Literature study of source term research for PWRs

International Nuclear Information System (INIS)

Sponton, L.L.; NiIsson, Lars

2001-04-01

A literature survey has been carried out in support of ongoing source term calculations with the MELCOR code of some severe accident scenarios for the Swedish Ringhals 2 pressurised water reactor (PWR). The research in the field of severe accidents in power reactors and the source term for subsequent release of radioisotopes was intensified after the Harrisburg accident and has produced a large amount of reports and papers. This survey was therefore limited to research concerning PWR type of reactors and with emphasis on papers related to MELCOR code development. A background is given, relating to some historic documents, and then more recent research after 1990 is reviewed. Of special interest is the ongoing PMbus-programme which is creating new and important results of benefit to the code development and validation of, among others, the MELCOR code. It is concluded that source term calculations involve simulation of many interacting complex physical phenomena, which result in large uncertainties The research has, however, over the years led to considerable improvements Thus has the uncertainty in source term predictions been reduced one to two orders of magnitude from the simpler codes in the early 1980-s to the more realistic codes of today, like MELCOR

ITER task title - source term data, modelling, and analysis. ITER subtask no. S81TT05/5 (SEP 1-1). Global tritium source term analysis basis document. Subtask 1: operational tritium effluents and releases. Final report (1995 TASK)

International Nuclear Information System (INIS)

Kalyanam, K.M.

1996-06-01

This document represents the final report for the global tritium source term analysis task initiated in 1995. The report presents a room-by-room map/table at the subsystem level for the ITER tritium systems, identifying the major equipment, secondary containments, tritium release sources, duration/frequency of tritium releases and the release pathways. The chronic tritium releases during normal operation, as well as tritium releases due to routine maintenance of the Water Distillation Unit, Isotope Separation System and Primary and Secondary Heat Transport Systems, have been estimated for most of the subsystems, based on the IDR design, the Design Description Documents (April - Jun 1995 issues) and the design updates up to December 1995. The report also outlines the methodology and the key assumptions that are adopted in preparing the tritium release estimates. The design parameters for the ITER Basic Performance Phase (BPP) have been used in estimating the tritium releases shown in the room-by-room map/table. The tritium release calculations and the room-by-room map/table have been prepared in EXCEL, so that the estimates can be refined easily as the design evolves and more detailed information becomes available. (author). 23 refs., tabs

Accident source terms for boiling water reactors with high burnup cores.

Energy Technology Data Exchange (ETDEWEB)

Gauntt, Randall O.; Powers, Dana Auburn; Leonard, Mark Thomas

2007-11-01

The primary objective of this report is to provide the technical basis for development of recommendations for updates to the NUREG-1465 Source Term for BWRs that will extend its applicability to accidents involving high burnup (HBU) cores. However, a secondary objective is to re-examine the fundamental characteristics of the prescription for fission product release to containment described by NUREG-1465. This secondary objective is motivated by an interest to understand the extent to which research into the release and behaviors of radionuclides under accident conditions has altered best-estimate calculations of the integral response of BWRs to severe core damage sequences and the resulting radiological source terms to containment. This report, therefore, documents specific results of fission product source term analyses that will form the basis for the HBU supplement to NUREG-1465. However, commentary is also provided on observed differences between the composite results of the source term calculations performed here and those reflected NUREG-1465 itself.

Hazardous constituent source term. Revision 2

International Nuclear Information System (INIS)

1994-01-01

The Department of Energy (DOE) has several facilities that either generate and/or store transuranic (TRU)-waste from weapons program research and production. Much of this waste also contains hazardous waste constituents as regulated under Subtitle C of the Resource Conservation and Recovery Act (RCRA). Toxicity characteristic metals in the waste principally include lead, occurring in leaded rubber gloves and shielding. Other RCRA metals may occur as contaminants in pyrochemical salt, soil, debris, and sludge and solidified liquids, as well as in equipment resulting from decontamination and decommissioning activities. Volatile organic compounds (VOCS) contaminate many waste forms as a residue adsorbed on surfaces or occur in sludge and solidified liquids. Due to the presence of these hazardous constituents, applicable disposal regulations include land disposal restrictions established by Hazardous and Solid Waste Amendments (HSWA). The DOE plans to dispose of TRU-mixed waste from the weapons program in the Waste Isolation Pilot Plant (WIPP) by demonstrating no-migration of hazardous constituents. This paper documents the current technical basis for methodologies proposed to develop a post-closure RCRA hazardous constituent source term. For the purposes of demonstrating no-migration, the hazardous constituent source term is defined as the quantities of hazardous constituents that are available for transport after repository closure. Development of the source term is only one of several activities that will be involved in the no-migration demonstration. The demonstration will also include uncertainty and sensitivity analyses of contaminant transport

The Multimedia Environmental Pollutant Assessment System (MEPAS)reg-sign: Source-term release formulations

International Nuclear Information System (INIS)

Streile, G.P.; Shields, K.D.; Stroh, J.L.; Bagaasen, L.M.; Whelan, G.; McDonald, J.P.; Droppo, J.G.; Buck, J.W.

1996-11-01

This report is one of a series of reports that document the mathematical models in the Multimedia Environmental Pollutant Assessment System (MEPAS). Developed by Pacific Northwest National Laboratory for the US Department of Energy, MEPAS is an integrated impact assessment software implementation of physics-based fate and transport models in air, soil, and water media. Outputs are estimates of exposures and health risk assessments for radioactive and hazardous pollutants. Each of the MEPAS formulation documents covers a major MEPAS component such as source-term, atmospheric, vadose zone/groundwater, surface water, and health exposure/health impact assessment. Other MEPAS documentation reports cover the sensitivity/uncertainty formulations and the database parameter constituent property estimation methods. The pollutant source-term release component is documented in this report. MEPAS simulates the release of contaminants from a source, transport through the air, groundwater, surface water, or overland pathways, and transfer through food chains and exposure pathways to the exposed individual or population. For human health impacts, risks are computed for carcinogens and hazard quotients for noncarcinogens. MEPAS is implemented on a desktop computer with a user-friendly interface that allows the user to define the problem, input the required data, and execute the appropriate models for both deterministic and probabilistic analyses

Source terms: an investigation of uncertainties, magnitudes, and recommendations for research. [PWR; BWR

Energy Technology Data Exchange (ETDEWEB)

Levine, S.; Kaiser, G. D.; Arcieri, W. C.; Firstenberg, H.; Fulford, P. J.; Lam, P. S.; Ritzman, R. L.; Schmidt, E. R.

1982-03-01

The purpose of this document is to assess the state of knowledge and expert opinions that exist about fission product source terms from potential nuclear power plant accidents. This is so that recommendations can be made for research and analyses which have the potential to reduce the uncertainties in these estimated source terms and to derive improved methods for predicting their magnitudes. The main reasons for writing this report are to indicate the major uncertainties involved in defining realistic source terms that could arise from severe reactor accidents, to determine which factors would have the most significant impact on public risks and emergency planning, and to suggest research and analyses that could result in the reduction of these uncertainties. Source terms used in the conventional consequence calculations in the licensing process are not explicitly addressed.

Fission-product source terms

International Nuclear Information System (INIS)

Lorenz, R.A.

1981-01-01

This presentation consists of a review of fission-product source terms for light water reactor (LWR) fuel. A source term is the quantity of fission products released under specified conditions that can be used to calculate the consequences of the release. The source term usually defines release from breached fuel-rod cladding but could also describe release from the primary coolant system, the reactor containment shell, or the site boundary. The source term would be different for each locality, and the chemical and physical forms of the fission products could also differ

Accident source terms for Light-Water Nuclear Power Plants. Final report

International Nuclear Information System (INIS)

Soffer, L.; Burson, S.B.; Ferrell, C.M.; Lee, R.Y.; Ridgely, J.N.

1995-02-01

In 1962 tile US Atomic Energy Commission published TID-14844, ''Calculation of Distance Factors for Power and Test Reactors'' which specified a release of fission products from the core to the reactor containment for a postulated accident involving ''substantial meltdown of the core''. This ''source term'', tile basis for tile NRC's Regulatory Guides 1.3 and 1.4, has been used to determine compliance with tile NRC's reactor site criteria, 10 CFR Part 100, and to evaluate other important plant performance requirements. During the past 30 years substantial additional information on fission product releases has been developed based on significant severe accident research. This document utilizes this research by providing more realistic estimates of the ''source term'' release into containment, in terms of timing, nuclide types, quantities and chemical form, given a severe core-melt accident. This revised ''source term'' is to be applied to the design of future light water reactors (LWRs). Current LWR licensees may voluntarily propose applications based upon it

Design parameters and source terms: Volume 1, Design parameters: Revision 0

International Nuclear Information System (INIS)

1987-09-01

The Design Parameters and Source Terms Document was prepared in accordance with DOE request and to provide data for the environmental impact study to be performed in the future for the Deaf Smith County, Texas site for a nuclear waste repository in salt. This document updates a previous unpublished report to the level of the Site Characterization Plan - Conceptual Design Report, SCP-CDR. The previous unpublished SCC Study identified the data needs for the Environmental Assessment effort for seven possible salt repository sites

Consideration of emergency source terms for pebble-bed high temperature gas-cooled reactor

International Nuclear Information System (INIS)

Tao, Liu; Jun, Zhao; Jiejuan, Tong; Jianzhu, Cao

2009-01-01

Being the last barrier in the nuclear power plant defense-in-depth strategy, emergency planning (EP) is an integrated project. One of the key elements in this process is emergency source terms selection. Emergency Source terms for light water reactor (LWR) nuclear power plant (NPP) have been introduced in many technical documents, and advanced NPP emergency planning is attracting attention recently. Commercial practices of advanced NPP are undergoing in the world, pebble-bed high-temperature gas-cooled reactor (HTGR) power plant is under construction in China which is considered as a representative of advanced NPP. The paper tries to find some pieces of suggestion from our investigation. The discussion of advanced NPP EP will be summarized first, and then the characteristics of pebble-bed HTGR relating to EP will be described. Finally, PSA insights on emergency source terms selection and current pebble-bed HTGR emergency source terms suggestions are proposed

Review of the status of validation of the computer codes used in the severe accident source term reassessment study (BMI-2104)

International Nuclear Information System (INIS)

Kress, T.S.

1985-04-01

The determination of severe accident source terms must, by necessity it seems, rely heavily on the use of complex computer codes. Source term acceptability, therefore, rests on the assessed validity of such codes. Consequently, one element of NRC's recent efforts to reassess LWR severe accident source terms is to provide a review of the status of validation of the computer codes used in the reassessment. The results of this review is the subject of this document. The separate review documents compiled in this report were used as a resource along with the results of the BMI-2104 study by BCL and the QUEST study by SNL to arrive at a more-or-less independent appraisal of the status of source term modeling at this time

2011 Addendum to the SNL/NM SWEIS Supplemental Information Source Documents

Energy Technology Data Exchange (ETDEWEB)

Dimmick, Ross [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2014-12-01

This document contains updates to the Supplemental Information Sandia National Laboratories/New Mexico Site-Wide Environmental Impact Statement Source Documents that were developed in 2010. In general, this addendum provides calendar year 2010 data, along with changes or additions to text in the original documents.

Perspectives on source terms based on early research and development

International Nuclear Information System (INIS)

Pressesky, A.J.

1985-07-01

This report presents an overview of the key documentation of the research and development programs relevant to the source term issue which were undertaken by the Atomic Energy Commission between 1950 and 1970. The source term is taken to be the amount, composition (physical and chemical), and timing of the projected release of radioactivity to the environment in the hypothetical event of a severe reactor accident in a light water reactor of the type currently being licensed, built and operated. The objective is to illuminate and provide perspectives on (a) the maturity of the technical data base and the analytical methodology, (b) the extent to which remaining conservatisms can be applied to compensate for uncertainties, (c) the purpose for which the technology and methodology will be used, and (d) the need to keep problems and uncertainties in proper perspective. Comments that can provide some context for the difficult programmatic choices to be made are included, and technical considerations that may be inadequately applied or neglected in some current source term calculations were studied. This review has not uncovered any significant technical considerations that have been omitted or are being inadequately treated in current source term analyses, except perhaps the contribution made to in-containment aerosols by coolant comminution upon escape at pressure from the reactor coolant system. 11 refs

Synthesis document on the long time behavior of packages: operational document ''bituminous'' 2204

International Nuclear Information System (INIS)

Tiffreau, C.

2004-09-01

This document is realized in the framework of the law of 1991 on the radioactive wastes management. The 2004 synthesis document on long time behavior of bituminous sludges packages is constituted by two documents, the reference document and the operational document. This paper presents the operational model describing the water alteration of the packages and the associated radioelements release, as the gas term source and the swelling associated to the self-irradiation and the bituminous radiolysis. (A.L.B.)

New Source Term Model for the RESRAD-OFFSITE Code Version 3

Energy Technology Data Exchange (ETDEWEB)

Yu, Charley [Argonne National Lab. (ANL), Argonne, IL (United States); Gnanapragasam, Emmanuel [Argonne National Lab. (ANL), Argonne, IL (United States); Cheng, Jing-Jy [Argonne National Lab. (ANL), Argonne, IL (United States); Kamboj, Sunita [Argonne National Lab. (ANL), Argonne, IL (United States); Chen, Shih-Yew [Argonne National Lab. (ANL), Argonne, IL (United States)

2013-06-01

This report documents the new source term model developed and implemented in Version 3 of the RESRAD-OFFSITE code. This new source term model includes: (1) "first order release with transport" option, in which the release of the radionuclide is proportional to the inventory in the primary contamination and the user-specified leach rate is the proportionality constant, (2) "equilibrium desorption release" option, in which the user specifies the distribution coefficient which quantifies the partitioning of the radionuclide between the solid and aqueous phases, and (3) "uniform release" option, in which the radionuclides are released from a constant fraction of the initially contaminated material during each time interval and the user specifies the duration over which the radionuclides are released.

PLOTLIB: a computerized nuclear waste source-term library storage and retrieval system

International Nuclear Information System (INIS)

Marshall, J.R.; Nowicki, J.A.

1978-01-01

The PLOTLIB code was written to provide computer access to the Nuclear Waste Source-Term Library for those users with little previous computer programming experience. The principles of user orientation, quick accessibility, and versatility were extensively employed in the development of the PLOTLIB code to accomplish this goal. The Nuclear Waste Source-Term Library consists of 16 ORIGEN computer runs incorporating a wide variety of differing light water reactor (LWR) fuel cycles and waste streams. The typical isotopic source-term data consist of information on watts, curies, grams, etc., all of which are compiled as a function of time after reactor discharge and unitized on a per metric ton heavy metal basis. The information retrieval code, PLOTLIB, is used to process source-term information requests into computer plots and/or user-specified output tables. This report will serve both as documentation of the current data library and as an operations manual for the PLOTLIB computer code. The accompanying input description, program listing, and sample problems make this code package an easily understood tool for the various nuclear waste studies under way at the Office of Waste Isolation

How Do Open Source Communities Document Software Architecture: An Exploratory Survey

NARCIS (Netherlands)

Ding, W.; Liang, P.; Tang, A.; Van Vliet, H.; Shahin, M.

2014-01-01

Software architecture (SA) documentation provides a blueprint of a software-intensive system for the communication between stakeholders about the high-level design of the system. In open source software (OSS) development, a lack of SA documentation may hinder the use and further development of OSS,

Embedding Term Similarity and Inverse Document Frequency into a Logical Model of Information Retrieval.

Science.gov (United States)

Losada, David E.; Barreiro, Alvaro

2003-01-01

Proposes an approach to incorporate term similarity and inverse document frequency into a logical model of information retrieval. Highlights include document representation and matching; incorporating term similarity into the measure of distance; new algorithms for implementation; inverse document frequency; and logical versus classical models of…

Sources of patient uncertainty when reviewing medical disclosure and consent documentation.

Science.gov (United States)

Donovan-Kicken, Erin; Mackert, Michael; Guinn, Trey D; Tollison, Andrew C; Breckinridge, Barbara

2013-02-01

Despite evidence that medical disclosure and consent forms are ineffective at communicating the risks and hazards of treatment and diagnostic procedures, little is known about exactly why they are difficult for patients to understand. The objective of this research was to examine what features of the forms increase people's uncertainty. Interviews were conducted with 254 individuals. After reading a sample consent form, participants described what they found confusing in the document. With uncertainty management as a theoretical framework, interview responses were analyzed for prominent themes. Four distinct sources of uncertainty emerged from participants' responses: (a) language, (b) risks and hazards, (c) the nature of the procedure, and (d) document composition and format. Findings indicate the value of simplifying medico-legal jargon, signposting definitions of terms, removing language that addresses multiple readers simultaneously, reorganizing bulleted lists of risks, and adding section breaks or negative space. These findings offer suggestions for providing more straightforward details about risks and hazards to patients, not necessarily through greater amounts of information but rather through more clear and sufficient material and better formatting. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

The Application Of Open-Source And Free Photogrammetric Software For The Purposes Of Cultural Heritage Documentation

Directory of Open Access Journals (Sweden)

Bartoš Karol

2014-07-01

Full Text Available The documentation of cultural heritage is an essential part of appropriate care of historical monuments, representing a part of our history. At present, it represents the current issue, for which considerable funds are being spent, as well as for the documentation of immovable historical monuments in a form of castle ruins, among the others. Non-contact surveying technologies - terrestrial laser scanning and digital photogrammetry belong to the most commonly used technologies, by which suitable documentation can be obtained, however their use may be very costly. In recent years, various types of software products and web services based on the SfM (or MVS method and developed as open-source software, or as a freely available and free service, relying on the basic principles of photogrammetry and computer vision, have started to get into the spotlight. By using the services and software, acquired digital images of a given object can be processed into a point cloud, serving directly as a final output or as a basis for further processing. The aim of this paper, based on images of various objects of the Slanec castle ruins obtained by the DSLR Pentax K5, is to assess the suitability of different types of open-source and free software and free web services and their reliability in terms of surface reconstruction and photo-texture quality for the purposes of castle ruins documentation.

Advanced Photon Source experimental beamline Safety Assessment Document: Addendum to the Advanced Photon Source Accelerator Systems Safety Assessment Document (APS-3.2.2.1.0)

International Nuclear Information System (INIS)

1995-01-01

This Safety Assessment Document (SAD) addresses commissioning and operation of the experimental beamlines at the Advanced Photon Source (APS). Purpose of this document is to identify and describe the hazards associated with commissioning and operation of these beamlines and to document the measures taken to minimize these hazards and mitigate the hazard consequences. The potential hazards associated with the commissioning and operation of the APS facility have been identified and analyzed. Physical and administrative controls mitigate identified hazards. No hazard exists in this facility that has not been previously encountered and successfully mitigated in other accelerator and synchrotron radiation research facilities. This document is an updated version of the APS Preliminary Safety Analysis Report (PSAR). During the review of the PSAR in February 1990, the APS was determined to be a Low Hazard Facility. On June 14, 1993, the Acting Director of the Office of Energy Research endorsed the designation of the APS as a Low Hazard Facility, and this Safety Assessment Document supports that designation

[Efficiency of computer-based documentation in long-term care--preliminary project].

Science.gov (United States)

Lüngen, Markus; Gerber, Andreas; Rupprecht, Christoph; Lauterbach, Karl W

2008-06-01

In Germany the documentation of processes in long-term care is mainly paper-based. Planning, realization and evaluation are not supported in an optimal way. In a preliminary study we evaluated the consequences of the introduction of a computer-based documentation system using handheld devices. We interviewed 16 persons before and after introducing the computer-based documentation and assessed costs for the documentation process and administration. The results show that reducing costs is likely. The job satisfaction of the personnel increased, more time could be spent for caring for the residents. We suggest further research to reach conclusive results.

SOURCE TERMS FOR HLW GLASS CANISTERS

International Nuclear Information System (INIS)

J.S. Tang

2000-01-01

This calculation is prepared by the Monitored Geologic Repository (MGR) Waste Package Design Section. The objective of this calculation is to determine the source terms that include radionuclide inventory, decay heat, and radiation sources due to gamma rays and neutrons for the high-level radioactive waste (HLW) from the, West Valley Demonstration Project (WVDP), Savannah River Site (SRS), Hanford Site (HS), and Idaho National Engineering and Environmental Laboratory (INEEL). This calculation also determines the source terms of the canister containing the SRS HLW glass and immobilized plutonium. The scope of this calculation is limited to source terms for a time period out to one million years. The results of this calculation may be used to carry out performance assessment of the potential repository and to evaluate radiation environments surrounding the waste packages (WPs). This calculation was performed in accordance with the Development Plan ''Source Terms for HLW Glass Canisters'' (Ref. 7.24)

Analysis of safety information for nuclear power plants and development of source term estimation program

International Nuclear Information System (INIS)

Kim, Tae Woon; Choi, Seong Soo; Park, Jin Hee

1999-12-01

Current CARE(Computerized Advisory System for Radiological Emergency) in KINS(Korea Institute of Nuclear Safety) has no STES(Source Term Estimation System) which links between SIDS(Safety Information Display System) and FADAS(Following Accident Dose Assessment System). So in this study, STES is under development. STES system is the system that estimates the source term based on the safety information provided by SIDS. Estimated source term is given to FADAS as an input for estimation of environmental effect of radiation. Through this first year project STES for the Kori 3,4 and Younggwang 1,2 has been developed. Since there is no CARE for Wolsong(PHWR) plants yet, CARE for Wolsong is under construction. The safety parameters are selected and the safety information display screens and the alarm logic for plant status change are developed for Wolsong Unit 2 based on the design documents for CANDU plants

10 CFR 50.67 - Accident source term.

Science.gov (United States)

2010-01-01

... Conditions of Licenses and Construction Permits § 50.67 Accident source term. (a) Applicability. The... 10 Energy 1 2010-01-01 2010-01-01 false Accident source term. 50.67 Section 50.67 Energy NUCLEAR... to January 10, 1997, who seek to revise the current accident source term used in their design basis...

ORIGAMI Automator Primer. Automated ORIGEN Source Terms and Spent Fuel Storage Pool Analysis

Energy Technology Data Exchange (ETDEWEB)

Wieselquist, William A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Thompson, Adam B. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bowman, Stephen M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Peterson, Joshua L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2016-04-01

Source terms and spent nuclear fuel (SNF) storage pool decay heat load analyses for operating nuclear power plants require a large number of Oak Ridge Isotope Generation and Depletion (ORIGEN) calculations. SNF source term calculations also require a significant amount of bookkeeping to track quantities such as core and assembly operating histories, spent fuel pool (SFP) residence times, heavy metal masses, and enrichments. The ORIGEN Assembly Isotopics (ORIGAMI) module in the SCALE code system provides a simple scheme for entering these data. However, given the large scope of the analysis, extensive scripting is necessary to convert formats and process data to create thousands of ORIGAMI input files (one per assembly) and to process the results into formats readily usable by follow-on analysis tools. This primer describes a project within the SCALE Fulcrum graphical user interface (GUI) called ORIGAMI Automator that was developed to automate the scripting and bookkeeping in large-scale source term analyses. The ORIGAMI Automator enables the analyst to (1) easily create, view, and edit the reactor site and assembly information, (2) automatically create and run ORIGAMI inputs, and (3) analyze the results from ORIGAMI. ORIGAMI Automator uses the standard ORIGEN binary concentrations files produced by ORIGAMI, with concentrations available at all time points in each assembly’s life. The GUI plots results such as mass, concentration, activity, and decay heat using a powerful new ORIGEN Post-Processing Utility for SCALE (OPUS) GUI component. This document includes a description and user guide for the GUI, a step-by-step tutorial for a simplified scenario, and appendices that document the file structures used.

Calculation of source terms for NUREG-1150

International Nuclear Information System (INIS)

Breeding, R.J.; Williams, D.C.; Murfin, W.B.; Amos, C.N.; Helton, J.C.

1987-10-01

The source terms estimated for NUREG-1150 are generally based on the Source Term Code Package (STCP), but the actual source term calculations used in computing risk are performed by much smaller codes which are specific to each plant. This was done because the method of estimating the uncertainty in risk for NUREG-1150 requires hundreds of source term calculations for each accident sequence. This is clearly impossible with a large, detailed code like the STCP. The small plant-specific codes are based on simple algorithms and utilize adjustable parameters. The values of the parameters appearing in these codes are derived from the available STCP results. To determine the uncertainty in the estimation of the source terms, these parameters were varied as specified by an expert review group. This method was used to account for the uncertainties in the STCP results and the uncertainties in phenomena not considered by the STCP

Subsurface Shielding Source Term Specification Calculation

International Nuclear Information System (INIS)

S.Su

2001-01-01

The purpose of this calculation is to establish appropriate and defensible waste-package radiation source terms for use in repository subsurface shielding design. This calculation supports the shielding design for the waste emplacement and retrieval system, and subsurface facility system. The objective is to identify the limiting waste package and specify its associated source terms including source strengths and energy spectra. Consistent with the Technical Work Plan for Subsurface Design Section FY 01 Work Activities (CRWMS M and O 2001, p. 15), the scope of work includes the following: (1) Review source terms generated by the Waste Package Department (WPD) for various waste forms and waste package types, and compile them for shielding-specific applications. (2) Determine acceptable waste package specific source terms for use in subsurface shielding design, using a reasonable and defensible methodology that is not unduly conservative. This calculation is associated with the engineering and design activity for the waste emplacement and retrieval system, and subsurface facility system. The technical work plan for this calculation is provided in CRWMS M and O 2001. Development and performance of this calculation conforms to the procedure, AP-3.12Q, Calculations

ITER Safety Task NID-5A, Subtask 1-1: Source terms and energies - initial tritium source terms. Final report

International Nuclear Information System (INIS)

Fong, C.; Kalyanam, K.M.; Tanaka, M.R.; Sood, S.; Natalizio, A.; Delisle, M.

1995-02-01

The overall objective of the Early Safety and Environmental Characterization Study (ESECS) is to assess the environmental impact of tritium using appropriate assumptions on a hypothetical site for ITER, having the r eference s ite characteristics as proposed by the JCT. The objective of this work under the above subtask 1-1, NID-5a, is to determine environmental source terms (i.e., process source term x containment release fraction) for the fuel cycle and cooling systems. The work is based on inventories and process source terms (i.e., inventory x mobilization fraction), provided by others (under Task NID 3b). The results of this work form the basis for the determination, by others, of the off-site dose (i.e., environmental source term x dose/release ratio). For the determination of the environmental source terms, the TMAP4 code has been utilized (ref 1). This code is approved by ITER for safety assessment. Volume 3 is a compilation of appendices giving detailed results of the study

ITER Safety Task NID-5A, Subtask 1-1: Source terms and energies - initial tritium source terms. Final report

International Nuclear Information System (INIS)

Fong, C.; Kalyanam, K.M.; Tanaka, M.R.; Sood, S.; Natalizio, A.; Delisle, M.

1995-02-01

The overall objective of the Early Safety and Environmental Characterization Study (ESECS) is to assess the environmental impact of tritium using appropriate assumptions on a hypothetical site for ITER, having the r eference s ite characteristics as proposed by the JCT. The objective of this work under the above subtask 1-1, NID-5a, is to determine environmental source terms (i.e., process source term x containment release fraction) for the fuel cycle and cooling systems. The work is based on inventories and process source terms (i.e., inventory x mobilization fraction), provided by others (under Task NID 3b). The results of this work form the basis for the determination, by others, of the off-site dose (i.e., environmental source term x dose/release ratio). For the determination of the environmental source terms, the TMAP4 code has been utilized (ref 1). This code is approved by ITER for safety assessment. 6 refs

INEEL Subregional Conceptual Model Report Volume 3: Summary of Existing Knowledge of Natural and Anthropogenic Influences on the Release of Contaminants to the Subsurface Environment from Waste Source Terms at the INEEL

Energy Technology Data Exchange (ETDEWEB)

Paul L. Wichlacz

2003-09-01

This source-term summary document is intended to describe the current understanding of contaminant source terms and the conceptual model for potential source-term release to the environment at the Idaho National Engineering and Environmental Laboratory (INEEL), as presented in published INEEL reports. The document presents a generalized conceptual model of the sources of contamination and describes the general categories of source terms, primary waste forms, and factors that affect the release of contaminants from the waste form into the vadose zone and Snake River Plain Aquifer. Where the information has previously been published and is readily available, summaries of the inventory of contaminants are also included. Uncertainties that affect the estimation of the source term release are also discussed where they have been identified by the Source Term Technical Advisory Group. Areas in which additional information are needed (i.e., research needs) are also identified.

Determination of Source Term for an Annual Stack Release of Gas Reactor G.A. Siwabessy

International Nuclear Information System (INIS)

Sudiyati; Syahrir; Unggul Hartoyo; Nugraha Luhur

2008-01-01

Releases of radionuclide from the reactor are noble gases, halogenides and particulates. The measurements were carried out directly on the air monitoring system of the stack. The results of these measurements are compared with the annual Source-Term data from the Safety Analyses report (SAR) of RSG-GAS. The measurement results are smaller than the data reported in SAR document. (author)

ITER Safety Task NID-5A, Subtask 1-1: Source terms and energies - initial tritium source terms. Final report

International Nuclear Information System (INIS)

Fong, C.; Kalyanam, K.M.; Tanaka, M.R.; Sood, S.; Natalizio, A.; Delisle, M.

1995-02-01

The overall objective of the Early Safety and Environmental Characterization Study (ESECS) is to assess the environmental impact of tritium using appropriate assumptions on a hypothetical site for ITER, having the r eference s ite characteristics as proposed by the JCT. The objective of this work under the above subtask 1-1, NID-5a, is to determine environmental source terms (i.e., process source term x containment release fraction) for the fuel cycle and cooling systems. The work is based on inventories and process source terms (i.e., inventory x mobilization fraction), provided by others (under Task NID 3b). The results of this work form the basis for the determination, by others, of the off-site dose (i.e., environmental source term x dose/release ratio). For the determination of the environmental source terms, the TMAP4 code has been utilized (ref 1). This code is approved by ITER for safety assessment. Volume 2 is a compilation of appendices giving detailed results of the study. 5 figs

Aerosol behavior and light water reactor source terms

International Nuclear Information System (INIS)

Abbey, F.; Schikarski, W.O.

1988-01-01

The major developments in nuclear aerosol modeling following the accident to pressurized water reactor Unit 2 at Three Mile Island are briefly reviewed and the state of the art summarized. The importance and implications of these developments for severe accident source terms for light water reactors are then discussed in general terms. The treatment is not aimed at identifying specific source term values but is intended rather to illustrate trends, to assess the adequacy of the understanding of major aspects of aerosol behavior for source term prediction, and demonstrate in qualitative terms the effect of various aspects of reactor design. Areas where improved understanding of aerosol behavior might lead to further reductions in current source terms predictions are also considered

Probabilistic source term predictions for use with decision support systems

International Nuclear Information System (INIS)

Grindon, E.; Kinniburgh, C.G.

2003-01-01

Probabilistic Inference of Nuclear Power plant Transients (SPRINT), the SPRINT tool takes, as input, observations and trends in key instrument readings from the Nuclear Power Plant (NPP). lt uses these observations to interrogate a database of precalculated source terms, typically compiled from existing NPP analyses performed as Part of a Level 2 PSA study. The basis for this interrogation is a probabilistic logic model, or belief network, of plant behaviour developed by plant experts (using, as a platform, the Netica Bayesian network Software). This is included in the application as a data file. The end points of this logic model are then mapped onto the database of pre-calculated source terms. This process is very rapid (taking only as long as is required to input the responses to a series of questions about the NPP status) and can overcome 'don't know' responses in the question set by resorting to prior probabilities determined by the plant experts who set up the model. The SPRINT application is the combination of the main SPRINT interface containing the user input/output screens and the logic model (dne file) loaded in the Netica application. The conditional probability tables. Beside the network structure itself, the key data in the model are the conditional probabilities that define the strength of influence of a parent node an a daughter node. These values are stored in the model file as network tables, one table per, node, called Conditional Probability Tables (CPTs). However, as detailed documentation of the CPT values is vital during development of reactor specific models, the Net2SS pro.gram was written to take any dne file and output the CPT data as an Excel spreadsheet which can be modified, annotated and loaded back into the dne file via the SPRINT interface. The repository file. The parameters defining the source term data stored in the Excel repository file is determined by the requirement that SPRINT be capable of generating input files for Decision Support

Tank waste source term inventory validation. Volume 1. Letter report

International Nuclear Information System (INIS)

Brevick, C.H.; Gaddis, L.A.; Johnson, E.D.

1995-01-01

The sample data for selection of 11 radionuclides and 24 chemical analytes were extracted from six separate sample data sets, were arranged in a tabular format and were plotted on scatter plots for all of the 149 single-shell tanks, the 24 double-shell tanks and the four aging waste tanks. The solid and liquid sample data was placed in separate tables and plots. The sample data and plots were compiled from the following data sets: characterization raw sample data, recent core samples, D. Braun data base, Wastren (Van Vleet) data base, TRAC and HTCE inventories. This document is Volume I of the Letter Report entitled Tank Waste Source Term Inventory Validation

Mechanistic facility safety and source term analysis

International Nuclear Information System (INIS)

PLYS, M.G.

1999-01-01

A PC-based computer program was created for facility safety and source term analysis at Hanford The program has been successfully applied to mechanistic prediction of source terms from chemical reactions in underground storage tanks, hydrogen combustion in double contained receiver tanks, and proccss evaluation including the potential for runaway reactions in spent nuclear fuel processing. Model features include user-defined facility room, flow path geometry, and heat conductors, user-defined non-ideal vapor and aerosol species, pressure- and density-driven gas flows, aerosol transport and deposition, and structure to accommodate facility-specific source terms. Example applications are presented here

Some practical implications of source term reassessment

International Nuclear Information System (INIS)

1988-03-01

This report provides a brief summary of the current knowledge of severe accident source terms and suggests how this knowledge might be applied to a number of specific aspects of reactor safety. In preparing the report, consideration has been restricted to source term issues relating to light water reactors (LWRs). Consideration has also generally been restricted to the consequences of hypothetical severe accidents rather than their probability of occurrence, although it is recognized that, in the practical application of source term research, it is necessary to take account of probability as well as consequences. The specific areas identified were as follows: Exploration of the new insights that are available into the management of severe accidents; Investigating the impact of source term research on emergency planning and response; Assessing the possibilities which exist in present reactor designs for preventing or mitigating the consequences of severe accidents and how these might be used effectively; Exploring the need for backfitting and assessing the implications of source term research for future designs; and Improving the quantification of the radiological consequences of hypothetical severe accidents for probabilistic safety assessments (PSAs) and informing the public about the realistic risks associated with nuclear power plants. 7 refs

The Chernobyl reactor accident source term: development of a consensus view

International Nuclear Information System (INIS)

Devell, L.; Guntay, S.; Powers, D.A.

1995-11-01

Ten years after the reactor accident at Chernobyl, a great deal more data is available concerning the events, phenomena, and processes that took place. The purpose of this document is to examine what is known about the radioactive materials released during the accident, a task that is substantially more difficult than it might first appear to be. The Chernobyl station, like other nuclear power plants, was not instrumented to characterize a disastrous accident. The accident was peculiar in the sense that radioactive materials were released, at least initially, in an exceptionally energetic plume and were transported far from the reactor site. Release of radioactivity from the plant continued for several days. Characterization of the contamination caused by the releases of radioactivity has had a much lower priority than remediation of the contamination. Consequently, an assessment of the Chernobyl accident source term must rely to a significant extent on inferential evidence. The assessment presented here begins with an examination of the core inventories of radioactive materials. In subsequent sections of the report, the magnitude and timing of the releases of radioactivity are described. Then, the composition, chemical forms, and physical forms of the releases are discussed. A number of more recent publications and results from scientists in Russia and elsewhere have significantly improved the understanding of the Chernobyl source term. Because of the special features of the reactor design and the peculiarities of the Chernobyl accident, the source term for the Chernobyl accident is of limited applicability to the safety analysis of other types of reactors

Revised accident source terms for light-water reactors

Energy Technology Data Exchange (ETDEWEB)

Soffer, L. [Nuclear Regulatory Commission, Washington, DC (United States)

1995-02-01

This paper presents revised accident source terms for light-water reactors incorporating the severe accident research insights gained in this area over the last 15 years. Current LWR reactor accident source terms used for licensing date from 1962 and are contained in Regulatory Guides 1.3 and 1.4. These specify that 100% of the core inventory of noble gases and 25% of the iodine fission products are assumed to be instantaneously available for release from the containment. The chemical form of the iodine fission products is also assumed to be predominantly elemental iodine. These assumptions have strongly affected present nuclear air cleaning requirements by emphasizing rapid actuation of spray systems and filtration systems optimized to retain elemental iodine. A proposed revision of reactor accident source terms and some im implications for nuclear air cleaning requirements was presented at the 22nd DOE/NRC Nuclear Air Cleaning Conference. A draft report was issued by the NRC for comment in July 1992. Extensive comments were received, with the most significant comments involving (a) release fractions for both volatile and non-volatile species in the early in-vessel release phase, (b) gap release fractions of the noble gases, iodine and cesium, and (c) the timing and duration for the release phases. The final source term report is expected to be issued in late 1994. Although the revised source terms are intended primarily for future plants, current nuclear power plants may request use of revised accident source term insights as well in licensing. This paper emphasizes additional information obtained since the 22nd Conference, including studies on fission product removal mechanisms, results obtained from improved severe accident code calculations and resolution of major comments, and their impact upon the revised accident source terms. Revised accident source terms for both BWRS and PWRS are presented.

Modification to ORIGEN2 for generating N Reactor source terms. Volume 1

International Nuclear Information System (INIS)

Schwarz, R.A.

1997-04-01

This report discusses work that has been done to upgrade the ORIGEN2 code cross sections to be compatible with the WIMS computer code data. Because of the changes in the ORIGEN2 calculations. Details on changes made to the ORIGEN2 computer code and the Radnuc code will be discussed along with additional work that should be done in the future to upgrade both ORIGEN2 and Radnuc. A detailed historical description of how source terms have been generated for N Reactor fuel stored in the K Basins has been generated. The neutron source discussed in this description was generated by the WIMS computer code (Gubbins et al. 1982) because of known shortcomings in the ORIGEN2 (Croff 1980) cross sections. Another document includes a discussion of the ORIGEN2 cross sections

Some problems in the categorization of source terms

International Nuclear Information System (INIS)

Abbey, F.; Dunbar, I.H.; Hayns, M.R.; Nixon, W.

1985-01-01

In recent years techniques for calculating source terms have been considerably improved. It would be unfortunate if the new information were to be blurred by the use of old schemes for the categorization of source terms. In the past categorization schemes have been devised without the question of the general principles of categorization and the available options being addressed explicitly. In this paper these principles are set out, providing a framework within which categorization schemes used in past probabilistic risk assessments and possible future improvements are discussed. In particular the use of input from scoping consequence calculations in deciding how to group source terms, and the question of how modelling uncertainties may be expressed as uncertainties in a final category source terms are considered

Study of short time effect on health of a local air pollution source. Epidemiological approach; Etude des effets a court terme sur la sante d'une source locale de pollution atmospherique. Approche epidemiologique

Energy Technology Data Exchange (ETDEWEB)

Guzzo, J.Ch. [Institut National de Veille Sanitaire, Reseau National de Sante Publique, 94 - Saint-Maurice (France)

2000-07-01

This document applies to health professionals who are facing with a problem of risks evaluation relative to a local source of air pollution and envisage to realize an epidemiological study. In this document, only the short term effects are considered and the situations of accidental pollution are not treated. Without being a methodological treatise it can be a tool to better understand the constraints and the limits of epidemiology to answer the difficult question of the impact evaluation on health of populations living near a local source of air pollution. (N.C.)

Tank waste source term inventory validation. Volume II. Letter report

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-04-01

This document comprises Volume II of the Letter Report entitled Tank Waste Source Term Inventory Validation. This volume contains Appendix C, Radionuclide Tables, and Appendix D, Chemical Analyte Tables. The sample data for selection of 11 radionuclides and 24 chemical analytes were extracted from six separate sample data sets, were arranged in a tabular format and were plotted on scatter plots for all of the 149 single-shell tanks, the 24 double-shell tanks and the four aging waste tanks. The solid and liquid sample data was placed in separate tables and plots. The sample data and plots were compiled from the following data sets: characterization raw sample data, recent core samples, D. Braun data base, Wastren (Van Vleet) data base, TRAC and HTCE inventories.

Tank waste source term inventory validation. Volume II. Letter report

International Nuclear Information System (INIS)

1995-04-01

This document comprises Volume II of the Letter Report entitled Tank Waste Source Term Inventory Validation. This volume contains Appendix C, Radionuclide Tables, and Appendix D, Chemical Analyte Tables. The sample data for selection of 11 radionuclides and 24 chemical analytes were extracted from six separate sample data sets, were arranged in a tabular format and were plotted on scatter plots for all of the 149 single-shell tanks, the 24 double-shell tanks and the four aging waste tanks. The solid and liquid sample data was placed in separate tables and plots. The sample data and plots were compiled from the following data sets: characterization raw sample data, recent core samples, D. Braun data base, Wastren (Van Vleet) data base, TRAC and HTCE inventories

Source term assessment, containment atmosphere control systems, and accident consequences. Report to CSNI by an OECD/NEA Group of experts

International Nuclear Information System (INIS)

1987-04-01

CSNI Report 135 summarizes the results of the work performed by CSNI's Principal Working Group No. 4 on the Source Term and Environmental Consequences (PWG4) during the period extending from 1983 to 1986. This document contains the latest information on some important topics relating to source terms, accident consequence assessment, and containment atmospheric control systems. It consists of five parts: (1) a Foreword and Executive Summary prepared by PWG4's Chairman; (2) a Report on the Technical Status of the Source Term; (3) a Report on the Technical Status of Filtration and Containment Atmosphere Control Systems for Nuclear Reactors in the Event of a Severe Accident; (4) a Report on the Technical Status of Reactor Accident Consequence Assessment; (5) a list of members of PWG4

Source document for waste area groupings at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

Osborne, P.L.; Kuhaida, A.J., Jr.

1996-09-01

This document serves as a source document for Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) and other types of documents developed for and pertaining to Environmental Restoration (ER) Program activities at Oak Ridge National Laboratory (ORNL). It contains descriptions of the (1) regulatory requirements for the ORR ER Program, (2) Oak Ridge Reservation (ORR) ER Program, (3) ORNL site history and characterization, and (4) history and characterization of Waste Area Groupings (WAGS) 1-20. This document was created to save time, effort, and money for persons and organizations drafting documents for the ER Program and to improve consistency in the documents prepared for the program. By eliminating the repetitious use of selected information about the program, this document will help reduce the time and costs associated with producing program documents. By serving as a benchmark for selected information about the ER Program, this reference will help ensure that information presented in future documents is accurate and complete

Unclassified Sources Term and Radionuclide Data for Corrective Action Unit 97: Yucca Flat/Climax Mine, Nevada Test Site, Nevada, Revision 2

Energy Technology Data Exchange (ETDEWEB)

Peter Martian

2009-08-01

This report documents the evaluation of the information and data available on the unclassified source term and radionuclide contamination for CAU 97: Yucca Flat/Climax Mine. The total residual inventory of radionuclides associated with one or more tests is known as the radiologic source term (RST). The RST is comprised of radionuclides in water, glass, or other phases or mineralogic forms. The hydrologic source term (HST) of an underground nuclear test is the portion of the total RST that is released into the groundwater over time following the test. In this report, the HST represents radionuclide release some time after the explosion and does not include the rapidly evolving mechanical, thermal, and chemical processes during the explosion. The CAU 97: Yucca Flat/Climax Mine has many more detonations and a wider variety of settings to consider compared to other CAUs. For instance, the source term analysis and evaluation performed for CAUs 101 and 102: Central and Western Pahute Mesa and CAU 98: Frenchman Flat did not consider vadose zone attenuation because many detonations were located near or below the water table. However, the large number of Yucca Flat/Climax Mine tests and the location of many tests above the water table warrant a more robust analysis of the unsaturated zone. The purpose of this report is to develop and document conceptual models of the Yucca Flat/Climax Mine HST for use in implementing source terms for the Yucca Flat/Climax Mine models. This document presents future plans to incorporate the radionuclide attenuation mechanisms due to unsaturated/multiphase flow and transport within the Yucca Flat CAU scale modeling. The important processes that influence radionuclide migration for the unsaturated and saturated tests in alluvial, volcanic, and carbonate settings are identified. Many different flow and transport models developed by Lawrence Livermore National Laboratory (LLNL) and Los Alamos National Laboratory (LANL), including original

Chernobyl source term estimation

International Nuclear Information System (INIS)

Gudiksen, P.H.; Harvey, T.F.; Lange, R.

1990-09-01

The Chernobyl source term available for long-range transport was estimated by integration of radiological measurements with atmospheric dispersion modeling and by reactor core radionuclide inventory estimation in conjunction with WASH-1400 release fractions associated with specific chemical groups. The model simulations revealed that the radioactive cloud became segmented during the first day, with the lower section heading toward Scandinavia and the upper part heading in a southeasterly direction with subsequent transport across Asia to Japan, the North Pacific, and the west coast of North America. By optimizing the agreement between the observed cloud arrival times and duration of peak concentrations measured over Europe, Japan, Kuwait, and the US with the model predicted concentrations, it was possible to derive source term estimates for those radionuclides measured in airborne radioactivity. This was extended to radionuclides that were largely unmeasured in the environment by performing a reactor core radionuclide inventory analysis to obtain release fractions for the various chemical transport groups. These analyses indicated that essentially all of the noble gases, 60% of the radioiodines, 40% of the radiocesium, 10% of the tellurium and about 1% or less of the more refractory elements were released. These estimates are in excellent agreement with those obtained on the basis of worldwide deposition measurements. The Chernobyl source term was several orders of magnitude greater than those associated with the Windscale and TMI reactor accidents. However, the 137 Cs from the Chernobyl event is about 6% of that released by the US and USSR atmospheric nuclear weapon tests, while the 131 I and 90 Sr released by the Chernobyl accident was only about 0.1% of that released by the weapon tests. 13 refs., 2 figs., 7 tabs

Source term and radiological consequences of the Chernobyl accident

International Nuclear Information System (INIS)

Mourad, R.

1987-09-01

This report presents the results of a study of the source term and radiological consequences of the Chernobyl accident. The results two parts. The first part was performed during the first 2 months following the accident and dealt with the evaluation of the source term and an estimate of individual doses in the European countries outside the Soviet Union. The second part was performed after August 25-29, 1986 when the Soviets presented in a IAEA Conference in Vienna detailed information about the accident, including source term and radiological consequences in the Soviet Union. The second part of the study reconfirms the source term evaluated in the first part and in addition deals with the radiological consequences in the Soviet Union. Source term and individual doses are calculated from measured post-accident data, reported by the Soviet Union and European countries, microcomputer program PEAR (Public Exposure from Accident Releases). 22 refs

Phase 1 immobilized low-activity waste operational source term

International Nuclear Information System (INIS)

Burbank, D.A.

1998-01-01

This report presents an engineering analysis of the Phase 1 privatization feeds to establish an operational source term for storage and disposal of immobilized low-activity waste packages at the Hanford Site. The source term information is needed to establish a preliminary estimate of the numbers of remote-handled and contact-handled waste packages. A discussion of the uncertainties and their impact on the source term and waste package distribution is also presented. It should be noted that this study is concerned with operational impacts only. Source terms used for accident scenarios would differ due to alpha and beta radiation which were not significant in this study

Source term analyses under severe accidents for KNGR

Energy Technology Data Exchange (ETDEWEB)

Song, Yong Mann; Park, Soo Yong

2001-03-01

In this study, in-containment source term for LOFW (Loss of Feed Water), which has appeared the most frequent core melt accident, is calculated and compared with NUREG-1465 source term. This study provides not only new source term data using MELCOR1.8.4 and its state-of-the-art models but also evaluating basis of KNGR design and its mitigation capability under severe accidents. As the selected accident is identical with LOFW-S17, which has been analyzed using MAAP by KEPCO with only difference of 2 SITs, mutual comparison of the results is especially expected.

