Determining the optimal system-specific cut-off frequencies for filtering in-vitro upper extremity impact force and acceleration data by residual analysis.

Science.gov (United States)

Burkhart, Timothy A; Dunning, Cynthia E; Andrews, David M

2011-10-13

The fundamental nature of impact testing requires a cautious approach to signal processing, to minimize noise while preserving important signal information. However, few recommendations exist regarding the most suitable filter frequency cut-offs to achieve these goals. Therefore, the purpose of this investigation is twofold: to illustrate how residual analysis can be utilized to quantify optimal system-specific filter cut-off frequencies for force, moment, and acceleration data resulting from in-vitro upper extremity impacts, and to show how optimal cut-off frequencies can vary based on impact condition intensity. Eight human cadaver radii specimens were impacted with a pneumatic impact testing device at impact energies that increased from 20J, in 10J increments, until fracture occurred. The optimal filter cut-off frequency for pre-fracture and fracture trials was determined with a residual analysis performed on all force and acceleration waveforms. Force and acceleration data were filtered with a dual pass, 4th order Butterworth filter at each of 14 different cut-off values ranging from 60Hz to 1500Hz. Mean (SD) pre-fracture and fracture optimal cut-off frequencies for the force variables were 605.8 (82.7)Hz and 513.9 (79.5)Hz, respectively. Differences in the optimal cut-off frequency were also found between signals (e.g. Fx (medial-lateral), Fy (superior-inferior), Fz (anterior-posterior)) within the same test. These optimal cut-off frequencies do not universally agree with the recommendations of filtering all upper extremity impact data using a cut-off frequency of 600Hz. This highlights the importance of quantifying the filter frequency cut-offs specific to the instrumentation and experimental set-up. Improper digital filtering may lead to erroneous results and a lack of standardized approaches makes it difficult to compare findings of in-vitro dynamic testing between laboratories. Copyright © 2011 Elsevier Ltd. All rights reserved.

Derivation of the cut-off length from the quantum quadratic enhancement of a mass in vacuum energy constant Lambda

Science.gov (United States)

Fukushima, Kimichika; Sato, Hikaru

2018-04-01

Ultraviolet self-interaction energies in field theory sometimes contain meaningful physical quantities. The self-energies in such as classical electrodynamics are usually subtracted from the rest mass. For the consistent treatment of energies as sources of curvature in the Einstein field equations, this study includes these subtracted self-energies into vacuum energy expressed by the constant Lambda (used in such as Lambda-CDM). In this study, the self-energies in electrodynamics and macroscopic classical Einstein field equations are examined, using the formalisms with the ultraviolet cut-off scheme. One of the cut-off formalisms is the field theory in terms of the step-function-type basis functions, developed by the present authors. The other is a continuum theory of a fundamental particle with the same cut-off length. Based on the effectiveness of the continuum theory with the cut-off length shown in the examination, the dominant self-energy is the quadratic term of the Higgs field at a quantum level (classical self-energies are reduced to logarithmic forms by quantum corrections). The cut-off length is then determined to reproduce today's tiny value of Lambda for vacuum energy. Additionally, a field with nonperiodic vanishing boundary conditions is treated, showing that the field has no zero-point energy.

Neural Network Modeling of Cutting Fluid Impact on Energy Consumption during Turning

Directory of Open Access Journals (Sweden)

M. Bachraty

2016-06-01

Full Text Available This paper presents a part of research on power consumption differences between various cutting fluids used during turning operations. An attempt was made to study the possibility of artificial neural network to model the behavior function and predicting the electrical power consumption. Friction factor of examined cutting fluids was also measured to describe a more complete picture of investigated cutting fluids characteristics. It was discovered that wide spectrum of characteristics is present in today’s market and that artificial neural networks are suitable for purpose of modeling the power consumption of the lathe during machining. This paper could be used as a foundation for later database building where it would be possible to predict how certain cutting fluid will behave in a specific machining parameter combination.

Effects of Different Cutting Patterns and Experimental Conditions on the Performance of a Conical Drag Tool

Science.gov (United States)

Copur, Hanifi; Bilgin, Nuh; Balci, Cemal; Tumac, Deniz; Avunduk, Emre

2017-06-01

This study aims at determining the effects of single-, double-, and triple-spiral cutting patterns; the effects of tool cutting speeds on the experimental scale; and the effects of the method of yield estimation on cutting performance by performing a set of full-scale linear cutting tests with a conical cutting tool. The average and maximum normal, cutting and side forces; specific energy; yield; and coarseness index are measured and compared in each cutting pattern at a 25-mm line spacing, at varying depths of cut per revolution, and using two cutting speeds on five different rock samples. The results indicate that the optimum specific energy decreases by approximately 25% with an increasing number of spirals from the single- to the double-spiral cutting pattern for the hard rocks, whereas generally little effect was observed for the soft- and medium-strength rocks. The double-spiral cutting pattern appeared to be more effective than the single- or triple-spiral cutting pattern and had an advantage of lower side forces. The tool cutting speed had no apparent effect on the cutting performance. The estimation of the specific energy by the yield based on the theoretical swept area was not significantly different from that estimated by the yield based on the muck weighing, especially for the double- and triple-spiral cutting patterns and with the optimum ratio of line spacing to depth of cut per revolution. This study also demonstrated that the cutterhead and mechanical miner designs, semi-theoretical deterministic computer simulations and empirical performance predictions and optimization models should be based on realistic experimental simulations. Studies should be continued to obtain more reliable results by creating a larger database of laboratory tests and field performance records for mechanical miners using drag tools.

Rise time of proton cut-off energy in 2D and 3D PIC simulations

Science.gov (United States)

Babaei, J.; Gizzi, L. A.; Londrillo, P.; Mirzanejad, S.; Rovelli, T.; Sinigardi, S.; Turchetti, G.

2017-04-01

The Target Normal Sheath Acceleration regime for proton acceleration by laser pulses is experimentally consolidated and fairly well understood. However, uncertainties remain in the analysis of particle-in-cell simulation results. The energy spectrum is exponential with a cut-off, but the maximum energy depends on the simulation time, following different laws in two and three dimensional (2D, 3D) PIC simulations so that the determination of an asymptotic value has some arbitrariness. We propose two empirical laws for the rise time of the cut-off energy in 2D and 3D PIC simulations, suggested by a model in which the proton acceleration is due to a surface charge distribution on the target rear side. The kinetic energy of the protons that we obtain follows two distinct laws, which appear to be nicely satisfied by PIC simulations, for a model target given by a uniform foil plus a contaminant layer that is hydrogen-rich. The laws depend on two parameters: the scaling time, at which the energy starts to rise, and the asymptotic cut-off energy. The values of the cut-off energy, obtained by fitting 2D and 3D simulations for the same target and laser pulse configuration, are comparable. This suggests that parametric scans can be performed with 2D simulations since 3D ones are computationally very expensive, delegating their role only to a correspondence check. In this paper, the simulations are carried out with the PIC code ALaDyn by changing the target thickness L and the incidence angle α, with a fixed a0 = 3. A monotonic dependence, on L for normal incidence and on α for fixed L, is found, as in the experimental results for high temporal contrast pulses.

Assessment of abrasiveness for research of rock cutting

Directory of Open Access Journals (Sweden)

Milan Labaš

2012-12-01

Full Text Available Rock abrasiveness is ability of rock to wear down the working tool during the mutual interaction between the working indentorand the rock in the mechanical rock cutting process. The cutting indentor is worn down during the interaction, which changes itsgeometric dimensions causing the enlargement of a contact area between the tool and the rock surface. The changes in these dimensionsconsequently alter the rate of advance of the drilling machine and the specific cutting energy. We have determined the abrasivenessaccording to the norm ON 44 1121 (1982 on the testing device constructed at the Institute of Geotechnics SAS.

Influence of anatomy and basic density on specific cutting force for wood from Corymbia citriodora Hill & Johnson

Directory of Open Access Journals (Sweden)

Luiz-E. de L. Melo

2015-12-01

Full Text Available Aim of the study: The aim of this study was to evaluate the influence of xylem tissue cell structure, determined through biometry and basic density of the wood from Corymbia citriodora Hill & Johnson on consumption of specific 90º-0º longitudinal cutting force.Area of study: The study area was in the region of the Vale do Rio Doce - Minas Gerais, Brazil.Material and methods: A diametrical board with dimensions of 60 x 18 x 5 cm (length x width x thickness, respectively, with more than 1.3 m from the ground, was removed. In machining trials, a 400 mm diameter circular saw was used, with 24 “WZ” teeth, feed rate of 10 m.min-1, cutting speed of 61 m.s-1, and maximum instantaneous torque of 92.5 N.m. During cutting, test specimens were removed with alternated and parallel 1.5 cm edges in 6 radial positions, which were used for biometric determination of cell structure and basic density.Main results: It was observed that wood basic density, vessel diameter, fiber wall thickness, fiber wall fraction and fiber wall portion were directly proportional to the specific cutting force. In contrast, vessel frequency and fiber lumen diameter proved to be inversely proportional to cutting force.Research highlights: This work provides important values of quantification of influence of xylem tissue cell structure, determined through biometry and physical properties of the wood that may be used to prediction of consumption of specific cutting force.Keywords: wood machining; wood properties; optimization of the process.

Experimental study on variations in Charpy impact energies of low carbon steel, depending on welding and specimen cutting method

Energy Technology Data Exchange (ETDEWEB)

Yang, Zhaorui; Kang, Hansaem; Lee, Young Seog [Chung-Ang University, Seoul (Korea, Republic of)

2016-05-15

This paper presents an experimental study that examines variations of Charpy impact energy of a welded steel plate, depending upon the welding method and the method for obtaining the Charpy specimens. Flux cored arc welding (FCAW) and Gas tungsten arc welding (GTAW) were employed to weld an SA516 Gr. 70 steel plate. The methods of wire cutting and water-jet cutting were adopted to take samples from the welded plate. The samples were machined according to the recommendations of ASTM SEC. II SA370, in order to fit the specimen dimension that the Charpy impact test requires. An X-ray diffraction (XRD) method was used to measure the as-weld residual stress and its redistribution after the samples were cut. The Charpy impact energy of specimens was considerably dependent on the cutting methods and locations in the welded plate where the specimens were taken. The specimens that were cut by water jet followed by FCAW have the greatest resistance-to-fracture (Charpy impact energy). Regardless of which welding method was used, redistributed transverse residual stress becomes compressive when the specimens are prepared using water-jet cutting. Meanwhile, redistributed transverse residual stress becomes tensile when the specimens are prepared using wire cutting.

Laser cutting of laminated sheet material: a modeling exercise

Science.gov (United States)

de Graaf, Roelof F.; Meijer, Johan

1997-08-01

Laser cutting has been investigated for a number of aluminum-synthetic laminates, newly developed materials for the aeronautic and automotive industry. The materials consist of alternating aluminum and synthetic layers. It is shown that these materials can be cut at rates comparable to those of homogeneous aluminum alloys. The cuts show little dross attachment. Also some damage on the synthetic layers has to be accepted. These results initiated a modeling exercise, which resulted in a numerical simulation code. The applied cutting model is based on describing the material in several horizontal layers, each with its own specific thermophysical and optical properties. The separate layers are coupled by known mass, energy and force balanced equations.

Standard Specification for Steel Blades Used with the Photovoltaic Module Surface Cut Test

CERN Document Server

American Society for Testing and Materials. Philadelphia

2009-01-01

1.1 This specification specifies the recommended physical characteristics of the steel blades required for the surface cut test described in ANSI/UL 1703 (Section 24) and IEC 61730-2 (Paragraph 10.3). 1.2 ANSI/UL 1703 and IEC 61730-2 are standards for photovoltaic module safety testing. 1.3 This standard provides additional fabrication details for the surface cut test blades that are not provided in ANSI/UL 1703 or IEC 61730-2. Surface cut test blades that have out-of-tolerance corner radii or burrs are known to cause erroneous test results, either passes or failures. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Analyses of Effects of Cutting Parameters on Cutting Edge Temperature Using Inverse Heat Conduction Technique

Directory of Open Access Journals (Sweden)

Marcelo Ribeiro dos Santos

2014-01-01

Full Text Available During machining energy is transformed into heat due to plastic deformation of the workpiece surface and friction between tool and workpiece. High temperatures are generated in the region of the cutting edge, which have a very important influence on wear rate of the cutting tool and on tool life. This work proposes the estimation of heat flux at the chip-tool interface using inverse techniques. Factors which influence the temperature distribution at the AISI M32C high speed steel tool rake face during machining of a ABNT 12L14 steel workpiece were also investigated. The temperature distribution was predicted using finite volume elements. A transient 3D numerical code using irregular and nonstaggered mesh was developed to solve the nonlinear heat diffusion equation. To validate the software, experimental tests were made. The inverse problem was solved using the function specification method. Heat fluxes at the tool-workpiece interface were estimated using inverse problems techniques and experimental temperatures. Tests were performed to study the effect of cutting parameters on cutting edge temperature. The results were compared with those of the tool-work thermocouple technique and a fair agreement was obtained.

N=4 supersymmetric Yang Mills scattering amplitudes at high energies. The Regge cut contribution

International Nuclear Information System (INIS)

Bartels, J.; Sabio Vera, A.

2008-07-01

We further investigate, in N=4 supersymmetric Yang Mills theories, the high energy Regge behavior of six-point scattering amplitudes. In particular, for the new Regge cut contribution found in our previous paper, we compute in the leading logarithmic approximation (LLA) the energy spectrum of the BFKL equation in the color octet channel, and we calculate explicitly the two loop corrections to the discontinuities of the amplitudes for the transitions 2→4 and 3→3. We find an explicit solution of the BFKL equation for the octet channel for arbitrary momentum transfers and investigate the intercepts of the Regge singularities in this channel. As an important result we find that the universal collinear and infrared singularities of the BDS formula are not affected by this Regge-cut contribution. (orig.)

Energy technologies at the cutting edge: international energy technology collaboration IEA Implementing Agreements

Energy Technology Data Exchange (ETDEWEB)

Pottinger, C. (ed.)

2007-05-15

Ensuring energy security and addressing climate change issues in a cost-effective way are the main challenges of energy policies and in the longer term will be solved only through technology cooperation. To encourage collaborative efforts to meet these energy challenges, the IEA created a legal contract - Implementing Agreement - and a system of standard rules and regulations. This allows interested member and non-member governments or other organisations to pool resources and to foster the research, development and deployment of particular technologies. For more than 30 years, this international technology collaboration has been a fundamental building block in facilitating progress of new or improved energy technologies. There are now 41 Implementing Agreements. This is the third in the series of publications highlighting the recent results and achievements of the IEA Implementing Agreements. This document is arranged in the following sections: Cross-cutting activities (sub-sectioned: Climate technology initiative; Energy Technology Data Eexchange; and Energy technology systems analysis programme); End-use technologies (sub-sectioned: Buildings; Electricity; Industry; and Transport; Fossil fuels (sub-sectioned: Clean Coal Centre; Enhanced oil recovery Fluidized bed conversion; Greenhouse Gas R & D; Multiphase flow sciences); Fusion power; Renewable energies and hydrogen; and For more information (including detail on the IEA energy technology network; IEA Secretariat Implementing Agreement support; and IEA framework. Addresses are given for the Implementing Agreements. The publication is based on core input from the Implementing Agreement Executive Committee.

Note: Laser-cut molybdenum grids for a retarding field energy analyzer

Science.gov (United States)

Landheer, K.; Kobelev, A. A.; Smirnov, A. S.; Bosman, J.; Deelen, S.; Rossewij, M.; de Waal, A. C.; Poulios, I.; Benschop, A. F.; Schropp, R. E. I.; Rath, J. K.

2017-06-01

A retarding field energy analyzer (RFEA) with grids created by laser-cutting a honeycomb mesh in a 50 μm thick molybdenum foil is presented. The flat grids span an area of 1 cm2 and have high transmission (20 μm wide walls between 150 μm wide meshes). The molybdenum grids were tested in a 3-grid RFEA configuration with an analyzer depth of 0.87 mm.

Potential recovery of industrial wood and energy wood raw material in different cutting and climate scenarios for Finland

International Nuclear Information System (INIS)

Kaerkkaeinen, Leena; Nuutinen, Tuula; Matala, Juho; Kellomaeki, Seppo; Haerkoenen, Kari

2008-01-01

The aim of this study was to estimate the simultaneous recovery of industrial wood and raw material for energy wood from cuttings in Finland during the next 50 years. Two cutting scenarios (maximum and sustainable cuttings) and two climate scenarios (current and changing climate) were analysed to determine their impacts on harvesting potential. The analysis was carried out using sample plot and tree data from the ninth National Forest Inventory and a management-oriented large-scale forestry model (MELA) into which the transfer functions based on physiological modelling were incorporated to describe the impacts of climate change. Depending on the climate scenario, the volume of potential recovery of industrial wood in the maximum cutting scenario during the period 2003-2013 varied from 103 to 105 million m 3 a -1 , while the amount of potential energy wood raw material was 35 Tg a -1 . During the period 2043-2053, in the current climate scenario, the potential recovery of industrial wood was 64 million m 3 a -1 and energy wood raw material 22 Tg a -1 , and in the changing climate scenario, 85 million m 3 a -1 and 29 Tg a -1 , respectively. In the sustainable cutting scenario, depending on the climate scenario used, the potential recovery of industrial wood during the period 2003-2013 varied from 74 to 76 million m 3 a -1 , while the amount of potential energy wood was 25 Tg a -1 . During the period 2043-2053, in the current climate scenario, the potential recovery of industrial wood was 80 million m 3 a -1 and energy wood raw material 26 Tg a -1 , and in the changing climate scenario, 88 million m 3 a -1 and 29 Tg a -1 , respectively. (author)

Segmentation of Synchrotron Radiation micro-Computed Tomography Images using Energy Minimization via Graph Cuts

International Nuclear Information System (INIS)

Meneses, Anderson A.M.; Giusti, Alessandro; Almeida, André P. de; Nogueira, Liebert; Braz, Delson; Almeida, Carlos E. de; Barroso, Regina C.

2012-01-01

The research on applications of segmentation algorithms to Synchrotron Radiation X-Ray micro-Computed Tomography (SR-μCT) is an open problem, due to the interesting and well-known characteristics of SR images, such as the phase contrast effect. The Energy Minimization via Graph Cuts (EMvGC) algorithm represents state-of-art segmentation algorithm, presenting an enormous potential of application in SR-μCT imaging. We describe the application of the algorithm EMvGC with swap move for the segmentation of bone images acquired at the ELETTRA Laboratory (Trieste, Italy). - Highlights: ► Microstructures of Wistar rats' ribs are investigated with Synchrotron Radiation μCT imaging. ► The present work is part of a research on the effects of radiotherapy on the thoracic region. ► Application of the Energy Minimization via Graph Cuts algorithm for segmentation is described.

Modified GrabCut for human face segmentation

Directory of Open Access Journals (Sweden)

Dina Khattab

2014-12-01

Full Text Available GrabCut is a segmentation technique for 2D still color images, which is mainly based on an iterative energy minimization. The energy function of the GrabCut optimization algorithm is based mainly on a probabilistic model for pixel color distribution. Therefore, GrabCut may introduce unacceptable results in the cases of low contrast between foreground and background colors. In this manner, this paper presents a modified GrabCut technique for the segmentation of human faces from images of full humans. The modified technique introduces a new face location model for the energy minimization function of the GrabCut, in addition to the existing color one. This location model considers the distance distribution of the pixels from the silhouette boundary of a fitted head, of a 3D morphable model, to the image. The experimental results of the modified GrabCut have demonstrated better segmentation robustness and accuracy compared to the original GrabCut for human face segmentation.

Metal cutting by radiation from a CO2 laser with a self-filtering cavity

International Nuclear Information System (INIS)

Malikov, A G; Orishich, Anatolii M; Shulyat'ev, Viktor B

2009-01-01

The possibility of quality cutting by radiation from a CO 2 laser with an unstable self-filtering cavity (SFC) is experimentally investigated. The SFC provides the product of the divergence angle by the beam radius close to that for lower modes in a stable cavity (SC), however, at a higher radiation power, which favours faster cutting. In the far-field zone, the SFC beam has a diffraction structure with side maxima, which is usually considered as a negative factor in laser cutting. 25-mm-thick steel slabs have been cut. The comparison of the obtained results with known data on SC lasers shows that the principal characteristics of the cut (the width, edge roughness, specific expenditure of energy) are close in these lasers. A conclusion is made that at the chosen cavity parameters, the specific spatial structure of the SFC laser beam has no significant effect on the cut characteristics. (laser technologies)

Test tube systems with cutting/recombination operations

Energy Technology Data Exchange (ETDEWEB)

Freund, R. [Technische Universitaet Wien (Austria); Csuhaj-Varju, E. [Computer and Automation Institute, Budapest (Hungary); Wachtler, F. [Universitaet Wien (Austria)

1996-12-31

We introduce test tube systems based on operations that are closely related to the splicing operations, i.e. we consider the operations of cutting a string at a specific site into two pieces with marking them at the cut ends and of recombining two strings with specifically marked endings. Whereas in the splicing of two strings these strings are cut at specific sites and the cut pieces are recombined immediately in a crosswise way, in CR(cutting/recombination)-schemes cutting can happen independently from recombining the cut pieces. Test tube systems based on these operations of cutting and recombination turn out to have maximal generative power even if only very restricted types of input filters for the test tubes are used for the redistribution of the contents of the test tubes after a period of cuttings and recombinations in the test tubes. 10 refs.

Segmentation of Synchrotron Radiation micro-Computed Tomography Images using Energy Minimization via Graph Cuts

Energy Technology Data Exchange (ETDEWEB)

Meneses, Anderson A.M. [Federal University of Western Para (Brazil); Physics Institute, Rio de Janeiro State University (Brazil); Giusti, Alessandro [IDSIA (Dalle Molle Institute for Artificial Intelligence), University of Lugano (Switzerland); Almeida, Andre P. de, E-mail: apalmeid@gmail.com [Physics Institute, Rio de Janeiro State University (Brazil); Nuclear Engineering Program, Federal University of Rio de Janeiro (Brazil); Nogueira, Liebert; Braz, Delson [Nuclear Engineering Program, Federal University of Rio de Janeiro (Brazil); Almeida, Carlos E. de [Radiological Sciences Laboratory, Rio de Janeiro State University (Brazil); Barroso, Regina C. [Physics Institute, Rio de Janeiro State University (Brazil)

2012-07-15

The research on applications of segmentation algorithms to Synchrotron Radiation X-Ray micro-Computed Tomography (SR-{mu}CT) is an open problem, due to the interesting and well-known characteristics of SR images, such as the phase contrast effect. The Energy Minimization via Graph Cuts (EMvGC) algorithm represents state-of-art segmentation algorithm, presenting an enormous potential of application in SR-{mu}CT imaging. We describe the application of the algorithm EMvGC with swap move for the segmentation of bone images acquired at the ELETTRA Laboratory (Trieste, Italy). - Highlights: Black-Right-Pointing-Pointer Microstructures of Wistar rats' ribs are investigated with Synchrotron Radiation {mu}CT imaging. Black-Right-Pointing-Pointer The present work is part of a research on the effects of radiotherapy on the thoracic region. Black-Right-Pointing-Pointer Application of the Energy Minimization via Graph Cuts algorithm for segmentation is described.

Non-Poissonian photon statistics from macroscopic photon cutting materials.

Science.gov (United States)

de Jong, Mathijs; Meijerink, Andries; Rabouw, Freddy T

2017-05-24

In optical materials energy is usually extracted only from the lowest excited state, resulting in fundamental energy-efficiency limits such as the Shockley-Queisser limit for single-junction solar cells. Photon-cutting materials provide a way around such limits by absorbing high-energy photons and 'cutting' them into multiple low-energy excitations that can subsequently be extracted. The occurrence of photon cutting or quantum cutting has been demonstrated in a variety of materials, including semiconductor quantum dots, lanthanides and organic dyes. Here we show that photon cutting results in bunched photon emission on the timescale of the excited-state lifetime, even when observing a macroscopic number of optical centres. Our theoretical derivation matches well with experimental data on NaLaF 4 :Pr 3+ , a material that can cut deep-ultraviolet photons into two visible photons. This signature of photon cutting can be used to identify and characterize new photon-cutting materials unambiguously.

Operation of the AM-50 cutting head under different cutting conditions

Energy Technology Data Exchange (ETDEWEB)

Sikora, W; Kusz, F; Fels, M

1988-02-01

Presents results of investigations into operation of the AM-50 heading machine. About 50% of headings, i.e. about 800 km/a, are driven by about 400 heading machines. It has been found that energy consumption depends on compression strength of rock and is 6 times higher for sandstone than for clayey shale. Power consumed by cutting heads depends mainly on the web used (30-150 mm depending on rock strength). Wear of cutting tools is 1-30 pieces per meter of heading advance at a working cross-section area of 15 m/sup 2/. The AM-50 machine uses cutting speeds of 1.1-3.5 m/s. Higher speeds negatively affect the resistance to cutting. Nonuniform tool wear on the cutting head circumference is an indication of improper head design that requires remedying.

The Impact of Feeding Diets of High or Low Energy Concentration on Carcass Measurements and the Weight of Primal and Subprimal Lean Cuts

Directory of Open Access Journals (Sweden)

A. P. Schinckel

2012-04-01

Full Text Available Pigs from four sire lines were allocated to a series of low energy (LE, 3.15 to 3.21 Mcal ME/kg corn-soybean meal-based diets with 16% wheat midds or high energy diets (HE, 3.41 to 3.45 Mcal ME/kg with 4.5 to 4.95% choice white grease. All diets contained 6% DDGS. The HE and LE diets of each of the four phases were formulated to have equal lysine:Mcal ME ratios. Barrows (N = 2,178 and gilts (N = 2,274 were fed either high energy (HE or low energy (LE diets from 27 kg BW to target BWs of 118, 127, 131.5 and 140.6 kg. Carcass primal and subprimal cut weights were collected. The cut weights and carcass measurements were fitted to allometric functions (Y = A CWB of carcass weight. The significance of diet, sex or sire line with A and B was evaluated by linearizing the equations by log to log transformation. The effect of diet on A and B did not interact with sex or sire line. Thus, the final model was B where Diet = −0.5 for the LE and 0.5 for HE diets and A and B are sire line-sex specific parameters. cut weight = (1+bD(Diet A(CW Diet had no affect on loin, Boston butt, picnic, baby back rib, or sparerib weights (p>0.10, bD = −0.003, −0.0029, 0.0002, 0.0047, −0.0025, respectively. Diet affected ham weight (bD = −0.0046, p = 0.01, belly weight (bD = 0.0188, p = 0.001 three-muscle ham weight (bD = −0.014, p = 0.001, boneless loin weight (bD = −0.010, p = 0.001, tenderloin weight (bD = −0.023, p = 0.001, sirloin weight (bD = −0.009, p = 0.034, and fat-free lean mass (bD = −0.0145, p = 0.001. Overall, feeding the LE diets had little impact on primal cut weight except to decrease belly weight. Feeding LE diets increased the weight of lean trimmed cuts by 1 to 2 percent at the same carcass weight.

How to achieve emission reductions in Germany and the European Union. Energy policy, RUE with cross cutting technologies, Pinch technology

Energy Technology Data Exchange (ETDEWEB)

Radgen, P.

1999-10-01

The German presentations will cover three main topics. These are: (1) Energy policy on the national level and in the European Community. (2) Rational use of energy and efficiency improvements by cross cutting technologies. (3) Optimizing heat recovery and heat recovery network with Pinch technology. Actual development of carbon dioxide emissions and scenarios to forecast for the future development will be presented. It will be shown, that long term agreements are widely used in the EC to obtain a reduction of emissions. Specific attention will also be placed on the burden sharing in the EC and the other GHG. In the second part the efficiency improvement by cross cutting technologies will be discussed for furnaces, waste heat recovery, electric motors, compressed air systems, cooling systems, lighting and heat pumps. Most of these improvement potentials are economic at present energy prices, but some barriers for their application have to be overcome which will be discussed. In the last part a systematic method for the optimization of heat recovery networks is presented. The Pinch technology, developed in the late seventies is an easy and reliable way to obtain quickly a good insight into the heat flows of a process. The basics of Pinch technology will be presented with a simple example and the presentation of an in deep analysis of a fertilizer complex. (orig.)

Institute a modest carbon tax to reduce carbon emissions, finance clean energy technology development, cut taxes, and reduce the deficit

Energy Technology Data Exchange (ETDEWEB)

Muro, Mark; Rothwell, Jonathan

2012-11-15

The nation should institute a modest carbon tax in order to help clean up the economy and stabilize the nation’s finances. Specifically, Congress and the president should implement a $20 per ton, steadily increasing carbon excise fee that would discourage carbon dioxide emissions while shifting taxation onto pollution, financing energy efficiency (EE) and clean technology development, and providing opportunities to cut taxes or reduce the deficit. The net effect of these policies would be to curb harmful carbon emissions, improve the nation’s balance sheet, and stimulate job-creation and economic renewal.

Leaf processing behaviour in Atta leafcutter ants: 90% of leaf cutting takes place inside the nest, and ants select pieces that require less cutting.

Science.gov (United States)

Garrett, Ryan W; Carlson, Katherine A; Goggans, Matthew Scott; Nesson, Michael H; Shepard, Christopher A; Schofield, Robert M S

2016-01-01

Leafcutter ants cut trimmings from plants, carry them to their underground nests and cut them into smaller pieces before inoculating them with a fungus that serves as a primary food source for the colony. Cutting is energetically costly, so the amount of cutting is important in understanding foraging energetics. Estimates of the cutting density, metres of cutting per square metre of leaf, were made from samples of transported leaf cuttings and of fungal substrate from field colonies of Atta cephalotes and Atta colombica. To investigate cutting inside the nest, we made leaf-processing observations of our laboratory colony, A. cephalotes. We did not observe the commonly reported reduction of the leaf fragments into a pulp, which would greatly increase the energy cost of processing. Video clips of processing behaviours, including behaviours that have not previously been described, are linked. An estimated 2.9 (±0.3) km of cutting with mandibles was required to reduce a square metre of leaf to fungal substrate. Only about 12% (±1%) of this cutting took place outside of the nest. The cutting density and energy cost is lower for leaf material with higher ratios of perimeter to area, so we tested for, and found that the laboratory ants had a preference for leaves that were pre-cut into smaller pieces. Estimates suggest that the energy required to transport and cut up the leaf material is comparable to the metabolic energy available from the fungus grown on the leaves, and so conservation of energy is likely to be a particularly strong selective pressure for leafcutter ants.

New Modelling Strategies For Metal Cutting

International Nuclear Information System (INIS)

Rosa, Pedro A. R.; Martins, Paulo A. F.; Atkins, Anthony G.

2007-01-01

This paper draws from the 'plasticity and friction only' view of metal cutting to the presentation of new modelling strategies based on the interaction between finite elements and modern ductile fracture mechanics. The overall presentation is supported by specially designed orthogonal metal cutting experiments that were performed on Lead test specimens under laboratory-controlled conditions. Comparisons between theoretical predictions and experimental results comprise a wide range of topics such as material flow, cutting forces and specific cutting pressure. The paper demonstrates that while material flow and chip formation can be successfully modelled by traditional 'plasticity and friction only' analyses, the contribution of the fracture work involved in the formation of new surfaces is essential for obtaining good estimates of cutting forces and of the specific cutting pressure

Dynamic simulation of cable shovel specific energy in oil sands excavation

Energy Technology Data Exchange (ETDEWEB)

Awuah-Offei, K. [Missouri-Rolla Univ., Rolla, MO (United States). School of Materials, Energy and Earth Resources; Frimpong, S. [Missouri-Rolla Univ., Rolla, MO (United States). Dept. of Mining Engineering, Mining and Nuclear Engineering; Askari-Nasab, H. [Alberta Univ., Edmonton, AB (Canada). School of Mining and Petroleum Engineering

2005-07-01

Oil sand excavation requires the use cable shovels which constitute one of the major costs in surface mining operations. Random occurrences of shales and limestones within the Athabasca oil sands formation result in varying shovel diggability and stress loading of the boom-crowd-dipper-teeth assembly which reduces digging efficiency. This inefficient use of cable shovels negatively affects the return on capital investment in these otherwise effective machines. In the Athabasca oil sands, varying stress loading has the potential to increase shovel downtime and increase maintenance costs. This paper presented a newly developed cable shovel simulator that uses shovel kinematics and dynamics, dynamic cutting resistance and payload models. It can model the specific energy needed to overcome the resistance to machine motion and material digging. The comprehensive model considers both machine motion and machine-formation interaction forces. It also provides a comprehensive theoretical assessment of shovel performance. The model is useful to mining engineers when examining both the machine operating parameters and material parameters that influence shovel performance. The study showed that bulk density is the most important material property influencing diggability. Operator preferences also influence the specific energy of excavation. 12 refs., 2 tabs., 6 figs.

Energy efficient process planning based on numerical simulations

OpenAIRE

Neugebauer, Reimund; Hochmuth, C.; Schmidt, G.; Dix, M.

2011-01-01

The main goal of energy-efficient manufacturing is to generate products with maximum value-added at minimum energy consumption. To this end, in metal cutting processes, it is necessary to reduce the specific cutting energy while, at the same time, precision requirements have to be ensured. Precision is critical in metal cutting processes because they often constitute the final stages of metalworking chains. This paper presents a method for the planning of energy-efficient machining processes ...

Economic technology of laser cutting

Science.gov (United States)

Fedin, Alexander V.; Shilov, Igor V.; Vassiliev, Vladimir V.; Malov, Dmitri V.; Peskov, Vladimir N.

2000-02-01

The laser cutting of color metals and alloys by a thickness more than 2 mm has significant difficulties due to high reflective ability and large thermal conduction. We made it possible to raise energy efficiency and quality of laser cutting by using a laser processing system (LPS) consisting both of the YAG:Nd laser with passive Q-switching on base of LiF:F2- crystals and the CO2 laser. A distinctive feature of the LPS is that the radiation of different lasers incorporated in a coaxial beam has simultaneously high level of peak power (more than 400 kW in a TEM00 mode) and significant level of average power (up to 800 W in a TEM01 mode of the CO2 laser). The application of combined radiation for cutting of an aluminum alloy of D16 type made it possible to decrease the cutting energy threshold in 1.7 times, to increase depth of treatment from 2 up to 4 mm, and velocity from 0.015 up to 0.7 m/min, and also to eliminate application of absorptive coatings. At cutting of steels the velocity of treatment was doubled, and also an oxygen flow was eliminated from the technological process and replaced by the air. The obtained raise of energy efficiency and quality of cutting is explained by an essential size reducing of a formed penetration channel and by the shifting of a thermal cutting mode from melting to evaporation. The evaluation of interaction efficiency of a combined radiation was produced on the basis of non-stationary thermal-hydrodynamic model of a heating source moving as in the cutting direction, and also into the depth of material.

Chapter 9: Metering Cross-Cutting Protocol. The Uniform Methods Project: Methods for Determining Energy-Efficiency Savings for Specific Measures

Energy Technology Data Exchange (ETDEWEB)

Mort, Dan [ADM Associates, Inc. Sacramento, CA (United States)

2017-09-01

Estimated energy savings are calculated as the difference between the energy use during the baseline period and the energy use during the post installation period of the EEM. This chapter describes the physical properties measured in the process of evaluating EEMs and the specific metering methods for several types of measurements. Skill-level requirements and other operating considerations are discussed, including where, when, and how often measurements should be made. The subsequent section identifies metering equipment types and their respective measurement accuracies. This is followed by sections containing suggestions regarding proper data handling procedures and the categorization and definition of several load types.

Model for Reggeon-Pomeranchukon cuts

International Nuclear Information System (INIS)

Chia, S.

1977-01-01

A model is presented for calculating Reggeon-Pomeranchukon cuts, making use explicitly of the Mandelstam diagram. External spins are treated in a natural way. Calculation for the general case is outlined and it is shown that in practical application the cut can be calculated in a standard way. Cuts associated with the exchanges of π, rho, B, and A 2 are considered, and characteristics of the RP cuts, as well as the structure functions, are extracted and discussed. It is found that the model differs considerably from the absorption model. Two suppression schemes are operative which control the magnitudes of cut contributions to amplitudes with ''naturality'' opposite to the Reggeon. The πP cut is found to be a unique case because of the smallness of the pion mass. In general, the RP cuts are self-conspiratorial. At very high energies, all cuts, except πP cut, exhibit quasifactorization

The cut-off point of dual energy X-ray and laser of calcaneus osteoporosis diagnosis in postmenopausal women

International Nuclear Information System (INIS)

Salimzadeh, A.; Forough, B.; Olia, B.; Alishiri, G. H.; Ghasemzadeh, A.

2005-01-01

Dual X-Ray Absorptiometry is a method which can extensively be used for bone mineral densitometry . Another more recent method is dual energy X-ray and laser, which associate with dual X ray absorptiometry, assisted by laser measure heel thickness. In this study the cut off points for dual energy X-ray and laser of calcaneus in the diagnosis of osteoporosis in different bone regions in postmenopausal women had been determined. Materials and Methods: In 268 postmenopausal women, BMD of the spinal and femoral regions was measured by DM, and the value for the calcaneous was measured by dual energy X-ray and laser. The agreement of the two methods in the diagnosis of osteoporosis and optimal cut-off point for dual energy X-ray and laser in defining osteoporosis was obtained. What obtained was the agreement of the two methods in the diagnosis of osteoporosis, as well as the optimal cut-off point for dual energy X-ray and laser in defining osteoporosis. Results: Dual X-Ray Absorptiometry showed osteoporosis in 40.7% of cases with 35.2% in L2-L4, 16.2% in the femoral neck, and 11.7% for the femoral total region. The dual energy X-ray and laser found osteoporosis, considering -2.5 SD as a threshold, in 26.1% of cases. Agreement of the two methods in the diagnosis of osteoporosis (Kappa score) was 0.443 for the lumbar region, 0.464 for the neck, and, 0.421 for total femur regions (all P values were significant). Using Receiver Operating Characteristic curves, it was found that a T-score of -2.1, -2.6 and -2.4 as the optimal cut-off point of dual energy X-ray and laser in the diagnosis of osteoporosis in the lumbar spine, the neck and total region of femur, respectively. Conclusion: The results of this study showed a moderate agreement between the two methods in the diagnosis of osteoporosis. It seems that the dual energy X-ray and laser cannot be used as a substitute for the DM method, but it can be used as a screening method to find (to diagnose) osteoporosis

Underwater cutting techniques developments

International Nuclear Information System (INIS)

Bach, F.-W.

1990-01-01

The primary circuit structures of different nuclear powerplants are constructed out of stainless steels, ferritic steels, plated ferritic steels and alloys of aluminium. According to the level of the specific radiation of these structures, it is necessary for dismantling to work with remote controlled cutting techniques. The most successful way to protect the working crew against exposure of radiation is to operate underwater in different depths. The following thermal cutting processes are more or less developed to work under water: For ferritic steels only - flame cutting; For ferritic steels, stainless steels, cladded steels and aluminium alloys - oxy-arc-cutting, arc-waterjet-cutting with a consumable electrode, arc-saw-cutting, plasma-arc-cutting and plasma-arc-saw. The flame cutting is a burning process, all the other processes are melt-cutting processes. This paper explains the different techniques, giving a short introduction of the theory, a discussion of the possibilities with the advantages and disadvantages of these processes giving a view into the further research work in this interesting field. (author)

Renewable energy and environmental technology: Norwegian trends, innovations and cutting-edge companies

Energy Technology Data Exchange (ETDEWEB)

Moses, Robert; Criscione, Valeria

2011-07-01

This issue of Norway Exports: Renewable Energy and environmental technology looks at Norway's role in one of most important global challenges today. Norway has long placed an emphasis on environmental issues both through global cooperation as well as initiatives on the national, regional and local level. In this issue we present you with two forewords; one from the Norwegian Minister of Petroleum and Energy, Ola Borten Moe, and one from Managing Director INTPOW, Geir Elsebutangen. A brief overview of the most important Norwegian environmental organizations as well as series of articles to give you a more in-depth understanding of Norway's present focus and activities. In the second half of the magazine you will find cutting-edge Norwegian companies within energy and renewable technology that provide their products or services on the global market.(Author)

High power laser downhole cutting tools and systems

Science.gov (United States)

Zediker, Mark S; Rinzler, Charles C; Faircloth, Brian O; Koblick, Yeshaya; Moxley, Joel F

2015-01-20

Downhole cutting systems, devices and methods for utilizing 10 kW or more laser energy transmitted deep into the earth with the suppression of associated nonlinear phenomena. Systems and devices for the laser cutting operations within a borehole in the earth. These systems and devices can deliver high power laser energy down a deep borehole, while maintaining the high power to perform cutting operations in such boreholes deep within the earth.

Cutting prepregs, cutting and processing polymer plastics in the manufacture of airсraft panels

OpenAIRE

MELUKHOV NIKITA; GRISHCHENKO TATIANA; LYUBUSHKIN VADIM

2017-01-01

The article presents an alternative to the solution of the problem of reduction of manual operations in manufacture. It may be achieved if cutting out prepregs and processing polymeric materials (PMP) be changed for sharp ultrasonic cutting when manufacturing components from polymeric composite materials (PCM). Described are the lines of investigations on new techniques of cutting out prepreg and processings polymeric material of the Nomex type with the use of the energy of ultrasonic waves. ...

On the Cutting Performance of Coated HSS Taps When Machining of Austenitic Steel

Science.gov (United States)

Sliwkova, Petra; Piska, Miroslav

2014-12-01

The paper deals with a quality of the PVD coated HSS taps when cutting the stainless austenitic chromiumnickel non-stabilized steel DIN 1.4301 (X5CrNi 18-10). The main attention is focused on the analysis of loading (cutting moment, specific energy) of the HSS taps by means of pieso-electrical dynamometer Kistler 9272 and the relation between the quality of duplex and triplex PVD coatings and their effects on the quality of machined thread surfaces and tool life of the taps. The results showed a safe and stabilized cutting with acceptable quality of threads for HSSE with the TiN+TiCN+DLC coating.

Energy efficiency, human behavior, and economic growth: Challenges to cutting energy demand to sustainable levels

Science.gov (United States)

Santarius, Tilman

2015-03-01

Increasing energy efficiency in households, transportation, industries, and services is an important strategy to reduce energy service demand to levels that allow the steep reduction of greenhouse gases, and a full fledged switch of energy systems to a renewable basis. Yet, technological efficiency improvements may generate so-called rebound effects, which may `eat up' parts of the technical savings potential. This article provides a comprehensive review of existing research on these effects, raises critiques, and points out open questions. It introduces micro-economic rebound effect and suggests extending consumer-side analysis to incorporate potential `psychological rebound effects.' It then discusses meso-economic rebound effects, i.e. producer-side and market-level rebounds, which so far have achieved little attention in the literature. Finally, the article critically reviews evidence for macro-economic rebound effects as energy efficiency-induced economic growth impacts. For all three categories, the article summarizes assessments of their potential quantitative scope, while pointing out remaining methodological weaknesses and open questions. As a rough "rule of thumb", in the long term and on gross average, only half the technical savings potential of across-the-board efficiency improvements may actually be achieved in the real world. Policies that aim at cutting energy service demand to sustainable levels are well advised to take due note of detrimental behavioral and economic growth impacts, and should foster policies and measures that can contain them.

Low specific-grinding energy machining of ceramics by a laser dressed diamond grinding stone

International Nuclear Information System (INIS)

Jodan, K.; Matsumaru, K.; Ishizaki, K.

2003-01-01

A laser dressing is an effective dressing method to accomplish efficient ceramic grinding. Since laser dressing achieves protrusion heights of abrasive-grains without grain dislodgment, the number of abrasive-grains in a laser dressed grinding stone (LGS) is higher than that in a mechanically dressed grinding stone (MGS), remaining the initial grain distribution. Thus, the LGS contains higher number of effective cutting edges, and forms higher number of ground grooves on a ground surface than the MGS. Consequently, the LGS can achieve lower specific grinding energy than the MGS. Copyright (2003) AD-TECH - International Foundation for the Advancement of Technology Ltd

Automated Laser Cutting In Three Dimensions

Science.gov (United States)

Bird, Lisa T.; Yvanovich, Mark A.; Angell, Terry R.; Bishop, Patricia J.; Dai, Weimin; Dobbs, Robert D.; He, Mingli; Minardi, Antonio; Shelton, Bret A.

1995-01-01

Computer-controlled machine-tool system uses laser beam assisted by directed flow of air to cut refractory materials into complex three-dimensional shapes. Velocity, position, and angle of cut varied. In original application, materials in question were thermally insulating thick blankets and tiles used on space shuttle. System shapes tile to concave or convex contours and cuts beveled edges on blanket, without cutting through outer layer of quartz fabric part of blanket. For safety, system entirely enclosed to prevent escape of laser energy. No dust generated during cutting operation - all material vaporized; larger solid chips dislodged from workpiece easily removed later.

Teaching about Climate Change and Energy with Online Materials and Workshops from On the Cutting Edge

Science.gov (United States)

Kirk, K. B.; Manduca, C. A.; Myers, J. D.; Loxsom, F.

2009-12-01

Global climate change and energy use are among the most relevant and pressing issues in today’s science curriculum, yet they are also complex topics to teach. The underlying science spans multiple disciplines and is quickly evolving. Moreover, a comprehensive treatment of climate change and energy use must also delve into perspectives not typically addressed in geosciences courses, such as public policy and economics. Thus, faculty attempting to address these timely issues face many challenges. To support faculty in teaching these subjects, the On the Cutting Edge faculty development program has created a series of websites and workshop opportunities to provide faculty with information and resources for teaching about climate and energy. A web-based collection of teaching materials was developed in conjunction with the On the Cutting Edge workshops “Teaching about Energy in Geoscience Courses: Current Research and Pedagogy.” The website is designed to provide faculty with examples, references and ideas for either incorporating energy topics into existing geoscience courses or for designing or refining a course about energy. The website contains a collection of over 30 classroom and lab activities contributed by faculty and covering such diverse topics as renewable energy, energy policy and energy conservation. Course descriptions and syllabi for energy courses address audiences ranging from introductory courses to advanced seminars. Other materials available on the website include a collection of visualizations and animations, a catalog of recommended books, presentations and related references from the teaching energy workshops, and ideas for novel approaches or new topics for teaching about energy in the geosciences. The Teaching Climate Change website hosts large collections of teaching materials spanning many different topics within climate change, climatology and meteorology. Classroom activities highlight diverse pedagogic approaches such as role

Cutting of nonmetallic materials using Nd:YAG laser beam

Institute of Scientific and Technical Information of China (English)

Bashir Ahmed Tahir; Rashid Ahmed; M. G. B. Ashiq; Afaq Ahmed; M. A. Saeed

2012-01-01

This study deals with Nd:YAG laser cutting nonmetallic materials,which is one of the most important and popular industrial applications of laser.The main theme is to evaluate the effects of Nd:YAG laser beam power besides work piece scanning speed.For approximate cutting depth,a theoretical study is conducted in terms of material property and cutting speed.Results show a nonlinear relation between the cutting depth and input energy.There is no significant effect of speed on cutting depth with the speed being larger than 30 mm/s.An extra energy is utilized in the deep cutting.It is inferred that as the laser power increases,cutting depth increases.The experimental outcomes are in good agreement with theoretical results.This analysis will provide a guideline for laser-based industry to select a suitable laser for cutting,scribing,trimming,engraving,and marking nonmetallic materials.

How much energy to process one pound of meat? A comparison of energy use and specific energy consumption in the meat industry of four European countries

International Nuclear Information System (INIS)

Ramirez, C.A.; Patel, M.; Blok, K.

