RESISTANCE TO THE ATTACK OF DRY-WOOD TERMITES (Cryptotermes brevis OF SIX WOOD SPECIES

Directory of Open Access Journals (Sweden)

Fabrício Gomes Gonçalves

2006-03-01

Full Text Available The dry wood termites are one of the largest causes of damages in wood used in Brazil. This work analyzed the attackof the Cryptotermes brevis in six commercials wood species in the north of the Rio de Janeiro and south of the Espírito Santo. The testobserved the number of holes, the percentage of died individuals and the damage of the pieces. When compared to the Pinus sp(reference, the species with less susceptibility to the attack were Cedrela fissilis, Cariocar brasiliense and Goupia glabra, that alsopresented the largest percentages of mortality of termites. The Schizolobium parahyba, Toona ciliata and the Tachigalia myrmecophyllawere the species with the highest level of damage.

Effect of Alternative Wood Species and First Thinning Wood on Oriented Strand Board Performance

Directory of Open Access Journals (Sweden)

Fabiane Salles Ferro

2018-01-01

Full Text Available This study aimed to evaluate the feasibility of using and influence of alternative wood species such as Cambará, Paricá, Pinus, and wood from first thinning operations on oriented strand board (OSB physical and mechanical properties. Besides that, an alternative resin, castor oil-based polyurethane, was used to bond the particles, due to the better environmental performance when compared to other resins commonly used worldwide in OSB production. Physical properties such as the moisture content, thickness swelling, and water absorption, both after 2 and 24 hours of water immersion, and mechanical properties such as the modulus of elasticity and resistance in static bending, in major and minor axes, and internal bonding were investigated. All tests were performed according to European code EN 300:2006. Results showed the influence of wood species on physical and mechanical properties. Panels made with higher density woods such as Cambará presented better physical performance, while those made with lower density woods such as Pinus presented better mechanical properties. Besides that, strand particle geometry was also influenced on all physical and mechanical properties investigated. Therefore, the feasibility of using alternative species and wood from first thinning and with castor oil-based polyurethane resin in OSB production was verified.

Response of Microtermes mycophagus (Isoptera: Termitidae to twenty one wood species

Directory of Open Access Journals (Sweden)

Naeem Iqbal

2015-08-01

Full Text Available The responses of termite species to bait depend upon the quality of the food used in the stations. Woods are the most common food sources for termites but different termite species behave differently to different wood species and types. The knowledge of the preference status of different wood species to a termite species helps in effective monitoring and baiting program. The current study was carried out to evaluate the preference of 21 wood species to the termite, Microtermes mycophagus in the field by no-choice and choice feeding tests. The results indicated silk cotton tree and sacred fig woods as the most preferred wood species with mean mass losses of 71.21 ± 5.09% and 68.38 ± 7.27% in no-choice test and 95.02 ± 1.65% and 91.69 ± 2.07% in choice tests, respectively. White cedar was the least preferred wood species with mean mass losses of 7.49 ± 1.64% and 13.92 ± 1.89% in no choice and choice feeding tests, respectively. Based on present studies, sapwood of silk cotton tree and sacred fig may be used in effective monitoring and baiting program against M. mycophagus.

INFLUENCE OF COCONUT SHELL ADDITION ON PHYSICO-MECHANICAL PROPERTIES OF WOOD PLASTIC COMPOSITES1

Directory of Open Access Journals (Sweden)

Éverton Hillig

2018-04-01

Full Text Available ABSTRACT In this study, composites with three types of thermoplastic matrix and cellulosic material in a proportion of 40% were produced. The three thermoplastic matrices were high density polyethylene (HDPE, polypropylene (PP and low density polyethylene (LDPE, and the cellulosic materials were pure wood flour (Pinus taeda L or a mixture of wood flour and coconut shell flour (Cocus nucifera L in equal ratios. The objective was to evaluate the influence of addition of coconut shell on the physico-mechanical properties (density, strength and rigidity and the distribution of the cellulosic material in the thermoplastic matrix of the manufactured composites. It was found that the composites had a satisfactory distribution of wood flour in thermoplastic matrices, but the addition of coconut shell promoted bubble formation in the resulting pieces and, thus, interfered with the material properties. The use of a coupling agent promoted interfacial adhesion (cellulose - thermoplastic matrix, which was better in high density polyethylene composites, followed by polypropylene and low density polyethylene. In general, the coconut shell addition caused a decrease of all properties compared to composites made with Loblolly Pine. In addition, the interactions between thermoplastic type and cellulosic matrix type have been statistically confirmed, which caused variations in the studied properties

The trait contribution to wood decomposition rates of 15 Neotropical tree species.

Science.gov (United States)

van Geffen, Koert G; Poorter, Lourens; Sass-Klaassen, Ute; van Logtestijn, Richard S P; Cornelissen, Johannes H C

2010-12-01

The decomposition of dead wood is a critical uncertainty in models of the global carbon cycle. Despite this, relatively few studies have focused on dead wood decomposition, with a strong bias to higher latitudes. Especially the effect of interspecific variation in species traits on differences in wood decomposition rates remains unknown. In order to fill these gaps, we applied a novel method to study long-term wood decomposition of 15 tree species in a Bolivian semi-evergreen tropical moist forest. We hypothesized that interspecific differences in species traits are important drivers of variation in wood decomposition rates. Wood decomposition rates (fractional mass loss) varied between 0.01 and 0.31 yr(-1). We measured 10 different chemical, anatomical, and morphological traits for all species. The species' average traits were useful predictors of wood decomposition rates, particularly the average diameter (dbh) of the tree species (R2 = 0.41). Lignin concentration further increased the proportion of explained inter-specific variation in wood decomposition (both negative relations, cumulative R2 = 0.55), although it did not significantly explain variation in wood decomposition rates if considered alone. When dbh values of the actual dead trees sampled for decomposition rate determination were used as a predictor variable, the final model (including dead tree dbh and lignin concentration) explained even more variation in wood decomposition rates (R2 = 0.71), underlining the importance of dbh in wood decomposition. Other traits, including wood density, wood anatomical traits, macronutrient concentrations, and the amount of phenolic extractives could not significantly explain the variation in wood decomposition rates. The surprising results of this multi-species study, in which for the first time a large set of traits is explicitly linked to wood decomposition rates, merits further testing in other forest ecosystems.

Soil-wood interactions

NARCIS (Netherlands)

Wal, van der Annemieke; klein Gunnewiek, Paulien; Boer, de Wietse

2017-01-01

Wood-inhabiting fungi may affect soil fungal communities directly underneath decaying wood via their exploratory hyphae. In addition, differences in wood leachates between decaying tree species may influence soil fungal communities. We determined the composition of fungi in 4-yr old decaying logs

Migration of vascular plant species to a recent wood adjoining ancient woodland

Directory of Open Access Journals (Sweden)

Zbigniew Dzwonko

2014-01-01

Full Text Available Woodland communities can be restored by natural succession in sites adjoining ancient woodlands which can act as seed sources for trees, shrubs and woodland herbs. The influence of dominant tree species and the distance from an adjacent ancient oak-hornbeam woodland upon the floristic composition of species in a recent pine wood planted on dry rendzina soil were studied. It was found that, in spite of a 52-year long succession, the border between woods was sharp and the composition of species in the recent wood were significantly different than in the adjacent ancient woodland. Canonical correspondence analysis (CCA showed that the distance to the ancient woodland had a significant influence on species distributions in the recent wood. The numbers of species from the Querco-Fagetea class, vegetatively reproducing species and myrmecochores decreased with this distance, whereas the numbers of anemochores increased. The migration rate of many woodland species, calculated on occurrence of the farthest individuals was very slow, varying from 0.0 m year-1 to 0.38 m year-1. The restoration of the field layer vegetation in the studied pine wood was much slower than in recent deciduous woods on rich and moist soils where the migration rate of some species exceeded 1.50 m year-1. Recent woods adjacent to ancient woodlands can be more effectively colonised by woodland species only when they are dominated by broad-leaved trees with quickly decomposing litter, and the spatial continuity of these woods persists for a long period.

EFFECTS OF BURN RATE, WOOD SPECIES, MOISTURE CONTENT AND WEIGHT OF WOOD LOADED ON WOODSTOVE EMISSIONS

Science.gov (United States)

The report gives results of tests of four woodstove operating parameters (burn rate, wood moisture, wood load, and wood species) at two levels each using a half factorial experimental test design to determine statistically significant effects on the emission components CO, CO2, p...

Prioritization of Wood Species Utilized for Furniture Making in ...

African Journals Online (AJOL)

The preference for wood species varied among the three cities and among the three scales of furniture factories. However, Mansonia altissima was most preferred in the three cities with rates of 99.0%, 97.4% and 97.7% in Lagos, Ibadan and Benin respectively. 39 wood species were compiled from the lists of the three cities ...

Colorimetric characterization of three wood species from the amazon forest

Directory of Open Access Journals (Sweden)

Sâmia Valéria dos Santos Barros

2014-09-01

Full Text Available The aim of this study was to analyze wood color variability in the (radial, tangential and transversal anatomic sections of Breu-vermelho, Tauari-vermelho and Pequiarana species through quantitative colorimetry using CIELAB color system. Such species come from a forest sustainable area of Thousand Precious Woods Company, located in Itacoatiara in the Amazon region of Brazil. Five wood samples from each species were selected so as to determine the following colorimetric parameters: L*, a*, b*, C e h*. In addition, 225 measurements were carried out with Konica Minolta CM-5 spectrophotometer connected to the computer. Results pointed out to statistical differences in the colorimetric parameters and also a low saturation in a* in the analyzed species. According to the cluster gathering, Breu-vermelho wood presents olive and/or grayish pink color, Tauari-vermelho is pinkish-gray and Pequiarana is grayish-pink and/or pinkish-gray. Such species presented differences in color among the three anatomic sections cited above and were also influenced by the yellow color defined in b* parameter. To summarize, colorimetric analysis to establish wood color is a simple procedure which may be used from the sawing of the logs until their final exploitation enabling value aggregation to the final product.

DNA barcoding of vouchered xylarium wood specimens of nine endangered Dalbergia species.

Science.gov (United States)

Yu, Min; Jiao, Lichao; Guo, Juan; Wiedenhoeft, Alex C; He, Tuo; Jiang, Xiaomei; Yin, Yafang

2017-12-01

ITS2+ trnH - psbA was the best combination of DNA barcode to resolve the Dalbergia wood species studied. We demonstrate the feasibility of building a DNA barcode reference database using xylarium wood specimens. The increase in illegal logging and timber trade of CITES-listed tropical species necessitates the development of unambiguous identification methods at the species level. For these methods to be fully functional and deployable for law enforcement, they must work using wood or wood products. DNA barcoding of wood has been promoted as a promising tool for species identification; however, the main barrier to extensive application of DNA barcoding to wood is the lack of a comprehensive and reliable DNA reference library of barcodes from wood. In this study, xylarium wood specimens of nine Dalbergia species were selected from the Wood Collection of the Chinese Academy of Forestry and DNA was then extracted from them for further PCR amplification of eight potential DNA barcode sequences (ITS2, matK, trnL, trnH-psbA, trnV-trnM1, trnV-trnM2, trnC-petN, and trnS-trnG). The barcodes were tested singly and in combination for species-level discrimination ability by tree-based [neighbor-joining (NJ)] and distance-based (TaxonDNA) methods. We found that the discrimination ability of DNA barcodes in combination was higher than any single DNA marker among the Dalbergia species studied, with the best two-marker combination of ITS2+trnH-psbA analyzed with NJ trees performing the best (100% accuracy). These barcodes are relatively short regions (wood as the source material, a necessary factor to apply DNA barcoding to timber trade. The present results demonstrate the feasibility of using vouchered xylarium specimens to build DNA barcoding reference databases.

Wood Chemical Composition in Species of Cactaceae: The Relationship between Lignification and Stem Morphology

Science.gov (United States)

Canché-Escamilla, Gonzalo; Soto-Hernández, Marcos

2015-01-01

In Cactaceae, wood anatomy is related to stem morphology in terms of the conferred support. In species of cacti with dimorphic wood, a unique process occurs in which the cambium stops producing wide-band tracheids (WBTs) and produces fibers; this is associated with the aging of individuals and increases in size. Stem support and lignification have only been studied in fibrous tree-like species, and studies in species with WBTs or dimorphic wood are lacking. In this study, we approach this process with a chemical focus, emphasizing the role of wood lignification. We hypothesized that the degree of wood lignification in Cactaceae increases with height of the species and that its chemical composition varies with wood anatomy. To test this, we studied the chemical composition (cellulose, hemicellulose, and lignin content) in 13 species (2 WBTs wood, 3 dimorphic, and 8 fibrous) with contrasting growth forms. We also analyzed lignification in dimorphic and fibrous species to determine the chemical features of WBTs and fibers and their relationship with stem support. The lignin contents were characterized by Fourier transform infrared spectroscopy and high performance liquid chromatography. We found that 11 species have a higher percentage (>35%) of lignin in their wood than other angiosperms or gymnosperms. The lignin chemical composition in fibrous species is similar to that of other dicots, but it is markedly heterogeneous in non-fibrous species where WBTs are abundant. The lignification in WBTs is associated with the resistance to high water pressure within cells rather than the contribution to mechanical support. Dimorphic wood species are usually richer in syringyl lignin, and tree-like species with lignified rays have more guaiacyl lignin. The results suggest that wood anatomy and lignin distribution play an important role in the chemical composition of wood, and further research is needed at the cellular level. PMID:25880223

Wood chemical composition in species of Cactaceae: the relationship between lignification and stem morphology.

Directory of Open Access Journals (Sweden)

Jorge Reyes-Rivera

Full Text Available In Cactaceae, wood anatomy is related to stem morphology in terms of the conferred support. In species of cacti with dimorphic wood, a unique process occurs in which the cambium stops producing wide-band tracheids (WBTs and produces fibers; this is associated with the aging of individuals and increases in size. Stem support and lignification have only been studied in fibrous tree-like species, and studies in species with WBTs or dimorphic wood are lacking. In this study, we approach this process with a chemical focus, emphasizing the role of wood lignification. We hypothesized that the degree of wood lignification in Cactaceae increases with height of the species and that its chemical composition varies with wood anatomy. To test this, we studied the chemical composition (cellulose, hemicellulose, and lignin content in 13 species (2 WBTs wood, 3 dimorphic, and 8 fibrous with contrasting growth forms. We also analyzed lignification in dimorphic and fibrous species to determine the chemical features of WBTs and fibers and their relationship with stem support. The lignin contents were characterized by Fourier transform infrared spectroscopy and high performance liquid chromatography. We found that 11 species have a higher percentage (>35% of lignin in their wood than other angiosperms or gymnosperms. The lignin chemical composition in fibrous species is similar to that of other dicots, but it is markedly heterogeneous in non-fibrous species where WBTs are abundant. The lignification in WBTs is associated with the resistance to high water pressure within cells rather than the contribution to mechanical support. Dimorphic wood species are usually richer in syringyl lignin, and tree-like species with lignified rays have more guaiacyl lignin. The results suggest that wood anatomy and lignin distribution play an important role in the chemical composition of wood, and further research is needed at the cellular level.

Wood chemical composition in species of Cactaceae: the relationship between lignification and stem morphology.

Science.gov (United States)

Reyes-Rivera, Jorge; Canché-Escamilla, Gonzalo; Soto-Hernández, Marcos; Terrazas, Teresa

2015-01-01

In Cactaceae, wood anatomy is related to stem morphology in terms of the conferred support. In species of cacti with dimorphic wood, a unique process occurs in which the cambium stops producing wide-band tracheids (WBTs) and produces fibers; this is associated with the aging of individuals and increases in size. Stem support and lignification have only been studied in fibrous tree-like species, and studies in species with WBTs or dimorphic wood are lacking. In this study, we approach this process with a chemical focus, emphasizing the role of wood lignification. We hypothesized that the degree of wood lignification in Cactaceae increases with height of the species and that its chemical composition varies with wood anatomy. To test this, we studied the chemical composition (cellulose, hemicellulose, and lignin content) in 13 species (2 WBTs wood, 3 dimorphic, and 8 fibrous) with contrasting growth forms. We also analyzed lignification in dimorphic and fibrous species to determine the chemical features of WBTs and fibers and their relationship with stem support. The lignin contents were characterized by Fourier transform infrared spectroscopy and high performance liquid chromatography. We found that 11 species have a higher percentage (>35%) of lignin in their wood than other angiosperms or gymnosperms. The lignin chemical composition in fibrous species is similar to that of other dicots, but it is markedly heterogeneous in non-fibrous species where WBTs are abundant. The lignification in WBTs is associated with the resistance to high water pressure within cells rather than the contribution to mechanical support. Dimorphic wood species are usually richer in syringyl lignin, and tree-like species with lignified rays have more guaiacyl lignin. The results suggest that wood anatomy and lignin distribution play an important role in the chemical composition of wood, and further research is needed at the cellular level.

Wood chemistry symposium: from muka to lignin

Energy Technology Data Exchange (ETDEWEB)

MacLeod, M.

1979-01-01

The Canadian Wood Chemistry Symposium held during September, 1979, is reviewed. The chemical and physical explanations of delignification were debated. Problems of mechanical pulping include insufficient brightness, yellowing, and low strength relative to energy consumption. A session on chemicals, energy, and food from wood began with criteria for a viable project, which included adequate return on investment, modest capital investment requirements, identified pre-existing markets, and favorable thermodynamic balances. The pulp and paper industry should improve its methods of using bark and wood waste in direct combustion (by pre-drying wastes and improving furnace efficiency) rather than supporting oil-from-wood projects, since using a waste for fuel will free fossil fuels for uses in synthetic fibers and thermoplastics. In the area of food, there are modest successes with cellulose fiber additives to bread and snack food and single cell protein (which, though made from wastes, cannot compete with soy protein). However, making monomeric sugars from wood polysaccharides is not an efficient process, and muka, animal feed supplement from foliage, is successful only in Russia. In Canada it cannot compete with agricultural products. Alpha cellulose is a major wood chemical product. Promising uses include cellulose derived thermoplastics and lignosulphonates for secondary oil recovery. Instead of breaking wood polysaccharides and lignin into monomers and then repolymerizing them, it is possible to use the pre-built polymers; such an approach is illustrated by use of lignin in polyurethane foams, adhesives, and coatings.

Branch Wood Decomposition of Tree Species in a Deciduous Temperate Forest in Korea

Directory of Open Access Journals (Sweden)

Sangsub Cha

2017-05-01

Full Text Available Woody debris, which is supplied by branch litter, is an important component of forest ecosystems as it contains large quantities of organic matter and nutrients. We evaluated changes in branch wood dry weight and nutrient content of six common species (Fraxinus rhynchophylla, Pinus densiflora, Prunus sargentii, Quercus mongolica, Acer pseudosieboldianum, and Symplocos chinensis for. pilosa in a deciduous temperate forest in Korea for 40 months. Branch wood disk samples 1.4–1.6 cm thick were cut, and mass loss was measured over time using the litterbag method. No significant differences in mass loss were recorded among the six tree species. Further, mass loss was negatively correlated with initial lignin concentration and positively correlated with both initial cellulose concentration and wood density for each species. Species with high wood cellulose content had high wood density while the lignin content in wood was relatively low. Accordingly, cellulose contributed to wood density, creating a relatively lower lignin content, and the decreased lignin concentration increased the wood decomposition rate.

The suitability of selected wood species in the production of turned ...

African Journals Online (AJOL)

The study investigated the suitability of selected wood species in the production of turned glue-laminated products. Five different wood species of high quality grades which were sourced from Bodija market Ibadan, south western Nigeria were thoroughly examined where the moisture content, density and shrinkage ...

THERMAL DEGRADATION AND MORPHOLOGICAL ASPECTS OF FOUR WOOD SPECIES USED IN LUMBER INDUSTRY

Directory of Open Access Journals (Sweden)

Matheus Poletto

Full Text Available ABSTRACT The aim of this work was characterize four wood waste samples from lumber industry in order to obtain previous information about structure and properties of wood before use it as a biofuel or as reinforcement in composite formulations. The influence of wood components on the thermal degradation stability of different wood species has been investigated using thermogravimetry, differential scanning calorimetry and scanning electron microscopy. Four wood species, Eucalyptus grandis (EUG, Pinus elliottii (PIE, Dipteryx odorata (DIP and Mezilaurus itauba (ITA, were used in this study. The results showed that higher extractives contents may form a thin film on the wood fiber surface which can accelerate the degradation process and reduce the wood thermal stability

GC-MS Characterizations of Termiticidal Heartwood Extractives from Wood Species Utilized in Pakistan

Science.gov (United States)

Mark Mankowski; Blossie Boyd; Barbar Hassan; Grant T. Kirker

2016-01-01

Wood species that exhibit innate tolerance to wood destroying organisms such as termites are considered to be naturally durable. This durability can, in part, be due to the complex chemical compounds in the heartwood of naturally durable wood species. We examined the effects of varying concentrations of heartwood extractives on the subterranean termite, ...

Wood density and anatomy of three Eucalyptus species: implications for hydraulic conductivity

International Nuclear Information System (INIS)

Barotto, A.J.; Monteoliva, S.; Gyenge, J.; Martínez-Meier, A.; Moreno, K.; Tesón, N.; Fernández, M.E.

2017-01-01

Aim of the study: To characterize wood anatomical traits of three Eucalyptus species that differ in wood density and ecological requirements, and to examine the relationships between some anatomical features, wood density, and theoretical xylem hydraulic conductivity (Ks). Area of study: We analyzed 86 trees from three sites of Argentina (Entre Ríos and Buenos Aires Provinces). Methods: The sampled trees were Eucalyptus globulus, E. grandis and E. viminalis ranging from 11 to 15 years old. One stem disc was cut from each tree to determine wood density and identify quantitative anatomical features of vessels and fibers. Vessel composition (S, size - to-number ratio, a measure of vessel size distribution) and lumen fraction (F, the total sapwood area available for water transport) were estimated. Results: E. grandis, the species with the highest growth rates, presented the highest theoretical Ks. This was associated with anatomical features such as a high density of wide vessels resulting in high F. On the other hand, E. viminalis, the species with the lowest growth rates and highest resistance to environmental stress, showed lower Ks as a result of a low density of wide vessels. These two species differed not only greatly in wood density but also in fiber characteristics. In the case of E. globulus, vessels were relatively narrow, which resulted in the lowest theoretical Ks, fibers were small, and wood density intermediate. Research highlights: F had greater influence on Ks than S. The anatomical characteristics and wood density could only partly explain the differential growth or resistance to stress of the studied species.

Wood density and anatomy of three Eucalyptus species: implications for hydraulic conductivity

Directory of Open Access Journals (Sweden)

Antonio J. Barotto

2017-05-01

Full Text Available Aim of the study: To characterize wood anatomical traits of three Eucalyptus species that differ in wood density and ecological requirements, and to examine the relationships between some anatomical features, wood density, and theoretical xylem hydraulic conductivity (Ks. Area of study: We analyzed 86 trees from three sites of Argentina (Entre Ríos and Buenos Aires Provinces. Methods: The sampled trees were Eucalyptus globulus, E. grandis and E. viminalis ranging from 11 to 15 years old. One stem disc was cut from each tree to determine wood density and identify quantitative anatomical features of vessels and fibers. Vessel composition (S, size - to-number ratio, a measure of vessel size distribution and lumen fraction (F, the total sapwood area available for water transport were estimated. Results: E. grandis, the species with the highest growth rates, presented the highest theoretical Ks. This was associated with anatomical features such as a high density of wide vessels resulting in high F. On the other hand, E. viminalis, the species with the lowest growth rates and highest resistance to environmental stress, showed lower Ks as a result of a low density of wide vessels. These two species differed not only greatly in wood density but also in fiber characteristics. In the case of E. globulus, vessels were relatively narrow, which resulted in the lowest theoretical Ks, fibers were small, and wood density intermediate. Research highlights: F had greater influence on Ks than S. The anatomical characteristics and wood density could only partly explain the differential growth or resistance to stress of the studied species.

Wood density and anatomy of three Eucalyptus species: implications for hydraulic conductivity

Energy Technology Data Exchange (ETDEWEB)

Barotto, A.J.; Monteoliva, S.; Gyenge, J.; Martínez-Meier, A.; Moreno, K.; Tesón, N.; Fernández, M.E.

2017-11-01

Aim of the study: To characterize wood anatomical traits of three Eucalyptus species that differ in wood density and ecological requirements, and to examine the relationships between some anatomical features, wood density, and theoretical xylem hydraulic conductivity (Ks). Area of study: We analyzed 86 trees from three sites of Argentina (Entre Ríos and Buenos Aires Provinces). Methods: The sampled trees were Eucalyptus globulus, E. grandis and E. viminalis ranging from 11 to 15 years old. One stem disc was cut from each tree to determine wood density and identify quantitative anatomical features of vessels and fibers. Vessel composition (S, size - to-number ratio, a measure of vessel size distribution) and lumen fraction (F, the total sapwood area available for water transport) were estimated. Results: E. grandis, the species with the highest growth rates, presented the highest theoretical Ks. This was associated with anatomical features such as a high density of wide vessels resulting in high F. On the other hand, E. viminalis, the species with the lowest growth rates and highest resistance to environmental stress, showed lower Ks as a result of a low density of wide vessels. These two species differed not only greatly in wood density but also in fiber characteristics. In the case of E. globulus, vessels were relatively narrow, which resulted in the lowest theoretical Ks, fibers were small, and wood density intermediate. Research highlights: F had greater influence on Ks than S. The anatomical characteristics and wood density could only partly explain the differential growth or resistance to stress of the studied species.

A reassessment of carbon content in wood: variation within and between 41 North American species

International Nuclear Information System (INIS)

Lamlom, S.H.; Savidge, R.A.

2003-01-01

At present, 50% (w/w) carbon is widely promulgated as a generic value for wood; however, the literature yields few data and indicates that very little research has actually been done. C contents in heartwood of forty-one softwood and hardwood species were determined. C in kiln-dried hardwood species ranged from 46.2% to 49.97% (w/w), in conifers from 47.21% to 55.2%. The higher C in conifers agrees with their higher lignin content (∼30%, versus ∼20% for hardwoods). Wood-meal samples drilled from discrete early wood and late wood zones of seven of the forty-one species were also investigated. C contents of early woods were invariably higher than those in corresponding late woods, again in agreement with early wood having higher lignin content. Further investigation was made into freshly harvested wood of some species to determine how much volatile C is present, comparing oven-dried wood meal with wood meal dried at ambient temperature over a desiccant. C contents of oven-dried woods were significantly lower, indicating that all past data on C content in oven-dried or kiln-dried woods may be inaccurate in relation to the true C content of forests. We conclude that C content varies substantially among species as well as within individual trees. Clearly, a 50% generic value is an oversimplification of limited application in relation to global warming and the concept of 'carbon credits'. (author)

How does species name affect consumer choice? An analysis and implications for cabinet door marketers.

Science.gov (United States)

Joseph A. Roos; Geof Donovan; David. Nicholls

2005-01-01

Consumers choose products based on various tangible and intangible attributes. Previous research has shown that there is a difference between appearance-based and word-based evaluations of wood species. However, little research has been done on how this difference affects consumer choice. This study examined how the presence or absence of a species name affects a...

Thermal analysis of wood of the main tree species of Central Siberia

Directory of Open Access Journals (Sweden)

S. R. Loskutov

2015-12-01

Full Text Available Thermal decomposition of wood from coniferous and deciduous species of Siberia has been studied using thermogravimetry (TG and differential scanning calorimetry (DSC. The tree species were larch Larix sibirica Ledeb., Scots pine Pinus sylvestris L., spruce Picea obovata Ledeb., fir Abies sibirica Ledeb., Siberian pine Pinus sibirica Du Tour., birch Betula pendula Roth., and aspen Populus tremula L. Thermal analysis of wood samples was carried out under oxidative (air and inert (argon atmospheres from 25 to 700 °С at heating rates 10, 20, 40 °С • min–1 (TG/DTG and from 25 to 590 °С at heating rates 10, 40 °С • min–1 (DSC. The stages of thermal decomposition, the temperature intervals, the mass loss, the mass loss rate, the temperature of DTG/DSC peaks, and heating effects were determined for each tree species. The kinetic thermal degradation parameters of wood were obtained by the Broido and Ozawa–Flynn–Wall models. The wood of coniferous and deciduous species of Siberia was characterized on the base of analysis of activation energy values at various stages of thermal decomposition and the relations of activation energy on conversion level of wood substance of different tree species, and also the comparison of mass loss at the same stages of thermal destruction, heating effects, residual mass and other parameters of TG/DTG, DSC. In our opinion, the results of this work present interest for researchers and specialists in the field of forest pyrology, wood science, dendrochemistry.

Consequences of bioenergy wood extraction for landscape-level availability of habitat for dead wood-dependent organisms.

Science.gov (United States)

Hiron, Matthew; Jonsell, Mats; Kubart, Ariana; Thor, Göran; Schroeder, Martin; Dahlberg, Anders; Johansson, Victor; Ranius, Thomas

2017-08-01

Stumps and slash resulting from forest clearcutting is used as a source of low-net-carbon energy, but there are concerns about the consequences of biofuel extraction on biodiversity. Logging residues constitute potentially important habitats, since a large part of forest biodiversity is dependent on dead wood. Here we used snapshot field data from a managed forest landscape (25 000 ha) to predict landscape scale population changes of dead wood dependent organisms after extraction of stumps and slash after clearcutting. We did this by estimating habitat availability for all observed dead wood-dependent beetles, macrofungi, and lichens (380 species) in the whole landscape. We found that 53% of species occurred in slash or stumps. For most species, population declines after moderate extraction (≤30%) were small (dead wood types. However, some species were only recorded in slash and stumps. Red listed species were affected by slash and stump extraction (12 species), but less often than other species. Beetles and fungi were more affected by stump extraction, while lichens were more affected by slash extraction. For beetles and lichens, extraction of a combination of spruce, pine and birch resulted in larger negative effects than if only extracting spruce, while for fungi tree species had little effect. We conclude that extensive extraction decreases the amount of habitat to such extent that it may have negative consequences on species persistence at the landscape level. The negative consequences can be limited by extracting only slash, or only logging residues from spruce stands. Copyright © 2017 Elsevier Ltd. All rights reserved.

Final Report: Development of Renewable Microbial Polyesters for Cost Effective and Energy- Efficient Wood-Plastic Composites

Energy Technology Data Exchange (ETDEWEB)

Thompson, David N.; Emerick, Robert W.; England, Alfred B.; Flanders, James P.; Loge, Frank J.; Wiedeman, Katherine A.; Wolcott, Michael P.

2010-03-31

In this project, we proposed to produce wood fiber reinforced thermoplastic composites (WFRTCs) using microbial thermoplastic polyesters in place of petroleum-derived plastic. WFRTCs are a rapidly growing product area, averaging a 38% growth rate since 1997. Their production is dependent on substantial quantities of petroleum based thermoplastics, increasing their overall energy costs by over 230% when compared to traditional Engineered Wood Products (EWP). Utilizing bio-based thermoplastics for these materials can reduce our dependence on foreign petroleum. We have demonstrated that biopolymers (polyhydroxyalkanoates, PHA) can be successfully produced from wood pulping waste streams and that viable wood fiber reinforced thermoplastic composite products can be produced from these materials. The results show that microbial polyester (PHB in this study) can be extruded together with wastewater-derived cell mass and wood flour into deck products having performance properties comparable to existing commercial HDPE/WF composite products. This study has thus proven the underlying concept that the microbial polyesters produced from waste effluents can be used to make cost-effective and energy-efficient wood-plastic composites. The cost of purified microbial polyesters is about 5-20 times that of HDPE depending on the cost of crude oil, due to high purification (40%), carbon substrate (40%) and sterilized fermentation (20%) costs for the PHB. Hence, the ability to produce competitive and functional composites with unpurified PHA-biomass mixtures from waste carbon sources in unsterile systems—without cell debris removal—is a significant step forward in producing competitive value-added structural composites from forest products residuals using a biorefinery approach. As demonstrated in the energy and waste analysis for the project, significant energy savings and waste reductions can also be realized using this approach. We recommend that the next step for development of

Effects of species information and furniture price on consumer preferences for selected woods

Science.gov (United States)

Matthew Bumgardner; David Nicholls; Geoffrey Donovan

2007-01-01

Changing consumer tastes and species availability are influencing the design and manufacture of hardwood products. In addition, the globalization of wood product markets is exposing U.S. consumers to new species. This research evaluates consumer preferences for six domestic wood species--three from the eastern United States and three from the western United States. The...

The trait contribution to wood decomposition rates of 15 neotropical tree species

NARCIS (Netherlands)

Geffen, van K.G.; Poorter, L.; Sass-Klaassen, U.; Logtestijn, R.S.P.; Cornelissen, J.H.C.

2010-01-01

The decomposition of dead wood is a critical uncertainty in models of the global carbon cycle. Despite this, relatively few studies have focused on dead wood decomposition, with a strong bias to higher latitudes. Especially the effect of inter-specific variation in species traits on differences wood

Radiation processing of wood-plastic composites

International Nuclear Information System (INIS)

Czvikovszky, T.

1992-01-01

There are three main types of radiation-processed composite material derived from plastics and fibrous natural polymers. The first are the monomer-impregnated, radiation-treated wood-plastic composites (WPC). They became a commercial success in the early 1970s. More recently, work has focused on improving the WPCs by creating in them interpenetrating network (IPN) systems by the use of appropriate multifunctional oligomers and monomers. The main kinetic features of radiation-initiated chain polymerization remain applicable even in impregnated wood. The second type are the plastics filled or reinforced with dispersed wood fiber or other cellulosics (WFRP). In their case, radiation processing offers a new opportunity to apply radiation-reactive adhesion promoters between wood or cellulosic fibers and the thermoplastic matrices. The third type are the laminar composites made by electron beam coating of wood-based agglomerate sheets and boards. This chapter reviews the industrial applications and the radiation processing of the three types of the wood-plastic composites and indicates future trends. (orig.)

ANATOMICAL PROPERTIES AND FIBER QUALITY OF FIVE POTENTIAL COMMERCIAL WOOD SPECIES FROM CIANJUR, WEST JAVA

Directory of Open Access Journals (Sweden)

Ratih Damayanti

2010-06-01

Full Text Available A detailed description of wood anatomy is essential for assessing the use of a wood species for processing , and also beneficial for the identification of wood samples. Computerized keys are available that allow the identification of wood samples until the genus level; however, it is not easy to use these keys to identif y unknown species. Therefore, a database of anatomical characteristics and the computerized keys need to be completed up to species level. As the relevance, this study has examined the wood anatomical properties of the five corresponding tree species originated from Cianjur, West Java, which are commercially potential for their exploitation, i.e Castanopsis acuminatissima ADC. (Fagaceae; Castanopsistungurrut ADC. (Fagaceae; Cinnamomum inners Reinw. ex Blume (Lauraceae; Ficus nervosa Heyne (Moraceae and Horsfieldia glabra Warb. (Myristicaceae. Expectedly the results would be beneficial for wood identification purposes and evaluation for other possible uses. Obser vations on anatomical structures covered macroscopic and microscopic characteristics were carried out through the sectioned and macerated wood samples. The obser ved characteristics of the anatomical features were defined conforming to the IAWA List of Microscopic Features for Hardwood  Identification.  Based on the scrutiny on those obser ved characteristics and linked to the fiber quality, it was judged that the fiber in all the five wood species could be classified as class I for pulp and paper processing.

Differential growth responses to water balance of coexisting deciduous tree species are linked to wood density in a Bolivian tropical dry forest.

Science.gov (United States)

Mendivelso, Hooz A; Camarero, J Julio; Royo Obregón, Oriol; Gutiérrez, Emilia; Toledo, Marisol

2013-01-01

A seasonal period of water deficit characterizes tropical dry forests (TDFs). There, sympatric tree species exhibit a diversity of growth rates, functional traits, and responses to drought, suggesting that each species may possess different strategies to grow under different conditions of water availability. The evaluation of the long-term growth responses to changes in the soil water balance should provide an understanding of how and when coexisting tree species respond to water deficit in TDFs. Furthermore, such differential growth responses may be linked to functional traits related to water storage and conductance. We used dendrochronology and climate data to retrospectively assess how the radial growth of seven coexisting deciduous tree species responded to the seasonal soil water balance in a Bolivian TDF. Linear mixed-effects models were used to quantify the relationships between basal area increment and seasonal water balance. We related these relationships with wood density and sapwood production to assess if they affect the growth responses to climate. The growth of all species responded positively to water balance during the wet season, but such responses differed among species as a function of their wood density. For instance, species with a strong growth response to water availability averaged a low wood density which may facilitate the storage of water in the stem. By contrast, species with very dense wood were those whose growth was less sensitive to water availability. Coexisting tree species thus show differential growth responses to changes in soil water balance during the wet season. Our findings also provide a link between wood density, a trait related to the ability of trees to store water in the stem, and wood formation in response to water availability.

Chemical investigation on wood tree species in a temperate forest, east-northern Romania

Directory of Open Access Journals (Sweden)

Teaca, C. A.

2007-02-01

Full Text Available A quantitative evaluation of wood chemical components for some tree species in a forest area from east-northern Romania is presented here, through a comparative study from 1964 to 2000. Investigation upon the wood tree-rings in a Quercus robur L. tree species, as a dominant species, as regards its chemical composition and structure of the natural polymer constituents - cellulose and lignin - was also performed through chemical methods to separate the main wood components, FT-IR spectroscopy, and thermogravimetry. Having in view the impact of climate and external factors (such as pollutant depositions, some possible correlations between wood chemical composition and its further use can be made. The FT-IR spectra give evidence of differences in the frequency domains of 3400-2900 cm-1 and 1730-1640 cm-1, due to some interactions between the chemical groups (OH, C=O. The crystallinity index of cellulose presents variations in the oak wood tree-rings. Thermogravimetry analyses show different behaviour of cellulose at thermal decomposition, as a function of radial growth and tree’s height. A preliminary chemical investigation of oak wood sawdust shows a relatively high content of mineral elements (ash, compared with a previous study performed in 1964, fact that may indicate an intense drying process of the oak tree, a general phenomenon present in European forests for this species.

Wood-thermoplastic composites manufactured using beetle-killed spruce from Alaska

Science.gov (United States)

V. Yadama; Eini Lowell; N. Petersen; D. Nicholls

2009-01-01

The primary objectives of the study were to characterize the critical properties of wood flour produced using highly deteriorated beetle-killed spruce for wood-plastic composite (WPC) production and evaluate important mechanical and physical properties of WPC extruded using an industry standard formulation. Chemical composition analysis indicated no significant...

Adaptability to climate change in forestry species: drought effects on growth and wood anatomy of ponderosa pines growing at different competition levels

Energy Technology Data Exchange (ETDEWEB)

Fernandez, M. E.; Gyenge, J. E.; Urquiza, M. M.; Varela, S.

2012-11-01

More stressful conditions are expected due to climatic change in several regions, including Patagonia, South-America. In this region, there are no studies about the impact of severe drought events on growth and wood characteristics of the most planted forestry species, Pinus ponderosa (Doug. ex-Laws). The objective of this study was to quantify the effect of a severe drought event on annual stem growth and functional wood anatomy of pines growing at different plantation densities aiming to understand how management practices can help to increase their adaptability to climate change. Growth magnitude and period, specific hydraulic conductivity, and anatomical traits (early- and late wood proportion, lumen diameter, cell-wall thickness, tracheid length and bordered pit dimensions) were measured in the ring 2008-2009, which was formed during drought conditions. This drought event decreased annual stem growth by 30-38% and 58-65% respect to previous mean growth, in open vs. closed stand trees, respectively, indicating a higher sensitivity of the latter, which is opposite to reports from the same species growing in managed native forests in USA. Some wood anatomical variables did differ in more water stressed trees (lower cell wall thickness of early wood cells and higher proportion of small-lumen cells in late wood), which in turn did not affect wood function (hydraulic conductivity and resistance to implosion). Other anatomical variables (tracheid length, pit dimensions, early- and late wood proportion, lumen diameter of early wood cells) did not differ between tree sizes and plantation density. The results suggest that severe drought affects differentially the amount but not the function and quality of formed wood in ponderosa pine growing at different competition levels. (Author) 41 refs.

USE OF AMAZONIAN SPECIES FOR AGING DISTILLED BEVERAGES: PHYSICAL AND CHEMICAL WOOD ANALYSIS

Directory of Open Access Journals (Sweden)

Jonnys Paz Castro

2015-06-01

Full Text Available The process of storing liquor in wooden barrels is a practice that aims to improve the sensory characteristics, such as color, aroma and flavor, of the beverage. The quality of the liquor stored in these barrels depends on wood characteristics such as density, permeability, chemical composition, anatomy, besides the wood heat treatment used to fabricate the barrels. Brazil has a great diversity of forests, mainly in the north, in the Amazon. This region is home to thousands of tree species, but is limited to the use of only a few native species to store liquors. The objective of this study was to determine some of the physical and chemical characteristics for four Amazon wood species. The results obtained in this study will be compared with others from woods that are traditionally used for liquor storage. The species studied were angelim-pedra (Hymenolobium petraeum Ducke cumarurana (Dipteryx polyphylla (Huber Ducke, jatobá (Hymenaea courbaril L. and louro-vermelho (Nectandra rubra (Mez CK Allen. The trees were collected from Precious Woods Amazon Company forest management area, in Silves, Amazonas. Analyzes such as: concentration of extractives, lignin amount, percentage of minerals (ash and tannin content, density, elemental analysis (CHNS-O and thermal analysis were done. It was observed that the chemical composition (lignin, holocellulose and elemental analysis (percentage of C, H, N and O of the woods have significant differences. The jatobá wood presented higher tannin content, and in the thermal analysis, was that which had the lowest mass loss.

DNA barcoding of vouchered xylarium wood specimens of nine endangered Dalbergia species

Science.gov (United States)

Min Yu; Lichao Jiao; Juan Guo; Alex C. Wiedenhoeft; Tuo He; Xiaomei Jiang; Yafang Yin

2017-01-01

ITS2+trnH-psbA was the best combination of DNA barcode to resolve the Dalbergia wood species studied. We demonstrate the feasibility of building a DNA barcode reference database using xylarium wood specimens.

Differential growth responses to water balance of coexisting deciduous tree species are linked to wood density in a Bolivian tropical dry forest.

Directory of Open Access Journals (Sweden)

Hooz A Mendivelso

Full Text Available A seasonal period of water deficit characterizes tropical dry forests (TDFs. There, sympatric tree species exhibit a diversity of growth rates, functional traits, and responses to drought, suggesting that each species may possess different strategies to grow under different conditions of water availability. The evaluation of the long-term growth responses to changes in the soil water balance should provide an understanding of how and when coexisting tree species respond to water deficit in TDFs. Furthermore, such differential growth responses may be linked to functional traits related to water storage and conductance. We used dendrochronology and climate data to retrospectively assess how the radial growth of seven coexisting deciduous tree species responded to the seasonal soil water balance in a Bolivian TDF. Linear mixed-effects models were used to quantify the relationships between basal area increment and seasonal water balance. We related these relationships with wood density and sapwood production to assess if they affect the growth responses to climate. The growth of all species responded positively to water balance during the wet season, but such responses differed among species as a function of their wood density. For instance, species with a strong growth response to water availability averaged a low wood density which may facilitate the storage of water in the stem. By contrast, species with very dense wood were those whose growth was less sensitive to water availability. Coexisting tree species thus show differential growth responses to changes in soil water balance during the wet season. Our findings also provide a link between wood density, a trait related to the ability of trees to store water in the stem, and wood formation in response to water availability.

Differential Growth Responses to Water Balance of Coexisting Deciduous Tree Species Are Linked to Wood Density in a Bolivian Tropical Dry Forest

Science.gov (United States)

Mendivelso, Hooz A.; Camarero, J. Julio; Royo Obregón, Oriol; Gutiérrez, Emilia; Toledo, Marisol

2013-01-01

A seasonal period of water deficit characterizes tropical dry forests (TDFs). There, sympatric tree species exhibit a diversity of growth rates, functional traits, and responses to drought, suggesting that each species may possess different strategies to grow under different conditions of water availability. The evaluation of the long-term growth responses to changes in the soil water balance should provide an understanding of how and when coexisting tree species respond to water deficit in TDFs. Furthermore, such differential growth responses may be linked to functional traits related to water storage and conductance. We used dendrochronology and climate data to retrospectively assess how the radial growth of seven coexisting deciduous tree species responded to the seasonal soil water balance in a Bolivian TDF. Linear mixed-effects models were used to quantify the relationships between basal area increment and seasonal water balance. We related these relationships with wood density and sapwood production to assess if they affect the growth responses to climate. The growth of all species responded positively to water balance during the wet season, but such responses differed among species as a function of their wood density. For instance, species with a strong growth response to water availability averaged a low wood density which may facilitate the storage of water in the stem. By contrast, species with very dense wood were those whose growth was less sensitive to water availability. Coexisting tree species thus show differential growth responses to changes in soil water balance during the wet season. Our findings also provide a link between wood density, a trait related to the ability of trees to store water in the stem, and wood formation in response to water availability. PMID:24116001

Long-term performance of thermoplastic composite material with cotton burr and stem (CBS) as a partial filler

Science.gov (United States)

Rationale: Cotton burr and stem (CBS) fraction of cotton gin byproducts has shown promise as a fiber filler in thermoplastic composites, with physical and mechanical properties comparable to that made with wood fiber fillers. However, the long-term performance of this composite material is not known...

Chemical composition of particles from traditional burning of Pakistani wood species

Science.gov (United States)

Shahid, Imran; Kistler, Magdalena; Mukhtar, Azam; Ramirez-Santa Cruz, Carlos; Bauer, Heidi; Puxbaum, Hans

2015-11-01

Total particulate matter (TPM) emitted during burning of three types of Pakistani wood (eucalyptus camaldulensis, local name Safeeda; acacia nilotica, local name Kikar, Babul; dalbergia sissoo, Shisham, Tali) in a traditional brick stove were collected and analyzed for anhydrosugars, sugar alcohols, trace metals, soluble ions and carbonaceous species. This is a first study reporting anhydrosugars in wood smoke particles emitted during traditional burning of common wood types in Pakistan. Carbonaceous species showed the highest contribution to the particulate matter. Although the total carbon (TC) contribution was similar for all burnings (64.8-70.2%), the EC/OC ratio varied significantly, from 0.2 to 0.3 for Accacia and Dalbergia to 0.7-0.8 for Eucalyptus and Wood-mix. Among inorganic constituents potassium chloride and silicon were found at levels higher than 1%. The levoglucosan concentrations ranged from 3.0 to 6.6% (average 5.6%) with the highest value for Accacia and lowest value for the wood-mix. The high levoglucosan/mannosan ratios of 20-28 were typical for hardwood. The ratio between levoglucosan and galactosan varied stronger and was found to be around 13-20 for Accacia, Eucalyptus and Wood mix, and 43 for Dalbergia. The determined levoglucosan concentrations allowed assessing the conversion factor for calculation of biomass smoke contribution to ambient particulate matter levels in Pakistan.

Wood Volume Production and Use of 10 Woody Species in Semiarid Zones of Northeastern Mexico

Directory of Open Access Journals (Sweden)

Rahim Foroughbakhch

2012-01-01

Full Text Available A research strategy was established to analyze the structure of timber trees in terms of forest productivity (volume and wood density of 10 species. The native species Acacia farnesiana, Acacia schaffneri, Bumelia celastrina, Cercidium macrun, Condalia hookeri, Ebenopsis ebano, Helietta parvifolia, and Prosopis laevigata and the exotic species Eucalyptus camaldulensis and Leucaena leucocephala were chosen due to their ecological and economic importance to the rural villages of northeastern Mexico. Measurements of different growth parameters and volume of trees were evaluated. The introduced species E. camaldulensis and L. leucocephala showed the best performance in wood volume production per tree and per hectare when compared to the native species. Likewise, among the native species, E. ebano, P. laevigata, C. hookeri, and A. farnesiana tended to show better characteristics in terms of wood volume production in comparison to H. parvifolia, A. schaffneri, C. macrum, and B. celastrina. Results showed a high diversity on the properties studied. The high biomass produced by most of the species considered in this study revealed their great energetic potential when used as wood and firewood or vegetal charcoal.

Wood construction under cold climate

DEFF Research Database (Denmark)

Wang, Xiaodong; Hagman, Olle; Sundqvist, Bror

2014-01-01

As wood constructions increasingly use engineered wood products worldwide, concerns arise about the integrity of the wood and adhesives system. The glueline stability is a crucial issue for engineered wood application, especially under cold climate. In this study, Norway spruce (Picea abies...... affected shear strength of wood joints. As temperature decreased, the shear strength decreased. PUR resin resulted in the strongest shear strength at all temperatures tested. MF resin responded to temperature changes in a similar ways as the PUR resin. The shear strength of wood joints with EPI resins...... specimens need to be tested in further work to more completely present the issue. The EN 301 and EN 302 may need to be specified based on wood species....

Adhesion quality of glued joints from different commercial wood species

Directory of Open Access Journals (Sweden)

Alexandre Miguel do Nascimento

2013-12-01

Full Text Available The objective of this study was to determine the effect of wood density, adhesive type and gluing pressure on the shear strength of glued joints of fourteen commercial wood species. Wood pieces were classified in three density classes (Class 1: less than 0.55 g cm-3; Class 2: from 0.55 to 0.75 g cm-3; and Class 3: greater than 0.75 g cm-3 and joints bonded with two adhesives: polyvinyl acetate (PVA and urea-formaldehyde (UF, under two different pressures: 6 and 12 kgf cm-2. Glued joints bonded with PVA adhesive presented higher shear strength than those bonded with UF adhesive. For percentage of wood failure, the PVA adhesive had the best performance, however, only Classes 1 and 2 reached the values required by ASTM 3110 standard. Glued joints from Class 3, bonded with UF adhesive, did not reach the values of solid wood. The gluing pressure of 12 kgf cm-2 was more efficient for Class 3, for both shear strength and percentage of wood failure.

An Ethnobotanical Survey on Fuel Wood and Timber plant Species ...

African Journals Online (AJOL)

Yomi

2011-12-19

Dec 19, 2011 ... 3Department of Botany, Post Graduate College Abbottabad, Pakistan. Accepted 17 March, 2011. A survey was conducted to explore the fuel wood species and timber producing species of Kaghan valleys, Pakistan. Consumption pattern and impact on the forest resources were also taken into consideration.

Potential arsenic exposures in 25 species of zoo animals living in CCA-wood enclosures

International Nuclear Information System (INIS)

Gress, J.; Silva, E.B. da; Oliveira, L.M. de; Zhao, Di; Anderson, G.; Heard, D.; Stuchal, L.D.; Ma, L.Q.

2016-01-01

Animal enclosures are often constructed from wood treated with the pesticide chromated copper arsenate (CCA), which leaches arsenic (As) into adjacent soil during normal weathering. This study evaluated potential pathways of As exposure in 25 species of zoo animals living in CCA-wood enclosures. We analyzed As speciation in complete animal foods, dislodgeable As from CCA-wood, and As levels in enclosure soils, as well as As levels in biomarkers of 9 species of crocodilians (eggs), 4 species of birds (feathers), 1 primate species (hair), and 1 porcupine species (quills). Elevated soil As in samples from 17 enclosures was observed at 1.0–110 mg/kg, and enclosures housing threatened and endangered species had As levels higher than USEPA's risk-based Eco-SSL for birds and mammals of 43 and 46 mg/kg. Wipe samples of CCA-wood on which primates sit had dislodgeable As residues of 4.6–111 μg/100 cm 2 , typical of unsealed CCA-wood. Inorganic As doses from animal foods were estimated at 0.22–7.8 μg/kg bw/d. Some As levels in bird feathers and crocodilian eggs were higher than prior studies on wild species. However, hair from marmosets had 6.37 mg/kg As, 30-fold greater than the reference value, possibly due to their inability to methylate inorganic As. Our data suggested that elevated As in soils and dislodgeable As from CCA-wood could be important sources of As exposure for zoo animals. - Highlights: • Daily inorganic As dose from zoo animal foods was 0.22–7.8 μg/kg bw/day. • Total As concentrations in soils of zoo animal enclosures were 1.0–110 mg/kg. • Endangered zoo animals live in soils with As above USEPA Eco-SSLs for avian and mammal species. • Dislodgeable As on CCA-wood beams where primates sit was 4.6–111 μg/100 cm 2 . • Marmoset hair had 6.37 mg/kg As compared to a reference value of 0.21 mg/kg.

