WorldWideScience

Sample records for source term initial

  1. Atucha-I source terms for sequences initiated by transients

    International Nuclear Information System (INIS)

    Baron, J.; Bastianelli, B.

    1997-01-01

    The present work is part of an expected source terms study in the Atucha I nuclear power plant during severe accidents. From the accident sequences with a significant probability to produce core damage, those initiated by operational transients have been identified as the most relevant. These sequences have some common characteristics, in the sense that all of them resume in the opening of the primary system safety valves, and leave this path open for the coolant loss. In the case these sequences continue as severe accidents, the same path will be used for the release of the radionuclides, from the core, through the primary system and to the containment. Later in the severe accident sequence, the failure of the pressure vessel will occur, and the corium will fall inside the reactor cavity, interacting with the concrete. During these processes, more radioactive products will be released inside the containment. In the present work the severe accident simulation initiated by a blackout is performed, from the point of view of the phenomenology of the behavior of the radioactive products, as they are transported in the piping, during the core-concrete interactions, and inside the containment buildings until it failure. The final result is the source term into the atmosphere. (author) [es

  2. ITER Safety Task NID-5A, Subtask 1-1: Source terms and energies - initial tritium source terms. Final report

    International Nuclear Information System (INIS)

    Fong, C.; Kalyanam, K.M.; Tanaka, M.R.; Sood, S.; Natalizio, A.; Delisle, M.

    1995-02-01

    The overall objective of the Early Safety and Environmental Characterization Study (ESECS) is to assess the environmental impact of tritium using appropriate assumptions on a hypothetical site for ITER, having the r eference s ite characteristics as proposed by the JCT. The objective of this work under the above subtask 1-1, NID-5a, is to determine environmental source terms (i.e., process source term x containment release fraction) for the fuel cycle and cooling systems. The work is based on inventories and process source terms (i.e., inventory x mobilization fraction), provided by others (under Task NID 3b). The results of this work form the basis for the determination, by others, of the off-site dose (i.e., environmental source term x dose/release ratio). For the determination of the environmental source terms, the TMAP4 code has been utilized (ref 1). This code is approved by ITER for safety assessment. Volume 3 is a compilation of appendices giving detailed results of the study

  3. ITER Safety Task NID-5A, Subtask 1-1: Source terms and energies - initial tritium source terms. Final report

    International Nuclear Information System (INIS)

    Fong, C.; Kalyanam, K.M.; Tanaka, M.R.; Sood, S.; Natalizio, A.; Delisle, M.

    1995-02-01

    The overall objective of the Early Safety and Environmental Characterization Study (ESECS) is to assess the environmental impact of tritium using appropriate assumptions on a hypothetical site for ITER, having the r eference s ite characteristics as proposed by the JCT. The objective of this work under the above subtask 1-1, NID-5a, is to determine environmental source terms (i.e., process source term x containment release fraction) for the fuel cycle and cooling systems. The work is based on inventories and process source terms (i.e., inventory x mobilization fraction), provided by others (under Task NID 3b). The results of this work form the basis for the determination, by others, of the off-site dose (i.e., environmental source term x dose/release ratio). For the determination of the environmental source terms, the TMAP4 code has been utilized (ref 1). This code is approved by ITER for safety assessment. 6 refs

  4. ITER Safety Task NID-5A, Subtask 1-1: Source terms and energies - initial tritium source terms. Final report

    International Nuclear Information System (INIS)

    Fong, C.; Kalyanam, K.M.; Tanaka, M.R.; Sood, S.; Natalizio, A.; Delisle, M.

    1995-02-01

    The overall objective of the Early Safety and Environmental Characterization Study (ESECS) is to assess the environmental impact of tritium using appropriate assumptions on a hypothetical site for ITER, having the r eference s ite characteristics as proposed by the JCT. The objective of this work under the above subtask 1-1, NID-5a, is to determine environmental source terms (i.e., process source term x containment release fraction) for the fuel cycle and cooling systems. The work is based on inventories and process source terms (i.e., inventory x mobilization fraction), provided by others (under Task NID 3b). The results of this work form the basis for the determination, by others, of the off-site dose (i.e., environmental source term x dose/release ratio). For the determination of the environmental source terms, the TMAP4 code has been utilized (ref 1). This code is approved by ITER for safety assessment. Volume 2 is a compilation of appendices giving detailed results of the study. 5 figs

  5. Reassessment of the technical bases for estimating source terms. Final report

    International Nuclear Information System (INIS)

    Silberberg, M.; Mitchell, J.A.; Meyer, R.O.; Ryder, C.P.

    1986-07-01

    This document describes a major advance in the technology for calculating source terms from postulated accidents at US light-water reactors. The improved technology consists of (1) an extensive data base from severe accident research programs initiated following the TMI accident, (2) a set of coupled and integrated computer codes (the Source Term Code Package), which models key aspects of fission product behavior under severe accident conditions, and (3) a number of detailed mechanistic codes that bridge the gap between the data base and the Source Term Code Package. The improved understanding of severe accident phenonmena has also allowed an identification of significant sources of uncertainty, which should be considered in estimating source terms. These sources of uncertainty are also described in this document. The current technology provides a significant improvement in evaluating source terms over that available at the time of the Reactor Safety Study (WASH-1400) and, because of this significance, the Nuclear Regulatory Commission staff is recommending its use

  6. Fission-product source terms

    International Nuclear Information System (INIS)

    Lorenz, R.A.

    1981-01-01

    This presentation consists of a review of fission-product source terms for light water reactor (LWR) fuel. A source term is the quantity of fission products released under specified conditions that can be used to calculate the consequences of the release. The source term usually defines release from breached fuel-rod cladding but could also describe release from the primary coolant system, the reactor containment shell, or the site boundary. The source term would be different for each locality, and the chemical and physical forms of the fission products could also differ

  7. 19 CFR 10.532 - Integrated Sourcing Initiative.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Integrated Sourcing Initiative. 10.532 Section 10... Trade Agreement Rules of Origin § 10.532 Integrated Sourcing Initiative. (a) For purposes of General... Sourcing Initiative if: (1) The good, in its condition as imported, is both classified in a tariff...

  8. Design parameters and source terms: Volume 3, Source terms

    International Nuclear Information System (INIS)

    1987-10-01

    The Design Parameters and Source Terms Document was prepared in accordance with DOE request and to provide data for the environmental impact study to be performed in the future for the Deaf Smith County, Texas site for a nuclear waste repository in salt. This document updates a previous unpublished report by Stearns Catalytic Corporation (SCC), entitled ''Design Parameters and Source Terms for a Two-Phase Repository in Salt,'' 1985, to the level of the Site Characterization Plan - Conceptual Design Report. The previous unpublished SCC Study identifies the data needs for the Environmental Assessment effort for seven possible Salt Repository sites. 11 refs., 9 tabs

  9. Application of the source term code package to obtain a specific source term for the Laguna Verde Nuclear Power Plant

    International Nuclear Information System (INIS)

    Souto, F.J.

    1991-06-01

    The main objective of the project was to use the Source Term Code Package (STCP) to obtain a specific source term for those accident sequences deemed dominant as a result of probabilistic safety analyses (PSA) for the Laguna Verde Nuclear Power Plant (CNLV). The following programme has been carried out to meet this objective: (a) implementation of the STCP, (b) acquisition of specific data for CNLV to execute the STCP, and (c) calculations of specific source terms for accident sequences at CNLV. The STCP has been implemented and validated on CDC 170/815 and CDC 180/860 main frames as well as on a Micro VAX 3800 system. In order to get a plant-specific source term, data on the CNLV including initial core inventory, burn-up, primary containment structures, and materials used for the calculations have been obtained. Because STCP does not explicitly model containment failure, dry well failure in the form of a catastrophic rupture has been assumed. One of the most significant sequences from the point of view of possible off-site risk is the loss of off-site power with failure of the diesel generators and simultaneous loss of high pressure core spray and reactor core isolation cooling systems. The probability for that event is approximately 4.5 x 10 -6 . This sequence has been analysed in detail and the release fractions of radioisotope groups are given in the full report. 18 refs, 4 figs, 3 tabs

  10. Spallation Neutron Source Accident Terms for Environmental Impact Statement Input

    Energy Technology Data Exchange (ETDEWEB)

    Devore, J.R.; Harrington, R.M.

    1998-08-01

    This report is about accidents with the potential to release radioactive materials into the environment surrounding the Spallation Neutron Source (SNS). As shown in Chap. 2, the inventories of radioactivity at the SNS are dominated by the target facility. Source terms for a wide range of target facility accidents, from anticipated events to worst-case beyond-design-basis events, are provided in Chaps. 3 and 4. The most important criterion applied to these accident source terms is that they should not underestimate potential release. Therefore, conservative methodology was employed for the release estimates. Although the source terms are very conservative, excessive conservatism has been avoided by basing the releases on physical principles. Since it is envisioned that the SNS facility may eventually (after about 10 years) be expanded and modified to support a 4-MW proton beam operational capability, the source terms estimated in this report are applicable to a 4-MW operating proton beam power unless otherwise specified. This is bounding with regard to the 1-MW facility that will be built and operated initially. See further discussion below in Sect. 1.2.

  11. Recovering the source and initial value simultaneously in a parabolic equation

    International Nuclear Information System (INIS)

    Zheng, Guang-Hui; Wei, Ting

    2014-01-01

    In this paper, we consider an inverse problem to simultaneously reconstruct the source term and initial data associated with a parabolic equation based on the additional temperature data at a terminal time t = T and the temperature data on an accessible part of a boundary. The conditional stability and uniqueness of the inverse problem are established. We apply a variational regularization method to recover the source and initial value. The existence, uniqueness and stability of the minimizer of the corresponding variational problem are obtained. Taking the minimizer as a regularized solution for the inverse problem, under an a priori and an a posteriori parameter choice rule, the convergence rates of the regularized solution under a source condition are also given. Furthermore, the source condition is characterized by an optimal control approach. Finally, we use a conjugate gradient method and a stopping criterion given by Morozov's discrepancy principle to solve the variational problem. Numerical experiments are provided to demonstrate the feasibility of the method. (papers)

  12. Design parameters and source terms: Volume 2, Source terms: Revision 0

    International Nuclear Information System (INIS)

    1987-09-01

    The Design Parameters and Source Terms Document was prepared in accordance with DOE request and to provide data for the environmental impact study to be performed in the future for the Deaf Smith County, Texas site for a nuclear waste repository in salt. This document updates a previous unpublished report to the level of the Site Characterization Plan---Conceptual Design Report SCP-CDR. The previous study identifies the data needs for the Environmental Assessment effort for seven possible salt repository sites. Volume 2 contains tables of source terms

  13. A Study on Improvement of Algorithm for Source Term Evaluation

    International Nuclear Information System (INIS)

    Park, Jeong Ho; Park, Do Hyung; Lee, Jae Hee

    2010-03-01

    The program developed by KAERI for source term assessment of radwastes from the advanced nuclear fuel cycle consists of spent fuel database analysis module, spent fuel arising projection module, and automatic characterization module for radwastes from pyroprocess. To improve the algorithm adopted the developed program, following items were carried out: - development of an algorithm to decrease analysis time for spent fuel database - development of setup routine for a analysis procedure - improvement of interface for spent fuel arising projection module - optimization of data management algorithm needed for massive calculation to estimate source terms of radwastes from advanced fuel cycle The program developed through this study has a capability to perform source term estimation although several spent fuel assemblies with different fuel design, initial enrichment, irradiation history, discharge burnup, and cooling time are processed at the same time in the pyroprocess. It is expected that this program will be very useful for the design of unit process of pyroprocess and disposal system

  14. Design parameters and source terms: Volume 2, Source terms: Revision 0

    International Nuclear Information System (INIS)

    1987-10-01

    The Design Parameters and Source Terms Document was prepared in accordance with DOE request and to provide data for the environmental impact study to be performed in the future for the Deaf Smith County, Texas site for a nuclear waste repository in salt. This document updates a previous unpublished report by Stearns Catalytic Corporation (SCC), entitled ''Design Parameters and Source Terms for a Two-Phase Repository Salt,'' 1985, to the level of the Site Characterization Plan - Conceptual Design Report. The previous unpublished SCC Study identifies the data needs for the Environmental Assessment effort for seven possible Salt Repository sites. 2 tabs

  15. SOURCE TERMS FOR HLW GLASS CANISTERS

    International Nuclear Information System (INIS)

    J.S. Tang

    2000-01-01

    This calculation is prepared by the Monitored Geologic Repository (MGR) Waste Package Design Section. The objective of this calculation is to determine the source terms that include radionuclide inventory, decay heat, and radiation sources due to gamma rays and neutrons for the high-level radioactive waste (HLW) from the, West Valley Demonstration Project (WVDP), Savannah River Site (SRS), Hanford Site (HS), and Idaho National Engineering and Environmental Laboratory (INEEL). This calculation also determines the source terms of the canister containing the SRS HLW glass and immobilized plutonium. The scope of this calculation is limited to source terms for a time period out to one million years. The results of this calculation may be used to carry out performance assessment of the potential repository and to evaluate radiation environments surrounding the waste packages (WPs). This calculation was performed in accordance with the Development Plan ''Source Terms for HLW Glass Canisters'' (Ref. 7.24)

  16. 10 CFR 50.67 - Accident source term.

    Science.gov (United States)

    2010-01-01

    ... Conditions of Licenses and Construction Permits § 50.67 Accident source term. (a) Applicability. The... 10 Energy 1 2010-01-01 2010-01-01 false Accident source term. 50.67 Section 50.67 Energy NUCLEAR... to January 10, 1997, who seek to revise the current accident source term used in their design basis...

  17. ITER safety task NID-5a: ITER tritium environmental source terms - safety analysis basis

    International Nuclear Information System (INIS)

    Natalizio, A.; Kalyanam, K.M.

    1994-09-01

    The Canadian Fusion Fuels Technology Project's (CFFTP) is part of the contribution to ITER task NID-5a, Initial Tritium Source Term. This safety analysis basis constitutes the first part of the work for establishing tritium source terms and is intended to solicit comments and obtain agreement. The analysis objective is to provide an early estimate of tritium environmental source terms for the events to be analyzed. Events that would result in the loss of tritium are: a Loss of Coolant Accident (LOCA), a vacuum vessel boundary breach. a torus exhaust line failure, a fuelling machine process boundary failure, a fuel processing system process boundary failure, a water detritiation system process boundary failure and an isotope separation system process boundary failure. 9 figs

  18. New Source Term Model for the RESRAD-OFFSITE Code Version 3

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Charley [Argonne National Lab. (ANL), Argonne, IL (United States); Gnanapragasam, Emmanuel [Argonne National Lab. (ANL), Argonne, IL (United States); Cheng, Jing-Jy [Argonne National Lab. (ANL), Argonne, IL (United States); Kamboj, Sunita [Argonne National Lab. (ANL), Argonne, IL (United States); Chen, Shih-Yew [Argonne National Lab. (ANL), Argonne, IL (United States)

    2013-06-01

    This report documents the new source term model developed and implemented in Version 3 of the RESRAD-OFFSITE code. This new source term model includes: (1) "first order release with transport" option, in which the release of the radionuclide is proportional to the inventory in the primary contamination and the user-specified leach rate is the proportionality constant, (2) "equilibrium desorption release" option, in which the user specifies the distribution coefficient which quantifies the partitioning of the radionuclide between the solid and aqueous phases, and (3) "uniform release" option, in which the radionuclides are released from a constant fraction of the initially contaminated material during each time interval and the user specifies the duration over which the radionuclides are released.

  19. Calculation of source terms for NUREG-1150

    International Nuclear Information System (INIS)

    Breeding, R.J.; Williams, D.C.; Murfin, W.B.; Amos, C.N.; Helton, J.C.

    1987-10-01

    The source terms estimated for NUREG-1150 are generally based on the Source Term Code Package (STCP), but the actual source term calculations used in computing risk are performed by much smaller codes which are specific to each plant. This was done because the method of estimating the uncertainty in risk for NUREG-1150 requires hundreds of source term calculations for each accident sequence. This is clearly impossible with a large, detailed code like the STCP. The small plant-specific codes are based on simple algorithms and utilize adjustable parameters. The values of the parameters appearing in these codes are derived from the available STCP results. To determine the uncertainty in the estimation of the source terms, these parameters were varied as specified by an expert review group. This method was used to account for the uncertainties in the STCP results and the uncertainties in phenomena not considered by the STCP

  20. Subsurface Shielding Source Term Specification Calculation

    International Nuclear Information System (INIS)

    S.Su

    2001-01-01

    The purpose of this calculation is to establish appropriate and defensible waste-package radiation source terms for use in repository subsurface shielding design. This calculation supports the shielding design for the waste emplacement and retrieval system, and subsurface facility system. The objective is to identify the limiting waste package and specify its associated source terms including source strengths and energy spectra. Consistent with the Technical Work Plan for Subsurface Design Section FY 01 Work Activities (CRWMS M and O 2001, p. 15), the scope of work includes the following: (1) Review source terms generated by the Waste Package Department (WPD) for various waste forms and waste package types, and compile them for shielding-specific applications. (2) Determine acceptable waste package specific source terms for use in subsurface shielding design, using a reasonable and defensible methodology that is not unduly conservative. This calculation is associated with the engineering and design activity for the waste emplacement and retrieval system, and subsurface facility system. The technical work plan for this calculation is provided in CRWMS M and O 2001. Development and performance of this calculation conforms to the procedure, AP-3.12Q, Calculations

  1. Advanced Reactor PSA Methodologies for System Reliability Analysis and Source Term Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Grabaskas, D.; Brunett, A.; Passerini, S.; Grelle, A.; Bucknor, M.

    2017-06-26

    Beginning in 2015, a project was initiated to update and modernize the probabilistic safety assessment (PSA) of the GE-Hitachi PRISM sodium fast reactor. This project is a collaboration between GE-Hitachi and Argonne National Laboratory (Argonne), and funded in part by the U.S. Department of Energy. Specifically, the role of Argonne is to assess the reliability of passive safety systems, complete a mechanistic source term calculation, and provide component reliability estimates. The assessment of passive system reliability focused on the performance of the Reactor Vessel Auxiliary Cooling System (RVACS) and the inherent reactivity feedback mechanisms of the metal fuel core. The mechanistic source term assessment attempted to provide a sequence specific source term evaluation to quantify offsite consequences. Lastly, the reliability assessment focused on components specific to the sodium fast reactor, including electromagnetic pumps, intermediate heat exchangers, the steam generator, and sodium valves and piping.

  2. Recent advances in acceleration of source iterations for fixed-source slab-geometry S{sub N} calculations based on P{sub N} synthetic initial guess

    Energy Technology Data Exchange (ETDEWEB)

    Guida, Mateus Rodrigues; Alves Filho, Hermes; Barros, Ricardo C., E-mail: mguida@iprj.uerj.br, E-mail: halves@iprj.uerj.br, E-mail: rcbarros@pq.cnpq.br [Universidade do Estado do Rio de Janeiro (UERJ), Nova Friburgo, RJ (Brazil). Instituto Politecnico. Programa de Pos-Graduacao em Modelagem Computacional

    2015-07-01

    The scattering source iterative (SI) scheme is applied traditionally to converge fine-mesh numerical solutions to fixed-source discrete ordinates (S{sub N}) neutron transport problems with linearly anisotropic scattering. The SI scheme is very simple to implement under a computational viewpoint. However, the SI scheme may show very slow convergence rate, mainly for diffusive media (low absorption) with several mean free paths in extent. In this work we describe two acceleration techniques based on improved initial guesses for the SI scheme, wherein we initialize the scattering source distribution within the slab using the P{sub 1} and P{sub 3} approximations. In order to estimate these initial guesses, we use the coarse-mesh solution of the PN equations with special boundary conditions to account for the classical S{sub N} prescribed boundary conditions, including vacuum boundary conditions. To apply this coarse-mesh P{sub N} solution for the accelerated scheme, we first perform within-node spatial reconstruction, and then we determine the fine-mesh average scalar flux and total current for initializing the linearly anisotropic scattering source terms for the SI scheme. We consider a number of numerical experiments to illustrate the efficiency of the offered P{sub N} synthetic acceleration (P{sub N}SA) technique based on initial guess. (author)

  3. Low-level radioactive waste source terms for the 1992 integrated data base

    International Nuclear Information System (INIS)

    Loghry, S.L.; Kibbey, A.H.; Godbee, H.W.; Icenhour, A.S.; DePaoli, S.M.

    1995-01-01

    This technical manual presents updated generic source terms (i.e., unitized amounts and radionuclide compositions) which have been developed for use in the Integrated Data Base (IDB) Program of the U.S. Department of Energy (DOE). These source terms were used in the IDB annual report, Integrated Data Base for 1992: Spent Fuel and Radioactive Waste Inventories, Projections, and Characteristics, DOE/RW-0006, Rev. 8, October 1992. They are useful as a basis for projecting future amounts (volume and radioactivity) of low-level radioactive waste (LLW) shipped for disposal at commercial burial grounds or sent for storage at DOE solid-waste sites. Commercial fuel cycle LLW categories include boiling-water reactor, pressurized-water reactor, fuel fabrication, and uranium hexafluoride (UF 6 ) conversion. Commercial nonfuel cycle LLW includes institutional/industrial (I/I) waste. The LLW from DOE operations is category as uranium/thorium fission product, induced activity, tritium, alpha, and open-quotes otherclose quotes. Fuel cycle commercial LLW source terms are normalized on the basis of net electrical output [MW(e)-year], except for UF 6 conversion, which is normalized on the basis of heavy metal requirement [metric tons of initial heavy metal ]. The nonfuel cycle commercial LLW source term is normalized on the basis of volume (cubic meters) and radioactivity (curies) for each subclass within the I/I category. The DOE LLW is normalized in a manner similar to that for commercial I/I waste. The revised source terms are based on the best available historical data through 1992

  4. Aerosol behavior and light water reactor source terms

    International Nuclear Information System (INIS)

    Abbey, F.; Schikarski, W.O.

    1988-01-01

    The major developments in nuclear aerosol modeling following the accident to pressurized water reactor Unit 2 at Three Mile Island are briefly reviewed and the state of the art summarized. The importance and implications of these developments for severe accident source terms for light water reactors are then discussed in general terms. The treatment is not aimed at identifying specific source term values but is intended rather to illustrate trends, to assess the adequacy of the understanding of major aspects of aerosol behavior for source term prediction, and demonstrate in qualitative terms the effect of various aspects of reactor design. Areas where improved understanding of aerosol behavior might lead to further reductions in current source terms predictions are also considered

  5. Mechanistic facility safety and source term analysis

    International Nuclear Information System (INIS)

    PLYS, M.G.

    1999-01-01

    A PC-based computer program was created for facility safety and source term analysis at Hanford The program has been successfully applied to mechanistic prediction of source terms from chemical reactions in underground storage tanks, hydrogen combustion in double contained receiver tanks, and proccss evaluation including the potential for runaway reactions in spent nuclear fuel processing. Model features include user-defined facility room, flow path geometry, and heat conductors, user-defined non-ideal vapor and aerosol species, pressure- and density-driven gas flows, aerosol transport and deposition, and structure to accommodate facility-specific source terms. Example applications are presented here

  6. Some practical implications of source term reassessment

    International Nuclear Information System (INIS)

    1988-03-01

    This report provides a brief summary of the current knowledge of severe accident source terms and suggests how this knowledge might be applied to a number of specific aspects of reactor safety. In preparing the report, consideration has been restricted to source term issues relating to light water reactors (LWRs). Consideration has also generally been restricted to the consequences of hypothetical severe accidents rather than their probability of occurrence, although it is recognized that, in the practical application of source term research, it is necessary to take account of probability as well as consequences. The specific areas identified were as follows: Exploration of the new insights that are available into the management of severe accidents; Investigating the impact of source term research on emergency planning and response; Assessing the possibilities which exist in present reactor designs for preventing or mitigating the consequences of severe accidents and how these might be used effectively; Exploring the need for backfitting and assessing the implications of source term research for future designs; and Improving the quantification of the radiological consequences of hypothetical severe accidents for probabilistic safety assessments (PSAs) and informing the public about the realistic risks associated with nuclear power plants. 7 refs

  7. Revised accident source terms for light-water reactors

    Energy Technology Data Exchange (ETDEWEB)

    Soffer, L. [Nuclear Regulatory Commission, Washington, DC (United States)

    1995-02-01

    This paper presents revised accident source terms for light-water reactors incorporating the severe accident research insights gained in this area over the last 15 years. Current LWR reactor accident source terms used for licensing date from 1962 and are contained in Regulatory Guides 1.3 and 1.4. These specify that 100% of the core inventory of noble gases and 25% of the iodine fission products are assumed to be instantaneously available for release from the containment. The chemical form of the iodine fission products is also assumed to be predominantly elemental iodine. These assumptions have strongly affected present nuclear air cleaning requirements by emphasizing rapid actuation of spray systems and filtration systems optimized to retain elemental iodine. A proposed revision of reactor accident source terms and some im implications for nuclear air cleaning requirements was presented at the 22nd DOE/NRC Nuclear Air Cleaning Conference. A draft report was issued by the NRC for comment in July 1992. Extensive comments were received, with the most significant comments involving (a) release fractions for both volatile and non-volatile species in the early in-vessel release phase, (b) gap release fractions of the noble gases, iodine and cesium, and (c) the timing and duration for the release phases. The final source term report is expected to be issued in late 1994. Although the revised source terms are intended primarily for future plants, current nuclear power plants may request use of revised accident source term insights as well in licensing. This paper emphasizes additional information obtained since the 22nd Conference, including studies on fission product removal mechanisms, results obtained from improved severe accident code calculations and resolution of major comments, and their impact upon the revised accident source terms. Revised accident source terms for both BWRS and PWRS are presented.

  8. Revised accident source terms and control room habitability

    International Nuclear Information System (INIS)

    Lahti, G.P.; Hubner, R.S.; Johnson, W.J.; Schwartz, B.C.

    1993-01-01

    In April 1992, the NRC staff presented to the Commissioners the draft NUREG open-quotes Revised Accident Source Terms for Light-Water Nuclear Power Plants.close quotes This document is the culmination of more than ten years of NRC-sponsored research and represents the first change in the NRC's position on source terms since TID-14844 was issued in 1962. The purpose of this paper is to investigate the impact of the revised source terms on the current approach to analyzing control room habitability as required by 10 CFR 50. Sample calculations are presented that identify aspects of the model requiring clarification before the implementation of the revised source terms. 6 refs., 4 tabs

  9. Some problems in the categorization of source terms

    International Nuclear Information System (INIS)

    Abbey, F.; Dunbar, I.H.; Hayns, M.R.; Nixon, W.

    1985-01-01

    In recent years techniques for calculating source terms have been considerably improved. It would be unfortunate if the new information were to be blurred by the use of old schemes for the categorization of source terms. In the past categorization schemes have been devised without the question of the general principles of categorization and the available options being addressed explicitly. In this paper these principles are set out, providing a framework within which categorization schemes used in past probabilistic risk assessments and possible future improvements are discussed. In particular the use of input from scoping consequence calculations in deciding how to group source terms, and the question of how modelling uncertainties may be expressed as uncertainties in a final category source terms are considered

  10. Philanthropy as a source of funding for nursing initiatives.

    Science.gov (United States)

    Kleinpell, Ruth M; Start, Rachel; McIntosh, Erik; Worobec, Sophia; Llewellyn, Jane

    2014-01-01

    Nurse leaders are challenged with ensuring that research and evidence-based practices are being integrated into clinical care. Initiatives such as the Magnet Recognition Program have helped reinforce the importance of advancing nursing practices to integrate best practices, conduct quality improvement initiatives, improve performance metrics, and involve bedside nurses in conducting research and evidence-based practice projects. While seeking research funding is an option for some initiatives, other strategies such as seeking funding from grateful patients or from philanthropic resources are becoming important options for nurse leaders to pursue, as the availability of funding from traditional sources such as professional organizations or federal funding becomes more limited. In addition, more institutions are seeking and applying for funding, increasing the pool of candidates who are vying for existing funding. Seeking alternative sources of funding, such as through philanthropy, becomes a viable option. This article reviews important considerations in seeking funding from philanthropic sources for nursing initiatives. Examples from a multiyear project that focused on promoting a healthy work environment and improving nursing morale are used to highlight strategies that were used to solicit, obtain, and secure extension funding from private foundation funding to support the initiative.

  11. The Chernobyl reactor accident source term: Development of a consensus view

    International Nuclear Information System (INIS)

    Guntay, S.; Powers, D.A.; Devell, L.

    1997-01-01

    In August 1986, scientists from the former Soviet Union provided the nuclear safety community with an impressively detailed account of what was then known about the Chernobyl accident. This included assessments of the magnitudes, rates, and compositions of radionuclide releases during the ten days following initiation of the accident. A summary report based on the Soviet report, the oral presentations, and the discussions with scientists from various countries was issued by the International Atomic Energy Agency shortly thereafter. Ten years have elapsed since the reactor accident at Chernobyl. A great deal more data is now available concerning the events, phenomena, and processes that took place. The purpose of this document is to examine what is known about the radioactive materials released during the accident. The accident was peculiar in the sense that radioactive materials were released, at least initially, in an exceptionally energetic plume and were transported far from the reactor site. Release of radioactivity from the plant continued for about ten days. A number of more recent publications and results from scientists in Russia and elsewhere have significantly improved our understanding of the Chernobyl source term. Because of the special features of the reactor design and the pecularities of the Chernobyl accident, the source term for the Chernobyl accident is of limited applicability of the safety analysis of other types of reactors

  12. Probabilistic source term predictions for use with decision support systems

    International Nuclear Information System (INIS)

    Grindon, E.; Kinniburgh, C.G.

    2003-01-01

    Full text: Decision Support Systems for use in off-site emergency management, following an incident at a Nuclear Power Plant (NPP) within Europe, are becoming accepted as a useful and appropriate tool to aid decision makers. An area which is not so well developed is the 'upstream' prediction of the source term released into the environment. Rapid prediction of this source term is crucial to the appropriate early management of a nuclear emergency. The initial source term prediction would today be typically based on simple tabulations taking little, or no, account of plant status. It is the interface between the inward looking plant control room team and the outward looking off-site emergency management team that needs to be addressed. This is not an easy proposition as these two distinct disciplines have little common basis from which to communicate their immediate findings and concerns. Within the Euratom Fifth Framework Programme (FP5), complementary approaches are being developed to the pre-release stage; each based on software tools to help bridge this gap. Traditionally source terms (or releases into the environment) provided for use with Decision Support Systems are estimated on a deterministic basis. These approaches use a single, deterministic assumption about plant status. The associated source term represents the 'best estimate' based an available information. No information is provided an the potential for uncertainty in the source term estimate. Using probabilistic methods the outcome is typically a number of possible plant states each with an associated source term and probability. These represent both the best estimate and the spread of the likely source term. However, this is a novel approach and the usefulness of such source term prediction tools is yet to be tested on a wide scale. The benefits of probabilistic source term estimation are presented here; using, as an example, the SPRINT tool developed within the FP5 STERPS project. System for the

  13. Evaluation of short- and long-term fission product sources at the Fukushima Daiichi NPP

    International Nuclear Information System (INIS)

    Uchida, Shunsuke; Naitoh, Masanori; Suzuki, Hiroaki; Okada, Hidetoshi; Pellegrini, Marco; Achilli, Andrea; Hanamoto, Yukio; Sasaki, Hiroaki

    2014-01-01

    Research on fission product (FP) behaviors used to be one of the most important subjects in water chemistry but it is not done nowadays as a consequence of the increased integrity of nuclear fuels and the minimization of FP release into the environment. Evaluation of FP release into the environment is still one of the key issues for severe accident analysis, though. Although there have been a long quiet period in nuclear safety research, how to detect initiation of severe accidents, how to prevent them and how to mitigate them are still important subjects for nuclear engineering, and how to control the severe accidents after their occurrence, especially how to control FP release into the environment, has seldom been discussed in the water chemistry group recently. The paper is intended to address the issue of fewer activities for FP studies. FP sources are divided into two categories, short- and long-term FP sources. Short-term FP source can be evaluated based on the measured data obtained from monitoring posts (MPs), which give us clear evidence on the importance of radioactive iodine and cesium releases into the environment. It used to be considered that during primary containment vessel (PCV) venting, release of each element, e.g., iodine and cesium, was determined by the suppression pool scrubbing efficiency and most of the cesium would likely be removed in the pool due to its large scrubbing efficiency. But as a result of analyzing the MP data at early stage of the Fukushima Daiichi nuclear power plant (NPP) accident, it was confirmed that the releases of both elements were in proportion to their inventories in the reactors and their scrubbing efficiencies were almost the same. The scrubbing efficiency which increased with the pool water temperature became almost the same for iodine and cesium around the pool water boiling temperature. As a result of the mass balance analysis for FPs in the contaminated water accumulated in the Fukushima Daiichi plant site, it

  14. Chernobyl source term estimation

    International Nuclear Information System (INIS)

    Gudiksen, P.H.; Harvey, T.F.; Lange, R.

    1990-09-01

    The Chernobyl source term available for long-range transport was estimated by integration of radiological measurements with atmospheric dispersion modeling and by reactor core radionuclide inventory estimation in conjunction with WASH-1400 release fractions associated with specific chemical groups. The model simulations revealed that the radioactive cloud became segmented during the first day, with the lower section heading toward Scandinavia and the upper part heading in a southeasterly direction with subsequent transport across Asia to Japan, the North Pacific, and the west coast of North America. By optimizing the agreement between the observed cloud arrival times and duration of peak concentrations measured over Europe, Japan, Kuwait, and the US with the model predicted concentrations, it was possible to derive source term estimates for those radionuclides measured in airborne radioactivity. This was extended to radionuclides that were largely unmeasured in the environment by performing a reactor core radionuclide inventory analysis to obtain release fractions for the various chemical transport groups. These analyses indicated that essentially all of the noble gases, 60% of the radioiodines, 40% of the radiocesium, 10% of the tellurium and about 1% or less of the more refractory elements were released. These estimates are in excellent agreement with those obtained on the basis of worldwide deposition measurements. The Chernobyl source term was several orders of magnitude greater than those associated with the Windscale and TMI reactor accidents. However, the 137 Cs from the Chernobyl event is about 6% of that released by the US and USSR atmospheric nuclear weapon tests, while the 131 I and 90 Sr released by the Chernobyl accident was only about 0.1% of that released by the weapon tests. 13 refs., 2 figs., 7 tabs

  15. Source term and radiological consequences of the Chernobyl accident

    International Nuclear Information System (INIS)

    Mourad, R.

    1987-09-01

    This report presents the results of a study of the source term and radiological consequences of the Chernobyl accident. The results two parts. The first part was performed during the first 2 months following the accident and dealt with the evaluation of the source term and an estimate of individual doses in the European countries outside the Soviet Union. The second part was performed after August 25-29, 1986 when the Soviets presented in a IAEA Conference in Vienna detailed information about the accident, including source term and radiological consequences in the Soviet Union. The second part of the study reconfirms the source term evaluated in the first part and in addition deals with the radiological consequences in the Soviet Union. Source term and individual doses are calculated from measured post-accident data, reported by the Soviet Union and European countries, microcomputer program PEAR (Public Exposure from Accident Releases). 22 refs

  16. Phase 1 immobilized low-activity waste operational source term

    International Nuclear Information System (INIS)

    Burbank, D.A.

    1998-01-01

    This report presents an engineering analysis of the Phase 1 privatization feeds to establish an operational source term for storage and disposal of immobilized low-activity waste packages at the Hanford Site. The source term information is needed to establish a preliminary estimate of the numbers of remote-handled and contact-handled waste packages. A discussion of the uncertainties and their impact on the source term and waste package distribution is also presented. It should be noted that this study is concerned with operational impacts only. Source terms used for accident scenarios would differ due to alpha and beta radiation which were not significant in this study

  17. IKEA: Global sourcing and sustainable leather initiatives

    OpenAIRE

    Jiang, Yan; Jia, Fu; Gong, Yu

    2018-01-01

    Aims: the aim of this teaching case is to illustrate the Sustainable Global Sourcing (SGS) practices of IKEA influenced by its Global Sourcing (GS) strategy and structure aspects through a case study of the sustainable leather initiative.Scope: this study is developed though 20 face-to-face interviews with IKEA managers in both Sweden and China, covering all the major SGS-related departments i.e. purchasing,sustainability, IWAY, and competence center (sustainable project team).Contribution: w...