A simplified approach to evaluating severe accident source term for PWR

International Nuclear Information System (INIS)

Huang, Gaofeng; Tong, Lili; Cao, Xuewu

2014-01-01

Highlights: • Traditional source term evaluation approaches have been studied. • A simplified approach of source term evaluation for 600 MW PWR is studied. • Five release categories are established. - Abstract: For early design of NPPs, no specific severe accident source term evaluation was considered. Some general source terms have been used for some NPPs. In order to implement a best estimate, a special source term evaluation should be implemented for an NPP. Traditional source term evaluation approaches (mechanism approach and parametric approach) have some difficulties associated with their implementation. The traditional approaches are not consistent with cost-benefit assessment. A simplified approach for evaluating severe accident source term for PWR is studied. For the simplified approach, a simplified containment event tree is established. According to representative cases selection, weighted coefficient evaluation, computation of representative source term cases and weighted computation, five containment release categories are established, including containment bypass, containment isolation failure, containment early failure, containment late failure and intact containment

Effect of source term composition on offsite doses

International Nuclear Information System (INIS)

Karahalios, P.; Gardner, R.

1985-01-01

The development of new realistic accident source terms has identified the need to establish a basis for comparing the impact of such source terms. This paper attempts to develop a generalized basis of comparison by investigating contributions to offsite acute whole body doses from each group of radionuclides being released to the atmosphere, using CRAC2. The paper also investigates the effect of important parameters such as regional meteorology, sheltering, and duration of release. Finally, the paper focuses on significant changes in the relative importance of individual radionuclide groups in PWR2, SST1, and a revision of the Stone and Webster proposed interim source term

Bayesian source term determination with unknown covariance of measurements

Science.gov (United States)

Belal, Alkomiet; Tichý, Ondřej; Šmídl, Václav

2017-04-01

Determination of a source term of release of a hazardous material into the atmosphere is a very important task for emergency response. We are concerned with the problem of estimation of the source term in the conventional linear inverse problem, y = Mx, where the relationship between the vector of observations y is described using the source-receptor-sensitivity (SRS) matrix M and the unknown source term x. Since the system is typically ill-conditioned, the problem is recast as an optimization problem minR,B(y - Mx)TR-1(y - Mx) + xTB-1x. The first term minimizes the error of the measurements with covariance matrix R, and the second term is a regularization of the source term. There are different types of regularization arising for different choices of matrices R and B, for example, Tikhonov regularization assumes covariance matrix B as the identity matrix multiplied by scalar parameter. In this contribution, we adopt a Bayesian approach to make inference on the unknown source term x as well as unknown R and B. We assume prior on x to be a Gaussian with zero mean and unknown diagonal covariance matrix B. The covariance matrix of the likelihood R is also unknown. We consider two potential choices of the structure of the matrix R. First is the diagonal matrix and the second is a locally correlated structure using information on topology of the measuring network. Since the inference of the model is intractable, iterative variational Bayes algorithm is used for simultaneous estimation of all model parameters. The practical usefulness of our contribution is demonstrated on an application of the resulting algorithm to real data from the European Tracer Experiment (ETEX). This research is supported by EEA/Norwegian Financial Mechanism under project MSMT-28477/2014 Source-Term Determination of Radionuclide Releases by Inverse Atmospheric Dispersion Modelling (STRADI).

A comparison of world-wide uses of severe reactor accident source terms

International Nuclear Information System (INIS)

Ang, M.L.; Frid, W.; Kersting, E.J.; Friederichs, H.G.; Lee, R.Y.; Meyer-Heine, A.; Powers, D.A.; Soda, K.; Sweet, D.

1994-09-01

The definitions of source terms to reactor containments and source terms to the environment are discussed. A comparison is made between the TID-14844 example source term and the alternative source term described in NUREG-1465. Comparisons of these source terms to the containments and those used in France, Germany, Japan, Sweden, and the United Kingdom are made. Source terms to the environment calculated in NUREG-1500 and WASH-1400 are discussed. Again, these source terms are compared to those now being used in France, Germany, Japan, Sweden, and the United Kingdom. It is concluded that source terms to the containment suggested in NUREG-1465 are not greatly more conservative than those used in other countries. Technical bases for the source terms are similar. The regulatory use of the current understanding of radionuclide behavior varies among countries

The Chernobyl reactor accident source term: Development of a consensus view

International Nuclear Information System (INIS)

Guntay, S.; Powers, D.A.; Devell, L.

1997-01-01

In August 1986, scientists from the former Soviet Union provided the nuclear safety community with an impressively detailed account of what was then known about the Chernobyl accident. This included assessments of the magnitudes, rates, and compositions of radionuclide releases during the ten days following initiation of the accident. A summary report based on the Soviet report, the oral presentations, and the discussions with scientists from various countries was issued by the International Atomic Energy Agency shortly thereafter. Ten years have elapsed since the reactor accident at Chernobyl. A great deal more data is now available concerning the events, phenomena, and processes that took place. The purpose of this document is to examine what is known about the radioactive materials released during the accident. The accident was peculiar in the sense that radioactive materials were released, at least initially, in an exceptionally energetic plume and were transported far from the reactor site. Release of radioactivity from the plant continued for about ten days. A number of more recent publications and results from scientists in Russia and elsewhere have significantly improved our understanding of the Chernobyl source term. Because of the special features of the reactor design and the pecularities of the Chernobyl accident, the source term for the Chernobyl accident is of limited applicability of the safety analysis of other types of reactors

Quantification of severe accident source terms of a Westinghouse 3-loop plant

International Nuclear Information System (INIS)

Lee Min; Ko, Y.-C.

2008-01-01

Integrated severe accident analysis codes are used to quantify the source terms of the representative sequences identified in PSA study. The characteristics of these source terms depend on the detail design of the plant and the accident scenario. A historical perspective of radioactive source term is provided. The grouping of radionuclides in different source terms or source term quantification tools based on TID-14844, NUREG-1465, and WASH-1400 is compared. The radionuclides release phenomena and models adopted in the integrated severe accident analysis codes of STCP and MAAP4 are described. In the present study, the severe accident source terms for risk quantification of Maanshan Nuclear Power Plant of Taiwan Power Company are quantified using MAAP 4.0.4 code. A methodology is developed to quantify the source terms of each source term category (STC) identified in the Level II PSA analysis of the plant. The characteristics of source terms obtained are compared with other source terms. The plant analyzed employs a Westinghouse designed 3-loop pressurized water reactor (PWR) with large dry containment

An Organizational-Technical Concept to Deal with Open Source Software License Terms

Directory of Open Access Journals (Sweden)

Sergius Dyck

2016-06-01

Full Text Available Open source software (OSS released under various license terms is widely used as third party libraries in today's software projects. To ensure open source compliance within an organization, a strategic approach to OSS management is needed. As basis for such an approach, we introduce an organizational-technical concept for dealing with the various OSS licenses by using procedural instructions and build automation software. The concept includes the careful consideration of OSS license conditions. The results obtained from this consideration and additional necessary commitments are documented in a so-called license playbook. We introduce procedure instructions enabling a consistent approach for software development using OSS libraries. The procedure instructions are described in a way such that they can be implemented for example for Java projects using the popular build automation tool Apache Maven and the software repository tool Nexus. We give guidance on how to realize such an implementation on basis of automation tools in practice.

From a Content Delivery Portal to a Knowledge Management System for Standardized Cancer Documentation.

Science.gov (United States)

Schlue, Danijela; Mate, Sebastian; Haier, Jörg; Kadioglu, Dennis; Prokosch, Hans-Ulrich; Breil, Bernhard

2017-01-01

Heterogeneous tumor documentation and its challenges of interpretation of medical terms lead to problems in analyses of data from clinical and epidemiological cancer registries. The objective of this project was to design, implement and improve a national content delivery portal for oncological terms. Data elements of existing handbooks and documentation sources were analyzed, combined and summarized by medical experts of different comprehensive cancer centers. Informatics experts created a generic data model based on an existing metadata repository. In order to establish a national knowledge management system for standardized cancer documentation, a prototypical tumor wiki was designed and implemented. Requirements engineering techniques were applied to optimize this platform. It is targeted to user groups such as documentation officers, physicians and patients. The linkage to other information sources like PubMed and MeSH was realized.

Establishing Trustworthiness When Students Read Multiple Documents Containing Conflicting Scientific Evidence

Science.gov (United States)

Bråten, Ivar; Braasch, Jason L. G.; Strømsø, Helge I.; Ferguson, Leila E.

2015-01-01

Students read six documents that varied in terms of their perspectives on a scientific issue and the trustworthiness of the source features. After reading, students wrote essays, rank-ordered the documents according to perceived trustworthiness, and provided reasons for their rank-order decisions. Students put the most trust in a textbook and a…

Estimation of Source Term Behaviors in SBO Sequence in a Typical 1000MWth PWR and Comparison with Other Source Term Results

Energy Technology Data Exchange (ETDEWEB)

Kim, Tae Woon; Han, Seok Jung; Ahn, Kwang Il; Fynan, Douglas; Jung, Yong Hoon [KAERI, Daejeon (Korea, Republic of)

2016-05-15

Since the Three Mile Island (TMI) (1979), Chernobyl (1986), Fukushima Daiichi (2011) accidents, the assessment of radiological source term effects on the environment has been a key concern of nuclear safety. In the Fukushima Daiichi accident, the long-term SBO (station blackout) accident occurs. Using the worst case assumptions like in Fukushima accident on the accident sequences and on the availability of safety systems, the thermal hydraulic behaviors, core relocation and environmental source terms behaviors are estimated for long-term SBO accident for OPR-1000 reactor. MELCOR code version 1.8.6 is used in this analysis. Source term results estimated in this study is compared with other previous studies and estimated results in Fukushima accidents in UNSCEAR-2013 report. This study estimated that 11 % of iodine can be released to environment and 2% of cesium can be released to environment. UNSCEAR-2013 report estimated that 2 - 8 % of iodine have been released to environment and 1 - 3 % of cesium have been released to the environment. They have similar results in the aspect of release fractions of iodine and cesium to environment.

Review of SFR In-Vessel Radiological Source Term Studies

International Nuclear Information System (INIS)

Suk, Soo Dong; Lee, Yong Bum

2008-10-01

An effort has been made in this study to search for and review the literatures in public domain on the studies of the phenomena related to the release of radionuclides and aerosols to the reactor containment of the sodium fast reactor (SFR) plants (i.e., in-vessel source term), made in Japan and Europe including France, Germany and UK over the last few decades. Review work is focused on the experimental programs to investigate the phenomena related to determining the source terms, with a brief review on supporting analytical models and computer programs. In this report, the research programs conducted to investigate the CDA (core disruptive accident) bubble behavior in the sodium pool for determining 'primary' or 'instantaneous' source term are first introduced. The studies performed to determine 'delayed source term' are then described, including the various stages of phenomena and processes: fission product (FP) release from fuel , evaporation release from the surface of the pool, iodine mass transfer from fission gas bubble, FP deposition , and aerosol release from core-concrete interaction. The research programs to investigate the release and transport of FPs and aerosols in the reactor containment (i.e., in-containment source term) are not described in this report

Source term modelling parameters for Project-90

International Nuclear Information System (INIS)

Shaw, W.; Smith, G.; Worgan, K.; Hodgkinson, D.; Andersson, K.

1992-04-01

This document summarises the input parameters for the source term modelling within Project-90. In the first place, the parameters relate to the CALIBRE near-field code which was developed for the Swedish Nuclear Power Inspectorate's (SKI) Project-90 reference repository safety assessment exercise. An attempt has been made to give best estimate values and, where appropriate, a range which is related to variations around base cases. It should be noted that the data sets contain amendments to those considered by KBS-3. In particular, a completely new set of inventory data has been incorporated. The information given here does not constitute a complete set of parameter values for all parts of the CALIBRE code. Rather, it gives the key parameter values which are used in the constituent models within CALIBRE and the associated studies. For example, the inventory data acts as an input to the calculation of the oxidant production rates, which influence the generation of a redox front. The same data is also an initial value data set for the radionuclide migration component of CALIBRE. Similarly, the geometrical parameters of the near-field are common to both sub-models. The principal common parameters are gathered here for ease of reference and avoidance of unnecessary duplication and transcription errors. (au)

Utility view of the source term and air cleaning

International Nuclear Information System (INIS)

Littlefield, P.S.

1985-01-01

The utility view of the source term and air cleaning is discussed. The source term is made up of: (1) noble gases, which there has been a tendency to ignore in the past because it was thought there was nothing that could be done with them anyway, (2) the halogens, which have been dealt with in Air Cleaning Conferences in the past in terms of charcoal and other systems for removing them, and (3) the solid components of the source term which particulate filters are designed to handle. Air cleaning systems consist of filters, adsorbers, containment sprays, suppression pools in boiling water reactors and ice beds in ice condenser-equipped plants. The feasibility and cost of air cleaning systems are discussed

Low-level radioactive waste performance assessments: Source term modeling

International Nuclear Information System (INIS)

Icenhour, A.S.; Godbee, H.W.; Miller, L.F.

1995-01-01

Low-level radioactive wastes (LLW) generated by government and commercial operations need to be isolated from the environment for at least 300 to 500 yr. Most existing sites for the storage or disposal of LLW employ the shallow-land burial approach. However, the U.S. Department of Energy currently emphasizes the use of engineered systems (e.g., packaging, concrete and metal barriers, and water collection systems). Future commercial LLW disposal sites may include such systems to mitigate radionuclide transport through the biosphere. Performance assessments must be conducted for LUW disposal facilities. These studies include comprehensive evaluations of radionuclide migration from the waste package, through the vadose zone, and within the water table. Atmospheric transport mechanisms are also studied. Figure I illustrates the performance assessment process. Estimates of the release of radionuclides from the waste packages (i.e., source terms) are used for subsequent hydrogeologic calculations required by a performance assessment. Computer models are typically used to describe the complex interactions of water with LLW and to determine the transport of radionuclides. Several commonly used computer programs for evaluating source terms include GWSCREEN, BLT (Breach-Leach-Transport), DUST (Disposal Unit Source Term), BARRIER (Ref. 5), as well as SOURCE1 and SOURCE2 (which are used in this study). The SOURCE1 and SOURCE2 codes were prepared by Rogers and Associates Engineering Corporation for the Oak Ridge National Laboratory (ORNL). SOURCE1 is designed for tumulus-type facilities, and SOURCE2 is tailored for silo, well-in-silo, and trench-type disposal facilities. This paper focuses on the source term for ORNL disposal facilities, and it describes improved computational methods for determining radionuclide transport from waste packages

Regulatory impact of nuclear reactor accident source term assumptions. Technical report

International Nuclear Information System (INIS)

Pasedag, W.F.; Blond, R.M.; Jankowski, M.W.

1981-06-01

This report addresses the reactor accident source term implications on accident evaluations, regulations and regulatory requirements, engineered safety features, emergency planning, probabilistic risk assessment, and licensing practice. Assessment of the impact of source term modifications and evaluation of the effects in Design Basis Accident analyses, assuming a change of the chemical form of iodine from elemental to cesium iodide, has been provided. Engineered safety features used in current LWR designs are found to be effective for all postulated combinations of iodine source terms under DBA conditions. In terms of potential accident consequences, it is not expected that the difference in chemical form between elemental iodine and cesium iodide would be significant. In order to account for the current information on source terms, a spectrum of accident scenerios is discussed to realistically estimate the source terms resulting from a range of potential accident conditions

Renewable energy sources. European Commission papers; Energies renouvelables. Documents de la Commission Europeenne

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-05-01

The ''Directive on the Promotion of Electricity from Renewable Sources of Energy in the Internal Electricity Market'' was adopted in September 2001. Its purpose is to promote an increase in the contribution of renewable energy sources to electricity production in the internal market for electricity and to create a basis for a future Community framework. Energie-Cites provides in this document a summary of its opinion on the Green Paper and on Alterner II and gives a proposal for an Action Plan concerning the White Paper. (A.L.B.)

PARTITION: A program for defining the source term/consequence analysis interface in the NUREG--1150 probabilistic risk assessments

International Nuclear Information System (INIS)

Iman, R.L.; Helton, J.C.; Johnson, J.D.

1990-05-01

The individual plant analyses in the US Nuclear Regulatory Commission's reassessment of the risk from commercial nuclear power plants (NUREG-1150) consist of four parts: systems analysis, accident progression analysis, source term analysis, and consequence analysis. Careful definition of the interfaces between these parts is necessary for both information flow and computational efficiency. This document has been designed for users of the PARTITION computer program developed by the authors at Sandia National Laboratories for defining the interface between the source term analysis (performed with the XXSOR programs) and the consequence analysis (performed with the MACCS program). This report provides a tutorial that details how the interactive partitioning is performed, along with detailed information on the partitioning process. The PARTITION program was written in ANSI standard FORTRAN 77 to make the code as machine-independent (i.e., portable) as possible. 9 refs., 4 figs

Document clustering methods, document cluster label disambiguation methods, document clustering apparatuses, and articles of manufacture

Science.gov (United States)

Sanfilippo, Antonio [Richland, WA; Calapristi, Augustin J [West Richland, WA; Crow, Vernon L [Richland, WA; Hetzler, Elizabeth G [Kennewick, WA; Turner, Alan E [Kennewick, WA

2009-12-22

Document clustering methods, document cluster label disambiguation methods, document clustering apparatuses, and articles of manufacture are described. In one aspect, a document clustering method includes providing a document set comprising a plurality of documents, providing a cluster comprising a subset of the documents of the document set, using a plurality of terms of the documents, providing a cluster label indicative of subject matter content of the documents of the cluster, wherein the cluster label comprises a plurality of word senses, and selecting one of the word senses of the cluster label.

Real time source term and dose assessment

International Nuclear Information System (INIS)

Breznik, B.; Kovac, A.; Mlakar, P.

2001-01-01

The Dose Projection Programme is a tool for decision making in case of nuclear emergency. The essential input data for quick emergency evaluation in the case of hypothetical pressurised water reactor accident are following: source term, core damage assessment, fission product radioactivity, release source term and critical exposure pathways for an early phase of the release. A reduced number of radio-nuclides and simplified calculations can be used in dose calculation algorithm. Simple expert system personal computer programme has been developed for the Krsko Nuclear Power Plant for dose projection within the radius of few kilometers from the pressurised water reactor in early phase of an accident. The input data are instantaneous data of core activity, core damage indicators, release fractions, reduction factor of the release pathways, spray operation, release timing, and dispersion coefficient. Main dose projection steps are: accurate in-core radioactivity determination using reactor power input; core damage and in-containment source term assessment based on quick indications of instrumentation or on activity analysis data; user defines release pathway for typical PWR accident scenarius; dose calculation is performed only for exposure pathway critical for decision about evacuation or sheltering in early phase of an accident.(author)

Application of the source term code package to obtain a specific source term for the Laguna Verde Nuclear Power Plant

International Nuclear Information System (INIS)

Souto, F.J.

1991-06-01

The main objective of the project was to use the Source Term Code Package (STCP) to obtain a specific source term for those accident sequences deemed dominant as a result of probabilistic safety analyses (PSA) for the Laguna Verde Nuclear Power Plant (CNLV). The following programme has been carried out to meet this objective: (a) implementation of the STCP, (b) acquisition of specific data for CNLV to execute the STCP, and (c) calculations of specific source terms for accident sequences at CNLV. The STCP has been implemented and validated on CDC 170/815 and CDC 180/860 main frames as well as on a Micro VAX 3800 system. In order to get a plant-specific source term, data on the CNLV including initial core inventory, burn-up, primary containment structures, and materials used for the calculations have been obtained. Because STCP does not explicitly model containment failure, dry well failure in the form of a catastrophic rupture has been assumed. One of the most significant sequences from the point of view of possible off-site risk is the loss of off-site power with failure of the diesel generators and simultaneous loss of high pressure core spray and reactor core isolation cooling systems. The probability for that event is approximately 4.5 x 10 -6 . This sequence has been analysed in detail and the release fractions of radioisotope groups are given in the full report. 18 refs, 4 figs, 3 tabs

Source Term Model for Fine Particle Resuspension from Indoor Surfaces

National Research Council Canada - National Science Library

Kim, Yoojeong; Gidwani, Ashok; Sippola, Mark; Sohn, Chang W

2008-01-01

This Phase I effort developed a source term model for particle resuspension from indoor surfaces to be used as a source term boundary condition for CFD simulation of particle transport and dispersion in a building...

Scoping Analysis of Source Term and Functional Containment Attenuation Factors

Energy Technology Data Exchange (ETDEWEB)

Pete Lowry

2012-10-01

In order to meet future regulatory requirements, the Next Generation Nuclear Plant (NGNP) Project must fully establish and validate the mechanistic modular high temperature gas-cooled reactor (HTGR) source term. This is not possible at this stage in the project, as significant uncertainties in the final design remain unresolved. In the interim, however, there is a need to establish an approximate characterization of the source term. The NGNP team developed a simplified parametric model to establish mechanistic source term estimates for a set of proposed HTGR configurations.

Scoping Analysis of Source Term and Functional Containment Attenuation Factors

Energy Technology Data Exchange (ETDEWEB)

Pete Lowry

2012-02-01

In order to meet future regulatory requirements, the Next Generation Nuclear Plant (NGNP) Project must fully establish and validate the mechanistic modular high temperature gas-cooled reactor (HTGR) source term. This is not possible at this stage in the project, as significant uncertainties in the final design remain unresolved. In the interim, however, there is a need to establish an approximate characterization of the source term. The NGNP team developed a simplified parametric model to establish mechanistic source term estimates for a set of proposed HTGR configurations.

Scoping Analysis of Source Term and Functional Containment Attenuation Factors

Energy Technology Data Exchange (ETDEWEB)

Pete Lowry

2012-01-01

In order to meet future regulatory requirements, the Next Generation Nuclear Plant (NGNP) Project must fully establish and validate the mechanistic modular high temperature gas-cooled reactor (HTGR) source term. This is not possible at this stage in the project, as significant uncertainties in the final design remain unresolved. In the interim, however, there is a need to establish an approximate characterization of the source term. The NGNP team developed a simplified parametric model to establish mechanistic source term estimates for a set of proposed HTGR configurations.

Skyline: an open source document editor for creating and analyzing targeted proteomics experiments.

Science.gov (United States)

MacLean, Brendan; Tomazela, Daniela M; Shulman, Nicholas; Chambers, Matthew; Finney, Gregory L; Frewen, Barbara; Kern, Randall; Tabb, David L; Liebler, Daniel C; MacCoss, Michael J

2010-04-01

Skyline is a Windows client application for targeted proteomics method creation and quantitative data analysis. It is open source and freely available for academic and commercial use. The Skyline user interface simplifies the development of mass spectrometer methods and the analysis of data from targeted proteomics experiments performed using selected reaction monitoring (SRM). Skyline supports using and creating MS/MS spectral libraries from a wide variety of sources to choose SRM filters and verify results based on previously observed ion trap data. Skyline exports transition lists to and imports the native output files from Agilent, Applied Biosystems, Thermo Fisher Scientific and Waters triple quadrupole instruments, seamlessly connecting mass spectrometer output back to the experimental design document. The fast and compact Skyline file format is easily shared, even for experiments requiring many sample injections. A rich array of graphs displays results and provides powerful tools for inspecting data integrity as data are acquired, helping instrument operators to identify problems early. The Skyline dynamic report designer exports tabular data from the Skyline document model for in-depth analysis with common statistical tools. Single-click, self-updating web installation is available at http://proteome.gs.washington.edu/software/skyline. This web site also provides access to instructional videos, a support board, an issues list and a link to the source code project.

Preserving Long-Term Access to United States Government Documents in Legacy Digital Formats

Science.gov (United States)

Woods, Kam A.

2010-01-01

Over the past several decades, millions of digital objects of significant scientific, economic, cultural, and historic value have been published and distributed to libraries and archives on removable media. Providing long-term access to these documents, media files, and software executables is an increasingly complex task because of dependencies…

Review of radionuclide source terms used for performance-assessment analyses

International Nuclear Information System (INIS)

Barnard, R.W.

1993-06-01

Two aspects of the radionuclide source terms used for total-system performance assessment (TSPA) analyses have been reviewed. First, a detailed radionuclide inventory (i.e., one in which the reactor type, decay, and burnup are specified) is compared with the standard source-term inventory used in prior analyses. The latter assumes a fixed ratio of pressurized-water reactor (PWR) to boiling-water reactor (BWR) spent fuel, at specific amounts of burnup and at 10-year decay. TSPA analyses have been used to compare the simplified source term with the detailed one. The TSPA-91 analyses did not show a significant difference between the source terms. Second, the radionuclides used in source terms for TSPA aqueous-transport analyses have been reviewed to select ones that are representative of the entire inventory. It is recommended that two actinide decay chains be included (the 4n+2 ''uranium'' and 4n+3 ''actinium'' decay series), since these include several radionuclides that have potentially important release and dose characteristics. In addition, several fission products are recommended for the same reason. The choice of radionuclides should be influenced by other parameter assumptions, such as the solubility and retardation of the radionuclides

Development of source term PIRT of Fukushima Daiichi NPPs accident

International Nuclear Information System (INIS)

Suehiro, S.; Okamoto, K.

2017-01-01

The severe accident evaluation committee of AESJ (Atomic Energy Society of Japan) developed the thermal hydraulic PIRT (Phenomena Identification and Ranking Table) and the source term PIRT based on findings during the Fukushima Daiichi NPPs accident. These PIRTs aimed to explore the debris distribution and the current condition in the NPPs with high accuracy and to extract higher priority from the aspect of the sophistication of the analytical technology to predict the severe accident phenomena by the code. The source term PIRT was divided into 3 phases for the time domain and 9 categories for the spatial domain. The 68 phenomena were extracted and the importance from viewpoint of the source term was ranked through brainstorming and discussion. This paper describes the developed source term PIRT list and summarized the high ranked phenomena in each phase. (author)

The latest results from source term research. Overview and outlook

Energy Technology Data Exchange (ETDEWEB)

Herranz, Luis E. [Centro de Investigaciones Energeticas Medio Ambientales y Tecnologica (CIEMAT), Madrid (Spain); Haste, Tim [Centre d' Etudes de Cadarache, Paul-Lez-Durance (France). Institut de Radioprotection et de Surete Nucleaire (IRSN); Kaerkelae, Teemu [VTT Technical Research Centre of Finland Ltd, Espoo (Finland)

2016-12-15

Source term research has continued internationally for more than 30 years, increasing confidence in calculations of the potential radioactive release to the environment after a severe reactor accident. Important experimental data have been obtained, mainly under international frameworks such as OECD/NEA and EURATOM. Specifically, Phebus FP provides major insights into fission product release and transport. Results are included in severe accident analysis codes. Data from international projects are being interpreted with a view to further improvements in these codes. This paper synthesizes the recent main outcomes from source term research on these topics, and on source term mitigation. It highlights knowledge gaps remaining and discusses ways to proceed. Aside from this further knowledge-driven research, there is consensus on the need to assess the source term predictive ability of current system codes, taking account of scale-up from experiment to reactor conditions.

Source terms derived from analyses of hypothetical accidents, 1950-1986

International Nuclear Information System (INIS)

Stratton, W.R.

1987-01-01

This paper reviews the history of reactor accident source term assumptions. After the Three Mile Island accident, a number of theoretical and experimental studies re-examined possible accident sequences and source terms. Some of these results are summarized in this paper

Spent fuel assembly source term parameters

International Nuclear Information System (INIS)

Barrett, P.R.; Foadian, H.; Rashid, Y.R.; Seager, K.D.; Gianoulakis, S.E.

1993-01-01

Containment of cask contents by a transport cask is a function of the cask body, one or more closure lids, and various bolting hardware, and seals associated with the cavity closure and other containment penetrations. In addition, characteristics of cask contents that impede the ability of radionuclides to move from an origin to the external environment also provide containment. In essence, multiple release barriers exist in series in transport casks, and the magnitude of the releasable activity in the cask is considerably lower than the total activity of its contents. A source term approach accounts for the magnitude of the releasable activity available in the cask by assessing the degree of barrier resistance to release provided by material characteristics and inherent barriers that impede the release of radioactive contents. Standardized methodologies for defining the spent-fuel transport packages with specified regulations have recently been developed. An essential part of applying the source term methodology involves characterizing the response of the spent fuel under regulatory conditions of transport. Thermal and structural models of the cask and fuel are analyzed and used to predict fuel rod failure probabilities. Input to these analyses and failure evaluations cover a wide range of geometrical and material properties. An important issue in the development of these models is the sensitivity of the radioactive source term generated during transport to individual parameters such as temperature and fluence level. This paper provides a summary of sensitivity analyses concentrating on the structural response and failure predictions of the spent fuel assemblies

Unclassified Source Term and Radionuclide Data for Corrective Action Unit 97: Yucca Flat/Climax Mine, Nevada Test Site, Nevada, Revision 1

Energy Technology Data Exchange (ETDEWEB)

Peter Martian

2009-05-01

This report documents the evaluation of the information and data available on the unclassified source term and radionuclide contamination for CAU 97: Yucca Flat/Climax Mine. The total residual inventory of radionuclides associated with one or more tests is known as the radiologic source term (RST). The RST is comprised of radionuclides in water, glass, or other phases or mineralogic forms. The hydrologic source term (HST) of an underground nuclear test is the portion of the total RST that is released into the groundwater over time following the test. In this report, the HST represents radionuclide release some time after the explosion and does not include the rapidly evolving mechanical, thermal, and chemical processes during the explosion. The CAU 97: Yucca Flat/Climax Mine has many more detonations and a wider variety of settings to consider compared to other CAUs. For instance, the source term analysis and evaluation performed for CAUs 101 and 102: Central and Western Pahute Mesa and CAU 98: Frenchman Flat did not consider vadose zone attenuation because many detonations were located near or below the water table. However, the large number of Yucca Flat/Climax Mine tests and the location of many tests above the water table warrant a more robust analysis of the unsaturated zone.

Advisory Committee on human radiation experiments. Supplemental Volume 2a, Sources and documentation appendices. Final report

International Nuclear Information System (INIS)

1995-01-01

This large document provides a catalog of the location of large numbers of reports pertaining to the charge of the Presidential Advisory Committee on Human Radiation Research and is arranged as a series of appendices. Titles of the appendices are Appendix A- Records at the Washington National Records Center Reviewed in Whole or Part by DoD Personnel or Advisory Committee Staff; Appendix B- Brief Descriptions of Records Accessions in the Advisory Committee on Human Radiation Experiments (ACHRE) Research Document Collection; Appendix C- Bibliography of Secondary Sources Used by ACHRE; Appendix D- Brief Descriptions of Human Radiation Experiments Identified by ACHRE, and Indexes; Appendix E- Documents Cited in the ACHRE Final Report and other Separately Described Materials from the ACHRE Document Collection; Appendix F- Schedule of Advisory Committee Meetings and Meeting Documentation; and Appendix G- Technology Note

Advisory Committee on human radiation experiments. Supplemental Volume 2a, Sources and documentation appendices. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-01-01

This large document provides a catalog of the location of large numbers of reports pertaining to the charge of the Presidential Advisory Committee on Human Radiation Research and is arranged as a series of appendices. Titles of the appendices are Appendix A- Records at the Washington National Records Center Reviewed in Whole or Part by DoD Personnel or Advisory Committee Staff; Appendix B- Brief Descriptions of Records Accessions in the Advisory Committee on Human Radiation Experiments (ACHRE) Research Document Collection; Appendix C- Bibliography of Secondary Sources Used by ACHRE; Appendix D- Brief Descriptions of Human Radiation Experiments Identified by ACHRE, and Indexes; Appendix E- Documents Cited in the ACHRE Final Report and other Separately Described Materials from the ACHRE Document Collection; Appendix F- Schedule of Advisory Committee Meetings and Meeting Documentation; and Appendix G- Technology Note.

Comment and response document for the long-term surveillance plan for the Falls City disposal site, Falls City, Texas

International Nuclear Information System (INIS)

1996-11-01

This is the Comment and Response Document dated November 1996 for the Long-Term Surveillance Plan for the Falls City Disposal Site in Falls City, Texas. The site is part of the U.S. DOE's Uranium Mill Tailings Remedial Action Project (UMTRA). Several comments regarding the hydrology and surface erosion described in the Long-Term Surveillance Plan are addressed in this document

Writing in the workplace: Constructing documents using multiple digital sources

Directory of Open Access Journals (Sweden)

Mariëlle Leijten

2014-02-01

Full Text Available In today’s workplaces professional communication often involves constructing documents from multiple digital sources—integrating one’s own texts/graphics with ideas based on others’ text/graphics. This article presents a case study of a professional communication designer as he constructs a proposal over several days. Drawing on keystroke and interview data, we map the professional’s overall process, plot the time course of his writing/design, illustrate how he searches for content and switches among optional digital sources, and show how he modifies and reuses others’ content. The case study reveals not only that the professional (1 searches extensively through multiple sources for content and ideas but that he also (2 constructs visual content (charts, graphs, photographs as well as verbal content, and (3 manages his attention and motivation over this extended task. Since these three activities are not represented in current models of writing, we propose their addition not just to models of communication design, but also to models of writing in general.

76 FR 1173 - Draft Guidance for Industry on Electronic Source Documentation in Clinical Investigations...

Science.gov (United States)

2011-01-07

... Web page at http://www.fda.gov/RegulatoryInformation/Guidances/default.htm . FDA guidances are issued and updated regularly. We recommend you check the Web site to ensure that you have the most up-to-date... electronic diaries provided by study subjects. When paper source documents are available for review, tracing...

FINANCIAL REPORTING AND SOURCE DOCUMENTS OF UKRAINIAN ENTERPRISES WHEN APPLYING THE IFRS

Directory of Open Access Journals (Sweden)

G. Golubnicha

2013-08-01

Full Text Available The theoretical, methodological and practical aspects of changes in financial reporting and source documents specific to Ukrainian enterprises in the new conditions resulting from the application of International Financial Reporting Standards have been analyzed. Also, a conceptual approach of defining the patterns of changes in financial reporting and elements of accounting method has been proposed. The issue of internal quality control of analytical accounting information at various stages of its formation has been researched.

Unclassified Source Term and Radionuclide Data for Corrective Action Unit 98: Frenchman Flat Nevada Test Site, Nevada

International Nuclear Information System (INIS)

Farnham, Irene

2005-01-01

Frenchman Flat is one of several areas of the Nevada Test Site (NTS) used for underground nuclear testing (Figure 1-1). These nuclear tests resulted in groundwater contamination in the vicinity of the underground test areas. As a result, the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO) is currently conducting a corrective action investigation (CAI) of the Frenchman Flat underground test areas. Since 1996, the Nevada Division of Environmental Protection (NDEP) has regulated NNSA/NSO corrective actions through the ''Federal Facility Agreement and Consent Order'' ([FFACO], 1996). Appendix VI of the FFACO agreement, ''Corrective Action Strategy'', was revised on December 7, 2000, and describes the processes that will be used to complete corrective actions, including those in the Underground Test Area (UGTA) Project. The individual locations covered by the agreement are known as corrective action sites (CASs), which are grouped into corrective action units (CAUs). The UGTA CASs are grouped geographically into five CAUs: Frenchman Flat, Central Pahute Mesa, Western Pahute Mesa, Yucca Flat/Climax Mine, and Rainier Mesa/Shoshone Mountain (Figure 1-1). These CAUs have distinctly different contaminant source, geologic, and hydrogeologic characteristics related to their location (FFACO, 1996). The Frenchman Flat CAU consists of 10 CASs located in the northern part of Area 5 and the southern part of Area 11 (Figure 1-1). This report documents the evaluation of the information and data available on the unclassified source term and radionuclide contamination for Frenchman Flat, CAU 98. The methodology used to estimate hydrologic source terms (HSTs) for the Frenchman Flat CAU is also documented. The HST of an underground nuclear test is the portion of the total inventory of radionuclides that is released over time into the groundwater following the test. The total residual inventory of radionuclides associated with one or

The systematic profiling of false identity documents: method validation and performance evaluation using seizures known to originate from common and different sources.

Science.gov (United States)

Baechler, Simon; Terrasse, Vincent; Pujol, Jean-Philippe; Fritz, Thibaud; Ribaux, Olivier; Margot, Pierre

2013-10-10

False identity documents constitute a potential powerful source of forensic intelligence because they are essential elements of transnational crime and provide cover for organized crime. In previous work, a systematic profiling method using false documents' visual features has been built within a forensic intelligence model. In the current study, the comparison process and metrics lying at the heart of this profiling method are described and evaluated. This evaluation takes advantage of 347 false identity documents of four different types seized in two countries whose sources were known to be common or different (following police investigations and dismantling of counterfeit factories). Intra-source and inter-sources variations were evaluated through the computation of more than 7500 similarity scores. The profiling method could thus be validated and its performance assessed using two complementary approaches to measuring type I and type II error rates: a binary classification and the computation of likelihood ratios. Very low error rates were measured across the four document types, demonstrating the validity and robustness of the method to link documents to a common source or to differentiate them. These results pave the way for an operational implementation of a systematic profiling process integrated in a developed forensic intelligence model. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Document understanding for a broad class of documents

NARCIS (Netherlands)

Aiello, Marco; Monz, Christof; Todoran, Leon; Worring, Marcel

2002-01-01

We present a document analysis system able to assign logical labels and extract the reading order in a broad set of documents. All information sources, from geometric features and spatial relations to the textual features and content are employed in the analysis. To deal effectively with these

Spallation Neutron Source Accident Terms for Environmental Impact Statement Input

Energy Technology Data Exchange (ETDEWEB)

Devore, J.R.; Harrington, R.M.

1998-08-01

This report is about accidents with the potential to release radioactive materials into the environment surrounding the Spallation Neutron Source (SNS). As shown in Chap. 2, the inventories of radioactivity at the SNS are dominated by the target facility. Source terms for a wide range of target facility accidents, from anticipated events to worst-case beyond-design-basis events, are provided in Chaps. 3 and 4. The most important criterion applied to these accident source terms is that they should not underestimate potential release. Therefore, conservative methodology was employed for the release estimates. Although the source terms are very conservative, excessive conservatism has been avoided by basing the releases on physical principles. Since it is envisioned that the SNS facility may eventually (after about 10 years) be expanded and modified to support a 4-MW proton beam operational capability, the source terms estimated in this report are applicable to a 4-MW operating proton beam power unless otherwise specified. This is bounding with regard to the 1-MW facility that will be built and operated initially. See further discussion below in Sect. 1.2.

Flowsheets and source terms for radioactive waste projections

International Nuclear Information System (INIS)

Forsberg, C.W.

1985-03-01

Flowsheets and source terms used to generate radioactive waste projections in the Integrated Data Base (IDB) Program are given. Volumes of each waste type generated per unit product throughput have been determined for the following facilities: uranium mining, UF 6 conversion, uranium enrichment, fuel fabrication, boiling-water reactors (BWRs), pressurized-water reactors (PWRs), and fuel reprocessing. Source terms for DOE/defense wastes have been developed. Expected wastes from typical decommissioning operations for each facility type have been determined. All wastes are also characterized by isotopic composition at time of generation and by general chemical composition. 70 references, 21 figures, 53 tables

PHOTOGRAPHY AS DOCUMENT: OTLET AND BRIET’S CONSIDERATIONS

Directory of Open Access Journals (Sweden)

Izângela Maria Sansoni Tonello

2018-04-01

Full Text Available Introduction: The amount and variety of information that are conveyed in different media and means incite a concern, especially in relation to photographic documents, since they are currently the focus of interest of the Information Science field. In this context, this paper emphasizes the role of photographs as sources of information capable of generating knowledge as well as an important aid for research in different areas. Objective: The main goal of this study was to research the concepts and definitions underpinning the photograph as a document in information units. Methodology: Bibliographic and documentary research. Results: It can be affirmed through the meanings about the term document discussed in the literature by the researched authors that the photograph corresponds to the assumptions necessary to substantiate document and photograph in photographic document. Conclusions: It is understood that this study clarifies some issues related to photograph as a document; however, this proposition raises reflections about the importance of the production context as well as its essential relationship with other documents, so that it is indisputably consolidated as a photographic document.

Relation between source term and emergency planning for nuclear power plants

International Nuclear Information System (INIS)

Shi Zhongqi; Yang Ling

1992-01-01

Some background information of the severe accidents and source terms related to the nuclear power plant emergency planning are presented. The new source term information in NUREG-0956 and NUREG-1150, and possible changes in emergency planning requirements in U.S.A. are briefly provided. It is suggested that a principle is used in selecting source terms for establishing the emergency planning policy and a method is used in determining the Emergency Planning Zone (EPZ) size in China. Based on the research results of (1) EPZ size of PWR nuclear power plants being built in China, and (2) impact of reactor size and selected source terms on the EPZ size, it is concluded that the suggested principle and the method are suitable and feasible for PWR nuclear power plants in China

Evolution of source term definition and analysis

International Nuclear Information System (INIS)

Lutz, R.J. Jr.

2004-01-01

The objective of this presentation was to provide an overview of the evolution of accident fission product release analysis methodology and the obtained results; and to provide an overview of the source term implementation analysis in regulatory decisions

Unclassified Source Term and Radionuclide Data for the Groundwater Flow and Contaminant Transport Model of Corrective Action Units 101 and 102: Central and Western Pahute Mesa, Nye County, Nevada, Revision 0

Energy Technology Data Exchange (ETDEWEB)

McCord, John

2004-08-01

This report documents the evaluation of the information and data available on the unclassified source term and radionuclide contamination for Central and Western Pahute Mesa: Corrective Action Units (CAUs) 101 and 102.

Source term estimation during incident response to severe nuclear power plant accidents. Draft

Energy Technology Data Exchange (ETDEWEB)

McKenna, T J; Giitter, J

1987-07-01

The various methods of estimating radionuclide release to the environment (source terms) as a result of an accident at a nuclear power reactor are discussed. The major factors affecting potential radionuclide releases off site (source terms) as a result of nuclear power plant accidents are described. The quantification of these factors based on plant instrumentation also is discussed. A range of accident conditions from those within the design basis to the most severe accidents possible are included in the text. A method of gross estimation of accident source terms and their consequences off site is presented. The goal is to present a method of source term estimation that reflects the current understanding of source term behavior and that can be used during an event. (author)

Source term estimation during incident response to severe nuclear power plant accidents. Draft

International Nuclear Information System (INIS)

McKenna, T.J.; Giitter, J.

1987-01-01

The various methods of estimating radionuclide release to the environment (source terms) as a result of an accident at a nuclear power reactor are discussed. The major factors affecting potential radionuclide releases off site (source terms) as a result of nuclear power plant accidents are described. The quantification of these factors based on plant instrumentation also is discussed. A range of accident conditions from those within the design basis to the most severe accidents possible are included in the text. A method of gross estimation of accident source terms and their consequences off site is presented. The goal is to present a method of source term estimation that reflects the current understanding of source term behavior and that can be used during an event. (author)

Forensic document analysis using scanning microscopy

Science.gov (United States)

Shaffer, Douglas K.

2009-05-01

The authentication and identification of the source of a printed document(s) can be important in forensic investigations involving a wide range of fraudulent materials, including counterfeit currency, travel and identity documents, business and personal checks, money orders, prescription labels, travelers checks, medical records, financial documents and threatening correspondence. The physical and chemical characterization of document materials - including paper, writing inks and printed media - is becoming increasingly relevant for law enforcement agencies, with the availability of a wide variety of sophisticated commercial printers and copiers which are capable of producing fraudulent documents of extremely high print quality, rendering these difficult to distinguish from genuine documents. This paper describes various applications and analytical methodologies using scanning electron miscoscopy/energy dispersive (x-ray) spectroscopy (SEM/EDS) and related technologies for the characterization of fraudulent documents, and illustrates how their morphological and chemical profiles can be compared to (1) authenticate and (2) link forensic documents with a common source(s) in their production history.

Gaz de France. Source document

International Nuclear Information System (INIS)

2005-01-01

This document was issued by Gaz de France, the French gas utility, at the occasion of the opening of the capital of the company. It is intended to shareholders and presents some informations relative to the stocks admitted to Euronext's Eurolist, some general informations about the company and its capital, some informations about the activities of Gaz de France group, about its financial situation and results, about its management, and about its recent evolution and future perspectives. (J.S.)

Determination of source term for Krsko NPP extended fuel cycle

International Nuclear Information System (INIS)

Nemec, T.; Persic, A.; Zagar, T.; Zefran, B.

2004-01-01

The activity and composition of the potential radioactive releases (source term) is important in the decision making about off-site emergency measures in case of a release into environment. Power uprate of Krsko NPP during modernization in 2000 as well as changing of the fuel type and the core design have influenced the source term value. In 2003 a project of 'Jozef Stefan' Institute and Slovenian nuclear safety administration determined a plantspecific source term for new conditions of fuel type and burnup for extended fuel cycle. Calculations of activity and isotopic composition of the core have been performed with ORIGEN-ARP program. Results showed that the core activity for extended 15 months fuel cycle is slightly lower than for the 12 months cycles, mainly due to larger share of fresh fuel. (author)

Glossary of CERCLA-related terms and acronyms

International Nuclear Information System (INIS)

1991-10-01

This glossary contains CERCLA-related terms that are most often encountered in the US Department of Energy (DOE) Environmental Restoration and Emergency Preparedness activities. Detailed definitions are included for key terms. The definitions included in this glossary are taken from the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA), as amended, related federal rulemakings (e.g., 40 CFR 300, National Oil and Hazardous Substances Pollution Contingency Plan), assorted guidance documents prepared by the US Environmental Protection Agency (EPA), and DOE Order 5400.4. The source of each term is noted after the term. Terms presented in this document reflect revised and new definitions published before June 1, 1991. 20 refs

Selective application of revised source terms to operating nuclear power plants

International Nuclear Information System (INIS)

Moon, Joo Hyun; Song, Jae Hyuk; Lee, Young Wook; Ko, Hyun Seok; Kang, Chang Sun

2001-01-01

More than 30 years later since 1962 when TID-14844 was promulgated, there has been big change of the US NRC's regulatory position in using accident source terms for radiological assessment following a design basis accident (DBA). To replace the instantaneous source terms of TID-14844, the time-dependent source terms of NUREG-1465 was published in 1995. In the meantime, the radiological acceptance criteria for reactor site evaluation in 10 CFR Part 100 were also revised. In particular, the concept of total effective dose equivalent has been incorporated in accordance with the radiation protection standards set forth in revised 10 CFR Part 20. Subsequently, the publication of Regulatory Guide 1.183 and the revision of Standard Review Plan 15.0.1 followed in 2000, which provided the licensee of operating nuclear power reactor with the acceptable guidance of applying the revised source term. The guidance allowed the holder of an operating license issued prior to January 10, 1997 to voluntarily revise the accident source terms used in the radiological consequence analyses of DBA. Regarding to its type of application, there suggested full and selective applications, Whether it is full or selective, based upon the scope and nature of associated plant modifications being proposed, the actual application of the revised source terms to an operating plant is expected to give a large impact on its facility design basis. Considering scope and cost of the analyses required for licensing, selective application is seemed to be more appealing to an licensee of the operating plant rather than full application. In this paper, hence, the selective application methodology is reviewed and is actally applied to the assessment of offsite radiological consequence following a LOCA at Ulchin Unit 3 and 4, in order to identify and analyze the potential impacts due to application of revised source terms and to assess the considerations taken in each application prior to its actual

Directional Unfolded Source Term (DUST) for Compton Cameras.

Energy Technology Data Exchange (ETDEWEB)

Mitchell, Dean J.; Mitchell, Dean J.; Horne, Steven M.; O' Brien, Sean; Thoreson, Gregory G

2018-03-01

A Directional Unfolded Source Term (DUST) algorithm was developed to enable improved spectral analysis capabilities using data collected by Compton cameras. Achieving this objective required modification of the detector response function in the Gamma Detector Response and Analysis Software (GADRAS). Experimental data that were collected in support of this work include measurements of calibration sources at a range of separation distances and cylindrical depleted uranium castings.

Development of source term evaluation method for Korean Next Generation Reactor

Energy Technology Data Exchange (ETDEWEB)

Lee, Keon Jae; Cheong, Jae Hak; Park, Jin Baek; Kim, Guk Gee [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of)

1997-10-15

This project had investigate several design features of radioactive waste processing system and method to predict nuclide concentration at primary coolant basic concept of next generation reactor and safety goals at the former phase. In this project several prediction methods of source term are evaluated conglomerately and detailed contents of this project are : model evaluation of nuclide concentration at Reactor Coolant System, evaluation of primary and secondary coolant concentration of reference Nuclear Power Plant(NPP), investigation of prediction parameter of source term evaluation, basic parameter of PWR, operational parameter, respectively, radionuclide removal system and adjustment values of reference NPP, suggestion of source term prediction method of next generation NPP.

