Suspect/Counterfeit Items Information Guide for Subcontractors/Suppliers

Energy Technology Data Exchange (ETDEWEB)

Tessmar, Nancy D. [Los Alamos National Laboratory; Salazar, Michael J. [Los Alamos National Laboratory

2012-09-18

Counterfeiting of industrial and commercial grade items is an international problem that places worker safety, program objectives, expensive equipment, and security at risk. In order to prevent the introduction of Suspect/Counterfeit Items (S/CI), this information sheet is being made available as a guide to assist in the implementation of S/CI awareness and controls, in conjunction with subcontractor's/supplier's quality assurance programs. When it comes to counterfeit goods, including industrial materials, items, and equipment, no market is immune. Some manufactures have been known to misrepresent their products and intentionally use inferior materials and processes to manufacture substandard items, whose properties can significantly cart from established standards and specifications. These substandard items termed by the Department of Energy (DOE) as S/CI, pose immediate and potential threats to the safety of DOE and contractor workers, the public, and the environment. Failure of certain systems and processes caused by an S/CI could also have national security implications at Los Alamos National Laboratory (LANL). Nuclear Safety Rules (federal Laws), DOE Orders, and other regulations set forth requirements for DOE contractors to implement effective controls to assure that items and services meet specified requirements. This includes techniques to implement and thereby minimizing the potential threat of entry of S/CI to LANL. As a qualified supplier of goods or services to the LANL, your company will be required to establish and maintain effective controls to prevent the introduction of S/CI to LANL. This will require that your company warrant that all items (including their subassemblies, components, and parts) sold to LANL are genuine (i.e. not counterfeit), new, and unused, and conform to the requirements of the LANL purchase orders/contracts unless otherwise approved in writing to the Los Alamos National Security (LANS) contract administrator

Can tDCS enhance item-specific effects and generalization after linguistically motivated aphasia therapy for verbs?

NARCIS (Netherlands)

de Aguiar, Vania; Bastiaanse, Roelien; Capasso, Rita; Gandolfi, Marialuisa; Smania, Nicola; Rossi, Giorgio; Miceli, Gabriele

2015-01-01

Background: Aphasia therapy focusing on abstract properties of language promotes both item-specific effects and generalization to untreated materials. Neuromodulation with transcranial Direct Current Stimulation (tDCS) has been shown to enhance item-specific improvement, but its potential to enhance

Development of a questionnaire to assess patient satisfaction with allergen-specific immunotherapy in adults: item generation, item reduction, and preliminary validation

Directory of Open Access Journals (Sweden)

Justícia JL

2011-05-01

Full Text Available Jose Luis Justícia1, Eva Baró2, Victoria Cardona3, Pedro Guardia4, Pedro Ojeda5, José Maria Olaguíbel6, José Maria Vega7, Carmen Vidal81Medical Department, Stallergenes Ibérica, Barcelona, Spain; 2Health Outcomes Research Department, 3D Health Research, Barcelona, Spain; 3Hospital Vall d'Hebron, Barcelona, Spain; 4Hospital Virgen Macarena, Sevilla, Spain; 5Clínica de Asma y Alergia Dres. Ojeda, Madrid, Spain; 6Complejo Hospitalario de Navarra, Pamplona, Spain; 7Hospital Regional Universitario Carlos Haya Málaga, Spain; 8Complejo Hospitalario Universitario de Santiago, Santiago de Compostela, SpainBackground: Allergen-specific immunotherapy (SIT is a treatment capable of modifying the natural course of allergy, so ensuring good adherence to SIT is fundamental. Up until now there has not existed an instrument specifically developed to measure patient satisfaction with SIT, although its assessment could help us to comprehend better and improve treatment adherence and effectiveness. The aim of this study was to develop an instrument to measure adult patient satisfaction with SIT.Methods: Items were generated from a literature review, focus groups with allergic adult patients undergoing SIT, and a meeting with experts. Potential items were administered to allergic patients undergoing SIT in an observational, cross-sectional, multicenter study. Item reduction was based on quantitative and qualitative criteria. A preliminary assessment of feasibility, reliability, and validity of the retained items was performed.Results: An initial pool of 70 items was administered to 257 patients undergoing SIT. Fifty-four items were eliminated resulting in a provisional instrument with 16 items. Factor analysis yielded four factors that were identified as perceived efficacy, activities and environment, cost-benefit balance, and overall satisfaction, explaining 74.8% of variance. Ceiling and floor effects were negligible for overall score. Overall score was

How Does Creating a Concept Map Affect Item-Specific Encoding?

Science.gov (United States)

Grimaldi, Phillip J.; Poston, Laurel; Karpicke, Jeffrey D.

2015-01-01

Concept mapping has become a popular learning tool. However, the processes underlying the task are poorly understood. In the present study, we examined the effect of creating a concept map on the processing of item-specific information. In 2 experiments, subjects learned categorized or ad hoc word lists by making pleasantness ratings, sorting…

Working memory in schizophrenia: behavioral and neural evidence for reduced susceptibility to item-specific proactive interference.

Science.gov (United States)

Kaller, Christoph P; Loosli, Sandra V; Rahm, Benjamin; Gössel, Astrid; Schieting, Stephan; Hornig, Tobias; Hennig, Jürgen; Tebartz van Elst, Ludger; Weiller, Cornelius; Katzev, Michael

2014-09-15

Susceptibility to item-specific proactive interference (PI) contributes to interindividual differences in working memory (WM) capacity and complex cognition relying on WM. Although WM deficits are a well-recognized impairment in schizophrenia, the underlying pathophysiological effects on specific WM control functions, such as the ability to resist item-specific PI, remain unknown. Moreover, opposing hypotheses on increased versus reduced PI susceptibility in schizophrenia are both justifiable by the extant literature. To provide first insights into the behavioral and neural correlates of PI-related WM control in schizophrenia, a functional magnetic resonance imaging experiment was conducted in a sample of 20 patients and 20 well-matched control subjects. Demands on item-specific PI were experimentally manipulated in a recent-probes task (three runs, 64 trials each) requiring subjects to encode and maintain a set of four target items per trial. Compared with healthy control subjects, schizophrenia patients showed a significantly reduced PI susceptibility in both accuracy and latency measures. Notably, reduced PI susceptibility in schizophrenia was not associated with overall WM impairments and thus constituted an independent phenomenon. In addition, PI-related activations in inferior frontal gyrus and anterior insula, typically assumed to support PI resistance, were reduced in schizophrenia, thus ruling out increased neural efforts as a potential cause of the patients' reduced PI susceptibility. The present study provides first evidence for a diminished vulnerability of schizophrenia patients to item-specific PI, which is presumably a consequence of the patients' more efficient clearing of previously relevant WM traces and the accordingly reduced likelihood for item-specific PI to occur. Copyright © 2014 Society of Biological Psychiatry. Published by Elsevier Inc. All rights reserved.

Can Contingency Learning Alone Account for Item-Specific Control? Evidence from within- and Between-Language ISPC Effects

Science.gov (United States)

Atalay, Nart Bedin; Misirlisoy, Mine

2012-01-01

The item-specific proportion congruence (ISPC) manipulation (Jacoby, Lindsay, & Hessels, 2003) produces larger Stroop interference for mostly congruent items than mostly incongruent items. This effect has been attributed to dynamic control over word-reading processes. However, proportion congruence of an item in the ISPC manipulation is…

Plutonium Finishing Plant (PFP) Criticality Alarm System Commercial Grade Item (CGI) Critical Characteristics

International Nuclear Information System (INIS)

WHITE, W.F.

1999-01-01

This document specifies the critical characteristics for Commercial Grade Items (CGI) procured for PFP's criticality alarm system as required by HNF-PRO-268 and HNF-PRO-1819. These are the minimum specifications that the equipment must meet in order to properly perform its safety function. There may be several manufacturers or models that meet the critical characteristics for any one item. PFP's Criticality Alarm System includes the nine criticality alarm system panels and their associated hardware. This includes all parts up to the first breaker in the electrical distribution system. Specific system boundaries and justifications are contained in HNF-SD-CP-SDD-003, ''Definition and Means of Maintaining the Criticality Detectors and Alarms Portion of the PFP Safety Envelope.'' The procurement requirements associated with the system necessitates procurement of some system equipment as Commercial Grade Items in accordance with HNF-PRO-268, ''Control of Purchased Items and Services.''

Reconfigurability of behavioural specifications for manufacturing systems

Science.gov (United States)

Schmidt, Klaus Werner

2017-12-01

Reconfigurable manufacturing systems (RMS) support flexibility in the product variety and the configuration of the manufacturing system itself in order to enable quick adjustments to new products and production requirements. As a consequence, an essential feature of RMS is their ability to rapidly modify the control strategy during run-time. In this paper, the particular problem of changing the specified operation of a RMS, whose logical behaviour is modelled as a finite state automaton, is addressed. The notion of reconfigurability of specifications (RoS) is introduced and it is shown that the stated reconfiguration problem can be formulated as a controlled language convergence problem. In addition, algorithms for the verification of RoS and the construction of a reconfiguration supervisor are proposed. The supervisor is realised in a modular way which facilitates the extension by new configurations. Finally, it is shown that a supremal nonblocking and controllable strict subautomaton of the plant automaton that fulfils RoS exists in case RoS is violated for the plant automaton itself and an algorithm for the computation of this strict subautomaton is presented. The developed concepts and results are illustrated by a manufacturing cell example.

In Situ Manufacturing is a Necessary Part of Any Planetary Architecture

Science.gov (United States)

Edmunson, Jennifer E.; McLemore, Carole A.

2012-01-01

The key to any sustainable presence in space is the ability to manufacture necessary tools, parts, structures, spares, etc. in situ and on demand. Cost, volume, and up-mass constraints prohibit launching everything needed for long-duration or long-distance missions from Earth, including spare parts and replacement systems. There are many benefits to building items as-needed in situ using computer aided drafting (CAD) models and additive manufacturing technology: (1) Cost, up-mass, and volume savings for launch due to the ability to manufacture specific parts when needed. (2) CAD models can be generated on Earth and transmitted to the station or spacecraft, or they can be designed in situ for any task. Thus, multiple people in many locations can work on a single problem. (3) Items can be produced that will enhance the safety of crew and vehicles (e.g., latches or guards). (4) Items can be produced on-demand in a small amount of time (i.e., hours or days) compared to traditional manufacturing methods and, therefore, would not require the lengthy amount of time needed to machine the part from a solid block of material nor the wait time required if the part had to be launched from Earth. (5) Used and obsolete parts can be recycled into powder or wire feedstock for use in later manufacturing. (6) Ultimately, the ability to produce items as-needed will reduce mission risk, as one will have everything they need to fix a broken system or fashion a new part making it available on a more timely basis.

Just-in-time Design and Additive Manufacture of Patient-specific Medical Implants

Science.gov (United States)

Shidid, Darpan; Leary, Martin; Choong, Peter; Brandt, Milan

Recent advances in medical imaging and manufacturing science have enabled the design and production of complex, patient-specific orthopaedic implants. Additive Manufacture (AM) generates three-dimensional structures layer by layer, and is not subject to the constraints associated with traditional manufacturing methods. AM provides significant opportunities for the design of novel geometries and complex lattice structures with enhanced functional performance. However, the design and manufacture of patient-specific AM implant structures requires unique expertise in handling various optimization platforms. Furthermore, the design process for complex structures is computationally intensive. The primary aim of this research is to enable the just-in-time customisation of AM prosthesis; whereby AM implant design and manufacture be completed within the time constraints of a single surgical procedure, while minimising prosthesis mass and optimising the lattice structure to match the stiffness of the surrounding bone tissue. In this research, a design approach using raw CT scan data is applied to the AM manufacture of femoral prosthesis. Using the proposed just-in-time concept, the mass of the prosthesis was rapidly designed and manufactured while satisfying the associated structural requirements. Compressive testing of lattice structures manufactured using proposed method shows that the load carrying capacity of the resected composite bone can be recovered by up to 85% and the compressive stiffness of the AM prosthesis is statistically indistinguishable from the stiffness of the initial bone.

Design - manufacturing and characterization of specific ultrasonic probes

International Nuclear Information System (INIS)

Petit, J.

1985-01-01

Optimization of ultrasonic examinations requires essentially to determine precisely parameters used for manufacturing of probes and to check characteristics of beams used. The system presented permits an automatic determination of dimensions of beams in conditions which are totally representative of those of their use. In the field of ultrasonic examinations a good estimate or knowledge of sound beams is of great help to solve difficult examination problems. The FRAMATOME's Centre d'Etude et de Recherche en Essais Non Destructifs (CEREND) : (Study and Research Center in Non-Destructive Testing) has developed and elaborated various techniques in order to improve ultrasonic examinations with specific probes. These techniques concern design, manufacturing and characterization of these probes

16 CFR 304.6 - Marking requirements for imitation numismatic items.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Marking requirements for imitation... for imitation numismatic items. (a) An imitation numismatic item which is manufactured in the United... the item. (3) An imitation numismatic item of incusable material shall be incused with the word “COPY...

Specifications, quality control, manufacturing, and testing of accelerator magnets

CERN Document Server

Einfeld, D

2010-01-01

The performance of the magnets plays an important role in the functioning of an accelerator. Most of the magnets are designed at the accelerator laboratory and built by industry. The link between the laboratory and the manufacturer is the contract containing the Technical Specifications of the magnets. For an overview of the contents of the Technical Specifications, the specifications for the magnets of ALBA (bending, quadrupole, and sextupole) are described in this paper. The basic rules of magnet design are reviewed in Appendix A.

Memory deficit in patients with schizophrenia and posttraumatic stress disorder: relational vs item-specific memory

Directory of Open Access Journals (Sweden)

Jung W

2016-05-01

Full Text Available Wookyoung Jung,1 Seung-Hwan Lee1,2 1Clinical Emotions and Cognition Research Laboratory, Department of Psychiatry, Inje University, Ilsan-Paik Hospital, 2Department of Psychiatry, Inje University, Ilsan-Paik Hospital, Goyang, Korea Abstract: It has been well established that patients with schizophrenia have impairments in cognitive functioning and also that patients who experienced traumatic events suffer from cognitive deficits. Of the cognitive deficits revealed in schizophrenia or posttraumatic stress disorder (PTSD patients, the current article provides a brief review of deficit in episodic memory, which is highly predictive of patients’ quality of life and global functioning. In particular, we have focused on studies that compared relational and item-specific memory performance in schizophrenia and PTSD, because measures of relational and item-specific memory are considered the most promising constructs for immediate tangible development of clinical trial paradigm. The behavioral findings of schizophrenia are based on the tasks developed by the Cognitive Neuroscience Treatment Research to Improve Cognition in Schizophrenia (CNTRICS initiative and the Cognitive Neuroscience Test Reliability and Clinical Applications for Schizophrenia (CNTRACS Consortium. The findings we reviewed consistently showed that schizophrenia and PTSD are closely associated with more severe impairments in relational memory compared to item-specific memory. Candidate brain regions involved in relational memory impairment in schizophrenia and PTSD are also discussed. Keywords: schizophrenia, posttraumatic stress disorder, episodic memory deficit, relational memory, item-specific memory, prefrontal cortex, hippocampus

Item-specific proactive interference in olfactory working memory.

Science.gov (United States)

Moss, Andrew; Miles, Christopher; Elsley, Jane; Johnson, Andrew

2018-04-01

We examine item-specific olfactory proactive interference (PI) effects and undertake comparisons with verbal and non-verbal visual stimuli. Using a sequential recent-probes task, we show no evidence for PI with hard-to-name odours (Experiment 1). However, verbalisable odours do exhibit PI effects (Experiment 2). These findings occur despite above chance performance and similar serial position functions across both tasks. Experiments 3 and 4 apply words and faces, respectively, to our modified procedure, and show that methodological differences cannot explain the null finding in Experiment 1. The extent to which odours exhibit analogous PI effects to that of other modalities is, we argue, contingent on the characteristics of the odours employed.

Managing suspect and counterfeit items in the nuclear industry

International Nuclear Information System (INIS)

2000-08-01

Some manufacturers and suppliers use inferior materials and processes to make substandard supplies whose properties can vary significantly from established standards and specifications. Other suppliers distribute items that they know do not meet the purchase requirements or provide documentation that misrepresent actual conformance to established specifications and standards. These substandard supplies, or suspect/counterfeit items (S/CIs), pose potential threats to the safety of workers, the public and the environment and may also have a detrimental effect on security and operations at nuclear facilities. Nuclear facilities often procure and use commercial-grade items and the quality assurance policies/procedures and procurement methods are not always properly applied to avoid the entry of S/Cls into those facilities. This publication offers practical guidance on how to apply existing quality assurance programmes to effectively prevent the procurement and use of S/Cls. In particular, it provides a practical method of applying the requirements and guidance contained in the IAEA Safety Series 50-C/SG-Q: Code and Safety Guides on Quality Assurance for Safety in Nuclear Power Plants and other Nuclear Installations (1996), to the S/CIs issue

16 CFR 304.5 - Marking requirements for imitation political items.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Marking requirements for imitation political... imitation political items. (a) An imitation political item which is manufactured in the United States, or...) An imitation political item of incusable material shall be incused with the calendar year in sans...

Evolution of a Test Item

Science.gov (United States)

Spaan, Mary

2007-01-01

This article follows the development of test items (see "Language Assessment Quarterly", Volume 3 Issue 1, pp. 71-79 for the article "Test and Item Specifications Development"), beginning with a review of test and item specifications, then proceeding to writing and editing of items, pretesting and analysis, and finally selection of an item for a…

Psychometric properties of the Chinese version of resilience scale specific to cancer: an item response theory analysis.

Science.gov (United States)

Ye, Zeng Jie; Liang, Mu Zi; Zhang, Hao Wei; Li, Peng Fei; Ouyang, Xue Ren; Yu, Yuan Liang; Liu, Mei Ling; Qiu, Hong Zhong

2018-06-01

Classic theory test has been used to develop and validate the 25-item Resilience Scale Specific to Cancer (RS-SC) in Chinese patients with cancer. This study was designed to provide additional information about the discriminative value of the individual items tested with an item response theory analysis. A two-parameter graded response model was performed to examine whether any of the items of the RS-SC exhibited problems with the ordering and steps of thresholds, as well as the ability of items to discriminate patients with different resilience levels using item characteristic curves. A sample of 214 Chinese patients with cancer diagnosis was analyzed. The established three-dimension structure of the RS-SC was confirmed. Several items showed problematic thresholds or discrimination ability and require further revision. Some problematic items should be refined and a short-form of RS-SC maybe feasible in clinical settings in order to reduce burden on patients. However, the generalizability of these findings warrants further investigations.

Patient specific root-analogue dental implants – additive manufacturing and finite element analysis

Directory of Open Access Journals (Sweden)

Gattinger Johannes

2016-09-01

Full Text Available Aim of this study was to prove the possibility of manufacturing patient specific root analogue two-part (implant and abutment implants by direct metal laser sintering. The two-part implant design enables covered healing of the implant. Therefore, CT-scans of three patients are used for reverse engineering of the implants, abutments and crowns. Patient specific implants are manufactured and measured concerning dimensional accuracy and surface roughness. Impacts of occlusal forces are simulated via FEA and compared to those of standard implants.

Development and fabrication of patient-specific knee implant using additive manufacturing techniques

Science.gov (United States)

Zammit, Robert; Rochman, Arif

2017-10-01

Total knee replacement is the most effective treatment to relief pain and restore normal function in a diseased knee joint. The aim of this research was to develop a patient-specific knee implant which can be fabricated using additive manufacturing techniques and has reduced wear rates using a highly wear resistant materials. The proposed design was chosen based on implant requirements, such as reduction in wear rates as well as strong fixation. The patient-specific knee implant improves on conventional knee implants by modifying the articulating surfaces and bone-implant interfaces. Moreover, tribological tests of different polymeric wear couples were carried out to determine the optimal materials to use for the articulating surfaces. Finite element analysis was utilized to evaluate the stresses sustained by the proposed design. Finally, the patient-specific knee implant was successfully built using additive manufacturing techniques.

Design and manufacturing of patient-specific orthodontic appliances by computer-aided engineering techniques.

Science.gov (United States)

Barone, Sandro; Neri, Paolo; Paoli, Alessandro; Razionale, Armando Viviano

2018-01-01

Orthodontic treatments are usually performed using fixed brackets or removable oral appliances, which are traditionally made from alginate impressions and wax registrations. Among removable devices, eruption guidance appliances are used for early orthodontic treatments in order to intercept and prevent malocclusion problems. Commercially available eruption guidance appliances, however, are symmetric devices produced using a few standard sizes. For this reason, they are not able to meet all the specific patient's needs since the actual dental anatomies present various geometries and asymmetric conditions. In this article, a computer-aided design-based methodology for the design and manufacturing of a patient-specific eruption guidance appliances is presented. The proposed approach is based on the digitalization of several steps of the overall process: from the digital reconstruction of patients' anatomies to the manufacturing of customized appliances. A finite element model has been developed to evaluate the temporomandibular joint disks stress level caused by using symmetric eruption guidance appliances with different teeth misalignment conditions. The developed model can then be used to guide the design of a patient-specific appliance with the aim at reducing the patient discomfort. At this purpose, two different customization levels are proposed in order to face both arches and single tooth misalignment issues. A low-cost manufacturing process, based on an additive manufacturing technique, is finally presented and discussed.

The Effects of Goal Relevance and Perceptual Features on Emotional Items and Associative Memory.

Science.gov (United States)

Mao, Wei B; An, Shu; Yang, Xiao F

2017-01-01

Showing an emotional item in a neutral background scene often leads to enhanced memory for the emotional item and impaired associative memory for background details. Meanwhile, both top-down goal relevance and bottom-up perceptual features played important roles in memory binding. We conducted two experiments and aimed to further examine the effects of goal relevance and perceptual features on emotional items and associative memory. By manipulating goal relevance (asking participants to categorize only each item image as living or non-living or to categorize each whole composite picture consisted of item image and background scene as natural scene or manufactured scene) and perceptual features (controlling visual contrast and visual familiarity) in two experiments, we found that both high goal relevance and salient perceptual features (high salience of items vs. high familiarity of items) could promote emotional item memory, but they had different effects on associative memory for emotional items and neutral backgrounds. Specifically, high goal relevance and high perceptual-salience of items could jointly impair the associative memory for emotional items and neutral backgrounds, while the effect of item familiarity on associative memory for emotional items would be modulated by goal relevance. High familiarity of items could increase associative memory for negative items and neutral backgrounds only in the low goal relevance condition. These findings suggest the effect of emotion on associative memory is not only related to attentional capture elicited by emotion, but also can be affected by goal relevance and perceptual features of stimulus.

Amnesiacs might get the gist: reduced false recognition in amnesia may be the result of impaired item-specific memory.

Science.gov (United States)

Nissan, Jack; Abrahams, Sharon; Sala, Sergio Della

2013-01-01

It is a common finding in tests of false recognition that amnesic patients recognize fewer related lures than healthy controls, and this has led to assumptions that gist memory is damaged in these patients (Schacter, Verfaellie, & Anes, 1997, Neuropsychology, 11; Schacter, Verfaellie, Anes, & Racine, 1998, Journal of Cognitive Neuroscience, 10; Schacter, Verfaellie, & Pradere, 1996, Journal of Memory and Language, 35). However, clinical observations find that amnesic patients typically hold meaningful conversations and make relevant remarks, and there is some experimental evidence highlighting preserved immediate recall of prose (Baddeley & Wilson, 2002, Neuropsychologia, 40; Gooding, Isaac, & Mayes, 2005, Neuropsychologia, 43; Rosenbaum, Gilboa, Levine, Winocur, & Moscovitch, 2009, Neuropsychologia, 47), which suggests that amnesiacs can get the gist. The present experiment used false recognition paradigms to assess whether the reduced rate of false recognition found in amnesic patients may be a consequence of their impaired item-specific memory. It examined the effect of increasing the item-specific memory of amnesic patient DA by bringing her to criterion on relevant study-lists and compared her performance on a false recognition paradigm with a group of 32 healthy young adults. Results indicated that when DA's item-specific memory was increased she was more able to gist and her performance was no different to the healthy young adults. Previous assumptions that gist memory is necessarily damaged in amnesia might therefore be revisited, since the reduced rate of false recognition could be caused by impaired item-specific memory. The experiment also highlights a positive relationship between item-specific and gist memory which has not previously been accounted for in false-recognition experiments.

32 CFR 507.17 - Procurement and wear of heraldic items.

Science.gov (United States)

2010-07-01

... controlled heraldic items, when authorized by local procurement procedures, may forward a sample insignia to... 32 National Defense 3 2010-07-01 2010-07-01 true Procurement and wear of heraldic items. 507.17... AUTHORITIES AND PUBLIC RELATIONS MANUFACTURE AND SALE OF DECORATIONS, MEDALS, BADGES, INSIGNIA, COMMERCIAL USE...

Verification of the light intensity from halogens curing lamps in comparison with the manufacturer's specifications

International Nuclear Information System (INIS)

Morales Ramirez, Elvis

2011-01-01

The light intensity emitted from halogens curing lamps is measured to determine if photoactivation units utilized in the Caja Costarricense de Seguro Social are complied with the manufacturer's specifications of the lamp and the resin. The light intensity mW/cm 2 from halogens curing lamps operated by odontologist of the Caja Costarricense de Seguro Social is compared with the manufacturer's specifications of the lamp. The light intensity is compared with the manufacturer's specifications of the resin. The results obtained are analyzed to specify that lamp or lamps have presented light intensities lower to indication of the manufacturer. A list of recommendations is performed for each Servicio de Odontologia of the Caja Costarricense de Seguro Social of the Region Central Sur of the results reported [es

Identifying Country-Specific Cultures of Physics Education: A differential item functioning approach

Science.gov (United States)

Mesic, Vanes

2012-11-01

In international large-scale assessments of educational outcomes, student achievement is often represented by unidimensional constructs. This approach allows for drawing general conclusions about country rankings with respect to the given achievement measure, but it typically does not provide specific diagnostic information which is necessary for systematic comparisons and improvements of educational systems. Useful information could be obtained by exploring the differences in national profiles of student achievement between low-achieving and high-achieving countries. In this study, we aimed to identify the relative weaknesses and strengths of eighth graders' physics achievement in Bosnia and Herzegovina in comparison to the achievement of their peers from Slovenia. For this purpose, we ran a secondary analysis of Trends in International Mathematics and Science Study (TIMSS) 2007 data. The student sample consisted of 4,220 students from Bosnia and Herzegovina and 4,043 students from Slovenia. After analysing the cognitive demands of TIMSS 2007 physics items, the correspondent differential item functioning (DIF)/differential group functioning contrasts were estimated. Approximately 40% of items exhibited large DIF contrasts, indicating significant differences between cultures of physics education in Bosnia and Herzegovina and Slovenia. The relative strength of students from Bosnia and Herzegovina showed to be mainly associated with the topic area 'Electricity and magnetism'. Classes of items which required the knowledge of experimental method, counterintuitive thinking, proportional reasoning and/or the use of complex knowledge structures proved to be differentially easier for students from Slovenia. In the light of the presented results, the common practice of ranking countries with respect to universally established cognitive categories seems to be potentially misleading.

The Effects of Goal Relevance and Perceptual Features on Emotional Items and Associative Memory

Directory of Open Access Journals (Sweden)

Wei B. Mao

2017-07-01

Full Text Available Showing an emotional item in a neutral background scene often leads to enhanced memory for the emotional item and impaired associative memory for background details. Meanwhile, both top–down goal relevance and bottom–up perceptual features played important roles in memory binding. We conducted two experiments and aimed to further examine the effects of goal relevance and perceptual features on emotional items and associative memory. By manipulating goal relevance (asking participants to categorize only each item image as living or non-living or to categorize each whole composite picture consisted of item image and background scene as natural scene or manufactured scene and perceptual features (controlling visual contrast and visual familiarity in two experiments, we found that both high goal relevance and salient perceptual features (high salience of items vs. high familiarity of items could promote emotional item memory, but they had different effects on associative memory for emotional items and neutral backgrounds. Specifically, high goal relevance and high perceptual-salience of items could jointly impair the associative memory for emotional items and neutral backgrounds, while the effect of item familiarity on associative memory for emotional items would be modulated by goal relevance. High familiarity of items could increase associative memory for negative items and neutral backgrounds only in the low goal relevance condition. These findings suggest the effect of emotion on associative memory is not only related to attentional capture elicited by emotion, but also can be affected by goal relevance and perceptual features of stimulus.

Assessing the specificity of posttraumatic stress disorder's dysphoric items within the dysphoria model.

Science.gov (United States)

Armour, Cherie; Shevlin, Mark

2013-10-01

The factor structure of posttraumatic stress disorder (PTSD) currently used by the Diagnostic and Statistical Manual of Mental Disorders, Fourth Edition (DSM-IV), has received limited support. A four-factor dysphoria model is widely supported. However, the dysphoria factor of this model has been hailed as a nonspecific factor of PTSD. The present study investigated the specificity of the dysphoria factor within the dysphoria model by conducting a confirmatory factor analysis while statistically controlling for the variance attributable to depression. The sample consisted of 429 individuals who met the diagnostic criteria for PTSD in the National Comorbidity Survey. The results concluded that there was no significant attenuation in any of the PTSD items. This finding is pertinent given several proposals for the removal of dysphoric items from the diagnostic criteria set of PTSD in the upcoming DSM-5.

Instructional Topics in Educational Measurement (ITEMS) Module: Using Automated Processes to Generate Test Items

Science.gov (United States)

Gierl, Mark J.; Lai, Hollis

2013-01-01

Changes to the design and development of our educational assessments are resulting in the unprecedented demand for a large and continuous supply of content-specific test items. One way to address this growing demand is with automatic item generation (AIG). AIG is the process of using item models to generate test items with the aid of computer…

26 CFR 1.460-2 - Long-term manufacturing contracts.

Science.gov (United States)

2010-04-01

... time normally required to design and manufacture the first unit of an item for which the taxpayer... manufacture a new type of industrial equipment. C reasonably expects the normal production period for this... 26 Internal Revenue 6 2010-04-01 2010-04-01 false Long-term manufacturing contracts. 1.460-2...

Printed Proliferation: The Implications of Additive Manufacturing and Nuclear Weapons Proliferation

Energy Technology Data Exchange (ETDEWEB)

Lindsey, Nicholas C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-01-26

The growth of additive manufacturing as a disruptive technology poses nuclear proliferation concerns worthy of serious consideration. Additive manufacturing began in the early 1980s with technological advances in polymer manipulation, computer capabilities, and computer-aided design (CAD) modeling. It was originally limited to rapid prototyping; however, it eventually developed into a complete means of production that has slowly penetrated the consumer market. Today, additive manufacturing machines can produce complex and unique items in a vast array of materials including plastics, metals, and ceramics. These capabilities have democratized the manufacturing industry, allowing almost anyone to produce items as simple as cup holders or as complex as jet fuel nozzles. Additive manufacturing, or three-dimensional (3D) printing as it is commonly called, relies on CAD files created or shared by individuals with additive manufacturing machines to produce a 3D object from a digital model. This sharing of files means that a 3D object can be scanned or rendered as a CAD model in one country, and then downloaded and printed in another country, allowing items to be shared globally without physically crossing borders. The sharing of CAD files online has been a challenging task for the export controls regime to manage over the years, and additive manufacturing could make these transfers more common. In this sense, additive manufacturing is a disruptive technology not only within the manufacturing industry but also within the nuclear nonproliferation world. This paper provides an overview of additive manufacturing concerns of proliferation.

Electron Beam Melting Manufacturing Technology for Individually Manufactured Jaw Prosthesis: A Case Report.

Science.gov (United States)

Suska, Felicia; Kjeller, Göran; Tarnow, Peter; Hryha, Eduard; Nyborg, Lars; Snis, Anders; Palmquist, Anders

2016-08-01

In the field of maxillofacial reconstruction, additive manufacturing technologies, specifically electron beam melting (EBM), offer clinicians the potential for patient-customized design of jaw prostheses, which match both load-bearing and esthetic demands. The technique allows an innovative, functional design, combining integrated porous regions for bone ingrowth and secondary biological fixation with solid load-bearing regions ensuring the biomechanical performance. A patient-specific mandibular prosthesis manufactured using EBM was successfully used to reconstruct a patient's mandibular defect after en bloc resection. Over a 9-month follow-up period, the patient had no complications. A short operating time, good esthetic outcome, and high level of patient satisfaction as measured by quality-of-life questionnaires-the European Organisation for Research and Treatment of Cancer QLQ-C30 (30-item quality-of-life core questionnaire) and H&N35 (head and neck cancer module)-were reported for this case. Individually planned and designed EBM-produced prostheses may be suggested as a possible future alternative to fibular grafts or other reconstructive methods. However, the role of porosity, the role of geometry, and the optimal combination of solid and porous parts, as well as surface properties in relation to soft tissues, should be carefully evaluated in long-term clinical trials. Copyright © 2016 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

A Case Study on an Item Writing Process: Use of Test Specifications, Nature of Group Dynamics, and Individual Item Writers' Characteristics

Science.gov (United States)

Kim, Jiyoung; Chi, Youngshin; Huensch, Amanda; Jun, Heesung; Li, Hongli; Roullion, Vanessa

2010-01-01

This article discusses a case study on an item writing process that reflects on our practical experience in an item development project. The purpose of the article is to share our lessons from the experience aiming to demystify item writing process. The study investigated three issues that naturally emerged during the project: how item writers use…

Virtual Manufacturing Techniques Designed and Applied to Manufacturing Activities in the Manufacturing Integration and Technology Branch

Science.gov (United States)

Shearrow, Charles A.

1999-01-01

One of the identified goals of EM3 is to implement virtual manufacturing by the time the year 2000 has ended. To realize this goal of a true virtual manufacturing enterprise the initial development of a machinability database and the infrastructure must be completed. This will consist of the containment of the existing EM-NET problems and developing machine, tooling, and common materials databases. To integrate the virtual manufacturing enterprise with normal day to day operations the development of a parallel virtual manufacturing machinability database, virtual manufacturing database, virtual manufacturing paradigm, implementation/integration procedure, and testable verification models must be constructed. Common and virtual machinability databases will include the four distinct areas of machine tools, available tooling, common machine tool loads, and a materials database. The machine tools database will include the machine envelope, special machine attachments, tooling capacity, location within NASA-JSC or with a contractor, and availability/scheduling. The tooling database will include available standard tooling, custom in-house tooling, tool properties, and availability. The common materials database will include materials thickness ranges, strengths, types, and their availability. The virtual manufacturing databases will consist of virtual machines and virtual tooling directly related to the common and machinability databases. The items to be completed are the design and construction of the machinability databases, virtual manufacturing paradigm for NASA-JSC, implementation timeline, VNC model of one bridge mill and troubleshoot existing software and hardware problems with EN4NET. The final step of this virtual manufacturing project will be to integrate other production sites into the databases bringing JSC's EM3 into a position of becoming a clearing house for NASA's digital manufacturing needs creating a true virtual manufacturing enterprise.

Sensitivity and specificity of the 3-item memory test in the assessment of post traumatic amnesia.

Science.gov (United States)

Andriessen, Teuntje M J C; de Jong, Ben; Jacobs, Bram; van der Werf, Sieberen P; Vos, Pieter E

2009-04-01

To investigate how the type of stimulus (pictures or words) and the method of reproduction (free recall or recognition after a short or a long delay) affect the sensitivity and specificity of a 3-item memory test in the assessment of post traumatic amnesia (PTA). Daily testing was performed in 64 consecutively admitted traumatic brain injured patients, 22 orthopedically injured patients and 26 healthy controls until criteria for resolution of PTA were reached. Subjects were randomly assigned to a test with visual or verbal stimuli. Short delay reproduction was tested after an interval of 3-5 minutes, long delay reproduction was tested after 24 hours. Sensitivity and specificity were calculated over the first 4 test days. The 3-word test showed higher sensitivity than the 3-picture test, while specificity of the two tests was equally high. Free recall was a more effortful task than recognition for both patients and controls. In patients, a longer delay between registration and recall resulted in a significant decrease in the number of items reproduced. Presence of PTA is best assessed with a memory test that incorporates the free recall of words after a long delay.

Material selection for design, manufacturing and application

International Nuclear Information System (INIS)

Zaid, A.I.O.

2011-01-01

Developing a new engineering material product or changing an existing one requires new design selecting material and choosing appropriate and economical manufacturing processes. These three main factors play a great role on the performance of the product in service. These items are independent and should not be performed in isolation from each other. With the great advancement of technology in the last decade and with the greater number of engineering materials which are now available, together with the increasing pressure to produce more economic and get reliable products an integrated approach which considers design, material selection and the appropriate manufacturing process makes it easier to achieve the optimum product that combines the functional requirements with the reliability at competitive cost. These diverse activities or items are interdependent; therefore should not be considered in isolation from each other, for example, it is not sufficient that design of the product should satisfy the technical, safety and legal requirements, it must also be possible to be manufactured economically and to be sold at a competitive price and easily disposed at the end of its working life cycle. In this paper, the interaction of these items together in order to arrive to the optimum solution for a particular application are given and discussed. (author)

Cost estimation of a specifically designed direct light processing (DLP) additive manufacturing machine for precision printing

DEFF Research Database (Denmark)

Charalambis, Alessandro; Davoudinejad, Ali; Tosello, Guido

2017-01-01

creating new opportunities for manufacturers in a variety of industrial sectors. AM is an essentialprototyping technique for product design and development that is used in many different fields. However, the suitability of AMapplications in actual production in an industrial context needs to be determined......Additive Manufacturing (AM) refers to a portfolio of novel manufacturing technologies based on a layer-by-layer fabrication method.The market and industrial application of additive manufacturing technologies as an established manufacturing process have increasedexponentially in the last years....... This study, presents a cost estimation model forprecision printing with a specifically designed Digital Light Processing (DLP) AM machine built and validated at the Technical Universityof Denmark. The model presented in this study can be easily adapted and applied to estimate within a high level...

Adaptive memory: the survival scenario enhances item-specific processing relative to a moving scenario.

Science.gov (United States)

Burns, Daniel J; Hart, Joshua; Griffith, Samantha E; Burns, Amy D

2013-01-01

Nairne, Thompson, and Pandeirada (2007) found that retention of words rated for their relevance to survival is superior to that of words encoded under numerous other deep processing conditions. They suggested that our memory systems might have evolved to confer an advantage for survival-relevant information. Burns, Burns, and Hwang (2011) suggested a two-process explanation of the proximate mechanisms responsible for the survival advantage. Whereas most control tasks encourage only one type of processing, the survival task encourages both item-specific and relational processing. They found that when control tasks encouraged both types of processing, the survival processing advantage was eliminated. However, none of their control conditions included non-survival scenarios (e.g., moving, vacation, etc.), so it is not clear how this two-process explanation would explain the survival advantage when scenarios are used as control conditions. The present experiments replicated the finding that the survival scenario improves recall relative to a moving scenario in both a between-lists and within-list design and also provided evidence that this difference was accompanied by an item-specific processing difference, not a difference in relational processing. The implications of these results for several existing accounts of the survival processing effect are discussed.

Sensitivity and specificity of the 3-item memory test in the assessment of post traumatic amnesia.

NARCIS (Netherlands)

Andriessen, T.M.J.C.; Jong, B. de; Jacobs, B.; Werf, S.P. van der; Vos, P.E.

2009-01-01

PRIMARY OBJECTIVE: To investigate how the type of stimulus (pictures or words) and the method of reproduction (free recall or recognition after a short or a long delay) affect the sensitivity and specificity of a 3-item memory test in the assessment of post traumatic amnesia (PTA). METHODS: Daily

Technical specification for IR rig manufacture

Energy Technology Data Exchange (ETDEWEB)

Han Hyon Soo; Cho, W. K.; Kim, S. D.; Park, U. J.; Hong, S. B.; Yoo, K. M

2000-10-01

IR Rig is one of the equipments are required in HANARO core for a radioisotope target. The various conditions like high radiation, high heat, rapid flow and vibration may cause swelling, Brittleness and acceleration of corrosion in HANARO core. These specific problems can be prevented and the safety of such equipment are prerequisite as well as durableness and surveillance. Therefore, the selection of material has to be made on the basis of small cross-section area, low energy emission by the gamma ray due to the absorption of neutron and short half life. The body is consist of aluminum and Inconel-750 was used for the internal spring(coil) which is known to be durable. The whole production process including the purchase of accessory, mechanical processing, welding and assembly was carried out according to the standard procedure to meet the requirement. A design, manufacture, utilization of reactor core and the other relevant uses were fit to class ''T'' to certify the whole process as general. And design, fabrication, analytical test, materials and accessory were carried out based on the ASME, ASTM, ANSI, AWS, JIS and KS standard.

Life sciences payload definition and integration study. Volume 3: Preliminary equipment item specification catalog for the carry-on laboratories. [for Spacelab

Science.gov (United States)

1974-01-01

All general purpose equipment items contained in the final carry-on laboratory (COL) design concepts are described in terms of specific requirements identified for COL use, hardware status, and technical parameters such as weight, volume, power, range, and precision. Estimated costs for each item are given, along with projected development times.

JET Project: technical developments, status of the manufacturing work in industry, administrative and managerial aspects

International Nuclear Information System (INIS)

Bertolini, E.

1977-01-01

The Joint European Torus (JET) is the largest experimental device foreseen in the five year fusion plan (1976 to 1980) of the European Economic Community (EEC) and it represents about 20% of the total cost of the programme. The basic machine design, the individual items and the overall cost estimates were completed by June 1975, while the detailed design was finished during 1976, together with the preparation of purchase specifications for major machine components. Tenders covering more than 50% of the total JET cost (all within the estimates) have been obtained and the first stages of manufacturing contracts for up to 30% of the JET hardware budget have already been placed (namely manufacture of the Toroidal Field Coil Copper, the Toroidal Magnet, the Vacuum Vessel Bellows and the Vacuum Vessel Rigid Sectors), by using up the money available for long delivery items during the Design Phase. The extensive quarrels about the siting and the management structure for the JET Construction Phase, have prevented the JET Team placing more manufacturing orders, due to the lack of a ''go-ahead'' decision and the consequent shortage of staff and allocated money

49 CFR 577.5 - Notification pursuant to a manufacturer's decision.

Science.gov (United States)

2010-10-01

... vehicles or replacement equipment determines that any motor vehicle or item of replacement equipment... manufacturer; identified replacement equipment, in the case of notification sent by a replacement equipment... case of notification sent by a motor vehicle manufacturer; identified replacement equipment, in the...

Organization of project works in Industry 4.0 digital item designing companies

Science.gov (United States)

Gurjanov, A. V.; Zakoldaev, D. A.; Shukalov, A. V.; Zharinov, I. O.

2018-05-01

The task of the project works organization in the Industry 4.0 item designing digital factories is being studied. There is a scheme of the item designing component life cycle. There is also a scheme how to develop and confirm the quality of the item designing component documentation using the mathematical modelling. There is a description of the self-organization principles for the cyber and physical technological equipment in the Industry 4.0 «smart factory» company during the manufacturing process.

Micro-manufacturing: design and manufacturing of micro-products

National Research Council Canada - National Science Library

Koç, Muammer; Özel, Tuğrul

2011-01-01

.... After addressing the fundamentals and non-metallic-based micro-manufacturing processes in the semiconductor industry, it goes on to address specific metallic-based micro-manufacturing processes...

19 CFR 191.8 - Specific manufacturing drawback ruling.

Science.gov (United States)

2010-04-01

...; (3) Description of the type of business in which engaged; (4) Description of the manufacturing or... that is to be exported or destroyed; (5) In the case of a business entity, the names of persons listed... drawback ruling of the manufacturer or producer; (B) The succession of a sole proprietorship, partnership...

Can contingency learning alone account for item-specific control? Evidence from within- and between-language ISPC effects.

Science.gov (United States)

Atalay, Nart Bedin; Misirlisoy, Mine

2012-11-01

The item-specific proportion congruence (ISPC) manipulation (Jacoby, Lindsay, & Hessels, 2003) produces larger Stroop interference for mostly congruent items than mostly incongruent items. This effect has been attributed to dynamic control over word-reading processes. However, proportion congruence of an item in the ISPC manipulation is completely confounded with response contingency, suggesting the alternative hypothesis, that the ISPC effect is a result of learning response contingencies (Schmidt & Besner, 2008). The current study asks whether the ISPC effect can be explained by a pure stimulus-response contingency-learning account, or whether other control processes play a role as well, by comparing within- and between-language conditions in a bilingual task. Experiment 1 showed that contingency learning for noncolor words was larger for the within-language than the between-language condition. Experiment 2 revealed significant ISPC effects for both within- and between-language conditions; importantly, the effect was larger in the former. The results of the contingency analyses for Experiment 2 were parallel to that of Experiment 1 and did not show an interaction between contingency and congruency. Put together, these sets of results support the view that contingency-learning processes dominate color-word ISPC effects.

Life sciences payload definition and integration study, task C and D. Volume 4: Preliminary equipment item specification catalog

Science.gov (United States)

1973-01-01

A specification catalog to define the equipment to be used for conducting life sciences experiments in a space laboratory is presented. The specification sheets list the purpose of the equipment item, and any specific technical requirements which can be identified. The status of similar hardware for ground use is stated with comments regarding modifications required to achieve spaceflight qualified hardware. Pertinent sketches, commercial catalog sheets, or drawings of the applicable equipment are included.

Dissociating the neural correlates of intra-item and inter-item working-memory binding.

Directory of Open Access Journals (Sweden)

Carinne Piekema

Full Text Available BACKGROUND: Integration of information streams into a unitary representation is an important task of our cognitive system. Within working memory, the medial temporal lobe (MTL has been conceptually linked to the maintenance of bound representations. In a previous fMRI study, we have shown that the MTL is indeed more active during working-memory maintenance of spatial associations as compared to non-spatial associations or single items. There are two explanations for this result, the mere presence of the spatial component activates the MTL, or the MTL is recruited to bind associations between neurally non-overlapping representations. METHODOLOGY/PRINCIPAL FINDINGS: The current fMRI study investigates this issue further by directly comparing intrinsic intra-item binding (object/colour, extrinsic intra-item binding (object/location, and inter-item binding (object/object. The three binding conditions resulted in differential activation of brain regions. Specifically, we show that the MTL is important for establishing extrinsic intra-item associations and inter-item associations, in line with the notion that binding of information processed in different brain regions depends on the MTL. CONCLUSIONS/SIGNIFICANCE: Our findings indicate that different forms of working-memory binding rely on specific neural structures. In addition, these results extend previous reports indicating that the MTL is implicated in working-memory maintenance, challenging the classic distinction between short-term and long-term memory systems.

Guidelines on preparation of documentation required in PET radiopharmaceutical manufacturing

International Nuclear Information System (INIS)

2001-01-01

This article made by the Nuclear Pharmacy Working Group, subcommittee on Medical Application of Cyclotron-Produced Radionuclides, Medical Science and Pharmaceutical Committee, Japan Radioisotope Association, described the actual examples of Standards, Standard Operating Procedure, Documents and so on for the purpose of operation along the Standards of Compounds Labeled with Positron Nuclides Approved as Established Techniques for Medical Use (2001 Revision). Examples were the organization for manufacturing and management, standard format of the product (for [ 18 F]2-deoxy-2-fluoro-D-glucose), standard for process control of manufacture, standard for control of manufacturing and hygiene, standard for quality, and standard operating procedures for entering and leaving the manufacturing facility, for the clean-bench and for the test of floating micro-particles. The second item involved the definition of the cyclotron target ( 18 O), generation of 18 F by the reaction (p, n), purification of the product, and prescription: the third item; storage of the product and manufacturing process control: and the fourth; education and training of personnel, and health management. (K.H.)

IDENTIFICATION OF MEASUREMENT ITEMS OF DESIGN REQUIREMENTS FOR LEAN AND AGILE SUPPLY CHAIN-CONFIRMATORY FACTOR ANALYSIS

Directory of Open Access Journals (Sweden)

D.Venkata Ramana

2013-06-01

Full Text Available This study examines the consistency approaches by confirmatory factor analysis that determines the construct validity, convergent validity, construct reliability and internal consistency of the items of strategic design requirements. The design requirements includes use of information technology, sourcing procedures, new product development, flexible manufacturing functions and demand management supply chain net work design, management, commitment and inventory management policies among manufacturers of volatile and unforeseeable products in Andhraadesh, India. This study suggested that the seven factor model with 20 items of the leagile supply chain design requirements had a good fit. Further, the study showed a val id and reliable measurement to identify critical items among the design requirements of leagile supply chains.

Analysis of Culture-Specific Items and Translation Strategies Applied in Translating Jalal Al-Ahmad's "By the Pen"

Science.gov (United States)

Daghoughi, Shekoufeh; Hashemian, Mahmood

2016-01-01

Due to differences across languages, meanings and concepts vary across different languages, too. The most obvious points of difference between languages appear in their literature and their culture-specific items (CSIs), which lead to complexities when transferring meanings and concepts from one language into another. To overcome the complexities…

Few items in the thyroid-related quality of life instrument ThyPRO exhibited differential item functioning

DEFF Research Database (Denmark)

Watt, Torquil; Grønvold, Mogens; Hegedüs, Laszlo

2014-01-01

To evaluate the extent of differential item functioning (DIF) within the thyroid-specific quality of life patient-reported outcome measure, ThyPRO, according to sex, age, education and thyroid diagnosis.......To evaluate the extent of differential item functioning (DIF) within the thyroid-specific quality of life patient-reported outcome measure, ThyPRO, according to sex, age, education and thyroid diagnosis....

40 CFR 53.51 - Demonstration of compliance with design specifications and manufacturing and test requirements.

Science.gov (United States)

2010-07-01

... Methods and Class I and Class II Equivalent Methods for PM2.5 or PM10â2.5 § 53.51 Demonstration of... standard specification 8625F, Type II, Class I (reference 4 in appendix A of this subpart) in the same way... specifications and manufacturing and test requirements. 53.51 Section 53.51 Protection of Environment...

