Inkjet color-printer control interface

Science.gov (United States)

Kistler, R.; Kriegler, F. J.; Marshall, R. E.

1977-01-01

Special purpose interface permits computer-driven control of inkjet printers. Inkjet printers are answer to problem of high-speed peripheral output devices for computer systems. Control interface was developed to provide high-resolution color-classification maps quickly and economically from multispectral data.

Laserjet Printer Troubleshooting Expert System | Adesola | West ...

African Journals Online (AJOL)

This paper model an expert system called LAPTEX for troubleshooting LaserJet printers' faults. Today, with the innumerable advances in information technologies, computerizing printer's fault troubleshooting and identifying faults is far becoming so vital. Also, printers' fault detection is a complicated process that requires a ...

Maintaining and troubleshooting your 3D printer

CERN Document Server

Bell, Charles

2014-01-01

Maintaining and Troubleshooting Your 3D Printer by Charles Bell is your guide to keeping your 3D printer running through preventive maintenance, repair, and diagnosing and solving problems in 3D printing. If you've bought or built a 3D printer such as a MakerBot only to be confounded by jagged edges, corner lift, top layers that aren't solid, or any of a myriad of other problems that plague 3D printer enthusiasts, then here is the book to help you get past all that and recapture the joy of creative fabrication. The book also includes valuable tips for builders and those who want to modify the

Network migration for printers

CERN Multimedia

2016-01-01

Further to the recent General Purpose (office) Network reorganisation (as announced in the Bulletin - see here), please note that the majority of print devices will be automatically migrated to the new network IP address range on Tuesday 27 September.   This change should be transparent for these devices and therefore end-users, provided you have installed the printers from the Print Service website. A small number of devices will require manual intervention from the Printer Support team in order to migrate correctly. These devices will not change their IP address until the manual intervention, which will be carried out before Monday 3rd October. However, if you have mistakenly connected directly to the printer’s IP address, then your printing will be affected – please uninstall the printer (for help, see: KB3785), and re-install it from the Print Service website (or follow instructions for visitor machines). Please do this as soon as possible in order to avoid printing issues, t...

Low cost nuclear data printer

International Nuclear Information System (INIS)

Punnachiya, S.; Aungkultewaraksa, S.; Pengphol, S.

1988-01-01

The data printer is essential for nuclear radiation measuring system. A low cost nuclear data printer is developed from an electronic printing calculator. It can transfer the counting data from scaler and printout. The basic concept is that the BCD data is transferred and converted to decimal data sequentially by the interfacing circuit. After the counting time is ended, each digit is transferred to the printing calculator by data bus, digit by digit, until all the data are transferred and printed out. The low cost nuclear data printer consists of a CASIO model HR-8 electronic printing calculator and a printer interface model either NT 2602 or NT 2603 which are designed for printing out 6 digit data from the counter/timer CANBERRA model 1772. In this research the NT 2602 interface is designed only to transfer and printing out data. While the NT 2603 interface is designed to transfer, print out and average data. The NT 2603 can average from 2 to 9 sets of counting data. This data interfacing technique can be applied to work with all scientific instruments having readout as digital display and all kinds of electronic printing calculator

Concept for high speed computer printer

Science.gov (United States)

Stephens, J. W.

1970-01-01

Printer uses Kerr cell as light shutter for controlling the print on photosensitive paper. Applied to output data transfer, the information transfer rate of graphic computer printers could be increased to speeds approaching the data transfer rate of computer central processors /5000 to 10,000 lines per minute/.

Wireless 3D Chocolate Printer

Directory of Open Access Journals (Sweden)

FROILAN G. DESTREZA

2014-02-01

Full Text Available This study is for the BSHRM Students of Batangas State University (BatStateU ARASOF for the researchers believe that the Wireless 3D Chocolate Printer would be helpful in their degree program especially on making creative, artistic, personalized and decorative chocolate designs. The researchers used the Prototyping model as procedural method for the successful development and implementation of the hardware and software. This method has five phases which are the following: quick plan, quick design, prototype construction, delivery and feedback and communication. This study was evaluated by the BSHRM Students and the assessment of the respondents regarding the software and hardware application are all excellent in terms of Accuracy, Effecitveness, Efficiency, Maintainability, Reliability and User-friendliness. Also, the overall level of acceptability of the design project as evaluated by the respondents is excellent. With regard to the observation about the best raw material to use in 3D printing, the chocolate is good to use as the printed material is slightly distorted,durable and very easy to prepare; the icing is also good to use as the printed material is not distorted and is very durable but consumes time to prepare; the flour is not good as the printed material is distorted, not durable but it is easy to prepare. The computation of the economic viability level of 3d printer with reference to ROI is 37.14%. The recommendation of the researchers in the design project are as follows: adding a cooling system so that the raw material will be more durable, development of a more simplified version and improving the extrusion process wherein the user do not need to stop the printing process just to replace the empty syringe with a new one.

Hands-On Skills for Caregivers

Science.gov (United States)

... A + A You are here Home Hands-On Skills for Caregivers Printer-friendly version When you’re ... therapist who can help you develop your transferring skills. Allow for their reality Remember to accept your ...

Depression and Caregiving

Science.gov (United States)

... FCA - A A + A You are here Home Depression and Caregiving Order this publication Printer-friendly version ... a more serious depression over time. Symptoms of Depression People experience depression in different ways. Some may ...

Caregiver Statistics: Demographics

Science.gov (United States)

... You are here Home Selected Long-Term Care Statistics Order this publication Printer-friendly version What is ... needs and services are wide-ranging and complex, statistics may vary from study to study. Sources for ...

Taking Care of You: Self-Care for Family Caregivers

Science.gov (United States)

... Taking Care of YOU: Self-Care for Family Caregivers Order this publication Printer-friendly version First, Care ... 25 26 27 28 29 30 Smart Patients Caregivers Community In partnership with Family Caregiver Alliance Learn ...

High-Efficiency Solar-Powered 3-D Printers for Sustainable Development

Directory of Open Access Journals (Sweden)

Jephias Gwamuri

2016-01-01

Full Text Available The release of the open source 3-D printer known as the RepRap (a self-Replicating Rapid prototyper resulted in the potential for distributed manufacturing of products for significantly lower costs than conventional manufacturing. This development, coupled with open source-appropriate technology (OSAT, has enabled the opportunity for 3-D printers to be used for sustainable development. In this context, OSAT provides the opportunity to modify and improve the physical designs of their printers and desired digitally-shared objects. However, these 3-D printers require electricity while more than a billion people still lack electricity. To enable the utilization of RepRaps in off-grid communities, solar photovoltaic (PV-powered mobile systems have been developed, but recent improvements in novel delta-style 3-D printer designs allows for reduced costs and improved performance. This study builds on these innovations to develop and experimentally validate a mobile solar-PV-powered delta 3-D printer system. It is designed to run the RepRap 3-D printer regardless of solar flux. The electrical system design is tested outdoors for operating conditions: (1 PV charging battery and running 3-D printer; (2 printing under low insolation; (3 battery powering the 3-D printer alone; (4 PV charging the battery only; and (5 battery fully charged with PV-powered 3-D printing. The results show the system performed as required under all conditions providing feasibility for adoption in off-grid rural communities. 3-D printers powered by affordable mobile PV solar systems have a great potential to reduce poverty through employment creation, as well as ensuring a constant supply of scarce products for isolated communities.

Interface Circuit For Printer Port

Science.gov (United States)

Tucker, Jerry H.; Yadlowsky, Ann B.

1991-01-01

Electronic circuit, called printer-port interface circuit (PPI) developed to overcome certain disadvantages of previous methods for connecting IBM PC or PC-compatible computer to other equipment. Has both reading and writing modes of operation. Very simple, requiring only six integrated circuits. Provides for moderately fast rates of transfer of data and uses existing unmodified circuit card in IBM PC. When used with appropriate software, circuit converts printer port on IBM PC, XT, AT, or compatible personal computer to general purpose, 8-bit-data, 16-bit address bus that connects to multitude of devices.

Acceptance procedures: Microfilm printer

Science.gov (United States)

Lockwood, H. E.

1973-01-01

Acceptance tests were made for a special order automatic additive color microfilm printer. Tests include film capacity, film transport, resolution, illumination uniformity, exposure range checks, and color cuing considerations.

DELTA 3D PRINTER

Directory of Open Access Journals (Sweden)

ȘOVĂILĂ Florin

2016-07-01

Full Text Available 3D printing is a very used process in industry, the generic name being “rapid prototyping”. The essential advantage of a 3D printer is that it allows the designers to produce a prototype in a very short time, which is tested and quickly remodeled, considerably reducing the required time to get from the prototype phase to the final product. At the same time, through this technique we can achieve components with very precise forms, complex pieces that, through classical methods, could have been accomplished only in a large amount of time. In this paper, there are presented the stages of a 3D model execution, also the physical achievement after of a Delta 3D printer after the model.

3-D printers for libraries

CERN Document Server

Griffey, Jason

2014-01-01

As the maker movement continues to grow and 3-D printers become more affordable, an expanding group of hobbyists is keen to explore this new technology. In the time-honored tradition of introducing new technologies, many libraries are considering purchasing a 3-D printer. Jason Griffey, an early enthusiast of 3-D printing, has researched the marketplace and seen several systems first hand at the Consumer Electronics Show. In this report he introduces readers to the 3-D printing marketplace, covering such topics asHow fused deposition modeling (FDM) printing workBasic terminology such as build

Implementation of a 3D printer into a small business

OpenAIRE

Kodejšová, Jana

2017-01-01

This thesis deals with the implementation of a 3D printer into a small business. The theoret-ical part deals with technology of 3D printing, types of 3D printers, as well as basic materi-als suitable for 3D printing. The practical part is devoted to the purchasing of a 3D printer for this company that deals with the service and the supply of bicycles and other cycling needs. There is chosen the most suitable 3D printer for this business, and there are also ex-amples of specific parts that thi...

Piezo inkjet printer

NARCIS (Netherlands)

2006-01-01

An inkjet printer containing a substantially closed ink duct and a transducer used to generate a pressure wave in the duct, wherein the transducer comprises a first part and, separate from the first part, a second part whereby, by actuation of the transducer, the first part manifests a first

A comparison of the Space Station version of ASTROMAG with two free-flyer versions

International Nuclear Information System (INIS)

Green, M.A.

1992-06-01

This Report compares the Space Station version of ASTROMAG with free-flyer versions of ASTROMAG which could fly on an Atlas lla rocket and a Delta rocket. Launch with either free-flyer imposes severe weight limits on the magnet and its cryogenic system. Both versions of ASTROMAG magnet which fly on free-flying satellites do not have to be charged more than once during the mission. This permits one to simplify the charging system and the cryogenic system. The helium ll pump loop which supplies helium to the gas cooled electrical leads can be eliminated in both of the free-flyer versions of the ASTROMAG magnet. This report describes the superconducting dipole moment correction coils which are necessary for the magnet to operate on a free-flying satellite

3D PRINTERS – NEW POSSIBILITIES IN EDUCATION

Directory of Open Access Journals (Sweden)

Joanna Szulżyk-Cieplak

2014-11-01

Full Text Available In the last few years a significant growth of three-dimensional printing has been noticed. Although 3D printers have been around for about 30 years, they were very expensive, that is why they were available in the industry only in the majority . In recent years, prices of 3D printers have fallen more than tenfold, owing to the fact they are used not only in large enterprises but also in all kinds of educational institutions, small businesses or in do-it-yourself men’s houses. They are, inter alia, used to construct physical models, so much needed in education. Nowadays, one of the most popular 3D printing technologies is FDM (Fused Deposition Modeling. Relatively low prices of printers in this technology make them available for almost everyone. The paper discusses the technology of rapid prototyping, with particular emphasis on the use of 3D printing and appropriately matched printer to designed laboratory stand.

Aplikasi Expert System Troubleshoot Printer Canon Berbasis Web (Studi Kasus: CV SUNTEC Komputer

Directory of Open Access Journals (Sweden)

Beriman Panjaitan

2017-05-01

Full Text Available AbstrakPengguna printer pada umumnya tidak luput dari kerusakan atau masalah meskipun kerusakan itu mungkin bisa terjadi secara tiba-tiba tanpa sepengetahuan kita, peranan teknisi pun dibutuhkan. Pengguna atau pemilik printer yang tidak mengetahui penyebab-penyebab kerusakan dan cara mengecek di saat printer mengalami kerusakan. Sangat di sayangkan jika yang terjadi hanya kerusakan kecil yang semestinya dapat di perbaiki sendiri, sementara waktu menunggu perbaikan sudah cukup lama dan dan biaya yang dikeluarkan besar bila dibawa ke tempat service. Tugas akhir ini akan di rancang suatu perangkat lunak yang dapat melakukan pengecekan gejala pada printer dan akhirnya menemukan kemungkinan kerusakan pada printer solusinya. Aplikasi expert ini menggunakan bahasa pemograman PHP dan MySQL. Kata kunci: Sistem Pakar, Printer Canon,Website, PHP, MySQL Abstract Users printers are generally not spared from damage or problems despite the damage it might happen suddenly without our knowledge, the role of technicians was needed. User or printer owners who do not know the causes of damage and how to check in while the printer is damaged. Very regrettable if that happens only minor damage should be repaired itself, while the waiting time is long enough and the improvement and substantial costs incurred when brought into service. This final project will be designed a software that can check the symptoms on the printer and finally found the possibility of damage to the printer solution. This expert applications using the programming language PHP and MySQL.  Keywords: Expert System, Printer Canon,Website, PHP, MySQL

78 FR 56706 - Depository Library Council to the Public Printer; Meeting

Science.gov (United States)

2013-09-13

... GOVERNMENT PRINTING OFFICE Depository Library Council to the Public Printer; Meeting The Depository Library Council to the Public Printer (DLC) will meet on Monday, October 21, 2013 through.... Davita Vance-Cooks, Public Printer of the United States. [FR Doc. 2013-22247 Filed 9-12-13; 8:45 am...

75 FR 61760 - Depository Library Council to the Public Printer; Meeting

Science.gov (United States)

2010-10-06

... GOVERNMENT PRINTING OFFICE Depository Library Council to the Public Printer; Meeting The Depository Library Council to the Public Printer (DLC) will meet on Monday, October 18, 2010, through... regulations. Robert C. Tapella, Public Printer of the United States. [FR Doc. 2010-25047 Filed 10-5-10; 8:45...

77 FR 58381 - Depository Library Council to the Public Printer; Meeting

Science.gov (United States)

2012-09-20

... GOVERNMENT PRINTING OFFICE Depository Library Council to the Public Printer; Meeting The Depository Library Council to the Public Printer will meet on Monday, October 15, 2012 through Thursday... Printer of the United States. [FR Doc. 2012-23015 Filed 9-19-12; 8:45 am] BILLING CODE 1520-01-P ...

76 FR 13617 - Depository Library Council to the Public Printer Meeting

Science.gov (United States)

2011-03-14

... GOVERNMENT PRINTING OFFICE Depository Library Council to the Public Printer Meeting The Depository Library Council to the Public Printer (DLC) will meet on Monday, April 4, 2011 through Wednesday, April 6... Disabilities Act and meets all Fire Safety Act regulations. William J. Boarman, Public Printer of the United...

75 FR 18209 - Depository Library Council to the Public Printer; Meeting

Science.gov (United States)

2010-04-09

... GOVERNMENT PRINTING OFFICE Depository Library Council to the Public Printer; Meeting The Depository Library Council to the Public Printer (DLC) will meet on Monday, April 26, 2010, through Wednesday.... Robert C. Tapella, Public Printer of the United States. [FR Doc. 2010-8123 Filed 4-8-10; 8:45 am] BILLING...

Space Images for NASA JPL Android Version

Science.gov (United States)

Nelson, Jon D.; Gutheinz, Sandy C.; Strom, Joshua R.; Arca, Jeremy M.; Perez, Martin; Boggs, Karen; Stanboli, Alice

2013-01-01

This software addresses the demand for easily accessible NASA JPL images and videos by providing a user friendly and simple graphical user interface that can be run via the Android platform from any location where Internet connection is available. This app is complementary to the iPhone version of the application. A backend infrastructure stores, tracks, and retrieves space images from the JPL Photojournal and Institutional Communications Web server, and catalogs the information into a streamlined rating infrastructure. This system consists of four distinguishing components: image repository, database, server-side logic, and Android mobile application. The image repository contains images from various JPL flight projects. The database stores the image information as well as the user rating. The server-side logic retrieves the image information from the database and categorizes each image for display. The Android mobile application is an interfacing delivery system that retrieves the image information from the server for each Android mobile device user. Also created is a reporting and tracking system for charting and monitoring usage. Unlike other Android mobile image applications, this system uses the latest emerging technologies to produce image listings based directly on user input. This allows for countless combinations of images returned. The backend infrastructure uses industry-standard coding and database methods, enabling future software improvement and technology updates. The flexibility of the system design framework permits multiple levels of display possibilities and provides integration capabilities. Unique features of the software include image/video retrieval from a selected set of categories, image Web links that can be shared among e-mail users, sharing to Facebook/Twitter, marking as user's favorites, and image metadata searchable for instant results.

Measurements of Wiener spectra of laser printer in a computed radiography

International Nuclear Information System (INIS)

Yamauchi, Syuichi; Ueda, Katsuhiko; Nishihara, Sadamitsu; Ohtsuka, Akiyoshi; Fujita, Hiroshi; Morishita, Junji; Fujikawa, Tsuyoshi.

1992-01-01

Sources of noise in a computed radiography (CR) were investigated by measuring three different Wiener spectra: 1) laser printer Wiener spectra including CR film, 2) Wiener spectrum of CR film (single emulsion), and 3) overall Wiener spectra. To measure the noise contributed by the laser printer, 'image data' (i.e., image having a constant pixel value) were produced on a personal computer and were sent to the laser printer in the CR system. The noise level of laser printer was comparable to that of the CR film at low spatial frequencies ( 4 cycle/mm) was higher than that of the film. Laser printer Wiener spectra obtained in the perpendicular direction relative to the laser beam scanning direction were comparable at low spatial frequencies, but greater at high spatial frequencies, to those obtained in the parallel direction. And a spectral peak around 10 cycle/mm was obtained in the Wiener spectrum in the perpendicular direction. The peak is caused mainly by a banding artifact. Overall Wiener spectra in the parallel and perpendicular directions show the same tendency as those of the laser printer, but the noise level of the overall Wiener spectrum was increased mainly by X-ray quantum mottle at low spatial frequencies. In conclusion, the noise of laser printer greatly increases the overall Wiener spectrum at high spatial frequencies. (author)

Advanced 3D Printers for Cellular Solids

Science.gov (United States)

2016-06-30

06-2016 1-Aug-2014 31-Dec-2015 Final Report: Advanced 3D printers for Cellular Solids The views, opinions and/or findings contained in this report are...2211 3d printing, cellular solids REPORT DOCUMENTATION PAGE 11. SPONSOR/MONITOR’S REPORT NUMBER(S) 10. SPONSOR/MONITOR’S ACRONYM(S) ARO 8...Papers published in non peer-reviewed journals: Final Report: Advanced 3D printers for Cellular Solids Report Title Final Report for DURIP grant W911NF

76 FR 58005 - Meeting Notice; Depository Library Council to the Public Printer

Science.gov (United States)

2011-09-19

... GOVERNMENT PRINTING OFFICE Meeting Notice; Depository Library Council to the Public Printer The Depository Library Council to the Public Printer (DLC) will meet on Monday, October 17, through Thursday..., Public Printer of the United States. [FR Doc. 2011-23948 Filed 9-16-11; 8:45 am] BILLING CODE 1520-01-P ...

Operative and economic evaluation of a 'Laser Printer Multimodality' System

International Nuclear Information System (INIS)

Battaglia, G.; Moscatelli, G.; Maroldi, R.; Chiesa, A.

1991-01-01

The increasing application of digital techniques to diagnostic imaging is causing significant changes in several related activities, such as a reproduction of digital images on film. In the Department of Diagnostic Imaging of the University of Brescia, about 70% of the whole of images are produced by digital techniques; at present, most of these images are reproduced on film with a Multimodality System interfacing CT, MR, DSA, and DR units with a single laser printer. Our analysis evaluates the operative and economics aspects of image reproduction, by comparing the 'single cassette' multiformat Camera and the Laser Printer Multimodality SAystem. Our results point out the advantages obtained by reproducing images with a Laser Printer Multimodality System: outstanding quality, reproduction of multiple originals, and marked reduction in the time needed for both image archiving and film handling. The Laser Printer Multimodality System allows over 5 hours/day to be saved -that is to say the working day of an operator, who can be thus shifted to other functions. The important economic aspect of the reproduction of digital images on film proves the Laser Printer Multimodality System to have some advantage over Cameras

The "Digital Friend": A knowledge-based decision support system for space crews

Science.gov (United States)

Hoermann, Hans-Juergen; Johannes, Bernd; Petrovich Salnitski, Vyacheslav

Space travel of far distances presents exceptional strain on the medical and psychological well-being of the astronauts who undertake such missions. An intelligent knowledge management system has been developed, to assist space crews on long-duration missions as an autonomous decision support system, called the "Digital Friend". This system will become available upon request for the purpose of coaching group processes and individual performance levels as well as aiding in tactical decision processes by taking crew condition parameters into account. In its initial stage, the "Digital Friend" utilizes interconnected layers of knowledge, which encompass relevant models of operational, situational, individual psycho-physiological as well as group processes. An example is the human life science model that contains historic, diagnostic, and prognostic knowledge about the habitual, actual, and anticipated patterns of physiological, cognitive, and group psychology parameters of the crew members. Depending on the available data derived from pre-mission screening, regular check-ups, or non-intrusive onboard monitoring, the "Digital Friend" can generate a situational analysis and diagnose potential problems. When coping with the effects of foreseeable and unforeseen stressors encountered during the mission, the system can provide feedback and support the crew with a recommended course of actions. The first prototype of the "Digital Friend" employs the Neurolab/Healthlab platform developed in a cooperation of DLR and IBMP. The prototype contains psycho-physiological sensors with multiple Heally Satellites that relay data to the intelligent Heally Masters and a telemetric Host station. The analysis of data from a long-term simulation study illustrates how the system can be used to estimate the operators' current level of skill reliability based on Salnitski's model [V. Salnitski, A. Bobrov, A. Dudukin, B. Johannes, Reanalysis of operators reliability in professional skills

Development of a Resilient 3-D Printer for Humanitarian Crisis Response

Directory of Open Access Journals (Sweden)

Benjamin L. Savonen

2018-03-01

Full Text Available Rapid manufacturing using 3-D printing is a potential solution to some of the most pressing issues for humanitarian logistics. In this paper, findings are reported from a study that involved development of a new type of 3-D printer. In particular, a novel 3-D printer that is designed specifically for reliable rapid manufacturing at the sites of humanitarian crises. First, required capabilities are developed with design elements of a humanitarian 3-D printer, which include, (1 fused filament fabrication, (2 open source self-replicating rapid prototyper design, (3 modular, (4 separate frame, (5 protected electronics, (6 on-board computing, (7 flexible power supply, and (8 climate control mechanisms. The technology is then disclosed with an open source license for the Kijenzi 3-D Printer. A swarm of five Kijenzi 3-D printers are evaluated for rapid part manufacturing for two months at health facilities and other community locations in both rural and urban areas throughout Kisumu County, Kenya. They were successful for their ability to function independently of infrastructure, transportability, ease of use, ability to withstand harsh environments and costs. The results are presented and conclusions are drawn about future work necessary for the Kijenzi 3-D Printer to meet the needs of rapid manufacturing in a humanitarian context.

Space shuttle general purpose computers (GPCs) (current and future versions)

Science.gov (United States)

1988-01-01

Current and future versions of general purpose computers (GPCs) for space shuttle orbiters are represented in this frame. The two boxes on the left (AP101B) represent the current GPC configuration, with the input-output processor at far left and the central processing unit (CPU) at its side. The upgraded version combines both elements in a single unit (far right, AP101S).

Virtual printer : an environment for digital print modeling and inspection

NARCIS (Netherlands)

Marchenko, V.

2014-01-01

Océ-Technologies B.V., a member of the Canon Group, specializes in providing solutions for enterprise printing, large format printing, and production printing. Software is an important part of a modern printer. One of the tasks for inkjet-printer software is to transform input print data into timed

Characterization of chemical contaminants generated by a desktop fused deposition modeling 3-dimensional Printer.

Science.gov (United States)

Stefaniak, Aleksandr B; LeBouf, Ryan F; Yi, Jinghai; Ham, Jason; Nurkewicz, Timothy; Schwegler-Berry, Diane E; Chen, Bean T; Wells, J Raymond; Duling, Matthew G; Lawrence, Robert B; Martin, Stephen B; Johnson, Alyson R; Virji, M Abbas

2017-07-01

Printing devices are known to emit chemicals into the indoor atmosphere. Understanding factors that influence release of chemical contaminants from printers is necessary to develop effective exposure assessment and control strategies. In this study, a desktop fused deposition modeling (FDM) 3-dimensional (3-D) printer using acrylonitrile butadiene styrene (ABS) or polylactic acid (PLA) filaments and two monochrome laser printers were evaluated in a 0.5 m 3 chamber. During printing, chamber air was monitored for vapors using a real-time photoionization detector (results expressed as isobutylene equivalents) to measure total volatile organic compound (TVOC) concentrations, evacuated canisters to identify specific VOCs by off-line gas chromatography-mass spectrometry (GC-MS) analysis, and liquid bubblers to identify carbonyl compounds by GC-MS. Airborne particles were collected on filters for off-line analysis using scanning electron microscopy with an energy dispersive x-ray detector to identify elemental constituents. For 3-D printing, TVOC emission rates were influenced by a printer malfunction, filament type, and to a lesser extent, by filament color; however, rates were not influenced by the number of printer nozzles used or the manufacturer's provided cover. TVOC emission rates were significantly lower for the 3-D printer (49-3552 µg h -1 ) compared to the laser printers (5782-7735 µg h -1 ). A total of 14 VOCs were identified during 3-D printing that were not present during laser printing. 3-D printed objects continued to off-gas styrene, indicating potential for continued exposure after the print job is completed. Carbonyl reaction products were likely formed from emissions of the 3-D printer, including 4-oxopentanal. Ultrafine particles generated by the 3-D printer using ABS and a laser printer contained chromium. Consideration of the factors that influenced the release of chemical contaminants (including known and suspected asthmagens such as styrene and

The Fine Print: How Schools Can Get the Best Value for Their Printer Dollar

Science.gov (United States)

Careless, James

2007-01-01

Printers represent a big chunk of school districts' IT budgets. Unlike computers, however, most of the money schools spend on printers is not on the machines themselves but on keeping them serviced and filled with toner, drums, and paper. In this article, the author discusses five critical questions to ask before buying a printer.

Emission of particulate matter from a desktop three-dimensional (3D) printer

Science.gov (United States)

Yi, Jinghai; LeBouf, Ryan F.; Duling, Matthew G.; Nurkiewicz, Timothy; Chen, Bean T.; Schwegler-Berry, Diane; Virji, M. Abbas; Stefaniak, Aleksandr B.

2016-01-01

ABSTRACT Desktop three-dimensional (3D) printers are becoming commonplace in business offices, public libraries, university labs and classrooms, and even private homes; however, these settings are generally not designed for exposure control. Prior experience with a variety of office equipment devices such as laser printers that emit ultrafine particles (UFP) suggests the need to characterize 3D printer emissions to enable reliable risk assessment. The aim of this study was to examine factors that influence particulate emissions from 3D printers and characterize their physical properties to inform risk assessment. Emissions were evaluated in a 0.5-m3 chamber and in a small room (32.7 m3) using real-time instrumentation to measure particle number, size distribution, mass, and surface area. Factors evaluated included filament composition and color, as well as the manufacturer-provided printer emissions control technologies while printing an object. Filament type significantly influenced emissions, with acrylonitrile butadiene styrene (ABS) emitting larger particles than polylactic acid (PLA), which may have been the result of agglomeration. Geometric mean particle sizes and total particle (TP) number and mass emissions differed significantly among colors of a given filament type. Use of a cover on the printer reduced TP emissions by a factor of 2. Lung deposition calculations indicated a threefold higher PLA particle deposition in alveoli compared to ABS. Desktop 3D printers emit high levels of UFP, which are released into indoor environments where adequate ventilation may not be present to control emissions. Emissions in nonindustrial settings need to be reduced through the use of a hierarchy of controls, beginning with device design, followed by engineering controls (ventilation) and administrative controls such as choice of filament composition and color. PMID:27196745

Emission of particulate matter from a desktop three-dimensional (3D) printer.

Science.gov (United States)

Yi, Jinghai; LeBouf, Ryan F; Duling, Matthew G; Nurkiewicz, Timothy; Chen, Bean T; Schwegler-Berry, Diane; Virji, M Abbas; Stefaniak, Aleksandr B

2016-01-01

Desktop three-dimensional (3D) printers are becoming commonplace in business offices, public libraries, university labs and classrooms, and even private homes; however, these settings are generally not designed for exposure control. Prior experience with a variety of office equipment devices such as laser printers that emit ultrafine particles (UFP) suggests the need to characterize 3D printer emissions to enable reliable risk assessment. The aim of this study was to examine factors that influence particulate emissions from 3D printers and characterize their physical properties to inform risk assessment. Emissions were evaluated in a 0.5-m(3) chamber and in a small room (32.7 m(3)) using real-time instrumentation to measure particle number, size distribution, mass, and surface area. Factors evaluated included filament composition and color, as well as the manufacturer-provided printer emissions control technologies while printing an object. Filament type significantly influenced emissions, with acrylonitrile butadiene styrene (ABS) emitting larger particles than polylactic acid (PLA), which may have been the result of agglomeration. Geometric mean particle sizes and total particle (TP) number and mass emissions differed significantly among colors of a given filament type. Use of a cover on the printer reduced TP emissions by a factor of 2. Lung deposition calculations indicated a threefold higher PLA particle deposition in alveoli compared to ABS. Desktop 3D printers emit high levels of UFP, which are released into indoor environments where adequate ventilation may not be present to control emissions. Emissions in nonindustrial settings need to be reduced through the use of a hierarchy of controls, beginning with device design, followed by engineering controls (ventilation) and administrative controls such as choice of filament composition and color.

Optimization of spectral printer modeling based on a modified cellular Yule-Nielsen spectral Neugebauer model.

Science.gov (United States)

Liu, Qiang; Wan, Xiaoxia; Xie, Dehong

2014-06-01

The study presented here optimizes several steps in the spectral printer modeling workflow based on a cellular Yule-Nielsen spectral Neugebauer (CYNSN) model. First, a printer subdividing method was developed that reduces the number of sub-models while maintaining the maximum device gamut. Second, the forward spectral prediction accuracy of the CYNSN model for each subspace of the printer was improved using back propagation artificial neural network (BPANN) estimated n values. Third, a sequential gamut judging method, which clearly reduced the complexity of the optimal sub-model and cell searching process during printer backward modeling, was proposed. After that, we further modified the use of the modeling color metric and comprehensively improved the spectral and perceptual accuracy of the spectral printer model. The experimental results show that the proposed optimization approaches provide obvious improvements in aspects of the modeling accuracy or efficiency for each of the corresponding steps, and an overall improvement of the optimized spectral printer modeling workflow was also demonstrated.

Super Global Projects and Environmentally Friendly Technologies Used in Space Exploration: Realities and Prospects of the Space Age

Directory of Open Access Journals (Sweden)

Sergey Krichevsky

2018-02-01

Full Text Available The 60th anniversary of the Space Age is an important intermediate finishing point on the way of a man and the whole humanity to space. Along with the outstanding achievements, there are a number of challenges and contradictions in space exploration due to the aggravation of the global crisis on Earth, low efficiency and the backlog of space research in the transition to a new technology based reality and clean technologies. Both the international astronautics and the space exploration area nowadays face difficulties in choosing a new paradigm and a development strategy that is becoming even more complicated due to the current unstable and turbulent situation on Earth. The article reveals the optimistic scenario of further space exploration, as well as the methodological and practical aspects of new projects and technologies. The periodization of the Space Age history has been conducted. It has been also proposed a new classification of the “space” phenomenon due to concretizing the concept of “global” in the form of a three-scale structure encompassing the following levels: 1 planetary global; 2 super global; 3 universally global. The notion of “super global space exploration project” has been introduced. The concept of further space exploration is proposed, which includes four interrelated super global projects:1 Earth Protection System from Asteroid and Comet Threat; 2 Moon Exploration; 3 Mars Exploration; 4 Cosmic Humanity. Since the humanity is embarking on the practical implementation of these super global projects, it is urgent to make a transition towards a new technology based order, as well as up-to-date technologies. A couple of ecological projects and space exploration technologies of the 20th and 21st centuries have been exemplified and analyzed. It has been also worked out the list of new environmentally friendly space technologies and projects. The research makes an emphasis upon a great potential of clean and green

Validation of image quality in full-field digital mammography: Is the replacement of wet by dry laser printers justified?

International Nuclear Information System (INIS)

Schueller, Gerd; Kaindl, Elisabeth; Langenberger, Herbert; Stadler, Alfred; Schueller-Weidekamm, Claudia; Semturs, Friedrich; Helbich, Thomas H.

2007-01-01

Objective: Dry laser printers have replaced wet laser printers to produce hard copies of high-resolution digital images, primarily because of environmental concerns. However, no scientific research data have been published that compare the image quality of dry and wet laser printers in full-field digital mammography (FFDM). This study questions the image quality of these printers. Materials and methods: Objective image quality parameters of both printers were evaluated using a standardized printer test image, i.e., optical density and detectability of specific image elements (lines, curves, and shapes). Furthermore, mammograms of 129 patients with different breast tissue composition patterns were imaged with both printers. A total of 1806 subjective image quality parameters (brightness, contrast, and detail detection of anatomic structures), the detectability of breast lesions, as well as diagnostic performance according to the BI-RADS classification were evaluated. In addition, the presence of film artifacts was investigated. Results: Optical density values were equal for the dry and the wet laser printer. Detection of specific image elements on the printer test image was not different. Ratings of subjective image quality parameters were equal, as were the detectability of breast lesions and the diagnostic performance. Dry laser printer images showed more artifacts (164 versus 27). However, these artifacts did not influence image quality. Conclusion: Based on the evidence of objective and subjective parameters, a dry laser printer equals the image quality of a wet laser printer in FFDM. Therefore, not only for reasons of environmental preference, the replacement of wet laser printers by dry laser printers in FFDM is justified

"Friends" and "Foes" in the Social Space of the Tatar Ethnic Group

Directory of Open Access Journals (Sweden)

Nataliia O. Khazieva

2017-10-01

Full Text Available The history of the World Culture is a demonstration of the "war" between the two opposites: on the one hand, we see a trend towards unification of all aspects of life on a global scale, and on the other, there is a clear confrontation between different groups of mankind. Of the many causes of the disunity of the people, the authors' focus at the opposition "friend – foe" as a metaphysical principle of formation of social space wasn't chosen by accident. The fact is that any culture, in principle, is dichotomous, and the opposition "friend – foe" is the fullest incarnation of this dichotomy. As a universal principle of the formation and functioning of the cultures, it originally manifests itself in every one of them. And, as the authors of the study suggest: this opposition could either "work" in general on the cross-cultural cooperation and unity or be one of the confrontation sources. The main result of the study is that history has prepared and put forward the Tartars for carrying out a special mission, to unite peoples and cultures. But the revolutionary social upheavals that take place in the modern world pose a threat (in the circumstances of forced migration of peoples, the growth of national consciousness of the former Soviet Union space, and especially in the face of Islamic fundamentalism on fulfilling this function.

A Printer Indexing System for Color Calibration with Applications in Dietary Assessment.

Science.gov (United States)

Fang, Shaobo; Liu, Chang; Zhu, Fengqing; Boushey, Carol; Delp, Edward

2015-09-01

In image based dietary assessment, color is a very important feature in food identification. One issue with using color in image analysis in the calibration of the color imaging capture system. In this paper we propose an indexing system for color camera calibration using printed color checkerboards also known as fiducial markers (FMs). To use the FM for color calibration one must know which printer was used to print the FM so that the correct color calibration matrix can be used for calibration. We have designed a printer indexing scheme that allows one to determine which printer was used to print the FM based on a unique arrangement of color squares and binarized marks (used for error control) printed on the FM. Using normalized cross correlation and pattern detection, the index corresponding to the printer for a particular FM can be determined. Our experimental results show this scheme is robust against most types of lighting conditions.

Fume emissions from a low-cost 3-D printer with various filaments.

Science.gov (United States)

Floyd, Evan L; Wang, Jun; Regens, James L

2017-07-01

3-D printing is an additive manufacturing process involving the injection of melted thermoplastic polymers, which are then laid down in layers to achieve a pre-designed shape. The heated deposition process raises concerns of potential aerosol and volatile organic compounds (VOC) emission and exposure. The decreasing cost of desktop 3-D printers has made the use of 3-D printers more acceptable in non-industrial workplaces lacking sufficient ventilation. Meanwhile, little is known about the characteristics of 3-D printing fume emission. The objective of this study was to characterize aerosols and VOC emissions generated from various filaments used with a low-cost 3-D printer in an environmental testing chamber. A pre-designed object was printed in 1.25 hours using eight types of filaments. A scanning mobility particle sizer and an aerodynamic particle sizer were employed to measure the particle size distribution in sub-half-micron fraction (printers due to high respirablity, especially if used in settings without proper guidance and engineering control.

Verification of photon attenuation characteristics for 3D printer based small animal lung model

International Nuclear Information System (INIS)

Lee, Se Ho; Lee, Seung Wook; Han, Su Chul; Park, Seung Woo

2016-01-01

Since it is difficult to measure absorbed dose to mice in vivo, replica mice are mostly used as alternative. In this study, realistic mouse phantom was fabricated by using 3D printer (object500 connex3, Stratasys, USA). Elemental inks as material of 3D printer were selected corresponding to mouse tissue. To represent lung, selected material was partially used with air layer. In order to verify material equivalent, super-flex bolus was simply compared to verify photon attenuation characteristics. In the case of lung, Hounsfield unit (HU) of the phantom were compared with a live mouse. In this study, we fabricated mouse phantom by using 3D printer, and practically verified photon attenuation characteristics. The fabricated phantom shows tissue equivalence as well as similar geometry with live mouse. As more and more growing of 3D printer technique, 3D printer based small preclinical animal phantom would increase reliability of verification of absorbed dose in small animal for preclinical study

Verification of photon attenuation characteristics for 3D printer based small animal lung model

Energy Technology Data Exchange (ETDEWEB)

Lee, Se Ho; Lee, Seung Wook [Pusan National University, Busan (Korea, Republic of); Han, Su Chul; Park, Seung Woo [Korea Institute of Radiological and Medical Sciences, Seoul (Korea, Republic of)

2016-05-15

Since it is difficult to measure absorbed dose to mice in vivo, replica mice are mostly used as alternative. In this study, realistic mouse phantom was fabricated by using 3D printer (object500 connex3, Stratasys, USA). Elemental inks as material of 3D printer were selected corresponding to mouse tissue. To represent lung, selected material was partially used with air layer. In order to verify material equivalent, super-flex bolus was simply compared to verify photon attenuation characteristics. In the case of lung, Hounsfield unit (HU) of the phantom were compared with a live mouse. In this study, we fabricated mouse phantom by using 3D printer, and practically verified photon attenuation characteristics. The fabricated phantom shows tissue equivalence as well as similar geometry with live mouse. As more and more growing of 3D printer technique, 3D printer based small preclinical animal phantom would increase reliability of verification of absorbed dose in small animal for preclinical study.

Monthly version of HadISST sea surface temperature state-space components

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — State-Space Decomposition of Monthly version of HadISST sea surface temperature component (1-degree). See Rayner, N. A., Parker, D. E., Horton, E. B., Folland, C....

APPLICATIONS OF REPRAP THREE-DIMENSIONAL PRINTERS IN DENTISTRY- A LITERATURE REVIEW

Directory of Open Access Journals (Sweden)

Alexandru-Victor BURDE

2015-03-01

Full Text Available Purpose – This paper is intended to summarize the current available literature in which low-cost, open-source RepRap 3D printers are incorporated in the field of dentistry in an attempt to improve or replace conventional clinical and/or laboratory procedures. Methodology– An electronic search of publications from January 2004 to July 2014 was performed, by two researchers, in two electronic databases: Medline (PubMed and EMBASE Library. All searches were limited to human subjects investigations, published in English. Search terms included general and specific terms from the field of dentistry and additive manufacturing. Findings – The contribution of RepRap 3D printers to the field of dentistry is so far limited to only two applications, respectively reconstruction of study models for orthodontic measurements and reconstruction of skull segments. Originality/value – This review brings focus on the few researches and applications of low-cost RepRap printers in the dental field. In spite of the promising results reported, there still remains a sizable sector in which the capabilities of these low-cost, open source 3d printers are to be tested.

Fabrication of a customized bone scaffold using a homemade medical 3D printer for comminuted fractures

Science.gov (United States)

Yoon, Do-Kun; Jung, Joo-Young; Shin, Han-Back; Kim, Moo-Sub; Choe, Bo-Young; Kim, Sunmi; Suh, Tae Suk; Lee, Keum Sil; Xing, Lei

2016-09-01

The purpose of this study was to show a 3D printed reconstruction model of a bone destroyed by a comminuted fracture. After a thoracic limb of a cow with a comminuted fracture was scanned by using computed tomography, a scaffold was designed by using a 3D modeling tool for its reconstruction and fabricated by using a homemade medical 3D printer. The homemade medical 3D printer was designed for medical use. In order to reconstruct the geometry of the destroyed bone, we use the geometry of a similar section (reference geometry) of normal bone in the 3D modeling process. The missing part between the destroyed ridge and the reference geometry was filled with an effective space by using a manual interpolation. Inexpensive materials and free software were used to construct the medical 3D printer system. The fabrication of the scaffold progressed according to the design of reconstructed bone by using this medical 3D printer. The material of the scaffold was biodegradable material, and could be transplanted into the human body. The fabricated scaffold was correctly inserted into the fractured bone in place of the destroyed portion, with good agreement. According to physical stress test results, the performance of printing resolution was 0.1 mm. The average geometrical error of the scaffold was below 0.3 mm. The reconstructed bone by using the fabricated scaffold was able to support the weight of the human body. No process used to obtain the result was complex or required many resources. The methods and results in this study show several possible clinical applications in fields such as orthopedics or oncology without a need to purchase high-price instruments for 3D printing.

Earth in Space: A CD-ROM Version for Pre-College Teachers

Science.gov (United States)

Pedigo, P.

2003-12-01

Earth in Space, a magazine about the Earth and space sciences for pre-college science teachers, was published by AGU between 1987 and 2001 (9 issues each year). The goal of Earth in Space was to make research at the frontiers of the geosciences accessible to teachers and students and engage them in thinking about scientific careers. Each issue contained two or three recent research articles, rewritten for a high school level audience from the original version published in peer-reviewed AGU journals, which were supplemented with short news items and biographic information about the authors. As part of a 2003 summer internship with AGU, sponsored by the AGU Committee on Education and Human Resources (CEHR) and the American Institute of Physics, this collection of Earth in Space magazines was converted into an easily accessible electronic resource for K-12 teachers and students. Every issue was scanned into a PDF file. The entire collection of articles was cataloged in a database indexed to key topic terms (e.g., volcanoes, global climate change, space weather). A front-page was designed in order to facilitate rapid access to articles concerning specific topics within the Earth and space sciences of particular interest to high school students. A compact CD-ROM version of this resource will be distributed to science teachers at future meetings of the National Science Teachers Association and will be made available through AGU's Outreach and Research Support program.

Will 3D printers manufacture your meals?

NARCIS (Netherlands)

Bommel, K.J.C. van

2013-01-01

These days, 3D printers are laying down plastics, metals, resins, and other materials in whatever configurations creative people can dream up. But when the next 3D printing revolution comes, you'll be able to eat it.

AF-GEOSpace Version 2.0: Space Environment Software Products for 2002

Science.gov (United States)

Hilmer, R. V.; Ginet, G. P.; Hall, T.; Holeman, E.; Tautz, M.

2002-05-01

AF-GEOSpace Version 2.0 (release 2002 on WindowsNT/2000/XP) is a graphics-intensive software program developed by AFRL with space environment models and applications. It has grown steadily to become a development tool for automated space weather visualization products and helps with a variety of tasks: orbit specification for radiation hazard avoidance; satellite design assessment and post-event analysis; solar disturbance effects forecasting; frequency and antenna management for radar and HF communications; determination of link outage regions for active ionospheric conditions; and physics research and education. The object-oriented C++ code is divided into five module classes. Science Modules control science models to give output data on user-specified grids. Application Modules manipulate these data and provide orbit generation and magnetic field line tracing capabilities. Data Modules read and assist with the analysis of user-generated data sets. Graphics Modules enable the display of features such as plane slices, magnetic field lines, line plots, axes, the Earth, stars, and satellites. Worksheet Modules provide commonly requested coordinate transformations and calendar conversion tools. Common input data archive sets, application modules, and 1-, 2-, and 3-D visualization tools are provided to all models. The code documentation includes detailed examples with click-by-click instructions for investigating phenomena that have well known effects on communications and spacecraft systems. AF-GEOSpace Version 2.0 builds on the success of its predecessors. The first release (Version 1.21, 1996/IRIX on SGI) contained radiation belt particle flux and dose models derived from CRRES satellite data, an aurora model, an ionosphere model, and ionospheric HF ray tracing capabilities. Next (Version 1.4, 1999/IRIX on SGI) science modules were added related to cosmic rays and solar protons, low-Earth orbit radiation dosages, single event effects probability maps, ionospheric

PR-EDB: Power Reactor Embrittlement Database Version 3

International Nuclear Information System (INIS)

Wang, Jy-An John; Subramani, Ranjit

2008-01-01

The aging and degradation of light-water reactor pressure vessels is of particular concern because of their relevance to plant integrity and the magnitude of the expected irradiation embrittlement. The radiation embrittlement of reactor pressure vessel materials depends on many factors, such as neutron fluence, flux, and energy spectrum, irradiation temperature, and preirradiation material history and chemical compositions. These factors must be considered to reliably predict pressure vessel embrittlement and to ensure the safe operation of the reactor. Large amounts of data from surveillance capsules are needed to develop a generally applicable damage prediction model that can be used for industry standards and regulatory guides. Furthermore, the investigations of regulatory issues such as vessel integrity over plant life, vessel failure, and sufficiency of current codes, Standard Review Plans (SRPs), and Guides for license renewal can be greatly expedited by the use of a well-designed computerized database. The Power Reactor Embrittlement Database (PR-EDB) is such a comprehensive collection of data for U.S. designed commercial nuclear reactors. The current version of the PR-EDB lists the test results of 104 heat-affected-zone (HAZ) materials, 115 weld materials, and 141 base materials, including 103 plates, 35 forgings, and 3 correlation monitor materials that were irradiated in 321 capsules from 106 commercial power reactors. The data files are given in dBASE format and can be accessed with any personal computer using the Windows operating system. 'User-friendly' utility programs have been written to investigate radiation embrittlement using this database. Utility programs allow the user to retrieve, select and manipulate specific data, display data to the screen or printer, and fit and plot Charpy impact data. The PR-EDB Version 3.0 upgrades Version 2.0. The package was developed based on the Microsoft .NET framework technology and uses Microsoft Access for

PR-EDB: Power Reactor Embrittlement Database - Version 3

Energy Technology Data Exchange (ETDEWEB)

Wang, Jy-An John [ORNL; Subramani, Ranjit [ORNL

2008-03-01

The aging and degradation of light-water reactor pressure vessels is of particular concern because of their relevance to plant integrity and the magnitude of the expected irradiation embrittlement. The radiation embrittlement of reactor pressure vessel materials depends on many factors, such as neutron fluence, flux, and energy spectrum, irradiation temperature, and preirradiation material history and chemical compositions. These factors must be considered to reliably predict pressure vessel embrittlement and to ensure the safe operation of the reactor. Large amounts of data from surveillance capsules are needed to develop a generally applicable damage prediction model that can be used for industry standards and regulatory guides. Furthermore, the investigations of regulatory issues such as vessel integrity over plant life, vessel failure, and sufficiency of current codes, Standard Review Plans (SRPs), and Guides for license renewal can be greatly expedited by the use of a well-designed computerized database. The Power Reactor Embrittlement Database (PR-EDB) is such a comprehensive collection of data for U.S. designed commercial nuclear reactors. The current version of the PR-EDB lists the test results of 104 heat-affected-zone (HAZ) materials, 115 weld materials, and 141 base materials, including 103 plates, 35 forgings, and 3 correlation monitor materials that were irradiated in 321 capsules from 106 commercial power reactors. The data files are given in dBASE format and can be accessed with any personal computer using the Windows operating system. "User-friendly" utility programs have been written to investigate radiation embrittlement using this database. Utility programs allow the user to retrieve, select and manipulate specific data, display data to the screen or printer, and fit and plot Charpy impact data. The PR-EDB Version 3.0 upgrades Version 2.0. The package was developed based on the Microsoft .NET framework technology and uses Microsoft Access for

FABRIKASI TINTA PRINTER BERBAHAN DASAR PIGMEN ORGANIK DARI SAMPAH DAUN

Directory of Open Access Journals (Sweden)

Pradita Ajeng Wiguna

2014-11-01

Full Text Available Sampah menjadi salah satu permasalahan yang belum terselesaikan dalam masyarakat. Salah satu jenis sampah yang jumlahnya melimpah adalah sampah organik berupa dedaunan. Hal ini menuntut cara penanganan alternatif yang kreatif dan inovatif menjadi produk berdaya guna. Sebuah upaya yang dilakukan adalah pemanfaatan sampah daun sebagai pigmen warna organik untuk tinta printer. Pembuatan pigmen warna dilakukan dengan mereduksi sampah daun hingga berbentuk serbuk karbon yang homogen yaitu membakar sampah daun dalam kondisi oksigen rendah kemudian dilakukan proses pencampuran sederhana dengan bahan lain pembuat tinta. Tinta yang dihasilkan diuji transmitansinya dengan memvariasikan massa karbon yaitu dari 1 sampai 6 gram, hasilnya menunjukan bahwa semakin banyak massa karbon ,intensitas cahayanya semakin rendah. Uji laju absorbsi menunjukan bahwa tinta karbon memiliki kelajuan yang hampir sama dengan jenis tinta di pasaran, yaitu 1,04 mm/s. Saat uji kinerja tinta karbon pada printer menunjukan hasil yang lebih hitam dan halus sehingga sesuai jika diaplikasikan sebagai tinta printer.

A desktop 3D printer with dual extruders to produce customised electronic circuitry

Science.gov (United States)

Butt, Javaid; Onimowo, Dominic Adaoiza; Gohrabian, Mohammed; Sharma, Tinku; Shirvani, Hassan

2018-03-01

3D printing has opened new horizons for the manufacturing industry in general, and 3D printers have become the tools for technological advancements. There is a huge divide between the pricing of industrial and desktop 3D printers with the former being on the expensive side capable of producing excellent quality products and latter being on the low-cost side with moderate quality results. However, there is a larger room for improvements and enhancements for the desktop systems as compared to the industrial ones. In this paper, a desktop 3D printer called Prusa Mendel i2 has been modified and integrated with an additional extruder so that the system can work with dual extruders and produce bespoke electronic circuits. The communication between the two extruders has been established by making use of the In-Chip Serial Programming port on the Arduino Uno controlling the printer. The biggest challenge is to control the flow of electric paint (to be dispensed by the new extruder) and CFD (Computational Fluid Dynamics) analysis has been carried out to ascertain the optimal conditions for proper dispensing. The final product is a customised electronic circuit with the base of plastic (from the 3D printer's extruder) and electronic paint (from the additional extruder) properly dispensed to create a live circuit on a plastic platform. This low-cost enhancement to a desktop 3D printer can provide a new prospect to produce multiple material parts where the additional extruder can be filled with any material that can be properly dispensed from its nozzle.

Child-friendly integrated public spaces (RPTRA): Uses and sense of attachment

Science.gov (United States)

Prakoso, S.; Dewi, J.

2018-03-01

The Jakarta City Provincial Government undertook an extensive citywide initiative to build small public urban green spaces, called child-friendly integrated public spaces (RPTRA). Studies on how citizens, including children, use RPTRA was limited, and questions regarding whether children had become attached to the RPTRA as one of their favorite places remain unanswered. This paper presents a preliminary study on ten RPTRA located in Jakarta. We examine how children and citizens use the spaces, based on data from respondents who completed on-site questionnaires during the course of their visit to the RPTRA. We also measure the degree of children’s sense of attachment to RPTRA. The results show that children primarily use RPTRA for playing and learning. Women and girls use RPTRA the most, and elderly citizens use it the least. The results of the study also demonstrate that children had developed a sense of attachment to RPTRA and it had become one of their favorite places. This study may have implications on the existence of small public urban green spaces like RPTRA as valuable assets in the everyday lives of children and citizens. It proposes that RPTRA should be taken into account for future planning of densely populated urban areas.

Modeling And Position Control Of Scara Type 3D Printer

Directory of Open Access Journals (Sweden)

Ahmet Saygamp305n Ogulmuamp351

2015-08-01

Full Text Available In this work a scara robot type 3D printer system is dynamically modeled and position control of the system is realized. For this aim computer aided design model of three degrees of freedom robotic system is created using SolidWorks program then obtained model is exported to MATLABSimMechanics software for position control. Also mathematical model of servo motors used in robotic 3D printer system is included in control methodology to design proportional controllers. Uncontrolled and controlled position results are simulated and given in the form of the graphics.

A phantom production by using 3-dimensional printer and In-vivo dosimetry for a prostate cancer patient

International Nuclear Information System (INIS)

Seo, Jung Nam; Na, Jong Eok; Bae, Sun Myung; Jung, Dong Min; Yoon, In Ha; Bae, Jae Bum; Kwack, Jung Won; Baek, Geum Mun

2015-01-01

The purpose of this study is to evaluate the usefulness of a 3D printed phantom for in-vivo dosimetry of a prostate cancer patient. The phantom is produced to equally describe prostate and rectum based on a 3D volume contour of an actual prostate cancer patient who is treated in Asan Medical Center by using a 3D printer (3D EDISON+, Lokit, Korea). CT(Computed tomography) images of phantom are acquired by computed tomography (Lightspeed CT, GE, USA). By using treatment planning system (Eclipse version 10.0, Varian, USA), treatment planning is established after volume of a prostate cancer patient is compared with volume of the phantom. MOSFET(Metal OXIDE Silicon Field Effect Transistor) is estimated to identify precision and is located in 4 measuring points (bladder, prostate, rectal anterior wall and rectal posterior wall) to analyzed treatment planning and measured value. Prostate volume and rectum volume of prostate cancer patient represent 30.61 cc and 51.19 cc respectively. In case of a phantom, prostate volume and rectum volume represent 31.12 cc and 53.52 cc respectively. A variation of volume between a prostate cancer patient and a phantom is less than 3%. Precision of MOSFET represents less than 3%. It indicates linearity and correlation coefficient indicates from 0.99 - 1.00 depending on dose variation. Each accuracy of bladder, prostate, rectal anterior wall and rectal posterior wall represent 1.4%, 2.6%, 3.7% and 1.5% respectively. In- vivo dosimetry represents entirely less than 5% considering precision of MOSFET. By using a 3D printer, possibility of phantom production based on prostate is verified precision within 3%. effectiveness of In-vivo dosimetry is confirmed from a phantom which is produced by a 3D printer. In-vivo dosimetry is evaluated entirely less than 5% considering precision of MOSFET. Therefore, This study is confirmed the usefulness of a 3D printed phantom for in-vivo dosimetry of a prostate cancer patient. It is necessary to additional

A phantom production by using 3-dimensional printer and In-vivo dosimetry for a prostate cancer patient

Energy Technology Data Exchange (ETDEWEB)

Seo, Jung Nam; Na, Jong Eok; Bae, Sun Myung; Jung, Dong Min; Yoon, In Ha; Bae, Jae Bum; Kwack, Jung Won; Baek, Geum Mun [Dept. of Radiation Oncology, ASAN Medical Center, Seoul (Korea, Republic of)

2015-06-15

The purpose of this study is to evaluate the usefulness of a 3D printed phantom for in-vivo dosimetry of a prostate cancer patient. The phantom is produced to equally describe prostate and rectum based on a 3D volume contour of an actual prostate cancer patient who is treated in Asan Medical Center by using a 3D printer (3D EDISON+, Lokit, Korea). CT(Computed tomography) images of phantom are acquired by computed tomography (Lightspeed CT, GE, USA). By using treatment planning system (Eclipse version 10.0, Varian, USA), treatment planning is established after volume of a prostate cancer patient is compared with volume of the phantom. MOSFET(Metal OXIDE Silicon Field Effect Transistor) is estimated to identify precision and is located in 4 measuring points (bladder, prostate, rectal anterior wall and rectal posterior wall) to analyzed treatment planning and measured value. Prostate volume and rectum volume of prostate cancer patient represent 30.61 cc and 51.19 cc respectively. In case of a phantom, prostate volume and rectum volume represent 31.12 cc and 53.52 cc respectively. A variation of volume between a prostate cancer patient and a phantom is less than 3%. Precision of MOSFET represents less than 3%. It indicates linearity and correlation coefficient indicates from 0.99 - 1.00 depending on dose variation. Each accuracy of bladder, prostate, rectal anterior wall and rectal posterior wall represent 1.4%, 2.6%, 3.7% and 1.5% respectively. In- vivo dosimetry represents entirely less than 5% considering precision of MOSFET. By using a 3D printer, possibility of phantom production based on prostate is verified precision within 3%. effectiveness of In-vivo dosimetry is confirmed from a phantom which is produced by a 3D printer. In-vivo dosimetry is evaluated entirely less than 5% considering precision of MOSFET. Therefore, This study is confirmed the usefulness of a 3D printed phantom for in-vivo dosimetry of a prostate cancer patient. It is necessary to additional

78 FR 32424 - Notice of Issuance of Final Determination Concerning Monochrome Laser Printers

Science.gov (United States)

2013-05-30

... 5200DNG/SP 5210DNG monochrome laser printers for purposes of U.S. Government procurement? LAW AND ANALYSIS... procurement purposes is the United States. Notice of this final determination will be given in the Federal... of certain monochrome laser printers. Based upon the facts presented, CBP has concluded in the final...