Severe accident source term reassessment

International Nuclear Information System (INIS)

Hazzan, M.J.; Gardner, R.; Warman, E.A.; Jacobs, S.B.

1987-01-01

This paper summarizes the status of the reassessment of severe reactor accident source terms, which are defined as the quantity, type, and timing of fission product releases from such accidents. Concentration is on the major results and conclusions of analyses with modern methods for both pressurized water reactors (PWRs) and boiling water reactors (BWRs), and the special case of containment bypass. Some distinctions are drawn between analyses for PWRs and BWRs. In general, the more the matter is examined, the consequences, or probability of serious consequences, seem to be less. (author)

Source term estimation via monitoring data and its implementation to the RODOS system

International Nuclear Information System (INIS)

Bohunova, J.; Duranova, T.

2000-01-01

A methodology and computer code for interpretation of environmental data, i.e. source term assessment, from on-line environmental monitoring network was developed. The method is based on the conversion of measured dose rates to the source term, i.e. airborne radioactivity release rate, taking into account real meteorological data and location of the monitoring points. The bootstrap estimation methodology and bipivot method to estimate the source term from on-site gamma dose rate monitors is used. The mentioned methods provide an estimate of the mean value of the source term and a confidence interval for it. (author)

Evaluation of the Non-Transient Hydrologic Source Term from the CAMBRIC Underground Nuclear Test in Frenchman Flat, Nevada Test Site

International Nuclear Information System (INIS)

Tompson, A B; Maxwell, R M; Carle, S F; Zavarin, M; Pawloski, G A.; Shumaker, D E

2005-01-01

approaches acquired or developed since the previous work (as in Pawloski et al., 2001, at the CHESHIRE site). This will be referred to as the transient CAMBRIC source term. (2) A generic release model made under steady-state flow conditions, in the absence of any transient effect, at the same site with the same RST for use in the development of simple release models at the other nine underground test sites in the Frenchman Flat CAU. This will be referred to as the steady state (non-transient) source term. The purpose of this report is to summarize the results of our steady state source term simulations. Additional details pertaining to these results, the transient model results, and the overall strategy, rationale, and assumptions used in the models will be documented in a separate report

Source term estimation for small sized HTRs

International Nuclear Information System (INIS)

Moormann, R.

1992-08-01

Accidents which have to be considered are core heat-up, reactivity transients, water of air ingress and primary circuit depressurization. The main effort of this paper belongs to water/air ingress and depressurization, which requires consideration of fission product plateout under normal operation conditions; for the latter it is clearly shown, that absorption (penetration) mechanisms are much less important than assumed sometimes in the past. Source term estimation procedures for core heat-up events are shortly reviewed; reactivity transients are apparently covered by them. Besides a general literature survey including identification of areas with insufficient knowledge this paper contains some estimations on the thermomechanical behaviour of fission products in water in air ingress accidents. Typical source term examples are also presented. In an appendix, evaluations of the AVR experiments VAMPYR-I and -II with respect to plateout and fission product filter efficiency are outlined and used for a validation step of the new plateout code SPATRA. (orig.)

Using Bayesian Belief Network (BBN) modelling for Rapid Source Term Prediction. RASTEP Phase 1

International Nuclear Information System (INIS)

Knochenhauer, M.; Swaling, V.H.; Alfheim, P.

2012-09-01

The project is connected to the development of RASTEP, a computerized source term prediction tool aimed at providing a basis for improving off-site emergency management. RASTEP uses Bayesian belief networks (BBN) to model severe accident progression in a nuclear power plant in combination with pre-calculated source terms (i.e., amount, timing, and pathway of released radio-nuclides). The output is a set of possible source terms with associated probabilities. In the NKS project, a number of complex issues associated with the integration of probabilistic and deterministic analyses are addressed. This includes issues related to the method for estimating source terms, signal validation, and sensitivity analysis. One major task within Phase 1 of the project addressed the problem of how to make the source term module flexible enough to give reliable and valid output throughout the accident scenario. Of the alternatives evaluated, it is recommended that RASTEP is connected to a fast running source term prediction code, e.g., MARS, with a possibility of updating source terms based on real-time observations. (Author)

Using Bayesian Belief Network (BBN) modelling for Rapid Source Term Prediction. RASTEP Phase 1

Energy Technology Data Exchange (ETDEWEB)

Knochenhauer, M.; Swaling, V.H.; Alfheim, P. [Scandpower AB, Sundbyberg (Sweden)

2012-09-15

The project is connected to the development of RASTEP, a computerized source term prediction tool aimed at providing a basis for improving off-site emergency management. RASTEP uses Bayesian belief networks (BBN) to model severe accident progression in a nuclear power plant in combination with pre-calculated source terms (i.e., amount, timing, and pathway of released radio-nuclides). The output is a set of possible source terms with associated probabilities. In the NKS project, a number of complex issues associated with the integration of probabilistic and deterministic analyses are addressed. This includes issues related to the method for estimating source terms, signal validation, and sensitivity analysis. One major task within Phase 1 of the project addressed the problem of how to make the source term module flexible enough to give reliable and valid output throughout the accident scenario. Of the alternatives evaluated, it is recommended that RASTEP is connected to a fast running source term prediction code, e.g., MARS, with a possibility of updating source terms based on real-time observations. (Author)

Automatic multimodal detection for long-term seizure documentation in epilepsy.

Science.gov (United States)

Fürbass, F; Kampusch, S; Kaniusas, E; Koren, J; Pirker, S; Hopfengärtner, R; Stefan, H; Kluge, T; Baumgartner, C

2017-08-01

This study investigated sensitivity and false detection rate of a multimodal automatic seizure detection algorithm and the applicability to reduced electrode montages for long-term seizure documentation in epilepsy patients. An automatic seizure detection algorithm based on EEG, EMG, and ECG signals was developed. EEG/ECG recordings of 92 patients from two epilepsy monitoring units including 494 seizures were used to assess detection performance. EMG data were extracted by bandpass filtering of EEG signals. Sensitivity and false detection rate were evaluated for each signal modality and for reduced electrode montages. All focal seizures evolving to bilateral tonic-clonic (BTCS, n=50) and 89% of focal seizures (FS, n=139) were detected. Average sensitivity in temporal lobe epilepsy (TLE) patients was 94% and 74% in extratemporal lobe epilepsy (XTLE) patients. Overall detection sensitivity was 86%. Average false detection rate was 12.8 false detections in 24h (FD/24h) for TLE and 22 FD/24h in XTLE patients. Utilization of 8 frontal and temporal electrodes reduced average sensitivity from 86% to 81%. Our automatic multimodal seizure detection algorithm shows high sensitivity with full and reduced electrode montages. Evaluation of different signal modalities and electrode montages paces the way for semi-automatic seizure documentation systems. Copyright © 2017 International Federation of Clinical Neurophysiology. Published by Elsevier B.V. All rights reserved.

Market Analysis and Consumer Impacts Source Document. Part III. Consumer Behavior and Attitudes Toward Fuel Efficient Vehicles

Science.gov (United States)

1980-12-01

This source document on motor vehicle market analysis and consumer impacts consists of three parts. Part III consists of studies and reviews on: consumer awareness of fuel efficiency issues; consumer acceptance of fuel efficient vehicles; car size ch...

Advisory Committee on human radiation experiments. Final report, Supplemental Volume 2. Sources and documentation

International Nuclear Information System (INIS)

1995-01-01

This volume and its appendixes supplement the Advisory Committee's final report by reporting how we went about looking for information concerning human radiation experiments and intentional releases, a description of what we found and where we found it, and a finding aid for the information that we collected. This volume begins with an overview of federal records, including general descriptions of the types of records that have been useful and how the federal government handles these records. This is followed by an agency-by-agency account of the discovery process and descriptions of the records reviewed, together with instructions on how to obtain further information from those agencies. There is also a description of other sources of information that have been important, including institutional records, print resources, and nonprint media and interviews. The third part contains brief accounts of ACHRE's two major contemporary survey projects (these are described in greater detail in the final report and another supplemental volume) and other research activities. The final section describes how the ACHRE information-nation collections were managed and the records that ACHRE created in the course of its work; this constitutes a general finding aid for the materials deposited with the National Archives. The appendices provide brief references to federal records reviewed, descriptions of the accessions that comprise the ACHRE Research Document Collection, and descriptions of the documents selected for individual treatment. Also included are an account of the documentation available for ACHRE meetings, brief abstracts of the almost 4,000 experiments individually described by ACHRE staff, a full bibliography of secondary sources used, and other information

Advisory Committee on human radiation experiments. Final report, Supplemental Volume 2. Sources and documentation

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-01-01

This volume and its appendixes supplement the Advisory Committee`s final report by reporting how we went about looking for information concerning human radiation experiments and intentional releases, a description of what we found and where we found it, and a finding aid for the information that we collected. This volume begins with an overview of federal records, including general descriptions of the types of records that have been useful and how the federal government handles these records. This is followed by an agency-by-agency account of the discovery process and descriptions of the records reviewed, together with instructions on how to obtain further information from those agencies. There is also a description of other sources of information that have been important, including institutional records, print resources, and nonprint media and interviews. The third part contains brief accounts of ACHRE`s two major contemporary survey projects (these are described in greater detail in the final report and another supplemental volume) and other research activities. The final section describes how the ACHRE information-nation collections were managed and the records that ACHRE created in the course of its work; this constitutes a general finding aid for the materials deposited with the National Archives. The appendices provide brief references to federal records reviewed, descriptions of the accessions that comprise the ACHRE Research Document Collection, and descriptions of the documents selected for individual treatment. Also included are an account of the documentation available for ACHRE meetings, brief abstracts of the almost 4,000 experiments individually described by ACHRE staff, a full bibliography of secondary sources used, and other information.

Development of source term evaluation method for Korean Next Generation Reactor(III)

Energy Technology Data Exchange (ETDEWEB)

Lee, Geon Jae; Park, Jin Baek; Lee, Yeong Il; Song, Min Cheonl; Lee, Ho Jin [Korea Advanced Institue of Science and Technology, Taejon (Korea, Republic of)

1998-06-15

This project had investigated irradiation characteristics of MOX fuel method to predict nuclide concentration at primary and secondary coolant using a core containing 100% of all MOX fuel and development of source term evaluation tool. In this study, several prediction methods of source term are evaluated. Detailed contents of this project are : an evaluation of model for nuclear concentration at Reactor Coolant System, evaluation of primary and secondary coolant concentration of reference Nuclear Power Plant using purely MOX fuel, suggestion of source term prediction method of NPP with a core using MOX fuel.

Glossary of CERCLA, RCRA and TSCA related terms and acronyms

International Nuclear Information System (INIS)

1993-10-01

This glossary contains CERCLA, RCRA and TSCA related terms that are most often encountered in the US Department of Energy (DOE) Environmental Restoration and Emergency Preparedness activities. Detailed definitions are included for key terms. The CERCLA definitions included in this glossary are taken from the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA), as amended and related federal rulemakings. The RCRA definitions included in this glossary are taken from the Resource Conservation and Recovery Act (RCRA) and related federal rulemakings. The TSCA definitions included in this glossary are taken from the Toxic Substances and Control Act (TSCA) and related federal rulemakings. Definitions related to TSCA are limited to those sections in the statute and regulations concerning PCBs and asbestos.Other sources for definitions include additional federal rulemakings, assorted guidance documents prepared by the US Environmental Protection Agency (EPA), guidance and informational documents prepared by the US Department of Energy (DOE), and DOE Orders. The source of each term is noted beside the term. Terms presented in this document reflect revised and new definitions published before July 1, 1993

STACE: Source Term Analyses for Containment Evaluations of transport casks

International Nuclear Information System (INIS)

Seager, K.D.; Gianoulakis, S.E.; Barrett, P.R.; Rashid, Y.R.; Reardon, P.C.

1992-01-01

Following the guidance of ANSI N14.5, the STACE methodology provides a technically defensible means for estimating maximum permissible leakage rates. These containment criteria attempt to reflect the true radiological hazard by performing a detailed examination of the spent fuel, CRUD, and residual contamination contributions to the releasable source term. The evaluation of the spent fuel contribution to the source term has been modeled fairly accurately using the STACE methodology. The structural model predicts the cask drop load history, the mechanical response of the fuel assembly, and the probability of cladding breach. These data are then used to predict the amount of fission gas, volatile species, and fuel fines that are releasable from the cask. There are some areas where data are sparse or lacking (e.g., the quantity and size distribution of fuel rod breaches) in which experimental validation is planned. The CRUD spallation fraction is the major area where no quantitative data has been found; therefore, this also requires experimental validation. In the interim, STACE conservatively assumes a 100% spallation fraction for computing the releasable activity. The source term methodology also conservatively assumes that there is 1 Ci of residual contamination available for release in the transport cask. However, residual contamination is still by far the smallest contributor to the source term activity

DUSTMS-D: DISPOSAL UNIT SOURCE TERM - MULTIPLE SPECIES - DISTRIBUTED FAILURE DATA INPUT GUIDE.

Energy Technology Data Exchange (ETDEWEB)

SULLIVAN, T.M.

2006-01-01

Performance assessment of a low-level waste (LLW) disposal facility begins with an estimation of the rate at which radionuclides migrate out of the facility (i.e., the source term). The focus of this work is to develop a methodology for calculating the source term. In general, the source term is influenced by the radionuclide inventory, the wasteforms and containers used to dispose of the inventory, and the physical processes that lead to release from the facility (fluid flow, container degradation, wasteform leaching, and radionuclide transport). Many of these physical processes are influenced by the design of the disposal facility (e.g., how the engineered barriers control infiltration of water). The complexity of the problem and the absence of appropriate data prevent development of an entirely mechanistic representation of radionuclide release from a disposal facility. Typically, a number of assumptions, based on knowledge of the disposal system, are used to simplify the problem. This has been done and the resulting models have been incorporated into the computer code DUST-MS (Disposal Unit Source Term-Multiple Species). The DUST-MS computer code is designed to model water flow, container degradation, release of contaminants from the wasteform to the contacting solution and transport through the subsurface media. Water flow through the facility over time is modeled using tabular input. Container degradation models include three types of failure rates: (a) instantaneous (all containers in a control volume fail at once), (b) uniformly distributed failures (containers fail at a linear rate between a specified starting and ending time), and (c) gaussian failure rates (containers fail at a rate determined by a mean failure time, standard deviation and gaussian distribution). Wasteform release models include four release mechanisms: (a) rinse with partitioning (inventory is released instantly upon container failure subject to equilibrium partitioning (sorption) with

Source term determination from subcritical multiplication measurements at Koral-1 reactor

International Nuclear Information System (INIS)

Blazquez, J.B.; Barrado, J.M.

1978-01-01

By using an AmBe neutron source two independent procedures have been settled for the zero-power experimental fast-reactor Coral-1 in order to measure the source term which appears in the point kinetical equations. In the first one, the source term is measured when the reactor is just critical with source by taking advantage of the wide range of the linear approach to critical for Coral-1. In the second one, the measurement is made in subcritical state by making use of the previous calibrated control rods. Several applications are also included such as the measurement of the detector dead time, the determinations of the reactivity of small samples and the shape of the neutron importance of the source. (author)

The Einstein Observatory catalog of IPC x ray sources. Volume 1E: Documentation

Science.gov (United States)

Harris, D. E.; Forman, W.; Gioia, I. M.; Hale, J. A.; Harnden, F. R., Jr.; Jones, C.; Karakashian, T.; Maccacaro, T.; Mcsweeney, J. D.; Primini, F. A.

1993-01-01

The Einstein Observatory (HEAO-2, launched November 13, 1978) achieved radically improved sensitivity over previous x-ray missions through the use of focusing optics, which simultaneously afforded greatly reduced background and produced true images. During its 2.5-yr mission, the Einstein X-Ray Telescope was pointed toward some 5,000 celestial targets, most of which were detected, and discovered several thousand additional 'serendipitous' sources in the observed fields. This catalog contains contour diagrams and source data, obtained with the imaging proportional counter in the 0.16 to 3.5 keV energy band, and describes methods for recovering upper limits for any sky position within the observed images. The main catalog consists of six volumes (numbered 2 through 7) of right ascension ordered pages, each containing data for one observation. Along with the primary documentation describing how the catalog was constructed, volume 1 contains a complete source list, results for merged fields, a reference system to published papers, and data useful for calculating upper limits and fluxes.

A Study on Improvement of Algorithm for Source Term Evaluation

International Nuclear Information System (INIS)

Park, Jeong Ho; Park, Do Hyung; Lee, Jae Hee

2010-03-01

The program developed by KAERI for source term assessment of radwastes from the advanced nuclear fuel cycle consists of spent fuel database analysis module, spent fuel arising projection module, and automatic characterization module for radwastes from pyroprocess. To improve the algorithm adopted the developed program, following items were carried out: - development of an algorithm to decrease analysis time for spent fuel database - development of setup routine for a analysis procedure - improvement of interface for spent fuel arising projection module - optimization of data management algorithm needed for massive calculation to estimate source terms of radwastes from advanced fuel cycle The program developed through this study has a capability to perform source term estimation although several spent fuel assemblies with different fuel design, initial enrichment, irradiation history, discharge burnup, and cooling time are processed at the same time in the pyroprocess. It is expected that this program will be very useful for the design of unit process of pyroprocess and disposal system

Source terms in relation to air cleaning

International Nuclear Information System (INIS)

Bernero, R.M.

1985-01-01

There are two sets of source terms for consideration in air cleaning, those for routine releases and those for accident releases. With about 1000 reactor years of commercial operating experience in the US done, there is an excellent data base for routine and expected transient releases. Specifications for air cleaning can be based on this body of experience with confidence. Specifications for air cleaning in accident situations is another matter. Recent investigations of severe accident behavior are offering a new basis for source terms and air cleaning specifications. Reports by many experts in the field describe an accident environment notably different from previous models. It is an atmosphere heavy with aerosols, both radioactive and inert. Temperatures are sometimes very high; radioiodine is typically in the form of cesium iodide aerosol particles; other nuclides, such as tellurium, are also important aerosols. Some of the present air cleaning requirements may be very important in light of these new accident behavior models. Others may be wasteful or even counterproductive. The use of the new data on accident behavior models to reevaluate requirements promptly is discussed

Document organization by means of graphs

Directory of Open Access Journals (Sweden)

Santa Vallejo Figueroa

2016-12-01

Full Text Available Nowadays documents are the main way to represent information and knowledge in several domains. Continuously users store documents in hard disk or online media according to some personal organization based on topics, but such documents can contain one or more topics. This situation makes hard to access documents when is required. The current search engines are based on the name of file or content, but where the desired term or terms must match exactly as are in the content. In this paper, a method for organize documents by means of graphs is proposed, taking into account the topics of the documents. For this a graph for each document is generated taking into account synonyms, semantic related terms, hyponyms, and hypernyms of nouns and verbs contained in documents. The proposal have been compares against Google Desktop and LogicalDoc with interesting results.

Unclassified Source Term and Radionuclide Data for Corrective Action Unit 98: Frenchman Flat Nevada Test Site, Nevada, Rev. No.: 0

Energy Technology Data Exchange (ETDEWEB)

Farnham, Irene

2005-09-01

Frenchman Flat is one of several areas of the Nevada Test Site (NTS) used for underground nuclear testing (Figure 1-1). These nuclear tests resulted in groundwater contamination in the vicinity of the underground test areas. As a result, the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO) is currently conducting a corrective action investigation (CAI) of the Frenchman Flat underground test areas. Since 1996, the Nevada Division of Environmental Protection (NDEP) has regulated NNSA/NSO corrective actions through the ''Federal Facility Agreement and Consent Order'' ([FFACO], 1996). Appendix VI of the FFACO agreement, ''Corrective Action Strategy'', was revised on December 7, 2000, and describes the processes that will be used to complete corrective actions, including those in the Underground Test Area (UGTA) Project. The individual locations covered by the agreement are known as corrective action sites (CASs), which are grouped into corrective action units (CAUs). The UGTA CASs are grouped geographically into five CAUs: Frenchman Flat, Central Pahute Mesa, Western Pahute Mesa, Yucca Flat/Climax Mine, and Rainier Mesa/Shoshone Mountain (Figure 1-1). These CAUs have distinctly different contaminant source, geologic, and hydrogeologic characteristics related to their location (FFACO, 1996). The Frenchman Flat CAU consists of 10 CASs located in the northern part of Area 5 and the southern part of Area 11 (Figure 1-1). This report documents the evaluation of the information and data available on the unclassified source term and radionuclide contamination for Frenchman Flat, CAU 98. The methodology used to estimate hydrologic source terms (HSTs) for the Frenchman Flat CAU is also documented. The HST of an underground nuclear test is the portion of the total inventory of radionuclides that is released over time into the groundwater following the test. The total residual inventory

Reassessment of the technical bases for estimating source terms. Draft report for comment

International Nuclear Information System (INIS)

Silberberg, M.; Mitchell, J.A.; Meyer, R.O.; Pasedag, W.F.; Ryder, C.P.; Peabody, C.A.; Jankowski, M.W.

1985-07-01

NUREG-0956 describes the NRC staff and contractor efforts to reassess and update the agency's analytical procedures for estimating accident source terms for nuclear power plants. The effort included development of a new source term analytical procedure - a set of computer codes - that is intended to replace the methodology of the Reactor Safety Study (WASH-1400) and to be used in reassessing the use of TID-14844 assumptions (10 CFR 100). NUREG-0956 describes the development of these codes, the demonstration of the codes to calculate source terms for specific cases, the peer review of this work, some perspectives on the overall impact of new source terms on plant risks, the plans for related research projects, and the conclusions and recommendations resulting from the effort

Pennsylvania Source Term Tracking System

International Nuclear Information System (INIS)

1992-08-01

The Pennsylvania Source Term Tracking System tabulates surveys received from radioactive waste generators in the Commonwealth of radioactive waste is collected each quarter from generators using the Low-Level Radioactive Waste Management Quarterly Report Form (hereafter called the survey) and then entered into the tracking system data base. This personal computer-based tracking system can generate 12 types of tracking reports. The first four sections of this reference manual supply complete instructions for installing and setting up the tracking system on a PC. Section 5 presents instructions for entering quarterly survey data, and Section 6 discusses generating reports. The appendix includes samples of each report

Analysis and classification of oncology activities on the way to workflow based single source documentation in clinical information systems.

Science.gov (United States)

Wagner, Stefan; Beckmann, Matthias W; Wullich, Bernd; Seggewies, Christof; Ries, Markus; Bürkle, Thomas; Prokosch, Hans-Ulrich

2015-12-22

Today, cancer documentation is still a tedious task involving many different information systems even within a single institution and it is rarely supported by appropriate documentation workflows. In a comprehensive 14 step analysis we compiled diagnostic and therapeutic pathways for 13 cancer entities using a mixed approach of document analysis, workflow analysis, expert interviews, workflow modelling and feedback loops. These pathways were stepwise classified and categorized to create a final set of grouped pathways and workflows including electronic documentation forms. A total of 73 workflows for the 13 entities based on 82 paper documentation forms additionally to computer based documentation systems were compiled in a 724 page document comprising 130 figures, 94 tables and 23 tumour classifications as well as 12 follow-up tables. Stepwise classification made it possible to derive grouped diagnostic and therapeutic pathways for the three major classes - solid entities with surgical therapy - solid entities with surgical and additional therapeutic activities and - non-solid entities. For these classes it was possible to deduct common documentation workflows to support workflow-guided single-source documentation. Clinical documentation activities within a Comprehensive Cancer Center can likely be realized in a set of three documentation workflows with conditional branching in a modern workflow supporting clinical information system.

Using Bayesian Belief Network (BBN) modelling for rapid source term prediction. Final report

Energy Technology Data Exchange (ETDEWEB)

Knochenhauer, M.; Swaling, V.H.; Dedda, F.D.; Hansson, F.; Sjoekvist, S.; Sunnegaerd, K. [Lloyd' s Register Consulting AB, Sundbyberg (Sweden)

2013-10-15

The project presented in this report deals with a number of complex issues related to the development of a tool for rapid source term prediction (RASTEP), based on a plant model represented as a Bayesian belief network (BBN) and a source term module which is used for assigning relevant source terms to BBN end states. Thus, RASTEP uses a BBN to model severe accident progression in a nuclear power plant in combination with pre-calculated source terms (i.e., amount, composition, timing, and release path of released radio-nuclides). The output is a set of possible source terms with associated probabilities. One major issue has been associated with the integration of probabilistic and deterministic analyses are addressed, dealing with the challenge of making the source term determination flexible enough to give reliable and valid output throughout the accident scenario. The potential for connecting RASTEP to a fast running source term prediction code has been explored, as well as alternative ways of improving the deterministic connections of the tool. As part of the investigation, a comparison of two deterministic severe accident analysis codes has been performed. A second important task has been to develop a general method where experts' beliefs can be included in a systematic way when defining the conditional probability tables (CPTs) in the BBN. The proposed method includes expert judgement in a systematic way when defining the CPTs of a BBN. Using this iterative method results in a reliable BBN even though expert judgements, with their associated uncertainties, have been used. It also simplifies verification and validation of the considerable amounts of quantitative data included in a BBN. (Author)

Using Bayesian Belief Network (BBN) modelling for rapid source term prediction. Final report

International Nuclear Information System (INIS)

Knochenhauer, M.; Swaling, V.H.; Dedda, F.D.; Hansson, F.; Sjoekvist, S.; Sunnegaerd, K.

2013-10-01

The project presented in this report deals with a number of complex issues related to the development of a tool for rapid source term prediction (RASTEP), based on a plant model represented as a Bayesian belief network (BBN) and a source term module which is used for assigning relevant source terms to BBN end states. Thus, RASTEP uses a BBN to model severe accident progression in a nuclear power plant in combination with pre-calculated source terms (i.e., amount, composition, timing, and release path of released radio-nuclides). The output is a set of possible source terms with associated probabilities. One major issue has been associated with the integration of probabilistic and deterministic analyses are addressed, dealing with the challenge of making the source term determination flexible enough to give reliable and valid output throughout the accident scenario. The potential for connecting RASTEP to a fast running source term prediction code has been explored, as well as alternative ways of improving the deterministic connections of the tool. As part of the investigation, a comparison of two deterministic severe accident analysis codes has been performed. A second important task has been to develop a general method where experts' beliefs can be included in a systematic way when defining the conditional probability tables (CPTs) in the BBN. The proposed method includes expert judgement in a systematic way when defining the CPTs of a BBN. Using this iterative method results in a reliable BBN even though expert judgements, with their associated uncertainties, have been used. It also simplifies verification and validation of the considerable amounts of quantitative data included in a BBN. (Author)

Source term model evaluations for the low-level waste facility performance assessment

Energy Technology Data Exchange (ETDEWEB)

Yim, M.S.; Su, S.I. [North Carolina State Univ., Raleigh, NC (United States)

1995-12-31

The estimation of release of radionuclides from various waste forms to the bottom boundary of the waste disposal facility (source term) is one of the most important aspects of LLW facility performance assessment. In this work, several currently used source term models are comparatively evaluated for the release of carbon-14 based on a test case problem. The models compared include PRESTO-EPA-CPG, IMPACTS, DUST and NEFTRAN-II. Major differences in assumptions and approaches between the models are described and key parameters are identified through sensitivity analysis. The source term results from different models are compared and other concerns or suggestions are discussed.

An investigation of the closure problem applied to reactor accident source terms

International Nuclear Information System (INIS)

Brearley, I.R.; Nixon, W.; Hayns, M.R.

1987-01-01

The closure problem, as considered here, focuses attention on the question of when in current research programmes enough has been learned about the source terms for reactor accident releases. Noting that current research is tending to reduce the estimated magnitude of the aerosol component of atmospheric, accidental releases, several possible criteria for closure are suggested. Moreover, using the reactor accident consequence model CRACUK, the effect of gradually reducing the aerosol release fractions of a pressurized water reactor (PWR2) source term (as defined in the WASH-1400 study) is investigated and the implications of applying the suggested criteria to current source term research discussed. (author)

Data assimilation and source term estimation during the early phase of a nuclear accident

Energy Technology Data Exchange (ETDEWEB)

Golubenkov, A.; Borodin, R. [SPA Typhoon, Emergency Centre (Russian Federation); Sohier, A.; Rojas Palma, C. [Centre de l`Etude de l`Energie Nucleaire, Mol (Belgium)

1996-02-01

The mathematical/physical base of possible methods to model the source term during an accidental release of radionuclides is discussed. Knowledge of the source term is important in view of optimizing urgent countermeasures to the population. In most cases however, it will be impossible to assess directly the release dynamics. Therefore methods are under development in which the source term is modelled, based on the comparison of off-site monitoring data and model predictions using an atmospheric dispersion model. The degree of agreement between the measured and calculated characteristics of the radioactive contamination of the air and the ground surface is an important criterion in this process. Due to the inherent complexity, some geometrical transformations taking space-time discrepancies between observed and modelled contamination fields are defined before the source term is adapted. This work describes the developed algorithms which are also tested against data from some tracer experiments performed in the past. This method is also used to reconstruct the dynamics of the Chernobyl source term. Finally this report presents a concept of software to reconstruct a multi-isotopic source term in real-time.

Data assimilation and source term estimation during the early phase of a nuclear accident

International Nuclear Information System (INIS)

Golubenkov, A.; Borodin, R.; Sohier, A.; Rojas Palma, C.

1996-02-01

The mathematical/physical base of possible methods to model the source term during an accidental release of radionuclides is discussed. Knowledge of the source term is important in view of optimizing urgent countermeasures to the population. In most cases however, it will be impossible to assess directly the release dynamics. Therefore methods are under development in which the source term is modelled, based on the comparison of off-site monitoring data and model predictions using an atmospheric dispersion model. The degree of agreement between the measured and calculated characteristics of the radioactive contamination of the air and the ground surface is an important criterion in this process. Due to the inherent complexity, some geometrical transformations taking space-time discrepancies between observed and modelled contamination fields are defined before the source term is adapted. This work describes the developed algorithms which are also tested against data from some tracer experiments performed in the past. This method is also used to reconstruct the dynamics of the Chernobyl source term. Finally this report presents a concept of software to reconstruct a multi-isotopic source term in real-time

Revised reactor accident source terms in the U.S. and implementation for light water reactors

International Nuclear Information System (INIS)

Soffer, L.; Lee, J.Y.

1992-01-01

Current NRC reactor accident source terms used for licensing are contained in Regulatory Guides 1.3 and 1.4 and specify that 100 % of the core inventory of noble gases and 25 % of the iodine fission products are assumed to be instantaneously available for release from the containment. The chemical form of the iodine fission products is also assumed to be predominantly elemental (I 2 ) iodine. These assumptions have strongly affected present nuclear plant designs. Severe accident research results have confirmed that although the current source term is very substantial and has resulted in a very high level of plant capability, the present source term is no longer compatible with a realistic understanding of severe accidents. The NRC has issued a proposed revision of the reactor accident source terms as part of several regulatory activities to incorporate severe accident insights for future plants. A revision to 10 CFR 100 is also being proposed to specify site criteria directly and to eliminate source terms and doses for site evaluation. Reactor source terms will continue to be important in evaluating plant designs. Although intended primarily for future plants, existing and evolutionary power plants may voluntarily apply revised accident source term insights as well in licensing. The proposed revised accident source terms are presented in terms of fission product composition, magnitude, timing and iodine chemical form. Some implications for light water reactors are discussed. (author)

EDF source term reduction project main outcomes and further developments

International Nuclear Information System (INIS)

Ranchoux, Gilles; Bonnefon, Julien; Benfarah, Moez; Wintergerst Matthieu; Gressier, Frederic; Leclercq, Stephanie

2012-09-01

The dose reduction is a strategic purpose for EDF in link with the stakes of, nuclear acceptability, respect of regulation and productivity gains. This consists not only in improving the reactor shutdown organization (time spent in control area, biological shielding,...) but also in improving the radiological state of the unit and the efficiency of the source term reduction operations. Since 2003, EDF has been running an innovative project called 'Source Term Reduction' federating the different EDF research and engineering centers in order to: - participate to the long term view about Radiological Protection issues (international feedback analyses), - develop contamination prediction tools (OSCAR software) suitable for the industrial needs (operating units and EPR design), - develop scientific models useful for the understanding of contamination mechanisms to support the strategic decision processes, - carry on with updating and analyzing of contamination measurements feedback in corrosion products (EMECC and CZT campaigns), - carry on with the operational support at short or middle term by optimizing startup and shutdown processes, pre-oxidation or and by improving purification efficiency or material characteristics. This paper will show in a first part the main 2011 results in occupational exposure (collective and individual dose, RCS index...). In a second part, an overview of the main EDF outcomes of the last 3 years in the field of source term reduction will be presented. Future developments extended to contamination issues in EDF NPPs will be also pointed out in this paper. (authors)

Backup Sourcing Decisions for Coping with Supply Disruptions under Long-Term Horizons

Directory of Open Access Journals (Sweden)

Jing Hou

2016-01-01

Full Text Available This paper studies a buyer’s inventory control problem under a long-term horizon. The buyer has one major supplier that is prone to disruption risks and one backup supplier with higher wholesale price. Two kinds of sourcing methods are available for the buyer: single sourcing with/without contingent supply and dual sourcing. In contingent sourcing, the backup supplier is capacitated and/or has yield uncertainty, whereas in dual sourcing the backup supplier has an incentive to offer output flexibility during disrupted periods. The buyer’s expected cost functions and the optimal base-stock levels using each sourcing method under long-term horizon are obtained, respectively. The effects of three risk parameters, disruption probability, contingent capacity or uncertainty, and backup flexibility, are examined using comparative studies and numerical computations. Four sourcing methods, namely, single sourcing with contingent supply, dual sourcing, and single sourcing from either of the two suppliers, are also compared. These findings can be used as a valuable guideline for companies to select an appropriate sourcing strategy under supply disruption risks.

Reevaluation of HFIR source term: Supplement 2

International Nuclear Information System (INIS)

Thomas, W.E.

1986-11-01

The HFIR source term has been reevaluated to assess the impact of the increase in core lifetime from 15 to 24 days. Calculations were made to determine the nuclide activities of the iodines, noble gases, and other fission products. The results show that there is no significant change in off-site dose due to the increased fuel cycle for the release scenario postulated in ORNL-3573

Toward Documentation of Program Evolution

DEFF Research Database (Denmark)

Vestdam, Thomas; Nørmark, Kurt

2005-01-01

The documentation of a program often falls behind the evolution of the program source files. When this happens it may be attractive to shift the documentation mode from updating the documentation to documenting the evolution of the program. This paper describes tools that support the documentatio....... It is concluded that our approach can help revitalize older documentation, and that discovery of the fine grained program evolution steps help the programmer in documenting the evolution of the program....

Glossary of CERCLA, RCRA and TSCA related terms and acronyms. Environmental Guidance

Energy Technology Data Exchange (ETDEWEB)

1993-10-01

This glossary contains CERCLA, RCRA and TSCA related terms that are most often encountered in the US Department of Energy (DOE) Environmental Restoration and Emergency Preparedness activities. Detailed definitions are included for key terms. The CERCLA definitions included in this glossary are taken from the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA), as amended and related federal rulemakings. The RCRA definitions included in this glossary are taken from the Resource Conservation and Recovery Act (RCRA) and related federal rulemakings. The TSCA definitions included in this glossary are taken from the Toxic Substances and Control Act (TSCA) and related federal rulemakings. Definitions related to TSCA are limited to those sections in the statute and regulations concerning PCBs and asbestos.Other sources for definitions include additional federal rulemakings, assorted guidance documents prepared by the US Environmental Protection Agency (EPA), guidance and informational documents prepared by the US Department of Energy (DOE), and DOE Orders. The source of each term is noted beside the term. Terms presented in this document reflect revised and new definitions published before July 1, 1993.

Evaluation of the LMFBR cover gas source term and synthesis of the associated R and D

International Nuclear Information System (INIS)

Balard, F.; Carluec, B.

1996-01-01

At the end of the seventies and the beginning of the eighties, there appeared a pressing need of experimental results to assess the LMFBR's safety level. Because of the urgency, analytical studies were not systematically undertaken and maximum credible cover gas instantaneous source terms (radionuclides core release fraction) were got directly from crude out-of-pile experiment interpretations. Two types of studies and mock-ups were undertaken depending on the timescale of the phenomena: instantaneous source terms (corresponding to an unlikely energetic core disruptive accident CDA), and delayed ones (tens of minutes to some hours). The experiments performed in this frame are reviewed in this presentation: 1) instantaneous source term: - FAUST experiments: I, Cs, UO2 source terms (FzK, Germany), - FAST experiments : pool depth influence on non volatile source term (USA), - CARAVELLE experiments: nonvolatile source term in SPX1 geometry (CEA, France); 2) delayed source term: - NALA experiments: I, Cs, Sr, UO2 source term (FzK, Germany), - PAVE experiments: I source term (CEA, France), - NACOWA experiments: cover gas aerosols enrichment in I and Cs (FzK, Germany) - other French experiments in COPACABANA and GULLIVER facilities. The volatile fission products release is tightly bound to sodium evaporation and a large part of the fission products is dissolved in the liquid sodium aerosols present in the cover gas. Thus the knowledge of the amount of aerosol release to the cover gas is important for the evaluation of the source term. The maximum credible cover gas instantaneous source terms deduced from the experiments have led to conservative source terms to be taken into account in safety analysis. Nevertheless modelling attempts of the observed (in-pile or out-of-pile) physico-chemical phenomena have been undertaken for extrapolation to the reactor case. The main topics of this theoretical research are as follows: fission products evaporation in the cover gas (Fz

Market Analysis and Consumer Impacts Source Document. Part I. The Motor Vehicle Market in the Late 1970's

Science.gov (United States)

1980-12-01

The source document on motor vehicle market analysis and consumer impact consists of three parts. Part I is an integrated overview of the motor vehicle market in the late 1970's, with sections on the structure of the market, motor vehicle trends, con...

A nuclear source term analysis for spacecraft power systems

International Nuclear Information System (INIS)

McCulloch, W.H.

1998-01-01

All US space missions involving on board nuclear material must be approved by the Office of the President. To be approved the mission and the hardware systems must undergo evaluations of the associated nuclear health and safety risk. One part of these evaluations is the characterization of the source terms, i.e., the estimate of the amount, physical form, and location of nuclear material, which might be released into the environment in the event of credible accidents. This paper presents a brief overview of the source term analysis by the Interagency Nuclear Safety Review Panel for the NASA Cassini Space Mission launched in October 1997. Included is a description of the Energy Interaction Model, an innovative approach to the analysis of potential releases from high velocity impacts resulting from launch aborts and reentries

PFLOTRAN-RepoTREND Source Term Comparison Summary.

Energy Technology Data Exchange (ETDEWEB)

Frederick, Jennifer M

2018-03-01

Code inter-comparison studies are useful exercises to verify and benchmark independently developed software to ensure proper function, especially when the software is used to model high-consequence systems which cannot be physically tested in a fully representative environment. This summary describes the results of the first portion of the code inter-comparison between PFLOTRAN and RepoTREND, which compares the radionuclide source term used in a typical performance assessment.

Low-level waste disposal performance assessments - Total source-term analysis

Energy Technology Data Exchange (ETDEWEB)

Wilhite, E.L.

1995-12-31

Disposal of low-level radioactive waste at Department of Energy (DOE) facilities is regulated by DOE. DOE Order 5820.2A establishes policies, guidelines, and minimum requirements for managing radioactive waste. Requirements for disposal of low-level waste emplaced after September 1988 include providing reasonable assurance of meeting stated performance objectives by completing a radiological performance assessment. Recently, the Defense Nuclear Facilities Safety Board issued Recommendation 94-2, {open_quotes}Conformance with Safety Standards at Department of Energy Low-Level Nuclear Waste and Disposal Sites.{close_quotes} One of the elements of the recommendation is that low-level waste performance assessments do not include the entire source term because low-level waste emplaced prior to September 1988, as well as other DOE sources of radioactivity in the ground, are excluded. DOE has developed and issued guidance for preliminary assessments of the impact of including the total source term in performance assessments. This paper will present issues resulting from the inclusion of all DOE sources of radioactivity in performance assessments of low-level waste disposal facilities.

Gaz de France. Source document; Gaz de France. Document de base

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-07-01

This document was issued by Gaz de France, the French gas utility, at the occasion of the opening of the capital of the company. It is intended to shareholders and presents some informations relative to the stocks admitted to Euronext's Eurolist, some general informations about the company and its capital, some informations about the activities of Gaz de France group, about its financial situation and results, about its management, and about its recent evolution and future perspectives. (J.S.)

Regulatory Technology Development Plan - Sodium Fast Reactor: Mechanistic Source Term - Trial Calculation

International Nuclear Information System (INIS)

Grabaskas, David

2016-01-01

The potential release of radioactive material during a plant incident, referred to as the source term, is a vital design metric and will be a major focus of advanced reactor licensing. The U.S. Nuclear Regulatory Commission has stated an expectation for advanced reactor vendors to present a mechanistic assessment of the potential source term in their license applications. The mechanistic source term presents an opportunity for vendors to realistically assess the radiological consequences of an incident, and may allow reduced emergency planning zones and smaller plant sites. However, the development of a mechanistic source term for advanced reactors is not without challenges, as there are often numerous phenomena impacting the transportation and retention of radionuclides. This project sought to evaluate U.S. capabilities regarding the mechanistic assessment of radionuclide release from core damage incidents at metal fueled, pool-type sodium fast reactors (SFRs). The purpose of the analysis was to identify, and prioritize, any gaps regarding computational tools or data necessary for the modeling of radionuclide transport and retention phenomena. To accomplish this task, a parallel-path analysis approach was utilized. One path, led by Argonne and Sandia National Laboratories, sought to perform a mechanistic source term assessment using available codes, data, and models, with the goal to identify gaps in the current knowledge base. The second path, performed by an independent contractor, performed sensitivity analyses to determine the importance of particular radionuclides and transport phenomena in regards to offsite consequences. The results of the two pathways were combined to prioritize gaps in current capabilities.

Low-level radioactive waste source terms for the 1992 integrated data base

International Nuclear Information System (INIS)

Loghry, S.L.; Kibbey, A.H.; Godbee, H.W.; Icenhour, A.S.; DePaoli, S.M.

1995-01-01

This technical manual presents updated generic source terms (i.e., unitized amounts and radionuclide compositions) which have been developed for use in the Integrated Data Base (IDB) Program of the U.S. Department of Energy (DOE). These source terms were used in the IDB annual report, Integrated Data Base for 1992: Spent Fuel and Radioactive Waste Inventories, Projections, and Characteristics, DOE/RW-0006, Rev. 8, October 1992. They are useful as a basis for projecting future amounts (volume and radioactivity) of low-level radioactive waste (LLW) shipped for disposal at commercial burial grounds or sent for storage at DOE solid-waste sites. Commercial fuel cycle LLW categories include boiling-water reactor, pressurized-water reactor, fuel fabrication, and uranium hexafluoride (UF 6 ) conversion. Commercial nonfuel cycle LLW includes institutional/industrial (I/I) waste. The LLW from DOE operations is category as uranium/thorium fission product, induced activity, tritium, alpha, and open-quotes otherclose quotes. Fuel cycle commercial LLW source terms are normalized on the basis of net electrical output [MW(e)-year], except for UF 6 conversion, which is normalized on the basis of heavy metal requirement [metric tons of initial heavy metal ]. The nonfuel cycle commercial LLW source term is normalized on the basis of volume (cubic meters) and radioactivity (curies) for each subclass within the I/I category. The DOE LLW is normalized in a manner similar to that for commercial I/I waste. The revised source terms are based on the best available historical data through 1992

Impact of source terms on distances to which reactor accident consequences occur

International Nuclear Information System (INIS)

Ostmeyer, R.M.

1982-01-01

Estimates of the distances over which reactor accident consequences might occur are important for development of siting criteria and for emergency response planning. This paper summarizes the results of a series of CRAC2 calculations performed to estimate these distances. Because of the current controversy concerning the magnitude of source terms for severe accidents, the impact of source term reductions upon distance estimates is also examined

The long-term problems of contaminated land: Sources, impacts and countermeasures

International Nuclear Information System (INIS)

Baes, C.F. III.

1986-11-01

This report examines the various sources of radiological land contamination; its extent; its impacts on man, agriculture, and the environment; countermeasures for mitigating exposures; radiological standards; alternatives for achieving land decontamination and cleanup; and possible alternatives for utilizing the land. The major potential sources of extensive long-term land contamination with radionuclides, in order of decreasing extent, are nuclear war, detonation of a single nuclear weapon (e.g., a terrorist act), serious reactor accidents, and nonfission nuclear weapons accidents that disperse the nuclear fuels (termed ''broken arrows'')

Using Reactive Transport Modeling to Evaluate the Source Term at Yucca Mountain

Energy Technology Data Exchange (ETDEWEB)

Y. Chen

2001-12-19

The conventional approach of source-term evaluation for performance assessment of nuclear waste repositories uses speciation-solubility modeling tools and assumes pure phases of radioelements control their solubility. This assumption may not reflect reality, as most radioelements (except for U) may not form their own pure phases. As a result, solubility limits predicted using the conventional approach are several orders of magnitude higher then the concentrations of radioelements measured in spent fuel dissolution experiments. This paper presents the author's attempt of using a non-conventional approach to evaluate source term of radionuclide release for Yucca Mountain. Based on the general reactive-transport code AREST-CT, a model for spent fuel dissolution and secondary phase precipitation has been constructed. The model accounts for both equilibrium and kinetic reactions. Its predictions have been compared against laboratory experiments and natural analogues. It is found that without calibrations, the simulated results match laboratory and field observations very well in many aspects. More important is the fact that no contradictions between them have been found. This provides confidence in the predictive power of the model. Based on the concept of Np incorporated into uranyl minerals, the model not only predicts a lower Np source-term than that given by conventional Np solubility models, but also produces results which are consistent with laboratory measurements and observations. Moreover, two hypotheses, whether Np enters tertiary uranyl minerals or not, have been tested by comparing model predictions against laboratory observations, the results favor the former. It is concluded that this non-conventional approach of source term evaluation not only eliminates over-conservatism in conventional solubility approach to some extent, but also gives a realistic representation of the system of interest, which is a prerequisite for truly understanding the long-term

Using Reactive Transport Modeling to Evaluate the Source Term at Yucca Mountain

International Nuclear Information System (INIS)

Y. Chen

2001-01-01

The conventional approach of source-term evaluation for performance assessment of nuclear waste repositories uses speciation-solubility modeling tools and assumes pure phases of radioelements control their solubility. This assumption may not reflect reality, as most radioelements (except for U) may not form their own pure phases. As a result, solubility limits predicted using the conventional approach are several orders of magnitude higher then the concentrations of radioelements measured in spent fuel dissolution experiments. This paper presents the author's attempt of using a non-conventional approach to evaluate source term of radionuclide release for Yucca Mountain. Based on the general reactive-transport code AREST-CT, a model for spent fuel dissolution and secondary phase precipitation has been constructed. The model accounts for both equilibrium and kinetic reactions. Its predictions have been compared against laboratory experiments and natural analogues. It is found that without calibrations, the simulated results match laboratory and field observations very well in many aspects. More important is the fact that no contradictions between them have been found. This provides confidence in the predictive power of the model. Based on the concept of Np incorporated into uranyl minerals, the model not only predicts a lower Np source-term than that given by conventional Np solubility models, but also produces results which are consistent with laboratory measurements and observations. Moreover, two hypotheses, whether Np enters tertiary uranyl minerals or not, have been tested by comparing model predictions against laboratory observations, the results favor the former. It is concluded that this non-conventional approach of source term evaluation not only eliminates over-conservatism in conventional solubility approach to some extent, but also gives a realistic representation of the system of interest, which is a prerequisite for truly understanding the long-term

Expert consensus document: Mind the gaps—advancing research into short-term and long-term neuropsychological outcomes of youth sports-related concussions.