2006-01-01

In this paper, we have used energy and physical production data to develop energy efficiency indicators for the meat industry of four European countries for the last 15 years. Our results show a significant increase in the energy use per tonne of product in all countries (between 14% and 48%). In order to understand the drivers behind the trends, factors such as the share of frozen products, the share of cut-up products and increasing food hygiene measures are analysed. We find that strong hygiene regulations can explain between one and two-thirds of the increase while the role of increasing shares of frozen and cut fresh meat it is found to be of no significance

Energy efficiency, human behavior, and economic growth: Challenges to cutting energy demand to sustainable levels

Energy Technology Data Exchange (ETDEWEB)

Santarius, Tilman, E-mail: tilman@santarius.de [Visiting Scholar, Institute of European Studies and Energy and Resources Group, University of California, Berkeley, 310 Barrows Hall, Berkeley, CA 94720-3050 (United States)

2015-03-30

Increasing energy efficiency in households, transportation, industries, and services is an important strategy to reduce energy service demand to levels that allow the steep reduction of greenhouse gases, and a full fledged switch of energy systems to a renewable basis. Yet, technological efficiency improvements may generate so-called rebound effects, which may ‘eat up’ parts of the technical savings potential. This article provides a comprehensive review of existing research on these effects, raises critiques, and points out open questions. It introduces micro-economic rebound effect and suggests extending consumer-side analysis to incorporate potential ‘psychological rebound effects.’ It then discusses meso-economic rebound effects, i.e. producer-side and market-level rebounds, which so far have achieved little attention in the literature. Finally, the article critically reviews evidence for macro-economic rebound effects as energy efficiency-induced economic growth impacts. For all three categories, the article summarizes assessments of their potential quantitative scope, while pointing out remaining methodological weaknesses and open questions. As a rough “rule of thumb”, in the long term and on gross average, only half the technical savings potential of across-the-board efficiency improvements may actually be achieved in the real world. Policies that aim at cutting energy service demand to sustainable levels are well advised to take due note of detrimental behavioral and economic growth impacts, and should foster policies and measures that can contain them.

MECHANISMS OF CUTTING BLADE WEAR AND THEIR INFLUENCE ON CUTTING ABILITY OF THE TOOL DURING MACHINING OF SPECIAL ALLOYS

Directory of Open Access Journals (Sweden)

Tomáš Zlámal

2016-09-01

Full Text Available With increased requirements for quality and shelf life of machined parts there is also a higher share of the use of material with specific properties that are identified by the term “superalloys”. These materials differ from common steels by mechanical and physical properties that cause their worse machinability. During machining of “superalloys” worse machinability has negative influence primarily on the amount of cutting edge wear, which shortens durability of the cutting tool. The goal of experimental activity shown in this contribution is to determine individual mechanisms of the cutting edge wear and their effects on the cutting ability during high speed machining of nickel superalloy. A specific exchangeable cutting insert made from cubic boric nitride was used for machining of the 625 material according to ASM 5666F. The criteria to evaluate cutting ability and durability of the cutting tool became selected parameters of surface integrity and quality of the machined surface.

Experimental study of the effect of gas nature on plasma arc cutting of mild steel

International Nuclear Information System (INIS)

Kavka, T; Mašláni, A; Hrabovský, M; Křenek, P; Stehrer, T; Pauser, H

2013-01-01

This paper is devoted to the experimental investigation of arc cutting of mild steel using plasmas generated in gas and liquid media. Due to different chemical compositions, the examined media have different thermophysical properties, which affect the properties of the generated plasma and cutting performance. The experiments are performed on 15 mm mild steel plates using commercial equipment at 60 A to approach real operation conditions in application areas. The studied gases are chosen according to recommendations of the world's leading manufacturers of arc cutting equipment for mild steel. Specific differences between plasma gases are discussed from the point of view of properties of the gas and the generated plasma, amount of removed material, kerf shape and overall energy balance of the cutting process. The paper describes the role of exothermic reaction of iron oxidation for oxygen cutting and explains its neglect for liquid cutting. This paper explains the potential of facilitating the cutting process by modification of the plasma gas chemical composition and flow rate. (paper)

Cutting of nonmetallic materials using Nd:YAG laser beam

International Nuclear Information System (INIS)

Tahir, Bashir Ahmed; Ashiq, M.G. B.; Saeed, M.A.; Ahmed, Rashid; Ahmed, Afaq

2012-01-01

This study deals with Nd:YAG laser cutting nonmetallic materials, which is one of the most important and popular industrial applications of laser. The main theme is to evaluate the effects of Nd:YAG laser beam power besides work piece scanning speed. For approximate cutting depth, a theoretical study is conducted in terms of material property and cutting speed. Results show a nonlinear relation between the cutting depth and input energy. There is no significant effect of speed on cutting depth with the speed being larger than 30 mm/s. An extra energy is utilized in the deep cutting. It is inferred that as the laser power increases, cutting depth increases. The experimental outcomes are in good agreement with theoretical results. This analysis will provide a guideline for laser-based industry to select a suitable laser for cutting, scribing, trimming, engraving, and marking nonmetallic materials. (electromagnetism, optics, acoustics, heat transfer, classical mechanics, and fluid dynamics)

Cuts in energy and operating cost with the Swiss system 'Energie in ARA' - practical experience in Germany; Energie- und Betriebskosteneinsparungen nach dem schweizerischen System ''Energie in ARA'' - Praxiserfahrungen in Deutschland

Energy Technology Data Exchange (ETDEWEB)

Christmann, B. [UmBAUwelt Partnerschaft Architekten und Ingenieure, Riedstadt (Germany)

1999-07-01

German sewage treatment plants, too, have potential for saving energy cost and cutting down on their operating expenditure. Following the systematy developed by the 'Energie in ARA' concept, this potential can be harnessed. (orig.) [German] Potential fuer Energiekosteneinsparungen und dadurch initiierte Betriebskosteneinsparungen ist auch bei deutschen Klaeranlagen vorhanden. Die Systematik 'Energie in ARA' kann fuer die Erschliessung der Einsparpotentiale verwendet werden. (orig.)

X-ray Spectral Survey of WGACAT Quasars, II: Optical and Radio Properties of Quasars with Low Energy X-ray Cut-offs

OpenAIRE

Elvis, Martin; Fiore, Fabrizio; Giommi, Paolo; Padovani, Paolo

1997-01-01

We have selected quasars with X-ray colors suggestive of a low energy cut-off, from the ROSAT PSPC pointed archive. We examine the radio and optical properties of these 13 quasars. Five out of the seven quasars with good optical spectra show associated optical absorption lines, with two having high delta-v candidate systems. Two other cut-off quasars show reddening associated with the quasar. We conclude that absorption is highly likely to be the cause of the X-ray cut-offs, and that the abso...

Cutting weeds with a CO2 laser

DEFF Research Database (Denmark)

Heisel, T.; Schou, Jørgen; Christensen, S.

2001-01-01

Stems of Chenopodium album. and Sinapis arvensis. and leaves of Lolium perenne. were cut with a CO2 laser or with a pair of scissors. Treatments were carried out on greenhouse-grown pot plants at three different growth stages and at two heights. Plant dry matter was measured 2 to 5 weeks after...... treatment. The relationship between dry weight and laser energy was analysed using a non-linear dose-response regression model. The regression parameters differed significantly between the weed species. At all growth stages and heights S. arvensis was more difficult to cut with a CO2 laser than C. album....... When stems were cut below the meristems, 0.9 and 2.3 J mm(-1) of CO2 laser energy dose was sufficient to reduce by 90% the biomass of C. album and S. arvensis respectively. Regrowth appeared when dicotyledonous plant stems were cut above meristems, indicating that it is important to cut close...

Disposal of oil cuttings by downhole fracturing injections : slurry product specifications issues

International Nuclear Information System (INIS)

Radzuan Junin

1994-01-01

The technique of using on-site injection of oil contaminated drill cuttings is attracting considerable attention as a cost effective means of complying with environmental legislation concerning discharges of drilling wastes. The slurrification and injection of oil based cuttings into a casing annulus, a process developed in 1989 by a major oil and gas producer/ operator, has proven to be a significant step toward reduction of such environmental waste. This paper discusses the development of the cuttings reinjection, slurrification, slurry properties and benefits of quality slurry, and behaviour of solid laden slurries in a fracture in conjunction with down-hole disposal operations

Energy substrate used by workers of leaf-cutting ants during nest excavation

Directory of Open Access Journals (Sweden)

Roberto S. Camargo

2013-12-01

Full Text Available Energy substrate used by workers of leaf-cutting ants during nest excavation. In this study we aimed to ascertain whether leaf-cutting ant workers lose body reserves (fat or sugars as a function of nest excavation. For each treatment, we isolated 10 workers of Atta sexdens into two experimental groups, Control (C- without excavation and Soil (S- with excavation, which were kept for different time intervals (0, 24, 48 or 72 hours, totaling 700 tested workers. We then determined the concentration of soluble carbohydrates and total lipid content in them. The total carbohydrates were determined colorimetrically, based on the reaction between carbohydrates and sulfuric acid-phenol. For determination of lipids, the insects were immersed in organic solvent until they reached a constant weight. Our results showed that carbohydrates are consumed during nest excavation activities. In the experimental groups S24, S48 and S72, there was an average reduction of 5.82 (20.42%, 14.31 (44.96% and 13.27 (43.96% µ.mg-1 in soluble sugar when compared with the experimental groups that did not excavate. Furthermore, the lipids were not used during this activity. With respect to dry mass of the workers, their values were C0 = 8%, C24 = 10.4%, C48 = 9.2%, C72 = 10%, S24 = 9.2%, S48 = 8.7% and S72 = 8.5%. Our results show experimentally that the source of energy for nest excavation is carbohydrates, whereas lipids are conserved for other activities.

Regge pole plus cut model for proton-antiproton elastic scattering at collider and tevatron energies

International Nuclear Information System (INIS)

Aleem, Fazal; Saleem, Mohammad

1988-01-01

The Regge pole plus cut model has been used to explain the data at the collider energies √=546 and 630 GeV and the most recent differential cross-section results at √=1.8 TeV. Predictions of the model at 1.8 and 40 TeV are compared with those of Bourrely et al. (1984). (author). 22 refs., 7 figs

Laser Cutting of Carbon Fiber Fabrics

Science.gov (United States)

Fuchs, A. N.; Schoeberl, M.; Tremmer, J.; Zaeh, M. F.

Due to their high weight-specific mechanical stiffness and strength, parts made from carbon fiber reinforced polymers (CFRP) are increasingly used as structural components in the aircraft and automotive industry. However, the cutting of preforms, as with most automated manufacturing processes for CFRP components, has not yet been fully optimized. This paper discusses laser cutting, an alternative method to the mechanical cutting of preforms. Experiments with remote laser cutting and gas assisted laser cutting were carried out in order to identify achievable machining speeds. The advantages of the two different processes as well as their fitness for use in mass production are discussed.

The cut-off values of dietary energy intake for determining metabolic syndrome in hemodialysis patients: A clinical cross-sectional study

Science.gov (United States)

Duong, Tuyen Van; Wong, Te-Chih; Chen, Hsi-Hsien; Chen, Tzen-Wen; Chen, Tso-Hsiao; Hsu, Yung-Ho; Peng, Sheng-Jeng; Kuo, Ko-Lin; Wang, Chi-Sin; Tseng, I-Hsin; Feng, Yi-Wei; Chang, Tai-Yue; Su, Chien-Tien

2018-01-01

Dietary energy intake strongly linked to dialysis outcomes. We aimed to explore the optimal cut-off point of energy intake (EI) for identification of metabolic syndrome (MetS) in hemodialysis patients. The cross-sectional data of 243 hemodialysis patients from multi-dialysis centers in Taiwan was used. The dietary intake was assessed by using the three-day dietary questionnaire, and a 24-hour dietary recall, clinical and biochemical data were also evaluated. The MetS was diagnosed by the Harmonized Metabolic Syndrome criteria. The receiver operating characteristic (ROC) curve was to depict the optimal cut-off value of EI for the diagnosis of MetS. The logistic regression was also used to explore the association between inadequate EI and MetS. The optimal cut-off points of EI for identifying the MetS were 26.7 kcal/kg/day for patients aged less than 60 years, or with non-diabetes, and 26.2 kcal/kg/day for patients aged 60 years and above, or with diabetes, respectively. The likelihood of the MetS increased with lower percentiles of energy intake in hemodialysis patients. In the multivariate analysis, the inadequate dietary energy intake strongly determined 3.24 folds of the MetS. The assessment of dietary EI can help healthcare providers detecting patients who are at risk of metabolic syndrome. PMID:29538427

One-dimensional cuts through multidimensional potential-energy surfaces by tunable x rays

Science.gov (United States)

Eckert, Sebastian; da Cruz, Vinícius Vaz; Gel'mukhanov, Faris; Ertan, Emelie; Ignatova, Nina; Polyutov, Sergey; Couto, Rafael C.; Fondell, Mattis; Dantz, Marcus; Kennedy, Brian; Schmitt, Thorsten; Pietzsch, Annette; Odelius, Michael; Föhlisch, Alexander

2018-05-01

The concept of the potential-energy surface (PES) and directional reaction coordinates is the backbone of our description of chemical reaction mechanisms. Although the eigenenergies of the nuclear Hamiltonian uniquely link a PES to its spectrum, this information is in general experimentally inaccessible in large polyatomic systems. This is due to (near) degenerate rovibrational levels across the parameter space of all degrees of freedom, which effectively forms a pseudospectrum given by the centers of gravity of groups of close-lying vibrational levels. We show here that resonant inelastic x-ray scattering (RIXS) constitutes an ideal probe for revealing one-dimensional cuts through the ground-state PES of molecular systems, even far away from the equilibrium geometry, where the independent-mode picture is broken. We strictly link the center of gravity of close-lying vibrational peaks in RIXS to a pseudospectrum which is shown to coincide with the eigenvalues of an effective one-dimensional Hamiltonian along the propagation coordinate of the core-excited wave packet. This concept, combined with directional and site selectivity of the core-excited states, allows us to experimentally extract cuts through the ground-state PES along three complementary directions for the showcase H2O molecule.

Laser cutting of Kevlar laminates

Energy Technology Data Exchange (ETDEWEB)

VanCleave, R.A.

1977-09-01

An investigation has been conducted of the use of laser energy for cutting contours, diameters, and holes in flat and shaped Kevlar 49 fiber-reinforced epoxy laminates as an alternate to conventional machining. The investigation has shown that flat laminates 6.35 mm thick may be cut without backup by using a high-powered (1000-watt) continuous wave CO/sub 2/ laser at high feedrates (33.87 mm per second). The cut produced was free of the burrs and delaminations resulting from conventional machining methods without intimate contact backup. In addition, the process cycle time was greatly reduced.

In the suppression of regge cut contributions

International Nuclear Information System (INIS)

Chia, S.P.

1975-07-01

It is shown that contributions of reggeon-pomeron cuts are suppressed in amplitudes with opposite natural to the reggeon. This suppression grows logarithmically with energy. The suppression in the πP cut is, however, found to be weak. Consequence on conspiracy is discussed

Determination of cosmic ray (CR) ionization path and iono/atmospheric cut-off energy from CR intervals III, IV and V in the planetary environments

International Nuclear Information System (INIS)

Velinov, P.

2001-01-01

In this paper are determined the ionization path and cut-off energies of the cosmic ray (CR) nuclei in relation to the general interaction model 'CR - ionosphere-middle atmosphere'. Here the ionization path and the iono/atmospheric cut-off energies of the galactic CR, solar CR and anomalous CR are separately considered in each energetic range, without taking into account the particle transfer from one range in another. This more general approach will be the object of a further paper

Robotics Technology Development Program Cross Cutting and Advanced Technology

International Nuclear Information System (INIS)

Harrigan, R.W.; Horschel, D.S.

1994-01-01

Need-based cross cutting technology is being developed which is broadly applicable to the clean up of hazardous and radioactive waste within the US Department of Energy's complex. Highly modular, reusable technologies which plug into integrated system architectures to meet specific robotic needs result from this research. In addition, advanced technologies which significantly extend current capabilities such as automated planning and sensor-based control in unstructured environments for remote system operation are also being developed and rapidly integrated into operating systems

Near-Infrared Quantum Cutting Long Persistent Luminescence

OpenAIRE

Zou, Zehua; Feng, Lin; Cao, Cheng; Zhang, Jiachi; Wang, Yuhua

2016-01-01

By combining the unique features of the quantum cutting luminescence and long persistent luminescence, we design a new concept called ?near-infrared quantum cutting long persistent luminescence (NQPL)?, which makes it possible for us to obtain highly efficient (>100%) near-infrared long persistent luminescence in theory. Guided by the NQPL concept, we fabricate the first NQPL phosphor Ca2Ga2GeO7:Pr3+,Yb3+. It reveals that both the two-step energy transfer of model (I) and the one-step energy ...

Surface modification of multi-point cutting tools using ion implantation

International Nuclear Information System (INIS)

Sarwar, M.; Ahmed, W.; Ahmed, M.

1995-01-01

Ion-implantation has been used to treat multi-point cutting tools using a 'systems approach' in order to improve the performance of these tools in dynamic cutting conditions. The effects of energy, species and system pressure on life and performance of circular saws have been investigated. For both nitrogen and argon ion-implantation an improvement in cutting performance has been observed as compared to untreated edges. As the energy of the nitrogen ions is increased there is a gradual improvement in the performance of the cutting edge. Ion-implanted tools were compared to those coated with TiN and these results are also presented. (author) 5 figs

Deferment cutting in Appalachian hardwoods: the what, whys, and hows

Science.gov (United States)

H. Clay Smith; Gary W. Miller

1991-01-01

Deferment cutting is a regeneration practice that resembles a seed-tree or shelterwood cutting. The difference is that residual trees are not cut when the reproduction becomes established. Instead, residual trees are left until new reproduction matures to sawtimber size, and another regeneration cut is the silvicultural objective. Hence, with deferment cutting specific...

29 CFR 1926.351 - Arc welding and cutting.

Science.gov (United States)

2010-07-01

... 29 Labor 8 2010-07-01 2010-07-01 false Arc welding and cutting. 1926.351 Section 1926.351 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Welding and Cutting § 1926.351 Arc welding and cutting. (a) Manual electrode holders. (1) Only manual electrode holders which are specifically designed...

All orders transport theory from the multiple scattering expansion of the self-energy. The central cuts

International Nuclear Information System (INIS)

Gagnon, J.S.; Fillion-Gourdeau, F.; Sangyong Jeong; RIKEN Research Center, Upton, NY

2006-01-01

We use the full multiple scattering expansion of the retarded self-energy to obtain the gain and loss rates present in the Kadanoff-Baym relativistic transport equation. The rates we obtain include processes with any number of particles. As a first approximation, we only consider central cuts in the self-energies, but otherwise our results are general. We specialize to the case of scalar field theory to compare with lowest order results. The main application of this work is relativistic transport theory of very dense systems, such as the quark-gluon plasma or the early universe, where multi-particle interactions are important. (author)

Loop equations for multi-cut matrix models

International Nuclear Information System (INIS)

Akemann, G.

1995-03-01

The loop equation for the complex one-matrix model with a multi-cut structure is derived and solved in the planar limit. An iterative scheme for higher genus contributions to the free energy and the multi-loop correlators is presented for the two-cut model, where explicit results are given up to and including genus two. The double-scaling limit is analyzed and the relation to the one-cut solution of the hermitian and complex one-matrix model is discussed. (orig.)

Development of laser cutting method for stainless steel liner

International Nuclear Information System (INIS)

Ishihara, Satoshi; Takahata, Masato; Wignarajah, Sivakumaran; Kamata, Hirofumi

2007-01-01

The present work is an attempt to develop a laser cutting method for cutting and removing stainless steel liners from concrete walls and floors in nuclear facilities. The effect of basic laser cutting parameters such as energy, cutting speed, assist gas flow etc. were first studied through cutting experiments on mock-up concrete specimens lined with 3mm thick stainless steel sheets using a 1kW Nd:YAG laser. These initial studies were followed by further studies on the effect of unevenness of the liner surface and on a new method of confining contamination during the cutting process using a sliding evacuation hood attached to the laser cutting head. The results showed that laser cutting is superior to other conventional cutting methods from the point of view of safety from radioactivity and work efficiency when cutting contaminated stainless steel liners. (author)

Aerodynamic Interactions During Laser Cutting

Science.gov (United States)

Fieret, J.; Terry, M. J.; Ward, B. A.

1986-11-01

Most laser cutting systems utilise a gas jet to remove molten or vaporised material from the kerf. The speed, economy and quality of the cut can be strongly dependent on the aerodynamic conditions created by the nozzle, workpiece proximity and kerf shape. Adverse conditions can be established that may lead to an unwelcome lack of reproducibility of cut quality. Relatively low gas nozzle pressures can result in supersonic flow in the jet with its associated shock fronts. When the nozzle is placed at conventional distances (1-2mm) above the workpiece, the force exerted by the gas on the workpiece and the cut products (the cutting pressure) can be significantly less than the nozzle pressure. Higher cutting pressures can be achieved by increasing the height of the nozzle above the workpiece, to a more damage resistant zone, provided that the shock structure of the jet is taken into account. Conventional conical nozzles with circular exits can be operated with conditions that will result in cutting pressures up to 3 Bar (g) in the more distant zone. At higher pressures in circular tipped nozzles the cutting pressure in this zone decays to inadequate levels. Investigations of a large number of non-circular nozzle tip shapes have resulted in the selection of a few specific shapes that can provide cutting pressures in excess of 6 Bar(g) at distances of 4 to 7mm from the nozzle tip. Since there is a strong correlation between cutting pressure and the speed and quality of laser cutting, the paper describes the aerodynamic requirements for achieving the above effects and reports the cutting results arising from the different nozzle designs and conditions. The results of the work of other investigators, who report anomalous laser cutting results, will be examined and reviewed in the light of the above work.

An innovative apparatus provided with a cutting auger for producing short logs for biomass energy from fast-growing tree species

Energy Technology Data Exchange (ETDEWEB)

Colorio, G.; Tomasone, R.; Cedrola, C.; Pagano, M.; Pochi, D.; Fanigliulo, R.; Sperandio, G. [Council for Research in Agriculture, Agricultural Engineering Research Unit, Rome (Italy)

2010-07-01

This paper reported on a new cutting mechanism that cuts fresh wood into small pieces instead of wood chips in order to avoid the problem of fermentation that occurs in storage. The prototype cutting device performs a gradual and oblique cut. It consists of a large auger in which a knife is inserted on the outer edge of the helicoid. Tree trunks up to 20 cm in diameter are fed perpendicularly into the machine and are pushed along the axis where slices are cut off against a fixed sharp-edged counter blade. The cylinder enclosing the auger is the main frame of the machine, and is closed at one end, where a heavy flywheel delivers the energy coming from the tractor's power take-off (PTO). The wood pieces ranging in length from 4 to 19 cm exit through the opposite end. The auger is 700 mm in diameter with a 300 mm pitch spacing. The logs are pushed into the machine by counter-rotating rollers placed in the feed funnel. Tests were conducted to determine the operative performance and power requirements of the machine. The cutting method requires less power compared to wood chipping machines. Work capacity is greater when producing slices instead of chips and the system produces less noise and fewer vibrations. The auger reaches a constant velocity of 200 RPM and can easily cut fresh wood of different species.

High speed laser cutting machine. Kosoku reza kakoki

Energy Technology Data Exchange (ETDEWEB)

Shinno, N. (Matsushita Electric Industrial Co. Ltd., Kadoma, Osaka (Japan))

1993-11-01

The carbon dioxide gas laser cutting machine is being used widely for from cutting soft steel and stainless steel, etc. to intermetallic welding and in the field of cutting in particular, concerning sheet cutting, it has been changing the existing monopoly of the turret punch press, and as for medium and thick plate cutting, that of the gas plasma fusing device. This article is the general description of high speed laser cutting machine. Concerning the laser cutting (sheet cutting in particular), as the essential items for securing severe cutting accuracy and, at the same time, improving the cutting speed, the following matters are picked up for respective explanation; improvement of stationary machine accuracy, improvement of dynamic machine accuracy, improvement of quality of laser beam as well as optimization of cutting conditions, and shortening of piercing time. Also explanation is given to the respective items, namely speeding-up of medium and thick plate cutting, and reduction of load onto the operator by improved operation. Finally, feeding and removing of a sheet only, and feeding and removing with a pallet are mentioned as the efforts for automation and energy saving. 3 figs., 1 tab.

Visualization of the dissipation of energy during the cutting process. Presentation of energy value flows by means of dual energy signatures; Energieverschwendung beim Zerspanungsprozess sichtbar machen. Darstellung von Energiewertstroemen mittels dualer Energiesignaturen

Energy Technology Data Exchange (ETDEWEB)

Schillig, Rainer [Hochschule Aalen (Germany). Professur Fertigungsorganisation und Prozessmanagement; Kalhoefer, Eckehard [Hochschule Aalen (Germany). Stiftungslehrstuhl Spanende Fertigung; Stock, Timo [Hochschule Aalen (Germany). Studiengang Maschinenbau/Produktion und Management

2012-09-15

Lean production systems are the minimization of wastage. Therefore, process steps are divided in value-added and non-value-added process steps. Using the value stream analysis non-value-adding process shares can be identified easily.The main aim usually are the two factors processing time and inventory. By means of a cutting process, the authors of the paper under consideration report on a method which divides the process-related utilization of energy in value-adding and non-value-adding energy use. Due to the dual consideration of energy use, the energy consumption can be easily integrated in the value stream analysis.

Cut elimination in multifocused linear logic

DEFF Research Database (Denmark)

Guenot, Nicolas; Brock-Nannestad, Taus

2015-01-01

We study cut elimination for a multifocused variant of full linear logic in the sequent calculus. The multifocused normal form of proofs yields problems that do not appear in a standard focused system, related to the constraints in grouping rule instances in focusing phases. We show that cut...... elimination can be performed in a sensible way even though the proof requires some specific lemmas to deal with multifocusing phases, and discuss the difficulties arising with cut elimination when considering normal forms of proofs in linear logic....

Plasma arc cutting: speed and cut quality

International Nuclear Information System (INIS)

Nemchinsky, V A; Severance, W S

2009-01-01

When cutting metal with plasma arc cutting, the walls of the cut are narrower at the bottom than at the top. This lack of squareness increases as the cutting speed increases. A model of this phenomenon, affecting cut quality, is suggested. A thin liquid layer, which separates the plasma from the solid metal to be melted, plays a key role in the suggested model. This layer decreases heat transfer from the plasma to the solid metal; the decrease is more pronounced the higher the speed and the thicker the liquid metal layer. Since the layer is thicker at the bottom of the cut, the heat transfer effectiveness is lower at the bottom. The decrease in heat transfer effectiveness is compensated by the narrowness of the cut. The suggested model allows one to calculate the profile of the cut. The result of the calculations of the cutting speeds for plates of various thicknesses, at which the squareness of the cut is acceptable, agrees well with the speeds recommended by manufacturers. The second effect considered in the paper is the deflection of the plasma jet from the vertical at a high cutting speed. A qualitative explanation of this phenomenon is given. We believe the considerations of this paper are pertinent to other types of cutting with moving heat sources.

Cutting

Science.gov (United States)

... Staying Safe Videos for Educators Search English Español Cutting KidsHealth / For Teens / Cutting What's in this article? ... Getting Help Print en español Cortarse What Is Cutting? Emma's mom first noticed the cuts when Emma ...

Study on processing parameters of glass cutting by nanosecond 532 nm fiber laser

Science.gov (United States)

Wang, Jin; Gao, Fan; Xiong, Baoxing; Zhang, Xiang; Yuan, Xiao

2018-03-01

The processing parameters of soda-lime glass cutting with several nanosecond 532 nm pulsed fiber laser are studied in order to obtain sufficiently large ablation rate and better processing quality. The influences of laser processing parameters on effective cutting speed and cutting quality of 1 2 mm thick soda-lime glass are studied. The experimental results show that larger laser pulse energy will lead to higher effective cutting speed and larger maximum edge collapse of the front side of the glass samples. Compared with that of 1.1 mm thick glass samples, the 2.0 mm thick glass samples is more difficult to cut. With the pulse energy of 51.2 μJ, the maximum edge collapse is more than 200 μm for the 2.0 mm thick glass samples. In order to achieve the high effective cutting speed and good cutting quality at the same time, the dual energy overlapping method is used to obtain the better cutting performance for the 2.0 mm thick glass samples, and the cutting speed of 194 mm/s and the maximum edge collapse of less than 132 μm are realized.

Spread of `Eco-vendor`, an energy-saving type automatic vending machine for beverages with a peak cut function; Shoenegata seiryo inryoyo jido hanbaiki (peak cut kino tsuki) `eko benda` no fukyu ni tsuite

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-05-01

`Eco-vendor`, an energy-saving type automatic vending machine for beverages with a peak cut function has been developed in 1995 through cooperation by Tokyo Electric Power Company, Coca-Cola Japan, and Fuji Electric Co., Ltd. It can cut 90 percent of the power consumption during 13:00 to 16:00 on weekdays in summer, and can save 10 to 15 percent of annual power consumption. Since the heat insulation performance has been improved to keep beverages at the set temperature during the peak cut operation, the energy-saving effect for cold products in summer and for hot products in winter has been enhanced. For the manufacturing of `Eco-vendor`, Fuji Electric Co., Ltd. has offered its technical know-how to five manufacturers of automatic vending machine for beverages without compensation, and each manufacturer has accepted the offer. Electric power companies of Japan have cooperated to pay incident of 10,000 yen per an `Eco-vendor` to the manufacturers. Japan`s automatic vending machine industries and nationwide beverage industries have positively cooperated. Consequently, Tokyo Electric Power Company has successfully spread 2,600 machines up to the end of fiscal 1995, and aims at the spread of 16,000 machines in fiscal 1996. 2 figs.

An evaluation of alternative reactor vessel cutting technologies for the experimental boiling water reactor at Argonne National Laboratory

International Nuclear Information System (INIS)

Boing, L.E.; Henley, D.R.; Manion, W.J.; Gordon, J.W.

1989-12-01

Metal cutting techniques that can be used to segment the reactor pressure vessel of the Experimental Boiling Water Reactor (EBWR) at Argonne National Laboratory (ANL) have been evaluated by Nuclear Energy Services. Twelve cutting technologies are described in terms of their ability to perform the required task, their performance characteristics, environmental and radiological impacts, and cost and schedule considerations. Specific recommendations regarding which technology should ultimately be used by ANL are included. The selection of a cutting method was the responsibility of the decommissioning staff at ANL, who included a relative weighting of the parameters described in this document in their evaluation process. 73 refs., 26 figs., 69 tabs

An evaluation of alternative reactor vessel cutting technologies for the experimental boiling water reactor at Argonne National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Boing, L.E.; Henley, D.R. (Argonne National Lab., IL (USA)); Manion, W.J.; Gordon, J.W. (Nuclear Energy Services, Inc., Danbury, CT (USA))

1989-12-01

Metal cutting techniques that can be used to segment the reactor pressure vessel of the Experimental Boiling Water Reactor (EBWR) at Argonne National Laboratory (ANL) have been evaluated by Nuclear Energy Services. Twelve cutting technologies are described in terms of their ability to perform the required task, their performance characteristics, environmental and radiological impacts, and cost and schedule considerations. Specific recommendations regarding which technology should ultimately be used by ANL are included. The selection of a cutting method was the responsibility of the decommissioning staff at ANL, who included a relative weighting of the parameters described in this document in their evaluation process. 73 refs., 26 figs., 69 tabs.

Graph-cut based discrete-valued image reconstruction.

Science.gov (United States)

Tuysuzoglu, Ahmet; Karl, W Clem; Stojanovic, Ivana; Castañòn, David; Ünlü, M Selim

2015-05-01

Efficient graph-cut methods have been used with great success for labeling and denoising problems occurring in computer vision. Unfortunately, the presence of linear image mappings has prevented the use of these techniques in most discrete-amplitude image reconstruction problems. In this paper, we develop a graph-cut based framework for the direct solution of discrete amplitude linear image reconstruction problems cast as regularized energy function minimizations. We first analyze the structure of discrete linear inverse problem cost functions to show that the obstacle to the application of graph-cut methods to their solution is the variable mixing caused by the presence of the linear sensing operator. We then propose to use a surrogate energy functional that overcomes the challenges imposed by the sensing operator yet can be utilized efficiently in existing graph-cut frameworks. We use this surrogate energy functional to devise a monotonic iterative algorithm for the solution of discrete valued inverse problems. We first provide experiments using local convolutional operators and show the robustness of the proposed technique to noise and stability to changes in regularization parameter. Then we focus on nonlocal, tomographic examples where we consider limited-angle data problems. We compare our technique with state-of-the-art discrete and continuous image reconstruction techniques. Experiments show that the proposed method outperforms state-of-the-art techniques in challenging scenarios involving discrete valued unknowns.

Experimental comparison of laser energy losses in high-quality laser-oxygen cutting of low-carbon steel using radiation from fibre and CO2 lasers

International Nuclear Information System (INIS)

Golyshev, A A; Malikov, A G; Orishich, A M; Shulyat'ev, V B

2015-01-01

We report a comparative experimental study of laseroxygen cutting of low-carbon steel using a fibre laser with a wavelength of 1.07 μm and a CO 2 laser with a wavelength of 10.6 μm at the sheet thickness of 3 – 16 mm. For the two lasers we have measured the dependence of the cutting speed on the radiation power and determined the cutting speed at which the surface roughness is minimal. The coefficient of laser radiation absorption in the laser cutting process is measured for these lasers at different values of the cutting speed and radiation power. It is found that the minimal roughness of the cut surface is reached at the absorbed laser energy per unit volume of the removed material, equal to 11 – 13 J mm -3 ; this value is the same for the two lasers and does not depend on the sheet thickness. (laser technologies)

Influence of minimum quantity lubrication with Al2O3 nanoparticles on cutting parameters in drilling process

Science.gov (United States)

Fitrina, Sofia; Kristiawan, Budi; Surojo, Eko; Wijayanta, Agung Tri; Miyazaki, Takahiko; Koyama, Shigeru

2018-02-01

Machining is one of the largest and most widely used methods of production segments in industries. In this way, cutting fluids play an important role in minimizing production time, cost, and energy in various machining operations. This paper presents an experimental investigation into minimum quantity lubrication (MQL) with Al2O3 nanoparticles in drilling process of common rail as work material with DPSCM 435H code to analyze its influence on cutting parameters. Al2O3 has been selected for nanoparticles in this study due to its non-toxicity and spherical shapes for enhanced tribological attributes. Experiments were carried out for two different conditions; MQL + nanofluids (250 ml/h) and conventional cutting fluid (15 liters/min). In this work, nanofluid was prepared by adding Al2O3 nanoparticles (13 nm size) into the conventional cutting fluid in the specific proportion of 1.2 vol.%. The experiment results reveal that the performance of Al2O3 nanofluid in term surface roughness is better compared to the conventional cutting fluid, but the result of cutting temperature and chip morphology does not match with the previous experiment because volume fraction of nanofluid is too high. It means the specific proportion of 1.2 vol.% nanofluid is not best volume fraction for getting best cooling properties. This experiment does not focus on variations of volume fraction but on cooling conditions.

Determination of cut front position in laser cutting

Science.gov (United States)

Pereira, M.; Thombansen, U.

2016-07-01

Laser cutting has a huge importance to manufacturing industry. Laser cutting machines operate with fixed technological parameters and this does not guarantee the best productivity. The adjustment of the cutting parameters during operation can improve the machine performance. Based on a coaxial measuring device it is possible to identify the cut front position during the cutting process. This paper describes the data analysis approach used to determine the cut front position for different feed rates. The cut front position was determined with good resolution, but improvements are needed to make the whole process more stable.

Experimental testing of exchangeable cutting inserts cutting ability

OpenAIRE

Čep, Robert; Janásek, Adam; Čepová, Lenka; Petrů, Jana; Hlavatý, Ivo; Car, Zlatan; Hatala, Michal

2013-01-01

The article deals with experimental testing of the cutting ability of exchangeable cutting inserts. Eleven types of exchangeable cutting inserts from five different manufacturers were tested. The tested cutting inserts were of the same shape and were different especially in material and coating types. The main aim was both to select a suitable test for determination of the cutting ability of exchangeable cutting inserts and to design such testing procedure that could make it possible...

Determination of cut front position in laser cutting

International Nuclear Information System (INIS)

Pereira, M; Thombansen, U

2016-01-01

Laser cutting has a huge importance to manufacturing industry. Laser cutting machines operate with fixed technological parameters and this does not guarantee the best productivity. The adjustment of the cutting parameters during operation can improve the machine performance. Based on a coaxial measuring device it is possible to identify the cut front position during the cutting process. This paper describes the data analysis approach used to determine the cut front position for different feed rates. The cut front position was determined with good resolution, but improvements are needed to make the whole process more stable. (paper)

Quantum Max-flow/Min-cut

Science.gov (United States)

Cui, Shawn X.; Freedman, Michael H.; Sattath, Or; Stong, Richard; Minton, Greg

2016-06-01

The classical max-flow min-cut theorem describes transport through certain idealized classical networks. We consider the quantum analog for tensor networks. By associating an integral capacity to each edge and a tensor to each vertex in a flow network, we can also interpret it as a tensor network and, more specifically, as a linear map from the input space to the output space. The quantum max-flow is defined to be the maximal rank of this linear map over all choices of tensors. The quantum min-cut is defined to be the minimum product of the capacities of edges over all cuts of the tensor network. We show that unlike the classical case, the quantum max-flow=min-cut conjecture is not true in general. Under certain conditions, e.g., when the capacity on each edge is some power of a fixed integer, the quantum max-flow is proved to equal the quantum min-cut. However, concrete examples are also provided where the equality does not hold. We also found connections of quantum max-flow/min-cut with entropy of entanglement and the quantum satisfiability problem. We speculate that the phenomena revealed may be of interest both in spin systems in condensed matter and in quantum gravity.

Quantum Max-flow/Min-cut

Energy Technology Data Exchange (ETDEWEB)

Cui, Shawn X., E-mail: xingshan@math.ucsb.edu [Department of Mathematics, University of California, Santa Barbara, California 93106 (United States); Quantum Architectures and Computation Group, Microsoft Research, Redmond, Washington 98052 (United States); Freedman, Michael H., E-mail: michaelf@microsoft.com [Department of Mathematics, University of California, Santa Barbara, California 93106 (United States); Microsoft Research, Station Q, University of California, Santa Barbara, California 93106 (United States); Sattath, Or, E-mail: sattath@gmail.com [Computer Science Division, University of California, Berkeley, California 94720 (United States); Stong, Richard, E-mail: stong@ccrwest.org; Minton, Greg, E-mail: gtminto@ccrwest.org [Center for Communications Research, La Jolla, California 92121 (United States)

2016-06-15

The classical max-flow min-cut theorem describes transport through certain idealized classical networks. We consider the quantum analog for tensor networks. By associating an integral capacity to each edge and a tensor to each vertex in a flow network, we can also interpret it as a tensor network and, more specifically, as a linear map from the input space to the output space. The quantum max-flow is defined to be the maximal rank of this linear map over all choices of tensors. The quantum min-cut is defined to be the minimum product of the capacities of edges over all cuts of the tensor network. We show that unlike the classical case, the quantum max-flow=min-cut conjecture is not true in general. Under certain conditions, e.g., when the capacity on each edge is some power of a fixed integer, the quantum max-flow is proved to equal the quantum min-cut. However, concrete examples are also provided where the equality does not hold. We also found connections of quantum max-flow/min-cut with entropy of entanglement and the quantum satisfiability problem. We speculate that the phenomena revealed may be of interest both in spin systems in condensed matter and in quantum gravity.

Chapter 12: Survey Design and Implementation for Estimating Gross Savings Cross-Cutting Protocol. The Uniform Methods Project: Methods for Determining Energy Efficiency Savings for Specific Measures

Energy Technology Data Exchange (ETDEWEB)

Kurnik, Charles W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Baumgartner, Robert [Tetra Tech, Madison, WI (United States)

2017-10-05

This chapter presents an overview of best practices for designing and executing survey research to estimate gross energy savings in energy efficiency evaluations. A detailed description of the specific techniques and strategies for designing questions, implementing a survey, and analyzing and reporting the survey procedures and results is beyond the scope of this chapter. So for each topic covered below, readers are encouraged to consult articles and books cited in References, as well as other sources that cover the specific topics in greater depth. This chapter focuses on the use of survey methods to collect data for estimating gross savings from energy efficiency programs.

Efficiency of laser beam utilization in gas laser cutting of materials

Science.gov (United States)

Galushkin, M. G.; Grishaev, R. V.

2018-02-01

Relying on the condition of dynamic matching of the process parameters in gas laser cutting, the dependence of the beam utilization factor on the cutting speed and the beam power has been determined. An energy balance equation has been derived for a wide range of cutting speed values.

Experimental comparison of laser energy losses in high-quality laser-oxygen cutting of low-carbon steel using radiation from fibre and CO{sub 2} lasers

Energy Technology Data Exchange (ETDEWEB)

Golyshev, A A; Malikov, A G; Orishich, A M; Shulyat' ev, V B [S.A. Khristianovich Institute of Theoretical and Applied Mechanics, Siberian Branch, Russian Academy of Sciences, Novosibirsk (Russian Federation)

2015-09-30

We report a comparative experimental study of laseroxygen cutting of low-carbon steel using a fibre laser with a wavelength of 1.07 μm and a CO{sub 2} laser with a wavelength of 10.6 μm at the sheet thickness of 3 – 16 mm. For the two lasers we have measured the dependence of the cutting speed on the radiation power and determined the cutting speed at which the surface roughness is minimal. The coefficient of laser radiation absorption in the laser cutting process is measured for these lasers at different values of the cutting speed and radiation power. It is found that the minimal roughness of the cut surface is reached at the absorbed laser energy per unit volume of the removed material, equal to 11 – 13 J mm{sup -3}; this value is the same for the two lasers and does not depend on the sheet thickness. (laser technologies)

Core Cutting Test with Vertical Rock Cutting Rig (VRCR)

Science.gov (United States)

Yasar, Serdar; Osman Yilmaz, Ali

2017-12-01

Roadheaders are frequently used machines in mining and tunnelling, and performance prediction of roadheaders is important for project economics and stability. Several methods were proposed so far for this purpose and, rock cutting tests are the best choice. Rock cutting tests are generally divided into two groups which are namely, full scale rock cutting tests and small scale rock cutting tests. These two tests have some superiorities and deficiencies over themselves. However, in many cases, where rock sampling becomes problematic, small scale rock cutting test (core cutting test) is preferred for performance prediction, since small block samples and core samples can be conducted to rock cutting testing. Common problem for rock cutting tests are that they can be found in very limited research centres. In this study, a new mobile rock cutting testing equipment, vertical rock cutting rig (VRCR) was introduced. Standard testing procedure was conducted on seven rock samples which were the part of a former study on cutting rocks with another small scale rock cutting test. Results showed that core cutting test can be realized successfully with VRCR with the validation of paired samples t-test.

Force Relations and Dynamics of Cutting Knife in a Vertical Disc Mobile Wood Chipper

Directory of Open Access Journals (Sweden)

Segun R. BELLO

2011-06-01

Full Text Available The force relations and dynamics of cutting knife in a vertical disc wood chipper were investigated. The tool geometry determined include: rake angle (20 deg C; Shear angle, (fi= 52.15 deg C; the mean frictional angle, (t = 5.71 deg C. The analysis and comparison of the cutting forces has shown that the chips separated from the wood are being formed by off cutting, since normal applied force N is compressive in nature, the magnitude of the forces used by the knife on the wood is expected to increase as the cutting edge of the knife goes deeper into the wood until the value of the resisting force acting against the cut wood Ff is reached and exceeded. The evaluated forces acting on the knife and the chip are: F = 3.63Nmm^-1; N = 34.7 Nmm^-1; Fs= 27.45Nmm^-1; Fn =31.92 Nmm^-1; Ft = -8.46Nmm^-1; Fc = 33.85Nmm^-1. The resultant force acting on the tool face, Pr = 34.89Nmm^-1. The specific cutting pressure, Pc and cutting force needed to cut the timber, Fc, are 1.79 × 10^6 N/m2 and 644.84N respectively. The energy consumed in removing a unit volume of material is 69.96kJ/mm^-3 and the maximum power developed in cutting the chip is 3591.77W (4.82hp. The chipper efficiency (86.6% was evaluated by the highest percentage of accepted chip sizes.

Energy Requirements for Biomass Harvest and Densification

Directory of Open Access Journals (Sweden)

Kevin Shinners

2018-03-01

Full Text Available This research quantified the unit and bulk density of several biomass crops across a variety of harvest and processing methods, as well as the energy and fuel requirements for these operations. A load density of approximately 240 kg·m−3 is needed to reach the legal weight limit of most transporters. Of the three types of balers studied, only the high density (HD large square baler achieved this target density. However, the specific energy and fuel requirements increased exponentially with bale density, and at the maximum densities for corn stover and switchgrass, the dry basis energy and fuel requirements ranged from 4.0 to 5.0 kW·h·Mg−1 and 1.2 to 1.4 L·Mg−1, respectively. Throughputs of tub grinders when grinding bales was less than any other harvesting or processing methods investigated, so specific energy and fuel requirements were high and ranged from 13 to 32 kW·h·Mg−1 and 5.0 to 11.3 L·Mg−1, respectively. Gross size-reduction by pre-cutting at baling increased bale density by less than 6% and increased baling energy requirements by 11% to 22%, but pre-cut bales increased the tub grinder throughput by 25% to 45% and reduced specific fuel consumption for grinding by 20% to 53%. Given the improvement in tub grinder operation, pre-cutting bales should be considered as a means to increase grinder throughput. Additional research is needed to determine the energy required to grind high density pre-cut bales at high throughputs so that better estimates of total energy required for a high density bale system can be made. An alternative bulk feedstock system was investigated that involved chopping moist biomass crops with a precision-cut forage harvester, compacting the bulk material in a silo bag, and then segmenting the densified material into modules optimized for efficient transport. The specific fuel use for chopping and then compacting biomass crops in the silo bag ranged from 1.6 to 3.0 L·Mg−1 and 0.5 to 1.3 L·Mg−1

77 FR 19008 - Guidelines for Home Energy Professionals: Standard Work Specifications for Single Family Energy...

Science.gov (United States)

2012-03-29

.... The development of the Guidelines for Home Energy Professionals: Standard Work Specifications for... DEPARTMENT OF ENERGY Office of Energy Efficiency and Renewable Energy Guidelines for Home Energy Professionals: Standard Work Specifications for Single Family Energy Upgrades AGENCY: Office of Energy...

77 FR 23238 - Guidelines for Home Energy Professionals: Standard Work Specifications for Single Family Energy...

Science.gov (United States)

2012-04-18

...: Comments on the Guidelines for Home Energy Professionals: Standard Work Specifications for Single Family... DEPARTMENT OF ENERGY Office of Energy Efficiency and Renewable Energy Guidelines for Home Energy Professionals: Standard Work Specifications for Single Family Energy Upgrades AGENCY: Office of Energy...

Magnitude of regge cut contributions in the triple-regge region

International Nuclear Information System (INIS)

Bartels, J.; Kramer, G.

1976-09-01

Starting from the reggeon calculus, the various possibilities of absorptive Pomeron cut corrections in the triple-Regge region are considered. For the case of pp→pX, we estimate their importance at present day energies. We conclude that at highest ISR energies Pomeron cuts of the eikonal type are not enough, and enhanced diagrams with at least one additional triple Pomeron coupling need to be included. (orig.) [de

Improved cutting performance in high power laser cutting

DEFF Research Database (Denmark)

Olsen, Flemming Ove

2003-01-01

Recent results in high power laser cutting especially with focus on cutting of mild grade steel types for shipbuilding are described.......Recent results in high power laser cutting especially with focus on cutting of mild grade steel types for shipbuilding are described....

Cutting force measurement of electrical jigsaw by strain gauges

International Nuclear Information System (INIS)

Kazup, L; Varadine Szarka, A

2016-01-01

This paper describes a measuring method based on strain gauges for accurate specification of electric jigsaw's cutting force. The goal of the measurement is to provide an overall perspective about generated forces in a jigsaw's gearbox during a cutting period. The lifetime of the tool is affected by these forces primarily. This analysis is part of the research and development project aiming to develop a special linear magnetic brake for realizing automatic lifetime tests of electric jigsaws or similar handheld tools. The accurate specification of cutting force facilitates to define realistic test cycles during the automatic lifetime test. The accuracy and precision resulted by the well described cutting force characteristic and the possibility of automation provide new dimension for lifetime testing of the handheld tools with alternating movement. (paper)

PULSED MODE LASER CUTTING OF SHEETS FOR TAILORED BLANKS

DEFF Research Database (Denmark)

Bagger, Claus; Olsen, Flemming Ove

1999-01-01

This paper describes how the laser cutting process can be optimised in such a way that the cut sheets can subsequently be used to laser weld tailored blanks. In a number of systematic laboratory experiments the effect of cutting speed, assist gas pressure, average laser power and pulse energy...... item for parameter optimisation of laser cut sheets used for tailored blanks. It was concluded that high quality cut edges with a squareness as small as 0.015 mm may be obtained. Such edges are well suited for subsequent laser welding....... was analysed. For quality assessment the squareness, roughness and dross attachment of laser cut blanks were measured. In all tests, the medium strength steel GA 260 with a thickness of 1.8 mm was used. In this work it has been successfully demonstrated that the squareness of a cut can be used as a quality...