Rapid patterning of 'tunable' hydrophobic valves on disposable microchips by laser printer lithography.

Science.gov (United States)

Ouyang, Yiwen; Wang, Shibo; Li, Jingyi; Riehl, Paul S; Begley, Matthew; Landers, James P

2013-05-07

We recently defined a method for fabricating multilayer microdevices using poly(ethylene terephthalate) transparency film and printer toner, and showed these could be successfully applied to DNA extraction and amplification (Duarte et al., Anal. Chem. 2011, 83, 5182-5189). Here, we advance the functionality of these microdevices with flow control enabled by hydrophobic valves patterned using laser printer lithography. Laser printer patterning of toner within the microchannel induces a dramatic change in surface hydrophobicity (change in contact angle of DI water from 51° to 111°) with good reproducibility. Moreover, the hydrophobicity of the surface can be controlled by altering the density of the patterned toner via varying the gray-scale setting on the laser printer, which consequently tunes the valve's burst pressure. Toner density provided a larger burst pressure bandwidth (158 ± 18 Pa to 573 ± 16 Pa) than could be achieved by varying channel geometry (492 ± 18 Pa to 573 ± 16 Pa). Finally, we used a series of tuned toner valves (with varied gray-scale) for passive valve-based fluidic transfer in a predictable manner through the architecture of a rotating PeT microdevice. While an elementary demonstration, this presents the possibility for simplistic and cost-effective microdevices with valved fluid flow control to be fabricated using nothing more than a laser printer, a laser cutter and a laminator.

Direct laser printing using viscous printer's ink

International Nuclear Information System (INIS)

Nasibov, A S; Bagramov, V G; Berezhnoi, K V

2006-01-01

The results of experiments on direct laser printing using viscous printer's ink with the help of a copper vapour laser (CVL)-based device are presented. The highly reflecting CVL cavity mirror was replaced by a spatial mirror modulator (SMM). Viscous printer's ink was used for printing. A pressure pulse produced at the boundary (on which an intensified and diminished image of the SMM was projected) between the ink and a transparency was used for transferring the ink to the plastic card. It was shown that the use of a CVL allowed a maximum printing speed of ∼80 cm 2 s -1 , a resolution of 625 dpi and up to 15 gradations. The dependence of the emission intensity of the element being projected (pixel) on its diameter is studied. It is shown that an increase in the brightness of this element with decreasing its size is caused by the summation of the laser and amplified radiation. (laser applications and other topics in quantum electronics)

Microfluidic impact printer with interchangeable cartridges for versatile non-contact multiplexed micropatterning.

Science.gov (United States)

Ding, Yuzhe; Huang, Eric; Lam, Kit S; Pan, Tingrui

2013-05-21

Biopatterning has been increasingly used for well-defined cellular microenvironment, patterned surface topology, and guided biological cues; however, it meets challenges on biocompatibility, thermal and chemical sensitivity, as well as limited availability of reagents. In this paper, we aim at combining the desired features from non-contact inkjet printing and dot-matrix impact printing to establish a versatile multiplexed micropatterning platform, referred to as Microfluidic Impact Printer (MI-Printer), for emerging biomedical applications. Using this platform, we can achieve the distinct features of no cross-contamination, sub-microliter ink loading with a minimal dead volume, high-throughput printing, biocompatible non-contact processing, sequential patterning with self-alignment, wide adaptability for complex media (e.g., cell suspension or colloidal solutions), interchangeable/disposable cartridge design, and simple assembly and configuration, all highly desirable towards laboratory-based research and development. Specifically, the printing resolution of the MI-printer platform has been experimentally characterized and theoretically analysed. Optimal printing resolution of 80 μm has been repeatedly obtained. Furthermore, two useful functions of the MI-printer, multiplexed printing and combinatorial printing, have been experimentally demonstrated with less than 10 μm misalignment. Moreover, molecular and biological patterning, utilizing the multiplexed and combinatorial printing, has been implemented to illustrate the utility of this versatile printing technique for emerging biomedical applications.

The Role of Original Version Cinema into the European Digital Space

Science.gov (United States)

Ledo-Andión, Margarita; López-Gómez, Antía; Castelló-Mayo, Enrique

2017-01-01

This paper reports the results derived from the research project, entitled "eDCINEMA: Towards the European Digital Space. The role of small cinemas in original version" (CSO2012-35784), which focused on the analysis of the role of movies in OV/OVS in achieving diversity of languages and cultures (as viewed from the European Digital…

Potential usefulness of a video printer for producing secondary images from digitized chest radiographs

Science.gov (United States)

Nishikawa, Robert M.; MacMahon, Heber; Doi, Kunio; Bosworth, Eric

1991-05-01

Communication between radiologists and clinicians could be improved if a secondary image (copy of the original image) accompanied the radiologic report. In addition, the number of lost original radiographs could be decreased, since clinicians would have less need to borrow films. The secondary image should be simple and inexpensive to produce, while providing sufficient image quality for verification of the diagnosis. We are investigating the potential usefulness of a video printer for producing copies of radiographs, i.e. images printed on thermal paper. The video printer we examined (Seikosha model VP-3500) can provide 64 shades of gray. It is capable of recording images up to 1,280 pixels by 1,240 lines and can accept any raster-type video signal. The video printer was characterized in terms of its linearity, contrast, latitude, resolution, and noise properties. The quality of video-printer images was also evaluated in an observer study using portable chest radiographs. We found that observers could confirm up to 90 of the reported findings in the thorax using video- printer images, when the original radiographs were of high quality. The number of verified findings was diminished when high spatial resolution was required (e.g. detection of a subtle pneumothorax) or when a low-contrast finding was located in the mediastinal area or below the diaphragm (e.g. nasogastric tubes).

Analysis of laser printer and photocopier toners by spectral properties and chemometrics

Science.gov (United States)

Verma, Neha; Kumar, Raj; Sharma, Vishal

2018-05-01

The use of printers to generate falsified documents has become a common practice in today's world. The examination and identification of the printed matter in the suspected documents (civil or criminal cases) may provide important information about the authenticity of the document. In the present study, a total number of 100 black toner samples both from laser printers and photocopiers were examined using diffuse reflectance UV-Vis Spectroscopy. The present research is divided into two parts; visual discrimination and discrimination by using multivariate analysis. A comparison between qualitative and quantitative analysis showed that multivariate analysis (Principal component analysis) provides 99.59%pair-wise discriminating power for laser printer toners while 99.84% pair-wise discriminating power for photocopier toners. The overall results obtained confirm the applicability of UV-Vis spectroscopy and chemometrics, in the nondestructive analysis of toner printed documents while enhancing their evidential value for forensic applications.

Plotting of bathythermograph transect data on a printer

Science.gov (United States)

Reynolds, James B.; McLain, Douglas R.

1971-01-01

A program for plotting bathythermograph transect data on a computer (IBM 1130) printer is available from the Great Lakes Fishery Laboratory. Temperature values are printed in positions proportional to their depths and distances from shore. Contour lines are drawn manually through the plotted points.

Occupational and consumer risk estimates for nanoparticles emitted by laser printers

International Nuclear Information System (INIS)

Haenninen, Otto; Brueske-Hohlfeld, Irene; Loh, Miranda; Stoeger, Tobias; Kreyling, Wolfgang; Schmid, Otmar; Peters, Annette

2010-01-01

Several studies have reported laser printers as significant sources of nanosized particles ( -1 ; particle number 1.1-3.1 x 10 9 d -1 ) were estimated to correspond to 4-13 (mass) or 12-34 (number) deaths per million persons exposed on the basis of epidemiological risk estimates for ambient particles. These risks are higher than the generally used definition of acceptable risk of 1 x 10 -6 , but substantially lower than the estimated risks due to ambient particles. Toxicological studies on ambient particles revealed consistent values for lowest observed effect levels (LOELs) which were converted into equivalent daily uptakes using allometric scaling. These LOEL uptakes were by a factor of about 330-1,000 (mass) and 1,000-2,500 (particle surface area) higher than estimated uptakes from printers. This toxicological assessment would indicate no significant health risks due to printer particles. Finally, our study suggests that particle number (not mass) and mass (not surface area) are the most conservative risk metrics for the epidemiological and toxicological risks presented here, respectively.

Psychological and cognitive effects of laser printer emissions: A controlled exposure study.

Science.gov (United States)

Herbig, B; Jörres, R A; Schierl, R; Simon, M; Langner, J; Seeger, S; Nowak, D; Karrasch, S

2018-01-01

The possible impact of ultrafine particles from laser printers on human health is controversially discussed although there are persons reporting substantial symptoms in relation to these emissions. A randomized, single-blinded, cross-over experimental design with two exposure conditions (high-level and low-level exposure) was conducted with 23 healthy subjects, 14 subjects with mild asthma, and 15 persons reporting symptoms associated with laser printer emissions. To separate physiological and psychological effects, a secondary physiologically based categorization of susceptibility to particle effects was used. In line with results from physiological and biochemical assessments, we found no coherent, differential, or clinically relevant effects of different exposure conditions on subjective complaints and cognitive performance in terms of attention, short-term memory, and psychomotor performance. However, results regarding the psychological characteristics of participants and their situational perception confirm differences between the participants groups: Subjects reporting symptoms associated with laser printer emissions showed a higher psychological susceptibility for adverse reactions in line with previous results on persons with multiple chemical sensitivity or idiopathic environmental intolerance. In conclusion, acute psychological and cognitive effects of laser printer emissions were small and could be attributed only to different participant groups but not to differences in exposure conditions in terms of particle number concentrations. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Technique for improving the quality of images from digital cameras using ink-jet printers and smoothed RGB transfer curves

Science.gov (United States)

Sampat, Nitin; Grim, John F.; O'Hara, James E.

1998-04-01

The digital camera market is growing at an explosive rate. At the same time, the quality of photographs printed on ink- jet printers continues to improve. Most of the consumer cameras are designed with the monitor as the target output device and ont the printer. When a user is printing his images from a camera, he/she needs to optimize the camera and printer combination in order to maximize image quality. We describe the details of one such method for improving image quality using a AGFA digital camera and an ink jet printer combination. Using Adobe PhotoShop, we generated optimum red, green and blue transfer curves that match the scene content to the printers output capabilities. Application of these curves to the original digital image resulted in a print with more shadow detail, no loss of highlight detail, a smoother tone scale, and more saturated colors. The image also exhibited an improved tonal scale and visually more pleasing images than those captured and printed without any 'correction'. While we report the results for one camera-printer combination we tested this technique on numbers digital cameras and printer combinations and in each case produced a better looking image. We also discuss the problems we encountered in implementing this technique.

Printing Multistrain Bacterial Patterns with a Piezoelectric Inkjet Printer

Science.gov (United States)

Merrin, Jack; Leibler, Stanislas; Chuang, John S.

2007-01-01

Many studies involving interacting microorganisms would benefit from simple devices able to deposit cells in precisely defined patterns. We describe an inexpensive bacterial piezoelectric inkjet printer (adapted from the design of the POSaM oligonucleotide microarrayer) that can be used to “print out” different strains of bacteria or chemicals in small droplets onto a flat surface at high resolution. The capabilities of this device are demonstrated by printing ordered arrays comprising two bacterial strains labeled with different fluorescent proteins. We also characterized several properties of this piezoelectric printer, such as the droplet volume (of the order of tens of pl), the distribution of number of cells in each droplet, and the dependence of droplet volume on printing frequency. We established the limits of the printing resolution, and determined that the printed viability of Escherichia coli exceeded 98.5%. PMID:17653283

Evaluation of nanoparticle emissions from a laser printer in an experimental chamber and estimation of the human particle dose.

Science.gov (United States)

Serfozo, Norbert; Ondráček, Jakub; Glytsos, Thodoros; Lazaridis, Mihalis

2018-05-01

The aim of this study was to evaluate the nanoparticle emissions from a laser printer in a chamber in conjunction with emissions from printers in a print room (PR) and to characterize the processes that lead to increased nanoparticle concentrations, as well as to estimate the human particle dose of the printers' users. Measurements were conducted in a small stainless steel environmental chamber under controlled conditions, where the evolution of particle size distributions (PSDs) with time and printed pages was studied in detail. Printer was generating nanoparticles (vast majority ˂ 50 nm with mode on ~ 15 nm) primarily during cold startup. Previously, 1-week sampling was also done in a PR at the Technical University of Crete, where the tested laser printer is installed along with three other printers. Similarly, as it was observed in the chamber study, printers' startup on any given day was characterized by a sharp increase in particle number (PN) concentrations. Average measured PN concentrations during printing hours in PR (5.4 × 10 3 #/cm 3 ) is similar to the one observed in chamber measurements (6.7 × 10 3 #/cm 3 ). The ExDoM2 dosimetry model was further applied to calculate the deposition of particles in the human respiratory tract. More precisely, the increase in particle dose for an adult Caucasian male was 14.6- and 24.1-fold at printers' startup, and 1.2- and 5.2-fold during printing in the PR and experimental chamber, respectively, compared to the exposure dose at background concentrations (BCs).

Evaluation of video-printer images as secondary CT images for clinical use

International Nuclear Information System (INIS)

Doi, K.; Rubin, J.

1983-01-01

Video-printer (VP) images of 24 abnormal views from a body CT scanner were made. Although the physical quality of printer images was poor, a group of radiologists and clinicians found that VP images are adequate to confirm the lesion described in the radiology report. The VP images can be used as secondary images, and they can be attached to a report as a part of the radiology service to increase communication between radiologists and clinicians and to prevent the loss of primary images from the radiology file

Cells immobilized on patterns printed in DNA by an inkjet printer.

Science.gov (United States)

Sakurai, Kengo; Teramura, Yuji; Iwata, Hiroo

2011-05-01

The ability to two-dimensionally align various kinds of cells freely onto substrate would be a useful tool for analysis of cell-cell interactions. In this study, we aimed to establish a method for attaching cells to the substrate, in which the pattern is drawn by an inkjet printer. Poly-deoxyribonucleic acid (DNA) was immobilized onto the cell surface by use of DNA-conjugated poly(ethylene) glycol-phospholipid (DNA-PEG-lipid), which is the amphiphilic conjugate of PEG-lipid and single-stranded DNA. The surface of the substrate was then modified with the complementary DNA using an inkjet printer. Finally, DNA-immobilized cells were attached onto the substrate through DNA hybridization. The use of the inkjet printer enabled us to draw the DNA pattern accurately on the substrate with a resolution of a few hundred micrometers. DNA-immobilized cells could be attached precisely along the DNA pattern on the substrate. In addition, various kinds of cells could be attached simultaneously by using various sequences of DNA. Our technique is promising for analysis of cell-cell interactions and differentiation induction in stem cell research. Copyright © 2011 Elsevier Ltd. All rights reserved.

With the advent of domestic 3-dimensional (3D) printers and their associated reduced cost, is it now time for every medical school to have their own 3D printer?

Science.gov (United States)

Balestrini, Christopher; Campo-Celaya, Tatiana

2016-01-01

Anatomy is the backbone of medical education and new techniques to improve learning are frequently explored. With the introduction of 3D printers specifically for the home market, the price of this technology has reached affordable levels. Using patient scan data, accurate 3D models can be printed that represent real human variation in anatomy to provide an innovative, inexpensive and valuable adjunct to anatomical teaching. Is it now time for every medical school to have their own 3D printer?

Response of solvent-exposed printers and unexposed controls to six-hour toluene exposure

DEFF Research Database (Denmark)

Bælum, Jesper; Andersen, I B; Lundqvist, G R

1985-01-01

of intoxication, and irritation of the eyes, nose and throat. Furthermore, the subjects exposed to toluene showed decreased manual dexterity, decreased color discrimination, and decreased accuracy in visual perception. There was no significant difference in the effects of toluene on printers compared to those......The acute effects of toluene were studied in 43 male printers and 43 control subjects matched according to sex, age, educational level, and smoking habits. The mean age of the subjects was 36 (range 29-50) years. The printers had been exposed to solvents for 9 to 25 years during employment at flexo...... and rotogravure printing plants, while the controls had no history of solvent exposure. Each subject was exposed once in a climate chamber to either 100 ppm of toluene or clean air for 6.5 h preceded by a 1-h acclimatization period. The effects of toluene were measured from subjective votes with linear analogue...

Intelligent Fault Diagnosis of Delta 3D Printers Using Attitude Sensors Based on Support Vector Machines

Directory of Open Access Journals (Sweden)

Kun He

2018-04-01

Full Text Available Health condition is a vital factor affecting printing quality for a 3D printer. In this work, an attitude monitoring approach is proposed to diagnose the fault of the delta 3D printer using support vector machines (SVM. An attitude sensor was mounted on the moving platform of the printer to monitor its 3-axial attitude angle, angular velocity, vibratory acceleration and magnetic field intensity. The attitude data of the working printer were collected under different conditions involving 12 fault types and a normal condition. The collected data were analyzed for diagnosing the health condition. To this end, the combination of binary classification, one-against-one with least-square SVM, was adopted for fault diagnosis modelling by using all channels of attitude monitoring data in the experiment. For comparison, each one channel of the attitude monitoring data was employed for model training and testing. On the other hand, a back propagation neural network (BPNN was also applied to diagnose fault using the same data. The best fault diagnosis accuracy (94.44% was obtained when all channels of the attitude monitoring data were used with SVM modelling. The results indicate that the attitude monitoring with SVM is an effective method for the fault diagnosis of delta 3D printers.

Intelligent Fault Diagnosis of Delta 3D Printers Using Attitude Sensors Based on Support Vector Machines.

Science.gov (United States)

He, Kun; Yang, Zhijun; Bai, Yun; Long, Jianyu; Li, Chuan

2018-04-23

Health condition is a vital factor affecting printing quality for a 3D printer. In this work, an attitude monitoring approach is proposed to diagnose the fault of the delta 3D printer using support vector machines (SVM). An attitude sensor was mounted on the moving platform of the printer to monitor its 3-axial attitude angle, angular velocity, vibratory acceleration and magnetic field intensity. The attitude data of the working printer were collected under different conditions involving 12 fault types and a normal condition. The collected data were analyzed for diagnosing the health condition. To this end, the combination of binary classification, one-against-one with least-square SVM, was adopted for fault diagnosis modelling by using all channels of attitude monitoring data in the experiment. For comparison, each one channel of the attitude monitoring data was employed for model training and testing. On the other hand, a back propagation neural network (BPNN) was also applied to diagnose fault using the same data. The best fault diagnosis accuracy (94.44%) was obtained when all channels of the attitude monitoring data were used with SVM modelling. The results indicate that the attitude monitoring with SVM is an effective method for the fault diagnosis of delta 3D printers.

Intelligent Fault Diagnosis of Delta 3D Printers Using Attitude Sensors Based on Support Vector Machines

Science.gov (United States)

He, Kun; Yang, Zhijun; Bai, Yun; Long, Jianyu; Li, Chuan

2018-01-01

Health condition is a vital factor affecting printing quality for a 3D printer. In this work, an attitude monitoring approach is proposed to diagnose the fault of the delta 3D printer using support vector machines (SVM). An attitude sensor was mounted on the moving platform of the printer to monitor its 3-axial attitude angle, angular velocity, vibratory acceleration and magnetic field intensity. The attitude data of the working printer were collected under different conditions involving 12 fault types and a normal condition. The collected data were analyzed for diagnosing the health condition. To this end, the combination of binary classification, one-against-one with least-square SVM, was adopted for fault diagnosis modelling by using all channels of attitude monitoring data in the experiment. For comparison, each one channel of the attitude monitoring data was employed for model training and testing. On the other hand, a back propagation neural network (BPNN) was also applied to diagnose fault using the same data. The best fault diagnosis accuracy (94.44%) was obtained when all channels of the attitude monitoring data were used with SVM modelling. The results indicate that the attitude monitoring with SVM is an effective method for the fault diagnosis of delta 3D printers. PMID:29690641

PEMBUATAN TINTA PRINTER DENGAN PIGMEN ORGANIK BERBAHAN DASAR SAMPAH DAUN

Directory of Open Access Journals (Sweden)

Pradita Ajeng Wiguna

2015-02-01

Full Text Available Waste became one of the unresolved issues in the society. One of the abundant number of waste is organic waste in the form of leaves. The high production of leaf litter on the environment are demanding alternative ways of handling the creative and innovative products useful. An attempt was made is the use of leaf litter as organic color pigments for ink printers. Manufacture of pigments made by reducing the leaf litter to form a homogeneous carbon powder that is burning leaf litter under conditions of low oxygen and then do a simple mixing process with other materials ink makers. The resulting ink tested of transmittance by varying the mass of carbon namely from 1 to 6 grams, the results indicate that the more carbon, the intensity of their light mass is getting low. At the time of adsorbtion rate test showed that carbon ink has almost the same velocity with the type of ink that is circulating in the market, i.e. 1.04 mm/s. Additionally carbon inks have dried faster speed compared to the existing inks on the market, i.e. the ratio of 106: 129 seconds. In the test performance of carbon ink on the printer shows the results that more black and smooth so that appropriate if applied as an inkjet printer.

Laser printer attribution: exploring new features and beyond.

Science.gov (United States)

Ferreira, Anselmo; Navarro, Luiz C; Pinheiro, Giuliano; dos Santos, Jefersson A; Rocha, Anderson

2015-02-01

With a huge amount of printed documents nowadays, identifying their source is useful for criminal investigations and also to authenticate digital copies of a document. In this paper, we propose novel techniques for laser printer attribution. Our solutions do not need very high resolution scanning of the investigated document and explore the multidirectional, multiscale and low-level gradient texture patterns yielded by printing devices. The main contributions of this work are: (1) the description of printed areas using multidirectional and multiscale co-occurring texture patterns; (2) description of texture on low-level gradient areas by a convolution texture gradient filter that emphasizes textures in specific transition areas and (3) the analysis of printer patterns in segments of interest, which we call frames, instead of whole documents or only printed letters. We show by experiments in a well documented dataset that the proposed methods outperform techniques described in the literature and present near-perfect classification accuracy being very promising for deployment in real-world forensic investigations. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Analysis of laser printer and photocopier toners by spectral properties and chemometrics.

Science.gov (United States)

Verma, Neha; Kumar, Raj; Sharma, Vishal

2018-05-05

The use of printers to generate falsified documents has become a common practice in today's world. The examination and identification of the printed matter in the suspected documents (civil or criminal cases) may provide important information about the authenticity of the document. In the present study, a total number of 100 black toner samples both from laser printers and photocopiers were examined using diffuse reflectance UV-Vis Spectroscopy. The present research is divided into two parts; visual discrimination and discrimination by using multivariate analysis. A comparison between qualitative and quantitative analysis showed that multivariate analysis (Principal component analysis) provides 99.59%pair-wise discriminating power for laser printer toners while 99.84% pair-wise discriminating power for photocopier toners. The overall results obtained confirm the applicability of UV-Vis spectroscopy and chemometrics, in the nondestructive analysis of toner printed documents while enhancing their evidential value for forensic applications. Copyright © 2018 Elsevier B.V. All rights reserved.

INK AND CLEANER WASTE REDUCTION EVALUATION FOR FLEXOGRAPHIC PRINTERS

Science.gov (United States)

This report describes the technical and economic effects incurred by a flexographic label printer who changed the type of ink and cleaning agent used in its print shop. The changes were incurred as the best way to eliminate all hazardous materials. The company's corporate managem...

PR-EDB: Power Reactor Embrittlement Data Base, Version 2. Revision 2, Program description

Energy Technology Data Exchange (ETDEWEB)

Stallmann, F.W.; Wang, J.A.; Kam, F.B.K.; Taylor, B.J. [Oak Ridge National Lab., TN (United States)

1994-01-01

Investigations of regulatory issues such as vessel integrity over plant life, vessel failure, and sufficiency of current codes Standard Review Plans (SRP`s) and Guides for license renewal can be greatly expedited by the use of a well-designed computerized data base. Also, such a data base is essential for the validation of embrittlement prediction models by researchers. The Power Reactor Embrittlement Data Base (PR-EDB) is such a comprehensive collection of data for US commercial nuclear reactors. The current version of the PR-EDB contains the Charpy test data that were irradiated in 252 capsules of 96 reactors and consists of 207 data points for heat-affected-zone (HAZ) materials (98 different HAZ), 227 data points for weld materials (105 different welds), 524 data points for base materials (136 different base materials), including 297 plate data points (85 different plates), 119 forging data points (31) different forging), and 108 correlation monitor materials data points (3 different plates). The data files are given in dBASE format and can be accessed with any computer using the DOS operating system. ``User-friendly`` utility programs are used to retrieve and select specific data, manipulate data, display data to the screen or printer, and to fit and plot Charpy impact data. The results of several studies investigated are presented in Appendix D.

Next generation multi-material 3D food printer concept

NARCIS (Netherlands)

Klomp, D.J.; Anderson, P.D.

2017-01-01

3D food printing is a new rapidly developing technology capable of creating food structures that are impossible to create with normal processing techniques. Challenges in this field are creating texture and multi-material food products. To address these challenges a next generation food printer will

Printing method and printer used for applying this method

NARCIS (Netherlands)

2006-01-01

The invention pertains to a method for transferring ink to a receiving material using an inkjet printer having an ink chamber (10) with a nozzle (8) and an electromechanical transducer (16) in cooperative connection with the ink chamber, comprising actuating the transducer to generate a pressure

Development and characterization of an exposure platform suitable for physico-chemical, morphological and toxicological characterization of printer-emitted particles (PEPs).

Science.gov (United States)

Pirela, Sandra V; Pyrgiotakis, Georgios; Bello, Dhimiter; Thomas, Treye; Castranova, Vincent; Demokritou, Philip

2014-06-01

An association between laser printer use and emissions of particulate matter (PM), ozone and volatile organic compounds has been reported in recent studies. However, the detailed physico-chemical, morphological and toxicological characterization of these printer-emitted particles (PEPs) and possible incorporation of engineered nanomaterials into toner formulations remain largely unknown. In this study, a printer exposure generation system suitable for the physico-chemical, morphological, and toxicological characterization of PEPs was developed and used to assess the properties of PEPs from the use of commercially available laser printers. The system consists of a glovebox type environmental chamber for uninterrupted printer operation, real-time and time-integrated particle sampling instrumentation for the size fractionation and sampling of PEPs and an exposure chamber for inhalation toxicological studies. Eleven commonly used laser printers were evaluated and ranked based on their PM emission profiles. Results show PM peak emissions are brand independent and varied between 3000 to 1 300 000 particles/cm³, with modal diameters ranging from 49 to 208 nm, with the majority of PEPs in the nanoscale (printer toner) raises questions about health implications to users. The presented PEGS platform will help in assessing the toxicological profile of PEPs and the link to the physico-chemical and morphological properties of emitted PM and toner formulations.

Effect of print layer height and printer type on the accuracy of 3-dimensional printed orthodontic models.

Science.gov (United States)

Favero, Christian S; English, Jeryl D; Cozad, Benjamin E; Wirthlin, John O; Short, Megan M; Kasper, F Kurtis

2017-10-01

Three-dimensional (3D) printing technologies enable production of orthodontic models from digital files; yet a range of variables associated with the process could impact the accuracy and clinical utility of the models. The objective of this study was to investigate the effect of print layer height on the accuracy of orthodontic models printed 3 dimensionally using a stereolithography format printer and to compare the accuracy of orthodontic models fabricated with several commercially available 3D printers. Thirty-six identical models were produced with a stereolithography-based 3D printer using 3 layer heights (n = 12 per group): 25, 50, and 100 μm. Forty-eight additional models were printed using 4 commercially available 3D printers (n = 12 per group). Each printed model was digitally scanned and compared with the input file via superimposition analysis using a best-fit algorithm to assess accuracy. Statistically significant differences were found in the average overall deviations of models printed at each layer height, with the 25-μm and 100-μm layer height groups having the greatest and least deviations, respectively. Statistically significant differences were also found in the average overall deviations of models produced using the various 3D printer models, but all values fell within clinically acceptable limits. The print layer height and printer model can affect the accuracy of a 3D printed orthodontic model, but the impact should be considered with respect to the clinical tolerances associated with the envisioned application. Copyright © 2017 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Effects of baby-friendly hospital initiative on breast-feeding practices in Sindh

International Nuclear Information System (INIS)

Khan, M.; Akram, D.S.

2013-01-01

To determine changes in the breastfeeding practices of mothers after receiving counseling on Ten Steps to Successful Breastfeeding as defined by the Baby Friendly Hospital Initiative comparing baby friendly hospitals (BFHs) and non-baby-friendly hospitals in Sindh, Pakistan. Methods: The observational study was conducted from June 2007 to June 2009 in randomly selected baby-friendly and non-baby-friendly hospitals of Sindh, Pakistan. Non-probability purposive sampling was employed. The maternity staff was trained on Ten Steps to Successful Breastfeeding. The changes in breastfeeding practices were analysed by SPSS version 15. Results: A total of 236 women were included in the study. Of them, 196 (83.05%) were from baby-friendly hospitals and 40 (16.94%) from non-baby-friendly hospitals. Besides, 174 (88.7%) mothers in baby-friendly hospitals and 5 (12.5%) in non-baby-friendly hospitals during antenatal care received counseling by healthcare providers. There was an increase in breastfeeding practice up to 194 (98.97%) in the first category compared to 12 (30%) in the other category. Conclusion: Counseling under the Baby Friendly Hospital Initiative improved breastfeeding practices up to 98.97% in baby-friendly compared to non-baby-friendly hospitals. (author)

Friends, family and social belonging as we age

Directory of Open Access Journals (Sweden)

2015-09-01

Aims: This study investigated if perceptions of social belonging in late adulthood are differentiated by the quality of family and friend relationships. Method:  The study consisted of two phases.  In Phase 1, 260 university staff and students, aged 18 to 75, completed an online survey investigating the quality of family and friend relationships and their association with social belonging.  In Phase 2, 88 older adults completed a refined print version of the survey.   Results:  Multiple regression was used to analyse the predictive ability of family and friend relationships on social belonging. In Phase 1, significant associations were found between both family and friend relationships and social belonging, with friendship yielding the strongest relationship.  Interestingly, in Phase 2 the association between quality of family and friend relationships and social belonging was mediated by age. Those aged 65 to 74 reported a significant relationship between friends and social belonging, which contrasted with those aged over 75.  A significant association between social belonging and family relationships was also found for the entire cohort aged over 65, while high quality friend relationships enhanced social belonging when family relationships were not strong. Conclusions: These results are tentative, but suggest that future research should consider the role that both friendships and family play in promoting social belonging in older adults.

Development of low-cost open source 3D gel printer "RepRap SWIM-ER"

Science.gov (United States)

Sato, Kei; Basher, Samiul; Ota, Takafumi; Tase, Taishi; Takamatsu, Kyuichiro; Saito, Azusa; Khosla, Ajit; Kawakami, Masaru; Furuawa, Hidemitsu

2017-04-01

Gels are soft and wet materials having low friction, good biocompatibility, and material permeability. It is expected that gel materials will be used as new kinds of industrial materials in the engineering and medical applications. But it cannot build a complicated shape. Soft & Wet Matter Engineering Laboratory developed a 3D gel Printer "SWIM-ER", has enabled modeling of complex shapes of the gel. However, this is expensive. Therefore not all of the gel researchers and the companies have such a device. To solve this problem, we manufacture a low-cost open-source 3D gel printer "RepRap SWIM-ER" from the RepRap. We made the components required to manufacture the "RepRap SWIM-ER" from the 3D printer and chose a light source. In addition, we produced the P-DN gel for RepRap SWIM-ER and conducted the molding test to confirm whether RepRap SWIM-ER can used it.

Low-Cost 3D Printers Enable High-Quality and Automated Sample Preparation and Molecular Detection.

Directory of Open Access Journals (Sweden)

Kamfai Chan

Full Text Available Most molecular diagnostic assays require upfront sample preparation steps to isolate the target's nucleic acids, followed by its amplification and detection using various nucleic acid amplification techniques. Because molecular diagnostic methods are generally rather difficult to perform manually without highly trained users, automated and integrated systems are highly desirable but too costly for use at point-of-care or low-resource settings. Here, we showcase the development of a low-cost and rapid nucleic acid isolation and amplification platform by modifying entry-level 3D printers that cost between $400 and $750. Our modifications consisted of replacing the extruder with a tip-comb attachment that houses magnets to conduct magnetic particle-based nucleic acid extraction. We then programmed the 3D printer to conduct motions that can perform high-quality extraction protocols. Up to 12 samples can be processed simultaneously in under 13 minutes and the efficiency of nucleic acid isolation matches well against gold-standard spin-column-based extraction technology. Additionally, we used the 3D printer's heated bed to supply heat to perform water bath-based polymerase chain reactions (PCRs. Using another attachment to hold PCR tubes, the 3D printer was programmed to automate the process of shuttling PCR tubes between water baths. By eliminating the temperature ramping needed in most commercial thermal cyclers, the run time of a 35-cycle PCR protocol was shortened by 33%. This article demonstrates that for applications in resource-limited settings, expensive nucleic acid extraction devices and thermal cyclers that are used in many central laboratories can be potentially replaced by a device modified from inexpensive entry-level 3D printers.

Resolution enhancement of holographic printer using a hogel overlapping method.

Science.gov (United States)

Hong, Keehoon; Park, Soon-gi; Yeom, Jiwoon; Kim, Jonghyun; Chen, Ni; Pyun, Kyungsuk; Choi, Chilsung; Kim, Sunil; An, Jungkwuen; Lee, Hong-Seok; Chung, U-in; Lee, Byoungho

2013-06-17

We propose a hogel overlapping method for the holographic printer to enhance the lateral resolution of holographic stereograms. The hogel size is directly related to the lateral resolution of the holographic stereogram. Our analysis by computer simulation shows that there is a limit to decreasing the hogel size while printing holographic stereograms. Instead of reducing the size of hogel, the lateral resolution of holographic stereograms can be enhanced by printing overlapped hogels, which makes it possible to take advantage of multiplexing property of the volume hologram. We built a holographic printer, and recorded two holographic stereograms using the conventional and proposed overlapping methods. The images and movies of the holographic stereograms experimentally captured were compared between the conventional and proposed methods. The experimental results confirm that the proposed hogel overlapping method improves the lateral resolution of holographic stereograms compared to the conventional holographic printing method.

Feasibility of Bioprinting with a Modified Desktop 3D Printer.

Science.gov (United States)

Goldstein, Todd A; Epstein, Casey J; Schwartz, John; Krush, Alex; Lagalante, Dan J; Mercadante, Kevin P; Zeltsman, David; Smith, Lee P; Grande, Daniel A

2016-12-01

Numerous studies have shown the capabilities of three-dimensional (3D) printing for use in the medical industry. At the time of this publication, basic home desktop 3D printer kits can cost as little as $300, whereas medical-specific 3D bioprinters can cost more than $300,000. The purpose of this study is to show how a commercially available desktop 3D printer could be modified to bioprint an engineered poly-l-lactic acid scaffold containing viable chondrocytes in a bioink. Our bioprinter was used to create a living 3D functional tissue-engineered cartilage scaffold. In this article, we detail the design, production, and calibration of this bioprinter. In addition, the bioprinted cells were tested for viability, proliferation, biochemistry, and gene expression; these tests showed that the cells survived the printing process, were able to continue dividing, and produce the extracellular matrix expected of chondrocytes.

Incorporating a 3-dimensional printer into the management of early-stage cervical cancer.

Science.gov (United States)

Baek, Min-Hyun; Kim, Dae-Yeon; Kim, Namkug; Rhim, Chae Chun; Kim, Jong-Hyeok; Nam, Joo-Hyun

2016-08-01

We used a 3-dimensional (3D) printer to create anatomical replicas of real lesions and tested its application in cervical cancer. Our study patient decided to undergo radical hysterectomy after seeing her 3D model which was then used to plan and simulate this surgery. Using 3D printers to create patient-specific 3D tumor models may aid cervical cancer patients make treatment decisions. This technology will lead to better surgical and oncological outcomes for cervical cancer patients. J. Surg. Oncol. 2016;114:150-152. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Achieving Child Friendly Justice through Child Friendly Methods: Let’s Start with the Right to Information

Directory of Open Access Journals (Sweden)

Helen Stalford

2017-09-01

Full Text Available Making the justice process ‘child friendly’ is a key priority for the children’s rights community. An abundance of commentary has been produced by the UN Committee on the Rights of the Child to highlight how justice proceedings can be made more accessible for children and, in 2010, the Council of Europe issued its comprehensive ‘Guidelines on Child Friendly Justice’. Despite these efforts, children remain ill-informed, not just about the nature of justice proceedings in which they may be implicated, but about the very existence and scope of their rights and how to enforce them. Despite unequivocal acknowledgement that the availability and accessibility of information is the crucial starting point in a children’s rights-based approach to dispensing justice, there has been surprisingly little attempt to scrutinise the availability, quality and accessibility of information about laws and policies affecting children. This article takes a closer look at what, exactly, ‘child friendly’ information means in practice. In doing so, we argue that attempts to develop child friendly information have yet to progress beyond adult-driven, largely tokenistic and superficial re-branding exercises. As such, efforts to develop child friendly resources are often of limited value in empowering young people to develop their legal literacy and realise their rights in practice. We reflect on our attempt to develop an explicitly children’s rights-based approach to the development of child friendly resources with a view to enhancing their purchase. This took place in the context of a pilot project, commissioned by the Council of Europe in June 2014, to create a child friendly version of their Child Friendly Justice Guidelines.

Oxidative stress and inflammatory response to printer toner particles in human epithelial A549 lung cells.

Science.gov (United States)

Könczöl, Mathias; Weiß, Adilka; Gminski, Richard; Merfort, Irmgard; Mersch-Sundermann, Volker

2013-02-04

Reports on adverse health effects related to occupational exposure to toner powder are still inconclusive. Therefore, we have previously conducted an in vitro-study to characterize the genotoxic potential of three commercially available black printer toner powders in A549 lung cells. In these cell-based assays it was clearly demonstrated that the tested toner powders damage DNA and induce micronucleus (MN) formation. Here, we have studied the cytotoxic and proinflammatory potential of these three types of printer toner particles and the influence of ROS and NF-κB induction in order to unravel the underlying mechanisms. A549 cells were exposed to various concentrations of printer toner particle suspensions for 24 h. The toner particles were observed to exert significant cytotoxic effects in the WST-1 and neutral red (NR)-assays, although to a varying extent. Caspase 3/7 activity increased, while the mitochondrial membrane potential (MMP) was not affected. Particles of all three printer toner powders induced concentration-dependent formation of reactive oxygen species (ROS), as measured in the DCFH-DA assay. Furthermore, toner particle exposure enhanced interleukin-6 and interleukin-8 production, which is in agreement with activation of the transcription factor NF-κB in A549 cells shown by the electrophoretic mobility shift assay (EMSA). Therefore, it can be concluded that exposure of A549 lung cells to three selected printer toner powders caused oxidative stress through induction of ROS. Increased ROS formation may trigger genotoxic effects and activate proinflammatory pathways. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

Inkjet 3D printing of microfluidic structures—on the selection of the printer towards printing your own microfluidic chips

International Nuclear Information System (INIS)

Walczak, Rafał; Adamski, Krzysztof

2015-01-01

This article reports, for the first time, the results of detailed research on the application of inkjet 3D printing for the fabrication of microfluidic structures. CAD designed test structures were printed with four different printers. Dimensional fidelity, shape conformity, and surface roughness were studied for each printout. It was found that the minimum dimension (width or depth) for a properly printed microfluidic channel was approximately 200 μm. Although the nominal resolution of the printers was one order of magnitude better, smaller structures were significantly deformed or not printed at all. It was also found that a crucial step in one-step fabrication of embedded microchannels is the removal of the support material. We also discuss the source of print error and present a way to evaluate other printers. The printouts obtained from the four different printers were compared, and the optimal printing technique and printer were used to fabricate a microfluidic structure for the spectrophotometric characterisation of beverages. UV/VIS absorbance characteristics were collected using this microfluidic structure, demonstrating that the fabricated spectrophotometric chip operated properly. Thus, a proof-of-concept for using inkjet 3D printing for the fabrication of microfluidic structures was obtained. (paper)

Evaluation of 3D Printer Accuracy in Producing Fractal Structure.

Science.gov (United States)

Kikegawa, Kana; Takamatsu, Kyuuichirou; Kawakami, Masaru; Furukawa, Hidemitsu; Mayama, Hiroyuki; Nonomura, Yoshimune

2017-01-01

Hierarchical structures, also known as fractal structures, exhibit advantageous material properties, such as water- and oil-repellency as well as other useful optical characteristics, owing to its self-similarity. Various methods have been developed for producing hierarchical geometrical structures. Recently, fractal structures have been manufactured using a 3D printing technique that involves computer-aided design data. In this study, we confirmed the accuracy of geometrical structures when Koch curve-like fractal structures with zero to three generations were printed using a 3D printer. The fractal dimension was analyzed using a box-counting method. This analysis indicated that the fractal dimension of the third generation hierarchical structure was approximately the same as that of the ideal Koch curve. These findings demonstrate that the design and production of fractal structures can be controlled using a 3D printer. Although the interior angle deviated from the ideal value, the side length could be precisely controlled.

A Personal Desktop Liquid-Metal Printer as a Pervasive Electronics Manufacturing Tool for Society in the Near Future

Directory of Open Access Journals (Sweden)

Jun Yang

2015-12-01

Full Text Available It has long been a dream in the electronics industry to be able to write out electronics directly, as simply as printing a picture onto paper with an office printer. The first-ever prototype of a liquid-metal printer has been invented and demonstrated by our lab, bringing this goal a key step closer. As part of a continuous endeavor, this work is dedicated to significantly extending such technology to the consumer level by making a very practical desktop liquid-metal printer for society in the near future. Through the industrial design and technical optimization of a series of key technical issues such as working reliability, printing resolution, automatic control, human-machine interface design, software, hardware, and integration between software and hardware, a high-quality personal desktop liquid-metal printer that is ready for mass production in industry was fabricated. Its basic features and important technical mechanisms are explained in this paper, along with demonstrations of several possible consumer end-uses for making functional devices such as light-emitting diode (LED displays. This liquid-metal printer is an automatic, easy-to-use, and low-cost personal electronics manufacturing tool with many possible applications. This paper discusses important roles that the new machine may play for a group of emerging needs. The prospective future of this cutting-edge technology is outlined, along with a comparative interpretation of several historical printing methods. This desktop liquid-metal printer is expected to become a basic electronics manufacturing tool for a wide variety of emerging practices in the academic realm, in industry, and in education as well as for individual end-users in the near future.

Printer model for dot-on-dot halftone screens

Science.gov (United States)

Balasubramanian, Raja

1995-04-01

A printer model is described for dot-on-dot halftone screens. For a given input CMYK signal, the model predicts the resulting spectral reflectance of the printed patch. The model is derived in two steps. First, the C, M, Y, K dot growth functions are determined which relate the input digital value to the actual dot area coverages of the colorants. Next, the reflectance of a patch is predicted as a weighted combination of the reflectances of the four solid C, M, Y, K patches and their various overlays. This approach is analogous to the Neugebauer model, with the random mixing equations being replaced by dot-on-dot mixing equations. A Yule-Neilsen correction factor is incorporated to account for light scattering within the paper. The dot area functions and Yule-Neilsen parameter are chosen to optimize the fit to a set of training data. The model is also extended to a cellular framework, requiring additional measurements. The model is tested with a four color xerographic printer employing a line-on-line halftone screen. CIE L*a*b* errors are obtained between measurements and model predictions. The Yule-Neilsen factor significantly decreases the model error. Accuracy is also increased with the use of a cellular framework.

Research on Multioperator silk screen printer Based on Communication Protocol Macro

Directory of Open Access Journals (Sweden)

Zhiming Zhang

2018-01-01

Full Text Available Multioperator silk screen printer is automatic silk screen printing equipment. There are many advantages, such as energy saving, reduce the labor intensity and so on. The control system consists of an intermittent movement main motor and eight color working station printing cycle motion motors. The system controls nine frequency converters through protocol macro communication by using PLC. This paper studies the principle and process characteristics of multioperator silk screen printer. Besides, this paper adopts protocol macro sequence generation method for communication between PLC and frequency converter. This method can control the programming of parameters, such as frequency, operation and monitoring. It also can realize the printing of eight color working stations and monitor the printing status in real time. The practical application proves that the method meets the technical requirements and the reliability is good.

Investigation into the Accuracy of Colours Reproduced by the Ricoh Printer

Directory of Open Access Journals (Sweden)

Andrius Gedvila

2013-02-01

Full Text Available The paper investigates the reproduction accuracy of Ricoh Aficio colour 3006 printer. The study has been conducted analyzing four-color (CMYK gradation curves – the compliance of zonal absorbance with standard references and printing stability of gradation scales. The obtained colours have been measured spectrophotometrically determining the coordinates of colours CIE L*a*b* and differences in colours ΔE. Eight printing regimes and their settings have been examined. It has been found that the printer Ricoh has inaccurately colour grading. However, the quality of colour reproduction is sufficient for printing data not requiring high accuracy of colour reproduction. Colour grading significantly differs from the theoretical approaches, though some regimes (Gamma, Brightness, CMYK simulation allows achieving theoretical values. Despite the high inaccuracy of gradation, differences in colour are not high enough due to corrections made by software.Article in Lithuanian

Atmospheric nonequilibrium mini-plasma jet created by a 3D printer

Energy Technology Data Exchange (ETDEWEB)

Takamatsu, Toshihiro, E-mail: toshihiro@plasma.es.titech.ac.jp [Kobe University Graduate School of Medicine, Department of Gastroenterology, 7-5-1 Kusunoki-cho, Chuo-ku, Kobe, 650-0017 (Japan); Tokyo Institute of Technology, Department of Energy Sciences, J2-32, 4259 Nagatsuta, Midori-ku, Yokohama, 226-8502 (Japan); Kawano, Hiroaki; Miyahara, Hidekazu; Okino, Akitoshi [Tokyo Institute of Technology, Department of Energy Sciences, J2-32, 4259 Nagatsuta, Midori-ku, Yokohama, 226-8502 (Japan); Azuma, Takeshi [Kobe University Graduate School of Medicine, Department of Gastroenterology, 7-5-1 Kusunoki-cho, Chuo-ku, Kobe, 650-0017 (Japan)

2015-07-15

In this study, a small-sized plasma jet source with a 3.7 mm head diameter was created via a 3D printer. The jet’s emission properties and OH radical concentrations (generated by argon, helium, and nitrogen plasmas) were investigated using optical emission spectrometry (OES) and electron spin resonance (ESR). As such, for OES, each individual gas plasma propagates emission lines that derive from gases and ambient air inserted into the measurement system. For the case of ESR, a spin adduct of the OH radical is typically observed for all gas plasma treatment scenarios with a 10 s treatment by helium plasma generating the largest amount of OH radicals at 110 μM. Therefore, it was confirmed that a plasma jet source made by a 3D printer can generate stable plasmas using each of the aforementioned three gases.

MATERIALS COMPATIBILITY STUDY FOR THREE-DIMENSIONAL PRINTER MATERIALS

Science.gov (United States)

2017-09-01

shown that the nanoparticle vapor emitted by a 3D printer can present both environmental and health concerns. A study by the Built Environment...because of the different retention times and spectral features (Figures 10–13). In addition , azacyclotrodecan-2-one (62% confidence level for...to separate the PEG from the rest of the compounds to enhance the ionization. It is possible that in addition to applying a column, other types of

Wearing a training version of the Extravehicular Mobility Unit (EMU) space suit, astronaut Mario

Science.gov (United States)

1995-01-01

STS-77 TRAINING VIEW --- Wearing a training version of the Extravehicular Mobility Unit (EMU) space suit, astronaut Mario Runco, mission specialist, prepares to participate in an underwater rehearsal of a contingency Extravehicular Activity (EVA). This type of training routinely takes place in the 25-feet deep pool of the Johnson Space Centers (JSC) Weightless Environment Training Center (WET-F). The training prepares at least two crew members on each flight for procedures to follow outside the spacecraft in event of failure of remote methods to perform various chores.

Hacking for astronomy: can 3D printers and open-hardware enable low-cost sub-/millimeter instrumentation?

Science.gov (United States)

Ferkinhoff, Carl

2014-07-01

There have been several exciting developments in the technologies commonly used n in the hardware hacking community. Advances in low cost additive-manufacturing processes (i.e. 3D-printers) and the development of openhardware projects, which have produced inexpensive and easily programmable micro-controllers and micro-computers (i.e. Arduino and Raspberry Pi) have opened a new door for individuals seeking to make their own devices. Here we describe the potential for these technologies to reduce costs in construction and development of submillimeter/millimeter astronomical instrumentation. Specifically we have begun a program to measure the optical properties of the custom plastics used in 3D-printers as well as the printer accuracy and resolution to assess the feasibility of directly printing sub- /millimeter transmissive optics. We will also discuss low cost designs for cryogenic temperature measurement and control utilizing Arduino and Raspberry Pi.

Thin-layer scanner with a dot printer recorder for radiolabelled compounds

International Nuclear Information System (INIS)

Kralova, M.; Kysela, F.; Hradil, Z.

1982-01-01

A scanner combined with a matrix printer is described for automatic evaluation of thin-layer radiochromatographs of soft beta emitters such as 3 H, 14 C, and 32 P. Details of the device including block schemes and electrical schemes are given

NASA Space Science Resource Catalog

Science.gov (United States)

Teays, T.

2000-05-01

The NASA Office of Space Science Resource Catalog provides a convenient online interface for finding space science products for use in classrooms, science museums, planetariums, and many other venues. Goals in developing this catalog are: (1) create a cataloging system for all NASA OSS education products, (2) develop a system for characterizing education products which is meaningful to a large clientele, (3) develop a mechanism for evaluating products, (4) provide a user-friendly interface to search and access the data, and (5) provide standardized metadata and interfaces to other cataloging and library systems. The first version of the catalog is being tested at the spring 2000 conventions of the National Science Teachers Association (NSTA) and the National Council of Teachers of Mathematics (NCTM) and will be released in summer 2000. The catalog may be viewed at the Origins Education Forum booth.

A customized bolus produced using a 3-dimensional printer for radiotherapy.

Directory of Open Access Journals (Sweden)

Shin-Wook Kim

Full Text Available OBJECTIVE: Boluses are used in high-energy radiotherapy in order to overcome the skin sparing effect. In practice though, commonly used flat boluses fail to make a perfect contact with the irregular surface of the patient's skin, resulting in air gaps. Hence, we fabricated a customized bolus using a 3-dimensional (3D printer and evaluated its feasibility for radiotherapy. METHODS: We designed two kinds of bolus for production on a 3D printer, one of which was the 3D printed flat bolus for the Blue water phantom and the other was a 3D printed customized bolus for the RANDO phantom. The 3D printed flat bolus was fabricated to verify its physical quality. The resulting 3D printed flat bolus was evaluated by assessing dosimetric parameters such as D1.5 cm, D5 cm, and D10 cm. The 3D printed customized bolus was then fabricated, and its quality and clinical feasibility were evaluated by visual inspection and by assessing dosimetric parameters such as Dmax, Dmin, Dmean, D90%, and V90%. RESULTS: The dosimetric parameters of the resulting 3D printed flat bolus showed that it was a useful dose escalating material, equivalent to a commercially available flat bolus. Analysis of the dosimetric parameters of the 3D printed customized bolus demonstrated that it is provided good dose escalation and good contact with the irregular surface of the RANDO phantom. CONCLUSIONS: A customized bolus produced using a 3D printer could potentially replace commercially available flat boluses.

A customized bolus produced using a 3-dimensional printer for radiotherapy.

Science.gov (United States)

Kim, Shin-Wook; Shin, Hun-Joo; Kay, Chul Seung; Son, Seok Hyun

2014-01-01

Boluses are used in high-energy radiotherapy in order to overcome the skin sparing effect. In practice though, commonly used flat boluses fail to make a perfect contact with the irregular surface of the patient's skin, resulting in air gaps. Hence, we fabricated a customized bolus using a 3-dimensional (3D) printer and evaluated its feasibility for radiotherapy. We designed two kinds of bolus for production on a 3D printer, one of which was the 3D printed flat bolus for the Blue water phantom and the other was a 3D printed customized bolus for the RANDO phantom. The 3D printed flat bolus was fabricated to verify its physical quality. The resulting 3D printed flat bolus was evaluated by assessing dosimetric parameters such as D1.5 cm, D5 cm, and D10 cm. The 3D printed customized bolus was then fabricated, and its quality and clinical feasibility were evaluated by visual inspection and by assessing dosimetric parameters such as Dmax, Dmin, Dmean, D90%, and V90%. The dosimetric parameters of the resulting 3D printed flat bolus showed that it was a useful dose escalating material, equivalent to a commercially available flat bolus. Analysis of the dosimetric parameters of the 3D printed customized bolus demonstrated that it is provided good dose escalation and good contact with the irregular surface of the RANDO phantom. A customized bolus produced using a 3D printer could potentially replace commercially available flat boluses.

In-body tissue-engineered aortic valve (Biovalve type VII) architecture based on 3D printer molding.

Science.gov (United States)

Nakayama, Yasuhide; Takewa, Yoshiaki; Sumikura, Hirohito; Yamanami, Masashi; Matsui, Yuichi; Oie, Tomonori; Kishimoto, Yuichiro; Arakawa, Mamoru; Ohmuma, Kentaro; Tajikawa, Tsutomu; Kanda, Keiichi; Tatsumi, Eisuke

2015-01-01

In-body tissue architecture--a novel and practical regeneration medicine technology--can be used to prepare a completely autologous heart valve, based on the shape of a mold. In this study, a three-dimensional (3D) printer was used to produce the molds. A 3D printer can easily reproduce the 3D-shape and size of native heart valves within several processing hours. For a tri-leaflet, valved conduit with a sinus of Valsalva (Biovalve type VII), the mold was assembled using two conduit parts and three sinus parts produced by the 3D printer. Biovalves were generated from completely autologous connective tissue, containing collagen and fibroblasts, within 2 months following the subcutaneous embedding of the molds (success rate, 27/30). In vitro evaluation, using a pulsatile circulation circuit, showed excellent valvular function with a durability of at least 10 days. Interposed between two expanded polytetrafluoroethylene grafts, the Biovalves (N = 3) were implanted in goats through an apico-aortic bypass procedure. Postoperative echocardiography showed smooth movement of the leaflets with minimal regurgitation under systemic circulation. After 1 month of implantation, smooth white leaflets were observed with minimal thrombus formation. Functional, autologous, 3D-shaped heart valves with clinical application potential were formed following in-body embedding of specially designed molds that were created within several hours by 3D printer. © 2014 Wiley Periodicals, Inc.

Modification of inkjet printer for polymer sensitive layer preparation on silicon-based gas sensors

Directory of Open Access Journals (Sweden)

Tianjian Li

2015-04-01

Full Text Available Inkjet printing is a versatile, low cost deposition technology with the capabilities for the localized deposition of high precision, patterned deposition in a programmable way, and the parallel deposition of a variety of materials. This paper demonstrates a new method of modifying the consumer inkjet printer to prepare polymer-sensitive layers on silicon wafer for gas sensor applications. A special printing tray for the modified inkjet printer to support a 4-inch silicon wafer is designed. The positioning accuracy of the deposition system is tested, based on the newly modified printer. The experimental data show that the positioning errors in the horizontal direction are negligibly small, while the positioning errors in the vertical direction rise with the increase of the printing distance of the wafer. The method for making suitable ink to be deposited to form the polymer-sensitive layer is also discussed. In the testing, a solution of 0.1 wt% polyvinyl alcohol (PVA was used as ink to prepare a sensitive layer with certain dimensions at a specific location on the surface of the silicon wafer, and the results prove the feasibility of the methods presented in this article.

Output of CT images and treatment planning data to a laser printer

International Nuclear Information System (INIS)

Kleinschmidt, C.; Gfirtner, H.; Goetzfried, M.