Science.gov (United States)

Carman, Aaron J; Ferguson, Rennie; Cantu, Robert; Comstock, R Dawn; Dacks, Penny A; DeKosky, Steven T; Gandy, Sam; Gilbert, James; Gilliland, Chad; Gioia, Gerard; Giza, Christopher; Greicius, Michael; Hainline, Brian; Hayes, Ronald L; Hendrix, James; Jordan, Barry; Kovach, James; Lane, Rachel F; Mannix, Rebekah; Murray, Thomas; Seifert, Tad; Shineman, Diana W; Warren, Eric; Wilde, Elisabeth; Willard, Huntington; Fillit, Howard M

2015-04-01

Sports-related concussions and repetitive subconcussive exposure are increasingly recognized as potential dangers to paediatric populations, but much remains unknown about the short-term and long-term consequences of these events, including potential cognitive impairment and risk of later-life dementia. This Expert Consensus Document is the result of a 1-day meeting convened by Safe Kids Worldwide, the Alzheimer's Drug Discovery Foundation, and the Andrews Institute for Orthopaedics and Sports Medicine. The goal is to highlight knowledge gaps and areas of critically needed research in the areas of concussion science, dementia, genetics, diagnostic and prognostic biomarkers, neuroimaging, sports injury surveillance, and information sharing. For each of these areas, we propose clear and achievable paths to improve the understanding, treatment and prevention of youth sports-related concussions.

The long-term problems of contaminated land: Sources, impacts and countermeasures

Energy Technology Data Exchange (ETDEWEB)

Baes, C.F. III

1986-11-01

This report examines the various sources of radiological land contamination; its extent; its impacts on man, agriculture, and the environment; countermeasures for mitigating exposures; radiological standards; alternatives for achieving land decontamination and cleanup; and possible alternatives for utilizing the land. The major potential sources of extensive long-term land contamination with radionuclides, in order of decreasing extent, are nuclear war, detonation of a single nuclear weapon (e.g., a terrorist act), serious reactor accidents, and nonfission nuclear weapons accidents that disperse the nuclear fuels (termed ''broken arrows'').

Recent advances in the source term area within the SARNET European severe accident research network

International Nuclear Information System (INIS)

Herranz, L.E.; Haste, T.; Kärkelä, T.

2015-01-01

Highlights: • Main achievements of source term research in SARNET are given. • Emphasis on the radiologically important iodine and ruthenium fission products. • Conclusions on FP release, transport in the RCS and containment behaviour. • Significance of large-scale integral experiments to validate the analyses used. • A thorough list of the most recent references on source term research results. - Abstract: Source Term has been one of the main research areas addressed within the SARNET network during the 7th EC Framework Programme of EURATOM. The entire source term domain was split into three major areas: oxidising impact on source term, iodine chemistry in the reactor coolant system and containment and data and code assessment. The present paper synthesises the main technical outcome stemming from the SARNET FWP7 project in the area of source term and includes an extensive list of references in which deeper insights on specific issues may be found. Besides, based on the analysis of the current state of the art, an outlook of future source term research is outlined, where major changes in research environment are discussed (i.e., the end of the Phébus FP project; the end of the SARNET projects; and the launch of HORIZON 2020). Most probably research projects will be streamlined towards: release and transport under oxidising conditions, containment chemistry, existing and innovative filtered venting systems and others. These will be in addition to a number of projects that have been completed or are ongoing under different national and international frameworks, like VERDON, CHIP and EPICUR started under the International Source Term Programme (ISTP), the OECD/CSNI programmes BIP, BIP2, STEM, THAI and THAI2, and the French national programme MIRE. The experimental PASSAM project under the 7th EC Framework programme, focused on source term mitigation systems, is highlighted as a good example of a project addressing potential enhancement of safety systems

Recent advances in the source term area within the SARNET European severe accident research network

Energy Technology Data Exchange (ETDEWEB)

Herranz, L.E., E-mail: luisen.herranz@ciemat.es [Centro de Investigaciones Energeticas Medio Ambientales y Tecnologica, CIEMAT, Avda. Complutense 40, E-28040 Madrid (Spain); Haste, T. [Institut de Radioprotection et de Sûreté Nucléaire, IRSN, BP 3, F-13115 St Paul lez Durance Cedex (France); Kärkelä, T. [VTT Technical Research Centre of Finland, P.O. Box 1000, FI-02044 VTT Espoo (Finland)

2015-07-15

Highlights: • Main achievements of source term research in SARNET are given. • Emphasis on the radiologically important iodine and ruthenium fission products. • Conclusions on FP release, transport in the RCS and containment behaviour. • Significance of large-scale integral experiments to validate the analyses used. • A thorough list of the most recent references on source term research results. - Abstract: Source Term has been one of the main research areas addressed within the SARNET network during the 7th EC Framework Programme of EURATOM. The entire source term domain was split into three major areas: oxidising impact on source term, iodine chemistry in the reactor coolant system and containment and data and code assessment. The present paper synthesises the main technical outcome stemming from the SARNET FWP7 project in the area of source term and includes an extensive list of references in which deeper insights on specific issues may be found. Besides, based on the analysis of the current state of the art, an outlook of future source term research is outlined, where major changes in research environment are discussed (i.e., the end of the Phébus FP project; the end of the SARNET projects; and the launch of HORIZON 2020). Most probably research projects will be streamlined towards: release and transport under oxidising conditions, containment chemistry, existing and innovative filtered venting systems and others. These will be in addition to a number of projects that have been completed or are ongoing under different national and international frameworks, like VERDON, CHIP and EPICUR started under the International Source Term Programme (ISTP), the OECD/CSNI programmes BIP, BIP2, STEM, THAI and THAI2, and the French national programme MIRE. The experimental PASSAM project under the 7th EC Framework programme, focused on source term mitigation systems, is highlighted as a good example of a project addressing potential enhancement of safety systems

Estimation of Source terms for Emergency Planning and Preparedness

Energy Technology Data Exchange (ETDEWEB)

Yi, Chul Un; Chung, Bag Soon; Ahn, Jae Hyun; Yoon, Duk Ho; Jeong, Chul Young; Lim, Jong Dae [Korea Electric Power Research Institute, Taejon (Korea, Republic of); Kang, Sun Gu; Suk, Ho; Park, Sung Kyu; Lim, Hac Kyu; Lee, Kwang Nam [Korea Power Engineering Company Consulting and Architecture Engineers, (Korea, Republic of)

1997-12-31

In this study the severe accident sequences for each plant of concern, which represent accident sequences with a high core damage frequency and significant accident consequences, were selected based on the results of probabilistic safety assessments and source term and time-histories of various safety parameters under severe accidents. Accidents progression analysis for each selected accident sequence was performed by MAAP code. It was determined that the measured values, dose rate and radioisotope concentration, could provide information to the operators on occurrence and timing of core damage, reactor vessel failure, and containment failure during severe accidents. Radioactive concentration in the containment atmosphere, which may be measured by PASS, was estimated. Radioisotope concentration in emergency planning, evaluation of source term behavior in the containment, estimation of core damage degree, analysis of severe accident phenomena, core damage timing, and the amount of radioisotope released to the environment. (author). 50 refs., 60 figs.

Added Value of uncertainty Estimates of SOurce term and Meteorology (AVESOME)

DEFF Research Database (Denmark)

Sørensen, Jens Havskov; Schönfeldt, Fredrik; Sigg, Robert

In the early phase of a nuclear accident, two large sources of uncertainty exist: one related to the source term and one associated with the meteorological data. Operational methods are being developed in AVESOME for quantitative estimation of uncertainties in atmospheric dispersion prediction.......g. at national meteorological services, the proposed methodology is feasible for real-time use, thereby adding value to decision support. In the recent NKS-B projects MUD, FAUNA and MESO, the implications of meteorological uncertainties for nuclear emergency preparedness and management have been studied...... uncertainty in atmospheric dispersion model forecasting stemming from both the source term and the meteorological data is examined. Ways to implement the uncertainties of forecasting in DSSs, and the impacts on real-time emergency management are described. The proposed methodology allows for efficient real...

Documentation for grants equal to tax model: Volume 3, Source code

International Nuclear Information System (INIS)

Boryczka, M.K.

1986-01-01

The GETT model is capable of forecasting the amount of tax liability associated with all property owned and all activities undertaken by the US Department of Energy (DOE) in site characterization and repository development. The GETT program is a user-friendly, menu-driven model developed using dBASE III/trademark/, a relational data base management system. The data base for GETT consists primarily of eight separate dBASE III/trademark/ files corresponding to each of the eight taxes (real property, personal property, corporate income, franchise, sales, use, severance, and excise) levied by State and local jurisdictions on business property and activity. Additional smaller files help to control model inputs and reporting options. Volume 3 of the GETT model documentation is the source code. The code is arranged primarily by the eight tax types. Other code files include those for JURISDICTION, SIMULATION, VALIDATION, TAXES, CHANGES, REPORTS, GILOT, and GETT. The code has been verified through hand calculations

Regulatory document R-104, Regulatory objectives, requirements and guidelines for the disposal of radioactive wastes - long-term aspects

International Nuclear Information System (INIS)

1987-01-01

The purpose and scope of this document is to present the regulatory basis for judging the long-term acceptability of radioactive waste disposal options. The basic objectives of radioactive waste disposal are given as are the regulatory requirements to be satisfied. (NEA)

Personalized Metaheuristic Clustering Onto Web Documents

Institute of Scientific and Technical Information of China (English)

Wookey Lee

2004-01-01

Optimal clustering for the web documents is known to complicated cornbinatorial Optimization problem and it is hard to develop a generally applicable oplimal algorithm. An accelerated simuIated arlneaIing aIgorithm is developed for automatic web document classification. The web document classification problem is addressed as the problem of best describing a match between a web query and a hypothesized web object. The normalized term frequency and inverse document frequency coefficient is used as a measure of the match. Test beds are generated on - line during the search by transforming model web sites. As a result, web sites can be clustered optimally in terms of keyword vectofs of corresponding web documents.

Coarse Grid Modeling of Turbine Film Cooling Flows Using Volumetric Source Terms

Science.gov (United States)

Heidmann, James D.; Hunter, Scott D.

2001-01-01

The recent trend in numerical modeling of turbine film cooling flows has been toward higher fidelity grids and more complex geometries. This trend has been enabled by the rapid increase in computing power available to researchers. However, the turbine design community requires fast turnaround time in its design computations, rendering these comprehensive simulations ineffective in the design cycle. The present study describes a methodology for implementing a volumetric source term distribution in a coarse grid calculation that can model the small-scale and three-dimensional effects present in turbine film cooling flows. This model could be implemented in turbine design codes or in multistage turbomachinery codes such as APNASA, where the computational grid size may be larger than the film hole size. Detailed computations of a single row of 35 deg round holes on a flat plate have been obtained for blowing ratios of 0.5, 0.8, and 1.0, and density ratios of 1.0 and 2.0 using a multiblock grid system to resolve the flows on both sides of the plate as well as inside the hole itself. These detailed flow fields were spatially averaged to generate a field of volumetric source terms for each conservative flow variable. Solutions were also obtained using three coarse grids having streamwise and spanwise grid spacings of 3d, 1d, and d/3. These coarse grid solutions used the integrated hole exit mass, momentum, energy, and turbulence quantities from the detailed solutions as volumetric source terms. It is shown that a uniform source term addition over a distance from the wall on the order of the hole diameter is able to predict adiabatic film effectiveness better than a near-wall source term model, while strictly enforcing correct values of integrated boundary layer quantities.

The Fukushima releases: an inverse modelling approach to assess the source term by using gamma dose rate observations

Science.gov (United States)

Saunier, Olivier; Mathieu, Anne; Didier, Damien; Tombette, Marilyne; Quélo, Denis; Winiarek, Victor; Bocquet, Marc

2013-04-01

The Chernobyl nuclear accident and more recently the Fukushima accident highlighted that the largest source of error on consequences assessment is the source term estimation including the time evolution of the release rate and its distribution between radioisotopes. Inverse modelling methods have proved to be efficient to assess the source term due to accidental situation (Gudiksen, 1989, Krysta and Bocquet, 2007, Stohl et al 2011, Winiarek et al 2012). These methods combine environmental measurements and atmospheric dispersion models. They have been recently applied to the Fukushima accident. Most existing approaches are designed to use air sampling measurements (Winiarek et al, 2012) and some of them use also deposition measurements (Stohl et al, 2012, Winiarek et al, 2013). During the Fukushima accident, such measurements are far less numerous and not as well distributed within Japan than the dose rate measurements. To efficiently document the evolution of the contamination, gamma dose rate measurements were numerous, well distributed within Japan and they offered a high temporal frequency. However, dose rate data are not as easy to use as air sampling measurements and until now they were not used in inverse modelling approach. Indeed, dose rate data results from all the gamma emitters present in the ground and in the atmosphere in the vicinity of the receptor. They do not allow one to determine the isotopic composition or to distinguish the plume contribution from wet deposition. The presented approach proposes a way to use dose rate measurement in inverse modeling approach without the need of a-priori information on emissions. The method proved to be efficient and reliable when applied on the Fukushima accident. The emissions for the 8 main isotopes Xe-133, Cs-134, Cs-136, Cs-137, Ba-137m, I-131, I-132 and Te-132 have been assessed. The Daiichi power plant events (such as ventings, explosions…) known to have caused atmospheric releases are well identified in

Analysis of accident sequences and source terms at treatment and storage facilities for waste generated by US Department of Energy waste management operations

Energy Technology Data Exchange (ETDEWEB)

Mueller, C.; Nabelssi, B.; Roglans-Ribas, J.; Folga, S.; Policastro, A.; Freeman, W.; Jackson, R.; Mishima, J.; Turner, S.

1996-12-01

This report documents the methodology, computational framework, and results of facility accident analyses performed for the US Department of Energy (DOE) Waste Management Programmatic Environmental Impact Statement (WM PEIS). The accident sequences potentially important to human health risk are specified, their frequencies assessed, and the resultant radiological and chemical source terms evaluated. A personal-computer-based computational framework and database have been developed that provide these results as input to the WM PEIS for the calculation of human health risk impacts. The WM PEIS addresses management of five waste streams in the DOE complex: low-level waste (LLW), hazardous waste (HW), high-level waste (HLW), low-level mixed waste (LLMW), and transuranic waste (TRUW). Currently projected waste generation rates, storage inventories, and treatment process throughputs have been calculated for each of the waste streams. This report summarizes the accident analyses and aggregates the key results for each of the waste streams. Source terms are estimated, and results are presented for each of the major DOE sites and facilities by WM PEIS alternative for each waste stream. Key assumptions in the development of the source terms are identified. The appendices identify the potential atmospheric release of each toxic chemical or radionuclide for each accident scenario studied. They also discuss specific accident analysis data and guidance used or consulted in this report.

NRC source term assessment for incident response dose projections

International Nuclear Information System (INIS)

Easley, P.; Pasedag, W.

1984-01-01

The NRC provides advice and assistance to licensees and State and local authorities in responding to accidents. The TACT code supports this function by providing source term projections for two situations during early (15 to 60 minutes) accident response: (1) Core/containment damage is indicated, but there are no measured releases. Quantification of a predicted release permits emergency response before people are exposed. With TACT, response personnel can estimate releases based on fuel and cladding conditions, coolant boundary and containment integrity, and mitigative systems operability. For this type of estimate, TACT is intermediate between default assumptions and time-consuming mechanistic codes. (2) A combination of plant status and limited release data are available. For this situation, iterations between predictions based on known conditions which are compared to measured releases gives reasonable confidence in supplemental source term information otherwise unavailable: nuclide mix, releases not monitored, and trending or abrupt changes. The assumptions and models used in TACT, and examples of its use, are given in this paper

Selected source term topics. Report to CSNI by an OECD/NEA Group of experts

International Nuclear Information System (INIS)

1987-04-01

CSNI Report 136 summarizes the results of the work performed by the Group of Experts on the Source Term and Environmental Consequences (PWG4) during the period extending from 1983 and 1986. This report is complementary to Part 1, 'Technical Status of the Source Term' of CSNI Report 135, 'Report to CSNI on Source Term Assessment, Containment atmosphere control systems, and accident consequences'; it considers in detail a number of very specific issues thought to be important in the source term area. It consists of: an executive summary (prepared by the Chairman of the Group), a section on conclusions and recommendations, and five technical chapters (fission product chemistry in the primary circuit of a LWR during severe accidents; resuspension/re-entrainment of aerosols in LWRs following a meltdown accident; iodine chemistry under severe accident conditions; effects of combustion, steam explosions and pressurized melt ejection on fission product behaviour; radionuclide removal by pool scrubbing), a technical annex and two appendices

Development of the methodology for application of revised source term to operating nuclear power plants in Korea

International Nuclear Information System (INIS)

Kang, M.S.; Kang, P.; Kang, C.S.; Moon, J.H.

2004-01-01

Considering the current trend in applying the revised source term proposed by NUREG-1465 to the nuclear power plants in the U.S., it is expected that the revised source term will be applied to the Korean operating nuclear power plants in the near future, even though the exact time can not be estimated. To meet the future technical demands, it is necessary to prepare the technical system including the related regulatory requirements in advance. In this research, therefore, it is intended to develop the methodology to apply the revised source term to operating nuclear power plants in Korea. Several principles were established to develop the application methodologies. First, it is not necessary to modify the existing regulations about source term (i.e., any back-fitting to operating nuclear plants is not necessary). Second, if the pertinent margin of safety is guaranteed, the revised source term suggested by NUREG-1465 may be useful to full application. Finally, a part of revised source term could be selected to application based on the technical feasibility. As the results of this research, several methodologies to apply the revised source term to the Korean operating nuclear power plants have been developed, which include: 1) the selective (or limited) application to use only some of all the characteristics of the revised source term, such as release timing of fission products and chemical form of radio-iodine and 2) the full application to use all the characteristics of the revised source term. The developed methodologies are actually applied to Ulchin 9 and 4 units and their application feasibilities are reviewed. The results of this research are used as either a manual in establishing the plan and the procedure for applying the revised source term to the domestic nuclear plant from the utility's viewpoint; or a technical basis of revising the related regulations from the regulatory body's viewpoint. The application of revised source term to operating nuclear

Regulatory Technology Development Plan - Sodium Fast Reactor: Mechanistic Source Term – Trial Calculation

Energy Technology Data Exchange (ETDEWEB)

Grabaskas, David [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Bucknor, Matthew [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Jerden, James [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Brunett, Acacia J. [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Denman, Matthew [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Nuclear Engineering Division; Clark, Andrew [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Nuclear Engineering Division; Denning, Richard S. [Consultant, Columbus, OH (United States)

2016-10-01

The potential release of radioactive material during a plant incident, referred to as the source term, is a vital design metric and will be a major focus of advanced reactor licensing. The U.S. Nuclear Regulatory Commission has stated an expectation for advanced reactor vendors to present a mechanistic assessment of the potential source term in their license applications. The mechanistic source term presents an opportunity for vendors to realistically assess the radiological consequences of an incident, and may allow reduced emergency planning zones and smaller plant sites. However, the development of a mechanistic source term for advanced reactors is not without challenges, as there are often numerous phenomena impacting the transportation and retention of radionuclides. This project sought to evaluate U.S. capabilities regarding the mechanistic assessment of radionuclide release from core damage incidents at metal fueled, pool-type sodium fast reactors (SFRs). The purpose of the analysis was to identify, and prioritize, any gaps regarding computational tools or data necessary for the modeling of radionuclide transport and retention phenomena. To accomplish this task, a parallel-path analysis approach was utilized. One path, led by Argonne and Sandia National Laboratories, sought to perform a mechanistic source term assessment using available codes, data, and models, with the goal to identify gaps in the current knowledge base. The second path, performed by an independent contractor, performed sensitivity analyses to determine the importance of particular radionuclides and transport phenomena in regards to offsite consequences. The results of the two pathways were combined to prioritize gaps in current capabilities.

Source-term model for the SYVAC3-NSURE performance assessment code

International Nuclear Information System (INIS)

Rowat, J.H.; Rattan, D.S.; Dolinar, G.M.

1996-11-01

Radionuclide contaminants in wastes emplaced in disposal facilities will not remain in those facilities indefinitely. Engineered barriers will eventually degrade, allowing radioactivity to escape from the vault. The radionuclide release rate from a low-level radioactive waste (LLRW) disposal facility, the source term, is a key component in the performance assessment of the disposal system. This report describes the source-term model that has been implemented in Ver. 1.03 of the SYVAC3-NSURE (Systems Variability Analysis Code generation 3-Near Surface Repository) code. NSURE is a performance assessment code that evaluates the impact of near-surface disposal of LLRW through the groundwater pathway. The source-term model described here was developed for the Intrusion Resistant Underground Structure (IRUS) disposal facility, which is a vault that is to be located in the unsaturated overburden at AECL's Chalk River Laboratories. The processes included in the vault model are roof and waste package performance, and diffusion, advection and sorption of radionuclides in the vault backfill. The model presented here was developed for the IRUS vault; however, it is applicable to other near-surface disposal facilities. (author). 40 refs., 6 figs

Considerations about source term now used aiming to emergency planning

International Nuclear Information System (INIS)

Austregesilo Filho, H.

1987-01-01

The applicability of source terms, in parametric studies for improving external emergengy plan for Angra-I reactor is presented. The source term is defined as, the quantity and radioactive material disposable for releasing to the environment in case of austere accident in a nuclear power plant. The following hypothesis: occuring accident, 100% of the noble gases, 50% of halogens and 1% of solid fission products contained into the reactor core, are released immediately toward the containment building; the radioactivity releasing to the environment is done at a constant rate of 0.1% in mass per day; the actuation of mitigated systems of radioactivity releasing, such as, spray of container or system of air recirculation by filters, is not considered; and the releasing is done at soil level. (M.C.K.) [pt

New Challenges of the Documentation in Media

Directory of Open Access Journals (Sweden)

Antonio García Jiménez

2015-07-01

Full Text Available This special issue, presented by index.comunicación, is focused on media related information & documentation. This field undergoes constant and profound changes, especially visible in documentation processes. A situation characterized by the existence of tablets, smartphones, applications, and by the almost achieved digitization of traditional documents, in addition to the crisis of the press business model, that involves mutations in the journalists’ tasks and in the relationship between them and Documentation. Papers included in this special issue focus on some of the concerns in this domain: the progressive autonomy of the journalist in access to information sources, the role of press offices as documentation sources, the search of information on the web, the situation of media blogs, the viability of elements of information architecture in smart TV and the development of social TV and its connection to Documentation.

A note on variational multiscale methods for high-contrast heterogeneous porous media flows with rough source terms

KAUST Repository

Calo, Victor M.

2011-09-01

In this short note, we discuss variational multiscale methods for solving porous media flows in high-contrast heterogeneous media with rough source terms. Our objective is to separate, as much as possible, subgrid effects induced by the media properties from those due to heterogeneous source terms. For this reason, enriched coarse spaces designed for high-contrast multiscale problems are used to represent the effects of heterogeneities of the media. Furthermore, rough source terms are captured via auxiliary correction equations that appear in the formulation of variational multiscale methods [23]. These auxiliary equations are localized and one can use additive or multiplicative constructions for the subgrid corrections as discussed in the current paper. Our preliminary numerical results show that one can capture the effects due to both spatial heterogeneities in the coefficients (such as permeability field) and source terms (e.g., due to singular well terms) in one iteration. We test the cases for both smooth source terms and rough source terms and show that with the multiplicative correction, the numerical approximations are more accurate compared to the additive correction. © 2010 Elsevier Ltd.

Software requirements specification document for the AREST code development

International Nuclear Information System (INIS)

Engel, D.W.; McGrail, B.P.; Whitney, P.D.; Gray, W.J.; Williford, R.E.; White, M.D.; Eslinger, P.W.; Altenhofen, M.K.

1993-11-01

The Analysis of the Repository Source Term (AREST) computer code was selected in 1992 by the U.S. Department of Energy. The AREST code will be used to analyze the performance of an underground high level nuclear waste repository. The AREST code is being modified by the Pacific Northwest Laboratory (PNL) in order to evaluate the engineered barrier and waste package designs, model regulatory compliance, analyze sensitivities, and support total systems performance assessment modeling. The current version of the AREST code was developed to be a very useful tool for analyzing model uncertainties and sensitivities to input parameters. The code has also been used successfully in supplying source-terms that were used in a total systems performance assessment. The current version, however, has been found to be inadequate for the comparison and selection of a design for the waste package. This is due to the assumptions and simplifications made in the selection of the process and system models. Thus, the new version of the AREST code will be designed to focus on the details of the individual processes and implementation of more realistic models. This document describes the requirements of the new models that will be implemented. Included in this document is a section describing the near-field environmental conditions for this waste package modeling, description of the new process models that will be implemented, and a description of the computer requirements for the new version of the AREST code

Centrifugal Filtration System for Severe Accident Source Term Treatment

Energy Technology Data Exchange (ETDEWEB)

Liu, Shu Chang; Yim, Man Sung [KAIST, Daejeon (Korea, Republic of)

2016-05-15

The objective of this paper is to present the conceptual design of a filtration system that can be used to process airborne severe accident source term. Reactor containment may lose its structural integrity due to over-pressurization during a severe accident. This can lead to uncontrolled radioactive releases to the environment. For preventing the dispersion of these uncontrolled radioactive releases to the environment, several ways to capture or mitigate these radioactive source term releases are under investigation at KAIST. Such technologies are based on concepts like a vortex-like air curtain, a chemical spray, and a suction arm. Treatment of the radioactive material captured by these systems would be required, before releasing to environment. For current filtration systems in the nuclear industry, IAEA lists sand, multi-venturi scrubber, high efficiency particulate arresting (HEPA), charcoal and combinations of the above in NS-G-1-10, 4.143. Most if not all of the requirements of the scenario for applying this technology near the containment of an NPP site and the environmental constraints were analyzed for use in the design of the centrifuge filtration system.

Assessment on health and energy sources

International Nuclear Information System (INIS)

Acket, C.; Yvon, M.

2013-01-01

After having recalled some issues related to the prevention of environmental health risks and mentioned in the preparation of the debate on energy transition in France, this document gathers actual objective elements for an assessment of health impact of the different energy sources. It discusses the impacts on health (mortality, sicknesses and diseases) of fossil fuels (coal and its wastes, gas), of renewable energies, of nuclear energy. For this last one, the document outlines the lack of documentation for various topics, discusses some results published on the dose impact of nuclear operation, and comment the issue of waste storage. It also recalls the main accidents (Three Mile Island, Chernobyl, and Fukushima) and some of the known and assessed impacts. The third part proposes comparisons between the different energy sources in terms of deadly accidents, of pollution and greenhouse effect (current and late mortality), of released radioactivity (release sources and collective dose). In conclusion, the authors outline that the impact on health of environmental risks must be one of the essential issues for the definition of energy policy, and discuss the resulting implications. Various data are provided in appendix: energy in France and in the world, origins of radioactivity

Using 137Cs and 210Pbex and other sediment source fingerprints to document suspended sediment sources in small forested catchments in south-central Chile

International Nuclear Information System (INIS)

Schuller, P.; Walling, D.E.; Iroumé, A.; Quilodrán, C.; Castillo, A.; Navas, A.

2013-01-01

A study of the impact of forest harvesting operations on sediment mobilization from forested catchments has been undertaken in south-central Chile. The study focused on two sets of small paired catchments (treatment and control), with similar soil type, but contrasting mean annual rainfall, located about 400 km apart at Nacimiento (1200 mm yr −1 ) and Los Ulmos (2500 mm yr −1 ). The objective was to study the changes in the relative contribution of the primary sources of fine sediment caused by forestry operations. Attention focused on the pre-harvest and post-harvest periods and the post-replanting period was included for the Nacimiento treatment catchment. The sediment source fingerprinting technique was used to document the contributions of the potential sources. Emphasis was placed on discriminating between the forest slopes, forest roads and channel erosion as potential sources of fine sediment and on assessing the relative contributions of these three sources to the sediment yield from the catchments. The fallout radionuclides (FRNs) 137 Cs and excess lead-210, the environmental radionuclides 226 Ra and 40 K and soil organic matter (SOM) were tested as possible fingerprints for discriminating between potential sediment sources. The Kruskal–Wallis test and discriminant function analysis were used to guide the selection of the optimum fingerprint set for each catchment and observation period. Either one or both of the FRNs were selected for inclusion in the optimum fingerprint for all datasets. The relative contribution of each sediment source to the target sediment load was estimated using the selected fingerprint properties, and a mixing model coupled with a Monte Carlo simulation technique that takes account of uncertainty in characterizing sediment source properties. The goodness of fit of the mixing model was tested by comparing the measured and simulated fingerprint properties for the target sediment samples. In the Nacimiento treatment catchment

Experimental determination of chosen document elements parameters from raster graphics sources

Directory of Open Access Journals (Sweden)

Jiří Rybička

2010-01-01

Full Text Available Visual appearance of documents and their formal quality is considered to be as important as the content quality. Formal and typographical quality of documents can be evaluated by an automated system that processes raster images of documents. A document is described by a formal model that treats a page as an object and also as a set of elements, whereas page elements include text and graphic object. All elements are described by their parameters depending on elements’ type. For future evaluation, mainly text objects are important. This paper describes the experimental determination of chosen document elements parameters from raster images. Techniques for image processing are used, where an image is represented as a matrix of dots and parameter values are extracted. Algorithms for parameter extraction from raster images were designed and were aimed mainly at typographical parameters like indentation, alignment, font size or spacing. Algorithms were tested on a set of 100 images of paragraphs or pages and provide very good results. Extracted parameters can be directly used for typographical quality evaluation.

Advanced Reactor PSA Methodologies for System Reliability Analysis and Source Term Assessment

Energy Technology Data Exchange (ETDEWEB)

Grabaskas, D.; Brunett, A.; Passerini, S.; Grelle, A.; Bucknor, M.

2017-06-26

Beginning in 2015, a project was initiated to update and modernize the probabilistic safety assessment (PSA) of the GE-Hitachi PRISM sodium fast reactor. This project is a collaboration between GE-Hitachi and Argonne National Laboratory (Argonne), and funded in part by the U.S. Department of Energy. Specifically, the role of Argonne is to assess the reliability of passive safety systems, complete a mechanistic source term calculation, and provide component reliability estimates. The assessment of passive system reliability focused on the performance of the Reactor Vessel Auxiliary Cooling System (RVACS) and the inherent reactivity feedback mechanisms of the metal fuel core. The mechanistic source term assessment attempted to provide a sequence specific source term evaluation to quantify offsite consequences. Lastly, the reliability assessment focused on components specific to the sodium fast reactor, including electromagnetic pumps, intermediate heat exchangers, the steam generator, and sodium valves and piping.

ITER safety task NID-5a: ITER tritium environmental source terms - safety analysis basis

International Nuclear Information System (INIS)

Natalizio, A.; Kalyanam, K.M.

1994-09-01

The Canadian Fusion Fuels Technology Project's (CFFTP) is part of the contribution to ITER task NID-5a, Initial Tritium Source Term. This safety analysis basis constitutes the first part of the work for establishing tritium source terms and is intended to solicit comments and obtain agreement. The analysis objective is to provide an early estimate of tritium environmental source terms for the events to be analyzed. Events that would result in the loss of tritium are: a Loss of Coolant Accident (LOCA), a vacuum vessel boundary breach. a torus exhaust line failure, a fuelling machine process boundary failure, a fuel processing system process boundary failure, a water detritiation system process boundary failure and an isotope separation system process boundary failure. 9 figs

Realistic minimum accident source terms - Evaluation, application, and risk acceptance

International Nuclear Information System (INIS)

Angelo, P. L.

2009-01-01

The evaluation, application, and risk acceptance for realistic minimum accident source terms can represent a complex and arduous undertaking. This effort poses a very high impact to design, construction cost, operations and maintenance, and integrated safety over the expected facility lifetime. At the 2005 Nuclear Criticality Safety Division (NCSD) Meeting in Knoxville Tenn., two papers were presented mat summarized the Y-12 effort that reduced the number of criticality accident alarm system (CAAS) detectors originally designed for the new Highly Enriched Uranium Materials Facility (HEUMF) from 258 to an eventual as-built number of 60. Part of that effort relied on determining a realistic minimum accident source term specific to the facility. Since that time, the rationale for an alternate minimum accident has been strengthened by an evaluation process that incorporates realism. A recent update to the HEUMF CAAS technical basis highlights the concepts presented here. (authors)

A novel integrated approach for the hazardous radioactive dust source terms estimation in future nuclear fusion power plants.

Science.gov (United States)

Poggi, L A; Malizia, A; Ciparisse, J F; Gaudio, P

2016-10-01

An open issue still under investigation by several international entities working on the safety and security field for the foreseen nuclear fusion reactors is the estimation of source terms that are a hazard for the operators and public, and for the machine itself in terms of efficiency and integrity in case of severe accident scenarios. Source term estimation is a crucial key safety issue to be addressed in the future reactors safety assessments, and the estimates available at the time are not sufficiently satisfactory. The lack of neutronic data along with the insufficiently accurate methodologies used until now, calls for an integrated methodology for source term estimation that can provide predictions with an adequate accuracy. This work proposes a complete methodology to estimate dust source terms starting from a broad information gathering. The wide number of parameters that can influence dust source term production is reduced with statistical tools using a combination of screening, sensitivity analysis, and uncertainty analysis. Finally, a preliminary and simplified methodology for dust source term production prediction for future devices is presented.

Market Analysis and Consumer Impacts Source Document. Part II. Review of Motor Vehicle Market and Consumer Expenditures on Motor Vehicle Transportation

Science.gov (United States)

1980-12-01

This source document on motor vehicle market analysis and consumer impacts consists of three parts. Part II consists of studies and review on: motor vehicle sales trends; motor vehicle fleet life and fleet composition; car buying patterns of the busi...

Effects of Deep Water Source-Sink Terms in 3rd generation Wave Model SWAN using different wind data in Black Sea

Science.gov (United States)

Kirezci, Cagil; Ozyurt Tarakcioglu, Gulizar

2016-04-01

coefficient (WAM Cycle 3).The second method follows the quassi linear wind-wave theory by Janssen(1989,1991) which also considers the atmospheric boundary layer effects and the roughness length of the sea surface (WAM Cycle 4).(SWAN Technical Documentation,2015) The dissipation caused by whitecapping depends on the steepness of the waves. There are two different steepness dependent coefficient configurations in SWAN model corresponding to the selected wind-wave interaction formulations which are mentioned above (Komen and Janssen approaches). Lastly ,there are 3 options for defining deep water non-linear wave-wave interaction, which are DIA(Discrete Interaction Approximation)by Hasselman (quadruplets), XNL(which is based on the original six-dimensional Boltzmann integral formulation of Hasselmann), and multiple DIA which considers up to 6 wave number configurations by Hashimoto et al. (2002).(SWAN Technical Documentation,2015) In this study, 540 test cases are modelled using all possible selections of deep water source and sinks approaches available in SWAN model. The computed results are compared with buoy measurements. The uncertainty due to different source sink selections are quantified using different statistical analysis. Preliminary results show that some of the term configurations predict the significant wave height (Hs) less than actual values measured at the buoy locations. One of the reasons of the underestimation of the wave parameters could be the lower wind speed estimated in closed basins and the other one is the uncertainties in the wind-sea interaction. All of the results, comparisons and discussions will highlight the best source sink approach to be used to model extreme wave events in Black Sea. References Kirezci C., Ozyurt G., (2015), "Comparison of Wave Models in Black Sea", UK YCSEC 2015, 21-23 March 2015, Manchester Özhan, E. and Abdalla, S.,(1999)"Wind and Wave Climotology of the Turkish Coast and the Black Sea:An Overview of the NATO TU

Chernobyl source term, atmospheric dispersion, and dose estimation

International Nuclear Information System (INIS)

Gudiksen, P.H.; Harvey, T.F.; Lange, R.

1988-02-01

The Chernobyl source term available for long-range transport was estimated by integration of radiological measurements with atmospheric dispersion modeling, and by reactor core radionuclide inventory estimation in conjunction with WASH-1400 release fractions associated with specific chemical groups. These analyses indicated that essentially all of the noble gases, 80% of the radioiodines, 40% of the radiocesium, 10% of the tellurium, and about 1% or less of the more refractory elements were released. Atmospheric dispersion modeling of the radioactive cloud over the Northern Hemisphere revealed that the cloud became segmented during the first day, with the lower section heading toward Scandinavia and the uppper part heading in a southeasterly direction with subsequent transport across Asia to Japan, the North Pacific, and the west coast of North America. The inhalation doses due to direct cloud exposure were estimated to exceed 10 mGy near the Chernobyl area, to range between 0.1 and 0.001 mGy within most of Europe, and to be generally less than 0.00001 mGy within the US. The Chernobyl source term was several orders of magnitude greater than those associated with the Windscale and TMI reactor accidents, while the 137 Cs from the Chernobyl event is about 6% of that released by the US and USSR atmospheric nuclear weapon tests. 9 refs., 3 figs., 6 tabs

SRS ecology: Environmental information document

Energy Technology Data Exchange (ETDEWEB)

Wike, L.D.; Shipley, R.W.; Bowers, J.A. [and others

1993-09-01

The purpose of this Document is to provide a source of ecological information based on the exiting knowledge gained from research conducted at the Savannah River Site. This document provides a summary and synthesis of ecological research in the three main ecosystem types found at SRS and information on the threatened and endangered species residing there.

SRS ecology: Environmental information document

International Nuclear Information System (INIS)

Wike, L.D.; Shipley, R.W.; Bowers, J.A.

1993-09-01

The purpose of this Document is to provide a source of ecological information based on the exiting knowledge gained from research conducted at the Savannah River Site. This document provides a summary and synthesis of ecological research in the three main ecosystem types found at SRS and information on the threatened and endangered species residing there

Source term identification in atmospheric modelling via sparse optimization

Science.gov (United States)

Adam, Lukas; Branda, Martin; Hamburger, Thomas

2015-04-01

Inverse modelling plays an important role in identifying the amount of harmful substances released into atmosphere during major incidents such as power plant accidents or volcano eruptions. Another possible application of inverse modelling lies in the monitoring the CO2 emission limits where only observations at certain places are available and the task is to estimate the total releases at given locations. This gives rise to minimizing the discrepancy between the observations and the model predictions. There are two standard ways of solving such problems. In the first one, this discrepancy is regularized by adding additional terms. Such terms may include Tikhonov regularization, distance from a priori information or a smoothing term. The resulting, usually quadratic, problem is then solved via standard optimization solvers. The second approach assumes that the error term has a (normal) distribution and makes use of Bayesian modelling to identify the source term. Instead of following the above-mentioned approaches, we utilize techniques from the field of compressive sensing. Such techniques look for a sparsest solution (solution with the smallest number of nonzeros) of a linear system, where a maximal allowed error term may be added to this system. Even though this field is a developed one with many possible solution techniques, most of them do not consider even the simplest constraints which are naturally present in atmospheric modelling. One of such examples is the nonnegativity of release amounts. We believe that the concept of a sparse solution is natural in both problems of identification of the source location and of the time process of the source release. In the first case, it is usually assumed that there are only few release points and the task is to find them. In the second case, the time window is usually much longer than the duration of the actual release. In both cases, the optimal solution should contain a large amount of zeros, giving rise to the

Fission product source terms and engineered safety features

International Nuclear Information System (INIS)

Malinauskas, A.P.

1984-01-01

The author states that new, technically defensible, methodologies to establish realistic source term values for nuclear reactor accidents will soon be available. Although these methodologies will undoubtedly find widespread use in the development of accident response procedures, the author states that it is less clear that the industry is preparing to employ the newer results to develop a more rational approach to strategies for the mitigation of fission product releases. Questions concerning the performance of existing engineered safety systems are reviewed

Supplemental analysis of accident sequences and source terms for waste treatment and storage operations and related facilities for the US Department of Energy waste management programmatic environmental impact statement

International Nuclear Information System (INIS)

Folga, S.; Mueller, C.; Nabelssi, B.; Kohout, E.; Mishima, J.

1996-12-01

This report presents supplemental information for the document Analysis of Accident Sequences and Source Terms at Waste Treatment, Storage, and Disposal Facilities for Waste Generated by US Department of Energy Waste Management Operations. Additional technical support information is supplied concerning treatment of transuranic waste by incineration and considering the Alternative Organic Treatment option for low-level mixed waste. The latest respirable airborne release fraction values published by the US Department of Energy for use in accident analysis have been used and are included as Appendix D, where respirable airborne release fraction is defined as the fraction of material exposed to accident stresses that could become airborne as a result of the accident. A set of dominant waste treatment processes and accident scenarios was selected for a screening-process analysis. A subset of results (release source terms) from this analysis is presented

An integrated information retrieval and document management system

Science.gov (United States)

Coles, L. Stephen; Alvarez, J. Fernando; Chen, James; Chen, William; Cheung, Lai-Mei; Clancy, Susan; Wong, Alexis

1993-01-01

This paper describes the requirements and prototype development for an intelligent document management and information retrieval system that will be capable of handling millions of pages of text or other data. Technologies for scanning, Optical Character Recognition (OCR), magneto-optical storage, and multiplatform retrieval using a Standard Query Language (SQL) will be discussed. The semantic ambiguity inherent in the English language is somewhat compensated-for through the use of coefficients or weighting factors for partial synonyms. Such coefficients are used both for defining structured query trees for routine queries and for establishing long-term interest profiles that can be used on a regular basis to alert individual users to the presence of relevant documents that may have just arrived from an external source, such as a news wire service. Although this attempt at evidential reasoning is limited in comparison with the latest developments in AI Expert Systems technology, it has the advantage of being commercially available.

Use of source term code package in the ELEBRA MX-850 system

International Nuclear Information System (INIS)

Guimaraes, A.C.F.; Goes, A.G.A.

1988-12-01

The implantation of source term code package in the ELEBRA-MX850 system is presented. The source term is formed when radioactive materials generated in nuclear fuel leakage toward containment and the external environment to reactor containment. The implantated version in the ELEBRA system are composed of five codes: MARCH 3, TRAPMELT 3, THCCA, VANESA and NAVA. The original example case was used. The example consists of a small loca accident in a PWR type reactor. A sensitivity study for the TRAPMELT 3 code was carried out, modifying the 'TIME STEP' to estimate the processing time of CPU for executing the original example case. (M.C.K.) [pt

Development of Reference Source Terms for EU-APR1400

Energy Technology Data Exchange (ETDEWEB)

Kim, ByungIl; Lee, Chonghui; Lee, Dongsu; Ko, Heejin; Kang, Sangho [KEPCO Engineering and Construction Co. Inc., Yongin (Korea, Republic of)

2014-05-15

These source terms are developed for the typical U. S. NPP and do not reflect the design characteristics of EU-APR1400 (1,400 MWe PWR) which will be applied for the EUR certification in European countries. The process of developing the RST for EU-APR1400 is to undergo a similar process that NUREG-1465 had gone through when it came out with its proposed source terms. The purpose of this study is to develop the EU-APR1400 design-specific RST complied with the EUR. The Large LOCA is the reference equence used in the NUREG-1465 evaluation, whereas the EUAPR1400 risk-significant sequences are dominated by small LOCA and non-LOCA sequences. Moreover, when considering the EU-APR1400 has many design features to mitigate the consequences of severe accident phenomena, it is not surprising that the aspects of both release fractions and durations are distinctly different from NUREG-1465. This RST will be continuously updated to reflect to the design features of EU-APR1400, and then, be used as the reference for design purposes such as criteria satisfaction of radioactivity releases, equipment survivability, control room habitability for severe accident, and so on.

Semi-implicit and fully implicit shock-capturing methods for hyperbolic conservation laws with stiff source terms

International Nuclear Information System (INIS)

Yee, H.C.; Shinn, J.L.

1986-12-01

Some numerical aspects of finite-difference algorithms for nonlinear multidimensional hyperbolic conservation laws with stiff nonhomogenous (source) terms are discussed. If the stiffness is entirely dominated by the source term, a semi-implicit shock-capturing method is proposed provided that the Jacobian of the source terms possesses certain properties. The proposed semi-implicit method can be viewed as a variant of the Bussing and Murman point-implicit scheme with a more appropriate numerical dissipation for the computation of strong shock waves. However, if the stiffness is not solely dominated by the source terms, a fully implicit method would be a better choice. The situation is complicated by problems that are higher than one dimension, and the presence of stiff source terms further complicates the solution procedures for alternating direction implicit (ADI) methods. Several alternatives are discussed. The primary motivation for constructing these schemes was to address thermally and chemically nonequilibrium flows in the hypersonic regime. Due to the unique structure of the eigenvalues and eigenvectors for fluid flows of this type, the computation can be simplified, thus providing a more efficient solution procedure than one might have anticipated

Semi-implicit and fully implicit shock-capturing methods for hyperbolic conservation laws with stiff source terms

International Nuclear Information System (INIS)

Yee, H.C.; Shinn, J.L.

1987-01-01

Some numerical aspects of finite-difference algorithms for nonlinear multidimensional hyperbolic conservation laws with stiff nonhomogeneous (source) terms are discussed. If the stiffness is entirely dominated by the source term, a semi-implicit shock-capturing method is proposed provided that the Jacobian of the source terms possesses certain properties. The proposed semi-implicit method can be viewed as a variant of the Bussing and Murman point-implicit scheme with a more appropriate numerical dissipation for the computation of strong shock waves. However, if the stiffness is not solely dominated by the source terms, a fully implicit method would be a better choice. The situation is complicated by problems that are higher than one dimension, and the presence of stiff source terms further complicates the solution procedures for alternating direction implicit (ADI) methods. Several alternatives are discussed. The primary motivation for constructing these schemes was to address thermally and chemically nonequilibrium flows in the hypersonic regime. Due to the unique structure of the eigenvalues and eigenvectors for fluid flows of this type, the computation can be simplified, thus providing a more efficient solution procedure than one might have anticipated. 46 references

Evaluation of Long-term Performance of Enhanced Anaerobic Source Zone Bioremediation using mass flux

Science.gov (United States)

Haluska, A.; Cho, J.; Hatzinger, P.; Annable, M. D.

2017-12-01

Chlorinated ethene DNAPL source zones in groundwater act as potential long term sources of contamination as they dissolve yielding concentrations well above MCLs, posing an on-going public health risk. Enhanced bioremediation has been applied to treat many source zones with significant promise, but long-term sustainability of this technology has not been thoroughly assessed. This study evaluated the long-term effectiveness of enhanced anaerobic source zone bioremediation at chloroethene contaminated sites to determine if the treatment prevented contaminant rebound and removed NAPL from the source zone. Long-term performance was evaluated based on achieving MCL-based contaminant mass fluxes in parent compound concentrations during different monitoring periods. Groundwater concertation versus time data was compiled for 6-sites and post-remedial contaminant mass flux data was then measured using passive flux meters at wells both within and down-gradient of the source zone. Post-remedial mass flux data was then combined with pre-remedial water quality data to estimate pre-remedial mass flux. This information was used to characterize a DNAPL dissolution source strength function, such as the Power Law Model and the Equilibrium Stream tube model. The six-sites characterized for this study were (1) Former Charleston Air Force Base, Charleston, SC; (2) Dover Air Force Base, Dover, DE; (3) Treasure Island Naval Station, San Francisco, CA; (4) Former Raritan Arsenal, Edison, NJ; (5) Naval Air Station, Jacksonville, FL; and, (6) Former Naval Air Station, Alameda, CA. Contaminant mass fluxes decreased for all the sites by the end of the post-treatment monitoring period and rebound was limited within the source zone. Post remedial source strength function estimates suggest that decreases in contaminant mass flux will continue to occur at these sites, but a mass flux based on MCL levels may never be exceeded. Thus, site clean-up goals should be evaluated as order

Multimodal document management in radiotherapy

International Nuclear Information System (INIS)

Fahrner, H.; Kirrmann, S.; Roehner, F.; Schmucker, M.; Hall, M.; Heinemann, F.

