WorldWideScience

Sample records for special purpose trucks

  1. The Special Purpose Vehicle

    Fomcenco, Alex

    2013-01-01

    The purpose of this article is to investigate whether the situation where two companies appear as originators or sponsors behind a Special Purpose Vehicle (SPV) can be described as a merger, although on micro scale. Are the underlying grounds behind the creation of an SPV much different than those...

  2. JENDL special purpose file

    Nakagawa, Tsuneo

    1995-01-01

    In JENDL-3,2, the data on all the reactions having significant cross section over the neutron energy from 0.01 meV to 20 MeV are given for 340 nuclides. The object range of application extends widely, such as the neutron engineering, shield and others of fast reactors, thermal neutron reactors and nuclear fusion reactors. This is a general purpose data file. On the contrary to this, the file in which only the data required for a specific application field are collected is called special purpose file. The file for dosimetry is a typical special purpose file. The Nuclear Data Center, Japan Atomic Energy Research Institute, is making ten kinds of JENDL special purpose files. The files, of which the working groups of Sigma Committee are in charge, are listed. As to the format of the files, ENDF format is used similarly to JENDL-3,2. Dosimetry file, activation cross section file, (α, n) reaction data file, fusion file, actinoid file, high energy data file, photonuclear data file, PKA/KERMA file, gas production cross section file and decay data file are described on their contents, the course of development and their verification. Dosimetry file and gas production cross section file have been completed already. As for the others, the expected time of completion is shown. When these files are completed, they are opened to the public. (K.I.)

  3. Selected Special-Purpose Telecommunications Circuits

    Gimble, Thomas

    1994-01-01

    We are providing this memorandum report for your information and use. This report is the first of three reports resulting from the review of requirements for special-purpose voice circuits as part of Project...

  4. Special purpose materials for fusion application

    Scott, J.L.; Clinard, F.W. Jr.; Wiffen, F.W.

    1984-01-01

    Originally in 1978 the Special Purpose Materials Task Group was concerned with tritium breeding materials, coolants, tritium barriers, graphite and silicon carbide, ceramics, heat-sink materials, and magnet components. Since then several other task groups have been created, so now the category includes only materials for superconducting magnets and ceramics. For the former application copper-stabilized Nb 3 Sn (Ti) insulated with polyimides will meet the general requirements, so that testing of prototype components is the priority task. Ceramics are required for several critical components of fusion reactors either as dielectrics or as a structural material. Components near the first wall will receive exposures of 5 to 20 MW.year/m"2. Other ceramic applications are well behind the first wall, with lower damage levels. Most insulators operate near room temperature, but ceramic blanket structures may operate up to 1000 0 C. Because of a meager data base, one cannot identify optimum ceramics for structural application; but MgAl 2 O 4 is an attractive dielectric material

  5. Treecode with a Special-Purpose Processor

    Makino, Junichiro

    1991-08-01

    We describe an implementation of the modified Barnes-Hut tree algorithm for a gravitational N-body calculation on a GRAPE (GRAvity PipE) backend processor. GRAPE is a special-purpose computer for N-body calculations. It receives the positions and masses of particles from a host computer and then calculates the gravitational force at each coordinate specified by the host. To use this GRAPE processor with the hierarchical tree algorithm, the host computer must maintain a list of all nodes that exert force on a particle. If we create this list for each particle of the system at each timestep, the number of floating-point operations on the host and that on GRAPE would become comparable, and the increased speed obtained by using GRAPE would be small. In our modified algorithm, we create a list of nodes for many particles. Thus, the amount of the work required of the host is significantly reduced. This algorithm was originally developed by Barnes in order to vectorize the force calculation on a Cyber 205. With this algorithm, the computing time of the force calculation becomes comparable to that of the tree construction, if the GRAPE backend processor is sufficiently fast. The obtained speed-up factor is 30 to 50 for a RISC-based host computer and GRAPE-1A with a peak speed of 240 Mflops.

  6. SPECIAL PURPOSE SHOCK TUBE for BLAST ASSESSMENT

    Federal Laboratory Consortium — This device is a specially designed shock tube for testing fabric samples in a controlled environment. The device determines the appropriate types of sensors to be...

  7. Breeding of speciality maize for industrial purposes

    Pajić Zorica; Radosavljević Milica; Filipović Milomir; Todorović Goran; Srdić Jelena; Pavlov Milovan

    2010-01-01

    The breeding programme on speciality maize with specific traits was established at the Maize Research Institute, Zemun Polje, several decades ago. The initial material was collected, new methods applying to breeding of speciality maize, i.e. popping maize, sweet maize and white-seeded maize, were introduced. The aim was to enhance and improve variability of the initial material for breeding these three types of maize. Then, inbred lines of good combining abilities were developed and used as c...

  8. 7 CFR 925.54 - Special purpose shipments.

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Special purpose shipments. 925.54 Section 925.54 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing... entering the channels of trade for other than the specific purposes authorized by this section. Inspection...

  9. 50 CFR 21.27 - Special purpose permits.

    2010-10-01

    ... certification required by part 13 and makes a sufficient showing of benefit to the migratory bird resource..., salvage, otherwise acquire, transport, or possess migratory birds, their parts, nests, or eggs for any... WILDLIFE AND PLANTS (CONTINUED) MIGRATORY BIRD PERMITS Specific Permit Provisions § 21.27 Special purpose...

  10. 7 CFR 932.155 - Special purpose shipments.

    2010-01-01

    ... and Regulations § 932.155 Special purpose shipments. (a) The disposition of packaged olives covered by... Service, such packaged olives may be disposed of for use in the production of olive oil or dumped. (2... furnish the committee, upon demand, such evidence of disposition of the packaged olives covered by an...

  11. 12 CFR 202.8 - Special purpose credit programs.

    2010-01-01

    ... requirements of paragraph (a) of this section, a creditor may request and consider information regarding the... the case of financial need. If financial need is one of the criteria under a special purpose credit.... Subject to the provisions of paragraph (b) of this section, the Act and this regulation permit a creditor...

  12. A special purpose simulation language for nuclear power plants

    Saphier, D.

    1980-01-01

    A special purpose block-oriented simulation language, 'The Dynamic Simulator for Nuclear Power Plants' (DSNP), was developed at Argonne National Laboratory. The dominant feature of DSNP is the ability to transform a power plant flowchart or block diagram directly into a simulation program. The user is required to recognize the symbolic DSNP statements for the appropriate physical component, and list these statements in a logical sequence according to the flow of physical properties in the simulated power plant. At present most of the component models in DSNP are of the lumped parameter type. Although DSNP is a special purpose simulation language, it also has all the features of a general purpose simulation language, and in particular a powerful macro processor. The use of DSNP is demonstrated by a sample problem simulating a reactor startup accident. (Auth.)

  13. UTV Expansion Pack: Special-Purpose Rank-Revealing Algorithms

    Fierro, Ricardo D.; Hansen, Per Christian

    2005-01-01

    This collection of Matlab 7.0 software supplements and complements the package UTV Tools from 1999, and includes implementations of special-purpose rank-revealing algorithms developed since the publication of the original package. We provide algorithms for computing and modifying symmetric rank-r...... values of a sparse or structured matrix. These new algorithms have applications in signal processing, optimization and LSI information retrieval.......This collection of Matlab 7.0 software supplements and complements the package UTV Tools from 1999, and includes implementations of special-purpose rank-revealing algorithms developed since the publication of the original package. We provide algorithms for computing and modifying symmetric rank......-revealing VSV decompositions, we expand the algorithms for the ULLV decomposition of a matrix pair to handle interference-type problems with a rank-deficient covariance matrix, and we provide a robust and reliable Lanczos algorithm which - despite its simplicity - is able to capture all the dominant singular...

  14. Special Purpose Materials annual progress report, October 1, 1979

    1980-04-01

    The scope of Special Purpose Materials covers fusion reactor materials problems other than the first-wall and blanket structural materials, which are under the purview of the ADIP, DAFS, and PMI task groups. Components that are considered as special purpose materials include breeding materials, coolants, neutron multipliers, barriers for tritium control, materials for compression and OH coils and waveguides, graphite and SiC, heat-sink materials, ceramics, and materials for high-field (> 10-T) superconducting magnets. It is recognized that there will be numerous materials problems that will arise during the design and construction of large magnetic-fusion energy devices such as the Engineering Test Facility (ETF) and Demonstration Reactor (DEMO). Most of these problems will be specific to a particular design or project and are the responsibility of the project, not the Materials and Radiation Effects Branch. Consequently, the Task Group on Special Purpose Materials has limited its concern to crucial and generic materials problems that must be resolved if magnetic-fusion devices are to succeed. Important areas specifically excluded include low-field (8-T) superconductors, fuels for hybrids, and materials for inertial-confinement devices. These areas may be added in the future when funding permits

  15. A special purpose knowledge-based face localization method

    Hassanat, Ahmad; Jassim, Sabah

    2008-04-01

    This paper is concerned with face localization for visual speech recognition (VSR) system. Face detection and localization have got a great deal of attention in the last few years, because it is an essential pre-processing step in many techniques that handle or deal with faces, (e.g. age, face, gender, race and visual speech recognition). We shall present an efficient method for localization human's faces in video images captured on mobile constrained devices, under a wide variation in lighting conditions. We use a multiphase method that may include all or some of the following steps starting with image pre-processing, followed by a special purpose edge detection, then an image refinement step. The output image will be passed through a discrete wavelet decomposition procedure, and the computed LL sub-band at a certain level will be transformed into a binary image that will be scanned by using a special template to select a number of possible candidate locations. Finally, we fuse the scores from the wavelet step with scores determined by color information for the candidate location and employ a form of fuzzy logic to distinguish face from non-face locations. We shall present results of large number of experiments to demonstrate that the proposed face localization method is efficient and achieve high level of accuracy that outperforms existing general-purpose face detection methods.

  16. Applications for special-purpose minerals at a lunar base

    Ming, Douglas W.

    1992-01-01

    Maintaining a colony on the Moon will require the use of lunar resources to reduce the number of launches necessary to transport goods from the Earth. It may be possible to alter lunar materials to produce minerals or other materials that can be used for applications in life support systems at a lunar base. For example, mild hydrothermal alteration of lunar basaltic glasses can produce special-purpose minerals (e.g., zeolites, smectites, and tobermorites) that in turn may be used in life support, construction, waste renovation, and chemical processes. Zeolites, smectites, and tobermorites have a number of potential applications at a lunar base. Zeolites are hydrated aluminosilicates of alkali and alkaline earth cations that possess infinite, three-dimensional crystal structures. They are further characterized by an ability to hydrate and dehydrate reversibly and to exchange some of their constituent cations, both without major change of structure. Based on their unique absorption, cation exchange, molecular sieving, and catalytic properties, zeolites may be used as a solid support medium for the growth of plants, as an adsorption medium for separation of various gases (e.g., N2 from O2), as catalysts, as molecular sieves, and as a cation exchanger in sewage-effluent treatment, in radioactive waste disposal, and in pollution control. Smectites are crystalline, hydrated 2:1 layered aluminosilicates that also have the ability to exchange some of their constituent cations. Like zeolites, smectites may be used as an adsorption medium for waste renovation, as adsorption sites for important essential plant growth cations in solid support plant growth mediums (i.e., 'soils'), as cation exchangers, and in other important application. Tobermorites are cystalline, hydrated single-chained layered silicates that have cation-exchange and selectivity properties between those of smectites and most zeolites. Tobermorites may be used as a cement in building lunar base structures, as

  17. JENDL special purpose data files and related nuclear data

    Iijima, Shungo

    1989-01-01

    The objectives of JENDL Special Purpose Data Files under development are the applications of nuclear data to the evaluation of the fuel cycle, nuclear activation, and radiation damage. The files in plan consist of 9 types of data, viz., the actinide cross sections, the decay data, the activation cross sections, the (α,n) cross sections, the photo-reaction cross sections, the dosimetry cross sections, the gas production cross sections, the primary knock-on atom spectra and KERMA factors, and the data for standard. The status of the compilation and the evaluation of these data are briefly reviewed. In particular, the features of the data required for the evaluation of the activation cross sections, (α,n) cross sections, photo-reaction cross sections, and PKA data are discussed in some detail. The need for the realistic definition of the scope of the work is emphasized. (author)

  18. Determination of current loads of floating platform for special purposes

    Ma, Guang-ying; Yao, Yun-long; Zhao, Chen-yao

    2017-08-01

    This article studied a new floating offshore platform for special purposes, which was assembled by standard floating modules. The environmental load calculation of the platform is an important part of the research of the ocean platform, which has always been paid attention to by engineers. In addition to wave loads, the wind loads and current loads are also important environmental factors that affect the dynamic response of the offshore platform. The current loads on the bottom structure should not be ignored. By Fluent software, the hydrostatic conditions and external current loads of the platform were calculated in this paper. The coefficient which is independent of the current velocity, namely, current force coefficient, can be fitted through current loads, which can be used for the consequent hydrodynamic and mooring analyses.

  19. Personal characteristics of a law enforcement unit of special purpose

    Vasilenko T.G.

    2017-07-01

    Full Text Available The relevance of the study of the personal characteristics of law enforcement officers due to a significant number of crimes of an aggressive nature, committed by employees of internal Affairs bodies, and the need to develop preventive measures. The purpose of this research is to study peculiarities of the manifestation of progressive and inhibiting aggression personality factors in the structure of law enforcement officers, whose activities directly associated with aggression in the performance of official duties. The study involved 149 employees of special forces of law enforcement are male aged 18 to 35 years. Used a wide battery of psychodiagnostic methods aimed at a comprehensive study of the individual respondents. the data Obtained were analyzed using the method of correlation pleiades. According to the results, was discovered a unique picture of the relationship among personality structures and interaction progressive and deterrent aggression factors with the prevalence of progressive on inhibitory factors in the studied structure.

  20. Special purpose materials. Annual progress report, October 1, 1979

    1980-04-01

    Fusion reactor materials problems other than the first-wall and blanket structural materials are investigated. Components that are considered as special purpose materials include breeding materials, coolants, neutron multipliers, barriers for tritium control, materials for compression and OH coils and waveguides, grahite and SiC, heat-sink materials, ceramics, and materials for high-field (>10-T) superconducting magnets. Radiation-induced conductivity of three forms of Al 2 O 3 was measured as a function of ionizing dose rate and temperature. Increases observed are large enough to affect performance of insulators under some fusion reactor operating conditions. Single-crystal MgAl 2 O 4 was shown to exhibit zero swelling when irradiated to approx. 2 x 10 26 n/m 2 at 925 and 1100 K. This ceramic is resistant to nucleation and growth of defect aggregates, and is not characterized by those microstructural conditions which lead to void formation and swelling in Al 2 O 3 . Fracture toughness of single-crystal Al 2 O 3 was significantly increased by elevated-temperature irradiation to approx. 2 x 10 26 n/m 2 , while that for MgAl 2 O 4 and Y 3 Al 5 O 12 showed little or no change. These results show that ceramics can retain their original resistance to crack propagation after high-dose neutron irradiation

  1. Impact of left lane truck restriction strategies on multilane highways in Louisiana : a literature review.

    2009-04-01

    Truck lane restriction strategies (TLRS) are a means of managing truck traffic on highways by prohibiting trucks from using certain lanes to minimize interaction between trucks and other vehicles. The purpose of this study is to review the literature...

  2. Demands made on high-purity copper for special purposes

    Roettges, D.

    1977-01-01

    The properties (electrical resistivity, residual impurities) of high-purity copper produced on a technical scale are reported as well as its practical applications. The paper discusses a high-oxygen copper (SV) with low residual resistivity at low temperatures and an oxygen-free (hydrogen-stable) copper (BE electronic) with low gas content. The SV quality has been specially developed for use as stabilizer in superconductors while the BE quality is used in high and ultrahigh vacuum. (GSC) [de

  3. 12 CFR 221.5 - Special purpose loans to brokers and dealers.

    2010-01-01

    ... 12 Banks and Banking 3 2010-01-01 2010-01-01 false Special purpose loans to brokers and dealers... FEDERAL RESERVE SYSTEM CREDIT BY BANKS AND PERSONS OTHER THAN BROKERS OR DEALERS FOR THE PURPOSE OF PURCHASING OR CARRYING MARGIN STOCK (REGULATION U) § 221.5 Special purpose loans to brokers and dealers. (a...

  4. 7 CFR 923.54 - Special purpose shipments.

    2010-01-01

    ... Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing... conduct of marketing research and development projects established pursuant to § 923.45. (c) The committee... channels of trade for other than the specific purposes authorized by this section. Such rules, regulations...

  5. Special-Purpose High-Torque Permanent-Magnet Motors

    Doane, George B., III

    1995-01-01

    Permanent-magnet brushless motors that must provide high commanded torques and satisfy unusual heat-removal requirement are developed. Intended for use as thrust-vector-control actuators in large rocket engines. Techniques and concepts used to design improved motors for special terrestrial applications. Conceptual motor design calls for use of rotor containing latest high-energy-product rare-earth permanent magnets so that motor produces required torque while drawing smallest possible currents from power supply. Torque generated by electromagnetic interaction between stator and permanent magnets in rotor when associated electronic circuits applied appropriately temporally and spatially phased currents to stator windings. Phase relationships needed to produce commanded torque computed in response to torque command and to electronically sensed angular position of rotor relative to stator.

  6. A special purpose vehicle for radiological emergency response

    Braeck, K.

    1995-01-01

    The scope of this paper encompasses the design and application of a Contamination Control Station (CCS) Response Vehicle. The vehicle is part of emergency response assets at the Department of Energy Pantex Plant, the nation's final assembly and disassembly point for nuclear weapons. The CCS Response Vehicle was designed to satisfy the need for a rapid deployment of equipment for the setup of a Contamination Control Station. This deployment may be either on the Pantex Plant site, or, if directed by the DOE Albuquerque Operations Office, to any location in the US or worldwide to a site having radioactive contamination and needing response assets of this type. Based on the specialized nature of the vehicle and its mission, certain design criteria must be considered. The vehicle must be air transportable. This criteria alone poses size, weight, and material restrictions due to the transporting aircraft and temperature/pressure variations. This paper first focuses on the overall mission of the vehicle, then highlights some of the design considerations

  7. Constructivism in Teaching English for Special Purposes at Tertiary School

    Anna Y. Polenova

    2017-09-01

    Full Text Available The article looks at some principles of constructivism philosophy and the ways they are realized in ESP teaching at tertiary school. The purpose of this article is to describe constructivist teaching approach in enhancing students’ use of appropriate ESP learning strategies. Constructivism is a theory that emphasizes the active role of students in building understanding and making sense of the information. The constructivist teaching is learner-centered where students are actively involved in knowledge construction rather than passive listeners. Students construct knowledge by transforming, organizing, reorganizing previous knowledge through social interaction in construction of knowledge and understanding. The paper is an attempt to examine the principles of constructivist teaching and learning by providing analysis of features of constructivist theory and the organization of a constructivist classroom.

  8. 77 FR 45921 - Alaskan Fuel Hauling as a Restricted Category Special Purpose Flight Operation

    2012-08-02

    ... operations, each aircraft used to transport fuel will be required to receive FAA certification for the... regulations. The special purpose of Alaskan fuel hauling was considered for aircraft type-certificated under... required for this special purpose. The fuel hauling system must be shown to meet the applicable...

  9. Optimization of shovel-truck system for surface mining

    Ercelebi, S.G.; Bascetin, A. [Istanbul Technical University, Istanbul (Turkey). Mining Engineering Department

    2009-07-15

    In surface mining operations, truck haulage is the largest item in the operating costs, constituting 50 to 60% of the total. In order to reduce this cost, it is necessary to allocate and dispatch the trucks efficiently. This paper describes shovel and truck operation models and optimization approaches for the allocation and dispatching of trucks under various operating conditions. Closed queuing network theory is employed for the allocation of trucks and linear programming for the purpose of truck dispatching to shovels. A case study was applied for the Orhaneli open Pit Coal Mine in Turkey. This approach would provide the capability of estimating system performance measures (mine throughput, mean number of trucks, mean waiting time, etc.) for planning purposes when the truck fleet is composed of identical trucks. A computational study is presented to show how choosing the optimum number of trucks and optimum dispatching policy affect the cost of moving material in a truck-shovel system.

  10. Luggage truck

    Oosterhuis, E.J.; Luttekes, E.; Rijsenbrij, J.C.

    2004-01-01

    The present invention relates to a luggage truck (2) comprising a loading space for luggage and provided with a conveyor belt (14) disposed in the loading space for the supply and removal of luggage, which conveyor belt is at the same time a storage unit for the luggage, wherein the conveyor belts

  11. Impact of regional special purpose local option sales tax (SPLOST) initiatives on county infrastructure.

    2011-10-01

    In response to fiscal constraints on transportation funding and the need to address transportation problems and create regional solutions, Georgia is proposing a 1% regional Special-Purpose Local-Option Sales Tax (SPLOST). To accommodate this initiat...

  12. Prospects of development of land driverless trucks

    Bakhmutov, S.; Saykin, A.; Endachev, D.; Evgrafov, V.; Shagurin, A.; Kulikov, I.; Fedoseev, K.

    2018-02-01

    The paper is dedicated to the problem of creation and efficient use of driverless trucks. It also contains general analysis of foreign experience and development trends. The concept of FSUE “NAMI” for development of a platoon of driverless trucks for cargo transportation between specialized terminals on public roads is provided. A road train with virtual couplings where the lead vehicle has a driver and the rest are driverless is proposed as a base for the driverless platoon. The platoon is formed by such road trains, which ensures extended functional features, including the possibility to form platoons of road trains from different logistics centers and with different destinations, quick reforming of the platoon in the logistics centers, possibility to split the platoon when driving on public roads, higher precision of control over the platoon during driving, etc. It is also shown that in order to improve the efficiency of cargo transportation, driverless cargo platforms (trucks) shall be designed without a cabin. The paper also considers the ways to reduce the price of driverless trucks by creating a special road infrastructure, which will allow transfer of the most expensive subsystems of driverless vehicles to such infrastructure. Upon that, the following subsystems will remain within the driverless chassis: navigation, communication, chassis control and ADAS. It is noted that creation of such infrastructure will require high investments, therefore, gradual implementation of such systems is seen as rational. It is shown that the most appropriate area for these purposes is transregional cargo transportation. It is noted that the economic reasons for implementation of the proposed concept are as follows: significant reduction of the number of drivers; significant simplification of the driverless platform control system and reduction of the price of subsystems; no need for the driver’s cabin within the driverless platform; fuel economy when driving within a

  13. Numerical calculation of the conductivity of percolation clusters and the use of special purpose computers

    Herrmann, H.J.

    1989-01-01

    Electrical conductivity diffusion or phonons, have an anomalous behaviour on percolation clusters at the percolation threshold due to the fractality of these clusters. The results that have been found numerically for this anomalous behaviour are reviewed. A special purpose computer built for this purpose is described and the evaluation of the data from this machine is discussed

  14. Lift truck safety review

    Cadwallader, L.C.

    1997-03-01

    This report presents safety information about powered industrial trucks. The basic lift truck, the counterbalanced sit down rider truck, is the primary focus of the report. Lift truck engineering is briefly described, then a hazard analysis is performed on the lift truck. Case histories and accident statistics are also given. Rules and regulations about lift trucks, such as the US Occupational Safety an Health Administration laws and the Underwriter's Laboratories standards, are discussed. Safety issues with lift trucks are reviewed, and lift truck safety and reliability are discussed. Some quantitative reliability values are given

  15. Lift truck safety review

    Cadwallader, L.C.

    1997-03-01

    This report presents safety information about powered industrial trucks. The basic lift truck, the counterbalanced sit down rider truck, is the primary focus of the report. Lift truck engineering is briefly described, then a hazard analysis is performed on the lift truck. Case histories and accident statistics are also given. Rules and regulations about lift trucks, such as the US Occupational Safety an Health Administration laws and the Underwriter`s Laboratories standards, are discussed. Safety issues with lift trucks are reviewed, and lift truck safety and reliability are discussed. Some quantitative reliability values are given.

  16. Fourth annual progress report on special-purpose materials for magnetically confined fusion reactors

    1982-08-01

    The scope of Special Purpose Materials covers fusion reactor materials problems other than the first-wall and blanket structural materials, which are under the purview of the ADIP, DAFS, and PMI task groups. Components that are considered as special purpose materials include breeding materials, coolants, neutron multipliers, barriers for tritium control, materials for compression and OH coils and waveguides, graphite and SiC, heat-sink materials, ceramics, and materials for high-field (>10-T) superconducting magnets. The Task Group on Special Purpose Materials has limited its concern to crucial and generic materials problems that must be resolved if magnetic-fusion devices are to succeed. Important areas specifically excluded include low-field (8-T) superconductors, fuels for hybrids, and materials for inertial-confinement devices. These areas may be added in the future when funding permits

  17. Tokamak Fusion Core Experiment (TFCX) special-purpose remote maintenance systems

    Masson, L.S.; Welland, H.J.

    1985-01-01

    A key element in the preconceptual design of the Tokamak Fusion Core Experiment (TFCX) was the development of design concepts for special-purpose remote maintenance systems. Included were systems for shield sector replacement, vacuum vessel sector and toroidal field coil replacement, limiter blade replacement, protective tile replacement, and general-purpose maintenance. This paper addresses these systems as they apply to the copper toroidal field (TF) coil version of the TFCX

  18. What Is the Purpose? Reflections on Inclusion and Special Education from a Capability Perspective

    Reindal, Solveig Magnus

    2010-01-01

    This article investigated what the capability approach developed by Amartya Sen and Martha Nussbaum can contribute to the issue of inclusion as a new theoretical framework for special education. By posing the question: "What is the purpose of inclusion?", I have proposed to answer this query by investigating how the capability approach is able to…

  19. Indexing, learning and content-based retrieval for special purpose image databases

    M.J. Huiskes (Mark); E.J. Pauwels (Eric)

    2005-01-01

    textabstractThis chapter deals with content-based image retrieval in special purpose image databases. As image data is amassed ever more effortlessly, building efficient systems for searching and browsing of image databases becomes increasingly urgent. We provide an overview of the current

  20. 7 CFR 905.148 - Reports of special purpose shipments under certificates of privilege.

    2010-01-01

    ... (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and Orders; Fruits, Vegetables, Nuts... Regulations Non-Regulated Fruit § 905.148 Reports of special purpose shipments under certificates of privilege... name and address of the shipper or shippers; name and address of the certified organic Florida citrus...

  1. 77 FR 1501 - Special Purpose Permit Application; Draft Environmental Assessment; Hawaii-Based Shallow-Set...

    2012-01-10

    ...-FF01M01000] Special Purpose Permit Application; Draft Environmental Assessment; Hawaii-Based Shallow-Set... the operation of the Hawaii-based shallow-set longline fishery that targets swordfish (Xiphias gladius... albatross, by NMFS in its regulation of the shallow-set longline fishery based in Hawaii. This fishery...

  2. 77 FR 50153 - Special Purpose Permit Application; Hawaii-Based Shallow-Set Longline Fishery; Final...

    2012-08-20

    ...-FF01M01000] Special Purpose Permit Application; Hawaii-Based Shallow-Set Longline Fishery; Final... of the Hawaii-based shallow-set longline fishery, which targets swordfish. After evaluating several... take of seabirds in the shallow-set longline fishery based in Hawaii. The analysis of alternatives is...

  3. Architecture and program structures for a special purpose finite element computer

    Norrie, D.H.; Norrie, C.W.

    1983-01-01

    The development of very large scale integration (VLSI) has made special-purpose computers economically possible. With such a machine, the loss of flexibility compared with a general-purpose computer can be offset by the increased speed which can be obtained by tailoring the architecture to the particular problem or class of problem. The first kind of special-purpose machine has its architecture modelled on the physical structure of the problem and the second kind has its design tailored to the computational algorithm used. The parallel finite element machine (PARFEM) being designed at the University of Calgary for the solution of finite element problems is of the second kind. Its conceptual design is described and progress to date outlined. 14 references.

  4. Business plan for Gourmet Food Truck in Helsinki

    Mulmi, Mukesh

    2015-01-01

    This thesis work is about food truck and food truck industry in Finland. In Finland, Culinary scenes are booming and growing but, the food truck concept is new to Finland. Food truck industry is very young and currently, there is a hype for food truck and people are admiring new cuisines. Author himself is working as a cook. And he is passionate about food and restaurant industry. The main purpose of the thesis was to explore more about food truck industry in Finland and create the busine...

  5. 41 CFR 102-73.170 - What types of special purpose space may the Department of Agriculture lease?

    2010-07-01

    ... purpose space may the Department of Agriculture lease? 102-73.170 Section 102-73.170 Public Contracts and... § 102-73.170 What types of special purpose space may the Department of Agriculture lease? The Department of Agriculture is delegated the authority to lease the following types of special purpose space: (a...

  6. VARIABILITY OF AMYLOSE AND AMYLOPECTIN IN WINTER WHEAT AND SELECTION FOR SPECIAL PURPOSES

    Nikolina Weg Krstičević

    2015-06-01

    Full Text Available The aim of this study was to investigate the variability of amylose and amylopectin in 24 Croatian and six foreign winter wheat varieties and to detect the potential of these varieties for special purposes. Starch composition analysis was based on the separation of amylose and amylopectin and the determination of their amounts and ratios. Analysis of the amount of amylose and amylopectin determined statistically highly significant differences between the varieties. The tested varieties are mostly bread wheat of different quality which have the usual content of amylose and amylopectin. Some varieties were identified among them with high amylopectin and low amylose content and one variety with high amylose content. They have the potential in future breeding programs and selection for special purposes.

  7. Special-purpose interactive programming shell for the open-quotes POLEclose quotes system

    Rvachev, V.L.; Kurpa, L.I.

    1995-01-01

    The development of the theory of R-functions has stimulated the emergence of efficient numerical-analytical methods for a wide class of problems associated with physico-mechanical fields. R-functions are the basis for computer-aided level source language, which is sufficiently close to an ordinary mathematical language. Despite the powerful capabilities of the POLE family systems and the extensive support for the analysis of computation results, these systems are still not widely used in practice, as they assume a user with special mathematical qualifications. It is therefore necessary to develop special-purpose systems that do not require the user to be proficient in mathematical physics, the theory of R-functions, variational methods, etc. In other words, we need systems that are oriented toward technical-profile engineers specializing in design and calculations. In this article, we propose some principles for the construction of a special-purpose interactive programming system POLE-PLAST capable of solving problems in the mechanics of deformable solids of complex shape. As the specific application domain for the description of the system we have chosen problems that deal with bending, stability, and vibration of elements of thin-walled constructions modeled by thin plates

  8. Design of special purpose database for credit cooperation bank business processing network system

    Yu, Yongling; Zong, Sisheng; Shi, Jinfa

    2011-12-01

    With the popularization of e-finance in the city, the construction of e-finance is transfering to the vast rural market, and quickly to develop in depth. Developing the business processing network system suitable for the rural credit cooperative Banks can make business processing conveniently, and have a good application prospect. In this paper, We analyse the necessity of adopting special purpose distributed database in Credit Cooperation Band System, give corresponding distributed database system structure , design the specical purpose database and interface technology . The application in Tongbai Rural Credit Cooperatives has shown that system has better performance and higher efficiency.

  9. Shaping the Strength of Cast Rocker Arm for Special Purpose Vehicle

    Żuczek R.; Pysz S.; Maj M.; Piekło J.

    2015-01-01

    The article discusses the weldment to casting conversion process of rocker arm designed for operation in a special purpose vehicle to obtain a consistency of objective functions, which assume the reduced weight of component, the reduced maximum effort of material under the impact of service loads achieved through topology modification for optimum strength distribution in the sensitive areas, and the development of rocker arm manufacturing technology. As a result of conducted studies, the unit...

  10. Fatigue analysis of assembled marine floating platform for special purposes under complex water environments

    Ma, Guang-ying; Yao, Yun-long

    2018-03-01

    In this paper, the fatigue lives of a new type of assembled marine floating platform for special purposes were studied. Firstly, by using ANSYS AQWA software, the hydrodynamic model of the platform was established. Secondly, the structural stresses under alternating change loads were calculated under complex water environments, such as wind, wave, current and ice. The minimum fatigue lives were obtained under different working conditions. The analysis results showed that the fatigue life of the platform structure can meet the requirements

  11. INTEGRATION OF INFORMATION AND COMMUNICATION TECHNOLOGIES IN TEACHING RUSSIAN AS A FOREIGN LANGUAGE FOR SPECIAL PURPOSES

    Sergey S. Chromov; Nadezda A. Gulayeva; Irina S. Zelenetskaya

    2015-01-01

    The paper is untended to draw attention to information communication technologiesin teaching Russian as a foreign language for special purposes at level B 2. In thisregard the educational process of teaching Russian as a foreign language is examinedfor promoting quality improvement in the process of ELT.Technology-enhances language learning(TELL) is described through computer-assisted language learning(CALL)-presentations, webinars, videolectures. The authors share their experience obtained d...

  12. The future of languages for special purposes in the era of progressing management

    Jurin, Suzana

    2007-01-01

    The authors will give some definitions of the language of special purposes used in multinational business, and they will also describe some characteristics of this language on the morphological level and the level of word-formation. The corpora they are using for this analysis is the corpora found in management reports of German multinational companies. Through this analysis, the authors trace the development of such a language and they observe specific models used in management reports...

  13. Special-purpose materials for magnetically confined fusion reactors. Third annual progress report

    1981-11-01

    The scope of Special Purpose Materials covers fusion reactor materials problems other than the first-wall and blanket structural materials, which are under the purview of the ADIP, DAFS, and PMI task groups. Components that are considered as special purpose materials include breeding materials, coolants, neutron multipliers, barriers for tritium control, materials for compression and OH coils and waveguides, graphite and SiC, heat-sink materials, ceramics, and materials for high-field (>10-T) superconducting magnets. It is recognized that there will be numerous materials problems that will arise during the design and construction of large magnetic-fusion energy devices such as the Engineering Test Facility (ETF) and Demonstration Reactor (DEMO). Most of these problems will be specific to a particular design or project and are the responsibility of the project, not the Materials and Radiation Effects Branch. Consequently, the Task Group on Special Purpose Materials has limited its concern to crucial and generic materials problems that must be resolved if magnetic-fusion devices are to succeed. Important areas specifically excluded include low-field (8-T) superconductors, fuels for hybrids, and materials for inertial-confinement devices. These areas may be added in the future when funding permits

  14. Use of the water supply system of special purpose in buildings

    Orlov Evgeniy Vladimirovich

    Full Text Available A water supply system of a special purpose is a necessary element in hot and cold shops of the industrial enterprises, office buildings and the medical centers, and also other rooms. The water supply systems of a special purpose, which give subsalty, sparkling water and water sated with oxygen, allow people to prevent, for example, strong dehydration of an organism, which is possible at big losses of water, especially in case of the people working in hot shops. Various elements of special drinking water supply system are given in the article, their main functions are described. Different types of the water folding devices pumping water to consumers, one of which is drinking fountain, are considered. Possible systems of water filtration, which can be established for quality improvement, are transferred. Among them the great role is played by membrane technologies and the return osmosis, which is widely applied now. Today there is a possibility of construction, both the centralized water supply system of a special purpose, and local. Besides, the least is a more preferable option taking into account capital expenditure for construction and operation, and also it can lead to solid resource-saving as a result of the electric energy saving going for water heating in heaters. Automatic machines of drinking water for a local water supply system of a special purpose have indisputable advantages. They are capable to carry out several functions at the same time, and also to distribute water to consumers. It allows placing all the necessary equipment, which will be well in harmony with the environment in their small and compact case, and will fit into any difficult interior of the room. Also they are very easily connected to the systems of an internal water supply system by means of a propylene tube that allows to change their sposition in space and to transfer to any place of the room with fast installation of equipment. Also the ecological effect was

  15. A special purpose computer for the calculation of the electric conductivity of a random resistor network

    Hajjar, Mansour

    1987-01-01

    The special purpose computer PERCOLA is designed for long numerical simulations on a percolation problem in Statistical Mechanics of disordered media. Our aim is to improve the actual values of the critical exponents characterizing the behaviour of random resistance networks at percolation threshold. The architecture of PERCOLA is based on an efficient iterative algorithm used to compute the electric conductivity of such networks. The calculator has the characteristics of a general purpose 64 bits floating point micro-programmable computer that can run programs for various types of problems with a peak performance of 25 Mflops. This high computing speed is a result of the pipeline architecture based on internal parallelism and separately micro-code controlled units such as: data memories, a micro-code memory, ALUs and multipliers (both WEITEK components), various data paths, a sequencer (ANALOG DEVICES component), address generators and a random number generator. Thus, the special purpose computer runs percolation problem program 10 percent faster than the supercomputer CRAY XMP. (author) [fr

  16. High-speed BWR power plant simulations on the special-purpose peripheral processor AD10

    Wulff, W.; Cheng, H.S.; Lekach, S.V.; Mallen, A.N.

    1985-01-01

    A newly developed technique is described for fast, on-line simulations of normal and accidental transients in nuclear power plants. The technique is based on the utilization of the special-purpose peripheral processor AD10, which is specifically designed for high-speed systems simulations through integration of large systems of nonlinear ordinary differential equations. The Peach Bottom-II Boiling Water Reactor power plant has been simulated and results are presented. It is shown that the new technique not only advances safety analyses but also supports plant monitoring, failure diagnosis and accident mitigation, as well as the training of nuclear power plant operators. (author)

  17. Shaping the Strength of Cast Rocker Arm for Special Purpose Vehicle

    Żuczek R.

    2015-09-01

    Full Text Available The article discusses the weldment to casting conversion process of rocker arm designed for operation in a special purpose vehicle to obtain a consistency of objective functions, which assume the reduced weight of component, the reduced maximum effort of material under the impact of service loads achieved through topology modification for optimum strength distribution in the sensitive areas, and the development of rocker arm manufacturing technology. As a result of conducted studies, the unit weight of the item was reduced by 25%, and the stress limit values were reduced to a level guaranteeing safe application.

  18. GRAPE-5: A Special-Purpose Computer for N-body Simulation

    Kawai, Atsushi; Fukushige, Toshiyuki; Makino, Junichiro; Taiji, Makoto

    1999-01-01

    We have developed a special-purpose computer for gravitational many-body simulations, GRAPE-5. GRAPE-5 is the successor of GRAPE-3. Both consist of eight custom pipeline chips (G5 chip and GRAPE chip). The difference between GRAPE-5 and GRAPE-3 are: (1) The G5 chip contains two pipelines operating at 80 MHz, while the GRAPE chip had one at 20 MHz. Thus, the calculation speed of the G5 chip and that of GRAPE-5 board are 8 times faster than that of GRAPE chip and GRAPE-3 board. (2) The GRAPE-5 ...

  19. Hydrodynamic analysis of floating platform for special purposes under complex water environment

    Ma, Guang-ying; Yao, Yun-long

    2018-03-01

    This article studied a new floating offshore platform for special purposes, which was assembled by standard floating modules. By using ANSYS AQWA software, the hydrodynamic model of the platform was established. The time history responses of the platform motions and the cable tension forces were calculate under complex water environments, such as wind, wave, current and mooring. The results showed that the tension of the four cables are far less than the breaking tension of the cable, so that the cable will not break. This study can be referenced by the relevant researchers and engineers.

  20. Selection and optimization of mooring cables on floating platform for special purposes

    Ma, Guang-ying; Yao, Yun-long; Zhao, Chen-yao

    2017-08-01

    This paper studied a new type of assembled marine floating platform for special purposes. The selection and optimization of mooring cables on the floating platform are studied. By using ANSYS AQWA software, the hydrodynamic model of the platform was established to calculate the time history response of the platform motion under complex water environments, such as wind, wave, current and mooring. On this basis, motion response and cable tension were calculated with different cable mooring states under the designed environmental load. Finally, the best mooring scheme to meet the cable strength requirements was proposed, which can lower the motion amplitude of the platform effectively.

  1. Scheduling trucks in cross docking systems with temporary storage and dock repeat truck holding pattern using genetic algorithm

    Ehsan Ghobadian

    2013-02-01

    Full Text Available Cross docking is one of the most important issues in management of supply chains. In cross docking, different items delivered to a warehouse by inbound trucks are directly arranged and reorganized based on customer demands, routed and loaded into outbound trucks for delivery purposes to customers without virtually keeping them at the warehouse. If any item is kept in storage, it is normally for a short amount of time, say less than 24 hours. In this paper, we consider a special case of cross docking where there is temporary storage and implements genetic algorithm to solve the resulted problem for some realistic test problems. In our method, we first use some heuristics as initial solutions and then improve the final solution using genetic algorithm. The performance of the proposed model is compared with alternative solution strategy, the GRASP method.

  2. Special Purpose Nuclear Reactor (5 MW) for Reliable Power at Remote Sites Assessment Report

    Sterbentz, James William [Idaho National Lab. (INL), Idaho Falls, ID (United States). Nuclear Science and Technology Division; Werner, James Elmer [Idaho National Lab. (INL), Idaho Falls, ID (United States). Nuclear Science and Technology Division; McKellar, Michael George [Idaho National Lab. (INL), Idaho Falls, ID (United States). Nuclear Science and Technology Division; Hummel, Andrew John [Idaho National Lab. (INL), Idaho Falls, ID (United States). Nuclear Science and Technology Division; Kennedy, John Charles [Idaho National Lab. (INL), Idaho Falls, ID (United States). Nuclear Science and Technology Division; Wright, Richard Neil [Idaho National Lab. (INL), Idaho Falls, ID (United States). Nuclear Science and Technology Division; Biersdorf, John Michael [Idaho National Lab. (INL), Idaho Falls, ID (United States). Nuclear Science and Technology Division

    2017-04-01

    The Phenomena Identification and Ranking Table (PIRT) technique was conducted on the Special Purpose Reactor nuclear plant design. The PIRT is a structured process to identify safety-relevant/safety-significant phenomena and assess the importance and knowledge base by ranking the phenomena. The Special Purpose Reactor is currently in the conceptual design stage. The candidate reactor has a solid monolithic stainless steel core with an array of heat pipes and fuel pellets embedded in the monolith. The heat pipes are used to remove heat from the core using simple, reliable, and well-characterized physics (capillarity, boiling, and condensation). In the initial design, one heat exchanger is used for the working fluid that produces energy, and a second heat exchanger is used to remove decay heat in emergency or shutdown conditions. In addition, a power conversion cycle such as an open-air Brayton system is available as an option for power conversion and process heat. This report summarizes and documents the process and scope of the four PIRT reviews, noting the major activities and conclusions. The identified phenomena, analyses, rationales, and associated ratings are presented along with a summary of the findings from the four individual PIRTs, namely (1) Reactor Accident and Normal Operations, (2) Heat Pipes, (3) Materials, and (4) Power Conversion. The PIRT reports for these four major system areas evaluated are attached as appendixes to this report and provide considerably more detail about each assessment as well as a more complete listing of the phenomena that were evaluated.

  3. Nuclear data libraries for gamma analysis programs, including special purpose libraries

    Westmeier, W.; Reus, U.; Siemon, K.; Westmeier, H.

    2002-01-01

    A complete set of gamma ray and other data relating to the decay of all known nuclides has been compiled from the literature and electronic sources. The data were critically reviewed, evaluated and the consistency was checked. The total catalogue is comprised of data-sets for 3841 nuclides and isomers with 106,355 gamma ray and 19,347 X ray entries. A subset of 1,627 nuclides with 32,456 gamma ray entries is extracted into a database, which provides the basis for the generation of nuclide libraries for the application in spectrometry programmes. The WINDOWS based program NUC M AN was developed which serves for the updating and editing of the database as well as the generation of task-specific user libraries for special purposes. The literature cut-off date for this catalogue is January 1, 1998. (author)

  4. On the Equivalence of Tank Trucks and General Purpose Trucks ...

    ... which is the subdividing of the overall market into homogeneous subsets of customers where any subset(s) may be selected as a target market to be reached with a distinct marketing mix. But the fact that different segments can be identified with particular kinds of vehicles or type of products, suggests that there are natural ...

  5. Kogi Truck Culture

    Choy, Vivian

    2011-01-01

    Food trucks have become a large phenomenon in many parts of Southern California. In fact, the University of California, Los Angeles had begun permitting several food trucks to park on campus for hungry students, in response to the closure of the Bombshelter, a major campus food court. These trucks’ budding popularity has been spurred by the notable Kogi Trucks, which began its business serving those in Los Angeles. To explore the heart of this Kogi hype, I took two trips to the intersectio...

  6. 37 CFR 201.15 - Special handling of pending claims requiring expedited processing for purposes of litigation.

    2010-07-01

    ... 37 Patents, Trademarks, and Copyrights 1 2010-07-01 2010-07-01 false Special handling of pending... PROVISIONS § 201.15 Special handling of pending claims requiring expedited processing for purposes of... compelling need for the service exists due to pending or prospective litigation, customs matters, or contract...

  7. Features of applying systems approach for evaluating the reliability of cryogenic systems for special purposes

    E. D. Chertov

    2016-01-01

    Full Text Available Summary. The analysis of cryogenic installations confirms objective regularity of increase in amount of the tasks solved by systems of a special purpose. One of the most important directions of development of a cryogenics is creation of installations for air separation product receipt, namely oxygen and nitrogen. Modern aviation complexes require use of these gases in large numbers as in gaseous, and in the liquid state. The onboard gas systems applied in aircraft of the Russian Federation are subdivided on: oxygen system; air (nitric system; system of neutral gas; fire-proof system. Technological schemes ADI are in many respects determined by pressure of compressed air or, in a general sense, a refrigerating cycle. For the majority ADI a working body of a refrigerating cycle the divided air is, that is technological and refrigerating cycles in installation are integrated. By this principle differentiate installations: low pressure; average and high pressure; with detander; with preliminary chilling. There is also insignificant number of the ADI types in which refrigerating and technological cycles are separated. These are installations with external chilling. For the solution of tasks of control of technical condition of the BRV hardware in real time and estimates of indicators of reliability it is offered to use multi-agent technologies. Multi-agent approach is the most acceptable for creation of SPPR for reliability assessment as allows: to redistribute processing of information on elements of system that leads to increase in overall performance; to solve a problem of accumulating, storage and recycling of knowledge that will allow to increase significantly efficiency of the solution of tasks of an assessment of reliability; to considerably reduce intervention of the person in process of functioning of system that will save time of the person of the making decision (PMD and will not demand from it special skills of work with it.

  8. Assessment of efficiency of functioning the infocommunication systems a special purpose in the conditions of violation quality of relevance information

    Parinov, A. V.; Korotkikh, L. P.; Desyatov, D. B.; Stepanov, L. V.

    2018-03-01

    The uniqueness of information processing mechanisms in special-purpose infocommunication systems and the increased interest of intruders lead to an increase in the relevance of the problems associated with their protection. The paper considers the issues of building risk-models for the violation of the relevance and value of information in infocommunication systems for special purposes. Also, special attention is paid to the connection between the qualities of relevance and the value of information obtained as a result of the operation of infocommunication systems for special purposes. Analytical expressions for the risk and damage function in the time range in special-purpose infocommunication systems are obtained, which can serve as a mathematical basis for risk assessment. Further, an analytical expression is obtained to assess the chance of obtaining up-to-date information in the operation of infocommunication systems up to the time the information quality is violated. An analytical expression for estimating the chance can be used to calculate the effectiveness of a special-purpose infocommunication system.

  9. Acceptance test procedure for core sample trucks

    Smalley, J.L.