1992-01-01

We introduce a program for the digital output of CT images with overlaid isodose maps to a laser printer. The high quality prints permit the additional output of treatment planning data on the same sheet. (orig.) [de

From the printer: Potential of three-dimensional printing for orthopaedic applications

NARCIS (Netherlands)

Mok, Sze-Wing; Nizak, Razmara; Fu, Sai-Chuen; Ho, Ki-Wai Kevin; Qin, Ling; Saris, Daniel B. F.; Chan, Kai-Ming; Malda, J

Three-dimensional (3D) printers can create complex structures based on digital models. The combination of medical diagnostic imaging with 3D printing has great potential in day-to-day clinics for patient-specific solutions and applications. In the musculoskeletal system, 3D printing is used to

From the printer: Potential of three-dimensional printing for orthopaedic applications

NARCIS (Netherlands)

Mok, S.; Nizak, R.; Fu, S.C.; Ho, K.K.; Qin, L.; Saris, Daniël B.F.; Chan, K.; Malda, J.

2016-01-01

Three-dimensional (3D) printers can create complex structures based on digital models. The combination of medical diagnostic imaging with 3D printing has great potential in day-to-day clinics for patient-specific solutions and applications. In the musculoskeletal system, 3D printing is used to

FRIEND Engine Framework: a real time neurofeedback client-server system for neuroimaging studies

Science.gov (United States)

Basilio, Rodrigo; Garrido, Griselda J.; Sato, João R.; Hoefle, Sebastian; Melo, Bruno R. P.; Pamplona, Fabricio A.; Zahn, Roland; Moll, Jorge

2015-01-01

In this methods article, we present a new implementation of a recently reported FSL-integrated neurofeedback tool, the standalone version of “Functional Real-time Interactive Endogenous Neuromodulation and Decoding” (FRIEND). We will refer to this new implementation as the FRIEND Engine Framework. The framework comprises a client-server cross-platform solution for real time fMRI and fMRI/EEG neurofeedback studies, enabling flexible customization or integration of graphical interfaces, devices, and data processing. This implementation allows a fast setup of novel plug-ins and frontends, which can be shared with the user community at large. The FRIEND Engine Framework is freely distributed for non-commercial, research purposes. PMID:25688193

FRIEND Engine Framework: A real time neurofeedback client-server system for neuroimaging studies

Directory of Open Access Journals (Sweden)

Rodrigo eBasilio

2015-01-01

Full Text Available In this methods article, we present a new implementation of a recently reported FSL-integrated neurofeedback tool, the standalone version of Functional Real-time Interactive Endogenous Modulation and Decoding (FRIEND. We will refer to this new implementation as the FRIEND Engine Framework. The framework comprises a client-server cross-platform solution for real time fMRI and fMRI/EEG neurofeedback studies, enabling flexible customization or integration of graphical interfaces, devices and data processing. This implementation allows a fast setup of novel plug-ins and frontends, which can be shared with the user community at large. The FRIEND Engine Framework is freely distributed for non-commercial, research purposes.

A PRACTICAL APPROACH TO THE DESIGN AND IMPLEMENTATION OF A LOW COST 3D PRINTER USING OPEN SOURCE TECHNOLOGIES

Directory of Open Access Journals (Sweden)

Stelian-Emilian OLTEAN

2017-12-01

Full Text Available The process of manufacturing parts with additive technologies has seen tremendous growth in recent years, and the emergence of more 3D open source printers has led to complex and personalized shapes at a lower price. For these reasons, 3D printers that form parts by extruding a filament of molten plastic are becoming standard equipment in many laboratories and workshops. In this context, the paper aims to present some theoretical aspects about the implementation and testing of a low cost 3D printer using open source technologies, the description of its main components and the stages to be taken from the 3D modelling of an object to the proper printing.

ITS Version 3.0: Powerful, user-friendly software for radiation modelling

International Nuclear Information System (INIS)

Kensek, R.P.; Halbleib, J.A.; Valdez, G.D.

1993-01-01

ITS (the Integrated Tiger Series) is a powerful, but user-friendly, software package permitting state-of-the-art modelling of electron and/or photon radiation effects. The programs provide Monte Carlo solution of linear time-independent coupled electron/photon radiation transport problems, with or without the presence of macroscopic electric and magnetic fields. The ITS system combines operational simplicity and physical accuracy in order to provide experimentalist and theorists alike with a method for the routine but rigorous solution of sophisticated radiation transport problems

Water-washable ink system reduces printers' hazardous emissions

Energy Technology Data Exchange (ETDEWEB)

Kratch, K.

1994-08-01

Printing industry solvents contain large quantities of volatile organic compounds (VOCs), a major contributor to air pollution in that industry. Because most printing inks contain non-water-soluble petroleum, organic solvents have been necessary to clean presses using those inks. However, under proposed control technique guidelines for lithographic printers issued by the Environmental Protection Agency (EPA), printing-press wash solutions could contain no more than 30% VOCs. Deluxe Corp., a St. Paul, Minn.-based lithographic printer, recognized that stiffer emissions rules could mean harsh penalties for non-compliance and, in 1990, began developing a water-based press wash that would meet the guidelines. Deluxe last year introduced a 100% vegetable oil-based ink that becomes water-washable when exposed to the company's water-based press-wash solution. The solvent-free system eliminates VOCs and hazardous wastes associated with printing, contains no chemicals considered hazardous by EPA, uses no non-renewable resources, and works with existing printing equipment and processes. The system also eliminates water and soil contamination risks associated with laundering or landfilling solvent-saturated shop towels, saves money by eliminating the need to pay for hazardous waste disposal and provides relief to employees who complain about the strong odors of traditional press-wash solvents.

PRODUCTION WITH 3D PRINTERS IN TEXTILES [REVIEW

OpenAIRE

KESKIN Reyhan; GOCEK Ikilem

2015-01-01

3D printers are gaining more attention, finding different applications and 3D printing is being regarded as a ‘revolution’ of the 2010s for production. 3D printing is a production method that produces 3-dimensional objects by combining very thin layers over and over to form the object using 3D scanners or via softwares either private or open source. 3D printed materials find application in a large range of fields including aerospace, automotive, medicine and material science. There are severa...

Graphics-Printing Program For The HP Paintjet Printer

Science.gov (United States)

Atkins, Victor R.

1993-01-01

IMPRINT utility computer program developed to print graphics specified in raster files by use of Hewlett-Packard Paintjet(TM) color printer. Reads bit-mapped images from files on UNIX-based graphics workstation and prints out three different types of images: wire-frame images, solid-color images, and gray-scale images. Wire-frame images are in continuous tone or, in case of low resolution, in random gray scale. In case of color images, IMPRINT also prints by use of default palette of solid colors. Written in C language.

Modern printers and hard copy devices for documentation in nuclear medicine

International Nuclear Information System (INIS)

Mahlstedt, J.

1987-01-01

Modern printers in nuclear medicine comprise technologies such as ink jet print, thermo transfer print or electrostatic plotting in combination with a digital processor. For clinical work these machines provide robust light weight copies within a short time thus fulfilling most of the criteria for an ideal documentation. (orig.) [de

Print preparation of the logical INIS-character set for a digital LNO3 printer

International Nuclear Information System (INIS)

Mueller, M.; Nevyjel, A.

1987-09-01

The implementation of the revised INIS-character set (describedin INIS-Circular Letter No.131) made it necessary to develop a print preparation program, which transfers most of the new INIS logical characters to characters, which are printable on a local LNO3 laser printer. The program is written in PL/I and runs under VAX/VMS on a VAX 11/750. It reads a normal print file and replaces the encoded logical characters by special control sequences, which generate the corresponding images on the LNO3 printer. The program is used for print preparation of any INIS-data records, both input preparation and output tape utilisation on the local VAX system. (Author)

Aerosol Emissions from Fuse-Deposition Modeling 3D Printers in a Chamber and in Real Indoor Environments.

Science.gov (United States)

Vance, Marina E; Pegues, Valerie; Van Montfrans, Schuyler; Leng, Weinan; Marr, Linsey C

2017-09-05

Three-dimensional (3D) printers are known to emit aerosols, but questions remain about their composition and the fundamental processes driving emissions. The objective of this work was to characterize the aerosol emissions from the operation of a fuse-deposition modeling 3D printer. We modeled the time- and size-resolved emissions of submicrometer aerosols from the printer in a chamber study, gained insight into the chemical composition of emitted aerosols using Raman spectroscopy, and measured the potential for exposure to the aerosols generated by 3D printers under real-use conditions in a variety of indoor environments. The average aerosol emission rates ranged from ∼10 8 to ∼10 11 particles min -1 , and the rates varied over the course of a print job. Acrylonitrile butadiene styrene (ABS) filaments generated the largest number of aerosols, and wood-infused polylactic acid (PLA) filaments generated the smallest amount. The emission factors ranged from 6 × 10 8 to 6 × 10 11 per gram of printed part, depending on the type of filament used. For ABS, the Raman spectra of the filament and the printed part were indistinguishable, while the aerosol spectra lacked important peaks corresponding to styrene and acrylonitrile, which are both present in ABS. This observation suggests that aerosols are not a result of volatilization and subsequent nucleation of ABS or direct release of ABS aerosols.

Experimental Validation of Plastic Mandible Models Produced by a "Low-Cost" 3-Dimensional Fused Deposition Modeling Printer.

Science.gov (United States)

Maschio, Federico; Pandya, Mirali; Olszewski, Raphael

2016-03-22

The objective of this study was to investigate the accuracy of 3-dimensional (3D) plastic (ABS) models generated using a low-cost 3D fused deposition modelling printer. Two human dry mandibles were scanned with a cone beam computed tomography (CBCT) Accuitomo device. Preprocessing consisted of 3D reconstruction with Maxilim software and STL file repair with Netfabb software. Then, the data were used to print 2 plastic replicas with a low-cost 3D fused deposition modeling printer (Up plus 2®). Two independent observers performed the identification of 26 anatomic landmarks on the 4 mandibles (2 dry and 2 replicas) with a 3D measuring arm. Each observer repeated the identifications 20 times. The comparison between the dry and plastic mandibles was based on 13 distances: 8 distances less than 12 mm and 5 distances greater than 12 mm. The mean absolute difference (MAD) was 0.37 mm, and the mean dimensional error (MDE) was 3.76%. The MDE decreased to 0.93% for distances greater than 12 mm. Plastic models generated using the low-cost 3D printer UPplus2® provide dimensional accuracies comparable to other well-established rapid prototyping technologies. Validated low-cost 3D printers could represent a step toward the better accessibility of rapid prototyping technologies in the medical field.

MySpace and Facebook: applying the uses and gratifications theory to exploring friend-networking sites.

Science.gov (United States)

Raacke, John; Bonds-Raacke, Jennifer

2008-04-01

The increased use of the Internet as a new tool in communication has changed the way people interact. This fact is even more evident in the recent development and use of friend-networking sites. However, no research has evaluated these sites and their impact on college students. Therefore, the present study was conducted to evaluate: (a) why people use these friend-networking sites, (b) what the characteristics are of the typical college user, and (c) what uses and gratifications are met by using these sites. Results indicated that the vast majority of college students are using these friend-networking sites for a significant portion of their day for reasons such as making new friends and locating old friends. Additionally, both men and women of traditional college age are equally engaging in this form of online communication with this result holding true for nearly all ethnic groups. Finally, results showed that many uses and gratifications are met by users (e.g., "keeping in touch with friends"). Results are discussed in light of the impact that friend-networking sites have on communication and social needs of college students.

Low-Cost 3D Printers Enable High-Quality and Automated Sample Preparation and Molecular Detection

Science.gov (United States)

Chan, Kamfai; Coen, Mauricio; Hardick, Justin; Gaydos, Charlotte A.; Wong, Kah-Yat; Smith, Clayton; Wilson, Scott A.; Vayugundla, Siva Praneeth; Wong, Season

2016-01-01

Most molecular diagnostic assays require upfront sample preparation steps to isolate the target’s nucleic acids, followed by its amplification and detection using various nucleic acid amplification techniques. Because molecular diagnostic methods are generally rather difficult to perform manually without highly trained users, automated and integrated systems are highly desirable but too costly for use at point-of-care or low-resource settings. Here, we showcase the development of a low-cost and rapid nucleic acid isolation and amplification platform by modifying entry-level 3D printers that cost between $400 and $750. Our modifications consisted of replacing the extruder with a tip-comb attachment that houses magnets to conduct magnetic particle-based nucleic acid extraction. We then programmed the 3D printer to conduct motions that can perform high-quality extraction protocols. Up to 12 samples can be processed simultaneously in under 13 minutes and the efficiency of nucleic acid isolation matches well against gold-standard spin-column-based extraction technology. Additionally, we used the 3D printer’s heated bed to supply heat to perform water bath-based polymerase chain reactions (PCRs). Using another attachment to hold PCR tubes, the 3D printer was programmed to automate the process of shuttling PCR tubes between water baths. By eliminating the temperature ramping needed in most commercial thermal cyclers, the run time of a 35-cycle PCR protocol was shortened by 33%. This article demonstrates that for applications in resource-limited settings, expensive nucleic acid extraction devices and thermal cyclers that are used in many central laboratories can be potentially replaced by a device modified from inexpensive entry-level 3D printers. PMID:27362424

The Behavior of Environmentally Friendly Corrosion Preventative Compounds in an Aggressive Coastal Marine Environment

Science.gov (United States)

Montgomery, Eliza L.; Calle, Luz Marina; Curran Jerome C.; Kolody, Mark R.

2013-01-01

The shift to use environmentally friendly technologies throughout future space-related launch programs prompted a study aimed at replacing current petroleum and solvent-based Corrosion Preventive Compounds (CPCs) with environmentally friendly alternatives. The work in this paper focused on the identification and evaluation of environmentally friendly CPCs for use in protecting flight hardware and ground support equipment from atmospheric corrosion. The CPCs, while a temporary protective coating, must survive in the aggressive coastal marine environment that exists throughout the Kennedy Space Center, Florida. The different protection behaviors of fifteen different soft film CPCs, both common petroleum-based and newer environmentally friendly types, were evaluated on various steel and aluminum substrates. The CPC and substrate systems were subjected to atmospheric testing at the Kennedy Space Center's Beachside Atmospheric Corrosion Test Site, as well as cyclic accelerated corrosion testing. Each CPC also underwent physical characterization and launch-related compatibility testing . The initial results for the fifteen CPC systems are reported : Key words: corrosion preventive compound, CPC, spaceport, environmentally friendly, atmospheric exposure, marine, carbon steel, aluminum alloy, galvanic corrosion, wire on bolt.

Development of a stereolithography (STL input and computer numerical control (CNC output algorithm for an entry-level 3-D printer

Directory of Open Access Journals (Sweden)

Brown, Andrew

2014-08-01

Full Text Available This paper presents a prototype Stereolithography (STL file format slicing and tool-path generation algorithm, which serves as a data front-end for a Rapid Prototyping (RP entry- level three-dimensional (3-D printer. Used mainly in Additive Manufacturing (AM, 3-D printers are devices that apply plastic, ceramic, and metal, layer by layer, in all three dimensions on a flat surface (X, Y, and Z axis. 3-D printers, unfortunately, cannot print an object without a special algorithm that is required to create the Computer Numerical Control (CNC instructions for printing. An STL algorithm therefore forms a critical component for Layered Manufacturing (LM, also referred to as RP. The purpose of this study was to develop an algorithm that is capable of processing and slicing an STL file or multiple files, resulting in a tool-path, and finally compiling a CNC file for an entry-level 3- D printer. The prototype algorithm was implemented for an entry-level 3-D printer that utilises the Fused Deposition Modelling (FDM process or Solid Freeform Fabrication (SFF process; an AM technology. Following an experimental method, the full data flow path for the prototype algorithm was developed, starting with STL data files, and then processing the STL data file into a G-code file format by slicing the model and creating a tool-path. This layering method is used by most 3-D printers to turn a 2-D object into a 3-D object. The STL algorithm developed in this study presents innovative opportunities for LM, since it allows engineers and architects to transform their ideas easily into a solid model in a fast, simple, and cheap way. This is accomplished by allowing STL models to be sliced rapidly, effectively, and without error, and finally to be processed and prepared into a G-code print file.

Characterization of solid UV curable 3D printer resins for biological applications

KAUST Repository

Sivashankar, Shilpa; Agambayev, Sumeyra; Buttner, Ulrich; Salama, Khaled N.

2016-01-01

to agglutinate. Six different types of 3D printer resins were compared to test the biocompatibility. The study showed that only few among them could be used for fabrication of micro channels and that had least effect on biological molecules that could be used

Raman spectroscopy and capillary electrophoresis applied to forensic colour inkjet printer inks analysis.

Science.gov (United States)

Król, Małgorzata; Karoly, Agnes; Kościelniak, Paweł

2014-09-01

Forensic laboratories are increasingly engaged in the examination of fraudulent documents, and what is important, in many cases these are inkjet-printed documents. That is why systematic approaches to inkjet printer inks comparison and identification have been carried out by both non-destructive and destructive methods. In this study, micro-Raman spectroscopy and capillary electrophoresis (CE) were applied to the analysis of colour inkjet printer inks. Micro-Raman spectroscopy was used to study the chemical composition of colour inks in situ on a paper surface. It helps to characterize and differentiate inkjet inks, and can be used to create a spectra database of inks taken from different cartridge brands and cartridge numbers. Capillary electrophoresis in micellar electrophoretic capillary chromatography mode was applied to separate colour and colourless components of inks, enabling group identification of those components which occur in a sufficient concentration (giving intensive peaks). Finally, on the basis of the obtained results, differentiation of the analysed inks was performed. Twenty-three samples of inkjet printer inks were examined and the discriminating power (DP) values for both presented methods were established in the routine work of experts during the result interpretation step. DP was found to be 94.0% (Raman) and 95.6% (CE) when all the analysed ink samples were taken into account, and it was 96.7% (Raman) and 98.4% (CE), when only cartridges with different index numbers were considered. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Effectiveness of the Friends for Life Program in Portuguese Schools: Study with a Sample of Highly Anxious Children

Science.gov (United States)

Pereira, Ana Isabel; Marques, Teresa; Russo, Vanessa; Barros, Luísa; Barrett, P.

2014-01-01

The FRIENDS for Life program is a cognitive-behavioral group program that targets anxiety in children. The main purpose of this study was to analyze the effectiveness of the Portuguese version of the FRIENDS for Life Program, which was implemented in schools to reduce anxiety problems in a group of highly anxious children. The study used a…

3D Printers Can Provide an Added Dimension for Teaching Structure-Energy Relationships

Science.gov (United States)

Blauch, David N.; Carroll, Felix A.

2014-01-01

A 3D printer is used to prepare a variety of models representing potential energy as a function of two geometric coordinates. These models facilitate the teaching of structure-energy relationships in molecular conformations and in chemical reactions.

Analisa Eco-friendly Attitudes Dan Eco-friendly Behavior Terhadap Eco-friendly Intention Green Hotel Di Indonesia

OpenAIRE

Silvia, Lanny; Rudijanto, Diana Gabriela; Kristanti, Monika

2017-01-01

Kesadaran masyarakat akan lingkungan yang semakin meningkat membuat masyarakat gencar mencari hotel yang ramah lingkungan dibandingkan dengan hotel konvensional. Penelitian ini bertujuan untuk mengetahui perbedaan eco-friendly attitude, eco- friendly behavior, dan eco-friendly intention konsumen generasi x dan generasi y terhadap green hotel di Indonesia dan apakah eco-friendly attitudes dan eco-friendly behavior berpengaruh signifikan terhadap eco-friendly intention. Total responden dalam pe...

Clinical Application of Solid Model Based on Trabecular Tibia Bone CT Images Created by 3D Printer.

Science.gov (United States)

Cho, Jaemo; Park, Chan-Soo; Kim, Yeoun-Jae; Kim, Kwang Gi

2015-07-01

The aim of this work is to use a 3D solid model to predict the mechanical loads of human bone fracture risk associated with bone disease conditions according to biomechanical engineering parameters. We used special image processing tools for image segmentation and three-dimensional (3D) reconstruction to generate meshes, which are necessary for the production of a solid model with a 3D printer from computed tomography (CT) images of the human tibia's trabecular and cortical bones. We examined the defects of the mechanism for the tibia's trabecular bones. Image processing tools and segmentation techniques were used to analyze bone structures and produce a solid model with a 3D printer. These days, bio-imaging (CT and magnetic resonance imaging) devices are able to display and reconstruct 3D anatomical details, and diagnostics are becoming increasingly vital to the quality of patient treatment planning and clinical treatment. Furthermore, radiographic images are being used to study biomechanical systems with several aims, namely, to describe and simulate the mechanical behavior of certain anatomical systems, to analyze pathological bone conditions, to study tissues structure and properties, and to create a solid model using a 3D printer to support surgical planning and reduce experimental costs. These days, research using image processing tools and segmentation techniques to analyze bone structures to produce a solid model with a 3D printer is rapidly becoming very important.

Development of modular control software for construction 3D-printer

Science.gov (United States)

Bazhanov, A.; Yudin, D.; Porkhalo, V.

2018-03-01

This article discusses the approach to developing modular software for real-time control of an industrial construction 3D printer. The proposed structure of a two-level software solution is implemented for a robotic system that moves in a Cartesian coordinate system with multi-axis interpolation. An algorithm for the formation and analysis of a path is considered to enable the most effective control of printing through dynamic programming.

Accuracy of three-dimensional, paper-based models generated using a low-cost, three-dimensional printer.

Science.gov (United States)

Olszewski, Raphael; Szymor, Piotr; Kozakiewicz, Marcin

2014-12-01

Our study aimed to determine the accuracy of a low-cost, paper-based 3D printer by comparing a dry human mandible to its corresponding three-dimensional (3D) model using a 3D measuring arm. One dry human mandible and its corresponding printed model were evaluated. The model was produced using DICOM data from cone beam computed tomography. The data were imported into Maxilim software, wherein automatic segmentation was performed, and the STL file was saved. These data were subsequently analysed, repaired, cut and prepared for printing with netfabb software. These prepared data were used to create a paper-based model of a mandible with an MCor Matrix 300 printer. Seventy-six anatomical landmarks were chosen and measured 20 times on the mandible and the model using a MicroScribe G2X 3D measuring arm. The distances between all the selected landmarks were measured and compared. Only landmarks with a point inaccuracy less than 30% were used in further analyses. The mean absolute difference for the selected 2016 measurements was 0.36 ± 0.29 mm. The mean relative difference was 1.87 ± 3.14%; however, the measurement length significantly influenced the relative difference. The accuracy of the 3D model printed using the paper-based, low-cost 3D Matrix 300 printer was acceptable. The average error was no greater than that measured with other types of 3D printers. The mean relative difference should not be considered the best way to compare studies. The point inaccuracy methodology proposed in this study may be helpful in future studies concerned with evaluating the accuracy of 3D rapid prototyping models. Copyright © 2014 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Experimental Validation of Plastic Mandible Models Produced by a “Low-Cost” 3-Dimensional Fused Deposition Modeling Printer

Science.gov (United States)

Maschio, Federico; Pandya, Mirali; Olszewski, Raphael

2016-01-01

Background The objective of this study was to investigate the accuracy of 3-dimensional (3D) plastic (ABS) models generated using a low-cost 3D fused deposition modelling printer. Material/Methods Two human dry mandibles were scanned with a cone beam computed tomography (CBCT) Accuitomo device. Preprocessing consisted of 3D reconstruction with Maxilim software and STL file repair with Netfabb software. Then, the data were used to print 2 plastic replicas with a low-cost 3D fused deposition modeling printer (Up plus 2®). Two independent observers performed the identification of 26 anatomic landmarks on the 4 mandibles (2 dry and 2 replicas) with a 3D measuring arm. Each observer repeated the identifications 20 times. The comparison between the dry and plastic mandibles was based on 13 distances: 8 distances less than 12 mm and 5 distances greater than 12 mm. Results The mean absolute difference (MAD) was 0.37 mm, and the mean dimensional error (MDE) was 3.76%. The MDE decreased to 0.93% for distances greater than 12 mm. Conclusions Plastic models generated using the low-cost 3D printer UPplus2® provide dimensional accuracies comparable to other well-established rapid prototyping technologies. Validated low-cost 3D printers could represent a step toward the better accessibility of rapid prototyping technologies in the medical field. PMID:27003456

ANALYSIS OF PRINTING PARAMETERS FOR PRODUCTION OF COMPONENTS WITH ​EASY3DMAKER​ PRINTER

Directory of Open Access Journals (Sweden)

Alexander Rengevič

2016-12-01

Full Text Available The presented article deals with analyses and testing appropriate parameters for the production of components manufactured with rapid prototyping technology - Easy3DMaker printer. The quality of the printed component with a specific shape is analyzed. The analyzed materials are ABS Printplus and PLA Printplus. These materials are printed at different temperatures and speeds. combinations of different settings were tested in order to find the best conditions for printing with different nozzles. The quality of individual printed samples is assessed visually and by touch. The efficiency in terms of print time under various conditions was also analyzed. The main benefit of testing is the establishment of appropriate conditions for printing components on a Easy3DMaker printer. The article does not focus on mechanical properties of the examined samples.

The feasibility of producing patient-specific acrylic cranioplasty implants with a low-cost 3D printer.

Science.gov (United States)

Tan, Eddie T W; Ling, Ji Min; Dinesh, Shree Kumar

2016-05-01

OBJECT Commercially available, preformed patient-specific cranioplasty implants are anatomically accurate but costly. Acrylic bone cement is a commonly used alternative. However, the manual shaping of the bone cement is difficult and may not lead to a satisfactory implant in some cases. The object of this study was to determine the feasibility of fabricating molds using a commercial low-cost 3D printer for the purpose of producing patient-specific acrylic cranioplasty implants. METHODS Using data from a high-resolution brain CT scan of a patient with a calvarial defect posthemicraniectomy, a skull phantom and a mold were generated with computer software and fabricated with the 3D printer using the fused deposition modeling method. The mold was used as a template to shape the acrylic implant, which was formed via a polymerization reaction. The resulting implant was fitted to the skull phantom and the cranial index of symmetry was determined. RESULTS The skull phantom and mold were successfully fabricated with the 3D printer. The application of acrylic bone cement to the mold was simple and straightforward. The resulting implant did not require further adjustment or drilling prior to being fitted to the skull phantom. The cranial index of symmetry was 96.2% (the cranial index of symmetry is 100% for a perfectly symmetrical skull). CONCLUSIONS This study showed that it is feasible to produce patient-specific acrylic cranioplasty implants with a low-cost 3D printer. Further studies are required to determine applicability in the clinical setting. This promising technique has the potential to bring personalized medicine to more patients around the world.

Computational modeling of particle transport and distribution emitted from a Laserjet printer in a ventilated room with different ventilation configurations

International Nuclear Information System (INIS)

Ansaripour, Mehrzad; Abdolzadeh, Morteza; Sargazizadeh, Saleh

2016-01-01

Highlights: • The distribution of emitted particles form a laserjet printer was studied in the breathing zone. • Effects of different ventilation configurations on the breathing zone concentration were investigated. • Mixing ventilation system has a low mean particle concentration in the breathing zone. - Abstract: In the present research, computational modeling of particle transport and distribution emitted from a Laserjet printer was carried out in a ventilated room. A seated manikin was integrated into the study room and the manikin was evaluated in two cases: heated and unheated. Effects of different ventilation configurations of the room on the particle distribution were studied, including three displacement ventilation systems and a mixing ventilation system. The printer was located on different sides of the manikin and the particle concentrations in the breathing zone of the manikin due to the printer’s particles were evaluated in all the ventilation configurations. The averaged particle concentration in the breathing zone of the manikin was calculated and validated with the experimental and numerical data available in the literature. The results of the present study showed that in case of the heated manikin, the particle concentration due to the printer pollutants is significant in the breathing zone of the manikin. The results also showed that when the printer is located on the front side of the manikin, the particle concentration in the breathing zone is quite high in most of the used ventilation configurations. Furthermore, it was found that the mixing ventilation system has a lower mean particle concentration in the breathing zone compared to the most displacement ventilation systems.

Design and Fabrication of an Experimental Microheater Array Powder Sintering Printer

Science.gov (United States)

Holt, Nicholas; Zhou, Wenchao

2018-03-01

Microheater array powder sintering (MAPS) is a novel additive manufacturing process that uses an array of microheaters to selectively sinter powder particles. MAPS shows great promise as a new method of printing flexible electronics by enabling digital curing of conductive inks on a variety of substrates. For MAPS to work effectively, a microscale air gap needs to be maintained between the heater array and the conductive ink. In this article, we present an experimental MAPS printer with air gap control for printing conductive circuits. First, we discuss design aspects necessary to implement MAPS. An analysis is performed to validate that the design can maintain the desired air gap between the microheaters and the sintering layer, which consists of a silver nanoparticle ink. The printer is tested by printing conductive lines on a flexible plastic substrate with silver nanoparticle ink. Results show MAPS performs on par with or better than the existing fabrication methods for printed electronics in terms of both the print quality (conductivity of the printed line) and print speed, which shows MAPS' great promise as a competitive new method for digital production of printed electronics.

3-D Printers Spread from Engineering Departments to Designs across Disciplines

Science.gov (United States)

Chen, Angela

2012-01-01

The ability to print a 3-D object may sound like science fiction, but it has been around in some form since the 1980s. Also called rapid prototyping or additive manufacturing, the idea is to take a design from a computer file and forge it into an object, often in flat cross-sections that can be assembled into a larger whole. While the printer on…

Creating transient cell membrane pores using a standard inkjet printer.

Science.gov (United States)

Owczarczak, Alexander B; Shuford, Stephen O; Wood, Scott T; Deitch, Sandra; Dean, Delphine

2012-03-16

Bioprinting has a wide range of applications and significance, including tissue engineering, direct cell application therapies, and biosensor microfabrication. Recently, thermal inkjet printing has also been used for gene transfection. The thermal inkjet printing process was shown to temporarily disrupt the cell membranes without affecting cell viability. The transient pores in the membrane can be used to introduce molecules, which would otherwise be too large to pass through the membrane, into the cell cytoplasm. The application being demonstrated here is the use of thermal inkjet printing for the incorporation of fluorescently labeled g-actin monomers into cells. The advantage of using thermal ink-jet printing to inject molecules into cells is that the technique is relatively benign to cells. Cell viability after printing has been shown to be similar to standard cell plating methods. In addition, inkjet printing can process thousands of cells in minutes, which is much faster than manual microinjection. The pores created by printing have been shown to close within about two hours. However, there is a limit to the size of the pore created (~10 nm) with this printing technique, which limits the technique to injecting cells with small proteins and/or particles. A standard HP DeskJet 500 printer was modified to allow for cell printing. The cover of the printer was removed and the paper feed mechanism was bypassed using a mechanical lever. A stage was created to allow for placement of microscope slides and coverslips directly under the print head. Ink cartridges were opened, the ink was removed and they were cleaned prior to use with cells. The printing pattern was created using standard drawing software, which then controlled the printer through a simple print command. 3T3 fibroblasts were grown to confluence, trypsinized, and then resuspended into phosphate buffered saline with soluble fluorescently labeled g-actin monomers. The cell suspension was pipetted into the

A desktop 3D printer in safety-critical Java

DEFF Research Database (Denmark)

Strøm, Tórur Biskopstø; Schoeberl, Martin

2012-01-01

there exist several safety-critical Java framework implementations, there is a lack of safety-critical use cases implemented according to the specification. In this paper we present a 3D printer and its safety-critical Java level 1 implementation as a use case. With basis in the implementation we evaluate......It is desirable to bring Java technology to safety-critical systems. To this end The Open Group has created the safety-critical Java specification, which will allow Java applications, written according to the specification, to be certifiable in accordance with safety-critical standards. Although...

Anatomical Reproducibility of a Head Model Molded by a Three-dimensional Printer.

Science.gov (United States)

Kondo, Kosuke; Nemoto, Masaaki; Masuda, Hiroyuki; Okonogi, Shinichi; Nomoto, Jun; Harada, Naoyuki; Sugo, Nobuo; Miyazaki, Chikao

2015-01-01

We prepared rapid prototyping models of heads with unruptured cerebral aneurysm based on image data of computed tomography angiography (CTA) using a three-dimensional (3D) printer. The objective of this study was to evaluate the anatomical reproducibility and accuracy of these models by comparison with the CTA images on a monitor. The subjects were 22 patients with unruptured cerebral aneurysm who underwent preoperative CTA. Reproducibility of the microsurgical anatomy of skull bone and arteries, the length and thickness of the main arteries, and the size of cerebral aneurysm were compared between the CTA image and rapid prototyping model. The microsurgical anatomy and arteries were favorably reproduced, apart from a few minute regions, in the rapid prototyping models. No significant difference was noted in the measured lengths of the main arteries between the CTA image and rapid prototyping model, but errors were noted in their thickness (p printer. It was concluded that these models are useful tools for neurosurgical simulation. The thickness of the main arteries and size of cerebral aneurysm should be comprehensively judged including other neuroimaging in consideration of errors.

Fracture network created by 3D printer and its validation using CT images

Science.gov (United States)

Suzuki, A.; Watanabe, N.; Li, K.; Horne, R. N.

2017-12-01

Understanding flow mechanisms in fractured media is essential for geoscientific research and geological development industries. This study used 3D printed fracture networks in order to control the properties of fracture distributions inside the sample. The accuracy and appropriateness of creating samples by the 3D printer was investigated by using a X-ray CT scanner. The CT scan images suggest that the 3D printer is able to reproduce complex three-dimensional spatial distributions of fracture networks. Use of hexane after printing was found to be an effective way to remove wax for the post-treatment. Local permeability was obtained by the cubic law and used to calculate the global mean. The experimental value of the permeability was between the arithmetic and geometric means of the numerical results, which is consistent with conventional studies. This methodology based on 3D printed fracture networks can help validate existing flow modeling and numerical methods.

Fabrication of low cost soft tissue prostheses with the desktop 3D printer.

Science.gov (United States)

He, Yong; Xue, Guang-huai; Fu, Jian-zhong

2014-11-27

Soft tissue prostheses such as artificial ear, eye and nose are widely used in the maxillofacial rehabilitation. In this report we demonstrate how to fabricate soft prostheses mold with a low cost desktop 3D printer. The fabrication method used is referred to as Scanning Printing Polishing Casting (SPPC). Firstly the anatomy is scanned with a 3D scanner, then a tissue casting mold is designed on computer and printed with a desktop 3D printer. Subsequently, a chemical polishing method is used to polish the casting mold by removing the staircase effect and acquiring a smooth surface. Finally, the last step is to cast medical grade silicone into the mold. After the silicone is cured, the fine soft prostheses can be removed from the mold. Utilizing the SPPC method, soft prostheses with smooth surface and complicated structure can be fabricated at a low cost. Accordingly, the total cost of fabricating ear prosthesis is about $30, which is much lower than the current soft prostheses fabrication methods.

Fracture network created by 3-D printer and its validation using CT images

Science.gov (United States)

Suzuki, Anna; Watanabe, Noriaki; Li, Kewen; Horne, Roland N.

2017-07-01

Understanding flow mechanisms in fractured media is essential for geoscientific research and geological development industries. This study used 3-D printed fracture networks in order to control the properties of fracture distributions inside the sample. The accuracy and appropriateness of creating samples by the 3-D printer was investigated by using a X-ray CT scanner. The CT scan images suggest that the 3-D printer is able to reproduce complex three-dimensional spatial distributions of fracture networks. Use of hexane after printing was found to be an effective way to remove wax for the posttreatment. Local permeability was obtained by the cubic law and used to calculate the global mean. The experimental value of the permeability was between the arithmetic and geometric means of the numerical results, which is consistent with conventional studies. This methodology based on 3-D printed fracture networks can help validate existing flow modeling and numerical methods.

International Space Station (ISS) 3D Printer Performance and Material Characterization Methodology

Science.gov (United States)

Bean, Q. A.; Cooper, K. G.; Edmunson, J. E.; Johnston, M. M.; Werkheiser, M. J.

2015-01-01

In order for human exploration of the Solar System to be sustainable, manufacturing of necessary items on-demand in space or on planetary surfaces will be a requirement. As a first step towards this goal, the 3D Printing In Zero-G (3D Print) technology demonstration made the first items fabricated in space on the International Space Station. From those items, and comparable prints made on the ground, information about the microgravity effects on the printing process can be determined. Lessons learned from this technology demonstration will be applicable to other in-space manufacturing technologies, and may affect the terrestrial manufacturing industry as well. The flight samples were received at the George C. Marshall Space Flight Center on 6 April 2015. These samples will undergo a series of tests designed to not only thoroughly characterize the samples, but to identify microgravity effects manifested during printing by comparing their results to those of samples printed on the ground. Samples will be visually inspected, photographed, scanned with structured light, and analyzed with scanning electron microscopy. Selected samples will be analyzed with computed tomography; some will be assessed using ASTM standard tests. These tests will provide the information required to determine the effects of microgravity on 3D printing in microgravity.

Learning from Your Network of Friends: A Trajectory Representation Learning Model Based on Online Social Ties

KAUST Repository

Alharbi, Basma Mohammed; Zhang, Xiangliang

2017-01-01

Location-Based Social Networks (LBSNs) capture individuals whereabouts for a large portion of the population. To utilize this data for user (location)-similarity based tasks, one must map the raw data into a low-dimensional uniform feature space. However, due to the nature of LBSNs, many users have sparse and incomplete check-ins. In this work, we propose to overcome this issue by leveraging the network of friends, when learning the new feature space. We first analyze the impact of friends on individuals's mobility, and show that individuals trajectories are correlated with thoseof their friends and friends of friends (2-hop friends) in an online setting. Based on our observation, we propose a mixed-membership model that infers global mobility patterns from users' check-ins and their network of friends, without impairing the model's complexity. Our proposed model infers global patterns and learns new representations for both usersand locations simultaneously. We evaluate the inferred patterns and compare the quality of the new user representation against baseline methods on a social link prediction problem.

Learning from Your Network of Friends: A Trajectory Representation Learning Model Based on Online Social Ties

KAUST Repository

Alharbi, Basma Mohammed

2017-02-07

Location-Based Social Networks (LBSNs) capture individuals whereabouts for a large portion of the population. To utilize this data for user (location)-similarity based tasks, one must map the raw data into a low-dimensional uniform feature space. However, due to the nature of LBSNs, many users have sparse and incomplete check-ins. In this work, we propose to overcome this issue by leveraging the network of friends, when learning the new feature space. We first analyze the impact of friends on individuals\\'s mobility, and show that individuals trajectories are correlated with thoseof their friends and friends of friends (2-hop friends) in an online setting. Based on our observation, we propose a mixed-membership model that infers global mobility patterns from users\\' check-ins and their network of friends, without impairing the model\\'s complexity. Our proposed model infers global patterns and learns new representations for both usersand locations simultaneously. We evaluate the inferred patterns and compare the quality of the new user representation against baseline methods on a social link prediction problem.

Using 3D Printers to Model Earth Surface Topography for Increased Student Understanding and Retention

Science.gov (United States)

Thesenga, David; Town, James

2014-05-01

In February 2000, the Space Shuttle Endeavour flew a specially modified radar system during an 11-day mission. The purpose of the multinational Shuttle Radar Topography Mission (SRTM) was to "obtain elevation data on a near-global scale to generate the most complete high-resolution digital topographic database of Earth" by using radar interferometry. The data and resulting products are now publicly available for download and give a view of the landscape removed of vegetation, buildings, and other structures. This new view of the Earth's topography allows us to see previously unmapped or poorly mapped regions of the Earth as well as providing a level of detail that was previously unknown using traditional topographic mapping techniques. Understanding and appreciating the geographic terrain is a complex but necessary requirement for middle school aged (11-14yo) students. Abstract in nature, topographic maps and other 2D renderings of the Earth's surface and features do not address the inherent spatial challenges of a concrete-learner and traditional methods of teaching can at times exacerbate the problem. Technological solutions such as 3D-imaging in programs like Google Earth are effective but lack the tactile realness that can make a large difference in learning comprehension and retention for these young students. First developed in the 1980's, 3D printers were not commercial reality until recently and the rapid rise in interest has driven down the cost. With the advent of sub US1500 3D printers, this technology has moved out of the high-end marketplace and into the local office supply store. Schools across the US and elsewhere in the world are adding 3D printers to their technological workspaces and students have begun rapid-prototyping and manufacturing a variety of projects. This project attempted to streamline the process of transforming SRTM data from a GeoTIFF format by way of Python code. The resulting data was then inputted into a CAD-based program for

Support for Alzheimer's Caregivers: Psychometric Evaluation of Familial and Friend Support Measures

Science.gov (United States)

Wilks, Scott E.

2009-01-01

Objective: Information on the shortened, 20-item version of the Perceived Social Support Scale (S-PSSS) is scarce. The purpose of this study is to evaluate the psychometric properties of the S-PSSS Family (SSfa) and Friends (SSfr) subscales. Method: Because of their common coping method of social support, a cross-sectional sample of Alzheimer's…

A space-time lattice version of scalar electrodynamics

International Nuclear Information System (INIS)

Kijowski, J.; Thielmann, A.

1993-10-01

A Minkowski-lattice version of quantum scalar electrodynamics is constructed. Quantum field is consequently described in a gauge-independent way, i.e. the algebra of quantum observables of the theory is generated by gauge-invariant operators assigned to zero-, one-, and two-dimensional elements of the lattice. The operators satisfy canonical commutation relations. Field dynamics is formulated in terms of difference equations imposed on the field operators. The dynamics is obtained from a discrete version of the path-integral. (author). 19 refs

Iterative learning control with basis functions for media positioning in scanning inkjet printers

NARCIS (Netherlands)

Bolder, J.J.; Lemmen, B.P.; Koekebakker, S.H.; Oomen, T.A.E.; Bosgra, O.H.; Steinbuch, M.

2012-01-01

In printing systems, the positioning accuracy of the medium with respect to the print heads directly impacts print quality. In a regular document inkjet printer, the main task of the media positioning drive is to shift the medium after the printhead has finished a pass. Most media have the tendency

Development of x-y table for baby electron beam detection using dispose printer

International Nuclear Information System (INIS)

Leo Kwee Wah; Mohd Rizal Md Chulan; Muhamad Zahidee Taat; Abu Bakar Md Ghazali; Mohamad Nor Atan; Siti A'iasah Hashim

2005-01-01

This paper describes the development of X-Y table using the dispose printer. It consists the mechanical part and the control (Interfacing and software/programming) part description. As the result, the x-y table will be used to moves the electron beam detector for the baby electron beam machine. (Author)

The Integrated Tiger Series version 5.0

International Nuclear Information System (INIS)

Laub, Th.W.; Kensek, R.P.; Franke, B.C.; Lorence, L.J.; Crawford, M.J.; Quirk, Th.J.

2005-01-01

The Integrated Tiger Series (ITS) is a powerful and user-friendly software package permitting Monte Carlo solution of linear time-independent coupled electron/photon radiation transport problems, with or without the presence of macroscopic electric and magnetic fields of arbitrary spatial dependence. The package contains programs to perform 1-, 2-, and 3-dimensional simulations. Improvements in the ITS code package since the release of version 3.0 include improved physics, multigroup and adjoint capabilities, Computer-Aided Design geometry tracking, parallel implementations of all ITS codes, and more automated sub-zoning capabilities. These improvements and others are described as current or planned development efforts. The ITS package is currently at version 5.0. (authors)

A Novel Algorithm for Color Space Conversion Model from CMYK to LAB

OpenAIRE

Juan-li Hu; Jia-bing Deng; Shan-shan Zou

2010-01-01

Color space conversion has become a very important role in the image acquisition, display and the transmission of the color information in the replication. Printers and Image setter express color by CMYK space. But if color is edited and corrected in the CMYK space, it will cause a greater loss of color, and the Computing of computer will also be slowed down. So it often needs to be converted to a LAB uniform color space. Among the previous conversion methods, there is a widespread problem th...

Version control with Git

CERN Document Server

Loeliger, Jon

2012-01-01

Get up to speed on Git for tracking, branching, merging, and managing code revisions. Through a series of step-by-step tutorials, this practical guide takes you quickly from Git fundamentals to advanced techniques, and provides friendly yet rigorous advice for navigating the many functions of this open source version control system. This thoroughly revised edition also includes tips for manipulating trees, extended coverage of the reflog and stash, and a complete introduction to the GitHub repository. Git lets you manage code development in a virtually endless variety of ways, once you understand how to harness the system's flexibility. This book shows you how. Learn how to use Git for several real-world development scenarios ; Gain insight into Git's common-use cases, initial tasks, and basic functions ; Use the system for both centralized and distributed version control ; Learn how to manage merges, conflicts, patches, and diffs ; Apply advanced techniques such as rebasing, hooks, and ways to handle submodu...

Space Environment Information System (SPENVIS)

Science.gov (United States)

Kruglanski, Michel; de Donder, Erwin; Messios, Neophytos; Hetey, Laszlo; Calders, Stijn; Evans, Hugh; Daly, Eamonn

SPENVIS is an ESA operational software developed and maintained at BIRA-IASB since 1996. It provides standardized access to most of the recent models of the hazardous space environment, through a user-friendly Web interface (http://www.spenvis.oma.be/). The system allows spacecraft engineers to perform a rapid analysis of environmental problems related to natural radiation belts, solar energetic particles, cosmic rays, plasmas, gases, magnetic fields and micro-particles. Various reporting and graphical utilities and extensive help facilities are included to allow engineers with relatively little familiarity to produce reliable results. SPENVIS also contains an active, integrated version of the ECSS Space Environment Standard and access to in-flight data on the space environment. Although SPENVIS in the first place is designed to help spacecraft designers, it is also used by technical universities in their educational programs. In the framework of the ESA Space Situational Awareness Preparatory Programme, SPENVIS will be part of the initial set of precursor services of the Space Weather segment. SPENVIS includes several engineering models to assess to effects of the space environment on spacecrafts such as surface and internal charging, energy deposition, solar cell damage and SEU rates. The presentation will review how such models could be connected to in situ measurements or forecasting models of the space environment in order to produce post event analysis or in orbit effects alert. The last developments and models implemented in SPENVIS will also be presented.

Assessment of radionuclide databases in CAP88 mainframe version 1.0 and Windows-based version 3.0.

Science.gov (United States)

LaBone, Elizabeth D; Farfán, Eduardo B; Lee, Patricia L; Jannik, G Timothy; Donnelly, Elizabeth H; Foley, Trevor Q

2009-09-01

In this study the radionuclide databases for two versions of the Clean Air Act Assessment Package-1988 (CAP88) computer model were assessed in detail. CAP88 estimates radiation dose and the risk of health effects to human populations from radionuclide emissions to air. This program is used by several U.S. Department of Energy (DOE) facilities to comply with National Emission Standards for Hazardous Air Pollutants regulations. CAP88 Mainframe, referred to as version 1.0 on the U.S. Environmental Protection Agency Web site (http://www.epa.gov/radiation/assessment/CAP88/), was the very first CAP88 version released in 1988. Some DOE facilities including the Savannah River Site still employ this version (1.0) while others use the more user-friendly personal computer Windows-based version 3.0 released in December 2007. Version 1.0 uses the program RADRISK based on International Commission on Radiological Protection Publication 30 as its radionuclide database. Version 3.0 uses half-life, dose, and risk factor values based on Federal Guidance Report 13. Differences in these values could cause different results for the same input exposure data (same scenario), depending on which version of CAP88 is used. Consequently, the differences between the two versions are being assessed in detail at Savannah River National Laboratory. The version 1.0 and 3.0 database files contain 496 and 838 radionuclides, respectively, and though one would expect the newer version to include all the 496 radionuclides, 35 radionuclides are listed in version 1.0 that are not included in version 3.0. The majority of these has either extremely short or long half-lives or is no longer in production; however, some of the short-lived radionuclides might produce progeny of great interest at DOE sites. In addition, 122 radionuclides were found to have different half-lives in the two versions, with 21 over 3 percent different and 12 over 10 percent different.

Computer Simulation of Robotic Device Components in 3D Printer Manufacturing

Directory of Open Access Journals (Sweden)

M. A. Kiselev

2016-01-01

Full Text Available The paper considers a relevant problem "Computer simulation of robotic device components in manufacturing on a 3D printer" and highlights the problem of computer simulation based on the cognitive programming technology of robotic device components. The paper subject is urgent because computer simulation of force-torque and accuracy characteristics of robot components in terms of their manufacturing properties and conditions from polymeric and metallic materials is of paramount importance for programming and manufacturing on the 3D printers. Two types of additive manufacturing technologies were used:1. FDM (Fused deposition modeling - layered growth of products from molten plastic strands;2. SLM (Selective laser melting - selective laser sintering of metal powders, which, in turn, create:• conditions for reducing the use of expensive equipment;• reducing weight and increasing strength through optimization of  the lattice structures when using a bionic design;• a capability to implement mathematical modeling of individual components of robotic and other devices in terms of appropriate characteristics;• a 3D printing capability to create unique items, which cannot be made by other known methods.The paper aim was to confirm the possibility of ensuring the strength and accuracy characteristics of cases when printing from polymeric and metallic materials on a 3D printer. The investigation emphasis is on mathematical modeling based on the cognitive programming technology using the additive technologies in their studies since it is, generally, impossible to make the obtained optimized structures on the modern CNC machines.The latter allows us to create a program code to be clear to other developers without cost, additional time for development, adaptation and implementation.Year by year Russian companies increasingly use a 3D-print system in mechanical engineering, aerospace industry, and for scientific purposes. Machines for the additive

A low power consumption and multi-function mini-printer for the portable nuclear instruments

International Nuclear Information System (INIS)

Jin Yuheng; Zhang Jiahong

1994-01-01

The authors presents a method of fitting a commercial printing calculator to the low power consumption and multi-function mini-printer. It can be employed as a compact data recorder and simple data processing device attached to the portable nuclear instruments, which are powered by dry batteries

Low-Cost Printed Flexible Antenna by Using an Office Printer for Conformal Applications

Directory of Open Access Journals (Sweden)

Kashif Nisar Paracha

2018-01-01

Full Text Available A low-cost inkjet printing method for antenna fabrication on a polyethylene terephthalate (PET substrate is presented in this paper. An office inkjet printer is used to have desired patterns of silver nanoparticle ink on the PET substrate without any postprocessing. Silver nanoparticle ink cures instantly as soon as it is ejected from the printer on a chemically treated PET substrate. The thickness of the silver nanoparticle layer was measured to be 300 nm with a sheet resistance of as low as 0.3 Ω/sq and a conductivity around 1.11 × 107 S/m with single layer deposition. A coplanar waveguide- (CPW- fed Z-shape planar antenna on the PET substrate achieved the measured radiation efficiency of 62% and the IEEE gain of 1.44 dBi at 2.45 GHz. The printed antenna is also tested in bending conditions to ascertain its performance for the Internet of things (IoT conformal applications for the future 5G network.

Technology infusion of intellectual 3D printers-based prototyping of products into learning process

Science.gov (United States)

Boshhenko, T. V.; Chepur, P. V.

2018-03-01

The article considers the prospects for the technologies of intellectual design and prototyping applying 3D printers. It presents basic technologies of 3D printing, currently developed and released for construction. The experience of educational activities in the University to train students for the Academic Competitions on three-dimensional modeling and prototyping is described in the present article. Requirements for the prototyping implementation are given, allowing obtaining a positive effect from the technology infusion released for construction. The results of activities to train students for the Academic Competition are stated. It is established that the proposed approaches to the training of students have led to the highest score in the national contest in Novosibirsk when performing tasks for prototyping a stand for a cell phone and manufacturing the product on a 3D printer at the SLS technology, selective laser sintering. The conclusions about the possibilities and prospects of development of this direction in the industry in the entire country are drawn.

SpaceCube Core Software

Data.gov (United States)

National Aeronautics and Space Administration — Develop a flexible, modular and user friendly SpaceCube Core Software system that will dramatically simplify SpaceCube application development and enable any...

Airline network development in Europe and its implications for airport planning

NARCIS (Netherlands)

Burghouwt, G.

2007-01-01

Order by Fax Printer Friendly PDF Brochure Send to Friend Enquire before Buying Hard Copy Airline Network Development in Europe and its Implications for Airport Planning Ashgate Publishing, March 2007, Pages: 300 Description Table of Contents Enquire before Buying Send to a Friend The ongoing

Patient and family/friend satisfaction in a sample of Jordanian Critical Care Units.

Science.gov (United States)

Mosleh, S; Alja'afreh, M; Lee, A J

2015-12-01

The aim of the study was to assess the validity of family members/friends as proxies by comparing perceptions of satisfaction with care and decision making between critically ill patients and their family/friends. A comparative, descriptive cross-sectional study. Seven Critical Care Units across four public and military hospitals in the centre and southern regions of Jordan. A modified version of the Family Satisfaction-ICU (FS-ICU) questionnaire was distributed to Critical Care Unit (CCU) patients before hospital discharge. In addition, up to two family members/close friends were also asked to complete the questionnaire. A total of 213 patients (response rate 72%) and 246 family members/friends (response rate 79%) completed and returned the questionnaire. Although the majority of family members/friends and patients were satisfied with overall care, patients were generally significantly less satisfied (mean (SD) care subscale 75.6 (17.8) and 70.9 (17.3), respectively, (p=0.005). When individual items were examined, significant differences in nursing care (family/friends 80.1 (20.7) versus patient 75.9 (22.2), p=0.038) and inclusion in decision making (family/friends 53.9 (33.2) versus patient 62.0 (34.2), p=0.010) were found. The study showed a degree of congruence between patients and their family members/friends in relation to their satisfaction with the CCU experience. Thus, views of family/friends may serve as a proxy in assessing care and decision making processes of critically ill patients. Appropriate training of the critical care team and provision of strategies to address the concerns of patients' families are needed to improve overall patient satisfaction. Copyright © 2015 Elsevier Ltd. All rights reserved.

Dataset on energy efficiency assessment and measurement method for child-friendly space in cold residential area

Directory of Open Access Journals (Sweden)

Kai Ren

2017-10-01

Full Text Available The data related in this paper are related to “Environmental-behavior studies of sustainable construction of the third place – based on outdoor environment-behavior cross-feed symbiotic analysis and verification of selective activities” (Ren, 2017 [1]. The dataset was from a field sub-time extended investigation to children of Hohhot West Inner Mongolia Electric Power Community Residential Area in Inner Mongolia of China that belongs to cold region of ID area according to Chinese design code for buildings. This filed data provided descriptive statistics about outdoor time, behavior scale specificity, age exclusivity and self-centeredness for children in different ages (babies, preschool children, school age children. This data provided five measurement elements of child-friendly space and their weight ratio. The field data set is made publicly available to enable critical or extended analyzes.

Characterization of hydrogel printer for direct cell-laden scaffolds

Science.gov (United States)

Whulanza, Yudan; Arsyan, Rendria; Saragih, Agung Shamsuddin

2018-02-01

The additive manufacturing technology has been massively developed since the last decade. The technology was previously known as rapid prototyping techniques that aimed to produce a prototyping product in fast and economical way. Currently, this technique is also applied to fabricate microstructure utilized in tissue engineering technology. Here, we introduce a 3D printer which using hydrogel gelatin to realize cell laden scaffold with dimension around 50-100 µm. However, in order to fabricate such a precise dimension, an optimum working parameters are required to control the physical properties of gelatin. At the end of our study, we formulated the best parameters to perform the product as we desired.

In-Space Manufacturing Baseline Property Development

Science.gov (United States)

Stockman, Tom; Schneider, Judith; Prater, Tracie; Bean, Quincy; Werkheiser, Nicki

2016-01-01

The In-Space Manufacturing (ISM) project at NASA Marshall Space Flight Center currently operates a 3D FDM (fused deposition modeling) printer onboard the International Space Station. In order to enable utilization of this capability by designer, the project needs to establish characteristic material properties for materials produced using the process. This is difficult for additive manufacturing since standards and specifications do not yet exist for these technologies. Due to availability of crew time, there are limitations to the sample size which in turn limits the application of the traditional design allowables approaches to develop a materials property database for designers. In this study, various approaches to development of material databases were evaluated for use by designers of space systems who wish to leverage in-space manufacturing capabilities. This study focuses on alternative statistical techniques for baseline property development to support in-space manufacturing.

Intermediate peer contexts and educational outcomes: Do the friends of students' friends matter?

Science.gov (United States)

Carbonaro, William; Workman, Joseph

2016-07-01

Sociologists of education have long been interested in the effects of peer relations on educational outcomes. Recent theory and research on adolescence suggest that peers on the boundaries of students' friendship networks may play an important role in shaping behaviors and educational outcomes. In this study, we examine the importance of a key "intermediate peer context" for students' outcomes: the friends of a student's friends. Our findings indicate both friends' and friends' friends' characteristics independently predict students' college expectations and their risk of dropping out of high school (although only friends' characteristics predict GPA). Our models suggest the magnitude of students' friends-of-friends' characteristics are at least as large their friends' characteristics. Together, the association between the peer context and students outcomes is considerably larger when accounting for both the characteristics of students' friends and the friends of their friends. Copyright © 2016 Elsevier Inc. All rights reserved.