  18. Source term analyses under severe accidents for KNGR

    Energy Technology Data Exchange (ETDEWEB)

    Song, Yong Mann; Park, Soo Yong

    2001-03-01

    In this study, in-containment source term for LOFW (Loss of Feed Water), which has appeared the most frequent core melt accident, is calculated and compared with NUREG-1465 source term. This study provides not only new source term data using MELCOR1.8.4 and its state-of-the-art models but also evaluating basis of KNGR design and its mitigation capability under severe accidents. As the selected accident is identical with LOFW-S17, which has been analyzed using MAAP by KEPCO with only difference of 2 SITs, mutual comparison of the results is especially expected.

  19. Long-term program up to fiscal 1993 of electric power source development

    International Nuclear Information System (INIS)

    Kawakami, Shin-ichi

    1984-01-01

    The long-term, ten years, program up to fiscal 1993 of electric power source development, determined by the Government aims at stable power supply and the expansion of utilization of petroleum-substitute energy. The annual growth in the gross national product (GNP) during the ten years was taken as about 4 %. So, the total electric power demand in fiscal 1993 is scheduled to be 731,000 million kwh, about 34 % up from 547,000 million kwh in fiscal 1983. The structure of electric power sources at the end of fiscal 1993 will be hydraulic 19.7 %, thermal 58.3 %, and nuclear 21.9 %. The development of electric power sources to be initiated in fiscal 1984 is hydraulic 500 MW, thermal 2,000 MW, and nuclear 6,000 MW. (Mori, K.)

  20. A simplified approach to evaluating severe accident source term for PWR

    International Nuclear Information System (INIS)

    Huang, Gaofeng; Tong, Lili; Cao, Xuewu

    2014-01-01

    Highlights: • Traditional source term evaluation approaches have been studied. • A simplified approach of source term evaluation for 600 MW PWR is studied. • Five release categories are established. - Abstract: For early design of NPPs, no specific severe accident source term evaluation was considered. Some general source terms have been used for some NPPs. In order to implement a best estimate, a special source term evaluation should be implemented for an NPP. Traditional source term evaluation approaches (mechanism approach and parametric approach) have some difficulties associated with their implementation. The traditional approaches are not consistent with cost-benefit assessment. A simplified approach for evaluating severe accident source term for PWR is studied. For the simplified approach, a simplified containment event tree is established. According to representative cases selection, weighted coefficient evaluation, computation of representative source term cases and weighted computation, five containment release categories are established, including containment bypass, containment isolation failure, containment early failure, containment late failure and intact containment

  1. Radiological and chemical source terms for Solid Waste Operations Complex

    International Nuclear Information System (INIS)

    Boothe, G.F.

    1994-01-01

    The purpose of this document is to describe the radiological and chemical source terms for the major projects of the Solid Waste Operations Complex (SWOC), including Project W-112, Project W-133 and Project W-100 (WRAP 2A). For purposes of this document, the term ''source term'' means the design basis inventory. All of the SWOC source terms involve the estimation of the radiological and chemical contents of various waste packages from different waste streams, and the inventories of these packages within facilities or within a scope of operations. The composition of some of the waste is not known precisely; consequently, conservative assumptions were made to ensure that the source term represents a bounding case (i.e., it is expected that the source term would not be exceeded). As better information is obtained on the radiological and chemical contents of waste packages and more accurate facility specific models are developed, this document should be revised as appropriate. Radiological source terms are needed to perform shielding and external dose calculations, to estimate routine airborne releases, to perform release calculations and dose estimates for safety documentation, to calculate the maximum possible fire loss and specific source terms for individual fire areas, etc. Chemical source terms (i.e., inventories of combustible, flammable, explosive or hazardous chemicals) are used to determine combustible loading, fire protection requirements, personnel exposures to hazardous chemicals from routine and accident conditions, and a wide variety of other safety and environmental requirements

  2. Open Source Initiative Powers Real-Time Data Streams

    Science.gov (United States)

    2014-01-01

    Under an SBIR contract with Dryden Flight Research Center, Creare Inc. developed a data collection tool called the Ring Buffered Network Bus. The technology has now been released under an open source license and is hosted by the Open Source DataTurbine Initiative. DataTurbine allows anyone to stream live data from sensors, labs, cameras, ocean buoys, cell phones, and more.

  3. Effect of source term composition on offsite doses

    International Nuclear Information System (INIS)

    Karahalios, P.; Gardner, R.

    1985-01-01

    The development of new realistic accident source terms has identified the need to establish a basis for comparing the impact of such source terms. This paper attempts to develop a generalized basis of comparison by investigating contributions to offsite acute whole body doses from each group of radionuclides being released to the atmosphere, using CRAC2. The paper also investigates the effect of important parameters such as regional meteorology, sheltering, and duration of release. Finally, the paper focuses on significant changes in the relative importance of individual radionuclide groups in PWR2, SST1, and a revision of the Stone and Webster proposed interim source term

  4. Design parameters and source terms: Volume 3, Source terms: Revision 0

    International Nuclear Information System (INIS)

    1987-09-01

    The Design Parameters and Source Terms Document was prepared in accordance with DOE request and to provide data for the environmental impact study to be performed in the future for the Deaf Smith County, Texas site for a nuclear waste repository in salt. This document updates a previous unpublished report to the level of the Site Characterization Plan /endash/ Conceptual Design Report, SCP-CDR. The previous unpublished SCC Study identifies the data needs for the Environmental Assessment effort for seven possible salt repository sites

  5. The impact of source initialization on performance of the FMBMC-ICEU algorithm

    International Nuclear Information System (INIS)

    Wenner, Michael T.; Haghighat, Alireza

    2011-01-01

    Recent work in the completely fission matrix based Monte Carlo (FMBMC) eigenvalue methodology showed that the fission matrix coefficients are independent of the source eigenvector in the limit of small mesh sizes. As a result, fission matrix element autocorrelation should be insignificant. We have developed a modified fission matrix based Monte Carlo methodology for achieving unbiased solutions even for high Dominance Ratio (DR) problems. This methodology utilizes an initial source from a deterministic calculation using the PENTRAN 3-D Parallel SN code, autocorrelation and normality tests, and a Monte Carlo Iterated Confidence Interval (ICI) formulation for estimation of uncertainties in the fundamental eigenvalue and eigenfunction. This methodology is referred to as Fission Matrix Based Monte Carlo Initial-source Controlled Elements with Uncertainties (FMBMC-ICEU). In this paper, we will investigate the impact of different starting sources (PENTRAN initialized with a flat source and a boundary source) on the final results of a test problem with high source correlation. It is shown that although the fission matrix element correlation is significantly reduced, a good initial guess is still important within the framework of the FMBMC-ICEU methodology since the FMBMC-ICEU methodology still utilizes a standard source iteration scheme. (author)

  6. Bayesian source term determination with unknown covariance of measurements

    Science.gov (United States)

    Belal, Alkomiet; Tichý, Ondřej; Šmídl, Václav

    2017-04-01

    Determination of a source term of release of a hazardous material into the atmosphere is a very important task for emergency response. We are concerned with the problem of estimation of the source term in the conventional linear inverse problem, y = Mx, where the relationship between the vector of observations y is described using the source-receptor-sensitivity (SRS) matrix M and the unknown source term x. Since the system is typically ill-conditioned, the problem is recast as an optimization problem minR,B(y - Mx)TR-1(y - Mx) + xTB-1x. The first term minimizes the error of the measurements with covariance matrix R, and the second term is a regularization of the source term. There are different types of regularization arising for different choices of matrices R and B, for example, Tikhonov regularization assumes covariance matrix B as the identity matrix multiplied by scalar parameter. In this contribution, we adopt a Bayesian approach to make inference on the unknown source term x as well as unknown R and B. We assume prior on x to be a Gaussian with zero mean and unknown diagonal covariance matrix B. The covariance matrix of the likelihood R is also unknown. We consider two potential choices of the structure of the matrix R. First is the diagonal matrix and the second is a locally correlated structure using information on topology of the measuring network. Since the inference of the model is intractable, iterative variational Bayes algorithm is used for simultaneous estimation of all model parameters. The practical usefulness of our contribution is demonstrated on an application of the resulting algorithm to real data from the European Tracer Experiment (ETEX). This research is supported by EEA/Norwegian Financial Mechanism under project MSMT-28477/2014 Source-Term Determination of Radionuclide Releases by Inverse Atmospheric Dispersion Modelling (STRADI).

  7. A comparison of world-wide uses of severe reactor accident source terms

    International Nuclear Information System (INIS)

    Ang, M.L.; Frid, W.; Kersting, E.J.; Friederichs, H.G.; Lee, R.Y.; Meyer-Heine, A.; Powers, D.A.; Soda, K.; Sweet, D.

    1994-09-01

    The definitions of source terms to reactor containments and source terms to the environment are discussed. A comparison is made between the TID-14844 example source term and the alternative source term described in NUREG-1465. Comparisons of these source terms to the containments and those used in France, Germany, Japan, Sweden, and the United Kingdom are made. Source terms to the environment calculated in NUREG-1500 and WASH-1400 are discussed. Again, these source terms are compared to those now being used in France, Germany, Japan, Sweden, and the United Kingdom. It is concluded that source terms to the containment suggested in NUREG-1465 are not greatly more conservative than those used in other countries. Technical bases for the source terms are similar. The regulatory use of the current understanding of radionuclide behavior varies among countries

  8. Source term evaluation model for high-level radioactive waste repository with decay chain build-up.

    Science.gov (United States)

    Chopra, Manish; Sunny, Faby; Oza, R B

    2016-09-18

    A source term model based on two-component leach flux concept is developed for a high-level radioactive waste repository. The long-lived radionuclides associated with high-level waste may give rise to the build-up of activity because of radioactive decay chains. The ingrowths of progeny are incorporated in the model using Bateman decay chain build-up equations. The model is applied to different radionuclides present in the high-level radioactive waste, which form a part of decay chains (4n to 4n + 3 series), and the activity of the parent and daughter radionuclides leaching out of the waste matrix is estimated. Two cases are considered: one when only parent is present initially in the waste and another where daughters are also initially present in the waste matrix. The incorporation of in situ production of daughter radionuclides in the source is important to carry out realistic estimates. It is shown that the inclusion of decay chain build-up is essential to avoid underestimation of the radiological impact assessment of the repository. The model can be a useful tool for evaluating the source term of the radionuclide transport models used for the radiological impact assessment of high-level radioactive waste repositories.

  9. Quantification of severe accident source terms of a Westinghouse 3-loop plant

    International Nuclear Information System (INIS)

    Lee Min; Ko, Y.-C.

    2008-01-01

    Integrated severe accident analysis codes are used to quantify the source terms of the representative sequences identified in PSA study. The characteristics of these source terms depend on the detail design of the plant and the accident scenario. A historical perspective of radioactive source term is provided. The grouping of radionuclides in different source terms or source term quantification tools based on TID-14844, NUREG-1465, and WASH-1400 is compared. The radionuclides release phenomena and models adopted in the integrated severe accident analysis codes of STCP and MAAP4 are described. In the present study, the severe accident source terms for risk quantification of Maanshan Nuclear Power Plant of Taiwan Power Company are quantified using MAAP 4.0.4 code. A methodology is developed to quantify the source terms of each source term category (STC) identified in the Level II PSA analysis of the plant. The characteristics of source terms obtained are compared with other source terms. The plant analyzed employs a Westinghouse designed 3-loop pressurized water reactor (PWR) with large dry containment

  10. The Chernobyl reactor accident source term: development of a consensus view

    International Nuclear Information System (INIS)

    Devell, L.; Guntay, S.; Powers, D.A.

    1995-11-01

    Ten years after the reactor accident at Chernobyl, a great deal more data is available concerning the events, phenomena, and processes that took place. The purpose of this document is to examine what is known about the radioactive materials released during the accident, a task that is substantially more difficult than it might first appear to be. The Chernobyl station, like other nuclear power plants, was not instrumented to characterize a disastrous accident. The accident was peculiar in the sense that radioactive materials were released, at least initially, in an exceptionally energetic plume and were transported far from the reactor site. Release of radioactivity from the plant continued for several days. Characterization of the contamination caused by the releases of radioactivity has had a much lower priority than remediation of the contamination. Consequently, an assessment of the Chernobyl accident source term must rely to a significant extent on inferential evidence. The assessment presented here begins with an examination of the core inventories of radioactive materials. In subsequent sections of the report, the magnitude and timing of the releases of radioactivity are described. Then, the composition, chemical forms, and physical forms of the releases are discussed. A number of more recent publications and results from scientists in Russia and elsewhere have significantly improved the understanding of the Chernobyl source term. Because of the special features of the reactor design and the peculiarities of the Chernobyl accident, the source term for the Chernobyl accident is of limited applicability to the safety analysis of other types of reactors

  11. Estimation of Source Term Behaviors in SBO Sequence in a Typical 1000MWth PWR and Comparison with Other Source Term Results

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Tae Woon; Han, Seok Jung; Ahn, Kwang Il; Fynan, Douglas; Jung, Yong Hoon [KAERI, Daejeon (Korea, Republic of)

    2016-05-15

    Since the Three Mile Island (TMI) (1979), Chernobyl (1986), Fukushima Daiichi (2011) accidents, the assessment of radiological source term effects on the environment has been a key concern of nuclear safety. In the Fukushima Daiichi accident, the long-term SBO (station blackout) accident occurs. Using the worst case assumptions like in Fukushima accident on the accident sequences and on the availability of safety systems, the thermal hydraulic behaviors, core relocation and environmental source terms behaviors are estimated for long-term SBO accident for OPR-1000 reactor. MELCOR code version 1.8.6 is used in this analysis. Source term results estimated in this study is compared with other previous studies and estimated results in Fukushima accidents in UNSCEAR-2013 report. This study estimated that 11 % of iodine can be released to environment and 2% of cesium can be released to environment. UNSCEAR-2013 report estimated that 2 - 8 % of iodine have been released to environment and 1 - 3 % of cesium have been released to the environment. They have similar results in the aspect of release fractions of iodine and cesium to environment.

  12. The United States initiative for international radioactive source management (ISRM)

    International Nuclear Information System (INIS)

    Naraine, N.; Karhnak, J.

    1999-01-01

    The United States takes seriously the potential problems from uncontrolled radioactive sources. To address these problems, the United States Department of State is leading the development of an initiative for International Radioactive Source Management (ISRM). The Department of State, through a number of Federal and state agencies, regulatory bodies and private industry, will endeavor to provide coordinated support to the international community, particularly through IAEA, to assist in the development and implementation of risk-based clearance levels to support import/export of radioactive contaminated metals and the tracking, management, identification, remediation, and disposition of 'lost sources' entering nation states and targeted industries. The United States believes that the international control of radioactive sources is critical in avoiding wide-spread contamination of the world metal supply. Thus the initiative has four objectives: (1) Protect sources from becoming lost (Tracking management); (2) Identify primary locations where sources have been lost (Stop future losses); (3) Locate lost sources (monitor and retrieve); and (4) Educate and train (deploy knowledge and technology). A number of efforts already underway in the United States support the overall initiative. The EPA has provided a grant to the Conference of Radiation Program Control Directors (CRCPD) to develop a nation-wide program for the disposition of orphaned radioactive sources. This program now has internet visibility and a toll-free telephone number to call for assistance in the disposal of sources. The Nuclear Regulatory Commission (NRC), the Department of Energy (DOE), and other government agencies as well as private companies are assisting CRCPD in this program. The NRC has begun a program to improve control of radioactive sources in the United States, and also intends to promulgate a regulation defining conditions for the release of materials from licensed facilities. The DOE is

  13. Selection of models to calculate the LLW source term

    International Nuclear Information System (INIS)

    Sullivan, T.M.

    1991-10-01

    Performance assessment of a LLW disposal facility begins with an estimation of the rate at which radionuclides migrate out of the facility (i.e., the source term). The focus of this work is to develop a methodology for calculating the source term. In general, the source term is influenced by the radionuclide inventory, the wasteforms and containers used to dispose of the inventory, and the physical processes that lead to release from the facility (fluid flow, container degradation, wasteform leaching, and radionuclide transport). In turn, many of these physical processes are influenced by the design of the disposal facility (e.g., infiltration of water). The complexity of the problem and the absence of appropriate data prevent development of an entirely mechanistic representation of radionuclide release from a disposal facility. Typically, a number of assumptions, based on knowledge of the disposal system, are used to simplify the problem. This document provides a brief overview of disposal practices and reviews existing source term models as background for selecting appropriate models for estimating the source term. The selection rationale and the mathematical details of the models are presented. Finally, guidance is presented for combining the inventory data with appropriate mechanisms describing release from the disposal facility. 44 refs., 6 figs., 1 tab

  14. Review of SFR In-Vessel Radiological Source Term Studies

    International Nuclear Information System (INIS)

    Suk, Soo Dong; Lee, Yong Bum

    2008-10-01

    An effort has been made in this study to search for and review the literatures in public domain on the studies of the phenomena related to the release of radionuclides and aerosols to the reactor containment of the sodium fast reactor (SFR) plants (i.e., in-vessel source term), made in Japan and Europe including France, Germany and UK over the last few decades. Review work is focused on the experimental programs to investigate the phenomena related to determining the source terms, with a brief review on supporting analytical models and computer programs. In this report, the research programs conducted to investigate the CDA (core disruptive accident) bubble behavior in the sodium pool for determining 'primary' or 'instantaneous' source term are first introduced. The studies performed to determine 'delayed source term' are then described, including the various stages of phenomena and processes: fission product (FP) release from fuel , evaporation release from the surface of the pool, iodine mass transfer from fission gas bubble, FP deposition , and aerosol release from core-concrete interaction. The research programs to investigate the release and transport of FPs and aerosols in the reactor containment (i.e., in-containment source term) are not described in this report

  15. Utility view of the source term and air cleaning

    International Nuclear Information System (INIS)

    Littlefield, P.S.

    1985-01-01

    The utility view of the source term and air cleaning is discussed. The source term is made up of: (1) noble gases, which there has been a tendency to ignore in the past because it was thought there was nothing that could be done with them anyway, (2) the halogens, which have been dealt with in Air Cleaning Conferences in the past in terms of charcoal and other systems for removing them, and (3) the solid components of the source term which particulate filters are designed to handle. Air cleaning systems consist of filters, adsorbers, containment sprays, suppression pools in boiling water reactors and ice beds in ice condenser-equipped plants. The feasibility and cost of air cleaning systems are discussed

  16. Lysimeter data as input to performance assessment source term codes

    International Nuclear Information System (INIS)

    McConnell, J.W. Jr.; Rogers, R.D.; Sullivan, T.

    1992-01-01

    The Field Lysimeter Investigation: Low-Level Waste Data Base Development Program is obtaining information on the performance of radioactive waste in a disposal environment. Waste forms fabricated using ion-exchange resins from EPICOR-II c prefilters employed in the cleanup of the Three Mile Island (TMI) Nuclear Power Station are being tested to develop a low-level waste data base and to obtain information on survivability of waste forms in a disposal environment. In this paper, radionuclide releases from waste forms in the first seven years of sampling are presented and discussed. Application of lysimeter data to be used in performance assessment source term models is presented. Initial results from use of data in two models are discussed

  17. Low-level radioactive waste performance assessments: Source term modeling

    International Nuclear Information System (INIS)

    Icenhour, A.S.; Godbee, H.W.; Miller, L.F.

    1995-01-01

    Low-level radioactive wastes (LLW) generated by government and commercial operations need to be isolated from the environment for at least 300 to 500 yr. Most existing sites for the storage or disposal of LLW employ the shallow-land burial approach. However, the U.S. Department of Energy currently emphasizes the use of engineered systems (e.g., packaging, concrete and metal barriers, and water collection systems). Future commercial LLW disposal sites may include such systems to mitigate radionuclide transport through the biosphere. Performance assessments must be conducted for LUW disposal facilities. These studies include comprehensive evaluations of radionuclide migration from the waste package, through the vadose zone, and within the water table. Atmospheric transport mechanisms are also studied. Figure I illustrates the performance assessment process. Estimates of the release of radionuclides from the waste packages (i.e., source terms) are used for subsequent hydrogeologic calculations required by a performance assessment. Computer models are typically used to describe the complex interactions of water with LLW and to determine the transport of radionuclides. Several commonly used computer programs for evaluating source terms include GWSCREEN, BLT (Breach-Leach-Transport), DUST (Disposal Unit Source Term), BARRIER (Ref. 5), as well as SOURCE1 and SOURCE2 (which are used in this study). The SOURCE1 and SOURCE2 codes were prepared by Rogers and Associates Engineering Corporation for the Oak Ridge National Laboratory (ORNL). SOURCE1 is designed for tumulus-type facilities, and SOURCE2 is tailored for silo, well-in-silo, and trench-type disposal facilities. This paper focuses on the source term for ORNL disposal facilities, and it describes improved computational methods for determining radionuclide transport from waste packages

  18. Literature study of source term research for PWRs

    Energy Technology Data Exchange (ETDEWEB)

    Sponton, L.L.; NiIsson, Lars

    2001-04-01

    A literature survey has been carried out in support of ongoing source term calculations with the MELCOR code of some severe accident scenarios for the Swedish Ringhals 2 pressurised water reactor (PWR). The research in the field of severe accidents in power reactors and the source term for subsequent release of radioisotopes was intensified after the Harrisburg accident and has produced a large amount of reports and papers. This survey was therefore limited to research concerning PWR type of reactors and with emphasis on papers related to MELCOR code development. A background is given, relating to some historic documents, and then more recent research after 1990 is reviewed. Of special interest is the ongoing PMbus-programme which is creating new and important results of benefit to the code development and validation of, among others, the MELCOR code. It is concluded that source term calculations involve simulation of many interacting complex physical phenomena, which result in large uncertainties The research has, however, over the years led to considerable improvements Thus has the uncertainty in source term predictions been reduced one to two orders of magnitude from the simpler codes in the early 1980-s to the more realistic codes of today, like MELCOR.

  19. Literature study of source term research for PWRs

    International Nuclear Information System (INIS)

    Sponton, L.L.; NiIsson, Lars

    2001-04-01

    A literature survey has been carried out in support of ongoing source term calculations with the MELCOR code of some severe accident scenarios for the Swedish Ringhals 2 pressurised water reactor (PWR). The research in the field of severe accidents in power reactors and the source term for subsequent release of radioisotopes was intensified after the Harrisburg accident and has produced a large amount of reports and papers. This survey was therefore limited to research concerning PWR type of reactors and with emphasis on papers related to MELCOR code development. A background is given, relating to some historic documents, and then more recent research after 1990 is reviewed. Of special interest is the ongoing PMbus-programme which is creating new and important results of benefit to the code development and validation of, among others, the MELCOR code. It is concluded that source term calculations involve simulation of many interacting complex physical phenomena, which result in large uncertainties The research has, however, over the years led to considerable improvements Thus has the uncertainty in source term predictions been reduced one to two orders of magnitude from the simpler codes in the early 1980-s to the more realistic codes of today, like MELCOR

  20. Regulatory impact of nuclear reactor accident source term assumptions. Technical report

    International Nuclear Information System (INIS)

    Pasedag, W.F.; Blond, R.M.; Jankowski, M.W.

    1981-06-01

    This report addresses the reactor accident source term implications on accident evaluations, regulations and regulatory requirements, engineered safety features, emergency planning, probabilistic risk assessment, and licensing practice. Assessment of the impact of source term modifications and evaluation of the effects in Design Basis Accident analyses, assuming a change of the chemical form of iodine from elemental to cesium iodide, has been provided. Engineered safety features used in current LWR designs are found to be effective for all postulated combinations of iodine source terms under DBA conditions. In terms of potential accident consequences, it is not expected that the difference in chemical form between elemental iodine and cesium iodide would be significant. In order to account for the current information on source terms, a spectrum of accident scenerios is discussed to realistically estimate the source terms resulting from a range of potential accident conditions

  1. 7-GeV Advanced Photon Source Instrumentation Initiative conceptual design report

    International Nuclear Information System (INIS)

    1992-12-01

    In this APS Instrumentation Initiative, 2.5-m-long and 5-m-long insertion-device x-ray sources will be built on 9 straight sections of the APS storage ring, and an additional 9 bending-magnet sources will also be put in use. The front ends for these 18 x-ray sources will be built to contain and safeguard access to these bright x-ray beams. In addition, funds will be provided to build state-of-the-art insertion-device beamlines to meet scientific and technological research demands well into the next century. This new initiative will also include four user laboratory modules and a special laboratory designed to meet the x-ray imaging research needs of the users. The Conceptual Design Report (CDR) for the APS Instrumentation Initiative describes the scope of all the above technical and conventional construction and provides a detailed cost and schedule for these activities. According to these plans, this new initiative begins in FY 1994 and ends in FY 1998. The document also describes the preconstruction R ampersand D plans for the Instrumentation Initiative activities and provides the cost estimates for the required R ampersand D

  2. Hazardous constituent source term. Revision 2

    International Nuclear Information System (INIS)

    1994-01-01

    The Department of Energy (DOE) has several facilities that either generate and/or store transuranic (TRU)-waste from weapons program research and production. Much of this waste also contains hazardous waste constituents as regulated under Subtitle C of the Resource Conservation and Recovery Act (RCRA). Toxicity characteristic metals in the waste principally include lead, occurring in leaded rubber gloves and shielding. Other RCRA metals may occur as contaminants in pyrochemical salt, soil, debris, and sludge and solidified liquids, as well as in equipment resulting from decontamination and decommissioning activities. Volatile organic compounds (VOCS) contaminate many waste forms as a residue adsorbed on surfaces or occur in sludge and solidified liquids. Due to the presence of these hazardous constituents, applicable disposal regulations include land disposal restrictions established by Hazardous and Solid Waste Amendments (HSWA). The DOE plans to dispose of TRU-mixed waste from the weapons program in the Waste Isolation Pilot Plant (WIPP) by demonstrating no-migration of hazardous constituents. This paper documents the current technical basis for methodologies proposed to develop a post-closure RCRA hazardous constituent source term. For the purposes of demonstrating no-migration, the hazardous constituent source term is defined as the quantities of hazardous constituents that are available for transport after repository closure. Development of the source term is only one of several activities that will be involved in the no-migration demonstration. The demonstration will also include uncertainty and sensitivity analyses of contaminant transport

  3. Real time source term and dose assessment

    International Nuclear Information System (INIS)

    Breznik, B.; Kovac, A.; Mlakar, P.

    2001-01-01

    The Dose Projection Programme is a tool for decision making in case of nuclear emergency. The essential input data for quick emergency evaluation in the case of hypothetical pressurised water reactor accident are following: source term, core damage assessment, fission product radioactivity, release source term and critical exposure pathways for an early phase of the release. A reduced number of radio-nuclides and simplified calculations can be used in dose calculation algorithm. Simple expert system personal computer programme has been developed for the Krsko Nuclear Power Plant for dose projection within the radius of few kilometers from the pressurised water reactor in early phase of an accident. The input data are instantaneous data of core activity, core damage indicators, release fractions, reduction factor of the release pathways, spray operation, release timing, and dispersion coefficient. Main dose projection steps are: accurate in-core radioactivity determination using reactor power input; core damage and in-containment source term assessment based on quick indications of instrumentation or on activity analysis data; user defines release pathway for typical PWR accident scenarius; dose calculation is performed only for exposure pathway critical for decision about evacuation or sheltering in early phase of an accident.(author)

  4. Source Term Model for Fine Particle Resuspension from Indoor Surfaces

    National Research Council Canada - National Science Library

    Kim, Yoojeong; Gidwani, Ashok; Sippola, Mark; Sohn, Chang W

    2008-01-01

    This Phase I effort developed a source term model for particle resuspension from indoor surfaces to be used as a source term boundary condition for CFD simulation of particle transport and dispersion in a building...

  5. Scoping Analysis of Source Term and Functional Containment Attenuation Factors

    Energy Technology Data Exchange (ETDEWEB)

    Pete Lowry

    2012-10-01

    In order to meet future regulatory requirements, the Next Generation Nuclear Plant (NGNP) Project must fully establish and validate the mechanistic modular high temperature gas-cooled reactor (HTGR) source term. This is not possible at this stage in the project, as significant uncertainties in the final design remain unresolved. In the interim, however, there is a need to establish an approximate characterization of the source term. The NGNP team developed a simplified parametric model to establish mechanistic source term estimates for a set of proposed HTGR configurations.

  6. Scoping Analysis of Source Term and Functional Containment Attenuation Factors

    Energy Technology Data Exchange (ETDEWEB)

    Pete Lowry

    2012-02-01

    In order to meet future regulatory requirements, the Next Generation Nuclear Plant (NGNP) Project must fully establish and validate the mechanistic modular high temperature gas-cooled reactor (HTGR) source term. This is not possible at this stage in the project, as significant uncertainties in the final design remain unresolved. In the interim, however, there is a need to establish an approximate characterization of the source term. The NGNP team developed a simplified parametric model to establish mechanistic source term estimates for a set of proposed HTGR configurations.

  7. Scoping Analysis of Source Term and Functional Containment Attenuation Factors

    Energy Technology Data Exchange (ETDEWEB)

    Pete Lowry

    2012-01-01

    In order to meet future regulatory requirements, the Next Generation Nuclear Plant (NGNP) Project must fully establish and validate the mechanistic modular high temperature gas-cooled reactor (HTGR) source term. This is not possible at this stage in the project, as significant uncertainties in the final design remain unresolved. In the interim, however, there is a need to establish an approximate characterization of the source term. The NGNP team developed a simplified parametric model to establish mechanistic source term estimates for a set of proposed HTGR configurations.

  8. Review of radionuclide source terms used for performance-assessment analyses

    International Nuclear Information System (INIS)

    Barnard, R.W.

    1993-06-01

    Two aspects of the radionuclide source terms used for total-system performance assessment (TSPA) analyses have been reviewed. First, a detailed radionuclide inventory (i.e., one in which the reactor type, decay, and burnup are specified) is compared with the standard source-term inventory used in prior analyses. The latter assumes a fixed ratio of pressurized-water reactor (PWR) to boiling-water reactor (BWR) spent fuel, at specific amounts of burnup and at 10-year decay. TSPA analyses have been used to compare the simplified source term with the detailed one. The TSPA-91 analyses did not show a significant difference between the source terms. Second, the radionuclides used in source terms for TSPA aqueous-transport analyses have been reviewed to select ones that are representative of the entire inventory. It is recommended that two actinide decay chains be included (the 4n+2 ''uranium'' and 4n+3 ''actinium'' decay series), since these include several radionuclides that have potentially important release and dose characteristics. In addition, several fission products are recommended for the same reason. The choice of radionuclides should be influenced by other parameter assumptions, such as the solubility and retardation of the radionuclides

  9. Actinide Source Term Program, position paper. Revision 1

    International Nuclear Information System (INIS)

    Novak, C.F.; Papenguth, H.W.; Crafts, C.C.; Dhooge, N.J.

    1994-01-01

    The Actinide Source Term represents the quantity of actinides that could be mobilized within WIPP brines and could migrate with the brines away from the disposal room vicinity. This document presents the various proposed methods for estimating this source term, with a particular focus on defining these methods and evaluating the defensibility of the models for mobile actinide concentrations. The conclusions reached in this document are: the 92 PA open-quotes expert panelclose quotes model for mobile actinide concentrations is not defensible; and, although it is extremely conservative, the open-quotes inventory limitsclose quotes model is the only existing defensible model for the actinide source term. The model effort in progress, open-quotes chemical modeling of mobile actinide concentrationsclose quotes, supported by a laboratory effort that is also in progress, is designed to provide a reasonable description of the system and be scientifically realistic and supplant the open-quotes Inventory limitsclose quotes model

  10. Development of source term PIRT of Fukushima Daiichi NPPs accident

    International Nuclear Information System (INIS)

    Suehiro, S.; Okamoto, K.

    2017-01-01

    The severe accident evaluation committee of AESJ (Atomic Energy Society of Japan) developed the thermal hydraulic PIRT (Phenomena Identification and Ranking Table) and the source term PIRT based on findings during the Fukushima Daiichi NPPs accident. These PIRTs aimed to explore the debris distribution and the current condition in the NPPs with high accuracy and to extract higher priority from the aspect of the sophistication of the analytical technology to predict the severe accident phenomena by the code. The source term PIRT was divided into 3 phases for the time domain and 9 categories for the spatial domain. The 68 phenomena were extracted and the importance from viewpoint of the source term was ranked through brainstorming and discussion. This paper describes the developed source term PIRT list and summarized the high ranked phenomena in each phase. (author)

  11. The latest results from source term research. Overview and outlook

    Energy Technology Data Exchange (ETDEWEB)

    Herranz, Luis E. [Centro de Investigaciones Energeticas Medio Ambientales y Tecnologica (CIEMAT), Madrid (Spain); Haste, Tim [Centre d' Etudes de Cadarache, Paul-Lez-Durance (France). Institut de Radioprotection et de Surete Nucleaire (IRSN); Kaerkelae, Teemu [VTT Technical Research Centre of Finland Ltd, Espoo (Finland)

    2016-12-15

    Source term research has continued internationally for more than 30 years, increasing confidence in calculations of the potential radioactive release to the environment after a severe reactor accident. Important experimental data have been obtained, mainly under international frameworks such as OECD/NEA and EURATOM. Specifically, Phebus FP provides major insights into fission product release and transport. Results are included in severe accident analysis codes. Data from international projects are being interpreted with a view to further improvements in these codes. This paper synthesizes the recent main outcomes from source term research on these topics, and on source term mitigation. It highlights knowledge gaps remaining and discusses ways to proceed. Aside from this further knowledge-driven research, there is consensus on the need to assess the source term predictive ability of current system codes, taking account of scale-up from experiment to reactor conditions.

  12. Loss of confinement of liquefied gases. Evaluation of the source term; Perte de confinement de gaz liquefies. Evaluation du terme source

    Energy Technology Data Exchange (ETDEWEB)

    Alix, P.; Novat, E.; Hocquet, J.; Bigot, J.P. [Ecole Nationale Superieure des Mines, Centre SPIN, 42 - Saint-Etienne (France)

    2001-07-01

    In this work, the states law corresponding to flow rate measurements of two-phase flows performed with five different fluid (water, butane, R11, ethyl acetate, methanol) is applied. This allows to show that the critical mass flux (which is used as source term in the scenario of loss of confinement in liquefied gas reservoirs) is a 'universal' function of the reduced initial pressure P{sub 0}{sup *}, which can be used for most of the single-constituent fluids of the processes industry. Thus it is easy to make a relatively precise estimation of the critical mass flux (uncertainty < 20% for P{sub 0}{sup *} < 15%) without the need of any model. It is shown also that no improvement of the models can be expected from the use of the vaporization kinetics. On the contrary, a qualitative consideration indicates that the use of the slip seems more promising. (J.S.)

  13. Overview of plant specific source terms and their impact on risk

    International Nuclear Information System (INIS)

    Desaedeleer, G.

    2004-01-01

    Probabilistic risk assesment and safety assessment focuses on systems and measures to prevent core meltdown, and it integrates many aspects of design and operation. It provides mapping of initiating event, frequencies onto plant damage state and through plant systems analysis, utilizes fault tree and event tree logic models, may include 'external event' analysis such as fire, flood, wind, seismic events. Percent contribution of sequences to the core damage frequency are shown for the following plants, taken as examples ZION, EDISON, OCONEE 3, SEABROOK, SIZEWELL B, MILLSTONE 3, RINGHALS 2. The presentation includes comparison of the following initiating event frequencies: loss of off-site power; small LOCA; large LOCA, steam generator tube rupture; loss of feedwater; turbine trip; reactor trip. Consequence analysis deals with: dispersion and depletion of radioactivity in the atmosphere, health effects, factors in the off-site emergency plan analyzed with codes that address the weather conditions; provision of mapping of source terms; risk diagram for early fatalities and for latent cancer fatalities

  14. Source terms derived from analyses of hypothetical accidents, 1950-1986

    International Nuclear Information System (INIS)

    Stratton, W.R.

    1987-01-01

    This paper reviews the history of reactor accident source term assumptions. After the Three Mile Island accident, a number of theoretical and experimental studies re-examined possible accident sequences and source terms. Some of these results are summarized in this paper

  15. Spent fuel assembly source term parameters

    International Nuclear Information System (INIS)

    Barrett, P.R.; Foadian, H.; Rashid, Y.R.; Seager, K.D.; Gianoulakis, S.E.