Potential arsenic exposures in 25 species of zoo animals living in CCA-wood enclosures

Energy Technology Data Exchange (ETDEWEB)

Gress, J. [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Jiangsu 201146 (China); Soil and Water Science Department, University of Florida, Gainesville, FL 32611 (United States); Silva, E.B. da; Oliveira, L.M. de [Soil and Water Science Department, University of Florida, Gainesville, FL 32611 (United States); Zhao, Di [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Jiangsu 201146 (China); Anderson, G. [Virginia Polytechnic Institute and State University, Blacksburg, VA 24061 (United States); Heard, D. [Department of Small Animal Clinical Sciences, University of Florida, Gainesville, FL 32610 (United States); Stuchal, L.D. [Center for Environmental and Human Toxicology, University of Florida, Gainesville, FL 32611 (United States); Department of Environmental and Global Health, College of Public Health and Health Professions, University of Florida, Gainesville, FL 32611 (United States); Ma, L.Q., E-mail: lqma@ufl.edu [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Jiangsu 201146 (China); Soil and Water Science Department, University of Florida, Gainesville, FL 32611 (United States)

2016-05-01

Animal enclosures are often constructed from wood treated with the pesticide chromated copper arsenate (CCA), which leaches arsenic (As) into adjacent soil during normal weathering. This study evaluated potential pathways of As exposure in 25 species of zoo animals living in CCA-wood enclosures. We analyzed As speciation in complete animal foods, dislodgeable As from CCA-wood, and As levels in enclosure soils, as well as As levels in biomarkers of 9 species of crocodilians (eggs), 4 species of birds (feathers), 1 primate species (hair), and 1 porcupine species (quills). Elevated soil As in samples from 17 enclosures was observed at 1.0–110 mg/kg, and enclosures housing threatened and endangered species had As levels higher than USEPA's risk-based Eco-SSL for birds and mammals of 43 and 46 mg/kg. Wipe samples of CCA-wood on which primates sit had dislodgeable As residues of 4.6–111 μg/100 cm{sup 2}, typical of unsealed CCA-wood. Inorganic As doses from animal foods were estimated at 0.22–7.8 μg/kg bw/d. Some As levels in bird feathers and crocodilian eggs were higher than prior studies on wild species. However, hair from marmosets had 6.37 mg/kg As, 30-fold greater than the reference value, possibly due to their inability to methylate inorganic As. Our data suggested that elevated As in soils and dislodgeable As from CCA-wood could be important sources of As exposure for zoo animals. - Highlights: • Daily inorganic As dose from zoo animal foods was 0.22–7.8 μg/kg bw/day. • Total As concentrations in soils of zoo animal enclosures were 1.0–110 mg/kg. • Endangered zoo animals live in soils with As above USEPA Eco-SSLs for avian and mammal species. • Dislodgeable As on CCA-wood beams where primates sit was 4.6–111 μg/100 cm{sup 2}. • Marmoset hair had 6.37 mg/kg As compared to a reference value of 0.21 mg/kg.

Wood density and anatomy of three Eucalyptus species: implications for hydraulic conductivity

OpenAIRE

Antonio J. Barotto; Silvia Monteoliva; Javier Gyenge; Alejandro Martínez-Meier; Karen Moreno; Natalia Tesón; María Elena Fernández

2017-01-01

Aim of the study: To characterize wood anatomical traits of three Eucalyptus species that differ in wood density and ecological requirements, and to examine the relationships between some anatomical features, wood density, and theoretical xylem hydraulic conductivity (Ks). Area of study: We analyzed 86 trees from three sites of Argentina (Entre Ríos and Buenos Aires Provinces). Methods: The sampled trees were Eucalyptus globulus, E. grandis and E. viminalis ranging from 11 to 15 years...

The trait contribution to wood decomposition rates of 15 Neotropical tree species.

NARCIS (Netherlands)

van Geffen, K.G.; Poorter, L.; Sass-Klaassen, U.; van Logtestijn, R.S.P; Cornelissen, J.H.C.

2010-01-01

The decomposition of dead wood is a critical uncertainty in models of the global carbon cycle. Despite this, relatively few studies have focused on dead wood decomposition, with a strong bias to higher latitudes. Especially the effect of interspecific variation in species traits on differences in

Determination of the elemental composition of some lesser-used Ghanaian wood species by neutron activation analysis

International Nuclear Information System (INIS)

Nyarko, B.J.B.; Serfor-Armah, Y.; Adomako, D.; Andam, A.A.B.; Addison, E.C.K.; Ofori, J.; Cobbinah, J.R.

2003-01-01

Wood plays an undisputed socio-economic role in human endeavour. The elemental composition of wood can give an indication of the environmental pollution of the locality from which the wood sample was extracted as timber, and can influence the machining characteristics of timber. Additionally, the elemental composition can be used as an index of the nutrient uptake of plants from the soil. With the over-exploitation of timber species in Ghana, it is now imperative that lesser-used species are studied to know their characteristics for utilization. We report preliminary results of a study on the elemental composition of some lesser-used Ghanaian wood species. Ten Ghana wood species had been studied, namely: Strombosia glauscens, Lophira alata, Cynometra anata, Combretodendron macrocarpum, Sterculia rhinopetala, Celtis milbraedii, Celtis zenteri, Nesogoadonia papaverifa, Nauclea diderrichii, and Piptadeniastrum afrieana. Neutron activation analysis was carried out for this work, using the Ghana Research Reactor, (GHARRI) facility, operating between 3-15kw and at a thermal neutron flux of 1-5 x 10 15 ns -1 cm 2 . A total of twenty-five elements were identified, some at high level, others at trace levels. We discuss the implications of these results for the efficient utilization of lesser-used Ghana wood species (author)

An Ethnobotanical Survey on Fuel Wood and Timber plant Species ...

African Journals Online (AJOL)

A survey was conducted to explore the fuel wood species and timber producing species of Kaghan valleys, Pakistan. Consumption pattern and impact on the forest resources were also taken into consideration. A questionnaire was used as a survey instrument to obtain desired data. For this study, 10 villages were randomly ...

Drivers of CO2 Emission Rates from Dead Wood Logs of 13 Tree Species in the Initial Decomposition Phase

Directory of Open Access Journals (Sweden)

Tiemo Kahl

2015-07-01

Full Text Available Large dead wood is an important structural component of forest ecosystems and a main component of forest carbon cycles. CO2 emissions from dead wood can be used as a proxy for actual decomposition rates. The main drivers of CO2 emission rates for dead wood of temperate European tree species are largely unknown. We applied a novel, closed chamber measurement technique to 360 dead wood logs of 13 important tree species in three regions in Germany. We found that tree species identity was with 71% independent contribution to the model (R2 = 0.62 the most important driver of volume-based CO2 emission rates, with angiosperms having on average higher rates than conifers. Wood temperature and fungal species richness had a positive effect on CO2 emission rates, whereas wood density had a negative effect. This is the first time that positive fungal species richness—wood decomposition relationship in temperate forests was shown. Certain fungal species were associated with high or low CO2 emission rates. In addition, as indicated by separate models for each tree species, forest management intensity, study region, and the water content as well as C and N concentration of dead wood influenced CO2 emission rates.

Wood density and anatomy of three Eucalyptus species: implications for hydraulic conductivity

OpenAIRE

Barotto, Antonio J.; Monteoliva, Silvia; Gyenge, Javier; Martínez-Meier, Alejandro; Moreno, Karen; Tesón, Natalia; Fernández, María Elena

2017-01-01

Aim of the study: To characterize wood anatomical traits of three Eucalyptus species that differ in wood density and ecological requirements, and to examine the relationships between some anatomical features, wood density, and theoretical xylem hydraulic conductivity (Ks).Area of study: We analyzed 86 trees from three sites of Argentina (Entre Ríos and Buenos Aires Provinces).Methods: The sampled trees were Eucalyptus globulus, E. grandis and E. viminalis ranging from 11 to 15 years old. One ...

Species selection in secondary wood products: implications for product design and promotion

Science.gov (United States)

Matthew S. Bumgardner; Scott A. Bowe; Scott A. Bowe

2002-01-01

This study investigated the perceptions that people have of several commercially important wood species and determined if word-based and specimen-based evaluations differed. Such knowledge can help secondary wood manufacturers better understand their products and develop more effective design concepts and promotional messages. A sample of more than 250 undergraduate...

ANATOMICAL CHARACTERISTICS AND CHEMICAL PROPERTIES OF THE BRANCH-WOOD OF Schizolobium amazonicum DUCKE SPECIES AND ITS POTENTIAL USES

Directory of Open Access Journals (Sweden)

Yusup Amin

2013-10-01

Full Text Available The scale of forest degradation and deforestation in Indonesia has inspired the use of lesser-known wood species, which are potentially abundant and so far has not much been utilized. Utilization of these woods should be imposed not only of the stem wood but also of the branch-wood portions. Schizolobiumamazonicum Ducke treeis one of those lesser-known species, and growing fast with an MAIof3.68 cm/year.In Indonesia this species is only found in the Purwodadi Botanical Garden. A research was conducted to study the basic characteristics (anatomical aspects and chemical properties of the branch-wood portion of this species. The branch-wood materials were obtained from the Purwodadi Botanical Garden situated in Pasuruan (East Java. The specimens used were the first branch of the trunk (stem of nine-year old S. amazonicum tree (= 29.46 cm. The branch-wood samples were then examined for the anatomical aspects (macroscopic and microscopic characteristics and chemical properties (chemical composition. Results revealed that the anatomical properties of S.amazonicum branch-wood exhibited close similarities to those of sengon wood; it was light in appearance and white in color. Its fiber averaged about 1500 μm, and based on the fiber dimension's derived values the branch- wood fiber of this species was categorized into first-class quality for pulp and paper manufacture. Further, the chemical composition of this branch-wood compared favorably with that of sengon and mangium wood. The composition of extractive content thatsoluble in alcohol-benzene; lignin; holocellulose; and α-cellulose of this branch-wood were 2.46; 28.71; 80.64; and 50.47%, respectively. The overall assessment implied that the branch-wood portion of S.amazonicum tree affords favorable potential to be developed as raw material for pulp and paper manufacture. Also, considering that both sengon and mangium woods were already used in the pulp and paper industries as well as the trees are

Preferences of Coptotermes formosanus Shiraki and Coptotermes gestroi (Wasmann (Blattodea: Rhinotermitidae among Three Commercial Wood Species

Directory of Open Access Journals (Sweden)

Nirmala K. Hapukotuwa

2011-11-01

Full Text Available The Formosan subterranean termite, Coptotermes formosanus Shiraki, and the Asian subterranean termite, Coptotermes gestroi (Wasmann, are both pests of wood in service in Hawaii and Florida. We conducted a laboratory study using method modified from those described in standard E1-09 of the American Wood Protection Association (AWPA 2009 to assess the termite resistance of three commercially available wood species used in regions of the USA where both termite species occur: Douglas fir, Pseudotsuga menziessii, southern yellow pine, Pinus spp. and redwood, Sequoia sempervirens. A multiple-choice (three-choice assay was used for four weeks (28 days in order to simulate field conditions of food choice and assess termite feeding preferences under 28 °C and 72–80% RH. 400 termites (360 workers: 40 soldiers were released into each test jar. Five replicates and two controls of each wood species were used with each termite species. Termite mortality was recorded at the end of the test; and wood wafers were oven-dried and weighed before and after termite exposure to determine the mass loss due to termite feeding, and rated visually on a 0 (failure to 10 (sound scale. There were significant differences in mean mass loss values among the three wood species and between two termite species. The mean mass loss value for redwood was significantly lower than Douglas fir and southern yellow pine with both termite species. However, C. formosanus showed increased feeding on Douglas fir and southern yellow pine compared to C. gestroi.

Fuel Wood Consumption and Species Degradation in South-Western Nigeria: The Ecological Relevance

Directory of Open Access Journals (Sweden)

Orimoogunje Oluwagbenga O.I.

2015-01-01

Full Text Available The continuous dependence of man on fuel and service wood has resulted in serious degradation of the fragile forest ecosystem. Therefore, this study evaluated the sources and patterns of fuel wood and examined the rate of consumption in the study area. This was with the aim to assess the ecological implications of fuelwood consumption on species degradation. The study utilized both, primary and secondary data. Information was extracted from topographic map on the scale of 1: 50,000 and satellites imageries that cover the study area. Questionnaire administration, field observation and weight measurement of fuel wood were carried out. The results showed that the sources of fuel wood for domestic cooking were forest, nearby bush and abandoned farm while the sources of domestic energy were fuel wood (61.17%, charcoal (27%, kerosene (10%, electricity (1.33% and gas (0.5%. Fuel wood for small scale industries were: forest (49.23%, farmland (34.62 and fallow land (16.15%. The trend of fuel wood consumption was on the high side from 1995 to 2011, it was 58% in 1995, 70% in 2000, 82% in 2005 and 92% in 2010 and 2011 respectively. Many valuable economic tree species such as Triplochiton scleroxylon, Nesogordonia papaverifera, and Cordia spp. are near their extinction. Animals such as antelope, wolf and fox are going into extinction while monkey, grasscutter, hare, rabbit were endemic in the study area. The study concluded that the patterns of fuel wood use and fuel wood saturation presents a great danger for biodiversity products and services.

Preparation of starch-g-polyacrylamide and its utilization as an adhesive for wood, paper and glass

International Nuclear Information System (INIS)

Abu-Ayana, Y.M.; Abou Zeid, N.Y.; Asran, A.Sh.; Aly, A.S.

2005-01-01

Starch- based adhesives are capable of wetting polar surfaces such as cellulose, penetrating pores, and forming strong bonds through mechanical and physical bonds. This paper studies the modification of starch by grafting with acrylamide, and the relation between modification and adhesion properties. Six formulae are prepared from modified and unmodified starch, and evaluated as adhesives for wood, glass, carton, and paper. Study of the factors affecting the adhesive bond is performed. Promising results are obtained. The adhesive formulae I-VI can be used successfully as paper and carton adhesives. Formulae I, TI and III can be used as wood adhesives. Excellent value for shear strength using formula No. I, comparable with other known thermoplastic and thermoset adhesives., formula I also can be used as glass adhesive, but in narrow applications and in absence of water

Controls on coarse wood decay in temperate tree species: birth of the LOGLIFE experiment.

Science.gov (United States)

Cornelissen, Johannes H C; Sass-Klaassen, Ute; Poorter, Lourens; van Geffen, Koert; van Logtestijn, Richard S P; van Hal, Jurgen; Goudzwaard, Leo; Sterck, Frank J; Klaassen, René K W M; Freschet, Grégoire T; van der Wal, Annemieke; Eshuis, Henk; Zuo, Juan; de Boer, Wietse; Lamers, Teun; Weemstra, Monique; Cretin, Vincent; Martin, Rozan; Ouden, Jan den; Berg, Matty P; Aerts, Rien; Mohren, Godefridus M J; Hefting, Mariet M

2012-01-01

Dead wood provides a huge terrestrial carbon stock and a habitat to wide-ranging organisms during its decay. Our brief review highlights that, in order to understand environmental change impacts on these functions, we need to quantify the contributions of different interacting biotic and abiotic drivers to wood decomposition. LOGLIFE is a new long-term 'common-garden' experiment to disentangle the effects of species' wood traits and site-related environmental drivers on wood decomposition dynamics and its associated diversity of microbial and invertebrate communities. This experiment is firmly rooted in pioneering experiments under the directorship of Terry Callaghan at Abisko Research Station, Sweden. LOGLIFE features two contrasting forest sites in the Netherlands, each hosting a similar set of coarse logs and branches of 10 tree species. LOGLIFE welcomes other researchers to test further questions concerning coarse wood decay that will also help to optimise forest management in view of carbon sequestration and biodiversity conservation.

Technological and Thermal Properties of Thermoplastic Composites Filled with Heat-treated Alder Wood

Directory of Open Access Journals (Sweden)

Mürşit Tufan

2016-02-01

Full Text Available This study investigated the effect of heat-treated wood content on the water absorption, mechanical, and thermal properties of wood plastic composites (WPCs. The WPCs were produced from various loadings (30, 40, and 50 wt% of heat-treated and untreated alder wood flours (Alnus glutinosa L. using high-density polyethylene (HDPE with 3 wt% maleated polyethylene (MAPE coupling agent. All WPC formulations were compression molded into a hot press for 3 min at 170 ºC. The WPCs were evaluated using mechanical testing, Fourier transform infrared spectroscopy (FTIR, thermogravimetric analysis (TGA, and differential scanning calorimetry (DSC. The mechanical property values of the WPC specimens decreased with increasing amounts of the heat-treated wood flour, except for the tensile modulus values. The heat treatment of alder wood slightly increased the thermal stability of the WPCs compared with the reference WPCs. The crystallization degree (Xc and the enthalpy of crystallization of the WPCs slightly decreased with increasing content of the heat-treated wood flour. However, all WPCs containing the heat-treated alder wood flour showed a higher crystallinity degree than that of the virgin HDPE.

Ecology, environmental requirements and conservation of corticioid fungi occupying small diameter dead wood

OpenAIRE

Juutilainen, Katja

2016-01-01

The increasing human impact upon the biosphere of earth is causing profound changes across all spatial scales. The ability to cope with human-induced disturbance varies among organisms; specialist species are more negatively affected than generalist species. Forests are among the most heavily affected ecosystems; especially the dead wood associated organisms are in peril. The earlier research has strongly focused on large diameter dead wood and associated species. The ...

Resistance of Particleboards Made from Fast-Growing Wood Species to Subterranean Termite Attack.

Science.gov (United States)

Hermawan, Dede; Hadi, Yusuf S; Fajriani, Esi; Massijaya, Muhamad Y; Hadjib, Nurwati

2012-05-29

Laboratory-made particleboards were tested for their resistance to subterranean termite, Coptotermes curvignathus Holmgren (Order Isoptera, Family Termitidae) by Indonesian standard SNI 01.7207-2006, during four weeks and at the end of the test their mass loss percentage and feeding rate were determined. Particleboards consisted of: jabon (Anthocephalus cadamba, Family Rubiacea) with a density of 0.41 g/cm³; sungkai (Peronema canescens, Family Verbenaceae) with a density of 0.46 g/cm³; mangium (Acacia mangium, Family Rhamnaceae) with a density of 0.60 g/cm³ separately and the three species mixture at a rate of 1:1:1. Densities of the boards were targetted at 0.60 g/cm³ and 0.80 g/cm³ by using 12% urea formaldehyde as binder with 2% paraffin as additive based on oven dry wood particle weight. The hand-formed mats and hot-pressing at 130 °C and 2.45 MPa for 10 min were applied. The results showed that particleboards density did not affect mass loss and feeding rate, but the particleboards made from higher density wood resulted in higher resistance to subterranean termite attack. The most resistant particleboards were made of magium, followed by sungkai, mixed species, and jabon.

Wood specific gravity and anatomy of branches and roots in 113 Amazonian rainforest tree species across environmental gradients.

Science.gov (United States)

Fortunel, Claire; Ruelle, Julien; Beauchêne, Jacques; Fine, Paul V A; Baraloto, Christopher

2014-04-01

Wood specific gravity (WSG) is a strong predictor of tree performance across environmental gradients. Yet it remains unclear how anatomical elements linked to different wood functions contribute to variation in WSG in branches and roots across tropical forests. We examined WSG and wood anatomy in white sand, clay terra firme and seasonally flooded forests in French Guiana, spanning broad environmental gradients found throughout Amazonia. We measured 15 traits relating to branches and small woody roots in 113 species representing the 15 most abundant species in each habitat and representative species from seven monophyletic lineages occurring in all habitats. Fiber traits appear to be major determinants of WSG, independent of vessel traits, in branches and roots. Fiber traits and branch and root WSG increased from seasonally flooded species to clay terra firme species and lastly to white sand species. Branch and root wood traits were strongly phylogenetically constrained. Lineages differed in wood design, but exhibited similar variation in wood structure across habitats. We conclude that tropical trees can invest differently in support and transport to respond to environmental conditions. Wind disturbance and drought stress represent significant filters driving tree distribution of Amazonian forests; hence we suggest that biophysical explanations should receive more attention. © 2013 The Authors. New Phytologist © 2013 New Phytologist Trust.

Photodegradation of two tropical wood species: jatoba (Hymenaea courbaril) and tauari (Couratari oblongifolia) submitted to ultraviolet radiation

International Nuclear Information System (INIS)

Costa, J. de A.; Gonçalez, J.C.; Camargos, J.A.A.

2011-01-01

The objective of this study was to follow the process of photodegradation of the natural color of wood surface of two tropical species when exposed to ultraviolet radiation. It were used the wood of jatobá (Hymenaea courbaril) with reddish brown coloration, and tauari (Couratari oblongifolia) with yellowish olive coloration. Samples of these woods were subjected to four cycles of ultraviolet radiation (UV) amounting to a total of 168 hours of irradiation and at 350 nm of wave length. Changes of the woods natural color, indicative of the photodegradation process, was monitored by spectrocolorimetry. Both species underwent changes in color caused by photodegradation, since the irradiation caused darkening which was quantified by the intensity of reflected light. Tauari demonstrated greater resistance to UV radiation and jatobá showed greater tendency to redden up. Both species were classified as woods with very appreciable variation in color [pt

Wood density explains architectural differentiation across 145 co-occurring tropical tree species

NARCIS (Netherlands)

Iida, Y.; Poorter, L.; Sterck, F.J.; Kubo, T.; Kassim, A.R.; Potts, M.D.; Kohyama, T.S.

2012-01-01

1. Because of its mechanical properties, wood density may affect the way that trees expand their stem and crown to exploit favourable light conditions in a mechanically stable way. From engineering theory and wood density properties, it is predicted that in terms of biomass investment, low-density

Simulated nitrogen deposition affects wood decomposition by cord-forming fungi.

Science.gov (United States)

Bebber, Daniel P; Watkinson, Sarah C; Boddy, Lynne; Darrah, Peter R

2011-12-01

Anthropogenic nitrogen (N) deposition affects many natural processes, including forest litter decomposition. Saprotrophic fungi are the only organisms capable of completely decomposing lignocellulosic (woody) litter in temperate ecosystems, and therefore the responses of fungi to N deposition are critical in understanding the effects of global change on the forest carbon cycle. Plant litter decomposition under elevated N has been intensively studied, with varying results. The complexity of forest floor biota and variability in litter quality have obscured N-elevation effects on decomposers. Field experiments often utilize standardized substrates and N-levels, but few studies have controlled the decay organisms. Decomposition of beech (Fagus sylvatica) blocks inoculated with two cord-forming basidiomycete fungi, Hypholoma fasciculare and Phanerochaete velutina, was compared experimentally under realistic levels of simulated N deposition at Wytham Wood, Oxfordshire, UK. Mass loss was greater with P. velutina than with H. fasciculare, and with N treatment than in the control. Decomposition was accompanied by growth of the fungal mycelium and increasing N concentration in the remaining wood. We attribute the N effect on wood decay to the response of cord-forming wood decay fungi to N availability. Previous studies demonstrated the capacity of these fungi to scavenge and import N to decaying wood via a translocating network of mycelium. This study shows that small increases in N availability can increase wood decomposition by these organisms. Dead wood is an important carbon store and habitat. The responses of wood decomposers to anthropogenic N deposition should be considered in models of forest carbon dynamics.

Nutritional ecology of the formosan subterranean termite (Isoptera: Rhinotermitidae): feeding response to commercial wood species.

Science.gov (United States)

Morales-Ramos, J A; Rojas, M G

2001-04-01

The feeding preferences of the Formosan subterranean termite, Coptotermes formosanus Shiraki, were tested in three separate experiments on 28 different wood species. Experiment 1 was a multiple-choice test designed to test relative preferences among 24 wood species commercially available in New Orleans, LA. Experiment 2 was a similar study designed to test relative preferences among 21 wood species shown or reported to be unpalatable to the Formosan subterranean termite. Experiment 3 was a no-choice test to examine the feeding deterrence of the 10 least preferred wood species. Preference was determined by consumption rates. Birch (Betula alleghaniensis Britton), red gum (Liquidambar styraciflua L.), Parana pine [Araucaria angustifolia (Bert.) 1, sugar maple (Acer saccharum Marsh.), pecan (Carya illinoensis Wangenh.), and northern red oak (Quercus rubra L.) were the most preferred species by C. formosanus in order of consumption rate. All of these species were significantly more preferred than southern yellow pine (Pinus taeda L.), widely used for monitoring. Sinker cypress [ = old growth bald cypress, Taxodium distichum (L.)], western red cedar (Thuja plicata Donn), Alaskan yellow cedar (Chamaecyparis nootkatensis D. Don), eastern red cedar (Juniperus virginiana L.), sassafras [Sassafras albidum (Nutt.)], Spanish cedar (Cedrella odorata L.), Honduras mahogany (Swietenia macrophyla King), Indian rosewood (Dalbergia latifolia Roxb.), Honduras rosewood (D. stevensonii Standl.), and morado (Machaerium sp.) induced significant feeding deterrence and mortality to C. formosanus. The last eight species produced 100% mortality after 3 mo.

Termites amplify effects of wood traits on decomposition rates among multiple bamboo and dicot woody species

NARCIS (Netherlands)

Liu, Guofang; Cornwell, W.K.; Cao, Kunfang; Hu, Yukun; van Logtestijn, R.S.P; Yang, Shijian; Xie, Xiufang; Zhang, Yalin; Ye, Duo; Pan, Xu; Ye, Xuehua; Huang, Zhenying; Dong, Ming; Cornelissen, J.H.C.

2015-01-01

Wood decomposition is a key process in the terrestrial carbon cycle, controlling carbon storage with feedback to climate. In (sub) tropical forest, termites are major players in wood decomposition, but their role relative to that of microbial decomposers and wood traits of different tree species is

DNA Barcode Authentication and Library Development for the Wood of Six Commercial Pterocarpus Species: the Critical Role of Xylarium Specimens.

Science.gov (United States)

Jiao, Lichao; Yu, Min; Wiedenhoeft, Alex C; He, Tuo; Li, Jianing; Liu, Bo; Jiang, Xiaomei; Yin, Yafang

2018-01-31

DNA barcoding has been proposed as a useful tool for forensic wood identification and development of a reliable DNA reference library is an essential first step. Xylaria (wood collections) are potentially enormous data repositories if DNA information could be extracted from wood specimens. In this study, 31 xylarium wood specimens and 8 leaf specimens of six important commercial species of Pterocarpus were selected to investigate the reliability of DNA barcodes for authentication at the species level and to determine the feasibility of building wood DNA barcode reference libraries from xylarium specimens. Four DNA barcodes (ITS2, matK, ndhF-rpl32 and rbcL) and their combination were tested to evaluate their discrimination ability for Pterocarpus species with both TaxonDNA and tree-based analytical methods. The results indicated that the combination barcode of matK + ndhF-rpl32 + ITS2 yielded the best discrimination for the Pterocarpus species studied. The mini-barcode ndhF-rpl32 (167-173 bps) performed well distinguishing P. santalinus from its wood anatomically inseparable species P. tinctorius. Results from this study verified not only the feasibility of building DNA barcode libraries using xylarium wood specimens, but the importance of using wood rather than leaves as the source tissue, when wood is the botanical material to be identified.

Production of oriented strand board using four wood species from forest plantations

Directory of Open Access Journals (Sweden)

Setsuo Iwakiri

2014-06-01

Full Text Available This study aimed to evaluate the feasibility of using wood of Acrocarpus fraxinifolius, grevílea robusta, Melia azedarach, Toona ciliata, and mixture of these species for OSB manufacturing. The panels were produced in the laboratory with a nominal density of 0.80 g / cm ³, using phenol-formaldehyde resin in an amount of 6% of solid resin. There were evaluated the properties of water absorption and thickness swelling - 2 and 24 hours, internal bond, modulus of elasticity and modulus of rupture in the parallel and perpendicular direction, according to EN standards. The OSB panels produced with four species and the mixture of these species showed average values of mechanical properties above the minimum standard established by the CSA 437/1993. The results of the physical and mechanical properties obtained indicate the feasibility of the use of wood of Acrocarpus fraxinifolius, grevílea robusta, Melia azedarach and Toona ciliata, and mixture of these species for OSB manufacturing.

Resistance of Particleboards Made from Fast-Growing Wood Species to Subterranean Termite Attack

Directory of Open Access Journals (Sweden)

Nurwati Hadjib

2012-05-01

Full Text Available Laboratory-made particleboards were tested for their resistance to subterranean termite, Coptotermes curvignathus Holmgren (Order Isoptera, Family Termitidae by Indonesian standard SNI 01.7207–2006, during four weeks and at the end of the test their mass loss percentage and feeding rate were determined. Particleboards consisted of: jabon (Anthocephalus cadamba, Family Rubiacea with a density of 0.41 g/cm³; sungkai (Peronema canescens, Family Verbenaceae with a density of 0.46 g/cm³; mangium (Acacia mangium, Family Rhamnaceae with a density of 0.60 g/cm³ separately and the three species mixture at a rate of 1:1:1. Densities of the boards were targetted at 0.60 g/cm³ and 0.80 g/cm³ by using 12% urea formaldehyde as binder with 2% paraffin as additive based on oven dry wood particle weight. The hand-formed mats and hot-pressing at 130 °C and 2.45 MPa for 10 min were applied. The results showed that particleboards density did not affect mass loss and feeding rate, but the particleboards made from higher density wood resulted in higher resistance to subterranean termite attack. The most resistant particleboards were made of magium, followed by sungkai, mixed species, and jabon.

Comparison of Different Wood Species as Raw Materials for Bioenergy

Directory of Open Access Journals (Sweden)

Bojana Klašnja

2013-12-01

Full Text Available Background and Purpose: Most projections of the global energy use predict that biomass will be an important component of primary energy sources in the coming decades. Short rotation plantations have the potential to become an important source of renewable energy in Europe because of the high biomass yields, a good combustion quality as solid fuel, ecological advantages and comparatively low biomass production costs. Materials and Methods: In this study, the wood of black locust Robinia pseudoacacia, white willow Salix alba L., poplars Populus deltoides and Populus x euramericana cl.I-214, aged eight years were examined. Immediately after the felling, sample discs were taken to assess moisture content, ash content, the width of growth rings, wood densities and calorific values, according to the standard methodology. Results:The mean values of willow, poplar and black locust wood density were 341 kg/m3, 336 kg/m3 and 602 kg/m3,respectively. The average heating values of willow poplar and black locust wood were 18.599 MJ/kg, 18.564 MJ/kg and 21.196 MJ/kg, respectively. The FVI index (average values was higher for black locust (17.186 than for poplar and willow clones, which were similar: 11.312 and 11.422 respectively. Conclusions: Black locust wood with a higher density, calorific value and ash content compared to poplar and willow wood proved to be a more suitable raw material as RES. However, it is very important, from the aspect of the application of wood of these tree species as RES, to also consider the influence of the biomass yield per unit area of the plantations established as “energy plantations”.

Joining of thermoplastic substrates by microwaves

Science.gov (United States)

Paulauskas, Felix L.; Meek, Thomas T.

1997-01-01

A method for joining two or more items having surfaces of thermoplastic material includes the steps of depositing an electrically-conductive material upon the thermoplastic surface of at least one of the items, and then placing the other of the two items adjacent the one item so that the deposited material is in intimate contact with the surfaces of both the one and the other items. The deposited material and the thermoplastic surfaces contacted thereby are then exposed to microwave radiation so that the thermoplastic surfaces in contact with the deposited material melt, and then pressure is applied to the two items so that the melted thermoplastic surfaces fuse to one another. Upon discontinuance of the exposure to the microwave energy, and after permitting the thermoplastic surfaces to cool from the melted condition, the two items are joined together by the fused thermoplastic surfaces. The deposited material has a thickness which is preferably no greater than a skin depth, .delta..sub.s, which is related to the frequency of the microwave radiation and characteristics of the deposited material in accordance with an equation.

Identification of endangered or threatened Costa Rican tree species by wood anatomy and fluorescence activity.

Science.gov (United States)

Moya, Róger; Wiemann, Michael C; Olivares, Carlos

2013-09-01

A total of 45 native Costa Rican tree species are threatened or in danger of extinction, but the Convention on International Trade Endangered Species (CITES) includes only eight of these in its Appendices. However, the identification of other species based on their wood anatomy is limited. The present study objective was to describe and to compare wood anatomy and fluorescence activity in some endangered or threatened species of Costa Rica. A total of 45 (22 endangered and 23 threatened with extinction) wood samples of these species, from the xylaria of the Instituto Tecnológico de Costa Rica and the Forest Products Laboratory in Madison, Wisconsin, were examined. Surface fluorescence was positive in eight species, water extract fluorescence was positive in six species and ethanol extract fluorescence was positive in 24 species. Almost all species were diffuse porous except for occasional (Cedrela odorata, C. fissilis, Cordia gerascanthus) or regular (C. salvadorensis and C. tonduzii) semi-ring porosity. A dendritic vessel arrangement was found in Sideroxylon capari, and pores were solitary in Guaiacum sanctum and Vantanea barbourii. Vessel element length was shortest in Guaiacum sanctum and longest in Humiriastrum guianensis, Minquartia guianensis and Vantanea barbourii. Finally, anatomical information and fluorescence activity were utilized to construct an identification key of species, in which fluorescence is a feature used in identification.

Identification of endangered or threatened Costa Rican tree species by wood anatomy and fluorescence activity

Directory of Open Access Journals (Sweden)

Róger Moya

2013-09-01

Full Text Available A total of 45 native Costa Rican tree species are threatened or in danger of extinction, but the Convention on International Trade Endangered Species (CITES includes only eight of these in its Appendices. However, the identification of other species based on their wood anatomy is limited. The present study objective was to describe and to compare wood anatomy and fluorescence activity in some endangered or threatened species of Costa Rica. A total of 45 (22 endangered and 23 threatened with extinction wood samples of these species, from the xylaria of the Instituto Tecnológico de Costa Rica and the Forest Products Laboratory in Madison, Wisconsin, were examined. Surface fluorescence was positive in eight species, water extract fluorescence was positive in six species and ethanol extract fluorescence was positive in 24 species. Almost all species were diffuse porous except for occasional (Cedrela odorata, C. fissilis, Cordia gerascanthus or regular (C. salvadorensis and C. tonduzii semi-ring porosity. A dendritic vessel arrangement was found in Sideroxylon capari, and pores were solitary in Guaiacum sanctum and Vantanea barbourii. Vessel element length was shortest in Guaiacum sanctum and longest in Humiriastrum guianensis, Minquartia guianensis and Vantanea barbourii. Finally, anatomical information and fluorescence activity were utilized to construct an identification key of species, in which fluorescence is a feature used in identification.

BASIC DENSITY AND RETRACTIBILITY OF WOOD CLONES OF THREE Eucalyptus SPECIES

Directory of Open Access Journals (Sweden)

Djeison Cesar Batista

2010-12-01

Full Text Available Among the planted forests that supply the national wood industry, the genus Eucalyptus has become the most important, due to its fast growth, ease of large scale planting and variability of wood use. The generation of new hybrids and clones is a reality in the national practice of silviculture, and there is great interest currently in finding genetic improvements, mainly for higher volumetric gains and resistance in rough conditions of planting, such as pest attacks, periods of drought, low soil fertility, etc. The basic density is one of the most important physical properties of wood because it relates directly to other properties, including the anisotropic shrinkage. Such properties indicate the rational use of a species in a certain wood product. The aim of this work was to determine the basic density and the anisotropic shrinkage of five wood clones for each one of the following species: Eucalyptus saligna, Eucalyptus grandis and Eucalyptus dunnii. Clone 5 of Eucalyptus saligna presented the highest basic density (0.56 g/cm³ and was the most dimensionally instable. Of all the species, there was only a direct relation among basic density, maximum volumetric shrinkage and maximum volumetric shrinkage coefficient in this clone. Considering maximum volumetric shrinkage as the criterion, clone 3 was the most dimensionally stable. Clones 2 and 3 of Eucalyptus grandis presented the least and the highest basic density, respectively, with 0.40 and 0.49 g/cm³. It was not possible to distinguish among clones 1, 3 and 4 in terms of dimensional stability, and considering maximum volumetric shrinkage coefficient as the criterion, clone 5 was the most dimensionally instable. For Eucalyptus saligna and Eucalyptus dunnii it was not possible to distinguish which clone presented the least basic density. Clone 3 of Eucalyptus dunnii presented the highest basic density (0.65 g/cm³ and considering maximum volumetric shrinkage coefficient as the criterion, it

The influence of irradiated wood filler on some properties of polypropylene - wood composites

Directory of Open Access Journals (Sweden)

Điporović-Momčilović Milanka

2007-01-01

Full Text Available The problem of compatibility between the wood filler and thermoplastic matrix is of essential importance in composite production. Numerous methods have been developed for increasing this compatibility, which is still representing a challenging objective of composite research throughout the world. The research into these methods is primarily directed towards their efficiency from the viewpoint of the composite performance and their economical acceptability. The latter is of particular importance for the composite production in the developing countries with respect to the shortage of the corresponding funds. With this respect, the utilization of ionizing radiation might have considerable advantages. In this research, the beech wood flour was irradiated by a dose of 10 kGy of 60Co gamma rays for purpose of provoking the changes by the ionizing effect. The effects of ionizing radiation upon the properties of wood particles have been examined by IR spectroscopy and by determination of contents of hydroxyl groups in wood by acetylating as an indirect method. All these methods have been expected to reveal the chemical effects of the applied radiation treatment. The irradiated and the control wood flour were used in order to produce the samples of composite with polypropylene. The polypropylene-wood flour (PP-WF composites were produced with 40% of wood particles having fraction size 0.3 mm. The melt-blended composites were modified with amido-acrylic acid (AMACA as a new coupling agent synthesized for this propose in amount of 6 wt.% (based on wood filler and successively with 0.05 wt.% (based on PP of organic peroxide during mixing step. The composites containing coupling agents showed superior mechanical properties, compared to the untreated one. The highest extent of improvement of tensile was achieved in PP-WFl composites modified with AMACA coupling agent.

Hydraulic architecture of two species differing in wood density: opposing strategies in co-occurring tropical pioneer trees

Science.gov (United States)

Katherine A. McCulloh; Daniel M. Johnson; Frederick C. Meinzer; Steven L. Voelker; Barbara Lachenbruch; Jean-Christophe. Domec

2012-01-01

Co-occurring species often have different strategies for tolerating daily cycles of water stress. One underlying parameter that can link together the suite of traits that enables a given strategy is wood density. Here we compare hydraulic traits of two pioneer species from a tropical forest in Panama that differ in wood density: Miconia argentea...

PHYTOALEXIN DEFICIENT 4 affects reactive oxygen species metabolism, cell wall and wood properties in hybrid aspen (Populus tremula L. × tremuloides).

Science.gov (United States)

Ślesak, Ireneusz; Szechyńska-Hebda, Magdalena; Fedak, Halina; Sidoruk, Natalia; Dąbrowska-Bronk, Joanna; Witoń, Damian; Rusaczonek, Anna; Antczak, Andrzej; Drożdżek, Michał; Karpińska, Barbara; Karpiński, Stanisław

2015-07-01

The phytoalexin deficient 4 (PAD4) gene in Arabidopsis thaliana (AtPAD4) is involved in the regulation of plant--pathogen interactions. The role of PAD4 in woody plants is not known; therefore, we characterized its function in hybrid aspen and its role in reactive oxygen species (ROS)-dependent signalling and wood development. Three independent transgenic lines with different suppression levels of poplar PAD expression were generated. All these lines displayed deregulated ROS metabolism, which was manifested by an increased H2O2 level in the leaves and shoots, and higher activities of manganese superoxide dismutase (MnSOD) and catalase (CAT) in the leaves in comparison to the wild-type plants. However, no changes in non-photochemical quenching (NPQ) between the transgenic lines and wild type were observed in the leaves. Moreover, changes in the ROS metabolism in the pad4 transgenic lines positively correlated with wood formation. A higher rate of cell division, decreased tracheid average size and numbers, and increased cell wall thickness were observed. The results presented here suggest that the Populus tremula × tremuloides PAD gene might be involved in the regulation of cellular ROS homeostasis and in the cell division--cell death balance that is associated with wood development. © 2014 John Wiley & Sons Ltd.

Thermoplastic starch materials prepared from rice starch

International Nuclear Information System (INIS)

Pontes, Barbara R.B.; Curvelo, Antonio A.S.

2009-01-01

Rice starch is a source still little studied for the preparation of thermoplastic materials. However, its characteristics, such as the presence of proteins, fats and fibers may turn into thermoplastics with a better performance. The present study intends the evaluation of the viability of making starch thermoplastic from rice starch and glycerol as plasticizer. The results of X-ray diffraction and scanning electronic microscopy demonstrate the thermoplastic acquisition. The increase of plasticizer content brings on more hydrophilic thermoplastics with less resistance to tension and elongation at break. (author)

Identification and characterisation of factors affecting losses in the large-scale, non-ventilated bulk storage of wood chips and development of best storage practices

Energy Technology Data Exchange (ETDEWEB)

Garstang, J.; Weekes, A.; Poulter, R.; Bartlett, D.

2002-07-01

The report describes the findings of a study to determine the factors affecting the commercial storage of wood chips for biomass power generation in the UK. The UK's first such plant in North Yorkshire uses a mixture of forestry residues and short rotation coppice (SRC) willow, where problems with the stored fuel highlighted the need to determine best storage practices. Two wood chip piles were built (one with willow chip and the other with wood chips from board leaf forestry residues) and monitored (moisture, temperature, chemical composition, spore numbers and species, heat and air flows, bulk density, etc). Local weather data was also obtained. Recommendations for future storage practices are made.

Species selection in secondary wood products: perspectives from different consumers

Science.gov (United States)

Scott A. Bowe; Matthew S. Bumgardner; Matthew S. Bumgardner

2004-01-01

This study investigated adult consumer perceptions of several wood species to determine if word-based and appearance-based evaluations differed. The research replicated a 2001 study by the authors, which used undergraduate college students as a proxy for older and more experienced adult furniture consumers. The literature is somewhat inconclusive concerning the extent...

Radial variation in fiber length of some lesser used wood species in ...

African Journals Online (AJOL)

Variations in fibre length of ten lesser used wood species were investigated. The mean fibre length varied from 1.07mm in Lannea acida to 2.41mm in Sterculia setigera. Four patterns of within tree radial variations in fibre length were observed in the studied species. In pattern one, fibre length increased from the pith to the ...

WOOD PROPERTIES AND EFFECT OF WOOD PROPERTIES ON THE WOOD FINISHING

Directory of Open Access Journals (Sweden)

Abdulkadir Malkoçoğlu

2006-04-01

Full Text Available Wood is basic raw material for furniture and joinery industries with wood structures. Wood is a biological material that has widely different properties depending on species, geographic area where the tree grew, the growth condition, size of the tree at harvest, sawing, and other manufacturing processes. Wood properties have been characterized within two groups as natural and manufacturing factors that effects finishing performance. Grow rate, density, knots, moisture content, extractives and juvenile wood are natural characteristics. Grain orientation, texture, drying and performance expectations are manufacturing characteristics. In this review, the effects of natural and manufacturing characteristics are discussed on the surface finishing performance of wood.

WOOD ANATOMY OF TWO SPECIES OF THE GENUS Heterothalamus Lessing (ASTERACEAE FROM RIO GRANDE DO SUL (BRAZIL

Directory of Open Access Journals (Sweden)

Anabela Silveira de Oliveira

2010-08-01

Full Text Available The present work describes the wood anatomy of Heterothalamus alienus and Heterothalamus rupestris (Astereae - Asteraceae, as part of the secondary xylem study in the named genus. For the two species it was recorded some features usually mentioned in the literature for the Asteraceae, as typically small vessels, grouped in a dendritic pattern, the presence of only simple perforation plates and of paratracheal parenchyma. Heterothalamus alienus shows spiral thickenings in the wood vessels and storied vasicentric axial parenchyma. Heterothalamus rupestris differs itself by the absence of spiral thickenings in wood vessels and by no storied axial parenchyma, in paratracheal vasicentric to unilateral patterns. Photomicrographs, quantitative data of anatomical features and a comparison between the two  species of wood are also provided.

Factors affecting the availability of wood energy from nonindustrial private forest lands in the Northeast.

Science.gov (United States)

John J. Lindsay; Alphonse H. Gilbert; Thomas W. Birch; Thomas W. Birch

1992-01-01

Describes factors affecting the availability of fuelwood from nonindustrial private forests (NIPF) in the Northeast. The availability of market fuelwood depends heavily on tract size. The demand for land to supply the expanding urban fringe may result in a lower supply of market wood but also in more wood being cut to satisfy the owner's need for wood. NIPF owners...

Wood-polymer composites from Philippine tree plantation species by radiation polymerization I. Uptake and irradiation parameters

International Nuclear Information System (INIS)

Dela Rosa, A.M.; Castaneda, S.S.; Real, M.P.N.; Sta Ana, L.P.; Mosteiro, A.P.; Bauza, E.; Carandang, J.P.

1993-01-01

Radiation catalyzed polymerization of methyl methacrylate (MMA) in various Philippine tree plantation species were investigated. Wood samples measuring 1x6cm were impregnated with monomer at reduced pressure and gamma irradiated for various doses at a dose rate of 0.53 kGy/h. The parameters used to assess the polymerization reaction were the uptake of monomer by the wood samples, monomer conversion, and polymer loading in the irradiated samples. The uptake and polymerization data indicate that coconut wood, rubber wood, bagras, and Moluccan sau could be potential raw materials for the production of wood-polymer composites (WPC). (author). 6 refs.; 2 figs.; 1 tab

Salt stress induces the formation of a novel type of 'pressure wood' in two Populus species.

Science.gov (United States)

Janz, Dennis; Lautner, Silke; Wildhagen, Henning; Behnke, Katja; Schnitzler, Jörg-Peter; Rennenberg, Heinz; Fromm, Jörg; Polle, Andrea

2012-04-01

• Salinity causes osmotic stress and limits biomass production of plants. The goal of this study was to investigate mechanisms underlying hydraulic adaptation to salinity. • Anatomical, ecophysiological and transcriptional responses to salinity were investigated in the xylem of a salt-sensitive (Populus × canescens) and a salt-tolerant species (Populus euphratica). • Moderate salt stress, which suppressed but did not abolish photosynthesis and radial growth in P. × canescens, resulted in hydraulic adaptation by increased vessel frequencies and decreased vessel lumina. Transcript abundances of a suite of genes (FLA, COB-like, BAM, XET, etc.) previously shown to be activated during tension wood formation, were collectively suppressed in developing xylem, whereas those for stress and defense-related genes increased. A subset of cell wall-related genes was also suppressed in salt-exposed P. euphratica, although this species largely excluded sodium and showed no anatomical alterations. Salt exposure influenced cell wall composition involving increases in the lignin : carbohydrate ratio in both species. • In conclusion, hydraulic stress adaptation involves cell wall modifications reciprocal to tension wood formation that result in the formation of a novel type of reaction wood in upright stems named 'pressure wood'. Our data suggest that transcriptional co-regulation of a core set of genes determines reaction wood composition. © 2011 The Authors. New Phytologist © 2011 New Phytologist Trust.

Termite feeding preference to four wood species after gamma irradiation

International Nuclear Information System (INIS)

Katsumata, N.; Yoshimura, T.; Tsunoda, K.; Imamura, Y.

2007-01-01

The effect of gamma irradiation at 100 kGy and at lower levels on termite resistance was examined in the laboratory by no-choice and choice feeding termite tests (Coptotermes formosanus Shiraki) using four wood species: sapwood of Cryptomeria japonica D. Don, and heartwoods of Pseudotsuga menziesii (Mirbel) Franco, Larix kaempferi (Lambert) Carriere, and Chamaecyparis obtusa Endl. The wood consumption rates in C. japonica and P. menziesii specimens were likely to increase with increases in gamma-irradiation levels, whereas little effect of gamma irradiation was seen in L. kaempferi and C. obtusa. Similar results were obtained in the two-choice test. The current results indicated that in the two-choice test with C. formosanus, 100-kGy-irradiated C. japonica and P. menziesii, which are not rich in antitermite substances, were eaten more than other wood samples with or without gamma irradiation. However, only C. japonica showed significant difference in termite feeding activity. The mass loss in 100-kGy-irradiated C. japonica was significantly higher in the multichoice test

Evaluation of mechanical properties and durability performance of HDPE-wood composites

Energy Technology Data Exchange (ETDEWEB)

Tazi, M.; Erchiqui, F. [Engineering department, Université de Quebec en Abitibi-Témiscamingue (Canada); Kaddami, H. [Université Caddi Ayad Marrakech, Laboratoire ’LCO2MC’, B.P. 549, Marrakech 40000, Maroc (Morocco); Bouazara, M. [Mechanical department, Université de Québec à Chicoutimi Canada (Canada); Poaty, B. [Technology Center of industrial residuals, QC Canada (Canada)

2015-05-22

The objective of this work is to evaluate the mechanical properties and durability performance of bio-composite materials made from sawdust and thermoplastic polymer (HDPE). For the preparation of the composites, sawdust in different proportions with Maleic Anhydride grafted Polyethylene (MAPE) as the coupling agent was used. The thermal and mechanical properties were successively characterized. The results indicate that adding wood fillers to a polymer matrix increases the degree of crystallinity and improves the tensile strength and ductility of composites. On the contrary, resistance to water absorption decreases as a function of the wood fillers. Scanning electron microscopy (SEM) was used to analyze morphological structure alteration when exposed to intense weathering. The biodegradability of bio-composites up to 97 days was also investigated; the results indicate that, by increasing the filler content, the amount of weight loss increased as well. In other words, even though the addition of sawdust to thermoplastic polymer improves the mechanical performance of a composite material, it also accelerates the biodegradation rate of the composite. An optimum amount of filler content might compromise the effect of biodegradation and mechanical properties of composite materials.

Evaluation of mechanical properties and durability performance of HDPE-wood composites

International Nuclear Information System (INIS)

Tazi, M.; Erchiqui, F.; Kaddami, H.; Bouazara, M.; Poaty, B.

2015-01-01

The objective of this work is to evaluate the mechanical properties and durability performance of bio-composite materials made from sawdust and thermoplastic polymer (HDPE). For the preparation of the composites, sawdust in different proportions with Maleic Anhydride grafted Polyethylene (MAPE) as the coupling agent was used. The thermal and mechanical properties were successively characterized. The results indicate that adding wood fillers to a polymer matrix increases the degree of crystallinity and improves the tensile strength and ductility of composites. On the contrary, resistance to water absorption decreases as a function of the wood fillers. Scanning electron microscopy (SEM) was used to analyze morphological structure alteration when exposed to intense weathering. The biodegradability of bio-composites up to 97 days was also investigated; the results indicate that, by increasing the filler content, the amount of weight loss increased as well. In other words, even though the addition of sawdust to thermoplastic polymer improves the mechanical performance of a composite material, it also accelerates the biodegradation rate of the composite. An optimum amount of filler content might compromise the effect of biodegradation and mechanical properties of composite materials

Factors affecting wood energy consumption by U.S. households

Science.gov (United States)

Nianfu Song; Francisco X. Aguilar; Stephen R. Shifley; Michael E. Goerndt

2012-01-01

About 23% of energy derived from woody sources in the U.S. was consumed by households, of which 70% was used by households in rural areas in 2005. We investigated factors affecting household-level wood energy consumption in the four continental U.S. regions using data from the U.S. Residential Energy Consumption Survey. To account for a large number of zero...

Nutritional ecology of the Formosan subterranean termite (Isoptera: Rhinotermitidae): growth and survival of incipient colonies feeding on preferred wood species.

Science.gov (United States)

Morales-Ramos, Juan A; Rojas, M Guadalupe

2003-02-01

The wood of 11 plant species was evaluated as a food source significantly impacting the growth and survival of incipient colonies of the Formosan subterranean termite, Coptotermes formosanus Shiraki (Isoptera: Rhinotermitidae). Colonies of C. formosanus feeding on pecan, Carya illinoensis (Wangenh.), and red gum, Liquidambar styraciflua L., produced significantly more progeny than colonies feeding on other wood species tested. Progeny of colonies feeding on pecan and American ash, Fraxinus americana L., had significantly greater survival than progeny of colonies feeding on other wood species. Colonies feeding on a nutritionally supplemented cellulose based matrix showed similar fitness characteristics as colonies feeding on the best wood treatments. These results indicate that differences observed in colony fitness can be partially explained by nutritional value of the food treatment, raising the possibility that wood from different tree species have different nutritional values to the Formosan subterranean termites. Colonies feeding on loblolly pine, Pinus taeda L., and ponderosa pine, Pinus ponderosa Laws., had significantly lower survival and produced significantly fewer workers and soldiers than colonies feeding on other wood species. Colony survival from 90 to 180 d of age and from 90 to 360 d of age was significantly correlated with the number of workers present at 90 d of colony age, indicating that colony survival depends on the presence of workers. Wood consumption in a multiple-choice study was significantly correlated with colony fitness value. This suggests that feeding preference of C. formosanus is at least partially influenced by the nutritional value of the food source.

Significance of wood extractives for wood bonding.

Science.gov (United States)

Roffael, Edmone

2016-02-01

Wood contains primary extractives, which are present in all woods, and secondary extractives, which are confined in certain wood species. Extractives in wood play a major role in wood-bonding processes, as they can contribute to or determine the bonding relevant properties of wood such as acidity and wettability. Therefore, extractives play an immanent role in bonding of wood chips and wood fibres with common synthetic adhesives such as urea-formaldehyde-resins (UF-resins) and phenol-formaldehyde-resins (PF-resins). Extractives of high acidity accelerate the curing of acid curing UF-resins and decelerate bonding with alkaline hardening PF-resins. Water-soluble extractives like free sugars are detrimental for bonding of wood with cement. Polyphenolic extractives (tannins) can be used as a binder in the wood-based industry. Additionally, extractives in wood can react with formaldehyde and reduce the formaldehyde emission of wood-based panels. Moreover, some wood extractives are volatile organic compounds (VOC) and insofar also relevant to the emission of VOC from wood and wood-based panels.