2013-01-01

Background and purpose: After incorporating treatment planning and the organisational model of treatment planning in the operating schedule system (BAS, 'Betriebsablaufsystem'), complete document qualities were embedded in the digital environment. The aim of this project was to integrate all documents independent of their source (paper-bound or digital) and to make content from the BAS available in a structured manner. As many workflow steps as possible should be automated, e.g. assigning a document to a patient in the BAS. Additionally it must be guaranteed that at all times it could be traced who, when, how and from which source documents were imported into the departmental system. Furthermore work procedures should be changed that the documentation conducted either directly in the departmental system or from external systems can be incorporated digitally and paper document can be completely avoided (e.g. documents such as treatment certificate, treatment plans or documentation). It was a further aim, if possible, to automate the removal of paper documents from the departmental work flow, or even to make such paper documents superfluous. In this way patient letters for follow-up appointments should automatically generated from the BAS. Similarly patient record extracts in the form of PDF files should be enabled, e.g. for controlling purposes. Method: The available document qualities were analysed in detail by a multidisciplinary working group (BAS-AG) and after this examination and assessment of the possibility of modelling in our departmental workflow (BAS) they were transcribed into a flow diagram. The gathered specifications were implemented in a test environment by the clinical and administrative IT group of the department of radiation oncology and subsequent to a detailed analysis introduced into clinical routine. Results: The department has succeeded under the conditions of the aforementioned criteria to embed all relevant documents in the departmental

Analysis of accident sequences and source terms at waste treatment and storage facilities for waste generated by U.S. Department of Energy Waste Management Operations, Volume 3: Appendixes C-H

International Nuclear Information System (INIS)

Mueller, C.; Nabelssi, B.; Roglans-Ribas, J.

1995-04-01

This report contains the Appendices for the Analysis of Accident Sequences and Source Terms at Waste Treatment and Storage Facilities for Waste Generated by the U.S. Department of Energy Waste Management Operations. The main report documents the methodology, computational framework, and results of facility accident analyses performed as a part of the U.S. Department of Energy (DOE) Waste Management Programmatic Environmental Impact Statement (WM PEIS). The accident sequences potentially important to human health risk are specified, their frequencies are assessed, and the resultant radiological and chemical source terms are evaluated. A personal computer-based computational framework and database have been developed that provide these results as input to the WM PEIS for calculation of human health risk impacts. This report summarizes the accident analyses and aggregates the key results for each of the waste streams. Source terms are estimated and results are presented for each of the major DOE sites and facilities by WM PEIS alternative for each waste stream. The appendices identify the potential atmospheric release of each toxic chemical or radionuclide for each accident scenario studied. They also provide discussion of specific accident analysis data and guidance used or consulted in this report

Analysis of accident sequences and source terms at waste treatment and storage facilities for waste generated by U.S. Department of Energy Waste Management Operations, Volume 3: Appendixes C-H

Energy Technology Data Exchange (ETDEWEB)

Mueller, C.; Nabelssi, B.; Roglans-Ribas, J. [and others

1995-04-01

This report contains the Appendices for the Analysis of Accident Sequences and Source Terms at Waste Treatment and Storage Facilities for Waste Generated by the U.S. Department of Energy Waste Management Operations. The main report documents the methodology, computational framework, and results of facility accident analyses performed as a part of the U.S. Department of Energy (DOE) Waste Management Programmatic Environmental Impact Statement (WM PEIS). The accident sequences potentially important to human health risk are specified, their frequencies are assessed, and the resultant radiological and chemical source terms are evaluated. A personal computer-based computational framework and database have been developed that provide these results as input to the WM PEIS for calculation of human health risk impacts. This report summarizes the accident analyses and aggregates the key results for each of the waste streams. Source terms are estimated and results are presented for each of the major DOE sites and facilities by WM PEIS alternative for each waste stream. The appendices identify the potential atmospheric release of each toxic chemical or radionuclide for each accident scenario studied. They also provide discussion of specific accident analysis data and guidance used or consulted in this report.

Inventory and source term evaluation of Russian nuclear power plants for marine applications

International Nuclear Information System (INIS)

Reistad, O.; Oelgaard, P.L.

2006-04-01

This report discusses inventory and source term properties in regard to operation and possible releases due to accidents from Russian marine reactor systems. The first part of the report discusses relevant accidents on the basis of both Russian and western sources. The overview shows that certain vessels were much more accident prone compared to others, in addition, there have been a noteworthy reduction in accidents the last two decades. However, during the last years new types of incidents, such as collisions, has occurred more frequently. The second part of the study considers in detail the most important factors for the source term; reactor operational characteristics and the radionuclide inventory. While Russian icebreakers has been operated on a similar basis as commercial power plants, the submarines has different power cyclograms which results in considerable lower values for fission product inventory. Theoretical values for radionuclide inventory are compared with computed results using the modelling tool HELIOS. Regarding inventory of transuranic elements, the results of the calculations are discussed in detail for selected vessels. Criticality accidents, loss-of-cooling accidents and sinking accidents are considered, bases on actual experiences with these types of accident and on theoretical considerations, and source terms for these accidents are discussed in the last chapter. (au)

Inventory and source term evaluation of Russian nuclear power plants for marine applications

Energy Technology Data Exchange (ETDEWEB)

Reistad, O. [Norwegian Radiation Protection Authority (Norway); Oelgaard, P.L. [Risoe National Lab. (Denmark)

2006-04-15

This report discusses inventory and source term properties in regard to operation and possible releases due to accidents from Russian marine reactor systems. The first part of the report discusses relevant accidents on the basis of both Russian and western sources. The overview shows that certain vessels were much more accident prone compared to others, in addition, there have been a noteworthy reduction in accidents the last two decades. However, during the last years new types of incidents, such as collisions, has occurred more frequently. The second part of the study considers in detail the most important factors for the source term; reactor operational characteristics and the radionuclide inventory. While Russian icebreakers has been operated on a similar basis as commercial power plants, the submarines has different power cyclograms which results in considerable lower values for fission product inventory. Theoretical values for radionuclide inventory are compared with computed results using the modelling tool HELIOS. Regarding inventory of transuranic elements, the results of the calculations are discussed in detail for selected vessels. Criticality accidents, loss-of-cooling accidents and sinking accidents are considered, bases on actual experiences with these types of accident and on theoretical considerations, and source terms for these accidents are discussed in the last chapter. (au)

High level waste storage tanks 242-A evaporator standards/requirement identification document

International Nuclear Information System (INIS)

Biebesheimer, E.

1996-01-01

This document, the Standards/Requirements Identification Document (S/RIDS) for the subject facility, represents the necessary and sufficient requirements to provide an adequate level of protection of the worker, public health and safety, and the environment. It lists those source documents from which requirements were extracted, and those requirements documents considered, but from which no requirements where taken. Documents considered as source documents included State and Federal Regulations, DOE Orders, and DOE Standards

Source terms for airborne radioactivity arising from uranium mill wastes

International Nuclear Information System (INIS)

O'Riordan, M.C.; Downing, A.L.

1978-01-01

One of the problems in assessing the radiological impact of uranium milling is to determine the rates of release to the air of material from the various sources of radioactivity. Such source terms are required for modelling the transport of radioactive material in the atmosphere. Activity arises from various point and area sources in the mill itself and from the mill tailings. The state of the tailings changes in time from slurry to solid. A layer of water may be maintained over the solids during the life of the mine, and the tailings may be covered with inert material on abandonment. Releases may be both gaseous and particulate. This paper indicates ways in which radon emanation and the suspension of long-lived particulate activity might be quantified, and areas requiring further exploration are identified

Documenting open source migration processes for re-use

CSIR Research Space (South Africa)

Gerber, A

2010-10-01

Full Text Available There are several sources that indicate a remarkable increase in the adoption of open source software (OSS) into the technology infrastructure of organizations. In fact, the number of medium to large organizations without some OSS installations...

Documents on Disarmament.

Science.gov (United States)

Arms Control and Disarmament Agency, Washington, DC.

This publication, latest in a series of volumes issued annually since 1960, contains primary source documents on arms control and disarmament developments during 1969. The main chronological arrangement is supplemented by both chronological and topical lists of contents. Other reference aids include a subject/author index, and lists of…

Unsplit schemes for hyperbolic conservation laws with source terms in one space dimension

International Nuclear Information System (INIS)

Papalexandris, M.V.; Leonard, A.; Dimotakis, P.E.

1997-01-01

The present work is concerned with an application of the theory of characteristics to conservation laws with source terms in one space dimension, such as the Euler equations for reacting flows. Space-time paths are introduced on which the flow/chemistry equations decouple to a characteristic set of ODE's for the corresponding homogeneous laws, thus allowing the introduction of functions analogous to the Riemann invariants in classical theory. The geometry of these paths depends on the spatial gradients of the solution. This particular decomposition can be used in the design of efficient unsplit algorithms for the numerical integration of the equations. As a first step, these ideas are implemented for the case of a scalar conservation law with a nonlinear source term. The resulting algorithm belongs to the class of MUSCL-type, shock-capturing schemes. Its accuracy and robustness are checked through a series of tests. The stiffness of the source term is also studied. Then, the algorithm is generalized for a system of hyperbolic equations, namely the Euler equations for reacting flows. A numerical study of unstable detonations is performed. 57 refs

Student-Centered Pedagogy and Real-World Research: Using Documents as Sources of Data in Teaching Social Science Skills and Methods

Science.gov (United States)

Peyrefitte, Magali; Lazar, Gillian

2018-01-01

This teaching note describes the design and implementation of an activity in a 90-minute teaching session that was developed to introduce a diverse cohort of first-year criminology and sociology students to the use of documents as sources of data. This approach was contextualized in real-world research through scaffolded, student-centered tasks…

Challenges in defining a radiologic and hydrologic source term for underground nuclear test centers, Nevada Test Site, Nye County, Nevada

International Nuclear Information System (INIS)

Smith, D.K.

1995-06-01

The compilation of a radionuclide inventory for long-lived radioactive contaminants residual from nuclear testing provides a partial measure of the radiologic source term at the Nevada Test Site. The radiologic source term also includes potentially mobile short-lived radionuclides excluded from the inventory. The radiologic source term for tritium is known with accuracy and is equivalent to the hydrologic source term within the saturated zone. Definition of the total hydrologic source term for fission and activation products that have high activities for decades following underground testing involves knowledge and assumptions which are presently unavailable. Systematic investigation of the behavior of fission products, activation products and actinides under saturated or Partially saturated conditions is imperative to define a representative total hydrologic source term. This is particularly important given the heterogeneous distribution of radionuclides within testing centers. Data quality objectives which emphasize a combination of measurements and credible estimates of the hydrologic source term are a priority for near-field investigations at the Nevada Test Site

Least-squares finite-element method for shallow-water equations with source terms

Institute of Scientific and Technical Information of China (English)

Shin-Jye Liang; Tai-Wen Hsu

2009-01-01

Numerical solution of shallow-water equations (SWE) has been a challenging task because of its nonlinear hyperbolic nature, admitting discontinuous solution, and the need to satisfy the C-property. The presence of source terms in momentum equations, such as the bottom slope and friction of bed, compounds the difficulties further. In this paper, a least-squares finite-element method for the space discretization and θ-method for the time integration is developed for the 2D non-conservative SWE including the source terms. Advantages of the method include: the source terms can be approximated easily with interpolation functions, no upwind scheme is needed, as well as the resulting system equations is symmetric and positive-definite, therefore, can be solved efficiently with the conjugate gradient method. The method is applied to steady and unsteady flows, subcritical and transcritical flow over a bump, 1D and 2D circular dam-break, wave past a circular cylinder, as well as wave past a hump. Computed results show good C-property, conservation property and compare well with exact solutions and other numerical results for flows with weak and mild gradient changes, but lead to inaccurate predictions for flows with strong gradient changes and discontinuities.

Inverse kinetics method with source term for subcriticality measurements during criticality approach in the IPEN/MB-01 research reactor

International Nuclear Information System (INIS)

Loureiro, Cesar Augusto Domingues; Santos, Adimir dos

2009-01-01

In reactor physics tests which are performed at the startup after refueling the commercial PWRs, it is important to monitor subcriticality continuously during criticality approach. Reactivity measurements by the inverse kinetics method are widely used during the operation of a nuclear reactor and it is possible to perform an online reactivity measurement based on the point reactor kinetics equations. This technique is successful applied at sufficiently high power level or to a core without an external neutron source where the neutron source term in point reactor kinetics equations may be neglected. For operation at low power levels, the contribution of the neutron source must be taken into account and this implies the knowledge of a quantity proportional to the source strength, and then it should be determined. Some experiments have been performed in the IPEN/MB-01 Research Reactor for the determination of the Source Term, using the Least Square Inverse Kinetics Method (LSIKM). A digital reactivity meter which neglects the source term is used to calculate the reactivity and then the source term can be determined by the LSIKM. After determining the source term, its value can be added to the algorithm and the reactivity can be determined again, considering the source term. The new digital reactivity meter can be used now to monitor reactivity during the criticality approach and the measured value for the reactivity is more precise than the meter which neglects the source term. (author)

The MetaLex Document Server : Legal Documents as Versioned Linked Data

NARCIS (Netherlands)

Hoekstra, R.; Aroyo, L.; Welty, C.; Alani, H.; Taylor, J.; Bernstein, A.; Kagal, L.; Noy, N.; Blomqvist, E.

2011-01-01

This paper introduces the MetaLex Document Server (MDS), an ongoing project to improve access to legal sources (regulations, court rulings) by means of a generic legal XML syntax (CEN MetaLex) and Linked Data. The MDS defines a generic conversion mechanism from legacy legal XML syntaxes to CEN

Atucha-I source terms for sequences initiated by transients

International Nuclear Information System (INIS)

Baron, J.; Bastianelli, B.

1997-01-01

The present work is part of an expected source terms study in the Atucha I nuclear power plant during severe accidents. From the accident sequences with a significant probability to produce core damage, those initiated by operational transients have been identified as the most relevant. These sequences have some common characteristics, in the sense that all of them resume in the opening of the primary system safety valves, and leave this path open for the coolant loss. In the case these sequences continue as severe accidents, the same path will be used for the release of the radionuclides, from the core, through the primary system and to the containment. Later in the severe accident sequence, the failure of the pressure vessel will occur, and the corium will fall inside the reactor cavity, interacting with the concrete. During these processes, more radioactive products will be released inside the containment. In the present work the severe accident simulation initiated by a blackout is performed, from the point of view of the phenomenology of the behavior of the radioactive products, as they are transported in the piping, during the core-concrete interactions, and inside the containment buildings until it failure. The final result is the source term into the atmosphere. (author) [es

Regulatory Technology Development Plan Sodium Fast Reactor. Mechanistic Source Term Development

Energy Technology Data Exchange (ETDEWEB)

Grabaskas, David S. [Argonne National Lab. (ANL), Argonne, IL (United States); Brunett, Acacia Joann [Argonne National Lab. (ANL), Argonne, IL (United States); Bucknor, Matthew D. [Argonne National Lab. (ANL), Argonne, IL (United States); Sienicki, James J. [Argonne National Lab. (ANL), Argonne, IL (United States); Sofu, Tanju [Argonne National Lab. (ANL), Argonne, IL (United States)

2015-02-28

Construction and operation of a nuclear power installation in the U.S. requires licensing by the U.S. Nuclear Regulatory Commission (NRC). A vital part of this licensing process and integrated safety assessment entails the analysis of a source term (or source terms) that represents the release of radionuclides during normal operation and accident sequences. Historically, nuclear plant source term analyses have utilized deterministic, bounding assessments of the radionuclides released to the environment. Significant advancements in technical capabilities and the knowledge state have enabled the development of more realistic analyses such that a mechanistic source term (MST) assessment is now expected to be a requirement of advanced reactor licensing. This report focuses on the state of development of an MST for a sodium fast reactor (SFR), with the intent of aiding in the process of MST definition by qualitatively identifying and characterizing the major sources and transport processes of radionuclides. Due to common design characteristics among current U.S. SFR vendor designs, a metal-fuel, pool-type SFR has been selected as the reference design for this work, with all phenomenological discussions geared toward this specific reactor configuration. This works also aims to identify the key gaps and uncertainties in the current knowledge state that must be addressed for SFR MST development. It is anticipated that this knowledge state assessment can enable the coordination of technology and analysis tool development discussions such that any knowledge gaps may be addressed. Sources of radionuclides considered in this report include releases originating both in-vessel and ex-vessel, including in-core fuel, primary sodium and cover gas cleanup systems, and spent fuel movement and handling. Transport phenomena affecting various release groups are identified and qualitatively discussed, including fuel pin and primary coolant retention, and behavior in the cover gas and

Dealing with extreme data diversity: extraction and fusion from the growing types of document formats

Science.gov (United States)

David, Peter; Hansen, Nichole; Nolan, James J.; Alcocer, Pedro

2015-05-01

The growth in text data available online is accompanied by a growth in the diversity of available documents. Corpora with extreme heterogeneity in terms of file formats, document organization, page layout, text style, and content are common. The absence of meaningful metadata describing the structure of online and open-source data leads to text extraction results that contain no information about document structure and are cluttered with page headers and footers, web navigation controls, advertisements, and other items that are typically considered noise. We describe an approach to document structure and metadata recovery that uses visual analysis of documents to infer the communicative intent of the author. Our algorithm identifies the components of documents such as titles, headings, and body content, based on their appearance. Because it operates on an image of a document, our technique can be applied to any type of document, including scanned images. Our approach to document structure recovery considers a finer-grained set of component types than prior approaches. In this initial work, we show that a machine learning approach to document structure recovery using a feature set based on the geometry and appearance of images of documents achieves a 60% greater F1- score than a baseline random classifier.

A simplified approach to estimating reference source terms for LWR designs

International Nuclear Information System (INIS)

1999-12-01

systems. The publication of this IAEA technical document represents the conclusion of a task, initiated in 1996, devoted to the estimation of the radioactive source term in nuclear reactors. It focuses mainly on light water reactors (LWRs)

Source terms for analysis of accidents at a high level waste repository

International Nuclear Information System (INIS)

Mubayi, V.; Davis, R.E.; Youngblood, R.

1989-01-01

This paper describes an approach to identifying source terms from possible accidents during the preclosure phase of a high-level nuclear waste repository. A review of the literature on repository safety analyses indicated that source term estimation is in a preliminary stage, largely based on judgement-based scoping analyses. The approach developed here was to partition the accident space into domains defined by certain threshold values of temperature and impact energy density which may arise in potential accidents and specify release fractions of various radionuclides, present in the waste form, in each domain. Along with a more quantitative understanding of accident phenomenology, this approach should help in achieving a clearer perspective on scenarios important to preclosure safety assessments of geologic repositories. 18 refs., 3 tabs

Use of 7Be to document soil erosion associated with a short period of extreme rainfall

International Nuclear Information System (INIS)

Sepulveda, A.; Schuller, P.; Walling, D.E.; Castillo, A.

2008-01-01

Intensification and expansion of agricultural production since the 1970s have increased soil erosion problems in south-central Chile. Quantitative information on soil loss is needed for erosion risk assessment and to establish the effectiveness of improved land management practices. Since information from traditional sources, such as erosion plots, is limited, attention has been directed to the use of environmental radionuclides for documenting erosion rates. Cs-137 has been successfully utilised for this purpose, but only provides information on medium-term erosion rates. There is also a need to document event-related soil erosion. This paper outlines the basis for using 7 Be measurements to document short-term erosion and reports its successful use for quantifying the erosion that occurred within an arable field, as a result of a period of heavy rainfall (400 mm in 27 days) occurring in May 2005. The study field had been under a no-till, no-burning system for 18 years, but immediately prior to the period of heavy rainfall the harvest residues were burnt. The erosion recorded therefore reflected both the extreme nature of the rainfall and the effects of the burning in increasing surface runoff and erosion. The sampled area corresponded to that used previously by the authors to document the medium-term erosion rates associated with both conventional tillage and the subsequent switch to a no-till system. Comparisons between the erosion documented for the period of heavy rainfall in 2005 with these medium-term erosion rates permits some tentative conclusions regarding the importance of extreme events and the impact of burning in increasing the erosion associated with the no-till system

Long-term dust aerosol production from natural sources in Iceland.

Science.gov (United States)

Dagsson-Waldhauserova, Pavla; Arnalds, Olafur; Olafsson, Haraldur

2017-02-01

Iceland is a volcanic island in the North Atlantic Ocean with maritime climate. In spite of moist climate, large areas are with limited vegetation cover where >40% of Iceland is classified with considerable to very severe erosion and 21% of Iceland is volcanic sandy deserts. Not only do natural emissions from these sources influenced by strong winds affect regional air quality in Iceland ("Reykjavik haze"), but dust particles are transported over the Atlantic ocean and Arctic Ocean >1000 km at times. The aim of this paper is to place Icelandic dust production area into international perspective, present long-term frequency of dust storm events in northeast Iceland, and estimate dust aerosol concentrations during reported dust events. Meteorological observations with dust presence codes and related visibility were used to identify the frequency and the long-term changes in dust production in northeast Iceland. There were annually 16.4 days on average with reported dust observations on weather stations within the northeastern erosion area, indicating extreme dust plume activity and erosion within the northeastern deserts, even though the area is covered with snow during the major part of winter. During the 2000s the highest occurrence of dust events in six decades was reported. We have measured saltation and Aeolian transport during dust/volcanic ash storms in Iceland, which give some of the most intense wind erosion events ever measured. Icelandic dust affects the ecosystems over much of Iceland and causes regional haze. It is likely to affect the ecosystems of the oceans around Iceland, and it brings dust that lowers the albedo of the Icelandic glaciers, increasing melt-off due to global warming. The study indicates that Icelandic dust may contribute to the Arctic air pollution. Long-term records of meteorological dust observations from Northeast Iceland indicate the frequency of dust events from Icelandic deserts. The research involves a 60-year period and

7 CFR 1735.46 - Loan security documents.

Science.gov (United States)

2010-01-01

... 7 Agriculture 11 2010-01-01 2010-01-01 false Loan security documents. 1735.46 Section 1735.46... § 1735.46 Loan security documents. (a) Loans are to be repaid according to their terms. RUS generally... subordinations. (b) Loan security documents of borrowers with loans approved after October 6, 1997 will provide...

ENDF/B summary documentation

International Nuclear Information System (INIS)

Kinsey, R.

1979-07-01

This publication provides a localized source of descriptions for the evaluations contained in the ENDF/B Library. The summary documentation presented is intended to be a more detailed description than the (File 1) comments contained in the computer readable data files, but not so detailed as the formal reports describing each ENDF/B evaluation. The summary documentations were written by the CSEWB (Cross Section Evaluation Working Group) evaluators and compiled by NNDC (National Nuclear Data Center). This edition includes documentation for materials found on ENDF/B Version V tapes 501 to 516 (General Purpose File) excluding tape 504. ENDF/B-V also includes tapes containing partial evaluations for the Special Purpose Actinide (521, 522), Dosimetry (531), Activation (532), Gas Production (533), and Fission Product (541-546) files. The materials found on these tapes are documented elsewhere. Some of the evaluation descriptions in this report contain cross sections or energy level information

Evaluation of short- and long-term fission product sources at the Fukushima Daiichi NPP

International Nuclear Information System (INIS)

Uchida, Shunsuke; Naitoh, Masanori; Suzuki, Hiroaki; Okada, Hidetoshi; Pellegrini, Marco; Achilli, Andrea; Hanamoto, Yukio; Sasaki, Hiroaki

2014-01-01

Research on fission product (FP) behaviors used to be one of the most important subjects in water chemistry but it is not done nowadays as a consequence of the increased integrity of nuclear fuels and the minimization of FP release into the environment. Evaluation of FP release into the environment is still one of the key issues for severe accident analysis, though. Although there have been a long quiet period in nuclear safety research, how to detect initiation of severe accidents, how to prevent them and how to mitigate them are still important subjects for nuclear engineering, and how to control the severe accidents after their occurrence, especially how to control FP release into the environment, has seldom been discussed in the water chemistry group recently. The paper is intended to address the issue of fewer activities for FP studies. FP sources are divided into two categories, short- and long-term FP sources. Short-term FP source can be evaluated based on the measured data obtained from monitoring posts (MPs), which give us clear evidence on the importance of radioactive iodine and cesium releases into the environment. It used to be considered that during primary containment vessel (PCV) venting, release of each element, e.g., iodine and cesium, was determined by the suppression pool scrubbing efficiency and most of the cesium would likely be removed in the pool due to its large scrubbing efficiency. But as a result of analyzing the MP data at early stage of the Fukushima Daiichi nuclear power plant (NPP) accident, it was confirmed that the releases of both elements were in proportion to their inventories in the reactors and their scrubbing efficiencies were almost the same. The scrubbing efficiency which increased with the pool water temperature became almost the same for iodine and cesium around the pool water boiling temperature. As a result of the mass balance analysis for FPs in the contaminated water accumulated in the Fukushima Daiichi plant site, it

Sources for charged particles; Les sources de particules chargees

Energy Technology Data Exchange (ETDEWEB)

Arianer, J.

1997-09-01

This document is a basic course on charged particle sources for post-graduate students and thematic schools on large facilities and accelerator physics. A simple but precise description of the creation and the emission of charged particles is presented. This course relies on every year upgraded reference documents. Following relevant topics are considered: electronic emission processes, technological and practical considerations on electron guns, positron sources, production of neutral atoms, ionization, plasma and discharge, different types of positive and negative ion sources, polarized particle sources, materials for the construction of ion sources, low energy beam production and transport. (N.T.).

Application for approval of derived authorized limits for the release of the 190-C trenches and 105-C process water tunnels at the Hanford Site: Volume 2 - source term development

International Nuclear Information System (INIS)

Denham, D.H.; Winslow, S.L.; Moeller, M.P.; Kennedy, W.E. Jr.

1997-03-01

As part of environmental restoration activities at the Hanford Site, Bechtel Hanford, Inc. is conducting a series of evaluations to determine appropriate release conditions for specific facilities following the completion of decontamination and decommissioning projects. The release conditions, with respect to the residual volumetric radioactive contamination, are termed authorized limits. This report presents the summary of the supporting information and the final application for approval of derived authorized limits for the release of the 190-C trenches and the 105-C process water tunnels. This document contains two volumes; this volume (Vol. 2) contains the radiological characterization data, spreadsheet analyses, and radiological source terms

Source-term characterisation and solid speciation of plutonium at the Semipalatinsk NTS, Kazakhstan.

Science.gov (United States)

Nápoles, H Jiménez; León Vintró, L; Mitchell, P I; Omarova, A; Burkitbayev, M; Priest, N D; Artemyev, O; Lukashenko, S

2004-01-01

New data on the concentrations of key fission/activation products and transuranium nuclides in samples of soil and water from the Semipalatinsk Nuclear Test Site are presented and interpreted. Sampling was carried out at Ground Zero, Lake Balapan, the Tel'kem craters and reference locations within the test site boundary well removed from localised sources. Radionuclide ratios have been used to characterise the source term(s) at each of these sites. The geochemical partitioning of plutonium has also been examined and it is shown that the bulk of the plutonium contamination at most of the sites examined is in a highly refractory, non-labile form.

Source-term characterisation and solid speciation of plutonium at the Semipalatinsk NTS, Kazakhstan

Energy Technology Data Exchange (ETDEWEB)

Napoles, H.J.H. Jimenez; Leon Vintro, L. E-mail: luis.leon@ucd.ie; Mitchell, P.I.; Omarova, A.; Burkitbayev, M.; Priest, N.D.; Artemyev, O.; Lukashenko, S

2004-09-01

New data on the concentrations of key fission/activation products and transuranium nuclides in samples of soil and water from the Semipalatinsk Nuclear Test Site are presented and interpreted. Sampling was carried out at Ground Zero, Lake Balapan, the Tel'kem craters and reference locations within the test site boundary well removed from localised sources. Radionuclide ratios have been used to characterise the source term(s) at each of these sites. The geochemical partitioning of plutonium has also been examined and it is shown that the bulk of the plutonium contamination at most of the sites examined is in a highly refractory, non-labile form.

BioAnnote: a software platform for annotating biomedical documents with application in medical learning environments.

Science.gov (United States)

López-Fernández, H; Reboiro-Jato, M; Glez-Peña, D; Aparicio, F; Gachet, D; Buenaga, M; Fdez-Riverola, F

2013-07-01

Automatic term annotation from biomedical documents and external information linking are becoming a necessary prerequisite in modern computer-aided medical learning systems. In this context, this paper presents BioAnnote, a flexible and extensible open-source platform for automatically annotating biomedical resources. Apart from other valuable features, the software platform includes (i) a rich client enabling users to annotate multiple documents in a user friendly environment, (ii) an extensible and embeddable annotation meta-server allowing for the annotation of documents with local or remote vocabularies and (iii) a simple client/server protocol which facilitates the use of our meta-server from any other third-party application. In addition, BioAnnote implements a powerful scripting engine able to perform advanced batch annotations. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Fission product source term research at Oak Ridge National Laboratory

International Nuclear Information System (INIS)

Malinauskas, A.P.

1985-01-01

The purpose of this work is to describe some of the research being performed at ORNL in support of the effort to describe, as realistically as possible, fission product source terms for nuclear reactor accidents. In order to make this presentation manageable, only those studies directly concerned with fission product behavior, as opposed to thermal hydraulics, accident sequence progression, etc., will be discussed

Standards for Documenting Finite‐Fault Earthquake Rupture Models

KAUST Repository

Mai, Paul Martin

2016-04-06

In this article, we propose standards for documenting and disseminating finite‐fault earthquake rupture models, and related data and metadata. A comprehensive documentation of the rupture models, a detailed description of the data processing steps, and facilitating the access to the actual data that went into the earthquake source inversion are required to promote follow‐up research and to ensure interoperability, transparency, and reproducibility of the published slip‐inversion solutions. We suggest a formatting scheme that describes the kinematic rupture process in an unambiguous way to support subsequent research. We also provide guidelines on how to document the data, metadata, and data processing. The proposed standards and formats represent a first step to establishing best practices for comprehensively documenting input and output of finite‐fault earthquake source studies.

Standards for Documenting Finite‐Fault Earthquake Rupture Models

KAUST Repository

Mai, Paul Martin; Shearer, Peter; Ampuero, Jean‐Paul; Lay, Thorne

2016-01-01

In this article, we propose standards for documenting and disseminating finite‐fault earthquake rupture models, and related data and metadata. A comprehensive documentation of the rupture models, a detailed description of the data processing steps, and facilitating the access to the actual data that went into the earthquake source inversion are required to promote follow‐up research and to ensure interoperability, transparency, and reproducibility of the published slip‐inversion solutions. We suggest a formatting scheme that describes the kinematic rupture process in an unambiguous way to support subsequent research. We also provide guidelines on how to document the data, metadata, and data processing. The proposed standards and formats represent a first step to establishing best practices for comprehensively documenting input and output of finite‐fault earthquake source studies.

Proposal for implementation of alternative source term in the nuclear power plant of Laguna Verde

International Nuclear Information System (INIS)

Bazan L, A.; Lopez L, M.; Vargas A, A.; Cardenas J, J. B.

2009-10-01

In 2010 the nuclear power plant of Laguna Verde will implement the extended power upbeat in both units of the plant. Agree with methodology of NEDC-33004P-A, (constant pressure power up rate), and the source term of core, for accidents evaluations, were increased in proportion to the ratio of power level. This means that for the case of a design basis accident of loss of coolant an increase of power of 15% originated an increase of 15% in dose to main control room. Using the method of NEDC-33004P-A to extended power upbeat conditions was determined that the dose value to main control room is very near to regulatory limit established by SRP 6.4. By the above and in order to recover the margin, the nuclear power plant of Laguna Verde will calculate an alternative source term following the criteria established in RG 1.183 (alternative radiological source term for evaluating DBA at nuclear power reactor). This approach also have a more realistic dose value using the criterion of 10-CFR-50.67, in addition is predicted to get the benefit of additional operational flexibilities. This paper present the proposal of implementing the alternative source term in Laguna Verde. (Author)

Multiple sclerosis documentation system (MSDS): moving from documentation to management of MS patients.

Science.gov (United States)

Ziemssen, Tjalf; Kempcke, Raimar; Eulitz, Marco; Großmann, Lars; Suhrbier, Alexander; Thomas, Katja; Schultheiss, Thorsten

2013-09-01

The long disease duration of multiple sclerosis and the increasing therapeutic options require a individualized therapeutic approach which should be carefully documented over years of observation. To switch from MS documentation to an innovative MS management, new computer- and internet-based tools could be implemented as we could demonstrate with the novel computer-based patient management system "multiple sclerosis management system 3D" (MSDS 3D). MSDS 3D allows documentation and management of visit schedules and mandatory examinations via defined study modules by integration of data input from various sources (patients, attending physicians and MS nurses). It provides forms for the documentation of patient visits as well as clinical and diagnostic findings. Information can be collected via interactive touch screens. Specific modules allow the management of highly efficacious treatments as natalizumab or fingolimod. MSDS can be used to transfer the documented data to databases as, e.g. the registry of the German MS society or REGIMS. MSDS has already been implemented successfully in clinical practice and is currently being evaluated in a multicenter setting. High-quality management and documentation are crucial for improvements in clinical practice and research work.

Review of the accident source terms for aluminide fuel: Application to the BR2 reactor

International Nuclear Information System (INIS)

Joppen, F.

2005-01-01

A major safety review of the BR2, a material test reactor, is to be conducted for the year 2006. One of the subjects selected for the safety review is the definition of source terms for emergency planning and in particular the development of accident scenarios. For nuclear power plants the behaviour of fuel under accident conditions is a well studied object. In case of non-power reactors this basic knowledge is rather scarce. The usefulness of information from power plant fuels is limited due to the differences in fuel type, power level and thermohydraulical conditions. First investigation indicates that using data from power plant fuel leads to an overestimation of the source terms. Further research on this subject could be very useful for the research reactor community, in order to define more realistic source terms and to improve the emergency preparedness. (author)

The long-term relationships among China's energy consumption sources and adjustments to its renewable energy policy

International Nuclear Information System (INIS)

Zou Gaolu

2012-01-01

To reduce its consumption of coal and oil in its primary energy consumption, China promotes the development of renewable energy resources. I have analysed the long-term relationship among China's primary energy consumption sources. Changes in coal consumption lead those in the consumption of other energy sources in the long term. Coal and oil fuels substitute for each other equally. The long-term elasticities of China's coal consumption relative to its hydroelectricity consumption were greater than one and nearly equal during the two sample periods. Therefore, increased hydroelectricity consumption did not imply a reduction in coal consumption. China holds abundant hydroelectricity, wind and, solar energy potential. China must prevent an excessive escalation of its economy and resultant energy demand to realise a meaningful substitution of coal with hydroelectricity. Moreover, China must develop and use wind and solar energy sources. Natural gas can be a good substitute for coal, given its moderate price growth and affordable price levels. - Highlights: ► Coal consumption changes lead those of other energy sources in the long term. ► Coal and oil fuels substitute for each other equally. ► Increased hydroelectricity consumption has not meant lower coal consumption. ► Wind, solar and natural gas are China's promising energy sources.

Integrated system for automated financial document processing

Science.gov (United States)

Hassanein, Khaled S.; Wesolkowski, Slawo; Higgins, Ray; Crabtree, Ralph; Peng, Antai

1997-02-01

A system was developed that integrates intelligent document analysis with multiple character/numeral recognition engines in order to achieve high accuracy automated financial document processing. In this system, images are accepted in both their grayscale and binary formats. A document analysis module starts by extracting essential features from the document to help identify its type (e.g. personal check, business check, etc.). These features are also utilized to conduct a full analysis of the image to determine the location of interesting zones such as the courtesy amount and the legal amount. These fields are then made available to several recognition knowledge sources such as courtesy amount recognition engines and legal amount recognition engines through a blackboard architecture. This architecture allows all the available knowledge sources to contribute incrementally and opportunistically to the solution of the given recognition query. Performance results on a test set of machine printed business checks using the integrated system are also reported.

Analysis of accident sequences and source terms at treatment and storage facilities for waste generated by US Department of Energy waste management operations. Volume 1: Sections 1-9

International Nuclear Information System (INIS)

Mueller, C.; Nabelssi, B.; Roglans-Ribas, J.; Folga, S.; Policastro, A.; Freeman, W.; Jackson, R.; Mishima, J.; Turner, S.

1996-12-01

This report documents the methodology, computational framework, and results of facility accident analyses performed for the US Department of Energy (DOE) Waste Management Programmatic Environmental Impact Statement (WM PEIS). The accident sequences potentially important to human health risk are specified, their frequencies assessed, and the resultant radiological and chemical source terms evaluated. A personal-computer-based computational framework and database have been developed that provide these results as input to the WM PEIS for the calculation of human health risk impacts. The WM PEIS addresses management of five waste streams in the DOE complex: low-level waste (LLW), hazardous waste (HW), high-level waste (HLW), low-level mixed waste (LLMW), and transuranic waste (TRUW). Currently projected waste generation rates, storage inventories, and treatment process throughputs have been calculated for each of the waste streams. This report summarizes the accident analyses and aggregates the key results for each of the waste streams. Source terms are estimated, and results are presented for each of the major DOE sites and facilities by WM PEIS alternative for each waste stream. Key assumptions in the development of the source terms are identified. The appendices identify the potential atmospheric release of each toxic chemical or radionuclide for each accident scenario studied. They also discuss specific accident analysis data and guidance used or consulted in this report

Development of in-vessel source term analysis code, tracer

International Nuclear Information System (INIS)

Miyagi, K.; Miyahara, S.

1996-01-01

Analyses of radionuclide transport in fuel failure accidents (generally referred to source terms) are considered to be important especially in the severe accident evaluation. The TRACER code has been developed to realistically predict the time dependent behavior of FPs and aerosols within the primary cooling system for wide range of fuel failure events. This paper presents the model description, results of validation study, the recent model advancement status of the code, and results of check out calculations under reactor conditions. (author)

ENDF/B summary documentation

Energy Technology Data Exchange (ETDEWEB)

Kinsey, R. (comp.)

1979-07-01

This publication provides a localized source of descriptions for the evaluations contained in the ENDF/B Library. The summary documentation presented is intended to be a more detailed description than the (File 1) comments contained in the computer readable data files, but not so detailed as the formal reports describing each ENDF/B evaluation. The summary documentations were written by the CSEWB (Cross Section Evaluation Working Group) evaluators and compiled by NNDC (National Nuclear Data Center). This edition includes documentation for materials found on ENDF/B Version V tapes 501 to 516 (General Purpose File) excluding tape 504. ENDF/B-V also includes tapes containing partial evaluations for the Special Purpose Actinide (521, 522), Dosimetry (531), Activation (532), Gas Production (533), and Fission Product (541-546) files. The materials found on these tapes are documented elsewhere. Some of the evaluation descriptions in this report contain cross sections or energy level information. (RWR)

Quantification of source-term profiles from near-field geochemical models

International Nuclear Information System (INIS)

McKinley, I.G.

1985-01-01

A geochemical model of the near-field is described which quantitatively treats the processes of engineered barrier degradation, buffering of aqueous chemistry by solid phases, nuclide solubilization and transport through the near-field and release to the far-field. The radionuclide source-terms derived from this model are compared with those from a simpler model used for repository safety analysis. 10 refs., 2 figs., 2 tabs

Modelling and simulation the radioactive source-term of fission products in PWR type reactors

International Nuclear Information System (INIS)

Porfirio, Rogilson Nazare da Silva

1996-01-01

The source-term was defined with the purpose the quantify all radioactive nuclides released the nuclear reactor in the case of accidents. Nowadays the source-term is limited to the coolant of the primary circuit of reactors and may be measured or modelled with computer coders such as the TFP developed in this work. The calculational process is based on the linear chain techniques used in the CINDER-2 code. The TFP code considers forms of fission products release from the fuel pellet: Recoil, Knockout and Migration. The release from the gap to the coolant fluid is determined from the ratio between activity measured in the coolant and calculated activity in the gap. Considered the operational data of SURRY-1 reactor, the TFP code was run to obtain the source=term of this reactor. From the measured activities it was verified the reliability level of the model and the employed computational logic. The accuracy of the calculated quantities were compared to the measured data was considered satisfactory. (author)

Derivation of the source term, dose results and associated radiological consequences for the Greek Research Reactor – 1

Energy Technology Data Exchange (ETDEWEB)

Pappas, Charalampos, E-mail: chpappas@ipta.demokritos.gr; Ikonomopoulos, Andreas; Sfetsos, Athanasios; Andronopoulos, Spyros; Varvayanni, Melpomeni; Catsaros, Nicolas

2014-07-01

Highlights: • Source term derivation of postulated accident sequences in a research reactor. • Various containment ventilation scenarios considered for source term calculations. • Source term parametric analysis performed in case of lack of ventilation. • JRODOS employed for dose calculations under eighteen modeled scenarios. • Estimation of radiological consequences during typical and adverse weather scenarios. - Abstract: The estimated source term, dose results and radiological consequences of selected accident sequences in the Greek Research Reactor – 1 are presented and discussed. A systematic approach has been adopted to perform the necessary calculations in accordance with the latest computational developments and IAEA recommendations. Loss-of-coolant, reactivity insertion and fuel channel blockage accident sequences have been selected to derive the associated source terms under three distinct containment ventilation scenarios. Core damage has been conservatively assessed for each accident sequence while the ventilation has been assumed to function within the efficiency limits defined at the Safety Analysis Report. In case of lack of ventilation a parametric analysis is also performed to examine the dependency of the source term on the containment leakage rate. A typical as well as an adverse meteorological scenario have been defined in the JRODOS computational platform in order to predict the effective, lung and thyroid doses within a region defined by a 15 km radius downwind from the reactor building. The radiological consequences of the eighteen scenarios associated with the accident sequences are presented and discussed.

Electronic Document Management Using Inverted Files System

Science.gov (United States)

Suhartono, Derwin; Setiawan, Erwin; Irwanto, Djon

2014-03-01

The amount of documents increases so fast. Those documents exist not only in a paper based but also in an electronic based. It can be seen from the data sample taken by the SpringerLink publisher in 2010, which showed an increase in the number of digital document collections from 2003 to mid of 2010. Then, how to manage them well becomes an important need. This paper describes a new method in managing documents called as inverted files system. Related with the electronic based document, the inverted files system will closely used in term of its usage to document so that it can be searched over the Internet using the Search Engine. It can improve document search mechanism and document save mechanism.

Electronic Document Management Using Inverted Files System

Directory of Open Access Journals (Sweden)

Suhartono Derwin

2014-03-01

Full Text Available The amount of documents increases so fast. Those documents exist not only in a paper based but also in an electronic based. It can be seen from the data sample taken by the SpringerLink publisher in 2010, which showed an increase in the number of digital document collections from 2003 to mid of 2010. Then, how to manage them well becomes an important need. This paper describes a new method in managing documents called as inverted files system. Related with the electronic based document, the inverted files system will closely used in term of its usage to document so that it can be searched over the Internet using the Search Engine. It can improve document search mechanism and document save mechanism.

Source term and activation calculations for the new TR-FLEX cyclotron for medical applications at HZDR

Energy Technology Data Exchange (ETDEWEB)

Konheiser, Joerg [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Reactor Safety; Ferrari, A. [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Inst. of Radiation Physics; Magin, A. [Karlsruher Institut fuer Technologie (KIT), Karlsruhe (Germany); Naumann, B. [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Dept. of Radiation Protection and Safety; Mueller, S.E.

2017-06-01

The neutron source terms for a proton beam hitting an {sup 18}O-enriched water target were calculated with the radiation transport programs MCNP6 and FLUKA and were compared to source terms for exclusive {sup 18}O(p,n){sup 18}F production. To validate the radiation fields obtained in the simulations, an experimental program has been started using activation samples originally used in reactor dosimetry.

Managing the consistency of distributed documents

OpenAIRE

Nentwich, C.

2005-01-01

Many businesses produce documents as part of their daily activities: software engineers produce requirements specifications, design models, source code, build scripts and more; business analysts produce glossaries, use cases, organisation charts, and domain ontology models; service providers and retailers produce catalogues, customer data, purchase orders, invoices and web pages. What these examples have in common is that the content of documents is often semantically relate...

An Introduction to Document Imaging in the Financial Aid Office.

Science.gov (United States)

Levy, Douglas A.

2001-01-01

First describes the components of a document imaging system in general and then addresses this technology specifically in relation to financial aid document management: its uses and benefits, considerations in choosing a document imaging system, and additional sources for information. (EV)

Use of source term uncoupled in radionuclide migration equations

International Nuclear Information System (INIS)

Silveira, Claudia Siqueira da; Lima, Zelmo Rodrigues de; Alvim, Antonio Carlos Marques

2008-01-01

Final repositories of high-level radioactive waste have been considered in deep, low permeability and stable geological formations. A common problem found is the migration modeling of radionuclides in a fractured rock. In this work, the physical system adopted consists of the rock matrix containing a single planar fracture situated in water saturated porous rock. The partial differential equations that describe the radionuclide transport were discretized using finite differences techniques, of which the following methods were adopted: Explicit Euler, Implicit Euler and Crank-Nicholson. For each one of these methods, the advective term was discretized with the following numerical schemes: backward differences, centered differences and forward differences. We make a comparison to determine which temporal and space discretization has the best result in relation to a reference solution. The obtained results show that the Explicit Euler Method with forward discretization in the advective term has a good accuracy. Next, with the objective of improving the answer of the Implicit Euler and Crank-Nicholson Methods it was accomplished a source term uncouplement, the diffusive flux. The obtained results were considered satisfactory by comparison with previous studies. (author)

Comment and response document for the long-term surveillance plan for the Bodo Canyon Disposal Site, Durango, Colorado, Revision 0

International Nuclear Information System (INIS)

1995-11-01

This report contains the comment and response document for the Draft Long-Term Surveillance Plan of the Bodo Canyon Site in Durango, California. This is a part of the Uranium Mill Tailings Remedial Action (UMTRA) Project. Questions and comments regarding specific sections or statements in the report are described and then a response to each review comment or question is provided

Short-term X-ray variability of the globular cluster source 4U 1820 - 30 (NGC 6624)

Science.gov (United States)

Stella, L.; Kahn, S. M.; Grindlay, J. E.

1984-01-01

Analytical techniques for improved identification of the temporal and spectral variability properties of globular cluster and galactic bulge X-ray sources are described in terms of their application to a large set of observations of the source 4U 1820 - 30 in the globular cluster NGC 6624. The autocorrelation function, cross-correlations, time skewness function, erratic periodicities, and pulse trains are examined. The results are discussed in terms of current models with particular emphasis on recent accretion disk models. It is concluded that the analyzed observations provide the first evidence for shot-noise variability in a globular cluster X-ray source.

Source term development for the 300 Area Treated Effluent Disposal Facility

International Nuclear Information System (INIS)

Bendixsen, R.B.

1994-04-01

A novel method for developing a source term for radiation and hazardous material content of sludge processing equipment and barrels in a new waste water treatment facility is presented in this paper. The 300 Area Treated Effluent Disposal Facility (TEDF), located at the Hanford Site near Richland, Washington, will treat process sewer waste water from the 300 Area and discharge a permittable effluent flow into the Columbia River. A process information and hazards analysis document needed a process flowsheet detailing the concentrations of radionuclides, inorganics, and organics throughout the process, including the sludge effluent flow. A hazards analysis for a processing facility usually includes a flowsheet showing the process, materials, heat balances, and instrumentation for that facility. The flow sheet estimates stream flow quantities, activities, compositions, and properties. For the 300 Area TEDF, it was necessary to prepare the flow sheet with all of the information so that radiation doses to workers could be estimated. The noble method used to develop the 300 Area TEDF flowsheet included generating recycle factors. To prepare each component in the flowsheet, precipitation, destruction, and two recycle factors were developed. The factors were entered into a spreadsheet and provided a method of estimating the steady-state concentrations of all of the components in the facility. This report describes how the factors were developed, explains how they were used in developing the flowsheet, and presents the results of using these values to estimate radiation doses for personnel working in the facility. The report concludes with a discussion of the effect of estimates of radioactive and hazardous material concentrations on shielding design and the need for containment features for equipment in the facility

Influence of Chemistry on source term assessment

International Nuclear Information System (INIS)

Herranz Puebla, L.E.; Lopez Diez, I.; Rodriguez Maroto, J.J.; Martinez Lopez-Alcorocho, A.

1991-01-01

The major goal of a phenomenology analysis of containment during a severe accident situation can be splitedd into the following ones: to know the containment response to the different loads and to predict accurately the fission product and aerosol behavior. In this report, the main results coming from the study of a hypothetical accident scenario, based on LA-4 experiment of LACE project, are presented. In order to do it, several codes have been coupled: CONTEMPT4/MOD5 (thermalhydraulics), NAUA/MOD5 (aerosol physics) and IODE (iodine chemistry). 12 refs. It has been demonstrated the impossibility of assessing with confidence the Source Term if the chemical conduct of some radionuclides is not taken into account. In particular, the influence on the iodine retention efficiency of the sump of variables such as pH has been proven. (Author). 12 refs

Two-stage Framework for a Topology-Based Projection and Visualization of Classified Document Collections

Energy Technology Data Exchange (ETDEWEB)

Oesterling, Patrick; Scheuermann, Gerik; Teresniak, Sven; Heyer, Gerhard; Koch, Steffen; Ertl, Thomas; Weber, Gunther H.