    1993-01-01

    Containment of cask contents by a transport cask is a function of the cask body, one or more closure lids, and various bolting hardware, and seals associated with the cavity closure and other containment penetrations. In addition, characteristics of cask contents that impede the ability of radionuclides to move from an origin to the external environment also provide containment. In essence, multiple release barriers exist in series in transport casks, and the magnitude of the releasable activity in the cask is considerably lower than the total activity of its contents. A source term approach accounts for the magnitude of the releasable activity available in the cask by assessing the degree of barrier resistance to release provided by material characteristics and inherent barriers that impede the release of radioactive contents. Standardized methodologies for defining the spent-fuel transport packages with specified regulations have recently been developed. An essential part of applying the source term methodology involves characterizing the response of the spent fuel under regulatory conditions of transport. Thermal and structural models of the cask and fuel are analyzed and used to predict fuel rod failure probabilities. Input to these analyses and failure evaluations cover a wide range of geometrical and material properties. An important issue in the development of these models is the sensitivity of the radioactive source term generated during transport to individual parameters such as temperature and fluence level. This paper provides a summary of sensitivity analyses concentrating on the structural response and failure predictions of the spent fuel assemblies

  16. A radiation protection initiative to map old radium sources

    International Nuclear Information System (INIS)

    Risica, S.; Grisanti, G.; Masi, R.; Melfi, A.

    2008-01-01

    Due to a legacy of past events, the Technology and Health Department of the Instituto Superiore di Sanita (ISS) has preserved an old, large archive of the allocation of radium sources in public hospitals. These sources were purchased by the Ministry of Interior first, then by the Ministry of Health, and provided to hospitals for cancer brachytherapy. After a retrieval initiative - organised in the 1980's, but discontinued some years later owing to the saturation of the temporary storage site - a considerable number of these sources remained in the hospitals. As a result of an incomplete transfer of the retrieval data, some events connected with the second world war, and the decision of some hospitals to dispose directly of their sources without informing the ISS, the archive was not completed and a series of initiatives were undertaken by the ISS to update it. On the other hand, following the concerns that arose after September 11th, 2001 about the possible criminal use of radioactive sources, the Carabinieri Environmental Care Command (CCTA) were required by the Minister of Environment to carry out a thorough investigation into all possible nuclear sources and waste in the country. Special attention was devoted to radium sources because of the high risk their loss or theft entails. For this reason, in 2004, the CCTA made an agreement with the ISS to acquire a final, updated picture of the distribution of these radium sources. In March 2007 a comprehensive report on this collaborative action and its conclusions was officially sent to both the Ministry of Health and the Ministry of the Environment. The paper describes the involvement of these two bodies in the issue, their collaborative action and the most relevant results. (author)

  17. The SSI TOOLBOX Source Term Model SOSIM - Screening for important radionuclides and parameter sensitivity analysis

    Energy Technology Data Exchange (ETDEWEB)

    Avila Moreno, R.; Barrdahl, R.; Haegg, C.

    1995-05-01

    The main objective of the present study was to carry out a screening and a sensitivity analysis of the SSI TOOLBOX source term model SOSIM. This model is a part of the SSI TOOLBOX for radiological impact assessment of the Swedish disposal concept for high-level waste KBS-3. The outputs of interest for this purpose were: the total released fraction, the time of total release, the time and value of maximum release rate, the dose rates after direct releases of the biosphere. The source term equations were derived and simple equations and methods were proposed for calculation of these. A literature survey has been performed in order to determine a characteristic variation range and a nominal value for each model parameter. In order to reduce the model uncertainties the authors recommend a change in the initial boundary condition for solution of the diffusion equation for highly soluble nuclides. 13 refs.

  18. Potential GTCC LLW sealed radiation source recycle initiatives

    International Nuclear Information System (INIS)

    Fischer, D.

    1992-04-01

    This report suggests 11 actions that have the potential to facilitate the recycling (reuse or radionuclide) of surplus commercial sealed radiation sources that would otherwise be disposed of as greater-than-Class C low-level radioactive waste. The suggestions serve as a basis for further investigation and discussion between the Department of Energy, Nuclear Regulatory Commission, Agreement States, and the commercial sector. Information is also given that describes sealed sources, how they are used, and problems associated with recycling, including legal concerns. To illustrate the nationwide recycling potential, Appendix A gives the estimated quantity and application information for sealed sources that would qualify for disposal in commercial facilities if not recycle. The report recommends that the Department of Energy initiate the organization of a forum to explore the suggested actions and other recycling possibilities

  19. Source term estimation during incident response to severe nuclear power plant accidents

    International Nuclear Information System (INIS)

    McKenna, T.J.; Glitter, J.G.

    1988-10-01

    This document presents a method of source term estimation that reflects the current understanding of source term behavior and that can be used during an event. The various methods of estimating radionuclide release to the environment (source terms) as a result of an accident at a nuclear power reactor are discussed. The major factors affecting potential radionuclide releases off site (source terms) as a result of nuclear power plant accidents are described. The quantification of these factors based on plant instrumentation also is discussed. A range of accident conditions from those within the design basis to the most severe accidents possible are included in the text. A method of gross estimation of accident source terms and their consequences off site is presented. 39 refs., 48 figs., 19 tabs

  20. Flowsheets and source terms for radioactive waste projections

    International Nuclear Information System (INIS)

    Forsberg, C.W.

    1985-03-01

    Flowsheets and source terms used to generate radioactive waste projections in the Integrated Data Base (IDB) Program are given. Volumes of each waste type generated per unit product throughput have been determined for the following facilities: uranium mining, UF 6 conversion, uranium enrichment, fuel fabrication, boiling-water reactors (BWRs), pressurized-water reactors (PWRs), and fuel reprocessing. Source terms for DOE/defense wastes have been developed. Expected wastes from typical decommissioning operations for each facility type have been determined. All wastes are also characterized by isotopic composition at time of generation and by general chemical composition. 70 references, 21 figures, 53 tables

  1. The Phebus Fission Product and Source Term International Programmes

    International Nuclear Information System (INIS)

    Clement, B.; Zeyen, R.

    2005-01-01

    The international Phebus FP programme, initiated in 1988 is one of the major research programmes on light water reactors severe accidents. After a short description of the facility and of the test matrix, the main outcomes and results of the first four integral tests are provided and analysed. Several results were unexpected and some are of importance for safety analyses, particularly concerning fuel degradation, cladding oxidation, chemical form of some fission products, especially iodine, effect of control rod materials on degradation and chemistry, iodine behaviour in the containment. Prediction capabilities of calculation tools have largely been improved as a result of this research effort. However, significant uncertainties remain for a number of phenomena, requiring detailed physical analysis and implementation of improved models in codes, sustained by a number of separate-effect experiments. This is the subject of the new Source Term programme for a better understanding of the phenomenology on important safety issues, in accordance with priorities defined in the EURSAFE project of the 5 th European framework programme aiming at reducing the uncertainties on Source Term analyses. It covers iodine chemistry, impact of boron carbide control rods degradation and oxidation, air ingress situations and fission product release from fuel. Regarding the interpretation of Phebus, an international co-operation has been established since over ten years, particularly helpful for the improvement and common understanding of severe accident phenomena. Few months ago, the Phebus community was happy to welcome representatives of a large number of organisations from the following new European countries: the Czech republic, Hungary, Lithuania, Slovakia, Slovenia and also from Bulgaria and Romania. (author)

  2. Overview of waste isoltaion safety assessment program and description of source term characterization task at PNL

    International Nuclear Information System (INIS)

    Bradley, D.

    1977-01-01

    A project is being conducted to develop and illustrate the methods and obtain the data necessary to assess the safety of long-term disposal of high-level radioactive waste in geologic formations. The methods and data will initially focus on generic geologic isolation systems but will ultimately be applied to the long-term safety assessment of specific candidate sites that are selected in the NWTS Program. The activities of waste isolation safety assessment (WISAP) are divided into six tasks: (1) Safety Assessment Concepts and Methods, (2) Disruptive Event Analysis, (3) Source Characterization, (4) Transport Modeling, (5) Transport Data and (6) Societal Acceptance

  3. Relation between source term and emergency planning for nuclear power plants

    International Nuclear Information System (INIS)

    Shi Zhongqi; Yang Ling

    1992-01-01

    Some background information of the severe accidents and source terms related to the nuclear power plant emergency planning are presented. The new source term information in NUREG-0956 and NUREG-1150, and possible changes in emergency planning requirements in U.S.A. are briefly provided. It is suggested that a principle is used in selecting source terms for establishing the emergency planning policy and a method is used in determining the Emergency Planning Zone (EPZ) size in China. Based on the research results of (1) EPZ size of PWR nuclear power plants being built in China, and (2) impact of reactor size and selected source terms on the EPZ size, it is concluded that the suggested principle and the method are suitable and feasible for PWR nuclear power plants in China

  4. 7-GeV advanced photon source beamline initiative: Conceptual design report

    International Nuclear Information System (INIS)

    1993-05-01

    The DOE is building a new generation 6-7 GeV Synchrotron Radiation Source known as the Advanced Photon Source (APS) at Argonne National Laboratory. This facility, to be completed in FY 1996, can provide 70 x-ray sources of unprecedented brightness to meet the research needs of virtually all scientific disciplines and numerous technologies. The technological research capability of the APS in the areas of energy, communications and health will enable a new partnership between the DOE and US industry. Current funding for the APS will complete the current phase of construction so that scientists can begin their applications in FY 1996. Comprehensive utilization of the unique properties of APS beams will enable cutting-edge research not currently possible. It is now appropriate to plan to construct additional radiation sources and beamline standard components to meet the excess demands of the APS users. In this APS Beamline Initiative, 2.5-m-long insertion-device x-ray sources will be built on four straight sections of the APS storage ring, and an additional four bending-magnet sources will also be put in use. The front ends for these eight x-ray sources will be built to contain and safeguard access to these bright x-ray beams. In addition, funds will be provided to build standard beamline components to meet scientific and technological research demands of the Collaborative Access Teams. The Conceptual Design Report (CDR) for the APS Beamline Initiative describes the scope of all the above technical and conventional construction and provides a detailed cost and schedule for these activities. The document also describes the preconstruction R ampersand D plans for the Beamline Initiative activities and provides the cost estimates for the required R ampersand D

  5. Evolution of source term definition and analysis

    International Nuclear Information System (INIS)

    Lutz, R.J. Jr.

    2004-01-01

    The objective of this presentation was to provide an overview of the evolution of accident fission product release analysis methodology and the obtained results; and to provide an overview of the source term implementation analysis in regulatory decisions

  6. Source term estimation during incident response to severe nuclear power plant accidents. Draft

    Energy Technology Data Exchange (ETDEWEB)

    McKenna, T J; Giitter, J

    1987-07-01

    The various methods of estimating radionuclide release to the environment (source terms) as a result of an accident at a nuclear power reactor are discussed. The major factors affecting potential radionuclide releases off site (source terms) as a result of nuclear power plant accidents are described. The quantification of these factors based on plant instrumentation also is discussed. A range of accident conditions from those within the design basis to the most severe accidents possible are included in the text. A method of gross estimation of accident source terms and their consequences off site is presented. The goal is to present a method of source term estimation that reflects the current understanding of source term behavior and that can be used during an event. (author)

  7. Source term estimation during incident response to severe nuclear power plant accidents. Draft

    International Nuclear Information System (INIS)

    McKenna, T.J.; Giitter, J.

    1987-01-01

    The various methods of estimating radionuclide release to the environment (source terms) as a result of an accident at a nuclear power reactor are discussed. The major factors affecting potential radionuclide releases off site (source terms) as a result of nuclear power plant accidents are described. The quantification of these factors based on plant instrumentation also is discussed. A range of accident conditions from those within the design basis to the most severe accidents possible are included in the text. A method of gross estimation of accident source terms and their consequences off site is presented. The goal is to present a method of source term estimation that reflects the current understanding of source term behavior and that can be used during an event. (author)

  8. Source term modelling parameters for Project-90

    International Nuclear Information System (INIS)

    Shaw, W.; Smith, G.; Worgan, K.; Hodgkinson, D.; Andersson, K.

    1992-04-01

    This document summarises the input parameters for the source term modelling within Project-90. In the first place, the parameters relate to the CALIBRE near-field code which was developed for the Swedish Nuclear Power Inspectorate's (SKI) Project-90 reference repository safety assessment exercise. An attempt has been made to give best estimate values and, where appropriate, a range which is related to variations around base cases. It should be noted that the data sets contain amendments to those considered by KBS-3. In particular, a completely new set of inventory data has been incorporated. The information given here does not constitute a complete set of parameter values for all parts of the CALIBRE code. Rather, it gives the key parameter values which are used in the constituent models within CALIBRE and the associated studies. For example, the inventory data acts as an input to the calculation of the oxidant production rates, which influence the generation of a redox front. The same data is also an initial value data set for the radionuclide migration component of CALIBRE. Similarly, the geometrical parameters of the near-field are common to both sub-models. The principal common parameters are gathered here for ease of reference and avoidance of unnecessary duplication and transcription errors. (au)

  9. The Open Source DataTurbine Initiative: Streaming Data Middleware for Environmental Observing Systems

    Science.gov (United States)

    Fountain T.; Tilak, S.; Shin, P.; Hubbard, P.; Freudinger, L.

    2009-01-01

    The Open Source DataTurbine Initiative is an international community of scientists and engineers sharing a common interest in real-time streaming data middleware and applications. The technology base of the OSDT Initiative is the DataTurbine open source middleware. Key applications of DataTurbine include coral reef monitoring, lake monitoring and limnology, biodiversity and animal tracking, structural health monitoring and earthquake engineering, airborne environmental monitoring, and environmental sustainability. DataTurbine software emerged as a commercial product in the 1990 s from collaborations between NASA and private industry. In October 2007, a grant from the USA National Science Foundation (NSF) Office of Cyberinfrastructure allowed us to transition DataTurbine from a proprietary software product into an open source software initiative. This paper describes the DataTurbine software and highlights key applications in environmental monitoring.

  10. Determination of source term for Krsko NPP extended fuel cycle

    International Nuclear Information System (INIS)

    Nemec, T.; Persic, A.; Zagar, T.; Zefran, B.

    2004-01-01

    The activity and composition of the potential radioactive releases (source term) is important in the decision making about off-site emergency measures in case of a release into environment. Power uprate of Krsko NPP during modernization in 2000 as well as changing of the fuel type and the core design have influenced the source term value. In 2003 a project of 'Jozef Stefan' Institute and Slovenian nuclear safety administration determined a plantspecific source term for new conditions of fuel type and burnup for extended fuel cycle. Calculations of activity and isotopic composition of the core have been performed with ORIGEN-ARP program. Results showed that the core activity for extended 15 months fuel cycle is slightly lower than for the 12 months cycles, mainly due to larger share of fresh fuel. (author)

  11. Accident source terms for boiling water reactors with high burnup cores.

    Energy Technology Data Exchange (ETDEWEB)

    Gauntt, Randall O.; Powers, Dana Auburn; Leonard, Mark Thomas

    2007-11-01

    The primary objective of this report is to provide the technical basis for development of recommendations for updates to the NUREG-1465 Source Term for BWRs that will extend its applicability to accidents involving high burnup (HBU) cores. However, a secondary objective is to re-examine the fundamental characteristics of the prescription for fission product release to containment described by NUREG-1465. This secondary objective is motivated by an interest to understand the extent to which research into the release and behaviors of radionuclides under accident conditions has altered best-estimate calculations of the integral response of BWRs to severe core damage sequences and the resulting radiological source terms to containment. This report, therefore, documents specific results of fission product source term analyses that will form the basis for the HBU supplement to NUREG-1465. However, commentary is also provided on observed differences between the composite results of the source term calculations performed here and those reflected NUREG-1465 itself.

  12. Selective application of revised source terms to operating nuclear power plants

    International Nuclear Information System (INIS)

    Moon, Joo Hyun; Song, Jae Hyuk; Lee, Young Wook; Ko, Hyun Seok; Kang, Chang Sun

    2001-01-01

    More than 30 years later since 1962 when TID-14844 was promulgated, there has been big change of the US NRC's regulatory position in using accident source terms for radiological assessment following a design basis accident (DBA). To replace the instantaneous source terms of TID-14844, the time-dependent source terms of NUREG-1465 was published in 1995. In the meantime, the radiological acceptance criteria for reactor site evaluation in 10 CFR Part 100 were also revised. In particular, the concept of total effective dose equivalent has been incorporated in accordance with the radiation protection standards set forth in revised 10 CFR Part 20. Subsequently, the publication of Regulatory Guide 1.183 and the revision of Standard Review Plan 15.0.1 followed in 2000, which provided the licensee of operating nuclear power reactor with the acceptable guidance of applying the revised source term. The guidance allowed the holder of an operating license issued prior to January 10, 1997 to voluntarily revise the accident source terms used in the radiological consequence analyses of DBA. Regarding to its type of application, there suggested full and selective applications, Whether it is full or selective, based upon the scope and nature of associated plant modifications being proposed, the actual application of the revised source terms to an operating plant is expected to give a large impact on its facility design basis. Considering scope and cost of the analyses required for licensing, selective application is seemed to be more appealing to an licensee of the operating plant rather than full application. In this paper, hence, the selective application methodology is reviewed and is actally applied to the assessment of offsite radiological consequence following a LOCA at Ulchin Unit 3 and 4, in order to identify and analyze the potential impacts due to application of revised source terms and to assess the considerations taken in each application prior to its actual

  13. Effect of Fuel Structure Materials on Radiation Source Term in Reactor Core Meltdown

    International Nuclear Information System (INIS)

    Jeong, Hae Sun; Ha, Kwang Soon

    2014-01-01

    The fission product (Radiation Source) releases from the reactor core into the containment is obligatorily evaluated to guarantee the safety of Nuclear Power Plant (NPP) under the hypothetical accident involving a core meltdown. The initial core inventory is used as a starting point of all radiological consequences and effects on the subsequent results of accident assessment. Hence, a proper evaluation for the inventory can be regarded as one of the most important part over the entire procedure of accident analysis. The inventory of fission products is typically evaluated on the basis of the uranium material (e.g., UO2 and USi2) loaded in nuclear fuel assembly, except for the structure materials such as the end fittings, grids, and some kinds of springs. However, the structure materials are continually activated by the neutrons generated from the nuclear fission, and some nuclides of them (e.g., 14 C and 60 Co) can significantly influence on accident assessment. During the severe core accident, the structure components can be also melted with the melting points of temperature relatively lower than uranium material. A series of the calculation were performed by using ORIGEN-S module in SCALE 6.1 package code system. The total activity in each part of structure materials was specifically analyzed from these calculations. The fission product inventory is generally evaluated based on the uranium materials of fuel only, even though the structure components of the assembly are continually activated by the neutrons generated from the nuclear fission. In this study, the activation calculation of the fuel structure materials was performed for the initial source term assessment in the accident of reactor core meltdown. As a result, the lower end fitting and the upper plenum greatly contribute to the total activity except for the cladding material. The nuclides of 56 Mn, '5 1 Cr, 55 Fe, 58 Co, 54 Mn, and 60 Co are analyzed to mainly effect on the activity. This result

  14. Directional Unfolded Source Term (DUST) for Compton Cameras.

    Energy Technology Data Exchange (ETDEWEB)

    Mitchell, Dean J.; Mitchell, Dean J.; Horne, Steven M.; O' Brien, Sean; Thoreson, Gregory G

    2018-03-01

    A Directional Unfolded Source Term (DUST) algorithm was developed to enable improved spectral analysis capabilities using data collected by Compton cameras. Achieving this objective required modification of the detector response function in the Gamma Detector Response and Analysis Software (GADRAS). Experimental data that were collected in support of this work include measurements of calibration sources at a range of separation distances and cylindrical depleted uranium castings.

  15. Development of source term evaluation method for Korean Next Generation Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Keon Jae; Cheong, Jae Hak; Park, Jin Baek; Kim, Guk Gee [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of)

    1997-10-15

    This project had investigate several design features of radioactive waste processing system and method to predict nuclide concentration at primary coolant basic concept of next generation reactor and safety goals at the former phase. In this project several prediction methods of source term are evaluated conglomerately and detailed contents of this project are : model evaluation of nuclide concentration at Reactor Coolant System, evaluation of primary and secondary coolant concentration of reference Nuclear Power Plant(NPP), investigation of prediction parameter of source term evaluation, basic parameter of PWR, operational parameter, respectively, radionuclide removal system and adjustment values of reference NPP, suggestion of source term prediction method of next generation NPP.

  16. Severe accident source term reassessment

    International Nuclear Information System (INIS)

    Hazzan, M.J.; Gardner, R.; Warman, E.A.; Jacobs, S.B.

    1987-01-01

    This paper summarizes the status of the reassessment of severe reactor accident source terms, which are defined as the quantity, type, and timing of fission product releases from such accidents. Concentration is on the major results and conclusions of analyses with modern methods for both pressurized water reactors (PWRs) and boiling water reactors (BWRs), and the special case of containment bypass. Some distinctions are drawn between analyses for PWRs and BWRs. In general, the more the matter is examined, the consequences, or probability of serious consequences, seem to be less. (author)

  17. Source term estimation via monitoring data and its implementation to the RODOS system

    International Nuclear Information System (INIS)

    Bohunova, J.; Duranova, T.

    2000-01-01

    A methodology and computer code for interpretation of environmental data, i.e. source term assessment, from on-line environmental monitoring network was developed. The method is based on the conversion of measured dose rates to the source term, i.e. airborne radioactivity release rate, taking into account real meteorological data and location of the monitoring points. The bootstrap estimation methodology and bipivot method to estimate the source term from on-site gamma dose rate monitors is used. The mentioned methods provide an estimate of the mean value of the source term and a confidence interval for it. (author)

  18. Source term estimation for small sized HTRs

    International Nuclear Information System (INIS)

    Moormann, R.

    1992-08-01

    Accidents which have to be considered are core heat-up, reactivity transients, water of air ingress and primary circuit depressurization. The main effort of this paper belongs to water/air ingress and depressurization, which requires consideration of fission product plateout under normal operation conditions; for the latter it is clearly shown, that absorption (penetration) mechanisms are much less important than assumed sometimes in the past. Source term estimation procedures for core heat-up events are shortly reviewed; reactivity transients are apparently covered by them. Besides a general literature survey including identification of areas with insufficient knowledge this paper contains some estimations on the thermomechanical behaviour of fission products in water in air ingress accidents. Typical source term examples are also presented. In an appendix, evaluations of the AVR experiments VAMPYR-I and -II with respect to plateout and fission product filter efficiency are outlined and used for a validation step of the new plateout code SPATRA. (orig.)

  19. Using Bayesian Belief Network (BBN) modelling for Rapid Source Term Prediction. RASTEP Phase 1

    International Nuclear Information System (INIS)

    Knochenhauer, M.; Swaling, V.H.; Alfheim, P.

    2012-09-01

    The project is connected to the development of RASTEP, a computerized source term prediction tool aimed at providing a basis for improving off-site emergency management. RASTEP uses Bayesian belief networks (BBN) to model severe accident progression in a nuclear power plant in combination with pre-calculated source terms (i.e., amount, timing, and pathway of released radio-nuclides). The output is a set of possible source terms with associated probabilities. In the NKS project, a number of complex issues associated with the integration of probabilistic and deterministic analyses are addressed. This includes issues related to the method for estimating source terms, signal validation, and sensitivity analysis. One major task within Phase 1 of the project addressed the problem of how to make the source term module flexible enough to give reliable and valid output throughout the accident scenario. Of the alternatives evaluated, it is recommended that RASTEP is connected to a fast running source term prediction code, e.g., MARS, with a possibility of updating source terms based on real-time observations. (Author)

  20. Using Bayesian Belief Network (BBN) modelling for Rapid Source Term Prediction. RASTEP Phase 1

    Energy Technology Data Exchange (ETDEWEB)

    Knochenhauer, M.; Swaling, V.H.; Alfheim, P. [Scandpower AB, Sundbyberg (Sweden)

    2012-09-15

    The project is connected to the development of RASTEP, a computerized source term prediction tool aimed at providing a basis for improving off-site emergency management. RASTEP uses Bayesian belief networks (BBN) to model severe accident progression in a nuclear power plant in combination with pre-calculated source terms (i.e., amount, timing, and pathway of released radio-nuclides). The output is a set of possible source terms with associated probabilities. In the NKS project, a number of complex issues associated with the integration of probabilistic and deterministic analyses are addressed. This includes issues related to the method for estimating source terms, signal validation, and sensitivity analysis. One major task within Phase 1 of the project addressed the problem of how to make the source term module flexible enough to give reliable and valid output throughout the accident scenario. Of the alternatives evaluated, it is recommended that RASTEP is connected to a fast running source term prediction code, e.g., MARS, with a possibility of updating source terms based on real-time observations. (Author)

  1. Initial operation of the CW 8X H- ion source discharge

    International Nuclear Information System (INIS)

    Smith, H.V. Jr.; Allison, P.; Geisik, C.; Schmitt, D.R.; Schneider, J.D.; Stelzer, J.E.

    1993-01-01

    A pulsed 8Χ source was built and the H - beam current, emittance, and power efficiency were measured. These results were promising, so a cooled, dc version designed for operation at arc power levels up to 30 kW was built. Testing of the CW 8Χ source discharge is underway. The design dc power loading on the cathode surface is 900 W/cm 2 , considerably higher than achieved in any pervious Penning surface-plasma source (SPS). Thus, the electrode surfaces are cooled with pressurized, hot water. We describe the source and present the initial operating experience and arc test results

  2. Initial operation of the CW 8X H- ion source discharge

    International Nuclear Information System (INIS)

    Smith, H.V. Jr.; Allison, P.; Geisik, C.; Schmitt, D.R.; Schneider, J.D.; Stelzer, J.E.

    1993-01-01

    A pulsed 8X source was built and the H - beam current, emittance, and power efficiency were measured. These results were promising, so a cooled, dc version designed for operation at arc power levels up to 30 kW was built. Testing of the CW 8X source discharge is underway. The design dc power loading on the cathode surface is 900 W/cm 2 , considerably higher than achieved in any previous Penning surface-plasma source (SPS). Thus, the electrode surfaces are cooled with pressurized, hot water. The authors describe the source and present the initial operating experience and arc test results

  3. Source terms associated with two severe accident sequences in a 900 MWe PWR

    International Nuclear Information System (INIS)

    Fermandjian, J.; Evrard, J.M.; Berthion, Y.; Lhiaubet, G.; Lucas, M.

    1983-12-01

    Hypothetical accidents taken into account in PWR risk assessment result in fission product release from the fuel, transfer through the primary circuit, transfer into the reactor containment building (RCB) and finally release to the environment. The objective of this paper is to define the characteristics of the source term (noble gases, particles and volatile iodine forms) released from the reactor containment building during two dominant core-melt accident sequences: S 2 CD and TLB according to the ''Reactor Safety Study'' terminology. The reactor chosen for this study is a French 900 MWe PWR unit. The reactor building is a prestressed concrete containment with an internal liner. The first core-melt accident sequence is a 2-break loss-of-coolant accident on the cold leg, with failure of both system and the containment spray system. The second one is a transient initiated by a loss of offsite and onsite power supply and auxiliary feedwater system. These two sequences have been chosen because they are representative of risk dominant scenarios. Source terms associated with hypothetical core-melt accidents S 2 CD and TLB in a French PWR -900 MWe- have been performed using French computer codes (in particular, JERICHO Code for containment response analysis and AEROSOLS/31 for aerosol behavior in the containment)

  4. Development of source term evaluation method for Korean Next Generation Reactor(III)

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Geon Jae; Park, Jin Baek; Lee, Yeong Il; Song, Min Cheonl; Lee, Ho Jin [Korea Advanced Institue of Science and Technology, Taejon (Korea, Republic of)

    1998-06-15

    This project had investigated irradiation characteristics of MOX fuel method to predict nuclide concentration at primary and secondary coolant using a core containing 100% of all MOX fuel and development of source term evaluation tool. In this study, several prediction methods of source term are evaluated. Detailed contents of this project are : an evaluation of model for nuclear concentration at Reactor Coolant System, evaluation of primary and secondary coolant concentration of reference Nuclear Power Plant using purely MOX fuel, suggestion of source term prediction method of NPP with a core using MOX fuel.

  5. Freeing Crop Genetics through the Open Source Seed Initiative.

    Directory of Open Access Journals (Sweden)

    Claire H Luby

    2016-04-01

    Full Text Available For millennia, seeds have been freely available to use for farming and plant breeding without restriction. Within the past century, however, intellectual property rights (IPRs have threatened this tradition. In response, a movement has emerged to counter the trend toward increasing consolidation of control and ownership of plant germplasm. One effort, the Open Source Seed Initiative (OSSI, www.osseeds.org, aims to ensure access to crop genetic resources by embracing an open source mechanism that fosters exchange and innovation among farmers, plant breeders, and seed companies. Plant breeders across many sectors have taken the OSSI Pledge to create a protected commons of plant germplasm for future generations.

  6. Freeing Crop Genetics through the Open Source Seed Initiative.

    Science.gov (United States)

    Luby, Claire H; Goldman, Irwin L

    2016-04-01

    For millennia, seeds have been freely available to use for farming and plant breeding without restriction. Within the past century, however, intellectual property rights (IPRs) have threatened this tradition. In response, a movement has emerged to counter the trend toward increasing consolidation of control and ownership of plant germplasm. One effort, the Open Source Seed Initiative (OSSI, www.osseeds.org), aims to ensure access to crop genetic resources by embracing an open source mechanism that fosters exchange and innovation among farmers, plant breeders, and seed companies. Plant breeders across many sectors have taken the OSSI Pledge to create a protected commons of plant germplasm for future generations.

  7. STACE: Source Term Analyses for Containment Evaluations of transport casks

    International Nuclear Information System (INIS)

    Seager, K.D.; Gianoulakis, S.E.; Barrett, P.R.; Rashid, Y.R.; Reardon, P.C.

    1992-01-01

    Following the guidance of ANSI N14.5, the STACE methodology provides a technically defensible means for estimating maximum permissible leakage rates. These containment criteria attempt to reflect the true radiological hazard by performing a detailed examination of the spent fuel, CRUD, and residual contamination contributions to the releasable source term. The evaluation of the spent fuel contribution to the source term has been modeled fairly accurately using the STACE methodology. The structural model predicts the cask drop load history, the mechanical response of the fuel assembly, and the probability of cladding breach. These data are then used to predict the amount of fission gas, volatile species, and fuel fines that are releasable from the cask. There are some areas where data are sparse or lacking (e.g., the quantity and size distribution of fuel rod breaches) in which experimental validation is planned. The CRUD spallation fraction is the major area where no quantitative data has been found; therefore, this also requires experimental validation. In the interim, STACE conservatively assumes a 100% spallation fraction for computing the releasable activity. The source term methodology also conservatively assumes that there is 1 Ci of residual contamination available for release in the transport cask. However, residual contamination is still by far the smallest contributor to the source term activity

  8. Perspectives on source terms based on early research and development

    International Nuclear Information System (INIS)

    Pressesky, A.J.

    1985-07-01

    This report presents an overview of the key documentation of the research and development programs relevant to the source term issue which were undertaken by the Atomic Energy Commission between 1950 and 1970. The source term is taken to be the amount, composition (physical and chemical), and timing of the projected release of radioactivity to the environment in the hypothetical event of a severe reactor accident in a light water reactor of the type currently being licensed, built and operated. The objective is to illuminate and provide perspectives on (a) the maturity of the technical data base and the analytical methodology, (b) the extent to which remaining conservatisms can be applied to compensate for uncertainties, (c) the purpose for which the technology and methodology will be used, and (d) the need to keep problems and uncertainties in proper perspective. Comments that can provide some context for the difficult programmatic choices to be made are included, and technical considerations that may be inadequately applied or neglected in some current source term calculations were studied. This review has not uncovered any significant technical considerations that have been omitted or are being inadequately treated in current source term analyses, except perhaps the contribution made to in-containment aerosols by coolant comminution upon escape at pressure from the reactor coolant system. 11 refs

  9. Source term determination from subcritical multiplication measurements at Koral-1 reactor

    International Nuclear Information System (INIS)

    Blazquez, J.B.; Barrado, J.M.

    1978-01-01

    By using an AmBe neutron source two independent procedures have been settled for the zero-power experimental fast-reactor Coral-1 in order to measure the source term which appears in the point kinetical equations. In the first one, the source term is measured when the reactor is just critical with source by taking advantage of the wide range of the linear approach to critical for Coral-1. In the second one, the measurement is made in subcritical state by making use of the previous calibrated control rods. Several applications are also included such as the measurement of the detector dead time, the determinations of the reactivity of small samples and the shape of the neutron importance of the source. (author)

  10. Ion sources for initial use at the Holifield radioactive ion beam facility

    International Nuclear Information System (INIS)

    Alton, G.D.

    1994-01-01

    The Holifield Radioactive Ion Beam Facility (HRIBF) now under construction at the Oak Ridge National Laboratory will use the 25-MV tandem accelerator for the acceleration of radioactive ion beams to energies appropriate for research in nuclear physics; negative ion beams are, therefore, required for injection into the tandem accelerator. Because charge exchange is an efficient means for converting initially positive ion beams to negative ion beams, both positive and negative ion sources are viable options for use at the facility; the choice of the type of ion source will depend on the overall efficiency for generating the radioactive species of interest. A high-temperature version of the CERN-ISOLDE positive ion source has been selected and a modified version of the source designed and fabricated for initial use at the HRIBF because of its low emittance, relatively high ionization efficiencies and species versatility, and because it has been engineered for remote installation, removal and servicing as required for safe handling in a high-radiation-level ISOL facility. Prototype plasma-sputter negative ion sources and negative surfaceionization sources are also under design consideration for generating negative radioactive ion beams from high electron-affinity elements. A brief review of the HRIBF will be presented, followed by a detailed description of the design features, operational characteristics, ionization efficiencies, and beam qualities (emittances) of these sources

  11. Source terms in relation to air cleaning

    International Nuclear Information System (INIS)

    Bernero, R.M.

    1985-01-01

    There are two sets of source terms for consideration in air cleaning, those for routine releases and those for accident releases. With about 1000 reactor years of commercial operating experience in the US done, there is an excellent data base for routine and expected transient releases. Specifications for air cleaning can be based on this body of experience with confidence. Specifications for air cleaning in accident situations is another matter. Recent investigations of severe accident behavior are offering a new basis for source terms and air cleaning specifications. Reports by many experts in the field describe an accident environment notably different from previous models. It is an atmosphere heavy with aerosols, both radioactive and inert. Temperatures are sometimes very high; radioiodine is typically in the form of cesium iodide aerosol particles; other nuclides, such as tellurium, are also important aerosols. Some of the present air cleaning requirements may be very important in light of these new accident behavior models. Others may be wasteful or even counterproductive. The use of the new data on accident behavior models to reevaluate requirements promptly is discussed

  12. Source-term reevaluation for US commercial nuclear power reactors: a status report

    International Nuclear Information System (INIS)

    Herzenberg, C.L.; Ball, J.R.; Ramaswami, D.

    1984-12-01

    Only results that had been discussed publicly, had been published in the open literature, or were available in preliminary reports as of September 30, 1984, are included here. More than 20 organizations are participating in source-term programs, which have been undertaken to examine severe accident phenomena in light-water power reactors (including the chemical and physical behavior of fission products under accident conditions), update and reevaluate source terms, and resolve differences between predictions and observations of radiation releases and related phenomena. Results from these source-term activities have been documented in over 100 publications to date

  13. Recovery Act: Tennessee Energy Efficient Schools Initiative Ground Source Heat Pump Program

    Energy Technology Data Exchange (ETDEWEB)

    Townsend, Terry [Townsend Engineering, Inc., Davenport, IA (United States); Slusher, Scott [Townsend Engineering, Inc., Davenport, IA (United States)

    2017-04-24

    The Tennessee Energy Efficient Schools Initiative (EESI) Hybrid-Water Source Heat Pump (HY-GSHP) Program sought to provide installation costs and operation costs for different Hybrid water source heat pump systems’ configurations so that other State of Tennessee School Districts will have a resource for comparison purposes if considering a geothermal system.

  14. Accident source terms for Light-Water Nuclear Power Plants. Final report

    International Nuclear Information System (INIS)

    Soffer, L.; Burson, S.B.; Ferrell, C.M.; Lee, R.Y.; Ridgely, J.N.