Framework for modelling economic impacts of invasive species, applied to pine wood nematode in Europe.

Directory of Open Access Journals (Sweden)

Tarek Soliman

Full Text Available BACKGROUND: Economic impact assessment of invasive species requires integration of information on pest entry, establishment and spread, valuation of assets at risk and market consequences at large spatial scales. Here we develop such a framework and demonstrate its application to the pinewood nematode, Bursaphelenchus xylophilus, which threatens the European forestry industry. The effect of spatial resolution on the assessment result is analysed. METHODOLOGY/PRINCIPAL FINDINGS: Direct economic impacts resulting from wood loss are computed using partial budgeting at regional scale, while impacts on social welfare are computed by a partial equilibrium analysis of the round wood market at EU scale. Substantial impacts in terms of infested stock are expected in Portugal, Spain, Southern France, and North West Italy but not elsewhere in EU in the near future. The cumulative value of lost forestry stock over a period of 22 years (2008-2030, assuming no regulatory control measures, is estimated at €22 billion. The greatest yearly loss of stock is expected to occur in the period 2014-2019, with a peak of three billion euros in 2016, but stabilizing afterwards at 300-800 million euros/year. The reduction in social welfare follows the loss of stock with considerable delay because the yearly harvest from the forest is only 1.8%. The reduction in social welfare for the downstream round wood market is estimated at €218 million in 2030, whereby consumers incur a welfare loss of €357 million, while producers experience a €139 million increase, due to higher wood prices. The societal impact is expected to extend to well beyond the time horizon of the analysis, and long after the invasion has stopped. CONCLUSIONS/SIGNIFICANCE: Pinewood nematode has large economic consequences for the conifer forestry industry in the EU. A change in spatial resolution affected the calculated directed losses by 24%, but did not critically affect conclusions.

Radial variation in fiber length of some lesser used wood species in ...

African Journals Online (AJOL)

computer

2012-09-20

Sep 20, 2012 ... Variations in fibre length of ten lesser used wood species were investigated. The mean fibre length ..... the growth of coniferous trees. Can. J. Bot.45: 1359-1369 ... morphology and paper properties: a review of literature. Tappi ...

Downregulation of RWA genes in hybrid aspen affects xylan acetylation and wood saccharification.

Science.gov (United States)

Pawar, Prashant Mohan-Anupama; Ratke, Christine; Balasubramanian, Vimal K; Chong, Sun-Li; Gandla, Madhavi Latha; Adriasola, Mathilda; Sparrman, Tobias; Hedenström, Mattias; Szwaj, Klaudia; Derba-Maceluch, Marta; Gaertner, Cyril; Mouille, Gregory; Ezcurra, Ines; Tenkanen, Maija; Jönsson, Leif J; Mellerowicz, Ewa J

2017-06-01

High acetylation of angiosperm wood hinders its conversion to sugars by glycoside hydrolases, subsequent ethanol fermentation and (hence) its use for biofuel production. We studied the REDUCED WALL ACETYLATION (RWA) gene family of the hardwood model Populus to evaluate its potential for improving saccharification. The family has two clades, AB and CD, containing two genes each. All four genes are expressed in developing wood but only RWA-A and -B are activated by master switches of the secondary cell wall PtNST1 and PtMYB21. Histochemical analysis of promoter::GUS lines in hybrid aspen (Populus tremula × tremuloides) showed activation of RWA-A and -B promoters in the secondary wall formation zone, while RWA-C and -D promoter activity was diffuse. Ectopic downregulation of either clade reduced wood xylan and xyloglucan acetylation. Suppressing both clades simultaneously using the wood-specific promoter reduced wood acetylation by 25% and decreased acetylation at position 2 of Xylp in the dimethyl sulfoxide-extracted xylan. This did not affect plant growth but decreased xylose and increased glucose contents in the noncellulosic monosaccharide fraction, and increased glucose and xylose yields of wood enzymatic hydrolysis without pretreatment. Both RWA clades regulate wood xylan acetylation in aspen and are promising targets to improve wood saccharification. © 2017 The Authors. New Phytologist © 2017 New Phytologist Trust.

Species associations overwhelm abiotic conditions to dictate the structure and function of wood-decay fungal communities.

Science.gov (United States)

Maynard, Daniel S; Covey, Kristofer R; Crowther, Thomas W; Sokol, Noah W; Morrison, Eric W; Frey, Serita D; van Diepen, Linda T A; Bradford, Mark A

2018-04-01

Environmental conditions exert strong controls on the activity of saprotrophic microbes, yet abiotic factors often fail to adequately predict wood decomposition rates across broad spatial scales. Given that species interactions can have significant positive and negative effects on wood-decay fungal activity, one possibility is that biotic processes serve as the primary controls on community function, with abiotic controls emerging only after species associations are accounted for. Here we explore this hypothesis in a factorial field warming- and nitrogen-addition experiment by examining relationships among wood decomposition rates, fungal activity, and fungal community structure. We show that functional outcomes and community structure are largely unrelated to abiotic conditions, with microsite and plot-level abiotic variables explaining at most 19% of the total variability in decomposition and fungal activity, and 2% of the variability in richness and evenness. In contrast, taxonomic richness, evenness, and species associations (i.e., co-occurrence patterns) exhibited strong relationships with community function, accounting for 52% of the variation in decomposition rates and 73% in fungal activity. A greater proportion of positive vs. negative species associations in a community was linked to strong declines in decomposition rates and richness. Evenness emerged as a key mediator between richness and function, with highly even communities exhibiting a positive richness-function relationship and uneven communities exhibiting a negative or null response. These results suggest that community-assembly processes and species interactions are important controls on the function of wood-decay fungal communities, ultimately overwhelming substantial differences in abiotic conditions. © 2018 by the Ecological Society of America.

WOOD ANATOMY OF SEVEN SPECIES KNOWN AS “PAU-PARA-TUDO” IN BRAZIL

Directory of Open Access Journals (Sweden)

Claúdia Luizon Dias Leme

2016-09-01

Full Text Available Different medicinal plant species can be sold under the same common name. Considering the importance of the correct identification, this study aims to separate, using wood anatomy, seven species popularly known as pau-para-tudo. The results show that Drimys brasiliensis is separated from the others by the presence of tracheids. Capsicodendron dinisii hhas scalariform perforation plates and oil cells associated with the axial parenchyma. Axial parenchyma paratracheal vasicentric and in marginal bands beyond the rays’ width, can separate Osteophoeum platyspermum from Simaba cedron. Handroanthus serratifolius has the unique presence of the axial unilateral paratracheal parenchyma and storied cell elements (parenchyma, fibers and vessel elements. Rauvolfia sellowii and Leptolobium dasycarpum can be separated by the number of square/upright marginal ray cells, greater in Rauvolfia sellowii. Thus, this work shows that wood anatomy is a valuable tool for species separation, helps with the identification and consequently is important for the quality control of plant product.

Effects of mechanical properties of thermoplastic materials on the initial force of thermoplastic appliances.

Science.gov (United States)

Kohda, Naohisa; Iijima, Masahiro; Muguruma, Takeshi; Brantley, William A; Ahluwalia, Karamdeep S; Mizoguchi, Itaru

2013-05-01

To measure the forces delivered by thermoplastic appliances made from three materials and investigate effects of mechanical properties, material thickness, and amount of activation on orthodontic forces. Three thermoplastic materials, Duran (Scheu Dental), Erkodur (Erkodent Erich Kopp GmbH), and Hardcast (Scheu Dental), with two different thicknesses were selected. Values of elastic modulus and hardness were obtained from nanoindentation measurements at 28°C. A custom-fabricated system with a force sensor was employed to obtain measurements of in vitro force delivered by the thermoplastic appliances for 0.5-mm and 1.0-mm activation for bodily tooth movement. Experimental results were subjected to several statistical analyses. Hardcast had significantly lower elastic modulus and hardness than Duran and Erkodur, whose properties were not significantly different. Appliances fabricated from thicker material (0.75 mm or 0.8 mm) always produced significantly greater force than those fabricated from thinner material (0.4 mm or 0.5 mm). Appliances with 1.0-mm activation produced significantly lower force than those with 0.5-mm activation, except for 0.4-mm thick Hardcast appliances. A strong correlation was found between mechanical properties of the thermoplastic materials and force produced by the appliances. Orthodontic forces delivered by thermoplastic appliances depend on the material, thickness, and amount of activation. Mechanical properties of the polymers obtained by nanoindentation testing are predictive of force delivery by these appliances.

New Insights on Wood Dimensional Stability Influenced by Secondary Metabolites: The Case of a Fast-Growing Tropical Species Bagassa guianensis Aubl.

Directory of Open Access Journals (Sweden)

Julie Bossu

Full Text Available Challenging evaluation of tropical forest biodiversity requires the reporting of taxonomic diversity but also the systematic characterization of wood properties in order to discover new promising species for timber industry. Among wood properties, the dimensional stability is regarded as a major technological characteristic to validate whether a wood species is adapted to commercial uses. Cell structure and organization are known to influence the drying shrinkage making wood density and microfibrils angle markers of choice to predict wood dimensional stability. On the contrary the role of wood extractive content remains unclear. This work focuses on the fast-growing tropical species Bagassa guianensis and we report herein a correlation between heartwood drying shrinkage and extractive content. Chemical extractions and shrinkage experiments were performed on separate wood twin samples to better evaluate correctly how secondary metabolites influence the wood shrinkage behaviour. Extractive content were qualitatively and quantitatively analysed using HPLC and NMR spectroscopy. We found that B guianensis heartwood has a homogeneous low shrinkage along its radius that could not be explained only by its basic density. In fact the low drying shrinkage is correlated to the high extractive content and a corrected model to improve the prediction of wood dimensional stability is presented. Additionally NMR experiments conducted on sapwood and heartwood extracts demonstrate that secondary metabolites biosynthesis occurs in sapwood thus revealing B. guianensis as a Juglans-Type heartwood formation. This work demonstrates that B. guianensis, a fast-growing species associated with high durability and high dimensional stability, is a good candidate for lumber production and commercial purposes.

Insights into intraspecific wood density variation and its relationship to growth, height and elevation in a treeline species.

Science.gov (United States)

Fajardo, A

2018-05-01

The wood economics spectrum provides a general framework for interspecific trait-trait coordination across wide environmental gradients. Whether global patterns are mirrored within species constitutes a poorly explored subject. In this study, I first determined whether wood density co-varies together with elevation, tree growth and height at the within-species level. Second, I determined the variation of wood density in different stem parts (trunk, branch and twigs). In situ trunk sapwood, trunk heartwood, branch and twig densities, in addition to stem growth rates and tree height were determined in adult trees of Nothofagus pumilio at four elevations in five locations spanning 18° of latitude. Mixed effects models were fitted to test relationships among variables. The variation in wood density reported in this study was narrow (ca. 0.4-0.6 g cm -3 ) relative to global density variation (ca. 0.3-1.0 g cm -3 ). There was no significant relationship between stem growth rates and wood density. Furthermore, the elevation gradient did not alter the wood density of any stem part. Trunk sapwood density was negatively related to tree height. Twig density was higher than branch and trunk densities. Trunk heartwood density was always significantly higher than sapwood density. Negative across-species trends found in the growth-wood density relationship may not emerge as the aggregate of parallel intraspecific patterns. Actually, trees with contrasting growth rates show similar wood density values. Tree height, which is tightly related to elevation, showed a negative relationship with sapwood density. © 2018 German Society for Plant Sciences and The Royal Botanical Society of the Netherlands.

1H Nuclear Magnetic Resonance of Lodgepole Pine Wood Chips Affected by the Mountain Pine Beetle

Directory of Open Access Journals (Sweden)

Hartwig Peemoeller

2010-12-01

Full Text Available In this study, wood-water interactions of mountain pine beetle affected lodgepole pine were found to vary with time since death. Based on an analysis of magnetization components and spin-spin relaxation times from 1H NMR, it was determined that the mountain pine beetle attack does not affect the crystalline structure of the wood. Both the amorphous structure and the water components vary with time since death, which could be due to the fungi present after a mountain pine beetle attack, as well as the fact that wood from the grey-stage of attack cycles seasonally through adsorption and desorption in the stand.

¹H Nuclear Magnetic Resonance of Lodgepole Pine Wood Chips Affected by the Mountain Pine Beetle.

Science.gov (United States)

Todoruk, Tara M; Hartley, Ian D; Teymoori, Roshanak; Liang, Jianzhen; Peemoeller, Hartwig

2010-12-31

In this study, wood-water interactions of mountain pine beetle affected lodgepole pine were found to vary with time since death. Based on an analysis of magnetization components and spin-spin relaxation times from 1H NMR, it was determined that the mountain pine beetle attack does not affect the crystalline structure of the wood. Both the amorphous structure and the water components vary with time since death, which could be due to the fungi present after a mountain pine beetle attack, as well as the fact that wood from the grey-stage of attack cycles seasonally through adsorption and desorption in the stand.

Effect of cement/wood ratios and wood storage conditions on hydration temperature, hydration time, and compressive strength of wood-cement mixtures

Science.gov (United States)

Andy W.C. Lee; Zhongli Hong; Douglas R. Phillips; Chung-Yun Hse

1987-01-01

This study investigated the effect of cement/wood ratios and wood storage conditions on hydration temperature, hydration time, and compressive strength of wood-cement mixtures made from six wood species: southern pine, white oak, southern red oak, yellow-poplar, sweetgum, and hickory. Cement/wood ratios varied from 13/1 to 4/1. Wood storage conditions consisted of air-...

Wood decomposition as influenced by invertebrates.

Science.gov (United States)

Ulyshen, Michael D

2016-02-01

The diversity and habitat requirements of invertebrates associated with dead wood have been the subjects of hundreds of studies in recent years but we still know very little about the ecological or economic importance of these organisms. The purpose of this review is to examine whether, how and to what extent invertebrates affect wood decomposition in terrestrial ecosystems. Three broad conclusions can be reached from the available literature. First, wood decomposition is largely driven by microbial activity but invertebrates also play a significant role in both temperate and tropical environments. Primary mechanisms include enzymatic digestion (involving both endogenous enzymes and those produced by endo- and ectosymbionts), substrate alteration (tunnelling and fragmentation), biotic interactions and nitrogen fertilization (i.e. promoting nitrogen fixation by endosymbiotic and free-living bacteria). Second, the effects of individual invertebrate taxa or functional groups can be accelerative or inhibitory but the cumulative effect of the entire community is generally to accelerate wood decomposition, at least during the early stages of the process (most studies are limited to the first 2-3 years). Although methodological differences and design limitations preclude meta-analysis, studies aimed at quantifying the contributions of invertebrates to wood decomposition commonly attribute 10-20% of wood loss to these organisms. Finally, some taxa appear to be particularly influential with respect to promoting wood decomposition. These include large wood-boring beetles (Coleoptera) and termites (Termitoidae), especially fungus-farming macrotermitines. The presence or absence of these species may be more consequential than species richness and the influence of invertebrates is likely to vary biogeographically. Published 2014. This article is a U.S. Government work and is in the public domain in the USA.

Cryomilling of Thermoplastic Powder for Prepreg Applications

Science.gov (United States)

2013-09-01

Cryomilling of Thermoplastic Powder for Prepreg Applications by Brian Parquette, Anit Giri, Daniel J. O’Brien, Sarah Brennan, Kyu Cho, and...MD 21005-5066 ARL-TR-6591 September 2013 Cryomilling of Thermoplastic Powder for Prepreg Applications Brian Parquette and Sarah Brennan...COVERED (From - To) 1 March 2012–30 May 2013 4. TITLE AND SUBTITLE Cryomilling of Thermoplastic Powder for Prepreg Applications 5a. CONTRACT

Multiple-objective optimization in precision laser cutting of different thermoplastics

Science.gov (United States)

Tamrin, K. F.; Nukman, Y.; Choudhury, I. A.; Shirley, S.

2015-04-01

Thermoplastics are increasingly being used in biomedical, automotive and electronics industries due to their excellent physical and chemical properties. Due to the localized and non-contact process, use of lasers for cutting could result in precise cut with small heat-affected zone (HAZ). Precision laser cutting involving various materials is important in high-volume manufacturing processes to minimize operational cost, error reduction and improve product quality. This study uses grey relational analysis to determine a single optimized set of cutting parameters for three different thermoplastics. The set of the optimized processing parameters is determined based on the highest relational grade and was found at low laser power (200 W), high cutting speed (0.4 m/min) and low compressed air pressure (2.5 bar). The result matches with the objective set in the present study. Analysis of variance (ANOVA) is then carried out to ascertain the relative influence of process parameters on the cutting characteristics. It was found that the laser power has dominant effect on HAZ for all thermoplastics.

Inside the guts of wood-eating catfishes: can they digest wood?

Science.gov (United States)

German, Donovan P

2009-11-01

To better understand the structure and function of the gastrointestinal (GI) tracts of wood-eating catfishes, the gross morphology, length, and microvilli surface area (MVSA) of the intestines of wild-caught Panaque nocturnus, P. cf. nigrolineatus "Marañon", and Hypostomus pyrineusi were measured, and contrasted against these same metrics of a closely related detritivore, Pterygoplichthys disjunctivus. All four species had anatomically unspecialized intestines with no kinks, valves, or ceca of any kind. The wood-eating catfishes had body size-corrected intestinal lengths that were 35% shorter than the detritivore. The MVSA of all four species decreased distally in the intestine, indicating that nutrient absorption preferentially takes place in the proximal and mid-intestine, consistent with digestive enzyme activity and luminal carbohydrate profiles for these same species. Wild-caught Pt. disjunctivus, and P. nigrolineatus obtained via the aquarium trade, poorly digested wood cellulose (<33% digestibility) in laboratory feeding trials, lost weight when consuming wood, and passed stained wood through their digestive tracts in less than 4 h. Furthermore, no selective retention of small particles was observed in either species in any region of the gut. Collectively, these results corroborate digestive enzyme activity profiles and gastrointestinal fermentation levels in the fishes' GI tracts, suggesting that the wood-eating catfishes are not true xylivores such as beavers and termites, but rather, are detritivores like so many other fishes from the family Loricariidae.

Variation in foliar respiration and wood CO2 efflux rates among species and canopy layers in a wet tropical forest.

Science.gov (United States)

Asao, Shinichi; Bedoya-Arrieta, Ricardo; Ryan, Michael G

2015-02-01

As tropical forests respond to environmental change, autotrophic respiration may consume a greater proportion of carbon fixed in photosynthesis at the expense of growth, potentially turning the forests into a carbon source. Predicting such a response requires that we measure and place autotrophic respiration in a complete carbon budget, but extrapolating measurements of autotrophic respiration from chambers to ecosystem remains a challenge. High plant species diversity and complex canopy structure may cause respiration rates to vary and measurements that do not account for this complexity may introduce bias in extrapolation more detrimental than uncertainty. Using experimental plantations of four native tree species with two canopy layers, we examined whether species and canopy layers vary in foliar respiration and wood CO2 efflux and whether the variation relates to commonly used scalars of mass, nitrogen (N), photosynthetic capacity and wood size. Foliar respiration rate varied threefold between canopy layers, ∼0.74 μmol m(-2) s(-1) in the overstory and ∼0.25 μmol m(-2) s(-1) in the understory, but little among species. Leaf mass per area, N and photosynthetic capacity explained some of the variation, but height explained more. Chamber measurements of foliar respiration thus can be extrapolated to the canopy with rates and leaf area specific to each canopy layer or height class. If area-based rates are sampled across canopy layers, the area-based rate may be regressed against leaf mass per area to derive the slope (per mass rate) to extrapolate to the canopy using the total leaf mass. Wood CO2 efflux varied 1.0-1.6 μmol m(-2) s(-1) for overstory trees and 0.6-0.9 μmol m(-2) s(-1) for understory species. The variation in wood CO2 efflux rate was mostly related to wood size, and little to species, canopy layer or height. Mean wood CO2 efflux rate per surface area, derived by regressing CO2 efflux per mass against the ratio of surface

Transferability of microsatellite markers located in candidate genes for wood properties between Eucalyptus species

Directory of Open Access Journals (Sweden)

Cintia V. Acuña

2014-12-01

Full Text Available Aim of study:  To analyze the feasibility of extrapolating conclusions on wood quality genetic control between different Eucalyptus species, particularly from species with better genomic information, to those less characterized. For this purpose, the first step is to analyze the conservation and cross-transferability of microsatellites markers (SSRs located in candidate genes.Area of study: Eucalyptus species implanted in Argentina coming from different Australian origins.Materials and methods: Twelve validated and polymorphic SSRs in candidate genes (SSR-CGs for wood quality in E. globulus were selected for cross species amplification in six species: E. grandis, E. saligna, E. dunnii, E. viminalis, E. camaldulensis and E. tereticornis.Main results: High cross-species transferability (92% to 100% was found for the 12 polymorphic SSRs detected in E. globulus. These markers revealed allelic diversity in nine important candidate genes: cinnamoyl CoA reductase (CCR, cellulose synthase 3 (CesA3, the transcription factor LIM1, homocysteine S-methyltransferase (HMT, shikimate kinase (SK, xyloglucan endotransglycosylase 2 (XTH2, glutathione S-transferase (GST, glutamate decarboxylase (GAD and peroxidase (PER.Research highlights: The markers described are potentially suitable for comparative QTL mapping, molecular marker assisted breeding (MAB and for population genetic studies across different species within the subgenus Symphyomyrtus.Keywords: validation; cross-transferability; SSR; functional markers; eucalypts; Symphyomyrtus.

DURABILTY OF 25 LOCAL SPECIFIC WOOD SPECIES FROM JAVA PRESERVED WITH CCB AGAINST MARINE BORERS ATTACK

Directory of Open Access Journals (Sweden)

Mohammad Muslich

2010-12-01

Full Text Available This study was conducted to provide basis information of the 25 local specific wood species indigenous from Java treated by copper bichromated boron (CCB. The full-cell process for 2 hours and 150 psi during the pressure-keeping period was employed. The IUFRO method was applied for the determination of wood treatability class. The treated and untreated wood specimens were tied together using plastic cord, arranged into a raft like assembly, and then exposed for 3, 6, and 12 months to the brackish water situated at Rambut Island’s coastal area. The Nordic Wood Preservation Council (NWPC standard No.1.4.2.2/75 was used to determine the intensity of marine borer infestation. The results revealed that 19 out of those 25 species were classified as easy to be preser ved, four species as moderate, and the remaining two were difficult to be preser ved. Those 19 species, i.e. Tamarindus indica L., Diplodiscus sp., Ficus variegate R .Br., Ehretia acuminata R .Br., Meliocope lunu-ankenda (Gaertn T.G. Hartley, Colona javanica B.L., Pouteria duclitanBachni., Stercularia oblongata R .Br., Ficus vasculosa Wall ex Miq., Callophyllum grandiflorum JJS., Turpinia sphaerocarpa Hassk., Neolitsea triplinervia Merr., Acer niveum Bl., Sloanea sigun Szysz., Castanopsis acuminatissima A.DC., Cinnamomum iners Reinw. Ex Blume., Litsea angulata Bl., Ficus nervosa Heyne., and Horsfieldia glabra Warb. were more permeable implying that the CCB retention and penetration were greater and deeper. Hymeneaecarboril.L., LitseaodoriferaVal., Gironniera subasqualisPlanch., and LinderapolyanthaBoerl. were moderately permeable. Castanopsis tunggurut A.DC. and Azadirachta indica Juss. were the least permeable judging that the CCB retention and penetration were lowest and shallowest. The treated wood specimens in this regard were able to prevent marine borers attack. Meanwhile, the untreated specimens were susceptible to marine borers attack, except Azadirachta indica. The attacking

Response surface methodology to simplify calculation of wood energy potency from tropical short rotation coppice species

Science.gov (United States)

Haqiqi, M. T.; Yuliansyah; Suwinarti, W.; Amirta, R.

2018-04-01

Short Rotation Coppice (SRC) system is an option to provide renewable and sustainable feedstock in generating electricity for rural area. Here in this study, we focussed on application of Response Surface Methodology (RSM) to simplify calculation protocols to point out wood chip production and energy potency from some tropical SRC species identified as Bauhinia purpurea, Bridelia tomentosa, Calliandra calothyrsus, Fagraea racemosa, Gliricidia sepium, Melastoma malabathricum, Piper aduncum, Vernonia amygdalina, Vernonia arborea and Vitex pinnata. The result showed that the highest calorific value was obtained from V. pinnata wood (19.97 MJ kg-1) due to its high lignin content (29.84 %, w/w). Our findings also indicated that the use of RSM for estimating energy-electricity of SRC wood had significant term regarding to the quadratic model (R2 = 0.953), whereas the solid-chip ratio prediction was accurate (R2 = 1.000). In the near future, the simple formula will be promising to calculate energy production easily from woody biomass, especially from SRC species.

1H Nuclear Magnetic Resonance of Lodgepole Pine Wood Chips Affected by the Mountain Pine Beetle

OpenAIRE

Todoruk, Tara M.; Hartley, Ian D.; Teymoori, Roshanak; Liang, Jianzhen; Peemoeller, Hartwig

2010-01-01

In this study, wood-water interactions of mountain pine beetle affected lodgepole pine were found to vary with time since death. Based on an analysis of magnetization components and spin-spin relaxation times from 1H NMR, it was determined that the mountain pine beetle attack does not affect the crystalline structure of the wood. Both the amorphous structure and the water components vary with time since death, which could be due to the fungi present after a mountain pine beetle attack, as wel...

Final Report: Development of Renewable Microbial Polyesters for Cost Effective and Energy-Efficient Wood-Plastic Composites

Energy Technology Data Exchange (ETDEWEB)

David N. Thompson, Robert W. Emerick, Alfred B. England, James P. Flanders, Frank J. Loge, Katherine A. Wiedeman, Michael P. Wolcott

2010-04-08

The forestry, wood and paper industries in the United States provide thousands of productive well-paying jobs; however, in the face of the recent economic downturn it faces significant challenges in remaining economically viable and competitive. To compete successfully on a global market that is increasingly driven by the need for sustainable products and practices, the industry must improve margins and diversify product lines while continuing to produce the staple products. One approach that can help to accomplish this goal sustainably is the forest biorefinery. In the forest biorefinery, traditional waste streams are utilized singly or in combination to manufacture additional products in a profitable and environmentally sustainable manner. In this project, we proposed to produce wood fiber reinforced thermoplastic composites (WFRTCs) using microbial thermoplastic polyesters in place of petroleum-derived plastic. WFRTCs are a rapidly growing product area, averaging a 38% growth rate since 1997. Their production is dependent on substantial quantities of petroleum based thermoplastics, increasing their overall energy costs by over 230% when compared to traditional Engineered Wood Products (EWP). Utilizing bio-based thermoplastics for these materials can reduce our dependence on foreign petroleum. Renewable microbial polyesters are not currently used in WFRTCs primarily because their production costs are several times higher than those of conventional petrochemical-derived plastics, limiting their use to small specialty markets. The strategy for this project was to economically produce WFRTCs using microbial polyesters by reducing or eliminating the most costly steps in the bio-plastic production. This would be achieved by producing them in and from waste effluents from the municipal and forest products sectors, and by eliminating the costly purification steps. After production the plasticladen biosolids would be dried and used directly to replace petroleum

Wood for sound.

Science.gov (United States)

Wegst, Ulrike G K

2006-10-01

The unique mechanical and acoustical properties of wood and its aesthetic appeal still make it the material of choice for musical instruments and the interior of concert halls. Worldwide, several hundred wood species are available for making wind, string, or percussion instruments. Over generations, first by trial and error and more recently by scientific approach, the most appropriate species were found for each instrument and application. Using material property charts on which acoustic properties such as the speed of sound, the characteristic impedance, the sound radiation coefficient, and the loss coefficient are plotted against one another for woods. We analyze and explain why spruce is the preferred choice for soundboards, why tropical species are favored for xylophone bars and woodwind instruments, why violinists still prefer pernambuco over other species as a bow material, and why hornbeam and birch are used in piano actions.

Wood preservative testing

Science.gov (United States)

Rebecca Ibach; Stan T. Lebow

2012-01-01

Most wood species used in commercial and residential construction have little natural biological durability and will suffer from biodeterioration when exposed to moisture. Historically, this problem has been overcome by treating wood for outdoor use with toxic wood preservatives. As societal acceptance of chemical use changes, there is continual pressure to develop and...

Wood plastic combination

International Nuclear Information System (INIS)

Cunanan, S.A.; Bonoan, L.S.; Verceluz, F.P.; Azucena, E.A.

1976-03-01

The purpose of this study is to improve the physical and mechaniproperties of local inferior quality wood species by radiation-induced graft polymerization with plastic monomers. The process involves the following: 1) Preparation of sample; 2) Impregnation of sample with the monomers; 3) Irradiation of the impregnated sample with the use of 20,000 curie Co-60 as gamma-source; 4) Drying of irradiated sample to remove the unpolymerized monomer. Experimentation on different wood species were undertaken and the results given. From the results obtained, it can be concluded that the monomers systems MMA, MMA-USP, and styrene-USP are suitable for graft polymerization with the wood species almon, apitong, bagtikan, mayapis, red lauan, and tanguile. This is shown by their maximum conversion value which range from 86% to 96% with the optimum dose range of 1 to 2 Mrads. However, in the application of WPC process, properties that are required in a given wood product must be considered, thus aid in the selection of the monomer system to be used with a particular wood species. Some promising applications of WPC is in the manufacture of picker sticks, shuttles, and bobbins for the textile industry. However, there is a need for a pilot plant scale study so that an economic assessment of the commercial feasibility of this process can be made

Lumber attributes, characteristics, and species preferences as indicated by secondary wood products firms in the continental United States.

Science.gov (United States)

David L. Nicholls; Joseph. Roos

2006-01-01

The purpose of this research was to evaluate selected lumber attributes, species preferences, and lumber use properties among secondary wood manufacturers in the United States. Our sample included producers of kitchen cabinets, furniture, doors, windows, and molded products who attended regional and national wood manufacturing events. More than 51% of respondents had...

Thermal load histories for North American roof assembles using various cladding materials including wood-thermoplastic composite shingles

Science.gov (United States)

J. E. Winandy

2006-01-01

Since 1991, thermal load histories for various roof cladding types have been monitored in outdoor attic structures that simulate classic North American light-framed construction. In this paper, the 2005 thermal loads for wood-based composite roof sheathing, wood rafters, and attics under wood-plastic composite shingles are compared to common North American roof...

Simulated long-term effects of varying tree retention on wood production, dead wood and carbon stock changes.

Science.gov (United States)

Santaniello, Francesca; Djupström, Line B; Ranius, Thomas; Weslien, Jan; Rudolphi, Jörgen; Sonesson, Johan

2017-10-01

Boreal forests are an important source of timber and pulp wood, but provide also other products and services. Utilizing a simulation program and field data from a tree retention experiment in a Scots pine forest in central Sweden, we simulated the consequences during the following 100 years of various levels of retention on production of merchantable wood, dead wood input (as a proxy for biodiversity), and carbon stock changes. At the stand level, wood production decreased with increased retention levels, while dead wood input and carbon stock increased. We also compared 12 scenarios representing a land sharing/land sparing gradient. In each scenario, a constant volume of wood was harvested with a specific level of retention in a 100-ha landscape. The area not needed to reach the defined volume was set-aside during a 100-year rotation period, leading to decreasing area of set-asides with increasing level of retention across the 12 scenarios. Dead wood input was positively affected by the level of tree retention whereas the average carbon stock decreased slightly with increasing level of tree retention. The scenarios will probably vary in how they favor species preferring different substrates. Therefore, we conclude that a larger variation of landscape-level conservation strategies, also including active creation of dead wood, may be an attractive complement to the existing management. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effects of Wood Ash on Soil Fungi

DEFF Research Database (Denmark)

Cruz Paredes, Carla

), copper (Cu) and nickel (Ni), is a major environmental concern. This work is part of the project ASHBACK (www.ashback.dk) which addresses the potentials and possible problems in re-distributing wood ash to the forest. The aim of this thesis was to determine the effects of biomass ash application...... in a Norway spruce forest where different amounts of wood ash were spread on the soil to study the effects on ectomycorrhizal (ECM) fungi, bioaccumulation of metals in sporocarps, and microbial communities. Laboratory microcosm experiments were run in parallel to the field studies, to compare the effects...... of wood ash with factorial additions of lime and Cd to disentangle the pH and Cd effects of wood ash amendments using community trait distributions. Barley yield, P content, and Cd content were not affected by biomass ashes. Some arbuscular mycorrhizal (AM) fungal species were reduced when biomass ashes...

Impact of thermoplastic mask on X-ray surface dose calculated with Monte Carlo code

International Nuclear Information System (INIS)

Zhao Yanqun; Li Jie; Wu Liping; Wang Pei; Lang Jinyi; Wu Dake; Xiao Mingyong

2010-01-01

Objective: To calculate the effects of thermoplastic mask on X-ray surface dose. Methods: The BEAMnrc Monte Carlo Code system, designed especially for computer simulation of radioactive sources, was performed to evaluate the effects of thermoplastic mask on X-ray surface dose.Thermoplastic mask came from our center with a material density of 1.12 g/cm 2 . The masks without holes, with holes size of 0.1 cm x 0.1 cm, and with holes size of 0. 1 cm x 0.2 cm, and masks with different depth (0.12 cm and 0.24 cm) were evaluated separately. For those with holes, the material width between adjacent holes was 0.1 cm. Virtual masks with a material density of 1.38 g/cm 3 without holes with two different depths were also evaluated. Results: Thermoplastic mask affected X-rays surface dose. When using a thermoplastic mask with the depth of 0.24 cm without holes, the surface dose was 74. 9% and 57.0% for those with the density of 1.38 g/cm 3 and 1.12 g/cm 3 respectively. When focusing on the masks with the density of 1.12 g/cm 3 , the surface dose was 41.2% for those with 0.12 cm depth without holes; 57.0% for those with 0. 24 cm depth without holes; 44.5% for those with 0.24 cm depth with holes size of 0.1 cm x 0.2 cm;and 54.1% for those with 0.24 cm depths with holes size of 0.1 cm x 0.1 cm.Conclusions: Using thermoplastic mask during the radiation increases patient surface dose. The severity is relative to the hole size and the depth of thermoplastic mask. The surface dose change should be considered in radiation planning to avoid severe skin reaction. (authors)

Trichoderma species occurring on wood with decay symptoms in mountain forests in Central Europe: genetic and enzymatic characterization.

Science.gov (United States)

Błaszczyk, Lidia; Strakowska, Judyta; Chełkowski, Jerzy; Gąbka-Buszek, Agnieszka; Kaczmarek, Joanna

2016-08-01

The aim of this study was to explore the species diversity of Trichoderma obtained from samples of wood collected in the forests of the Gorce Mountains (location A), Karkonosze Mountains (location B) and Tatra Mountains (location C) in Central Europe and to examine the cellulolytic and xylanolytic activity of these species as an expression of their probable role in wood decay processes. The present study has led to the identification of the following species and species complex: Trichoderma atroviride P. Karst., Trichoderma citrinoviride Bissett, Trichoderma cremeum P. Chaverri & Samuels, Trichoderma gamsii Samuels & Druzhin., Trichoderma harzianum complex, Trichoderma koningii Oudem., Trichoderma koningiopsis Samuels, C. Suárez & H.C. Evans, Trichoderma longibrachiatum Rifai, Trichoderma longipile Bissett, Trichoderma sp. (Hypocrea parapilulifera B.S. Lu, Druzhin. & Samuels), Trichoderma viride Schumach. and Trichoderma viridescens complex. Among them, T. viride was observed as the most abundant species (53 % of all isolates) in all the investigated locations. The Shannon's biodiversity index (H), evenness (E), and the Simpson's biodiversity index (D) calculations for each location showed that the highest species diversity and evenness were recorded for location A-Gorce Mountains (H' = 1.71, E = 0.82, D = 0.79). The preliminary screening of 119 Trichoderma strains for cellulolytic and xylanolytic activity showed the real potential of all Trichoderma species originating from wood with decay symptoms to produce cellulases and xylanases-the key enzymes in plant cell wall degradation.

Increased heat resistance in mycelia from wood fungi prevalent in forests characterized by fire: a possible adaptation to forest fire.

Science.gov (United States)

Carlsson, Fredrik; Edman, Mattias; Holm, Svante; Eriksson, Anna-Maria; Jonsson, Bengt Gunnar

2012-10-01

Forest fires have been the major stand-replacing/modifying disturbance in boreal forests. To adapt to fire disturbance, different strategies have evolved. This study focuses on wood fungi, and a specific adaptation to forest fire: increased heat resistance in their mycelia. Fifteen species of wood fungi were selected and a priori sorted in two groups according to their prevalence in fire-affected environments. The fungi were cultivated on fresh wood and exposed to 100, 140, 180, 220 °C for 5, 10, 15, 20 and 25 min. under laboratory conditions. A clear difference was found among the two groups. Species prevalent in fire-affected habitats had a much higher survival rate over all combinations of time and temperature compared to species associated with other environments. Thus, the results indicate that fire adaptation in terms of increased heat resistance in mycelia occurs in some species of wood fungi. Such adaptation will influence the ecology and population dynamics of wood fungi, as well as having implications for best practices during restoration fires. Copyright © 2012 The British Mycological Society. Published by Elsevier Ltd. All rights reserved.

Crosslinking of thermoplastic composites using electron beam radiation

International Nuclear Information System (INIS)

Strong, A.B.; Black, S.R.; Bryce, G.R.; Olcott, D.D.

1991-01-01

The crosslinking of thermoset materials has been clearly demonstrated to improve many desirable physical and chemical properties for composite applications. While thermoplastic resins also offer many advantages for composite applications, they are not crosslinked and, therefore, may not meet the same property criteria as crosslinked thermosets. Electron beams have been used successfully for crosslinking non-reinforced thermoplastic materials. Electron beams have also been used for curing composite thermoset materials. This research utilizes electron beams to crosslink high performance thermoplastic composite materials (PEEK and PPS with glass and carbon fibers). The tensile strength and tensile modulus are compared under various crosslinking conditions. The method is found to have some advantages in potentially improving physical properties of thermoplastic composite materials

Differential uptake of gold nanoparticles by 2 species of tadpole, the wood frog (Lithobates sylvaticus) and the bullfrog (Lithobates catesbeianus).

Science.gov (United States)

Thompson, Lucas B; Carfagno, Gerardo L F; Andresen, Kurt; Sitton, Andrea J; Bury, Taylor; Lee, Laura L; Lerner, Kevin T; Fong, Peter P

2017-12-01

Engineered nanoparticles are aquatic contaminants of emerging concern that exert ecotoxicological effects on a wide variety of organisms. We exposed cetyltrimethylammonium bromide-capped spherical gold nanoparticles to wood frog and bullfrog tadpoles with conspecifics and in combination with the other species continuously for 21 d, then measured uptake and localization of gold. Wood frog tadpoles alone and in combination with bullfrog tadpoles took up significantly more gold than bullfrogs. Bullfrog tadpoles in combination with wood frogs took up significantly more gold than controls. The rank order of weight-normalized gold uptake was wood frogs in combination > wood frogs alone > bullfrogs in combination > bullfrogs alone > controls. In all gold-exposed groups of tadpoles, gold was concentrated in the anterior region compared with the posterior region of the body. The concentration of gold nanoparticles in the anterior region of wood frogs both alone and in combination with bullfrogs was significantly higher than the corresponding posterior regions. We also measured depuration time of gold in wood frogs. After 21 d in a solution of gold nanoparticles, tadpoles lost >83% of internalized gold when placed in gold-free water for 5 d. After 10 d in gold-free water, tadpoles lost 94% of their gold. After 15 d, gold concentrations were below the level of detection. Our finding of differential uptake between closely related species living in similar habitats with overlapping geographical distributions argues against generalizing toxicological effects of nanoparticles for a large group of organisms based on measurements in only one species. Environ Toxicol Chem 2017;36:3351-3358. © 2017 SETAC. © 2017 SETAC.

Filling behaviour of wood plastic composites

Science.gov (United States)

Duretek, I.; Lucyshyn, T.; Holzer, C.

2017-01-01

Wood plastic composites (WPC) are a young generation of composites with rapidly growing usage within the plastics industry. The advantages are the availability and low price of the wood particles, the possibility of partially substituting the polymer in the mixture and sustainable use of the earth’s resources. The current WPC products on the market are to a large extent limited to extruded products. Nowadays there is a great interest in the market for consumer products in more use of WPC as an alternative to pure thermoplastics in injection moulding processes. This work presents the results of numerical simulation and experimental visualisation of the mould filling process in injection moulding of WPC. The 3D injection moulding simulations were done with the commercial software package Autodesk® Moldflow® Insight 2016 (AMI). The mould filling experiments were conducted with a box-shaped test part. In contrast to unfilled polymers the WPC has reduced melt elasticity so that the fountain flow often does not develop. This results in irregular flow front shapes in the moulded part, especially at high filler content.

Enrichment with Wood Blocks Does Not Affect Toxicity Assessment in an Exploratory Toxicology Model Using Sprague–Dawley Rats

Science.gov (United States)

Ditewig, Amy C; Bratcher, Natalie A; Davila, Donna R; Dayton, Brian D; Ebert, Paige; Lesuisse, Philippe; Liguori, Michael J; Wetter, Jill M; Yang, Hyuna; Buck, Wayne R

2014-01-01

Environmental enrichment in rodents may improve animal well-being but can affect neurologic development, immune system function, and aging. We tested the hypothesis that wood block enrichment affects the interpretation of traditional and transcriptomic endpoints in an exploratory toxicology testing model using a well-characterized reference compound, cyclophosphamide. ANOVA was performed to distinguish effects of wood block enrichment separate from effects of 40 mg/kg cyclophosphamide treatment. Biologically relevant and statistically significant effects of wood block enrichment occurred only for body weight gain. ANOVA demonstrated the expected effects of cyclophosphamide on food consumption, spleen weight, and hematology. According to transcriptomic endpoints, cyclophosphamide induced fewer changes in gene expression in liver than in spleen. Splenic transcriptomic pathways affected by cyclophosphamide included: iron hemostasis; vascular tissue angiotensin system; hepatic stellate cell activation and fibrosis; complement activation; TGFβ-induced hypertrophy and fibrosis; monocytes, macrophages, and atherosclerosis; and platelet activation. Changes in these pathways due to cyclophosphamide treatment were consistent with bone marrow toxicity regardless of enrichment. In a second study, neither enrichment nor type of cage flooring altered body weight or food consumption over a 28-d period after the first week. In conclusion, wood block enrichment did not interfere with a typical exploratory toxicology study; the effects of ingested wood on drug level kinetics may require further consideration. PMID:24827566

Consolidation modelling for thermoplastic composites forming simulation

Science.gov (United States)

Xiong, H.; Rusanov, A.; Hamila, N.; Boisse, P.

2016-10-01

Pre-impregnated thermoplastic composites are widely used in the aerospace industry for their excellent mechanical properties, Thermoforming thermoplastic prepregs is a fast manufacturing process, the automotive industry has shown increasing interest in this manufacturing processes, in which the reconsolidation is an essential stage. The model of intimate contact is investigated as the consolidation model, compression experiments have been launched to identify the material parameters, several numerical tests show the influents of the temperature and pressure applied during processing. Finally, a new solid-shell prismatic element has been presented for the simulation of consolidation step in the thermoplastic composites forming process.

Communities of fungi in decomposed wood of oak and pine

Directory of Open Access Journals (Sweden)

Kwaśna Hanna

2016-09-01

Full Text Available The abundance and diversity of wood decomposing fungi were investigated by isolating and cultivating filamentous fungi from wood and by detection of fruit bodies of ascomycetous and basidiomycetous fungi. The objective was to study the impact of forest management on fungi in 100-year-old oak and 87-year-old Scots pine forests in Northern Poland. Fungi were found on coarse woody debris of decayed stumps and fallen logs, boughs and branches in each of the three (managed and unmanaged examined stands. In total, 226 species of Oomycota and fungi were recorded. Oak wood was colonized by one species of Oomycota and 141 species of fungi including Zygomycota (19 species, Ascomycota (103 species and Basidiomycota (19 species. Scots pine wood was also colonized by one species of Oomycota and 138 species of fungi including Zygomycota (19 species, Ascomycota (90 species and Basidiomycota (29 species. In the first, second and third stages of decomposition, the oak wood was colonized by 101, 89 and 56 species of fungi respectively and pine wood was colonized by 82, 103 and 47 species respectively. Eighty three of the observed species (37% occurred on both types of wood, while the other species displayed nutritional preferences. A decrease in the number of species with advancing decay indicates the necessity for a continuous supply of dead wood to the forest ecosystem.

Chemical composition and fuel wood characteristics of fast growing tree species in India

Science.gov (United States)

Chauhan, S. K.; Soni, R.

2012-04-01

India is one of the growing economy in the world and energy is a critical input to sustain the growth of development. Country aims at security and efficiency of energy. Though fossil fuel will continue to play a dominant role in energy scenario but country is committed to global environmental well being thus stressing on environment friendly technologies. Concerns of energy security in this changing climatic situation have led to increasing support for the development of new renewable source of energy. Government though is determined to facilitate bio-energy and many projects have been established but initial after-affects more specifically on the domestic fuelwood are evident. Even the biomass power generating units are facing biomass crisis and accordingly the prices are going up. The CDM projects are supporting the viability of these units resultantly the Indian basket has a large number of biomass projects (144 out of total 506 with 28 per cent CERs). The use for fuelwood as a primary source of energy for domestic purpose by the poor people (approx. 80 per cent) and establishment of bio-energy plants may lead to deforestation to a great extent and only solution to this dilemma is to shift the wood harvest from the natural forests to energy plantations. However, there is conspicuous lack of knowledge with regards to the fuelwood characteristics of fast growing tree species for their selection for energy plantations. The calorific value of the species is important criteria for selection for fuel but it is affected by the proportions of biochemical constituents present in them. The aim of the present work was to study the biomass production, calorific value and chemical composition of different short rotation tree species. The study was done from the perspective of using the fast growing tree species for energy production at short rotation and the study concluded that short rotation tree species like Gmelina arborea, Eucalyptus tereticornis, Pongamia pinnata

Occurrence patterns of dead wood and wood-dependent lichens in managed boreal forest landscapes

OpenAIRE

Svensson, Måns

2013-01-01

Dead wood is a key resource for biodiversity, on which thousands of forest organisms are dependent. Because of current forest management, there has been a large-scale change in dead wood amounts and qualities, and consequently, many wood-dependent species are threatened. The general aim of this thesis is to increase our understanding of habitat requirements and occurrence patterns of wood-dependent lichens in managed, boreal forest landscapes. We surveyed dead wood and wood-dependent lichens ...

Detection of wood failure by image processing method: influence of algorithm, adhesive and wood species

Science.gov (United States)

Lanying Lin; Sheng He; Feng Fu; Xiping Wang

2015-01-01

Wood failure percentage (WFP) is an important index for evaluating the bond strength of plywood. Currently, the method used for detecting WFP is visual inspection, which lacks efficiency. In order to improve it, image processing methods are applied to wood failure detection. The present study used thresholding and K-means clustering algorithms in wood failure detection...

Effects of Small-Scale Dead Wood Additions on Beetles in Southeastern U.S. Pine Forests

Directory of Open Access Journals (Sweden)

Chris E. Carlton

2012-08-01

Full Text Available Pitfall traps were used to sample beetles (Coleoptera in plots with or without inputs of dead loblolly pine (Pinus taeda L. wood at four locations (Louisiana, Mississippi, North Carolina and Texas on the coastal plain of the southeastern United States. The plots were established in 1998 and sampling took place in 1998, 1999, and 2002 (only 1998 for North Carolina. Overall, beetles were more species rich, abundant and diverse in dead wood addition plots than in reference plots. While these differences were greatest in 1998 and lessened thereafter, they were not found to be significant in 1998 due largely to interactions between location and treatment. Specifically, the results from North Carolina were inconsistent with those from the other three locations. When these data were excluded from the analyses, the differences in overall beetle richness for 1998 became statistically significant. Beetle diversity was significantly higher in the dead wood plots in 1999 but by 2002 there were no differences between dead wood added and control plots. The positive influence of dead wood additions on the beetle community can be largely attributed to the saproxylic fauna (species dependent on dead wood, which, when analyzed separately, were significantly more species rich and diverse in dead wood plots in 1998 and 1999. Ground beetles (Carabidae and other species, by contrast, were not significantly affected. These results suggest manipulations of dead wood in pine forests have variable effects on beetles according to life history characteristics.

Charring does not affect wood infestation by subterranean termites

Science.gov (United States)

C.J. Peterson; P.D. Gerard; T.L. Wagner

2007-01-01

Fire is an important part of forest ecosystems, as is the insect fauna. Changes in wood brought aboutby fire may alter the ability of termites to use the wood, interrupting the decay cycle of woody debris.The ability of termites to find, infest, and feed upon wood after it had been charred was evaluated in

Growth and Wood/Bark Properties of Abies faxoniana Seedlings as Affected by Elevated CO2

Institute of Scientific and Technical Information of China (English)

Yun-Zhou Qiao; Yuan-Bin Zhang; Kai-Yun Wang; Qian Wang; Qi-Zhuo Tian

2008-01-01

Growth and wood and bark properties of Abies faxoniana seedlings after one year's exposure to elevated CO2 concentration (ambient + 350 (=1= 25) μmol/mol) under two planting densities (28 or 84 plants/mz) were investigated in closed-top chambers. Tree height, stem diameter and cross-sectional area, and total biomass were enhanced under elevated CO2 concentration, and reduced under high planting density. Most traits of stem bark were improved under elevated CO2 concentration and reduced under high planting density. Stem wood production was significantly increased in volume under elevated CO2 concentration under both densities, and the stem wood density decreased under elevated CO2 concentration and increased under high planting density. These results suggest that the response of stem wood and bark to elevated CO2 concentration is density dependent. This may be of great importance in a future CO2 enriched world in natural forests where plant density varies considerably. The results also show that the bark/wood ratio in diameter, stem cross-sectional area and dry weight are not proportionally affected by elevated CO2 concentration under the two contrasting planting densities. This indicates that the response magnitude of stem bark and stem wood to elevated CO2 concentration are different but their response directions are the same.

Modelling of the viscoelastic behaviour of steel reinforced thermoplastic pipes

NARCIS (Netherlands)

Kruijer, M.P.; Warnet, Laurent; Akkerman, Remko

2006-01-01

This paper describes the analysis of the time dependent behaviour of a steel reinforced thermoplastic pipe. This new class of composite pipes is constructed of a HDPE (high-density polyethylene) liner pipe, which is over wrapped with two layers of thermoplastic tape. The thermoplastic tapes are

Assessment and management of dead-wood habitat

Science.gov (United States)

Hagar, Joan

2007-01-01

The Bureau of Land Management (BLM) is in the process of revising its resource management plans for six districts in western and southern Oregon as the result of the settlement of a lawsuit brought by the American Forest Resource Council. A range of management alternatives is being considered and evaluated including at least one that will minimize reserves on O&C lands. In order to develop the bases for evaluating management alternatives, the agency needs to derive a reasonable range of objectives for key issues and resources. Dead-wood habitat for wildlife has been identified as a key resource for which decision-making tools and techniques need to be refined and clarified. Under the Northwest Forest Plan, reserves were to play an important role in providing habitat for species associated with dead wood (U.S. Department of Agriculture Forest Service and U.S. Department of the Interior Bureau of Land Management, 1994). Thus, the BLM needs to: 1) address the question of how dead wood will be provided if reserves are not included as a management strategy in the revised Resource Management Plan, and 2) be able to evaluate the effects of alternative land management approaches. Dead wood has become an increasingly important conservation issue in managed forests, as awareness of its function in providing wildlife habitat and in basic ecological processes has dramatically increased over the last several decades (Laudenslayer et al., 2002). A major concern of forest managers is providing dead wood habitat for terrestrial wildlife. Wildlife in Pacific Northwest forests have evolved with disturbances that create large amounts of dead wood; so, it is not surprising that many species are closely associated with standing (snags) or down, dead wood. In general, the occurrence or abundance of one-quarter to one-third of forest-dwelling vertebrate wildlife species, is strongly associated with availability of suitable dead-wood habitat (Bunnell et al., 1999; Rose et al., 2001). In

Wood preservation

Science.gov (United States)

Rebecca E. Ibach

1999-01-01

When left untreated in many outdoor applications, wood becomes subject to degradation by a variety of natural causes. Although some trees possess naturally occurring resistance to decay (Ch. 3, Decay Resistance), many are in short supply or are not grown in ready proximity to markets. Because most commonly used wood species, such as Southern Pine, ponderosa pine, and...

Survival, growth, wood basic density and wood biomass of seven ...

African Journals Online (AJOL)

A performance comparison of seven-year-old individuals of 13 Casuarina species/provenances in terms of survival, growth (diameter, height and volume), wood basic density and wood biomass was undertaken at Kongowe, Kibaha, Tanzania. The trial was laid out using a randomised complete block design with four ...

