerical experiments, assuming that in each direction considered the star distribution along the line of sight is a combination of two Gaussian laws. The corresponding parameters are evaluated for four Milky Way fields; the bimodal laws now fit the observations by the chi 2 criterion. In the Orion arm the line-of-sight star densities follow asymmetric curves, steeper at the outer edge of the arm

  4. Dark and visible matter in spiral galaxies

    International Nuclear Information System (INIS)

    Persic, M.; Salucci, P.; Durham Univ.

    1988-01-01

    Exploiting relevant information from the profiles of rotation curves, we calculate the dark-to-luminous mass ratio within the disc size for a sample of 43 spiral galaxies. The values we find, while proving the ubiquitous presence of dark matter, vary with luminosity. Faint and bright galaxies are found to be respectively halo- and disc-dominated in the disc regions. The luminosity sequence turns out to be a dark-to-luminous sequence. (author)

  5. The surface brightness of spiral galaxies

    International Nuclear Information System (INIS)

    Phillipps, S.; Disney, M.

    1983-01-01

    It is proposed that Freeman's discovery that the extrapolated central surface brightness of spiral galaxies is approximately constant can be simply explained if the galaxies contain a spheroidal component which dominates the light in their outer isophotes. Calculations of an effective central surface brightness indicate a wide spread of values. This requires either a wide spread in disc properties or significant spheroidal components or, most probably, both. (author)

  6. Treatment of a Developmental Groove and Supernumerary Root Using Guided Tissue Regeneration Technique

    Directory of Open Access Journals (Sweden)

    Zahra Alizadeh Tabari

    2016-01-01

    Full Text Available Introduction. The radicular groove is a developmental groove which is usually found on the palatal or lateral aspects of the maxillary incisor teeth. The present case is a maxillary lateral incisor with a small second root and a deep radicular groove. The developmental groove caused a combined periodontal-endodontic lesion. Methods. Case was managed using a combined treatment procedure involving nonsurgical root canal therapy and surgical periodontal treatment. After completion of root canal treatment, guided tissue regeneration (GTR was carried out using decalcified freeze dried bone allograft (DFDBA and a bioabsorbable collagenous membrane. Tooth also was splinted for two months. Results. After 12 months the tooth was asymptomatic. The periapical radiolucency disappeared and probing depth did not exceed 3 mm. Conclusion. Combined treatment procedure involving nonsurgical root canal therapy and surgical periodontal regenerative treatment can be a predictable technique in treating combined endodontic-periodontal lesions caused by radicular groove.

  7. Dispersion characteristics of planar grating with arbitrary grooves for terahertz Smith-Purcell radiation

    International Nuclear Information System (INIS)

    Cao, Miaomiao; Li, Ke; Liu, Wenxin; Wang, Yong

    2015-01-01

    In this paper, a novel method of getting the dispersion relations in planar grating with arbitrary grooves for terahertz Smith-Purcell radiation is investigated analytically. The continuous profile of the groove is approximately replaced by a series of rectangular steps. By making use of field matches method and the continuity of transverse admittance, the universal dispersion equation for grating with arbitrarily shaped grooves is derived. By solving the dispersion equation in presence of electron beam, the growth rate is obtained directly and the dependence on beam parameters is analyzed. Comparisons of the dispersion characteristics among some special groove shapes have been made by numerical calculation. The results show that the rectangular-step approximation method provides a novel approach to obtain the universal dispersion relation for grating with arbitrary grooves for Smith-Purcell radiation

  8. Source-model technique analysis of electromagnetic scattering by surface grooves and slits.

    Science.gov (United States)

    Trotskovsky, Konstantin; Leviatan, Yehuda

    2011-04-01

    A computational tool, based on the source-model technique (SMT), for analysis of electromagnetic wave scattering by surface grooves and slits is presented. The idea is to use a superposition of the solution of the unperturbed problem and local corrections in the groove/slit region (the grooves and slits are treated as perturbations). In this manner, the solution is obtained in a much faster way than solving the original problem. The proposed solution is applied to problems of grooves and slits in otherwise planar or periodic surfaces. Grooves and slits of various shapes, both smooth ones as well as ones with edges, empty or filled with dielectric material, are considered. The obtained results are verified against previously published data. © 2011 Optical Society of America

  9. Spiral-arm instability: giant clump formation via fragmentation of a galactic spiral arm

    Science.gov (United States)

    Inoue, Shigeki; Yoshida, Naoki

    2018-03-01

    Fragmentation of a spiral arm is thought to drive the formation of giant clumps in galaxies. Using linear perturbation analysis for self-gravitating spiral arms, we derive an instability parameter and define the conditions for clump formation. We extend our analysis to multicomponent systems that consist of gas and stars in an external potential. We then perform numerical simulations of isolated disc galaxies with isothermal gas, and compare the results with the prediction of our analytic model. Our model describes accurately the evolution of the spiral arms in our simulations, even when spiral arms dynamically interact with one another. We show that most of the giant clumps formed in the simulated disc galaxies satisfy the instability condition. The clump masses predicted by our model are in agreement with the simulation results, but the growth time-scale of unstable perturbations is overestimated by a factor of a few. We also apply our instability analysis to derive scaling relations of clump properties. The expected scaling relation between the clump size, velocity dispersion, and circular velocity is slightly different from that given by the Toomre instability analyses, but neither is inconsistent with currently available observations. We argue that the spiral-arm instability is a viable formation mechanism of giant clumps in gas-rich disc galaxies.

  10. Incorporating hydrologic variability into nutrient spiraling

    Science.gov (United States)

    Doyle, Martin W.

    2005-09-01

    Nutrient spiraling describes the path of a nutrient molecule within a stream ecosystem, combining the biochemical cycling processes with the downstream driving force of stream discharge. To date, nutrient spiraling approaches have been hampered by their inability to deal with fluctuating flows, as most studies have characterized nutrient retention within only a small range of discharges near base flow. Here hydrologic variability is incorporated into nutrient spiraling theory by drawing on the fluvial geomorphic concept of effective discharge. The effective discharge for nutrient retention is proposed to be that discharge which, over long periods of time, is responsible for the greatest portion of nutrient retention. A developed analytical model predicts that the effective discharge for nutrient retention will equal the modal discharge for small streams or those with little discharge variability. As modal discharge increases or discharge variability increases, the effective discharge becomes increasingly less than the modal discharge. In addition to the effective discharge, a new metric is proposed, the functionally equivalent discharge, which is the single discharge that will reproduce the magnitude of nutrient retention generated by the full hydrologic frequency distribution when all discharge takes place at that rate. The functionally equivalent discharge was found to be the same as the modal discharge at low hydrologic variability, but increasingly different from the modal discharge at large hydrologic variability. The functionally equivalent discharge provides a simple quantitative means of incorporating hydrologic variability into long-term nutrient budgets.

  11. Low-thrust roundtrip trajectories to Mars with one-synodic-period repeat time

    Science.gov (United States)

    Okutsu, Masataka; Landau, Damon F.; Rogers, Blake A.; Longuski, James M.

    2015-05-01

    Cycler trajectories-both ballistic and powered-are reported in the literature in which there are two-vehicle, three-vehicle, and four-vehicle cases. Such trajectories permit the installation of cycler vehicles which provide safe and comfortable living conditions for human space travel between Earth and Mars during every synodic opportunity. The question the present paper answers is a logical, obvious one: Does a single-vehicle, one-synodic-period cycler exist? The answer is yes: such a trajectory can be flown-but only with a high-power electric propulsion system. In our example, it is found that "stopover" trajectories that spend 30 days in orbit about Earth and 30 days about Mars, and return astronauts to Earth in one synodic period require a 90-t power generator with a power level of 11 MWe. Fortuitously, and in lieu of using chemical propulsion, the high power level of the electric propulsion system would also be effective in hauling the cargo payload via a spiral trajectory about the Earth. But because one synodic period is not enough for the cycler vehicle to fly both the interplanetary trajectories and the Earth-spiral trajectories, we suggest developing two nuclear power generators, which could alternate flying the interplanetary trajectories and the Earth-spiral trajectories. Once these power generators are launched and begin operating in space, the mass requirement in seven subsequent missions (over a period of 15 years beginning in 2022) would be modest at 250-300 metric tons to low-Earth orbit per mission. Thus two cargo launches of NASA's Space Launch System and one crew launch of the Falcon Heavy, for example, would be adequate to maintain support for each consecutive mission. Although we propose developing two sets of electric propulsion systems to account for the Earth-spiral phases, only one vehicle is flown on a heliocentric trajectory at any given time. Thus, our low-thrust stopover cycler with zero encounter velocities falls into a category of a

  12. Individual differences in beat perception affect gait responses to low- and high-groove music.

    Directory of Open Access Journals (Sweden)

    Li-Ann eLeow

    2014-10-01

    Full Text Available Slowed gait in Parkinson’s disease (PD patients can be improved when patients synchronize footsteps to isochronous metronome cues, but limited retention of such improvements suggest that permanent cueing regimes are needed for long-term improvements. If so, music might make permanent cueing regimes more pleasant, improving adherence; however, music cueing requires patients to synchronize movements to the beat, which might be difficult for PD patients who tend to show weak beat perception. One solution may be to use high groove music, which has high beat salience that may facilitate synchronization, and affective properties which may improve motivation to move. As a first step in understanding how beat perception affects gait in complex neurological disorders, we examined how beat perception ability affected gait in neurotypical adults. Synchronization performance and gait parameters were assessed as healthy young adults with strong or weak beat perception synchronized to low groove music, high groove music, and metronome cues. High groove music was predicted to elicit better synchronization than low groove music, due to its higher beat salience. Two musical tempi, or rates, were used: (1 preferred tempo: beat rate matched to preferred step rate and (2 faster tempo: beat rate adjusted to 22.5% faster than preferred step rate. For both strong and weak beat-perceivers, synchronization performance was best with metronome cues, followed by high groove music, and worst with low groove music. In addition, high groove music elicited longer and faster steps than low groove music, both at preferred tempo and at faster tempo. Low groove music was particularly detrimental to gait in weak beat-perceivers, who showed slower and shorter steps compared to uncued walking. The findings show that individual differences in beat perception affect gait when synchronizing footsteps to music, and have implications for using music in gait rehabilitation.

  13. Determination of Tongue and Groove parameters for multileaf collimators; Determinaco de parametros de Tongue and Groove de colimadores de multilaminas

    Energy Technology Data Exchange (ETDEWEB)

    Castro, Aluisio; Almeida, Carlos E. de, E-mail: alu_neto@hotmail.com [Universidade Estadual do Rio de Janeiro (UERJ), RJ (Brazil). Laboratorio de Ciencias Radiologicas; Nguyen, Bihn [Prowess Inc., Concord, CA (United States)

    2012-08-15

    The Tongue and Groove effect (TandG) is characterized by an additional attenuation between adjacent and opposing leaves on multileaf collimators (MLCs) in adjacent or complementary fields. This is a typical situation in of intensity-modulated radiotherapy treatments. The aim of this study was to measure the width and transmission of TandG effect for two commercial MLCs: Varian Millennium 120 (6 MV and 16 MV beams) and BrainLab m3 (only for 6 MV). The methodology used was based on the creation of MLC shapes that emphasizes TandG effect, the irradiation of these fields on radiochromic film and the sensitometric evaluation of the films in order to determine the TandG width and transmission. The results for TandG width for studied MLCs were 2.5, 1.8 and 2 mm, respectively, whit transmission TandG values of 87, 90 and 85%. (author)

  14. Ear-body lift and a novel thrust generating mechanism revealed by the complex wake of brown long-eared bats (Plecotus auritus)

    DEFF Research Database (Denmark)

    Johansson, L Christoffer; Håkansson, Jonas; Jakobsen, Lasse

    2016-01-01

    Large ears enhance perception of echolocation and prey generated sounds in bats. However, external ears likely impair aerodynamic performance of bats compared to birds. But large ears may generate lift on their own, mitigating the negative effects. We studied flying brown long-eared bats, using....... We also propose that the bats use a novel wing pitch mechanism at the end of the upstroke generating thrust at low speeds, which should provide effective pitch and yaw control. In addition, the wing tip vortices show a distinct spiraling pattern. The tip vortex of the previous wingbeat remains...... into the next wingbeat and rotates together with a newly formed tip vortex. Several smaller vortices, related to changes in circulation around the wing also spiral the tip vortex. Our results thus show a new level of complexity in bat wakes and suggest large eared bats are less aerodynamically limited than...

  15. A Low Friction Thrust Bearing for Reciprocating Compressors

    OpenAIRE

    Nagata, Shuhei; Kousokabe, Hirokatsu; Sekiyama, Nobuya; Ono, Toshiaki

    2012-01-01

    A thrust bearing with a micro texture on its sliding surface that produces hydrodynamic pressure was developed for use in reciprocating compressors. Evaluation using an elemental friction test showed that its friction loss was 20–60 % lower than that of the current design. Measurement of the efficiency of a compressor with the developed thrust bearing showed that the coefficient of performance was 1.4 % higher than that of a compressor with a conventional thrust bearing.

  16. Design and test of a magnetic thrust bearing

    Science.gov (United States)

    Allaire, P. E.; Mikula, A.; Banerjee, B.; Lewis, D. W.; Imlach, J.

    1993-01-01

    A magnetic thrust bearing can be employed to take thrust loads in rotating machinery. The design and construction of a prototype magnetic thrust bearing for a high load per weight application is described. The theory for the bearing is developed. Fixtures were designed and the bearing was tested for load capacity using a universal testing machine. Various shims were employed to have known gap thicknesses. A comparison of the theory and measured results is presented.

  17. Antennal sensilla of female Encarsia guadeloupae Viggiani (Hymenoptera: Aphelinidae), a nymphal parasitoid of the spiraling whitefly Aleurodicus dispersus (Hemiptera: Aleyrodidae).

    Science.gov (United States)

    Zhou, Hui; Wu, Wei-Jian; Niu, Li-Ming; Fu, Yue-Guan

    2013-01-01

    Encarsia guadeloupae Viggiani (Hymenoptera: Aphelinidae) is a minute, obligate endoparasitoid against the spiraling whitefly Aleurodicus dispersus nymph. The external morphology and distribution of the antennal sensilla of female E. guadeloupae were observed by scanning electron microscopy. Antennae of female E. guadeloupae were geniculate in shape, which consist of scape with a radicula, pedicel, and flagellum. Eight morphological sensilla types were recorded in the females: nonporous sensilla chaetica (CH-NP) and nonporous sensilla trichodea (ST-NP); uniporous sensilla chaetica (CH-UP) and uniporous sensilla trichodea (ST-UP) with a tip pore, basiconic capitate peg sensilla with numerous pores open at the bottom of the grooves; multiporous sensilla placoid (MSP) with the multiporous cuticular structure; uniporous rod-like sensilla (RO-UP) with robust grooved surfaces and the tremendous apical hole; nonporous finger-like sensilla (FI-NP) with abundant pimples at the bulgy, mortar-shaped short stalk. In order to further explore the host location mechanisms and courtship behavior of E. guadeloupae, the possible roles of the antennal sensilla of this species were discussed. Copyright © 2012 Elsevier Ltd. All rights reserved.

  18. Ablation acceleration of macroparticle in spiral magnetic fields

    International Nuclear Information System (INIS)

    Ikuta, Kazunari.

    1981-05-01

    The rocket motion of macroparticles heated by energetic pulses in a spiral magnetic field was studied. The purpose of the present work is to study the ablation acceleration of a macroparticle in a spiral magnetic field with the help of the law of conservation of angular momentum. The basic equation of motion of ablatively accelerated projectile in a spiral magnetic field was derived. Any rocket which is ejecting fully ionized plasma in an intense magnetic field with rotational transform is able to have spin by the law of conservation of momentum. The effect of spiral magnetic field on macroparticle acceleration is discussed. The necessary mass ratio increase exponentially with respect to the field parameter. The spiral field should be employed with care to have only to stabilize the position of macroparticles. As conclusion, it can be said that the ablation acceleration of the projectile in a spiral field can give the accelerated body spin quite easily. (Kato, T.)

  19. Mechanical response of spiral interconnect arrays for highly stretchable electronics

    KAUST Repository

    Qaiser, Nadeem

    2017-11-21

    A spiral interconnect array is a commonly used architecture for stretchable electronics, which accommodates large deformations during stretching. Here, we show the effect of different geometrical morphologies on the deformation behavior of the spiral island network. We use numerical modeling to calculate the stresses and strains in the spiral interconnects under the prescribed displacement of 1000 μm. Our result shows that spiral arm elongation depends on the angular position of that particular spiral in the array. We also introduce the concept of a unit-cell, which fairly replicates the deformation mechanism for full complex hexagon, diamond, and square shaped arrays. The spiral interconnects which are axially connected between displaced and fixed islands attain higher stretchability and thus experience the maximum deformations. We perform tensile testing of 3D printed replica and find that experimental observations corroborate with theoretical study.

  20. Wave-particle dualism of spiral waves dynamics.

    Science.gov (United States)

    Biktasheva, I V; Biktashev, V N

    2003-02-01

    We demonstrate and explain a wave-particle dualism of such classical macroscopic phenomena as spiral waves in active media. That means although spiral waves appear as nonlocal processes involving the whole medium, they respond to small perturbations as effectively localized entities. The dualism appears as an emergent property of a nonlinear field and is mathematically expressed in terms of the spiral waves response functions, which are essentially nonzero only in the vicinity of the spiral wave core. Knowledge of the response functions allows quantitatively accurate prediction of the spiral wave drift due to small perturbations of any nature, which makes them as fundamental characteristics for spiral waves as mass is for the condensed matter.

  1. Nonlinear dynamics of breathers in the spiral structures of magnets

    Energy Technology Data Exchange (ETDEWEB)

    Kiselev, V. V., E-mail: kiselev@imp.uran.ru; Raskovalov, A. A. [Russian Academy of Sciences, Mikheev Institute of Metal Physics, Ural Branch (Russian Federation)

    2016-06-15

    The structure and properties of pulsating solitons (breathers) in the spiral structures of magnets are analyzed within the sine-Gordon model. The breather core pulsations are shown to be accompanied by local shifts and oscillations of the spiral structure with the formation of “precursors” and “tails” in the moving soliton. The possibilities for the observation and excitation of breathers in the spiral structures of magnets and multiferroics are discussed.

  2. Cochlea and other spiral forms in nature and art.

    Science.gov (United States)

    Marinković, Slobodan; Stanković, Predrag; Štrbac, Mile; Tomić, Irina; Ćetković, Mila

    2012-01-01

    The original appearance of the cochlea and the specific shape of a spiral are interesting for both the scientists and artists. Yet, a correlation between the cochlea and the spiral forms in nature and art has been very rarely mentioned. The aim of this study was to investigate the possible correlation between the cochlea and the other spiral objects in nature, as well as the artistic presentation of the spiral forms. We explored data related to many natural objects and examined 13,625 artworks created by 2049 artists. We also dissected 2 human cochleas and prepared histologic slices of a rat cochlea. The cochlea is a spiral, cone-shaped osseous structure that resembles certain other spiral forms in nature. It was noticed that parts of some plants are arranged in a spiral manner, often according to Fibonacci numbers. Certain animals, their parts, or their products also represent various types of spirals. Many of them, including the cochlea, belong to the logarithmic type. Nature created spiral forms in the living world to pack a larger number of structures in a limited space and also to improve their function. Because the cochlea and other spiral forms have a certain aesthetic value, many artists presented them in their works of art. There is a mathematical and geometric correlation between the cochlea and natural spiral objects, and the same functional reason for their formation. The artists' imagery added a new aspect to those domains. Obviously, the creativity of nature and Homo sapiens has no limits--like the infinite distal part of the spiral. Copyright © 2012 Elsevier Inc. All rights reserved.

  3. The effect of expert performance microtiming on listeners’ experience of groove in swing or funk music

    Directory of Open Access Journals (Sweden)

    Olivier Senn

    2016-10-01

    Full Text Available This study tested the influence of expert performance microtiming on listeners' groove experience. Two professional rhythm section (bass/drums performances in swing and funk style were recorded, and the performances' original microtemporal deviations from a regular metronomic grid were scaled to several magnitude levels. Music expert (n=79 and non-expert (n=81 listeners rated the groove qualities of stimuli using a newly developed questionnaire that measures three dimensions of the groove experience (Entrainment, Enjoyment, and the absence of Irritation. Findings show that music expert listeners were more sensitive to microtiming manipulations than non-experts. Across both expertise groups and for both styles, groove ratings were high for microtiming magnitudes equal or smaller than those originally performed and decreased for exaggerated microtiming magnitudes. In particular, both the fully quantized music and the music with the originally performed microtiming pattern were rated equally high on groove. This means that neither the claims of PD theory (that microtiming deviations are necessary for groove nor the opposing exactitude hypothesis (that microtiming deviations are detrimental to groove were supported by the data.

  4. Microcirculation within Grooved Substrates regulates Cell Positioning and Cell Docking inside Microfluidic Channels

    Science.gov (United States)

    Manbachi, Amir; Shrivastava, Shamit; Cioffi, Margherita; Chung, Bong Geun; Moretti, Matteo; Demirci, Utkan; Yliperttula, Marjo; Khademhosseini, Ali

    2009-01-01

    Immobilization of cells inside microfluidic devices is a promising approach for enabling studies related to drug screening and cell biology. Despite extensive studies in using grooved substrates for immobilizing cells inside channels, a systematic study of the effects of various parameters that influence cell docking and retention within grooved substrates has not been performed. We demonstrate using computational simulations that the fluid dynamic environment within microgrooves significantly varies with groove width, generating micro-circulation areas in smaller microgrooves. Wall shear stress simulation predicted that shear stresses were in opposite direction in smaller grooves (25 and 50 μm wide) in comparison to those in wider grooves (75 and 100 μm wide). To validate the simulations, cells were seeded within microfluidic devices, where microgrooves of different widths were aligned perpendicularly to the direction of the flow. Experimental results showed that, as predicted, the inversion of the local direction of shear stress within the smaller grooves resulted in alignment of cells on two opposite sides of the grooves under the same flow conditions. Also, the amplitude of shear stress within microgrooved channels significantly influenced cell retainment in the channels. Therefore, our studies suggest that microscale shear stresses greatly influence cellular docking, immobilization, and retention in fluidic systems and should be considered for the design of cell-based microdevices. PMID:18432345

  5. Laser melting of groove defect repair on high thermal conductivity steel (HTCS-150)

    Science.gov (United States)

    Norhafzan, B.; Aqida, S. N.; Fazliana, F.; Reza, M. S.; Ismail, I.; Khairil, C. M.

    2018-02-01

    This paper presents laser melting repair of groove defect on HTCS-150 surface using Nd:YAG laser system. Laser melting process was conducted using JK300HPS Nd:YAG twin lamp laser source with 1064 nm wavelength and pulsed mode. The parameters are pulse repetition frequency (PRF) that is set from 70 to 100 Hz, average power ( P A) of 50-70 W, and laser spot size of 0.7 mm. HTCS-150 samples were prepared with groove dimension of 0.3 mm width and depths of 0.5 mm using EDM wire cut. Groove defect repaired using laser melting process on groove surface area with various parameters' process. The melted surface within the groove was characterized for subsurface hardness profile, roughness, phase identification, chemical composition, and metallographic study. The roughness analysis indicates high PRF at large spot size caused high surface roughness and low surface hardness. Grain refinement of repaired layer was analyzed within the groove as a result of rapid heating and cooling. The hardness properties of modified HTCS inside the groove and the bulk surface increased two times from as received HTCS due to grain refinement which is in agreement with Hall-Petch equation. These findings are significant to parameter design of die repair for optimum surface integrity and potential for repairing crack depth and width of less than 0.5 and 0.3 mm, respectively.

  6. Formation and evolution of Weiyuan-Anyue extension-erosion groove in Sinian system, Sichuan Basin

    Science.gov (United States)

    Li, Zhongquan

    2017-04-01

    Based on comprehensive analysis of deposition and structure, the horizontal and vertical characteristics of the Weiyuan-Anyue erosion-extension groove have been studied using outcrop, drilling, well logging and seismic data. According to the strata, lithology, structure and regional evolution, the Sinian system denuded thickness has been restored to show the development and evolution as well as transformation of the erosion-extension groove in the Tongwan orogeny. The Weiyuan-Anyue extension-erosion groove is distributed along the Penglai-Anyue-Rongchang in NW direction, with the west area steeper than the east in groove. According to the study of the Weiyuan-Longnüsi seismic profile across the middle area of erosion-extension groove, the formation of the Weiyuan-Anyue extension-erosion groove is the synthetic result of different geological processes from differential uplift, the denudation, erosion and dissolution in the Dengying Formation caused by multiple-phase episode grabon or horst movement of the Sinian basement fault. The formation of the Weiyuan-Anyue erosion-extension groove can be divided into three stages, and the erosion and dissolution can be calculated quantitatively by denudation recovery profile, its maximum can reach 600 m.

  7. A stereological approach for measuring the groove angles of intergranular corrosion

    International Nuclear Information System (INIS)

    Gwinner, B.; Borgard, J.-M.; Dumonteil, E.; Zoia, A.

    2017-01-01

    Highlights: • The ICG morphology has been characterized in 3D by X-ray μ-tomography. • The measurement of the angles of the IGC groove on 2D cross sections induces a bias. • A methodology is proposed to estimate the true value of the IGC groove angles in 3D. - Abstract: Non-sensitized austenitic stainless steels can be prone to intergranular corrosion when they are in contact with an oxidizing medium like nitric acid. Intergranular corrosion is characterized by the formation of grooves along the grain boundaries. The angle of these grooves is a key parameter, which directly informs of the intergranular corrosion kinetics. Most of the time, the angles of the grooves are experimentally measured on 2-dimensional cross sections of the corroded samples. This study discusses the relationship between the groove angle measured on 2-dimensional sections and the true groove angle in 3-dimensional space. This approach could also be easily extended to the study of crack angle in the domains of corrosion-fatigue, stress corrosion cracking or mechanical fracture.

  8. SPIRAL2 Week 2012 - Slides of the presentations

    International Nuclear Information System (INIS)

    Staley, F.; Jacquemet, M.; Lewitowicz, M.; Bertrand, P.; Tuske, O.; Caruso, A.; Leyge, J.F.; Perrot, L.; Di Giacomo, M.; Ausset, P.; Moscatello, M.H.; Savalle, A.; Rannou, B.; Lambert, M.; Petit, E.; Hulin, X.; Barre-Boscher, N.; Tusseau-Nenez, S.; Tecchio, L.B.

    2013-01-01

    The main goal of the 5. edition of the SPIRAL2 Week is to present and discuss the current status of the SPIRAL2 project in front of a large community of scientists and engineers. The program of the meeting will include presentations on scientific and technical developments related to the baseline project, experiments and theory. The main topics to be discussed at the conference are: -) physics and detectors at SPIRAL2, -) driver accelerators, -) production of radioactive ion beams (RIB), -) safety, -) buildings and infrastructure, -) RIB facilities worldwide, and -) SPIRAL2 preparatory phase. This document is made up of the slides of the presentations

  9. Algorithms for computing efficient, electric-propulsion, spiralling trajectories

    Data.gov (United States)

    National Aeronautics and Space Administration — Develop techniques for rapidly designing many-revolution, electric-propulsion, spiralling trajectories, including the effects of shadowing, gravity harmonics, and...

  10. Self-regulated model of galactic spiral structure formation.

    Science.gov (United States)

    Cartin, Daniel; Khanna, Gaurav

    2002-01-01

    The presence of spiral structure in isolated galaxies is a problem that has only been partially explained by theoretical models. Because the rate and pattern of star formation in the disk must depend only on mechanisms internal to the disk, we may think of the spiral galaxy as a self-regulated system far from equilibrium. This paper uses this idea to look at a reaction-diffusion model for the formation of spiral structures in certain types of galaxies. In numerical runs of the model, spiral structure forms and persists over several revolutions of the disk, but eventually dies out.

  11. Spread of the spiraling white fly Aleurodicus dispersus (Homoptera ...

    African Journals Online (AJOL)

    Spread of the spiraling white fly Aleurodicus dispersus (Homoptera: Aleyrodidae) and its parasitoids Encarcia species (Hymenoptera: Aphelinidae) on horticultural plants in Northwest and Central Nigeria.

  12. Topological Signatures in the Electronic Structure of Graphene Spirals

    DEFF Research Database (Denmark)

    Avdoshenko, Stas.M.; Koskinen, Pekka; Sevincli, Haldun

    2013-01-01

    and graphene systems. Here, we introduce topologically distinct graphene forms - graphene spirals - and employ density-functional theory to investigate their geometric and electronic properties. We found that the spiral topology gives rise to an intrinsic Rashba spin-orbit splitting. Through a Hamiltonian...... constrained by space curvature, graphene spirals have topologically protected states due to time-reversal symmetry. In addition, we argue that the synthesis of such graphene spirals is feasible and can be achieved through advanced bottom-up experimental routes that we indicate in this work....