SENSITIVITY AND SPECIFICITY OF INDIVIDUAL BERG BALANCE ITEMS COMPARED WITH THE TOTAL SCORE TO PREDICT FALLS IN COMMUNITY DWELLING ELDERLY INDIVIDUALS

Directory of Open Access Journals (Sweden)

Hazel Denzil Dias

2014-09-01

Full Text Available Background: Falls are a major problem in the elderly leading to increased morbidity and mortality in this population. Scores from objective clinical measures of balance have frequently been associated with falls in older adults. The Berg Balance Score (BBS which is a frequently used scale to test balance impairments in the elderly ,takes time to perform and has been found to have scoring inconsistencies. The purpose was to determine if individual items or a group of BBS items would have better accuracy than the total BBS in classifying community dwelling elderly individuals according to fall history. Method: 60 community dwelling elderly individuals were chosen based on a history of falls in this cross sectional study. Each BBS item was dichotomized at three points along the scoring scale of 0 – 4: between scores of 1 and 2, 2 and 3, and 3 and 4. Sensitivity (Sn, specificity (Sp, and positive (+LR and negative (-LR likelihood ratios were calculated for all items for each scoring dichotomy based on their accuracy in classifying subjects with a history of multiple falls. These findings were compared with the total BBS score where the cut-off score was derived from receiver operating characteristic curve analysis. Results: On analysing a combination of BBS items, B9 and B11 were found to have the best sensitivity and specificity when considered together. However the area under the curve of these items was 0.799 which did not match that of the total score (AUC= 0.837. A, combination of 4 BBS items - B9 B11 B12 and B13 also had good Sn and Sp but the AUC was 0.815. The combination with the AUC closest to that of the total score was a combination items B11 and B13. (AUC= 0.824. hence these two items can be used as the best predictor of falls with a cut off of 6.5 The ROC curve of the Total Berg balance Scale scores revealed a cut off score of 48.5. Conclusion: This study showed that combination of items B11 and B13 may be best predictors of falls in

SENSITIVITY AND SPECIFICITY OF INDIVIDUAL BERG BALANCE ITEMS COMPARED WITH THE TOTAL SCORE TO PREDICT FALLS IN COMMUNITY DWELLING ELDERLY INDIVIDUALS

Directory of Open Access Journals (Sweden)

Hazel Denzil Dias

2014-06-01

Full Text Available Background: Falls are a major problem in the elderly leading to increased morbidity and mortality in this population. Scores from objective clinical measures of balance have frequently been associated with falls in older adults. The Berg Balance Score (BBS which is a frequently used scale to test balance impairments in the elderly ,takes time to perform and has been found to have scoring inconsistencies. The purpose was to determine if individual items or a group of BBS items would have better accuracy than the total BBS in classifying community dwelling elderly individuals according to fall history. Method: 60 community dwelling elderly individuals were chosen based on a history of falls in this cross sectional study. Each BBS item was dichotomized at three points along the scoring scale of 0 – 4: between scores of 1 and 2, 2 and 3, and 3 and 4. Sensitivity (Sn, specificity (Sp, and positive (+LR and negative (-LR likelihood ratios were calculated for all items for each scoring dichotomy based on their accuracy in classifying subjects with a history of multiple falls. These findings were compared with the total BBS score where the cut-off score was derived from receiver operating characteristic curve analysis. Results: On analysing a combination of BBS items, B9 and B11 were found to have the best sensitivity and specificity when considered together. However the area under the curve of these items was 0.799 which did not match that of the total score (AUC= 0.837. A, combination of 4 BBS items - B9 B11 B12 and B13 also had good Sn and Sp but the AUC was 0.815. The combination with the AUC closest to that of the total score was a combination items B11 and B13. (AUC= 0.824. hence these two items can be used as the best predictor of falls with a cut off of 6.5 The ROC curve of the Total Berg balance Scale scores revealed a cut off score of 48.5. Conclusion: This study showed that combination of items B11 and B13 may be best predictors of falls in

The role of attention in item-item binding in visual working memory.

Science.gov (United States)

Peterson, Dwight J; Naveh-Benjamin, Moshe

2017-09-01

An important yet unresolved question regarding visual working memory (VWM) relates to whether or not binding processes within VWM require additional attentional resources compared with processing solely the individual components comprising these bindings. Previous findings indicate that binding of surface features (e.g., colored shapes) within VWM is not demanding of resources beyond what is required for single features. However, it is possible that other types of binding, such as the binding of complex, distinct items (e.g., faces and scenes), in VWM may require additional resources. In 3 experiments, we examined VWM item-item binding performance under no load, articulatory suppression, and backward counting using a modified change detection task. Binding performance declined to a greater extent than single-item performance under higher compared with lower levels of concurrent load. The findings from each of these experiments indicate that processing item-item bindings within VWM requires a greater amount of attentional resources compared with single items. These findings also highlight an important distinction between the role of attention in item-item binding within VWM and previous studies of long-term memory (LTM) where declines in single-item and binding test performance are similar under divided attention. The current findings provide novel evidence that the specific type of binding is an important determining factor regarding whether or not VWM binding processes require attention. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Design for Additive Bio-Manufacturing: From Patient-Specific Medical Devices to Rationally Designed Meta-Biomaterials.

Science.gov (United States)

Zadpoor, Amir A

2017-07-25

Recent advances in additive manufacturing (AM) techniques in terms of accuracy, reliability, the range of processable materials, and commercial availability have made them promising candidates for production of functional parts including those used in the biomedical industry. The complexity-for-free feature offered by AM means that very complex designs become feasible to manufacture, while batch-size-indifference enables fabrication of fully patient-specific medical devices. Design for AM (DfAM) approaches aim to fully utilize those features for development of medical devices with substantially enhanced performance and biomaterials with unprecedented combinations of favorable properties that originate from complex geometrical designs at the micro-scale. This paper reviews the most important approaches in DfAM particularly those applicable to additive bio-manufacturing including image-based design pipelines, parametric and non-parametric designs, metamaterials, rational and computationally enabled design, topology optimization, and bio-inspired design. Areas with limited research have been identified and suggestions have been made for future research. The paper concludes with a brief discussion on the practical aspects of DfAM and the potential of combining AM with subtractive and formative manufacturing processes in so-called hybrid manufacturing processes.

Design for Additive Bio-Manufacturing: From Patient-Specific Medical Devices to Rationally Designed Meta-Biomaterials

Directory of Open Access Journals (Sweden)

Amir A. Zadpoor

2017-07-01

Full Text Available Recent advances in additive manufacturing (AM techniques in terms of accuracy, reliability, the range of processable materials, and commercial availability have made them promising candidates for production of functional parts including those used in the biomedical industry. The complexity-for-free feature offered by AM means that very complex designs become feasible to manufacture, while batch-size-indifference enables fabrication of fully patient-specific medical devices. Design for AM (DfAM approaches aim to fully utilize those features for development of medical devices with substantially enhanced performance and biomaterials with unprecedented combinations of favorable properties that originate from complex geometrical designs at the micro-scale. This paper reviews the most important approaches in DfAM particularly those applicable to additive bio-manufacturing including image-based design pipelines, parametric and non-parametric designs, metamaterials, rational and computationally enabled design, topology optimization, and bio-inspired design. Areas with limited research have been identified and suggestions have been made for future research. The paper concludes with a brief discussion on the practical aspects of DfAM and the potential of combining AM with subtractive and formative manufacturing processes in so-called hybrid manufacturing processes.

[Age- and sex-specific reference intervals for 10 health examination items: mega-data from a Japanese Health Service Association].

Science.gov (United States)

Suka, Machi; Yoshida, Katsumi; Kawai, Tadashi; Aoki, Yoshikazu; Yamane, Noriyuki; Yamauchi, Kuniaki

2005-07-01

To determine age- and sex-specific reference intervals for 10 health examination items in Japanese adults. Health examination data were accumulated from 24 different prefectural health service associations affiliated with the Japan Association of Health Service. Those who were non-smokers, drank less than 7 days/week, and had a body mass index of 18.5-24.9kg/m2 were sampled as a reference population (n = 737,538; 224,947 men and 512,591 women). After classified by age and sex, reference intervals for 10 health examination items (systolic blood pressure, diastolic blood pressure, total cholesterol, triglyceride, glucose, uric acid, AST, ALT, gamma-GT, and hemoglobin) were estimated using the parametric and nonparametric methods. In every item except for hemoglobin, men had higher reference intervals than women. Systolic blood pressure, total cholesterol, and glucose showed an upward trend in values with increasing age. Hemoglobin showed a downward trend in values with increasing age. Triglyceride, ALT, and gamma-GT reached a peak in middle age. Overall, parametric estimates showed narrower reference intervals than non-parametric estimates. Reference intervals vary with age and sex. Age- and sex-specific reference intervals may contribute to better assessment of health examination data.

Translation of Culture-Specific Items in Self-Help Literature: A Study on Domestication and Foreignization Strategies

Directory of Open Access Journals (Sweden)

Volga Yılmaz-Gümüş

2012-05-01

Full Text Available The last two decades have witnessed a boom in self-help materials in both global and local markets. This self-help trend, growing rapidly in our modern day, should be an area of interest for Translation Studies as an increasing number of self-help materials have been translated particularly from English every year. Self-help books involve a great deal of references to the material and social culture of the original country. One of the key issues in the translation of self-help books is the choice between foreignizing and domesticating these culture-specific items. This paper aims to discuss the procedures used for the translation of culture-specific items with regard to the particular function that these books assume in the target society. The analysis on the example of Outliers, a self-help book of sorts written by Malcolm Gladwell, has shown that the translator mostly adopted foreignizing strategies in translating the text into Turkish. The study also discusses whether these foreignizing strategies contribute to the fulfillment of target-text function, which is to provide quick-fix remedies to people struggling with modern-day challenges and demands.

Evaluation of item candidates for a diabetic retinopathy quality of life item bank.

Science.gov (United States)

Fenwick, Eva K; Pesudovs, Konrad; Khadka, Jyoti; Rees, Gwyn; Wong, Tien Y; Lamoureux, Ecosse L

2013-09-01

We are developing an item bank assessing the impact of diabetic retinopathy (DR) on quality of life (QoL) using a rigorous multi-staged process combining qualitative and quantitative methods. We describe here the first two qualitative phases: content development and item evaluation. After a comprehensive literature review, items were generated from four sources: (1) 34 previously validated patient-reported outcome measures; (2) five published qualitative articles; (3) eight focus groups and 18 semi-structured interviews with 57 DR patients; and (4) seven semi-structured interviews with diabetes or ophthalmic experts. Items were then evaluated during 3 stages, namely binning (grouping) and winnowing (reduction) based on key criteria and panel consensus; development of item stems and response options; and pre-testing of items via cognitive interviews with patients. The content development phase yielded 1,165 unique items across 7 QoL domains. After 3 sessions of binning and winnowing, items were reduced to a minimally representative set (n = 312) across 9 domains of QoL: visual symptoms; ocular surface symptoms; activity limitation; mobility; emotional; health concerns; social; convenience; and economic. After 8 cognitive interviews, 42 items were amended resulting in a final set of 314 items. We have employed a systematic approach to develop items for a DR-specific QoL item bank. The psychometric properties of the nine QoL subscales will be assessed using Rasch analysis. The resulting validated item bank will allow clinicians and researchers to better understand the QoL impact of DR and DR therapies from the patient's perspective.

Baking of the multi-itemed clinker by the large kiln; Ogata kirun ni yoru tahinshu kurinka no shosei

Energy Technology Data Exchange (ETDEWEB)

Kihara, Yasuhiro [Ube Industies, Ltd., Yamaguchi (Japan)

1998-10-10

In the Ube cement plant, it had 5 DB kilns, and it became a base of the special cement manufacture. However, the productivity difference with the special cement manufacture by the large kiln recently spread, and in the DB cairn, it was judged with the limit. Therefore, the rationalization which put together DB kiln of 5 in NSP kiln of 1 was carried out, while the role of the special cement manufacture base was maintained. In this paper, the outline of variety switching technology in large and single kiln of 1 for the multi-itemed and multi-itemed clinker production is introduced in this. (NEDO)

Beryllium irradiation embrittlement test programme. Material and specimen specification, manufacture and qualification

International Nuclear Information System (INIS)

Harries, D.R.; Dalle Donne, M.

1996-06-01

The report presents the specification, manufacture and qualification of the beryllium specimens to be irradiated in the BR2 reactor in Mol to investigate the effect of the neutron irradiation on the embrittlement as a function of temperature and beryllium oxide content. This work was been performed in the framework of the Nuclear Fusion Project of the Forschungszentrum Karlsruhe and is supported by the European Union within the European Fusion Technology Program. (orig.)

Manual on the selection of appropriate quality assurance programmes for items and services of a nuclear power plant

International Nuclear Information System (INIS)

1984-02-01

This manual provides guidance and illustrative examples for devising a system by which applicable quality assurance activities may be selected and applied to items and services in conformance with the requirements of the Code and the guidance of SG-QA 1. The selective application system described herein contains the following elements: (1) Classification of items and services; (2) Grading of quality assurance activities; (3) Correlation of applicable quality assurance activities with items and services; (4) Adaptation of selected quality assurance activities to the unique needs of the items or services; (5) Specifying of applicable quality assurance activities in bid specifications or in a contract. This selective application system is intended to be used by plant systems designers in the classifying of items (structures, components and materials) and related services; and by the organizations designing, manufacturing, installing and operating items or performing support services for such items in the specifying of applicable quality assurance activities that are to be implemented. The parts of the system should be developed to the degree and sophistication necessary for the particular needs of the project or organization. There are many methods and techniques that may be used effectively and those of one organization may not suit the purposes of another organization. It is important that the methodology of the system is developed with sufficient instructions documented to guide its consistent and disciplined execution

Interval availability analysis of a two-echelon, multi-item system

NARCIS (Netherlands)

Al Hanbali, Ahmad; van der Heijden, Matthijs C.

2011-01-01

In this paper we analyze the interval availability of a two-echelon, multi-item spare part inventory system. We consider a scenario inspired by a situation that we encountered at Thales Netherlands, a manufacturer of naval sensors and naval command and control systems. Modeling the complete system

A PetriNet-Based Approach for Supporting Traceability in Cyber-Physical Manufacturing Systems.

Science.gov (United States)

Huang, Jiwei; Zhu, Yeping; Cheng, Bo; Lin, Chuang; Chen, Junliang

2016-03-17

With the growing popularity of complex dynamic activities in manufacturing processes, traceability of the entire life of every product has drawn significant attention especially for food, clinical materials, and similar items. This paper studies the traceability issue in cyber-physical manufacturing systems from a theoretical viewpoint. Petri net models are generalized for formulating dynamic manufacturing processes, based on which a detailed approach for enabling traceability analysis is presented. Models as well as algorithms are carefully designed, which can trace back the lifecycle of a possibly contaminated item. A practical prototype system for supporting traceability is designed, and a real-life case study of a quality control system for bee products is presented to validate the effectiveness of the approach.

A PetriNet-Based Approach for Supporting Traceability in Cyber-Physical Manufacturing Systems

Directory of Open Access Journals (Sweden)

Jiwei Huang

2016-03-01

Full Text Available With the growing popularity of complex dynamic activities in manufacturing processes, traceability of the entire life of every product has drawn significant attention especially for food, clinical materials, and similar items. This paper studies the traceability issue in cyber-physical manufacturing systems from a theoretical viewpoint. Petri net models are generalized for formulating dynamic manufacturing processes, based on which a detailed approach for enabling traceability analysis is presented. Models as well as algorithms are carefully designed, which can trace back the lifecycle of a possibly contaminated item. A practical prototype system for supporting traceability is designed, and a real-life case study of a quality control system for bee products is presented to validate the effectiveness of the approach.

Critical success factors model developing for sustainable Kaizen implementation in manufactur-ing industry in Ethiopia

Directory of Open Access Journals (Sweden)

Haftu Hailu

2017-12-01

Full Text Available The purpose of the research is to identify critical success factors and model developing for sustaining kaizen implementation. Peacock shoe is one of the manufacturing industries in Ethiopia facing challenges on sustaining. The methodology followed is factor analysis and empirically testing hypothesis. A database was designed using SPSS version 20. The survey was validated using statistical validation using the Cronbach alpha index; the result is 0.908. The KMO index value was obtained for the 32 items and had a value of 0.642 with Bartlett's Test of Sphericity Approx. Chi-Square 4503.007, degree of freedom 496 and significance value 0.000. A factor analysis by principal components and varimax rotation was applied for finding the critical success factors. Finding designates that 32 items were merged into eight critical success factors. All the eight factors together explain for 76.941 % of the variance. Multiple regression model analysis has indicated that some of the critical success factors had relationship with success indicators. Due to constraint of time, the researcher focused only at peacock shoe manufacturing industry. Other limitation also includes the absence of any local research that shows the critical success factors at the moment.

Study on the inspection item and inspection method of HTGR fuel

International Nuclear Information System (INIS)

Na, Sang Ho; Kim, Y. K.; Jeong, K. C.; Oh, S. C.; Cho, M. S.; Kim, Y. M.; Lee, Y. W.

2006-01-01

The type of HTGR(High Temperature Gas-cooled Reactor) fuel is different according to the reactor type. Generally the HTGR fuel has two types. One is a block type, which is manufactured in Japan or America. And the other is a pebble type, which is manufactured in China. Regardless of the fuel type, the fuel manufacturing process started from the coated particle, which is consisted of fuel kernel and the 4 coating layers. Korea has a plan to fabricate a HTGR fuel in near future. The appropriate quality inspection standards are requested to produce a sound and reliable coated particle for HTGR fuel. Therefore, the inspection items and the inspection methods of HTGR fuel between Japan and China, which countries have the manufacturing process, are investigated to establish a proper inspection standards of our product characteristics

Item-focussed Trees for the Identification of Items in Differential Item Functioning.

Science.gov (United States)

Tutz, Gerhard; Berger, Moritz

2016-09-01

A novel method for the identification of differential item functioning (DIF) by means of recursive partitioning techniques is proposed. We assume an extension of the Rasch model that allows for DIF being induced by an arbitrary number of covariates for each item. Recursive partitioning on the item level results in one tree for each item and leads to simultaneous selection of items and variables that induce DIF. For each item, it is possible to detect groups of subjects with different item difficulties, defined by combinations of characteristics that are not pre-specified. The way a DIF item is determined by covariates is visualized in a small tree and therefore easily accessible. An algorithm is proposed that is based on permutation tests. Various simulation studies, including the comparison with traditional approaches to identify items with DIF, show the applicability and the competitive performance of the method. Two applications illustrate the usefulness and the advantages of the new method.

Computer Software Configuration Item-Specific Flight Software Image Transfer Script Generator

Science.gov (United States)

Bolen, Kenny; Greenlaw, Ronald

2010-01-01

A K-shell UNIX script enables the International Space Station (ISS) Flight Control Team (FCT) operators in NASA s Mission Control Center (MCC) in Houston to transfer an entire or partial computer software configuration item (CSCI) from a flight software compact disk (CD) to the onboard Portable Computer System (PCS). The tool is designed to read the content stored on a flight software CD and generate individual CSCI transfer scripts that are capable of transferring the flight software content in a given subdirectory on the CD to the scratch directory on the PCS. The flight control team can then transfer the flight software from the PCS scratch directory to the Electronically Erasable Programmable Read Only Memory (EEPROM) of an ISS Multiplexer/ Demultiplexer (MDM) via the Indirect File Transfer capability. The individual CSCI scripts and the CSCI Specific Flight Software Image Transfer Script Generator (CFITSG), when executed a second time, will remove all components from their original execution. The tool will identify errors in the transfer process and create logs of the transferred software for the purposes of configuration management.

Inventory Management Strategies For Productivity Improvement In Equipment Manufacturing Firms

Directory of Open Access Journals (Sweden)

T.T Amachree

2017-08-01

Full Text Available This study examined and developed Inventory Management Strategies IMS which could be creatively employed for Productivity Improvement in Equipment Firms PIEMF Equipment manufacturing projects suffer from declining productivity and inability to effectively satisfy customized order batch quantity within schedules budgeted cost and quality specifications due to lack of robust and well defined IMS as well as none code classification of vast number of inventory item. Survey and expost-facto research designs were adopted on the four identified IMS in three EMF. The method used for primary data collection and measurement on four IMS and inventory management parameters was questionnaire modelled into likert five point scale from the target respondents being experts in the subject matter. The secondary data was obtained from the computerised inventory status file of the three equipment manufacturing firms. The methods of primary data analysis and test of research used were Pearsons product moment correlation coefficient and oneway. Analysis of variance ANOVA computer software via Statistical Program for Social Science SPSS version 17 ABC analysis and classification of materials was used for code categorization of secondary data also with the aid of Microsoft excel. The results of the analyses highlighted and isolated A class of inventory items which are 137 out of 543 for Siemens Nig. Ltd 154 out of 551 for Dresser-Rand Nig. Ltd and 162 of 551 for Nigerian Engineering Works Ltd. The results of Pearson product moment correlation analysis and test of research hypotheses indicate that Materials Requirements Planning MRP followed by Supply Chain Management SCM are the most significant IMS as they correlate strongly with PIEMF. The study recommends IMS adoption by code classification of materials in which MRP or SCM could be deployed for management of A class of inventories while classical IMS could be used for management B and C classes of inventory items.

Resource-efficient proces chains to manufacture patient-specific prosthetic fingers

Directory of Open Access Journals (Sweden)

Hagedorn-Hansen, D.

2016-05-01

Full Text Available The high cost of quality prostheses, together with the lack of trained prosthetists, makes it challenging to obtain prosthetic devices in developing communities. Modern 3D digitising techniques and additive manufacturing (AM technologies are gaining popularity in the bio-medical industry and, in the case of prosthesis production, reduce the need for a trained prosthetist. The objective of this research was to develop a new resource-efficient process chain for the manufacturing of prosthetic fingers using additive manufacturing technologies, and to compare it with the traditional (Sculptor process chain. Fused deposition modelling (FDM, open-source FDM, 3-dimensional printing (3DP, and stereolithography (SLA were evaluated in terms of their costs, time, material usage, and aesthetic quality. The surface qualities produced with the different additive manufacturing technologies were also compared. The results showed that 3DP was the preferred technology and was the best candidate for the production of prosthesis in terms of cost, quality, and time for developing communities. SLA produced the highest aesthetic quality prosthesis, but was the most expensive. It was concluded that using the additive manufacturing technology process chain to produce prosthetic fingers is faster and more cost effective than the traditional method.

Reproducibility of the items on the Stroke Specific Quality of Life questionnaire that evaluate the participation component of the International Classification of Functioning, Disability and Health.

Science.gov (United States)

Silva, Soraia Micaela; Corrêa, Fernanda Ishida; Faria, Christina Danielli Coelho de Morais; Pereira, Gabriela Santos; Attié, Edna Alves Dos Anjos; Corrêa, João Carlos Ferrari

2016-12-01

To evaluate the reproducibility of the Stroke Specific Quality of Life (SS-QOL) items that address the participation component of the International Classification of Functioning, Disability and Health (ICF) and analyse the correlation between the subscore of these 26 items and the total SS-QOL score. Seventy-five stroke survivors participated in this study. Reproducibility was evaluated using the intraclass correlation coefficient (ICC2,1), standard error of measurement (SEM), minimum detectable change (MDC) and the Bland-Altman plot. The correlation between the subscore of the 26 items and the total SS-QOL score was analysed using Spearman's correlation coefficients (rho) and simple linear regression. An alpha risk ≤ 0.05 was considered for all analyses. The SS-QOL items that address the participation component of the ICF demonstrated excellent reliability (intra-rater ICC2,1 = 0.96; inter-rater ICC2,1 = 0.95). The SEM and MDC were adequate. The Bland-Altman plot demonstrated satisfactory agreement. A significant and strong correlation (rho = 0.83) was found between the 26 SS-QOL items that address participation and the total SS-QOL score. Moreover, the evaluation of participation was found to explain 73% of the evaluation of health-related quality of life. The 26 SS-QOL items that address the participation component of the ICF demonstrated adequate reproducibility. Thus, participation, which represents the social aspects of functionality, can be adequately evaluated with these items. Implications for Rehabilitation The 26 Stroke Specific Quality of Life items that address participation proved to be reproducible for the analysis of social participation following a stroke. The findings can lead to a better understanding of the social participation of individuals with chronic hemiparesis and assist in the establishment of adequate treatment for such individuals. The rehabilitation process can be directed towards more specific goals focused on the

A case study analysis of the application of design for manufacture principles by industrial design students

OpenAIRE

Marshall, R; Page, T

2016-01-01

This paper describes a case study evaluation of a module that engages students on product and industrial design programmes with the principles of Design for Manufacturing (DFM). The primary element of the module is to expose students to the constraints of a full design to manufacture process. The module explores the design of a small polymer promotional item, together with the means of mass producing that item. This is done through the process of injection moulding and students design an inje...

The selective application of quality assurance activities to nuclear power plant items and services

International Nuclear Information System (INIS)

Anderson, J.W.

1982-01-01

The definition of quality assurance and the criteria for a quality assurance programme that are contained in both national and international codes and standards provide the principle of selective application of quality assurance activities for cost-effective results. The effective implementation of this principle requires a systematic and disciplined methodology that should be established by or for the owner at the beginning of a nuclear power plant project. The methodology that has proven to be successful generally includes a uniform method of classifying plant items and services at their lowest level of unit assembly and using that classification in the selection of applicable quality assurance activities and the specification of appropriate requirements for those activities. The applicable quality assurance activities are those to be implemented by the organizations designing, manufacturing, installing and operating plant items or performing support services. The methods and techniques provided illustrate the methodology and are one way by which a nuclear power plant project may translate the principle into application in order to achieve the desired results. (author)

Customer Driven Uniform Manufacture (CDUM) Program. Customer Driven Uniform Management Apparel Research

Science.gov (United States)

2008-11-13

ABSTRACT (Maximum 200 Words) The DLA and DSCP sponsored Customer Driven Uniform Manufacturing (CDUM) program’s primary goals are to reduce total...functions that make decisions or consume apparel items. PDIT’s CDUM assignments were to create the web accessible database, create decision support tools...Manufacturing Monitoring Processes ....................................................40  Figure 32 – Assign Contract to Buyer

Additive Manufacturing in the Marine Corps

Science.gov (United States)

2015-06-01

TERMS additive manufacturing, 3D printing, improving logistics 15. NUMBER OF PAGES 123 16. PRICE CODE 17. SECURITY CLASSIFICATION OF REPORT...One such method is ultrasonic agglomeration. The process produces compact snack items that are nutrient-dense and shelf-stable. Currently Army...possess outdated technology. Additionally, prices for the printers are dropping significantly.202 Therefore, the Marine Corps will not only have outdated

Screening for depression in advanced disease: psychometric properties, sensitivity, and specificity of two items of the Palliative Care Outcome Scale (POS).

Science.gov (United States)

Antunes, Bárbara; Murtagh, Fliss; Bausewein, Claudia; Harding, Richard; Higginson, Irene J

2015-02-01

Depression is common among patients with advanced disease but often difficult to detect. To assess the Palliative care Outcome Scale (POS) (10 items) against the Geriatric Depression Scale (GDS)-10 total score and the Hospital Anxiety and Depression Scale (HADS)-Depression subscale total score and determine if the POS has appropriate items to screen for depression among people with advanced disease. This was a secondary analysis performed on five studies. Four psychometric properties were assessed: data quality, scaling assumptions, acceptability, and internal consistency (reliability). Receiver operating characteristic (ROC) curves were used to determine the area under the curve. Sensitivity, specificity, positive and negative predictive values, false positive and negative rates, and positive and negative likelihood ratios were computed. The overall sample had 416 patients from Germany and England: 144 had cancer and 267 had nonmalignant conditions. Prevalence of depression across the sample was 17.5%. Floor and ceiling effects were rare. Cronbach's alpha coefficients for POS items 7 and 8 summed, GDS-10 and HADS-Depression items varied: 0.61 (heart failure) and 0.80 (cancer). Two items combined (Item 7-feeling depressed and Item 8-feeling good about yourself) consistently presented the highest area under the ROC curve, ranging from 0.76 (95% CI 0.60, 0.93) (Germany, lung cancer) to 0.97 (95% CI 0.91, 1.0) (heart failure), highest negative predictive value, and lowest false negative rate. For the overall sample, the cutoff 2/3 presented a negative predictive value of 89.4% (95% CI 84.7, 92.8) and false negative rate of 10.6 (95% CI 7.2, 15.3). POS items 7 and 8 summed are potentially useful to screen for depression in advanced disease populations. Copyright © 2015 American Academy of Hospice and Palliative Medicine. Published by Elsevier Inc. All rights reserved.

Converging evidence for control of color-word Stroop interference at the item level.

Science.gov (United States)

Bugg, Julie M; Hutchison, Keith A

2013-04-01

Prior studies have shown that cognitive control is implemented at the list and context levels in the color-word Stroop task. At first blush, the finding that Stroop interference is reduced for mostly incongruent items as compared with mostly congruent items (i.e., the item-specific proportion congruence [ISPC] effect) appears to provide evidence for yet a third level of control, which modulates word reading at the item level. However, evidence to date favors the view that ISPC effects reflect the rapid prediction of high-contingency responses and not item-specific control. In Experiment 1, we first show that an ISPC effect is obtained when the relevant dimension (i.e., color) signals proportion congruency, a problematic pattern for theories based on differential response contingencies. In Experiment 2, we replicate and extend this pattern by showing that item-specific control settings transfer to new stimuli, ruling out alternative frequency-based accounts. In Experiment 3, we revert to the traditional design in which the irrelevant dimension (i.e., word) signals proportion congruency. Evidence for item-specific control, including transfer of the ISPC effect to new stimuli, is apparent when 4-item sets are employed but not when 2-item sets are employed. We attribute this pattern to the absence of high-contingency responses on incongruent trials in the 4-item set. These novel findings provide converging evidence for reactive control of color-word Stroop interference at the item level, reveal theoretically important factors that modulate reliance on item-specific control versus contingency learning, and suggest an update to the item-specific control account (Bugg, Jacoby, & Chanani, 2011).

Maintenance of item and order information in verbal working memory.

Science.gov (United States)

Camos, Valérie; Lagner, Prune; Loaiza, Vanessa M

2017-09-01

Although verbal recall of item and order information is well-researched in short-term memory paradigms, there is relatively little research concerning item and order recall from working memory. The following study examined whether manipulating the opportunity for attentional refreshing and articulatory rehearsal in a complex span task differently affected the recall of item- and order-specific information of the memoranda. Five experiments varied the opportunity for articulatory rehearsal and attentional refreshing in a complex span task, but the type of recall was manipulated between experiments (item and order, order only, and item only recall). The results showed that impairing attentional refreshing and articulatory rehearsal similarly affected recall regardless of whether the scoring procedure (Experiments 1 and 4) or recall requirements (Experiments 2, 3, and 5) reflected item- or order-specific recall. This implies that both mechanisms sustain the maintenance of item and order information, and suggests that the common cumulative functioning of these two mechanisms to maintain items could be at the root of order maintenance.

Developing a tool for the preparation of GMP audit of pharmaceutical contract manufacturer.

Science.gov (United States)

Linna, Anu; Korhonen, Mirka; Mannermaa, Jukka-Pekka; Airaksinen, Marja; Juppo, Anne Mari

2008-06-01

Outsourcing is rapidly growing in the pharmaceutical industry. When the manufacturing activities are outsourced, control of the product's quality has to be maintained. One way to confirm contract manufacturer's GMP (Good Manufacturing Practice) compliance is auditing. Audits can be supported for instance by using GMP questionnaires. The objective of this study was to develop a tool for the audit preparation of pharmaceutical contract manufacturers and to validate its contents by using Delphi method. At this phase of the study the tool was developed for non-sterile finished product contract manufacturers. A modified Delphi method was used with expert panel consisting of 14 experts from pharmaceutical industry, authorities and university. The content validity of the developed tool was assessed by a Delphi questionnaire round. The response rate in Delphi questionnaire round was 86%. The tool consisted of 103 quality items, from which 90 (87%) achieved the pre-defined agreement rate level (75%). Thirteen quality items which did not achieve the pre-defined agreement rate were excluded from the tool. The expert panel suggested only minor changes to the tool. The results show that the content validity of the developed audit preparation tool was good.

Complexities of three dimensional part geometry. [Ambiguities in specification of pieces for manufacture

Energy Technology Data Exchange (ETDEWEB)

Stark, R.H.

1977-05-01

This report is a non-technical exposition on the ambiguities in conventional specification of the shape of a part to be manufactured and on various alternatives for representing its geometry for computer processing. It touches lightly on wire-frame and bounded surface representations and on the concept of design by volumes. It concludes that no existing computer-aided design system has yet shown its long-range superiority over he spectrum of parts and of uses to which its information base should be applicable. 9 figures.

19 CFR Appendix B to Part 191 - Sample Formats for Applications for Specific Manufacturing Drawback Rulings

Science.gov (United States)

2010-04-01

... rulings must be submitted to and reviewed and approved by CBP Headquarters. A specific manufacturing... Ruling Under 19 U.S.C. 1313(a) and 1313(b) (Combination) COMPANY LETTERHEAD (Optional) U.S. Customs and.... Customs will not approve an application which shows an unincorporated division or company as the applicant...

Item validity vs. item discrimination index: a redundancy?

Science.gov (United States)

Panjaitan, R. L.; Irawati, R.; Sujana, A.; Hanifah, N.; Djuanda, D.

2018-03-01

In several literatures about evaluation and test analysis, it is common to find that there are calculations of item validity as well as item discrimination index (D) with different formula for each. Meanwhile, other resources said that item discrimination index could be obtained by calculating the correlation between the testee’s score in a particular item and the testee’s score on the overall test, which is actually the same concept as item validity. Some research reports, especially undergraduate theses tend to include both item validity and item discrimination index in the instrument analysis. It seems that these concepts might overlap for both reflect the test quality on measuring the examinees’ ability. In this paper, examples of some results of data processing on item validity and item discrimination index were compared. It would be discussed whether item validity and item discrimination index can be represented by one of them only or it should be better to present both calculations for simple test analysis, especially in undergraduate theses where test analyses were included.

SPECIFIC FEATURES OF TECHNOLOGY OF MANUFACTURING A ZINC-COATED TUB WIRE FOR MUZZLE (BOTTLE’ HOOD WIRE

Directory of Open Access Journals (Sweden)

D. B. Zuev

2016-01-01

Full Text Available The paper presents the main technical specifications of galvanized low carbon wire for muzzles (bottle’hood wire, consistent with the exploitation requirements to the wire in the manufacture and use of muzzles. The main criteria when selecting the steel grade and upon selection of the technological processes are given. 

Guideline for the seismic technical evaluation of replacement items for nuclear power plants

International Nuclear Information System (INIS)

Harris, S.P.; Cushing, R.W.; Johnson, H.W.; Abeles, J.M.

1993-02-01

Seismic qualification for equipment originally installed in nuclear power plants was typically performed by the original equipment suppliers or manufactures (OES/OEM). Many of the OES/OEM no longer maintain quality assurance programs with adequate controls for supplying nuclear equipment. Utilities themselves must provide reasonable assurance in the continued seismic adequacy of such replacement items. This guideline provides practical, cost-effective techniques which can be used to provide reasonable assurance that replacement items will meet seismic performance requirements necessary to maintain the seismic design basis of commercial nuclear power plants. It also provides a method for determining when a seismic technical evaluation of replacement items (STERI) is required as part of the procurement process for spare and replacement items. Guidance on supplier program requirements necessary to maintain continued seismic adequacy and on documentation of maintaining required seismic adequacy is also included

Macrostructural Treatment of Multi-word Lexical Items

Directory of Open Access Journals (Sweden)

Alenka Vrbinc

2011-05-01

Full Text Available The paper discusses the macrostructural treatment of multi-word lexical items in mono- and bilingual dictionaries. First, the classification of multi-word lexical items is presented, and special attention is paid to the discussion of compounds – a specific group of multi-word lexical items that is most commonly afforded headword status but whose inclusion in the headword list may also depend on spelling. Then the inclusion of multi-word lexical items in monolingual dictionaries is dealt with in greater detail, while the results of a short survey on the inclusion of five randomly chosen multi-word lexical items in seven English monolingual dictionaries are presented. The proposals as to how to treat these five multi-word lexical items in bilingual dictionaries are presented in the section about the inclusion of multi-word lexical items in bilingual dictionaries. The conclusion is that it is most important to take the users’ needs into consideration and to make any dictionary as user friendly as possible.

Divided attention enhances explicit but not implicit conceptual memory: an item-specific account of the attentional boost effect.

Science.gov (United States)

Spataro, Pietro; Mulligan, Neil W; Bechi Gabrielli, Giulia; Rossi-Arnaud, Clelia

2017-02-01

The Attentional Boost Effect (ABE) refers to the counterintuitive finding that words encoded with to-be-responded targets in a divided-attention condition are remembered better than words encoded with distractors. Previous studies suggested that the ABE-related enhancement of verbal memory depends upon the activation of abstract lexical representations. In the present study, we extend this hypothesis by embedding it in the context of a broader perspective, which proposes that divided attention in the ABE paradigm affects item-specific, but not relational, processing. To this purpose, we examined the ABE in the matched tasks of category-cued recall (CCRT: explicit memory) and category exemplar generation (CEGT: implicit memory). In addition, study time was varied (500, 1500 or 4000 ms), to further determine whether the attentional boost manipulation could influence late-phase elaborative processing. In agreement with the predictions of the item-specific account, the results showed that exemplars encoded with targets were recalled better than exemplars encoded with distractors in the CCRT, but not in the CEGT. Moreover, performance in the CCRT increased with study time, whereas the size of the ABE-related enhancement tended to decrease, further confirming that this effect hinges upon early phase encoding processes.

Three-item Direct Observation Screen (TIDOS) for autism spectrum disorder.

Science.gov (United States)

Oner, Pinar; Oner, Ozgur; Munir, Kerim

2014-08-01

We compared ratings on the Three-Item Direct Observation Screen test for autism spectrum disorders completed by pediatric residents with the Social Communication Questionnaire parent reports as an augmentative tool for improving autism spectrum disorder screening performance. We examined three groups of children (18-60 months) comparable in age (18-24 month, 24-36 month, 36-60 preschool subgroups) and gender distribution: n = 86 with Diagnostic and Statistical Manual of Mental Disorders (4th ed., text rev.) autism spectrum disorders; n = 76 with developmental delay without autism spectrum disorders; and n = 97 with typical development. The Three-Item Direct Observation Screen test included the following (a) Joint Attention, (b) Eye Contact, and (c) Responsiveness to Name. The parent Social Communication Questionnaire ratings had a sensitivity of .73 and specificity of .70 for diagnosis of autism spectrum disorders. The Three-Item Direct Observation Screen test item Joint Attention had a sensitivity of .82 and specificity of .90, Eye Contact had a sensitivity of .89 and specificity of .91, and Responsiveness to Name had a sensitivity of .67 and specificity of .87. In the Three-Item Direct Observation Screen test, having at least one of the three items positive had a sensitivity of .95 and specificity of .85. Age, diagnosis of autism spectrum disorder, and developmental level were important factors affecting sensitivity and specificity. The results indicate that augmentation of autism spectrum disorder screening by observational items completed by trained pediatric-oriented professionals can be a highly effective tool in improving screening performance. If supported by future population studies, the results suggest that primary care practitioners will be able to be trained to use this direct procedure to augment screening for autism spectrum disorders in the community. © The Author(s) 2013.

Hazardous metals in yellow items used in RCAs

International Nuclear Information System (INIS)

Brown, K.F.; Rankin, W.N.

1992-01-01

Yellow items used in Radiologically Controlled Areas (RCAs) that could contain hazardous metals were identified. X-ray fluorescence analyses indicated that thirty of the fifty-two items do contain hazardous metals. It is important to minimize the hazardous metals put into the wastes. The authors recommend that the specifications for all yellow items stocked in Stores be changed to specify that they contain no hazardous metals

Feed mechanism and method for feeding minute items

Science.gov (United States)

Stringer, Timothy Kent [Bucyrus, KS; Yerganian, Simon Scott [Lee's Summit, MO

2009-10-20

A feeding mechanism and method for feeding minute items, such as capacitors, resistors, or solder preforms. The mechanism is adapted to receive a plurality of the randomly-positioned and randomly-oriented extremely small or minute items, and to isolate, orient, and position one or more of the items in a specific repeatable pickup location wherefrom they may be removed for use by, for example, a computer-controlled automated assembly machine. The mechanism comprises a sliding shelf adapted to receive and support the items; a wiper arm adapted to achieve a single even layer of the items; and a pushing arm adapted to push the items into the pickup location. The mechanism can be adapted for providing the items with a more exact orientation, and can also be adapted for use in a liquid environment.

Achieving continuous manufacturing: technologies and approaches for synthesis, workup, and isolation of drug substance. May 20-21, 2014 Continuous Manufacturing Symposium.

Science.gov (United States)

Baxendale, Ian R; Braatz, Richard D; Hodnett, Benjamin K; Jensen, Klavs F; Johnson, Martin D; Sharratt, Paul; Sherlock, Jon-Paul; Florence, Alastair J

2015-03-01

This whitepaper highlights current challenges and opportunities associated with continuous synthesis, workup, and crystallization of active pharmaceutical ingredients (drug substances). We describe the technologies and requirements at each stage and emphasize the different considerations for developing continuous processes compared with batch. In addition to the specific sequence of operations required to deliver the necessary chemical and physical transformations for continuous drug substance manufacture, consideration is also given to how adoption of continuous technologies may impact different manufacturing stages in development from discovery, process development, through scale-up and into full scale production. The impact of continuous manufacture on drug substance quality and the associated challenges for control and for process safety are also emphasized. In addition to the technology and operational considerations necessary for the adoption of continuous manufacturing (CM), this whitepaper also addresses the cultural, as well as skills and training, challenges that will need to be met by support from organizations in order to accommodate the new work flows. Specific action items for industry leaders are: Develop flow chemistry toolboxes, exploiting the advantages of flow processing and including highly selective chemistries that allow use of simple and effective continuous workup technologies. Availability of modular or plug and play type equipment especially for workup to assist in straightforward deployment in the laboratory. As with learning from other industries, standardization is highly desirable and will require cooperation across industry and academia to develop and implement. Implement and exploit process analytical technologies (PAT) for real-time dynamic control of continuous processes. Develop modeling and simulation techniques to support continuous process development and control. Progress is required in multiphase systems such as

Importance of Advanced Planning of Manufacturing for Nuclear Industry

Directory of Open Access Journals (Sweden)

Shykinov Nick

2016-06-01

Full Text Available In the context of energy demands by growing economies, climate changes, fossil fuel pricing volatility, and improved safety and performance of nuclear power plants, many countries express interest in expanding or acquiring nuclear power capacity. In the light of the increased interest in expanding nuclear power the supply chain for nuclear power projects has received more attention in recent years. The importance of the advanced planning of procurement and manufacturing of components of nuclear facilities is critical for these projects. Many of these components are often referred to as long-lead items. They may be equipment, products and systems that are identified to have a delivery time long enough to affect directly the overall timing of a project. In order to avoid negatively affecting the project schedule, these items may need to be sourced out or manufactured years before the beginning of the project. For nuclear facilities, long-lead items include physical components such as large pressure vessels, instrumentation and controls. They may also mean programs and management systems important to the safety of the facility. Authorized nuclear operator training, site evaluation programs, and procurement are some of the examples. The nuclear power industry must often meet very demanding construction and commissioning timelines, and proper advanced planning of the long-lead items helps manage risks to project completion time. For nuclear components there are regulatory and licensing considerations that need to be considered. A national nuclear regulator must be involved early to ensure the components will meet the national legal regulatory requirements. This paper will discuss timing considerations to address the regulatory compliance of nuclear long-lead items.

An EPQ model with imperfect items using interval grey numbers

Directory of Open Access Journals (Sweden)

Erdal Aydemir

2015-01-01

Full Text Available The classic economic production quantity (EPQ model has been widely used to determine the optimal production quantity. However, the analysis for finding an EPQ model has many weaknesses which lead many researchers and practitioners to make extensions in several aspects on the original EPQ model. The basic assumption of EPQ model is that 100% of manufactured products are non-defective that is not valid for many production processes generally. The purpose of this paper is to develop an EPQ model with grey demand rate and cost values with maximum backorder level allowed with the good quality items in units under an imperfect production process. The imperfect items are considered to be low quality items which are sold to a particular purchaser at a lower price and, the others are reworked and scrapped. A mathematical model is developed and then an industrial example is presented on the wooden chipboard production process for illustration of the proposed model.

Managing the maintenance inventory of a cement manufacturer

Directory of Open Access Journals (Sweden)

Morne Eloff

2013-11-01

Full Text Available Inventory management is a crucial aspect of managing a company successfully. This is even more apparent in the case of maintenance inventories for production equipment, which impact directly on production equipment efficiency. This is a typical inventory management issue for a cement manufacturer that faces the problem of managing its maintenance inventories optimally when certain maintenance items have exceptionally long lead times (100 weeks and values in excess of R500 000. An assessment of the cement manufacturer’s approach to managing its maintenance inventories indicated various shortcomings, which have resulted in a significant level of obsolescence. One approach to managing maintenance inventories efficiently is to implement a classification of the inventory items in terms of their criticality to the cement production process. The critical nature of a component could be established through a risk-based approach (minimisation of the risk of production loss and taking into account the type of maintenance (planned vs unplanned that the component is required for. A risk-based approach should form the basis of the maintenance inventory management of the cement manufacturer as this would allow the cement manufacturer to utilise other inventory management methods effectively. In addition, it is important to ensure that employees are well versed in the different inventory management approaches utilised and that high levels of integration between departments are pursued.

Specificity of Good Manufacturing Practice (GMP) for Biomedical Cell Products.

Science.gov (United States)

Tulina, M A; Pyatigorskaya, N V

2018-03-01

The article describes special aspects of Good Manufacturing Practice (GMP) for biomedical cell products (BMCP) that imply high standards of aseptics throughout the entire productio process, strict requirements to donors and to the procedure of biomaterial isolation, guaranty of tracing BMCP products, defining processing procedures which allow to identify BMCP as minimally manipulated; continuous quality control and automation of the control process at all stages of manufacturing, which will ensure product release simultaneously with completion of technological operations.

A Production Model for Deteriorating Inventory Items with Production Disruptions

OpenAIRE

Yong He; Ju He

2010-01-01

Disruption management has recently become an active area of research. In this study, an extension is made to consider the fact that some products may deteriorate during storage. A production-inventory model for deteriorating items with production disruptions is developed. Then the optimal production and inventory plans are provided, so that the manufacturer can reduce the loss caused by disruptions. Finally, a numerical example is used to illustrate the model.

Managing dual warehouses with an incentive policy for deteriorating items

Science.gov (United States)

Yu, Jonas C. P.; Wang, Kung-Jeng; Lin, Yu-Siang

2016-02-01

Distributors in a supply chain usually limit their own warehouse in finite capacity for cost reduction and excess stock is held in a rent warehouse. In this study, we examine inventory control for deteriorating items in a two-warehouse setting. Assuming that there is an incentive offered by a rent warehouse that allows the rental fee to decrease over time, the objective of this study is to maximise the joint profit of the manufacturer and the distributor. An optimisation procedure is developed to derive the optimal joint economic lot size policy. Several criteria are identified to select the most appropriate warehouse configuration and inventory policy on the basis of storage duration of materials in a rent warehouse. Sensitivity analysis is done to examine the results of model robustness. The proposed model enables a manufacturer with a channel distributor to coordinate the use of alternative warehouses, and to maximise the joint profit of the manufacturer and the distributor.

Computational Process Modeling for Additive Manufacturing (OSU)

Science.gov (United States)

Bagg, Stacey; Zhang, Wei

2015-01-01

Powder-Bed Additive Manufacturing (AM) through Direct Metal Laser Sintering (DMLS) or Selective Laser Melting (SLM) is being used by NASA and the Aerospace industry to "print" parts that traditionally are very complex, high cost, or long schedule lead items. The process spreads a thin layer of metal powder over a build platform, then melts the powder in a series of welds in a desired shape. The next layer of powder is applied, and the process is repeated until layer-by-layer, a very complex part can be built. This reduces cost and schedule by eliminating very complex tooling and processes traditionally used in aerospace component manufacturing. To use the process to print end-use items, NASA seeks to understand SLM material well enough to develop a method of qualifying parts for space flight operation. Traditionally, a new material process takes many years and high investment to generate statistical databases and experiential knowledge, but computational modeling can truncate the schedule and cost -many experiments can be run quickly in a model, which would take years and a high material cost to run empirically. This project seeks to optimize material build parameters with reduced time and cost through modeling.

Screening for HIV-related PTSD: sensitivity and specificity of the 17-item Posttraumatic Stress Diagnostic Scale (PDS) in identifying HIV-related PTSD among a South African sample.

Science.gov (United States)

Martin, L; Fincham, D; Kagee, A

2009-11-01

The identification of HIV-positive patients who exhibit criteria for Posttraumatic Stress Disorder (PTSD) and related trauma symptomatology is of clinical importance in the maintenance of their overall wellbeing. This study assessed the sensitivity and specificity of the 17-item Posttraumatic Stress Diagnostic Scale (PDS), a self-report instrument, in the detection of HIV-related PTSD. An adapted version of the PTSD module of the Composite International Diagnostic Interview (CIDI) served as the gold standard. 85 HIV-positive patients diagnosed with HIV within the year preceding data collection were recruited by means of convenience sampling from three HIV clinics within primary health care facilities in the Boland region of South Africa. A significant association was found between the 17-item PDS and the adapted PTSD module of the CIDI. A ROC curve analysis indicated that the 17-item PDS correctly discriminated between PTSD caseness and non-caseness 74.9% of the time. Moreover, a PDS cut-off point of > or = 15 yielded adequate sensitivity (68%) and 1-specificity (65%). The 17-item PDS demonstrated a PPV of 76.0% and a NPV of 56.7%. The 17-item PDS can be used as a brief screening measure for the detection of HIV-related PTSD among HIV-positive patients in South Africa.

Enactment versus observation: item-specific and relational processing in goal-directed action sequences (and lists of single actions.

Directory of Open Access Journals (Sweden)

Janette Schult

Full Text Available What are the memory-related consequences of learning actions (such as "apply the patch" by enactment during study, as compared to action observation? Theories converge in postulating that enactment encoding increases item-specific processing, but not the processing of relational information. Typically, in the laboratory enactment encoding is studied for lists of unrelated single actions in which one action execution has no overarching purpose or relation with other actions. In contrast, real-life actions are usually carried out with the intention to achieve such a purpose. When actions are embedded in action sequences, relational information provides efficient retrieval cues. We contrasted memory for single actions with memory for action sequences in three experiments. We found more reliance on relational processing for action-sequences than single actions. To what degree can this relational information be used after enactment versus after the observation of an actor? We found indicators of superior relational processing after observation than enactment in ordered pair recall (Experiment 1A and in emerging subjective organization of repeated recall protocols (recall runs 2-3, Experiment 2. An indicator of superior item-specific processing after enactment compared to observation was recognition (Experiment 1B, Experiment 2. Similar net recall suggests that observation can be as good a learning strategy as enactment. We discuss possible reasons why these findings only partly converge with previous research and theorizing.