    1995-01-01

    The purpose of this Acceptance Test Procedure is to provide instruction and documentation for acceptance testing of the rotary mode core sample trucks, HO-68K-4600 and HO-68K-4647. The rotary mode core sample trucks were based upon the design of the second core sample truck (HO-68K-4345) which was constructed to implement rotary mode sampling of the waste tanks at Hanford. Acceptance testing of the rotary mode core sample trucks will verify that the design requirements have been met. All testing will be non-radioactive and stand-in materials shall be used to simulate waste tank conditions. Compressed air will be substituted for nitrogen during the majority of testing, with nitrogen being used only for flow characterization

  10. MDGRAPE-4: a special-purpose computer system for molecular dynamics simulations.

    Ohmura, Itta; Morimoto, Gentaro; Ohno, Yousuke; Hasegawa, Aki; Taiji, Makoto

    2014-08-06

    We are developing the MDGRAPE-4, a special-purpose computer system for molecular dynamics (MD) simulations. MDGRAPE-4 is designed to achieve strong scalability for protein MD simulations through the integration of general-purpose cores, dedicated pipelines, memory banks and network interfaces (NIFs) to create a system on chip (SoC). Each SoC has 64 dedicated pipelines that are used for non-bonded force calculations and run at 0.8 GHz. Additionally, it has 65 Tensilica Xtensa LX cores with single-precision floating-point units that are used for other calculations and run at 0.6 GHz. At peak performance levels, each SoC can evaluate 51.2 G interactions per second. It also has 1.8 MB of embedded shared memory banks and six network units with a peak bandwidth of 7.2 GB s(-1) for the three-dimensional torus network. The system consists of 512 (8×8×8) SoCs in total, which are mounted on 64 node modules with eight SoCs. The optical transmitters/receivers are used for internode communication. The expected maximum power consumption is 50 kW. While MDGRAPE-4 software has still been improved, we plan to run MD simulations on MDGRAPE-4 in 2014. The MDGRAPE-4 system will enable long-time molecular dynamics simulations of small systems. It is also useful for multiscale molecular simulations where the particle simulation parts often become bottlenecks.

  11. Mathematical and numerical models to achieve high speed with special-purpose parallel processors

    Cheng, H.S.; Wulff, W.; Mallen, A.N.

    1986-01-01

    Historically, safety analyses and plant dynamic simulations have been and still are being carried out be means of detailed FORTRAN codes on expensive mainframe computers in time-consuming batch processing mode. These codes have grown to be so expensive to execute that their utilization depends increasingly on the availability of very expensive supercomputers. Thus, advanced technology for high-speed, low-cost, and accurate plant dynamic simulations is very much needed. Ideally, a low-cost facility based on a modern minicomputer can be dedicated to the staff of a power plant, which is easy and convenient to use, and which can simulate realistically plant transients at faster than real-time speeds. Such a simulation capability can enhance safety and plant utilization. One such simulation facility that has been developed is the Brookhaven National Laboratory (BNL) Plant Analyzer, currently set up for boiling water reactor plant simulations at up to seven times faster than real-time process speeds. The principal hardware components of the BNL Plant Analyzer are two units of special-purpose parallel processors, the AD10 of Applied Dynamics International and a PDP-11/34 host computer

  12. Application of food irradiation technology in development of future special purposed foods

    Byun, Myung Woo; Shin, Myung Gon [Woosong University, Daejeon (Korea, Republic of); Lee, Ju Woon [Korea Atomic Energy Research Institute, Jeongeup (Korea, Republic of)

    2010-06-15

    Advanced food technologies fused with radiation technology could be applied to the development of various special-purpose foods such space foods, combat rations, emergency foods, and sterile patient meals. In U.S.A, the National Aeronautics and Space Administration and the U.S. Army Natick Soldier RD and E Center co-developed the hazard analysis of critical control point, which is a essential hygienic control system in food industry. Moreover, strict manufacturing standards to produce shelf-stable foods using radiation (ionizing energy) technology were established. In Korea, the advanced food technologies to sterilize various foods using irradiation technology were expected to be applied as a hygiene process on group meals and ready-to-eat/ready-to cook foods, and to produce foods for patients with high hygienic, nutritional, and organoleptic qualities through the combination treatments with irradiation technology. And, it was considered that the advanced technology would improve the related industries and national economy by introducing the food irradiation technology to the Korean traditional fermented foods to improve their functionality. In conclusion, the advanced food technologies which are preoccupied by some developed countries like U.S.A. and Russia will make a contribution to the development of national science and technology, and competitiveness promotion of industry.

  13. Application of food irradiation technology in development of future special purposed foods

    Byun, Myung Woo; Shin, Myung Gon; Lee, Ju Woon

    2010-01-01

    Advanced food technologies fused with radiation technology could be applied to the development of various special-purpose foods such space foods, combat rations, emergency foods, and sterile patient meals. In U.S.A, the National Aeronautics and Space Administration and the U.S. Army Natick Soldier RD and E Center co-developed the hazard analysis of critical control point, which is a essential hygienic control system in food industry. Moreover, strict manufacturing standards to produce shelf-stable foods using radiation (ionizing energy) technology were established. In Korea, the advanced food technologies to sterilize various foods using irradiation technology were expected to be applied as a hygiene process on group meals and ready-to-eat/ready-to cook foods, and to produce foods for patients with high hygienic, nutritional, and organoleptic qualities through the combination treatments with irradiation technology. And, it was considered that the advanced technology would improve the related industries and national economy by introducing the food irradiation technology to the Korean traditional fermented foods to improve their functionality. In conclusion, the advanced food technologies which are preoccupied by some developed countries like U.S.A. and Russia will make a contribution to the development of national science and technology, and competitiveness promotion of industry

  14. Use of high dose irradiation for development of special purposed foods

    Yoon, Yohan; Lee, Ju-Woon

    2009-01-01

    Full text: FAO/WHO Food Safety Committee indicated that food borne disease is one of the most widespread threats to human health and is ever increasing, which requires a national measure against the problems in public health and consequent economic productivity. The increasing demand for convenient foods as well as safer foods needs new technologies with potentials to solve or complement the limitations of existing methods for preserving and improving the food quality and safety. There are various techniques for preserving foods, most of which have problems in terms of effectiveness, quality, safety, economic feasibility, and environmental impact. Food irradiation has been studied more extensively and scientifically than any other food processing technologies. It is a physical method for food treatment comparable to heat pasteurization, canning or freezing. The process involves exposing foods, either packaged or in bulk, to one of three types of ionizing energy: gamma rays, machine-generated electrons or X-rays. Food irradiation is a promising food safety technology that can eliminate spoilage and pathogens from foods. However, low consumer acceptance of irradiated foods has been become an obstacle to make food irradiation technology as widely accepted method. Thus, use of the technology in development of special-purposed foods should be a first step to make irradiation technology as a common decontamination method in food industry. Korea Atomic Energy Research Institute (KAERI) has used irradiation technology to develop space foods for astronauts, and four Korean foods (Kimchi: fermented vegetable, Ramen: ready-to-cook noodles, Saengshik bar: raw grain bar, Sujeonggwa: cinnamon beverage) were certificated by Institute of Biomedical Problems, followed by sensory and quality evaluation in International Space Stations. With this previous research experience, KAERI has researched on development of patient foods and military rations. Hospital patients are a special

  15. Simulations of diocotron instability using a special-purpose computer, MDGRAPE-2

    Yatsuyanagi, Yuichi; Kiwamoto, Yasuhito; Ebisuzaki, Toshikazu; Hatori, Tadatsugu; Kato, Tomokazu

    2003-01-01

    The diocotron instability in a low-density non-neutral electron plasma is examined via numerical simulations. For the simulations, a current-vortex filament model and a special-purpose computer, MDGRAPE-2 are used. In the previous work, a simulation method based on the current-vortex filament model, which is called 'current-vortex method', is developed. It is assumed that electric current and vorticity have discontinuous filamentary distributions, and both point electric current and point vortex are confined in a filament, which is called 'current-vortex filament'. In this paper, the current-vortex method with no electric current is applied to simulations of the non-neutral electron plasma. This is equivalent to the traditional point-vortex method. MDGRAPE-2 was originally designed for molecular dynamics simulations. It accelerates calculations of the Coulomb interactions, the van der Waals interactions and so on. It can also be used to accelerate calculations of the Biot-Savart integral. The diocotron modes reproduced by the simulations agree with the result predicted by linear theory. This indicates that the current-vortex method is applicable to problems of the non-neutral plasma. The linear growth rates of the diocotron instability in the simulations also agree with the theoretical ones. This implies that MDGRAPE-2 gives the sufficiently accurate results for the calculations of the current-vortex method. A mechanism of merging of electron clumps is demonstrated by the simulations. It is concluded that the electric field induced by the conducting wall makes the nonlinear stage unstable and causes the clumps to merge

  16. Test results of NREL 10M, special-purpose family of thin airfoils

    Starcher, K.L.; Nelson, V.C.; Wei, Jun [West Texas A& M Univ., Canyon, TX (United States)

    1996-12-31

    Two 25 kW Carter Wind Systems were tested to determine performance differences between production blades and rotors with NREL Special Purpose Thin Airfoils. Blade design, mold preparation, blade production, and testing were conducted. Design tools were created for computer modeling of the blade. The blades had the same twist, taper, and length as production blades. Flap natural frequency was adjusted to be as similar as possible between rotors, as was blade mass, blade center of gravity and rotor moment of inertia. Data collected were; wind speed at hub height, blade root flap & edgewise loads, main shaft torque, azimuth position, teeter angle, yaw angle and electrical power. These data were collected at 128 Hertz for data sets of eight seconds. This data set was then written to hard disk and the cycle repeated resulting in a file containing five and one half minutes of data. A data run consisted of; preflight checkout/warm-up of equipment, preflight calibration/verification of all sensors on both turbines, collection of five files of data (about thirty minutes of data), post flight calibration/verification of sensors. During this high speed data collection period there were a total of twenty-four data runs collected. Data were collected for wind speeds in the range about 7, 10 and 13 m/s. A data matrix was filled for clean, medium and heavy surface roughness. Baseline power curves, parametric pitch variation runs to establish testing pitch settings, high speed data collection runs with and without applied surface roughness were completed and analyzed. Data were compared using simple arithmetic mean, Fast Fourier Transform (FFT) analysis, rainflow counting algorithms and wavelet analysis. The NREL airfoils showed much less sensitivity to surface roughness. There were minimal root bending load differences. Annual energy production during long term operation is being determined. 9 refs., 7 figs.

  17. Experiences from the exercise ''MERLIN'' for the detection of radioactive substances with the participation of special-purpose vehicles

    Griesbach, M.

    2009-01-01

    Experiences of an exercise with hazardous goods, in particular with radioactive substances (measurements and taking environmental samples) are described. Several special-purpose vehicles with equipment and specially trained crews were used together with radiation protection experts according to the concept of Hesse. It has been the greatest exercise in Hesse with regard to hazardous goods and in particular with regard to ''incidents with radioactive substances''. (orig.)

  18. Preliminary Assessment of Two Alternative Core Design Concepts for the Special Purpose Reactor

    Sterbentz, James W. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Werner, James E. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Hummel, Andrew J. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Kennedy, John C. [Idaho National Lab. (INL), Idaho Falls, ID (United States); O' Brien, Robert C. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Dion, Axel M. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Wright, Richard N. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Ananth, Krishnan P. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2017-11-01

    The Special Purpose Reactor (SPR) is a small 5 MWt, heat pipe-cooled, fast reactor based on the Los Alamos National Laboratory (LANL) Mega-Power concept. The LANL concept features a stainless steel monolithic core structure with drilled channels for UO2 pellet stacks and evaporator sections of the heat pipes. Two alternative active core designs are presented here that replace the monolithic core structure with simpler and easier to manufacture fuel elements. The two new core designs are simply referred to as Design A and Design B. In addition to ease of manufacturability, the fuel elements for both Design A and Design B can be individually fabricated, assembled, inspected, tested, and qualified prior to their installation into the reactor core leading to greater reactor system reliability and safety. Design A fuel elements will require the development of a new hexagonally-shaped UO2 fuel pellet. The Design A configuration will consist of an array of hexagonally-shaped fuel elements with each fuel element having a central heat pipe. This hexagonal fuel element configuration results in four radial gaps or thermal resistances per element. Neither the fuel element development, nor the radial gap issue are deemed to be serious and should not impact an aggressive reactor deployment schedule. Design B uses embedded arrays of heat pipes and fuel pins in a double-wall tank filled with liquid metal sodium. Sodium is used to thermally bond the heat pipes to the fuel pins, but its usage may create reactor transportation and regulatory challenges. An independent panel of U.S. manufacturing experts has preliminarily assessed the three SPR core designs and views Design A as simplest to manufacture. Herein are the results of a preliminary neutronic, thermal, mechanical, material, and manufacturing assessment of both Design A and Design B along with comparisons to the LANL concept (monolithic core structure). Despite the active core differences, all three reactor concepts behave

  19. The Myth - Food Truck

    Otálora Salgado, Esteban

    2015-01-01

    Food truck de comida típica colombiana fusión que espera solucionar la percepción que se tiene acerca de la comida callejera. Para ello, se ha realizado un estudio donde se identifica el problema y se plantea como solución la creación de un food truck que cumpla con todos los estándares de calidad y a su vez innove.

  20. UTV Expansion Pack - Special-Purpose Rank Revealing Algorithms (version 1.0 for Matlab 6.5)

    Fierro, Ricardo D.; Hansen, Per Christian

    This collection of Matlab software supplements and complements the package UTV Tools from 1999, and includes implementations of special-purpose rank-revealing algorithms developed since the publication of the original package. We provide algorithms for computing and modifying symmetric rank...

  1. Design of special purpose products made of nanomodified collagen-containing materials with radio-frequency discharge

    Makhotkina, L. Yu; Sharifullin, S. N.

    2016-06-01

    Research results shows that RF-plasma treatment increases the adhesion of the coating film to the leather uppers and resistance to abrasion and repeated bending of uppers, which define the ability of material to preserve its consumer properties and characterize longer safety of special purpose footwear form during its wearing.

  2. Establishment of the foundation for international collaborating research with US NASA FTCSC to develop space, military and special purpose food

    Jo, Chul Hun; Byun, Myung Woo; Lee, Ju Wun; Kim, Dong Ho; Kim, Kyung Pho; Kim, Jang Ho; Kwon, Jung Ho

    2005-08-01

    In the space era of 21st century, the advancement of aerospace field is essential for ensuring the national security and raising the national status. Internationally spacefood and space life support system is considered as an limitedly developed technology area. Establishment of the foundation for collaborating study with NASA FTCSC to develop space, military, and special food. Acquirement of the basis of the technology development for safe, long-term preservation of military and special purpose food to ensure national security as well as health and welfare

  3. Dynamics of dump truck entrance onto the hoist platform of a mine inclined elevator

    Nosyrev, B.A.; Popov, Yu.V.; Mukhutdinov, Sh.D. (Sverdlovskii Gornyi Institut (USSR))

    1989-01-01

    Analyzes the feasibility of transporting heavy-duty dump trucks along slopes on special platforms in coal surface mines. The platforms are hoisted by winches. Theoretical problems associated with hoisting a loaded platform upwards are analyzed. Problems associated with truck travel in the platform area, its exact positioning and mechanical vibrations of the platform caused by truck movement are discussed. Vibrations of the platform with a loaded truck and vibration amplitudes are analyzed. Five states of the system are evaluated. Methods for prevention of excessive vibrations by optimization of platform design and use of flexible elements are evaluated. Optimum speed of truck movement for platform entering is recommended.

  4. Some questions of using the algebraic coding theory for construction of special-purpose processors in high energy physics spectrometers

    Nikityuk, N.M.

    1989-01-01

    The results of investigations of using the algebraic coding theory for the creation of parallel encoders, majority coincidence schemes and coordinate processors for the first and second trigger levels are described. Concrete examples of calculation and structure of special-purpose processor using the table arithmetic method are given for multiplicity t ≤ 5. The question of using parallel and sequential syndrome coding methods for the registration of events with clusters is discussed. 30 refs.; 10 figs

  5. Benchmarks of programming languages for special purposes in the space station

    Knoebel, Arthur

    1986-01-01

    Although Ada is likely to be chosen as the principal programming language for the Space Station, certain needs, such as expert systems and robotics, may be better developed in special languages. The languages, LISP and Prolog, are studied and some benchmarks derived. The mathematical foundations for these languages are reviewed. Likely areas of the space station are sought out where automation and robotics might be applicable. Benchmarks are designed which are functional, mathematical, relational, and expert in nature. The coding will depend on the particular versions of the languages which become available for testing.

  6. International standard on auditing 800 the auditor`s report on special purpose audit engagements

    Jovanova, Blagica

    2011-01-01

    The purpose of this report is to show the main characteristics of the international standard on auditing 800. ISA 800 explains requirements by making a report on financial statements prepared in accordance with another comprehensive basis of accounting, on a component of financial statements, on compliance with contractual agreements or reports on summarized financial statements.

  7. Truckstop - and Truck - Electrification

    Skip Yeakel

    2001-01-01

    The conclusions of this paper are: 0.5-1.5 G/H and/or BUSG/Y-how much time and money will it take to quantify and WHY BOTHER TO DO SO? No shortage of things to do re truckstop-+ truck - electrification; Better that government and industry should put many eggs in lots of baskets vs. all in one or few; Best concepts will surface as most viable; Economic appeal better than regulation or brute force; Launch Ground Freight Partnership and give it a chance to work; Demonstration is an effective means to educate, and learn from, customers-learning is a two way street; Research, Development, Demonstration, and Deployment (RD 3) are all important but only deployment gets results; TSE can start small in numbers of spaces to accommodate economically inspired growth but upfront plans should be made for expansion if meaningful idle reduction is to follow via TE; 110VAC 15A service/ parking space is minimal-if infrastructure starts like this, upfront plans must be made to increase capacity; Increased electrification of truckstop and truck alike will result in much better life on the road; Improved sleep will improve driver alertness and safety; Reduced idling will significantly reduce fuel use and emissions; Universal appeal for DOD, DOE, DOT, EPA, OEMs, and users alike; Clean coal, gas, hydro, nuclear, or wind energy sources are all distinctly American means by which to generate electricity; Nothing can compete with diesel fuel to serve mobile truck needs; stationary trucks are like power plants-they don't move and should NOT be powered by petroleum products whenever possible; Use American fueled power plants-electricity-to serve truck idling needs wherever practical to do so; encourage economic aspect; Create and reward industry initiatives to reduce fuel use; Eliminate FET on new trucks, provide tax credits (non highway fuel use and investment), provide incentives based on results; Encourage newer/ cleaner truck use; solicit BAAs with mandatory OEM/ fleet participation/ lead

  8. Specialized Monte Carlo codes versus general-purpose Monte Carlo codes

    Moskvin, Vadim; DesRosiers, Colleen; Papiez, Lech; Lu, Xiaoyi

    2002-01-01

    The possibilities of Monte Carlo modeling for dose calculations and optimization treatment are quite limited in radiation oncology applications. The main reason is that the Monte Carlo technique for dose calculations is time consuming while treatment planning may require hundreds of possible cases of dose simulations to be evaluated for dose optimization. The second reason is that general-purpose codes widely used in practice, require an experienced user to customize them for calculations. This paper discusses the concept of Monte Carlo code design that can avoid the main problems that are preventing wide spread use of this simulation technique in medical physics. (authors)

  9. [The Purpose of Medical Education: Proposal to Standardize a System of Credits for Medical Specializations Programs].

    Cañar, Carlos Andrés Pineda

    2012-01-01

    This article analyzes the concept of an academic credit system and proposes a way to systematize medical specialization programs. The credit system is a way to recognize and standardize the total time that a student must devote to their training. Thus, a credit equal to a certain number of hours of classroom training and independent activities is proposed. An educational program is expressed in the number of credits needed for the whole training process to achieve the competencies expected. A review of the concept of competition in education is also performed. The introduction of the term and its relation to the need to measure performance in future professionals according to labor market needs is identified. A critical discussion about skills defining the different types of skills in the educational field is later discussed. Subsequently, the Colombian regulatory framework is presented concerning the powers, in particular, Decree 1295 of 2010, which defines one academic credit equal to 48 hours in a semester, of which 16 hours are classroom and 32 hours are independent study. A tor of the major milestones in the history of medical education is later made. The structure of credits and contact hours, independent of postgraduate psychiatry in the country is reviewed showing the heterogeneity in their approach. The proposal is presented, defining the types of classroom activities and how to calculate the hours of independent study by type of classroom activity. Copyright © 2012 Asociación Colombiana de Psiquiatría. Publicado por Elsevier España. All rights reserved.

  10. Chemical decontamination for decommissioning purposes. (Vigorous decontamination tests of steel samples in a special test loop)

    Bregani, F.; Pascali, R.; Rizzi, R.

    1984-01-01

    The aim of the research activities described was to develop vigorous decontamination techniques for decommissioning purposes, taking into account the cost of treatment of the radwaste, to achieve possibly unrestricted release of the treated components, and to obtain know-how for in situ hard decontamination. The decontamination procedures for strong decontamination have been optimized in static and dynamic tests (DECO-loop). The best values have been found for: (i) hydrochloric acid: 4 to 5% vol. at low temperature, 0.7 to 1% vol. at high temperature (80 0 C); (ii) hydrofluoric plus nitric acid: 1.5% vol. HF + 5% vol. HNO 3 at low temperature; 0.3 to 0.5% vol. HF + 2.5 to 5% vol. HNO 3 at high temperature. High flow rates are not necessary, but a good re-circulation of the solution is needed. The final contamination levels, after total oxide removal, are in accordance with limits indicated for unrestricted release of materials in some countries. The arising of the secondary waste is estimated. Decontamination of a 10 m 2 surface would typically produce 0.5 to 3.0 kg of dry waste, corresponding to 1.6 to 10 kg of concrete conditioned waste

  11. ANFO truck burn trials

    Rosen von, B.; Contestabile, E. [Natural Resources Canada, CANMET Canadian Explosives Research Laboratory, Ottawa, ON (Canada)

    2003-10-01

    This report describes the investigation of a tractor-trailer explosion. A truck loaded with 18,000 kg of commercial explosives, of which 13,000 kg was ammonium nitrate with fuel oil (ANFO), caught fire when it struck a rockcut near Walden, Ontario on August 5, 1998. The fire resulted in the detonation of the load. The Canadian Explosives Research Laboratory (CERL) conducted a test program to examine the suitability of existing explosive transportation regulations. Unconfined burns of ANFO were performed. The accident was recreated in two burn trials in an attempt to identify the mechanism that led from fire to detonation. Two full-scale tests were conducted using complete tractor-trailers, each in a jack-knifed position with most of the explosives placed on the ground in front of the trailer. ANFO was used in the first test to determine its response to thermal stimulus and the likelihood of detonation or explosion. The second test involved ANFO, a slurry and an emulsion. Thermocouples and video cameras were used to observe the burning characteristics of the explosives, the truck and its components. The explosives burned steadily for 80 minutes in each test. Many truck components, such as tires, spring brake chambers and the fuel tank ruptured violently due to the heat. Although no detonation occurred in the test trials, it was concluded that under favourable conditions, many truck components, might produce fragments with enough energy to initiate heat-sensitized explosives. It was suggested that a fragment impact caused the detonation at Walden. 4 refs., 7 tabs., 8 figs.

  12. Truck Drivers' Use of the Internet: A Mobile Health Lifeline.

    Heaton, Karen; Combs, Bryan; Griffin, Russell

    2017-06-01

    Because of their social isolation, irregular and unpredictable schedules, limited access to health care, and long periods of travel, long-haul truckers may benefit from the use of mobile health applications on Internet-capable devices. The purpose of this study was to determine Internet access and usage among a sample of long-haul truck drivers. In this cross-sectional study, truck drivers completed a pencil and paper survey with questions on demographics, work and health histories, and Internet access and usage for both personal and job reasons. A total of 106 truck drivers were recruited from trucking industry trade shows, by word of mouth, and directly from trucking companies. Overall, the truck drivers' use of the Internet was limited. Their usage for personal and job-related reasons differed. Social connectivity and access to health and wellness information were important during personal usage time. Job-related Internet use was highly practical, and applied to seeking information for directions and maps, fuel stops and pricing, and communicating with employers or transmitting documents. Age and experience were associated with Internet use. Younger, less-experienced drivers used the Internet more than older, experienced drivers. Targeted mobile health messaging may be a useful tool to inform truck drivers of health conditions and plans, and may provide links to primary care providers needing to monitor or notify drivers of diagnostic results or treatment plans.

  13. Adaptation of topology optimization on truck-structure; Kinshitsukaho ni yoru iso saitekika shuho no truck kozo eno tekiyo

    Tachibana, H; Kojima, A; Chiba, S [Mitsubishi Motors Corp., Tokyo (Japan)

    1997-10-01

    An optimization using the homogenization method has been applied to a truck-structure on the concept design stage. A truck-structure is grouped into 3 classes (thin plate structure , thick plate structure and solid structure), then example, effectiveness and method for the application for the purpose of weight reduction , high rigidity and high eigen-frequency are introduced. 3 refs., 24 figs., 1 tab.

  14. Special Purpose Systems

    2017-01-30

    Sign-off Memorandum to the NWEC Consortium Management Firm. The Sign-off Memorandum will be used to verify that all submissions are technically...the Windstream Task 366. 08/01/2016 Purchased ½” Drive Impact drill and socket sets from Amazon in support of the Windstream Task 366. 08/01...for a MakerBot from MakerBot in Support of Task MJU. 01/12/2017 Purchased Network Switch from BlackBox in support of the 366 Tasking. 10

  15. Evaluation for special purposes

    Viorica Toma

    2011-01-01

    This article aims to present the principles of international accounting standards and regulations on how Romanian accepted recognition of assets in financial reports.Company's financial reports include financial statements and other statements / reports of the directors.At the same time, it will insist on base / type of value that can be used by evaluators to harmonize concepts and especially the bases of valuation for balance sheet recognition of assets.Currently identity is observed near or...

  16. Vehicle to vehicle communications for trucks.

    2014-01-01

    The trucking industry is a critical component of American commerce. The American : Trucking Association estimates that over 80 percent of U.S. communities depend : exclusively on trucking for delivery of their goods and commodities

  17. Special purpose materials: an assessment of needs and the role of these materials in the national program

    Gold, R.E.; Clinard, F.W. Jr.; Davis, J.W.

    1978-01-01

    The scope of activities of the Task Group on Special Purpose Materials includes those materials requirements not specifically addressed by the other OFE materials task groups. These materials can be organized according to seven broad materials applications or functions which appear to be generic to all magnetically confined fusion reactor concepts. These are breeding materials, coolants, materials for tritium service, graphite and silicon carbide, electrical insulators and ceramics, heat-sink materials, and magnet materials. The present paper describes the importance of each of these areas of materials technology, outlines major problems or areas of uncertainty, and reviews past and current contributions to our state of understanding as it may relate to fusion power applications

  18. Conceptual design studies of special-purpose equipment for Fusion Engineering Device torus-sector remote maintenance

    Masson, L.S.; Watts, K.D.; Aldrich, W.E.; McPherson, R.S.

    1982-01-01

    One of the major maintenance operations anticipated for fusion reactors of the Tokamak configuration is remote removal and replacement of torus sectors. This operation will be difficult due to the massive nature of the sector (375 tonnes), and also due to the precision with which it must be positioned within the fixed structure. The same problem, only to a lesser degree, applies to sub-components of the sector such as the limiter blades, shielding, test assemblies, etc. General and specific design requirements have been generated and trade studies conducted on reactor interfacing details as well as handling machine concepts. On the basis of the design requirements and trade studies, a perferred concept for the sector handling machine was developed. In addition, a similar machine was developed for handling the intermediate sized sector sub-components. While most operations will be performed by special purpose machines such as described above, there is a need for a versatile, relatively high capacity mobile system. A concept suitable for this mobile application was also developed as part of these studies. The general conclusion, to the extent these studies have been completed, was that special single-purpose machines will be required to perform the operations requiring high load capacity and handling precision. The machine concepts developed were felt to be within the state-of-the-art, and will make extensive use of commercially available components. The most serious problem was felt to be development of simple methods to obtain the required precision in positioning massive objects such as the torus sector

  19. Mitigating Wind Induced Truck Crashes

    2009-12-25

    Dangerous weather and high wind in particular, is a common contributing factor in truck crashes. High wind speeds have been documented as a perennial cause of truck crashes in Kansas and other Great Plains states. The possibility of reducing such cra...

  20. Development of the New Light-Duty Hybrid Truck

    Yamaguchi, Koichi

    2008-01-01

    Hino Motors, Ltd., developed the new light-duty hybrid truck whose traction motor, inverter, and traction battery were completely redesigned for maximizing output and efficiency. It also succeeds in balancing low fuel economy and low exhaust emissions by utilizing a combination of a new hybrid system control with a specially developed diesel engine.

  1. Truck shovel users group

    Thomas, J. [Surface Mining Association for Research and Technology, AB (Canada)

    2008-07-01

    The Truck Shovel Users Group (TSUG) was developed as part of the Surface Mining Association for Research and Technology (SMART), an association of companies that meet to coordinate technology developments for the mining industry. The TSUG meet regularly to discuss equipment upgrades, maintenance planning systems, and repair techniques. The group strives to maximize the value of its assets through increased safety, equipment performance and productivity. This presentation provided administrative details about the TSUG including contact details and admission costs. It was concluded that members of the group must be employed by companies that use heavy mining equipment, and must also be willing to host meetings, make presentations, and support the common goals of the group. tabs., figs.

  2. 49 CFR 399.207 - Truck and truck-tractor access requirements.

    2010-10-01

    .... Exception. If air and electrical connections necessary to couple or uncouple a truck-tractor from a trailer... 49 Transportation 5 2010-10-01 2010-10-01 false Truck and truck-tractor access requirements. 399... Vehicles § 399.207 Truck and truck-tractor access requirements. (a) General rule. Any person entering or...

  3. Health promotion in the trucking setting: Understanding Dutch truck drivers' road to healthy lifestyle changes.

    Boeijinga, Anniek; Hoeken, Hans; Sanders, José

    2016-10-17

    The working environment, the nature of the work, and the characteristics of truck drivers as a social group typically pose great challenges for the truck drivers' health and health promotion activities aiming to improve it. The purpose was to obtain a better understanding of (a) Dutch truck drivers' perceptions of health and lifestyle themes, and (b) the challenges they experience in their pursuit of a more healthy lifestyle, as a guiding framework for the development of health interventions targeting this occupational group. In this qualitative study, we conducted and analyzed 20 semi-structured interviews and seven cases of participant observations with Dutch truck drivers. Grounded theory was used to analyze the data. Our findings illustrate that Dutch truck drivers wish to improve their lifestyle but have unproductive associations with concepts of healthy living as well as a tendency to downplay their health risks. In addition, they experience barriers within their work and personal environment that prevent them from translating their intentions into actual lifestyle changes. Based on the insights derived from the interviews, we discuss recommendations for the development of more effective health promotion interventions for truck drivers.

  4. DESIGN OF EXPERIMENTS IN TRUCK COMPANY

    Bibiana Kaselyova

    2015-07-01

    Full Text Available Purpose: Design of experiment (DOE represent very powerful tool for process improvement vastly supported by six sigma methodology. This approach is mostly used by large and manufacturing orientated companies. Presented research is focused on use of DOE in truck company, which is medium size and service orientated. Such study has several purposes. Firstly, detailed description of improvement effort based on DOE can be used as a methodological framework for companies similar to researched one. Secondly, it provides example of successfully implemented low cost design of experiment practise. Moreover, performed experiment identifies key factors, which influence the lifetime of truck tyres.Design/methodology: The research in this paper is based on experiment conducted in Slovakian Truck Company. It provides detailed case study of whole improvement effort, together with problem formulation, design creation and analysis, as well as the results interpretation. The company wants to improve lifetime of the truck tyres. Next to fuel consumption, consumption of tyres and their replacement represent according to them, one of most costly processes in company. Improvement effort was made through the use of PDCA cycle. It start with analysis of current state of tyres consumption. The variability of tyres consumption based on years and types was investigated. Then the causes of tyres replacement were identified and screening DOE was conducted. After a screening design, the full factorial design of experiment was used to identify main drivers of tyres deterioration and breakdowns. Based on result of DOE, the corrective action were propose and implement.Findings: Based on performed experiment our research describes process of tyres use and replacement. It defines main reasons for tyre breakdown and identify main drivers which influence truck tyres lifetime. Moreover it formulates corrective action to prolong tyres lifetime.Originality: The study represents full

  5. Implementation of exclusive truck facilities

    Fekpe, E. [Battelle Memorial Inst., Columbus, OH (United States). Transportation Market Sector

    2007-07-01

    This paper discussed the issue of highway congestion, safety, and efficiency in freight movement on highways, with particular reference to the challenge of supporting increasing capacity demand from truck traffic. Innovative and practical solutions are needed to address the growing need for more efficient freight movement while maintaining acceptable levels of safety on highways. The concept of exclusive truck facilities (ETFs) is becoming an attractive option as a feasible strategy to help stabilize traffic flow, reduce congestion, improve safety, enhance transportation system management, improve access to freight facilities, and improve efficiency in freight movement along corridors of national importance. ETFs can either be truck only lanes or truckways. Passenger cars may not use ETFs. However, the use of ETFs could involve high costs of construction, maintenance, and acquisition of additional right of way. A cost-benefit analysis was performed for alternative ETF configurations under different traffic and site characteristics. A set of criteria was then proposed for identifying suitable locations for exclusive truck lanes. It was proposed that ETFs are economically feasible at locations with traffic volume of 100,000 vehicles per day or more and with a truck volume of at least 25 per cent of the traffic. In addition, the rate of truck-involved fatal crashes and level of service should be used to prioritize preliminary candidate locations that satisfy the traffic criteria. Consideration should also be given to the existence of freight terminals, ports, processing centers or regional distribution centres that are close to highways. 11 refs., 1 tab.

  6. Optimization of a truck-drone in tandem delivery network using K-means and genetic algorithm

    Mourelo Ferrandez, Sergio; Harbison, Timothy; Webwer, Troy; Sturges, Robert; Rich, Robert

    2016-01-01

    Purpose: The purpose of this paper is to investigate the effectiveness of implementing unmanned aerial delivery vehicles in delivery networks. We investigate the notion of the reduced overall delivery time and energy for a truck-drone network by comparing the in-tandem system with a stand-alone delivery effort. The objectives are (1) to investigate the time and energy associated to a truck-drone delivery network compared to standalone truck or drone, (2) to propose an optimizat...

  7. French intensive truck garden

    Edwards, T D

    1983-01-01

    The French Intensive approach to truck gardening has the potential to provide substantially higher yields and lower per acre costs than do conventional farming techniques. It was the intent of this grant to show that there is the potential to accomplish the gains that the French Intensive method has to offer. It is obvious that locally grown food can greatly reduce transportation energy costs but when there is the consideration of higher efficiencies there will also be energy cost reductions due to lower fertilizer and pesticide useage. As with any farming technique, there is a substantial time interval for complete soil recovery after there have been made substantial soil modifications. There were major crop improvements even though there was such a short time since the soil had been greatly disturbed. It was also the intent of this grant to accomplish two other major objectives: first, the garden was managed under organic techniques which meant that there were no chemical fertilizers or synthetic pesticides to be used. Second, the garden was constructed so that a handicapped person in a wheelchair could manage and have a higher degree of self sufficiency with the garden. As an overall result, I would say that the garden has taken the first step of success and each year should become better.

  8. The Treatment of Polysemy and Homonymy in Monolingual General-purpose Dictionaries with Special Reference to Isichazamazwi SesiNdebele

    Eventhough Ndlovu

    2011-10-01

    Full Text Available

    ABSTRACT: This article focuses on the treatment of polysemy and homonymy in general-purpose monolingual dictionaries with special reference to Isichazamazwi SesiNdebele. It was found that there are some inconsistencies in the treatment of polysemous and homonymous entries in this dictionary. The article shows that an overreliance on one criterion, particularly etymology, to distinguish polysemy and homonymy is often misleading and unreliable. Polysemy itself has its own inherent complexities, among these being the problem of determining the exact number of meanings of a polysemous lemma. When the meanings of a polysemous lemma are listed, the central or primary meaning, which is not always easily ascertainable, should come first. A holistic approach is proposed to distinguish polysemy and homonymy, which entails the use of the following criteria: etymology, relatedness vs unrelatedness of meaning, componential analysis, the identification of the central or core meaning and the test of ambiguity. Whatever results are obtained from a particular criterion, these findings must be compared with those of other criteria, and verified against native speakers' intuitive knowledge and introspective judgements.

    OPSOMMING: Die behandeling van polisemie en homonimie in eentalige algemene woordeboeke met spesiale verwysing na Isichazamazwi SesiNdebele. Hierdie artikel fokus op die behandeling van polisemie en homonimie in algemene eentalige woordeboeke met spesiale verwysing na Isichazamazwi SesiNdebele. Daar is vasgestel dat daar 'n aantal inkonsekwensies in die behandeling van poliseme en homonieme inskrywings in hierdie woordeboek is. Die artikel toon dat 'n te groot steun op een kriterium, veral etimologie, om polisemie en homonimie te onderskei, dikwels misleidend en onbetroubaar is. Polisemie self het sy eie inherente gekompliseerdhede waarvan sommige die probleem is om die presiese aantal betekenisse van 'n poliseme lemma te bepaal. Wanneer

  9. Heavy Truck Engine Program

    Nelson, Christopher

    2009-01-08

    The Heavy Duty Truck Engine Program at Cummins embodied three significant development phases. All phases of work strove to demonstrate a high level of diesel engine efficiency in the face of increasingly stringent emission requirements. Concurrently, aftertreatment system development and refinement was pursued in support of these efficiency demonstrations. The program's first phase focused on the demonstration in-vehicle of a high level of heavy duty diesel engine efficiency (45% Brake Thermal Efficiency) at a typical cruise condition while achieving composite emissions results which met the 2004 U.S. EPA legislated standards. With a combination of engine combustion calibration tuning and the development and application of Urea-based SCR and particulate aftertreatment, these demonstrations were successfully performed by Q4 of 2002. The second phase of the program directed efforts towards an in-vehicle demonstration of an engine system capable of meeting 2007 U.S. EPA legislated emissions requirements while achieving 45% Brake Thermal Efficiency at cruise conditions. Through further combustion optimization, the refinement of Cummins Cooled EGR architecture, the application of a high pressure common rail fuel system and the incorporation of optimized engine parasitics, Cummins Inc. successfully demonstrated these deliverables in Q2 of 2004. The program's final phase set a stretch goal of demonstrating 50% Brake Thermal Efficiency from a heavy duty diesel engine system capable of meeting 2010 U.S. EPA legislated emissions requirements. Cummins chose to pursue this goal through further combustion development and refinement of the Cooled EGR system architecture and also applied a Rankine cycle Waste Heat Recovery technique to convert otherwise wasted thermal energy to useful power. The engine and heat recovery system was demonstrated to achieve 50% Brake Thermal Efficiency while operating at a torque peak condition in second quarter, 2006. The 50% efficient

  10. The Text of Tile Master Agreement between the Agency and the United States of America Governing Sales of Source, By- Product and Special Nuclear Materials for research Purposes

    1974-01-01

    The text of the Master Agreement Governing Sales of Source, Bye Product and Special Nuclear Materials for Research Purposes, which has been concluded between the Agency and the Government of the United States of America, is reproduced herein for the information of all Members,

  11. Prueba de Aptitud para el Aprendizaje de Lenguas Extranjeras (PAPALE) Language Aptitude Test (LAT) (First and Second Versions). English for Special Purposes. Emergency Care Attendant.

    Muro, Gertrude

    This book contains two versions of the Language Aptitude Test. It is part of a package of materials developed for use in an English for Special Purposes project, which offers classes in reading, grammar, and emergency care attendant training for limited English proficient students. Introductory material describes the parts of two versions and…

  12. The Development of Strategies for the Assignment of Semantic Information to Unknown Lexemes in Text. Lenguas para Objetivos Especificas (Languages for Special Purposes), No. 5.

    Alderson, Charles; Alvarez, Guadalupe

    An English for Special Purposes (ESP) course being developed aims to give the students a series of techniques to help them handle vocabulary in a text, and teach them strategies for identifying meaning in context. Traditional strategies, such as the study of morphology, use of grammatical information, and exercises in dictionary usage, are…

  13. Acceptance test report for core sample trucks 3 and 4

    Corbett, J.E.

    1996-01-01

    The purpose of this Acceptance Test Report is to provide documentation for the acceptance testing of the rotary mode core sample trucks 3 and 4, designated as HO-68K-4600 and HO-68K-4647, respectively. This report conforms to the guidelines established in WHC-IP-1026, ''Engineering Practice Guidelines,'' Appendix M, ''Acceptance Test Procedures and Reports.'' Rotary mode core sample trucks 3 and 4 were based upon the design of the second core sample truck (HO-68K-4345) which was constructed to implement rotary mode sampling of the waste tanks at Hanford. Successful completion of acceptance testing on June 30, 1995 verified that all design requirements were met. This report is divided into four sections, beginning with general information. Acceptance testing was performed on trucks 3 and 4 during the months of March through June, 1995. All testing was performed at the ''Rock Slinger'' test site in the 200 West area. The sequence of testing was determined by equipment availability, and the initial revision of the Acceptance Test Procedure (ATP) was used for both trucks. Testing was directed by ICF-KH, with the support of WHC Characterization Equipment Engineering and Characterization Project Operations. Testing was completed per the ATP without discrepancies or deviations, except as noted

  14. Large truck and bus crash facts, 2010.

    2012-09-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2010. Selected crash statistics on passenger : vehicles are also presen...

  15. Large truck and bus crash facts, 2012.

    2014-06-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and property damage only crashes involving large trucks and buses in 2012. Selected crash statistics on passenger vehicles are also presented ...

  16. Large truck and bus crash facts, 2013.

    2015-04-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and property damage only crashes involving large trucks and buses in 2013. Selected crash statistics on passenger vehicles are also presented ...

  17. Large truck and bus crash facts, 2009.

    2011-10-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2009. Selected crash statistics on passenger : vehicles are also presen...

  18. Large truck and bus crash facts, 2011.

    2013-10-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2011. Selected crash statistics on passenger : vehicles are also presen...

  19. Naturalistic Study of Truck Following Behavior

    2016-04-01

    Volpe conducted the Naturalistic study of truck following behavior to gain a better understanding of how trucks follow other vehicles in the real world, with the ultimate goal of supporting the Federal Highway Administration in the development of aut...

  20. Commercial truck parking and other safety issues.

    2015-10-01

    Commercial truck parking is a safety issue, since trucks are involved in approximately 10% of all fatal accidents on interstates and : parkways in Kentucky. Drivers experience schedule demands and long hours on the road, yet they cannot easily determ...

  1. Norcal Prototype LNG Truck Fleet: Final Results

    2004-07-01

    U.S. DOE and National Renewable Energy Laboratory evaluated Norcal Waste Systems liquefied natural gas (LNG) waste transfer trucks. Trucks had prototype Cummins Westport ISXG engines. Report gives final evaluation results.

  2. Papers on vehicle size : cars and trucks

    1988-06-01

    The four papers in this volume describe analyses of car size : trends and truck occupant injuries and fatalities. All four were : written between June 1985 and December 1987. The topics : addressed include where heavy truck accidents occur, injury an...

  3. Trucks involved in fatal accidents factbook 2008.

    2011-03-01

    This document presents aggregate statistics on trucks involved in traffic accidents in 2008. The : statistics are derived from the Trucks Involved in Fatal Accidents (TIFA) file, compiled by the : University of Michigan Transportation Research Instit...

  4. Trucks involved in fatal accidents factbook 2007.

    2010-01-01

    This document presents aggregate statistics on trucks involved in traffic accidents in 2007. The : statistics are derived from the Trucks Involved in Fatal Accidents (TIFA) file, compiled by the : University of Michigan Transportation Research Instit...

  5. Development of Diesel Engine Operated Forklift Truck for Explosive Gas Atmospheres

    Vishwakarma, Rajendra Kumar; Singh, Arvind Kumar; Ahirwal, Bhagirath; Sinha, Amalendu

    2018-02-01

    For the present study, a prototype diesel engine operated Forklift truck of 2 t capacity is developed for explosive gas atmosphere. The parts of the Forklift truck are assessed against risk of ignition of the explosive gases, vapors or mist grouped in Gr. IIA and having ignition temperature more than 200°C. Identification of possible sources of ignition and their control or prevention is the main objective of this work. The design transformation of a standard Forklift truck into a special Forklift truck is made on prototype basis. The safety parameters of the improved Forklift truck are discussed in this paper. The specially designed Forklift truck is useful in industries where explosive atmospheres may present during normal working conditions and risk of explosion is a concern during handling or transportation of materials. This indigenous diesel engine based Forklift truck for explosive gas atmosphere classified as Zone 1 and Zone 2 area and gas group IIA is developed first time in India in association with the Industry.

  6. Aerodynamics Research Revolutionizes Truck Design

    2008-01-01

    During the 1970s and 1980s, researchers at Dryden Flight Research Center conducted numerous tests to refine the shape of trucks to reduce aerodynamic drag and improved efficiency. During the 1980s and 1990s, a team based at Langley Research Center explored controlling drag and the flow of air around a moving body. Aeroserve Technologies Ltd., of Ottawa, Canada, with its subsidiary, Airtab LLC, in Loveland, Colorado, applied the research from Dryden and Langley to the development of the Airtab vortex generator. Airtabs create two counter-rotating vortices to reduce wind resistance and aerodynamic drag of trucks, trailers, recreational vehicles, and many other vehicles.

  7. 41 CFR 102-73.180 - What types of special purpose space may the Department of Defense lease?

    2010-07-01

    ... Property Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false What types of special... City, NY. (h) Recreation centers. (i) Reserve training space. (j) Service clubs. (k) Testing...

  8. Multistage Mechanical Transmissions with Automatic Control for Advanced Trucks and Buses

    Blokhin Aleksandr

    2017-12-01

    Full Text Available The study considers the basic trends of development of modern mechanical transmissions of trucks and buses. It provides the developed various series of multispeed transmissions with automatic control and a number of transmissions from 6 to 16 for trucks and buses. The paper shows the basic parameters of the standard series of new transmissions received on the basis of innovative technical solutions. It provides the results of experimental studies of 16-speed transmissions on a special test stand and on the road as part of a truck transmission. Theoretical and experimental data on the gear change time are compared.

  9. Fuel Cell Hydroge Manifold for Lift Trucks

    Hosseinzadeh, Elham

    . Battery driven lift trucks are being used more and more in different companies to reduce their emissions. However, battery driven lift trucks need long time to recharge and may be out of work for a long time. Fuel cell driven lift trucks diminish this problem and are therefore getting more attention...

  10. Weather delay costs to trucking.

    2012-11-01

    Estimates of the nations freight sector of transportation range to upwards of $600 billion of total gross domestic product with 70 percent of total value and 60 percent of total weight moving by truck. Weather-related delays can add significantly ...

  11. Truck Thermoacoustic Generator and Chiller

    Keolian, Robert

    2011-03-31

    This Final Report describes the accomplishments of the US Department of Energy (DOE) cooperative agreement project DE-FC26-04NT42113 - Truck Thermoacoustic Generator and Chiller - whose goal is to design, fabricate and test a thermoacoustic piezoelectric generator and chiller system for use on over-the-road heavy-duty-diesel trucks, driven alternatively by the waste heat of the main diesel engine exhaust or by a burner integrated into the thermoacoustic system. The thermoacoustic system would utilize engine exhaust waste heat to generate electricity and cab air conditioning, and would also function as an auxiliary power unit (APU) for idle reduction. The unit was to be tested in Volvo engine performance and endurance test cells and then integrated onto a Class 8 over-the-road heavy-duty-diesel truck for further testing on the road. The project has been a collaboration of The Pennsylvania State University Applied Research Laboratory, Los Alamos National Laboratory, Clean Power Resources Inc., and Volvo Powertrain (Mack Trucks Inc.). Cost share funding was provided by Applied Research Laboratory, and by Clean Power Resources Inc via its grant from Innovation Works - funding that was derived from the Commonwealth of Pennsylvania. Los Alamos received its funding separately through DOE Field Work Proposal 04EE09.

  12. A tough truck for ATLAS

    2003-01-01

    One of the mobile support structures that will be used to manoeuvre and assemble components of the ATLAS detector in its cavern was put through its paces at the end of July and passed its load tests with flying colours. The tests, which involved the surveyors taking measurements to detect any load-induced mechanical deformations, were carried out in Building 191. "The "truck" has been subjected to static tests with loads of up to 1250 tonnes and can carry and transport on air cushions a nominal load of up to 1000 tonnes at a top speed of 30 cm per minute," explains project leader Tommi Nyman. "It took two weeks to assemble the truck's components, the last of which arrived at CERN on 24 June. It then took a further 20 days to load the truck up for the test." The 8.5 metre-high truck will be used for final assembly of some of the ATLAS components, including the calorimeters, in cavern UX15. This powerful device is the result of a collaboration between CERN and the Henryk Niewodniczanski Institute of Nuclear ...

  13. Analysis of major trends in U.S. commercial trucking, 1977-2002.

    Bertram, K. M.; Santini, D .J.; Vyas, A. D.