  13. Virtual bronchoscopy based on spiral CT images

    Science.gov (United States)

    Englmeier, Karl-Hans; Haubner, Michael; Krapichler, Christian; Schuhmann, Dietrich; Seemann, Mark; Fuerst, H.; Reiser, Maximilian

    1998-06-01

    Purpose: To improve the diagnosis of pathologic modified airways, a visualization system has been developed and tested based on the techniques of digital image analysis, synthesis of spiral CT and the visualization by methods of virtual reality. Materials and Methods: 20 patients with pathologic modifications of the airways (tumors, obstructions) were examined with Spiral-CT. The three-dimensional shape of the airways and the lung tissue is defined by a semiautomatic volume growing method and a following geometric surface reconstruction. This is the basis of a multidimensional display system which visualizes volumes, surfaces and computation results simultaneously. To enable the intuitive and immersive inspection of the airways a virtual reality system, consisting of two graphic engines, a head mounted display system, data gloves and specialized software was integrated. Results: In 20 cases the extension of the pathologic modification of the airways could be visualized with the virtual bronchoscopy. The user interacts with and manipulates the 3D model of the airways in an intuitive and immersive way. In contrast to previously proposed virtual bronchoscopy systems the described method permits truly interactive navigation and detailed exploration of anatomic structures. The system enables a user oriented and fast inspection of the volumetric image data. Conclusion: To support radiological diagnosis with additional information in an easy to use and fast way a virtual bronchoscopy system was developed. It enables the immersive and intuitive interaction with 3D Spiral CTs by truly 3D navigation within the airway system. The complex anatomy of the central tracheobronchial system could be clearly visualized. Peripheral bronchi are displayed up to 5th degree.

  14. Unusual stress fracture in an adolescent baseball pitcher affecting the trochlear groove of the olecranon

    International Nuclear Information System (INIS)

    Blake, Joseph J.; Block, John J.; Kan, J.H.; Hannah, Gene A.

    2008-01-01

    Stress fractures of the proximal ulna are known to occur in throwing athletes. Most cases extend to involve the olecranon, and cases limited to the trochlear groove are rare. In this report we present a 17-year-old elite baseball pitcher with a stress fracture of the trochlear groove of the proximal ulna. Diagnosis was made by demonstration of characteristic signal changes on MRI of the elbow. The fracture occurred at the cortical notch, also known as the pseudodefect of the trochlear groove. This case suggests that the cortical notch serves as an area of weakness predisposing pitchers to development of a stress fracture. (orig.)

  15. Mechanism Analysis of One-Dimensional Quasiperiodic Groove Drag-Reduction

    Science.gov (United States)

    Xue, Wen-Hui; Geng, Xing-Guo; Li, Jie; Li, Feng; Wu, Jun

    2010-10-01

    Grooves arranged in one-dimensional quasiperiodic patterns are prepared by mechanical method. Drag reduction experiments are performed by R/S plus rheometer and the results show that there is a novel drag reduction effect compared with periodic grooves. An equivalent grating model is proposed to investigate the mechanism. It is found that, in comparison with periodic grating, the intensity distributes more uniform in a limited area when the coherent wave gets through quasiperiodic grating. Corresponding to the quasiperiodic grooves, the energy transfers more uniform, which could inhibit the generation of large vortices.

  16. 3-D design method for welding groove and seal weld of reactor CRDM adapter

    International Nuclear Information System (INIS)

    Ma Baiyong; Wang Xiaobin; Zhu Xiaoyong

    2008-01-01

    Based on the analysis of 2 D and 3 D shapes of welding groove and seal weld of reactor CRDM adapter, four intersecting curves are defined, and a method and gist to 3 D design of adapter welding groove and seal weld is proposed. Parameterized design of adapter welding groove and seal weld has been realized using UG software, and the main factors which affect the welding section areas have been analyzed. Compared with the measurement, the error of weld section area of each adapter created by spline fitting method is less than 0.8%. (authors)

  17. Mathematical modeling of photovoltaic thermal PV/T system with v-groove collector

    Science.gov (United States)

    Zohri, M.; Fudholi, A.; Ruslan, M. H.; Sopian, K.

    2017-07-01

    The use of v-groove in solar collector has a higher thermal efficiency in references. Dropping the working heat of photovoltaic panel was able to raise the electrical efficiency performance. Electrical and thermal efficiency were produced by photovoltaic thermal (PV/T) system concurrently. Mathematical modeling based on steady-state thermal analysis of PV/T system with v-groove was conducted. With matrix inversion method, the energy balance equations are explained by means of the investigative method. The comparison results show that in the PV/T system with the V-groove collector is higher temperature, thermal and electrical efficiency than other collectors.

  18. Production and post acceleration scheme for spiral

    International Nuclear Information System (INIS)

    Bibet, D.

    2001-01-01

    SPIRAL, the R.I.B. facility of GANIL uses heavy ion beams to produce radioactive atoms inside a thick target. Atoms are ionised in a compact permanent magnet ECR ion source. The compact cyclotron CIME accelerates the radioactive ions in an energy range from 1.7 to 25 MeV/u. The cyclotron acts as a mass separator with resolving power of 2500. Plastic scintillator and silicon detectors are used to tune the machine at a very low intensity. An overview of the facility, stable beam tests results and the R and D program will be presented. (authors)

  19. Controls and automation in the SPIRAL project

    International Nuclear Information System (INIS)

    Bothner, U.; Boulot, A.; Maherault, J.; Martial, L.

    1999-01-01

    The control and automation team of the R and D of Accelerator-Exotic Beam Department has had in the framework of SPIRAL collaboration the following tasks: 1. automation of the resonator high frequency equipment of the CIME cyclotron; 2. automation of the vacuum equipment, i.e. the low energy line (TBE), the CIME cyclotron, the low energy line (BE); 3. automation of load safety for power supply; 4. for each of these tasks a circuitry file based on the SCHEMA software has been worked out. The programs required in the automation of load safety for power supply (STEP5, PROTOOL, DESIGNER 4.1) were developed and implemented for PC

  20. Galaxy Zoo: dust in spiral galaxies star

    OpenAIRE

    Masters, Karen L.; Nichol, Robert; Bamford, Steven; Mosleh, Moein; Lintott, Chris J.; Andreescu, Dan; Edmondson, Edward M.; Keel, William C.; Murray, Phil; Raddick, M. Jordan; Schawinski, Kevin; Slosar, Anze; Szalay, Alexander S.; Thomas, Daniel; Vandenberg, Jan

    2010-01-01

    We investigate the effect of dust on spiral galaxies by measuring the inclination dependence of optical colours for 24 276 well-resolved Sloan Digital Sky Survey (SDSS) galaxies visually classified via the Galaxy Zoo project. We find clear trends of reddening with inclination which imply a total extinction from face-on to edge-on of 0.7, 0.6, 0.5 and 0.4 mag for the ugri passbands (estimating 0.3 mag of extinction in z band). We split the sample into ‘bulgy’ (early-type) and ‘discy’ (late-typ...

  1. Small centrifugal pumps for low thrust rockets

    Science.gov (United States)

    Gulbrandsen, N. C.; Furst, R. B.; Burgess, R. M.; Scheer, D. D.

    1985-01-01

    This paper presents the results of a combined analytical and experimental investigation of low specific speed pumps for potential use as components of propellant feed systems for low thrust rocket engines. Shrouded impellers and open face impellers were tested in volute type and vaned diffuser type pumps. Full- and partial-emission diffusers and full- and partial-admission impellers were tested. Axial and radial loads, head and efficiency versus flow, and cavitation tests were conducted. Predicted performance of two pumps are compared when pumping water and liquid hydrogen. Detailed pressure loss and parasitic power values are presented for two pump configurations. Partial-emission diffusers were found to permit use of larger impeller and diffuser passages with a minimal performance penalty. Normal manufacturing tolerances were found to result in substantial power requirement variation with only a small pressure rise change. Impeller wear ring leakage was found to reduce pump pressure rise to an increasing degree as the pump flowrate was decreased.

  2. Syncopation affects free body-movement in musical groove.

    Science.gov (United States)

    Witek, Maria A G; Popescu, Tudor; Clarke, Eric F; Hansen, Mads; Konvalinka, Ivana; Kringelbach, Morten L; Vuust, Peter

    2017-04-01

    One of the most immediate and overt ways in which people respond to music is by moving their bodies to the beat. However, the extent to which the rhythmic complexity of groove-specifically its syncopation-contributes to how people spontaneously move to music is largely unexplored. Here, we measured free movements in hand and torso while participants listened to drum-breaks with various degrees of syncopation. We found that drum-breaks with medium degrees of syncopation were associated with the same amount of acceleration and synchronisation as low degrees of syncopation. Participants who enjoyed dancing made more complex movements than those who did not enjoy dancing. While for all participants hand movements accelerated more and were more complex, torso movements were more synchronised to the beat. Overall, movements were mostly synchronised to the main beat and half-beat level, depending on the body-part. We demonstrate that while people do not move or synchronise much to rhythms with high syncopation when dancing spontaneously to music, the relationship between rhythmic complexity and synchronisation is less linear than in simple finger-tapping studies.

  3. Following the canyon to reach and remove olfactory groove meningiomas.

    Science.gov (United States)

    Stefini, Roberto; Zenga, Francesco; Giacomo, Esposito; Bolzoni, Andrea; Tartara, Fulvio; Spena, Giannantonio; Ambrosi, Claudia; Fontanella, Marco M

    2017-04-01

    Olfactory groove meningiomas (OGMs) represent approximately 10% of all intracranial meningiomas. They arise in the olfactory fossa, a variable depression delimited by the lateral lamella and perpendicular plate. The cribriform plate with the lateral lamella and ethmoidal and orbital roof could be viewed as a 'canyon' with the frontal sinus as the main entrance. Between January 2000 and December 2013, 32 consecutive patients underwent removal of OGMs through this 'canyon' at the Department of Neurosurgery of Brescia and Turin. Complete removal was achieved in all patients with this trans-frontal sinus subcranial approach (Simpson grade I; mean lesion volume, 46.6 cm3). Five patients (15.6%) experienced nasal CSF leakage, treated with external lumbar drain positioning for 4 days and resolved in all cases but one, which was re-operated. Two patients (6.2%) during the CSF leakage experienced meningitis at day 7 after surgery, both successfully treated by intravenous antibiotic therapy. After one month, one patient developed hydrocephalus, treated with a ventricular peritoneal shunt. In one patient, traction on the OGM caused bleeding of the callosomarginal artery, which was coagulated with superior frontal gyrus ischemia without neurological consequences. Glasgow Outcome Scale Score at 6 months was V in 29 patients, IV in one patient, and I in two patients. Advantages with this approach may include easy and early control of blood supply from its insertion in the skull base, minimal frontal lobe retraction, preservation of the frontal veins draining to the sagittal sinus, and a satisfactory aesthetic outcome.

  4. Condensation and evaporation transitions in deep capillary grooves.

    Science.gov (United States)

    Malijevský, Alexandr; Parry, Andrew O

    2014-09-03

    We study the order of capillary condensation and evaporation transitions of a simple fluid adsorbed in a deep capillary groove using a fundamental measure density functional theory (DFT). The walls of the capillary interact with the fluid particles via long-ranged, dispersion, forces while the fluid-fluid interaction is modelled as a truncated Lennard-Jones-like potential. We find that below the wetting temperature Tw condensation is first-order and evaporation is continuous with the metastability of the condensation being well described by the complementary Kelvin equation. In contrast above Tw both phase transitions are continuous and their critical singularities are determined. In addition we show that for the evaporation transition above Tw there is an elegant mapping, or covariance, with the complete wetting transition occurring at a planar wall. Our numerical DFT studies are complemented by analytical slab model calculations which explain how the asymmetry between condensation and evaporation arises out of the combination of long-ranged forces and substrate geometry.

  5. Observations on the effects of grooved surfaces on the interfacial torque in highly loaded rolling and sliding tests

    DEFF Research Database (Denmark)

    Janakiraman, Shravan; Klit, Peder; Jensen, Niels Steenfeldt

    2014-01-01

    Some efforts have been undertaken to study the effects of grooved surfaces on the interfacial film thickness and torque between two contacting non-conformal surfaces under heavy loads. Transverse grooves of micrometer scale depth were engraved on polished, flat ring surfaces using established...... industrial methods like laser engraving and wire cutting. The grooved surfaces were then run against a polished flat surface at loads corresponding to high normal Hertzian pressures. Experiments were conducted to study the effects of the following parameters on the interfacial torque-groove depth, groove...

  6. An improved design of spiral tube assembly for separation of proteins by high-speed counter-current chromatography.

    Science.gov (United States)

    Dasarathy, Dhweeja; Ito, Yoichiro

    2015-10-30

    A new spiral tube assembly was designed to improve the column capacity and partition efficiency for protein separation. This spiral tube assembly has greater column capacity than the original tubing because of an increase in radial grooves from 4 to 12 to accommodate more spiral layers and 12 narrow spots instead of 4 in each circular loop to interrupt the laminar flow that causes sample band broadening. Standard PTFE tubing (1.6mm ID) and the modified flat-twisted tubing were used as the separation column. The performances of both assemblies were compared for separating three stable test proteins including cytochrome c, myoglobin, and lysozyme using a two phase aqueous-aqueous solvent system composed of polyethylene glycol 1000 (12.5% w/w) and dibasic potassium phosphate (12.5% w/w). All samples were run at 1, 2, 3, and 5mL/min at both 800rpm and 1000rpm. The separation of these three protein samples produced high stationary phase retentions at 1, 2, and 3mL/min, yet separated efficiently at 5mL/min in 40min. After comparing the separation efficiency in terms of the peak resolutions, theoretical plate numbers, and separation times, it was determined that the flat-twisted tubing was more effective in separating these protein samples. In order to validate the efficacy of this novel assembly, a mixture of five protein samples (cytochrome c, myoglobin, ovalbumin, lysozyme, and hemoglobin) were separated, under the optimal conditions established with these three protein samples, at 1mL/min with a revolution speed of 1000rpm. There were high stationary phase retentions of around 60%, with effective separations, demonstrating the efficiency of the flat-twisted spiral tube assembly. The separation time of 6h was a limitation but can potentially be shortened by improving the strength of the column that will permit an increase in revolution speed and flow rate. This novel spiral separation column will allow rapid and efficient separation of mixtures with high yield of the

  7. Electronics Engineering Department Thrust Area report FY'84

    International Nuclear Information System (INIS)

    Minichino, C.; Phelps, P.L.

    1984-01-01

    This report describes the work of the Electronics Engineering Department Thrust Areas for FY'84: diagnostics and microelectronic engineering; signal and control engineering; microwave and pulsed power engineering; computer-aided engineering; engineering modeling and simulation; and systems engineering. For each Thrust Area, an overview and a description of the goals and achievements of each project is provided

  8. Transient analysis of blowdown thrust force under PWR LOCA

    International Nuclear Information System (INIS)

    Yano, Toshikazu; Miyazaki, Noriyuki; Isozaki, Toshikuni

    1982-10-01

    The analytical results of blowdown characteristics and thrust forces were compared with the experiments, which were performed as pipe whip and jet discharge tests under the PWR LOCA conditions. The blowdown thrust forces obtained by Navier-Stokes momentum equation about a single-phase, homogeneous and separated two-phase flow, assuming critical pressure at the exit if a critical flow condition was satisfied. The following results are obtained. (1) The node-junction method is useful for both the analyses of the blowdown thrust force and of the water hammer phenomena. (2) The Henry-Fauske model for subcooled critical flow is effective for the analysis of the maximum thrust force under the PWR LOCA conditions. The jet thrust parameter of the analysis and experiment is equal to 1.08. (3) The thrust parameter of saturated blowdown has the same one with the value under pressurized condition when the stagnant pressure is chosen as the saturated one. (4) The dominant terms of the blowdown thrust force in the momentum equation are the pressure and momentum terms except that the acceleration term has large contribution only just after the break. (5) The blowdown thrust force in the analysis greatly depends on the selection of the exit pressure. (author)

  9. Back-thrusting in Lesser Himalaya: Evidences from magnetic fabric ...

    Indian Academy of Sciences (India)

    The present study aims to understand evolution of the Lesser Himalaya, which consists of (meta) sedimentaryand crystalline rocks. Field studies, microscopic and rock magnetic investigations have beencarried out on the rocks near the South Almora Thrust (SAT) and the North Almora Thrust (NAT),which separates the ...

  10. Dynamic Model for Thrust Generation of Marine Propellers

    DEFF Research Database (Denmark)

    Blanke, Mogens; Lindegaard, Karl-Petter; Fossen, Thor I.

    2000-01-01

    Mathematical models of propeller thrust and torque are traditionally based on steady state thrust and torque characteristics obtained in model basin or cavitation tunnel tests. Experimental results showed that these quasi steady state models do not accurately describe the transient phenomena in a...

  11. Back-thrusting in Lesser Himalaya: Evidences from magnetic fabric ...

    Indian Academy of Sciences (India)

    Back-thrusts originated below the Lesser Himalayan rocks, probably from the Main Boundary Thrust, and propagated across the sedimentary ... and Asian plates, ∼55 Ma ago, motored the evolution of the ∼2400 km long belt of the ...... earthquakes along the Himalayan Arc and long term forecasting; Earthq. Predict., pp.

  12. 2D array based on fermat spiral

    Science.gov (United States)

    Martínez, O.; Martín, C. J.; Godoy, G.; Ullate, L. G.

    2010-01-01

    The main challenge faced by 3D ultrasonic imaging with 2D array transducer is the large number of elements required to achieve an acceptable level of quality in the images. Therefore, the optimization of the array layout to reduce the number of active elements in the aperture has been a research topic in the last years. Nowadays, CMUT array technology has made viable the production of 2D arrays with larger flexibility on elements size, shape and position. This is opening new options in 2D array design, allowing to revise as viable alternatives others layouts that had been studied in the past, like circular and Archimedes spiral layout. In this work the problem of designing an imaging system array with a diameter of 60 λ and a limited number of elements using the Fermat spiral layout has been studied. This study has been done for two different numbers of electronic channels (N = 128 and N = 256). As summary, a general discussion of the results and the most interesting cases are presented.

  13. Spiral-shaped reactor for water disinfection

    KAUST Repository

    Soukane, Sofiane

    2016-04-20

    Chlorine-based processes are still widely used for water disinfection. The disinfection process for municipal water consumption is usually carried out in large tanks, specifically designed to verify several hydraulic and disinfection criteria. The hydrodynamic behavior of contact tanks of different shapes, each with an approximate total volume of 50,000 m3, was analyzed by solving turbulent momentum transport equations with a computational fluid dynamics code, namely ANSYS fluent. Numerical experiments of a tracer pulse were performed for each design to generate flow through curves and investigate species residence time distribution for different inlet flow rates, ranging from 3 to 12 m3 s−1. A new nature-inspired Conch tank design whose shape follows an Archimedean spiral was then developed. The spiral design is shown to strongly outperform the other tanks’ designs for all the selected plug flow criteria with an enhancement in efficiency, less short circuiting, and an order of magnitude improvement in mixing and dispersion. Moreover, following the intensification philosophy, after 50% reduction in its size, the new design retains its properties and still gives far better results than the classical shapes.

  14. Fold and thrust systems in Mass Transport Deposits

    Science.gov (United States)

    Alsop, G. I.; Marco, S.; Levi, T.; Weinberger, R.

    2017-01-01

    Improvements in seismic reflection data from gravity-driven fold and thrust systems developed in offshore Mass Transport Deposits (MTDs) reveal a number of significant features relating to displacement along thrusts. However, the data are still limited by the resolution of the seismic method, and are unable to provide detail of local fold and thrust processes. Investigation of exceptional gravity-driven contractional structures forming part of MTDs in lacustrine deposits of the Dead Sea Basin, enables us to present the first detailed outcrop analysis of fold and thrust systems cutting unlithified 'soft' sediments. We employ a range of established geometric techniques to our case study, including dip isogons, fault-propagation fold charts and displacement-distance diagrams previously developed for investigation of thrusts and folds in lithified rocks. Fault-propagation folds in unlithified sediments display tighter interlimb angles compared to models developed for lithified sequences. Values of stretch, which compares the relative thickness of equivalent hangingwall and footwall sequences measured along the fault plane, may be as low as only 0.3, which is significantly less than the minimum 0.5 values reported from thrusts cutting lithified rocks, and reflects the extreme variation in stratigraphic thickness around thrust-related folds. We suggest that the simple shear component of deformation in unlithified sediments may modify the forelimb thickness and interlimb angles to a greater extent than in lithified rocks. The average spacing of thrust ramps and the thickness of the thrust sequence display an approximate 5:1 ratio across a range of scales in MTDs. In general, thicker hangingwall and footwall sequences occur with larger thrust displacements, although displacement patterns on thrusts cutting unlithified (yet cohesive) sediments are more variable than those in lithified rocks. Line-length restoration of thrust systems in MTDs reveals 42% shortening, which

  15. Palatal radicular groove: Clinical implications of early diagnosis and surgical sealing

    Directory of Open Access Journals (Sweden)

    P Corrêa-Faria

    2011-01-01

    Full Text Available Palatal radicular groove is a discreet alteration in tooth morphology, characterized by an invagination that begins near the cingulum of the tooth and moves in an apical direction. Clinically, palatal radicular groove may be associated with periodontal and/or endodontic problems. This paper describes a clinical case of a young patient with palatal radicular groove with no signs of periodontal disease or endodontic impairment. An early diagnosis was made and treatment consisted of surgical sealing of the defect. After a 2-year period, reexaminations demonstrated adequate hygiene, maintenance of tooth vitality and periodontal health. The early diagnosis and sealing of the groove observed surgically made the root surface smooth, avoiding subgingival bacterial plaque buildup, and preventing possible periodontal and/or pulp impairment stemming from the defect.

  16. Effectiveness of noise barriers installed adjacent to transverse grooved concrete pavement.

    Science.gov (United States)

    2009-10-16

    In recent years the Ohio Department of Transportation (ODOT) has reconstructed a number of roadways where asphalt pavements were replaced with random transverse grooved concrete pavements. Upon completion, residents living adjacent to the reconstruct...

  17. 'Tongue-and-groove' effect in intensity modulated radiotherapy with static multileaf collimator fields

    International Nuclear Information System (INIS)

    Que, W; Kung, J; Dai, J

    2004-01-01

    The 'tongue-and-groove problem' in step-and-shoot delivery of intensity modulated radiotherapy is investigated. A 'tongue-and-groove' index (TGI) is introduced to quantify the 'tongue-and-groove' effect in step-and-shoot delivery. Four different types of leaf sequencing methods are compared. The sliding window method and the reducing level method use the same number of field segments to deliver the same intensity map, but the TGI is much less for the reducing level method. The leaf synchronization method of Van Santvoort and Heijmen fails in step-and-shoot delivery, but a new method inspired by the method of Van Santvoort and Heijmen is shown to eliminate 'tongue-and-groove' underdosage completely

  18. Design curves for optimizing stability of herringbone-grooved journal bearings

    Science.gov (United States)

    Fleming, D. P.; Hamrock, B. J.

    1973-01-01

    Curves span wide range of operating conditions, including: lubricant compressibility numbers from 0 to 80, bearing length-to-diameter ratios from 1/4 to 2, and either rotating or stationary grooved members.

  19. Effectiveness of noise barriers installed adjacent to transverse grooved concrete pavement : executive summary report.

    Science.gov (United States)

    2009-10-16

    In recent years the Ohio Department of Transportation (ODOT) has reconstructed a number of roadways where asphalt pavements were replaced with concrete pavements which were finished with a random transverse grooved surface texture (ODOT specification...

  20. Standardized performance tests of collectors of solar thermal energy: Prototype moderately concentrating grooved collectors

    Science.gov (United States)

    1976-01-01

    Prototypes of moderately concentrating grooved collectors were tested with a solar simulator for varying inlet temperature, flux level, and incident angle. Collector performance is correlated in terms of inlet temperature and flux level.

  1. Large eddy simulation of the subcritical flow over a V grooved circular cylinder

    International Nuclear Information System (INIS)

    Alonzo-García, A.; Gutiérrez-Torres, C. del C.; Jiménez-Bernal, J.A.

    2015-01-01

    Highlights: • We compared numerically the turbulent flow over a smooth circular cylinder and a V grooved cylinder in the subcritical regime. • Turbulence intensities in both streamwise and normal direction suffered attenuations. • The swirls structures on grooves peaks seemed to have a cyclic behavior. • The evolution of the flow inside grooves showed that swirls structures located in peaks suffered elongations in the normal direction. • The secondary vortex structures formed in the grooved cylinder near wake were smaller in comparison of the smooth cylinder flow. - Abstract: In this paper, a comparative numerical study of the subcritical flow over a smooth cylinder and a cylinder with V grooves (Re = 140,000) is presented. The implemented technique was the Large Eddy Simulation (LES), which according to Kolmogorov's theory, resolves directly the most energetic largest eddies and models the smallest and considered universal high frequency ones. The Navier-Stokes (N-S) equations were solved using the commercial software ANSYS FLUENT V.12.1, which applied the finite volume method (FVM) to discretize these equations in their unsteady and incompressible forms. The grid densities were 2.6 million cells and 13.5 million cells for the smooth and V grooved cylinder, respectively. Both meshes were composed of structured hexahedral cells and close to the wall of the cylinders, additional refinements were employed in order to obtain y +<5 values. All cases were simulated during at least 15 vortex shedding cycles with the aim of obtaining significant statistical data. Results: showed that for both cases (smooth and V grooved cylinder flow), the numerical code was capable of reproducing the most important physical quantities of the subcritical regime. Velocity distribution and turbulence intensity in the flow direction suffered a slight attenuation along the wake, as a consequence of grooves perturbation, which also caused an increase in the pressure coefficient

  2. Early Cenozoic Multiple Thrust in the Tibetan Plateau

    Directory of Open Access Journals (Sweden)

    Zhenhan Wu

    2013-01-01

    Full Text Available Recently completed regional geological mapping at a scale of 1 : 250,000 or larger across all of the Tibetan Plateau coupled with deep seismic surveys reveals for the first time a comprehensive depiction of the major early Cenozoic thrust systems resulting from the northward subduction of the Indian Continental Plate. These systems define a series of overlapping north-dipping thrust sheets that thickened the Tibetan crust and lead to the rise of the plateau. The few south-dipping thrusts present apparently developed within a sheet when the back moved faster than the toe. Many of the thrusts are shown to extend to the middle-lower crustal depths by seismic data. The regional thrust systems are the Main Central, Renbu-Zedong, Gangdese, Central Gangdese, North Gangdese, Bangoin-Nujiang, Qiangtang, Hohxil, and South Kunlun Thrusts. The minimal southward displacements of the South Kunlun, Hohxil, South Qiangtang, and Central Gangdese Thrusts are estimated to be 30 km, 25 km, 150 km and 50 km, respectively. Deep thrusting began in the Himalaya-Tibetan region soon after India-Eurasia continental collision and led to crustal thickening and subsequent uplift of the Tibetan Plateau during Late Eocene-Early Miocene when the systems were mainly active. The major thrust systems ceased moving in Early Miocene and many were soon covered by lacustrine strata. This activity succeeded in the late Cenozoic to crustal extension and strike-slip movement in the central Tibetan Plateau. The revelation of the full array of the early Cenozoic thrust systems provides a much more complete understanding of the tectonic framework of the Tibetan Plateau.

  3. A phenomenological theory for polarization flop in spiral multiferroic ...

    Indian Academy of Sciences (India)

    driven polarization flop in TbMnO3. The Néel wall-like magnetic structure in spiral multiferroics induces a space-dependent internal magnetic field which exerts a torque on spins to rotate bc-spiral to abspiral. The external magnetic field is argued ...

  4. A phenomenological theory for polarization flop in spiral multiferroic ...

    Indian Academy of Sciences (India)

    a space-dependent internal magnetic field which exerts a torque on spins to rotate bc-spiral to ab- spiral. The external ... Fv; 75.85.+t. Electric control of magnetization and magnetic control of polarization have been long ... divergence of magnetization, an internal field is induced which has important physical. Figure 1. ab ...