2010-07-19

During the last decades, electronic textual information has become the world's largest and most important information source available. People have added a variety of daily newspapers, books, scientific and governmental publications, blogs and private messages to this wellspring of endless information and knowledge. Since neither the existing nor the new information can be read in its entirety, computers are used to extract and visualize meaningful or interesting topics and documents from this huge information clutter. In this paper, we extend, improve and combine existing individual approaches into an overall framework that supports topological analysis of high dimensional document point clouds given by the well-known tf-idf document-term weighting method. We show that traditional distance-based approaches fail in very high dimensional spaces, and we describe an improved two-stage method for topology-based projections from the original high dimensional information space to both two dimensional (2-D) and three dimensional (3-D) visualizations. To show the accuracy and usability of this framework, we compare it to methods introduced recently and apply it to complex document and patent collections.

SARNET. Severe Accident Research Network - key issues in the area of source term

International Nuclear Information System (INIS)

Giordano, P.; Micaelli, J.C.; Haste, T.; Herranz, L.

2005-01-01

About fifty European organisations integrate in SARNET (Network of Excellence of the EU 6 th Framework Programme) their research capacities in resolve better the most important remaining uncertainties and safety issues concerning existing and future Nuclear Power Plants (NPPs) under hypothetical Severe Accident (SA) conditions. Wishing to maintain a long-lasting cooperation, they conduct three types of activities: integrating activities, spreading of excellence and jointly executed research. This paper summarises the main results obtained by the network after the first year, giving more prominence to those from jointly executed research in the Source Term area. Integrating activities have been performed through different means: the ASTEC integral computer code for severe accident transient modelling, through development of PSA2 methodologies, through the setting of a structure for definition of evolving R and D priorities and through the development of a web-network of data bases that hosts experimental data. Such activities have been facilitated by the development of an Advanced Communication Tool. Concerning spreading of excellence, educational courses covering Severe Accident Analysis Methodology and Level 2 PSA have been set up, to be given in early 2006. A detailed text book on Severe Accident Phenomenology has been designed and agreed amongst SARNET members. A mobility programme for students and young researchers is being developed, some detachments are already completed or in progress, and examples are quoted. Jointly executed research activities concern key issues grouped in the Corium, Containment and Source Term areas. In Source Term, behaviour of the highly radio-toxic ruthenium under oxidising conditions (like air ingress) for HBU and MOX fuel has been investigated. First modelling proposals for ASTEC have been made for oxidation of fuel and of ruthenium. Experiments on transport of highly volatile oxide ruthenium species have been performed. Reactor

Evaluation of applicability of alternative source terms to operating nuclear power plants in Korea

International Nuclear Information System (INIS)

Lim, S. N.; Park, Y. S.; Nam, K. M.; Song, D. B.; Bae, Y. J.; Lee, Y. J.; Jung, C. Y.

2002-01-01

In 1995 and 2000, NRC issued NUREG-1465 and Regulatory Guide 1.183 with respect to Alternative Source Terms(AST) replacing the existing source terms of TID-14844 and Regulatory Guide 1.4, 1.25, and 1.77 for radiological Design Basis Accidents(DBA) analysis. In 1990, ICRP published ICRP Pub. 60 which represents new recommendations on dose criteria and concepts. In Korea, alternative source terms were used for evaluation of effective doses for design basis accidents of Advanced Power Reactor(APR1400) using the computer program developed by an overseas company. Recently, DBADOSE, new computer program for DBA analysis incorporating AST and effective dose concept was developed by KHNP and KOPEC, and reanalysis applying AST to operating nuclear power plants, Kori units 3 and 4 in Korea using DBADOSE has been performed. As the results of this analysis, it was concluded that some conservative variables or operation procedures of operating plants could be mitigated or simplified by virtue of increased safety margin and consequently, economical and operational benefits ensue. In this paper, methodologies and results of Kori 3 and 4 DBA reanalysis and sensitivity analysis for mitigation of main design variables are introduced

Long term leaching of chlorinated solvents from source zones in low permeability settings with fractures

DEFF Research Database (Denmark)

Bjerg, Poul Løgstrup; Chambon, Julie Claire Claudia; Troldborg, Mads

2008-01-01

spreads to the low permeability matrix by diffusion. This results in a long term source of contamination due to back-diffusion. Leaching from such sources is further complicated by microbial degradation under anaerobic conditions to sequentially form the daughter products trichloroethylene, cis...

Source term estimation based on in-situ gamma spectrometry using a high purity germanium detector

International Nuclear Information System (INIS)

Pauly, J.; Rojas-Palma, C.; Sohier, A.

1997-06-01

An alternative method to reconstruct the source term of a nuclear accident is proposed. The technique discussed here involves the use of in-situ gamma spectrometry. The validation of the applied methodology has been possible through the monitoring of routine releases of Ar-41 originating at a Belgian site from an air cooled graphite research reactor. This technique provides a quick nuclide specific decomposition of the source term and therefore will be have an enormous potential if implemented in nuclear emergency preparedness and radiological assessments of nuclear accidents during the early phase

Integrated criteria document mercury

International Nuclear Information System (INIS)

Sloof, W.; Beelan, P. van; Annema, J.A.; Janus, J.A.

1995-01-01

The document contains a systematic review and a critical evaluation of the most relevant data on the priority substance mercury for the purpose of effect-oriented environmental policy. Chapter headings are: properties and existing standards; production, application, sources and emissions (natural sources, industry, energy, households, agriculture, dental use, waste); distribution and transformation (cinnabar; Hg 2+ , Hg 2 2+ , elemental mercury, methylmercury, behavior in soil, water, air, biota); concentrations and fluxes in the environment and exposure levels (sampling and measuring methods, occurrence in soil, water, air etc.); effects (toxicity to humans and aquatic and terrestrial systems); emissions reduction (from industrial sources, energy, waste processing etc.); and evaluation (risks, standards, emission reduction objectives, measuring strategies). 395 refs

Technical document characterization by data analysis

International Nuclear Information System (INIS)

Mauget, A.

1993-05-01

Nuclear power plants possess documents analyzing all the plant systems, which represents a vast quantity of paper. Analysis of textual data can enable a document to be classified by grouping the texts containing the same words. These methods are used on system manuals for feasibility studies. The system manual is then analyzed by LEXTER and the terms it has selected are examined. We first classify according to style (sentences containing general words, technical sentences, etc.), and then according to terms. However, it will not be possible to continue in this fashion for the 100 system manuals existing, because of lack of sufficient storage capacity. Another solution is being developed. (author)

Model documentation report: Industrial sector demand module of the National Energy Modeling System

International Nuclear Information System (INIS)

1997-01-01

This report documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Industrial Demand Model. The report catalogues and describes model assumptions, computational methodology, parameter estimation techniques, and model source code. This document serves three purposes. First, it is a reference document providing a detailed description of the NEMS Industrial Model for model analysts, users, and the public. Second, this report meets the legal requirement of the Energy Information Administration (EIA) to provide adequate documentation in support of its models. Third, it facilitates continuity in model development by providing documentation from which energy analysts can undertake model enhancements, data updates, and parameter refinements as future projects. The NEMS Industrial Demand Model is a dynamic accounting model, bringing together the disparate industries and uses of energy in those industries, and putting them together in an understandable and cohesive framework. The Industrial Model generates mid-term (up to the year 2015) forecasts of industrial sector energy demand as a component of the NEMS integrated forecasting system. From the NEMS system, the Industrial Model receives fuel prices, employment data, and the value of industrial output. Based on the values of these variables, the Industrial Model passes back to the NEMS system estimates of consumption by fuel types

Chernobyl radiocesium in freshwater fish: Long-term dynamics and sources of variation

Energy Technology Data Exchange (ETDEWEB)

Sundbom, M [Uppsala Univ., Dept. of Limnology, Uppsala (Sweden)

2002-04-01

The aim of this thesis was to investigate both the long-term temporal pattern and sources of individual variation for radiocesium in freshwater fish. The basis for the study is time series of {sup 137}Cs activity concentrations in fish from three lakes in the area North-west of Uppsala, Sweden that received considerable amounts of {sup 137}Cs from Chernobyl in may 1986. The lakes were Lake Ekholmssjoen, Lake Flatsjoen and Lake Siggeforasjoen, all small forest lakes, but with different morphometrical and chemical characteristics. The data were collected regularly, usually several times per year, during 1986-2000, using consistent methods. More than 7600 fish individuals from 7 species covering wide size ranges and feeding habits were analysed for {sup 137}Cs. For each fish was the length, weight, sex, and often the stomach contend recorded. The evaluation on long-term trends were based on data from all three lakes, while the study on sources of variation evaluated data from Lake Flatsjoen only. (au)

Chernobyl radiocesium in freshwater fish: Long-term dynamics and sources of variation

International Nuclear Information System (INIS)

Sundbom, M.

2002-01-01

The aim of this thesis was to investigate both the long-term temporal pattern and sources of individual variation for radiocesium in freshwater fish. The basis for the study is time series of 137 Cs activity concentrations in fish from three lakes in the area North-west of Uppsala, Sweden that received considerable amounts of 137 Cs from Chernobyl in may 1986. The lakes were Lake Ekholmssjoen, Lake Flatsjoen and Lake Siggeforasjoen, all small forest lakes, but with different morphometrical and chemical characteristics. The data were collected regularly, usually several times per year, during 1986-2000, using consistent methods. More than 7600 fish individuals from 7 species covering wide size ranges and feeding habits were analysed for 137 Cs. For each fish was the length, weight, sex, and often the stomach contend recorded. The evaluation on long-term trends were based on data from all three lakes, while the study on sources of variation evaluated data from Lake Flatsjoen only. (au)

Visualization of documents and concepts in neuroinformatics with the 3D-SE viewer

Directory of Open Access Journals (Sweden)

Antoine P Naud

2007-11-01

Full Text Available A new interactive visualization tool is proposed for mining text data from various fields of neuroscience. Applications to several text datasets are presented to demonstrate the capability of the proposed interactive tool to visualize complex relationships between pairs of lexical entities (with some semantic contents such as terms, keywords, posters, or papers' abstracts. Implemented as a Java applet, this tool is based on the spherical embedding (SE algorithm, which was designed for the visualization of bipartite graphs. Items such as words and documents are linked on the basis of occurrence relationships, which can be represented in a bipartite graph. These items are visualized by embedding the vertices of the bipartite graph on spheres in a three-dimensional (3-D space. The main advantage of the proposed visualization tool is that 3-D layouts can convey more information than planar or linear displays of items or graphs. Different kinds of information extracted from texts, such as keywords, indexing terms, or topics are visualized, allowing interactive browsing of various fields of research featured by keywords, topics, or research teams. A typical use of the 3D-SE viewer is quick browsing of topics displayed on a sphere, then selecting one or several item(s displays links to related terms on another sphere representing, e.g., documents or abstracts, and provides direct online access to the document source in a database, such as the Visiome Platform or the SfN Annual Meeting. Developed as a Java applet, it operates as a tool on top of existing resources.

Basic repository source term and data sheet report: Davis Canyon

International Nuclear Information System (INIS)

1988-01-01

This report is one of series describing studies undertaken in support of the US Department of Energy Civilian Radioactive Waste Management (CRWM) Program. This study contains the derivation of values for environmental source terms and resources consumed for a CRWM repository. Estimates include heavy construction equipment; support equipment; shaft-sinking equipment; transportation equipment; and consumption of fuel, water electricity, and natural gas. Data are presented for construction and operation at an assumed site in Davis Canyon, Utah. 6 tabs

Algorithms and analytical solutions for rapidly approximating long-term dispersion from line and area sources

Science.gov (United States)

Barrett, Steven R. H.; Britter, Rex E.

Predicting long-term mean pollutant concentrations in the vicinity of airports, roads and other industrial sources are frequently of concern in regulatory and public health contexts. Many emissions are represented geometrically as ground-level line or area sources. Well developed modelling tools such as AERMOD and ADMS are able to model dispersion from finite (i.e. non-point) sources with considerable accuracy, drawing upon an up-to-date understanding of boundary layer behaviour. Due to mathematical difficulties associated with line and area sources, computationally expensive numerical integration schemes have been developed. For example, some models decompose area sources into a large number of line sources orthogonal to the mean wind direction, for which an analytical (Gaussian) solution exists. Models also employ a time-series approach, which involves computing mean pollutant concentrations for every hour over one or more years of meteorological data. This can give rise to computer runtimes of several days for assessment of a site. While this may be acceptable for assessment of a single industrial complex, airport, etc., this level of computational cost precludes national or international policy assessments at the level of detail available with dispersion modelling. In this paper, we extend previous work [S.R.H. Barrett, R.E. Britter, 2008. Development of algorithms and approximations for rapid operational air quality modelling. Atmospheric Environment 42 (2008) 8105-8111] to line and area sources. We introduce approximations which allow for the development of new analytical solutions for long-term mean dispersion from line and area sources, based on hypergeometric functions. We describe how these solutions can be parameterized from a single point source run from an existing advanced dispersion model, thereby accounting for all processes modelled in the more costly algorithms. The parameterization method combined with the analytical solutions for long-term mean

Preliminary investigation of processes that affect source term identification

International Nuclear Information System (INIS)

Wickliff, D.S.; Solomon, D.K.; Farrow, N.D.

1991-09-01

Solid Waste Storage Area (SWSA) 5 is known to be a significant source of contaminants, especially tritium ( 3 H), to the White Oak Creek (WOC) watershed. For example, Solomon et al. (1991) estimated the total 3 H discharge in Melton Branch (most of which originates in SWSA 5) for the 1988 water year to be 1210 Ci. A critical issue for making decisions concerning remedial actions at SWSA 5 is knowing whether the annual contaminant discharge is increasing or decreasing. Because (1) the magnitude of the annual contaminant discharge is highly correlated to the amount of annual precipitation (Solomon et al., 1991) and (2) a significant lag may exist between the time of peak contaminant release from primary sources (i.e., waste trenches) and the time of peak discharge into streams, short-term stream monitoring by itself is not sufficient for predicting future contaminant discharges. In this study we use 3 H to examine the link between contaminant release from primary waste sources and contaminant discharge into streams. By understanding and quantifying subsurface transport processes, realistic predictions of future contaminant discharge, along with an evaluation of the effectiveness of remedial action alternatives, will be possible. The objectives of this study are (1) to characterize the subsurface movement of contaminants (primarily 3 H) with an emphasis on the effects of matrix diffusion; (2) to determine the relative strength of primary vs secondary sources; and (3) to establish a methodology capable of determining whether the 3 H discharge from SWSA 5 to streams is increasing or decreasing

Development of dose calculation program (DBADOSE) incorporating alternative source term due to design basis accident

International Nuclear Information System (INIS)

Bae, Young Jig; Nam, Ki Mun; Lee, Yu Jong; Chung, Chan Young

2003-01-01

Source terms presented in TID-14844 and Regulatory Guide 1.4 have been used for radiological analysis of design basis accidents for licensing existing pressurized water reactor (PWR). However, more realistic and physically-based source term based on results of study and experiments for about 30 years after the publication of TID-14844 was developed and presented in NUREG-1465 published by U.S NRC in 1995. In addition, ICRP has revised dose concepts and criteria through the publication of ICRP-9, 26, 60 and recommended effective dose concepts rather than critical organ concept since the publication of ICRP-26. Accordingly, multipurpose computer program called DBADOSE incorporating alternative source terms in NUREG-1465 and effective dose concepts in ICRP-60 was developed. Comparison of results of DBADOSE with those of POSTDBA and STARDOSE was performed and verified and no significant difference and inaccuracy were found. DBADOSE will be used to evaluate accidental doses for licensing application according to the domestic laws that are expected to be revised in the near future

Benchmarking the New RESRAD-OFFSITE Source Term Model with DUST-MS and GoldSim - 13377

Energy Technology Data Exchange (ETDEWEB)

Cheng, J.J.; Kamboj, S.; Gnanapragasam, E.; Yu, C. [Argonne National Laboratory, Argonne, IL 60439 (United States)

2013-07-01

RESRAD-OFFSITE is a computer code developed by Argonne National Laboratory under the sponsorship of U.S. Department of Energy (DOE) and U.S. Nuclear Regulatory Commission (NRC). It is designed on the basis of RESRAD (onsite) code, a computer code designated by DOE and NRC for evaluating soil-contaminated sites for compliance with human health protection requirements pertaining to license termination or environmental remediation. RESRAD-OFFSITE has enhanced capabilities of modeling radionuclide transport to offsite locations and calculating potential radiation exposure to offsite receptors. Recently, a new source term model was incorporated into RESRAD-OFFSITE to enhance its capability further. This new source term model allows simulation of radionuclide releases from different waste forms, in addition to the soil sources originally considered in RESRAD (onsite) and RESRAD-OFFSITE codes. With this new source term model, a variety of applications can be achieved by using RESRAD-OFFSITE, including but not limited to, assessing the performance of radioactive waste disposal facilities. This paper presents the comparison of radionuclide release rates calculated by the new source term model of RESRAD-OFFSITE versus those calculated by DUST-MS and GoldSim, respectively. The focus of comparison is on the release rates of radionuclides from the bottom of the contaminated zone that was assumed to contain radioactive source materials buried in soil. The transport of released contaminants outside of the primary contaminated zone is beyond the scope of this paper. Overall, the agreement between the RESRAD-OFFSITE results and the DUST-MS and GoldSim results is fairly good, with all three codes predicting identical or similar radionuclide release profiles over time. Numerical dispersion in the DUST-MS and GoldSim results was identified as potentially contributing to the disagreement in the release rates. In general, greater discrepancy in the release rates was found for short

Benchmarking the New RESRAD-OFFSITE Source Term Model with DUST-MS and GoldSim - 13377

International Nuclear Information System (INIS)

Cheng, J.J.; Kamboj, S.; Gnanapragasam, E.; Yu, C.

2013-01-01

RESRAD-OFFSITE is a computer code developed by Argonne National Laboratory under the sponsorship of U.S. Department of Energy (DOE) and U.S. Nuclear Regulatory Commission (NRC). It is designed on the basis of RESRAD (onsite) code, a computer code designated by DOE and NRC for evaluating soil-contaminated sites for compliance with human health protection requirements pertaining to license termination or environmental remediation. RESRAD-OFFSITE has enhanced capabilities of modeling radionuclide transport to offsite locations and calculating potential radiation exposure to offsite receptors. Recently, a new source term model was incorporated into RESRAD-OFFSITE to enhance its capability further. This new source term model allows simulation of radionuclide releases from different waste forms, in addition to the soil sources originally considered in RESRAD (onsite) and RESRAD-OFFSITE codes. With this new source term model, a variety of applications can be achieved by using RESRAD-OFFSITE, including but not limited to, assessing the performance of radioactive waste disposal facilities. This paper presents the comparison of radionuclide release rates calculated by the new source term model of RESRAD-OFFSITE versus those calculated by DUST-MS and GoldSim, respectively. The focus of comparison is on the release rates of radionuclides from the bottom of the contaminated zone that was assumed to contain radioactive source materials buried in soil. The transport of released contaminants outside of the primary contaminated zone is beyond the scope of this paper. Overall, the agreement between the RESRAD-OFFSITE results and the DUST-MS and GoldSim results is fairly good, with all three codes predicting identical or similar radionuclide release profiles over time. Numerical dispersion in the DUST-MS and GoldSim results was identified as potentially contributing to the disagreement in the release rates. In general, greater discrepancy in the release rates was found for short

Source Term Characteristics Analysis for Structural Components in PWR spent fuel assembly

Energy Technology Data Exchange (ETDEWEB)

Kook, Dong Hak; Choi, Heui Joo; Cho, Dong Keun [KAERI, Daejeon (Korea, Republic of)

2010-12-15

Source terms of metal waste comprising a spent fuel assembly are relatively important when the spent fuel is pyroprocessed, because cesium, strontium, and transuranics are not a concern any more in the aspect of source term of permanent disposal. In this study, characteristics of radiation source terms for each structural component in spent fuel assembly was analyzed by using ORIGEN-S with a assumption that 10 metric tons of uranium is pyroprocessed. At first, mass and volume for each structural component of the fuel assembly were calculated in detail. Activation cross section library was generated by using KENO-VI/ORIGEN-S module for top-end piece and bottom-end piece, because those are located at outer core under different neutron spectrum compared to that of inner core. As a result, values of radioactivity, decay heat, and hazard index were reveled to be 1.32x1015 Bequerels, 238 Watts, 4.32x109 m3 water, respectively, at 10 years after discharge. Those values correspond to 0.6 %, 1.1 %, 0.1 %, respectively, compared to that of spent fuel. Inconel 718 grid plate was shown to be the most important component in the all aspects of radioactivity, decay heat, and hazard index although the mass occupies only 1 % of the total. It was also shown that if the Inconel 718 grid plate is managed separately, the radioactivity and hazard index of metal waste could be decreased to 25{approx}50 % and 35{approx}40 %, respectively. As a whole, decay heat of metal waste was shown to be negligible in the aspect of disposal system design, while the radioactivity and hazard index are important

SOURCE TERM ESTIMATION BASED on PLANT STATUS and on GAMMA DOSE RATES Measured by an ON-line environmental Monitoring Network

International Nuclear Information System (INIS)

Stubna, M.; Bujan, A.; Duranova, T.

1997-01-01

A number of severe accident analyses for reactor unit with WWER-440 (213) has been performed in order to evaluate the source term and radiological consequences. As a tool for these analyses the WWER modified version of Source Term Code Package and Real Time Accident Release Consequences codes have been used. A set of emergency procedures - manuals for quick estimation of the source term and countermeasures introduction during early -pre-release phase of severe accident progression has been developed at Nuclear Power Plants Research Institute Trnava, Inc. These manuals are subdivided into three groups: 1.) evaluation of the barriers integrity, 2.) source term estimation and 3.) estimation of the distances for the countermeasures introduction. A methodology and computer module for interpretation of environmental data - source term assessment during post-release phase from on-line environmental network has been developed at Nuclear Power Plants Research Institute Trnava, Inc. The method is based on the conversion of measured dose rates to the source term,i.e. airborne radioactivity release rate, taking into account real meteorological data and location of the measure points. The bootstrap method for the estimation of the mean value of source term Q as integral value of the release and confidence interval of Q has been selected. The methodology of Q distribution into fission product groups according to code Real Time Accident Release Consequences needs is based on known plant status, i.e. on the results of pre calculated accident sequences. The paper describes the methodologies introduced above and the way of their application

Analysis of the source term in the Chernobyl-4 accident

International Nuclear Information System (INIS)

Alonso, A.; Lopez Montero, J.V.; Pinedo Garrido, P.

1990-01-01

The report presents the analysis of the Chernobyl accident and of the phenomena with major influence on the source term, including the chemical effects of materials dumped over the reactor, carried out by the Chair of Nuclear Technology at Madrid University under a contract with the CEC. It also includes the comparison of the ratio (Cs-137/Cs-134) between measurements performed by Soviet authorities and countries belonging to the Community and OECD area. Chapter II contains a summary of both isotope measurements (Cs-134 and Cs-137), and their ratios, in samples of air, water, soil and agricultural and animal products collected by the Soviets in their report presented in Vienna (1986). Chapter III reports on the inventories of cesium isotopes in the core, while Chapter IV analyses the transient, especially the fuel temperature reached, as a way to deduce the mechanisms which took place in the cesium escape. The cesium source term is analyzed in Chapter V. Normal conditions have been considered, as well as the transient and the post-accidental period, including the effects of deposited materials. The conclusion of this study is that Chernobyl accidental sequence is specific of the RBMK type of reactors, and that in the Western world, basic research on fuel behaviour for reactivity transients has already been carried out

Applying Satellite Data Sources in the Documentation and Landscape Modelling for Graeco-Roman Fortified Sites in the TŪR Abdin Area, Eastern Turkey

Science.gov (United States)

Silver, K.; Silver, M.; Törmä, M.; Okkonen, J.; Okkonen, T.

2017-08-01

In 2015-2016 the Finnish-Swedish Archaeological Project in Mesopotamia (FSAPM) initiated a pilot study of an unexplored area in the Tūr Abdin region in Northern Mesopotamia (present-day Mardin Province in southeastern Turkey). FSAPM is reliant on satellite image data sources for prospecting, identifying, recording, and mapping largely unknown archaeological sites as well as studying their landscapes in the region. The purpose is to record and document sites in this endangered area for saving its cultural heritage. The sites in question consist of fortified architectural remains in an ancient border zone between the Graeco-Roman/Byzantine world and Parthia/Persia. The location of the archaeological sites in the terrain and the visible archaeological remains, as well as their dimensions and sizes were determined from the ortorectified satellite images, which also provided coordinates. In addition, field documentation was carried out in situ with photographs and notes. The applicability of various satellite data sources for the archaeological documentation of the project was evaluated. Satellite photographs from three 1968 CORONA missions, i.e. the declassified US government satellite photograph archives were acquired. Furthermore, satellite images included a recent GeoEye-1 Satellite Sensor Image from 2010 with a resolution of 0.5 m. Its applicability for prospecting archaeological sites, studying the terrain and producing landscape models in 3D was confirmed. The GeoEye-1 revealed the ruins of a fortified town and a fortress for their documentation and study. Landscape models for the area of these sites were constructed fusing GeoEye-1 with EU-DEM (European Digital Elevation Model data using SRTM and ASTER GDEM data) in order to understand their locations in the terrain.

Dose assessments for Greifswald and Cadarache with new source terms from ITER NSSR-1

International Nuclear Information System (INIS)

Raskob, W.; Forschungszentrum Karlsruhe GmbH Technik und Umwelt; Hasemann, I.

1997-08-01

Probabilistic dose assessments for accidental atmospheric releases of various ITER source terms which contain tritium and/or activation products were performed for the sites of Greifswald, Germany, and Cadarache, France. No country specific rules were applied and the input parameters were adapted as far as possible to those used within former ITER studies to achieve a better comparability with site independent dose assessments performed in the frame of ITER. The calculations were based on source terms which, at the first time, contain a combination of tritium and activation products. This allowed a better judgement of the contribution of the individual fusion relevant materials to the total dose. The results were compared to site independent dose limits defined in the frame of ITER. Source terms for two different categories, representing 'extremely unlikely events' (CAT-IV) and 'hypothetical sequences' (CAT-V), were investigated. In no cases, the release scenarios of category CAT-IV exceeded the ITER limits. In addition, early doses from the hypothetical scenarios of type CAT-V were still below 50 mSv or 100 mSv, values which are commonly used as lower reference values for evacuation in many potential home countries of ITER. Only the banning of food products was found to be a potential countermeasure which may affect larger areas. (orig.) [de

Implementing the EuroFIR Document and Data Repositories as accessible resources of food composition information.

Science.gov (United States)

Unwin, Ian; Jansen-van der Vliet, Martine; Westenbrink, Susanne; Presser, Karl; Infanger, Esther; Porubska, Janka; Roe, Mark; Finglas, Paul

2016-02-15

The EuroFIR Document and Data Repositories are being developed as accessible collections of source documents, including grey literature, and the food composition data reported in them. These Repositories will contain source information available to food composition database compilers when selecting their nutritional data. The Document Repository was implemented as searchable bibliographic records in the Europe PubMed Central database, which links to the documents online. The Data Repository will contain original data from source documents in the Document Repository. Testing confirmed the FoodCASE food database management system as a suitable tool for the input, documentation and quality assessment of Data Repository information. Data management requirements for the input and documentation of reported analytical results were established, including record identification and method documentation specifications. Document access and data preparation using the Repositories will provide information resources for compilers, eliminating duplicated work and supporting unambiguous referencing of data contributing to their compiled data. Copyright © 2014 Elsevier Ltd. All rights reserved.

Source term calculations - Ringhals 2 PWR

International Nuclear Information System (INIS)

Johansson, L.L.

1998-02-01

This project was performed within the fifth and final phase of sub-project RAK-2.1 of the Nordic Co-operative Reactor Safety Program, NKS.RAK-2.1 has also included studies of reflooding of degraded core, recriticality and late phase melt progression. Earlier source term calculations for Swedish nuclear power plants are based on the integral code MAAP. A need was recognised to compare these calculations with calculations done with mechanistic codes. In the present work SCDAP/RELAP5 and CONTAIN were used. Only limited results could be obtained within the frame of RAK-2.1, since many problems were encountered using the SCDAP/RELAP5 code. The main obstacle was the extremely long execution times of the MOD3.1 version, but also some dubious fission product calculations. However, some interesting results were obtained for the studied sequence, a total loss of AC power. The report describes the modelling approach for SCDAP/RELAP5 and CONTAIN, and discusses results for the transient including the event of a surge line creep rupture. The study will probably be completed later, providing that an improved SCDAP/RELAP5 code version becomes available. (au) becomes available. (au)

Basic freight forwarding and transport
 documentation in freight forwarder’s work

Directory of Open Access Journals (Sweden)

Adam Salomon

2014-09-01

Full Text Available The purpose of the article is to present the basic documentation in international freight forwarder’s work, in particular, insurance documents and transport documents in various modes of transport. An additional goal is to identify sources of the paper, which can be used to properly completing the individual documents.

Basic repository source term and data sheet report: Lavender Canyon

International Nuclear Information System (INIS)

1988-01-01

This report is one of a series describing studies undertaken in support of the US Department of Energy Civilian Radioactive Waste Management (CRWM) Program. This study contains the derivation of values for environmental source terms and resources consumed for a CRWM repository. Estimates include heavy construction equipment; support equipment; shaft-sinking equipment; transportation equipment; and consumption of fuel, water, electricity, and natural gas. Data are presented for construction and operation at an assumed site in Lavender Canyon, Utah. 3 refs; 6 tabs

Fiscal year 1999 waste information requirements document

International Nuclear Information System (INIS)

Adams, M.R.

1998-01-01

The Waste Information Requirements Document (WIRD) has the following purposes: To describe the overall drivers that require characterization information and to document their source; To define how characterization is going to satisfy the drivers, close issues, and measure and report progress; and To describe deliverables and acceptance criteria for characterization. Characterization information is required to maintain regulatory compliance, perform operations and maintenance, resolve safety issues, and prepare for disposal of waste. Commitments addressing these requirements are derived from the Hanford Federal Facility Agreement and Consent Order, also known as the Tri-Party Agreement; the Recommendation 93-5 Implementation Plan (DOE-RL 1996a) to the Defense Nuclear Facilities Safety Board (DNFSB); and other requirement sources listed in Section 2.0. The Waste Information Requirements Document replaces the tank waste analysis plans and the tank characterization plan previously required by the Tri-Party Agreement, Milestone M-44-01 and M-44-02 series

Emergency preparedness source term development for the Office of Nuclear Material Safety and Safeguards-Licensed Facilities

International Nuclear Information System (INIS)

Sutter, S.L.; Mishima, J.; Ballinger, M.Y.; Lindsey, C.G.

1984-08-01

In order to establish requirements for emergency preparedness plans at facilities licensed by the Office of Nuclear Materials Safety and Safeguards, the Nuclear Regulatory Commission (NRC) needs to develop source terms (the amount of material made airborne) in accidents. These source terms are used to estimate the potential public doses from the events, which, in turn, will be used to judge whether emergency preparedness plans are needed for a particular type of facility. Pacific Northwest Laboratory is providing the NRC with source terms by developing several accident scenarios for eleven types of fuel cycle and by-product operations. Several scenarios are developed for each operation, leading to the identification of the maximum release considered for emergency preparedness planning (MREPP) scenario. The MREPP scenarios postulated were of three types: fire, tornado, and criticality. Fire was significant at oxide fuel fabrication, UF 6 production, radiopharmaceutical manufacturing, radiopharmacy, sealed source manufacturing, waste warehousing, and university research and development facilities. Tornadoes were MREPP events for uranium mills and plutonium contaminated facilities, and criticalities were significant at nonoxide fuel fabrication and nuclear research and development facilities. Techniques for adjusting the MREPP release to different facilities are also described

Integration of clinical research documentation in electronic health records.

Science.gov (United States)

Broach, Debra

2015-04-01

Clinical trials of investigational drugs and devices are often conducted within healthcare facilities concurrently with clinical care. With implementation of electronic health records, new communication methods are required to notify nonresearch clinicians of research participation. This article reviews clinical research source documentation, the electronic health record and the medical record, areas in which the research record and electronic health record overlap, and implications for the research nurse coordinator in documentation of the care of the patient/subject. Incorporation of clinical research documentation in the electronic health record will lead to a more complete patient/subject medical record in compliance with both research and medical records regulations. A literature search provided little information about the inclusion of clinical research documentation within the electronic health record. Although regulations and guidelines define both source documentation and the medical record, integration of research documentation in the electronic health record is not clearly defined. At minimum, the signed informed consent(s), investigational drug or device usage, and research team contact information should be documented within the electronic health record. Institutional policies should define a standardized process for this integration in the absence federal guidance. Nurses coordinating clinical trials are in an ideal position to define this integration.

Environmental radiation safety: source term modification by soil aerosols. Interim report

International Nuclear Information System (INIS)

Moss, O.R.; Allen, M.D.; Rossignol, E.J.; Cannon, W.C.

1980-08-01

The goal of this project is to provide information useful in estimating hazards related to the use of a pure refractory oxide of 238 Pu as a power source in some of the space vehicles to be launched during the next few years. Although the sources are designed and built to withstand re-entry into the earth's atmosphere, and to impact with the earth's surface without releasing any plutonium, the possibility that such an event might produce aerosols composed of soil and 238 PuO 2 cannot be absolutely excluded. This report presents the results of our most recent efforts to measure the degree to which the plutonium aerosol source term might be modified in a terrestrial environment. The five experiments described represent our best effort to use the original experimental design to study the change in the size distribution and concentration of a 238 PuO 2 aerosol due to coagulation with an aerosol of clay or sandy loam soil

Standardization of iridium-192 coiled source in terms of air kerma output

Energy Technology Data Exchange (ETDEWEB)

Shanta, A; Unnikrishnan, K; Tripathi, U B; Kannan, A; Iyer, P S [Bhabha Atomic Research Centre, Bombay (India)

1996-08-01

ICRU (1985) recommended that the output of gamma ray brachytherapy sources should be specified in terms of reference air kerma rate, defined as the kerma rate to air in air at a reference distance of 1 meter, perpendicular to the long axis of the source, corrected for air attenuation and scattering. As these measurements are difficult to carry out in the routine clinical use, it is the common practice to calibrate the re-entrant ionization chamber with respect to open air measurements and use the re-entrant chamber for routine measurements. This paper reports on the measurements carried out to correlate the nominal activity and air kerma rate of {sup 192}Ir wire sources supplied by the Board of Radiation and Isotope Technology, Department of Atomic Energy. (author). 3 refs, 1 tab.

Standardization of iridium-192 coiled source in terms of air kerma output

International Nuclear Information System (INIS)

Shanta, A.; Unnikrishnan, K.; Tripathi, U.B.; Kannan, A.; Iyer, P.S.

1996-01-01

ICRU (1985) recommended that the output of gamma ray brachytherapy sources should be specified in terms of reference air kerma rate, defined as the kerma rate to air in air at a reference distance of 1 meter, perpendicular to the long axis of the source, corrected for air attenuation and scattering. As these measurements are difficult to carry out in the routine clinical use, it is the common practice to calibrate the re-entrant ionization chamber with respect to open air measurements and use the re-entrant chamber for routine measurements. This paper reports on the measurements carried out to correlate the nominal activity and air kerma rate of 192 Ir wire sources supplied by the Board of Radiation and Isotope Technology, Department of Atomic Energy. (author). 3 refs, 1 tab

Long-term program up to fiscal 1993 of electric power source development

International Nuclear Information System (INIS)

Kawakami, Shin-ichi

1984-01-01

The long-term, ten years, program up to fiscal 1993 of electric power source development, determined by the Government aims at stable power supply and the expansion of utilization of petroleum-substitute energy. The annual growth in the gross national product (GNP) during the ten years was taken as about 4 %. So, the total electric power demand in fiscal 1993 is scheduled to be 731,000 million kwh, about 34 % up from 547,000 million kwh in fiscal 1983. The structure of electric power sources at the end of fiscal 1993 will be hydraulic 19.7 %, thermal 58.3 %, and nuclear 21.9 %. The development of electric power sources to be initiated in fiscal 1984 is hydraulic 500 MW, thermal 2,000 MW, and nuclear 6,000 MW. (Mori, K.)

Overview of Historical Earthquake Document Database in Japan and Future Development

Science.gov (United States)

Nishiyama, A.; Satake, K.

2014-12-01

In Japan, damage and disasters from historical large earthquakes have been documented and preserved. Compilation of historical earthquake documents started in the early 20th century and 33 volumes of historical document source books (about 27,000 pages) have been published. However, these source books are not effectively utilized for researchers due to a contamination of low-reliability historical records and a difficulty for keyword searching by characters and dates. To overcome these problems and to promote historical earthquake studies in Japan, construction of text database started in the 21 century. As for historical earthquakes from the beginning of the 7th century to the early 17th century, "Online Database of Historical Documents in Japanese Earthquakes and Eruptions in the Ancient and Medieval Ages" (Ishibashi, 2009) has been already constructed. They investigated the source books or original texts of historical literature, emended the descriptions, and assigned the reliability of each historical document on the basis of written age. Another database compiled the historical documents for seven damaging earthquakes occurred along the Sea of Japan coast in Honshu, central Japan in the Edo period (from the beginning of the 17th century to the middle of the 19th century) and constructed text database and seismic intensity data base. These are now publicized on the web (written only in Japanese). However, only about 9 % of the earthquake source books have been digitized so far. Therefore, we plan to digitize all of the remaining historical documents by the research-program which started in 2014. The specification of the data base will be similar for previous ones. We also plan to combine this database with liquefaction traces database, which will be constructed by other research program, by adding the location information described in historical documents. Constructed database would be utilized to estimate the distributions of seismic intensities and tsunami

Audit of Orthopaedic Surgical Documentation

Directory of Open Access Journals (Sweden)

Fionn Coughlan

2015-01-01

Full Text Available Introduction. The Royal College of Surgeons in England published guidelines in 2008 outlining the information that should be documented at each surgery. St. James’s Hospital uses a standard operation sheet for all surgical procedures and these were examined to assess documentation standards. Objectives. To retrospectively audit the hand written orthopaedic operative notes according to established guidelines. Methods. A total of 63 operation notes over seven months were audited in terms of date and time of surgery, surgeon, procedure, elective or emergency indication, operative diagnosis, incision details, signature, closure details, tourniquet time, postop instructions, complications, prosthesis, and serial numbers. Results. A consultant performed 71.4% of procedures; however, 85.7% of the operative notes were written by the registrar. The date and time of surgery, name of surgeon, procedure name, and signature were documented in all cases. The operative diagnosis and postoperative instructions were frequently not documented in the designated location. Incision details were included in 81.7% and prosthesis details in only 30% while the tourniquet time was not documented in any. Conclusion. Completion and documentation of operative procedures were excellent in some areas; improvement is needed in documenting tourniquet time, prosthesis and incision details, and the location of operative diagnosis and postoperative instructions.

The Phebus Fission Product and Source Term International Programmes

International Nuclear Information System (INIS)

Clement, B.; Zeyen, R.

2005-01-01

The international Phebus FP programme, initiated in 1988 is one of the major research programmes on light water reactors severe accidents. After a short description of the facility and of the test matrix, the main outcomes and results of the first four integral tests are provided and analysed. Several results were unexpected and some are of importance for safety analyses, particularly concerning fuel degradation, cladding oxidation, chemical form of some fission products, especially iodine, effect of control rod materials on degradation and chemistry, iodine behaviour in the containment. Prediction capabilities of calculation tools have largely been improved as a result of this research effort. However, significant uncertainties remain for a number of phenomena, requiring detailed physical analysis and implementation of improved models in codes, sustained by a number of separate-effect experiments. This is the subject of the new Source Term programme for a better understanding of the phenomenology on important safety issues, in accordance with priorities defined in the EURSAFE project of the 5 th European framework programme aiming at reducing the uncertainties on Source Term analyses. It covers iodine chemistry, impact of boron carbide control rods degradation and oxidation, air ingress situations and fission product release from fuel. Regarding the interpretation of Phebus, an international co-operation has been established since over ten years, particularly helpful for the improvement and common understanding of severe accident phenomena. Few months ago, the Phebus community was happy to welcome representatives of a large number of organisations from the following new European countries: the Czech republic, Hungary, Lithuania, Slovakia, Slovenia and also from Bulgaria and Romania. (author)

Radioactivity source terms for underground engineering application

Energy Technology Data Exchange (ETDEWEB)

Tewes, H A [Lawrence Radiation Laboratory, Livermore, CA (United States)

1969-07-01

The constraints on nuclide production are usually very similar in any underground engineering application of nuclear explosives. However, in some applications the end product could be contaminated unless the proper nuclear device is used. This fact can be illustrated from two underground engineering experiments-Gasbuggy and Sloop. In the Gasbuggy experiment, appreciable tritium has been shown to be present in the gas currently being produced. However, in future gas stimulation applications (as distinct from experiments), a minimum production of tritium by the explosive is desirable since product contamination by this nuclide may place severe limitations on the use of the tritiated gas. In Sloop, where production of copper is the goal of the experiment, product contamination would not be caused by tritium but could result from other nuclides: Thus, gas stimulation could require the use of fission explosives while the lower cost per kiloton of thermonuclear explosives could make them attractive for ore-crushing applications. Because of this consideration, radionuclide production calculations must be made for both fission and for thermonuclear explosives in the underground environment. Such activation calculations materials of construction are performed in a manner similar to that described in another paper, but radionuclide production in the environment must be computed using both fission neutron and 14-MeV neutron sources in order to treat the 'source term' problem realistically. In making such computations, parameter studies including the effects of environmental temperature, neutron shielding, and rock types have been carried out. Results indicate the importance of carefully evaluating the radionuclide production for each individual underground engineering application. (author)

Radioactivity source terms for underground engineering application

International Nuclear Information System (INIS)

Tewes, H.A.

1969-01-01

The constraints on nuclide production are usually very similar in any underground engineering application of nuclear explosives. However, in some applications the end product could be contaminated unless the proper nuclear device is used. This fact can be illustrated from two underground engineering experiments-Gasbuggy and Sloop. In the Gasbuggy experiment, appreciable tritium has been shown to be present in the gas currently being produced. However, in future gas stimulation applications (as distinct from experiments), a minimum production of tritium by the explosive is desirable since product contamination by this nuclide may place severe limitations on the use of the tritiated gas. In Sloop, where production of copper is the goal of the experiment, product contamination would not be caused by tritium but could result from other nuclides: Thus, gas stimulation could require the use of fission explosives while the lower cost per kiloton of thermonuclear explosives could make them attractive for ore-crushing applications. Because of this consideration, radionuclide production calculations must be made for both fission and for thermonuclear explosives in the underground environment. Such activation calculations materials of construction are performed in a manner similar to that described in another paper, but radionuclide production in the environment must be computed using both fission neutron and 14-MeV neutron sources in order to treat the 'source term' problem realistically. In making such computations, parameter studies including the effects of environmental temperature, neutron shielding, and rock types have been carried out. Results indicate the importance of carefully evaluating the radionuclide production for each individual underground engineering application. (author)

Finite volume schemes with equilibrium type discretization of source terms for scalar conservation laws

International Nuclear Information System (INIS)

Botchorishvili, Ramaz; Pironneau, Olivier

2003-01-01

We develop here a new class of finite volume schemes on unstructured meshes for scalar conservation laws with stiff source terms. The schemes are of equilibrium type, hence with uniform bounds on approximate solutions, valid in cell entropy inequalities and exact for some equilibrium states. Convergence is investigated in the framework of kinetic schemes. Numerical tests show high computational efficiency and a significant advantage over standard cell centered discretization of source terms. Equilibrium type schemes produce accurate results even on test problems for which the standard approach fails. For some numerical tests they exhibit exponential type convergence rate. In two of our numerical tests an equilibrium type scheme with 441 nodes on a triangular mesh is more accurate than a standard scheme with 5000 2 grid points

COMPASS: A source term code for investigating capillary barrier performance

International Nuclear Information System (INIS)

Zhou, Wei; Apted, J.J.

1996-01-01

A computer code COMPASS based on compartment model approach is developed to calculate the near-field source term of the High-Level-Waste repository under unsaturated conditions. COMPASS is applied to evaluate the expected performance of Richard's (capillary) barriers as backfills to divert infiltrating groundwater at Yucca Mountain. Comparing the release rates of four typical nuclides with and without the Richard's barrier, it is shown that the Richard's barrier significantly decreases the peak release rates from the Engineered-Barrier-System (EBS) into the host rock

Sources for charged particles

International Nuclear Information System (INIS)

Arianer, J.

1997-01-01

This document is a basic course on charged particle sources for post-graduate students and thematic schools on large facilities and accelerator physics. A simple but precise description of the creation and the emission of charged particles is presented. This course relies on every year upgraded reference documents. Following relevant topics are considered: electronic emission processes, technological and practical considerations on electron guns, positron sources, production of neutral atoms, ionization, plasma and discharge, different types of positive and negative ion sources, polarized particle sources, materials for the construction of ion sources, low energy beam production and transport. (N.T.)

On the application of subcell resolution to conservation laws with stiff source terms

International Nuclear Information System (INIS)

Chang, S.

1989-11-01

LeVeque and Yee recently investigated a one-dimensional scalar conservation law with stiff source terms modeling the reacting flow problems and discovered that for the very stiff case most of the current finite difference methods developed for non-reacting flows would produce wrong solutions when there is a propagating discontinuity. A numerical scheme, essentially nonoscillatory/subcell resolution - characteristic direction (ENO/SRCD), is proposed for solving conservation laws with stiff source terms. This scheme is a modification of Harten's ENO scheme with subcell resolution, ENO/SR. The locations of the discontinuities and the characteristic directions are essential in the design. Strang's time-splitting method is used and time evolutions are done by advancing along the characteristics. Numerical experiment using this scheme shows excellent results on the model problem of LeVeque and Yee. Comparisons of the results of ENO, ENO/SR, and ENO/SRCD are also presented

A functional magnetic resonance imaging investigation of short-term source and item memory for negative pictures.

Science.gov (United States)

Mitchell, Karen J; Mather, Mara; Johnson, Marcia K; Raye, Carol L; Greene, Erich J

2006-10-02

We investigated the hypothesis that arousal recruits attention to item information, thereby disrupting working memory processes that help bind items to context. Using functional magnetic resonance imaging, we compared brain activity when participants remembered negative or neutral picture-location conjunctions (source memory) versus pictures only. Behaviorally, negative trials showed disruption of short-term source, but not picture, memory; long-term picture recognition memory was better for negative than for neutral pictures. Activity in areas involved in working memory and feature integration (precentral gyrus and its intersect with superior temporal gyrus) was attenuated on negative compared with neutral source trials relative to picture-only trials. Visual processing areas (middle occipital and lingual gyri) showed greater activity for negative than for neutral trials, especially on picture-only trials.

2016 Expert consensus document on prevention, diagnosis and treatment of short-term peripheral venous catheter-related infections in adults

Directory of Open Access Journals (Sweden)

Josep A. Capdevila

2016-07-01

Full Text Available The use of endovascular catheters is a routine practice in secondary and tertiary care level hospitals. The short-term use of peripheral catheters has been found to be associated with the risk of nosocomial bacteraemia, resulting in morbidity and mortality. Staphylococcus aureus is mostly associated with peripheral catheter insertion. This Consensus Document has been prepared by a panel of experts of the Spanish Society of Cardiovascular Infections, in cooperation with experts from the Spanish Society of Internal Medicine, Spanish Society of Chemotherapy, and the Spanish Society of Thoracic-Cardiovascular Surgery, and aims to define and establish guidelines for the management of short duration peripheral vascular catheters. The document addresses the indications for insertion, catheter maintenance, registering, diagnosis and treatment of infection, indications for removal, as well as placing an emphasis on continuous education as a drive toward quality. Implementation of these guidelines will allow uniformity in use, thus minimizing the risk of infections and their complications.