    1995-02-01

    In 1962 tile US Atomic Energy Commission published TID-14844, ''Calculation of Distance Factors for Power and Test Reactors'' which specified a release of fission products from the core to the reactor containment for a postulated accident involving ''substantial meltdown of the core''. This ''source term'', tile basis for tile NRC's Regulatory Guides 1.3 and 1.4, has been used to determine compliance with tile NRC's reactor site criteria, 10 CFR Part 100, and to evaluate other important plant performance requirements. During the past 30 years substantial additional information on fission product releases has been developed based on significant severe accident research. This document utilizes this research by providing more realistic estimates of the ''source term'' release into containment, in terms of timing, nuclide types, quantities and chemical form, given a severe core-melt accident. This revised ''source term'' is to be applied to the design of future light water reactors (LWRs). Current LWR licensees may voluntarily propose applications based upon it

  15. Reassessment of the technical bases for estimating source terms. Draft report for comment

    International Nuclear Information System (INIS)

    Silberberg, M.; Mitchell, J.A.; Meyer, R.O.; Pasedag, W.F.; Ryder, C.P.; Peabody, C.A.; Jankowski, M.W.

    1985-07-01

    NUREG-0956 describes the NRC staff and contractor efforts to reassess and update the agency's analytical procedures for estimating accident source terms for nuclear power plants. The effort included development of a new source term analytical procedure - a set of computer codes - that is intended to replace the methodology of the Reactor Safety Study (WASH-1400) and to be used in reassessing the use of TID-14844 assumptions (10 CFR 100). NUREG-0956 describes the development of these codes, the demonstration of the codes to calculate source terms for specific cases, the peer review of this work, some perspectives on the overall impact of new source terms on plant risks, the plans for related research projects, and the conclusions and recommendations resulting from the effort

  16. New method to determine initial surface water displacement at tsunami source

    Science.gov (United States)

    Lavrentyev, Mikhail; Romanenko, Alexey; Tatarintsev, Pavel

    2013-04-01

    Friday, March 11, 2011 at 05:46:23 UTC, Japan was struck by an 8.9-magnitude earthquake near its Northeastern coast. This is one of the largest earthquakes that Japan has ever experienced. Tsunami waves swept away houses and cars and caused massive human losses. To predict tsunami wave parameters better and faster, we propose to improve data inversion scheme and achieve the performance gain of data processing. One of the reasons of inaccurate predictions of tsunami parameters is that very little information is available about the initial disturbance of the sea bed at tsunami source. In this paper, we suggest a new way of improving the quality of tsunami source parameters prediction. Modern computational technologies can accurately calculate tsunami wave propagation over the deep ocean provided that the initial displacement (perturbation of the sea bed at tsunami source) is known [4]. Direct geophysical measurements provide the location of an earthquake hypocenter and its magnitude (the released energy evaluation). Among the methods of determination of initial displacement the following ones should be considered. Calculation through the known fault structure and available seismic information. This method is widely used and provides useful information. However, even if the exact knowledge about rock blocks shifts is given, recalculation in terms of sea bed displacement is needed. This results in a certain number of errors. GPS data analysis. This method was developed after the December 2004 event in the Indian Ocean. A good correlation between dry land based GPS sensors and tsunami wave parameters was observed in the particular case of the West coast of Sumatra, Indonesia. This approach is very unique and can hardly been used in other geo locations. Satellite image analysis. The resolution of modern satellite images has dramatically improved. In the future, correct data of sea surface displacement will probably be available in real time, right after a tsunamigenic

  17. Methodology for and uses of a radiological source term assessment for potential impacts to stormwater and groundwater

    International Nuclear Information System (INIS)

    Teare, A.; Hansen, K.; DeWilde, J.; Yu, L.; Killey, D.

    2001-01-01

    A Radiological Source Term Assessment (RSTA) was conducted by Ontario Power Generation Inc. (OPG) at the Pickering Nuclear Generating Station (PNGS). Tritium had been identified in the groundwater at several locations under the station, and OPG initiated the RSTA as part of its ongoing efforts to improve operations and to identify potential sources of radionuclide impact to groundwater and stormwater at the station. The RSTA provides a systematic approach to collecting information and assessing environmental risk for radioactive contaminants based on a ranking system developed for the purpose. This paper provides an overview of the RSTA focusing on the investigative approach and how it was applied. This approach can find application at other generating stations. (author)

  18. Pennsylvania Source Term Tracking System

    International Nuclear Information System (INIS)

    1992-08-01

    The Pennsylvania Source Term Tracking System tabulates surveys received from radioactive waste generators in the Commonwealth of radioactive waste is collected each quarter from generators using the Low-Level Radioactive Waste Management Quarterly Report Form (hereafter called the survey) and then entered into the tracking system data base. This personal computer-based tracking system can generate 12 types of tracking reports. The first four sections of this reference manual supply complete instructions for installing and setting up the tracking system on a PC. Section 5 presents instructions for entering quarterly survey data, and Section 6 discusses generating reports. The appendix includes samples of each report

  19. Using Bayesian Belief Network (BBN) modelling for rapid source term prediction. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Knochenhauer, M.; Swaling, V.H.; Dedda, F.D.; Hansson, F.; Sjoekvist, S.; Sunnegaerd, K. [Lloyd' s Register Consulting AB, Sundbyberg (Sweden)

    2013-10-15

    The project presented in this report deals with a number of complex issues related to the development of a tool for rapid source term prediction (RASTEP), based on a plant model represented as a Bayesian belief network (BBN) and a source term module which is used for assigning relevant source terms to BBN end states. Thus, RASTEP uses a BBN to model severe accident progression in a nuclear power plant in combination with pre-calculated source terms (i.e., amount, composition, timing, and release path of released radio-nuclides). The output is a set of possible source terms with associated probabilities. One major issue has been associated with the integration of probabilistic and deterministic analyses are addressed, dealing with the challenge of making the source term determination flexible enough to give reliable and valid output throughout the accident scenario. The potential for connecting RASTEP to a fast running source term prediction code has been explored, as well as alternative ways of improving the deterministic connections of the tool. As part of the investigation, a comparison of two deterministic severe accident analysis codes has been performed. A second important task has been to develop a general method where experts' beliefs can be included in a systematic way when defining the conditional probability tables (CPTs) in the BBN. The proposed method includes expert judgement in a systematic way when defining the CPTs of a BBN. Using this iterative method results in a reliable BBN even though expert judgements, with their associated uncertainties, have been used. It also simplifies verification and validation of the considerable amounts of quantitative data included in a BBN. (Author)

  20. Using Bayesian Belief Network (BBN) modelling for rapid source term prediction. Final report

    International Nuclear Information System (INIS)

    Knochenhauer, M.; Swaling, V.H.; Dedda, F.D.; Hansson, F.; Sjoekvist, S.; Sunnegaerd, K.

    2013-10-01

    The project presented in this report deals with a number of complex issues related to the development of a tool for rapid source term prediction (RASTEP), based on a plant model represented as a Bayesian belief network (BBN) and a source term module which is used for assigning relevant source terms to BBN end states. Thus, RASTEP uses a BBN to model severe accident progression in a nuclear power plant in combination with pre-calculated source terms (i.e., amount, composition, timing, and release path of released radio-nuclides). The output is a set of possible source terms with associated probabilities. One major issue has been associated with the integration of probabilistic and deterministic analyses are addressed, dealing with the challenge of making the source term determination flexible enough to give reliable and valid output throughout the accident scenario. The potential for connecting RASTEP to a fast running source term prediction code has been explored, as well as alternative ways of improving the deterministic connections of the tool. As part of the investigation, a comparison of two deterministic severe accident analysis codes has been performed. A second important task has been to develop a general method where experts' beliefs can be included in a systematic way when defining the conditional probability tables (CPTs) in the BBN. The proposed method includes expert judgement in a systematic way when defining the CPTs of a BBN. Using this iterative method results in a reliable BBN even though expert judgements, with their associated uncertainties, have been used. It also simplifies verification and validation of the considerable amounts of quantitative data included in a BBN. (Author)

  1. Source term model evaluations for the low-level waste facility performance assessment

    Energy Technology Data Exchange (ETDEWEB)

    Yim, M.S.; Su, S.I. [North Carolina State Univ., Raleigh, NC (United States)

    1995-12-31

    The estimation of release of radionuclides from various waste forms to the bottom boundary of the waste disposal facility (source term) is one of the most important aspects of LLW facility performance assessment. In this work, several currently used source term models are comparatively evaluated for the release of carbon-14 based on a test case problem. The models compared include PRESTO-EPA-CPG, IMPACTS, DUST and NEFTRAN-II. Major differences in assumptions and approaches between the models are described and key parameters are identified through sensitivity analysis. The source term results from different models are compared and other concerns or suggestions are discussed.

  2. An investigation of the closure problem applied to reactor accident source terms

    International Nuclear Information System (INIS)

    Brearley, I.R.; Nixon, W.; Hayns, M.R.

    1987-01-01

    The closure problem, as considered here, focuses attention on the question of when in current research programmes enough has been learned about the source terms for reactor accident releases. Noting that current research is tending to reduce the estimated magnitude of the aerosol component of atmospheric, accidental releases, several possible criteria for closure are suggested. Moreover, using the reactor accident consequence model CRACUK, the effect of gradually reducing the aerosol release fractions of a pressurized water reactor (PWR2) source term (as defined in the WASH-1400 study) is investigated and the implications of applying the suggested criteria to current source term research discussed. (author)

  3. Source terms: an investigation of uncertainties, magnitudes, and recommendations for research. [PWR; BWR

    Energy Technology Data Exchange (ETDEWEB)

    Levine, S.; Kaiser, G. D.; Arcieri, W. C.; Firstenberg, H.; Fulford, P. J.; Lam, P. S.; Ritzman, R. L.; Schmidt, E. R.

    1982-03-01

    The purpose of this document is to assess the state of knowledge and expert opinions that exist about fission product source terms from potential nuclear power plant accidents. This is so that recommendations can be made for research and analyses which have the potential to reduce the uncertainties in these estimated source terms and to derive improved methods for predicting their magnitudes. The main reasons for writing this report are to indicate the major uncertainties involved in defining realistic source terms that could arise from severe reactor accidents, to determine which factors would have the most significant impact on public risks and emergency planning, and to suggest research and analyses that could result in the reduction of these uncertainties. Source terms used in the conventional consequence calculations in the licensing process are not explicitly addressed.

  4. Data assimilation and source term estimation during the early phase of a nuclear accident

    Energy Technology Data Exchange (ETDEWEB)

    Golubenkov, A.; Borodin, R. [SPA Typhoon, Emergency Centre (Russian Federation); Sohier, A.; Rojas Palma, C. [Centre de l`Etude de l`Energie Nucleaire, Mol (Belgium)

    1996-02-01

    The mathematical/physical base of possible methods to model the source term during an accidental release of radionuclides is discussed. Knowledge of the source term is important in view of optimizing urgent countermeasures to the population. In most cases however, it will be impossible to assess directly the release dynamics. Therefore methods are under development in which the source term is modelled, based on the comparison of off-site monitoring data and model predictions using an atmospheric dispersion model. The degree of agreement between the measured and calculated characteristics of the radioactive contamination of the air and the ground surface is an important criterion in this process. Due to the inherent complexity, some geometrical transformations taking space-time discrepancies between observed and modelled contamination fields are defined before the source term is adapted. This work describes the developed algorithms which are also tested against data from some tracer experiments performed in the past. This method is also used to reconstruct the dynamics of the Chernobyl source term. Finally this report presents a concept of software to reconstruct a multi-isotopic source term in real-time.

  5. Data assimilation and source term estimation during the early phase of a nuclear accident

    International Nuclear Information System (INIS)

    Golubenkov, A.; Borodin, R.; Sohier, A.; Rojas Palma, C.

    1996-02-01

    The mathematical/physical base of possible methods to model the source term during an accidental release of radionuclides is discussed. Knowledge of the source term is important in view of optimizing urgent countermeasures to the population. In most cases however, it will be impossible to assess directly the release dynamics. Therefore methods are under development in which the source term is modelled, based on the comparison of off-site monitoring data and model predictions using an atmospheric dispersion model. The degree of agreement between the measured and calculated characteristics of the radioactive contamination of the air and the ground surface is an important criterion in this process. Due to the inherent complexity, some geometrical transformations taking space-time discrepancies between observed and modelled contamination fields are defined before the source term is adapted. This work describes the developed algorithms which are also tested against data from some tracer experiments performed in the past. This method is also used to reconstruct the dynamics of the Chernobyl source term. Finally this report presents a concept of software to reconstruct a multi-isotopic source term in real-time

  6. Revised reactor accident source terms in the U.S. and implementation for light water reactors

    International Nuclear Information System (INIS)

    Soffer, L.; Lee, J.Y.

    1992-01-01

    Current NRC reactor accident source terms used for licensing are contained in Regulatory Guides 1.3 and 1.4 and specify that 100 % of the core inventory of noble gases and 25 % of the iodine fission products are assumed to be instantaneously available for release from the containment. The chemical form of the iodine fission products is also assumed to be predominantly elemental (I 2 ) iodine. These assumptions have strongly affected present nuclear plant designs. Severe accident research results have confirmed that although the current source term is very substantial and has resulted in a very high level of plant capability, the present source term is no longer compatible with a realistic understanding of severe accidents. The NRC has issued a proposed revision of the reactor accident source terms as part of several regulatory activities to incorporate severe accident insights for future plants. A revision to 10 CFR 100 is also being proposed to specify site criteria directly and to eliminate source terms and doses for site evaluation. Reactor source terms will continue to be important in evaluating plant designs. Although intended primarily for future plants, existing and evolutionary power plants may voluntarily apply revised accident source term insights as well in licensing. The proposed revised accident source terms are presented in terms of fission product composition, magnitude, timing and iodine chemical form. Some implications for light water reactors are discussed. (author)

  7. EDF source term reduction project main outcomes and further developments

    International Nuclear Information System (INIS)

    Ranchoux, Gilles; Bonnefon, Julien; Benfarah, Moez; Wintergerst Matthieu; Gressier, Frederic; Leclercq, Stephanie

    2012-09-01

    The dose reduction is a strategic purpose for EDF in link with the stakes of, nuclear acceptability, respect of regulation and productivity gains. This consists not only in improving the reactor shutdown organization (time spent in control area, biological shielding,...) but also in improving the radiological state of the unit and the efficiency of the source term reduction operations. Since 2003, EDF has been running an innovative project called 'Source Term Reduction' federating the different EDF research and engineering centers in order to: - participate to the long term view about Radiological Protection issues (international feedback analyses), - develop contamination prediction tools (OSCAR software) suitable for the industrial needs (operating units and EPR design), - develop scientific models useful for the understanding of contamination mechanisms to support the strategic decision processes, - carry on with updating and analyzing of contamination measurements feedback in corrosion products (EMECC and CZT campaigns), - carry on with the operational support at short or middle term by optimizing startup and shutdown processes, pre-oxidation or and by improving purification efficiency or material characteristics. This paper will show in a first part the main 2011 results in occupational exposure (collective and individual dose, RCS index...). In a second part, an overview of the main EDF outcomes of the last 3 years in the field of source term reduction will be presented. Future developments extended to contamination issues in EDF NPPs will be also pointed out in this paper. (authors)

  8. Backup Sourcing Decisions for Coping with Supply Disruptions under Long-Term Horizons

    Directory of Open Access Journals (Sweden)

    Jing Hou

    2016-01-01

    Full Text Available This paper studies a buyer’s inventory control problem under a long-term horizon. The buyer has one major supplier that is prone to disruption risks and one backup supplier with higher wholesale price. Two kinds of sourcing methods are available for the buyer: single sourcing with/without contingent supply and dual sourcing. In contingent sourcing, the backup supplier is capacitated and/or has yield uncertainty, whereas in dual sourcing the backup supplier has an incentive to offer output flexibility during disrupted periods. The buyer’s expected cost functions and the optimal base-stock levels using each sourcing method under long-term horizon are obtained, respectively. The effects of three risk parameters, disruption probability, contingent capacity or uncertainty, and backup flexibility, are examined using comparative studies and numerical computations. Four sourcing methods, namely, single sourcing with contingent supply, dual sourcing, and single sourcing from either of the two suppliers, are also compared. These findings can be used as a valuable guideline for companies to select an appropriate sourcing strategy under supply disruption risks.

  9. A simplistic view of the iodine chemistry influence on source term assessment

    International Nuclear Information System (INIS)

    Herranz, L.E.; Rodriguez, J.J.

    1994-01-01

    The intrinsic characteristics of iodine make it a relevant concern as to its potential radiobiological impact in case of a hypothetical severe accident in nuclear power plants. This paper summarizes the major results drawn from a very simple but illustrative calculation exercise aimed at weighing how significant could be taking iodine chemistry in containment into account for source term assessments in case of a postulated severe reactor accident. The scenario chosen as representative of expected conditions in containment was LA-4 test of LACE programme. Several approximations and hypothesis concerning the scenario were necessary. Iodine chemistry analyses were performed with IODE code, as long as thermalhydraulic and aerosol behaviour analyses, providing initial and boundary conditions for iodine calculations, were carried out with CONTEMPT4/MOD5 and NAUA/MOD5 codes, respectively. In general, the results obtained agreed qualitatively with the current knowledge on the area; from a quantitative point of view, one of the major results was that iodine chemistry on acidic conditions could provide a substantial increase in the leaked mass from containment under the postulated circumstances. Hence, this study underlines the need of including iodine chemistry in source tenn assessments. (author)

  10. Reevaluation of HFIR source term: Supplement 2

    International Nuclear Information System (INIS)

    Thomas, W.E.

    1986-11-01

    The HFIR source term has been reevaluated to assess the impact of the increase in core lifetime from 15 to 24 days. Calculations were made to determine the nuclide activities of the iodines, noble gases, and other fission products. The results show that there is no significant change in off-site dose due to the increased fuel cycle for the release scenario postulated in ORNL-3573

  11. A critical assessment of flux and source term closures in shallow water models with porosity for urban flood simulations

    Science.gov (United States)

    Guinot, Vincent

    2017-11-01

    The validity of flux and source term formulae used in shallow water models with porosity for urban flood simulations is assessed by solving the two-dimensional shallow water equations over computational domains representing periodic building layouts. The models under assessment are the Single Porosity (SP), the Integral Porosity (IP) and the Dual Integral Porosity (DIP) models. 9 different geometries are considered. 18 two-dimensional initial value problems and 6 two-dimensional boundary value problems are defined. This results in a set of 96 fine grid simulations. Analysing the simulation results leads to the following conclusions: (i) the DIP flux and source term models outperform those of the SP and IP models when the Riemann problem is aligned with the main street directions, (ii) all models give erroneous flux closures when is the Riemann problem is not aligned with one of the main street directions or when the main street directions are not orthogonal, (iii) the solution of the Riemann problem is self-similar in space-time when the street directions are orthogonal and the Riemann problem is aligned with one of them, (iv) a momentum balance confirms the existence of the transient momentum dissipation model presented in the DIP model, (v) none of the source term models presented so far in the literature allows all flow configurations to be accounted for(vi) future laboratory experiments aiming at the validation of flux and source term closures should focus on the high-resolution, two-dimensional monitoring of both water depth and flow velocity fields.

  12. Fondaparinux in the initial and long-term treatment of venous thromboembolism.

    Science.gov (United States)

    Pesavento, Raffaele; Amitrano, Maria; Trujillo-Santos, Javier; Di Micco, Pierpaolo; Mangiacapra, Sara; López-Jiménez, Luciano; Falgá, Conxita; García-Bragado, Fernando; Piovella, Chiara; Prandoni, Paolo; Monreal, Manuel

    2015-02-01

    Even in the absence of evidence on its long-term efficacy and safety, a number of patients with venous thromboembolism (VTE) receive long-term therapy with fondaparinux alone in everyday practice. We used the Registro Informatizado de Enfermedad Tromboembólica (RIETE) registry to compare the rate of VTE recurrences and major bleeding at 10 and 90 days in patients with and without cancer. For long-term therapy, fondaparinux was compared with vitamin K antagonists (VKA) in patients without cancer and with low-molecular-weight heparin (LMWH) in those with cancer. Of 47,378 patients recruited, 46,513 were initially treated with heparin, 865 with fondaparinux. Then, 263 patients (78 with cancer) were treated for at least 3 months with fondaparinux. After propensity-score matching, there were no differences between patients receiving initial therapy with heparin or fondaparinux. Among patients with cancer, there were no differences between fondaparinux and LMWH. Among patients without cancer, the long-term use of fondaparinux was associated with an increased risk of major bleeding (3.24 % vs. 0.95 %, p<0.05). An unexpected high rate of major bleeding was observed in non-cancer patients treated with long-term fondaparinux. Our small sample does not allow to derive relevant conclusions on the use of fondaparinux in cancer patients. Copyright © 2014 Elsevier Ltd. All rights reserved.

  13. Consideration of emergency source terms for pebble-bed high temperature gas-cooled reactor

    International Nuclear Information System (INIS)

    Tao, Liu; Jun, Zhao; Jiejuan, Tong; Jianzhu, Cao

    2009-01-01

    Being the last barrier in the nuclear power plant defense-in-depth strategy, emergency planning (EP) is an integrated project. One of the key elements in this process is emergency source terms selection. Emergency Source terms for light water reactor (LWR) nuclear power plant (NPP) have been introduced in many technical documents, and advanced NPP emergency planning is attracting attention recently. Commercial practices of advanced NPP are undergoing in the world, pebble-bed high-temperature gas-cooled reactor (HTGR) power plant is under construction in China which is considered as a representative of advanced NPP. The paper tries to find some pieces of suggestion from our investigation. The discussion of advanced NPP EP will be summarized first, and then the characteristics of pebble-bed HTGR relating to EP will be described. Finally, PSA insights on emergency source terms selection and current pebble-bed HTGR emergency source terms suggestions are proposed

  14. Evaluation of the LMFBR cover gas source term and synthesis of the associated R and D

    International Nuclear Information System (INIS)

    Balard, F.; Carluec, B.

    1996-01-01

    At the end of the seventies and the beginning of the eighties, there appeared a pressing need of experimental results to assess the LMFBR's safety level. Because of the urgency, analytical studies were not systematically undertaken and maximum credible cover gas instantaneous source terms (radionuclides core release fraction) were got directly from crude out-of-pile experiment interpretations. Two types of studies and mock-ups were undertaken depending on the timescale of the phenomena: instantaneous source terms (corresponding to an unlikely energetic core disruptive accident CDA), and delayed ones (tens of minutes to some hours). The experiments performed in this frame are reviewed in this presentation: 1) instantaneous source term: - FAUST experiments: I, Cs, UO2 source terms (FzK, Germany), - FAST experiments : pool depth influence on non volatile source term (USA), - CARAVELLE experiments: nonvolatile source term in SPX1 geometry (CEA, France); 2) delayed source term: - NALA experiments: I, Cs, Sr, UO2 source term (FzK, Germany), - PAVE experiments: I source term (CEA, France), - NACOWA experiments: cover gas aerosols enrichment in I and Cs (FzK, Germany) - other French experiments in COPACABANA and GULLIVER facilities. The volatile fission products release is tightly bound to sodium evaporation and a large part of the fission products is dissolved in the liquid sodium aerosols present in the cover gas. Thus the knowledge of the amount of aerosol release to the cover gas is important for the evaluation of the source term. The maximum credible cover gas instantaneous source terms deduced from the experiments have led to conservative source terms to be taken into account in safety analysis. Nevertheless modelling attempts of the observed (in-pile or out-of-pile) physico-chemical phenomena have been undertaken for extrapolation to the reactor case. The main topics of this theoretical research are as follows: fission products evaporation in the cover gas (Fz

  15. Evaluation of the Non-Transient Hydrologic Source Term from the CAMBRIC Underground Nuclear Test in Frenchman Flat, Nevada Test Site

    International Nuclear Information System (INIS)

    Tompson, A B; Maxwell, R M; Carle, S F; Zavarin, M; Pawloski, G A.; Shumaker, D E

    2005-01-01

    Hydrologic Source Term (HST) calculations completed in 1998 at the CAMBRIC underground nuclear test site were LLNL's first attempt to simulate a hydrologic source term at the NTS by linking groundwater flow and transport modeling with geochemical modeling (Tompson et al., 1999). Significant effort was applied to develop a framework that modeled in detail the flow regime and captured all appropriate chemical processes that occurred over time. However, portions of the calculations were simplified because of data limitations and a perceived need for generalization of the results. For example: (1) Transient effects arising from a 16 years of pumping at the site for a radionuclide migration study were not incorporated. (2) Radionuclide fluxes across the water table, as derived from infiltration from a ditch to which pumping effluent was discharged, were not addressed. (3) Hydrothermal effects arising from residual heat of the test were not considered. (4) Background data on the ambient groundwater flow direction were uncertain and not represented. (5) Unclassified information on the Radiologic Source Term (RST) inventory, as tabulated recently by Bowen et al. (2001), was unavailable; instead, only a limited set of derived data were available (see Tompson et al., 1999). (6) Only a small number of radionuclides and geochemical reactions were incorporated in the work. (7) Data and interpretation of the RNM-2S multiple well aquifer test (MWAT) were not available. As a result, the current Transient CAMBRIC Hydrologic Source Term project was initiated as part of a broader Phase 2 Frenchman Flat CAU flow and transport modeling effort. The source term will be calculated under two scenarios: (1) A more specific representation of the transient flow and radionuclide release behavior at the site, reflecting the influence of the background hydraulic gradient, residual test heat, pumping experiment, and ditch recharge, and taking into account improved data sources and modeling

  16. Initial Entry Training: Reducing First Term Attrition Through Effective Organizational Socialization

    National Research Council Canada - National Science Library

    Hayden, Thomas

    2000-01-01

    This paper examines Initial Entry Training (IET) from an organizational behavior perspective to identify if the Army's socialization experience can be enhanced to have a positive impact on first term attrition within the Army...

  17. A nuclear source term analysis for spacecraft power systems

    International Nuclear Information System (INIS)

    McCulloch, W.H.

    1998-01-01

    All US space missions involving on board nuclear material must be approved by the Office of the President. To be approved the mission and the hardware systems must undergo evaluations of the associated nuclear health and safety risk. One part of these evaluations is the characterization of the source terms, i.e., the estimate of the amount, physical form, and location of nuclear material, which might be released into the environment in the event of credible accidents. This paper presents a brief overview of the source term analysis by the Interagency Nuclear Safety Review Panel for the NASA Cassini Space Mission launched in October 1997. Included is a description of the Energy Interaction Model, an innovative approach to the analysis of potential releases from high velocity impacts resulting from launch aborts and reentries

  18. PFLOTRAN-RepoTREND Source Term Comparison Summary.

    Energy Technology Data Exchange (ETDEWEB)

    Frederick, Jennifer M

    2018-03-01

    Code inter-comparison studies are useful exercises to verify and benchmark independently developed software to ensure proper function, especially when the software is used to model high-consequence systems which cannot be physically tested in a fully representative environment. This summary describes the results of the first portion of the code inter-comparison between PFLOTRAN and RepoTREND, which compares the radionuclide source term used in a typical performance assessment.

  19. Fourth order Douglas implicit scheme for solving three dimension reaction diffusion equation with non-linear source term

    Science.gov (United States)

    Hasnain, Shahid; Saqib, Muhammad; Mashat, Daoud Suleiman

    2017-07-01

    This research paper represents a numerical approximation to non-linear three dimension reaction diffusion equation with non-linear source term from population genetics. Since various initial and boundary value problems exist in three dimension reaction diffusion phenomena, which are studied numerically by different numerical methods, here we use finite difference schemes (Alternating Direction Implicit and Fourth Order Douglas Implicit) to approximate the solution. Accuracy is studied in term of L2, L∞ and relative error norms by random selected grids along time levels for comparison with analytical results. The test example demonstrates the accuracy, efficiency and versatility of the proposed schemes. Numerical results showed that Fourth Order Douglas Implicit scheme is very efficient and reliable for solving 3-D non-linear reaction diffusion equation.

  20. Fourth order Douglas implicit scheme for solving three dimension reaction diffusion equation with non-linear source term

    Directory of Open Access Journals (Sweden)

    Shahid Hasnain

    2017-07-01

    Full Text Available This research paper represents a numerical approximation to non-linear three dimension reaction diffusion equation with non-linear source term from population genetics. Since various initial and boundary value problems exist in three dimension reaction diffusion phenomena, which are studied numerically by different numerical methods, here we use finite difference schemes (Alternating Direction Implicit and Fourth Order Douglas Implicit to approximate the solution. Accuracy is studied in term of L2, L∞ and relative error norms by random selected grids along time levels for comparison with analytical results. The test example demonstrates the accuracy, efficiency and versatility of the proposed schemes. Numerical results showed that Fourth Order Douglas Implicit scheme is very efficient and reliable for solving 3-D non-linear reaction diffusion equation.

  1. Low-level waste disposal performance assessments - Total source-term analysis

    Energy Technology Data Exchange (ETDEWEB)

    Wilhite, E.L.

    1995-12-31

    Disposal of low-level radioactive waste at Department of Energy (DOE) facilities is regulated by DOE. DOE Order 5820.2A establishes policies, guidelines, and minimum requirements for managing radioactive waste. Requirements for disposal of low-level waste emplaced after September 1988 include providing reasonable assurance of meeting stated performance objectives by completing a radiological performance assessment. Recently, the Defense Nuclear Facilities Safety Board issued Recommendation 94-2, {open_quotes}Conformance with Safety Standards at Department of Energy Low-Level Nuclear Waste and Disposal Sites.{close_quotes} One of the elements of the recommendation is that low-level waste performance assessments do not include the entire source term because low-level waste emplaced prior to September 1988, as well as other DOE sources of radioactivity in the ground, are excluded. DOE has developed and issued guidance for preliminary assessments of the impact of including the total source term in performance assessments. This paper will present issues resulting from the inclusion of all DOE sources of radioactivity in performance assessments of low-level waste disposal facilities.

  2. PLOTLIB: a computerized nuclear waste source-term library storage and retrieval system

    International Nuclear Information System (INIS)

    Marshall, J.R.; Nowicki, J.A.

    1978-01-01

    The PLOTLIB code was written to provide computer access to the Nuclear Waste Source-Term Library for those users with little previous computer programming experience. The principles of user orientation, quick accessibility, and versatility were extensively employed in the development of the PLOTLIB code to accomplish this goal. The Nuclear Waste Source-Term Library consists of 16 ORIGEN computer runs incorporating a wide variety of differing light water reactor (LWR) fuel cycles and waste streams. The typical isotopic source-term data consist of information on watts, curies, grams, etc., all of which are compiled as a function of time after reactor discharge and unitized on a per metric ton heavy metal basis. The information retrieval code, PLOTLIB, is used to process source-term information requests into computer plots and/or user-specified output tables. This report will serve both as documentation of the current data library and as an operations manual for the PLOTLIB computer code. The accompanying input description, program listing, and sample problems make this code package an easily understood tool for the various nuclear waste studies under way at the Office of Waste Isolation

  3. Regulatory Technology Development Plan - Sodium Fast Reactor: Mechanistic Source Term - Trial Calculation

    International Nuclear Information System (INIS)

    Grabaskas, David

    2016-01-01

    The potential release of radioactive material during a plant incident, referred to as the source term, is a vital design metric and will be a major focus of advanced reactor licensing. The U.S. Nuclear Regulatory Commission has stated an expectation for advanced reactor vendors to present a mechanistic assessment of the potential source term in their license applications. The mechanistic source term presents an opportunity for vendors to realistically assess the radiological consequences of an incident, and may allow reduced emergency planning zones and smaller plant sites. However, the development of a mechanistic source term for advanced reactors is not without challenges, as there are often numerous phenomena impacting the transportation and retention of radionuclides. This project sought to evaluate U.S. capabilities regarding the mechanistic assessment of radionuclide release from core damage incidents at metal fueled, pool-type sodium fast reactors (SFRs). The purpose of the analysis was to identify, and prioritize, any gaps regarding computational tools or data necessary for the modeling of radionuclide transport and retention phenomena. To accomplish this task, a parallel-path analysis approach was utilized. One path, led by Argonne and Sandia National Laboratories, sought to perform a mechanistic source term assessment using available codes, data, and models, with the goal to identify gaps in the current knowledge base. The second path, performed by an independent contractor, performed sensitivity analyses to determine the importance of particular radionuclides and transport phenomena in regards to offsite consequences. The results of the two pathways were combined to prioritize gaps in current capabilities.

  4. Impact of source terms on distances to which reactor accident consequences occur

    International Nuclear Information System (INIS)

    Ostmeyer, R.M.

    1982-01-01

    Estimates of the distances over which reactor accident consequences might occur are important for development of siting criteria and for emergency response planning. This paper summarizes the results of a series of CRAC2 calculations performed to estimate these distances. Because of the current controversy concerning the magnitude of source terms for severe accidents, the impact of source term reductions upon distance estimates is also examined

  5. The long-term problems of contaminated land: Sources, impacts and countermeasures

    International Nuclear Information System (INIS)

    Baes, C.F. III.

    1986-11-01

    This report examines the various sources of radiological land contamination; its extent; its impacts on man, agriculture, and the environment; countermeasures for mitigating exposures; radiological standards; alternatives for achieving land decontamination and cleanup; and possible alternatives for utilizing the land. The major potential sources of extensive long-term land contamination with radionuclides, in order of decreasing extent, are nuclear war, detonation of a single nuclear weapon (e.g., a terrorist act), serious reactor accidents, and nonfission nuclear weapons accidents that disperse the nuclear fuels (termed ''broken arrows'')

  6. Using Reactive Transport Modeling to Evaluate the Source Term at Yucca Mountain

    Energy Technology Data Exchange (ETDEWEB)

    Y. Chen

    2001-12-19

    The conventional approach of source-term evaluation for performance assessment of nuclear waste repositories uses speciation-solubility modeling tools and assumes pure phases of radioelements control their solubility. This assumption may not reflect reality, as most radioelements (except for U) may not form their own pure phases. As a result, solubility limits predicted using the conventional approach are several orders of magnitude higher then the concentrations of radioelements measured in spent fuel dissolution experiments. This paper presents the author's attempt of using a non-conventional approach to evaluate source term of radionuclide release for Yucca Mountain. Based on the general reactive-transport code AREST-CT, a model for spent fuel dissolution and secondary phase precipitation has been constructed. The model accounts for both equilibrium and kinetic reactions. Its predictions have been compared against laboratory experiments and natural analogues. It is found that without calibrations, the simulated results match laboratory and field observations very well in many aspects. More important is the fact that no contradictions between them have been found. This provides confidence in the predictive power of the model. Based on the concept of Np incorporated into uranyl minerals, the model not only predicts a lower Np source-term than that given by conventional Np solubility models, but also produces results which are consistent with laboratory measurements and observations. Moreover, two hypotheses, whether Np enters tertiary uranyl minerals or not, have been tested by comparing model predictions against laboratory observations, the results favor the former. It is concluded that this non-conventional approach of source term evaluation not only eliminates over-conservatism in conventional solubility approach to some extent, but also gives a realistic representation of the system of interest, which is a prerequisite for truly understanding the long-term

  7. Using Reactive Transport Modeling to Evaluate the Source Term at Yucca Mountain

    International Nuclear Information System (INIS)

    Y. Chen

    2001-01-01

    The conventional approach of source-term evaluation for performance assessment of nuclear waste repositories uses speciation-solubility modeling tools and assumes pure phases of radioelements control their solubility. This assumption may not reflect reality, as most radioelements (except for U) may not form their own pure phases. As a result, solubility limits predicted using the conventional approach are several orders of magnitude higher then the concentrations of radioelements measured in spent fuel dissolution experiments. This paper presents the author's attempt of using a non-conventional approach to evaluate source term of radionuclide release for Yucca Mountain. Based on the general reactive-transport code AREST-CT, a model for spent fuel dissolution and secondary phase precipitation has been constructed. The model accounts for both equilibrium and kinetic reactions. Its predictions have been compared against laboratory experiments and natural analogues. It is found that without calibrations, the simulated results match laboratory and field observations very well in many aspects. More important is the fact that no contradictions between them have been found. This provides confidence in the predictive power of the model. Based on the concept of Np incorporated into uranyl minerals, the model not only predicts a lower Np source-term than that given by conventional Np solubility models, but also produces results which are consistent with laboratory measurements and observations. Moreover, two hypotheses, whether Np enters tertiary uranyl minerals or not, have been tested by comparing model predictions against laboratory observations, the results favor the former. It is concluded that this non-conventional approach of source term evaluation not only eliminates over-conservatism in conventional solubility approach to some extent, but also gives a realistic representation of the system of interest, which is a prerequisite for truly understanding the long-term

  8. Source terms; isolation and radiological consequences of carbon-14 waste in the Swedish SFR repository

    International Nuclear Information System (INIS)

    Hesboel, R.; Puigdomenech, I.; Evans, S.