  5. On galaxy spiral arms' nature as revealed by rotation frequencies

    NARCIS (Netherlands)

    Roca-Fabrega, Santi; Valenzuela, Octavio; Figueras, Francesca; Romero-Gomez, Merce; Velazquez, Hector; Antoja Castelltort, Teresa; Pichardo, Barbara

    2013-01-01

    High-resolution N-body simulations using different codes and initial condition techniques reveal two different behaviours for the rotation frequency of transient spiral arms like structures. Whereas unbarred discs present spiral arms nearly corotating with disc particles, strong barred models

  6. Star formation and the surface brightness of spiral galaxies

    International Nuclear Information System (INIS)

    Phillipps, S.; Disney, M.

    1985-01-01

    The (blue) surface brightness of spiral galaxies is significantly correlated with their Hα linewidth. This can be most plausibly interpreted as a correlation of surface brightness with star formation rate. There is also a significant difference in surface brightness between galaxies forming stars in a grand design spiral pattern and those with floc star formation regions. (author)

  7. Up the Down Spiral with English: Guidelines, Project Insight.

    Science.gov (United States)

    Catholic Board of Education, Diocese of Cleveland, OH.

    This curriculum guide presents the philosophy, objectives, and processes which unify a student-centered English program based on Jerome Bruner's concept of the spiral curriculum. To illustrate the spiraling of the learning process (i.e., engagement, perception, interpretation, evaluation, and personal integration), the theme of "hero" is traced…

  8. The cold interstellar medium - An HI view of spiral galaxies

    NARCIS (Netherlands)

    Sancisi, R; Bender, R; Davies, RL

    1996-01-01

    An HI view of spiral galaxies is presented. In the first part the standard picture of isolated, normal spiral galaxies is briefly reviewed. In the second part attention is drawn to all those phenomena, such as tidal interactions, accretion and mergers, that depend on the galaxy environment and seem

  9. Propagation of Channel Plasmons at the Visible Regime in Aluminum V-Groove Waveguides

    DEFF Research Database (Denmark)

    Lotan, Oren; Smith, Cameron; Bar-David, Jonathan

    2016-01-01

    Aluminum plasmonics is emerging as a promising platform in particular for the ultraviolet-blue spectral band. We present the experimental results of propagating channel plasmon-polaritons (CPP) waves in aluminum coated V-shaped waveguides at the short visible wavelength regime. The V-grooves are ......-grooves are fabricated by a process involving UV-photolithography, crystallographic silicon etching, and metal deposition. Polarization measurements of coupling demonstrate a preference to the TM-aligned mode, as predicted in simulations....

  10. Effect of heat treatment on the grooving corrosion resistance of ERW pipes

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jong Kwon; Lee, Jae Young; Lim, Soo Hyun; Park, Ji Hwan; Seo, Bo Min; Kim, Seon Hwa [Soonchunhyang University, Asan (Korea, Republic of)

    2002-06-15

    The v-sharp grooving corrosion of ERW(electrical resistance welding) steel pipes limited their wide application in the industry in spite of their high productivity and efficiency. The grooving corrosion is caused mainly by the different microstructures between the matrix and weld that is formed during the rapid heating and cooling cycle in welding. By this localized corrosion reaction of pipes, it evolves economic problems such as the early damage of industrial facilities and pipe lines of apartment, and water pollution. Even though the diminishing of sulfur content is most effective to decrease the susceptibility of grooving corrosion, it requires costly process. In this study, improvement of grooving corrosion resistance was pursuited by post weld heat treatment in the temperature range between 650 .deg. C and 950 .deg. C. Also, the effect of heat input in the welding was investigated. By employing chromnoamperometry and potentiodynamic experiment, the corrosion rate and grooving corrosion index({alpha}) were obtained. It was found that heat treatment could improve the grooving corrosion resistance. Among them, the heat treated at 900 .deg. C and 950 .deg. C had excellent grooving corrosion resistance. The index of heat treated specimen at 900 .deg. C and 950 .deg. C were 1.0, 1.2, respectively, which are almost immune to the grooving corrosion. Potential difference after the heat treatment, between base and weld metal was decreased considerably. While the as-received one measured 61{approx}71 mV, that of the 900 .deg. C heat treated steel pipe measured only 10mV. The results were explained and discussed

  11. Optimal Tempo for Groove: Its Relation to Directions of Body Movement and Japanese nori

    Directory of Open Access Journals (Sweden)

    Takahide Etani

    2018-04-01

    Full Text Available The tendency for groove-based music to induce body movements has been linked to multiple acoustical factors. However, it is unclear how or whether tempo affects groove, although tempo significantly affects other aspects of music perception. To address this issue, the present study investigated effects of tempo, specific rhythmic organizations of patterns, and syncopation on groove and the induction of the sensation of wanting to move. We focused on the directions of body movement in particular by taking into account nori, which is an indigenous Japanese musical term used not only synonymously with groove, but also as a spatial metaphor indicating vertical or horizontal movement directions. Thus, the present study explored how groove was felt and defined, as well as how musical factors induced the sensation of wanting to move in cross-cultural context. A listening experiment was conducted using drum breaks as stimuli. Stimuli consisted of various rhythm patterns at six tempi from 60 to 200 BPM. The main findings are that: (1 an optimal tempo for groove existed for drum breaks at around 100–120 BPM, (2 an optimal tempo existed for the sensation of wanting to move the body in specific directions (i.e., back-and-forth and side-to-side, (3 groove and nori shared a similar concept of wanting to move but differed on several points (i.e., association with sense of pulse and fast tempo. Overall, the present study suggests that there is an optimal tempo for body movement related to groove. This finding has implications for the use of music or rhythmic stimuli to induce smooth motion in rehabilitation, therapy, or dance.

  12. Plasmonic V-groove waveguides with Bragg grating filters via nanoimprint lithography

    DEFF Research Database (Denmark)

    Smith, Cameron L. C.; Desiatov, Boris; Goykmann, Ilya

    2012-01-01

    We demonstrate spectral filtering with state-of-the-art Bragg gratings in plasmonic V-groove waveguides fabricated by wafer scale processing based on nanoimprint lithography. Transmission spectra of the devices having 16 grating periods exhibit spectral rejection of the channel plasmon polaritons...... with effective refractive index values calculated by finite element simulations in COMSOL. The results represent advancement towards the implementation of plasmonic V-grooves with greater functional complexity and mass-production compatibility....

  13. Schwann cell interactions with polymer films are affected by groove geometry and film hydrophilicity

    International Nuclear Information System (INIS)

    Mobasseri, S A; Downes, S; Terenghi, G

    2014-01-01

    We have developed a biodegradable polymer scaffold made of a polycaprolactone/polylactic acid (PCL/PLA) film. Surface properties such as topography and chemistry have a vital influence on cell–material interactions. Surface modifications of PCL/PLA films were performed using topographical cues and UV–ozone treatment to improve Schwann cell organisation and behaviour. Schwann cell attachment, alignment and proliferation were evaluated on the grooved UV–ozone treated and non-treated films. Solvent casting of the polymer solution on patterned silicon substrates resulted in films with different groove shapes: V (V), sloped (SL) and square (SQ) shapes. Pitted films, with no grooves, were prepared as a negative control. The UV–ozone treatment was performed to increase hydrophilicity. The process specifications for UV–ozone treatment were evaluated and 5 min radiation time and 6 cm distance to the UV source were suggested as the optimal practise. When cultured on grooved films, Schwann cells elongated on the V and SL shape grooves without crossing over, and grew in the direction of the grooves. However, there was less elongation with more crossing over on the SQ shape grooves. The maximum cell length (511 μm) was observed on the treated V-grooved films. The cells cultured on pitted UV–ozone treated surfaces showed random arrangements with no increase in length. We have demonstrated that the synergic effects of physical cues combined with UV–ozone treatment have the potential to enhance Schwann cell morphology and alignment. (paper)

  14. Study on Burr Formation at the Top Edge in Rectangular Groove Cutting

    OpenAIRE

    Wen Jun Deng; Zi Chun Xie; Ping Lin; Tong Kui Xu

    2012-01-01

    Previous research on burr formation in machining operations has usually been limited to the study of the rollover burr in the cutting direction. In this paper, a 3D finite element model to simulate rectangular groove cutting operation has been developed using commercial finite element software, employing experimentally determined mechanical properties at elevated strain rates and temperatures. The plastic deformation behavior and three-dimensional burr formation during rectangular groove cutt...

  15. Preservation of olfaction in surgery of olfactory groove meningiomas.

    Science.gov (United States)

    Jang, Woo-Youl; Jung, Shin; Jung, Tae-Young; Moon, Kyung-Sub; Kim, In-Young

    2013-08-01

    Olfaction is commonly considered as secondary among the sensory functions, perhaps reflecting a lack of interest in sparing olfaction after surgery for the olfactory groove meningiomas (OGM). However, considering the repercussions of olfaction for the quality of life, the assessment of post-operative olfaction should be necessary. We retrospectively reviewed the olfactory outcome in patients with OGM and investigated the factors associated with sparing the post-operative olfaction. Between 1993 and 2012, 40 patients with OGM underwent surgical resection and estimated the olfactory function using the Korean version of "Sniffin'Sticks" test (KVSS). Variable factors, such as tumor size, degree of preoperative edema, tumor consistency, preoperative olfactory function, surgical approaches, patient's age, and gender were analyzed with attention to the post-operative olfactory function. Anatomical and functional preservation of olfactory structures were achieved in 26 patients (65%) and 22 patients (55%), respectively. Among the variable factors, size of tumor was significant related to the preservation of post-operative olfaction. (78.6% in size4 cm, p=0.035). Sparing the olfaction was significantly better in patients without preoperative olfactory dysfunction (84.6%) compared with ones with preoperative olfactory dysfunction (40.7%, p=0.016). The frontolateral approach achieved much more excellent post-operative olfactory function (71.4%) than the bifrontal approach (36.8%, p=0.032). If the tumor was smaller than 4 cm and the patients did not present olfactory dysfunction preoperatively, the possibility of sparing the post-operative olfaction was high. Among the variable surgical approaches, frontolateral route may be preferable sparing the post-operative olfaction. Copyright © 2012 Elsevier B.V. All rights reserved.

  16. Topographic Beta Spiral and Onshore Intrusion of the Kuroshio Current

    Science.gov (United States)

    Yang, De-Zhou; Huang, Rui Xin; Yin, Bao-shu; Feng, Xing-Ru; Chen, Hai-ying; Qi, Ji-Feng; Xu, Ling-jing; Shi, Yun-long; Cui, Xuan; Gao, Guan-Dong; Benthuysen, Jessica A.

    2018-01-01

    The Kuroshio intrusion plays a vitally important role in carrying nutrients to marginal seas. However, the key mechanism leading to the Kuroshio intrusion remains unclear. In this study we postulate a mechanism: when the Kuroshio runs onto steep topography northeast of Taiwan, the strong inertia gives rise to upwelling over topography, leading to a left-hand spiral in the stratified ocean. This is called the topographic beta spiral, which is a major player regulating the Kuroshio intrusion; this spiral can be inferred from hydrographic surveys. In the world oceans, the topographic beta spirals can be induced by upwelling generated by strong currents running onto steep topography. This is a vital mechanism regulating onshore intruding flow and the cross-shelf transport of energy and nutrients from the Kuroshio Current to the East China Sea. This topographic beta spiral reveals a long-term missing link between the oceanic general circulation theory and shelf dynamic theory.

  17. Spatial and mass distributions of molecular clouds and spiral structure

    International Nuclear Information System (INIS)

    Kwan, J.; Valdes, F.; National Optical Astronomy Observatories, Tucson, AZ)

    1987-01-01

    The growth of molecular clouds resulting from cloud-cloud collisions and coalescence in the Galactic ring between 4 and 8 kpc are modeled, taking into account the presence of a spiral potential and the mutual cloud-cloud gravitational attraction. The mean lifetime of molecular clouds is determined to be about 200 million years. The clouds are present in both spiral arm and interarm regions, but a spiral pattern in their spatial distribution is clearly discernible, with the more massive clouds showing a stronger correlation with the spiral arms. As viewed from within the Galactic disk, however, it is very difficult to ascertain that the molecular cloud distribution in longitude-velocity space has a spiral pattern. 19 references

  18. Some statistical properties of spiral galaxies along the Hubble sequence

    Science.gov (United States)

    Ma, Jun; Zhao, Jun-liang; Zhang, Fei-peng; Peng, Qiu-he

    A statistical study has been made for the variations along the Hubble sequence, os such parameters as the degree of tightness of winding of spiral arm λ, the pitch angle μ, the flatness of the disk H/ D25 and the thickness H along the Hubble sequence for 365 spiral galaxies published in A&Ap Supplement Series. The mean values of these quantities for the various Hubble types have been obtained for the first time. The results of the statistics show clearly 1) that the Hubble classification of spiral galaxies is one which has only a qualitative and statistical significance, and 2) that the dispersion relation in the density wave theory is valid for most spiral galaxies, i.e., the arms of most spiral galaxies satisfy the requirements of being tightly wound.

  19. The Effects of Spiral Taping Treatment on Low Back Pain

    Directory of Open Access Journals (Sweden)

    Hwang Jae-Ok

    2006-02-01

    Full Text Available Objective : The purpose of this study is to estimate the effects of spiral taping treatment on low back pain. Methods : 420 low back pain patients were treated with spiral taping or spiral taping plus herbal medicine, and no other treatments such as acupuncture, herbal acupuncture, and chiropractic therapy were added. We evaluated the improvement by physical examination and pain. Results : 364 patients felt no pain or inconvenience of daily life and 43 patients showed improvement of pain or symptom after 1 month of treatment. 13 patients showed same pain with before treatment. Conclusions : These results suggest spiral taping treatments contribute to the improvement of low back pain. Further study is needed for the confirmation of this effect of spiral taping treatments on low back pain.

  20. Cold test of deep groove plarizer for 170 GHz ECCD system

    International Nuclear Information System (INIS)

    Saigusa, M.; Ookouti, K.; Sazawa, S.; Yuasa, S.; Takei, N.; Takahashi, K.; Sakamoto, K.; Imai, T.

    2001-01-01

    The single deep groove mirror was proposed as a new concept polarizer instead of the conventional two mirror polarizers for producing ordinary (or extraordinary) wave with high mode purity at an arbitrary injection angle in electron cyclotron current drive (ECCD) experiments. The estimated mode purity of O and X waves on the plasma surface is expected to be higher than about 93% for reasonable ECCD experimental conditions. The three types of deep groove mirrors, which are the rectangular groove mirror and the non-rectangular one, are manufactured and tested at the frequency range from 140 GHz to 170 GHz and the power level of 30 mW. The groove parameters are the period of 0.9-1 mm, the ridge width of 0.45-0.5 mm, and the groove depth of 1.98 mm, which is deeper than a wavelength at 170 GHz. The measured results of deep groove polarizers agree with the theoretical predictions, qualitatively. Those prove the feasibility of a single mirror polarizer for ECCD system

  1. Grooved surface topography alters matrix-metalloproteinase production by human fibroblasts

    Energy Technology Data Exchange (ETDEWEB)

    Brydone, Alistair S; Dominic Meek, R M [Department of Orthopaedics, Southern General Hospital, 1345 Govan Road, Glasgow G51 4TF (United Kingdom); Dalby, Matthew J; Berry, Catherine C; McNamara, Laura E, E-mail: alibrydone@gmail.com [Centre for Cell Engineering, Joseph Black Building, Institute of Molecular, Cell and Systems Biology, College of Medical, Veterinary and Life Sciences, University of Glasgow, Glasgow G12 8QQ (United Kingdom)

    2011-06-15

    Extracellular matrix (ECM) remodelling is an essential physiological process in which matrix-metalloproteinases (MMPs) have a key role. Manipulating the manner in which cells produce MMPs and ECMs may enable the creation of a desired tissue type, i.e. effect repair, or the prevention of tissue invasion (e.g. metastasis). The aim of this project was to determine if culturing fibroblasts on grooved topography altered collagen deposition or MMP production. Human fibroblasts were seeded on planar or grooved polycaprolactone substrates (grooves were 12.5 {mu}m wide with varying depths of 240 nm, 540 nm or 2300 nm). Cell behaviour and collagen production were studied using fluorescence microscopy and the spent culture medium was assessed using gel zymography to detect MMPs. Total collagen deposition was high on the 240 nm deep grooves, but decreased as the groove depth increased, i.e. as cell contact guidance decreased. There was an increase in gelatinase on the 2300 nm deep grooved topography and there was a difference in the temporal expression of MMP-3 observed on the planar surface compared to the 540 nm and 2300 nm topographies. These results show that topography can alter collagen and MMP production. A fuller understanding of these processes may permit the design of surfaces tailored to tissue regeneration e.g. tendon repair.

  2. Grooved surface topography alters matrix-metalloproteinase production by human fibroblasts

    International Nuclear Information System (INIS)

    Brydone, Alistair S; Dominic Meek, R M; Dalby, Matthew J; Berry, Catherine C; McNamara, Laura E

    2011-01-01

    Extracellular matrix (ECM) remodelling is an essential physiological process in which matrix-metalloproteinases (MMPs) have a key role. Manipulating the manner in which cells produce MMPs and ECMs may enable the creation of a desired tissue type, i.e. effect repair, or the prevention of tissue invasion (e.g. metastasis). The aim of this project was to determine if culturing fibroblasts on grooved topography altered collagen deposition or MMP production. Human fibroblasts were seeded on planar or grooved polycaprolactone substrates (grooves were 12.5 μm wide with varying depths of 240 nm, 540 nm or 2300 nm). Cell behaviour and collagen production were studied using fluorescence microscopy and the spent culture medium was assessed using gel zymography to detect MMPs. Total collagen deposition was high on the 240 nm deep grooves, but decreased as the groove depth increased, i.e. as cell contact guidance decreased. There was an increase in gelatinase on the 2300 nm deep grooved topography and there was a difference in the temporal expression of MMP-3 observed on the planar surface compared to the 540 nm and 2300 nm topographies. These results show that topography can alter collagen and MMP production. A fuller understanding of these processes may permit the design of surfaces tailored to tissue regeneration e.g. tendon repair.

  3. NMR studies of DNA oligomers and their interactions with minor groove binding ligands

    Energy Technology Data Exchange (ETDEWEB)

    Fagan, Patricia A. [Univ. of California, Berkeley, CA (United States). Dept. of Chemistry

    1996-05-01

    The cationic peptide ligands distamycin and netropsin bind noncovalently to the minor groove of DNA. The binding site, orientation, stoichiometry, and qualitative affinity of distamycin binding to several short DNA oligomers were investigated by NMR spectroscopy. The oligomers studied contain A,T-rich or I,C-rich binding sites, where I = 2-desaminodeoxyguanosine. I•C base pairs are functional analogs of A•T base pairs in the minor groove. The different behaviors exhibited by distamycin and netropsin binding to various DNA sequences suggested that these ligands are sensitive probes of DNA structure. For sites of five or more base pairs, distamycin can form 1:1 or 2:1 ligand:DNA complexes. Cooperativity in distamycin binding is low in sites such as AAAAA which has narrow minor grooves, and is higher in sites with wider minor grooves such as ATATAT. The distamycin binding and base pair opening lifetimes of I,C-containing DNA oligomers suggest that the I,C minor groove is structurally different from the A,T minor groove. Molecules which direct chemistry to a specific DNA sequence could be used as antiviral compounds, diagnostic probes, or molecular biology tools. The author studied two ligands in which reactive groups were tethered to a distamycin to increase the sequence specificity of the reactive agent.

  4. Measurement of sheath thickness by lining out grooves in the Hall-type stationary plasma thrusters

    International Nuclear Information System (INIS)

    Yu Daren; Wu Zhiwen; Ning Zhongxi; Wang Xiaogang

    2007-01-01

    Using grooves created along the axial direction of the discharge channel, a method for measuring sheath thickness in Hall-type stationary plasma thrusters has been developed. By distorting the wall surface using these grooves, it is possible to numerically study the effect of the wall surface on the sheath and near wall conductivity. Monte Carlo method is applied to calculate the electron temperature variation with different groove depths. The electron dynamic process in the plasma is described by a test particle method with the electron randomly entering the sheath from the discharge channel and being reflected back. Numerical results show that the reflected electron temperature is hardly affected by the wall surface if the groove depth is much less than the sheath thickness. On the other hand, the reflected electron temperature increases if the groove depth is much greater than the sheath thickness. The reflected electron temperature has a sharp jump when the depth of groove is on the order of the sheath thickness. The simulation is repeated with different sheath thicknesses and the results are the same. Therefore, a diagnosis mean of the sheath thickness can be developed based on the method. Also the simulation results are in accord with the experimental data. Besides, the measurement method may be applicable to other plasma device with similar orthogonal steady state electrical and magnetic fields

  5. Fabrication of micro-lenticular patterns using WEDM-grooving and electrolytic polishing

    Science.gov (United States)

    Park, Jong Wuk; Song, Ki Young; Chung, Do Kwan; Chu, Chong Nam

    2013-12-01

    Lenticular pattern panels have been used for displaying 3D effects and their precise fabrication methods have attracted great attention. In this study, we present a novel fabrication method for lenticular patterns on a stainless steel mold (AISI 304). The fabrication process was composed of two steps. First, the lenticular shape groove was machined by wire-electrical discharge machining (EDM) (WEDM-grooving). In this step, EDM was adopted because it is useful for machining hard-to-cut material such as WC-Co, stainless steel and titanium, and a newly developed wire grooving system ensures highly accurate machining. Second, electrolytic polishing was carried out afterward to improve the surface quality since the machined surface resulting from the WEDM-grooving was rough. The entire fabrication processes required a single machine and deionized water only; thus, the step change time was minimized and the method was eco-friendly. Parametric tests for the WEDM-grooving conditions as well as for the proper electrolytic polishing conditions (voltage, offset and feedrate) were executed to fabricate the grooves with fine surface. Excessive electrolytic polishing conditions caused pitting and damage from the additional sparks on the surface of the mold. On the other hand, inadequate machining conditions resulted in an incomplete electrolytic polishing process. Using this multi-step process, a lenticular pattern mold with high surface quality was machined. The lenticular pattern PDMS lens was successfully produced using the stainless steel mold.

  6. Structure of a pheromone receptor-associated MHC molecule with an open and empty groove.

    Directory of Open Access Journals (Sweden)

    2005-08-01

    Full Text Available Neurons in the murine vomeronasal organ (VNO express a family of class Ib major histocompatibility complex (MHC proteins (M10s that interact with the V2R class of VNO receptors. This interaction may play a direct role in the detection of pheromonal cues that initiate reproductive and territorial behaviors. The crystal structure of M10.5, an M10 family member, is similar to that of classical MHC molecules. However, the M10.5 counterpart of the MHC peptide-binding groove is open and unoccupied, revealing the first structure of an empty class I MHC molecule. Similar to empty MHC molecules, but unlike peptide-filled MHC proteins and non-peptide-binding MHC homologs, M10.5 is thermally unstable, suggesting that its groove is normally occupied. However, M10.5 does not bind endogenous peptides when expressed in mammalian cells or when offered a mixture of class I-binding peptides. The F pocket side of the M10.5 groove is open, suggesting that ligands larger than 8-10-mer class I-binding peptides could fit by extending out of the groove. Moreover, variable residues point up from the groove helices, rather than toward the groove as in classical MHC structures. These data suggest that M10s are unlikely to provide specific recognition of class I MHC-binding peptides, but are consistent with binding to other ligands, including proteins such as the V2Rs.

  7. Imaging of head and neck tumors -- methods: CT, spiral-CT, multislice-spiral-CT

    Energy Technology Data Exchange (ETDEWEB)

    Baum, Ulrich E-mail: baum@idr.med.uni-erlangen.de; Greess, Holger; Lell, Michael; Noemayr, Anton; Lenz, Martin

    2000-03-01

    Spiral-CT is standard for imaging neck tumors. In correspondence with other groups we routinely use spiral-CT with thin slices (3 mm), a pitch of 1.3-1.5 and an overlapping reconstruction increment (2-3 mm). In patients with dental fillings a short additional spiral parallel to the corpus of the mandible reduces artifacts behind the dental arches and improves the diagnostic value of CT. For the assessment of the base of the skull, the orbital floor, the palate and paranasal sinuses an additional examination in the coronal plane is helpful. Secondary coronal reconstructions of axial scans are helpful in the evaluation of the crossing of the midline by small tumors of the tongue base or palate. For an optimal vascular or tissue contrast a sufficient volume of contrast medium and a start delay greater than 70-80 s are necessary. In our opinion the best results can be achieved with a volume of 150 ml, a flow of 2.5 ml/s and a start delay of 80 s. Dynamic enhanced CT is only necessary in some special cases. There is clear indication for dynamic enhanced CT where a glomus tumor is suspected. Additional functional CT imaging during i-phonation and/or Valsalva's maneuver are of great importance to prove vocal cords mobility. Therefore, imaging during i-phonation is an elemental part of every thorough examination of the hypopharynx and larynx region. Multislice-spiral-CT allows almost isotropic imaging of the head and neck region and improves the assessment of tumor spread and lymph node metastases in arbitrary oblique planes. Thin structures (the base of the skull, the orbital floor, the hard palate) as well as the floor of the mouth can be evaluated sufficiently with multiplanar reformations. Usually, additional coronal scanning is not necessary with multislice-spiral-CT. Multislice-spiral-CT is especially advantageous in defining the critical relationships of tumor and lymph node metastases and for functional imaging of the hypopharynx and larynx not only in the

  8. Imaging of head and neck tumors -- methods: CT, spiral-CT, multislice-spiral-CT

    International Nuclear Information System (INIS)

    Baum, Ulrich; Greess, Holger; Lell, Michael; Noemayr, Anton; Lenz, Martin

    2000-01-01

    Spiral-CT is standard for imaging neck tumors. In correspondence with other groups we routinely use spiral-CT with thin slices (3 mm), a pitch of 1.3-1.5 and an overlapping reconstruction increment (2-3 mm). In patients with dental fillings a short additional spiral parallel to the corpus of the mandible reduces artifacts behind the dental arches and improves the diagnostic value of CT. For the assessment of the base of the skull, the orbital floor, the palate and paranasal sinuses an additional examination in the coronal plane is helpful. Secondary coronal reconstructions of axial scans are helpful in the evaluation of the crossing of the midline by small tumors of the tongue base or palate. For an optimal vascular or tissue contrast a sufficient volume of contrast medium and a start delay greater than 70-80 s are necessary. In our opinion the best results can be achieved with a volume of 150 ml, a flow of 2.5 ml/s and a start delay of 80 s. Dynamic enhanced CT is only necessary in some special cases. There is clear indication for dynamic enhanced CT where a glomus tumor is suspected. Additional functional CT imaging during i-phonation and/or Valsalva's maneuver are of great importance to prove vocal cords mobility. Therefore, imaging during i-phonation is an elemental part of every thorough examination of the hypopharynx and larynx region. Multislice-spiral-CT allows almost isotropic imaging of the head and neck region and improves the assessment of tumor spread and lymph node metastases in arbitrary oblique planes. Thin structures (the base of the skull, the orbital floor, the hard palate) as well as the floor of the mouth can be evaluated sufficiently with multiplanar reformations. Usually, additional coronal scanning is not necessary with multislice-spiral-CT. Multislice-spiral-CT is especially advantageous in defining the critical relationships of tumor and lymph node metastases and for functional imaging of the hypopharynx and larynx not only in the

  9. A Method to Automate Identification of Spiral Arms in Galaxies

    Science.gov (United States)

    Lacey, Christina K.; Mercer, K.

    2014-01-01

    We present our preliminary results in identifying the spiral arms of NGC 6946 using a nearest-neighbors analysis. NGC 6946 is grand design spiral galaxy with well-defined arms. The spiral arms were previously identified in an Hα image and traced out by Matonick, D. et al., ApJS, 113, 333, (1997) by visual inspection. We want to develop a computer algorithm that will identify the spiral arms automatically. Once the spiral arms have been found digitally, we can use this information to compare the spiral arms with the locations of compact objects such as supernova remnants and perform statistical tests, for example, to determine if the supernova remnants are associated with the spiral arms. We are using the publicly available program PyFITS, a development project of the Science Software Branch at the Space Telescope Science Institute (STScI) that is available for software download from STScI, to perform a computer-based image analysis. We have written python macros that interact with the already written image manipulation and display features of PyFITS to perform the image analysis and implement a nearest-neighbors algorithm to identify and link the centers of the high emission regions from the spiral arm regions. Our code currently identifies the centers of the high emission regions, but more work is needed to link up these sites and draw out the spiral arms. Future work includes improving the code to better identify spiral arms and converting the code to work on the Astropy, a community-developed core Python package for Astronomy (Robitaille, T. P., et al. A&A 558, A33, 2013).