‘Aber mein Lieber Schneider’: The Printer as a Media Actor and the Drama of Production in Then Swänska Argus (1732–34

Directory of Open Access Journals (Sweden)

Tilda Maria Forselius

2016-07-01

Full Text Available Then Swänska Argus, a weekly journal in the Spectator pattern, was published in Stockholm between 1732 and 1734. Whereas the editor and author Olof Dalin (1708–63 has gained much fame for the enterprise, not much is known about the printer Benjamin Gottlieb Schneider (16??–1738. In this essay I focus on the available evidence about the printer and printing conditions, as well as on the fact that several essays and shorter segments in Then Swänska Argus are addressed to the printer or deal with printing issues. My thesis is that this content played a part in the identity formation of the medium, as it stands for the editor’s interest in the printer and related technology at a time when the moral weekly was new in Sweden. By displaying the making of the medium and the difficulties around it, these passages enable readers to witness the drama of production where the printer plays a leading role. Furthermore, as the narrator Argus is addressing the readers directly and pleading with them to be loyal followers in spite of the printing errors or other potential problems, Argus is also making them actively aware of their part in this drama. In so doing, an education of the readership in questions pertaining to the production process is taking place.

Concurrent validity of the Swedish version of the life-space assessment questionnaire

Directory of Open Access Journals (Sweden)

Sofi Fristedt

2016-11-01

Full Text Available Abstract Background The Life-Space Assessment (LSA, developed in the USA, is an instrument focusing on mobility with respect to reaching different areas defined as life-spaces, extending from the room where the person sleeps to mobility outside one’s hometown. A newly translated Swedish version of the LSA (LSA-S has been tested for test-retest reliability, but the validity remains to be tested. The purpose of the present study was to examine the concurrent validity of the LSA-S, by comparing and correlating the LSA scores to other measures of mobility. Method The LSA was included in a population-based study of health, functioning and mobility among older persons in Sweden, and the present analysis comprised 312 community-dwelling participants. To test the concurrent validity, the LSA scores were compared to a number of other mobility-related variables, including the Short Physical Performance Battery (SPPB as well as “stair climbing”, “transfers”, “transportation”, “food shopping”, “travel for pleasure” and “community activities”. The LSA total mean scores for different levels of the other mobility-related variables, and measures of correlation were calculated. Results Higher LSA total mean scores were observed with higher levels of all the other mobility related variables. Most of the correlations between the LSA and the other mobility variables were large (r = 0.5–1.0 and significant at the 0.01 level. The LSA total score, as well as independent life-space and assistive life-space correlated with transportation (0.63, 0.66, 0.64 and food shopping (0.55, 0.58, 0.55. Assistive life-space also correlated with SPPB (0.47. With respect to maximal life-space, the correlations with the mobility-related variables were generally lower (below 0.5, probably since this aspect of life-space mobility is highly influenced by social support and is not so dependent on the individual’s own physical function. Conclusion LSA was

Romantic Partners, Friends, Friends with Benefits, and Casual Acquaintances As Sexual Partners

Science.gov (United States)

Furman, Wyndol; Shaffer, Laura

2011-01-01

The purpose of the present study was to provide a detailed examination of sexual behavior with different types of partners. A sample of 163 young adults reported on their light nongenital, heavy nongenital, and genital sexual activity with romantic partners, friends, and casual acquaintances. They described their sexual activity with “friends with benefits” as well as with friends in general. Young adults were most likely to engage in sexual behavior with romantic partners, but sexual behavior also often occurred with some type of nonromantic partner. More young adults engaged in some form of sexual behavior with casual acquaintances than with friends with benefits. The frequencies of sexual behavior, however, were greater with friends with benefits than with friends or casual acquaintances. Interview and questionnaire data revealed that friends with benefits were typically friends, but not necessarily. Nonsexual activities were also less common with friends with benefits than other friends. Taken together, the findings illustrate the value of differentiating among different types of nonromantic partners and different levels of sexual behavior. PMID:21128155

Development of environmentally friendly universal controller. Data and materials; 1998 nendo kankyo taio universal controller no kaihatsu seika hokokusho. Shiryohen

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

Research and development was carried out for an 'environmentally friendly universal controller (UC)' which would be 'user-friendly and energy-saving' when used with electrical home appliances, and data and materials on them were compiled into this volume. It covers the specifications (Versions 0.6 and 0.51) of a newly developed two-way controller protocol, the specification (Version 0.1) of two-way remote control IrDA-C communication unit hardware, an infrared communication protocol IrDa Control, and the like. It also accommodates information collected through surveys of technological trends as reflected in technical literature, Internet home pages, catalogs, and the like, concerning the user-friendliness of electrical home appliances, remote control, domestic consumption of electric power, and the like. Also covered is the result of surveys of patents involving environmentally friendly UC related technologies, namely, Japanese patents (from applications made in 1979 through disclosures made in 1998) and U.S. patents (registrations made in 1982 and thereafter). Furthermore, it contains the result of surveys of actualities of domestic use conducted for the purpose of clarifying the effect of environmentally friendly UC introduction, how such UCs are being accepted by the public, and the conditions that should be satisfied for their popularization. (NEDO)

Development of environmentally friendly universal controller. Data and materials; 1998 nendo kankyo taio universal controller no kaihatsu seika hokokusho. Shiryohen

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

Research and development was carried out for an 'environmentally friendly universal controller (UC)' which would be 'user-friendly and energy-saving' when used with electrical home appliances, and data and materials on them were compiled into this volume. It covers the specifications (Versions 0.6 and 0.51) of a newly developed two-way controller protocol, the specification (Version 0.1) of two-way remote control IrDA-C communication unit hardware, an infrared communication protocol IrDa Control, and the like. It also accommodates information collected through surveys of technological trends as reflected in technical literature, Internet home pages, catalogs, and the like, concerning the user-friendliness of electrical home appliances, remote control, domestic consumption of electric power, and the like. Also covered is the result of surveys of patents involving environmentally friendly UC related technologies, namely, Japanese patents (from applications made in 1979 through disclosures made in 1998) and U.S. patents (registrations made in 1982 and thereafter). Furthermore, it contains the result of surveys of actualities of domestic use conducted for the purpose of clarifying the effect of environmentally friendly UC introduction, how such UCs are being accepted by the public, and the conditions that should be satisfied for their popularization. (NEDO)

3D printing of MRI compatible components: why every MRI research group should have a low-budget 3D printer.

Science.gov (United States)

Herrmann, Karl-Heinz; Gärtner, Clemens; Güllmar, Daniel; Krämer, Martin; Reichenbach, Jürgen R

2014-10-01

To evaluate low budget 3D printing technology to create MRI compatible components. A 3D printer is used to create customized MRI compatible components, a loop-coil platform and a multipart mouse fixation. The mouse fixation is custom fit for a dedicated coil and facilitates head fixation with bite bar, anesthetic gas supply and biomonitoring sensors. The mouse fixation was tested in a clinical 3T scanner. All parts were successfully printed and proved MR compatible. Both design and printing were accomplished within a few days and the final print results were functional with well defined details and accurate dimensions (Δ3D printer can be used to quickly progress from a concept to a functional device at very low production cost. While 3D printing technology does impose some restrictions on model geometry, additive printing technology can create objects with complex internal structures that can otherwise not be created by using lathe technology. Thus, we consider a 3D printer a valuable asset for MRI research groups. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.

Integrated Voltage—Current Monitoring and Control of Gas Metal Arc Weld Magnetic Ball-Jointed Open Source 3-D Printer

Directory of Open Access Journals (Sweden)

Yuenyong Nilsiam

2015-11-01

Full Text Available To provide process optimization of metal fabricating self-replicating rapid prototyper (RepRap 3-D printers requires a low-cost sensor and data logger system to measure current (I and voltage (V of the gas metal arc welders (GMAW. This paper builds on previous open-source hardware development to provide a real-time measurement of welder I-V where the measuring circuit is connected to two analog inputs of the Arduino that is used to control the 3-D printer itself. Franklin firmware accessed through a web interface that is used to control the printer allows storing the measured values and downloading those stored readings to the user’s computer. To test this custom current and voltage monitoring device this study reports on its use on an upgraded all metal RepRap during the printing of aluminum alloy (ER1100, ER4043, ER4943, ER4047, and ER5356. The voltage and current data were analyzed on a per alloy basis and also layer-by-layer in order to evaluate the device’s efficacy as a monitoring device for 3-D printing and the results of the integrated design are discussed.

A simulator for training in endovascular aneurysm repair: The use of three dimensional printers.

Science.gov (United States)

Torres, I O; De Luccia, N

2017-08-01

To develop an endovascular aneurysm repair (EVAR) simulation system using three dimensional (3D) printed aneurysms, and to evaluate the impact of patient specific training prior to EVAR on the surgical performance of vascular surgery residents in a university hospital in Brazil. This was a prospective, controlled, single centre study. During 2015, the aneurysms of patients undergoing elective EVAR at São Paulo University Medical School were 3D printed and used in training sessions with vascular surgery residents. The 3D printers Stratasys-Connex 350, Formlabs-Form1+, and Makerbot were tested. Ten residents were enrolled in the control group (five residents and 30 patients in 2014) or the training group (five residents and 25 patients in 2015). The control group performed the surgery under the supervision of a senior vascular surgeon (routine procedure, without simulator training). The training group practised the surgery in a patient specific simulator prior to the routine procedure. Objective parameters were analysed, and a subjective questionnaire addressing training utility and realism was answered. Patient specific training reduced fluoroscopy time by 30% (mean 48 min, 95% confidence interval [CI] 40-58 vs. 33 min, 95% CI 26-42 [p training useful and realistic, and reported that it increased their self confidence. The 3D printers Form1+ (using flexible resin) and Makerbot (using silicone) provided the best performance based on simulator quality and cost. An EVAR simulation system using 3D printed aneurysms was feasible. The best results were obtained with the 3D printers Form1+ (using flexible resin) and Makerbot (using silicone). Patient specific training prior to EVAR at a university hospital in Brazil improved residents' surgical performance (based on fluoroscopy time, surgery time, and volume of contrast used) and increased their self confidence. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

[Occupational cholangiocarcinoma in a printer that responded to neoadjuvant chemoradiotherapy].

Science.gov (United States)

Nakagawa, Kei; Katayose, Yu; Ishida, Kazuyuki; Hayashi, Hiroki; Morikawa, Takanori; Yoshida, Hiroshi; Motoi, Fuyuhiko; Naitoh, Takeshi; Kubo, Shoji; Unno, Michiaki

2015-07-01

A 42-year-old man working at a printing company was referred to our hospital for examination and treatment of icterus. We diagnosed resectable hilar cholangiocarcinoma and provided neoadjuvant chemoradiotherapy, extended right hepatectomy, and extrahepatic bile duct resection. A detailed history revealed that he had used 1,2-dichloropropane as part of his work as an offset colour proof-printer, and he has subsequently been recognized as having occupational cholangiocarcinoma. He has survived without recurrence for more than 2 and half years since the liver resection. In the present report, we describe our valuable experience of neoadjuvant chemoradiotherapy for occupational cholangiocarcinoma.

A user-friendly means to scale from the biochemistry of photosynthesis to whole crop canopies and production in time and space - development of Java WIMOVAC.

Science.gov (United States)

Song, Qingfeng; Chen, Dairui; Long, Stephen P; Zhu, Xin-Guang

2017-01-01

Windows Intuitive Model of Vegetation response to Atmosphere and Climate Change (WIMOVAC) has been used widely as a generic modular mechanistically rich model of plant production. It can predict the responses of leaf and canopy carbon balance, as well as production in different environmental conditions, in particular those relevant to global change. Here, we introduce an open source Java user-friendly version of WIMOVAC. This software is platform independent and can be easily downloaded to a laptop and used without any prior programming skills. In this article, we describe the structure, equations and user guide and illustrate some potential applications of WIMOVAC. © 2016 The Authors Plant, Cell & Environment Published by John Wiley & Sons Ltd.

Design and Analysis of Fused Deposition Modeling 3D Printer Nozzle for Color Mixing

Directory of Open Access Journals (Sweden)

Shanling Han

2017-01-01

Full Text Available Fused deposition modeling (FDM has been one of the most widely used rapid prototyping (RP technologies leading to the increase in market attention. Obviously it is desirable to print 3D objects; however, existing FDM printers are restricted to printing only monochrome objects because of the entry-level nozzle structure, and literature on the topic is also sparse. In this paper, the CAD model of the nozzle is established first by UG (Unigraphics NX software to show the structure of fused deposition modeling 3D printer nozzle for color mixing. Second, the flow channel model of the nozzle is extracted and simplified. Then, the CAD and finite element model are established by UG and ICEM CFD software, respectively, to prepare for the simulation. The flow field is simulated by Fluent software. The nozzle’s suitable temperature at different extrusion speeds is obtained, and the reason for the blockage at the intersection of the heating block is revealed. Finally, test verification of the nozzle is performed, which can produce mixed-color artifacts stably.

A feasibility study for using ABS plastic and a low-cost 3D printer for patient-specific brachytherapy mould design.

Science.gov (United States)

Harris, Benjamin D; Nilsson, Sanna; Poole, Christopher M

2015-09-01

This feasibility study aims to determine if a low-cost 3D printer (BitsFromBytes 3D Touch) with ABS plastic can print custom mould structures and catheter channels defined in a brachytherapy treatment planning system (Nucletron Oncentra) for patient-specific treatment. Printer accuracy was evaluated through physical measurement, and print quality was investigated by adjusting print parameters (print speed, layer thickness, percentage infill). Catheter positioning and reproducibility were measured over repeated insertions. ABS plastic water equivalency was investigated by comparing Ir-192 HDR source dose distributions, measured with radiochromic film, in ABS plastic and in water. Structures and catheter channels were printed accurately to within 0.5 mm laterally and 1 mm in the vertical print direction. Adjusting print parameters could reduce print time, albeit with reduced print quality. 3.5 mm channel diameters allowed for easy catheter insertion. Catheter positioning was reproducible to within 0.5 mm but, because of catheter flex within the channel, was on average 1 mm offset from defined TPS positions. This offset could be accounted for by repeating the treatment planning CT scan with the printed mould positioned on the patient. Dose attenuation in ABS plastic and in water was equivalent to within the measurement limitations. While clinical uses for this particular low-cost printer and ABS plastic are limited by print size restrictions and non-certification for biocompatibility, it has been demonstrated that a low-cost 3D printer set-up can accurately create custom moulds and catheter channels potentially acceptable for clinical use.

Deposition of PEDOT: PSS Nanoparticles as a Conductive Microlayer Anode in OLEDs Device by Desktop Inkjet Printer

Directory of Open Access Journals (Sweden)

S. Ummartyotin

2011-01-01

Full Text Available A simple microfabrication technique for delivering macromolecules and patterning microelectrode arrays using desktop inkjet printer was described. Aqueous solution of nanoparticle of poly (3,4-ethylenedioxythiophene (PEDOT doped with polystyrene sulfonic acid (PSS was prepared while its particle size, the surface tension, and the viscosity of the solution were adjusted to be suitable for deposition on a flexible cellulose nanocomposite substrate via inkjet printer. The statistical average of PEDOT: PSS particle size of 100 nm was observed. The microthickness, surface morphology, and electrical conductivity of the printed substrate were then characterized by profilometer, atomic force microscope (AFM, and four-point probe electrical measurement, respectively. The inkjet deposition of PEDOT: PSS was successfully carried out, whilst retained its transparency feature. Highly smooth surface (roughness ~23–44 nm was achieved.

3D Systems” ‘Stuck in the Middle’ of the 3D Printer Boom?

NARCIS (Netherlands)

A. Hoffmann (Alan)

2014-01-01

textabstract3D Systems, the pioneer of 3D printing, predicted a future where "kids from 8 to 80" could design and print their ideas at home. By 2013, 9 years after the creation of the first working 3D printer, there were more than 30 major 3D printing companies competing for market share. 3DS and

Modeling Age-Friendly Environment, Active Aging, and Social Connectedness in an Emerging Asian Economy

Directory of Open Access Journals (Sweden)

Ming-Ming Lai

2016-01-01

Full Text Available This paper empirically tested eight key features of WHO guidelines to age-friendly community by surveying 211 informal caregivers and 402 self-care adults (aged 45 to 85 and above in Malaysia. We examined the associations of these eight features with active aging and social connectedness through exploratory and confirmatory factor analyses. A structural model with satisfactory goodness-of-fit indices (CMIN/df = 1.11, RMSEA = 0.02, NFI = 0.97, TLI = 1.00, CFI = 1.00, and GFI = 0.96 indicates that transportation and housing, community support and health services, and outdoor spaces and buildings are statistically significant in creating an age-friendly environment. We found a statistically significant positive relationship between an age-friendly environment and active aging. This relationship is mediated by social connectedness. The results indicate that built environments such as accessible public transportations and housing, affordable and accessible healthcare services, and elderly friendly outdoor spaces and buildings have to be put into place before social environment in building an age-friendly environment. Otherwise, the structural barriers would hinder social interactions for the aged. The removal of the environmental barriers and improved public transportation services provide short-term solutions to meet the varied and growing needs of the older population.

Filament Advance Detection Sensor for Fused Deposition Modelling 3D Printers.

Science.gov (United States)

Soriano Heras, Enrique; Blaya Haro, Fernando; de Agustín Del Burgo, José M; Islán Marcos, Manuel; D'Amato, Roberto

2018-05-09

The main purpose of this paper is to present a system to detect extrusion failures in fused deposition modelling (FDM) 3D printers by sensing that the filament is moving forward properly. After several years using these kind of machines, authors detected that there is not any system to detect the main problem in FDM machines. Authors thought in different sensors and used the weighted objectives method, one of the most common evaluation methods, for comparing design concepts based on an overall value per design concept. Taking into account the obtained scores of each specification, the best choice for this work is the optical encoder. Once the sensor is chosen, it is necessary to design de part where it will be installed without interfering with the normal function of the machine. To do it, photogrammetry scanning methodology was employed. The developed device perfectly detects the advance of the filament without affecting the normal operation of the machine. Also, it is achieved the primary objective of the system, avoiding loss of material, energy, and mechanical wear, keeping the premise of making a low-cost product that does not significantly increase the cost of the machine. This development has made it possible to use the printer with remains of coil filaments, which were not spent because they were not sufficient to complete an impression. Also, printing models in two colours with only one extruder has been enabled by this development.

Filament Advance Detection Sensor for Fused Deposition Modelling 3D Printers

Directory of Open Access Journals (Sweden)

Enrique Soriano Heras

2018-05-01

Full Text Available The main purpose of this paper is to present a system to detect extrusion failures in fused deposition modelling (FDM 3D printers by sensing that the filament is moving forward properly. After several years using these kind of machines, authors detected that there is not any system to detect the main problem in FDM machines. Authors thought in different sensors and used the weighted objectives method, one of the most common evaluation methods, for comparing design concepts based on an overall value per design concept. Taking into account the obtained scores of each specification, the best choice for this work is the optical encoder. Once the sensor is chosen, it is necessary to design de part where it will be installed without interfering with the normal function of the machine. To do it, photogrammetry scanning methodology was employed. The developed device perfectly detects the advance of the filament without affecting the normal operation of the machine. Also, it is achieved the primary objective of the system, avoiding loss of material, energy, and mechanical wear, keeping the premise of making a low-cost product that does not significantly increase the cost of the machine. This development has made it possible to use the printer with remains of coil filaments, which were not spent because they were not sufficient to complete an impression. Also, printing models in two colours with only one extruder has been enabled by this development.

Flavivirus and Filovirus EvoPrinters: New alignment tools for the comparative analysis of viral evolution.

Directory of Open Access Journals (Sweden)

Thomas Brody

2017-06-01

Full Text Available Flavivirus and Filovirus infections are serious epidemic threats to human populations. Multi-genome comparative analysis of these evolving pathogens affords a view of their essential, conserved sequence elements as well as progressive evolutionary changes. While phylogenetic analysis has yielded important insights, the growing number of available genomic sequences makes comparisons between hundreds of viral strains challenging. We report here a new approach for the comparative analysis of these hemorrhagic fever viruses that can superimpose an unlimited number of one-on-one alignments to identify important features within genomes of interest.We have adapted EvoPrinter alignment algorithms for the rapid comparative analysis of Flavivirus or Filovirus sequences including Zika and Ebola strains. The user can input a full genome or partial viral sequence and then view either individual comparisons or generate color-coded readouts that superimpose hundreds of one-on-one alignments to identify unique or shared identity SNPs that reveal ancestral relationships between strains. The user can also opt to select a database genome in order to access a library of pre-aligned genomes of either 1,094 Flaviviruses or 460 Filoviruses for rapid comparative analysis with all database entries or a select subset. Using EvoPrinter search and alignment programs, we show the following: 1 superimposing alignment data from many related strains identifies lineage identity SNPs, which enable the assessment of sublineage complexity within viral outbreaks; 2 whole-genome SNP profile screens uncover novel Dengue2 and Zika recombinant strains and their parental lineages; 3 differential SNP profiling identifies host cell A-to-I hyper-editing within Ebola and Marburg viruses, and 4 hundreds of superimposed one-on-one Ebola genome alignments highlight ultra-conserved regulatory sequences, invariant amino acid codons and evolutionarily variable protein-encoding domains within a

friendly clinic on retention of HIV-infected children in care

African Journals Online (AJOL)

2017-08-22

Aug 22, 2017 ... space where a child feels both physically and emotion- ally secure and at ... experience, retention in care and loss to follow up of. HIV-infected children. ... The clinic area was painted with artistic drawings in child-friendly ...

Consumer exposures to laser printer-emitted engineered nanoparticles: A case study of life-cycle implications from nano-enabled products.

Science.gov (United States)

Pirela, Sandra V; Sotiriou, Georgios A; Bello, Dhimiter; Shafer, Martin; Bunker, Kristin Lee; Castranova, Vincent; Thomas, Treye; Demokritou, Philip

2015-01-01

It is well established that printers emit nanoparticles during their operation. To-date, however, the physicochemical and toxicological characterization of "real world" printer-emitted nanoparticles (PEPs) remains incomplete, hampering proper risk assessment efforts. Here, we investigate our earlier hypothesis that engineered nanomaterials (ENMs) are used in toners and ENMs are released during printing (consumer use). Furthermore, we conduct a detailed physicochemical and morphological characterization of PEPs in support of ongoing toxicological assessment. A comprehensive suite of state of the art analytical methods and tools was employed for the physicochemical and morphological characterization of 11 toners widely utilized in printers from major printer manufacturers and their PEPs. We confirmed that a number of ENMs incorporated into toner formulations (e.g. silica, alumina, titania, iron oxide, zinc oxide, copper oxide, cerium oxide, carbon black among others) and released into the air during printing. All evaluated toners contained large amounts of organic carbon (OC, 42-89%), metals/metal oxides (1-33%), and some elemental carbon (EC, 0.33-12%). The PEPs possess a composition similar to that of toner and contained 50-90% OC, 0.001-0.5% EC and 1-3% metals. While the chemistry of the PEPs generally reflected that of their toners, considerable differences are documented indicative of potential transformations taking place during consumer use (printing). We conclude that: (i) Routine incorporation of ENMs in toners classifies them as nano-enabled products (NEPs); (ii) These ENMs become airborne during printing; (iii) The chemistry of PEPs is complex and it reflects that of the toner and paper. This work highlights the importance of understanding life-cycle (LC) nano-EHS implications of NEPs and assessing real world exposures and associated toxicological properties rather than focusing on "raw" materials used in the synthesis of an NEP.

Data path design and image quality aspects of the next generation multifunctional printer

Science.gov (United States)

Brassé, M. H. H.; de Smet, S. P. R. C.

2008-01-01

Multifunctional devices (MFDs) are increasingly used as a document hub. The MFD is used as a copier, scanner, printer, and it facilitates digital document distribution and sharing. This imposes new requirements on the design of the data path and its image processing. Various design aspects need to be taken into account, including system performance, features, image quality, and cost price. A good balance is required in order to develop a competitive MFD. A modular datapath architecture is presented that supports all the envisaged use cases. Besides copying, colour scanning is becoming an important use case of a modern MFD. The copy-path use case is described and it is shown how colour scanning can also be supported with a minimal adaptation to the architecture. The key idea is to convert the scanner data to an opponent colour space representation at the beginning of the image processing pipeline. The sub-sampling of chromatic information allows for the saving of scarce hardware resources without significant perceptual loss of quality. In particular, we have shown that functional FPGA modules from the copy application can also be used for the scan-to-file application. This makes the presented approach very cost-effective while complying with market conform image quality standards.

Phil Friend julgustab riske võtma / Phil Friend ; interv. Harda Roosna

Index Scriptorium Estoniae

Friend, Phil

2003-01-01

Suurbritannia koolitus- ja konsultatsioonifirma Churchill & Friend juhataja Phil Friend vastab küsimustele oma firma missiooni kohta Hiiumaal, puuetega inimeste elu erinevuste kohta Hiiumaal ja Suurbritannias. Vt. samas: Phil Friend julgustas tööandjaid puuetega inimesi tööle võtma

Development of EASYQAD version β: A Visualization Code System for QAD-CGGP-A Gamma and Neutron Shielding Calculation Code

International Nuclear Information System (INIS)

Kim, Jae Cheon; Lee, Hwan Soo; Ha, Pham Nhu Viet; Kim, Soon Young; Shin, Chang Ho; Kim, Jong Kyung

2007-01-01

EASYQAD had been previously developed by using MATLAB GUI (Graphical User Interface) in order to perform conveniently gamma and neutron shielding calculations at Hanyang University. It had been completed as version α of radiation shielding analysis code. In this study, EASYQAD was upgraded to version β with many additional functions and more user-friendly graphical interfaces. For general users to run it on Windows XP environment without any MATLAB installation, this version was developed into a standalone code system

SM-1420 computer conjugation with the ES-5017 magnetic tape storage device and the SM-6313 printer

International Nuclear Information System (INIS)

Zhurkin, V.V.; Safonov, A.A.; Troitskij, A.N.

1987-01-01

The flow sheets are given and the methods of the technical implementation of expansion units of SM 5002.4 controllers to connect NML ES-5017 and analogue-digital printer ATsPU SM-6818, respectively, to SM-1420 computer are described

Gridded Species Distribution, Version 1: Global Amphibians Presence Grids

Data.gov (United States)

National Aeronautics and Space Administration — The Global Amphibians Presence Grids of the Gridded Species Distribution, Version 1 is a reclassified version of the original grids of amphibian species distribution...

A kernel version of spatial factor analysis

DEFF Research Database (Denmark)

Nielsen, Allan Aasbjerg

2009-01-01

. Schölkopf et al. introduce kernel PCA. Shawe-Taylor and Cristianini is an excellent reference for kernel methods in general. Bishop and Press et al. describe kernel methods among many other subjects. Nielsen and Canty use kernel PCA to detect change in univariate airborne digital camera images. The kernel...... version of PCA handles nonlinearities by implicitly transforming data into high (even infinite) dimensional feature space via the kernel function and then performing a linear analysis in that space. In this paper we shall apply kernel versions of PCA, maximum autocorrelation factor (MAF) analysis...

Space Van system update

Science.gov (United States)

Cormier, Len

1992-07-01

The Space Van is a proposed commercial launch vehicle that is designed to carry 1150 kg to a space-station orbit for a price of $1,900,000 per flight in 1992 dollars. This price includes return on preoperational investment. Recurring costs are expected to be about $840,000 per flight. The Space Van is a fully reusable, assisted-single-stage-to orbit system. The most innovative new feature of the Space Van system is the assist-stage concept. The assist stage uses only airbreathing engines for vertical takeoff and vertical landing in the horizontal attitude and for launching the rocket-powered orbiter stage at mach 0.8 and an altitude of about 12 km. The primary version of the orbiter is designed for cargo-only without a crew. However, a passenger version of the Space Van should be able to carry a crew of two plus six passengers to a space-station orbit. Since the Space Van is nearly single-stage, performance to polar orbit drops off significantly. The cargo version should be capable of carrying 350 kg to a 400-km polar orbit. In the passenger version, the Space Van should be able to carry two crew members - or one crew member plus a passenger.

N -Ink Printer Characterization With Barycentric Subdivision.

Science.gov (United States)

Babaei, Vahid; Hersch, Roger D

2016-07-01

Printing with a large number of inks, also called N -ink printing, is a challenging task. The challenges comprise spectral modeling of the printer, color separation, halftoning, and limitations of the amount of inks. Juxtaposed halftoning, a perfectly dot-off-dot halftoning method, has proved to be useful to address some of these challenges. However, for juxtaposed halftones, prediction of colors as a function of ink area coverages has not yet been fully investigated. The goal of this paper is to introduce a spectral prediction model for N -ink juxtaposed-halftone prints. As the area-coverage domain of juxtaposed inks forms a simplex, we propose a cellular subdivision of the area-coverage domain using the barycentric subdivision of simplexes. The barycentric subdivision provides algorithmically straightforward means to design and implement an N -ink color prediction model. Within the subdomain cells, the Yule-Nielsen spectral Neugebauer model is used for the spectral prediction. Our proposed model is highly accurate for prints with a large number of inks while requiring a relatively low number of calibration samples.

Delayed manifestations of CNS effects in formerly exposed printers - A 20-year follow-up

OpenAIRE

Nilson, Linda Nordling; Karlson, Björn; Nise, Gun; Malmberg, Birgitta; Örbaek, Palle

2010-01-01

Whether long-term occupational exposure to organic solvents may affect mental and cognitive functioning later in life, remains unclear. In this study, twelve rotogravure printers formerly exposed to toluene and 19 referents, all initially examined in the mid-1980s, were reexamined after twenty years, applying neuropsychological tests, symptoms and social interaction questionnaires, medical examination, and exposure assessment of each individual's cumulative exposure. By far the most exten...

A re-entrant flowshop heuristic for online scheduling of the paper path in a large scale printer

NARCIS (Netherlands)

Waqas, U.; Geilen, M.C.W.; Kandelaars, J.; Somers, L.J.A.M.; Basten, T.; Stuijk, S.; Vestjens, P.G.H.; Corporaal, H.

2015-01-01

A Large Scale Printer (LSP) is a Cyber Physical System (CPS) printing thousands of sheets per day with high quality. The print requests arrive at run-time requiring online scheduling. We capture the LSP scheduling problem as online scheduling of re-entrant flowshops with sequence dependent setup

Young friendship in HFASD and typical development: friend versus non-friend comparisons.

Science.gov (United States)

Bauminger-Zviely, Nirit; Agam-Ben-Artzi, Galit

2014-07-01

This study conducted comparative assessment of friendship in preschoolers with high-functioning autism spectrum disorder (HFASD, n = 29) versus preschoolers with typical development (n = 30), focusing on interactions with friends versus acquaintances. Groups were matched on SES, verbal/nonverbal MA, IQ, and CA. Multidimensional assessments included: mothers' and teachers' reports about friends' and friendship characteristics and observed individual and dyadic behaviors throughout interactions with friends versus non-friends during construction, drawing, and free-play situations. Findings revealed group differences in peer interaction favoring the typical development group, thus supporting the neuropsychological profile of HFASD. However, both groups' interactions with friends surpassed interactions with acquaintances on several key socio-communicative and intersubjective capabilities, thus suggesting that friendship may contribute to enhancement and practice of social interaction in HFASD.

Integrated Reliability and Risk Analysis System (IRRAS), Version 2.5: Reference manual

International Nuclear Information System (INIS)

Russell, K.D.; McKay, M.K.; Sattison, M.B.; Skinner, N.L.; Wood, S.T.; Rasmuson, D.M.

1991-03-01

The Integrated Reliability and Risk Analysis System (IRRAS) is a state-of-the-art, microcomputer-based probabilistic risk assessment (PRA) model development and analysis tool to address key nuclear plant safety issues. IRRAS is an integrated software tool that gives the user the ability to create and analyze fault trees and accident sequences using a microcomputer. This program provides functions that range from graphical fault tree construction to cut set generation and quantification. Version 1.0 of the IRRAS program was released in February of 1987. Since that time, many user comments and enhancements have been incorporated into the program providing a much more powerful and user-friendly system. This version has been designated IRRAS 2.5 and is the subject of this Reference Manual. Version 2.5 of IRRAS provides the same capabilities as Version 1.0 and adds a relational data base facility for managing the data, improved functionality, and improved algorithm performance. 7 refs., 348 figs

Intercomparison of ILAS-II version 1.4 and version 2 target parameters with MIPAS-Envisat measurements

Directory of Open Access Journals (Sweden)

A. Griesfeller

2008-02-01

Full Text Available This paper assesses the mean differences between the two ILAS-II data versions (1.4 and 2 by comparing them with MIPAS measurements made between May and October 2003. For comparison with ILAS-II results, MIPAS data processed at the Institut für Meteorologie und Klimaforschung, Karlsruhe, Germany (IMK in cooperation with the Instituto de Astrofísica de Andalucía (IAA in Granada, Spain, were used. The coincidence criteria of ±300 km in space and ±12 h in time for H₂O, N₂O, and CH₄ and the coincidence criteria of ±300 km in space and ±6 h in time for ClONO₂, O₃, and HNO₃ were used. The ILAS-II data were separated into sunrise (= Northern Hemisphere and sunset (= Southern Hemisphere. For the sunrise data, a clear improvement from version 1.4 to version 2 was observed for H₂O, CH₄, ClONO₂, and O₃. In particular, the ILAS-II version 1.4 mixing ratios of H₂O and CH₄ were unrealistically small, and those of ClONO₂ above altitudes of 30 km unrealistically large. For N₂O and HNO₃, there were no large differences between the two versions. Contrary to the Northern Hemisphere, where some exceptional profiles deviated significantly from known climatology, no such outlying profiles were found in the Southern Hemisphere for both versions. Generally, the ILAS-II version 2 data were in better agreement with the MIPAS data than the version 1.4, and are recommended for quantitative analysis in the stratosphere. For H₂O data in the Southern Hemisphere, further data quality evaluation is necessary.

Validation of the Atmospheric Chemistry Experiment (ACE version 2.2 temperature using ground-based and space-borne measurements

Directory of Open Access Journals (Sweden)

R. J. Sica

2008-01-01

Full Text Available An ensemble of space-borne and ground-based instruments has been used to evaluate the quality of the version 2.2 temperature retrievals from the Atmospheric Chemistry Experiment Fourier Transform Spectrometer (ACE-FTS. The agreement of ACE-FTS temperatures with other sensors is typically better than 2 K in the stratosphere and upper troposphere and 5 K in the lower mesosphere. There is evidence of a systematic high bias (roughly 3–6 K in the ACE-FTS temperatures in the mesosphere, and a possible systematic low bias (roughly 2 K in ACE-FTS temperatures near 23 km. Some ACE-FTS temperature profiles exhibit unphysical oscillations, a problem fixed in preliminary comparisons with temperatures derived using the next version of the ACE-FTS retrieval software. Though these relatively large oscillations in temperature can be on the order of 10 K in the mesosphere, retrieved volume mixing ratio profiles typically vary by less than a percent or so. Statistical comparisons suggest these oscillations occur in about 10% of the retrieved profiles. Analysis from a set of coincident lidar measurements suggests that the random error in ACE-FTS version 2.2 temperatures has a lower limit of about ±2 K.

ANALYSIS OF PRINTING PARAMETERS FOR PRODUCTION OF COMPONENTS WITH ​EASY3DMAKER​ PRINTER

OpenAIRE

Alexander Rengevič; Mikuláš Fúra; Nadežda Čuboňová

2016-01-01

The presented article deals with analyses and testing appropriate parameters for the production of components manufactured with rapid prototyping technology - Easy3DMaker printer. The quality of the printed component with a specific shape is analyzed. The analyzed materials are ABS Printplus and PLA Printplus. These materials are printed at different temperatures and speeds. combinations of different settings were tested in order to find the best conditions for printing with different nozzles...

A primer on Hilbert space theory linear spaces, topological spaces, metric spaces, normed spaces, and topological groups

CERN Document Server

Alabiso, Carlo

2015-01-01

This book is an introduction to the theory of Hilbert space, a fundamental tool for non-relativistic quantum mechanics. Linear, topological, metric, and normed spaces are all addressed in detail, in a rigorous but reader-friendly fashion. The rationale for an introduction to the theory of Hilbert space, rather than a detailed study of Hilbert space theory itself, resides in the very high mathematical difficulty of even the simplest physical case. Within an ordinary graduate course in physics there is insufficient time to cover the theory of Hilbert spaces and operators, as well as distribution theory, with sufficient mathematical rigor. Compromises must be found between full rigor and practical use of the instruments. The book is based on the author's lessons on functional analysis for graduate students in physics. It will equip the reader to approach Hilbert space and, subsequently, rigged Hilbert space, with a more practical attitude. With respect to the original lectures, the mathematical flavor in all sub...

Fabrication of an interim complete removable dental prosthesis with an in-office digital light processing three-dimensional printer: A proof-of-concept technique.

Science.gov (United States)

Lin, Wei-Shao; Harris, Bryan T; Pellerito, John; Morton, Dean

2018-04-30

This report describes a proof of concept for fabricating an interim complete removable dental prosthesis with a digital light processing 3-dimensional (3D) printer. Although an in-office 3D printer can reduce the overall production cost for an interim complete removable dental prosthesis, the process has not been validated with clinical studies. This report provided a preliminary proof of concept in developing a digital workflow for the in-office additively manufactured interim complete removable dental prosthesis. Copyright © 2018 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Reward Anticipation in Ventral Striatum and Individual Sensitivity to Reward: A Pilot Study of a Child-Friendly fMRI Task.

Science.gov (United States)

van Hulst, Branko M; de Zeeuw, Patrick; Lupas, Kellina; Bos, Dienke J; Neggers, Sebastiaan F W; Durston, Sarah

2015-01-01

Reward processing has been implicated in developmental disorders. However, the classic task to probe reward anticipation, the monetary incentive delay task, has an abstract coding of reward and no storyline and may therefore be less appropriate for use with developmental populations. We modified the task to create a version appropriate for use with children. We investigated whether this child-friendly version could elicit ventral striatal activation during reward anticipation in typically developing children and young adolescents (aged 9.5-14.5). In addition, we tested whether our performance-based measure of reward sensitivity was associated with anticipatory activity in ventral striatum. Reward anticipation was related to activity in bilateral ventral striatum. Moreover, we found an association between individual reward sensitivity and activity in ventral striatum. We conclude that this task assesses ventral striatal activity in a child-friendly paradigm. The combination with a performance-based measure of reward sensitivity potentially makes the task a powerful tool for developmental imaging studies of reward processing.

The development of 3D food printer for printing fibrous meat materials

Science.gov (United States)

Liu, C.; Ho, C.; Wang, J.

2018-01-01

In this study, 3-D food printer was developed by integrating 3D printing technology with fibrous meat materials. With the help of computer-aided design and computer animation modeling software, users can model a desired pattern or shape, and then divide the model into layer-based sections. As the 3D food printer reads the design profile, food materials are extruded gradually through the nozzle to form the desired shape layer by layer. With the design of multiple nozzles, a wide variety of meat materials can be printed on the same product without the mixing of flavors. The technology can also extract the nutrients from the meat material to the food surface, allowing the freshness and sweetness of food to be tasted immediately upon eating it. This will also help the elderly’s eating experience since they often have bad teeth and poor taste sensing problems. Here, meat protein energy-type printing is used to solve the problem of currently available powder slurry calorie-type starch printing. The results show the novel technology development which uses pressurized tank with soft piping for material transport will improve the solid-liquid separation problem of fibrous meat material. In addition, the technology also allows amino acids from meat proteins as well as ketone body molecular substances from fatty acids to be substantially released, making ketogenic diet to be easier to accomplish. Moreover, time and volume controlled material feeding is made available by peristaltic pump to produce different food patterns and shapes with food materials of different viscosities, allowing food to be more eye-catching.

Pembuatan dan Karakterisasi Tinta Serbuk Printer Berbahan Baku Arang Aktif dari Limbah Padat Pengolahan Gambir

Directory of Open Access Journals (Sweden)

Yudo Purnomo

2017-12-01

Full Text Available Research on the utilization of tannins and catechins of gambier has been done a lot. There is no research report however that examines the utilization of gambier processing solid waste. The objective of the research was to utilize the solid waste of gambier processing as a raw material of printer toner. The research was done through pyrolysis process of solid waste with temperature variation 400, 500, 600oC and time variation 30, 60 minutes. The highest carbon content was obtained 42% with 400oC temperature and 60 minutes. The pyrolysis process of the gambier solid waste was further carried out at the optimum temperature and time. The charcoal was activated with H3PO4 at concentrations 0; 5; and 10% for 24 hours, cooled and washed to remove residual of H3PO4, then drying in the oven at temperature 115oC for 24 hours. Size reduction process used a ball milling for 2 hours with speed 500 rpm. Fixed carbon content was obtained between 43-51%. The results of morphological testing by scanning electron microscope showed that the produced carbon powder had not a uniform size yet. The average particle size was between 5-10 µm with polydispersity index 0.9. The most mineral elements of carbon powder analysis using XRF were Ca, Mg, K, Si, Fe, and P. Testing of print quality based on ISO/IEC 19752:2004 using laser jet printers had not provided optimal results yet.ABSTRAKPenelitian pemanfaatan tanin dan katekin gambir telah banyak dilakukan. Namun, belum dilaporkan penelitian yang mengkaji pemanfaatan limbah padat pengolahan gambir. Tujuan penelitian adalah memanfaatkan limbah padat pengolahan gambir sebagai bahan baku pembuatan tinta serbuk printer. Penelitian dilakukan melalui proses pirolisis limbah padat dengan variasi suhu 400, 500, 600oC dan variasi waktu 30, 60 menit. Kadar karbon terikat tertinggi diperoleh sebesar 42% dengan suhu pirolisis 400oC selama 60 menit. Proses pirolisis limbah padat gambir selanjutnya dilakukan pada suhu dan waktu optimal

Computerised output of phonetic codes in Devanagari script by dot-matrix printers

International Nuclear Information System (INIS)

Somasundaram, S.; Suri, M.M.K.; Khatua, R.

1987-01-01

This report describes the development of a computer software for converting hex-octal, alpha-numeric and pure-alpha mode input in English into 'phenetic Devanagari characters', which can be printed through dot-matrix printers in 2 passes of print-head, along with English text in the same lines. If multilingual terminals presently available in India, are used, it requires 4 passes of print-head for printing phonetic Devanagari characters, and English text also is converted into phonetic Devanagari script during printing. Thus, the software reported in this, is an improvement over the facilities currently available in Indian market. 9 tables, 2 refs. (author)

Characterization of Encapsulated Corrosion Inhibitors for Environmentally Friendly Smart Coatings

Science.gov (United States)

Pearman, B. P.; Calle, L. M.; Zhang, X.; Li, W.; Buhrow, J. W.; Johnsey, M. N.; Montgomery, E. L.; Fitzpatrick, L.; Surma, J. M.

2015-01-01

The NASA Kennedy Space Center's Corrosion Technology Lab at the Kennedy Space Center in Florida, U.S.A. has been developing multifunctional smart coatings based on the microencapsulation of environmentally friendly corrosion indicators, inhibitors and self-healing agents. This allows the incorporation of autonomous corrosion control functionalities, such as corrosion detection and inhibition as well as the self-healing of mechanical damage, into coatings. This paper presents technical details on the characterization of inhibitor-containing particles and their corrosion inhibitive effects using electrochemical and mass loss methods. Three organic environmentally friendly corrosion inhibitors were encapsulated in organic microparticles that are compatible with desired coatings. The release of the inhibitors from the microparticles in basic solution was studied. Fast release, for immediate corrosion protection, as well as long-term release for continued protection, was observed. The inhibition efficacy of the inhibitors, incorporated directly and in microparticles, on carbon steel was evaluated. Polarization curves and mass loss measurements showed that, in the case of 2MBT, its corrosion inhibition effectiveness was greater when it was delivered from microparticles.

Direct Investment Casting For Pattern Developed By Desktop 3D Printer

Directory of Open Access Journals (Sweden)

Marwah O.M.F.

2017-01-01

Full Text Available Development of RP technologies has encouraged rapid study on portable 3D Printer in which there are varieties of portable 3D printer machines in market. Nevertheless, less reports regarding its consumption of fabricated pattern to be used in direct investment casting. This study has focused on development of ABS P400 pattern in terms of collapsibility behaviour which has capability to be used as sacrificial pattern in direct investment casting. In addition, the internal built structures have been built into two designs such as square and polygon patterns respectively. The patterns were constructed in semi cylindrical geometry which comes with one side opened and one side closed together wrapped with 4 mm of ceramic shell. This experimental were conducted with variation temperature starting from 30°C until 150°C with increment of 5°C per minutes while for the numerical simulation, the temperature selected was between 30 °C to 120 °C with 10 °C increment per minutes. Moreover, the observation was made that glass transition temperature, Tg happened near 110°C. It was observed that the shell cracking happened on the ceramic shell. Other than that, the polygon pattern tends to collapsed inwardly rather than square pattern during the burnout process. A result also shows that, there is significant amount of stress reduction on both square and polygon which was 45 % respectively. Besides that, the amount of strain on pattern itself has shown about 9% reduction. Moreover, there is greater difference in terms of ceramic shell strain reduction which was 38% for square and polygon patterns respectively. Lastly, there is 11 % reduction of strain when compared square and polygon in terms of axial strain on ceramic shell

Curiosity rover LEGO® version could land soon

Science.gov (United States)

Showstack, Randy

2012-09-01

Now that NASA's Curiosity rover has landed on Mars, a smaller LEGO® plastic brick construction version could be landing in toy stores. Less than 2 weeks after Curiosity set down on 5 August, a LEGO® set concept model designed by a mechanical and aerospace engineer who worked on the real rover garnered its 10,000th supporter on the Web site of CUUSOO, a Japanese partner of the LEGO® group. That milestone triggered a company review that began in September 2012 to test the model's “playability, safety, and ft with the LEGO® brand,” according to a congratulatory statement from the company to designer Stephen Pakbaz. Pakbaz told Eos that he has been an avid LEGO® and space exploration fan for most of his life. “For me, creating a LEGO® model of Curiosity using my firsthand knowledge of the rover was inevitable. What I enjoyed most was being able to faithfully replicate and subsequently demonstrate the rocker-bogie suspension system to friends, family, and coworkers,” he noted, referring to the suspension system that allows the rover to climb over obstacles while keeping its wheels on the ground. Pakbaz, who is currently with Orbital Sciences Corporation, was involved with aspects of the rover while working at the Jet Propulsion Laboratory from 2007 to 2011 as a mechanical engineer.

Evaluation of usefulness and availability for orthopedic surgery using clavicle fracture model manufactured by desktop 3D printer

International Nuclear Information System (INIS)

Oh, Wang Kyun

2014-01-01

Usefulness and clinical availability for surgery efficiency were evaluated by conducting pre-operative planning with a model manufactured by desktop 3D printer by using clavicle CT image. The patient-customized clavicle fracture model was manufactured by desktop 3D printer of FDM wire laminated processing method by converting the CT image into STL file in Open Source DICOM Viewer Osirix. Also, the model of the original shape before damaged was restored and manufactured by Mirror technique based on STL file of not fractured clavicle of the other side by using the symmetry feature of the human body. For the model, the position and size, degree of the fracture was equally printed out. Using the clavicle model directly manufactured with low cost and less time in Department of Radiology is considered to be useful because it can reduce secondary damage during surgery and increase surgery efficiency with Minimal invasive percutaneous plate osteosynthesis(MIPO)

Evaluation of usefulness and availability for orthopedic surgery using clavicle fracture model manufactured by desktop 3D printer

Energy Technology Data Exchange (ETDEWEB)

Oh, Wang Kyun [Dept. of Diagnostic Radiology, Cheongju Medical Center, Cheongju (Korea, Republic of)

2014-09-15

Usefulness and clinical availability for surgery efficiency were evaluated by conducting pre-operative planning with a model manufactured by desktop 3D printer by using clavicle CT image. The patient-customized clavicle fracture model was manufactured by desktop 3D printer of FDM wire laminated processing method by converting the CT image into STL file in Open Source DICOM Viewer Osirix. Also, the model of the original shape before damaged was restored and manufactured by Mirror technique based on STL file of not fractured clavicle of the other side by using the symmetry feature of the human body. For the model, the position and size, degree of the fracture was equally printed out. Using the clavicle model directly manufactured with low cost and less time in Department of Radiology is considered to be useful because it can reduce secondary damage during surgery and increase surgery efficiency with Minimal invasive percutaneous plate osteosynthesis(MIPO)

Development of a user-friendly interface version of the Salmonella source-attribution model

DEFF Research Database (Denmark)

Hald, Tine; Lund, Jan

of travel and outbreak-related cases, also per country and subtype, ii) food-animal prevalence data per country and subtype, including the number of units tested and the number of positive units, and iii) data on the production and trade of the different food-animal sources in the EU Member States. The EFSA...... cases by subtype including data on the number of travel, domestic, unknown travel history and outbreak-related cases, also per subtype, ii) food-animal prevalence data per subtype, including the number of units tested and the number of positive units, and iii) data on the amount of the included animal...... for example in future mandates dealing with similar questions. The objective of the work described in this report was, therefore, to develop a flexible and user-friendly interface for attributing human cases of food-borne pathogens to the responsible food-animal reservoirs and/or food sources. The interface...

Environmentally Friendly Machining

CERN Document Server

Dixit, U S; Davim, J Paulo

2012-01-01

Environment-Friendly Machining provides an in-depth overview of environmentally-friendly machining processes, covering numerous different types of machining in order to identify which practice is the most environmentally sustainable. The book discusses three systems at length: machining with minimal cutting fluid, air-cooled machining and dry machining. Also covered is a way to conserve energy during machining processes, along with useful data and detailed descriptions for developing and utilizing the most efficient modern machining tools. Researchers and engineers looking for sustainable machining solutions will find Environment-Friendly Machining to be a useful volume.

A New Approach for Speckle Reduction in Holographic 3D printer

International Nuclear Information System (INIS)

Utsugi, Takeru; Yamaguchi, Masahiro

2013-01-01

A Holographic 3D printer produces a high quality 3D image reproduced by a full-color, full-parallax holographic stereogram with high-density light-ray recording. But speckle-pattern noise localized behind the reconstructed image is causing a loss of the display quality. This noise is originated from the speckle generated by a diffuser for equalizing the intensity distribution of the object light on the recording medium. We analyze some conventional ways for speckle reduction using a band-limited diffuser, and it is found that these ways cannot reduce the noise sufficiently. Then we propose two methods, one introduces a moving diffuser and the other introduces multiple exposures and a digital diffuser called as 4L-PRPS.

Fabrication of cerebral aneurysm simulator with a desktop 3D printer.

Science.gov (United States)

Liu, Yu; Gao, Qing; Du, Song; Chen, ZiChen; Fu, JianZhong; Chen, Bing; Liu, ZhenJie; He, Yong

2017-05-17

Now, more and more patients are suffering cerebral aneurysm. However, long training time limits the rapid growth of cerebrovascular neurosurgeons. Here we developed a novel cerebral aneurysm simulator which can be better represented the dynamic bulging process of cerebral aneurysm The proposed simulator features the integration of a hollow elastic vascular model, a skull model and a brain model, which can be affordably fabricated at the clinic (Fab@Clinic), under $25.00 each with the help of a low-cost desktop 3D printer. Moreover, the clinical blood flow and pulsation pressure similar to the human can be well simulated, which can be used to train the neurosurgical residents how to clip aneurysms more effectively.

Family Friendly Entrepreneurship: New Business Formation in Family Spaces

Directory of Open Access Journals (Sweden)

Carol Ekinsmyth

2012-01-01

Full Text Available Seventy three per cent of UK enterprises have no employees and seventeen per cent of these are managed solely by women (GEM UK Data 2005. UK female entrepreneurship is thus a significant economic phenomenon and it is increasing, especially in rural areas. Suggestions are that women’s businesses are different to men’s (Ahl 2006, Hanson 2003, Hanson and Blake 2004 in terms of their nature, location, type and the way that business is done. Limited empirical investigation has been undertaken, especially within geography (Hanson 2003. In addition, it has been argued that women’s participation in self-employment generally, is under-theorised (Blake, 2006; Ahl, 2006; Lewis 2006. Buzar et al (2005 identify the need to consider within this, the social construction of gender, time, space, economy and culture. This paper aims to advance knowledge and understanding of both the characteristics of female businesses and the coordinates and circumstances of female entrepreneurship. This paper will investigate the nature, dynamics, networks and locations of the new businesses (started up within the past five years of thirty women entrepreneurs all of whom are mothers and most of whom work at home. Two different types of new work/economic space will be examined. The first, the work locations of this economic activity, are a key defining feature of these businesses – they are typically the kitchens, bedroom and garages of the entrepreneurs’ family homes within the spaces of family life. An understanding of such enterprises is assisted by adopting a household-level, work-life reconciliation perspective (Jarvis 2005, Moen and Sweet 2004. The second new economic space reported in this paper will be the typical spaces of networking and marketing which often take place in electronic space, particularly the social networking sites (and especially female social and business networking, and mothers’ networking internet sites that have become so popular in the

Open-Source Wax RepRap 3-D Printer for Rapid Prototyping Paper-Based Microfluidics.

Science.gov (United States)

Pearce, J M; Anzalone, N C; Heldt, C L

2016-08-01

The open-source release of self-replicating rapid prototypers (RepRaps) has created a rich opportunity for low-cost distributed digital fabrication of complex 3-D objects such as scientific equipment. For example, 3-D printable reactionware devices offer the opportunity to combine open hardware microfluidic handling with lab-on-a-chip reactionware to radically reduce costs and increase the number and complexity of microfluidic applications. To further drive down the cost while improving the performance of lab-on-a-chip paper-based microfluidic prototyping, this study reports on the development of a RepRap upgrade capable of converting a Prusa Mendel RepRap into a wax 3-D printer for paper-based microfluidic applications. An open-source hardware approach is used to demonstrate a 3-D printable upgrade for the 3-D printer, which combines a heated syringe pump with the RepRap/Arduino 3-D control. The bill of materials, designs, basic assembly, and use instructions are provided, along with a completely free and open-source software tool chain. The open-source hardware device described here accelerates the potential of the nascent field of electrochemical detection combined with paper-based microfluidics by dropping the marginal cost of prototyping to nearly zero while accelerating the turnover between paper-based microfluidic designs. © 2016 Society for Laboratory Automation and Screening.

Design and Implementation of a Bio-printer for Cardiac Structures

Energy Technology Data Exchange (ETDEWEB)

Bravo, L.; Velasco, D.; Atienza, F.; Fernandez-Aviles, F.; Climent, A.M.; Liberos, A.

2016-07-01

Bio-printing has proven to be an excellent tool for the recently established field of Tissue Engineering and Regenerative Medicine (TERM) as it blends both principles of engineering and the life sciences to develop biological substitutes that restore or improve tissue function. The purpose of this work was to implement this new state of the art technology in the Laboratory of Organs and Bioartificial Matrices of the Gregorio Marañón Hospital, so as to aid in current research lines as well as open new fields of study. To do so, a commercial 3D Printer has been adapted following extrusion principles through a pressure driven mechanism. Cellular viability and geometrical fidelity have been assessed as the main parameters with which to determine the functional validity of the implemented technology. (Author)

Custom 3D printer and resin for 18 μm × 20 μm microfluidic flow channels.

Science.gov (United States)

Gong, Hua; Bickham, Bryce P; Woolley, Adam T; Nordin, Gregory P

2017-08-22

While there is great interest in 3D printing for microfluidic device fabrication, to-date the achieved feature sizes have not been in the truly microfluidic regime (uses a 385 nm LED, which dramatically increases the available selection of UV absorbers for resin formulation compared to 3D printers with 405 nm LEDs. Beginning with 20 candidate absorbers, we demonstrate the evaluation criteria and process flow required to develop a high-resolution resin. In doing so, we introduce a new mathematical model for characterizing the resin optical penetration depth based only on measurement of the absorber's molar absorptivity. Our final resin formulation uses 2-nitrophenyl phenyl sulfide (NPS) as the UV absorber. We also develop a novel channel narrowing technique that, together with the new resin and 3D printer resolution, enables small flow channel fabrication. We demonstrate the efficacy of our approach by fabricating 3D serpentine flow channels 41 mm long in a volume of only 0.12 mm 3 , and by printing high aspect ratio flow channels prototyping and fabrication.

Friends Like Me: Associations in Overweight/Obese Status among Adolescent Friends by Race/Ethnicity, Sex, and Friendship Type.