Development of quality assurance programme for prescribed ionizing radiation source testing. Recommendations

International Nuclear Information System (INIS)

1999-01-01

The document gives guidance to those applying for licence to perform ionizing radiation source acceptance tests and long-term stability tests and provides information which should be known when introducing quality assurance systems in compliance with legislative requirements. It is envisaged that this document ('Recommendations') will form a basis for final Safety Guides to be issued by the State Office for Nuclear Safety, the Czech nuclear regulatory authority. The setup of the publication is as follows. Part I gives a glossary of basic terms in quality systems. Part 2 explains quality system principles, paying special attention to radiation safety issues, and describes the structure and scope of quality system documentation. Part 3 explains the individual elements of the quality system and gives practical examples. Part 4 deals with the quality assurance programme; using instructions and practical examples, this part shows how the quality system elements should be applied to long-time stability testing and acceptance testing. A model structure of 2nd degree documentation (guidelines) and a model testing protocol are given in annexes. (P.A.)

Quantification of uncertainties in source term estimates for a BWR with Mark I containment

International Nuclear Information System (INIS)

Khatib-Rahbar, M.; Cazzoli, E.; Davis, R.; Ishigami, T.; Lee, M.; Nourbakhsh, H.; Schmidt, E.; Unwin, S.

1988-01-01

A methodology for quantification and uncertainty analysis of source terms for severe accident in light water reactors (QUASAR) has been developed. The objectives of the QUASAR program are (1) to develop a framework for performing an uncertainty evaluation of the input parameters of the phenomenological models used in the Source Term Code Package (STCP), and (2) to quantify the uncertainties in certain phenomenological aspects of source terms (that are not modeled by STCP) using state-of-the-art methods. The QUASAR methodology consists of (1) screening sensitivity analysis, where the most sensitive input variables are selected for detailed uncertainty analysis, (2) uncertainty analysis, where probability density functions (PDFs) are established for the parameters identified by the screening stage and propagated through the codes to obtain PDFs for the outputs (i.e., release fractions to the environment), and (3) distribution sensitivity analysis, which is performed to determine the sensitivity of the output PDFs to the input PDFs. In this paper attention is limited to a single accident progression sequence, namely; a station blackout accident in a BWR with a Mark I containment buildings. Identified as an important accident in the draft NUREG-1150 a station blackout involves loss of both off-site power and DC power resulting in failure of the diesels to start and in the unavailability of the high pressure injection and core isolation coding systems

TWRS technical baseline database manager definition document

International Nuclear Information System (INIS)

Acree, C.D.

1997-01-01

This document serves as a guide for using the TWRS Technical Baseline Database Management Systems Engineering (SE) support tool in performing SE activities for the Tank Waste Remediation System (TWRS). This document will provide a consistent interpretation of the relationships between the TWRS Technical Baseline Database Management software and the present TWRS SE practices. The Database Manager currently utilized is the RDD-1000 System manufactured by the Ascent Logic Corporation. In other documents, the term RDD-1000 may be used interchangeably with TWRS Technical Baseline Database Manager

Semantic Annotation of Unstructured Documents Using Concepts Similarity

Directory of Open Access Journals (Sweden)

Fernando Pech

2017-01-01

Full Text Available There is a large amount of information in the form of unstructured documents which pose challenges in the information storage, search, and retrieval. This situation has given rise to several information search approaches. Some proposals take into account the contextual meaning of the terms specified in the query. Semantic annotation technique can help to retrieve and extract information in unstructured documents. We propose a semantic annotation strategy for unstructured documents as part of a semantic search engine. In this proposal, ontologies are used to determine the context of the entities specified in the query. Our strategy for extracting the context is focused on concepts similarity. Each relevant term of the document is associated with an instance in the ontology. The similarity between each of the explicit relationships is measured through the combination of two types of associations: the association between each pair of concepts and the calculation of the weight of the relationships.

PHENOstruct: Prediction of human phenotype ontology terms using heterogeneous data sources.

Science.gov (United States)

Kahanda, Indika; Funk, Christopher; Verspoor, Karin; Ben-Hur, Asa

2015-01-01

The human phenotype ontology (HPO) was recently developed as a standardized vocabulary for describing the phenotype abnormalities associated with human diseases. At present, only a small fraction of human protein coding genes have HPO annotations. But, researchers believe that a large portion of currently unannotated genes are related to disease phenotypes. Therefore, it is important to predict gene-HPO term associations using accurate computational methods. In this work we demonstrate the performance advantage of the structured SVM approach which was shown to be highly effective for Gene Ontology term prediction in comparison to several baseline methods. Furthermore, we highlight a collection of informative data sources suitable for the problem of predicting gene-HPO associations, including large scale literature mining data.

Radioiodine source term and its potential impact on the use of potassium iodide

International Nuclear Information System (INIS)

Malinauskas, A.P.

1982-01-01

Information is presented concerning chemical forms of fission product iodine in the primary circuit; chemical forms of fission product iodine in the containment building; summary of iodine chemistry in light water reactor accidents; and impact of the radiodine source term on the potassium iodide issue

APPLYING SATELLITE DATA SOURCES IN THE DOCUMENTATION AND LANDSCAPE MODELLING FOR GRAECO-ROMAN/BYZANTINE FORTIFIED SITES IN THE TŪR ABDIN AREA, EASTERN TURKEY

Directory of Open Access Journals (Sweden)

K. Silver

2017-08-01

Full Text Available In 2015-2016 the Finnish-Swedish Archaeological Project in Mesopotamia (FSAPM initiated a pilot study of an unexplored area in the Tūr Abdin region in Northern Mesopotamia (present-day Mardin Province in southeastern Turkey. FSAPM is reliant on satellite image data sources for prospecting, identifying, recording, and mapping largely unknown archaeological sites as well as studying their landscapes in the region. The purpose is to record and document sites in this endangered area for saving its cultural heritage. The sites in question consist of fortified architectural remains in an ancient border zone between the Graeco-Roman/Byzantine world and Parthia/Persia. The location of the archaeological sites in the terrain and the visible archaeological remains, as well as their dimensions and sizes were determined from the ortorectified satellite images, which also provided coordinates. In addition, field documentation was carried out in situ with photographs and notes. The applicability of various satellite data sources for the archaeological documentation of the project was evaluated. Satellite photographs from three 1968 CORONA missions, i.e. the declassified US government satellite photograph archives were acquired. Furthermore, satellite images included a recent GeoEye-1 Satellite Sensor Image from 2010 with a resolution of 0.5 m. Its applicability for prospecting archaeological sites, studying the terrain and producing landscape models in 3D was confirmed. The GeoEye-1 revealed the ruins of a fortified town and a fortress for their documentation and study. Landscape models for the area of these sites were constructed fusing GeoEye-1 with EU-DEM (European Digital Elevation Model data using SRTM and ASTER GDEM data in order to understand their locations in the terrain.

Chandra Source Catalog: User Interface

Science.gov (United States)

Bonaventura, Nina; Evans, Ian N.; Rots, Arnold H.; Tibbetts, Michael S.; van Stone, David W.; Zografou, Panagoula; Primini, Francis A.; Glotfelty, Kenny J.; Anderson, Craig S.; Chen, Judy C.; Davis, John E.; Doe, Stephen M.; Evans, Janet D.; Fabbiano, Giuseppina; Galle, Elizabeth C.; Gibbs, Danny G., II; Grier, John D.; Hain, Roger; Hall, Diane M.; Harbo, Peter N.; He, Helen; Houck, John C.; Karovska, Margarita; Kashyap, Vinay L.; Lauer, Jennifer; McCollough, Michael L.; McDowell, Jonathan C.; Miller, Joseph B.; Mitschang, Arik W.; Morgan, Douglas L.; Mossman, Amy E.; Nichols, Joy S.; Nowak, Michael A.; Plummer, David A.; Refsdal, Brian L.; Siemiginowska, Aneta L.; Sundheim, Beth A.; Winkelman, Sherry L.

2009-09-01

The Chandra Source Catalog (CSC) is intended to be the definitive catalog of all X-ray sources detected by Chandra. For each source, the CSC provides positions and multi-band fluxes, as well as derived spatial, spectral, and temporal source properties. Full-field and source region data products are also available, including images, photon event lists, light curves, and spectra. The Chandra X-ray Center CSC website (http://cxc.harvard.edu/csc/) is the place to visit for high-level descriptions of each source property and data product included in the catalog, along with other useful information, such as step-by-step catalog tutorials, answers to FAQs, and a thorough summary of the catalog statistical characterization. Eight categories of detailed catalog documents may be accessed from the navigation bar on most of the 50+ CSC pages; these categories are: About the Catalog, Creating the Catalog, Using the Catalog, Catalog Columns, Column Descriptions, Documents, Conferences, and Useful Links. There are also prominent links to CSCview, the CSC data access GUI, and related help documentation, as well as a tutorial for using the new CSC/Google Earth interface. Catalog source properties are presented in seven scientific categories, within two table views: the Master Source and Source Observations tables. Each X-ray source has one ``master source'' entry and one or more ``source observation'' entries, the details of which are documented on the CSC ``Catalog Columns'' pages. The master source properties represent the best estimates of the properties of a source; these are extensively described on the following pages of the website: Position and Position Errors, Source Flags, Source Extent and Errors, Source Fluxes, Source Significance, Spectral Properties, and Source Variability. The eight tutorials (``threads'') available on the website serve as a collective guide for accessing, understanding, and manipulating the source properties and data products provided by the catalog.

The development of a realistic source term for sodium-cooled fast reactors : assessment of current status and future needs.

Energy Technology Data Exchange (ETDEWEB)

LaChance, Jeffrey L.; Phillips, Jesse; Parma, Edward J., Jr.; Olivier, Tara Jean; Middleton, Bobby D.

2011-06-01

Sodium-cooled fast reactors (SFRs) continue to be proposed and designed throughout the United States and the world. Although the number of SFRs actually operating has declined substantially since the 1980s, a significant interest in advancing these types of reactor systems remains. Of the many issues associated with the development and deployment of SFRs, one of high regulatory importance is the source term to be used in the siting of the reactor. A substantial amount of modeling and experimental work has been performed over the past four decades on accident analysis, sodium coolant behavior, and radionuclide release for SFRs. The objective of this report is to aid in determining the gaps and issues related to the development of a realistic, mechanistically derived source term for SFRs. This report will allow the reader to become familiar with the severe accident source term concept and gain a broad understanding of the current status of the models and experimental work. Further, this report will allow insight into future work, in terms of both model development and experimental validation, which is necessary in order to develop a realistic source term for SFRs.

Inverse modeling of the Chernobyl source term using atmospheric concentration and deposition measurements

Science.gov (United States)

Evangeliou, Nikolaos; Hamburger, Thomas; Cozic, Anne; Balkanski, Yves; Stohl, Andreas

2017-07-01

This paper describes the results of an inverse modeling study for the determination of the source term of the radionuclides 134Cs, 137Cs and 131I released after the Chernobyl accident. The accident occurred on 26 April 1986 in the Former Soviet Union and released about 1019 Bq of radioactive materials that were transported as far away as the USA and Japan. Thereafter, several attempts to assess the magnitude of the emissions were made that were based on the knowledge of the core inventory and the levels of the spent fuel. More recently, when modeling tools were further developed, inverse modeling techniques were applied to the Chernobyl case for source term quantification. However, because radioactivity is a sensitive topic for the public and attracts a lot of attention, high-quality measurements, which are essential for inverse modeling, were not made available except for a few sparse activity concentration measurements far from the source and far from the main direction of the radioactive fallout. For the first time, we apply Bayesian inversion of the Chernobyl source term using not only activity concentrations but also deposition measurements from the most recent public data set. These observations refer to a data rescue attempt that started more than 10 years ago, with a final goal to provide available measurements to anyone interested. In regards to our inverse modeling results, emissions of 134Cs were estimated to be 80 PBq or 30-50 % higher than what was previously published. From the released amount of 134Cs, about 70 PBq were deposited all over Europe. Similar to 134Cs, emissions of 137Cs were estimated as 86 PBq, on the same order as previously reported results. Finally, 131I emissions of 1365 PBq were found, which are about 10 % less than the prior total releases. The inversion pushes the injection heights of the three radionuclides to higher altitudes (up to about 3 km) than previously assumed (≈ 2.2 km) in order to better match both concentration

Inverse modeling of the Chernobyl source term using atmospheric concentration and deposition measurements

Directory of Open Access Journals (Sweden)

N. Evangeliou

2017-07-01

Full Text Available This paper describes the results of an inverse modeling study for the determination of the source term of the radionuclides 134Cs, 137Cs and 131I released after the Chernobyl accident. The accident occurred on 26 April 1986 in the Former Soviet Union and released about 1019 Bq of radioactive materials that were transported as far away as the USA and Japan. Thereafter, several attempts to assess the magnitude of the emissions were made that were based on the knowledge of the core inventory and the levels of the spent fuel. More recently, when modeling tools were further developed, inverse modeling techniques were applied to the Chernobyl case for source term quantification. However, because radioactivity is a sensitive topic for the public and attracts a lot of attention, high-quality measurements, which are essential for inverse modeling, were not made available except for a few sparse activity concentration measurements far from the source and far from the main direction of the radioactive fallout. For the first time, we apply Bayesian inversion of the Chernobyl source term using not only activity concentrations but also deposition measurements from the most recent public data set. These observations refer to a data rescue attempt that started more than 10 years ago, with a final goal to provide available measurements to anyone interested. In regards to our inverse modeling results, emissions of 134Cs were estimated to be 80 PBq or 30–50 % higher than what was previously published. From the released amount of 134Cs, about 70 PBq were deposited all over Europe. Similar to 134Cs, emissions of 137Cs were estimated as 86 PBq, on the same order as previously reported results. Finally, 131I emissions of 1365 PBq were found, which are about 10 % less than the prior total releases. The inversion pushes the injection heights of the three radionuclides to higher altitudes (up to about 3 km than previously assumed (≈ 2.2 km in order

Document retrieval on repetitive string collections.

Science.gov (United States)

Gagie, Travis; Hartikainen, Aleksi; Karhu, Kalle; Kärkkäinen, Juha; Navarro, Gonzalo; Puglisi, Simon J; Sirén, Jouni

2017-01-01

Most of the fastest-growing string collections today are repetitive, that is, most of the constituent documents are similar to many others. As these collections keep growing, a key approach to handling them is to exploit their repetitiveness, which can reduce their space usage by orders of magnitude. We study the problem of indexing repetitive string collections in order to perform efficient document retrieval operations on them. Document retrieval problems are routinely solved by search engines on large natural language collections, but the techniques are less developed on generic string collections. The case of repetitive string collections is even less understood, and there are very few existing solutions. We develop two novel ideas, interleaved LCPs and precomputed document lists , that yield highly compressed indexes solving the problem of document listing (find all the documents where a string appears), top- k document retrieval (find the k documents where a string appears most often), and document counting (count the number of documents where a string appears). We also show that a classical data structure supporting the latter query becomes highly compressible on repetitive data. Finally, we show how the tools we developed can be combined to solve ranked conjunctive and disjunctive multi-term queries under the simple [Formula: see text] model of relevance. We thoroughly evaluate the resulting techniques in various real-life repetitiveness scenarios, and recommend the best choices for each case.

A well-balanced scheme for Ten-Moment Gaussian closure equations with source term

Science.gov (United States)

Meena, Asha Kumari; Kumar, Harish

2018-02-01

In this article, we consider the Ten-Moment equations with source term, which occurs in many applications related to plasma flows. We present a well-balanced second-order finite volume scheme. The scheme is well-balanced for general equation of state, provided we can write the hydrostatic solution as a function of the space variables. This is achieved by combining hydrostatic reconstruction with contact preserving, consistent numerical flux, and appropriate source discretization. Several numerical experiments are presented to demonstrate the well-balanced property and resulting accuracy of the proposed scheme.

Rating of transport and radiation source events. Draft additional guidance for the INES national officers for pilot use and feedback; Echelle de classement des incidents de radioprotection: document d'application du systeme international propose par l'AIEA pour les sources radioactives et les transports

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-09-15

The International Nuclear Event Scale (INES) is a means for promptly communicating to the public in consistent terms the safety significance of any reported event associated with radioactive material and/or radiation and to any event occurring during the transport of radioactive material. As described in the 2001 Edition of the INES User.s Manual, events are classified on the scale at seven levels: the upper levels (4-7) are termed accidents. and the lower levels (1-3) incidents. Events which have no safety significance are classified below scale at Level 0 and termed deviations. An overview of the principles for the rating under INES together with flow charts summarizing the rating process is provided in Appendix I. The 2001 Edition of the INES User.s Manual provides some guidance for the rating of transport and radiation source events. At the technical meeting held in 2002 the INES National Officers requested the IAEA/NEA Secretariat to prepare additional guidance. Progress was reported at the Technical Meeting of the INES National Officers in March 2004 where preparation of this draft additional guidance was requested for pilot use. This note provides additional guidance on the rating of transport and radiation source events. It is for pilot use and feedback and is broadly consistent with the INES User.s Manual. It provides more detailed information and an expanded approach for the rating based on actual exposure of workers and members of the public. It is designed to be used as a self-standing document with limited need for reference to the INES User Manual. (author)

Air pollutant emission rates for sources at the Deaf Smith County repository site

International Nuclear Information System (INIS)

1985-11-01

This document summarizes the air-quality source terms used for the Deaf Smith County, Texas environmental assessment report and explains their derivation. The engineering data supporting these source terms appear as appendixes to this report and include summary equipment lists for the repository and detailed equipment lists for the exploratory shaft. Although substantial work has been performed in establishing the current repository design, a greater effort will be required for the final design. Consequently, the repository emission rates presented here should be considered as preliminary estimates. Another set of air pollution emission rates will be calculated after design data are more firmly established. 18 refs., 15 tabs

Title list of documents made publicly available

International Nuclear Information System (INIS)

1990-04-01

This document is a monthly publication containing descriptions of information received and generated by the US Nuclear Regulatory Commission (NRC). This information includes (1) docketed material associated with civilian nuclear power plants and other uses of radioactive materials, and (2) nondocketed material received and generated by NRC pertinent to its role as a regulatory agency. The following indexes are included: Personal Author, Corporate Source, Report Number, and Cross Reference to Principal Documents

Influence of iodine chemistry on source term assessment

International Nuclear Information System (INIS)

Herranz Puebla, L. E.; Lopez Diez, I.; Rodriguez Maroto, J. J.; Martinez Lopez-Alcorocho, A.

1991-01-01

The major goal of a phenomenology analysis of containment during a severe accident situation can be spitted into the following ones: to know the containment response to the different loads and to predict accurately the fission product and aerosol behavior. In this report, the main results coming from the study of a hypothetical accident scenario, based on LA-4 experiment of LACE project, are presented. In order to do it, several codes have been coupled: CONTEMPT4/MOD5 (thermohydraulics), NAUA/MOD5 (aerosol physics) and IODE (iodine chemistry). It has been demonstrated the impossibility of assessing with confidence the Source Term if the chemical conduct of some radionuclides is not taken into account. In particular, the influence on the iodine retention efficiency of the sump of variables such as pH has been proven. (Author)12 refs

Source term assessment using inverse modeling of radiation dose measured with environmental radiation monitors located at different positions

International Nuclear Information System (INIS)

Srinivas, C.V.; Rakesh, P.T.; Baskaran, R.; Venkatraman, B.

2018-01-01

Source term is an important input for consequence analysis using Decision Support Systems (DSS) to project radiological impact in the event of nuclear emergencies. A source term model called 'ASTER' is incorporated in the Online Nuclear Emergency Response System (ONERS) operational at Kalpakkam site for decision making during nuclear emergencies. This computes release rates using inverse method by employing an atmospheric dispersion model and gamma dose rates measured by environmental radiation monitors (ERM) deployed around the nuclear plant. The estimates may depend on the distribution of ERMs around the release location. In this work, data from various gamma monitors located at different radii 0.75 km and 1.5 km is used to assess the accuracy in the source term estimation for stack releases of MAPS-PHWR at Kalpakkam

Final report of the inter institutional project ININ-CNSNS 'Source Terms specific for the CNLV'

International Nuclear Information System (INIS)

Anaya M, R.A.

1991-02-01

The purpose of the project inter institutional ININ-CNSNS 'Source Terms Specifies for the CNLV' it is the one of implanting in the computer CYBER (CDC 180-830) of the ININ, the 'Source Term Code Package' (STCP) and to make the operation tests and corresponding operation using the data of the sample problem, for finally to liberate the package, all time that by means of the analysis of the results it is consider appropriate. In this report the results of the are presented simulation of the sequence 'Energy Losses external' (Station blackout) and 'Lost total of CA with failure of the RCIC and success of the HPCS' both with data of the Laguna Verde Central. (Author)

31 CFR 501.724 - Documents that may be withheld.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Documents that may be withheld. 501.724 Section 501.724 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued... privileged; (2) The document would disclose the identity of a confidential source; or (3) The Administrative...

Documentation of Cultural Heritage Objects

Directory of Open Access Journals (Sweden)

Jon Grobovšek

2013-09-01

the needs of potential users. Inadequate archiving may cause irreversible damage to documents. It is unreasonable to store data in a format which could not be read by future generations. In spite of high capacity of data bases the aspect of long term archiving of analogue documents should not be neglected. The past is being stored for the future, including different methods of storing various types of historical archives.

Air pollutant emission rates for sources at the Davis Canyon Repository site

International Nuclear Information System (INIS)

1985-11-01

This document summarizes the air-quality source terms used for the Davis Canyon, Utah environmental assessment report and explains their derivation. The engineering data supporting these source terms appear as appendixes to the report and include summary equipment lists for the repository (December, 1984) and detailed equipment lists for the exploratory shaft (June and July, 1985). Although substantial work has been performed in establishing the current repository design, a greater effort will be required for the final design. Consequently, the repository emission rates presented here should be considered as preliminary estimates. Another set of air pollutant emission rates will be calculated after design data are more firmly established. 19 refs., 18 tabs

Analysis of the Variability of Classified and Unclassified Radiological Source term Inventories in the Frenchman Flat Area, Nevada test Site

International Nuclear Information System (INIS)

Zhao, P.; Zavarin, M.

2008-01-01

It has been proposed that unclassified source terms used in the reactive transport modeling investigations at NTS CAUs should be based on yield-weighted source terms calculated using the average source term from Bowen et al. (2001) and the unclassified announced yields reported in DOE/NV-209. This unclassified inventory is likely to be used in unclassified contaminant boundary calculations and is, thus, relevant to compare to the classified inventory. They have examined the classified radionuclide inventory produced by 10 underground nuclear tests conducted in the Frenchman Flat (FF) area of the Nevada Test Site. The goals were to (1) evaluate the variability in classified radiological source terms among the 10 tests and (2) compare that variability and inventory uncertainties to an average unclassified inventory (e.g. Bowen 2001). To evaluate source term variability among the 10 tests, radiological inventories were compared on two relative scales: geometric mean and yield-weighted geometric mean. Furthermore, radiological inventories were either decay corrected to a common date (9/23/1992) or the time zero (t 0 ) of each test. Thus, a total of four data sets were produced. The date of 9/23/1992 was chosen based on the date of the last underground nuclear test at the Nevada Test Site

Long-term trends in California mobile source emissions and ambient concentrations of black carbon and organic aerosol.

Science.gov (United States)

McDonald, Brian C; Goldstein, Allen H; Harley, Robert A

2015-04-21

A fuel-based approach is used to assess long-term trends (1970-2010) in mobile source emissions of black carbon (BC) and organic aerosol (OA, including both primary emissions and secondary formation). The main focus of this analysis is the Los Angeles Basin, where a long record of measurements is available to infer trends in ambient concentrations of BC and organic carbon (OC), with OC used here as a proxy for OA. Mobile source emissions and ambient concentrations have decreased similarly, reflecting the importance of on- and off-road engines as sources of BC and OA in urban areas. In 1970, the on-road sector accounted for ∼90% of total mobile source emissions of BC and OA (primary + secondary). Over time, as on-road engine emissions have been controlled, the relative importance of off-road sources has grown. By 2010, off-road engines were estimated to account for 37 ± 20% and 45 ± 16% of total mobile source contributions to BC and OA, respectively, in the Los Angeles area. This study highlights both the success of efforts to control on-road emission sources, and the importance of considering off-road engine and other VOC source contributions when assessing long-term emission and ambient air quality trends.

Source term development for tritium at the Sheffield disposal site

International Nuclear Information System (INIS)

MacKenzie, D.R.; Barletta, R.E.; Smalley, J.F.; Kempf, C.R.; Davis, R.E.

1984-01-01

The Sheffield low-level radioactive waste disposal site, which ceased operation in 1978, has been the focus of modeling efforts by the NRC for the purpose of predicting long-term site behavior. To provide the NRC with the information required for its modeling effort, a study to define the source term for tritium in eight trenches at the Sheffield site has been undertaken. Tritium is of special interest since significant concentrations of the isotope have been found in groundwater samples taken at the site and at locations outside the site boundary. Previous estimates of tritium site inventory at Sheffield are in wide disagreement. In this study, the tritium inventory in the eight trenches was estimated by reviewing the radioactive shipping records (RSRs) for waste buried in these trenches. It has been found that the tritium shipped for burial at the site was probably higher than previously estimated. In the eight trenches surveyed, which amount to roughly one half the total volume and activity buried at Sheffield, approximately 2350 Ci of tritium from non-fuel cycle sources were identified. The review of RSRs also formed the basis for obtaining waste package descriptions and for contacting large waste generators to obtain more detailed information regarding these waste packages. As a result of this review and the selected generator contacts, the non-fuel cycle tritium waste was categorized. The tritium releases from each of these waste categories were modeled. The results of this modeling effort are presented for each of the eight trenches selected. 3 references, 2 figures

Projected Source Terms for Potential Sabotage Events Related to Spent Fuel Shipments

International Nuclear Information System (INIS)

Luna, R.E.; Neuhauser, K.S.; Vigil, M.G.

1999-01-01

Two major studies, one sponsored by the U.S. Department of Energy and the other by the U.S. Nuclear Regulatory Commission, were conducted in the late 1970s and early 1980s to provide information and source terms for an optimally successful act of sabotage on spent fuel casks typical of those available for use. This report applies the results of those studies and additional analysis to derive potential source terms for certain classes of sabotage events on spent fuel casks and spent fuel typical of those which could be shipped in the early decades of the 21st century. In addition to updating the cask and spent fuel characteristics used in the analysis, two release mechanisms not included in the earlier works were identified and evaluated. As would be expected, inclusion of these additional release mechanisms resulted in a somewhat higher total release from the postulated sabotage events. Although health effects from estimated releases were addressed in the earlier study conducted for U.S. Department of Energy, they have not been addressed in this report. The results from this report maybe used to estimate health effects

Title list of documents made publicly available. Documents from October-December 1978 for Dockets 50-334 through STN 50-597

International Nuclear Information System (INIS)

1978-01-01

This special edition of the Title List contains Docket 50 material from 1978 that has not appeared in previous issues of the Title List. The documents in this supplement are indexed by personal author, corporate source, and report number. The listings of this material on the domestic licensing of production and utilization facilities, divided into the categories used for filing and searching in the NRC Public Document Room, are presented

Utility-preserving privacy protection of textual healthcare documents.

Science.gov (United States)

Sánchez, David; Batet, Montserrat; Viejo, Alexandre

2014-12-01

The adoption of ITs by medical organisations makes possible the compilation of large amounts of healthcare data, which are quite often needed to be released to third parties for research or business purposes. Many of this data are of sensitive nature, because they may include patient-related documents such as electronic healthcare records. In order to protect the privacy of individuals, several legislations on healthcare data management, which state the kind of information that should be protected, have been defined. Traditionally, to meet with current legislations, a manual redaction process is applied to patient-related documents in order to remove or black-out sensitive terms. This process is costly and time-consuming and has the undesired side effect of severely reducing the utility of the released content. Automatic methods available in the literature usually propose ad-hoc solutions that are limited to protect specific types of structured information (e.g. e-mail addresses, social security numbers, etc.); as a result, they are hardly applicable to the sensitive entities stated in current regulations that do not present those structural regularities (e.g. diseases, symptoms, treatments, etc.). To tackle these limitations, in this paper we propose an automatic sanitisation method for textual medical documents (e.g. electronic healthcare records) that is able to protect, regardless of their structure, sensitive entities (e.g. diseases) and also those semantically related terms (e.g. symptoms) that may disclose the former ones. Contrary to redaction schemes based on term removal, our approach improves the utility of the protected output by replacing sensitive terms with appropriate generalisations retrieved from several medical and general-purpose knowledge bases. Experiments conducted on highly sensitive documents and in coherency with current regulations on healthcare data privacy show promising results in terms of the practical privacy and utility of the

Basic repository source term and data sheet report: Deaf Smith County

International Nuclear Information System (INIS)

1987-01-01

This report is one of a series describing studies undertaken in support of the US Department of Energy Civilian Radioactive Waste Management (CRWM) Program. This study contains the derivation of values for environmental source terms and resources consumed for a CRWM repository. Estimates include heavy construction equipment; support equipment; shaft-sinking equipment; transportation equipment; and consumption of fuel, water, electricity, and natural gas. Data are presented for construction and operation at an assumed site in Deaf Smith County, Texas. 2 refs., 6 tabs

New source terms: what do they tell us about engineered safety feature performance

International Nuclear Information System (INIS)

Bernero, R.M.

1985-01-01

The accident behavior models which are the basis of engineered safety feature design are generally simple, non-mechanistic and concentrated on volatile radioiodine. Now data from source term studies show that models should be more mechanistic and look at other species than volatile iodine. A complete reevaluation of engineered safety features is needed

Clustering document fragments using background color and texture information

Science.gov (United States)

Chanda, Sukalpa; Franke, Katrin; Pal, Umapada

2012-01-01

Forensic analysis of questioned documents sometimes can be extensively data intensive. A forensic expert might need to analyze a heap of document fragments and in such cases to ensure reliability he/she should focus only on relevant evidences hidden in those document fragments. Relevant document retrieval needs finding of similar document fragments. One notion of obtaining such similar documents could be by using document fragment's physical characteristics like color, texture, etc. In this article we propose an automatic scheme to retrieve similar document fragments based on visual appearance of document paper and texture. Multispectral color characteristics using biologically inspired color differentiation techniques are implemented here. This is done by projecting document color characteristics to Lab color space. Gabor filter-based texture analysis is used to identify document texture. It is desired that document fragments from same source will have similar color and texture. For clustering similar document fragments of our test dataset we use a Self Organizing Map (SOM) of dimension 5×5, where the document color and texture information are used as features. We obtained an encouraging accuracy of 97.17% from 1063 test images.

Sealed radioactive source management

International Nuclear Information System (INIS)

2005-01-01

Sealed radioactive sources have been used in a wide range of application in medicine, agriculture, geology, industry and other fields. Since its utilization many sources have become out of use and became waste but no proper management. This has lead to many accidents causing deaths and serious radiation injuries worldwide. Spent sources application is expanding but their management has seen little improvements. Sealed radioactive sources have become a security risk calling for prompt action. Source management helps to maintain sources in a good physical status and provide means of source tracking and control. It also provides a well documented process of the sources making any future management options safe, secure and cost effective. Last but not least good source management substantially reduces the risk of accidents and eliminates the risk of malicious use. The International Atomic Energy Agency assists Member States to build the infrastructure to properly manage sealed radioactive sources. The assistance includes training of national experts to handle, condition and properly store the sources. For Member States that do not have proper facilities, we provide the technical assistance to design a proper facility to properly manage the radioactive sources and provide for their proper storage. For Member States that need to condition their sources properly but don't have the required infrastructure we provide direct assistance to physically help them with source recovery and provide an international expert team to properly condition their sources and render them safe and secure. We offer software (Radioactive Waste Management Registry) to properly keep a complete record on the sources and provide for efficient tracking. This also helps with proper planning and decision making for long term management

Civilian Radioactive Waste Management System Requirements Document

International Nuclear Information System (INIS)

1992-12-01

This document specifies the top-level requirements for the Civilian Radioactive Waste Management System (CRWMS). The document is referred to herein as the CRD, for CRWMS Requirements document. The OCRWM System Engineering Management Plan (SEMP) establishes the technical document hierarchy (hierarchy of technical requirements and configuration baseline documents) for the CRWMS program. The CRD is the top-level document in this hierarchy. The immediate subordinate documents are the System Requirements Documents (SRDS) for the four elements of the CRWMS and the Interface Specification (IFS). The four elements of the CRWMS are the Waste Acceptance System, the Transportation System, the Monitored Retrievable Storage (MRS) System and the Mined Geologic Disposal System (MGDS). The Interface Specification describes the six inter-element interfaces between the four elements. This hierarchy establishes the requirements to be addressed by the design of the system elements. Many of the technical requirements for the CRWMS are documented in a variety of Federal regulations, DOE directives and other Government documentation. It is the purpose of the CRD to establish the technical requirements for the entire program. In doing so, the CRD summarizes source documentation for requirements that must be addressed by the program, specifies particular requirements, and documents derived requirements that are not covered in regulatory and other Government documentation, but are necessary to accomplish the mission of the CRWMS. The CRD defines the CRWMS by identifying the top-level functions the elements must perform (These top-level functions were derived using functional analysis initially documented in the Physical System Requirements (PSR) documents). The CRD also defines the top-level physical architecture of the system and allocates the functions and requirements to the architectural elements of the system

Dose assessments for Greifswald and Cadarache with updated source terms from ITER NSSR-2

International Nuclear Information System (INIS)

Raskob, W.; Hasemann, I.

1998-08-01

The International Thermonuclear Experimental Reactor ITER is in its late engineering phase. One of the most important safety aspects - in particular for achieving public acceptance - is to assure that the releases of harzardous material are minimal during normal operation and for accidental events, even if very unlikely. To this purpose probabilistic dose assessments for accidental atmospheric releases of various ITER source terms which contain tritium and/or activation products were performed for the sites of Greifswald, Germany, and Cadarache, France. In addition, routine releases into the atmosphere and hydrosphere have been evaluated. No country specific rules were applied and the input parameters were adapted as far as possible to those used within former studies to achieve a better comparability with site independent dose assessments performed in the frame of ITER. The calculations were based on source terms which, for the first time, contain a combination of tritium and activation products. This allowed a better judgment of the contribution to the total dose of the individual fusion relevant materials. The results were compared to site independent dose limits defined in the frame of ITER. Annual doses from routine releases (CAT-I) are below 0.1 μSv for the aquatic scenarios and are close to 1 μSv for the atmospheric source terms. Source terms for two different categories of accidental releases, representing 'extremely unlikely events' (CAT-IV) and 'hypothetical sequences' (CAT-V), were investigated. In none of these cases, the release scenarios of category CAT-IV exceed the ITER limits. In addition, relevant characteristic quantities of the early dose distribution from the hypothetical scenarios of type CAT-V are still below 50 mSv or 100 mSv, values which are commonly used as lower reference values for evacuation in many potential home countries of ITER. These site specific assessments confirmed that the proposed release limits and thus the derived dose

REVEAL: Software Documentation and Platform Migration

Science.gov (United States)

Wilson, Michael A.; Veibell, Victoir T.; Freudinger, Lawrence C.

2008-01-01

The Research Environment for Vehicle Embedded Analysis on Linux (REVEAL) is reconfigurable data acquisition software designed for network-distributed test and measurement applications. In development since 2001, it has been successfully demonstrated in support of a number of actual missions within NASA s Suborbital Science Program. Improvements to software configuration control were needed to properly support both an ongoing transition to operational status and continued evolution of REVEAL capabilities. For this reason the project described in this report targets REVEAL software source documentation and deployment of the software on a small set of hardware platforms different from what is currently used in the baseline system implementation. This report specifically describes the actions taken over a ten week period by two undergraduate student interns and serves as a final report for that internship. The topics discussed include: the documentation of REVEAL source code; the migration of REVEAL to other platforms; and an end-to-end field test that successfully validates the efforts.

Technical Document on Control of Nitrogen Oxides From Municipal Waste Combustors

Science.gov (United States)

This document may be of assistance in applying the New Source Review (NSR) air permitting regulations including the Prevention of Significant Deterioration (PSD) requirements. This document is part of the NSR Policy and Guidance Database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

Every document and picture tells a story: using internal corporate document reviews, semiotics, and content analysis to assess tobacco advertising.

Science.gov (United States)

Anderson, S J; Dewhirst, T; Ling, P M

2006-06-01

In this article we present communication theory as a conceptual framework for conducting documents research on tobacco advertising strategies, and we discuss two methods for analysing advertisements: semiotics and content analysis. We provide concrete examples of how we have used tobacco industry documents archives and tobacco advertisement collections iteratively in our research to yield a synergistic analysis of these two complementary data sources. Tobacco promotion researchers should consider adopting these theoretical and methodological approaches.

Improving the Product Documentation Process of a Small Software Company

Science.gov (United States)

Valtanen, Anu; Ahonen, Jarmo J.; Savolainen, Paula

Documentation is an important part of the software process, even though it is often neglected in software companies. The eternal question is how much documentation is enough. In this article, we present a practical implementation of lightweight product documentation process resulting from SPI efforts in a small company. Small companies’ financial and human resources are often limited. The documentation process described here, offers a template for creating adequate documentation consuming minimal amount of resources. The key element of the documentation process is an open source web-based bugtracking system that was customized to be used as a documentation tool. The use of the tool enables iterative and well structured documentation. The solution best serves the needs of a small company with off-the-shelf software products and striving for SPI.

MIT/OSO 7 catalog of x-ray sources: intensities, spectra, and long-term variability

International Nuclear Information System (INIS)

Markert, T.H.; Winkler, P.F.; Laird, F.N.; Clark, G.W.; Hearn, D.R.; Sprott, G.F.; Li, F.K.; Bradt, H.V.; Lewin, W.H.G.; Schnopper, H.W.

1979-01-01

This paper is a summary of the observations of the cosmic X-ray sky performed by the MIT 1--40 KeV X-ray detectors on the OSO 7 between 1971 October and 1973 May. Specifically, we have computed the mean intensities or upper limits of all third Uhuru or OSO 7 cataloged sources (185 sources) in the 3--10 KeV range. For those sources for which a statistically significant (>20) intensity was found in the 3--10 KeV band (138 sources), further intensity determinations were made in the 1--15 KeV, 1--6 KeV, and 15--40 KeV energy bands. We have provided graphs and other simple techniques to aid the user in converting the observed counting rates to convenient units and in determining spectral parameters. Finally, we have plotted long-term light curves (counting rates in one or more energy bands as a function of time) for 86 of the brighter sources

Source term and behavioural parameters for a postulated HIFAR loss-of-coolant accident

International Nuclear Information System (INIS)

May, F.G.

1987-01-01

The fraction of the fission product inventory which might be released into the atmosphere of the HIFAR reactor containment building (RCB) during a postulated loss-of-coolant accident (LOCA) has been evaluated as a function of time, for each classification of airborne radioactivity. This appraisal will be used as the source term for a computer program, which uses realistic attenuation of the fission product aerosol in a single compartment model with a defined leakrate to predict possible radioactive releases into the environment in a hypothetical bounding case reactor accident which is rather more severe in all major aspects than any single LOCA. Also given are the parameters governing the attenuation of the aerosol and vapours in the atmosphere of the RCB so that their behaviour may be accurately modelled. The source terms for several other types of accident involving the meltdown of fuel elements have also been considered but in less detail than the LOCA case. In some of the cases, the fission products are released directly to atmosphere, so there is no attenuation of the release by deposition within the RCB

Radiation Protection Aspects of Primary Water Chemistry and Source-term Management Report

International Nuclear Information System (INIS)

2014-04-01

Since the beginning of the 1990's, occupational exposures in nuclear power plant has strongly decreased, outlining efforts achieved by worldwide nuclear operators in order to reach and maintain occupational exposure as low as reasonably achievable (ALARA) in accordance with international recommendations and national regulations. These efforts have focused on both technical and organisational aspects. According to many radiation protection experts, one of the key features to reach this goal is the management of the primary system water chemistry and the ability to avoid dissemination of radioactivity within the system. It outlines the importance for radiation protection staff to work closely with chemistry staff (as well as operation staff) and thus to have sufficient knowledge to understand the links between chemistry and the generation of radiation field. This report was prepared with the primary objective to provide such knowledge to 'non-chemist'. The publication primarily focuses on three topics dealing with water chemistry, source term management and remediation techniques. One key objective of the report is to provide current knowledge regarding these topics and to address clearly related radiation protection issues. In that mind, the report prepared by the EGWC was also reviewed by radiation protection experts. In order to address various designs, PWRs, VVERs, PHWRs and BWRs are addressed within the document. Additionally, available information addressing current operating units and lessons learnt is outlined with choices that have been made for the design of new plants. Chapter 3 of this report addresses current practices regarding primary chemistry management for different designs, 'how to limit activity in the primary circuit and to minimise contamination'. General information is provided regarding activation, corrosion and transport of activated materials in the primary circuit (background on radiation field generation). Primary chemistry aspects that

Getting more out of biomedical documents with GATE's full lifecycle open source text analytics.

Science.gov (United States)

Cunningham, Hamish; Tablan, Valentin; Roberts, Angus; Bontcheva, Kalina

2013-01-01

This software article describes the GATE family of open source text analysis tools and processes. GATE is one of the most widely used systems of its type with yearly download rates of tens of thousands and many active users in both academic and industrial contexts. In this paper we report three examples of GATE-based systems operating in the life sciences and in medicine. First, in genome-wide association studies which have contributed to discovery of a head and neck cancer mutation association. Second, medical records analysis which has significantly increased the statistical power of treatment/outcome models in the UK's largest psychiatric patient cohort. Third, richer constructs in drug-related searching. We also explore the ways in which the GATE family supports the various stages of the lifecycle present in our examples. We conclude that the deployment of text mining for document abstraction or rich search and navigation is best thought of as a process, and that with the right computational tools and data collection strategies this process can be made defined and repeatable. The GATE research programme is now 20 years old and has grown from its roots as a specialist development tool for text processing to become a rather comprehensive ecosystem, bringing together software developers, language engineers and research staff from diverse fields. GATE now has a strong claim to cover a uniquely wide range of the lifecycle of text analysis systems. It forms a focal point for the integration and reuse of advances that have been made by many people (the majority outside of the authors' own group) who work in text processing for biomedicine and other areas. GATE is available online under GNU open source licences and runs on all major operating systems. Support is available from an active user and developer community and also on a commercial basis.

Getting more out of biomedical documents with GATE's full lifecycle open source text analytics.

Directory of Open Access Journals (Sweden)

Hamish Cunningham

Full Text Available This software article describes the GATE family of open source text analysis tools and processes. GATE is one of the most widely used systems of its type with yearly download rates of tens of thousands and many active users in both academic and industrial contexts. In this paper we report three examples of GATE-based systems operating in the life sciences and in medicine. First, in genome-wide association studies which have contributed to discovery of a head and neck cancer mutation association. Second, medical records analysis which has significantly increased the statistical power of treatment/outcome models in the UK's largest psychiatric patient cohort. Third, richer constructs in drug-related searching. We also explore the ways in which the GATE family supports the various stages of the lifecycle present in our examples. We conclude that the deployment of text mining for document abstraction or rich search and navigation is best thought of as a process, and that with the right computational tools and data collection strategies this process can be made defined and repeatable. The GATE research programme is now 20 years old and has grown from its roots as a specialist development tool for text processing to become a rather comprehensive ecosystem, bringing together software developers, language engineers and research staff from diverse fields. GATE now has a strong claim to cover a uniquely wide range of the lifecycle of text analysis systems. It forms a focal point for the integration and reuse of advances that have been made by many people (the majority outside of the authors' own group who work in text processing for biomedicine and other areas. GATE is available online under GNU open source licences and runs on all major operating systems. Support is available from an active user and developer community and also on a commercial basis.

On the query reformulation technique for effective MEDLINE document retrieval.

Science.gov (United States)

Yoo, Sooyoung; Choi, Jinwook

2010-10-01

Improving the retrieval accuracy of MEDLINE documents is still a challenging issue due to low retrieval precision. Focusing on a query expansion technique based on pseudo-relevance feedback (PRF), this paper addresses the problem by systematically examining the effects of expansion term selection and adjustment of the term weights of the expanded query using a set of MEDLINE test documents called OHSUMED. Implementing a baseline information retrieval system based on the Okapi BM25 retrieval model, we compared six well-known term ranking algorithms for useful expansion term selection and then compared traditional term reweighting algorithms with our new variant of the standard Rocchio's feedback formula, which adopts a group-based weighting scheme. Our experimental results on the OHSUMED test collection showed a maximum improvement of 20.2% and 20.4% for mean average precision and recall measures over unexpanded queries when terms were expanded using a co-occurrence analysis-based term ranking algorithm in conjunction with our term reweighting algorithm (p-valueretrieval.

Who has used internal company documents for biomedical and public health research and where did they find them?

Science.gov (United States)

Wieland, L Susan; Rutkow, Lainie; Vedula, S Swaroop; Kaufmann, Christopher N; Rosman, Lori M; Twose, Claire; Mahendraratnam, Nirosha; Dickersin, Kay

2014-01-01

To describe the sources of internal company documents used in public health and healthcare research. We searched PubMed and Embase for articles using internal company documents to address a research question about a health-related topic. Our primary interest was where authors obtained internal company documents for their research. We also extracted information on type of company, type of research question, type of internal documents, and funding source. Our searches identified 9,305 citations of which 357 were eligible. Scanning of reference lists and consultation with colleagues identified 4 additional articles, resulting in 361 included articles. Most articles examined internal tobacco company documents (325/361; 90%). Articles using documents from pharmaceutical companies (20/361; 6%) were the next most common. Tobacco articles used documents from repositories; pharmaceutical documents were from a range of sources. Most included articles relied upon internal company documents obtained through litigation (350/361; 97%). The research questions posed were primarily about company strategies to promote or position the company and its products (326/361; 90%). Most articles (346/361; 96%) used information from miscellaneous documents such as memos or letters, or from unspecified types of documents. When explicit information about study funding was provided (290/361 articles), the most common source was the US-based National Cancer Institute. We developed an alternative and more sensitive search targeted at identifying additional research articles using internal pharmaceutical company documents, but the search retrieved an impractical number of citations for review. Internal company documents provide an excellent source of information on health topics (e.g., corporate behavior, study data) exemplified by articles based on tobacco industry documents. Pharmaceutical and other industry documents appear to have been less used for research, indicating a need for funding for

Distance matters! Cumulative proximity expansions for ranking documents

NARCIS (Netherlands)

J.B.P. Vuurens (Jeroen); A.P. de Vries (Arjen)

2014-01-01

htmlabstractIn the information retrieval process, functions that rank documents according to their estimated relevance to a query typically regard query terms as being independent. However, it is often the joint presence of query terms that is of interest to the user, which is overlooked when

Reciprocity relations and the mode conversion-absorption equation with an inhomogeneous source term

International Nuclear Information System (INIS)

Cho, S.; Swanson, D.G.

1990-01-01

The fourth-order mode conversion equation is solved completely via the Green's function to include an inhomogeneous source term. This Green's function itself contains all the plasma responsive effects such as mode conversion and absorption, and can be used to describe the spontaneous emission. In the course of the analysis, the reciprocity relations between coupling parameters are proved

The EC CAST project (carbon-14 source term)

International Nuclear Information System (INIS)

Williams, S. J.