    2009-06-10

    This report focuses on various major long-range (1977-2002) and intermediate-range (1982-2002) U.S. commercial trucking trends. The primary sources of data for this period were the U.S. Bureau of the Census Vehicle Inventory and Use Survey and Truck Inventory and Use Survey. In addition, selected 1977-2002 data from the U.S. Department of Energy/Energy Information Administration and from the U.S. Department of Transportation/Federal Highway Administration's Highway Statistics were used. The report analyzes (1) overall gasoline and diesel fuel consumption patterns by passenger vehicles and trucks and (2) the population changes and fuels used by all commercial truck classes by selected truck type (single unit or combination), during specified time periods, with cargo-hauling commercial trucks given special emphasis. It also assesses trends in selected vehicle miles traveled, gallons per vehicle miles traveled, and gallons per cargo ton-mile traveled, as well as the effect of cargo tons per truck on fuel consumption. In addition, the report examines long-range trends for related factors (e.g., long-haul mileages driven by heavy trucks) and their impacts on reducing fuel consumption per cargo-ton-mile and the relative shares of total commercial fuel use among truck classes. It identifies the effects of these trends on U.S. petroleum consumption. The report also discusses basic engineering design and performance, national legislation on interstate highway construction, national demographic trends (e.g., suburbanization), and changes in U.S. corporate operations requirements, and it highlights their impacts on both the long-distance hauling and shorter-distance urban and suburban delivery markets of the commercial trucking industry.

  14. 14 CFR 63.23 - Special purpose flight engineer and flight navigator certificates: Operation of U.S.-registered...

    2010-01-01

    ... purpose flight engineer and flight navigator certificates: Operation of U.S.-registered civil airplanes... flight engineer or flight navigator duties on a civil airplane of U.S. registry, leased to a person not a... certificate holder is performing flight engineer or flight navigator duties on the U.S.-registered civil...

  15. Quality-assurance study of the special-purpose finite-element program SPECTROM: II. Plasticity problems

    Callahan, G.D.; Fossum, A.F.

    1982-11-01

    General plasticity theory and solution techniques as are currently employed in RE/SPEC's finite element plasticity code SPECTROM-II are presented. Various yield functions are discussed and their differences are illustrated using example problems. Comparison of the results of SPECTROM-II with analytical solutions, numerical solutions, and the general purpose finite element program MARC-CDC show excellent agreement

  16. Utilization of Social Media Platforms for Educational Purposes among the Faculty of Higher Education with Special Reference to Tamil Nadu

    Vivakaran, Mangala Vadivu; Neelamalar, M.

    2018-01-01

    Social media tools are observed to play a vital role in the renovation of the conventional teaching and learning practices across the globe. Though primarily developed for online social communication, social media platforms tend to possess suitable tools that can be used for instructional purposes in order to initiate active learning among…

  17. Quality-assurance study of the special - purpose finite-element program - SPECTROM: I. Thermal, thermoelastic, and viscoelastic problems

    Wagner, R.A.

    1980-12-01

    This comparison study involves a preliminary verification of finite element calculations. The methodology of the comparison study consists of solving four example problems with both the SPECTROM finite element program and the MARC-CDC general purpose finite element program. The results show close agreement for all example problems

  18. Computations for Truck Sliding with TRUCK 3.1 Code

    1989-08-01

    16 REFERENCES 1. L u. \\Villiam N.. Hobbs. Norman P. and Atkinson, Michael. TRUCK 3.1-An Improrcd Digital (’oiputtr Program for Calculating the Response...for Operations and Plans ATIN: Technical Libary Director of Chemical & Nuear Operations Dpartnt of the AIW Waskbington, DC 20310 1 Cocaeder US Ay...Lawrenoe Livermore Lab. ATIN: Code 2124, Tedhnical ATTN: Tech Info Dept L-3 Reports Libary P.O. Be 808 Monterey, CA 93940 Livermore, CA 94550 AFSC

  19. Powershift transmission for dump trucks; Neues Lastschaltgetriebe fuer Dump Trucks

    Rebholz, Wolfgang; Geis, Joerg; Riedhammer, Michael [ZF Friedrichshafen AG, Friedrichshafen (Germany)

    2012-04-15

    Articulated dumpers (also called dump trucks) are used in many locations where large quantities of earth, spoil, gravel or other materials have to be moved on construction sites or in quarries. ZF has developed a new transmission with eight forward and four reverse gears up to production standard specifically for use in these vehicles. The integrated primary retarder is continuously controllable and provides maximum braking torque of up to 1800 Nm. (orig.)

  20. A decade of cost-reduction in very large telescopes - The SST as prototype of special-purpose telescopes

    Smith, Harlan J.

    1989-10-01

    Many design and technical innovations over the past ten or fifteen years have reduced the costs of very large telescopes by nearly an order of magnitude over those of classical designs. Still a further order of magnitude reduction is possible if the telescope is specialized for on-axis spectroscopy, giving up especially the luxuries of wide field, multiple focal positions, and access to all the sky at will. The SST (Spectroscopic Survey Telescope) will use eighty-five 1-m circular mirrors mounted in a steel frame composed of hundreds of interlocking tetrahedrons, keeping a fixed elevation angle of 60 deg with rotation only in azimuth. Using an optical fiber it will feed as much light to spectrographs as can be done by a conventional 8-m telescope, yet has a target basic completion cost of only $6 million.

  1. Truck transportation of radioactive materials

    Madsen, M.M.; Wilmot, E.L.

    1983-01-01

    Analytical models in RADTRAN II are used to calculate risks to population subgroups such as people along transport routes, people at stops, and crewman. The stops model, which calculates the dose to persons adjacent to the transport vehicle while it is stopped, frequently provides the largest contribution to incident-free radiological impacts. Components such as distances from the vehicle containing radioactive material to nearby people at stops, stop duration, and number of crew members are required for the stops model as well as other incident-free models. To provide supporting data for RADTRAN II based on operational experience, selected truck shipments of radioactive material were observed from origin to destination. Other important aspects of this program were to correlate package size to effective shipment transport index (TI) using radiological surveys and to characterize population distributions and proximities of people to the shipment at a generic truck stop

  2. Solar hydrogen for urban trucks

    Provenzano, J.: Scott, P.B.; Zweig, R. [Clean Air Now, Northridge, CA (United States)

    1997-12-31

    The Clean Air Now (CAN) Solar Hydrogen Project, located at Xerox Corp., El Segundo, California, includes solar photovoltaic powered hydrogen generation, compression, storage and end use. Three modified Ford Ranger trucks use the hydrogen fuel. The stand-alone electrolyzer and hydrogen dispensing system are solely powered by a photovoltaic array. A variable frequency DC-AC converter steps up the voltage to drive the 15 horsepower compressor motor. On site storage is available for up to 14,000 standard cubic feet (SCF) of solar hydrogen, and up to 80,000 SCF of commercial hydrogen. The project is 3 miles from Los Angeles International airport. The engine conversions are bored to 2.9 liter displacement and are supercharged. Performance is similar to that of the Ranger gasoline powered truck. Fuel is stored in carbon composite tanks (just behind the driver`s cab) at pressures up to 3600 psi. Truck range is 144 miles, given 3600 psi of hydrogen. The engine operates in lean burn mode, with nil CO and HC emissions. NO{sub x} emissions vary with load and rpm in the range from 10 to 100 ppm, yielding total emissions at a small fraction of the ULEV standard. Two trucks have been converted for the Xerox fleet, and one for the City of West Hollywood. A public outreach program, done in conjunction with the local public schools and the Department of Energy, introduces the local public to the advantages of hydrogen fuel technologies. The Clean Air Now program demonstrates that hydrogen powered fleet development is an appropriate, safe, and effective strategy for improvement of urban air quality, energy security and avoidance of global warming impact. Continued technology development and cost reduction promises to make such implementation market competitive.

  3. Sexual behavior among truck drivers.

    Singh, Rajiv Kumar; Joshi, Hari Shankar

    2012-01-01

    A cross-sectional study was conducted on Lucknow highway in Bareilly district of Uttar Pradesh to study the knowledge of truck drivers about HIV transmission and prevention and to study the sexual behaviour of these drivers with reference to HIV/AIDS. Age, marital status, education, income, drinking alcohol, length of stay away from home, knowledge about transmission and prevention of HIV, and HIV-prone behavior of truck drivers were studied. Chi-square, mean, and SD were calculated. In all, 289 (97.6%) drivers had heard about HIV/AIDS. Only 242 (81.8%) were aware of HIV transmission by heterosexual route. Misconceptions such as HIV transmission by mosquito bites, living in same room, shaking hands, and sharing food were found. Out of 174 (58.8%) who visited Commercial Sex Workers (CSW), 146 (83.9%) used a condom. 38 (12.8%) visited more than 5 CSW in the last 3 months. Time away from home on the road, marital status, alcohol use, and income class were associated with visiting CSW. High-risk behavior was established in the study population. Safe sex and use of condoms need to be promoted among the truck drivers and better condom availability needs to be assured on highways.

  4. Scientific and technical guidance on foods for special medical purposes in the context of Article 3 of Regulation (EU) No 609/20131

    Sjödin, Anders Mikael

    2015-01-01

    Following a request from the European Commission, the EFSA Panel on Dietetic products, Nutrition and Allergies (NDA) was asked to provide scientific and technical guidance on foods for special medical purposes in the context of Article 3 of Regulation (EU) No 609/2013. The guidance presented...... from the evaluation of dossiers for specific food products notified as FSMP, and in the light of future Community guidelines and legislation. The scope of this guidance is limited to FSMPs in the context of Article 3 of Regulation (EU) No 609/2013. Out of the scope of this guidance are: a) other...

  5. Determinants of fuel consumption in mining trucks

    Dindarloo, Saeid R.; Siami-Irdemoosa, Elnaz

    2016-01-01

    Analysis of fuel consumption in a large surface mine, during more than 5000 cycles of material transportation, revealed considerable variability in the data. Truck fuel estimation based on the mining truck manufacturers' manuals/estimates is not capable of capturing this variability in the fuel consumption data. Partial least squares regression and autoregressive integrated moving average methods were employed to examine the effect of cyclic activities on fuel consumption, and to recommend relevant remedies for consumption reduction. Proper modifications of the operation can result in improved cycle times. Consequently, minimizing some cyclic activities would enhance energy efficiency. The truck “empty idle time” was a major contributor to unnecessary fuel consumption. Since the truck queues at shovels are a major component of the “empty idle time”, decisions should be reviewed to reduce the truck queues at loading points. Improved dispatching strategies, optimal muck pile shape and size distribution, and improved shovel/loader operator skills are effective preventive measures to minimize truck flow bottlenecks at loading points, and thus to improve energy efficiency at mines. - Highlights: • A large fleet of mining trucks consumes considerable amounts of energy. • Current energy models do not consider the effect of site-specific mining conditions. • A new methodology based on material handling cyclic activities is proposed. • Fuel consumption rates in different truck operating modes are determined. • The new model is compared with the truck manufacturer's energy consumption guideline.

  6. Business plan of a food truck in Saint Petersburg

    Zavyalova, Ekaterina

    2017-01-01

    The purpose of the thesis was to investigate how to write a proper business plan and then implement gained knowledge in creating a business plan of a food truck in Saint Petersburg. A business plan serves as a guide for an entrepreneur in the process of company establishment and enables to gain funding from potential investors. The primary objective was to study essential components of a business plan. The theoretical framework comprises of core issues on company establishment and desc...

  7. Benefit of energy absorption by the truck in a frontal car-to-truck collision

    Coo, P.J.A. de; Adalian, C.

    2000-01-01

    EEVC Working Group 14 is investigating the effect of fixing energy absorbing front underrun protection systems (eaFUPS) to trucks instead of rigid devices in order to reduce the injury severity to car occupants in car-to-truck frontal collisions. Three car-to-truck crash tests with cars from

  8. Evaluating sustainability of truck weight regulations: A system dynamics view

    Pei Liu

    2015-11-01

    Full Text Available Purpose: Targeting the problem of overload trucking in Highway Transportation of iron ore from Caofeidian to Tangshan (HTCT, this paper aims to assess long-term effects of alternative Truck Weight Regulation (TWR policies on sustainability of HTCT. Design/methodology/approach: A system dynamics model was established for policy evaluation. The model, composed of six interrelating modules, is able to simulate policies effects on trucking issues such as freight flow, truck traffic flow, pavement performance, highway transport capacity and trucking time, and further on the Cumulative Economic Cost (CEC including transport cost and time cost of freight owners and the Cumulative Social Cost (CSC including pavement maintenance cost, green house gas emission cost, air pollutants emission cost and traffic accidents cost, so the effects of TWR policies on sustainability of HTCT could be evaluated. Findings: According to different values of overload ratio which a TWR policy allows, alternative TWR policies are classified into three types, which are The Rigid Policy (TRP, The Moderate Policy (TMP and The Tolerant Policy (TTP. Results show that the best policy for sustainability of HTCT depends on the importance of CSC which is expected by the local government. To be specific, (1 if CSC is considered much less important than CEC, the local government should continue implementing the current TTP with the maximum overload ratio; (2 if CSC is considered much more important than CEC, then TRP is recommended; and (3 if CSC is considered slightly more important than CES, TMP with overload ratio of 80% is the best. Practical implications: Conclusions of this paper may help the local government design appropriate TWR policies to achieve sustainability of HTCT. Originality/value: To the best of our knowledge, this is the first effort to evaluate TWR policies on sustainability of regional freight transportation based on system dynamics modeling.

  9. Developing a GPS-based truck freight performance measure platform.

    2010-05-01

    Although trucks move the largest volume and value of goods in urban areas, relatively little is known about their travel : patterns and how the roadway network performs for trucks. Global positioning systems (GPS) used by trucking : companies to mana...

  10. Trucks involved in fatal accidents codebook 2008.

    2011-01-01

    This report provides documentation for UMTRIs file of Trucks Involved in Fatal Accidents : (TIFA), 2008, including distributions of the code values for each variable in the file. The 2008 : TIFA file is a census of all medium and heavy trucks invo...

  11. Truck drivers as stakeholders in cooperative driving

    de Bruijn, F.; Terken, J.M.B.; Aarts, E.; de Ruyter, B.; Markopoulos, P.; van Loenen, E.; Wichert, R.; Schouten, B.; Terken, J.M.B.; van Kranenburg, R.; Den Ouden, E.; O'Hare, G.

    2014-01-01

    Cooperative driving for trucks has been claimed to bring substantial benefits for society and fleet owners because of better throughput and reduced fuel consumption, but benefits for truck drivers are questionable. While most work on cooperative driving focuses on the technology, the current paper

  12. Heavy truck rollover characterization (phase B).

    2009-09-01

    The Heavy Truck Rollover Characterization Study - Phase-B builds on the results of prior phases of research. Phases 1 and 2 (Funded by Federal Highway Administration) involved heavy truck rollover characterization for a tractor and box-trailer; and P...

  13. Trusted Truck(R) II (phase A).

    2009-01-01

    The Trusted Truck Program was initiated in 2003 as a joint effort by NTRCI, Volvo and UT. The vision of the Trusted Truck program is to develop a secure and "trusted" transport solution from pickup to delivery. The program's objective is to incre...

  14. Fuel Cell Powered Lift Truck

    Moulden, Steve [Sysco Food Service, Houston, TX (United States)

    2015-08-20

    This project, entitled “Recovery Act: Fuel Cell-Powered Lift Truck Sysco (Houston) Fleet Deployment”, was in response to DOE funding opportunity announcement DE-PS36-08GO98009, Topic 7B, which promotes the deployment of fuel cell powered material handling equipment in large, multi-shift distribution centers. This project promoted large-volume commercialdeployments and helped to create a market pull for material handling equipment (MHE) powered fuel cell systems. Specific outcomes and benefits involved the proliferation of fuel cell systems in 5-to 20-kW lift trucks at a high-profile, real-world site that demonstrated the benefits of fuel cell technology and served as a focal point for other nascent customers. The project allowed for the creation of expertise in providing service and support for MHE fuel cell powered systems, growth of existing product manufacturing expertise, and promoted existing fuel cell system and component companies. The project also stimulated other MHE fleet conversions helping to speed the adoption of fuel cell systems and hydrogen fueling technology. This document also contains the lessons learned during the project in order to communicate the successes and difficulties experienced, which could potentially assist others planning similar projects.

  15. Upgrades for truck transportation of SNM in the Russian Federation

    Gardner, B.H.; Kornilovich, E.

    1998-01-01

    The goal of this project is the rapid reduction of risk to truck transportation of SNM in Russia. Enhanced protection is being accomplished by cooperation between the US Department of Energy, MINATOM of Russia, the Russian Ministry of Defense, and various Russian Institutes. This program provides an integrated program of specialized trucks that are equipped with hardened overpack (SNM vault) containers, alarm and communications systems, and armored cabs. Armored escort vehicles are also provided to increase the survivability of the guards escorting convoys. Only indigenous Russian equipment, modified and/or manufactured by Designing Bureau for Motor Vehicle Transport Equipment (KBATO), is provided under this program. The US will not provide assistance in the truck transportation arena without a commitment from the Russian facility to provide heavily armed escorts for SNM movement. Each site conducts a detailed transportation needs assessment study that is used as the basis for prioritizing assistance. The Siberian Chemical Combine (Tomsk-7) was the initial site of cooperation. The designs used at Tomsk-7 are serving as the baseline for all future vehicles modified under this program. In FY98, many vehicles systems have been ordered for various institutes. Many additional systems will be ordered in FY99

  16. Special Purpose Buoys - USACE IENC

    Department of Homeland Security — These inland electronic Navigational charts (IENCs) were developed from available data used in maintenance of Navigation channels. Users of these IENCs should be...

  17. Recipe and technology development for minced canned products of special purpose based on the underutilized north region fishery object (thorny skate

    Raibulov S. P.

    2016-09-01

    Full Text Available The paper presents the results of justifying the use of thorny skate in the technology of minced meat canned products of special purpose. The key criterion determined the specialized purpose of canned food is the high content of physiologically functional food ingredient of chondroitin sulfate in the cartilage of thorny skate wings. The high content of chondroitin sulfate in raw materials ensures that the content of the physiologically functional ingredient in the finished canned food will be at the level from 220 to 250 mg per 100 g of product. The method of IR blanching is presented for removing urea from the thorny skate muscle tissue. To confirm the efficiency of the developed method of urea removal, it has been proposed to use a modified photocolorimetric method for determination of mass fractions of urea in feed flour according to the governmental standard GOST R 50032–92 "Feed flour made of fish, marine mammals, crustaceans and invertebrates. Methods of determining the mass fraction of urea and calculation of the crude protein with a given mass fraction of carbamide". With the help of this technique, the efficiency of urea removal from the thorny skate tissue by the proposed method has been determined. The residual urea content in the meat of thorny skate after IR blanching is 0.76 %, which is two times lesser than border value of sensitivity of the person (approximated as 1.2 %. The paper presents the materials of experimental substantiation of optimum formulation of new canned meat based on the method of fuzzy modeling. The ratio of the main components of the meatballs recipe (thorny skate and Atlantic cod close to the optimum is 48 % by weight of meat for each component separately.

  18. Toy Trucks in Video Analysis

    Buur, Jacob; Nakamura, Nanami; Larsen, Rainer Rye

    2015-01-01

    discovered that using scale-models like toy trucks has a strongly encouraging effect on developers/designers to collaboratively make sense of field videos. In our analysis of such scale-model sessions, we found some quite fundamental patterns of how participants utilise objects; the participants build shared......Video fieldstudies of people who could be potential users is widespread in design projects. How to analyse such video is, however, often challenging, as it is time consuming and requires a trained eye to unlock experiential knowledge in people’s practices. In our work with industrialists, we have...... narratives by moving the objects around, they name them to handle the complexity, they experience what happens in the video through their hands, and they use the video together with objects to create alternative narratives, and thus alternative solutions to the problems they observe. In this paper we claim...

  19. South Coast Air Quality Management District Truck Testing | Transportation

    Research | NREL South Coast Air Quality Management District Truck Evaluation South Coast Air Quality Management District Truck Evaluation Photo of heavy-duty truck cab. Electric drayage truck Cargo Transportation project, conducted in partnership with the South Coast Air Quality Management

  20. 19 CFR 123.41 - Truck shipments transiting Canada.

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Truck shipments transiting Canada. 123.41 Section... OF THE TREASURY CUSTOMS RELATIONS WITH CANADA AND MEXICO United States and Canada In-Transit Truck Procedures § 123.41 Truck shipments transiting Canada. (a) Manifest required. Trucks with merchandise...

  1. Large Truck Crash Causation Study (LTCCS)

    Department of Transportation — The Large Truck* Crash Causation Study (LTCCS) is based on a three-year data collection project conducted by the Federal Motor Carrier Safety Administration (FMCSA)...

  2. Truck side guard specifications : recommended standard

    2016-09-01

    This document is intended to be used by (1) public or private medium/heavy-duty truck fleets considering adding side guards; (2) jurisdictions or customers that require side guards through policy or procurement; (3) manufacturers of side guards; and ...

  3. Slow speed object detection for haul trucks

    NONE

    2009-09-15

    Caterpillar integrates radar technology with its current camera based system. Caterpillar has developed the Integrated Object Detection System, a slow speed object detection system for mining haul trucks. Object detection is a system that aids the truck operator's awareness of their surroundings. The system consists of a color touch screen display along with medium- and short-range radar as well as cameras, harnesses and mounting hardware. It is integrated into the truck's Work Area Vision System (WAVS). After field testing in 2007, system commercialization began in 2008. Prototype systems are in operation in Australia, Utah and Arizona and the Integrated Object Detection System will be available in the fourth quarter of 2009 and on production trucks 785C, 789C, 793D and 797B. The article is adapted from a presentation by Mark Richards of Caterpillar to the Haulage & Loading 2009 conference, May, held in Phoenix, AZ. 1 fig., 5 photos.

  4. Bombom para dietas especiais: avaliação química e sensorial Chocolate confectionery for special purposes: chemical and sensorial evaluation

    Marissol Richter

    2007-03-01

    Full Text Available Bombom é o produto constituído por massa de chocolate ou por um núcleo formado de recheios diversos, recobertos por uma camada de chocolate. Alimentos para fins especiais (diet são aqueles nos quais ocorrem modificações no conteúdo de nutrientes, adequados à utilização em dietas diferenciadas. O termo light pode ser utilizado quando for cumprido o atributo de redução mínima de 25% no valor energético total ou no conteúdo de nutrientes de alimentos comparados. Foram desenvolvidos um bombom controle e formulações de bombons diet/light, sendo apenas uma formulação selecionada para estudo. Um bombom comercial foi utilizado como referência. Foram elaboradas análises químicas (obtenção do valor calórico e análise sensorial (teste de aceitação com escala hedônica híbrida para avaliação dos produtos. A substituição dos açúcares por edulcorantes e agentes de corpo foi satisfatória, assim como o uso do substituto de gordura Benefat®. Na análise sensorial, o bombom especial obteve altos níveis de intenção de compra, podendo nesta análise ser considerado como um produto de grande potencial de mercado.Chocolate confectionery is a product consisting of either chocolate mass or a nucleus containing several fillings covered with a chocolate layer. Foods for special purposes are those in which modifications are made in what is related to the nutrients content, adapted to the utilization in differentiated diets. The term light is applied to a product providing it fulfils the attribute of a 25% minimum reduction in the total energetic value or nutrients content if compared to a similar, standard product. Two series of chocolate confectionery samples were prepared: a control sample and ten diet and light formulations, and one of these formulations was selected. A commercial chocolate confectionery was used as reference. The chocolate confectionery samples (control and special were compared using chemical and sensorial

  5. Active Suspension of Truck Seat

    Masaaki Kawana

    1998-01-01

    Full Text Available The driver’s seat of a heavy duty truck is usually mounted on a spring–damper assembly anchored to the cab floor. To improve riding comfort, this study investigated the effects of mounting a computer-controlled actuator in parallel with the traditional spring–damper assembly. A dynamic model of the seat is represented by a two degree-of-freedom system, including a cushion. In this paper, a control system is designed, using optimal control theory, which minimizes rms vertical acceleration at a point representing the driver’s hip point. In this system, accelerations of the hip point, the seat frame and the cab floor are picked up and integrated to obtain the state variables to be fed back and fed forward to the actuator through a digital computer. The actuator is constructed with electric servo-motor and ball-screw mechanism. The experimental study was carried out on a shaker, which simulates the vibrations of the cab floor in actual service. Results were obtained for both a dummy and a real human body. The vibration test produced rms accelerations of the seat and the hip point of about 1.0 m/s2 without the actuator, while the rms accelerations were suppressed to about 0.5 m/s2 at a rms input voltage to the servo-motor of 1.0 V.

  6. Diesel Engine Light Truck Application

    None

    2007-12-31

    The Diesel Engine Light Truck Application (DELTA) program consists of two major contracts with the Department of Energy (DOE). The first one under DE-FC05-97-OR22606, starting from 1997, was completed in 2001, and consequently, a final report was submitted to DOE in 2003. The second part of the contract was under DE-FC05-02OR22909, covering the program progress from 2002 to 2007. This report is the final report of the second part of the program under contract DE-FC05-02OR22909. During the course of this contract, the program work scope and objectives were significantly changed. From 2002 to 2004, the DELTA program continued working on light-duty engine development with the 4.0L V6 DELTA engine, following the accomplishments made from the first part of the program under DE-FC05-97-OR22606. The program work scope in 2005-2007 was changed to the Diesel Particulate Filter (DPF) soot layer characterization and substrate material assessment. This final report will cover two major technical tasks. (1) Continuation of the DELTA engine development to demonstrate production-viable diesel engine technologies and to demonstrate emissions compliance with significant fuel economy advantages, covering progress made from 2002 to 2004. (2) DPF soot layer characterization and substrate material assessment from 2005-2007.

  7. Gas fuelled heavy-duty trucks for municipal services

    Forsberg, A. (City of Helsinki Construction Services (Finland)); Hietanen, L. (Lassila and Tikanoja, Jyvaeskylae (Finland)); Nylund, N.-O. (TEC TransEnergy Consulting, Espoo (Finland))

    2009-07-01

    Helsinki City Public Works Department (HKR) and the environmental management company Lassila and Tikanoja joined forces to demonstrate the suitability of heavy-duty gas fuelled trucks for municipal services. HKR acquired two and Lassila and Tikanoja five Mercedes-Benz Econic trucks. HKR's trucks are equipped with interchangeable platforms, Lassila an Tikanoja's trucks with refuse collection equipment. The trucks are subjected to a two-year follow-up study to establish reliability, operational costs and exhaust emissions. Diesel trucks representing up-to-date technology are used as reference. If the gas fuelled trucks perform well, this can lead to increased numbers of natural gas trucks in municipal services, and in the long run to the introduction of biogas fuelled trucks. (orig.)

  8. Ticketing aggressive cars and trucks (TACT): How does it work on city streets?

    Telford, Russell; Cook, Lawrence J; Olson, Lenora M

    2018-02-17

    The purpose of this study was to determine the feasibility of modifying the Ticking Aggressive Cars and Trucks (TACT) program, originally designed to work on state highways, within a metropolitan area to reduce unsafe interactions and their related crashes between drivers of large trucks and passenger vehicles. Using crash data, the driving behaviors most commonly associated with large truck and passenger vehicle crashes were identified. A public awareness campaign using media messaging and increased law enforcement was created targeting these associated behaviors. The frequency of these behaviors both before and after the public awareness campaign was determined through observation of traffic at 3 specific locations within the city. Each location had a sufficient volume of large truck and passenger traffic to observe frequent interactions. Pre- and postintervention data were compared using negative binomial regression with generalized estimating equations to evaluate whether the campaign was associated with a reduction in the identified driving behaviors. A comparison between crash data from before, during, and after the campaign and crashes during the same time periods in previous years did not show a significant difference (P =.081). The number of large trucks observed in traffic remained the same during pre- and postintervention periods (P =.625). The rates of negative interactions per 100 large trucks decreased for both large trucks and passenger vehicles after the intervention, with calculated rate ratios of 0.58 (95% confidence interval [CI], 0.48, 0.70) and 0.31 (95% CI, 0.20, 0.47). The greatest reduction was seen in passenger vehicles following too close, with a rate ratio of 0.21 (95% CI, 0.15, 0.30). Although designed for reducing crashes on highways, the TACT program can be an effective approach for improving driver behaviors on city streets.

  9. Sizing stack and battery of a fuel cell hybrid distribution truck

    Bram Veenhuizen; P. van den Bosch; T. Hofman; Edwin Tazelaar; Y. Shen

    2012-01-01

    An existing fuel cell hybrid distribution truck, built for demonstration purposes, is used as a case study to investigate the effect of stack (kW) and battery (kW, kWh) sizes on the hydrogen consumption of the vehicle. Three driving cycles, the NEDC for Low Power vehicles, CSC and JE05 cycle, define

  10. Ecodriving acceptance : an experimental study on anticipation behavior of truck drivers

    Thijssen, R.J.T.G.; Hofman, T.; Ham, J.R.C.

    2014-01-01

    In this paper, it is researched to what extend truck drivers are willing to improve their anticipation behavior. For the purpose of this research, anticipation behavior is characterized by anticipation distance: the distance to a stopping point (e.g. roundabout), at which the accelerator pedal is

  11. Stressful work, psychological job strain, and turnover: A 2-year prospective cohort study of truck drivers

    Croon, E.M.de; Sluiter, J.K.; Blonk, R.W.B.; Broersen, J.P.J.; Frings-Dresen, M.H.W.

    2004-01-01

    Based on a model that combines existing organizational stress theory and job transition theory, this 2-year longitudinal study examined antecedents and consequences of turnover among Dutch truck drivers. For this purpose, self-reported data on stressful work (job demands and control), psychological

  12. The open-pit truck dispatching method based on the completion of production target and the truck flow saturation

    Xing, J.; Sun, X. [Northeastern University, Shenyang (China)

    2007-05-15

    To address current problems in the 'modular dispatch' dynamic programming system widely used in open-pit truck real-time dispatching, two concepts for meeting production targets and truck flow saturation were proposed. Using truck flow programming and taking into account stochastic factors and transportation distance, truck real-time dispatching was optimised. The method is applicable to both shovel-truck match and mismatching and also to empty and heavy truck dispatching. In an open-pit mine the production efficiency could be increased by between 8% and 18%. 6 refs.

  13. An exploratory study of long-haul truck drivers' secondary tasks and reasons for performing them.

    Iseland, Tobias; Johansson, Emma; Skoog, Siri; Dåderman, Anna M

    2018-08-01

    Research on drivers has shown how certain visual-manual secondary tasks, unrelated to driving, increase the risk of being involved in crashes. The purpose of the study was to investigate (1) if long-haul truck drivers in Sweden engage in secondary tasks while driving, what tasks are performed and how frequently, (2) the drivers' self-perceived reason/s for performing them, and (3) if psychological factors might reveal reasons for their engaging in secondary tasks. The study comprised 13 long-haul truck drivers and was conducted through observations, interviews, and questionnaires. The drivers performed secondary tasks, such as work environment related "necessities" (e.g., getting food and/or beverages from the refrigerator/bag, eating, drinking, removing a jacket, face rubbing, and adjusting the seat), interacting with a mobile phone/in-truck technology, and doing administrative tasks. The long-haul truck drivers feel bored and use secondary tasks as a coping strategy to alleviate boredom/drowsiness, and for social interaction. The higher number of performed secondary tasks could be explained by lower age, shorter driver experience, less openness to experience, lower honesty-humility, lower perceived stress, lower workload, and by higher health-related quality of life. These explanatory results may serve as a starting point for further studies on large samples to develop a safer and healthier environment for long-haul truck drivers. Copyright © 2018. Published by Elsevier Ltd.

  14. Development of Auto-Stacking Warehouse Truck

    Kuo-Hsien Hsia

    2018-03-01

    Full Text Available Warehouse automation is a very important issue for the promotion of traditional industries. For the production of larger and stackable products, it is usually necessary to operate a fork-lifter for the stacking and storage of the products by a skilled person. The general autonomous warehouse-truck does not have the ability of stacking objects. In this paper, we develop a prototype of auto-stacking warehouse-truck that can work without direct operation by a skill person. With command made by an RFID card, the stacker truck can take the packaged product to the warehouse on the prior-planned route and store it in a stacking way in the designated storage area, or deliver the product to the shipping area or into the container from the storage area. It can significantly reduce the manpower requirements of the skilled-person of forklift technician and improve the safety of the warehousing area.

  15. Large truck and bus crash facts, 2008. 

    2010-03-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2008. Selected crash statistics on passenger : vehicles are also presen...

  16. Optimization of a truck-drone in tandem delivery network using k-means and genetic algorithm

    Sergio Mourelo Ferrandez

    2016-04-01

    Full Text Available Purpose: The purpose of this paper is to investigate the effectiveness of implementing unmanned aerial delivery vehicles in delivery networks. We investigate the notion of the reduced overall delivery time, energy, and costs for a truck-drone network by comparing the in-tandem system with a stand-alone delivery effort. The objectives are (1 to investigate the time, energy, and costs associated to a truck-drone delivery network compared to standalone truck or drone, (2 to propose an optimization algorithm that determines the optimal number of launch sites and locations given delivery requirements, and drones per truck, (3 to develop mathematical formulations for closed form estimations for the optimal number of launch locations, optimal total time, as well as the associated cost for the system. Design/methodology/approach: The design of the algorithm herein computes the minimal time of delivery utilizing K-means clustering to find launch locations, as well as a genetic algorithm to solve the truck route as a traveling salesmen problem (TSP. The optimal solution is determined by finding the minimum cost associated to the parabolic convex cost function. The optimal min-cost is determined by finding the most efficient launch locations using K-means algorithms to determine launch locations and a genetic algorithm to determine truck route between those launch locations.  Findings: Results show improvements with in-tandem delivery efforts as opposed to standalone systems. Further, multiple drones per truck are more optimal and contribute to savings in both energy and time. For this, we sampled various initialization variables to derive closed form mathematical solutions for the problem. Originality/value: Ultimately, this provides the necessary analysis of an integrated truck-drone delivery system which could be implemented by a company in order to maximize deliveries while minimizing time and energy. Closed-form mathematical solutions can be used as

  17. Alternative Fuels Data Center: Biodiesel Truck Transports Capitol Christmas

    Tree Biodiesel Truck Transports Capitol Christmas Tree to someone by E-mail Share Alternative Fuels Data Center: Biodiesel Truck Transports Capitol Christmas Tree on Facebook Tweet about Alternative Fuels Data Center: Biodiesel Truck Transports Capitol Christmas Tree on Twitter Bookmark Alternative

  18. Case Study: Natural Gas Regional Transport Trucks

    Laughlin, M.; Burnham, A.

    2016-08-01

    Learn about Ryder System, Inc.'s experience in deploying nearly 200 CNG and LNG heavy-duty trucks and construction and operation of L/CNG stations using ARRA funds. Using natural gas in its fleet, Ryder mitigated the effects of volatile fuel pricing and reduced lifecycle GHGs by 20% and petroleum by 99%.

  19. Light Duty Truck Characteristics, Historical Data Base

    1979-12-01

    The report is a collection of data concerning physical, operating, performance, and market characteristics of light duty trucks for the model years 1972 and 1975 thru 1977. The data is stored on tape in DOT/TSC DEC System 10 computer system. Informat...

  20. Light Truck Characteristics, Historical Data Base

    1980-11-01

    The report is a description of the data about the physical, operating performance, and market characteristics of light trucks for the model years 1955 through 1977, which is stored on tape in DOT/TSC DEC System 10 computer system. Vehicles are report...

  1. INTRALOG, intelligent autonomous truck applications in Logistics

    MSc Berry Gerrits; Dr. Frans Tillema; MMC A.F. Spruijt; MSc Leo Buning

    2016-01-01

    INTRALOG is a project, to better use of materials, there by leading to improvements for People (better safety, lower physical work load), Planet (lower emissions and energy/ fuel con started September 2015, in which Automated Guided Truck Applications will be developed. Automated systems typically

  2. Research of Acoustic Properties of Materials with the Purpose of Their Use at Design of Special Noise Protective Clothes for Oil and Gas Industry

    Drofa, E. A.; Lipilina, E. Yu

    2018-01-01

    The article is devoted to the substantiation of the choice of a rational package of materials, which has the greatest noise-protective properties when designing special clothes with reference to the oil and gas industry. Studies were conducted to assess the factors that have the most significant effect on the noise-protective properties of clothing. Conclusions are made about the possibility of using the developed technique for studying the noise-protective properties of materials in selecting rational packages of materials for the production of special clothes with high noise-protective properties.

  3. Feasibility of landfill gas as a liquefied natural gas fuel source for refuse trucks.

    Zietsman, Josias; Bari, Muhammad Ehsanul; Rand, Aaron J; Gokhale, Bhushan; Lord, Dominique; Kumar, Sunil

    2008-05-01

    The purpose of this paper is to develop a methodology to evaluate the feasibility of using landfill gas (LFG) as a liquefied natural gas (LNG) fuel source for heavy-duty refuse trucks operating on landfills. Using LFG as a vehicle fuel can make the landfills more self-sustaining, reduce their dependence on fossil fuels, and reduce emissions and greenhouse gases. Acrion Technologies Inc. in association with Mack Trucks Inc. developed a technology to generate LNG from LFG using the CO2 WASH process. A successful application of this process was performed at the Eco Complex in Burlington County, PA. During this application two LNG refuse trucks were operated for 600 hr each using LNG produced from gases from the landfill. The methodology developed in this paper can evaluate the feasibility of three LFG options: doing nothing, electricity generation, and producing LNG to fuel refuse trucks. The methodology involved the modeling of several components: LFG generation, energy recovery processes, fleet operations, economic feasibility, and decision-making. The economic feasibility considers factors such as capital, maintenance, operational, and fuel costs, emissions and tax benefits, and the sale of products such as surplus LNG and food-grade carbon dioxide (CO2). Texas was used as a case study. The 96 landfills in Texas were prioritized and 17 landfills were identified that showed potential for converting LFG to LNG for use as a refuse truck fuel. The methodology was applied to a pilot landfill in El Paso, TX. The analysis showed that converting LFG to LNG to fuel refuse trucks proved to be the most feasible option and that the methodology can be applied for any landfill that considers this option.

  4. A Qualitative Study of Migrant-related Stressors, Psychosocial Outcomes and HIV Risk Behavior among Truck Drivers in Zambia

    Ncube, Nomagugu; Simona, Simona J.; Kansankala, Brian; Sinkala, Emmanuel; Raidoo, Jasmin

    2017-01-01

    Truck drivers are part of mobile populations which have been noted as a key population at risk of HIV in Zambia. This study was aimed at 1) determining Potentially Traumatic Events (PTEs), labor migrant-related stressors, psychosocial problems and HIV risk behaviors among truck drivers in Zambia and 2) examining the relationship between PTEs, migrant-related stressors, psychosocial outcomes and HIV sexual risk behavior among truck drivers in Zambia. We conducted fifteen semi-structured interviews with purposively sampled male truck drivers at trucking companies in Lusaka, Zambia. Findings indicate that truck drivers experience multiple stressors and potentially traumatic incidences, including delays and long waiting hours at borders, exposure to crime and violence, poverty, stress related to resisting temptation of sexual interactions with sex workers or migrant women, and job-related safety concerns. Multiple psychosocial problems such as intimate partner violence, loneliness, anxiety and depression-like symptoms were noted. Transactional sex, coupled with inconsistent condom use were identified as HIV sexual risk behaviors. Findings suggest the critical need to develop HIV prevention interventions which account for mobility, potentially traumatic events, psychosocial problems, and the extreme fear of HIV testing among this key population. PMID:27681145

  5. Optimization of a truck-drone in tandem delivery network using k-means and genetic algorithm

    Ferrandez, S. M.; Harbison, T.; Weber, T.; Sturges, R.; Rich, R.

    2016-07-01

    The purpose of this paper is to investigate the effectiveness of implementing unmanned aerial delivery vehicles in delivery networks. We investigate the notion of the reduced overall delivery time, energy, and costs for a truck-drone network by comparing the in-tandem system with a stand-alone delivery effort. The objectives are (1) to investigate the time, energy, and costs associated to a truck-drone delivery network compared to standalone truck or drone, (2) to propose an optimization algorithm that determines the optimal number of launch sites and locations given delivery requirements, and drones per truck, (3) to develop mathematical formulations for closed form estimations for the optimal number of launch locations, optimal total time, as well as the associated cost for the system. The design of the algorithm herein computes the minimal time of delivery utilizing K-means clustering to find launch locations, as well as a genetic algorithm to solve the truck route as a traveling salesmen problem (TSP). The optimal solution is determined by finding the minimum cost associated to the parabolic convex cost function. The optimal min-cost is determined by finding the most efficient launch locations using K-means algorithms to determine launch locations and a genetic algorithm to determine truck route between those launch locations. Results show improvements with in-tandem delivery efforts as opposed to standalone systems. Further, multiple drones per truck are more optimal and contribute to savings in both energy and time. For this, we sampled various initialization variables to derive closed form mathematical solutions for the problem. Ultimately, this provides the necessary analysis of an integrated truck-drone delivery system which could be implemented by a company in order to maximize deliveries while minimizing time and energy. Closed-form mathematical solutions can be used as close estimators for final costs and time. (Author)

  6. 2015 E-Truck Task Force: Key Barriers Affecting E-Truck Adoption, Industry and Policy Implications, and Recommendations to Move the Market Forward

    Brotherton, Tom; Gilde, Alycia; Tomic, Jasna

    2016-01-01

    CALSTART’s E-Truck Task Force (ETTF) produced a report outlining the markets for electric drive trucks (E-Trucks), the prime barriers facing their success and provided key findings and recommendations to support expanding E-Truck adoption. Four key findings have been identified by the E-Truck Task Force as barriers currently affecting the growth and viability of E-Truck sales

  7. Dump truck-related deaths in construction, 1992-2007.

    McCann, Michael; Cheng, Mei-Tai

    2012-05-01

    Dump trucks are universally used in construction and other industries to haul materials to the location and to remove waste materials. The source for dump truck-related fatality data was the Bureau of Labor Statistics Census of Fatal Occupational Injuries (CFOI) Research File. From 1992 to 2007, 829 construction workers were killed in dump truck-related incidents nationwide. Of those, 336 were dump truck operators with 215 deaths occurring in street and highway incidents. Another 343 deaths involved workers on foot, three-quarters struck by dump trucks. Sixty-four of the construction workers killed were maintaining dump trucks, 22 when caught between the truck frame and a falling dump truck bed. Of the 86 other deaths, 55 involved streets and highways. Recommendations include: (i) improving the reporting of seat belt usage in fatality reports; (ii) requiring use of seat belts; (iii) requiring the use of backup alarms, spotters, or other methods to alert dump truck operators to workers in their blind spots; (iv) prohibiting direct dumping at river banks and embankments; (v) using cameras or radar to enforce stopping at railway crossings; and (xi) enforcing worker safety practices (e.g., lockout/tagout procedures on elevated dump truck beds). Copyright © 2011 Wiley Periodicals, Inc.

  8. Voluntary Truck and Bus Fuel-Economy-Program marketing plan. Final technical report, September 29, 1980-January 29, 1982

    None

    1982-01-01

    The aim of the program is to improve the utilization of fuel by commercial trucks and buses by updating and implementing specific approaches for educating and monitoring the trucking industry on methods and means of conserving fuels. The following outlines the marketing plan projects: increase use of program logo by voluntary program members and others; solicit trade publication membership and support; brief Congressional delegations on fuel conservation efforts; increase voluntary program presence before trade groups; increase voluntary program presence at truck and trade shows; create a voluntary program display for use at trade shows and in other areas; review voluntary program graphics; increase voluntary program membership; and produce placemats carrying fuel conservation messages; produce a special edition of Fuel Economy News, emphasizing the driver's involvement in fuel conservation; produce posters carrying voluntary program fuel conservation message. Project objectives, activities, and results for each project are summarized.

  9. Shock and vibration environments for a large shipping container during truck transport (Part II)

    Magnuson, C.E.

    1978-05-01

    Purpose of this study was to obtain vibration and shock data during truck shipment of heavy cargo. These data were for use in determining any trends of vibration and shock environments with increased cargo weight. The new data were obtained on a ''piggyback'' basis during truck transport of 249 100N (56,000-pound) cargo which consisted of a spent fuel container and its supporting structure. The truck was driven from Mercury, Nevada, to Albuquerque, New Mexico. The routes traveled were US 95 from Mercury, Nevada, to Las Vegas, Nevada; US 93 from Las Vegas to Kingman, Arizona; and I-40/US 66 from Kingman to Albuquerque, New Mexico. Speeds varied from very slow to 88 km/hr (55 mph). A comparison of data from similar experiments with cargo weights varying from no-load to this load shows that the zero-to-peak acceleration amplitude levels of vibration are highest when trucks carry relatively light loads. This is true for the longitudinal and vertical axes of the vehicles in most frequency bands and for the transverse axis above 700 Hz. The shock response acceleration amplitudes for heavier cargo weights were less severe above 3 Hz in the vertical axis and higher between 8 and 20 Hz in the transverse axis. The highest acceleration amplitude of shock response in the longitudinal axis below about 20 Hz was produced in a trailer having a spring suspension system and carrying the 249 100N (56,000 pounds) load

  10. Reducing truck emissions at container terminals in a low carbon economy

    Chen, Gang; GOVINDAN, Kannan; Golias, Mihalis M.

    2013-01-01

    This study proposes a methodology to optimize truck arrival patterns to reduce emissions from idling truck engines at marine container terminals. A bi-objective model is developed minimizing both truck waiting times and truck arrival pattern change. The truck waiting time is estimated via...... a queueing network. Based on the waiting time, truck idling emissions are estimated. The proposed methodology is evaluated with a case study, where truck arrival rates vary over time. We propose a Genetic Algorithm based heuristic to solve the resulting problem. Result shows that, a small shift of truck...... arrivals can significantly reduce truck emissions, especially at the gate....

  11. COMPETITIVE PRESSURE SYSTEMS MAPPING IN THE BRAZILIAN TRUCK MARKET

    Ricardo Costa da Cruz

    2013-06-01

    Full Text Available The automotive business in Brazil achieved 10% of the industry revenue and 6% of the formal employment by 2008. The commercial vehicle segment concentrated so far eight truck makers that experienced their best market figures in 2008, the economy crisis in 2009, and an extraordinary recovery in 2010. Government tax reduction programs as well as special financing incentives were undoubtedly decisive to re-stimulate the business during the crisis. Positive Brazilian perspectives with the boom in the agricultural, oil and gas, mining and infrastructure activities plus the coming sports events call the attention of new players that are quickly implementing different business strategies to become part of the game. New emission regulations starting from 2012 also bring uncertainties, challenges and opportunities. With the growing globalization and market concentration it's critical for any industry understand and minimize the forces of competitive pressures. The main goal of this paper, therefore, is to contribute to the academy with an alternative approach of strategic and behavioral analysis of rivalry and competition different than the five forces model of Porter. Ford, Iveco, MAN, Mercedes-Benz, Scania and Volvo were assessed from 2008 to 2010 within three main performance indicators – unit sales, gross revenues and operating profits – supporting the elaboration of the competitive pressure systems mapping model of D'aveni, including a hypothetical future scenario with a new entrant and the potential impacts in the system. Main findings and results portray the asymmetrical strategic behavior of competitors and the temporary dynamic stability in the Brazilian truck industry.

  12. Adaptive Virtual Tow Bar and Transition of Control : A truck driving simulator study

    Wilschut, E.S.; Willemsen, D.M.C.; Hogema, J.H.; Martens, M.H.

    2016-01-01

    Background : Truck platooning, with trucks being virtually connected, is getting more and more attention. Truck platooning offers the potential for substantial fuel savings while allowing the truck driver in the platoon to take a rest. However, at the current state of technology, truck drivers are

  13. Raley's LNG Truck Site Final Data Report

    Battelle

    1999-07-01

    Raley's is a 120-store grocery chain with headquarters in Sacramento, California, that has been operating eight heavy-duty LNG trucks (Kenworth T800 trucks with Cummins L10-300G engines) and two LNG yard tractors (Ottawa trucks with Cummins B5.9G engines) since April 1997. This report describes the results of data collection and evaluation of the eight heavy-duty LNG trucks compared to similar heavy-duty diesel trucks operating at Raley's. The data collection and evaluation are a part of the U.S. Department of Energy (DOE)/National Renewable Energy Laboratory (NREL) Alternative Fuel Truck Evaluation Project.

  14. System for selection of radiation source transfer trucks

    Tanimoto, Yoshinori; Ito, Kojiro.