Science.gov (United States)

Bruening, Meg; MacLehose, Richard; Eisenberg, Marla E; Kim, Sunkyung; Story, Mary; Neumark-Sztainer, Dianne

2015-12-01

Little is known about how interpersonal friend relationships are associated with obesity in young people, particularly with regard to how race/ethnicity, type of friendship, and sex affect the association between friends' and adolescents' weight status. This study examined associations in weight status among adolescents and their friends, exploring magnitudes of associations across friendship type, sex, and race/ethnicity. As part of EAT-2010 (Eating and Activity in Teens), friend nominations and anthropometrics were obtained from adolescents (n = 2099: 54% female; 80% nonwhite; mean age: 14.2 ± 1.9 years). Generalized estimating equation logistic regression models were used to test associations between adolescents' overweight/obese status and friends' (i.e., friend group, female friends, male friends, female best friends, and male best friends) overweight/obese status. Interactions by adolescent race/ethnicity were examined. The majority of significant associations were observed among white female adolescents' who had a 22-40% higher prevalence of overweight/obesity if their friends were overweight compared to white females whose friends were not overweight. In contrast, there were few significant differences for other adolescent female and male racial/ethnic groups for girls and boys. Results for friend groups and best friends were generally similar to one another. The association between friend and adolescent overweight/obese status depended on adolescents' sex, race/ethnicity, and friendship type. Given the similarities among friends, obesity interventions targeting youth, especially white females, should consider involving friends.

Harmonic oscillator in Snyder space

Indian Academy of Sciences (India)

The harmonic oscillator in Snyder space is investigated in its classical and quantum versions. The classical trajectory is obtained and the semiclassical quantization from the phase space trajectories is discussed. An effective cut-off to high frequencies is found. The quantum version is developed and an equivalent usual ...

Integrated Procurement Management System, Version II

Science.gov (United States)

Collier, L. J.

1985-01-01

Integrated Procurement Management System, Version II (IPMS II) is online/ batch system for collecting developing, managing and disseminating procurementrelated data at NASA Johnson Space Center. Portions of IPMS II adaptable to other procurement situations.

Validation of the Brazilian Portuguese version of the pelvic floor bother questionnaire.

Science.gov (United States)

Peterson, Thais Villela; Pinto, Rodrigo Ambar; Davila, G Willy; Nahas, Sérgio Carlos; Baracat, Edmund Chada; Haddad, Jorge Milhem

2018-03-16

The Pelvic Floor Bother Questionnaire (PFBQ) was designed to identify the presence and degree of bother associated with common pelvic floor symptoms. The PFBQ can be used in clinical practice and for research purposes, but it is not available in Brazilian Portuguese. We aimed to validate a cross-culturally adapted Brazilian Portuguese version of the PFBQ. A pilot-tested version of the PFBQ translated from English was evaluated with Brazilian patients suffering from pelvic floor disorders. Internal reliability, test-retest reliability, validity, and responsiveness to change were assessed. A total of 147 patients (mean age, 60.49 years) were enrolled in the study. The Brazilian Portuguese version of the PFBQ demonstrated good reliability (α = 0.625; ICC = 0.981). There was strong agreement beyond chance for each item (κ = 0.895-1.00). The PFBQ correlated with stage of prolapse (p Portuguese version of the PFBQ is a reliable, valid, and user-friendly instrument that can be used for assessing the presence and severity of pelvic floor symptoms in clinical and research settings in Brazil.

Integrated Reliability and Risk Analysis System (IRRAS) Version 2.0 user's guide

International Nuclear Information System (INIS)

Russell, K.D.; Sattison, M.B.; Rasmuson, D.M.

1990-06-01

The Integrated Reliability and Risk Analysis System (IRRAS) is a state-of-the-art, microcomputer-based probabilistic risk assessment (PRA) model development and analysis tool to address key nuclear plant safety issues. IRRAS is an integrated software tool that gives the user the ability to create and analyze fault trees and accident sequences using a microcomputer. This program provides functions that range from graphical fault tree construction to cut set generation and quantification. Also provided in the system is an integrated full-screen editor for use when interfacing with remote mainframe computer systems. Version 1.0 of the IRRAS program was released in February of 1987. Since that time, many user comments and enhancements have been incorporated into the program providing a much more powerful and user-friendly system. This version has been designated IRRAS 2.0 and is the subject of this user's guide. Version 2.0 of IRRAS provides all of the same capabilities as Version 1.0 and adds a relational data base facility for managing the data, improved functionality, and improved algorithm performance. 9 refs., 292 figs., 4 tabs

Friend Finder (Game)

Science.gov (United States)

... for a spot on the Friend Finder All-Star List. Earn your spot by showing you're savvy when it comes to making friends online . Downloads Please download and share our ... Email Updates Blog Feed Facebook YouTube Twitter The Federal Trade Commission (FTC) is the ...

Stratified B-trees and versioning dictionaries

OpenAIRE

Twigg, Andy; Byde, Andrew; Milos, Grzegorz; Moreton, Tim; Wilkes, John; Wilkie, Tom

2011-01-01

A classic versioned data structure in storage and computer science is the copy-on-write (CoW) B-tree -- it underlies many of today's file systems and databases, including WAFL, ZFS, Btrfs and more. Unfortunately, it doesn't inherit the B-tree's optimality properties; it has poor space utilization, cannot offer fast updates, and relies on random IO to scale. Yet, nothing better has been developed since. We describe the `stratified B-tree', which beats all known semi-external memory versioned B...

Slicer Method Comparison Using Open-source 3D Printer

Science.gov (United States)

Ariffin, M. K. A. Mohd; Sukindar, N. A.; Baharudin, B. T. H. T.; Jaafar, C. N. A.; Ismail, M. I. S.

2018-01-01

Open-source 3D printer has been one of the popular choices in fabricating 3D models. This technology is easily accessible and low in cost. However, several studies have been made to improve the performance of this low-cost technology in term of the accuracy of the parts finish. This study is focusing on the selection of slicer mode between CuraEngine and Slic3r. The effect on this slicer has been observe in terms of accuracy and surface visualization. The result shows that if the accuracy is the top priority, CuraEngine is the better option to use as contribute more accuracy as well as less filament is needed compared to the Slice3r. Slice3r may be very useful for complicated parts such as hanging structure due to excessive material which act as support material. The study provides basic platform for the user to have an idea which option to be used in fabricating 3D model.

Validation of an uncertainty of illness scale adapted to use with Spanish emergency department patients and their accompanying relatives or friends.

Science.gov (United States)

Ruymán Brito-Brito, Pedro; García-Tesouro, Esther; Fernández-Gutiérrez, Domingo Ángel; García-Hernández, Alfonso Miguel; Fernández-Gutiérrez, Raquel; Burillo-Putze, Guillermo

2018-01-01

To validate a Spanish adaptation of the Mishel Uncertainty of Illness Scale for use with emergency-department (ED) patients and their accompanying relatives or friends (the UIS-ED). We first developed a version of the questionnaire for Spanish ED situations. Next we assessed the content validity index for each of its items, revised it, and reassessed its face validity to produce a second version, which we then piloted in 20 hospital ED patients. A third revised version was then validated in a population of 320 adults (160 patients and 160 accompanying persons) who attended the ED between November 2015 and September 2016. The 12-item UIS-ED (60 points) was administered by 2 nurses while the patients and accompanying persons were in the ED. We gathered sociodemographic and clinical data as well as the subjects' perception about the information they were given. The mean (SD) uncertainty score among patients was 29 (11) points. Accompanying persons had a mean score of 36 (13) points. Factorial analysis confirmed the instrument's construct validity, finding that both dimensions of the original Mishel scale (complexity and ambiguity) were present in 6 items each. Factorial analysis explained 60% of the total variance in the patient version and 67% of the variance in the version for accompanying persons. Reliability statistics were good, with Cronbach's α values ranging from 0.912 to 0.938. Split-half reliability statistics ranged from 0.901 to 0.933. Correlations were significant in the analysis of convergent validity. The UIS-ED questionnaire may prove to be a simple, valid, and reliable way for assessing uncertainty in patients and their accompanying friends or relatives attending Spanish EDs.

Assembly and use experience of a 3D printer in education

Directory of Open Access Journals (Sweden)

Ismael Orquín Serrano

2017-08-01

Full Text Available An academic experience consisting of mounting and using a 3d printer in the secondary school class of Technology is described. Also the methodology developed by teachers responsible of the project for tasks coordination as well as the way students interacted along their work, are explained. Different groups of students were formed in order to work in three different tasks: research task, documents development and assembly task. Each different task had its own teacher for guiding, assisting and assessing the student's work. This kind of innovative experiences are shown not only to motivate students but also to encourage them to face STEM (Science, Technology, Engineering and Mathematics projects from a wider perspective, integrating several areas of knowledge.

Technical Development of Slurry Three-Dimensional Printer

Science.gov (United States)

Jiang, Cho-Pei; Hsu, Huang-Jan; Lee, Shyh-Yuan

2017-09-01

The aim of this paper is to review the technical development of slurry three-dimensional printer (3DP) which based on photo-polymerization and constrained surface method. Basically, slurry consists of ceramic powder, resin and photo-initiator. The light engines for solidifying the photo-curable slurry can be classified as laser, liquid crystal panel (LCD), digital light processing (DLP). The slurry can be reacted and solidified by selective ray according to the reaction spectrum of photo-initiator. Ceramic powder used in this study is zirconia oxide. Experimental results show that ceramic particle size affects the viscosity of slurry severely resulting in low accuracy and the occurrence of micro crack in the layer casting procedure. Therefore, the effect of particle size on the curability and accuracy of built green part is discussed. A single dental crown is proposed to be fabricated by these three light engines as a benchmark for comparison. In addition, the cost and the limitation are compared in the aspect of dental crown fabrication. Consequently, the lowest cost is LCD-type slurry 3DP system. DLP-type slurry 3DP can produce green body with the fastest fabrication time. The volumetric error of sintered part that made by these three fabrication methods is similar because the composition of slurry is the same.

Aspirin Desensitization

Science.gov (United States)

... Nerve Decompression Dacryocystorhinostomy (DCR) Disclosure Statement Printer Friendly Aspirin Desensitization Kevin C. Welch, MD Zara Patel, MD Introduction The term "aspirin-sensitive asthma" (also known as "aspirin triad" or " ...

3D Printer Instrumentation to Create Varied Geometries of Robotic Limbs and Heterogeneous Granular Media

Science.gov (United States)

2015-05-20

Transfer Robo Ant The 3D printer was used to rapidly prototype a robot ant . The robot ant was used to model the behavior of the fire ant and to model...computer models and 3D printed ant robots are shown below. Snake Bot We used the 3D printed to rapidly design a modular, easily-modified snake...living organism (modern mudskippers, a terrestrial fish) and extinct early tetrapods (e.g. Ichthyostega, Acanthostega) while allowing us to explore

How open hardware drives digital fabrication tools such as the 3D printer

Directory of Open Access Journals (Sweden)

Johan Söderberg

2013-06-01

Full Text Available A case study of hobbyists developing a desktop 3D printer, indicative of a broader movement around open hardware development, is used to advance a theoretical apparatus drawing on social movement research. This is proposed as an alternative to how innovation by users is typically studied in innovation studies literature, namely, as discrete, isolated cases. Open hardware development projects make up a larger ecology, held together by common ideas, a shared communication infrastructure, conferences and licenses, among other things, and it therefore makes sense to look at them as part of a single movement.

Development turbine blade for ultramicro hydro power generation by 3D printer system

Science.gov (United States)

Kamimura, T.; Itoh, H.; Sugiura, K.

2017-11-01

We have developed micro generation system for effective use of unutilized energy and the spread of a self-controlled dispersion energy supply system. The turbine blade was designed for achieving high performance by special shape. The turbine type was called quasi-Peace turbine type. Turbine with a diameter of 30cm is made of metal, it was created by the 5-axis milling machine. The experimental apparatus was fabricated by the 3D printer. An experiment was carried out in the scale down model. The specific speed of this turbine was much lower than that of existing turbines.

Kernel versions of some orthogonal transformations

DEFF Research Database (Denmark)

Nielsen, Allan Aasbjerg

Kernel versions of orthogonal transformations such as principal components are based on a dual formulation also termed Q-mode analysis in which the data enter into the analysis via inner products in the Gram matrix only. In the kernel version the inner products of the original data are replaced...... by inner products between nonlinear mappings into higher dimensional feature space. Via kernel substitution also known as the kernel trick these inner products between the mappings are in turn replaced by a kernel function and all quantities needed in the analysis are expressed in terms of this kernel...... function. This means that we need not know the nonlinear mappings explicitly. Kernel principal component analysis (PCA) and kernel minimum noise fraction (MNF) analyses handle nonlinearities by implicitly transforming data into high (even infinite) dimensional feature space via the kernel function...

Genetic Algorithm and Graph Theory Based Matrix Factorization Method for Online Friend Recommendation

Directory of Open Access Journals (Sweden)

Qu Li

2014-01-01

Full Text Available Online friend recommendation is a fast developing topic in web mining. In this paper, we used SVD matrix factorization to model user and item feature vector and used stochastic gradient descent to amend parameter and improve accuracy. To tackle cold start problem and data sparsity, we used KNN model to influence user feature vector. At the same time, we used graph theory to partition communities with fairly low time and space complexity. What is more, matrix factorization can combine online and offline recommendation. Experiments showed that the hybrid recommendation algorithm is able to recommend online friends with good accuracy.

Scaffold-Free Tubular Tissues Created by a Bio-3D Printer Undergo Remodeling and Endothelialization when Implanted in Rat Aortae.

Science.gov (United States)

Itoh, Manabu; Nakayama, Koichi; Noguchi, Ryo; Kamohara, Keiji; Furukawa, Kojirou; Uchihashi, Kazuyoshi; Toda, Shuji; Oyama, Jun-Ichi; Node, Koichi; Morita, Shigeki

2015-01-01

Small caliber vascular prostheses are not clinically available because synthetic vascular prostheses lack endothelial cells which modulate platelet activation, leukocyte adhesion, thrombosis, and the regulation of vasomotor tone by the production of vasoactive substances. We developed a novel method to create scaffold-free tubular tissue from multicellular spheroids (MCS) using a "Bio-3D printer"-based system. This system enables the creation of pre-designed three-dimensional structures using a computer controlled robotics system. With this system, we created a tubular structure and studied its biological features. Using a "Bio-3D printer," we made scaffold-free tubular tissues (inner diameter of 1.5 mm) from a total of 500 MCSs (2.5× 104 cells per one MCS) composed of human umbilical vein endothelial cells (40%), human aortic smooth muscle cells (10%), and normal human dermal fibroblasts (50%). The tubular tissues were cultured in a perfusion system and implanted into the abdominal aortas of F344 nude rats. We assessed the flow by ultrasonography and performed histological examinations on the second (n = 5) and fifth (n = 5) day after implantation. All grafts were patent and remodeling of the tubular tissues (enlargement of the lumen area and thinning of the wall) was observed. A layer of endothelial cells was confirmed five days after implantation. The scaffold-free tubular tissues made of MCS using a Bio-3D printer underwent remodeling and endothelialization. Further studies are warranted to elucidate the underlying mechanism of endothelialization and its function, as well as the long-term results.

Eco-friendly Development Of Industry

International Nuclear Information System (INIS)

An, Gi Cheol; Park, Hun; Lee, Dong Jin; Ryu, Sang Hui

1998-02-01

This book reports eco-friendly development of industry, which has summary on bring up the issue and research way and system of research. It deals with current state of affairs on eco-friendly development of industry and the case of developed countries such as necessity and meaning of eco-friendly development industry, prospect and change of the tendency, environmental issue by field in Korea like the steel industry, nonferrous metal industry, auto industry, and cement industry and general policy for eco-friendly development of industry.

"Friends" of Anglican Cathedrals: Norms and Values. Befriending, Friending or Misnomer?

Science.gov (United States)

Muskett, Judith A.

2013-01-01

Loyal supporters of Anglican cathedrals first subscribed to "Friends" associations in the late 1920s. Yet, in 1937, a journalist in "The Times" portrayed cathedrals as a "queer thing to be a friend of." Drawing on theories of friendship from a range of disciplines, and surveys of what has been proclaimed in the public…

Friend networking sites and their relationship to adolescents' well-being and social self-esteem.

Science.gov (United States)

Valkenburg, Patti M; Peter, Jochen; Schouten, Alexander P

2006-10-01

The aim of this study was to investigate the consequences of friend networking sites (e.g., Friendster, MySpace) for adolescents' self-esteem and well-being. We conducted a survey among 881 adolescents (10-19-year-olds) who had an online profile on a Dutch friend networking site. Using structural equation modeling, we found that the frequency with which adolescents used the site had an indirect effect on their social self-esteem and well-being. The use of the friend networking site stimulated the number of relationships formed on the site, the frequency with which adolescents received feedback on their profiles, and the tone (i.e., positive vs. negative) of this feedback. Positive feedback on the profiles enhanced adolescents' social self-esteem and well-being, whereas negative feedback decreased their self-esteem and well-being.

Development of an organ-specific insert phantom generated using a 3D printer for investigations of cardiac computed tomography protocols.

Science.gov (United States)

Abdullah, Kamarul A; McEntee, Mark F; Reed, Warren; Kench, Peter L

2018-04-30

An ideal organ-specific insert phantom should be able to simulate the anatomical features with appropriate appearances in the resultant computed tomography (CT) images. This study investigated a 3D printing technology to develop a novel and cost-effective cardiac insert phantom derived from volumetric CT image datasets of anthropomorphic chest phantom. Cardiac insert volumes were segmented from CT image datasets, derived from an anthropomorphic chest phantom of Lungman N-01 (Kyoto Kagaku, Japan). These segmented datasets were converted to a virtual 3D-isosurface of heart-shaped shell, while two other removable inserts were included using computer-aided design (CAD) software program. This newly designed cardiac insert phantom was later printed by using a fused deposition modelling (FDM) process via a Creatbot DM Plus 3D printer. Then, several selected filling materials, such as contrast media, oil, water and jelly, were loaded into designated spaces in the 3D-printed phantom. The 3D-printed cardiac insert phantom was positioned within the anthropomorphic chest phantom and 30 repeated CT acquisitions performed using a multi-detector scanner at 120-kVp tube potential. Attenuation (Hounsfield Unit, HU) values were measured and compared to the image datasets of real-patient and Catphan ® 500 phantom. The output of the 3D-printed cardiac insert phantom was a solid acrylic plastic material, which was strong, light in weight and cost-effective. HU values of the filling materials were comparable to the image datasets of real-patient and Catphan ® 500 phantom. A novel and cost-effective cardiac insert phantom for anthropomorphic chest phantom was developed using volumetric CT image datasets with a 3D printer. Hence, this suggested the printing methodology could be applied to generate other phantoms for CT imaging studies. © 2018 The Authors. Journal of Medical Radiation Sciences published by John Wiley & Sons Australia, Ltd on behalf of Australian Society of Medical

Use of 3D printer model to study vertebral artery anatomy and variations in developmental craniovertebral junction anomalies and as a preoperative tool-an institutional experience.

Science.gov (United States)

Chhabra, Sachin; Chopra, Sanjeev; Kataria, Rashim; Sinha, Virendra Deo

2017-12-01

Spinal instrumentation using rods and screws have become procedure of choice for posterior fixation. Vertebral artery anatomy is highly variable in this region posing challenges during surgery. Our study used 3D printer model to understand the anatomy and variations in vertebral artery in live patients thereby providing an accurate idea about vertebral artery injury risk in these patients preoperatively and to rehearse the whole procedure. Ten patients of developmental craniovertebral junction (CVJ) anomalies who were planned for operative intervention in the Department of Neurosurgery at SMS Hospital from February 2016 to December 2016 were analysed using a 3D printer model. Out of twenty vertebral arteries studied in ten patients, two were hypoplastic and out of these one could not be appreciated on 3D printer model. Out of remaining nineteen, thirteen arteries were found to lie outside the joint, three were in lateral third, one traversed the middle third of joint and one lied in medial third. In one patient, the vertebral artery was stretched and it traversed horizontally over the joint. Out of ten patients studied, nine were having occipitalised atlas and so entry of these vertebral arteries into cranium were classified as given by Wang et al. into four types. By our study, 3D printer model was extremely helpful in analyzing joints and vertebral artery preoperatively and making the surgeon acquainted about the placement and trajectory of the screws accordingly. In our opinion, these models should be included as a basic investigation tool in these patients.

Use of 3D printer model to study vertebral artery anatomy and variations in developmental craniovertebral junction anomalies and as a preoperative tool—an institutional experience

Science.gov (United States)

Chopra, Sanjeev; Kataria, Rashim; Sinha, Virendra Deo

2017-01-01

Background Spinal instrumentation using rods and screws have become procedure of choice for posterior fixation. Vertebral artery anatomy is highly variable in this region posing challenges during surgery. Our study used 3D printer model to understand the anatomy and variations in vertebral artery in live patients thereby providing an accurate idea about vertebral artery injury risk in these patients preoperatively and to rehearse the whole procedure. Methods Ten patients of developmental craniovertebral junction (CVJ) anomalies who were planned for operative intervention in the Department of Neurosurgery at SMS Hospital from February 2016 to December 2016 were analysed using a 3D printer model. Results Out of twenty vertebral arteries studied in ten patients, two were hypoplastic and out of these one could not be appreciated on 3D printer model. Out of remaining nineteen, thirteen arteries were found to lie outside the joint, three were in lateral third, one traversed the middle third of joint and one lied in medial third. In one patient, the vertebral artery was stretched and it traversed horizontally over the joint. Out of ten patients studied, nine were having occipitalised atlas and so entry of these vertebral arteries into cranium were classified as given by Wang et al. into four types. Conclusions By our study, 3D printer model was extremely helpful in analyzing joints and vertebral artery preoperatively and making the surgeon acquainted about the placement and trajectory of the screws accordingly. In our opinion, these models should be included as a basic investigation tool in these patients. PMID:29354734

Manual centrifuge system: Bearing-based hand spinner made with 3-D printer.

Science.gov (United States)

Sun-Young Yoo; Seung Jae Lee; Jong-Mo Seo

2017-07-01

Compact disk (CD) Microfluidic platforms are being studied for medical applications such as blood tests. However, its size is bulky and electricity is needed to realize centrifuge force. In this paper, bearing-based hand spinner is designed using three-dimensional printer. This spinner does not need electricity and keeps rotating direction unlike paperfuge while it is spinning. The properties of spinner vary depending on bearing type which is positioned at the center. The type of weighting area also affects change in RPM over time. When a separation experiment is implemented, separating mixture into red ink and oil and whole blood into red blood cell and plasma are achieved properly with ceramic ball bearing.

光栅印刷加网的打印优化研究%Printer Optimization for Lenticular Screening

Institute of Scientific and Technical Information of China (English)

Jessica D. Armour; Daniel L. Lau; 张桂兰

2009-01-01

Digital Halftoning refers to any process used to convert continuous-tone images into an arrangement of black and white pixels, creating the illusion of a continuous-tone image. Lenticular screening is the process of multiplexing multiple images together column-wise into a single image which is then printed onto the flat side of a lenticular lens array such that from a given angle only one of the component images is visible. Lenticular screening presents a unique challenge to digital halftoning as a new generation of halftoning algorithms are needed in order to reduce the errors in lenticular prints caused by both lack of correlation between neighboring pixels and printer distortion. In this paper, we have addressed the issue of printer distortion, attempting to reduce error in lenticular prints by achieving a higher level of control over the printer being used for the print. We took into account the influence of a printed pixel on the resulting gray-level of surrounding pixels, adjusting printer resolution to account for dot overlap from various channels in order to reduce blurring within prints.%数字加网是指将连续调图像转换成由像素排列的图像的过程,使观察者产生一种连续调图像的错觉.光栅印刷加网是将组成柱面状的复用多张图像形成单一图像,然后打印到一个柱面透镜阵列的平面侧,这样从某一特定角度只能看到组合图像的一部分.为了减少光栅印刷中因相邻像素间缺乏关联和打印机失真而造成的误差,光栅印刷加网作为新一代的加网算法对数字加网提出挑战.在本论文中,讨论了打印机的失真问题,通过更好地控制打印机,达到光栅印刷中减少加网错误的目的.同时,考虑到打印像素对周围像素所产生的灰阶影响,通过各种方法调整打印机分辨率以解决网点重叠,从而减少打印图像模糊.

Anthropogenic Biomes of the World, Version 2: 1700

Data.gov (United States)

National Aeronautics and Space Administration — The Anthropogenic Biomes of the World, Version 2: 1700 data set describes anthropogenic transformations within the terrestrial biosphere caused by sustained direct...

Anthropogenic Biomes of the World, Version 2: 1900

Data.gov (United States)

National Aeronautics and Space Administration — The Anthropogenic Biomes of the World, Version 2: 1900 data set describes anthropogenic transformations within the terrestrial biosphere caused by sustained direct...

Anthropogenic Biomes of the World, Version 2: 1800

Data.gov (United States)

National Aeronautics and Space Administration — The Anthropogenic Biomes of the World, Version 2: 1800 data set describes anthropogenic transformations within the terrestrial biosphere caused by sustained direct...

Anthropogenic Biomes of the World, Version 2: 2000

Data.gov (United States)

National Aeronautics and Space Administration — The Anthropogenic Biomes of the World, Version 2: 2000 data set describes anthropogenic transformations within the terrestrial biosphere caused by sustained direct...

Preventing Elder Abuse and Neglect in Older Adults

Science.gov (United States)

... Documents PDF Preventing Elder Abuse and Neglect in Older Adults Download Join our e-newsletter! Resources Preventing Elder Abuse and Neglect in Older Adults Tools and Tips Printer-friendly PDF Click here ...

Marketing animal-friendly products

NARCIS (Netherlands)

Riemsdijk, van Lenka; Ingenbleek, Paul T.M.; Trijp, van Hans C.M.; Veen, van der Gerrita

2017-01-01

This article presents a conceptual framework that aims to encourage consumer animal-friendly product choice by introducing positioning strategies for animal-friendly products. These strategies reinforce the animal welfare with different types of consumption values and can therefore reduce

3D printing the pterygopalatine fossa: a negative space model of a complex structure.

Science.gov (United States)

Bannon, Ross; Parihar, Shivani; Skarparis, Yiannis; Varsou, Ourania; Cezayirli, Enis

2018-02-01

The pterygopalatine fossa is one of the most complex anatomical regions to understand. It is poorly visualized in cadaveric dissection and most textbooks rely on schematic depictions. We describe our approach to creating a low-cost, 3D model of the pterygopalatine fossa, including its associated canals and foramina, using an affordable "desktop" 3D printer. We used open source software to create a volume render of the pterygopalatine fossa from axial slices of a head computerised tomography scan. These data were then exported to a 3D printer to produce an anatomically accurate model. The resulting 'negative space' model of the pterygopalatine fossa provides a useful and innovative aid for understanding the complex anatomical relationships of the pterygopalatine fossa. This model was designed primarily for medical students; however, it will also be of interest to postgraduates in ENT, ophthalmology, neurosurgery, and radiology. The technical process described may be replicated by other departments wishing to develop their own anatomical models whilst incurring minimal costs.

A portable 3D printer system for the diagnosis and treatment of multidrug-resistant bacteria

OpenAIRE

Glatzel, Stefan; Hezwani, Mohammed; Kitson, Philip J.; Gromski, Piotr S.; Schürer, Sophie; Cronin, Leroy

2016-01-01

Summary: Multidrug-resistant bacteria are a major threat to human health, but broad-spectrum\\ud antibiotics are losing efficacy. There is a need to screen a given drug against\\ud a bacterial infection outside of the laboratory. To address this need, we have designed\\ud and built an inexpensive and easy-to-use 3D-printer-based system that\\ud allows easily readable quantitative tests for the performance of antibacterial\\ud drugs. The platform creates a sterile diagnostic device by using 3D prin...

WE-D-18A-05: Construction of Realistic Liver Phantoms From Patient Images and a Commercial 3D Printer

International Nuclear Information System (INIS)

Leng, S; Vrieze, T; Kuhlmann, J; Yu, L; Matsumoto, J; Morris, J; McCollough, C

2014-01-01

Purpose: To assess image quality and radiation dose reduction in abdominal CT imaging, physical phantoms having realistic background textures and lesions are highly desirable. The purpose of this work was to construct a liver phantom with realistic background and lesions using patient CT images and a 3D printer. Methods: Patient CT images containing liver lesions were segmented into liver tissue, contrast-enhanced vessels, and liver lesions using commercial software (Mimics, Materialise, Belgium). Stereolithography (STL) files of each segmented object were created and imported to a 3D printer (Object350 Connex, Stratasys, MN). After test scans were performed to map the eight available printing materials into CT numbers, printing materials were assigned to each object and a physical liver phantom printed. The printed phantom was scanned on a clinical CT scanner and resulting images were compared with the original patient CT images. Results: The eight available materials used to print the liver phantom had CT number ranging from 62 to 117 HU. In scans of the liver phantom, the liver lesions and veins represented in the STL files were all visible. Although the absolute value of the CT number in the background liver material (approx. 85 HU) was higher than in patients (approx. 40 HU), the difference in CT numbers between lesions and background were representative of the low contrast values needed for optimization tasks. Future work will investigate materials with contrast sufficient to emulate contrast-enhanced arteries. Conclusion: Realistic liver phantoms can be constructed from patient CT images using a commercial 3D printer. This technique may provide phantoms able to determine the effect of radiation dose reduction and noise reduction techniques on the ability to detect subtle liver lesions in the context of realistic background textures

WE-D-18A-05: Construction of Realistic Liver Phantoms From Patient Images and a Commercial 3D Printer

Energy Technology Data Exchange (ETDEWEB)

Leng, S; Vrieze, T; Kuhlmann, J; Yu, L; Matsumoto, J; Morris, J; McCollough, C [Mayo Clinic, Rochester, MN (United States)

2014-06-15

Purpose: To assess image quality and radiation dose reduction in abdominal CT imaging, physical phantoms having realistic background textures and lesions are highly desirable. The purpose of this work was to construct a liver phantom with realistic background and lesions using patient CT images and a 3D printer. Methods: Patient CT images containing liver lesions were segmented into liver tissue, contrast-enhanced vessels, and liver lesions using commercial software (Mimics, Materialise, Belgium). Stereolithography (STL) files of each segmented object were created and imported to a 3D printer (Object350 Connex, Stratasys, MN). After test scans were performed to map the eight available printing materials into CT numbers, printing materials were assigned to each object and a physical liver phantom printed. The printed phantom was scanned on a clinical CT scanner and resulting images were compared with the original patient CT images. Results: The eight available materials used to print the liver phantom had CT number ranging from 62 to 117 HU. In scans of the liver phantom, the liver lesions and veins represented in the STL files were all visible. Although the absolute value of the CT number in the background liver material (approx. 85 HU) was higher than in patients (approx. 40 HU), the difference in CT numbers between lesions and background were representative of the low contrast values needed for optimization tasks. Future work will investigate materials with contrast sufficient to emulate contrast-enhanced arteries. Conclusion: Realistic liver phantoms can be constructed from patient CT images using a commercial 3D printer. This technique may provide phantoms able to determine the effect of radiation dose reduction and noise reduction techniques on the ability to detect subtle liver lesions in the context of realistic background textures.

From Family to Friends: Does Witnessing Interparental Violence Affect Young Adults’ Relationships with Friends?

Science.gov (United States)

Mandal, Mahua; Hindin, Michelle J.

2013-01-01

Purpose Childhood exposure to violence in one’s family of origin has been closely linked to subsequent perpetration and victimization of intimate partner violence. There is, however, little research on the relationship between witnessing violence and subsequent peer violence. This study investigates the effects of witnessing interparental violence among Filipino young adults on their use and experience of psychological aggression with friends. Methods The data source for this study was the Cebu Longitudinal Health and Nutrition Survey. Recent perpetration and victimization of friend psychological aggression among young adults ages 21–22 years was assessed through self-reports from the 2005 survey, and witnessing interparental violence during childhood was assessed through self-reports from the 2002 survey. Multinomial logistic regression was used to examine the effects of witnessing interparental violence on subsequent use and experience of friend psychological aggression. Analyses were stratified by gender. Results About 13% of females and 4% of males perpetrated psychological aggression towards close friends, and about 4% of females and males were victims. Fourteen percent of females and 3% of males experienced bidirectional psychological aggression. About 44% of females and 47% of males had, during childhood, witnessed their parents physically hurt one another. Witnessing maternal and reciprocal interparental violence during childhood significantly predicted bidirectional friend psychological aggression among males. Among females, witnessing interparental violence did not significantly predict involvement with friend psychological aggression. Conclusions Violence prevention programs should consider using family-centered interventions, and apply a gendered lens to their application. Further research on gender differences in friend aggression is recommended. PMID:23697789

Analysis of Information Leakages on Laser Printers in the Media of Electromagnetic Radiation and Line Conductions

OpenAIRE

Ulaş, Cihan

2016-01-01

In this paper, the emissions of a laser printer, which may process classified information, are investigated in the media of electromagnetic radiation (ER), Power Line Conductors (PLC), and Signal Line Conductors (SLC). First, the candidate frequency points of CE are examined in the frequency domain. Second, the emitted signal is AM-demodulated with the proper bandwidth, and then sampled by a high storage oscilloscope in these frequency points. Third, the collected data is converted to 2D imag...

Dermatology Depictions in Friends/ Descripciones dermatológicas en Friends

Directory of Open Access Journals (Sweden)

Skyler M White

2017-03-01

Full Text Available Health?related topics are frequently referenced on screen in movies and television. Friends was on?air for 10 seasonsand is one of the most watched television shows of all time. Dermatology was referenced more than any otherhealth?related topic throughout the series. Beliefs about attractiveness and the stigma of skin conditions are furtherpropagated in this program. Reviewing the depictions of dermatology in Friends will aid in understanding the public’sideas and stereotypes regarding skin and dermatologic diseases.

Overview of MPLNET Version 3 Cloud Detection

Science.gov (United States)

Lewis, Jasper R.; Campbell, James; Welton, Ellsworth J.; Stewart, Sebastian A.; Haftings, Phillip

2016-01-01

The National Aeronautics and Space Administration Micro Pulse Lidar Network, version 3, cloud detection algorithm is described and differences relative to the previous version are highlighted. Clouds are identified from normalized level 1 signal profiles using two complementary methods. The first method considers vertical signal derivatives for detecting low-level clouds. The second method, which detects high-level clouds like cirrus, is based on signal uncertainties necessitated by the relatively low signal-to-noise ratio exhibited in the upper troposphere by eye-safe network instruments, especially during daytime. Furthermore, a multitemporal averaging scheme is used to improve cloud detection under conditions of a weak signal-to-noise ratio. Diurnal and seasonal cycles of cloud occurrence frequency based on one year of measurements at the Goddard Space Flight Center (Greenbelt, Maryland) site are compared for the new and previous versions. The largest differences, and perceived improvement, in detection occurs for high clouds (above 5 km, above MSL), which increase in occurrence by over 5%. There is also an increase in the detection of multilayered cloud profiles from 9% to 19%. Macrophysical properties and estimates of cloud optical depth are presented for a transparent cirrus dataset. However, the limit to which the cirrus cloud optical depth could be reliably estimated occurs between 0.5 and 0.8. A comparison using collocated CALIPSO measurements at the Goddard Space Flight Center and Singapore Micro Pulse Lidar Network (MPLNET) sites indicates improvements in cloud occurrence frequencies and layer heights.

Color digital halftoning taking colorimetric color reproduction into account

Science.gov (United States)

Haneishi, Hideaki; Suzuki, Toshiaki; Shimoyama, Nobukatsu; Miyake, Yoichi

1996-01-01

Taking colorimetric color reproduction into account, the conventional error diffusion method is modified for color digital half-toning. Assuming that the input to a bilevel color printer is given in CIE-XYZ tristimulus values or CIE-LAB values instead of the more conventional RGB or YMC values, two modified versions based on vector operation in (1) the XYZ color space and (2) the LAB color space were tested. Experimental results show that the modified methods, especially the method using the LAB color space, resulted in better color reproduction performance than the conventional methods. Spatial artifacts that appear in the modified methods are presented and analyzed. It is also shown that the modified method (2) with a thresholding technique achieves a good spatial image quality.

The Louvain printers and the establishment of the Cartesian curriculum

Directory of Open Access Journals (Sweden)

Geert Vanpaemel

2012-03-01

Full Text Available With regard to the public circulation of knowledge, universities are often regarded as privileged institutions where information and ideas are formally transmitted through regulated didactic experiences. University life, however, provided a more complex environment in which various parallel and perhaps contradictory processes of transmission were at work. In this paper, we analyse a set of 55 engravings with scientific images, which started to appear around 1670 in student notebooks at the University of Louvain. These engravings, produced and sold by the Louvain printers Michael Hayé and Lambert Blendeff, were related to the philosophy curriculum of the Faculty of Arts but did not correspond entirely to the actual topics or doctrine taught. In fact, the obvious Cartesian orientation of the images was not in line with the more prudent position of the Faculty. This paper offers a preliminary analysis of the set of engravings and their role in the Cartesian reforms at Louvain.

How to Make Financial Aid "Freshman-Friendly"

Science.gov (United States)

Pugh, Susan L.; Johnson, David B.

2011-01-01

Ultimately, making financial aid "freshman friendly" also makes financial aid "sophomore friendly," "junior friendly," and "senior friendly." Indiana University has in place an Office of Enrollment Management (OEM) model that includes focused financial aid packaging strategies complemented by unique contact…

Rehand: Realistic electric prosthetic hand created with a 3D printer.

Science.gov (United States)

Yoshikawa, Masahiro; Sato, Ryo; Higashihara, Takanori; Ogasawara, Tsukasa; Kawashima, Noritaka

2015-01-01

Myoelectric prosthetic hands provide an appearance with five fingers and a grasping function to forearm amputees. However, they have problems in weight, appearance, and cost. This paper reports on the Rehand, a realistic electric prosthetic hand created with a 3D printer. It provides a realistic appearance that is same as the cosmetic prosthetic hand and a grasping function. A simple link mechanism with one linear actuator for grasping and 3D printed parts achieve low cost, light weight, and ease of maintenance. An operating system based on a distance sensor provides a natural operability equivalent to the myoelectric control system. A supporter socket allows them to wear the prosthetic hand easily. An evaluation using the Southampton Hand Assessment Procedure (SHAP) demonstrated that an amputee was able to operate various objects and do everyday activities with the Rehand.

How to be a good visitor during flu season

Science.gov (United States)

... consumers How to be a good visitor during flu season 11/20/2017 Access a printer-friendly ... of infection prevention. This is especially true during flu season. According to the CDC, influenza (the flu) ...

NOAA/NSIDC Climate Data Record of Passive Microwave Sea Ice Concentration, Version 1

Data.gov (United States)

National Aeronautics and Space Administration — Note: If necessary, Version 1 can be accessed by contacting the NCDC service desk at ncdc.orders@noaa.gov. However, we highly suggest using the latest version of...

Design and Production of an Articulating Needle Guide for Ultrasound-Guided Needle Block Manufactured With a Three-Dimensional Printer: Technical Communication.

Science.gov (United States)

Bigeleisen, Paul E

2017-05-15

Needle guides may allow the practitioner to align the needle with the probe when ultrasound-guided nerve block is performed. The author's goal was to design and fabricate an inexpensive ($1.90), disposable, needle guide that could articulate over a range from 85 degrees to 0 degrees with a three-dimension printer. Three-dimensional representations of an L50, L25, and C 60 ultrasound probe (Sono Site, Bothell, WA) were created using a laser scanner. Computer-aided design software (Solid Works, Waltham, MA) was used to design a needle bracket and needle guide to attach to these probes. A three-dimensional printer was used to fabricate the needle bracket and guide with acrylonitrile polybutadiene polystyrene. An echogenic needle was held in plane with the needle guide. The author performed a supraclavicular block in a morbidly obese patient. The needle was easily visualized. Similar guides that are commercially available cost as much as $400. A knowledge of computer-aided design is necessary for this work.

Fermilab Friends for Science Education | Welcome

Science.gov (United States)

Fermilab Friends for Science Education FFSE Home About Us Join Us Support Us Contact Us Fermilab Friends for Science Education photo Fermilab Friends for Science Education supports innovative science education programs at Fermilab. Its mission is to: Enhance the quality of precollege science education in

Gender Norms and Institutional Culture: The Family-Friendly versus the Father-Friendly University

Science.gov (United States)

Sallee, Margaret W.

2013-01-01

This article investigates the role that gender norms and expectations about parenting play in establishing the family-friendly versus the father-friendly university. Using interviews with 51 male faculty at three research universities, the article considers how faculty and administrators' actions perpetuate cultures that promote or hinder…

Methodology for decision making in environmental restoration after nuclear accidents: temas system (version 2.1)

International Nuclear Information System (INIS)

Montero, M.; Moraleda, M.; Claver, F.; Vazquez, C.; Gutierrez, J.

2001-01-01

TEMAS is an user-friendly decision aiding computerised system to help in the selection of the best local strategy of restoration when a post-accidental environmental contamination with long lived radionuclides (''137 Cs and ''90 Sr) must be faced TEMAS provides answer for complex scenarios on whichever place of the European Community territory ( urban agricultural and forest) with different specific levels of contamination, uses and dimensions. The initial version was the result of the TEMAS project (Techniques and Management Strategies for Environmental Restoration) supported by the EU during the 4th Framework Program. Some Aspects of the methodology are at present being improved. This document applies to the computerised version 2.1 (VAZ01). (Author)

Global Rural-Urban Mapping Project (GRUMP), Alpha Version

Data.gov (United States)

National Aeronautics and Space Administration — The Global Rural-Urban Mapping Project (GRUMP), Alpha Version consists of estimates of human population for the years 1990, 1995, and 2000 by 30 arc-second (1km)...

Global Fertilizer and Manure, Version 1: Nitrogen Fertilizer Application

Data.gov (United States)

National Aeronautics and Space Administration — The Nitrogen Fertilizer Application dataset of the Global Fertilizer and Manure, Version 1 Data Collection represents the amount of nitrogen fertilizer nutrients...

Global Fertilizer and Manure, Version 1: Phosphorus Fertilizer Application

Data.gov (United States)

National Aeronautics and Space Administration — The Phosphorus Fertilizer Application dataset of the Global Fertilizer and Manure, Version 1 Data Collection represents the amount of phosphorus fertilizer nutrients...

Assistive Technology

Science.gov (United States)

... Page Resize Text Printer Friendly Online Chat Assistive Technology Assistive technology (AT) is any service or tool that helps ... be difficult or impossible. For older adults, such technology may be a walker to improve mobility or ...

The cost risk implementation on design-build project of integrated public spaces child friendly in capital of Jakarta

Science.gov (United States)

Mardiaman, Mubarok, Abdul

2017-11-01

Jakarta area of 662.33 km2 with a population of 10,075,030 inhabitants and green open spaces 9.98%. The Jakarta government built a child-friendly integrated open space as facilities for playing. Providing of facilities was hoped suitable with time, cost, quality, accountability and proper financial governance. Based on the PU ministerial regulation number 19/PRT/M/2015 on the standards and guidelines for procurement the design and construction work on the integrated build and the PU ministerial regulation No. 07/PRT/M/2011 on standards and guidelines for procurement of construction works and consulting services of public works and the ministry of housing. RPTRA development at 123 locations in Jakarta was implemented base on the contract of design and build. The design study was influenced by the cost elements; the main strength (expert), skilled personnel, support personnel, major equipment and support. The construction fee relies on; expert implementation, hardware implementation, preparation work, land, buildings, courtyards, fences, complementary and governance capabilities for human resources in completing the construction activities to minimize the cost risk. Montecarlo simulations was conducted to determine the average unit price, model and analyze systems. In the cost contract, the percentage of design work stipulated 2.5%, build 97.5%. Base on regulation the minister of public work for design work cost 2.72%, build 97.28%. Then, actual cost for design 2.67% and build 97.33%. From the three reference was shown that there are differentiation one another. The acceleration of planning able to make the cost and time more efficient that impact on the implementation margin.

From the printer: Potential of three-dimensional printing for orthopaedic applications

Directory of Open Access Journals (Sweden)

Sze-Wing Mok

2016-07-01

Full Text Available Three-dimensional (3D printers can create complex structures based on digital models. The combination of medical diagnostic imaging with 3D printing has great potential in day-to-day clinics for patient-specific solutions and applications. In the musculoskeletal system, 3D printing is used to create custom-made implants, patient-specific instrumentation, and to regenerate tissues, in particular bone and cartilage. The major limiting factors for bioprinting include the lack of printing techniques with optimal printing resolution and materials with ideal mechanical strengths while maintaining cellular functionality. Before “tissues from the printer” can be widely applied, further research and development on improving and optimising printing techniques and biomaterials, and knowledge on the development of printed constructs into living tissues, is essential for future clinical application of this technology.

Best friends' interactions and substance use: The role of friend pressure and unsupervised co-deviancy.

Science.gov (United States)

Tsakpinoglou, Florence; Poulin, François

2017-10-01

Best friends exert a substantial influence on rising alcohol and marijuana use during adolescence. Two mechanisms occurring within friendship - friend pressure and unsupervised co-deviancy - may partially capture the way friends influence one another. The current study aims to: (1) examine the psychometric properties of a new instrument designed to assess pressure from a youth's best friend and unsupervised co-deviancy; (2) investigate the relative contribution of these processes to alcohol and marijuana use; and (3) determine whether gender moderates these associations. Data were collected through self-report questionnaires completed by 294 Canadian youths (62% female) across two time points (ages 15-16). Principal component analysis yielded a two-factor solution corresponding to friend pressure and unsupervised co-deviancy. Logistic regressions subsequently showed that unsupervised co-deviancy was predictive of an increase in marijuana use one year later. Neither process predicted an increase in alcohol use. Results did not differ as a function of gender. Copyright © 2017 The Foundation for Professionals in Services for Adolescents. Published by Elsevier Ltd. All rights reserved.

Data output device of multichannel analyzers type SA40 and SA44 to ISOT-310 digital printer and D-102 puncher

International Nuclear Information System (INIS)

Ormandzhiev, S.; Semova, T.; Mishev, P.; Donkov, N.

1984-01-01

The chart of a device for data output from multichanel analyzers is described. Three data output modes are available: to a digital printer, to a puncher and to both of them. Circuit solution feature related to the specific analyzer requirements and external device applications are given. 3 figs.; 4 refs

OS Friendly Microprocessor Architecture

Science.gov (United States)

2017-04-01

NOTES Patrick La Fratta is now affiliated with Micron Technology, Inc., Boise, Idaho. 14. ABSTRACT We present an introduction to the patented ...Operating System Friendly Microprocessor Architecture (OSFA). The software framework to support the hardware-level security features is currently patent ...Army is assignee. OS Friendly Microprocessor Architecture. United States Patent 9122610. 2015 Sep. 2. Jungwirth P, inventor; US Army is assignee

Version pressure feedback mechanisms for speculative versioning caches

Science.gov (United States)

Eichenberger, Alexandre E.; Gara, Alan; O& #x27; Brien, Kathryn M.; Ohmacht, Martin; Zhuang, Xiaotong

2013-03-12

Mechanisms are provided for controlling version pressure on a speculative versioning cache. Raw version pressure data is collected based on one or more threads accessing cache lines of the speculative versioning cache. One or more statistical measures of version pressure are generated based on the collected raw version pressure data. A determination is made as to whether one or more modifications to an operation of a data processing system are to be performed based on the one or more statistical measures of version pressure, the one or more modifications affecting version pressure exerted on the speculative versioning cache. An operation of the data processing system is modified based on the one or more determined modifications, in response to a determination that one or more modifications to the operation of the data processing system are to be performed, to affect the version pressure exerted on the speculative versioning cache.

INCITS W1.1 development update: appearance-based image quality standards for printers

Science.gov (United States)

Zeise, Eric K.; Rasmussen, D. René; Ng, Yee S.; Dalal, Edul; McCarthy, Ann; Williams, Don

2008-01-01

In September 2000, INCITS W1 (the U.S. representative of ISO/IEC JTC1/SC28, the standardization committee for office equipment) was chartered to develop an appearance-based image quality standard. (1),(2) The resulting W1.1 project is based on a proposal (3) that perceived image quality can be described by a small set of broad-based attributes. There are currently six ad hoc teams, each working towards the development of standards for evaluation of perceptual image quality of color printers for one or more of these image quality attributes. This paper summarizes the work in progress of the teams addressing the attributes of Macro-Uniformity, Colour Rendition, Gloss & Gloss Uniformity, Text & Line Quality and Effective Resolution.

UCTM2: An updated User friendly Configurable Trigger, scaler and delay Module for nuclear and particle physics

Energy Technology Data Exchange (ETDEWEB)

Bourrion, O., E-mail: olivier.bourrion@lpsc.in2p3.fr; Boyer, B.; Derome, L.; Pignol, G.

2016-06-11

We developed a highly integrated and versatile electronic module to equip small nuclear physics experiments and lab teaching classes: the User friendly Configurable Trigger, scaler and delay Module for nuclear and particle physics (UCTM). It is configurable through a Graphical User Interface (GUI) and provides a large number of possible trigger conditions without any Hardware Description Language (HDL) required knowledge. This new version significantly enhances the previous capabilities by providing two additional features: signal digitization and time measurements. The design, performances and a typical application are presented.

Viability of Bioprinted Cellular Constructs Using a Three Dispenser Cartesian Printer.

Science.gov (United States)

Dennis, Sarah Grace; Trusk, Thomas; Richards, Dylan; Jia, Jia; Tan, Yu; Mei, Ying; Fann, Stephen; Markwald, Roger; Yost, Michael

2015-09-22

Tissue engineering has centralized its focus on the construction of replacements for non-functional or damaged tissue. The utilization of three-dimensional bioprinting in tissue engineering has generated new methods for the printing of cells and matrix to fabricate biomimetic tissue constructs. The solid freeform fabrication (SFF) method developed for three-dimensional bioprinting uses an additive manufacturing approach by depositing droplets of cells and hydrogels in a layer-by-layer fashion. Bioprinting fabrication is dependent on the specific placement of biological materials into three-dimensional architectures, and the printed constructs should closely mimic the complex organization of cells and extracellular matrices in native tissue. This paper highlights the use of the Palmetto Printer, a Cartesian bioprinter, as well as the process of producing spatially organized, viable constructs while simultaneously allowing control of environmental factors. This methodology utilizes computer-aided design and computer-aided manufacturing to produce these specific and complex geometries. Finally, this approach allows for the reproducible production of fabricated constructs optimized by controllable printing parameters.

Green hypocrisy? Environmental attitudes and residential space heating expenditure

Energy Technology Data Exchange (ETDEWEB)

Traynor, Laura; Lange, Ian; Moro, Mirko [Stirling Univ. (United Kingdom). Division of Economics

2012-06-15

In the UK, the largest proportion of household energy use is for space heating. Popular media make claims of a green hypocrisy: groups which have the strongest attitude towards the environment have the highest emissions. This study examines whether environmental attitudes and behaviours are associated with space heating energy use using data from the British Household Panel Survey. Results find that environmentally friendly attitudes generally do not lead to lower heating expenditures though environmentally friendly behaviours are associated with lower heating expenditure. Also, the effect of these attitudes and behaviours do not change as income increase.

User friendly packaging

DEFF Research Database (Denmark)

Geert Jensen, Birgitte

2010-01-01

Most consumers have experienced occasional problems with opening packaging. Tomato sauce from the tinned mackerel splattered all over the kitchen counter, the unrelenting pickle jar lid, and the package of sliced ham that cannot be opened without a knife or a pair of scissors. The research project...... “User-friendly Packaging” aims to create a platform for developing more user-friendly packaging. One intended outcome of the project is a guideline that industry can use in development efforts. The project also points the way for more extended collaboration between companies and design researchers. How...... can design research help industry in packaging innovation?...

75 FR 63851 - Draft Friends Organizations Policy

Science.gov (United States)

2010-10-18

...] Draft Friends Organizations Policy AGENCY: Fish and Wildlife Service, Department of the Interior. ACTION... Service's mission through partnerships with Friends organizations (volunteer/advocate). Today, Friends organizations play a vital role in helping to fulfill the Service's mission of ``working with others, to...

The Use of a 3D Printer in Pre-operative Planning for a Patient Requiring Acetabular Reconstructive Surgery.

Science.gov (United States)

Duncan, James M; Nahas, Samuel; Akhtar, Kashif; Daurka, Jasvinder

2015-01-01

Surgical management of acetabular fractures is often highly complex, and a successful outcome depends upon an appreciation of the fracture pattern and the most appropriate approach to reduce and hold it. Currently, computed tomography (CT) images are used in conjunction with plain x-rays to identify the main fracture components and their spatial relationship to one another, and as such surgeons still have to make decisions based upon their ability to visualise the fracture from the images available. 3D printers have now become widely available and inexpensive, and can be used to rapidly produce life-size models based on CT scans of an individual patient. The availability of patient specific, accurate and detailed models of complex acetabular fractures can aid planning of surgical management on a patient specific basis. This report describes the use of a 3D printer to create a life-size model reconstruction of the pelvis of a 48 year old male patient who sustained a left sided associated both column acetabular fracture following a motorbike accident in the Sahara Desert. The model allowed visualisation of the multiple fracture fragments and their relative displacements. The tactile feedback allowed assessment of the different fracture fragments. The relative displacement of the quadrilateral plate and posterior column fragments could be assessed and the surgeon felt that these would be amenable to reduction from an ilioinguinal approach. An anatomic reduction was achieved and was held with the application of a pelvic brim plate with 2 screws lagging the posterior column/quadrilateral plate fragment. There are previous examples of 3D models being used in orthopaedic surgery through the use of rapid prototyping, however this method is usually expensive and time consuming. Advances in 3D printer technology offer surgeons a number of advantages when treating these complex fractures. With the ever-increasing economy, ease of use and speed of additive processing, the

Differentiation of Entamoeba histolytica, Entamoeba dispar and ...

African Journals Online (AJOL)

2016-06-28

Jun 28, 2016 ... Social Sciences) program for Windows version 17 .... A study in Brazil showed that the prevalence of .... User-friendly online submission • Rigorous, constructive and unbiased peer-review • No space constraints or coloured.

The ESA/ESO/NASA Photoshop fits Liberator Version 2

Science.gov (United States)

Christensen, L. L.; Nielsen, L. H.; Nielsen, K. K.; Johansen, T.

2005-12-01

Since the fi rst version of the FITS Liberator software was released on the 8th July 2004 more than 50,000 people worldwide have looked over the scientists' shoulders and worked with digital images from telescopes in space and on the ground themselves. In this way the Liberator has become the `industry standard' for the production of astronomical colour images. The new version 2 of the software has recently been released and opens up a signifi cant number of new possibilities.

Selected Tether Applications Cost Model

Science.gov (United States)

Keeley, Michael G.

1988-01-01

Diverse cost-estimating techniques and data combined into single program. Selected Tether Applications Cost Model (STACOM 1.0) is interactive accounting software tool providing means for combining several independent cost-estimating programs into fully-integrated mathematical model capable of assessing costs, analyzing benefits, providing file-handling utilities, and putting out information in text and graphical forms to screen, printer, or plotter. Program based on Lotus 1-2-3, version 2.0. Developed to provide clear, concise traceability and visibility into methodology and rationale for estimating costs and benefits of operations of Space Station tether deployer system.

Operative simulation of anterior clinoidectomy using a rapid prototyping model molded by a three-dimensional printer.

Science.gov (United States)

Okonogi, Shinichi; Kondo, Kosuke; Harada, Naoyuki; Masuda, Hiroyuki; Nemoto, Masaaki; Sugo, Nobuo

2017-09-01

As the anatomical three-dimensional (3D) positional relationship around the anterior clinoid process (ACP) is complex, experience of many surgeries is necessary to understand anterior clinoidectomy (AC). We prepared a 3D synthetic image from computed tomographic angiography (CTA) and magnetic resonance imaging (MRI) data and a rapid prototyping (RP) model from the imaging data using a 3D printer. The objective of this study was to evaluate anatomical reproduction of the 3D synthetic image and intraosseous region after AC in the RP model. In addition, the usefulness of the RP model for operative simulation was investigated. The subjects were 51 patients who were examined by CTA and MRI before surgery. The size of the ACP, thickness and length of the optic nerve and artery, and intraosseous length after AC were measured in the 3D synthetic image and RP model, and reproducibility in the RP model was evaluated. In addition, 10 neurosurgeons performed AC in the completed RP models to investigate their usefulness for operative simulation. The RP model reproduced the region in the vicinity of the ACP in the 3D synthetic image, including the intraosseous region, at a high accuracy. In addition, drilling of the RP model was a useful operative simulation method of AC. The RP model of the vicinity of ACP, prepared using a 3D printer, showed favorable anatomical reproducibility, including reproduction of the intraosseous region. In addition, it was concluded that this RP model is useful as a surgical education tool for drilling.

[Fostering LGBT-friendly healthcare services].

Science.gov (United States)

Wei, Han-Ting; Chen, Mu-Hong; Ku, Wen-Wei

2015-02-01

LGBT (lesbian, gay, bisexual, transgender) patients suffer from stigma and discrimination when seeking healthcare. A large LGBT healthcare survey revealed that 56% of gay patients and 70% of transgender patients suffered some type of discrimination while seeking healthcare in 2014. The fostering of LGBT-friendly healthcare services is not just an advanced step of gender mainstreaming but also a fulfillment of health equality and equity. Additionally, LGBT-friendly healthcare services are expected to provide new opportunities for healthcare workers. Therefore, proactive government policies, education, research, and clinical practice should all encourage the development of these healthcare services. We look forward to a well-developed LGBT-friendly healthcare system in Taiwan.