Grading technologies for the manufacture of innovative cutting blades

Science.gov (United States)

Rostek, Tim; Homberg, Werner

2018-05-01

Cutting blades for harvesting applications are used in a variety of agricultural machines. These parts are in contact with highly abrasive lawn clippings and often wear out within hours which results in high expensive re-sharpening maintenance. This paper relates to manufacturing techniques enhancing the durability of cutting blades based on a structural analysis of the prevailing wear mechanisms containing chipping and abrasive wear. Each mechanism results in specific demands on the cutting edge's mechanical characteristics. The design of evaluation methods respectively is one issue of the paper. This is basis for approaches to improve the cutting edge performance on purpose. On option to improve abrasive wear resistance and, thus, service life is the application of locally graded steel materials as semi-finished products for self-sharpening cutting blades. These materials comprise a layered structure consisting of a hard, wear resistant layer and a relatively softer layer which is lesser wear resistant. As the cutting blade is subjected to wear conditions, the less wear resistant layer wears faster than the relatively more wear resistant harder layer revealing a durable cross section of the cutting edge and, thus, cutting performance. Anyways, chipping is another key issue on the cutting edge's lifetime. Here, the cutting edges cross section by means of geometry and grind respectively as well as its mechanical properties matter. FEM analysis reveal innovative options to optimize the cross section of the blade as well as thermomechanical strengthening add further strength to reduce chipping. This paper contains a comprehensive strategy to improve cutting blades with use of innovative manufacturing technologies which apply application-specific graded mechanical characteristics and, thus, significantly improved performance characteristics.

On extracting heavy quark parameters from moments with cuts

International Nuclear Information System (INIS)

Bigi, I.I.; Uraltsev, N.

2004-01-01

We point out that the moments of the photon energy spectrum in B→X s +γ decays have a significant bias compared to the OPE expressions used to evaluate them, when a lower cut on the photon energy is imposed. This typically increases the value extracted for the apparent b quark mass by 70 MeV or more together with an even more dramatic reduction in the apparent value of the kinetic energy expectation value. These nonperturbative effects are exponential in the effective hardness of the transition, which is strongly lowered by high cuts, and do not reflect a breakdown of the 1/m b expansion itself. Similar effects in semileptonic b→c decays are briefly addressed. Accounting for the cut-related shifts brings different measurements into good agreement, when the OPE-based theory employs the 'robust' approach. We stress the utility of the second moment of E γ , once the aforementioned effects have been included

Twice cutting method reduces tibial cutting error in unicompartmental knee arthroplasty.

Science.gov (United States)

Inui, Hiroshi; Taketomi, Shuji; Yamagami, Ryota; Sanada, Takaki; Tanaka, Sakae

2016-01-01

Bone cutting error can be one of the causes of malalignment in unicompartmental knee arthroplasty (UKA). The amount of cutting error in total knee arthroplasty has been reported. However, none have investigated cutting error in UKA. The purpose of this study was to reveal the amount of cutting error in UKA when open cutting guide was used and clarify whether cutting the tibia horizontally twice using the same cutting guide reduced the cutting errors in UKA. We measured the alignment of the tibial cutting guides, the first-cut cutting surfaces and the second cut cutting surfaces using the navigation system in 50 UKAs. Cutting error was defined as the angular difference between the cutting guide and cutting surface. The mean absolute first-cut cutting error was 1.9° (1.1° varus) in the coronal plane and 1.1° (0.6° anterior slope) in the sagittal plane, whereas the mean absolute second-cut cutting error was 1.1° (0.6° varus) in the coronal plane and 1.1° (0.4° anterior slope) in the sagittal plane. Cutting the tibia horizontally twice reduced the cutting errors in the coronal plane significantly (Pcutting the tibia horizontally twice using the same cutting guide reduced cutting error in the coronal plane. Copyright © 2014 Elsevier B.V. All rights reserved.

Prediction of individual patient response to chemotherapy by the fluorometric microculture cytotoxicity assay (FMCA) using drug specific cut-off limits and a Bayesian model.

Science.gov (United States)

Larsson, R; Nygren, P

1993-01-01

The semiautomated fluorometric microculture cytotoxicity assay (FMCA) based on the measurement of fluorescence generated from cellular hydrolysis of fluorescein diacetate (FDA) to fluorescein in microtiter plates, has been used for determination of cytotoxic drug resistance of tumor cells from patients with hematological and solid tumors. In the present study we describe a calibration procedure based on statistically derived cut-off limits and assay-predicted response probabilities using Bayes' theorem. Test results at a specified drug concentration were divided into three categories: low, intermediate or extreme drug resistance (LDR, IDR and EDR, respectively) using the median and median +1 standard deviation as the cut-off limits. When correlated with clinical outcome, LDR samples showed a higher response rate than expected, IDR a lower and EDR samples no response at all. The sensitivity and specificity of the test, using the median as cut-off limit, were 0.92 and 0.69 respectively. By fitting these test characteristics to a statistical model based on Bayes' theorem it is possible to calculate response probabilities for each individual patient taking into consideration not only the test characteristics and the particular assay result, but also the clinical and patient specific characteristics influencing the pre-test probability of response. EDR predicts clinical drug resistance with high specificity and is also observed in tumor types with high response rate.

Combustion-assisted laser cutting of a difficult-to-machine superalloy

International Nuclear Information System (INIS)

Molian, P.A.

1992-01-01

In laser cutting, the largest single application of lasers in manufacturing, the assist gas plays an important role in affecting the cutting performance. The assist gas is usually oxygen or an inert gas. In this paper acetylene and oxygen was employed to create combustion reactions during CO 2 laser cutting that enabled an improvement in the cutting speed, and cut quality of a difficult-to-machine superalloy. A comparison with laser cutting of a plain carbon steel under identical conditions was also made to determine the usefulness of combustion energy. Results indicate that both cutting speed and quality are enhanced by the reduction in the viscosity of slag formed during cutting (which assisted in ejection of the slag through the bottom of the kerf) due to the heat released by the acetylene burning inside the kerf. Correlations of experimental data with a theoretical model provided the influence of combustion power and gas-flow power on the cutting phenomena

Novel fungal disease in complex leaf-cutting ant societies

DEFF Research Database (Denmark)

Hughes, David Peter; Evans, Harry C.; Hywel-Jones, Nigel

2009-01-01

1. The leaf-cutting ants practise an advanced system of mycophagy where they grow a fungus as a food source. As a consequence of parasite threats to their crops, they have evolved a system of morphological, behavioural, and chemical defences, particularly against fungal pathogens (mycopathogens). 2....... Specific fungal diseases of the leaf-cutting ants themselves have not been described, possibly because broad spectrum anti-fungal defences against mycopathogens have reduced their susceptibility to entomopathogens. 3. Using morphological and molecular tools, the present study documents three rare infection...... events of Acromyrmex and Atta leaf-cutting ants by Ophiocordyceps fungi, agenus of entomopathogens that is normally highly specific in its host choice. 4. As leaf-cutting ants have been intensively studied, the absence of prior records of Ophiocordyceps suggests that these infections may be a novel event...

Technological development of machine tools using less energy in fiscal 2000. Achievement report on research and development of cutting process replacing electric discharge processing; 2000 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Hoden kako wo chikansuru sessaku kakoho no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development has been made with an objective to replace the electric discharge processing consuming a large amount of energy and having environmental load, with the cutting process consuming less energy while maintaining the equivalent processing precision. This paper summarizes the achievements in fiscal 2000. Development of cutting tools has made three times or more as many multi-aspect utilization as compared to conventional tools possible by researching the tip shapes. In addition, ultra hard end mill suitable for cutting very hard materials using an ultrasonic cutting head was fabricated on the trial basis, and its cutting capability was verified. In developing the cutting processing heard, a vibration mode possible of cutting with the ultra hard tool was generated, ATC has become possible, and the possibility of cutting hard-to-cut materials was verified. For processing a narrow and deep part, an improved type tool was developed, whereas the practical cutting performance suppressing wear of the blade tip was obtained. To deal with the environment, development and prototype fabrication were performed on a unit having a grease lubricated high-speed main shaft that is considered to be the mainstream in the future. In the operation test at 20,000 min-L, know-how was acquired in relation with the basic performance, manufacture and use of the unit. (NEDO)

ADVANCED CUTTINGS TRANSPORT STUDY

Energy Technology Data Exchange (ETDEWEB)

Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Mark Pickell; Len Volk; Mike Volk; Barkim Demirdal; Affonso Lourenco; Evren Ozbayoglu; Paco Vieira; Lei Zhou

2000-01-30

This is the second quarterly progress report for Year 2 of the ACTS project. It includes a review of progress made in Flow Loop development and research during the period of time between Oct 1, 2000 and December 31, 2000. This report presents a review of progress on the following specific tasks: (a) Design and development of an Advanced Cuttings Transport Facility (Task 2: Addition of a foam generation and breaker system), (b) Research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (c) Research project (Task 7): ''Study of Cuttings Transport with Aerated Muds Under LPAT Conditions (Joint Project with TUDRP)'', (d) Research project (Task 8): ''Study of Flow of Synthetic Drilling Fluids Under Elevated Pressure and Temperature Conditions'', (e) Research project (Task 9): ''Study of Foam Flow Behavior Under EPET Conditions'', (f) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions'', (g) Research on instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), and Foam properties while transporting cuttings. (Task 12), (h) Development of a Safety program for the ACTS Flow Loop. Progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S). (i) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members. The tasks Completed During This Quarter are Task 7 and Task 8.

Ag-catalysed cutting of multi-walled carbon nanotubes

International Nuclear Information System (INIS)

La Torre, A; Rance, G A; Miners, S A; Lucas, C Herreros; Smith, E F; Giménez-López, M C; Khlobystov, A N; Fay, M W; Brown, P D; Zoberbier, T; Kaiser, U

2016-01-01

In this work, the cutting of carbon nanotubes is investigated using silver nanoparticles deposited on arc discharge multi-walled carbon nanotubes. The composite is subsequently heated in air to fabricate shortened multi-walled nanotubes. Complementary transmission electron microscopy and spectroscopy techniques shed light on the cutting mechanism. The nanotube cutting is catalysed by the fundamental mechanism based on the coordination of the silver atoms to the π-bonds of carbon nanotubes. As a result of the metal coordination, the strength of the carbon–carbon bond is reduced, promoting the oxidation of carbon at lower temperature when heated in air, or lowering the activation energy required for the removal of carbon atoms by electron beam irradiation, assuring in both cases the cutting of the nanotubes. (paper)

Using laser to measure stem thickness and cut weed stems

DEFF Research Database (Denmark)

Heisel, T.; Schou, Jørgen; Andreasen, C.

2002-01-01

Stem thickness of the weed Solanum nigrum and the crop sugarbeet was determined with a He-Ne laser using a novel non-destructive technique measuring stem shadow. Thereafter, the stems were cut close to the soil surface with a CO2 laser. Treatments were carried out on pot plants, grown....... A binary model was also tested. The non-linear model incorporating stem thickness described the data best, indicating that it would be possible to optimize laser cutting by measuring stem thickness before cutting. The general tendency was that more energy was needed the thicker the stem. Energy uses...... in the greenhouse, at two different growth stages, and plant dry matter was measured 2-5 weeks after treatment. The relationship between plant dry weight and laser energy was analysed using two different non-linear dose-response regression models; one model included stem thickness as a variable, the other did not...

ADVANCED CUTTINGS TRANSPORT STUDY

Energy Technology Data Exchange (ETDEWEB)

Stefan Miska; Troy Reed; Ergun Kuru

2004-09-30

The Advanced Cuttings Transport Study (ACTS) was a 5-year JIP project undertaken at the University of Tulsa (TU). The project was sponsored by the U.S. Department of Energy (DOE) and JIP member companies. The objectives of the project were: (1) to develop and construct a new research facility that would allow three-phase (gas, liquid and cuttings) flow experiments under ambient and EPET (elevated pressure and temperature) conditions, and at different angle of inclinations and drill pipe rotation speeds; (2) to conduct experiments and develop a data base for the industry and academia; and (3) to develop mechanistic models for optimization of drilling hydraulics and cuttings transport. This project consisted of research studies, flow loop construction and instrumentation development. Following a one-year period for basic flow loop construction, a proposal was submitted by TU to the DOE for a five-year project that was organized in such a manner as to provide a logical progression of research experiments as well as additions to the basic flow loop. The flow loop additions and improvements included: (1) elevated temperature capability; (2) two-phase (gas and liquid, foam etc.) capability; (3) cuttings injection and removal system; (4) drill pipe rotation system; and (5) drilling section elevation system. In parallel with the flow loop construction, hydraulics and cuttings transport studies were preformed using drilling foams and aerated muds. In addition, hydraulics and rheology of synthetic drilling fluids were investigated. The studies were performed under ambient and EPET conditions. The effects of temperature and pressure on the hydraulics and cuttings transport were investigated. Mechanistic models were developed to predict frictional pressure loss and cuttings transport in horizontal and near-horizontal configurations. Model predictions were compared with the measured data. Predominantly, model predictions show satisfactory agreements with the measured data. As a

Modelling and optimization of cut quality during pulsed Nd:YAG laser cutting of thin Al-alloy sheet for straight profile

Science.gov (United States)

Sharma, Amit; Yadava, Vinod

2012-02-01

Thin sheets of aluminium alloys are widely used in aerospace and automotive industries for specific applications. Nd:YAG laser beam cutting is one of the most promising sheetmetal cutting process for cutting sheets for any profile. Al-alloy sheets are difficult to cut by laser beam because of its highly reflective nature. This paper presents modelling and optimization of cut quality during pulsed Nd:YAG laser cutting of thin Al-alloy sheet for straight profile. In the present study, four input process parameters such as oxygen pressure, pulse width, pulse frequency, and cutting speed and two output parameters such as average kerf taper ( Ta) and average surface roughness ( Ra) are considered. The hybrid approach comprising of Taguchi methodology (TM) and response surface methodology (RSM) is used for modelling whereas multi-objective optimization is performed using hybrid approach of TM and grey relational analysis (GRA) coupled with entropy measurement methodology. The entropy measurement methodology is employed for the calculation of weight corresponding to each quality characteristic. The results indicate that the hybrid approaches applied for modelling and optimization of the LBC process are reasonable.

Constructing a Model for Safe Nuclear Energy. General Conference Event to Focus on Innovative Cross-cutting Approach to Nuclear Safety

International Nuclear Information System (INIS)

Verlini, Giovanni

2011-01-01

Two innovative IAEA Extra-Budgetary Programmes, supporting safe nuclear energy in Bulgaria and Romania, passed their one-year milestone in 2010. Funded by the Norwegian government, these programmes are unique in that they cover separate but cross-cutting issues related to nuclear safety, including safety culture, safety assessments, risk management and resource management.

Comparison of cutting efficiency with different diamond burs and water flow rates in cutting lithium disilicate glass ceramic.

Science.gov (United States)

Siegel, Sharon C; Patel, Tejas

2016-10-01

This study compared different diamond burs and different water flow rates on the cutting efficiency of sectioning through lithium disilicate glass ceramic. The authors used a standardized cutting regimen with 4 brands of diamond burs to section through lithium disilicate glass ceramic blocks. Twelve diamonds of each brand cut through the blocks in randomized order. In the first part of the study, the authors recorded sectioning rates in millimeters per minute for each diamond bur as a measure of cutting efficiency. In the second part of the study, the authors compared sectioning rates using only 1 brand of diamond bur, with 3 different water flow rates. The authors averaged and compared cutting rates of each brand of diamond bur and the cutting rates for each flow rate using an analysis of variance and determined the differences with a Tukey honest significant difference test. One diamond bur cut significantly slower than the other 3, and one diamond bur cut significantly faster than 2 of the others. The diamond bur cutting efficiency through lithium disilicate glass ceramic with a 20 mL/min water flow rate was significantly higher than 15 mL/min. There are differences in cutting efficiency between diamond burs when sectioning lithium disilicate glass ceramic. Use a minimum of 20 mL/min of water coolant flow when sectioning lithium disilicate glass ceramic with dental diamond burs to maximize cutting efficiency. Recommendations for specific diamond burs with a coarse grit and water flow rate of 20 mL/min can be made when removing or adjusting restorations made from lithium disilicate glass ceramic. Copyright © 2016 American Dental Association. Published by Elsevier Inc. All rights reserved.

universal specific energy curve for para- bolic open channels

African Journals Online (AJOL)

DEPT OF AGRICULTURAL ENGINEERING

UNIVERSAL SPECIFIC ENERGY CURVE FOR PARA-. BOLIC OPEN CHANNELS. K.O. Aiyesimoju. Department of Civil Engineering. University of Lagos. Lagos, Nigeria. ABSTRACT. From the general relationship between specific energy and flow depth for all open channels, the specific relationship for parabolic open ...

Non-Poissonian photon statistics from macroscopic photon cutting materials

NARCIS (Netherlands)

De Jong, Mathijs; Meijerink, A; Rabouw, Freddy T.

2017-01-01

In optical materials energy is usually extracted only from the lowest excited state, resulting in fundamental energy-efficiency limits such as the Shockley-Queisser limit for single-junction solar cells. Photon-cutting materials provide a way around such limits by absorbing high-energy photons and

Direct effects of ionizing radiation on integral membrane proteins. Noncovalent energy transfer requires specific interpeptide interactions

International Nuclear Information System (INIS)

Jhun, E.; Jhun, B.H.; Jones, L.R.; Jung, C.Y.

1991-01-01

The 12 transmembrane alpha helices (TMHs) of human erythrocyte glucose transporter were individually cut by pepsin digestion as membrane-bound 2.5-3.5-kDa peptide fragments. Radiation-induced chemical degradation of these fragments showed an average target size of 34 kDa. This is 10-12 x larger than the average size of an individual TMH, demonstrating that a significant energy transfer occurs among these TMHs in the absence of covalent linkage. Heating this TMH preparation at 100 degree C for 15 min reduced the target size to 5 kDa or less, suggesting that the noncovalent energy transfer requires specific helix-helix interactions. Purified phospholamban, a small (6-kDa) integral membrane protein containing a single TMH, formed a pentameric assembly in sodium dodecyl sulfate. The chemical degradation target size of this phospholamban pentamer was 5-6 kDa, illustrating that not all integral membrane protein assemblies permit intersubunit energy transfer. These findings together with other published observations suggest strongly that significant noncovalent energy transfer can occur within the tertiary and quaternary structure of membrane proteins and that as yet undefined proper molecular interactions are required for such covalent energy transfer. Our results with pepsin-digested glucose transporter also illustrate the importance of the interhelical interaction as a predominating force in maintaining the tertiary structure of a transmembrane protein

Laser capture microdissection: Arcturus(XT) infrared capture and UV cutting methods.

Science.gov (United States)

Gallagher, Rosa I; Blakely, Steven R; Liotta, Lance A; Espina, Virginia

2012-01-01

Laser capture microdissection (LCM) is a technique that allows the precise procurement of enriched cell populations from a heterogeneous tissue under direct microscopic visualization. LCM can be used to harvest the cells of interest directly or can be used to isolate specific cells by ablating the unwanted cells, resulting in histologically enriched cell populations. The fundamental components of laser microdissection technology are (a) visualization of the cells of interest via microscopy, (b) transfer of laser energy to a thermolabile polymer with either the formation of a polymer-cell composite (capture method) or transfer of laser energy via an ultraviolet laser to photovolatize a region of tissue (cutting method), and (c) removal of cells of interest from the heterogeneous tissue section. Laser energy supplied by LCM instruments can be infrared (810 nm) or ultraviolet (355 nm). Infrared lasers melt thermolabile polymers for cell capture, whereas ultraviolet lasers ablate cells for either removal of unwanted cells or excision of a defined area of cells. LCM technology is applicable to an array of applications including mass spectrometry, DNA genotyping and loss-of-heterozygosity analysis, RNA transcript profiling, cDNA library generation, proteomics discovery, and signal kinase pathway profiling. This chapter describes the unique features of the Arcturus(XT) laser capture microdissection instrument, which incorporates both infrared capture and ultraviolet cutting technology in one instrument, using a proteomic downstream assay as a model.

Specific energy consumption in microwave drying of garlic cloves

Energy Technology Data Exchange (ETDEWEB)

Sharma, G.P. [Department of Processing and Food Engineering, College of Technology and Agricultural Engineering, Udaipur 313 001, Rajasthan (India); Prasad, Suresh [Agricultural and Food Engineering Department, Indian Institute of Technology, Kharagpur 721 302 (India)

2006-09-15

The convective and microwave-convective drying of garlic cloves was carried out in a laboratory scale microwave dryer, which was developed for this purpose. The specific energy consumption involved in the two drying processes was estimated from the energy supplied to the various components of the dryer during the drying period. The specific energy consumption was computed by dividing the total energy supplied by amount of water removed during the drying process. The specific energy consumption in convective drying of garlic cloves at 70{sup o}C temperature and 1.0m/s air velocity was estimated as 85.45MJ/kg of water evaporated. The increase in air velocity increased the energy consumption. The specific energy consumption at 40W of microwave power output, 70{sup o}C air temperature and 1.0m/s air velocity was 26.32MJ/kg of water removed, resulting in about a 70% energy saving as compared to convective drying processes. The drying time increased with increase in air velocity in microwave-convective drying process; a trend reverse to what was observed in convective drying process of garlic cloves. (author)

Fibre laser cutting stainless steel: Fluid dynamics and cut front morphology

Science.gov (United States)

Pocorni, Jetro; Powell, John; Deichsel, Eckard; Frostevarg, Jan; Kaplan, Alexander F. H.

2017-01-01

In this paper the morphology of the laser cut front generated by fibre lasers was investigated by observation of the 'frozen' cut front, additionally high speed imaging (HSI) was employed to study the fluid dynamics on the cut front while cutting. During laser cutting the morphology and flow properties of the melt film on the cut front affect cut quality parameters such as cut edge roughness and dross (residual melt attached to the bottom of the cut edge). HSI observation of melt flow down a laser cutting front using standard cutting parameters is experimentally problematic because the cut front is narrow and surrounded by the kerf walls. To compensate for this, artificial parameters are usually chosen to obtain wide cut fronts which are unrepresentative of the actual industrial process. This paper presents a new experimental cutting geometry which permits HSI of the laser cut front using standard, commercial parameters. These results suggest that the cut front produced when cutting medium section (10 mm thick) stainless steel with a fibre laser and a nitrogen assist gas is covered in humps which themselves are covered by a thin layer of liquid. HSI observation and theoretical analysis reveal that under these conditions the humps move down the cut front at an average speed of approximately 0.4 m/s while the covering liquid flows at an average speed of approximately 1.1 m/s, with an average melt depth at the bottom of the cut zone of approximately 0.17 mm.

Flux-line-cutting losses in type-II superconductors

International Nuclear Information System (INIS)

Clem, J.R.

1982-01-01

Energy dissipation associated with flux-line cutting (intersection and cross-joining of adjacent nonparallel vortices) is considered theoretically. The flux-line-cutting contribution to the dissipation per unit volume, arising from mutual annihilation of transverse magnetic flux, is identified as J/sub parallel/xE/sub parallel/, where J/sub parallel/ and E/sub parallel/ are the components of the current density and the electric field parallel to the magnetic induction. The dynamical behavior of the magnetic structure at the flux-line-cutting threshold is shown to be governed by a special critical-state model similar to that proposed by previous authors. The resulting flux-line-cutting critical-state model, characterized in planar geometry by a parallel critical current density J/sub c/parallel or a critical angle gradient k/sub c/, is used to calculate predicted hysteretic ac flux-line-cutting losses in type-II superconductors in which the flux pinning is weak. The relation of the theory to previous experiments is discussed

arXiv Cuts from residues: the one-loop case

CERN Document Server

Abreu, Samuel; Duhr, Claude; Gardi, Einan

2017-06-14

Using the multivariate residue calculus of Leray, we give a precise definition of the notion of a cut Feynman integral in dimensional regularization, as a residue evaluated on the variety where some of the propagators are put on shell. These are naturally associated to Landau singularities of the first type. Focusing on the one-loop case, we give an explicit parametrization to compute such cut integrals, with which we study some of their properties and list explicit results for maximal and next-to-maximal cuts. By analyzing homology groups, we show that cut integrals associated to Landau singularities of the second type are specific combinations of the usual cut integrals, and we obtain linear relations among different cuts of the same integral. We also show that all one-loop Feynman integrals and their cuts belong to the same class of functions, which can be written as parametric integrals.

The impact of a modified cutting flute implant design on osseointegration.

Science.gov (United States)

Jimbo, R; Tovar, N; Marin, C; Teixeira, H S; Anchieta, R B; Silveira, L M; Janal, M N; Shibli, J A; Coelho, P G

2014-07-01

Information concerning the effects of the implant cutting flute design on initial stability and its influence on osseointegration in vivo is limited. This study evaluated the early effects of implants with a specific cutting flute design placed in the sheep mandible. Forty-eight dental implants with two different macro-geometries (24 with a specific cutting flute design - Blossom group; 24 with a self-tapping design - DT group) were inserted into the mandibular bodies of six sheep; the maximum insertion torque was recorded. Samples were retrieved and processed for histomorphometric analysis after 3 and 6 weeks. The mean insertion torque was lower for Blossom implants (Pimplant contact (BIC) and P=0.52 for bone area fraction occupied (BAFO); at 6 weeks, P=0.55 for BIC and P=0.45 for BAFO. While no histomorphometric differences were observed, ground sections showed different healing patterns between the implants, with better peri-implant bone organization around those with the specific cutting flute design (Blossom group). Implants with the modified cutting flute design had a significantly reduced insertion torque compared to the DT implants with a traditional cutting thread, and resulted in a different healing pattern. Copyright © 2014 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Vortex cutting in superconductors

Science.gov (United States)

Vlasko-Vlasov, Vitalii K.; Koshelev, Alexei E.; Glatz, Andreas; Welp, Ulrich; Kwok, Wai-K.

2015-03-01

Unlike illusive magnetic field lines in vacuum, magnetic vortices in superconductors are real physical strings, which interact with the sample surface, crystal structure defects, and with each other. We address the complex and poorly understood process of vortex cutting via a comprehensive set of magneto-optic experiments which allow us to visualize vortex patterns at magnetization of a nearly twin-free YBCO crystal by crossing magnetic fields of different orientations. We observe a pronounced anisotropy in the flux dynamics under crossing fields and the filamentation of induced supercurrents associated with the staircase vortex structure expected in layered cuprates, flux cutting effects, and angular vortex instabilities predicted for anisotropic superconductors. At some field angles, we find formation of the vortex domains following a type-I phase transition in the vortex state accompanied by an abrupt change in the vortex orientation. To clarify the vortex cutting scenario we performed time-dependent Ginzburg-Landau simulations, which confirmed formation of sharp vortex fronts observed in the experiment and revealed a left-handed helical instability responsible for the rotation of vortices. This work was supported by the U.S. Department of Energy, Office of Science, Materials Sciences and Engineering Division.

The Effect of Femoral Cutting Guide Design Improvements for Patient-Specific Instruments

Directory of Open Access Journals (Sweden)

Oh-Ryong Kwon

2015-01-01

Full Text Available Although the application of patient-specific instruments (PSI for total knee arthroplasty (TKA increases the cost of the surgical procedure, PSI may reduce operative time and improve implant alignment, which could reduce the number of revision surgeries. We report our experience with TKA using PSI techniques in 120 patients from March to December 2014. PSI for TKA were created from data provided by computed tomography (CT scans or magnetic resonance imaging (MRI; which imaging technology is more reliable for the PSI technique remains unclear. In the first 20 patients, the accuracy of bone resection and PSI stability were compared between CT and MRI scans with presurgical results as a reference; MRI produced better results. In the second and third groups, each with 50 patients, the results of bone resection and stability were compared in MRI scans with respect to the quality of scanning due to motion artifacts and experienced know-how in PSI design, respectively. The optimized femoral cutting guide design for PSI showed the closest outcomes in bone resection and PSI stability with presurgical data. It is expected that this design could be a reasonable guideline in PSI.

Cutting state identification

International Nuclear Information System (INIS)

Berger, B.S.; Minis, I.; Rokni, M.

1997-01-01

Cutting states associated with the orthogonal cutting of stiff cylinders are identified through an analysis of the singular values of a Toeplitz matrix of third order cumulants of acceleration measurements. The ratio of the two pairs of largest singular values is shown to differentiate between light cutting, medium cutting, pre-chatter and chatter states. Sequences of cutting experiments were performed in which either depth of cut or turning frequency was varied. Two sequences of experiments with variable turning frequency and five with variable depth of cut, 42 cutting experiments in all, provided a database for the calculation of third order cumulants. Ratios of singular values of cumulant matrices find application in the analysis of control of orthogonal cutting

ADVANCED CUTTINGS TRANSPORT STUDY

Energy Technology Data Exchange (ETDEWEB)

Ergun Kuru; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Len Volk; Mark Pickell; Evren Ozbayoglu; Barkim Demirdal; Paco Vieira; Affonso Lourenco

1999-10-15

This report includes a review of the progress made in ACTF Flow Loop development and research during 90 days pre-award period (May 15-July 14, 1999) and the following three months after the project approval date (July15-October 15, 1999) The report presents information on the following specific subjects; (a) Progress in Advanced Cuttings Transport Facility design and development, (b) Progress report on the research project ''Study of Flow of Synthetic Drilling Fluids Under Elevated Pressure and Temperature Conditions'', (c) Progress report on the research project ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (d) Progress report on the research project ''Study of Cuttings Transport with Aerated Muds Under LPAT Conditions (Joint Project with TUDRP)'', (e) Progress report on the research project ''Study of Foam Flow Behavior Under EPET Conditions'', (f) Progress report on the instrumentation tasks (Tasks 11 and 12) (g) Activities towards technology transfer and developing contacts with oil and service company members.

Plasma cutting or laser cutting. Plasma setsudan ka laser setsudan ka

Energy Technology Data Exchange (ETDEWEB)

Nakamura, A. (Tanaka Engineering Works Ltd., Saitama (Japan))

1991-05-01

Comparisons and discussions were made on the plasma cutting and laser cutting in sheet steel cutting, referring partly to gas cutting. Historically, the cutting has been developed from gas, plasma, and laser in that order, and currently these three methods are used mixedly. Generally, the plasma cutting is superior in cutting speed, but inferior in cut face quality, and it requires measures of dust collection. Due to high accuracy and quality in cut face, the laser cutting has been practically used for quite some time in the thin sheet industry, but medium to thick sheet cutting had a problem of unavailability of high output laser suitable for these ranges. However, the recent technologies have overcome the problem as a result of development at the authors {prime} company of a 2 kW class laser cutter capable of cutting 19 mm thick sheet. The cutter has been proven being particularly excellent in controllability. Choice of whether plasma or laser would depend upon which priority is to be taken, cost or accuracy. 15 figs., 3 tabs.

Sustainable manufacturing by calculating the energy demand during turning of AISI 1045 steel

Science.gov (United States)

Nur, R.; Nasrullah, B.; Suyuti, M. A.; Apollo

2018-01-01

Sustainable development will become important issues for many fields, including production, industry, and manufacturing. In order to achieve sustainable development, industry should be able to perform of sustainable production processes and environmentally friendly. Therefore, there is need to minimize the energy demand in the machining process. This paper presents a calculation method of energy consumption in the machining process, especially turning process which calculated by summing the number of energy consumption, such as the electric energy consumed during the machining preparation, the electrical energy during the cutting processes, and the electrical energy to produce a cutting tool. A case study was performed on dry turning of mild carbon steel using coated carbide. This approach can be used to determine the total amount of electrical energy consumed in the specific machining process. It concluded that the energy consumption will be an increase for using the high cutting speed as well as for the feed rate was increased.

Parametric studies of cutting zircaloy-2 sheets with a laser beam

International Nuclear Information System (INIS)

Ghosh, S.; Badgujar, B.P.; Goswami, G.L.

1996-01-01

The highly reactive and pyrophoric nature of zirconium alloys limits the use of conventional thermal sources (e.g., plasma arc cutting, oxygen flame cutting, etc.) for the cutting and drilling of these alloys. In this context, a highly coherent laser beam provides a good alternative for the cutting and drilling. In the present paper, laser beam cutting of zircaloy-2 sheets of 1.1 mm and 0.74 mm thickness is performed using a 300 W average power pulsed Nd:YAG laser. Pulse energy, pulse repetition rate, nozzle gap, gas pressure and cutting speed were varied to give different laser cutting conditions. Metallographic study of the cut surfaces showed the presence of transformed beta phase in the heat affected zone (HAZ) near the cut surface. The microhardness value across the cut surface was also measured. It showed a gradual increase in microhardness from the base metal (160 VHN) towards the HAZ having a maximum value of 365 VHN. The results of parametric studies of the cutting indicated that, with proper selection of process parameters, very narrow cuts can be easily made in zircaloy-2 using a pulsed Nd:YAG laser with a saving in material and at a much faster rate than alternative processes such as plasma arc cutting and oxygen flame cutting

Wedge cutting of mild steel by CO 2 laser and cut-quality assessment in relation to normal cutting

Science.gov (United States)

Yilbas, B. S.; Karatas, C.; Uslan, I.; Keles, O.; Usta, Y.; Yilbas, Z.; Ahsan, M.

2008-10-01

In some applications, laser cutting of wedge surfaces cannot be avoided in sheet metal processing and the quality of the end product defines the applicability of the laser-cutting process in such situations. In the present study, CO 2 laser cutting of the wedge surfaces as well as normal surfaces (normal to laser beam axis) is considered and the end product quality is assessed using the international standards for thermal cutting. The cut surfaces are examined by the optical microscopy and geometric features of the cut edges such as out of flatness and dross height are measured from the micrographs. A neural network is introduced to classify the striation patterns of the cut surfaces. It is found that the dross height and out of flatness are influenced significantly by the laser output power, particularly for wedge-cutting situation. Moreover, the cut quality improves at certain value of the laser power intensity.

The Effects of Operational Parameters on a Mono-wire Cutting System: Efficiency in Marble Processing

Science.gov (United States)

Yilmazkaya, Emre; Ozcelik, Yilmaz

2016-02-01

Mono-wire block cutting machines that cut with a diamond wire can be used for squaring natural stone blocks and the slab-cutting process. The efficient use of these machines reduces operating costs by ensuring less diamond wire wear and longer wire life at high speeds. The high investment costs of these machines will lead to their efficient use and reduce production costs by increasing plant efficiency. Therefore, there is a need to investigate the cutting performance parameters of mono-wire cutting machines in terms of rock properties and operating parameters. This study aims to investigate the effects of the wire rotational speed (peripheral speed) and wire descending speed (cutting speed), which are the operating parameters of a mono-wire cutting machine, on unit wear and unit energy, which are the performance parameters in mono-wire cutting. By using the obtained results, cuttability charts for each natural stone were created on the basis of unit wear and unit energy values, cutting optimizations were performed, and the relationships between some physical and mechanical properties of rocks and the optimum cutting parameters obtained as a result of the optimization were investigated.

High-energy azimuthally polarized laser beam generation from an actively Q-switched Nd:YAG laser with c-cut YVO4 crystal

Science.gov (United States)

Guo, Jing; Zhang, Baofu; Jiao, Zhongxing; He, Guangyuan; Wang, Biao

2018-05-01

A high-energy, azimuthally polarized (AP) and actively Q-switched Nd:YAG laser is demonstrated. The thermal bipolar lensing effect in the Nd:YAG laser rod is used as a polarization discriminator, and a c-cut YVO4 crystal is inserted into the laser cavity to increase the mode-selecting ability of the cavity for AP mode. The laser generated AP pulses with maximum pulse energy as high as 4.2 mJ. To the best of our knowledge, this is the highest pulse energy obtained from an actively Q-switched AP laser. The pulse energy remained higher than 1 mJ over a wide range of repetition rates from 5 kHz to 25 kHz.

Speichim cuts ethanol energy

Energy Technology Data Exchange (ETDEWEB)

1981-05-08

France's Speichim has reported low-pressure steam consumption of only 0.7kg/l in the production of industrial-grade ethanol. Mechanical compression of distillation vapours can reduce this energy demand even more.

A novel patterning effect during high frequency laser micro-cutting of hard ceramics for microelectronics applications

Energy Technology Data Exchange (ETDEWEB)

Savriama, Guillaume, E-mail: guillaume.savriama@gmail.com [GREMI-UMR 7344, CNRS/Univ-Orléans, 14 rue d’Issoudun, BP 6744, F-45067 Orléans (France); STMicroelectronics, 10 rue Thalès de Milet, CS 97155, 37071 Tours Cedex 2 (France); Jarry, Vincent; Barreau, Laurent [STMicroelectronics, 10 rue Thalès de Milet, CS 97155, 37071 Tours Cedex 2 (France); Boulmer-Leborgne, Chantal; Semmar, Nadjib [GREMI-UMR 7344, CNRS/Univ-Orléans, 14 rue d’Issoudun, BP 6744, F-45067 Orléans (France)

2014-05-01

This paper investigates the laser micro-cutting of wide band gap materials for microelectronics industry purposes. An ultraviolet (355 nm) diode-pumped solid-state (DPSS) nanosecond laser was used in this investigation. The laser energy varied from 7 to 140 μJ/pulse with typical frequencies from 40 to 200 kHz. The effect of pulse energy and scanning speed on the depth of the cutting street of α-Al{sub 2}O{sub 3} and glass was studied. Typical depths of 200 μm were achieved on α-Al{sub 2}O{sub 3} for 140 μJ/pulse, 40 kHz at 13 mm/s. SEM images showed periodic patterns produced by periodic explosive boiling that can influence the achieved depth. The shape, size and periodicity of the recast material depended on the feed rate and the laser beam frequency. This periodic removal mechanism seems to be specific to dielectrics since it was not observed for semiconductors such as silicon or silicon carbide.

Cutting work in thick section cryomicrotomy.

Science.gov (United States)

Saubermann, A J; Riley, W D; Beeuwkes, R

1977-09-01

The forces during cryosectioning were measured using miniature strain gauges attached to a load cell fitted to the drive arm of the Porter-Blum MT-2 cryomicrotome. Work was calculated and the data normalized to a standard (1 mm X 1 mm X 0.5 micrometer) section. Thermal energy generated was also calculated. Five parameters were studied: cutting angle, thickness, temperature, hardness, and block shape. Force patterns could be divided into three major groups thought to represent cutting (Type I), large fracture planes greater than 10 micrometer in length (Type II), and small fracture planes less than 10 micrometer in length (Type III). Type I and Type II produced satisfactory sections. Work in cutting ranged from an average of 78.4 muJ to 568.8 muJ. Cutting angle and temperature had the greatest effect on sectioning. Heat generated would be sufficient to cause through-section melting for 0.5 micrometer thick sections assuming the worst possible case, namely that all heat went into the section without loss. Presence of a Type II pattern (large fracture pattern) is thought to be presumptive evidence against thawing.

The results of cutting disks testing for rock destruction

Directory of Open Access Journals (Sweden)

Khoreshok Aleksey

2017-01-01

Full Text Available To determine the rational order of disk tools placement on the working body is necessary to know the maximum amount of rock, destroyed by the disk tool in benching cutting mode depending on the tool geometry parameters, physical and mechanical parameters of rocks. The article contains the definition of rational parameters of cutting disk tools as well as power and energy parameters of the destruction process by cutting disks and by executive body of the coal cutter. The rational geometric parameters of cutting discs are specified. It was found that each step of cutting with a minimum depth of penetration has its own maximum height of bench outcrop. The dependence of the volumes of large items destroyed by the disk tool on the cutting step height was determined. The existence of the cyclic alternation of destruction phases, regardless the fracture parameters, the height of the ledge outcrop, and tools like free cutting geometry were found. In contrast to the free cutting in benching mode of destruction two large fragments of rocks in one cycle were observed. Consequently, the cyclical nature of the destruction process in the benching mode will be characterized by two chips and crushing, and this cycling repeats throughout the destruction process with the same parameters of destruction.

Integration of Small-Diameter Wood Harvesting in Early Thinnings using the Two pile Cutting Method

Energy Technology Data Exchange (ETDEWEB)

Kaerhae, Kalle (Metsaeteho Oy, P.O. Box 101, FI-00171 Helsinki (Finland))

2008-10-15

Metsaeteho Oy studied the integrated harvesting of industrial roundwood (pulpwood) and energy wood based on a two-pile cutting method, i.e. pulpwood and energy wood fractions are stacked into two separate piles when cutting a first-thinning stand. The productivity and cost levels of the integrated, two-pile cutting method were determined, and the harvesting costs of the two-pile method were compared with those of conventional separate wood harvesting methods. In the time study, when the size of removal was 50 dm3, the productivity in conventional whole-tree cutting was 6% higher than in integrated cutting. With a stem size of 100 dm3, the productivity in whole-tree cutting was 7% higher than in integrated cutting. The results indicated, however, that integrated harvesting based on the two-pile method enables harvesting costs to be decreased to below the current cost level of separate pulpwood harvesting in first thinning stands. The greatest cost-saving potential lies in small-sized first thinnings. The results showed that, when integrated wood harvesting based on the two-pile method is applied, the removals of both energy wood and pulpwood should be more than 15-20 m3/ha at the harvesting sites in order to achieve economically viable integrated procurement

Specific energy released in power reactors

International Nuclear Information System (INIS)

Zaritskaya, T.S.; Kiselev, G.V.; Rudik, A.P.; Tsenter, Eh.M.

1986-01-01

Technique of determination are described and analysis of specific energy for different methods of critically maintance of RBMK and WWER-440 reactors are conducted. Characteristics of the optimal mode of critically maintanance are determined

MULTI-OBJECTIVE OPTIMISATION OF LASER CUTTING USING CUCKOO SEARCH ALGORITHM

Directory of Open Access Journals (Sweden)

M. MADIĆ

2015-03-01

Full Text Available Determining of optimal laser cutting conditions for improving cut quality characteristics is of great importance in process planning. This paper presents multi-objective optimisation of the CO2 laser cutting process considering three cut quality characteristics such as surface roughness, heat affected zone (HAZ and kerf width. It combines an experimental design by using Taguchi’s method, modelling the relationships between the laser cutting factors (laser power, cutting speed, assist gas pressure and focus position and cut quality characteristics by artificial neural networks (ANNs, formulation of the multiobjective optimisation problem using weighting sum method, and solving it by the novel meta-heuristic cuckoo search algorithm (CSA. The objective is to obtain optimal cutting conditions dependent on the importance order of the cut quality characteristics for each of four different case studies presented in this paper. The case studies considered in this study are: minimisation of cut quality characteristics with equal priority, minimisation of cut quality characteristics with priority given to surface roughness, minimisation of cut quality characteristics with priority given to HAZ, and minimisation of cut quality characteristics with priority given to kerf width. The results indicate that the applied CSA for solving the multi-objective optimisation problem is effective, and that the proposed approach can be used for selecting the optimal laser cutting factors for specific production requirements.

Slicing Cuts on Food Materials Using Robotic-Controlled Razor Blade

Directory of Open Access Journals (Sweden)

Debao Zhou

2011-01-01

Full Text Available Cutting operations using blades can arise in a number of industries, for example, food processing industry, in which cheese, fruit and vegetable, even meat, are involved. Certain questions will rise during these works, such as “why pressing-and-slicing cuts use less force than pressing-only cuts” and “how is the influence of the blade cutting-edge on force”. To answer these questions, this research developed a mathematical expression of the cutting stress tensor. Based on the analysis of the stress tensor on the contact surface, the influence of the blade edge-shape and slicing angle on the resultant cutting force were formulated and discussed. These formulations were further verified using experimental results by robotic cutting of potatoes. Through studying the change of the cutting force, the optimal slicing angle can be obtained in terms of maximum feeding distance and minimum cutting force. Based on the blade sharpness properties and the specific materials, the required cutting force can be predicted. These formulation and experimental results explained the basic theory of blade cutting fracture and further provided the support to optimize the cutting mechanism design and to develop the force control algorithms for the automation of blade cutting operations.

Specific Energy of Hard Coal Under Load

Directory of Open Access Journals (Sweden)

Bogusz Anna

2015-03-01

Full Text Available The article presents results of experimental tests of energy parameters of hard coals under loading, collected from research sites located within five main geologic structures of Upper Silesian Coal Basin (GZW - Main Trough, Main Anticline, Bytom Trough, Rybnik Trough and Chwałowice Trough. Coals from12 mines were analysed, starting with seams of group 200, through groups 400, 500, 600 and, finally, seams of group 700. Coal of each of the groups of seams underwent uniaxial compression stress of the energy parameters, in a servo-controlled testing machine MTS-810NEW, for the full range of strain of the tested coal samples. Based on the tests the dependence of different types of specific energy of longitudinal strain of coals on the value of uniaxial compression strength was determined. The dependence of the value of dissipated energy and kinetic energy of coals on the uniaxial compression strength was described with a linear function, both for coals which due to their age belong to various bed sand for various lithotypes of coal. An increase in the value of dissipated energy and in kinetic energy was observed, which was correlated with an increase in uniaxial compression strength of coal. The share of dissipated energy is dominant in the total energy of strain. Share of recoverable energy in the total energy of strain is small, independent of the compression strength of coals and is at most a few per cent high. In coals of low strength and dominant share of dissipated energy, share of recoverable energy is the biggest among the tested coals. It was shown that following an increase in compression strength the share of recoverable energy decreases, while the share of dissipated energy in the total energy increases. Further studies of specific energy of longitudinal strain of rocks in the full-range strain will be the next step inperfecting methodology of research into natural rock burst susceptibility of Carboniferous rock mass and changes in the

Quality Testing of Short Rotation Coppice Willow Cuttings

Directory of Open Access Journals (Sweden)

Katrin Heinsoo

2018-06-01

Full Text Available The production and feasibility of Short Rotation Coppice depend on cutting early performance. The shoot and root biomass production of Salix cuttings in hydroponic conditions was studied. The amount of sprouted biomass after four weeks of growth depended on cutting the diameter, but the original position of the cutting along the rod or number of visible buds was not in correlation with biomass produced. Application of mineral fertilizer or soil originating from the willow plantation did not increase the total production. On the contrary, the addition of soil tended to decrease biomass production and we assumed this was a result of a shortage of light. Under the influence of fertilization, plants allocated greater biomass to roots. Comparison of different clones revealed that those with S. dasyclados genes tended to allocate less biomass to roots and the poorest-performing clone in our experiment, also had the lowest wood production in the plantation. The number of visible buds on the cutting was also clone-specific.

Classifying post-stroke fatigue: Optimal cut-off on the Fatigue Assessment Scale.

Science.gov (United States)

Cumming, Toby B; Mead, Gillian

2017-12-01

Post-stroke fatigue is common and has debilitating effects on independence and quality of life. The Fatigue Assessment Scale (FAS) is a valid screening tool for fatigue after stroke, but there is no established cut-off. We sought to identify the optimal cut-off for classifying post-stroke fatigue on the FAS. In retrospective analysis of two independent datasets (the '2015' and '2007' studies), we evaluated the predictive validity of FAS score against a case definition of fatigue (the criterion standard). Area under the curve (AUC) and sensitivity and specificity at the optimal cut-off were established in the larger 2015 dataset (n=126), and then independently validated in the 2007 dataset (n=52). In the 2015 dataset, AUC was 0.78 (95% CI 0.70-0.86), with the optimal ≥24 cut-off giving a sensitivity of 0.82 and specificity of 0.66. The 2007 dataset had an AUC of 0.83 (95% CI 0.71-0.94), and applying the ≥24 cut-off gave a sensitivity of 0.84 and specificity of 0.67. Post-hoc analysis of the 2015 dataset revealed that using only the 3 most predictive FAS items together ('FAS-3') also yielded good validity: AUC 0.81 (95% CI 0.73-0.89), with sensitivity of 0.83 and specificity of 0.75 at the optimal ≥8 cut-off. We propose ≥24 as a cut-off for classifying post-stroke fatigue on the FAS. While further validation work is needed, this is a positive step towards a coherent approach to reporting fatigue prevalence using the FAS. Copyright © 2017 Elsevier Inc. All rights reserved.