Using automatic item generation to create multiple-choice test items.

Science.gov (United States)

Gierl, Mark J; Lai, Hollis; Turner, Simon R

2012-08-01

Many tests of medical knowledge, from the undergraduate level to the level of certification and licensure, contain multiple-choice items. Although these are efficient in measuring examinees' knowledge and skills across diverse content areas, multiple-choice items are time-consuming and expensive to create. Changes in student assessment brought about by new forms of computer-based testing have created the demand for large numbers of multiple-choice items. Our current approaches to item development cannot meet this demand. We present a methodology for developing multiple-choice items based on automatic item generation (AIG) concepts and procedures. We describe a three-stage approach to AIG and we illustrate this approach by generating multiple-choice items for a medical licensure test in the content area of surgery. To generate multiple-choice items, our method requires a three-stage process. Firstly, a cognitive model is created by content specialists. Secondly, item models are developed using the content from the cognitive model. Thirdly, items are generated from the item models using computer software. Using this methodology, we generated 1248 multiple-choice items from one item model. Automatic item generation is a process that involves using models to generate items using computer technology. With our method, content specialists identify and structure the content for the test items, and computer technology systematically combines the content to generate new test items. By combining these outcomes, items can be generated automatically. © Blackwell Publishing Ltd 2012.

14 CFR 21.143 - Quality control data requirements; prime manufacturer.

Science.gov (United States)

2010-01-01

... with a chart indicating the functional relationship of the quality control organization to management..., purchased items, and parts and assemblies produced by manufacturers' suppliers including methods used to... delegation of authority to suppliers to make major inspections of parts or assemblies for which the prime...

Methodological quality of diagnostic accuracy studies on non-invasive coronary CT angiography: influence of QUADAS (Quality Assessment of Diagnostic Accuracy Studies included in systematic reviews) items on sensitivity and specificity

International Nuclear Information System (INIS)

Schueler, Sabine; Walther, Stefan; Schuetz, Georg M.; Schlattmann, Peter; Dewey, Marc

2013-01-01

To evaluate the methodological quality of diagnostic accuracy studies on coronary computed tomography (CT) angiography using the QUADAS (Quality Assessment of Diagnostic Accuracy Studies included in systematic reviews) tool. Each QUADAS item was individually defined to adapt it to the special requirements of studies on coronary CT angiography. Two independent investigators analysed 118 studies using 12 QUADAS items. Meta-regression and pooled analyses were performed to identify possible effects of methodological quality items on estimates of diagnostic accuracy. The overall methodological quality of coronary CT studies was merely moderate. They fulfilled a median of 7.5 out of 12 items. Only 9 of the 118 studies fulfilled more than 75 % of possible QUADAS items. One QUADAS item (''Uninterpretable Results'') showed a significant influence (P = 0.02) on estimates of diagnostic accuracy with ''no fulfilment'' increasing specificity from 86 to 90 %. Furthermore, pooled analysis revealed that each QUADAS item that is not fulfilled has the potential to change estimates of diagnostic accuracy. The methodological quality of studies investigating the diagnostic accuracy of non-invasive coronary CT is only moderate and was found to affect the sensitivity and specificity. An improvement is highly desirable because good methodology is crucial for adequately assessing imaging technologies. (orig.)

Methodological quality of diagnostic accuracy studies on non-invasive coronary CT angiography: influence of QUADAS (Quality Assessment of Diagnostic Accuracy Studies included in systematic reviews) items on sensitivity and specificity

Energy Technology Data Exchange (ETDEWEB)

Schueler, Sabine; Walther, Stefan; Schuetz, Georg M. [Humboldt-Universitaet zu Berlin, Freie Universitaet Berlin, Charite Medical School, Department of Radiology, Berlin (Germany); Schlattmann, Peter [University Hospital of Friedrich Schiller University Jena, Department of Medical Statistics, Informatics, and Documentation, Jena (Germany); Dewey, Marc [Humboldt-Universitaet zu Berlin, Freie Universitaet Berlin, Charite Medical School, Department of Radiology, Berlin (Germany); Charite, Institut fuer Radiologie, Berlin (Germany)

2013-06-15

To evaluate the methodological quality of diagnostic accuracy studies on coronary computed tomography (CT) angiography using the QUADAS (Quality Assessment of Diagnostic Accuracy Studies included in systematic reviews) tool. Each QUADAS item was individually defined to adapt it to the special requirements of studies on coronary CT angiography. Two independent investigators analysed 118 studies using 12 QUADAS items. Meta-regression and pooled analyses were performed to identify possible effects of methodological quality items on estimates of diagnostic accuracy. The overall methodological quality of coronary CT studies was merely moderate. They fulfilled a median of 7.5 out of 12 items. Only 9 of the 118 studies fulfilled more than 75 % of possible QUADAS items. One QUADAS item (''Uninterpretable Results'') showed a significant influence (P = 0.02) on estimates of diagnostic accuracy with ''no fulfilment'' increasing specificity from 86 to 90 %. Furthermore, pooled analysis revealed that each QUADAS item that is not fulfilled has the potential to change estimates of diagnostic accuracy. The methodological quality of studies investigating the diagnostic accuracy of non-invasive coronary CT is only moderate and was found to affect the sensitivity and specificity. An improvement is highly desirable because good methodology is crucial for adequately assessing imaging technologies. (orig.)

Use of Adult Patient Focus Groups to Develop the Initial Item Bank for a Cochlear Implant Quality-of-Life Instrument.

Science.gov (United States)

McRackan, Theodore R; Velozo, Craig A; Holcomb, Meredith A; Camposeo, Elizabeth L; Hatch, Jonathan L; Meyer, Ted A; Lambert, Paul R; Melvin, Cathy L; Dubno, Judy R

2017-10-01

No instrument exists to assess quality of life (QOL) in adult cochlear implant (CI) users that has been developed and validated using accepted scientific standards. To develop a CI-specific QOL instrument for adults in accordance with the Patient Reported Outcomes Measurement Information System (PROMIS) guidelines. As required in the PROMIS guidelines, patient focus groups participated in creation of the initial item bank. Twenty-three adult CI users were divided into 1 of 3 focus groups stratified by word recognition ability. Three moderator-led focus groups were conducted based on grounded theory on December 3, 2016. Two reviewers independently analyzed focus group recordings and transcripts, with a third reviewer available to resolve discrepancies. All data were reviewed and reported according to the Consolidated Criteria for Reporting Qualitative Research. The setting was a tertiary referral center. Coded focus group data. The 23 focus group participants (10 [43%] female; mean [range] age, 68.1 [46.2-84.2] years) represented a wide range of income levels, education levels, listening modalities, CI device manufacturers, duration of CI use, and age at implantation. Data saturation was determined to be reached before the conclusion of each of the focus groups. After analysis of the transcripts, the central themes identified were communication, emotion, environmental sounds, independence and work function, listening effort, social isolation and ability to socialize, and sound clarity. Cognitive interviews were carried out on 20 adult CI patients who did not participate in the focus groups to ensure item clarity. Based on these results, the initial QOL item bank and prototype were developed. Patient focus groups drawn from the target population are the preferred method of identifying content areas and domains for developing the item bank for a CI-specific QOL instrument. Compared with previously used methods, the use of patient-centered item development for a CI-specific

A closed-loop supply chain inventory model for manufacturer - Collector system with inspection, waste disposal and price-quality dependent return rate

Science.gov (United States)

Putri, Anissa Rianda; Jauhari, Wakhid Ahmad; Rosyidi, Cucuk Nur

2017-11-01

This paper studies a closed-loop supply chain inventory model, where the primary market demand is fulfilled by newly produced products and remanufactured products. We intend to integrate a manufacturer and a collector as a supply chain system. Used items are collected and will be inspected and sorted by the collector, and the return rate of used items is depended upon price and quality factor. Used items that aren't pass this process, will be considered as waste and undergone waste disposal process. Recoverable used items will be sent to the manufacturer for recovery process. This paper applies two types of the recovery process for used products, i.e. remanufacture and refurbish. The refurbished items are sold to a secondary market with lower price than primary market price. Further, the amount of recoverable items depend upon the acceptance level of the returned items. This proposed model gives an optimal solution by maximizing the joint total profit. Moreover, a numerical example is presented to describe the application of the model.

Few items in the thyroid-related quality of life instrument ThyPRO exhibited differential item functioning.

Science.gov (United States)

Watt, Torquil; Groenvold, Mogens; Hegedüs, Laszlo; Bonnema, Steen Joop; Rasmussen, Åse Krogh; Feldt-Rasmussen, Ulla; Bjorner, Jakob Bue

2014-02-01

To evaluate the extent of differential item functioning (DIF) within the thyroid-specific quality of life patient-reported outcome measure, ThyPRO, according to sex, age, education and thyroid diagnosis. A total of 838 patients with benign thyroid diseases completed the ThyPRO questionnaire (84 five-point items, 13 scales). Uniform and nonuniform DIF were investigated using ordinal logistic regression, testing for both statistical significance and magnitude (∆R(2) > 0.02). Scale level was estimated by the sum score, after purification. Twenty instances of DIF in 17 of the 84 items were found. Eight according to diagnosis, where the goiter scale was the one most affected, possibly due to differing perceptions in patients with auto-immune thyroid diseases compared to patients with simple goiter. Eight DIFs according to age were found, of which 5 were in positively worded items, which younger patients were more likely to endorse; one according to gender: women were more likely to report crying, and three according to educational level. The vast majority of DIF had only minor influence on the scale scores (0.1-2.3 points on the 0-100 scales), but two DIF corresponded to a difference of 4.6 and 9.8, respectively. Ordinal logistic regression identified DIF in 17 of 84 items. The potential impact of this on the present scales was low, but items displaying DIF could be avoided when developing abbreviated scales, where the potential impact of DIF (due to fewer items) will be larger.

Open manufacturing system using MMS service and object oriented manufacturing equipment

International Nuclear Information System (INIS)

Kim, Dong Hoon; Song, Jun Yeob; Kim, Sun Ho

2007-01-01

Manufacturing equipment should be integrated to construct CIM (Computer Integrated Manufacturing) environment, but several economical and technological difficulties may be arisen in case heterogeneous systems are integrated into each other. MMS (Manufacturing Message Specification) can be effective in such a case, but the problem is that MMS-related products are comparatively expensive and the existing manufacturing equipment mostly do not support MMS. This study was focused on developing a gateway suitable to a non-MMS-compatible CNC machine-tool, and on implementing OSI (Open System Interconnection) upper layer on TCP/IP. The development system was applied to a cell controller by means of heterogeneous equipment under CIM environment, and to evaluate interoperability and portability

An Interoperability Framework and Capability Profiling for Manufacturing Software

Science.gov (United States)

Matsuda, M.; Arai, E.; Nakano, N.; Wakai, H.; Takeda, H.; Takata, M.; Sasaki, H.

ISO/TC184/SC5/WG4 is working on ISO16100: Manufacturing software capability profiling for interoperability. This paper reports on a manufacturing software interoperability framework and a capability profiling methodology which were proposed and developed through this international standardization activity. Within the context of manufacturing application, a manufacturing software unit is considered to be capable of performing a specific set of function defined by a manufacturing software system architecture. A manufacturing software interoperability framework consists of a set of elements and rules for describing the capability of software units to support the requirements of a manufacturing application. The capability profiling methodology makes use of the domain-specific attributes and methods associated with each specific software unit to describe capability profiles in terms of unit name, manufacturing functions, and other needed class properties. In this methodology, manufacturing software requirements are expressed in terns of software unit capability profiles.

No Retrieval-Induced Forgetting Using Item-Specific Independent Cues: Evidence against a General Inhibitory Account

Science.gov (United States)

Camp, Gino; Pecher, Diane; Schmidt, Henk G.

2007-01-01

Retrieval practice with particular items from memory can impair the recall of related items on a later memory test. This retrieval-induced forgetting effect has been ascribed to inhibitory processes (M. C. Anderson & B. A. Spellman, 1995). A critical finding that distinguishes inhibitory from interference explanations is that forgetting is found…

The Role of Item Models in Automatic Item Generation

Science.gov (United States)

Gierl, Mark J.; Lai, Hollis

2012-01-01

Automatic item generation represents a relatively new but rapidly evolving research area where cognitive and psychometric theories are used to produce tests that include items generated using computer technology. Automatic item generation requires two steps. First, test development specialists create item models, which are comparable to templates…

Development and validation of a multidimensional measure of lean manufacturing

Directory of Open Access Journals (Sweden)

Juan A. Marin-Garcia

2010-02-01

Full Text Available In the last 30 years of research of lean manufacturing many different questionnaires was proposed to check the degree of the use of the concept. The set of the items used changed considerably from one investigation to another one. Until now isn’t appreciate a movement that converge towards the use, by the investigators, of a few instruments whose validity and reliability have been compared in different surroundings. In fact, the majority of investigations are based on ad-hoc questionnaires and a few of them present the questionnaire validation checking only the unidimensionality and -Cronbach. Nevertheless it seems to have a consensus in identifying 5 big constructs that compose the lean manufacturing (TQM, JIT, TPM, supply chain management and high-involvement. Our research has consisted of identifying and summarizing the models that have been published previously to add the items in constructs or sub-scales of constructs. Later we developed an integrating questionnaire, starting off of the items that appeared in previous investigations. Finally we realized the sub-scales and models validation through a confirmatory factorial analysis, using date of a sample of Spanish Sheltered Work Centre’s (N=128. Of all proposed models, the best an adjustment takes place with the first order model with 20 sub-scales. Our investigation contributes to an integrating vision of the published models and the lean manufacturing sub-scales validity and reliability verification raised by other investigators. Due to his confirming approach, it can serve as generalization of studies that had been realized in contexts with different samples to which we have used for the replication.

Assessing item fit for unidimensional item response theory models using residuals from estimated item response functions.

Science.gov (United States)

Haberman, Shelby J; Sinharay, Sandip; Chon, Kyong Hee

2013-07-01

Residual analysis (e.g. Hambleton & Swaminathan, Item response theory: principles and applications, Kluwer Academic, Boston, 1985; Hambleton, Swaminathan, & Rogers, Fundamentals of item response theory, Sage, Newbury Park, 1991) is a popular method to assess fit of item response theory (IRT) models. We suggest a form of residual analysis that may be applied to assess item fit for unidimensional IRT models. The residual analysis consists of a comparison of the maximum-likelihood estimate of the item characteristic curve with an alternative ratio estimate of the item characteristic curve. The large sample distribution of the residual is proved to be standardized normal when the IRT model fits the data. We compare the performance of our suggested residual to the standardized residual of Hambleton et al. (Fundamentals of item response theory, Sage, Newbury Park, 1991) in a detailed simulation study. We then calculate our suggested residuals using data from an operational test. The residuals appear to be useful in assessing the item fit for unidimensional IRT models.

Problems with the factor analysis of items: Solutions based on item response theory and item parcelling

Directory of Open Access Journals (Sweden)

Gideon P. De Bruin

2004-10-01

Full Text Available The factor analysis of items often produces spurious results in the sense that unidimensional scales appear multidimensional. This may be ascribed to failure in meeting the assumptions of linearity and normality on which factor analysis is based. Item response theory is explicitly designed for the modelling of the non-linear relations between ordinal variables and provides a strong alternative to the factor analysis of items. Items may also be combined in parcels that are more likely to satisfy the assumptions of factor analysis than do the items. The use of the Rasch rating scale model and the factor analysis of parcels is illustrated with data obtained with the Locus of Control Inventory. The results of these analyses are compared with the results obtained through the factor analysis of items. It is shown that the Rasch rating scale model and the factoring of parcels produce superior results to the factor analysis of items. Recommendations for the analysis of scales are made. Opsomming Die faktorontleding van items lewer dikwels misleidende resultate op, veral in die opsig dat eendimensionele skale as meerdimensioneel voorkom. Hierdie resultate kan dikwels daaraan toegeskryf word dat daar nie aan die aannames van lineariteit en normaliteit waarop faktorontleding berus, voldoen word nie. Itemresponsteorie, wat eksplisiet vir die modellering van die nie-liniêre verbande tussen ordinale items ontwerp is, bied ’n aantreklike alternatief vir die faktorontleding van items. Items kan ook in pakkies gegroepeer word wat meer waarskynlik aan die aannames van faktorontleding voldoen as individuele items. Die gebruik van die Rasch beoordelingskaalmodel en die faktorontleding van pakkies word aan die hand van data wat met die Lokus van Beheervraelys verkry is, gedemonstreer. Die resultate van hierdie ontledings word vergelyk met die resultate wat deur ‘n faktorontleding van die individuele items verkry is. Die resultate dui daarop dat die Rasch

Item information and discrimination functions for trinary PCM items

NARCIS (Netherlands)

Akkermans, Wies; Muraki, Eiji

1997-01-01

For trinary partial credit items the shape of the item information and the item discrimination function is examined in relation to the item parameters. In particular, it is shown that these functions are unimodal if δ2 – δ1 < 4 ln 2 and bimodal otherwise. The locations and values of the maxima are

GEOMETRIC COMPLEXITY ANALYSIS IN AN INTEGRATIVE TECHNOLOGY EVALUATION MODEL (ITEM FOR SELECTIVE LASER MELTING (SLM#

Directory of Open Access Journals (Sweden)

S. Merkt

2012-01-01

Full Text Available

ENGLISH ABSTRACT: Selective laser melting (SLM is becoming an economically viable choice for manufacturing complex serial parts. This paper focuses on a geometric complexity analysis as part of the integrative technology evaluation model (ITEM presented here. In contrast to conventional evaluation methodologies, the ITEM considers interactions between product and process innovations generated by SLM. The evaluation of manufacturing processes that compete with SLM is the main goal of ITEM. The paper includes a complexity analysis of a test part from Festo AG. The paper closes with a discussion of how the expanded design freedom of SLM can be used to improve company operations, and how the complexity analysis presented here can be seen as a starting point for feature-based complexity analysis..

AFRIKAANSE OPSOMMING: Selektiewe lasersmelting word geleidelik ’n gangbare ekonomiese keuse vir die vervaar-diging van opeenvolgende komplekse onderdele. Die navorsing is toegespits op die ontleding van meetkundige kompleksiteit as ’n gedeelte van ’n integrerende tegnologiese evalueringsmodel. Gemeet teen konvensionele evalueringsmodelle behandel die genoemde metode interaksies tussen produkte- en prosesinnovasies wat gegenereer word. Die navorsing behandel ’n kompleksiteitsontleding van ’n toetsonderdeel van die firma FESTO AG. Die resultaat toon hoe kompleksiteits-analise gebruik kan word as die vertrekpunt vir eienskapsgebaseerde analise.

Some manufacture and installation problems in experimental assemblies for fusion research

International Nuclear Information System (INIS)

Partridge, J.E.; Rappe, G.; Hoare, F.; McDonald, J.

1976-01-01

Many of the manufacturing problems encountered when developing specialised items of fusion apparatus are only solved after much experimentation and a good deal of trial and error. After the experiment is built such problems may be forgotten and are often not recorded so that subsequent workers in the same field may start with no past experience on which to build. The paper therefore highlights some of the manufacturing problems which have been solved during the construction of some of the experimental apparatus at Culham

Dissociative effects of orthographic distinctiveness in pure and mixed lists: an item-order account.

Science.gov (United States)

McDaniel, Mark A; Cahill, Michael; Bugg, Julie M; Meadow, Nathaniel G

2011-10-01

We apply the item-order theory of list composition effects in free recall to the orthographic distinctiveness effect. The item-order account assumes that orthographically distinct items advantage item-specific encoding in both mixed and pure lists, but at the expense of exploiting relational information present in the list. Experiment 1 replicated the typical free recall advantage of orthographically distinct items in mixed lists and the elimination of that advantage in pure lists. Supporting the item-order account, recognition performances indicated that orthographically distinct items received greater item-specific encoding than did orthographically common items in mixed and pure lists (Experiments 1 and 2). Furthermore, order memory (input-output correspondence and sequential contiguity effects) was evident in recall of pure unstructured common lists, but not in recall of unstructured distinct lists (Experiment 1). These combined patterns, although not anticipated by prevailing views, are consistent with an item-order account.

Optimized manufacturable porous materials

DEFF Research Database (Denmark)

Andreassen, Erik; Andreasen, Casper Schousboe; Jensen, Jakob Søndergaard

Topology optimization has been used to design two-dimensional material structures with specific elastic properties, but optimized designs of three-dimensional material structures are more scarsely seen. Partly because it requires more computational power, and partly because it is a major challenge...... to include manufacturing constraints in the optimization. This work focuses on incorporating the manufacturability into the optimization procedure, allowing the resulting material structure to be manufactured directly using rapid manufacturing techniques, such as selective laser melting/sintering (SLM....../S). The available manufacturing methods are best suited for porous materials (one constituent and void), but the optimization procedure can easily include more constituents. The elasticity tensor is found from one unit cell using the homogenization method together with a standard finite element (FE) discretization...

ABORTION ATTITUDES, 1984-1987-1988 - EFFECTS OF ITEM ORDER AND DIMENSIONALITY

NARCIS (Netherlands)

TENVERGERT, E; GILLESPIE, MW; KINGMA, J; KLASEN, H

The comparability of surveys is often hampered by differences in the item order of presentation. The major focus of the present study was to investigate whether a general item or a specific item at the beginning of the questionnaire would affect the endorsement as well as the scalability of a set of

Item level diagnostics and model - data fit in item response theory ...

African Journals Online (AJOL)

Item response theory (IRT) is a framework for modeling and analyzing item response data. Item-level modeling gives IRT advantages over classical test theory. The fit of an item score pattern to an item response theory (IRT) models is a necessary condition that must be assessed for further use of item and models that best fit ...

NFC based Inspection and Qualification Management (NIQM) System Preventing Counterfeit and Fraudulent Item

International Nuclear Information System (INIS)

Chang, Choong Koo; Kim, Young Joo

2013-01-01

Design, manufacturing, fabrication, transportation and installation of the devices and equipment for nuclear power plants shall be conducted under the thorough quality assurance program for the nuclear safety. However, from late in the 1980s, NRC began to issue a number of communications alerting licenses to issues involving counterfeit and fraudulent items. A number of incidents identified by the NRC in the 1980s and 1990s catalyzed the US nuclear industry to adopt standard precautions to guard against counterfeit items. The purpose of this paper is to develop the NFC (Near Field Communication) based Inspection and Qualification Management(NIQM) system preventing counterfeit and fraudulent items. NFC is one of the latest wireless communication technologies. As a short-range wireless connectivity technology, NFC offers safe-yet simple and intuitive-communication between electronic devices. As described above, NFC technology can be applied to the inspection and qualification management system very effectively to prevent counterfeit and fraudulent items. In addition, NIQM system can use existing data and information through the interface with legacy system

NFC based Inspection and Qualification Management (NIQM) System Preventing Counterfeit and Fraudulent Item

Energy Technology Data Exchange (ETDEWEB)

Chang, Choong Koo; Kim, Young Joo [KEPCO International Nuclear Graduate School, Ulsan (Korea, Republic of)

2013-10-15

Design, manufacturing, fabrication, transportation and installation of the devices and equipment for nuclear power plants shall be conducted under the thorough quality assurance program for the nuclear safety. However, from late in the 1980s, NRC began to issue a number of communications alerting licenses to issues involving counterfeit and fraudulent items. A number of incidents identified by the NRC in the 1980s and 1990s catalyzed the US nuclear industry to adopt standard precautions to guard against counterfeit items. The purpose of this paper is to develop the NFC (Near Field Communication) based Inspection and Qualification Management(NIQM) system preventing counterfeit and fraudulent items. NFC is one of the latest wireless communication technologies. As a short-range wireless connectivity technology, NFC offers safe-yet simple and intuitive-communication between electronic devices. As described above, NFC technology can be applied to the inspection and qualification management system very effectively to prevent counterfeit and fraudulent items. In addition, NIQM system can use existing data and information through the interface with legacy system.

Requirements for qualification of manufacture of the ITER Central Solenoid and Correction Coils

Energy Technology Data Exchange (ETDEWEB)

Libeyre, Paul, E-mail: paul.libeyre@iter.org [ITER Organization, Route de Vinon sur Verdon, 13115 St Paul lez Durance (France); Li, Hongwei [ITER China, 15B Fuxing Road, Beijing 100862 (China); Reiersen, Wayne [US ITER Project Office, 1055 Commerce Park Dr., Oak Ridge, TN 37831 (United States); Dolgetta, Nello; Jong, Cornelis; Lyraud, Charles; Mitchell, Neil; Laurenti, Adamo [ITER Organization, Route de Vinon sur Verdon, 13115 St Paul lez Durance (France); Sgobba, Stefano [CERN, CH-1211 Genève 23 (Switzerland); Turck, Bernard [ITER Organization, Route de Vinon sur Verdon, 13115 St Paul lez Durance (France); Martovetsky, Nicolai; Everitt, David; Freudenberg, K.; Litherland, Steve; Rosenblad, Peter [US ITER Project Office, 1055 Commerce Park Dr., Oak Ridge, TN 37831 (United States); Smith, John; Spitzer, Jeff [General Atomics, P.O. Box 85608, San Diego, CA 92186-5608 (United States); Wei, Jing; Dong, Xiaoyu; Fang, Chao [ASIPP, Shushan Hu Road 350, Hefei, Anhui 230031 (China); and others

2015-10-15

Highlights: • A manufacturing line is installed for the ITER Correction Coils. • A manufacturing line is under installation for the ITER Central Solenoid. • Qualification of the manufacturing procedures has started for both manufacturing lines and acceptance criteria set. • Winding procedure of Correction Coils is qualified. - Abstract: The manufacturing line of the ITER Correction Coils (CC) at ASIPP in Hefei (China) was completed in 2013 and the manufacturing line of the ITER Central Solenoid (CS) modules is under installation at General Atomic premises in Poway (USA). In both cases, before starting production of the first coils, qualification of the manufacturing procedures is achieved by the construction of a set of mock-ups and prototypes to demonstrate that design requirements defined by the ITER Organization are effectively met. For each qualification item, the corresponding mock-ups are presented with the tests to be performed and the related acceptance criteria. The first qualification results are discussed.

Medial temporal lobe contributions to cued retrieval of items and contexts.

Science.gov (United States)

Hannula, Deborah E; Libby, Laura A; Yonelinas, Andrew P; Ranganath, Charan

2013-10-01

Several models have proposed that different regions of the medial temporal lobes contribute to different aspects of episodic memory. For instance, according to one view, the perirhinal cortex represents specific items, parahippocampal cortex represents information regarding the context in which these items were encountered, and the hippocampus represents item-context bindings. Here, we used event-related functional magnetic resonance imaging (fMRI) to test a specific prediction of this model-namely, that successful retrieval of items from context cues will elicit perirhinal recruitment and that successful retrieval of contexts from item cues will elicit parahippocampal cortex recruitment. Retrieval of the bound representation in either case was expected to elicit hippocampal engagement. To test these predictions, we had participants study several item-context pairs (i.e., pictures of objects and scenes, respectively), and then had them attempt to recall items from associated context cues and contexts from associated item cues during a scanned retrieval session. Results based on both univariate and multivariate analyses confirmed a role for hippocampus in content-general relational memory retrieval, and a role for parahippocampal cortex in successful retrieval of contexts from item cues. However, we also found that activity differences in perirhinal cortex were correlated with successful cued recall for both items and contexts. These findings provide partial support for the above predictions and are discussed with respect to several models of medial temporal lobe function. Copyright © 2013 Elsevier Ltd. All rights reserved.

Medial Temporal Lobe Contributions to Cued Retrieval of Items and Contexts

Science.gov (United States)

Hannula, Deborah E.; Libby, Laura A.; Yonelinas, Andrew P.; Ranganath, Charan

2013-01-01

Several models have proposed that different regions of the medial temporal lobes contribute to different aspects of episodic memory. For instance, according to one view, the perirhinal cortex represents specific items, parahippocampal cortex represents information regarding the context in which these items were encountered, and the hippocampus represents item-context bindings. Here, we used event-related functional magnetic resonance imaging (fMRI) to test a specific prediction of this model – namely, that successful retrieval of items from context cues will elicit perirhinal recruitment and that successful retrieval of contexts from item cues will elicit parahippocampal cortex recruitment. Retrieval of the bound representation in either case was expected to elicit hippocampal engagement. To test these predictions, we had participants study several item-context pairs (i.e., pictures of objects and scenes, respectively), and then had them attempt to recall items from associated context cues and contexts from associated item cues during a scanned retrieval session. Results based on both univariate and multivariate analyses confirmed a role for hippocampus in content-general relational memory retrieval, and a role for parahippocampal cortex in successful retrieval of contexts from item cues. However, we also found that activity differences in perirhinal cortex were correlated with successful cued recall for both items and contexts. These findings provide partial support for the above predictions and are discussed with respect to several models of medial temporal lobe function. PMID:23466350

Guide to good practices for the development of test items

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-01-01

While the methodology used in developing test items can vary significantly, to ensure quality examinations, test items should be developed systematically. Test design and development is discussed in the DOE Guide to Good Practices for Design, Development, and Implementation of Examinations. This guide is intended to be a supplement by providing more detailed guidance on the development of specific test items. This guide addresses the development of written examination test items primarily. However, many of the concepts also apply to oral examinations, both in the classroom and on the job. This guide is intended to be used as guidance for the classroom and laboratory instructor or curriculum developer responsible for the construction of individual test items. This document focuses on written test items, but includes information relative to open-reference (open book) examination test items, as well. These test items have been categorized as short-answer, multiple-choice, or essay. Each test item format is described, examples are provided, and a procedure for development is included. The appendices provide examples for writing test items, a test item development form, and examples of various test item formats.

Harmonizing Measures of Cognitive Performance Across International Surveys of Aging Using Item Response Theory.

Science.gov (United States)

Chan, Kitty S; Gross, Alden L; Pezzin, Liliana E; Brandt, Jason; Kasper, Judith D

2015-12-01

To harmonize measures of cognitive performance using item response theory (IRT) across two international aging studies. Data for persons ≥65 years from the Health and Retirement Study (HRS, N = 9,471) and the English Longitudinal Study of Aging (ELSA, N = 5,444). Cognitive performance measures varied (HRS fielded 25, ELSA 13); 9 were in common. Measurement precision was examined for IRT scores based on (a) common items, (b) common items adjusted for differential item functioning (DIF), and (c) DIF-adjusted all items. Three common items (day of date, immediate word recall, and delayed word recall) demonstrated DIF by survey. Adding survey-specific items improved precision but mainly for HRS respondents at lower cognitive levels. IRT offers a feasible strategy for harmonizing cognitive performance measures across other surveys and for other multi-item constructs of interest in studies of aging. Practical implications depend on sample distribution and the difficulty mix of in-common and survey-specific items. © The Author(s) 2015.

[Research about re-evaluation of screening of traditonal Chinese medicine symptoms item of post-marketing medicine Xuezhikang].

Science.gov (United States)

He, Wei; Xie, Yanming; Wang, Yongyan

2011-10-01

The purpose of post-marketing Chinese medicine re-evaluation is to identify Chinese medicine clinical indications, while designing scientific and rational of Chinese medicine symptoms items are important to the result of symptoms re-evaluation. This study give screening of traditional Chinese medicine(TCM) symptoms item of post-marketing medicine Xuezhikang re-evaluation as example that reference to principle dyslipidemia clinical research, academic dissertations, Xuezhikang directions, clinical expert practice experience etc. while standardization those symptom names and screening 41 dyslipidemia common symptoms. Furthermore, this paper discuss about the accoerdance and announcements when screening symptoms item, so as to providing a research thread to manufacture PRO chart for post-marketing medicine re-evaluation.

Overview of Classical Test Theory and Item Response Theory for Quantitative Assessment of Items in Developing Patient-Reported Outcome Measures

Science.gov (United States)

Cappelleri, Joseph C.; Lundy, J. Jason; Hays, Ron D.

2014-01-01

Introduction The U.S. Food and Drug Administration’s patient-reported outcome (PRO) guidance document defines content validity as “the extent to which the instrument measures the concept of interest” (FDA, 2009, p. 12). “Construct validity is now generally viewed as a unifying form of validity for psychological measurements, subsuming both content and criterion validity” (Strauss & Smith, 2009, p. 7). Hence both qualitative and quantitative information are essential in evaluating the validity of measures. Methods We review classical test theory and item response theory approaches to evaluating PRO measures including frequency of responses to each category of the items in a multi-item scale, the distribution of scale scores, floor and ceiling effects, the relationship between item response options and the total score, and the extent to which hypothesized “difficulty” (severity) order of items is represented by observed responses. Conclusion Classical test theory and item response theory can be useful in providing a quantitative assessment of items and scales during the content validity phase of patient-reported outcome measures. Depending on the particular type of measure and the specific circumstances, either one or both approaches should be considered to help maximize the content validity of PRO measures. PMID:24811753

Benefits of deep encoding in Alzheimer disease. Analysis of performance on a memory task using the Item Specific Deficit Approach.

Science.gov (United States)

Oltra-Cucarella, J; Pérez-Elvira, R; Duque, P

2014-06-01

the aim of this study is to test the encoding deficit hypothesis in Alzheimer disease (AD) using a recent method for correcting memory tests. To this end, a Spanish-language adaptation of the Free and Cued Selective Reminding Test was interpreted using the Item Specific Deficit Approach (ISDA), which provides three indices: Encoding Deficit Index, Consolidation Deficit Index, and Retrieval Deficit Index. We compared the performances of 15 patients with AD and 20 healthy control subjects and analysed results using either the task instructions or the ISDA approach. patients with AD displayed deficient encoding of more than half the information, but items that were encoded properly could be retrieved later with the help of the same semantic clues provided individually during encoding. Virtually all the information retained over the long-term was retrieved by using semantic clues. Encoding was shown to be the most impaired process, followed by retrieval and consolidation. Discriminant function analyses showed that ISDA indices are more sensitive and specific for detecting memory impairments in AD than are raw scores. These results indicate that patients with AD present impaired information encoding, but they benefit from semantic hints that help them recover previously learned information. This should be taken into account for intervention techniques focusing on memory impairments in AD. Copyright © 2013 Sociedad Española de Neurología. Published by Elsevier Espana. All rights reserved.

A Bifactor Multidimensional Item Response Theory Model for Differential Item Functioning Analysis on Testlet-Based Items

Science.gov (United States)

Fukuhara, Hirotaka; Kamata, Akihito

2011-01-01

A differential item functioning (DIF) detection method for testlet-based data was proposed and evaluated in this study. The proposed DIF model is an extension of a bifactor multidimensional item response theory (MIRT) model for testlets. Unlike traditional item response theory (IRT) DIF models, the proposed model takes testlet effects into…

Gender-Based Differential Item Performance in Mathematics Achievement Items.

Science.gov (United States)

Doolittle, Allen E.; Cleary, T. Anne

1987-01-01

Eight randomly equivalent samples of high school seniors were each given a unique form of the ACT Assessment Mathematics Usage Test (ACTM). Signed measures of differential item performance (DIP) were obtained for each item in the eight ACTM forms. DIP estimates were analyzed and a significant item category effect was found. (Author/LMO)

Evaluation of psychometric properties and differential item functioning of 8-item Child Perceptions Questionnaires using item response theory.

Science.gov (United States)

Yau, David T W; Wong, May C M; Lam, K F; McGrath, Colman

2015-08-19

Four-factor structure of the two 8-item short forms of Child Perceptions Questionnaire CPQ11-14 (RSF:8 and ISF:8) has been confirmed. However, the sum scores are typically reported in practice as a proxy of Oral health-related Quality of Life (OHRQoL), which implied a unidimensional structure. This study first assessed the unidimensionality of 8-item short forms of CPQ11-14. Item response theory (IRT) was employed to offer an alternative and complementary approach of validation and to overcome the limitations of classical test theory assumptions. A random sample of 649 12-year-old school children in Hong Kong was analyzed. Unidimensionality of the scale was tested by confirmatory factor analysis (CFA), principle component analysis (PCA) and local dependency (LD) statistic. Graded response model was fitted to the data. Contribution of each item to the scale was assessed by item information function (IIF). Reliability of the scale was assessed by test information function (TIF). Differential item functioning (DIF) across gender was identified by Wald test and expected score functions. Both CPQ11-14 RSF:8 and ISF:8 did not deviate much from the unidimensionality assumption. Results from CFA indicated acceptable fit of the one-factor model. PCA indicated that the first principle component explained >30 % of the total variation with high factor loadings for both RSF:8 and ISF:8. Almost all LD statistic items suggesting little contribution of information to the scale and item removal caused little practical impact. Comparing the TIFs, RSF:8 showed slightly better information than ISF:8. In addition to oral symptoms items, the item "Concerned with what other people think" demonstrated a uniform DIF (p Items related to oral symptoms were not informative to OHRQoL and deletion of these items is suggested. The impact of DIF across gender on the overall score was minimal. CPQ11-14 RSF:8 performed slightly better than ISF:8 in measurement precision. The 6-item short forms

Item-nonspecific proactive interference in monkeys' auditory short-term memory.

Science.gov (United States)

Bigelow, James; Poremba, Amy

2015-09-01

Recent studies using the delayed matching-to-sample (DMS) paradigm indicate that monkeys' auditory short-term memory (STM) is susceptible to proactive interference (PI). During the task, subjects must indicate whether sample and test sounds separated by a retention interval are identical (match) or not (nonmatch). If a nonmatching test stimulus also occurred on a previous trial, monkeys are more likely to incorrectly make a "match" response (item-specific PI). However, it is not known whether PI may be caused by sounds presented on prior trials that are similar, but nonidentical to the current test stimulus (item-nonspecific PI). This possibility was investigated in two experiments. In Experiment 1, memoranda for each trial comprised tones with a wide range of frequencies, thus minimizing item-specific PI and producing a range of frequency differences among nonidentical tones. In Experiment 2, memoranda were drawn from a set of eight artificial sounds that differed from each other by one, two, or three acoustic dimensions (frequency, spectral bandwidth, and temporal dynamics). Results from both experiments indicate that subjects committed more errors when previously-presented sounds were acoustically similar (though not identical) to the test stimulus of the current trial. Significant effects were produced only by stimuli from the immediately previous trial, suggesting that item-nonspecific PI is less perseverant than item-specific PI, which can extend across noncontiguous trials. Our results contribute to existing human and animal STM literature reporting item-nonspecific PI caused by perceptual similarity among memoranda. Together, these observations underscore the significance of both temporal and discriminability factors in monkeys' STM. Copyright © 2015 Elsevier B.V. All rights reserved.

Commercial grade item (CGI) dedication of MDR relays for nuclear safety related applications

Science.gov (United States)

Das, Ranjit K.; Julka, Anil; Modi, Govind

1994-08-01

MDR relays manufactured by Potter & Brumfield (P&B) have been used in various safety related applications in commercial nuclear power plants. These include emergency safety features (ESF) actuation systems, emergency core cooling systems (ECCS) actuation, and reactor protection systems. The MDR relays manufactured prior to May 1990 showed signs of generic failure due to corrosion and outgassing of coil varnish. P&B has made design changes to correct these problems in relays manufactured after May 1990. However, P&B does not manufacture the relays under any 10CFR50 Appendix B quality assurance (QA) program. They manufacture the relays under their commercial QA program and supply these as commercial grade items. This necessitates CGI Dedication of these relays for use in nuclear-safety-related applications. This paper presents a CGI dedication program that has been used to dedicate the MDR relays manufactured after been used to dedicate the MDR relays manufactured after May 1990. The program is in compliance with current Nuclear Regulatory Commission (NRC) and Electric Power Research Institute (EPRI) guidelines and applicable industry standards; it specifies the critical characteristics of the relays, provides the tests and analysis required to verify the critical characteristics, the acceptance criteria for the test results, performs source verification to quality P&B for its control of the critical characteristics, and provides documentation. The program provides reasonable assurance that the new MDR relays will perform their intended safety functions.

Harnessing the Potential of Additive Manufacturing

Science.gov (United States)

2016-12-01

31 Defense AT&L: November-December 2016 Harnessing the Potential of Additive Manufacturing Bill Decker Decker is director of Technology...achieve its goal of competition throughout the acquisition life cycle. When we look at additive manufacturing , we have a much different environment. To...Titanium-6 Aluminum-4 Vanadium with Powder Bed Fusion. This specification covers additively manufactured titanium-6 aluminum-4 vanadium (Ti-6Al-4V

High Temperature Thermoplastic Additive Manufacturing Using Low-Cost, Open-Source Hardware

Science.gov (United States)

Gardner, John M.; Stelter, Christopher J.; Yashin, Edward A.; Siochi, Emilie J.

2016-01-01

Additive manufacturing (or 3D printing) via Fused Filament Fabrication (FFF), also known as Fused Deposition Modeling (FDM), is a process where material is placed in specific locations layer-by-layer to create a complete part. Printers designed for FFF build parts by extruding a thermoplastic filament from a nozzle in a predetermined path. Originally developed for commercial printers, 3D printing via FFF has become accessible to a much larger community of users since the introduction of Reprap printers. These low-cost, desktop machines are typically used to print prototype parts or novelty items. As the adoption of desktop sized 3D printers broadens, there is increased demand for these machines to produce functional parts that can withstand harsher conditions such as high temperature and mechanical loads. Materials meeting these requirements tend to possess better mechanical properties and higher glass transition temperatures (Tg), thus requiring printers with high temperature printing capability. This report outlines the problems and solutions, and includes a detailed description of the machine design, printing parameters, and processes specific to high temperature thermoplastic 3D printing.

Valuation of the light intensity from curing lamps of the students of odontology of the Universidad de Costa Rica during 2011, with respect to the manufacturer's specifications

International Nuclear Information System (INIS)

Solano Badilla, Lucrecia

2011-01-01

The behavior of the light intensity from halogens curing lamps used by students at the Facultad de Odontologia of the Universidad de Costa Rica (UCR) is studied with respect to the manufacturer's specifications of the lamp and the resin. The distribution of the type of curing lamp per student is described, as well as some characteristics of them. The light intensity mW/cm 2 of the curing lamps operated by students at the Facultad de Odontologia is compared with the manufacturer's specifications of the lamp. The light intensity mW/cm 2 is compared with the manufacturer's specifications of the resin utilized, by brand, by students of the Facultad de Odontologia of the UCR for their photopolymerization [es

Manufacturing tolerant topology optimization

DEFF Research Database (Denmark)

Sigmund, Ole

2009-01-01

In this paper we present an extension of the topology optimization method to include uncertainties during the fabrication of macro, micro and nano structures. More specifically, we consider devices that are manufactured using processes which may result in (uniformly) too thin (eroded) or too thick...... (dilated) structures compared to the intended topology. Examples are MEMS devices manufactured using etching processes, nano-devices manufactured using e-beam lithography or laser micro-machining and macro structures manufactured using milling processes. In the suggested robust topology optimization...... approach, under- and over-etching is modelled by image processing-based "erode" and "dilate" operators and the optimization problem is formulated as a worst case design problem. Applications of the method to the design of macro structures for minimum compliance and micro compliant mechanisms show...

13 CFR 121.407 - What are the size procedures for multiple item procurements?

Science.gov (United States)

2010-01-01

... Requirements for Government Procurement § 121.407 What are the size procedures for multiple item procurements? If a procurement calls for two or more specific end items or types of services with different size... multiple item procurements? 121.407 Section 121.407 Business Credit and Assistance SMALL BUSINESS...

19 CFR 191.24 - Certificate of manufacture and delivery.

Science.gov (United States)

2010-04-01

... Section 191.24 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY... manufactured or produced under a general manufacturing drawback ruling, the unique computer-generated number... manufactured or produced under a specific manufacturing drawback ruling, either the unique computer number or...

Credit financing for deteriorating imperfect quality items with allowable shortages

Directory of Open Access Journals (Sweden)

Aditi Khanna

2016-01-01

Full Text Available The outset of new technologies, systems and applications in manufacturing sector has no doubt lighten up our workload, yet the chance causes of variation in production system cannot be eliminated completely. Every produced/ordered lot may have some fraction of defectives which may vary from process to process. In addition the situation is more susceptible when the items are deteriorating in nature. However, the defective items can be secluded from the good quality lot through a careful inspection process. Thus, a screening process is obligatory in today’s technology driven industry which has the customer satisfaction as its only motto. Moreover, in order to survive in the current global markets, credit financing has been proven a very influential promotional tool to attract new customers and a good inducement policy for the retailers. Keeping this scenario in mind, the present paper investigates an inventory model for a retailer dealing with imperfect quality deteriorating items under permissible delay in payments. Shortages are allowed and fully backlogged. This model jointly optimizes the order quantity and shortages by maximizing the expected total profit. A mathematical model is developed to depict this scenario. Results have been validated with the help of numerical example. Comprehensive sensitivity analysis has also been presented.

Are the determinants of markup size industry-specific? The case of Slovenian manufacturing firms

Directory of Open Access Journals (Sweden)

Ponikvar Nina

2011-01-01

Full Text Available The aim of this paper is to identify factors that affect the pricing policy in Slovenian manufacturing firms in terms of the markup size and, most of all, to explicitly account for the possibility of differences in pricing procedures among manufacturing industries. Accordingly, the analysis of the dynamic panel is carried out on an industry-by-industry basis, allowing the coefficients on the markup determinants to vary across industries. We find that the oligopoly theory of markup determination for the most part holds for the manufacturing sector as a whole, although large variability in markup determinants exists across industries within the Slovenian manufacturing. Our main conclusion is that each industry should be investigated separately in detail in order to assess the precise role of markup factors in the markup-determination process.

49 CFR 178.33-6 - Manufacture.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Manufacture. 178.33-6 Section 178.33-6 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY... Specifications for Inside Containers, and Linings § 178.33-6 Manufacture. (a) By appliances and methods that will...

49 CFR 178.360-2 - Manufacture.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Manufacture. 178.360-2 Section 178.360-2 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY... Specifications for Packagings for Class 7 (Radioactive) Materials § 178.360-2 Manufacture. The ends of the vessel...

Bioprinting: an assessment based on manufacturing readiness levels.

Science.gov (United States)

Wu, Changsheng; Wang, Ben; Zhang, Chuck; Wysk, Richard A; Chen, Yi-Wen

2017-05-01

Over the last decade, bioprinting has emerged as a promising technology in the fields of tissue engineering and regenerative medicine. With recent advances in additive manufacturing, bioprinting is poised to provide patient-specific therapies and new approaches for tissue and organ studies, drug discoveries and even food manufacturing. Manufacturing Readiness Level (MRL) is a method that has been applied to assess manufacturing maturity and to identify risks and gaps in technology-manufacturing transitions. Technology Readiness Level (TRL) is used to evaluate the maturity of a technology. This paper reviews recent advances in bioprinting following the MRL scheme and addresses corresponding MRL levels of engineering challenges and gaps associated with the translation of bioprinting from lab-bench experiments to ultimate full-scale manufacturing of tissues and organs. According to our step-by-step TRL and MRL assessment, after years of rigorous investigation by the biotechnology community, bioprinting is on the cusp of entering the translational phase where laboratory research practices can be scaled up into manufacturing products specifically designed for individual patients.

14 CFR 35.17 - Materials and manufacturing methods.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Materials and manufacturing methods. 35.17... AIRWORTHINESS STANDARDS: PROPELLERS Design and Construction § 35.17 Materials and manufacturing methods. (a) The... and manufacturing methods must conform to specifications acceptable to the Administrator. (c) The...

The Body Appreciation Scale-2: item refinement and psychometric evaluation.

Science.gov (United States)

Tylka, Tracy L; Wood-Barcalow, Nichole L

2015-01-01

Considered a positive body image measure, the 13-item Body Appreciation Scale (BAS; Avalos, Tylka, & Wood-Barcalow, 2005) assesses individuals' acceptance of, favorable opinions toward, and respect for their bodies. While the BAS has accrued psychometric support, we improved it by rewording certain BAS items (to eliminate sex-specific versions and body dissatisfaction-based language) and developing additional items based on positive body image research. In three studies, we examined the reworded, newly developed, and retained items to determine their psychometric properties among college and online community (Amazon Mechanical Turk) samples of 820 women and 767 men. After exploratory factor analysis, we retained 10 items (five original BAS items). Confirmatory factor analysis upheld the BAS-2's unidimensionality and invariance across sex and sample type. Its internal consistency, test-retest reliability, and construct (convergent, incremental, and discriminant) validity were supported. The BAS-2 is a psychometrically sound positive body image measure applicable for research and clinical settings. Copyright © 2014 Elsevier Ltd. All rights reserved.

Topology Optimization for Additive Manufacturing

DEFF Research Database (Denmark)

Clausen, Anders

This PhD thesis deals with the combination of topology optimization and additive man-ufacturing (AM, also known as 3D-printing). In addition to my own works, the thesis contains a broader review and assessment of the literature within the field. The thesis first presents a classification...... of the various AM technologies, a review of relevant manufacturing materials, the properties of these materials in the additively manufactured part, as well as manufacturing constraints with a potential for design optimization. Subsequently, specific topology optimization formulations relevant for the most im...... for scalable manufacturing. In relation to interface problems it is shown how a flexible void area may be included into a standard minimum compliance problem by employing an additional design variable field and a sensitivity filter. Furthermore, it is shown how the design of coated structures may be modeled...

Converging Evidence for Control of Color-Word Stroop Interference at the Item Level

Science.gov (United States)

Bugg, Julie M.; Hutchison, Keith A.

2013-01-01

Prior studies have shown that cognitive control is implemented at the list and context levels in the color-word Stroop task. At first blush, the finding that Stroop interference is reduced for mostly incongruent items as compared with mostly congruent items (i.e., the item-specific proportion congruence [ISPC] effect) appears to provide evidence…

Regulation on the manufacture of radioactive medicines

International Nuclear Information System (INIS)

1977-01-01

This is the latest revision of the regulation which provides for the control of the manufacture of the said medicines in accordance with the Medical Drugs Act (Law No. 145, 1960). Schedule 1 to Article 1 which specifies the items of the radioactive medicines has been modified: several substances including their compounds and medicines made from them are added to, or omitted from the Schedule, such as; (added to) 11 C, 13 N, 15 O, sup(85m)Kr, 81 Rb and 123 I, (omitted from) 89 Sr, 91 y and 137 Cs. (Matsushima, A.)

Using the Nudge and Shove Methods to Adjust Item Difficulty Values.

Science.gov (United States)

Royal, Kenneth D

2015-01-01

In any examination, it is important that a sufficient mix of items with varying degrees of difficulty be present to produce desirable psychometric properties and increase instructors' ability to make appropriate and accurate inferences about what a student knows and/or can do. The purpose of this "teaching tip" is to demonstrate how examination items can be affected by the quality of distractors, and to present a simple method for adjusting items to meet difficulty specifications.