The multi-physics, user-friendly gas-dynamics code Visual Tsunami 2.0

International Nuclear Information System (INIS)

Debonnel, C. S.; Trubov, L.; Zeballos, C. A.; Peterson, P. F.

2007-01-01

Since the early 1990's, the series of simulation code known as TSUNAMI has been the main tool employed to explore gas dynamics phenomena in thick-liquid protected inertial fusion target chambers. The applicability and user-friendliness of the code was recently extended through a set of MATLAB pre- and post-processing tools and graphical user interfaces [1]. Geometry, initial, and boundary conditions can be specified from within AutoCAD through a set of in-house AutoLISP graphical user interfaces. A novel MATLAB core was recently developed and tested, and is now routinely used with the user-friendly pre- and post-processors [2]. An overview of Visual Tsunami 2.0, the latest version of the code, is presented here. (authors)

Show me your friends and I will tell you what type of person you are: how own profile, number of friends, and type of friends influence impression formation on social network sites

NARCIS (Netherlands)

Utz, S.

2010-01-01

This experiment examines how far extraversion of the target (self-generated information), extraversion of the target's friends (friends-generated information), and number of friends (system-generated information) influence the perceived popularity, communal orientation, and social attractiveness of

Requirement analysis and sensor specifications – First version

NARCIS (Netherlands)

Sharma, Puneet; Wild, Fridolin; Klemke, Roland; Helin, Kaj; Azam, Tre

2017-01-01

In this first version of the deliverable, we make the following contributions: to design the WEKIT capturing platform and the associated experience capturing API, we use a methodology for system engineering that is relevant for different domains such as: aviation, space, and medical and different

UPC Language and Library Specifications, Version 1.3

Energy Technology Data Exchange (ETDEWEB)

UPC Consortium; Bonachea, Dan; Funck, Gary

2013-11-16

UPC is an explicitly parallel extension to the ISO C 99 Standard. UPC follows the partitioned global address space programming model. This document is the formal specification for the UPC language and library syntax and semantics, and supersedes prior specification version 1.2 (LBNL-59208).

Use of 3D printers to create a patient‐specific 3D bolus for external beam therapy

Science.gov (United States)

Baker, Jamie; Hsia, An Ting; Xu, Zhigang

2015-01-01

The purpose of this paper is to demonstrate that an inexpensive 3D printer can be used to manufacture patient‐specific bolus for external beam therapy, and to show we can accurately model this printed bolus in our treatment planning system for accurate treatment delivery. Percent depth‐dose measurements and tissue maximum ratios were used to determine the characteristics of the printing materials, acrylonitrile butadiene styrene and polylactic acid, as bolus material with physical density of 1.04 and 1.2 g/cm3, and electron density of 3.38×1023electrons/cm3 and 3.80×1023 electrons/cm3, respectively. Dose plane comparisons using Gafchromic EBT2 film and the RANDO phantom were used to verify accurate treatment planning. We accurately modeled a printing material in Eclipse treatment planning system, assigning it a Hounsfield unit of 260. We were also able to verify accurate treatment planning using gamma analysis for dose plane comparisons. With gamma criteria of 5% dose difference and 2 mm DTA, we were able to have 86.5% points passing, and with gamma criteria of 5% dose difference and 3 mm DTA, we were able to have 95% points passing. We were able to create a patient‐specific bolus using an inexpensive 3D printer and model it in our treatment planning system for accurate treatment delivery. PACS numbers: 87.53.Jw, 87.53.Kn, 87.56.ng PMID:26103485

Hispanic Labor Friends Initiative: supporting vulnerable women.

Science.gov (United States)

Hazard, Cambria Jones; Callister, Lynn Clark; Birkhead, Ana; Nichols, Lisa

2009-01-01

To evaluate the qualitative aspects of the Hispanic Labor Friends Initiative. "Hispanic Labor Friends," bilingual Hispanic community women who were themselves mothers, were recruited by clinic and hospital personnel. Women who agreed were educated, received translation certification, and were oriented to the initiative. Pregnant Hispanic immigrant women seen in the health center who met criteria set by the multidisciplinary health care team were assigned a Hispanic Labor Friend by 32 weeks' gestation. Hispanic Labor Friends assisted women with communication with healthcare providers and provided social support. Qualitative evaluation of the program consisted of interviews with several groups: (1) Hispanic immigrant women who had a Hispanic Labor Friend, (2) Hispanic immigrant women who were not in the Hispanic Labor Friends program, (3) Hispanic Labor Friends, (4) healthcare providers for Hispanic women. Data saturation was reached, and data were analyzed by the research team using descriptive qualitative inquiry. The Hispanic immigrant women described positive outcomes from being involved in the Hispanic Labor Friends program, including feeling supported and comforted. "I felt as though my family were at my side." One woman who had standard care said, "It is hard for me to communicate. When I gave birth, the nurses asked me things, and I didn't understand anything. I stayed quiet." One of the nurses who was interviewed said: "I think they [the HLF patients] get better care. Sometimes we think we can communicate with them with their little bit of English and our little bit of Spanish. But you get an HLF and it's a totally different story. We can more adequately tell what's going on with them...They end up getting better care." One Hispanic Labor Friend said, "The women are very appreciative that I was there to help them through a critical time." Women who participated in the study identified the need to have a continuing association with Hispanic Labor Friends in

WE-F-16A-05: Use of 3D-Printers to Create a Tissue Equivalent 3D-Bolus for External Beam Therapy

Energy Technology Data Exchange (ETDEWEB)

Burleson, S; Baker, J; Hsia, A; Xu, Z [Stony Brook Medicine, Stony Brook, NY (United States)

2014-06-15

Purpose: The purpose of this project is to demonstrate that a non-expensive 3D-printer can be used to manufacture a 3D-bolus for external beam therapy. The printed bolus then can be modeled in our treatment planning system to ensure accurate dose delivery to the patient. Methods: We developed a simple method to manufacture a patient-specific custom 3Dbolus. The bolus is designed using Eclipse Treatment Planning System, contoured onto the patients CT images. The bolus file is exported from Eclipse to 3D-printer software, and then printed using a 3D printer. Various tests were completed to determine the properties of the printing material. Percent depth dose curves in this material were measured with electron and photon beams for comparison to other materials. In order to test the validity of the 3D printed bolus for treatment planning, a custom bolus was printed and tested on the Rando phantom using film for a dose plane comparison. We compared the dose plane measured on the film to the same dose plane exported from our treatment planning system using Film QA software. The gamma-dose distribution tool was used in our film analysis. Results: We compared point measurements throughout the dose plane and were able to achieve greater than 95% passing rate at 3% dose difference and 3 mm distance to agreement, which is our departments acceptable gamma pixel parameters. Conclusion: The printed 3D bolus has proven to be accurately modeled in our treatment planning system, it is more conformal to the patient surface and more durable than other bolus currently used (wax, superflab etc.). It is also more convenient and less costly than comparable bolus from milling machine companies.

WE-F-16A-05: Use of 3D-Printers to Create a Tissue Equivalent 3D-Bolus for External Beam Therapy

International Nuclear Information System (INIS)

Burleson, S; Baker, J; Hsia, A; Xu, Z

2014-01-01

Purpose: The purpose of this project is to demonstrate that a non-expensive 3D-printer can be used to manufacture a 3D-bolus for external beam therapy. The printed bolus then can be modeled in our treatment planning system to ensure accurate dose delivery to the patient. Methods: We developed a simple method to manufacture a patient-specific custom 3Dbolus. The bolus is designed using Eclipse Treatment Planning System, contoured onto the patients CT images. The bolus file is exported from Eclipse to 3D-printer software, and then printed using a 3D printer. Various tests were completed to determine the properties of the printing material. Percent depth dose curves in this material were measured with electron and photon beams for comparison to other materials. In order to test the validity of the 3D printed bolus for treatment planning, a custom bolus was printed and tested on the Rando phantom using film for a dose plane comparison. We compared the dose plane measured on the film to the same dose plane exported from our treatment planning system using Film QA software. The gamma-dose distribution tool was used in our film analysis. Results: We compared point measurements throughout the dose plane and were able to achieve greater than 95% passing rate at 3% dose difference and 3 mm distance to agreement, which is our departments acceptable gamma pixel parameters. Conclusion: The printed 3D bolus has proven to be accurately modeled in our treatment planning system, it is more conformal to the patient surface and more durable than other bolus currently used (wax, superflab etc.). It is also more convenient and less costly than comparable bolus from milling machine companies

Compendium of Environmental Sustainability Indicator Collections: Complete Collection, Version 1.1

Data.gov (United States)

National Aeronautics and Space Administration — The Compendium of Environmental Sustainability Indicator Collections, Version 1.1 contains 426 indicators for 239 countries from five major environmental...

Critical friends and collaborative partnership

Directory of Open Access Journals (Sweden)

Katarina Jandér

2013-12-01

Full Text Available Critical friends: a method for peer feedback The Critical Friend-method has been used in various educational settings to facilitate the process of continuous improvement in teaching. The aim of this study was to implement Critical Friends, and to find out if this method could be used for feedback on teaching as part of a librarians' professional development. The project was carried out within the Library Unit of the Faculty of Medicine at Lund University, Sweden, in collaboration with the faculty's Centre for Teaching and Learning. Seven librarians and an educational consultant from the Centre for Teaching and Learning participated; the educational consultant played an essential role in supervising and structuring the project and the evaluation process, preparing readings as well as being an active participant. The participants worked in pairs; the performance of one teacher and the associated classroom activities were observed by the critical friend, and then evaluated and discussed. Evaluation and results After two preparatory group meetings, a final meeting was held where all pairs reported what they had done and how they perceived the critical friend process. The experiences of the participating librarians were explored using a questionnaire. The questionnaire was analyzed using content analysis by one librarian and the educational consultant independently. The results suggested that use of the critical friend method could have a positive impact by achieving the following: strengthening shared values concerning teaching issues; promoting self-reflection on teaching; facilitating communication with colleagues; and reducing the sense of 'loneliness‘ in teaching. The difficulties in the implementation were lack of time and competing duties. It was perceived as an advantage to work in close partnership with the faculty's educational consultants, who were familiar with the organization.

Friend Effects and Racial Disparities in Academic Achievement

Directory of Open Access Journals (Sweden)

Jennifer Flashman

2014-07-01

Full Text Available Racial disparities in achievement are a persistent fact of the US educational system. An often cited but rarely directly studied explanation for these disparities is that adolescents from different racial and ethnic backgrounds are exposed to different peers and have different friends. In this article I identify the impact of friends on racial and ethnic achievement disparities. Using data from Add Health and an instrumental variable approach, I show that the achievement characteristics of youths’ friends drive friend effects; adolescents with friends with higher grades are more likely to increase their grades compared to those with lower-achieving friends. Although these effects do not differ across race/ethnicity, given differences in friendship patterns, if black and Latino adolescents had friends with the achievement characteristics of white students, the GPA gap would be 17 to 19 percent smaller. Although modest, this effect represents an important and often overlooked source of difference among black and Latino youth.

To friend or not to friend? Social networking and faculty perceptions of online professionalism.

Science.gov (United States)

Chretien, Katherine C; Farnan, Jeanne M; Greysen, S Ryan; Kind, Terry

2011-12-01

To assess faculty perceptions of professional boundaries and trainee-posted content on social networking sites (SNS). In June 2010, the Clerkship Directors in Internal Medicine conducted its annual survey of U.S. and Canadian member institutions. The survey included sections on demographics and social networking. The authors used descriptive statistics and tests of association to analyze the Likert scale responses and qualitatively analyzed the free-text responses. Of 110 institutional members, 82 (75%) responded to the survey. Of the 40 respondents who reported current or past SNS use, 21 (53%) reported receiving a "friend request" from a current student and 25 (63%) from a current resident. Of these, 4 (19%) accepted the student request and 12 (48%) accepted the resident request. Sixty-three of 80 (79%) felt it was inappropriate to send a friend request to a current student, 61 (76%) to accept a current student's request, 42 (53%) to become friends with a current resident, and 61 (81%) to become friends with a current patient. Becoming friends with a former student, former resident, or colleague was perceived as more appropriate. Younger respondents were less likely to deem specific student behaviors inappropriate (odds ratio [OR] 0.18-0.79; adjusted OR 0.12-0.86, controlling for respondents' sex, rank, and SNS use), although none reached statistical significance. Some internal medicine educators are using SNSs and interacting with trainees online. Their perceptions on the appropriateness of social networking behaviors provide some consensus for professional boundaries between faculty and trainees in the digital world.

Project ARGO: The design and analysis of an all-propulsive and an aeroassisted version of a manned space transportation vehicle

Science.gov (United States)

Wang, H.; Seifert, D.; Waidelich, J.; Mileski, M.; Herr, D.; Wilks, M.; Law, G.; Folz, A.

1989-01-01

The Senior Aerospace System Design class at the University of Michigan undertook the design of a manned space transportation vehicle (STV) that would transport payloads between low earth orbit (LEO) and geosynchronous earth orbit (GEO). Designated ARGO after the ship of the Greek adventurer Jason, two different versions of an STV that would be based, refueled, and serviced at the Space Station Freedom were designed and analyzed by the class. With the same 2-man/7-day nominal mission of transporting a 10,000-kg payload up to GEO and bringing a 5000-kg payload back to LEO, the two versions of ARGO differ in the manner in which the delta V is applied to insert the vehicle into LEO upon return from GEO. The all-propulsive ARGO (or CSTV for chemical STV) uses thrust from its LH2/LOX rocket engines to produce the delta V during all phases of its mission. While the aeroassisted ARGO (or ASTV for aeroassisted STV) also uses the same engines for the majority of the mission, the final delta V used to insert the ASTV into LEO is produced by skimming the Earth's atmosphere and using the drag on the vehicle to apply the required delta V. This procedure allows for large propellant, and thus cost, savings, but creates many design problems such as the high heating rates and decelerations experienced by a vehicle moving through the atmosphere at hypersonic velocities. The design class, consisting of 43 senior aerospace engineering students, was divided into one managerial and eight technical groups. The technical groups consisted of spacecraft configuration and integration, mission analysis, atmospheric flight, propulsion, power and communications, life support and human factors, logistics and support, and systems analysis. Two committees were set up with members from each group to create the scale models of the STV's and to produce the final report.

Baby-Friendly Practices Minimize Newborn Infants Weight Loss.

Science.gov (United States)

Procaccini, Diane; Curley, Ann L Cupp; Goldman, Martha

2018-04-01

It is accepted that newborns lose weight in the first few days of life. Baby-Friendly practices that support breastfeeding may affect newborn weight loss. The objective of this study were: 1) To determine whether Baby-Friendly practices are associated with term newborn weight loss day 0-2 in three feeding categories (exclusively breastfed, mixed formula fed and breastfed, and formula fed). 2) To determine whether Baby-Friendly practices increase exclusive breast feeding rates in different ethnic populations. This was a retrospective case-control study. Term newborn birth weight, neonatal weights days 0-2, feeding type, type of birth, and demographic information were collected for 1,000 births for the year before Baby-Friendly designation (2010) and 1,000 in 2013 (after designation). Ultimately 683 in the first group and 518 in the second met the inclusion criteria. Mean weight loss decreased day 0-2 for infants in all feeding types after the initiation of Baby-Friendly practices. There was a statistically significant effect of Baby-Friendly designation on weight loss for day 0-2 in exclusively breastfed infants (p Baby-Friendly practices were put in place. There was a decrease in mean weight loss day 0-2 regardless of feeding type after Baby-Friendly designation. Exclusive breast feeding increased in the presence of Baby-Friendly practices.

More Colleges Are Adding Family-Friendly Benefits

Science.gov (United States)

Wilson, Robin

2008-01-01

Results of a new survey of family-friendly benefits by the Center for the Education of Women at the University of Michigan at Ann Arbor show that stopping the tenure clock has become the most common family-friendly benefit in higher education, following paid maternity leave. Other family-friendly policies that top the list in academe allow…

Denotational World-indexed Logical Relations and Friends

DEFF Research Database (Denmark)

Thamsborg, Jacob Junker

and solve the fundamental type-worlds circularity by metric-space theory. This approach scales to state-of-theart step-indexed techniques and permits unrestricted relational reasoning by the use of so-called Bohr relations. Along the way, we develop auxiliary theory; most notably a generalized version...... of separation logic with assertion variables. In particular, we give criteria for when standard, unary separation logic proofs lift to the binary setting. Phrased dierently, given a module-dependent client and a standard separation logic proof of its correctness, we ponder the default question of representation...

Interface for read-out of numerical information to a Shch6800K high-speed printer from an ''Elektronika D3-28'' computer

International Nuclear Information System (INIS)

Taluts, S.G.; IL'inykh, S.A.

1984-01-01

The authors describe an interface to connect a Shch6800K high-speed printer to and Elektronika D3-28 computer. A functional diagram and a line diagram give a detailed illustration of the system. Using series K155 microcircuits, the authors operated the system at a read-out speed of better than 25 16-character lines per second

Archimedeanization of ordered vector spaces

OpenAIRE

Emelyanov, Eduard Yu.

2014-01-01

In the case of an ordered vector space with an order unit, the Archimedeanization method has been developed recently by V.I Paulsen and M. Tomforde. We present a general version of the Archimedeanization which covers arbitrary ordered vector spaces.

Environmentally-friendly practices in hotels

Directory of Open Access Journals (Sweden)

Miriam Mbasera

2016-06-01

Research purpose: To determine the environmentally-friendly practices in hotels in Zimbabwe and South Africa and establish the contribution that hotels are making towards mitigation of the negative environmental effects. Motivation for the study: Currently, the world is facing environmental issues, which include global climate change, ozone depletion, pollution, high consumption of resources and increasing amounts of solid waste. Hotels, as part of the tourism industry, exert a significant impact on the environment. While the extent and range of the impact that hotels exert on the environment suggest an urgent need to address this problem, the question that arises is whether hoteliers appreciate the need for environmentally-friendly initiatives in their establishments. Research design, approach and method: A qualitative research was carried out in eight hotels that employ the strategy of the case study in the aforementioned countries. Main findings: Currently, no policies for green management exist, although some hotels do engage in some environmentally-friendly practices. Some hotel managers do not implement green management initiatives to mitigate the environmental problems emanating from their hotel operations. Practical and/or managerial implications: This indicates that a gap exists between managers’ awareness of appropriate environmentally-friendly practices for hotels, implying a need for training and increased awareness of green management. Contribution and/or value-add: The results could guide managers in the implementation of environmentally-friendly practices in an effort to mitigate environmental problems facing the present generation.

Development of a Three-dimensional Surgical Navigation System with Magnetic Resonance Angiography and a Three-dimensional Printer for Robot-assisted Radical Prostatectomy.

Science.gov (United States)

Jomoto, Wataru; Tanooka, Masao; Doi, Hiroshi; Kikuchi, Keisuke; Mitsuie, Chiemi; Yamada, Yusuke; Suzuki, Toru; Yamano, Toshiko; Ishikura, Reiichi; Kotoura, Noriko; Yamamoto, Shingo

2018-01-02

We sought to develop a surgical navigation system using magnetic resonance angiography (MRA) and a three-dimensional (3D) printer for robot-assisted radical prostatectomy (RARP). Six patients with pathologically proven localized prostate cancer were prospectively enrolled in this study. Prostate magnetic resonance imaging (MRI), consisting of T2-weighted sampling perfection with application-optimized contrasts using different flip-angle evolutions (SPACE) and true fast imaging with steady-state precession (true FISP), reconstructed by volume rendering, was followed by dynamic contrast-enhanced MRA performed with a volumetric interpolated breath-hold examination (VIBE) during intravenous bolus injection of gadobutrol. Images of arterial and venous phases were acquired over approximately 210 seconds. Selected images were sent to a workstation for generation of 3D volume-rendered images and standard triangulated language (STL) files for 3D print construction. The neurovascular bundles (NVBs) were found in sequence on non-contrast images. Accessory pudendal arteries (APAs) were found in all cases in the arterial phase of contrast enhancement but were ill-defined on non-contrast enhanced MRA. Dynamic contrast-enhanced MRA helped to detect APAs, suggesting that this 3D system using MRI will be useful in RARP.

MOSCOW PRINTERS-FOREIGNERS IN THE LAST THIRD OF THE 19TH - EARLY 20TH CENTURY

Directory of Open Access Journals (Sweden)

Г В Аксенова

2017-12-01

Full Text Available The article considers the role of foreigners in the publishing business of Moscow in the last third of the 19th - early 20th century on the example of Moscow printers E.-C. A. Lissner and A.A. Levenson, whose ancestors came to Russia from Austria and Germany. The historio-graphical review showed that the history of Moscow publishing houses and foreign printers who arrived in Russia remains beyond the scope of the current scientifi c interest. There are analyzed the stages of the development of the publishing business, it features, printing fi ndings, the specifi cs of the book market.E.-C. A. Lissner and A.A. Levenson are the brightest fi gures in Russia in the fi eld of publishing. Starting from scratch, they were able to create unique typography, in which it was possible to produce multicolour hard products, phototype table, to improve engraving, chromolithography and colour photozincography. To perform these works, they attracted specialists who were able to develop and implement new ways of printing. E.-C. A. Lissner and A.A. Levenson collaborated with the best artists of Russia helping to implement the ideas of publishing quality printed products that contributed to the aesthetic education of readers. The article reveals the importance of the activities of the two publishers of German origin E.-C. A. Lissner and A. Levenson in the development of the Russian culture (literature and art and the popularization of scientifi c knowledge. They laid new principles of publishing and printing of illustrations, created a new trend in book production. Their activities contributed to the opening of new names in literature and art, promotion of Russian printing technology and book production to both domestic and foreign markets, development of book art and improve-ment of printing.

A Quantum Version of Wigner's Transition State Theory

NARCIS (Netherlands)

Schubert, R.; Waalkens, H.; Wiggins, S.

A quantum version of a recent realization of Wigner's transition state theory in phase space is presented. The theory developed builds on a quantum normal form which locally decouples the quantum dynamics near the transition state to any desired order in (h) over bar. This leads to an explicit

Release Properties and Electrochemical Characterization of Encapsulated Corrosion Inhibitors for Environmentally Friendly Smart Coatings

Science.gov (United States)

Pearman, B. P.; Calle, L. M.; Zhang, X.; Li, W.; Buhrow, J. W.; Johnsey, M. N.; Montgomery, E. L.; Fitzpatrick, L.; Surma, J. M.

2015-01-01

The NASA Kennedy Space Center's Corrosion Technology Lab at the Kennedy Space Center in Florida, U.S.A. has been developing multifunctional smart coatings based on the microencapsulation of environmentally friendly corrosion indicators, inhibitors and self-healing agents. This allows for the incorporation of autonomous corrosion control functionalities, such as corrosion detection and inhibition as well as the self-healing of mechanical damage, into coatings. This paper presents technical details on the characterization of inhibitor-containing particles and their corrosion inhibitive effects using electrochemical and mass loss methods. Three organic environmentally friendly corrosion inhibitors were encapsulated in organic microparticles that are compatible with desired coatings. The total inhibitor content and the release of one of the inhibitors from the microparticles in basic solution was measured. Particles with inhibitor contents of up 60 wt% were synthesized. Fast release, for immediate corrosion protection, as well as long-term release for continued protection, was observed. The inhibition efficacy of the inhibitors, both as the pure materials and in microparticles, on carbon steel was evaluated. Polarization curves and mass loss measurements showed that, in the case of 2MBT, its corrosion inhibition effectiveness was greater when it was delivered from microparticles.

Speech Acts During Friends' and Non-friends' Spontaneous Conversations in Preschool Dyads with High-Functioning Autism Spectrum Disorder versus Typical Development.

Science.gov (United States)

Bauminger-Zviely, Nirit; Golan-Itshaky, Adi; Tubul-Lavy, Gila

2017-05-01

In this study, we videotaped two 10-min. free-play interactions and coded speech acts (SAs) in peer talk of 51 preschoolers (21 ASD, 30 typical), interacting with friend versus non-friend partners. Groups were matched for maternal education, IQ (verbal/nonverbal), and CA. We compared SAs by group (ASD/typical), by partner's friendship status (friend/non-friend), and by partner's disability status. Main results yielded a higher amount and diversity of SAs in the typical than the ASD group (mainly in assertive acts, organizational devices, object-dubbing, and pretend-play); yet, those categories, among others, showed better performance with friends versus non-friends. Overall, a more nuanced perception of the pragmatic deficit in ASD should be adopted, highlighting friendship as an important context for children's development of SAs.

Para-mixed linear spaces

Directory of Open Access Journals (Sweden)

Crasmareanu Mircea

2017-12-01

Full Text Available We consider the paracomplex version of the notion of mixed linear spaces introduced by M. Jurchescu in [4] by replacing the complex unit i with the paracomplex unit j, j2 = 1. The linear algebra of these spaces is studied with a special view towards their morphisms.

Nordic Analysis of Climate Friendly Buildings

DEFF Research Database (Denmark)

Andresen, Inger; Thomsen, Kirsten Engelund; Wahlstrøm, Åsa

This report summarizes the findings of the work conducted within the project “Nordic Analysis of Climate Friendly Buildings”, financed by the Nordic Council of Ministers. The main goal of the project was to establish a knowledge and decision base for a Nordic innovation program that will promote...... the development and demonstration of low energy and climate friendly buildings. The innovation program should support a development that brings the Nordic countries to an international forefront with respect to business strongholds and market penetration of low energy and climate friendly buildings....

Molecular contamination math model support

Science.gov (United States)

Wells, R.

1983-01-01

The operation and features of a preprocessor for the Shuttle/Payload Contamination Evaluation Program Version 2) are described. A preliminary preprocessor for SPACE 2 is developed. Further refinements and enhancements of the preprocessor to insure complete user friendly operation, are recommended.

Development of EASYQAD version β. A visualization code system for gamma and neutron shielding calculations

International Nuclear Information System (INIS)

Kim, Jae Cheon; Kim, Soon Young; Lee, Hwan Soo; Ha, Pham Nhu Viet; Kim, Jong Kyung

2008-01-01

EASYQAD version β was developed by MATLAB GUI (Graphical User Interface) as a visualization code system based on QAD-CGGP-A point-kernel code for convenient shielding calculations of gammas and neutrons. It consists of four graphic interface modules including GEOMETRY, INPUT, OUTPUT, and SHIELD. These modules were compiled in C++ programming language by using the MATLAB Compiler Toolbox to form a stand-along code system that can be run on the Windows XP operating system without MATLAB installation. In addition, EASYQAD version β has user-friendly graphical interfaces and, additionally, many useful functions in comparison with QAD- CGGP-A such as common material library, line and grid detectors, and multi-group energy calculations so as to increase its applicability in the field of radiation shielding analysis. It is a powerful tool for non-experts to analyze easily the shielding problems without special training. Therefore, EASYOAD version β is expected to contribute effectively to the development of radiation shielding analysis by providing users in medical and industrial fields with an efficient radiation shielding code. (author)

Characterization of solid UV curable 3D printer resins for biological applications

KAUST Repository

Sivashankar, Shilpa

2016-12-19

In this paper, we report a simple method to evaluate biocompatibility of solid UV cross-linked resin as a material for microfluidic devices that can be used for biological applications. We evaluated the biocompatibility of the material in two different ways (1) determining if the UV cured resin inhibits the polymerase chain reaction (PCR) and (2) observing agglutination complex formed on the surface of the UV cured resin when anti-CRP antibodies and C- reactive protein (CRP) proteins were allowed to agglutinate. Six different types of 3D printer resins were compared to test the biocompatibility. The study showed that only few among them could be used for fabrication of micro channels and that had least effect on biological molecules that could be used for PCR and protein interactions. Through these studies it is possible to estimate the curing time of various resin and their type of interaction with biomolecules. This study finds importance in on-chip tissue engineering and organ-on-chip applications.

Bioprinting of three dimensional tumor models: a preliminary study using a low cost 3D printer

Directory of Open Access Journals (Sweden)

Polley Christian

2017-09-01

Full Text Available The deep understanding of cancer and tumor genesis, as well as the development of new therapy strategies still remains one of the emerging challenges in modern medicine. To meet these challenges it seems to be absolutely necessary to overcome the drawbacks of the established 2D in vitro models. Especially the missing microenvironment of the tumor, which means the absence of stroma and immune cells, results in a missing cell-cell and cell-stroma interaction as well as disrupted functional communication pathways. Modern 3D culture systems and 3D printing or rather bioprinting technologies attempt to solve this issue and aim to closely mimic natural tumor microenvironment. In this preliminary work we are going to present the first steps of establishing an artificial 3D tumor model utilising a low cost 3D printer. Therefore the printer had been modified with an open-source syringe pump to become a functional bioprinter using viscosity modulated alginate hydrogel. In the first attempts L929 mouse fibroblasts, which are an integral component of natural stroma, had been incorporated into the hydrogel matrix and printed into scaffolds. Subsequent to the printing process the scaffolds got ionically crosslinked with a 5% w/v aqueous solution of CaCl2 to become mechanically stable. After three days of cultivation viability testing had been performed by utilising FDG staining and PET CT to obtain a volumetric viability measurement. The viability imaging showed vital cells homogeneously distributed in the scaffold and therefore stands as an evidence for a working low cost bioprinting process and a successful first step for the development of an artificial 3D tumor model.

Study on 3D printer production of auxiliary device for upper limb for medical imaging test

Energy Technology Data Exchange (ETDEWEB)

Kim, Hyeong Gyun [Dept. of Radiological Science, Far East University, Eumsung (Korea, Republic of); Yoon, Jae Ho [Jukwang Precision Co., Ltd., Gumi (Korea, Republic of); Choi, Seong Dae [Dept. of Mechanical system engineering, Kumoh Institute of Technology, Gumi (Korea, Republic of)

2015-12-15

There is a progressive development in the medical imaging technology, especially of descriptive capability for anatomical structure of human body thanks to advancement of information technology and medical devices. But however maintenance of correct posture is essential for the medical imaging checkup on the shoulder joint requiring rotation of the upper limb due to the complexity of human body. In the cases of MRI examination, long duration and fixed posture are critical, as failure to comply with them leads to minimal possibility of reproducibility only with the efforts of the examiner and will of the patient. Thus, this study aimed to develop an auxiliary device that enables rotation of the upper limb as well as fixing it at quantitative angles for medical imaging examination capable of providing diagnostic values. An auxiliary device has been developed based on the results of precedent studies, by designing a 3D model with the CATIA software, an engineering application, and producing it with the 3D printer. The printer is Objet350 Connex from Stratasys, and acrylonitrile- butadiene-styrene(ABS) is used as the material of the device. Dimensions are 120 X 150 X 190 mm, with the inner diameter of the handle being 125.9 mm. The auxiliary device has 4 components including the body (outside), handle (inside), fixture terminal and the connection part. The body and handle have the gap of 2.1 mm for smooth rotation, while the 360 degree of scales have been etched on the handle so that the angle required for observation may be recorded per patient for traceability and dual examination.

Study on 3D printer production of auxiliary device for upper limb for medical imaging test

International Nuclear Information System (INIS)

Kim, Hyeong Gyun; Yoon, Jae Ho; Choi, Seong Dae

2015-01-01

There is a progressive development in the medical imaging technology, especially of descriptive capability for anatomical structure of human body thanks to advancement of information technology and medical devices. But however maintenance of correct posture is essential for the medical imaging checkup on the shoulder joint requiring rotation of the upper limb due to the complexity of human body. In the cases of MRI examination, long duration and fixed posture are critical, as failure to comply with them leads to minimal possibility of reproducibility only with the efforts of the examiner and will of the patient. Thus, this study aimed to develop an auxiliary device that enables rotation of the upper limb as well as fixing it at quantitative angles for medical imaging examination capable of providing diagnostic values. An auxiliary device has been developed based on the results of precedent studies, by designing a 3D model with the CATIA software, an engineering application, and producing it with the 3D printer. The printer is Objet350 Connex from Stratasys, and acrylonitrile- butadiene-styrene(ABS) is used as the material of the device. Dimensions are 120 X 150 X 190 mm, with the inner diameter of the handle being 125.9 mm. The auxiliary device has 4 components including the body (outside), handle (inside), fixture terminal and the connection part. The body and handle have the gap of 2.1 mm for smooth rotation, while the 360 degree of scales have been etched on the handle so that the angle required for observation may be recorded per patient for traceability and dual examination

Screening for synergistic activity of antimicrobial combinations against carbapenem-resistant Enterobacteriaceae using inkjet printer-based technology.

Science.gov (United States)

Brennan-Krohn, Thea; Truelson, Katherine A; Smith, Kenneth P; Kirby, James E

2017-10-01

Synergistic combination antimicrobial therapy may provide new options for treatment of MDR infections. However, comprehensive in vitro synergy data are limited and facile methods to perform synergy testing in a clinically actionable time frame are unavailable. To systematically investigate a broad range of antibiotic combinations for evidence of synergistic activity against a collection of carbapenem-resistant Enterobacteriaceae (CRE) isolates. We made use of an automated method for chequerboard array synergy testing based on inkjet printer technology in the HP D300 digital dispenser to test 56 pairwise antimicrobial combinations of meropenem, aztreonam, cefepime, colistin, gentamicin, levofloxacin, chloramphenicol, fosfomycin, trimethoprim/sulfamethoxazole, minocycline and rifampicin, as well as the double carbapenem combination of meropenem and ertapenem. In a screening procedure, we tested these combinations against four CRE strains and identified nine antibiotic combinations that showed potential clinically relevant synergy. In confirmatory testing using 10 CRE strains, six combinations demonstrated clinically relevant synergy with both antimicrobials at the minimum fractional inhibitory concentration (FICI-MIN) in the susceptible or intermediate range in at least one trial. These included two novel combinations: minocycline plus colistin and minocycline plus meropenem. In 80% of strains at least one combination demonstrated clinically relevant synergy, but the combinations that demonstrated synergy varied from strain to strain. This work establishes the foundation for future systematic, broad-range investigations into antibiotic synergy for CRE, emphasizes the need for individualized synergy testing and demonstrates the utility of inkjet printer-based technology for the performance of automated antimicrobial synergy assays. © The Author 2017. Published by Oxford University Press on behalf of the British Society for Antimicrobial Chemotherapy. All rights

Direct Write Printing on Thin and Flexible Substrates for Space Applications

Science.gov (United States)

Paquette, Beth

2016-01-01

This presentation describes the work done on direct-write printing conductive traces for a flexible detector application. A Repeatability Plan was established to define detector requirements, material and printer selections, printing facilities, and tests to verify requirements are met. Designs were created for the detector, and printed using an aerosol jet printer. Testing for requirement verification is ongoing.

Relap4/SAS/Mod5 - A version of Relap4/Mod 5 adapted to IPEN/CNEN - SP computer center

International Nuclear Information System (INIS)

Sabundjian, G.

1988-04-01

In order to improve the safety of nuclear reactor power plants several computer codes have been developed in the area of thermal - hydraulics accident analysis. Among the public-available codes, RELAP4, developed by Aerojet Nuclear Company, has been the most popular one. RELAP4 has produced satisfactory results when compared to most of the available experimental data. The purposes of the present work are: optimization of RELAP4 output and messages by writing there information in temporary records, - display of RELAP4 results in graphical form through the printer. The sample problem consists on a simplified model of a 150 MW (e) PWR whose primary circuit is simulated by 6 volumes, 8 junctions and 1 heat slab. This new version of RELAP4 (named RELAP4/SAS/MOD5) have produced results which show that the above mentioned purposes have been reached. Obviously the graphical output by RELAP4/SAS/MOD5 favors the interpretation of results by the user. (author) [pt

Global Rural-Urban Mapping Project, Version 1 (GRUMPv1): Coastlines

Data.gov (United States)

National Aeronautics and Space Administration — The Global Rural-Urban Mapping Project, Version 1 (GRUMPv1) consists of estimates of human population for the years 1990, 1995, and 2000 by 30 arc-second (1km) grid...

Influence of friends on children's physical activity: a review.

Science.gov (United States)

Maturo, Claire C; Cunningham, Solveig A

2013-07-01

We examined evidence for friendship influences on children's physical activity (PA) through systematic searches of online databases in May 2012. We identified 106 studies (25 qualitative) published in English since 2000 that analyzed indicators of friendship influences (e.g., communication about PA, friends' PA, and PA with friends) among persons younger than 19 years. Children's PA was positively associated with encouragement from friends (43 of 55 studies indicating a positive relationship), friends' own PA (30/35), and engagement with friends in PA (9/10). These findings are consistent with friends influencing PA, but most studies did not isolate influence from other factors that could explain similarity. Understanding friendship influences in childhood can facilitate the promotion of lifelong healthy habits. PA with friends should be considered in health promotion programs.

Moving toward rapid and low-cost point-of-care molecular diagnostics with a repurposed 3D printer and RPA.

Science.gov (United States)

Chan, Kamfai; Wong, Pui-Yan; Parikh, Chaitanya; Wong, Season

2018-03-15

Traditionally, the majority of nucleic acid amplification-based molecular diagnostic tests are done in centralized settings. In recent years, point-of-care tests have been developed for use in low-resource settings away from central laboratories. While most experts agree that point-of-care molecular tests are greatly needed, their availability as cost-effective and easy-to-operate tests remains an unmet goal. In this article, we discuss our efforts to develop a recombinase polymerase amplification reaction-based test that will meet these criteria. First, we describe our efforts in repurposing a low-cost 3D printer as a platform that can carry out medium-throughput, rapid, and high-performing nucleic acid extraction. Next, we address how these purified templates can be rapidly amplified and analyzed using the 3D printer's heated bed or the deconstructed, low-cost thermal cycler we have developed. In both approaches, real-time isothermal amplification and detection of template DNA or RNA can be accomplished using a low-cost portable detector or smartphone camera. Last, we demonstrate the capability of our technologies using foodborne pathogens and the Zika virus. Our low-cost approach does not employ complicated and high-cost components, making it suitable for resource-limited settings. When integrated and commercialized, it will offer simple sample-to-answer molecular diagnostics. Copyright © 2018 Elsevier Inc. All rights reserved.

3D printing for dummies

CERN Document Server

Hausman, Kalani Kirk

2014-01-01

Get started printing out 3D objects quickly and inexpensively! 3D printing is no longer just a figment of your imagination. This remarkable technology is coming to the masses with the growing availability of 3D printers. 3D printers create 3-dimensional layered models and they allow users to create prototypes that use multiple materials and colors.  This friendly-but-straightforward guide examines each type of 3D printing technology available today and gives artists, entrepreneurs, engineers, and hobbyists insight into the amazing things 3D printing has to offer. You'll discover methods for

Investigation of the Effect of Training on Promoting Breast-feeding at Baby-Friendly Hospital Case Study; Tohid Hospital in Jam, Bushehr

Directory of Open Access Journals (Sweden)

Azam Nickkhaha

2015-06-01

Full Text Available Background: The Baby-Friendly Hospital Initiative was launched in 1989 by World Health Organization and the United Nations Children's Fund for the promotion of breastfeeding. This program was implemented in many departments of gynecology and obstetrics and resulted in reduced malnutrition, infection, morbidity and mortality in children. This program has introduced 10 specific steps to support successful breastfeeding. For instance, in the fourth step, skin-to-skin contact and breastfeeding are promoted since the time of birth, and in the fifth step, mothers are instructed on how to breastfeed or persist in breastfeeding. In these ten steps, mothers are trained in various fields. Methods: In this cross-sectional study, a standardized questionnaire was used to collect data at baby-friendly hospitals. To assess the difference between multiple nominal variables, variance analysis was performed, using SPSS version 17. Results: Based on the analysis, mothers' awareness of the benefits of breast milk and breastfeeding was 83% in a baby-friendly hospital. Also, their awareness of proper breastfeeding was estimated at 78.5%. In addition, mothers' knowledge about the frequency of breastfeeding was 70%. Conclusion: Given the role of Baby-Friendly Hospital Initiative in training mothers on the importance of breastfeeding and its persistence in future, careful monitoring of these hospitals, breastfeeding support services and breastfeeding training by midwives at healthcare centers are of great importance.

Total body irradiation with a compensator fabricated using a 3D optical scanner and a 3D printer.

Science.gov (United States)

Park, So-Yeon; Kim, Jung-In; Joo, Yoon Ha; Lee, Jung Chan; Park, Jong Min

2017-05-07

We propose bilateral total body irradiation (TBI) utilizing a 3D printer and a 3D optical scanner. We acquired surface information of an anthropomorphic phantom with the 3D scanner and fabricated the 3D compensator with the 3D printer, which could continuously compensate for the lateral missing tissue of an entire body from the beam's eye view. To test the system's performance, we measured doses with optically stimulated luminescent dosimeters (OSLDs) as well as EBT3 films with the anthropomorphic phantom during TBI without a compensator, conventional bilateral TBI, and TBI with the 3D compensator (3D TBI). The 3D TBI showed the most uniform dose delivery to the phantom. From the OSLD measurements of the 3D TBI, the deviations between the measured doses and the prescription dose ranged from  -6.7% to 2.4% inside the phantom and from  -2.3% to 0.6% on the phantom's surface. From the EBT3 film measurements, the prescription dose could be delivered to the entire body of the phantom within  ±10% accuracy, except for the chest region, where tissue heterogeneity is extreme. The 3D TBI doses were much more uniform than those of the other irradiation techniques, especially in the anterior-to-posterior direction. The 3D TBI was advantageous, owing to its uniform dose delivery as well as its efficient treatment procedure.

Child- and elder-friendly urban public places in Fatahillah Square Historical District

Science.gov (United States)

Srinaga, F.; LKatoppo, M.; Hidayat, J.

2018-03-01

Fatahillah square as an important historical urban square in Jakarta has problems in eye level area integrative processing. Visitors cannot enjoy their time while in the square regarding their visuals, feelings, space, and bodies comfort. These also lead to other problems in which the square is lack of friendly and convenient places for children, the elderly and also the disabled, especially people with limited moving space. The research will attempt in proposing design inception for the Fatahillah Square that is using inclusive user-centered design approach, while in the same time incorporate theoretical studies of children and elderly-design considerations. The first stage of this research was building inclusive design parameter; begin with a context-led research which assesses the quality of Fatahillah square through three basic components of urban space: hardware, software and orgware. The second stage of this research is to propose inclusive design inception for the Fatahillah square.

Efficient Mosaicking of Spitzer Space Telescope Images

Science.gov (United States)

Jacob, Joseph; Makovoz, David; Eisenhardt, Peter

2007-01-01

A parallel version of the MOPEX software, which generates mosaics of infrared astronomical images acquired by the Spitzer Space Telescope, extends the capabilities of the prior serial version. In the parallel version, both the input image space and the output mosaic space are divided among the available parallel processors. This is the only software that performs the point-source detection and the rejection of spurious imaging effects of cosmic rays required by Spitzer scientists. This software includes components that implement outlier-detection algorithms that can be fine-tuned for a particular set of image data by use of a number of adjustable parameters. This software has been used to construct a mosaic of the Spitzer Infrared Array Camera Shallow Survey, which comprises more than 17,000 exposures in four wavelength bands from 3.6 to 8 m and spans a solid angle of about 9 square degrees. When this software was executed on 32 nodes of the 1,024-processor Cosmos cluster computer at NASA s Jet Propulsion Laboratory, a speedup of 8.3 was achieved over the serial version of MOPEX. The performance is expected to improve dramatically once a true parallel file system is installed on Cosmos.

Parental influences on memories of parents and friends.

Science.gov (United States)

Tani, Franca; Bonechi, Alice; Peterson, Carole; Smorti, Andrea

2010-01-01

The authors evaluated the role parent-child relationship quality has on two types of memories, those of parents and those of friends. Participants were 198 Italian university students who recalled memories during 4 separate timed memory-fluency tasks about their preschool, elementary school, middle school, high school and university years. Half were instructed to recall memories involving parents and the remainder memories involving friends. Moreover, parent-child relationships were assessed by the Network of Relationships Inventory (NRI; W. Furman & D. Buhrmester, 1985) and Adolescents' Report of Parental Monitoring (D. M. Capaldi & G. R. Patterson, 1989). Results showed that men with positive parent-son relationships had more memories of parents and more affectively positive memories of friends, supporting a consistency model positing similarity between parent-child relationships and memories of friends. Women with positive parental relationship quality had more affectively positive memories of parents but for friends, positive relationship quality only predicted positive memories when young. At older ages, especially middle school-aged children, negative parent-daughter relationships predicted more positive memories of friends, supporting a compensatory model. The gender of parent also mattered, with fathers having a more influential role on affect for memories of friends.

Eco friendly expectations and limitations in daycare

DEFF Research Database (Denmark)

Husted, Mia

This presentation elaborates on expectations and limitations of eco-friendly pedagogical responses to the sustainability crisis. The pedagogical perspectives on eco-friendly responses originates from an action research project involving pedagogues in day care centers and teachers at a University ...... College in Denmark. As part of the project they were asked to explore, elaborate and develop new pedagogical actions and perspectives related to future relationships between human beings and our common nature......This presentation elaborates on expectations and limitations of eco-friendly pedagogical responses to the sustainability crisis. The pedagogical perspectives on eco-friendly responses originates from an action research project involving pedagogues in day care centers and teachers at a University...

Fermilab Friends for Science Education | Programs

Science.gov (United States)

Fermilab Friends for Science Education FFSE Home About Us Join Us Support Us Contact Us Programs Donors Board of Directors Board Tools Calendar Join Us Donate Now Get FermiGear! Education Office Search photo Fermilab Friends for Science Education, in partnership with Fermilab and area educators, designs

Best friends' discussions of social dilemmas.

Science.gov (United States)

McDonald, Kristina L; Malti, Tina; Killen, Melanie; Rubin, Kenneth H

2014-02-01

Peer relationships, particularly friendships, have been theorized to contribute to how children and adolescents think about social and moral issues. The current study examined how young adolescent best friends (191 dyads; 53.4% female) reason together about multifaceted social dilemmas and how their reasoning is related to friendship quality. Mutually-recognized friendship dyads were videotaped discussing dilemmas entailing moral, social-conventional and prudential/pragmatic issues. Both dyad members completed a self-report measure of friendship quality. Dyadic data analyses guided by the Actor-Partner Interdependence Model indicated that adolescent and friend reports of friendship qualities were related to the forms of reasoning used during discussion. Friends who both reported that they could resolve conflicts in a constructive way were more likely to use moral reasoning than friends who reported that their conflict resolution was poor or disagreed on the quality of their conflict resolution. The findings provide evidence for the important role that friendship interaction may play in adolescents' social and moral development.

Synchronizing the city with human-based spaces

Science.gov (United States)

Gyergyák, János

2018-03-01

The paper is about to summarize the most important development tools to make the urban spaces more human friendly in Denver, Colorado. There are more needs for having more livable and sustainable areas by reducing the use of automobiles and focusing on multimodal street design. The strategies are the basic elements to make our urban spaces better and happier from The United States to Hungary

Auditing Consistency and Usefulness of LOINC Use among Three Large Institutions - Using Version Spaces for Grouping LOINC Codes

Science.gov (United States)

Lin, M.C.; Vreeman, D.J.; Huff, S.M.

2012-01-01

Objectives We wanted to develop a method for evaluating the consistency and usefulness of LOINC code use across different institutions, and to evaluate the degree of interoperability that can be attained when using LOINC codes for laboratory data exchange. Our specific goals were to: 1) Determine if any contradictory knowledge exists in LOINC. 2) Determine how many LOINC codes were used in a truly interoperable fashion between systems. 3) Provide suggestions for improving the semantic interoperability of LOINC. Methods We collected Extensional Definitions (EDs) of LOINC usage from three institutions. The version space approach was used to divide LOINC codes into small sets, which made auditing of LOINC use across the institutions feasible. We then compared pairings of LOINC codes from the three institutions for consistency and usefulness. Results The number of LOINC codes evaluated were 1,917, 1,267 and 1,693 as obtained from ARUP, Intermountain and Regenstrief respectively. There were 2,022, 2,030, and 2,301 version spaces among ARUP & Intermountain, Intermountain & Regenstrief and ARUP & Regenstrief respectively. Using the EDs as the gold standard, there were 104, 109 and 112 pairs containing contradictory knowledge and there were 1,165, 765 and 1,121 semantically interoperable pairs. The interoperable pairs were classified into three levels: 1) Level I – No loss of meaning, complete information was exchanged by identical codes. 2) Level II – No loss of meaning, but processing of data was needed to make the data completely comparable. 3) Level III – Some loss of meaning. For example, tests with a specific ‘method’ could be rolled-up with tests that were ‘methodless’. Conclusions There are variations in the way LOINC is used for data exchange that result in some data not being truly interoperable across different enterprises. To improve its semantic interoperability, we need to detect and correct any contradictory knowledge within LOINC and add

Introduction to benchmark dose methods and U.S. EPA's benchmark dose software (BMDS) version 2.1.1

International Nuclear Information System (INIS)

Davis, J. Allen; Gift, Jeffrey S.; Zhao, Q. Jay

2011-01-01

Traditionally, the No-Observed-Adverse-Effect-Level (NOAEL) approach has been used to determine the point of departure (POD) from animal toxicology data for use in human health risk assessments. However, this approach is subject to substantial limitations that have been well defined, such as strict dependence on the dose selection, dose spacing, and sample size of the study from which the critical effect has been identified. Also, the NOAEL approach fails to take into consideration the shape of the dose-response curve and other related information. The benchmark dose (BMD) method, originally proposed as an alternative to the NOAEL methodology in the 1980s, addresses many of the limitations of the NOAEL method. It is less dependent on dose selection and spacing, and it takes into account the shape of the dose-response curve. In addition, the estimation of a BMD 95% lower bound confidence limit (BMDL) results in a POD that appropriately accounts for study quality (i.e., sample size). With the recent advent of user-friendly BMD software programs, including the U.S. Environmental Protection Agency's (U.S. EPA) Benchmark Dose Software (BMDS), BMD has become the method of choice for many health organizations world-wide. This paper discusses the BMD methods and corresponding software (i.e., BMDS version 2.1.1) that have been developed by the U.S. EPA, and includes a comparison with recently released European Food Safety Authority (EFSA) BMD guidance.

How Can I Help a Friend Who Cuts?

Science.gov (United States)

... Safe Videos for Educators Search English Español How Can I Help a Friend Who Cuts? KidsHealth / For Teens / How Can I Help a Friend Who Cuts? What's in ... them? If so, what should you do? It can be hard to understand why a friend might ...

CENTURY: Modeling Ecosystem Responses to Climate Change, Version 4 (VEMAP 1995)

Data.gov (United States)

National Aeronautics and Space Administration — ABSTRACT: The CENTURY model, Version 4, is a general model of plant-soil nutrient cycling that is being used to simulate carbon and nutrient dynamics for different...

Friend suggestion in social network based on user log

Science.gov (United States)

Kaviya, R.; Vanitha, M.; Sumaiya Thaseen, I.; Mangaiyarkarasi, R.

2017-11-01

Simple friend recommendation algorithms such as similarity, popularity and social aspects is the basic requirement to be explored to methodically form high-performance social friend recommendation. Suggestion of friends is followed. No tags of character were followed. In the proposed system, we use an algorithm for network correlation-based social friend recommendation (NC-based SFR).It includes user activities like where one lives and works. A new friend recommendation method, based on network correlation, by considering the effect of different social roles. To model the correlation between different networks, we develop a method that aligns these networks through important feature selection. We consider by preserving the network structure for a more better recommendations so that it significantly improves the accuracy for better friend-recommendation.

Ethnic Differences among Friend Networks Later in Life

Science.gov (United States)

Kang, Hyunsook; Hebert, Corie

2014-01-01

This study seeks to broaden the understanding of friend relationships in older adults and the differences in those friend relationships among various ethnic groups. Secondary data from the National Social Life, Health and Aging Project (NSHAP) was analyzed to test the hypothesis that Caucasian older adults have stronger friend networks than older…

Maternal Affection Moderates Friend Influence on Schoolwork Engagement

Science.gov (United States)

Marion, Donna; Laursen, Brett; Kiuru, Noona; Nurmi, Jari-Erik; Salmela-Aro, Katariina

2014-01-01

This study investigated friend influence over adolescent schoolwork engagement in 160 same-sex friend dyads (94 female dyads and 66 male dyads). Participants were approximately 16 years of age at the outset. Each friend described his or her own schoolwork engagement, school burnout, and perceptions of maternal affection. The results revealed that…

Compatibility analysis of 3D printer resin for biological applications

KAUST Repository

Sivashankar, Shilpa

2016-08-30

The salient features of microfluidics such as reduced cost, handling small sample and reagent volumes and less time required to fabricate the devices has inspired the present work. The incompatibility of three-dimensional printer resins in their native form and the method to improve their compatibility to many biological processes via surface modification are reported. The compatibility of the material to build microfluidic devices was evaluated in three different ways: (i) determining if the ultraviolet (UV) cured resin inhibits the polymerase chain reaction (PCR), i.e. testing devices for PCR compatibility; (ii) observing agglutination complex formed on the surface of the UV cured resin when anti-C-reactive protein (CRP) antibodies and CRP proteins were allowed to agglutinate; and (iii) by culturing human embryonic kidney cell line cells and testing for its attachment and viability. It is shown that only a few among four in its native form could be used for fabrication of microchannels and that had the least effect on biological molecules that could be used for PCR and protein interactions and cells, whereas the others were used after treating the surface. Importance in building lab-on-chip/micrototal analysis systems and organ-on-chip devices is found.

CENTURY: Modeling Ecosystem Responses to Climate Change, Version 4 (VEMAP 1995)

Data.gov (United States)

National Aeronautics and Space Administration — The CENTURY model, Version 4, is a general model of plant-soil nutrient cycling that is being used to simulate carbon and nutrient dynamics for different types of...

Characterization of emissions from a desktop 3D printer and indoor air measurements in office settings.

Science.gov (United States)

Steinle, Patrick

2016-01-01

Emissions from a desktop 3D printer based on fused deposition modeling (FDM) technology were measured in a test chamber and indoor air was monitored in office settings. Ultrafine aerosol (UFA) emissions were higher while printing a standard object with polylactic acid (PLA) than with acrylonitrile butadiene styrene (ABS) polymer (2.1 × 10(9) vs. 2.4 × 10(8) particles/min). Prolonged use of the printer led to higher emission rates (factor 2 with PLA and 4 with ABS, measured after seven months of occasional use). UFA consisted mainly of volatile droplets, and some small (100-300 nm diameter) iron containing and soot-like particles were found. Emissions of inhalable and respirable dust were below the limit of detection (LOD) when measured gravimetrically, and only slightly higher than background when measured with an aerosol spectrometer. Emissions of volatile organic compounds (VOC) were in the range of 10 µg/min. Styrene accounted for more than 50% of total VOC emitted when printing with ABS; for PLA, methyl methacrylate (MMA, 37% of TVOC) was detected as the predominant compound. Two polycyclic aromatic hydrocarbons (PAH), fluoranthene and pyrene, were observed in very low amounts. All other analyzed PAH, as well as inorganic gases and metal emissions except iron (Fe) and zinc (Zn), were below the LOD or did not differ from background without printing. A single 3D print (165 min) in a large, well-ventilated office did not significantly increase the UFA and VOC concentrations, whereas these were readily detectable in a small, unventilated room, with UFA concentrations increasing by 2,000 particles/cm(3) and MMA reaching a peak of 21 µg/m(3) and still being detectable in the room even 20 hr after printing.

A Study about Youth and Uses of Public Spaces

Directory of Open Access Journals (Sweden)

Fardin Alikhah

2016-04-01

Full Text Available There has been a huge concern about the manner of confrontations of different social groups with urban public spaces within urban scholars. Among these social groups, young people have been particularly important. Because they have a tangible presence in the city's public spaces and social life of the city are affected by their presence. This paper examines the uses of public spaces by young people and will pay special attention to the role of social control on use of public spaces. Paper focuses on the study of young people who attend in public places with their friends from opposite sex. We have inspired by theories of urban public spaces such as Oldenburg's third place as well as comprehensive research of Rob White on crime, policing and urban public spaces in Australia in this paper. The main question of the paper is that this particular group of young people choose which public spaces and why? In a qualitative approach, two techniques of observation and in - depth interviews have been chosen for collecting data. Original data collected in interviews with 20 girls and boys who attend in public places with their friends from opposite sex. Results show that parks and coffee shops are preferred urban public places of youth. Formal control would push these youth to out of the way and cozy public spaces.

SHABERTH - ANALYSIS OF A SHAFT BEARING SYSTEM (CRAY VERSION)

Science.gov (United States)

Coe, H. H.