  10. Thrust Stand Characterization of the NASA Evolutionary Xenon Thruster (NEXT)

    Science.gov (United States)

    Diamant, Kevin D.; Pollard, James E.; Crofton, Mark W.; Patterson, Michael J.; Soulas, George C.

    2010-01-01

    Direct thrust measurements have been made on the NASA Evolutionary Xenon Thruster (NEXT) ion engine using a standard pendulum style thrust stand constructed specifically for this application. Values have been obtained for the full 40-level throttle table, as well as for a few off-nominal operating conditions. Measurements differ from the nominal NASA throttle table 10 (TT10) values by 3.1 percent at most, while at 30 throttle levels (TLs) the difference is less than 2.0 percent. When measurements are compared to TT10 values that have been corrected using ion beam current density and charge state data obtained at The Aerospace Corporation, they differ by 1.2 percent at most, and by 1.0 percent or less at 37 TLs. Thrust correction factors calculated from direct thrust measurements and from The Aerospace Corporation s plume data agree to within measurement error for all but one TL. Thrust due to cold flow and "discharge only" operation has been measured, and analytical expressions are presented which accurately predict thrust based on thermal thrust generation mechanisms.

  11. Electromagnetic, flow and thermal study of a miniature planar spiral transformer with planar, spiral windings

    Directory of Open Access Journals (Sweden)

    J. B. DUMITRU

    2014-04-01

    Full Text Available This paper presents mathematical modeling and numerical simulation results for a miniature, planar, spiral transformer (MPST fabricated in micro-electromechanical MEMS technology. When the MPST is magnetic nanofluid cored, magnetization body forces occur, entraining it into a complex flow. This particular MPST design is then compared with other competing solutions concerning the lumped (circuit parameters. Finally, the heat transfer problem is solved for different electromagnetic working conditions to assess the thermal loads inside the MPST.

  12. Spiral model pilot project information model

    Science.gov (United States)

    1991-01-01

    The objective was an evaluation of the Spiral Model (SM) development approach to allow NASA Marshall to develop an experience base of that software management methodology. A discussion is presented of the Information Model (IM) that was used as part of the SM methodology. A key concept of the SM is the establishment of an IM to be used by management to track the progress of a project. The IM is the set of metrics that is to be measured and reported throughout the life of the project. These metrics measure both the product and the process to ensure the quality of the final delivery item and to ensure the project met programmatic guidelines. The beauty of the SM, along with the IM, is the ability to measure not only the correctness of the specification and implementation of the requirements but to also obtain a measure of customer satisfaction.

  13. Characteristics of elliptical vibration cutting in micro-V grooving with variations in the elliptical cutting locus and excitation frequency

    International Nuclear Information System (INIS)

    Kim, Gi Dae; Loh, Byoung Gook

    2008-01-01

    The characteristics of elliptical vibration cutting (EVC) in micro-V grooving in connection with variations of the elliptical cutting locus and the excitation frequency have been investigated with a cutting device consisting of orthogonally connected dual piezoelectric actuators. The elliptical cutting locus was modulated by changing the magnitude and phase difference of harmonic voltages supplied to the piezoelectric actuators, and the maximum excitation frequency used for EVC was 19 kHz. It was found that cyclic breaking of the contact between the tool and the workpiece is a pre-requisite for the merits of the EVC process to be realized. An index termed non-contact index (NCI) involving the vibration amplitude of the elliptical locus, the feed speed and the excitation frequency was defined to determine the existence of cyclic breaking of the contact under a given EVC condition. The surface roughness in the feed direction showed a tendency to increase with the vibration amplitude in the thrust direction and the square of the feed speed, and to decrease with the square of the vibration amplitude in the cutting direction and the square of the excitation frequency. The variation in the cutting resistance was in good agreement with the CR trend curve representing the contact ratio between the tool and the workpiece in EVC; in the EVC process involving breaking of the contact, marked decrease in the cutting force occurred at higher values of CR at which either slight increase in the excitation frequency or in the vibration amplitude results in significant decrease in the cutting force. Reduction in the cutting force preferably contributed to the improvement of machining quality of the micro features by inhibiting burr formation

  14. Dual-action gas thrust bearing for improving load capacity

    Science.gov (United States)

    Etsion, I.

    1976-01-01

    The principle of utilizing hydrodynamic effects in diverging films to improve the load carrying capacity in gas thrust bearings is discussed. A new concept of a dual action bearing based on that principle is described and analyzed. The potential of the new bearing is demonstrated both analytically for an infinitely long slider and by numerical solution for a flat sector shaped thrust bearing. It is shown that the dual action bearing can extend substantially the range of load carrying capacity in gas lubricated thrust bearings and can improve their efficiency.

  15. Early Cenozoic Multiple Thrust in the Tibetan Plateau

    OpenAIRE

    Zhenhan Wu; Peisheng Ye; Patrick J. Barosh; Daogong Hu; Lu Lu

    2013-01-01

    Recently completed regional geological mapping at a scale of 1 : 250,000 or larger across all of the Tibetan Plateau coupled with deep seismic surveys reveals for the first time a comprehensive depiction of the major early Cenozoic thrust systems resulting from the northward subduction of the Indian Continental Plate. These systems define a series of overlapping north-dipping thrust sheets that thickened the Tibetan crust and lead to the rise of the plateau. The few south-dipping thrusts pres...

  16. Processing fine stainless-steel slag using spiral concentration.

    Science.gov (United States)

    Wolfe, Eric R; Klima, Mark S

    2008-04-01

    In this study, the effectiveness of spiral concentration to process a fine (-1 mm) stainless-steel slag was evaluated. Specifically, testing was conducted to determine the feasibility of producing a high metal content stainless steel product and a low metal content aggregate product. This involved investigating a key operating variable for both five-and seven-turn spiral concentrators. The raw slag and spiral products were characterized to determine their respective size and metal distributions. Separation testing was carried out using the two full-scale spiral concentrators to evaluate the effects of feed solids concentration on spiral performance at solids feed rates ranging from 15 to 30 kg/min. The results indicated that under certain conditions, a high-quality metal fraction could be produced. For example, using the five-turn spiral, a product containing 95% metal was obtained at a low metal recovery. Both spirals were ineffective at concentrating the aggregate fraction. Overall, the feed solids concentration did not significantly affect the quality or recoveries of the products, particularly for feed solids concentrations less than 35% by weight. In order to improve the metal recoveries and to produce a low-metal aggregate material, reprocessing of the product streams and/or additional liberation of the raw slag would be required.

  17. Pancreatic adenocarcinoma : usefulness of two and three phase spiral CT

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kyeong Ah; Kim, Hyung Soo; Park, Cheol Min; Cha, In Ho [Korea Univ. College of Medicine, Seoul (Korea, Republic of)

    1996-10-01

    To evaluate the efficacy of each phases in two and three phase spiral CT in the detection of pancreatic adenocarcinoma. Two phase spiral CT images of 18 patients and three phase spiral CT images of 12 patients with pathologically-proven pancreatic ductal adenocarcinoma were retrospectively compared. Using a single spiral scan, images of early and delayed phases were obtained at 43 seconds and 2{approx}3minutes respectively initiating the after administration of 100-120cc of contrast material (2{approx}3cc/sec), Images of arterial, portal and delayed phases were also obtained at 25 and 60 seconds, and 3{approx}4minutes, respectively, by the use of a double spiral scan. CT scans were performed with 10mm collimation at 1:1 pitch table speed. Contrast between the tumor and adjacent pancreatic parenchyma were compared and graded and enhancement pattern of the tumor were analysed together. In 12 patients (66.7%), images of the early phase were superior to those of the delayed phase. images of the portal phase were superior to those of the arterial phase. Enhancement of tumor was seen in four patients;all tumors were less than 3cm in size. The early phase of two phase spiral CT is superior to the delayed phase and the portal phase of three phase spiral CT is superior to the arterial phase. Both arterial and portal phases are superior to the delayed phase.

  18. Spiral Antenna-Coupled Microbridge Structures for THz Application.

    Science.gov (United States)

    Gou, Jun; Zhang, Tian; Wang, Jun; Jiang, Yadong

    2017-12-01

    Bolometer sensor is a good candidate for THz imaging due to its compact system, low cost, and wideband operation. Based on infrared microbolometer structures, two kinds of antenna-coupled microbridge structures are proposed with different spiral antennas: spiral antenna on support layer and spiral antenna with extended legs. Aiming at applications in detection and imaging, simulations are carried out mainly for optimized absorption at 2.52 THz, which is the radiation frequency of far-infrared CO 2 lasers. The effects of rotation angle, line width, and spacing of the spiral antenna on THz wave absorption of microbridge structures are discussed. Spiral antenna, with extended legs, is a good solution for high absorption rate at low absorption frequency and can be used as electrode lead simultaneously for simplified manufacturing process. A spiral antenna-coupled microbridge structure with an absorption rate of more than 75% at 2.52 THz is achieved by optimizing the structure parameters. This research demonstrates the use of different spiral antennas for enhanced and tunable THz absorption of microbridge structures and provides an effective way to fabricate THz microbolometer detectors with great potential in the application of real-time THz imaging.

  19. Evaluation of erythrocyte flow at a bearing gap in a hydrodynamically levitated centrifugal blood pump.

    Science.gov (United States)

    Murashige, Tomotaka; Kosaka, Ryo; Sakota, Daisuke; Nishida, Masahiro; Kawaguchi, Yasuo; Yamane, Takashi; Maruyama, Osamu

    2015-01-01

    We have developed a hydrodynamically levitated centrifugal blood pump for extracorporeal circulatory support. In the blood pump, a spiral groove bearing was adopted for a thrust bearing. In the spiral groove bearing, separation of erythrocytes and plasma by plasma skimming has been postulated to occur. However, it is not clarified that plasma skimming occurs in a spiral groove bearing. The purpose of this study is to verify whether plasma skimming occurs in the spiral groove bearing of a hydrodynamically levitated centrifugal blood pump. For evaluation of plasma skimming in the spiral groove bearing, an impeller levitation performance test using a laser focus displacement meter and a microscopic visualization test of erythrocyte flow using a high-speed microscope were conducted. Bovine blood diluted with autologous plasma to adjust hematocrit to 1.0% was used as a working fluid. Hematocrit on the ridge region in the spiral groove bearing was estimated using image analysis. As a result, hematocrits on the ridge region with gaps of 45 μm, 31 μm, and 25 μm were calculated as 1.0%, 0.6%, and 0.3%, respectively. Maximum skimming efficiency in this study was calculated as 70% with a gap of 25 μm. We confirmed that separation of erythrocyte and plasma occurred in the spiral groove bearing with decrease in bearing gap in a hydrodynamically levitated centrifugal blood pump.

  20. The impact of postoperative supraclavicular radiotherapy on tracheoesophageal groove lymph node metastasis in esophageal carcinoma

    International Nuclear Information System (INIS)

    Qian Pudong; Lu Jinchen; Mei Zeru; Zhu Jun

    2005-01-01

    Objective: To evaluate the prognostic factors of tracheoesophageal groove lymph node (TEGLN) metastasis in postoperative esophageal carcinoma. Methods: From January 1996 to December 1997, 101 postoperative cervical and thoracic esophageal carcinoma patients proved absence from tracheoesophageal groove lymph node (TEGIAN) metastasis before and after operation by physical examination and computer tomography examination were entered into this study. The patients were divided into three groups according to the treatment of supraclavicular region: no prophylactic radiotherapy (group A-, 30 patients); prophylactic radiotherapy with local dose < 45 Gy (Group B-, 71 patients); and prophylactic radiotherapy with local dose ≥45 Gy (Group C-, 19 patients). Radiotherapy was delivered by cobalt- 60 or 6 MV X-ray with the prescribed dose normalized to the point of tracheoesophageal groove, i. e, 5 cm in depth. The tracheoesophageal groove lymph node metastasis after treatment was observed. Results: The incidence of tracheoesophageal groove lymph node metastasis was 20% (6/30), 9.6% (5/71) and 0% (0/19) in groups A, B and C. Univariate analysis showed that there was significant difference of TEGLN metastasis between groups A and C only (P=0.039), but higher dose to supraclavicular region tended to lower the incidence of TEGLN metastasis. Multivariate analysis showed that only prophylactic radiotherapy to the supraclavicular region was independent prognostic factor for TEGLN metastasis (P=0.037). Gender, primary tumor site and pathological stage had no significant impact on TEGLN metastasis. Conclusions: Postoperative prophylactic supraclavicular region irradiation can lower the incidence of tracheoesophageal groove lymph node metastasis in esophageal carcinoma. Radiotherapy dose should not be less than 45 Gy and should be routinely normalized to a point 5 cm deep in the tracheoesophageal groove. (authors)

  1. A Software Development Simulation Model of a Spiral Process

    Science.gov (United States)

    Mizell, Carolyn; Malone, Linda

    2007-01-01

    There is a need for simulation models of software development processes other than the waterfall because processes such as spiral development are becoming more and more popular. The use of a spiral process can make the inherently difficult job of cost and schedule estimation even more challenging due to its evolutionary nature, but this allows for a more flexible process that can better meet customers' needs. This paper will present a discrete event simulation model of spiral development that can be used to analyze cost and schedule effects of using such a process in comparison to a waterfall process.

  2. Fabrication techniques of X-ray spiral zone plates

    International Nuclear Information System (INIS)

    Gao Nan; Zhu Xiaoli; Li Hailiang; Xie Changqing

    2010-01-01

    The techniques to make X-ray spiral zone plates using electron beam and X-ray lithography were studied. A master mask was fabricated on polyimide membrane by E-beam lithography and micro-electroplating. Spiral zone plates were efficiently replicated by X-ray lithography and micro-electroplating. By combining the techniques, spiral zone plates at 1 keV were successfully fabricate. With an outermost zone width of the 200 nm, and the gold absorbers thickness of 700 nm, the high quality zone plates can be used for X-ray phase contrast microscopy.(authors)

  3. Comments on H. Arp 'The persistent problem of spiral galaxies'

    International Nuclear Information System (INIS)

    Alfven, H.

    1987-04-01

    In his paper 'The persistent problem of Spiral Galaxies' H. Arp criticises the standard theory of spiral galaxies and demonstrates that introduction of plasma theory is necessary in order to understand the structure of spiral galaxies. In the present paper arguments are given in support of Arp's theory and suggestions are made how Arp's ideas should be developed. An important result of Arp's new approach is that there is no convincing argument for the belief that there is a 'missing mass'. This is important from a cosmological point of view. (author)

  4. Harmonic oscillator in an elastic medium with a spiral dislocation

    Science.gov (United States)

    Maia, A. V. D. M.; Bakke, K.

    2018-02-01

    We investigate the behaviour of a two-dimensional harmonic oscillator in an elastic medium that possesses a spiral dislocation (an edge dislocation). We show that the Schrödinger equation for harmonic oscillator in the presence of a spiral dislocation can be solved analytically. Further, we discuss the effects of this topological defect on the confinement to a hard-wall confining potential. In both cases, we analyse if the effects of the topology of the spiral dislocation gives rise to an Aharonov-Bohm-type effect for bound states.

  5. Improved Rhenium Thrust Chambers for In-Space Propulsion Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Radiation-cooled, bipropellant thrust chambers are being considered for the ascent/descent engines and reaction control systems (RCS) for future NASA missions such...

  6. Optimal Thrust Vectoring for an Annular Aerospike Nozzle, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Recent success of an annular aerospike flight test by NASA Dryden has prompted keen interest in providing thrust vector capability to the annular aerospike nozzle...

  7. Low Thrust Trajectory Optimization in Cislunar and Translunar Space

    Data.gov (United States)

    National Aeronautics and Space Administration — The goal of this project is to advance the state of the art with regard to low thrust trajectory optimization in 3-body and 4-body force models, specifically in...

  8. Optimal Thrust Vectoring for an Annular Aerospike Nozzle Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Recent success of an annular aerospike flight test by NASA Dryden has prompted keen interest in providing thrust vector capability to the annular aerospike nozzle...

  9. High Performance Methane Thrust Chamber (HPMTC), Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — ORBITEC proposes to develop a High-Performance Methane Thrust Chamber (HPMRE) to meet the demands of advanced chemical propulsion systems for deep-space mission...

  10. Nitrous Oxide Liquid Injection Thrust Vector Control System Testing Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A Nitrous Oxide-fed Liquid Thrust Vector Control system is proposed as an efficient method for vehicle attitude control during powered flight. Pulled from a N2O main...

  11. Evaluation of rotating, incompressibly lubricated, pressurized thrust bearings

    Science.gov (United States)

    Fleming, D. P.

    1971-01-01

    Program evaluates a series hybrid, fluid film ball bearing consisting of an orifice compensated pressurized thrust bearing in conjunction with a self-acting journal bearing. Oil viscosities corresponding to experimentally measured ball bearing outer-race temperatures were used.

  12. Design and Analysis of an Electromagnetic Thrust Bearing

    Science.gov (United States)

    Banerjee, Bibhuti; Rao, Dantam K.

    1996-01-01

    A double-acting electromagnetic thrust bearing is normally used to counter the axial loads in many rotating machines that employ magnetic bearings. It essentially consists of an actuator and drive electronics. Existing thrust bearing design programs are based on several assumptions. These assumptions, however, are often violated in practice. For example, no distinction is made between maximum external loads and maximum bearing forces, which are assumed to be identical. Furthermore, it is assumed that the maximum flux density in the air gap occurs at the nominal gap position of the thrust runner. The purpose of this paper is to present a clear theoretical basis for the design of the electromagnetic thrust bearing which obviates such assumptions.

  13. Optimal Thrust Vectoring for an Annular Aerospike Nozzle, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Recent success of an annular aerospike flight test by NASA Dryden has prompted keen interest in providing thrust vector capability to the annular aerospike nozzle...

  14. Thrust generation and wake structure for flow across a pitching ...

    Indian Academy of Sciences (India)

    The generation of thrust by a flapping airfoil depends upon the wake structure behind the ... a wake vortex pattern causes generation of net thrust on the airfoil. ..... Y. 1. 1.5. 2. -0.6. -0.2. 0.2. 0.6. X=0.5. X=1.0. X=1.5. (a). Figure 5. Mean and r.m.s. velocity profiles for three different streamwise stations, at k =1.82. (a) Mean.

  15. The calculation of the thrust of a rocket motor

    Directory of Open Access Journals (Sweden)

    J. H. Knoetze

    1993-07-01

    Full Text Available Traditionally the thrust of a rocket motor is calculated by first calculating the thrust coefficient and then multiplying it by the product of the throat area and pressure. The thrust coefficient is calculated using a standard gas dynamics equation. This equation assumes that the combustion products are a single component, non-reacting ideal gas and that the flow through the nozzle is isentropic. The thrust coefficient is a function of the ratio of specific heats, y, the area ratio of the nozzle and the motor and ambient pressures. Standard methods exist for calculating the tosses due to deviations from the assumed flow. The combustion products of modern composite propellants contain a significant portion of condensed species (primarily A1₂O₃, while the composition of the combustion products changes continuously as the products move throught the nozzle. Some uncertainty therefore exists with regard to which value of y to use and how to handle the condensed species. The assumption o f an ideat, non-reacting gas can be el iminated hy as.mming the process to he isentropic and to calculate the thrust hy using the thermodynamic state and composition of the combustion products in the motor and nozzle exit. This can be achieved by using any of the standard thermochemistry programs available in the rocket industry. It is thus possible to use the results of a standard thermochemistry program directly in an alternative method for calculating thrust. Using this method only the mass flow rate (which is a function of pressure, throat area and effective caracteristic velocity and the results from the thermochemistry program are needed to calculate the thrust. The advantages of the alternative method are illustrated by comparing the results of the two methods with a measured thrust curve.

  16. 8 . TOTAL THRUST ON EARTH-RETAlNING STRUCTURES DUE ...

    African Journals Online (AJOL)

    Terz.aghi and Bowles recommended to double the lateral stress value a xJ for the case of a uniform strip load [I]. Hence: (13). Table 2 list values of the influence factor m3 for various ratiQS of n = x0 / b and m = H /b . C. Total Thrust For Stratified Soils due to Point. Load. Total thrust on earth-retaining structure due to point.

  17. Quadcopter Attitude and Thrust Simulation Based on Simulink Platform

    Directory of Open Access Journals (Sweden)

    Endrowednes Kuantama

    2015-12-01

    Full Text Available Orientation of quadcopter axes relative to reference line direction of motion will result in attitude and every movement is controlled regulated by each rotor’s thrust. Mathematical equation based on Euler formula and 3D simulation using Matlab/Simulink software platform are used to model quadcopter movement. Change of attitude, position and thrust of each rotor can be seen through this simulation movement.

  18. What musicians do to induce the sensation of groove in simple and complex melodies, and how listeners perceive it

    Directory of Open Access Journals (Sweden)

    Guy eMadison

    2014-08-01

    Full Text Available Groove is the experience of wanting to move when hearing music, such as snapping fingers or tapping feet. This is a central aspect of much music, in particular of music intended for dancing. While previous research has found considerable consistency in ratings of groove across individuals, it remains unclear how groove is induced, that is, what are the physical properties of the acoustic signal that differ between more and less groove-inducing versions. Here, we examined this issue with a performance experiment, in which 4 musicians performed 6 simple and 6 complex melodies in two conditions with the intention of minimizing and maximizing groove. Analyses of rhythmical and temporal properties from the performances demonstrated some general effects. For example, more groove was associated with more notes on faster metrical levels and syncopation, and less groove was associated with deadpan timing and destruction of the regular pulse. We did not observe that deviations from the metrical grid (i.e. micro-timing were a predictor of groove. A listener experiment confirmed that the musicians’ manipulations had the intended effects on the experience of groove. A Brunswikian lens model was applied, which estimates the performer-perceiver communication across the two experiments. It showed that the communication achievement for simple melodies was 0.62, and that the matching of performers’ and listeners’ use of 9 rhythmical cues was 0.83. For complex melodies with an already high level of groove, the corresponding values were 0.39 and 0.34, showing that it was much more difficult to take out groove from musical structures designed to induce groove.

  19. An in vitro assessment of circumferential grooves on the retention of cement-retained implant-supported crowns.

    Science.gov (United States)

    Lewinstein, Israel; Block, Liat; Lehr, Zachi; Ormianer, Zeev; Matalon, Shlomo

    2011-12-01

    Crowns cemented on short implant abutments may have insufficient retention. The purpose of this study was to evaluate the effect of circumferential grooves on the retention of cemented cast copings on implant abutments. Sixty similarly-shaped implant abutments were divided into 4 groups (n=15): without grooves, with 1 groove, with 2 grooves, and with 3 grooves. Fifteen identical NiCr cast copings were prepared to fit all 60 abutments. The castings were cemented to each group of abutments with a noneugenol provisional cement (Tempbond NE) and a zinc phosphate cement (Harvard). After thermal cycling and storage for 6 days in a water bath, retention tests were conducted with a tensile testing machine (Instron) (5 mm/min) and retentive forces were recorded. Data were subjected to 1 way-ANOVA, Tukey's (HSD) test, and repeated measures ANOVA (α=.05). For the noneugenol temporary cement, group retention values were increased according to the number of grooves (Pcement, the first groove increased the retention by approximately 60% (Pcement than the provisional cement. The influence of the grooves depended on the type of cement used (PCement remnants were found primarily on the castings for provisional cement and for the plain abutments cemented with zinc phosphate cement. Remnants were found primarily on the abutments for the grooved abutments cemented with zinc phosphate cement. The addition of circumferential grooves to implant abutments increased the retention of cement-retained castings. For zinc phosphate cement, 1 groove was as effective as several, whereas for the provisional cement, the retention increased gradually with additional grooves. Copyright © 2011 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

  20. A test for the minimum scale of grooving on the Amatrice and Norcia earthquakes

    Science.gov (United States)

    Okamoto, K.; Brodsky, E. E.; Billi, A.

    2017-12-01

    As stress builds up along a fault, elastic strain energy builds until it cannot be accommodated by small-scale ductile deformation and then the fault brittlely fails. This brittle failure is associated with the grooving process that causes slickensides along fault planes. Therefore the scale at which slickensides disappear could be geological evidence of earthquake nucleation. Past studies found the minimum scale of grooving, however the studied fault surfaces were not exposed by recent earthquakes. These measurements could have been a product of chemical or mechanical weathering. On August 24th and October 30th of 2016, MW 6.0 and 6.5 earthquakes shook central Italy. The earthquakes caused decimeter to meter scale fault scarps along the Mt. Vettoretto Fault. Here, we analyze samples of a scarp using white light interferometry in order to determine if the minimum scale of grooving is present. Results suggest that grooving begins around 100 μm for these samples, which is consistent with previous findings of faults without any direct evidence of earthquakes. The measurement is also consistent with typical values of the frictional weakening distance Dc, which also is associated with a transition between ductile and brittle behavior. The measurements show that the minimum scale of grooving is a useful measure of the behavior of faults.

  1. Transverse grooved artefacts from southwestern Asia and northern Eurasia: Common traits and the reconstruction of function

    Directory of Open Access Journals (Sweden)

    Irina Usacheva

    2016-10-01

    Full Text Available Transverse grooved artefacts (TGA appeared as a new cultural element in Mesolithic-Proto-Neolithic sites in southwestern Asia. We know of similar artefacts from northern Africa. Hundreds of TGA have also been found in northern Eurasia. Some common traits were found in specimens from far apart territories, such as the non-abrasive heat-resistant nature of the raw materials, specificity of fragmentation without any signs of physical impact, the standard size of the grooves, association with a specific type of landscape, the similar economic level of the societies with which the items are associated, and use-wear marks in the grooves. Based on these regularities we can speak of a single main function for these artefacts which support the earlier reconstruction of R.L. and R.S. Solecki, suggesting that grooved stones were used for straightening cane and reed shafts under heating. Other evidence and traces that have been identified on the surface of TGA outside the groove could be associated with a variety of additional functions.

  2. Research on fatigue behavior and residual stress of large-scale cruciform welding joint with groove

    International Nuclear Information System (INIS)

    Zhao, Xiaohui; Liu, Yu; Liu, Yong; Gao, Yuan

    2014-01-01

    Highlights: • The fatigue behavior of the large-scale cruciform welding joint with groove was studied. • The longitudinal residual stress of the large-scale cruciform welding joint was tested by contour method. • The fatigue fracture mechanism of the large-scale cruciform welding joint with groove was analyzed. - Abstract: Fatigue fracture behavior of the 30 mm thick Q460C-Z steel cruciform welded joint with groove was investigated. The fatigue test results indicated that fatigue strength of 30 mm thick Q460C-Z steel cruciform welded joint with groove can reach fatigue level of 80 MPa (FAT80). Fatigue crack source of the failure specimen initiated from weld toe. Meanwhile, the microcrack was also found in the fusion zones of the fatigue failure specimen, which was caused by weld quality and weld metal integrity resulting from the multi-pass welds. Two-dimensional map of the longitudinal residual stress of 30 mm thick Q460C-Z steel cruciform welded joint with groove was obtained by using the contour method. The stress nephogram of Two-dimensional map indicated that longitudinal residual stress in the welding center is the largest

  3. CFD and Experimental Analysis of a Falling Film outside Smooth and Helically Grooved Tubes

    Directory of Open Access Journals (Sweden)

    Cenk Onan

    2014-08-01

    Full Text Available Simultaneous heat and mass transfer are investigated in a falling film outside grooved and smooth tubes. A numerical analysis of the helically trapezoidal-grooved and reference smooth tube was performed in the computational fluid dynamics program “Ansys Fluent 14.” The three-dimensional model drawings in the x, y, and z coordinates are used, and the effects of the falling film outside the helically grooved tube on the surface temperature and surface heat transfer coefficient are determined. The average surface temperature, heat transfer coefficient, and Nu values are determined experimentally for a constant heat flux. An uncertainty analysis and Nu correlation for the grooved tube are also provided in this study. The Reynolds number varied between 50 and 350 for the falling film and between 1500 and 3500 for air. Using a computational fluid dynamics (CFD analysis for the reference smooth tube, the experimental results are validated within 2–12% difference. The experimental results are also within 6–13% of the grooved tubes.