Mathematical modeling of a multi-product EMQ model with an enhanced end items issuing policy and failures in rework.

Science.gov (United States)

Chiu, Yuan-Shyi Peter; Sung, Peng-Cheng; Chiu, Singa Wang; Chou, Chung-Li

2015-01-01

This study uses mathematical modeling to examine a multi-product economic manufacturing quantity (EMQ) model with an enhanced end items issuing policy and rework failures. We assume that a multi-product EMQ model randomly generates nonconforming items. All of the defective are reworked, but a certain portion fails and becomes scraps. When rework process ends and the entire lot of each product is quality assured, a cost reduction n + 1 end items issuing policy is used to transport finished items of each product. As a result, a closed-form optimal production cycle time is obtained. A numerical example demonstrates the practical usage of our result and confirms a significant savings in stock holding and overall production costs as compared to that of a prior work (Chiu et al. in J Sci Ind Res India, 72:435-440 2013) in the literature.

Research for new materials manufacturing using XAFS. Around the non-crystal materials

International Nuclear Information System (INIS)

Sakurai, Masaki

2000-01-01

In the new materials manufacturing it becomes important to control its structure in nano-scale. The fine structure analysis using XAFS with the proton factory is also useful for the manufacturing. The following two items are reported. 1) The new materials manufacturing from amorphous state is very useful through the control of super cooling state and through the doping of a very small amount of additive elements; Radial distribution analysis using XAFS is important for understanding of the concentration fluctuation in the amorphous. 2) The new materials manufacturing from the cluster as a raw materials; Manufacturing the new materials from the cluster is very useful method through the condensation of the cluster of through the distribution the cluster in the matrix. The magic number clusters such as Me9O6, Me13O8, Me22O12 and Me43O20 (Me=Fe, Co, Ni) are observed they are much stable in comparing with other clusters. These magic number clusters are expected to be useful for the new material manufacturing. For the control of the cluster formation the in-situ analysis using LVCS is important in understanding the cluster formation process. (H. Katsuta)

A single exercise bout enhances the manufacture of viral-specific T-cells from healthy donors: implications for allogeneic adoptive transfer immunotherapy.

Science.gov (United States)

Spielmann, Guillaume; Bollard, Catherine M; Kunz, Hawley; Hanley, Patrick J; Simpson, Richard J

2016-05-16

Cytomegalovirus (CMV) and Epstein-Barr virus (EBV) infections remain a major cause of morbidity and mortality after allogeneic hematopoietic stem cell transplantation (HSCT). The adoptive transfer of donor-derived viral-specific cytotoxic T-cells (VSTs) is an effective treatment for controlling CMV and EBV infections after HSCT; however, new practical methods are required to augment the ex vivo manufacture of multi-VSTs from healthy donors. This study investigated the effects of a single exercise bout on the ex vivo manufacture of multi-VSTs. PBMCs isolated from healthy CMV/EBV seropositive participants before (PRE) and immediately after (POST) 30-minutes of cycling exercise were stimulated with CMV (pp65 and IE1) and EBV (LMP2A and BMLF1) peptides and expanded over 8 days. The number (fold difference from PRE) of T-cells specific for CMV pp65 (2.6), EBV LMP2A (2.5), and EBV BMLF1 (4.4) was greater among the VSTs expanded POST. VSTs expanded PRE and POST had similar phenotype characteristics and were equally capable of MHC-restricted killing of autologous target cells. We conclude that a single exercise bout enhances the manufacture of multi-VSTs from healthy donors without altering their phenotype or function and may serve as a simple and economical adjuvant to boost the production of multi-VSTs for allogeneic adoptive transfer immunotherapy.

Three Modeling Applications to Promote Automatic Item Generation for Examinations in Dentistry.

Science.gov (United States)

Lai, Hollis; Gierl, Mark J; Byrne, B Ellen; Spielman, Andrew I; Waldschmidt, David M

2016-03-01

Test items created for dentistry examinations are often individually written by content experts. This approach to item development is expensive because it requires the time and effort of many content experts but yields relatively few items. The aim of this study was to describe and illustrate how items can be generated using a systematic approach. Automatic item generation (AIG) is an alternative method that allows a small number of content experts to produce large numbers of items by integrating their domain expertise with computer technology. This article describes and illustrates how three modeling approaches to item content-item cloning, cognitive modeling, and image-anchored modeling-can be used to generate large numbers of multiple-choice test items for examinations in dentistry. Test items can be generated by combining the expertise of two content specialists with technology supported by AIG. A total of 5,467 new items were created during this study. From substitution of item content, to modeling appropriate responses based upon a cognitive model of correct responses, to generating items linked to specific graphical findings, AIG has the potential for meeting increasing demands for test items. Further, the methods described in this study can be generalized and applied to many other item types. Future research applications for AIG in dental education are discussed.

Good Manufacturing Practices (GMP) manufacturing of advanced therapy medicinal products: a novel tailored model for optimizing performance and estimating costs.

Science.gov (United States)

Abou-El-Enein, Mohamed; Römhild, Andy; Kaiser, Daniel; Beier, Carola; Bauer, Gerhard; Volk, Hans-Dieter; Reinke, Petra

2013-03-01

Advanced therapy medicinal products (ATMP) have gained considerable attention in academia due to their therapeutic potential. Good Manufacturing Practice (GMP) principles ensure the quality and sterility of manufacturing these products. We developed a model for estimating the manufacturing costs of cell therapy products and optimizing the performance of academic GMP-facilities. The "Clean-Room Technology Assessment Technique" (CTAT) was tested prospectively in the GMP facility of BCRT, Berlin, Germany, then retrospectively in the GMP facility of the University of California-Davis, California, USA. CTAT is a two-level model: level one identifies operational (core) processes and measures their fixed costs; level two identifies production (supporting) processes and measures their variable costs. The model comprises several tools to measure and optimize performance of these processes. Manufacturing costs were itemized using adjusted micro-costing system. CTAT identified GMP activities with strong correlation to the manufacturing process of cell-based products. Building best practice standards allowed for performance improvement and elimination of human errors. The model also demonstrated the unidirectional dependencies that may exist among the core GMP activities. When compared to traditional business models, the CTAT assessment resulted in a more accurate allocation of annual expenses. The estimated expenses were used to set a fee structure for both GMP facilities. A mathematical equation was also developed to provide the final product cost. CTAT can be a useful tool in estimating accurate costs for the ATMPs manufactured in an optimized GMP process. These estimates are useful when analyzing the cost-effectiveness of these novel interventions. Copyright © 2013 International Society for Cellular Therapy. Published by Elsevier Inc. All rights reserved.

Study of strength of Dsub(y)150 gate valve case, manufactured by centrifugal casting

International Nuclear Information System (INIS)

Umanskaya, L.G.; Semenov, P.V.; Tinyakov, V.G.; Babkina, R.I.; Khatuntsev, Eh.V.

1982-01-01

A process for manufacturing centrifugal-cast gate valve body is developed. Structural strength of such items, homogeneity, ductile and strength properties over the cross section as well as the metal susceptibility to embrittlement have been investigated. Three cast gate valve bodies have been taken: one - of 20GSL steel - for hydraulic testing, and two - of 15Kh1MFL steel - for investigation into the metal properties across the valve thickness. The strength properties of the centrifugal-cast gate valve body of 15Kh1M1FL steel are stated to meet the specifications. The gate valve metal ductility (delta and PSI) is twice as high as that of a sand-cast valve. The microstructure, strength and ductility are uniform both over wall thickness and over different body cross sections

Calculation of cracking under pulsed heat loads in tungsten manufactured according to ITER specifications

International Nuclear Information System (INIS)

Arakcheev, A.S.; Skovorodin, D.I.; Burdakov, A.V.; Shoshin, A.A.; Polosatkin, S.V.; Vasilyev, A.A.; Postupaev, V.V.; Vyacheslavov, L.N.; Kasatov, A.A.; Huber, A.; Mertens, Ph; Wirtz, M.; Linsmeier, Ch; Kreter, A.; Löwenhoff, Th; Begrambekov, L.; Grunin, A.; Sadovskiy, Ya

2015-01-01

A mathematical model of surface cracking under pulsed heat load was developed. The model correctly describes a smooth brittle–ductile transition. The elastic deformation is described in a thin-heated-layer approximation. The plastic deformation is described with the Hollomon equation. The time dependence of the deformation and stresses is described for one heating–cooling cycle for a material without initial plastic deformation. The model can be applied to tungsten manufactured according to ITER specifications. The model shows that the stability of stress-relieved tungsten deteriorates when the base temperature increases. This proved to be a result of the close ultimate tensile and yield strengths. For a heat load of arbitrary magnitude a stability criterion was obtained in the form of condition on the relation of the ultimate tensile and yield strengths.

Lexicon generation methods, lexicon generation devices, and lexicon generation articles of manufacture

Science.gov (United States)

Carter, Richard J [Richland, WA; McCall, Jonathon D [West Richland, WA; Whitney, Paul D [Richland, WA; Gregory, Michelle L [Richland, WA; Turner, Alan E [Kennewick, WA; Hetzler, Elizabeth G [Kennewick, WA; White, Amanda M [Kennewick, WA; Posse, Christian [Seattle, WA; Nakamura, Grant C [Kennewick, WA

2010-10-26

Lexicon generation methods, computer implemented lexicon editing methods, lexicon generation devices, lexicon editors, and articles of manufacture are described according to some aspects. In one aspect, a lexicon generation method includes providing a seed vector indicative of occurrences of a plurality of seed terms within a plurality of text items, providing a plurality of content vectors indicative of occurrences of respective ones of a plurality of content terms within the text items, comparing individual ones of the content vectors with respect to the seed vector, and responsive to the comparing, selecting at least one of the content terms as a term of a lexicon usable in sentiment analysis of text.

A Study on the Systematization of Classification Process for NSG Trigger List Items

Energy Technology Data Exchange (ETDEWEB)

Yang, Seunghyo; Tae, Jaewoong; Shin, Donghoon [Korea Institute of Nuclear Nonproliferation and Control/Nuclear Export Control Div., Daejeon (Korea, Republic of)

2013-05-15

In 1978, Nuclear Suppliers Group (NSG) was established to prevent nuclear items from being used for nuclear weapons. NSG drew up the NSG Guidelines (INFCIRC/254) that regulates export control items(so-called NSG trigger list items) and procedures. NSG recommends its member countries to reflect these guidelines on their export control systems and fulfill their obligations. Korea has carried out export controls on nuclear items by reflecting NSG Guidelines on Notice on Trade of Strategic Item of Foreign Trade Act since joining NSG in 1995. Nuclear export control starts with Classification that determines whether export items can be used for strategic items (goods and technologies that can be exclusively used for the manufacture, development and use of WMD). The standard of Classification is based on the NSG Guidelines. However, due to the qualitative characteristics of the Guidelines, there take place lots of difficulties in the Classification. Thus this study aims to suggest the systematic Classification process. Recently, the number of Classification requests is rapidly increasing due to the UAE commercial nuclear power plants and the Jordan reactors export. It is required to provide a more systematic Classification standard and process in order to provide an efficient and consistent Classification. Thus, this study analyzed limitations of EDP which causes difficulties in the process of classification due to its qualitative characteristics. Besides, it established systematic Classification process by quantitatively analyzing EDP. Consequently, it is expected that the results of this study will be used for as actual Classification. It still remains to establish a criterion of detailed information, which is one of the most important in the Classification for technology. Therefore, a further study will be conducted to establish a criterion of detailed information by analyzing Classification cases through the text mining techniques.

A Study on the Systematization of Classification Process for NSG Trigger List Items

International Nuclear Information System (INIS)

Yang, Seunghyo; Tae, Jaewoong; Shin, Donghoon

2013-01-01

In 1978, Nuclear Suppliers Group (NSG) was established to prevent nuclear items from being used for nuclear weapons. NSG drew up the NSG Guidelines (INFCIRC/254) that regulates export control items(so-called NSG trigger list items) and procedures. NSG recommends its member countries to reflect these guidelines on their export control systems and fulfill their obligations. Korea has carried out export controls on nuclear items by reflecting NSG Guidelines on Notice on Trade of Strategic Item of Foreign Trade Act since joining NSG in 1995. Nuclear export control starts with Classification that determines whether export items can be used for strategic items (goods and technologies that can be exclusively used for the manufacture, development and use of WMD). The standard of Classification is based on the NSG Guidelines. However, due to the qualitative characteristics of the Guidelines, there take place lots of difficulties in the Classification. Thus this study aims to suggest the systematic Classification process. Recently, the number of Classification requests is rapidly increasing due to the UAE commercial nuclear power plants and the Jordan reactors export. It is required to provide a more systematic Classification standard and process in order to provide an efficient and consistent Classification. Thus, this study analyzed limitations of EDP which causes difficulties in the process of classification due to its qualitative characteristics. Besides, it established systematic Classification process by quantitatively analyzing EDP. Consequently, it is expected that the results of this study will be used for as actual Classification. It still remains to establish a criterion of detailed information, which is one of the most important in the Classification for technology. Therefore, a further study will be conducted to establish a criterion of detailed information by analyzing Classification cases through the text mining techniques

Are computer numerical control (CNC)-manufactured patient-specific metal templates available for posterior thoracic pedicle screw insertion? Feasibility and accuracy evaluation.

Science.gov (United States)

Kong, Xiangxue; Tang, Lei; Ye, Qiang; Huang, Wenhua; Li, Jianyi

2017-11-01

Accurate and safe posterior thoracic pedicle insertion (PTPI) remains a challenge. Patient-specific drill templates (PDTs) created by rapid prototyping (RP) can assist in posterior thoracic pedicle insertion, but pose biocompatibility risks. The aims of this study were to develop alternative PDTs with computer numerical control (CNC) and assess their feasibility and accuracy in assisting PTPI. Preoperative CT images of 31 cadaveric thoracic vertebras were obtained and then the optimal pedicle screw trajectories were planned. The PDTs with optimal screw trajectories were randomly assigned to be designed and manufactured by CNC or RP in each vertebra. With the guide of the CNC- or RP-manufactured PDTs, the appropriate screws were inserted into the pedicles. Postoperative CT scans were performed to analyze any deviations at entry point and midpoint of the pedicles. The CNC group was found to be significant manufacture-time-shortening, and cost-decreasing, when compared with the RP group (P  0.05). The screw positions were grade 0 in 90.3% and grade 1 in 9.7% of the cases in the CNC group and grade 0 in 93.5% and grade 1 in 6.5% of the cases in the RP group (P = 0.641). CNC-manufactured PDTs are viable for assisting in PTPI with good feasibility and accuracy.

Review of technical specifications

International Nuclear Information System (INIS)

Bedrich, M.; Scholz, D.

1980-01-01

The present paper deals with position and function of technical specifications before and during the manufacturing of reactor components, their structure and reasons for specific regulations due to safety philosophy and explains the cooperation of supplier, manufacturer, utilities and supervisory organizations. (RW)

Laser additive manufacturing of high-performance materials

CERN Document Server

Gu, Dongdong

2015-01-01

This book entitled “Laser Additive Manufacturing of High-Performance Materials” covers the specific aspects of laser additive manufacturing of high-performance new materials components based on an unconventional materials incremental manufacturing philosophy, in terms of materials design and preparation, process control and optimization, and theories of physical and chemical metallurgy. This book describes the capabilities and characteristics of the development of new metallic materials components by laser additive manufacturing process, including nanostructured materials, in situ composite materials, particle reinforced metal matrix composites, etc. The topics presented in this book, similar as laser additive manufacturing technology itself, show a significant interdisciplinary feature, integrating laser technology, materials science, metallurgical engineering, and mechanical engineering. This is a book for researchers, students, practicing engineers, and manufacturing industry professionals interested i...

HISTORICAL PROCEDURES AND G-DSG METHOD BASED MANUFACTURING PLANNING

Institute of Scientific and Technical Information of China (English)

无

2000-01-01

Oriented to CAD/CAM seamless integration, this paper presents an idea for synthetically considering the qualitative history model, which represents the whole course of modeling, and the quantitative geometry model, which contains the extended Brep model, CSG and feature pedigree. History model building captures in background the dynamic interactive definition of engineering requirement and then explicitly conveys the original intention to successive application layers, which is conductive to the decision support of manufacturing planning in not only automatic geometry re-constructing but also machining set-up. G-DSG theory as an earlier achievement is applied to generate the topology-independent generalized mid-model as an input to manufacturing planning, which is therefore simplified and its accuracy is simultaneously improved. Manufacturing planning lays emphasis on optimizing the mapping in both geometry and function from part itself to detail machining scheme. Comparatively, process planning pays more attention to the mapping to those items like tool, fixture, etc. Theoretically, such an idea is also beneficial to realizing the parametric NC machining trajectory generation and maintaining its dynamic consistency with the update of the design model.

Storing empty calories and chronic disease risk: snack-food products, nutritive content, and manufacturers in Philadelphia corner stores.

Science.gov (United States)

Lucan, Sean C; Karpyn, Allison; Sherman, Sandy

2010-05-01

Corner stores are part of the urban food environment that may contribute to obesity and diet-related diseases, particularly for low-income and minority children. The snack foods available in corner stores may be a particularly important aspect of an urban child's food environment. Unfortunately, there is little data on exactly what snack foods corner stores stock, or where these foods come from. We evaluated snack foods in 17 Philadelphia corner stores, located in three ethnically distinct, low-income school neighborhoods. We recorded the manufacturer, calories, fat, sugar, and sodium for all snack items, excluding candy and prepared foods. We then compared the nutritive content of assessed snack items to established dietary recommendations and a school nutrition standard. In total, stores stocked 452 kinds of snacks, with only 15% of items common between all three neighborhoods. Total and unique snacks and snack food manufacturers varied by neighborhood, but distributions in snack type varied negligibly: overall, there were no fruit snacks, no vegetable snacks, and only 3.6% of all snacks (by liberal definition) were whole grain. The remainder (96.4% of snacks) was highly processed foods. Five of 65 manufacturers supplied 73.4% of all kinds of snack foods. Depending on serving size definition, 80.0-91.5% of snack foods were "unhealthy" (by the school nutrition standard), including seven of 11 wholegrain products. A single snack item could supply 6-14% of a day's recommended calories, fat, sugar, and sodium on average (or 56-169% at the extreme) for a "typical" child. We conclude that corner store snack food inventories are almost entirely unhealthful, and we discuss possible implications and next steps for research and intervention.

Audit Report The Procurement of Safety Class/Safety-Significant Items at the Savannah River Site

International Nuclear Information System (INIS)

2009-01-01

the Savannah River Site. Our review disclosed that the Department had procured and installed safety-class and safety-significant SSCs that did not meet NQA-1 quality standards. Specifically, we identified multiple instances in which critical components did not meet required quality and safety standards. For example: (1) Three structural components were procured and installed by the prime contractor at Savannah River during construction of the MOX Facility that did not meet the technical specifications for items relied on for safety. These substandard items necessitated costly and time consuming remedial action to, among other things, ensure that nonconforming materials and equipment would function within safety margins; (2) In six instances, items used in the construction of TEF failed to satisfy quality standards. In one of these situations, operating procedures had to be modified to ensure that the problem item did not compromise safety; and (3) Finally, at the ISP, one component that did not meet quality standards was procured. The failure of the item could have resulted in a spill of up to 15,000 gallons of high-level radioactive waste. Based on an extensive examination of relevant internal controls and procurement practices, we concluded that these failures were attributable to inadequate attention to quality assurance at Savannah River. Simply put, Departmental controls were not adequate to prevent and/or detect quality assurance problems. For example, Federal and prime contractor officials did not expressly require that subcontractors or lower-tiered vendors comply with quality assurance requirements. Additionally, management did not effectively communicate quality assurance concerns between the several Departmental program elements operating at Savannah River. The procurement and installation of these nonconforming components resulted in cost increases. For example, as of October 2008, the MOX Facility had incurred costs of more than $680,000 due to problems

Item Response Theory Analyses of the Cambridge Face Memory Test (CFMT)

Science.gov (United States)

Cho, Sun-Joo; Wilmer, Jeremy; Herzmann, Grit; McGugin, Rankin; Fiset, Daniel; Van Gulick, Ana E.; Ryan, Katie; Gauthier, Isabel

2014-01-01

We evaluated the psychometric properties of the Cambridge face memory test (CFMT; Duchaine & Nakayama, 2006). First, we assessed the dimensionality of the test with a bi-factor exploratory factor analysis (EFA). This EFA analysis revealed a general factor and three specific factors clustered by targets of CFMT. However, the three specific factors appeared to be minor factors that can be ignored. Second, we fit a unidimensional item response model. This item response model showed that the CFMT items could discriminate individuals at different ability levels and covered a wide range of the ability continuum. We found the CFMT to be particularly precise for a wide range of ability levels. Third, we implemented item response theory (IRT) differential item functioning (DIF) analyses for each gender group and two age groups (Age ≤ 20 versus Age > 21). This DIF analysis suggested little evidence of consequential differential functioning on the CFMT for these groups, supporting the use of the test to compare older to younger, or male to female, individuals. Fourth, we tested for a gender difference on the latent facial recognition ability with an explanatory item response model. We found a significant but small gender difference on the latent ability for face recognition, which was higher for women than men by 0.184, at age mean 23.2, controlling for linear and quadratic age effects. Finally, we discuss the practical considerations of the use of total scores versus IRT scale scores in applications of the CFMT. PMID:25642930

Redesigning Manufacturing Footprint from Dynamic Perspective

DEFF Research Database (Denmark)

Yang, Cheng; Farooq, Sami; Johansen, John

2009-01-01

footprint to address the constantly emerging new challenges by giving a holistic approach from dynamic perspective. Three Danish companies are presented. The way they developed their international manufacturing networks is analysed historically, and their redesigning of manufacturing footprint is expressed...... as how to re-assign portfolios of products and processes between specific plants within the same manufacturing network at one point in time. The strategic factors that have impact on such decisions are discussed and classified into two groups. Last, a holistic framework and a process model is presented...

Combining item and bulk material loss-detection uncertainties

International Nuclear Information System (INIS)

Eggers, R.F.

1982-01-01

Loss detection requirements, such as five formula kilograms with 99% probability of detection, which apply to the sum of losses from material in both item and bulk form, constitute a special problem for the nuclear material statistician. Requirements of this type are included in the Material Control and Accounting Reform Amendments described in the Advance Notice of Proposed Rule Making (Federal Register, 46(175):45144-46151). Attribute test sampling of items is the method used to detect gross defects in the inventory of items in a given control unit. Attribute sampling plans are designed to detect a loss of a specificed goal quantity of material with a given probability. In contrast to the methods and statistical models used for item loss detection, bulk material loss detection requires all the material entering and leaving a control unit to be measured and the calculation of a loss estimator that will be tested against an appropriate alarm threshold. The alarm threshold is determined from an estimate of the error inherent in the components of the loss estimator. In this paper a simple grahical method of evaluating the combined capabilities of bulk material loss detection methods and item attribute testing procedures will be described. Quantitative results will be given for several cases, indicating how a decrease in the precision of the item loss detection method tends to force an increase in the precision of the bulk loss detection procedure in order to meet the overall detection requirement. 4 figures

Development of Advanced Ceramic Manufacturing Technology; FINAL

International Nuclear Information System (INIS)

Pujari, V.K.

2001-01-01

Advanced structural ceramics are enabling materials for new transportation engine systems that have the potential for significantly reducing energy consumption and pollution in automobiles and heavy vehicles. Ceramic component reliability and performance have been demonstrated in previous U.S. DOE initiatives, but high manufacturing cost was recognized as a major barrier to commercialization. Norton Advanced Ceramics (NAC), a division of Saint-Gobain Industrial Ceramics, Inc. (SGIC), was selected to perform a major Advanced Ceramics Manufacturing Technology (ACMT) Program. The overall objectives of NAC's program were to design, develop, and demonstrate advanced manufacturing technology for the production of ceramic exhaust valves for diesel engines. The specific objectives were (1) to reduce the manufacturing cost by an order of magnitude, (2) to develop and demonstrate process capability and reproducibility, and (3) to validate ceramic valve performance, durability, and reliability. I n order to achieve these objectives, NAC, a leading U.S. advanced ceramics component manufacturer, assembled a multidisciplinary, vertically integrated team. This team included: a major diesel engine builder, Detroit Diesel Corporation (DDC); a corporate ceramics research division, SGIC's Northboro R and D Center; intelligent processing system developers, BDM Federal/MATSYS; a furnace equipment company, Centorr/Vacuum Industries; a sintering expert, Wittmer Consultants; a production OEM, Deco-Grand; a wheel manufacturer and grinding operation developer, Norton Company's Higgins Grinding Technology Center (HGTC); a ceramic machine shop, Chand Kare Technical Ceramics; and a manufacturing cost consultant, IBIS Associates. The program was divided into four major tasks: Component Design and Specification, Component Manufacturing Technology Development, Inspection and Testing, and Process Demonstration

Post Processing Methods used to Improve Surface Finish of Products which are Manufactured by Additive Manufacturing Technologies: A Review

Science.gov (United States)

Kumbhar, N. N.; Mulay, A. V.

2016-08-01

The Additive Manufacturing (AM) processes open the possibility to go directly from Computer-Aided Design (CAD) to a physical prototype. These prototypes are used as test models before it is finalized as well as sometimes as a final product. Additive Manufacturing has many advantages over the traditional process used to develop a product such as allowing early customer involvement in product development, complex shape generation and also save time as well as money. Additive manufacturing also possess some special challenges that are usually worth overcoming such as Poor Surface quality, Physical Properties and use of specific raw material for manufacturing. To improve the surface quality several attempts had been made by controlling various process parameters of Additive manufacturing and also applying different post processing techniques on components manufactured by Additive manufacturing. The main objective of this work is to document an extensive literature review in the general area of post processing techniques which are used in Additive manufacturing.

Random Item Generation Is Affected by Age

Science.gov (United States)

Multani, Namita; Rudzicz, Frank; Wong, Wing Yiu Stephanie; Namasivayam, Aravind Kumar; van Lieshout, Pascal

2016-01-01

Purpose: Random item generation (RIG) involves central executive functioning. Measuring aspects of random sequences can therefore provide a simple method to complement other tools for cognitive assessment. We examine the extent to which RIG relates to specific measures of cognitive function, and whether those measures can be estimated using RIG…

Differential item functioning magnitude and impact measures from item response theory models.

Science.gov (United States)

Kleinman, Marjorie; Teresi, Jeanne A

2016-01-01

Measures of magnitude and impact of differential item functioning (DIF) at the item and scale level, respectively are presented and reviewed in this paper. Most measures are based on item response theory models. Magnitude refers to item level effect sizes, whereas impact refers to differences between groups at the scale score level. Reviewed are magnitude measures based on group differences in the expected item scores and impact measures based on differences in the expected scale scores. The similarities among these indices are demonstrated. Various software packages are described that provide magnitude and impact measures, and new software presented that computes all of the available statistics conveniently in one program with explanations of their relationships to one another.

Additive-manufactured patient-specific titanium templates for thoracic pedicle screw placement: novel design with reduced contact area.

Science.gov (United States)

Takemoto, Mitsuru; Fujibayashi, Shunsuke; Ota, Eigo; Otsuki, Bungo; Kimura, Hiroaki; Sakamoto, Takeshi; Kawai, Toshiyuki; Futami, Tohru; Sasaki, Kiyoyuki; Matsushita, Tomiharu; Nakamura, Takashi; Neo, Masashi; Matsuda, Shuich

2016-06-01

Image-based navigational patient-specific templates (PSTs) for pedicle screw (PS) placement have been described. With recent advances in three-dimensional computer-aided designs and additive manufacturing technology, various PST designs have been reported, although the template designs were not optimized. We have developed a novel PST design that reduces the contact area without sacrificing stability. It avoids susceptibility to intervening soft tissue, template geometric inaccuracy, and difficulty during template fitting. Fourteen candidate locations on the posterior aspect of the vertebra were evaluated. Among them, locations that had high reproducibility on computed tomography (CT) images and facilitated accurate PS placement were selected for the final PST design. An additive manufacturing machine (EOSINT M270) fabricated the PSTs using commercially pure titanium powder. For the clinical study, 36 scoliosis patients and 4 patients with ossification of the posterior longitudinal ligament (OPLL) were treated with thoracic PSs using our newly developed PSTs. We intraoperatively and postoperatively evaluated the accuracy of the PS hole created by the PST. Based on the segmentation reproducibility and stability analyses, we selected seven small, round contact points for our PST: bilateral superior and inferior points on the transverse process base, bilateral inferior points on the laminar, and a superior point on the spinous process. Clinically, the success rates of PS placement using this PST design were 98.6 % (414/420) for scoliosis patients and 100 % (46/46) for OPLL patients. This study provides a useful design concept for the development and introduction of patient-specific navigational templates for placing PSs.

ITEM LEVEL DIAGNOSTICS AND MODEL - DATA FIT IN ITEM ...

African Journals Online (AJOL)

Global Journal

Item response theory (IRT) is a framework for modeling and analyzing item response ... data. Though, there is an argument that the evaluation of fit in IRT modeling has been ... National Council on Measurement in Education ... model data fit should be based on three types of ... prediction should be assessed through the.

Secondary Psychometric Examination of the Dimensional Obsessive-Compulsive Scale: Classical Testing, Item Response Theory, and Differential Item Functioning.

Science.gov (United States)

Thibodeau, Michel A; Leonard, Rachel C; Abramowitz, Jonathan S; Riemann, Bradley C

2015-12-01

The Dimensional Obsessive-Compulsive Scale (DOCS) is a promising measure of obsessive-compulsive disorder (OCD) symptoms but has received minimal psychometric attention. We evaluated the utility and reliability of DOCS scores. The study included 832 students and 300 patients with OCD. Confirmatory factor analysis supported the originally proposed four-factor structure. DOCS total and subscale scores exhibited good to excellent internal consistency in both samples (α = .82 to α = .96). Patient DOCS total scores reduced substantially during treatment (t = 16.01, d = 1.02). DOCS total scores discriminated between students and patients (sensitivity = 0.76, 1 - specificity = 0.23). The measure did not exhibit gender-based differential item functioning as tested by Mantel-Haenszel chi-square tests. Expected response options for each item were plotted as a function of item response theory and demonstrated that DOCS scores incrementally discriminate OCD symptoms ranging from low to extremely high severity. Incremental differences in DOCS scores appear to represent unbiased and reliable differences in true OCD symptom severity. © The Author(s) 2014.

49 CFR 178.33a-6 - Manufacture.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Manufacture. 178.33a-6 Section 178.33a-6 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY... Specifications for Inside Containers, and Linings § 178.33a-6 Manufacture. (a) By appliances and methods that...

49 CFR 178.33b-6 - Manufacture.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Manufacture. 178.33b-6 Section 178.33b-6 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY... Specifications for Inside Containers, and Linings § 178.33b-6 Manufacture. (a) Each container must be...

An eoq model for weibull deteriorating item with ramp type demand and salvage value under trade credit system

Directory of Open Access Journals (Sweden)

Lalit Mohan Pradhan

2014-03-01

Full Text Available Background: In the present competitive business scenario researchers have developed various inventory models for deteriorating items considering various practical situations for better inventory control. Permissible delay in payments with various demands and deteriorations is considerably a new concept introduced in developing various inventory models. These models are very useful for both the consumers and the manufacturer. Methods: In the present work an inventory model has been developed for a three parameter Weibull deteriorating item with ramp type demand and salvage value under trade credit system. Here we have considered a single item for developing the model. Results and conclusion: Optimal order quantity, optimal cycle time and total variable cost during a cycle have been derived for the proposed inventory model. The results obtained in this paper have been illustrated with the help of numerical examples and sensitivity analysis.   

Development of Advanced Ceramic Manufacturing Technology

Energy Technology Data Exchange (ETDEWEB)

Pujari, V.K.

2001-04-05

Advanced structural ceramics are enabling materials for new transportation engine systems that have the potential for significantly reducing energy consumption and pollution in automobiles and heavy vehicles. Ceramic component reliability and performance have been demonstrated in previous U.S. DOE initiatives, but high manufacturing cost was recognized as a major barrier to commercialization. Norton Advanced Ceramics (NAC), a division of Saint-Gobain Industrial Ceramics, Inc. (SGIC), was selected to perform a major Advanced Ceramics Manufacturing Technology (ACMT) Program. The overall objectives of NAC's program were to design, develop, and demonstrate advanced manufacturing technology for the production of ceramic exhaust valves for diesel engines. The specific objectives were (1) to reduce the manufacturing cost by an order of magnitude, (2) to develop and demonstrate process capability and reproducibility, and (3) to validate ceramic valve performance, durability, and reliability. The program was divided into four major tasks: Component Design and Specification, Component Manufacturing Technology Development, Inspection and Testing, and Process Demonstration. A high-power diesel engine valve for the DDC Series 149 engine was chosen as the demonstration part for this program. This was determined to be an ideal component type to demonstrate cost-effective process enhancements, the beneficial impact of advanced ceramics on transportation systems, and near-term commercialization potential. The baseline valve material was NAC's NT451 SiAION. It was replaced, later in the program, by an alternate silicon nitride composition (NT551), which utilized a lower cost raw material and a simplified powder-processing approach. The material specifications were defined based on DDC's engine requirements, and the initial and final component design tasks were completed.

Park Facilities, Boundaries were determined from parcel mapping lines & site specific items, such as shelter locations, were obtained by field GPS observation, Published in 2010, Not Applicable scale, Chippewa County Government.

Data.gov (United States)

NSGIC Local Govt | GIS Inventory — Park Facilities dataset current as of 2010. Boundaries were determined from parcel mapping lines & site specific items, such as shelter locations, were obtained...

ASPIE: A Framework for Active Sensing and Processing of Complex Events in the Internet of Manufacturing Things

Directory of Open Access Journals (Sweden)

Shaobo Li

2018-03-01

Full Text Available Rapid perception and processing of critical monitoring events are essential to ensure healthy operation of Internet of Manufacturing Things (IoMT-based manufacturing processes. In this paper, we proposed a framework (active sensing and processing architecture (ASPIE for active sensing and processing of critical events in IoMT-based manufacturing based on the characteristics of IoMT architecture as well as its perception model. A relation model of complex events in manufacturing processes, together with related operators and unified XML-based semantic definitions, are developed to effectively process the complex event big data. A template based processing method for complex events is further introduced to conduct complex event matching using the Apriori frequent item mining algorithm. To evaluate the proposed models and methods, we developed a software platform based on ASPIE for a local chili sauce manufacturing company, which demonstrated the feasibility and effectiveness of the proposed methods for active perception and processing of complex events in IoMT-based manufacturing.

Mediate gamma radiation effects on some packaged food items

International Nuclear Information System (INIS)

Inamura, Patricia Y.; Uehara, Vanessa B.; Teixeira, Christian A.H.M.; Mastro, Nelida L. del

2012-01-01

For most of prepackaged foods a 10 kGy radiation dose is considered the maximum dose needed; however, the commercially available and practically accepted packaging materials must be suitable for such application. This work describes the application of ionizing radiation on several packaged food items, using 5 dehydrated food items, 5 ready-to-eat meals and 5 ready-to-eat food items irradiated in a 60 Co gamma source with a 3 kGy dose. The quality evaluation of the irradiated samples was performed 2 and 8 months after irradiation. Microbiological analysis (bacteria, fungus and yeast load) was performed. The sensory characteristics were established for appearance, aroma, texture and flavor attributes were also established. From these data, the acceptability of all irradiated items was obtained. All ready-to-eat food items assayed like manioc flour, some pâtés and blocks of raw brown sugar and most of ready-to-eat meals like sausages and chicken with legumes were considered acceptable for microbial and sensory characteristics. On the other hand, the dehydrated food items chosen for this study, such as dehydrated bacon potatoes or pea soups were not accepted by the sensory analysis. A careful dose choice and special irradiation conditions must be used in order to achieve sensory acceptability needed for the commercialization of specific irradiated food items. - Highlights: ► We applied gamma radiation on several kinds of packaged food items. ► Microbiological and sensory analyses were performed 2 and 8 months after irradiation. ► All ready-to-eat food items assayed were approved for microbial and sensory characteristics. ► Most ready-to-eat meals like sausages and chicken with legumes were also acceptable. ► Dehydrated bacon potatoes or pea soups were considered not acceptable.

Overview of the Photovoltaic Manufacturing Technology (PVMaT) project

International Nuclear Information System (INIS)

Witt, C.E.; Mitchell, R.L.; Mooney, G.D.

1993-08-01

The Photovoltaic Manufacturing Technology (PVMaT) project is a historic government/industry photovoltaic (PV) manufacturing R ampersand D partnership composed of joint efforts between the federal government (through the US Department of Energy) and members of the US PV industry. The project's ultimate goal is to ensure that the US industry retains and extends its world leadership role in the manufacture and commercial development of PV components and systems. PVMaT is designed to do this by helping the US PV industry improve manufacturing processes, accelerate manufacturing cost reductions for PV modules, improve commercial product performance, and lay the groundwork for a substantial scale-up of US-based PV manufacturing capacities. Phase 1 of the project, the problem identification phase, was completed in early 1991. Phase 2, the problem solution phase, which addresses process-specific problems of specific manufacturers, is now underway with an expected duration of 5 years. Phase 3 addresses R ampersand D problems that are relatively common to a number of PV companies or the PV industry as a whole. These ''generic'' problem areas are being addressed through a teamed research approach

Gender Differences in Figural Matrices: The Moderating Role of Item Design Features

Science.gov (United States)

Arendasy, Martin E.; Sommer, Markus

2012-01-01

There is a heated debate on whether observed gender differences in some figural matrices in adults can be attributed to gender differences in inductive reasoning/G[subscript f] or differential item functioning and/or test bias. Based on previous studies we hypothesized that three specific item design features moderate the effect size of the gender…

Easy and Informative: Using Confidence-Weighted True-False Items for Knowledge Tests in Psychology Courses

Science.gov (United States)

Dutke, Stephan; Barenberg, Jonathan

2015-01-01

We introduce a specific type of item for knowledge tests, confidence-weighted true-false (CTF) items, and review experiences of its application in psychology courses. A CTF item is a statement about the learning content to which students respond whether the statement is true or false, and they rate their confidence level. Previous studies using…

Manufacture of a heat-resistant alloy with modified specifications for HTGR structural applications

International Nuclear Information System (INIS)

Sahira, K.; Kondo, T.; Takeiri, T.

1984-01-01

A method of manufacturing a nuclear grade nickel-base heat-resistant alloy in application to heliumcooled reactor primary circuit components has been developed. The Hastelloy-XR alloy, a version of Hastelloy-X, was made available by combining the basic studies of the oxidation behavior of Hastelloy-X and the improvement of manufacturing techniques. In the primary and remelting steps, the choice of appropriate processes was made by performing numerical analyses of the statistical deviation of both chemical composition and the products' mechanical properties. The feasibility of making larger electroslag remelting ingots with reasonable control of macrosegregation was examined by the calculation of a molten metal pool shape during melting. The hot workability of Hastelloy-XR was confirmed to be equivalent to that of Hastelloy-X and the importance of controlling the thermal and mechanical processes more closely was stressed in obtaining a higher level of quality assurance for the nuclear applications. The possibility of enhancing the high-temperature mechanical performance of Hastelloy-XR was suggested based on the preliminary test results with the heats manufactured with controlled boron content

An Analysis of Item Identification for Additive Manufacturing (3-D Printing) Within the Naval Supply Chain

Science.gov (United States)

2014-12-01

microparts Datar, S . M., Horngren , C. T., & Rajan, M. (2012). Cost accounting : A managerial emphasis. Upper Saddle River, NJ: Pearson Prentice Hall... Horngren , and Rajan (2012) infer that common decision criteria for managers include quality, dependability of suppliers, and costs as the most...IDENTIFICATION FOR ADDITIVE MANUFACTURING (3-D PRINTING) WITHIN THE NAVAL SUPPLY CHAIN 5. FUNDING NUMBERS 6. AUTHOR( S ) Jason A. Morgan, Jacob M

Exploring the Pattern of Internal Communication in Total Quality Management Implementation in Manufacturing Companies

Directory of Open Access Journals (Sweden)

Samsudin Sharina

2017-01-01

Full Text Available Communication is an important aspect of organizational dynamic process and it is irrefutable one of the critical success factors of the Total Quality Management (TQM implementation. Although there are increasing awareness concerning the importance of internal organizational communication, knowledge appears to have rarely translated into practice or there is lack of guidance to effectively practicing it. Therefore, a study was proposed to investigate the pattern of internal communication practice in TQM implementation. This paper concerns on focusing into internal communication practices in TQM implementation factors and the communication patterns in terms of message forms and mediums of communication to convey TQM messages. Reliability and Factor analysis were carried out to confirm items that form each factor in internal communication in TQM implementation. Based on the analysis of survey questionnaires distributed to 104 large manufacturing companies implementing TQM in Malaysia, it was found that there are certain communication patterns practice by the management when conveying and disseminating TQM messages, but they have no specific guidelines. Therefore, the internal communication practices are not well planned. Finally, it is suggested that further research should be carried out to explain clearly the role and strategy of communication on this issue in order to boost the success of TQM implementation particularly in manufacturing company.

Influence of Manufacturing Processes on the Performance of Phantom Lungs

International Nuclear Information System (INIS)

Traub, Richard J.

2008-01-01

Chest counting is an important tool for estimating the radiation dose to individuals who have inhaled radioactive materials. Chest counting systems are calibrated by counting the activity in the lungs of phantoms where the activity in the phantom lungs is known. In the United States a commonly used calibration phantom was developed at the Lawrence Livermore National Laboratory and is referred to as the Livermore Torso Phantom. An important feature of this phantom is that the phantom lungs can be interchanged so that the counting system can be challenged by different combinations of radionuclides and activity. Phantom lungs are made from lung tissue substitutes whose constituents are foaming plastics and various adjuvants selected to make the lung tissue substitute similar to normal healthy lung tissue. Some of the properties of phantom lungs cannot be readily controlled by phantom lung manufacturers. Some, such as density, are a complex function of the manufacturing process, while others, such as elemental composition of the bulk plastic are controlled by the plastics manufacturer without input, or knowledge of the phantom manufacturer. Despite the fact that some of these items cannot be controlled, they can be measured and accounted for. This report describes how manufacturing processes can influence the performance of phantom lungs. It is proposed that a metric that describes the brightness of the lung be employed by the phantom lung manufacturer to determine how well the phantom lung approximates the characteristics of a human lung. For many purposes, the linear attenuation of the lung tissue substitute is an appropriate surrogate for the brightness

A 67-Item Stress Resilience item bank showing high content validity was developed in a psychosomatic sample.

Science.gov (United States)

Obbarius, Nina; Fischer, Felix; Obbarius, Alexander; Nolte, Sandra; Liegl, Gregor; Rose, Matthias

2018-04-10

To develop the first item bank to measure Stress Resilience (SR) in clinical populations. Qualitative item development resulted in an initial pool of 131 items covering a broad theoretical SR concept. These items were tested in n=521 patients at a psychosomatic outpatient clinic. Exploratory and Confirmatory Factor Analysis (CFA), as well as other state-of-the-art item analyses and IRT were used for item evaluation and calibration of the final item bank. Out of the initial item pool of 131 items, we excluded 64 items (54 factor loading .3, 2 non-discriminative Item Response Curves, 4 Differential Item Functioning). The final set of 67 items indicated sufficient model fit in CFA and IRT analyses. Additionally, a 10-item short form with high measurement precision (SE≤.32 in a theta range between -1.8 and +1.5) was derived. Both the SR item bank and the SR short form were highly correlated with an existing static legacy tool (Connor-Davidson Resilience Scale). The final SR item bank and 10-item short form showed good psychometric properties. When further validated, they will be ready to be used within a framework of Computer-Adaptive Tests for a comprehensive assessment of the Stress-Construct. Copyright © 2018. Published by Elsevier Inc.

Good manufacturing practice - quality assurance programs

International Nuclear Information System (INIS)

Masefield, John; Thompson, Steven

1986-01-01

The concept of good manufacturing practice (GMP) in the medical device industry requires the use of controlled methods and equipment in performing each step in the device manufacturing process. Quality assurance programs are used to maintain compliance with GMP requirements by prescribing the operating and control procedures to be used. The specific elements of a quality assurance program for the radiation sterilization of medical devices are described. (author)

Teoria da Resposta ao Item Teoria de la respuesta al item Item response theory

Directory of Open Access Journals (Sweden)

Eutalia Aparecida Candido de Araujo

2009-12-01

Full Text Available A preocupação com medidas de traços psicológicos é antiga, sendo que muitos estudos e propostas de métodos foram desenvolvidos no sentido de alcançar este objetivo. Entre os trabalhos propostos, destaca-se a Teoria da Resposta ao Item (TRI que, a princípio, veio completar limitações da Teoria Clássica de Medidas, empregada em larga escala até hoje na medida de traços psicológicos. O ponto principal da TRI é que ela leva em consideração o item particularmente, sem relevar os escores totais; portanto, as conclusões não dependem apenas do teste ou questionário, mas de cada item que o compõe. Este artigo propõe-se a apresentar esta Teoria que revolucionou a teoria de medidas.La preocupación con las medidas de los rasgos psicológicos es antigua y muchos estudios y propuestas de métodos fueron desarrollados para lograr este objetivo. Entre estas propuestas de trabajo se incluye la Teoría de la Respuesta al Ítem (TRI que, en principio, vino a completar las limitaciones de la Teoría Clásica de los Tests, ampliamente utilizada hasta hoy en la medida de los rasgos psicológicos. El punto principal de la TRI es que se tiene en cuenta el punto concreto, sin relevar las puntuaciones totales; por lo tanto, los resultados no sólo dependen de la prueba o cuestionario, sino que de cada ítem que lo compone. En este artículo se propone presentar la Teoría que revolucionó la teoría de medidas.The concern with measures of psychological traits is old and many studies and proposals of methods were developed to achieve this goal. Among these proposed methods highlights the Item Response Theory (IRT that, in principle, came to complete limitations of the Classical Test Theory, which is widely used until nowadays in the measurement of psychological traits. The main point of IRT is that it takes into account the item in particular, not relieving the total scores; therefore, the findings do not only depend on the test or questionnaire

Serum Neuron-Specific Enolase, Biogenic Amino-Acids and Neurobehavioral Function in Lead-Exposed Workers from Lead-Acid Battery Manufacturing Process

OpenAIRE

K Ravibabu; T Barman; HR Rajmohan

2015-01-01

Background: The interaction between serum neuron-specific enolase (NSE), biogenic amino-acids and neurobehavioral function with blood lead levels in workers exposed to lead form lead-acid battery manufacturing process was not studied. Objective: To evaluate serum NSE and biogenic amino-acids (dopamine and serotonin) levels, and neurobehavioral performance among workers exposed to lead from lead-acid storage battery plant, and its relation with blood lead levels (BLLs). Methods: In a c...

Test manufacture of a canister insert

International Nuclear Information System (INIS)

Raiko, H.

2004-11-01

This report describes the insert-manufacturing test of a disposal canister for spent nuclear fuel that was made by Metso Paper Oy, Jyvaeskylae Foundry, in 2003 on contract for Posiva Oy. The test manufacture was a part of the co-operation development programme of encapsulation technology between SKB AB and Posiva Oy. Insert casting was specified according to the current manufacturing specifications of SKB. The canister insert was of BWR-type with integral bottom. This was the first trial manufacture of this type of insert in Finland and, in total, the second test manufacture of insert by Metso Paper. The result fulfilled all the requirements but the material mechanical properties and metallurgical structure of the cast material. The measured tensile strength, ultimate strength and elongation at rupture were lower than specified. The reason for this was revealed in the metallurgical investigation of the cast material. The nodulizing of the graphite was not occurred during the casting process according to the requirements. (orig.)

Item response theory analysis of the Pain Self-Efficacy Questionnaire.

Science.gov (United States)

Costa, Daniel S J; Asghari, Ali; Nicholas, Michael K

2017-01-01

The Pain Self-Efficacy Questionnaire (PSEQ) is a 10-item instrument designed to assess the extent to which a person in pain believes s/he is able to accomplish various activities despite their pain. There is strong evidence for the validity and reliability of both the full-length PSEQ and a 2-item version. The purpose of this study is to further examine the properties of the PSEQ using an item response theory (IRT) approach. We used the two-parameter graded response model to examine the category probability curves, and location and discrimination parameters of the 10 PSEQ items. In item response theory, responses to a set of items are assumed to be probabilistically determined by a latent (unobserved) variable. In the graded-response model specifically, item response threshold (the value of the latent variable for which adjacent response categories are equally likely) and discrimination parameters are estimated for each item. Participants were 1511 mixed, chronic pain patients attending for initial assessment at a tertiary pain management centre. All items except item 7 ('I can cope with my pain without medication') performed well in IRT analysis, and the category probability curves suggested that participants used the 7-point response scale consistently. Items 6 ('I can still do many of the things I enjoy doing, such as hobbies or leisure activity, despite pain'), 8 ('I can still accomplish most of my goals in life, despite the pain') and 9 ('I can live a normal lifestyle, despite the pain') captured higher levels of the latent variable with greater precision. The results from this IRT analysis add to the body of evidence based on classical test theory illustrating the strong psychometric properties of the PSEQ. Despite the relatively poor performance of Item 7, its clinical utility warrants its retention in the questionnaire. The strong psychometric properties of the PSEQ support its use as an effective tool for assessing self-efficacy in people with pain

Assessing location attractiveness for manufacturing automobiles

Energy Technology Data Exchange (ETDEWEB)

Hanawalt, Edward; Rouse, William

2017-07-01

Evaluating country manufacturing location attractiveness on various performance measures deepens the analysis and provides a more informed basis for manufacturing site selection versus reliance on labor rates alone. A short list of countries can be used to drive regional considerations for site-specific selection within a country. Design/methodology/approach: The two-step multi attribute decision model contains an initial filter layer to require minimum values for low weighted attributes and provides a rank order utility score for twenty three countries studied. The model contains 11 key explanatory variables with Labor Rate, Material Cost, and Logistics making up the top 3 attributes and representing 54% percent of the model weights. Findings: We propose a multi attribute decision framework for strategically assessing the attractiveness of a country as a location for manufacturing automobiles. Research limitations/implications: Consideration of country level wage variation, specific tariffs, and other economic incentives provides a secondary analysis after the initial list of candidate countries is defined. Practical implications: The results of our modeling shows China, India, and Mexico are currently the top ranked countries for manufacturing attractiveness. These three markets hold the highest utility scores throughout sensitivity analysis on the labor rate attribute weight rating, highlighting the strength and potential of manufacturing in China, India, and Mexico. Originality/value: Combining MAUT with regression analysis to simplify model to core factors then using a “must have” layer to handle extreme impacts of low weight factors and allowing for ease of repeatability.