2015-01-01

Carbon-14 is a key radionuclide in the assessment of the safety of underground geological disposal facilities for radioactive wastes. It is possible for carbon-14 to be released from waste packages in a variety of chemical forms, both organic and inorganic, and as dissolved or gaseous species The EC CAST (CArbon-14 Source Term) project aims to develop understanding of the generation and release of carbon-14 from radioactive waste materials under conditions relevant to packaging and disposal. It focuses on the release of carbon-14 from irradiated metals (steels and zirconium alloys), from irradiated graphite and from spent ion-exchange resins. The CAST consortium brings together 33 partners. CAST commenced in October 2013 and this paper describes progress to March 2015. The main activities during this period were reviews of the current status of knowledge, the identification and acquisition of suitable samples and the design of experiments and analytical procedures. (authors)

Mapping of the flux and estimate of the radiation source term of neutron fields generated by the GE PETtrace-8 cyclotron

International Nuclear Information System (INIS)

Benavente Castillo, Jhonny Antonio

2017-01-01

The use of spectrometric techniques in a cyclotron facility is strongly advised for the complete characterization of the neutron radiation field. In recent years, several studies of neutron spectrometry have been carried out at the Cyclotron of the Development Center of Nuclear Technology (CDTN). The main objective of this work is to propose a methodology for mapping of the flux and estimate of the radiation source term of neutron fields generated by the GE PETtrace-8 cyclotron. The method of neutron activation analysis with gold, indium and nickel activation foils was used to measure the activities induced at specific points in the cyclotron bunker. The irradiations of the activation foils were performed using the intermittent irradiation method to optimize the radiation field during 18 F production. The study of the neutron spectrum was performed using three radiation source terms. The first source term was constructed based on data provided by the cyclotron manufacturer using the neutron cross sections of the ENDF/B-VII library. The other two were proposed considering the irradiation process used in the routine of 18 F production. Both radiation source terms used the LA150H proton cross sections and for the 18 O, the cross sections of the physical model CEM03 (Cascade-exciton model) and TENDL (TALYS-based Evaluated Nuclear Data Library) were used. The results of the source terms in relation to the experimental results, in terms of neutron fluence rates, reaction rates and dose equivalent rates, showed that are in the same order of magnitude as those obtained by Ogata et al, Fujibuchi et al, and Gallerani et al., for the same cyclotron; and by Mendez et al. for a different manufacturing cyclotron. The models of the proposed radiation source terms were validated to obtain the spectra generated during the 18 F production when water enriched at 18 O is bombarded with a proton beam of 16.5 MeV. Finally, the model of the LA150H - TENDL - 2015 radiation source term is

Incremental Ontology-Based Extraction and Alignment in Semi-structured Documents

Science.gov (United States)

Thiam, Mouhamadou; Bennacer, Nacéra; Pernelle, Nathalie; Lô, Moussa

SHIRIis an ontology-based system for integration of semi-structured documents related to a specific domain. The system’s purpose is to allow users to access to relevant parts of documents as answers to their queries. SHIRI uses RDF/OWL for representation of resources and SPARQL for their querying. It relies on an automatic, unsupervised and ontology-driven approach for extraction, alignment and semantic annotation of tagged elements of documents. In this paper, we focus on the Extract-Align algorithm which exploits a set of named entity and term patterns to extract term candidates to be aligned with the ontology. It proceeds in an incremental manner in order to populate the ontology with terms describing instances of the domain and to reduce the access to extern resources such as Web. We experiment it on a HTML corpus related to call for papers in computer science and the results that we obtain are very promising. These results show how the incremental behaviour of Extract-Align algorithm enriches the ontology and the number of terms (or named entities) aligned directly with the ontology increases.

Aiding the Interpretation of Ancient Documents

DEFF Research Database (Denmark)

Roued-Cunliffe, Henriette

How can Decision Support System (DSS) software aid the interpretation process involved in the reading of ancient documents? This paper discusses the development of a DSS prototype for the reading of ancient texts. In this context the term ‘ancient documents’ is used to describe mainly Greek...... tool it is important first to comprehend the interpretation process involved in reading ancient documents. This is not a linear process but rather a recursive process where the scholar moves between different levels of reading, such as ‘understanding the meaning of a character’ or ‘understanding...

Semantic Document Library: A Virtual Research Environment for Documents, Data and Workflows Sharing

Science.gov (United States)

Kotwani, K.; Liu, Y.; Myers, J.; Futrelle, J.

2008-12-01

The Semantic Document Library (SDL) was driven by use cases from the environmental observatory communities and is designed to provide conventional document repository features of uploading, downloading, editing and versioning of documents as well as value adding features of tagging, querying, sharing, annotating, ranking, provenance, social networking and geo-spatial mapping services. It allows users to organize a catalogue of watershed observation data, model output, workflows, as well publications and documents related to the same watershed study through the tagging capability. Users can tag all relevant materials using the same watershed name and find all of them easily later using this tag. The underpinning semantic content repository can store materials from other cyberenvironments such as workflow or simulation tools and SDL provides an effective interface to query and organize materials from various sources. Advanced features of the SDL allow users to visualize the provenance of the materials such as the source and how the output data is derived. Other novel features include visualizing all geo-referenced materials on a geospatial map. SDL as a component of a cyberenvironment portal (the NCSA Cybercollaboratory) has goal of efficient management of information and relationships between published artifacts (Validated models, vetted data, workflows, annotations, best practices, reviews and papers) produced from raw research artifacts (data, notes, plans etc.) through agents (people, sensors etc.). Tremendous scientific potential of artifacts is achieved through mechanisms of sharing, reuse and collaboration - empowering scientists to spread their knowledge and protocols and to benefit from the knowledge of others. SDL successfully implements web 2.0 technologies and design patterns along with semantic content management approach that enables use of multiple ontologies and dynamic evolution (e.g. folksonomies) of terminology. Scientific documents involved with

M2 priority screening system for near-term activities: Project documentation. Final report December 11, 1992--May 31, 1994

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-08-12

From May through August, 1993, the M-2 Group within M Division at LANL conducted with the support of the LANL Integration and Coordination Office (ICO) and Applied Decision Analysis, Inc. (ADA), whose purpose was to develop a system for setting priorities among activities. This phase of the project concentrated on prioritizing near-tenn activities (i.e., activities that must be conducted in the next six months) necessary for setting up this new group. Potential future project phases will concentrate on developing a tool for setting priorities and developing annual budgets for the group`s operations. The priority screening system designed to address the near-term problem was developed, applied in a series of meeting with the group managers, and used as an aid in the assignment of tasks to group members. The model was intended and used as a practical tool for documenting and explaining decisions about near-term priorities, and not as a substitute for M-2 management judgment and decision-making processes.

SNF AGING SYSTEM DESCRIPTION DOCUMENT

Energy Technology Data Exchange (ETDEWEB)

L.L. Swanson

2005-04-06

The purpose of this system description document (SDD) is to establish requirements that drive the design of the spent nuclear fuel (SNF) aging system and associated bases, which will allow the design effort to proceed. This SDD will be revised at strategic points as the design matures. This SDD identifies the requirements and describes the system design, as it currently exists, with emphasis on attributes of the design provided to meet the requirements. This SDD is an engineering tool for design control; accordingly, the primary audience and users are design engineers. This SDD is part of an iterative design process. It leads the design process with regard to the flow down of upper tier requirements onto the system. Knowledge of these requirements is essential in performing the design process. The SDD follows the design with regard to the description of the system. The description provided in the SDD reflects the current results of the design process. Throughout this SDD, the term aging cask applies to vertical site-specific casks and to horizontal aging modules. The term overpack is a vertical site-specific cask that contains a dual-purpose canister (DPC) or a disposable canister. Functional and operational requirements applicable to this system were obtained from ''Project Functional and Operational Requirements'' (F&OR) (Curry 2004 [DIRS 170557]). Other requirements that support the design process were taken from documents such as ''Project Design Criteria Document'' (PDC) (BSC 2004 [DES 171599]), ''Site Fire Hazards Analyses'' (BSC 2005 [DIRS 172174]), and ''Nuclear Safety Design Bases for License Application'' (BSC 2005 [DIRS 171512]). The documents address requirements in the ''Project Requirements Document'' (PRD) (Canori and Leitner 2003 [DIRS 166275]). This SDD includes several appendices. Appendix A is a Glossary; Appendix B is a list of key system charts

SNF AGING SYSTEM DESCRIPTION DOCUMENT

International Nuclear Information System (INIS)

L.L. Swanson

2005-01-01

The purpose of this system description document (SDD) is to establish requirements that drive the design of the spent nuclear fuel (SNF) aging system and associated bases, which will allow the design effort to proceed. This SDD will be revised at strategic points as the design matures. This SDD identifies the requirements and describes the system design, as it currently exists, with emphasis on attributes of the design provided to meet the requirements. This SDD is an engineering tool for design control; accordingly, the primary audience and users are design engineers. This SDD is part of an iterative design process. It leads the design process with regard to the flow down of upper tier requirements onto the system. Knowledge of these requirements is essential in performing the design process. The SDD follows the design with regard to the description of the system. The description provided in the SDD reflects the current results of the design process. Throughout this SDD, the term aging cask applies to vertical site-specific casks and to horizontal aging modules. The term overpack is a vertical site-specific cask that contains a dual-purpose canister (DPC) or a disposable canister. Functional and operational requirements applicable to this system were obtained from ''Project Functional and Operational Requirements'' (F andOR) (Curry 2004 [DIRS 170557]). Other requirements that support the design process were taken from documents such as ''Project Design Criteria Document'' (PDC) (BSC 2004 [DES 171599]), ''Site Fire Hazards Analyses'' (BSC 2005 [DIRS 172174]), and ''Nuclear Safety Design Bases for License Application'' (BSC 2005 [DIRS 171512]). The documents address requirements in the ''Project Requirements Document'' (PRD) (Canori and Leitner 2003 [DIRS 166275]). This SDD includes several appendices. Appendix A is a Glossary; Appendix B is a list of key system charts, diagrams, drawings, lists and additional supporting information; and Appendix C is a list of

Loss of confinement of liquefied gases. Evaluation of the source term; Perte de confinement de gaz liquefies. Evaluation du terme source

Energy Technology Data Exchange (ETDEWEB)

Alix, P.; Novat, E.; Hocquet, J.; Bigot, J.P. [Ecole Nationale Superieure des Mines, Centre SPIN, 42 - Saint-Etienne (France)

2001-07-01

In this work, the states law corresponding to flow rate measurements of two-phase flows performed with five different fluid (water, butane, R11, ethyl acetate, methanol) is applied. This allows to show that the critical mass flux (which is used as source term in the scenario of loss of confinement in liquefied gas reservoirs) is a 'universal' function of the reduced initial pressure P{sub 0}{sup *}, which can be used for most of the single-constituent fluids of the processes industry. Thus it is easy to make a relatively precise estimation of the critical mass flux (uncertainty < 20% for P{sub 0}{sup *} < 15%) without the need of any model. It is shown also that no improvement of the models can be expected from the use of the vaporization kinetics. On the contrary, a qualitative consideration indicates that the use of the slip seems more promising. (J.S.)

RELIABLE COGNITIVE DIMENSIONAL DOCUMENT RANKING BY WEIGHTED STANDARD CAUCHY DISTRIBUTION

Directory of Open Access Journals (Sweden)

S Florence Vijila

2017-04-01

Full Text Available Categorization of cognitively uniform and consistent documents such as University question papers are in demand by e-learners. Literature indicates that Standard Cauchy distribution and the derived values are extensively used for checking uniformity and consistency of documents. The paper attempts to apply this technique for categorizing question papers according to four selective cognitive dimensions. For this purpose cognitive dimensional keyword sets of these four categories (also termed as portrayal concepts are assumed and an automatic procedure is developed to quantify these dimensions in question papers. The categorization is relatively accurate when checked with manual methods. Hence simple and well established term frequency / inverse document frequency ‘tf/ IDF’ technique is considered for automating the categorization process. After the documents categorization, standard Cauchy formula is applied to rank order the documents that have the least differences among Cauchy value, (according to Cauchy theorem so as obtain consistent and uniform documents in an order or ranked. For the purpose of experiments and social survey, seven question papers (documents have been designed with various consistencies. To validate this proposed technique social survey is administered on selective samples of e-learners of Tamil Nadu, India. Results are encouraging and conclusions drawn out of the experiments will be useful to researchers of concept mining and categorizing documents according to concepts. Findings have also contributed utility value to e-learning system designers.

Semantic Similarity between Web Documents Using Ontology

Science.gov (United States)

Chahal, Poonam; Singh Tomer, Manjeet; Kumar, Suresh

2018-06-01

The World Wide Web is the source of information available in the structure of interlinked web pages. However, the procedure of extracting significant information with the assistance of search engine is incredibly critical. This is for the reason that web information is written mainly by using natural language, and further available to individual human. Several efforts have been made in semantic similarity computation between documents using words, concepts and concepts relationship but still the outcome available are not as per the user requirements. This paper proposes a novel technique for computation of semantic similarity between documents that not only takes concepts available in documents but also relationships that are available between the concepts. In our approach documents are being processed by making ontology of the documents using base ontology and a dictionary containing concepts records. Each such record is made up of the probable words which represents a given concept. Finally, document ontology's are compared to find their semantic similarity by taking the relationships among concepts. Relevant concepts and relations between the concepts have been explored by capturing author and user intention. The proposed semantic analysis technique provides improved results as compared to the existing techniques.

Semantic Similarity between Web Documents Using Ontology

Science.gov (United States)

Chahal, Poonam; Singh Tomer, Manjeet; Kumar, Suresh

2018-03-01

The World Wide Web is the source of information available in the structure of interlinked web pages. However, the procedure of extracting significant information with the assistance of search engine is incredibly critical. This is for the reason that web information is written mainly by using natural language, and further available to individual human. Several efforts have been made in semantic similarity computation between documents using words, concepts and concepts relationship but still the outcome available are not as per the user requirements. This paper proposes a novel technique for computation of semantic similarity between documents that not only takes concepts available in documents but also relationships that are available between the concepts. In our approach documents are being processed by making ontology of the documents using base ontology and a dictionary containing concepts records. Each such record is made up of the probable words which represents a given concept. Finally, document ontology's are compared to find their semantic similarity by taking the relationships among concepts. Relevant concepts and relations between the concepts have been explored by capturing author and user intention. The proposed semantic analysis technique provides improved results as compared to the existing techniques.

Combining Position Weight Matrices and Document-Term Matrix for Efficient Extraction of Associations of Methylated Genes and Diseases from Free Text

KAUST Repository

Bin Raies, Arwa

2013-10-16

Background:In a number of diseases, certain genes are reported to be strongly methylated and thus can serve as diagnostic markers in many cases. Scientific literature in digital form is an important source of information about methylated genes implicated in particular diseases. The large volume of the electronic text makes it difficult and impractical to search for this information manually.Methodology:We developed a novel text mining methodology based on a new concept of position weight matrices (PWMs) for text representation and feature generation. We applied PWMs in conjunction with the document-term matrix to extract with high accuracy associations between methylated genes and diseases from free text. The performance results are based on large manually-classified data. Additionally, we developed a web-tool, DEMGD, which automates extraction of these associations from free text. DEMGD presents the extracted associations in summary tables and full reports in addition to evidence tagging of text with respect to genes, diseases and methylation words. The methodology we developed in this study can be applied to similar association extraction problems from free text.Conclusion:The new methodology developed in this study allows for efficient identification of associations between concepts. Our method applied to methylated genes in different diseases is implemented as a Web-tool, DEMGD, which is freely available at http://www.cbrc.kaust.edu.sa/demgd/. The data is available for online browsing and download. © 2013 Bin Raies et al.

Combining position weight matrices and document-term matrix for efficient extraction of associations of methylated genes and diseases from free text.

Directory of Open Access Journals (Sweden)

Arwa Bin Raies

Full Text Available BACKGROUND: In a number of diseases, certain genes are reported to be strongly methylated and thus can serve as diagnostic markers in many cases. Scientific literature in digital form is an important source of information about methylated genes implicated in particular diseases. The large volume of the electronic text makes it difficult and impractical to search for this information manually. METHODOLOGY: We developed a novel text mining methodology based on a new concept of position weight matrices (PWMs for text representation and feature generation. We applied PWMs in conjunction with the document-term matrix to extract with high accuracy associations between methylated genes and diseases from free text. The performance results are based on large manually-classified data. Additionally, we developed a web-tool, DEMGD, which automates extraction of these associations from free text. DEMGD presents the extracted associations in summary tables and full reports in addition to evidence tagging of text with respect to genes, diseases and methylation words. The methodology we developed in this study can be applied to similar association extraction problems from free text. CONCLUSION: The new methodology developed in this study allows for efficient identification of associations between concepts. Our method applied to methylated genes in different diseases is implemented as a Web-tool, DEMGD, which is freely available at http://www.cbrc.kaust.edu.sa/demgd/. The data is available for online browsing and download.

Long-term groundwater contamination after source removal—The role of sorbed carbon and nitrogen on the rate of reoxygenation of a treated-wastewater plume on Cape Cod, MA, USA

Science.gov (United States)

Smith, Richard L.; Repert, Deborah A.; Barber, Larry B.; LeBlanc, Denis R.

2013-01-01

The consequences of groundwater contamination can remain long after a contaminant source has been removed. Documentation of natural aquifer recoveries and empirical tools to predict recovery time frames and associated geochemical changes are generally lacking. This study characterized the long-term natural attenuation of a groundwater contaminant plume in a sand and gravel aquifer on Cape Cod, Massachusetts, after the removal of the treated-wastewater source. Although concentrations of dissolved organic carbon (DOC) and other soluble constituents have decreased substantially in the 15 years since the source was removed, the core of the plume remains anoxic and has sharp redox gradients and elevated concentrations of nitrate and ammonium. Aquifer sediment was collected from near the former disposal site at several points in time and space along a 0.5-km-long transect extending downgradient from the disposal site and analyses of the sediment was correlated with changes in plume composition. Total sediment carbon content was generally low (rates in laboratory incubations, which ranged from 11.6 to 44.7 nmol (g dry wt)− 1 day− 1. Total water extractable organic carbon was groundwater velocity. This suggests that the total sorbed carbon pool is large relative to the rate of oxygen entrainment and will be impacting groundwater geochemistry for many decades. This has implications for long-term oxidation of reduced constituents, such as ammonium, that are being transported downgradient away from the infiltration beds toward surface and coastal discharge zones.

Modifications to ORIGEN2 for generating N Reactor source terms. Volume 3: ORIGEN2 N-Reactor output files

International Nuclear Information System (INIS)

1997-01-01

This text is intended to be a brief outline of the ORIGEN2 computer code which is a revised and updated version of the ORIGEN documented in report ORNL-4628 (May 1973). Included here are: a brief description of the functions of ORIGEN2; a listing of the major data sources; a listing of the published documentation concerning ORIGEN2; and an outline of the ORIGEN2 output organization. ORIGEN2 is available from the ORNL Radiation Shielding Information Center (RSIC). Past experience has indicated that many users encounter considerable difficulty in finding the desired information in a ORIGEN2 output which is sometimes rather massive. This section is intended as a brief outline of the organization of ORIGEN2 output

Source Term Characterization for Structural Components in 17 x 17 KOFA Spent Fuel Assembly

Energy Technology Data Exchange (ETDEWEB)

Cho, Dong Keun; Kook, Dong Hak; Choi, Heui Joo; Choi, Jong Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2010-12-15

Source terms of metal waste comprising a spent fuel assembly are relatively important when the spent fuel is pyroprocessed, because cesium, strontium, and transuranics are not a concern any more in the aspect of source term of permanent disposal. In this study, characteristics of radiation source terms for each structural component in spent fuel assembly was analyzed by using ORIGEN-S with a assumption that 10 metric tons of uranium is pyroprocessed. At first, mass and volume for each structural component of the fuel assembly were calculated in detail. Activation cross section library was generated by using KENO-VI/ORIGEN-S module for top-end piece and bottom-end piece, because those are located at outer core with different neutron spectrum compared to that of inner core. As a result, values of radioactivity, decay heat, and hazard index were reveled to be 1.40 x 10{sup 15} Bequerels, 236 Watts, 4.34 x 10{sup 9} m{sup 3}-water, respectively, at 10 years after discharge. Those values correspond to 0.7 %, 1.1 %, 0.1 %, respectively, compared to that of spent fuel. Inconel 718 grid plate was shown to be the most important component in the all aspects of radioactivity, decay heat, and hazard index although the mass occupies only 1 % of the total. It was also shown that if the Inconel 718 grid plate is managed separately, the radioactivity and hazard index of metal waste could be decreased to 20 {approx} 45 % and 30 {approx} 45 %, respectively. As a whole, decay heat of metal waste was shown to be negligible in the aspect of disposal system design, while the radioactivity and hazard index are important.

Title List of documents made publicly available

International Nuclear Information System (INIS)

1982-05-01

This document contains descriptions of the information received and generated by the US NRC. This information includes: (1) docketed material associated with civilian nuclear power plants and other uses of radioactive materials and (2) nondocketed material received and generated by NRC pertinent to its role as a regulatory agency. As used here, docketed does not refer to court dockets; it refers to the system by which NRC maintains its regulatory records. This series of documents is indexed by a Personal Author Index, a Corporate Source Index, and a Report Number Index

Renewable energy sources and Estonian national interests

International Nuclear Information System (INIS)

Veski, Rein

2002-01-01

There is only one national level document, The Long-term National Development Plan for the Fuel and Energy sector, regulating the development of renewable energy for Estonia. It was approved by the Parliament (Riigikogu) in 1998. This document planned a 2/3 (66,7%) increase in the share of renewable (according to the document: peat, biofuels and other renewables) to the year 2010 against 1996. At the same time a decrease of the share of domestic oil shale was planned 1/5 to the year 2010 against 1995. That means the use of domestic energy sources, both renewable and non-renewable, will decrease by 16,8% altogether. In reality the rapid projected growth of renewables in Estonia (+66,7% between 1996 and 2010) was changed with decrease of 20% by 2000. So the security of supply must shift to the first place in Estonia. It is also an issue of national sovereignty. Estonia is rich in renewable energy sources, mainly in wood, peat and wind, to achieve the goals set in the National Development Plan. Forest resources amount 352,7, total felling 6,44, allowed felling 7,81 million cubic meters solid volume in 2000. The future of fuel peat usage in Estonia is uncertain, as most of the EU member states, which have burned up their peat resources and/or drained their mires do not consider peat as a renewable fuel. Obviously Estonia has to explain its opinion about the renewability of its resources. Although progress is needed in all directions of additional use of all renewable energy sources in tactical consideration finance must be directed first to guarantee better use of wastes of woodworking and timber industry

"Restorative Justice": History of the Term's International and Danish Use

DEFF Research Database (Denmark)

Gade, Christian B. N.

2018-01-01

In this article, I explore the historical origin and development of the use of the term “restorative justice” in published sources. The main argument is that the growing popularity of the term and its expanding use makes increasingly blurred what restorative justice is. I begin by investigating....... In the 2000s, the term began to appear in United Nations and European Union documents, illustrating that restorative justice had become an internationally recognised approach to justice. After describing this international development, I analyse the Danish context, where the term “restorative justice” began...... to appear in writings around the year 2000. Around the same time, the existing Danish victim offender mediation programme became connected to restorative justice. Later, Danish practices outside the area of criminal justice became associated with the term. In conclusion, I argue that a potential problem...

Model description for calculating the source term of the Angra 1 environmental control system

International Nuclear Information System (INIS)

Oliveira, L.F.S. de; Amaral Neto, J.D.; Salles, M.R.

1988-01-01

This work presents the model used for evaluation of source term released from Angra 1 Nuclear Power Plant in case of an accident. After that, an application of the model for the case of a Fuel Assembly Drop Accident Inside the Fuel Handling Building during reactor refueling is presented. (author) [pt

Who has used internal company documents for biomedical and public health research and where did they find them?

Directory of Open Access Journals (Sweden)

L Susan Wieland

Full Text Available OBJECTIVE: To describe the sources of internal company documents used in public health and healthcare research. METHODS: We searched PubMed and Embase for articles using internal company documents to address a research question about a health-related topic. Our primary interest was where authors obtained internal company documents for their research. We also extracted information on type of company, type of research question, type of internal documents, and funding source. RESULTS: Our searches identified 9,305 citations of which 357 were eligible. Scanning of reference lists and consultation with colleagues identified 4 additional articles, resulting in 361 included articles. Most articles examined internal tobacco company documents (325/361; 90%. Articles using documents from pharmaceutical companies (20/361; 6% were the next most common. Tobacco articles used documents from repositories; pharmaceutical documents were from a range of sources. Most included articles relied upon internal company documents obtained through litigation (350/361; 97%. The research questions posed were primarily about company strategies to promote or position the company and its products (326/361; 90%. Most articles (346/361; 96% used information from miscellaneous documents such as memos or letters, or from unspecified types of documents. When explicit information about study funding was provided (290/361 articles, the most common source was the US-based National Cancer Institute. We developed an alternative and more sensitive search targeted at identifying additional research articles using internal pharmaceutical company documents, but the search retrieved an impractical number of citations for review. CONCLUSIONS: Internal company documents provide an excellent source of information on health topics (e.g., corporate behavior, study data exemplified by articles based on tobacco industry documents. Pharmaceutical and other industry documents appear to have been

Calculation of the isotope concentrations, source terms and radiation shielding of the SAFARI-1 irradiation products

International Nuclear Information System (INIS)

Stoker, C.C.; Ball, G.

2000-01-01

The ever increasing expansion of the irradiation product portfolio of the SAFARI-1 reactor leads to the need to routinely calculate the radio-isotope concentrations and source terms for the materials irradiated in the reactor accurately. In addition to this, the required shielding for the transportation and processing of these irradiation products needs to be determined. In this paper the calculational methodology applied is described with special attention given to the spectrum dependence of the one-group cross sections of selected SAFARI-1 irradiation materials and the consequent effect on the determination of the isotope concentrations and source terms. Comparisons of the calculated isotopic concentrations and dose rates with experimental analysis and measurements provide confidence in the calculational methodologies and data used. (author)

Lysimeter data as input to performance assessment source term codes

International Nuclear Information System (INIS)

McConnell, J.W. Jr.; Rogers, R.D.; Sullivan, T.

1992-01-01

The Field Lysimeter Investigation: Low-Level Waste Data Base Development Program is obtaining information on the performance of radioactive waste in a disposal environment. Waste forms fabricated using ion-exchange resins from EPICOR-II c prefilters employed in the cleanup of the Three Mile Island (TMI) Nuclear Power Station are being tested to develop a low-level waste data base and to obtain information on survivability of waste forms in a disposal environment. In this paper, radionuclide releases from waste forms in the first seven years of sampling are presented and discussed. Application of lysimeter data to be used in performance assessment source term models is presented. Initial results from use of data in two models are discussed

ON EXPERIENCE OF THE ELECTRONIC DOCUMENT MANAGEMENT SYSTEM IMPLEMENTATION IN THE MEDICAL UNIVERSITY

OpenAIRE

A. V. Semenets; V. Yu. Kovalok

2015-01-01

An importance of the application of the electronic document management to the Ukraine healthcare is shown. The electronic document management systems market overview is presented. Example of the usage of the open-source electronic document management system in the Ternopil State Medical University by I. Ya. Horbachevsky is shown. The implementation capabilities of the electronic document management system within a cloud services are shown. The electronic document management features of the Mi...

GPC Single Source Letter

Science.gov (United States)

This document may be of assistance in applying the New Source Review (NSR) air permitting regulations including the Prevention of Significant Deterioration (PSD) requirements. This document is part of the NSR Policy and Guidance Database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

Life Cycle Management Considerations of Remotely Sensed Geospatial Data and Documentation for Long Term Preservation

Science.gov (United States)

Khayat, Mohammad G.; Kempler, Steven J.

2015-01-01

As geospatial missions age, one of the challenges for the usability of data is the availability of relevant and updated metadata with sufficient documentation that can be used by future generations of users to gain knowledge from the original data. Given that remote sensing data undergo many intermediate processing steps, for example, an understanding of the exact algorithms employed and the quality of that data produced, could be key considerations for these users. As interest in global climate data is increasing, documentation about older data, their origins, and provenance are valuable to first time users attempting to perform historical climate research or comparative analysis of global change. Incomplete or missing documentation could be what stands in the way of a new researcher attempting to use the data. Therefore, preservation of documentation and related metadata is sometimes just as critical as the preservation of the original observational data. The Goddard Earth Sciences - Data and Information Service Center (GES DISC), a NASA Earth science Distributed Active Archive Center (DAAC), that falls under the management structure of the Earth Science Data and Information System (ESDIS), is actively pursuing the preservation of all necessary artifacts needed by future users. In this paper we will detail the data custodial planning and the data lifecycle process developed for content preservation, our implementation of a Preservation System to safeguard documents and associated artifacts from legacy (older) missions, as well as detail lessons learned regarding access rights and confidentiality of information issues. We also elaborate on key points that made our preservation effort successful; the primary points being: the drafting of a governing baseline for historical data preservation from satellite missions, and using the historical baseline as a guide to content filtering of what documents to preserve. The Preservation System currently archives

Environmental Restoration Remedial Action quality assurance requirements document

International Nuclear Information System (INIS)

1991-01-01

This document defines the quality assurance requirements for the US Department of Energy-Richland Operations Office Environmental Restoration Remedial Action program at the Hanford Site. The Environmental Restoration Remedial Action program implements significant commitments made by the US Department of Energy in the Hanford Federal Facility Agreement and Consent Order entered into with the Washington State Department of Ecology and the US Environmental Protection Agency. This document combines quality assurance requirements from various source documents into one set of requirements for use by the US Department of Energy-Richland Operations Office and other Environmental Restoration Remedial Action program participants. This document will serve as the basis for developing Quality Assurance Program Plans and implementing procedures by the participants. The requirements of this document will be applied to activities affecting quality, using a graded approach based on the importance of the item, service, or activity to the program objectives. The Quality Assurance Program that will be established using this document as the basis, together with other program and technical documents, form an integrated management control system for conducting the Environmental Restoration Remedial Action program activities in a manner that provides safety and protects the environment and public health

Annotated bibliography National Environmental Policy Act (NEPA) documents for Sandia National Laboratories

International Nuclear Information System (INIS)

Harris, J.M.

1995-04-01

The following annotated bibliography lists documents prepared by the Department of Energy (DOE), and predecessor agencies, to meet the requirements of the National Environmental Policy Act (NEPA) for activities and facilities at Sandia National Laboratories sites. For each NEPA document summary information and a brief discussion of content is provided. This information may be used to reduce the amount of time or cost associated with NEPA compliance for future Sandia National Laboratories projects. This summary may be used to identify model documents, documents to use as sources of information, or documents from which to tier additional NEPA documents

Annotated bibliography National Environmental Policy Act (NEPA) documents for Sandia National Laboratories

Energy Technology Data Exchange (ETDEWEB)

Harris, J.M.

1995-04-01

The following annotated bibliography lists documents prepared by the Department of Energy (DOE), and predecessor agencies, to meet the requirements of the National Environmental Policy Act (NEPA) for activities and facilities at Sandia National Laboratories sites. For each NEPA document summary information and a brief discussion of content is provided. This information may be used to reduce the amount of time or cost associated with NEPA compliance for future Sandia National Laboratories projects. This summary may be used to identify model documents, documents to use as sources of information, or documents from which to tier additional NEPA documents.

Guidelines for the calibration of low energy photon sources at beta-ray brachytherapy sources

International Nuclear Information System (INIS)

2000-01-01

With the development of improved methods of implanting brachytherapy sources in a precise manner for treating prostate cancer and other disease processes, there has been a tremendous growth in the use of low energy photon sources, such as 125 I and 103 Pd brachytherapy seeds. Low energy photon sources have the advantage of easier shielding and also lowering the dose to normal tissue. However, the dose distributions around these sources are affected by the details in construction of the source and its encapsulation more than other sources used for brachytherapy treatments, such as 192 Ir. With increasing number of new low energy photon sources on the market, care should be taken with regard to its traceability to primary standards. It cannot be assumed that a calibration factor for an ionization chamber that is valid for one type of low energy photon source, automatically is valid for another source even if both would use the same isotope. Moreover, the method used to calculate the dose must also take into account the structure of the source and the encapsulation. The dose calculation algorithm that is valid for one type of low energy source may not be valid for another source even if in both cases the same radionuclide is used. Simple ''point source'' approximations, i.e. where the source is modeled as a point, should be avoided, as such methods do not account for any details in the source construction. In this document, the dose calculation formalism adopted for low energy photon sources is that recommended by the American Association of Physicists in Medicine (AAPM) as outlined by Task Group-43 (TG-43). This method accounts for the source and capsule geometry. The AAPM recommends brachytherapy photon sources to be specified in terms of 'Air Kerma Strength' that is also used in the formalism mentioned above. On the other hand, the International Commission on Radiation Units and Measurements (ICRU) recommends that the specification be done in terms of Reference Air

A source term and risk calculations using level 2+PSA methodology

International Nuclear Information System (INIS)

Park, S. I.; Jea, M. S.; Jeon, K. D.

2002-01-01

The scope of Level 2+ PSA includes the assessment of dose risk which is associated with the exposures of the radioactive nuclides escaping from nuclear power plants during severe accidents. The establishment of data base for the exposure dose in Korea nuclear power plants may contribute to preparing the accident management programs and periodic safety reviews. In this study the ORIGEN, MELCOR and MACCS code were employed to produce a integrated framework to assess the radiation source term risk. The framework was applied to a reference plant. Using IPE results, the dose rate for the reference plant was calculated quantitatively

The SSI TOOLBOX Source Term Model SOSIM - Screening for important radionuclides and parameter sensitivity analysis

Energy Technology Data Exchange (ETDEWEB)

Avila Moreno, R.; Barrdahl, R.; Haegg, C.

1995-05-01

The main objective of the present study was to carry out a screening and a sensitivity analysis of the SSI TOOLBOX source term model SOSIM. This model is a part of the SSI TOOLBOX for radiological impact assessment of the Swedish disposal concept for high-level waste KBS-3. The outputs of interest for this purpose were: the total released fraction, the time of total release, the time and value of maximum release rate, the dose rates after direct releases of the biosphere. The source term equations were derived and simple equations and methods were proposed for calculation of these. A literature survey has been performed in order to determine a characteristic variation range and a nominal value for each model parameter. In order to reduce the model uncertainties the authors recommend a change in the initial boundary condition for solution of the diffusion equation for highly soluble nuclides. 13 refs.

Basic repository source term and data sheet report, Cypress Creek Dome: Draft

International Nuclear Information System (INIS)

1988-01-01

This report is one of a series describing studies undertaken in support of the US Department of Energy Civilian Radioactive Waste Management (CRWM) Program. This study contains the derivation of values for environmental source terms and resources consumed for a CRWM repository. Estimates include heavy construction equipment; support equipment; shaft-sinking equipment; transportation equipment; and consumption of fuel, water, electricity, and natural gas. Data are presented for construction and operation at an assumed site in Cypress Creek Dome, Mississippi. 2 refs., 6 tabs

Optimization method for identifying the source term in an inverse wave equation

Directory of Open Access Journals (Sweden)

Arumugam Deiveegan

2017-08-01

Full Text Available In this work, we investigate the inverse problem of identifying a space-wise dependent source term of wave equation from the measurement on the boundary. On the basis of the optimal control framework, the inverse problem is transformed into an optimization problem. The existence and necessary condition of the minimizer for the cost functional are obtained. The projected gradient method and two-parameter model function method are applied to the minimization problem and numerical results are illustrated.

The MIT/OSO 7 catalog of X-ray sources - Intensities, spectra, and long-term variability

Science.gov (United States)

Markert, T. H.; Laird, F. N.; Clark, G. W.; Hearn, D. R.; Sprott, G. F.; Li, F. K.; Bradt, H. V.; Lewin, W. H. G.; Schnopper, H. W.; Winkler, P. F.

1979-01-01

This paper is a summary of the observations of the cosmic X-ray sky performed by the MIT 1-40-keV X-ray detectors on OSO 7 between October 1971 and May 1973. Specifically, mean intensities or upper limits of all third Uhuru or OSO 7 cataloged sources (185 sources) in the 3-10-keV range are computed. For those sources for which a statistically significant (greater than 20) intensity was found in the 3-10-keV band (138 sources), further intensity determinations were made in the 1-15-keV, 1-6-keV, and 15-40-keV energy bands. Graphs and other simple techniques are provided to aid the user in converting the observed counting rates to convenient units and in determining spectral parameters. Long-term light curves (counting rates in one or more energy bands as a function of time) are plotted for 86 of the brighter sources.

Delirium in palliative care: Detection, documentation and management in three settings.

Science.gov (United States)

Hey, Jennifer; Hosker, Christian; Ward, Jason; Kite, Suzanne; Speechley, Helen

2015-12-01

Delirium is characterized by disturbances of consciousness and changes in cognition that develop rapidly and fluctuate. It is common in palliative care, affecting up to 88% of patients with advanced cancer, yet often remains insufficiently diagnosed and managed. This study sought to compare rates of screening, documentation, and management of delirium across three palliative care settings - two hospices and one hospital team - and to determine whether definitive documentation of delirium as a diagnosis is associated with improved management of the disorder. A retrospective review of patient case notes was performed in three U.K. palliative care settings for the presence of: cognitive screening tools on first assessment; the term "delirium" as a stated documented diagnosis; documented terms, descriptions, and synonyms suggestive of delirium; and management plans aimed at addressing delirium. We reviewed 319 notes. The prevalence of delirium as a documented diagnosis ranged from 0 to 8.4%, rising to 35.7-39.2% when both documented delirium and descriptions suggestive of delirium were taken into account. An abbreviated mental test score (AMTS) was determined for 19.6 (H1) and 26.8% (H2) of hospice admissions and for 0% of hospital assessments. Symptoms suggestive of delirium were managed in 56.3% of cases in hospital, compared with 66.7 (H1) and 72.2% (H2) in hospices. Use of the term "delirium" was infrequent in both hospital and hospice palliative care settings, as was the use of routine screening. Many identified cases did not receive targeted management. The definitive use of the term as a diagnosis was associated with clearer management plans in hospital patients. The authors suggest that better screening and identification remains the first step in improving delirium management.

Toward a Mechanistic Source Term in Advanced Reactors: Characterization of Radionuclide Transport and Retention in a Sodium Cooled Fast Reactor

Energy Technology Data Exchange (ETDEWEB)

Brunett, Acacia J.; Bucknor, Matthew; Grabaskas, David

2016-04-17

A vital component of the U.S. reactor licensing process is an integrated safety analysis in which a source term representing the release of radionuclides during normal operation and accident sequences is analyzed. Historically, source term analyses have utilized bounding, deterministic assumptions regarding radionuclide release. However, advancements in technical capabilities and the knowledge state have enabled the development of more realistic and best-estimate retention and release models such that a mechanistic source term assessment can be expected to be a required component of future licensing of advanced reactors. Recently, as part of a Regulatory Technology Development Plan effort for sodium cooled fast reactors (SFRs), Argonne National Laboratory has investigated the current state of knowledge of potential source terms in an SFR via an extensive review of previous domestic experiments, accidents, and operation. As part of this work, the significant sources and transport processes of radionuclides in an SFR have been identified and characterized. This effort examines all stages of release and source term evolution, beginning with release from the fuel pin and ending with retention in containment. Radionuclide sources considered in this effort include releases originating both in-vessel (e.g. in-core fuel, primary sodium, cover gas cleanup system, etc.) and ex-vessel (e.g. spent fuel storage, handling, and movement). Releases resulting from a primary sodium fire are also considered as a potential source. For each release group, dominant transport phenomena are identified and qualitatively discussed. The key product of this effort was the development of concise, inclusive diagrams that illustrate the release and retention mechanisms at a high level, where unique schematics have been developed for in-vessel, ex-vessel and sodium fire releases. This review effort has also found that despite the substantial range of phenomena affecting radionuclide release, the

Refined Source Terms in WAVEWATCH III with Wave Breaking and Sea Spray Forecasts

Science.gov (United States)

2015-09-30

dissipation and breaking, nonlinear wave-wave interaction, bottom friction, wave-mud interaction, wave-current interaction as well as sea spray flux. These...shallow water outside the surf zone. After careful testing within a comprehensive suite of test bed cases, these refined source terms will be...aim to refine the parameterization of air-sea and upper ocean fluxes, including wind input and sea spray as well as dissipation, and hence improve

A Source Term Calculation for the APR1400 NSSS Auxiliary System Components Using the Modified SHIELD Code

International Nuclear Information System (INIS)

Park, Hong Sik; Kim, Min; Park, Seong Chan; Seo, Jong Tae; Kim, Eun Kee

2005-01-01

The SHIELD code has been used to calculate the source terms of NSSS Auxiliary System (comprising CVCS, SIS, and SCS) components of the OPR1000. Because the code had been developed based upon the SYSTEM80 design and the APR1400 NSSS Auxiliary System design is considerably changed from that of SYSTEM80 or OPR1000, the SHIELD code cannot be used directly for APR1400 radiation design. Thus the hand-calculation is needed for the portion of design changes using the results of the SHIELD code calculation. In this study, the SHIELD code is modified to incorporate the APR1400 design changes and the source term calculation is performed for the APR1400 NSSS Auxiliary System components

PRIMARY SCHOOL TEACHERS’ OPINIONS ABOUT THE CURRICULAR DOCUMENTS USED FOR STUDYING THE MATHEMATICS AND ENVIRONMENTAL EXPLORATION SUBJECT

Directory of Open Access Journals (Sweden)

Ioana-Cristina MAGDAȘ

2017-08-01

Full Text Available Due to the introduction in 2013 into the new Framework Plan for the primary education of the integrated Mathematics and Environmental Exploration (MEE subject, of new textbooks and auxiliaries, we considered it necessary to find the the teachers’ opinions regarding the way in which the curriculum documents facilitate the study of the MEE subject. The present article is based on a research performed using a survey carried out voluntarily and anonymously by 131 teachers for primary education. Through the responses to the questionnaire, we identified several important issues. Regarding teachers’ sources of documentation, we found out that they prefered online sources (websites, blogs and specialized forums, which was surprising because these sources did not have the reliability of correct information. Only on the next places were placed the official documents or those elaborated by specialists. Teachers assigned scores of about four (out of a maximum of five to the clarity of all components of the school curriculum. In terms of textbooks and auxiliaries, respondents scored better auxiliaries across all the indicators considered. The biggest benefit of introducing the MEE subject identified by I.-C. MAGDAȘ, M. E. DULAMĂ, O.-R. ILOVAN, I.C. CRIȘAN 6 respondents was that activities were more attractive or motivating for learning. At the opposite end, the smallest benefits related to ensuring the rigour and learning durability of both Mathematics and Environmental Exploration. Regarding the limitations, disadvantages or problems of studying the MEE subject, the lack of support materials was the first reported by the respondents. On the next places were placed the need for specific lessons with mathematical content or the heavy design of thematic units and lessons.

Running the source term code package in Elebra MX-850

International Nuclear Information System (INIS)

Guimaraes, A.C.F.; Goes, A.G.A.

1988-01-01

The source term package (STCP) is one of the main tools applied in calculations of behavior of fission products from nuclear power plants. It is a set of computer codes to assist the calculations of the radioactive materials leaving from the metallic containment of power reactors to the environment during a severe reactor accident. The original version of STCP runs in SDC computer systems, but as it has been written in FORTRAN 77, is possible run it in others systems such as IBM, Burroughs, Elebra, etc. The Elebra MX-8500 version of STCP contains 5 codes:March 3, Trapmelt, Tcca, Vanessa and Nava. The example presented in this report has taken into consideration a small LOCA accident into a PWR type reactor. (M.I.)

Guidance and Control Software Project Data - Volume 2: Development Documents

Science.gov (United States)

Hayhurst, Kelly J. (Editor)

2008-01-01

The Guidance and Control Software (GCS) project was the last in a series of software reliability studies conducted at Langley Research Center between 1977 and 1994. The technical results of the GCS project were recorded after the experiment was completed. Some of the support documentation produced as part of the experiment, however, is serving an unexpected role far beyond its original project context. Some of the software used as part of the GCS project was developed to conform to the RTCA/DO-178B software standard, "Software Considerations in Airborne Systems and Equipment Certification," used in the civil aviation industry. That standard requires extensive documentation throughout the software development life cycle, including plans, software requirements, design and source code, verification cases and results, and configuration management and quality control data. The project documentation that includes this information is open for public scrutiny without the legal or safety implications associated with comparable data from an avionics manufacturer. This public availability has afforded an opportunity to use the GCS project documents for DO-178B training. This report provides a brief overview of the GCS project, describes the 4-volume set of documents and the role they are playing in training, and includes the development documents from the GCS project. Volume 2 contains three appendices: A. Guidance and Control Software Development Specification; B. Design Description for the Pluto Implementation of the Guidance and Control Software; and C. Source Code for the Pluto Implementation of the Guidance and Control Software

Who Has Used Internal Company Documents for Biomedical and Public Health Research and Where Did They Find Them?

OpenAIRE

Wieland, L. Susan; Rutkow, Lainie; Vedula, S. Swaroop; Kaufmann, Christopher N.; Rosman, Lori M.; Twose, Claire; Mahendraratnam, Nirosha; Dickersin, Kay

2014-01-01

OBJECTIVE: To describe the sources of internal company documents used in public health and healthcare research. METHODS: We searched PubMed and Embase for articles using internal company documents to address a research question about a health-related topic. Our primary interest was where authors obtained internal company documents for their research. We also extracted information on type of company, type of research question, type of internal documents, and funding source. RESULTS: Our search...

Guide for the realization of Design Base Documents (DBD)

International Nuclear Information System (INIS)

Roca Mallofre, G. la

2010-01-01

Guide for improving the consistency and quality content of the Design Base Documents. It's a short description of how to carry out and complete these Documents but focusing on those aspects that can be more confusing and harder to interpret. This guide aims to clarify the term Design Base distinguishing between production and safety, and it focuses on safety Design Base Documents and their values and references. It also emphasizes the difference between the support system and the interface system when there is a functional connection between different systems.

Recommendations: Introducing the quality system into the use of significant ionizing radiation sources in radiotherapy. Radionuclide irradiators

International Nuclear Information System (INIS)

2003-01-01

The document is a recommendation which sums up requirements of the State Office for Nuclear Safety of the Czech Republic, IEC and EN Standards and recommendations of the Czech Society for Radiation Oncology, Biology and Physics applicable to radionuclide sources used in radiotherapy in the Czech Republic. This document should serve as a tool when developing Quality Assurance programmes, particularly for operating and long-term stability tests. Described are the procedure to inspect the parameter in question, evaluation of results and frequency of parameter inspections. (P.A.)

Source terms associated with two severe accident sequences in a 900 MWe PWR

International Nuclear Information System (INIS)

Fermandjian, J.; Evrard, J.M.; Berthion, Y.; Lhiaubet, G.; Lucas, M.

1983-12-01

Hypothetical accidents taken into account in PWR risk assessment result in fission product release from the fuel, transfer through the primary circuit, transfer into the reactor containment building (RCB) and finally release to the environment. The objective of this paper is to define the characteristics of the source term (noble gases, particles and volatile iodine forms) released from the reactor containment building during two dominant core-melt accident sequences: S 2 CD and TLB according to the ''Reactor Safety Study'' terminology. The reactor chosen for this study is a French 900 MWe PWR unit. The reactor building is a prestressed concrete containment with an internal liner. The first core-melt accident sequence is a 2-break loss-of-coolant accident on the cold leg, with failure of both system and the containment spray system. The second one is a transient initiated by a loss of offsite and onsite power supply and auxiliary feedwater system. These two sequences have been chosen because they are representative of risk dominant scenarios. Source terms associated with hypothetical core-melt accidents S 2 CD and TLB in a French PWR -900 MWe- have been performed using French computer codes (in particular, JERICHO Code for containment response analysis and AEROSOLS/31 for aerosol behavior in the containment)

Source term evaluation model for high-level radioactive waste repository with decay chain build-up.

Science.gov (United States)

Chopra, Manish; Sunny, Faby; Oza, R B

2016-09-18

A source term model based on two-component leach flux concept is developed for a high-level radioactive waste repository. The long-lived radionuclides associated with high-level waste may give rise to the build-up of activity because of radioactive decay chains. The ingrowths of progeny are incorporated in the model using Bateman decay chain build-up equations. The model is applied to different radionuclides present in the high-level radioactive waste, which form a part of decay chains (4n to 4n + 3 series), and the activity of the parent and daughter radionuclides leaching out of the waste matrix is estimated. Two cases are considered: one when only parent is present initially in the waste and another where daughters are also initially present in the waste matrix. The incorporation of in situ production of daughter radionuclides in the source is important to carry out realistic estimates. It is shown that the inclusion of decay chain build-up is essential to avoid underestimation of the radiological impact assessment of the repository. The model can be a useful tool for evaluating the source term of the radionuclide transport models used for the radiological impact assessment of high-level radioactive waste repositories.

Radiological Source Terms for Tank Farms Safety Analysis

Energy Technology Data Exchange (ETDEWEB)

COWLEY, W.L.

2000-06-27

This document provides Unit Liter Dose factors, atmospheric dispersion coefficients, breathing rates and instructions for using and customizing these factors for use in calculating radiological doses for accident analyses in the Hanford Tank Farms.

Title list of documents made publicly available, July 1-31, 1979