Production and Mechanical Characterization of Ballistic Thermoplastic Composite Materials

OpenAIRE

D. Korsacilar; C. Atas

2014-01-01

In this study, first thermoplastic composite materials /plates that have high ballistic impact resistance were produced. For this purpose, the thermoplastic prepreg and the vacuum bagging technique were used to produce a composite material. Thermoplastic prepregs (resin-impregnated fiber) that are supplied ready to be used, namely high-density polyethylene (HDPE) was chosen as matrix and unidirectional glass fiber was used as reinforcement. In order to compare the fiber c...

Patterns in hydraulic architecture from roots to branches in six tropical tree species from cacao agroforestry and their relation to wood density and stem growth

Directory of Open Access Journals (Sweden)

Martyna Malgorzata Kotowska

2015-03-01

Full Text Available For decades it has been assumed that the largest vessels are generally found in roots and that vessel size and corresponding sapwood area-specific hydraulic conductivity are acropetally decreasing towards the distal twigs. However, recent studies from the perhumid tropics revealed a hump-shaped vessel size distribution. Worldwide tropical perhumid forests are extensively replaced by agroforestry systems often using introduced species of various biogeographical and climatic origins. Nonetheless, it is unknown so far what kind of hydraulic architectural patterns are developed in those agroforestry tree species and which impact this exerts regarding important tree functional traits, such as stem growth, hydraulic efficiency and wood density. We investigated wood anatomical and hydraulic properties of the root, stem and branch wood in Theobroma cacao and five common shade tree species in agroforestry systems on Sulawesi (Indonesia; three of these were strictly perhumid tree species, and the other three tree species are tolerating seasonal drought. The overall goal of our study was to relate these properties to stem growth and other tree functional traits such as foliar nitrogen content and sapwood to leaf area ratio. Our results confirmed a hump-shaped vessel size distribution in nearly all species. Drought-adapted species showed divergent patterns of hydraulic conductivity, vessel density and relative vessel lumen area between root, stem and branch wood compared to wet forest species. Confirming findings from natural old-growth forests in the same region, wood density showed no relationship to specific conductivity. Overall, aboveground growth performance was better predicted by specific hydraulic conductivity than by foliar traits and wood density. Our study results suggest that future research on conceptual trade-offs of tree hydraulic architecture should consider biogeographical patterns underlining the importance of anatomical adaptation

Tannins in tropical woods

Energy Technology Data Exchange (ETDEWEB)

Doat, J

1978-01-01

A preliminary study was made of the chemistry of pyrogallol- and catecholtannins, their general properties and methods of extraction and determination. Three methods of estimation - Lowenthal, powdered hide and spectrophotometry - were compared using two control solutions, four samples of wood and one of bark. Using the empirical powdered hide method, tannins of both types were estimated in wood and bark of various tropical species (some separately and some as a mixture), Moroccan oaks (Quercus suber and Q. ilex), and European oak 9Q. petraea). Further tests were made on the wood and bark of the two mangrove species, Rhizophora mangle and R. racemosa, by subjecting them to successive extraction with a range of solvents. None of the woods tested had as much as the 10% of tannins considered necessary in economic sources. The bark of the two mangroves, of Eucalyptus urophylla and of Prosopis africana had tannin contents over 10% and the latter two species had very favorable tannin/non-tannin ratios. All the tropical species, with the probable exception of E. urophylla, had only catecholtannins. Only the oaks and E. urophylla bark gave positive results when tested for gallotannins.

Species verification of Dalbergia nigra and Dalbergia spruceana samples in the wood collection of the Forest Products Laboratory

Science.gov (United States)

Michael C. Wiemann; Edgard O. Espinoza

2017-01-01

To evade endangered timber species laws, unscrupulous importers sometimes attempt to pass protected Dalbergia nigra as look-alike but unprotected, Dalbergia Spruceana. Wood density and fluorescence properties are sometimes used to identify the species. Although these properties are useful and do not require special equipment,...

Climate Responses in Growth and Wood Anatomy of Imoprtant Forest Tree Species in Denmark

DEFF Research Database (Denmark)

Huang, Weiwei

and high temperatures on the development of Danish tree species are scarcely investigated. Through a dendroecological approach this dissertation assessed the growth responses related to increment, xylem anatomy and wood property of eight different important tree species, namely Picea abies (L.) Karst......., Picea sitchensis (Bong.) Carr., Abies alba Mill., Abies grandis (Dougl.) Lindl., Pseudotsuga mensiesii (Mirb.) Franco, Larix kaempferi (Lamb.) Carr., Quercus robur L. and Fagus sylvatica L., to long-term drought and high temperatures, aiming at identifying a species portfolio matching future climate...... intolerant species, mainly due to their low drought tolerance (both species) and susceptibility to high autumn temperature (only P. abies). Overall, this dissertation improves the understanding of how drought and high temperatures have impacted and will influence the growth of tree species in Danish forest...

Coniochaeta (Lecythophora), Collophora gen. nov. And Phaeomoniella species associated with wood necroses of Prunus trees

NARCIS (Netherlands)

Damm, U.; Fourie, P.H.; Crous, P.W.

2010-01-01

Species of the genus Coniochaeta (anamorph: Lecythophora) are known as pathogens of woody hosts, but can also cause opportunistic human infections. Several fungi with conidial stages resembling Lecythophora were isolated from necrotic wood samples of Prunus trees in South Africa. In order to reveal

Factors affecting sodium hypochlorite extraction of CCA from treated wood.

Science.gov (United States)

Gezer, E D; Cooper, P A

2009-12-01

Significant amounts of chromated copper arsenate (CCA) treated wood products, such as utility poles and residential construction wood, remain in service. There is increasing public concern about environmental contamination from CCA-treated wood when it is removed from service for reuse or recycling, placed in landfills or burned in commercial incinerators. In this paper, we investigated the effects of time, temperature and sodium hypochlorite concentration on chromium oxidation and extraction of chromated copper arsenate from CCA-treated wood (Type C) removed from service. Of the conditions evaluated, reaction of milled wood with sodium hypochlorite for one hour at room temperature followed by heating at 75 degrees C for two hours gave the highest extraction efficiency. An average of 95% Cr, 99% Cu and 96% As could be removed from CCA-treated, milled wood by this process. Most of the extracted chromium was oxidized to the hexavalent state and could therefore be recycled in a CCA treating solution. Sodium hypochlorite extracting solutions could be reused several times to extract CCA components from additional treated wood samples.

Wood anatomy of the Brazilian species of Swartizia and considerations within the tribe Swartzieae

Science.gov (United States)

Veronica Angyalossy-Alfonso

2002-01-01

Fifty-one Brazilian species and varieties of Swartzia Schreber and eight other genera from the tribe Swartzieae were examined. Features with the greatest diagnostic value for the tribe are intervascular pit size, ray width and frequency, storied structure, axial parenchyma strand length, parenchyma band width, and vessel diameter. We analyzed the wood anatomical data...

Textile impregnation with thermoplastic resin - models and application

NARCIS (Netherlands)

Loendersloot, Richard; Grouve, Wouter Johannes Bernardus; Lamers, E.A.D.; Wijskamp, Sebastiaan; Kelly, P.A.; Bickerton, S.; Lescher, P.; Govignon, Q.

2012-01-01

One of the key issues of the development of cost-effective thermoplastic composites for the aerospace industry is the process quality control. A complete, void free impregnation of the textile reinforcement by the thermoplastic resin is an important measure of the quality of composites. The

Subterranean Termite Resistance of Polystyrene-Treated Wood from Three Tropical Wood Species

Directory of Open Access Journals (Sweden)

Yusuf Sudo Hadi

2016-07-01

Full Text Available The objective of this work was to investigate the resistance of three Indonesian wood species to termite attack. Samples from sengon (Falcataria moluccana, mangium (Acacia mangium, and pine (Pinus merkusii were treated with polystyrene at loading levels of 26.0%, 8.6%, and 7.7%, respectively. Treated and untreated samples were exposed to environmental conditions in the field for 3 months. Untreated specimens of sengon, mangium, and pine had resistance ratings of 3.0, 4.6, and 2.4, respectively, based on a 10-point scale from 0 (no resistance to 10 (complete or near-complete resistance. Corresponding resistance values of 7.8, 7.2, and 8.2 were determined for specimens treated with polystyrene. Overall weight loss values of 50.3%, 23.3%, and 66.4% were found for untreated sengon, mangium, and pine samples, respectively; for treated samples, the values were 7.6%, 14.4%, and 5.1%, respectively. Based on the findings in this study, overall resistance to termite attack was higher for treated samples compared to untreated samples.

Temporal trends in 137Cs concentrations in the bark, sapwood, heartwood, and whole wood of four tree species in Japanese forests from 2011 to 2016.

Science.gov (United States)

Ohashi, Shinta; Kuroda, Katsushi; Takano, Tsutomu; Suzuki, Youki; Fujiwara, Takeshi; Abe, Hisashi; Kagawa, Akira; Sugiyama, Masaki; Kubojima, Yoshitaka; Zhang, Chunhua; Yamamoto, Koichi

2017-11-01

To understand the changes in radiocesium ( 137 Cs) concentrations in stem woods after the Fukushima Dai-ichi Nuclear Power Plant (FDNPP) accident, we investigated 137 Cs concentrations in the bark, sapwood, heartwood, and whole wood of four major tree species at multiple sites with different levels of radiocesium deposition from the FDNPP accident since 2011 (since 2012 at some sites): Japanese cedar at four sites, hinoki cypress and Japanese konara oak at two sites, and Japanese red pine at one site. Our previous report on 137 Cs concentrations in bark and whole wood samples collected from 2011 to 2015 suggested that temporal variations were different among sites even within the same species. In the present study, we provided data on bark and whole wood samples in 2016 and separately measured 137 Cs concentrations in sapwood and heartwood samples from 2011 to 2016; we further discussed temporal trends in 137 Cs concentrations in each part of tree stems, particularly those in 137 Cs distributions between sapwood and heartwood, in relation to their species and site dependencies. Temporal trends in bark and whole wood samples collected from 2011 to 2016 were consistent with those reported in samples collected from 2011 to 2015. Temporal variations in 137 Cs concentrations in barks showed either a decreasing trend or no clear trend, implying that 137 Cs deposition in barks is inhomogeneous and that decontamination is relatively slow in some cases. Temporal trends in 137 Cs concentrations in sapwood, heartwood, and whole wood were different among species and also among sites within the same species. Relatively common trends within the same species, which were increasing, were observed in cedar heartwood, and in oak sapwood and whole wood. On the other hand, the ratio of 137 Cs concentration in heartwood to that in sapwood (fresh weight basis) was commonly increased to more than 2 in cedar, although distinct temporal trends were not found in the other species, for

Postfire Burnt-Wood Management Affects Plant Damage by Ungulate Herbivores

Directory of Open Access Journals (Sweden)

Jorge Castro

2013-01-01

Full Text Available I analyze the effect of post-fire burnt wood management on herbivore attack on a woody plant species (Ulex parviflorus. Two experimental plots of ca. 20 hectares were established at two elevations in a burnt area in a Mediterranean mountain (Sierra Nevada, Spain. Three replicates of three treatments differing in post-fire burnt wood management were established per plot: “no intervention” (NI, all trees remained standing, “partial cut plus lopping” (PCL, felling the trees, cutting the main branches, and leaving all the biomass in situ, and “salvage logging” (SL; removal of logs and elimination of woody debris. Risk of herbivory and damage intensity were monitored for two years. The pattern of attack by ungulate herbivores varied among treatments and years. In any case, there was an overall reduction in the risk of herbivory in the PCL treatment, presumably because the highest habitat complexity in this treatment hampered ungulate movement and foraging. As a result, the burnt logs and branches spread over the ground acted as a physical barrier that protected seedlings from herbivores. This protection may be used for the regeneration of shrubs and trees, and it is of interest for the regeneration of burnt sites either naturally or by reforestation.

Wood nitrogen concentrations in tropical trees: phylogenetic patterns and ecological correlates.

Science.gov (United States)

Martin, Adam R; Erickson, David L; Kress, W John; Thomas, Sean C

2014-11-01

In tropical and temperate trees, wood chemical traits are hypothesized to covary with species' life-history strategy along a 'wood economics spectrum' (WES), but evidence supporting these expected patterns remains scarce. Due to its role in nutrient storage, we hypothesize that wood nitrogen (N) concentration will covary along the WES, being higher in slow-growing species with high wood density (WD), and lower in fast-growing species with low WD. In order to test this hypothesis we quantified wood N concentrations in 59 Panamanian hardwood species, and used this dataset to examine ecological correlates and phylogenetic patterns of wood N. Wood N varied > 14-fold among species between 0.04 and 0.59%; closely related species were more similar in wood N than expected by chance. Wood N was positively correlated with WD, and negatively correlated with log-transformed relative growth rates, although these relationships were relatively weak. We found evidence for co-evolution between wood N and both WD and log-transformed mortality rates. Our study provides evidence that wood N covaries with tree life-history parameters, and that these patterns consistently co-evolve in tropical hardwoods. These results provide some support for the hypothesized WES, and suggest that wood is an increasingly important N pool through tropical forest succession. © 2014 The Authors. New Phytologist © 2014 New Phytologist Trust.

Fruit production and branching density affect shoot and whole-tree wood to leaf biomass ratio in olive.

Science.gov (United States)

Rosati, Adolfo; Paoletti, Andrea; Al Hariri, Raeed; Famiani, Franco

2018-02-14

biomass ratio is likely to affect the canopy's ability to export carbon (i.e., towards fruits), as shoot wood to leaf biomass ratio affects the carbon export ability of the shoot. © The Author(s) 2018. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Wood anatomy of Argyroxiphium (Asteraceae): adaptive radiation and ecological correlations

International Nuclear Information System (INIS)

Carlquist, S.

1997-01-01

Wood anatomy shows close correlation with ecology: A. kauense, A. sandwicense (stem), and A. virescens, which occur in dry localities, show xeromorphic wood patterns. The most mesomorphic woods are those of the bog species A. grayanum and root wood of A. sandwicense. The wood of A. caliginis is xeromorphic, despite the bog habitat of the species, a fact explainable if A. caliginis is a recent entrant into the bog habitat Libriform wall thickness appears correlated with habit. Quantitative features of stem woods of Argyroxiphium are comparable to woods ranging from desert to moist montane forest areas in California. The similarities to woods from each Californian habitat are correlative to the relative moisture availability of the respective Hawaiian habitats of the Argyroxiphium species. (author)

Can we relate respiration rates of bark and wood with tissue nitrogen concentrations and branch-level CO2 fluxes across woody species?

Science.gov (United States)

Eller, A. S.; Wright, I.; Cernusak, L. A.

2013-12-01

Respiration from above-ground woody tissue is generally responsible for 5-15% of ecosystem respiration (~ 30% of total above-ground respiration). The CO2 respired by branches comes from both the sapwood and the living layers within the bark, but because there is considerable movement of respired CO2 within woody tissues (e.g. in the transpiration stream), and because the bark can present a considerable barrier to CO2 diffusion, it can be difficult to interpret measured CO2 efflux from intact branches in relation to the respiration rates of the component tissues, and to relative mass allocation to each. In this study we investigated these issues in 15 evergreen tree and shrub species native to the Sydney area in eastern Australia. We measured CO2 efflux and light-dependent refixation of respired CO2 in photosynthetic bark from the exterior surfaces of branches (0.5-1.5 cm in diameter), and measured the tissue-specific respiration rates of the bark and wood from those same branches. We also measured the nitrogen content and tissue density of the wood and bark to determine: 1) Among species, what is the relationship between %N and tissue respiration? 2) How is photosynthetic refixation of CO2 related to respiration and %N in the bark and underlying wood? and 3) What is the relationship between branch CO2 efflux and the respiration rates of the underlying wood and bark that make up the branch? Across the 15 species %N was a better predictor of respiration in wood than in bark. CO2 efflux measured from the exterior of the stem in the dark was positively correlated with photosynthetic refixation and explained ~40% of the variation in rates of refixation. Refixation rates were not strongly related to bark or wood %N. Differences among species in CO2 efflux rates were not well explained by differences in bark or wood %N and there was a stronger relationship between bark respiration and CO2 efflux than between wood respiration and CO2 efflux. These results suggest that the

Changes of wood anatomical characters of selected species of Araucaria- during artificial charring - implications for palaeontology

Directory of Open Access Journals (Sweden)

Isa Carla Osterkamp

2017-11-01

Full Text Available ABSTRACT Charcoal is widely accepted as evidence of the occurrence of palaeo-wildfire. Although fossil charcoal remains have been used in many studies, investigation into the anatomical changes occurring during charring are few. The present study analyses changes in selected anatomical characters during artificial charring of modern wood of three species of the genus Araucaria (i.e. Araucaria angustifolia, Araucaria bidwillii and Araucaria columnaris. Wood samples of the studied species was charred under controlled conditions at varying temperatures. Measurements of anatomical features of uncharred wood and artificial charcoal were statistically analysed. The anatomical changes were statistically correlated with charring temperatures and most of the parameters showed marked decreases with increasing charring temperature. Compared to the intrinsic variability in anatomical features, both within and between growth rings of an individual plant, the changes induced by temperature account only for a comparatively small percentage of the observed variability. Regarding Araucaria charcoal, it seems possible that at least general taxonomic and palaeoenvironmental implications can be drawn from such material. However, it is not clear so far whether these results and interpretations based on only three taxa, can be generalized for the entire family and anatomically similar fossil taxa or not.

Comparative hydraulic architecture of tropical tree species representing a range of successional stages and wood density.

Science.gov (United States)

McCulloh, Katherine A; Meinzer, Frederick C; Sperry, John S; Lachenbruch, Barbara; Voelker, Steven L; Woodruff, David R; Domec, Jean-Christophe

2011-09-01

Plant hydraulic architecture (PHA) has been linked to water transport sufficiency, photosynthetic rates, growth form and attendant carbon allocation. Despite its influence on traits central to conferring an overall competitive advantage in a given environment, few studies have examined whether key aspects of PHA are indicative of successional stage, especially within mature individuals. While it is well established that wood density (WD) tends to be lower in early versus late successional tree species, and that WD can influence other aspects of PHA, the interaction of WD, successional stage and the consequent implications for PHA have not been sufficiently explored. Here, we studied differences in PHA at the scales of wood anatomy to whole-tree hydraulic conductance in species in early versus late successional Panamanian tropical forests. Although the trunk WD was indistinguishable between the successional groups, the branch WD was lower in the early successional species. Across all species, WD correlated negatively with vessel diameter and positively with vessel packing density. The ratio of branch:trunk vessel diameter, branch sap flux and whole-tree leaf-specific conductance scaled negatively with branch WD across species. Pioneer species showed greater sap flux in branches than in trunks and a greater leaf-specific hydraulic conductance, suggesting that pioneer species can move greater quantities of water at a given tension gradient. In combination with the greater water storage capacitance associated with lower WD, these results suggest these pioneer species can save on the carbon expenditure needed to build safer xylem and instead allow more carbon to be allocated to rapid growth.

PREPARATION AND CHARACTERIZATION OF COMPOSITES COMPRISING MODIFIED HARDWOOD AND WOOD POLYMERS/POLY(VINYL CHLORIDE

Directory of Open Access Journals (Sweden)

Ruxanda Bodîrlău

Full Text Available Chemical modification of hardwood sawdust from ash-tree species was carried out with a solution of maleic anhydride in acetone. Wood polymers, lignin, and cellulose were isolated from the wood sawdust and modified by the same method. Samples were characterized by Fourier transform infrared spectroscopy (FTIR, providing evidence that maleic anhydride esterifies the free hydroxyl groups of the wood polymer components. Composites comprising chemically modified wood sawdust and wood polymers (cellulose, lignin-as variable weight percentages-, and poly (vinyl chloride were obtained and further characterized by using FTIR spectroscopy and scanning electron microscopy (SEM. The thermal behavior of composites was investigated by using the thermogravimetric analysis (TGA. In all cases, thermal properties were affected by fillers addition.

Manufacturing a 9-Meter Thermoplastic Composite Wind Turbine Blade: Preprint

Energy Technology Data Exchange (ETDEWEB)

Murray, Robynne [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Snowberg, David R [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Berry, Derek S [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Beach, Ryan [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Rooney, Samantha A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Swan, Dana [Arkema Inc.

2017-12-06

Currently, wind turbine blades are manufactured from a combination of glass and/or carbon fiber composite materials with a thermoset resin such as epoxy, which requires energy-intensive and expensive heating processes to cure. Newly developed in-situ polymerizing thermoplastic resin systems for composite wind turbine blades polymerize at room temperature, eliminating the heating process and significantly reducing the blade manufacturing cycle time and embodied energy, which in turn reduces costs. Thermoplastic materials can also be thermally welded, eliminating the need for adhesive bonds between blade components and increasing the overall strength and reliability of the blades. As well, thermoplastic materials enable end-of-life blade recycling by reheating and decomposing the materials, which is a limitation of existing blade technology. This paper presents a manufacturing demonstration for a 9-m-long thermoplastic composite wind turbine blade. This blade was constructed in the Composites Manufacturing Education and Technology facility at the National Wind Technology Center at the National Renewable Energy Laboratory (NREL) using a vacuum-assisted resin transfer molding process. Johns Manville fiberglass and an Arkema thermoplastic resin called Elium were used. Additional materials included Armacell-recycled polyethylene terephthalate foam from Creative Foam and low-cost carbon- fiber pultruded spar caps (manufactured in collaboration with NREL, Oak Ridge National Laboratory, Huntsman, Strongwell, and Chomarat). This paper highlights the development of the thermoplastic resin formulations, including an additive designed to control the peak exothermic temperatures. Infusion and cure times of less than 3 hours are also demonstrated, highlighting the efficiency and energy savings associated with manufacturing thermoplastic composite blades.

Feedbacks between earlywood anatomy and non-structural carbohydrates affect spring phenology and wood production in ring-porous oaks

Science.gov (United States)

Pérez-de-Lis, Gonzalo; García-González, Ignacio; Rozas, Vicente; Olano, José Miguel

2016-10-01

Non-structural carbohydrates (NSC) play a central role in the construction and maintenance of a tree's vascular system, but feedbacks between the NSC status of trees and wood formation are not fully understood. We aimed to evaluate multiple dependencies among wood anatomy, winter NSC, and phenology for coexisting temperate (Quercus robur) and sub-Mediterranean (Q. pyrenaica) oaks along a water-availability gradient in the NW Iberian Peninsula. Sapwood NSC concentrations were quantified at three sites in December 2012 (N = 240). Leaf phenology and wood anatomy were surveyed in 2013. Structural equation modelling was used to analyse the interplay among hydraulic diameter (Dh), winter NSC, budburst date, and earlywood vessel production (EVP), while the effect of Dh and EVP on latewood width was assessed by using a mixed-effects model. NSC and wood production increased under drier conditions for both species. Q. robur showed a narrower Dh and lower soluble sugar (SS) concentration (3.88-5.08 % dry matter) than Q. pyrenaica (4.06-5.57 % dry matter), but Q. robur exhibited larger EVP and wider latewood (1403 µm) than Q. pyrenaica (667 µm). Stem diameter and Dh had a positive effect on SS concentrations, which were related to an earlier leaf flushing in both species. Sapwood sugar content appeared to limit EVP exclusively in Q. pyrenaica. In turn, Dh and EVP were found to be key predictors of latewood growth. Our results confirm that sapwood SS concentrations are involved in modulating growth resumption and xylem production in spring. Q. pyrenaica exhibited a tighter control of carbohydrate allocation to wood formation than Q. robur, which would play a role in protecting against environmental stress in the sub-Mediterranean area.

Manufacturing of a REBCO racetrack coil using thermoplastic resin aiming at Maglev application

International Nuclear Information System (INIS)

Mizuno, Katsutoshi; Ogata, Masafumi; Hasegawa, Hitoshi

2015-01-01

Highlights: • We propose a novel REBCO coil structure which applies thermoplastic resin. • The thermoplastic resin bonds the coil winding and cooling plates. • The adhesiveness of the resin is strong enough to withstand the thermal stress. • The thermoplastic resin does not cause the degradation because of its high viscosity. • We successfully made a full-scale racetrack REBCO coil with the thermoplastic resin. - Abstract: The REBCO coated conductor is a promising technology for the Maglev application in terms of its high critical temperature. The operating temperature of the on-board magnets can be around 40–50 K with the coated conductor. The REBCO coils are cooled by cryocoolers directly, and hence the thermal design of the REBCO coils significantly changes from that of LTS coils. We have developed a novel REBCO coil structure using thermoplastic resin. The coil is not impregnated and the thermoplastic resin is used to bond the coil winding and the heat transfer members, e.g. copper and aluminum plates. The viscosity of the thermoplastic resin is high enough for the thermoplastic resin not to permeate between the turns in the coil. Therefore, the thermal stress does not occur and the risk of degradation is removed. This paper contains the following three topics. First, the thermal resistance of the thermoplastic resin was measured at cryogenic temperature. Then, a small round REBCO coil was experimentally produced. It has been confirmed that the thermoplastic resin does not cause the degradation and, the adhesion between the coil winding and copper plates withstands the thermal stress. Finally, we successfully produced a full-scale racetrack REBCO coil applying the coil structure with the thermoplastic resin.

Manufacturing of a REBCO racetrack coil using thermoplastic resin aiming at Maglev application

Energy Technology Data Exchange (ETDEWEB)

Mizuno, Katsutoshi, E-mail: mizuno.katsutoshi.14@rtri.or.jp; Ogata, Masafumi; Hasegawa, Hitoshi

2015-11-15

Highlights: • We propose a novel REBCO coil structure which applies thermoplastic resin. • The thermoplastic resin bonds the coil winding and cooling plates. • The adhesiveness of the resin is strong enough to withstand the thermal stress. • The thermoplastic resin does not cause the degradation because of its high viscosity. • We successfully made a full-scale racetrack REBCO coil with the thermoplastic resin. - Abstract: The REBCO coated conductor is a promising technology for the Maglev application in terms of its high critical temperature. The operating temperature of the on-board magnets can be around 40–50 K with the coated conductor. The REBCO coils are cooled by cryocoolers directly, and hence the thermal design of the REBCO coils significantly changes from that of LTS coils. We have developed a novel REBCO coil structure using thermoplastic resin. The coil is not impregnated and the thermoplastic resin is used to bond the coil winding and the heat transfer members, e.g. copper and aluminum plates. The viscosity of the thermoplastic resin is high enough for the thermoplastic resin not to permeate between the turns in the coil. Therefore, the thermal stress does not occur and the risk of degradation is removed. This paper contains the following three topics. First, the thermal resistance of the thermoplastic resin was measured at cryogenic temperature. Then, a small round REBCO coil was experimentally produced. It has been confirmed that the thermoplastic resin does not cause the degradation and, the adhesion between the coil winding and copper plates withstands the thermal stress. Finally, we successfully produced a full-scale racetrack REBCO coil applying the coil structure with the thermoplastic resin.

Variation in wood anatomy of species with a distribution covering both rain forest and savanna areas of the Ivory Coast, West-Africa

NARCIS (Netherlands)

Outer, den R.W.; Veenendaal, van W.L.H.

1976-01-01

The variation in wood anatomy within 30 hardwood species, each with a distribution covering both rain forest and savanna areas of the Ivory Coast, Africa, has been studied. Compared to specimens from the rain forest, material from the savanna tends to have more wood ray tissue (rays are higher,

The relationship between canopy cover and colony size of the wood ant Formica lugubris--implications for the thermal effects on a keystone ant species.

Directory of Open Access Journals (Sweden)

Yi-Huei Chen

Full Text Available Climate change may affect ecosystems and biodiversity through the impacts of rising temperature on species' body size. In terms of physiology and genetics, the colony is the unit of selection for ants so colony size can be considered the body size of a colony. For polydomous ant species, a colony is spread across several nests. This study aims to clarify how climate change may influence an ecologically significant ant species group by investigating thermal effects on wood ant colony size. The strong link between canopy cover and the local temperatures of wood ant's nesting location provides a feasible approach for our study. Our results showed that nests were larger in shadier areas where the thermal environment was colder and more stable compared to open areas. Colonies (sum of nests in a polydomous colony also tended to be larger in shadier areas than in open areas. In addition to temperature, our results supported that food resource availability may be an additional factor mediating the relationship between canopy cover and nest size. The effects of canopy cover on total colony size may act at the nest level because of the positive relationship between total colony size and mean nest size, rather than at the colony level due to lack of link between canopy cover and number of nests per colony. Causal relationships between the environment and the life-history characteristics may suggest possible future impacts of climate change on these species.

Study of Radiation Shielding Properties of selected Tropical Wood Species for X-rays in the 50-150 keV Range

Directory of Open Access Journals (Sweden)

S. Aggrey-Smith

2016-03-01

Full Text Available This paper compares the attenuation coefficients of 20 tropical hard wood species based on their linear and mass attenuation and half value layer (HVL properties for X-rays of energy 50–150 keV using a narrow collimated beam from a Cs-137 source. The narrow collimated beam method made corrections from multiple and small-angle scatterings of photons unnecessary. The attenuation depended on the chemical composition and densities of the wood species. The linear attenuation coefficients of wood species at 50–150 keV were highest for Pterygota macrocarpa (4.53 m−1 and lowest for Antiaris africana (1.24 m−1; the mass attenuation coefficient was highest for Triplochiton scleroxylon (17.62 m2/kg and lowest for Nesogordonia papaverifera (2.27 m2/kg.The HVL was highest for Antiaris africana (0.27 m and lowest for Pterygota macrocarpa (0.149 m. Pterygota macrocarpa of about 0.36 m thickness could serve as a more affordable radiation shielding material against secondary scatter and leakage radiations in place of lead, copper or concrete for low X-ray radiations up to 150 keV.

Tool-ply friction in thermoplastic composite forming (CD-rom)

NARCIS (Netherlands)

ten Thije, R.H.W.; Akkerman, Remko; van der Meer, L.; Ubbink, M.P.; Boisse, P.

2008-01-01

Friction is an important phenomenon that can dominate the resulting product geometry of thermoplastic composites upon forming. A model was developed that predicts the friction between a thermoplastic laminate and a rigid tool. The mesoscopic model, based on the Reynolds’ equation for thin film

Microstructure And Mechanical Properties Of Lead Oxide- Thermoplastic Elas Tomer Composite

International Nuclear Information System (INIS)

Sudirman; Handayani, Ari; Darwinto, Tri; Teguh, Yulius S.P.P.; Sunarni, Anik; Marlijanti, Isni

2000-01-01

Research on microstructure and mechanical properties of lead oxide-thermoplastic elastomer composite with Pb 3 O 4 as lead oxide. Thermoplastic elastomer synthesized from natural rubber as the elastomer and methyl metacrilate as the thermoplastic and irradiated simultaneously with optimum gamma ray. Thermoplastic elastomer (NR-PMMA) grind in a laboplastomill and Pb 3 O 4 was added in varied amount of 10%. 30%. 40% and 50%wt.The results showed that mechanical properties (tensile strength and elongation break) decreased as the Pb 3 O 4 composition increased. Microstructure from SEM observation showed that Pb 3 O 4 distributed evenly and having function as filler in composite

Attribute based selection of thermoplastic resin for vacuum infusion process

DEFF Research Database (Denmark)

Prabhakaran, R.T. Durai; Lystrup, Aage; Løgstrup Andersen, Tom

2011-01-01

The composite industry looks toward a new material system (resins) based on thermoplastic polymers for the vacuum infusion process, similar to the infusion process using thermosetting polymers. A large number of thermoplastics are available in the market with a variety of properties suitable...... for different engineering applications, and few of those are available in a not yet polymerised form suitable for resin infusion. The proper selection of a new resin system among these thermoplastic polymers is a concern for manufactures in the current scenario and a special mathematical tool would...... be beneficial. In this paper, the authors introduce a new decision making tool for resin selection based on significant attributes. This article provides a broad overview of suitable thermoplastic material systems for vacuum infusion process available in today’s market. An illustrative example—resin selection...

Chronic human disturbance affects plant trait distribution in a seasonally dry tropical forest

Science.gov (United States)

Sfair, Julia C.; de Bello, Francesco; de França, Thaysa Q.; Baldauf, Cristina; Tabarelli, Marcelo

2018-02-01

The effects of human disturbance on biodiversity can be mediated by environmental conditions, such as water availability, climate and nutrients. In general, disturbed, dry or nutrient-depleted soils areas tend to have lower taxonomic diversity. However, little is known about how these environmental conditions affect functional composition and intraspecific variability in tropical dry forests. We studied a seasonally dry tropical forest (SDTF) under chronic anthropogenic disturbance (CAD) along rainfall and soil nutrient gradients to understand how these factors influence the taxonomic and functional composition. Specifically we evaluated two aspects of CAD, wood extraction and livestock pressure (goat and cattle grazing), along soil fertility and rainfall gradients on shrub and tree traits, considering species turnover and intraspecific variability. In addition, we also tested how the traits of eight populations of the most frequent species are affected by wood extraction, livestock pressure, rainfall and soil fertility. In general, although CAD and environmental gradients affected each trait of the most widespread species differently, the most abundant species also had a greater variation of traits. Considering species turnover, wood extraction is associated with species with a smaller leaf area and lower investment in leaf mass, probably due to the indirect effects of this disturbance type on the vegetation, i.e. the removal of branches and woody debris clears the vegetation, favouring species that minimize water loss. Livestock pressure, on the other hand, affected intraspecific variation: the herbivory caused by goats and cattle promoted individuals which invest more in wood density and leaf mass. In this case, the change of functional composition observed is a direct effect of the disturbance, such as the decrease of palatable plant abundance by goat and cattle herbivory. In synthesis, CAD, rainfall and soil fertility can affect trait distribution at community

Plant diversity and energy potency of community forest in East Kalimantan, Indonesia: Searching for fast growing wood species for energy production

Directory of Open Access Journals (Sweden)

RUDIANTO AMIRTA

2016-05-01

Full Text Available Abstract. Amirta R, Yuliansyah, Angi EM, Ananto BR, Setiyono B, Haqiqi MT, Septiana HA, Lodong M, Oktavianto RN. 2016. Plant diversity and energy potency of community forest in East Kalimantan, Indonesia: Searching for fast growing wood species for energy production. Nusantara Bioscience 8: 22-30. Nowadays, there is an increasing interest in intensifying the production and use of biomass to replace fossil fuels for the production of heat and electricity, especially for a remote area that generally abundance with the wood biomass resources including in East Kalimantan, Indonesia. In this work, diversity of plant species that commonly growth in community forest area of East Kutai District, East Kalimantan, Indonesia had been studied to point out their energy potency to be used as biomass feedstock for the electricity generated. Diversity of plant species in the community forest was evaluated by making 13 sampling plots with 20mx20m size approximately. Concurently, the energy properties of plant biomass such as proximate and ultimate compositions were also analyzed using ASTM methods. Results showed that more than 30 species of tropical trees and wood shrubs were grown in the community forest. The presence of them was classified into two different growth of origins: natural and artificial plantation, and also three different categories of plant resources: tree species from logged over forest, commercial fast growing plant tree species for the fiber production and woody shrubs. The highest dominancy and productivity was found in Paraserianthes falcataria (L. Nielsen since the wood biomass was artificially planted for the commercial purposes. Among the 31 plant species analyzed we found the highest energy potency was obtained from Cratoxylum cochinchinense (Lour. Blume that produced 3.17 MWh/ton, and the lowest was from Trema orientalis (L. Blume 0.97 MWh/ton. The woody shrubs species such as Vernonia amigdalina Delile., Piper aduncum L., Gliricidia

Methods for Mitigating the Environmental Risks Associated with Wood Preservatives

Science.gov (United States)

Dennis Hayward; Stan T. Lebow; Kenneth M. Brooks

2011-01-01

As noted in earlier chapters, the treatment of wood is both art and science. Wood is a variable material; treatment results tend to vary with the preservative and wood species and even within boards of the same species. This means that treated wood often contains a range of preservative retentions. Some pieces will have less than the desired retention, while others may...

Micrandra inundata (Euphorbiaceae), a new species with unusual wood anatomy from black-water river banks in southern Venezuela

Science.gov (United States)

Paul E. Berry; Alex C. Wiedenhoeft

2004-01-01

Micrandra inundata is a distinctive new species adapted to seasonally flooded black-water river banks in southern Venezuela. Trees rarely exceed 10 m in height but have thick basal trunks composed of very lightweight wood. It has the smallest leaves and fruits of any known Micrandra species and appears to be most closely related to M. minor Benth. The botanical...

Multi-scale thermal stability of a hard thermoplastic protein-based material

Science.gov (United States)

Latza, Victoria; Guerette, Paul A.; Ding, Dawei; Amini, Shahrouz; Kumar, Akshita; Schmidt, Ingo; Keating, Steven; Oxman, Neri; Weaver, James C.; Fratzl, Peter; Miserez, Ali; Masic, Admir

2015-09-01

Although thermoplastic materials are mostly derived from petro-chemicals, it would be highly desirable, from a sustainability perspective, to produce them instead from renewable biopolymers. Unfortunately, biopolymers exhibiting thermoplastic behaviour and which preserve their mechanical properties post processing are essentially non-existent. The robust sucker ring teeth (SRT) from squid and cuttlefish are one notable exception of thermoplastic biopolymers. Here we describe thermoplastic processing of squid SRT via hot extrusion of fibres, demonstrating the potential suitability of these materials for large-scale thermal forming. Using high-resolution in situ X-ray diffraction and vibrational spectroscopy, we elucidate the molecular and nanoscale features responsible for this behaviour and show that SRT consist of semi-crystalline polymers, whereby heat-resistant, nanocrystalline β-sheets embedded within an amorphous matrix are organized into a hexagonally packed nanofibrillar lattice. This study provides key insights for the molecular design of biomimetic protein- and peptide-based thermoplastic structural biopolymers with potential biomedical and 3D printing applications.

Extractive and anatomical wood structure effects on mechanical properties of Caoba wood (Swietenia macrophylla King)

International Nuclear Information System (INIS)

Arevalo Fuentes Rosven Libardo; Hernandez Roger

2008-01-01

The compression tangential to grain of samples of mahogany wood from Peru was examined at different relative humidity levels at 25 Celsius degrade to determine the influence of both extractives and anatomical structure. Matched samples were used to assess the percentage of extractive components by extraction with solvents of increasing polarity: cyclohexane, dichloromethane, acetone, methanol and hot water. Additionally, fourteen anatomical parameters were determined by image analysis. Stepwise regression analysis concluded that mainly anatomical features, such as rays and vessels, rather than extractives, affect the mechanical behaviour of mahogany. These findings are agree with earlier results showing a negative effect of large and multiseriate rays on the mechanical properties of wood when loaded perpendicularly to their long axis. The influence of lumen located extracts soluble in dichloromethane might disallow deformations. Finally, it is postulated that hot water extracts may play a plasticizing role in this species.

Sound quality assessment of wood for xylophone bars.

Science.gov (United States)

Aramaki, Mitsuko; Baillères, Henri; Brancheriau, Loïc; Kronland-Martinet, Richard; Ystad, Sølvi

2007-04-01

Xylophone sounds produced by striking wooden bars with a mallet are strongly influenced by the mechanical properties of the wood species chosen by the xylophone maker. In this paper, we address the relationship between the sound quality based on the timbre attribute of impacted wooden bars and the physical parameters characterizing wood species. For this, a methodology is proposed that associates an analysis-synthesis process and a perceptual classification test. Sounds generated by impacting 59 wooden bars of different species but with the same geometry were recorded and classified by a renowned instrument maker. The sounds were further digitally processed and adjusted to the same pitch before being once again classified. The processing is based on a physical model ensuring the main characteristics of the wood are preserved during the sound transformation. Statistical analysis of both classifications showed the influence of the pitch in the xylophone maker judgement and pointed out the importance of two timbre descriptors: the frequency-dependent damping and the spectral bandwidth. These descriptors are linked with physical and anatomical characteristics of wood species, providing new clues in the choice of attractive wood species from a musical point of view.

Lignin-Retaining Transparent Wood.

Science.gov (United States)

Li, Yuanyuan; Fu, Qiliang; Rojas, Ramiro; Yan, Min; Lawoko, Martin; Berglund, Lars

2017-09-11

Optically transparent wood, combining optical and mechanical performance, is an emerging new material for light-transmitting structures in buildings with the aim of reducing energy consumption. One of the main obstacles for transparent wood fabrication is delignification, where around 30 wt % of wood tissue is removed to reduce light absorption and refractive index mismatch. This step is time consuming and not environmentally benign. Moreover, lignin removal weakens the wood structure, limiting the fabrication of large structures. A green and industrially feasible method has now been developed to prepare transparent wood. Up to 80 wt % of lignin is preserved, leading to a stronger wood template compared to the delignified alternative. After polymer infiltration, a high-lignin-content transparent wood with transmittance of 83 %, haze of 75 %, thermal conductivity of 0.23 W mK -1 , and work-tofracture of 1.2 MJ m -3 (a magnitude higher than glass) was obtained. This transparent wood preparation method is efficient and applicable to various wood species. The transparent wood obtained shows potential for application in energy-saving buildings. © 2017 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Wood Anatomy in Several Genera of Nigerian Annonaceae

Directory of Open Access Journals (Sweden)

Olatunji Olusanya OLATUNJI

2014-03-01

Full Text Available The anatomical characteristic of the wood of Annona muricata, A. senegalensis, Xylopia aethiopica, A. glauca, A. squamosa, Cleistopholis patens, Monodora tenuifolia and Greenwayodendron suaviolis were investigated in search of their stable taxonomic attribute. Thirty-two wood samples were collected from eight species of Annonnaceae (four specimens each. Fixation of the most healthy and fresh wood of each species was done using 500 ml of FAA (Formalin Acetic Acid and dehydrated in a series of ethanol while infiltration was done using tertiary-butyl-alcohol prepared in accordance with Johansen’s method. The sectioning was carried out with a rotary microtome and the slide containing the wood samples were examined using power shots s70 camera attached to computer. The results revealed several interesting wood anatomical features such as the presence of numerous fibre, ray cells, vessels, absence of axial parenchyma in some species, growth ring ranges from distinct to indistinct. Rays are composed of upright cells in A. muricata, fibre tracheid are also uncommon in A. muricata but common in G. suaviolis. Axial parenchyma are common in A. glauca and A. squamosa but absent in other species. The wood structure of A. glauca and A. squamosa are similar to that of C. patens, but the absence of axial parenchyma distinguished it from them. The results are important in understanding the relationships between and within the species.

N-fertilization has different effects on the growth, carbon and nitrogen physiology, and wood properties of slow- and fast-growing Populus species.

Science.gov (United States)

Li, Hong; Li, Mengchun; Luo, Jie; Cao, Xu; Qu, Long; Gai, Ying; Jiang, Xiangning; Liu, Tongxian; Bai, Hua; Janz, Dennis; Polle, Andrea; Peng, Changhui; Luo, Zhi-Bin

2012-10-01

To investigate how N-fertilization affects the growth, carbon and nitrogen (N) physiology, and wood properties of poplars with contrasting growth characteristics, slow-growing (Populus popularis, Pp) and fast-growing (P. alba×P. glandulosa, Pg) poplar saplings were exposed to different N levels. Above-ground biomass, leaf area, photosynthetic rates (A), instantaneous photosynthetic nitrogen use efficiency (PNUE (i)), chlorophyll and foliar sugar concentrations were higher in Pg than in Pp. Foliar nitrate reductase (NR) activities and root glutamate synthase (GOGAT) activities were higher in Pg than in Pp as were the N amount and NUE of new shoots. Lignin contents and calorific values of Pg wood were less than that of Pp wood. N-fertilization reduced root biomass of Pg more than of Pp, but increased leaf biomass, leaf area, A, and PNUE(i) of Pg more than of Pp. Among 13 genes involved in the transport of ammonium or nitrate or in N assimilation, transcripts showed more pronounced changes to N-fertilization in Pg than in Pp. Increases in NR activities and N contents due to N-fertilization were larger in Pg than in Pp. In both species, N-fertilization resulted in lower calorific values as well as shorter and wider vessel elements/fibres. These results suggest that growth, carbon and N physiology, and wood properties are more sensitive to increasing N availability in fast-growing poplars than in slow-growing ones, which is probably due to prioritized resource allocation to the leaves and accelerated N physiological processes in fast-growing poplars under higher N levels.

Determination of the swelling velocity of different wood species and tissues depending on the cutting direction on microtome section level

Science.gov (United States)

Stuckenberg, Peter; Wenderdel, Christoph; Zauer, Mario

2018-06-01

Swelling velocity in dependence on the anatomical cutting direction of yew [Taxus baccata L.] and boxwood [Buxus sempervirens L.] was determined at temperature of 20 °C and at relative humidity of 10% and 100%. The investigations, conducted on a microtome section level, showed a similar behaviour for specimens of both wood species. It was possible to determine that the swelling velocity for yew and boxwood increases in its anatomical cutting directions. The longitudinal direction showed the lowest value, the tangential direction, by distinction, the highest value. Furthermore, a significant influence of early wood and late wood content on the swelling velocity for yew was detected.

USE OF CANDEIA’S (Eremanthus erythropappus WASTE WOOD

Directory of Open Access Journals (Sweden)

Rosimeire Cavalcante dos Santos

2008-09-01

Full Text Available The candeia (Eremanthus erythropappus is a native forest species with multiple uses and specially utilized as essential oils source. The use of the candeia´s waste wood after oil extraction for particle panels production becomes a viable alternative, avoiding environmental problems and increasing the availability of these products in the consuming market. This work verified the viability of producing wood-cement panels using waste wood generated after the extraction of candeia’s oil, in association with pinus and eucalipto woods. The experiment was installed according to a completely randomized design with three repetitions. The treatments were arranged according to a factorial 2 x 3 scheme (two wooden species and three replacement percentages of the woods by candeia’s waste. The results of the physical and mechanical property tests showed high potentiality of candeia waste wood, after oil extraction, in association with pinus and eucalipto wood for manufacturing wood-cement panels.

Chapter 9: Wood Energy

Science.gov (United States)

Francisco X. Aguilar; Karen Abt; Branko Glavonjic; Eugene Lopatin; Warren  Mabee

2016-01-01

The availabilty of information on wood energy continues to improve, particularly for commoditized woodfuels.  Wood energy consumption and production vary in the UNECE region because demand is strngly affected by weather and the prices of competing energy sources.  There has been an increase in wood energy in the power-and-heat sector in the EU28 and North American...

Computational modelling of a thermoforming process for thermoplastic starch

Science.gov (United States)

Szegda, D.; Song, J.; Warby, M. K.; Whiteman, J. R.

2007-05-01

Plastic packaging waste currently forms a significant part of municipal solid waste and as such is causing increasing environmental concerns. Such packaging is largely non-biodegradable and is particularly difficult to recycle or to reuse due to its complex composition. Apart from limited recycling of some easily identifiable packaging wastes, such as bottles, most packaging waste ends up in landfill sites. In recent years, in an attempt to address this problem in the case of plastic packaging, the development of packaging materials from renewable plant resources has received increasing attention and a wide range of bioplastic materials based on starch are now available. Environmentally these bioplastic materials also reduce reliance on oil resources and have the advantage that they are biodegradable and can be composted upon disposal to reduce the environmental impact. Many food packaging containers are produced by thermoforming processes in which thin sheets are inflated under pressure into moulds to produce the required thin wall structures. Hitherto these thin sheets have almost exclusively been made of oil-based polymers and it is for these that computational models of thermoforming processes have been developed. Recently, in the context of bioplastics, commercial thermoplastic starch sheet materials have been developed. The behaviour of such materials is influenced both by temperature and, because of the inherent hydrophilic characteristics of the materials, by moisture content. Both of these aspects affect the behaviour of bioplastic sheets during the thermoforming process. This paper describes experimental work and work on the computational modelling of thermoforming processes for thermoplastic starch sheets in an attempt to address the combined effects of temperature and moisture content. After a discussion of the background of packaging and biomaterials, a mathematical model for the deformation of a membrane into a mould is presented, together with its

Dosimetric effects of thermoplastic immobilizing devices on skin dose

International Nuclear Information System (INIS)

Adu-Poku Olivia

2017-07-01

This work shows the increase in surface dose caused by thermoplastic immobilizing masks used for positioning and immobilization of patients. Thermoplastics are organic materials which soften when they are heated. They can be formed after softening and retain their final shape when cooled. The use of these thermoplastic masks are relevant during patient treatment. However, it can lead to an increased skin dose. Measurements were done at source-to-surface distance of 80 cm for external radiation beams produced by cobalt 60 using the Farmer type ionization chamber and the Unidos electrometer. Measurements were carried out using various mask thicknesses and no mask material on a solid water phantom. The thermoplastic percentage depth dose (PDD), equivalent thickness of water of the various thicknesses of the mask and surface doses were determined. The increase in the surface dose caused by the thermoplastic mask was compared by looking at the PDD at depth 0 with and without the mask present and was found to increase between 0.76 and 0.79% with no mask for a field size of 5 x 5 cm 2 . It was found that, the presence of the mask shifted the percentage depth dose curve to lower values. The physical thermoplastic thickness was measured to be between 2.30 and 1.80 mm, and the equivalent thicknesses of water, d e , were determined to be 1.2, 1.15, 1.10 and 1.09 and 1.00 mm for the unstretched, 5 cm stretched, 10 cm stretched, 15 cm stretched and 20 cm stretched masks, respectively. This meant that, as the mask thickness decreased, its water equivalent thickness also decreased. The presence of the mask material did not increase the skin dose significantly ( less than 1%). (au)

Bacteria in decomposing wood and their interactions with wood-decay fungi.

Science.gov (United States)

Johnston, Sarah R; Boddy, Lynne; Weightman, Andrew J

2016-11-01

The fungal community within dead wood has received considerable study, but far less attention has been paid to bacteria in the same habitat. Bacteria have long been known to inhabit decomposing wood, but much remains underexplored about their identity and ecology. Bacteria within the dead wood environment must interact with wood-decay fungi, but again, very little is known about the form this takes; there are indications of both antagonistic and beneficial interactions within this fungal microbiome. Fungi are hypothesised to play an important role in shaping bacterial communities in wood, and conversely, bacteria may affect wood-decay fungi in a variety of ways. This minireview considers what is currently known about bacteria in wood and their interactions with fungi, and proposes possible associations based on examples from other habitats. It aims to identify key knowledge gaps and pressing questions for future research. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

How to make a beetle out of wood: multi-elemental stoichiometry of wood decay, xylophagy and fungivory.

Science.gov (United States)

Filipiak, Michał; Weiner, January

2014-01-01

The majority of terrestrial biomass is wood, but the elemental composition of its potential consumers, xylophages, differs hugely from that of wood. This causes a severe nutritional imbalance. We studied the stoichiometric relationships of 11 elements (C, N, P, K, Ca, Mg, Fe, Zn, Mn, Cu, Na) in three species of pine-xylem-feeding insects, Stictoleptura rubra, Arhopalus rusticus (Coleoptera, Cerambycidae) and Chalcophora mariana (Coleoptera, Buprestidae), to elucidate their mechanisms of tissue growth and to match their life histories to their dietary constraints. These beetles do not differ from other Coleoptera in their absolute elemental compositions, which are approximately 1000 (N), 100 (P, Cu) and 50 (K, Na) times higher than in dead but undecayed pine wood. This discrepancy diminishes along the wood decay gradient, but the elemental concentrations remain higher by an order of magnitude in beetles than in highly decayed wood. Numerical simulation of the life history of S. rubra shows that feeding on nutrient-poor undecayed wood would extend its development time to implausible values, whereas feeding on highly decomposed wood (heavily infected with fungi) would barely balance its nutritional budget during the long development period of this species. The changes in stoichiometry indicate that the relative change in the nutrient levels in decaying wood cannot be attributed solely to carbon loss resulting from decomposer respiration: the action of fungi substantially enriches the decaying wood with nutritional elements imported from the outside of the system, making it a suitable food for wood-eating invertebrates.

Fatty Acid Composition of Fourteen Wood-decaying Basidiomycete Species Growing in Permafrost Conditions

Directory of Open Access Journals (Sweden)

Daniil N. Olennikov

2014-03-01

Full Text Available The fatty acid (FA compositions of 14 wild wood-decaying basidiomycete species (Bjerkandera adusta, Daedaleopsis septentrionalis, Dichomitus squalens, Inonotus hispidus, I.radiatus, Irpex lacteus, Fomitopsis cajanderi, F.pinicola, F. rosea, Gloeophyllum protractum, Lenzites betulina, Phellinus pini, Trametes gibbosa, T. ochracea growing in permafrost conditions in Katanga region (Russian Federation were investigated using GC-MS. Generally, C18:2 ω 6 (linoleic acid, C18:1 ω 9 (oleic acid, C16:0 (palmitic acid and C20:0 (arachinic acid were found to be the major FA in fungal species. Data about chemical components of Daedaleopsis septentrionalis , Fomitopsis cajanderi and Gloeophyllum protractum were obtained at the first time. Increased level of degree of FA unsaturation was probably a result of extreme environmental conditions.