Assessing location attractiveness for manufacturing automobiles

International Nuclear Information System (INIS)

Hanawalt, Edward; Rouse, William

2017-01-01

Evaluating country manufacturing location attractiveness on various performance measures deepens the analysis and provides a more informed basis for manufacturing site selection versus reliance on labor rates alone. A short list of countries can be used to drive regional considerations for site-specific selection within a country. Design/methodology/approach: The two-step multi attribute decision model contains an initial filter layer to require minimum values for low weighted attributes and provides a rank order utility score for twenty three countries studied. The model contains 11 key explanatory variables with Labor Rate, Material Cost, and Logistics making up the top 3 attributes and representing 54% percent of the model weights. Findings: We propose a multi attribute decision framework for strategically assessing the attractiveness of a country as a location for manufacturing automobiles. Research limitations/implications: Consideration of country level wage variation, specific tariffs, and other economic incentives provides a secondary analysis after the initial list of candidate countries is defined. Practical implications: The results of our modeling shows China, India, and Mexico are currently the top ranked countries for manufacturing attractiveness. These three markets hold the highest utility scores throughout sensitivity analysis on the labor rate attribute weight rating, highlighting the strength and potential of manufacturing in China, India, and Mexico. Originality/value: Combining MAUT with regression analysis to simplify model to core factors then using a “must have” layer to handle extreme impacts of low weight factors and allowing for ease of repeatability.

Control systems engineering in continuous pharmaceutical manufacturing. May 20-21, 2014 Continuous Manufacturing Symposium.

Science.gov (United States)

Myerson, Allan S; Krumme, Markus; Nasr, Moheb; Thomas, Hayden; Braatz, Richard D

2015-03-01

This white paper provides a perspective of the challenges, research needs, and future directions for control systems engineering in continuous pharmaceutical processing. The main motivation for writing this paper is to facilitate the development and deployment of control systems technologies so as to ensure quality of the drug product. Although the main focus is on small-molecule pharmaceutical products, most of the same statements apply to biological drug products. An introduction to continuous manufacturing and control systems is followed by a discussion of the current status and technical needs in process monitoring and control, systems integration, and risk analysis. Some key points are that: (1) the desired objective in continuous manufacturing should be the satisfaction of all critical quality attributes (CQAs), not for all variables to operate at steady-state values; (2) the design of start-up and shutdown procedures can significantly affect the economic operation of a continuous manufacturing process; (3) the traceability of material as it moves through the manufacturing facility is an important consideration that can at least in part be addressed using residence time distributions; and (4) the control systems technologies must assure quality in the presence of disturbances, dynamics, uncertainties, nonlinearities, and constraints. Direct measurement, first-principles and empirical model-based predictions, and design space approaches are described for ensuring that CQA specifications are met. Ways are discussed for universities, regulatory bodies, and industry to facilitate working around or through barriers to the development of control systems engineering technologies for continuous drug manufacturing. Industry and regulatory bodies should work with federal agencies to create federal funding mechanisms to attract faculty to this area. Universities should hire faculty interested in developing first-principles models and control systems technologies for

The Sustainability Cone - A holistic framework to integrate sustainability thinking into manufacturing

DEFF Research Database (Denmark)

Rödger, Jan-Markus; Bey, Niki; Alting, Leo

2016-01-01

Integrating sustainability into manufacturing is a multifaceted endeavour. Global sustainability aspects and specific manufacturing success factors have to be combined with life cycle thinking in order to get the holistic view on manufacturing which is needed to make truly sustainability-oriented......Integrating sustainability into manufacturing is a multifaceted endeavour. Global sustainability aspects and specific manufacturing success factors have to be combined with life cycle thinking in order to get the holistic view on manufacturing which is needed to make truly sustainability...... - as the missing link which closes these gaps by providing necessary holistic and consistent overview while being aligned with established stage-gate project execution models, thus ensuring practical applicability as shown for a highly automated production cell. The paper shows how to apply life cycle target...

Manufacturing Technology Information Analysis Center: Knowledge Is Strength

Science.gov (United States)

Safar, Michal

1992-01-01

The Center's primary function is to facilitate technology transfer within DoD, other government agencies and industry. The DoD has recognized the importance of technology transfer, not only to support specific weapon system manufacture, but to strengthen the industrial base that sustains DoD. MTIAC uses an experienced technical staff of engineers and information specialists to acquire, analyze, and disseminate technical information. Besides ManTech project data, MTIAC collects manufacturing technology from other government agencies, commercial publications, proceedings, and various international sources. MTIAC has various means of disseminating this information. Much of the technical data is on user accessible data bases. The Center researches and writes a number of technical reports each year and publishes a newsletter monthly. Customized research is performed in response to specific inquiries from government and industry. MTIAC serves as a link between Government and Industry to strengthen the manufacturing technology base through the dissemination of advanced manufacturing information.

A photographic method to measure food item intake. Validation in geriatric institutions.

Science.gov (United States)

Pouyet, Virginie; Cuvelier, Gérard; Benattar, Linda; Giboreau, Agnès

2015-01-01

From both a clinical and research perspective, measuring food intake is an important issue in geriatric institutions. However, weighing food in this context can be complex, particularly when the items remaining on a plate (side dish, meat or fish and sauce) need to be weighed separately following consumption. A method based on photography that involves taking photographs after a meal to determine food intake consequently seems to be a good alternative. This method enables the storage of raw data so that unhurried analyses can be performed to distinguish the food items present in the images. Therefore, the aim of this paper was to validate a photographic method to measure food intake in terms of differentiating food item intake in the context of a geriatric institution. Sixty-six elderly residents took part in this study, which was performed in four French nursing homes. Four dishes of standardized portions were offered to the residents during 16 different lunchtimes. Three non-trained assessors then independently estimated both the total and specific food item intakes of the participants using images of their plates taken after the meal (photographic method) and a reference image of one plate taken before the meal. Total food intakes were also recorded by weighing the food. To test the reliability of the photographic method, agreements between different assessors and agreements among various estimates made by the same assessor were evaluated. To test the accuracy and specificity of this method, food intake estimates for the four dishes were compared with the food intakes determined using the weighed food method. To illustrate the added value of the photographic method, food consumption differences between the dishes were explained by investigating the intakes of specific food items. Although they were not specifically trained for this purpose, the results demonstrated that the assessor estimates agreed between assessors and among various estimates made by the same

Inventory model with two rates of production for deteriorating items with permissible delay in payments

Science.gov (United States)

Roy, Ajanta; Samanta, G. P.

2011-08-01

Goyal (1985) ['Economic Order Quantity Under Conditions of Permissible Delay in Payments', Journal of Operational research Society, 36, 35-38] assumed that unit selling price and unit purchasing price are equal. But in real-life the scenario is different. The purpose of this article is to reflect the real life problem by allowing unit selling price and purchasing price to be unequal. Our model is a continuous production control inventory model for deteriorating items in which two different rates of production are available. The results are illustrated with the help of a numerical example. We discuss the sensitivity of the solution together with the changes of the values of the parameters associated with the model. Our model may be applicable in many manufacturing planning situations where management practices for deterioration are stringent; e.g. the two-production rate will be more profitable than the one-production rate in the manufacture of cold, asthma and allergy medicine. Our proposed model might be applicable to develop a prototype advance planning system for those manufacturers to integrate the management science techniques into commercial planning.

Computerized Adaptive Test (CAT) Applications and Item Response Theory Models for Polytomous Items

Science.gov (United States)

Aybek, Eren Can; Demirtasli, R. Nukhet

2017-01-01

This article aims to provide a theoretical framework for computerized adaptive tests (CAT) and item response theory models for polytomous items. Besides that, it aims to introduce the simulation and live CAT software to the related researchers. Computerized adaptive test algorithm, assumptions of item response theory models, nominal response…

Differential item functioning analysis of the Vanderbilt Expertise Test for cars.

Science.gov (United States)

Lee, Woo-Yeol; Cho, Sun-Joo; McGugin, Rankin W; Van Gulick, Ana Beth; Gauthier, Isabel

2015-01-01

The Vanderbilt Expertise Test for cars (VETcar) is a test of visual learning for contemporary car models. We used item response theory to assess the VETcar and in particular used differential item functioning (DIF) analysis to ask if the test functions the same way in laboratory versus online settings and for different groups based on age and gender. An exploratory factor analysis found evidence of multidimensionality in the VETcar, although a single dimension was deemed sufficient to capture the recognition ability measured by the test. We selected a unidimensional three-parameter logistic item response model to examine item characteristics and subject abilities. The VETcar had satisfactory internal consistency. A substantial number of items showed DIF at a medium effect size for test setting and for age group, whereas gender DIF was negligible. Because online subjects were on average older than those tested in the lab, we focused on the age groups to conduct a multigroup item response theory analysis. This revealed that most items on the test favored the younger group. DIF could be more the rule than the exception when measuring performance with familiar object categories, therefore posing a challenge for the measurement of either domain-general visual abilities or category-specific knowledge.

Language-related differential item functioning between English and German PROMIS Depression items is negligible.

Science.gov (United States)

Fischer, H Felix; Wahl, Inka; Nolte, Sandra; Liegl, Gregor; Brähler, Elmar; Löwe, Bernd; Rose, Matthias

2017-12-01

To investigate differential item functioning (DIF) of PROMIS Depression items between US and German samples we compared data from the US PROMIS calibration sample (n = 780), a German general population survey (n = 2,500) and a German clinical sample (n = 621). DIF was assessed in an ordinal logistic regression framework, with 0.02 as criterion for R 2 -change and 0.096 for Raju's non-compensatory DIF. Item parameters were initially fixed to the PROMIS Depression metric; we used plausible values to account for uncertainty in depression estimates. Only four items showed DIF. Accounting for DIF led to negligible effects for the full item bank as well as a post hoc simulated computer-adaptive test (German general population sample was considerably lower compared to the US reference value of 50. Overall, we found little evidence for language DIF between US and German samples, which could be addressed by either replacing the DIF items by items not showing DIF or by scoring the short form in German samples with the corrected item parameters reported. Copyright © 2016 John Wiley & Sons, Ltd.

Loss and Gain in Translation of Culture-Specific Items in Ahmad Tohari’s Lintang Kemukus from Indonesian Into English: A Semantic Study

Directory of Open Access Journals (Sweden)

Leni Tiwiyanti

2017-05-01

Full Text Available Culture-specific items (CSIs are difficult to translate since they are related to cultural knowledge and cultural background of the given culture. The distance and differences between two different cultures determine the extent of the gain or loss that will be exprienced by the CSIs as they are translated. The purposes of this research were to identify the translation procedures applied in translating CSIs which caused loss and gained in the translation process and to identify how the translator compensated the loss in translating CSIs. The method used was qualitative descriptive method. The result shows that loss is more prevalent than gain although the translator has enough knowledge on the source text culture as he has spent some years doing some researches in Banyumas society. There are two kinds of losses found in this study; inevitable and avertable losses. Translation procedures used which result in loss in translation are translation by a more general word (subordinate, translation by a more neutral/less expressive word and translation by cultural substitution. Gain was realized mostly through the creativity of the translator when they are able to explain the culture-specific items for effective communication. In order to compensate the loss that might have occurred, translator uses some translation procedures. They are translation by loan word with explanation, translation by paraphrase using related word, and translation by paraphrase using unrelated word. In short, gain in translation for better communication is not easy to achieve especially in the case of translating CSIs.

Problem specific heuristics for group scheduling problems in cellular manufacturing

OpenAIRE

Neufeld, Janis Sebastian

2016-01-01

The group scheduling problem commonly arises in cellular manufacturing systems, where parts are grouped into part families. It is characterized by a sequencing task on two levels: on the one hand, a sequence of jobs within each part family has to be identified while, on the other hand, a family sequence has to be determined. In order to solve this NP-hard problem usually heuristic solution approaches are used. In this thesis different aspects of group scheduling are discussed and problem spec...

Selecting Items for Criterion-Referenced Tests.

Science.gov (United States)

Mellenbergh, Gideon J.; van der Linden, Wim J.

1982-01-01

Three item selection methods for criterion-referenced tests are examined: the classical theory of item difficulty and item-test correlation; the latent trait theory of item characteristic curves; and a decision-theoretic approach for optimal item selection. Item contribution to the standardized expected utility of mastery testing is discussed. (CM)

Geriatric Anxiety Scale: item response theory analysis, differential item functioning, and creation of a ten-item short form (GAS-10).

Science.gov (United States)

Mueller, Anne E; Segal, Daniel L; Gavett, Brandon; Marty, Meghan A; Yochim, Brian; June, Andrea; Coolidge, Frederick L

2015-07-01

The Geriatric Anxiety Scale (GAS; Segal et al. (Segal, D. L., June, A., Payne, M., Coolidge, F. L. and Yochim, B. (2010). Journal of Anxiety Disorders, 24, 709-714. doi:10.1016/j.janxdis.2010.05.002) is a self-report measure of anxiety that was designed to address unique issues associated with anxiety assessment in older adults. This study is the first to use item response theory (IRT) to examine the psychometric properties of a measure of anxiety in older adults. A large sample of older adults (n = 581; mean age = 72.32 years, SD = 7.64 years, range = 60 to 96 years; 64% women; 88% European American) completed the GAS. IRT properties were examined. The presence of differential item functioning (DIF) or measurement bias by age and sex was assessed, and a ten-item short form of the GAS (called the GAS-10) was created. All GAS items had discrimination parameters of 1.07 or greater. Items from the somatic subscale tended to have lower discrimination parameters than items on the cognitive or affective subscales. Two items were flagged for DIF, but the impact of the DIF was negligible. Women scored significantly higher than men on the GAS and its subscales. Participants in the young-old group (60 to 79 years old) scored significantly higher on the cognitive subscale than participants in the old-old group (80 years old and older). Results from the IRT analyses indicated that the GAS and GAS-10 have strong psychometric properties among older adults. We conclude by discussing implications and future research directions.

Asymptotic Standard Errors for Item Response Theory True Score Equating of Polytomous Items

Science.gov (United States)

Cher Wong, Cheow

2015-01-01

Building on previous works by Lord and Ogasawara for dichotomous items, this article proposes an approach to derive the asymptotic standard errors of item response theory true score equating involving polytomous items, for equivalent and nonequivalent groups of examinees. This analytical approach could be used in place of empirical methods like…

MIMIC Methods for Assessing Differential Item Functioning in Polytomous Items

Science.gov (United States)

Wang, Wen-Chung; Shih, Ching-Lin

2010-01-01

Three multiple indicators-multiple causes (MIMIC) methods, namely, the standard MIMIC method (M-ST), the MIMIC method with scale purification (M-SP), and the MIMIC method with a pure anchor (M-PA), were developed to assess differential item functioning (DIF) in polytomous items. In a series of simulations, it appeared that all three methods…

Perception that "everything requires a lot of effort": transcultural SCL-25 item validation.

Science.gov (United States)

Moreau, Nicolas; Hassan, Ghayda; Rousseau, Cécile; Chenguiti, Khalid

2009-09-01

This brief report illustrates how the migration context can affect specific item validity of mental health measures. The SCL-25 was administered to 432 recently settled immigrants (220 Haitian and 212 Arabs). We performed descriptive analyses, as well as Infit and Outfit statistics analyses using WINSTEPS Rasch Measurement Software based on Item Response Theory. The participants' comments about the item You feel everything requires a lot of effort in the SCL-25 were also qualitatively analyzed. Results revealed that the item You feel everything requires a lot of effort is an outlier and does not adjust in an expected and valid fashion with its cluster items, as it is over-endorsed by Haitian and Arab healthy participants. Our study thus shows that, in transcultural mental health research, the cultural and migratory contexts may interact and significantly influence the meaning of some symptom items and consequently, the validity of symptom scales.

Evaluation of Northwest University, Kano Post-UTME Test Items Using Item Response Theory

Science.gov (United States)

Bichi, Ado Abdu; Hafiz, Hadiza; Bello, Samira Abdullahi

2016-01-01

High-stakes testing is used for the purposes of providing results that have important consequences. Validity is the cornerstone upon which all measurement systems are built. This study applied the Item Response Theory principles to analyse Northwest University Kano Post-UTME Economics test items. The developed fifty (50) economics test items was…

Overview of classical test theory and item response theory for the quantitative assessment of items in developing patient-reported outcomes measures.

Science.gov (United States)

Cappelleri, Joseph C; Jason Lundy, J; Hays, Ron D

2014-05-01

The US Food and Drug Administration's guidance for industry document on patient-reported outcomes (PRO) defines content validity as "the extent to which the instrument measures the concept of interest" (FDA, 2009, p. 12). According to Strauss and Smith (2009), construct validity "is now generally viewed as a unifying form of validity for psychological measurements, subsuming both content and criterion validity" (p. 7). Hence, both qualitative and quantitative information are essential in evaluating the validity of measures. We review classical test theory and item response theory (IRT) approaches to evaluating PRO measures, including frequency of responses to each category of the items in a multi-item scale, the distribution of scale scores, floor and ceiling effects, the relationship between item response options and the total score, and the extent to which hypothesized "difficulty" (severity) order of items is represented by observed responses. If a researcher has few qualitative data and wants to get preliminary information about the content validity of the instrument, then descriptive assessments using classical test theory should be the first step. As the sample size grows during subsequent stages of instrument development, confidence in the numerical estimates from Rasch and other IRT models (as well as those of classical test theory) would also grow. Classical test theory and IRT can be useful in providing a quantitative assessment of items and scales during the content-validity phase of PRO-measure development. Depending on the particular type of measure and the specific circumstances, the classical test theory and/or the IRT should be considered to help maximize the content validity of PRO measures. Copyright © 2014 Elsevier HS Journals, Inc. All rights reserved.

Using Differential Item Functioning Procedures to Explore Sources of Item Difficulty and Group Performance Characteristics.

Science.gov (United States)

Scheuneman, Janice Dowd; Gerritz, Kalle

1990-01-01

Differential item functioning (DIF) methodology for revealing sources of item difficulty and performance characteristics of different groups was explored. A total of 150 Scholastic Aptitude Test items and 132 Graduate Record Examination general test items were analyzed. DIF was evaluated for males and females and Blacks and Whites. (SLD)

Item Response Data Analysis Using Stata Item Response Theory Package

Science.gov (United States)

Yang, Ji Seung; Zheng, Xiaying

2018-01-01

The purpose of this article is to introduce and review the capability and performance of the Stata item response theory (IRT) package that is available from Stata v.14, 2015. Using a simulated data set and a publicly available item response data set extracted from Programme of International Student Assessment, we review the IRT package from…

The impact of fit manufacturing on green manufacturing: A review

Science.gov (United States)

Qi, Ang Nian; Sin, Tan Chan; Fathullah, M.; Lee, C. C.

2017-09-01

Fit manufacturing and Green manufacturing are a new trend principle and concept. They are getting popular in industrial. This paper is identifying the impact between Fit manufacturing and Green manufacturing. Besides Fit manufacturing, Lean manufacturing, Agile manufacturing and Sustainable manufacturing gives big impacts to Green Manufacturing. On top of that, this paper also discuss the benefits of applying Fit manufacturing and Green manufacturing in industrial as well as environment. Hence, applications of Fit manufacturing and Green Manufacturing are increasing year by year.

Item Banking with Embedded Standards

Science.gov (United States)

MacCann, Robert G.; Stanley, Gordon

2009-01-01

An item banking method that does not use Item Response Theory (IRT) is described. This method provides a comparable grading system across schools that would be suitable for low-stakes testing. It uses the Angoff standard-setting method to obtain item ratings that are stored with each item. An example of such a grading system is given, showing how…

Methodology for appreciation the manufacturing castings from perspective of circular economy

Science.gov (United States)

Soporan, V. F.; Crișan, M.; Lehene, T.; Pop, A. L.

2016-06-01

This paper presents a methodology for studying the trends toward developing circular economy, comprising the following steps: description the field analyzed statistically and technological, establishing assessment criteria, establishing the event which will be analyzed and its description and evaluation of the event from the perspective of circular economy. The case study was designed to the manufacture castings through the analysis, after the methodology proposed, by the work of the 71-th World Foundry Congress in 2014 from Bilbao. The conclusion of this approach shows us that the manufacture castings through the trends expressed fall in the principles of circular economy. At the level of resources needed for the manufacturing process of castings - specifically immaterial resources, materials and energy, are analyzed at all levels, specific phases, namely: 1. Information analysis specific for the field; 2. Analysis preparation in terms of manufacturing technology and technological infrastructure available; 3. Analysis of manufacturing castings; 4. Analysis of the results of the manufacturing process; 5. Analysis of exploitation and disposal at end of life cycle; 6. Analysis of other phases that contribute to achieving castings; 7. Analysis of the entire process in terms of respecting the environment and sustainable development. The analysis method on a field belonging to the specific requirements of circular economy is made by analyzing a global event. This comprises the following stages: Establish specific criteria for the analyzed domain in relation to the circular economy; Specifying event works falling within the criteria set, which will be analyzed, and justification for selection.

The Impact of Three Factors on the Recovery of Item Parameters for the Three-Parameter Logistic Model

Science.gov (United States)

Kim, Kyung Yong; Lee, Won-Chan

2017-01-01

This article provides a detailed description of three factors (specification of the ability distribution, numerical integration, and frame of reference for the item parameter estimates) that might affect the item parameter estimation of the three-parameter logistic model, and compares five item calibration methods, which are combinations of the…

Overview of Additive Manufacturing Initiatives at NASA Marshall Space Flight Center

Science.gov (United States)

Clinton, R. G., Jr.

2018-01-01

NASA's In Space Manufacturing Initiative (ISM) includes: The case for ISM - why; ISM path to exploration - results from the 3D Printing In Zero-G Technology Demonstration - ISM challenges; In space Robotic Manufacturing and Assembly (IRMA); Additive construction. Additively Manufacturing (AM) development for liquid rocket engine space flight hardware. MSFC standard and specification for additively manufactured space flight hardware. Summary.

An EPQ Inventory Model with Allowable Shortages for Deteriorating Items under Trade Credit Policy

Directory of Open Access Journals (Sweden)

Zohreh Molamohamadi

2014-01-01

Full Text Available This paper attempts to obtain the replenishment policy of a manufacturer under EPQ inventory model with backorder. It is assumed here that the manufacturer delays paying for the received goods from the supplier and the items start deteriorating as soon as they are being produced. Based on these assumptions, the manufacturer’s inventory model is formulated, and cuckoo search algorithm is applied then to find the replenishment time, order quantity, and selling price with the objective of maximizing the manufacturer’s total net profit. Besides, the traditional inventory system is shown as a special case of the proposed model in this paper, and numerical examples are given to demonstrate better performance of trade credit. These examples are also used to compare the results of cuckoo search algorithm with genetic algorithm and investigate the effects of the model parameters on its variables and net profit.

Modular Open-Source Software for Item Factor Analysis

Science.gov (United States)

Pritikin, Joshua N.; Hunter, Micheal D.; Boker, Steven M.

2015-01-01

This article introduces an item factor analysis (IFA) module for "OpenMx," a free, open-source, and modular statistical modeling package that runs within the R programming environment on GNU/Linux, Mac OS X, and Microsoft Windows. The IFA module offers a novel model specification language that is well suited to programmatic generation…

P2-19: The Effect of item Repetition on Item-Context Association Depends on the Prior Exposure of Items

Directory of Open Access Journals (Sweden)

Hongmi Lee

2012-10-01

Full Text Available Previous studies have reported conflicting findings on whether item repetition has beneficial or detrimental effects on source memory. To reconcile such contradictions, we investigated whether the degree of pre-exposure of items can be a potential modulating factor. The experimental procedures spanned two consecutive days. On Day 1, participants were exposed to a set of unfamiliar faces. On Day 2, the same faces presented on the previous day were used again in half of the participants, whereas novel faces were used for the other half. Day 2 procedures consisted of three successive phases: item repetition, source association, and source memory test. In the item repetition phase, half of the face stimuli were repeatedly presented while participants were making male/female judgments. During the source association phase, both the repeated and the unrepeated faces appeared in one of the four locations on the screen. Finally, participants were tested on the location in which a given face was presented during the previous phase and reported the confidence of their memory. Source memory accuracy was measured as the percentage of correct non-guess trials. As results, we found a significant interaction between prior exposure and repetition. Repetition impaired source memory when the items had been pre-exposed on Day 1, while it led to greater accuracy in novel ones. These results show that pre-experimental exposure can modulate the effects of repetition on associative binding between an item and its contextual information, suggesting that pre-existing representation and novelty signal interact to form new episodic memory.

Development of Rasch-based item banks for the assessment of work performance in patients with musculoskeletal diseases.

Science.gov (United States)

Mueller, Evelyn A; Bengel, Juergen; Wirtz, Markus A

2013-12-01

This study aimed to develop a self-description assessment instrument to measure work performance in patients with musculoskeletal diseases. In terms of the International Classification of Functioning, Disability and Health (ICF), work performance is defined as the degree of meeting the work demands (activities) at the actual workplace (environment). To account for the fact that work performance depends on the work demands of the job, we strived to develop item banks that allow a flexible use of item subgroups depending on the specific work demands of the patients' jobs. Item development included the collection of work tasks from literature and content validation through expert surveys and patient interviews. The resulting 122 items were answered by 621 patients with musculoskeletal diseases. Exploratory factor analysis to ascertain dimensionality and Rasch analysis (partial credit model) for each of the resulting dimensions were performed. Exploratory factor analysis resulted in four dimensions, and subsequent Rasch analysis led to the following item banks: 'impaired productivity' (15 items), 'impaired cognitive performance' (18), 'impaired coping with stress' (13) and 'impaired physical performance' (low physical workload 20 items, high physical workload 10 items). The item banks exhibited person separation indices (reliability) between 0.89 and 0.96. The assessment of work performance adds the activities component to the more commonly employed participation component of the ICF-model. The four item banks can be adapted to specific jobs where necessary without losing comparability of person measures, as the item banks are based on Rasch analysis.

Clean Energy Manufacturing Analysis Center Benchmark Report: Framework and Methodologies

Energy Technology Data Exchange (ETDEWEB)

Sandor, Debra [National Renewable Energy Lab. (NREL), Golden, CO (United States); Chung, Donald [National Renewable Energy Lab. (NREL), Golden, CO (United States); Keyser, David [National Renewable Energy Lab. (NREL), Golden, CO (United States); Mann, Margaret [National Renewable Energy Lab. (NREL), Golden, CO (United States); Engel-Cox, Jill [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-05-23

This report documents the CEMAC methodologies for developing and reporting annual global clean energy manufacturing benchmarks. The report reviews previously published manufacturing benchmark reports and foundational data, establishes a framework for benchmarking clean energy technologies, describes the CEMAC benchmark analysis methodologies, and describes the application of the methodologies to the manufacturing of four specific clean energy technologies.

Additive Manufacturing of Fuel Injectors

Energy Technology Data Exchange (ETDEWEB)

Sadek Tadros, Dr. Alber Alphonse [Edison Welding Institute, Inc., Columbus, OH (United States); Ritter, Dr. George W. [Edison Welding Institute, Inc., Columbus, OH (United States); Drews, Charles Donald [Edison Welding Institute, Inc., Columbus, OH (United States); Ryan, Daniel [Solar Turbines Inc., San Diego, CA (United States)

2017-10-24

Additive manufacturing (AM), also known as 3D-printing, has been shifting from a novelty prototyping paradigm to a legitimate manufacturing tool capable of creating components for highly complex engineered products. An emerging AM technology for producing metal parts is the laser powder bed fusion (L-PBF) process; however, industry manufacturing specifications and component design practices for L-PBF have not yet been established. Solar Turbines Incorporated (Solar), an industrial gas turbine manufacturer, has been evaluating AM technology for development and production applications with the desire to enable accelerated product development cycle times, overall turbine efficiency improvements, and supply chain flexibility relative to conventional manufacturing processes (casting, brazing, welding). Accordingly, Solar teamed with EWI on a joint two-and-a-half-year project with the goal of developing a production L-PBF AM process capable of consistently producing high-nickel alloy material suitable for high temperature gas turbine engine fuel injector components. The project plan tasks were designed to understand the interaction of the process variables and their combined impact on the resultant AM material quality. The composition of the high-nickel alloy powders selected for this program met the conventional cast Hastelloy X compositional limits and were commercially available in different particle size distributions (PSD) from two suppliers. Solar produced all the test articles and both EWI and Solar shared responsibility for analyzing them. The effects of powder metal input stock, laser parameters, heat treatments, and post-finishing methods were evaluated. This process knowledge was then used to generate tensile, fatigue, and creep material properties data curves suitable for component design activities. The key process controls for ensuring consistent material properties were documented in AM powder and process specifications. The basic components of the project

The Future of Pharmaceutical Manufacturing Sciences

DEFF Research Database (Denmark)

Rantanen, Jukka; Khinast, Johannes

2015-01-01

The entire pharmaceutical sector is in an urgent need of both innovative technological solutions and fundamental scientific work, enabling the production of highly engineered drug products. Commercial-scale manufacturing of complex drug delivery systems (DDSs) using the existing technologies...... is challenging. This review covers important elements of manufacturing sciences, beginning with risk management strategies and design of experiments (DoE) techniques. Experimental techniques should, where possible, be supported by computational approaches. With that regard, state-of-art mechanistic process...... control solutions. Last part of the review addresses future manufacturing solutions, covering continuous processing and, specifically, hot-melt processing and printing-based technologies. Finally, challenges related to implementing these technologies as a part of future health care systems are discussed....

Specific PVMaT R and D in CdTe product manufacturing: Phase 1 annual report, 5 May 1998--4 May 1999

Energy Technology Data Exchange (ETDEWEB)

Bohland, J.; Kormanyos, K.; Faykosh, G.; Champion, V.; Cox, S.; McCarthur, M.; Dapkus, T.; Kamm, K.; Flis, M.

2000-03-01

This report documents the work performed by First Solar, LLC, during the first year of this Photovoltaic Manufacturing Technology (PVMaT) subcontract. The following milestones were successfully completed: (1) Initiate lamination development program by interviewing key suppliers and experts such as STR, Inc., ARRI, and automotive glass manufacturers; (2) Complete process specification for high-throughput laminator; (3) Initiate contact with module testing laboratory and complete preliminary module design review; (4) Complete review and survey of current environmental, health and safety (EHS) programs; (5) Complete design specifications for the high-throughput laminator; (6) Complete preliminary testing of modules; (7) Establish Qualification Testing Schedule; (8) Develop plans for critical areas of EHS improvement with the assistance of industry experts such as OSHA On-Site Consultation; (9) Begin de-bug of high-throughput laminator; (10) Initiate qualification testing on First Solar's standard modules; (11) Initiate EHS improvement projects; (12) Complete prove-in of high-throughput laminator at a rate of 30 modules per hour; (13) Complete report on lamination rates, yields, and reductions in labor and equipment costs; (14) Complete qualification testing on First Solar's standard module for IEEE 1262 and UL 1703; and (15) Complete implementation of critical EHS improvements.

Investigating the Impact of Item Parameter Drift for Item Response Theory Models with Mixture Distributions

Directory of Open Access Journals (Sweden)

Yoon Soo ePark

2016-02-01

Full Text Available This study investigates the impact of item parameter drift (IPD on parameter and ability estimation when the underlying measurement model fits a mixture distribution, thereby violating the item invariance property of unidimensional item response theory (IRT models. An empirical study was conducted to demonstrate the occurrence of both IPD and an underlying mixture distribution using real-world data. Twenty-one trended anchor items from the 1999, 2003, and 2007 administrations of Trends in International Mathematics and Science Study (TIMSS were analyzed using unidimensional and mixture IRT models. TIMSS treats trended anchor items as invariant over testing administrations and uses pre-calibrated item parameters based on unidimensional IRT. However, empirical results showed evidence of two latent subgroups with IPD. Results showed changes in the distribution of examinee ability between latent classes over the three administrations. A simulation study was conducted to examine the impact of IPD on the estimation of ability and item parameters, when data have underlying mixture distributions. Simulations used data generated from a mixture IRT model and estimated using unidimensional IRT. Results showed that data reflecting IPD using mixture IRT model led to IPD in the unidimensional IRT model. Changes in the distribution of examinee ability also affected item parameters. Moreover, drift with respect to item discrimination and distribution of examinee ability affected estimates of examinee ability. These findings demonstrate the need to caution and evaluate IPD using a mixture IRT framework to understand its effect on item parameters and examinee ability.

Investigating the Impact of Item Parameter Drift for Item Response Theory Models with Mixture Distributions.

Science.gov (United States)

Park, Yoon Soo; Lee, Young-Sun; Xing, Kuan

2016-01-01

This study investigates the impact of item parameter drift (IPD) on parameter and ability estimation when the underlying measurement model fits a mixture distribution, thereby violating the item invariance property of unidimensional item response theory (IRT) models. An empirical study was conducted to demonstrate the occurrence of both IPD and an underlying mixture distribution using real-world data. Twenty-one trended anchor items from the 1999, 2003, and 2007 administrations of Trends in International Mathematics and Science Study (TIMSS) were analyzed using unidimensional and mixture IRT models. TIMSS treats trended anchor items as invariant over testing administrations and uses pre-calibrated item parameters based on unidimensional IRT. However, empirical results showed evidence of two latent subgroups with IPD. Results also showed changes in the distribution of examinee ability between latent classes over the three administrations. A simulation study was conducted to examine the impact of IPD on the estimation of ability and item parameters, when data have underlying mixture distributions. Simulations used data generated from a mixture IRT model and estimated using unidimensional IRT. Results showed that data reflecting IPD using mixture IRT model led to IPD in the unidimensional IRT model. Changes in the distribution of examinee ability also affected item parameters. Moreover, drift with respect to item discrimination and distribution of examinee ability affected estimates of examinee ability. These findings demonstrate the need to caution and evaluate IPD using a mixture IRT framework to understand its effects on item parameters and examinee ability.

The Manufacturing Engineering Department of the Future

DEFF Research Database (Denmark)

Alting, Leo

1998-01-01

When discussing manufacturing engineering education you always end up discussing curricula development, course design, specific topics to be taught, etc. Very rarely it is discussed, how a manufacturing engineering department ought to be designed to create an attractive environment for students...... and the requirements to the products/services identified. The organisation necessary to develop the department is outlined as well as the process to implement the vision....

Towards Knowledge Management for Smart Manufacturing.

Science.gov (United States)

Feng, Shaw C; Bernstein, William Z; Hedberg, Thomas; Feeney, Allison Barnard

2017-09-01

The need for capturing knowledge in the digital form in design, process planning, production, and inspection has increasingly become an issue in manufacturing industries as the variety and complexity of product lifecycle applications increase. Both knowledge and data need to be well managed for quality assurance, lifecycle-impact assessment, and design improvement. Some technical barriers exist today that inhibit industry from fully utilizing design, planning, processing, and inspection knowledge. The primary barrier is a lack of a well-accepted mechanism that enables users to integrate data and knowledge. This paper prescribes knowledge management to address a lack of mechanisms for integrating, sharing, and updating domain-specific knowledge in smart manufacturing. Aspects of the knowledge constructs include conceptual design, detailed design, process planning, material property, production, and inspection. The main contribution of this paper is to provide a methodology on what knowledge manufacturing organizations access, update, and archive in the context of smart manufacturing. The case study in this paper provides some example knowledge objects to enable smart manufacturing.

Turbine airfoil manufacturing technology

Energy Technology Data Exchange (ETDEWEB)

Kortovich, C. [PCC Airfoils, Inc., Beachwood, OH (United States)

1995-12-31

The specific goal of this program is to define manufacturing methods that will allow single crystal technology to be applied to complex-cored airfoils components for power generation applications. Tasks addressed include: alloy melt practice to reduce the sulfur content; improvement of casting process; core materials design; and grain orientation control.

Exploring differential item functioning (DIF) with the Rasch model: A comparison of gender differences on eighth-grade science items in the United States and Spain

Science.gov (United States)

Calvert, Tasha

Despite the attention that has been given to gender and science, boys continue to outperform girls in science achievement, particularly by the end of secondary school. Because it is unclear whether gender differences have narrowed over time (Leder, 1992; Willingham & Cole, 1997), it is important to continue a line of inquiry into the nature of gender differences, specifically at the international level. The purpose of this study was to investigate gender differences in science achievement across two countries: United States and Spain. A secondary purpose was to demonstrate an alternative method for exploring gender differences based on the many-faceted Rasch model (1980). A secondary analysis of the data from the Third International Mathematics and Science Study (TIMSS) was used to examine the relationship between gender DIF (differential item functioning) and item characteristics (item type, content, and performance expectation) across both countries. Nationally representative samples of eighth grade students in the United States and Spain who participated in TIMSS were analyzed to answer the research questions in this study. In both countries, girls showed an advantage over boys on life science items and most extended response items, whereas boys, by and large, had an advantage on earth science, physics, and chemistry items. However, even within areas that favored boys, such as physics, there were items that were differentially easier for girls. In general, patterns in gender differences were similar across both countries although there were a few differences between the countries on individual items. It was concluded that simply looking at mean differences does not provide an adequate understanding of the nature of gender differences in science achievement.

Semantic Relevance, Domain Specificity and the Sensory/Functional Theory of Category-Specificity

Science.gov (United States)

Sartori, Giuseppe; Gnoato, Francesca; Mariani, Ilenia; Prioni, Sara; Lombardi, Luigi

2007-01-01

According to the sensory/functional theory of semantic memory, Living items rely more on Sensory knowledge than Non-living ones. The sensory/functional explanation of category-specificity assumes that semantic features are organised on the basis of their content. We report here a study on DAT patients with impaired performance on Living items and…

In-Space Manufacturing Baseline Property Development

Science.gov (United States)

Stockman, Tom; Schneider, Judith; Prater, Tracie; Bean, Quincy; Werkheiser, Nicki

2016-01-01

The In-Space Manufacturing (ISM) project at NASA Marshall Space Flight Center currently operates a 3D FDM (fused deposition modeling) printer onboard the International Space Station. In order to enable utilization of this capability by designer, the project needs to establish characteristic material properties for materials produced using the process. This is difficult for additive manufacturing since standards and specifications do not yet exist for these technologies. Due to availability of crew time, there are limitations to the sample size which in turn limits the application of the traditional design allowables approaches to develop a materials property database for designers. In this study, various approaches to development of material databases were evaluated for use by designers of space systems who wish to leverage in-space manufacturing capabilities. This study focuses on alternative statistical techniques for baseline property development to support in-space manufacturing.

Maintenance scheduling of a manufacturing system subject to deterioration

International Nuclear Information System (INIS)

Ahmadi, Reza; Newby, Martin

2011-01-01

This paper presents an integrated model for the joint determination of both optimal inspection strategy and optimal repair policy for a manufacturing system whose resulting output is subject to system state. An appropriate maintenance strategy is essential to optimize revenue from a manufacturing system which is in continuous operation and subject to deterioration. The optimum policy balances the amount of maintenance required to increase availability against the loss of revenue arising from the down time: insufficient maintenance leads to an increase in the number of defective items, low profit and low maintenance cost; excessive maintenance results in a reduction in the proportion of defective items, high profit and high maintenance cost. In this paper, an intensity control model adapted to partial information provides an optimal inspection intensity and repair degree of the system as an optimal control process to yield maximum revenue. The solution is obtained through formulating an equivalent deterministic Hamilton-Jacobi equation. A numerical example is provided to illustrate the behavior of the optimal control process. The optimal control process determines a solution to both optimum inspection frequency and optimal replacement policy which results in an optimal production run length of the system. - Highlights: → We develop an optimum asset management strategy based on the revenue generated by the asset. → The optimum strategy controls the intensity, rate of occurrence, of interruptions to service. → The decisions are based on partial observation of the system and do not need perfect information. There is no need for continuous monitoring of the system.

A single exercise bout enhances the manufacture of viral-specific T-cells from healthy donors: implications for allogeneic adoptive transfer immunotherapy

OpenAIRE

Guillaume Spielmann; Catherine M. Bollard; Hawley Kunz; Patrick J. Hanley; Richard J. Simpson

2016-01-01

Cytomegalovirus (CMV) and Epstein-Barr virus (EBV) infections remain a major cause of morbidity and mortality after allogeneic hematopoietic stem cell transplantation (HSCT). The adoptive transfer of donor-derived viral-specific cytotoxic T-cells (VSTs) is an effective treatment for controlling CMV and EBV infections after HSCT; however, new practical methods are required to augment the ex vivo manufacture of multi-VSTs from healthy donors. This study investigated the effects of a single exer...

The measurement of cyberbullying: dimensional structure and relative item severity and discrimination.

Science.gov (United States)

Menesini, Ersilia; Nocentini, Annalaura; Calussi, Pamela

2011-05-01

In relation to a sample of 1,092 Italian adolescents (50.9% females), the present study aims to: (a) analyze the most parsimonious structure of the cyberbullying and cybervictimization construct in male and female Italian adolescents through confirmatory factor analysis; and (b) analyze the severity and the discrimination parameters of each act using the item response theory. Results showed that the structure of the cyberbullying scale for perpetrated and received behaviors in both genders could best be represented by a monodimensional model where each item lies on a continuum of severity of aggressive acts. For both genders, the less severe acts are silent/prank calls and insults on instant messaging, and the most severe acts are unpleasant pictures/photos on Web sites, phone pictures/photos/videos of intimate scenes, and phone pictures/photos/videos of violent scenes. The items nasty text messages, nasty or rude e-mails, insults on Web sites, insults in chatrooms, and insults on blogs range from moderate to high levels of severity. Regarding the discrimination level of the acts, several items emerged as good indicators at various levels of cyberbullying and cybervictimization severity, with the exception of silent/prank calls. Furthermore, gender specificities underlined that the visual items can be considered good indicators of severe cyberbullies and cybervictims only in males. This information can help in understanding better the nature of the phenomenon, its severity in a given population, and to plan more specific prevention and intervention strategies.

Management and schedule challenges for fossil projects in the 1990's. Working Group Three: Challenges and action items

International Nuclear Information System (INIS)

Anon.

1991-01-01

The discussions of the working group resulted in identification of the following management challenges: New generation capacity - before 1995, after 1995; Shortages of critical resources - engineers and crafts, manufacturing capacity; Competitive restrictions; Management philosophy - not the owners' problem; delay commitment; custom plants; proven technology; build and own myself. The paper also lists action items under 3 categories: actions to increase resources and decrease needs; fostering competitive incentives; and changing management philosophy

Survey of US Department of Defense Manufacturing Technology Program activities applicable to civilian manufacturing industries. Final report

Energy Technology Data Exchange (ETDEWEB)

Azimi, S.A.; Conrad, J.L.; Reed, J.E.

1985-03-01

Intent of the survey was to identify and characterize activities potentially applicable to improving energy efficiency and overall productivity in the civilian manufacturing industries. The civilian industries emphasized were the general manufacturing industries (including fabricated metals, glass, machinery, paper, plastic, textile, and transportation equipment manufacturing) and the primary metals industries (including primary aluminum, copper, steel, and zinc production). The principal steps in the survey were to: develop overview taxonomies of the general manufacturing and primary metals industries as well as specific industry taxonomies; identify needs and opportunities for improving process energy efficiency and productivity in the industries included; identify federal programs, capabilities, and special technical expertise that might be relevant to industry's needs and opportunities; contact federal laboratories/facilities, through visits and other forms of inquiry; prepare formatted profiles (descriptions) potentially applicable work efforts; review findings with industry; and compile and evaluate industry responses.

Modified economic order quantity (EOQ model for items with imperfect quality: Game-theoretical approaches

Directory of Open Access Journals (Sweden)

Milad Elyasi

2014-04-01

Full Text Available In the recent decade, studying the economic order quantity (EOQ models with imperfect quality has appealed to many researchers. Only few papers are published discussing EOQ models with imperfect items in a supply chain. In this paper, a two-echelon decentralized supply chain consisting of a manufacture and a supplier that both face just in time (JIT inventory problem is considered. It is sought to find the optimal number of the shipments and the quantity of each shipment in a way that minimizes the both manufacturer’s and the supplier’s cost functions. To the authors’ best knowledge, this is the first paper that deals with imperfect items in a decentralized supply chain. Thereby, three different game theoretical solution approaches consisting of two non-cooperative games and a cooperative game are proposed. Comparing the results of three different scenarios with those of the centralized model, the conclusions are drawn to obtain the best approach.

An Analysis of the Operational Environments of Manufacturing Firms ...

African Journals Online (AJOL)

Our efforts in this research have been geared towards analyzing the operational environments of manufacturing firms in Aba, South-East, Nigeria. Specifically, the case study was Manufacturers Association of Nigeria (MAN), Abia chapter. Eight five percent of MAN‟s membership was studied. Percentages and test of ...

Modular Hydropower Engineering and Pilot Scale Manufacturing

Energy Technology Data Exchange (ETDEWEB)

Chesser, Phillip C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-09-01

Emrgy has developed, prototyped and tested a modular hydropower system for renewable energy generation. ORNL worked with Emrgy to demonstrate the use of additive manufacturing in the production of the hydrofoils and spokes for the hydrokinetic system. Specifically, during Phase 1 of this effort, ORNL printed and finished machined patterns for both the hydrofoils and spokes that were subsequently used in a sand casting manufacturing process. Emrgy utilized the sand castings for a pilot installation in Denver, CO, where the parts represented an 80% cost savings from the previous prototype build that was manufactured using subtractive manufacturing. In addition, the castings were completed with ORNL’s newly developed AlCeMg alloy that will be tested for performance improvements including higher corrosion resistance in a water application than the 6160 alloy used previously

TF4SM: A Framework for Developing Traceability Solutions in Small Manufacturing Companies

Science.gov (United States)

Bordel Sánchez, Borja; Alcarria, Ramón; Martín, Diego; Robles, Tomás

2015-01-01

Nowadays, manufacturing processes have become highly complex. Besides, more and more, governmental institutions require companies to implement systems to trace a product’s life (especially for foods, clinical materials or similar items). In this paper, we propose a new framework, based on cyber-physical systems, for developing traceability systems in small manufacturing companies (which because of their size cannot implement other commercial products). We propose a general theoretical framework, study the requirements of these companies in relation to traceability systems, propose a reference architecture based on both previous elements and build the first minimum functional prototype, to compare our solution to a traditional tag-based traceability system. Results show that our system reduces the number of inefficiencies and reaction time. PMID:26610509

Expert system for designing the manufacturing conditions

International Nuclear Information System (INIS)

Henin, F.

1990-01-01

The expert system TOTEM (French acronym for Material and Time Optimal Processing), used in computer aided manufacturing, is presented. The flow chart describing the TOTEM operation principles is given. The calculation rules which allow the optimization of the fabrication means are summarized. The steps of the TOTEM operations and an application example are included. TOTEM allows the standardization of the manufacturing specifications and takes into account technological improvements [fr

Manufacturing of nuclear power components in CDM

International Nuclear Information System (INIS)

Krishnan, J.; Jawale, S.B.

2002-01-01

Full text: In the nuclear research programme in India, Dr. H.J. Bhabha, the architecture of the Indian Nuclear programme felt a need for proto-type development and precision manufacturing facility to fulfill the requirements of mechanical components in establishing the manufacturing capability for the successful and self sustained nuclear programme. Centre for Design and Manufacture (CDM) hitherto known as CWS was established in 1964 to cater to the specific requirements of DAE and other associated units like ISRO, DRDO. Since then CDM has made multiple technological achievements and changes towards high quality products. The acquisition of up-to-date machines during High-Tech facility under VIII Plan project and Advance Precision Fabrication facility under IX Plan project has changed the capability of CDM towards CAD, CAM, CAE and CNC machining centres. Considering the rapid growth in the design and manufacturing, it was renamed as Centre for Design and Manufacture in March 2002, with the mission of quality output through group effort and team work

Country status of application, manufacturing and sterilization of single-use medical products

International Nuclear Information System (INIS)

Norimah Yusof

1986-01-01

The paper reviews the current status of application of single-use medical products in Malaysia. The status of their manufacturing and sterilization is also discussed. The increasing production of such items calls for a more reliable and efficient sterilization technique in particular, radiation sterilization. In line with the demand and the effort to increase local production of medical products, UTN would be providing irradiation service together with research and development in this particular field by 1988. (author)

Development of the PROMIS positive emotional and sensory expectancies of smoking item banks.

Science.gov (United States)

Tucker, Joan S; Shadel, William G; Edelen, Maria Orlando; Stucky, Brian D; Li, Zhen; Hansen, Mark; Cai, Li

2014-09-01

The positive emotional and sensory expectancies of cigarette smoking include improved cognitive abilities, positive affective states, and pleasurable sensorimotor sensations. This paper describes development of Positive Emotional and Sensory Expectancies of Smoking item banks that will serve to standardize the assessment of this construct among daily and nondaily cigarette smokers. Data came from daily (N = 4,201) and nondaily (N =1,183) smokers who completed an online survey. To identify a unidimensional set of items, we conducted item factor analyses, item response theory analyses, and differential item functioning analyses. Additionally, we evaluated the performance of fixed-item short forms (SFs) and computer adaptive tests (CATs) to efficiently assess the construct. Eighteen items were included in the item banks (15 common across daily and nondaily smokers, 1 unique to daily, 2 unique to nondaily). The item banks are strongly unidimensional, highly reliable (reliability = 0.95 for both), and perform similarly across gender, age, and race/ethnicity groups. A SF common to daily and nondaily smokers consists of 6 items (reliability = 0.86). Results from simulated CATs indicated that, on average, less than 8 items are needed to assess the construct with adequate precision using the item banks. These analyses identified a new set of items that can assess the positive emotional and sensory expectancies of smoking in a reliable and standardized manner. Considerable efficiency in assessing this construct can be achieved by using the item bank SF, employing computer adaptive tests, or selecting subsets of items tailored to specific research or clinical purposes. © The Author 2014. Published by Oxford University Press on behalf of the Society for Research on Nicotine and Tobacco. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

The Domain-Specific Risk Taking Scale for Adult Populations: Item Selection and Preliminary Psychometric Properties

Science.gov (United States)

2009-12-01

result, and mostly based on content and face validity considerations, we deleted 8 items (e.g., “Cheating on an exam,” “ Plagiarizing a term paper,” etc...contributions of Ward Edwards. Norwell, MA: Kluwer Academic Press. [36] Weber, E.U., Ames, D., & Blais, A.-R. (2005). How do I choose thee? Let me count

Investigation of musculoskeletal symptoms in a manufacturing company in Brazil: a cross-sectional study.