  4. Role of Marangoni instability in fabrication of axially and internally grooved hollow fiber membranes.

    Science.gov (United States)

    Yin, Jun; Coutris, Nicole; Huang, Yong

    2010-11-16

    Hollow fiber membranes (HFMs) are extensively used in different industrial applications. Under some controlled fabrication conditions, axially aligned grooves can be formed on the HFM inner surface during typical immersion precipitation-based phase inversion fabrication processes. Such grooved HFMs are found to be promising for nerve repair and regeneration. The axially aligned grooves appearing on the inner surface of the membrane are considered as hydrodynamic instability patterns. During the immersion precipitation process, a transfer of solvent takes place across the interface between a polymer solution and a nonsolvent. This solvent transfer induces gradients of interfacial tension that are considered to be the driving mechanism for Marangoni instability. The onset of the stationary instability is studied by means of a linear instability theory, and the critical and maximum wavenumbers are determined and discussed in terms of the dimensionless groups characterizing the system: viscosity ratio, diffusivity ratio, Schmidt number, crispation number, adsorption number, Marangoni number, and the polymer bulk concentration. A good agreement is found between the predicted wavelength of the most dangerous wave and the experimental groove width. Consequently, solutal Marangoni instability can explain the groove formation mechanism in HFM fabrication.

  5. Development of an equine groove model to induce metacarpophalangeal osteoarthritis: a pilot study on 6 horses.

    Directory of Open Access Journals (Sweden)

    Ugo Maninchedda

    Full Text Available The aim of this work was to develop an equine metacarpophalangeal joint model that induces osteoarthritis that is not primarily mediated by instability or inflammation. The study involved six Standardbred horses. Standardized cartilage surface damage or "grooves" were created arthroscopically on the distal dorsal aspect of the lateral and medial metacarpal condyles of a randomly chosen limb. The contralateral limb was sham operated. After 2 weeks of stall rest, horses were trotted 30 minutes every other day for 8 weeks, then evaluated for lameness and radiographed. Synovial fluid was analyzed for cytology and biomarkers. At 10 weeks post-surgery, horses were euthanized for macroscopic and histologic joint evaluation. Arthroscopic grooving allowed precise and identical damage to the cartilage of all animals. Under the controlled exercise regime, this osteoarthritis groove model displayed significant radiographic, macroscopic, and microscopic degenerative and reactive changes. Histology demonstrated consistent surgically induced grooves limited to non-calcified cartilage and accompanied by secondary adjacent cartilage lesions, chondrocyte necrosis, chondrocyte clusters, cartilage matrix softening, fissuring, mild subchondral bone inflammation, edema, and osteoblastic margination. Synovial fluid biochemistry and cytology demonstrated significantly elevated total protein without an increase in prostaglandin E2, neutrophils, or chondrocytes. This equine metacarpophalangeal groove model demonstrated that standardized non-calcified cartilage damage accompanied by exercise triggered altered osteochondral morphology and cartilage degeneration with minimal or inefficient repair and little inflammatory response. This model, if validated, would allow for assessment of disease processes and the effects of therapy.

  6. Development of an equine groove model to induce metacarpophalangeal osteoarthritis: a pilot study on 6 horses.

    Science.gov (United States)

    Maninchedda, Ugo; Lepage, Olivier M; Gangl, Monika; Hilairet, Sandrine; Remandet, Bernard; Meot, Francoise; Penarier, Geraldine; Segard, Emilie; Cortez, Pierre; Jorgensen, Christian; Steinberg, Régis

    2015-01-01

    The aim of this work was to develop an equine metacarpophalangeal joint model that induces osteoarthritis that is not primarily mediated by instability or inflammation. The study involved six Standardbred horses. Standardized cartilage surface damage or "grooves" were created arthroscopically on the distal dorsal aspect of the lateral and medial metacarpal condyles of a randomly chosen limb. The contralateral limb was sham operated. After 2 weeks of stall rest, horses were trotted 30 minutes every other day for 8 weeks, then evaluated for lameness and radiographed. Synovial fluid was analyzed for cytology and biomarkers. At 10 weeks post-surgery, horses were euthanized for macroscopic and histologic joint evaluation. Arthroscopic grooving allowed precise and identical damage to the cartilage of all animals. Under the controlled exercise regime, this osteoarthritis groove model displayed significant radiographic, macroscopic, and microscopic degenerative and reactive changes. Histology demonstrated consistent surgically induced grooves limited to non-calcified cartilage and accompanied by secondary adjacent cartilage lesions, chondrocyte necrosis, chondrocyte clusters, cartilage matrix softening, fissuring, mild subchondral bone inflammation, edema, and osteoblastic margination. Synovial fluid biochemistry and cytology demonstrated significantly elevated total protein without an increase in prostaglandin E2, neutrophils, or chondrocytes. This equine metacarpophalangeal groove model demonstrated that standardized non-calcified cartilage damage accompanied by exercise triggered altered osteochondral morphology and cartilage degeneration with minimal or inefficient repair and little inflammatory response. This model, if validated, would allow for assessment of disease processes and the effects of therapy.

  7. The thickness effects of the side-grooved CCT specimen, 1

    International Nuclear Information System (INIS)

    Machida, Kenji; Kikuchi, Masanori; Miyamoto, Hiroshi

    1987-01-01

    J IC tests were carried out on SUS 316 steel by means of the JSME R-curve method as well as the JSME stretched-zone width (SZW) method. The effect of side-grooves on the J In value at stable crack growth initiation was investigated by using CCT specimens of two thicknesses (B = 1, 2 mm). The ratio of net thickness to gross thickness was kept at 0.5. The J In values of the side-grooved CCT specimens of two thicknesses were considerably smaller than those of the 1TCT specimen. The J In value of the side-grooved specimen of 2 mm thickness was smaller than that of the standard CCT specimen. Further, as the thickness of the specimen becomes thinner, the J In value decreases. In the case of 1 mm thick CCT specimens with or without a side groove, the contraction percentage of thickness is very large so that it is not appropriate to use these specimens for the fracture toughness test. In the case of the thin or side-grooved CCT specimen, the J value which is evaluated from the load versus displacement curve by using Rice's formula cannot estimate the J-integral at the central part of the specimen. Therefore, a J-integral estimation method would have to be established by using 3-D elasto-plastic analysis. (author)

  8. Osteochondritis Dissecans Involving the Trochlear Groove Treated With Retrograde Drilling: A Case Report.

    Science.gov (United States)

    Kaji, Yoshio; Nakamura, Osamu; Yamaguchi, Konosuke; Yamamoto, Tetsuji

    2015-09-01

    Osteochondritis dissecans (OCD) occurs frequently in the humeral capitellum of the upper extremity, whereas OCD involving the trochlear groove (trochlear groove OCD) is rarely reported. A standard treatment for trochlear groove OCD has therefore not been determined, although several methods have been tried.The case of a 14-year-old male gymnast with bilateral trochlear groove OCD is presented. Retrograde drilling from the lateral condyle of the humerus was applied for the OCD lesion of the left elbow, since it was larger in size than that in the right elbow and was symptomatic. Conversely, since the right lesion was small and asymptomatic, it was managed conservatively.After treatment, consolidation of the OCD lesions was observed in both elbows. However, the time to healing was shorter in the left elbow treated surgically than in the right elbow managed conservatively.In conclusion, retrograde drilling is a very simple and minimally invasive treatment. This case suggests that retrograde drilling for trochlear groove OCD may be a useful procedure that may accelerate the healing process for OCD lesions.

  9. Multiphysics Modeling of a Single Channel in a Nuclear Thermal Propulsion Grooved Ring Fuel Element

    Science.gov (United States)

    Kim, Tony; Emrich, William J., Jr.; Barkett, Laura A.; Mathias, Adam D.; Cassibry, Jason T.

    2013-01-01

    In the past, fuel rods have been used in nuclear propulsion applications. A new fuel element concept that reduces weight and increases efficiency uses a stack of grooved discs. Each fuel element is a flat disc with a hole on the interior and grooves across the top. Many grooved ring fuel elements for use in nuclear thermal propulsion systems have been modeled, and a single flow channel for each design has been analyzed. For increased efficiency, a fuel element with a higher surface-area-to-volume ratio is ideal. When grooves are shallower, i.e., they have a lower surface area, the results show that the exit temperature is higher. By coupling the physics of turbulence with those of heat transfer, the effects on the cooler gas flowing through the grooves of the thermally excited solid can be predicted. Parametric studies were done to show how a pressure drop across the axial length of the channels will affect the exit temperatures of the gas. Geometric optimization was done to show the behaviors that result from the manipulation of various parameters. Temperature profiles of the solid and gas showed that more structural optimization is needed to produce the desired results. Keywords: Nuclear Thermal Propulsion, Fuel Element, Heat Transfer, Computational Fluid Dynamics, Coupled Physics Computations, Finite Element Analysis

  10. Thrust Stand for Vertically Oriented Electric Propulsion Performance Evaluation

    Science.gov (United States)

    Moeller, Trevor; Polzin, Kurt A.

    2010-01-01

    A variation of a hanging pendulum thrust stand capable of measuring the performance of an electric thruster operating in the vertical orientation is presented. The vertical orientation of the thruster dictates that the thruster must be horizontally offset from the pendulum pivot arm, necessitating the use of a counterweight system to provide a neutrally-stable system. Motion of the pendulum arm is transferred through a balance mechanism to a secondary arm on which deflection is measured. A non-contact light-based transducer is used to measure displacement of the secondary beam. The members experience very little friction, rotating on twisting torsional pivots with oscillatory motion attenuated by a passive, eddy current damper. Displacement is calibrated using an in situ thrust calibration system. Thermal management and self-leveling systems are incorporated to mitigate thermal and mechanical drifts. Gravitational restoring force and torsional spring constants associated with flexure pivots provide restoring moments. An analysis of the design indicates that the thrust measurement range spans roughly four decades, with the stand capable of measuring thrust up to 12 N for a 200 kg thruster and up to approximately 800 mN for a 10 kg thruster. Data obtained from calibration tests performed using a 26.8 lbm simulated thruster indicated a resolution of 1 mN on 100 mN-level thrusts, while those tests conducted on 200 lbm thruster yielded a resolution of roughly 2.5 micro at thrust levels of 0.5 N and greater.

  11. Software trends for both the GANIL and spiral control

    International Nuclear Information System (INIS)

    David, L.; Lecorche, E.

    1999-01-01

    The Ganil facility has been running with a new control system since 1993. Many improvements have been done since that time to bring new capabilities to the system. So, in February 1996, when the Spiral control system was designed, it was mainly considered as an extension of the Ganil control system. This paper briefly recalls the basic architecture of the whole control system and the main choices upon which it relies. Then it presents the new software trends, to show how the Spiral control system has been integrated alongside the existing one. The last part describe the new developments and the most significant functionalities it brings as seen from the operator point of view, with some emphasis about the application programs for beam tuning. Indeed, these new programs have to be provided both for the spiral tuning with exotic ions beams and for the coupling of the Spiral and older Ganil facilities. (authors)

  12. Effects of abnormal excitation on the dynamics of spiral waves

    Science.gov (United States)

    Min-Yi, Deng; Xue-Liang, Zhang; Jing-Yu, Dai

    2016-01-01

    The effect of physiological and pathological abnormal excitation of a myocyte on the spiral waves is investigated based on the cellular automaton model. When the excitability of the medium is high enough, the physiological abnormal excitation causes the spiral wave to meander irregularly and slowly. When the excitability of the medium is low enough, the physiological abnormal excitation leads to a new stable spiral wave. On the other hand, the pathological abnormal excitation destroys the spiral wave and results in the spatiotemporal chaos, which agrees with the clinical conclusion that the early after depolarization is the pro-arrhythmic mechanism of some anti-arrhythmic drugs. The mechanisms underlying these phenomena are analyzed. Project supported by the National Natural Science Foundation of China (Grant Nos. 11365003 and 11165004).

  13. Effects of semiclassical spiral fluctuations on hole dynamics

    Science.gov (United States)

    Hamad, I. J.; Manuel, L. O.; Trumper, A. E.

    2012-01-01

    We investigate the dynamics of a single hole coupled to the spiral fluctuations related to the magnetic ground states of the antiferromagnetic J1-J2-J3 Heisenberg model on a square lattice. Using exact diagonalization on finite size clusters and the self-consistent Born approximation in the thermodynamic limit, we find, as a general feature, a strong reduction of the quasiparticle weight along the spiral phases of the magnetic phase diagram. For an important region of the Brillouin zone the hole spectral functions are completely incoherent, whereas at low energies the spectral weight is redistributed on several irregular peaks. We find a characteristic value of the spiral pitch Q=(0.7,0.7)π, for which the available phase space for hole scattering is maximum. We argue that this behavior is due to the nontrivial interference of the magnon-assisted and the free-hopping mechanism for hole motion, characteristic of a hole coupled to semiclassical spiral fluctuations.

  14. Measurement and structure of spiral wave response functions

    Science.gov (United States)

    Dierckx, Hans; Verschelde, Henri; Panfilov, Alexander V.

    2017-09-01

    The rotating spiral waves that emerge in diverse natural and man-made systems typically exhibit a particle-like behaviour since their adjoint critical eigenmodes (response functions) are often seen to be localised around the spiral core. We present a simple method to numerically compute response functions for circular-core and meandering spirals by recording their drift response to many elementary perturbations. Although our method is computationally more expensive than solving the adjoint system, our technique is fully parallellisable, does not suffer from memory limitations and can be applied to experiments. For a cardiac tissue model with the linear spiral core, we find that the response functions are localised near the turning points of the trajectory.

  15. Data Fusion Tool for Spiral Bevel Gear Condition Indicator Data

    Science.gov (United States)

    Dempsey, Paula J.; Antolick, Lance J.; Branning, Jeremy S.; Thomas, Josiah

    2014-01-01

    Tests were performed on two spiral bevel gear sets in the NASA Glenn Spiral Bevel Gear Fatigue Test Rig to simulate the fielded failures of spiral bevel gears installed in a helicopter. Gear sets were tested until damage initiated and progressed on two or more gear or pinion teeth. During testing, gear health monitoring data was collected with two different health monitoring systems. Operational parameters were measured with a third data acquisition system. Tooth damage progression was documented with photographs taken at inspection intervals throughout the test. A software tool was developed for fusing the operational data and the vibration based gear condition indicator (CI) data collected from the two health monitoring systems. Results of this study illustrate the benefits of combining the data from all three systems to indicate progression of damage for spiral bevel gears. The tool also enabled evaluation of the effectiveness of each CI with respect to operational conditions and fault mode.

  16. Relative frequencies of supernovae versus properties of spiral hosts

    OpenAIRE

    Hakobyan, A. A.; Nazaryan, T. A.; Adibekyan, V. Zh.; Petrosian, A. R.; Aramyan, L. S.; Kunth, D.; Mamon, G. A.; de Lapparent, V.; Bertin, E.; Gomes, J. M.; Turatto, M.

    2013-01-01

    In this work, we present an analysis of SNe number ratios in spiral galaxies with different morphological subtypes, luminosities, sSFR, and metallicities, to provide important information about the physical properties of the progenitor populations.

  17. Simulating Fatigue Crack Growth in Spiral Bevel Pinion

    National Research Council Canada - National Science Library

    Ural, Ani

    2003-01-01

    .... To obtain a more detailed understanding of the contact between a cracked pinion tooth in mesh with an uncracked gear tooth, three-dimensional contact analyses were performed on a spiral bevel gear...

  18. Cassini discovers a kinematic spiral ring around Saturn.

    Science.gov (United States)

    Charnoz, S; Porco, C C; Déau, E; Brahic, A; Spitale, J N; Bacques, G; Baillie, K

    2005-11-25

    Since the time of the Voyager flybys of Saturn in 1980-1981, Saturn's eccentric F ring has been known to be accompanied on either side by faint strands of material. New Cassini observations show that these strands, initially interpreted as concentric ring segments, are in fact connected and form a single one-arm trailing spiral winding at least three times around Saturn. The spiral rotates around Saturn with the orbital motion of its constituent particles. This structure is likely the result of differential orbital motion stretching an initial cloud of particles scattered from the dense core of the F ring. Different scenarios of formation, implying ringlet-satellite interactions, are explored. A recently discovered moon candidate, S/2004 S6, is on an orbit that crosses the F-ring core at the intersection of the spiral with the ring, which suggests a dynamical connection between S/2004 S6 and the spiral.

  19. Evolution of the Puente Hills Thrust Fault

    Science.gov (United States)

    Bergen, K. J.; Shaw, J. H.; Dolan, J. F.

    2013-12-01

    This study aims to assess the evolution of the blind Puente Hills thrust fault system (PHT) by determining its age of initiation, lateral propagation history, and changes in slip rate over time. The PHT presents one of the largest seismic hazards in the United States, given its location beneath downtown Los Angeles. The PHT is comprised of three fault segments: the Los Angeles (LA), Santa Fe Springs (SFS), and Coyote Hills (CH). The LA and SFS segments are characterized by growth stratigraphy where folds formed by uplift on the fault segments have been continually buried by sediment from the Los Angeles and San Gabriel rivers. The CH segment has developed topography and is characterized by onlapping growth stratigraphy. This depositional setting gives us the unique opportunity to measure uplift on the LA and SFS fault segments, and minimum uplift on the CH fault segment, as the difference in sediment thicknesses across the buried folds. We utilize depth converted oil industry seismic reflection data to image the fold geometries. Identifying time-correlative stratigraphic markers for slip rate determination in the basin has been a problem for researchers in the past, however, as the faunal assemblages observed in wells are time-transgressive by nature. To overcome this, we utilize the sequence stratigraphic model and well picks of Ponti et al. (2007) as a basis for mapping time-correlative sequence boundaries throughout our industry seismic reflection data from the present to the Pleistocene. From the Pleistocene to Miocene we identify additional sequence boundaries in our seismic reflection data from imaged sequence geometries and by correlating industry well formation tops. The sequence and formation top picks are then used to build 3-dimensional surfaces in the modeling program Gocad. From these surfaces we measure the change in thicknesses across the folds to obtain uplift rates between each sequence boundary. Our results show three distinct phases of

  20. Electromechanical actuation for thrust vector control applications

    Science.gov (United States)

    Roth, Mary Ellen

    1990-01-01

    At present, actuation systems for the Thrust Vector Control (TVC) for launch vehicles are hydraulic systems. The Advanced Launch System (ALS), a joint initiative between NASA and the Air Force, is a launch vehicle that is designed to be cost effective, highly reliable and operationally efficient with a goal of reducing the cost per pound to orbit. As part of this initiative, an electromechanical actuation system is being developed as an attractive alternative to the hydraulic systems used today. NASA-Lewis is developing and demonstrating an Induction Motor Controller Actuation System with a 40 hp peak rating. The controller will integrate 20 kHz resonant link Power Management and Distribution (PMAD) technology and Pulse Population Modulation (PPM) techniques to implement Field Oriented Vector Control (FOVC) of a new advanced induction motor. Through PPM, multiphase variable frequency, variable voltage waveforms can be synthesized from the 20 kHz source. FOVC shows that varying both the voltage and frequency and their ratio (V/F), permits independent control of both torque and speed while operating at maximum efficiency at any point on the torque-speed curve. The driver and the FOVC will be microprocessor controlled. For increased system reliability, a Built-in Test (BITE) capability will be included. This involves introducing testability into the design of a system such that testing is calibrated and exercised during the design, manufacturing, maintenance and prelaunch activities. An actuator will be integrated with the motor controller for performance testing of the EMA TVC system. The design and fabrication of the motor controller is being done by General Dynamics Space Systems Division. The University of Wisconsin-Madison will assist in the design of the advanced induction motor and in the implementation of the FOVC theory. A 75 hp electronically controlled dynamometer will be used to test the motor controller in all four quadrants of operation using flight type

  1. Dosimetry in dental radiology. Dentascan spiral CT versus panoramic radiography

    International Nuclear Information System (INIS)

    Villari, N.; Stecco, A.; Zatelli, G.

    1999-01-01

    The study compares the doses absorbed by the dentomaxillary area in spiral CT and panoramic examinations. The dose measurements demonstrate that patients receive smaller doses with panoramic radiography than with spiral CT with Dentascan. After following for some variations from instrumental differences, they are in substantial agreement with literature data. Further investigations are needed considering the radiobiological risk related to the growing spread of Dentascan examinations [it

  2. Scintigraphic diagnosis of spiral fracture in young children

    International Nuclear Information System (INIS)

    Hossein-Foucher, C.; Venel, H.; Lecouffe, P.; Ythier, H.; Legghe, R.; Marchandise, X.

    1988-01-01

    8 cases of unsuspected bone fracture in children, identified at bone scan are reported. Common features were the children's young age (1 to 3 years), the absence of clinical suspicion, the initially normal X-rays, the fracture type (spiral fracture of the tibia undisplaced), and the uniform appearance of the bone scan. These data confim the value of bone scan in limping children and suggest that spiral fracture of the tibia is a frequent and underdiagnosed condition in children [fr

  3. Lung studies with spiral CT. pitch 1 versus pitch 2

    International Nuclear Information System (INIS)

    Sartoni Galloni, S.; Miceli, M.; Lipparino, M.; Burzi, M.; Gigli, F.; Rossi, M.S.; Santoli, G.; Guidarelli, G.

    1999-01-01

    In Spiral CT, the pitch is the ratio of the distance to tabletop travels per 360 degrees rotation to nominal slice width, expressed in mm. Performing Spiral CT examination with pitch 2 allows to reduce examination time, exposure and contrast dose, and X-ray tube overload. The authors investigated the yield of pitch 2 in lung parenchyma studies, particular relative to diagnostic image quality [it

  4. The accelerated ISOL technique and the SPIRAL project

    International Nuclear Information System (INIS)

    Villari, A.C.C.

    2001-01-01

    The accelerated ISOL technique is presented as an introduction to the present status of the SPIRAL facility. SPIRAL is based on the very high intensity light and heavy ion beams available at GANIL. The facility will deliver radioactive beams with energies in the range between 1.7 A and 25 A MeV. The presently target-ion source production system, as well the new developments undertaken by the target ion-source group at GANIL are presented. (authors)

  5. An Experimental Study of Flow Separation over a Flat Plate with Transverse Grooves

    Science.gov (United States)

    Jones, Emily; Lang, Amy

    2012-11-01

    A shark's scales help to reduce drag over its body by controlling boundary layer separation over its skin. It is theorized that the scales bristle when encountering a reversing flow, thereby trapping vortices between the scales, creating a partial slip condition over the surface and inducing turbulence augmentation in the boundary layer. In an attempt to replicate and study these effects, a spinning cylinder was used in a water tunnel to induce separation over a flat plate with 2 mm, square 2-D transverse grooves and sinusoidal grooves of the same size. The results were compared to tripped, turbulent boundary layer separation occurring over a flat plate without grooves using DPIV. The strength of the adverse pressure gradient was varied, and the observed delay in flow separation and other effects upon the boundary layer are discussed. Funding received by NSF REU grant 1062611.

  6. Ancient schwannoma at the olfactory groove mimicking meningioma: A case report

    Energy Technology Data Exchange (ETDEWEB)

    Heo, Young Jin; Jeong, Hae Woong [Dept. of Radiology, Busan Paik Hospital, Inje University College of Medicine, Busan (Korea, Republic of)

    2015-12-15

    Schwannomas are benign slow-growing nerve sheath tumors, which can develop in any peripheral or central nerve that contains Schwann cells. Schwannomas located near the olfactory groove are extremely rare and radiological diagnosis can be difficult. Moreover, ancient schwannoma is an uncommon variant, and radiologic findings are rarely reported. Herein, we reported a surgically confirmed case of ancient schwannoma at the olfactory groove in a 44-year-old woman presenting with headache and visual disturbance. Brain magnetic resonance imaging (MRI) showed a solid and cystic extra-axial mass located in the subfrontal area mimicking an olfactory groove meningioma. Histopathologic diagnosis of ancient schwannoma was confirmed by immunohistochemical staining for S100, CD56, vimentin, and other markers. Furthermore, we described the clinical manifestations, MRI characteristics, and histopathologic findings of the case, and presented a review of related literature.

  7. Levitation and locomotion on an air-table of plates with herringbone grooves

    Science.gov (United States)

    Hinch, John; de Maleprade, Helene

    2017-11-01

    Recent experiments in ESPCI in Paris and numerical simulations in Nano- and Microfluidics in Darmstadt have shown that plates with herringbone grooves in their base are accelerated on an air-table in the direction that the chevron grooves point. A simple two-dimensional model is constructed of the air flow down a channel with pressure controlled influx across the lower boundary. Limiting cases are considered of low and high Reynolds numbers, and of small and large pressure drop down the channel compared with the pressure drop across the porous plate. The levitation and locomotion forces are calculated. A prediction is made for the locomotive acceleration which avoids the complications of the shorter grooves which exit the front and back edges.

  8. Modelling of transport phenomena in 3D GMAW of thick metals with V groove

    Energy Technology Data Exchange (ETDEWEB)

    Hu, J [Department of Mechanical Engineering, University of Bridgeport, Bridgeport, CT 06604 (United States); Tsai, H L [Department of Mechanical and Aerospace Engineering, Missouri University of Science and Technology, 1870 Miner Circle, Rolla, MO 65409 (United States)

    2008-03-21

    This paper analyses the dynamic process of groove filling and the resulting weld pool fluid flow in gas metal arc welding of thick metals with V groove. Filler droplets carrying mass, momentum, thermal energy and sulfur species are periodically impinged onto the workpiece. The complex transport phenomena in the weld pool, caused by the combined effect of droplet impingement, gravity, electromagnetic force, surface tension and plasma arc pressure, were investigated to determine the transient weld pool shape and distributions of velocity, temperature and sulfur species in the weld pool. It was found that the groove provides a channel which can smooth the flow in the weld pool, leading to poor mixing between the filler metal and the base metal.

  9. Finite Element Modeling of Strain Distribution through Sheet Thickness during Cold Rolling with Grooved Rolls

    Directory of Open Access Journals (Sweden)

    Pesin A.

    2015-01-01

    Full Text Available Plastic strain control of aluminum alloys are of importance for improvement of sheet microstructure and properties. The paper presents a numerical analysis of the strain distribution through pure Al sheet thickness during cold rolling with flat and grooved rolls. FEM simulations were carried out with using software DEFORM 3D. For verification of the numeric modeling results, the experimental analysis was carried out. The influence of the roll shape on strain distribution through Al sheet thickness was studied. It was shown that the strain effective increases from 0.9 to 1.5 during cold rolling with grooved rolls, when depth of indentation of grooved rolls in sheet increases from 0.25 to 0.50 mm. FE model can be used to optimize the cold rolling process to improve microstructure and mechanical properties of aluminum sheets.

  10. Palatogingival Groove: Recognizing and Managing the Hidden Tract in a Maxillary Incisor: A Case Report

    Science.gov (United States)

    Sharma, Sarang; Deepak, Passi; Vivek, Sharma; Ranjan Dutta, Shubha

    2015-01-01

    Palatogingival grooves are developmental malformations quite notorious for precipitating endodontic - periodontal lesions. Owing to their inconspicuous occurrence, funnel-shaped morphology and variable extent on tooth root, they promote adherence of plaque and bacteria to levels significant for the development of pathology. Several treatment approaches have been recognized in literature for the management of this anomaly. Here in this report, a 25-year-old patient reported with the complaint of pain and swelling in maxillary right lateral incisor. Clinical examination confirmed an endodontic - periodontal lesion in relation to palatogingival groove. Endodontic treatment was instituted, followed by odontoplasty of the groove and restoration with newer calcium silicate cement, Biodentine. Combined endodontic - periodontal approach was successful in resolving the pathology with complete healing seen both clinically and radiographically. Timely diagnosis, prevention and management are highly recommended to prevent tooth loss due to complications arising secondary to their presence. PMID:26124612

  11. The restoration of thrust systems and displacement continuity around the Mont Blanc massif, NW external Alpine thrust belt

    Science.gov (United States)

    Butler, Robert W. H.

    Foreland-propagating external thrust belts may be considered as essentially plane strain phenomena so that displacements can be correlated throughout their linked, three-dimensional fault geometry. This approach has been applied to part of the northwest external French-Swiss Alps, around the Mont Blanc basement massif. Imbricates of basement and cover sequences on the SW margin of this massif restore to a width in excess of 77 km with an implicit shortening of at least 67 km. These displacements can be correlated with those in the neighbouring Helvetic nappes by transferring movements, via lateral branch lines, onto the Mont Blanc thrust. By reappraising thrust geometries, the Helvetic/Ultrahelvetic nappe complex has been restored to a width of 114 km to the ESE of the Aiguilles Rouges basement massif. Displacements on the internal (SE) margin of the Mont Blanc massif, estimated by balanced sections and a restoration of the Ultrahelvetic klippen in the sub-alps, exceed 59 km. Thrust continuity, incorporating the restorations of nappes and imbricate geometries around the Mont Blanc massif, is illustrated on a crude, restored branch-line map which also serves as a preliminary palaeogeographic reconstruction. External thrust systems, to the east of the external Belledonne/Aiguilles Rouges massif, restore to a width of at least 140 km in the footwall to the Frontal Pennine thrust.