    1970-01-01

    A device for selection of trucks each of which load and transfer a radiation source to an irradiation room above a water pool is installed at the end of a pair of rails fixed to the bottom of the pool. This device is equipped with a number of laterally shiftable rail pairs which may be brought into successive alignment with the fixed rails and is adapted to receive, carry and fix a truck on each rail pair. If one of said trucks is selected for irradiation in a desired irradiation room, the rail pair carrying this truck is shifted to align and couple with the fixed rail pair whereupon the truck is driven and transferred to a position on the fixed rails below the desired room and elevated thereinto. Accordingly, a plurality of trucks can optionally be shunted on a line of fixed rails without unloading the respective radiation sources. (Ohno, Y.)

  15. Effect of truck and rail economic deregulation on radioactive material transportation

    Allen, G.C. Jr.

    1984-01-01

    An evaluation of the effect of truck and rail economic deregulation on radioactive material transportation is presented in this document. The evaluation is based on expected market performance that would be consistent with fundamental economic theories. The issues of transport safety, commodity discrimination and rates are addressed. Relative to transport safety, deregulation should not have any significant impact. While deregulation should not change commodity acceptance and may lower rates for motor carriage, it may allow increased discrimination by rail carriers in addition to raising rates. Consequently, it is likely that the radioactive material transportation industry will continue to place greater reliance on the competitive motor carrier industry. Positive steps that shippers can take are to maintain credible options to ship by alternate modes, to address issues that result in the perceived need for special risk premiums, and to reduce the cost of handling truck shipments by improvements in technology or procedures. 28 references, 3 figures, 6 tables

  16. Improving truck safety: Potential of weigh-in-motion technology

    Bernard Jacob

    2010-07-01

    Full Text Available Trucks exceeding the legal mass limits increase the risk of traffic accidents and damage to the infrastructure. They also result in unfair competition between transport modes and companies. It is therefore important to ensure truck compliance to weight regulation. New technologies are being developed for more efficient overload screening and enforcement. Weigh-in-Motion (WIM technologies allow trucks to be weighed in the traffic flow, without any disruption to operations. Much progress has been made recently to improve and implement WIM systems, which can contribute to safer and more efficient operation of trucks.

  17. COMPUTATIONAL AND EXPERIMENTAL EVALUATION OF TECHNICAL CHARACTERISTICS OF TRUCKS TIRES

    Z. A. Godzhaev

    2015-01-01

    Full Text Available Now improvement of technological design specification of trucks tires develops very much. In modern mechanical engineering polyamide and kapron cords for tires of line-haul trucks and buses are replaced with all-metal ones (AMC even more often. It was defined that at increase in AMC tires production their technical characteristics were investigated insufficiently. In this regard there were carried out bench tests to compare the main operational indicators of domestic (JSC Nizhnekamskshina production and foreign tires with an all-metal cord: 315/60R22.5 the NF-201 model with 315/60r22.5 the XZA2 ENERGY Michelin model (steering; 315/60R22.5 the NR-201 model with 315/60R22.5 the XDA2+ ENERGY Michelin model (drive; 315/80R22.5 the NF-201 model with 315/80R22.5 the 3D Michelin XZE X MultiWay model (steering; 315/80R22.5 the NR-201 model with 315/80R22.5 the 3D XDE X MultiWay model (drive. The laboratory researches were carried out for the purpose of an assessment of the universal, load, damping (hysteresis and other characteristics of tires with use of the universal functional SIB-1M test-bench. It was established that Michelin AMC tires of steering low-profile 315/60R22.5 XZA2 ENERGY models have the best indicators on power heterogeneity - 0.47-0.89 percent. The high-profile AMC tires of drive wheels 315/80R22.5 of the NR-201 model of JSC Nizhnekamskshina have the worst indicators. However, all the tested tires correspond to GOST 5513-97on this indicator. It was noted that Nizhnekamsk AMC tires of the size 315/60R22.5 are flush with AMC tires Michelin on set of operational indicators, except power heterogeneity, and last one of Michelin tires is lower than Nizhnekamsk ones by 2-3 times. It was suggested to conduct further researches on definition of optimum operational tires indicators because of an intensive use of KAMAZ trucks in agricultural production

  18. Universal methods of creation of functionally developed management systems of special purpose of industrial enterprises and production associations and their use when planning and introducing the subsystem of accounting and analytical support

    Tkachenko Sergіy A.

    2013-03-01

    Full Text Available The goal of the article lies in formation of a paradigm (sample of universal methods of creation of functionally developed management systems of special purpose of industrial enterprises and production associations and their use when planning and introducing the subsystem of accounting and analytical support. Analysing, systemising and generalising scientific works of many economists, the article describes ways of solution of the problem of organisation of works on planning and introducing the accounting function at industrial enterprises and in production associations – individual planning, increase of a number of organisations that plan functionally developed accounting subsystem and training of relevant specialists. In the result of the study the article realises an important direction of development in improvement of organisation of accounting and economic and analytical support at industrial enterprises and in production associations based on uniformity of project decisions on the subsystem of the accounting and analytical support and functional development of the process of its creation. The issue of organisation of the calculation process while planning and introducing the accounting function in functionally developed management systems of special purpose of industrial enterprises and production associations is of special urgency among the prospects of further studies in this direction. Further development of accounting can result in replacement of traditional accounting with functionally developed subsystem of accounting and analytical support with intensive use of the concept of methodologically justified paradigmatic approach.

  19. The Obesogenic Environment of Commercial Trucking: A Worksite Environmental Audit and Implications for Systems-Based Interventions

    Apostolopoulos, Yorghos; Lemke, Michael; Sönmez, Sevil; Hege, Adam

    2016-01-01

    Background: Commercial trucker health is a vital public health concern. Enhanced understanding of the multiplicity, diversity, interdependence, and complexity of policies, resources, and stakeholders relevant to healthful living in trucking worksites can guide future interventions. Purpose: This article examines how the environmental attributes of…

  20. UPS CNG Truck Fleet Start Up Experience: Alternative Fuel Truck Evaluation Project

    Walkowicz, K.

    2001-01-01

    UPS operates 140 Freightliner Custom Chassis compressed natural gas (CNG)-powered vehicles with Cummins B5.9G engines. Fifteen are participating in the Alternative Fuel Truck Evaluation Project being funded by DOE's Office of Transportation Technologies and the Office of Heavy Vehicle Technologies

  1. Naturalistic drive cycle synthesis for pickup trucks.

    Liu, Zifan; Ivanco, Andrej; Filipi, Zoran

    2015-09-01

    Future pick-up trucks are meeting much stricter fuel economy and exhaust emission standards. Design tradeoffs will have to be carefully evaluated to satisfy consumer expectations within the regulatory and cost constraints. Boundary conditions will obviously be critical for decision making: thus, the understanding of how customers are driving in naturalistic settings is indispensable. Federal driving schedules, while critical for certification, do not capture the richness of naturalistic cycles, particularly the aggressive maneuvers that often shape consumer perception of performance. While there are databases with large number of drive cycles, applying all of them directly in the design process is impractical. Therefore, representative drive cycles that capture the essence of the naturalistic driving should be synthesized from naturalistic driving data. Naturalistic drive cycles are firstly categorized by investigating their micro-trip components, defined as driving activities between successive stops. Micro-trips are expected to characterize underlying local traffic conditions, and separate different driving patterns. Next, the transitions from one vehicle state to another vehicle state in each cycle category are captured with Transition Probability Matrix (TPM). Candidate drive cycles can subsequently be synthesized using Markov Chain based on TPMs for each category. Finally, representative synthetic drive cycles are selected through assessment of significant cycle metrics to identify the ones with smallest errors. This paper provides a framework for synthesis of representative drive cycles from naturalistic driving data, which can subsequently be used for efficient optimization of design or control of pick-up truck powertrains. Manufacturers will benefit from representative drive cycles in several aspects, including quick assessments of vehicle performance and energy consumption in simulations, component sizing and design, optimization of control strategies, and

  2. Vehicle test report: Battronic pickup truck

    Price, T. W.; Shain, T. W.; Freeman, R. J.; Pompa, M. F.

    1982-01-01

    An electric pickup truck was tested to characterize certain parameters and to provide baseline data that can be used for the comparison of improved batteries that may be incorporated into the vehicle at a later time. The vehicle tests were concentrated on the electrical drive subsystem; i.e., the batteries, controller, and motor. The tests included coastdowns to characterize the road load and range evaluations for both cyclic and constant speed conditions. A qualitative evaluation of the vehicle's performance was made by comparing its constant speed range performance with other vehicles.

  3. Modernization of dump truck onboard system

    Semenov, M. A.; Bolshunova, O. M.; Korzhev, A. A.; Kamyshyan, A. M.

    2017-10-01

    The review of the only automated dispatch system for the career dump trucks, which is presented in the domestic market, was made. A method for upgrading the loading control system and technological weighing process of the career dump was proposed. The cargo weight during loading is determined by the gas pressure in the suspension cylinders at the time of the oscillation ending and at the start of the vibration smoothing process; the smoothing speed correction is performed. The error of the cargo weighting is 2.5-3%, and of the technological weighing process during driving - 1%, which corresponds to the error level of the steady-state weighting means.

  4. Cummins Light Truck Diesel Engine Progress Report

    John H. Stang

    2000-01-01

    The Automotive Market in the United States is moving in the direction of more Light Trucks and fewer Small Cars. The customers for these vehicles have not changed, only their purchase decisions. Cummins has studied the requirements of this emerging market. Design and development of an engine system that will meet these customer needs has started. The engine system is a difficult one, since the combined requirements of a very fuel-efficient commercial diesel, and the performance and sociability requirements of a gasoline engine are needed. Results of early testing are presented which show that the diesel is possibly a good solution

  5. Truck Roll Stability Data Collection and Analysis

    Stevens, SS

    2001-07-02

    The principal objective of this project was to collect and analyze vehicle and highway data that are relevant to the problem of truck rollover crashes, and in particular to the subset of rollover crashes that are caused by the driver error of entering a curve at a speed too great to allow safe completion of the turn. The data are of two sorts--vehicle dynamic performance data, and highway geometry data as revealed by vehicle behavior in normal driving. Vehicle dynamic performance data are relevant because the roll stability of a tractor trailer depends both on inherent physical characteristics of the vehicle and on the weight and distribution of the particular cargo that is being carried. Highway geometric data are relevant because the set of crashes of primary interest to this study are caused by lateral acceleration demand in a curve that exceeds the instantaneous roll stability of the vehicle. An analysis of data quality requires an evaluation of the equipment used to collect the data because the reliability and accuracy of both the equipment and the data could profoundly affect the safety of the driver and other highway users. Therefore, a concomitant objective was an evaluation of the performance of the set of data-collection equipment on the truck and trailer. The objective concerning evaluation of the equipment was accomplished, but the results were not entirely positive. Significant engineering apparently remains to be done before a reliable system can be fielded. Problems were identified with the trailer to tractor fiber optic connector used for this test. In an over-the-road environment, the communication between the trailer instrumentation and the tractor must be dependable. In addition, the computer in the truck must be able to withstand the rigors of the road. The major objective--data collection and analysis--was also accomplished. Using data collected by instruments on the truck, a ''bad-curve'' database can be generated. Using

  6. [Persistent amphetamine consumption by truck drivers in São Paulo State, Brazil, despite the ban on production, prescription, and use].

    Oliveira, Lúcio Garcia de; Endo, Ligia Goes; Sinagawa, Daniele Mayumi; Yonamine, Maurício; Munoz, Daniel Romero; Leyton, Vilma

    2013-09-01

    Amphetamine use by truck drivers for occupational purposes is widely known. The production and consumption of amphetamines was banned by the Brazilian National Health Surveillance Agency (ANVISA) in October 2011. This study analyzes persistent amphetamine use by truck drivers since the ban was implemented. A convenience sample of 427 truck drivers was taken along highways in São Paulo State in 2012. Participants were asked to answer a structured questionnaire and provide a urine sample to screen for recent amphetamine consumption through toxicological analysis. Among the interviewed drivers, 7% had used some illicit drug recently and 2.7% had used amphetamines. Amphetamines are still consumed by truck drivers despite the risks and the recent ban. The authorities should thus monitor the possession and use of amphetamines by drivers in order to effectively enforce the ban.

  7. Truck Route Choice Modeling using Large Streams of GPS Data

    2017-07-31

    The primary goal of this research was to use large streams of truck-GPS data to analyze travel routes (or paths) chosen by freight trucks to travel between different origin and destination (OD) location pairs in metropolitan regions of Florida. Two s...

  8. Waste Management's LNG Truck Fleet: Final Results

    Chandler, K. [Battelle (US); Norton, P. [National Renewable Energy Laboratory (US); Clark, N. [West Virginia University (US)

    2001-01-25

    Waste Management, Inc., began operating a fleet of heavy-duty LNG refuse trucks at its Washington, Pennsylvania, facility. The objective of the project was to provide transportation professionals with quantitative, unbiased information on the cost, maintenance, operational, and emissions characteristics of LNG as one alternative to conventional diesel for heavy-duty trucking applications.

  9. Optimising Shovel-Truck Fuel Consumption using Stochastic ...

    Optimising the fuel consumption and truck waiting time can result in significant fuel savings. The paper demonstrates that stochastic simulation is an effective tool for optimising the utilisation of fossil-based fuels in mining and related industries. Keywords: Stochastic, Simulation Modelling, Mining, Optimisation, Shovel-Truck ...

  10. 76 FR 56868 - Pilot Project on NAFTA Trucking Provisions

    2011-09-14

    ...-0097] Pilot Project on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... that have applied to participate in the Agency's long- haul pilot program to test and demonstrate the... proceed with the initiation of a U.S.-Mexico cross-border long-haul trucking pilot program to test and...

  11. 77 FR 12356 - Pilot Program on NAFTA Trucking Provisions

    2012-02-29

    ...-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... that applied to participate in the Agency's long-haul pilot program to test and demonstrate the ability... cross-border long-haul trucking pilot program to test and demonstrate the ability of Mexico-domiciled...

  12. 78 FR 25525 - Pilot Program on NAFTA Trucking Provisions

    2013-05-01

    ...-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration..., which applied to participate in the Agency's long-haul pilot program to test and demonstrate the ability... long-haul trucking pilot program to test and demonstrate the ability of Mexico-domiciled motor carriers...

  13. 77 FR 40938 - Pilot Program on NAFTA Trucking Provisions

    2012-07-11

    ...-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... Morales Guevara (DBA Fletes Morales) which applied to participate in the Agency's long-haul pilot program...] its intent to proceed with the initiation of a U.S.-Mexico cross-border long-haul trucking pilot...

  14. 77 FR 27837 - Pilot Program on NAFTA Trucking Provisions

    2012-05-11

    ...-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... carriers that applied to participate in the Agency's long- haul pilot program to test and demonstrate the... intent to proceed with the initiation of a U.S.-Mexico cross-border long-haul trucking pilot program to...

  15. 78 FR 24293 - Pilot Program on NAFTA Trucking Provisions

    2013-04-24

    ...-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... in the Agency's long-haul pilot program to test and demonstrate the ability of Mexico- domiciled... cross-border long-haul trucking pilot program to test and demonstrate the ability of Mexico-domiciled...

  16. 76 FR 56272 - Pilot Project on NAFTA Trucking Provisions

    2011-09-12

    ...-0097] Pilot Project on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... that have applied to participate in the Agency's long- haul pilot program to test and demonstrate the... cross-border long-haul trucking pilot program to test and demonstrate the ability of Mexico-domiciled...

  17. 76 FR 73765 - Pilot Project on NAFTA Trucking Provisions

    2011-11-29

    ...-0097] Pilot Project on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... that have applied to participate in the Agency's long- haul pilot program to test and demonstrate the... proceed with the initiation of a U.S.-Mexico cross-border long-haul trucking pilot program to test and...

  18. design and fabrication of a multipurpose railroad hand truck

    user

    the guide rail was constructed using 50mm by 50mm mild steel angle bar. The hand truck is ... material handling management, a company's operational performance may ... pose a health risk especially where the hand truck has to be used ...

  19. A Cognitive Analysis of Truck Drivers’ Right-hand Turns

    Sieker, Tobias Grønborg; G. Skulason, Thorgeir; Sletting, Kristian

    2015-01-01

    This paper presents an investigation of truck drivers’ performance during right-hand turns performed in intersections with traffic lights in order to elicit the truck drivers’ domain, decision-making processes, and the strategies used while executing the turn. To gain knowledge about this, a truc...

  20. 49 CFR 215.119 - Defective freight car truck.

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Defective freight car truck. 215.119 Section 215... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAILROAD FREIGHT CAR SAFETY STANDARDS Freight Car Components Suspension System § 215.119 Defective freight car truck. A railroad may not place or continue in service a...

  1. Optimising Shovel-Truck Fuel Consumption using Stochastic ...

    Michael

    2017-12-02

    Dec 2, 2017 ... J. Bansah. 1University of Mines and Technology, P. O. Box 237, Tarkwa, Ghana. 2Missouri S&T .... of dump trucks which could be mixed fleets or same fleets. .... another portraying the reality of trucks moving from a shovel to a ...

  2. Activity Recognition and Localization on a Truck Parking Lot

    Andersson, M.; Patino, L.; Burghouts, G.J.; Flizikowski, A.; Evans, M.; Gustafsson, D.; Petersson, H.; Schutte, K.; Ferryman, J.

    2013-01-01

    In this paper we present a set of activity recognition and localization algorithms that together assemble a large amount of information about activities on a parking lot. The aim is to detect and recognize events that may pose a threat to truck drivers and trucks. The algorithms perform zone-based

  3. US long-haul truck driver work organization and the association with cardiometabolic disease risk.

    Hege, Adam; Lemke, Michael Kenneth; Apostolopoulos, Yorghos; Perko, Mike; Sönmez, Sevil; Strack, Robert

    2017-09-03

    Work organization, including long working hours, irregular work schedules, and job stress, has been associated with increased cardiometabolic disease (CMD) risk for numerous working populations. The purpose of this study was to examine the associations between work hours, work schedules, job stress, and CMD risk for a sample of US long-haul truck drivers (LHTDs). A nonexperimental, descriptive, cross-sectional design was employed to collect survey and anthropometric data from 260 US LHTDs at a major truck stop. The mean BMI was 33.40 kg/m 2 and mean waist circumference was 114.77 cm. Using logistic regression, researchers found longer work hours, especially greater than 11 hours daily, were associated with increased odds for an extremely high risk of CMD. Results support comprehensive and integrated approaches that address work organization, and in particular long working hours, to reduce drivers' CMD risk.

  4. Truck Drivers' Experiences and Perspectives Regarding Factors Influencing Traffic Accidents: A Qualitative Study.

    Karimi Moonaghi, Hossein; Ranjbar, Hossein; Heydari, Abbas; Scurlock-Evans, Laura

    2015-08-01

    Traffic accidents are a major public health problem, leading to death and disability. Although pertinent studies have been conducted, little data are available in Iran. This study explored the experiences of truck drivers and their perspectives regarding factors contributing to traffic accidents. Eighteen truck drivers, purposively sampled, participated in semi-structured interviews. Data were analyzed using qualitative content analysis. A main theme, lack of ability to control stress, emerged as a factor influencing the incidence of traffic accidents. This main theme was found to have three subthemes: poor organization of the job, lack of workplace facilities and proper equipment, and unsupportive environment. Although several factors were found to contribute to traffic accidents, their effects were not independent, and all were considered significant. Identifying factors that contribute to traffic accidents requires a systematic and holistic approach. Findings could be used by the transportation industry and community health centers to prevent traffic accidents. © 2015 The Author(s).

  5. Development of offroad unmanned dump truck navigation system. Dump truck mujin soko system no kaihatsu ni tsuite

    Horii, Z [Nittetsu Mining Co. Ltd., Tokyo (Japan)

    1992-08-25

    A large offroad unmanned dump truck navigation system has been developed, and is in practical operation mounted on dump trucks at Torigatayama Limestone Quarry of Nittetsu Mining Company. The system functions in a manual dump truck navigation mode, wireless navigation mode, and unmanned control mode. The unmanned control mode further includes a mode to navigate the truck on a predetermined course with its data having been input in a computer and a mode that when the truck was moved on a course under a wireless control, the computer learns the course and drives the truck autonomously thereafter. The safety measures are divided into the hardware safety function to detect abnormalities in brakes and other vehicle parts, and the software safety functions of data communications, sensor action check, and prevention of collision of trucks with each other. The system has resulted in a productivity of average one-way travel distance of 345 m, and average unmanned navigation cycle time of 9 minutes and 26 seconds for a transportation efficiency of 541 t/hour/truck, having reached at least the manned operation level. 4 figs., 1 tab.

  6. 75 FR 76518 - Volvo Trucks North America and Mack Trucks, Inc., Receipt of Petition for Decision of...

    2010-12-08

    ... manufactured from March 1, 2007 through December 11, 2009. A total of 1,916 affected Volvo trucks were... trucks were manufactured from March 1, 2007, through December 11, 2009. A total 1,287 affected Mack... that their petition, to exempt them from providing recall notification of noncompliance as required by...

  7. 40 CFR 418.21 - Specialized definitions.

    2010-07-01

    ... STANDARDS FERTILIZER MANUFACTURING POINT SOURCE CATEGORY Ammonia Subcategory § 418.21 Specialized... product shall mean the anhydrous ammonia content of the compound manufactured. (c) The term shipping... cleaning tank cars or tank trucks; and discharges from air pollution control scrubbers designed to control...

  8. Contrastación de esquemas de ensayo en carros cesta; Test schemes contrastation in bucket trucks

    José Á Martínez Barbado

    2011-02-01

    Full Text Available La verificación de las condiciones dieléctricas de los dispositivos y equipos utilizados en trabajos conlíneas energizadas resulta vital para la seguridad del personal. Los laboratorios de ensayos especializadosen este campo tienen la responsabilidad de aplicar métodos y procedimientos normalizados o validados,con el fin de obtener resultados confiables. En este trabajo se presentan los resultados de un estudiodonde se aplicó el método de ensayo de medición de la corriente de filtración en carros cesta, empleandodos esquemas diferentes. Los resultados indican diferencias estadísticamente significativas en los valoresde la corriente de filtración entre ambos esquemas para la sección aislante superior y en dos niveles detensión de ensayo. Verification of the dielectric conditions of devices and equipments used in works with energized lines isimportant for the personnel's security. The specialized test laboratories in this field have the responsibilityof applying methods and normalized or validated procedures, with the purpose of obtaining reliable results.In this paper there are presented the results of a study where the test method of the leakage currentmeasurement is applied in bucket trucks, using two different schemes. The results indicate statisticallysignificant differences between both schemes in the leakage current values for the superior boom and twotest voltage levels.

  9. Safety techniques of lightning rod and static electricity in oil tanks and oil trucks

    Ilievska, Tatjana

    1999-01-01

    In this article the ways and examples of lightning rod installation of small tanks for storage of both oil and oil derivates used by petrol stations are presented (an example of some petrol stations in the wider region in Bitola is given ). Also, a lightning rod protection of big tanks and terminals as well as protection of static electricity of tank trucks during transportation of fuel is represented. Special review is given to the protection of static electricity during transforming (decanting) of the fuel. (Author)

  10. Factors Affecting Accidents Risks among Truck Drivers In Egypt

    Elshamly Ahmed Fathalla

    2017-01-01

    Full Text Available Egypt is ranked among the countries with the highest rates of road accidents. According to the American Chamber of Commerce more than 96% of Egypt's goods are transported by trucks and due to their large volume and excessive weight, the severity and number of truck accident fatalities are much higher than other vehicles in Egypt. The present study aims at identifying truck driver's behavior and its influence on crash involvement. Due to the shortage in recording accident data and the inaccurate road accident audit, data was collected from several governorates in Egypt through questionnaire. Questionnaire forms were filled out through personal interviews with truck drivers. The total number of respondents was 643. The final analysis was made on the 615 questionnaires with complete answers. The data was analyzed and logistic regression was applied to accident related data to examine the contributing factors affecting accident occurrence of truck drivers. Results showed that fatigue in terms of driving hours (continuous and total and lack of sleep, drug use during driving, and driver obesity are the most influencing factors on the occurrence of truck accidents in Egypt. The findings of this research highlight the important role human factors have on the risk of crash involvement amongst Egypt's truck drivers and the need to improve their work conditions.

  11. CETA truck and EVA restraint system

    Beals, David C.; Merson, Wayne R.

    1991-01-01

    The Crew Equipment Translation Aid (CETA) experiment is an extravehicular activity (EVA) Space Transportation System (STS) based flight experiment which will explore various modes of transporting astronauts and light equipment for Space Station Freedom (SSF). The basic elements of CETA are: (1) two 25 foot long sections of monorail, which will be EVA assembled in the STS cargo bay to become a single 50 ft. rail called the track; (2) a wheeled baseplate called the truck which rolls along the track and can accept three cart concepts; and (3) the three carts which are designated manual, electric, and mechanical. The three carts serve as the astronaut restraint and locomotive interfaces with the track. The manual cart is powered by the astronaut grasping the track's handrail and pulling himself along. The electric cart is operated by an astronaut turning a generator which powers the electric motor and drives the cart. The mechanical cart is driven by a Bendix type transmission and is similar in concept to a man-propelled railroad cart. During launch and landing, the truck is attached to the deployable track by means of EVA removable restraint bolts and held in position by a system of retractable shims. These shims are positioned on the exterior of the rail for launch and landing and rotate out of the way for the duration of the experiment. The shims are held in position by strips of Velcro nap, which rub against the sides of the shim and exert a tailored force. The amount of force required to rotate the shims was a major EVA concern, along with operational repeatability and extreme temperature effects. The restraint system was tested in a thermal-vac and vibration environment and was shown to meet all of the initial design requirements. Using design inputs from the astronauts who will perform the EVA, CETA evolved through an iterative design process and represented a cooperative effort.

  12. CUSTOMER'S PERCEPTION TOWARDS FOOD TRUCK PRODUCTS IN INDIA

    Dr. Ramakrishna Bandaru*, Prof. H. Venkateshwarlu

    2017-01-01

    Food Truck business is a very famous and a growing business in today’s time. Over the decade, every country in the world has been following the trend of the mobile food business. The silent feature of the food truck business is ‘customer reach and satisfaction’. Along with the increase in people living standards, ‘food on wheel’ business made a popular. According to IBIS World report, the food truck industry in the world has grown an average of 9.3% per year over the last five years. Slowly,...

  13. Projection of light-truck population to year 2025

    1978-10-01

    The recent growth in the number of light trucks is a matter of considerable interest in that it may have far-reaching implications for gasoline consumption. This paper forecasts the number of light trucks in the years to 2025. The forecast is based on economic scenarios developed by SRI International. Except for the case of the most-dismal economic forecast, the number of light trucks is predicted to increase monotonically and to show the greatest rate of increase between 1973 and 1980.

  14. Specialized languages

    Mousten, Birthe; Laursen, Anne Lise

    2016-01-01

    Across different fields of research, one feature is often overlooked: the use of language for specialized purposes (LSP) as a cross-discipline. Mastering cross-disciplinarity is the precondition for communicating detailed results within any field. Researchers in specialized languages work cross...... science fields communicate their findings. With this article, we want to create awareness of the work in this special area of language studies and of the inherent cross-disciplinarity that makes LSP special compared to common-core language. An acknowledgement of the importance of this field both in terms...... of more empirical studies and in terms of a greater application of the results would give language specialists in trade and industry a solid and updated basis for communication and language use....

  15. Electrical Characterization of Special Purpose Linear Microcircuits.

    1980-05-01

    Forced voltage VHS "Hold" step voltage VIH Logic ŕ" input voltage VII, Logic Ŕ" input voltage VIN Input voltage V10 Input offset voltage VIO AW...Op Amp Data Sh t 11-17 2-4 vpical I.F155A Op Amp Data Sh-evt 11-18 25 C Statistical Sumnar , For F155 Series Devices It-35 2-6 -55 C Stat ist ical...This measurement is performed similar to (10), but with Vcc = + 15 VDC, VIH = + 10.4 , and K6 energized. 12. Gain Error Drift (F7SW AT) The unipolar

  16. Countering North Korean Special Purpose Forces

    Krause, Troy

    1999-01-01

    As United States and Republic of Korea forces stand to defend against a DPRK attack, one of the most formidable tasks is how to counter a second front in the Joint Rear Security Area of the Republic of Korea...

  17. Plug-In Hybrid Medium-Duty Truck Demonstration and Evaluation

    Miyasato, Matt [Electric Power Research Institute (EPRI), Palo Alto, CA (United States); Kosowski, Mark [Electric Power Research Institute (EPRI), Palo Alto, CA (United States)

    2015-10-01

    The Plug-In Hybrid Medium-Duty Truck Demonstration and Evaluation Program was sponsored by the United States Department of Energy (DOE) using American Recovery and Reinvestment Act of 2009 (ARRA) funding. The purpose of the program is to develop a path to migrate plug-in hybrid electric vehicle (PHEV) technology to medium-duty vehicles by demonstrating and evaluating vehicles in diverse applications. The program also provided three production-ready PHEV systems—Odyne Systems, Inc. (Odyne) Class 6 to 8 trucks, VIA Motors, Inc. (VIA) half-ton pickup trucks, and VIA three-quarter-ton vans. The vehicles were designed, developed, validated, produced, and deployed. Data were gathered and tests were run to understand the performance improvements, allow cost reductions, and provide future design changes. A smart charging system was developed and produced during the program. The partnerships for funding included the DOE; the California Energy Commission (CEC); the South Coast Air Quality Management District (SCAQMD); the Electric Power Research Institute (EPRI); Odyne; VIA; Southern California Edison; and utility and municipal industry participants. The reference project numbers are DOE FOA-28 award number EE0002549 and SCAQMD contract number 10659.

  18. Light trucks and highway fatalities : the role of network effects.

    2012-12-01

    Light trucks, such as sport utility vehicles (SUVs) : and pickups, impose greater risks of injury and : death on other motorists than do cars, while at the : same time providing their occupants with increased : protection against these risks relative...

  19. Commercial truck platooning demonstration in Texas – level 2 automation.

    2017-08-01

    Through this project, the Texas Department of Transportation (TxDOT) funded the creation of a comprehensive truck platooning demonstration in Texas, serving as a proactive effort in assessing innovative operational strategies to position TxDOT as a l...

  20. The Aerodynamics of Heavy Vehicles III : Trucks, Buses and Trains

    Orellano, Alexander

    2016-01-01

    This volume contains papers presented at the International conference “The Aerodynamics of Heavy Vehicles III: Trucks, Buses and Trains” held in Potsdam, Germany, September 12-17, 2010 by Engineering Conferences International (ECI). Leading scientists and engineers from industry, universities and research laboratories, including truck and high-speed train manufacturers and operators were brought together to discuss computer simulation and experimental techniques to be applied for the design of more efficient trucks, buses and high-speed trains in the future.   This conference was the third in the series after Monterey-Pacific Groove in 2002 and Lake Tahoe in 2007.  The presentations address different aspects of train aerodynamics (cross wind effects, underbody flow, tunnel aerodynamics and aeroacoustics, experimental techniques), truck aerodynamics (drag reduction, flow control, experimental and computational techniques) as well as computational fluid dynamics and bluff body, wake and jet flows.

  1. Market capitalization of the trucking industry sector, 2005

    2006-08-01

    This report focuses on the market valuation of the overall trucking industry sector and each segment within it. In the past, while the focus has been on stock price appreciation or depreciation, this report emphasizes market capitalization returns. S...

  2. Crash risk factors for interstate large trucks in North Carolina.

    Teoh, Eric R; Carter, Daniel L; Smith, Sarah; McCartt, Anne T

    2017-09-01

    Provide an updated examination of risk factors for large truck involvements in crashes resulting in injury or death. A matched case-control study was conducted in North Carolina of large trucks operated by interstate carriers. Cases were defined as trucks involved in crashes resulting in fatal or non-fatal injury, and one control truck was matched on the basis of location, weekday, time of day, and truck type. The matched-pair odds ratio provided an estimate of the effect of various driver, vehicle, or carrier factors. Out-of-service (OOS) brake violations tripled the risk of crashing; any OOS vehicle defect increased crash risk by 362%. Higher historical crash rates (fatal, injury, or all crashes) of the carrier were associated with increased risk of crashing. Operating on a short-haul exemption increased crash risk by 383%. Antilock braking systems reduced crash risk by 65%. All of these results were statistically significant at the 95% confidence level. Other safety technologies also showed estimated benefits, although not statistically significant. With the exception of the finding that short-haul exemption is associated with increased crash risk, results largely bolster what is currently known about large truck crash risk and reinforce current enforcement practices. Results also suggest vehicle safety technologies can be important in lowering crash risk. This means that as safety technology continues to penetrate the fleet, whether from voluntary usage or government mandates, reductions in large truck crashes may be achieved. Practical application: Results imply that increased enforcement and use of crash avoidance technologies can improve the large truck crash problem. Copyright © 2017 National Safety Council and Elsevier Ltd. All rights reserved.

  3. The Aggregate Planning For Trucking Operation in Cikarang Dry Port

    Dwi Puspita Sari Utami

    2015-06-01

    Full Text Available Abstract. Cikarang Dry Port currently is the only dry port in Indonesia. This Dry Port has a role to connect or extend the Sea Port to the industrial areas located far from Sea Port. Thus, it creates a value added and also reduce costs. One of the operations done in Cikarang Dry Port is trucking operation. This research aims to examine the planning of 2014 trucking activity in Cikarang Dry Port to determine the right number of the truck that will be best occupied to manage all demands. The analysis begins with demand forecasting by using a moving average method of 12 months or one year period in 2013 which will be used as main information to develop the plans. There are three plans developed in this research. Based on the three plans, Plan A with minimum trucking plan with subcontracting is the most profitable which gives the highest profitability of Rp. 374,984,625. Recommendation for this research is using the current minimum number of 39 trucks rent with additional subcontracting when the demand is exceeding the capacity, thus, Cikarang Dry Port can occupy all demands and gain more profits. Keywords: Aggregate Planning; Scheduling; Trucking Operation; Moving Average; Cikarang Dry Port

  4. The Aggregate Planning For Trucking Operation in Cikarang Dry Port

    Dwi Puspita Sari Utami

    2015-07-01

    Full Text Available Abstract. Cikarang Dry Port currently is the only dry port in Indonesia. This Dry Port has a role to connect or extend the Sea Port to the industrial areas located far from Sea Port. Thus, it creates a value added and also reduce costs. One of the operations done in Cikarang Dry Port is trucking operation. This research aims to examine the planning of 2014 trucking activity in Cikarang Dry Port to determine the right number of the truck that will be best occupied to manage all demands. The analysis begins with demand forecasting by using a moving average method of 12 months or one year period in 2013 which will be used as main information to develop the plans. There are three plans developed in this research. Based on the three plans, Plan A with minimum trucking plan with subcontracting is the most profitable which gives the highest profitability of Rp. 374,984,625. Recommendation for this research is using the current minimum number of 39 trucks rent with additional subcontracting when the demand is exceeding the capacity, thus, Cikarang Dry Port can occupy all demands and gain more profits.Keywords: Aggregate Planning; Scheduling; Trucking Operation; Moving Average; Cikarang Dry Port

  5. Application of Chaos Theory in Trucks' Overloading Enforcement

    Abbas Mahmoudabadi

    2013-01-01

    Full Text Available Trucks' overloading is considered as one of the most substantial concerns in road transport due to a possible road surface damage, as well as, are less reliable performance of trucks' braking system. Sufficient human resource and adequate time scheduling are to be planned for surveying trucks' overloading; hence, it seems required to prepare an all-around model to be able to predict the number of overloaded vehicles. In the present research work, the concept of chaos theory has been utilized to predict the ratio of trucks which might be guessed overloaded. The largest Lyapunov exponent is utilized to determine the presence of chaos using experimental data and concluded that the ratio of overloaded trucks reflects chaotic behavior. The prediction based on chaos theory is compared with the results of simple smoothing and moving average methods according to the well-known criterion of mean square errors. The results have also revealed that the chaotic prediction model would act more capably comparing the analogous methods including simple smoothing and moving average to predict the ratio of passing trucks to be possibly overloaded.

  6. Prevalence of at-risk drinking among Brazilian truck drivers and its interference on the performance of executive cognitive tasks.

    de Oliveira, Lucio Garcia; Leopoldo, Kae; Gouvea, Marcela Julio Cesar; Barroso, Lucia Pereira; Gouveia, Paula Adriana Rodrigues; Muñoz, Daniel Romero; Leyton, Vilma

    2016-09-01

    Binge drinking (BD) has been associated with an increase in the risk of alcohol-related injuries. Alcohol continues to be the main substance consumed by truck drivers, a population of special concern, since they are often involved in traffic accidents. The aim of this study was to estimate the prevalence of BD and its interference in the executive functioning among truck drivers in Sao Paulo, Brazil. A non-probabilistic sample of 684 truck drivers was requested to answer a structured research instrument on their demographic data and alcohol use. They performed cognitive tests to assess their executive functioning and inventories about confounding variables. The participants were then divided according to their involvement in BD. 17.5% of the interviewees have reported being engaged in BD. Binge drinkers showed a better performance on one test, despite having done so at the expense of more mistakes and lower accuracy. More interestingly, binge drinkers took three seconds longer than non-binge drinkers to inhibit an inadequate response, which is worrisome in the context of traffic. Overall, the deleterious effect of BD on performance remained after controlling for the effects of confounding variables in regression logistic models. As the use of alcohol among truck drivers may be as a way to get by with their work conditions, we believe that a negotiation between their work organization and public authorities would reduce such use, preventing negative interferences on truck drivers' cognitive functioning, which by its turn may also prevent traffic accidents. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  7. MCDA APPLIED TO PERFORMANCE APPRAISAL OF SHORT-HAUL TRUCK DRIVERS: A CASE STUDY IN A PORTUGUESE TRUCKING COMPANY

    Raquel Morte

    2015-03-01

    Full Text Available Performance appraisal increasingly assumes a more important role in any organizational environment. In the trucking industry, drivers are the company's image and for this reason it is important to develop and increase their performance and commitment to the company's goals. This paper aims to create a performance appraisal model for trucking drivers, based on a multi-criteria decision aid methodology. The PROMETHEE and MMASSI methodologies were adapted using the criteria used for performance appraisal by the trucking company studied. The appraisal involved all the truck drivers, their supervisors and the company's Managing Director. The final output is a ranking of the drivers, based on their performance, for each one of the scenarios used. The results are to be used as a decision-making tool to allocate drivers to the domestic haul service.

  8. Liquefied Natural Gas for Trucks and Buses

    James Wegrzyn; Michael Gurevich

    2000-01-01

    Liquefied natural gas (LNG) is being developed as a heavy vehicle fuel. The reason for developing LNG is to reduce our dependency on imported oil by eliminating technical and costs barriers associated with its usage. The U.S. Department of Energy (DOE) has a program, currently in its third year, to develop and advance cost-effective technologies for operating and refueling natural gas-fueled heavy vehicles (Class 7-8 trucks). The objectives of the DOE Natural Gas Vehicle Systems Program are to achieve market penetration by reducing vehicle conversion and fuel costs, to increase consumer acceptance by improving the reliability and efficiency, and to improve air quality by reducing tailpipe emissions. One way to reduce fuel costs is to develop new supplies of cheap natural gas. Significant progress is being made towards developing more energy-efficient, low-cost, small-scale natural gas liquefiers for exploiting alternative sources of natural gas such as from landfill and remote gas sites. In particular, the DOE program provides funds for research and development in the areas of; natural gas clean up, LNG production, advanced vehicle onboard storage tanks, improved fuel delivery systems and LNG market strategies. In general, the program seeks to integrate the individual components being developed into complete systems, and then demonstrate the technology to establish technical and economic feasibility. The paper also reviews the importance of cryogenics in designing LNG fuel delivery systems

  9. Truck accident involving unirradiated nuclear fuel

    Carlson, R.W.; Fischer, L.E.

    1992-07-01

    In the early morning of Dec. 16, 1991, a severe accident occurred when a passenger vehicle traveling in the wrong direction collided with a tractor trailer carrying 24 nuclear fuel assemblies in 12 containers on Interstate 1-91 in Springfield, Massachusetts. This paper documents the mechanical circumstances of the accident and the physical environment to which the containers were exposed and the response of the containers and their contents. The accident involved four impacts where the truck was struck by the car, impacted on the center guardrail, impacted on the outer concrete barrier and came to rest against the center guardrail. The impacts were followed by a fire that began in the engine compartment, spread to the.tractor and cab, and eventually spread to the trailer and payload. The fire lasted for about three hours and the packages were involved in the fire for about two hours. As a result of the fire, the tractor-trailer was completely destroyed and the packages were exposed to flames with temperatures between 1300 degrees F and 1800 degrees F. The fuel assemblies remained intact during the accident and there was no release of any radioactive material during the accident. This was a very severe accident; however, the injuries were minor and at no time was the public health and safety at risk

  10. Truck accident involving unirradiated nuclear fuel

    Carlson, R.W.; Fischer, L.E.

    1993-01-01

    In the early morning of Dec. 16, 1991, a severe accident occurred when a passenger vehicle traveling in the wrong direction collided with a tractor trailer carrying 24 unirradiated nuclear fuel assemblies in 12 containers on Interstate I-91 in Springfield, Massachusetts. This paper documents the mechanical circumstances of the accident and assesses the physical environment to which the containers were exposed and the response of the containers and their contents. The accident involved four impacts where the truck was struck by the car, impacted on the center guardrail, impacted on the outer concrete barrier and came to rest against the center guardrail. The impacts were followed by a fire that began in the engine compartment, spread to the tractor and cab, and eventually spread to the trailer and payload. The fire lasted for about three hours and the packages were involved in the fire for about two hours. As a result of the fire, the tractor-trailer was completely destroyed and the packages were exposed to flames with temperatures between 1,300 F and 1,800 F. The fuel assemblies remained intact during the accident and there was no release of any radioactive material during the accident. This was a very severe accident; however, the injuries were minor and at no time was the public health and safety at risk

  11. Sizing stack and battery of a fuel cell hybrid distribution truck

    Tazelaar, E.; Shen, Y.; Veenhuizen, P.A.; Hofman, T.; Bosch, van den, P.P.J.

    2012-01-01

    An existing fuel cell hybrid distribution truck, built for demonstration purposes, is used as a case study to investigate the effect of stack (kW) and battery (kW, kWh) sizes on the hydrogen consumption of the vehicle. Three driving cycles, the NEDC for Low Power vehicles, CSC and JE05 cycle, define the driving requirements for the vehicle. The Equivalent Consumption Minimization Strategy (ECMS) is used for determining the control setpoint for the fuel cell and battery system. It closely appr...

  12. Podnikatelský plán Boy´s Burger Food Truck

    Kábelová, Zuzana

    2015-01-01

    The main goal of this Master thesis is to verify the viability of the food truck with fast food. This type of business is well-known in the United States of America. The purpose is to find out whether the firm will be profitable and sufficiently attractive to customers in chosen market. This Master thesis is divided into theoretical and practical part. The theoretical part describes the business models and current tips for business plan and starting the business. Next there is made a list of ...

  13. Joint purpose?

    Pristed Nielsen, Helene

    2013-01-01

    Starting from Crenshaw´s point that antiracism often fails to interrogate patriarchy and that feminism often reproduces racist practices (1991: 1252), this paper asks: What are the theoretical reasons for believing that feminism and anti-racism can be regarded as fighting for the joint purpose...

  14. Demonstration of fleet trucks fueled with PV hydrogen

    Provenzano, J.; Scott, P.B.; Zweig, R.

    1998-01-01

    The Clean Air Now (CAN) Solar Hydrogen Project has been installed at the Xerox Corporation, El Segundo, California site. Three Ford Ranger trucks have been converted to use hydrogen fuel. The ''stand- alone'' electrolyzer and hydrogen dispensing system is powered by a photovoltaic array with no connection to the power grid. A variable frequency DC/AC converter steps up the voltage to drive the 15 hp motor for the hydrogen compressor. Up to 400 standard cubic meters (SCM) of solar hydrogen is stored, and storage of up to 2300 SCM of commercial hydrogen is collocated. As the hydrogen storage is within 5km of Los Angeles International Airport, pilot operation of a hydrogen fuel cell bus for airport shuttle service has been demonstrated with fueling at the CAN facility. The truck engine conversions are bored to 2.91 displacement, use a Roots type supercharger and CVI (constant volume injection) fuel induction to allow performance similar to that of the gasoline powered truck. Truck fuel storage is done with carbon composite tanks at pressures up to 24.8 MPa (3600 psi). Two tanks are located just behind the driver's cab, and take up nearly half of the truck bed space. The truck highway range is approximately 140 miles. The engine operates in lean burn mode, with nil emissions of CO and HC. NO x emissions vary with load and rpm in the range from 10 to 100 ppm, yielding total emissions at a small fraction of the ULEV standard. Two Xerox fleet trucks have been converted, and one for the City of West Hollywood. The Clean Air Now Program demonstrates that hydrogen powered fleet development is an appropriate safe, and effective strategy for improvement of urban air quality. It further demonstrates that continued technological development and cost reduction will make such implementation competitive. (Author)

  15. Surrogate fuel assembly multi-axis shaker tests to simulate normal conditions of rail and truck transport

    McConnell, Paul E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Koenig, Greg John [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Uncapher, William Leonard [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Grey, Carissa [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Engelhardt, Charles [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Saltzstein, Sylvia J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sorenson, Ken B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-05-01

    This report describes the third set of tests (the “DCLa shaker tests”) of an instrumented surrogate PWR fuel assembly. The purpose of this set of tests was to measure strains and accelerations on Zircaloy-4 fuel rods when the PWR assembly was subjected to rail and truck loadings simulating normal conditions of transport when affixed to a multi-axis shaker. This is the first set of tests of the assembly simulating rail normal conditions of transport.

  16. Surrogate fuel assembly multi-axis shaker tests to simulate normal conditions of rail and truck transport

    McConnell, Paul E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Koenig, Greg John [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Uncapher, William Leonard [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Grey, Carissa [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Engelhardt, Charles [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Saltzstein, Sylvia J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sorenson, Ken B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-05-12

    This report describes the third set of tests (the “DCLa shaker tests”) of an instrumented surrogate PWR fuel assembly. The purpose of this set of tests was to measure strains and accelerations on Zircaloy-4 fuel rods when the PWR assembly was subjected to rail and truck loadings simulating normal conditions of transport when affixed to a multi-axis shaker. This is the first set of tests of the assembly simulating rail normal conditions of transport.

  17. Experimental Measurement of the Flow Field of Heavy Trucks

    Fred Browand; Charles Radovich

    2005-05-31

    Flat flaps that enclose the trailer base on the sides and top are known to reduce truck drag and reduce fuel consumption. Such flapped-truck geometries have been studied in laboratory wind tunnels and in field tests. A recent review of wind tunnel data for a variety of truck geometries and flow Reynolds numbers show roughly similar values of peak drag reduction, but differ in the determination of the optimum flap angle. Optimum angles lie in the range 12 degrees-20 degrees, and may be sensitive to Reynolds number and truck geometry. The present field test is undertaken to provide additional estimates of the magnitude of the savings to be expected on a typical truck for five flap angles 10, 13, 16, 19, and 22 degrees. The flaps are constructed from a fiberglass-epoxy-matrix material and are one-quarter of the base width in length (about 61 cm, or 2 feet). They are attached along the rear door hinge lines on either side of the trailer, so that no gap appears at the joint between the flap and the side of the trailer The flap angle is adjusted by means of two aluminum supports. The present test is performed on the NASA Crows Landing Flight Facility at the northern end of the San Joaquin valley in California. The main runway is approximately 2400 meters in length, and is aligned approximately in a north-south direction The test procedure is to make a series of runs starting at either end of the runway. All runs are initiated under computer control to accelerate the truck to a target speed of 60 mph (96 6 km/hr), to proceed at the target speed for a fixed distance, and to decelerate at the far end of the runway. During a run, the broadcast fuel rate, the engine rpm, forward speed, elapsed time--as well as several other parameters (10 in all)--are digitized at a rate of 100 digitizations per second. Various flapped-conditions are interspersed with the ''no flaps'' control, and are sequenced in a different order on different days. Approximately 310 runs

  18. Measuring Timber Truck Loads With Image Processing In Paper Mills

    Silva, M. Santos; Carvalho, Fernando D.; Rodrigues, F. Carvalho; Goncalves, Ana N. R.