Nonlinear viscoelastic characterization of molten thermoplastic vulcanizates (TPV) through large amplitude harmonic experiments

Energy Technology Data Exchange (ETDEWEB)

Leblanc, Jean L. [University P. and M. Curie-Paris 6, Polymer Rheology and Processing, Vitry-sur-Seine (France)

2007-10-15

The so-called thermoplastic vulcanizates (TPV) are essentially blends of a crystalline thermoplastic polymer (e.g., polypropylene) and a vulcanizable rubber composition, prepared through a special process called dynamic vulcanization, which yields a fine dispersion of micron-size crosslinked rubber particles in a thermoplastic matrix. Such materials are by nature complex polymer systems, i.e., multiphase, heterogeneous, typically disordered materials for which structure is as important as composition. Correctly assessing their rheological properties is a challenging task for several reasons: first, even if the uniformity of their composition is taken for granted, TPV are indeed very complicated materials, not only heterogeneous but also with a morphology related to their composition; second, their morphology can be affected by the flow field used; third, the migration of small labile ingredients (e.g., oil, curative residue, etc.) can in the meantime significantly change the boundary flow conditions, for instance through self-lubrication due to phase separation of the oil, or wall slip, or both. The aims of the work reported were to investigate a series of commercial TPV through the so-called Fourier transform rheometry, a testing technique especially developed to accurately investigate the nonlinear viscoelastic domain. Results are tentatively interpreted in terms of material composition and structure. (orig.)

BEHAVIOR OF GLUED JOINTS OF EUCALYPTUS sp. SAWN WOOD

Directory of Open Access Journals (Sweden)

Octávio Barbosa Plaster

2008-09-01

Full Text Available This research evaluated eucalypt wood adhesion capacity. The material evaluated was a commercial sawn wood composed by a blend of species of the genus Eucalyptus. The adhesives used were resorcinol-formaldehyde and polyvinila acetate (PVAc. The wood was segregated in three density with 0% of moisture content: class 1; 2 and 3 that, when combined (class1 x class1; 2x2; 3x3; 1x2; 1x3; 2x3 resulted in six treatments. The performance of the adhesion was evaluated by the shear strength to parallel compression and by wood failure in the glue line. The obtained results allowed to conclude that the adhesion of the combinations of wood/adhesive presented satisfactory performance. The average shear strength of the joints were shown equivalent to the shear strength of the solid wood with similar performance of adhesion in the two adhesives. In general, resorcinol-formaldheyde adhesive presented higher values (74.41% for wood failure in the joints, but similar to all treatments. The adhesion of samples of higher density presented lower performance probably when only the values of wood failure are considered. The values for the strength of glued joints, in general, were similar when analyzed the results achieved with the resorcinol-formaldehyde adhesive- base 140,56 Kgf/cm2. To polyvinila acetate the values of wood failure decrease when the density increase (65.94%, but the resistance in the glue line was positively affected (140.25 Kgf/cm2. In general, the density influenced the adhesion of the joints for the employed adhesives.

Application of molecular genetic methods for identification of wood-decaying fungi in wood constructions

Directory of Open Access Journals (Sweden)

Elena Bobeková

2008-01-01

Full Text Available The aim of the paper is to evaluate the utilization of molecular biology methods for detection of wood decaying fungi directly from decomposed wood using a commercial DNA extraction kit developed for soil substrates (PowerSoil™ DNA isolation kit. The experiment based on dry rot fungus (Serpula lacrymans detection from inoculated wooden pieces under laboratory conditions was followed by field detection of wood-decaying fungi from wood structures on building constructions. Fungal DNA was identified using the PCR–based methods including species-specific PCR and sequencing of amplified ITS region of ribosomal DNA.

Determination of Screw and Nail Withdrawal Resistance of Some Important Wood Species

Directory of Open Access Journals (Sweden)

Alper Aytekin

2008-04-01

Full Text Available In this study, screw and nail withdrawal resistance of fir (Abies nordmanniana, oak (Quercus robur L. black pine (Pinus nigra Arnold and Stone pine (Pinus pinea L. wood were determined and compared. The data represent the testing of withdrawal resistance of three types of screws as smart, serrated and conventional and common nails. The specimens were prepared according to TS 6094 standards. The dimensions of the specimens were 5x5x15cm and for all of the directions. Moreover, the specimens were conditioned at ambient room temperature and 65±2% relative humidity. The screws and nails were installed according to ASTM-D 1761 standards. Nail dimensions were 2.5mm diameter and 50 mm length, conventional screws were 4x50mm, serrated screws were 4x45mm and smart screws were 4x50mm. Results show that the maximum screw withdrawal resistance value was found in Stone pine for the serrated screw. There were no significant differences between Stone pine and oak regarding screw withdrawal resistance values. Conventional screw yielded the maximum screw withdrawal resistance value in oak, followed by Stone pine, black pine and fir. Oak wood showed the maximum screw withdrawal resistance value for the smart screw, followed by Stone pine, black pine, and fir. Oak wood showed higher nail withdrawal resistances than softwood species. It was also determined that oak shows the maximum nail withdrawal resistance in all types. The nail withdrawal resistances at the longitudinal direction are lower with respect to radial and tangential directions.

Seven wood-inhabiting new species of the genus Trichoderma (Fungi, Ascomycota) in Viride clade.

Science.gov (United States)

Qin, Wen-Tao; Zhuang, Wen-Ying

2016-06-01

More than 200 recent collections of Trichoderma from China were examined and 16 species belonging to the Viride clade were identified based on integrated studies of phenotypic and molecular data. Among them, seven wood-inhabiting new species, T. albofulvopsis, T. densum, T. laevisporum, T. sinokoningii, T. sparsum, T. sphaerosporum and T. subviride, are found. They form trichoderma- to verticillium-like conidiophores, lageniform to subulate phialides and globose to ellipsoidal conidia, but vary greatly in colony features, growth rates, and sizes of phialides and conidia. To explore their taxonomic positions, the phylogenetic tree including all the known species of the Viride clade is constructed based on sequence analyses of the combined RNA polymerase II subunit b and translation elongation factor 1 alpha exon genes. Our results indicated that the seven new species were well-located in the Koningii, Rogersonii and Neorufum subclades as well as a few independent terminal branches. They are clearly distinguishable from any existing species. Morphological distinctions and sequence divergences between the new species and their close relatives were discussed.

PHYSICAL ANALYSIS OF QUALITY WOOD Melia azedarach

Directory of Open Access Journals (Sweden)

T. J. da Silva

2016-07-01

Full Text Available Forest species, in general, present a slow growth, which results and profits can manifest themselves in the long run, it becomes necessary the study and discovery of new species that may provide raw materials and return on invested capital more immediate, being that the Melia azedarach wood is a potential option. In the absence of information about, the objective of this paper is to determine its physical properties: basic density and shrinkage of the Melia azedarach species in the Itapeva-SP region. The data obtained in this study allow to classify wood Melia azedarach as wood of average density and good dimensional stability. Feature that makes it ideal for its use in furniture industry. The low amount of research related to quality of this wood prevents the commercial use of it to achieve its full potential harnessing its effectively, and essential investments in this field.

Identification of Four Wood Species by an Electronic Nose and by LIBS

Directory of Open Access Journals (Sweden)

Juliana R. Cordeiro

2012-01-01

Full Text Available This paper presents two complementary methods capable of identifying four wood species (Cedrela fissilis, Ocotea porosa, Hymenolobium petraeum, and Aspidosperma subincanum both by their volatile organic compounds and by the presence of 10 chemical elements: Al, B, Ca, Mg, Zn, Cu, Mn, Fe, Na, and Si. The volatile compounds were detected by an electronic nose formed by an array of three different conductive polymer gas sensors. The elemental determination was made by laser-induced breakdown spectrometry (LIBS. The emissions measured were treated by principal component analysis (PCA. Leave-one-out analysis showed a rate of hits of 100%.

Broad Anatomical Variation within a Narrow Wood Density Range—A Study of Twig Wood across 69 Australian Angiosperms

Science.gov (United States)

Ziemińska, Kasia; Westoby, Mark; Wright, Ian J.

2015-01-01

Objectives Just as people with the same weight can have different body builds, woods with the same wood density can have different anatomies. Here, our aim was to assess the magnitude of anatomical variation within a restricted range of wood density and explore its potential ecological implications. Methods Twig wood of 69 angiosperm tree and shrub species was analyzed. Species were selected so that wood density varied within a relatively narrow range (0.38–0.62 g cm-3). Anatomical traits quantified included wood tissue fractions (fibres, axial parenchyma, ray parenchyma, vessels, and conduits with maximum lumen diameter below 15 μm), vessel properties, and pith area. To search for potential ecological correlates of anatomical variation the species were sampled across rainfall and temperature contrasts, and several other ecologically-relevant traits were measured (plant height, leaf area to sapwood area ratio, and modulus of elasticity). Results Despite the limited range in wood density, substantial anatomical variation was observed. Total parenchyma fraction varied from 0.12 to 0.66 and fibre fraction from 0.20 to 0.74, and these two traits were strongly inversely correlated (r = -0.86, P area to sapwood area ratio, and modulus of elasticity (0.24 ≤|r|≤ 0.41, P area to sapwood area ratio (0.47 ≤|r|≤ 0.65, all P area spectrum. The fibre-parenchyma spectrum does not yet have any clear or convincing ecological interpretation. PMID:25906320

Broad Anatomical Variation within a Narrow Wood Density Range--A Study of Twig Wood across 69 Australian Angiosperms.

Science.gov (United States)

Ziemińska, Kasia; Westoby, Mark; Wright, Ian J

2015-01-01

Just as people with the same weight can have different body builds, woods with the same wood density can have different anatomies. Here, our aim was to assess the magnitude of anatomical variation within a restricted range of wood density and explore its potential ecological implications. Twig wood of 69 angiosperm tree and shrub species was analyzed. Species were selected so that wood density varied within a relatively narrow range (0.38-0.62 g cm-3). Anatomical traits quantified included wood tissue fractions (fibres, axial parenchyma, ray parenchyma, vessels, and conduits with maximum lumen diameter below 15 μm), vessel properties, and pith area. To search for potential ecological correlates of anatomical variation the species were sampled across rainfall and temperature contrasts, and several other ecologically-relevant traits were measured (plant height, leaf area to sapwood area ratio, and modulus of elasticity). Despite the limited range in wood density, substantial anatomical variation was observed. Total parenchyma fraction varied from 0.12 to 0.66 and fibre fraction from 0.20 to 0.74, and these two traits were strongly inversely correlated (r = -0.86, P area to sapwood area ratio, and modulus of elasticity (0.24 ≤|r|≤ 0.41, P area to sapwood area ratio (0.47 ≤|r|≤ 0.65, all P area spectrum. The fibre-parenchyma spectrum does not yet have any clear or convincing ecological interpretation.

Potential of Reinforced Indonesian Glulam Beams Using Grade I (Bengkirai, Grade II (Kamper, Grade III (Nyatoh Woods for Use in Structural Wood Design

Directory of Open Access Journals (Sweden)

Saptahari Sugiri

2016-05-01

Full Text Available Wood is a natural resource that is renewable and available in various species in tropical countries. Its abundancy in nature makes it easy to obtain, thus making it a nature friendly material for use in construction. Indonesia is the most important source of tropical wood in the world after Brazil, making the use of wood for structural elements very desirable. It is estimated that 4000 different varieties of wood exist in Indonesia. This estimate is based on the herbarium species collected by the Forestry Research Institute, currently counting nearly 4000 types of trees with a diameter of more than 40 cm. In the Indonesian wood structure code, the strength of woods is divided into 3 grades (grade I, II and III. This paper presents an evaluation of the mechanical properties of glulam wood sourced from native Indonesian timber: Bengkirai wood (grade I, Kamper wood (grade II, and Nyatoh wood (grade III, thus proving the potential for Indonesian wood as industrial structural elements in wooden constructions.

Wood Identification of 18th Century Furniture. Interpreting Wood Naming Inventoires

Directory of Open Access Journals (Sweden)

Rocio Astrid BERNAL

2011-09-01

Full Text Available The 18th century Portuguese church furniture represents an extraordinary richness recognised worldwide, which demands safeguarding and valorisation. The identification of the wood of furniture artworks is the most important component for its comprehension and preservation. In this work wood anatomical characters of an 18th century Portuguese decorative furniture set from the Colegiada de São Martinho de Cedofeita, in Porto, were analysed to identify the woods used for manufacturing and to clarify their common names. Furthermore, the objectives were to recognise some of the criteria for choice of wood as well as the source of each wood. The woods identified from 16 fragments belong to Apuleia sp., Acacia sp., Neolamarckia sp. and Castanea sativa. Apuleia sp. and Acacia sp. woods most likely arrived from Brazil, while the Neolamarckia sp. woods likely arrived from India and the C. sativa woods from Portugal. The results are in accordance with the known Portuguese colonial sea routes of the 15th -18th centuries. Interestingly the terms found in the inventories can refer to finishing methods instead to the name of the woods, as for instance “oil wood” can refer to “oiled wood” or “linseed oiled wood”. The species choice may be related to the mechanical properties of the wood as well as the original tree size. Two large planks of Acacia sp. were used for the top of the “Portuguese arcaz”, and Apuleia sp. was found on main structural elements of this set of furniture, suggesting that wood colour was also important. Woods from Neolamarckia sp. and C. sativa, were also identified, being Castanea wood present only in the most recent pieces of the furniture set.

Priority effects of early successional insects influence late successional fungi in dead wood.

Science.gov (United States)

Jacobsen, Rannveig Margrete; Birkemoe, Tone; Sverdrup-Thygeson, Anne

2015-11-01

Community assembly is an integral process in all ecosystems, producing patterns of species distributions, biodiversity, and ecosystem functioning. Environmental filters and colonization history govern the assembly process, but their relative importance varies depending on the study system. Dead wood decomposition is a slow process, allowing decomposer communities to develop within a slowly changing substrate for decades. Despite this, there are few long-term studies of priority effects from colonization history in this ecosystem. In this study, we investigate the importance of insects in early succession of dead wood on the fungal community present one decade later. Sixty aspen trees were killed in two study landscapes, each tree producing one aspen high stump and log. Insects were sampled with flight interception traps during the first 4 years after tree death, and fungal fruiting bodies were registered in year twelve. We found positive priority effects of two fungivorous beetles, the sap beetle Glischrochilus quadripunctatus and the round fungus beetle Agathidium nigripenne, on the Artist's bracket (Ganoderma applanatum) and a positive priority effect of wood-boring beetles on the ascomycete Yellow fairy cup (Bisporella citrina). The Aspen bracket (Phellinus tremulae) did not respond to insects in early succession of the dead wood. Our results suggest that early successional insects can have significant, long-lasting effects on the late successional fungal community in dead wood. Also, the effect can be specific, with one fungus species depending on one or a few fungivorous beetle species. This has implications for decomposition and biodiversity in dead wood, as loss of early colonizing beetles may also affect the successional pathways they seem to initiate.

NorWood: a gene expression resource for evo-devo studies of conifer wood development.

Science.gov (United States)

Jokipii-Lukkari, Soile; Sundell, David; Nilsson, Ove; Hvidsten, Torgeir R; Street, Nathaniel R; Tuominen, Hannele

2017-10-01

The secondary xylem of conifers is composed mainly of tracheids that differ anatomically and chemically from angiosperm xylem cells. There is currently no high-spatial-resolution data available profiling gene expression during wood formation for any coniferous species, which limits insight into tracheid development. RNA-sequencing data from replicated, high-spatial-resolution section series throughout the cambial and woody tissues of Picea abies were used to generate the NorWood.conGenIE.org web resource, which facilitates exploration of the associated gene expression profiles and co-expression networks. Integration within PlantGenIE.org enabled a comparative regulomics analysis, revealing divergent co-expression networks between P. abies and the two angiosperm species Arabidopsis thaliana and Populus tremula for the secondary cell wall (SCW) master regulator NAC Class IIB transcription factors. The SCW cellulose synthase genes (CesAs) were located in the neighbourhoods of the NAC factors in A. thaliana and P. tremula, but not in P. abies. The NorWood co-expression network enabled identification of potential SCW CesA regulators in P. abies. The NorWood web resource represents a powerful community tool for generating evo-devo insights into the divergence of wood formation between angiosperms and gymnosperms and for advancing understanding of the regulation of wood development in P. abies. © 2017 The Authors. New Phytologist © 2017 New Phytologist Trust.

Manufacturing of a REBCO racetrack coil using thermoplastic resin aiming at Maglev application

Science.gov (United States)

Mizuno, Katsutoshi; Ogata, Masafumi; Hasegawa, Hitoshi

2015-11-01

The REBCO coated conductor is a promising technology for the Maglev application in terms of its high critical temperature. The operating temperature of the on-board magnets can be around 40-50 K with the coated conductor. The REBCO coils are cooled by cryocoolers directly, and hence the thermal design of the REBCO coils significantly changes from that of LTS coils. We have developed a novel REBCO coil structure using thermoplastic resin. The coil is not impregnated and the thermoplastic resin is used to bond the coil winding and the heat transfer members, e.g. copper and aluminum plates. The viscosity of the thermoplastic resin is high enough for the thermoplastic resin not to permeate between the turns in the coil. Therefore, the thermal stress does not occur and the risk of degradation is removed. This paper contains the following three topics. First, the thermal resistance of the thermoplastic resin was measured at cryogenic temperature. Then, a small round REBCO coil was experimentally produced. It has been confirmed that the thermoplastic resin does not cause the degradation and, the adhesion between the coil winding and copper plates withstands the thermal stress. Finally, we successfully produced a full-scale racetrack REBCO coil applying the coil structure with the thermoplastic resin.

Continuous Natural Fiber Reinforced Thermoplastic Composites by Fiber Surface Modification

Directory of Open Access Journals (Sweden)

Patcharat Wongsriraksa

2013-01-01

Full Text Available Continuous natural fiber reinforced thermoplastic materials are expected to replace inorganic fiber reinforced thermosetting materials. However, in the process of fabricating the composite, it is difficult to impregnate the thermoplastic resin into reinforcement fiber because of the high melt viscosity. Therefore, intermediate material, which allows high impregnation during molding, has been investigated for fabricating continuous fiber reinforced thermoplastic composite by aligning resin fiber alongside reinforcing fiber with braiding technique. This intermediate material has been called “microbraid yarn (MBY.” Moreover, it is well known that the interfacial properties between natural fiber and resin are low; therefore, surface treatment on continuous natural fiber was performed by using polyurethane (PU and flexible epoxy (FLEX to improve the interfacial properties. The effect of surface treatment on the mechanical properties of continuous natural fiber reinforced thermoplastic composites was examined. From these results, it was suggested that surface treatment by PU with low content could produce composites with better mechanical properties.

Transplantation of subalpine wood-pasture turfs along a natural climatic gradient reveals lower resistance of unwooded pastures to climate change compared to wooded ones.

Science.gov (United States)

Gavazov, Konstantin; Spiegelberger, Thomas; Buttler, Alexandre

2014-04-01

Climate change could impact strongly on cold-adapted mountain ecosystems, but little is known about its interaction with traditional land-use practices. We used an altitudinal gradient to simulate a year-round warmer and drier climate for semi-natural subalpine grasslands across a landscape of contrasting land-use management. Turf mesocosms from three pasture-woodland land-use types-unwooded pasture, sparsely wooded pasture, and densely wooded pasture-spanning a gradient from high to low management intensity were transplanted downslope to test their resistance to two intensities of climate change. We found strong overall effects of intensive (+4 K) experimental climate change (i.e., warming and reduced precipitation) on plant community structure and function, while moderate (+2 K) climate change did not substantially affect the studied land-use types, thus indicating an ecosystem response threshold to moderate climate perturbation. The individual land-use types were affected differently under the +4 K scenario, with a 60% decrease in aboveground biomass (AGB) in unwooded pasture turfs, a 40% decrease in sparsely wooded pasture turfs, and none in densely wooded ones. Similarly, unwooded pasture turfs experienced a 30% loss of species, advanced (by 30 days) phenological development, and a mid-season senescence due to drought stress, while no such effects were recorded for the other land-use types. The observed contrasting effects of climate change across the pasture-woodland landscape have important implications for future decades. The reduced impact of climate change on wooded pastures as compared to unwooded ones should promote the sustainable land use of wooded pastures by maintaining low management intensity and a sparse forest canopy, which buffer the immediate impacts of climate change on herbaceous vegetation.

Patterns in hydraulic architecture from roots to branches in six tropical tree species from cacao agroforestry and their relation to wood density and stem growth.

Science.gov (United States)

Kotowska, Martyna M; Hertel, Dietrich; Rajab, Yasmin Abou; Barus, Henry; Schuldt, Bernhard

2015-01-01

For decades it has been assumed that the largest vessels are generally found in roots and that vessel size and corresponding sapwood area-specific hydraulic conductivity are acropetally decreasing toward the distal twigs. However, recent studies from the perhumid tropics revealed a hump-shaped vessel size distribution. Worldwide tropical perhumid forests are extensively replaced by agroforestry systems often using introduced species of various biogeographical and climatic origins. Nonetheless, it is unknown so far what kind of hydraulic architectural patterns are developed in those agroforestry tree species and which impact this exerts regarding important tree functional traits, such as stem growth, hydraulic efficiency and wood density (WD). We investigated wood anatomical and hydraulic properties of the root, stem and branch wood in Theobroma cacao and five common shade tree species in agroforestry systems on Sulawesi (Indonesia); three of these were strictly perhumid tree species, and the other three tree species are tolerating seasonal drought. The overall goal of our study was to relate these properties to stem growth and other tree functional traits such as foliar nitrogen content and sapwood to leaf area ratio. Our results confirmed a hump-shaped vessel size distribution in nearly all species. Drought-adapted species showed divergent patterns of hydraulic conductivity, vessel density, and relative vessel lumen area between root, stem and branch wood compared to wet forest species. Confirming findings from natural old-growth forests in the same region, WD showed no relationship to specific conductivity. Overall, aboveground growth performance was better predicted by specific hydraulic conductivity than by foliar traits and WD. Our study results suggest that future research on conceptual trade-offs of tree hydraulic architecture should consider biogeographical patterns underlining the importance of anatomical adaptation mechanisms to environment.

The effects of habitat degradation on metacommunity structure of wood-inhabiting fungi in European beech forests

DEFF Research Database (Denmark)

Halme, Panu; Ódor, Péter; Christensen, Morten

2013-01-01

Intensive forest management creates habitat degradation by reducing the variation of forest stands in general, and by removing old trees and dead wood in particular. Non-intervention forest reserves are commonly believed to be the most efficient tool to counteract the negative effects...... with different management histories. For this purpose, we used a large data set of wood-inhabiting fungi collected from dead beech trees in European beech-dominated forest reserves. The structure of fungal assemblages showed high beta diversity, while nestedness and similarity was low. During the decomposition...... extirpated specialized species from the local species pools in managed sites, and resulted in more homogeneous communities in managed sites. It is alarming that community structure is affected the most in the latest decay stages where the decay process turns the dead wood into litter, and which is thus...

Influence of gamma irradiation in the thermoplastic elastomer (TPE)

International Nuclear Information System (INIS)

Oliveira, Camila B.; Parra, Duclerc F.; Marchini, Leonardo G.

2017-01-01

The TPE is the nomenclature used for the thermoplastic elastomer, which is also known as thermoplastic rubber. It belongs to an under-researched class of engineering plastics, however, in recent years there has been steady growth due to its important and unusual combination of properties. During its use, it behaves like an elastomer, but, unlike traditional elastomers (vulcanized rubbers), it can be processed using conventional technologies and equipment used for thermoplastics, such as extrusion and injection. The processing of polymers, such as TPE by means of radiation, constitutes a technological area dedicated to the study of the physical and chemical effects caused by high energy radiation, such as gamma radiation. Thus the objective of this work is to evaluate the mechanical and thermal properties of TPE irradiated by 60 Co source of gamma radiation in different doses. The thermoplastic elastomer being modified by means of ionizing radiation at doses of 5, 10, 20, 30, 50 and 100 kGy the effects of the radiation on the mechanical and thermal properties of this material are evaluated through the tests of tensile tests, TGA, FTIR and Fluency Index

WGDB: Wood Gene Database with search interface.

Science.gov (United States)

Goyal, Neha; Ginwal, H S

2014-01-01

Wood quality can be defined in terms of particular end use with the involvement of several traits. Over the last fifteen years researchers have assessed the wood quality traits in forest trees. The wood quality was categorized as: cell wall biochemical traits, fibre properties include the microfibril angle, density and stiffness in loblolly pine [1]. The user friendly and an open-access database has been developed named Wood Gene Database (WGDB) for describing the wood genes along the information of protein and published research articles. It contains 720 wood genes from species namely Pinus, Deodar, fast growing trees namely Poplar, Eucalyptus. WGDB designed to encompass the majority of publicly accessible genes codes for cellulose, hemicellulose and lignin in tree species which are responsive to wood formation and quality. It is an interactive platform for collecting, managing and searching the specific wood genes; it also enables the data mining relate to the genomic information specifically in Arabidopsis thaliana, Populus trichocarpa, Eucalyptus grandis, Pinus taeda, Pinus radiata, Cedrus deodara, Cedrus atlantica. For user convenience, this database is cross linked with public databases namely NCBI, EMBL & Dendrome with the search engine Google for making it more informative and provides bioinformatics tools named BLAST,COBALT. The database is freely available on www.wgdb.in.

High performance thermoplastics: A review of neat resin and composite properties

Science.gov (United States)

Johnston, Norman J.; Hergenrother, Paul M.

1987-01-01

A review was made of the principal thermoplastics used to fabricate high performance composites. Neat resin tensile and fracture toughness properties, glass transition temperatures (Tg), crystalline melt temperatures (Tm) and approximate processing conditions are presented. Mechanical properties of carbon fiber composites made from many of these thermoplastics are given, including flexural, longitudinal tensile, transverse tensile and in-plane shear properties as well as short beam shear and compressive strengths and interlaminar fracture toughness. Attractive features and problems involved in the use of thermo-plastics as matrices for high performance composites are discussed.

Construction of Hydrophobic Wood Surface and Mechanical Property of Wood Cell Wall on Nanoscale Modified by Dimethyldichlorosilane

Science.gov (United States)

Yang, Rui; Wang, Siqun; Zhou, Dingguo; Zhang, Jie; Lan, Ping; Jia, Chong

2018-01-01

Dimethyldichlorosilane was used to improve the hydrophobicity of wood surface. The water contact angle of the treated wood surface increased from 85° to 143°, which indicated increased hydrophobicity. The nanomechanical properties of the wood cell wall were evaluated using a nanoindentation test to analyse the hydrophobic mechanism on the nano scale. The elastic modulus of the cell wall was significantly affected by the concentration but the influence of treatment time is insignificant. The hardness of the cell wall for treated samples was significantly affected by both treatment time and concentration. The interaction between treatment time and concentration was extremely significant for the elastic modulus of the wood cell wall.

Investigation on the Scratch Strength of Clear Paints Used in Furniture Industries on the Wood Species Beech, Elm, Alder and Spruce

Directory of Open Access Journals (Sweden)

Mohammad Ghofrani

2014-05-01

Full Text Available In This research, the scratch strength (Cross-Cut Test of clear paints (nitrocellulose lacquers and acid catalyst lacquers of wood species Beech, Elm, Alder and spruce were studied as a function of moisture content (MC of the samples. For this purpose, lumbers (550×110×12 mm were cut from sapwood in tangential surfaces and were air dried for one month according to wood drying procedures. Then, for pre-conditioning of moisture content, at the levels of 8%, 12% and 15%, the samples were placed in three clima rooms. Then, finish applied and strength tests were performed. The results revealed that for acid catalyst lacquers the highest scratch strength (10.4% belongs to Elm wood with 8% moisture content, and the lowest scratch strength (53.6% belongs to Spruce wood with nitrocellulose lacquers having 15% moisture content.

Variation of moisture content of some varnished woods in indoor climatic conditions

Directory of Open Access Journals (Sweden)

Kemal Üçüncü

2017-11-01

Full Text Available In this study, moisture change of varnished wood of black poplar (Populus nigra and yellow pine (Pinus silvestris L. used in indoor climate conditions with central heating in Trabzon (Turkey were investigated. 300 mm length wood specimens, with cross section of 12.5 mm in tangential and in radial and with the square sections of 25mm and 50 mm, were obtained from two species grown in Kanuni Campus of the Karadeniz Technical University. In this research, un-varnished wood samples were also used for reference. The wood moisture content was determined by the weighing method, the wood equilibrium moisture content by the Hailwood-Horrobin equation, and the relative humidity in the indoor climatic conditions by humid air thermodynamic principles. As a result; it was observed that the moisture content of varnished wood samples has a strong relationship with equilibrium moisture content, temperature and relative humidity. It was found that the moisture content of varnished woods was higher than the moisture content of un-varnished woods in the same climatic conditions. It was observed that the difference between the monthly average moisture content was lower in varnished woods in proportion to un-varnished woods. According to these results, it can be indicated that it would be more appropriate to select higher moisture content in the drying of wood than the equilibrium moisture content. Such an application would also reduce drying costs. Further, it can be recommended to use varnished wood in various applications because the low change range of average moisture content can affect the swelling or shrinking of wood.

Interactions between soil- and dead wood-inhabiting fungal communities during the decay of Norway spruce logs.

Science.gov (United States)

Mäkipää, Raisa; Rajala, Tiina; Schigel, Dmitry; Rinne, Katja T; Pennanen, Taina; Abrego, Nerea; Ovaskainen, Otso

2017-09-01

We investigated the interaction between fungal communities of soil and dead wood substrates. For this, we applied molecular species identification and stable isotope tracking to both soil and decaying wood in an unmanaged boreal Norway spruce-dominated stand. Altogether, we recorded 1990 operational taxonomic units, out of which more than 600 were shared by both substrates and 589 were found to exclusively inhabit wood. On average the soil was more species-rich than the decaying wood, but the species richness in dead wood increased monotonically along the decay gradient, reaching the same species richness and community composition as soil in the late stages. Decaying logs at all decay stages locally influenced the fungal communities from soil, some fungal species occurring in soil only under decaying wood. Stable isotope analyses suggest that mycorrhizal species colonising dead wood in the late decay stages actively transfer nitrogen and carbon between soil and host plants. Most importantly, Piloderma sphaerosporum and Tylospora sp. mycorrhizal species were highly abundant in decayed wood. Soil- and wood-inhabiting fungal communities interact at all decay phases of wood that has important implications in fungal community dynamics and thus nutrient transportation.

Wood anatomical characteristics of Durio Adans. (malvaceae - helicteroideae: Durioneae)

Science.gov (United States)

Nordahlia, A. S.; Noraini, T.; Chung, R. C. K.; Nadiah, I.; Lim, S. C.; Norazahana, A.; Noorsolihani, S.

2016-11-01

A wood anatomy study was carried out on 10 Durio species. Three species, namely D. griffithii, D. grandiflorus and D. excelsus were included, and these species were previously placed in the genus Boschia. Findings have shown presence of prismatic crystals in chambered and non-chambered axial parenchyma in seven Durio species studied, whilst silica was absent. However, in the other three species (D. griffithii, D. grandiflorus and D. excelsus) silica was present, whilst crystal was absent. The presence of this mineral inclusion in these three species was not good taxonomic character at generic level and cannot be used to distinguish Boschia from Durio. Therefore, Durio is suggested to be maintained based on findings in this study. There is no diagnostic wood anatomical characteristic that can be used to differentiate species in Durio. As a conclusion the wood anatomy alone does not aid in delimiting species in Durio.

Wood identification of Dalbergia nigra (CITES Appendix I) using quantitative wood anatomy, principal components analysis and naive Bayes classification.

Science.gov (United States)

Gasson, Peter; Miller, Regis; Stekel, Dov J; Whinder, Frances; Zieminska, Kasia

2010-01-01

Dalbergia nigra is one of the most valuable timber species of its genus, having been traded for over 300 years. Due to over-exploitation it is facing extinction and trade has been banned under CITES Appendix I since 1992. Current methods, primarily comparative wood anatomy, are inadequate for conclusive species identification. This study aims to find a set of anatomical characters that distinguish the wood of D. nigra from other commercially important species of Dalbergia from Latin America. Qualitative and quantitative wood anatomy, principal components analysis and naïve Bayes classification were conducted on 43 specimens of Dalbergia, eight D. nigra and 35 from six other Latin American species. Dalbergia cearensis and D. miscolobium can be distinguished from D. nigra on the basis of vessel frequency for the former, and ray frequency for the latter. Principal components analysis was unable to provide any further basis for separating the species. Naïve Bayes classification using the four characters: minimum vessel diameter; frequency of solitary vessels; mean ray width; and frequency of axially fused rays, classified all eight D. nigra correctly with no false negatives, but there was a false positive rate of 36.36 %. Wood anatomy alone cannot distinguish D. nigra from all other commercially important Dalbergia species likely to be encountered by customs officials, but can be used to reduce the number of specimens that would need further study.

Determination of pectin content of eucalyptus wood

NARCIS (Netherlands)

Coetzee, B.; Schols, H.A.; Wolfaardt, F.

2011-01-01

Very little is known about the occurrence of pectin in wood and it is speculated that between 10 mg g-1 and 40 mg g-1 of wood consists of pectin. The present study aimed to quantify pectin in eucalyptus wood and to determine the influence of tree species, yield potential of the site, tree age class

Assessment of local wood species used for the manufacture of cookware and the perception of chemical benefits and chemical hazards associated with their use in Kumasi, Ghana

Directory of Open Access Journals (Sweden)

Mensah John Kenneth

2012-12-01

Full Text Available Abstract Background Historical proven wood species have no reported adverse health effect associated with its past use. Different historical proven species have traditionally been used to manufacture different wooden food contact items. This study uses survey questionnaires to assess suppliers’, manufacturers’, retailers’ and consumers’ (end-users’ preferences for specific wood species, to examine the considerations that inform these preferences and to investigate the extent of awareness of the chemical benefits and chemical hazards associated with wooden food contact material use. Methods Through the combined use of a cross sectional approach and a case study design, 25 suppliers, 25 manufacturers, 25 retailers and 125 consumers (end-users of wooden food contact materials in four suburbs in Kumasi Metropolitan Area (Anloga junction, Ahinsan Bus Stop, Ahwia-Pankrono and Race Course and Ashanti Akyim Agogo in the Ashanti Akyim North District of the Ashanti Region were administered with closed ended questionnaires. The questionnaires were prepared in English, but local language, Twi, was used to translate and communicate the content of the questionnaire where necessary. Results Suppliers’, manufacturers’ and retailers’ preferences for specific wood species for most wooden cookware differed from that of consumers (end-users. But all respondent groups failed to indicate any awareness of chemical benefits or chemical hazards associated with either the choice of specific wood species for specific wooden cookware or with the general use of wooden food contact materials. The lack of appreciation of chemical benefits or hazards associated with active principles of wooden cookware led to heavy reliance of consumers (end-users on the wood density, price, attractive grain pattern and colour or on the judgement of retailers in their choice of specific species for a wooden cookware. Conclusion This study contributes some practical suggestions

Aureobasidium melanogenum: a native of dark biofinishes on oil treated wood.

Science.gov (United States)

van Nieuwenhuijzen, Elke J; Houbraken, Jos A M P; Meijer, Martin; Adan, Olaf C G; Samson, Robert A

2016-05-01

The genus Aureobasidium, which is known as a wood staining mould, has been detected on oil treated woods in the specific stain formation called biofinish. This biofinish is used to develop a new protective, self-healing and decorative biotreatment for wood. In order to understand and control biofinish formation on oil treated wood, the occurrence of different Aureobasidium species on various wood surfaces was studied. Phenotypic variability within Aureobasidium strains presented limitations of morphological identification of Aureobasidium species. PCR amplification and Sanger sequencing of ITS and RPB2 were used to identify the culturable Aureobasidium species composition in mould stained wood surfaces with and without a biofinish. The analysed isolates showed that several Aureobasidium species were present and that Aureobasidium melanogenum was predominantly detected, regardless of the presence of a biofinish and the type of substrate. A. melanogenum was detected on wood samples exposed in the Netherlands, Cameroon, South Africa, Australia and Norway. ITS-specific PCR amplification, cloning and sequencing of DNA extracted from biofinish samples confirmed results of the culturing based method: A. melanogenum is predominant within the Aureobasidium population of biofinishes on pine sapwood treated with raw linseed oil and the outdoor placement in the Netherlands.

Method for bonding a thermoplastic polymer to a thermosetting polymer component

NARCIS (Netherlands)

Van Tooren, M.J.L.

2012-01-01

The invention relates to a method for bonding a thermoplastic polymer to a thermosetting polymer component, the thermoplastic polymer having a melting temperature that exceeds the curing temperature of the thermosetting polymer. The method comprises the steps of providing a cured thermosetting

THE EFFECT OF GRAIN ANGLE AND SPECIES ON THERMAL CONDUCTIVITY OF SOME SELECTED WOOD SPECIES

Directory of Open Access Journals (Sweden)

Rasit Esen

2011-06-01

Full Text Available In this study the thermal conductivity of different wood materials was determined. For this purpose, Scots pine (Pinus sylvestris L., Uludag fir (Abies Bornmülleriana Matff, Oriental beech (Fagus orientalis L, Oak (Quercus robur L., and Chestnut of Anatolia (Castanea sativa Mill. woods were used. In the test, the thermal conductivity of the woods was measured according to procedure of ASTM C 1113-99 standards. The lowest thermal conductivity was obtained in the perpendicular direction of Scots pine samples as 0.156 Kcal/mh°C. The highest thermal conductivity was obtained from perpendicular direction of samples in Oriental beech as 0.331 Kcal/mh°C.

Thermoforming of Continuous Fibre Reinforced Thermoplastic Composites

International Nuclear Information System (INIS)

McCool, Rauri; Murphy, Adrian; Wilson, Ryan; Jiang Zhenyu; Price, Mark

2011-01-01

The introduction of new materials, particularly for aerospace products, is not a simple, quick or cheap task. New materials require extensive and expensive qualification and must meet challenging strength, stiffness, durability, manufacturing, inspection and maintenance requirements. Growth in industry acceptance for fibre reinforced thermoplastic composite systems requires the determination of whole life attributes including both part processing and processed part performance data. For thermoplastic composite materials the interactions between the processing parameters, in-service structural performance and end of life recyclability are potentially interrelated. Given the large number and range of parameters and the complexity of the potential relationships, understanding for whole life design must be developed in a systematic building block approach. To assess and demonstrate such an approach this article documents initial coupon level thermoforming trials for a commercially available fibre reinforced thermoplastic laminate, identifying the key interactions between processing and whole life performance characteristics. To examine the role of the thermoforming process parameters on the whole life performance characteristics of the formed part requires a series of manufacturing trials combined with a series of characterisation tests on the manufacturing trial output. Using a full factorial test programme and considering all possible process parameters over a range of potential magnitudes would result in a very large number of manufacturing trials and accompanying characterisation tests. Such an approach would clearly be expensive and require significant time to complete, therefore failing to address the key requirement for a future design methodology capable of rapidly generating design knowledge for new materials and processes. In this work the role of mould tool temperature and blank forming temperature on the thermoforming of a commercially available

Wood anatomy of the neotropical Sapotaceae : XVII. Gambeya

Science.gov (United States)

Bohumil Francis Kukachka

1980-01-01

Gambeya is an African genus to which Aubréville added Gambeya excelsa (Huber) Aubr., based on the Amazonian Chrysophyllum excelsum Huber. Whether Gambeya is the appropriate taxon for the American species remains to be resolved. Wood specimens indicate that several species occur in the Americas ranging from Southern Mexico to the Peruvian Amazon. The woods of the...

Measuring wood specific gravity, correctly

Science.gov (United States)

G. Bruce Williamson; Michael C. Wiemann

2010-01-01

The specific gravity (SG) of wood is a measure of the amount of structural material a tree species allocates to support and strength. In recent years, wood specific gravity, traditionally a forester’s variable, has become the domain of ecologists exploring the universality of plant functional traits and conservationists estimating global carbon stocks. While these...

Factors affecting distribution of wood, detritus, and sediment in headwater streams draining managed young-growth red alder - Conifer forests in southeast Alaska

Science.gov (United States)

Gomi, T.; Johnson, A.C.; Deal, R.L.; Hennon, P.E.; Orlikowska, E.H.; Wipfli, M.S.

2006-01-01

Factors (riparian stand condition, management regimes, and channel properties) affecting distributions of wood, detritus (leaves and branches), and sediment were examined in headwater streams draining young-growth red alder (Alnus rubra Bong.) - conifer riparian forests (40 years old) remained in channels and provided sites for sediment and organic matter storage. Despite various alder-conifer mixtures and past harvesting effects, the abundance of large wood, fine wood, and detritus accumulations significantly decreased with increasing channel bank-full width (0.5-3.5 m) along relatively short channel distances (up to 700 m). Changes in wood, detritus, and sediment accumulations together with changes in riparian stand characteristics create spatial and temporal variability of in-channel conditions in headwater systems. A component of alder within young-growth riparian forests may benefit both wood production and biological recovery in disturbed headwater stream channels. ?? 2006 NRC.

Thermoplastic liners for carbon steel pipelines

Energy Technology Data Exchange (ETDEWEB)

Mehdi, Mauyed S.; AlDossary, Abdullah K. [Saudi Aramco, Dhahran (Saudi Arabia)

2009-12-19

Materials selection for pipe and fittings used to convey corrosive fluids has often been a challenge. Traditionally, exotic Corrosion Resistant Alloys (CRA) have been used in corrosive environments despite their high cost. Plastic lined carbon steel piping offers a cost effective alternative to the use of CRAs by eliminating corrosion, significantly reducing the use of toxic chemicals and the heavy metal usually present in CRAs. Thermoplastic Liners offer the combination of corrosion resistance and mechanical strength, which are unachievable with singular materials. Under pressure conditions, the liner is fully supported by the metalwork, while under vacuum conditions, the liner must be thick enough along with venting system to withstand the collapsing forces created by the negative pressure. Plastic liners have been used successfully to line and protect metallic pipelines for many years and have become an indispensable requirement of the oil and gas industry particularly with water injection and hydrocarbon services. In the case of internally corroded pipes, the use of thermoplastic liners for rehabilitation is an option to extend the lifetime of companies' assets, reduce maintenance cost and increase intervals between T and Is. For new construction, plastic liners in carbon steel pipes can compete technically and economically with pipelines of CRA materials and other corrosion inhibition systems. This paper describes various design features, installations of thermoplastic liners in comparison to other corrosion inhibition methods. (author)

Systematic wood anatomy of the Rosaceae

NARCIS (Netherlands)

Zhang, Shu-Yin

1992-01-01

The wood anatomy of the Rosaceae is surveyed and analysed, based on the study of 280 species (c. 500 specimens) belonging to 62 genera from different parts of the world. Eighteen wood anatomical characters have been used for a phenetic and phylogenetic classification. In the phenetic classification,

The Effects of Aluminium Hydroxide and Magnesium Hydroxide on the Mechanical Properties of Thermoplastic Polyurethane Materials

Directory of Open Access Journals (Sweden)

Erkin Akdoğan

2015-12-01

Full Text Available Thermoplastic polyurethane materials are widely used in automotive, clothing, electrical and electronics, medical, construction, machine industry due to excellent physical and chemical properties. Thermoplastic polyurethane materials combustion and resistance to high temperature characteristics are poor. Additives and fillers are added into the polyurethane matrix to improve those properties. Particularly adding these agents as a flame retardant are affect mechanical properties of polyurethane materials. Therefore, it is important to determinate the mechanical properties of these materials. In this study, 5% by weight of the thermoplastic polyurethane material, aluminium tri hydroxide (ATH, (Al2O3 3H2O and magnesium hydroxide (MgOH, (Mg(OH2 were added. Ammonium polyphosphate (APP as an intumescent flame retardant with inorganic flame retardants were added to increase the flame resistance of produced composite structure. Tensile test, tear test, hardness and Izod impact tests were made and compared of those produced composites. As a result of experiments the addition of ATH has lowered the tensile strength and tear strength contrast to this the addition of MgOH has improved those properties. Hardness and Izod impact test results were showed that both of the additives have no negative effect.

Thermoplastic elastomers containing 2D nanofillers: montmorillonite, graphene nanoplatelets and oxidized graphene platelets

OpenAIRE

Paszkiewicz Sandra; Pawelec Iwona; Szymczyk Anna; Rosłaniec Zbigniew

2015-01-01

This paper presents a comparative study on which type of platelets nanofiller, organic or inorganic, will affect the properties of thermoplastic elastomer matrix in the stronger manner. Therefore, poly(trimethylene terephthalate-block-poly(tetramethylene oxide) copolymer (PTT-PTMO) based nanocomposites with 0.5 wt.% of clay (MMT), graphene nanoplatelets (GNP) and graphene oxide (GO) have been prepared by in situ polymerization. The structure of the nanocomposites was characterized by transmis...

Large wood budget assessment along a gravel bed river affected by volcanic eruption: the Rio Blanco study case (Chile).

Science.gov (United States)

Oss-Cazzador, Daniele; Iroume, Andres; Lenzi, Mario; Picco, Lorenzo

2016-04-01

Wood in riverine environments exerts different functions on ecological and geomorphic settings, influencing morphological processes, and increasing risks for sensitive structures. Large wood (LW) is defined as wood material, dead or alive, larger than 10 cm in diameter and 1 m in length. Natural hazards can strongly increase the presence of LW in waterways and flood events can transport it affecting the ecosystem and landscape. This study aims to increase the knowledge of wood budget, considering the effects of two subsequent slight flood events along a sub-reach of the Rio Blanco gravel bed river , in Chilean Patagonia, strongly affected by the eruption of Chaiten volcano in 2008. The volcanic eruption affected almost 3,5 km 2 of evergreen forest on the southern (left) bank, because of primary direct effects from pyroclastic density currents and lahar-floods that caused deposition up to 8 m of reworked tephra, alluvium, and wood on floodplains and terrace along the Rio Blanco. After the eruption, there was a considerable increase of LW into the main channel: into the bankfull channel, volume exceeds 100 m 3 /ha. Field surveys were carried out in January and March 2015, before and after two slight flood events (Recurrence Intervals lower than 1 year). The pre-event phase permitted to detect and analyze the presence of LW into the study area, along a 80 m-long reach of Rio Blanco (7500 m 2 . Every LW element was manually measured and described, a numbered metal tag was installed, and the position was recorded by GPS device. In January, there was a total amount of 113 m 3 /ha, 90% accumulated in LW jams (WJ) and 10% as single logs. The LW was characterized by mean dimensions of 3,36 m height, 0,25 m diameter and 0,26 m 3 volume, respectively. The WJ are characterized by wide range of dimension: volume varies from 0,28 m 3 to 672 m 3 , length from 1,20 m to 56 m, width from 0,40 m to 8,70 m and height from 0,20 m to 3 m, respectively. After the flood events, field

Evaluation of wood species and preservatives for WisDOT sign posts.

Science.gov (United States)

2013-10-01

The Wisconsin Department of Transportation (WisDOT) uses preservative-treated wood posts for much of the signage along state highways because wood is relatively inexpensive, easy to install, and has the necessary strength properties to tolerate typic...

Characteristics and utilization of thermoplastic elastomers (TPE)-an overview

Energy Technology Data Exchange (ETDEWEB)

Roestamsjah, [R and D Center for Applied Chemistry, Indonesian Inst. of Sciences (Indonesia)

1998-10-01

The unique feature of thermoplastic elastomer, the combining of processing characteristics of thermoplastics with the physical properties of vulcanized rubber is reviewed. Highlights of TPE and its characteristics is aimed to generate interest in TPE, where SANS technique will be utilized for its characterization. The topics discussed include rubber elasticity, state of aggregation of polymers, microseparation in block copolymer system, application of TPE, and finally some notes in developing interest in TPE and SANS in Indonesia. (author)

Adaptability to climate change in forestry species: drought effects on growth and wood anatomy of ponderosa pines growing at different competition levels

OpenAIRE

Fernández, M.E.; Gyenge, J.E.; de Urquiza, M.M.; Varela, S.

2012-01-01

More stressful conditions are expected due to climatic change in several regions, including Patagonia, South-America. In this region, there are no studies about the impact of severe drought events on growth and wood characteristics of the most planted forestry species, Pinus ponderosa (Doug. ex-Laws). The objective of this study was to quantify the effect of a severe drought event on annual stem growth and functional wood anatomy of pines growing at different plantation densities aiming to un...

Northward invading non-native vascular plant species in and adjacent to Wood Buffalo National Park

Energy Technology Data Exchange (ETDEWEB)

Wein, R.W.; Wein, G.; Bahret, S.; Cody, W.J. (Alberta University, Edmonton, AB (Canada). Canadian Circumpolar Institute)

A survey of the non-native vascular plant species in Wood Buffalo National Park, Canada's largest forested National Park, documented their presence and abundance in key locations. Most of the fifty-four species (nine new records) were found in disturbed sites including roadsides, settlements, farms, areas of altered hydrological regimes, recent bums, and intensive bison grazing. Species that have increased most in geographic area and abundance in recent years include [ital Agropyron repens], [ital Bromus inermis], [ital Chenopodium album], [ital Melilotus spp.], [ital Trifolium spp.], [ital Plantago major], [ital Achillea millefolium], [ital Crepis tectorum] and [ital Sonchus arvensis]. An additional 20 species, now common in the Peace River and Fort Vermilion areas, have the potential to invade the Park if plant communities are subjected to additional stress as northern climates are modified by the greenhouse effect and as other human-caused activities disturb the vegetation. It is recommended that permanent plots be located in key locations and monitored for species invasion and changing abundances as input to management plans.

Creep and creep-recovery of a thermoplastic resin and composite

Science.gov (United States)

Hiel, Clem

1988-01-01

The database on advanced thermoplastic composites, which is currently available to industry, contains little data on the creep and viscoelastic behavior. This behavior is nevertheless considered important, particularly for extended-service reliability in structural applications. The creep deformation of a specific thermoplastic resin and composite is reviewed. The problem to relate the data obtained on the resin to the data obtained on the composite is discussed.

Mycosphaerella and Teratosphaeria species associated with Mycosphaerella Leaf Disease on Eucalyptus globulus in Portugal

Energy Technology Data Exchange (ETDEWEB)

Silva, M. C.; Machado, H. N.; Neves, L.; Araujo, C.; Phillips, J. L.

2012-11-01

Plantations of Eucalyptus globulus represent the main source of wood for the pulp and paper industry in Portugal and are affected by the complex of Mycosphaerella and Teratosphaeria species (Mycosphaerella leaf disease), which is an important foliage disease worldwide. This disease affect mainly young trees with juvenile-phase foliage, causing premature defoliation, decreased growth and wood production. Species of Mycosphaerella sensu lato reported on eucalypts in Portugal are M. communis, M. heimii, M. lateralis, M. madeirae, M. marksii M. walkeri, T. africana, T. molleriana, T. nubilosa and T. parva. In order to complete the survey, symptomatic leaves were collected from Eucalyptus globulus plantations. Morphological and molecular characterization was used to give an indication of the species occurrence and most frequent species (T. nubilosa) and the composition of the MLD complex that did not change after the latest review. (Author) 28 refs.

Wood for fuel

Energy Technology Data Exchange (ETDEWEB)

Beaton, D

1986-01-01

Growing wood for energy could contribute three million tonnes of coal equivalent per year by the end of the century. Research programmes in the UK involved with energy forestry are reported. Three systems of wood energy, modified conventional forestry, single stem timber cropping and short rotation coppicing are being investigated. The short rotation coppicing requires inputs similar to those of agricultural crops and the machinery geared towards agricultural operations is compatible with it. Single stem forestry has a medium rotation period of 20 years. The production of coppice wood fuels is discussed in further detail for different parts of the UK with recommendations for species selection and adaption of existing farming practices. A coppice willow harvester has been developed for harvesting during November - February. Weed control and fertilizer application are also briefly mentioned.