Science.gov (United States)

Hembecker, Paula K; C Reis, Diogo; Konrath, Andréa C; A Gontijo, Leila; D Merino, Eugenio A

Musculoskeletal disorders are prevalent and represent the most common health problem among the working population in industrially-developing countries, with considerable costs and impact on quality of life. Despite the high incidence of disability insurance claims among Brazilian manufacturing-sector workers, only a few studies assessed musculoskeletal disorders prevalence. To provide information on the prevalence of musculoskeletal disorders among manufacturing-sector workers and to explore the relationship between musculoskeletal disorders and sociodemographic and occupational characteristics in a medium metallurgical company located in Brazil. A cross-sectional study was carried out. Data was collected through the use of a specifically-designed questionnaire and the items used to collect musculoskeletal disorders data were based on the Nordic Musculoskeletal Questionnaire. Descriptive statistics were used and multivariate logistic regression analysis (plogistic regression analysis showed that company experience (p=0.02), presence of sleep disorders (p=0.00), self-reported general health state (p=0.00) and perform work pause (p=0.00) were significant risk factors for development of musculoskeletal disorders. Sociodemographic and work-related aspects are influential risk factors for musculoskeletal disorders. These results add comprehension about musculoskeletal disorders prevalence and suggest a need for greater emphasis on prevention strategies. Copyright © 2017 Associação Brasileira de Pesquisa e Pós-Graduação em Fisioterapia. Publicado por Elsevier Editora Ltda. All rights reserved.

The Technical Quality of Test Items Generated Using a Systematic Approach to Item Writing.

Science.gov (United States)

Siskind, Theresa G.; Anderson, Lorin W.

The study was designed to examine the similarity of response options generated by different item writers using a systematic approach to item writing. The similarity of response options to student responses for the same item stems presented in an open-ended format was also examined. A non-systematic (subject matter expertise) approach and a…

Gender and Minority Achievement Gaps in Science in Eighth Grade: Item Analyses of Nationally Representative Data. Research Report. ETS RR-17-36

Science.gov (United States)

Qian, Xiaoyu; Nandakumar, Ratna; Glutting, Joseoph; Ford, Danielle; Fifield, Steve

2017-01-01

In this study, we investigated gender and minority achievement gaps on 8th-grade science items employing a multilevel item response methodology. Both gaps were wider on physics and earth science items than on biology and chemistry items. Larger gender gaps were found on items with specific topics favoring male students than other items, for…

Performance measurement integrated information framework in e-Manufacturing

Science.gov (United States)

Teran, Hilaida; Hernandez, Juan Carlos; Vizán, Antonio; Ríos, José

2014-11-01

The implementation of Internet technologies has led to e-Manufacturing technologies becoming more widely used and to the development of tools for compiling, transforming and synchronising manufacturing data through the Web. In this context, a potential area for development is the extension of virtual manufacturing to performance measurement (PM) processes, a critical area for decision making and implementing improvement actions in manufacturing. This paper proposes a PM information framework to integrate decision support systems in e-Manufacturing. Specifically, the proposed framework offers a homogeneous PM information exchange model that can be applied through decision support in e-Manufacturing environment. Its application improves the necessary interoperability in decision-making data processing tasks. It comprises three sub-systems: a data model, a PM information platform and PM-Web services architecture. A practical example of data exchange for measurement processes in the area of equipment maintenance is shown to demonstrate the utility of the model.

Serum neuron-specific enolase, biogenic amino-acids and neurobehavioral function in lead-exposed workers from lead-acid battery manufacturing process.

Science.gov (United States)

Ravibabu, K; Barman, T; Rajmohan, H R

2015-01-01

The interaction between serum neuron-specific enolase (NSE), biogenic amino-acids and neurobehavioral function with blood lead levels in workers exposed to lead form lead-acid battery manufacturing process was not studied. To evaluate serum NSE and biogenic amino-acids (dopamine and serotonin) levels, and neurobehavioral performance among workers exposed to lead from lead-acid storage battery plant, and its relation with blood lead levels (BLLs). In a cross-sectional study, we performed biochemical and neurobehavioral function tests on 146 workers exposed to lead from lead-acid battery manufacturing process. BLLs were assessed by an atomic absorption spectrophotometer. Serum NSE, dopamine and serotonin were measured by ELISA. Neurobehavioral functions were assessed by CDC-recommended tests---simple reaction time (SRT), symbol digit substitution test (SDST), and serial digit learning test (SDLT). There was a significant correlation (r 0.199, pSDLT and SRT had also a significant positive correlation (r 0.238, p<0.01). NSE had a negative correlation (r -0.194, p<0.05) with serotonin level. Multiple linear regression analysis revealed that both SRT and SDST had positive significant associations with BLL. SRT also had a positive significant association with age. Serum NSE cannot be used as a marker for BLL. The only domain of neurobehavioral function tests that is affected by increased BLL in workers of lead-acid battery manufacturing process is that of the "attention and perception" (SDST).

A Method for Customer-driven Purchasing : Aligning Supplier interaction and Customer-driven manufacturing

OpenAIRE

Bäckstrand, Jenny

2012-01-01

The role of a purchaser has traditionally focused on acquiring standard items at the lowest possible cost. The ability to reduce unit cost has been the key performance indicator for purchasers. Most traditional purchasing strategies thus focus on optimizing this situation, focusing on the supplier interface only and not on customer value. However, for many manufacturing companies, the demand from their customers has changed lately. Not only low‐cost standard products but also customized produ...

Designing Collaborative Manufacturing Solutions for SMEs

DEFF Research Database (Denmark)

Radziwon, Agnieszka; Bogers, Marcel; Bilberg, Arne

2014-01-01

specifically examine how these SMEs collaborate with both competitors and complementors in an innovative automation project. The findings include a decreasing importance of monetary motivation, a direct competitors paradox, and leadership and ownership's issues, on both inter- and intra-company level.......In this paper, we investigate how small manufacturing companies can apply open innovation in the context of process innovation. We present a case study, with embedded action research elements, of a particular set of SMEs that implement a collaborative solution for manufacturing processes. We...

Generalizability theory and item response theory

NARCIS (Netherlands)

Glas, Cornelis A.W.; Eggen, T.J.H.M.; Veldkamp, B.P.

2012-01-01

Item response theory is usually applied to items with a selected-response format, such as multiple choice items, whereas generalizability theory is usually applied to constructed-response tasks assessed by raters. However, in many situations, raters may use rating scales consisting of items with a

Sharing the cost of redundant items

DEFF Research Database (Denmark)

Hougaard, Jens Leth; Moulin, Hervé

2014-01-01

We ask how to share the cost of finitely many public goods (items) among users with different needs: some smaller subsets of items are enough to serve the needs of each user, yet the cost of all items must be covered, even if this entails inefficiently paying for redundant items. Typical examples...... are network connectivity problems when an existing (possibly inefficient) network must be maintained. We axiomatize a family cost ratios based on simple liability indices, one for each agent and for each item, measuring the relative worth of this item across agents, and generating cost allocation rules...... additive in costs....

Trial manufacturing of titanium-carbon steel composite overpack

International Nuclear Information System (INIS)

Honma, Nobuyuki; Chiba, Takahiko; Tanai, Kenji

1999-11-01

This paper reports the results of design analysis and trial manufacturing of full-scale titanium-carbon steel composite overpacks. The overpack is one of the key components of the engineered barrier system, hence, it is necessary to confirm the applicability of current technique in their manufacture. The required thickness was calculated according to mechanical resistance analysis, based on models used in current nuclear facilities. The Adequacy of the calculated dimensions was confirmed by finite-element methods. To investigate the necessity of a radiation shielding function of the overpack, the irradiation from vitrified waste has been calculated. As a result, it was shown that shielding on handling and transport equipment is a more reasonable and practical approach than to increase thickness of overpack to attain a self-shielding capability. After the above investigation, trial manufacturing of full-scale model of titanium-carbon steel composite overpack has been carried out. For corrosion-resistant material, ASTM Grade-2 titanium was selected. The titanium layer was bonded individually to a cylindrical shell and fiat cover plates (top and bottom) made of carbon steel. For the cylindrical shell portion, a cylindrically formed titanium layer was fitted to the inner carbon steel vessel by shrinkage. For the flat cover plates (top and bottom), titanium plate material was coated by explosive bonding. Electron beam welding and gas metal arc welding were combined to weld of the cover plates to the body. No significant failure was evident from inspections of the fabrication process, and the applicability of current technology for manufacturing titanium-carbon steel composite overpack was confirmed. Future research and development items regarding titanium-carbon steel composite overpacks are also discussed. (author)

Generalizability theory and item response theory

OpenAIRE

Glas, Cornelis A.W.; Eggen, T.J.H.M.; Veldkamp, B.P.

2012-01-01

Item response theory is usually applied to items with a selected-response format, such as multiple choice items, whereas generalizability theory is usually applied to constructed-response tasks assessed by raters. However, in many situations, raters may use rating scales consisting of items with a selected-response format. This chapter presents a short overview of how item response theory and generalizability theory were integrated to model such assessments. Further, the precision of the esti...

The 12-item World Health Organization Disability Assessment Schedule II (WHO-DAS II: a nonparametric item response analysis

Directory of Open Access Journals (Sweden)

Fernandez Ana

2010-05-01

Full Text Available Abstract Background Previous studies have analyzed the psychometric properties of the World Health Organization Disability Assessment Schedule II (WHO-DAS II using classical omnibus measures of scale quality. These analyses are sample dependent and do not model item responses as a function of the underlying trait level. The main objective of this study was to examine the effectiveness of the WHO-DAS II items and their options in discriminating between changes in the underlying disability level by means of item response analyses. We also explored differential item functioning (DIF in men and women. Methods The participants were 3615 adult general practice patients from 17 regions of Spain, with a first diagnosed major depressive episode. The 12-item WHO-DAS II was administered by the general practitioners during the consultation. We used a non-parametric item response method (Kernel-Smoothing implemented with the TestGraf software to examine the effectiveness of each item (item characteristic curves and their options (option characteristic curves in discriminating between changes in the underliying disability level. We examined composite DIF to know whether women had a higher probability than men of endorsing each item. Results Item response analyses indicated that the twelve items forming the WHO-DAS II perform very well. All items were determined to provide good discrimination across varying standardized levels of the trait. The items also had option characteristic curves that showed good discrimination, given that each increasing option became more likely than the previous as a function of increasing trait level. No gender-related DIF was found on any of the items. Conclusions All WHO-DAS II items were very good at assessing overall disability. Our results supported the appropriateness of the weights assigned to response option categories and showed an absence of gender differences in item functioning.

Evaluation of five guidelines for option development in multiple-choice item-writing.

Science.gov (United States)

Martínez, Rafael J; Moreno, Rafael; Martín, Irene; Trigo, M Eva

2009-05-01

This paper evaluates certain guidelines for writing multiple-choice test items. The analysis of the responses of 5013 subjects to 630 items from 21 university classroom achievement tests suggests that an option should not differ in terms of heterogeneous content because such error has a slight but harmful effect on item discrimination. This also occurs with the "None of the above" option when it is the correct one. In contrast, results do not show the supposedly negative effects of a different-length option, the use of specific determiners, or the use of the "All of the above" option, which not only decreases difficulty but also improves discrimination when it is the correct option.

Item Response Theory with Covariates (IRT-C): Assessing Item Recovery and Differential Item Functioning for the Three-Parameter Logistic Model

Science.gov (United States)

Tay, Louis; Huang, Qiming; Vermunt, Jeroen K.

2016-01-01

In large-scale testing, the use of multigroup approaches is limited for assessing differential item functioning (DIF) across multiple variables as DIF is examined for each variable separately. In contrast, the item response theory with covariate (IRT-C) procedure can be used to examine DIF across multiple variables (covariates) simultaneously. To…

INTRODUCTION OF LEAN MANUFACTURING PHILOSOPHY BY KAIZEN EVENT: CASE STUDY ON A METALMECHANICAL INDUSTRY

Directory of Open Access Journals (Sweden)

Vinicius Mitsuo Kojima Campos

2016-03-01

Full Text Available The competitive scenario requires organizational strategies increasingly elaborated, creating the need of companies to structure their management models in order to absorb these conflicts generated by competition. The manufacturing area is financially affecting deeply the company's results, thus process improvement comes as the organization's survival guideline, and the rationalization of waste without the need for high investments, shown a great competitive alternative. The application of Kaizen event seeks to measure the benefits generated by the implementation of the philosophy of lean manufacturing, working setup aspects of machinery, the manufacturing process flow, reduced delivery lead-time and inventory process. The Kaizen Blitz was applied in a production cell of stamping and spirt processes. The obtained major improvements have been the reduction of machine setup time, reducing lead-time of item processing, the material flow within the production cell, and creating conditions for a more flexible management of the production schedule.

Application of the Commercial Grade Item (CGI) Dedication Process for Procurement of Nuclear Safety Related Items at Nuclear Power Plant Krsko (NEK)

International Nuclear Information System (INIS)

Heruc, Z.; Pozar, J.

1998-01-01

CGI procurement is a process whereby parts are brought without imposing Appendix B Quality Assurance requirements on the supplier, and than dedicated for use in safety-related applications. The dedication process involves 1) based upon required safety function, an engineering evaluation to identify critical characteristic of the item and specification of acceptance criteria; and 2) quality control activities to ensure the item(s) supplied meets the acceptance criteria specified. CGI Dedication supports the supply of certified components/parts for the plant operation in an environment where the number of nuclear qualified suppliers diminishes. It requires a more active role of the plant personnel, therefore presenting an additional burden on human resources, but at the same time increases the technical KNOW-HOW and improves the confidence of test and inspection data presented in the certificates. Very often it is also cost beneficial. This paper is a continuation to last year presentation of the introduction of this method into NEK's procurement process and presents the current approach and some practical examples. (author)

Social manufacturing

OpenAIRE

Hamalainen, Markko; Karjalainen, Jesse

2017-01-01

New business models harnessing the power of individuals have already revolutionized service industries and digital content production. In this study, we investigate whether a similar phenomenon is taking place in manufacturing industries. We start by conceptually defining two distinct forms of firm-individual collaboration in manufacturing industries: (1) social cloud manufacturing, in which firms outsource manufacturing to individuals, and (2) social platform manufacturing, in which firms pr...

The randomly renewed general item and the randomly inspected item with exponential life distribution

International Nuclear Information System (INIS)

Schneeweiss, W.G.

1979-01-01

For a randomly renewed item the probability distributions of the time to failure and of the duration of down time and the expectations of these random variables are determined. Moreover, it is shown that the same theory applies to randomly checked items with exponential probability distribution of life such as electronic items. The case of periodic renewals is treated as an example. (orig.) [de

The relationships between Lean manufacturing, management accounting and firm performance

DEFF Research Database (Denmark)

Kristensen, Thomas Borup; Nielsen, Henrik; Grasso, Lawrency

2016-01-01

with management accounting practices. Specifically, we document that Lean manufacturing is positively associated with Value Stream Costing, Lean visual controls and, more importantly, measures of labor and materials efficiency. Lean manufacturing is positively related to Lean thinking and both are positively...... associated with operational performance and so are Lean visual controls. We also document that the management accounting practices intervene affecting operational performance and they intervene with Lean thinking as well. Lastly, the relationship between Lean manufacturing and measures of labor and materials......Lean manufacturing has been adopted by numerous western companies as an answer to an increasing competitive environment. Lean manufacturing is seen as an enterprise-wide strategy encompassing a transformation of manufacturing practices, affecting companies’ management accounting practices and...

Specialization and Commonalization in Multi-branded Manufacturing Corporations

DEFF Research Database (Denmark)

Karlsson, Christer; Sköld, Martin

2018-01-01

Purpose: The purpose of this paper is to identify areas and issues for management to consider in balancing specialization and commonalization in large manufacturing corporations with multiple brands from a strategic R&D and manufacturing point of view.Design/methodology/approach Three global...... manufacturing corporations from the automotive sector are used as a strategic sample composing three sequential clinical research projects. The data come from complementary data-gathering methods combining documents and interviews and workshops with top executives, project leaders, platform managers and product...... brand, missing the specific dynamics of large manufacturing corporations with many entities, such as individual products and brands. This paper adds knowledge regarding how to balance synergies from commonalization with important objectives to preserve the specialization and distinctiveness of each...

Disease-specific self-efficacy in spasmodic dysphonia patients.

Science.gov (United States)

Hu, Amanda; Isetti, Derek; Hillel, Allen D; Waugh, Patricia; Comstock, Bryan; Meyer, Tanya K

2013-03-01

Self-efficacy (SE) is an optimistic self-belief that one can perform a novel task. This concept involves empowerment, self-esteem, and adaptation to a stressful situation. SE is a strong predictor of health behaviors. Our objectives were to study SE in spasmodic dysphonia (SD) and to develop a disease-specific SE-SD scale. Prospective study. Academic hospital. Disease-specific SE-SD items were developed with laryngologists, speech pathologists, and SD patients. These items, General SE Scale, Voice Handicap Index-10 (VHI-10), Consensus Auditory Perceptual Evaluation of Voice (CAPE-V), and Hospital Anxiety and Depression Scale (HADS), were administered to SD patients who presented for botulinum toxin injections. One hundred forty-five SD patients (mean age 59.5 ± 13.6 years) had a general SE score (Cronbach's α = 0.894) of 33.4 ± 5.2 out of 40. This was negatively correlated with HADS-A (r = -0.42, P < 0.001) and HADS-D (r = -0.42, P < .001), but not correlated with VHI-10 (r = -0.098, P = .243) and CAPE-V (r = -0.047, P = .57). Factor analysis selected 8 items from the general SE scale and 5 disease-specific SE-SD items to generate a 13-item disease-specific SE-SD scale (Cronbach's α = 0.907). Disease-specific SE-SD score was 42.1 ± 6.9 out of 52 and was negatively correlated with VHI-10 (r = -0.19, P = .005), HADS-A (r = -0.43, P < .001), and HADS-D (r = -0.57, P < .001), but not correlated with CAPE-V (r = -0.024, P = .60). SD patients established on botulinum toxin injections have high degrees of general and disease-specific SE. Patients with higher SE-SD demonstrate lower vocal handicap and lower levels of anxiety and depression. A 13-item disease-specific SE-SD scale has been developed.

Assessing the Impact of IT Competency on Organizational Learning Capability of Indonesian Manufacturing Firms

Directory of Open Access Journals (Sweden)

Alizar Hasan

2010-01-01

Full Text Available This paper attempt to assessing the impact of IT competency on organizational learning capability by using the measurement scale that have been developed by Tippins et al. and Gomes et al. These studies cover a sample of 192 manufacturing firms. IT competencies are classified into three dimensions: IT knowledge, IT operations, and IT objects, and organizational learning capability are classified into four dimensions: Managerial commitment, System perspec-tive, Openness and experimentation, and Knowledge transfer and integration. The result of factor analysis on IT competency and Organizational learning capability show that all items have high loading only on a single factor with ranging from .60 to .84. The findings revealed that IT competency positively and significantly influences the organizational learning capability of Indonesian manufacturing firms.

Understanding Mechanical Design with Respect to Manufacturability

Science.gov (United States)

Mondell, Skyler

2010-01-01

At the NASA Prototype Development Laboratory in Kennedy Space Center, Fl, several projects concerning different areas of mechanical design were undertaken in order to better understand the relationship between mechanical design and manufacturabiIity. The assigned projects pertained specifically to the NASA Space Shuttle, Constellation, and Expendable Launch Vehicle programs. During the work term, mechanical design practices relating to manufacturing processes were learned and utilized in order to obtain an understanding of mechanical design with respect to manufacturability.

Numerosity estimates for attended and unattended items in visual search.

Science.gov (United States)

Kelley, Troy D; Cassenti, Daniel N; Marusich, Laura R; Ghirardelli, Thomas G

2017-07-01

The goal of this research was to examine memories created for the number of items during a visual search task. Participants performed a visual search task for a target defined by a single feature (Experiment 1A), by a conjunction of features (Experiment 1B), or by a specific spatial configuration of features (Experiment 1C). On some trials following the search task, subjects were asked to recall the total number of items in the previous display. In all search types, participants underestimated the total number of items, but the severity of the underestimation varied depending on the efficiency of the search. In three follow-up studies (Experiments 2A, 2B, and 2C) using the same visual stimuli, the participants' only task was to estimate the number of items on each screen. Participants still underestimated the numerosity of the items, although the degree of underestimation was smaller than in the search tasks and did not depend on the type of visual stimuli. In Experiment 3, participants were asked to recall the number of items in a display only once. Subjects still displayed a tendency to underestimate, indicating that the underestimation effects seen in Experiments 1A-1C were not attributable to knowledge of the estimation task. The degree of underestimation depends on the efficiency of the search task, with more severe underestimation in efficient search tasks. This suggests that the lower attentional demands of very efficient searches leads to less encoding of numerosity of the distractor set.

Designing Integrated Product- Service System Solutions in Manufacturing Industries

DEFF Research Database (Denmark)

Costa, Nina; Patrício, Lia; Morelli, Nicola

2015-01-01

Manufacturing firms are increasingly evolving towards the design of integrated product-service solutions but servitization literature does not provide specific guidance on how to design these integrated solutions. Building upon ProductService System (PSS) and Service Design (SD) approaches...... how it brings new insights to manufacturing companies moving to a service, value cocreation perspective....

Additive Manufacturing of Metal Structures at the Micrometer Scale.

Science.gov (United States)

Hirt, Luca; Reiser, Alain; Spolenak, Ralph; Zambelli, Tomaso

2017-05-01

Currently, the focus of additive manufacturing (AM) is shifting from simple prototyping to actual production. One driving factor of this process is the ability of AM to build geometries that are not accessible by subtractive fabrication techniques. While these techniques often call for a geometry that is easiest to manufacture, AM enables the geometry required for best performance to be built by freeing the design process from restrictions imposed by traditional machining. At the micrometer scale, the design limitations of standard fabrication techniques are even more severe. Microscale AM thus holds great potential, as confirmed by the rapid success of commercial micro-stereolithography tools as an enabling technology for a broad range of scientific applications. For metals, however, there is still no established AM solution at small scales. To tackle the limited resolution of standard metal AM methods (a few tens of micrometers at best), various new techniques aimed at the micrometer scale and below are presently under development. Here, we review these recent efforts. Specifically, we feature the techniques of direct ink writing, electrohydrodynamic printing, laser-assisted electrophoretic deposition, laser-induced forward transfer, local electroplating methods, laser-induced photoreduction and focused electron or ion beam induced deposition. Although these methods have proven to facilitate the AM of metals with feature sizes in the range of 0.1-10 µm, they are still in a prototype stage and their potential is not fully explored yet. For instance, comprehensive studies of material availability and material properties are often lacking, yet compulsory for actual applications. We address these items while critically discussing and comparing the potential of current microscale metal AM techniques. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Test manufacture of the canister insert 135

International Nuclear Information System (INIS)

Raiko, H.

2005-10-01

This report describes the insert-manufacturing test of a disposal canister for spent nuclear fuel that was made by Metso Foundries Jyvaeskylae Oy, in June 2004 on contract for Posiva Oy. The test manufacture was a part of the co-operation development programme of encapsulation technology between SKB AB and Posiva Oy. Insert casting was specified according to the current manufacturing specifications of SKB. The canister insert was of BWR-type with integral bottom. This was the second trial manufacture of this type of insert in Finland and, in total, the third test manufacture of insert by Metso Foundries Jyvaeskylae Oy. The result fulfilled all the requirements but the material mechanical properties of the cast material. The measured ultimate strength and elongation at rupture were lower than specified in the upper part of the cast. The reason for this was revealed in the metallurgical investigation of the cast material. The cast contained slag (dross). Avoiding the dross formation will be the most demanding challenge of the forthcoming development of the cast procedure. (orig.)

Development of zirconium alloy tube manufacturing technology

International Nuclear Information System (INIS)

Kim, In Kyu; Park, Chan Hyun; Lee, Seung Hwan; Chung, Sun Kyo

2009-01-01

In late 2004, Korea Nuclear Fuel Company (KNF) launched a government funded joint development program with Westinghouse Electric Co. (WEC) to establish zirconium alloy tube manufacturing technology in Korea. Through this program, KNF and WEC have developed a state of the art facility to manufacture high quality nuclear tubes. KNF performed equipment qualification tests for each manufacturing machine with the support of WEC, and independently carried out product qualification tests for each tube product to be commercially produced. Apart from those tests, characterization test program consisting of specification test and characterization test was developed by KNF and WEC to demonstrate to customers of KNF the quality equivalency of products manufactured by KNF and WEC plants respectively. As part of establishment of performance evaluation technology for zirconium alloy tube in Korea, KNF carried out analyses of materials produced for the characterization test program using the most advanced techniques. Thanks to the accomplishment of the development of zirconium alloy tube manufacturing technology, KNF is expected to acquire positive spin off benefits in terms of technology and economy in the near future

Historical Financial Data - Domestic Automobile Manufacturers

Science.gov (United States)

1979-01-01

A historical financial data base was developed for the four major U.S. automobile manufacturers, focusing on the specific operations associated with production and marketing of automobiles and light trucks. The years subject to analysis were 1967-197...

17 CFR 260.7a-16 - Inclusion of items, differentiation between items and answers, omission of instructions.

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 3 2010-04-01 2010-04-01 false Inclusion of items, differentiation between items and answers, omission of instructions. 260.7a-16 Section 260.7a-16 Commodity and... INDENTURE ACT OF 1939 Formal Requirements § 260.7a-16 Inclusion of items, differentiation between items and...

Biological features produced by additive manufacturing processes using vat photopolymerization method

DEFF Research Database (Denmark)

Davoudinejad, Ali; Mendez Ribo, Macarena; Pedersen, David Bue

2017-01-01

of micro biological features by Additive Manufacturing (AM) processes. The study characterizes the additive manufacturing processes for polymeric micro part productions using the vat photopolymerization method. A specifically designed vat photopolymerization AM machine suitable for precision printing...

The Effects of Test Length and Sample Size on Item Parameters in Item Response Theory

Science.gov (United States)

Sahin, Alper; Anil, Duygu

2017-01-01

This study investigates the effects of sample size and test length on item-parameter estimation in test development utilizing three unidimensional dichotomous models of item response theory (IRT). For this purpose, a real language test comprised of 50 items was administered to 6,288 students. Data from this test was used to obtain data sets of…

Serum Neuron-Specific Enolase, Biogenic Amino-Acids and Neurobehavioral Function in Lead-Exposed Workers from Lead-Acid Battery Manufacturing Process

Directory of Open Access Journals (Sweden)

K Ravibabu

2015-01-01

Full Text Available Background: The interaction between serum neuron-specific enolase (NSE, biogenic amino-acids and neurobehavioral function with blood lead levels in workers exposed to lead form lead-acid battery manufacturing process was not studied. Objective: To evaluate serum NSE and biogenic amino-acids (dopamine and serotonin levels, and neurobehavioral performance among workers exposed to lead from lead-acid storage battery plant, and its relation with blood lead levels (BLLs. Methods: In a cross-sectional study, we performed biochemical and neurobehavioral function tests on 146 workers exposed to lead from lead-acid battery manufacturing process. BLLs were assessed by an atomic absorption spectrophotometer. Serum NSE, dopamine and serotonin were measured by ELISA. Neurobehavioral functions were assessed by CDC-recommended tests—simple reaction time (SRT, symbol digit substitution test (SDST, and serial digit learning test (SDLT. Results: There was a significant correlation (r 0.199, p<0.05 between SDST and BLL. SDLT and SRT had also a significant positive correlation (r 0.238, p<0.01. NSE had a negative correlation (r –0.194, p<0.05 with serotonin level. Multiple linear regression analysis revealed that both SRT and SDST had positive significant associations with BLL. SRT also had a positive significant association with age. Conclusion: Serum NSE cannot be used as a marker for BLL. The only domain of neurobehavioral function tests that is affected by increased BLL in workers of lead-acid battery manufacturing process is that of the “attention and perception” (SDST.

Effect of study context on item recollection.

Science.gov (United States)

Skinner, Erin I; Fernandes, Myra A

2010-07-01

We examined how visual context information provided during encoding, and unrelated to the target word, affected later recollection for words presented alone using a remember-know paradigm. Experiments 1A and 1B showed that participants had better overall memory-specifically, recollection-for words studied with pictures of intact faces than for words studied with pictures of scrambled or inverted faces. Experiment 2 replicated these results and showed that recollection was higher for words studied with pictures of faces than when no image accompanied the study word. In Experiment 3 participants showed equivalent memory for words studied with unique faces as for those studied with a repeatedly presented face. Results suggest that recollection benefits when visual context information high in meaningful content accompanies study words and that this benefit is not related to the uniqueness of the context. We suggest that participants use elaborative processes to integrate item and meaningful contexts into ensemble information, improving subsequent item recollection.

Approximation Preserving Reductions among Item Pricing Problems

Science.gov (United States)

Hamane, Ryoso; Itoh, Toshiya; Tomita, Kouhei

When a store sells items to customers, the store wishes to determine the prices of the items to maximize its profit. Intuitively, if the store sells the items with low (resp. high) prices, the customers buy more (resp. less) items, which provides less profit to the store. So it would be hard for the store to decide the prices of items. Assume that the store has a set V of n items and there is a set E of m customers who wish to buy those items, and also assume that each item i ∈ V has the production cost di and each customer ej ∈ E has the valuation vj on the bundle ej ⊆ V of items. When the store sells an item i ∈ V at the price ri, the profit for the item i is pi = ri - di. The goal of the store is to decide the price of each item to maximize its total profit. We refer to this maximization problem as the item pricing problem. In most of the previous works, the item pricing problem was considered under the assumption that pi ≥ 0 for each i ∈ V, however, Balcan, et al. [In Proc. of WINE, LNCS 4858, 2007] introduced the notion of “loss-leader, ” and showed that the seller can get more total profit in the case that pi < 0 is allowed than in the case that pi < 0 is not allowed. In this paper, we derive approximation preserving reductions among several item pricing problems and show that all of them have algorithms with good approximation ratio.

Differential item functioning analysis with ordinal logistic regression techniques. DIFdetect and difwithpar.

Science.gov (United States)

Crane, Paul K; Gibbons, Laura E; Jolley, Lance; van Belle, Gerald

2006-11-01

We present an ordinal logistic regression model for identification of items with differential item functioning (DIF) and apply this model to a Mini-Mental State Examination (MMSE) dataset. We employ item response theory ability estimation in our models. Three nested ordinal logistic regression models are applied to each item. Model testing begins with examination of the statistical significance of the interaction term between ability and the group indicator, consistent with nonuniform DIF. Then we turn our attention to the coefficient of the ability term in models with and without the group term. If including the group term has a marked effect on that coefficient, we declare that it has uniform DIF. We examined DIF related to language of test administration in addition to self-reported race, Hispanic ethnicity, age, years of education, and sex. We used PARSCALE for IRT analyses and STATA for ordinal logistic regression approaches. We used an iterative technique for adjusting IRT ability estimates on the basis of DIF findings. Five items were found to have DIF related to language. These same items also had DIF related to other covariates. The ordinal logistic regression approach to DIF detection, when combined with IRT ability estimates, provides a reasonable alternative for DIF detection. There appear to be several items with significant DIF related to language of test administration in the MMSE. More attention needs to be paid to the specific criteria used to determine whether an item has DIF, not just the technique used to identify DIF.

Precision manufacturing

CERN Document Server

Dornfeld, David

2008-01-01

Today there is a high demand for high-precision products. The manufacturing processes are now highly sophisticated and derive from a specialized genre called precision engineering. Precision Manufacturing provides an introduction to precision engineering and manufacturing with an emphasis on the design and performance of precision machines and machine tools, metrology, tooling elements, machine structures, sources of error, precision machining processes and precision process planning. As well as discussing the critical role precision machine design for manufacturing has had in technological developments over the last few hundred years. In addition, the influence of sustainable manufacturing requirements in precision processes is introduced. Drawing upon years of practical experience and using numerous examples and illustrative applications, David Dornfeld and Dae-Eun Lee cover precision manufacturing as it applies to: The importance of measurement and metrology in the context of Precision Manufacturing. Th...

Which Statistic Should Be Used to Detect Item Preknowledge When the Set of Compromised Items Is Known?

Science.gov (United States)

Sinharay, Sandip

2017-09-01

Benefiting from item preknowledge is a major type of fraudulent behavior during educational assessments. Belov suggested the posterior shift statistic for detection of item preknowledge and showed its performance to be better on average than that of seven other statistics for detection of item preknowledge for a known set of compromised items. Sinharay suggested a statistic based on the likelihood ratio test for detection of item preknowledge; the advantage of the statistic is that its null distribution is known. Results from simulated and real data and adaptive and nonadaptive tests are used to demonstrate that the Type I error rate and power of the statistic based on the likelihood ratio test are very similar to those of the posterior shift statistic. Thus, the statistic based on the likelihood ratio test appears promising in detecting item preknowledge when the set of compromised items is known.

An emotional functioning item bank of 24 items for computerized adaptive testing (CAT) was established

DEFF Research Database (Denmark)

Petersen, Morten Aa.; Gamper, Eva-Maria; Costantini, Anna

2016-01-01

of the widely used EORTC Quality of Life questionnaire (QLQ-C30). STUDY DESIGN AND SETTING: On the basis of literature search and evaluations by international samples of experts and cancer patients, 38 candidate items were developed. The psychometric properties of the items were evaluated in a large...... international sample of cancer patients. This included evaluations of dimensionality, item response theory (IRT) model fit, differential item functioning (DIF), and of measurement precision/statistical power. RESULTS: Responses were obtained from 1,023 cancer patients from four countries. The evaluations showed...... that 24 items could be included in a unidimensional IRT model. DIF did not seem to have any significant impact on the estimation of EF. Evaluations indicated that the CAT measure may reduce sample size requirements by up to 50% compared to the QLQ-C30 EF scale without reducing power. CONCLUSION...

Factoring handedness data: I. Item analysis.

Science.gov (United States)

Messinger, H B; Messinger, M I

1995-12-01

Recently in this journal Peters and Murphy challenged the validity of factor analyses done on bimodal handedness data, suggesting instead that right- and left-handers be studied separately. But bimodality may be avoidable if attention is paid to Oldfield's questionnaire format and instructions for the subjects. Two characteristics appear crucial: a two-column LEFT-RIGHT format for the body of the instrument and what we call Oldfield's Admonition: not to indicate strong preference for handedness item, such as write, unless "... the preference is so strong that you would never try to use the other hand unless absolutely forced to...". Attaining unimodality of an item distribution would seem to overcome the objections of Peters and Murphy. In a 1984 survey in Boston we used Oldfield's ten-item questionnaire exactly as published. This produced unimodal item distributions. With reflection of the five-point item scale and a logarithmic transformation, we achieved a degree of normalization for the items. Two surveys elsewhere based on Oldfield's 20-item list but with changes in the questionnaire format and the instructions, yielded markedly different item distributions with peaks at each extreme and sometimes in the middle as well.

Decommissioning plan depleted uranium manufacturing facility

International Nuclear Information System (INIS)

Bernhardt, D.E.; Pittman, J.D.; Prewett, S.V.

1987-01-01

Aerojet Ordnance Tennessee, Inc. (Aerojet) is decommissioning its California depleted uranium (DU) manufacturing facility. Aerojet has conducted manufacturing and research and development activities at the facility since 1977 under a State of California Source Materials License. The decontamination is being performed by a contractor selector for technical competence through competitive bid. Since the facility will be released for uncontrolled use it will be decontaminated to levels as low as reasonably achievable (ALARA). In order to fully apply the principles of ALARA, and ensure the decontamination is in full compliance with appropriate guides, Aerojet has retained Rogers and Associaties Engineering Corporation (RAE) to assist in the decommissioning. RAE has assisted in characterizing the facility and preparing contract bid documents and technical specifications to obtain a qualified decontamination contractor. RAE will monitor the decontamination work effort to assure the contractor's performance complies with the contract specifications and the decontamination plan. The specifications require a thorough cleaning and decontamination of the facility, not just sufficient cleaning to meet the numeric cleanup criteria

Item Modeling Concept Based on Multimedia Authoring

Directory of Open Access Journals (Sweden)

Janez Stergar

2008-09-01

Full Text Available In this paper a modern item design framework for computer based assessment based on Flash authoring environment will be introduced. Question design will be discussed as well as the multimedia authoring environment used for item modeling emphasized. Item type templates are a structured means of collecting and storing item information that can be used to improve the efficiency and security of the innovative item design process. Templates can modernize the item design, enhance and speed up the development process. Along with content creation, multimedia has vast potential for use in innovative testing. The introduced item design template is based on taxonomy of innovative items which have great potential for expanding the content areas and construct coverage of an assessment. The presented item design approach is based on GUI's – one for question design based on implemented item design templates and one for user interaction tracking/retrieval. The concept of user interfaces based on Flash technology will be discussed as well as implementation of the innovative approach of the item design forms with multimedia authoring. Also an innovative method for user interaction storage/retrieval based on PHP extending Flash capabilities in the proposed framework will be introduced.

The medial temporal lobes distinguish between within-item and item-context relations during autobiographical memory retrieval.

Science.gov (United States)

Sheldon, Signy; Levine, Brian

2015-12-01

During autobiographical memory retrieval, the medial temporal lobes (MTL) relate together multiple event elements, including object (within-item relations) and context (item-context relations) information, to create a cohesive memory. There is consistent support for a functional specialization within the MTL according to these relational processes, much of which comes from recognition memory experiments. In this study, we compared brain activation patterns associated with retrieving within-item relations (i.e., associating conceptual and sensory-perceptual object features) and item-context relations (i.e., spatial relations among objects) with respect to naturalistic autobiographical retrieval. We developed a novel paradigm that cued participants to retrieve information about past autobiographical events, non-episodic within-item relations, and non-episodic item-context relations with the perceptuomotor aspects of retrieval equated across these conditions. We used multivariate analysis techniques to extract common and distinct patterns of activity among these conditions within the MTL and across the whole brain, both in terms of spatial and temporal patterns of activity. The anterior MTL (perirhinal cortex and anterior hippocampus) was preferentially recruited for generating within-item relations later in retrieval whereas the posterior MTL (posterior parahippocampal cortex and posterior hippocampus) was preferentially recruited for generating item-context relations across the retrieval phase. These findings provide novel evidence for functional specialization within the MTL with respect to naturalistic memory retrieval. © 2015 Wiley Periodicals, Inc.

Service orientation in holonic and multi-agent manufacturing

CERN Document Server

Thomas, André; Trentesaux, Damien

2015-01-01

This volume gathers the peer reviewed papers presented at the 4th edition of the International Workshop “Service Orientation in Holonic and Multi-agent Manufacturing – SOHOMA’14” organized and hosted on November 5-6, 2014 by the University of Lorraine, France in collaboration with the CIMR Research Centre of the University Politehnica of Bucharest and the TEMPO Laboratory of the University of Valenciennes and Hainaut-Cambrésis.   The book is structured in six parts, each one covering a specific research line which represents a trend in future manufacturing: (1) Holonic and Agent-based Industrial Automation Systems; (2) Service-oriented Management and Control of Manufacturing Systems; (3) Distributed Modelling for Safety and Security in Industrial Systems; (4) Complexity, Big Data and Virtualization in Computing-oriented Manufacturing; (5) Adaptive, Bio-inspired and Self-organizing Multi-Agent Systems for Manufacturing, and (6) Physical Internet Simulation, Modelling and Control.   There is a clear ...

Differential item functioning of the patient-reported outcomes information system (PROMIS®) pain interference item bank by language (Spanish versus English).

Science.gov (United States)

Paz, Sylvia H; Spritzer, Karen L; Reise, Steven P; Hays, Ron D

2017-06-01

About 70% of Latinos, 5 years old or older, in the United States speak Spanish at home. Measurement equivalence of the PROMIS ® pain interference (PI) item bank by language of administration (English versus Spanish) has not been evaluated. A sample of 527 adult Spanish-speaking Latinos completed the Spanish version of the 41-item PROMIS ® pain interference item bank. We evaluate dimensionality, monotonicity and local independence of the Spanish-language items. Then we evaluate differential item functioning (DIF) using ordinal logistic regression with item response theory scores estimated from DIF-free "anchor" items. One of the 41 items in the Spanish version of the PROMIS ® PI item bank was identified as having significant uniform DIF. English- and Spanish-speaking subjects with the same level of pain interference responded differently to 1 of the 41 items in the PROMIS ® PI item bank. This item was not retained due to proprietary issues. The original English language item parameters can be used when estimating PROMIS ® PI scores.

A proposal of ITER vacuum vessel fabrication specification and results of the full-scale partial mock-up test

Energy Technology Data Exchange (ETDEWEB)

Nakahira, Masataka; Takeda, Nobukazu; Onozuka, Masanori [Japan Atomic Energy Agency (Japan); Kakudate, Satoshi [Mitsubishi Heavy Industries, Ltd. (Japan)

2007-07-01

The structure and fabrication methods of the ITER vacuum vessel have been investigated and defined by the ITER international team. However, some of the current specifications are very difficult to be achieved from the manufacturing point of view and will lead to cost increase. In the mock-up fabrication, it is planned to conduct the following items: 1. Feasibility of the Japanese proposed VV structure and fabrication methods and the applicability to the ITER are to be confirmed; 2. Assembly procedure and inspection procedure are to be confirmed; 3. Manufacturing tolerances are to be assessed; 4. Manufacturing schedule is to be assessed. This report summarizes the Japanese proposed specification of the VV mock-up describing differences between the ITER supplied design. General scope of the mock-up fabrication and the detailed dimensions are also shown. In the VV fabrication, several types of weld joint configuration will be used. This report shows the joint configurations proposed by Japan to be used for the inner shell connection, the rib-to-shell connection and outer shell connection, and the housing-to-shell connection, respectively. Non-destructive testing considered to be applied to each joint configuration is also presented. A series of the fabrication and assembly procedures for the mock-up are presented in this report, together with candidates of welding configurations. Finally, the report summarizes the results of mock-up fabrication, including results of nondestructive examination of weld lines, obtained welding deformation and issues revealed from the fabrication experience. (orig.)

Globes and Teaching Aids Manufactured by Jan Felkl Company for the Polish Market

Directory of Open Access Journals (Sweden)

Malgorzata Taborska

2016-05-01

Full Text Available Jan Felkl company from Roztoky (Roztok near Prague manufactured globes in seventeen language versions, since 1861 also in Polish language. The company was active until 1952, but it ceased to manufacture Polish-language globes as early as in 1914. In the aftermath of the First World War, and with the development of printing business, the demand for Czech globes shrank. It is difficult to estimate the overall output of Polish- language globes manufactured by Felkl’s company throughout the 53 years it operated. From catalogues and the surviving globes we know that terrestrial globes in six sizes, folding globes in two sizes, celestial globes (probably in four sizes, as well as telluria, lunaria and planetaria were manufactured for the Polish market. It is difficult to decide how many editions of individual types of globes were issued. Polish names were compiled by Franciszek Waligórski (one globe and Mirosław Suchecki. Only 28 globes have survived to this day, including one celestial globe. Most of them are globes of an 8-inch diameter, approved by the Austrian ministries as teaching aids for schools. Nearly half of the surviving globes date from the years 1894–1914. Only ten items are in museums.

A strategy for optimizing item-pool management

NARCIS (Netherlands)

Ariel, A.; van der Linden, Willem J.; Veldkamp, Bernard P.

2006-01-01

Item-pool management requires a balancing act between the input of new items into the pool and the output of tests assembled from it. A strategy for optimizing item-pool management is presented that is based on the idea of a periodic update of an optimal blueprint for the item pool to tune item

Manufacturing: SiC Power Electronics for Variable Frequency Motor Drives

Energy Technology Data Exchange (ETDEWEB)

Horowitz, Kelsey A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Bench Reese, Samantha R [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Remo, Timothy W [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2017-08-15

This brochure, published as an annual research highlight of the Clean Energy Manufacturing Analysis Center (CEMAC), summarizes CEMAC analysis of silicon carbide (SiC) power electronics for variable frequency motor drives. The key finding presented is that variations in manufacturing expertise, yields, and access to existing facilities impact regional costs and manufacturing location decisions for SiC ingots, wafers, chips, and power modules more than do core country-specific factors such as labor and electricity costs.

Sockets Manufactured by CAD/CAM Method Have Positive Effects on the Quality of Life of Patients With Transtibial Amputation.

Science.gov (United States)

Karakoç, Mehmet; Batmaz, İbrahim; Sariyildiz, Mustafa Akif; Yazmalar, Levent; Aydin, Abdülkadir; Em, Serda

2017-08-01

Patients with amputation need prosthesis to comfortably move around. One of the most important parts of a good prosthesis is the socket. Currently, the most commonly used method is the traditional socket manufacturing method, which involves manual work; however, computer-aided design/computer-aided manufacturing (CAD/CAM) is also being used in the recent years. The present study aimed to investigate the effects of sockets manufactured by traditional and CAD/CAM method on clinical characteristics and quality of life of patients with transtibial amputation. The study included 72 patients with transtibial amputation using prosthesis, 36 of whom had CAD/CAM prosthetic sockets (group 1) and 36 had traditional prosthetic sockets (group 2). Amputation reason, prosthesis lifetime, walking time and distance with prosthesis, pain-free walking time with prosthesis, production time of the prosthesis, and adaptation time to the prosthesis were questioned. Quality of life was assessed using the 36-item Short Form Health Survey questionnaire and the Trinity Amputation and Prosthesis Experience Scales. Walking time and distance and pain-free walking time with prosthesis were significantly better in group 1 than those in group 2. Furthermore, the prosthesis was applied in a significantly shorter time, and socket adaptation time was significantly shorter in group 1. Except emotional role limitation, all 36-item Short Form Healthy Survey questionnaire parameters were significantly better in group 1 than in group 2. Trinity Amputation and Prosthesis Experience Scales activity limitation scores of group 1 were lower, and Trinity Amputation and Prosthesis Experience Scales satisfaction with the prosthesis scores were higher than those in group 2. Our study demonstrated that the sockets manufactured by CAD/CAM methods yield better outcomes in quality of life of patients with transtibial amputation than the sockets manufactured by the traditional method.

Manufacturing process optimization of nuclear fuel guide tube using HANA alloys

International Nuclear Information System (INIS)

Jeong, Yong Hwan; Park, S. Y.; Choi, B. K.; Park, J. Y.; Kim, H. G.; Jeong, Y. I.; Park, D. J.; Lim, J. K.

2010-08-01

From this project, the advanced manufacturing parameters which were contained of heat-treatment, reduction rate, and new process (2 step) were considered to increase the guide tube performance of HANA material. It was obtained that the strength and corrosion resistance of HANA material were improved by applying the improve manufacturing parameters when compared to the commercial guide tube material. · Manufacturing parameter study to increase mechanical property -Tensile strength increase of 30% by manufacturing parameter setup when compared to the guide tube specification · Manufacturing parameter study to decrease irradiation growth -Theoretical study of the texture effect on sample specimens related to the irradiation growth · Manufacturing parameter study to increase corrosion resistance -Corrosion resistance increase of 30% by manufacturing parameter setup when compared to the commercial guide tube

Manufacturing network evolution

DEFF Research Database (Denmark)

Yang, Cheng; Farooq, Sami; Johansen, John

2011-01-01

Purpose – This paper examines the effect of changes at the manufacturing plant level on other plants in the manufacturing network and also investigates the role of manufacturing plants on the evolution of a manufacturing network. Design/methodology/approach –The research questions are developed...... different manufacturing plants in the network and their impact on network transformation. Findings – The paper highlights the dominant role of manufacturing plants in the continuously changing shape of a manufacturing network. The paper demonstrates that a product or process change at one manufacturing...... by identifying the gaps in the reviewed literature. The paper is based on three case studies undertaken in Danish manufacturing companies to explore in detail their manufacturing plants and networks. The cases provide a sound basis for developing the research questions and explaining the interaction between...

Development of the Oxford Participation and Activities Questionnaire: constructing an item pool

Directory of Open Access Journals (Sweden)

Kelly L

2015-05-01

Full Text Available Laura Kelly, Crispin Jenkinson, Sarah Dummett, Jill Dawson, Ray Fitzpatrick, David Morley Health Services Research Unit, Nuffield Department of Population Health, University of Oxford, Oxford, UK Purpose: The Oxford Participation and Activities Questionnaire is a patient-reported outcome measure in development that is grounded on the World Health Organization International Classification of Functioning, Disability, and Health (ICF. The study reported here aimed to inform and generate an item pool for the new measure, which is specifically designed for the assessment of participation and activity in patients experiencing a range of health conditions. Methods: Items were informed through in-depth interviews conducted with 37 participants spanning a range of conditions. Interviews aimed to identify how their condition impacted their ability to participate in meaningful activities. Conditions included arthritis, cancer, chronic back pain, diabetes, motor neuron disease, multiple sclerosis, Parkinson's disease, and spinal cord injury. Transcripts were analyzed using the framework method. Statements relating to ICF themes were recast as questionnaire items and shown for review to an expert panel. Cognitive debrief interviews (n=13 were used to assess items for face and content validity. Results: ICF themes relevant to activities and participation in everyday life were explored, and a total of 222 items formed the initial item pool. This item pool was refined by the research team and 28 generic items were mapped onto all nine chapters of the ICF construct, detailing activity and participation. Cognitive interviewing confirmed the questionnaire instructions, items, and response options were acceptable to participants. Conclusion: Using a clear conceptual basis to inform item generation, 28 items have been identified as suitable to undergo further psychometric testing. A large-scale postal survey will follow in order to refine the instrument further and

Item response theory - A first approach

Science.gov (United States)

Nunes, Sandra; Oliveira, Teresa; Oliveira, Amílcar

2017-07-01

The Item Response Theory (IRT) has become one of the most popular scoring frameworks for measurement data, frequently used in computerized adaptive testing, cognitively diagnostic assessment and test equating. According to Andrade et al. (2000), IRT can be defined as a set of mathematical models (Item Response Models - IRM) constructed to represent the probability of an individual giving the right answer to an item of a particular test. The number of Item Responsible Models available to measurement analysis has increased considerably in the last fifteen years due to increasing computer power and due to a demand for accuracy and more meaningful inferences grounded in complex data. The developments in modeling with Item Response Theory were related with developments in estimation theory, most remarkably Bayesian estimation with Markov chain Monte Carlo algorithms (Patz & Junker, 1999). The popularity of Item Response Theory has also implied numerous overviews in books and journals, and many connections between IRT and other statistical estimation procedures, such as factor analysis and structural equation modeling, have been made repeatedly (Van der Lindem & Hambleton, 1997). As stated before the Item Response Theory covers a variety of measurement models, ranging from basic one-dimensional models for dichotomously and polytomously scored items and their multidimensional analogues to models that incorporate information about cognitive sub-processes which influence the overall item response process. The aim of this work is to introduce the main concepts associated with one-dimensional models of Item Response Theory, to specify the logistic models with one, two and three parameters, to discuss some properties of these models and to present the main estimation procedures.