    1990-01-01

    The source term, isolation capacity, and long-term radiological exposure of 14 C from the Swedish underground repository for low and intermediate level waste (SFR) is assessed. The prospective amount of 14 C in the repository is assumed to be 5 TBq. Spent ion exchange resins will be the dominant source of 14 C. The pore water in the concrete repository is expected to maintain a pH of >10.5 for a period of at least 10 6 y. The cement matrix of the repository will retain most of the 14 CO 3 2- initially present. Bacterial production of CO 2 and CH 4 from degradation of ion-exchange resins and bitumen may contribute to 14 C release to the biosphere. However, CH 4 contributes only to a small extent to the overall carbon loss from freshwater ecosystems. The individual doses to local and regional individuals peaked with 5x10 -3 and regional individuals peaked with 5x10 -3 and 8x10 -4 μSv y -1 respectively at about 2.4x10 4 years. A total leakage of 8.4 GBq of 14 C from the repository will cause a total collective dose commitment of 1.1 manSv or 130 manSv TBq -1 . (authors)

  9. The long-term problems of contaminated land: Sources, impacts and countermeasures

    Energy Technology Data Exchange (ETDEWEB)

    Baes, C.F. III

    1986-11-01

    This report examines the various sources of radiological land contamination; its extent; its impacts on man, agriculture, and the environment; countermeasures for mitigating exposures; radiological standards; alternatives for achieving land decontamination and cleanup; and possible alternatives for utilizing the land. The major potential sources of extensive long-term land contamination with radionuclides, in order of decreasing extent, are nuclear war, detonation of a single nuclear weapon (e.g., a terrorist act), serious reactor accidents, and nonfission nuclear weapons accidents that disperse the nuclear fuels (termed ''broken arrows'').

  10. Recent advances in the source term area within the SARNET European severe accident research network

    International Nuclear Information System (INIS)

    Herranz, L.E.; Haste, T.; Kärkelä, T.

    2015-01-01

    Highlights: • Main achievements of source term research in SARNET are given. • Emphasis on the radiologically important iodine and ruthenium fission products. • Conclusions on FP release, transport in the RCS and containment behaviour. • Significance of large-scale integral experiments to validate the analyses used. • A thorough list of the most recent references on source term research results. - Abstract: Source Term has been one of the main research areas addressed within the SARNET network during the 7th EC Framework Programme of EURATOM. The entire source term domain was split into three major areas: oxidising impact on source term, iodine chemistry in the reactor coolant system and containment and data and code assessment. The present paper synthesises the main technical outcome stemming from the SARNET FWP7 project in the area of source term and includes an extensive list of references in which deeper insights on specific issues may be found. Besides, based on the analysis of the current state of the art, an outlook of future source term research is outlined, where major changes in research environment are discussed (i.e., the end of the Phébus FP project; the end of the SARNET projects; and the launch of HORIZON 2020). Most probably research projects will be streamlined towards: release and transport under oxidising conditions, containment chemistry, existing and innovative filtered venting systems and others. These will be in addition to a number of projects that have been completed or are ongoing under different national and international frameworks, like VERDON, CHIP and EPICUR started under the International Source Term Programme (ISTP), the OECD/CSNI programmes BIP, BIP2, STEM, THAI and THAI2, and the French national programme MIRE. The experimental PASSAM project under the 7th EC Framework programme, focused on source term mitigation systems, is highlighted as a good example of a project addressing potential enhancement of safety systems

  11. Recent advances in the source term area within the SARNET European severe accident research network

    Energy Technology Data Exchange (ETDEWEB)

    Herranz, L.E., E-mail: luisen.herranz@ciemat.es [Centro de Investigaciones Energeticas Medio Ambientales y Tecnologica, CIEMAT, Avda. Complutense 40, E-28040 Madrid (Spain); Haste, T. [Institut de Radioprotection et de Sûreté Nucléaire, IRSN, BP 3, F-13115 St Paul lez Durance Cedex (France); Kärkelä, T. [VTT Technical Research Centre of Finland, P.O. Box 1000, FI-02044 VTT Espoo (Finland)

    2015-07-15

    Highlights: • Main achievements of source term research in SARNET are given. • Emphasis on the radiologically important iodine and ruthenium fission products. • Conclusions on FP release, transport in the RCS and containment behaviour. • Significance of large-scale integral experiments to validate the analyses used. • A thorough list of the most recent references on source term research results. - Abstract: Source Term has been one of the main research areas addressed within the SARNET network during the 7th EC Framework Programme of EURATOM. The entire source term domain was split into three major areas: oxidising impact on source term, iodine chemistry in the reactor coolant system and containment and data and code assessment. The present paper synthesises the main technical outcome stemming from the SARNET FWP7 project in the area of source term and includes an extensive list of references in which deeper insights on specific issues may be found. Besides, based on the analysis of the current state of the art, an outlook of future source term research is outlined, where major changes in research environment are discussed (i.e., the end of the Phébus FP project; the end of the SARNET projects; and the launch of HORIZON 2020). Most probably research projects will be streamlined towards: release and transport under oxidising conditions, containment chemistry, existing and innovative filtered venting systems and others. These will be in addition to a number of projects that have been completed or are ongoing under different national and international frameworks, like VERDON, CHIP and EPICUR started under the International Source Term Programme (ISTP), the OECD/CSNI programmes BIP, BIP2, STEM, THAI and THAI2, and the French national programme MIRE. The experimental PASSAM project under the 7th EC Framework programme, focused on source term mitigation systems, is highlighted as a good example of a project addressing potential enhancement of safety systems

  12. Estimation of Source terms for Emergency Planning and Preparedness

    Energy Technology Data Exchange (ETDEWEB)

    Yi, Chul Un; Chung, Bag Soon; Ahn, Jae Hyun; Yoon, Duk Ho; Jeong, Chul Young; Lim, Jong Dae [Korea Electric Power Research Institute, Taejon (Korea, Republic of); Kang, Sun Gu; Suk, Ho; Park, Sung Kyu; Lim, Hac Kyu; Lee, Kwang Nam [Korea Power Engineering Company Consulting and Architecture Engineers, (Korea, Republic of)

    1997-12-31

    In this study the severe accident sequences for each plant of concern, which represent accident sequences with a high core damage frequency and significant accident consequences, were selected based on the results of probabilistic safety assessments and source term and time-histories of various safety parameters under severe accidents. Accidents progression analysis for each selected accident sequence was performed by MAAP code. It was determined that the measured values, dose rate and radioisotope concentration, could provide information to the operators on occurrence and timing of core damage, reactor vessel failure, and containment failure during severe accidents. Radioactive concentration in the containment atmosphere, which may be measured by PASS, was estimated. Radioisotope concentration in emergency planning, evaluation of source term behavior in the containment, estimation of core damage degree, analysis of severe accident phenomena, core damage timing, and the amount of radioisotope released to the environment. (author). 50 refs., 60 figs.

  13. Added Value of uncertainty Estimates of SOurce term and Meteorology (AVESOME)

    DEFF Research Database (Denmark)

    Sørensen, Jens Havskov; Schönfeldt, Fredrik; Sigg, Robert

    In the early phase of a nuclear accident, two large sources of uncertainty exist: one related to the source term and one associated with the meteorological data. Operational methods are being developed in AVESOME for quantitative estimation of uncertainties in atmospheric dispersion prediction.......g. at national meteorological services, the proposed methodology is feasible for real-time use, thereby adding value to decision support. In the recent NKS-B projects MUD, FAUNA and MESO, the implications of meteorological uncertainties for nuclear emergency preparedness and management have been studied...... uncertainty in atmospheric dispersion model forecasting stemming from both the source term and the meteorological data is examined. Ways to implement the uncertainties of forecasting in DSSs, and the impacts on real-time emergency management are described. The proposed methodology allows for efficient real...

  14. The Source Inversion Validation (SIV) Initiative: A Collaborative Study on Uncertainty Quantification in Earthquake Source Inversions

    Science.gov (United States)

    Mai, P. M.; Schorlemmer, D.; Page, M.

    2012-04-01

    Earthquake source inversions image the spatio-temporal rupture evolution on one or more fault planes using seismic and/or geodetic data. Such studies are critically important for earthquake seismology in general, and for advancing seismic hazard analysis in particular, as they reveal earthquake source complexity and help (i) to investigate earthquake mechanics; (ii) to develop spontaneous dynamic rupture models; (iii) to build models for generating rupture realizations for ground-motion simulations. In applications (i - iii), the underlying finite-fault source models are regarded as "data" (input information), but their uncertainties are essentially unknown. After all, source models are obtained from solving an inherently ill-posed inverse problem to which many a priori assumptions and uncertain observations are applied. The Source Inversion Validation (SIV) project is a collaborative effort to better understand the variability between rupture models for a single earthquake (as manifested in the finite-source rupture model database) and to develop robust uncertainty quantification for earthquake source inversions. The SIV project highlights the need to develop a long-standing and rigorous testing platform to examine the current state-of-the-art in earthquake source inversion, and to develop and test novel source inversion approaches. We will review the current status of the SIV project, and report the findings and conclusions of the recent workshops. We will briefly discuss several source-inversion methods, how they treat uncertainties in data, and assess the posterior model uncertainty. Case studies include initial forward-modeling tests on Green's function calculations, and inversion results for synthetic data from spontaneous dynamic crack-like strike-slip earthquake on steeply dipping fault, embedded in a layered crustal velocity-density structure.

  15. Design parameters and source terms: Volume 1, Design parameters: Revision 0

    International Nuclear Information System (INIS)

    1987-10-01

    The Design Parameters and Source Terms Document was prepared in accordance with DOE request and to provide data for the environmental impact study to be performed in the future for the Deaf Smith County, Texas site for a nuclear waste repository in salt. This document updates a previous unpublished report by Stearns Catalytic Corporation (SCC), entitled ''Design Parameters and Source Terms for a Two-Phase Repository in Salt,'' 1985, to the level of the Site Characterization Plan - Conceptual Design Report. The previous unpublished SCC Study identifies the data needs for the Environmental Assessment effort for seven possible Salt Repository sites

  16. Technological plasma source equipped with combined system of vacuum-arc discharge initiation

    International Nuclear Information System (INIS)

    Sysoev, Yu.O.

    2013-01-01

    The construction and the operation principle of erosion plasma source with a three-stage system of vacuum-arc discharge excitation is described. As first two step was used the modified contactless start system with plasma injector, which was widely used in standard plasma sources of the ''Bulat'' systems. The operation principle of the third stage was based on the transition of glow discharge to arc discharge. Coordinated operation of three stages during various stages of coating deposition provided significant increasing of service life and reliability of the system of vacuum-arc discharge initiation and extended the functionality of the plasma source

  17. Coarse Grid Modeling of Turbine Film Cooling Flows Using Volumetric Source Terms

    Science.gov (United States)

    Heidmann, James D.; Hunter, Scott D.

    2001-01-01

    The recent trend in numerical modeling of turbine film cooling flows has been toward higher fidelity grids and more complex geometries. This trend has been enabled by the rapid increase in computing power available to researchers. However, the turbine design community requires fast turnaround time in its design computations, rendering these comprehensive simulations ineffective in the design cycle. The present study describes a methodology for implementing a volumetric source term distribution in a coarse grid calculation that can model the small-scale and three-dimensional effects present in turbine film cooling flows. This model could be implemented in turbine design codes or in multistage turbomachinery codes such as APNASA, where the computational grid size may be larger than the film hole size. Detailed computations of a single row of 35 deg round holes on a flat plate have been obtained for blowing ratios of 0.5, 0.8, and 1.0, and density ratios of 1.0 and 2.0 using a multiblock grid system to resolve the flows on both sides of the plate as well as inside the hole itself. These detailed flow fields were spatially averaged to generate a field of volumetric source terms for each conservative flow variable. Solutions were also obtained using three coarse grids having streamwise and spanwise grid spacings of 3d, 1d, and d/3. These coarse grid solutions used the integrated hole exit mass, momentum, energy, and turbulence quantities from the detailed solutions as volumetric source terms. It is shown that a uniform source term addition over a distance from the wall on the order of the hole diameter is able to predict adiabatic film effectiveness better than a near-wall source term model, while strictly enforcing correct values of integrated boundary layer quantities.

  18. Are humans the initial source of canine mange?

    Science.gov (United States)

    Andriantsoanirina, Valérie; Fang, Fang; Ariey, Frédéric; Izri, Arezki; Foulet, Françoise; Botterel, Françoise; Bernigaud, Charlotte; Chosidow, Olivier; Huang, Weiyi; Guillot, Jacques; Durand, Rémy

    2016-03-25

    Scabies, or mange as it is called in animals, is an ectoparasitic contagious infestation caused by the mite Sarcoptes scabiei. Sarcoptic mange is an important veterinary disease leading to significant morbidity and mortality in wild and domestic animals. A widely accepted hypothesis, though never substantiated by factual data, suggests that humans were the initial source of the animal contamination. In this study we performed phylogenetic analyses of populations of S. scabiei from humans and from canids to validate or not the hypothesis of a human origin of the mites infecting domestic dogs. Mites from dogs and foxes were obtained from three French sites and from other countries. A part of cytochrome c oxidase subunit 1 (cox1) gene was amplified and directly sequenced. Other sequences corresponding to mites from humans, raccoon dogs, foxes, jackal and dogs from various geographical areas were retrieved from GenBank. Phylogenetic analyses were performed using the Otodectes cynotis cox1 sequence as outgroup. Maximum Likelihood and Bayesian Inference analysis approaches were used. To visualize the relationship between the haplotypes, a median joining haplotype network was constructed using Network v4.6 according to host. Twenty-one haplotypes were observed among mites collected from five different host species, including humans and canids from nine geographical areas. The phylogenetic trees based on Maximum Likelihood and Bayesian Inference analyses showed similar topologies with few differences in node support values. The results were not consistent with a human origin of S. scabiei mites in dogs and, on the contrary, did not exclude the opposite hypothesis of a host switch from dogs to humans. Phylogenetic relatedness may have an impact in terms of epidemiological control strategy. Our results and other recent studies suggest to re-evaluate the level of transmission between domestic dogs and humans.

  19. Estimating the Benefits of the Air Force Purchasing and Supply Chain Management Initiative

    Science.gov (United States)

    2008-01-01

    sector, known as strategic sourcing.6 The Customer Relationship Management initiative ( CRM ) pro- vides a single customer point of contact for all... Customer Relationship Management initiative. commodity council A term used to describe a cross-functional sourc- ing group charged with formulating a...initiative has four major components, all based on commercial best practices (Gabreski, 2004): commodity councils customer relationship management

  20. NRC source term assessment for incident response dose projections

    International Nuclear Information System (INIS)

    Easley, P.; Pasedag, W.

    1984-01-01

    The NRC provides advice and assistance to licensees and State and local authorities in responding to accidents. The TACT code supports this function by providing source term projections for two situations during early (15 to 60 minutes) accident response: (1) Core/containment damage is indicated, but there are no measured releases. Quantification of a predicted release permits emergency response before people are exposed. With TACT, response personnel can estimate releases based on fuel and cladding conditions, coolant boundary and containment integrity, and mitigative systems operability. For this type of estimate, TACT is intermediate between default assumptions and time-consuming mechanistic codes. (2) A combination of plant status and limited release data are available. For this situation, iterations between predictions based on known conditions which are compared to measured releases gives reasonable confidence in supplemental source term information otherwise unavailable: nuclide mix, releases not monitored, and trending or abrupt changes. The assumptions and models used in TACT, and examples of its use, are given in this paper

  1. Finding Funding: A Guide to Federal Sources for Asset-Building Initiatives. Finding Funding Series

    Science.gov (United States)

    Lind, Christianne; Relave, Nanette; Schmid, William; Terzaghi, Damon

    2009-01-01

    This guide outlines strategies for financing asset-building initiatives and provides information on 71 federal funding sources that can be used to support a range of activities and services. It includes well-known sources of funding for asset building, for example, the Assets for Independence Demonstration Program and the Family Self-Sufficiency…

  2. Selected source term topics. Report to CSNI by an OECD/NEA Group of experts

    International Nuclear Information System (INIS)

    1987-04-01

    CSNI Report 136 summarizes the results of the work performed by the Group of Experts on the Source Term and Environmental Consequences (PWG4) during the period extending from 1983 and 1986. This report is complementary to Part 1, 'Technical Status of the Source Term' of CSNI Report 135, 'Report to CSNI on Source Term Assessment, Containment atmosphere control systems, and accident consequences'; it considers in detail a number of very specific issues thought to be important in the source term area. It consists of: an executive summary (prepared by the Chairman of the Group), a section on conclusions and recommendations, and five technical chapters (fission product chemistry in the primary circuit of a LWR during severe accidents; resuspension/re-entrainment of aerosols in LWRs following a meltdown accident; iodine chemistry under severe accident conditions; effects of combustion, steam explosions and pressurized melt ejection on fission product behaviour; radionuclide removal by pool scrubbing), a technical annex and two appendices

  3. Development of the methodology for application of revised source term to operating nuclear power plants in Korea

    International Nuclear Information System (INIS)

    Kang, M.S.; Kang, P.; Kang, C.S.; Moon, J.H.

    2004-01-01

    Considering the current trend in applying the revised source term proposed by NUREG-1465 to the nuclear power plants in the U.S., it is expected that the revised source term will be applied to the Korean operating nuclear power plants in the near future, even though the exact time can not be estimated. To meet the future technical demands, it is necessary to prepare the technical system including the related regulatory requirements in advance. In this research, therefore, it is intended to develop the methodology to apply the revised source term to operating nuclear power plants in Korea. Several principles were established to develop the application methodologies. First, it is not necessary to modify the existing regulations about source term (i.e., any back-fitting to operating nuclear plants is not necessary). Second, if the pertinent margin of safety is guaranteed, the revised source term suggested by NUREG-1465 may be useful to full application. Finally, a part of revised source term could be selected to application based on the technical feasibility. As the results of this research, several methodologies to apply the revised source term to the Korean operating nuclear power plants have been developed, which include: 1) the selective (or limited) application to use only some of all the characteristics of the revised source term, such as release timing of fission products and chemical form of radio-iodine and 2) the full application to use all the characteristics of the revised source term. The developed methodologies are actually applied to Ulchin 9 and 4 units and their application feasibilities are reviewed. The results of this research are used as either a manual in establishing the plan and the procedure for applying the revised source term to the domestic nuclear plant from the utility's viewpoint; or a technical basis of revising the related regulations from the regulatory body's viewpoint. The application of revised source term to operating nuclear

  4. Regulatory Technology Development Plan - Sodium Fast Reactor: Mechanistic Source Term – Trial Calculation

    Energy Technology Data Exchange (ETDEWEB)

    Grabaskas, David [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Bucknor, Matthew [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Jerden, James [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Brunett, Acacia J. [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Denman, Matthew [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Nuclear Engineering Division; Clark, Andrew [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Nuclear Engineering Division; Denning, Richard S. [Consultant, Columbus, OH (United States)

    2016-10-01

    The potential release of radioactive material during a plant incident, referred to as the source term, is a vital design metric and will be a major focus of advanced reactor licensing. The U.S. Nuclear Regulatory Commission has stated an expectation for advanced reactor vendors to present a mechanistic assessment of the potential source term in their license applications. The mechanistic source term presents an opportunity for vendors to realistically assess the radiological consequences of an incident, and may allow reduced emergency planning zones and smaller plant sites. However, the development of a mechanistic source term for advanced reactors is not without challenges, as there are often numerous phenomena impacting the transportation and retention of radionuclides. This project sought to evaluate U.S. capabilities regarding the mechanistic assessment of radionuclide release from core damage incidents at metal fueled, pool-type sodium fast reactors (SFRs). The purpose of the analysis was to identify, and prioritize, any gaps regarding computational tools or data necessary for the modeling of radionuclide transport and retention phenomena. To accomplish this task, a parallel-path analysis approach was utilized. One path, led by Argonne and Sandia National Laboratories, sought to perform a mechanistic source term assessment using available codes, data, and models, with the goal to identify gaps in the current knowledge base. The second path, performed by an independent contractor, performed sensitivity analyses to determine the importance of particular radionuclides and transport phenomena in regards to offsite consequences. The results of the two pathways were combined to prioritize gaps in current capabilities.

  5. Source-term model for the SYVAC3-NSURE performance assessment code

    International Nuclear Information System (INIS)

    Rowat, J.H.; Rattan, D.S.; Dolinar, G.M.

    1996-11-01

    Radionuclide contaminants in wastes emplaced in disposal facilities will not remain in those facilities indefinitely. Engineered barriers will eventually degrade, allowing radioactivity to escape from the vault. The radionuclide release rate from a low-level radioactive waste (LLRW) disposal facility, the source term, is a key component in the performance assessment of the disposal system. This report describes the source-term model that has been implemented in Ver. 1.03 of the SYVAC3-NSURE (Systems Variability Analysis Code generation 3-Near Surface Repository) code. NSURE is a performance assessment code that evaluates the impact of near-surface disposal of LLRW through the groundwater pathway. The source-term model described here was developed for the Intrusion Resistant Underground Structure (IRUS) disposal facility, which is a vault that is to be located in the unsaturated overburden at AECL's Chalk River Laboratories. The processes included in the vault model are roof and waste package performance, and diffusion, advection and sorption of radionuclides in the vault backfill. The model presented here was developed for the IRUS vault; however, it is applicable to other near-surface disposal facilities. (author). 40 refs., 6 figs

  6. Considerations about source term now used aiming to emergency planning

    International Nuclear Information System (INIS)

    Austregesilo Filho, H.

    1987-01-01

    The applicability of source terms, in parametric studies for improving external emergengy plan for Angra-I reactor is presented. The source term is defined as, the quantity and radioactive material disposable for releasing to the environment in case of austere accident in a nuclear power plant. The following hypothesis: occuring accident, 100% of the noble gases, 50% of halogens and 1% of solid fission products contained into the reactor core, are released immediately toward the containment building; the radioactivity releasing to the environment is done at a constant rate of 0.1% in mass per day; the actuation of mitigated systems of radioactivity releasing, such as, spray of container or system of air recirculation by filters, is not considered; and the releasing is done at soil level. (M.C.K.) [pt

  7. A note on variational multiscale methods for high-contrast heterogeneous porous media flows with rough source terms

    KAUST Repository

    Calo, Victor M.

    2011-09-01

    In this short note, we discuss variational multiscale methods for solving porous media flows in high-contrast heterogeneous media with rough source terms. Our objective is to separate, as much as possible, subgrid effects induced by the media properties from those due to heterogeneous source terms. For this reason, enriched coarse spaces designed for high-contrast multiscale problems are used to represent the effects of heterogeneities of the media. Furthermore, rough source terms are captured via auxiliary correction equations that appear in the formulation of variational multiscale methods [23]. These auxiliary equations are localized and one can use additive or multiplicative constructions for the subgrid corrections as discussed in the current paper. Our preliminary numerical results show that one can capture the effects due to both spatial heterogeneities in the coefficients (such as permeability field) and source terms (e.g., due to singular well terms) in one iteration. We test the cases for both smooth source terms and rough source terms and show that with the multiplicative correction, the numerical approximations are more accurate compared to the additive correction. © 2010 Elsevier Ltd.

  8. Centrifugal Filtration System for Severe Accident Source Term Treatment

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Shu Chang; Yim, Man Sung [KAIST, Daejeon (Korea, Republic of)

    2016-05-15

    The objective of this paper is to present the conceptual design of a filtration system that can be used to process airborne severe accident source term. Reactor containment may lose its structural integrity due to over-pressurization during a severe accident. This can lead to uncontrolled radioactive releases to the environment. For preventing the dispersion of these uncontrolled radioactive releases to the environment, several ways to capture or mitigate these radioactive source term releases are under investigation at KAIST. Such technologies are based on concepts like a vortex-like air curtain, a chemical spray, and a suction arm. Treatment of the radioactive material captured by these systems would be required, before releasing to environment. For current filtration systems in the nuclear industry, IAEA lists sand, multi-venturi scrubber, high efficiency particulate arresting (HEPA), charcoal and combinations of the above in NS-G-1-10, 4.143. Most if not all of the requirements of the scenario for applying this technology near the containment of an NPP site and the environmental constraints were analyzed for use in the design of the centrifuge filtration system.

  9. Cost Analysis of a High Support Housing Initiative for Persons with Severe Mental Illness and Long-Term Psychiatric Hospitalization.

    Science.gov (United States)

    Rudoler, David; de Oliveira, Claire; Jacob, Binu; Hopkins, Melonie; Kurdyak, Paul

    2018-01-01

    The objective of this article was to conduct a cost analysis comparing the costs of a supportive housing intervention to inpatient care for clients with severe mental illness who were designated alternative-level care while inpatient at the Centre for Addiction and Mental Health in Toronto. The intervention, called the High Support Housing Initiative, was implemented in 2013 through a collaboration between 15 agencies in the Toronto area. The perspective of this cost analysis was that of the Ontario Ministry of Health and Long-Term Care. We compared the cost of inpatient mental health care to high-support housing. Cost data were derived from a variety of sources, including health administrative data, expenditures reported by housing providers, and document analysis. The High Support Housing Initiative was cost saving relative to inpatient care. The average cost savings per diem were between $140 and $160. This amounts to an annual cost savings of approximately $51,000 to $58,000. When tested through sensitivity analysis, the intervention remained cost saving in most scenarios; however, the result was highly sensitive to health system costs for clients of the High Support Housing Initiative program. This study suggests the High Support Housing Initiative is potentially cost saving relative to inpatient hospitalization at the Centre for Addiction and Mental Health.

  10. Realistic minimum accident source terms - Evaluation, application, and risk acceptance

    International Nuclear Information System (INIS)

    Angelo, P. L.

    2009-01-01

    The evaluation, application, and risk acceptance for realistic minimum accident source terms can represent a complex and arduous undertaking. This effort poses a very high impact to design, construction cost, operations and maintenance, and integrated safety over the expected facility lifetime. At the 2005 Nuclear Criticality Safety Division (NCSD) Meeting in Knoxville Tenn., two papers were presented mat summarized the Y-12 effort that reduced the number of criticality accident alarm system (CAAS) detectors originally designed for the new Highly Enriched Uranium Materials Facility (HEUMF) from 258 to an eventual as-built number of 60. Part of that effort relied on determining a realistic minimum accident source term specific to the facility. Since that time, the rationale for an alternate minimum accident has been strengthened by an evaluation process that incorporates realism. A recent update to the HEUMF CAAS technical basis highlights the concepts presented here. (authors)

  11. Lessons Learned from Characterization, Performance Assessment, and EPA Regulatory Review of the 1996 Actinide Source Term for the Waste Isolation Pilot Plant

    International Nuclear Information System (INIS)

    Larson, K.W.; Moore, R.C.; Nowak, E.J.; Papenguth, H.W.; Jow, H.

    1999-01-01

    The Waste Isolation Pilot Plant (WIPP) is a US Department of Energy (DOE) facility for the permanent disposal of transuranic waste from defense activities. In 1996, the DOE submitted the Title 40 CFR Part 191 Compliance Certification Application for the Waste Isolation Pilot Plant (CCA) to the US Environmental Protection Agency (EPA). The CCA included a probabilistic performance assessment (PA) conducted by Sandia National Laboratories to establish compliance with the quantitative release limits defined in 40 CFR 191.13. An experimental program to collect data relevant to the actinide source term began around 1989, which eventually supported the 1996 CCA PA actinide source term model. The actinide source term provided an estimate of mobile dissolved and colloidal Pu, Am, U, Th, and Np concentrations in their stable oxidation states, and accounted for effects of uncertainty in the chemistry of brines in waste disposal areas. The experimental program and the actinide source term included in the CCA PA underwent EPA review lasting more than 1 year. Experiments were initially conducted to develop data relevant to the wide range of potential future conditions in waste disposal areas. Interim, preliminary performance assessments and actinide source term models provided insight allowing refinement of experiments and models. Expert peer review provided additional feedback and confidence in the evolving experimental program. By 1995, the chemical database and PA predictions of WIPP performance were considered reliable enough to support the decision to add an MgO backfill to waste rooms to control chemical conditions and reduce uncertainty in actinide concentrations, especially for Pu and Am. Important lessons learned through the characterization, PA modeling, and regulatory review of the actinide source term are (1) experimental characterization and PA should evolve together, with neither activity completely dominating the other, (2) the understanding of physical processes

  12. Long-term outcome of patients with macroprolactinomas initially treated with dopamine agonists

    NARCIS (Netherlands)

    Kars, Marleen; Pereira, Alberto M.; Smit, Johannes W.; Romijn, Johannes A.

    2009-01-01

    Dopamine agonists are the first line therapy for the treatment of prolactinomas. The aim of this study was to assess the outcome of macroprolactinomas during long-term follow-up after initial treatment with dopamine agonists. Retrospective follow-up study. We included 72 consecutive patients (age

  13. A novel integrated approach for the hazardous radioactive dust source terms estimation in future nuclear fusion power plants.

    Science.gov (United States)

    Poggi, L A; Malizia, A; Ciparisse, J F; Gaudio, P

    2016-10-01

    An open issue still under investigation by several international entities working on the safety and security field for the foreseen nuclear fusion reactors is the estimation of source terms that are a hazard for the operators and public, and for the machine itself in terms of efficiency and integrity in case of severe accident scenarios. Source term estimation is a crucial key safety issue to be addressed in the future reactors safety assessments, and the estimates available at the time are not sufficiently satisfactory. The lack of neutronic data along with the insufficiently accurate methodologies used until now, calls for an integrated methodology for source term estimation that can provide predictions with an adequate accuracy. This work proposes a complete methodology to estimate dust source terms starting from a broad information gathering. The wide number of parameters that can influence dust source term production is reduced with statistical tools using a combination of screening, sensitivity analysis, and uncertainty analysis. Finally, a preliminary and simplified methodology for dust source term production prediction for future devices is presented.

  14. Chernobyl source term, atmospheric dispersion, and dose estimation

    International Nuclear Information System (INIS)

    Gudiksen, P.H.; Harvey, T.F.; Lange, R.

    1988-02-01

    The Chernobyl source term available for long-range transport was estimated by integration of radiological measurements with atmospheric dispersion modeling, and by reactor core radionuclide inventory estimation in conjunction with WASH-1400 release fractions associated with specific chemical groups. These analyses indicated that essentially all of the noble gases, 80% of the radioiodines, 40% of the radiocesium, 10% of the tellurium, and about 1% or less of the more refractory elements were released. Atmospheric dispersion modeling of the radioactive cloud over the Northern Hemisphere revealed that the cloud became segmented during the first day, with the lower section heading toward Scandinavia and the uppper part heading in a southeasterly direction with subsequent transport across Asia to Japan, the North Pacific, and the west coast of North America. The inhalation doses due to direct cloud exposure were estimated to exceed 10 mGy near the Chernobyl area, to range between 0.1 and 0.001 mGy within most of Europe, and to be generally less than 0.00001 mGy within the US. The Chernobyl source term was several orders of magnitude greater than those associated with the Windscale and TMI reactor accidents, while the 137 Cs from the Chernobyl event is about 6% of that released by the US and USSR atmospheric nuclear weapon tests. 9 refs., 3 figs., 6 tabs

  15. Source term identification in atmospheric modelling via sparse optimization

    Science.gov (United States)

    Adam, Lukas; Branda, Martin; Hamburger, Thomas

    2015-04-01

    Inverse modelling plays an important role in identifying the amount of harmful substances released into atmosphere during major incidents such as power plant accidents or volcano eruptions. Another possible application of inverse modelling lies in the monitoring the CO2 emission limits where only observations at certain places are available and the task is to estimate the total releases at given locations. This gives rise to minimizing the discrepancy between the observations and the model predictions. There are two standard ways of solving such problems. In the first one, this discrepancy is regularized by adding additional terms. Such terms may include Tikhonov regularization, distance from a priori information or a smoothing term. The resulting, usually quadratic, problem is then solved via standard optimization solvers. The second approach assumes that the error term has a (normal) distribution and makes use of Bayesian modelling to identify the source term. Instead of following the above-mentioned approaches, we utilize techniques from the field of compressive sensing. Such techniques look for a sparsest solution (solution with the smallest number of nonzeros) of a linear system, where a maximal allowed error term may be added to this system. Even though this field is a developed one with many possible solution techniques, most of them do not consider even the simplest constraints which are naturally present in atmospheric modelling. One of such examples is the nonnegativity of release amounts. We believe that the concept of a sparse solution is natural in both problems of identification of the source location and of the time process of the source release. In the first case, it is usually assumed that there are only few release points and the task is to find them. In the second case, the time window is usually much longer than the duration of the actual release. In both cases, the optimal solution should contain a large amount of zeros, giving rise to the

  16. Fission product source terms and engineered safety features

    International Nuclear Information System (INIS)

    Malinauskas, A.P.

    1984-01-01

    The author states that new, technically defensible, methodologies to establish realistic source term values for nuclear reactor accidents will soon be available. Although these methodologies will undoubtedly find widespread use in the development of accident response procedures, the author states that it is less clear that the industry is preparing to employ the newer results to develop a more rational approach to strategies for the mitigation of fission product releases. Questions concerning the performance of existing engineered safety systems are reviewed

  17. A simplified approach to estimating reference source terms for LWR designs

    International Nuclear Information System (INIS)

    1999-12-01

    systems. The publication of this IAEA technical document represents the conclusion of a task, initiated in 1996, devoted to the estimation of the radioactive source term in nuclear reactors. It focuses mainly on light water reactors (LWRs)

  18. Use of source term code package in the ELEBRA MX-850 system

    International Nuclear Information System (INIS)

    Guimaraes, A.C.F.; Goes, A.G.A.

    1988-12-01

    The implantation of source term code package in the ELEBRA-MX850 system is presented. The source term is formed when radioactive materials generated in nuclear fuel leakage toward containment and the external environment to reactor containment. The implantated version in the ELEBRA system are composed of five codes: MARCH 3, TRAPMELT 3, THCCA, VANESA and NAVA. The original example case was used. The example consists of a small loca accident in a PWR type reactor. A sensitivity study for the TRAPMELT 3 code was carried out, modifying the 'TIME STEP' to estimate the processing time of CPU for executing the original example case. (M.C.K.) [pt

  19. A simple method for estimating potential source term bypass fractions from confinement structures

    International Nuclear Information System (INIS)

    Kalinich, D.A.; Paddleford, D.F.

    1997-01-01

    Confinement structures house many of the operating processes at the Savannah River Site (SRS). Under normal operating conditions, a confinement structure in conjunction with its associated ventilation systems prevents the release of radiological material to the environment. However, under potential accident conditions, the performance of the ventilation systems and integrity of the structure may be challenged. In order to calculate the radiological consequences associated with a potential accident (e.g. fires, explosion, spills, etc.), it is necessary to determine the fraction of the source term initially generated by the accident that escapes from the confinement structure to the environment. While it would be desirable to estimate the potential bypass fraction using sophisticated control-volume/flow path computer codes (e.g. CONTAIN, MELCOR, etc.) in order to take as much credit as possible for the mitigative effects of the confinement structure, there are many instances where using such codes is not tractable due to limits on the level-of-effort allotted to perform the analysis. Moreover, the current review environment, with its emphasis on deterministic/bounding-versus probabilistic/best-estimate-analysis discourages using analytical techniques that require the consideration of a large number of parameters. Discussed herein is a simplified control-volume/flow path approach for calculating source term bypass fraction that is amenable to solution in a spreadsheet or with a commercial mathematical solver (e.g. MathCad or Mathematica). It considers the effects of wind and fire pressure gradients on the structure, ventilation system operation, and Halon discharges. Simple models are used to characterize the engineered and non-engineered flow paths. By making judicious choices for the limited set of problem parameters, the results from this approach can be defended as bounding and conservative

  20. Development of Reference Source Terms for EU-APR1400

    Energy Technology Data Exchange (ETDEWEB)

    Kim, ByungIl; Lee, Chonghui; Lee, Dongsu; Ko, Heejin; Kang, Sangho [KEPCO Engineering and Construction Co. Inc., Yongin (Korea, Republic of)

    2014-05-15

    These source terms are developed for the typical U. S. NPP and do not reflect the design characteristics of EU-APR1400 (1,400 MWe PWR) which will be applied for the EUR certification in European countries. The process of developing the RST for EU-APR1400 is to undergo a similar process that NUREG-1465 had gone through when it came out with its proposed source terms. The purpose of this study is to develop the EU-APR1400 design-specific RST complied with the EUR. The Large LOCA is the reference equence used in the NUREG-1465 evaluation, whereas the EUAPR1400 risk-significant sequences are dominated by small LOCA and non-LOCA sequences. Moreover, when considering the EU-APR1400 has many design features to mitigate the consequences of severe accident phenomena, it is not surprising that the aspects of both release fractions and durations are distinctly different from NUREG-1465. This RST will be continuously updated to reflect to the design features of EU-APR1400, and then, be used as the reference for design purposes such as criteria satisfaction of radioactivity releases, equipment survivability, control room habitability for severe accident, and so on.