Global timber investments, wood costs, regulation, and risk

International Nuclear Information System (INIS)

Cubbage, Frederick; Koesbandana, Sadharga; Gonzalez, Ronalds; Carrero, Omar; MacIntyre, Charles; Abt, Robert; Phillips, Richard; Mac Donagh, Patricio; Rubilar, Rafael; Balmelli, Gustavo; Olmos, Virginia Morales; De La Torre, Rafael; Murara, Mauro; Hoeflich, Vitor Afonso; Kotze, Heynz; Frey, Gregory; Adams, Thomas; Turner, James; Lord, Roger; Huang, Jin; McGinley, Kathleen

2010-01-01

We estimated financial returns and wood production costs in 2008 for the primary timber plantation species. Excluding land costs, returns for exotic plantations in almost all of South America - Brazil, Argentina, Uruguay, Chile, Colombia, Venezuela, and Paraguay - were substantial. Eucalyptus species returns were generally greater than those for Pinus species in each country, with most having Internal Rates of Return (IRRs) of 20% per year or more, as did teak. Pinus species in South America were generally closer to 15%, except in Argentina, where they were 20%. IRRs were less, but still attractive for plantations of coniferous or deciduous species in China, South Africa, New Zealand, Indonesia, and the United States, ranging from 7% to 12%. Costs of wood production at the cost of capital of 8% per year were generally cheapest for countries with high rates of return and for pulpwood fiber production, which would favor vertically integrated firms in Latin America. But wood costs at stumpage market prices were much greater, making net wood costs for open market wood more similar among countries. In the Americas, Chile and Brazil had the most regulatory components of sustainable forest management, followed by Misiones, Argentina and Oregon in the U.S. New Zealand, the United States, and Chile had the best rankings regarding risk from political, commercial, war, or government actions and for the ease of doing business. Conversely, Venezuela, Indonesia, Colombia, and Argentina had high risk ratings, and Brazil, Indonesia, and Venezuela were ranked as more difficult countries for ease of business. (author)

Global timber investments, wood costs, regulation, and risk

Energy Technology Data Exchange (ETDEWEB)

Cubbage, Frederick; Koesbandana, Sadharga; Gonzalez, Ronalds; Carrero, Omar; MacIntyre, Charles; Abt, Robert; Phillips, Richard [Forestry and Environmental Resources, North Carolina State University, Raleigh, NC (United States); Mac Donagh, Patricio [Universidad Nacional de Misiones (UNAM), Lisandro de la Torre s/n, CP 3380, Eldorado, Misiones (Argentina); Rubilar, Rafael [Universidad de Concepcion, Victoria 631, Casilla 160-C - Correo 3, Concepcion (Chile); Balmelli, Gustavo [Instituto Nacional de Investigacion Agropecuria, INIA Tacuarembo, Ruta 5, Km 386, Tacuarembo (Uruguay); Olmos, Virginia Morales [Weyerhaeuser Company, La Rosa 765, Melo (Uruguay); De La Torre, Rafael [CellFor, 247 Davis Street, Athens, GA (United States); Murara, Mauro [Universidade do Contestado, R. Joaquim Nabuco, 314 Bairro Cidade Nova, Porto Uniao, Santa Catarina (Brazil); Hoeflich, Vitor Afonso [Universidade Federal do Parana, Av. Pref. Lothario Meissner, 900, 80210-170, Jardim Botanico, Curitiba, Parana (Brazil); Kotze, Heynz [Komatiland Forests (Pty) Ltd, P.O. Box 14228, Nelspruit (South Africa); Frey, Gregory [World Bank, 1818 H. Street NW, Washington, DC (United States); Adams, Thomas; Turner, James [New Zealand Forest Research Institute Ltd., Scion, 49 Sala St., Rotorua (New Zealand); Lord, Roger [Mason, Bruce, and Girard, Inc., 707 SW Washington St., Portland, Oregon (United States); Huang, Jin [Abt Associates, 4550 Montgomery Avenue, Bethesda, MD (United States); McGinley, Kathleen [International Institute of Tropical Forestry, USDA Forest Service, c/o 920 Main Campus Dr. Suite 300, Raleigh, NC (United States)

2010-12-15

We estimated financial returns and wood production costs in 2008 for the primary timber plantation species. Excluding land costs, returns for exotic plantations in almost all of South America - Brazil, Argentina, Uruguay, Chile, Colombia, Venezuela, and Paraguay - were substantial. Eucalyptus species returns were generally greater than those for Pinus species in each country, with most having Internal Rates of Return (IRRs) of 20% per year or more, as did teak. Pinus species in South America were generally closer to 15%, except in Argentina, where they were 20%. IRRs were less, but still attractive for plantations of coniferous or deciduous species in China, South Africa, New Zealand, Indonesia, and the United States, ranging from 7% to 12%. Costs of wood production at the cost of capital of 8% per year were generally cheapest for countries with high rates of return and for pulpwood fiber production, which would favor vertically integrated firms in Latin America. But wood costs at stumpage market prices were much greater, making net wood costs for open market wood more similar among countries. In the Americas, Chile and Brazil had the most regulatory components of sustainable forest management, followed by Misiones, Argentina and Oregon in the U.S. New Zealand, the United States, and Chile had the best rankings regarding risk from political, commercial, war, or government actions and for the ease of doing business. Conversely, Venezuela, Indonesia, Colombia, and Argentina had high risk ratings, and Brazil, Indonesia, and Venezuela were ranked as more difficult countries for ease of business. (author)

Bacterial Community Succession in Pine-Wood Decomposition.

Science.gov (United States)

Kielak, Anna M; Scheublin, Tanja R; Mendes, Lucas W; van Veen, Johannes A; Kuramae, Eiko E

2016-01-01

Though bacteria and fungi are common inhabitants of decaying wood, little is known about the relationship between bacterial and fungal community dynamics during natural wood decay. Based on previous studies involving inoculated wood blocks, strong fungal selection on bacteria abundance and community composition was expected to occur during natural wood decay. Here, we focused on bacterial and fungal community compositions in pine wood samples collected from dead trees in different stages of decomposition. We showed that bacterial communities undergo less drastic changes than fungal communities during wood decay. Furthermore, we found that bacterial community assembly was a stochastic process at initial stage of wood decay and became more deterministic in later stages, likely due to environmental factors. Moreover, composition of bacterial communities did not respond to the changes in the major fungal species present in the wood but rather to the stage of decay reflected by the wood density. We concluded that the shifts in the bacterial communities were a result of the changes in wood properties during decomposition and largely independent of the composition of the wood-decaying fungal communities.

Composite structure of wood cells in petrified wood

International Nuclear Information System (INIS)

Nowak, Jakub; Florek, Marek; Kwiatek, Wojciech; Lekki, Janusz; Chevallier, Pierre; Zieba, Emil; Mestres, Narcis; Dutkiewicz, E.M.; Kuczumow, Andrzej

2005-01-01

Special kinds of petrified wood of complex structure were investigated. All the samples were composed of at least two different inorganic substances. The original cell structure was preserved in each case. The remnants of the original biological material were detected in some locations, especially in the cell walls. The complex inorganic structure was superimposed on the remnant organic network. The first inorganic component was located in the lumena (l.) of the cells while another one in the walls (w.) of the cells. The investigated arrangements were as follows: calcite (l.)-goethite-hematite (w.)-wood from Dunarobba, Italy; pyrite (l.)-calcite (w.)-wood from Lukow, Poland; goethite (l.)-silica (w.)-wood from Kwaczala, Poland. The inorganic composition was analysed and spatially located by the use of three spectral methods: electron microprobe, X-ray synchrotron-based microprobe, μ-PIXE microprobe. The accurate mappings presenting 2D distribution of the chemical species were presented for each case. Trace elements were detected and correlated with the distribution of the main elements. In addition, the identification of phases was done by the use of μ-Raman and μ-XRD techniques for selected and representative points. The possible mechanisms of the described arrangements are considered. The potential synthesis of similar structures and their possible applications are suggested

Composite structure of wood cells in petrified wood

Energy Technology Data Exchange (ETDEWEB)

Nowak, Jakub [Department of Chemistry, Catholic University of Lublin, 20-718 Lublin (Poland); Florek, Marek [Department of Chemistry, Catholic University of Lublin, 20-718 Lublin (Poland); Kwiatek, Wojciech [Institute of Nuclear Physics, Department of Nuclear Spectroscopy, 31-342 Cracow (Poland); Lekki, Janusz [Institute of Nuclear Physics, Department of Nuclear Spectroscopy, 31-342 Cracow (Poland); Chevallier, Pierre [LPS, CEN Saclay et LURE, Universite Paris-Sud, Bat 209D, F-91405 Orsay (France); Zieba, Emil [Department of Chemistry, Catholic University of Lublin, 20-718 Lublin (Poland); Mestres, Narcis [Institut de Ciencia de Materials de Barcelona (ICMAB), Campus de la UAB, E-08193-Bellaterra (Spain); Dutkiewicz, E.M. [Institute of Nuclear Physics, Department of Nuclear Spectroscopy, 31-342 Cracow (Poland); Kuczumow, Andrzej [Department of Chemistry, Catholic University of Lublin, 20-718 Lublin (Poland)

2005-04-28

Special kinds of petrified wood of complex structure were investigated. All the samples were composed of at least two different inorganic substances. The original cell structure was preserved in each case. The remnants of the original biological material were detected in some locations, especially in the cell walls. The complex inorganic structure was superimposed on the remnant organic network. The first inorganic component was located in the lumena (l.) of the cells while another one in the walls (w.) of the cells. The investigated arrangements were as follows: calcite (l.)-goethite-hematite (w.)-wood from Dunarobba, Italy; pyrite (l.)-calcite (w.)-wood from Lukow, Poland; goethite (l.)-silica (w.)-wood from Kwaczala, Poland. The inorganic composition was analysed and spatially located by the use of three spectral methods: electron microprobe, X-ray synchrotron-based microprobe, {mu}-PIXE microprobe. The accurate mappings presenting 2D distribution of the chemical species were presented for each case. Trace elements were detected and correlated with the distribution of the main elements. In addition, the identification of phases was done by the use of {mu}-Raman and {mu}-XRD techniques for selected and representative points. The possible mechanisms of the described arrangements are considered. The potential synthesis of similar structures and their possible applications are suggested.

Reactivity and burnout of wood fuels

DEFF Research Database (Denmark)

Dall'Ora, Michelangelo

This thesis deals with the combustion of wood in pulverised fuel power plants. In this type of boiler, the slowest step in the wood conversion process is char combustion, which is one of the factors that not only determine the degree of fuel burnout, but also affect the heat release profile...... of different aspects relevant to wood combustion, including wood structure and composition, wood pyrolysis, wood char properties and wood char oxidation. The full scale campaign, which is the subject of Chapter 3, included sampling of wood fuel before and after milling and sampling of gas and particles...... at the top of the combustion chamber. The collected samples and data are used to obtain an evaluation of the mills in operation at the power plant, the particle size distribution of the wood fuel, as well as the char conversion attained in the furnace. In Chapter 4 an experimental investigation...

Interspecific interactions between wood-inhabiting basidiomycetes in boreal forests

Energy Technology Data Exchange (ETDEWEB)

Holmer, L.

1996-05-01

Studies of competition and succession in communities of wood-decomposing fungi were carried out using laboratory tests with different approaches. Based on results of these tests, an attempt to biologically control Heterobasidion annosum was made in field. Competitive interactions between six species of wood decay fungi were studied using a system of preinoculated wood blocks in unsterilized soil. Two of the species were root-rotting pathogens with a primary resource capture strategy, and four were primarily saprotrophic cord-forming species assumed to use secondary resource capture strategy. Of the species tested, Resinicium bicolor was the most successful in spreading through the soil, and it replaced other species, including the pathogens. When R. bicolor was absent other cord-forming species were able to expand their domain. A new system for measuring competitive success was developed. `Pie slices` were cut from round wood-discs, and after preinoculation, the pieces were paired in all possible combinations on water agar. In this way, inoculum size could be varied while the size of the contact area remained the same. Large mycelia had more competitive success than did smaller ones when paired with the same species. In a pilot study, R. bicolor was most successful in replacing the opposing species and H. annosum had the least success. In general, species found late in the succession were strong competitors, while earlier colonizers had less success. Species acting as selective replacers of primary decay species were found to be more competitive than the latter. 134 refs, 8 figs, 1 tab

Broad Anatomical Variation within a Narrow Wood Density Range--A Study of Twig Wood across 69 Australian Angiosperms.

Directory of Open Access Journals (Sweden)

Kasia Ziemińska

Full Text Available Just as people with the same weight can have different body builds, woods with the same wood density can have different anatomies. Here, our aim was to assess the magnitude of anatomical variation within a restricted range of wood density and explore its potential ecological implications.Twig wood of 69 angiosperm tree and shrub species was analyzed. Species were selected so that wood density varied within a relatively narrow range (0.38-0.62 g cm-3. Anatomical traits quantified included wood tissue fractions (fibres, axial parenchyma, ray parenchyma, vessels, and conduits with maximum lumen diameter below 15 μm, vessel properties, and pith area. To search for potential ecological correlates of anatomical variation the species were sampled across rainfall and temperature contrasts, and several other ecologically-relevant traits were measured (plant height, leaf area to sapwood area ratio, and modulus of elasticity.Despite the limited range in wood density, substantial anatomical variation was observed. Total parenchyma fraction varied from 0.12 to 0.66 and fibre fraction from 0.20 to 0.74, and these two traits were strongly inversely correlated (r = -0.86, P < 0.001. Parenchyma was weakly (0.24 ≤|r|≤ 0.35, P < 0.05 or not associated with vessel properties nor with height, leaf area to sapwood area ratio, and modulus of elasticity (0.24 ≤|r|≤ 0.41, P < 0.05. However, vessel traits were fairly well correlated with height and leaf area to sapwood area ratio (0.47 ≤|r|≤ 0.65, all P < 0.001. Modulus of elasticity was mainly driven by fibre wall plus vessel wall fraction rather than by the parenchyma component.Overall, there seem to be at least three axes of variation in xylem, substantially independent of each other: a wood density spectrum, a fibre-parenchyma spectrum, and a vessel area spectrum. The fibre-parenchyma spectrum does not yet have any clear or convincing ecological interpretation.

Wood Ash Induced pH Changes Strongly Affect Soil Bacterial Numbers and Community Composition

DEFF Research Database (Denmark)

Bang-Andreasen, Toke; Nielsen, Jeppe T.; Voriskova, Jana

2017-01-01

Recirculation of wood ash from energy production to forest soil improves the sustainability of this energy production form as recycled wood ash contains nutrients that otherwise would be lost at harvest. In addition, wood-ash is beneficial to many soils due to its inherent acid......-neutralizing capabilities. However, wood ash has several ecosystem-perturbing effects like increased soil pH and pore water electrical conductivity both known to strongly impact soil bacterial numbers and community composition. Studies investigating soil bacterial community responses to wood ash application remain sparse...... and the available results are ambiguous and remain at a general taxonomic level. Here we investigate the response of bacterial communities in a spruce forest soil to wood ash addition corresponding to 0, 5, 22, and 167 t wood ash ha(-1). We used culture-based enumerations of general bacteria, Pseudomonas...

Self-sorting of guests and hard blocks in bisurea-based thermoplastic elastomers

NARCIS (Netherlands)

Botterhuis, N.E.; Karthikeyan, S.; Spiering, A.J.H.; Sijbesma, R.P.

2010-01-01

Self-sorting in thermoplastic elastomers was studied using bisurea-based thermoplastic elastomers (TPEs) which are known to form hard blocks via hierarchical aggregation of bisurea segments into ribbons and of ribbons into fibers. Self-sorting of different bisurea hard blocks in mixtures of polymers

Effect of thermoplastic appliance thickness on initial stress distribution in periodontal ligament

Directory of Open Access Journals (Sweden)

De-Shin Liu

2015-04-01

Full Text Available A numerical investigation into the initial stress distribution induced within the periodontal ligament by thermoplastic appliances with different thicknesses is performed. Based on the plaster model of a 25-year-old male patient, a finite element model of the maxillary lateral incisors and their supporting structures is constructed. In addition, four finite element models of thermoplastic appliances with different thicknesses in the range of 0.5–1.25 mm are also constructed based on the same plaster model. Finite element analysis simulations are performed to examine the effects of the force delivered by the thermoplastic appliances on the stress response of the periodontal ligament during the elastic recovery process. The results show that the stress induced in the periodontal ligament increases with an increasing appliance thickness. For example, the stress triples from 0.0012 to 0.0038 MPa as the appliance thickness is increased from 0.75 to 1.25 mm. The results presented in this study provide a useful insight into as a result of the compressive and tensile stresses induced by thermoplastic appliances of different thicknesses. Moreover, the results enable the periodontal ligament stress levels produced by thermoplastic appliances of different thicknesses to be reliably estimated.

Higher fungal diversity is correlated with lower CO2 emissions from dead wood in a natural forest.

Science.gov (United States)

Yang, Chunyan; Schaefer, Douglas A; Liu, Weijie; Popescu, Viorel D; Yang, Chenxue; Wang, Xiaoyang; Wu, Chunying; Yu, Douglas W

2016-08-24

Wood decomposition releases almost as much CO2 to the atmosphere as does fossil-fuel combustion, so the factors regulating wood decomposition can affect global carbon cycling. We used metabarcoding to estimate the fungal species diversities of naturally colonized decomposing wood in subtropical China and, for the first time, compared them to concurrent measures of CO2 emissions. Wood hosting more diverse fungal communities emitted less CO2, with Shannon diversity explaining 26 to 44% of emissions variation. Community analysis supports a 'pure diversity' effect of fungi on decomposition rates and thus suggests that interference competition is an underlying mechanism. Our findings extend the results of published experiments using low-diversity, laboratory-inoculated wood to a high-diversity, natural system. We hypothesize that high levels of saprotrophic fungal biodiversity could be providing globally important ecosystem services by maintaining dead-wood habitats and by slowing the atmospheric contribution of CO2 from the world's stock of decomposing wood. However, large-scale surveys and controlled experimental tests in natural settings will be needed to test this hypothesis.

Properties and performance of flax yarn/thermoplastic polyester composites

DEFF Research Database (Denmark)

Madsen, Bo; Mehmood, Shahid

2012-01-01

Aiming at demonstrating the potential of unidirectional natural fiber-reinforced thermoplastic composites in structural applications, textile flax yarn/thermoplastic polyester composites with variable fiber volume fractions have been manufactured by a filament-winding process followed by a vacuum......-assisted compression molding process. The microstructure of the composites shows that the flax fiber yarns are well impregnated by the polyester matrix, and this supports the measured low porosity content of the composites. The experimental tensile modulus and ultimate tensile stress of the composites in the axial...

Visual cues for woodpeckers: light reflectance of decayed wood varies by decay fungus

Science.gov (United States)

O'Daniels, Sean T.; Kesler, Dylan C.; Mihail, Jeanne D.; Webb, Elisabeth B.; Werner, Scott J.

2018-01-01

The appearance of wood substrates is likely relevant to bird species with life histories that require regular interactions with wood for food and shelter. Woodpeckers detect decayed wood for cavity placement or foraging, and some species may be capable of detecting trees decayed by specific fungi; however, a mechanism allowing for such specificity remains unidentified. We hypothesized that decay fungi associated with woodpecker cavity sites alter the substrate reflectance in a species-specific manner that is visually discriminable by woodpeckers. We grew 10 species of wood decay fungi from pure cultures on sterile wood substrates of 3 tree species. We then measured the relative reflectance spectra of decayed and control wood wafers and compared them using the receptor noise-limited (RNL) color discrimination model. The RNL model has been used in studies of feather coloration, egg shells, flowers, and fruit to model how the colors of objects appear to birds. Our analyses indicated 6 of 10 decayed substrate/control comparisons were above the threshold of discrimination (i.e., indicating differences discriminable by avian viewers), and 12 of 13 decayed substrate comparisons were also above threshold for a hypothetical woodpecker. We conclude that woodpeckers should be capable of visually detecting decayed wood on trees where bark is absent, and they should also be able to detect visually species-specific differences in wood substrates decayed by fungi used in this study. Our results provide evidence for a visual mechanism by which woodpeckers could identify and select substrates decayed by specific fungi, which has implications for understanding ecologically important woodpecker–fungus interactions.

Dendrological Characterization as Inspection Resources of Caatinga Wood Market

Directory of Open Access Journals (Sweden)

Rayssa de Medeiros Morais

2018-06-01

Full Text Available ABSTRACT This study aimed to distinguish five native forest species of the Caatinga Biome from the exotic invasive algaroba (Prosopis juliflora (Sw. DC., considering dendrologic characteristics of bark and wood, in order of providing subsidies for the inspection of the wood market in this Biome. The native species studied were jurema-preta (Mimosa tenuiflora (Willd. Poir., angico branco (Anadenanthera colubrina var. colubrina (Vell. Brenan, angico vermelho (Anadenanthera colubrina var. cebil (Gris. Alts., aroeira (Myracrodruon urundeuva Allem and braúna-do-sertão (Schinopsis brasiliensis Engl.. Studied species were recognized using dendrology identification records, containing characteristics of bark, heartwood and sapwood coloration; and the organoleptic proprieties like color, smell and taste, used for safe wood logs identification. The macroscopic characteristics, organized in dichotomous key, allowed the differentiation among the species, available in logs, during inspection.

Community turnover of wood-inhabiting fungi across hierarchical spatial scales.

Directory of Open Access Journals (Sweden)

Nerea Abrego

Full Text Available For efficient use of conservation resources it is important to determine how species diversity changes across spatial scales. In many poorly known species groups little is known about at which spatial scales the conservation efforts should be focused. Here we examined how the community turnover of wood-inhabiting fungi is realised at three hierarchical levels, and how much of community variation is explained by variation in resource composition and spatial proximity. The hierarchical study design consisted of management type (fixed factor, forest site (random factor, nested within management type and study plots (randomly placed plots within each study site. To examine how species richness varied across the three hierarchical scales, randomized species accumulation curves and additive partitioning of species richness were applied. To analyse variation in wood-inhabiting species and dead wood composition at each scale, linear and Permanova modelling approaches were used. Wood-inhabiting fungal communities were dominated by rare and infrequent species. The similarity of fungal communities was higher within sites and within management categories than among sites or between the two management categories, and it decreased with increasing distance among the sampling plots and with decreasing similarity of dead wood resources. However, only a small part of community variation could be explained by these factors. The species present in managed forests were in a large extent a subset of those species present in natural forests. Our results suggest that in particular the protection of rare species requires a large total area. As managed forests have only little additional value complementing the diversity of natural forests, the conservation of natural forests is the key to ecologically effective conservation. As the dissimilarity of fungal communities increases with distance, the conserved natural forest sites should be broadly distributed in space, yet

DecAID advisor: a tool for managing snags, down wood and wood decay in PNW forests.

Science.gov (United States)

Bruce G. Marcot; Grant Gunderson; Kim Mellen; Janet L. Ohmann

2004-01-01

Past tools for modeling and setting guidelines for snag and down wood management have been based on theory, professional judgment, models of wildlife species use as habitat and empirical data. However, recent studies reveal that guidelines for amounts of snags and down wood on national forests of Washington and Oregon may have been lower than the new field data on use...

Microbial Communities in Sunken Wood Are Structured by Wood-Boring Bivalves and Location in a Submarine Canyon

Science.gov (United States)

Fagervold, Sonja K.; Romano, Chiara; Kalenitchenko, Dimitri; Borowski, Christian; Nunes-Jorge, Amandine; Martin, Daniel; Galand, Pierre E.

2014-01-01

The cornerstones of sunken wood ecosystems are microorganisms involved in cellulose degradation. These can either be free-living microorganisms in the wood matrix or symbiotic bacteria associated with wood-boring bivalves such as emblematic species of Xylophaga, the most common deep-sea woodborer. Here we use experimentally submerged pine wood, placed in and outside the Mediterranean submarine Blanes Canyon, to compare the microbial communities on the wood, in fecal pellets of Xylophaga spp. and associated with the gills of these animals. Analyses based on tag pyrosequencing of the 16S rRNA bacterial gene showed that sunken wood contained three distinct microbial communities. Wood and pellet communities were different from each other suggesting that Xylophaga spp. create new microbial niches by excreting fecal pellets into their burrows. In turn, gills of Xylophaga spp. contain potential bacterial symbionts, as illustrated by the presence of sequences closely related to symbiotic bacteria found in other wood eating marine invertebrates. Finally, we found that sunken wood communities inside the canyon were different and more diverse than the ones outside the canyon. This finding extends to the microbial world the view that submarine canyons are sites of diverse marine life. PMID:24805961

Wood identification of Dalbergia nigra (CITES Appendix I) using quantitative wood anatomy, principal components analysis and naïve Bayes classification

Science.gov (United States)

Gasson, Peter; Miller, Regis; Stekel, Dov J.; Whinder, Frances; Ziemińska, Kasia

2010-01-01

Background and Aims Dalbergia nigra is one of the most valuable timber species of its genus, having been traded for over 300 years. Due to over-exploitation it is facing extinction and trade has been banned under CITES Appendix I since 1992. Current methods, primarily comparative wood anatomy, are inadequate for conclusive species identification. This study aims to find a set of anatomical characters that distinguish the wood of D. nigra from other commercially important species of Dalbergia from Latin America. Methods Qualitative and quantitative wood anatomy, principal components analysis and naïve Bayes classification were conducted on 43 specimens of Dalbergia, eight D. nigra and 35 from six other Latin American species. Key Results Dalbergia cearensis and D. miscolobium can be distinguished from D. nigra on the basis of vessel frequency for the former, and ray frequency for the latter. Principal components analysis was unable to provide any further basis for separating the species. Naïve Bayes classification using the four characters: minimum vessel diameter; frequency of solitary vessels; mean ray width; and frequency of axially fused rays, classified all eight D. nigra correctly with no false negatives, but there was a false positive rate of 36·36 %. Conclusions Wood anatomy alone cannot distinguish D. nigra from all other commercially important Dalbergia species likely to be encountered by customs officials, but can be used to reduce the number of specimens that would need further study. PMID:19884155

A new shock wave assisted wood preservative injection system

Science.gov (United States)

Rao, K. S.; Ravikumar, G.; Lai, Ram; Jagadeesh, G.

Preservative treatment of many tropical hard woods and bamboo pose severe problem. A number of wood preservatives (chemical formulations toxic to wood decay/ destroying organisms like fungi, wood destroying termites, marine borers etc.) and wood impregnating techniques are currently in use for improving bio resistance of timber and bamboo and thereby enhancing service life for different end uses. How ever, some species of tropical hardwoods and many species of bamboo are difficult to treat, posing technical problems. In this paper we report preliminary results of treatment of bamboo with a novel Shockwave assisted injection treatment. Samples (30×2.5×1.00 cm) of an Indian species of bamboo Dendrocalamus strictus prepared from defect free culms of dry bamboo are placed in the driven section of a vertical shock tube filled with the 4Coppepr-Chrome-Arsenic(CCA) preservative solution.The bamboo samples are subjected to repeated shock wave loading (3 shots) with typical over pressures of 30 bar. The results from the study indicate excellent penetration and retention of CCA preservative in bamboo samples. The method itself is much faster compared to the conventional methods like pressure treatment or hot and cold process.

Cement bonded wood wool boards from podocarpus spp. for low ...

African Journals Online (AJOL)

... sound insulation in walls, ceilings and floors, roofs, sound barriers and thermal insulation. Further research is required to investigate the use of different wood species and different mineral binders. Keywords: podocarpus spp, wood-wool, wood-cement composites. Journal of Civil Engineering Research and Practice Vol.

CREEP BEHAVIOR OF BORATE-TREATED STRANDBOARD: EFFECT OF ZINC BORATE RETENTION, WOOD SPECIES, AND LOAD LEVEL

OpenAIRE

Wu,Qinglin; Lee,Ong N; Cai,Zhiyong; Zhou,Dingguo

2009-01-01

Creep performance of zinc borate-treated strandboard from southern pine (Pinus taeda L.) and red oak (Quercus falcata) was investigated at 25(0)C temperature and 65% relative humidity. It was shown that the borate treatment had some significant effect on creep deflection of the test panels, and the effect varied with wood species. There was no significant effect of creep loading on residual bending properties of treated strandboard under the stress levels used. The four element spring-dashpot...

Bacterial community succession in pine-wood decomposition

Directory of Open Access Journals (Sweden)

Anna eKielak

2016-03-01

Full Text Available Though bacteria and fungi are common inhabitants of decaying wood, little is known about the relationship between bacterial and fungal community dynamics during natural wood decay. Based on previous studies involving inoculated wood blocks, strong fungal selection on bacteria abundance and community composition was expected to occur during natural wood decay. Here we focused on bacterial and fungal community compositions in pine wood samples collected from dead trees in different stages of decomposition. We showed that bacterial communities undergo less drastic changes than fungal communities during wood decay. Furthermore, we found that bacterial community assembly was a stochastic process at initial stage of wood decay and became more deterministic in later stages, likely due to environmental factors. Moreover, composition of bacterial communities did not respond to the changes in the major fungal species present in the wood but rather to the stage of decay reflected by the wood density. We concluded that the shifts in the bacterial communities were a result of the changes in wood properties during decomposition and largely independent of the composition of the wood-decaying fungal communities.

The effect of crosslinker on mechanical and morphological properties of tropical wood material composites

International Nuclear Information System (INIS)

Islam, Md. Saiful; Hamdan, Sinin; Rahman, Md. Rezaur; Jusoh, Ismail; Ahmed, Abu Saleh

2011-01-01

In this study, wood polymer composites (WPCs) based on five kinds of selected tropical wood species, namely Jelutong (Dyera costulata), Terbulan (Endospermum diadenum), Batai (Paraserianthes moluccana), Rubber (Hevea brasiliensis), and Pulai (Alstonia pneumatophora), were impregnated with methyl methacrylate (MMA) and hexamethylene diisocyanate (HMDIC) monomers mixture in the ratio of 1:1 for composite manufacturing. All these tropical wood reacted with hexamethylene diisocyanate and crosslinked with MMA which enhanced the hydrophobic (restrained water) nature of wood. The vacuum-pressure method was used to impregnate the samples with monomer mixture. The monomer mixture loading achievable was found to be dependent on the properties of wood species. Low loading was observed for the high density wood species. Mechanical strength of fabricated wood polymer composites (WPCs) in term of modulus of elasticity (MOE) and modulus of rupture (MOR) were found to be significantly improved. The wood-polymer interaction was confirmed by Fourier transform infrared (FTIR) spectroscopy. Morphological properties of raw wood and WPC samples were evaluated by scanning electron microscopy (SEM) and XRD analysis and an improvement in morphological properties was also observed for WPC.

Aspen SUCROSE TRANSPORTER3 Allocates Carbon into Wood Fibers1[C][W

Science.gov (United States)

Mahboubi, Amir; Ratke, Christine; Gorzsás, András; Kumar, Manoj; Mellerowicz, Ewa J.; Niittylä, Totte

2013-01-01

Wood formation in trees requires carbon import from the photosynthetic tissues. In several tree species, including Populus species, the majority of this carbon is derived from sucrose (Suc) transported in the phloem. The mechanism of radial Suc transport from phloem to developing wood is not well understood. We investigated the role of active Suc transport during secondary cell wall formation in hybrid aspen (Populus tremula × Populus tremuloides). We show that RNA interference-mediated reduction of PttSUT3 (for Suc/H+ symporter) during secondary cell wall formation in developing wood caused thinner wood fiber walls accompanied by a reduction in cellulose and an increase in lignin. Suc content in the phloem and developing wood was not significantly changed. However, after 13CO2 assimilation, the SUT3RNAi lines contained more 13C than the wild type in the Suc-containing extract of developing wood. Hence, Suc was transported into developing wood, but the Suc-derived carbon was not efficiently incorporated to wood fiber walls. A yellow fluorescent protein:PttSUT3 fusion localized to plasma membrane, suggesting that reduced Suc import into developing wood fibers was the cause of the observed cell wall phenotype. The results show the importance of active Suc transport for wood formation in a symplasmically phloem-loading tree species and identify PttSUT3 as a principal transporter for carbon delivery into secondary cell wall-forming wood fibers. PMID:24170204

Consumer preference study of characteristics of Hawaiian koa wood bowls

Science.gov (United States)

Eini C Lowell; Katherine Wilson; Jan Wiedenbeck; Catherine Chan; J. B. Friday; Nicole Evans

2017-01-01

Koa (Acacia koa A. Gray), a species endemic to the Hawaiian Islands, has ecological, cultural, and economic significance. Its wood is prized globally but today, most woodworkers only use koa wood from dead and dying old-growth trees. The general perception of wood from young-growth koa is that it lacks the color and figure of old-growth wood and is...

77 FR 26191 - Endangered and Threatened Wildlife and Plants; Reclassifying the Wood Bison Under the Endangered...

Science.gov (United States)

2012-05-03

...; Reclassifying the Wood Bison Under the Endangered Species Act as Threatened Throughout Its Range AGENCY: Fish... that the wood bison no longer meets the definition of endangered under the Endangered Species Act. This... Endangered Species Act, some threats to wood bison remain. Habitat loss has occurred in Canada from...

Biodegrading effects of some rot fungi on Pinus caribaea wood

African Journals Online (AJOL)

STORAGESEVER

2008-05-16

May 16, 2008 ... species of white-rot fungi; Corioliopsis polyzona and Pleurotus squarrosulus, and two species of brown- rot fungi; Lentinus ... The results indicated that biodegradation by rot fungi differs in intensity according to the fungus ..... wood of coast red wood Sequoia Sempervirens (D. Don). For. Prod. J. 33(5): 15-20 ...

An Analysis of the U.S. Wood Products Import Sector: Prospects for Tropical Wood Products Exporters

Directory of Open Access Journals (Sweden)

W.A.R.T.W. Bandara

2012-10-01

Full Text Available The U.S. has dramatically altered its wood product imports and exports during the past few years,and at present, it is the second largest wood product importer in the world. Hence, an understanding ofmarket structures, factors in selecting foreign suppliers, and the emphasis placed on environmentalissues/certification are critical to understand from the perspective of wood products importers in the U.S.This study provides an analysis of the U.S. wood products import sector with special emphasis on currentand future opportunities for tropical wood products exporters to the U.S. market.In this study, 158 wood products importers in the U.S. were surveyed using a mailingquestionnaire. The adjusted response rate was 40.6 percent. Results indicated that most of the respondentswere small to medium scale firms, but major importers of wood products. According to respondents,wood products to the U.S. mainly come from Brazil, Chile, and China. From the importers’ perspective,Brazilian wood products ranked first for its quality followed by wood products from Chile and Finland.Product quality, long term customer relationships, on-time delivery of orders, fair prices, and supplierreputation were the factors deemed important in selecting overseas suppliers. Majority of respondentswere importing certified wood products. FSC, SFI, and ISO 14000 were the mostly accepted certificationprograms. However, certification was not a major factor in foreign supplier selection criteria. Whenconsidered the U.S. wood products importers’ tendency to diversify their products and species imported,attractive opportunities exist for wood products suppliers from tropical countries.

Training programme impact on thermoplastic immobilization for head and neck radiation therapy

International Nuclear Information System (INIS)

Outhwaite, Julie-Anne; McDowall, W. Robert; Marquart, Louise; Rattray, Gregory; Fielding, Andrew; Hargrave, Catriona

2013-01-01

Purpose: To determine whether uniform guidelines and training in the stabilization and formation of thermoplastic shells can improve the reproducibility of set-up for Head and Neck cancer patients. Methods and materials: Image based measurements of the planning and treatment positions for 35 head and neck cancer patients undergoing radical radiotherapy were analysed to provide a baseline of the reproducibility of thermoplastic immobilization. Radiation therapists (RT) were surveyed to establish a perception of their confidence in thermoplastic procedures. An evidence based staff training programme was created and implemented. Set-up reproduction and staff perception were reviewed to measure the impact of the training programme. Results: The mean (SD) 3D vectors of anatomical displacement, measured on the patient images, improved from 4.64 (2.03) for the baseline group compared to 3.02 (1.65) following training (p < 0.01). The proportion of 3D displacements of patient data exceeding 5 mm 3D vector was decreased from 37.1% to 5.7% (p < 0.001) and the 3 mm vector from 85.7% to 42.9% (p < 0.001). The post-training survey scores demonstrated improved confidence in reproducibility of set-up for head and neck patients. Conclusion: The Thermoplastic Shells Training Program has been found to improve the treatment reproducibility for head and neck radiation therapy patients. Uniform guidelines have increased RT confidence in thermoplastic procedures.

The reactive extrusion of thermoplastic polyurethane

NARCIS (Netherlands)

Verhoeven, Vincent Wilhelmus Andreas

2006-01-01

The objective of this thesis was to increase the understanding of the reactive extrusion of thermoplastic polyurethane. Overall, several issues were identified: • Using a relative simple extrusion model, the reactive extrusion process can be described. This model can be used to further investigate

Optimising hydrogen bonding in solid wood

DEFF Research Database (Denmark)

Engelund, Emil Tang

2009-01-01

The chemical bonds of wood are both covalent bonds within the wood polymers and hydrogen bonds within and between the polymers. Both types of bonds are responsible for the coherence, strength and stiffness of the material. The hydrogen bonds are more easily modified by changes in load, moisture...... and temperature distorting the internal bonding state. A problem arises when studying hydrogen bonding in wood since matched wood specimens of the same species will have very different internal bonding states. Thus, possible changes in the bonding state due to some applied treatment such as conditioning...... maintaining 100 % moisture content of the wood. The hypothesis was that this would enable a fast stress relaxation as a result of reorganization of bonds, since moisture plasticizes the material and temperature promotes faster kinetics. Hereby, all past bond distortions caused by various moisture, temperature...

Thermosetting epoxy resin/thermoplastic system with combined shape memory and self-healing properties

International Nuclear Information System (INIS)

Yao, Yongtao; Wang, Jingjie; Lu, Haibao; Liu, Yanju; Leng, Jinsong; Xu, Ben; Fu, Yongqing

2016-01-01

A novel and facile strategy was proposed to construct a thermosetting/thermoplastic system with both shape memory and self-healing properties based on commercial epoxy resin and poly(ϵ-caprolactone)-PCL. Thermoplastic material is capable of re-structuring and changing the stiffness/modulus when the temperature is above melting temperature. PCL microfiber was used as a plasticizer in epoxy resin–based blends, and served as a ‘hard segment’ to fix a temporary shape of the composites during shape memory cycles. In this study, the electrospun PCL membrane with a porous network structure enabled a homogenous PCL fibrous distribution and optimized interaction between fiber and epoxy resin. The self-healing capability is achieved by phase transition during curing of the composites. The mechanism of the shape memory effect of the thermosetting (rubber)/thermoplastic composite is attributed to the structural design of the thermoplastic network inside the thermosetting resin/rubber matrix. (paper)

Evaluation of fuel wood quality of four fuel tree species used for fish smoking in the Sene District of the Brong Ahafo Region of Ghana

International Nuclear Information System (INIS)

Neequaye-Tetteh, G.A.; Quashie-Sam, S.J.; Dassah, A. L.

2004-01-01

Full text. The fuel wood quality of four trees, Terminalia avicennoides, Anogeissus Ieiocarpus, Combretum ghasalense and Pterocarpus arinaceus, which are easily available and widely used as fuel wood for fish smoking in the Sene District of the Brong Ahafo Region of Ghana was assessed. The specific gravity, calorific values, and burning times were determined. The mean specific gravity values for T. avicennoides, A. leiocarpus, C. ghasalense, and P. erinaceus were 0.97, 0.96, and 0.97, respectively. These values were not significantly different (P<0.05). The calorific values were 19,368.0 kj/kg for T avicennoides, 18,905.2 kj/kg for A. leiocarpus, 18,665.8 kj/kg for C. ghasalense, and 19,694.1 kj/kg for P. erinaceus. The values were not significantly different (P<0.05) between T. avicennoides and A. leiocarpus and C. ghasalense. However, there were significant differences (P<0.05) in the calorific values between T. avicennoides and C. ghasalense, A. leiocarpus and P. erinaceus, and C. ghasalense and P. erinaceus. The time in minutes required in burning equal lengths (60 cm) of the four species of fuel wood were 360 for T. avicennoides, 260 for A. leiocarpus, 195 for C. ghasalense, and 175 for P. erinaceus. These values were significantly different (P<0.0 1), with P. erinaceus burning almost twice as fast as T. avicennoides. Ranking the four fuel wood species from least to highest burning times, T. avicennoides burnt slowest, followed by A. leiocarpus, C. ghasalense, and P. erinaceuse. The specific gravity and calorific values recorded indicate that wood from the four species is suitable for use as fuel. Terminalia avicennoides, which burnt slowest, was most preferred for fish smoking, followed by A. leiocarpus and C. ghasalense. The fast-burning P. erinaceus was least preferred for fish smoking. (au)

Processing technology for advanced fibre composites with thermoplastic matrices

Energy Technology Data Exchange (ETDEWEB)

Lystrup, Aa. [Risoe National Lab., Materials Research Dept., Roskilde (Denmark)

1997-12-31

Technologies and semi-raw materials for the manufacture of thermoplastic composites with continuous fibres are discussed. Autoclave consolidation, vacuum consolidation and press consolidation are all processes which are suitable for the manufacture of components with a three dimensional geometry. Autoclave consolidation is primarily for high quality components with high fibre content and complex geometry; using vacuum consolidation, very large components can be produced without the need of an autoclave, and the press consolidation technique is a very fast process suitable for mass production of smaller parts. Filament winding is used primarily for the manufacture of rotationally symmetrical components, and some of the technologies in use are winding with a continuously in-situ consolidation, winding inside an oven and room temperature winding followed by an autoclave consolidation. Semi-raw materials for thermoplastic composites exist as both prepregs and postpregs in many different forms, of which many are still under development. Some of the basic processing properties for the different types of semi-raw materials and most commonly used thermoplastic polymers are given. (au) 37 refs.

Wood supply at the edge of the world

DEFF Research Database (Denmark)

Pinta, Elie; Baittinger, Claudia

Wood used in construction and boat building, in domestic productions or as a fuel resource was a key material for medieval North European societies. For people living in Medieval Scandinavia, trees and timber were common in both landscapes and mythology and therefore essential cultural items...... is to present the current research on the identification of wood species (both local and imported) used by European settlers in Greenland. An analysis of wood will help us to understand and retrace the origin and circulation of wood resources in the Norse settlements. What was the nature of woodworking...

Studies on the structure and properties of thermoplastic starch/luffa fiber composites

International Nuclear Information System (INIS)

Kaewtatip, Kaewta; Thongmee, Jariya

2012-01-01

Highlights: ► Thermoplastic starch/luffa fiber composites were prepared using compression molding. ► The tensile strengths of the composites were higher than for thermoplastic starch. ► Degradation temperatures of the composites were higher than for thermoplastic starch. ► Luffa fiber decreases the water absorption of TPS. -- Abstract: Thermoplastic starch (TPS)/luffa fiber composites were prepared using compression molding. The luffa fiber contents ranged from 0 wt.% to 20 wt.%. The tensile strength of the TPS/luffa fiber composite with 10 wt.% of luffa fiber had a twofold increase compared to TPS. The temperature values of maximum weight loss of the TPS/luffa fiber composites were higher than for TPS. The water absorption of the TPS/luffa fiber composites decreased significantly when the luffa fiber contents increased. The strength of adhesion between the luffa fiber and the TPS matrix was clearly demonstrated by their compatibility presumably due to their similar chemical structures as shown by scanning electron microscope (SEM) micrographs and Fourier transform infrared (FTIR) spectra.

Wood evidence : proper collection, documentation, and storage of wood evidence from a crime scene

Science.gov (United States)

Alex Wiedenhoeft

2006-01-01

Wood can be found at crime scenes in many forms: as a murder weapon, as material used to hide a body, or as trace evidence from forced entry or vandalism. In the course of my work at the Forest Products Laboratory, Center for Wood Anatomy Research, I have been part of several forensic investigations that were adversely affected by inappropriate procedures used to...

The influence of technological parameters on the dynamic behavior of "liquid wood" samples obtained by injection molding

Science.gov (United States)

Plavanescu Mazurchevici, Simona; Carausu, Constantin; Comaneci, Radu; Nedelcu, Dumitru

2017-10-01

The plastic products contribute to environmental pollution. Replacing the plastic materials with biodegradable materials with superior properties is an absolute necessity and important research direction for the near future. The first steps in this regard were the creation of composite materials containing natural fibers with positive effects on the environment that have penetrated in different fields. The bioplastics and biocomposites made from natural fibers is a topical solution. The next step was made towards obtaining biodegradable and recyclable materials based on cellulose, lignin and no carcinogens. In this category fall the "liquid wood" with a use up to five times without affecting the mechanical properties. "Liquid wood" is a high quality thermoplastic biocomposite. "Liquid wood" is a biopolymer composite divided in three categories, ARBOFORM®, ARBOBLEND® and ARBOFILL®, which have differed composition in terms of lignin percentage, being delivered by Tecnaro, as granules, [1]. The paper's research was focus on Arboform L V3 Nature and Arboform L V3 Nature reinforced with aramid fiber. In the experimental plan were taken into account six parameters (Dinj - direction of injection [°]; Ttop - melting temperature [°C]; Pinj - injection pressure [MPa] Ss - speed [m/min]; tinj - injection time [s] and tc - cooling time [s]) each with two levels, research carried on by Taguchi methodology. Processing Taguchi method allowed both Taguchi setting work parameters influence on storage modulus and damping as the size and influence their ranking. Experimental research concerning the influence technological parameters on storage modulus of samples obtained by injection from Arboform L V3 Nature yielded an average of 6055MPa and descending order as follows: Trac, Ss, Pinj, Dinj and Ttop. The average of model for reinforced material was 6419MPa and descending order of parameters influence such as: Dinj, Trac, Ttop, tinj, Ss and Pinj.

Thermoplastic Elastomers From Chemically or Irradiation Activated Polyolefin Wastes and Ground Tyre Rubber

International Nuclear Information System (INIS)

Tolstov, A.M.; Grigoryeva, A.L.; Bardash, O.P.

2005-01-01

Thermoplastic elastomers (TPE) are known as materials with unique combination of elastomeric properties and thermo plasticity. Among the TPE of different type the polymer blends of thermoplastics and rubbers are the most commonly used. Recently a very effective technology of dynamic vulcanization of rubber component inside thermoplastic matrix has been developed. As a result of rubber vulcanization and dispersion inside thermoplastic the new type of TPE so-called thermoplastic dynamic vulcanizations (TPV) are obtained. In our work we have applied the technology of dynamic vulcanization for recycled components (PP, HDPE, GTR). It has appeared that such components are not mixed well and the resulting TPV have poor mechanical properties. To solve a problem of poor compatibility of the components used we carried out a pre-modification (functionalization) of the component surfaces by gamma-irradiation or by chemically or gamma-irradiation induced grafting of reactive monomers. Both the polyolefin (HDPE) and GTR were functionalized before mixing. The monomers were selected by such a way that being grafted to be able to react to each other in interface during the components blending. For example, we used maleic anhydride and acrylamide. The effect of better compatibility has appeared in higher tensile characteristics of TPV synthesized

Wood-polymer composites obtained by gamma radiation

International Nuclear Information System (INIS)

Gago, Javier; Lopez, Alcides; Rodriguez, Juan; Universidad Nacional de Ingenieria, Lima; Acevedo, Moises; Santiago, Julio; Universidad Nacional Mayor de San Marcos, Lima

2006-01-01

It has been prepared composites materials by means of monomer penetration in pores of wood samples and later curing by means of gamma irradiation. The studied species were Hura crepitans L. (catahua), Aniba puchury-minor (C. Martinez) (mohena amarilla), and Calycophyllum spruceanum (Benth.) (capirona). These new materials exhibit smaller water absorption and better mechanical properties in comparison with native wood. The test tubes of catahua treated with the styrene-polyester mixture absorb only up to 10% humidity compared to the native species whereas its hardness is increased in a 100%. (author)

Direct and indirect drivers of instream wood in the interior Pacific Northwest, USA: decoupling climate, vegetation, disturbance, and geomorphic setting

Directory of Open Access Journals (Sweden)

Hough-Snee Nate

2014-06-01

Full Text Available Instream wood is a driver of geomorphic change in low-order streams, frequently altering morphodynamic processes. Instream wood is a frequently measured component of streams, yet it is a complex metric, responding to ecological and geomorphic forcings at a variety of scales. Here we seek to disentangle the relative importance of physical and biological processes that drive wood growth and delivery to streams across broad spatial extents. In so doing, we ask two primary questions: (1 is riparian vegetation a composite variable that captures the indirect effects of climate and disturbance on instream wood dynamics? (2 What are the direct and indirect relationships between geomorphic setting, vegetation, climate, disturbance, and instream wood dynamics? We measured riparian vegetation composition and wood frequency and volume at 720 headwater reaches within the American interior Pacific Northwest. We used ordination to identify relationships between vegetation and environmental attributes, and subsequently built a structural equation model to identify how climate and disturbance directly affect vegetation composition and how vegetation and geomorphic setting directly affect instream wood volume and frequency. We found that large wood volume and frequency are directly driven by vegetation composition and positively correlated to wildfire, elevation, stream gradient, and channel bankfull width. Indicator species at reaches with high volumes of wood were generally long-lived, conifer trees that persist for extended durations once delivered to stream habitats. Wood dynamics were also indirectly mediated by factors that shape vegetation: wildfire, precipitation, elevation, and temperature. We conclude that wood volume and frequency are driven by multiple interrelated climatic, geomorphic, and ecological variables. Vegetation composition and geomorphic setting directly mediate indirect relationships between landscape environmental processes and instream

Synthesis of thermoplastic elastomer using potassium persulfate and ammonium peroxydisulfate initiator

International Nuclear Information System (INIS)

Dewi Sondari; Agus Haryono; M Ghozali; Ahmad Randy; Kuntari Adi Suhardjo; Ariyadi B; Surasno

2010-01-01

Thermoplastic elastomer is polymeric material that has elastomer and thermoplastic properties. This material can be easily molded into finished and recyclable goods, thus environmentally safe for long term application. In this study we synthesize thermoplastic elastomer using two initiator that are potassium persulfate and ammonium peroxydisulfate with natural rubber to monomer (styrene/methyl methacrylate) ratio of 50 : 50 and 60 : 40 (v/v). The process of thermoplastic elastomer synthesis was conducted with emulsion grafting polymerization method for 6 hours at 65 °C. We used sodium dodecyl sulfate as emulsifier. FT-IR analysis result shows that grafting process had already occurred shown by new peaks that were observed in 1743 and 1519 cm"-"1. These peaks was assigned to carbonyl (C=O) group of methyl methacrylate and C=C benzene of styrene respectively. From "1H-NMR new peaks at δ = 7.1 ppm was aromatic proton from phenyl group of styrene, at δ = 3.5 ppm was methoxy proton of grafted methyl methacrylate acrylic group, and at δ = 5.1 ppm that is resonance of isoprene methine proton. This result showed that methyl methacrylate and styrene had already grafted onto natural rubber backbone. Initiator influenced grafting efficiency. Potassium persulfate gave 97.6 % grafting efficiency while ammonium peroxydisulfate gave 90.2 % grafting efficiency. (author)

Thermal Degradation, Mechanical Properties and Morphology of Wheat Straw Flour Filled Recycled Thermoplastic Composites

Directory of Open Access Journals (Sweden)

Kadir Karakus

2008-01-01

Full Text Available Thermal behaviors of wheat straw flour (WF filled thermoplastic compositeswere measured applying the thermogravimetric analysis and differential scanningcalorimetry. Morphology and mechanical properties were also studied using scanningelectron microscope and universal testing machine, respectively. Presence of WF inthermoplastic matrix reduced the degradation temperature of the composites. One for WFand one for thermoplastics, two main decomposition peaks were observed. Morphologicalstudy showed that addition of coupling agent improved the compatibility between WFs andthermoplastic. WFs were embedded into the thermoplastic matrix indicating improvedadhesion. However, the bonding was not perfect because some debonding can also be seenon the interface of WFs and thermoplastic matrix. In the case of mechanical properties ofWF filled recycled thermoplastic, HDPE and PP based composites provided similar tensileand flexural properties. The addition of coupling agents improved the properties ofthermoplastic composites. MAPE coupling agents performed better in HDPE while MAPPcoupling agents were superior in PP based composites. The composites produced with thecombination of 50-percent mixture of recycled HDPE and PP performed similar with theuse of both coupling agents. All produced composites provided flexural properties requiredby the ASTM standard for polyolefin-based plastic lumber decking boards.

Volume loss as a tool to assess kiln drying of eucalyptus wood

Directory of Open Access Journals (Sweden)

Djeison Cesar Batista

Full Text Available In this study, we aimed to analyze the kiln drying quality of Eucalyptus grandis, Eucalyptus saligna and Eucalyptus dunnii woods with respect to volume loss. Wood from the three species was kiln dried together with the same drying schedule and conditions in a conventional-temperature pilot kiln. Three kinds of volume loss were evaluated: total - from saturated (initial to machined (final condition; shrinkage - from saturated to 10% moisture content; and machining - from 10% moisture content to machined condition. Eucalyptus grandis wood was the most dimensionally stable and presented the smallest volume loss due to shrinkage. Although they had different shrinkage behaviors, Eucalyptus grandis and Eucalyptus saligna woods presented the same drying quality regarding machining and total volume losses. These species can be considered the same for kiln drying. Eucalyptus dunnii wood presented the worst quality in drying, and should not be kiln dried in the same batch with the other species.

Research Concerning the Shearing Strength of Black Locust Wood

Directory of Open Access Journals (Sweden)

Mihaela POROJAN

2011-06-01

Full Text Available The paper presents the experimental resultsobtained for the shearing strength of black locustwood (Robinia pseudacacia L. harvested from twogeographical areas (North and South of Romania.Wood is subjected to shearing stress when usedwithin different fields, and especially inconstructions. Tangential stresses are produced inthe shearing sections and they are influenced by thestructure of wood through the position of theshearing plane and of the force direction towards thegrain. Accordingly, several shearing types arepossible. The shearing strengths for the three mainshearing types, both on radial and tangentialdirection were determined within the present study.The evaluation of data was achieved by using theANOVA analysis, in order to test the level ofsignificance depending on the shearing planeorientation and the harvesting area. The obtainedresults were compared to the values mentionedwithin reference literature for this wood species andtwo other hardwood species with similar density. It isworth to be mentioned that the shearing strengths ofblack locust wood from Romania (both from Northand South are generally higher than those indicatedby reference literature for oak and beech. Thisrecommends black locust wood as constructionwood and for other applications where wood issubjected to shearing stress.

Toxicological Implications of Released Particulate Matter during Thermal Decomposition of Nano-Enabled Thermoplastics.