    1989-04-01

    The raw material for the paper industry is wood. To have an exact account of the stock of piled sawn tree trunks every truck load entering the plant's stockyard must be measured as to the amount of wood being brought in. Weighting down the trucks has its own problems, mainly, due to the high capacity of the tree trunks to absorb water. This problem is further enhanced when calculations must be made to arrive at the mass of sawn tree trunks which must go into the process of producing a certain quantity of paper pulp. The method presented here is based on two fixed cameras which take the image of the truck load. One takes a view of the trunks in order to get information on the average length of the tree trunks. The other obtains a side view which is digitised and by just discriminating against a grey level the area covered by the tree trunk cross section is measured. A simple arithmetic operation gives the volume of wood in the trunk. The same computer, a PC, will register the trucks particulars is almost independent of weather the wood is wet or dry and it serves trucks of any size.

  19. Long-Run Diversion Effects of Changes in Truck Size and Weight (TS&W) Restrictions: An Update of the 1980 Friedlaender Spady Analysis

    McCullough, Gerard J.

    2013-01-01

    The purpose of this analysis is to estimate the effect that revised truck size and weight (TS&W) restrictions would have on competitive rail-truck markets in the United States. The analysis is based on a classic study of the intercity freight markets that Ann Friedlaender and Richard Spady (FS) published in the Review of Economics and Statistics in 1980.1 The FS study provided a macro-level perspective on the freight markets by focusing on transportation decisions in key industrial sectors—fo...

  20. Supplying of Assembly Lines Using Train of Trucks

    Čujan, Zdeněk; Fedorko, Gabriel

    2016-11-01

    The typical supply system conceptions, i.e. the concepts "Just-in-time" (JIT) and "Just-in-sequence" (JIS) are very important factors with regard to a fluent operation of the assembly lines. Therefore the contemporary intra plant transport systems are being replaced by a new kind of the transportation technology, namely by means of the trains of trucks. The trains of trucks are used in two possible operational modes: either with a driver or without driver (fully automated). The trucks of the logistic trains are also cheaper and they are able to carry a larger volume and mass of the material at once. There are reduced in this way not only the investment costs, but also the operational expenses.

  1. Safety climate and the distracted driving experiences of truck drivers.

    Swedler, David I; Pollack, Keshia M; Agnew, Jacqueline

    2015-07-01

    For truck drivers, distracted driving is a workplace behavior that increases occupational injury risk. We propose safety climate as an appropriate lens through which researchers can examine occupational distracted driving. Using a mixed methods study design, we surveyed truck drivers using the Safety Climate Questionnaire (SCQ) complemented by semi-structured interviews of experts on distracted driving and truck safety. Safety climate was assessed by using the entire SCQ as an overall climate score, followed by factor analysis that identified the following safety climate factors: Communications and Procedures; Management Commitment; and Work Pressure. In multivariate regression, the overall safety climate scale was associated with having ever experienced a crash and/or distraction-involved swerving. Interview participants described how these SCQ constructs could affect occupational distracted driving. To reduce distraction-related crashes in their organizations, management can adhere to safe policies and procedures, invest in engineering controls, and develop safer communication procedures. © 2015 Wiley Periodicals, Inc.

  2. Could Expanded Freight Rail Reduce Air Pollution from Trucks?

    Bickford, E. E.; Holloway, T.; Johnston, M.

    2010-12-01

    Cars, trucks and trains are a significant source of emissions that impact both climate and air quality on regional to global scales. Diesel vehicles, most used for freight transport, account for 42% of on-road nitrogen oxide emissions, 58% of on-road fine particulate emissions, and 21% of on-road carbon dioxide emissions. With freight tonnage projected to increase 28% by 2018, and freight trucks the fastest growing source of transportation emissions, we evaluate the potential for increased rail capacity to reduce the environmental impacts of trucks. Most widely available mobile source emissions inventories contain insufficient spatial detail to quantify realistic emission scenario options, and none to date have been linked with commodity flow information in a manner appropriate to consider the true potential of rail substitution. To support a truck-to-rail analysis, and other policy assessments requiring roadway-by-roadway analysis, we have developed a freight emissions inventory for the Upper Midwest based on the Federal Highway Administration’s Freight Analysis Framework version 2.2 and the Environmental Protection Agency’s on-road emissions model, Mobile6.2. Using a Geographical Information System (GIS), we developed emissions scenarios for truck-to-rail modal shifts where 95% of freight tonnage on trips longer than 400 miles is shifted off of trucks and onto railways. Scenarios will be analyzed with the Community Multiscale Air Quality (CMAQ) regional model to assess air quality impacts of associated changes. By using well-respected transportation data and realistic assumptions, results from this study have the potential to inform decisions on transportation sustainability, carbon management, public health, and air quality.

  3. Heavy truck modeling for fuel consumption. Simulations and measurements

    Sandberg, T.

    2001-12-01

    Fuel consumption for heavy trucks depends on many factors like roads, weather, and driver behavior that are hard for a manufacturer to influence. However, one design possibility is the power train configuration. Here a new simulation program for heavy trucks is created to find the configuration of the power train that gives the lowest fuel consumption for each transport task. For efficient simulations the model uses production code for speed and gear control, and it uses exchangeable data sets to allow simulation of the whole production range of engine types, on recorded road profiles from all over the world. Combined with a graphical user interface this application is called STARS (Scania Truck And Road Simulation). The forces of rolling resistance and air resistance in the model are validated through an experiment where the propeller shaft torque of a heavy truck is measured. It is found that the coefficient of rolling resistance is strongly dependent on tire temperature, not only on vehicle speed as expected. This led to the development of a new model for rolling resistance. The model includes the dynamic behavior of the tires and relates rolling resistance to tire temperature and vehicle speed. In another experiment the fuel consumption of a test truck in highway driving is measured. The altitude of the road is recorded with a barometer and used in the corresponding simulations. Despite of the limited accuracy of this equipment the simulation program manage to predict a level of fuel consumption only 2% lower than the real measurements. It is concluded that STARS is a good tool for predicting fuel consumption for trucks in highway driving and for comparing different power train configurations.

  4. Roadmap and technical white papers for the 21st century truck partnership

    None, None

    2006-12-01

    21st Century Truck Partnership will support the development and implementation of technologies that will cut fuel use and emissions and enhance safety, affordability, and performance of trucks and buses.

  5. Contributions of Diesel Truck Emissions to Indoor Elemental Carbon Concentrations in Home Proximate to Ambassador Bridge

    Ambassador Bridge, connecting Detroit, Michigan and Windsor, Ontario, is the busiest international commercial vehicle crossing in North America, with a large percentage of heavy duty diesel trucks. This study seeks to examine the contribution of diesel truck traffic across Ambass...

  6. 27 CFR 24.229 - Tank car and tank truck requirements.

    2010-04-01

    ... BUREAU, DEPARTMENT OF THE TREASURY LIQUORS WINE Spirits § 24.229 Tank car and tank truck requirements. Railroad tank cars and tank trucks used to transport spirits for use in wine production will be constructed...

  7. Estimation and analysis of multifactor productivity in truck transportation : 1987 - 2003

    2009-02-01

    The analysis has three objectives: 1) to estimate multifactor : productivity (MFP) in truck transportation during : 1987-2003; 2) to examine changes in multifactor productivity : in U.S. truck transportation, over time, and : to compare these changes...

  8. Managing truck arrivals with time windows to alleviate gate congestion at container terminals

    Chen, G.; Govindan, Kannan; Yang, Z.

    2013-01-01

    Long truck queues at gates often limit the efficiency of a container terminal and generate serious air pollution. To reduce the gate congestion, this paper proposes a method called'vessel dependent time windows (VDTWs)' to control truck arrivals, which involves partitioning truck entries into gro......Long truck queues at gates often limit the efficiency of a container terminal and generate serious air pollution. To reduce the gate congestion, this paper proposes a method called'vessel dependent time windows (VDTWs)' to control truck arrivals, which involves partitioning truck entries...... into groups and assigning different time windows to the groups. The proposed VDTWs method includes three steps: (1) predicting truck arrivals based on the time window assignment, (2) estimating the queue length of trucks, and (3) optimizing the arrangement of time windows to minimize the total cost...

  9. Factors affecting driver alertness during the operation of haul trucks in the South African mining industry

    Schutte, PC

    2003-06-01

    Full Text Available In view of the seriousness of haul trucks accidents, SIMRAC initiated research to identify factors affecting haul truck driver alertness during mining operations. The information obtained during the risk analysis was used to identify possible...

  10. 76 FR 59166 - Navistar Truck Development and Technology Center, a Subsidiary of Navistar International...

    2011-09-23

    ... Development and Technology Center, a Subsidiary of Navistar International Corporation Truck Division, Fort... International Corporation, Truck Division, Fort Wayne, Indiana (subject firm). The negative determination was... is a headcount reduction across the nation, made possible by the Global Outsourcing. * * * '' The...

  11. Optimization of Front Axle Suspension System of Articulated Dump Truck

    Langer, Thomas Heegaard; Christensen, Brian B.; Mouritsen, Ole Ø.

    2010-01-01

    that has been subjected to comfort improvement is a two axle articulated dump truck. The comfort has been in terms of whole body vibration exposure and the overall improvement has been made possible by adding front axle suspension. However, a hydraulic stabilizing system between the tractor and trailer...... to evaluate the whole body vibrations. By use of a multibody simulation model of the dump truck the whole body vibration exposure has been computed using the predefined work cycle as model input. The design parameters comprise the components of the hydraulic subsystem of the suspension, i.e., the size...

  12. Customer expectations and current offers from food trucks in Helsinki

    Nguyen, An

    2017-01-01

    The aim of this thesis is to determine whether there is a gap between what customers expect and what the food trucks in Helsinki offers in term of diversity of products, price, time and location of service. Do the current offers match with what customers would like to have? The food truck concept has a long history and since 2008 became an international phenomenon. However, it is still relatively young in Helsinki. There are concerted efforts from different parties included the city’s au...

  13. Disruption management for truck appointment system at a container terminal

    Li, N.; Chen, Gang; Jin, Z.

    2016-01-01

    -appointed arrivals at a container terminal that is running an appointment system. Second, we propose some response strategies to cope with different levels of disruptions, and evaluate their resilience ability with two Key Performance Indicators (KPIs): total waiting time of on-time trucks and total idling emissions...... of all trucks, in order to balance the service quality to punctual arrivals and green performance of the whole system. Third, we conduct a sensitivity analysis using a discrete event simulation to understand the performance of the proposed strategies. Considering both KPIs, the best strategy in most......-crane moving distance, especially when the first KPI is given lower weight than the second one....

  14. Impact of Platon ETC system on intercity trucking cost

    Pogotovkina Natalya

    2017-01-01

    Full Text Available In 2015 Platon ETC System, a system of charging trucks with gross vehicle weight exceeding 12 tons, was implemented in Russia. The payment is collected as a compensation fo0 the damage caused to the federal public roads. Platon system is an additional source of financing for the road sector. However, its implementation made the carriers face the increasing costs. This paper presents the first results of the system functioning and the problems, associated with it. We consider the foreign systems of truck charging. The results of calculations, which show the effect of the toll collection on the prime cost of road freight transportation, are also presented.

  15. Real-time pedestrian detection in a Truck's blind spot camera

    Van Beeck, Kristof; Goedemé, Toon

    2014-01-01

    In this paper we present a multi-pedestrian detection and tracking framework targeting a specific application: detecting vulnerable road users in a truck's blind spot zone. Research indicates that existing non-vision based safety solutions are not able to handle this problem completely. Therefore we aim to develop an active safety system which warns the truck driver if pedestrians are present in the truck's blind spot zone. Our system solely uses the vision input from the truck's blind spot c...

  16. Use of illicit drugs by truck drivers arriving at Paranaguá port terminal, Brazil.

    Peixe, Tiago Severo; de Almeida, Rafael Menck; Girotto, Edmarlon; de Andrade, Selma Maffei; Mesas, Arthur Eumann

    2014-01-01

    The purpose of this study was to estimate the prevalence of recent use of illicit drugs among truck drivers who had parked their vehicles at the terminal port in Paranaguá City at Paraná State, southern Brazil. This cross-sectional study was part of a larger research project conducted among drivers at a regional Brazilian port. Data on professional characteristics, involvement in road traffic injuries, sleep, and use of alcohol and illicit drugs were collected using a questionnaire. Urine samples were collected and analyzed for amphetamines, cocaine, and cannabis using gas chromatography with mass spectrometric detection. Sixty-two drivers were included in the study. Toxicological analyses showed that 8.1 percent (95% confidence interval [CI], 2.7-17.8%) of the urine samples were positive for drugs (4.8% for cocaine, 1.6% for amphetamine, and 1.6% for both); 8.1 percent reported drug use during the preceding 30 days in the questionnaire and only one tested positive for the drug in the urine sample. No sample was positive for cannabinoids. In total, at least 14.5 percent (95% CI, 6.9-25.8%) had used illicit drugs during the preceding 30 days based on self-reports and urine testing. Drivers who reported involvement in traffic injuries the year before more often tested positive for drugs in biological samples (P illicit stimulants was common among professional truck drivers transporting grain loads. Thus, actions are needed to reduce drug use among truck drivers in order to prevent drug-related road traffic injuries.

  17. Planning of Truck Platoons: a Literature Review and Directions for Future Research

    A. Kishore Bhoopalam (Anirudh); N.A.H. Agatz (Niels); R.A. Zuidwijk (Rob)

    2017-01-01

    textabstractA truck platoon is a set of virtually linked trucks that drive closely behind one another using automated driving technology. Benefits of truck platooning include cost savings, reduced emissions, and more efficient utilization of road capacity. To fully reap these benefits in the initial

  18. Effects of Variation in Truck Factor on Pavement Performance in Pakistan

    Rabia Chaudry

    2013-01-01

    Full Text Available Seasonal variation coupled with heavy axle loading is the key factor in rapid road deterioration in Pakistan. The serviceability loss is further accelerated by the fact that truck drivers and owners consider overloading as a profitable practice unaware of the adverse effects of this practice. Weigh-in-motion data from two stations located between two major cities of Pakistan (Peshawar and Rawalpindi on Grand Trunk Road (N-5 were collected and analyzed. Analysis of variance and comparison of actual and designed truck factor were performed to identify the most damaging axle truck type. It was found that axle truck type 3 (single/tandem axle is most damaging among all truck types. The actual truck factor for axle truck type 3 is 6.4 times greater than design truck factor. Regression expressions of different forms were also investigated to determine the relationship between truck factor and gross vehicular weight for the specified truck types. An optimum generalization strategy was used to prevent over-generalization and ensure accuracy. For data analysis, 75% of data was used to develop regression models and remaining 25% was to validate those models. The results show that the polynomial expressions performed best and provide a robust relationship that can be employed by the highway authorities to estimate truck factor from gross vehicular weight with a high degree of confidence. It was also observed that damaging effect of various types of trucks was very severe and quite high.

  19. 75 FR 56651 - ITS Joint Program Office; Trucking Industry Mobility & Technology Coalition Annual Meeting

    2010-09-16

    ... DEPARTMENT OF TRANSPORTATION ITS Joint Program Office; Trucking Industry Mobility & Technology... Transportation. ACTION: Notice. The Trucking Industry Mobility & Technology Coalition (TIMTC) Annual [[Page 56652...: Beating Gridlock with a Smart Grid; U.S. DOT Truck Technology Initiatives; and State and Federal...

  20. Scheduling Trucks in a Cross-Dock with Mixed Service Mode Dock Doors

    Bodnar, Peter; Azadeh, Kaveh; Koster, René de

    2017-01-01

    The problem considered in this paper is how to schedule inbound and outbound trucks subject to time windows at a multidoor cross-dock. Dock doors can either be dedicated to inbound or outbound trucks or be capable of handling both truck types. In addition, loads are allowed to be temporarily...

  1. 49 CFR 230.100 - Defects in tender truck axles and journals.

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Defects in tender truck axles and journals. 230... Steam Locomotives and Tenders Running Gear § 230.100 Defects in tender truck axles and journals. (a... wheel seats that is more than 1/8 of an inch in depth. (b) Tender truck journal condemning defects...

  2. Experiences from the exercise ''MERLIN'' for the detection of radioactive substances with the participation of special-purpose vehicles; Erfahrungen aus der Uebung ''MERLIN'' zur Detektion radioaktiver Stoffe unter Beteiligung verschiedenen Einsatzfahrzeuge

    Griesbach, M. [Hessisches Ministerium des Innern und fuer Sport, Wiesbaden (Germany)

    2009-08-15

    Experiences of an exercise with hazardous goods, in particular with radioactive substances (measurements and taking environmental samples) are described. Several special-purpose vehicles with equipment and specially trained crews were used together with radiation protection experts according to the concept of Hesse. It has been the greatest exercise in Hesse with regard to hazardous goods and in particular with regard to ''incidents with radioactive substances''. (orig.)

  3. Design and Validation Testing of TruckScan to Assay Large Sacks of Fukushima Radioactive Debris on a Truck

    Suzuki, Atsuo [Canberra-Japan (Japan); Bronson, Frazier [Canberra Industries Inc. (United States)

    2015-07-01

    As a result of the March 2011 earthquake and resulting tsunami in Japan, there was a serious accident at the Fukushima Dai-ichi Nuclear Power Plant. This accident has contaminated soil and vegetation in a wide area around the plant. Decontamination projects over the last 4 years have resulted in large numbers of 1 cubic meter canvas bags of debris, commonly called Super Sacks [SS]. These are currently stored nearby where they were generated, but starting in 2015, they will be moved to various Interim Storage Facilities [ISF]. Trucks will typically carry 8-20 of these SSs. When the trucks arrive at the ISF they need to be rapidly sorted into groups according to radioactivity level, for efficient subsequent processing. Canberra Industries, Inc. [CI] has designed a new truck monitoring system 'TruckScan' for use at these ISFs. The TruckScan system must measure the entire truck loaded with multiple closely packed SSs, and generate a nuclide specific assay report showing the radioactivity in each individual SS. The Canberra-Japan office, along with Obayashi Corporation have performed validation testing to demonstrate to the regulatory authorities that the proposed technique was sufficiently accurate. These validation tests were conducted at a temporary storage area in Fukushima prefecture. Decontaminated waste of various representative types and of various levels of radioactivity was gathered and mixed to create homogeneous volumes. These volumes were sampled multiple times and assayed with laboratory HPGe detectors to determine the reference concentration of each pile. Multiple SSs were loaded from each pile. Some of the SSs were filled 50% full, others 75% full, and others 100% full, to represent the typical loading configuration of the existing SSs in the field. The content of the SSs are either sand, soil, or vegetation with densities ranging from 0.3 g/cc - 1.6 g/cc. These SSs with known concentrations of Cs-134 and Cs-137 were then loaded onto trucks in

  4. Design and Validation Testing of TruckScan to Assay Large Sacks of Fukushima Radioactive Debris on a Truck

    Suzuki, Atsuo; Bronson, Frazier

    2015-01-01

    As a result of the March 2011 earthquake and resulting tsunami in Japan, there was a serious accident at the Fukushima Dai-ichi Nuclear Power Plant. This accident has contaminated soil and vegetation in a wide area around the plant. Decontamination projects over the last 4 years have resulted in large numbers of 1 cubic meter canvas bags of debris, commonly called Super Sacks [SS]. These are currently stored nearby where they were generated, but starting in 2015, they will be moved to various Interim Storage Facilities [ISF]. Trucks will typically carry 8-20 of these SSs. When the trucks arrive at the ISF they need to be rapidly sorted into groups according to radioactivity level, for efficient subsequent processing. Canberra Industries, Inc. [CI] has designed a new truck monitoring system 'TruckScan' for use at these ISFs. The TruckScan system must measure the entire truck loaded with multiple closely packed SSs, and generate a nuclide specific assay report showing the radioactivity in each individual SS. The Canberra-Japan office, along with Obayashi Corporation have performed validation testing to demonstrate to the regulatory authorities that the proposed technique was sufficiently accurate. These validation tests were conducted at a temporary storage area in Fukushima prefecture. Decontaminated waste of various representative types and of various levels of radioactivity was gathered and mixed to create homogeneous volumes. These volumes were sampled multiple times and assayed with laboratory HPGe detectors to determine the reference concentration of each pile. Multiple SSs were loaded from each pile. Some of the SSs were filled 50% full, others 75% full, and others 100% full, to represent the typical loading configuration of the existing SSs in the field. The content of the SSs are either sand, soil, or vegetation with densities ranging from 0.3 g/cc - 1.6 g/cc. These SSs with known concentrations of Cs-134 and Cs-137 were then loaded onto trucks in

  5. Induction Machine with Improved Operating Performances for Electric Trucks. A FEM-Based Analysis

    MUNTEANU, A.

    2010-05-01

    Full Text Available The paper presents a study concerning the performance developed by induction motors destined for motorization of heavy electric vehicles such as trucks. Taking into consideration the imposed restrictions, one presents, in a comparative manner, the main geometrical parameters which come of the classical design algorithms. A special attention is dedicated to the winding design, since it has to ensure two synchronous speeds corresponding to 16 and 8 poles, respectively. Moreover, the influence of the rotor slots shape for the improvement of the start-up is analyzed. Finally, a FEM-based study (approach based on finite element method is performed to put in view specific torque and slip values such as rated, start-up and pull-out ones.

  6. Analysis of frame structure of medium and small truck crane

    Cao, Fuyi; Li, Jinlong; Cui, Mengkai

    2018-03-01

    Truck crane is an important part of hoisting machinery. Frame, as the support component of the quality of truck crane, determines the safety of crane jib load and the rationality of structural design. In this paper, the truck crane frame is a box structure, the three-dimensional model is established in CATIA software, and imported into Hyperworks software for finite element analysis. On the base of doing constraints and loads for the finite element model of the frame, the finite element static analysis is carried out. And the static stress test verifies whether the finite element model and the frame structure design are reasonable; then the free modal analysis of the frame and the analysis of the first 8 - order modal vibration deformation are carried out. The analysis results show that the maximum stress value of the frame is greater than the yield limit value of the material, and the low-order modal value is close to the excitation frequency value, which needs to be improved to provide theoretical reference for the structural design of the truck crane frame.

  7. SVOC emissions from diesel trucks operating on biodiesel fuels

    This study measured semivolatile organic compounds (SVOCs) in particle matter (PM) emitted from three heavy-duty trucks equipped with modern after-treatment technologies. Emissions testing was conducted as described by the George et al. VOC study also presented as part of this se...

  8. TITAN Legal Weight Truck cask preliminary design report

    1990-04-01

    The Preliminary Design of the TITAN Legal Weight Truck (LWT) Cask System and Ancillary Equipment is presented in this document. The scope of the document includes the LWT cask with fuel baskets; impact limiters, and lifting and tiedown features; the cask support system for transportation; intermodal transfer skid; personnel barrier; and cask lifting yoke assembly. 75 figs., 48 tabs

  9. Haulage Truck Operator. Open Pit Mining Job Training Series.

    British Columbia Dept. of Education, Victoria.

    This training outline for haulage truck operators, one in a series of eight outlines, is designed primarily for company training foremen or supervisors and for trainers to use as an industry-wide guideline for heavy equipment operator training in open pit mining in British Columbia. Intended as a guide for preparation of lesson plans both for…

  10. 78 FR 26106 - Pilot Program on NAFTA Trucking Provisions

    2013-05-03

    ... DEPARTMENT OF TRANSPORTATION Federal Motor Carrier Safety Administration [Docket No FMCSA-2011-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration (FMCSA). ACTION: Notice; correction. SUMMARY: The FMCSA published a document in the Federal Register of...

  11. Model development for air conditioning system in heavy duty trucks

    Kessels, J.T.B.A.; van den Bosch, P.P.J.; Zhang, Quansheng; Li, Shengbo Eben; Deng, Kun

    2016-01-01

    This chapter presents a modelling approach for the air conditioning (AC) system in heavy duty trucks. The presented model entails two major elements: a mechanical compressor model and a thermal AC model. The compressor model describes the massflow of the refrigerant as well as the mechanical power

  12. Presenting a conceptual pattern of HSE performance of oil trucks.

    Ghaleh, Sahar; Omidvari, Manouchehr; Nassiri, Parvin; Momeni, Mansour; Lavasani, Seyed Mohammadreza Miri

    2018-01-25

    Accidents are among the main problems in the oil product supply chain. The most important effective factors in these events are the kind of trucks used and their health, safety, and environment (HSE) condition. The aim of this study was to present a conceptual pattern of the HSE performance of oil trucks in oil industries. In this study, 20 truck models (with fixed tanks), in use over different periods of time, were investigated. In this regard, the criteria and sub-criteria were first determined in two parts-carrier and tank-and weighted by fuzzy analytical hierarchy process (FAHP). The results showed that the most important sub-criteria regarding the HSE factors of the carrier were resistance and strength of the front and rear shields, the brake system, and the ventilation system. The most important sub-criteria regarding the HSE factors of the tank were tank shell thickness and a good tank design shape with respect to portable material. It should be noted that the weight of the criteria with each other and sub-criteria with each other are not equal. This issue is important for decision-making. The main reason for the use of trucks with the lowest score in developing countries is the lack of attention by managers to safety issues and international standards and agreements such as the ADR.

  13. U10 : Trusted Truck(R) II (phase B).

    2009-01-01

    Phase B of the Trusted Truck II project built on the system developed in Phase A (or Year 1). For the implementation portion of the project, systems were added to the trailer to provide additional diagnostic trailer data that can be sent to the TTM...

  14. 29 CFR 1910.180 - Crawler locomotive and truck cranes.

    2010-07-01

    ... the shaft or spindle with which or about which a wheel rotates. On truck- and wheel-mounted cranes it... and ropes. Cranes designed for railway and automobile wreck clearances are excepted. The requirements..., 1971, shall meet the design specifications of the American National Standard Safety Code for Crawler...

  15. ISAF'S Afghan Truck Drivers: The Overlooked Counterinsurgency Population

    Myron Varouhakis

    2015-12-01

    Full Text Available A yearlong U.S. Army field study in Afghanistan examined the demographics and threat perceptions of one of the most-at-risk populations, that of Afghan truck drivers working for NATO’s International Security Assistance Force Afghanistan (ISAF. The study collected data from 766 Afghan truck drivers at the U.S.-operated Kandahar Airfield in ISAF’s Regional Command South. The findings show a wide diversity in age of the Afghan drivers as well as in terms of their home province. The findings also show that although all Afghan truck drivers had acute awareness and understanding of the high risks and dangers of the job, they all noted that the attractive salary and scarcity of jobs were dominant reasons for staying on the job. Findings also reveal a strong resentment among the Afghan truck drivers about their treatment by ISAF soldiers, as for the lack of protection for them and their families after the 2014 departure of NATO forces. The findings can provide significant insights and enhance the understanding of scholars, counterinsurgency strategists, policymakers, and military planners about “Host Country Nationals” as an important population of the human terrain.

  16. A Qualitative Study of the European Trucking Industry and Logistics Strategies Using the United States Motor Carrier Industry as a Guide

    1992-09-01

    interpretation of the data (Rommerskirchen, 1986:14). In addition to tax differences, the basic costs of operations vary among EC-member states. License fees...aggregation impossible" (Aberle, 1985:18). 4. "Not only are special statistics on nationally specific transport expenditure incomplete, but even the basic ...industry. Various studies concluded that the trucking industry’s collective ratemaking system, composed of regional rate bureaus, resulted in rates in the

  17. The Effects of Caffeine Use on Driving Safety Among Truck Drivers Who Are Habitual Caffeine Users.

    Heaton, Karen; Griffin, Russell

    2015-08-01

    The purpose of this study was to describe caffeine use among a group of habitual caffeine users, truck drivers, and to explore the associations between caffeine use and critical safety events by age in the naturalistic work setting. A secondary analysis of existing data from the Naturalistic Truck Driving Study was conducted. Analyses focused on the association between sleep and caffeine consumption by duty status, comparisons of sleep and caffeine use by age, and the associations between caffeine use and safety-critical events (SCEs). Findings indicated differences in caffeine use by duty status. However, no difference in sleep time by duty status, or between sleep time and caffeine use was found regardless of when the caffeine was consumed during the 5 hours prior to sleep. Sleep time did not vary significantly by age, although increasing age was associated with decreased caffeine use. Overall, a 6% reduction in the rate of SCEs per eight ounces of caffeinated beverage consumed was found. This study makes a unique scientific contribution because it uses real-time observations of truckers in the naturalistic work setting. It also does not involve caffeine withdrawal but rather an investigation of the effects of the naturalistic consumption of caffeine on sleep and driving performance. Findings suggest that caffeine use among habitual users offers a protective effect for safety-critical driving events. Occupational health nurses may use this information to counsel workers in the use of caffeine to enhance driving safety. © 2015 The Author(s).

  18. Shock and vibration environments for large shipping containers on rail cars and trucks

    Magnuson, C.F.; Wilson, L.T.

    1977-06-01

    The purpose of this study was to provide definitions of shock and vibration environment to which fissile material shipping containers may be exposed during normal shipment by truck and rail cars. The definitions of vibration, shock superimposed on vibration and rail coupling shock result from existing data. The dependence of shock environment, from rail coupling operations, on parameters like cargo weight and shock attenuation couplers was also studied using spring-mass models. These studies show that for rail cars equipped with standard draft gear, the cargo response decreases with increased cargo weight until the springs bottom out. For rail cars equipped with shock attenuation couplers, cargo weight has little effect on cargo response. The study also shows the importance of matching couplers and tiedown stiffnesses to decrease the cargo response. Vibration and shock data samples have been obtained during truck shipment of heavy cargo and the data will be presented in subsequent reports. Similar data need to be obtained for rail shipment of heavy cargo and during rail coupling operations with heavy cargo

  19. 77 FR 20480 - Volvo Trucks North America and Mack Trucks, Inc., Grant of Petition for Decision of...

    2012-04-04

    ... GU model trucks that were built with certain Meritor WABCO Vehicle Control Systems (Meritor WABCO... equipment requirements for motor vehicles equipped with air brake systems. Paragraph S5.3.4.1(a) of FMVSS No... vehicle's braking performance. The tests and analyses were performed by an independent test lab, Link...

  20. Idle emissions from medium heavy-duty diesel and gasoline trucks.

    Khan, A B M S; Clark, Nigel N; Gautam, Mridul; Wayne, W Scott; Thompson, Gregory J; Lyons, Donald W

    2009-03-01

    Idle emissions data from 19 medium heavy-duty diesel and gasoline trucks are presented in this paper. Emissions from these trucks were characterized using full-flow exhaust dilution as part of the Coordinating Research Council (CRC) Project E-55/59. Idle emissions data were not available from dedicated measurements, but were extracted from the continuous emissions data on the low-speed transient mode of the medium heavy-duty truck (MHDTLO) cycle. The four gasoline trucks produced very low oxides of nitrogen (NOx) and negligible particulate matter (PM) during idle. However, carbon monoxide (CO) and hydrocarbons (HCs) from these four trucks were approximately 285 and 153 g/hr on average, respectively. The gasoline trucks consumed substantially more fuel at an hourly rate (0.84 gal/hr) than their diesel counterparts (0.44 gal/hr) during idling. The diesel trucks, on the other hand, emitted higher NOx (79 g/hr) and comparatively higher PM (4.1 g/hr), on average, than the gasoline trucks (3.8 g/hr of NOx and 0.9 g/hr of PM, on average). Idle NOx emissions from diesel trucks were high for post-1992 model year engines, but no trends were observed for fuel consumption. Idle emissions and fuel consumption from the medium heavy-duty diesel trucks (MHDDTs) were marginally lower than those from the heavy heavy-duty diesel trucks (HHDDTs), previously reported in the literature.

  1. Advanced vehicle dynamics of heavy trucks with the perspective of road safety

    Trigell, Annika Stensson; Rothhämel, Malte; Pauwelussen, Joop; Kural, Karel

    2017-10-01

    This paper presents state-of-the art within advanced vehicle dynamics of heavy trucks with the perspective of road safety. The most common accidents with heavy trucks involved are truck against passenger cars. Safety critical situations are for example loss of control (such as rollover and lateral stability) and a majority of these occur during speed when cornering. Other critical situations are avoidance manoeuvre and road edge recovery. The dynamic behaviour of heavy trucks have significant differences compared to passenger cars and as a consequence, successful application of vehicle dynamic functions for enhanced safety of trucks might differ from the functions in passenger cars. Here, the differences between vehicle dynamics of heavy trucks and passenger cars are clarified. Advanced vehicle dynamics solutions with the perspective of road safety of trucks are presented, beginning with the topic vehicle stability, followed by the steering system, the braking system and driver assistance systems that differ in some way from that of passenger cars as well.

  2. Analytical approach to determine vertical dynamics of a semi-trailer truck from the point of view of goods protection

    Pidl, Renáta

    2018-01-01

    The overwhelming majority of intercontinental long-haul transportations of goods are usually carried out on road by semi-trailer trucks. Vibration has a major effect regarding the safety of the transport, the load and the transported goods. This paper deals with the logistics goals from the point of view of vibration and summarizes the methods to predict or measure the vibration load in order to design a proper system. From these methods, the focus of this paper is on the computer simulation of the vibration. An analytical method is presented to calculate the vertical dynamics of a semi-trailer truck containing general viscous damping and exposed to harmonic base excitation. For the purpose of a better understanding, the method will be presented through a simplified four degrees-of-freedom (DOF) half-vehicle model, which neglects the stiffness and damping of the tires, thus the four degrees-of-freedom are the vertical and angular displacements of the truck and the trailer. From the vertical and angular accelerations of the trailer, the vertical acceleration of each point of the platform of the trailer can easily be determined, from which the forces acting on the transported goods are given. As a result of this paper the response of the full platform-load-packaging system to any kind of vehicle, any kind of load and any kind of road condition can be analyzed. The peak acceleration of any point on the platform can be determined by the presented analytical method.

  3. Plug-In Hybrid Urban Delivery Truck Technology Demonstration

    Miyasato, Matt [South Coast Air Quality Management District Building Corporation, Diamond Bar, CA (United States); Impllitti, Joseph [South Coast Air Quality Management District Building Corporation, Diamond Bar, CA (United States); Pascal, Amar [South Coast Air Quality Management District Building Corporation, Diamond Bar, CA (United States)

    2015-07-31

    The I-710 and CA-60 highways are key transportation corridors in the Southern California region that are heavily used on a daily basis by heavy duty drayage trucks that transport the cargo from the ports to the inland transportation terminals. These terminals, which include store/warehouses, inland-railways, are anywhere from 5 to 50 miles in distance from the ports. The concentrated operation of these drayage vehicles in these corridors has had and will continue to have a significant impact on the air quality in this region whereby significantly impacting the quality of life in the communities surrounding these corridors. To reduce these negative impacts it is critical that zero and near-zero emission technologies be developed and deployed in the region. A potential local market size of up to 46,000 trucks exists in the South Coast Air Basin, based on near- dock drayage trucks and trucks operating on the I-710 freeway. The South Coast Air Quality Management District (SCAQMD), California Air Resources Board (CARB) and Southern California Association of Governments (SCAG) — the agencies responsible for preparing the State Implementation Plan required under the federal Clean Air Act — have stated that to attain federal air quality standards the region will need to transition to broad use of zero and near zero emission energy sources in cars, trucks and other equipment (Southern California Association of Governments et al, 2011). SCAQMD partnered with Volvo Trucks to develop, build and demonstrate a prototype Class 8 heavy-duty plug-in hybrid drayage truck with significantly reduced emissions and fuel use. Volvo’s approach leveraged the group’s global knowledge and experience in designing and deploying electromobility products. The proprietary hybrid driveline selected for this proof of concept was integrated with multiple enhancements to the complete vehicle in order to maximize the emission and energy impact of electrification. A detailed review of all

  4. 32 CFR 57.1 - Purpose.

    2010-07-01

    ... Individualized Educational Programs (IEP). (4) Monitoring of DoD programs providing EIS, special education, and... INTERVENTION AND SPECIAL EDUCATION SERVICES TO ELIGIBLE DOD DEPENDENTS § 57.1 Purpose. This part: (a... with disabilities (birth through 2 years, inclusive) and their families, and special education and...

  5. Fuel Cell-Powered Lift Truck Fleet Deployment Projects Final Technical Report May 2014

    Klingler, James J [GENCO Infrastructure Solutions, Inc.

    2014-05-06

    The overall objectives of this project were to evaluate the performance, operability and safety of fork lift trucks powered by fuel cells in large distribution centers. This was accomplished by replacing the batteries in over 350 lift trucks with fuel cells at five distribution centers operated by GENCO. The annual cost savings of lift trucks powered by fuel cell power units was between $2,400 and $5,300 per truck compared to battery powered lift trucks, excluding DOE contributions. The greatest savings were in fueling labor costs where a fuel cell powered lift truck could be fueled in a few minutes per day compared to over an hour for battery powered lift trucks which required removal and replacement of batteries. Lift truck operators where generally very satisfied with the performance of the fuel cell power units, primarily because there was no reduction in power over the duration of a shift as experienced with battery powered lift trucks. The operators also appreciated the fast and easy fueling compared to the effort and potential risk of injury associated with switching heavy batteries in and out of lift trucks. There were no safety issues with the fueling or operation of the fuel cells. Although maintenance costs for the fuel cells were higher than for batteries, these costs are expected to decrease significantly in the next generation of fuel cells, making them even more cost effective.

  6. Special Education in Jordan

    Abu-Hamour, Bashir; Al-Hmouz, Hanan

    2014-01-01

    The purpose of this article is to provide a brief background about special education system in Jordan and particularly describes the present types of programmes and legislation provided within the country to students with special needs, as well as integration movement. Jordan has historically provided a limited number of educational opportunities…

  7. Operations experience with the NAC-1 legal weight truck cask

    Viebrock, J.M.; Hoffman, C.C.

    1978-01-01

    The first three years of operation of Nuclear Assurance Corporation's (NAC) four (4) NAC-1 Casks have demonstrated that shipments of spent fuel, fuel rods and other highly irradiated reactor components can be moved routinely by legal weight truck transport. Shipments of these materials have involved some 800,000 miles of highway travel and cask handling at some fifteen different nuclear facilities. This paper presents details on NAC's operations experience with these casks including cask description, cask handling (loading and unloading), pre-shipment testing, facility turnaround and transit times, operator exposure, transport vehicles and shipper/carrier/cask owner responsibilities, actual experience with regard to facility interfacing requirements and operational procedures. Cask and equipment utilization is discussed together with the methods used to control operation costs and to improve the economics of truck transport

  8. Cummins L10G in Kenworth truck 'viable today'

    Anon.

    1996-01-01

    As the culmination of five years of developmental work by Cummins Engines, BC Research Inc., and BC Gas Utility Ltd., a T800 Kenworth truck was outfitted with a new Cummins L10G natural gas engine, and two lightweight fully -wrapped Dynetek cylinders; it was pronounced to be 'a viable clean truck today'. The L10G spark-ignited engine operates at a relatively high peak efficiency of 37 per cent and is commercially available to meet the current California Air Resources Board heavy duty vehicle emission standards without the use of a catalytic converter. The L10G engine produces no particulate emissions, a very significant advantage, in view of the fact that particulate emissions have been identified as major contributors to respiratory ailments

  9. Antecedents of Truck Drivers’ Job Satisfaction and Retention Proneness

    Prockl, Günter; Teller, Christoph; Kotzab, Herbert

    2017-01-01

    is statistically significant. Financial and nonfinancial job properties affect satisfaction with one's employer whereas the former shows a lower impact compared to the latter. Satisfaction with the job and one's employer impacts retention proneness. The contribution of this study was to (1) add...... to the understanding of the factors that predict retention of truck drivers in relationship to job satisfaction and (2) highlight the different roles of financial and nonfinancial job properties in this specific work context.......The aim of this study was to (1) explore the antecedents of truck drivers’ job satisfaction, (2) identify the impact of financial and nonfinancial job properties on satisfaction with the job and with one's employer, and (3) the drivers’ proneness to retaining their jobs. Based on the extant...

  10. Real-Time Dispatch of Petroleum Tank Trucks

    Gerald G. Brown; Glenn W. Graves

    1981-01-01

    A highly automated, real-time dispatch system is described which uses embedded optimization routines to replace extensive manual operations and to reduce substantially operating costs for a nation-wide fleet of petroleum tank trucks. The system is currently used in daily operations by the Order Entry and Dispatch segment of the Chevron U.S.A. Marketing System. Refined petroleum products valued at several billion dollars per year are dispatched from more than 80 bulk terminals on a fleet excee...

  11. Real-Time Dispatch of Petroleum Tank Trucks

    Brown, Gerald G.; Graves, Glenn W.

    1981-01-01

    Management Science, 27, 1, pp. 19-32. (1982 International Management Science Achievement Award Finalist). A highly automated, real-time dispatch system is described which uses embedded optimization routines to replace extensive manual operations and to reduce substantially operating costs for a nation-wide fleet of petroleum tank trucks. The system is currently used in daily operations by the Order Entry and Dispatch segment of the Chevron U.S.A. Marketing System. Refined petroleum produ...

  12. The ethanol heavy-duty truck fleet demonstration project

    NONE

    1997-06-01

    This project was designed to test and demonstrate the use of a high- percentage ethanol-blended fuel in a fleet of heavy-duty, over-the- road trucks, paying particular attention to emissions, performance, and repair and maintenance costs. This project also represents the first public demonstration of the use of ethanol fuels as a viable alternative to conventional diesel fuel in heavy-duty engines.

  13. TITAN Legal Weight Truck cask preliminary design report

    1990-04-01

    The Preliminary Design of the TITAN Legal Weight Truck (LWT) Cask System and Ancillary Equipment is presented in this document. The scope of this document includes the LWT cask with fuel baskets, impact limiters, and lifting and tiedown features; the cask support system for transportation; intermodal transfer skid; personnel barrier; and cask lifting yoke assembly. The results of the tradeoff studies and evaluations that were performed during the preliminary design are presented in Appendix A to this report. 51 figs., 17 tabs

  14. Hydraulic Hybrid Parcel Delivery Truck Deployment, Testing & Demonstration

    Gallo, Jean-Baptiste [Calstart Incorporated, Pasadena, CA (United States)

    2014-03-07

    Although hydraulic hybrid systems have shown promise over the last few years, commercial deployment of these systems has primarily been limited to Class 8 refuse trucks. In 2005, the Hybrid Truck Users Forum initiated the Parcel Delivery Working Group including the largest parcel delivery fleets in North America. The goal of the working group was to evaluate and accelerate commercialization of hydraulic hybrid technology for parcel delivery vehicles. FedEx Ground, Purolator and United Parcel Service (UPS) took delivery of the world’s first commercially available hydraulic hybrid parcel delivery trucks in early 2012. The vehicle chassis includes a Parker Hannifin hydraulic hybrid drive system, integrated and assembled by Freightliner Custom Chassis Corp., with a body installed by Morgan Olson. With funding from the U.S. Department of Energy, CALSTART and its project partners assessed the performance, reliability, maintainability and fleet acceptance of three pre-production Class 6 hydraulic hybrid parcel delivery vehicles using information and data from in-use data collection and on-road testing. This document reports on the deployment of these vehicles operated by FedEx Ground, Purolator and UPS. The results presented provide a comprehensive overview of the performance of commercial hydraulic hybrid vehicles in parcel delivery applications. This project also informs fleets and manufacturers on the overall performance of hydraulic hybrid vehicles, provides insights on how the technology can be both improved and more effectively used. The key findings and recommendations of this project fall into four major categories: -Performance, -Fleet deployment, -Maintenance, -Business case. Hydraulic hybrid technology is relatively new to the market, as commercial vehicles have been introduced only in the past few years in refuse and parcel delivery applications. Successful demonstration could pave the way for additional purchases of hydraulic hybrid vehicles throughout the

  15. Definition and Evaluation of Bus and Truck Automation Operations Concepts

    Tsao, H.-S. Jacob; Botha, Jan L.

    2002-01-01

    Traffic congestion will continue to worsen and likely worsen at a faster rate than ever. People throughput and freight throughput have become critical issues for California and the rest of the nation. PATH has been funding a one-year research project entitled "Definition and Evaluation of Bus and Truck Automation Operations Concepts," proposed by the authors. This report summarizes the results of the research project achieved during the first six months. During those six months, we reviewed l...

  16. Keep on Trucking: An Entrepreneurial Approach to Intratheater Airlift

    2013-02-14

    yet they must all remain effective in order to stay in business.50 Figure 3. Commercial Distribution Example: Walmart 10 As one of the...world’s largest corporations, Walmart provides a good example of an entrepreneurial logistics system (Figure 3). Like the deployed Air Force component, it...is a fleet owner, a distributor, and a retail location operator.51 While Walmart uses trucks, the AMD schedules aircraft as the primary delivery

  17. Analisis dan Perancangan Sistem E-Marketing pada PT. Nordic Lift Truck

    Haris Setia Budi

    2013-06-01

    Full Text Available The purpose of research is to analyze the current marketing system at PT.Nordick Lift Truck in order to identify the existing problems faced by the company and to identify its weaknesses. Additionally, this research designs a web based Marketing system. The system has been designed to give facilitation for customer to get information abaut material of tutorial activity fast and efficient. The methodologies used are literature study, observation, interview, questionaire, analysis and design with 7-stages E-Marketing. It isconcluded that e-CRM system that has been designed supports information access easily and fast. The e-Marketing application consists of features such as Online Register, Contact us, Download, News, and Complaint. It is expected to help deliver and maintain customer satisfaction by building  a close relationship to the customers.

  18. Coordinating decentralized optimization of truck and shovel mining operations

    Cheng, R.; Fraser Forbes, J. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemical and Materials Engineering; San Yip, W. [Suncor Energy, Fort McMurray, AB (Canada)

    2006-07-01

    Canada's oil sands contain the largest known reserve of oil in the world. Oil sands mining uses 3 functional processes, ore hauling, overburden removal and mechanical maintenance. The industry relies mainly on truck-and-shovel technology in its open-pit mining operations which contributes greatly to the overall mining operation cost. Coordination between operating units is crucial for achieving an enterprise-wide optimal operation level. Some of the challenges facing the industry include multiple or conflicting objectives such as minimizing the use of raw materials and energy while maximizing production. The large sets of constraints that define the feasible domain pose as challenge, as does the uncertainty in system parameters. One solution lies in assigning truck resources to various activities. This fully decentralized approach would treat the optimization of ore production, waste removal and equipment maintenance independently. It was emphasized that mine-wide optimal operation can only be achieved by coordinating ore hauling and overburden removal processes. For that reason, this presentation proposed a coordination approach for a decentralized optimization system. The approach is based on the Dantzig-Wolfe decomposition and auction-based methods that have been previously used to decompose large-scale optimization problems. The treatment of discrete variables and coordinator design was described and the method was illustrated with a simple truck and shovel mining simulation study. The approach can be applied to a wide range of applications such as coordinating decentralized optimal control systems and scheduling. 16 refs., 3 tabs., 2 figs.

  19. Image processing system for the measurement of timber truck loads

    Carvalho, Fernando D.; Correia, Bento A. B.; Davies, Roger; Rodrigues, Fernando C.; Freitas, Jose C. A.

    1993-01-01

    The paper industry uses wood as its raw material. To know the quantity of wood in the pile of sawn tree trunks, every truck load entering the plant is measured to determine its volume. The objective of this procedure is to know the solid volume of wood stocked in the plant. Weighing the tree trunks has its own problems, due to their high capacity for absorbing water. Image processing techniques were used to evaluate the volume of a truck load of logs of wood. The system is based on a PC equipped with an image processing board using data flow processors. Three cameras allow image acquisition of the sides and rear of the truck. The lateral images contain information about the sectional area of the logs, and the rear image contains information about the length of the logs. The machine vision system and the implemented algorithms are described. The results being obtained with the industrial prototype that is now installed in a paper mill are also presented.

  20. Truck bomb and insider threats to nuclear facilities

    Hirsch, D.