The effect of cutting conditions on power inputs when machining

Science.gov (United States)

Petrushin, S. I.; Gruby, S. V.; Nosirsoda, Sh C.

2016-08-01

Any technological process involving modification of material properties or product form necessitates consumption of a certain power amount. When developing new technologies one should take into account the benefits of their implementation vs. arising power inputs. It is revealed that procedures of edge cutting machining are the most energy-efficient amongst the present day forming procedures such as physical and technical methods including electrochemical, electroerosion, ultrasound, and laser processing, rapid prototyping technologies etc, such as physical and technical methods including electrochemical, electroerosion, ultrasound, and laser processing, rapid prototyping technologies etc. An expanded formula for calculation of power inputs is deduced, which takes into consideration the mode of cutting together with the tip radius, the form of the replaceable multifaceted insert and its wear. Having taken as an example cutting of graphite iron by the assembled cutting tools with replaceable multifaceted inserts the authors point at better power efficiency of high feeding cutting in comparison with high-speed cutting.

Direct Energy Conversion for Nuclear Propulsion at Low Specific Mass

Science.gov (United States)

Scott, John H.

2014-01-01

The project will continue the FY13 JSC IR&D (October-2012 to September-2013) effort in Travelling Wave Direct Energy Conversion (TWDEC) in order to demonstrate its potential as the core of a high potential, game-changing, in-space propulsion technology. The TWDEC concept converts particle beam energy into radio frequency (RF) alternating current electrical power, such as can be used to heat the propellant in a plasma thruster. In a more advanced concept (explored in the Phase 1 NIAC project), the TWDEC could also be utilized to condition the particle beam such that it may transfer directed kinetic energy to a target propellant plasma for the purpose of increasing thrust and optimizing the specific impulse. The overall scope of the FY13 first-year effort was to build on both the 2012 Phase 1 NIAC research and the analysis and test results produced by Japanese researchers over the past twenty years to assess the potential for spacecraft propulsion applications. The primary objective of the FY13 effort was to create particle-in-cell computer simulations of a TWDEC. Other objectives included construction of a breadboard TWDEC test article, preliminary test calibration of the simulations, and construction of first order power system models to feed into mission architecture analyses with COPERNICUS tools. Due to funding cuts resulting from the FY13 sequestration, only the computer simulations and assembly of the breadboard test article were completed. The simulations, however, are of unprecedented flexibility and precision and were presented at the 2013 AIAA Joint Propulsion Conference. Also, the assembled test article will provide an ion current density two orders of magnitude above that available in previous Japanese experiments, thus enabling the first direct measurements of power generation from a TWDEC for FY14. The proposed FY14 effort will use the test article for experimental validation of the computer simulations and thus complete to a greater fidelity the

Cutting thin glass by femtosecond laser ablation

Science.gov (United States)

Shin, Hyesung; Kim, Dongsik

2018-06-01

The femtosecond laser ablation process for cutting thin aluminoborosilicate glass sheets of thickness 100 μm was investigated with emphasis on effective cutting speed (Veff) and mechanical strength of diced samples. The process parameters including the laser fluence (F), overlap ratio (r) of the laser beam and polarization direction were varied at a fixed pulse repetition rate f = 1 kHz to find the optimal process condition that maximizes Veff and edge strength. A three-point bending test was performed to evaluate the front-side and back-side bending (edge) strength of the laser-cut samples. Veff was proportional to F unless r exceeded a critical value, at which excessive energy began to be delivered at the same spot. The front-side edge strength was bigger than the back-side strength because of the back-side damages such as chipping. Good edge strength, as high as ∼280 MPa (front-side) and ∼230 MPa (back-side), was obtained at F = 19 J/m2, r = 0.99, with laser polarization vertical to the cutting path.

Aspects of plasma arc cutting process in the AISI 321 type stainless steel

International Nuclear Information System (INIS)

Souza Barros, I. de.

1985-01-01

Some aspects of plasma arc cutting process in the AISI321 stainless steel, used in nuclear industry, are analysed. The maximum values of the velocity of cutting and, the minimum quantity of energy per unit of length necesary for the plasma were determined. The localization of irregularities in the cut surface in function of the velocity of cutting was investigated. The cut surfaces were evaluated by surface roughness, using as measurement parameter, the distance between the sharpest salience and the deepest reentrance of the sample profile. The width of layer from thermal action of the plasma was influenced by the velocity of cutting. (Author) [pt

Laser Cutting of Thick Diamond Films Using Low-Power Laser

Energy Technology Data Exchange (ETDEWEB)

Park, Y.J.; Baik, Y.J. [Korea Institute of Science and Technology, Seoul (Korea)

2000-02-01

Laser cutting of thick diamond films is studied rising a low-power(10 W) copper vapor laser. Due to the existence of the saturation depth in laser cutting, thick diamond films are not easily cut by low-power lasers. In this study, we have adopted a low thermal- conductivity underlayer of alumina and a heating stage (up to 500 deg. C in air) to prevent the laser energy from consuming-out and, in turn, enhance the cutting efficiency. Aspect ratio increases twice from 3.5 to 7 when the alumina underlayer used. Adopting a heating stage also increases aspect ratio and more than 10 is obtained at higher temperatures than 400 deg. C. These results show that thick diamond films can be cut, with low-power lasers, simply by modifying the thermal property of underlayer. (author). 13 refs., 5 figs.

Cutting performances with new industrial continuous wave ND:YAG high power lasers

International Nuclear Information System (INIS)

Chagnot, C.; Dinechin, G. de; Canneau, G.

2010-01-01

Dismantling is a great challenge for nuclear companies which are facing with the cleaning of former nuclear sites. Among the available cutting processes is the multi-kilowatts laser whose power is transmitted through optical fibers. Unlike other cutting processes such as the plasma arc cutting process or the oxy-cutting process, the laser process can be easily implemented by robotic equipments. The mechanised robotic arm carries a laser cutting head to perform, with remote-controlled equipments, the cutting operation. The present study deals with the performances which can be reached with high power continuous wave ND:YAG lasers. The cutting tests were carried out up to 8 kW. The laser power was delivered through a specific power supply chain: a 0.4 mm fiber was transporting the power from the laser to a first interface (coupler) then a second 0.6 mm fiber was bringing the laser power to the cutting head. This solution allowed a power delivery chain whose length could be as high as 100 + 20/50 m. Another advantage of this kind of power supply is that the first fiber can be set in a non-contaminated environment whereas the second fiber lies in the contaminated area. The cutting head used for these tests was a specific tool developed for this laser dismantling work: it is a laser cutting head cooled by pressurized air. This tool was developed with the requirement to be able to sustain a laser power of 14 kW. The pressurized air used to cool the head is also used as cutting gas. The cutting capability was about 10 mm by kW. At the power of 8 kW, austenitic steel plates of thickness 100 mm were cut. These performances were reached with the cut started on the plate's edge. If the cut started in the middle of the plate, the cutting performances were not so high: 8 kW became the power to drill and to cut plates of thickness 40 mm.

Effect of ultrasonic specific energy on waste activated sludge ...

African Journals Online (AJOL)

The effect of ultrasonic specific energy on waste activated sludge (WAS) solubilization and enzyme activity was investigated in this study. Experimental results showed that the increase of ultrasonic specific energy in the range of 0 - 90000 kJ/kg dried sludge (DS) benefited WAS particle size reduction and the solubilization ...

Cutting forces during turning with variable depth of cut

Directory of Open Access Journals (Sweden)

M. Sadílek

2016-03-01

The proposed research for the paper is an experimental work – measuring cutting forces and monitoring of the tool wear on the cutting edge. It compares the turning where standard roughing cycle is used and the turning where the proposed roughing cycle with variable depth of cut is applied.

Scenarios for cutting down energy-related climate gas emissions in Germany; Szenarien zur Minderung energiebedingten Klimagasemissionen in Deutschland

Energy Technology Data Exchange (ETDEWEB)

Hake, J.F.; Kuckshinrichs, W. [Forschungszentrum Juelich (Germany). Programmgruppe Systemforschung und Technologische Entwicklung (STE)

1998-12-31

Developing successful strategies for cutting down climate gas emissions is an extremely complex task. This goal can be aimed at by a combination of measures. But the results of individual scenarios are no immediate clue to their practicability. The results of scenarios must always be discussed within the context of the assumptions made and, where applicable, the targets set. Consequently, their informative value is limited. The contribution of scenarios to the answering of energy-political issues is that they define possible scope for action. (orig.)

Development of plasma cutting process at observation of environmental requirements

International Nuclear Information System (INIS)

Czech, J.; Matusiak, J.; Pasek-Siurek, H.

1997-01-01

Plasma cutting is one of the basic methods for thermal cutting of metals. It is characterized by high productivity and quality of the cut surface. However, the plasma cutting process is one of the most harmful processes for environment and human health. It results from many agents being a potential environmental risk The large amount of dust and gases emitted during the process as well as an intensive radiation of electric arc and excessive noise are considered as the most harmful hazards. The existing ventilation and filtration systems are not able to solve all problems resulting from the process. Plasma cutting under water is worthy of notice, especially during an advancement of plasma cutting process, because of human safety and environment protection. Such a solution allows to reduce considerably the emission of dust and gases, as well as to decrease the noise level and ultraviolet radiation. An additional advantage of underwater plasma cutting is a reduction in the width of material heating zone and a decrease in strains of elements being cut. However, the productivity of this process is a little lower what results in an increase in cutting cost. In the paper, it has been presented the results of the investigations made at the Institute of Welding in Gliwice on the area of plasma cutting equipment with energy-saving inverter power supplies used in automated processes of underwater plasma cutting as well as the results of testing of welding environment contamination and safety hazards. (author)

Trends and Cut-Point Changes in Obesity Parameters by Age Groups Considering Metabolic Syndrome.

Science.gov (United States)

Park, Hyung Jun; Hong, Young Ho; Cho, Yun Jung; Lee, Ji Eun; Yun, Jae Moon; Kwon, Hyuktae; Kim, Sang Hyuck

2018-02-12

Non-communicable diseases (NCDs) are an important issue worldwide. Obesity has a close relationship with NCDs. Various age-related changes should be considered when evaluating obesity. National representative cohort data from the National Health Insurance Service National Sample Cohort from 2012 to 2013 were used. Sex-specific and age group-specific (10-year intervals) means for body mass index (BMI), waist circumference (WC), and waist-to-height ratio (WtHR) were calculated. Optimal cut-points for obesity parameters were defined as the value predicting two or more components of metabolic syndrome (except WC). The mean value and optimal cut-point for BMI decreased with age for men. The mean BMI value for women increased with age, but optimal cut-points showed no remarkable difference. The mean WC of men increased with age, but the optimal cut-points were similar for age groups. For women, the mean value and optimal cut-point for WC increased with age. Regarding WtHR, the mean value and optimal cut-point increased with age for men and women. Differences across age groups were larger for women. The mean values of the obesity indices and the optimal cut-points were changed according to age groups. This study supports the necessity of applying age group-specific cut-points for the various obesity parameters. © 2018 The Korean Academy of Medical Sciences.

Cutting method and cutting device for spent fuel rod of nuclear reactor

International Nuclear Information System (INIS)

Komatsu, Masahiko; Ose, Toshihiko.

1996-01-01

A control rod transferred under water in a vertically suspended state is postured horizontally at such a water depth that radiations can be shielded, and then it is cut to a dropping speed limiting portion and a cross-like main body. The separated cross-like main body portion is further cut in the longitudinal direction and separated into a pair of cut pieces each having an L-shaped cross section. A disk like metal saw is used as a cutting tool. Alternatively, a plasma jet cutter or a melting-type water jet cutter is used as a cutting tool. Then, since the spent control rod to be cut is postured horizontally under water, the water depth for the cutting position can be reduced. As a result, the cutting state using the cutting tool can be observed by naked eyes from the position above the water surface thereby enabling to perform the cutting operation reliably. (N.H.)

Lucky Motifs in Chinese Folk Art: Interpreting Paper-cut from Chinese Shaanxi

OpenAIRE

Xuxiao WANG

2013-01-01

Paper-cut is not simply a form of traditional Chinese folk art. Lucky motifs developed in paper-cut certainly acquired profound cultural connotations. As paper-cut is a time-honoured skill across the nation, interpreting those motifs requires cultural receptiveness and anthropological sensitivity. The author of this article analyzes examples of paper-cut from Northern Shaanxi, China, to identify the cohesive motifs and explore the auspiciousness of the specific concepts of Fu, Lu, Shou, Xi. T...

STRUCTURAL ANNOTATION OF EM IMAGES BY GRAPH CUT

Energy Technology Data Exchange (ETDEWEB)

Chang, Hang; Auer, Manfred; Parvin, Bahram

2009-05-08

Biological images have the potential to reveal complex signatures that may not be amenable to morphological modeling in terms of shape, location, texture, and color. An effective analytical method is to characterize the composition of a specimen based on user-defined patterns of texture and contrast formation. However, such a simple requirement demands an improved model for stability and robustness. Here, an interactive computational model is introduced for learning patterns of interest by example. The learned patterns bound an active contour model in which the traditional gradient descent optimization is replaced by the more efficient optimization of the graph cut methods. First, the energy function is defined according to the curve evolution. Next, a graph is constructed with weighted edges on the energy function and is optimized with the graph cut algorithm. As a result, the method combines the advantages of the level set method and graph cut algorithm, i.e.,"topological" invariance and computational efficiency. The technique is extended to the multi-phase segmentation problem; the method is validated on synthetic images and then applied to specimens imaged by transmission electron microscopy(TEM).

Cuttings-carried theory and erosion rule in gas drilling horizontal well

Directory of Open Access Journals (Sweden)

Wei Na

2014-01-01

Full Text Available In gas horizontal drilling, the gas with cuttings will go through the annulus at high speed which will lead strong erosion to the drill tools. This paper proposes a cuttings-carried theory and modified the critical cuttings-carried model for the gas-solid flow. Meanwhile, the erosive energy is obtained through simulating the gas-solid mixture in different conditions. The study result has positive significance on the determination of reasonable injection volume by optimizing construction parameters of horizontal well in gas drilling.

'Intelligent' system's cost-cutting power.

Science.gov (United States)

Dodge, Jeremy

2010-05-01

Jeremy Dodge, business manager at Marshall Tufflex Energy Management, explains how a voltage optimisation system that, in a claimed industry first, uses "auto-transformers" to reduce incoming mains electricity voltage so that electrical equipment receives precisely the "outgoing feed" it needs to function optimally and no more, thus significantly reducing wastage, can help major electricity users cut their bills "by as much as 25%".

Flexible Laser Metal Cutting

DEFF Research Database (Denmark)

Villumsen, Sigurd; Jørgensen, Steffen Nordahl; Kristiansen, Morten

2014-01-01

This paper describes a new flexible and fast approach to laser cutting called ROBOCUT. Combined with CAD/CAM technology, laser cutting of metal provides the flexibility to perform one-of-a-kind cutting and hereby realises mass production of customised products. Today’s laser cutting techniques...... possess, despite their wide use in industry, limitations regarding speed and geometry. Research trends point towards remote laser cutting techniques which can improve speed and geometrical freedom and hereby the competitiveness of laser cutting compared to fixed-tool-based cutting technology...... such as punching. This paper presents the concepts and preliminary test results of the ROBOCUT laser cutting technology, a technology which potentially can revolutionise laser cutting....

Effect of Moisture Content of Paper Material on Laser Cutting

Science.gov (United States)

Stepanov, Alexander; Saukkonen, Esa; Piili, Heidi; Salminen, Antti

Laser technology has been used in industrial processes for several decades. The most advanced development and implementation took place in laser welding and cutting of metals in automotive and ship building industries. However, there is high potential to apply laser processing to other materials in various industrial fields. One of these potential fields could be paper industry to fulfill the demand for high quality, fast and reliable cutting technology. Difficulties in industrial application of laser cutting for paper industry are associated to lack of basic information, awareness of technology and its application possibilities. Nowadays possibilities of using laser cutting for paper materials are widened and high automation level of equipment has made this technology more interesting for manufacturing processes. Promising area of laser cutting application at paper making machines is longitudinal cutting of paper web (edge trimming). There are few locations at a paper making machine where edge trimming is usually done: wet press section, calender or rewinder. Paper web is characterized with different moisture content at different points of the paper making machine. The objective of this study was to investigate the effect of moisture content of paper material on laser cutting parameters. Effect of moisture content on cellulose fibers, laser absorption and energy needed for cutting is described as well. Laser cutting tests were carried out using CO2 laser.

A new nanosecond UV laser at 355 nm: early results of corneal flap cutting in a rabbit model.

Science.gov (United States)

Trost, Andrea; Schrödl, Falk; Strohmaier, Clemens; Bogner, Barbara; Runge, Christian; Kaser-Eichberger, Alexandra; Krefft, Karolina; Vogel, Alfred; Linz, Norbert; Freidank, Sebastian; Hilpert, Andrea; Zimmermann, Inge; Grabner, Günther; Reitsamer, Herbert A

2013-12-03

A new 355 nm UV laser was used for corneal flap cutting in an animal model and tested for clinical and morphologic alterations. Corneal flaps were created (Chinchilla Bastards; n = 25) with an UV nanosecond laser at 355 nm (150 kHz, pulse duration 850 ps, spot-size 1 μm, spot spacing 6 × 6 μm, side cut Δz 1 μm; cutting depth 130 μm) and pulse energies of 2.2 or 2.5 μJ, respectively. Following slit-lamp examination, animals were killed at 6, 12, and 24 hours after treatment. Corneas were prepared for histology (hematoxylin and eosin [HE], TUNEL-assay) and evaluated statistically, followed by ultrastructural investigations. Laser treatment was tolerated well, flap lift was easier at 2.5 μJ compared with 2.2 μJ. Standard HE at 24 hours revealed intact epithelium in the horizontal cut, with similar increase in corneal thickness at both energies. Irrespective of energy levels, TUNEL assay revealed comparable numbers of apoptotic cells in the horizontal and vertical cut at 6, 12, and 24 hours, becoming detectable in the horizontal cut as an acellular stromal band at 24 hours. Ultrastructural analysis revealed regular morphology in the epi- and endothelium, while in the stroma, disorganized collagen lamellae were detectable representing the horizontal cut, again irrespective of energy levels applied. This new UV laser revealed no epi- nor endothelial damage at energies feasible for corneal flap cutting. Observed corneal swelling was lower compared with existing UV laser studies, albeit total energy applied here was much higher. Observed loss of stromal keratinocytes is comparable with available laser systems. Therefore, this new laser is suitable for refractive surgery, awaiting its test in a chronic environment.

The generalized good cut equation

International Nuclear Information System (INIS)

Adamo, T M; Newman, E T

2010-01-01

The properties of null geodesic congruences (NGCs) in Lorentzian manifolds are a topic of considerable importance. More specifically NGCs with the special property of being shear-free or asymptotically shear-free (as either infinity or a horizon is approached) have received a great deal of recent attention for a variety of reasons. Such congruences are most easily studied via solutions to what has been referred to as the 'good cut equation' or the 'generalization good cut equation'. It is the purpose of this paper to study these equations and show their relationship to each other. In particular we show how they all have a four-complex-dimensional manifold (known as H-space, or in a special case as complex Minkowski space) as a solution space.

Some possibilities for determining cutting data when using laser cutting:

OpenAIRE

Radovanović, Miroslav

2006-01-01

The technological problems faced in the field of the application of laser-cutting machines lie in insufficient knowledge of the laser technique and the absence of both sufficiently reliable practical data and knowledge about the parameters affecting the work process itself. A significant parameter that is necessary to determine and to enter in an NC-program is the cutting speed. Various authors analyze the laser-cutting process and give mathematical models where laser cutting is modeled by us...

Current Observational Constraints to Holographic Dark Energy Model with New Infrared cut-off via Markov Chain Monte Carlo Method

OpenAIRE

Wang, Yuting; Xu, Lixin

2010-01-01

In this paper, the holographic dark energy model with new infrared (IR) cut-off for both the flat case and the non-flat case are confronted with the combined constraints of current cosmological observations: type Ia Supernovae, Baryon Acoustic Oscillations, current Cosmic Microwave Background, and the observational hubble data. By utilizing the Markov Chain Monte Carlo (MCMC) method, we obtain the best fit values of the parameters with $1\\sigma, 2\\sigma$ errors in the flat model: $\\Omega_{b}h...

Remote Laser Cutting of CFRP: Improvements in the Cut Surface

Science.gov (United States)

Stock, Johannes; Zaeh, Michael F.; Conrad, Markus

In the automotive industry carbon fibre reinforced plastics (CFRP) are considered as a future key material to reduce the weight of the vehicle. Therefore, capable production techniques are required to process this material in mass industry. E.g., state of the art methods for cutting are limited by the high tool wear or the feasible feed rate. Laser cutting processes are still under investigation. This paper presents detailed new studies on remote laser cutting of CFRP focusing on the influence of the material properties and the quality of the cut surface. By adding light absorbing soot particles to the resin of the matrix, the cutting process is improved and fewer defects emerge.

Multibeam Fibre Laser Cutting

DEFF Research Database (Denmark)

Olsen, Flemming Ove

The appearance of the high power high brilliance fibre laser has opened for new possibilities in laser materials processing. In laser cutting this laser has demonstrated high cutting performance compared to the dominating cutting laser, the CO2-laser. However, quality problems in fibre......-laser cutting have until now limited its application in metal cutting. In this paper the first results of proof-of-principle studies applying a new approach (patent pending) for laser cutting with high brightness short wavelength lasers will be presented. In the approach, multi beam patterns are applied...... to control the melt flow out of the cut kerf resulting in improved cut quality in metal cutting. The beam patterns in this study are created by splitting up beams from 2 single mode fibre lasers and combining these beams into a pattern in the cut kerf. The results are obtained with a total of 550 W of single...

Multibeam fiber laser cutting

DEFF Research Database (Denmark)

Olsen, Flemming Ove; Hansen, Klaus Schütt; Nielsen, Jakob Skov

2009-01-01

The appearance of the high power high brilliance fiber laser has opened for new possibilities in laser materials processing. In laser cutting this laser has demonstrated high cutting performance compared to the dominating Cutting laser, the CO2 laser. However, quality problems in fiber......-laser cutting have until now limited its application to metal cutting. In this paper the first results of proof-of-principle Studies applying a new approach (patent pending) for laser cutting with high brightness and short wavelength lasers will be presented. In the approach, multibeam patterns are applied...... to control the melt flow out of the cut kerf resulting in improved cut quality in metal cutting. The beam patterns in this study are created by splitting up beams from two single mode fiber lasers and combining these beams into a pattern in the cut kerf. The results are obtained with a total of 550 W...

Cutting cleaner

International Nuclear Information System (INIS)

Elsen, R.P.H. van; Smits, M.

1991-01-01

This paper presents the results of a long term field test of the Cutting Cleaner, which is used for the treatment of wet oil contaminated cuttings (WOCC) produced when drilling with Oil Based Mud (OBM). It was concluded that it is possible to reduce the oil content of cuttings to an average of 1 - 2%. The recovered base oil can be reused to make new oil based mud

Human papillomavirus testing in primary cervical screening and the cut-off level for hybrid capture 2 tests

DEFF Research Database (Denmark)

Rebolj, Matejka; Bonde, Jesper; Njor, Sisse Helle

2011-01-01

To determine the trade-off between the sensitivity and the specificity for high grade cervical intraepithelial neoplasia at hybrid capture 2 cut-off values above the standard = 1 relative light units/cut-off level (rlu/co).......To determine the trade-off between the sensitivity and the specificity for high grade cervical intraepithelial neoplasia at hybrid capture 2 cut-off values above the standard = 1 relative light units/cut-off level (rlu/co)....

Chemical monitoring of mud products on drilled cuttings

International Nuclear Information System (INIS)

Hughes, T.L.; Jones, T.G.J.; Tomkins, P.G.; Gilmour, A.; Houwen, O.H.; Sanders, M.

1991-01-01

An increasing area of concern for offshore drilling practices in the environmental impact of discharged drilled cuttings contaminated with drilling fluids. The standard retort analysis is of limited accuracy and chemical specificity. Anticipating future requirements for a more complete accounting of mud chemicals discharged to the environment, we present here results for chemical monitoring using a modern comprehensive chemical analysis technique. Fourier transform infrared (FT-IR) spectrometry. In this paper description is given of sampling methods found to be practical and the main calibration requirements are discussed. The techniques developed in the course of this work give a good mineralogical breakdown of mud solids (commercial and drilled solids) in addition to the environmentally relevant measurements relating to mud on cuttings. The possibility of using the new technique for the rigsite monitoring of drilling cuttings is demonstrated. Cuttings samples simultaneously from the flow line, shaker screen, desilter and mud cleaner were analyzed. It is found that mud polymers and other organic additives can be measured with sufficient accuracy to measure the removal of mud products by discharged cuttings. The technique is also applicable to quantify the losses of oil-based mud on cuttings. Field testing has shown that the instrumentation used in sufficiently robust and simple to use for rig-site application

Secondary proton production at small atmospheric depths as a function of the geomagnetic cut-off

Energy Technology Data Exchange (ETDEWEB)

Papini, P. [Florence Univ. (Italy)]|[INFN, Florence (Italy); Grimani, C. [Perugia Univ. (Italy)]|[INFN, Perugia (Italy); Stephens, S.A. [Tata Institute of Fundamental Research, Bombay (International Commission on Radiation Units and Measurements)

1995-09-01

A detailed calculation of the energy spectrum of secondary protons in the atmosphere is being carried out in the energy range 20 MeV - 40 GeV. In this calculation, it is taken into account all processes leading to the production of secondary protons as a function of the atmospheric depth has been calculated using all relevant energy loss processes. In this paper, it is examine the effect of the geomagnetic cut-off on the spectral shape of secondary protons specially at energies below the geomagnetic cut-off for small atmospheric depths.

Secondary proton production at small atmospheric depths as a function of the geomagnetic cut-off

International Nuclear Information System (INIS)

Papini, P.; Grimani, C.; Stephens, S.A.

1995-01-01

A detailed calculation of the energy spectrum of secondary protons in the atmosphere is being carried out in the energy range 20 MeV - 40 GeV. In this calculation, it is taken into account all processes leading to the production of secondary protons as a function of the atmospheric depth has been calculated using all relevant energy loss processes. In this paper, it is examine the effect of the geomagnetic cut-off on the spectral shape of secondary protons specially at energies below the geomagnetic cut-off for small atmospheric depths

High Energy Cutting and Stripping Utilizing Liquid Nitrogen

Science.gov (United States)

Hume, Howard; Noah, Donald E.; Hayes, Paul W.

2005-01-01

The Aerospace Industry has endeavored for decades to develop hybrid materials that withstand the rigors of mechanized flight both within our atmosphere and beyond. The development of these high performance materials has led to the need for environmentally friendly technologies for material re-work and removal. The NitroJet(TM) is a fluid jet technology that represents an evolution of the widely used, large-scale water jet fluid jet technology. It involves the amalgamation of fluid jet technology and cryogenics technology to create a new capability that is applicable where water jet or abrasive jet (water jet plus entrained abrasive) are not suitable or acceptable because of technical constraints such as process or materials compatibility, environmental concerns and aesthetic or legal requirements. The NitroJet(TM) uses ultra high-pressure nitrogen to cut materials, strip numerous types of coatings such as paint or powder coating, clean surfaces and profile metals. Liquid nitrogen (LN2) is used as the feed stream and is pressurized in two stages. The first stage pressurizes sub cooled LN2 to an intermediate pressure of between 15,000 and 20,000 psi at which point the temperature of the LN2 is about -250 F. The discharge from this stage is then introduced as feed to a dual intensifier system, which boosts the pressure from 15,000 - 20,000 psi up to the maximum operating pressure of 55,000 psi. A temperature of about -220 F is achieved at which point the nitrogen is supercritical. In this condition the nitrogen cuts, strips and abrades much like ultra high-pressure water would but without any residual liquid to collect, remove or be contaminated. Once the nitrogen has performed its function it harmlessly flashes back into the atmosphere as pure nitrogen gas. The system uses heat exchangers to control and modify the temperature of the various intake and discharge nitrogen streams. Since the system is hydraulically operated, discharge pressures can be easily varied over

Laser cutting or water-jet cutting. Laser setsudan ka water-jet setsudan ka

Energy Technology Data Exchange (ETDEWEB)

Yamada, T. (Shibuya Kogyo Co. Ltd., Ishikawa (Japan))

1991-05-01

The recent spread of carbon oxide laser cutter is so startlingly fast, but at the same time, water jet cutting using ultra high pressure water stream is drawing attention as it has identical characteristics, and opens the way to cutting materials that have been hitherto difficult to cut. The authors, who are fabricators of cutters of both types, gave the comparisons and explanations on several examples referring to materials that can be cut, cutting accuracy, speed, shape and thermal effects to cut face, and running cost in detail. However, simple comparison is difficult. For instance, cutting 6 mm thick SUS sheet costs a running cost of 65 yen per meter in laser cutting, and 535 yen per meter in water jet cutting, but this situation is often reversed when other material or sheet thickness is selected. The actual situation in the sheet metal processing industry at the present time is that it uses by far more laser processing machines, and uses water jet cutters to supplement for cutting materials more difficult to cut. 10 figs., 3 tabs.

Technology development for cutting a reactor pressure vessel using a mechanical cutting technique

International Nuclear Information System (INIS)

Watanabe, Masaaki; Miyasaka, Yasuhiko; Miyao, Hidehiko; Ooki, Arahiko; Ninomiya, Toshiaki; Koiwai, Masami

2001-01-01

On decommissioning of nuclear facilities, the thermal cutting technique such as an oxygen-acetylene gas cutting and a plasma arc cutting are generally used for cutting massive and thick steel structures in consideration with cutting speed and control performance. These techniques generate dust, smoke, aerosol and a large quantity of secondary waste. Mechanical cutting technique has an advantage of small amount of secondary waste, and the metal chips from the kerf recovered easily compared with these thermal cutting technique. The remote mechanical cutting system for highly activated RPV has been developed with the manner which achieves the safety and cost effectiveness. The development has been performed on consignment to RANDEC from the Science and Technology Agency of Japan. (author)

Machining of Some Difficult-to-Cut Materials with Rotary Cutting Tools

OpenAIRE

Stjernstoft, Tero

2004-01-01

Automobile and aero industries have an increasing interestin materials with improved mechanical properties. However, manyof these new materials are classified as difficult-to-cut withconventional tools. It is obvious that tools, cutting processesand cutting models has to be devel-oped parallel to materialsscience. In this thesis rotary cutting tools are tested as analternative toexpensive diamond or cubic bore nitridetools. Metal matrix composites mostly consist of a light metalalloy (such as...

The effect of spending cuts on teen pregnancy.

Science.gov (United States)

Paton, David; Wright, Liam

2017-07-01

In recent years, English local authorities have been forced to make significant cuts to devolved expenditure. In this paper, we examine the impact of reductions in local expenditure on one particular public health target: reducing rates of teen pregnancy. Contrary to predictions made at the time of the cuts, panel data estimates provide no evidence that areas which reduced expenditure the most have experienced relative increases in teenage pregnancy rates. Rather, expenditure cuts are associated with small reductions in teen pregnancy rates, a result which is robust to a number of alternative specifications and tests for causality. Underlying socio-economic factors such as education outcomes and alcohol consumption are found to be significant predictors of teen pregnancy. Copyright © 2017 Elsevier B.V. All rights reserved.

Cross cutting CFD support to innovative reactor design

International Nuclear Information System (INIS)

Roelofs, Ferry

2009-01-01

Several innovative technologies are under consideration in the world for nuclear energy production. The considered reactor systems apply either gas, sodium, lead, lead-bismuth, supercritical water, or molten salt as coolant. Therefore, methods shall be developed to determine the viability of such systems, but also to support the design of these innovative reactor systems. Computational Fluid Dynamics (CFD) is becoming more and more integrated in the daily practice of thermal-hydraulics researchers and designers. Therefore, it is very important to develop modelling approaches for the application of CFD to the specific requirements for innovative reactors. As many of these innovative reactor designs under consideration are operated using other coolants than water, one has to be careful in adopting methods which are developed for water as a coolant. Cross-cutting CFD challenges, methods and applications are presented for innovative reactors. (author)

Minimizing waste (off-cuts using cutting stock model: The case of one dimensional cutting stock problem in wood working industry

Directory of Open Access Journals (Sweden)

Gbemileke A. Ogunranti

2016-09-01

Full Text Available Purpose: The main objective of this study is to develop a model for solving the one dimensional cutting stock problem in the wood working industry, and develop a program for its implementation. Design/methodology/approach: This study adopts the pattern oriented approach in the formulation of the cutting stock model. A pattern generation algorithm was developed and coded using Visual basic.NET language. The cutting stock model developed is a Linear Programming (LP Model constrained by numerous feasible patterns. A LP solver was integrated with the pattern generation algorithm program to develop a one - dimensional cutting stock model application named GB Cutting Stock Program. Findings and Originality/value: Applying the model to a real life optimization problem significantly reduces material waste (off-cuts and minimizes the total stock used. The result yielded about 30.7% cost savings for company-I when the total stock materials used is compared with the former cutting plan. Also, to evaluate the efficiency of the application, Case I problem was solved using two top commercial 1D-cutting stock software.  The results show that the GB program performs better when related results were compared. Research limitations/implications: This study round up the linear programming solution for the number of pattern to cut. Practical implications: From Managerial perspective, implementing optimized cutting plans increases productivity by eliminating calculating errors and drastically reducing operator mistakes. Also, financial benefits that can annually amount to millions in cost savings can be achieved through significant material waste reduction. Originality/value: This paper developed a linear programming one dimensional cutting stock model based on a pattern generation algorithm to minimize waste in the wood working industry. To implement the model, the algorithm was coded using VisualBasic.net and linear programming solver called lpsolvedll (dynamic

A cutting-edge solution for 1µm laser metal processing

Science.gov (United States)

Baumbach, N.; Kühl, P.; Karam, J.; Jonkers, J.; Villarreal-Saucedo, F.; Reyes, M.

2017-02-01

The recent 1μm-laser cutting market is dominated by fiber and disk lasers due to their excellent beam quality of below 4mm*mrad. Teradiode's 4kW direct diode laser source achieves similar beam quality while having a different beam shape and shorter wavelengths which are known for higher absorption rates at the inclined front of the cutting keyhole. Research projects, such as the HALO Project, have additionally shown that polarized radiation and beams with shapes different from the typical LG00 lead to improved cut quality for ferrous and non-ferrous metals. [1] Diode laser have the inherent property of not being sensitive to back reflection which brings advantages in cutting high-reflective materials. The II-VI HIGHYAG laser cutting head BIMO-FSC offers the unique feature of machine controlled and continuous adjustment of both the focus diameter and the focus position. This feature is proven to be beneficial for cutting and piercing with high speed and small hole diameters. In addition, the optics are designed for lowest focus shift. As a leading laser processing head manufacturer, II-VI HIGHYAG qualified its BIMO-FSC MZ (M=magnification, Z=focus position) cutting head for Teradiode's 4kW direct diode laser source to offer a cutting-edge solution for highpower laser cutting. Combining the magnification ability of the cutting head with this laser source, customers experience strong advantages in cutting metals in broad thickness ranges. Thicknesses up to 25mm mild steel can easily be cut with excellent edge quality. Furthermore, a new optical setup equivalent to an axicon with a variable axicon angle is demonstrated which generates variable sized ring spots. The setup provides new degrees of freedom to tailor the energy distribution for even higher productivity and quality.

A Quality Function Deployment-Based Model for Cutting Fluid Selection

Directory of Open Access Journals (Sweden)

Kanika Prasad

2016-01-01

Full Text Available Cutting fluid is applied for numerous reasons while machining a workpiece, like increasing tool life, minimizing workpiece thermal deformation, enhancing surface finish, flushing away chips from cutting surface, and so on. Hence, choosing a proper cutting fluid for a specific machining application becomes important for enhanced efficiency and effectiveness of a manufacturing process. Cutting fluid selection is a complex procedure as the decision depends on many complicated interactions, including work material’s machinability, rigorousness of operation, cutting tool material, metallurgical, chemical, and human compatibility, reliability and stability of fluid, and cost. In this paper, a decision making model is developed based on quality function deployment technique with a view to respond to the complex character of cutting fluid selection problem and facilitate judicious selection of cutting fluid from a comprehensive list of available alternatives. In the first example, HD-CUTSOL is recognized as the most suitable cutting fluid for drilling holes in titanium alloy with tungsten carbide tool and in the second example, for performing honing operation on stainless steel alloy with cubic boron nitride tool, CF5 emerges out as the best honing fluid. Implementation of this model would result in cost reduction through decreased manpower requirement, enhanced workforce efficiency, and efficient information exploitation.

CO2 laser cutting

CERN Document Server

Powell, John

1998-01-01

The laser has given manufacturing industry a new tool. When the laser beam is focused it can generate one of the world's most intense energy sources, more intense than flames and arcs, though similar to an electron beam. In fact the intensity is such that it can vaporise most known materials. The laser material processing industry has been growing swiftly as the quality, speed and new manufacturing possibilities become better understood. In the fore of these new technologies is the process of laser cutting. Laser cutting leads because it is a direct process substitu­ tion and the laser can usually do the job with greater flexibility, speed and quality than its competitors. However, to achieve these high speeds with high quality con­ siderable know how and experience is required. This information is usually carefully guarded by the businesses concerned and has to be gained by hard experience and technical understanding. Yet in this book John Powell explains in lucid and almost non­ technical language many o...

Rescue US energy innovation

Science.gov (United States)

Anadon, Laura Diaz; Gallagher, Kelly Sims; Holdren, John P.

2017-10-01

President Trump has proposed severe cuts to US government spending on energy research, development and demonstration, but Congress has the `power of the purse' and can rescue US energy innovation. If serious cuts are enacted, the pace of innovation will slow, harming the economy, energy security and global environmental quality.

Performance Analysis of a Hybrid Power Cutting System for Roadheader

Directory of Open Access Journals (Sweden)

Yang Yang

2017-01-01

Full Text Available An electrohydraulic hybrid power cutting transmission system for roadheader under specific working condition was proposed in this paper. The overall model for the new system composed of an electric motor model, a hydraulic pump-motor model, a torsional planetary set model, and a hybrid power train model was established. The working mode characteristics were simulated under the conditions of taking the effect of cutting picks into account. The advantages of new hybrid power cutting system about the dynamic response under shock load were investigated compared with the traditional cutting system. The results illustrated that the hybrid power system had an obvious cushioning in terms of the dynamic load of cutting electric motor and planetary gear set. Besides, the hydraulic motor could provide an auxiliary power to improve the performance of the electric motor. With further analysis, a dynamic load was found to have a high relation to the stiffness and damping of coupling in the transmission train. The results could be a useful guide for the design of cutting transmission of roadheader.

Welding and cutting

International Nuclear Information System (INIS)

Drews, P.; Schulze Frielinghaus, W.

1978-01-01

This is a survey, with 198 literature references, of the papers published in the fields of welding and cutting within the last three years. The subjects dealt with are: weldability of the materials - Welding methods - Thermal cutting - Shaping and calculation of welded joints - Environmental protection in welding and cutting. (orig.) [de

Sinuous Flow in Cutting of Metals

Science.gov (United States)

Yeung, Ho; Viswanathan, Koushik; Udupa, Anirudh; Mahato, Anirban; Chandrasekar, Srinivasan

2017-11-01

Using in situ high-speed imaging, we unveil details of a highly unsteady plastic flow mode in the cutting of annealed and highly strain-hardening metals. This mesoscopic flow mode, termed sinuous flow, is characterized by repeated material folding, large rotation, and energy dissipation. Sinuous flow effects a very large shape transformation, with local strains of ten or more, and results in a characteristic mushroomlike surface morphology that is quite distinct from the well-known morphologies of metal-cutting chips. Importantly, the attributes of this unsteady flow are also fundamentally different from other well-established unsteady plastic flows in large-strain deformation, like adiabatic shear bands. The nucleation and development of sinuous flow, its dependence on material properties, and its manifestation across material systems are demonstrated. Plastic buckling and grain-scale heterogeneity are found to play key roles in triggering this flow at surfaces. Implications for modeling and understanding flow stability in large-strain plastic deformation, surface quality, and preparation of near-strain-free surfaces by cutting are discussed. The results point to the inadequacy of the widely used shear-zone models, even for ductile metals.

Schlieren technique applied to the arc temperature measurement in a high energy density cutting torch

International Nuclear Information System (INIS)

Prevosto, L.; Mancinelli, B.; Artana, G.; Kelly, H.

2010-01-01

Plasma temperature and radial density profiles of the plasma species in a high energy density cutting arc have been obtained by using a quantitative schlieren technique. A Z-type two-mirror schlieren system was used in this research. Due to its great sensibility such technique allows measuring plasma composition and temperature from the arc axis to the surrounding medium by processing the gray-level contrast values of digital schlieren images recorded at the observation plane for a given position of a transverse knife located at the exit focal plane of the system. The technique has provided a good visualization of the plasma flow emerging from the nozzle and its interactions with the surrounding medium and the anode. The obtained temperature values are in good agreement with those values previously obtained by the authors on the same torch using Langmuir probes.

Cutting assembly

Science.gov (United States)

Racki, Daniel J.; Swenson, Clark E.; Bencloski, William A.; Wineman, Arthur L.

1984-01-01

A cutting apparatus includes a support table mounted for movement toward and away from a workpiece and carrying a mirror which directs a cutting laser beam onto the workpiece. A carrier is rotatably and pivotally mounted on the support table between the mirror and workpiece and supports a conduit discharging gas toward the point of impingement of the laser beam on the workpiece. Means are provided for rotating the carrier relative to the support table to place the gas discharging conduit in the proper positions for cuts made in different directions on the workpiece.

Environmental sampling: Issues for the cut-off regime

International Nuclear Information System (INIS)

Fearey, B.L.

1995-01-01

The fissile material cut-off treaty (FMCT) initiative under the Conference on Disarmament mandate is envisioned to include certain aspects of environmental sampling and monitoring. One of the intents of this treaty is to bring certain non-NPT signatories (e.g., threshold states) under this treaty agreement along with the nuclear weapon states (NWSs). This paper provides a brief overview of some of the relevant issues that may be involved in the implementation and use of environmental monitoring for (1) verification of the cut-off regime declarations, (2) the detection of undeclared activities, and, (3) application in non-routine inspections. The intent is to provide backstopping information important for treaty negotiators. Specific issues addressed within this paper include signature sampling, differences in the proposed detection regime, potential signature integrators, specific examples and spoofing concerns. Many of these issues must be carefully considered and weighed in order to create a credibly verifiable inspection regime. Importantly, the cut-off treaty must enable nondiscriminatory implementation, while carefully assuring that nonproliferation treaty requirements are maintained (i.e., preventing unintentional release of critical weapons design information--potentially through environmental sampling and analysis)

Restraining and neck cutting or stunning and neck cutting of veal calves.

Science.gov (United States)

Lambooij, E; van der Werf, J T N; Reimert, H G M; Hindle, V A

2012-05-01

Brain and heart activities were measured in 31 veal calves during restraining and rotating followed by neck cutting with or without stunning to evaluate welfare. After neck cutting correlation dimension analyses and %power of EEG beta wave fraction decreased gradually to lower values resulting in an induction of unconsciousness lasting on average 80s. Corneal reflex response ceased 135±57s after neck cutting. The CD scores and the %power of beta waves fell immediately after post-cut captive bolt and pre-cut electrical stunning to levels indicating unconsciousness. Heart rate in lairage increased upon entrance to the restrainer and again after rotation, heart rate variability decreased. Rotating the restrainer 90°, 120° or 180° compromised veal calf welfare and should be avoided. It is recommended to use post-cut captive bolt stunning or pre-cut electrical stunning inducing immediate unconsciousness. Copyright © 2011 Elsevier Ltd. All rights reserved.

Numerical analysis of the effect of the TEM00 radiation mode polarisation on the cut shape in laser cutting of thick metal sheets

International Nuclear Information System (INIS)

Zaitsev, A V; Kovalev, O B; Orishich, Anatolii M; Fomin, V M

2005-01-01

The effect of polarisation of a Gaussian beam on the radiation absorption during laser cutting of metals is investigated. A generalised formula is proposed for calculating the absorption coefficient, which describes the polarisation of three types (linear, elliptical, and circular), taking into account the fact that the beam may interact with a metal surface of an arbitrary shape. A comparison with the existing analogues (in the cases of linear and circular radiation polarisation) confirmed the advantage of employing the formula for the spatial description of the shape of the surface produced, which is highly important for processing (cutting, welding, drilling) of thick materials. The effect of laser radiation characteristics on the surface shape and cut depth in cutting stainless steel sheets is investigated numerically. It is shown for the first time that the cutting of materials by the TEM 00 beam is most efficient when the beam has elliptical polarisation directed along the direction of beam displacement and characterised by a specific axial ratio. (laser applications and other topics in quantum electronics)

Building Partnerships to Cut Petroleum Use in Transportation

Energy Technology Data Exchange (ETDEWEB)

None

2014-02-26

The U.S. Department of Energy's Clean Cities initiative advances the nation's economic, environmental, and energy security by supporting local actions to cut petroleum use in transportation. Clean Cities accomplishes this work through the activities of nearly 100 local coalitions. These coalitions provide resources and technical assistance in the deployment of alternative and renewable fuels, idle-reduction measures, fuel economy improvements, and new transportation technologies as they emerge.

A spatial estimation model for continuous rock mass characterization from the specific energy of a TBM

Science.gov (United States)

Exadaktylos, G.; Stavropoulou, M.; Xiroudakis, G.; de Broissia, M.; Schwarz, H.

2008-12-01

Basic principles of the theory of rock cutting with rolling disc cutters are used to appropriately reduce tunnel boring machine (TBM) logged data and compute the specific energy (SE) of rock cutting as a function of geometry of the cutterhead and operational parameters. A computational code written in Fortran 77 is used to perform Kriging predictions in a regular or irregular grid in 1D, 2D or 3D space based on sampled data referring to rock mass classification indices or TBM related parameters. This code is used here for three purposes, namely: (1) to filter raw data in order to establish a good correlation between SE and rock mass rating (RMR) (or tunnelling quality index Q) along the chainage of the tunnel, (2) to make prediction of RMR, Q or SE along the chainage of the tunnel from boreholes at the exploration phase and design stage of the tunnel, and (3) to make predictions of SE and RMR or Q ahead of the tunnel’s face during excavation of the tunnel based on SE estimations during excavation. The above tools are the basic constituents of an algorithm to continuously update the geotechnical model of the rock mass based on logged TBM data. Several cases were considered to illustrate the proposed methodology, namely: (a) data from a system of twin tunnels in Hong Kong, (b) data from three tunnels excavated in Northern Italy, and (c) data from the section Singuerlin-Esglesias of the Metro L9 tunnel in Barcelona.

Drill cuttings mount formation study

Science.gov (United States)

Teh, Su Yean; Koh, Hock Lye

2014-07-01

Oil, Gas and Energy sector has been identified as an essential driving force in the Malaysian Economic Transformation Programs (ETP). Recently confirmed discovery of many offshore oil and gas deposits in Malaysian waters has ignited new confidence in this sector. However, this has also spurred intense interest on safeguarding the health and environment of coastal waters in Malaysia from adverse impact resulting from offshore oil and gas production operation. Offshore discharge of spent drilling mud and rock cuttings is the least expensive and simplest option to dispose of large volumes of drilling wastes. But this onsite offshore disposal may have adverse environmental impacts on the water column and the seabed. It may also pose occupational health hazards to the workers living in the offshore platforms. It is therefore important to model the transport and deposition of drilling mud and rock cuttings in the sea to enable proper assessment of their adverse impacts on the environment and the workers. Further, accumulation of drill particles on the seabed may impede proper operation of pipelines on the seabed. In this paper, we present an in-house application model TUNA-PT developed to cater to local oil and gas industry needs to simulate the dispersion and mount formation of drill cuttings by offshore oil and gas exploration and production platforms. Using available data on Malaysian coastal waters, simulation analyses project a pile formation on the seabed with a maximum height of about 1 m and pile radius of around 30 to 50 m. Simulated pile heights are not sensitive to the heights of release of the cuttings as the sensitivity has been mitigated by the depth of water.