Structure and relationships within global manufacturing virtual networks

Directory of Open Access Journals (Sweden)

José Ramón Vilana

2009-04-01

Full Text Available Global Manufacturing Virtual Networks (GMVNs are dynamically changing organizations formed by Original Equipment Manufacturers (OEMs, Contract Manufacturers (CMs, turn-key and component suppliers, R+D centres and distributors. These networks establish a new type of vertical and horizontal relations between independent companies or even competitors where it is not needed to maintain internal manufacturing resources but to manage and share the network resources. The fluid relations that exist within the GMVNs allow them a very permeable organization easy to connect and disconnect from one to each other as well as to choose a set of partners with specific attributes. The result is a highly flexible system characterized by low barriers to entry and exit, geographic flexibility, low costs, rapid technological diffusion, high diversification through contract manufacturers and exceptional economies of scale. Anyhow, there are three major drawbacks in the GMVNs that should be considered at the beginning of this type of collaborations: 1 the risk of contract manufacturers to develop their own end-products in competition with their customers; 2 the technology transfer between competitors OEMs through other members of the GMVN and 3 the lose of process expertise by the OEMs the more they outsource manufacturing processes to the network.

Investigating Separate and Concurrent Approaches for Item Parameter Drift in 3PL Item Response Theory Equating

Science.gov (United States)

Arce-Ferrer, Alvaro J.; Bulut, Okan

2017-01-01

This study examines separate and concurrent approaches to combine the detection of item parameter drift (IPD) and the estimation of scale transformation coefficients in the context of the common item nonequivalent groups design with the three-parameter item response theory equating. The study uses real and synthetic data sets to compare the two…

FIM-Minimum Data Set Motor Item Bank: Short Forms Development and Precision Comparison in Veterans.

Science.gov (United States)

Li, Chih-Ying; Romero, Sergio; Simpson, Annie N; Bonilha, Heather S; Simpson, Kit N; Hong, Ickpyo; Velozo, Craig A

2018-03-01

To improve the practical use of the short forms (SFs) developed from the item bank, we compared the measurement precision of the 4- and 8-item SFs generated from a motor item bank composed of the FIM and the Minimum Data Set (MDS). The FIM-MDS motor item bank allowed scores generated from different instruments to be co-calibrated. The 4- and 8-item SFs were developed based on Rasch analysis procedures. This article compared person strata, ceiling/floor effects, and test SE plots for each administration form and examined 95% confidence interval error bands of anchored person measures with the corresponding SFs. We used 0.3 SE as a criterion to reflect a reliability level of .90. Veterans' inpatient rehabilitation facilities and community living centers. Veterans (N=2500) who had both FIM and the MDS data within 6 days during 2008 through 2010. Not applicable. Four- and 8-item SFs of FIM, MDS, and FIM-MDS motor item bank. Six SFs were generated with 4 and 8 items across a range of difficulty levels from the FIM-MDS motor item bank. The three 8-item SFs all had higher correlations with the item bank (r=.82-.95), higher person strata, and less test error than the corresponding 4-item SFs (r=.80-.90). The three 4-item SFs did not meet the criteria of SE bank composed of existing instruments across the continuum of care in veterans. We also found that the number of items, not test specificity, determines the precision of the instrument. Copyright © 2017 American Congress of Rehabilitation Medicine. All rights reserved.

Investigating domain-general short-term memory for order versus specific item memory in developmental dyslexia

OpenAIRE

Hachmann, Wibke Maria

2012-01-01

Recent findings suggest that people with dyslexia experience difficulties with the learning of serial order information during the transition from short- to long-term memory. At the same time, models of short-term memory increasingly incorporate a distinction of order and item processing. This work aims to investigate whether serial order processing deficiencies in dyslexia can be traced back to a selective impairment of short-term memory for serial order, and whether this impairment also aff...

Redefining diagnostic symptoms of depression using Rasch analysis: testing an item bank suitable for DSM-V and computer adaptive testing.

Science.gov (United States)

Mitchell, Alex J; Smith, Adam B; Al-salihy, Zerak; Rahim, Twana A; Mahmud, Mahmud Q; Muhyaldin, Asma S

2011-10-01

We aimed to redefine the optimal self-report symptoms of depression suitable for creation of an item bank that could be used in computer adaptive testing or to develop a simplified screening tool for DSM-V. Four hundred subjects (200 patients with primary depression and 200 non-depressed subjects), living in Iraqi Kurdistan were interviewed. The Mini International Neuropsychiatric Interview (MINI) was used to define the presence of major depression (DSM-IV criteria). We examined symptoms of depression using four well-known scales delivered in Kurdish. The Partial Credit Model was applied to each instrument. Common-item equating was subsequently used to create an item bank and differential item functioning (DIF) explored for known subgroups. A symptom level Rasch analysis reduced the original 45 items to 24 items of the original after the exclusion of 21 misfitting items. A further six items (CESD13 and CESD17, HADS-D4, HADS-D5 and HADS-D7, and CDSS3 and CDSS4) were removed due to misfit as the items were added together to form the item bank, and two items were subsequently removed following the DIF analysis by diagnosis (CESD20 and CDSS9, both of which were harder to endorse for women). Therefore the remaining optimal item bank consisted of 17 items and produced an area under the curve (AUC) of 0.987. Using a bank restricted to the optimal nine items revealed only minor loss of accuracy (AUC = 0.989, sensitivity 96%, specificity 95%). Finally, when restricted to only four items accuracy was still high (AUC was still 0.976; sensitivity 93%, specificity 96%). An item bank of 17 items may be useful in computer adaptive testing and nine or even four items may be used to develop a simplified screening tool for DSM-V major depressive disorder (MDD). Further examination of this item bank should be conducted in different cultural settings.

Current manufacturing processes of drug-eluting sutures.

Science.gov (United States)

Champeau, Mathilde; Thomassin, Jean-Michel; Tassaing, Thierry; Jérôme, Christine

2017-11-01

Drug-eluting sutures represent the next generation of surgical sutures since they fulfill their mechanical functions but also deliver the drug in their vicinity after implantation. These implants are produced by a variety of manufacturing processes. Drug-eluting sutures represent the next generation of surgical sutures since they fulfill their mechanical functions but also deliver the drug in their vicinity after implantation. These implants are produced by a variety of manufacturing processes. Two general approaches can be followed: (i) the ones that add the API into the material during the manufacturing process of the suture and (ii) the ones that load the API to an already manufactured suture. Areas covered: This review provides an overview of the current manufacturing processes for drug-eluting suture production and discusses their benefits and drawbacks depending on the type of drugs. The mechanical properties and the drug delivery profile of drug-eluting sutures are highlighted since these implants must fulfill both criteria. Expert opinion: For limited drug contents, melt extrusion and electrospinning are the emerging processes since the drug is added during the suture manufacture process. Advantageously, the drug release profile can be tuned by controlling the processing parameters specific to each process and the composition of the drug-containing polymer. If high drug content is targeted, the coating or grafting of a drug layer on a pre-manufactured suture allows for preservation of the tensile strength requirements of the suture.

Analysis of differential item functioning in the depression item bank from the Patient Reported Outcome Measurement Information System (PROMIS: An item response theory approach

Directory of Open Access Journals (Sweden)

JOSEPH P. EIMICKE

2009-06-01

Full Text Available The aims of this paper are to present findings related to differential item functioning (DIF in the Patient Reported Outcome Measurement Information System (PROMIS depression item bank, and to discuss potential threats to the validity of results from studies of DIF. The 32 depression items studied were modified from several widely used instruments. DIF analyses of gender, age and education were performed using a sample of 735 individuals recruited by a survey polling firm. DIF hypotheses were generated by asking content experts to indicate whether or not they expected DIF to be present, and the direction of the DIF with respect to the studied comparison groups. Primary analyses were conducted using the graded item response model (for polytomous, ordered response category data with likelihood ratio tests of DIF, accompanied by magnitude measures. Sensitivity analyses were performed using other item response models and approaches to DIF detection. Despite some caveats, the items that are recommended for exclusion or for separate calibration were "I felt like crying" and "I had trouble enjoying things that I used to enjoy." The item, "I felt I had no energy," was also flagged as evidencing DIF, and recommended for additional review. On the one hand, false DIF detection (Type 1 error was controlled to the extent possible by ensuring model fit and purification. On the other hand, power for DIF detection might have been compromised by several factors, including sparse data and small sample sizes. Nonetheless, practical and not just statistical significance should be considered. In this case the overall magnitude and impact of DIF was small for the groups studied, although impact was relatively large for some individuals.

Center for Advanced Materials Manufacturing | College of Engineering &

Science.gov (United States)

generation, transmission and purification; biomedical applications; green manufacturing techniques, and finally materials used for national defense by the Navy, Air Force, and Army. Specific areas of research

Implementation of hierarchical design for manufacture rules in manufacturing processes

OpenAIRE

Parvez, Masud

2008-01-01

In order to shorten the product development cycle time, minimise overall cost and smooth transition into production, early consideration of manufacturing processes is important. Design for Manufacture (DFM) is the practice of designing products with manufacturing issues using an intelligent system, which translates 3D solid models into manufacturable features. Many existing and potential applications, particularly in the field of manufacturing, require various aspects of features technology. ...

76 FR 60474 - Commercial Item Handbook

Science.gov (United States)

2011-09-29

... DEPARTMENT OF DEFENSE Defense Acquisition Regulations System Commercial Item Handbook AGENCY.... SUMMARY: DoD has updated its Commercial Item Handbook. The purpose of the Handbook is to help acquisition personnel develop sound business strategies for procuring commercial items. DoD is seeking industry input on...

Calorie changes in chain restaurant menu items: implications for obesity and evaluations of menu labeling.

Science.gov (United States)

Bleich, Sara N; Wolfson, Julia A; Jarlenski, Marian P

2015-01-01

Supply-side reductions to the calories in chain restaurants are a possible benefit of upcoming menu labeling requirements. To describe trends in calories available in large U.S. restaurants. Data were obtained from the MenuStat project, a census of menu items in 66 of the 100 largest U.S. restaurant chains, for 2012 and 2013 (N=19,417 items). Generalized linear models were used to calculate (1) the mean change in calories from 2012 to 2013, among items on the menu in both years; and (2) the difference in mean calories, comparing newly introduced items to those on the menu in 2012 only (overall and between core versus non-core items). Data were analyzed in 2014. Mean calories among items on menus in both 2012 and 2013 did not change. Large restaurant chains in the U.S. have recently had overall declines in calories in newly introduced menu items (-56 calories, 12% decline). These declines were concentrated mainly in new main course items (-67 calories, 10% decline). New beverage (-26 calories, 8% decline) and children's (-46 calories, 20% decline) items also had fewer mean calories. Among chain restaurants with a specific focus (e.g., burgers), average calories in new menu items not core to the business declined more than calories in core menu items. Large chain restaurants significantly reduced the number of calories in newly introduced menu items. Supply-side changes to the calories in chain restaurants may have a significant impact on obesity prevention. Copyright © 2015 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

Composites Manufacturing Education and Technology Facility Expedites Manufacturing Innovation

Energy Technology Data Exchange (ETDEWEB)

2017-01-01

The Composites Manufacturing Education and Technology facility (CoMET) at the National Wind Technology Center at the National Renewable Energy Laboratory (NREL) paves the way for innovative wind turbine components and accelerated manufacturing. Available for use by industry partners and university researchers, the 10,000-square-foot facility expands NREL's composite manufacturing research capabilities by enabling researchers to design, prototype, and test composite wind turbine blades and other components -- and then manufacture them onsite. Designed to work in conjunction with NREL's design, analysis, and structural testing capabilities, the CoMET facility expedites manufacturing innovation.

Manufacturing strategy issues in selected Indian manufacturing industry

Directory of Open Access Journals (Sweden)

Mahender Singh

2013-03-01

Full Text Available This paper presents some findings of Indian manufacturing sectors viz. automobile (especially two-wheeler, tractor and general manufacturing industry. Various manufacturing strategy issues such as competitive priorities, improvement activities, and performance measures, have been identified and assessed in Indian context. Sector wise comparison of competitive priorities, improvement activities i.e. advanced manufacturing technology (AMT, integrated information systems (IIS, and advanced management systems (AMS, and performance measure, is provided. Our results showed that most of the Indian companies are still emphasizing on quality. However, automobile sector has set to compete globally with high innovation rate, faster new product development, and continuous improvement. It is also observed that Indian companies are investing more in AMS as compared to IIS and AMT. Manufacturing competence index is also computed for each sector.

A leukocyte activation test identifies food items which induce release of DNA by innate immune peripheral blood leucocytes.

Science.gov (United States)

Garcia-Martinez, Irma; Weiss, Theresa R; Yousaf, Muhammad N; Ali, Ather; Mehal, Wajahat Z

2018-01-01

Leukocyte activation (LA) testing identifies food items that induce a patient specific cellular response in the immune system, and has recently been shown in a randomized double blinded prospective study to reduce symptoms in patients with irritable bowel syndrome (IBS). We hypothesized that test reactivity to particular food items, and the systemic immune response initiated by these food items, is due to the release of cellular DNA from blood immune cells. We tested this by quantifying total DNA concentration in the cellular supernatant of immune cells exposed to positive and negative foods from 20 healthy volunteers. To establish if the DNA release by positive samples is a specific phenomenon, we quantified myeloperoxidase (MPO) in cellular supernatants. We further assessed if a particular immune cell population (neutrophils, eosinophils, and basophils) was activated by the positive food items by flow cytometry analysis. To identify the signaling pathways that are required for DNA release we tested if specific inhibitors of key signaling pathways could block DNA release. Foods with a positive LA test result gave a higher supernatant DNA content when compared to foods with a negative result. This was specific as MPO levels were not increased by foods with a positive LA test. Protein kinase C (PKC) inhibitors resulted in inhibition of positive food stimulated DNA release. Positive foods resulted in CD63 levels greater than negative foods in eosinophils in 76.5% of tests. LA test identifies food items that result in release of DNA and activation of peripheral blood innate immune cells in a PKC dependent manner, suggesting that this LA test identifies food items that result in release of inflammatory markers and activation of innate immune cells. This may be the basis for the improvement in symptoms in IBS patients who followed an LA test guided diet.

Patient-specific hip prostheses designed by surgeons

Directory of Open Access Journals (Sweden)

Coigny Florian

2016-09-01

Full Text Available Patient-specific bone and joint replacement implants lead to better functional and aesthetic results than conventional methods [1], [2], [3]. But extracting 3D shape information from CT Data and designing individual implants is demanding and requires multiple surgeon-to-engineer interactions. For manufacturing purposes, Additive Manufacturing offers various advantages, especially for low volume manufacturing parts, such as patient specific implants. To ease these new approaches and to avoid surgeon-to-engineer interactions a new design software approach is needed which offers highly automated and user friendly planning steps.

Contingency learning is not affected by conflict experience: Evidence from a task conflict-free, item-specific Stroop paradigm.

Science.gov (United States)

Levin, Yulia; Tzelgov, Joseph

2016-02-01

A contingency learning account of the item-specific proportion congruent effect has been described as an associative stimulus-response learning process that has nothing to do with controlling the Stroop conflict. As supportive evidence, contingency learning has been demonstrated with response conflict-free stimuli, such as neutral words. However, what gives rise to response conflict and to Stroop interference in general is task conflict. The present study investigated whether task conflict can constitute a trigger or, alternatively, a booster to the contingency learning process. This was done by employing a "task conflict-free" condition (i.e., geometric shapes) and comparing it with a "task conflict" condition (i.e., neutral words). The results showed a significant contingency learning effect in both conditions, refuting the possibility that contingency learning is triggered by the presence of a task conflict. Contingency learning was also not enhanced by the task conflict experience, indicating its complete insensitivity to Stroop conflict(s). Thus, the results showed no evidence that performance optimization as a result of contingency learning is greater under conflict, implying that contingency learning is not recruited to assist the control system to overcome conflict. Copyright © 2015 Elsevier B.V. All rights reserved.

The Scientific Context of Product Portfolio Management at Manufacturing Firms

Directory of Open Access Journals (Sweden)

Alvaro Luiz Neuenfeldt Júnior

2014-12-01

Full Text Available Correct product portfolio management is one of the feasible ways of ensuring competitive sustainability before continued market evolution whereby decisions to maintain or exclude an item from the sales offering drives consequences that impact both internal and external contexts. In alignment with this standpoint, the purpose of this study is to identify and pinpoint the conceptual framework on product portfolio management, particularly in as much as existing applications centred on manufacturing sector firms is concerned, so as to allow for the envisioning of possible opportunities of fostering future investigations on the subject matter. To this effect, theoretical-conceptual research was conducted, starting with the primary definition of how this field of study is explored right through to the bibliometric review of existing publications. The end result was the identification a gap in research that focuses on portfolio management at manufacturing companies, particularly in Brazil where only two studies centred on this theme were found, although the country hosts more than 30 types of organizations of this kind.

Semiconductor Manufacturing equipment introduction

International Nuclear Information System (INIS)

Im, Jong Sun

2001-02-01

This book deals with semiconductor manufacturing equipment. It is comprised of nine chapters, which are manufacturing process of semiconductor device, history of semiconductor manufacturing equipment, kinds and role of semiconductor manufacturing equipment, construction and method of semiconductor manufacturing equipment, introduction of various semiconductor manufacturing equipment, spots of semiconductor manufacturing, technical elements of semiconductor manufacturing equipment, road map of technology of semiconductor manufacturing equipment and semiconductor manufacturing equipment in the 21st century.

Item Analysis in Introductory Economics Testing.

Science.gov (United States)

Tinari, Frank D.

1979-01-01

Computerized analysis of multiple choice test items is explained. Examples of item analysis applications in the introductory economics course are discussed with respect to three objectives: to evaluate learning; to improve test items; and to help improve classroom instruction. Problems, costs and benefits of the procedures are identified. (JMD)

A review of the effects on IRT item parameter estimates with a focus on misbehaving common items in test equating

Directory of Open Access Journals (Sweden)

Michalis P Michaelides

2010-10-01

Full Text Available Many studies have investigated the topic of change or drift in item parameter estimates in the context of Item Response Theory. Content effects, such as instructional variation and curricular emphasis, as well as context effects, such as the wording, position, or exposure of an item have been found to impact item parameter estimates. The issue becomes more critical when items with estimates exhibiting differential behavior across test administrations are used as common for deriving equating transformations. This paper reviews the types of effects on IRT item parameter estimates and focuses on the impact of misbehaving or aberrant common items on equating transformations. Implications relating to test validity and the judgmental nature of the decision to keep or discard aberrant common items are discussed, with recommendations for future research into more informed and formal ways of dealing with misbehaving common items.

A Review of the Effects on IRT Item Parameter Estimates with a Focus on Misbehaving Common Items in Test Equating.

Science.gov (United States)

Michaelides, Michalis P

2010-01-01

Many studies have investigated the topic of change or drift in item parameter estimates in the context of item response theory (IRT). Content effects, such as instructional variation and curricular emphasis, as well as context effects, such as the wording, position, or exposure of an item have been found to impact item parameter estimates. The issue becomes more critical when items with estimates exhibiting differential behavior across test administrations are used as common for deriving equating transformations. This paper reviews the types of effects on IRT item parameter estimates and focuses on the impact of misbehaving or aberrant common items on equating transformations. Implications relating to test validity and the judgmental nature of the decision to keep or discard aberrant common items are discussed, with recommendations for future research into more informed and formal ways of dealing with misbehaving common items.

Criteria Considered in Selecting Feed Items for Americium-241 Oxide Production Operations

Energy Technology Data Exchange (ETDEWEB)

Schulte, Louis D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-01-30

The analysis in this document serves the purpose of defining a number of attributes in selection of feed items to be utilized in recovery/recycle of Pu and also production operations of ²⁴¹AmO₂ material intended to meet specification requirements. This document was written in response to a specific request on the part of the 2014 annual program review which took place over the dates of October 28-29, 2014. A number of feed attributes are noted including: (1) Non-interference with existing Pu recovery operations; (2) Content of sufficient ²⁴¹Am to allow process efficiency in recovery operations; (3) Absence of indications that ²⁴³Am might be mixed in with the Pu/²⁴¹Am material; (4) Absence of indications that Cm might be mixed in with the Pu/²⁴¹Am material; (5) Absence of indications of other chemical elements that would present difficulty in chemical separation from ²⁴¹Am; (6) Feed material not expected to present difficulty in dissolution; (7) Dose issues; (8) Process efficiency; (9) Size; (10) Hazard associated with items and package configuration in the vault; (11) Within existing NEPA documentation. The analysis in this document provides a baseline of attributes considered for feed materials, but does not presume to replace the need for technical expertise and judgment on the part of individuals responsible for selecting the material feed to be processed. This document is not comprehensive as regards all attributes that could prove to be important. The value of placing a formal QA hold point on accepting feed items versus more informal management of feed items is discussed in the summation of this analysis. The existing planned QA hold points on ²⁴¹AmO₂ products produced and packaged may be adequate as the entire project is based on QA of the product rather than QA of the process. The probability of introduction of items that would inherently cause the²⁴¹

Diverse task scheduling for individualized requirements in cloud manufacturing

Science.gov (United States)

Zhou, Longfei; Zhang, Lin; Zhao, Chun; Laili, Yuanjun; Xu, Lida

2018-03-01

Cloud manufacturing (CMfg) has emerged as a new manufacturing paradigm that provides ubiquitous, on-demand manufacturing services to customers through network and CMfg platforms. In CMfg system, task scheduling as an important means of finding suitable services for specific manufacturing tasks plays a key role in enhancing the system performance. Customers' requirements in CMfg are highly individualized, which leads to diverse manufacturing tasks in terms of execution flows and users' preferences. We focus on diverse manufacturing tasks and aim to address their scheduling issue in CMfg. First of all, a mathematical model of task scheduling is built based on analysis of the scheduling process in CMfg. To solve this scheduling problem, we propose a scheduling method aiming for diverse tasks, which enables each service demander to obtain desired manufacturing services. The candidate service sets are generated according to subtask directed graphs. An improved genetic algorithm is applied to searching for optimal task scheduling solutions. The effectiveness of the scheduling method proposed is verified by a case study with individualized customers' requirements. The results indicate that the proposed task scheduling method is able to achieve better performance than some usual algorithms such as simulated annealing and pattern search.

A Comparison of the 27-Item and 12-Item Intolerance of Uncertainty Scales

Science.gov (United States)

Khawaja, Nigar G.; Yu, Lai Ngo Heidi

2010-01-01

The 27-item Intolerance of Uncertainty Scale (IUS) has become one of the most frequently used measures of Intolerance of Uncertainty. More recently, an abridged, 12-item version of the IUS has been developed. The current research used clinical (n = 50) and non-clinical (n = 56) samples to examine and compare the psychometric properties of both…

Can items used in 4-year-old well-child visits predict children's health and school outcomes?

Science.gov (United States)

Smithers, Lisa G; Chittleborough, Catherine R; Stocks, Nigel; Sawyer, Michael G; Lynch, John W

2014-08-01

To examine whether items comprising a preschool well-child check for use by family doctors in Australia with 4-5-year old children predicts health and academic outcomes at 6-7 years. The well-child check includes mandatory (anthropometry, eye/vision, ear/hearing, dental, toileting, allergy problems) and non-mandatory (processed food consumption, low physical activity, motor, behaviour/mood problems) items. The predictive validity of mandatory and non-mandatory items measured at 4-5 years was examined using data from the Longitudinal Study of Australian Children. Outcomes at 6-7 years included overweight/obesity, asthma, health care/medication needs, general health, mental health problems, quality of life, teacher-reported mathematics and literacy ability (n = 2,280-2,787). Weight or height >90th centile at 4-5 years predicted overweight/obesity at 6-7 years with 60% sensitivity, 79% specificity and 40% positive predictive value (PPV). Mood/behaviour problems at 4-5 predicted mental health problems at 6-7 years with 86% sensitivity, 40% specificity and 8% PPV. Non-mandatory items improved the discrimination between children with and without mental health problems at 6-7 years (area under the receiver operating characteristic curve 0.75 compared with 0.69 for mandatory items only), but was weak for most outcomes. Items used in a well-child health check were moderate predictors of overweight/obesity and mental health problems at 6-7 years, but poor predictors of other health and academic outcomes.

More is not Always Better: The Relation between Item Response and Item Response Time in Raven’s Matrices

Directory of Open Access Journals (Sweden)

Frank Goldhammer

2015-03-01

Full Text Available The role of response time in completing an item can have very different interpretations. Responding more slowly could be positively related to success as the item is answered more carefully. However, the association may be negative if working faster indicates higher ability. The objective of this study was to clarify the validity of each assumption for reasoning items considering the mode of processing. A total of 230 persons completed a computerized version of Raven’s Advanced Progressive Matrices test. Results revealed that response time overall had a negative effect. However, this effect was moderated by items and persons. For easy items and able persons the effect was strongly negative, for difficult items and less able persons it was less negative or even positive. The number of rules involved in a matrix problem proved to explain item difficulty significantly. Most importantly, a positive interaction effect between the number of rules and item response time indicated that the response time effect became less negative with an increasing number of rules. Moreover, exploratory analyses suggested that the error type influenced the response time effect.

Using genetic algorithm to determine the optimal order quantities for multi-item multi-period under warehouse capacity constraints in kitchenware manufacturing

Science.gov (United States)

Saraswati, D.; Sari, D. K.; Johan, V.

2017-11-01

The study was conducted on a manufacturer that produced various kinds of kitchenware with kitchen sink as the main product. There were four types of steel sheets selected as the raw materials of the kitchen sink. The problem was the manufacturer wanted to determine how much steel sheets to order from a single supplier to meet the production requirements in a way to minimize the total inventory cost. In this case, the economic order quantity (EOQ) model was developed using all-unit discount as the price of steel sheets and the warehouse capacity was limited. Genetic algorithm (GA) was used to find the minimum of the total inventory cost as a sum of purchasing cost, ordering cost, holding cost and penalty cost.

Identifying Sources of Scientific Knowledge: classifying non-source items in the WoS

Energy Technology Data Exchange (ETDEWEB)

Calero-Medina, C.M.

2016-07-01

The sources of scientific knowledge can be tracked using the references in scientific publications. For instance, the publications from the scientific journals covered by the Web of Science database (WoS) contain references to publications for which an indexed source record exist in the WoS (source items) or to references for which an indexed source record does not exist in the WoS (non-source items). The classification of the non-source items is the main objective of the work in progress presented here. Some other scholars have classified and identified non-source items with different purposes (e.g. Butler & Visser (2006); Liseé, Larivière & Archambault (2008); Nerderhof, van Leeuwen & van Raan (2010); Hicks & Wang (2013); Boyack & Klavans (2014)). But these studies are focused in specific source types, fields or set of papers. The work presented here is much broader in terms of the number of publications, source types and fields. (Author)

Refreshing memory traces: thinking of an item improves retrieval from visual working memory.

Science.gov (United States)

Souza, Alessandra S; Rerko, Laura; Oberauer, Klaus

2015-03-01

This article provides evidence that refreshing, a hypothetical attention-based process operating in working memory (WM), improves the accessibility of visual representations for recall. "Thinking of", one of several concurrently active representations, is assumed to refresh its trace in WM, protecting the representation from being forgotten. The link between refreshing and WM performance, however, has only been tenuously supported by empirical evidence. Here, we controlled which and how often individual items were refreshed in a color reconstruction task by presenting cues prompting participants to think of specific WM items during the retention interval. We show that the frequency with which an item is refreshed improves recall of this item from visual WM. Our study establishes a role of refreshing in recall from visual WM and provides a new method for studying the impact of refreshing on the amount of information we can keep accessible for ongoing cognition. © 2014 New York Academy of Sciences.

Preferred Reporting Items for a Systematic Review and Meta-analysis of Diagnostic Test Accuracy Studies: The PRISMA-DTA Statement.

Science.gov (United States)

McInnes, Matthew D F; Moher, David; Thombs, Brett D; McGrath, Trevor A; Bossuyt, Patrick M; Clifford, Tammy; Cohen, Jérémie F; Deeks, Jonathan J; Gatsonis, Constantine; Hooft, Lotty; Hunt, Harriet A; Hyde, Christopher J; Korevaar, Daniël A; Leeflang, Mariska M G; Macaskill, Petra; Reitsma, Johannes B; Rodin, Rachel; Rutjes, Anne W S; Salameh, Jean-Paul; Stevens, Adrienne; Takwoingi, Yemisi; Tonelli, Marcello; Weeks, Laura; Whiting, Penny; Willis, Brian H

2018-01-23

Systematic reviews of diagnostic test accuracy synthesize data from primary diagnostic studies that have evaluated the accuracy of 1 or more index tests against a reference standard, provide estimates of test performance, allow comparisons of the accuracy of different tests, and facilitate the identification of sources of variability in test accuracy. To develop the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) diagnostic test accuracy guideline as a stand-alone extension of the PRISMA statement. Modifications to the PRISMA statement reflect the specific requirements for reporting of systematic reviews and meta-analyses of diagnostic test accuracy studies and the abstracts for these reviews. Established standards from the Enhancing the Quality and Transparency of Health Research (EQUATOR) Network were followed for the development of the guideline. The original PRISMA statement was used as a framework on which to modify and add items. A group of 24 multidisciplinary experts used a systematic review of articles on existing reporting guidelines and methods, a 3-round Delphi process, a consensus meeting, pilot testing, and iterative refinement to develop the PRISMA diagnostic test accuracy guideline. The final version of the PRISMA diagnostic test accuracy guideline checklist was approved by the group. The systematic review (produced 64 items) and the Delphi process (provided feedback on 7 proposed items; 1 item was later split into 2 items) identified 71 potentially relevant items for consideration. The Delphi process reduced these to 60 items that were discussed at the consensus meeting. Following the meeting, pilot testing and iterative feedback were used to generate the 27-item PRISMA diagnostic test accuracy checklist. To reflect specific or optimal contemporary systematic review methods for diagnostic test accuracy, 8 of the 27 original PRISMA items were left unchanged, 17 were modified, 2 were added, and 2 were omitted. The 27-item

78 FR 11679 - Notice of Intent To Repatriate a Cultural Item: Binghamton University, State University of New...

Science.gov (United States)

2013-02-19

... with the appropriate Indian tribes, has determined that a cultural item meets the definition of sacred... the definition of sacred object under 25 U.S.C. 3001. This notice is published as part of the National... item described above is a specific ceremonial object needed by traditional Native American religious...

Negative effects of item repetition on source memory.

Science.gov (United States)

Kim, Kyungmi; Yi, Do-Joon; Raye, Carol L; Johnson, Marcia K

2012-08-01

In the present study, we explored how item repetition affects source memory for new item-feature associations (picture-location or picture-color). We presented line drawings varying numbers of times in Phase 1. In Phase 2, each drawing was presented once with a critical new feature. In Phase 3, we tested memory for the new source feature of each item from Phase 2. Experiments 1 and 2 demonstrated and replicated the negative effects of item repetition on incidental source memory. Prior item repetition also had a negative effect on source memory when different source dimensions were used in Phases 1 and 2 (Experiment 3) and when participants were explicitly instructed to learn source information in Phase 2 (Experiments 4 and 5). Importantly, when the order between Phases 1 and 2 was reversed, such that item repetition occurred after the encoding of critical item-source combinations, item repetition no longer affected source memory (Experiment 6). Overall, our findings did not support predictions based on item predifferentiation, within-dimension source interference, or general interference from multiple traces of an item. Rather, the findings were consistent with the idea that prior item repetition reduces attention to subsequent presentations of the item, decreasing the likelihood that critical item-source associations will be encoded.

Advanced Manufacturing Technologies

Science.gov (United States)

Fikes, John

2016-01-01

Advanced Manufacturing Technologies (AMT) is developing and maturing innovative and advanced manufacturing technologies that will enable more capable and lower-cost spacecraft, launch vehicles and infrastructure to enable exploration missions. The technologies will utilize cutting edge materials and emerging capabilities including metallic processes, additive manufacturing, composites, and digital manufacturing. The AMT project supports the National Manufacturing Initiative involving collaboration with other government agencies.

Examination of the PROMIS upper extremity item bank.

Science.gov (United States)

Hung, Man; Voss, Maren W; Bounsanga, Jerry; Crum, Anthony B; Tyser, Andrew R

Clinical measurement. The psychometric properties of the PROMIS v1.2 UE item bank were tested on various samples prior to its release, but have not been fully evaluated among the orthopaedic population. This study assesses the performance of the UE item bank within the UE orthopaedic patient population. The UE item bank was administered to 1197 adult patients presenting to a tertiary orthopaedic clinic specializing in hand and UE conditions and was examined using traditional statistics and Rasch analysis. The UE item bank fits a unidimensional model (outfit MNSQ range from 0.64 to 1.70) and has adequate reliabilities (person = 0.84; item = 0.82) and local independence (item residual correlations range from -0.37 to 0.34). Only one item exhibits gender differential item functioning. Most items target low levels of function. The UE item bank is a useful clinical assessment tool. Additional items covering higher functions are needed to enhance validity. Supplemental testing is recommended for patients at higher levels of function until more high function UE items are developed. 2c. Copyright © 2016 Hanley & Belfus. Published by Elsevier Inc. All rights reserved.

Psychometric Consequences of Subpopulation Item Parameter Drift

Science.gov (United States)

Huggins-Manley, Anne Corinne

2017-01-01

This study defines subpopulation item parameter drift (SIPD) as a change in item parameters over time that is dependent on subpopulations of examinees, and hypothesizes that the presence of SIPD in anchor items is associated with bias and/or lack of invariance in three psychometric outcomes. Results show that SIPD in anchor items is associated…

Status and Recent Progress in Photovoltaic Manufacturing in the USA

Energy Technology Data Exchange (ETDEWEB)

Witt, C.E.

2001-01-12

This paper describes the present status of photovoltaic technology and recent manufacturing progress obtained through the US Department of Energy's Photovoltaic Manufacturing Technology Project (PVMaT). Although barriers to the widespread use of photovoltaics--a clean and renewable energy--continue to exist, many of these barriers are cost-related and can be addressed through further research on existing approaches. Important areas for development are new materials, improved manufacturing processes, more efficient conversion of sunlight to electricity, and ensured long-term reliability. Improvements in these areas can be expected to lead to lowering of system costs and, ultimately, of energy cost. Specific improvements in manufacturing processes by individual PVMaT participants are described.

Utilizing Mass Customization Methods for Modular Manufacturing System Design

DEFF Research Database (Denmark)

Jørgensen, Steffen; Jacobsen, Alexia; Nielsen, Kjeld

2011-01-01

Markets today have become dynamic and demand rapid product changes, product variety, and customized products. In order to operate under and taking advantages of such conditions requires, amongst other aspects, manufacturing processes robust to product changes - a contradiction to traditional...... manufacturing systems developed as dedicated engineer-to-order solutions, tailored to production of a specific product or a limited product assortment. In response, modular manufacturing concepts are evolving, which are aimed at possessing the needed responsiveness and aimed at being the manufacturing paradigm...... of Mass Customization (MC). Research focus has been on the basic principles and enabling technologies, while modular architectures and system design have received less attention. A potential to fill these gaps by applying selected design theories and methods of MC have been seen. Based on a communality...

Location Indices for Ordinal Polytomous Items Based on Item Response Theory. Research Report. ETS RR-15-20

Science.gov (United States)

Ali, Usama S.; Chang, Hua-Hua; Anderson, Carolyn J.

2015-01-01

Polytomous items are typically described by multiple category-related parameters; situations, however, arise in which a single index is needed to describe an item's location along a latent trait continuum. Situations in which a single index would be needed include item selection in computerized adaptive testing or test assembly. Therefore single…

Additive Manufacturing of Wind Turbine Molds

Energy Technology Data Exchange (ETDEWEB)

Post, Brian [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Richardson, Bradley [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Lloyd, Peter [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Love, Lonnie [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Nolet, Stephen [TPI Composites, Scottsdale, AZ (United States); Hannan, James [TPI Composites, Scottsdale, AZ (United States)

2017-07-01

The objective of this project was to explore the utility of Big Area Additive Manufacturing (BAAM) for low cost manufacturing of wind turbine molds. Engineers at Oak Ridge National Laboratory (ORNL) and TPI Composites (TPI) collaborated to design and manufacture a printed mold that can be used for resin infusion of wind turbine components. Specific focus was on required material properties (operating temperatures and pressures, coefficient of thermal expansion (CTE), thermal conductivity), surface finish (accuracy and coatings) and system integration (integrated vacuum ports, and heating element). The project began with a simple proof of principle components, targeting surface coatings and material properties for printing a small section (approximately 4’ x 4’ x 2’) of a mold. Next, the second phase scaled up and integrated with the objective of capturing all of the necessary components (integrated heating to accelerate cure time, and vacuum, sealing) for resin infusion on a mold of significant size (8’ x 20’ x 6’).

Item response theory analysis applied to the Spanish version of the Personal Outcomes Scale.

Science.gov (United States)

Guàrdia-Olmos, J; Carbó-Carreté, M; Peró-Cebollero, M; Giné, C

2017-11-01

The study of measurements of quality of life (QoL) is one of the great challenges of modern psychology and psychometric approaches. This issue has greater importance when examining QoL in populations that were historically treated on the basis of their deficiency, and recently, the focus has shifted to what each person values and desires in their life, as in cases of people with intellectual disability (ID). Many studies of QoL scales applied in this area have attempted to improve the validity and reliability of their components by incorporating various sources of information to achieve consistency in the data obtained. The adaptation of the Personal Outcomes Scale (POS) in Spanish has shown excellent psychometric attributes, and its administration has three sources of information: self-assessment, practitioner and family. The study of possible congruence or incongruence of observed distributions of each item between sources is therefore essential to ensure a correct interpretation of the measure. The aim of this paper was to analyse the observed distribution of items and dimensions from the three Spanish POS information sources cited earlier, using the item response theory. We studied a sample of 529 people with ID and their respective practitioners and family member, and in each case, we analysed items and factors using Samejima's model of polytomic ordinal scales. The results indicated an important number of items with differential effects regarding sources, and in some cases, they indicated significant differences in the distribution of items, factors and sources of information. As a result of this analysis, we must affirm that the administration of the POS, considering three sources of information, was adequate overall, but a correct interpretation of the results requires that it obtain much more information to consider, as well as some specific items in specific dimensions. The overall ratings, if these comments are considered, could result in bias. © 2017

Manufacture of clinical-grade CD19-specific T cells stably expressing chimeric antigen receptor using Sleeping Beauty system and artificial antigen presenting cells.

Directory of Open Access Journals (Sweden)

Harjeet Singh

Full Text Available Adoptive transfer of T cells expressing a CD19-specific chimeric antigen receptor (CAR is being evaluated in multiple clinical trials. Our current approach to adoptive immunotherapy is based on a second generation CAR (designated CD19RCD28 that signals through a CD28 and CD3-ζ endodomain. T cells are electroporated with DNA plasmids from the Sleeping Beauty (SB transposon/transposase system to express this CAR. Stable integrants of genetically modified T cells can then be retrieved when co-cultured with designer artificial antigen presenting cells (aAPC in the presence of interleukin (IL-2 and 21. Here, we reveal how the platform technologies of SB-mediated transposition and CAR-dependent propagation on aAPC were adapted for human application. Indeed, we have initiated clinical trials in patients with high-risk B-lineage malignancies undergoing autologous and allogeneic hematopoietic stem-cell transplantation (HSCT. We describe the process to manufacture clinical grade CD19-specific T cells derived from healthy donors. Three validation runs were completed in compliance with current good manufacturing practice for Phase I/II trials demonstrating that by 28 days of co-culture on γ-irradiated aAPC ∼10(10 T cells were produced of which >95% expressed CAR. These genetically modified and propagated T cells met all quality control testing and release criteria in support of infusion.

TIIREC: A Tensor Approach for Tag-Driven Item Recommendation with Sparse User Generated Content

KAUST Repository

Yu, Lu

2017-05-17

In recent years, tagging system has become a building block o summarize the content of items for further functions like retrieval or personalized recommendation in various web applications. One nontrivial requirement is to precisely deliver a list of suitable items when users interact with the systems via inputing a specific tag (i.e. a query term). Different from traditional recommender systems, we need deal with a collaborative retrieval (CR) problem, where both characteristics of retrieval and recommendation should be considered to model a ternary relationship involved with query× user× item. Recently, several works are proposed to study CR task from users’ perspective. However, they miss a significant challenge raising from the sparse content of items. In this work, we argue that items will suffer from the sparsity problem more severely than users, since items are usually observed with fewer features to support a feature-based or content-based algorithm. To tackle this problem, we aim to sufficiently explore the sophisticated relationship of each query× user× item triple from items’ perspective. By integrating item-based collaborative information for this joint task, we present an alternative factorized model that could better evaluate the ranks of those items with sparse information for the given query-user pair. In addition, we suggest to employ a recently proposed bayesian personalized ranking (BPR) algorithm to optimize latent collaborative retrieval problem from pairwise learning perspective. The experimental results on two real-world datasets, (i.e. Last.fm, Yelp), verified the efficiency and effectiveness of our proposed approach at top-k ranking metric.

Development and validation of an item response theory-based Social Responsiveness Scale short form.

Science.gov (United States)

Sturm, Alexandra; Kuhfeld, Megan; Kasari, Connie; McCracken, James T

2017-09-01

Research and practice in autism spectrum disorder (ASD) rely on quantitative measures, such as the Social Responsiveness Scale (SRS), for characterization and diagnosis. Like many ASD diagnostic measures, SRS scores are influenced by factors unrelated to ASD core features. This study further interrogates the psychometric properties of the SRS using item response theory (IRT), and demonstrates a strategy to create a psychometrically sound short form by applying IRT results. Social Responsiveness Scale analyses were conducted on a large sample (N = 21,426) of youth from four ASD databases. Items were subjected to item factor analyses and evaluation of item bias by gender, age, expressive language level, behavior problems, and nonverbal IQ. Item selection based on item psychometric properties, DIF analyses, and substantive validity produced a reduced item SRS short form that was unidimensional in structure, highly reliable (α = .96), and free of gender, age, expressive language, behavior problems, and nonverbal IQ influence. The short form also showed strong relationships with established measures of autism symptom severity (ADOS, ADI-R, Vineland). Degree of association between all measures varied as a function of expressive language. Results identified specific SRS items that are more vulnerable to non-ASD-related traits. The resultant 16-item SRS short form may possess superior psychometric properties compared to the original scale and emerge as a more precise measure of ASD core symptom severity, facilitating research and practice. Future research using IRT is needed to further refine existing measures of autism symptomatology. © 2017 Association for Child and Adolescent Mental Health.

TIIREC: A Tensor Approach for Tag-Driven Item Recommendation with Sparse User Generated Content

KAUST Repository

Yu, Lu; Huang, Junming; Zhou, Ge; Liu, Chuang; Zhang, Zi-Ke

2017-01-01

In recent years, tagging system has become a building block o summarize the content of items for further functions like retrieval or personalized recommendation in various web applications. One nontrivial requirement is to precisely deliver a list of suitable items when users interact with the systems via inputing a specific tag (i.e. a query term). Different from traditional recommender systems, we need deal with a collaborative retrieval (CR) problem, where both characteristics of retrieval and recommendation should be considered to model a ternary relationship involved with query× user× item. Recently, several works are proposed to study CR task from users’ perspective. However, they miss a significant challenge raising from the sparse content of items. In this work, we argue that items will suffer from the sparsity problem more severely than users, since items are usually observed with fewer features to support a feature-based or content-based algorithm. To tackle this problem, we aim to sufficiently explore the sophisticated relationship of each query× user× item triple from items’ perspective. By integrating item-based collaborative information for this joint task, we present an alternative factorized model that could better evaluate the ranks of those items with sparse information for the given query-user pair. In addition, we suggest to employ a recently proposed bayesian personalized ranking (BPR) algorithm to optimize latent collaborative retrieval problem from pairwise learning perspective. The experimental results on two real-world datasets, (i.e. Last.fm, Yelp), verified the efficiency and effectiveness of our proposed approach at top-k ranking metric.

Experiences of using the GMP audit preparation tool in pharmaceutical contract manufacturer audits.

Science.gov (United States)

Linna, Anu; Korhonen, Mirka; Airaksinen, Marja; Juppo, Anne Mari

2010-06-01

Use of external contractors is nowadays inevitable in the pharmaceutical industry. Therefore the amount of current good manufacturing practice audits has been increasing. During the audit, a large amount of items should be covered in a limited amount of time. Consequently, pharmaceutical companies should have systematic and effective ways to manage and prepare for the audits. This study is a continuation to the earlier study, where a tool for the preparation of cGMP audit was developed and its content was validated. The objective of this study was to evaluate the usefulness of the developed tool in audit preparation and during the actual cGMP audit. Three qualitative research methods were used in this study (observation, interviews, and opinion survey). First, the validity of the information given through the tool was examined by comparing the responses to the actual conditions observed during the contract manufacturer audits (n = 15). Additionally the opinions of the contract manufacturers of the tool were gathered (n = 10) and the auditors were interviewed (n = 2). The developed tool was proven to be useful in audit preparation phase from both the auditor's and the contract manufacturers' point of view. Furthermore, using the tool can also save some time when performing the audit. The results show that using the tool can give significant support in audit preparation phase and also during the actual audit.

Construct validity of the items on the Stroke Specific Quality of Life (SS-QOL) questionnaire that evaluate the participation component of the International Classification of Functioning, Disability and Health.

Science.gov (United States)

Silva, Soraia Micaela; Corrêa, Fernanda Ishida; Pereira, Gabriela Santos; Faria, Christina Danielli Coelho de Morais; Corrêa, João Carlos Ferrari

2018-01-01

Analyze the construct validity and internal consistency of the Stroke Specific Quality of Life (SS-QOL) items that address the participation component of the ICF as well as analyze the ceiling and floor effects. One hundred subjects were analyzed: 85 community-dwelling and 15 institutionalized individuals. The analysis of construct validity was performed using classic psychometrics: (1) the comparison of known groups (individuals without restriction to participation vs. those with restriction to participation) using the Mann-Whitney test and (2) convergent validity - correlation between the scores on the SS-QOL items that address participation and the subscale scores of measures used to evaluate the similar constructs and concepts [the Short-Form Health Survey (SF-36), Functional Independence Measure (FIM) and grip strength test]. Spearman's correlation coefficients were calculated for this analysis. Cronbach's α was used for the analysis of internal consistency and both the ceiling and floor effects were analyzed. The level of significance for all analyses was α = 0.05. The a priori hypotheses regarding construct validity were partially demonstrated, as only five of the eight domains exhibited positive moderate to strong correlations (r > 0.40) with measures that address constructs similar to those addressed on the SS-QOL questionnaire. The items demonstrated adequate internal consistency and are capable of differentiating individuals with and without restriction to participation. The ceiling and floor effects were considered adequate for the total SS-QOL score, but beyond acceptable standards for some domains. The 26 items of the SS-QOL questionnaire measure a multidimensional construct and therefore do not only address participation. However, the items demonstrated adequate internal consistency and are capable of differentiating individuals with and without restriction to participation. Implications for rehabilitation The 26 items of the SS

Additive manufacturing of metals

International Nuclear Information System (INIS)

Herzog, Dirk; Seyda, Vanessa; Wycisk, Eric; Emmelmann, Claus

2016-01-01

Additive Manufacturing (AM), the layer-by layer build-up of parts, has lately become an option for serial production. Today, several metallic materials including the important engineering materials steel, aluminium and titanium may be processed to full dense parts with outstanding properties. In this context, the present overview article describes the complex relationship between AM processes, microstructure and resulting properties for metals. It explains the fundamentals of Laser Beam Melting, Electron Beam Melting and Laser Metal Deposition, and introduces the commercially available materials for the different processes. Thereafter, typical microstructures for additively manufactured steel, aluminium and titanium are presented. Special attention is paid to AM specific grain structures, resulting from the complex thermal cycle and high cooling rates. The properties evolving as a consequence of the microstructure are elaborated under static and dynamic loading. According to these properties, typical applications are presented for the materials and methods for conclusion.

Loglinear multidimensional IRT models for polytomously scired Items

NARCIS (Netherlands)

Kelderman, Henk

1988-01-01

A loglinear item response theory (IRT) model is proposed that relates polytomously scored item responses to a multidimensional latent space. Each item may have a different response function where each item response may be explained by one or more latent traits. Item response functions may follow a

48 CFR 852.214-72 - Alternate item(s).

Science.gov (United States)

2010-10-01

... AND FORMS SOLICITATION PROVISIONS AND CONTRACT CLAUSES Texts of Provisions and Clauses 852.214-72... 2008) Bids on []* will be given equal consideration along with bids on []** and any such bids received... [].** * Contracting officer will insert an alternate item that is considered acceptable. ** Contracting officer will...

Decade of PV Industry R and D Advances in Silicon Module Manufacturing

Energy Technology Data Exchange (ETDEWEB)

Symko-Davis, M.; Mitchell, R.L.; Witt, C.E.; Thomas, H.P. [National Renewable Energy Laboratory; King, R.[U.S. Department of Energy; Ruby, D.S. [Sandia National Laboratories

2001-01-18

The US Photovoltaic (PV) industry has made significant technical advances in crystalline silicon (Si) module manufacturing through the PV Manufacturing R and D Project during the past decade. Funded Si technologies in this project have been Czochralski, cast polycrystalline, edge-defined film-fed growth (EFG) ribbon, string ribbon, and Si-film. Specific R and D Si module-manufacturing categories that have shown technical growth and will be discussed are in crystal growth and processing, wafering, cell fabrication, and module manufacturing. These R and D advancements since 1992 have contributed to a 30% decrease in PV manufacturing costs and stimulated a sevenfold increase in PV production capacity.

Shaping Collaboration 2006: action items for the LHC

Energy Technology Data Exchange (ETDEWEB)

Goldfarb, S [CERN-PH, 1211 Geneva 23 (Switzerland); Herr, J; Neal, H A [Assistant Research Scientist, University of Michigan (United States); Research Process Manager, University of Michigan (United States); Professor of Physics, University of Michigan (United States)], E-mail: steven.goldfarb@cern.ch

2008-07-15

Shaping Collaboration 2006 [1] was a workshop held in Geneva, on December 11-13, 2006, to examine the status and future of collaborative tool technology and its usage for large global scientific collaborations, such as those of the CERN LHC [2]. The workshop brought together some of the leading experts in the field of collaborative tools (WACE 2006) [3] with physicists and developers of the LHC collaborations and HENP (High-Energy and Nuclear Physics). We highlight important presentations and key discussions held during the workshop, then focus on a large and aggressive set of goals and specific action items targeted at institutes from all levels of the LHC organization. This list of action items, assembled during a panel discussion at the close of the LHC sessions, includes recommendations for the LHC Users, their Universities, Project Managers, Spokespersons, National Funding Agencies and Host Laboratories. We present this list, along with suggestions for priorities in addressing the immediate and long-term needs of HENP.