    1987-01-01

    In the nuclear field, two the these weak links in the security chain are the truck bomb threat and the insider threat. The risks associated with terrorist use of vehicular bombs against nuclear targets surfaced (actually, resurfaced) followed the terrorist attacks on the US Embassy annex and the Marine compound in Leb Concern was expressed that similar attacks against nuclear facilities could result in substantial damage and release of radioactivity. Since the current regulations of the NRC require licensees to protect only against attacks on foot (and even then, only against very small attacking forces), shortly after the Lebanon bombings, that agency commenced an urgent rulemaking to require its licensees to protect against truck bombs. Inexplicably, that rulemaking was called off after research results indicated that the truck bomb threat to nuclear facilities was even more serious than previously thought. Even were nuclear facilities adequately protected against external attack, be the aim theft or sabotage, the greatest security risk to these sites - the threat of action by insiders - would remain. The traditional methods of protecting against the insider threat - such as the two-person rule, strict compartmentalization of vital areas, and design features that make damage to two or more redundant systems by one individual difficult - are generally expensive and have encountered substantial resistance from the nuclear industry, which has restrained the NRC from requiring them

  1. Program specialization

    Marlet, Renaud

    2013-01-01

    This book presents the principles and techniques of program specialization - a general method to make programs faster (and possibly smaller) when some inputs can be known in advance. As an illustration, it describes the architecture of Tempo, an offline program specializer for C that can also specialize code at runtime, and provides figures for concrete applications in various domains. Technical details address issues related to program analysis precision, value reification, incomplete program specialization, strategies to exploit specialized program, incremental specialization, and data speci

  2. IMPROVING THE ORGANIZATION OF THE SHOVEL-TRUCK SYSTEMS IN OPEN-PIT COAL MINES

    Mark KORYAGIN

    2017-06-01

    Full Text Available The aim of the study is to reduce idle times of mining trucks and shovels in an open-pit coal mine. A heuristic algorithm for making dispatching decisions in conditions of dynamic allocation of trucks is developed. Priority parameters for choosing the shovel after the end-of-truck unloading are introduced. Also, an algorithm for searching for the optimal priority parameters to satisfy the required efficiency criterion is developed. This algorithm is based on a simulation model of a shovel-truck system. The proposed approach is applicable in terms of the group of shovels with a common dump point in various open-pit coal mines. The importance of this work lies in the fact that the proposed model takes into account the random factors related with the duration of loading and dumping, truck movement, repair of shovels and haul trucks, as well as the duration of periods between repairs.

  3. Modelling Truck Weigh Stations’ Locations based on Truck Traffic Flow and Overweight Violation: A Case Study in Bosnia and Herzegovina

    Mirsad Kulović

    2018-04-01

    Full Text Available The number of registered commercial freight vehicles is constantly increasing, increasing therefore as well the traffic load on the roads in Bosnia and Herzegovina. A significant part of freight vehicles moving along the main and regional roads are overloaded and cause significant damage to road infrastructure, affect road safety and result in an increase of emissions of harmful gases for people and the environment. The overloading rate is extremely high, in particular with 5-axle trucks representing 58.7%. The research showed that the increased overload level ranges from 10-20% of the maximum permissible weight. The importance of load limits was recognized early in the history of road development. This interrelation led directly to limitations on vehicle loads, and laws were enacted in many countries to establish the maximum allowable motor vehicle sizes and weights. Strict enforcement of motor vehicle size and weight laws is a step toward reducing motor vehicle size and weight violations, heavy truck accidents, and, even more, improving road maintenance, rehabilitation expenditures and road safety. Thus, based on the applied model the objective of this paper is to evaluate and optimize the locations of truck weigh stations on the road network of Bosnia and Herzegovina.

  4. Planning of Truck Platoons: a Literature Review and Directions for Future Research

    Kishore Bhoopalam, Anirudh; Agatz, Niels; Zuidwijk, Rob

    2017-01-01

    textabstractA truck platoon is a set of virtually linked trucks that drive closely behind one another using automated driving technology. Benefits of truck platooning include cost savings, reduced emissions, and more efficient utilization of road capacity. To fully reap these benefits in the initial phases requires careful planning of platoons based on trucks’ itineraries and time schedules. This paper provides a framework to classify various new transportation planning problems that arise in...

  5. Assessing crash risk considering vehicle interactions with trucks using point detector data.

    Hyun, Kyung Kate; Jeong, Kyungsoo; Tok, Andre; Ritchie, Stephen G

    2018-03-12

    Trucks have distinct driving characteristics in general traffic streams such as lower speeds and limitations in acceleration and deceleration. As a consequence, vehicles keep longer headways or frequently change lane when they follow a truck, which is expected to increase crash risk. This study introduces several traffic measures at the individual vehicle level to capture vehicle interactions between trucks and non-trucks and analyzed how the measures affect crash risk under different traffic conditions. The traffic measures were developed using headways obtained from Inductive Loop Detectors (ILDs). In addition, a truck detection algorithm using a Gaussian Mixture (GM) model was developed to identify trucks and to estimate truck exposure from ILD data. Using the identified vehicle types from the GM model, vehicle interaction metrics were categorized into three groups based on the combination of leading and following vehicle types. The effects of the proposed traffic measures on crash risk were modeled in two different cases of prior- and non-crash using a case-control approach utilizing a conditional logistic regression. Results showed that the vehicle interactions between the leading and following vehicle types were highly associated with crash risk, and further showed different impacts on crash risk by traffic conditions. Specifically, crashes were more likely to occur when a truck following a non-truck had shorter average headway but greater headway variance in heavy traffic while a non-truck following a truck had greater headway variance in light traffic. This study obtained meaningful conclusions that vehicle interactions involved with trucks were significantly related to the crash likelihood rather than the measures that estimate average traffic condition such as total volume or average headway of the traffic stream. Copyright © 2018 Elsevier Ltd. All rights reserved.

  6. An innovative food truck chain, strategic planning inspired from the lean start up methodology

    Peñate, Paul Tavares

    2015-01-01

    Mestardo em Marketing Suportada pela abordagem Lean , o Projecto apresenta um modelo de negócios de uma nova marca de Food Truck, inicialmente a ser lançada na Bélgca. Foodies’TruckZ é a marca sugerida para um novo modelo de negócio de Food Truck que procura inovar alavancando economias de escala, sobretudo em Marketing, e através de uma frota co-propriedade das carinhas food truck. Neste modelo de negócio a partilha no investimento do camião, na comunicação e outros aspectos de marketing ...

  7. Electric urban delivery trucks: energy use, greenhouse gas emissions, and cost-effectiveness.

    Lee, Dong-Yeon; Thomas, Valerie M; Brown, Marilyn A

    2013-07-16

    We compare electric and diesel urban delivery trucks in terms of life-cycle energy consumption, greenhouse gas (GHG) emissions, and total cost of ownership (TCO). The relative benefits of electric trucks depend heavily on vehicle efficiency associated with drive cycle, diesel fuel price, travel demand, electric drive battery replacement and price, electricity generation and transmission efficiency, electric truck recharging infrastructure, and purchase price. For a drive cycle with frequent stops and low average speed such as the New York City Cycle (NYCC), electric trucks emit 42-61% less GHGs and consume 32-54% less energy than diesel trucks, depending upon vehicle efficiency cases. Over an array of possible conditions, the median TCO of electric trucks is 22% less than that of diesel trucks on the NYCC. For a drive cycle with less frequent stops and high average speed such as the City-Suburban Heavy Vehicle Cycle (CSHVC), electric trucks emit 19-43% less GHGs and consume 5-34% less energy, but cost 1% more than diesel counterparts. Considering current and projected U.S. regional electricity generation mixes, for the baseline case, the energy use and GHG emissions ratios of electric to diesel trucks range from 48 to 82% and 25 to 89%, respectively.

  8. Was It Really Worth Pain? Refurbishment of Mercedes-Benz Trucks by Botswana Defence Force

    Rangobana, Samuel A; Alkebaisi, Hussain K

    2005-01-01

    .... Logistics statistics, for refurbished trucks returned to user units, are also gathered from the asset management software database, Mincom Ellipse, in use by the Botswana Defence Force Mechanical...

  9. Logistics of in-wood chipping and trucking of chips; Palstahaketuksen logistinen ketju

    Nuuja, J. [Joensuu Univ. (Finland). Faculty of Forestry; Asikainen, A. [Metsaeosaamiskeskus, Joensuu (Finland). Joensuu Science Park

    1996-12-31

    In this study a in wood chipper and truck transport of chips were modelled and studied by discrete-event simulation. The input data, which included stand characteristics and information about transport distances was compiled by GRASS-program. This data based on the inventory done by Forestry Center TAPIO. With the model various transport alternatives were compared and the effect of work condition factors were studied. It was find out, that a long distance transport with interchangeable container truck gives better productivity than a truck with a trailer. This results from shorter loading time for the interchangeable container truck

  10. Logistics of in-wood chipping and trucking of chips; Palstahaketuksen logistinen ketju

    Nuuja, J [Joensuu Univ. (Finland). Faculty of Forestry; Asikainen, A [Metsaeosaamiskeskus, Joensuu (Finland). Joensuu Science Park

    1997-12-31

    In this study a in wood chipper and truck transport of chips were modelled and studied by discrete-event simulation. The input data, which included stand characteristics and information about transport distances was compiled by GRASS-program. This data based on the inventory done by Forestry Center TAPIO. With the model various transport alternatives were compared and the effect of work condition factors were studied. It was find out, that a long distance transport with interchangeable container truck gives better productivity than a truck with a trailer. This results from shorter loading time for the interchangeable container truck

  11. Aberrant Behaviors and Road Accidents among Iranian Truck Drivers, 2010

    Amir Houshang Mehrparvar

    2011-12-01

    Full Text Available structural dimensions of which as well as technologic failures such as road quality, and tech-nical faults of automobiles, need to be assessed in detail. Iran has the first order in the world for deadly road accidents. This study was designed to assess the association between aberrant behaviors of truck drivers and the incidence of road accidents in Yazd, center of Iran, in 2010.Methods: This cross-sectional descriptive-analytic study was conducted on 300 truck drivers in Yazd. We used 3 questionnaires, including one for demographic data, Driver Behavior Questionnaire (DBQ, and one for drivers' self-evaluation of the of their driving.Results: Five types of the behavior had the highest frequency: Misjudge speed of oncoming vehicle when overtaking.; Deliberately disregard the speed limits late at night or very early in the morning.; Ignore 'give way' signs, and narrowly avoid colliding with traffic having right of way.; Stuck behind a slow-moving vehicle on a two-lane highway, you are driven by frustration to try to overtake in risky circumstances.; Drive with only 'half-an-eye' on the road while looking at a map, changing a cassette or radio channel, etc. The more the driver's driv-ing was influenced by emotional and mental states the more deliberate violations and slips.Conclusion: Among truck drivers, safety has not developed sufficiently, and because of the dangers of road accidents both for the drivers and other people and its economic losses, the importance of the presenting some solutions is completely obvious.

  12. Recovery Act--Class 8 Truck Freight Efficiency Improvement Project

    Trucks, Daimler [Daimler Trucks North America Llc, Portland, OR (United States)

    2015-07-26

    Daimler Trucks North America completed a five year, $79.6M project to develop and demonstrate a concept vehicle with at least 50% freight efficiency improvement over a weighted average of several drive cycles relative to a 2009 best-in-class baseline vehicle. DTNA chose a very fuel efficient baseline vehicle, the 2009 Freightliner Cascadia with a DD15 engine, yet successfully demonstrated a 115% freight efficiency improvement. DTNA learned a great deal about the various technologies that were incorporated into Super Truck and those that, through down-selection, were discarded. Some of the technologies competed with each other for efficiency, and notably some of the technologies complemented each other. For example, we found that Super Truck’s improved aerodynamic drag resulted in improved fuel savings from eCoast, relative to a similar vehicle with worse aerodynamic drag. However, some technologies were in direct competition with each other, namely the predictive technologies which use GPS and 3D digital maps to efficiently manage the vehicles kinetic energy through controls and software, versus hybrid which is a much costlier technology that essentially targets the same inefficiency. Furthermore, the benefits of a comprehensive, integrated powertrain/vehicle approach was proven, in which vast improvements in vehicle efficiency (e.g. lower aero drag and driveline losses) enabled engine strategies such as downrating and downspeeding. The joint engine and vehicle developments proved to be a multiplier-effect which resulted in large freight efficiency improvements. Although a large number of technologies made the selection process and were used on the Super Truck demonstrator vehicle, some of the technologies proved not feasible for series production.

  13. Psychoactive substance use by truck drivers: a systematic review.

    Girotto, Edmarlon; Mesas, Arthur Eumann; de Andrade, Selma Maffei; Birolim, Marcela Maria

    2014-01-01

    The aim of this study was to summarise the scientific evidence on the prevalence of psychoactive substance use and on the factors associated with their intake among truck drivers. A systematic review was performed in the databases PubMed, Scientific Electronic Library Online, Latin American and Caribbean Health Sciences, and Cochrane and 36 cross-sectional studies were identified with quantitative results about the use of psychoactive substances by truck drivers. Out of these, 28 were carried out in countries with large land areas and 23 obtained their information through self-reporting. The most frequently studied substances were alcohol (n=25), amphetamines (n=17), marijuana (n=16) and cocaine (n=13). The prevalence of the use of these substances greatly varied: alcohol (0.1-91.0%); amphetamines (0.2-82.5%), marijuana (0.2-29.9%), cocaine (0.1-8.3%). The frequency of substance use was lower in studies that investigated the presence of these substances in biological samples than in those based on self-reported use. In 12 studies that evaluated factors associated with the intake of psychoactive substances, the following stood out: younger age, higher income, longer trips, alcohol consumption, driving in the night shift, travelling interstate routes, long or short sleep, fewer hours of rest, little experience of the driver, connection with small and medium sized companies, income below levels determined by labour agreements, productivity-based earnings and prior involvement in accidents. The frequency of psychoactive substance use by truck drivers seems to be high, although that greatly varies according to the type of substance and the method of collecting the information. The use of these substances was mainly associated with indicators of poor working conditions.

  14. Specialization Patterns

    Schultz, Ulrik Pagh; Lawall, Julia Laetitia; Consel, Charles

    2000-01-01

    Design patterns offer many advantages for software development, but can introduce inefficiency into the final program. Program specialization can eliminate such overheads, but is most effective when targeted by the user to specific bottlenecks. Consequently, we propose that these concepts...... are complementary. Program specialization can optimize programs written using design patterns, and design patterns provide information about the program structure that can guide specialization. Concretely, we propose specialization patterns, which describe how to apply program specialization to optimize uses...... of design patterns. In this paper, we analyze the specialization opportunities provided by specific uses of design patterns. Based on the analysis of each design pattern, we define the associated specialization pattern. These specialization opportunities can be declared using the specialization classes...

  15. Assessing tether anchor labeling and usability in pickup trucks.

    Klinich, Kathleen D; Manary, Miriam A; Malik, Laura A; Flannagan, Carol A; Jermakian, Jessica S

    2018-04-03

    The objective of this study was to investigate vehicle factors associated with child restraint tether use and misuse in pickup trucks and evaluate 4 labeling interventions designed to educate consumers on proper tether use. Volunteer testing was performed with 24 subjects and 4 different pickup trucks. Each subject performed 8 child restraint installations among the 4 pickups using 2 forward-facing restraints: a Britax Marathon G4.1 and an Evenflo Triumph. Vehicles were selected to represent 4 different implementations of tether anchors among pickups: plastic loop routers (Chevrolet Silverado), webbing routers (Ram), back wall anchors (Nissan Frontier), and webbing routers plus metal anchors (Toyota Tundra). Interventions included a diagram label, Quick Response (QR) Code linked to video instruction, coordinating text label, and contrasting text tag. Subjects used the child restraint tether in 93% of trials. However, tether use was completely correct in only 9% of trials. An installation was considered functional if the subject attached the tether to a tether anchor and had a tight installation (ignoring routing and head restraint position); 28% of subjects achieved a functional installation. The most common installation error was attaching the tether hook to the anchor/router directly behind the child restraint (near the top of the seatback) rather than placing the tether through the router and attaching it to the anchor in the adjacent seating position. The Nissan Frontier, with the anchor located on the back wall of the cab, had the highest rate of correct installations but also had the highest rate of attaching the tether to components other than the tether anchor (seat adjustor, child restraint storage hook, around head restraint). None of the labeling interventions had a significant effect on correct installation; not a single subject scanned the QR Code to access the video instruction. Subjects with the most successful installations spent extensive time

  16. 7 CFR 762.121 - Loan purposes.

    2010-01-01

    ... 7 Agriculture 7 2010-01-01 2010-01-01 false Loan purposes. 762.121 Section 762.121 Agriculture... SPECIAL PROGRAMS GUARANTEED FARM LOANS § 762.121 Loan purposes. (a) Operating Loan purposes. (1) Loan... the need to refinance; (viii) Payment of loan closing costs; (ix) Payment of costs associated with...

  17. Evaluating the effects of heavy sugar cane truck operations on repair cost of low volume highways : technical summary report.

    2008-10-01

    Current Louisiana state laws allow truck operators hauling certain agricultural commodities to purchase : overweight permits and haul at gross vehicle weights (GVW) in excess of the legislated GVW limit of : 80,000 lb. For instance, sugar cane trucke...

  18. The application of smart phone, weight-mile truck data to support freight-modeling, performance measures and planning.

    2013-08-01

    Oregon is one of the few states that currently charge a commercial truck weight-mile tax (WMT). The Oregon Department of : Transportation (ODOT) has developed a data-collection system Truck Road Use Electronics (TRUE) to simplify WMT : collec...

  19. 76 FR 22154 - Powered Industrial Trucks Standard; Extension of the Office of Management and Budget's (OMB...

    2011-04-20

    ... manufacturer, paragraph (a)(5) mandates that employers provide a marker on the trucks that identifies the... markers required by paragraphs (a)(3) through (a)(5) remain affixed to trucks and are legible. Paragraphs... . Therefore, OSHA cautions commenters about submitting personal information such as social security numbers...

  20. Analytical solution to energy management guaranteeing battery life for hybrid trucks

    Pham, H.T.; Kessels, J.T.B.A.; van den Bosch, P.P.J.; Huisman, R.G.M.

    2016-01-01

    This paper considers a parallel hybrid electric truck where the tractive force delivered to the wheels can be provided by a conventional internal combustion engine (ICE) and/or a motor generator (MG). This hybrid truck is equipped with a clutch system that is capable of decoupling the ICE and the MG

  1. Research on tractive power of KZC-5 rear dump truck in underground mine

    Lei Zeyong

    2003-01-01

    The tractive power of KZC-5 rear dump truck in underground mine is studied in this paper. The principles and ways of defining the power are discussed. It is proved that the power of KZC-5 rear dump truck in underground mine is reasonable in the industrial scale test

  2. 27 CFR 24.230 - Examination of tank car or tank truck.

    2010-04-01

    ... TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS WINE Spirits § 24.230 Examination of tank car or tank truck. Upon arrival of a tank car or tank truck at the bonded wine premises, the proprietor shall... calibration chart is available at the bonded wine premises, the spirits may be gauged by volume in the tank...

  3. Risk of commercial truck fires in the United States : an exploratory data analysis

    2012-06-29

    Large trucks are involved in only 8 percent of fatal crashes per year, but 17 percent of fatal fires. The scope of the current body of research is limited. Studies have treated truck fires generally as a subset of vehicle fires or in their own right ...

  4. 76 FR 63988 - Pilot Project on NAFTA Trucking Provisions; Pre-Authorization Safety Audits

    2011-10-14

    ...-0097] Pilot Project on NAFTA Trucking Provisions; Pre-Authorization Safety Audits AGENCY: Federal Motor... motor carriers that applied to participate in the Agency's long-haul pilot program to test and... intent to proceed with the initiation of a United States- Mexico cross-border long-haul trucking pilot...

  5. 49 CFR 230.108 - Steam locomotive leading and trailing trucks.

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Steam locomotive leading and trailing trucks. 230... RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS Steam Locomotives and Tenders Trucks, Frames and Equalizing System § 230.108 Steam locomotive leading...

  6. Locomotor diseases among male long-haul truck drivers and other professional drivers

    Jensen, Anker; Kaerlev, Linda; Tüchsen, Finn

    2007-01-01

    -249) and for other truck drivers (SHR: 130, 95% CI: 108-156) compared to bus drivers (SHR: 110, 95% CI: 79-149). All drivers had high SHR for lesions of the ulnar nerve (SHR: 159, 95% CI: 119-207), especially bus drivers (SHR: 197, 95% CI: 116-311). Long-haul truck drivers had high SHRs for synovitis and bursitis...

  7. A Comparative Study of Back Pain among Taxi and Truck Drivers in ...

    Data was analyzed using SSPSS version 20. Descriptive and analytical statistics to analyze and present data. The prevalence of back pain in Port Harcourt for taxi drivers was 70.4% and 71.4% for truck drivers. The prevalence among truck drivers was due to age ,sitting position and shock absorbers. However variables like ...

  8. Trucks involved in fatal accidents codebook 2010 (Version October 22, 2012).

    2012-11-01

    This report provides documentation for UMTRIs file of Trucks Involved in Fatal Accidents : (TIFA), 2010, including distributions of the code values for each variable in the file. The 2010 : TIFA file is a census of all medium and heavy trucks invo...

  9. The Impact of Wireless Technology on Loading Trucks at an Auto Parts Distribution Center

    Goomas, David T.

    2012-01-01

    An intervention was introduced for truck loaders that used wireless vehicle mount computers that included auditory, visual feedback, and immediate data delivery. The implementation reliably reduced pallets from being loaded out of sequence for all outbound trucks in multistop routes. The role of the organizational behavior management (OBM)…

  10. Impact of trucking network flow on preferred biorefinery locations in the southern United States

    Timothy M. Young; Lee D. Han; James H. Perdue; Stephanie R. Hargrove; Frank M. Guess; Xia Huang; Chung-Hao Chen

    2017-01-01

    The impact of the trucking transportation network flow was modeled for the southern United States. The study addresses a gap in existing research by applying a Bayesian logistic regression and Geographic Information System (GIS) geospatial analysis to predict biorefinery site locations. A one-way trucking cost assuming a 128.8 km (80-mile) haul distance was estimated...

  11. Structural evaluation for the core sampling trucks, RMCS operations, 200 Area

    Islam, M.A.

    1996-01-01

    This report evaluates the structural adequacy and the integrity of the existing core sampling trucks to withstand impact should the trucks drop off the ramp, either onto the soft ground or onto a non-yielding surface due to operational error, wind, or earthquake. The report also addresses if the allowable tank dome load will be exceeded by the addition of the impact load

  12. 76 FR 68220 - Navistar Truck Development and Technology Center; a Subsidiary of Navistar International...

    2011-11-03

    ... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-75,151; TA-W-75,151A] Navistar... Renaissance and Alpha Personnel, Inc. Fort Wayne, IN; Navistar Truck Reliability Center, a Subsidiary of... Reliability Center, a Subsidiary of Navistar International Corporation, Truck Division, 3033 Wayne Trace, Fort...

  13. Investigation of RADTRAN Stop Model input parameters for truck stops

    Griego, N.R.; Smith, J.D.; Neuhauser, K.S.

    1996-01-01

    RADTRAN is a computer code for estimating the risks and consequences as transport of radioactive materials (RAM). RADTRAN was developed and is maintained by Sandia National Laboratories for the US Department of Energy (DOE). For incident-free transportation, the dose to persons exposed while the shipment is stopped is frequently a major percentage of the overall dose. This dose is referred to as Stop Dose and is calculated by the Stop Model. Because stop dose is a significant portion of the overall dose associated with RAM transport, the values used as input for the Stop Model are important. Therefore, an investigation of typical values for RADTRAN Stop Parameters for truck stops was performed. The resulting data from these investigations were analyzed to provide mean values, standard deviations, and histograms. Hence, the mean values can be used when an analyst does not have a basis for selecting other input values for the Stop Model. In addition, the histograms and their characteristics can be used to guide statistical sampling techniques to measure sensitivity of the RADTRAN calculated Stop Dose to the uncertainties in the stop model input parameters. This paper discusses the details and presents the results of the investigation of stop model input parameters at truck stops

  14. Conformity checking of LPG Transportation Trucks by Modelling and Simulation

    Gallab Maryam

    2017-01-01

    Full Text Available LPG Loading /unloading site is considered as a dangerous environment of significant risk, especially during LPG transfer operations. These risks may cause catastrophic dangers such as BLEVE (Boiling Liquid Expanding Vapour Explosion, UVCE (Unconfined Vapour Cloud Explosion, etc. The site consists of a tank (RST containing LPG and threetransfer posts. Two posts allow loading of small carrier tankers 6 tons. The other one transfer post transfer LPG contained injumbo tankers 20 tons inside the tank. The industrial site at risks chooses to demonstrate the need for a modelling-simulation approach. The aim is to check first compliance and authorization of the truck when it enters the site for loading /unloading, to verify the authorization to make the transfer, and then, to identify the driver and his training to ensure that the transfer operations are going to take place without incident. Sometimes, it may happen that Consignment Operator (CO is busy orabsent and thus the driver operates alone without being authorized, in this case the site risks a loss of control due to a lack of resources. The modelling-simulation will be done using multi-agent systems that will present the drivers, trucks, PO and loading unloading posts as agents in order to have a model facilitating this checking.

  15. Study of trends in the trucking market in modern conditions

    P.Popovych

    2016-08-01

    Full Text Available The article analyzes the features of the transport services market in accordance with its segmentation from the position of statistics on the field of automotive freight. The tendencies of development dynamics and road trucking transport market structure, and particularly the impact of transportation logistics market, including foreign trade cargo traffic of road transport, on the basic trends and the impact of logistics infrastructure development for aggregate indicators of development of transport communications, the size and dynamics of development, market compatibility on investment attractiveness. Balance of consumer, wholesale and logistics market in Ukraine, having similar development trends are established. Market logistics of trucking transport services have a steady trend of development in an objective decline in growth. The necessity of modernization policies in the transport sector at the state level as a software-oriented transport sector investment resources of the economy, taking into account that the share of road transport in the transport system of the country demonstrates the dynamic development with a positive trend in demand for transportation of goods.

  16. Haul truck tire dynamics due to tire condition

    Anzabi, R Vaghar; Nobes, D S; Lipsett, M G

    2012-01-01

    Pneumatic tires are costly components on large off-road haul trucks used in surface mining operations. Tires are prone to damage during operation, and these events can lead to injuries to personnel, loss of equipment, and reduced productivity. Damage rates have significant variability, due to operating conditions and a range of tire fault modes. Currently, monitoring of tire condition is done by physical inspection; and the mean time between inspections is often longer than the mean time between incipient failure and functional failure of the tire. Options for new condition monitoring methods include off-board thermal imaging and camera-based optical methods for detecting abnormal deformation and surface features, as well as on-board sensors to detect tire faults during vehicle operation. Physics-based modeling of tire dynamics can provide a good understanding of the tire behavior, and give insight into observability requirements for improved monitoring systems. This paper describes a model to simulate the dynamics of haul truck tires when a fault is present to determine the effects of physical parameter changes that relate to faults. To simulate the dynamics, a lumped mass 'quarter-vehicle' model has been used to determine the response of the system to a road profile when a failure changes the original properties of the tire. The result is a model of tire vertical displacement that can be used to detect a fault, which will be tested under field conditions in time-varying conditions.

  17. Haul truck tire dynamics due to tire condition

    Vaghar Anzabi, R.; Nobes, D. S.; Lipsett, M. G.

    2012-05-01

    Pneumatic tires are costly components on large off-road haul trucks used in surface mining operations. Tires are prone to damage during operation, and these events can lead to injuries to personnel, loss of equipment, and reduced productivity. Damage rates have significant variability, due to operating conditions and a range of tire fault modes. Currently, monitoring of tire condition is done by physical inspection; and the mean time between inspections is often longer than the mean time between incipient failure and functional failure of the tire. Options for new condition monitoring methods include off-board thermal imaging and camera-based optical methods for detecting abnormal deformation and surface features, as well as on-board sensors to detect tire faults during vehicle operation. Physics-based modeling of tire dynamics can provide a good understanding of the tire behavior, and give insight into observability requirements for improved monitoring systems. This paper describes a model to simulate the dynamics of haul truck tires when a fault is present to determine the effects of physical parameter changes that relate to faults. To simulate the dynamics, a lumped mass 'quarter-vehicle' model has been used to determine the response of the system to a road profile when a failure changes the original properties of the tire. The result is a model of tire vertical displacement that can be used to detect a fault, which will be tested under field conditions in time-varying conditions.

  18. Urban risks of truck transport of radioactive material

    Mills, G.S.; Neuhauser, K.S.

    1998-01-01

    Truck transport of radioactive material (RAM), e.g., spent nuclear fuel (SNF), normally maximizes use of Interstate highways, which are safer and more efficient for truck transport in general. In the estimation of transportation risks, population bordering a route is a direct factor in determining consequences and an indirect factor in determining exposure times, accident probabilities and severities, and other parameters. Proposals to transport RAM may draw intense resistance from stakeholders based on concern for population concentrations along urban segments but the length of a route segment is also a determinative factor in estimating the transport risks. To quantify the relative importance of these two factors, a potential route for transport of SNF (strict use of Interstate highways) was selected and compared with a modified version that bypassed urban areas. The RADTRAN 4 code for transportation risk assessment, which was developed at Sandia National Laboratories, was used in the present study to assess the relative risks of SNF transportation for alternative routes. The results suggest that emphasis on Interstate highways minimizes total route and urban segment risks

  19. Work-related musculoskeletal discomfort among heavy truck drivers.

    Nazerian, Ramtin; Korhan, Orhan; Shakeri, Ehsan

    2018-03-13

    Heavy truck drivers are exposed to various psychological, psychosocial and physiological factors, some of which can cause musculoskeletal discomfort in different body regions. This study aims to investigate the correlation between different factors of musculoskeletal discomfort in heavy truck drivers. A cross-sectional study design was applied. A total of 384 participants were interviewed using an updated version of the Nordic musculoskeletal questionnaire. While hypothesis testing was used to assess the association of different factors in musculoskeletal discomfort, logistic regression was applied to explore different correlations among questions of the survey. The results demonstrate that hours of exposure to vibration were associated with discomfort in the neck and shoulders (p  0.05. Fifty-seven percent of the drivers were suffering from discomfort in their lower back region. Moreover, seat comfort was found to be highly correlated with discomfort in the neck, shoulder and upper back areas. Additionally, with aging the likelihood of experiencing discomfort in the neck, upper back and knees is increased.

  20. Exploring Telematics Big Data for Truck Platooning Opportunities

    Lammert, Michael P [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Bugbee, Bruce [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Hou, Yi [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Muratori, Matteo [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Holden, Jacob [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Duran, Adam W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Mack, Andrea [Montana State University; Swaney, Eric [Volvo Group

    2018-04-03

    NREL completed a temporal and geospatial analysis of telematics data to estimate the fraction of platoonable miles traveled by class 8 tractor trailers currently in operation. This paper discusses the value and limitations of very large but low time-resolution data sets, and the fuel consumption reduction opportunities from large scale adoption of platooning technology for class 8 highway vehicles in the US based on telematics data. The telematics data set consist of about 57,000 unique vehicles traveling over 210 million miles combined during a two-week period. 75% of the total fuel consumption result from vehicles operating in top gear, suggesting heavy highway utilization. The data is at a one-hour resolution, resulting in a significant fraction of data be uncategorizable, yet significant value can still be extracted from the remaining data. Multiple analysis methods to estimate platoonable miles are discussed. Results indicate that 63% of total miles driven at known hourly-average speeds happens at speeds amenable to platooning. When also considering availability of nearby partner vehicles, results indicate 55.7% of all classifiable miles driven were platoonable. Analysis also address the availability of numerous partners enabling platoons greater than 2 trucks and the percentage of trucks that would be required to be equipped with platooning equipment to realize more than 50% of the possible savings.

  1. Truck Drivers And Risk Of STDs Including HIV

    Bansal R.K

    1995-01-01

    Full Text Available Research Question: Whether long distance truck drivers are at a higher risk of contracting and transmitting STDs including HIV? Objectives: i To study the degree of knowledge of HIV and AIDS among long- distance truck drivers. ii Assess their sexual behaviour including condom use. iii Explore their prevailing social influences and substance abuse patterns. iv Explore their treatment seeking bahaviour as regards STDs. v Deduce their risk of contracting and transmitting STDs including HIV. Study Design: Cross- sectional interview. Setting: Transport Nagar, Indore (M.P Participants: 210 senior drivers (First drivers and 210 junior drivers (Second drivers. Study Variables: Extra-Marital sexual intercourse, condom usage, past and present history of STDs, treatment and counseling, substance abuse, social â€" cultural milieu. Outcome Variables: Risk of contraction of STDs. Statistical Analysis: Univariate analysis. Results: 94% of the drivers were totally ignorant about AIDS. 82.9% and 43.8 % of the senior and junior drivers had a history of extra- marital sex and of these only 2 regularly used condoms. 13.8% and 3.3 % of the senior and junior drivers had a past or present history suggestive of STD infection. Alcohol and Opium were regularly used by them. Conclusion: The studied drivers are at a high risk of contracting and transmitting STDs including HIV.

  2. Scrotal neoplasia: would truck drivers be at greater risk?

    Daniel Seabra

    2007-08-01

    Full Text Available OBJECTIVE: To analyze how scrotal neoplasias have been managed during the past decade and to question possible factors or professions associated to its presence. MATERIALS AND METHODS: We retrospectively evaluated every case reported from 1995 to 2005 at our hospital. We described the clinical scenario, complementary exams, treatments and outcomes. We also tried to verify if there was any risk, predisposing factors or professions that would explain the cancer origin. RESULTS: Six cases were reviewed. Out of these, three patients were truck drivers. Five of them showed restricted lesions without inguinal lymph nodes enlargement. Histologically, six patients presented squamous carcinoma, with two of them having the verrucous type. The median age of patients was 52 years old (31 to 89. The five patients who are still alive had their lesions completely removed with safety margin and primary closure. CONCLUSIONS: We have noticed that the scrotal carcinoma behavior is similar to that of the penis, where removal of the lesion and study of the regional lymph nodes help to increase the patient survival rate. The outstanding fact was that three out of six patients were truck drivers, raising the hypothesis that such profession, maybe due to the contact or attrition with the diesel exhaust expelled by the engine or to sexual promiscuity, would imply in a larger risk of developing this rare neoplasia.

  3. The Production Measurement Model of Open Pit Mine Based on Truck Operation Diagram

    Sun Xiao-Yu

    2016-01-01

    Full Text Available Conventional production measurement of truck dispatching system in open pit mine has not been effectively expressed by a mathematical model, which brings a negative effect on the subsequent data mining and a compatibility issue to apply the production measurement with fixed assignment of truck. In this study, based on the proposed concept that truck is not only the carrier of transport material, but also act as the bridges and linkages between the loading sites and the unloading sites, a new truck operation diagram was established, which was further developed to a basic data matrix and a production measurement model. The new model allowed to calculatethe production measurement of the transport, loading, unloading, material and etc, respectively, as well as with any calculation in combination of more than one factor as needed.It solved the compatibility issue between conventional production measurement and the production measurement of fixed assignment of truck with good practical results.

  4. Technology Roadmap for the 21st Century Truck Program, a government-industry research partnership

    None

    2000-12-01

    The 21st Century Truck Program has been established as a government-industry research partnership to support the development and implementation of commercially viable technologies that will dramatically cut fuel use and emissions of commercial trucks and buses while enhancing their safety and affordability as well as maintaining or enhancing performance. The innovations resulting from this program will reduce dependence on foreign oil, improve our nation's air quality, provide advanced technology for military vehicles, and enhance the competitiveness of the U.S. truck and bus industry while ensuring safe and affordable freight and bus transportation for the nation's economy. This Technology Roadmap for the 21st Century Truck Program has been prepared to guide the development of the technical advancements that will enable the needed improvements in commercial truck fuel economy, emissions, and safety.

  5. Modeling and Design of Hybrid PEM Fuel Cell Systems for Lift Trucks

    Hosseinzadeh, Elham

    driven lift trucks are being used more and more in different companies to reduce their emissions. However, battery driven lift trucks need a long time to recharge and thus may be out of work for a long time. Fuel cell driven lift trucks diminish this problem and are therefore getting more attention...... in a fork-lift truck. In order for the ejector to operate in the largest possible range of load, different approaches (with fixed nozzle and variable nozzle ejectors) have been investigated. Different geometries have been studied in order to optimize the ejector. The optimization is carried out not only...... a virtual fork-lift system. This investigation examines important performance metrics, such as hydrogen consumption and battery SOC as a function of the fuel cell and battery size, control strategy, drive cycle, and load variation for a fork-lift truck system. This study can be used as a benchmark...

  6. Occupational Hydrofluoric Acid Injury from Car and Truck Washing--Washington State, 2001-2013.

    Reeb-Whitaker, Carolyn K; Eckert, Carly M; Anderson, Naomi J; Bonauto, David K

    2015-08-21

    Exposure to hydrofluoric acid (HF) causes corrosive chemical burns and potentially fatal systemic toxicity. Car and truck wash cleaning products, rust removers, and aluminum brighteners often contain HF because it is efficient in breaking down roadway matter. The death of a truck wash worker from ingestion of an HF-based wash product and 48 occupational HF burn cases associated with car and truck washing in Washington State during 2001-2013 are summarized in this report. Among seven hospitalized workers, two required surgery, and all but one worker returned to the job. Among 48 injured workers, job titles were primarily auto detailer, car wash worker, truck wash worker, and truck driver. Because HF exposure can result in potentially severe health outcomes, efforts to identify less hazardous alternatives to HF-based industrial wash products are warranted.

  7. Vehicle to Grid regulation services of electric delivery trucks: Economic and environmental benefit analysis

    Zhao, Yang; Noori, Mehdi; Tatari, Omer

    2016-01-01

    Highlights: • Potential net present revenues of electric truck based V2G regulation services are investigated. • GHG emission mitigation of V2G regulation services provided by electric trucks are quantified. • The total cost of ownership and the life-cycle GHG emissions of electric trucks are also analyzed. • V2G regulation services for electric trucks could yield considerable revenues and GHG emission savings. - Abstract: Concerns regarding the fuel costs and climate change impacts associated with petroleum combustion are among the main driving factors for the adoption of electric vehicles. Future commercial delivery truck fleets may include Battery Electric Vehicles (BEVs) and Extended Range Electric Vehicles (EREVs); in addition to savings on fuel and maintenance costs, the introduction of these grid accessible electric vehicles will also provide fleet owners with possible Vehicle to Grid (V2G) opportunities. This study investigates the potential net present revenues and greenhouse gas (GHG) emission mitigation of V2G regulation services provided by electric trucks in a typical fleet. The total cost of ownership and the life-cycle GHG emissions of electric trucks are also analyzed and compared to those of traditional diesel trucks. To account for uncertainties, possible ranges for key parameters are considered instead of only considering fixed single data values for each parameter. The results of this research indicate that providing V2G regulation services for electric trucks could yield considerable additional revenues ($20,000–50,000) and significant GHG emission savings (approximately 300 ton CO_2) compared to conventional diesel trucks.

  8. 38 CFR 61.0 - Purpose.

    2010-07-01

    ... PROVIDERS GRANT AND PER DIEM PROGRAM § 61.0 Purpose. This part implements the VA Homeless Providers Grant and Per Diem Program which consists of the following components: capital grants, per diem, special...

  9. Adventure travel: oilfield trucking makes highway rigs look tame and light

    Collison, M.

    2000-05-01

    Oilfield trucking as a specialty, involving high stakes in property and health, are discussed. Each rig costs close to one million dollars and operating them, under the watchful eye of GPS satellite or guided by two-way radios, or cellular phones, is a specialty that comes from many years of experience, a Class I licence, special training in first aid, handling dangerous goods and workplace hazardous materials, and readiness to work in mud, slush, and sleet, navigating soft and uneven ground with unwieldy gear and high load ready to tip at any moment. The risks and challenges become even more extreme when the trucker is moving oilfield equipment internationally, where severe climatic conditions, sandstorms, extreme heat and a generally hostile environment, may be augmented by unfamiliar bureaucratic procedures, business practices, and attacks by marauding armed rebel groups. International moves involve internationally recognized shipping terms that define risk and liability between buyer and seller, ocean-safe packaging and complex inventory management. That, of course, is all additional to the trade regulations, import permits, licenses, documentation requirements and insurance procedures of each of the countries traversed during the move.

  10. Potential air toxics hot spots in truck terminals and cabs.

    Smith, Thomas J; Davis, Mary E; Hart, Jaime E; Blicharz, Andrew; Laden, Francine; Garshick, Eric

    2012-12-01

    Hot spots are areas where concentrations of one or more air toxics--organic vapors or particulate matter (PM)--are expected to be elevated. The U.S. Environmental Protection Agency's (EPA*) screening values for air toxics were used in our definition of hot spots. According to the EPA, a screening value "is used to indicate a concentration of a chemical in the air to which a person could be continually exposed for a lifetime ... and which would be unlikely to result in a deleterious effect (either cancer or noncancer health effects)" (U.S. EPA 2006). Our characterization of volatile organic compounds (VOCs; namely 18 hydrocarbons, methyl tert-butyl ether [MTBE], acetone, and aldehydes) was added onto our ongoing National Cancer Institute-funded study of lung cancer and particulate pollutant concentrations (PM with an aerodynamic diameter highways. In Phase 1 of our study, 15 truck terminals across the United States were each visited for five consecutive days. During these site visits, sorbent tubes were used to collect 12-hour integrated samples of hydrocarbons and aldehydes from upwind and downwind fence-line locations as well as inside truck cabs. Meteorologic data and extensive site information were collected with each sample. In Phase 2, repeat visits to six terminals were conducted to test the stability of concentrations across time and judge the representativeness of our previous measurements. During the repeat site visits, the sampling procedure was expanded to include real-time sampling for total hydrocarbon (HC) and PM2.5 at the terminal upwind and downwind sites and inside the truck cabs, two additional monitors in the yard for four-quadrant sampling to better characterize the influence of wind, and indoor sampling in the loading dock and mechanic shop work areas. Mean and median concentrations of VOCs across the sampling locations in and around the truck terminals showed significant variability in the upwind concentrations as well as in the intensity of

  11. Clean Diesel Engine Component Improvement Program Diesel Truck Thermoelectric Generator

    Elsner, N. B. [Hi-Z Technology, Inc., San Diego, CA (United States); Bass, J. C. [Hi-Z Technology, Inc., San Diego, CA (United States); Ghamaty, S. [Hi-Z Technology, Inc., San Diego, CA (United States); Krommenhoek, D. [Hi-Z Technology, Inc., San Diego, CA (United States); Kushch, A. [Hi-Z Technology, Inc., San Diego, CA (United States); Snowden, D. [Hi-Z Technology, Inc., San Diego, CA (United States); Marchetti, S. [Hi-Z Technology, Inc., San Diego, CA (United States)

    2005-03-16

    Hi-Z Technology, Inc. (Hi-Z) is currently developing four different auxiliary generator designs that are used to convert a portion (5 to 20%) of the waste heat from vehicle engines exhaust directly to electricity. The four designs range from 200 Watts to 10 kW. The furthest along is the 1 kW Diesel Truck Thermoelectric Generator (DTTEG) for heavy duty Class 8 Diesel trucks, which, under this program, has been subjected to 543,000 equivalent miles of bouncing and jarring on PACCAR's test track. Test experience on an earlier version of the DTTEG on the same track showed the need for design modifications incorporated in DTTEG Mod 2, such as a heavy duty shock mounting system and reinforcement of the electrical leads mounting system, the thermocouple mounting system and the thermoelectric module restraints. The conclusion of the 543,000 mile test also pointed the way for an upgrading to heavy duty hose or flex connections for the internal coolant connections for the TEG, and consideration of a separate lower temperature cooling loop with its own radiator. Fuel savings of up to $750 per year and a three to five year payback are believed to be possible with the 5 % efficiency modules. The economics are expected to improve considerably to approach a two year payback when the 5 kW to 10 kW generators make it to the market in a few years with a higher efficiency (20%) thermoelectric module system called Quantum Wells, which are currently under development by Hi-Z. Ultimately, as automation takes over to reduce material and labor costs in the high volume production of QW modules, a one year payback for the 5 kW to10 kW generator appears possible. This was one of the stated goals at the beginning of the project. At some future point in time, with the DTTEG becoming standard equipment on all trucks and automobiles, fuel savings from the 25% conversion of exhaust heat to useable electricity nationwide equates to a 10% reduction in the 12 to 15 million barrels per day of

  12. Stress analysis of jacks, frame and bearing connections, and drill rod for core sampler truck No. 2

    Ziada, H.H.

    1995-01-01

    This analysis evaluates the structural design adequacy of several components and connections for the rotary mode core sampler truck (RMCST) No. 2. This analysis was requested by the Characterization Equipment Group (WHC 1994a). The components addressed in this report are listed below: front jack assembly and connection to the truck chassis; rear jack assembly and connection to the truck chassis; center outrigger jacks and connection to the truck chassis; lower frame assembly and connection to the truck chassis; bolt connections for bearing plate assembly (for path of maximum load); traverse slide brackets and mounting of the traverse jack cylinders; and drill rod (failure loads)

  13. Truck acceleration behavior study and acceleration lane length recommendations for metered on-ramps

    Guangchuan Yang

    2016-10-01

    Full Text Available This paper investigated the actual truck acceleration capability at metered on-ramps. Truck acceleration performance data were collected through a video-based data collection method. A piecewise constant acceleration model was employed to capture truck acceleration characteristics. It was found that the existing acceleration length will affect truck drivers’ acceleration behavior. At the taper type ramp that has limited acceleration distance, acceleration profile indicated a decreasing trend with distance. While for the ramp with an auxiliary lane that has sufficient acceleration distance, it was found that the acceleration behavior is to have a high acceleration rate in the beginning, then acceleration rate decrease with speed increase, and high acceleration rate again as drivers approach the merging area. Field data show that the truck acceleration performance data documented in the ITE’s (Institute of Transportation Engineers “Traffic Engineering Handbook” are much lower than the field collected data. Also, based on the regression analysis of speed versus distance profiles, it was found that the AASHTO’s (American Association of State Highway and Transportation Officials Green Book acceleration length design guidance is insufficient to accommodate trucks at metered on-ramps. The required acceleration lengths for medium and heavy trucks are approximately 1.3 and 1.6 times of the Green Book design guideline, respectively.

  14. Design and analysis of truck body for increasing the payload capacity

    Vamshi Krishna, K.; Yugandhar Reddy, K.; Venugopal, K.; Ravi, K.

    2017-11-01

    Truck industry is a major source of transportation in India. With an average truck travelling about 300 kilometers per day [1], every kilogram of truck weight is of concern to the industry in order to get the best out of the truck. The main objective of this project is to increase the payload capacity of automotive truck body. Every kilogram of increased vehicle weight will decrease the vehicle payload capacity in turn increasing the manufacturing cost and reducing the fuel economy by increase the fuel consumption. With the intension of weight reduction, standard truck body has been designed and analyzed in ANSYS software. C-cross section beams were used instead of conventional rectangular box sections to reduce the weight of the body. Light-weight Aluminum alloy Al 6061 T6 is used to increase the payload capacity. The strength of the Truck platform is monitored in terms of deformation and stress concentration. These parameters will be obtained in structural analysis test condition environment. For reducing the stress concentration the concept of beams of uniform strength is used. Accordingly necessary modifications are done so that the optimized model has a better stress distribution and much lesser weight compared to the conventional model. The results obtained by analyzing the modified model are compared with the standard model.

  15. The effect of the descent technique and truck cabin layout on the landing impact forces.

    Patenaude, S; Marchand, D; Samperi, S; Bélanger, M

    2001-12-01

    The majority of injuries to truckers are caused by falls during the descent from the cab of the truck. Several studies have shown that the techniques used to descend from the truck and the layout of the truck's cabin are the principal cause of injury. The goal of the present study was to measure the effects of the descent techniques used by the trucker and the layout of the truck's cabin on the impact forces absorbed by the lower limbs and the back. Kinematic data, obtained with the aid of a video camera, were combined with the force platform data to allow for calculation of the lower limb and L5-S1 torques as well as L5-S1 compressive forces. The trucker descended from two different conventional tractor cabin layouts. Each trucker descended from cabin using either "facing the truck" (FT) or "back to the truck" (BT) techniques. The results demonstrate that the BT technique produces greater ground impact forces than the FT technique, particularly when the truck does not have a handrail. The BT technique also causes an increase in the compressive forces exerted on the back. In conclusion, the use of the FT technique along with the aids (i.e., handrails and all the steps) help lower the landing impact forces as well as the lumbosacral compressive forces.