  1. Semi-implicit and fully implicit shock-capturing methods for hyperbolic conservation laws with stiff source terms

    International Nuclear Information System (INIS)

    Yee, H.C.; Shinn, J.L.

    1986-12-01

    Some numerical aspects of finite-difference algorithms for nonlinear multidimensional hyperbolic conservation laws with stiff nonhomogenous (source) terms are discussed. If the stiffness is entirely dominated by the source term, a semi-implicit shock-capturing method is proposed provided that the Jacobian of the source terms possesses certain properties. The proposed semi-implicit method can be viewed as a variant of the Bussing and Murman point-implicit scheme with a more appropriate numerical dissipation for the computation of strong shock waves. However, if the stiffness is not solely dominated by the source terms, a fully implicit method would be a better choice. The situation is complicated by problems that are higher than one dimension, and the presence of stiff source terms further complicates the solution procedures for alternating direction implicit (ADI) methods. Several alternatives are discussed. The primary motivation for constructing these schemes was to address thermally and chemically nonequilibrium flows in the hypersonic regime. Due to the unique structure of the eigenvalues and eigenvectors for fluid flows of this type, the computation can be simplified, thus providing a more efficient solution procedure than one might have anticipated

  2. Semi-implicit and fully implicit shock-capturing methods for hyperbolic conservation laws with stiff source terms

    International Nuclear Information System (INIS)

    Yee, H.C.; Shinn, J.L.

    1987-01-01

    Some numerical aspects of finite-difference algorithms for nonlinear multidimensional hyperbolic conservation laws with stiff nonhomogeneous (source) terms are discussed. If the stiffness is entirely dominated by the source term, a semi-implicit shock-capturing method is proposed provided that the Jacobian of the source terms possesses certain properties. The proposed semi-implicit method can be viewed as a variant of the Bussing and Murman point-implicit scheme with a more appropriate numerical dissipation for the computation of strong shock waves. However, if the stiffness is not solely dominated by the source terms, a fully implicit method would be a better choice. The situation is complicated by problems that are higher than one dimension, and the presence of stiff source terms further complicates the solution procedures for alternating direction implicit (ADI) methods. Several alternatives are discussed. The primary motivation for constructing these schemes was to address thermally and chemically nonequilibrium flows in the hypersonic regime. Due to the unique structure of the eigenvalues and eigenvectors for fluid flows of this type, the computation can be simplified, thus providing a more efficient solution procedure than one might have anticipated. 46 references

  3. Evaluation of Long-term Performance of Enhanced Anaerobic Source Zone Bioremediation using mass flux

    Science.gov (United States)

    Haluska, A.; Cho, J.; Hatzinger, P.; Annable, M. D.

    2017-12-01

    Chlorinated ethene DNAPL source zones in groundwater act as potential long term sources of contamination as they dissolve yielding concentrations well above MCLs, posing an on-going public health risk. Enhanced bioremediation has been applied to treat many source zones with significant promise, but long-term sustainability of this technology has not been thoroughly assessed. This study evaluated the long-term effectiveness of enhanced anaerobic source zone bioremediation at chloroethene contaminated sites to determine if the treatment prevented contaminant rebound and removed NAPL from the source zone. Long-term performance was evaluated based on achieving MCL-based contaminant mass fluxes in parent compound concentrations during different monitoring periods. Groundwater concertation versus time data was compiled for 6-sites and post-remedial contaminant mass flux data was then measured using passive flux meters at wells both within and down-gradient of the source zone. Post-remedial mass flux data was then combined with pre-remedial water quality data to estimate pre-remedial mass flux. This information was used to characterize a DNAPL dissolution source strength function, such as the Power Law Model and the Equilibrium Stream tube model. The six-sites characterized for this study were (1) Former Charleston Air Force Base, Charleston, SC; (2) Dover Air Force Base, Dover, DE; (3) Treasure Island Naval Station, San Francisco, CA; (4) Former Raritan Arsenal, Edison, NJ; (5) Naval Air Station, Jacksonville, FL; and, (6) Former Naval Air Station, Alameda, CA. Contaminant mass fluxes decreased for all the sites by the end of the post-treatment monitoring period and rebound was limited within the source zone. Post remedial source strength function estimates suggest that decreases in contaminant mass flux will continue to occur at these sites, but a mass flux based on MCL levels may never be exceeded. Thus, site clean-up goals should be evaluated as order

  4. Body mass index, initial neurological severity and long-term mortality in ischemic stroke.

    Science.gov (United States)

    Ryu, Wi-Sun; Lee, Seung-Hoon; Kim, Chi Kyung; Kim, Beom Joon; Yoon, Byung-Woo

    2011-01-01

    Obesity is believed to increase the risks of ischemic stroke or coronary heart disease; however, regarding outcome after established vascular diseases, recent unexpected evidence has suggested that an increased body mass index (BMI) might have beneficial effects (obesity paradox). The aim of this study was to evaluate the independent association between BMI and long-term mortality after ischemic stroke. A total of 1,592 consecutive patients with ischemic stroke were prospectively included through our stroke cohort. In this study, the levels of BMI were classified based on guidelines for the Asian-Pacific population. Initial neurological severity was estimated by the National Institutes of Health Stroke Scale (NIHSS) score. Information on mortality was collected until the end of 2009, and the median follow-up period was 4 years. To examine the association between BMI and long-term mortality, we used Cox's proportional regression analysis. During follow-up, 23% of patients died. Linear regression analysis showed that the level of BMI was inversely related to initial neurological severity (p = 0.002). In the model of adjustment of age and gender using Cox's proportional regression analysis, this inverse trend was also significant (reference, normal weight; hazard ratio of underweight, 2.45; overweight, 0.77; obesity, 0.60). However, after adjustment of all covariates, including initial neurological severity, only the harmful effect of underweight remained significant (2.79; 95% CI, 1.92-4.05); however, beneficial effects of overweight and obesity did not. Our study showed that an independent association between BMI and long-term mortality after ischemic stroke was found only in underweight patients. The obesity paradox phenomenon seems to be limited, and might not be interpreted as a direct causal relationship due to a strong association with initial neurological severity. Copyright © 2011 S. Karger AG, Basel.

  5. Initial global 2-D shielding analysis for the Advanced Neutron Source core and reflector

    Energy Technology Data Exchange (ETDEWEB)

    Bucholz, J.A.

    1995-08-01

    This document describes the initial global 2-D shielding analyses for the Advanced Neutron Source (ANS) reactor, the D{sub 2}O reflector, the reflector vessel, and the first 200 mm of light water beyond the reflector vessel. Flux files generated here will later serve as source terms in subsequent shielding analyses. In addition to reporting fluxes and other data at key points of interest, a major objective of this report was to document how these analyses were performed, the phenomena that were included, and checks that were made to verify that these phenomena were properly modeled. In these shielding analyses, the fixed neutron source distribution in the core was based on the `lifetime-averaged` spatial power distribution. Secondary gamma production cross sections in the fuel were modified so as to account intrinsically for delayed fission gammas in the fuel as well as prompt fission gammas. In and near the fuel, this increased the low-energy gamma fluxes by 50 to 250%, but out near the reflector vessel, these same fluxes changed by only a few percent. Sensitivity studies with respect to mesh size were performed, and a new 2-D mesh distribution developed after some problems were discovered with respect to the use of numerous elongated mesh cells in the reflector. All of the shielding analyses were performed sing the ANSL-V 39n/44g coupled library with 25 thermal neutron groups in order to obtain a rigorous representation of the thermal neutron spectrum throughout the reflector. Because of upscatter in the heavy water, convergence was very slow. Ultimately, the fission cross section in the various materials had to be artificially modified in order to solve this fixed source problem as an eigenvalue problem and invoke the Vondy error-mode extrapolation technique which greatly accelerated convergence in the large 2-D RZ DORT analyses. While this was quite effective, 150 outer iterations (over energy) were still required.

  6. Initial global 2-D shielding analysis for the Advanced Neutron Source core and reflector

    International Nuclear Information System (INIS)

    Bucholz, J.A.

    1995-08-01

    This document describes the initial global 2-D shielding analyses for the Advanced Neutron Source (ANS) reactor, the D 2 O reflector, the reflector vessel, and the first 200 mm of light water beyond the reflector vessel. Flux files generated here will later serve as source terms in subsequent shielding analyses. In addition to reporting fluxes and other data at key points of interest, a major objective of this report was to document how these analyses were performed, the phenomena that were included, and checks that were made to verify that these phenomena were properly modeled. In these shielding analyses, the fixed neutron source distribution in the core was based on the 'lifetime-averaged' spatial power distribution. Secondary gamma production cross sections in the fuel were modified so as to account intrinsically for delayed fission gammas in the fuel as well as prompt fission gammas. In and near the fuel, this increased the low-energy gamma fluxes by 50 to 250%, but out near the reflector vessel, these same fluxes changed by only a few percent. Sensitivity studies with respect to mesh size were performed, and a new 2-D mesh distribution developed after some problems were discovered with respect to the use of numerous elongated mesh cells in the reflector. All of the shielding analyses were performed sing the ANSL-V 39n/44g coupled library with 25 thermal neutron groups in order to obtain a rigorous representation of the thermal neutron spectrum throughout the reflector. Because of upscatter in the heavy water, convergence was very slow. Ultimately, the fission cross section in the various materials had to be artificially modified in order to solve this fixed source problem as an eigenvalue problem and invoke the Vondy error-mode extrapolation technique which greatly accelerated convergence in the large 2-D RZ DORT analyses. While this was quite effective, 150 outer iterations (over energy) were still required

  7. Inventory and source term evaluation of Russian nuclear power plants for marine applications

    International Nuclear Information System (INIS)

    Reistad, O.; Oelgaard, P.L.

    2006-04-01

    This report discusses inventory and source term properties in regard to operation and possible releases due to accidents from Russian marine reactor systems. The first part of the report discusses relevant accidents on the basis of both Russian and western sources. The overview shows that certain vessels were much more accident prone compared to others, in addition, there have been a noteworthy reduction in accidents the last two decades. However, during the last years new types of incidents, such as collisions, has occurred more frequently. The second part of the study considers in detail the most important factors for the source term; reactor operational characteristics and the radionuclide inventory. While Russian icebreakers has been operated on a similar basis as commercial power plants, the submarines has different power cyclograms which results in considerable lower values for fission product inventory. Theoretical values for radionuclide inventory are compared with computed results using the modelling tool HELIOS. Regarding inventory of transuranic elements, the results of the calculations are discussed in detail for selected vessels. Criticality accidents, loss-of-cooling accidents and sinking accidents are considered, bases on actual experiences with these types of accident and on theoretical considerations, and source terms for these accidents are discussed in the last chapter. (au)

  8. Inventory and source term evaluation of Russian nuclear power plants for marine applications

    Energy Technology Data Exchange (ETDEWEB)

    Reistad, O. [Norwegian Radiation Protection Authority (Norway); Oelgaard, P.L. [Risoe National Lab. (Denmark)

    2006-04-15

    This report discusses inventory and source term properties in regard to operation and possible releases due to accidents from Russian marine reactor systems. The first part of the report discusses relevant accidents on the basis of both Russian and western sources. The overview shows that certain vessels were much more accident prone compared to others, in addition, there have been a noteworthy reduction in accidents the last two decades. However, during the last years new types of incidents, such as collisions, has occurred more frequently. The second part of the study considers in detail the most important factors for the source term; reactor operational characteristics and the radionuclide inventory. While Russian icebreakers has been operated on a similar basis as commercial power plants, the submarines has different power cyclograms which results in considerable lower values for fission product inventory. Theoretical values for radionuclide inventory are compared with computed results using the modelling tool HELIOS. Regarding inventory of transuranic elements, the results of the calculations are discussed in detail for selected vessels. Criticality accidents, loss-of-cooling accidents and sinking accidents are considered, bases on actual experiences with these types of accident and on theoretical considerations, and source terms for these accidents are discussed in the last chapter. (au)

  9. Initial operating experience and recent development on the TRIUMF optically pumped polarized H- ion source

    International Nuclear Information System (INIS)

    Schmor, P.W.; Law, W.M.; Levy, C.D.P.; McDonald, M.

    1988-01-01

    A polarized H - ion source using optical pumping techniques has been developed at TRIUMF. This source was used to demonstrate (on an ion source test stand) the feasibility of producing 10- μA of ∼ 60% polarized H - ion beam in a dc mode suitable for injection into the TRIUMF cyclotron. The source has been installed in a 300 kV high voltage terminal connected to the cyclotron via a recently constructed beam transport line. A polarization of 80% is anticipated near the end of 1988 after the installation of a superconducting solenoid to the source. In this paper the authors describe the initial operating experience, recent developments, and the future plans for the TRIUMF optically pumped polarized ion source

  10. Source terms for airborne radioactivity arising from uranium mill wastes

    International Nuclear Information System (INIS)

    O'Riordan, M.C.; Downing, A.L.

    1978-01-01

    One of the problems in assessing the radiological impact of uranium milling is to determine the rates of release to the air of material from the various sources of radioactivity. Such source terms are required for modelling the transport of radioactive material in the atmosphere. Activity arises from various point and area sources in the mill itself and from the mill tailings. The state of the tailings changes in time from slurry to solid. A layer of water may be maintained over the solids during the life of the mine, and the tailings may be covered with inert material on abandonment. Releases may be both gaseous and particulate. This paper indicates ways in which radon emanation and the suspension of long-lived particulate activity might be quantified, and areas requiring further exploration are identified

  11. Unsplit schemes for hyperbolic conservation laws with source terms in one space dimension

    International Nuclear Information System (INIS)

    Papalexandris, M.V.; Leonard, A.; Dimotakis, P.E.

    1997-01-01

    The present work is concerned with an application of the theory of characteristics to conservation laws with source terms in one space dimension, such as the Euler equations for reacting flows. Space-time paths are introduced on which the flow/chemistry equations decouple to a characteristic set of ODE's for the corresponding homogeneous laws, thus allowing the introduction of functions analogous to the Riemann invariants in classical theory. The geometry of these paths depends on the spatial gradients of the solution. This particular decomposition can be used in the design of efficient unsplit algorithms for the numerical integration of the equations. As a first step, these ideas are implemented for the case of a scalar conservation law with a nonlinear source term. The resulting algorithm belongs to the class of MUSCL-type, shock-capturing schemes. Its accuracy and robustness are checked through a series of tests. The stiffness of the source term is also studied. Then, the algorithm is generalized for a system of hyperbolic equations, namely the Euler equations for reacting flows. A numerical study of unstable detonations is performed. 57 refs

  12. Challenges in defining a radiologic and hydrologic source term for underground nuclear test centers, Nevada Test Site, Nye County, Nevada

    International Nuclear Information System (INIS)

    Smith, D.K.

    1995-06-01

    The compilation of a radionuclide inventory for long-lived radioactive contaminants residual from nuclear testing provides a partial measure of the radiologic source term at the Nevada Test Site. The radiologic source term also includes potentially mobile short-lived radionuclides excluded from the inventory. The radiologic source term for tritium is known with accuracy and is equivalent to the hydrologic source term within the saturated zone. Definition of the total hydrologic source term for fission and activation products that have high activities for decades following underground testing involves knowledge and assumptions which are presently unavailable. Systematic investigation of the behavior of fission products, activation products and actinides under saturated or Partially saturated conditions is imperative to define a representative total hydrologic source term. This is particularly important given the heterogeneous distribution of radionuclides within testing centers. Data quality objectives which emphasize a combination of measurements and credible estimates of the hydrologic source term are a priority for near-field investigations at the Nevada Test Site

  13. Least-squares finite-element method for shallow-water equations with source terms

    Institute of Scientific and Technical Information of China (English)

    Shin-Jye Liang; Tai-Wen Hsu

    2009-01-01

    Numerical solution of shallow-water equations (SWE) has been a challenging task because of its nonlinear hyperbolic nature, admitting discontinuous solution, and the need to satisfy the C-property. The presence of source terms in momentum equations, such as the bottom slope and friction of bed, compounds the difficulties further. In this paper, a least-squares finite-element method for the space discretization and θ-method for the time integration is developed for the 2D non-conservative SWE including the source terms. Advantages of the method include: the source terms can be approximated easily with interpolation functions, no upwind scheme is needed, as well as the resulting system equations is symmetric and positive-definite, therefore, can be solved efficiently with the conjugate gradient method. The method is applied to steady and unsteady flows, subcritical and transcritical flow over a bump, 1D and 2D circular dam-break, wave past a circular cylinder, as well as wave past a hump. Computed results show good C-property, conservation property and compare well with exact solutions and other numerical results for flows with weak and mild gradient changes, but lead to inaccurate predictions for flows with strong gradient changes and discontinuities.

  14. Inverse kinetics method with source term for subcriticality measurements during criticality approach in the IPEN/MB-01 research reactor

    International Nuclear Information System (INIS)

    Loureiro, Cesar Augusto Domingues; Santos, Adimir dos

    2009-01-01

    In reactor physics tests which are performed at the startup after refueling the commercial PWRs, it is important to monitor subcriticality continuously during criticality approach. Reactivity measurements by the inverse kinetics method are widely used during the operation of a nuclear reactor and it is possible to perform an online reactivity measurement based on the point reactor kinetics equations. This technique is successful applied at sufficiently high power level or to a core without an external neutron source where the neutron source term in point reactor kinetics equations may be neglected. For operation at low power levels, the contribution of the neutron source must be taken into account and this implies the knowledge of a quantity proportional to the source strength, and then it should be determined. Some experiments have been performed in the IPEN/MB-01 Research Reactor for the determination of the Source Term, using the Least Square Inverse Kinetics Method (LSIKM). A digital reactivity meter which neglects the source term is used to calculate the reactivity and then the source term can be determined by the LSIKM. After determining the source term, its value can be added to the algorithm and the reactivity can be determined again, considering the source term. The new digital reactivity meter can be used now to monitor reactivity during the criticality approach and the measured value for the reactivity is more precise than the meter which neglects the source term. (author)

  15. Regulatory Technology Development Plan Sodium Fast Reactor. Mechanistic Source Term Development

    Energy Technology Data Exchange (ETDEWEB)

    Grabaskas, David S. [Argonne National Lab. (ANL), Argonne, IL (United States); Brunett, Acacia Joann [Argonne National Lab. (ANL), Argonne, IL (United States); Bucknor, Matthew D. [Argonne National Lab. (ANL), Argonne, IL (United States); Sienicki, James J. [Argonne National Lab. (ANL), Argonne, IL (United States); Sofu, Tanju [Argonne National Lab. (ANL), Argonne, IL (United States)

    2015-02-28

    Construction and operation of a nuclear power installation in the U.S. requires licensing by the U.S. Nuclear Regulatory Commission (NRC). A vital part of this licensing process and integrated safety assessment entails the analysis of a source term (or source terms) that represents the release of radionuclides during normal operation and accident sequences. Historically, nuclear plant source term analyses have utilized deterministic, bounding assessments of the radionuclides released to the environment. Significant advancements in technical capabilities and the knowledge state have enabled the development of more realistic analyses such that a mechanistic source term (MST) assessment is now expected to be a requirement of advanced reactor licensing. This report focuses on the state of development of an MST for a sodium fast reactor (SFR), with the intent of aiding in the process of MST definition by qualitatively identifying and characterizing the major sources and transport processes of radionuclides. Due to common design characteristics among current U.S. SFR vendor designs, a metal-fuel, pool-type SFR has been selected as the reference design for this work, with all phenomenological discussions geared toward this specific reactor configuration. This works also aims to identify the key gaps and uncertainties in the current knowledge state that must be addressed for SFR MST development. It is anticipated that this knowledge state assessment can enable the coordination of technology and analysis tool development discussions such that any knowledge gaps may be addressed. Sources of radionuclides considered in this report include releases originating both in-vessel and ex-vessel, including in-core fuel, primary sodium and cover gas cleanup systems, and spent fuel movement and handling. Transport phenomena affecting various release groups are identified and qualitatively discussed, including fuel pin and primary coolant retention, and behavior in the cover gas and

  16. Source terms for analysis of accidents at a high level waste repository

    International Nuclear Information System (INIS)

    Mubayi, V.; Davis, R.E.; Youngblood, R.

    1989-01-01

    This paper describes an approach to identifying source terms from possible accidents during the preclosure phase of a high-level nuclear waste repository. A review of the literature on repository safety analyses indicated that source term estimation is in a preliminary stage, largely based on judgement-based scoping analyses. The approach developed here was to partition the accident space into domains defined by certain threshold values of temperature and impact energy density which may arise in potential accidents and specify release fractions of various radionuclides, present in the waste form, in each domain. Along with a more quantitative understanding of accident phenomenology, this approach should help in achieving a clearer perspective on scenarios important to preclosure safety assessments of geologic repositories. 18 refs., 3 tabs

  17. Long-term dust aerosol production from natural sources in Iceland.

    Science.gov (United States)

    Dagsson-Waldhauserova, Pavla; Arnalds, Olafur; Olafsson, Haraldur

    2017-02-01

    Iceland is a volcanic island in the North Atlantic Ocean with maritime climate. In spite of moist climate, large areas are with limited vegetation cover where >40% of Iceland is classified with considerable to very severe erosion and 21% of Iceland is volcanic sandy deserts. Not only do natural emissions from these sources influenced by strong winds affect regional air quality in Iceland ("Reykjavik haze"), but dust particles are transported over the Atlantic ocean and Arctic Ocean >1000 km at times. The aim of this paper is to place Icelandic dust production area into international perspective, present long-term frequency of dust storm events in northeast Iceland, and estimate dust aerosol concentrations during reported dust events. Meteorological observations with dust presence codes and related visibility were used to identify the frequency and the long-term changes in dust production in northeast Iceland. There were annually 16.4 days on average with reported dust observations on weather stations within the northeastern erosion area, indicating extreme dust plume activity and erosion within the northeastern deserts, even though the area is covered with snow during the major part of winter. During the 2000s the highest occurrence of dust events in six decades was reported. We have measured saltation and Aeolian transport during dust/volcanic ash storms in Iceland, which give some of the most intense wind erosion events ever measured. Icelandic dust affects the ecosystems over much of Iceland and causes regional haze. It is likely to affect the ecosystems of the oceans around Iceland, and it brings dust that lowers the albedo of the Icelandic glaciers, increasing melt-off due to global warming. The study indicates that Icelandic dust may contribute to the Arctic air pollution. Long-term records of meteorological dust observations from Northeast Iceland indicate the frequency of dust events from Icelandic deserts. The research involves a 60-year period and

  18. Source-term characterisation and solid speciation of plutonium at the Semipalatinsk NTS, Kazakhstan.

    Science.gov (United States)

    Nápoles, H Jiménez; León Vintró, L; Mitchell, P I; Omarova, A; Burkitbayev, M; Priest, N D; Artemyev, O; Lukashenko, S

    2004-01-01

    New data on the concentrations of key fission/activation products and transuranium nuclides in samples of soil and water from the Semipalatinsk Nuclear Test Site are presented and interpreted. Sampling was carried out at Ground Zero, Lake Balapan, the Tel'kem craters and reference locations within the test site boundary well removed from localised sources. Radionuclide ratios have been used to characterise the source term(s) at each of these sites. The geochemical partitioning of plutonium has also been examined and it is shown that the bulk of the plutonium contamination at most of the sites examined is in a highly refractory, non-labile form.

  19. Source-term characterisation and solid speciation of plutonium at the Semipalatinsk NTS, Kazakhstan

    Energy Technology Data Exchange (ETDEWEB)

    Napoles, H.J.H. Jimenez; Leon Vintro, L. E-mail: luis.leon@ucd.ie; Mitchell, P.I.; Omarova, A.; Burkitbayev, M.; Priest, N.D.; Artemyev, O.; Lukashenko, S

    2004-09-01

    New data on the concentrations of key fission/activation products and transuranium nuclides in samples of soil and water from the Semipalatinsk Nuclear Test Site are presented and interpreted. Sampling was carried out at Ground Zero, Lake Balapan, the Tel'kem craters and reference locations within the test site boundary well removed from localised sources. Radionuclide ratios have been used to characterise the source term(s) at each of these sites. The geochemical partitioning of plutonium has also been examined and it is shown that the bulk of the plutonium contamination at most of the sites examined is in a highly refractory, non-labile form.

  20. Global existence and nonexistence for the viscoelastic wave equation with nonlinear boundary damping-source interaction

    KAUST Repository

    Said-Houari, Belkacem

    2012-09-01

    The goal of this work is to study a model of the viscoelastic wave equation with nonlinear boundary/interior sources and a nonlinear interior damping. First, applying the Faedo-Galerkin approximations combined with the compactness method to obtain existence of regular global solutions to an auxiliary problem with globally Lipschitz source terms and with initial data in the potential well. It is important to emphasize that it is not possible to consider density arguments to pass from regular to weak solutions if one considers regular solutions of our problem where the source terms are locally Lipschitz functions. To overcome this difficulty, we use an approximation method involving truncated sources and adapting the ideas in [13] to show that the existence of weak solutions can still be obtained for our problem. Second, we show that under some restrictions on the initial data and if the interior source dominates the interior damping term, then the solution ceases to exist and blows up in finite time provided that the initial data are large enough.

  1. Global existence and nonexistence for the viscoelastic wave equation with nonlinear boundary damping-source interaction

    KAUST Repository

    Said-Houari, Belkacem; Nascimento, Flá vio A Falcã o

    2012-01-01

    The goal of this work is to study a model of the viscoelastic wave equation with nonlinear boundary/interior sources and a nonlinear interior damping. First, applying the Faedo-Galerkin approximations combined with the compactness method to obtain existence of regular global solutions to an auxiliary problem with globally Lipschitz source terms and with initial data in the potential well. It is important to emphasize that it is not possible to consider density arguments to pass from regular to weak solutions if one considers regular solutions of our problem where the source terms are locally Lipschitz functions. To overcome this difficulty, we use an approximation method involving truncated sources and adapting the ideas in [13] to show that the existence of weak solutions can still be obtained for our problem. Second, we show that under some restrictions on the initial data and if the interior source dominates the interior damping term, then the solution ceases to exist and blows up in finite time provided that the initial data are large enough.

  2. Fission product source term research at Oak Ridge National Laboratory

    International Nuclear Information System (INIS)

    Malinauskas, A.P.

    1985-01-01

    The purpose of this work is to describe some of the research being performed at ORNL in support of the effort to describe, as realistically as possible, fission product source terms for nuclear reactor accidents. In order to make this presentation manageable, only those studies directly concerned with fission product behavior, as opposed to thermal hydraulics, accident sequence progression, etc., will be discussed

  3. Proposal for implementation of alternative source term in the nuclear power plant of Laguna Verde

    International Nuclear Information System (INIS)

    Bazan L, A.; Lopez L, M.; Vargas A, A.; Cardenas J, J. B.

    2009-10-01

    In 2010 the nuclear power plant of Laguna Verde will implement the extended power upbeat in both units of the plant. Agree with methodology of NEDC-33004P-A, (constant pressure power up rate), and the source term of core, for accidents evaluations, were increased in proportion to the ratio of power level. This means that for the case of a design basis accident of loss of coolant an increase of power of 15% originated an increase of 15% in dose to main control room. Using the method of NEDC-33004P-A to extended power upbeat conditions was determined that the dose value to main control room is very near to regulatory limit established by SRP 6.4. By the above and in order to recover the margin, the nuclear power plant of Laguna Verde will calculate an alternative source term following the criteria established in RG 1.183 (alternative radiological source term for evaluating DBA at nuclear power reactor). This approach also have a more realistic dose value using the criterion of 10-CFR-50.67, in addition is predicted to get the benefit of additional operational flexibilities. This paper present the proposal of implementing the alternative source term in Laguna Verde. (Author)

  4. Review of the accident source terms for aluminide fuel: Application to the BR2 reactor

    International Nuclear Information System (INIS)

    Joppen, F.

    2005-01-01

    A major safety review of the BR2, a material test reactor, is to be conducted for the year 2006. One of the subjects selected for the safety review is the definition of source terms for emergency planning and in particular the development of accident scenarios. For nuclear power plants the behaviour of fuel under accident conditions is a well studied object. In case of non-power reactors this basic knowledge is rather scarce. The usefulness of information from power plant fuels is limited due to the differences in fuel type, power level and thermohydraulical conditions. First investigation indicates that using data from power plant fuel leads to an overestimation of the source terms. Further research on this subject could be very useful for the research reactor community, in order to define more realistic source terms and to improve the emergency preparedness. (author)

  5. The long-term relationships among China's energy consumption sources and adjustments to its renewable energy policy

    International Nuclear Information System (INIS)

    Zou Gaolu

    2012-01-01

    To reduce its consumption of coal and oil in its primary energy consumption, China promotes the development of renewable energy resources. I have analysed the long-term relationship among China's primary energy consumption sources. Changes in coal consumption lead those in the consumption of other energy sources in the long term. Coal and oil fuels substitute for each other equally. The long-term elasticities of China's coal consumption relative to its hydroelectricity consumption were greater than one and nearly equal during the two sample periods. Therefore, increased hydroelectricity consumption did not imply a reduction in coal consumption. China holds abundant hydroelectricity, wind and, solar energy potential. China must prevent an excessive escalation of its economy and resultant energy demand to realise a meaningful substitution of coal with hydroelectricity. Moreover, China must develop and use wind and solar energy sources. Natural gas can be a good substitute for coal, given its moderate price growth and affordable price levels. - Highlights: ► Coal consumption changes lead those of other energy sources in the long term. ► Coal and oil fuels substitute for each other equally. ► Increased hydroelectricity consumption has not meant lower coal consumption. ► Wind, solar and natural gas are China's promising energy sources.

  6. Development of Level-2 PSA Technology: A Development of the Database of the Parametric Source Term for Kori Unit 1 Using the MAAP4 Code

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Chang Soon; Mun, Ju Hyun; Yun, Jeong Ick; Cho, Young Hoo; Kim, Chong Uk [Seoul National University, Seoul (Korea, Republic of)

    1997-07-15

    To quantify the severe accident source term of the parametric model method, the uncertainty of the parameters should be analyzed. Generally, to analyze the uncertainties, the cumulative distribution functions(CDF`S) of the parameters are derived. This report introduces a method of derivation of the CDF`s of the basic parameters, FCOR, FVES and FDCH. The calculation tool of the source term is the MAAP version 4.0. In the MAAP code, there are model parameters to consider an uncertain physical and/or chemical phenomenon. In general, the parameters have not a point value but a range. In this paper, considering this point, the input values of model parameters influencing each parameter are sampled using LHS. Then, the calculation results are shown in the cumulative distribution form. For a case study, the CDF`s of FCOR, FVES and FDCH of KORI unit 1 are derived. The target scenarios for the calculation are the ones whose initial events are large LOCA, small LOCA and transient, respectively. It is found that the distributions of this study are consistent to those of NUREG-1150 and are proven to be adequate in assessing the uncertainties in the severe accident source term of KORI Unit 1. 15 refs., 27 tabs., 4 figs. (author)

  7. Development of in-vessel source term analysis code, tracer

    International Nuclear Information System (INIS)

    Miyagi, K.; Miyahara, S.

    1996-01-01

    Analyses of radionuclide transport in fuel failure accidents (generally referred to source terms) are considered to be important especially in the severe accident evaluation. The TRACER code has been developed to realistically predict the time dependent behavior of FPs and aerosols within the primary cooling system for wide range of fuel failure events. This paper presents the model description, results of validation study, the recent model advancement status of the code, and results of check out calculations under reactor conditions. (author)

  8. Quantification of source-term profiles from near-field geochemical models

    International Nuclear Information System (INIS)

    McKinley, I.G.

    1985-01-01

    A geochemical model of the near-field is described which quantitatively treats the processes of engineered barrier degradation, buffering of aqueous chemistry by solid phases, nuclide solubilization and transport through the near-field and release to the far-field. The radionuclide source-terms derived from this model are compared with those from a simpler model used for repository safety analysis. 10 refs., 2 figs., 2 tabs

  9. Modelling and simulation the radioactive source-term of fission products in PWR type reactors

    International Nuclear Information System (INIS)

    Porfirio, Rogilson Nazare da Silva

    1996-01-01

    The source-term was defined with the purpose the quantify all radioactive nuclides released the nuclear reactor in the case of accidents. Nowadays the source-term is limited to the coolant of the primary circuit of reactors and may be measured or modelled with computer coders such as the TFP developed in this work. The calculational process is based on the linear chain techniques used in the CINDER-2 code. The TFP code considers forms of fission products release from the fuel pellet: Recoil, Knockout and Migration. The release from the gap to the coolant fluid is determined from the ratio between activity measured in the coolant and calculated activity in the gap. Considered the operational data of SURRY-1 reactor, the TFP code was run to obtain the source=term of this reactor. From the measured activities it was verified the reliability level of the model and the employed computational logic. The accuracy of the calculated quantities were compared to the measured data was considered satisfactory. (author)

  10. Initial assessment of MHTGR confinement releases

    International Nuclear Information System (INIS)

    Maneke, J.L.; Lanning, D.D.; Lidsky, L.M.

    1986-01-01

    Initial investigation of Modular High Temperature Gas-Cooled Reactor (MHTGR) designs suggest that source terms during postulated accidents will be considerably lower than Light Water Reactor (LWR) source term estimates. These lower postulated accident releases are not only a safety incentive, but also an economic incentive for the development of this reactor type. For example, it is hoped that a filtered confinement building, rather than a more expensive LWR-like containment building, would adequately protect the public from radiological releases. The ability of a confinement building to satisfy safety requirements for the MHTGR depends on several reactor parameters, such as fuel quality, reactor design, and the design of the reactor building. SCIMCA, a Simple Code for Initial MHTGR Confinement Assessment has been developed for preliminary MHTGR building requirement calculations. The code is capable of modeling a decay chain with a maximum of five regions. Phenomena such as fission product decay and buildup, natural deposition, building filtration, and intercompartmental transport are incorporated. SCIMCA models reduction mechanisms, such as dispersion and decay, occurring as radioactivity is transported through the environment. A subroutine for calculating doses at specified distances has also been included

  11. Analysis of safety information for nuclear power plants and development of source term estimation program

    International Nuclear Information System (INIS)

    Kim, Tae Woon; Choi, Seong Soo; Park, Jin Hee

    1999-12-01

    Current CARE(Computerized Advisory System for Radiological Emergency) in KINS(Korea Institute of Nuclear Safety) has no STES(Source Term Estimation System) which links between SIDS(Safety Information Display System) and FADAS(Following Accident Dose Assessment System). So in this study, STES is under development. STES system is the system that estimates the source term based on the safety information provided by SIDS. Estimated source term is given to FADAS as an input for estimation of environmental effect of radiation. Through this first year project STES for the Kori 3,4 and Younggwang 1,2 has been developed. Since there is no CARE for Wolsong(PHWR) plants yet, CARE for Wolsong is under construction. The safety parameters are selected and the safety information display screens and the alarm logic for plant status change are developed for Wolsong Unit 2 based on the design documents for CANDU plants

  12. The Spallation Neutron Source Beam Commissioning and Initial Operations

    Energy Technology Data Exchange (ETDEWEB)

    Henderson, Stuart [Argonne National Lab. (ANL), Argonne, IL (United States); Aleksandrov, Alexander V. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Allen, Christopher K. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Assadi, Saeed [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bartoski, Dirk [University of Texas, Houston, TX (United States). Anderson Cancer Center; Blokland, Willem [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Casagrande, F. [Michigan State Univ., East Lansing, MI (United States); Campisi, I. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Chu, C. [Michigan State Univ., East Lansing, MI (United States); Cousineau, Sarah M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Crofford, Mark T. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Danilov, Viatcheslav [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Deibele, Craig E. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Dodson, George W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Feshenko, A. [Inst. for Nuclear Research (INR), Moscow (Russian Federation); Galambos, John D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Han, Baoxi [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hardek, T. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Holmes, Jeffrey A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Holtkamp, N. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Howell, Matthew P. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jeon, D. [Inst. for Basic Science, Daejeon (Korea); Kang, Yoon W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kasemir, Kay [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kim, Sang-Ho [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kravchuk, L. [Institute for Nuclear Research (INR), Moscow (Russian Federation); Long, Cary D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); McManamy, T. [McManamy Consulting, Inc., Middlesex, MA (United States); Pelaia, II, Tom [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Piller, Chip [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Plum, Michael A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Pogge, James R. [Tennessee Technological Univ., Cookeville, TN (United States); Purcell, John David [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Shea, T. [European Spallation Source, Lund (Sweden); Shishlo, Andrei P [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Sibley, C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Stockli, Martin P. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Stout, D. [Michigan State Univ., East Lansing, MI (United States); Tanke, E. [European Spallation Source, Lund (Sweden); Welton, Robert F [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Zhang, Y. [Michigan State Univ., East Lansing, MI (United States); Zhukov, Alexander P [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-09-01

    The Spallation Neutron Source (SNS) accelerator delivers a one mega-Watt beam to a mercury target to produce neutrons used for neutron scattering materials research. It delivers ~ 1 GeV protons in short (< 1 us) pulses at 60 Hz. At an average power of ~ one mega-Watt, it is the highest-powered pulsed proton accelerator. The accelerator includes the first use of superconducting RF acceleration for a pulsed protons at this energy. The storage ring used to create the short time structure has record peak particle per pulse intensity. Beam commissioning took place in a staged manner during the construction phase of SNS. After the construction, neutron production operations began within a few months, and one mega-Watt operation was achieved within three years. The methods used to commission the beam and the experiences during initial operation are discussed.