Science.gov (United States)

Watson-Wright, Christa; Singh, Dilpreet; Demokritou, Philip

2017-01-01

Nano-enabled thermoplastics are part of the growing market of nano-enabled products (NEPs) that have vast utility in several industries and consumer goods. The use and disposal of NEPs at their end of life has raised concerns about the potential release of constituent engineered nanomaterials (ENMs) during thermal decomposition and their impact on environmental health and safety. To investigate this issue, industrially relevant nano-enabled thermoplastics including polyurethane, polycarbonate, and polypropylene containing carbon nanotubes (0.1 and 3% w/v, respectively), polyethylene containing nanoscale iron oxide (5% w/v), and ethylene vinyl acetate containing nanoscale titania (2 and 5% w/v) along with their pure thermoplastic matrices were thermally decomposed using the recently developed lab based Integrated Exposure Generation System (INEXS). The life cycle released particulate matter (called LCPM) was monitored using real time instrumentation, size fractionated, sampled, extracted and prepared for toxicological analysis using primary small airway epithelial cells to assess potential toxicological effects. Various cellular assays were used to assess reactive oxygen species and total glutathione as measurements of oxidative stress along with mitochondrial function, cellular viability, and DNA damage. By comparing toxicological profiles of LCPM released from polymer only (control) with nano-enabled LCPM, potential nanofiller effects due to the use of ENMs were determined. We observed associations between NEP properties such as the percent nanofiller loading, host matrix, and nanofiller chemical composition and the physico-chemical properties of released LCPM, which were linked to biological outcomes. More specifically, an increase in percent nanofiller loading promoted a toxicological response independent of increasing LCPM dose. Importantly, differences in host matrix and nanofiller composition were shown to enhance biological activity and toxicity of LCPM

High performance thermoplastics - A review of neat resin and composite properties

Science.gov (United States)

Johnston, Norman J.; Hergenrother, Paul M.

1987-01-01

A review was made of the principal thermoplastics used to fabricate high performance composites. Neat resin tensile and fracture toughness properties, glass transition temperatures (Tg), crystalline melt temperatures (Tm) and approximate processing conditions are presented. Mechanical properties of carbon fiber composites made from many of these thermoplastics are given, including flexural, longitudinal tensile, transverse tensile and in-plane shear properties as well as short beam shear and compressive strengths and interlaminar fracture toughness.

Polycyanurates and Polycarbonates Based on Eugenol: Alternatives to Thermosetting and Thermoplastic Polymers Based on Bisphenol A

Science.gov (United States)

2014-08-14

to 5a. CONTRACT NUMBER In-House Thermosetting and Thermoplastic Polymers based on Bisphenol A 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6...Francisco, CA, 14 August 2014. PA#14389 14. ABSTRACT Polycyanurate thermosetting networks, polycarbonate thermoplastics, and homogenous polycarbonate...ON EUGENOL: ALTERNATIVES TO THERMOSETTING AND THERMOPLASTIC POLYMES BASED ON BISPHENOL A 14 August 2014 Andrew J. Guenthner1, Benjamin G. Harvey2

Characterisation of metal–thermoplastic composite hybrid joints by means of a mandrel peel test

NARCIS (Netherlands)

Su, Yibo; de Rooij, Matthias B.; Grouve, Wouter Johannes Bernardus; Warnet, Laurent

2016-01-01

Fastener free metal–carbon fibre reinforced thermoplastic composite hybrid joints show potential for application in aerospace structures. The strength of the metal–thermoplastic composite interface is crucial for the performance of the entire hybrid joint. Optimisation of the interface requires an

Sustainable wood waste management in Nigeria

Directory of Open Access Journals (Sweden)

Owoyemi Jacob Mayowa

2016-09-01

Full Text Available Wood industries produce large volumes of residues which must be utilized, marketed or properly disposed of. Heaps of wood residues are common features in wood industries throughout the year. In Nigeria, this residue is generally regarded as waste and this has led to open burning practices, dumping in water bodies or dumping in an open area which constitutes environmental pollution. Sawmills in Nigeria generated over 1,000,000 m3 of wood waste in 2010 while about 5000 m3 of waste was generated in plywood mills. Nigeria generates about 1.8 million tons of sawdust annually and 5.2 million tons of wood wastes. The impact of improper disposal of waste wood on the environment affects both the aquatic and terrestrial ecosystems. Also burning of waste wood releases greenhouse gases into the atmosphere causing various health issues. Reuse/recycling of these wood residues in Nigeria will reduce the pressure on our ever decreasing forests, reduce environmental pollution, create wealth and employment. The literature available on this subject was reviewed and this article, therefore, focuses on the various methods of wood waste disposal and its utilization in Nigerian wood industries, the effects of wood waste on the environment as well as on human health and the benefits of proper wood waste management practices.

A geographical analysis of the Swedish wood fuel market

International Nuclear Information System (INIS)

Roos, Anders; Bohlin, Folke; Hektor, Bo; Hillring, Bengt; Parikka, Matti

2000-01-01

The geographical variation in Swedish wood fuel market characteristics for the district heating sector has been studied using Geographical Information Systems (GIS) and cross-sectional Tobit analysis. The results indicate that local availability and competition for wood fuels influence the wood fuel consumption at inland heating plants. The factors affecting the decision to use wood fuel at heating plants close to seaports, however, were not captured by the model, suggesting that coastal location reduces dependency on the local wood fuel market. The effects of changes in local wood fuel availability on wood fuel use by an inland heating plant are presented and discussed

Ultrasonic assisted consolidation of commingled thermoplastic/glass fibers rovings

Directory of Open Access Journals (Sweden)

Francesca eLionetto

2015-04-01

Full Text Available Thermoplastic matrix composites are finding new applications in different industrial area thanks to their intrinsic advantages related to environmental compatibility and processability. The approach presented in this work consists in the development of a technology for the simultaneous deposition and consolidation of commingled thermoplastic rovings through to the application of high energy ultrasound. An experimental equipment, integrating both fiber impregnation and ply consolidation in a single process, has been designed and tested. It is made of an ultrasonic welder, whose titanium sonotrode is integrated on a filament winding machine. During winding, the commingled roving is at the same time in contact with the mandrel and the horn. The intermolecular friction generated by ultrasound is able to melt the thermoplastic matrix and impregnate the reinforcement fibers. The heat transfer phenomena occurring during the in situ consolidation were simulated solving by finite element (FE analysis an energy balance accounting for the heat generated by ultrasonic waves and the melting characteristics of the matrix. To this aim, a calorimetric characterization of the thermoplastic matrix has been carried out to obtain the input parameters for the model. The FE analysis has enabled to predict the temperature distribution in the composite during heating and cooling The simulation results have been validated by the measurement of the temperature evolution during ultrasonic consolidation.The reliability of the developed consolidation equipment was proved by producing hoop wound cylinder prototypes using commingled continuous E-glass rovings and Polypropylene (PP filaments. The consolidated composite cylinders are characterized by high mechanical properties, with values comparable with the theoretical ones predicted by the micromechanical analysis.

Factors affecting the laser processing of wood, 2: Effects of material parameters on machinability

International Nuclear Information System (INIS)

Arai, T.; Hayashi, D.

1994-01-01

Material parameters of wood were investigated. Factors relating to the workpiece include cutting direction, specific gravity, and components of the wood such as resin-like materials. Also studies of the effects of irregular tissue on machinability were made. The interactions between laser beam and materials are often greatly complex. They depend on the characteristics of the laser beam, the thermal constants of the woods, and the optical surface properties of the woods. Therefore, high quality beam mode and carefully selected materials were used. The following laser cutting properties became clear after studying the experimental results. Slow speed cutting and softwoods make slight differences, regarding cutting section and fiber direction. However, it can beconsidered that there is not very much change except in cross-section. Because of the high power density of laser, cutting speed makes no big difference. The irregular tissue of wood cannot maintain normal cutting speed and accuracy. The factor of genuine density eta, which is thought to be entirely independent of each specific gravity, is definedas the concept of density in general. It can be obtained by applying a simple rule, that is, the eta is the ratio of r(u)/rho(s) where rho(s) is the wood substance as the characteristic value of wood, and r(u)is specific gravity. An experimental formula shows that the depth of cut decreases in proportion to the value of eta. However, in the strict sense of the word, data of wood material as a natural resources mustbe treated qualitatively, because there are deviations from regularity due to various reasons. (author)

Effects of extractives and ash on natural resistance of four woods to xylophogous termites

Directory of Open Access Journals (Sweden)

Juarez Benigno Paes

2013-09-01

Full Text Available This study tested the natural resistance of wood of four tree species to Nasutitermes corniger Motsch. xylophogous termite attack and correlate the resistance with the amount of extract and ash in the chemical composition of the tested species. The species evaluated were Anadenanthera colubrina (Vell. Brenan. var. cebil (Gris. Alts., Tabebuia aurea (Mart. Bureau., Amburana cearensis (Allem. A.C.Sm. and Eucalyptus camaldulensis Dehnh. Test samples with dimensions of 2.00 x 10.16 x 0.64 cm (radial x longitudinal x tangential were obtained at two positions (external heartwood and sapwood of each species. The samples were exposed to action of termites for 45 days in food preference assay. The content of wood extractives was obtained through the sawdust that went through sieve of 40 mesh and were retained in the 60 mesh. The natural resistance was not associated with wood extractive contents. The wood more resistant to termite attack was the Anadenanthera colubrina var. cebil in the two positions (external heartwood and sapwood and Eucalyptus camaldulensis wood presented the greatest wear. The biological resistance of wood was correlated with ash content, i.e., the species with the highest levels was the most resistant to termite attack.

Mechanical Properties of Isotactic Polypropylene Modified with Thermoplastic Potato Starch

Science.gov (United States)

Knitter, M.; Dobrzyńska-Mizera, M.

2015-05-01

In this paper selected mechanical properties of isotactic polypropylene (iPP) modified with potato starch have been presented. Thermoplastic starch (TPS) used as a modifier in the study was produced from potato starch modified with glycerol. Isotactic polypropylene/thermoplastic potato starch composites (iPP/TPS) that contained 10, 30, 50 wt.% of modified starch were examined using dynamic mechanical-thermal analysis, static tensile, Brinell hardness, and Charpy impact test. The studies indicated a distinct influence of a filler content on the mechanical properties of composites in comparison with non-modified polypropylene.

The tensile strength test of thermoplastic materials based on poly(butylene terephtalate

Directory of Open Access Journals (Sweden)

Rzepecka Anna

2017-01-01

Full Text Available Thermoplastic composites go toward making an increasingly greater percentage of all manufacturing polymer composites. They have a lot of beneficial properties and their manufacturing using injecting and extrusion methods is a very easy and cheap process. Their properties significantly overtake the properties of traditional materials and it is the reason for their use. Scientists are continuously carrying out research to find new applications of composites materials in new industries, not only in the automotive or aircraft industry. When thermoplastic composites are manufactured a very important factor is the appropriate accommodation of tensile strength to their predestination. Scientists need to know the behaviour of these materials during the impact of different forces, and the factors of working in normal conditions too. The main aim of this article was macroscopic and microscopic analysis of the structure of thermoplastic composites after static tensile strength test. Materials which were analysed were thermoplastic materials which have poly(butylene terephthalate – PBT matrix reinforced with different content glass fibres – from 10% for 30%. In addition, research showed the necessary force to receive fracture and set their distinguishing characteristic down.

Laboratory evaluations of woods from Pakistan and their extractives against Postia placenta and Trametes versicolor

Science.gov (United States)

Mark Mankowski; Barbar Hassan; Amy Blodgett; Grant T. Kirker

2016-01-01

Natural durable wood species are those which exhibit innate tolerance to wood decay organisms such as fungi and termites. The goal of this study was to evaluate 4 wood species (Dalbergia sissoo, Cedrus deodara, Morus alba and Pinus roxburghii) from Pakistan in order to determine their resistance to both a model brown (

Characterization of thermoplastic composites for hot stamp forming

NARCIS (Netherlands)

Rietman, Bert; Grouve, Wouter; Akkerman, Remko

2014-01-01

This paper describes state-of-the-art characterization methods for thermoplastic composites at high processing temperature and provides a few examples of application in simulations of the hot stamp forming process.

Ecological trends in the wood anatomy of Vaccinioideae (Ericaceae s.l.)

NARCIS (Netherlands)

Lens, F.; Luteyn, J.L.; Smets, E.; Jansen, S.

2004-01-01

The ecological wood anatomy of 128 vaccinioid wood samples (including 115 species, 35 genera), collected between 39°S and 60°N latitude and 10 m to 3400 m altitude is studied. Several wood anatomical features within the subfamily, viz. tangential vessel diameter, average length of tracheary

Viscous and thermal modelling of thermoplastic composites forming process

Science.gov (United States)

Guzman, Eduardo; Liang, Biao; Hamila, Nahiene; Boisse, Philippe

2016-10-01

Thermoforming thermoplastic prepregs is a fast manufacturing process. It is suitable for automotive composite parts manufacturing. The simulation of thermoplastic prepreg forming is achieved by alternate thermal and mechanical analyses. The thermal properties are obtained from a mesoscopic analysis and a homogenization procedure. The forming simulation is based on a viscous-hyperelastic approach. The thermal simulations define the coefficients of the mechanical model that depend on the temperature. The forming simulations modify the boundary conditions and the internal geometry of the thermal analyses. The comparison of the simulation with an experimental thermoforming of a part representative of automotive applications shows the efficiency of the approach.

Bending behavior of thermoplastic composite sheets viscoelasticity and temperature dependency in the draping process

CERN Document Server

Ropers, Steffen

2017-01-01

Within the scope of this work, Steffen Ropers evaluates the viscoelastic and temperature-dependent nature of the bending behavior of thermoplastic composite sheets in order to further enhance the predictability of the draping simulation. This simulation is a useful tool for the development of robust large scale processes for continuously fiber-reinforced polymers (CFRP). The bending behavior thereby largely influences the size and position of wrinkles, which are one of the most common processing defects for continuously fiber-reinforced parts. Thus, a better understanding of the bending behavior of thermoplastic composite sheets as well as an appropriate testing method along with corresponding material models contribute to a wide-spread application of CFRPs in large scale production. Contents Thermoplastic Prepregs Draping Simulation of Thermoplastic Prepregs Bending Characterization of Textile Composites Modeling of Bending Behavior Target Groups Researchers and students in the field of polymer, lightweight,...

Use of Melt Flow Rate Test in Reliability Study of Thermoplastic Encapsulation Materials in Photovoltaic Modules

Energy Technology Data Exchange (ETDEWEB)

Moseley, J.; Miller, D.; Shah, Q.-U.-A. S. J.; Sakurai, K.; Kempe, M.; Tamizhmani, G.; Kurtz, S.

2011-10-01

Use of thermoplastic materials as encapsulants in photovoltaic (PV) modules presents a potential concern in terms of high temperature creep, which should be evaluated before thermoplastics are qualified for use in the field. Historically, the issue of creep has been avoided by using thermosetting polymers as encapsulants, such as crosslinked ethylene-co-vinyl acetate (EVA). Because they lack crosslinked networks, however, thermoplastics may be subject to phase transitions and visco-elastic flow at the temperatures and mechanical stresses encountered by modules in the field, creating the potential for a number of reliability and safety issues. Thermoplastic materials investigated in this study include PV-grade uncured-EVA (without curing agents and therefore not crosslinked); polyvinyl butyral (PVB); thermoplastic polyurethane (TPU); and three polyolefins (PO), which have been proposed for use as PV encapsulation. Two approaches were used to evaluate the performance of these materials as encapsulants: module-level testing and a material-level testing.

Photoinitiated grafting of porous polymer monoliths and thermoplastic polymers for microfluidic devices

Science.gov (United States)

Frechet, Jean M. J. [Oakland, CA; Svec, Frantisek [Alameda, CA; Rohr, Thomas [Leiden, NL

2008-10-07

A microfluidic device preferably made of a thermoplastic polymer that includes a channel or a multiplicity of channels whose surfaces are modified by photografting. The device further includes a porous polymer monolith prepared via UV initiated polymerization within the channel, and functionalization of the pore surface of the monolith using photografting. Processes for making such surface modifications of thermoplastic polymers and porous polymer monoliths are set forth.

One-pot synthesis of thermoplastic mixed paramylon esters using trifluoroacetic anhydride.

Science.gov (United States)

Shibakami, Motonari; Tsubouchi, Gen; Sohma, Mitsugu; Hayashi, Masahiro

2015-03-30

Mixed paramylon esters prepared from paramylon (a storage polysaccharide of Euglena), acetic acid, and a long-chain fatty acid by one-pot synthesis using trifluoroacetic anhydride as a promoter and solvent were shown to have thermoplasticity. Size exclusion chromatography indicated that the mixed paramylon esters had a weight average molecular weight of approximately 4.9-6.7×10(5). Thermal analysis showed that these esters were stable in terms of the glass transition temperature (>90°C) and 5% weight loss temperature (>320°C). The degree of substitution of the long alkyl chain group, a dominant factor determining thermoplasticity, was controlled by tuning the feed molar ratio of acetic acid and long-chain fatty acid to paramylon. These results implied that the one-pot synthesis is useful for preparing structurally-well defined thermoplastic mixed paramylon esters with high molecular weight. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effect of natural fibres on the mechanical properties of thermoplastic starch

Science.gov (United States)

Oniszczuk, Tomasz; Wójtowicz, Agnieszka; Moácicki, Leszek; Mitrus, Marcin; Kupryaniuk, Karol; Kusz, Andrzej; Bartnik, Grzegorz

2016-04-01

This paper presents the results covering the mechanical properties of thermoplastic potato starch granules with flax, cellulose fibre, and pine bark addition. A modified single screw extrusion-cooker TS-45 with L/D = 18 and an additional cooling section of the barrel was used as the processing unit. The establishment influence of the fibre addition, as well as the extrusion-cooker screw speed, on the mechanical properties of the thermoplastic starch granules was the main objective of the investigation. The maximum force during compression to 50% of the sample diameter, elastic modulus, and compression strength were evaluated. Significant differences were noted depending on the amount of fibre used, while only an insignificant influence of screw speed on the mechanical properties of the granulate was reported. An increased amount of fibres lowered the maximum force as well as the elastic modulus and compression strength of the thermoplastic starch granulates.

A Study on the Effect of Plasma Treatment for Waste Wood Biocomposites

Directory of Open Access Journals (Sweden)

MiMi Kim

2013-01-01

Full Text Available The surface modification of wood powder by atmospheric pressure plasma treatment was investigated. The composites were manufactured using wood powder and polypropylene (wood powder: polypropylene = 55 wt% : 45 wt%. Atmospheric pressure plasma treatment was applied under the condition of 3 KV, 17±1 KHz, 2 g/min. Helium was used as the carrier gas and hexamethyl-disiloxane (HMDSO as the monomer to modify the surface property of the waste wood biocomposites by plasma polymerization. The tensile strengths of untreated waste wood powder (W3 and single species wood powder (S3 were about 18.5 MPa and 21.5 MPa while those of plasma treated waste wood powder (PW3 and plasma treated single species wood powder (PS3 were about 21.2 MPa and 23.4 MPa, respectively. Tensile strengths of W3 and S3 were improved by 14.6% and 8.8%, respectively. From the analyses of mechanical properties and morphology, we conclude that the interfacial bonding of polypropylene and wood powder can be improved by atmospheric pressure plasma treatment.

Scarcity on the market for wood wastes

International Nuclear Information System (INIS)

De Boer, A.

2004-01-01

An overview is given of the market for wood wastes in the Netherlands and how this affects the targets to use biomass. Several types of biomass must be imported, not only wood wastes, but also e.g. olive stones and cacao shells [nl

Processing of thermoplastic polymers using reactive solvents

NARCIS (Netherlands)

Meijer, H.E.H.; Venderbosch, R.W.; Goossens, J.G.P.; Lemstra, P.J.

1996-01-01

The use of reactive solvents offers an interesting and flexible route to extent the processing characteristics of thermoplastic polymers beyond their existing limits. This holds for both intractable and tractable polymers. The first mainly applies for amorphous high-Tg polymers where processing may

Thermoplastic starch materials prepared from rice starch; Preparacao e caracterizacao de materiais termoplasticos preparados a partir de amido de arroz

Energy Technology Data Exchange (ETDEWEB)

Pontes, Barbara R.B.; Curvelo, Antonio A.S., E-mail: barbarapont@gmail.co [Universidade de Sao Paulo (IQSC/USP), Sao Carlos, SP (Brazil). Inst. de Quimica

2009-07-01

Rice starch is a source still little studied for the preparation of thermoplastic materials. However, its characteristics, such as the presence of proteins, fats and fibers may turn into thermoplastics with a better performance. The present study intends the evaluation of the viability of making starch thermoplastic from rice starch and glycerol as plasticizer. The results of X-ray diffraction and scanning electronic microscopy demonstrate the thermoplastic acquisition. The increase of plasticizer content brings on more hydrophilic thermoplastics with less resistance to tension and elongation at break. (author)

PHYSICAL AND MECHANICAL PROPERTIES OF JUVENILE Schizolobium amazonicum WOOD

Directory of Open Access Journals (Sweden)

Graziela Baptista Vidaurre

2018-03-01

Full Text Available ABSTRACT Growth in world demand for wood implies a search for new fast growing species with silvicultural potential, and in this scenario for native species such as Paricá . Thus, the objective of this study was determining the physical and mechanical wood properties of the Schizolobium amazonicum species (known as Paricá in Brazil. Trees were collected from commercial plantations located in the north of Brazil with ages of 5, 7, 9 and 11 years. Four logs from trees of each age in the longitudinal direction of the trees were obtained, and later a diametrical plank of each log was taken to manufacture the specimens which were used to evaluate some physical and mechanical properties of the wood. The basic density of Paricá was reduced in the basetop direction and no difference between the radial positions was observed, while the average basic density of this wood was characterized as low. The region close to the bark showed less longitudinal contraction and also greater homogeneity of this property along the trunk, while for tangential contraction the smallest variation was found in the region near the pith. Paricá wood contraction was characterized as low. Age influenced most of the mechanical properties, where logs from the base had the highest values of mechanical strength.

Pyrolysis characteristics of typical biomass thermoplastic composites

Directory of Open Access Journals (Sweden)

Hongzhen Cai

Full Text Available The biomass thermoplastic composites were prepared by extrusion molding method with poplar flour, rice husk, cotton stalk and corn stalk. The thermo gravimetric analyzer (TGA has also been used for evaluating the pyrolysis process of the composites. The results showed that the pyrolysis process mainly consists of two stages: biomass pyrolysis and the plastic pyrolysis. The increase of biomass content in the composite raised the first stage pyrolysis peak temperature. However, the carbon residue was reduced and the pyrolysis efficiency was better because of synergistic effect of biomass and plastic. The composite with different kinds of biomass have similar pyrolysis process, and the pyrolysis efficiency of the composite with corn stalk was best. The calcium carbonate could inhibit pyrolysis process and increase the first stage pyrolysis peak temperature and carbon residue as a filling material of the composite. Keywords: Biomass thermoplastic composite, Calcium carbonate, Pyrolysis characteristic

Development of a pathway model to assess the exposure of European pine trees to pine wood nematode via the trade of wood

NARCIS (Netherlands)

Douma, J.C.; Werf, Van Der W.; Hemerik, L.; Magnusson, C.; Robinet, C.

2017-01-01

Pine wood nematode (PWN), Bursaphelenchus xylophilus, is a threat for pine species (Pinus spp.) throughout the world. The nematode is native to North America, and invaded Japan, China, Korea, and Taiwan, and more recently Portugal and Spain. PWN enters new areas through trade in wood products. Once

Accuracy of Implants Placed with Surgical Guides: Thermoplastic Versus 3D Printed.

Science.gov (United States)

Bell, Caitlyn K; Sahl, Erik F; Kim, Yoon Jeong; Rice, Dwight D

This study was conducted to evaluate the accuracy of implants placed using two different guided implant surgery materials: thermoplastic versus three-dimensionally (3D) printed. A cone beam computed tomography (CBCT) scan previously obtained and selected for single-tooth implant replacement was converted into a Digital Imaging and Communications in Medicine (DICOM) file. All models were planned and exported for printing using BlueSkyBio Plan Software with the DICOM files. A total of 20 3D-printed mandibular quadrant jaws replicating the CBCT were printed by Right Choice Milling, as was the control model to accept the control implant. Previously, 10 thermoplastic and 10 3D-printed surgical guides had been made by the same lab technician at Right Choice Milling. One Nobel Biocare implant with a trilobe connection was placed per guide and replica jaw model pair. Implants were placed using the thermoplastic and 3D-printed surgical guides, representing the two test groups, following the Nobel Biocare guided surgical protocol. A total of 21 CBCT scans were then taken, one for the control implant and one for each test implant. The CBCT volume was converted to a DICOM file and transferred to Invivo5 software version 5.4 (Anatomage). The DICOM file of each test implant was superimposed over the DICOM file of the control. The deviation of the head of the implant, the deviation of the apex of the implant, and the angle of deviation were evaluated from measurements on the superimposition of the control and test implants. Mann-Whitney U test was used to test the null hypotheses at α = .05 and a confidence interval of 95%. Descriptive statistics were used for the average ± standard deviation. The implants placed with the thermoplastic surgical guides showed an average of 3.40 degrees of angular deviation compared to 2.36 degrees for implants placed with the 3D-printed surgical guides (P = .143). The implants placed with the thermoplastic surgical guides showed an average of 1

Vertical variations in wood CO2 efflux for live emergent trees in a Bornean tropical rainforest.

Science.gov (United States)

Katayama, Ayumi; Kume, Tomonori; Komatsu, Hikaru; Ohashi, Mizue; Matsumoto, Kazuho; Ichihashi, Ryuji; Kumagai, Tomo'omi; Otsuki, Kyoichi

2014-05-01

Difficult access to 40-m-tall emergent trees in tropical rainforests has resulted in a lack of data related to vertical variations in wood CO2 efflux, even though significant variations in wood CO2 efflux are an important source of errors when estimating whole-tree total wood CO2 efflux. This study aimed to clarify vertical variations in wood CO2 efflux for emergent trees and to document the impact of the variations on the whole-tree estimates of stem and branch CO2 efflux. First, we measured wood CO2 efflux and factors related to tree morphology and environment for seven live emergent trees of two dipterocarp species at four to seven heights of up to ∼ 40 m for each tree using ladders and a crane. No systematic tendencies in vertical variations were observed for all the trees. Wood CO2 efflux was not affected by stem and air temperature, stem diameter, stem height or stem growth. The ratios of wood CO2 efflux at the treetop to that at breast height were larger in emergent trees with relatively smaller diameters at breast height. Second, we compared whole-tree stem CO2 efflux estimates using vertical measurements with those based on solely breast height measurements. We found similar whole-tree stem CO2 efflux estimates regardless of the patterns of vertical variations in CO2 efflux because the surface area in the canopy, where wood CO2 efflux often differed from that at breast height, was very small compared with that at low stem heights, resulting in little effect of the vertical variations on the estimate. Additionally, whole-tree branch CO2 efflux estimates using measured wood CO2 efflux in the canopy were considerably different from those measured using only breast height measurements. Uncertainties in wood CO2 efflux in the canopy did not cause any bias in stem CO2 efflux scaling, but affected branch CO2 efflux. © The Author 2014. Published by Oxford University Press. All rights reserved.

Wood Permeability in Eucalyptus grandis and Eucalyptus dunnii

Directory of Open Access Journals (Sweden)

Raphael Nogueira Rezende

2017-12-01

Full Text Available ABSTRACT The objective of this study was to evaluate the flow of air and water in Eucalyptus grandis and Eucalyptus dunnii wood. Wood was collected from four trees aged 37 years in an experimental plantation of the Federal University of Lavras, Brazil. Planks were cut off the basal logs to produce specimens for air and water permeability testing. Results indicated that the longitudinal permeability to air and water of E. grandis wood were, on average, 5% and 10% higher, respectively, than that of E. dunnii wood. E. grandis and E. dunnii wood showed neither air nor water flow in the test for permeability transversal to the fibers, and longitudinal permeability to air exceeded that to water by approximately 50 fold in both species.

Classification of CITES-listed and other neotropical Meliaceae wood images using convolutional neural networks.

Science.gov (United States)

Ravindran, Prabu; Costa, Adriana; Soares, Richard; Wiedenhoeft, Alex C

2018-01-01

The current state-of-the-art for field wood identification to combat illegal logging relies on experienced practitioners using hand lenses, specialized identification keys, atlases of woods, and field manuals. Accumulation of this expertise is time-consuming and access to training is relatively rare compared to the international demand for field wood identification. A reliable, consistent and cost effective field screening method is necessary for effective global scale enforcement of international treaties such as the Convention on the International Trade in Endagered Species (CITES) or national laws (e.g. the US Lacey Act) governing timber trade and imports. We present highly effective computer vision classification models, based on deep convolutional neural networks, trained via transfer learning, to identify the woods of 10 neotropical species in the family Meliaceae, including CITES-listed Swietenia macrophylla , Swietenia mahagoni , Cedrela fissilis , and Cedrela odorata . We build and evaluate models to classify the 10 woods at the species and genus levels, with image-level model accuracy ranging from 87.4 to 97.5%, with the strongest performance by the genus-level model. Misclassified images are attributed to classes consistent with traditional wood anatomical results, and our species-level accuracy greatly exceeds the resolution of traditional wood identification. The end-to-end trained image classifiers that we present discriminate the woods based on digital images of the transverse surface of solid wood blocks, which are surfaces and images that can be prepared and captured in the field. Hence this work represents a strong proof-of-concept for using computer vision and convolutional neural networks to develop practical models for field screening timber and wood products to combat illegal logging.

3D modeling of squeeze flow of unidirectionally thermoplastic composite inserts

Science.gov (United States)

Ghnatios, Chady; Abisset-Chavanne, Emmanuelle; Binetruy, Christophe; Chinesta, Francisco; Advani, Suresh

2016-10-01

Thermoplastic composites are attractive because they can be recycled and exhibit superior mechanical properties. The ability of thermoplastic resin to melt and solidify allows for fast and cost-effective manufacturing processes, which is a crucial property for high volume production. Thermoplastic composite parts are usually obtained by stacking several prepreg plies to create a laminate with a particular orientation sequence to meet design requirements. During the consolidation and forming process, the thermoplastic laminate is subjected to complex deformation which can include intraply and/or interply shear, ply reorientation and squeeze flow. In the case of unidirectional prepregs, the ply constitutive equation, when elastic effects are neglected, can be modeled as a transversally isotropic fluid, that must satisfy the fiber inextensibility as well as the fluid incompressibility. The high-fidelity solution of the squeeze flow in laminates composed of unidirectional prepregs was addressed in our former works by making use of an in-plane-out-of-plane separated representation allowing a very detailed resolution of the involved fields throughout the laminate thickness. In the present work prepregs plies are supposed of limited dimensions compared to the in-plane dimension of the part and will be named inserts. Again within the Proper Generalized Decomposition framework high-resolution simulation of the squeeze flow occurring during consolidation is addressed within a fully 3D in-plane-out-of-plane separated representation.

Production of palm frond based wood plastic composite by using twin screw extruder

Science.gov (United States)

Russita, M.; Bahruddin

2018-04-01

Wood plastic composite (WPC) is the blending product from wood as filler and polymer thermoplastic as matric. Palm frond waste is a material with selulose about 68%, so it has potential to be developed as raw material for WPC. The purpose of this research was to learn how to produce WPC based on palm frond use twin screw extruder. It used popropilen as matric. As for aditif, it used Maleated Polypropilene (MAPP) as compatibilizer and paraffin as plasticizer. The size of palm frond is 40 – 80 mesh. WPC is made from blending polipropylene, palm frond, MAPP and paraffin with dry mixing method in room temperature. Then, PP, Palm frond and additive from dry mixing is fed into twin screw extruder at 190°C and 60 rpm. It use palm frond/polypropylene 60/40, MAPP 5% w/w and paraffin 2% w/w. From the result, it shown that WPC based on palm frond met the standards forcommercial WPC. It has tensile strength up to 19.2 MPa, bending strength 43.6 MPa and water adsorption 0,32% w/w. So, WPC based on palm frond has prospective to be developed for commercial WPC.

EFFECT OF ARTIFICIAL WEATHERING ON WOOD LAMINATES COLOR TREATED WITH TWO FINISHING PRODUCTS

Directory of Open Access Journals (Sweden)

Thais Jacob Mendes

2016-03-01

Full Text Available Weathering is one of the main reasons for the degradation of wood, especially its color. The application of finishes minimizes these effects. This study aimed to monitor the effect of artificial weathering on wood veneer of the species cumaru (Dipteryx odorata and pau marfim (Balfourodendron riedelianum with two finishes, the marine varnish and Cetol, with monitoring using a spectrophotometer. The samples were subjected to cycles of exposure to weathering for 20, 40, 52, 76, 124, 226, 430, 838 and 960 hours. The colorimetric parameters (L*, a*, b*, C and h* were measured before treatment, after application of the products and during the weathering time intervals. The application of finishes darkened veneer of cumaru wood and pau marfim in nature. However, in higher weathering times, both species returned to a lighter color, and even became lighter than the natural wood. The use of Cetol was more efficient, giving greater stability in the conservation of wood color of the species studied.

Thermoplastic elastomers via controlled radical graft polymerization

NARCIS (Netherlands)

Tuzcu, G.

2012-01-01

Rubbery behavior with a consistent modulus over a wide temperature range is a challenge in the search for ultimate structure-property relations of thermoplastic elastomers (TPEs). This feature is closely related to the phase separation behavior of the constitutional segments and the Tg of the

Low-NO{sub x}, wood chip combustion

Energy Technology Data Exchange (ETDEWEB)

Saastamoinen, J.; Oravainen, H.; Haemaelaeinen, J.; Paakkinen, K. [VTT Energy, Jyvaeskylae (Finland)

1997-10-01

The regulations for nitrogen oxide emissions vary in different countries, but the general trend in the future will probably be that the emissions limits will be lowered also for wood combustion plants, which are small or medium size units. Thus, the development of wood chip burning furnaces (grate furnaces, fluidized bed combustors, stoker furnaces) with lower nitrogen oxide emissions, is important. The wood used in the combustor, its particle size, moisture and fuel properties (nitrogen content) affect the nitrogen emissions. The nitrogen oxide release is also much affected by the design and operation of the combustor (air staging, fuel air preheat, flue gas circulation, air to fuel mass ratio). The fate of nitrogen compounds originally in the virgin wood depends much on the design of the combustor system and by proper planning it is possible to reduce the emission of nitrogen oxides. Basic knowledge of the release of nitrogen compounds from single wood particles is attained. The release of gaseous nitrogen compounds from wood particles during pyrolysis and combustion is studied experimentally and by modelling. Nitrogen release is studied experimentally by two ways, by analysing the gas and by quenching the particle and analysing the char residue. Formation of nitrogen oxide emissions in a fuel bed is studied by modelling and by combustion experiments with a pot furnace. This research gives general information of nitrogen oxide formation in wood bunting especially in fixed beds. The development of a horizontal stoker burner for wood chips with low emissions is the practical aim of the research. (orig.)

The effect of cocoa (Theobroma cacao L on the basic color stability of thermoplastic nylon resin dentures

Directory of Open Access Journals (Sweden)

Amiyatun Naini

2011-11-01

Full Text Available Nylon thermoplastic resin is material of choice for the making of flexible. This denture do not use wire retention, but has the physical properties of water absorption. In the oral cavity, it will always be in contact with food and beverages consumed. One of the foods that are consumed by the public is chocolate. This study aimed to determine the effect of cocoa (Theobroma cacao L on color stability of the thermoplastic nylon denture base. The study sample was thermoplastic nylon (valplast with a size of 10x10x2 mm soaked in the chocolate solution for 7 and 14 days. As the control, the sample soaked with distilled water. The color testing stability used was densitometer. There were significant differences between the control group (distilled water and the chocolate solution. This was due to dissolved components/tannin having a capillary flow diffusion into thermoplastic nylons that causing discoloration. The conclusion of this study, there was the effect of cocoa (Theobroma cacao L against the color stability of the nylon thermoplastic denture base. The longer time of immersion of nylon thermoplastic the greater the change in color.

Evaluation of wood species and preservatives for Wisconsin transportation sign posts : [research brief].

Science.gov (United States)

2013-12-01

The Wisconsin Department of Transportation (WisDOT) administers approximately 11,800 miles of state highways. It uses preservative-treated wood posts for much of the signage along these highways because wood is relatively inexpensive, easy to install...

Wood decomposition as influenced by invertebrates

Science.gov (United States)

Michael D. Ulyshen

2014-01-01

The diversity and habitat requirements of invertebrates associated with dead wood have been the subjects of hundreds of studies in recent years but we still know very little about the ecological or economic importance of these organisms. The purpose of this review is to examine whether, how and to what extent invertebrates affect wood decomposition in terrestrial...

Termites and flooding affect microbial communities in decomposing wood

Science.gov (United States)

Michael D. Ulyshen; Susan V. Diehl; Dragica Jeremic

2016-01-01

Wood properties and microbial community characteristics were compared between loblolly pine (Pinus taeda L.) logs protected or unprotected from termites (Blattodea: Rhinotermitidae: Reticulitermes spp.) and other arthropods for two years in seasonally flooded and unflooded forests in the southeastern United States. Significant compositional differences were observed...

Determination of mass attenuation coefficient in wood and leaves of typical trees by gamma-ray attenuation technique

International Nuclear Information System (INIS)

Miranda, Regina M. de; Pascholati, Elisabete M.

1997-01-01

Using an 241 Am source the mass attenuation coefficient of different woods and leaves of typical species of the Atlantic Forest were measured. The results for natural wood, dry wood and dry leaves indicate that the variation is very small among different species. However, woods present a higher attenuation than leaves, both depending on their water content. (author). 10 refs., 3 figs., 1 tab

Portable Device Slices Thermoplastic Prepregs

Science.gov (United States)

Taylor, Beverly A.; Boston, Morton W.; Wilson, Maywood L.

1993-01-01

Prepreg slitter designed to slit various widths rapidly by use of slicing bar holding several blades, each capable of slicing strip of preset width in single pass. Produces material evenly sliced and does not contain jagged edges. Used for various applications in such batch processes involving composite materials as press molding and autoclaving, and in such continuous processes as pultrusion. Useful to all manufacturers of thermoplastic composites, and in slicing B-staged thermoset composites.

Attribute Based Selection of Thermoplastic Resin for Vacuum Infusion Process: A Decision Making Methodology

DEFF Research Database (Denmark)

Raghavalu Thirumalai, Durai Prabhakaran; Lystrup, Aage; Løgstrup Andersen, Tom

2012-01-01

The composite industry looks toward a new material system (resins) based on thermoplastic polymers for the vacuum infusion process, similar to the infusion process using thermosetting polymers. A large number of thermoplastics are available in the market with a variety of properties suitable...... be beneficial. In this paper, the authors introduce a new decision making tool for resin selection based on significant attributes. This article provides a broad overview of suitable thermoplastic material systems for vacuum infusion process available in today’s market. An illustrative example—resin selection...... for vacuum infused of a wind turbine blade—is shown to demonstrate the intricacies involved in the proposed methodology for resin selection....

Examination of injection moulded thermoplastic maize starch

Directory of Open Access Journals (Sweden)

2007-12-01

Full Text Available This paper focuses on the effect of the different injection moulding parameters and storing methods on injection moulded thermoplastic maize starch (TPS. The glycerol and water plasticized starch was processed in a twin screw extruder and then with an injection moulding machine to produce TPS dumbbell specimens. Different injection moulding set-ups and storing conditions were used to analyse the effects on the properties of thermoplastic starch. Investigated parameters were injection moulding pressure, holding pressure, and for the storage: storage at 50% relative humidity, and under ambient conditions. After processing the mechanical and shrinkage properties of the manufactured TPS were determined as a function of the ageing time. While conditioning, the characteristics of the TPS changed from a soft material to a rigid material. Although this main behaviour remained, the different injection moulding parameters changed the characteristics of TPS. Scanning electron microscope observations revealed the changes in the material on ageing.

Wood anatomy of the neotropical Sapotaceae. VI, Chloroluma

Science.gov (United States)

B. F. Kukachka

1978-01-01

The old genus Chloroluma has been reinstated to generic status after having been in synonomy under Chrysophyllum for many years. The description is based on the type species C. gonocarpa which is characterized by: Its clear yellow wood; pores in radial-echelon arrangement; rhombic, two-sized, and microcrystals frequent in the axial parenchyma and wood rays; colored...

A new method of determining moisture gradient in wood

Science.gov (United States)

Zhiyong Cai

2008-01-01

Moisture gradient in wood and wood composites is one of most important factors that affects both physical stability and mechanical performance. This paper describes a method for measuring moisture gradient in lumber and engineering wood composites as it varies across material thickness. This innovative method employs a collimated radiation beam (x rays or [gamma] rays...

Irradiation effects in wood and cellulose

International Nuclear Information System (INIS)

McLaren, K.G.

1976-01-01

For cellulosic materials the predominant effect of high energy radiation is depolymerisation and degradation by chain scission, although there is some evidence that crosslinking or cellulose stabilisation can occur under certain conditions. When the cellulose is in the form of a natural product such as wood, where it is intimately associated with other polysaccharides, lignins, resins and gums, the effects of radiation can be significantly modified. Examination of cellulose produced by chemical pulping treatment of wood which had been previously given small doses of radiation, showed significant differences in the extent of cellulose depolymerisation with different wood species. The relevance of this work to the paper pulp industry will also be discussed. (author)

Decay of oak Wood provoked by fungus Stereum hirsutum (Willd. ex Fr. S. F. Gray. and its' essential physiological requirements

Directory of Open Access Journals (Sweden)

Mirić Milenko

2005-01-01

Full Text Available White rot fungi usually decompose cell walls of attacked wood destroying tissue elements (i.e. parenchyma cells, wood fibres, tension wood, tracheas etc in different amount, depending to wood-species as well as to its' zones. Different fungi secrete specific enzymes that are responsible for certain damages. As consequence, the wood structure use to be significantly and unfixable decomposed and changed. Microscopical analyses that have been run provided clear and indicative information relating to effects of fungal activity on wood tissue. Physiological requirements of fungi are for shore of the highest importance in understanding of mechanism of decaying process in the wood. The most important factors as like temperature and concentration of H ions, as well as main nutrients as sources of carbon, nitrogen and phosphorus can affect the behaviour of wood decaying fungi. The impacts of these factors on the growth and production on mycelial mass of Stereum hirsutum (Willd. ex Fr. S.F. Gray., have been investigated. This fungus is one of the most frequent appearing on the Sessile- and Pedunculate Oak weakened trees or felled logs, behaving as parasite as well as saprophyte. As a causer of Oak sapwood white rot S. hirsutum causes significant damages of wood at forest- as well as at industrial storages.

Network analysis reveals ecological links between N-fixing bacteria and wood-decaying fungi.

Science.gov (United States)

Hoppe, Björn; Kahl, Tiemo; Karasch, Peter; Wubet, Tesfaye; Bauhus, Jürgen; Buscot, François; Krüger, Dirk

2014-01-01

Nitrogen availability in dead wood is highly restricted and associations with N-fixing bacteria are thought to enable wood-decaying fungi to meet their nitrogen requirements for vegetative and generative growth. We assessed the diversity of nifH (dinitrogenase reductase) genes in dead wood of the common temperate tree species Fagus sylvatica and Picea abies from differently managed forest plots in Germany using molecular tools. By incorporating these genes into a large compilation of published nifH sequences and subsequent phylogenetic analyses of deduced proteins we verified the presence of diverse pools corresponding to functional nifH, almost all of which are new to science. The distribution of nifH genes strongly correlated with tree species and decay class, but not with forest management, while higher fungal fructification was correlated with decreasing nitrogen content of the dead wood and positively correlated with nifH diversity, especially during the intermediate stage of wood decay. Network analyses based on non-random species co-occurrence patterns revealed interactions among fungi and N-fixing bacteria in the dead wood and strongly indicate the occurrence of at least commensal relationships between these taxa.

Network analysis reveals ecological links between N-fixing bacteria and wood-decaying fungi.

Directory of Open Access Journals (Sweden)

Björn Hoppe

Full Text Available Nitrogen availability in dead wood is highly restricted and associations with N-fixing bacteria are thought to enable wood-decaying fungi to meet their nitrogen requirements for vegetative and generative growth. We assessed the diversity of nifH (dinitrogenase reductase genes in dead wood of the common temperate tree species Fagus sylvatica and Picea abies from differently managed forest plots in Germany using molecular tools. By incorporating these genes into a large compilation of published nifH sequences and subsequent phylogenetic analyses of deduced proteins we verified the presence of diverse pools corresponding to functional nifH, almost all of which are new to science. The distribution of nifH genes strongly correlated with tree species and decay class, but not with forest management, while higher fungal fructification was correlated with decreasing nitrogen content of the dead wood and positively correlated with nifH diversity, especially during the intermediate stage of wood decay. Network analyses based on non-random species co-occurrence patterns revealed interactions among fungi and N-fixing bacteria in the dead wood and strongly indicate the occurrence of at least commensal relationships between these taxa.

TOTAL WOOD VOLUME ESTIMATION OF EUCALYPTUS SPECIES BY IMAGES OF LANDSAT SATELLITE

Directory of Open Access Journals (Sweden)

Elias Fernando Berra

2012-12-01

Full Text Available http://dx.doi.org/10.5902/198050987566Models relating spectral answers with biophysical parameters aim estimate variables, like wood volume, without the necessity of frequent field measurements. The objective was to develop models to estimate wood volume by Landsat 5 TM images, supported by regional forest inventory data. The image was geo-referenced and converted to spectral reflectance. After, the images-index NDVI (Normalized Difference Vegetation Index and SR (Simple Ratio was generated. The reflectance values of the bands (TM1, TM2, TM3 e TM4 and of the indices (NDVI and SR was related with the wood volume. The biggest correlation with volume was with the NDVI and SR indices. The variables selection was made by Stepwise method, which returned three regression models as significant to explain the variation in volume. Finally, the best fitted model was selected (volume = -830,95 + 46,05 (SR + 107,47 (TM2, which was applied on the Landsat image where the pixels had started to represent the estimated volume in m³/ha on the Eucalyptus sp. production units. This model, significant at 95% confidence level, explains 68% of the wood volume variation.

Thermoplastic film camera for holographic recording

International Nuclear Information System (INIS)

Liegeois, C.; Meyrueis, P.

1982-01-01

The design thermoplastic-film recording camera and its performance for holography of extended objects are reported. Special corona geometry and accurate control of development heat by constant current heating and high resolution measurement of the develop temperature make easy recording of reproducible, large aperture holograms possible. The experimental results give the transfer characteristics, the diffraction efficiency characteristics and the spatial frequency response. (orig.)

Building Block Approach' for Structural Analysis of Thermoplastic Composite Components for Automotive Applications

Science.gov (United States)

Carello, M.; Amirth, N.; Airale, A. G.; Monti, M.; Romeo, A.

2017-12-01

Advanced thermoplastic prepreg composite materials stand out with regard to their ability to allow complex designs with high specific strength and stiffness. This makes them an excellent choice for lightweight automotive components to reduce mass and increase fuel efficiency, while maintaining the functionality of traditional thermosetting prepreg (and mechanical characteristics) and with a production cycle time and recyclability suited to mass production manufacturing. Currently, the aerospace and automotive sectors struggle to carry out accurate Finite Elements (FE) component analyses and in some cases are unable to validate the obtained results. In this study, structural Finite Elements Analysis (FEA) has been done on a thermoplastic fiber reinforced component designed and manufactured through an integrated injection molding process, which consists in thermoforming the prepreg laminate and overmolding the other parts. This process is usually referred to as hybrid molding, and has the provision to reinforce the zones subjected to additional stresses with thermoformed themoplastic prepreg as required and overmolded with a shortfiber thermoplastic resin in single process. This paper aims to establish an accurate predictive model on a rational basis and an innovative methodology for the structural analysis of thermoplastic composite components by comparison with the experimental tests results.

Effects of Different Wood Preservatives on The Some Physical Properties of Wood Species Used in Furniture and Building Industry

Directory of Open Access Journals (Sweden)

Abdi Atılgan

2012-04-01

Full Text Available This study aims to determine the combustion, density values of Fagus and Pinus sylvestris’ woods impregranted with Ammonium tetra fluoro borate (1 - 3 % and the mixture of cement and borax (6 % – 9 % according to ASTM-D 1413-76 standards. In the combustion test carried out according to ASTM-D 160-50, the combustion resulted from flame, the self-combustion and the combustion as glowing processes were completed and the amount of lux, combustion duration, decomposition and ash were determined. According to experimental results, it is determined that Fogus’ wood has the highest retention (42,43 kg/m3 in the mixture of cement and borax 9 %, combustion tempature (587 o C in the mixture of cement and borax 6 % , the value of lux (267 lux in the the combustion as glowing and Pinus sylvestris’ wood has the longest combustion duration (29,03 min. Ammonium tetrafluoro borate 1%, the most weight loss (94 %.

Wood handbook : wood as an engineering material

Science.gov (United States)

Robert J. Ross; Forest Products Laboratory. USDA Forest Service.

2010-01-01

Summarizes information on wood as an engineering material. Presents properties of wood and wood-based products of particular concern to the architect and engineer. Includes discussion of designing with wood and wood-based products along with some pertinent uses.

Wood anatomical and chemical properties related to the pulpability ...

African Journals Online (AJOL)

Eucalyptus globulus is one of the most important hardwood species used by the pulp and paper industry due to its high pulp yield, high wood density, excellent fibre quality and good handsheet properties. However, the wood is a highly variable and complex material that has different chemical, physical and anatomical ...

Lignonsulfonate-phenolformaldehyrde adhesive: a potential binder for wood panel industries

International Nuclear Information System (INIS)

Akhtar, T.; Lutfullah, G.; Ullah, Z.

2011-01-01

Spent sulfite liquor (SSL) was obtained from a paper mill based on grassy pulp material (bagasse, kaigrass and wheat straws). Lignosulfonate (LS) was isolated from SSL by polymerization reaction, initiated with concentrated hydrochloric acid. Different adhesives were prepared by gradual replacement of phenol by LS in phenol-formaldehyde (PF) resole resin. The strength of these resins was evaluated by glue block shear test in two wood species, in both dry and wet states. Maximum shear strength and wood failure was obtained by 20% addition of lignosulfonate to PF resin. No significant difference was observed in shear strength and wood failure of the two wood species in dry and wet states indicating that the resin obtained is waterproof. The results obtained from this study were compared with different commercial glues. Our results were found better than these glues event at a ratio 50: 50 of PF to lignosulfonate. (author)

The Effect of Ultraviolet Light on the "Liquid Wood"

Science.gov (United States)

Dumitru, Nedelcu; Sabina, Zǎgan; Ticuta, Negreanu-Pirjol; Remus, Zǎgan; Constantin, Cǎrausu

2014-08-01

To preserve resources, the goal is to use biobased materials containing the maximum possible amount of renewable biomass-based derivatives to secure a sustainable future. Bioplastics, biocomposites, biological fibres and related biomaterials will serve as substitutes for materials and products traditionally made from petroleum resources. To support this need, in 1998, Fraunhofer Institute of Chemistry and Tecnaro GmbH Company (founded by Jurgen Pfitzer and Helmut Nagele in Germany) investigated and developed a new compound made of wood components that can be processed as a thermoplastic material. It is well known that bioplastic and biocomposite materials represent another important group of bio-materials that include plastics reinforced with natural fibers and wood-plastic composites (WPCs). The aim of this research is to identify the behavior of "Liquid Wood" after UV irradiation. The materials used were Arbofill Fichte, Arboblend V2 Nature and Arboform L, V3 Nature. The samples were obtained by injection and the experimental study plan followed the Taguchi method with six input parameters and two levels for each of them. Three samples from each material were tested in an ultraviolet environment using different time of exposure in order to establish the material characteristics. After the irradiation process the material did not turn to yellow, which suggests that the composition of the sample liquid timber inhibitors have stability and the number of α-carbonyl (C = O) groups is sufficiently low. After the graphs analyzing can be inferred relatively similar performance of the samples in the first stage both UV and the VIS, indicating that the activity is almost absent. In UV is clearly observed the peak amplitude (maximum absorbance) at different wavelengths (λ). So, in terms of peak intensity the samples follow the order: Arboform L, V3 Nature; Arbofill Fichte and Arboblend V2 Nature.