Towards crack-free ablation cutting of thin glass sheets with picosecond pulsed lasers

Science.gov (United States)

Sun, Mingying; Eppelt, Urs; Hartmann, Claudia; Schulz, Wolfgang; Zhu, Jianqiang; Lin, Zunqi

2017-08-01

We investigated the morphology and mechanism of laser-induced damage in the ablation cutting of thin glass sheets with picosecond laser. Two kinds of damage morphologies observed on the cross-section of the cut channel, are caused by high-density free-electrons and the temperature accumulation, respectively. Notches and micro-cracks can be observed on the top surface of the sample near the cut edge. The surface micro-cracks were related to high energy free-electrons and also the heat-affected zone. Heat-affected-zone and visible-cracks free conditions of glass cutting were achieved by controlling the repetition rate and spatial overlap of laser pulses.

Comparison of Fixed Diameter-Limit and Selection Cutting in Northern Conifers

Science.gov (United States)

Laura S. Kenefic; Paul E. Sendak; John C. Brissette

2005-01-01

Diameter-limit cutting is a common type of harvest in which all merchantable trees above specific size thresholds are removed. Despite a long history of application, controlled experiments of these harvests are rare and the cumulative effects of repeated diameter-limit cuts are largely unknown. The Penobscot Experimental Forest in Maine is the location of a long-term...

Cross-Cutting Activities 2016 on Wind Turbine Noise, Summary Report

DEFF Research Database (Denmark)

Bertagnolio, Franck; Aagaard Madsen, Helge; Fischer, Andreas

2017-01-01

The goal of this report is to summarize activities that took place in year 2016 as part of the Cross-Cutting Activity on Wind Turbine Noise, self-financed by DTU Wind Energy. A short description of the background behind this project (in particular Cross-Cutting Activities conducted in year 2015......), the main objectives of the various studies and scientific achievements are reported in the introduction. Then, each Work Packages constituting this project are described in more details in the following sections....

A study on practical use of underwater abrasive water jet cutting

Science.gov (United States)

Yamaguchi, Hitoshi; Demura, Kenji

1993-09-01

The practicality of underwater abrasive water jet cutting technology was studied in experiments. A study of abrasives in slurried form showed that optimum polymer concentration can be selected to suit underwater conditions. For the long-distance transport of slurry from the ocean surface to the ocean floor, a direct supply system by hose proved to be practical. This system takes advantage of the insolubility of the slurry in water due to a difference in specific gravity. For cutting thick steel plate at great ocean depths, a simulation with a pressurized container revealed the requirements for actual cutting. Confirmation of remote cutting operations will become the most important technology in field applications. Underwater sound vibration characteristics were found to change significantly in direct response to modifications in cutting conditions. This will be important basic data to develop an effective sensoring method.

Paper Cuts.

Science.gov (United States)

Greene, Lisa A.

1990-01-01

Describes how to create paper cuts and suggests the most appropriate materials for young children that give good quality results. Describes the methods the author, a professional artist, uses to assemble her own paper cuts and how these can be adopted by older students. (KM)

Application of laser cutting technology to high radiation environments

International Nuclear Information System (INIS)

Pauley, K.A.; Mitchell, M.R.; Saget, S.N.

1996-01-01

A 2 kW Nd:YAG laser system manufactured by the Lumonics Corporation will be used to cut various metals during the fall of 1996 as part of a United States Department of Energy (DOE)-funded technology demonstration at the Hanford Site. The laser cutting demonstration will focus on an evaluation of two issues as the technology applies to the decontamination and decommissioning (D ampersand D) of aging nuclear facilities. An assessment will be made as to the ability of laser end effectors to be operated using electromechanical remote manipulators and the ability of both end effector and fiber optics to withstand the damage created by a high radiation field. The laser cutting demonstration will be conducted in two phases. The first phase will be a non-radioactive test to ensure the ability of hot cell remote manipulators to use the laser end effector to successfully cut the types of materials and geometries found in the hot cell. The second phase will introduce the laser end effector and the associated fiber optic cable into the hot cell radiation environment. The testing in the hot cell will investigate the degradation of the optical portions of the end effector and transmission cable in the high radiation field. The objective of the demonstration is to assess the cutting efficiency and life limitations of a laser cutting system for radioactive D ampersand D operations. A successful demonstration will, therefore, allow the laser cutting technology to be integrated into the baseline planning for the D ampersand D of DOE facilities throughout the nation

Wet cutting

Energy Technology Data Exchange (ETDEWEB)

Hole, B. [IMC Technical Services (United Kingdom)

1999-08-01

Continuous miners create dust and methane problems in underground coal mining. Control has usually been achieved using ventilation techniques as experiments with water based suppression have led to flooding and electrical problems. Recent experience in the US has led to renewed interest in wet head systems. This paper describes tests of the Hydraphase system by IMC Technologies. Ventilation around the cutting zone, quenching of hot ignition sources, dust suppression, the surface trial gallery tests, the performance of the cutting bed, and flow of air and methane around the cutting head are reviewed. 1 ref., 2 figs., 2 photos.

Fundamentals of cutting.

Science.gov (United States)

Williams, J G; Patel, Y

2016-06-06

The process of cutting is analysed in fracture mechanics terms with a view to quantifying the various parameters involved. The model used is that of orthogonal cutting with a wedge removing a layer of material or chip. The behaviour of the chip is governed by its thickness and for large radii of curvature the chip is elastic and smooth cutting occurs. For smaller thicknesses, there is a transition, first to plastic bending and then to plastic shear for small thicknesses and smooth chips are formed. The governing parameters are tool geometry, which is principally the wedge angle, and the material properties of elastic modulus, yield stress and fracture toughness. Friction can also be important. It is demonstrated that the cutting process may be quantified via these parameters, which could be useful in the study of cutting in biology.

Precision Machining When Cutting with Leading Plastic Deformation

Directory of Open Access Journals (Sweden)

N. A. Yaroslavtseva

2017-01-01

Full Text Available Keeping up the product competitiveness continually requires solving the problems of reducing time for product creation and material costs for its production and ensuring the maximum conformity of the product quality with the individual requirements of a particular consumer. It is especially difficult to implement these tasks in product manufacturing from the hard-to-machine steels and alloys with extremely low production rate in machining (often 10-20 times lower than when cutting the ordinary structural steels.Currently, one of the promising ways to improve the cutting process of hard-to-machine materials and quality of parts made from these materials is development and application of combined processing methods, which use additional energy sources to act on the machined material in the cutting zone. A BMSTU-developed cutting method with leading plastic deformation (LPD, which acts to raise the production rate, gain the cutting tool-life, reduce the surface roughness, improve the accuracy of processing and the performance characteristics of products, ensure the reliable flow chip control, and improve the labor conditions, belongs to such sort of methods.One of the most important indicators of processing quality that has a great impact on the operation and cost characteristics of the product and on the machining rate as well is the accuracy of processing. In cutting, the processing errors largely arise from the elastic deformations of a technological system when the cutting force, and, in particular, the radial component of the cutting force, acts on it.The deforming devices, used in cutting with LPD, being located as a rule, on the diametrically opposite side with respect to the cutting zone, act on the technological system as vibration dampers. In addition, as studies have shown, the choice of a rational direction for applying LPD load helps to compensate partially or completely the cutting force radial component effect on the technological

On the Cutting Performance of Segmented Diamond Blades when Dry-Cutting Concrete.

Science.gov (United States)

Sánchez Egea, A J; Martynenko, V; Martínez Krahmer, D; López de Lacalle, L N; Benítez, A; Genovese, G

2018-02-09

The objective of the present study is to analyze and compare the cutting performance of segmented diamond blades when dry-cutting concrete. A cutting criteria is proposed to characterize the wear of the blades by measuring the variation of the external diameter and the weight loss of the blade. The results exhibit the cutting blade SB-A, which has twice the density of diamonds and large contact area, exhibits less wear even though the material removal rate is higher compared with the other two cutting blades. Additionally, the surface topography of the different blades is evaluated to examine the impact of wear depending on the surface profile and the distribution of the diamonds in the blade's matrix. Large number of diamonds pull-out are found in blades type SB-C, which additionally shows the worst wear resistant capability. As a conclusion, the cutting efficiency of the blade is found to be related to the density of embedded diamonds and the type of the surface profile of the cutting blade after reaching the stop criteria.

78 FR 23847 - Drawbridge Operation Regulations; North Carolina Cut, Atlantic Intracoastal Waterway (AIWW...

Science.gov (United States)

2013-04-23

... mile 283.1, over the North Carolina Cut, at Wrightsville Beach, NC has unlimited vertical clearances in.... 12. Energy Effects This action is not a ``significant energy action'' under Executive Order 13211, Actions Concerning Regulations That Significantly Affect Energy Supply, Distribution, or Use. 13...

Casimir effect in a d-dimensional flat spacetime and the cut-off method

International Nuclear Information System (INIS)

Svaiter, N.F.; Svaiter, B.F.

1989-01-01

The CasiMir efeect in a D-dimensional spacetime produced by a Hermitian massless scalar field in the presence of a pair of perfectly reflecting parallel flat plates is discussed. The exponential cut-off regularization method is employed. The regularized vacuum energy and the Casimir energy of this field are evaluated and a detailed analysis of the divergent terms in the regularized vacuum energy is carried out. The two-dimensional version of the Casimir effect is discussed by means of the same cut-off method. A comparison between the above method and the zeta function regularization procedure is presented in a way which gives the unification between these two methods in the present case. (author) [pt

Physical security of cut-and-cover underground facilities

International Nuclear Information System (INIS)

Morse, W.D.

1998-01-01

To aid designers, generic physical security objectives and design concepts for cut-and-cover underground facilities are presented. Specific aspects addressing overburdens, entryways, security doors, facility services, emergency egress, security response force, and human elements are discussed

TEA HF laser with a high specific radiation energy

Science.gov (United States)

Puchikin, A. V.; Andreev, M. V.; Losev, V. F.; Panchenko, Yu. N.

2017-01-01

Results of experimental studies of the chemical HF laser with a non-chain reaction are presented. The possibility of the total laser efficiency of 5 % is shown when a traditional C-to-C pumping circuit with the charging voltage of 20-24 kV is used. It is experimentally shown that the specific radiation output energy of 21 J/l is reached at the specific pump energy of 350 J/l in SF6/H2 = 14/1 mixture at the total pressure of 0.27 bar.

Device for cutting protrusions

Science.gov (United States)

Bzorgi, Fariborz M [Knoxville, TN

2011-07-05

An apparatus for clipping a protrusion of material is provided. The protrusion may, for example, be a bolt head, a nut, a rivet, a weld bead, or a temporary assembly alignment tab protruding from a substrate surface of assembled components. The apparatus typically includes a cleaver having a cleaving edge and a cutting blade having a cutting edge. Generally, a mounting structure configured to confine the cleaver and the cutting blade and permit a range of relative movement between the cleaving edge and the cutting edge is provided. Also typically included is a power device coupled to the cutting blade. The power device is configured to move the cutting edge toward the cleaving edge. In some embodiments the power device is activated by a momentary switch. A retraction device is also generally provided, where the retraction device is configured to move the cutting edge away from the cleaving edge.

Experimental research on the durability cutting tools for cutting-off steel profiles

Directory of Open Access Journals (Sweden)

Cristea Alexandru

2017-01-01

Full Text Available The production lines used for manufacturing U-shaped profiles are very complex and they must have high productivity. One of the most important stages of the fabrication process is the cutting-off. This paper presents the experimental research and analysis of the durability of the cutting tools used for cutting-off U-shaped metal steel profiles. The results of this work can be used to predict the durability of the cutting tools.

Cutting efficiency of a mid-infrared laser on human enamel.

Science.gov (United States)

Levy, G; Koubi, G F; Miserendino, L J

1998-02-01

In this study, the cutting ability of a newly developed dental laser was compared with a dental high-speed handpiece and rotary bur for removal of enamel. Measurements of the volume of tissue removed, energy emitted, and time of exposure were used to quantify the ablation rate (rate of tissue removal) for each test group and compared. Cutting efficiency (mm3/s) of the laser was calculated based on the mean volume of tissue removed per pulse (mm3/pulse) and unit energy expended (mm3/J) over the range of applied powers (2, 4, 6, and 8 W). The specimens were then examined by light microscopy and scanning electron micrographs for qualitative analysis of the amount of remaining debris and the presence of the smear layer on the prepared enamel surface. Calculations of the cutting efficiency of the laser over the range of powers tested revealed a linear relationship with the level of applied power. The maximum average rate of tissue removal by the laser was 0.256 mm3/s at 8 W, compared with 0.945 mm3/s by the dental handpiece. Light microscopy and scanning electron micrograph examinations revealed a reduction in the amount of remaining debris and smear layer in the laser-prepared enamel surfaces, compared with the conventional method. Based on the results of this study, the cutting efficiency of the high-speed handpiece and dental bur was 3.7 times greater than the laser over the range of powers tested, but the laser appeared to create a cleaner enamel surface with minimal thermal damage. Further modifications of the laser system are suggested for improvement of laser cutting efficiency.

Dark energy and key physical parameters of clusters of galaxies

Science.gov (United States)

Bisnovatyi-Kogan, G. S.; Chernin, A. D.

2012-04-01

We study physics of clusters of galaxies embedded in the cosmic dark energy background. Under the assumption that dark energy is described by the cosmological constant, we show that the dynamical effects of dark energy are strong in clusters like the Virgo cluster. Specifically, the key physical parameters of the dark mater halos in clusters are determined by dark energy: (1) the halo cut-off radius is practically, if not exactly, equal to the zero-gravity radius at which the dark matter gravity is balanced by the dark energy antigravity; (2) the halo averaged density is equal to two densities of dark energy; (3) the halo edge (cut-off) density is the dark energy density with a numerical factor of the unity order slightly depending on the halo profile. The cluster gravitational potential well in which the particles of the dark halo (as well as galaxies and intracluster plasma) move is strongly affected by dark energy: the maximum of the potential is located at the zero-gravity radius of the cluster.

Study of Cutting Edge Temperature and Cutting Force of End Mill Tool in High Speed Machining

Directory of Open Access Journals (Sweden)

Kiprawi Mohammad Ashaari

2017-01-01

Full Text Available A wear of cutting tools during machining process is unavoidable due to the presence of frictional forces during removing process of unwanted material of workpiece. It is unavoidable but can be controlled at slower rate if the cutting speed is fixed at certain point in order to achieve optimum cutting conditions. The wear of cutting tools is closely related with the thermal deformations that occurred between the frictional contact point of cutting edge of cutting tool and workpiece. This research paper is focused on determinations of relationship among cutting temperature, cutting speed, cutting forces and radial depth of cutting parameters. The cutting temperature is determined by using the Indium Arsenide (InAs and Indium Antimonide (InSb photocells to measure infrared radiation that are emitted from cutting tools and cutting forces is determined by using dynamometer. The high speed machining process is done by end milling the outer surface of carbon steel. The signal from the photocell is digitally visualized in the digital oscilloscope. Based on the results, the cutting temperature increased as the radial depth and cutting speed increased. The cutting forces increased when radial depth increased but decreased when cutting speed is increased. The setup for calibration and discussion of the experiment will be explained in this paper.

Computed tomography - guided cutting needle biopsy of pulmonary lesions

International Nuclear Information System (INIS)

Liao Shin Yu; Deheinzelin, Daniel; Younes, Riad N.; Chojniak, Rubens

2002-01-01

The purpose of this study was to report the experience of a radiology department in the use of computed tomography-guided cutting needle biopsy of pulmonary nodules, by evaluating diagnostic yield and incidence of complications. This is a retrospective analysis of 52 consecutive patients who underwent lung lesion biopsy guided by computed tomography, performed between May 1997 and May 2000. Thirty-five patients were male and 17 were female, with ages ranging from 5 to 85 years (median, 62 years). The size of the lesions ranged from 1.8 to 15 cm (median, 5.4 cm). In a total of 52 biopsies of lung lesions, 51 biopsies (98.1%) supplied appropriate material for histopathological diagnosis, with 9 diagnosed (17.3%) as benign and 42 (80.8%) as malignant lesions. Specific diagnosis was obtained in 44 (84.6%) biopsies: 4 benign (9.1%) and 40 (90.9%) malignant lesions. The sensitivity, specificity, and accuracy of the cutting needle biopsies for determining presence of malignancy were 96.8%, 100%, and 97.2%, respectively. Complications occurred in 9 cases (17.3%), including 6 cases (11.5%) of small pneumothorax, 1 (1.9%) of hemoptysis, 1 (1.9%) of pulmonary hematoma, and 1 (1.9%) of thoracic wall hematoma. All had spontaneous resolution. There were no complications requiring subsequent intervention. The high sensitivity and specificity of the method and the low rate of complications have established cutting needle biopsy as an efficient and safe tool for the diagnosis of lung lesions. In our hospital, cutting needle biopsy is considered a reliable procedure for the evaluation of indeterminate pulmonary nodules. (author)

Numerical simulation of the shape of laser cut for fiber and CO2 lasers

Science.gov (United States)

Zaitsev, A. V.; Ermolaev, G. V.; Polyanskiy, T. A.; Gurin, A. M.

2017-10-01

The results of numerical modeling of steel plate laser cutting with nitrogen as assist gas with consideration of heat transfer into a bulk material are presented. In this work we studied a distribution of absorbed radiation energy inside cut kerf and the difference between CO2 and fiber laser radiation propagation and absorption. The influence of secondary absorption of reflected from the cut front radiation on stability of melt hydrodynamics is discussed for different laser types.

Improving energy consumption structure: A comprehensive assessment of fossil energy subsidies reform in China

International Nuclear Information System (INIS)

Liu Wei; Li Hong

2011-01-01

Fossil energy subsidies reform would be an effective way to improve the energy consumption structure; however, the reform needs to be assessed comprehensively beforehand as it would exert uncertain impacts on economy, society and environment. In this paper, we use price-gap approach to estimate the fossil energy subsidies of China, then establish CGE model that contains pollutant emissions accounts and CO 2 emissions account to stimulate the fossil energy subsidies reform under different scenarios, and the environmental economic analysis concept is introduced to monetize the pollutant reduction benefits. Furthermore, we analyze the possibility and scope of improving the energy consumption structure from the perspective of technical and economic analysis. Analytical results show that the energy consumption structure could be improved by different extent by removing coal or oil subsidies, while the economic and social indexes will be influenced distinctively. Meanwhile, the effects of cutting coal subsidies are more feasible than that of cutting oil subsidies overall. It is recommended to implement fossil energy subsidies gradually, cut the coal first and then cut oil subsidies successively. - Research highlights: → This paper estimates the scale of fossil energy subsidies of China in 2007 with price-gap approach. → We establish a Social Accounting Matrix and a CGE model extended with pollutant accounts. → We simulate the impacts of removing or cutting subsidies under three different scenarios. → We discuss the possibility and potential of improving energy consumption structure.

The Cutting Process, Chips and Cutting Forces in Machining CFRP

DEFF Research Database (Denmark)

Koplev, A.; Lystrup, Aage; Vorm, T.

1983-01-01

The cutting of unidirectional CFRP, perpendicular as well as parallel to the fibre orientation, is examined. Shaping experiments, ‘quick-stop’ experiments, and a new chip preparation technique are used for the investigation. The formation of the chips, and the quality of the machined surface...... is discussed. The cutting forces parallel and perpendicular to the cutting direction are measured for various parameters, and the results correlated to the formation of chips and the wear of the tool....

Experimental Investigation of Multi-mode Fiber Laser Cutting of Cement Mortar

Science.gov (United States)

2018-01-01

This study successfully applied multi-mode laser cutting with the variation of the laser cutting speed to cement mortar for the first time. The effects of the amount of silica sand in the cement mortar on laser cutting are tested and analyzed. The kerf width and penetration depth of the specimens after laser cutting are investigated. As the laser cutting speed increases, the penetration depth decreases for both cement paste and cement mortar, whereas the kerf width becomes saturated and increases, respectively, for cement paste and cement mortar. Cross sections of the specimens are compared with illustrations. Top-view images of the cement mortar with indicators of the physical characteristics, such as re-solidification, burning, and cracks are examined, and the possible causes of these characteristics are explained. The optical absorption rates of cement-based materials are quantified at wide ranges of wavelength to compare the absorption rates in accordance with the materials compositions. The chemical composition variation before and after laser cutting is also compared by EDX (Energy Dispersive X-Ray) analysis. In addition to these observations, material removal mechanisms for cement mortar are proposed. PMID:29439431

Experimental Investigation of Multi-mode Fiber Laser Cutting of Cement Mortar.

Science.gov (United States)

Lee, Dongkyoung; Pyo, Sukhoon

2018-02-10

This study successfully applied multi-mode laser cutting with the variation of the laser cutting speed to cement mortar for the first time. The effects of the amount of silica sand in the cement mortar on laser cutting are tested and analyzed. The kerf width and penetration depth of the specimens after laser cutting are investigated. As the laser cutting speed increases, the penetration depth decreases for both cement paste and cement mortar, whereas the kerf width becomes saturated and increases, respectively, for cement paste and cement mortar. Cross sections of the specimens are compared with illustrations. Top-view images of the cement mortar with indicators of the physical characteristics, such as re-solidification, burning, and cracks are examined, and the possible causes of these characteristics are explained. The optical absorption rates of cement-based materials are quantified at wide ranges of wavelength to compare the absorption rates in accordance with the materials compositions. The chemical composition variation before and after laser cutting is also compared by EDX (Energy Dispersive X-Ray) analysis. In addition to these observations, material removal mechanisms for cement mortar are proposed.

Analysis of changes in paper cutting forces during the cutting cycle in single-knife guillotine

OpenAIRE

Rusin, Agnieszka; Petriaszwili, Georgij

2013-01-01

Paper presents the results of changes in the three components of cutting forces of paper stacks cutting during the cutting cycle in single-knife guillotine. The changes of the three components of cutting force at different stages of cutting cycle were analyzed.

Specificity and affinity quantification of flexible recognition from underlying energy landscape topography.

Directory of Open Access Journals (Sweden)

Xiakun Chu

2014-08-01

Full Text Available Flexibility in biomolecular recognition is essential and critical for many cellular activities. Flexible recognition often leads to moderate affinity but high specificity, in contradiction with the conventional wisdom that high affinity and high specificity are coupled. Furthermore, quantitative understanding of the role of flexibility in biomolecular recognition is still challenging. Here, we meet the challenge by quantifying the intrinsic biomolecular recognition energy landscapes with and without flexibility through the underlying density of states. We quantified the thermodynamic intrinsic specificity by the topography of the intrinsic binding energy landscape and the kinetic specificity by association rate. We found that the thermodynamic and kinetic specificity are strongly correlated. Furthermore, we found that flexibility decreases binding affinity on one hand, but increases binding specificity on the other hand, and the decreasing or increasing proportion of affinity and specificity are strongly correlated with the degree of flexibility. This shows more (less flexibility leads to weaker (stronger coupling between affinity and specificity. Our work provides a theoretical foundation and quantitative explanation of the previous qualitative studies on the relationship among flexibility, affinity and specificity. In addition, we found that the folding energy landscapes are more funneled with binding, indicating that binding helps folding during the recognition. Finally, we demonstrated that the whole binding-folding energy landscapes can be integrated by the rigid binding and isolated folding energy landscapes under weak flexibility. Our results provide a novel way to quantify the affinity and specificity in flexible biomolecular recognition.

Broadband Ce(III)-Sensitized Quantum Cutting in Core-Shell Nanoparticles: Mechanistic Investigation and Photovoltaic Application.

Science.gov (United States)

Sun, Tianying; Chen, Xian; Jin, Limin; Li, Ho-Wa; Chen, Bing; Fan, Bo; Moine, Bernard; Qiao, Xvsheng; Fan, Xianping; Tsang, Sai-Wing; Yu, Siu Fung; Wang, Feng

2017-10-19

Quantum cutting in lanthanide-doped luminescent materials is promising for applications such as solar cells, mercury-free lamps, and plasma panel displays because of the ability to emit multiple photons for each absorbed higher-energy photon. Herein, a broadband Ce 3+ -sensitized quantum cutting process in Nd 3+ ions is reported though gadolinium sublattice-mediated energy migration in a NaGdF 4 :Ce@NaGdF 4 :Nd@NaYF 4 nanostructure. The Nd 3+ ions show downconversion of one ultraviolet photon through two successive energy transitions, resulting in one visible photon and one near-infrared (NIR) photon. A class of NaGdF 4 :Ce@NaGdF 4 :Nd/Yb@NaYF 4 nanoparticles is further developed to expand the spectrum of quantum cutting in the NIR. When the quantum cutting nanoparticles are incorporated into a hybrid crystalline silicon (c-Si) solar cell, a 1.2-fold increase in short-circuit current and a 1.4-fold increase in power conversion efficiency is demonstrated under short-wavelength ultraviolet irradiation. These insights should enhance our ability to control and utilize spectral downconversion with lanthanide ions.

Lucky Motifs in Chinese Folk Art: Interpreting Paper-cut from Chinese Shaanxi

Directory of Open Access Journals (Sweden)

Xuxiao WANG

2013-11-01

Full Text Available Paper-cut is not simply a form of traditional Chinese folk art. Lucky motifs developed in paper-cut certainly acquired profound cultural connotations. As paper-cut is a time-honoured skill across the nation, interpreting those motifs requires cultural receptiveness and anthropological sensitivity. The author of this article analyzes examples of paper-cut from Northern Shaanxi, China, to identify the cohesive motifs and explore the auspiciousness of the specific concepts of Fu, Lu, Shou, Xi. The paper-cut of Northern Shaanxi is an ideal representative of the craft as a whole because of the relative stability of this region in history, in terms of both art and culture. Furthermore, its straightforward style provides a clear demonstration of motifs regarding folk understanding of expectations for life.

Structural and compositional characterization of X-cut LiNbO3 crystals implanted with high energy oxygen and carbon ions

International Nuclear Information System (INIS)

Bentini, G.G.; Bianconi, M.; Cerutti, A.; Chiarini, M.; Pennestri, G.; Sada, C.; Argiolas, N.; Bazzan, M.; Mazzoldi, P.; Guzzi, R.

2005-01-01

High energy implantation of medium-light elements such as oxygen and carbon was performed in X-cut LiNbO 3 single crystals in order to prepare high quality optical waveguides. The compositional and damage profiles, obtained by exploiting the secondary ion mass spectrometry and Rutherford back-scattering techniques respectively, were correlated to the structural properties measured by the high resolution X-ray diffraction. This study evidences the development of tensile strain induced by the ion implantation that can contribute to the decrease of the ordinary refractive index variation through the photo-elastic effect

Cutting and Self-Harm

Science.gov (United States)

... Your feelings Feeling sad Cutting and self-harm Cutting and self-harm Self-harm, sometimes called self- ... There are many types of self-injury, and cutting is one type that you may have heard ...

The cutting of cocaine and heroin: A critical review.

Science.gov (United States)

Broséus, Julian; Gentile, Natacha; Esseiva, Pierre

2016-05-01

The illicit drug cutting represents a complex problem that requires the sharing of knowledge from addiction studies, toxicology, criminology and criminalistics. Therefore, cutting is not well known by the forensic community. Thus, this review aims at deciphering the different aspects of cutting, by gathering information mainly from criminology and criminalistics. It tackles essentially specificities of cocaine and heroin cutting. The article presents the detected cutting agents (adulterants and diluents), their evolution in time and space and the analytical methodology implemented by forensic laboratories. Furthermore, it discusses when, in the history of the illicit drug, cutting may take place. Moreover, researches studying how much cutting occurs in the country of destination are analysed. Lastly, the reasons for cutting are addressed. According to the literature, adulterants are added during production of the illicit drug or at a relatively high level of its distribution chain (e.g. before the product arrives in the country of destination or just after its importation in the latter). Their addition seems hardly justified by the only desire to increase profits or to harm consumers' health. Instead, adulteration would be performed to enhance or to mimic the illicit drug effects or to facilitate administration of the drug. Nowadays, caffeine, diltiazem, hydroxyzine, levamisole, lidocaïne and phenacetin are frequently detected in cocaine specimens, while paracetamol and caffeine are almost exclusively identified in heroin specimens. This may reveal differences in the respective structures of production and/or distribution of cocaine and heroin. As the relevant information about cutting is spread across different scientific fields, a close collaboration should be set up to collect essential and unified data to improve knowledge and provide information for monitoring, control and harm reduction purposes. More research, on several areas of investigation, should be

Energy analysis of various grassland utilisation systems

Directory of Open Access Journals (Sweden)

Jozef Ržonca

2005-01-01

Full Text Available In 2003 and 2004 was carried out the energy analysis of the different types of permanent grassland utilization on the Hrubý Jeseník locality. There were estimated values of the particular entrances of additional energy. Energy entrances moved according to the pratotechnologies from 2.17 GJ. ha–1 to 22.70 GJ.ha–1. The biggest share on energy entrances had fertilizers. It was 84.93% by the nitrogen fertilisation. The most energy benefit of brutto and nettoenergy was marked by the low intensive utilisation (33.40 GJ.ha–1 NEL and 32.40 GJ.ha–1 NEV on average. The highest value of energy efficiency (13.23% was marked by the low intensive utilization of permanent grassland. By using of higher doses of industrial fertilizers has energy efficiency decreased. From view of energy benefit and intensiveness on energy entrances it appears the most available utilisation of permanent grassland with three cuts per year (first cut on May 31st at the latest, every next after 60 days or two cuts per year (first cut on July 15th, next cuts after 90 days.

On Permuting Cut with Contraction

OpenAIRE

Borisavljevic, Mirjana; Dosen, Kosta; Petric, Zoran

1999-01-01

The paper presents a cut-elimination procedure for intuitionistic propositional logic in which cut is eliminated directly, without introducing the multiple-cut rule mix, and in which pushing cut above contraction is one of the reduction steps. The presentation of this procedure is preceded by an analysis of Gentzen's mix-elimination procedure, made in the perspective of permuting cut with contraction. It is also shown that in the absence of implication, pushing cut above contraction doesn't p...

Cutting method for structural component into block like shape, and device used for cutting

International Nuclear Information System (INIS)

Nakazawa, Koichi; Ito, Akira; Tateiwa, Masaaki.

1995-01-01

Two grooves each of a predetermined depth are formed along a surface of a structural component, and a portion between the two grooves is cut in the direction of the depth from the surface of the structural component by using a cutting wire of a wire saw device. Then, the cutting wire is moved in the extending direction of the grooves while optionally changing the position in the direction of the depth to conduct cutting for the back face. Further, the cutting wire is moved in the direction of the depth of the groove toward the surface, to cut a portion between the two grooves. The wire saw device comprises a wire saw main body movable along the surface of the structural component, a pair of wire guide portions extending in the direction of the depth, guide pooleys capable of guiding the cutting wire guides revolvably and rotatably disposed at the top end, and an endless annular cutting wire extending between the wire guide portions. Thus, it is possible to continuously cut out blocks set to optional size and thickness. In addition, remote cutting is possible with no requirement for an operator to access to the vicinity of radioactivated portions. (N.H.)

An FMS Dynamic Production Scheduling Algorithm Considering Cutting Tool Failure and Cutting Tool Life

International Nuclear Information System (INIS)

Setiawan, A; Wangsaputra, R; Halim, A H; Martawirya, Y Y

2016-01-01

This paper deals with Flexible Manufacturing System (FMS) production rescheduling due to unavailability of cutting tools caused either of cutting tool failure or life time limit. The FMS consists of parallel identical machines integrated with an automatic material handling system and it runs fully automatically. Each machine has a same cutting tool configuration that consists of different geometrical cutting tool types on each tool magazine. The job usually takes two stages. Each stage has sequential operations allocated to machines considering the cutting tool life. In the real situation, the cutting tool can fail before the cutting tool life is reached. The objective in this paper is to develop a dynamic scheduling algorithm when a cutting tool is broken during unmanned and a rescheduling needed. The algorithm consists of four steps. The first step is generating initial schedule, the second step is determination the cutting tool failure time, the third step is determination of system status at cutting tool failure time and the fourth step is the rescheduling for unfinished jobs. The approaches to solve the problem are complete-reactive scheduling and robust-proactive scheduling. The new schedules result differences starting time and completion time of each operations from the initial schedule. (paper)

Plant Hormone Homeostasis, Signaling, and Function during Adventitious Root Formation in Cuttings.

Science.gov (United States)

Druege, Uwe; Franken, Philipp; Hajirezaei, Mohammad R

2016-01-01

Adventitious root (AR) formation in cuttings is a multiphase developmental process, resulting from wounding at the cutting site and isolation from the resource and signal network of the whole plant. Though, promotive effects of auxins are widely used for clonal plant propagation, the regulation and function of plant hormones and their intricate signaling networks during AR formation in cuttings are poorly understood. In this focused review, we discuss our recent publications on the involvement of polar auxin transport (PAT) and transcriptional regulation of auxin and ethylene action during AR formation in petunia cuttings in a broad context. Integrating new findings on cuttings of other plant species and general models on plant hormone networks, a model on the regulation and function of auxin, ethylene, and jasmonate in AR formation of cuttings is presented. PAT and cutting off from the basipetal auxin drain are considered as initial principles generating early accumulation of IAA in the rooting zone. This is expected to trigger a self-regulatory process of auxin canalization and maximization to responding target cells, there inducing the program of AR formation. Regulation of auxin homeostasis via auxin influx and efflux carriers, GH3 proteins and peroxidases, of flavonoid metabolism, and of auxin signaling via AUX/IAA proteins, TOPLESS, ARFs, and SAUR-like proteins are postulated as key processes determining the different phases of AR formation. NO and H2O2 mediate auxin signaling via the cGMP and MAPK cascades. Transcription factors of the GRAS-, AP2/ERF-, and WOX-families link auxin signaling to cell fate specification. Cyclin-mediated governing of the cell cycle, modifications of sugar metabolism and microtubule and cell wall remodeling are considered as important implementation processes of auxin function. Induced by the initial wounding and other abiotic stress factors, up-regulation of ethylene biosynthesis, and signaling via ERFs and early accumulation of

Plant hormone homeostasis, signaling and function during adventitious root formation in cuttings

Directory of Open Access Journals (Sweden)

Uwe eDruege

2016-03-01

Full Text Available Adventitious root (AR formation in cuttings is a multiphase developmental process, resulting from wounding at the cutting site and isolation from the resource and signal network of the whole plant. Though promotive effects of auxins are widely used for clonal plant propagation, the regulation and function of plant hormones and their intricate signaling networks during AR formation in cuttings are poorly understood. In this focused review, we discuss our recent publications on the involvement of polar auxin transport (PAT and transcriptional regulation of auxin and ethylene action during AR formation in petunia cuttings in a broad context. Integrating new findings on cuttings of other plant species and general models on plant hormone networks, a model on the regulation and function of auxin, ethylene and jasmonate in AR formation of cuttings is presented. PAT and cutting off from the basipetal auxin drain are considered as initial principles generating early accumulation of IAA in the rooting zone. This is expected to trigger a self-regulatory process of auxin canalization and maximization to responding target cells, there inducing the program of AR formation. Regulation of auxin homeostasis via auxin influx and efflux carriers, GH3 proteins and peroxidases, of flavonoid metabolism and of auxin signaling via AUX/IAA proteins, TOPLESS, ARFs and SAUR-like proteins are postulated as key processes determining the different phases of AR formation. NO and H2O2 mediate auxin signaling via the cGMP and MAPK cascades. Transcription factors of the GRAS-, AP2/ERF- and WOX-families link auxin signaling to cell fate specification. Cyclin-mediated governing of the cell cycle, modifications of sugar metabolism and microtubule and cell wall remodeling are considered as important implementation processes of auxin function. Induced by the initial wounding and other abiotic stress factors, up-regulation of ethylene biosynthesis and signaling via ERFs and early

Self-contained pipe cutting shear. Innovative technology summary report

International Nuclear Information System (INIS)

1998-11-01

The US Department of Energy (DO) is in the process of decontaminating and decommissioning (D and D) many of its nuclear facilities throughout the country. Facilities have to be dismantled and demolition waste must be sized into manageable pieces for handling and disposal. Typically, the facilities undergoing D and D are contaminated, either chemically, radiologically, or both. In its D and D work, the DOE was in need of a tool capable of cutting steel and stainless steel pipe up to 6.4 cm in diameter. The self-contained pipe cutting shear was developed by Lukas Hydraulic GmbH and Co. KG to cut pipes up to 6.4 cm (2.5 in.) in diameter. This tool is a portable, hand-held hydraulic shear that is powered by a built-in rechargeable battery or a portable auxiliary rechargeable battery. Adding to its portability, it contains no hydraulic fluid lines or electrical cords, making it useful in congested areas or in areas with no power. Both curved and straight blades can be attached, making it adaptable to a variety of conditions. This tool is easy to set up, operates quietly, and cuts through pipes quickly. It is especially useful on contaminated pipes, as it crimps the ends while cutting and produces no residual cuttings. This shear is a valuable alternative to baseline technologies such as portable band saws, electric hacksaws, and other hydraulic shears. Costs using the innovative shear for cutting 2.5 cm (1-in.) pipe, for example, are comparable to costs using a conventional shear, approximately 80% of portable bandsaw costs and half of electric hacksaw costs

Slice-push, formation of grooves and the scale effect in cutting.

Science.gov (United States)

Atkins, A G

2016-06-06

Three separate aspects of cutting are investigated which complement other papers on the mechanics of separation processes presented at this interdisciplinary Theo Murphy meeting. They apply in all types of cutting whether blades are sharp or blunt, and whether the material being cut is 'hard, stiff and strong' or 'soft, compliant and weak'. The first topic discusses why it is easier to cut when there is motion along (parallel to) the blade as well motion across (perpendicular to) the cutting edge, and the analysis is applied to optimization of blade geometries to produce minimum cutting forces and hence minimum damage to cut surfaces. The second topic concerns cutting with more than one edge with particular application to the formation of grooves in surfaces by hard pointed tools. The mechanics are investigated and applied to the topic of abrasive wear by hard particles. Traditional analyses say that abrasive wear resistance increases monotonically with the hardness of the workpiece, but we show that the fracture toughness of the surface material is also important, and that behaviour is determined by the toughness-to-hardness ratio rather than hardness alone. Scaling forms the third subject. As cutting is a branch of elasto-plastic fracture mechanics, cube-square energy scaling applies in which the important length scale is (ER/k (2)), where E is Young's modulus, R is the fracture toughness and k is the shear yield strength. Whether, in cutting, material is removed as ductile ribbons, as semi-ductile discontinuous chips, or by brittle 'knocking lumps out' is shown to depend on the depth of cut relative to this characteristic length parameter. Scaling in biology is called allometry and its relationship with engineering scaling is discussed. Some speculative predictions are made in relation to the action of teeth on food.

Advanced cutting techniques: laser and fissuration cutting

International Nuclear Information System (INIS)

Migliorati, B.; Gay, P.

1984-01-01

Experimental tests have been performed using CO 2 laser with output power 1 to 15 kW to evaluate the effect of varying the following parameters: material (carbon steel Fe 42 C, stainless steel AISI 304, concrete), laser power, beam characteristics, work piece velocity, gas type and distribution on the laser interaction zone. In the case of concrete, drilling depths of 80 mm were obtained in a few seconds using a 10 kW laser beam. Moreover pieces of 160 mm were cut at 0.01 meters per minute. Results with carbon steel indicated maximum thicknesses of 110 mm, cut at 0.01 meters per minute with 10 kW, depths about 20% lower were obtained with the AISI 304 stainless steel. A parallel investigation was aimed at characterizing particulate emission during the laser cutting process. At the end of the research it was possible to elaborate a preliminary proposal concerning a laser based dismantling system for the application to a typical Nuclear Power Station. (author)

Cutting agents for special metals

International Nuclear Information System (INIS)

Sugito, Seiji; Sakakibara, Fumi

1979-01-01

The quantity of use of special metals has increased year after year in the Plasma Research Institute, Nagoya University, with the development of researches on plasma and nuclear fusion. Most of these special metals are hard to cut, and in order to secure the surface smoothness and dimensional accuracy, considerable efforts are required. The method of experiment is as follows: cutting agents salt water and acetone, rape-seed oil, sulfide and chloride oil and water soluble cutting oil W grade 3; metals to be cut niobium, molybdenum, tantalum, titanium and tungsten; cutting conditions cutting speed 4.7 to 90 m/min, feed 0.07 to 0.2 mm/rev, depth of cut 0.1 to 0.4 mm, tool cemented carbide bit. Chemicals such as tetrachloromethane and trichloroethane give excellent cutting performance, but the toxicity is intense and the stimulative odor exists, accordingly they are hard to use practically. Cutting was easier when the salt water added with acetone was used than the case of rape-seed oil, but salt water is corrosive. Recently, the machining of molybdenum has been often carried out, and the water soluble cutting oil was the best. It is also good for cutting stainless steel, and its lubricating property is improved by adding some additives such as sulfur, chlorine, phosphorus and molybdenum disulfide. However after cutting with it, washing is required. (Kako, I.)

Bone cutting capacity and osseointegration of surface-treated orthodontic mini-implants.

Science.gov (United States)

Kim, Ho-Young; Kim, Sang-Cheol

2016-11-01

The objective of the study was to evaluate the practicality and the validity of different surface treatments of self-drilling orthodontic mini-implants (OMIs) by comparing bone cutting capacity and osseointegration. Self-drilling OMIs were surface-treated in three ways: Acid etched (Etched), resorbable blasting media (RBM), partially resorbabla balsting media (Hybrid). We compared the bone cutting capacity by measuring insertion depths into artificial bone (polyurethane foam). To compare osseointegration, OMIs were placed in the tibia of 25 rabbits and the removal torque value was measured at 1, 2, 4, and 8 weeks after placement. The specimens were analyzed by optical microscopy, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). The bone cutting capacity of the etched and hybrid group was lower than the machined (control) group, and was most inhibited in the RBM group ( p drilling OMIs, without a corresponding reduction in bone cutting capacity.

Performance Testing of Cutting Fluids

DEFF Research Database (Denmark)

Belluco, Walter

The importance of cutting fluid performance testing has increased with documentation requirements of new cutting fluid formulations based on more sustainable products, as well as cutting with minimum quantity of lubrication and dry cutting. Two sub-problems have to be solved: i) which machining...... tests feature repeatability, reproducibility and sensitivity to cutting fluids, and ii) to what extent results of one test ensure relevance to a wider set of machining situations. The present work is aimed at assessing the range of validity of the different testing methods, investigating correlation...... within the whole range of operations, materials, cutting fluids, operating conditions, etc. Cutting fluid performance was evaluated in turning, drilling, reaming and tapping, and with respect to tool life, cutting forces, chip formation and product quality (dimensional accuracy and surface integrity...

Effect of tube diameter on the specific energy consumption of the ice making process

International Nuclear Information System (INIS)

Tangthieng, C.

2011-01-01

One of the favorite forms of ice for consuming is tube ice, which is produced by a refrigeration unit referred to as an ice making tower. In order to redesign the tower for the energy-efficiency purpose, the aim of this paper is to numerically investigate the effect of tube diameter on the ice thickness, the cooling load, and the specific energy consumption. The mathematical model of the ice formation within the tube is developed by assuming unsteady and one-dimensional heat conduction. The governing equations are composed of the wall and the ice regions with the convective boundary condition and isothermal solidification at the interface. The governing system is transformed into a dimensionless form and numerically solved by the finite difference method. The numerical results are validated by comparing the ice thickness obtained from the numerical prediction and that obtained from the field measurement, resulting in qualitative agreement. The variations of ice thickness, cooling load, and specific energy consumption with time for four different tube diameters are presented. The result shows the location of the minimum specific energy consumption as a function of time. By comparing between different tube diameters, the value of the minimum specific energy consumption of a small diameter tube is lower than that of a large diameter one. On the other hand, the behavior of the specific energy consumption of a large diameter tube indicates the existence of a low specific energy consumption period of time beyond the minimum point. Therefore, by choosing a proper tube diameter, the minimum value of the average specific energy consumption over the entire production cycle is obtained, leading to higher energy efficiency. - Research Highlights: → The result indicates the minimum specific energy consumption as a function of time. → A smaller diameter tube has a lower value of the minimum specific energy consumption, but a large one has an extended range of low specific

Photomask specifications for high energy physics detectors

CERN Document Server

Pindo, M

2002-01-01

Planar technologies used for radiation detector fabrication imply an extensive use of photomasks whose characteristics are critical in determining final detector performance. Compatibly with their manufacturing process, photomasks must satisfy the application-specific requirements dictated both by wafer manufacturers and detector final users. The design and realization of microstrip and pixel detectors, widely used in high energy physics experiments, ask for intensive scientific effort, advanced technology and important economical investments. Photomask specification definition is one of the fundamental steps to optimize detector fabrication processes and fulfill experimental requirements at the most appropriate cost.

Logging costs and cutting methods in young-growth ponderosa pine in California

Science.gov (United States)

Philip M. McDonald; William A. Atkinson; Dale O. Hall

1969-01-01

Mixed-conifer stands at the Challenge Experimental Forest, Calif., were cut to four specifications: seed-tree, group selection, single tree selection, and clearcut. Logging costs and production rates were compared and evaluated. Cutting method had little effect on felling or skidding production; felling ranged from 1,802 to 2,019 bd ft per hour, and skidding from 3,138...

Cutting and coagulation during intraoral soft tissue surgery using Er: YAG laser.

Science.gov (United States)

Onisor, I; Pecie, R; Chaskelis, I; Krejci, I

2013-06-01

To find the optimal techniques and parameters that enables Er:YAG laser to be used successfully for small intraoral soft tissue interventions, in respect to its cutting and coagulation abilities. In vitro pre-tests: 4 different Er:YAG laser units and one CO2 unit as the control were used for incision and coagulation on porcine lower jaws and optimal parameters were established for each type of intervention and each laser unit: energy, frequency, type, pulse duration and distance. 3 different types of intervention using Er:YAG units are presented: crown lengthening, gingivoplasty and maxillary labial frenectomy with parameters found in the in vitro pre-tests. The results showed a great decrease of the EMG activity of masseter and anterior temporalis muscles. Moreover, the height and width of the chewing cycles in the frontal plane increased after therapy. Er:YAG is able to provide good cutting and coagulation effects on soft tissues. Specific parameters have to be defined for each laser unit in order to obtain the desired effect. Reduced or absent water spray, defocused light beam, local anaesthesia and the most effective use of long pulses are methods to obtain optimal coagulation and bleeding control.

Female genital cutting.

Science.gov (United States)

Perron, Liette; Senikas, Vyta; Burnett, Margaret; Davis, Victoria

2013-11-01

To strengthen the national framework for care of adolescents and women affected by female genital cutting (FGC) in Canada by providing health care professionals with: (1) information intended to strengthen their knowledge and understanding of the practice; (2) directions with regard to the legal issues related to the practice; (3) clinical guidelines for the management of obstetric and gynaecological care, including FGC related complications; and (4) guidance on the provision of culturally competent care to adolescents and women with FGC. Published literature was retrieved through searches of PubMed, CINAHL, and The Cochrane Library in September 2010 using appropriate controlled vocabulary (e.g., Circumcision, Female) and keywords (e.g., female genital mutilation, clitoridectomy, infibulation). We also searched Social Science Abstracts, Sociological Abstracts, Gender Studies Database, and ProQuest Dissertations and Theses in 2010 and 2011. There were no date or language restrictions. Searches were updated on a regular basis and incorporated in the guideline to December 2011. Grey (unpublished) literature was identified through searching the websites of health technology assessment and health technology-related agencies, clinical practice guideline collections, clinical trial registries, and national and international medical specialty societies. The quality of evidence in this document was rated using the criteria described in the Report of the Canadian Task Force on Preventive Health Care (Table 1). Summary Statements 1. Female genital cutting is internationally recognized as a harmful practice and a violation of girls' and women's rights to life, physical integrity, and health. (II-3) 2. The immediate and long-term health risks and complications of female genital cutting can be serious and life threatening. (II-3) 3. Female genital cutting continues to be practised in many countries, particularly in sub-Saharan Africa, Egypt, and Sudan. (II-3) 4. Global migration

Remotely controlled cutting techniques in the field of nuclear decommissioning. Overview of effectively applied thermal cutting methods

International Nuclear Information System (INIS)

Bienia, H.; Klotz, B.