1994-01-01

shear forces in the inlet zone of lubricated contacts, which accounts for the degree of lubricant film starvation; modeling normal and friction forces between a ball and a cage pocket, which account for the transition between the hydrodynamic and elastohydrodynamic regimes of lubrication; and a model of the effect on fatigue life of the ratio of the EHD plateau film thickness to the composite surface roughness. SHABERTH is intended to be as general as possible. The models in SHABERTH allow for the complete mathematical simulation of real physical systems. Systems are limited to a maximum of five bearings supporting the shaft, a maximum of thirty rolling elements per bearing, and a maximum of one hundred temperature nodes. The SHABERTH program structure is modular and has been designed to permit refinement and replacement of various component models as the need and opportunities develop. A preprocessor is included in the IBM PC version of SHABERTH to provide a user friendly means of developing SHABERTH models and executing the resulting code. The preprocessor allows the user to create and modify data files with minimal effort and a reduced chance for errors. Data is utilized as it is entered; the preprocessor then decides what additional data is required to complete the model. Only this required information is requested. The preprocessor can accommodate data input for any SHABERTH compatible shaft bearing system model. The system may include ball bearings, roller bearings, and/or tapered roller bearings. SHABERTH is written in FORTRAN 77, and two machine versions are available from COSMIC. The CRAY version (LEW-14860) has a RAM requirement of 176K of 64 bit words. The IBM PC version (MFS-28818) is written for IBM PC series and compatible computers running MS-DOS, and includes a sample MS-DOS executable. For execution, the PC version requires at least 1Mb of RAM and an 80386 or 486 processor machine with an 80x87 math co-processor. The standard distribution medium for the

Global Roads Open Access Data Set, Version 1 (gROADSv1)

Data.gov (United States)

National Aeronautics and Space Administration — The Global Roads Open Access Data Set, Version 1 (gROADSv1) was developed under the auspices of the CODATA Global Roads Data Development Task Group. The data set...

Ladtap XL Version 2017: A Spreadsheet For Estimating Dose Resulting From Aqueous Releases

Energy Technology Data Exchange (ETDEWEB)

Minter, K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Jannik, T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2017-06-15

LADTAP XL© is an EXCEL© spreadsheet used to estimate dose to offsite individuals and populations resulting from routine and accidental releases of radioactive materials to the Savannah River. LADTAP XL© contains two worksheets: LADTAP and IRRIDOSE. The LADTAP worksheet estimates dose for environmental pathways including external exposure resulting from recreational activities on the Savannah River and internal exposure resulting from ingestion of water, fish, and invertebrates originating from the Savannah River. IRRIDOSE estimates offsite dose to individuals and populations from irrigation of foodstuffs with contaminated water from the Savannah River. In 2004, a complete description of the LADTAP XL© code and an associated user’s manual was documented in LADTAP XL©: A Spreadsheet for Estimating Dose Resulting from Aqueous Release (WSRC-TR-2004-00059) and revised input parameters, dose coefficients, and radionuclide decay constants were incorporated into LADTAP XL© Version 2013 (SRNL-STI-2011-00238). LADTAP XL© Version 2017 is a slight modification to Version 2013 with minor changes made for more user-friendly parameter inputs and organization, updates in the time conversion factors used within the dose calculations, and fixed an issue with the expected time build-up parameter referenced within the population shoreline dose calculations. This manual has been produced to update the code description, verification of the models, and provide an updated user’s manual. LADTAP XL© Version 2017 has been verified by Minter (2017) and is ready for use at the Savannah River Site (SRS).

Topological vector spaces and distributions

CERN Document Server

Horvath, John

2012-01-01

""The most readable introduction to the theory of vector spaces available in English and possibly any other language.""-J. L. B. Cooper, MathSciNet ReviewMathematically rigorous but user-friendly, this classic treatise discusses major modern contributions to the field of topological vector spaces. The self-contained treatment includes complete proofs for all necessary results from algebra and topology. Suitable for undergraduate mathematics majors with a background in advanced calculus, this volume will also assist professional mathematicians, physicists, and engineers.The precise exposition o

Adolescent friend similarity on alcohol abuse as a function of participation in romantic relationships: Sometimes a new love comes between old friends.

Science.gov (United States)

DeLay, Dawn; Laursen, Brett; Bukowski, William M; Kerr, Margaret; Stattin, Håkan

2016-01-01

This study tests the hypothesis that adolescents with romantic partners are less similar to their friends on rates of alcohol abuse than adolescents without romantic partners. Participants (662 girls, 574 boys) ranging in age from 12 to 19 years nominated friends and romantic partners, and completed a measure of alcohol abuse. In hierarchical linear models, friends with romantic partners were less similar on rates of alcohol abuse than friends without romantic partners, especially if they were older and less accepted. Follow-up longitudinal analyses were conducted on a subsample (266 boys, 374 girls) of adolescents who reported friendships that were stable across 2 consecutive years. Associations between friend reports of alcohol abuse declined after adolescents became involved in a romantic relationship, to the point at which they became more similar to their romantic partners than to their friends. (PsycINFO Database Record (c) 2015 APA, all rights reserved).

Eco-friendly polymer nanocomposites processing and properties

CERN Document Server

Thakur, Vijay Kumar

2015-01-01

This book contains precisely referenced chapters, emphasizing environment-friendly polymer nanocomposites with basic fundamentals, practicality and alternatives to traditional nanocomposites through detailed reviews of different environmental friendly materials procured from different resources, their synthesis and applications using alternative green approaches. The book aims at explaining basics of eco-friendly polymer nanocomposites from different natural resources and their chemistry along with practical applications which present a future direction in the biomedical, pharmaceutical and automotive industry. The book attempts to present emerging economic and environmentally friendly polymer nanocomposites that are free from side effects studied in the traditional nanocomposites. This book is the outcome of contributions by many experts in the field from different disciplines, with various backgrounds and expertises. This book will appeal to researchers as well as students from different disciplines. The co...

Positrusion Filament Recycling System, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — TUI proposes a novel process to produce 3d printer feedstock filament out of scrap ABS on the ISS. Currently the plastic filament materials that most 3d printers use...

Synchronizing the city with human-based spaces

Directory of Open Access Journals (Sweden)

Gyergyák János

2018-03-01

Full Text Available The paper is about to summarize the most important development tools to make the urban spaces more human friendly in Denver, Colorado. There are more needs for having more livable and sustainable areas by reducing the use of automobiles and focusing on multimodal street design. The strategies are the basic elements to make our urban spaces better and happier from The United States to Hungary

Illustrating Mathematics using 3D Printers

OpenAIRE

Knill, Oliver; Slavkovsky, Elizabeth

2013-01-01

3D printing technology can help to visualize proofs in mathematics. In this document we aim to illustrate how 3D printing can help to visualize concepts and mathematical proofs. As already known to educators in ancient Greece, models allow to bring mathematics closer to the public. The new 3D printing technology makes the realization of such tools more accessible than ever. This is an updated version of a paper included in book Low-Cost 3D Printing for science, education and Sustainable Devel...

Gratitude for help among adult friends and siblings.

Science.gov (United States)

Rotkirch, Anna; Lyons, Minna; David-Barrett, Tamas; Jokela, Markus

2014-07-06

Although gratitude is a key prosocial emotion reinforcing reciprocal altruism, it has been largely ignored in the empirical literature. We examined feelings of gratitude and the importance of reciprocity in same-sex peer relations. Participants were 772 individuals (189 men; mean age = 28.80) who completed an online survey using a vignette design. We investigated (i) differences in reported gratitude and the importance of reciprocity among same-sex siblings and same-sex friends, and (ii) how relationship closeness moderates these associations. Based on the theory of kin altruism, we expect that people would feel more grateful towards friends than towards their siblings, and that lack of gratitude or failure to pay back a loan would bother more with friends than with siblings, irrespective of emotional closeness. Results showed that levels of gratitude and expectations of reciprocity were higher towards friends compared to siblings. This was the case also after controlling for emotional closeness. Being close generally made participants feel more grateful and expect lower displays of gratitude in the other. Closeness was also strongly associated with emotional gratitude among siblings compared to friends. We conclude that feelings and displays of gratitude have a special role in friendships. Although a close sibling may elicit as much gratitude as a friend does, even a very close friend is not exempt from the logic of reciprocity in the same way that a sibling is.

Line printing solution-processable small molecules with uniform surface profile via ink-jet printer.

Science.gov (United States)

Liu, Huimin; Xu, Wei; Tan, Wanyi; Zhu, Xuhui; Wang, Jian; Peng, Junbiao; Cao, Yong

2016-03-01

Line printing offers a feasible approach to remove the pixel well structure which is widely used to confine the ink-jet printed solution. In the study, a uniform line is printed by an ink-jet printer. To achieve a uniform surface profile of the printed line, 10vol% low-volatile solvent DMA (3,4-Dimethylanisole) is mixed with high-volatile solvent Pxy (p-xylene) as the solvent. After a solution-processable small molecule is dissolved, the surface tension of DMA solution becomes lower than that of Pxy solution, which creates an inward Marangoni flow during the solvent evaporation. The inward Marangoni flow balances out the outward capillary flow, thereby forming a flat film surface. The line width of the printed line depends on the contact angle of the solution on the hole injection layer. Copyright © 2015 Elsevier Inc. All rights reserved.

Engineering graphics data entry for space station data base

Science.gov (United States)

Lacovara, R. C.

1986-01-01

The entry of graphical engineering data into the Space Station Data Base was examined. Discussed were: representation of graphics objects; representation of connectivity data; graphics capture hardware; graphics display hardware; site-wide distribution of graphics, and consolidation of tools and hardware. A fundamental assumption was that existing equipment such as IBM based graphics capture software and VAX networked facilities would be exploited. Defensible conclusions reached after study and simulations of use of these systems at the engineering level are: (1) existing IBM based graphics capture software is an adequate and economical means of entry of schematic and block diagram data for present and anticipated electronic systems for Space Station; (2) connectivity data from the aforementioned system may be incorporated into the envisioned Space Station Data Base with modest effort; (3) graphics and connectivity data captured on the IBM based system may be exported to the VAX network in a simple and direct fashion; (4) graphics data may be displayed site-wide on VT-125 terminals and lookalikes; (5) graphics hard-copy may be produced site-wide on various dot-matrix printers; and (6) the system may provide integrated engineering services at both the engineering and engineering management level.

A Quantum Version of Wigner’s Transition State Theory

NARCIS (Netherlands)

Schubert, R.; Waalkens, H.; Wiggins, S.

2009-01-01

A quantum version of a recent realization of Wigner’s transition state theory in phase space is presented. The theory developed builds on a quantum normal form which locally decouples the quantum dynamics near the transition state to any desired order in ħ. This leads to an explicit algorithm to

Space Station - Opportunity for international cooperation and utilization

Science.gov (United States)

Pedersen, K. S.

1984-01-01

In connection with his announcement regarding the development of a permanently manned Space Station, President Reagan invited the United States' friends and allies to join in the Space Station program. The President's invitation was preceded by more than two years of interaction between NASA and some of its potential partners in Space Station planning activities. Attention is given to international participation in Space Station planning, international cooperation on the Space Station, the guidelines for international cooperation, and the key challenges. Questions regarding quid pro quos are considered along with aspects of technology transfer, commercial use, problems of management, and the next steps concerning the Space Station program.

[Reconstruction assisted by 3D printing in maxillofacial surgery].

Science.gov (United States)

Ernoult, C; Bouletreau, P; Meyer, C; Aubry, S; Breton, P; Bachelet, J-T

2015-04-01

3-dimensional models (3D) appeared in the medical field 20 years ago. The recent development of consumer 3D printers explains the renewed interest in this technology. We describe the technical and practical modalities of this surgical tool, illustrated by concrete examples. The OsiriX(®) software (version 5.8.5, Geneva, Switzerland) was used for 3D surface reconstruction of the area of interest, the generation and export of ".stl" file. The NetFabb(®) software (Basic version 5.1.1, Lupburg, Germany) provided the preparation of ".stl" file. The 3D-printer was an Up plus 2 Easy 120(®) (PP3DP, Beijing Technology Co. TierTime Ltd., Chine). The printer used fused deposition modeling. The softwar Up!(®) allowed the 3d impression as required. The first case illustrated the value of 3D printing in the upper (frontal sinus and orbital roof). The second case concerned the preconfiguration of the osteosynthesis material for a complex fracture of the midface through the "mirroring" system. The third case showed the conformation of a prereconstruction for segmental mandibulectomy. Current 3D-printers are easy to use and represent a promising solution for medical prototyping. The 3D printing will quickly become undeniable because of its advantages: information sharing, simulation, surgical guides, pedagogy. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

PRODUCTION WITH 3D PRINTERS IN TEXTILES [REVIEW

Directory of Open Access Journals (Sweden)

KESKIN Reyhan

2015-05-01

Full Text Available 3D printers are gaining more attention, finding different applications and 3D printing is being regarded as a ‘revolution’ of the 2010s for production. 3D printing is a production method that produces 3-dimensional objects by combining very thin layers over and over to form the object using 3D scanners or via softwares either private or open source. 3D printed materials find application in a large range of fields including aerospace, automotive, medicine and material science. There are several 3D printing methods such as fused deposition modeling (FDM, stereolithographic apparatus (SLA, selective laser sintering (SLS, inkjet 3D printing and laminated object manufacturing (LOM. 3D printing process involves three steps: production of the 3D model file, conversion of the 3D model file into G-code and printing the object. 3D printing finds a large variety of applications in many fields; however, textile applications of 3D printing remain rare. There are several textile-like 3D printed products mostly for use in fashion design, for research purposes, for technical textile applications and for substituting traditional textiles suchas weft-knitted structures and lace patterns. 3D printed textile-like structures are not strong enough for textile applications as they tend to break easily and although they have the drape of a textile material, they still lack the flexibility of textiles. 3D printing technology has to gain improvement to produce materials that will be an equivalent for textile materials, and has to be a faster method to compete with traditional textile production methods.

WE-DE-201-09: Performance of HDR Ring Surface Applicator Printed by 3D Printer

International Nuclear Information System (INIS)

Xu, Z; Baker, J; Hsia, A; Ryu, S

2016-01-01

Purpose: The commercially available Leipzig-style Cone for High Dose Rate (HDR) Brachytherapy has a steep depth dose curve and a non-uniform dose distribution. This work shows the performance of a Ring Surface Applicator created using a 3D printer that can generate a better dose distribution. Calculated doses were verified with film measurement. Methods: The water equivalent red-ABS plastic was used to print the Ring Surface Applicator which hosts three catheters: a center piece with a straight catheter and two concentric rings with diameters of 3.5 and 5.5 cm. Gafchromic EBT2 film, Epson Expression 10000 flatbed scanner, and the online software at radiochromic.com were used to analyze the measured data. 10cm×10cm piece of film was sandwiched between two 15×10×5cm3 polystyrene phantoms. The applicator was positioned directly on top of the phantom. Measurement was done using dwell time and positions calculated by Eclipse BrachyVision treatment planning system (RTP). Results: Depth dose curve was generated from the plan and measurement. The results show that the measured and calculated depth dose were in agreement (<3%) from surface to 4mm depth. A discrepancy of 6% was observed at 5 mm depth, where the dose is typically prescribed to. For depths deeper than 5 mm, the measured doses were lower than those calculated by Eclipse BrachyVision. This can be attributed to a combination of simple calculation algorithm using TG-43 and the lack of inhomogeneity correction. Dose profiles at 5 mm depth were also generated from TPS calculation and measured with film. The measured and calculated profiles are similar. Consistent with the depth dose curve, the measured dose is lower than the calculated. Conclusion: Our results showed that the Ring Surface Applicator, printed using 3D printer, can generate more uniform dose distribution within the target volume and can be safely used in the clinic.

WE-DE-201-09: Performance of HDR Ring Surface Applicator Printed by 3D Printer

Energy Technology Data Exchange (ETDEWEB)

Xu, Z; Baker, J; Hsia, A; Ryu, S [Stony Brook University Medical Center, East Northport, NY (United States)

2016-06-15

Purpose: The commercially available Leipzig-style Cone for High Dose Rate (HDR) Brachytherapy has a steep depth dose curve and a non-uniform dose distribution. This work shows the performance of a Ring Surface Applicator created using a 3D printer that can generate a better dose distribution. Calculated doses were verified with film measurement. Methods: The water equivalent red-ABS plastic was used to print the Ring Surface Applicator which hosts three catheters: a center piece with a straight catheter and two concentric rings with diameters of 3.5 and 5.5 cm. Gafchromic EBT2 film, Epson Expression 10000 flatbed scanner, and the online software at radiochromic.com were used to analyze the measured data. 10cm×10cm piece of film was sandwiched between two 15×10×5cm3 polystyrene phantoms. The applicator was positioned directly on top of the phantom. Measurement was done using dwell time and positions calculated by Eclipse BrachyVision treatment planning system (RTP). Results: Depth dose curve was generated from the plan and measurement. The results show that the measured and calculated depth dose were in agreement (<3%) from surface to 4mm depth. A discrepancy of 6% was observed at 5 mm depth, where the dose is typically prescribed to. For depths deeper than 5 mm, the measured doses were lower than those calculated by Eclipse BrachyVision. This can be attributed to a combination of simple calculation algorithm using TG-43 and the lack of inhomogeneity correction. Dose profiles at 5 mm depth were also generated from TPS calculation and measured with film. The measured and calculated profiles are similar. Consistent with the depth dose curve, the measured dose is lower than the calculated. Conclusion: Our results showed that the Ring Surface Applicator, printed using 3D printer, can generate more uniform dose distribution within the target volume and can be safely used in the clinic.

Exploring the Notion of the Family Friendly City

Science.gov (United States)

Provi Drianda, Riela

2018-05-01

There is a common perception that downtown areas will never attract families and big cities are not the best place to raise children. Particularly the downtown areas of cities been depicted as the place where criminals, prostitutes, drug-sellers, and other dangerous strangers live. People with children are more likely to look for the suburbs to find bigger housing with more affordable prices, cleaner air, richer nature, a slower lifestyle, and safer environment. However, living in the modern suburb is not always easy and cheap, especially for those who need to commute to the central city. Dealing with the long commutes can be stressful and it affects the health, happiness, and well-being of family members. As the number of modern families with both parents in the workforce is rising, the demand to live closer to the workplace is getting stronger and growing. In some parts of the world, more families increasingly want to live in the cities. This trend can be seen in the United States, Japan, Korea, and Canada. Being family-friendly has become increasingly important for modern cities as more millennial generation show the tendency to raise their families in the urban area. Moreover, it is predicted that two-thirds of world’s population will live in cities by 2030. To accommodate the growing population, in particular, those with children, modern cities should be developed to suit urban families. But what criteria and qualities make one city more family-friendly than another? What would a family-friendly city look like? To date, the number studies exploring the notion of the family-friendly city has been very limited. Most studies have been focusing on the notion of family-friendly dwellings, family-friendly workplaces, or child-friendly cities. This paper brings together and examines the dominant and recurring ideas about the family-friendly city represented in the relevant literature and current urban practices. This paper also questions whether the concept of the

GEMPAK 5.1 - A GENERAL METEOROLOGICAL PACKAGE (UNIX VERSION)

Science.gov (United States)

Desjardins, M. L.

1994-01-01

GEMPAK is a general meteorological software package developed at NASA/Goddard Space Flight Center. It includes programs to analyze and display surface, upper-air, and gridded data, including model output. There are very general programs to list, edit, and plot data on maps, to display profiles and time series, to draw and fill contours, to draw streamlines, to plot symbols for clouds, sky cover, and pressure tendency, and draw cross sections in the case of gridded data and sounding data. In addition, there are Barnes objective analysis programs to grid surface and upper-air data. The programs include the capabilities to derive meteorological parameters from those found in the dataset, to perform vertical interpolations of sounding data to different coordinate systems, and to compute an extensive set of gridded diagnostic quantities by specifying various nested combinations of scalars and vector arithmetic, algebraic, and differential operators. The GEMPAK 5.1 graphics/transformation subsystem, GEMPLT, provides device-independent graphics. GEMPLT also has the capability to display output in a variety of map projections or overlaid on satellite imagery. GEMPAK 5.1 is written in FORTRAN 77 and C-language and has been implemented on VAX computers under VMS and on computers running the UNIX operating system. During installation and normal use, this package occupies approximately 100Mb of hard disk space. The UNIX version of GEMPAK includes drivers for several graphic output systems including MIT's X Window System (X11,R4), Sun GKS, PostScript (color and monochrome), Silicon Graphics, and others. The VMS version of GEMPAK also includes drivers for several graphic output systems including PostScript (color and monochrome). The VMS version is delivered with the object code for the Transportable Applications Environment (TAE) program, version 4.1 which serves as a user interface. A color monitor is recommended for displaying maps on video display devices. Data for rendering

A divergence theorem for pseudo-Finsler spaces

OpenAIRE

Minguzzi, E.

2015-01-01

We study the divergence theorem on pseudo-Finsler spaces and obtain a completely Finslerian version for spaces having a vanishing mean Cartan torsion. This result helps to clarify the problem of energy-momentum conservation in Finsler gravity theories.

Gratitude for Help among Adult Friends and Siblings

Directory of Open Access Journals (Sweden)

Anna Rotkirch

2014-10-01

Full Text Available Although gratitude is a key prosocial emotion reinforcing reciprocal altruism, it has been largely ignored in the empirical literature. We examined feelings of gratitude and the importance of reciprocity in same-sex peer relations. Participants were 772 individuals (189 men; mean age = 28.80 who completed an online survey using a vignette design. We investigated (i differences in reported gratitude and the importance of reciprocity among same-sex siblings and same-sex friends, and (ii how relationship closeness moderates these associations. Based on the theory of kin altruism, we expect that people would feel more grateful towards friends than towards their siblings, and that lack of gratitude or failure to pay back a loan would bother more with friends than with siblings, irrespective of emotional closeness. Results showed that levels of gratitude and expectations of reciprocity were higher towards friends compared to siblings. This was the case also after controlling for emotional closeness. Being close generally made participants feel more grateful and expect lower displays of gratitude in the other. Closeness was also strongly associated with emotional gratitude among siblings compared to friends. We conclude that feelings and displays of gratitude have a special role in friendships. Although a close sibling may elicit as much gratitude as a friend does, even a very close friend is not exempt from the logic of reciprocity in the same way that a sibling is.

What they bring: baseline psychological distress differentially predicts neural response in social exclusion by children's friends and strangers in best friend dyads.

Science.gov (United States)

Baddam, Suman; Laws, Holly; Crawford, Jessica L; Wu, Jia; Bolling, Danielle Z; Mayes, Linda C; Crowley, Michael J

2016-11-01

Friendships play a major role in cognitive, emotional and social development in middle childhood. We employed the online Cyberball social exclusion paradigm to understand the neural correlates of dyadic social exclusion among best friends assessed simultaneously. Each child played with their friend and an unfamiliar player. Event-related potentials (ERPs) were assessed via electroencephalogram during exclusion by friend and unfamiliar peer. Data were analyzed with hierarchical linear modeling to account for nesting of children within friendship dyads. Results showed that stranger rejection was associated with larger P2 and positive slow wave ERP responses compared to exclusion by a friend. Psychological distress differentially moderated the effects of friend and stranger exclusion such that children with greater psychological distress were observed to have larger neural responses (larger P2 and slow wave) to exclusion by a stranger compared to exclusion by a friend. Conversely, children with lower levels of psychological distress had larger neural responses for exclusion by a friend than by a stranger. Psychological distress within the dyad differentially predicted the P2 and slow wave response. Findings highlight the prominent, but differential role of individual and dyadic psychological distress levels in moderating responses to social exclusion in middle childhood. © The Author (2016). Published by Oxford University Press.

WE-F-16A-06: Using 3D Printers to Create Complex Phantoms for Dose Verification, Quality Assurance, and Treatment Planning System Commissioning in Radiotherapy

International Nuclear Information System (INIS)

Kassaee, A; Ding, X; McDonough, J; Reiche, M; Witztum, A; Teo, B

2014-01-01

Purpose: To use 3D printers to design and construct complex geometrical phantoms for commissioning treatment planning systems, dose calculation algorithms, quality assurance (QA), dose delivery, and patient dose verifications. Methods: In radiotherapy, complex geometrical phantoms are often required for dose verification, dose delivery and calculation algorithm validation. Presently, fabrication of customized phantoms is limited due to time, expense and challenges in machining of complex shapes. In this work, we designed and utilized 3D printers to fabricate two phantoms for QA purposes. One phantom includes hills and valleys (HV) for verification of intensity modulated radiotherapy for photons, and protons (IMRT and IMPT). The other phantom includes cylindrical cavities (CC) of various sizes for dose verification of inhomogeneities. We evaluated the HV phantoms for an IMPT beam, and the CC phantom to study various inhomogeneity configurations using photon, electron, and proton beams. Gafcromic ™ films were used to quantify the dose distributions delivered to the phantoms. Results: The HV phantom has dimensions of 12 cm × 12 cm and consists of one row and one column of five peaks with heights ranging from 2 to 5 cm. The CC phantom has a size 10 cm × 14 cm and includes 6 cylindrical cavities with length of 7.2 cm and diameters ranging from 0.6 to 1.2 cm. The IMPT evaluation using the HV phantom shows good agreement as compared to the dose distribution calculated with treatment planning system. The CC phantom also shows reasonable agreements for using different algorithms for each beam modalities. Conclusion: 3D printers with submillimiter resolutions are capable of printing complex phantoms for dose verification and QA in radiotherapy. As printing costs decrease and the technology becomes widely available, phantom design and construction will be readily available to any clinic for testing geometries that were not previously feasible

Organic Foods: Do Eco-Friendly Attitudes Predict Eco-Friendly Behaviors?

Science.gov (United States)

Dahm, Molly J.; Samonte, Aurelia V.; Shows, Amy R.

2009-01-01

Objective: The purpose of this study was to determine whether student awareness and attitudes about organic foods would predict their behaviors with regard to organic food consumption and other healthy lifestyle practices. A secondary purpose was to determine whether attitudes about similar eco-friendly practices would result in socially conscious…

The most common friend first immunization

International Nuclear Information System (INIS)

Nian Fu-Zhong; Hu Cha-Sheng

2016-01-01

In this paper, a standard susceptible-infected-recovered-susceptible(SIRS) epidemic model based on the Watts–Strogatz (WS) small-world network model and the Barabsi–Albert (BA) scale-free network model is established, and a new immunization scheme — “the most common friend first immunization” is proposed, in which the most common friend’s node is described as being the first immune on the second layer protection of complex networks. The propagation situations of three different immunization schemes — random immunization, high-risk immunization, and the most common friend first immunization are studied. At the same time, the dynamic behaviors are also studied on the WS small-world and the BA scale-free network. Moreover, the analytic and simulated results indicate that the immune effect of the most common friend first immunization is better than random immunization, but slightly worse than high-risk immunization. However, high-risk immunization still has some limitations. For example, it is difficult to accurately define who a direct neighbor in the life is. Compared with the traditional immunization strategies having some shortcomings, the most common friend first immunization is effective, and it is nicely consistent with the actual situation. (paper)

When Do Friends Prevent Friends from Hooking Up Intoxicated? An Examination of Sex Differences and Hypothetical Intoxication in Peer Interventions.

Science.gov (United States)

Savage, Matthew W; Menegatos, Lisa; Roberto, Anthony J

2017-08-01

Despite the risks involved when mixing alcohol with casual sexual activity, the majority of college students engage in hookups, and the majority of those hookups involve alcohol. This study focused on the protective role college students' peers can play and the situational factors that might influence their willingness to intervene when a close friend is about to hook up intoxicated. Drawing on the theory of planned behavior (TPB), this study investigated differences in students' (N = 1270) attitudes, norms, perceived behavioral control, and intentions to persuade a close friend not to engage in a hypothetical drunken hookup using a 2 (friend sex) × 2 (participant sex) × 2 (sober/intoxicated) factorial design. Results indicated significant differences in the TPB variables. Participants intended to intervene with female friends, but not male friends, and women were more likely to intervene than men. Participants in the sober condition had stronger intentions to intervene than those in the intoxicated condition, but this effect was driven by increases in men's intentions when sober. Implications for theory and prevention programming are discussed.

Impenetrable Barriers in Phase-Space

International Nuclear Information System (INIS)

Wiggins, S.; Wiesenfeld, L.; Jaffe, C.; Uzer, T.

2001-01-01

Dynamical systems theory is used to construct a general phase-space version of transition state theory. Special multidimensional separatrices are found which act as impenetrable barriers in phase-space between reacting and nonreacting trajectories. The elusive momentum-dependent transition state between reactants and products is thereby characterized. A practical algorithm is presented and applied to a strongly coupled Hamiltonian

Large volume syringe pump extruder for desktop 3D printers

Directory of Open Access Journals (Sweden)

Kira Pusch

2018-04-01

Full Text Available Syringe pump extruders are required for a wide range of 3D printing applications, including bioprinting, embedded printing, and food printing. However, the mass of the syringe becomes a major challenge for most printing platforms, requiring compromises in speed, resolution and/or volume. To address these issues, we have designed a syringe pump large volume extruder (LVE that is compatible with low-cost, open source 3D printers, and herein demonstrate its performance on a PrintrBot Simple Metal. Key aspects of the LVE include: (1 it is open source and compatible with open source hardware and software, making it inexpensive and widely accessible to the 3D printing community, (2 it utilizes a standard 60 mL syringe as its ink reservoir, effectively increasing print volume of the average bioprinter, (3 it is capable of retraction and high speed movements, and (4 it can print fluids using nozzle diameters as small as 100 μm, enabling the printing of complex shapes/objects when used in conjunction with the freeform reversible embedding of suspended hydrogels (FRESH 3D printing method. Printing performance of the LVE is demonstrated by utilizing alginate as a model biomaterial ink to fabricate parametric CAD models and standard calibration objects. Keywords: Additive manufacturing, 3D bioprinting, Embedded printing, FRESH, Soft materials extrusion

Eco-friendly dentistry: Need of future. An overview

Directory of Open Access Journals (Sweden)

Savy Arora

2017-01-01

Full Text Available In today's world, it is very necessary to understand the importance of being eco-friendly in every facet of our lives. The color “green” has healing power and denotes renewal, growth, and hope. “Eco-friendly dentistry” attempts to reduce the detrimental impact of dental practices on the environment and promote environmental awareness and sustainability to patients. This paper attempts to cover all possible aspects of making a dental practice eco-friendly, both in a dental perspective as well as a general perspective. While establishing an eco-friendly dental workplace, the dentist needs to assess his choices in planning the infrastructure and purchasing of equipment and dental materials. Eco-friendly dentistry is a newly evolving practice of dentistry, which encompasses a simultaneous devotion to sustainability, prevention, precaution, and a minimally invasive patient-centric, as well as global-centric treatment. There are two main avenues for implementing eco-friendly dentistry: (1 appropriate policy development and implementation and (2 dentists taking responsibility/ownership in the absence of policies and regulations. Although in some cases, it may take a little extra effort or money; dentists throughout the world are doing their best to reduce the environmental impact of the dental practice. Although the commitment of one small dental office cannot save the planet, certainly, the collective efforts of many small offices as well as large dental hospitals/colleges can ensure that dentists, at least, will not be responsible for destroying it. This article discusses various factors that can be incorporated into dental practice that can help make dentistry eco-friendly.

The problem of general Radon representation for an arbitrary Hausdorff space

Science.gov (United States)

Zakharov, V. K.; Mikhalev, A. V.

1999-10-01

After the fundamental work of Riesz, Radon and Hausdorff in the period 1909-1914, the following problem of general Radon representation emerged: for any Hausdorff space find the space of linear functionals that are integrally representable by Radon measures. In the early 1950s, a partial solution of this problem (the bijective version) for locally compact spaces was obtained by Halmos, Hewitt, Edwards, Bourbaki and others. For bounded Radon measures on a Tychonoff space, the problem of isomorphic Radon representation was solved in 1956 by Prokhorov. In this paper we give a possible solution of the problem of general Radon representation. To do this, we use the family of metasemicontinuous functions with compact support and the class of thin functionals. We present bijective and isomorphic versions of the solution (Theorems 1 and 2 of §2.5). To get the isomorphic version, we introduce the family of Radon bimeasures.

The problem of general Radon representation for an arbitrary Hausdorff space

Energy Technology Data Exchange (ETDEWEB)

Zakharov, V K [St Petersburg State University of Technology and Design (Russian Federation); Mikhalev, A V [M.V. Lomonosov Moscow State University, Moscow (Russian Federation)

1999-10-31

After the fundamental work of Riesz, Radon and Hausdorff in the period 1909-1914, the following problem of general Radon representation emerged: for any Hausdorff space find the space of linear functionals that are integrally representable by Radon measures. In the early 1950s, a partial solution of this problem (the bijective version) for locally compact spaces was obtained by Halmos, Hewitt, Edwards, Bourbaki and others. For bounded Radon measures on a Tychonoff space, the problem of isomorphic Radon representation was solved in 1956 by Prokhorov. In this paper we give a possible solution of the problem of general Radon representation. To do this, we use the family of metasemicontinuous functions with compact support and the class of thin functionals. We present bijective and isomorphic versions of the solution (Theorems 1 and 2 of paragraph 2.5). To get the isomorphic version, we introduce the family of Radon bimeasures.

The problem of general Radon representation for an arbitrary Hausdorff space

International Nuclear Information System (INIS)

Zakharov, V K; Mikhalev, A V

1999-01-01

After the fundamental work of Riesz, Radon and Hausdorff in the period 1909-1914, the following problem of general Radon representation emerged: for any Hausdorff space find the space of linear functionals that are integrally representable by Radon measures. In the early 1950s, a partial solution of this problem (the bijective version) for locally compact spaces was obtained by Halmos, Hewitt, Edwards, Bourbaki and others. For bounded Radon measures on a Tychonoff space, the problem of isomorphic Radon representation was solved in 1956 by Prokhorov. In this paper we give a possible solution of the problem of general Radon representation. To do this, we use the family of metasemicontinuous functions with compact support and the class of thin functionals. We present bijective and isomorphic versions of the solution (Theorems 1 and 2 of paragraph 2.5). To get the isomorphic version, we introduce the family of Radon bimeasures

Self-consistency in the phonon space of the particle-phonon coupling model

Science.gov (United States)

Tselyaev, V.; Lyutorovich, N.; Speth, J.; Reinhard, P.-G.

2018-04-01

In the paper the nonlinear generalization of the time blocking approximation (TBA) is presented. The TBA is one of the versions of the extended random-phase approximation (RPA) developed within the Green-function method and the particle-phonon coupling model. In the generalized version of the TBA the self-consistency principle is extended onto the phonon space of the model. The numerical examples show that this nonlinear version of the TBA leads to the convergence of results with respect to enlarging the phonon space of the model.

Gridded Population of the World, Version 3 (GPWv3): Population Count Grid

Data.gov (United States)

National Aeronautics and Space Administration — Gridded Population of the World, Version 3 (GPWv3) consists of estimates of human population for the years 1990, 1995, and 2000 by 2.5 arc-minute grid cells and...

Moduli spaces of convex projective structures on surfaces

DEFF Research Database (Denmark)

Fock, V. V.; Goncharov, A. B.

2007-01-01

We introduce explicit parametrisations of the moduli space of convex projective structures on surfaces, and show that the latter moduli space is identified with the higher Teichmüller space for defined in [V.V. Fock, A.B. Goncharov, Moduli spaces of local systems and higher Teichmüller theory, math.......AG/0311149]. We investigate the cluster structure of this moduli space, and define its quantum version....

Some fixed point theorems in fuzzy reflexive Banach spaces

International Nuclear Information System (INIS)

Sadeqi, I.; Solaty kia, F.

2009-01-01

In this paper, we first show that there are some gaps in the fixed point theorems for fuzzy non-expansive mappings which are proved by Bag and Samanta, in [Bag T, Samanta SK. Fixed point theorems on fuzzy normed linear spaces. Inf Sci 2006;176:2910-31; Bag T, Samanta SK. Some fixed point theorems in fuzzy normed linear spaces. Inform Sci 2007;177(3):3271-89]. By introducing the notion of fuzzy and α- fuzzy reflexive Banach spaces, we obtain some results which help us to establish the correct version of fuzzy fixed point theorems. Second, by applying Theorem 3.3 of Sadeqi and Solati kia [Sadeqi I, Solati kia F. Fuzzy normed linear space and it's topological structure. Chaos, Solitons and Fractals, in press] which says that any fuzzy normed linear space is also a topological vector space, we show that all topological version of fixed point theorems do hold in fuzzy normed linear spaces.

Friending, IMing, and hanging out face-to-face: overlap in adolescents' online and offline social networks.

Science.gov (United States)

Reich, Stephanie M; Subrahmanyam, Kaveri; Espinoza, Guadalupe

2012-03-01

Many new and important developmental issues are encountered during adolescence, which is also a time when Internet use becomes increasingly popular. Studies have shown that adolescents are using these online spaces to address developmental issues, especially needs for intimacy and connection to others. Online communication with its potential for interacting with unknown others, may put teens at increased risk. Two hundred and fifty-one high school students completed an in-person survey, and 126 of these completed an additional online questionnaire about how and why they use the Internet, their activities on social networking sites (e.g., Facebook, MySpace) and their reasons for participation, and how they perceive these online spaces to impact their friendships. To examine the extent of overlap between online and offline friends, participants were asked to list the names of their top interaction partners offline and online (Facebook and instant messaging). Results reveal that adolescents mainly use social networking sites to connect with others, in particular with people known from offline contexts. While adolescents report little monitoring by their parents, there was no evidence that teens are putting themselves at risk by interacting with unknown others. Instead, adolescents seem to use the Internet, especially social networking sites, to connect with known others. While the study found moderate overlap between teens' closest online and offline friends, the patterns suggest that adolescents use online contexts to strengthen offline relationships. PsycINFO Database Record (c) 2012 APA, all rights reserved.

Constraints in the Adoption of Eco Friendly Conservation Practices

Directory of Open Access Journals (Sweden)

L. Murali Krishnan

2016-05-01

Insect pest and diseases management, Lack of awareness of agro environmental problems and farmer’s attitude towards the Eco Friendly Conservation Practices are the major constraints in the adoption of Eco Friendly Conservation Practices.The study suggests educational, extension & training strategies for fostering the adopted of ECO friendly Conservation Practices.

Influence of Friends on Children’s Physical Activity: A Review

Science.gov (United States)

Maturo, Claire C.

2013-01-01

We examined evidence for friendship influences on children's physical activity (PA) through systematic searches of online databases in May 2012. We identified 106 studies (25 qualitative) published in English since 2000 that analyzed indicators of friendship influences (e.g., communication about PA, friends’ PA, and PA with friends) among persons younger than 19 years. Children's PA was positively associated with encouragement from friends (43 of 55 studies indicating a positive relationship), friends' own PA (30/35), and engagement with friends in PA (9/10). These findings are consistent with friends influencing PA, but most studies did not isolate influence from other factors that could explain similarity. Understanding friendship influences in childhood can facilitate the promotion of lifelong healthy habits. PA with friends should be considered in health promotion programs. PMID:23678914

Parents and friends both matter: simultaneous and interactive influences of parents and friends on European schoolchildren's energy balance-related behaviours - the ENERGY cross-sectional study.

Science.gov (United States)

te Velde, Saskia J; ChinAPaw, Mai J M; De Bourdeaudhuij, Ilse; Bere, Elling; Maes, Lea; Moreno, Luis; Jan, Nataša; Kovacs, Eva; Manios, Yannis; Brug, Johannes

2014-07-08

The family, and parents in particular, are considered the most important influencers regarding children's energy-balance related behaviours (EBRBs). When children become older and gain more behavioural autonomy regarding different behaviours, the parental influences may become less important and peer influences may gain importance. Therefore the current study aims to investigate simultaneous and interactive associations of family rules, parent and friend norms and modelling with soft drink intake, TV viewing, daily breakfast consumption and sport participation among schoolchildren across Europe. A school-based cross-sectional survey in eight countries across Europe among 10-12 year old schoolchildren. Child questionnaires were used to assess EBRBs (soft drink intake, TV viewing, breakfast consumption, sport participation), and potential determinants of these behaviours as perceived by the child, including family rules, parental and friend norms and modelling. Linear and logistic regression analyses (n = 7811) were applied to study the association of parental (norms, modelling and rules) and friend influences (norm and modelling) with the EBRBs. In addition, potential moderating effects of parental influences on the associations of friend influences with the EBRBs were studied by including interaction terms. Children reported more unfavourable friend norms and modelling regarding soft drink intake and TV viewing, while they reported more favourable friend and parental norms and modelling for breakfast consumption and physical activity. Perceived friend and parental norms and modelling were significantly positively associated with soft drink intake, breakfast consumption, physical activity (only modelling) and TV time. Across the different behaviours, ten significant interactions between parental and friend influencing variables were found and suggested a weaker association of friend norms and modelling when rules were in place. Parental and friends norm and

Spillover of environment-friendly consumer behaviour

DEFF Research Database (Denmark)

Thøgersen, John; Ølander, Carl Folke

2003-01-01

This paper contributes empirical input to current reasoning about consumers' propensity to behave in an environmentally friendly way in different domains. Spe-cifically, we investigate whether environmentally friendly behaviours spread to more and more areas of the consumption pattern in a virtuous...... circle and whether it is a necessary prerequisite for a virtuous circle to emerge and to continue to work that the individual possesses certain general values or ethical norms. The data material is a three-wave panel study with a large random sample of Danish consumers. The data were analysed by means...... of structural equation modelling and other techniques. Cases of transfer of environment-friendly conduct between behavioural categories are found, but only in a few of the possible instances and only of a modest size. The panel analysis also identifies a few negative cross-lagged effects. Such effects may...

Tailored sPP/Silica Nano composite for Eco friendly Insulation of Extruded HVDC Cable

International Nuclear Information System (INIS)

Dang, B.; He, J.; Hu, J.; Zhou, Y.

2015-01-01

Cross-linked polyethylene (XLPE) is a thermosetting material that cannot be recycled at the end of its lifetime. This study investigated the potential of syndiotactic polypropylene (sPP)/silica as an eco friendly extruded insulation system for HVDC cables. We investigated the morphology, Fourier transform infrared, and thermal, thermomechanical, and electrical behaviors of sPP modified with 0.5-3% nano silica. We found that the silica/sPP nano composite without cross-linking offered a suitable mechanical modulus at room temperature and sufficient intensity at high temperatures, and adding nano silica modified by a silane coupling agent to the sPP resulted in significant DC resistivity and space charge improvement. The optimal nano silica content in the sPP was determined by balancing the mechanical and thermomechanical characteristics and the DC resistivity. The sPP/silica nano composite reported here shows great potential as a candidate insulation material for future eco friendly extruded HVDC cables.

Print-to-print: printer-enabled out-of-cleanroom multiobject microprinting method.

Science.gov (United States)

Xing, Siyuan; Zhao, Siwei; Pan, Tingrui

2014-01-01

Micropatterning techniques have gained growing interests from a broad range of engineering and biology researches as it realizes the high-throughput and highly quantitative investigations on miniature biological objects (e.g., cells and bacteria) by spatially defined micropatterns. However, most of the existing techniques rely on expensive instruments or intensive cleanroom access which may not be easy to be utilized in a regular biological laboratory. Here, we present the detailed procedures of a simple versatile microprinting process, referred to as Print-to-Print (P2P), to form multiobject micropatterns for potential biological applications. Only a solid-phase printer and custom-made superhydrophobic (SH) films are utilized for the printing and no thermal or chemical treatment is involved during the entire printing process. Moreover, the noncontact nature of droplet transferring and printing steps can be highly advantageous for sensitive biological uses. By the P2P process, a minimal feature resolution of 229 ± 17 μm has been successfully achieved. What's more, this approach has been applied to form micropatterning on various commonly used substrates in biology as well as multiobject co-patterns. In addition, the SH substrates have also been demonstrated to be reusable. Copyright © 2014 Elsevier Inc. All rights reserved.

Lipedema: friend and foe.

Science.gov (United States)

Torre, Yanira Sanchez-De la; Wadeea, Rita; Rosas, Victoria; Herbst, Karen L

2018-03-09

Background Lipedema is a chronic disorder presenting in women during puberty or other times of hormonal change such as childbirth or menopause, characterized by symmetric enlargement of nodular, painful subcutaneous adipose tissue (fat) in the limbs, sparing the hands, feet and trunk. Healthcare providers underdiagnose or misdiagnose lipedema as obesity or lymphedema. Materials and methods The benefits (friend) and negative aspects (foe) of lipedema were collected from published literature, discussions with women with lipedema, and institutional review board approved evaluation of medical charts of 46 women with lipedema. Results Lipedema is a foe because lifestyle change does not reduce lipedema fat, the fat is painful, can become obese, causes gait and joint abnormalities, fatigue, lymphedema and psychosocial distress. Hypermobility associated with lipedema can exacerbate joint disease and aortic disease. In contrast, lipedema fat can be a friend as it is associated with relative reductions in obesity-related metabolic dysfunction. In new data collected, lipedema was associated with a low risk of diabetes (2%), dyslipidemia (11.7%) and hypertension (13%) despite an obese average body mass index (BMI) of 35.3 ± 1.7 kg/m2. Conclusion Lipedema is a painful psychologically distressing fat disorder, more foe than friend especially due to associated obesity and lymphedema. More controlled studies are needed to study the mechanisms and treatments for lipedema.

Unix version of CALOR89 for calorimeter applications

International Nuclear Information System (INIS)

Handler, T.

1992-01-01

CALOR89 is a system of coupled Monte Carlo particle transport computer codes which has been successfully employed for the estimation of calorimeter parameters in High Energy Physics. In the past CALOR89 has been running on various IBM machines and on CRAY X-MP at Lawrence Livermore Lab. These machines had non-unix operating systems. In this report we present a UNIX version of CALOR89, which is especially suited for the UNIX work stations. Moreover CALOR89 is also been supplemented with two new program packages which makes it more user friendly. CALPREP is a program for the preparation of the input files for CALOR89 in general geometry and ANALYZ is an analysis package to extract the final results from CALOR89 relevant to calorimeters. This report also provides two script files LCALOR and PCALOR. LCALOR runs CALOR89 sequences of programs and EGS4 for a given configuration sequentially on a single processor and PCALOR concurrently on a multiprocessor unix workstation

Fermilab Friends for Science Education | Contact Us

Science.gov (United States)

Fermilab Friends for Science Education FFSE Home About Us Join Us Support Us Contact Us Contact Us Science Education P.O Box 500, MS 777 Batavia, IL 60510-5011 (630) 840-3094 * fax: (630) 840-2500 E-mail : Membership Send all other communications to: Susan Dahl, President Fermilab Friends for Science Education Box

Development of paper-based microfluidic analytical device for iron assay using photomask printed with 3D printer for fabrication of hydrophilic and hydrophobic zones on paper by photolithography.

Science.gov (United States)

Asano, Hitoshi; Shiraishi, Yukihide

2015-07-09

This paper describes a paper-based microfluidic analytical device for iron assay using a photomask printed with a 3D printer for fabrication of hydrophilic and hydrophobic zones on the paper by photolithography. Several designed photomasks for patterning paper-based microfluidic analytical devices can be printed with a 3D printer easily, rapidly and inexpensively. A chromatography paper was impregnated with the octadecyltrichlorosilane n-hexane solution and hydrophobized. After the hydrophobic zone of the paper was exposed to the UV light through the photomask, the hydrophilic zone was generated. The smallest functional hydrophilic channel and hydrophobic barrier were ca. 500 μm and ca. 100 μm in width, respectively. The fabrication method has high stability, resolution and precision for hydrophilic channel and hydrophobic barrier. This test paper was applied to the analysis of iron in water samples using a colorimetry with phenanthroline. Copyright © 2015 Elsevier B.V. All rights reserved.

Does it matter what friends think, say, or do? The role of friends' smoking attitudes and behavior for Dutch adolescents' smoking behavior.

Science.gov (United States)

Huisman, Chip

2014-05-01

Using stochastic actor-based models for longitudinal network analysis, this study examines the role of friends' smoking attitudes and behavior for Dutch adolescents' smoking behavior in four secondary schools (N = 875). The data were collected in two waves in two small suburban towns under second graders in 2008 to 2009 by means of a standardized questionnaire. Stochastic actor-based models for longitudinal network analysis can control for friendship selection while examining the effect of friends' attitudes and smoking behavior on the smoking behavior of a student. The findings suggest that friends tend to select each other on similar smoking behavior. Influence of friends' smoking behavior seems to play no role. In one school, an effect of friends' attitudes towards smoking on the smoking behavior is found. The implications for future research are to consider attitudes when examining the influence of friendship network on smoking behavior. The main limitation of this study lies in the limited sample, which makes generalizations to the general population difficult.

Phase space descriptions for simplicial 4D geometries

International Nuclear Information System (INIS)

Dittrich, Bianca; Ryan, James P

2011-01-01

Starting from the canonical phase space for discretized (4D) BF theory, we implement a canonical version of the simplicity constraints and construct phase spaces for simplicial geometries. Our construction allows us to study the connection between different versions of Regge calculus and approaches using connection variables, such as loop quantum gravity. We find that on a fixed triangulation the (gauge invariant) phase space associated with loop quantum gravity is genuinely larger than the one for length and even area Regge calculus. Rather, it corresponds to the phase space of area-angle Regge calculus, as defined in [1] (prior to the imposition of gluing constraints, which ensure the metricity of the triangulation). Finally, we show that for a subclass of triangulations one can construct first-class Hamiltonian and diffeomorphism constraints leading to flat 4D spacetimes.

Weighted local Hardy spaces associated with operators

Indian Academy of Sciences (India)

RUMING GONG

2018-04-24

5 days ago ... Studies 116 (1985) (Amsterdam: North Holland). [12] Gong R M and Yan L X, Littlewood–Paley and spectral multipliers on weighted L p spaces, J. Geom. Anal. 24 (2014) 873–900. [13] Gong R M, Li J and Yan L X, A local version of Hardy spaces associated with operators on metric spaces, Sci. China Math.

GEMPAK 5.1 - A GENERAL METEOROLOGICAL PACKAGE (VAX VMS VERSION)

Science.gov (United States)

Des, Jardins M. L.

1994-01-01

GEMPAK is a general meteorological software package developed at NASA/Goddard Space Flight Center. It includes programs to analyze and display surface, upper-air, and gridded data, including model output. There are very general programs to list, edit, and plot data on maps, to display profiles and time series, to draw and fill contours, to draw streamlines, to plot symbols for clouds, sky cover, and pressure tendency, and draw cross sections in the case of gridded data and sounding data. In addition, there are Barnes objective analysis programs to grid surface and upper-air data. The programs include the capabilities to derive meteorological parameters from those found in the dataset, to perform vertical interpolations of sounding data to different coordinate systems, and to compute an extensive set of gridded diagnostic quantities by specifying various nested combinations of scalars and vector arithmetic, algebraic, and differential operators. The GEMPAK 5.1 graphics/transformation subsystem, GEMPLT, provides device-independent graphics. GEMPLT also has the capability to display output in a variety of map projections or overlaid on satellite imagery. GEMPAK 5.1 is written in FORTRAN 77 and C-language and has been implemented on VAX computers under VMS and on computers running the UNIX operating system. During installation and normal use, this package occupies approximately 100Mb of hard disk space. The UNIX version of GEMPAK includes drivers for several graphic output systems including MIT's X Window System (X11,R4), Sun GKS, PostScript (color and monochrome), Silicon Graphics, and others. The VMS version of GEMPAK also includes drivers for several graphic output systems including PostScript (color and monochrome). The VMS version is delivered with the object code for the Transportable Applications Environment (TAE) program, version 4.1 which serves as a user interface. A color monitor is recommended for displaying maps on video display devices. Data for rendering

Bio-sample detection on paper-based devices with inkjet printer-sprayed reagents.

Science.gov (United States)

Liang, Wun-Hong; Chu, Chien-Hung; Yang, Ruey-Jen

2015-12-01

The reagent required for bio-sample detection on paper-based analytical devices is generally introduced manually using a pipette. Such an approach is time-consuming; particularly if a large number of devices are required. Automated methods provide a far more convenient solution for large-scale production, but incur a substantial cost. Accordingly, the present study proposes a low-cost method for the paper-based analytical devices in which the biochemical reagents are sprayed onto the device directly using a modified commercial inkjet printer. The feasibility of the proposed method is demonstrated by performing aspartate aminotransferase (AST) and alanine aminotransferase (ALT) tests using simple two-dimensional (2D) paper-based devices. In both cases, the reaction process is analyzed using an image-processing-based colorimetric method. The experimental results show that for AST detection within the 0-105 U/l concentration range, the optimal observation time is around four minutes, while for ALT detection in the 0-125 U/l concentration range, the optimal observation time is approximately one minute. Finally, for both samples, the detection performance of the sprayed-reagent analytical devices is insensitive to the glucose concentration. Copyright © 2015 Elsevier B.V. All rights reserved.

Latest NASA Instrument Cost Model (NICM): Version VI

Science.gov (United States)

Mrozinski, Joe; Habib-Agahi, Hamid; Fox, George; Ball, Gary

2014-01-01

The NASA Instrument Cost Model, NICM, is a suite of tools which allow for probabilistic cost estimation of NASA's space-flight instruments at both the system and subsystem level. NICM also includes the ability to perform cost by analogy as well as joint confidence level (JCL) analysis. The latest version of NICM, Version VI, was released in Spring 2014. This paper will focus on the new features released with NICM VI, which include: 1) The NICM-E cost estimating relationship, which is applicable for instruments flying on Explorer-like class missions; 2) The new cluster analysis ability which, alongside the results of the parametric cost estimation for the user's instrument, also provides a visualization of the user's instrument's similarity to previously flown instruments; and 3) includes new cost estimating relationships for in-situ instruments.

Space dosimetry measurement results using the Pille instrument during the EUROMIR/NASAMIR space flights

International Nuclear Information System (INIS)

Hejja, I.; Apathy, J.; Deme, S.

1997-01-01

The Pille dosimeter developed in Hungary for space applications is described briefly, and its two versions are presented for the two space flights. The results of the EUROMIR mission in 1995-1996 are discussed for positional dosimetric applications. The characteristic dose rates at various space stations in the Salyut range are displayed. The NASAMIR4 mission between January 1997 and September 1998 are also discussed from the dosimetric point of view. The results of the measurements are presented and a preliminary analysis is reported. (R.P.)

Parental Strategies for Knowledge of Adolescents’ Friends: Distinct from Monitoring?

Science.gov (United States)

Miller, Brenda A.; Duke, Michael R.; Ames, Genevieve M.

2012-01-01

Parental monitoring is defined as a set of behaviors used to gain knowledge about an adolescent’s whereabouts, friends and associates, and activities. However, can knowledge of adolescents’ whereabouts/activities, and friends all be attained through the same strategies? Or do they require their own strategies? This study used qualitative interviews with 173 parents of older adolescents from 100 families. Emergent themes described strategies by which parents gain information about their adolescents’ friends and the substance use of those friends. The strategies included direct interaction with the friend, gaining information from the teen, using second-hand sources, and making assumptions. Some of these strategies were consistent with previous research, while others raise new questions and provide interesting new directions to pursue. Primarily, additional consideration needs to be given to assessments of parental monitoring that include strategies for gaining knowledge of adolescents’ friends and their substance use. PMID:23209361

A computationally efficient software application for calculating vibration from underground railways

International Nuclear Information System (INIS)

Hussein, M F M; Hunt, H E M

2009-01-01

The PiP model is a software application with a user-friendly interface for calculating vibration from underground railways. This paper reports about the software with a focus on its latest version and the plans for future developments. The software calculates the Power Spectral Density of vibration due to a moving train on floating-slab track with track irregularity described by typical values of spectra for tracks with good, average and bad conditions. The latest version accounts for a tunnel embedded in a half space by employing a toolbox developed at K.U. Leuven which calculates Green's functions for a multi-layered half-space.

NCTPlan. The new PC version of MacNCTPlan improvements and validation of the treatment planning system

International Nuclear Information System (INIS)

Gonzalez, S.J.; Santa Cruz, Gustavo A.; Yam, C.S.

2003-01-01

Full text: The treatment planning system that has been used routinely in phase-I clinical trials of BNCT at Harvard/MIT consists of the MacNCTPlan interactive planning software coupled to the MCNP 4B Monte Carlo radiation transport code. The physical and mathematical principles of MacNCTPlan as well as its architecture, operation and application have been previously described elsewhere. The use of this software in clinical trials together with a detailed analysis of the code led to the identification of some limitations and deficiencies. The motivation for this PC version, Neutron Capture Therapy Planning, relies basically in two major reasons: the need to integrate the different steps for making a plan and the need to improve some features of the Macintosh version. NCTPlan aims to reproduce all the features and capabilities present in the Macintosh version. Working on this, some deficiencies were corrected and several changes in the interface were performed in order to provide a more friendly and reliable program. Among the changes intended to facilitate the treatment planning process, the most important are the integration of the auxiliary program MPREP to NCTPlan and a great improvement in the visualization of isodose contours. NCTPlan has the ability to show the isodose distributions superimposed on two orthogonal planes of the CT volume, these planes being updated in real time as the orientation of the planes is changed. The major modifications to the mathematical algorithms concerned the material assignment in the geometric model, dose distribution calculations and three-dimensional dose-volume histogram (DVH) derivation. Therefore, NCTPlan provides a user-friendly interface thanks to the integration of the different steps involved in treatment planning. Complete control of the MCNP radiation transport code is under study. Cross-validation of NCTPlan against reference calculations made apparent the improvements performed on the mathematical algorithms

The Impact of Disclosure of Intimate Partner Violence on Friends.