Friction and bending in thermoplastic composites forming processes

NARCIS (Netherlands)

Sachs, Ulrich

2014-01-01

With the demand for better fuel economy in the aerospace and automotive industries, lightweight polymer matrix composites became an attractive alternative for metal structures. Despite the inherently higher toughness and impact damage resistance of thermoplastics, thermoset matrix composites are

Revisiting plant conservation on wooded shrines by a transversal approach: "Core" vs. "satellite" species and anthropological knowledge in Bwaba land, Burkina Faso

Directory of Open Access Journals (Sweden)

Anne Fournier

2013-03-01

Full Text Available Studies on plant conservation in sacred groves provide mixed results, with some showing their effectiveness while others do not. We argue that beyond the variety of field cases, studies usually suffer from overrating rare species and insufficient consideration of societal data. The sacred sites of Bondoukuy department in Bwaba cultural area (Burkina Faso were geo-referenced and measured; the most abundant ligneous species were listed and their abundance recorded. Their conservation status and dynamics were assessed based on the core vs. satellite species model of Hanski. Data interpretations relied on the phytogeographical affinities of abundant species and on anthropological knowledge of the Bwaba society. The vast majority of shrines were less than 1 ha, located in or near villages in specific landscape features, and covered with trees. The most abundant species of shrines belonged mostly to local phytochories, but were subject to rather high anthropisation. The results support the concept that wooded shrines preserve local biodiversity, but indicate threats from an invasive alien species. The location and condition of shrines appeared to be constitutive features: the Bwaba system of thought involves a series of sacred sites (with and without trees located in remarkable features of the landscape, and their way of life has resulted in the proximity of these sites to the villages. The beliefs that promote plant cover conservation do so only to a certain extent and regardless of the species content, which raises the concern that alien species may upset the established communities. These beliefs have led the Bwaba to choose the most humid environments in which to set up their wooded shrines, which is interesting from a conservation perspective. The study advocates for a better consideration of social data to identify the key elements of the dynamics of the vegetation of sacred groves.

Compression molding of chopped woven thermoplastic composite flakes

NARCIS (Netherlands)

Abdul Rasheed, Mohammed Iqbal

2016-01-01

Continuous fiber reinforced composites with high-performance thermoplastic polymer matrices have an enormous potential in terms of performance, production rate, cost efficiency and recyclability. The use of this relatively new class of materials by the aerospace and automotive industry has been

Performance of Teak (Tectona grandis L.F) wood on exposure to ...

African Journals Online (AJOL)

Michael Horsfall

surface splitting and checking. Its wood is therefore recommended for use as structural material in outdoor weather ... caused by UV radiation is the most damaging, however, the synergistic .... other tropical hard wood species. The effects of ...

An assessment of management practices of wood and wood-related wastes in the urban environment

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

The US Environmental Protection Agency estimates that yard waste{sup 1} accounts for approximately 16% of the municipal solid waste (MSW) stream (US EPA, 1994). Until recently, specific data and related information on this component of the (MSW) stream has been limited. The purposes of this study, phase two of the three-phase assessment of urban wood waste issues, are to assess and describe current alternatives to landfills for urban wood waste management; provide guidance on the management of urban wood waste to organizations that produce or manage wood waste; and clarify state regulatory and policy positions affecting these organizations. For this study, urban wood waste is defined as solid waste generated by tree and landscape maintenance services (public and private). Urban wood waste includes the following materials: unchipped mixed wood, unchipped logs, and unchipped tops and brush; clearing and grubbing waste; fall leaves and grass clippings; and chips and whole stumps. Construction and demolition debris and consumer-generated yard waste are not included in this study. Generators of urban wood waste include various organizations; municipal, county, and commercial tree care divisions; nurseries, orchards, and golf courses; municipal park and recreation departments; and electric and telephone utility power line maintenance, excavator and land clearance, and landscape organizations. (1) US EPA defines yard waste as ''yard trimmings'' which includes ''grass, leaves and tree brush trimmings from residential, institutional, and commercial sources.''

Wide-band tracheids are present in almost all species of Cactaceae.

Science.gov (United States)

Mauseth, James D

2004-02-01

Wide-band tracheids (WBTs) have been found in seedlings of most species of cacti that have fibrous wood in their adult bodies. Consequently, this cell type is now known to be present in almost all cacti. Earlier studies of adult plants revealed WBTs to be present only in cacti with globose or short, broad bodies, whereas all species with large columnar or long slender bodies had fibrous wood without WBTs. However, even these species produce WBTs during the first several months after germination. In species with fibrous wood in their adult bodies (species with large or slender bodies), seedlings undergo a phase transition in wood morphogenesis after a few months and stop producing the juvenile (WBT) wood and begin producing adult (fibrous) wood. If adult plants have an intermediate size, the phase transition is delayed and the plant produces WBT wood for several years. Species with globose bodies repress the phase transition completely and never switch to producing adult (fibrous) wood. Because WBTs are so widespread, they probably originated only once in Cactaceae, not multiple times as suggested earlier, or there may have been just a single origin in the Cactaceae/Portulacaceae clade.

Estimating wood volume from canopy area in deciduous woodlands ...

African Journals Online (AJOL)

In this study we tested the predictive ability of canopy area in estimating wood volume in deciduous woodlands of Zimbabwe. The study was carried out in four sites of different climatic conditions. We used regression analysis to statistically quantify the prediction of wood volume from canopy area at species and stand level ...

DIVERSITY AND ECOLOGICAL DETERMINANTS OF DEAD WOOD FUNGI IN TREE NATURAL RESERVES OF BROAD LEAVED FORESTS FROM SUCEAVA COUNTY

Directory of Open Access Journals (Sweden)

Ciprian BÎRSAN

2014-12-01

Full Text Available Dead wood fungi have a major importance for forests biodiversity as they produce wood degradation in forest habitats. In this paper are presented some aspects related to the diversity of dead wood fungi in tree deciduous forest types from tree natural reserves (Crujana, Dragomirna and Zamostea from Suceava County and the effect of some ecological factors (host tree, diameter and decomposition degree of the dead wood and some microclimatic characteristics of sites on their occurrence and diversity. Investigations carried out in 2013 resulted in the identification of 44 lignicolous fungi species. Analysis of similarities between lingnicolous fungi species from the investigated natural reserves (by hierarchical clustering shows a separation of three fungi groups, depending on the host-trees species. The effect of the tree host species was highlighted also by detrended correspondence analysis, which, in addition presented the existence of an altitudinal gradient and a weaker effect of site conditions (slope and aspect and microclimatic variables (solar radiation on dead wood fungi occurrence. The effect of diameter and decomposition degree of fallen trunks and branches on dead wood fungi species was investigated using the redundancy analysis showing that wood debris with large surfaces are more easily colonized by the fungi species developing large sporocarps compared to small branches with low diameters colonized only by few or a single fungus species.

Mechanical behaviour of textile-reinforced thermoplastics with integrated sensor network components

International Nuclear Information System (INIS)

Hufenbach, W.; Adam, F.; Fischer, W.-J.; Kunadt, A.; Weck, D.

2011-01-01

Highlights: → Consideration of two types of integrated bus systems for textile-reinforced thermoplastics with embedded sensor networks. → Specimens with bus systems made of flexible printed circuit boards show good mechanical performance compared to the reference. → Inhomogeneous interface and reduced stiffnesses and strengths for specimens with bus systems basing on single copper wires. -- Abstract: The embedding of sensor networks into textile-reinforced thermoplastics enables the design of function-integrative lightweight components suitable for high volume production. In order to investigate the mechanical behaviour of such functionalised composites, two types of bus systems are selected as exemplary components of sensor networks. These elements are embedded into glass fibre-reinforced polypropylene (GF/PP) during the layup process of unconsolidated weft-knitted GF/PP-preforms. Two fibre orientations are considered and orthotropic composite plates are manufactured by hot pressing technology. Micrograph investigations and computer tomography analyses show different interface qualities between the thermoplastic composite and the two types of bus systems. Mechanical tests under tensile and flexural loading indicate a significant influence of the embedded bus system elements on the structural stiffness and strength.

Nanocomposites Based on Thermoplastic Polymers and Functional Nanofiller for Sensor Applications

Directory of Open Access Journals (Sweden)

Serena Coiai

2015-06-01

Full Text Available Thermoplastic polymers like polyolefins, polyesters, polyamide, and styrene polymers are the most representative commodity plastics thanks to their cost-efficient manufacturing processes, excellent thermomechanical properties and their good environmental compatibility, including easy recycling. In the last few decades much effort has been devoted worldwide to extend the applications of such materials by conferring on them new properties through mixing and blending with different additives. In this latter context, nanocomposites have recently offered new exciting possibilities. This review discusses the successful use of nanostructured dispersed substrates in designing new stimuli-responsive nanocomposites; in particular, it provides an updated description of the synthetic routes to prepare nanostructured systems having the typical properties of thermoplastic polymers (continuous matrix, but showing enhanced optical, conductive, and thermal features dependent on the dispersion topology. The controlled nanodispersion of functional labeled clays, noble metal nanoparticles and carbon nanotubes is here evidenced to play a key role in producing hybrid thermoplastic materials that have been used in the design of devices, such as NLO devices, chemiresistors, temperature and deformation sensors.

Nanocomposites Based on Thermoplastic Polymers and Functional Nanofiller for Sensor Applications

Science.gov (United States)

Coiai, Serena; Passaglia, Elisa; Pucci, Andrea; Ruggeri, Giacomo

2015-01-01

Thermoplastic polymers like polyolefins, polyesters, polyamide, and styrene polymers are the most representative commodity plastics thanks to their cost-efficient manufacturing processes, excellent thermomechanical properties and their good environmental compatibility, including easy recycling. In the last few decades much effort has been devoted worldwide to extend the applications of such materials by conferring on them new properties through mixing and blending with different additives. In this latter context, nanocomposites have recently offered new exciting possibilities. This review discusses the successful use of nanostructured dispersed substrates in designing new stimuli-responsive nanocomposites; in particular, it provides an updated description of the synthetic routes to prepare nanostructured systems having the typical properties of thermoplastic polymers (continuous matrix), but showing enhanced optical, conductive, and thermal features dependent on the dispersion topology. The controlled nanodispersion of functional labeled clays, noble metal nanoparticles and carbon nanotubes is here evidenced to play a key role in producing hybrid thermoplastic materials that have been used in the design of devices, such as NLO devices, chemiresistors, temperature and deformation sensors.

EVALUATION OF STRENGTH TO SHEAR AND DELAMINATION IN GLUED LAMINATED WOOD

Directory of Open Access Journals (Sweden)

Carlito Calil Neto

2014-12-01

Full Text Available The Glued Laminated Wood has a large range of applications. In Brazil, its employment as cross-piece poles for overhead electrical power has attracted the attention of companies in the industry, motivated by the potential use of this material. Among the factors that influence the mechanical performance of Glulam solutions stand out efficiency and affinity of the adhesives to the species of wood used, the type of treatment and moisture content of wood veneer, motivating the development of new research on this topic. This research aimed to investigate, by Design of Experiments (DOE, the influence of wood (pinus, teca, eucalipto, adhesive (Purbond; Cascophen and treatment (CCA, CCB, CCBS in the variable responses shear strength and delamination, consisting in the same combination factors evaluated in ANEEL/EESC-PD220-07 project: Head Crosshead Glulam Series. The results of the statistical analysis showed that the species factor expressed significant effect for both response variables evaluated, did not occur with adhesive and treatment factors. Moisture content was significant in the wood evaluated when analyzed the shear strength, and the teca wood showed the highest shear strength and also relating to the delamination.

Slope failure as an upslope source of stream wood

Science.gov (United States)

Daniel. Miller

2013-01-01

Large woody debris is recognized as an important component of stream geomorphology and stream ecosystem function, and forest-land management is recognized as an important control on the quantity (and size and species distributions) of wood available for recruitment to streams. Much of the wood present in streams comes from adjacent forests, and riparian management...

Transpiration efficiency over an annual cycle, leaf gas exchange and wood carbon isotope ratio of three tropical tree species.

Science.gov (United States)

Cernusak, Lucas A; Winter, Klaus; Aranda, Jorge; Virgo, Aurelio; Garcia, Milton

2009-09-01

Variation in transpiration efficiency (TE) and its relationship with the stable carbon isotope ratio of wood was investigated in the saplings of three tropical tree species. Five individuals each of Platymiscium pinnatum (Jacq.) Dugand, Swietenia macrophylla King and Tectona grandis Linn. f. were grown individually in large (760 l) pots over 16 months in the Republic of Panama. Cumulative transpiration was determined by repeatedly weighing the pots with a pallet truck scale. Dry matter production was determined by destructive harvest. The TE, expressed as experiment-long dry matter production divided by cumulative water use, averaged 4.1, 4.3 and 2.9 g dry matter kg(-1) water for P. pinnatum, S. macrophylla and T. grandis, respectively. The TE of T. grandis was significantly lower than that of the other two species. Instantaneous measurements of the ratio of intercellular to ambient CO(2) partial pressures (c(i)/c(a)), taken near the end of the experiment, explained 66% of variation in TE. Stomatal conductance was lower in S. macrophylla than in T. grandis, whereas P. pinnatum had similar stomatal conductance to T. grandis, but with a higher photosynthetic rate. Thus, c(i)/c(a) and TE appeared to vary in response to both stomatal conductance and photosynthetic capacity. Stem-wood delta(13)C varied over a relatively narrow range of just 2.2 per thousand, but still explained 28% of variation in TE. The results suggest that leaf-level processes largely determined variation among the three tropical tree species in whole-plant water-use efficiency integrated over a full annual cycle.

Diamond turning of thermoplastic polymers

Energy Technology Data Exchange (ETDEWEB)

Smith, E.; Scattergood, R.O.

1988-12-01

Single point diamond turning studies were made using a series of thermoplastic polymers with different glass transition temperatures. Variations in surface morphology and surface roughness were observed as a function of cutting speed. Lower glass transition temperatures facilitate smoother surface cuts and better surface finish. This can be attributed to the frictional heating that occurs during machining. Because of the very low glass transition temperatures in polymeric compared to inorganic glasses, the precision machining response can be very speed sensitive.

Enhanced printability of thermoplastic polyurethane substrates by silica particles surface interactions

Energy Technology Data Exchange (ETDEWEB)

Cruz, S., E-mail: s.cruz@dep.uminho.pt [IPC/I3N – Institute of Polymers and Composites/Inst. of Nanostructures, Nanomodelling and Nanofabrication, Department Polymer Engineering, University of Minho, 4804-533 Guimarães (Portugal); Rocha, L.A. [CMEMS, University of Minho, 4804-533 Guimarães (Portugal); Viana, J.C. [IPC/I3N – Institute of Polymers and Composites/Inst. of Nanostructures, Nanomodelling and Nanofabrication, Department Polymer Engineering, University of Minho, 4804-533 Guimarães (Portugal)

2016-01-01

Graphical abstract: - Highlights: • A new method development for surface treatment of thermoplastic polyurethane (TPU) substrates. • The proposed method increases TPU surface energy (by 45%) and consequently the TPU wettability. • Great increase of the TPU surface roughness (by 621%). • Inkjet printed conductive ink was applied to the surface treated TPU substrate and significant improvements on the printability were obtained. - Abstract: A new method developed for the surface treatment of thermoplastic polymer substrates that increases their surface energies is introduced in this paper. The method is environmental friendly and low cost. In the proposed surface treatment method, nanoparticles are spread over the thermoplastic polyurethane (TPU) flexible substrate surface and then thermally fixed. This latter step allows the nanoparticles sinking-in on the polymer surface, resulting in a higher polymer–particle interaction at their interfacial region. The addition of nanoparticles onto the polymer surface increases surface roughness. The extent of the nanoparticles dispersion and sink-in in the substrate was evaluated through microscopy analysis (SEM). The roughness of the surface treated polymeric substrate was evaluated by AFM analysis. Substrate critical surface tension (ST) was measured by contact angle. In general, a homogeneous roughness form is achieved to a certain level. Great increase of the TPU surface roughness (by 621%) was induced by the propose method. The proposed surface treatment method increased significantly the substrate ST (by 45%) and consequently the TPU wettability. This novel surface treatment of thermoplastic polymers was applied to the inkjet printing of TPU substrates with conductive inks, and significant improvements on the printability were obtained.

Review of potential processing techniques for the encapsulation of wastes in thermoplastic polymers

International Nuclear Information System (INIS)

Patel, B.R.; Lageraaen, P.R.; Kalb, P.D.

1995-08-01

Thermoplastic encapsulation has been extensively studied at Brookhaven National Laboratory's (BNL) Environmental and Waste Technology Center (EWTC) as a waste encapsulation technology applicable to a wide range of waste types including radioactive, hazardous and mixed wastes. Encapsulation involves processing thermoplastic and waste materials into a waste form product by heating and mixing both materials into a homogeneous molten mixture. Cooling of the melt results in a solid monolithic waste form in which contaminants have been completely surrounded by a polymer matrix. Heating and mixing requirements for successful waste encapsulation can be met using proven technologies available in various types of commercial equipment. Processing techniques for thermoplastic materials, such as low density polyethylene (LDPE), are well established within the plastics industry. The majority of commercial polymer processing is accomplished using extruders, mixers or a combination of these technologies. Extruders and mixers are available in a broad range of designs and are used during the manufacture of consumer and commercial products as well as for compounding applications. Compounding which refers to mixing additives such as stabilizers and/or colorants with polymers, is analogous to thermoplastic encapsulation. Several processing technologies were investigated for their potential application in encapsulating residual sorbent waste in selected thermoplastic polymers, including single-screw extruders, twin-screw extruders, continuous mixers, batch mixers as well as other less conventional devices. Each was evaluated based on operational ease, quality control, waste handling capabilities as well as degree of waste pretreatment required. Based on literature review, this report provides a description of polymer processing technologies, a discussion of the merits and limitations of each and an evaluation of their applicability to the encapsulation of sorbent wastes

Review of potential processing techniques for the encapsulation of wastes in thermoplastic polymers

Energy Technology Data Exchange (ETDEWEB)

Patel, B.R.; Lageraaen, P.R.; Kalb, P.D.

1995-08-01

Thermoplastic encapsulation has been extensively studied at Brookhaven National Laboratory`s (BNL) Environmental and Waste Technology Center (EWTC) as a waste encapsulation technology applicable to a wide range of waste types including radioactive, hazardous and mixed wastes. Encapsulation involves processing thermoplastic and waste materials into a waste form product by heating and mixing both materials into a homogeneous molten mixture. Cooling of the melt results in a solid monolithic waste form in which contaminants have been completely surrounded by a polymer matrix. Heating and mixing requirements for successful waste encapsulation can be met using proven technologies available in various types of commercial equipment. Processing techniques for thermoplastic materials, such as low density polyethylene (LDPE), are well established within the plastics industry. The majority of commercial polymer processing is accomplished using extruders, mixers or a combination of these technologies. Extruders and mixers are available in a broad range of designs and are used during the manufacture of consumer and commercial products as well as for compounding applications. Compounding which refers to mixing additives such as stabilizers and/or colorants with polymers, is analogous to thermoplastic encapsulation. Several processing technologies were investigated for their potential application in encapsulating residual sorbent waste in selected thermoplastic polymers, including single-screw extruders, twin-screw extruders, continuous mixers, batch mixers as well as other less conventional devices. Each was evaluated based on operational ease, quality control, waste handling capabilities as well as degree of waste pretreatment required. Based on literature review, this report provides a description of polymer processing technologies, a discussion of the merits and limitations of each and an evaluation of their applicability to the encapsulation of sorbent wastes.

Comparative wood anatomy of the blueberry tribe (Vaccinieae, Ericaceae s.l.)

NARCIS (Netherlands)

Lens, F.; Kron, K.A.; Luteyn, J.L.; Smets, E.; Jansen, S.

2004-01-01

Wood samples of 111 Vaccinieae specimens (Vaccinioideae, Ericaceae s.l.) representing 98 species and 26 genera are investigated with light microscopy and scanning electron microscopy. The wood structure of Vaccinieae delivers taxonomically important characters that can be used to define some

Materials and process limitations for thermoplastic composite materials for wind turbine blades - preform of prepregs and commingled yarns

Energy Technology Data Exchange (ETDEWEB)

Prabhakaran, R.T.D.

2011-07-01

Wind turbine blades are produced based on the current thermoset resin technology, but thermoplastics can offer better potential to become the future blade materials. One of the most important goals when designing larger blade systems is to keep the blade weight under control. Thermoplastic materials offer weight saving similar to thermosets, apart from many other benefits like design flexibility, durability, cost, weight saving, and performance advantageous to the wind industry. In the current research study a detailed discussion on material and process limitations such as thermoplastic prepreg tapes and commingled yams are presented in terms of their properties and available forms in the current markets. A critical review of thermoplastics discussed in the context of turbine blades applications. (Author)

Business environment in the wood fuels field

International Nuclear Information System (INIS)

Laitinen, H.; Ranta, T.

1995-01-01

In this publication the business environment in the wood fuels sector and the internal and external factors affecting it are studied. It has been considered important to describe both the present situation and future possibilities of the business in order to develop it so that the planned increase in the use of wood fuels can be achieved

The effect of titanium surface treatment on the interfacial strength of titanium – Thermoplastic composite joints

NARCIS (Netherlands)

Su, Yibo; de Rooij, Matthijn; Grouve, Wouter; Akkerman, Remko

2017-01-01

Co-consolidated titanium – carbon fibre reinforced thermoplastic composite hybrid joints show potential for application in aerospace structures. The strength of the interface between the titanium and the thermoplastic composite is crucial for the strength of the entire hybrid joint. Application of a

Wood-plastic composites as promising green-composites for automotive industries!

Science.gov (United States)

Ashori, Alireza

2008-07-01

Wood-plastic composite (WPC) is a very promising and sustainable green material to achieve durability without using toxic chemicals. The term WPCs refers to any composites that contain plant fiber and thermosets or thermoplastics. In comparison to other fibrous materials, plant fibers are in general suitable to reinforce plastics due to relative high strength and stiffness, low cost, low density, low CO2 emission, biodegradability and annually renewable. Plant fibers as fillers and reinforcements for polymers are currently the fastest-growing type of polymer additives. Since automakers are aiming to make every part either recyclable or biodegradable, there still seems to be some scope for green-composites based on biodegradable polymers and plant fibers. From a technical point of view, these bio-based composites will enhance mechanical strength and acoustic performance, reduce material weight and fuel consumption, lower production cost, improve passenger safety and shatterproof performance under extreme temperature changes, and improve biodegradability for the auto interior parts.

Unusual distribution of Zfy and Zfx sequences on the sex chromosomes of the wood lemming, a species exhibiting XY sex reversal.

Science.gov (United States)

Lau, Y F; Yang-Feng, T L; Elder, B; Fredga, K; Wiberg, U H

1992-01-01

Sex reversal occurs naturally in the wood lemming (Myopus schisticolor) due to the presence in populations of this species of a variant (mutated) X chromosome, designated X*. Thus, X*Y animals develop into females, whereas XY animals develop into normal males. Chromosome mapping by in situ hybridization of DNA sequences homologous to the human ZFY gene localized the wood lemming Zfx sequences to region p12----p11 on both the wild-type X and the mutated X* chromosomes, at or proximal to a presumed breakpoint (Xp12) involved in the generation of the X* chromosome from the normal X, and Zfy sequences along the entire short arm of the Y chromosome. Differences between Zfx and Zfx* were readily detected by Southern blot analysis. However, both the Zfx and Zfx* genes expressed similarly sized transcripts in all adult somatic tissues investigated. Although the precise molecular difference between the Zfx and Zfx* genes is still unknown, their chromosomal location suggests that either Zfx or some other closely linked gene(s) on the X chromosome may be a major X-linked sex-determining gene, Tdx, which in the X* chromosome fails to interact properly with the Y-linked testis-determining gene, Tdy, thus causing X*Y embryos to develop into females. At least 15 copies of wood lemming Zfy sequences are distributed along the short arm of the Y chromosome. Northern hybridization analyses of adult tissues and somatic cell lines indicated that these Zfy repeats were transcriptionally inactive. Normally, 3-kb Zfy (ZFY) transcripts are readily detected in mouse and human testes, especially in the germ cells. It has therefore been postulated that expression of the Zfy (ZFY) gene may be important for spermatogenesis. Whether the lack of sufficient Zfy transcripts in the testis of the adult wood lemming has any impact on spermatogenesis in this species is still to be elucidated by further studies.

Global timber investments, wood costs, regulation, and risk

Science.gov (United States)

F. Cubbage; S. Koesbandana; P Mac Donagh; R. Rubilar; G Balmelli; V. Morales Olmos; R. De La Torre; M. Murara; V.A. Hoeflich; H. Kotze; R Gonzalez; O. Carrero; G. Frey; T. Adams; J. Turner; R. Lord; J. Huang; C. MacIntyre; Kathleen McGinley; R. Abt; R. Phillips

2010-01-01

We estimated financial returns and wood production costs in 2008 for the primary timber plantation species. Excluding land costs, returns for exotic plantations in almost all of South America e Brazil, Argentina, Uruguay, Chile, Colombia, Venezuela, and Paraguay e were substantial. Eucalyptus species returns were generally greater than those for Pinus species in each...

Species composition and forest structure explain the temperature sensitivity patterns of productivity in temperate forests

Directory of Open Access Journals (Sweden)

F. J. Bohn

2018-03-01

Full Text Available Rising temperatures due to climate change influence the wood production of forests. Observations show that some temperate forests increase their productivity, whereas others reduce their productivity. This study focuses on how species composition and forest structure properties influence the temperature sensitivity of aboveground wood production (AWP. It further investigates which forests will increase their productivity the most with rising temperatures. We described forest structure by leaf area index, forest height and tree height heterogeneity. Species composition was described by a functional diversity index (Rao's Q and a species distribution index (ΩAWP. ΩAWP quantified how well species are distributed over the different forest layers with regard to AWP. We analysed 370 170 forest stands generated with a forest gap model. These forest stands covered a wide range of possible forest types. For each stand, we estimated annual aboveground wood production and performed a climate sensitivity analysis based on 320 different climate time series (of 1-year length. The scenarios differed in mean annual temperature and annual temperature amplitude. Temperature sensitivity of wood production was quantified as the relative change in productivity resulting from a 1 °C rise in mean annual temperature or annual temperature amplitude. Increasing ΩAWP positively influenced both temperature sensitivity indices of forest, whereas forest height showed a bell-shaped relationship with both indices. Further, we found forests in each successional stage that are positively affected by temperature rise. For such forests, large ΩAWP values were important. In the case of young forests, low functional diversity and small tree height heterogeneity were associated with a positive effect of temperature on wood production. During later successional stages, higher species diversity and larger tree height heterogeneity were an advantage. To achieve such a

Species composition and forest structure explain the temperature sensitivity patterns of productivity in temperate forests

Science.gov (United States)

Bohn, Friedrich J.; May, Felix; Huth, Andreas

2018-03-01

Rising temperatures due to climate change influence the wood production of forests. Observations show that some temperate forests increase their productivity, whereas others reduce their productivity. This study focuses on how species composition and forest structure properties influence the temperature sensitivity of aboveground wood production (AWP). It further investigates which forests will increase their productivity the most with rising temperatures. We described forest structure by leaf area index, forest height and tree height heterogeneity. Species composition was described by a functional diversity index (Rao's Q) and a species distribution index (ΩAWP). ΩAWP quantified how well species are distributed over the different forest layers with regard to AWP. We analysed 370 170 forest stands generated with a forest gap model. These forest stands covered a wide range of possible forest types. For each stand, we estimated annual aboveground wood production and performed a climate sensitivity analysis based on 320 different climate time series (of 1-year length). The scenarios differed in mean annual temperature and annual temperature amplitude. Temperature sensitivity of wood production was quantified as the relative change in productivity resulting from a 1 °C rise in mean annual temperature or annual temperature amplitude. Increasing ΩAWP positively influenced both temperature sensitivity indices of forest, whereas forest height showed a bell-shaped relationship with both indices. Further, we found forests in each successional stage that are positively affected by temperature rise. For such forests, large ΩAWP values were important. In the case of young forests, low functional diversity and small tree height heterogeneity were associated with a positive effect of temperature on wood production. During later successional stages, higher species diversity and larger tree height heterogeneity were an advantage. To achieve such a development, one could plant

Method and apparatus for extruding thermoplastic material

International Nuclear Information System (INIS)

McKelvey, J.M.

1985-01-01

A gear pump assisted screw conveyor extrusion system utilizing a cartridge heating device disposed axially within the screw and having the drives for the gear pump and the screw correlated in speed to create relatively little pressure in the thermoplastic material being extruded such that relatively little mechanical working thereof occurs. The thermoplastic material is melted in the screw conveyor primarily by heat transfer from the cartridge heater and the gear pump is utilized for conveying the melted material under pressure to a subsequent work station. A relatively deep material-conveying spiral channel is provided in the screw for maximized extrusion output per revolution of the screw and minimized mechanical energy generation by the screw. A motionless mixer may be employed intermediate the screw and the work station to homogenize the melted material for reducing temperature gradients therein. The system advantageously is capable of extruding material at a substantially greater rate and a lower material temperature and with substantially increased power economy than conventional systems utilizing a high pressure, externally heated screw conveyor portion

Development and evaluation of thermoplastic street maintenance material

Science.gov (United States)

Siemens, W. D.

1973-01-01

An all-weather permanent street patching material was investigated for flexible and rigid pavements. The economic, operational, and material requirements are discussed along with the results of field tests with various mixtures of EVA resins and asphalt. Cost analyses for thermoplastic patching methods are included.

Resistance Welding of Thermoplastic Composites : Process and Performance

NARCIS (Netherlands)

Shi, H.

2014-01-01

Compared to thermoset composites, thermoplastic composites are drawing more and more attention by aircraft industries not only due to their excellent material properties but also due to their potentials to reduce cycle time and structure cost by using low-cost manufacturing technologies such as

Clinical application of removable partial dentures using thermoplastic resin. Part II: Material properties and clinical features of non-metal clasp dentures.

Science.gov (United States)

Fueki, Kenji; Ohkubo, Chikahiro; Yatabe, Masaru; Arakawa, Ichiro; Arita, Masahiro; Ino, Satoshi; Kanamori, Toshikazu; Kawai, Yasuhiko; Kawara, Misao; Komiyama, Osamu; Suzuki, Tetsuya; Nagata, Kazuhiro; Hosoki, Maki; Masumi, Shin-ichi; Yamauchi, Mutsuo; Aita, Hideki; Ono, Takahiro; Kondo, Hisatomo; Tamaki, Katsushi; Matsuka, Yoshizo; Tsukasaki, Hiroaki; Fujisawa, Masanori; Baba, Kazuyoshi; Koyano, Kiyoshi; Yatani, Hirofumi

2014-04-01

This position paper reviews physical and mechanical properties of thermoplastic resin used for non-metal clasp dentures, and describes feature of each thermoplastic resin in clinical application of non-metal clasp dentures and complications based on clinical experience of expert panels. Since products of thermoplastic resin have great variability in physical and mechanical properties, clinicians should utilize them with careful consideration of the specific properties of each product. In general, thermoplastic resin has lower color-stability and higher risk for fracture than polymethyl methacrylate. Additionally, the surface of thermoplastic resin becomes roughened more easily than polymethyl methacrylate. Studies related to material properties of thermoplastic resin, treatment efficacy and follow-up are insufficient to provide definitive conclusions at this time. Therefore, this position paper should be revised based on future studies and a clinical guideline should be provided. Copyright © 2014 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Numerical modeling and experimental validation of thermoplastic composites induction welding

Science.gov (United States)

Palmieri, Barbara; Nele, Luigi; Galise, Francesco

2018-05-01

In this work, a numerical simulation and experimental test of the induction welding of continuous fibre-reinforced thermoplastic composites (CFRTPCs) was provided. The thermoplastic Polyamide 66 (PA66) with carbon fiber fabric was used. Using a dedicated software (JMag Designer), the influence of the fundamental process parameters such as temperature, current and holding time was investigated. In order to validate the results of the simulations, and therefore the numerical model used, experimental tests were carried out, and the temperature values measured during the tests were compared with the aid of an optical pyrometer, with those provided by the numerical simulation. The mechanical properties of the welded joints were evaluated by single lap shear tests.

Methods of Recycling, Properties and Applications of Recycled Thermoplastic Polymers

Directory of Open Access Journals (Sweden)

Mădălina Elena Grigore

2017-11-01

Full Text Available This study aims to provide an updated survey of the main thermoplastic polymers in order to obtain recyclable materials for various industrial and indoor applications. The synthesis approach significantly impacts the properties of such materials and these properties in turn have a significant impact on their applications. Due to the ideal properties of the thermoplastic polymers such as corrosion resistance, low density or user-friendly design, the production of plastics has increased markedly over the last 60 years, becoming more used than aluminum or other metals. Also, recycling is one of the most important actions currently available to reduce these impacts and represents one of the most dynamic areas in the plastics industry today.

Changes in wood density, wood anatomy and hydraulic properties of the xylem along the root-to-shoot flow path in tropical rainforest trees.

Science.gov (United States)

Schuldt, Bernhard; Leuschner, Christoph; Brock, Nicolai; Horna, Viviana

2013-02-01

It is generally assumed that the largest vessels are occurring in the roots and that vessel diameters and the related hydraulic conductance in the xylem are decreasing acropetally from roots to leaves. With this study in five tree species of a perhumid tropical rainforest in Sulawesi (Indonesia), we searched for patterns in hydraulic architecture and axial conductivity along the flow path from small-diameter roots through strong roots and the trunk to distal sun-canopy twigs. Wood density differed by not more than 10% across the different flow path positions in a species, and branch and stem wood density were closely related in three of the five species. Other than wood density, the wood anatomical and xylem hydraulic traits varied in dependence on the position along the flow path, but were unrelated to wood density within a tree. In contrast to reports from conifers and certain dicotyledonous species, we found a hump-shaped variation in vessel diameter and sapwood area--specific conductivity along the flow path in all five species with a maximum in the trunk and strong roots and minima in both small roots and twigs; the vessel size depended on the diameter of the organ. This pattern might be an adaptation to the perhumid climate with a low risk of hydraulic failure. Despite a similar mean vessel diameter in small roots and twigs, the two distal organs, hydraulically weighted mean vessel diameters were on average 30% larger in small roots, resulting in ∼ 85% higher empirical and theoretical specific conductivities. Relative vessel lumen area in percent of sapwood area decreased linearly by 70% from roots to twigs, reflecting the increase in sclerenchymatic tissue and tracheids in acropetal direction in the xylem. Vessel size was more closely related to the organ diameter than to the distance along the root-to-shoot flow path. We conclude that (i) the five co-occurring tree species show convergent patterns in their hydraulic architecture despite different growth

Near-infrared spectroscopic observation of the ageing process in archaeological wood using a deuterium exchange method.

Science.gov (United States)

Tsuchikawa, Satoru; Yonenobu, Hitoshi; Siesler, H W

2005-03-01

The ageing degradation of the fine wood structure of dry-exposed archaeological wood was investigated by Fourier transform near-infrared spectroscopy with the aid of a deuterium exchange method. The archaeological wood sample was taken from an old wooden temple in Japan (late 7th century), which has been designated as a UNESCO world heritage site. Comparing the analytical results with those of a modern wood sample of the same species, the ageing process of archaeological wood was clarified as a change in the state of order on a macromolecular structural level. It can be concluded from NIR spectra that the amorphous region, and partially semi-crystalline region, in cellulose, hemicellulose, and lignin decreased by the ageing degradation, whereas the crystalline region in cellulose was not affected by the ageing. The accessibility of the diffusant to effect H/D-exchange was monitored by an OH-related absorption band obtained from FT-NIR transmission spectroscopy and characteristically varied with the ageing process of the wood samples, the absorption bands characteristic of a specific state of order and the diffusion agent. Finally, we proposed a morphological model to describe the variation of the fine structure of the microfibrils in the cell wall with ageing degradation. The state of microfibrils changed loosely by ageing, so that elementary fibrils were arranged loosely under 5 A, whereas several elementary fibrils in the modern wood were arranged in very close proximity under 3 A to each other.

Mummified fossil woods of Fagaceae from the upper Oligocene of Guangxi, South China

Science.gov (United States)

Huang, Luliang; Jin, Jianhua; Quan, Cheng; Oskolski, Alexei A.

2018-02-01

Three new fossil species, two attributed to the genus Castanopsis (C. nanningensis and C. guangxiensis) and one to the organ genus Lithocarpoxylon (L. nanningensis) are described on the basis of well-preserved mummified wood from the upper Oligocene of Yongning Formation in the Nanning Basin, Guangxi Province, South China. The two species of Castanopsis represent the most ancient reliable wood record of this genus in China and also southeastern Asia, which is the center of diversity of extant species. The fossil leaf records of Castanopsis indicated this genus has migrated to South China in the late Eocene. This fossil wood evidence confirms the presence and persistence of Castanopsis in this region in the late Oligocene. In the Yongning Formation, the presence of numerous Fagaceae woods with faint or absent growth ring boundaries (in C. nanningensis) occasionally associated with prominent ring-porous patterns, suggests that Guangxi (South China) had a seasonal (probably monsoonal) tropical climate during the late Oligocene.

Effects of application methods and species of wood on color ...

African Journals Online (AJOL)

PRECIOUS

2009-11-02

Nov 2, 2009 ... methods. Key words: Waterborne varnishes, application methods, wood materials, color change. ... rate in open air conditions (Anderson et al., 1991). .... for topcoat application and they were held for drying for 3 weeks. Finally ...

Mechanical properties of carbon fibre reinforced thermoplastics for cryogenic applications

International Nuclear Information System (INIS)

Ahlborn, K.

1989-01-01

The high specific strength, the high specific stiffness and the excellent fatigue behaviour favours carbon fibre reinforced plastics (CFRP) as a supplement to metals for low temperature applications. The weakest link in the composite is the polymeric matrix, which is preloaded by thermal tensile strains and becomes brittle at low temperatures. Tough thermoplastic polymers show a higher cryogenic fracture strain than commonly used epoxy-matrix systems. Two carbon fibre reinforced tough thermoplastics (PEEK, PC) were tested at 293 K, 77 K and 5 K by tensile, bending and fatigue loading. It has been found, that the toughness of the matrices generally improves the static strength at low temperatures. In bidirectionally reinforced thermoplastics, transversal cracks appear in the matrix or in the boundary layer at composite strains below 0,2%, originated by the thermal preloading. The formation and development of the cracks depend on the fibre-matrix-bond and on the thickness of the composite layers. Fibre-misalignment results in a poor tension-tension fatigue endurance limit of less than 50% of the static strength. Further developments in the manufacturing process are necessary to improve the homogeneity of the composite structure in order to increase the long term fatigue behaviour. (orig.) [de

Dominant Tree Species and Soil Type Affect the Fungal Community Structure in a Boreal Peatland Forest.

Science.gov (United States)

Sun, Hui; Terhonen, Eeva; Kovalchuk, Andriy; Tuovila, Hanna; Chen, Hongxin; Oghenekaro, Abbot O; Heinonsalo, Jussi; Kohler, Annegret; Kasanen, Risto; Vasander, Harri; Asiegbu, Fred O

2016-05-01

Boreal peatlands play a crucial role in global carbon cycling, acting as an important carbon reservoir. However, little information is available on how peatland microbial communities are influenced by natural variability or human-induced disturbances. In this study, we have investigated the fungal diversity and community structure of both the organic soil layer and buried wood in boreal forest soils using high-throughput sequencing of the internal transcribed spacer (ITS) region. We have also compared the fungal communities during the primary colonization of wood with those of the surrounding soils. A permutational multivariate analysis of variance (PERMANOVA) confirmed that the community composition significantly differed between soil types (P< 0.001) and tree species (P< 0.001). The distance-based linear models analysis showed that environmental variables were significantly correlated with community structure (P< 0.04). The availability of soil nutrients (Ca [P= 0.002], Fe [P= 0.003], and P [P= 0.003]) within the site was an important factor in the fungal community composition. The species richness in wood was significantly lower than in the corresponding soil (P< 0.004). The results of the molecular identification were supplemented by fruiting body surveys. Seven of the genera of Agaricomycotina identified in our surveys were among the top 20 genera observed in pyrosequencing data. Our study is the first, to our knowledge, fungal high-throughput next-generation sequencing study performed on peatlands; it further provides a baseline for the investigation of the dynamics of the fungal community in the boreal peatlands. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

Comparative wood anatomy of some shrubs native to the Northern Rocky Mountains

Science.gov (United States)

Arlene Dale

1968-01-01

This paper describes some xylem characteristics of the more important shrub species of the Northern Rockies and presents a key for identifying shrub-wood specimens by microscopic characters. The paper contains photomicrographs of 55 shrub woods.

Energy from wood biomass: The experience of the Brazilian forest sector

Energy Technology Data Exchange (ETDEWEB)

Couto, L. [Universidade Federal de Vicosa (Brazil); Graca, L.R. [Centro Nacional de Pesquisa de Floresta, Colombo (Brazil); Betters, D.R. [Colorado State Univ., Fort Collins, CO (United States)

1993-12-31

Wood biomass is one of the most significant renewable sources of energy in Brazil. Fuelwood and charcoal play a very important role not only for household energy consumption but also for the cement, iron and steel industries. Wood is used as an energy source by the pulp and paper, composite board and other industries of the country, mainly for steam and electricity generation. Ethanol, lignin-based coke and methanol from wood were produced at experimental units in Brazil but were not implemented on a commercial scale. Currently, a new experimental plant using a technology developed in the US is being built in the state of Bahia to generate electricity from Eucalyptus. This technology is a Biomass Integrated Gasification/Gas Turbine process which is expected to make the use of wood biomass economically feasible for electricity generation. Forest plantations are the main source of wood biomass for energy consumption by the Brazilian industrial sector. Fiscal incentives in the 1960s helped the country to begin a massive reforestation program mainly using Eucalyptus and Pinus species. A native species, bracatinga (Mimosa scabrella) has also been used extensively for wood energy plantations in southern Brazil. Technical, economic, social and environmental impacts of these plantation forests are discussed along with a forecast of the future wood energy utilization in Brazil.

Determination of adhesion between thermoplastic and liquid silicone rubbers in hard-soft-combinations via mechanical peeling test

Science.gov (United States)

Kühr, C.; Spörrer, A.; Altstädt, V.

2014-05-01

The production of hard-soft-combinations via multi injection molding gained more and more importance in the last years. This is attributed to different factors. One principle reason is that the use of two-component injection molding technique has many advantages such as cancelling subsequent and complex steps and shortening the process chain. Furthermore this technique allows the combination of the properties of the single components like the high stiffness of the hard component and the elastic properties of the soft component. Because of the incompatibility of some polymers the adhesion on the interface has to be determined. Thereby adhesion is not only influenced by the applied polymers, but also by the injection molding parameters and the characteristics of the mold. Besides already known combinations of thermoplastics with thermoplastic elastomers (TPE), there consists the possibility to apply liquid silicone rubber (LSR) as soft component. A thermoplastic/LSR combination gains in importance due to the specific advantages of LSR to TPE. The faintly adhesion between LSR and thermoplastics is currently one of the key challenges when dealing with those combinations. So it is coercively necessary to improve adhesion between the two components by adding an adhesion promoter. To determine the promoters influence, it is necessary to develop a suitable testing method to investigate e.g. the peel resistance. The current German standard "VDI Richtlinie 2019', which is actually only employed for thermoplastic/TPE combinations, can serve as a model to determine the adhesion of thermoplastic/LSR combinations.

Effects of Styrene-Acrylic Sizing on the Mechanical Properties of Carbon Fiber Thermoplastic Towpregs and Their Composites.

Science.gov (United States)

Bowman, Sean; Jiang, Qiuran; Memon, Hafeezullah; Qiu, Yiping; Liu, Wanshuang; Wei, Yi

2018-03-01

Thermoplastic towpregs are convenient and scalable raw materials for the fabrication of continuous fiber-reinforced thermoplastic matrix composites. In this paper, the potential to employ epoxy and styrene-acrylic sizing agents was evaluated for the making of carbon fiber thermoplastic towpregs via a powder-coating method. The protective effects and thermal stability of these sizing agents were investigated by single fiber tensile test and differential scanning calorimetry (DSC) measurement. The results indicate that the epoxy sizing agent provides better protection to carbon fibers, but it cannot be used for thermoplastic towpreg processing due to its poor chemical stability at high temperature. The bending rigidity of the tows and towpregs with two styrene-acrylic sizing agents was measured by cantilever and Kawabata methods. The styrene-acrylic sized towpregs show low torque values, and are suitable for further processing, such as weaving, preforming, and winding. Finally, composite panels were fabricated directly from the towpregs by hot compression molding. Both of the composite panels show superior flexural strength (>400 MPa), flexural modulus (>63 GPa), and interlaminar shear strength (>27 MPa), indicating the applicability of these two styrene-acrylic sizing agents for carbon fiber thermoplastic towpregs.

Effects of Styrene-Acrylic Sizing on the Mechanical Properties of Carbon Fiber Thermoplastic Towpregs and Their Composites

Directory of Open Access Journals (Sweden)

Sean Bowman

2018-03-01

Full Text Available Thermoplastic towpregs are convenient and scalable raw materials for the fabrication of continuous fiber-reinforced thermoplastic matrix composites. In this paper, the potential to employ epoxy and styrene-acrylic sizing agents was evaluated for the making of carbon fiber thermoplastic towpregs via a powder-coating method. The protective effects and thermal stability of these sizing agents were investigated by single fiber tensile test and differential scanning calorimetry (DSC measurement. The results indicate that the epoxy sizing agent provides better protection to carbon fibers, but it cannot be used for thermoplastic towpreg processing due to its poor chemical stability at high temperature. The bending rigidity of the tows and towpregs with two styrene-acrylic sizing agents was measured by cantilever and Kawabata methods. The styrene-acrylic sized towpregs show low torque values, and are suitable for further processing, such as weaving, preforming, and winding. Finally, composite panels were fabricated directly from the towpregs by hot compression molding. Both of the composite panels show superior flexural strength (>400 MPa, flexural modulus (>63 GPa, and interlaminar shear strength (>27 MPa, indicating the applicability of these two styrene-acrylic sizing agents for carbon fiber thermoplastic towpregs.

Mechanical behaviour of wood T-joints. Experimental and numerical investigation

Directory of Open Access Journals (Sweden)

C.L. dos Santos

2015-01-01

Full Text Available Results of a double-shear single-dowel wood connection tested under monotonic quasi-static compression loading are presented and discussed in this paper. The wood used in this study was a pine wood, namely the Pinus pinaster species, which is one of the most important Portuguese species. Each connection (specimen consists of three wood members: a centre member, loaded in compression along the parallel-tograin direction and two simply supported side members, loaded along the perpendicular-to-grain direction (Tconnection. The load transfer between wood members was assured by means of a steel dowel, which is representative of the most common joining technique applied for structural details in wooden structures. The complete load-slip behaviour of the joint is obtained until failure. In particular, the values of the stiffness, the ultimate loads and the ductility were evaluated. Additionally, this investigation proposed non-linear 3D finite element models to simulate the T-joint behaviour. The interaction between the dowel and the wood members was simulated using contact finite elements. A plasticity model, based on Hill’s criterion, was used to simulate the joint ductility and cohesive damage modelling was applied to simulate the brittle failure modes (splitting observed in the side members of the joint. The simulation procedure allowed a satisfactory description of the non-linear behaviour of the T-joint including the collapse prediction.

Characterising the thermoforming behaviour of glass fibre textile reinforced thermoplastic composite materials

Science.gov (United States)

Kuhtz, M.; Maron, B.; Hornig, A.; Müller, M.; Langkamp, A.; Gude, M.

2018-05-01

Textile reinforced thermoplastic composites are predestined for highly automated medium- and high-volume production processes. The presented work focusses on experimental studies of different types of glass fibre reinforced polypropylene (GF-PP) semi-finished thermoplastic textiles to characterise the forming behaviour. The main deformation modes fabric shear, tension, thought-thickness compression and bending are investigated with special emphasis on the impact of the textile structure, the deformation temperature and rate dependency. The understanding of the fundamental forming behaviour is required to allow FEM based assessment and improvement of thermoforming process chains.

Characterization of elastic-viscoplastic properties of an AS4/PEEK thermoplastic composite

Science.gov (United States)

Yoon, K. J.; Sun, C. T.

1991-01-01

The elastic-viscoplastic properties of an AS4/PEEK (APC-2) thermoplastic composite were characterized at 24 C (75 F) and 121 C (250 F) by using a one-parameter viscoplasticity model. To determine the strain-rate effects, uniaxial tension tests were performed on unidirectional off-axis coupon specimens with different monotonic strain rates. A modified Bodner and Partom's model was also used to describe the viscoplasticity of the thermoplastic composite. The experimental results showed that viscoplastic behavior can be characterized quite well using the one-parameter overstress viscoplasticity model.

Heating and ignition of small wood cylinders

Science.gov (United States)

Wallace L. Fons

1950-01-01

The literature provides limited information on the time of ignition of wood under conditions of rapid heating such as occur in forest and structure fires. An investigation was made of ease of ignition as affected by such physical properties of wood as initial temperature, size, and moisture content and by temperature of ambient gas or rate of heating. Temperature-time...

EVOLUTION OF LIGHTWEIGHT WOOD COMPOSITES

Directory of Open Access Journals (Sweden)

Marius C. BARBU

2016-01-01

Full Text Available Lightweight boards and beams in the wood-based construction and furniture industry are not a new topic. The density reduction of panels using sandwich structure with light cores was confirmed by users like doors or mobile homes more than three decades ago. Today many ways to attain a lighter wooden structure are on offer, partially in industrial application. The first one is the use of light-weight wood species like balsa, lime, pine from southern hemisphere plantations etc. limited by the availability, strength properties, gluability and so on. A second one is the sandwich structure made from hard faces like thick veneer, thin plywood, particleboard or high density thin fiberboard and cores made from honeycomb paper, very light wood species or foams like the polystyrene one. A third way to produce a light structure is to reduce the core drastically, using predesigned skeletons with special shapes and connections to the faces. The engines for these developments are on the one hand the fast growing market of knockdown furniture and on the other hand the increasing costs for energy and raw materials. Additional factors that make weight saving a primary economical objective for most producers are transportation costs, easier handling and higher acceptance among the end users. Moreover, customers demand more for ergonomical solutions regarding packaging. Many patents were generated by researchers and developers for new one-stage production processes for sandwich panels with wood- and impregnated paper-based facings made from veneers, particles or fibres and a core consisting of expandable foams, particles or embedded hard skeletons. These ideas or prototypes could be integrated in existing continuous pressing lines for wood based panels keeping some of the advantages of the continuous production technique in matters of efficiency. Some of the challenges of the light weight wooden structure are the connection in half or final parts, resistance to

Waste-wood resource supply assessment. Final report

International Nuclear Information System (INIS)

1991-08-01

The report documents and analyzes the availability and supply of wood waste in New York State to determine the type and amount currently generated to estimate its potential future use as a fuel. Detailed, current information is included on the availability, quantity and price of wood waste. Topics include wood waste markets; the harvesting and supply infrastructure; current and project prices; competing markets; environmental impacts of harvesting, processing and burning wood waste for fuel; and factors affecting long-term availability and supply. New York State's waste wood resource was evaluated to complete the Energy Authority's recent investigation of the potential role of wood in producing electric power. In 1989 approximately 11.8 million tons of wood waste were generated in New York State. More than 8 million tons or 68 percent, were disposed of by municipal solid waste and construction and demolition debris facilities. Just under 3.8 million tons or 32 percent, were reused and/or recycled. More than 25.7 million tons of wood waste could be available annually for fuel. Of the amount, more than 17.2 million tons per year, or 67 percent, could be produced by silvicultural activities that improve the health and productivity of forests

Green composites of thermoplastic corn starch and recycled paper cellulose fibers

Directory of Open Access Journals (Sweden)

Amnuay Wattanakornsiri

2011-08-01

Full Text Available Ecological concerns have resulted in a renewed interest in environmental-friendly composites issues for sustainabledevelopment as a biodegradable renewable resource. In this work we used cellulose fibers from recycled newspaper as reinforcementfor thermoplastic starch in order to improve its mechanical, thermal and water resistance properties. The compositeswere prepared from corn starch plasticized by glycerol (30% wt/wt of glycerol to starch as matrix that was reinforcedwith micro-cellulose fibers, obtained from used newspaper, with fiber content ranging from 0 to 8% (wt/wt of fibers to matrix.Physical properties of composites were determined by mechanical tensile tests, differential scanning calorimetry, thermogravimetricanalysis, water absorption measurement and scanning electron microscopy. The results showed that higherfibers content raised the tensile strength and elastic modulus up to 175% and 292%, respectively, when compared to thenon-reinforced thermoplastic starch. The addition of the fibers improved the thermal resistance and decreased the waterabsorption up to 63%. Besides, scanning electron microscopy illustrated a good adhesion between matrix and fibers. Theseresults indicated that thermoplastic starch reinforced with recycled newspaper cellulose fibers could be fruitfully used ascommodity plastics being strong, cheap, abundant and recyclable.

Introducing wood pellet fuel to the UK

Energy Technology Data Exchange (ETDEWEB)

Cotton, R A; Giffard, A

2001-07-01

Technical and non-technical issues affecting the introduction of wood pellet-fired heating to the UK were investigated with the aim of helping to establish a wood pellet industry in the UK. The project examined the growth and status of the industry in continental Europe and North America, reviewed relevant UK standards and legislation, identified markets for pellet heating in the UK, organised workshops and seminars to demonstrate pellet burning appliances, carried out a trial pelletisation of a range of biomass fuels, helped to set up demonstration installations of pellet-fired appliances, undertook a promotional campaign for wood pellet fuel and compiled resource directories for pellet fuel and pellet burning appliances in the UK. The work was completed in three phases - review, identification and commercialisation. Project outputs include UK voluntary standards for wood pellet fuel and combustion appliances, and a database of individuals with an interest in wood pellet fuel.