  12. Spiralizations and tropisms in Arabidopsis roots.

    Science.gov (United States)

    Migliaccio, F; Piconese, S

    2001-12-01

    When Arabidopsis seedlings are grown on a hard-agar plate, their primary roots show characteristic spiralling movements, apparent as waves, coils and torsions, together with a slanting toward the right-hand side. All these movements are believed to be the result of three different processes acting on the roots: circumnutation, positive gravitropism and negative thigmotropism. The basic movement of the roots is described as that of a growing right-handed helix, which, because of the root tip hitting the agar plate, is continuously switched from the right-hand to the left-hand of the growth direction, and vice versa. This movement also produces a slanting root-growth direction toward the right-hand because of the incomplete waves made by the right-handed root to the left-hand. By contrast, the torsions seen in the coils and waves are interpreted as artefacts that form as an adaptation of the three-dimensional root helix to the flat two-dimensional agar surface.

  13. Noncontrast peripheral MRA with spiral echo train imaging.

    Science.gov (United States)

    Fielden, Samuel W; Mugler, John P; Hagspiel, Klaus D; Norton, Patrick T; Kramer, Christopher M; Meyer, Craig H

    2015-03-01

    To develop a spin echo train sequence with spiral readout gradients with improved artery-vein contrast for noncontrast angiography. Venous T2 becomes shorter as the echo spacing is increased in echo train sequences, improving contrast. Spiral acquisitions, due to their data collection efficiency, facilitate long echo spacings without increasing scan times. Bloch equation simulations were performed to determine optimal sequence parameters, and the sequence was applied in five volunteers. In two volunteers, the sequence was performed with a range of echo times and echo spacings to compare with the theoretical contrast behavior. A Cartesian version of the sequence was used to compare contrast appearance with the spiral sequence. Additionally, spiral parallel imaging was optionally used to improve image resolution. In vivo, artery-vein contrast properties followed the general shape predicted by simulations, and good results were obtained in all stations. Compared with a Cartesian implementation, the spiral sequence had superior artery-vein contrast, better spatial resolution (1.2 mm(2) versus 1.5 mm(2) ), and was acquired in less time (1.4 min versus 7.5 min). The spiral spin echo train sequence can be used for flow-independent angiography to generate three-dimensional angiograms of the periphery quickly and without the use of contrast agents. © 2014 Wiley Periodicals, Inc.

  14. Mechanics and spiral formation in the rat cornea.

    Science.gov (United States)

    Mohammad Nejad, T; Iannaccone, S; Rutherford, W; Iannaccone, P M; Foster, C D

    2015-01-01

    During the maturation of some mammals such as mice and rats, corneal epithelial cells tend to develop into patterns such as spirals over time. A better understanding of these patterns can help to understand how the organ develops and may give insight into some of the diseases affecting corneal development. In this paper, a framework for explaining the development of the epithelial cells forming spiral patterns due to the effect of tensile and shear strains is proposed. Using chimeric animals, made by combining embryonic cells from genetically distinguishable strains, we can observe the development of patterns in the cornea. Aggregates of cell progeny from one strain or the other called patches form as organs and tissue develop. The boundaries of these patches are fitted with logarithmic spirals on confocal images of adult rat corneas. To compare with observed patterns, we develop a three-dimensional large strain finite element model for the rat cornea under intraocular pressure to examine the strain distribution on the cornea surface. The model includes the effects of oriented and dispersed fibrils families throughout the cornea and a nearly incompressible matrix. Tracing the directions of critical strain vectors on the cornea surface leads to spiral-like curves that are compared to the observed logarithmic spirals. Good agreement between the observed and numerical curves supports the proposed assumption that shear and tensile strains facilitate sliding of epithelial cells to develop spiral patterns.

  15. Improved MRI thermometry with multiple-echo spirals.

    Science.gov (United States)

    Marx, Michael; Butts Pauly, Kim

    2016-09-01

    Low-bandwidth PRF shift thermometry is used to guide HIFU ablation treatments. Low sampling bandwidth is needed for high signal-to-noise ratio with short acquisition times, but can lead to off-resonance artifacts. In this work, improved multiple-echo thermometry is presented that allows for high bandwidth and reduced artifacts. It is also demonstrated with spiral sampling, to improve the trade-off between resolution, speed, and measurement precision. Four multiple-echo thermometry sequences were tested in vivo, one using two-dimensional Fourier transform (2DFT) sampling and three using spirals. The spiral sequences were individually optimized for resolution, for speed, and for precision. Multifrequency reconstruction was used to correct for off-resonance spiral artifacts. Additionally, two different multiecho temperature reconstructions were compared. Weighted combination of per-echo phase differences gave significantly better precision than least squares off-resonance estimation. Multiple-echo 2DFT sequence obtained precision similar to single-echo 2DFT, while greatly increasing sampling bandwidth. The multiecho spiral acquisitions achieved 2× better resolution, 2.9× better uncertainty, or 3.4× faster acquisition time, without negatively impacting the other two design parameters as compared to single-echo 2DFT. Multiecho spiral thermometry greatly improves the capabilities of temperature monitoring, and could improve transcranial treatment monitoring capabilities. Magn Reson Med 76:747-756, 2016. © 2015 Wiley Periodicals, Inc. © 2015 Wiley Periodicals, Inc.

  16. Spiral instabilities in media supporting complex oscillations under periodic forcing

    Science.gov (United States)

    Gao, Qingyu; Li, Jun; Zhang, Kailong; Epstein, Irving R.

    2009-09-01

    The periodically forced Brusselator model displays temporal mixed-mode and quasiperiodic oscillations, period doubling, and chaos. We explore the behavior of such media as reaction-diffusion systems for investigating spiral instabilities. Besides near-core breakup and far-field breakup resulting from unstable modes in the radial direction or Doppler-induced instability (destabilization of the core's location), the observed complex phenomena include backfiring, spiral regeneration, and amplitude modulation from line defects. Amplitude modulation of spirals can evolve to chambered spirals resembling those found in nature, such as pine cones and sunflowers. When the forcing amplitude is increased, the spiral-tip meander evolves from simple rotation to complex petals, corresponding to transformation of the local dynamics from simple oscillations to mixed-mode, period-2, and quasiperiodic oscillations. The number of petals is related to the complexity of the mixed-mode oscillations. Spiral turbulence, standing waves, and homogeneous synchronization permeate the entire system when the forcing amplitude is further increased.

  17. Comparative evaluation of three heat transfer enhancement strategies in a grooved channel

    Energy Technology Data Exchange (ETDEWEB)

    Herman, C.; Kang, E. [Dept. of Mechanical Engineering, Johns Hopkins Univ., Baltimore, MD (United States)

    2001-09-01

    Results of a comparative evaluation of three heat transfer enhancement strategies for forced convection cooling of a parallel plate channel populated with heated blocks, representing electronic components mounted on printed circuit boards, are reported. Heat transfer in the reference geometry, the asymmetrically heated parallel plate channel, is compared with that for the basic grooved channel, and the same geometry enhanced by cylinders and vanes placed above the downstream edge of each heated block. In addition to conventional heat transfer and pressure drop measurements, holographic interferometry combined with high-speed cinematography was used to visualize the unsteady temperature fields in the self-sustained oscillatory flow. The locations of increased heat transfer within one channel periodicity depend on the enhancement technique applied, and were identified by analyzing the unsteady temperature distributions visualized by holographic interferometry. This approach allowed gaining insight into the mechanisms responsible for heat transfer enhancement. Experiments were conducted at moderate flow velocities in the laminar, transitional and turbulent flow regimes. Reynolds numbers were varied in the range Re = 200-6500, corresponding to flow velocities from 0.076 to 2.36 m/s. Flow oscillations were first observed between Re = 1050 and 1320 for the basic grooved channel, and around Re = 350 and 450 for the grooved channels equipped with cylinders and vanes, respectively. At Reynolds numbers above the onset of oscillations and in the transitional flow regime, heat transfer rates in the investigated grooved channels exceeded the performance of the reference geometry, the asymmetrically heated parallel plate channel. Heat transfer in the grooved channels enhanced with cylinders and vanes showed an increase by a factor of 1.2-1.8 and 1.5-3.5, respectively, when compared to data obtained for the basic grooved channel; however, the accompanying pressure drop penalties

  18. High-Tc Superconducting Thick-Film Spiral Magnet: Development and Characterization of a Single Spiral Module

    National Research Council Canada - National Science Library

    McGinnis, W

    1997-01-01

    The objective of this project was to make characterized and numerically model prototype modules of a new type of superconducting electromagnet based on stacked spirals of superconducting thick films...

  19. Liquid phase solvent bonding of plastic microfluidic devices assisted by retention grooves.

    Science.gov (United States)

    Wan, Alwin M D; Sadri, Amir; Young, Edmond W K

    2015-01-01

    We report a novel method for achieving consistent liquid phase solvent bonding of plastic microfluidic devices via the use of retention grooves at the bonding interface. The grooves are patterned during the regular microfabrication process, and can be placed at the periphery of a device, or surrounding microfluidic features with open ports, where they effectively mitigate solvent evaporation, and thus substantially reduce poor bond coverage. This method is broadly applicable to a variety of plastics and solvents, and produces devices with high bond quality (i.e., coverage, strength, and microfeature fidelity) that are suitable for studies in physics, chemistry, and cell biology at the microscale.

  20. Efficient Excitation of Channel Plasmons in Tailored, UV-Lithography-Defined V-Grooves

    DEFF Research Database (Denmark)

    Smith, Cameron L. C.; Thilsted, Anil Haraksingh; Garcia-Ortiz, Cesar E.

    2014-01-01

    We demonstrate the highly efficient (>50%) conversion of freely propagating light to channel plasmon-polaritons (CPPs) in gold V-groove waveguides using compact 1.6 μm long waveguide-termination coupling mirrors. Our straightforward fabrication process, involving UV-lithography and crystallographic...... silicon etching, forms the coupling mirrors innately and ensures exceptional-quality, wafer-scale device production. We tailor the V-shaped profiles by thermal silicon oxidation in order to shift initially wedge-located modes downward into the V-grooves, resulting in well-confined CPPs suitable...

  1. Bifurcation analysis of an aerodynamic journal bearing system considering the effect of stationary herringbone grooves

    Energy Technology Data Exchange (ETDEWEB)

    Wang, C.-C. [Department of Mechanical Engineering, Far East College, 49, Hsin-Shih, Tainan 744, Taiwan (China)]. E-mail: ccwang@cc.fec.edu.tw

    2007-08-15

    This paper investigates the bifurcation and nonlinear behavior of an aerodynamic journal bearing system taking into account the effect of stationary herringbone grooves. A finite difference method based on the successive over relation approach is employed to solve the Reynolds' equation. The analysis reveals a complex dynamical behavior comprising periodic and quasi-periodic responses of the rotor center. The dynamic behavior of the bearing system varies with changes in the bearing number and rotor mass. The results of this study provide a better understanding of the nonlinear dynamics of aerodynamic grooved journal bearing systems.

  2. Influence of Journal Bearing Axial Grooves on the Dynamic Behavior of Horizontal Rotors

    Directory of Open Access Journals (Sweden)

    Miguel Angelo de Carvalho Michalski

    2006-01-01

    Full Text Available Journal bearing design and the lubricant characteristics are very influential in a rotating machine behaviour. The bearing geometry can drastically affect the lubricant flow and also the rotor dynamics. Approaching that issue, this paper presents an experimental study of the dynamic behavior of a horizontal rotor suported by journal bearings with semi-circular axial grooves. The journal bearings were manufactured with a varied number of axial grooves and a versatile test rig is used, making possible the analysis of different configurations. The acquired signals are analyzed with classical and non-linear tools and the differences among the rotors’ configurations can be shown.

  3. Disk in a groove with friction: An analysis of static equilibrium and indeterminacy

    Science.gov (United States)

    Donolato, Cesare

    2018-05-01

    This note studies the statics of a rigid disk placed in a V-shaped groove with frictional walls and subjected to gravity and a torque. The two-dimensional equilibrium problem is formulated in terms of the angles that contact forces form with the normal to the walls. This approach leads to a single trigonometric equation in two variables whose domain is determined by Coulomb's law of friction. The properties of solutions (existence, uniqueness, or indeterminacy) as functions of groove angle, friction coefficient and applied torque are derived by a simple geometric representation. The results modify some of the conclusions by other authors on the same problem.

  4. An explanation of a groove found on the nasal process of the equine incisive bone.

    Science.gov (United States)

    Pérez, W; Martin, E

    2001-12-01

    Thirteen fresh equine heads were dissected in an attempt to determine the cause of a groove frequently found on the dorsal border and medial side of the nasal process of the incisive bone. This groove appeared on both sides in 40 out of 44 equine skulls. The sulcus seems to be caused by the combined action of the lateralis nasi muscle and the medial accessory cartilage of the nose (cartilago nasalis accessoria medialis). Other sulci found on the nasal process of the bone may be explained as impressions caused by nerves.

  5. Bifurcation analysis of an aerodynamic journal bearing system considering the effect of stationary herringbone grooves

    International Nuclear Information System (INIS)

    Wang, C.-C.

    2007-01-01

    This paper investigates the bifurcation and nonlinear behavior of an aerodynamic journal bearing system taking into account the effect of stationary herringbone grooves. A finite difference method based on the successive over relation approach is employed to solve the Reynolds' equation. The analysis reveals a complex dynamical behavior comprising periodic and quasi-periodic responses of the rotor center. The dynamic behavior of the bearing system varies with changes in the bearing number and rotor mass. The results of this study provide a better understanding of the nonlinear dynamics of aerodynamic grooved journal bearing systems

  6. SPIRAL COUNTER-CURRENT CHROMATOGRAPHY OF SMALL MOLECULES, PEPTIDES AND PROTEINS USING THE SPIRAL TUBING SUPPORT ROTOR

    OpenAIRE

    Knight, Martha; Finn, Thomas M.; Zehmer, John; Clayton, Adam; Pilon, Aprile

    2011-01-01

    An important advance in countercurrent chromatography (CCC) carried out in open flow-tubing coils, rotated in planetary centrifuges, is the new design to spread out the tubing in spirals. More spacing between the tubing was found to significantly increase the stationary phase retention, such that now all types of two-phase solvent systems can be used for liquid-liquid partition chromatography in the J-type planetary centrifuges. A spiral tubing support (STS) frame with circular channels was c...

  7. Effect of pre-combustion characteristics in pulse detonation engine using shchelkin spiral

    Directory of Open Access Journals (Sweden)

    C. T. Dheeraj Kumar Singh

    2016-09-01

    Full Text Available Pulse detonation engines are the modern propulsive device which provides high thrust. They are unsteady propulsive devices which has multi cycle operations in it. In this multi cycle process for every cycle fuel and air are initiated and a shock wave is generated in combustion chamber in form of deflagration. Combustion chamber is maintained with high pressure and high temperature which leads to combustion of reactants. This deflagration transmits to detonation with high velocity and increasing Mach number. Deflagration propagates forward by taking all unburned species and products formed after combustion. Propagation of Deflagration – Detonation Transition (DDT shock wave studies is a pioneering research concept. In the present study, simulation of PDE with Shchelkin spiral geometry is considered with two mass flow inlets has been used in which one is for fuel inlet and other for oxidizer. Geometry and meshing has been done in Gambit. Fuel used is gaseous fuel hydrogen and oxidizer is air mixture of O2, N2 work has been performed for different mass flow rates of fuel and oxidizer. Energy equation, Species transport equation to be solved in Fluent. Comparison results of DDT in parameters of mach number, velocity, pressure and temperatures depending on different time steps have been observed

  8. Contractile structures at the southern end of the central Nevada thrust belt

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, W.J. (Univ. of Nevada, Las Vegas, NV (United States). Dept. of Geosciences)

    1993-04-01

    The Timpahute Range and Mt. Irish form an E-trending topographic high which is relatively unextended allowing a rare view of the contractile structures in the Mesozoic( ) Central Nevada thrust belt. Recent mapping indicates: (1) moderately to steeply W-dipping thrusts, the Mt. Irish and Lincoln thrusts; (2) long ramps; (3) structurally complicated footwalls; and 4. large open folds. The 30--50 W-dipping Mt. Irish thrust places Cambrian and Ordovician over Mississippian and Devonian units ([approximately]2,200 m of stratigraphic separation). The immediate footwall of the thrust consists of dominantly steeply-dipping horses. The hanging wall contains a large open anticline. Northward, this thrust correlates with the Golden Gate thrust (P.A. Armstong, 1990) which has similar footwall and hanging wall structures and compatible stratigraphic separation. The 30--50[degree]W-dipping Lincoln thrust crops out [approximately]15 km west of the Mt. Irish thrust. The Lincoln thrust places an open syncline containing Lower Ordovician and Cambrian over Mississippian and Devonian rocks in a duplex. The duplex contains both thrusts and tear faults. The nearest thrust along strike to the north is the Freiberg thrust (M.W. Martin, 1987). However, the Freiberg thrust places Middle Ordovician over Devonian rocks without an underlying duplex. New mapping demonstrates that additional duplex crops out along strike between the Lincoln and Freiberg thrusts. The duplex geometry accommodates changes in stratigraphic separation along a gently-dipping lateral ramp and permits correlation of the Freiberg and Lincoln thrusts. These data, interpretations and balanced cross section suggest that the southern Central Nevada thrust belt is composed of ramp-dominated thrusts. The open folds are either fault-bend or fault-growth folds. The duplex under the Lincoln thrust allows geometrical accommodation of along-strike variations in stratigraphic separation across the thrust.

  9. Coupled Dynamics of a Rotor-Journal Bearing System Equipped with Thrust Bearings

    OpenAIRE

    Yu Lie; R.B. Bhat

    1995-01-01

    The rotordynamic coefficients of fixed-pad thrust bearing are introduced and calculated by using the out-domain method, and a general analysis method is developed to investigate the coupled dynamics of a rotor equipped with journal and thrust bearings simultaneously. Considerations include the effects of static tilt parameters of the rotor on rotordynamic coefficients of thrust bearing and the action of thrust bearing on system dynamics. It is shown that thrust bearing changes the load distri...

  10. Lateral Vibration of Hydroelectric Generating Set with Different Supporting Condition of Thrust Pad

    OpenAIRE

    Si, Xiaohui; Lu, Wenxiu; Chu, Fulei

    2011-01-01

    The variations of the supporting condition, which change the stiffness of tilting pad thrust bearing, may alter the dynamic behavior of the rotor system. The effects of supporting condition of thrust pad on the lateral vibration of a hydroelectric generating set are investigated in this paper. The action of a thrust bearing is described as moments acting on the thrust collar, and the tilting stiffness coefficients of thrust bearing are calculated. A model based on typical beam finite element ...

  11. Engineering research, development and technology: Thrust area report FY 91

    International Nuclear Information System (INIS)

    1991-01-01

    The mission of the Engineering Research, Development, and Technology Program at Lawrence, Livermore National Laboratory (LLNL) is to develop the technical staff and the technology needed to support current and future LLNL programs. To accomplish this mission, the Engineering Research, Development, and Technology Program has two important goals: (1) to identify key technologies and (2) conduct high quality work to enhance our capabilities in these key technologies. To help focus our efforts, we identify technology thrust areas and select technical leaders for each area. The thrust areas are integrated engineering activities and, rather than being based on individual disciplines, they are staffed by personnel from Electronics Engineering, Mechanical Engineering, and other LLNL organizations, as appropriate. The thrust area leaders are expected to establish strong links to LLNL program leaders and to industry; to use outside and inside experts to review the quality and direction of the work; to use university contacts to supplement and complement their efforts; and to be certain that we are not duplicating the work of others. The thrust area leader is also responsible for carrying out the work that follows from the Engineering Research, Development, and Technology Program so that the results can be applied as early as possible to the needs of LLNL programs. This annual report, organized by thrust area, describes activities conducted within the Program for the fiscal year, 1991. Its intent is to provide timely summaries of objectives, theories, methods, and results

  12. Clear New View of a Classic Spiral

    Science.gov (United States)

    2010-05-01

    ESO is releasing a beautiful image of the nearby galaxy Messier 83 taken by the HAWK-I instrument on ESO's Very Large Telescope (VLT) at the Paranal Observatory in Chile. The picture shows the galaxy in infrared light and demonstrates the impressive power of the camera to create one of the sharpest and most detailed pictures of Messier 83 ever taken from the ground. The galaxy Messier 83 (eso0825) is located about 15 million light-years away in the constellation of Hydra (the Sea Serpent). It spans over 40 000 light-years, only 40 percent the size of the Milky Way, but in many ways is quite similar to our home galaxy, both in its spiral shape and the presence of a bar of stars across its centre. Messier 83 is famous among astronomers for its many supernovae: vast explosions that end the lives of some stars. Over the last century, six supernovae have been observed in Messier 83 - a record number that is matched by only one other galaxy. Even without supernovae, Messier 83 is one of the brightest nearby galaxies, visible using just binoculars. Messier 83 has been observed in the infrared part of the spectrum using HAWK-I [1], a powerful camera on ESO's Very Large Telescope (VLT). When viewed in infrared light most of the obscuring dust that hides much of Messier 83 becomes transparent. The brightly lit gas around hot young stars in the spiral arms is also less prominent in infrared pictures. As a result much more of the structure of the galaxy and the vast hordes of its constituent stars can be seen. This clear view is important for astronomers looking for clusters of young stars, especially those hidden in dusty regions of the galaxy. Studying such star clusters was one of the main scientific goals of these observations [2]. When compared to earlier images, the acute vision of HAWK-I reveals far more stars within the galaxy. The combination of the huge mirror of the VLT, the large field of view and great sensitivity of the camera, and the superb observing conditions

  13. CHARACTERIZING SPIRAL ARM AND INTERARM STAR FORMATION

    Energy Technology Data Exchange (ETDEWEB)

    Kreckel, K.; Schinnerer, E.; Meidt, S. [Max Planck Institut für Astronomie, Königstuhl 17, D-69117 Heidelberg (Germany); Blanc, G. A. [Departamento de Astronomía, Universidad de Chile, Camino del Observatorio 1515, Las Condes, Santiago (Chile); Groves, B. [Research School of Astronomy and Astrophysics, Australian National University, Canberra, ACT 2611 (Australia); Adamo, A. [Department of Astronomy, The Oskar Klein Centre, Stockholm University, AlbaNova University Centre, SE-106 91 Stockholm (Sweden); Hughes, A., E-mail: kreckel@mpia.de [CNRS, IRAP, 9 Av. du Colonel Roche, BP 44346, F-31028 Toulouse cedex 4 (France)

    2016-08-20

    Interarm star formation contributes significantly to a galaxy’s star formation budget and provides an opportunity to study stellar birthplaces unperturbed by spiral arm dynamics. Using optical integral field spectroscopy of the nearby galaxy NGC 628 with VLT/MUSE, we construct H α maps including detailed corrections for dust extinction and stellar absorption to identify 391 H ii regions at 35 pc resolution over 12 kpc{sup 2}. Using tracers sensitive to the underlying gravitational potential, we associate H ii regions with either arm (271) or interarm (120) environments. Using our full spectral coverage of each region, we find that most physical properties (luminosity, size, metallicity, ionization parameter) of H ii regions are independent of environment. We calculate the fraction of H α luminosity due to the background of diffuse ionized gas (DIG) contaminating each H ii region, and find the DIG surface brightness to be higher within H ii regions than in the surroundings, and slightly higher within arm H ii regions. Use of the temperature-sensitive [S ii]/H α line ratio instead of the H α surface brightness to identify the boundaries of H ii regions does not change this result. Using the dust attenuation as a tracer of the gas, we find depletion times consistent with previous work (2 × 10{sup 9} yr) with no differences between the arm and interarm, but this is very sensitive to the DIG correction. Unlike molecular clouds, which can be dynamically affected by the galactic environment, we see fairly consistent properties of H ii regions in both arm and interarm environments. This suggests either a difference in star formation and feedback in arms or a decoupling of dense star-forming clumps from the more extended surrounding molecular gas.

  14. DNA minor groove electrostatic potential: influence of sequence-specific transitions of the torsion angle gamma and deoxyribose conformations.

    Science.gov (United States)

    Zhitnikova, M Y; Shestopalova, A V

    2017-11-01

    The structural adjustments of the sugar-phosphate DNA backbone (switching of the γ angle (O5'-C5'-C4'-C3') from canonical to alternative conformations and/or C2'-endo → C3'-endo transition of deoxyribose) lead to the sequence-specific changes in accessible surface area of both polar and non-polar atoms of the grooves and the polar/hydrophobic profile of the latter ones. The distribution of the minor groove electrostatic potential is likely to be changing as a result of such conformational rearrangements in sugar-phosphate DNA backbone. Our analysis of the crystal structures of the short free DNA fragments and calculation of their electrostatic potentials allowed us to determine: (1) the number of classical and alternative γ angle conformations in the free B-DNA; (2) changes in the minor groove electrostatic potential, depending on the conformation of the sugar-phosphate DNA backbone; (3) the effect of the DNA sequence on the minor groove electrostatic potential. We have demonstrated that the structural adjustments of the DNA double helix (the conformations of the sugar-phosphate backbone and the minor groove dimensions) induce changes in the distribution of the minor groove electrostatic potential and are sequence-specific. Therefore, these features of the minor groove sizes and distribution of minor groove electrostatic potential can be used as a signal for recognition of the target DNA sequence by protein in the implementation of the indirect readout mechanism.

  15. Modeling and simulation of stamp deflections in nanoimprint lithography: Exploiting backside grooves to enhance residual layer thickness uniformity

    DEFF Research Database (Denmark)

    Taylor, Hayden; Smistrup, Kristian; Boning, Duane

    2011-01-01

    We describe a model for the compliance of a nanoimprint stamp etched with a grid of backside grooves. We integrate the model with a fast simulation technique that we have previously demonstrated, to show how etched grooves help reduce the systematic residual layer thickness (RLT) variations...

  16. Gradient rotating outer volume excitation (GROOVE): A novel method for single-shot two-dimensional outer volume suppression.

    Science.gov (United States)

    Powell, Nathaniel J; Jang, Albert; Park, Jang-Yeon; Valette, Julien; Garwood, Michael; Marjańska, Małgorzata

    2015-01-01

    To introduce a new outer volume suppression (OVS) technique that uses a single pulse and rotating gradients to accomplish frequency-swept excitation. This new technique, which is called gradient rotating outer volume excitation (GROOVE), produces a circular or elliptical suppression band rather than suppressing the entire outer volume. Theoretical and k-space descriptions of GROOVE are provided. The properties of GROOVE were investigated with simulations, phantom, and human experiments performed using a 4T horizontal bore magnet equipped with a TEM coil. Similar suppression performance was obtained in phantom and human brain using GROOVE with circular and elliptical shapes. Simulations indicate that GROOVE requires less SAR and time than traditional OVS schemes, but traditional schemes provide a sharper transition zone and less residual signal. GROOVE represents a new way of performing OVS in which spins are excited temporally in space on a trajectory that can be tailored to fit the shape of the suppression region. In addition, GROOVE is capable of suppressing tailored regions of space with more flexibility and in a shorter period of time than conventional methods. GROOVE provides a fast, low SAR alternative to conventional OVS methods in some applications (e.g., scalp suppression). © 2014 Wiley Periodicals, Inc.

  17. The Globular Cluster System of the Spiral Galaxy NGC 7814

    Science.gov (United States)

    Rhode, Katherine L.; Zepf, Stephen E.

    2003-11-01

    We present the results of a wide-field photometric study of the globular cluster (GC) system of the edge-on Sab spiral NGC 7814. This is the first spiral to be fully analyzed from our survey of the GC systems of a large sample of galaxies beyond the Local Group. NGC 7814 is of particular interest because a previous study estimated that it has 500-1000 GCs, giving it the largest specific frequency (SN) known for a spiral. Understanding this galaxy's GC system is important in terms of our understanding of the GC populations of spirals in general and has implications for the formation of massive galaxies. We observed the galaxy in BVR filters with the WIYN 3.5 m telescope and used image classification and three-color photometry to select GC candidates. We also analyzed archival Hubble Space Telescope (HST) Wide Field Planetary Camera 2 images of NGC 7814, both to help quantify the contamination level of the WIYN GC candidate list and to detect GCs in the inner part of the galaxy halo. Combining HST data with high-quality ground-based images allows us to trace the entire radial extent of this galaxy's GC system and determine the total number of GCs directly through observation. We find that rather than being an especially high-SN spiral, NGC 7814 has <~200 GCs and SN~1, making it comparable to the two most well-studied spiral galaxies, the Milky Way and M31. We explore the implications of these results for models of the formation of galaxies and their GC systems. The initial results from our survey suggest that the GC systems of typical elliptical galaxies can be accounted for by the merger of two or more spirals, but that for highly luminous elliptical galaxies, additional physical processes may be needed.