  16. Combined Aero and Underhood Thermal Analysis for Heavy Duty Trucks

    Vegendla, Prasad [Argonne National Lab. (ANL), Argonne, IL (United States); Sofu, Tanju [Argonne National Lab. (ANL), Argonne, IL (United States); Saha, Rohit [Cummins Inc., Columbus, IN (United States); Madurai Kumar, Mahesh [Cummins Inc., Columbus, IN (United States); Hwang, L. K [Cummins Inc., Columbus, IN (United States)

    2017-01-31

    Aerodynamic analysis of the medium-duty delivery truck was performed to achieve vehicle design optimization. Three dimensional CFD simulations were carried out for several improved designs, with a detailed external component analysis of wheel covers, side skirts, roof fairings, and rounded trailer corners. The overall averaged aerodynamics drag reduction through the design modifications were shown up to 22.3% through aerodynamic considerations alone, which is equivalent to 11.16% fuel savings. The main identified fuel efficiencies were based on second generation devices, including wheel covers, side skirts, roof fairings, and rounded trailer corners. The important findings of this work were; (i) the optimum curvature radius of the rounded trailer edges found to be 125 mm, with an arc length of 196.3 mm, (ii) aerodynamic drag reduction increases with dropping clearance of side skirts between wheels and ground, and (iii) aerodynamic drag reduction increases with an extension of front bumper towards the ground.

  17. Legal weight truck cask model impact limiter response

    Meinert, N.M.; Shappert, L.B.

    1989-01-01

    Dynamic and quasi-static quarter-scale model testing was performed to supplement the analytical case presented in the Nuclear Assurance Corporation Legal Weight Truck (NAC LWT) cask transport licensing application. Four successive drop tests from 9.0 meters (30 feet) onto an unyielding surface and one 1.0-meter (40-inch) drop onto a scale mild steel pin 3.8 centimeters (1.5 inches) in diameter, corroborated the impact limiter design and structural analyses presented in the licensing application. Quantitative measurements, made during drop testing, support the impact limiter analyses. High-speed photography of the tests confirm that only a small amount of energy is elastically stored in the aluminum honeycomb and that oblique drop slapdown is not significant. The qualitative conclusion is that the limiter protected LWT cask will not sustain permanent structural damage and containment will be maintained, subsequent to a hypothetical accident, as shown by structural analyses

  18. Hood of the truck statistics for food animal practitioners.

    Slenning, Barrett D

    2006-03-01

    This article offers some tips on working with statistics and develops four relatively simple procedures to deal with most kinds of data with which veterinarians work. The criterion for a procedure to be a "Hood of the Truck Statistics" (HOT Stats) technique is that it must be simple enough to be done with pencil, paper, and a calculator. The goal of HOT Stats is to have the tools available to run quick analyses in only a few minutes so that decisions can be made in a timely fashion. The discipline allows us to move away from the all-too-common guess work about effects and differences we perceive following a change in treatment or management. The techniques allow us to move toward making more defensible, credible, and more quantifiably "risk-aware" real-time recommendations to our clients.

  19. Burnup credit applications in a high-capacity truck cask

    Boshoven, J.K.

    1992-09-01

    General Atomics (GA) has designed two legal weight truck (LWT) casks, the GA-4 and GA-9, to carry four pressurized-water-reactor (PWR) and nine boiling-water-reactor (BWR) fuel assemblies, respectively. GA plans to submit applications for certification to the US Nuclear Regulatory Commission (NRC) for the two casks in mid-1993. GA will include burnup credit analysis in the Safety Analysis Report for Packaging (SARP) for the GA-4 Cask. By including burnup credit in the criticality safety analysis for PWR fuels with initial enrichments above 3% U-235, public and occupation risks are reduced and cost savings are realized. The GA approach to burnup credit analysis incorporates the information produced in the US Department of Energy Burnup Credit Program. This paper describes the application of burnup credit to the criticality control design of the GA-4 Cask

  20. Waste management (Truck and rail shipments to Hanford)

    O'Donnell, J.P.; Culbertson, R.C.

    1988-01-01

    As part of the physical decommissioning of the Shippingport Atomic Power Station, Shippingport, PA, a large volume of Low Specific Activity (LSA) radioactive waste was accumulated. The waste, which consisted primarily of radioactive reactor plant components, piping, contaminated asbestos, tanks, building rubble, sludge and ion exchange resins was packaged and prepared for shipment. The waste was transported by truck and rail from Shippingport, PA, to the Department of Energy burial ground at Hanford, Washington, a journey of 2,329 miles. This presentation will discuss the successful management of over 2,600 packages weighing in excess of 3,600 tons of radioactive waste from the cradle-to-the-grave, that is from the time it was generated during the decommissioning process until its final burial at the Hanford, Washington burial site. 1 tab

  1. Noise Pollution Aspects of Barge, Railroad, and Truck Transportation,

    1975-04-01

    dBA Trolley 88 dBA 82 dBA 78 dBA 72 dBA Truck 87 dBA 81 dBA 76 dBA 74 dBA Bus 81 dBA 76 dBA 72 dBA 68 dBA Automobile 78 dBA 74 dBA 65 dBA 63 dBA I NO...Environmlent~al Prot~ect~ion Agency, Background Document/linvironment~al Explanat~ion f~or Proposed Int~erstate Rail Carriler Noise Emission Regulat~ions (1974...2). By way of comparison only 0.1 percent automobiles produced this noise level at 70 miles per hour (Figure E-1). Bus and motorcycle noise levels (at

  2. The dynamics of the three-piece-freight truck

    Xia, Fujie

    2002-01-01

    and dynamical contact relations between wheels and rails, the nonlinear suspensions and the nonlinear dry friction damping. For low speeds of the truck the kinematic and dynamical nonlinearities might be linearized, but the very strongly nonlinear suspensions and the dry friction damping can not be linearized...... be numerically simulated. Its applications are illustrated in two simple systems. One is an oscillator with a Coulomb dry friction damper in chapter 2 and the other one is the wedge damper in chapter 3. In the mechanical system it is possible that the degrees of freedom will vary with the different friction...... are derived. Chapter 8 provides the numerical methods for the simulation of the system, the discussion focuses on the differential algebraic equations(DAEs) with discontinuous characteristics caused by the two-dimensional friction. In chapter 9 the numerical investigation is provided. The four general...

  3. Specialization Patterns

    Schultz , Ulrik Pagh; Lawall , Julia ,; Consel , Charles

    1999-01-01

    Design patterns offer numerous advantages for software development, but can introduce inefficiency into the finished program. Program specialization can eliminate such overheads, but is most effective when targeted by the user to specific bottlenecks. Consequently, we propose to consider program specialization and design patterns as complementary concepts. On the one hand, program specialization can optimize object-oriented programs written using design patterns. On the other hand, design pat...

  4. Investigation of the influence of vertical force on the contact between truck tyre and road using finite element analyses

    Moisescu, Alexandra-Raluca; Anghelache, Gabriel

    2017-10-01

    In the modern context of automobile integration with the emerging technologies of the interconnected society, the interaction between tyre and road is an element of major importance for automobile safety systems such as the intelligent tyres, as well as for passenger comfort, fuel economy, environmental protection, infrastructure and vehicle durability. The tyre-road contact generates the distribution of forces exerted on each unit area in the contact patch, therefore the distribution of contact stresses on three orthogonal directions. The numerical investigation of stresses distribution in the contact patch requires the development of finite element models capable of accurately describing the interaction between tyre and rolling surface. The complex finite element model developed for the 11R22.5 truck tyre has been used for investigating the influence of vertical force on the distributions of contact stresses. In addition to these contributions, the paper presents aspects related to the simulation of truck tyre radial stiffness. The influence of tyre rolling has not been taken into consideration, as the purpose of the current research is the investigation of tyre-road contact in stationary conditions.

  5. Research Article Special Issue

    2018-01-15

    trucks) to transport fish/perishable food would return to his country. [5]. ... The owner of the goods (manufacturers and retailers) is ... noticeable practice green logistics management and sustainability overall performance, this.

  6. Research Article Special Issue

    2017-09-10

    Sep 10, 2017 ... Computer Science, Faculty of Defense Science and Technology, Natio ... ncreasing of the number cars on the roads, the rate of road accident ha .... automatically detect and warn oversize trucks and have been introduced to ...

  7. A Clinical Trial on Weight Loss among Truck Drivers

    MS Thiese

    2015-04-01

    Full Text Available Background: The high prevalence of obesity among commercial truck drivers may be related to sedentary nature of the job, lack of healthy eating choices, and lack of exercise. There may be a link between obesity and crash risk, therefore an intervention to reduce obesity in this population is needed. Objective: To assess feasibility of a 12-week weight loss intervention for truck drivers with a weight loss goal of 10% of initial body weight. Methods: Drivers were selected based on age (≥21 years and body mass index (≥30 kg/m2. The drivers participated in a before-after clinical trial. The intervention included a 12-week program that provided information on healthy diet and increasing exercise, and telephone-based coaching using SMART goals. Outcomes included change from baseline in reported energy intake, measured weight, waist, hip, and neck circumference, blood pressure, and point of care capillary blood lipids and hemoglobin A1c. Exit interviews were conducted to gain insight into driver opinions on the program features and usefulness. This study was registered with the NIH Clinical Trials Registry, number NCT02348983. Results: 12 of 13 drivers completed the study. Weight loss was statistically significant (p=0.03. Reported energy (p=0.005, total fat consumption (p=0.04, and saturated fat consumption (p=0.02 intake were also lower after the 12-week intervention. Drivers attributed their weight loss to health coaching and suggested a longer intervention so that they could reach their goal and become accustomed to the changes. Conclusion: This weight loss intervention is feasible for this difficult population. Additional research is needed to compare this intervention with a control group.

  8. Development of a lightweight electric urban delivery truck

    Gillespie, G.; Martin, R.; Vader, S. [Unicell Ltd., Toronto, ON (Canada)

    2007-07-15

    A study was conducted to develop a lightweight urban parcel delivery vehicle that features a composite material, monocoque low-floor body and a zero-emission electric drive system. The long-term goal of project was to produce a vehicle with an energy efficiency that was nearly 90 per cent better than a conventional delivery vehicle. The objectives of the development phase were to complete the structural design of the composite, monocoque low-floor body. Electric drive options were explored to confirm the feasibility in terms of vehicle range, zero emissions and energy efficiency. This involved characterization of the vehicle duty cycle, development of a computer model of the electric powertrain, and simulations to confirm the vehicle's power and energy requirements. The design of the prototype was validated through testing in accordance with recognized vehicle performance tests and an in-service trial by Purolator Courier Ltd., a major Canadian courier service. Testing of the QuickSider delivery truck included vehicle dynamics, energy consumption, safety compliance, and in-service evaluation. No unacceptable stresses, deflections or resonances were identified in the structure. The vehicle's performance was found to be consistent with design expectations. Dynamometer tests have indicated that the ZEV range of the prototype is greater than the targeted 120 km. The overall energy efficiency of the vehicle was 50 per cent, as compared 11 per cent for a conventional diesel delivery truck. It was concluded that an overall energy efficiency of 75 per cent is achievable in production vehicles if improvements are made to the battery system, drive train, regenerative braking and auxiliary systems. 29 figs., 2 appendices.

  9. Special Weapons

    Federal Laboratory Consortium — Supporting Navy special weapons, the division provides an array of engineering services, technical publication support services, logistics support services, safety...

  10. The design and implementation of a garbage truck fleet management system

    Chen, C. H.

    2016-05-01

    Full Text Available In recent years, the improvement of cloud computing and mobile computing techniques has led to the availability of a variety of mobile applications (‘apps’ in the app store. For instance, a garbage truck app that can provide the immediate location of a garbage truck, the location of collection points, and forecasted arrival times of garbage trucks would be useful for mobile users. Since the power consumption of apps on mobile devices if of concern to mobile users, an optimised power-saving mechanism for updating messages, which is based on location information, for a proposed garbage truck fleet management system (GTFMS is proposed and implemented in this paper. The GTFMS is a three- component system that includes the on-board units on garbage trucks, a fleet management system, and a garbage truck app. In this study, an arrival time forecasting method is designed and implemented in the fleet management system, so that the garbage truck app can retrieve the forecasted arrival time via web services. A message updating event is then triggered that reports the location of garbage truck and the forecasted arrival time. In experiments conducted on case studies, the results showed that the mean accuracy of predicted arrival time by the proposed method is about 81.45 per cent. As for power consumption, the cost of traditional mobile apps is 2,880 times that of the mechanism proposed in this study. Consequently, the GTFMS can provide the precise forecasted arrival time of garbage trucks to mobile users, while consuming less power.

  11. Alternative-fueled truck demonstration natural gas program: Caterpillar G3406LE development and demonstration

    NONE

    1995-06-01

    In 1990, the California Energy Commission, the South Coast Air Quality Management District, and the Southern California Gas Company joined together to sponsor the development and demonstration of compressed natural gas engines for Class 8 heavy-duty line-haul trucking applications. This program became part of an overall Alternative-Fueled Truck Demonstration Program, with the goal of advancing the technological development of alternative-fueled engines. The demonstration showed natural gas to be a technically viable fuel for Class 8 truck engines.

  12. The association between adolescent entry into the trucking industry and risk of HIV among long-distance truck drivers in India.

    Mishra, Ram Manohar; Dube, Madhulika; Saggurti, Niranjan; Pandey, Arvind; Mahapatra, Bidhubhusan; Ramesh, Sowmya

    2012-01-01

    This study examines the relationship between entry into the trucking industry during adolescence and both sexually transmitted infections (STIs) and infection by the human immunodeficiency virus (HIV) among long-distance truck drivers in India. Data were sourced from a cross-sectional survey (sample size: 2066) undertaken in 2007 among long-distance truck drivers. The survey spread across major transshipment locations covering the bulk of India's transport volume along four routes. Participants were interviewed about sexual behaviors and were tested for HIV and STIs. The present authors constructed two synthetic cohorts based on the participants' duration of employment in the trucking industry: (1) low (duration ≤ 6 years) and (2) high experience (duration ≥ 7 years). Based on age at entry into the trucking industry, participants were termed as either adolescent (age at entry 4.0%, respectively; adjusted OR: 1.9; 95% CI: 1.2-3.1) and syphilis (5.7% versus 3.5%, respectively; adjusted OR: 1.8; 95% CI: 1.1-3.1). These results suggest the need for focused behavioral change programs in HIV prevention interventions for adolescent truckers in India and elsewhere.

  13. Model based development of cruise control for Mercedes-Benz trucks; Modellbasierte Entwicklung eines Tempomat fuer Mercedes-Benz Trucks

    Wuensche, M. [VDI, Berlin (Germany); Elser, J.; Dorner, J. [DaimlerChrysler AG, Stuttgart (Germany); Wahner, U.; Kanamueller, B. [MathWorks GmbH, Muenchen (Germany)

    2005-07-01

    It was necessary to reengineer the cruise control of Mercedes-Benz Trucks for its world wide use in commercial vehicles of the DaimlerChrysler AG. For this extensive task a new software development process of model based function development and automatic serial code generation was installed and exemplary used. Key aspects of this process are the involvement of software-in-the-loop and hardware-in-the-loop simulation technologies to ensure a high software quality through the whole cycle. The simulation and modeling tool chain consists of Matlab, Simulink and Embedded Coder, therefore the project was realized under assistance of the consulting department of The MathWorks Inc. (orig.)

  14. Specialized science.

    Casadevall, Arturo; Fang, Ferric C

    2014-04-01

    As the body of scientific knowledge in a discipline increases, there is pressure for specialization. Fields spawn subfields that then become entities in themselves that promote further specialization. The process by which scientists join specialized groups has remarkable similarities to the guild system of the middle ages. The advantages of specialization of science include efficiency, the establishment of normative standards, and the potential for greater rigor in experimental research. However, specialization also carries risks of monopoly, monotony, and isolation. The current tendency to judge scientific work by the impact factor of the journal in which it is published may have roots in overspecialization, as scientists are less able to critically evaluate work outside their field than before. Scientists in particular define themselves through group identity and adopt practices that conform to the expectations and dynamics of such groups. As part of our continuing analysis of issues confronting contemporary science, we analyze the emergence and consequences of specialization in science, with a particular emphasis on microbiology, a field highly vulnerable to balkanization along microbial phylogenetic boundaries, and suggest that specialization carries significant costs. We propose measures to mitigate the detrimental effects of scientific specialism.

  15. Special geometry

    Strominger, A.

    1990-01-01

    A special manifold is an allowed target manifold for the vector multiplets of D=4, N=2 supergravity. These manifolds are of interest for string theory because the moduli spaces of Calabi-Yau threefolds and c=9, (2,2) conformal field theories are special. Previous work has given a local, coordinate-dependent characterization of special geometry. A global description of special geometries is given herein, and their properties are studied. A special manifold M of complex dimension n is characterized by the existence of a holomorphic Sp(2n+2,R)xGL(1,C) vector bundle over M with a nowhere-vanishing holomorphic section Ω. The Kaehler potential on M is the logarithm of the Sp(2n+2,R) invariant norm of Ω. (orig.)

  16. Youth Purpose Worldwide: A Tapestry of Possibilities

    Moran, Seana

    2017-01-01

    Interest in youth purpose is growing among scholars around the world. With globalization, better understanding of life purposes in different countries becomes more important as this generation's youth are influenced by ideas and events anywhere. This special issue contributes to this inclusive, worldwide frame of mind by showcasing work done…

  17. 7 CFR 771.5 - Loan purposes.

    2010-01-01

    ... 7 Agriculture 7 2010-01-01 2010-01-01 false Loan purposes. 771.5 Section 771.5 Agriculture... SPECIAL PROGRAMS BOLL WEEVIL ERADICATION LOAN PROGRAM § 771.5 Loan purposes. (a) Loan funds may be used..., travel and office operations; (3) Salaries and benefits. (b) Loan funds may not be used to pay expenses...

  18. Detecting alcohol and illicit drugs in oral fluid samples collected from truck drivers in the state of São Paulo, Brazil.

    Yonamine, Mauricio; Sanches, Livia Rentas; Paranhos, Beatriz Aparecida Passos Bismara; de Almeida, Rafael Menck; Andreuccetti, Gabriel; Leyton, Vilma

    2013-01-01

    Alcohol and drug use by truck drivers is a current problem in Brazil. Though there is evidence that alcohol consumption is occurring in higher proportions, the use of stimulant drugs to avoid fatigue and to maintain the work schedule has also been reported. The purpose of this study was to estimate the incidence of alcohol and illicit drug use among truck drivers on São Paulo state roads. São Paulo is the most populous state in Brazil and has the largest industrial park and economic production in the country. Data were assessed not only using a questionnaire but also, and more reliably, through toxicological analysis of oral fluid samples. Between the years 2002 and 2008, 1250 oral fluid samples were collected from truck drivers on the roads during morning hours. The samples were tested for the presence of alcohol, cocaine, tetrahydrocannabinol (THC), and amphetamine/methamphetamine. A previously published, validated gas chromatographic (gas chromatography-flame ionization detection and gas chromatography-mass spectrometry) method was applied to the samples for alcohol and drug detection. Of the total analyzed samples, 3.1 percent (n = 39) were positive: 1.44 percent (n = 18) were positive for alcohol, 0.64 percent (n = 8) for amphetamines, 0.56 percent (n = 7) for cocaine, and 0.40 percent (n = 5) for THC. In one case, cocaine and THC were detected. The results are indicative of the extent of alcohol and drug use by truck drivers in the state of São Paulo, Brazil. This research provides evidence that not only alcohol but also illicit drug use is a real problem among professional drivers. The use of these substances should be controlled to better promote safe driving conditions on Brazilian roads.

  19. Expansion of the capabilities of the GA-4 legal weight truck spent fuel shipping cask

    Zimmer, A.; Razvi, J.; Johnson, L.; Welch, B.; Lancaster, D.

    2004-01-01

    General Atomics (GA) has developed the Model GA-4 Legal Weight Truck Spent Fuel Cask, a high capacity cask for the transport of four PWR spent fuel assemblies, and obtained a Certificate of Compliance (CoC No. 9226) in 1998 from the US Nuclear Regulatory Commission (NRC). The currently authorized contents in this CoC however, are much more limiting than the actual capability of the GA-4 cask to transport spent PWR fuel assemblies. The purpose of this paper is to show how the authorized contents can be significantly expanded by additional analyses without any changes to the physical design of the package. Using burnup credit per ISG-8 Rev. 2, the authorized contents can be significantly expanded by increasing the maximum enrichment as the burnup increases. Use of burnup credit eliminates much of the criticality imposed limits on authorized package contents, but shielding still limits the use of the cask for the higher burnup, short cooled fuel. By downloading to two assemblies and using shielding inserts, even the high burnup fuel with reasonable cooling times can be transported

  20. Using 3D Multi-Body Simulation to Evaluate Future Truck Technologies

    Gunter, Dave; Bylsma, Wes; Letherwood, Mike; Dennis, Stacey; Argeropoulos, Kris; Teschendorf, Dan; Gorsich, Dave

    2004-01-01

    ... steering, and in-hub electric drive motors. Fully three-dimensional Future Truck models were created using a commercially available modeling and simulation methodology and limited validation studies were performed by comparing model...

  1. Engineering Task Plan for Water Supply for Spray Washers on the Support Trucks

    BOGER, R.M.

    2000-01-01

    This Engineering Task Plan (ETP) defines the task and deliverables associated with the design, fabrication and testing of an improved spray wash system for the Rotary Mode Core Sampling (RMCS) System Support Trucks

  2. Commercial Truck Driver Health and Safety: Exploring Distracted Driving Performance and Self-Reported Driving Skill.

    Stavrinos, Despina; Heaton, Karen; Welburn, Sharon C; McManus, Benjamin; Griffin, Russell; Fine, Philip R

    2016-08-01

    Reducing distracters detrimental to commercial truck driving is a critical component of improving the safety performance of commercial drivers, and makes the highways safer for all drivers. This study used a driving simulator to examine effects of cell phone, texting, and email distractions as well as self-reported driver optimism bias on the driving performance of commercial truck drivers. Results revealed that more visually demanding tasks were related to poorer driving performance. However, the cell phone task resulted in less off-the-road eye glances. Drivers reporting being "very skilled" displayed poorer driving performance than those reporting being "skilled." Onboard communication devices provide a practical, yet visually and manually demanding, solution for connecting drivers and dispatchers. Trucking company policies should minimize interaction between dispatchers and drivers when the truck is in motion. Training facilities should integrate driving simulators into the instruction of commercial drivers, targeting over-confident drivers. © 2016 The Author(s).

  3. Co-simulation of heavy truck tire dynamics and electronic stability control systems (phase A).

    2009-07-01

    Electronic stability control (ESC) systems have been proven to be an effective means of preventing instability and loss of control on both passenger vehicles and heavy trucks. In addition, roll stability algorithms are an effective means of reducing ...

  4. Integrated vehicle-based safety systems (IVBSS) : heavy truck platform field operational test data analysis plan.

    2009-11-23

    This document presents the University of Michigan Transportation Research Institutes plan to perform : analysis of data collected from the heavy truck platform field operational test of the Integrated Vehicle- : Based Safety Systems (IVBSS) progra...

  5. Tracking truck flows with programmable mobile devices for drayage efficiency analysis : final report.

    2016-05-01

    Inefficient use of drayage trucks results in negative externalities in the form of pollution and congestion. A clear : awareness of the current state of drayage efficiency is especially important in Southern California since the cargo : volume at the...

  6. Truck Rates For Selected North, South, And Northeastern Brazilian Soybean Export Transportation Routes

    Department of Agriculture — Compares monthly truck rates from north Mato Grosso and East Tocantins to the ports Itaituba, Porto Velho, Santarém, São Luís, Santos, and Paranaguá. This is figure...

  7. Improved Harmony Search Algorithm for Truck Scheduling Problem in Multiple-Door Cross-Docking Systems

    Zhanzhong Wang

    2018-01-01

    Full Text Available The key of realizing the cross docking is to design the joint of inbound trucks and outbound trucks, so a proper sequence of trucks will make the cross-docking system much more efficient and need less makespan. A cross-docking system is proposed with multiple receiving and shipping dock doors. The objective is to find the best door assignments and the sequences of trucks in the principle of products distribution to minimize the total makespan of cross docking. To solve the problem that is regarded as a mixed integer linear programming (MILP model, three metaheuristics, namely, harmony search (HS, improved harmony search (IHS, and genetic algorithm (GA, are proposed. Furthermore, the fixed parameters are optimized by Taguchi experiments to improve the accuracy of solutions further. Finally, several numerical examples are put forward to evaluate the performances of proposed algorithms.

  8. Surrogate Plant Data Base : Volume 4. Appendix E : Medium and Heavy Truck Manufacturing

    1983-05-01

    This four volume report consists of a data base describing "surrogate" automobile and truck manufacturing plants developed as part of a methodology for evaluating capital investment requirements in new manufacturing facilities to build new fleets of ...

  9. Improving the system of warranty service of trucks in foreign markets

    Irina MAKAROVA

    2015-03-01

    Full Text Available The article is devoted to the practical methods development of improving one of the ways to ensure the health of trucks in the system warranty. Methodology is aimed at optimizing the processes of formation of warranty spare parts kits during the implementation of KAMAZ trucks in foreign markets. The example is given to demonstrate the importance of different factors in the formation of the warranty set for different regions. The algorithm was developed to assess the qualitative composition formed warranty package that will optimize the planning and organization of activity centers to improve operational reliability of commercial trucks. A basis for acceptance of the scientifically-proved decisions is the statistical data analysis of requests monitoring that allows organizing duly replacement of parts with expired service life, and also promotes customer servicing quality improvement and reliability of trucks by prevention of its failures.

  10. Evaluation of the ticketing aggressive cars and trucks (TACT) program in Pennsylvania (071408).

    2009-08-14

    The Pennsylvania State Police and Pennsylvania Department of Transportation implemented the "Ticketing Aggressive Cars and Trucks (TACT)" media and enforcement initiative on a portion of Interstate 81 in southern Pennsylvania, in late 2008. This repo...

  11. Process for evaluating overweight truck corridors serving coastal port regions and border ports of entry

    2017-08-01

    Coastal and inland ports, regional mobility authorities, cities, and counties located near or along the Texas Gulf Coast, and along the border with Mexico, have been granted authority by the state legislature to establish permitted overweight truck c...

  12. Biodiesel and Cold Temperature Effects on Speciated Mobile Source Air Toxics from Modern Diesel Trucks

    Speciated volatile organic compounds (VOCs) with a particular focus on mobile source air toxics (MSATs) were measured in diesel exhaust from three heavy-duty trucks equipped with modern aftertreatment technologies. Emissions testing was conducted on a temperature controlled chass...

  13. Biodiesel and Cold Temperature Effect on Speciated Mobile Source Air Toxics from Modern Diesel Trucks

    Speciated volatile organic compounds (VOCs) with a particular focus on mobile source air toxics (MSATs) were measured in diesel exhaust from three heavy-duty trucks equipped with modern aftertreatment technologies. Emissions testing was conducted on a temperature controlled chass...

  14. Strategic Design for Delivery with Linked Transportation Assets : Trucks and Drones

    2018-01-01

    Home delivery by drones as an alternative or complement to traditional delivery by trucks is attracting considerable attention from major retailers and services, as well as startups. While drone delivery may offer considerable economic savings, the f...

  15. Modelling and control of a light-duty hybrid electric truck

    Park, Jong-Kyu

    2006-01-01

    This study is concentrated on modelling and developing the controller for the light-duty hybrid electric truck. The hybrid electric vehicle has advantages in fuel economy. However, there have been relatively few studies on commercial HEVs, whilst a considerable number of studies on the hybrid electric system have been conducted in the field of passenger cars. So the current status and the methodologies to develop the LD hybrid electric truck model have been studied through the ...

  16. GA-4 and GA-9 legal weight truck shipping cask development

    Grenier, R.M.; Meyer, R.J.; Jensen, M.F.

    1989-02-01

    We are developing two new legal weight truck spent fuel shipping casks that will carry four PWR or nine BWR spent fuel assemblies. They are being developed to meet requirements to dispose of nuclear wastes at a permanent disposal site. Our primary goal is to maximize the number of fuel elements of each fuel type that a legal weight truck (LWT) cask can carry, while ensuring that the design meets all NRC licensing requirements. 1 ref., 4 figs

  17. Field Measurement of Dynamic Compressive Stress Response of Pavement-Subgrade Induced by Moving Heavy-Duty Trucks

    Lingshi An

    2018-01-01

    Full Text Available This paper presents the dynamic compressive stress response of pavement-subgrade induced by moving heavy-duty trucks. In order to study the distribution characteristic of dynamic pressure of pavement-subgrade in more detail, truck loadings, truck speeds, and dynamic pressure distributions at different depths were monitored under twenty-five working conditions on the section of Qiqihar-Nenjiang Highway in Heilongjiang Province, China. The effects of truck loading, truck speed, and depth on dynamic compressive stress response can be concluded as follows: (1 increasing truck loading will increase the dynamic pressure amplitude of subgrade-pavement and dominant frequencies are close to the characteristic frequencies caused by heavy-duty trucks at the speed of 70 km/h; (2 as truck speed increases, the dynamic pressure amplitudes of measuring points have an increasing tendency; the dynamic pressure spectrums are also significantly influenced by truck speed: the higher the truck speed, the wider the spectrum and the higher the dominant frequencies; (3 as depth increases, the dynamic pressure amplitudes of measuring points decrease rapidly. The influence of the front axle decreases gradually until disappearing and the compressive stress superposition phenomenon caused by rear double axles can be found with increasing depth.

  18. Evacuating populations with special needs

    2009-04-01

    Evacuation operations are conducted under the authority of, and based on decisions by, local and state authorities. The purpose of this primer, Evacuating Populations with Special Needs, is to provide local and state emergency managers, government of...

  19. Study on heavy duty truck stability control by braking force control; Seidoryoku seigyo ni yoru truck no sharyo kyodo anteika ni taisuru ichikosatsu

    Matsuda, K; Shinjo, H; Harada, M; Ohata, K; Sakata, K [Mitsubishi Motors Corp., Tokyo (Japan)

    1997-10-01

    Now a days we are discussing about the vehicle stability control system which freely controls the braking force of each wheel to apply the yaw t and decelerate the vehicle. The system drastically improve the vehicle cornering performance and stabilize the vehicle behavior in its critical area. This paper discusses a point to notice in case of applying this technique for heavy duty trucks, and describes the possibility of the stabilization for vehicle cornering behavior about heavy duty truck. 3 refs., 10 figs., 2 tabs.

  20. An empirical study of DSRC V2V performance in truck platooning scenarios

    Song Gao

    2016-11-01

    Full Text Available Among many safety applications enabled by Dedicated Short Range Communication (DSRC, truck platooning provides many incentives to commercial companies. This paper studies DSRC Vehicle-to-Vehicle (V2V performance in truck platooning scenarios through real-world experiments. Commercial DSRC equipments and semi-trailer trucks are used in this study. We mount one DSRC antenna on each side of the truck. One set of dynamic tests and a few sets of static tests are conducted to explore DSRC behaviors under different situations. From the test results, we verified some of our speculations. For example, hilly roads can affect delivery ratio and antennas mounted on opposite sides of a truck can suffer from low delivery ratio at curved roads. In addition, we also found that antennas can sometimes suffer from low delivery ratio even when the trucks are on straight roads, possibly due to reflections from the nearby terrain. Fortunately, the delivery ratio can be greatly improved by using the two side antennas alternately.

  1. The analysis of loading losses from tank trucks

    Jovanović Ana P.

    2006-01-01

    Full Text Available The quantity of loading losses, which are the primary source of evaporative emissions from tank cars and trucks was analyzed in this paper. Loading losses occur as organic vapors in "empty" cargo tanks are displaced to the atmosphere by the liquid being loaded into the tanks. Emissions from loading petroleum liquid were estimated using three methods: the API (American Petroleum Institute method, the VDI (Verein Deutscher Ingenieure -Association of German Engineers method and the Yugoslav Standard JUS B.HO.531 method. The mass of evaporative losses from loading operations is a function of the following parameters: the method of loading the cargo, the physical and chemical characteristics of the cargo and the ambient temperature during loading. Evaporation losses from the loading of motor gasoline (MB-95, BMB-95, MB-98 and MB-86 and diesel fuels (D-2, Euro D-2 were calculated. Losses on a monthly and annual basis were presented for an assumed amount of loaded cargo. It was estimated that the highest loading losses occur in the summer period because of high ambient daily temperatures and in the period of higher transporting levels. It should be pointed out that the loading losses of diesel fuel calculated using an empirical coefficient according to JUS B.HO.531 are significantly higher in comparison with the loading losses calculated using emission factors from the EPA and the VDI method. The gasoline loading losses calculated using emission factors derived from the three methods are similar.

  2. Workplace violence in long haul trucking: occupational health nursing update.

    Anderson, Debra Gay

    2004-01-01

    Almost 2 million workdays and millions of dollars are lost annually because of non-fatal assaults suffered at the workplace (NIOSH, 1996). Twenty workers, on average, are murdered each week in the United States and an estimated 18,000 workers per week are victims of non-fatal assault (NIOSH, 2001). Violence and stress are two interrelated issues that affect the work force. In-depth studies of these issues have not been conducted with long haul truckers in general, or with women in non-traditional, male dominated fields such as the long haul trucking industry. Epidemiological data related to violence and stress experienced by these under-studied populations are needed to plan effective interventions to reduce occupational risks. Studies employing both qualitative and quantitative methods are needed to articulate risk and protective factors related to violence against workers (Runyan, 2001). Occupational health nurses are qualified to participate in the development and implementation of research and intervention studies to improve worker safety related to violence at the workplace for men and women in both traditional and non-traditional occupational roles.

  3. Design of special purpose equipment - remote control dozer

    Aprameyan, K.

    1990-01-01

    Operation environment in handling hot slag, radio active material, clearing/dismantling buildings and loose rocky zones pose hazards with the operation of heavy duty vehicles. Under such hazardous environment conditions, elimination of operator becomes the prime criteria. Remote control of heavy vehicles is resorted to operate the equipment in various working conditions. Radio control systems coupled with penumatic/hydraulic actuators and proportional control logics aim total control of the equipment from a distance using hand pendants. Bharat Earth Moovers Limited has successfully developed remote control system for dozers of 200hp and 300hp. (author). 3 figs

  4. Supporting special-purpose health care models via Web interfaces

    Warren, James R.; Frankel, Heath K.; Noone, Joseph T.; van der Zwaag, B.J.

    The potential of the Web, via both the Internet and intranets, to facilitate development of clinical information systems has been evident for some time. Most Web-based clinical workstations interfaces, however, provide merely a loose collection of access channels. There are numerous examples of

  5. 7 CFR 917.43 - Special purpose shipments.

    2010-01-01

    ... Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing... marketing research and development projects established pursuant to § 917.39); or (3) in such minimum... prevent fruit handled under the provisions of this section from entering the channels of trade for other...

  6. 7 CFR 920.54 - Special purpose shipments.

    2010-01-01

    ... Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing... (including shipments to facilitate the conduct of marketing research and development projects); or, (3) in... prevent kiwifruit handled under the provisions of this section from entering the channels of trade for...

  7. 7 CFR 922.54 - Special purpose shipments.

    2010-01-01

    ... Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing... conduct of marketing research and development projects established pursuant to § 922.45), as the committee... handled under the provisions of this section from entering the channels of trade for other than the...

  8. 7 CFR 916.54 - Special purpose shipments.

    2010-01-01

    ... Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing... of marketing research and development projects established pursuant to § 916.45), or in such minimum... handled under the provisions of this section from entering the channels of trade for other than the...

  9. 7 CFR 924.54 - Special purpose shipments.

    2010-01-01

    ... Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing... shipments to facilitate the conduct of marketing research and development projects established pursuant to... necessary to prevent prunes handled under the provisions of this section from entering the channels of trade...

  10. Special purpose processors for high energy physics applications

    Verkerk, C.

    1978-01-01

    The review on the subject of hardware processors from very fast decision logic for the split field magnet facility at CERN, to a point-finding processor used to relieve the data-acquisition minicomputer from the task of monitoring the SPS experiment is given. Block diagrams of decision making processor, point-finding processor, complanarity and opening angle processor and programmable track selector module are presented and discussed. The applications of fully programmable but slower processor on the one hand, and very fast and programmable decision logic on the other hand are given in this review

  11. Collocability in Languages for Special Purposes (LSPs): Some ...

    or by computer - of units of meaning which comprise more than one (ortho)- ... cases, of course, it is a question of locating stable and authentic multiword ... based on new relationships and a new dialectic, plus a new or at least ... lysis of LSP discourse by "frontal attack" requires an exceedingly well- ..... risk of hypertension.

  12. Special-purpose multifingered robotic end-effectors

    Crowder, R.M.

    1990-01-01

    A number of advanced multifingered robotic end-effectors have been developed recently in which the finger joints are powered from external actuators. Although this gives dexterous performance, there are considerable problems with power transmission, due to the use of flexible tendons between the external actuators and the individual finger joints. If a multifingered robotic end-effector is to be operated in a confined space, local actuation of the fingers needs to be fully considered, even if there is a reduction in hand dexterity over that of an externally mounted actuator system. The University of Southampton has developed a number of end-effectors that incorporate integral finger actuators and mechanisms, two examples of which are discussed in this paper

  13. Special Purpose Vehicle Institutions: Their Business Natures and Accounting Implications

    Ainun Na'im

    2013-06-01

    The huge financial and accounting scandals such as Enron involved the use of SPVs for not reporting or undervaluing debt and overvaluing net worth. In Indonesia, there are some transactions that are under public scrutiny that use SPVs, such as the sales of the government stocks of BCA Bank, and PT Indosat. There are also many successful and beneficial uses of SPVs in Indonesia as well, such as those in energy development, oil refinery, and telecommunication projects.

  14. Waste truck-tyre processing by flash pyrolysis in a conical spouted bed reactor

    Lopez, G.; Alvarez, J.; Amutio, M.; Mkhize, N.M.; Danon, B.; Gryp, P.; Görgens, J.F. van der; Bilbao, J.; Olazar, M.

    2017-01-01

    Highlights: • Flash pyrolysis improves TPO and limonene yields vs. slow pyrolysis. • The most suitable temperature for TPO and limonene maximization was 475 °C. • Operating at 575 °C gas yields and char quality was enhanced. • Temperature showed a limited effect on sulphur distribution among products. - Abstract: The flash pyrolysis of waste truck-tyres was studied in a conical spouted bed reactor (CSBR) operating in continuous regime. The influence of temperature on product distribution was analysed in the 425–575 °C range. A detailed characterization of the pyrolysis products was carried out in order to assess their most feasible application. Moreover, special attention was paid to the sulphur distribution among the products. The analysis of gaseous products was carried out using a micro-GC and the tyre pyrolysis oil (TPO) by means of GC-FID using peak areas for quantification, with GC/MS for identification and elemental analysis. Finally, the char was subjected to elemental analysis and surface characterization. According to the results, 475 °C is an appropriate temperature for the pyrolysis of waste tyres, given that it ensures total devolatilisation of tyre rubber and a high TPO yield, 58.2 wt.%. Moreover, the quality of the oil is optimum at this temperature, especially in terms of high concentrations of valuable chemicals, such as limonene. An increase in temperature to 575 °C reduced the TPO yield to 53.9 wt.% and substantially changed its chemical composition by increasing the aromatic content. However, the quality of the recovered char was improved at high temperatures.

  15. 40 CFR 421.251 - Specialized definitions.

    2010-07-01

    ... AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Precious Metals and Mercury Subcategory § 421.251 Specialized definitions. For the purpose of this subpart the general...

  16. Combining Purpose With Profits

    Julian Birkinshaw, Julian; Foss, Nicolai Juul; Lindenberg, Siegwart

    2014-01-01

    A sense of purpose that transcends making money can motivate employees. But to sustain both a sense of purpose and a solid level of profitability over time, companies need to pay attention to several fundamental organizing principles....

  17. Carbon and energy footprints of electric delivery trucks:a hybrid multi-regional input-output life cycle assessment

    Zhao, Yang; Onat, Nuri Cihat; Küçükvar, Murat; Tatari, Ömer

    2016-01-01

    Due to frequent stop-and-go operation and long idling periods when driving in congested urban areas, the electrification of commercial delivery trucks has become an interesting topic nationwide. In this study, environmental impacts of various alternative delivery trucks including battery electric, diesel, diesel-electric hybrid, and compressed natural gas trucks are analyzed. A novel life cycle assessment method, an environmentally-extended multi-region input-output analysis, is utilized to c...

  18. An analysis of the lifestyle risk factors for long-distance truck drivers / Barend Koortzen von Wielligh

    Von Wielligh, Barend Koortzen

    2014-01-01

    The Road Freight Industry accounts for 1 to 5 percent of most countries GDP (AECOM International Development, 2011). According to e-Natis there was 321 056 Trucks (Heavy load Vehicle GVM > 3500 kg) in South Africa by November 2009 (Arrive Alive, 2009). This relative big industry, according to the statistics, influences most other industries value chains. Vehicles are driven by trucks drivers, making driving trucks their living. These drivers have their own lifestyles and ways that they go abo...

  19. Special relativity

    Taylor, J.G.

    1975-01-01

    It is stated that the early chapters review special relativity from an elementary mathematical viewpoint, and include discussion of recent experiments which set out to test Einstein's predictions. The theory of relativity is then reformulated in more sophisticated mathematical language to show its relation to electro-magnetism, and to lay the foundation for more general viewpoints. The final chapter discusses in simple terms where activity in the field is currently centred, and where future interest lies. Chapter headings include: the constant speed of light; measuring time and distance; the Lorentz transformation (relativity of simultaneity, space-time and causality); relativistic kinematics (including - the Dopper effect); relativistic dynamics (including - nuclear binding energy, particle creation, electrodynamics); the structure of special relativity (including - the Lorentz group, the rotation group, elementary particle scattering); extensions of special relativity. (U.K.)

  20. Purpose and Professional Writers.

    Blyler, Nancy Roundy

    1989-01-01

    Describes a protocol study of 10 professional writers which examined the meaning and influence of purpose on writers in the workplace. Explores the interactions of various purpose considerations derived from situation, reader, and text. Suggests that professional writers have a range of meanings in mind when they think about purpose. (MM)

  1. Particulate matters from diesel heavy duty trucks exhaust versus cigarettes emissions: a new educational antismoking instrument.

    De Marco, Cinzia; Ruprecht, Ario Alberto; Pozzi, Paolo; Munarini, Elena; Ogliari, Anna Chiara; Mazza, Roberto; Boffi, Roberto

    2015-01-01

    Indoor smoking in public places and workplaces is forbidden in Italy since 2003, but some health concerns are arising from outdoor secondhand smoke (SHS) exposure for non-smokers. One of the biggest Italian Steel Manufacturer, with several factories in Italy and abroad, the Marcegaglia Group, recently introduced the outdoor smoking ban within the perimeter of all their factories. In order to encourage their smoker employees to quit, the Marcegaglia management decided to set up an educational framework by measuring the PM1, PM2.5 and PM10 emissions from heavy duty trucks and to compare them with the emissions of cigarettes in an indoor controlled environment under the same conditions. The exhaust pipe of two trucks powered by a diesel engine of about 13.000/14.000 cc(3) were connected with a flexible hose to a hole in the window of a container of 36 m(3) volume used as field office. The trucks operated idling for 8 min and then, after adequate office ventilation, a smoker smoked a cigarette. Particulate matter emission was thereafter analyzed. Cigarette pollution was much higher than the heavy duty truck one. Mean of the two tests was: PM1 truck 125.0(47.0), cigarettes 231.7(90.9) p = 0.002; PM2.5 truck 250.8(98.7), cigarettes 591.8(306.1) p = 0.006; PM10 truck 255.8(52.4), cigarettes 624.0(321.6) p = 0.002. Our findings may be important for policies that aim reducing outdoor SHS exposure. They may also help smokers to quit tobacco dependence by giving them an educational perspective that rebuts the common alibi that traffic pollution is more dangerous than cigarettes pollution.

  2. Truck drivers’ perceptions on wearable devices and health promotion: a qualitative study

    Rama Greenfield

    2016-07-01

    Full Text Available Abstract Background Professional truck drivers, as other shift workers, have been identified as a high-risk group for various health conditions including cardiovascular disease, obesity, diabetes, sleep apnoea and stress. Mobile health technologies can potentially improve the health and wellbeing of people with a sedentary lifestyle such as truck drivers. Yet, only a few studies on health promotion interventions related to mobile health technologies for truck drivers have been conducted. We aimed to explore professional truck drivers’ views on health promotion delivered via mobile health technologies such as wearable devices. Methods We conducted a phenomenological qualitative study, consisting of four semi-structured focus groups with 34 full-time professional truck drivers in the UK. The focus groups were audio-taped, transcribed verbatim and analysed using thematic content analysis. We discussed drivers’ perceptions of their health, lifestyle and work environment, and their past experience and expectations from mobile health technologies. Results The participants viewed their lifestyle as unhealthy and were aware of possible consequences. They expressed the need and wish to change their lifestyle, yet perceived it as an inherent, unavoidable outcome of their occupation. Current health improvement initiatives were not always aligned with their working conditions. The participants were generally willing to use mobile health technologies such as wearable devices, as a preventive measure to avoid prospect morbidity, particularly cardiovascular diseases. They were ambivalent about privacy and the risk of their employer’s monitoring their clinical data. Conclusions Wearable devices may offer new possibilities for improving the health and wellbeing of truck drivers. Drivers were aware of their unhealthy lifestyle. They were interested in changing their lifestyle and health. Drivers raised concerns regarding being continuously monitored by

  3. Carbon monoxide poisoning in children riding in the back of pickup trucks.

    Hampson, N B; Norkool, D M

    OBJECTIVE - To describe the case characteristics of a series of children poisoned with carbon monoxide while traveling in the back of pickup trucks. DESIGN - Pediatric cases referred for treatment of carbon monoxide poisoning with hyperbaric oxygen between 1986 and 1991 were reviewed. Those cases that occurred during travel in the back of pickup trucks were selected. Clinical follow-up by telephone interview ranged from 2 to 55 months. SETTING - A private, urban, tertiary care center in Seattle, Wash. PATIENTS - Twenty children ranging from 4 to 16 years of age. INTERVENTION - All patients were treated with hyperbaric oxygen. MAIN OUTCOME MEASURES - Characteristics of the poisoning incident and clinical patient outcome. RESULTS - Of 68 pediatric patients treated for accidental carbon monoxide poisoning, 20 cases occurred as children rode in the back of pickup trucks. In 17 of these, the children were riding under a rigid closed canopy on the rear of the truck, while three episodes occurred as children rode beneath a tarpaulin. Average carboxyhemoglobin level on emergency department presentation was 18.2% +/- 2.4% (mean +/- SEM; range, 1.6% to 37.0%). Loss of consciousness occurred in 15 of the 20 children. One child died of cerebral edema, one had permanent neurologic deficits, and 18 had no recognizable sequelae related to the episode. In all cases, the truck exhaust system had a previously known leak or a tail pipe that exited at the rear rather than at the side of the pickup truck. CONCLUSIONS - Carbon monoxide poisoning is a significant hazard for children who ride in the back of pickup trucks. If possible, this practice should be avoided.