  13. DNA evolutionary algorithm (DNAEA) for source term identification in convection-diffusion equation

    International Nuclear Information System (INIS)

    Yang, X-H; Hu, X-X; Shen, Z-Y

    2008-01-01

    The source identification problem is changed into an optimization problem in this paper. This is a complicated nonlinear optimization problem. It is very intractable with traditional optimization methods. So DNA evolutionary algorithm (DNAEA) is presented to solve the discussed problem. In this algorithm, an initial population is generated by a chaos algorithm. With the shrinking of searching range, DNAEA gradually directs to an optimal result with excellent individuals obtained by DNAEA. The position and intensity of pollution source are well found with DNAEA. Compared with Gray-coded genetic algorithm and pure random search algorithm, DNAEA has rapider convergent speed and higher calculation precision

  14. A source-initiated on-demand routing algorithm based on the Thorup-Zwick theory for mobile wireless sensor networks.

    Science.gov (United States)

    Mao, Yuxin; Zhu, Ping

    2013-01-01

    The unreliability and dynamics of mobile wireless sensor networks make it hard to perform end-to-end communications. This paper presents a novel source-initiated on-demand routing mechanism for efficient data transmission in mobile wireless sensor networks. It explores the Thorup-Zwick theory to achieve source-initiated on-demand routing with time efficiency. It is able to find out shortest routing path between source and target in a network and transfer data in linear time. The algorithm is easy to be implemented and performed in resource-constrained mobile wireless sensor networks. We also evaluate the approach by analyzing its cost in detail. It can be seen that the approach is efficient to support data transmission in mobile wireless sensor networks.

  15. Derivation of the source term, dose results and associated radiological consequences for the Greek Research Reactor – 1

    Energy Technology Data Exchange (ETDEWEB)

    Pappas, Charalampos, E-mail: chpappas@ipta.demokritos.gr; Ikonomopoulos, Andreas; Sfetsos, Athanasios; Andronopoulos, Spyros; Varvayanni, Melpomeni; Catsaros, Nicolas

    2014-07-01

    Highlights: • Source term derivation of postulated accident sequences in a research reactor. • Various containment ventilation scenarios considered for source term calculations. • Source term parametric analysis performed in case of lack of ventilation. • JRODOS employed for dose calculations under eighteen modeled scenarios. • Estimation of radiological consequences during typical and adverse weather scenarios. - Abstract: The estimated source term, dose results and radiological consequences of selected accident sequences in the Greek Research Reactor – 1 are presented and discussed. A systematic approach has been adopted to perform the necessary calculations in accordance with the latest computational developments and IAEA recommendations. Loss-of-coolant, reactivity insertion and fuel channel blockage accident sequences have been selected to derive the associated source terms under three distinct containment ventilation scenarios. Core damage has been conservatively assessed for each accident sequence while the ventilation has been assumed to function within the efficiency limits defined at the Safety Analysis Report. In case of lack of ventilation a parametric analysis is also performed to examine the dependency of the source term on the containment leakage rate. A typical as well as an adverse meteorological scenario have been defined in the JRODOS computational platform in order to predict the effective, lung and thyroid doses within a region defined by a 15 km radius downwind from the reactor building. The radiological consequences of the eighteen scenarios associated with the accident sequences are presented and discussed.

  16. Source term and activation calculations for the new TR-FLEX cyclotron for medical applications at HZDR

    Energy Technology Data Exchange (ETDEWEB)

    Konheiser, Joerg [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Reactor Safety; Ferrari, A. [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Inst. of Radiation Physics; Magin, A. [Karlsruher Institut fuer Technologie (KIT), Karlsruhe (Germany); Naumann, B. [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Dept. of Radiation Protection and Safety; Mueller, S.E.

    2017-06-01

    The neutron source terms for a proton beam hitting an {sup 18}O-enriched water target were calculated with the radiation transport programs MCNP6 and FLUKA and were compared to source terms for exclusive {sup 18}O(p,n){sup 18}F production. To validate the radiation fields obtained in the simulations, an experimental program has been started using activation samples originally used in reactor dosimetry.

  17. ITER task title - source term data, modelling, and analysis. ITER subtask no. S81TT05/5 (SEP 1-1). Global tritium source term analysis basis document. Subtask 1: operational tritium effluents and releases. Final report (1995 TASK)

    International Nuclear Information System (INIS)

    Kalyanam, K.M.

    1996-06-01

    This document represents the final report for the global tritium source term analysis task initiated in 1995. The report presents a room-by-room map/table at the subsystem level for the ITER tritium systems, identifying the major equipment, secondary containments, tritium release sources, duration/frequency of tritium releases and the release pathways. The chronic tritium releases during normal operation, as well as tritium releases due to routine maintenance of the Water Distillation Unit, Isotope Separation System and Primary and Secondary Heat Transport Systems, have been estimated for most of the subsystems, based on the IDR design, the Design Description Documents (April - Jun 1995 issues) and the design updates up to December 1995. The report also outlines the methodology and the key assumptions that are adopted in preparing the tritium release estimates. The design parameters for the ITER Basic Performance Phase (BPP) have been used in estimating the tritium releases shown in the room-by-room map/table. The tritium release calculations and the room-by-room map/table have been prepared in EXCEL, so that the estimates can be refined easily as the design evolves and more detailed information becomes available. (author). 23 refs., tabs

  18. Review and evaluation of the Millstone Unit 3 probabilistic safety study. Containment failure modes, radiological source - terms and offsite consequences

    International Nuclear Information System (INIS)

    Khatib-Rahbar, M.; Pratt, W.; Ludewig, H.

    1985-09-01

    A technical review and evaluation of the Millstone Unit 3 probabilistic safety study has been performed. It was determined that; (1) long-term damage indices (latent fatalities, person-rem, etc.) are dominated by late failure of the containment, (2) short-term damage indices (early fatalities, etc.) are dominated by bypass sequences for internally initiated events, while severe seismic sequences can also contribute significantly to early damage indices. These overall estimates of severe accident risk are extremely low compared with other societal sources of risk. Furthermore, the risks for Millstone-3 are comparable to risks from other nuclear plants at high population sites. Seismically induced accidents dominate the severe accident risks at Millstone-3. Potential mitigative features were shown not to be cost-effective for internal events. Value-impact analysis for seismic events showed that a manually actuated containment spray system might be cost-effective

  19. Use of source term uncoupled in radionuclide migration equations

    International Nuclear Information System (INIS)

    Silveira, Claudia Siqueira da; Lima, Zelmo Rodrigues de; Alvim, Antonio Carlos Marques

    2008-01-01

    Final repositories of high-level radioactive waste have been considered in deep, low permeability and stable geological formations. A common problem found is the migration modeling of radionuclides in a fractured rock. In this work, the physical system adopted consists of the rock matrix containing a single planar fracture situated in water saturated porous rock. The partial differential equations that describe the radionuclide transport were discretized using finite differences techniques, of which the following methods were adopted: Explicit Euler, Implicit Euler and Crank-Nicholson. For each one of these methods, the advective term was discretized with the following numerical schemes: backward differences, centered differences and forward differences. We make a comparison to determine which temporal and space discretization has the best result in relation to a reference solution. The obtained results show that the Explicit Euler Method with forward discretization in the advective term has a good accuracy. Next, with the objective of improving the answer of the Implicit Euler and Crank-Nicholson Methods it was accomplished a source term uncouplement, the diffusive flux. The obtained results were considered satisfactory by comparison with previous studies. (author)

  20. Short-term X-ray variability of the globular cluster source 4U 1820 - 30 (NGC 6624)

    Science.gov (United States)

    Stella, L.; Kahn, S. M.; Grindlay, J. E.

    1984-01-01

    Analytical techniques for improved identification of the temporal and spectral variability properties of globular cluster and galactic bulge X-ray sources are described in terms of their application to a large set of observations of the source 4U 1820 - 30 in the globular cluster NGC 6624. The autocorrelation function, cross-correlations, time skewness function, erratic periodicities, and pulse trains are examined. The results are discussed in terms of current models with particular emphasis on recent accretion disk models. It is concluded that the analyzed observations provide the first evidence for shot-noise variability in a globular cluster X-ray source.

  1. Influence of Chemistry on source term assessment

    International Nuclear Information System (INIS)

    Herranz Puebla, L.E.; Lopez Diez, I.; Rodriguez Maroto, J.J.; Martinez Lopez-Alcorocho, A.

    1991-01-01

    The major goal of a phenomenology analysis of containment during a severe accident situation can be splitedd into the following ones: to know the containment response to the different loads and to predict accurately the fission product and aerosol behavior. In this report, the main results coming from the study of a hypothetical accident scenario, based on LA-4 experiment of LACE project, are presented. In order to do it, several codes have been coupled: CONTEMPT4/MOD5 (thermalhydraulics), NAUA/MOD5 (aerosol physics) and IODE (iodine chemistry). 12 refs. It has been demonstrated the impossibility of assessing with confidence the Source Term if the chemical conduct of some radionuclides is not taken into account. In particular, the influence on the iodine retention efficiency of the sump of variables such as pH has been proven. (Author). 12 refs

  2. Ion source memory in {sup 36}Cl accelerator mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Pavetich, Stefan; Akhmadaliev, Shavkat; Merchel, Silke; Rugel, Georg [HZDR, Dresden (Germany); Arnold, Maurice; Aumaitre, Georges; Bourles, Didier; Martschini, Martin [ASTER, Aix-en-Provence (France); Buchriegler, Josef; Golser, Robin; Keddadouche, Karim; Steier, Peter [VERA, Vienna (Austria)

    2013-07-01

    Since the DREAMS (Dresden Accelerator Mass Spectrometry) facility went operational in 2011, constant effort was put into enabling routine measurements of long-lived radionuclides as {sup 10}Be, {sup 26}Al and {sup 41}Ca. For precise AMS-measurements of the volatile element Cl the key issue is the minimization of the long term memory effect. For this purpose one of the two original HVE sources was mechanically modified, allowing the usage of bigger cathodes with individual target apertures. Additionally a more open geometry was used to improve the vacuum level. To evaluate this improvement in comparison to other up-to-date ion sources, a small inter-laboratory comparison had been initiated. The long-term memory effect in the Cs sputter ion sources of the AMS facilities VERA, ASTER and DREAMS had been investigated by running samples of natural {sup 35}Cl/{sup 37}Cl-ratio and samples containing highly enriched {sup 35}Cl({sup 35}Cl/{sup 37}Cl > 500). Primary goals of the research are the time constants of the recovery from the contaminated sample ratio to the initial ratio of the sample and the level of the long-term memory effect in the sources.

  3. SARNET. Severe Accident Research Network - key issues in the area of source term

    International Nuclear Information System (INIS)

    Giordano, P.; Micaelli, J.C.; Haste, T.; Herranz, L.

    2005-01-01

    About fifty European organisations integrate in SARNET (Network of Excellence of the EU 6 th Framework Programme) their research capacities in resolve better the most important remaining uncertainties and safety issues concerning existing and future Nuclear Power Plants (NPPs) under hypothetical Severe Accident (SA) conditions. Wishing to maintain a long-lasting cooperation, they conduct three types of activities: integrating activities, spreading of excellence and jointly executed research. This paper summarises the main results obtained by the network after the first year, giving more prominence to those from jointly executed research in the Source Term area. Integrating activities have been performed through different means: the ASTEC integral computer code for severe accident transient modelling, through development of PSA2 methodologies, through the setting of a structure for definition of evolving R and D priorities and through the development of a web-network of data bases that hosts experimental data. Such activities have been facilitated by the development of an Advanced Communication Tool. Concerning spreading of excellence, educational courses covering Severe Accident Analysis Methodology and Level 2 PSA have been set up, to be given in early 2006. A detailed text book on Severe Accident Phenomenology has been designed and agreed amongst SARNET members. A mobility programme for students and young researchers is being developed, some detachments are already completed or in progress, and examples are quoted. Jointly executed research activities concern key issues grouped in the Corium, Containment and Source Term areas. In Source Term, behaviour of the highly radio-toxic ruthenium under oxidising conditions (like air ingress) for HBU and MOX fuel has been investigated. First modelling proposals for ASTEC have been made for oxidation of fuel and of ruthenium. Experiments on transport of highly volatile oxide ruthenium species have been performed. Reactor

  4. Evaluation of applicability of alternative source terms to operating nuclear power plants in Korea

    International Nuclear Information System (INIS)

    Lim, S. N.; Park, Y. S.; Nam, K. M.; Song, D. B.; Bae, Y. J.; Lee, Y. J.; Jung, C. Y.

    2002-01-01

    In 1995 and 2000, NRC issued NUREG-1465 and Regulatory Guide 1.183 with respect to Alternative Source Terms(AST) replacing the existing source terms of TID-14844 and Regulatory Guide 1.4, 1.25, and 1.77 for radiological Design Basis Accidents(DBA) analysis. In 1990, ICRP published ICRP Pub. 60 which represents new recommendations on dose criteria and concepts. In Korea, alternative source terms were used for evaluation of effective doses for design basis accidents of Advanced Power Reactor(APR1400) using the computer program developed by an overseas company. Recently, DBADOSE, new computer program for DBA analysis incorporating AST and effective dose concept was developed by KHNP and KOPEC, and reanalysis applying AST to operating nuclear power plants, Kori units 3 and 4 in Korea using DBADOSE has been performed. As the results of this analysis, it was concluded that some conservative variables or operation procedures of operating plants could be mitigated or simplified by virtue of increased safety margin and consequently, economical and operational benefits ensue. In this paper, methodologies and results of Kori 3 and 4 DBA reanalysis and sensitivity analysis for mitigation of main design variables are introduced

  5. Long term leaching of chlorinated solvents from source zones in low permeability settings with fractures

    DEFF Research Database (Denmark)

    Bjerg, Poul Løgstrup; Chambon, Julie Claire Claudia; Troldborg, Mads

    2008-01-01

    spreads to the low permeability matrix by diffusion. This results in a long term source of contamination due to back-diffusion. Leaching from such sources is further complicated by microbial degradation under anaerobic conditions to sequentially form the daughter products trichloroethylene, cis...

  6. Short-term Risk of Serious Fall Injuries in Older Adults Initiating and Intensifying Treatment with Antihypertensive Medication

    Science.gov (United States)

    Shimbo, Daichi; Bowling, C. Barrett; Levitan, Emily B.; Deng, Luqin; Sim, John J.; Huang, Lei; Reynolds, Kristi; Muntner, Paul

    2016-01-01

    Background Antihypertensive medication use has been associated with an increased risk of falls in some but not all studies. Few data are available on the short-term risk of falls following antihypertensive medication initiation and intensification. Methods and Results We examined the association between initiating and intensifying antihypertensive medication and serious fall injuries in a case-crossover study of 90,127 Medicare beneficiaries who were ≥65 years old and had a serious fall injury between July 1, 2007 and December 31, 2012, based on emergency department and inpatient claims. Antihypertensive medication initiation was defined by a prescription fill with no fills in the prior year. Intensification was defined by the addition of a new antihypertensive class, and, separately, titration by the addition of a new class or increase in dosage of a current class. Exposures were ascertained for the 15 days before the fall (case period) and six 15-day earlier periods (control periods). Overall, 272, 1508, and 3113 Medicare beneficiaries initiated, added a new class of antihypertensive medication or titrated therapy, respectively, within 15 days of their serious fall injury. The odds for a serious fall injury was increased during the 15 days following antihypertensive medication initiation [odds ratio, OR, 1.36 (95% CI 1.19, 1.55)], adding a new class [OR 1.16 (95% CI 1.10, 1.23)], and titration [OR 1.13 (95% CI 1.08, 1.18)]. These associations were attenuated beyond 15 days. Conclusions Antihypertensive medication initiation and intensification was associated with a short-term, but not long-term, increased risk of serious fall injuries among older adults. PMID:27166208

  7. Source term estimation based on in-situ gamma spectrometry using a high purity germanium detector

    International Nuclear Information System (INIS)

    Pauly, J.; Rojas-Palma, C.; Sohier, A.

    1997-06-01

    An alternative method to reconstruct the source term of a nuclear accident is proposed. The technique discussed here involves the use of in-situ gamma spectrometry. The validation of the applied methodology has been possible through the monitoring of routine releases of Ar-41 originating at a Belgian site from an air cooled graphite research reactor. This technique provides a quick nuclide specific decomposition of the source term and therefore will be have an enormous potential if implemented in nuclear emergency preparedness and radiological assessments of nuclear accidents during the early phase

  8. Initial Analyses of Change Detection Capabilities and Data Redundancies in the Long Term Resource Monitoring Program

    National Research Council Canada - National Science Library

    Lubinski, Kenneth

    2001-01-01

    Evaluations of Long Term Resource Monitoring Program sampling designs for water quality, fish, aquatic vegetation, and macroinvertebrates were initiated in 1999 by analyzing data collected since 1992...

  9. Safety and Security of Radioactive Sources: Initiatives of the Forum of Nuclear Regulatory Bodies in Africa (FNRBA)

    International Nuclear Information System (INIS)

    Severa, R.

    2010-01-01

    Safety and Security of Radioactive Sources: Initiatives of the Forum of Nuclear Regulatory Bodies in Africa(FNRBA) is a regional organization comprising of nuclear regulatory bodies it’s goals are to promote the establishment of regulatory infrastructure in all countries of the Region to adopt joint action plan for implementation of self-assessment and work with Member States to upgrade their regulatory infrastructures, develop and promote a framework for capacity building in areas of radiation and nuclear safety and security, to create an opportunity for mutual support and coordination of regional initiatives by leveraging the development and utilization of regional and international resources and expertise and to serve as reference body on matters relating to nuclear and radiation safety and security in the Region. Radioactive active sources continue to play an increasingly important role in socio-economic activities on the African continent. There is also an ever increasing need to ensure that radioactive sources are utilized in a safe and secure manner

  10. Operator aids for prediction of source term attenuation

    International Nuclear Information System (INIS)

    Powers, D.A.

    2004-01-01

    Simplified expressions for the attenuation of radionuclide releases by sprays and by water pools are devised. These expressions are obtained by correlation of the 10th, 50th and 90th percentiles of uncertainty distributions for the water pool decontamination factor and the spray decontamination coefficient. These uncertainty distributions were obtained by Monte Carlo uncertainty analyses using detailed, mechanistic models of the pools and sprays. Uncertainties considered in the analyses include uncertainties in the phenomena and uncertainties in the initial and boundary conditions dictated by the progression of severe accidents. Final results are graphically displayed in terms of the decontamination factor achieved at selected levels of conservatism versus pool depth and water subcooling or, in the case of sprays, versus time. (author)

  11. Chernobyl radiocesium in freshwater fish: Long-term dynamics and sources of variation

    Energy Technology Data Exchange (ETDEWEB)

    Sundbom, M [Uppsala Univ., Dept. of Limnology, Uppsala (Sweden)

    2002-04-01

    The aim of this thesis was to investigate both the long-term temporal pattern and sources of individual variation for radiocesium in freshwater fish. The basis for the study is time series of {sup 137}Cs activity concentrations in fish from three lakes in the area North-west of Uppsala, Sweden that received considerable amounts of {sup 137}Cs from Chernobyl in may 1986. The lakes were Lake Ekholmssjoen, Lake Flatsjoen and Lake Siggeforasjoen, all small forest lakes, but with different morphometrical and chemical characteristics. The data were collected regularly, usually several times per year, during 1986-2000, using consistent methods. More than 7600 fish individuals from 7 species covering wide size ranges and feeding habits were analysed for {sup 137}Cs. For each fish was the length, weight, sex, and often the stomach contend recorded. The evaluation on long-term trends were based on data from all three lakes, while the study on sources of variation evaluated data from Lake Flatsjoen only. (au)

  12. Chernobyl radiocesium in freshwater fish: Long-term dynamics and sources of variation

    International Nuclear Information System (INIS)

    Sundbom, M.

    2002-01-01

    The aim of this thesis was to investigate both the long-term temporal pattern and sources of individual variation for radiocesium in freshwater fish. The basis for the study is time series of 137 Cs activity concentrations in fish from three lakes in the area North-west of Uppsala, Sweden that received considerable amounts of 137 Cs from Chernobyl in may 1986. The lakes were Lake Ekholmssjoen, Lake Flatsjoen and Lake Siggeforasjoen, all small forest lakes, but with different morphometrical and chemical characteristics. The data were collected regularly, usually several times per year, during 1986-2000, using consistent methods. More than 7600 fish individuals from 7 species covering wide size ranges and feeding habits were analysed for 137 Cs. For each fish was the length, weight, sex, and often the stomach contend recorded. The evaluation on long-term trends were based on data from all three lakes, while the study on sources of variation evaluated data from Lake Flatsjoen only. (au)

  13. Basic repository source term and data sheet report: Davis Canyon

    International Nuclear Information System (INIS)

    1988-01-01

    This report is one of series describing studies undertaken in support of the US Department of Energy Civilian Radioactive Waste Management (CRWM) Program. This study contains the derivation of values for environmental source terms and resources consumed for a CRWM repository. Estimates include heavy construction equipment; support equipment; shaft-sinking equipment; transportation equipment; and consumption of fuel, water electricity, and natural gas. Data are presented for construction and operation at an assumed site in Davis Canyon, Utah. 6 tabs

  14. Algorithms and analytical solutions for rapidly approximating long-term dispersion from line and area sources

    Science.gov (United States)

    Barrett, Steven R. H.; Britter, Rex E.

    Predicting long-term mean pollutant concentrations in the vicinity of airports, roads and other industrial sources are frequently of concern in regulatory and public health contexts. Many emissions are represented geometrically as ground-level line or area sources. Well developed modelling tools such as AERMOD and ADMS are able to model dispersion from finite (i.e. non-point) sources with considerable accuracy, drawing upon an up-to-date understanding of boundary layer behaviour. Due to mathematical difficulties associated with line and area sources, computationally expensive numerical integration schemes have been developed. For example, some models decompose area sources into a large number of line sources orthogonal to the mean wind direction, for which an analytical (Gaussian) solution exists. Models also employ a time-series approach, which involves computing mean pollutant concentrations for every hour over one or more years of meteorological data. This can give rise to computer runtimes of several days for assessment of a site. While this may be acceptable for assessment of a single industrial complex, airport, etc., this level of computational cost precludes national or international policy assessments at the level of detail available with dispersion modelling. In this paper, we extend previous work [S.R.H. Barrett, R.E. Britter, 2008. Development of algorithms and approximations for rapid operational air quality modelling. Atmospheric Environment 42 (2008) 8105-8111] to line and area sources. We introduce approximations which allow for the development of new analytical solutions for long-term mean dispersion from line and area sources, based on hypergeometric functions. We describe how these solutions can be parameterized from a single point source run from an existing advanced dispersion model, thereby accounting for all processes modelled in the more costly algorithms. The parameterization method combined with the analytical solutions for long-term mean

  15. Variational Iterative Refinement Source Term Estimation Algorithm Assessment for Rural and Urban Environments

    Science.gov (United States)

    Delle Monache, L.; Rodriguez, L. M.; Meech, S.; Hahn, D.; Betancourt, T.; Steinhoff, D.

    2016-12-01

    It is necessary to accurately estimate the initial source characteristics in the event of an accidental or intentional release of a Chemical, Biological, Radiological, or Nuclear (CBRN) agent into the atmosphere. The accurate estimation of the source characteristics are important because many times they are unknown and the Atmospheric Transport and Dispersion (AT&D) models rely heavily on these estimates to create hazard assessments. To correctly assess the source characteristics in an operational environment where time is critical, the National Center for Atmospheric Research (NCAR) has developed a Source Term Estimation (STE) method, known as the Variational Iterative Refinement STE algorithm (VIRSA). VIRSA consists of a combination of modeling systems. These systems include an AT&D model, its corresponding STE model, a Hybrid Lagrangian-Eulerian Plume Model (H-LEPM), and its mathematical adjoint model. In an operational scenario where we have information regarding the infrastructure of a city, the AT&D model used is the Urban Dispersion Model (UDM) and when using this model in VIRSA we refer to the system as uVIRSA. In all other scenarios where we do not have the city infrastructure information readily available, the AT&D model used is the Second-order Closure Integrated PUFF model (SCIPUFF) and the system is referred to as sVIRSA. VIRSA was originally developed using SCIPUFF 2.4 for the Defense Threat Reduction Agency and integrated into the Hazard Prediction and Assessment Capability and Joint Program for Information Systems Joint Effects Model. The results discussed here are the verification and validation of the upgraded system with SCIPUFF 3.0 and the newly implemented UDM capability. To verify uVIRSA and sVIRSA, synthetic concentration observation scenarios were created in urban and rural environments and the results of this verification are shown. Finally, we validate the STE performance of uVIRSA using scenarios from the Joint Urban 2003 (JU03

  16. Preliminary investigation of processes that affect source term identification

    International Nuclear Information System (INIS)

    Wickliff, D.S.; Solomon, D.K.; Farrow, N.D.

    1991-09-01

    Solid Waste Storage Area (SWSA) 5 is known to be a significant source of contaminants, especially tritium ( 3 H), to the White Oak Creek (WOC) watershed. For example, Solomon et al. (1991) estimated the total 3 H discharge in Melton Branch (most of which originates in SWSA 5) for the 1988 water year to be 1210 Ci. A critical issue for making decisions concerning remedial actions at SWSA 5 is knowing whether the annual contaminant discharge is increasing or decreasing. Because (1) the magnitude of the annual contaminant discharge is highly correlated to the amount of annual precipitation (Solomon et al., 1991) and (2) a significant lag may exist between the time of peak contaminant release from primary sources (i.e., waste trenches) and the time of peak discharge into streams, short-term stream monitoring by itself is not sufficient for predicting future contaminant discharges. In this study we use 3 H to examine the link between contaminant release from primary waste sources and contaminant discharge into streams. By understanding and quantifying subsurface transport processes, realistic predictions of future contaminant discharge, along with an evaluation of the effectiveness of remedial action alternatives, will be possible. The objectives of this study are (1) to characterize the subsurface movement of contaminants (primarily 3 H) with an emphasis on the effects of matrix diffusion; (2) to determine the relative strength of primary vs secondary sources; and (3) to establish a methodology capable of determining whether the 3 H discharge from SWSA 5 to streams is increasing or decreasing

  17. Development of dose calculation program (DBADOSE) incorporating alternative source term due to design basis accident

    International Nuclear Information System (INIS)

    Bae, Young Jig; Nam, Ki Mun; Lee, Yu Jong; Chung, Chan Young

    2003-01-01

    Source terms presented in TID-14844 and Regulatory Guide 1.4 have been used for radiological analysis of design basis accidents for licensing existing pressurized water reactor (PWR). However, more realistic and physically-based source term based on results of study and experiments for about 30 years after the publication of TID-14844 was developed and presented in NUREG-1465 published by U.S NRC in 1995. In addition, ICRP has revised dose concepts and criteria through the publication of ICRP-9, 26, 60 and recommended effective dose concepts rather than critical organ concept since the publication of ICRP-26. Accordingly, multipurpose computer program called DBADOSE incorporating alternative source terms in NUREG-1465 and effective dose concepts in ICRP-60 was developed. Comparison of results of DBADOSE with those of POSTDBA and STARDOSE was performed and verified and no significant difference and inaccuracy were found. DBADOSE will be used to evaluate accidental doses for licensing application according to the domestic laws that are expected to be revised in the near future

  18. Benchmarking the New RESRAD-OFFSITE Source Term Model with DUST-MS and GoldSim - 13377

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, J.J.; Kamboj, S.; Gnanapragasam, E.; Yu, C. [Argonne National Laboratory, Argonne, IL 60439 (United States)

    2013-07-01

    RESRAD-OFFSITE is a computer code developed by Argonne National Laboratory under the sponsorship of U.S. Department of Energy (DOE) and U.S. Nuclear Regulatory Commission (NRC). It is designed on the basis of RESRAD (onsite) code, a computer code designated by DOE and NRC for evaluating soil-contaminated sites for compliance with human health protection requirements pertaining to license termination or environmental remediation. RESRAD-OFFSITE has enhanced capabilities of modeling radionuclide transport to offsite locations and calculating potential radiation exposure to offsite receptors. Recently, a new source term model was incorporated into RESRAD-OFFSITE to enhance its capability further. This new source term model allows simulation of radionuclide releases from different waste forms, in addition to the soil sources originally considered in RESRAD (onsite) and RESRAD-OFFSITE codes. With this new source term model, a variety of applications can be achieved by using RESRAD-OFFSITE, including but not limited to, assessing the performance of radioactive waste disposal facilities. This paper presents the comparison of radionuclide release rates calculated by the new source term model of RESRAD-OFFSITE versus those calculated by DUST-MS and GoldSim, respectively. The focus of comparison is on the release rates of radionuclides from the bottom of the contaminated zone that was assumed to contain radioactive source materials buried in soil. The transport of released contaminants outside of the primary contaminated zone is beyond the scope of this paper. Overall, the agreement between the RESRAD-OFFSITE results and the DUST-MS and GoldSim results is fairly good, with all three codes predicting identical or similar radionuclide release profiles over time. Numerical dispersion in the DUST-MS and GoldSim results was identified as potentially contributing to the disagreement in the release rates. In general, greater discrepancy in the release rates was found for short

  19. Benchmarking the New RESRAD-OFFSITE Source Term Model with DUST-MS and GoldSim - 13377

    International Nuclear Information System (INIS)

    Cheng, J.J.; Kamboj, S.; Gnanapragasam, E.; Yu, C.

    2013-01-01

    RESRAD-OFFSITE is a computer code developed by Argonne National Laboratory under the sponsorship of U.S. Department of Energy (DOE) and U.S. Nuclear Regulatory Commission (NRC). It is designed on the basis of RESRAD (onsite) code, a computer code designated by DOE and NRC for evaluating soil-contaminated sites for compliance with human health protection requirements pertaining to license termination or environmental remediation. RESRAD-OFFSITE has enhanced capabilities of modeling radionuclide transport to offsite locations and calculating potential radiation exposure to offsite receptors. Recently, a new source term model was incorporated into RESRAD-OFFSITE to enhance its capability further. This new source term model allows simulation of radionuclide releases from different waste forms, in addition to the soil sources originally considered in RESRAD (onsite) and RESRAD-OFFSITE codes. With this new source term model, a variety of applications can be achieved by using RESRAD-OFFSITE, including but not limited to, assessing the performance of radioactive waste disposal facilities. This paper presents the comparison of radionuclide release rates calculated by the new source term model of RESRAD-OFFSITE versus those calculated by DUST-MS and GoldSim, respectively. The focus of comparison is on the release rates of radionuclides from the bottom of the contaminated zone that was assumed to contain radioactive source materials buried in soil. The transport of released contaminants outside of the primary contaminated zone is beyond the scope of this paper. Overall, the agreement between the RESRAD-OFFSITE results and the DUST-MS and GoldSim results is fairly good, with all three codes predicting identical or similar radionuclide release profiles over time. Numerical dispersion in the DUST-MS and GoldSim results was identified as potentially contributing to the disagreement in the release rates. In general, greater discrepancy in the release rates was found for short

  20. Source Term Characteristics Analysis for Structural Components in PWR spent fuel assembly

    Energy Technology Data Exchange (ETDEWEB)

    Kook, Dong Hak; Choi, Heui Joo; Cho, Dong Keun [KAERI, Daejeon (Korea, Republic of)

    2010-12-15

    Source terms of metal waste comprising a spent fuel assembly are relatively important when the spent fuel is pyroprocessed, because cesium, strontium, and transuranics are not a concern any more in the aspect of source term of permanent disposal. In this study, characteristics of radiation source terms for each structural component in spent fuel assembly was analyzed by using ORIGEN-S with a assumption that 10 metric tons of uranium is pyroprocessed. At first, mass and volume for each structural component of the fuel assembly were calculated in detail. Activation cross section library was generated by using KENO-VI/ORIGEN-S module for top-end piece and bottom-end piece, because those are located at outer core under different neutron spectrum compared to that of inner core. As a result, values of radioactivity, decay heat, and hazard index were reveled to be 1.32x1015 Bequerels, 238 Watts, 4.32x109 m3 water, respectively, at 10 years after discharge. Those values correspond to 0.6 %, 1.1 %, 0.1 %, respectively, compared to that of spent fuel. Inconel 718 grid plate was shown to be the most important component in the all aspects of radioactivity, decay heat, and hazard index although the mass occupies only 1 % of the total. It was also shown that if the Inconel 718 grid plate is managed separately, the radioactivity and hazard index of metal waste could be decreased to 25{approx}50 % and 35{approx}40 %, respectively. As a whole, decay heat of metal waste was shown to be negligible in the aspect of disposal system design, while the radioactivity and hazard index are important

  1. SOURCE TERM ESTIMATION BASED on PLANT STATUS and on GAMMA DOSE RATES Measured by an ON-line environmental Monitoring Network

    International Nuclear Information System (INIS)

    Stubna, M.; Bujan, A.; Duranova, T.

    1997-01-01

    A number of severe accident analyses for reactor unit with WWER-440 (213) has been performed in order to evaluate the source term and radiological consequences. As a tool for these analyses the WWER modified version of Source Term Code Package and Real Time Accident Release Consequences codes have been used. A set of emergency procedures - manuals for quick estimation of the source term and countermeasures introduction during early -pre-release phase of severe accident progression has been developed at Nuclear Power Plants Research Institute Trnava, Inc. These manuals are subdivided into three groups: 1.) evaluation of the barriers integrity, 2.) source term estimation and 3.) estimation of the distances for the countermeasures introduction. A methodology and computer module for interpretation of environmental data - source term assessment during post-release phase from on-line environmental network has been developed at Nuclear Power Plants Research Institute Trnava, Inc. The method is based on the conversion of measured dose rates to the source term,i.e. airborne radioactivity release rate, taking into account real meteorological data and location of the measure points. The bootstrap method for the estimation of the mean value of source term Q as integral value of the release and confidence interval of Q has been selected. The methodology of Q distribution into fission product groups according to code Real Time Accident Release Consequences needs is based on known plant status, i.e. on the results of pre calculated accident sequences. The paper describes the methodologies introduced above and the way of their application

  2. The Analytical Repository Source-Term (AREST) model: Description and documentation

    International Nuclear Information System (INIS)

    Liebetrau, A.M.; Apted, M.J.; Engel, D.W.; Altenhofen, M.K.; Strachan, D.M.; Reid, C.R.; Windisch, C.F.; Erikson, R.L.; Johnson, K.I.