  18. Optimization of Flapping Airfoils for Maximum Thrust and Propulsive Efficiency

    Directory of Open Access Journals (Sweden)

    I. H. Tuncer

    2004-01-01

    Full Text Available A numerical optimization algorithm based on the steepest decent along the variation of the optimization function is implemented for maximizing the thrust and/or propulsive efficiency of a single flapping airfoil. Unsteady, low speed laminar flows are computed using a Navier-Stokes solver on moving overset grids. The flapping motion of the airfoil is described by a combined sinusoidal plunge and pitching motion. Optimization parameters are taken to be the amplitudes of the plunge and pitching motions, and the phase shift between them. Computations are performed in parallel in a work station cluster. The numerical simulations show that high thrust values may be obtained at the expense of reduced efficiency. For high efficiency in thrust generation, the induced angle of attack of the airfoil is reduced and large scale vortex formations at the leading edge are prevented. 

  19. Equivalence ratio and constriction effects on RBCC thrust augmentation

    Science.gov (United States)

    Koupriyanov, M.; Etele, J.

    2011-06-01

    A theoretical analysis of a variable area rocket based combined cycle engine with and without simultaneous mixing and combustion is presented. The flowfield is solved using a steady, quasi-one-dimensional, inviscid control volume formulation with combustion effects included via a generalized equilibrium calculation. Compression augmentation is shown to be sensitive to the equivalence ratio within the primary rocket chamber, where ejector section performance is greatest at both low and high equivalence ratios but near a minimum at stoichiometric conditions. The thrust generated by the RBCC engine compared to that generated by the same rocket in isolation can be increased by as much as 12% at constriction ratios of between 45% and 50%. Thrust augmentation is also shown to vary with equivalence ratio, where for a fixed geometry the maximum thrust is generated at equivalence ratios slightly below unity.

  20. Do cows prefer a barn compartment with a grooved or slotted floor

    NARCIS (Netherlands)

    Stefanowska, J.; Swierstra, D.; Berg, van den J.V.; Metz, J.H.M.

    2002-01-01

    Cow preferences for one of two compartments with different floors were tested in a barn with two symmetrical, connected compartments, each intended for 16 cows. Compartments were identical except for the floor. One floor was grooved longitudinally to the feeding barrier and the other was slotted

  1. Does loading influence the severity of cartilage degeneration in the canine groove-model of OA?

    NARCIS (Netherlands)

    Vos, P.; Intema, F.; El, B. van; Groot, J. de; Bijlsma, J.W.J.; Lafeber, F.; Mastbergen, S.

    2009-01-01

    Many animal models are used to study osteoarthritis (OA). In these models the role of joint loading in the development of OA is not fully understood. We studied the effect of loading on the development of OA in the canine Groove-model. In ten female beagle dogs OA was induced in one knee according

  2. Excitation of fluorescent nanoparticles by channel plasmon polaritons propagating in V-grooves

    DEFF Research Database (Denmark)

    Cuesta, Irene Fernandez; Nielsen, Rasmus Bundgaard; Boltasseva, Alexandra

    2009-01-01

    Recently, it has been proven that light can be squeezed into metallic channels with subwavelength lateral dimensions. Here, we present the study of the propagation of channel plasmon polaritons confined in gold V-grooves, filled with fluorescent particles. In this way, channel plasmon polaritons......-diameter beads, we show the possibility of individual excitation, what may have applications to develop very sensitive biosensors....

  3. High Excitation Efficiency of Channel Plasmon Polaritons in Tailored, UV-Lithography-Defined V-Grooves

    DEFF Research Database (Denmark)

    Smith, Cameron; Thilsted, Anil Haraksingh; Garcia-Ortiz, Cesar E.

    2014-01-01

    We demonstrate >50% conversion of light to V-groove channel plasmon-polaritons (CPPs) via compact waveguide-termination mirrors. Devices are fabricated using UV-lithography and crystallographic silicon etching. The V-shape is tailored by thermal oxidation to support confined CPPs....

  4. Measurement repeatability of tibial tuberosity-trochlear groove offset distance in red fox (Vulpes vulpes) cadavers

    NARCIS (Netherlands)

    Miles, J.E.; Jensen, B.R.; Kirpensteijn, J.; Svalastoga, E.L.; Eriksen, T.

    2013-01-01

    Abstract OBJECTIVE: To describe CT image reconstruction criteria for measurement of the tibial tuberosity-trochlear groove (TT-TG) offset distance, evaluate intra- and inter-reconstruction repeatability, and identify key sources of error in the measurement technique, as determined in vulpine hind

  5. Concerted intercalation and minor groove recognition of DNA by a homodimeric thiazole orange dye

    DEFF Research Database (Denmark)

    Bunkenborg, Jakob; Gadjev, N I; Deligeorgiev, T

    2000-01-01

    The thiazole orange dye TOTO binds to double-stranded DNA (dsDNA) by a sequence selective bis-intercalation. Each chromophore is sandwiched between two base pairs in a (5'-CpT-3'):(5'-ApG-3') site, and the linker spans two base pairs in the minor groove. We have used one- and two-dimensional NMR ...

  6. Different Thermodynamic Signatures for DNA Minor Groove Binding with Changes in Salt Concentration and Temperature

    OpenAIRE

    Wang, Shuo; Kumar, Arvind; Aston, Karl; Nguyen, Binh; Bashkin, James K.; Boykin, David W.; Wilson, W. David

    2013-01-01

    The effects of salt concentration and temperature on the thermodynamics of DNA minor groove binding have quite different signatures: binding enthalpy is salt concentration independent but temperature dependent. Conversely, binding free energy is salt dependent but essentially temperature independent through enthalpy-entropy compensation.

  7. Saying Hello World with GROOVE - A Solution to the TTC 2011 Instructive Case

    NARCIS (Netherlands)

    Ghamarian, A.H.; de Mol, M.J.; Rensink, Arend; Zambon, Eduardo; van Gorp, Pieter; Mazanek, Steffen; Rose, Louis

    2011-01-01

    This report presents a solution to the Hello World case study using GROOVE. We provide and explain the grammar that we used to solve the case study. Every requested question of the case study was solved by a single rule application.

  8. Saying Hello World with GROOVE - A Solution to the TTC 2011 Instructive Case

    Directory of Open Access Journals (Sweden)

    Amir Hossein Ghamarian

    2011-11-01

    Full Text Available This report presents a solution to the Hello World case study of TTC 2011 using GROOVE. We provide and explain the grammar that we used to solve the case study. Every requested question of the case study was solved by a single rule application.

  9. Ledges and grooves at γ/γ′ interfaces of single crystal superalloys

    Czech Academy of Sciences Publication Activity Database

    Parsa, A. B.; Wollgramm, P.; Buck, H.; Kostka, A.; Somsen, C.; Dlouhý, Antonín; Eggeler, G.

    2015-01-01

    Roč. 90, MAY (2015), s. 105-117 ISSN 1359-6454 R&D Projects: GA ČR(CZ) GA14-22834S Institutional support: RVO:68081723 Keywords : Ni-base single crystal superalloys * γ/γ′ interfaces * Interface dislocations * Rafting * Grooves Subject RIV: JG - Metallurgy Impact factor: 5.058, year: 2015

  10. Role of minor groove width and hydration pattern on amsacrine interaction with DNA.

    Directory of Open Access Journals (Sweden)

    Deepak K Jangir

    Full Text Available Amsacrine is an anilinoacridine derivative anticancer drug, used to treat a wide variety of malignancies. In cells, amsacrine poisons topoisomerase 2 by stabilizing DNA-drug-enzyme ternary complex. Presence of amsacrine increases the steady-state concentration of these ternary complexes which in turn hampers DNA replication and results in subsequent cell death. Due to reversible binding and rapid slip-out of amsacrine from DNA duplex, structural data is not available on amsacrine-DNA complexes. In the present work, we designed five oligonucleotide duplexes, differing in their minor groove widths and hydration pattern, and examined their binding with amsacrine using attenuated total reflection Fourier transform infrared (ATR-FTIR spectroscopy. Complexes of amsacrine with calf thymus DNA were also evaluated for a comparison. Our results demonstrate for the first time that amsacrine is not a simple intercalator; rather mixed type of DNA binding (intercalation and minor groove takes place between amsacrine and DNA. Further, this binding is highly sensitive towards the geometries and hydration patterns of different minor grooves present in the DNA. This study shows that ligand binding to DNA could be very sensitive to DNA base composition and DNA groove structures. Results demonstrated here could have implication for understanding cytotoxic mechanism of aminoacridine based anticancer drugs and provide directions to modify these drugs for better efficacy and few side-effects.

  11. Saying Hello World with GROOVE - A Solution to the TTC 2011 Instructive Case

    NARCIS (Netherlands)

    Ghamarian, A.H.; de Mol, M.J.; Rensink, Arend; Zambon, Eduardo; van Gorp, Pieter; Mazanek, Steffen; Rose, Louis

    This report presents a solution to the Hello World case study using GROOVE. We provide and explain the grammar that we used to solve the case study. Every requested question of the case study was solved by a single rule application.

  12. Effect of longitudinal grooves of the scallop surface on aerodynamic performance

    International Nuclear Information System (INIS)

    Kim, Tae Hun; Choi, Hae Cheon

    2008-01-01

    Some of the scallops like Amesium balloti have an excellent level-swimming ability, i.e. they can swim about 20m by single level swimming with a maximum swimming velocity of about 1.6m/s in the sea. On the other hand, some species like Patinopecten yessoensis have longitudinal grooves on the upper and lower surfaces and others do not. Therefore, in the present study, we measure the lift and drag forces on a real scallop model (Patinopecten yessoensis) in a wind tunnel. Experiments are performed at the Reynolds number of 75,000 based on the maximum chord length, which is within the swimming condition of real scallop (Re=30,000∼300,000). To see the effect of longitudinal grooves, we measure the aerodynamic forces on a scallop model by removing the grooves. With the grooves, the lift force increases at low angles of attack (α<10 .deg.). The drag force increases slightly at all the attack angles considered. The lift-to-drag ratio is increased by about 10% at α<10 .deg.

  13. Electron beam guiding by grooved SiO{sub 2} parallel plates without energy loss

    Energy Technology Data Exchange (ETDEWEB)

    Xue, Yingli; Yu, Deyang, E-mail: d.yu@impcas.ac.cn; Liu, Junliang; Zhang, Mingwu; Yang, Bian; Zhang, Yuezhao; Cai, Xiaohong [Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000 (China)

    2015-12-21

    Using a pair of grooved SiO{sub 2} parallel plates, stably guided electron beams were obtained without energy loss at 800–2000 eV. This shows that the transmitted electrons are guided by a self-organized repulsive electric field, paving the way for a self-adaptive manipulation of electron beams.

  14. Torque scaling in small-gap Taylor-Couette flow with smooth or grooved wall

    Science.gov (United States)

    Zhu, Bihai; Ji, Zengqi; Lou, Zhengkun; Qian, Pengcheng

    2018-03-01

    The torque in the Taylor-Couette flow for radius ratios η ≥0.97 , with smooth or grooved wall static outer cylinders, is studied experimentally, with the Reynolds number of the inner cylinder reaching up to Rei=2 ×105 , corresponding to the Taylor number up to Ta =5 ×1010 . The grooves are perpendicular to the mean flow, and similar to the structure of a submersible motor stator. It is found that the dimensionless torque G , at a given Rei and η , is significantly greater for grooved cases than smooth cases. We compare our experimental torques for the smooth cases to the fit proposed by Wendt [F. Wendt, Ing.-Arch. 4, 577 (1993), 10.1007/BF02084936] and the fit proposed by Bilgen and Boulos [E. Bilgen and R. Boulos, J Fluids Eng. 95, 122 (1973), 10.1115/1.3446944], which shows both fits are outside their range for small gaps. Furthermore, an additional dimensionless torque (angular velocity flux) N uω in the smooth cases exhibits an effective scaling of N uω˜T a0.39 in the ultimate regime, which occurs at a lower Taylor number, Ta ≈3.5 ×107 , than the well-explored η =0.714 case (at Ta ≈3 ×108 ). The same effective scaling exponent, 0.39, is also evident in the grooved cases, but for η =0.97 and 0.985, there is a peak before this exponent appears.

  15. Study on Burr Formation at the Top Edge in Rectangular Groove Cutting

    Directory of Open Access Journals (Sweden)

    Wen Jun Deng

    2012-01-01

    Full Text Available Previous research on burr formation in machining operations has usually been limited to the study of the rollover burr in the cutting direction. In this paper, a 3D finite element model to simulate rectangular groove cutting operation has been developed using commercial finite element software, employing experimentally determined mechanical properties at elevated strain rates and temperatures. The plastic deformation behavior and three-dimensional burr formation during rectangular groove cutting is investigated. The simulated burr profile and cutting force prove that the developed model can capture the thermo-mechanical mechanisms in rectangular groove cutting and can simulate burr development with considerable accuracy. The study concentrates on the influence of cutting parameters on burr formation which are also conducted. The results show that the feed rate and rake angle are the cutting parameters which have a major influence on burr size in the groove cutting operation. And the effect of cutting velocity and minor clearance angle in the traditional range on burr size are quite limited.

  16. Analysis of silt abrasion of the impeller ring in a centrifugal pump with J-grooves

    Science.gov (United States)

    Qian, Z. D.; Wang, Z. Y.; Guo, Z. W.; Dong, J.; Lu, J.

    2016-05-01

    The water flow and movement of silt in a prototype double-suction centrifugal pump was simulated using an Euler-Lagrange multiphase flow model. J-Grooves were adopted to protect the impeller ring from silt abrasion. The influence of J-grooves on the silt concentration and pump efficiency was analyzed. The results show that the radial component of the relative velocity around the impeller ring is too low to move the silt out of the spacing between the impeller plate and the casing. The high silt concentration around the impeller ring is the major contributor to silt abrasion of the impeller ring. The J-grooves induce two strong vortices, which increase the radial component of the relative velocity of water and reduce the silt concentration around the impeller ring, but additional friction losses are introduced and the pump efficiency is decreased. Optimization of the number and shape of J-grooves decreases losses in the efficiency of the pump, and effectively protects the impeller ring. Case 4 was found the most effective configuration in this study.

  17. TR-PIV measurement of the wake behind a grooved cylinder at low Reynolds number

    Science.gov (United States)

    Liu, Ying Zheng; Shi, Liu Liu; Yu, Jun

    2011-04-01

    A comparative study of the wakes behind cylinders with grooved and smooth surfaces was performed with a view to understand the wake characteristics associated with the adult Saguaro cacti. A low-speed recirculation water channel was established for the experiment; the Reynolds number, based on the free-stream velocity and cylinder diameter (D), was kept at ReD=1500. State-of-the-art time-resolved particle image velocimetry (TR-PIV) was employed to measure a total of 20 480 realizations of the wake field at a frame rate of 250 Hz, enabling a comprehensive view of the time- and phase-averaged wake pattern. In comparison to the wake behind the smooth cylinder, the length of the recirculation zone behind the grooved cylinder was extended by nearly 18.2%, yet the longitudinal velocity fluctuation intensity was considerably weakened. A global view of the peaked spectrum of the longitudinal velocity component revealed that the intermediate region for the grooved cylinder, which approximately corresponds to the transition region where the shear layer vortices interact, merge and shed before the formation of the Karman-like vortex street, was much wider than that for the smooth one. The unsteady events near St=0.3-0.4 were detected in the intermediate region behind the grooved cylinder, but no such events were found in the smooth cylinder system. Although the formation of the Karman-like vortex street was delayed by about 0.6D downstream for the grooved cylinder, no prominent difference in the vortex street region was found in the far wake for both cylinders. The Proper Orthogonal Decomposition (POD) method was used extensively to decompose the vector and swirling strength fields, which gave a close-up view of the vortices in the near wake. The first two POD modes of the swirling strength clarified the spatio-temporal characteristics of the shear layer vortices behind the grooved cylinder. The small-scale vortices superimposed on the shear layers behind the grooved cylinder

  18. Problems of millipound thrust measurement. The "Hansen Suspension"

    Energy Technology Data Exchange (ETDEWEB)

    Carta, David G.

    2014-03-31

    Considered in detail are problems which led to the need and use of the 'Hansen Suspension'. Also discussed are problems which are likely to be encountered in any low level thrust measuring system. The methods of calibration and the accuracies involved are given careful attention. With all parameters optimized and calibration techniques perfected, the system was found capable of a resolution of 10 {mu} lbs. A comparison of thrust measurements made by the 'Hansen Suspension' with measurements of a less sophisticated device leads to some surprising results.

  19. Robotic Pectoral Fin Thrust Vectoring Using Weighted Gait Combinations

    Directory of Open Access Journals (Sweden)

    John S. Palmisano

    2012-01-01

    Full Text Available A method was devised to vector propulsion of a robotic pectoral fin by means of actively controlling fin surface curvature. Separate flapping fin gaits were designed to maximize thrust for each of three different thrust vectors: forward, reverse, and lift. By using weighted combinations of these three pre-determined main gaits, new intermediate hybrid gaits for any desired propulsion vector can be created with smooth transitioning between these gaits. This weighted gait combination (WGC method is applicable to other difficult-to-model actuators. Both 3D unsteady computational fluid dynamics (CFD and experimental results are presented.

  20. Radial loads and axial thrusts on centrifugal pumps

    International Nuclear Information System (INIS)

    Anon.

    1986-01-01

    The proceedings of a seminar organised by the Power Industries Division of the IMechE are presented in this text. Complete contents: Review of parameters influencing hydraulic forces on centrifugal impellers; The effect of fluid forces at various operation conditions on the vibrations of vertical turbine pumps; A review of the pump rotor axial equilibrium problem - some case studies; Dynamic hydraulic loading on a centrifugal pump impeller; Experimental research on axial thrust loads of double suction centrifugal pumps; A comparison of pressure distribution and radial loads on centrifugal pumps; A theoretical and experimental investigation of axial thrusts within a multi-stage centrifugal pump

  1. Dynamic study of the larynx with spiral CT

    International Nuclear Information System (INIS)

    Park, Jong Yeon; Choi, Chang Ho; Yoon, Chi Soon; Kim, Yoon Gyoo; Nam, Sang Hwa; Kim, Kun Il; Kim, Byung Soo; Wang, Soo Guen

    1994-01-01

    It is essential to know the functional and morphologic changes of the larynx in the evaluation of laryngeal lesions. Conventional CT which has relatively long examination time is not suitable for this aim. The purposes of this study are to evaluate the capability of spiral CT in the dynamic study of the larynx and to know whether this new technique can replace conventional laryngography or not. Five healthy volunteers and 20 patients with laryngeal lesions underwent spiral dynamic CT scans with 3-dimensional reconstruction of the mucosal surface. A series of spiral CT scans were done while the volunteers performed various laryngeal positions to obtain the functional and morphologic information. The maneuvers used were: quite breathing, 'E' phonation, Valsalva maneuver, modified Valsalva maneuver, and a new method of our own, 'modified breath holding' technique. The patients were scanned when in quite breathing. Additional scans were obtained by using the 'modified breath holding' technique. The dynamic study with spiral CT could provide high resolutional images which nicely depicted the mobility of vocal cords and the mucosal changes of the laryngeal cavity in both healthy volunteer and patient groups. In patient group, the new 'modified breath holding' technique was easier and more reproducible than other maneuvers. Spiral CT allows a dynamic study of the larynx and can be a new alternative of laryngography

  2. On wave dark matter in spiral and barred galaxies

    Energy Technology Data Exchange (ETDEWEB)

    Martinez-Medina, Luis A.; Matos, Tonatiuh [Departamento de Física, Centro de Investigación y de Estudios Avanzados del IPN, A.P. 14-740, 07000 México D.F., México. (Mexico); Bray, Hubert L., E-mail: lmedina@fis.cinvestav.mx, E-mail: bray@math.duke.edu, E-mail: tmatos@fis.cinvestav.mx [Mathematics Department, Duke University, Box 90320, Durham, NC 27708 (United States)

    2015-12-01

    We recover spiral and barred spiral patterns in disk galaxy simulations with a Wave Dark Matter (WDM) background (also known as Scalar Field Dark Matter (SFDM), Ultra-Light Axion (ULA) dark matter, and Bose-Einstein Condensate (BEC) dark matter). Here we show how the interaction between a baryonic disk and its Dark Matter Halo triggers the formation of spiral structures when the halo is allowed to have a triaxial shape and angular momentum. This is a more realistic picture within the WDM model since a non-spherical rotating halo seems to be more natural. By performing hydrodynamic simulations, along with earlier test particles simulations, we demonstrate another important way in which wave dark matter is consistent with observations. The common existence of bars in these simulations is particularly noteworthy. This may have consequences when trying to obtain information about the dark matter distribution in a galaxy, the mere presence of spiral arms or a bar usually indicates that baryonic matter dominates the central region and therefore observations, like rotation curves, may not tell us what the DM distribution is at the halo center. But here we show that spiral arms and bars can develop in DM dominated galaxies with a central density core without supposing its origin on mechanisms intrinsic to the baryonic matter.

  3. Spiral scan long object reconstruction through PI line reconstruction

    International Nuclear Information System (INIS)

    Tam, K C; Hu, J; Sourbelle, K

    2004-01-01

    The response of a point object in a cone beam (CB) spiral scan is analysed. Based on the result, a reconstruction algorithm for long object imaging in spiral scan cone beam CT is developed. A region-of-interest (ROI) of the long object is scanned with a detector smaller than the ROI, and a portion of it can be reconstructed without contamination from overlaying materials. The top and bottom surfaces of the ROI are defined by two sets of PI lines near the two ends of the spiral path. With this novel definition of the top and bottom ROI surfaces and through the use of projective geometry, it is straightforward to partition the cone beam image into regions corresponding to projections of the ROI, the overlaying objects or both. This also simplifies computation at source positions near the spiral ends, and makes it possible to reduce radiation exposure near the spiral ends substantially through simple hardware collimation. Simulation results to validate the algorithm are presented

  4. Continuing research on the classical spiraling photon model

    Science.gov (United States)

    Li, Hongrui

    2014-11-01

    Based no the classical spiraling photon model proposed by Hongrui Li, the laws of reflection, refraction of a single photon can be derived. Moreover, the polarization, total reflection, evanescent wave and Goos-Hanchen shift of a single photon can be elucidated. However, this photon model is still unfinished. Especially, the spiraling diameter of a photon is not definite. In this paper, the continuous research works on this new theory are reported. According to the facts that the diffraction limit of light and the smallest diameter of the focal spot of lenses are all equal to the wavelength λ of the light, we can get that the spiraling diameter of a photon equals to the wavelength λ, so we gain that the angle between the linear velocity of the spiraling photon υ and the component of the linear velocity in the forward direction υb is 45°, and the energy of a classical spiraling photon E = (1/2)mυ2 = (1/2)m2c2 = mc2. This coincides with Einstein's mass-energy relation. While it is obtained that the velocity of the evanescent wave in the vacuum is slower than the velocity of light in glass in straight line. In such a way, the optical fiber can slow the light down. In addition, the force analysis of a single photon in optical tweezers system is discussed. And the reason that the laser beam can capture the particle slightly downstream from the focal point can be explained.

  5. On wave dark matter in spiral and barred galaxies

    International Nuclear Information System (INIS)

    Martinez-Medina, Luis A.; Matos, Tonatiuh; Bray, Hubert L.

    2015-01-01

    We recover spiral and barred spiral patterns in disk galaxy simulations with a Wave Dark Matter (WDM) background (also known as Scalar Field Dark Matter (SFDM), Ultra-Light Axion (ULA) dark matter, and Bose-Einstein Condensate (BEC) dark matter). Here we show how the interaction between a baryonic disk and its Dark Matter Halo triggers the formation of spiral structures when the halo is allowed to have a triaxial shape and angular momentum. This is a more realistic picture within the WDM model since a non-spherical rotating halo seems to be more natural. By performing hydrodynamic simulations, along with earlier test particles simulations, we demonstrate another important way in which wave dark matter is consistent with observations. The common existence of bars in these simulations is particularly noteworthy. This may have consequences when trying to obtain information about the dark matter distribution in a galaxy, the mere presence of spiral arms or a bar usually indicates that baryonic matter dominates the central region and therefore observations, like rotation curves, may not tell us what the DM distribution is at the halo center. But here we show that spiral arms and bars can develop in DM dominated galaxies with a central density core without supposing its origin on mechanisms intrinsic to the baryonic matter

  6. Effectiveness of various irrigation protocols for the removal of calcium hydroxide from artificial standardized grooves

    Directory of Open Access Journals (Sweden)

    Hakan GOKTURK

    Full Text Available Abstract Objective The aim of this study was to investigate the ability of laser-activated irrigation (LAI, XP-endo Finisher, CanalBrush, Vibringe, passive ultrasonic irrigation (PUI, and conventional syringe irrigation systems on the removal of calcium hydroxide (CH from simulated root canal irregularities. Material and Methods The root canals of one hundred and five extracted single-rooted teeth were instrumented using Reciproc rotary files up to size R40. The teeth were split longitudinally. Two of the three standard grooves were created in the coronal and apical section of one segment, and another in the middle part of the second segment. The standardized grooves were filled with CH and the root halves were reassembled. After 14 days, the specimens were randomly divided into 7 experimental groups (n=15/group. CH was removed as follows: Group 1: beveled needle irrigation; Group 2: double side-vented needle irrigation; Group 3: CanalBrush; Group 4: XP-endo Finisher; Group 5: Vibringe; Group 6: PUI; Group 7: LAI. The amount of remaining CH in the grooves was scored under a stereomicroscope at 20× magnification. Statistical evaluation was performed using Kruskal–Wallis and Bonferroni-Correction Mann–Whitney U tests. Results Groups 1 and 2 were the least efficient in eliminating CH from the grooves. Groups 6 and 7 eliminated more CH than the other protocols; however, no significant differences were found between these two groups (P>.05. Conclusions Nevertheless, none of the investigated protocols were able to completely remove all CH from all three root regions. LAI and PUI showed less residual CH than the other protocols from artificial grooves.

  7. Extending the GANIL control system for the SPIRAL project

    International Nuclear Information System (INIS)

    Lecorche, E.

    1997-01-01

    The SPIRAL project under construction at GANIL aims to deliver radioactive ion beams to the physicists by the end of 1998. In 1996, it has been proposed to achieve most of the SPIRAL control system as an extension of the system currently in use at GANIL. Therefore the main features of the GANIL control system design are first recalled. Then the paper shows how the GANIL control system should have been upgraded and extended to integrate the SPIRAL project. This evolution had to cope with the specific needs brought by the new machine and to consider the size of the project which is around one third of the GANIL control system volume. Lastly current status of the system is given. (author)

  8. Spiral waves in the Belousov-Zhabotinskii reaction

    Science.gov (United States)

    Keener, James P.; Tyson, John J.

    1986-09-01

    The beautiful spiral waves of oxidation in the Belousov-Zhabotinskii reaction are the source of many interesting and important questions about periods structures in excitable media. It has long been known that these spirals are similar to involutes of circles, at least some distance from the center, but until now, no way has been known to determine the correct wavelength and frequency. In this paper, we show that the parameters of a spiral wave can be viwed s eigenvalues of a problem with unique solution. The critical ingredients of the theory are the effects of curvature on the propagation of wavefronts in two-dimensional media, and the dispersion of plane waves Our analytical results are shown to be in good agreement with experimental data for the Belousov-Zhabotinskii reagent.

  9. A Twin Spiral Planar Antenna for UWB Medical Radars

    Directory of Open Access Journals (Sweden)

    Giuseppe A. Zito

    2013-01-01

    Full Text Available A planar-spiral antenna to be used in an ultrawideband (UWB radar system for heart activity monitoring is presented. The antenna, named “twin,” is constituted by two spiral dipoles in a compact structure. The reflection coefficient at the feed point of the dipoles is lower than −8 dB over the 3–12 GHz band, while the two-dipoles coupling is about −20 dB. The radiated beam is perpendicular to the plane of the spiral, so the antenna is wearable and it may be an optimal radiator for a medical UWB radar for heart rate detection. The designed antenna has been also used to check some hypotheses about the UWB radar heart activity detection mechanism. The radiation impedance variation, caused by the thorax vibrations associated with heart activity, seems to be the most likely explanation of the UWB radar operation.