2008-01-01

This article describes 3 thermal cutting technologies that are effectively used in nuclear decommissioning projects: the autonomous flame cutting, the plasma arc cutting and the contact arc metal cutting. The autonomous flame cutting technology is based on a high pressure oxygen jet oxidizing the material in a small kerf. Not all metal types are appropriate for this technology. The plasma arc cutting, in contrast to the previous technology, uses an electronically induced plasma arc to melt a kerf in the material. Inside the plasma arc temperatures up to 30.000 K exist, so in theory, this temperature is sufficient to cut all materials. Contact arc metal cutting is a new thermal cutting technology for under-water cutting works. Here, a carbon blade cuts the components. An electric arc between the cutting blade and component melts a kerf into the material easing the cutting. This technology allows the cutting of complex structures with hollows. The applications in nuclear facility dismantling of these 3 cutting technologies and their limits are reported and their requirements (staff, investment) listed in a table. (A.C.)

Concept for Specific Lines of Business, Energy Saving Tourism

International Nuclear Information System (INIS)

Jilek, W.

1998-01-01

In the spirit of the objectives of the Energy Plan 1995 in order to make more efficient use of energy and thus to reduce energy requirements, to promote the use of renewable energies, and to attach maximum importance to the ecological compatibility of the energy systems, among other project the provincial government of Styria is pursuing the option of consulting small and medium-sized enterprises in a target manner. Three years after being launched, this Ecological Company Consulting scheme for various lines of business is now producing successful results, demonstrating that energy saving, business profit and ecology can go hand in hand by example of numerous pilot projects. Trade-specific concepts have been elaborated for foodstuffs, carpenters and car repair and sales firms, bakeries and hairdressers and, most recently, for tourist industry business /hotels, bars, restaurants, etc.). The province of Styria, represented by the Energy Commissioner and the department of waste management, is co-operating closely in the Ecological Company Consulting scheme with the Styrian Chamber of Commerce and the Economy Promotion Institute (Wirtschaftsfoerderungsinstitut). In several cases, other provinces, the Federal Ministry of Environmental, Youth and Family Affairs, and the Federal Chamber of Commerce have adopted the results of this co-operation, while in some cases subsidy schemes are linked to these trade-specific concepts. In the course of the scheme, the aim is to investigate energy requirements, saving potentials and questions of waste management. (author)

New Nanostructured Li 2 S/Silicon Rechargeable Battery with High Specific Energy

KAUST Repository

Yang, Yuan; McDowell, Matthew T.; Jackson, Ariel; Cha, Judy J.; Hong, Seung Sae; Cui, Yi

2010-01-01

Rechargeable lithium ion batteries are important energy storage devices; however, the specific energy of existing lithium ion batteries is still insufficient for many applications due to the limited specific charge capacity of the electrode

Optimization of CO2 laser cutting parameters on Austenitic type Stainless steel sheet

Science.gov (United States)

Parthiban, A.; Sathish, S.; Chandrasekaran, M.; Ravikumar, R.

2017-03-01

Thin AISI 316L stainless steel sheet widely used in sheet metal processing industries for specific applications. CO2 laser cutting is one of the most popular sheet metal cutting processes for cutting of sheets in different profile. In present work various cutting parameters such as laser power (2000 watts-4000 watts), cutting speed (3500mm/min - 5500 mm/min) and assist gas pressure (0.7 Mpa-0.9Mpa) for cutting of AISI 316L 2mm thickness stainless sheet. This experimentation was conducted based on Box-Behenken design. The aim of this work is to develop a mathematical model kerf width for straight and curved profile through response surface methodology. The developed mathematical models for straight and curved profile have been compared. The Quadratic models have the best agreement with experimental data, and also the shape of the profile a substantial role in achieving to minimize the kerf width. Finally the numerical optimization technique has been used to find out best optimum laser cutting parameter for both straight and curved profile cut.

Optimizing cutting conditions on sustainable machining of aluminum alloy to minimize power consumption

Science.gov (United States)

Nur, Rusdi; Suyuti, Muhammad Arsyad; Susanto, Tri Agus

2017-06-01

Aluminum is widely utilized in the industrial sector. There are several advantages of aluminum, i.e. good flexibility and formability, high corrosion resistance and electrical conductivity, and high heat. Despite of these characteristics, however, pure aluminum is rarely used because of its lacks of strength. Thus, most of the aluminum used in the industrial sectors was in the form of alloy form. Sustainable machining can be considered to link with the transformation of input materials and energy/power demand into finished goods. Machining processes are responsible for environmental effects accepting to their power consumption. The cutting conditions have been optimized to minimize the cutting power, which is the power consumed for cutting. This paper presents an experimental study of sustainable machining of Al-11%Si base alloy that was operated without any cooling system to assess the capacity in reducing power consumption. The cutting force was measured and the cutting power was calculated. Both of cutting force and cutting power were analyzed and modeled by using the central composite design (CCD). The result of this study indicated that the cutting speed has an effect on machining performance and that optimum cutting conditions have to be determined, while sustainable machining can be followed in terms of minimizing power consumption and cutting force. The model developed from this study can be used for evaluation process and optimization to determine optimal cutting conditions for the performance of the whole process.

Building Partnerships to Cut Petroleum Use in Transportation (Brochure)

Energy Technology Data Exchange (ETDEWEB)

None, None

2014-02-01

The U.S. Department of Energy's Clean Cities initiative advances the nation's economic, environmental, and energy security by supporting local actions to cut petroleum use in transportation. Clean Cities accomplishes this work through the activities of nearly 100 local coalitions. These coalitions provide resources and technical assistance in the deployment of alternative and renewable fuels, idle-reduction measures, fuel economy improvements, and new transportation technologies as they emerge.

Extension without Cut

OpenAIRE

Straßburger , Lutz

2012-01-01

International audience; In proof theory one distinguishes sequent proofs with cut and cut-free sequent proofs, while for proof complexity one distinguishes Frege-systems and extended Frege-systems. In this paper we show how deep inference can provide a uniform treatment for both classifications, such that we can define cut-free systems with extension, which is neither possible with Frege-systems, nor with the sequent calculus. We show that the propositional pigeon-hole principle admits polyno...

Disjunctive cuts in a branch-and-price algorithm for the capacitated vehicle routing problem

DEFF Research Database (Denmark)

Røpke, Stefan

This talk presents computational results that show the usefulness of the general-purpose valid inequalities disjunctive cuts when applied to the CVRP. Results indicate that the disjunctive cuts are able to reduce the gap between lower bound and upper bound more than state-of-the-art problem...... specific inequalities. Results also indicate that introducing the cuts leads to a smaller branch and bound tree and faster solution times overall....

Lifetime information from correlation functions selected by directional cuts

International Nuclear Information System (INIS)

Gelbke, C.K.

1995-01-01

Two-particle correlation functions provide information on the space-time characteristics of the emitting source. In many cases, ambiguities of the relative magnitudes of source radius and lifetime can be reduced by analysis of correlation functions evaluated for specific directional cuts on the relative velocity of the coincident particle pair. Information on non-spherical breakup geometries is more difficult to extract. Examples of two-proton correlation functions in which directional cuts are employed to reduce existing space-time ambiguities for the emitting system are presented. (author). 50 refs., 10 figs

Accuracy of the WHO’s body mass index cut-off points to measure gender- and age-specific obesity in middle-aged adults living in the city of Rio de Janeiro, Brazil

Directory of Open Access Journals (Sweden)

Wollner Materko

2017-09-01

Full Text Available Introduction. Obesity is defined by the World Health Organization (WHO as a disease characterized by the excessive accumulation of body fat. Obesity is considered a public health problem, leading to serious social, psychological and physical problems. However, the appropriate cut-off point of body mass index (BMI based on body fat percentage (BF% for classifying an individual as obese in middle-aged adults living in Rio de Janeiro remains unclear. Materials and methods. This was a prospective cross-sectional study comprising of 856 adults (413 men and 443 women living in Rio de Janeiro, Brazil ranging from 30-59 years of age. The data were collected over a two year period (2010-2011, and all participants were underwent anthropometric evaluation. The gold standard was the percentage of body fat estimated by bioelectrical impedance analysis. The optimal sensitivity and specificity were attained by adjusting BMI cut-off values to predict obesity based on the WHO criteria: BF% >25% in men and >35% in women, according to the receiver operating characteristic curve (ROC analysis adjusted for age and for the whole group.Results. The BMI cut-offs for predicting BF% were 29.9 kg/m2 in men and 24.9 kg/m2 in women. Conclusions. The BMI that corresponded to a BF% previously defining obesity was similar to that of other Western populations for men but not for women. Furthermore, gender and age specific cut-off values are recommended in this population.

Calibration and comparison of accelerometer cut points in preschool children.

Science.gov (United States)

van Cauwenberghe, Eveline; Labarque, Valery; Trost, Stewart G; de Bourdeaudhuij, Ilse; Cardon, Greet

2011-06-01

The present study aimed to develop accelerometer cut points to classify physical activities (PA) by intensity in preschoolers and to investigate discrepancies in PA levels when applying various accelerometer cut points. To calibrate the accelerometer, 18 preschoolers (5.8 ± 0.4 years) performed eleven structured activities and one free play session while wearing a GT1M ActiGraph accelerometer using 15 s epochs. The structured activities were chosen based on the direct observation system Children's Activity Rating Scale (CARS) while the criterion measure of PA intensity during free play was provided using a second-by-second observation protocol (modified CARS). Receiver Operating Characteristic (ROC) curve analyses were used to determine the accelerometer cut points. To examine the classification differences, accelerometer data of four consecutive days from 114 preschoolers (5.5 ± 0.3 years) were classified by intensity according to previously published and the newly developed accelerometer cut points. Differences in predicted PA levels were evaluated using repeated measures ANOVA and Chi Square test. Cut points were identified at 373 counts/15 s for light (sensitivity: 86%; specificity: 91%; Area under ROC curve: 0.95), 585 counts/15 s for moderate (87%; 82%; 0.91) and 881 counts/15 s for vigorous PA (88%; 91%; 0.94). Further, applying various accelerometer cut points to the same data resulted in statistically and biologically significant differences in PA. Accelerometer cut points were developed with good discriminatory power for differentiating between PA levels in preschoolers and the choice of accelerometer cut points can result in large discrepancies.

Variation between cut chrysanthemum cultivars in response to suboptimal temperature

NARCIS (Netherlands)

Ploeg, van der A.; Kularathne, R.J.K.N.; Carvalho, S.M.P.; Heuvelink, E.

2007-01-01

To breed for more energy-efficient cut chrysanthemum (Chrysanthemum morifolium Ramat.) cultivars it is important to know the variation of the temperature response existing in modern cultivars. In a greenhouse experiment with 25 chrysanthemum cultivars, a significant variation was observed in

Information Commons Features Cutting-Edge Conservation and Technology

Science.gov (United States)

Gilroy, Marilyn

2011-01-01

This article features Richard J. Klarchek Information Commons (IC) at Loyola University Chicago, an all-glass library building on the shore of Chicago's Lake Michigan that is not only a state-of-the-art digital research library and study space--it also runs on cutting-edge energy technology. The building has attracted attention and visitors from…

Fuel specification, energy consumption and CO2 emission in oil refineries

International Nuclear Information System (INIS)

Szklo, Alexandre; Schaeffer, Roberto

2007-01-01

The more stringent environmental quality specifications for oil products worldwide are tending to step up energy use and, consequently, CO 2 emissions at refineries. In Brazil, for example, the stipulated reduction in the sulfur content of diesel and gasoline between 2002 and 2009 should increase the energy use of Brazil's refining industry by around 30%, with effects on its CO 2 emissions. Thus, the world refining industry must deal with trade-offs between emissions of pollutants with local impacts (due to fuel specifications) and emissions of pollutants with global impacts (due to the increased energy use at refineries to remove contaminants from oil products). Two promising technology options for refineries could ease this clash in the near-to-mid term: the reduction per se of the energy use at the refinery; and the development of treatment processes using non-hydrogen consuming techniques. For instance, in Brazilian refineries, the expanded energy use resulting from severe hydrotreatment to comply with the more stringent specifications of oil products may be almost completely offset by energy saving options and alternative desulfurization techniques, if barriers to invest in technological innovations are overcome. (author)

The effect of silage cutting height on the nutritive value of a normal corn silage hybrid compared with brown midrib corn silage fed to lactating cows.

Science.gov (United States)

Kung, L; Moulder, B M; Mulrooney, C M; Teller, R S; Schmidt, R J

2008-04-01

A brown midrib (BMR) hybrid and a silage-specific non-BMR (7511FQ) hybrid were harvested at a normal cut height leaving 10 to 15 cm of stalk in the field. The non-BMR hybrid was also cut at a greater height leaving 45 to 50 cm of stalk. Cutting high increased the concentrations of dry matter (+4%), crude protein (+5%), net energy for lactation (+3%), and starch (+7%), but decreased the concentrations of acid detergent fiber (-9%), neutral detergent fiber (-8%), and acid detergent lignin (-13%) for 7511FQ. As expected, the BMR corn silage was 30% lower in lignin concentration than 7511FQ. After 30 h of in vitro ruminal fermentation, the digestibility of neutral detergent fiber for normal cut 7511FQ, the same hybrid cut high, and the normal cut BMR hybrid were 51.7, 51.4, and 63.5%, respectively. Twenty-seven multiparous lactating cows were fed a total mixed ration composed of the respective silages (45% of dry matter) with alfalfa haylage (5%), alfalfa hay (5%), and concentrate (45%) (to make the TMR isocaloric and isonitrogenous) in a study with a 3 x 3 Latin square design with 21-d periods. Milk production was greater for cows fed the BMR hybrid (48.8 kg/d) compared with those fed the normal cut 7511FQ (46.8 kg/d) or cut high (47.7 kg/d). Dry matter intake was not affected by treatment. Feed efficiency for cows fed the BMR silage (1.83) was greater than for those fed high-cut 7511FQ (1.75), but was not different from cows fed the normal cut 7511FQ (1.77). Cows fed the BMR silage had milk with greater concentrations of lactose but lower milk urea nitrogen than cows on other treatments. Harvesting a silage-specific, non-BMR corn hybrid at a high harvest height improved its nutritive content, but the improvement in feeding value was not equivalent to that found when cows were fed BMR corn silage.

Soaking grapevine cuttings in water: a potential source of cross contamination by micro-organisms

Directory of Open Access Journals (Sweden)

Helen WAITE

2013-09-01

Full Text Available Grapevine nurseries soak cuttings in water during propagation to compensate for dehydration and promote root initiation. However, trunk disease pathogens have been isolated from soaking water, indicating cross contamination. Cuttings of Vitis vinifera cv. Sunmuscat and V. berlandieri x V. rupestris rootstock cv. 140 Ruggeri were immersed in sterilized, deionised water for 1, 2, 4, 8 and 16 h. The soaking water was cultured (25°C for 3 days on non-specific and specific media for fungi and bacteria. The base of each cutting was debarked and trimmed and three 3 mm thick, contiguous, transverse slices of wood cultured at 25°C for 3 days. The soaking water for both cultivars became contaminated with microorganisms within the first hour. Numbers of fungi iso-lated from the wood slices soaked for one hour were significantly greater than those from non-soaked cuttings. The number of bacterial colonies growing from the wood slices increased after soaking for 2‒4 h in Sunmuscat. In a second experiment Shiraz cuttings were soaked for 1, 2, 4, 8 and 24 h. The soaking water became contaminated within the first hour but only the bacterial count increased significantly over time. Microorganisms also established on the container surfaces within the first hour although there were no significant increases over 24 h. These results confirm that soaking cuttings is a potential cause of cross contamination and demonstrate contamination of cuttings occurs after relatively short periods of soaking. Avoiding exposing cuttings to water will reduce the transmission of trunk diseases in propagation.

Prototype arc saw design and cutting trials

International Nuclear Information System (INIS)

Allison, G.S.

1980-09-01

A program was initiated to develop the arc saw as a tool capable of removing the end fittings from spent nuclear fuel bundles. A special arc saw for this purpose was designed, installed at the Pacific Northwest Laboratory and satisfactorily operated to remove end fittings from simulated, nonradioactive fuel bundles. The design of the arc saw included consideration of the cutting environment, power supply size, control equipment, and work piece size. Several simulated fuel bundles were cut to demonstrate that the arc saw met design specifications. Although the arc saw development program was curtailed before significant performance data could be collected, tests indicate that the arc saw is a good means of cropping spent fuel bundles and is well suited to remote operation and maintenance

Cutting system for burnable poison rod

International Nuclear Information System (INIS)

Shiina, Atsushi; Toyama, Norihide; Koshino, Yasuo; Fujii, Toshio

1989-01-01

Burnable poison rods attached to spent fuels are contained in a containing box and transported to a receiving pool. The burnable poison rod-containing box is provisionally situated by the operation to a handling device to a provisional setting rack in a cutting pool and attached to a cutting guide of a cutting device upon cutting. The burnable poison rod is cut only in a cutting pool water and tritium generated upon cutting is dissolved into the cutting pool water. Diffusion of tritium is thus restricted. Further, the cutting pool is isolated by a partition device from the receiving pool during cutting of the burnable poison rod. Accordingly, water in which tritium is dissolved is inhibited from moving to the receiving pool and prevail of tritium contamination can be avoided. (T.M.)

High-precision cutting of polyimide film using femtosecond laser for the application in flexible electronics

Science.gov (United States)

Ganin, D. V.; Lapshin, K. E.; Obidin, A. Z.; Vartapetov, S. K.

2018-01-01

The experimental results of cutting a polyimide film on the optical glass substrate by means of femtosecond lasers are given. Two modes of laser cutting of this film without damages to a glass base are determined. The first is the photo graphitization using a high repetition rate femtosecond laser. The second is ablative, under the effect of femtosecond laser pulses with high energy and low repetition rate. Cutting of semiconductor chips formed on the polyimide film surface is successfully demonstrated.

The continuous cut-off method and the relativistic scattering of spin-1/2 particles

International Nuclear Information System (INIS)

Dolinszky, T.

1979-07-01

A high energy formula, obtained in the framework of the continuous cut-off approach, is shown to improve the correctness of the standard phase shift expression for Dirac scattering by two orders of magnitude in energy. (author)

Numerical modelling of orthogonal cutting: application to woodworking with a bench plane

OpenAIRE

Nairn, John A.

2016-01-01

A numerical model for orthogonal cutting using the material point method was applied to woodcutting using a bench plane. The cutting process was modelled by accounting for surface energy associated with wood fracture toughness for crack growth parallel to the grain. By using damping to deal with dynamic crack propagation and modelling all contact between wood and the plane, simulations could initiate chip formation and proceed into steady-state chip propagation including chip curling. Once st...

Influence of Lay Plan Solution in Fabric Efficiency and Consume in Cutting Section

OpenAIRE

Dumishllari Elmira; Guxho Genti

2016-01-01

One cutting order may require several lies and markers to achieve optimal efficiency and selection of right Lay Plan is one of the major challenges in cutting section, in a way to lead in fabric economy and reduced costs. The main purpose of this paper is to determine the best solution of lay plan and its influence, in the cutting room, starting from the analysis of the lay indicators calculations. We have studied an order with 200 jackets, with specific sizes. Markers are made by Gemini CAD ...

Spectrally selective solar absorber with sharp and temperature dependent cut-off based on semiconductor nanowire arrays

Science.gov (United States)

Wang, Yang; Zhou, Lin; Zheng, Qinghui; Lu, Hong; Gan, Qiaoqiang; Yu, Zongfu; Zhu, Jia

2017-05-01

Spectrally selective absorbers (SSA) with high selectivity of absorption and sharp cut-off between high absorptivity and low emissivity are critical for efficient solar energy conversion. Here, we report the semiconductor nanowire enabled SSA with not only high absorption selectivity but also temperature dependent sharp absorption cut-off. By taking advantage of the temperature dependent bandgap of semiconductors, we systematically demonstrate that the absorption cut-off profile of the semiconductor-nanowire-based SSA can be flexibly tuned, which is quite different from most of the other SSA reported so far. As an example, silicon nanowire based selective absorbers are fabricated, with the measured absorption efficiency above (below) bandgap ˜97% (15%) combined with an extremely sharp absorption cut-off (transition region ˜200 nm), the sharpest SSA demonstrated so far. The demonstrated semiconductor-nanowire-based SSA can enable a high solar thermal efficiency of ≳86% under a wide range of operating conditions, which would be competitive candidates for the concentrated solar energy utilizations.

Leaves Of Cut Rose Flower Convert Exogenously Applied Glucose To Sucrose And Translocate It To Petals

Directory of Open Access Journals (Sweden)

Horibe Takanori

2014-12-01

Full Text Available To understand the role that the leaves play in the translocation of soluble carbohydrates in cut rose flowers, we first evaluated the effect of leaf removal on flower quality and the sugar content in petals. Cut rose flowers with leaves had higher soluble sugar content in petals compared with cut flower without leaves. Next, we treated cut flowers with radioactive glucose to clarify translocation routes of exogenously applied sugar. There was no significant difference between the specific radioactivity of sucrose and glucose in leaves, but specific radioactivity of sucrose in petals was much higher than that of glucose. These results suggested that most of the exogenously applied glucose first moved to the leaves, where it was converted into sucrose and then the synthesised sucrose was translocated to the petals. Our results showed that the leaves of cut rose flowers play an important role in the metabolism and transportation of exogenously applied soluble carbohydrates toward the petals, thus contributing to sustaining the post-harvest quality.

Clean Cities: Building Partnerships to Cut Petroleum Use in Transportation

Energy Technology Data Exchange (ETDEWEB)

None

2016-01-07

This brochure provides an overview of the U.S. Department of Energy's (DOE's) Clean Cities program, which advances the nation's economic, environmental, and energy security by supporting local actions to cut petroleum use in transportation. At the national level, the program develops and promotes publications, tools, and other unique resources. At the local level, nearly 100 coalitions leverage these resources to create networks of stakeholders.

Clean Cities: Building Partnerships to Cut Petroleum Use in Transportation

Energy Technology Data Exchange (ETDEWEB)

2016-01-01

This brochure provides an overview of the U.S. Department of Energy's (DOE's) Clean Cities program, which advances the nation's economic, environmental, and energy security by supporting local actions to cut petroleum use in transportation. At the national level, the program develops and promotes publications, tools, and other unique resources. At the local level, nearly 100 coalitions leverage these resources to create networks of stakeholders.

New Nanostructured Li 2 S/Silicon Rechargeable Battery with High Specific Energy

KAUST Repository

Yang, Yuan

2010-04-14

Rechargeable lithium ion batteries are important energy storage devices; however, the specific energy of existing lithium ion batteries is still insufficient for many applications due to the limited specific charge capacity of the electrode materials. The recent development of sulfur/mesoporous carbon nanocomposite cathodes represents a particularly exciting advance, but in full battery cells, sulfur-based cathodes have to be paired with metallic lithium anodes as the lithium source, which can result in serious safety issues. Here we report a novel lithium metal-free battery consisting of a Li 2S/mesoporous carbon composite cathode and a silicon nanowire anode. This new battery yields a theoretical specific energy of 1550 Wh kg ?1, which is four times that of the theoretical specific energy of existing lithium-ion batteries based on LiCoO2 cathodes and graphite anodes (∼410 Wh kg?1). The nanostructured design of both electrodes assists in overcoming the issues associated with using sulfur compounds and silicon in lithium-ion batteries, including poor electrical conductivity, significant structural changes, and volume expansion. We have experimentally realized an initial discharge specific energy of 630 Wh kg ?1 based on the mass of the active electrode materials. © 2010 American Chemical Society.

Laser welding, cutting and surface treatment

International Nuclear Information System (INIS)

Crafer, R.C.

1984-01-01

Fourteen articles cover a wide range of laser applications in welding, cutting and surface treatment. Future trends are covered as well as specific applications in shipbuilding, the manufacture of heart pacemakers, in the electronics industry, in automobile production and in the aeroengine industry. Safety with industrial lasers and the measurement of laser beam parameters are also included. One article on 'Lasers in the Nuclear Industry' is indexed separately. (U.K.)

Theoretical Models for Orthogonal Cutting

DEFF Research Database (Denmark)

De Chiffre, Leonardo

This review of simple models for orthogonal cutting was extracted from: “L. De Chiffre: Metal Cutting Mechanics and Applications, D.Sc. Thesis, Technical University of Denmark, 1990.”......This review of simple models for orthogonal cutting was extracted from: “L. De Chiffre: Metal Cutting Mechanics and Applications, D.Sc. Thesis, Technical University of Denmark, 1990.”...

Laser circular cutting of Kevlar sheets: Analysis of thermal stress filed and assessment of cutting geometry

Science.gov (United States)

Yilbas, B. S.; Akhtar, S. S.; Karatas, C.

2017-11-01

A Kevlar laminate has negative thermal expansion coefficient, which makes it difficult to machine at room temperaures using the conventional cutting tools. Contararily, laser machining of a Kevlar laminate provides advantages over the conventional methods because of the non-mechanical contact between the cutting tool and the workpiece. In the present study, laser circular cutting of Kevlar laminate is considered. The experiment is carried out to examine and evaluate the cutting sections. Temperature and stress fields formed in the cutting section are simulated in line with the experimental study. The influence of hole diameters on temperature and stress fields are investigated incorporating two different hole diameters. It is found that the Kevlar laminate cutting section is free from large size asperities such as large scale sideways burnings and attachemnt of charred residues. The maximum temperature along the cutting circumference remains higher for the large diameter hole than that of the small diameter hole. Temperature decay is sharp around the cutting section in the region where the cutting terminates. This, in turn, results in high temperature gradients and the thermal strain in the cutting region. von Mises stress remains high in the region where temperature gradients are high. von Mises stress follows similar to the trend of temperature decay around the cutting edges.

Teaching learning algorithm based optimization of kerf deviations in pulsed Nd:YAG laser cutting of Kevlar-29 composite laminates

Science.gov (United States)

Gautam, Girish Dutt; Pandey, Arun Kumar

2018-03-01

Kevlar is the most popular aramid fiber and most commonly used in different technologically advanced industries for various applications. But the precise cutting of Kevlar composite laminates is a difficult task. The conventional cutting methods face various defects such as delamination, burr formation, fiber pullout with poor surface quality and their mechanical performance is greatly affected by these defects. The laser beam machining may be an alternative of the conventional cutting processes due to its non-contact nature, requirement of low specific energy with higher production rate. But this process also faces some problems that may be minimized by operating the machine at optimum parameters levels. This research paper examines the effective utilization of the Nd:YAG laser cutting system on difficult-to-cut Kevlar-29 composite laminates. The objective of the proposed work is to find the optimum process parameters settings for getting the minimum kerf deviations at both sides. The experiments have been conducted on Kevlar-29 composite laminates having thickness 1.25 mm by using Box-Benkhen design with two center points. The experimental data have been used for the optimization by using the proposed methodology. For the optimization, Teaching learning Algorithm based approach has been employed to obtain the minimum kerf deviation at bottom and top sides. A self coded Matlab program has been developed by using the proposed methodology and this program has been used for the optimization. Finally, the confirmation tests have been performed to compare the experimental and optimum results obtained by the proposed methodology. The comparison results show that the machining performance in the laser beam cutting process has been remarkably improved through proposed approach. Finally, the influence of different laser cutting parameters such as lamp current, pulse frequency, pulse width, compressed air pressure and cutting speed on top kerf deviation and bottom kerf

Visual illusion in mass estimation of cut food.

Science.gov (United States)

Wada, Yuji; Tsuzuki, Daisuke; Kobayashi, Naoki; Hayakawa, Fumiyo; Kohyama, Kaoru

2007-07-01

We investigated the effect of the appearance of cut food on visual mass estimation. In this experiment, we manipulated the shape (e.g., a block, fine strips, or small cubes) of food samples of various masses, and presented them on a CRT display as stimuli. Eleven subjects participated in tasks to choose the picture of the food sample which they felt indicated a target mass. We used raw carrots and surimi (ground fish) gel as hard and soft samples, respectively. The results clearly confirm an existence of an illusion, and this indicates that the appearance of food interferes with visual mass estimation. Specifically, participants often overestimated the mass of finely cut food, especially fine strips, whereas they could accurately estimate the mass of block samples, regardless of the physical characteristics of the foods. The overestimation of the mass of cut food increased with the food's actual mass, and was particularly obvious with increases of apparent volume when cut into fine strips. These results suggest that the apparent volume of a food sample effects the visual estimation of its mass. Hence we can conclude that there are illusions associated with the visual presentation of food that may influence various food impressions, including satisfaction and eating behaviour.

Characterization of scraps produced by the industrial laser cutting of steels

Energy Technology Data Exchange (ETDEWEB)

Mercader, R. C. [Universidad Nacional de La Plata, Departamento de Fisica, IFLP-CCT-La Plata, Facultad de Ciencias Exactas (Argentina); Marchetti, S. G., E-mail: march@quimica.unlp.edu.ar; Bengoa, J. F. [CINDECA. Fac. Cs. Exactas, UNLP-CICPBA-CCT-CONICET (Argentina); Punte, G. [Universidad Nacional de La Plata, Departamento de Fisica, IFLP-CCT-La Plata, Facultad de Ciencias Exactas (Argentina); Cabanillas, E. D. [Comision Nacional, de Energia Atomica, CONICET and Departamento de Combustibles Nucleares (Argentina)

2010-01-15

We have studied some properties relevant for technological applications of the debris produced by industrial laser cutting of steels. The investigated material is made up of spheroidal particles, hollow and solid, which get oxidized over the cutting process, and that we have reduced afterwards in a H{sub 2} atmosphere. The samples, before and after the reduction, were characterized by X-ray diffraction, scanning electron microscopy, specific surface area and Moessbauer spectroscopy. We have found that, after the reduction treatment, the shape remains unchanged but that the chemical composition and the physical properties of the external and internal surface structures are modified. In particular, the specific surface area of the material increased by one order of magnitude.

The influence of mechanical properties of workpiece material on the main cutting force in face milling

Directory of Open Access Journals (Sweden)

M. Sekulić

2010-10-01

Full Text Available The paper presents the research into cutting forces in face milling of three different materials: steel Č 4732 (EN42CrMo4, nodular cast iron NL500 (EN-GJS-500-7 and silumine AlSi10Mg (EN AC-AlSi10Mg. Obtained results show that hardness and tensile strength values of workpiece material have a significant influence on the main cutting force, and thereby on the cutting energy in machining.

Energy modeling: nuclear energy as China's main energy after 2040

International Nuclear Information System (INIS)

Guo Xingqu

1987-01-01

According to the energy modeling and the strategic forecast of China's economic development and population, the energy demand in China in the coming century has been calculated yearly by computer simulation. It is shown by the calculation results that the primary energy consumption in 2050 will be 3.37-4.25 times as that of 2000. The fossil energy will still be the main energy during the early stage of 21st century, but it will be cut down rapidly since 2020s as its annual consumption is increased to 1.656-2.044 x 10 9 tce/a. Because the fossil fuel ressources in China are limited, more and more fossil fuel will be mainly turned to chemical products, and the environmental pollution will be serious if we still use the fossil as a main fuel widely. The amount of renewable energy will be increasing, but its share in the primary energy consumption will be cut down from 36% to about 20% during the first half of next century and then will maintain this portion. In this case, the nuclear energy will be developed rapidly during the early stage of next century and will become the main energy since 2040. The methodology of energy forecast has also been reviewed

ELISA Cut-off Point for the Diagnosis of Human Brucellosis; a Comparison with Serum Agglutination Test

Directory of Open Access Journals (Sweden)

Anahita Sanaei Dashti

2012-03-01

Full Text Available Background: Brucellosis is a world-wide disease, which has a diverse clinical manifestation, and its diagnosis has to be proven by laboratory data. Serum agglutination test (SAT is the most-widely used test for diagnosing brucellosis. The enzyme linked immunosorbent assay (ELISA can also determine specific antibody classes against brucella. It is a sensitive, simple and rapid test, which could be an acceptable alternative to SAT with fewer limitations, however, like any other new test it should be further evaluated and standardized for various populations. This study was planned to determine an optimal cut-off point, for ELISA which would offer maximum sensitivity and specificity for the test when compared to SAT.Methods: Four hundred and seven patients with fever and other compatible symptoms of brucellosis were enrolled in the study. Serum agglutination test, 2-Mercaptoethanol test, and ELISA were performed on their sera. Results: The cut-off point of 53 IU/ml of ELISA-IgG yielded the maximal sensitivity and specificity comparing to the other levels of ELISA-IgG, and was considered the best cut off-point of ELISA-IgG to diagnose acute brucellosis. At this cut-off, the sensitivity, specificity, positive predictive value, negative predictive value, positive likelihood ratio, and negative likelihood ratio were 84.09%, 85.38%, 62.20, 94.90, 5.75, 0.18, respectively.Conclusion: The best cut-off point of ELISA-IgG is 53 IU/ml, which yields the maximal sensitivity and specificity to diagnose acute brucellosis.

Consumer evaluation of palatability characteristics of a beef value-added cut compared to common retail cuts.

Science.gov (United States)

Lepper-Blilie, A N; Berg, E P; Germolus, A J; Buchanan, D S; Berg, P T

2014-01-01

The objectives of this study were to educate consumers about value-added beef cuts and evaluate their palatability responses of a value cut and three traditional cuts. Three hundred and twenty-two individuals participated in the beef value cut education seminar series presented by trained beef industry educators. Seminar participants evaluated tenderness, juiciness, flavor, and overall like of four samples, bottom round, top sirloin, ribeye, and a value cut (Delmonico or Denver), on a 9-point scale. The ribeye and the value cut were found to be similar in all four attributes and differed from the top sirloin and bottom round. Correlations and regression analysis found that flavor was the largest influencing factor for overall like for the ribeye, value cut, and top sirloin. The value cut is comparable to the ribeye and can be a less expensive replacement. © 2013.

Investigation of specific applications of laser cutting for dismantling of nuclear power plants

International Nuclear Information System (INIS)

Tarroni, G.; De Zaiacomo, T.; Melandri, C.; Formignani, M.; Barilli, L.; Di Fino, M.; Picini, P.; Galuppi, G.; Rocca, C.; Manassero, G.; Migliorati, B.

1991-02-01

The aim of this work, performed on an experimental basis in a frame of strict collaboration between industry (FIAT-CIEI and FIAT-CRF in Turin) and public research laboratories (ENEA-PAS-FIBI in Bologna, ENEA-PAS-ISP and ENEA-TIB-TECNLAS in Rome) and supported by a CEC contract, was to bring out the items for better evaluation of the laser beam application possibilities in dismantling nuclear power plants. The main topics of the research have been: 1) study and definition of the relevant basic parameters ruling the aerosol generation rate and behaviour in terms of physical and chemical characteristics. This work has been performed in a facility specifically designed for aerosol measurements and equipped with a 2kW laser source; 2) study of the feasibility of local abatement of the aerosols produced and of the pressure drop in the HEPA filters; 3) study of long distance transmission of the laser beam power performed with a 5kW laser source with an evaluation of the power loss and beam characteristic modifications; 4) study of laser beam technique application for dismantling the Garigliano power plant steam drum in order to better demonstrate the feasibility of the use of this technique. The research resulted in the conclusion that the laser beam is actually appropriate for long distance dismantling of metal components. Although the main aspects of the laser cutting process have been examined, some problems remain to be investigated. This could be performed, after proper cost-benefit evaluation, during a future decommissioning programme. (author)

Investigation of specific applications of laser cutting for dismantling of nuclear power plants

International Nuclear Information System (INIS)

Migliorati, B.; Difino, M.; Manassero, G.

1990-01-01

The aim of this work, performed on an experimental basis in a frame of strict collaboration between industry (Fiat-CIEI and Fiat-CRF in Turin) and public research laboratories (ENEA-PAS-FIBI in Bologna, ENEA-PAS-ISP and ENEA-TIB-TECNLAS in Rome) and supported by a CEC contract, was to bring out the items for better evaluation of the laser beam application possibilities in dismantling nuclear power plants. The main topics of the research have been: (i) study and definition of the relevant basic parameters ruling the aerosol generation rate and behaviour in terms of physical and chemical characteristics. This work has been performed in a facility specifically designed for aerosol measurements and equipped with a 2kW laser source; (ii) study of the feasibility of local abatement of the aerosols produced and of the pressure drop in the HEPA filters; (iii) study of long-distance transmission of the laser beam power performed with a 5KW laser source with an evaluation of the power loss and beam characteristic modifications; (iv) study of laser beam technique application for dismantling the Garigliano power plant steam drum in order to better demonstrate the feasibility of the use of this technique. The research resulted in the conclusion that the laser beam is actually appropriate for long-distance dismantling of metal components. Although the main aspects of the laser cutting process have been examined, some problems remain to be investigated. This could be performed, after proper cost-benefit evaluation, during a future decommissioning programme

Investigation of specific applications of laser cutting for dismantling of nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Tarroni, G; De Zaiacomo, T; Melandri, C; Formignani, M; Barilli, L [ENEA - Area Energia, Ambiente e Salute - Centro Ricerche Energia ' Ezio Clementel' - Bologna (Italy); Di Fino, M [ENEA - Area Energia, Ambiente e Salute, Centro Ricerche Energia, Frascati, Rome (Italy); Picini, P; Galuppi, G; Rocca, C [ENEA - Area Energia, Ambiente e Salute, Centro Ricerche Energia, Casaccia, Rome (Italy); Manassero, G [Centro Ricerche FIAT, Orbassano, Torino (Italy); Migliorati, B [FIAT-CIEI, Torino (Italy)

1991-02-15

The aim of this work, performed on an experimental basis in a frame of strict collaboration between industry (FIAT-CIEI and FIAT-CRF in Turin) and public research laboratories (ENEA-PAS-FIBI in Bologna, ENEA-PAS-ISP and ENEA-TIB-TECNLAS in Rome) and supported by a CEC contract, was to bring out the items for better evaluation of the laser beam application possibilities in dismantling nuclear power plants. The main topics of the research have been: 1) study and definition of the relevant basic parameters ruling the aerosol generation rate and behaviour in terms of physical and chemical characteristics. This work has been performed in a facility specifically designed for aerosol measurements and equipped with a 2kW laser source; 2) study of the feasibility of local abatement of the aerosols produced and of the pressure drop in the HEPA filters; 3) study of long distance transmission of the laser beam power performed with a 5kW laser source with an evaluation of the power loss and beam characteristic modifications; 4) study of laser beam technique application for dismantling the Garigliano power plant steam drum in order to better demonstrate the feasibility of the use of this technique. The research resulted in the conclusion that the laser beam is actually appropriate for long distance dismantling of metal components. Although the main aspects of the laser cutting process have been examined, some problems remain to be investigated. This could be performed, after proper cost-benefit evaluation, during a future decommissioning programme. (author)

Abrasive water jet cutting technique for biological shield concrete dismantlement

International Nuclear Information System (INIS)

Konno, T.; Narazaki, T.; Yokota, M.; Yoshida, H.; Miura, M.; Miyazaki, Y.

1987-01-01

The Japan Atomic Energy Research Institute (JAERI) is developing the abrasive-water jet cutting system to be applied to dismantling the biological shield walls of the JPDR as a part of the reactor dismantling technology development project. This is a total system for dismantling highly activated concrete. The concrete biological shield wall is cut into blocks by driving the abrasive-water jet nozzle, which is operated with a remote, automated control system. In this system, the concrete blocks are removed to a container, while the slurry and dust/mist which are generated during cutting are collected and treated, both automatically. It is a very practical method and will quite probably by used for actual dismantling of commercial power reactors in the future because it can minimize workers' exposure to radioactivity during dismantling, contributes to preventing diffusion of radiation, and reduces the volume of contaminated secondary waste

Current MUAC Cut-Offs to Screen for Acute Malnutrition Need to Be Adapted to Gender and Age: The Example of Cambodia

Science.gov (United States)

Fiorentino, Marion; Sophonneary, Prak; Laillou, Arnaud; Whitney, Sophie; de Groot, Richard; Perignon, Marlène; Kuong, Khov; Berger, Jacques; Wieringa, Frank T.

2016-01-01

Background Early identification of children malnutrition is a priority. Acute malnutrition is defined by the World Health Organization as a mid-upper-arm circumference (MUAC) malnutrition in communities, but MUAC cut-offs currently recommended by WHO do not identify the majority of children with weight-for-height Z-score (5 yrs. Therefore, this study aimed at defining gender and age-specific cut-offs to improve sensitivity of MUAC as an indicator of acute malnutrition. Methods To establish new age and gender-specific MUAC cut-offs, pooled data was obtained for 14,173 children from 5 surveys in Cambodia (2011–2013). Sensitivity, false positive rates, and areas under receiver-operator characteristic curves (AUC) were calculated using wasting for children 80% with the new cut-offs in comparison with the current WHO cut-offs. Conclusion Gender and age specific MUAC cut-offs drastically increased sensitivity to identify children with WHZ-score malnutrition at the community level. PMID:26840899

Cutting a drop of water pinned by wire loops using a superhydrophobic surface and knife.

Directory of Open Access Journals (Sweden)

Ryan Yanashima

Full Text Available A water drop on a superhydrophobic surface that is pinned by wire loops can be reproducibly cut without formation of satellite droplets. Drops placed on low-density polyethylene surfaces and Teflon-coated glass slides were cut with superhydrophobic knives of low-density polyethylene and treated copper or zinc sheets, respectively. Distortion of drop shape by the superhydrophobic knife enables a clean break. The driving force for droplet formation arises from the lower surface free energy for two separate drops, and it is modeled as a 2-D system. An estimate of the free energy change serves to guide when droplets will form based on the variation of drop volume, loop spacing and knife depth. Combining the cutting process with an electrofocusing driving force could enable a reproducible biomolecular separation without troubling satellite drop formation.

Flux cutting in superconductors

International Nuclear Information System (INIS)

Campbell, A M

2011-01-01

This paper describes experiments and theories of flux cutting in superconductors. The use of the flux line picture in free space is discussed. In superconductors cutting can either be by means of flux at an angle to other layers of flux, as in longitudinal current experiments, or due to shearing of the vortex lattice as in grain boundaries in YBCO. Experiments on longitudinal currents can be interpreted in terms of flux rings penetrating axial lines. More physical models of flux cutting are discussed but all predict much larger flux cutting forces than are observed. Also, cutting is occurring at angles between vortices of about one millidegree which is hard to explain. The double critical state model and its developments are discussed in relation to experiments on crossed and rotating fields. A new experiment suggested by Clem gives more direct information. It shows that an elliptical yield surface of the critical state works well, but none of the theoretical proposals for determining the direction of E are universally applicable. It appears that, as soon as any flux flow takes place, cutting also occurs. The conclusion is that new theories are required. (perspective)

Chapter 11: Sample Design Cross-Cutting Protocol. The Uniform Methods Project: Methods for Determining Energy Efficiency Savings for Specific Measures

Energy Technology Data Exchange (ETDEWEB)

Kurnik, Charles W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Khawaja, M. Sami [The Cadmus Group, Portland, OR (United States); Rushton, Josh [The Cadmus Group, Portland, OR (United States); Keeling, Josh [The Cadmus Group, Portland, OR (United States)

2017-09-01

Evaluating an energy efficiency program requires assessing the total energy and demand saved through all of the energy efficiency measures provided by the program. For large programs, the direct assessment of savings for each participant would be cost-prohibitive. Even if a program is small enough that a full census could be managed, such an undertaking would almost always be an inefficient use of evaluation resources. The bulk of this chapter describes methods for minimizing and quantifying sampling error. Measurement error and regression error are discussed in various contexts in other chapters.

Development of underwater laser cutting technology

International Nuclear Information System (INIS)

Sato, Seiichi; Inaba, Takanori; Inose, Koutarou; Matsumoto, Naoyuki; Sakakibara, Yuji

2015-01-01

In is desirable to use remote underwater device for the decommissioning work of highly radioactive components such as the nuclear internals from a view point of reducing the ranitidine exposure to the worker. Underwater laser cutting technology has advantages. First advantage in underwater laser cutting technology is that low reaction force during cutting, namely, remote operability is superior. Second point is that underwater laser cutting generates a little amount of secondary waste, because cutting kerf size is very small. Third point is that underwater laser cutting has low risk of the process delay, because device trouble is hard to happen. While underwater laser cutting has many advantages, the careful consideration in the safe treatment of the offgas which underwater laser cutting generates is necessary. This paper describes outline of underwater laser cutting technology developed by IHI Corporation (IHI) and that this technology is effective in various dismantling works in water. (author)

A new device to test cutting efficiency of mechanical endodontic instruments

Science.gov (United States)

Rubini, Alessio Giansiracusa; Plotino, Gianluca; Al-Sudani, Dina; Grande, Nicola M.; Putorti, Ermanno; Sonnino, GianPaolo; Cotti, Elisabetta; Testarelli, Luca; Gambarini, Gianluca

2014-01-01

Background The purpose of the present study was to introduce a new device specifically designed to evaluate the cutting efficiency of mechanically driven endodontic instruments. Material/Methods Twenty new Reciproc R25 (VDW, Munich, Germany) files were used to be investigated in the new device developed to test the cutting ability of endodontic instruments. The device consists of a main frame to which a mobile plastic support for the hand-piece is connected and a stainless-steel block containing a Plexiglas block against which the cutting efficiency of the instruments was tested. The length of the block cut in 1 minute was measured in a computerized program with a precision of 0.1mm. The instruments were activated by using a torque-controlled motor (Silver Reciproc; VDW, Munich, Germany) in a reciprocating movement by the “Reciproc ALL” program (Group 1) and in counter-clockwise rotation at 300 rpm (Group 2). Mean and standard deviations of each group were calculated and data were statistically analyzed with a one-way ANOVA test (P0.05). Conclusions The cutting testing device evaluated in the present study was reliable and easy to use and may be effectively used to test cutting efficiency of both rotary and reciprocating mechanical endodontic instruments. PMID:24603777

Investigation of wear land and rate of locally made HSS cutting tool

Science.gov (United States)

Afolalu, S. A.; Abioye, A. A.; Dirisu, J. O.; Okokpujie, I. P.; Ajayi, O. O.; Adetunji, O. R.

2018-04-01

Production technology and machining are inseparable with cutting operation playing important roles. Investigation of wear land and rate of cutting tool developed locally (C=0.56%) with an HSS cutting tool (C=0.65%) as a control was carried out. Wear rate test was carried out using Rotopol -V and Impact tester. The samples (12) of locally made cutting tools and one (1) sample of a control HSS cutting tool were weighed to get the initial weight and grit was fixed at a point for the sample to revolve at a specific time of 10 mins interval. Approach of macro transfer particles that involved mechanism of abrasion and adhesion which was termed as mechanical wear to handle abrasion adhesion processes was used in developing equation for growth wear at flank. It was observed from the wear test that best minimum wear rate of 1.09 × 10-8 and 2.053 × 10-8 for the tools developed and control were measured. MATLAB was used to simulate the wear land and rate under different conditions. Validated results of both the experimental and modeling showed that cutting speed has effect on wear rate while cutting time has predicted measure on wear land. Both experimental and modeling result showed best performances of tools developed over the control.

Wear mechanism of CBN cutting tool during high-speed machining of mold steel

International Nuclear Information System (INIS)

Farhat, Z.N.