  4. Demonstration Project 111, ITS/CVO Technology Truck, Final Project Report

    Gambrell, KP

    2002-01-11

    In 1995, the planning and building processes began to design and develop a mobile demonstration unit that could travel across the nation and be used as an effective outreach tool. In 1997, the unit was completed; and from June 1997 until December 2000, the Federal Highway Administration (FHWA)/Federal Motor Carrier Safety Administration (FMCSA) mobilized the Technology Truck, also known as Demonstration Project No. 111, ''Advanced Motor Carrier Operations and Safety Technologies.'' The project featured the latest available state-of-the-practice intelligent transportation systems (ITS) technologies designed to improve both the efficiency and safety of commercial vehicle operations (CVO). The Technology Truck was designed to inform and educate the motor carrier community and other stakeholders regarding ITS technologies, thus gaining support and buy-in for participation in the ITS program. The primary objective of the project was to demonstrate new and emerging ITS/CVO technologies and programs, showing their impact on motor carrier safety and productivity. In order to meet the objectives of the Technology Truck project, the FHWA/FMCSA formed public/private partnerships with industry and with Oak Ridge National Laboratory to demonstrate and display available ITS/CVO technologies in a cooperative effort. The mobile demonstration unit was showcased at national and regional conferences, symposiums, universities, truck shows and other venues, in an effort to reach as many potential users and decision makers as possible. By the end of the touring phase, the ITS/CVO Technology Truck had been demonstrated in 38 states, 4 Canadian provinces, 88 cities, and 114 events; been toured by 18,099 people; and traveled 115,233 miles. The market penetration for the Technology Truck exceeded 4,000,000, and the website received more than 25,000 hits. In addition to the Truck's visits, the portable ITS/CVO kiosk was demonstrated at 31 events in 23 cites in 15

  5. Modeling mechanical restriction differences between car and heavy truck in two-lane cellular automata traffic flow model

    Li, Xin; Li, Xingang; Xiao, Yao; Jia, Bin

    2016-06-01

    Real traffic is heterogeneous with car and truck. Due to mechanical restrictions, the car and the truck have different limited deceleration capabilities, which are important factors in safety driving. This paper extends the single lane safety driving (SD) model with limited deceleration capability to two-lane SD model, in which car-truck heterogeneous traffic is considered. A car has a larger limited deceleration capability while a heavy truck has a smaller limited deceleration capability as a result of loaded goods. Then the safety driving conditions are different as the types of the following and the leading vehicles vary. In order to eliminate the well-known plug in heterogeneous two-lane traffic, it is assumed that heavy truck has active deceleration behavior when the heavy truck perceives the forming plug. The lane-changing decisions are also determined by the safety driving conditions. The fundamental diagram, spatiotemporal diagram, and lane-changing frequency were investigated to show the effect of mechanical restriction on heterogeneous traffic flow. It was shown that there would be still three traffic phases in heterogeneous traffic condition; the active deceleration of the heavy truck could well eliminate the plug; the lane-changing frequency was low in synchronized flow; the flow and velocity would decrease as the proportion of heavy truck grows or the limited deceleration capability of heavy truck drops; and the flow could be improved with lane control measures.

  6. Potential Safety Benefit of the Blind Spot Detection System for Large Trucks on the Vulnerable Road Users in Taiwan

    Wang Ming-Hang

    2016-01-01

    Full Text Available Considering motorcyclists, pedestrians and bicyclists as vulnerable road users (VRUs, more than 75 percent of the victims of fatal crashes involving large trucks in Taiwan are VRUs. Most crashes occurred at or were due to the blind spots of large trucks because of the size and traveling locations of the VRUs. This study applies typology and statistical methods to estimate the potential safety benefit of blind spot detection (BSD systems for large trucks on VRUs. The pre-crash scenarios associated with the blind spots of large trucks were derived by counting the maneuvers of large trucks and VRUs, prior to crashes, the truck drivers’ improper behaviors (cause of crashes, and the crash types. The number of crashes and fatalities were counted for the pre-crash scenario relevant to the BSD systems. A value of 0.8 of human machine interface factor (HMIF based on a previous study was applied to estimate the potential safety benefits of the BSD system. The results show that the implementation of BSD systems on all large trucks could help avoid about 24, 10, and 11 percent of large truck-involved crashes with pedestrians, bicycles, and motorcycles, respectively. The BSD systems could also save 5 pedestrians, 3 bicyclists, and 15 motorcyclists per year from crashes involving large trucks.

  7. Graphs as a Visual Aid in English for Special Purposes. Lenguas para objetivos especificos (Languages for Special Purposes), No. 5.

    Stark, Merritt W.; Stark, Kathleen LaPiana

    Visual aids have been developed to strengthen non-English speaking students' ability to speak and write English effectively in their subject areas. Among these aids, graphs have been valuable for economics students because they readily illustrate the nature of the relationship between two sets of numbers. Frequently, the ability to analyze graphs…

  8. Investigation of human body vibration exposures on haul trucks operating at U.S. surface mines/quarries relative to haul truck activity

    Mayton, Alan G.; Porter, William L.; Xu, Xueyan S.; Weston, Eric B.; Rubenstein, Elaine N.

    2018-01-01

    Workers who operate mine haul trucks are exposed to whole-body vibration (WBV) on a routine basis. Researchers from the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) investigated WBV and hand-arm vibration (HAV) exposures for mine/quarry haul truck drivers in relation to the haul truck activities of dumping, loading, and traveling with and without a load. The findings show that WBV measures in weighted root-mean-square accelerations (aw) and vibration dose value (VDV), when compared to the ISO/ANSI and European Directive 2002/44/EC standards, were mostly below the Exposure Action Value (EAV) identified by the health guidance caution zone (HGCZ). Nevertheless, instances were recorded where the Exposure Limit Value (ELV) was exceeded by more than 500 to 600 percent for VDVx and awx, respectively. Researchers determined that these excessive levels occurred during the traveling empty activity, when the haul truck descended down grade into the pit loading area, sliding at times, on a wet and slippery road surface caused by rain and overwatering. WBV levels (not normalized to an 8-h shift) for the four haul truck activities showed mean awz levels for five of the seven drivers exceeding the ISO/ANSI EAV by 9–53 percent for the traveling empty activity. Mean awx and awz levels were generally higher for traveling empty and traveling loaded and lower for loading/dumping activities. HAV for measures taken on the steering wheel and shifter were all below the HGCZ which indicates that HAV is not an issue for these drivers/operators when handling steering and shifting control devices. PMID:29725145

  9. 7 CFR 215.1 - General purpose and scope.

    2010-01-01

    ... 7 Agriculture 4 2010-01-01 2010-01-01 false General purpose and scope. 215.1 Section 215.1... AGRICULTURE CHILD NUTRITION PROGRAMS SPECIAL MILK PROGRAM FOR CHILDREN § 215.1 General purpose and scope. This part announces the policies and prescribes the general regulations with respect to the Special Milk...

  10. 40 CFR 86.085-2 - Definitions.

    2010-07-01

    ... 1977 and Later Model Year New Light-Duty Vehicles, Light-Duty Trucks and Heavy-Duty Engines, and for... standard. PRODLDT represents the manufacturer's total diesel light-duty truck production for those engine... special purpose vehicles such as small dump trucks, and trash compactor trucks. Typical applications would...

  11. A comparison of pipeline versus truck transport of bio-oil.

    Pootakham, Thanyakarn; Kumar, Amit

    2010-01-01

    Biomass-based energy and fuels are receiving attention because they are considered carbon neutral; i.e. the amount of CO(2) released during combustion of this biomass is nearly the same as that taken up by the plants during their growth. Bio-oil is a dark viscous liquid consisting of hydrocarbons. These are produced by fast pyrolysis of biomass. "As-is" biomass material has a low energy density (MJ m(-3)), hence, the cost of transporting this energy is high. Bio-oil has a high energy density as compared to "as-is" biomass material, consequently it helps in reducing the cost of energy transport. This study compares the life cycle assessment of transportation of bio-oil by pipeline with that by truck. The scope of the work includes the transportation of bio-oil by truck or pipeline from a centralized plant (supplied with forest biomass) to an end-user. Two cases are studied for pipeline transport of bio-oil: the first case considers a coal-based electricity supply for pumping the bio-oil through a pipeline; the second case considers an electricity supply from a renewable resource. The two cases of pipeline transport are compared to two cases of truck transport (truck trailer and super B-train truck). The life cycle greenhouse gas (GHG) emissions from the pipeline transport of bio-oil for the two cases of electricity supply are 345 and 17 g of CO(2) m(-3) km(-1), respectively. Similar values for transport by trailer (capacity - 30 m(3)) and super B-train truck (capacity - 60 m(3)) are 89 and 60 g of CO(2) m(-3) km(-1), respectively. Energy input for bio-oil transport is 3.95 MJ m(-3) km(-1) by pipeline, 2.59 MJ m(-3) km(-1) by truck and 1.66 MJ m(-3) km(-1) by super B-train truck. The results show that GHG emissions in pipeline transport are largely dependent on the source of electricity (higher for coal-based electricity). Substituting 250 m(3) day(-1) of pipeline-transported bio-oil for coal-based electricity can mitigate about 5.1 million tonnes of CO(2) per year

  12. Toxoplasma gondii infection in interstate truck drivers: a case-control seroprevalence study.

    Alvarado-Esquivel, Cosme; Pacheco-Vega, Sandy Janet; Hernández-Tinoco, Jesús; Salcedo-Jáquez, Misael; Sánchez-Anguiano, Luis Francisco; Berumen-Segovia, Luis Omar; Rábago-Sánchez, Elizabeth; Liesenfeld, Oliver

    2015-02-05

    Infection with Toxoplasma gondii can be acquired via the ingestion of undercooked or raw meat containing tissue cysts, or via ingestion of water contaminated with oocysts. Professional long distance truck driving may have epidemiological importance for food-borne infections since drivers eat out of home and in places where hygiene and cooking practices are uncertain. We aimed to determine whether interstate truck drivers in Durango, Mexico have an increased risk of infection with T. gondii as indicated by seropositivity; and to determine the socio-demographic, work, clinical, and behavioral characteristics associated with T. gondii seropositivity in interstate truck drivers. Through a case-control study design, 192 truck drivers and 192 controls from the general population of the same region matched by gender and age were examined with enzyme-linked immunoassays for the presence of anti-Toxoplasma IgG and IgM antibodies. Socio-demographic, work, clinical and behavioral characteristics from the truck drivers were obtained. Anti-T. gondii IgG antibodies were found in 23 (12.0%) of 192 truck drivers and in 13 (6.8%) of 192 controls (OR = 21.0; 95% CI: 1.23-358.38; P = 0.002). Anti-T. gondii IgM antibodies were found in 7 (3.6%) cases and in 7 (3.6%) controls (P = 1.00). The seroprevalence of T. gondii infection was higher in drivers with reflex impairment than in those without this impairment (4/13, 30.8% vs 19/179, 10.6%, respectively; P = 0.05), and in drivers with hearing impairment than in those without this impairment (3/7, 42.9% vs 20/185, 10.8%, respectively; P = 0.03). Multivariate analysis of work and behavioral characteristics of truck drives showed positive associations of T. gondii exposure with trips to the south of Mexico (OR = 3.11; 95% CI: 1.02-9.44; P = 0.04) and consumption of horse meat (OR = 5.18; 95% CI: 1.62-16.55; P = 0.005). Results suggest that interstate truck drivers may have an increased risk for T

  13. Effects of After-Treatment Control Technologies on Heavy-Duty Diesel Truck Emissions

    Preble, C.; Dallmann, T. R.; Kreisberg, N. M.; Hering, S. V.; Harley, R.; Kirchstetter, T.

    2015-12-01

    Diesel engines are major emitters of nitrogen oxides (NOx) and the black carbon (BC) fraction of particulate matter (PM). Diesel particle filter (DPF) and selective catalytic reduction (SCR) emission control systems that target exhaust PM and NOx have recently become standard on new heavy-duty diesel trucks (HDDT). There is concern that DPFs may increase ultrafine particle (UFP) and total particle number (PN) emissions while reducing PM mass emissions. Also, the deliberate catalytic oxidation of engine-out NO to NO2 in continuously regenerating DPFs may lead to increased tailpipe emission of NO2 and near-roadway concentrations that exceed the 1-hr national ambient air quality standard. Increased NO2 emissions can also promote formation of ozone and secondary PM. We report results from ongoing on-road studies of HDDT emissions at the Port of Oakland and the Caldecott Tunnel in California's San Francisco Bay Area. Emission factors (g pollutant per kg diesel) were linked via recorded license plates to each truck's engine model year and installed emission controls. At both sites, DPF use significantly increased the NO2/NOx emission ratio. DPFs also significantly increased NO2 emissions when installed as retrofits on older trucks with higher baseline NOx emissions. While SCR systems on new trucks effectively reduce total NOx emissions and mitigate these undesirable DPF-related NO2 emissions, they also lead to significant emission of N2O, a potent greenhouse gas. When expressed on a CO2-equivalent basis, the N2O emissions increase offsets the fuel economy gain (i.e., the CO2 emission reduction) associated with SCR use. At the Port, average NOx, BC and PN emission factors from new trucks equipped with DPF and SCR were 69 ± 15%, 92 ± 32% and 66 ± 35% lower, respectively, than modern trucks without these emission controls. In contrast, at the Tunnel, PN emissions from older trucks retrofit with DPFs were ~2 times greater than modern trucks without DPFs. The difference

  14. Prediction of fuel consumption of mining dump trucks: A neural networks approach

    Siami-Irdemoosa, Elnaz; Dindarloo, Saeid R.

    2015-01-01

    Highlights: • A neural network model of fuel consumption in mining haul trucks was constructed and tested. • Using the cyclic activities, the model was able to predict unseen (testing) data. • Trucks idle times were identified as the most important unnecessary energy consuming portion of the network. • Practical remedies, based on the nature of mining operations, were proposed to reduce the energy consumption. - Abstract: Fuel consumption of mining dump trucks accounts for about 30% of total energy use in surface mines. Moreover, a fleet of large dump trucks is the main source of greenhouse gas (GHG) generation. Modeling and prediction of fuel consumption per cycle is a valuable tool in assessing both energy costs and the resulting GHG generation. However, only a few studies have been published on fuel prediction in mining operations. In this paper, fuel consumption per cycle of operation was predicted using artificial neural networks (ANN) technique. Explanatory variables were: pay load, loading time, idled while loaded, loaded travel time, empty travel time, and idled while empty. The output variable was the amount of fuel consumed in one cycle. Mean absolute percentage error (MAPE) of 10% demonstrated applicability of ANN in prediction of the fuel consumption. The results demonstrated the considerable effect of mining trucks idle times in fuel consumption. A large portion of the unnecessary energy consumption and GHG generation, in this study, was solely due to avoidable idle times. This necessitates implementation of proper actions/remedies in form of both preventive and corrective actions

  15. Radio Frequency Identification (RFID) and communication technologies for solid waste bin and truck monitoring system.

    Hannan, M A; Arebey, Maher; Begum, R A; Basri, Hassan

    2011-12-01

    This paper deals with a system of integration of Radio Frequency Identification (RFID) and communication technologies for solid waste bin and truck monitoring system. RFID, GPS, GPRS and GIS along with camera technologies have been integrated and developed the bin and truck intelligent monitoring system. A new kind of integrated theoretical framework, hardware architecture and interface algorithm has been introduced between the technologies for the successful implementation of the proposed system. In this system, bin and truck database have been developed such a way that the information of bin and truck ID, date and time of waste collection, bin status, amount of waste and bin and truck GPS coordinates etc. are complied and stored for monitoring and management activities. The results showed that the real-time image processing, histogram analysis, waste estimation and other bin information have been displayed in the GUI of the monitoring system. The real-time test and experimental results showed that the performance of the developed system was stable and satisfied the monitoring system with high practicability and validity. Copyright © 2011 Elsevier Ltd. All rights reserved.

  16. Six Reasons why hours of service regulations for truck drivers are violated

    Grøn, Sisse

    2008-01-01

      ABSTRACT Two decades of research has established a correlation between tiredness and fatigue, and traffic accident involving truck drivers.  Regulations limiting the driving hours of truck drivers thus are necessary precautions. But compliance is a problem. The answer from authorities tend to b...... independency ideal among truck drivers. The last reason is that the drivers and their employers share an interest in long work hours.......  ABSTRACT Two decades of research has established a correlation between tiredness and fatigue, and traffic accident involving truck drivers.  Regulations limiting the driving hours of truck drivers thus are necessary precautions. But compliance is a problem. The answer from authorities tend...... is that the regulation seems to be designed to long distance driving, and has some short-comings when applied to short distance drivers. The third reason is that the regulation deprives the drivers of means to control their tiredness. The fourth reason is that the regulation limits room for planning ahead generally...

  17. Special protective concretes

    Bouniol, P.

    2001-01-01

    Concrete is the most convenient material when large-scale radiation protection is needed. Thus, special concretes for nuclear purposes are used in various facilities like reactors, reprocessing centers, storage sites, accelerators, hospitals with nuclear medicine equipment, food ionization centers etc.. The recent advances made in civil engineering for the improvement of concrete durability and compactness are for a large part transposable to protection concretes. This article presents the basic knowledge about protection concretes with the associated typological and technological aspects. A large part is devoted to the intrinsic properties of concretes and to their behaviour in irradiation and temperature conditions: 1 - definition and field of application of special protective concretes; 2 - evolution of concepts and technologies (durability of structures, techniques of formulation, new additives, market evolution); 3 - design of protective structures (preliminary study, radiation characteristics, thermal constraints, damping and dimensioning, mechanical criteria); 4 - formulation of special concretes (general principles, granulates, hydraulic binders, pulverulent additives, water/cement ratio, reference composition of some special concretes); 5 - properties of special concretes (damping and thermo-mechanical properties); 6 - induced-irradiation and temperature phenomena (activation, radiolysis, mineralogical transformations, drying, shrinking, creep, corrosion of reinforcement). (J.S.)

  18. Prilog ispitivanju korištenja instrumentarija različitih tehničkih izvedbi pri uspostavljanju nivelmanskih mreža posebnih namjena u inženjerskoj geodeziji : Contribution on study possibilities in using instruments of different technical performances in establishing special purposes leveling networks in engineering geodesy

    Nihad Kapetanović

    2015-12-01

    Full Text Available Ispitivanje mogućnosti korištenja geodetskih instrumenata sličnih tehničkih karakteristika, ali različitih tehničkih izvedbi je uvijek zanimljiva geodetska tema. Osnovna svrha ovog istraživanja je analiziranje tačnosti testne nivelmanske mreže, unutar koje su visinske razlike izmjerene nivelirima Koni 007CZJ i Leica DNA 03. Rezultati dobiveni na kraju istraživanja pokazali su da oba nivelira zadovoljavaju kriterije preciznog nivelmana, ali se prednost daje niveliru DNA 03. : Examination of possibilities in using geodetic (survey instruments of the same specifications, but different technical performances is always an interesting geodetic topic. The main purpose of this research is to analyze the accuracy of special purposes leveling networks where height differences were measured with Koni 007 CZJ and Leica DNA 03 levels. Obtained results showed that both leveling results fulfill the required conditions of precision leveling, but the preference is given to level DNA 03.

  19. International Specialization

    Kleindienst, Ingo; Geisler Asmussen, Christian; Hutzschenreuter, Thomas

    2012-01-01

    Whether and how international diversification and cross-border arbitrage affects firm performance remains one of the major unresolved research questions in the strategy and international business literatures. We propose that knowing how much a firm has internationally diversified tells us very...... little about performance implications, if we do not know, and do not ask, how the firm has diversified. Therefore, building on the two broad arguments of operating flexibility and location-specific commitment, we develop a theoretical framework that focuses on the extent to which a firm's international...... arbitrage strategy is characterized by specialization versus replication and argue that these different strategies may have differential impact on profitability and risk reduction. Developing a sophisticated measure of international specialization and using a unique panel data set of 92 German MNEs to test...

  20. Special offer

    Staff Association

    2010-01-01

    Special offer for members of the Staff Association and their families 10% reduction on all products in the SEPHORA shop (sells perfume, beauty products etc.) in Val Thoiry ALL YEAR ROUND. Plus 20% reduction during their “vente privée”* three or four times a year. Simply present your Staff Association membership card when you make your purchase. * next “vente privée” from 24th to 29th May 2010  

  1. Special lecture

    Yoshikawa, H.

    1998-01-01

    In his special lecture, given at the Artsimovich-Kadomtsev Memorial Session of the 17th IAEA Fusion Energy Conference in Yokohama, October 1998, Prof. H. Yoshikawa stated that the fusion program had come to a crossroads. He was wondering whether the future would lead to cooperation between nations, striving to overcome the difficulties the world is confronted with, or if it would lead to despair

  2. Special offer

    Staff Association

    2011-01-01

    SPECIAL OFFER FOR OUR MEMBERS Tarif unique Adulte/Enfant Entrée Zone terrestre 19 euros instead of 23 euros Entrée “Zone terrestre + aquatique” 24 euros instead of 31 euros Free for children under 3, with limited access to the attractions. Walibi Rhône-Alpes is open daily from 22 June to 31 August, and every week end from 3 September until 31 October. Closing of the “zone aquatique” 11 September.

  3. Special effects.

    Davis, Carol

    The nursing team on the day case ward at Alder Hey Hospital has introduced changes to the environment to help children with special needs, who often attend the ward repeatedly. Small changes, such as keeping colours on the ward neutral, can help children relax. Nurses contact parents a week before admission to find out about their child's likes and dislikes. Parents are encouraged to bring a child's favourite items with them. Operating sessions are scheduled to meet these children's needs.

  4. Experimental study on transportation safety of package in side collision of heavy duty truck

    Suga, M.; Sasaki, T.

    1989-01-01

    The accidents in road transportation of package may be collision, fall and fire. It is necessary to examine all cases very carefully because collision might be caused by other vehicle. Collisions are classified into head-on collision, rear-end collision, side collision. A lot of experiments and analyses are reported on head-on collision, so the behavior of vehicle and package may be predicted without difficulty. Rear-end collisions bring about less impact and may be applied corresponding to the head-on collisions. About side collisions, few experiments or analyses are reported, and most of them are about passenger cars not about trucks. So it becomes important to study the transportation safety of package carried on a heavy duty truck when hit on the side by another truck similar in size

  5. STRESS LOADING SIMULATION OF HYDRO-MECHANICAL TRANSMISSION OF DUMP TRUCK

    S. A. Sidorov

    2006-01-01

    Full Text Available The Transmission model and software package to investigate stress loading of a hydromechanical transmission of a dump truck have been developed. The given software package allows to model stress loading of transmission gears in taking-off and acceleration modes at various road resistance, positions of an engine control pedal and initial revolutions of an engine crankshaft, various laws of friction clutch switching and some other parameters that permit to reveal a rate of various operational mode influence on stress loading of a dump truck transmission. An equivalence of the developed software is proved by the comparison of the experimentally obtained stress loading process of the hydro-mechanical transmission of a BelAZ- 7555 dump truck with the results of the simulation 

  6. Health Promotion at the Construction Work Site: The Lunch Truck Pilot Study.

    Caban-Martinez, Alberto J; Moore, Kevin J; Clarke, Tainya C; Davila, Evelyn P; Clark, John D; Lee, David J; Fleming, Lora E

    2018-04-01

    The transient nature of construction work makes it difficult to conduct longitudinal worksite-based health promotion activities. As part of a workplace health assessment pilot study, we worked with a commercial lunch truck company to disseminate four types of health education materials including cancer screening, workplace injury prevention, fruit and vegetable consumption, and smoking cessation to construction workers purchasing food items from the truck during their job breaks. Two weeks following the worksite assessment, we followed up with these workers to ascertain their use of the health promotion materials. Of the 54 workers surveyed, 83% reported reviewing and sharing the cancer screening materials with their families, whereas 44% discussed the cancer screening materials with coworkers. Similar proportions of workers reviewed, shared, and discussed the other health promotion materials with their family. Lunch trucks may be an effective strategy and delivery method for educating construction workers on healthy behaviors and injury prevention practices.

  7. Air-cushion vehicles as an alternative to conventional industrial trucks

    Marr, E.

    2003-01-01

    Protective shieldings must be used for the transportation of radioactive materials, such as drums and containers within the control area, in order to observe the activity classes of the rooms. As a result of the change in the radiation protection ordinance, the operating areas of the floor conveyors have to be protected even more, i.e. transportation weights are becoming even bigger. When using pallet lift trucks without drive, weights over 2 tons are virtually unable to be operated. A fork-lift truck must be used for higher loads. If the transportation weight (transportation load and net weight of the lift truck) is doubled, usage within buildings is very restricted through the ceiling net load. This is the range of application of air cushion vehicles, in particular if positioning accuracy and remote-controlled driving become necessary. (orig.)

  8. Electro-deposition painting process improvement of cab truck by Six Sigma concept

    Kawitu, Kitiya; Chutima, Parames

    2017-06-01

    The case study company is a manufacturer of trucks and currently facing a high rework cost due to the thickness of the electro-deposited paint (EDP) of the truck cab is lower than standard. In addition, the process capability is very low. The Six Sigma concept consisting of 5 phases (DMAIC) is applied to determine new parameter settings for each significant controllable factor. After the improvement, EDP thickness of the truck cab increases from 17.88μ to 20μ (i.e. standard = 20 ± 3μ). Moreover, the process capability indexes (Cp and Cpk) are increased from 0.9 to 1.43, and from 0.27 to 1.43, respectively. This improvement could save the rework cost about 1.6M THB per year.

  9. Measurement of stress distributions in truck tyre contact patch in real rolling conditions

    Anghelache, Gabriel; Moisescu, Raluca

    2012-12-01

    Stress distributions on three orthogonal directions have been measured across the contact patch of truck tyres using the complex measuring system that contains a transducer assembly with 30 sensing elements placed in the road surface. The measurements have been performed in straight line, in real rolling conditions. Software applications for calibration, data acquisition, and data processing were developed. The influence of changes in inflation pressure and rolling speed on the shapes and sizes of truck tyre contact patch has been shown. The shapes and magnitudes of normal, longitudinal, and lateral stress distributions, measured at low speed, have been presented and commented. The effect of wheel toe-in and camber on the stress distribution results was observed. The paper highlights the impact of the longitudinal tread ribs on the shear stress distributions. The ratios of stress distributions in the truck tyre contact patch have been computed and discussed.

  10. FedEx Gasoline Hybrid Electric Delivery Truck Evaluation: 6-Month Interim Report

    Barnitt, R.

    2010-05-01

    This interim report presents partial (six months) results for a technology evaluation of gasoline hybrid electric parcel delivery trucks operated by FedEx in and around Los Angeles, CA. A 12 month in-use technology evaluation comparing in-use fuel economy and maintenance costs of GHEVs and comparative diesel parcel delivery trucks was started in April 2009. Comparison data was collected and analyzed for in-use fuel economy and fuel costs, maintenance costs, total operating costs, and vehicle uptime. In addition, this interim report presents results of parcel delivery drive cycle collection and analysis activities as well as emissions and fuel economy results of chassis dynamometer testing of a gHEV and a comparative diesel truck at the National Renewable Energy Laboratory's (NREL) ReFUEL laboratory. A final report will be issued when 12 months of in-use data have been collected and analyzed.

  11. An exploration study to find important factors in market entrance: A case study of truck industry

    Zoheir Khodamoradi

    2013-09-01

    Full Text Available This paper presents an empirical investigation to find important factors influencing market penetration in truck industry. The proposed study designs a questionnaire in Likert scale consists of 51 questions, distributes it among 300 people who worked for different truck industry related units and collects 262 filled ones. Cronbach alpha is calculated as 0.89. In addition, Kaiser-Meyer-Olkin Measure of Sampling Adequacy and Approx. Chi-Square are 0.845 and 3067.443, respectively. The study has implemented principal component analysis and the results have indicated that there were eight factors influencing entering truck making industry including adaptation strategies, new ideas, cost competitiveness, product capabilities, market characteristics, competition threats from external market environment and export accelerators.

  12. Improvement of the mining technology with the ring movement scheme of the haul trucks

    Slobodyanyuk R.V.

    2016-04-01

    Full Text Available The article describes the designed technology that allows to expand the use of the haul truck ring movement scheme and to reduce the share of an empty run time in the transportation cycle. A preliminary calculation of the efficiency of its usage has allowed to confirm the main advantages of this scheme over the existing one as follows: reducing the required number of transport for the needs of open-pit mine operation by increasing the productivity of mining trucks; decreasing the transport operating costs (some part of an empty truck movement occurs when the engine is switched off; dropping the probability of accidents (reduced a number of the counter transport maneuvers. The calculation showed the regularity of changes in the efficiency using the alternative scheme in relation to the basic one, which reflecting significantly higher effectiveness in situations with a smaller distance between the empty run sites of the ring scheme.

  13. Social Cognitive Antecedents of Fruit and Vegetable Consumption in Truck Drivers: A Sequential Mediation Analysis.

    Hamilton, Kyra; Vayro, Caitlin; Schwarzer, Ralf

    2015-01-01

    To examine a mechanism by which social cognitive factors may predict fruit and vegetable consumption in long-haul truck drivers. Dietary self-efficacy, positive outcome expectancies, and intentions were assessed in 148 Australian truck drivers, and 1 week later they reported their fruit and vegetable consumption. A theory-guided sequential mediation model was specified that postulated self-efficacy and intention as mediators between outcome expectancies and behavior. The hypothesized model was confirmed. A direct effect of outcome expectancies was no longer present when mediators were included, and all indirect effects were significant, including the 2-mediator chain (β = .15; P role of outcome expectancies and self-efficacy are important to consider for understanding and predicting healthy eating intentions in truck drivers. Copyright © 2015 Society for Nutrition Education and Behavior. Published by Elsevier Inc. All rights reserved.

  14. The determinants of fuel use in the trucking industry – volume, size and the rebound effect

    Mulalic, Ismir

    2011-01-01

    We analyse the determinants of trucking firm fuel use. We develop a simple model to show that trucking firm fuel use depends, in addition to the fuel price and the traffic volume, also on the output of the trucking firm’s production process (the movement of cargo) measured in tonkilometres...... these elasticities using a simultaneous-equation model based on aggregate time-series data for Denmark for 1980-2007. Our best estimates of the short run and the long run rebound effects for road freight transportation are 19% and 28%, respectively. We also find that an increase in the fuel price surprisingly has...... a small but significant negative effect on the fuel efficiency (measured here as vehicle kilometres travelled (VKT) per litre of consumed fuel), i.e. a 1% increase in the fuel price decreases the fuel efficiency by 0.13% in the long run. However, less distance has to be driven for the same payload. An 1...

  15. On the road again: concurrency and condom use among Uganda truck drivers.

    Costenbader, Elizabeth C; Lancaster, Kathryn; Bufumbo, Leonard; Akol, Angela; Guest, Greg

    2015-01-01

    Long-distance truck drivers have been shown to be a critical population in the spread of HIV in Africa. In 2009, surveys with 385 Ugandan long-distance truck drivers measured concurrency point prevalence with two methods; it ranged from 37.4% (calendar-method) to 50.1% (direct question). The majority (84%) of relationships reported were long-term resulting in a long duration of overlap (average of 58 months) across concurrent partnerships. Only 7% of these men reported using any condoms with their spouses during the past month. Among all non-spousal relationships, duration of relationship was the factor most strongly associated with engaging in unprotected sex in the past month in a multivariable analyses controlling for partner and relationship characteristics. Innovative intervention programs for these men and their partners are needed that address the realities of truck drivers' lifestyles.

  16. Risk of transporting plutonium dioxide and liquid plutonium nitrate by truck and rail

    Williams, L.D.; Hall, R.J.

    1976-07-01

    Results are summarized of the risk assessments of shipping PuO 2 powder and liquid Pu nitrate by truck and rail in the U.S. In the analysis method used, the system is described, potential release sequences are identified and evaluated (fault tree used), and the system risk is assessed. It is concluded that: there is little difference in risk in shipping PuO 2 by rail and by truck; there also is little change in risk in shipping PuO 2 by rail and by truck; there also is little change in risk for liquid shipment; the vermiculite loss is somewhat less important in rail shipment; and the response of the L-10 container to crush is more important in rail transport

  17. Understanding commercial truck drivers' decision-makin process concerning distracted driving.

    Swedler, David I; Pollack, Keshia M; Gielen, Andrea C

    2015-05-01

    A concurrent mixed methods design was used to explore personal and workplace factors, informed by the Theory of Planned Behavior, that affect truck drivers' decision-making about distracted driving on the job. Qualitative data were collected via semi-structured interviews with experts in truck safety and distracted driving, and quantitative data were collected via online survey of truck drivers in the United States. Findings from the interviews illustrated how drivers perceived distractions and the importance of supervisors enforcing organizational distracted driving policies. Survey results found that behavioral intentions were most important in regards to texting and crash and near-crash outcomes, while perceived norms from management best described the correlation between dispatch device use and negative crash-related outcomes. By using a mixed methods design, rather than two separate studies, these findings revealed nuanced differences into the influence of supervisors on distracted driving. Copyright © 2015 Elsevier Ltd. All rights reserved.

  18. A comprehensive analysis of factors influencing the injury severity of large-truck crashes.

    Zhu, Xiaoyu; Srinivasan, Sivaramakrishnan

    2011-01-01

    Given the importance of trucking to the economic well being of a country and the safety concerns posed by the trucks, a study of large-truck crashes is critical. This paper contributes by undertaking an extensive analysis of the empirical factors affecting injury severity of large-truck crashes. Data from a recent, nationally representative sample of large-truck crashes are examined to determine the factors affecting the overall injury severity of these crashes. The explanatory factors include the characteristics of the crash, vehicle(s), and the driver(s). The injury severity was modeled using two measures. Several similarities and some differences were observed across the two models which underscore the need for improved accuracy in the assessment of injury severity of crashes. The estimated models capture the marginal effects of a variety of explanatory factors simultaneously. In particular, the models indicate the impacts of several driver behavior variables on the severity of the crashes, after controlling for a variety of other factors. For example, driver distraction (truck drivers), alcohol use (car drivers), and emotional factors (car drivers) are found to be associated with higher severity crashes. A further interesting finding is the strong statistical significance of several dummy variables that indicate missing data - these reflect how the nature of the crash itself could affect the completeness of the data. Future efforts should seek to collect such data more comprehensively so that the true effects of these aspects on the crash severity can be determined. Copyright © 2010 Elsevier Ltd. All rights reserved.

  19. The impacts of multiple rest-break periods on commercial truck driver's crash risk.

    Chen, Chen; Xie, Yuanchang

    2014-02-01

    Driver fatigue has been a major contributing factor to fatal commercial truck crashes, which accounted for about 10% of all fatal motor vehicle crashes that happened between 2009 and 2011. Commercial truck drivers' safety performance can deteriorate easily due to fatigue caused by long driving hours and irregular working schedules. To ensure safety, truck drivers often use off-duty time and short rest breaks during a trip to recover from fatigue. This study thoroughly investigates the impacts of off-duty time prior to a trip and short rest breaks on commercial truck safety by using Cox proportional hazards model and Andersen-Gill model. It is found that increasing total rest-break duration can consistently reduce fatigue-related crash risk. Similarly, taking more rest breaks can help to reduce crash risk. The results suggest that two rest breaks are generally considered enough for a 10-hour trip, as three or more rest breaks may not further reduce crash risk substantially. Also, the length of each rest break does not need to be very long and 30min is usually adequate. In addition, this study investigates the safety impacts of when to take rest breaks. It is found that taking rest breaks too soon after a trip starts will cause the rest breaks to be less effective. The findings of this research can help policy makers and trucking companies better understand the impacts of multiple rest-break periods and develop more effective rules to improve the safety of truck drivers. Copyright © 2014 Elsevier Ltd and National Safety Council. All rights reserved.

  20. Influences on Energy Savings of Heavy Trucks Using Cooperative Adaptive Cruise Control

    Lammert, Michael P [National Renewable Energy Laboratory (NREL), Golden, CO (United States); McAuliffe, Brian [National Research Council Canada; Lu, Xiao-Yun [University of California-Berkeley; Shladover, Steven [University of California-Berkeley; Surcel, Marius-Dorin [FPInnovations; Kailas, Aravind [Volvo Group

    2018-04-03

    An integrated adaptive cruise control (ACC) and cooperative ACC (CACC) was implemented and tested on three heavy-duty tractor-trailer trucks on a closed test track. The first truck was always in ACC mode, and the followers were in CACC mode using wireless vehicle-vehicle communication to augment their radar sensor data to enable safe and accurate vehicle following at short gaps. The fuel consumption for each truck in the CACC string was measured using the SAE J1321 procedure while travelling at 65 mph and loaded to a gross weight of 65,000 lb, demonstrating the effects of: inter-vehicle gaps (ranging from 3.0 s or 87 m to 0.14 s or 4 m, covering a much wider range than previously reported tests), cut-in and cut-out maneuvers by other vehicles, speed variations, the use of mismatched vehicles (standard trailers mixed with aerodynamic trailers with boat tails and side skirts), and the presence of a passenger vehicle ahead of the platoon. The results showed that energy savings generally increased in a non-linear fashion as the gap was reduced. The middle truck saved the most fuel at gaps shorter than 12 m and the trailing truck saved the most at longer gaps, while lead truck saved the least at all gaps. The cut-in and cut-out maneuvers had only a marginal effect on fuel consumption even when repeated every two miles. The presence of passenger-vehicle traffic had a measurable impact. The fuel-consumption savings on the curves was less than on the straight sections.

  1. TruckWeight wireless onboard scale helps oilfield services fleet find profit, compliance

    Anon.

    2007-05-15

    This article presented a wireless scale that measures temperature and pressure changes in a vehicle's air suspension. The instrument is being used by Alberta-based Rusch Inc., an operator of tank trucks and pup trailers which haul potassium chloride solution, methanol, frac oil, crude oil and other fluids. Made by TruckWeight Inc., the Smart Scale relays data to a handheld receiver using a low-powered safe radio transmitter. It is designed so its power output is not high enough to ignite gases in the atmosphere near wellheads. The information from the Smart Scale is interpreted by a small computer in a handheld receiver. The axle weight and gross vehicle weight measurement is accurate to within 150 pounds. Rusch trucks operate on steep grades all year, encountering soft ground in the summer, and frozen terrain in the winter. When loading is done in the bush, it is impossible to reliably weigh the trucks, whose licensed gross combination weight is 51,300 kilograms. In Alberta, an overweight fine can trigger an audit of a company's safety record and operating practices. Running overweight also places stress on axles, suspensions, wheel-end components tires and brakes. Therefore, adhering to the rated weight is essential. In 2006, Rusch Inc. installed the Smart Scale wireless on-board scale for trucks, tractors and trailers with air suspension. The scale includes a sensor with an integrated antenna and DOT fittings for the vehicle's airline. While the truck is being loaded, the scale produces readings every 3 seconds. This maintenance-free instrument is accurate in temperature extremes ranging from -40 F to 158 F and uses common AA batteries. It is waterproof, weatherproof, shock resistant and non-corrosive. The cost to equip a tractor and trailer with a Smart Scale is $1,590 US, half the cost of a hard-wired scale. 5 figs.

  2. Commercial truck crash injury severity analysis using gradient boosting data mining model.

    Zheng, Zijian; Lu, Pan; Lantz, Brenda

    2018-06-01

    Truck crashes contribute to a large number of injuries and fatalities. This study seeks to identify the contributing factors affecting truck crash severity using 2010 to 2016 North Dakota and Colorado crash data provided by the Federal Motor Carrier Safety Administration. To fulfill a gap of previous studies, broad considerations of company and driver characteristics, such as company size and driver's license class, along with vehicle types and crash characteristics are researched. Gradient boosting, a data mining technique, is applied to comprehensively analyze the relationship between crash severities and a set of heterogeneous risk factors. Twenty five variables were tested and 22 of them are identified as significant variables contributing to injury severities, however, top 11 variables account for more than 80% of injury forecasting. The relative variable importance analysis is conducted and furthermore marginal effects of all contributing factors are also illustrated in this research. Several factors such as trucking company attributes (e.g., company size), safety inspection values, trucking company commerce status (e.g., interstate or intrastate), time of day, driver's age, first harmful events, and registration condition are found to be significantly associated with crash injury severity. Even though most of the identified contributing factors are significant for all four levels of crash severity, their relative importance and marginal effect are all different. For the first time, trucking company and driver characteristics are proved to have significant impact on truck crash injury severity. Some of the results in this study reinforce previous studies' conclusions. Findings in this study can be helpful for transportation agencies to reduce injury severity, and develop efficient strategies to improve safety. Copyright © 2018 National Safety Council and Elsevier Ltd. All rights reserved.

  3. 46 CFR 169.101 - Purpose.

    2010-10-01

    ..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS General Provisions § 169.101 Purpose. The regulations in this part set forth uniform requirements which are suited to the particular characteristics and specialized operations of sailing school vessels as defined in Title 46...

  4. Single-purpose nuclear medicine instruments

    Boucek, J.

    Nuclear medicine requires the most up-to-date specialized technical facilities. The paper underlines the factor of reliability in purpose-designed equipment used for basic examinations. The possibility is also discussed of the automation of standard nuclear medicine instruments

  5. 78 FR 33860 - Crawler, Locomotive, and Truck Cranes Standard; Extension of the Office of Management and Budget...

    2013-06-05

    ...] Crawler, Locomotive, and Truck Cranes Standard; Extension of the Office of Management and Budget's (OMB... collection requirements contained in the General Industry Standard on Crawler, Locomotive, and Truck cranes... workers from using unsafe cranes and ropes, thereby reducing their risk of death or serious injury caused...

  6. 75 FR 20005 - Crawler, Locomotive, and Truck Cranes Standard; Extension of the Office of Management and Budget...

    2010-04-16

    ...] Crawler, Locomotive, and Truck Cranes Standard; Extension of the Office of Management and Budget's (OMB... Crawler, Locomotive, and Truck Cranes Standard (29 CFR 1910.180). DATES: Comments must be submitted... of each of these requirements is to prevent workers from using unsafe cranes and ropes, thereby...

  7. 78 FR 15714 - Welch Motel, Inc., Welch Oil, Inc., Boondocks USA Truck Stop, Bob Welch v. Midland Power...

    2013-03-12

    ..., Inc., Welch Oil, Inc., Boondocks USA Truck Stop, Bob Welch v. Midland Power Cooperative, Corn Belt..., Welch Motel, Inc., Welch Oil, Inc., Boondocks USA Truck Stop, and Bob Welch (collectively, Complainants... into a contract to consume all of the electric energy and capacity generated by [[Page 15715...

  8. 9 CFR 325.17 - Loading or unloading products in sealed railroad cars, trucks, etc., en route prohibited; exception.

    2010-01-01

    ... sealed railroad cars, trucks, etc., en route prohibited; exception. 325.17 Section 325.17 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE AGENCY ORGANIZATION AND... TRANSPORTATION § 325.17 Loading or unloading products in sealed railroad cars, trucks, etc., en route prohibited...

  9. 9 CFR 316.14 - Marking tank cars and tank trucks used in transportation of edible products.

    2010-01-01

    ... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Marking tank cars and tank trucks used in transportation of edible products. 316.14 Section 316.14 Animals and Animal Products FOOD SAFETY... CONTAINERS § 316.14 Marking tank cars and tank trucks used in transportation of edible products. Each tank...

  10. Total Weight and Axle Loads of Truck Units in the Transport of Timber Depending on the Timber Cargo

    Grzegorz Trzciński

    2018-03-01

    Full Text Available When transporting timber, the high variability of species, assortments and moisture content of the wood raw material does not allow the weight of the transported timber to be precisely determined. This often contributes to the excessive weight loading of the entire truck unit. The aim of the research is to present the variability of the total weight of truck units with wood cargoes (GVW—gross vehicle weight depending on the weight of the empty unit and the transported timber load, as well as to analyze the changes in GVW, unit loads of wood and load on individual truck unit axles depending on the season. This study analyzes the total weight of truck units for 376 transports of Scots pine timber at different times of the year. The total weight of the truck units depends on the weight of an empty unit and the weight of the load. GVW was determined by using a weighbridge to weigh the vehicles and then the empty unit after unloading. The weight of the load was obtained as the difference between GVW and the tare. It was found that GVW differed significantly depending on the truck unit used, ranging from 43.60–58.80 Mg, often exceeding permissible limits for public roads. The individual axle loads for various truck units were also analyzed. The obtained results indicate that these loads are more equally distributed in the case of five-axle trucks compared to six-axle ones.

  11. 3 CFR - Imports of Certain Passenger Vehicle and Light Truck Tires From the People's Republic of China

    2010-01-01

    ... vehicle and light truck tires from the People's Republic of China (China) are being imported into the... 3 The President 1 2010-01-01 2010-01-01 false Imports of Certain Passenger Vehicle and Light Truck... Presidential Determination No. 2009-28 of September 11, 2009 Imports of Certain Passenger Vehicle and Light...

  12. How long-distance truck drivers and villagers in rural southeastern Tanzania think about heterosexual anal sex: a qualitative study

    Mtenga, S.; Shamba, D.; Wamoyi, J.; Kakoko, D.; Haafkens, J.; Mongi, A.; Kapiga, S.; Geubbels, E.

    2015-01-01

    To explore ideas of truck drivers and villagers from rural Tanzania about heterosexual anal sex (HAS) and the associated health risks. Qualitative study using 8 in-depth interviews (IDIs) and 2 focus group discussions (FGDs) with truck drivers and 16 IDIs and 4 FGDs with villagers from the Morogoro

  13. How long-distance truck drivers and villagers in rural southeastern Tanzania think about heterosexual anal sex: a qualitative study

    Mtenga, S.; Shamba, D.; Wamoyi, J.; Kakoko, D.; Haafkens, J.; Mongi, A.; Kapiga, S.; Geubbels, E.

    2015-01-01

    Objective: To explore ideas of truck drivers and villagers from rural Tanzania about heterosexual anal sex (HAS) and the associated health risks. Methods: Qualitative study using 8 in-depth interviews (IDIs) and 2 focus group discussions (FGDs) with truck drivers and 16 IDIs and 4 FGDs with

  14. 75 FR 38168 - Federal Motor Vehicle Theft Prevention Standard; Final Listing of 2011 Light Duty Truck Lines...

    2010-07-01

    ... Theft Prevention Standard; Final Listing of 2011 Light Duty Truck Lines Subject to the Requirements of... light-duty truck lines subject to the requirements of the Federal motor vehicle theft prevention... exemption from the parts marking requirements of the Theft Prevention Standard for the Jaguar XJ vehicle...

  15. North American Free Trade Agreement : coordinated operational plan needed to ensure Mexican trucks' compliance with U.S. standards

    2001-12-01

    In response to concerns about the safety of Mexican trucks, the General Accounting Office (GAO) was asked to examine (1) the extent to which Mexican-domiciled commercial trucks are likely to travel beyond U.S. border commercial zones once the border ...

  16. Opportunities to Investigate the Steering System for Improvement of Truck Driving Properties under Critical Road Conditions

    Gidlewski, Mirosław

    2011-09-01

    Application of an electric steering system in a truck gives new opportunities to obtain desirable and safe motion path under critical road conditions. Analysis of the opportunity to take advantage of the steering system for improvement of truck driving properties will be carried out on the basis of the results of model tests. The paper describes model of the vehicle applied in simulation tests and methodology as well as anticipated results. The scheduled tests will be carried out within the framework of an research project No. NN509 568439 headed by the author.

  17. Structural safety evaluation of the K Basin railcar and truck applications

    Winkel, B.V.

    1995-08-01

    There are two rail spurs in the storage/transfer areas of both the K East and K West fuel storage basins. These rail spurs both end at the west edge of the basins. To avoid accidental entry of a railcar into a basin, administrative procedures and rail control hardware have been provided. Based upon a combination of historical documentation and existing adminstrative controls, a maximum credible impact accident was established. Using this design basis accident, the existing rail control hardware was evaluated for structural adequacy. The K Basin rail spurs are embedded in concrete, which permits truck/trailer entry into the same area. Safety issues for truck applications are also addressed

  18. Lack of HIV infection among truck drivers in Iran using rapid HIV test

    Hossain Jabbari

    2010-01-01

    Full Text Available Background: The aim of this study was to evaluate the prevalence of HIV infection in Iranian long distance truck drivers using rapid HIV test. Methods: The study included 400 consecutive participants in Bazargan city, north-west of Iran in the late 2008 and the early 2009. Results: No HIV infection was observed among these long distance truck drivers. Conclusions: Although results of this study is plausible compared to other similar studies, repeated surveys are necessary to know the trend of HIV infection in truckers in Iran.

  19. Forklift safety a practical guide to preventing powered industrial truck incidents and injuries

    Swartz, George

    1999-01-01

    Written for the more than 1.5 million powered industrial truck operators and supervisors in general industry, as well as those in the construction and marine industries, this Second Edition provides an updated guide to training operators in safety and complying with OSHA's 1999 forklift standard. This edition of Forklift Safety includes a new chapter devoted to the new OSHA 1910.178 standard and new information regarding dock safety, narrow aisle trucks, off-dock incidents, tip-over safety, pallet safety, and carbon monoxide.

  20. The effect of transport time, season and position on the truck on stress response in rabbits

    Liste, M.G; María, G. A.; García-Belenguer, S.; Chacón, G.; Gazzola, P.; Villarroel, M.

    2008-01-01

    The present study analyzed the effect of transport time, season and position on the truck on physiological stress response of commercial rabbits in Aragón (Spain). A total of 156 animals were sampled in a 2x2x3 factorial design testing two transport times: short, 1 hour (1hT) and long, 7 hours (7hT), in two different seasons: hot, during summer (HT) and cold during winter (CT), and three different positions on the truck: upper, middle or lower decks in multi-floor cages on rolling stands (MFR...