  10. The scientific objectives of the SPIRAL 2 Project

    International Nuclear Information System (INIS)

    Ackermann, D.; Adoui, L.; Angelis, G. de

    2006-06-01

    The construction of SPIRAL 2 at GANIL will open completely new possibilities for parallel beam operation of the whole facility. The whole GANIL/SPIRAL/SPIRAL2 accelerator complex will allow for the simultaneous use of up to 5 different radioactive and stable beams. Several combinations of different beams delivered in parallel for experiments at low (keV/u), medium (few MeV/u) and high (up to 100 MeV/u) energies will be possible. Presently the GANIL/SPIRAL facility delivers about 60 weeks per year of stable and radioactive beams (up to 3 simultaneous beams). Thanks to SPIRAL 2 and the construction of a new beam line connecting the CIME cyclotron and the G1 and G2 experimental rooms the available beam time for experiments may be extended up to about 120 (up to 5 simultaneous beams) weeks per year. The chapters which follow a general introduction deal with the detailed questions to be addressed by experiments with the beams from SPIRAL2. In chapter 2 the many unanswered questions related to the structure of exotic nuclei are posed and the role of SPIRAL2 in answering them outlined. Chapter 3 deals with the dynamics and thermodynamics of asymmetric nuclear systems. Chapter 4 is concerned with questions of nuclear astrophysics which are intimately related to the properties of exotic nuclei. Chapter 5 indicates how the atomic nucleus can act as a laboratory for tests of the Standard model of Particle Physics and Chapter 6 shows how the production of intense fluxes of neutrons at SPIRAL2 make it an excellent tool to address both questions related to damage in materials of importance in nuclear installations and to the s- and r-processes of nucleosynthesis. In chapter 7 we turn to the application, of the radioactive beams from SPIRAL2 and the radionuclides produced by it, to study condensed matter and radiobiology. Finally in the eight and last chapter the reader can find an account of the historical development of the SPIRAL2 facility and this is followed by an outline of

  11. The scientific objectives of the SPIRAL 2 Project

    Energy Technology Data Exchange (ETDEWEB)

    Ackermann, D.; Adoui, L.; Angelis, G. de [GANIL, Grand Accelerateur National d' Ions Lourds, BP 55027, 14076 Caen cedex 5 (France)] (and others)

    2006-06-15

    The construction of SPIRAL 2 at GANIL will open completely new possibilities for parallel beam operation of the whole facility. The whole GANIL/SPIRAL/SPIRAL2 accelerator complex will allow for the simultaneous use of up to 5 different radioactive and stable beams. Several combinations of different beams delivered in parallel for experiments at low (keV/u), medium (few MeV/u) and high (up to 100 MeV/u) energies will be possible. Presently the GANIL/SPIRAL facility delivers about 60 weeks per year of stable and radioactive beams (up to 3 simultaneous beams). Thanks to SPIRAL 2 and the construction of a new beam line connecting the CIME cyclotron and the G1 and G2 experimental rooms the available beam time for experiments may be extended up to about 120 (up to 5 simultaneous beams) weeks per year. The chapters which follow a general introduction deal with the detailed questions to be addressed by experiments with the beams from SPIRAL2. In chapter 2 the many unanswered questions related to the structure of exotic nuclei are posed and the role of SPIRAL2 in answering them outlined. Chapter 3 deals with the dynamics and thermodynamics of asymmetric nuclear systems. Chapter 4 is concerned with questions of nuclear astrophysics which are intimately related to the properties of exotic nuclei. Chapter 5 indicates how the atomic nucleus can act as a laboratory for tests of the Standard model of Particle Physics and Chapter 6 shows how the production of intense fluxes of neutrons at SPIRAL2 make it an excellent tool to address both questions related to damage in materials of importance in nuclear installations and to the s- and r-processes of nucleosynthesis. In chapter 7 we turn to the application, of the radioactive beams from SPIRAL2 and the radionuclides produced by it, to study condensed matter and radiobiology. Finally in the eight and last chapter the reader can find an account of the historical development of the SPIRAL2 facility and this is followed by an outline of

  12. Study on a new water purification equipment with spiral lamellas

    Science.gov (United States)

    Feng, X. R.

    2017-08-01

    A new water purification equipment was introduced, especially the section of spiral lamellas. Utilization of spiral lamellas made the sedimentation space reach to 100%, not only improving sedimentation efficiency and reducing the cover space, but also saving investment. Production test results showed that the new water purification equipment with spiral lamellas had characteristics of excellent treatment efficiency and high shock resistant capacity. As the treatment water volume was 240 m3/d, when the turbidity, CODMn and UV254 were 203 NTU, 1.90 mg/L and 0.030 cm-1 in raw water, they were 0.32 NTU, 0.72mg/L and 0.011 cm-1 respectively in effluent water, which could fully meet the drinking water hygiene requirement.

  13. A Spiral And Discipline-Oriented Curriculum In Medical Imaging

    DEFF Research Database (Denmark)

    Wilhjelm, Jens E.; Hanson, Lars G.; Henneberg, Kaj-Åge

    2011-01-01

    This contribution describes and evaluates an experimental combination of a spiral and discipline-oriented curriculum implemented in the bachelor’s and master’s program in Medicine and Technology. The implementation in the master’s program is in the form of a study line in Medical Imaging and Radi......This contribution describes and evaluates an experimental combination of a spiral and discipline-oriented curriculum implemented in the bachelor’s and master’s program in Medicine and Technology. The implementation in the master’s program is in the form of a study line in Medical Imaging...... and Radiation Physics containing three disciplines: Imaging modalities, Radiation therapy and Image processing. The two imaging courses in the bachelor’s program and the first imaging course in the master’s program follow a spiral curriculum in which most disciplines are encountered in all courses...

  14. Auditory Mechanics of the Tectorial Membrane and the Cochlear Spiral

    Science.gov (United States)

    Gavara, Núria; Manoussaki, Daphne; Chadwick, Richard S.

    2012-01-01

    Purpose of review This review is timely and relevant since new experimental and theoretical findings suggest that cochlear mechanics from the nanoscale to the macroscale are affected by mechanical properties of the tectorial membrane and the spiral shape. Recent findings Main tectorial membrane themes covered are i) composition and morphology, ii) nanoscale mechanical interactions with the outer hair cell bundle, iii) macroscale longitudinal coupling, iv) fluid interaction with inner hair cell bundles, v) macroscale dynamics and waves. Main cochlear spiral themes are macroscale low-frequency energy focusing and microscale organ of Corti shear gain. Implications Findings from new experimental and theoretical models reveal exquisite sensitivity of cochlear mechanical performance to tectorial membrane structural organization, mechanics, and its positioning with respect to hair bundles. The cochlear spiral geometry is a major determinant of low frequency hearing. Suggestions are made for future research directions. PMID:21785353

  15. Spiral CT for cervical lymph node enlargement. Early clinical results

    International Nuclear Information System (INIS)

    Steinkamp, H.J.; Keske, U.; Schedel, J.; Hosten, N.; Felix, R.

    1994-01-01

    Spiral CT was performed before treatment in 35 patients with suspected cervical lymph node enlargement. By coronary and sagittal reconstruction it is possible to utilise the M/Q quotient which has become accepted as the result of sonographic and MRI examinations. It is now possible to obtain high diagnostic accuracy (97%) for distinguishing between reactive change from metastatic infiltration of lymph nodes (>8 mm) by using CT. Using spiral CT with 5 mm table movement, three patients diagnosed as stage N1 by axial CT were shown to be N2b. This represents a highly sensitive and highly specific method of lymph node diagnosis. Further diagnostic improvement derives from the ability to relate the lymph nodes to surrounding tissues. Spiral CT is also suitable for defining other space occupying lesions, e.g., the exact extent of retropharyngeal abscesses, abnormalities of the salivary glands or laryngocoeles. (orig.)

  16. The interaction between deepwater channel systems and growing thrusts and folds, toe-thrust region of the deepwater Niger Delta

    Science.gov (United States)

    Jolly, B.; Lonergan, L.; Whittaker, A.

    2012-04-01

    Gravity-driven seaward-verging thrusts, landward-verging back-thrusts and associated folds often characterize the slope and deepwater settings of passive margins. These structures, found in the "toe-thrust" region of the system, exert a significant control on sediment gravity flows because they create and determine the location and configuration of sediment depocentres and transport systems. However, to fully understand the interaction between sediment gravity flows and seabed topography we need to evaluate and quantify the geomorphic response of sub-marine channels to faulting in an area where the degree of tectonic shortening can be well constrained. This study exploits 3D seismic data in the outer toe-thrust region of the deepwater Niger Delta to analyze the interaction between Plio-Pleistocene channel systems and actively growing folds and thrusts. We first mapped folds and thrusts from the seismic data and we used this data to reconstruct the history of fold growth. We then used the sea-bed seismic horizon to build a 50 m resolution Digital Elevation Model (DEM) of the sea floor in Arc-GIS. From the DEM, we extracted channel long profiles across growing structures for both the current channel thalwegs and for the associated channel cut-and-fill sequences identified from the seismic data. We measured channel geometry at regular intervals along the channel length to evaluate system response to tectonic perturbation, and we used this data to help us approximate the down-system distribution of bed shear stress, and hence incision capacity. Initial results show that changes in submarine channel longitudinal profiles are directly correlated to underlying seabed thrusts and folds. Channels gradients are typically linear to slightly concave, and have an average gradient of 0.90. Actively growing thrusts are associated with a local steepening in channel gradient (up to 200% change), which typically extends 0.5 to 2 km upstream of the fault. Within these "knickzones

  17. Getting into the GROOVE: How Building Effective Education Partnerships and Promoting Authentic Student Research through the Girls' Remotely Operated Ocean Vehicle Exploration (GROOVE) Workshop.

    Science.gov (United States)

    Pelz, M.; Heesemann, M.; Hoeberechts, M.

    2017-12-01

    This presentation outlines the pilot year of Girls' Remotely Operated Ocean Vehicle Exploration or GROOVE, a hands-on learning program created collaboratively with education partners Ocean Networks Canada and St. Margaret's School (Victoria, BC, Canada). The program features student-led activities, authentic student experiences, clearly outlined learning outcomes, teacher and student self-assessment tools, and curriculum-aligned content. Presented through the lens of STEM, students build a modified Seaperch ROV and explore and research thematic scientific concepts such as buoyancy, electronic circuitry, and deep-sea exploration. Further, students learn engineering skills such as isotropic scaling, soldering, and assembly as they build their ROV. Ocean Networks Canada (ONC), an initiative of the University of Victoria, develops, operates, and maintains cabled ocean observatory systems. These include technologies developed on the world-leading NEPTUNE and VENUS observatories and the ever-expanding network of community observatories in the Arctic and coastal British Columbia. These observatories, large and small, enable communities, users, scientists, teachers, and students to monitor real-time and historical data from the local marine environment from anywhere on the globe. GROOVE, Girls' Remotely Operated Ocean Vehicle Exploration, is ONC's newest educational program and is related to their foundational program K-12 Ocean Sense educational program. This presentation will share our experiences developing, refining, and assessing our efforts to implement GROOVE using a train-the-trainer model aimed at formal and informal K-12 educators. We will highlight lessons learned from multiple perspectives (students, participants, developers, and mentors) with the intent of informing future education and outreach initiatives.

  18. Engineering Research, Development and Technology, FY95: Thrust area report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    The mission of the Engineering Research, Development, and Technology Program at Lawrence Livermore National Laboratory (LLNL) is to develop the knowledge base, process technologies, specialized equipment, tools and facilities to support current and future LLNL programs. Engineering`s efforts are guided by a strategy that results in dual benefit: first, in support of Department of Energy missions, such as national security through nuclear deterrence; and second, in enhancing the nation`s economic competitiveness through their collaboration with US industry in pursuit of the most cost-effective engineering solutions to LLNL programs. To accomplish this mission, the Engineering Research, Development, and Technology Program has two important goals: (1) identify key technologies relevant to LLNL programs where they can establish unique competencies, and (2) conduct high-quality research and development to enhance their capabilities and establish themselves as the world leaders in these technologies. To focus Engineering`s efforts, technology thrust areas are identified and technical leaders are selected for each area. The thrust areas are comprised of integrated engineering activities, staffed by personnel from the nine electronics and mechanical engineering divisions, and from other LLNL organizations. This annual report, organized by thrust area, describes Engineering`s activities for fiscal year 1995. The report provides timely summaries of objectives methods, and key results from eight thrust areas: computational electronics and electromagnetics; computational mechanics; microtechnology; manufacturing technology; materials science and engineering; power conversion technologies; nondestructive evaluation; and information engineering.

  19. Development Status of High-Thrust Density Electrostatic Engines

    Science.gov (United States)

    Patterson, Michael J.; Haag, Thomas W.; Foster, John E.; Young, Jason A.; Crofton, Mark W.

    2017-01-01

    Ion thruster technology offers the highest performance and efficiency of any mature electric propulsion thruster. It has by far the highest demonstrated total impulse of any technology option, demonstrated at input power levels appropriate for primary propulsion. It has also been successfully implemented for primary propulsion in both geocentric and heliocentric environments, with excellent ground/in-space correlation of both its performance and life. Based on these attributes there is compelling reasoning to continue the development of this technology: it is a leading candidate for high power applications; and it provides risk reduction for as-yet unproven alternatives. As such it is important that the operational limitations of ion thruster technology be critically examined and in particular for its application to primary propulsion its capabilities relative to thrust the density and thrust-to-power ratio be understood. This publication briefly addresses some of the considerations relative to achieving high thrust density and maximizing thrust-to-power ratio with ion thruster technology, and discusses the status of development work in this area being executed under a collaborative effort among NASA Glenn Research Center, the Aerospace Corporation, and the University of Michigan.

  20. The Effect of Atmospheric Pressure on Rocket Thrust -- Part I.

    Science.gov (United States)

    Leitner, Alfred

    1982-01-01

    The first of a two-part question asks: Does the total thrust of a rocket depend on the surrounding pressure? The answer to this question is provided, with accompanying diagrams of rockets. The second part of the question (and answer) are provided in v20 n7, p479, Oct 1982 of this journal. (Author/JN)

  1. Operant Control of Pathological Tongue Thrust in Spastic Cerebral Palsy.

    Science.gov (United States)

    Thompson, George A., Jr.

    1979-01-01

    The behavior modification procedure, carried out at mealtime with a ten-year-old retarded boy who had spastic cerebral palsy, consisted of differential reinforcement and punishment, and resulted in substantial decreases in tongue thrust (reverse swallowing) and food expulsion, and a large increase in observed chewing. (Author/DLS)

  2. 14 CFR 33.79 - Fuel burning thrust augmentor.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel burning thrust augmentor. 33.79 Section 33.79 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Design and Construction; Turbine Aircraft Engines § 33.79 Fuel burning...

  3. 14 CFR 33.73 - Power or thrust response.

    Science.gov (United States)

    2010-01-01

    ....73 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Design and Construction; Turbine Aircraft Engines § 33.73 Power or thrust response. The design and construction of the engine must enable an increase— (a) From minimum to...

  4. Back-thrusting in Lesser Himalaya: Evidences from magnetic fabric ...

    Indian Academy of Sciences (India)

    Back-thrusting in Lesser Himalaya: Evidences from magnetic fabric studies in parts of Almora crystalline zone, Kumaun Lesser Himalaya. Amar Agarwal, K K Agarwal, R Bali, Chandra Prakash and Gaurav Joshi. Supplementary data. Table S1. AMS data, representing mean of values from cores (N) collected from each site ...

  5. Experiments on the Thrust of a Synthetic Jet in Crossflow

    Science.gov (United States)

    Ayers, Bradley; Henoch, Charles; Johari, Hamid

    2014-11-01

    A set of water tunnel experiments were conducted to investigate the effect of crossflow on the thrust of a synthetic jet. This research was motivated by the desire to generate significant turning moments on a fully-submerged, supercavitating vehicle without using control fins or canards. The water tunnel model was a sting-mounted, 3-inch diameter cylindrical body interfaced to a 6-axis waterproof load cell. The synthetic jet actuator was contained within the model and the jet orifice located near the aft end of the model was oriented perpendicular to the mean flow. The actuator consisted of an externally controlled solenoid driving a piston into the cavity. The jet thrust was measured over a broad range of synthetic jet operating parameters, including the actuation frequency and duty cycle, as well as the jet-to-crossflow velocity ratios. Previous work which is based on the slug flow model of an individual vortex ring predicts the time-averaged thrust scales with the square of actuation frequency and the stroke length. The measurements will be compared with the theoretical predictions, and the results will be used to assess the effect of crossflow on the thrust of synthetic jet. Sponsored by the ONR-ULI program.

  6. Critical Pressures of the Thrust Bearing Using a Magnetic Fluid

    OpenAIRE

    長屋, 幸助; 武田, 定彦; 佐藤, 淳; 井開, 重男; 関口, 肇; 斉藤, 登

    1990-01-01

    This paper proposes a thrust bearing lubricated by a magnetic fluid under a magnetic field. The critical pressures of the bearing versus the magnitude of the magnetic flux densities have been investigated experimentally. It is clarified that the critical pressures of the proposed bearing are larger than those of the normal lubricant bearing under high speeds.

  7. Investigation on Thrust and Moment Coefficients of a Centrifugal Turbomachine

    Directory of Open Access Journals (Sweden)

    Bo Hu

    2018-04-01

    Full Text Available In radial pumps and turbines, the centrifugal through-flow in both the front and the back chambers is quite common. It strongly impacts the core swirl ratio, pressure distribution, axial thrust and frictional torque. In order to investigate these relationships experimentally, a test rig was designed at the University of Duisburg-Essen and described in this paper. Based on both the experimental and numerical results, correlations are determined to predict the impacts of the centrifugal through-flow on the core swirl ratio, the thrust coefficient and the moment coefficient. Two correlations respectively are determined to associate the core swirl ratio with the local through-flow coefficient for both Batchelor type flow and Stewartson type flow. The correlations describing the thrust coefficient and the moment coefficient in a rotor-stator cavity with centripetal through-flow (Hu et al., 2017 are modified for the case of centrifugal through-flow. The Daily and Nece diagram distinguishing between different flow regimes in rotor-stator cavities is extended with a through-flow coordinate into 3D. The achieved results provide a comprehensive data base which is intended to support the calculation of axial thrust and moment coefficients during the design process of radial pumps and turbines in a more accurate manner.

  8. Duplex geometry: an example from the Moine Thrust Belt

    Science.gov (United States)

    Bowler, S.

    1987-04-01

    The geometry and microstructure of a small duplex formed in one bed from the Moine Thrust Belt of northwest Scotland is reported. The structure is seen in oblique section, within the Cambrian Pipe-rock, in an area of low strain. A range of movement direction indicators are present in the structure. An early grain shape fabric developed close to the roof thrust is taken as the best estimate of the overall movement direction towards 287°. Slickensides in the gouge developed on movement planes within the duplex show varied orientations on a given plane, and are not considered useful indicators of thrust transport direction. Branch lines exposed converge and diverge, suggesting little lateral continuity of the exposed structure. The microstructures present within the structure indicate an increase in localised deformation, and in cataclastic behavior as the duplex evolved. Early layer parallel shear is ubiquitous, giving rise to an elongate grain shape fabric close to bedding surfaces. In early formed horses, a layer-parallel, oblate grain shape fabric, which shows localised slip zones, is overprinted by gouge formation. Later formed horses show only fracturing and gouge development. This sequence is attributed to stick-slip behavior in the propagation or displacement of the original fault, now the floor thrust.

  9. Structures and morphotectonic evolution of the frontal fold–thrust ...

    Indian Academy of Sciences (India)

    52

    The differential movement of the mountain front on both sides of the ramp is decipherable. 23. This is especially true ..... Further movement along the Frontal Fault deformed Siwalik sediments. Siwalik sediments ..... Poblet J and Lisle R J 2011 Kinematic evolution and structural styles of fold-and-thrust belts;. 391. Geol. Soc.

  10. Thrust generation and wake structure for flow across a pitching ...

    Indian Academy of Sciences (India)

    ... not a sufficient condition for the generation of thrust. The vortex strength is found to be invariant of the pitching frequency. Certain differences from the reported results are noted, which may be because of difference in the airfoil shape. These results can help improve understanding of the flow behavior as the low Reynolds ...

  11. Rediscovering the Giant Low Surface Brightness Spiral Galaxy Malin 1

    Science.gov (United States)

    Galaz, Gaspar

    2018-01-01

    I summarize the latest discoveries regarding this ramarkable diffuse and giant galaxy, the largest single spiral in the universe so far. I describe how the latest discoveries could have been done easily 20 years ago, but an incredible summation of facts and some astronomical sociology, keeped many of them undisclosed. I present the most conspicuous features of the giant spiral arms of Malin 1, including stellar density, colors, stellar populations and some modeling describing their past evolution to the current state. I conclude with pending issues regarding stellar formation in Malin 1, and the efforts to detect its elusive molecular gas.

  12. Initial clinical experience with spiral CT angiography in the abdomen

    International Nuclear Information System (INIS)

    Gaa, J.; Stehling, M.K.; Costello, P.

    1993-01-01

    The latest developments in modern CT instruments, offering scanning times of a second, opened up new possibilities in CT imaging in combination with the spiral technique. The data set normally taken with single-breath-hold technique is free of respiratory artefacts and thus is a good basis for accurate 3D image reconstruction. Spiral CTA allows a non-invasive 3D imaging of various blood vessels. Patients with abdominal aortic aneurysms of aorto-iliac bypass can be examined as outpatients within 15 minutes. (orig.) [de

  13. The color gradient in spiral galaxies: application to M 81

    International Nuclear Information System (INIS)

    Segalovitz, A.

    1975-01-01

    The calculated development of the color of a star cluster is used to predict the expected color evolution, as a function of radius, in a spiral galaxy. It is assumed that the fraction of gas which is converted into stars during a spiral arm passage is a function of radius only. Applying this model to M 81, it is shown that the observed color and mass distributions can be explained by an initial disk-like gas distribution proportional to the inverse square of the radius and a consumption fraction which is an increasing function of radius. (orig.) [de

  14. Spiral CT angiography of the abdominal aorta and its branches

    Energy Technology Data Exchange (ETDEWEB)

    Costello, P. [Dept. of Radiology, Deaconess Hospital and Harvard Medical School, Boston, MA (United States); Gaa, J. [Dept. of Radiology, Deaconess Hospital and Harvard Medical School, Boston, MA (United States)

    1993-08-01

    Spiral CT angiography (CTA) was performed on 19 patients for the pre-operative assessment of abdominal aortic aneurysms and in 3 post-operative renal artery bypass patients. Spiral CTA performed during intravenous contrast infusion provided a volume of data that was reconstructed at thin increments. Images were edited and reformatted either as surface rendered three-dimensional or maximum intensity projection (MIP) displays. Final images were viewed in a cine-loop presentation of quality comparable to conventional angiograms. The entire aorta can be examined from the coeliac axis to mid-pelvis with only 107 ml of 60% contrast. (orig.)

  15. SPIRAL2 Week 2011 - Slides of the presentations

    International Nuclear Information System (INIS)

    Gales, S.; Jacquemet, M.; Lewitowicz, M.; Petit, E.; Biarrote, J.L.; Uriot, D.; Thuillier, T.; Peaucelle, C.; Barue, C.; Van Hille, C.; Bernaudin, P.E.; Galdemard, P.; Ausset, P.; Dolegieviez, P.; Levallois, R.; Marchetto, M.; Pasini, M.; Quiclet, M.; Danna, O.; Lunney, D.; Di Giacomo, M.

    2013-01-01

    The main goal of the meeting is to present and discuss the current status of the SPIRAL2 project at GANIL in front of a large community of scientists and engineers. The program of the meeting will include presentations on scientific and technical developments related to the baseline project, experiments and theory. The main topics to be discussed at the conference have been: -) Driver Accelerators, -) Production of radioactive ion beams (RIB), -) Safety, -) RIB Facilities Worldwide (FAIR, Riken Nishina Center, SPES project, FRIB project) -) FP7 SPIRAL2 Preparatory Phase, -) Experiments with RIB and Theory. This document is made up of the slides of the presentations

  16. Necessity for High Accuracy Rotation Curves in Spiral Galaxies

    OpenAIRE

    Blais-Ouellette, Sebastien; Carignan, Claude; Amram, Philippe

    1998-01-01

    In the last 20 years, rotation curves derived from H I kinematics obtained on radio synthesis instruments were used to probe the dark matter distribution in spiral and dwarf irregular galaxies. It is shown, with the aid of the Sd galaxy NGC 5585, that high resolution 2--D H II kinematics is necessary to determine accurately the mass distribution of spirals. New CFHT Fabry--Perot Hff observations are combined with low resolution Westerbork H I data to study its mass distribution. Using the com...

  17. A Spiral And Discipline-Oriented Curriculum In Medical Imaging

    DEFF Research Database (Denmark)

    Wilhjelm, Jens E.; Hanson, Lars G.; Henneberg, Kaj-Åge

    2011-01-01

    This contribution describes and evaluates an experimental combination of a spiral and discipline-oriented curriculum implemented in the bachelor’s and master’s program in Medicine and Technology. The implementation in the master’s program is in the form of a study line in Medical Imaging...... and Radiation Physics containing three disciplines: Imaging modalities, Radiation therapy and Image processing. The two imaging courses in the bachelor’s program and the first imaging course in the master’s program follow a spiral curriculum in which most disciplines are encountered in all courses...

  18. Resonant fields created by spiral electric currents in Tokamaks

    International Nuclear Information System (INIS)

    Fernandes, A.S.; Caldas, I.L.

    1985-01-01

    The influence of the resonant magnetic perturbations, created by electric currents in spirals, on the plasma confinement in a tokamak with circular section and large aspect ratio is investigated. These perturbations create magnetic islands around the rational magnetic surface which has the helicity of the helicoidal currents. The intensities of these currents are calculated in order to the magnetic islands reach the limiter or others rational surfaces, what could provoke the plasma disrupture. The electric current intensities are estimated, in two spiral sets with different helicities, which create a predominantly stocastic region among the rational magnetic surfaces with these helicities. (L.C.) [pt

  19. Performance of Simple Gas Foil Thrust Bearings in Air

    Science.gov (United States)

    Bruckner, Robert J.

    2012-01-01

    Foil bearings are self-acting hydrodynamics devices used to support high speed rotating machinery. The advantages that they offer to process fluid lubricated machines include: high rotational speed capability, no auxiliary lubrication system, non-contacting high speed operation, and improved damping as compared to rigid hydrodynamic bearings. NASA has had a sporadic research program in this technology for almost 6 decades. Advances in the technology and understanding of foil journal bearings have enabled several new commercial products in recent years. These products include oil-free turbochargers for both heavy trucks and automobiles, high speed electric motors, microturbines for distributed power generation, and turbojet engines. However, the foil thrust bearing has not received a complimentary level of research and therefore has become the weak link of oil-free turbomachinery. In an effort to both provide machine designers with basic performance parameters and to elucidate the underlying physics of foil thrust bearings, NASA Glenn Research Center has completed an effort to experimentally measure the performance of simple gas foil thrust bearing in air. The database includes simple bump foil supported thrust bearings with full geometry and manufacturing techniques available to the user. Test conditions consist of air at ambient pressure and temperatures up to 500 C and rotational speeds to 55,000 rpm. A complete set of axial load, frictional torque, and rotational speed is presented for two different compliant sub-structures and inter-pad gaps. Data obtained from commercially available foil thrust bearings both with and without active cooling is presented for comparison. A significant observation made possible by this data set is the speed-load capacity characteristic of foil thrust bearings. Whereas for the foil journal bearing the load capacity increases linearly with rotational speed, the foil thrust bearing operates in the hydrodynamic high speed limit. In

  20. Investigation of the influence of radial grooves on the flow in an eccentrically deposited annulus using CFD numerical simulation

    Directory of Open Access Journals (Sweden)

    Bojko Marian

    2014-03-01

    Full Text Available This paper evaluates the influence of radial grooves in the eccentrically deposited annulus using by mathematical modeling of fluid flow through each grooves. The inner cylinder (rotor is eccentrically deposited and its movement is composed of two movements (rotation and precession. The outer cylinder is stationary and has radial grooves. In the first phase is defined a mathematical model of the flow, which is then applied to the 3D model of narrow gap with radial grooves. In this paper are present several variants of the computational domain with regard to the number of radial grooves. Based on the results of numerical simulations are evaluated basic variables such as pressure and velocity. There are also evaluated radial force (Fr and axial force (Fa acting on the rotor for different boundary conditions (different speeds of rotation and precession. Subsequently, the pressure gradients (Δp are evaluated between the radial grooves for different computational domain. Results are compared to variant of narrow gap without radial grooves. Numerical simulation is realized in the program system ANSYS Fluent.