2003-01-01

Wear behavior of cubic boron nitride (CBN) cutting tool when cutting P20 tool steel was investigated. Oblique cutting tests were performed on a CNC lathe using five speeds, namely, 240, 600 and 1000 m min -1 . The CBN cutting tools were found to be superior to tungsten carbide (WC) tools. Fourfold increase in productivity and significant reduction in chipping and cratering was achieved for CBN as compared to WC. Wear, as the width of the wear land (VB), was monitored at selected time intervals; furthermore, topography of worn surfaces was performed, using a profilometer. Wear characterization of the rake and the flank surfaces as well as of the collected chips was conducted using a scanning electron microscopy (SEM), backscattered electron imaging and energy depressive X-ray (EDX). It was found that deformation in the chips occurs by localized shear deformation and the dominant wear mechanism at all speeds used was identified to be diffusive wear. At a 1000 m min -1 cutting speed, a secondary wear mechanism was identified, which is melt wear, i.e., formation of low melting point Cr and Mn compounds with the tool material and the subsequent ejection from the cutting zone

Specific energy of cold crack initiation in welding low alloy high-strength steels

International Nuclear Information System (INIS)

Brednev, V.I.; Kasatkin, B.S.

1988-01-01

Methods for determination of energy spent on cold crack initiation, when testing welded joint samples by the Implant method, are described. Data on the effect of the steel alloying system, cooling rate of welded joints, content of diffusion hydrogen on the critical specific energy spent on the development of local plastic deformation upto cold crack initiation are presented. The value of specific energy spent on cold crack initiation is shown to be by two-three orders lower than the value of impact strength minimum accessible. The possibility to estimate welded joint resistance to cold crack initiation according to the critical specific energy is established

Genetic parameters of Visual Image Analysis primal cut carcass traits of commercial prime beef slaughter animals.

Science.gov (United States)

Moore, K L; Mrode, R; Coffey, M P

2017-10-01

Visual Image analysis (VIA) of carcass traits provides the opportunity to estimate carcass primal cut yields on large numbers of slaughter animals. This allows carcases to be better differentiated and farmers to be paid based on the primal cut yields. It also creates more accurate genetic selection due to high volumes of data which enables breeders to breed cattle that better meet the abattoir specifications and market requirements. In order to implement genetic evaluations for VIA primal cut yields, genetic parameters must first be estimated and that was the aim of this study. Slaughter records from the UK prime slaughter population for VIA carcass traits was available from two processing plants. After edits, there were 17 765 VIA carcass records for six primal cut traits, carcass weight as well as the EUROP conformation and fat class grades. Heritability estimates after traits were adjusted for age ranged from 0.32 (0.03) for EUROP fat to 0.46 (0.03) for VIA Topside primal cut yield. Adjusting the VIA primal cut yields for carcass weight reduced the heritability estimates, with estimates of primal cut yields ranging from 0.23 (0.03) for Fillet to 0.29 (0.03) for Knuckle. Genetic correlations between VIA primal cut yields adjusted for carcass weight were very strong, ranging from 0.40 (0.06) between Fillet and Striploin to 0.92 (0.02) between Topside and Silverside. EUROP conformation was also positively correlated with the VIA primal cuts with genetic correlation estimates ranging from 0.59 to 0.84, whereas EUROP fat was estimated to have moderate negative correlations with primal cut yields, estimates ranged from -0.11 to -0.46. Based on these genetic parameter estimates, genetic evaluation of VIA primal cut yields can be undertaken to allow the UK beef industry to select carcases that better meet abattoir specification and market requirements.

Cutting temperature measurement and material machinability

Directory of Open Access Journals (Sweden)

Nedić Bogdan P.

2014-01-01

Full Text Available Cutting temperature is very important parameter of cutting process. Around 90% of heat generated during cutting process is then away by sawdust, and the rest is transferred to the tool and workpiece. In this research cutting temperature was measured with artificial thermocouples and question of investigation of metal machinability from aspect of cutting temperature was analyzed. For investigation of material machinability during turning artificial thermocouple was placed just below the cutting top of insert, and for drilling thermocouples were placed through screw holes on the face surface. In this way was obtained simple, reliable, economic and accurate method for investigation of cutting machinability.

Stresses in ultrasonically assisted bone cutting

International Nuclear Information System (INIS)

Alam, K; Mitrofanov, A V; Silberschmidt, V V; Baeker, M

2009-01-01

Bone cutting is a frequently used procedure in the orthopaedic surgery. Modern cutting techniques, such as ultrasonic assisted drilling, enable surgeons to perform precision operations in facial and spinal surgeries. Advanced understanding of the mechanics of bone cutting assisted by ultrasonic vibration is required to minimise bone fractures and to optimise the technique performance. The paper presents results of finite element simulations on ultrasonic and conventional bone cutting analysing the effects of ultrasonic vibration on cutting forces and stress distribution. The developed model is used to study the effects of cutting and vibration parameters (e.g. amplitude and frequency) on the stress distributions in the cutting region.

Optimisation Of Cutting Parameters Of Composite Material Laser Cutting Process By Taguchi Method

Science.gov (United States)

Lokesh, S.; Niresh, J.; Neelakrishnan, S.; Rahul, S. P. Deepak

2018-03-01

The aim of this work is to develop a laser cutting process model that can predict the relationship between the process input parameters and resultant surface roughness, kerf width characteristics. The research conduct is based on the Design of Experiment (DOE) analysis. Response Surface Methodology (RSM) is used in this work. It is one of the most practical and most effective techniques to develop a process model. Even though RSM has been used for the optimization of the laser process, this research investigates laser cutting of materials like Composite wood (veneer)to be best circumstances of laser cutting using RSM process. The input parameters evaluated are focal length, power supply and cutting speed, the output responses being kerf width, surface roughness, temperature. To efficiently optimize and customize the kerf width and surface roughness characteristics, a machine laser cutting process model using Taguchi L9 orthogonal methodology was proposed.

Selection of Near Optimal Laser Cutting Parameters in CO2 Laser Cutting by the Taguchi Method

Directory of Open Access Journals (Sweden)

Miloš MADIĆ

2013-12-01

Full Text Available Identification of laser cutting conditions that are insensitive to parameter variations and noise is of great importance. This paper demonstrates the application of Taguchi method for optimization of surface roughness in CO2 laser cutting of stainless steel. The laser cutting experiment was planned and conducted according to the Taguchi’s experimental design using the L27 orthogonal array. Four laser cutting parameters such as laser power, cutting speed, assist gas pressure, and focus position were considered in the experiment. Using the analysis of means and analysis of variance, the significant laser cutting parameters were identified, and subsequently the optimal combination of laser cutting parameter levels was determined. The results showed that the cutting speed is the most significant parameter affecting the surface roughness whereas the influence of the assist gas pressure can be neglected. It was observed, however, that interaction effects have predominant influence over the main effects on the surface roughness.

How Can I Stop Cutting?

Science.gov (United States)

... Educators Search English Español How Can I Stop Cutting? KidsHealth / For Teens / How Can I Stop Cutting? ... in a soft, cozy blanket Substitutes for the Cutting Sensation You'll notice that all the tips ...

Energy-Specific Optimization of Attenuation Thresholds for Low-Energy Virtual Monoenergetic Images in Renal Lesion Evaluation.

Science.gov (United States)

Patel, Bhavik N; Farjat, Alfredo; Schabel, Christoph; Duvnjak, Petar; Mileto, Achille; Ramirez-Giraldo, Juan Carlos; Marin, Daniele

2018-05-01

The purpose of this study was to determine in vitro and in vivo the optimal threshold for renal lesion vascularity at low-energy (40-60 keV) virtual monoenergetic imaging. A rod simulating unenhanced renal parenchymal attenuation (35 HU) was fitted with a syringe containing water. Three iodinated solutions (0.38, 0.57, and 0.76 mg I/mL) were inserted into another rod that simulated enhanced renal parenchyma (180 HU). Rods were inserted into cylindric phantoms of three different body sizes and scanned with single- and dual-energy MDCT. In addition, 102 patients (32 men, 70 women; mean age, 66.8 ± 12.9 [SD] years) with 112 renal lesions (67 nonvascular, 45 vascular) measuring 1.1-8.9 cm underwent single-energy unenhanced and contrast-enhanced dual-energy CT. Optimal threshold attenuation values that differentiated vascular from nonvascular lesions at 40-60 keV were determined. Mean optimal threshold values were 30.2 ± 3.6 (standard error), 20.9 ± 1.3, and 16.1 ± 1.0 HU in the phantom, and 35.9 ± 3.6, 25.4 ± 1.8, and 17.8 ± 1.8 HU in the patients at 40, 50, and 60 keV. Sensitivity and specificity for the thresholds did not change significantly between low-energy and 70-keV virtual monoenergetic imaging (sensitivity, 87-98%; specificity, 90-91%). The AUC from 40 to 70 keV was 0.96 (95% CI, 0.93-0.99) to 0.98 (95% CI, 0.95-1.00). Low-energy virtual monoenergetic imaging at energy-specific optimized attenuation thresholds can be used for reliable characterization of renal lesions.

Cutting costs by achieving energy efficiency using monitoring, targeting and teamwork

Energy Technology Data Exchange (ETDEWEB)

Dittburner, D. [Unilever Canada, Toronto, ON (Canada)

2004-07-01

Unilever is a world leader of consumer goods with annual sales of $70 billion. This paper focuses on energy management projects developed at Unilever's Rexdale Plant, where 180 million pounds of edible oils and margarine are produced annually. The project is a response to corporate and market pressures to reduce costs. An overview of Unilever's relationship with Natural Resources Canada was provided. Results of the overall project were highlighted and included: $3 million in annual savings from increased efficiency in operations and equipment retrofits. An outline of the energy team at Unilever was presented, with their mission statement, rules and achievements, as well the company's overall goal of total productive manufacturing. A list of awards and financial incentives was presented, as well as details of financial savings incurred at the Rexdale Plant. Total energy reductions were presented, with a natural gas year to year comparison and utility to production ratios from 1999 to the present. A statement concerning the issue of corporate support by the vice president was provided. Seven steps to savings were presented, as well as details of the company's implementation of the steps. Details of the extended team involved in the project were provided, as well as extensive details about the employee awareness program instigated by the company, including a database of ideas achieved since 2001, as well as details of specific projects accomplished, with estimated savings for each project. An outline of the company's business model and methodology was presented, along with details of reduced costs, risk and improved management and communications. An outline of scoping studies was presented as well as a flow chart of projects and target-setting goals. Success factors were reviewed. Montage applications included energy management; performance contracting; energy forecasting; emissions and waste minimization; and cost allocation. tabs., figs.

Rooting of stem cuttings of ixora

Directory of Open Access Journals (Sweden)

Aline De Souza Silva

2015-08-01

Full Text Available The ixora is ornamental plant widely used in landscaping. In order to maximize the propagation of cuts, we evaluated the concentrations of auxin (indolbutiric acid and the presence of leaves on the rooting in cuts of Ixora coccinea L. The experiment was conducted in randomized block design, in factorial design 3x4, with three types of cuts (without leaf, with two or four leaves, four concentrations of indolbutiric acid (0, 1000, 2000 and 4000 mg L-1, with four replications and 10 cuts in each experimental unit. After 53 days of implantation the experiment, evaluated the survival(%, rooting(%, sprouting(%, formation of callus(%, number, length and biomass of roots formed. The interaction of the type of cuts with concentrations of auxin was not significant for any of the variables analyzed. The survival of cuttings was not influenced by the treatments. Cuts with two or four leaves presented rooting and length of roots above the cuttings without leaves. The application of auxin does not substitute the presence of leaf in cuts of ixora in vegetative propagation. The vegetative propagation by cut of ixora can be made without application of auxin, and the leaves must be maintained in the cuttings.

Modeling a Predictive Energy Equation Specific for Maintenance Hemodialysis.

Science.gov (United States)

Byham-Gray, Laura D; Parrott, J Scott; Peters, Emily N; Fogerite, Susan Gould; Hand, Rosa K; Ahrens, Sean; Marcus, Andrea Fleisch; Fiutem, Justin J

2017-03-01

Hypermetabolism is theorized in patients diagnosed with chronic kidney disease who are receiving maintenance hemodialysis (MHD). We aimed to distinguish key disease-specific determinants of resting energy expenditure to create a predictive energy equation that more precisely establishes energy needs with the intent of preventing protein-energy wasting. For this 3-year multisite cross-sectional study (N = 116), eligible participants were diagnosed with chronic kidney disease and were receiving MHD for at least 3 months. Predictors for the model included weight, sex, age, C-reactive protein (CRP), glycosylated hemoglobin, and serum creatinine. The outcome variable was measured resting energy expenditure (mREE). Regression modeling was used to generate predictive formulas and Bland-Altman analyses to evaluate accuracy. The majority were male (60.3%), black (81.0%), and non-Hispanic (76.7%), and 23% were ≥65 years old. After screening for multicollinearity, the best predictive model of mREE ( R 2 = 0.67) included weight, age, sex, and CRP. Two alternative models with acceptable predictability ( R 2 = 0.66) were derived with glycosylated hemoglobin or serum creatinine. Based on Bland-Altman analyses, the maintenance hemodialysis equation that included CRP had the best precision, with the highest proportion of participants' predicted energy expenditure classified as accurate (61.2%) and with the lowest number of individuals with underestimation or overestimation. This study confirms disease-specific factors as key determinants of mREE in patients on MHD and provides a preliminary predictive energy equation. Further prospective research is necessary to test the reliability and validity of this equation across diverse populations of patients who are receiving MHD.

Development of lathe tool dynamometer and finding cutting forces using negative and positive rake angle cutting tool

International Nuclear Information System (INIS)

Zeb, M.A.; Irfan, M.A.

2005-01-01

Most output parameters in machining, such as cutting forces, temperatures, strains and the work-hardening of the chip material, are directly related to the chip formation process. The characteristics of machining processes can be well understood if the forces and strains during chip formation are known. In this research a lathe tool dynamometer was used to measure cutting forces involved in machining of Steel 1045 and Aluminum 2219 T62. High Speed Steel (HSS), cutting tools with positive and negative rake angles were used. It was observed that more cutting forces are experienced by the cutting tool with positive rake angle as compared to the forces experienced by the cutting tool with negative rake angle. For steel 1045 the cutting forces using positive rake angle cutting tool were much higher. This suggested that for harder materials using a negative rake angle is more suitable for cutting. (author)

Enhancement of low power CO2 laser cutting process for injection molded polycarbonate

Science.gov (United States)

Moradi, Mahmoud; Mehrabi, Omid; Azdast, Taher; Benyounis, Khaled Y.

2017-11-01

Laser cutting technology is a non-contact process that typically is used for industrial manufacturing applications. Laser cut quality is strongly influenced by the cutting processing parameters. In this research, CO2 laser cutting specifications have been investigated by using design of experiments (DOE) with considering laser cutting speed, laser power and focal plane position as process input parameters and kerf geometry dimensions (i.e. top and bottom kerf width, ratio of the upper kerf to lower kerf, upper heat affected zone (HAZ)) and surface roughness of the kerf wall as process output responses. A 60 Watts CO2 laser cutting machine is used for cutting the injection molded samples of polycarbonate sheet with the thickness of 3.2 mm. Results reveal that by decreasing the laser focal plane position and laser power, the bottom kerf width will be decreased. Also the bottom kerf width decreases by increasing the cutting speed. As a general result, locating the laser spot point in the depth of the workpiece the laser cutting quality increases. Minimum value of the responses (top kerf, heat affected zone, ratio of the upper kerf to lower kerf, and surface roughness) are considered as optimization criteria. Validating the theoretical results using the experimental tests is carried out in order to analyze the results obtained via software.

Distinguishing butchery cut marks from crocodile bite marks through machine learning methods.

Science.gov (United States)

Domínguez-Rodrigo, Manuel; Baquedano, Enrique

2018-04-10

All models of evolution of human behaviour depend on the correct identification and interpretation of bone surface modifications (BSM) on archaeofaunal assemblages. Crucial evolutionary features, such as the origin of stone tool use, meat-eating, food-sharing, cooperation and sociality can only be addressed through confident identification and interpretation of BSM, and more specifically, cut marks. Recently, it has been argued that linear marks with the same properties as cut marks can be created by crocodiles, thereby questioning whether secure cut mark identifications can be made in the Early Pleistocene fossil record. Powerful classification methods based on multivariate statistics and machine learning (ML) algorithms have previously successfully discriminated cut marks from most other potentially confounding BSM. However, crocodile-made marks were marginal to or played no role in these comparative analyses. Here, for the first time, we apply state-of-the-art ML methods on crocodile linear BSM and experimental butchery cut marks, showing that the combination of multivariate taphonomy and ML methods provides accurate identification of BSM, including cut and crocodile bite marks. This enables empirically-supported hominin behavioural modelling, provided that these methods are applied to fossil assemblages.

Wear and breakage monitoring of cutting tools by an optical method: theory

Science.gov (United States)

Li, Jianfeng; Zhang, Yongqing; Chen, Fangrong; Tian, Zhiren; Wang, Yao

1996-10-01

An essential part of a machining system in the unmanned flexible manufacturing system, is the ability to automatically change out tools that are worn or damaged. An optoelectronic method for in situ monitoring of the flank wear and breakage of cutting tools is presented. A flank wear estimation system is implemented in a laboratory environment, and its performance is evaluated through turning experiments. The flank wear model parameters that need to be known a priori are determined through several preliminary experiments, or from data available in the literature. The resulting cutting conditions are typical of those used in finishing cutting operations. Through time and amplitude domain analysis of the cutting tool wear states and breakage states, it is found that the original signal digital specificity (sigma) 2x and the self correlation coefficient (rho) (m) can reflect the change regularity of the cutting tool wear and break are determined, but which is not enough due to the complexity of the wear and break procedure of cutting tools. Time series analysis and frequency spectrum analysis will be carried out, which will be described in the later papers.

Use of Oil-Based Mud Cutting Waste in Cement Clinker Manufacturing

OpenAIRE

Saif Al-Dhamri, H; Black, L

2014-01-01

Oil-based Mud (OBM) cutting waste is generated during the process of oil well drilling. The drilled rocks are removed from deep within the drilled well and pumped to the surface. The portion removed , known at "cutting", is a mixture of rocks, mud, water and oil. Most drilling companies store this waste in open yards with no specific treatment solution. The environmental regulations in Oman specify that storage should involve isolation, to prevent penetration of the contamination to the surfa...

CALCULATION OF LASER CUTTING COSTS

OpenAIRE

Bogdan Nedic; Milan Eric; Marijana Aleksijevic

2016-01-01

The paper presents description methods of metal cutting and calculation of treatment costs based on model that is developed on Faculty of mechanical engineering in Kragujevac. Based on systematization and analysis of large number of calculation models of cutting with unconventional methods, mathematical model is derived, which is used for creating a software for calculation costs of metal cutting. Software solution enables resolving the problem of calculating the cost of laser cutting, compar...

Method of cutting radioactivated metal structures

International Nuclear Information System (INIS)

Takimoto, Yoshinori; Sakota, Kotaro; Hamamoto, Noboru; Harada, Keizo.

1985-01-01

Purpose: To improve the cutting performance to a level as comparable with that in air, as well as prevent the scattering of the radioactive materials upon cutting to the level as that in water cutting. Method: After igniting a gas cutting torch automatically, water spray by the local water sprayer is started by the actuation of a submerged pump, while a gas cutting manipulator is operated to cut the nuclear reactor pressure vessel. In this way, cutting exhaust gases resulted from the gas cutting torch are water-washed by the spray from the local water sprayer and falls within the nuclear rector pressure vessel in the form of water streams or droplets along the inner wall surface of the pressure vessel. Further, water is fed again to the local water sprayer by the submerged pump. (Kawakami, Y.)

Effects of momentum transfer on sizing of current collectors for lithium-ion batteries during laser cutting

Science.gov (United States)

Lee, Dongkyoung; Mazumder, Jyotirmoy

2018-02-01

One of the challenges of the lithium-ion battery manufacturing process is the sizing of electrodes with good cut surface quality. Poor cut surface quality results in internal short circuits in the cells and significant heat generation. One of the solutions that may improve the cut quality with a high cutting speed is laser cutting due to its high energy concentration, fast processing time, high precision, small heat affected zone, flexible range of laser power and contact free process. In order to utilize the advantages of laser electrode cutting, understanding the physical phenomena for each material is crucial. Thus, this study focuses on the laser cutting of current collectors, such as pure copper and aluminum. A 3D self-consistent mathematical model for the laser cutting, including fluid flow, heat transfer, recoil pressure, multiple reflections, capillary and thermo-capillary forces, and phase changes, is presented and solved numerically. Simulation results for the laser cutting are analyzed in terms of penetration time, depth, width, and absorptivity, based on these selected laser parameters. In addition, melt pool flow, melt pool geometry and temperature distribution are investigated.

Age-related differences in recommended anthropometric cut-off point validity to identify cardiovascular risk factors in ostensibly healthy women.

Science.gov (United States)

Subramoney, Sreevidya; Björkelund, Cecilia; Guo, Xinxin; Skoog, Ingmar; Bosaeus, Ingvar; Lissner, Lauren

2014-12-01

To investigate validity of widely recommended anthropometric and total fat percentage cut-off points in screening for cardiovascular risk factors in women of different ages. A population-based sample of 1002 Swedish women aged 38, 50, 75 (younger, middle-aged and elderly, respectively) underwent anthropometry, health examinations and blood tests. Total fat was estimated (bioimpedance) in 670 women. Sensitivity, specificity of body mass index (BMI; ≥25 and ≥30), waist circumference (WC; ≥80 cm and ≥88 cm) and total fat percentage (TF; ≥35%) cut-off points for cardiovascular risk factors (dyslipidaemias, hypertension and hyperglycaemia) were calculated for each age. Cut-off points yielding high sensitivity together with modest specificity were considered valid. Women reporting hospital admission for cardiovascular disease were excluded. The sensitivity of WC ≥80 cm for one or more risk factors was ~60% in younger and middle-aged women, and 80% in elderly women. The specificity of WC ≥80 cm for one or more risk factors was 69%, 57% and 40% at the three ages (p < .05 for age trends). WC ≥80 cm yielded ~80% sensitivity for two or more risk factors across all ages. However, specificity decreased with increasing age (p < .0001), being 33% in elderly. WC ≥88 cm provided better specificity in elderly women. BMI and TF % cut-off points were not better than WC. Validity of recommended anthropometric cut-off points in screening asymptomatic women varies with age. In younger and middle-age, WC ≥80 cm yielded high sensitivity and modest specificity for two or more risk factors, however, sensitivity for one or more risk factor was less than optimal. WC ≥88 cm showed better validity than WC ≥80 cm in elderly. Our results support age-specific screening cut-off points for women. © 2014 the Nordic Societies of Public Health.

Laser Cutting of Thin Nickel Bellows

Science.gov (United States)

Butler, C. L.

1986-01-01

Laser cutting technique produces narrow, precise, fast, and repeatable cuts in thin nickel-allow bellows material. Laser cutting operation uses intense focused beam to melt material and assisting gas to force melted material through part thickness, creating void. When part rotated or moved longitudinally, melting and material removal continuous and creates narrow, fast, precise, and repeatable cut. Technique used to produce cuts of specified depths less than material thickness. Avoids distortion, dents, and nicks produced in delicate materials during lathe trimming operations, which require high cutting-tool pressure and holding-fixture forces.

Nutrient retention values and cooking yield factors for three South African lamb and mutton cuts.

Science.gov (United States)

van Heerden, Salomina M; Strydom, Phillip E

2017-11-01

Nutrient content of raw and cooked foods is important for formulation of healthy diets. The retention of nutrients during cooking can be influenced by various factors, including animal age, carcass characteristics and cooking method, and these factors are often unique to specific countries. Here the effects of animal age (lamb and mutton) and carcass cut (shoulder, loin and leg) combined with cooking method (moist heat and dry heat) on yield and nutrient retention of selected nutrients of South African sheep carcasses were studied. Cooking yields and moisture retention were lower for lamb loin but higher for lamb leg. Energy and fat retention were higher for all cuts of mutton compared with lamb, while higher retention values for cholesterol were recorded for lamb. Mutton retained more iron (P = 0.10) and zinc and also more vitamin B 2 , B 6 and B 12 than lamb. Shoulder cooked according to moist heat cooking method retained more magnesium, potassium and sodium. Incorporating these retention and yield values into the South African Medical Research Council's Food Composition Tables provides a reliable reference to all concerned with nutrient content of food. It will also guide practitioners and primary industry to adjust animal production aimed at optimum nutrient content to specific diets. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Numerical modelling of orthogonal cutting: application to woodworking with a bench plane.

Science.gov (United States)

Nairn, John A

2016-06-06

A numerical model for orthogonal cutting using the material point method was applied to woodcutting using a bench plane. The cutting process was modelled by accounting for surface energy associated with wood fracture toughness for crack growth parallel to the grain. By using damping to deal with dynamic crack propagation and modelling all contact between wood and the plane, simulations could initiate chip formation and proceed into steady-state chip propagation including chip curling. Once steady-state conditions were achieved, the cutting forces became constant and could be determined as a function of various simulation variables. The modelling details included a cutting tool, the tool's rake and grinding angles, a chip breaker, a base plate and a mouth opening between the base plate and the tool. The wood was modelled as an anisotropic elastic-plastic material. The simulations were verified by comparison to an analytical model and then used to conduct virtual experiments on wood planing. The virtual experiments showed interactions between depth of cut, chip breaker location and mouth opening. Additional simulations investigated the role of tool grinding angle, tool sharpness and friction.

Experimental improvement of the technology of cutting of high-pressure hoses with metal braid on hand cutting machine

OpenAIRE

Karpenko, Mykola; Bogdevicius, Marijonas; Prentkovskis, Olegas

2016-01-01

In the article the review of the problem of improvement of technology of high pressure hoses cutting on the hand cutting machines is analyzed. Different methods of cutting of high pressure hoses into the billets are overviewed and the quality of edge cuts of hoses is analyzed. The comparison of treatment on automatic cutting machines and on hand cutting machines is carried out. Different experimental techniques of improvement of the quality of edges cutting of high pressure hoses are prese...

Crystallization of glass-forming liquids: Specific surface energy

International Nuclear Information System (INIS)

Schmelzer, Jürn W. P.; Abyzov, Alexander S.

2016-01-01

A generalization of the Stefan-Skapski-Turnbull relation for the melt-crystal specific interfacial energy is developed in terms of the generalized Gibbs approach extending its standard formulation to thermodynamic non-equilibrium states. With respect to crystal nucleation, this relation is required in order to determine the parameters of the critical crystal clusters being a prerequisite for the computation of the work of critical cluster formation. As one of its consequences, a relation for the dependence of the specific surface energy of critical clusters on temperature and pressure is derived applicable for small and moderate deviations from liquid-crystal macroscopic equilibrium states. Employing the Stefan-Skapski-Turnbull relation, general expressions for the size and the work of formation of critical crystal clusters are formulated. The resulting expressions are much more complex as compared to the respective relations obtained via the classical Gibbs theory. Latter relations are retained as limiting cases of these more general expressions for moderate undercoolings. By this reason, the formulated, here, general relations for the specification of the critical cluster size and the work of critical cluster formation give a key for an appropriate interpretation of a variety of crystallization phenomena occurring at large undercoolings which cannot be understood in terms of the Gibbs’ classical treatment.

Decrease of FIB-induced lateral damage for diamond tool used in nano cutting

Energy Technology Data Exchange (ETDEWEB)

Wu, Wei [State Key Laboratory of Precision Measuring Technology and Instruments, Centre of MicroNano Manufacturing Technology, Tianjin University, Tianjin 300072 (China); Xu, Zongwei, E-mail: zongweixu@163.com [State Key Laboratory of Precision Measuring Technology and Instruments, Centre of MicroNano Manufacturing Technology, Tianjin University, Tianjin 300072 (China); Fang, Fengzhou, E-mail: fzfang@gmail.com [State Key Laboratory of Precision Measuring Technology and Instruments, Centre of MicroNano Manufacturing Technology, Tianjin University, Tianjin 300072 (China); Liu, Bing; Xiao, Yinjing; Chen, Jinping [State Key Laboratory of Precision Measuring Technology and Instruments, Centre of MicroNano Manufacturing Technology, Tianjin University, Tianjin 300072 (China); Wang, Xibin [School of Mechanical Engineering, Beijing Institute of Technology, Beijing 100081 (China); Liu, Hongzhong [State Key Laboratory for Manufacturing Systems Engineering, Xi’an Jiaotong University, Xi’an 710049 (China)

2014-07-01

Highlights: • We mainly aim to characterize and decrease the FIB-induced damage on diamond tool. • Raman and XPS methods were used to characterize the nanoscale FIB-induced damage. • Lower energy FIB can effectively lessen the FIB-induced damage on diamond tool. • The diamond tools’ performance was greatly improved after FIB process optimization. • 6 nm chip thickness of copper was achieved by diamond tool with 22 nm edge radius. - Abstract: Diamond cutting tools with nanometric edge radius used in ultra-precision machining can be fabricated by focused ion beam (FIB) technology. However, due to the nanoscale effects, the diamond tools performance and the cutting edge lifetime in nano cutting would be degraded because of the FIB-induced nanoscale lateral damage. In this study, the methods of how to effectively characterize and decrease the FIB-induced lateral damage for diamond tool are intensively studied. Based on the performance optimization diamond machining tools, the controllable chip thickness of less than 10 nm was achieved on a single-crystal copper in nano cutting. In addition, the ratio of minimum thickness of chip (MTC) to tool edge radius of around 0.3–0.4 in nano cutting is achieved. Methods for decreasing the FIB-induced damage on diamond tools and adding coolant during the nano cutting are very beneficial in improving the research of nano cutting and MTC. The nano cutting experiments based on the sharp and high performance of diamond tools would validate the nano cutting mechanisms that many molecular dynamic simulation studies have put forward and provide new findings for nano cutting.

Cut-off parameters in the one-dimensional two-fermion model

International Nuclear Information System (INIS)

Apostol, M.

1982-07-01

It is shown that the usual cut-off procedure (α cut-off parameter) employed in the boson representation of the fermion field opepators of the one-djmensional two-fermion model (TFM) is an incorrect one as the computator of the hermitean-conjugate field operators at the same space-point fails to fulfil a certain relationship which was pointed out long ago by Jordan. The complete form of the boson representation (including the zero-mode) of a single fermion field and the correct values of the cut-off parameter α is reviewed following Jordan and generalized to the TFM. The cut-off parameter α corresponds to a bandwidth cut-off and Jordan's boson representation is exact only in the limit α → 0. The additional zero-mode terms make the exact solution of the backscattering and umklapp scattering problem to be valid only if a supplementary condition is imposed on the coupling constants. Using the present bosonization technique all the inconsistencies of the TFM are removed. The one-particle Green's function and response functions of the Tomonaga-Luttinger model (TLM) are calculated and found to be identical with those obtained by direct diagram summation. The energy gap appearing in the spectrum of the TFM with backscattering and umklapp scattering for certain values of the coupling constants is shown to be proportional to the momentum transfer cut-off γ -1 which has to be kept finite while α goes to zero. Under such conditions the anticommunication relations and Jordan's commutator are invariant under the canonical transformation on the boson operators that diagonalizes the Hamiltonian of the TLM. The charge-density response function of the TFM with backscattering is perturbationally calculated up to the first order. The cut-off α -1 applies in the same way to terms which differ only by their spin indices in the expression of this response function. The charge-density response function is also evaluated at low frequencies for the exactly soluble TFM with

The impact of cuts in legal aid funding on charities.

Science.gov (United States)

Morris, Debra; Barr, Warren

2013-03-01

This article focusses on the specific impact of the cuts in legal aid funding on the charitable sector. The sector plays a significant role in advice giving. Some charities have the provision of legal advice as their sole purpose, whilst the work of other charities includes the giving of legal advice. Funding comes via a number of sources including legal aid, local authorities and charitable trusts. Whilst this volume highlights the legal aid reforms that will lead to significant cuts in funding, this article notes that charitable providers of legal advice have also suffered major cuts from their other traditional funding sources. Against this background, the article considers the serious and often unforeseen consequences for charities of the legal aid reforms, which go far beyond the impact on the high street law firm and access to justice for claimants.

Evaluating optical hazards from plasma arc cutting.

Science.gov (United States)

Glassford, Eric; Burr, Gregory

2018-01-01

The Health Hazard Evaluation Program of the National Institute for Occupational Safety and Health evaluated a steel building materials manufacturer. The employer requested the evaluation because of concerns about optical radiation hazards from a plasma arc cutting system and the need to clarify eye protection requirements for plasma operators, other employees, and visitors. The strength of the ultraviolet radiation, visible radiation (light), and infrared radiation generated by the plasma arc cutter was measured at various distances from the source and at different operating amperages. Investigators also observed employees performing the plasma arc cutting. Optical radiation above safe levels for the unprotected eyes in the ultraviolet-C, ultraviolet-B, and visible light ranges were found during plasma arc cutting. In contrast, infrared and ultraviolet-A radiation levels during plasma arc cutting were similar to background levels. The highest non-ionizing radiation exposures occurred when no welding curtains were used. A plasma arc welding curtain in place did not eliminate optical radiation hazards to the plasma arc operator or to nearby employees. In most instances, the measured intensities for visible light, UV-C, and UV-B resulted in welding shade lens numbers that were lower than those stipulated in the OSHA Filter Lenses for Protection Against Radiant Energy table in 29 CFR 1910.133(a)(5). [1] Investigators recommended using a welding curtain that enclosed the plasma arc, posting optical radiation warning signs in the plasma arc cutter area, installing audible or visual warning cues when the plasma arc cutter was operating, and using welding shades that covered the plasma arc cutter operator's face to protect skin from ultraviolet radiation hazards.

Laser cutting of various materials: Kerf width size analysis and life cycle assessment of cutting process

Science.gov (United States)

Yilbas, Bekir Sami; Shaukat, Mian Mobeen; Ashraf, Farhan

2017-08-01

Laser cutting of various materials including Ti-6Al-4V alloy, steel 304, Inconel 625, and alumina is carried out to assess the kerf width size variation along the cut section. The life cycle assessment is carried out to determine the environmental impact of the laser cutting in terms of the material waste during the cutting process. The kerf width size is formulated and predicted using the lump parameter analysis and it is measured from the experiments. The influence of laser output power and laser cutting speed on the kerf width size variation is analyzed using the analytical tools including scanning electron and optical microscopes. In the experiments, high pressure nitrogen assisting gas is used to prevent oxidation reactions in the cutting section. It is found that the kerf width size predicted from the lump parameter analysis agrees well with the experimental data. The kerf width size variation increases with increasing laser output power. However, this behavior reverses with increasing laser cutting speed. The life cycle assessment reveals that material selection for laser cutting is critical for the environmental protection point of view. Inconel 625 contributes the most to the environmental damages; however, recycling of the waste of the laser cutting reduces this contribution.

Cutting costs without drawing blood.

Science.gov (United States)

Copeland, T

2000-01-01

When looking for ways to cut costs, most managers reach for the head-count hatchet, and the markets usually roar with approval. But a company can almost always create far more sustainable value by rigorously evaluating the small-ticket capital items that often get rubber-stamped. Drawing on his experience as a consultant and providing numerous anecdotes, the author contends that those "little" requests often prove to be gold plated or unnecessary. A disciplined evaluation involves asking only eight questions and conducting postmortems--regular audits of units' capital spending. But the payoff is enormous. Because cutting the capital budget increases cash flow, the author argues that a permanent cut of just 15% in the planned level of capital spending could boost some companies' market capitalization by as much as 30%. The first three questions--Is this your investment to make? Does it really have to be new? How are our competitors meeting compliance needs?--are asked of operating managers as they assemble capital project requests. The next three are asked by senior managers of themselves and their colleagues as they examine proposals: Is the left hand duplicating investments made by the right? Are trade-offs between profit and capital spending well understood? Are there signs of budget massage? At the end of the review process, senior managers ask: Are we fully using shared assets? How fine-grained are our capacity measures? The author's suggestions for the postmortem include searching for systematic problems with whole classes of expenditures and making sure audit teams come up with specific recommendations for change.

Energy flow in high speed perforation and cutting

International Nuclear Information System (INIS)

van Thiel, M.

1980-01-01

It is demonstrated that effects of long rod penetrators on targets can be modeled by introducing a high pressure (energy) column on the penetration path in place of the projectile. This energy can be obtained from the kinetic energy of the penetrator; the equations of state of the materials used and a Bernoulli penetration condition. The model is supported by detailed hydro calculations

Logging potentials and energy wood resources in southern Finland; Potentiaaliset hakkuumahdollisuudet ja energiapuuvarat Etelae- Suomessa

Energy Technology Data Exchange (ETDEWEB)

Pesonen, M; Malinen, J [Finnish Forest Research Inst. METLA, Vantaa (Finland)

1997-12-01

Development of energy wood resources in Southern Finland over the next 40 years was studied on the basis of four cutting scenarios. Development of energy wood accrual was considered on the production cost levels of FIM 45/MWh and FIM 55/MWh in scenarios describing sustainable cutting potential, long-term cutting plans of forest owners and cutting of industrial mechandable wood over the years of depression. Effects of limitations concerning energy wood harvesting from meagre forest land and bogs on the energy wood accruals of sustainable cutting potential were also studied. The energy wood potential in Southern Finland was estimated at 3.6 million m{sup 3}/a on the production cost level of FIM 45/MWh. The energy wood accrual equal to sustainable cutting potential was 70 % of the energy wood potential. The energy wood potential increased to 8.8 m{sup 3}/a when the production cost level increased to FIM 55/MWh, the energy wood accrual of sustainable cutting potential being 51 %. The energy wood accruals according to felling plans of forest owners and cuttings over the years of depression were smaller than that of sustainable cutting potential, due to smaller loggings. Limitation of energy wood harvesting from meagre forest land and bogs would reduce the energy wood accrual of sustainable cutting potential by 22 %. This would involve a reduction of one million m{sup 3} in the harvesting potential. The energy wood accrual of sustainable cutting potential in Finland was 5.8 million m{sup 3}/a on the production cost level of FIM 55/MWh. This is equal to the aim set by the BIOENERGY Research Programme for the use potential of 1 Mtoe (equivalent oil tonne) on the production cost level of FIM 45/MWh

The performance characteristics of prostate-specific antigen and prostate-specific antigen density in Chinese men.

Science.gov (United States)

Teoh, Jeremy Yc; Yuen, Steffi Kk; Tsu, James Hl; Wong, Charles Kw; Ho, Brian Sh; Ng, Ada Tl; Ma, Wai-Kit; Ho, Kwan-Lun; Yiu, Ming-Kwong

2017-01-01

We investigated the performance characteristics of prostate-specific antigen (PSA) and PSA density (PSAD) in Chinese men. All Chinese men who underwent transrectal ultrasound-guided prostate biopsy (TRUS-PB) from year 2000 to 2013 were included. The receiver operating characteristic (ROC) curves for both PSA and PSAD were analyzed. The sensitivity, specificity, positive predictive value (PPV) and negative predictive value (NPV) at different cut-off levels were calculated. A total of 2606 Chinese men were included. For the ROC, the area under curve was 0.770 for PSA (P specificity of 14.1%, PPV of 29.5%, and NPV of 86.9%; PSAD of 0.12 ng ml-1 cc-1 had sensitivity of 94.5%, specificity of 26.6%, PPV of 32.8%, and NPV of 92.7%. On multivariate logistic regression analyses, PSA cut-off at 4.5 ng ml-1 (OR 1.61, 95% CI 1.05-2.45, P= 0.029) and PSAD cut-off at 0.12 ng ml-1 cc-1 (OR 6.22, 95% CI 4.20-9.22, Pprostate cancer detection on TRUS-PB. In conclusion, the performances of PSA and PSAD at different cut-off levels in Chinese men were very different from those in Caucasians. PSA of 4.5 ng ml-1 and PSAD of 0.12 ng ml-1 cc-1 had near 95% sensitivity and were significant predictors of prostate cancer detection in Chinese men.

Energy transfer and visible-infrared quantum cutting photoluminescence modification in Tm-Yb codoped YPO(4) inverse opal photonic crystals.

Science.gov (United States)

Wang, Siqin; Qiu, Jianbei; Wang, Qi; Zhou, Dacheng; Yang, Zhengwen

2015-08-01

YPO4:  Tm, Yb inverse opal photonic crystals were successfully synthesized by the colloidal crystal templates method, and the visible-infrared quantum cutting (QC) photoluminescence properties of YPO4:  Tm, Yb inverse opal photonic crystals were investigated. We obtained tetragonal phase YPO4 in all the samples when the samples sintered at 950°C for 5 h. The visible emission intensity of Tm3+ decreased significantly when the photonic bandgap was located at 650 nm under 480 nm excitation. On the contrary, the QC emission intensity of Yb3+ was enhanced as compared with the no photonic bandgap sample. When the photonic bandgap was located at 480 nm, the Yb3+ and Tm3+ light-emitting intensity weakened at the same time. We demonstrated that the energy transfer between Tm3+ and Yb3+ is enhanced by the suppression of the red emission of Tm3+. Additionally, the mechanisms for the influence of the photonic bandgap on the energy transfer process of the Tm3+, Yb3+ codoped YPO4 inverse opal are discussed.

Practical side of cutting. Part 3. ; CO2 laser cutting. Setsudan gijutsu no jissai. 3. ; Laser setsudan

Energy Technology Data Exchange (ETDEWEB)

Miyazaki, T.; Shinonaga, H. (Toshiba Corp., Tokyo (Japan))

1993-03-05

The nature peculiar to laser beam makes it difficult to understand the phenomena in laser cutting. Quoting an example of cutting steel materials, practical minimum basic subjects, factors governing the cutting phenomena with points to be considered, and the current state of the technology are outlined. Various kinds of expert systems and automatic programming devices have been placed on the market to make NC input easier in laser cutting. Shape accuracy, cutting quality, cutting speed, applicable plate thickness, etc. are among the subjects required for laser cutting. The factors are the method of scanning, characteristics of laser beam, work, machining conditions, etc. The factors obstructing stable processing are the change in the ambient temperature, humidity, dust, oil mist, vibration, etc. The basic factors which control the laser cutting are the power density and its distribution at the working point. Pulse cutting is employed when continuous laser heat input is not appropriate. Summarized report is made on the focal point and assist gas. 16 refs., 9 figs., 1 tab.

Ultralight Cut-Paper-Based Self-Charging Power Unit for Self-Powered Portable Electronic and Medical Systems.

Science.gov (United States)

Guo, Hengyu; Yeh, Min-Hsin; Zi, Yunlong; Wen, Zhen; Chen, Jie; Liu, Guanlin; Hu, Chenguo; Wang, Zhong Lin

2017-05-23

The development of lightweight, superportable, and sustainable power sources has become an urgent need for most modern personal electronics. Here, we report a cut-paper-based self-charging power unit (PC-SCPU) that is capable of simultaneously harvesting and storing energy from body movement by combining a paper-based triboelectric nanogenerator (TENG) and a supercapacitor (SC), respectively. Utilizing the paper as the substrate with an assembled cut-paper architecture, an ultralight rhombic-shaped TENG is achieved with highly specific mass/volume charge output (82 nC g -1 /75 nC cm -3 ) compared with the traditional acrylic-based TENG (5.7 nC g -1 /5.8 nC cm -3 ), which can effectively charge the SC (∼1 mF) to ∼1 V in minutes. This wallet-contained PC-SCPU is then demonstrated as a sustainable power source for driving wearable and portable electronic devices such as a wireless remote control, electric watch, or temperature sensor. This study presents a potential paper-based portable SCPU for practical and medical applications.

Experimental study of the effect of gas nature on plasma arc cutting of mild steel

Czech Academy of Sciences Publication Activity Database

Kavka, Tetyana; Mašláni, Alan; Hrabovský, Milan; Křenek, Petr; Stehrer, T.; Pauser, H.

2013-01-01

Roč. 46, č. 22 (2013), s. 224011-224011 ISSN 0022-3727 R&D Projects: GA ČR GAP205/11/2070 Institutional support: RVO:61389021 Keywords : Arc cutting * steam plasma cutting * energy balance Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 2.521, year: 2013 http://iopscience.iop.org/0022-3727/46/22/224011/pdf/0022-3727_46_22_224011.pdf

Cutting Cosmos

DEFF Research Database (Denmark)

Mikkelsen, Henrik Hvenegaard

For the first time in over 30 years, a new ethnographic study emerges on the Bugkalot tribe, more widely known as the Ilongot of the northern Philippines. Exploring the notion of masculinity among the Bugkalot, Cutting Cosmos is not only an experimental, anthropological study of the paradoxes...... around which Bugkalot society revolves, but also a reflection on anthropological theory and writing. Focusing on the transgressive acts through which masculinity is performed, this book explores the idea of the cosmic cut, the ritual act that enables the Bugkalot man to momentarily hold still the chaotic...

Latest development of laser cutting

OpenAIRE

Wetzig, Andreas; Herwig, Patrick; Hauptmann, Jan; Goppold, Cindy; Baumann, Robert; Fürst, Andreas; Rose, Michael; Pinder, Thomas; Mahrle, Achim; Beyer, Eckhard

2016-01-01

Laser cutting was one of the first applications of laser material processing. Today, laser cutting is the most widespread application among laser material processing besides laser marking. Meanwhile, nearly each material can be cut by means of a laser, in particular since ultra short pulse lasers are available in the power range of up to 100 W. The to be cut material can come with thicknesses from a few microns till tens of millimeters as flat stock or as free form shapes. The paper will conc...

Dimming LEDs with Phase-Cut Dimmers: The Specifier's Process for Maximizing Success

Energy Technology Data Exchange (ETDEWEB)

Miller, Naomi J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Poplawski, Michael E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2013-10-01

This report reviews how phase-cut dimmers work, how LEDs differ from the incandescent lamps that the dimmers were historically designed to control, and how these differences can lead to complications when trying to dim LEDs. Compatibility between a specific LED source and a specific phase-cut dimmer is often unknown and difficult to assess, and ensuring compatibility adds complexity to the design, specification, bidding, and construction observation phases for new buildings and major remodel projects. To maximize project success, this report provides both general guidance and step-by-step procedures for designing phase-controlled LED dimming on both new and existing projects, as well as real-world examples of how to use those procedures.

Optimised cut-off function for Tersoff-like potentials for a BN nanosheet: a molecular dynamics study

International Nuclear Information System (INIS)

Kumar, Rajesh; Rajasekaran, G; Parashar, Avinash

2016-01-01

In this article, molecular dynamics based simulations were carried out to study the tensile behaviour of boron nitride nanosheets (BNNSs). Four different sets of Tersoff potential parameters were used in the simulations for estimating the interatomic interactions between boron and nitrogen atoms. Modifications were incorporated in the Tersoff cut-off function to improve the accuracy of results with respect to fracture stress, fracture strain and Young’s modulus. In this study, the original cut-off function was optimised in such a way that small and large cut-off distances were made equal, and hence a single cut-off distance was used with all sets of Tersoff potential parameters. The single value of cut-off distance for the Tersoff potential was chosen after analysing the potential energy and bond forces experienced by boron and nitrogen atoms subjected to bond stretching. The simulations performed with the optimised cut-off function help in identifying the Tersoff potential parameters that reproduce the experimentally evaluated mechanical behaviour of BNNSs. (paper)

CALCULATION OF LASER CUTTING COSTS

Directory of Open Access Journals (Sweden)

Bogdan Nedic

2016-09-01

Full Text Available The paper presents description methods of metal cutting and calculation of treatment costs based on model that is developed on Faculty of mechanical engineering in Kragujevac. Based on systematization and analysis of large number of calculation models of cutting with unconventional methods, mathematical model is derived, which is used for creating a software for calculation costs of metal cutting. Software solution enables resolving the problem of calculating the cost of laser cutting, comparison' of costs made by other unconventional methods and provides documentation that consists of reports on estimated costs.

Simulation of Temperature Field Distribution for Cutting the Temperated Glass by Ultraviolet Laser

Science.gov (United States)

Yang, B. J.; He, Y. C.; Dai, F.; Lin, X. C.

2017-03-01

The finite element software ANSYS was adopted to simulate the temperature field distribution for laser cutting tempered glass, and the influence of different process parameters, including laser power, glass thickness and cutting speed, on temperature field distribution was studied in detail. The results show that the laser power has a greater influence on temperature field distribution than other paremeters, and when the laser power gets to 60W, the highest temperature reaches 749°C, which is higher than the glass softening temperature. It reflects the material near the laser spot is melted and the molten slag is removed by the high-energy water beam quickly. Finally, through the water guided laser cutting tempered glass experiment the FEM theoretical analysis was verified.