Shaping Collaboration 2006: action items for the LHC

International Nuclear Information System (INIS)

Goldfarb, S; Herr, J; Neal, H A

2008-01-01

Shaping Collaboration 2006 [1] was a workshop held in Geneva, on December 11-13, 2006, to examine the status and future of collaborative tool technology and its usage for large global scientific collaborations, such as those of the CERN LHC [2]. The workshop brought together some of the leading experts in the field of collaborative tools (WACE 2006) [3] with physicists and developers of the LHC collaborations and HENP (High-Energy and Nuclear Physics). We highlight important presentations and key discussions held during the workshop, then focus on a large and aggressive set of goals and specific action items targeted at institutes from all levels of the LHC organization. This list of action items, assembled during a panel discussion at the close of the LHC sessions, includes recommendations for the LHC Users, their Universities, Project Managers, Spokespersons, National Funding Agencies and Host Laboratories. We present this list, along with suggestions for priorities in addressing the immediate and long-term needs of HENP

Ubiquitous Robotic Technology for Smart Manufacturing System.

Science.gov (United States)

Wang, Wenshan; Zhu, Xiaoxiao; Wang, Liyu; Qiu, Qiang; Cao, Qixin

2016-01-01

As the manufacturing tasks become more individualized and more flexible, the machines in smart factory are required to do variable tasks collaboratively without reprogramming. This paper for the first time discusses the similarity between smart manufacturing systems and the ubiquitous robotic systems and makes an effort on deploying ubiquitous robotic technology to the smart factory. Specifically, a component based framework is proposed in order to enable the communication and cooperation of the heterogeneous robotic devices. Further, compared to the service robotic domain, the smart manufacturing systems are often in larger size. So a hierarchical planning method was implemented to improve the planning efficiency. A test bed of smart factory is developed. It demonstrates that the proposed framework is suitable for industrial domain, and the hierarchical planning method is able to solve large problems intractable with flat methods.

Losing Items in the Psychogeriatric Nursing Home

Directory of Open Access Journals (Sweden)

J. van Hoof PhD

2016-09-01

Full Text Available Introduction: Losing items is a time-consuming occurrence in nursing homes that is ill described. An explorative study was conducted to investigate which items got lost by nursing home residents, and how this affects the residents and family caregivers. Method: Semi-structured interviews and card sorting tasks were conducted with 12 residents with early-stage dementia and 12 family caregivers. Thematic analysis was applied to the outcomes of the sessions. Results: The participants stated that numerous personal items and assistive devices get lost in the nursing home environment, which had various emotional, practical, and financial implications. Significant amounts of time are spent on trying to find items, varying from 1 hr up to a couple of weeks. Numerous potential solutions were identified by the interviewees. Discussion: Losing items often goes together with limitations to the participation of residents. Many family caregivers are reluctant to replace lost items, as these items may get lost again.

Development of novel IVD assays: a manufacturer's perspective.

Science.gov (United States)

Metcalfe, Thomas A

2010-01-01

IVD manufacturers are heavily reliant on novel IVD assays to fuel their growth and drive innovation within the industry. They represent a key part of the IVD industry's value proposition to customers and the healthcare industry in general, driving product differentiation, helping to create demand for new systems and generating incremental revenue. However, the discovery of novel biomarkers and their qualification for a specific clinical purpose is a high risk undertaking and the large, risky investments associated with doing this on a large scale are incompatible with IVD manufacturer's business models. This article describes the sources of novel IVD assays, the processes for discovering and qualifying novel assays and the reliance of IVD manufacturers on collaborations and in-licensing to source new IVD assays for their platforms.

Manufactured Home Energy Audit (MHEA)Users Manual (Version 7)

Energy Technology Data Exchange (ETDEWEB)

Gettings, M.B.

2003-01-27

The Manufactured Home Energy Audit (MHEA) is a software tool that predicts manufactured home energy consumption and recommends weatherization retrofit measures. It was developed to assist local weatherization agencies working with the U.S. Department of Energy (DOE) Weatherization Assistance Program. Whether new or experienced, employed within or outside the Weatherization Assistance Program, all users can benefit from incorporating MHEA into their manufactured home weatherization programs. DOE anticipates that the state weatherization assistance programs that incorporate MHEA into their programs will find significant growth in the energy and cost savings achieved from manufactured home weatherization. The easy-to-use MHEA uses a relatively standard Windows graphical interface for entering simple inputs and provides understandable, usable results. The user enters information about the manufactured home construction, heating equipment, cooling equipment appliances, and weather site. MHEA then calculates annual energy consumption using a simplified building energy analysis technique. Weatherization retrofit measures are evaluated based on the predicted energy savings after installation of the measure, the measure cost, and the measure life. Finally, MHEA recommends retrofit measures that are energy and cost effective for the particular home being evaluated. MHEA evaluates each manufactured home individually and takes into account local weather conditions, retrofit measure costs, and fuel costs. The recommended package of weatherization retrofit measures is tailored to the home being evaluated. More traditional techniques apply the same package of retrofit measures to all manufactured homes, often the same set of measures that are installed into site-built homes. Effective manufactured home weatherization can be achieved only by installing measures developed specifically for manufactured homes. The unique manufactured home construction characteristics require that

Design and application of reconfigurable manufacturing systems in agile mass customization manufacturing environment.

CSIR Research Space (South Africa)

Xing, B

2007-05-01

Full Text Available processes. Many manufacturing techniques are based on the principles of Flexible Manufacturing and Dedicated Manufacturing for mass production. Reconfigurable Manufacturing System, (RMS), is a manufacturing system that can provide for Agile Manufacturing...

‘Forget me (not?’ – Remembering forget-items versus un-cued items in directed forgetting

Directory of Open Access Journals (Sweden)

Bastian eZwissler

2015-11-01

Full Text Available Humans need to be able to selectively control their memories. Here, we investigate the underlying processes in item-method directed forgetting and compare the classic active memory cues in this paradigm with a passive instruction. Typically, individual items are presented and each is followed by either a forget- or remember-instruction. On a surprise test of all items, memory is then worse for to-be-forgotten items (TBF compared to to-be-remembered items (TBR. This is thought to result from selective rehearsal of TBR, or from active inhibition of TBF, or from both. However, evidence suggests that if a forget instruction initiates active processing, paradoxical effects may also arise. To investigate the underlying mechanisms, four experiments were conducted where un-cued items (UI were introduced and recognition performance was compared between TBR, TBF and UI stimuli. Accuracy was encouraged via a performance-dependent monetary bonus. Across all experiments, including perceptually fully matched variants, memory accuracy for TBF was reduced compared to TBR, but better than for UI. Moreover, participants used a more conservative response criterion when responding to TBF stimuli. Thus, ironically, the F cue results in active processing, but this does not have inhibitory effects that would impair recognition memory beyond a un-cued baseline condition. This casts doubts on inhibitory accounts of item-method directed forgetting and is also difficult to reconcile with pure selective rehearsal of TBR. While the F-cue does induce active processing, this does not result in particularly successful forgetting. The pattern seems most consistent with the notion of ironic processing.

Manufacture of semifinished items of alloys V-4Ti-4Cr and V-10Ti-5Cr for use as a structural material in fusion applications

International Nuclear Information System (INIS)

Potapenko, M.M.; Drobishev, V.A.; Filkin, V.Y.; Gubkin, I.N.; Myasnikov, V.V.; Nikulin, A.D.; Shingarev, E.N.; Vedernikov, G.P.; Votinov, S.N.; Zurabov, V.S.; Zolotarev, A.B.

1996-01-01

Vanadium-titanium-chromium alloys are considered as structural materials with the most appropriate properties for fusion applications. However, the final ratio V-Ti-Cr in an alloy is not yet determined. On the one hand, it is offered to optimize structure on the basis of an alloy V-4Ti-4Cr. On the other hand, it is proposed that the optimum of total Ti and Cr content should be near 15%, and the Ti to Cr ratio should be 2:1. Melting, casting and processing by pressure of ingots of vanadium alloys V-4Ti-4Cr and V-10Ti-5Cr weighing as much as 50 kg are considered in the report. The ingots in diameters up to 130 mm were obtained by melting in vacuum-arc furnaces. Results on chemical uniformity and structure of the ingots are presented. A basic scheme of semifinished items manufacture is submitted. Rod and tube hot extrusion conditions are presented. A new technology for protection of ingot and billet surface from gases during hot processing is used to discard application of protective stainless steel and to lower temperature of processing. Sheet and tube products were made from extruded billets by cold rolling with intermediate heat treatment. The list of obtained products, including sheets 0.5-5 mm thick, rods 10-18 mm in diameter and tubes from 50 mm up to 6.0 mm in diameter is presented. The availability of large-scale ingots processing with weight above 300 kg is discussed. (orig.)

Transcranial direct current stimulation over the parietal cortex alters bias in item and source memory tasks.

Science.gov (United States)

Pergolizzi, Denise; Chua, Elizabeth F

2016-10-01

Neuroimaging data have shown that activity in the lateral posterior parietal cortex (PPC) correlates with item recognition and source recollection, but there is considerable debate about its specific contributions. Performance on both item and source memory tasks were compared between participants who were given bilateral transcranial direct current stimulation (tDCS) over the parietal cortex to those given prefrontal or sham tDCS. The parietal tDCS group, but not the prefrontal group, showed decreased false recognition, and less bias in item and source discrimination tasks compared to sham stimulation. These results are consistent with a causal role of the PPC in item and source memory retrieval, likely based on attentional and decision-making biases. Copyright © 2016 Elsevier Inc. All rights reserved.

Cloud Manufacturing Service Paradigm for Group Manufacturing Companies

Directory of Open Access Journals (Sweden)

Jingtao Zhou

2014-07-01

Full Text Available The continuous refinement of specialization requires that the group manufacturing company must be constantly focused on how to concentrate its core resources in special sphere to form its core competitive advantage. However, the resources in enterprise group are usually distributed in different subsidiary companies, which means they cannot be fully used, constraining the competition and development of the enterprise. Conducted as a response to a need for cloud manufacturing studies, systematic and detailed studies on cloud manufacturing schema for group companies are carried out in this paper. A new hybrid private clouds paradigm is proposed to meet the requirements of aggregation and centralized use of heterogeneous resources and business units distributed in different subsidiary companies. After the introduction of the cloud manufacturing paradigm for enterprise group and its architecture, this paper presents a derivation from the abstraction of paradigm and framework to the application of a practical evaluative working mechanism. In short, the paradigm establishes an effective working mechanism to translate collaborative business process composed by the activities into cloud manufacturing process composed by services so as to create a foundation resulting in mature traditional project monitoring and scheduling technologies being able to be used in cloud manufacturing project management.

International Competition and Small-Firm Exit in US Manufacturing

OpenAIRE

Robert M Feinberg

2013-01-01

This study analyzes both the determinants of small firm exit rates in US manufacturing over the 1989–2004 period, especially the reaction of domestic firms to the nature of foreign competition as measured by industry-specific real exchange rate movements (interacted with import penetration by industry). These international pressures seem to lead to increased rates of smallest-firm exit in manufacturing, though the magnitudes of these effects are smaller than sometimes discussed. However, high...

Layout design optimization of dynamic environment flexible manufacturing systems

Directory of Open Access Journals (Sweden)

Jaber Abu Qudeiri

2015-06-01

Full Text Available The proper positioning of machine tools in flexible manufacturing system is one of the factors that lead to increase in production efficiency. Choosing the optimum position of machine tools curtails the total part handling cost between machine tools within the flexible manufacturing system. In this article, a two-stage approach is presented to investigate the best locations of the machine tools in flexible manufacturing system. The location of each machine tool is selected from the available specific and fixed locations in such a way that it will result in best throughput of the flexible manufacturing system. In the first stage of the two-stage approach, the throughput of randomly selected locations of the machine tool in flexible manufacturing system is computed by proposing a production simulation system. The production simulation system utilizes genetic algorithms to find the locations of the machine tools in flexible manufacturing system that achieve the maximum throughput of the flexible manufacturing system. In the second stage, the generated locations are fed into artificial neural network to find a relation between a machine tool’s location and the throughput that can be used to predict the throughput for any other set of locations. Artificial neural network will result in mitigating the computational time.

A quality risk management model approach for cell therapy manufacturing.

Science.gov (United States)

Lopez, Fabio; Di Bartolo, Chiara; Piazza, Tommaso; Passannanti, Antonino; Gerlach, Jörg C; Gridelli, Bruno; Triolo, Fabio

2010-12-01

International regulatory authorities view risk management as an essential production need for the development of innovative, somatic cell-based therapies in regenerative medicine. The available risk management guidelines, however, provide little guidance on specific risk analysis approaches and procedures applicable in clinical cell therapy manufacturing. This raises a number of problems. Cell manufacturing is a poorly automated process, prone to operator-introduced variations, and affected by heterogeneity of the processed organs/tissues and lot-dependent variability of reagent (e.g., collagenase) efficiency. In this study, the principal challenges faced in a cell-based product manufacturing context (i.e., high dependence on human intervention and absence of reference standards for acceptable risk levels) are identified and addressed, and a risk management model approach applicable to manufacturing of cells for clinical use is described for the first time. The use of the heuristic and pseudo-quantitative failure mode and effect analysis/failure mode and critical effect analysis risk analysis technique associated with direct estimation of severity, occurrence, and detection is, in this specific context, as effective as, but more efficient than, the analytic hierarchy process. Moreover, a severity/occurrence matrix and Pareto analysis can be successfully adopted to identify priority failure modes on which to act to mitigate risks. The application of this approach to clinical cell therapy manufacturing in regenerative medicine is also discussed. © 2010 Society for Risk Analysis.

Innovative High-Performance Deposition Technology for Low-Cost Manufacturing of OLED Lighting

Energy Technology Data Exchange (ETDEWEB)

Scott, David; Hamer, John

2017-06-30

In this project, OLEDWorks developed and demonstrated the innovative high-performance deposition technology required to deliver dramatic reductions in the cost of manufacturing OLED lighting in production equipment. The current high manufacturing cost of OLED lighting is the most urgent barrier to its market acceptance. The new deposition technology delivers solutions to the two largest parts of the manufacturing cost problem – the expense per area of good product for organic materials and for the capital cost and depreciation of the equipment. Organic materials cost is the largest expense item in the bill of materials and is predicted to remain so through 2020. The high-performance deposition technology developed in this project, also known as the next generation source (NGS), increases material usage efficiency from 25% found in current Gen2 deposition technology to 60%. This improvement alone results in a reduction of approximately $25/m2 of good product in organic materials costs, independent of production volumes. Additionally, this innovative deposition technology reduces the total depreciation cost from the estimated value of approximately $780/m2 of good product for state-of-the-art G2 lines (at capacity, 5-year straight line depreciation) to $170/m2 of good product from the OLEDWorks production line.

Reconfigurable Manufacturing Systems as an Application of Mass Customisation

DEFF Research Database (Denmark)

Jørgensen, Steffen; Nielsen, Kjeld; Jørgensen, Kaj Asbjørn

2011-01-01

Manufacturing systems are today developed as engineer to order solutions tailored to producing a specific product or a limited product mix. Such dedicated systems are not consistent with market demands for rapid product changes, product variety, and customisation, which require flexibility...... and responsiveness of manufacturing systems. A Reconfigurable Manufacturing System (RMS) is aimed at possess such flexibility and responsiveness and is said to be the manufacturing paradigm of tomorrow. RMS is, though, not yet fully developed. A similarity between RMS and modular product families, known from Mass...... Customisation (MC), is seen and based on this similarity a potential to maturing RMS further by applying MC methods and techniques is identified. Based on literature surveys this paper analyses this potential by diagnosing gabs for RMS to succeed as a MC product. For each gab MC theory holds related methods...

WHO Working Group on Technical Specifications for Manufacture and Evaluation of Yellow Fever Vaccines, Geneva, Switzerland, 13-14 May 2009.

Science.gov (United States)

Ferguson, Morag; Shin, Jinho; Knezevic, Ivana; Minor, Philip; Barrett, Alan

2010-12-06

In May 2009, WHO convened a meeting of Working Group on Technical Specifications for Manufacturing and Evaluating Yellow Fever (YF) Vaccines, Geneva, Switzerland to initiate revision of the WHO Recommendations (formerly, Requirements) for YF vaccine published in WHO Technical Report Series number 872 (1998). The Working Group, consisting of experts from academia, industry, national regulatory authorities and national control laboratories, reviewed the latest issues of safety, efficacy and quality of YF vaccines and agreed that (i) the revision should focus on live attenuated YF vaccine virus 17D lineage; and that (ii) nonclinical and clinical guidelines for new vaccines prepared from 17D lineage be developed. Copyright © 2010. Published by Elsevier Ltd.. All rights reserved.

Efficacy of Lean Manufacturing to Improve Production Performance

Directory of Open Access Journals (Sweden)

Israel Balogun

2016-12-01

Full Text Available The lean manufacturing system is a technique of manufacturing products in time. The concept of lean manufacturing principles employs simpler ways of communicating required materials as well as manual technique in ensuring the provision of signals for replenishment of materials the production companies require. Performance on the other hand, can be considered the attainment of value effectively and efficiently. Lean manufacturing and performance production goes hand in hand. Through utilizing lean manufacturing method, most companies would be able to tailor their processes in achieving effective performance and meeting unique requests from their consumers. The exploratory observations conducted in the study was purposely for examining the nature of complex interactions involved between major constructs and environmental sustainability at the parent company and the tire part vendors. The method of the research was a qualitative case study. The research data were obtained from with the case company and through structured interviews the case company's consumers. The case-specific tools were first developed in close co-operation with the case company. Future research agenda addresses gaps in the current literature and suggests relevant framework from which to explore this phenomenon.

Production inventory policies for defective items with inspection errors, sales return, imperfect rework process and backorders

Science.gov (United States)

Jaggi, Chandra K.; Khanna, Aditi; Kishore, Aakanksha

2016-03-01

In order to sustain the challenges of maintaining good quality and perfect screening process, rework process becomes a rescue to compensate for the imperfections present in the production system. The proposed model attempts to explore the existing real-life situation with a more practical approach by incorporating the concept of imperfect rework as this occurs as an unavoidable problem to the firm due to irreparable disorders even in the reworked items. Hence, a production inventory model is formulated here to study the combined effect of imperfect quality items, faulty inspection process and imperfect rework process on the optimal production quantity and optimal backorder level. An analytical method is employed to maximize the expected total profit per unit time. Moreover, the results of several previous research articles namely Chiu et al (2006), Chiu et al (2005), Salameh and Hayek (2001), and classical EPQ with shortages are deduced as special cases. To demonstrate the applicability of the model, and to observe the effects of key parameters on the optimal replenishment policy, a numerical example along with a comprehensive sensitivity analysis has been presented. The pertinence of the model can be found in most of the manufacturing industries like textile, electronics, furniture, footwear, plastics etc. A production lot size model has been explored for defectives items with inspection errors and an imperfect rework process.

Manufacturing Renaissance : Return of manufacturing to western countries

OpenAIRE

Kianian, Babak; Larsson, Tobias; Tavassoli, Mohammad

2013-01-01

This chapter argues that the location of manufacturing is gradually shifting to the west again, exemplifying the ‘manufacturing renaissance’. Such a claim is based on the recent observed trend and the discussion is contextualized within the established theory that has been able to explain the location of manufacturing, that is, the product life cycle (PLC) model. Then the chapter identifies and discusses the four main drivers of this new phenomenon: (i) rising wage levels in emerging economie...

Measuring Manufacturing Innovativeness

DEFF Research Database (Denmark)

Blichfeldt, Henrik; Knudsen, Mette Præst

2017-01-01

Globalization and customization increases the pressure on manufacturing companies, and the ability to provide innovativeness is a potential source of competitive advantage. This paper positions the manufacturing entity in the innovation process, and investigates the relation between innovation vers...... technology and organizational concepts. Based on Danish survey data from the European Manufacturing Survey (EMS-2015) this paper finds that there is a relation between innovative companies, and their level of technology and use of organizational concepts. Technology and organizational concepts act...... as manufacturing levers to support the manufacturing and production system to provide innovativeness. The managerial implication lies in building manufacturing capabilities to support the innovative process, by standardization, optimization and creating stability in combination with automation and advanced...

A sharp image or a sharp knife: norms for the modality-exclusivity of 774 concept-property items.

Science.gov (United States)

van Dantzig, Saskia; Cowell, Rosemary A; Zeelenberg, René; Pecher, Diane

2011-03-01

According to recent embodied cognition theories, mental concepts are represented by modality-specific sensory-motor systems. Much of the evidence for modality-specificity in conceptual processing comes from the property-verification task. When applying this and other tasks, it is important to select items based on their modality-exclusivity. We collected modality ratings for a set of 387 properties, each of which was paired with two different concepts, yielding a total of 774 concept-property items. For each item, participants rated the degree to which the property could be experienced through five perceptual modalities (vision, audition, touch, smell, and taste). Based on these ratings, we computed a measure of modality exclusivity, the degree to which a property is perceived exclusively through one sensory modality. In this paper, we briefly sketch the theoretical background of conceptual knowledge, discuss the use of the property-verification task in cognitive research, provide our norms and statistics, and validate the norms in a memory experiment. We conclude that our norms are important for researchers studying modality-specific effects in conceptual processing.

Guidelines for the technical evaluation of replacement items in nuclear power plants (NCIG-11)

International Nuclear Information System (INIS)

Craig, W.E.; Fakhar, A.A.; Shulman, M.N.

1989-12-01

This document presents guidelines and supporting information for the technical evaluation of replacement items in nuclear power plants. These guidelines contain six major sections which provide the practical knowledge and a programmatic approach to determine the technical and quality requirements necessary to generate purchase documents to procure the proper replacement items. The technical evaluation methodology includes the following steps. (1) Identification of the need for a technical evaluation. (2) Component/part functional classification procedures. (3) Performance of a Failure Modes and Effects Analysis. (4) Selection of Critical Characteristics for Design Determination. (5) Performance of a ''Like-For-Like'' or ''Alternate'' item Evaluation. (6) Preparation of the Technical and Quality Requirements Specification. Work on this document was initiated in response to the increased emphasis by the utilities owning nuclear power plants and nuclear industry on procurement of replacement items for use in safety related applications at nuclear power plants. 20 refs., 9 figs., 14 tabs

Incorporating attitudinal parameter in assessing sustainability of Malaysia manufacturing industry

Science.gov (United States)

Lanang, Wan Nurul Syahirah Wan; Turan, Faiz Mohd; Johan, Kartina

2018-04-01

Numerous companies are accepting sustainability as an organizational peremptory. There is, however, little convergence on how organizations become sustainable. The previous study suggests that a paradigm shift is necessary to incorporate more sustainable ways of thinking, while others advocate that sustainability requires only moderate behavioural changes as in attitude. In addition, it is also suggesting that sustainability develops most effectively when a singular view of sustainability is applied throughout the company; others contend that differentiated views of sustainability emerge within the various subcultures of an organization. The aim of this paper is to analyse the aftermath of considering attitudinal parameter into the initial data, portraying the true nature of personality during the survey. The research presented was carried out with employees from various manufacturing companies with different branches of knowledge and attitude. Survey methodology was employed by building a questionnaire combining Likert-type items, Sustainable Development Goals (SDGs), Green Project Management (GPM) P5 Integration and multiple-option items. The results allow identifying the knowledges and attitudes of the employees in Malaysia context, contributing relevant data in regard to future engagement relating to sustainability and attitudinal parameter.

Item selection via Bayesian IRT models.

Science.gov (United States)

Arima, Serena

2015-02-10

With reference to a questionnaire that aimed to assess the quality of life for dysarthric speakers, we investigate the usefulness of a model-based procedure for reducing the number of items. We propose a mixed cumulative logit model, which is known in the psychometrics literature as the graded response model: responses to different items are modelled as a function of individual latent traits and as a function of item characteristics, such as their difficulty and their discrimination power. We jointly model the discrimination and the difficulty parameters by using a k-component mixture of normal distributions. Mixture components correspond to disjoint groups of items. Items that belong to the same groups can be considered equivalent in terms of both difficulty and discrimination power. According to decision criteria, we select a subset of items such that the reduced questionnaire is able to provide the same information that the complete questionnaire provides. The model is estimated by using a Bayesian approach, and the choice of the number of mixture components is justified according to information criteria. We illustrate the proposed approach on the basis of data that are collected for 104 dysarthric patients by local health authorities in Lecce and in Milan. Copyright © 2014 John Wiley & Sons, Ltd.

Re-evaluating a vision-related quality of life questionnaire with item response theory (IRT and differential item functioning (DIF analyses

Directory of Open Access Journals (Sweden)

Knol Dirk L

2011-09-01

Full Text Available Abstract Background For the Low Vision Quality Of Life questionnaire (LVQOL it is unknown whether the psychometric properties are satisfactory when an item response theory (IRT perspective is considered. This study evaluates some essential psychometric properties of the LVQOL questionnaire in an IRT model, and investigates differential item functioning (DIF. Methods Cross-sectional data were used from an observational study among visually-impaired patients (n = 296. Calibration was performed for every dimension of the LVQOL in the graded response model. Item goodness-of-fit was assessed with the S-X2-test. DIF was assessed on relevant background variables (i.e. age, gender, visual acuity, eye condition, rehabilitation type and administration type with likelihood-ratio tests for DIF. The magnitude of DIF was interpreted by assessing the largest difference in expected scores between subgroups. Measurement precision was assessed by presenting test information curves; reliability with the index of subject separation. Results All items of the LVQOL dimensions fitted the model. There was significant DIF on several items. For two items the maximum difference between expected scores exceeded one point, and DIF was found on multiple relevant background variables. Item 1 'Vision in general' from the "Adjustment" dimension and item 24 'Using tools' from the "Reading and fine work" dimension were removed. Test information was highest for the "Reading and fine work" dimension. Indices for subject separation ranged from 0.83 to 0.94. Conclusions The items of the LVQOL showed satisfactory item fit to the graded response model; however, two items were removed because of DIF. The adapted LVQOL with 21 items is DIF-free and therefore seems highly appropriate for use in heterogeneous populations of visually impaired patients.

Laser manufacturing: strategies for dealing with the challenges

Science.gov (United States)

Barr, John R. M.

2012-09-01

Laser manufacturing in Edinburgh was initiated in 1963 by Ferranti (one of the previous names for SELEX Galileo). Since 2003 a modernized range of military lasers has been established. Innovation, both technical and in other aspects of the business, has enabled the design and manufacture of world leading laser designators and countermeasure lasers. Specific examples will be given including: the application of Geometric Algebra to resonator design; novel alignment free optical parametric oscillators; techniques for designing thermally insensitive laser diode pump heads; and methods for contamination control in lasers.

The design of impact absorbing structures for additive manufacture

International Nuclear Information System (INIS)

Brennan-Craddock, J; Brackett, D; Wildman, R; Hague, R

2012-01-01

Additive manufacturing (AM) is increasingly becoming a viable manufacturing process due to dramatic advantages that it facilitates in the area of design complexity. This paper investigates the potential of additively manufactured lattice structures for the application of tailored impact absorption specifically for conformal body protection. It explores lattice cell types based on foam microstructures and assesses their suitability for impact absorption. The effect of varying the cell strut edge design is also investigated. The implications of scaling these cells up for AM are discussed as well as the design issues regarding the handling of geometric complexity and the requirement for body conformity. The suitability of AM materials for this application is also discussed.

Assessment of the Item Selection and Weighting in the Birmingham Vasculitis Activity Score for Wegener's Granulomatosis

Science.gov (United States)

MAHR, ALFRED D.; NEOGI, TUHINA; LAVALLEY, MICHAEL P.; DAVIS, JOHN C.; HOFFMAN, GARY S.; MCCUNE, W. JOSEPH; SPECKS, ULRICH; SPIERA, ROBERT F.; ST.CLAIR, E. WILLIAM; STONE, JOHN H.; MERKEL, PETER A.

2013-01-01

Objective To assess the Birmingham Vasculitis Activity Score for Wegener's Granulomatosis (BVAS/WG) with respect to its selection and weighting of items. Methods This study used the BVAS/WG data from the Wegener's Granulomatosis Etanercept Trial. The scoring frequencies of the 34 predefined items and any “other” items added by clinicians were calculated. Using linear regression with generalized estimating equations in which the physician global assessment (PGA) of disease activity was the dependent variable, we computed weights for all predefined items. We also created variables for clinical manifestations frequently added as other items, and computed weights for these as well. We searched for the model that included the items and their generated weights yielding an activity score with the highest R2 to predict the PGA. Results We analyzed 2,044 BVAS/WG assessments from 180 patients; 734 assessments were scored during active disease. The highest R2 with the PGA was obtained by scoring WG activity based on the following items: the 25 predefined items rated on ≥5 visits, the 2 newly created fatigue and weight loss variables, the remaining minor other and major other items, and a variable that signified whether new or worse items were present at a specific visit. The weights assigned to the items ranged from 1 to 21. Compared with the original BVAS/WG, this modified score correlated significantly more strongly with the PGA. Conclusion This study suggests possibilities to enhance the item selection and weighting of the BVAS/WG. These changes may increase this instrument's ability to capture the continuum of disease activity in WG. PMID:18512722

The Accuracy of 3D Optical Reconstruction and Additive Manufacturing Processes in Reproducing Detailed Subject-Specific Anatomy

Directory of Open Access Journals (Sweden)

Paolo Ferraiuoli

2017-10-01

Full Text Available 3D reconstruction and 3D printing of subject-specific anatomy is a promising technology for supporting clinicians in the visualisation of disease progression and planning for surgical intervention. In this context, the 3D model is typically obtained from segmentation of magnetic resonance imaging (MRI, computed tomography (CT or echocardiography images. Although these modalities allow imaging of the tissues in vivo, assessment of quality of the reconstruction is limited by the lack of a reference geometry as the subject-specific anatomy is unknown prior to image acquisition. In this work, an optical method based on 3D digital image correlation (3D-DIC techniques is used to reconstruct the shape of the surface of an ex vivo porcine heart. This technique requires two digital charge-coupled device (CCD cameras to provide full-field shape measurements and to generate a standard tessellation language (STL file of the sample surface. The aim of this work was to quantify the error of 3D-DIC shape measurements using the additive manufacturing process. The limitations of 3D printed object resolution, the discrepancy in reconstruction of the surface of cardiac soft tissue and a 3D printed model of the same surface were evaluated. The results obtained demonstrated the ability of the 3D-DIC technique to reconstruct localised and detailed features on the cardiac surface with sub-millimeter accuracy.

Cloud manufacturing distributed computing technologies for global and sustainable manufacturing

CERN Document Server

Mehnen, Jörn

2013-01-01

Global networks, which are the primary pillars of the modern manufacturing industry and supply chains, can only cope with the new challenges, requirements and demands when supported by new computing and Internet-based technologies. Cloud Manufacturing: Distributed Computing Technologies for Global and Sustainable Manufacturing introduces a new paradigm for scalable service-oriented sustainable and globally distributed manufacturing systems.   The eleven chapters in this book provide an updated overview of the latest technological development and applications in relevant research areas.  Following an introduction to the essential features of Cloud Computing, chapters cover a range of methods and applications such as the factors that actually affect adoption of the Cloud Computing technology in manufacturing companies and new geometrical simplification method to stream 3-Dimensional design and manufacturing data via the Internet. This is further supported case studies and real life data for Waste Electrical ...

JIT Manufacturing: A Survey of Implementations in Small and Large U.S. Manufacturers

OpenAIRE

Richard E. White; John N. Pearson; Jeffrey R. Wilson

1999-01-01

Since the early 1980s, the diffusion of Just-In-Time (JIT) manufacturing from Japanese manufacturers to U.S. manufacturers has progressed at an accelerated rate. At this stage of the diffusion process, JIT implementations are more common and more advanced in large U.S. manufacturers than in small; consequently, U.S. businessmen's understanding of issues associated with JIT implementations in large manufacturers is more developed than that of small manufacturers. When small manufacturers repre...

Item response theory analysis of the life orientation test-revised: age and gender differential item functioning analyses.

Science.gov (United States)

Steca, Patrizia; Monzani, Dario; Greco, Andrea; Chiesi, Francesca; Primi, Caterina

2015-06-01

This study is aimed at testing the measurement properties of the Life Orientation Test-Revised (LOT-R) for the assessment of dispositional optimism by employing item response theory (IRT) analyses. The LOT-R was administered to a large sample of 2,862 Italian adults. First, confirmatory factor analyses demonstrated the theoretical conceptualization of the construct measured by the LOT-R as a single bipolar dimension. Subsequently, IRT analyses for polytomous, ordered response category data were applied to investigate the items' properties. The equivalence of the items across gender and age was assessed by analyzing differential item functioning. Discrimination and severity parameters indicated that all items were able to distinguish people with different levels of optimism and adequately covered the spectrum of the latent trait. Additionally, the LOT-R appears to be gender invariant and, with minor exceptions, age invariant. Results provided evidence that the LOT-R is a reliable and valid measure of dispositional optimism. © The Author(s) 2014.

Reconfigurable manufacturing system for agile mass customization manufacturing

CSIR Research Space (South Africa)

Xing, B

2006-07-01

Full Text Available Manufacturing companies are facing three challenges: low cost production of product, high quality standard and rapid responsiveness to customer requirements. These three goals are equally important for the manufacturing companies who want...

Racial differences in hypertension knowledge: effects of differential item functioning.

Science.gov (United States)

Ayotte, Brian J; Trivedi, Ranak; Bosworth, Hayden B

2009-01-01

Health-related knowledge is an important component in the self-management of chronic illnesses. The objective of this study was to more accurately assess racial differences in hypertension knowledge by using a latent variable modeling approach that controlled for sociodemographic factors and accounted for measurement issues in the assessment of hypertension knowledge. Cross-sectional data from 1,177 participants (45% African American; 35% female) were analyzed using a multiple indicator multiple causes (MIMIC) modeling approach. Available sociodemographic data included race, education, sex, financial status, and age. All participants completed six items on a hypertension knowledge questionnaire. Overall, the final model suggested that females, Whites, and patients with at least a high school diploma had higher latent knowledge scores than males, African Americans, and patients with less than a high school diploma, respectively. The model also detected differential item functioning (DIF) based on race for two of the items. Specifically, the error rate for African Americans was lower than would be expected given the lower level of latent knowledge on the items, on the questions related to: (a) the association between high blood pressure and kidney disease, and (b) the increased risk African Americans have for developing hypertension. Not accounting for DIF resulted in the difference between Whites and African Americans to be underestimated. These results are discussed in the context of the need for careful measurement of health-related constructs, and how measurement-related issues can result in an inaccurate estimation of racial differences in hypertension knowledge.

Manufacturing Initiative

Data.gov (United States)

National Aeronautics and Space Administration — The Advanced Manufacturing Technologies (AMT) Project supports multiple activities within the Administration's National Manufacturing Initiative. A key component of...

Design and manufacture of steam generators for replacement

International Nuclear Information System (INIS)

Hirano, Hiroshi; Kuri, Syuhei

1995-01-01

The basic specification of the steam generators for replacement as heat exchangers (the pressure, temperature, flow rate and thermal output on primary and secondary sides) is set same as that of steam generators before replacement, but the latest design reflecting the operation experience obtained so far and taking the countermeasures for preventing heating tube damage in it is adopted, such as the heating tubes made of TT 690 alloy, the tube support plates with four-lobe shape tube holes made of stainless steel, the stainless steel rest fittings of three in one set and so on. After the heating tube break accident in Mihama No. 2 plant, the quality control was further strengthened. The comparison of the specifications of the steam generators of respective plants before and after the replacement is shown. The main objective of improving steam generators is the heightening of the reliability of heating tubes against intergranular attack and primary water stress corrosion cracking. The improvements of heating tube material, tube support plate material, secondary side heat flow, the shape of tube holes of tube support plates, the method of expanding heating tubes, and vibration-controlling fittings are explained. As to the manufacturing procedure and quality control, the manufacture of raw materials, the build-up welding of tube plates, the manufacture of lower half shell plates, the tube hole making of support plates, the insection of outer cylinder, flow rate distribution plate. Support plates and heating tubes, the sealing welding and expanding of heating tubes, the fixing of rest fittings, the manufacture and fixing of water chamber cover, the manufacture of upper half shell, the fixing of parts inside it, the final joint and inspection are described. (K.I.)

2000 survey of window manufacturers on the subject of switchable glass

Science.gov (United States)

LaPointe, Michael R.; Sottile, Gregory M.

2001-11-01

The results of a 2000 survey of United States window manufacturers on the subject of switchable glass are discussed. The areas covered in this paper include awareness of the overall product category of switchable glass and various types of switchable glass, attitudes toward specific features of switchable glass, expectations for manufacturer production of such products, expectations for market penetration rates among end-product consumers, levels of price sensitivity among window manufacturers regarding switchable glass, and expectations for the pace of new product development within the window industry over the next five years.

Safety procedures used during the manufacturing of amorphous silicon solar cells

Energy Technology Data Exchange (ETDEWEB)

Dickson, C R

1987-01-01

The Solarex Thin Film Division is a leader in the manufacturing of amorphous-silicon products for sale in domestic and foreign markets. Similarly, Solarex assumes a leadership role in recognizing the importance of safety in a manufacturing environment. Although many of the safety issues are similar to those in the semiconductor industry, this paper presents topics specific to amorphous silicon technology and the manufacturing ,f amorphous-silicon products. These topics are deposition of conducting transparent oxides (CTOs), amorphous silicon deposition, laser scribing, processing chemicals, fire prevention and administrative responsibilities.

NASA's National Center for Advanced Manufacturing

Science.gov (United States)

Vickers, John

2003-01-01

NASA has designated the Principal Center Assignment to the Marshall Space Flight Center (MSFC) for implementation of the National Center for Advanced Manufacturing (NCAM). NCAM is NASA s leading resource for the aerospace manufacturing research, development, and innovation needs that are critical to the goals of the Agency. Through this initiative NCAM s people work together with government, industry, and academia to ensure the technology base and national infrastructure are available to develop innovative manufacturing technologies with broad application to NASA Enterprise programs, and U.S. industry. Educational enhancements are ever-present within the NCAM focus to promote research, to inspire participation and to support education and training in manufacturing. Many important accomplishments took place during 2002. Through NCAM, NASA was among five federal agencies involved in manufacturing research and development (R&D) to launch a major effort to exchange information and cooperate directly to enhance the payoffs from federal investments. The Government Agencies Technology Exchange in Manufacturing (GATE-M) is the only active effort to specifically and comprehensively address manufacturing R&D across the federal government. Participating agencies include the departments of Commerce (represented by the National Institute of Standards and Technology), Defense, and Energy, as well as the National Science Foundation and NASA. MSFC s ongoing partnership with the State of Louisiana, the University of New Orleans, and Lockheed Martin Corporation at the Michoud Assembly Facility (MAF) progressed significantly. Major capital investments were initiated for world-class equipment additions including a universal friction stir welding system, composite fiber placement machine, five-axis machining center, and ten-axis laser ultrasonic nondestructive test system. The NCAM consortium of five universities led by University of New Orleans with Mississippi State University

Software Note: Using BILOG for Fixed-Anchor Item Calibration

Science.gov (United States)

DeMars, Christine E.; Jurich, Daniel P.

2012-01-01

The nonequivalent groups anchor test (NEAT) design is often used to scale item parameters from two different test forms. A subset of items, called the anchor items or common items, are administered as part of both test forms. These items are used to adjust the item calibrations for any differences in the ability distributions of the groups taking…

Do animals and furniture items elicit different brain responses in human infants?

Science.gov (United States)

Jeschonek, Susanna; Marinovic, Vesna; Hoehl, Stefanie; Elsner, Birgit; Pauen, Sabina

2010-11-01

One of the earliest categorical distinctions to be made by preverbal infants is the animate-inanimate distinction. To explore the neural basis for this distinction in 7-8-month-olds, an equal number of animal and furniture pictures was presented in an ERP-paradigm. The total of 118 pictures, all looking different from each other, were presented in a semi-randomized order for 1000ms each. Infants' brain responses to exemplars from both categories differed systematically regarding the negative central component (Nc: 400-600ms) at anterior channels. More specifically, the Nc was enhanced for animals in one subgroup of infants, and for furniture items in another subgroup of infants. Explorative analyses related to categorical priming further revealed category-specific differences in brain responses in the late time window (650-1550ms) at right frontal channels: Unprimed stimuli (preceded by a different-category item) elicited a more positive response as compared to primed stimuli (preceded by a same-category item). In sum, these findings suggest that the infant's brain discriminates exemplars from both global domains. Given the design of our task, we conclude that processes of category identification are more likely to account for our findings than processes of on-line category formation during the experimental session. Copyright © 2009 Elsevier B.V. All rights reserved.

Commercial grade item (CGI) dedication of generators for nuclear safety related applications

International Nuclear Information System (INIS)

Das, R.K.; Hajos, L.G.

1993-01-01

The number of nuclear safety related equipment suppliers and the availability of spare and replacement parts designed specifically for nuclear safety related application are shrinking rapidly. These have made it necessary for utilities to apply commercial grade spare and replacement parts in nuclear safety related applications after implementing proper acceptance and dedication process to verify that such items conform with the requirements of their use in nuclear safety related application. The general guidelines for the commercial grade item (CGI) acceptance and dedication are provided in US Nuclear Regulatory Commission (NRC) Generic Letters and Electric Power Research Institute (EPRI) Report NP-5652, Guideline for the Utilization of Commercial Grade Items in Nuclear Safety Related Applications. This paper presents an application of these generic guidelines for procurement, acceptance, and dedication of a commercial grade generator for use as a standby generator at Salem Generating Station Units 1 and 2. The paper identifies the critical characteristics of the generator which once verified, will provide reasonable assurance that the generator will perform its intended safety function. The paper also delineates the method of verification of the critical characteristics through tests and provide acceptance criteria for the test results. The methodology presented in this paper may be used as specific guidelines for reliable and cost effective procurement and dedication of commercial grade generators for use as standby generators at nuclear power plants

Designing modular manufacturing systems using mass customisation theories and methods

DEFF Research Database (Denmark)

Jørgensen, Steffen Nordahl; Hvilshøj, Mads; Madsen, Ole

2012-01-01

Today, manufacturing systems are developed as engineered to order (ETO) solutions tailored to produce a specific product or a limited product mix. However, such dedicated systems are not consistent with the current market demands for rapid product changes, high product variety, and customisation....... In response, modular manufacturing systems (MMS) are evolving, which are aimed to possess the required responsiveness and to be the manufacturing paradigm of mass customisation (MC). Hereby, MMS brings the development process of manufacturing systems against configured to order (CTO). Up to now, research...... in MMS has primarily focused on potential benefits, basic principles, and enabling technologies, while the approaches of actually designing and creating modular architectures have received less attention. A potential to fill these gaps by applying MC theories and methods is identified based...

Inventions on presenting textual items in Graphical User Interface

OpenAIRE

Mishra, Umakant

2014-01-01

Although a GUI largely replaces textual descriptions by graphical icons, the textual items are not completely removed. The textual items are inevitably used in window titles, message boxes, help items, menu items and popup items. Textual items are necessary for communicating messages that are beyond the limitation of graphical messages. However, it is necessary to harness the textual items on the graphical interface in such a way that they complement each other to produce the best effect. One...

Science Library of Test Items. Volume Eighteen. A Collection of Multiple Choice Test Items Relating Mainly to Chemistry.

Science.gov (United States)

New South Wales Dept. of Education, Sydney (Australia).

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items are made available to teachers for the construction of unit tests or term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The test items meet syllabus…

Science Library of Test Items. Volume Seventeen. A Collection of Multiple Choice Test Items Relating Mainly to Biology.

Science.gov (United States)

New South Wales Dept. of Education, Sydney (Australia).

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items are made available to teachers for the construction of unit tests or term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The test items meet syllabus…

Science Library of Test Items. Volume Nineteen. A Collection of Multiple Choice Test Items Relating Mainly to Geology.

Science.gov (United States)

New South Wales Dept. of Education, Sydney (Australia).

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items are made available to teachers for the construction of unit tests or term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The test items meet syllabus…

Self-supporting rhombic infill structures for additive manufacturing

DEFF Research Database (Denmark)

Wu, Jun; Wang, Charlie C.L.; Zhang, Xiaoting

2016-01-01

Recent work has demonstrated that the interior material layout of a 3D model can be designed to make a fabricated replica satisfy application-specific demands on its physical properties, such as resistance to external loads. A widely used practice to fabricate such models is by layer-based additive...... manufacturing (AM), which however suffers from the problem of adding and removing interior supporting structures. In this paper, we present a novel method for generating application-specific infill structures on rhombic cells so that the resultant structures can automatically satisfy manufacturing requirements...... on overhang-angle and wall-thickness. Additional supporting structures can be avoided entirely in our framework. To achieve this, we introduce the usage of an adaptive rhombic grid, which is built from an input surface model. Starting from the initial sparse set of rhombic cells, via numerical optimization...

Memory for Items and Relationships among Items Embedded in Realistic Scenes: Disproportionate Relational Memory Impairments in Amnesia

Science.gov (United States)

Hannula, Deborah E.; Tranel, Daniel; Allen, John S.; Kirchhoff, Brenda A.; Nickel, Allison E.; Cohen, Neal J.

2014-01-01

Objective The objective of this study was to examine the dependence of item memory and relational memory on medial temporal lobe (MTL) structures. Patients with amnesia, who either had extensive MTL damage or damage that was relatively restricted to the hippocampus, were tested, as was a matched comparison group. Disproportionate relational memory impairments were predicted for both patient groups, and those with extensive MTL damage were also expected to have impaired item memory. Method Participants studied scenes, and were tested with interleaved two-alternative forced-choice probe trials. Probe trials were either presented immediately after the corresponding study trial (lag 1), five trials later (lag 5), or nine trials later (lag 9) and consisted of the studied scene along with a manipulated version of that scene in which one item was replaced with a different exemplar (item memory test) or was moved to a new location (relational memory test). Participants were to identify the exact match of the studied scene. Results As predicted, patients were disproportionately impaired on the test of relational memory. Item memory performance was marginally poorer among patients with extensive MTL damage, but both groups were impaired relative to matched comparison participants. Impaired performance was evident at all lags, including the shortest possible lag (lag 1). Conclusions The results are consistent with the proposed role of the hippocampus in relational memory binding and representation, even at short delays, and suggest that the hippocampus may also contribute to successful item memory when items are embedded in complex scenes. PMID:25068665

Technological assessment of local manufacturers for wind turbine blade manufacturing in Pakistan

Science.gov (United States)

Mahmood, Khurram; Haroon, General

2012-11-01

Composite materials manufacturing industry is one of the world's hi-tech industry. Manufacturing of wind turbine blades is one of the specialized fields requiring high degree of precision and composite manufacturing techniques. This paper identifies the industries specializing in the composite manufacturing and is able to manufacture wind turbines blades in Pakistan. In the second phase, their technology readiness level is determined, based on some factors and then a readiness level are assigned to them. The assigned technology readiness level will depict the absorptive capacity of each manufacturing unit and its capability to take on such projects. The individual readiness level of manufacturing unit will then be used to establish combined technology readiness level of Pakistan particularly for wind turbine blades manufacturing. The composite manufacturing industry provides many spin offs and a diverse range of products can be manufactured using this facility. This research will be helpful to categorize the strong points and flaws of local industry for the gap analysis. It can also be used as a prerequisite study before the evaluation of technologies and specialties to improve the industry of the country for the most favorable results. This will form a basic data base which can be used for the decision making related to transfer of technology, training of local skilled workers and general up-gradation of the local manufacturing units.

Reducing of Manufacturing Lead Time by Implementation of Lean Manufacturing Principles

Directory of Open Access Journals (Sweden)

Hussein Salem Ketan

2015-08-01

Full Text Available Many organizations today are interesting to implementing lean manufacturing principles that should enable them to eliminating the wastes to reducing a manufacturing lead time. This paper concentrates on increasing the competitive level of the company in globalization markets and improving of the productivity by reducing the manufacturing lead time. This will be by using the main tool of lean manufacturing which is value stream mapping (VSM to identifying all the activities of manufacturing process (value and non-value added activities to reducing elimination of wastes (non-value added activities by converting a manufacturing system to pull instead of push by applying some of pull system strategies as kanban and first on first out lane (FIFO. ARENA software is used to simulate the current and future state. This work is executed in the state company for electrical industries in Baghdad. The obtained results of the application showed that implementation of lean principles helped on reducing of a manufacturing lead time by 33%.

Applying Hierarchical Model Calibration to Automatically Generated Items.

Science.gov (United States)

Williamson, David M.; Johnson, Matthew S.; Sinharay, Sandip; Bejar, Isaac I.

This study explored the application of hierarchical model calibration as a means of reducing, if not eliminating, the need for pretesting of automatically generated items from a common item model prior to operational use. Ultimately the successful development of automatic item generation (AIG) systems capable of producing items with highly similar…

41 CFR 101-27.404 - Review of items.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Review of items. 101-27.404 Section 101-27.404 Public Contracts and Property Management Federal Property Management...-Elimination of Items From Inventory § 101-27.404 Review of items. Except for standby or reserve stocks, items...

Towards an authoring system for item construction

NARCIS (Netherlands)

Rikers, Jos H.A.N.

1988-01-01

The process of writing test items is analyzed, and a blueprint is presented for an authoring system for test item writing to reduce invalidity and to structure the process of item writing. The developmental methodology is introduced, and the first steps in the process are reported. A historical

Modeling Local Item Dependence in Cloze and Reading Comprehension Test Items Using Testlet Response Theory

Science.gov (United States)

Baghaei, Purya; Ravand, Hamdollah

2016-01-01

In this study the magnitudes of local dependence generated by cloze test items and reading comprehension items were compared and their impact on parameter estimates and test precision was investigated. An advanced English as a foreign language reading comprehension test containing three reading passages and a cloze test was analyzed with a…

Design for additive bio-manufacturing : From patient-specific medical devices to rationally designed meta-biomaterials

NARCIS (Netherlands)

Zadpoor, A.A.

2017-01-01

Recent advances in additive manufacturing (AM) techniques in terms of accuracy, reliability, the range of processable materials, and commercial availability have made them promising candidates for production of functional parts including those used in the biomedical industry. The