Science.gov (United States)

Sigurvinsdottir, Rannveig; Riger, Stephanie; Ullman, Sarah E

2016-11-01

Intimate partner violence (IPV) affects people connected to survivors as well as survivors themselves. Despite this, we do not have measures assessing IPV's impact on others. The Impact on Friends measure was developed to understand the impact of disclosure of sexual assault (SA) on friends of survivors. In the present study, the Impact on Friends measure was modified to apply to IPV and administered to two separate online samples. Exploratory factor analysis in one sample (U.S.-based participants) revealed a very similar factor structure to the original Impact on Friends measure, consisting of Emotional Distress, Validation, and Confusion. This factor solution was then applied to the next sample (mostly Indian participants), resulting in an adequate model fit. The Impact on Friends-IPV measure has adequate reliability. One of its factors, Emotional Distress, is related to increased depression and post-traumatic distress disorder symptoms of friends, but only in the U.S. These findings suggest that even though the same dimensions have been found in both a U.S. and an Indian sample, how disclosure of IPV on friends relates to psychological symptoms may differ. This study suggest that there is at least some overlap in the experiences of friends of IPV and SA survivors, but that certain dimensions of the measure may have different relationships to other phenomena in different cultures. © The Author(s) 2015.

Why acting environmentally-friendly feels good: Exploring the role of self-image

Directory of Open Access Journals (Sweden)

Leonie A Venhoeven

2016-11-01

Full Text Available Recent research suggests that engagement in environmentally-friendly behavior can feel good. Current explanations for such a link do not focus on the nature of environmentally-friendly behavior itself, but rather propose well-being is more or less a side-benefit; behaviors that benefit environmental quality (e.g. spending one’s money on people rather than products also tend to make us feel good. We propose that the moral nature of environmentally-friendly behavior itself may elicit positive emotions as well, because engaging in this behavior can signal one is an environmentally-friendly and thus a good person. Our results show that engagement in environmentally-friendly behavior can indeed affect how people see themselves: participants saw themselves as being more environmentally-friendly when they engaged in more environmentally-friendly behavior (Study 1. Furthermore, environmentally-friendly behavior resulted in a more positive self-image, more strongly when it was voluntarily engaged in, compared to when it was driven by situational constraints (Study 2. In turn, the more environmentally-friendly (Study 1 and positive (Study 2 people saw themselves, the better they felt about acting environmentally-friendly. Together, these results suggest that the specific self-signal that ensues from engaging in environmentally-friendly behavior can explain why environmentally-friendly actions may elicit a good feeling.

Geometry of Moishezon and 1-convex spaces II: Projectivity of Moishezon spaces and its non-compact version

International Nuclear Information System (INIS)

Sitaramayya, M.

1993-11-01

After a brief review of the geometry of Moishezon spaces, their relation with l-convex spaces and a reasonable and up to date understanding of the obstructions for projectivity of Moishezon objects both in singular and non-singular case is given. The geometry of l-convex manifolds and with l-dimensional exceptional set is studied and some problems and conjectures are stated. The tools of cohomology vanishing theorems important for the subject are briefly sketched. Compactifications of C 3 and Stein spaces are finally outlined. given. 111 refs, 2 figs

Network-Friendly Gossiping

Science.gov (United States)

Serbu, Sabina; Rivière, Étienne; Felber, Pascal

The emergence of large-scale distributed applications based on many-to-many communication models, e.g., broadcast and decentralized group communication, has an important impact on the underlying layers, notably the Internet routing infrastructure. To make an effective use of network resources, protocols should both limit the stress (amount of messages) on each infrastructure entity like routers and links, and balance as much as possible the load in the network. Most protocols use application-level metrics such as delays to improve efficiency of content dissemination or routing, but the extend to which such application-centric optimizations help reduce and balance the load imposed to the infrastructure is unclear. In this paper, we elaborate on the design of such network-friendly protocols and associated metrics. More specifically, we investigate random-based gossip dissemination. We propose and evaluate different ways of making this representative protocol network-friendly while keeping its desirable properties (robustness and low delays). Simulations of the proposed methods using synthetic and real network topologies convey and compare their abilities to reduce and balance the load while keeping good performance.

Hydrochromic molecular switches for water-jet rewritable paper

Science.gov (United States)

Sheng, Lan; Li, Minjie; Zhu, Shaoyin; Li, Hao; Xi, Guan; Li, Yong-Gang; Wang, Yi; Li, Quanshun; Liang, Shaojun; Zhong, Ke; Zhang, Sean Xiao-An

2014-01-01

The days of rewritable paper are coming, printers of the future will use water-jet paper. Although several kinds of rewritable paper have been reported, practical usage of them is rare. Herein, a new rewritable paper for ink-free printing is proposed and demonstrated successfully by using water as the sole trigger to switch hydrochromic dyes on solid media. Water-jet prints with various colours are achieved with a commercial desktop printer based on these hydrochromic rewritable papers. The prints can be erased and rewritten dozens of times with no significant loss in colour quality. This rewritable paper is promising in that it can serve an eco-friendly information display to meet the increasing global needs for environmental protection.

[External cephalic version].

Science.gov (United States)

Navarro-Santana, B; Duarez-Coronado, M; Plaza-Arranz, J

2016-08-01

To analyze the rate of successful external cephalic versions in our center and caesarean sections that would be avoided with the use of external cephalic versions. From January 2012 to March 2016 external cephalic versions carried out at our center, which were a total of 52. We collected data about female age, gestational age at the time of the external cephalic version, maternal body mass index (BMI), fetal variety and situation, fetal weight, parity, location of the placenta, amniotic fluid index (ILA), tocolysis, analgesia, and newborn weight at birth, minor adverse effects (dizziness, hypotension and maternal pain) and major adverse effects (tachycardia, bradycardia, decelerations and emergency cesarean section). 45% of the versions were unsuccessful and 55% were successful. The percentage of successful vaginal delivery in versions was 84% (4% were instrumental) and 15% of caesarean sections. With respect to the variables studied, only significant differences in birth weight were found; suggesting that birth weight it is related to the outcome of external cephalic version. Probably we did not find significant differences due to the number of patients studied. For women with breech presentation, we recommend external cephalic version before the expectant management or performing a cesarean section. The external cephalic version increases the proportion of fetuses in cephalic presentation and also decreases the rate of caesarean sections.

Health effects of laser printer emissions: a controlled exposure study.

Science.gov (United States)

Karrasch, S; Simon, M; Herbig, B; Langner, J; Seeger, S; Kronseder, A; Peters, S; Dietrich-Gümperlein, G; Schierl, R; Nowak, D; Jörres, R A

2017-07-01

Ultrafine particles emitted from laser printers are suspected to elicit adverse health effects. We performed 75-minute exposures to emissions of laser printing devices (LPDs) in a standardized, randomized, cross-over manner in 23 healthy subjects, 14 mild, stable asthmatics, and 15 persons reporting symptoms associated with LPD emissions. Low-level exposures (LLE) ranged at the particle background (3000 cm -3 ) and high-level exposures (HLE) at 100 000 cm -3 . Examinations before and after exposures included spirometry, body plethysmography, transfer factors for CO and NO (TLCO, TLNO), bronchial and alveolar NO, cytokines in serum and nasal secretions (IL-1β, IL-5, IL-6, IL-8, GM-CSF, IFNγ, TNFα), serum ECP, and IgE. Across all participants, no statistically significant changes occurred for lung mechanics and NO. There was a decrease in volume-related TLNO that was more pronounced in HLE, but the difference to LLE was not significant. ECP and IgE increased in the same way after exposures. Nasal IL-6 showed a higher increase after LLE. There was no coherent pattern regarding the responses in the participant subgroups or single sets of variables. In conclusion, the experimental acute responses to short but very high-level LPD exposures were small and did not indicate clinically relevant effects compared to low particle number concentrations. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

FROM CAD MODEL TO 3D PRINT VIA “STL” FILE FORMAT

Directory of Open Access Journals (Sweden)

Cătălin IANCU

2010-06-01

Full Text Available The paper work presents the STL file format, which is now used for transferring information from CAD software to a 3D printer, for obtaining the solid model in Rapid prototyping and Computer Aided Manufacturing. It’s presented also the STL format structure, its history, limitations and further development, as well as its new version to arrive and other similar file formats. As a conclusion, STL files used to transfer data from CAD package to 3D printers has a series of limitations and therefore new formats will replace it soon.

Global climate-friendly trade : Canada's chance to clean up

International Nuclear Information System (INIS)

Goldfarb, D.

2010-03-01

This paper discussed the global trade and investment in climate-friendly technologies, Canada's current position in this market, and the policy changes that are necessary for Canadian businesses to gain a stronger foothold in this sector. The global market for climate-friendly technologies is growing rapidly, but Canadian businesses have generally failed to exploit opportunities to export climate-friendly technologies and have generally lagged other countries in adopting such technologies developed elsewhere. Although Canadian businesses generally underperform in this sector, Canada does have notable strengths in 13 identified areas, including waste management technologies, energy technologies, and in parts of the value chains associated with wind and solar power. Targeting these areas of relative strength for further development could position Canada as a global leader in some climate-friendly technologies. For this to happen, Canadian governments need to establish clear policies, invest in research and development, and remove domestic and international barriers to the development and trade in climate-friendly technologies. 30 refs., 5 tabs., 5 figs.

Accessible bioprinting: adaptation of a low-cost 3D-printer for precise cell placement and stem cell differentiation.

Science.gov (United States)

Reid, John A; Mollica, Peter A; Johnson, Garett D; Ogle, Roy C; Bruno, Robert D; Sachs, Patrick C

2016-06-07

The precision and repeatability offered by computer-aided design and computer-numerically controlled techniques in biofabrication processes is quickly becoming an industry standard. However, many hurdles still exist before these techniques can be used in research laboratories for cellular and molecular biology applications. Extrusion-based bioprinting systems have been characterized by high development costs, injector clogging, difficulty achieving small cell number deposits, decreased cell viability, and altered cell function post-printing. To circumvent the high-price barrier to entry of conventional bioprinters, we designed and 3D printed components for the adaptation of an inexpensive 'off-the-shelf' commercially available 3D printer. We also demonstrate via goal based computer simulations that the needle geometries of conventional commercially standardized, 'luer-lock' syringe-needle systems cause many of the issues plaguing conventional bioprinters. To address these performance limitations we optimized flow within several microneedle geometries, which revealed a short tapered injector design with minimal cylindrical needle length was ideal to minimize cell strain and accretion. We then experimentally quantified these geometries using pulled glass microcapillary pipettes and our modified, low-cost 3D printer. This systems performance validated our models exhibiting: reduced clogging, single cell print resolution, and maintenance of cell viability without the use of a sacrificial vehicle. Using this system we show the successful printing of human induced pluripotent stem cells (hiPSCs) into Geltrex and note their retention of a pluripotent state 7 d post printing. We also show embryoid body differentiation of hiPSC by injection into differentiation conducive environments, wherein we observed continuous growth, emergence of various evaginations, and post-printing gene expression indicative of the presence of all three germ layers. These data demonstrate an

Low Elevation Coastal Zone (LECZ) Urban-Rural Population and Land Area Estimates, Version 2

Data.gov (United States)

National Aeronautics and Space Administration — The Low Elevation Coastal Zone (LECZ) Urban-Rural Population and Land Area Estimates, Version 2 data set consists of country-level estimates of urban population,...

Getting to Family-Friendly in Your Department

Science.gov (United States)

Pilachowski, Catherine A.

2012-01-01

These days, most academic and research institutions recognize the importance of a family-friendly workplace, and have implemented at least some policies to support a sustainable work-life balance: family and medical leave, parental leave, stopping or extending tenure clocks, modified duty policies, breast feeding policies and lactation rooms, partner hiring programs, childcare programs, eldercare programs, emergency and sick child care programs, dependent care travel funds, etc. But while institutions may offer a menu of policies and free or low-cost services to support families, what's happening in your department? Achieving a supportive workplace culture requires that we dispel some of the myths associated with family-friendly policies, and establish that family-friendly policies not only benefit all employees, but also help the institution be more successful.

Scaffold-Free Tubular Tissues Created by a Bio-3D Printer Undergo Remodeling and Endothelialization when Implanted in Rat Aortae

Science.gov (United States)

Itoh, Manabu; Nakayama, Koichi; Noguchi, Ryo; Kamohara, Keiji; Furukawa, Kojirou; Uchihashi, Kazuyoshi; Toda, Shuji; Oyama, Jun-ichi; Node, Koichi; Morita, Shigeki

2015-01-01

Background Small caliber vascular prostheses are not clinically available because synthetic vascular prostheses lack endothelial cells which modulate platelet activation, leukocyte adhesion, thrombosis, and the regulation of vasomotor tone by the production of vasoactive substances. We developed a novel method to create scaffold-free tubular tissue from multicellular spheroids (MCS) using a “Bio-3D printer”-based system. This system enables the creation of pre-designed three-dimensional structures using a computer controlled robotics system. With this system, we created a tubular structure and studied its biological features. Methods and Results Using a “Bio-3D printer,” we made scaffold-free tubular tissues (inner diameter of 1.5 mm) from a total of 500 MCSs (2.5× 104 cells per one MCS) composed of human umbilical vein endothelial cells (40%), human aortic smooth muscle cells (10%), and normal human dermal fibroblasts (50%). The tubular tissues were cultured in a perfusion system and implanted into the abdominal aortas of F344 nude rats. We assessed the flow by ultrasonography and performed histological examinations on the second (n = 5) and fifth (n = 5) day after implantation. All grafts were patent and remodeling of the tubular tissues (enlargement of the lumen area and thinning of the wall) was observed. A layer of endothelial cells was confirmed five days after implantation. Conclusions The scaffold-free tubular tissues made of MCS using a Bio-3D printer underwent remodeling and endothelialization. Further studies are warranted to elucidate the underlying mechanism of endothelialization and its function, as well as the long-term results. PMID:26325298

Construction of Realistic Liver Phantoms from Patient Images using 3D Printer and Its Application in CT Image Quality Assessment.

Science.gov (United States)

Leng, Shuai; Yu, Lifeng; Vrieze, Thomas; Kuhlmann, Joel; Chen, Baiyu; McCollough, Cynthia H

2015-01-01

The purpose of this study is to use 3D printing techniques to construct a realistic liver phantom with heterogeneous background and anatomic structures from patient CT images, and to use the phantom to assess image quality with filtered backprojection and iterative reconstruction algorithms. Patient CT images were segmented into liver tissues, contrast-enhanced vessels, and liver lesions using commercial software, based on which stereolithography (STL) files were created and sent to a commercial 3D printer. A 3D liver phantom was printed after assigning different printing materials to each object to simulate appropriate attenuation of each segmented object. As high opacity materials are not available for the printer, we printed hollow vessels and filled them with iodine solutions of adjusted concentration to represent enhance levels in contrast-enhanced liver scans. The printed phantom was then placed in a 35×26 cm oblong-shaped water phantom and scanned repeatedly at 4 dose levels. Images were reconstructed using standard filtered backprojection and an iterative reconstruction algorithm with 3 different strength settings. Heterogeneous liver background were observed from the CT images and the difference in CT numbers between lesions and background were representative for low contrast lesions in liver CT studies. CT numbers in vessels filled with iodine solutions represented the enhancement of liver arteries and veins. Images were run through a Channelized Hotelling model observer with Garbor channels and ROC analysis was performed. The AUC values showed performance improvement using the iterative reconstruction algorithm and the amount of improvement increased with strength setting.

3D Printer Generated Tissue iMolds for Cleared Tissue Using Single- and Multi-Photon Microscopy for Deep Tissue Evaluation.

Science.gov (United States)

Miller, Sean J; Rothstein, Jeffrey D

2017-01-01

Pathological analyses and methodology has recently undergone a dramatic revolution. With the creation of tissue clearing methods such as CLARITY and CUBIC, groups can now achieve complete transparency in tissue samples in nano-porous hydrogels. Cleared tissue is then imagined in a semi-aqueous medium that matches the refractive index of the objective being used. However, one major challenge is the ability to control tissue movement during imaging and to relocate precise locations post sequential clearing and re-staining. Using 3D printers, we designed tissue molds that fit precisely around the specimen being imaged. First, images are taken of the specimen, followed by importing and design of a structural mold, then printed with affordable plastics by a 3D printer. With our novel design, we have innovated tissue molds called innovative molds (iMolds) that can be generated in any laboratory and are customized for any organ, tissue, or bone matter being imaged. Furthermore, the inexpensive and reusable tissue molds are made compatible for any microscope such as single and multi-photon confocal with varying stage dimensions. Excitingly, iMolds can also be generated to hold multiple organs in one mold, making reconstruction and imaging much easier. Taken together, with iMolds it is now possible to image cleared tissue in clearing medium while limiting movement and being able to relocate precise anatomical and cellular locations on sequential imaging events in any basic laboratory. This system provides great potential for screening widespread effects of therapeutics and disease across entire organ systems.

A Feasibility Study into the Use of Three-Dimensional Printer Modelling in Acetabular Fracture Surgery

Directory of Open Access Journals (Sweden)

A. W. Yu

2015-01-01

Full Text Available There are a number of challenges associated with the operative treatment of acetabular fractures. The approach used is often extensive, while operative time and perioperative blood loss can also be significant. With the proliferation of 3D printer technology, we present a fast and economical way to aid the operative planning of complex fractures. We used augmented stereoscopic 3D CT reconstructions to allow for an appreciation of the normal 3D anatomy of the pelvis on the fractured side and to use the models for subsequent intraoperative contouring of pelvic reconstruction plates. This leads to a reduction in the associated soft tissue trauma, reduced intraoperative time and blood loss, minimal handling of the plate, and reduced fluoroscopic screening times. We feel that the use of this technology to customize implants, plates, and the operative procedure to a patient’s unique anatomy can only lead to improved outcomes.

A Rapid Generation Method of Character Doll with Rotatable Limbs Oriented to 3D Printer

Institute of Scientific and Technical Information of China (English)

LI Lin; CHU Xiao-li; Nie Wen-chao

2014-01-01

Currently, 3D printing of the character dolls is a very practical application for the average person. But the model of doll which can be obtained is static so the posture of the doll is single. On the other hand, the modification of the model is very difficult to non-professions. This paper proposes an rapid generation method of character doll with rotatable limbs, which is through adding the sphere joint to the doll’s model automatically. After the model is segmented by drawing a line interactively, the sphere joint is created based on the segmentation boundary through entity modeling method. Lastly the two models of the doll and the joint are composited and printed. Some doll’s model are tested on the FDM(Fused Deposition Modeling) 3D printer using this process. The results are more interesting and the efficiency has been greatly improved compared with modifying the model manually.

Designing the robot inclusive space challenge

Directory of Open Access Journals (Sweden)

Rajesh Elara Mohan

2015-11-01

Full Text Available A novel robotic challenge, namely the robot inclusive spaces (RIS challenge, is proposed in this paper, which is a cross disciplinary and design focused initiative. It aims to foster the roboticists, architects, and designers towards realizing robot friendly social spaces. Contrary to conventional robotics competitions focusing on designing robots and its component technologies, robot inclusive spaces challenge adopts an interdisciplinary “design for robots” strategy to overcome the traditional research problem in real world deployments of social robots. In order to realize the RIS, various architectural elements must be adapted including: design principles for inclusive spaces, lighting schemes, furniture choices and arrangement, wall and floor surfaces, pathways among others. This paper introduces the format and design principles of RIS challenge, presents a first run of the challenge, and gives the corresponding analysis.

What's in a Friendship? Partner Visibility Supports Cognitive Collaboration between Friends.

Science.gov (United States)

Brennan, Allison A; Enns, James T

2015-01-01

Not all cognitive collaborations are equally effective. We tested whether friendship and communication influenced collaborative efficiency by randomly assigning participants to complete a cognitive task with a friend or non-friend, while visible to their partner or separated by a partition. Collaborative efficiency was indexed by comparing each pair's performance to an optimal individual performance model of the same two people. The outcome was a strong interaction between friendship and partner visibility. Friends collaborated more efficiently than non-friends when visible to one another, but a partition that prevented pair members from seeing one another reduced the collaborative efficiency of friends and non-friends to a similar lower level. Secondary measures suggested that verbal communication differences, but not psychophysiological arousal, contributed to these effects. Analysis of covariance indicated that females contributed more than males to overall levels of collaboration, but that the interaction of friendship and visibility was independent of that effect. These findings highlight the critical role of partner visibility in the collaborative success of friends.

Duplication of complete dentures using general-purpose handheld optical scanner and 3-dimensional printer: Introduction and clinical considerations.

Science.gov (United States)

Kurahashi, Kosuke; Matsuda, Takashi; Goto, Takaharu; Ishida, Yuichi; Ito, Teruaki; Ichikawa, Tetsuo

2017-01-01

To introduce a new clinical procedure for fabricating duplicates of complete dentures by bite pressure impression using digital technology, and to discuss its clinical significance. The denture is placed on a rotary table and the 3-dimensional form of the denture is digitized using a general-purpose handheld optical scanner. The duplicate denture is made of polylactic acid by a 3-dimensional printer using the 3-dimensional data. This procedure has the advantages of wasting less material, employing less human power, decreasing treatment time at the chair side, lowering the rates of contamination, and being readily fabricated at the time of the treatment visit. Copyright © 2016 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Developing a friendly I/O graphical interface for the integral transport CP2D computer code

International Nuclear Information System (INIS)

Constantin, M.

2002-01-01

The code CP 2 D design and developing involved the newest methods and techniques in the first flight collision probability (FFCP) calculations. These methods are strongly connected with the computer developing both in hardware and software. The code CP 2 D was developed in INR Pitesti, between 1997-2001. It is a transport code in the first flight collision probability formalism, able to treat exactly a lot of complicated geometry (such as CANDU clusters, TRIGA and PWR fuel assemblies). The first version CP 2 D1.0 was released in 1998. The second, CP 2 D2.0, was released in 1999 and uses a multistratified coolant model (MM) for CANDU loss of coolant accident analysis. The third version, CP 2 D3.0 (2000), have incorporated a generalized burning scheme. An user-friendly graphical interface was developed in 2001. It is intended to a rapid introduction of the input data and to extract the interest information from the output files. This information is directly converted into graphics and tables contained into a single MsWord document. The introduced input data are validated by the interface if the numerical, physical and mathematical restrictions are fulfilled. The user can see the representation of the model and can interactively modify the input data until the model is correct. The interface and the code were exhaustively documented and the obtained version was released as CP 2 D4.0. The version allows to a low experienced user to build the input files, to correct the possible errors and to extract the information of interest for the analyzed problem. The paper shows the interface as a useful concept for the upgrade of the classical codes. (author)

Correlates of Objective Social Isolation from Family and Friends among Older Adults.

Science.gov (United States)

Chatters, Linda M; Taylor, Harry Owen; Nicklett, Emily J; Taylor, Robert Joseph

2018-03-03

This study examined the correlates of objective social isolation from extended family members and friends among older adults. The analysis is based on the older adult sub-sample of the National Survey of American Life ( n = 1321). Multinomial logistic regression analyses examined race/ethnicity, demographics, functional health and family and friend network factors as correlates of objective isolation from family and friends. Only 4.47% of respondents were objectively isolated from both their extended family and friends, 10.82% were isolated from their friends, and 7.43% were isolated from their family members. Men were more likely to be objectively isolated from both family and friends and older adults who live with others were significantly more likely to be objectively isolated from their friends. When controlling for subjective social isolation, the two measures of functional health were significantly associated with objective social isolation. In particular, higher levels of self-care impairment decreased the risk of being objectively isolated from friends only, whereas higher mobility impairment was associated with an increased likelihood of being objectively isolated from friends only. Subjective evaluations of social isolation from family and friends were consistently associated with being objectively isolated from family and friends. There were no significant differences between African-Americans, Black Caribbeans and non-Hispanic Whites in objective isolation. These and other findings are discussed in detail.

Correlates of Objective Social Isolation from Family and Friends among Older Adults

Science.gov (United States)

Chatters, Linda M.; Taylor, Harry Owen; Taylor, Robert Joseph

2018-01-01

This study examined the correlates of objective social isolation from extended family members and friends among older adults. The analysis is based on the older adult sub-sample of the National Survey of American Life (n = 1321). Multinomial logistic regression analyses examined race/ethnicity, demographics, functional health and family and friend network factors as correlates of objective isolation from family and friends. Only 4.47% of respondents were objectively isolated from both their extended family and friends, 10.82% were isolated from their friends, and 7.43% were isolated from their family members. Men were more likely to be objectively isolated from both family and friends and older adults who live with others were significantly more likely to be objectively isolated from their friends. When controlling for subjective social isolation, the two measures of functional health were significantly associated with objective social isolation. In particular, higher levels of self-care impairment decreased the risk of being objectively isolated from friends only, whereas higher mobility impairment was associated with an increased likelihood of being objectively isolated from friends only. Subjective evaluations of social isolation from family and friends were consistently associated with being objectively isolated from family and friends. There were no significant differences between African-Americans, Black Caribbeans and non-Hispanic Whites in objective isolation. These and other findings are discussed in detail. PMID:29510504

Global Rural-Urban Mapping Project, Version 1 (GRUMPv1): Urban Extent Polygons, Revision 01

Data.gov (United States)

National Aeronautics and Space Administration — The primary output of the Global Rural Urban Mapping Project, Version 1 (GRUMPv1) are a series of grids representing estimated population counts and density for the...

Trigonometric version of quantum–classical duality in integrable systems

Directory of Open Access Journals (Sweden)

M. Beketov

2016-02-01

Full Text Available We extend the quantum–classical duality to the trigonometric (hyperbolic case. The duality establishes an explicit relationship between the classical N-body trigonometric Ruijsenaars–Schneider model and the inhomogeneous twisted XXZ spin chain on N sites. Similarly to the rational version, the spin chain data fixes a certain Lagrangian submanifold in the phase space of the classical integrable system. The inhomogeneity parameters are equal to the coordinates of particles while the velocities of classical particles are proportional to the eigenvalues of the spin chain Hamiltonians (residues of the properly normalized transfer matrix. In the rational version of the duality, the action variables of the Ruijsenaars–Schneider model are equal to the twist parameters with some multiplicities defined by quantum (occupation numbers. In contrast to the rational version, in the trigonometric case there is a splitting of the spectrum of action variables (eigenvalues of the classical Lax matrix. The limit corresponding to the classical Calogero–Sutherland system and quantum trigonometric Gaudin model is also described as well as the XX limit to free fermions.

Trigonometric version of quantum–classical duality in integrable systems

Energy Technology Data Exchange (ETDEWEB)

Beketov, M., E-mail: beketov@phystech.edu [MIPT, Inststitutskii per. 9, 141700, Dolgoprudny, Moscow region (Russian Federation); Liashyk, A., E-mail: a.liashyk@gmail.com [National Research University Higher School of Economics, Myasnitskaya str. 20, 101000, Moscow (Russian Federation); BITP, Metrolohichna str. 14-b, 03680, Kiev (Ukraine); Zabrodin, A., E-mail: zabrodin@itep.ru [National Research University Higher School of Economics, Myasnitskaya str. 20, 101000, Moscow (Russian Federation); Institute of Biochemical Physics, Kosygina str. 4, 119991, Moscow (Russian Federation); ITEP, Bolshaya Cheremushkinskaya str. 25, 117218, Moscow (Russian Federation); Zotov, A., E-mail: zotov@mi.ras.ru [Steklov Mathematical Institute, RAS, Gubkina str. 8, 119991, Moscow (Russian Federation); ITEP, Bolshaya Cheremushkinskaya str. 25, 117218, Moscow (Russian Federation); MIPT, Inststitutskii per. 9, 141700, Dolgoprudny, Moscow region (Russian Federation)

2016-02-15

We extend the quantum–classical duality to the trigonometric (hyperbolic) case. The duality establishes an explicit relationship between the classical N-body trigonometric Ruijsenaars–Schneider model and the inhomogeneous twisted XXZ spin chain on N sites. Similarly to the rational version, the spin chain data fixes a certain Lagrangian submanifold in the phase space of the classical integrable system. The inhomogeneity parameters are equal to the coordinates of particles while the velocities of classical particles are proportional to the eigenvalues of the spin chain Hamiltonians (residues of the properly normalized transfer matrix). In the rational version of the duality, the action variables of the Ruijsenaars–Schneider model are equal to the twist parameters with some multiplicities defined by quantum (occupation) numbers. In contrast to the rational version, in the trigonometric case there is a splitting of the spectrum of action variables (eigenvalues of the classical Lax matrix). The limit corresponding to the classical Calogero–Sutherland system and quantum trigonometric Gaudin model is also described as well as the XX limit to free fermions.

A streamlined artificial variable free version of simplex method.

Directory of Open Access Journals (Sweden)

Syed Inayatullah

Full Text Available This paper proposes a streamlined form of simplex method which provides some great benefits over traditional simplex method. For instance, it does not need any kind of artificial variables or artificial constraints; it could start with any feasible or infeasible basis of an LP. This method follows the same pivoting sequence as of simplex phase 1 without showing any explicit description of artificial variables which also makes it space efficient. Later in this paper, a dual version of the new method has also been presented which provides a way to easily implement the phase 1 of traditional dual simplex method. For a problem having an initial basis which is both primal and dual infeasible, our methods provide full freedom to the user, that whether to start with primal artificial free version or dual artificial free version without making any reformulation to the LP structure. Last but not the least, it provides a teaching aid for the teachers who want to teach feasibility achievement as a separate topic before teaching optimality achievement.

A streamlined artificial variable free version of simplex method.

Science.gov (United States)

Inayatullah, Syed; Touheed, Nasir; Imtiaz, Muhammad

2015-01-01

This paper proposes a streamlined form of simplex method which provides some great benefits over traditional simplex method. For instance, it does not need any kind of artificial variables or artificial constraints; it could start with any feasible or infeasible basis of an LP. This method follows the same pivoting sequence as of simplex phase 1 without showing any explicit description of artificial variables which also makes it space efficient. Later in this paper, a dual version of the new method has also been presented which provides a way to easily implement the phase 1 of traditional dual simplex method. For a problem having an initial basis which is both primal and dual infeasible, our methods provide full freedom to the user, that whether to start with primal artificial free version or dual artificial free version without making any reformulation to the LP structure. Last but not the least, it provides a teaching aid for the teachers who want to teach feasibility achievement as a separate topic before teaching optimality achievement.

Preparation, characterization and antibacterial effects of eco-friendly ...

African Journals Online (AJOL)

Purpose: To synthesize and characterize eco-friendly gold nanorods (Au-NRs) and to assess their effects against two bacterial strains. Methods: Synthesis of eco-friendly gold nanorods was done from an aqueous solution of chloroauric acid and cetyltrimethylammonium bromide by mixing Olea europaea fruit and Acacia ...

Daily well-being of older adults with friends and family.

Science.gov (United States)

Larson, R; Mannell, R; Zuzanek, J

1986-06-01

Family members are the major source of physical and emotional support for older adults, yet researchers suggest that friendships have a stronger bearing on subjective well-being. In this research we sought an explanation for this inconsistency in older adults' immediate experiences with friends. Retired adults provided self-reports on their subjective states at random moments during a typical week. Analyses of these reports confirmed the prediction that older adults have more favorable experiences with their friends than with family members. The difference is partly attributable to the greater frequency of active leisure activities with friends, but is also due to unique qualities of interactions with friends that facilitate transcendence of mundane daily realities. We propose that friends provide an immediate situation of openness, reciprocity, and positive feedback that engenders enjoyment and subjectively meaningful exchanges.

Perceptions of friendship among youth with distressed friends.

Science.gov (United States)

Hill, Erin N; Swenson, Lance P

2014-02-01

This cross-sectional study examined the relationship between a friend's level of internalizing distress and the focal child's perceptions of friendship amongst 5th, 8th, and 11th grade youth. Participants completed the Youth Self-Report to assess internalizing distress and measures assessing perceptions of friendship quality, social support, and self-disclosure within reciprocal, same-sex friendship dyads. Results indicated that youth with friends experiencing low levels of internalizing distress reported poorer friendship quality and decreased levels of social support and self-disclosure within the friendship compared to youth with friends experiencing average or high internalizing distress. In a second set of analyses controlling for the focal child's own internalizing symptoms, gender, and age, friend's level of internalizing distress remained a significant, unique predictor of target participants' self-disclosure about their own problems within the friendship. The findings suggest that a mild degree of internalizing distress may enhance, rather than harm, friendships amongst youth.

Green hypocrisy? Environmental attitudes and residential space heating expenditure

OpenAIRE

Traynor, Laura; Lange, Ian A.; Moro, Mirko

2012-01-01

In the UK, the largest proportion of household energy use is for space heating. Popular media make claims of a green hypocrisy: groups which have the strongest attitude towards the environment have the highest emissions. This study examines whether environmental attitudes and behaviours are associated with space heating energy use using data from the British Household Panel Survey. Results find that environmentally friendly attitudes generally do not lead to lower heating expenditures though ...

Handheld skin printer: in situ formation of planar biomaterials and tissues.

Science.gov (United States)

Hakimi, Navid; Cheng, Richard; Leng, Lian; Sotoudehfar, Mohammad; Ba, Phoenix Qing; Bakhtyar, Nazihah; Amini-Nik, Saeid; Jeschke, Marc G; Günther, Axel

2018-05-15

We present a handheld skin printer that enables the in situ formation of biomaterial and skin tissue sheets of different homogeneous and architected compositions. When manually positioned above a target surface, the compact instrument (weight <0.8 kg) conformally deposits a biomaterial or tissue sheet from a microfluidic cartridge. Consistent sheet formation is achieved by coordinating the flow rates at which bioink and cross-linker solution are delivered, with the speed at which a pair of rollers actively translate the cartridge along the surface. We demonstrate compatibility with dermal and epidermal cells embedded in ionically cross-linkable biomaterials (e.g., alginate), and enzymatically cross-linkable proteins (e.g., fibrin), as well as their mixtures with collagen type I and hyaluronic acid. Upon rapid crosslinking, biomaterial and skin cell-laden sheets of consistent thickness, width and composition were obtained. Sheets deposited onto horizontal, agarose-coated surfaces were used for physical and in vitro characterization. Proof-of-principle demonstrations for the in situ formation of biomaterial sheets in murine and porcine excisional wound models illustrate the capacity of depositing onto inclined and compliant wound surfaces that are subject to respiratory motion. We expect the presented work will enable the in situ delivery of a wide range of different cells, biomaterials, and tissue adhesives, as well as the in situ fabrication of spatially organized biomaterials, tissues, and biohybrid structures.

Polish Version of the Neighbourhood Environment Walkability Scale (NEWS-Poland).

Science.gov (United States)

Jaśkiewicz, Michał; Besta, Tomasz

2016-11-04

The characteristics of built environments are the subject of intense consideration in the search for solutions to promote wellbeing and a higher quality of life among the inhabitants of cities. Walkability, defined as the extent to which the built environment is friendly to living and fulfilling the needs of the area, has become an important concept in sustainable urban design, public health and environmental psychology. This study systematically adapted the Neighbourhood Environment Walkability Scale (NEWS) for Poland, and evaluated the construct validity aspects of the adapted version among Polish adults. A total sample of 783 participants from a TriCity (Trójmiasto) agglomeration completed the adapted version of the NEWS. Smaller extracted samples of the participants also completed wellbeing related scales, including self-efficacy, local identity and distance to city centre measures. It was expected that various districts of Gdańsk would differ in terms of walkability. The confirmatory factor analysis showed satisfactory goodness-of-fit statistics and factor loadings corresponding to the proposed original factor structure. According to the predictions, the NEWS subscales correlated with the self-efficacy, local identity and wellbeing related measures. In addition, the comparisons between the neighbourhoods of Gdańsk also showed a predictable pattern of results. Overall, the NEWS demonstrated satisfactory measurement properties, and may be useful in the evaluation of the built environment in Poland.

Accommodating life sciences on the Space Station

Science.gov (United States)

Arno, Roger D.

1987-01-01

The NASA Ames Research Center Biological Research Project (BRP) is responsible for identifying and accommodating high priority life science activities, utilizing nonhuman specimens, on the Space Station and is charged to bridge the gap between the science community and the Space Station Program. This paper discusses the approaches taken by the BRP in accomodating these research objectives to constraints imposed by the Space Station System, while maintaining a user-friendly environment. Consideration is given to the particular research disciplines which are given priority, the science objectives in each of these disciplines, the functions and activities required by these objectives, the research equipment, and the equipment suits. Life sciences programs planned by the Space Station participating partners (USA, Europe, Japan, and Canada) are compared.

Moral intensity and climate-friendly food choices.

Science.gov (United States)

Mäkiniemi, Jaana-Piia; Vainio, Annukka

2013-07-01

By changing individual food consumption patterns, it might be possible to reduce greenhouse gas emissions associated with climate change. The aim of the current study was to examine how perceptions of the moral intensity of climate change are related to climate friendly-food choices. The participants were 350 Finnish university students in the social and behavioral sciences who completed a questionnaire during class. The results indicated that moral perceptions mainly affected the moral evaluation and intentions to make climate-friendly food choices. We suggest that the results can be used to promote climate-friendly food choices, for example, by increasing the recognition of climate change as a moral imperative and by combining environmental motives with other relevant food choice motives. Copyright © 2013 Elsevier Ltd. All rights reserved.

Global Precipitation Climatology Project (GPCP) - Monthly, Version 2.2 (Version Superseded)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Version 2.2 of the dataset has been superseded by a newer version. Users should not use version 2.2 except in rare cases (e.g., when reproducing previous studies...

Corrosion-Activated Micro-Containers for Environmentally Friendly Corrosion Protective Coatings

Science.gov (United States)

Li, Wenyan; Buhrow, J. W.; Zhang, X.; Johnsey, M. N.; Pearman, B. P.; Jolley, S. T.; Calle, L. M.

2016-01-01

This work concerns the development of environmentally friendly encapsulation technology, specifically designed to incorporate corrosion indicators, inhibitors, and self-healing agents into a coating, in such a way that the delivery of the indicators and inhibitors is triggered by the corrosion process, and the delivery of self-healing agents is triggered by mechanical damage to the coating. Encapsulation of the active corrosion control ingredients allows the incorporation of desired autonomous corrosion control functions such as: early corrosion detection, hidden corrosion detection, corrosion inhibition, and self-healing of mechanical damage into a coating. The technology offers the versatility needed to include one or several corrosion control functions into the same coating.The development of the encapsulation technology has progressed from the initial proof-of-concept work, in which a corrosion indicator was encapsulated into an oil-core (hydrophobic) microcapsule and shown to be delivered autonomously, under simulated corrosion conditions, to a sophisticated portfolio of micro carriers (organic, inorganic, and hybrid) that can be used to deliver a wide range of active corrosion ingredients at a rate that can be adjusted to offer immediate as well as long-term corrosion control. The micro carriers have been incorporated into different coating formulas to test and optimize the autonomous corrosion detection, inhibition, and self-healing functions of the coatings. This paper provides an overview of progress made to date and highlights recent technical developments, such as improved corrosion detection sensitivity, inhibitor test results in various types of coatings, and highly effective self-healing coatings based on green chemistry. The NASA Kennedy Space Centers Corrosion Technology Lab at the Kennedy Space Center in Florida, U.S.A. has been developing multifunctional smart coatings based on the microencapsulation of environmentally friendly corrosion

Computable Frames in Computable Banach Spaces

Directory of Open Access Journals (Sweden)

S.K. Kaushik

2016-06-01

Full Text Available We develop some parts of the frame theory in Banach spaces from the point of view of Computable Analysis. We define computable M-basis and use it to construct a computable Banach space of scalar valued sequences. Computable Xd frames and computable Banach frames are also defined and computable versions of sufficient conditions for their existence are obtained.

Friends' Organizations: The Supportive Element Essential to Libraries.

Science.gov (United States)

Progar, Dorothy

Reviewed are the history and public relations, financial and service roles of lay "Friends of the Library" groups. Programs and techniques useful in the pursuit of these roles are suggested. Guidelines for a constitution, fee schedule, and administrative structure plus a bibliography give potential friends organizations help in…

Abelian properties of Anick spaces

CERN Document Server

Gray, Brayton

2017-01-01

Anick spaces are closely connected with both EHP sequences and the study of torsion exponents. In addition they refine the secondary suspension and enter unstable periodicity. This work describes their H-space properties as well as universal properties. Techniques include a new kind on Whitehead product defined for maps out of co-H spaces, calculations in an additive category that lies between the unstable category and the stable category, and a controlled version of the extension theorem of Gray and Theriault (Geom. Topol. 14 (2010), no. 1, 243-275).

Nuclear-electric power in space

International Nuclear Information System (INIS)

Truscello, V.C.; Davis, H.S.

1984-01-01

Because direct-broadcast satellites, air-traffic-control radar satellites, industrial processing on subsequent versions of the space station, and long range excursions to other planets using nuclear-electric propulsion systems, all space missions for which current power-supply systems are not sufficient. NASA and the DOE therefore have formed a joint program to develop the technology required for nuclear-reactor space power plants. After investigating potential space missions in the given range, the project will develop the technology to build such systems. High temperatures pose problems, ''hot shoes'' and ''cold shoes'', a Stirling engine dynamic system, and critical heat-transfer problems are all discussed. The nuclear reactor system for space as now envisioned is schematicized

Omicron space habitat—research stage II

Science.gov (United States)

Doule, Ondřej; Šálený, Vratislav; Hérin, Benoît; Rousek, Tomáš

2012-01-01

The design presented in this paper is in response to the revolution in private space activities, the increasing public interest in commercial flights to space and the utilization of structures such as space hotels or private orbital habitats. The baseline for the Omicron design concept is the Russian Salyut derived space station module. Salyut was the first space station to orbit the Earth. Its unique design and technical features were what made the development of space stations Salyut 1-7, MIR and the International Space Station (ISS) Zwezda service module possible. Due to its versatility and the reliable operating launch vehicle Proton, this space module series has the potential to be adapted for space hotel development. This paper proposes a conceptual design of the space habitat called Omicron, with particular focus on interior design for the microgravity environment. The Omicron concepts address the needs of space tourism with a strong emphasis on the safety and comfort of the spaceflight participants. The Omicron habitat supports three inhabitants in nominal conditions (e.g., two passengers and one astronaut). The habitat provides a flexible interior, facilities and spaces dynamically transforming in order to accommodate various types of activities, which will be performed in an organically formed interior supporting spatial orientation and movement in microgravity. The future development potential of Omicron is also considered. The baseline version is composed solely of one rigid module with an inverted cupola for observations. An alternative version offers more space using an inflatable structure. Finally, a combination of multiple Omicron modules enables the creation of a larger orbital habitat. The Omicron's subsystems support a few days visit by trained passengers. The transport to the habitat would be provided e.g., by the Soyuz TMA spacecraft carried by the Soyuz launch vehicle in the early stage of Omicron's development, before a fully reusable

Three friendly walkers

Science.gov (United States)

Jensen, Iwan

2017-01-01

More than 15 years ago Guttmann and Vöge (2002 J. Stat. Plan. Inference 101 107), introduced a model of friendly walkers. Since then it has remained unsolved. In this paper we provide the exact solution to a closely allied model which essentially only differs in the boundary conditions. The exact solution is expressed in terms of the reciprocal of the generating function for vicious walkers which is a D-finite function. However, ratios of D-finite functions are inherently not D-finite and in this case we prove that the friendly walkers generating function is the solution to a non-linear differential equation with polynomial coefficients, it is in other words D-algebraic. We find using numerically exact calculations a conjectured expression for the generating function of the original model as a ratio of a D-finite function and the generating function for vicious walkers. We obtain an expression for this D-finite function in terms of a {{}2}{{F}1} hypergeometric function with a rational pullback and its first and second derivatives. Dedicated to Tony Guttmann on the occasion of his 70th birthday.

The Johnson Space Center Management Information Systems (JSCMIS). 1: Requirements Definition and Design Specifications for Versions 2.1 and 2.1.1. 2: Documented Test Scenario Environments. 3: Security Design and Specifications

Science.gov (United States)

1986-01-01

The Johnson Space Center Management Information System (JSCMIS) is an interface to computer data bases at NASA Johnson which allows an authorized user to browse and retrieve information from a variety of sources with minimum effort. This issue gives requirements definition and design specifications for versions 2.1 and 2.1.1, along with documented test scenario environments, and security object design and specifications.

Climate-friendly Default Rules

DEFF Research Database (Denmark)

Sunstein, Cass R.; Reisch, Lucia A.

. The underlying reasons include the power of suggestion; inertia and procrastination; and loss aversion. If well-chosen, climate-friendly defaults are likely to have large effects in reducing the economic and environmental harms associated with various products and activities. In deciding whether to establish...

Space Qualified, Radiation Hardened, Dense Monolithic Flash Memory, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — Space Micro proposes to build a radiation hardened by design (RHBD) flash memory, using a modified version of our RH-eDRAM Memory Controller to solve all the single...

Friends First? The Peer Network Origins of Adolescent Dating

Science.gov (United States)

Kreager, Derek A.; Molloy, Lauren E.; Moody, James; Feinberg, Mark E.

2015-01-01

The proximity of dating partners in peer friendship networks has important implications for the diffusion of health-risk behaviors and adolescent social development. We derive two competing hypotheses for the friendship-romance association. The first predicts that daters are proximally positioned in friendship networks prior to dating and that opposite-gender friends are likely to transition to dating. The second predicts that dating typically crosses group boundaries and opposite-gender friends are unlikely to later date. We test these hypotheses with longitudinal friendship data for 626 9th grade PROSPER heterosexual dating couples. Results primarily support the second hypothesis: romantic partners are unlikely to be friends in the previous year or share the same cohesive subgroup, and opposite-gender friends are unlikely to transition into dating. PMID:27134511

PARMELA-B A new version of PARMELA with coherent synchrotron radiation effects and a finite difference space charge routine

CERN Document Server

Koltenbah, B E C; Greegor, R B; Dowell, D H

2002-01-01

Recent interest in advanced laser light sources has stimulated development of accelerator systems of intermediate beam energy, 100-200 MeV, and high charge, 1-10 nC, for high power FEL applications and high energy, 1-2 GeV, high charge, SASE-FEL applications. The current generation of beam transport codes which were developed for high-energy, low-charge beams with low self-fields are inadequate to address this energy and charge regime, and better computational tools are required to accurately calculate self-fields. To that end, we have developed a new version of PARMELA, named PARMELA_B and written in Fortran 95, which includes a coherent synchrotron radiation (CSR) routine and an improved, generalized space charge (SC) routine. An electron bunch is simulated by a collection of macro-particles, which traverses a series of beam line elements. At each time step through the calculation, the momentum of each particle is updated due to the presence of external and self- fields. The self-fields are due to CSR and S...

3D print of polymer bonded rare-earth magnets, and 3D magnetic field scanning with an end-user 3D printer

Science.gov (United States)

Huber, C.; Abert, C.; Bruckner, F.; Groenefeld, M.; Muthsam, O.; Schuschnigg, S.; Sirak, K.; Thanhoffer, R.; Teliban, I.; Vogler, C.; Windl, R.; Suess, D.

2016-10-01

3D print is a recently developed technique, for single-unit production, and for structures that have been impossible to build previously. The current work presents a method to 3D print polymer bonded isotropic hard magnets with a low-cost, end-user 3D printer. Commercially available isotropic NdFeB powder inside a PA11 matrix is characterized, and prepared for the printing process. An example of a printed magnet with a complex shape that was designed to generate a specific stray field is presented, and compared with finite element simulation solving the macroscopic Maxwell equations. For magnetic characterization, and comparing 3D printed structures with injection molded parts, hysteresis measurements are performed. To measure the stray field outside the magnet, the printer is upgraded to a 3D magnetic flux density measurement system. To skip an elaborate adjusting of the sensor, a simulation is used to calibrate the angles, sensitivity, and the offset of the sensor. With this setup, a measurement resolution of 0.05 mm along the z-axes is achievable. The effectiveness of our calibration method is shown. With our setup, we are able to print polymer bonded magnetic systems with the freedom of having a specific complex shape with locally tailored magnetic properties. The 3D scanning setup is easy to mount, and with our calibration method we are able to get accurate measuring results of the stray field.

The Importance of Friends in Autobiographical Memory

DEFF Research Database (Denmark)

Antalikova, Radka; Hansen, Tia G. B.; Gulbrandsen, Knut Arild

often rehearsed, family memories that were old and rarely rehearsed, and school memories that were in between on both variables. This supports theories of friendship as the primary social context for adolescent development. Moreover, content analysis found friend memories to mention others more often......Relatedness is a complex issue and it has been argued that developmental perspectives should complement cross-cultural comparisons. We noticed that cross-cultural studies of autobiographical memories tend to focus on early childhood and thus family, leaving the role of friends and school less...... explored. Thus, we asked adolescent school-goers who still lived with their parents for a meaningful memory from each of the settings family, school, and friendship. In both samples analyzed so far (Norwegians, N=22, and Slovaks, N=40) participants chose friend memories that were recent and reportedly...

The three versions of distributional chaos

International Nuclear Information System (INIS)

Balibrea, F.; Smital, J.; Stefankova, M.

2005-01-01

The notion of distributional chaos was introduced by Schweizer and Smital [Trans. Amer. Math. Soc. 344 (1994) 737] for continuous maps of the interval. However, it turns out that, for continuous maps of a compact metric space three mutually nonequivalent versions of distributional chaos, DC1-DC3, can be considered. In this paper we consider the weakest one, DC3. We show that DC3 does not imply chaos in the sense of Li and Yorke. We also show that DC3 is not invariant with respect to topological conjugacy. In other words, there are lower and upper distribution functions Φ xy and Φxy* generated by a continuous map f of a compact metric space (M, ρ) such that Φxy*(t)>Φxy(t) for all t in an interval. However, f on the same space M, but with a metric ρ' generating the same topology as ρ is no more DC3.Recall that, contrary to this, either DC1 or DC2 is topological conjugacy invariant and implies Li and Yorke chaos (cf. [Chaos, Solitons and Fractals 21 (2004) 1125])

Does the Gap in Family-Friendly Policies Drive the Family Gap?

DEFF Research Database (Denmark)

Nielsen, Helena Skyt; Simonsen, Marianne; Verner, Mette

2004-01-01

Segregation of the labour market into a family-friendly and a non-family-friendly sector implies that women self-select into sectors depending on institutional constraints, preferences for family-friendly working conditions and expected wage differences. We take this sector dimension into account...

A new technique for the deposition of standard solutions in total reflection X-ray fluorescence spectrometry (TXRF) using pico-droplets generated by inkjet printers and its applicability for aerosol analysis with SR-TXRF

International Nuclear Information System (INIS)

Fittschen, U.E.A.; Hauschild, S.; Amberger, M.A.; Lammel, G.; Streli, C.; Foerster, S.; Wobrauschek, P.; Jokubonis, C.; Pepponi, G.; Falkenberg, G.; Broekaert, J.A.C.

2006-01-01

A new technique for the deposition of standard solutions on particulate aerosol samples using pico-droplets for elemental determinations with total reflection X-ray fluorescence spectrometry (TXRF) is described. It enables short analysis times without influencing the sample structure and avoids time consuming scanning of the sample with the exciting beam in SR-TXRF analysis. Droplets of picoliter volume (∼ 5-130 pL) were generated with commercially available and slightly modified inkjet printers operated with popular image processing software. The size of the dried droplets on surfaces of different polarity namely silicone coated and untreated quartz reflectors, was determined for five different printer types and ten different cartridge types. The results show that droplets generated by inkjet printers are between 50 and 200 μm in diameter (corresponding to volumes of 5 to 130 pL) depending on the cartridge type, which is smaller than the width of the synchrotron beam used in the experiments (< 1 mm at an energy of 17 keV at the beamline L at HASYLAB, Hamburg). The precision of the printing of a certain amount of a single element standard solution was found to be comparable to aliquoting with micropipettes in TXRF, where for 2.5 ng of cobalt relative standard deviations of 12% are found. However, it could be shown that the printing of simple patterns is possible, which is important when structured samples have to be analysed

Global Historical Climatology Network (GHCN), Version 1 (Version Superseded)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Please note, this dataset has been superseded by a newer version (see below). Users should not use this version except in rare cases (e.g., when reproducing previous...

A user-friendly web portal for T-Coffee on supercomputers

Directory of Open Access Journals (Sweden)

Koetsier Jos

2011-05-01

Full Text Available Abstract Background Parallel T-Coffee (PTC was the first parallel implementation of the T-Coffee multiple sequence alignment tool. It is based on MPI and RMA mechanisms. Its purpose is to reduce the execution time of the large-scale sequence alignments. It can be run on distributed memory clusters allowing users to align data sets consisting of hundreds of proteins within a reasonable time. However, most of the potential users of this tool are not familiar with the use of grids or supercomputers. Results In this paper we show how PTC can be easily deployed and controlled on a super computer architecture using a web portal developed using Rapid. Rapid is a tool for efficiently generating standardized portlets for a wide range of applications and the approach described here is generic enough to be applied to other applications, or to deploy PTC on different HPC environments. Conclusions The PTC portal allows users to upload a large number of sequences to be aligned by the parallel version of TC that cannot be aligned by a single machine due to memory and execution time constraints. The web portal provides a user-friendly solution.

A Forever Friend%永远的朋友

Institute of Scientific and Technical Information of China (English)

无

2007-01-01

@@ A friend walk in when the rest of the world walks out. Sometimes in life, You find a special friend; Someone who changes your life just by being part of it. Someone who makes you laugh until you can't stop; Someone who makes you believe that there really is good in the world.

A fast algorithm for identifying friends-of-friends halos

Science.gov (United States)

Feng, Y.; Modi, C.

2017-07-01

We describe a simple and fast algorithm for identifying friends-of-friends features and prove its correctness. The algorithm avoids unnecessary expensive neighbor queries, uses minimal memory overhead, and rejects slowdown in high over-density regions. We define our algorithm formally based on pair enumeration, a problem that has been heavily studied in fast 2-point correlation codes and our reference implementation employs a dual KD-tree correlation function code. We construct features in a hierarchical tree structure, and use a splay operation to reduce the average cost of identifying the root of a feature from O [ log L ] to O [ 1 ] (L is the size of a feature) without additional memory costs. This reduces the overall time complexity of merging trees from O [ L log L ] to O [ L ] , reducing the number of operations per splay by orders of magnitude. We next introduce a pruning operation that skips merge operations between two fully self-connected KD-tree nodes. This improves the robustness of the algorithm, reducing the number of merge operations in high density peaks from O [δ2 ] to O [ δ ] . We show that for cosmological data set the algorithm eliminates more than half of merge operations for typically used linking lengths b ∼ 0 . 2 (relative to mean separation). Furthermore, our algorithm is extremely simple and easy to implement on top of an existing pair enumeration code, reusing the optimization effort that has been invested in fast correlation function codes.

Perceived and desired facilitativeness of one's closest friend, need for approval and self-esteem.

Science.gov (United States)

Cramer, D

1993-03-01

The hypothesis that the positive association between self-esteem and the perceived facilitativeness of one's closest friend can be explained by the presumed greater desire of low self-esteem individuals for a facilitative relationship was not confirmed in 262 16-17-year-old females, who completed the Rosenberg (1965) Self-Esteem Scale and a shortened version of the Barrett-Lennard (1964) Relationship Inventory. Although desired facilitativeness correlated significantly positively with self-esteem, the correlation between perceived facilitativeness and self-esteem remained significantly positive when desired facilitativeness was partialled out. The further prediction that the correlation between perceived facilitativeness and self-esteem would be more positive for those scoring higher on the Jones' (1969) Need for Approval Scale was also not confirmed. The opposite result was obtained in that this correlation was significantly positive for those with low need for approval but not for those with a high need.

Development of a phantom 'Canis Morphic' using 3D printer for use in dosimetry in veterinary radiation therapy

International Nuclear Information System (INIS)

Veneziani, Glauco Rogério

2017-01-01

The increase in human longevity caused a number of diseases with age; in contrast the advancement of medicine made possible the early diagnosis and treatment of several previously incurable diseases. This scenario is also important for domestic animals (dogs and cats - PETs) that have doubled their life expectancy in recent decades, a fact that humans took centuries to reach. Like humans, this increase in animal longevity was accompanied by age-related diseases, including cancer. One of the therapies currently used in the treatment of cancer is radiation therapy, a technique that uses ionizing radiation to destroy tumor cells (target volume) with minimal impairment to healthy surrounding tissues (organs at risk). This technique requires periodic quality control testing, including dosimetry with the use of tissue-equivalent phantoms, in order to verify the dose of radiation received by the patient being treated and to compare it subsequently with the calculated radiation dose by the treatment planning system. The rapid expansion of the 3D printer opened the way for a health revolution. planning for the spatial location and mapping of the isodose curves, thus realizing a more personalized planning for each radiation field, besides the preparation of dental implants, customization of prostheses and build of bolus. This work aimed has designed and developed a simulator object called 'Canis Morphic' using a 3D printer and tissue-equivalent materials to perform quality control and dose optimization tests in the area of Radiation therapy in animals (dogs). The results obtained demonstrated be promising in the area of development of phantoms by 3D printing, with materials of low cost, for application in quality control in Veterinary Radiation therapy. (author)