Tubing and cable cutting tool

Science.gov (United States)

Mcsmith, D. D.; Richardson, J. I. (Inventor)

1984-01-01

A hand held hydraulic cutting tool was developed which is particularly useful in deactivating ejection seats in military aircraft rescue operations. The tool consists primarily of a hydraulic system composed of a fluid reservoir, a pumping piston, and an actuator piston. Mechanical cutting jaws are attached to the actuator piston rod. The hydraulic system is controlled by a pump handle. As the pump handle is operated the actuator piston rod is forced outward and thus the cutting jaws are forced together. The frame of the device is a flexible metal tubing which permits easy positioning of the tool cutting jaws in remote and normally inaccessible locations. Bifurcated cutting edges ensure removal of a section of the tubing or cable to thereby reduce the possibility of accidental reactivation of the tubing or cable being severed.

Cutting concrete with abrasion jet

International Nuclear Information System (INIS)

Yie, G.G.

1982-01-01

Fluidyne Corporation has developed a unique process and apparatus that allow selected abrasives to be introduced into high-speed waterjet to produce abrasive-entrained waterjet that has high material-cutting capabilities, which is termed by Fluidyne as the Abrasion Jet. Such Abrasion Jet has demonstrated capability in cutting hard rock and concrete at a modest pressure of less than 1360 bars (20,000 psi) and a power input of less than 45 kW (60 horsepower). Abrasion Jet cutting of concrete is characterized by its high rate of cutting, flexible operation, good cut quality, and relatively low costs. This paper presents a general description of this technology together with discussions of recent test results and how it could be applied to nuclear decontamination and decommissioning work. 8 references

Influence of cutting parameters on the depth of subsurface deformed layer in nano-cutting process of single crystal copper.

Science.gov (United States)

Wang, Quanlong; Bai, Qingshun; Chen, Jiaxuan; Su, Hao; Wang, Zhiguo; Xie, Wenkun

2015-12-01

Large-scale molecular dynamics simulation is performed to study the nano-cutting process of single crystal copper realized by single-point diamond cutting tool in this paper. The centro-symmetry parameter is adopted to characterize the subsurface deformed layers and the distribution and evolution of the subsurface defect structures. Three-dimensional visualization and measurement technology are used to measure the depth of the subsurface deformed layers. The influence of cutting speed, cutting depth, cutting direction, and crystallographic orientation on the depth of subsurface deformed layers is systematically investigated. The results show that a lot of defect structures are formed in the subsurface of workpiece during nano-cutting process, for instance, stair-rod dislocations, stacking fault tetrahedron, atomic clusters, vacancy defects, point defects. In the process of nano-cutting, the depth of subsurface deformed layers increases with the cutting distance at the beginning, then decreases at stable cutting process, and basically remains unchanged when the cutting distance reaches up to 24 nm. The depth of subsurface deformed layers decreases with the increase in cutting speed between 50 and 300 m/s. The depth of subsurface deformed layer increases with cutting depth, proportionally, and basically remains unchanged when the cutting depth reaches over 6 nm.

THE HYDROLOGIC RESPONSE OF A SMALL CATCHMENT TO CLEAR-CUTTING

Science.gov (United States)

We simulated how a landscape disturbance (e.g., fire or clear-cutting) alters hillslope and catchment hydrologic processes. Specifically, we simulated how the pattern and magnitude of tree removal in a catchment increases downslope transport of water and alters catchment soil moi...

ADVANCED CUTTINGS TRANSPORT STUDY

Energy Technology Data Exchange (ETDEWEB)

Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Mengjiao Yu; Ramadan Ahmed; Mark Pickell; Len Volk; Lei Zhou; Zhu Chen; Aimee Washington; Crystal Redden

2003-09-30

The Quarter began with installing the new drill pipe, hooking up the new hydraulic power unit, completing the pipe rotation system (Task 4 has been completed), and making the SWACO choke operational. Detailed design and procurement work is proceeding on a system to elevate the drill-string section. The prototype Foam Generator Cell has been completed by Temco and delivered. Work is currently underway to calibrate the system. Literature review and preliminary model development for cuttings transportation with polymer foam under EPET conditions are in progress. Preparations for preliminary cuttings transport experiments with polymer foam have been completed. Two nuclear densitometers were re-calibrated. Drill pipe rotation system was tested up to 250 RPM. Water flow tests were conducted while rotating the drill pipe up to 100 RPM. The accuracy of weight measurements for cuttings in the annulus was evaluated. Additional modifications of the cuttings collection system are being considered in order to obtain the desired accurate measurement of cuttings weight in the annular test section. Cutting transport experiments with aerated fluids are being conducted at EPET, and analyses of the collected data are in progress. The printed circuit board is functioning with acceptable noise level to measure cuttings concentration at static condition using ultrasonic method. We were able to conduct several tests using a standard low pass filter to eliminate high frequency noise. We tested to verify that we can distinguish between different depths of sand in a static bed of sand. We tested with water, air and a mix of the two mediums. Major modifications to the DTF have almost been completed. A stop-flow cell is being designed for the DTF, the ACTF and Foam Generator/Viscometer which will allow us to capture bubble images without the need for ultra fast shutter speeds or microsecond flash system.

Energy [r]evolution - a sustainable world energy outlook

NARCIS (Netherlands)

Teske, S.; Muth, J.; Sawyer, S.; Pregger, T.; Simon, S.; Naegler, T.; O'Sullivan, M.; Schmid, S; Pagenkopf, J.; Frieske, B.; Graus, W.H.J.; Kermeli, K.; Zittel, W.; Rutovitz, J.; Harris, S.; Ackermann, T.; Ruwahata, R.; Martense, N.

2012-01-01

Energy [R]evolution 2012 provides a consistent fundamental pathway for how to protect our climate: getting the world from where we are now to where we need to be by phasing out fossil fuels and cutting CO2 emissions while ensuring energy security.The Energy [R]evolution Scenario has become a well

Intramolecular energy transfer and mode-specific effects in unimolecular reactions of 1,2-difluoroethane

Science.gov (United States)

Raff, Lionel M.

1989-06-01

The unimolecular decomposition reactions of 1,2-difluoroethane upon mode-specific excitation to a total internal energy of 7.5 eV are investigated using classical trajectory methods and a previously formulated empirical potential-energy surface. The decomposition channels for 1,2-difluoroethane are, in order of importance, four-center HF elimination, C-C bond rupture, and hydrogen-atom dissociation. This order is found to be independent of the particular vibrational mode excited. Neither fluorine-atom nor F2 elimination reactions are ever observed even though these dissociation channels are energetically open. For four-center HF elimination, the average fraction of the total energy partitioned into internal HF motion varies between 0.115-0.181 depending upon the particular vibrational mode initially excited. The internal energy of the fluoroethylene product lies in the range 0.716-0.776. Comparison of the present results with those previously obtained for a random distribution of the initial 1,2-difluoroethane internal energy [J. Phys. Chem. 92, 5111 (1988)], shows that numerous mode-specific effects are present in these reactions in spite of the fact that intramolecular energy transfer rates for this system are 5.88-25.5 times faster than any of the unimolecular reaction rates. Mode-specific excitation always leads to a total decomposition rate significantly larger than that obtained for a random distribution of the internal energy. Excitation of different 1,2-difluoroethane vibrational modes is found to produce as much as a 51% change in the total decomposition rate. Mode-specific effects are also seen in the product energy partitioning. The rate coefficients for decomposition into the various channels are very sensitive to the particular mode excited. A comparison of the calculated mode-specific effects with the previously determined mode-to-mode energy transfer rate coefficients [J. Chem. Phys. 89, 5680 (1988)] shows that, to some extent, the presence of mode-specific

Influence of shear cutting parameters on the fatigue behavior of a dual-phase steel

Science.gov (United States)

Paetzold, I.; Dittmann, F.; Feistle, M.; Golle, R.; Haefele, P.; Hoffmann, H.; Volk, W.

2017-09-01

The influence of the edge condition of car body and chassis components made of steel sheet on fatigue behavior under dynamic loading presents a major challenge for automotive manufacturers and suppliers. The calculated lifetime is based on material data determined by the fatigue testing of specimens with polished edges. Prototype components are often manufactured by milling or laser cutting, whereby in practice, the series components are produced by shear cutting due to its cost-efficiency. Since the fatigue crack in such components usually starts from a shear cut edge, the calculated and experimental determined lifetime will vary due to the different conditions at the shear cut edges. Therefore, the material data determined with polished edges can result in a non-conservative component design. The aim of this study is to understand the relationship between the shear cutting process and the fatigue behavior of a dual-phase steel sheet. The geometry of the shear cut edge as well as the depth and degree of work hardening in the shear affected zone can be adjusted by using specific shear cutting parameters, such as die clearance and cutting edge radius. Stress-controlled fatigue tests of unnotched specimens were carried out to compare the fatigue behavior of different edge conditions. By evaluating the results of the fatigue experiments, influential shear cutting parameters on fatigue behavior were identified. It was possible to assess investigated shear cutting strategies regarding the fatigue behavior of a high-strength steel DP800.

Using internally cooled cutting tools in the machining of difficult-to-cut materials based on Waspaloy

Directory of Open Access Journals (Sweden)

Yahya Isik

2016-05-01

Full Text Available Nickel-based superalloys such as Waspaloy are used for engine components and in the nuclear industry, where considerable strength and corrosion resistance at high operating temperatures are called for. These characteristics of such alloys cause increases in cutting temperature and resultant tool damage, even at low cutting speeds and low feed rates. Thus, they are classified as difficult-to-cut materials. This article presents a cooling method to be used in metal cutting based on a tool holder with a closed internal cooling system with cooling fluid circulating inside. Hence, a green cooling method that does not harm the environment and is efficient in removing heat from the cutting zone was developed. A series of cutting experiments were conducted to investigate the practicality and effectiveness of the internally cooled tool model. The developed system achieved up to 13% better surface quality than with dry machining, and tool life was extended by 12%. The results clearly showed that with the reduced cutting temperature of the internal cooling, it was possible to control the temperature and thus prevent reaching the critical cutting temperature during the turning process, which is vitally important in extending tool life during the processing of Waspaloy.

FY 2000 report on the results of the technology development of energy use reduction of machine tools. Development of dry cutting use abrasion resistant/lubricous coated tools; 2000 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Dry sessakuyo taimamo junkatsusei hifuku kogu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of energy conservation and reduction of environmental loads of machine tools, study was conducted on the dry cutting which is the cutting with no use of cutting oil, and the FY 2000 results were summed up. The study was made on dry cutting use abrasion resistance/lubricous coated tools coated with the composite membrane of which the cutting life become little lower than that of existing tools using coolant. In the survey of abrasion resistant/lubricous films, it was found out that in the adhesion to ultra-hard substrates, the DLC single-layer film consisting only of carbon indicated the same excellent adhesion as intermediate-layer inserts. As to the synthesis of abrasion resistant/lubricous films, the synthesis of the composite membrane (WC/C membrane) consisting of tungsten carbide (WC) and carbon (C) was made using arc ion plating device. The WC/C membrane is composed of W and C and has the structure in which at nm levels the layer with much W and the layer with less W were alternately piled. Study was made of devices necessary for the development of abrasion resistant/lubricous films and the film formation for drill. (NEDO)

Laser Cutting, Development Trends

DEFF Research Database (Denmark)

Olsen, Flemming Ove

1999-01-01

In this paper a short review of the development trends in laser cutting will be given.The technology, which is the fastest expanding industrial production technology will develop in both its core market segment: Flat bed cutting of sheet metal, as it will expand in heavy industry and in cutting...... of 3-dimensional shapes.The CO2-laser will also in the near future be the dominating laser source in the market, although the new developments in ND-YAG-lasers opens for new possibilities for this laser type....

Water-Cut Sensor System

KAUST Repository

Karimi, Muhammad Akram; Shamim, Atif; Arsalan, Muhammad

2018-01-01

Provided in some embodiments is a method of manufacturing a pipe conformable water-cut sensors system. Provided in some embodiments is method for manufacturing a water-cut sensor system that includes providing a helical T-resonator, a helical ground

Effects of cutting and maturity on antioxidant activity of fresh-cut tomatoes

NARCIS (Netherlands)

Moreira Lana, M.; Tijskens, L.M.M.; Kooten, van O.

2005-01-01

To investigate the changes in total antioxidant activity of fresh-cut tomato during storage, tomato fruits harvested at three different stages of maturity were cut into 7-mm thick slices and stored at 5°C. Intact (control) fruits were stored in the same conditions. The antioxidant activity was

Quality Analysis of Cutting Steel Using Laser

Directory of Open Access Journals (Sweden)

Vladislav Markovič

2013-02-01

Full Text Available The article explores the quality dependence of the edge surface of steel C45 LST EN 10083-1 obtained cutting the material using laser on different cutting regimes and variations in the thickness of trial steel. The paper presents the influence of the main modes of laser cutting equipment Trulaser 3030, including cutting speed, pressure, angle and the thickness of the surface on the quality characteristics of the sample. The quality of the edge after laser cutting is the most important indicator influencing such technological spread in industry worldwide. Laser cutting is the most popular method of material cutting. Therefore, the article focuses on cutting equipment, cutting defects and methods of analysis. Research on microstructure, roughness and micro-toughness has been performed with reference to edge samples. At the end of the publication, conclusions are drawn.Article in Lithuanian

Quality Analysis of Cutting Steel Using Laser

Directory of Open Access Journals (Sweden)

Vladislav Markovič

2012-12-01

Full Text Available The article explores the quality dependence of the edge surface of steel C45 LST EN 10083-1 obtained cutting the material using laser on different cutting regimes and variations in the thickness of trial steel. The paper presents the influence of the main modes of laser cutting equipment Trulaser 3030, including cutting speed, pressure, angle and the thickness of the surface on the quality characteristics of the sample. The quality of the edge after laser cutting is the most important indicator influencing such technological spread in industry worldwide. Laser cutting is the most popular method of material cutting. Therefore, the article focuses on cutting equipment, cutting defects and methods of analysis. Research on microstructure, roughness and micro-toughness has been performed with reference to edge samples. At the end of the publication, conclusions are drawn.Article in Lithuanian

Cutting of Control Rod Guide Tubes and Jet Pumps at Wuergassen NPP/ Germany

International Nuclear Information System (INIS)

Ralf Loock

2006-01-01

KWW Nuclear Power Plant has been erected and put into operation in the time period 1968 to end of 1971. In 23 years of operation about 73 billions kWh electric power have been generated. The electric rated power was 670 MW. In May 1995 the decommission was started for economical reasons, since April 1997 the demolition is in progress. In autumn 2003 FANP has been called upon to cut the Control Rod Guide Tubes and Jet Pumps. After a 10 months preparatory phase, cutting of the Control Rod Guide Tubes and Jet Pumps was started in September 2004. For radiation protection reasons the Control Rod Guide Tubes and Jet Pumps were cut and packed remote controlled under water. The cutting process had been selected particularly under consideration of radiation protection aspects. A combination of the technologies band sawing and nibbling was assigned for cutting of the Control Rod Guide Tubes and Jet Pumps. The band saw consists of a substructure and of a feed system installed on it. The feed system can be equipped with one or two band saws optionally. A turntable is integrated in the substructure. It is used to support the CRGT respectively the residual piece of the CRGT and to move it out of the cut position after finishing the cutting. After getting the agreement to the specification, the equipment has been designed and manufactured according to the specification preferences. After finishing the internal testing, the factory acceptance test as well as acceptance and functional tests of every facility were carried out. After cold testing being performed successfully, the cutting equipment was installed in the NPP and checked for operational safety additionally. Cutting of the Control Rod Guide Tubes and Jet Pumps has been carried out on two working places inside the fuel element storage pool. During the total project duration on site the processing has been supervised by the radiation protection staff permanently. As a result 110 Control Rod Guide Tubes and 18 Jet Pumps were

Effect of cutting medium temperatures on rooting process and root primordium differentiation of hardwood cuttings of tetraploid robinia pseudoacacia cutting medium temperatures of tetraploid robinia pseudoacacia

International Nuclear Information System (INIS)

Ling, W.X.; Jine, Q.; Zhong, Z.

2014-01-01

In this study, to examine the effect of heat treatment on the rooting and root development of hardwood cuttings of the tetraploid Robinia pseudoacacia, cuttings of 1-year-old stems were taken from 3-year-old mother trees and treated with IBA solution (1000 mg/L) for 6 h, with water was as a control. Treated cuttings were rooted in heated or unheated nursery beds. Samples were collected on day ten after planting, and then for every five days. The bases of the cuttings were embedded in paraffin and sectioned before being examined under a microscope to determine whether there had been any morphological changes. We found no root primordia in the tissues of the hardwood cuttings of the tetraploid Robinia pseudoacacia before cutting. In the heated bed, adventitious roots originated from callus tissue and the junction between the pith rays and cortical parenchyma cells, and in the unheated bed, adventitious roots originated only from callus tissue. The rooting process involved callus formation, adventitious root formation and elongation; rooting occurred 5-7 days earlier in the heated cuttings than in the unheated ones, and rooting rates were significantly higher in the former 30 days and 50 days after cutting; the minimum effective accumulated temperatures for these three stages were 109.25 degree C, 211.68 degree C and 301.38 degree C, respectively. Our results revealed that heating the soil can promote adventitious root formation, speed up the rooting rate, and cut the propagation period of the tetraploid Robinia pseudoacacia. (author)

Using Grass Cuttings from Sports Fields for Anaerobic Digestion and Combustion

Directory of Open Access Journals (Sweden)

Meike Nitsche

2017-03-01

Full Text Available Sports fields provide a recreation space for citizens, but also generate grass biomass, which is cut weekly during the main seasons and therefore could be used in energy generation (combustion or anaerobic digestion. To evaluate the technical suitability of the grass cuttings, silage was produced from four sports fields during one vegetation period and investigated for relevant properties. Potential methane yield was determined with batch tests. Mean methane yield was 291.86 lN·kg−1 VSadded (VS, volatile solid. Neutral detergent fiber concentration was low (44.47% DM, dry matter, yet mineral concentration was high in comparison to grass types cut at a lower frequency. Concentrations of Cl, N, and S, which may lead to unfavorable emissions, fouling, and corrosion during combustion, were too high for an unproblematic combustion process. This was still the case even after applying a mineral-reducing pretreatment, which generates a fiber-rich press cake and a press fluid rich in easy soluble substances. Digestion of the press fluid led to methane yields of 340.10 lN·kg−1 VSadded and the press cake had a higher heating value of 19.61 MJ·kg−1 DM, which is close to that of coniferous wood. It can be concluded that biomass from sports fields could be a suitable co-substrate in bio-energy generation.

Cutting method and device underwater

International Nuclear Information System (INIS)

Takano, Genta; Kamei, Hiromasa; Beppu, Seiji

1998-01-01

A place of material to be cut is surrounded by an openable/closable box. The material to be cut is cut underwater, and materials generated in this case are removed from the cut portion by a pressurized water jet. The removed materials are sucked and recovered together with water in the box. Among the materials caused by the cutting underwater, solid materials not floating on water are caused to stay in the midway of a sucking and recovering channel. A large sucking force might be required for the entire region of the sucking and recovering channel when sucking and recovering large sized solid materials not floating on water, but even large sized materials can be recovered easily according to the present invention since they are recovered after being sucked and stayed in the midway of the sucking and recovering channel. (N.H.)

Regularities of dust formation during stone cutting for construction works

Directory of Open Access Journals (Sweden)

V.G. Lebedev

2016-09-01

Full Text Available When cutting stone, a large amount of dust release, which is a mixture of small, mostly sharp, mineral particles. Shallow dry dust with inhalation causes the pathological changes in organs that are a consequence of infiltration of acute and solids particles. Despite the importance of this problem, the questions of dust generation during the various working processes and its fractions distribution are practically not considered. This determines the time of dust standing in the air and its negative impact on a person. Aim: The aim of this research is to study the process of dusting during stones cutting and dust distribution on fractions regularities and quantification of dust formation process in order to improve the production equipment, staff individual and collective safety equipment. Materials and Methods: Many types of cutting can be divided into two types - a “dry” cutting and cutting with fluid. During “dry” cutting a dust represents a set of micro-chips which are cut off by the abrasive grains. The size of such chips very small: from a micrometer to a few micrometers fraction. Thus, the size of chips causes the possibility of creating dust slurry with low fall velocity, and which is located in the working space in large concentrations. Results: The following characteristic dependences were obtained as a result of research: dependence of the dust fall from the size of the dust particles, size of dust particles from minute feeding and grain range wheel, the specific amount of dust from the number of grit abrasive wheel and the temperature of the dust particles from the feeding at wheel turnover. It was shown that the distribution of chips (dust by size will request of a normal distribution low. Dimensions of chips during cut are in the range of 0.4...6 μm. Thus, dust slurry is formed with time of particles fall of several hours. This creates considerable minute dust concentration - within 0.28∙10^8...1.68∙10^8 units/m3.

Fiscal year 2013 energy department budget: Proposed investments in clean energy research

Science.gov (United States)

Balcerak, Ernie

2012-03-01

Energy and environmental research programs generally fared well in President Barack Obama's proposed budget for the Department of Energy (DOE) for fiscal year (FY) 2013. In his State of the Union address, Obama called for the United States to pursue an "all of the above" energy strategy that includes fossil fuels, as well as a variety of renewable sources of energy. The DOE budget request supports that strategy, Energy Secretary Steven Chu said in a 13 February press briefing announcing the budget proposal. The proposed budget gives DOE 27.2 billion overall, a 3.2% increase from the FY 2012 enacted budget (see Table 1). This budget "reflects some tough choices," Chu said. The proposed budget would cut 4 billion in subsidies for oil and gas companies; many Republican members of Congress have already indicated that they oppose such cuts, suggesting that congressional approval of this budget may run into stumbling blocks. The budget would also cut funding for research and development projects that are already attracting private-sector investment or that are not working, and would reduce some of the department's operational costs.

Cutting zone area and chip morphology in high-speed cutting of titanium alloy Ti-6Al-4V

International Nuclear Information System (INIS)

Ke, Qing Chan; Xu, Daochun; Xiong, Dan Ping

2017-01-01

The titanium alloy Ti-6Al-4V has superior properties but poor machinability, yet is widely used in aerospace and biomedical industries. Chip formation and cutting zone area are important factors that have received limited attention. Thus, we propose a high-speed orthogonal cutting model for serrated chip formation. The high speed orthogonal cutting of Ti-6Al-4V was studied with a cutting speed of 10-160 m/min and a feed of 0.07-0.11 mm/r. Using theoretical models and experimental results, parameters such as chip shape, serration level, slip angle, and shear slip distance were investigated. Cutting zone boundaries (tool-chip contact length, length of shear plane, and critical slip plane) and cutting zone area were obtained. The results showed that discontinuous, long-curling, and continuous chips were formed at low, medium, and high speeds, respectively. Serration level, shear slip distance, and slip angle rose with increasing cutting speed. The length of shear plane, tool-chip contact, and critical slip plane varied subtly with increased cutting speed, and rose noticeably with increased feed. Cutting zone area grew weakly with increased cutting speed, levelling off at high cutting speed; however, it rose noticeably with increased feed. This study furthers our understanding of the shear slip phenomenon and the mechanism of serrated chip formation

Cutting zone area and chip morphology in high-speed cutting of titanium alloy Ti-6Al-4V

Energy Technology Data Exchange (ETDEWEB)

Ke, Qing Chan; Xu, Daochun; Xiong, Dan Ping [School of Technology, Beijing Forestry University, Beijing (China)

2017-01-15

The titanium alloy Ti-6Al-4V has superior properties but poor machinability, yet is widely used in aerospace and biomedical industries. Chip formation and cutting zone area are important factors that have received limited attention. Thus, we propose a high-speed orthogonal cutting model for serrated chip formation. The high speed orthogonal cutting of Ti-6Al-4V was studied with a cutting speed of 10-160 m/min and a feed of 0.07-0.11 mm/r. Using theoretical models and experimental results, parameters such as chip shape, serration level, slip angle, and shear slip distance were investigated. Cutting zone boundaries (tool-chip contact length, length of shear plane, and critical slip plane) and cutting zone area were obtained. The results showed that discontinuous, long-curling, and continuous chips were formed at low, medium, and high speeds, respectively. Serration level, shear slip distance, and slip angle rose with increasing cutting speed. The length of shear plane, tool-chip contact, and critical slip plane varied subtly with increased cutting speed, and rose noticeably with increased feed. Cutting zone area grew weakly with increased cutting speed, levelling off at high cutting speed; however, it rose noticeably with increased feed. This study furthers our understanding of the shear slip phenomenon and the mechanism of serrated chip formation.

Effects of cutting and maturity on antioxidant activity of fresh-cut tomatoes

NARCIS (Netherlands)

Moreira Lana, M.; Tijskens, L.M.M.

2006-01-01

To investigate the changes in total antioxidant activity of fresh-cut tomato during storage, tomato fruits harvested at three different stages of maturity were cut into 7-mm thick slices and stored at 5 °C. Intact fruits were stored in the same conditions as a control. The antioxidant activity was

Respiration rate and ethylene production of fresh cut lettuce as affected by cutting grade

Directory of Open Access Journals (Sweden)

J. MARTÍNEZ

2008-12-01

Full Text Available For designing optimal polymeric films for modified atmosphere packaging of whole heads as well as for minimally fresh processed (fresh-cut Iceberg lettuce ‘Coolguard’, the effect of several cutting grades on respiration rate (RR and ethylene production at 5ºC was studied. According to common industrial practices cutting grades less than 0.5 cm, between 0.5 and 1 cm, and 2 cm length were selected. Results from four experiments were compared to those obtained for whole heads in which a homogenous range of 6 to 8 ml CO2 kg-1 h-1 in RR was found. Compared to whole heads, in fresh-cut lettuce the RR was 2-fold higher. The lowest cutting grade showed the highest respiration rate, and no significant differences in RR among lettuce pieces of intermediate and the highest grades were found. No ethylene production was detected in whole heads, while in minimally processed lettuce pieces only traces were found. For avoiding risks of anaerobic respiration and excessive CO2 levels within packages containing fresh-cut lettuce pieces lower than 0.5 cm length, films with relatively high O2 permeability like standard polypropylene or low-density polyethylene must be selected.;

Specificity of the mutualistic association between actinomycete bacteria and two sympatric species of Acromyrmex leaf-cutting ants

DEFF Research Database (Denmark)

Poulsen, M; Cafaro, M; Boomsma, J J

2005-01-01

Acromyrmex leaf-cutting ants maintain two highly specialized, vertically transmitted mutualistic ectosymbionts: basidiomycete fungi that are cultivated for food in underground gardens and actinomycete Pseudonocardia bacteria that are reared on the cuticle to produce antibiotics that suppress...

Cut-off scaling of high-harmonic generation driven by a femtosecond visible optical parametric amplifier

International Nuclear Information System (INIS)

Cirmi, Giovanni; Lai, Chien-Jen; Granados, Eduardo; Huang, Shu-Wei; Sell, Alexander; Hong, Kyung-Han; Moses, Jeffrey; Keathley, Phillip; Kärtner, Franz X

2012-01-01

We studied high-harmonic generation (HHG) in Ar, Ne and He gas jets using a broadly tunable, high-energy optical parametric amplifier (OPA) in the visible wavelength range. We optimized the noncollinear OPA to deliver tunable, femtosecond pulses with 200-500 µJ energy at the 1 kHz repetition rate with excellent spatiotemporal properties, suitable for HHG experiments. By tuning the central wavelength of the OPA while keeping other parameters (energy, duration and beam size) constant, we experimentally studied the scaling law of cut-off energy with the driver wavelength in helium. Our measurements show a λ 1.7+0.2 dependence of the HHG cut-off photon energy over the full visible range in agreement with previous experiments of near- and mid-IR wavelengths. By tuning the central wavelength of the driver source, the high-order harmonic spectra in the extreme ultraviolet cover the full range of photon energy between ∼25 and ∼100 eV. Due to the high coherence intrinsic in HHG, as well as the broad and continuous tunability in the extreme UV range, a high energy, high repetition rate version of this source might be an ideal seed for free electron lasers.

Laser cutting system

Science.gov (United States)

Dougherty, Thomas J

2015-03-03

A workpiece cutting apparatus includes a laser source, a first suction system, and a first finger configured to guide a workpiece as it moves past the laser source. The first finger includes a first end provided adjacent a point where a laser from the laser source cuts the workpiece, and the first end of the first finger includes an aperture in fluid communication with the first suction system.

Dijet rates with symmetric Et cuts

International Nuclear Information System (INIS)

Banfi, Andrea; Dasgupta, Mrinal

2004-01-01

We consider dijet production in the region where symmetric cuts on the transverse energy, E t , are applied to the jets. In this region next-to-leading order calculations are unreliable and an all-order resummation of soft gluon effects is needed, which we carry out. Although, for illustrative purposes, we choose dijets produced in deep inelastic scattering, our general ideas apply additionally to dijets produced in photoproduction or gamma-gamma processes and should be relevant also to the study of prompt di-photon E t spectra in association with a recoiling jet, in hadron-hadron processes. (author)

Trim cut machining and surface integrity analysis of Nimonic 80A alloy using wire cut EDM

Directory of Open Access Journals (Sweden)

Amitesh Goswami

2017-02-01

Full Text Available This present work deals with the features of trim cut wire EDM machining of Nimonic 80A in terms of machining parameters, to predict material removal rate (MRR, surface roughness (Ra, wire wear ratio (WWR and microstructure analysis. Trim cut is performed after rough cut to remove the rough layer deposited after machining due to melting and re-solidification of the eroded metal from workpiece as well as from wire electrode. Taguchi’s design of experiments methodology has been used for planning and designing the experiments. The relative significance of various factors has also been evaluated and analyzed using ANOVA. The results clearly indicate trim cut potential for high surface finish compared to rough cut machining.

Identification and characterization of a novel Cut family cDNA that encodes human copper transporter protein CutC

International Nuclear Information System (INIS)

Li Jixi; Ji Chaoneng; Chen Jinzhong; Yang Zhenxing; Wang Yijing; Fei, Xiangwei; Zheng Mei; Gu Xing; Wen Ge; Xie Yi; Mao Yumin

2005-01-01

Copper is an essential heavy metal trace element that plays important roles in cell physiology. The Cut family was associated with the copper homeostasis and involved in several important metabolisms, such as uptake, storage, delivery, and efflux of copper. In this study, a novel Cut family cDNA was isolated from the human fetal brain library, which encodes a 273 amino acid protein with a molecular mass of about 29.3 kDa and a calculated pI of 8.17. It was named hCutC (human copper transporter protein CutC). The ORF of hCutC gene was cloned into pQE30 vector and expressed in Escherichia coli M15. The secreted hCutC protein was purified to a homogenicity of 95% by using the Ni-NTA affinity chromatography. RT-PCR analysis showed that the hCutC gene expressed extensively in human tissues. Subcellular location analysis of hCutC-EGFP fusion protein revealed that hCutC was distributed to cytoplasm of COS-7 cells, and both cytoplasm and nucleus of AD293 cells. The results suggest that hCutC may be one shuttle protein and play important roles in intracellular copper trafficking

Analytic properties of finite-temperature self-energies

International Nuclear Information System (INIS)

Weldon, H. Arthur

2002-01-01

The analytic properties in the energy variable k 0 of finite-temperature self-energies are investigated. A typical branch cut results from n particles being emitted into the heat bath and n ' being absorbed from the heat bath. There are three main results: First, in addition to the branch points at which the cuts terminate, there are also branch points attached to the cuts along their length. Second, branch points at k 0 =±k are ubiquitous and for massive particles they are essential singularities. Third, in a perturbative expansion using free particle propagators or in a resummed expansion in which the propagator pole occurs at a real energy, the self-energy will have a branch point at the pole location

Laser Cutting of Different Materials

Directory of Open Access Journals (Sweden)

Kadir ÇAVDAR

2013-08-01

Full Text Available In this paper; in general potential developments and trends of a particular machining field by extensively evaluating present studies of laser beam machining have been discussed. As it is indicated below, technical literatures have been subsumed under five major headlines: Experimental studies, reviews, optimization researches of the cutting parameters, theoretical modelling studies of laser beam cutting and academic studies relating to laser cutting

Comparative study of 0° X-cut and Y + 36°-cut lithium niobate high-voltage sensing

Science.gov (United States)

Patel, N.; Branch, D. W.; Schamiloglu, E.; Cular, S.

2015-08-01

A comparison study between Y + 36° and 0° X-cut lithium niobate (LiNbO3) was performed to evaluate the influence of crystal cut on the acoustic propagation to realize a piezoelectric high-voltage sensor. The acoustic time-of-flight for each crystal cut was measured when applying direct current (DC), alternating current (AC), and pulsed voltages. Results show that the voltage-induced shift in the acoustic wave propagation time scaled quadratically with voltage for DC and AC voltages applied to X-cut crystals. For the Y + 36° crystal, the voltage-induced shift scales linearly with DC voltages and quadratically with AC voltages. When applying 5 μs voltage pulses to both crystals, the voltage-induced shift scaled linearly with voltage. For the Y + 36° cut, the voltage-induced shift from applying DC voltages ranged from 10 to 54 ps and 35 to 778 ps for AC voltages at 640 V over the frequency range of 100 Hz-100 kHz. Using the same conditions as the Y + 36° cut, the 0° X-cut crystal sensed a shift of 10-273 ps for DC voltages and 189-813 ps for AC voltage application. For 5 μs voltage pulses, the 0° X-cut crystal sensed a voltage induced shift of 0.250-2 ns and the Y + 36°-cut crystal sensed a time shift of 0.115-1.6 ns. This suggests a frequency sensitive response to voltage where the influence of the crystal cut was not a significant contributor under DC, AC, or pulsed voltage conditions. The measured DC data were compared to a 1-D impedance matrix model where the predicted incremental length changed as a function of voltage. When the voltage source error was eliminated through physical modeling from the uncertainty budget, the combined uncertainty of the sensor (within a 95% confidence interval) decreased to 0.0033% using a Y + 36°-cut crystal and 0.0032% using an X-cut crystal for all the voltage conditions used in this experiment.

Industrial Energy Audit Guidebook: Guidelines for Conducting an Energy Audit in Industrial Facilities

Energy Technology Data Exchange (ETDEWEB)

Hasanbeigi, Ali; Price, Lynn

2010-10-07

Various studies in different countries have shown that significant energy-efficiency improvement opportunities exist in the industrial sector, many of which are cost-effective. These energy-efficiency options include both cross-cutting as well as sector-specific measures. However, industrial plants are not always aware of energy-efficiency improvement potentials. Conducting an energy audit is one of the first steps in identifying these potentials. Even so, many plants do not have the capacity to conduct an effective energy audit. In some countries, government policies and programs aim to assist industry to improve competitiveness through increased energy efficiency. However, usually only limited technical and financial resources for improving energy efficiency are available, especially for small and medium-sized enterprises. Information on energy auditing and practices should, therefore, be prepared and disseminated to industrial plants. This guidebook provides guidelines for energy auditors regarding the key elements for preparing for an energy audit, conducting an inventory and measuring energy use, analyzing energy bills, benchmarking, analyzing energy use patterns, identifying energy-efficiency opportunities, conducting cost-benefit analysis, preparing energy audit reports, and undertaking post-audit activities. The purpose of this guidebook is to assist energy auditors and engineers in the plant to conduct a well-structured and effective energy audit.

Structure of putative CutA1 from Homo sapiens determined at 2.05 Å resolution

International Nuclear Information System (INIS)

Bagautdinov, Bagautdin; Matsuura, Yoshinori; Bagautdinova, Svetlana; Kunishima, Naoki; Yutani, Katsuhide

2008-01-01

The X-ray structure of human CutA1 was solved in space group P2 1 2 1 2 1 , with unit-cell parameters a = 68.69, b = 88.84, c = 125.33 Å and six molecules per asymmetric unit. The structure of human brain CutA1 (HsCutA1) has been determined using diffraction data to 2.05 Å resolution. HsCutA1 has been implicated in the anchoring of acetylcholinesterase in neuronal cell membranes, while its bacterial homologue Escherichia coli CutA1 is involved in copper tolerance. Additionally, the structure of HsCutA1 bears similarity to that of the signal transduction protein PII, which is involved in regulation of nitrogen metabolism. Although several crystal structures of CutA1 from various sources with different rotation angles and degrees of interaction between trimer interfaces have been reported, the specific functional role of CutA1 is still unclear. In this study, the X-ray structure of HsCutA1 was determined in space group P2 1 2 1 2 1 , with unit-cell parameters a = 68.69, b = 88.84, c = 125.33 Å and six molecules per asymmetric unit. HsCutA1 is a trimeric molecule with intertwined antiparallel β-strands; each subunit has a molecular weight of 14.6 kDa and contains 135 amino-acid residues. In order to obtain clues to the possible function of HsCutA1, its crystal structure was compared with those of other CutA1 and PII proteins

Optimization of Dimensional accuracy in plasma arc cutting process employing parametric modelling approach

Science.gov (United States)

Naik, Deepak kumar; Maity, K. P.

2018-03-01

Plasma arc cutting (PAC) is a high temperature thermal cutting process employed for the cutting of extensively high strength material which are difficult to cut through any other manufacturing process. This process involves high energized plasma arc to cut any conducting material with better dimensional accuracy in lesser time. This research work presents the effect of process parameter on to the dimensional accuracy of PAC process. The input process parameters were selected as arc voltage, standoff distance and cutting speed. A rectangular plate of 304L stainless steel of 10 mm thickness was taken for the experiment as a workpiece. Stainless steel is very extensively used material in manufacturing industries. Linear dimension were measured following Taguchi’s L16 orthogonal array design approach. Three levels were selected to conduct the experiment for each of the process parameter. In all experiments, clockwise cut direction was followed. The result obtained thorough measurement is further analyzed. Analysis of variance (ANOVA) and Analysis of means (ANOM) were performed to evaluate the effect of each process parameter. ANOVA analysis reveals the effect of input process parameter upon leaner dimension in X axis. The results of the work shows that the optimal setting of process parameter values for the leaner dimension on the X axis. The result of the investigations clearly show that the specific range of input process parameter achieved the improved machinability.

Optical Cutting Interruption Sensor for Fiber Lasers

Directory of Open Access Journals (Sweden)

Benedikt Adelmann

2015-09-01

Full Text Available We report on an optical sensor system attached to a 4 kW fiber laser cutting machine to detect cutting interruptions. The sensor records the thermal radiation from the process zone with a modified ring mirror and optical filter arrangement, which is placed between the cutting head and the collimator. The process radiation is sensed by a Si and InGaAs diode combination with the detected signals being digitalized with 20 kHz. To demonstrate the function of the sensor, signals arising during fusion cutting of 1 mm stainless steel and mild steel with and without cutting interruptions are evaluated and typical signatures derived. In the recorded signals the piercing process, the laser switch on and switch off point and waiting period are clearly resolved. To identify the cutting interruption, the signals of both Si and InGaAs diodes are high pass filtered and the signal fluctuation ranges being subsequently calculated. Introducing a correction factor, we identify that only in case of a cutting interruption the fluctuation range of the Si diode exceeds the InGaAs diode. This characteristic signature was successfully used to detect 80 cutting interruptions of 83 incomplete cuts (alpha error 3.6% and system recorded no cutting interruption from 110 faultless cuts (beta error of 0. This particularly high detection rate in combination with the easy integration of the sensor, highlight its potential for cutting interruption detection in industrial applications.

Results from Development of Model Specifications for Multifamily Energy Retrofits

Energy Technology Data Exchange (ETDEWEB)

Brozyna, K.

2012-08-01

Specifications, modeled after CSI MasterFormat, provide the trade contractors and builders with requirements and recommendations on specific building materials, components and industry practices that comply with the expectations and intent of the requirements within the various funding programs associated with a project. The goal is to create a greater level of consistency in execution of energy efficiency retrofits measures across the multiple regions a developer may work. IBACOS and Mercy Housing developed sample model specifications based on a common building construction type that Mercy Housing encounters.

Results From Development of Model Specifications for Multifamily Energy Retrofits

Energy Technology Data Exchange (ETDEWEB)

Brozyna, Kevin [IBACOS, Inc., Pittsburgh, PA (United States)

2012-08-01

Specifications, modeled after CSI MasterFormat, provide the trade contractors and builders with requirements and recommendations on specific building materials, components and industry practices that comply with the expectations and intent of the requirements within the various funding programs associated with a project. The goal is to create a greater level of consistency in execution of energy efficiency retrofits measures across the multiple regions a developer may work. IBACOS and Mercy Housing developed sample model specifications based on a common building construction type that Mercy Housing encounters.

Radioactive wear measurements of cutting tools made of metal in cutting aluminium alloys

International Nuclear Information System (INIS)

Frevert, E.

1977-01-01

The possibility of making quick checkings of the inhomogeneities of turning materials with radioactive wear measurements has been tested. After activation analysis of the long-lived radioisotopes of cutting tools made of hard metal a method for loss-free collection of the turnings has been developed. The detection limit of the abrasion is about 10 -8 g, the measuring times are 5-10 minutes. Special radiation protection measures are not necessary. An analysis of the abrasion showed that at the beginning of cutting the amount of cobalt is 6 times higher than in the normal composition of the used cutting tools. (author)

Practical use of visual medial temporal lobe atrophy cut-off scores in Alzheimer's disease: Validation in a large memory clinic population

International Nuclear Information System (INIS)

Claus, Jules J.; Holl, Dana C.; Roorda, Jelmen J.; Staekenborg, Salka S.; Schuur, Jacqueline; Koster, Pieter; Tielkes, Caroline E.M.; Scheltens, Philip

2017-01-01

To provide age-specific medial temporal lobe atrophy (MTA) cut-off scores for routine clinical practice as marker for Alzheimer's disease (AD). Patients with AD (n = 832, mean age 81.8 years) were compared with patients with subjective cognitive impairment (n = 333, mean age 71.8 years) in a large single-centre memory clinic. Mean of right and left MTA scores was determined with visual rating (Scheltens scale) using CT (0, no atrophy to 4, severe atrophy). Relationships between age and MTA scores were analysed with regression analysis. For various MTA cut-off scores, decade-specific sensitivity and specificity and area under the curve (AUC) values, computed with receiver operator characteristic curves, were determined. MTA strongly increased with age in both groups to a similar degree. Optimal MTA cut-off values for the age ranges <65, 65-74, 75-84 and ≥85 were: ≥1.0, ≥1.5, ≥ 2.0 and ≥2.0. Corresponding values of sensitivity and specificity were 83.3% and 86.4%; 73.7% and 84.6%; 73.7% and 76.2%; and 84.0% and 62.5%. From this large unique memory clinic cohort we suggest decade-specific MTA cut-off scores for clinical use. After age 85 years, however, the practical usefulness of the MTA cut-off is limited. (orig.)

Development of cutting device for irradiated fuel rod

International Nuclear Information System (INIS)

Lee, E. P.; Jun, Y. B.; Hong, K. P.; Min, D. K.; Lee, H. K.; Su, H. S.; Kim, K. S.; Kwon, H. M.; Joo, Y. S.; Yoo, K. S.; Joo, J. S.; Kim, E. K.

2004-01-01

Post Irradiation Examination(PIE) on irradiated fuel rods is essential for the evaluation of integrity and irradiation performance of fuel rods of commercial reactor fuel. For PIE, fuel rods should be cut very precisely. The cutting positions selected from NDT data are very important for further destructive examination and analysis. A fuel rod cutting device was developed witch can cut fuel rods longitudinal very precisely and can also cut the fuels into the same length rod cuts repeatedly. It is also easy to remove the fuel cutting powder after cutting works and it can extend the life time of cutting device and lower the contamination level of hot cell

Submerged cutting characteristics of abrasive suspension jet

International Nuclear Information System (INIS)

Shimizu, Seiji; Peng, Guoyi; Oguma, Yasuyuki; Nishikata, Hiroyuki

2015-01-01

An abrasive suspension jet (ASJ) formed by propelling abrasive suspension through a nozzle has a greater cutting capability than the conventional abrasive water jet. However the cutting capability of submerged ASJs decreases drastically with increasing the standoff distance and the pressure around the jet. A sheathed nozzle with ventilation for ASJs has been developed as a mean of extending the effective stand-off distance and improving the cutting capabilities under submerged condition. In the present investigation, cutting tests by ASJs in air and under submerged condition are conducted with specimens of aluminum alloy. Air coated ASJs are formed by using a sheathed nozzle with ventilation. The relative cutting depth is defined as the cutting depth under submerged condition divided by the cutting depth in air at the same standoff distance. The relative cutting depth is arranged effectually by the cavitation number based on the cavity pressure measured at the sheath. (author)

Addenbrooke's Cognitive Examination and Individual Domain Cut-Off Scores for Discriminating between Different Cognitive Subtypes of Parkinson's Disease.

Science.gov (United States)

Berankova, Dagmar; Janousova, Eva; Mrackova, Martina; Eliasova, Ilona; Kostalova, Milena; Skutilova, Svetlana; Rektorova, Irena

2015-01-01

Objective. The main aim of this study was to verify the sensitivity and specificity of Addenbrooke's Cognitive Examination-Revised (ACE-R) in discriminating between Parkinson's disease (PD) with normal cognition (PD-NC) and PD with mild cognitive impairment (PD-MCI) and between PD-MCI and PD with dementia (PD-D). We also evaluated how ACE-R correlates with neuropsychological cognitive tests in PD. Methods. We examined three age-matched groups of PD patients diagnosed according to the Movement Disorder Society Task Force criteria: PD-NC, PD-MCI, and PD-D. ROC analysis was used to establish specific cut-off scores of ACE-R and its domains. Correlation analyses were performed between ACE-R and its subtests with relevant neuropsychological tests. Results. Statistically significant differences between groups were demonstrated in global ACE-R scores and subscores, except in the language domain. ACE-R cut-off score of 88.5 points discriminated best between PD-MCI and PD-NC (sensitivity 0.68, specificity 0.91); ACE-R of 82.5 points distinguished best between PD-MCI and PD-D (sensitivity 0.70, specificity 0.73). The verbal fluency domain of ACE-R demonstrated the best discrimination between PD-NC and PD-MCI (cut-off score 11.5; sensitivity 0.70, specificity 0.73) while the orientation/attention subscore was best between PD-MCI and PD-D (cut-off score 15.5; sensitivity 0.90, specificity 0.97). ACE-R scores except for ACE-R language correlated with specific cognitive tests of interest.

Selection of parameters on laser cutting mild steel plates taking account of some manufacturing purposes

Science.gov (United States)

Asano, Hiroshi; Suzuki, Jippei; Kawakami, Hiroshi; Eguchi, Hiroshi

2003-11-01

There are large number of processing conditions which can be set for laser-cutting of plate materials, because importance of the objective for the cutting is different from product to product. This study aims to build a system which can set the processing conditions reasonably and efficiently. From plural processing objectives, roughness of cutting surface was taken up from among the required qualities, such as processing speed, circularity of a processed hole, height of dross on the rear side, roughness of cutting surfaces, accuracy of shapes and dimensions, and with of burning, to review the effects of the processing condition on the cutting surface including the drag line gap. In our experiments, a 1 kW CO2 gas laser machine was used to make laser-cutting samples and 389 combinations of samples were used. From the results of the experiments, the range of processing conditions which allow cutting is defined by the energy input per unit area HIA = 4.8 [J/mm2]. The values of roughness of the cutting surface on both front and rear sides of the plates can be reduced if the cutting speed is 1000 mm/min or higher, and they little change at small values if the heat input per unit area is within a range under 20 J/mm2. In a range of thin plate thickness, the drag gap on cutting surfaces can be evaluated by the heat input per unit area. In the case of thicker plate, the greater the duty is, the smaller the drag gap is, if the heat input per units area is kept unchanged. Cutting with small heat input is desirable for better roughness of cutting surface. Cutting with large heat input is required for better drag gap. In the scope of our study, a value 20 J/mm2 of heat input per unit area is recommended for laer-cutting of 0.8 - 4.5 mm thick mild steel plates.

Effects of Cutting Edge Microgeometry on Residual Stress in Orthogonal Cutting of Inconel 718 by FEM.

Science.gov (United States)

Shen, Qi; Liu, Zhanqiang; Hua, Yang; Zhao, Jinfu; Lv, Woyun; Mohsan, Aziz Ul Hassan