    1987-10-01

    The geologic repository system consists of several components, one of which is the engineered barrier system. The engineered barrier system interfaces with natural barriers that constitute the setting of the repository. A model that simulates the releases from the engineered barrier system into the natural barriers of the geosphere, called a source-term model, is an important component of any model for assessing the overall performance of the geologic repository system. The Analytical Repository Source-Term (AREST) model being developed is one such model. This report describes the current state of development of the AREST model and the code in which the model is implemented. The AREST model consists of three component models and five process models that describe the post-emplacement environment of a waste package. All of these components are combined within a probabilistic framework. The component models are a waste package containment (WPC) model that simulates the corrosion and degradation processes which eventually result in waste package containment failure; a waste package release (WPR) model that calculates the rates of radionuclide release from the failed waste package; and an engineered system release (ESR) model that controls the flow of information among all AREST components and process models and combines release output from the WPR model with failure times from the WPC model to produce estimates of total release. 167 refs., 40 figs., 12 tabs

  3. Analysis of the source term in the Chernobyl-4 accident

    International Nuclear Information System (INIS)

    Alonso, A.; Lopez Montero, J.V.; Pinedo Garrido, P.

    1990-01-01

    The report presents the analysis of the Chernobyl accident and of the phenomena with major influence on the source term, including the chemical effects of materials dumped over the reactor, carried out by the Chair of Nuclear Technology at Madrid University under a contract with the CEC. It also includes the comparison of the ratio (Cs-137/Cs-134) between measurements performed by Soviet authorities and countries belonging to the Community and OECD area. Chapter II contains a summary of both isotope measurements (Cs-134 and Cs-137), and their ratios, in samples of air, water, soil and agricultural and animal products collected by the Soviets in their report presented in Vienna (1986). Chapter III reports on the inventories of cesium isotopes in the core, while Chapter IV analyses the transient, especially the fuel temperature reached, as a way to deduce the mechanisms which took place in the cesium escape. The cesium source term is analyzed in Chapter V. Normal conditions have been considered, as well as the transient and the post-accidental period, including the effects of deposited materials. The conclusion of this study is that Chernobyl accidental sequence is specific of the RBMK type of reactors, and that in the Western world, basic research on fuel behaviour for reactivity transients has already been carried out

  4. Dose assessments for Greifswald and Cadarache with new source terms from ITER NSSR-1

    International Nuclear Information System (INIS)

    Raskob, W.; Forschungszentrum Karlsruhe GmbH Technik und Umwelt; Hasemann, I.

    1997-08-01

    Probabilistic dose assessments for accidental atmospheric releases of various ITER source terms which contain tritium and/or activation products were performed for the sites of Greifswald, Germany, and Cadarache, France. No country specific rules were applied and the input parameters were adapted as far as possible to those used within former ITER studies to achieve a better comparability with site independent dose assessments performed in the frame of ITER. The calculations were based on source terms which, at the first time, contain a combination of tritium and activation products. This allowed a better judgement of the contribution of the individual fusion relevant materials to the total dose. The results were compared to site independent dose limits defined in the frame of ITER. Source terms for two different categories, representing 'extremely unlikely events' (CAT-IV) and 'hypothetical sequences' (CAT-V), were investigated. In no cases, the release scenarios of category CAT-IV exceeded the ITER limits. In addition, early doses from the hypothetical scenarios of type CAT-V were still below 50 mSv or 100 mSv, values which are commonly used as lower reference values for evacuation in many potential home countries of ITER. Only the banning of food products was found to be a potential countermeasure which may affect larger areas. (orig.) [de

  5. Source term calculations - Ringhals 2 PWR

    International Nuclear Information System (INIS)

    Johansson, L.L.

    1998-02-01

    This project was performed within the fifth and final phase of sub-project RAK-2.1 of the Nordic Co-operative Reactor Safety Program, NKS.RAK-2.1 has also included studies of reflooding of degraded core, recriticality and late phase melt progression. Earlier source term calculations for Swedish nuclear power plants are based on the integral code MAAP. A need was recognised to compare these calculations with calculations done with mechanistic codes. In the present work SCDAP/RELAP5 and CONTAIN were used. Only limited results could be obtained within the frame of RAK-2.1, since many problems were encountered using the SCDAP/RELAP5 code. The main obstacle was the extremely long execution times of the MOD3.1 version, but also some dubious fission product calculations. However, some interesting results were obtained for the studied sequence, a total loss of AC power. The report describes the modelling approach for SCDAP/RELAP5 and CONTAIN, and discusses results for the transient including the event of a surge line creep rupture. The study will probably be completed later, providing that an improved SCDAP/RELAP5 code version becomes available. (au) becomes available. (au)

  6. Basic repository source term and data sheet report: Lavender Canyon

    International Nuclear Information System (INIS)

    1988-01-01

    This report is one of a series describing studies undertaken in support of the US Department of Energy Civilian Radioactive Waste Management (CRWM) Program. This study contains the derivation of values for environmental source terms and resources consumed for a CRWM repository. Estimates include heavy construction equipment; support equipment; shaft-sinking equipment; transportation equipment; and consumption of fuel, water, electricity, and natural gas. Data are presented for construction and operation at an assumed site in Lavender Canyon, Utah. 3 refs; 6 tabs

  7. Emergency preparedness source term development for the Office of Nuclear Material Safety and Safeguards-Licensed Facilities

    International Nuclear Information System (INIS)

    Sutter, S.L.; Mishima, J.; Ballinger, M.Y.; Lindsey, C.G.

    1984-08-01

    In order to establish requirements for emergency preparedness plans at facilities licensed by the Office of Nuclear Materials Safety and Safeguards, the Nuclear Regulatory Commission (NRC) needs to develop source terms (the amount of material made airborne) in accidents. These source terms are used to estimate the potential public doses from the events, which, in turn, will be used to judge whether emergency preparedness plans are needed for a particular type of facility. Pacific Northwest Laboratory is providing the NRC with source terms by developing several accident scenarios for eleven types of fuel cycle and by-product operations. Several scenarios are developed for each operation, leading to the identification of the maximum release considered for emergency preparedness planning (MREPP) scenario. The MREPP scenarios postulated were of three types: fire, tornado, and criticality. Fire was significant at oxide fuel fabrication, UF 6 production, radiopharmaceutical manufacturing, radiopharmacy, sealed source manufacturing, waste warehousing, and university research and development facilities. Tornadoes were MREPP events for uranium mills and plutonium contaminated facilities, and criticalities were significant at nonoxide fuel fabrication and nuclear research and development facilities. Techniques for adjusting the MREPP release to different facilities are also described

  8. Environmental radiation safety: source term modification by soil aerosols. Interim report

    International Nuclear Information System (INIS)

    Moss, O.R.; Allen, M.D.; Rossignol, E.J.; Cannon, W.C.

    1980-08-01

    The goal of this project is to provide information useful in estimating hazards related to the use of a pure refractory oxide of 238 Pu as a power source in some of the space vehicles to be launched during the next few years. Although the sources are designed and built to withstand re-entry into the earth's atmosphere, and to impact with the earth's surface without releasing any plutonium, the possibility that such an event might produce aerosols composed of soil and 238 PuO 2 cannot be absolutely excluded. This report presents the results of our most recent efforts to measure the degree to which the plutonium aerosol source term might be modified in a terrestrial environment. The five experiments described represent our best effort to use the original experimental design to study the change in the size distribution and concentration of a 238 PuO 2 aerosol due to coagulation with an aerosol of clay or sandy loam soil

  9. Standardization of iridium-192 coiled source in terms of air kerma output

    Energy Technology Data Exchange (ETDEWEB)

    Shanta, A; Unnikrishnan, K; Tripathi, U B; Kannan, A; Iyer, P S [Bhabha Atomic Research Centre, Bombay (India)

    1996-08-01

    ICRU (1985) recommended that the output of gamma ray brachytherapy sources should be specified in terms of reference air kerma rate, defined as the kerma rate to air in air at a reference distance of 1 meter, perpendicular to the long axis of the source, corrected for air attenuation and scattering. As these measurements are difficult to carry out in the routine clinical use, it is the common practice to calibrate the re-entrant ionization chamber with respect to open air measurements and use the re-entrant chamber for routine measurements. This paper reports on the measurements carried out to correlate the nominal activity and air kerma rate of {sup 192}Ir wire sources supplied by the Board of Radiation and Isotope Technology, Department of Atomic Energy. (author). 3 refs, 1 tab.

  10. Standardization of iridium-192 coiled source in terms of air kerma output

    International Nuclear Information System (INIS)

    Shanta, A.; Unnikrishnan, K.; Tripathi, U.B.; Kannan, A.; Iyer, P.S.

    1996-01-01

    ICRU (1985) recommended that the output of gamma ray brachytherapy sources should be specified in terms of reference air kerma rate, defined as the kerma rate to air in air at a reference distance of 1 meter, perpendicular to the long axis of the source, corrected for air attenuation and scattering. As these measurements are difficult to carry out in the routine clinical use, it is the common practice to calibrate the re-entrant ionization chamber with respect to open air measurements and use the re-entrant chamber for routine measurements. This paper reports on the measurements carried out to correlate the nominal activity and air kerma rate of 192 Ir wire sources supplied by the Board of Radiation and Isotope Technology, Department of Atomic Energy. (author). 3 refs, 1 tab

  11. Long-term effects of radiation

    International Nuclear Information System (INIS)

    Smith, J.; Smith, T.

    1981-01-01

    It is pointed out that sources of long-term damage from radiation are two-fold. People who have been exposed to doses of radiation from initial early fallout but have recovered from the acute effects may still suffer long-term damage from their exposure. Those who have not been exposed to early fallout may be exposed to delayed fallout, the hazards from which are almost exclusively from ingesting strontium, caesium and carbon isotopes present in food; the damage caused is relatively unimportant compared with that caused by the brief doses from initial radiation and early fallout. A brief discussion is presented of the distribution of delayed long-lived isotope fallout, and an outline is sketched of late biological effects, such as malignant disease, cataracts, retarded development, infertility and genetic effects. (U.K.)

  12. Radioactivity source terms for underground engineering application

    Energy Technology Data Exchange (ETDEWEB)

    Tewes, H A [Lawrence Radiation Laboratory, Livermore, CA (United States)

    1969-07-01

    The constraints on nuclide production are usually very similar in any underground engineering application of nuclear explosives. However, in some applications the end product could be contaminated unless the proper nuclear device is used. This fact can be illustrated from two underground engineering experiments-Gasbuggy and Sloop. In the Gasbuggy experiment, appreciable tritium has been shown to be present in the gas currently being produced. However, in future gas stimulation applications (as distinct from experiments), a minimum production of tritium by the explosive is desirable since product contamination by this nuclide may place severe limitations on the use of the tritiated gas. In Sloop, where production of copper is the goal of the experiment, product contamination would not be caused by tritium but could result from other nuclides: Thus, gas stimulation could require the use of fission explosives while the lower cost per kiloton of thermonuclear explosives could make them attractive for ore-crushing applications. Because of this consideration, radionuclide production calculations must be made for both fission and for thermonuclear explosives in the underground environment. Such activation calculations materials of construction are performed in a manner similar to that described in another paper, but radionuclide production in the environment must be computed using both fission neutron and 14-MeV neutron sources in order to treat the 'source term' problem realistically. In making such computations, parameter studies including the effects of environmental temperature, neutron shielding, and rock types have been carried out. Results indicate the importance of carefully evaluating the radionuclide production for each individual underground engineering application. (author)

  13. Radioactivity source terms for underground engineering application

    International Nuclear Information System (INIS)

    Tewes, H.A.

    1969-01-01

    The constraints on nuclide production are usually very similar in any underground engineering application of nuclear explosives. However, in some applications the end product could be contaminated unless the proper nuclear device is used. This fact can be illustrated from two underground engineering experiments-Gasbuggy and Sloop. In the Gasbuggy experiment, appreciable tritium has been shown to be present in the gas currently being produced. However, in future gas stimulation applications (as distinct from experiments), a minimum production of tritium by the explosive is desirable since product contamination by this nuclide may place severe limitations on the use of the tritiated gas. In Sloop, where production of copper is the goal of the experiment, product contamination would not be caused by tritium but could result from other nuclides: Thus, gas stimulation could require the use of fission explosives while the lower cost per kiloton of thermonuclear explosives could make them attractive for ore-crushing applications. Because of this consideration, radionuclide production calculations must be made for both fission and for thermonuclear explosives in the underground environment. Such activation calculations materials of construction are performed in a manner similar to that described in another paper, but radionuclide production in the environment must be computed using both fission neutron and 14-MeV neutron sources in order to treat the 'source term' problem realistically. In making such computations, parameter studies including the effects of environmental temperature, neutron shielding, and rock types have been carried out. Results indicate the importance of carefully evaluating the radionuclide production for each individual underground engineering application. (author)

  14. Finite volume schemes with equilibrium type discretization of source terms for scalar conservation laws

    International Nuclear Information System (INIS)

    Botchorishvili, Ramaz; Pironneau, Olivier

    2003-01-01

    We develop here a new class of finite volume schemes on unstructured meshes for scalar conservation laws with stiff source terms. The schemes are of equilibrium type, hence with uniform bounds on approximate solutions, valid in cell entropy inequalities and exact for some equilibrium states. Convergence is investigated in the framework of kinetic schemes. Numerical tests show high computational efficiency and a significant advantage over standard cell centered discretization of source terms. Equilibrium type schemes produce accurate results even on test problems for which the standard approach fails. For some numerical tests they exhibit exponential type convergence rate. In two of our numerical tests an equilibrium type scheme with 441 nodes on a triangular mesh is more accurate than a standard scheme with 5000 2 grid points

  15. COMPASS: A source term code for investigating capillary barrier performance

    International Nuclear Information System (INIS)

    Zhou, Wei; Apted, J.J.

    1996-01-01

    A computer code COMPASS based on compartment model approach is developed to calculate the near-field source term of the High-Level-Waste repository under unsaturated conditions. COMPASS is applied to evaluate the expected performance of Richard's (capillary) barriers as backfills to divert infiltrating groundwater at Yucca Mountain. Comparing the release rates of four typical nuclides with and without the Richard's barrier, it is shown that the Richard's barrier significantly decreases the peak release rates from the Engineered-Barrier-System (EBS) into the host rock

  16. Development of computer-based function to estimate radioactive source term by coupling atmospheric model with monitoring data

    International Nuclear Information System (INIS)

    Akiko, Furuno; Hideyuki, Kitabata

    2003-01-01

    atmospheric dynamic equations. Meteorological fields are initialized by using numerical forecasts and/or analysis data from Japan Meteorological Agency. The horizontal and temporal resolutions of the data are 1.25 degree and 6 hours, respectively, and the data have 17 vertical layers. GEARN is a particle random walk model to calculate the atmospheric dispersion of radionuclides by tracing the trajectories of a large number of marker particles discharged from a source. Movement of marker particles in each time step is described by three basic processes: transport by three-dimensional mean winds, turbulence diffusion and deposition. Mean wind fields are provided from MM5 at the interval of 1 hour. The horizontal random movement by diffusion per time step δt is calculated as (6K hor δt) 0.5 * R, where R is a uniform random number between -1 and 1. The horizontal diffusion coefficient K hor is derived from the standard deviation of horizontal diffusion σ hor and the vertical diffusion coefficient is from MM5. The air concentration at each Eulerian grid cell is computed by summing up the number of marker particles in the grid cell. Atmospheric transport simulations are carried out for the matrix of possible release points in Eastern Asia and possible release times. Because the simulations for the matrix need much computation time, it is carried out by using parallel computer. The simulation results of air dose rates are compared with monitoring data by statistical analysis of normalized mean square error, and the best fitted release condition is chosen as source term. fig. 1 (author)

  17. Powering the Space Exploration Initiative

    International Nuclear Information System (INIS)

    Bennett, G.L.

    1991-01-01

    The Space Exploration Initiative (SEI) establishes the long-term goal of returning to the Moon and then exploring Mars. One of the prerequisites of SEI is the Exploration Technology Program which includes program elements on space nuclear power and surface solar power. These program elements in turn build upon the ongoing NASA research and technology base program in space energy conversion. There is a wide range of missions in NASA's strategic planning and most would benefit from power sources with improved efficiency, lighter weight and reduced cost

  18. On the application of subcell resolution to conservation laws with stiff source terms

    International Nuclear Information System (INIS)

    Chang, S.

    1989-11-01

    LeVeque and Yee recently investigated a one-dimensional scalar conservation law with stiff source terms modeling the reacting flow problems and discovered that for the very stiff case most of the current finite difference methods developed for non-reacting flows would produce wrong solutions when there is a propagating discontinuity. A numerical scheme, essentially nonoscillatory/subcell resolution - characteristic direction (ENO/SRCD), is proposed for solving conservation laws with stiff source terms. This scheme is a modification of Harten's ENO scheme with subcell resolution, ENO/SR. The locations of the discontinuities and the characteristic directions are essential in the design. Strang's time-splitting method is used and time evolutions are done by advancing along the characteristics. Numerical experiment using this scheme shows excellent results on the model problem of LeVeque and Yee. Comparisons of the results of ENO, ENO/SR, and ENO/SRCD are also presented

  19. A functional magnetic resonance imaging investigation of short-term source and item memory for negative pictures.

    Science.gov (United States)

    Mitchell, Karen J; Mather, Mara; Johnson, Marcia K; Raye, Carol L; Greene, Erich J

    2006-10-02

    We investigated the hypothesis that arousal recruits attention to item information, thereby disrupting working memory processes that help bind items to context. Using functional magnetic resonance imaging, we compared brain activity when participants remembered negative or neutral picture-location conjunctions (source memory) versus pictures only. Behaviorally, negative trials showed disruption of short-term source, but not picture, memory; long-term picture recognition memory was better for negative than for neutral pictures. Activity in areas involved in working memory and feature integration (precentral gyrus and its intersect with superior temporal gyrus) was attenuated on negative compared with neutral source trials relative to picture-only trials. Visual processing areas (middle occipital and lingual gyri) showed greater activity for negative than for neutral trials, especially on picture-only trials.

  20. The Manchester Fly Facility: Implementing an objective-driven long-term science communication initiative.

    Science.gov (United States)

    Patel, Sanjai; Prokop, Andreas

    2017-10-01

    Science communication is increasingly important for scientists, although research, teaching and administration activities tend to eat up our time already, and budgets for science communication are usually low. It appears impossible to combine all these tasks and, in addition, to develop engagement activities to a quality and impact that would make the efforts worth their while. Here we argue that these challenges are easier addressed when centering science communication initiatives on a long-term vision with a view to eventually forming outreach networks where the load can be shared whilst being driven to higher momentum. As one example, we explain the science communication initiative of the Manchester Fly Facility. It aims to promote public awareness of research using the model organism Drosophila, which is a timely, economic and most efficient experimental strategy to drive discovery processes in the biomedical sciences and must have a firm place in the portfolios of funding organisations. Although this initiative by the Manchester Fly Facility is sustained on a low budget, its long-term vision has allowed gradual development into a multifaceted initiative: (1) targeting university students via resources and strategies for the advanced training in fly genetics; (2) targeting the general public via science fairs, educational YouTube videos, school visits, teacher seminars and the droso4schools project; (3) disseminating and marketing strategies and resources to the public as well as fellow scientists via dedicated websites, blogs, journal articles, conference presentations and workshops - with a view to gradually forming networks of drosophilists that will have a greater potential to drive the science communication objective to momentum and impact. Here we explain the rationales and implementation strategies for our various science communication activities - which are similarly applicable to other model animals and other areas of academic science - and share our

  1. Quantification of uncertainties in source term estimates for a BWR with Mark I containment

    International Nuclear Information System (INIS)

    Khatib-Rahbar, M.; Cazzoli, E.; Davis, R.; Ishigami, T.; Lee, M.; Nourbakhsh, H.; Schmidt, E.; Unwin, S.

    1988-01-01

    A methodology for quantification and uncertainty analysis of source terms for severe accident in light water reactors (QUASAR) has been developed. The objectives of the QUASAR program are (1) to develop a framework for performing an uncertainty evaluation of the input parameters of the phenomenological models used in the Source Term Code Package (STCP), and (2) to quantify the uncertainties in certain phenomenological aspects of source terms (that are not modeled by STCP) using state-of-the-art methods. The QUASAR methodology consists of (1) screening sensitivity analysis, where the most sensitive input variables are selected for detailed uncertainty analysis, (2) uncertainty analysis, where probability density functions (PDFs) are established for the parameters identified by the screening stage and propagated through the codes to obtain PDFs for the outputs (i.e., release fractions to the environment), and (3) distribution sensitivity analysis, which is performed to determine the sensitivity of the output PDFs to the input PDFs. In this paper attention is limited to a single accident progression sequence, namely; a station blackout accident in a BWR with a Mark I containment buildings. Identified as an important accident in the draft NUREG-1150 a station blackout involves loss of both off-site power and DC power resulting in failure of the diesels to start and in the unavailability of the high pressure injection and core isolation coding systems

  2. Fluctuations of quasars and other astronomical sources: final report on New Research Initiatives Program W-210

    International Nuclear Information System (INIS)

    Terrell, J.

    1978-01-01

    New Research Initiatives Program W-210 produced a number of scientific results, publications, colloquia, and talks. Investigations under this program dealt with power spectra of fluctuating light sources, the apparent expansion rates of astronomical sources exploding at relativistic speed, the limits on fluctuation rates of such expanding (and nonexpanding) light sources, and related matters. Probably the most important result was a study of the time history of such an exploding light source, which showed that a widely held belief that unusually rapid fluctuations of light output would be produced in this case is not correct. This result has an important bearing on the interpretation of the redshifts of quasars and BL Lac objects, indicating that cosmological distance is very difficult to reconcile with the observations of rapid variations of luminosity. These results, and the power-spectrum results, are also of considerable interest in the study of astronomical x-ray sources. A list of publications is included

  3. PHENOstruct: Prediction of human phenotype ontology terms using heterogeneous data sources.

    Science.gov (United States)

    Kahanda, Indika; Funk, Christopher; Verspoor, Karin; Ben-Hur, Asa

    2015-01-01

    The human phenotype ontology (HPO) was recently developed as a standardized vocabulary for describing the phenotype abnormalities associated with human diseases. At present, only a small fraction of human protein coding genes have HPO annotations. But, researchers believe that a large portion of currently unannotated genes are related to disease phenotypes. Therefore, it is important to predict gene-HPO term associations using accurate computational methods. In this work we demonstrate the performance advantage of the structured SVM approach which was shown to be highly effective for Gene Ontology term prediction in comparison to several baseline methods. Furthermore, we highlight a collection of informative data sources suitable for the problem of predicting gene-HPO associations, including large scale literature mining data.

  4. Radioiodine source term and its potential impact on the use of potassium iodide

    International Nuclear Information System (INIS)

    Malinauskas, A.P.

    1982-01-01

    Information is presented concerning chemical forms of fission product iodine in the primary circuit; chemical forms of fission product iodine in the containment building; summary of iodine chemistry in light water reactor accidents; and impact of the radiodine source term on the potassium iodide issue

  5. The development of a realistic source term for sodium-cooled fast reactors : assessment of current status and future needs.

    Energy Technology Data Exchange (ETDEWEB)

    LaChance, Jeffrey L.; Phillips, Jesse; Parma, Edward J., Jr.; Olivier, Tara Jean; Middleton, Bobby D.

    2011-06-01

    Sodium-cooled fast reactors (SFRs) continue to be proposed and designed throughout the United States and the world. Although the number of SFRs actually operating has declined substantially since the 1980s, a significant interest in advancing these types of reactor systems remains. Of the many issues associated with the development and deployment of SFRs, one of high regulatory importance is the source term to be used in the siting of the reactor. A substantial amount of modeling and experimental work has been performed over the past four decades on accident analysis, sodium coolant behavior, and radionuclide release for SFRs. The objective of this report is to aid in determining the gaps and issues related to the development of a realistic, mechanistically derived source term for SFRs. This report will allow the reader to become familiar with the severe accident source term concept and gain a broad understanding of the current status of the models and experimental work. Further, this report will allow insight into future work, in terms of both model development and experimental validation, which is necessary in order to develop a realistic source term for SFRs.

  6. Inverse modeling of the Chernobyl source term using atmospheric concentration and deposition measurements

    Science.gov (United States)

    Evangeliou, Nikolaos; Hamburger, Thomas; Cozic, Anne; Balkanski, Yves; Stohl, Andreas

    2017-07-01

    This paper describes the results of an inverse modeling study for the determination of the source term of the radionuclides 134Cs, 137Cs and 131I released after the Chernobyl accident. The accident occurred on 26 April 1986 in the Former Soviet Union and released about 1019 Bq of radioactive materials that were transported as far away as the USA and Japan. Thereafter, several attempts to assess the magnitude of the emissions were made that were based on the knowledge of the core inventory and the levels of the spent fuel. More recently, when modeling tools were further developed, inverse modeling techniques were applied to the Chernobyl case for source term quantification. However, because radioactivity is a sensitive topic for the public and attracts a lot of attention, high-quality measurements, which are essential for inverse modeling, were not made available except for a few sparse activity concentration measurements far from the source and far from the main direction of the radioactive fallout. For the first time, we apply Bayesian inversion of the Chernobyl source term using not only activity concentrations but also deposition measurements from the most recent public data set. These observations refer to a data rescue attempt that started more than 10 years ago, with a final goal to provide available measurements to anyone interested. In regards to our inverse modeling results, emissions of 134Cs were estimated to be 80 PBq or 30-50 % higher than what was previously published. From the released amount of 134Cs, about 70 PBq were deposited all over Europe. Similar to 134Cs, emissions of 137Cs were estimated as 86 PBq, on the same order as previously reported results. Finally, 131I emissions of 1365 PBq were found, which are about 10 % less than the prior total releases. The inversion pushes the injection heights of the three radionuclides to higher altitudes (up to about 3 km) than previously assumed (≈ 2.2 km) in order to better match both concentration

  7. Inverse modeling of the Chernobyl source term using atmospheric concentration and deposition measurements

    Directory of Open Access Journals (Sweden)

    N. Evangeliou

    2017-07-01

    Full Text Available This paper describes the results of an inverse modeling study for the determination of the source term of the radionuclides 134Cs, 137Cs and 131I released after the Chernobyl accident. The accident occurred on 26 April 1986 in the Former Soviet Union and released about 1019 Bq of radioactive materials that were transported as far away as the USA and Japan. Thereafter, several attempts to assess the magnitude of the emissions were made that were based on the knowledge of the core inventory and the levels of the spent fuel. More recently, when modeling tools were further developed, inverse modeling techniques were applied to the Chernobyl case for source term quantification. However, because radioactivity is a sensitive topic for the public and attracts a lot of attention, high-quality measurements, which are essential for inverse modeling, were not made available except for a few sparse activity concentration measurements far from the source and far from the main direction of the radioactive fallout. For the first time, we apply Bayesian inversion of the Chernobyl source term using not only activity concentrations but also deposition measurements from the most recent public data set. These observations refer to a data rescue attempt that started more than 10 years ago, with a final goal to provide available measurements to anyone interested. In regards to our inverse modeling results, emissions of 134Cs were estimated to be 80 PBq or 30–50 % higher than what was previously published. From the released amount of 134Cs, about 70 PBq were deposited all over Europe. Similar to 134Cs, emissions of 137Cs were estimated as 86 PBq, on the same order as previously reported results. Finally, 131I emissions of 1365 PBq were found, which are about 10 % less than the prior total releases. The inversion pushes the injection heights of the three radionuclides to higher altitudes (up to about 3 km than previously assumed (≈ 2.2 km in order

  8. 40 CFR Table 6 to Subpart Xxxx of... - Initial Compliance With the Emission Limits for Tire Production Affected Sources

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Initial Compliance With the Emission Limits for Tire Production Affected Sources 6 Table 6 to Subpart XXXX of Part 63 Protection of... Pollutants: Rubber Tire Manufacturing Pt. 63, Subpt. XXXX, Table 6 Table 6 to Subpart XXXX of Part 63—Initial...

  9. A well-balanced scheme for Ten-Moment Gaussian closure equations with source term

    Science.gov (United States)

    Meena, Asha Kumari; Kumar, Harish

    2018-02-01

    In this article, we consider the Ten-Moment equations with source term, which occurs in many applications related to plasma flows. We present a well-balanced second-order finite volume scheme. The scheme is well-balanced for general equation of state, provided we can write the hydrostatic solution as a function of the space variables. This is achieved by combining hydrostatic reconstruction with contact preserving, consistent numerical flux, and appropriate source discretization. Several numerical experiments are presented to demonstrate the well-balanced property and resulting accuracy of the proposed scheme.

  10. Review of the status of validation of the computer codes used in the severe accident source term reassessment study (BMI-2104)

    International Nuclear Information System (INIS)

    Kress, T.S.

    1985-04-01

    The determination of severe accident source terms must, by necessity it seems, rely heavily on the use of complex computer codes. Source term acceptability, therefore, rests on the assessed validity of such codes. Consequently, one element of NRC's recent efforts to reassess LWR severe accident source terms is to provide a review of the status of validation of the computer codes used in the reassessment. The results of this review is the subject of this document. The separate review documents compiled in this report were used as a resource along with the results of the BMI-2104 study by BCL and the QUEST study by SNL to arrive at a more-or-less independent appraisal of the status of source term modeling at this time

  11. The Multimedia Environmental Pollutant Assessment System (MEPAS)reg-sign: Source-term release formulations

    International Nuclear Information System (INIS)

    Streile, G.P.; Shields, K.D.; Stroh, J.L.; Bagaasen, L.M.; Whelan, G.; McDonald, J.P.; Droppo, J.G.; Buck, J.W.

    1996-11-01

    This report is one of a series of reports that document the mathematical models in the Multimedia Environmental Pollutant Assessment System (MEPAS). Developed by Pacific Northwest National Laboratory for the US Department of Energy, MEPAS is an integrated impact assessment software implementation of physics-based fate and transport models in air, soil, and water media. Outputs are estimates of exposures and health risk assessments for radioactive and hazardous pollutants. Each of the MEPAS formulation documents covers a major MEPAS component such as source-term, atmospheric, vadose zone/groundwater, surface water, and health exposure/health impact assessment. Other MEPAS documentation reports cover the sensitivity/uncertainty formulations and the database parameter constituent property estimation methods. The pollutant source-term release component is documented in this report. MEPAS simulates the release of contaminants from a source, transport through the air, groundwater, surface water, or overland pathways, and transfer through food chains and exposure pathways to the exposed individual or population. For human health impacts, risks are computed for carcinogens and hazard quotients for noncarcinogens. MEPAS is implemented on a desktop computer with a user-friendly interface that allows the user to define the problem, input the required data, and execute the appropriate models for both deterministic and probabilistic analyses

  12. Influence of iodine chemistry on source term assessment

    International Nuclear Information System (INIS)

    Herranz Puebla, L. E.; Lopez Diez, I.; Rodriguez Maroto, J. J.; Martinez Lopez-Alcorocho, A.

    1991-01-01

    The major goal of a phenomenology analysis of containment during a severe accident situation can be spitted into the following ones: to know the containment response to the different loads and to predict accurately the fission product and aerosol behavior. In this report, the main results coming from the study of a hypothetical accident scenario, based on LA-4 experiment of LACE project, are presented. In order to do it, several codes have been coupled: CONTEMPT4/MOD5 (thermohydraulics), NAUA/MOD5 (aerosol physics) and IODE (iodine chemistry). It has been demonstrated the impossibility of assessing with confidence the Source Term if the chemical conduct of some radionuclides is not taken into account. In particular, the influence on the iodine retention efficiency of the sump of variables such as pH has been proven. (Author)12 refs

  13. Source term assessment using inverse modeling of radiation dose measured with environmental radiation monitors located at different positions

    International Nuclear Information System (INIS)

    Srinivas, C.V.; Rakesh, P.T.; Baskaran, R.; Venkatraman, B.

    2018-01-01

    Source term is an important input for consequence analysis using Decision Support Systems (DSS) to project radiological impact in the event of nuclear emergencies. A source term model called 'ASTER' is incorporated in the Online Nuclear Emergency Response System (ONERS) operational at Kalpakkam site for decision making during nuclear emergencies. This computes release rates using inverse method by employing an atmospheric dispersion model and gamma dose rates measured by environmental radiation monitors (ERM) deployed around the nuclear plant. The estimates may depend on the distribution of ERMs around the release location. In this work, data from various gamma monitors located at different radii 0.75 km and 1.5 km is used to assess the accuracy in the source term estimation for stack releases of MAPS-PHWR at Kalpakkam

  14. Final report of the inter institutional project ININ-CNSNS 'Source Terms specific for the CNLV'

    International Nuclear Information System (INIS)

    Anaya M, R.A.

    1991-02-01

    The purpose of the project inter institutional ININ-CNSNS 'Source Terms Specifies for the CNLV' it is the one of implanting in the computer CYBER (CDC 180-830) of the ININ, the 'Source Term Code Package' (STCP) and to make the operation tests and corresponding operation using the data of the sample problem, for finally to liberate the package, all time that by means of the analysis of the results it is consider appropriate. In this report the results of the are presented simulation of the sequence 'Energy Losses external' (Station blackout) and 'Lost total of CA with failure of the RCIC and success of the HPCS' both with data of the Laguna Verde Central. (Author)

  15. ORIGAMI Automator Primer. Automated ORIGEN Source Terms and Spent Fuel Storage Pool Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Wieselquist, William A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Thompson, Adam B. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bowman, Stephen M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Peterson, Joshua L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2016-04-01

    Source terms and spent nuclear fuel (SNF) storage pool decay heat load analyses for operating nuclear power plants require a large number of Oak Ridge Isotope Generation and Depletion (ORIGEN) calculations. SNF source term calculations also require a significant amount of bookkeeping to track quantities such as core and assembly operating histories, spent fuel pool (SFP) residence times, heavy metal masses, and enrichments. The ORIGEN Assembly Isotopics (ORIGAMI) module in the SCALE code system provides a simple scheme for entering these data. However, given the large scope of the analysis, extensive scripting is necessary to convert formats and process data to create thousands of ORIGAMI input files (one per assembly) and to process the results into formats readily usable by follow-on analysis tools. This primer describes a project within the SCALE Fulcrum graphical user interface (GUI) called ORIGAMI Automator that was developed to automate the scripting and bookkeeping in large-scale source term analyses. The ORIGAMI Automator enables the analyst to (1) easily create, view, and edit the reactor site and assembly information, (2) automatically create and run ORIGAMI inputs, and (3) analyze the results from ORIGAMI. ORIGAMI Automator uses the standard ORIGEN binary concentrations files produced by ORIGAMI, with concentrations available at all time points in each assembly’s life. The GUI plots results such as mass, concentration, activity, and decay heat using a powerful new ORIGEN Post-Processing Utility for SCALE (OPUS) GUI component. This document includes a description and user guide for the GUI, a step-by-step tutorial for a simplified scenario, and appendices that document the file structures used.

  16. Analysis of the Variability of Classified and Unclassified Radiological Source term Inventories in the Frenchman Flat Area, Nevada test Site

    International Nuclear Information System (INIS)

    Zhao, P.; Zavarin, M.

    2008-01-01

    It has been proposed that unclassified source terms used in the reactive transport modeling investigations at NTS CAUs should be based on yield-weighted source terms calculated using the average source term from Bowen et al. (2001) and the unclassified announced yields reported in DOE/NV-209. This unclassified inventory is likely to be used in unclassified contaminant boundary calculations and is, thus, relevant to compare to the classified inventory. They have examined the classified radionuclide inventory produced by 10 underground nuclear tests conducted in the Frenchman Flat (FF) area of the Nevada Test Site. The goals were to (1) evaluate the variability in classified radiological source terms among the 10 tests and (2) compare that variability and inventory uncertainties to an average unclassified inventory (e.g. Bowen 2001). To evaluate source term variability among the 10 tests, radiological inventories were compared on two relative scales: geometric mean and yield-weighted geometric mean. Furthermore, radiological inventories were either decay corrected to a common date (9/23/1992) or the time zero (t 0 ) of each test. Thus, a total of four data sets were produced. The date of 9/23/1992 was chosen based on the date of the last underground nuclear test at the Nevada Test Site

  17. Long-term trends in California mobile source emissions and ambient concentrations of black carbon and organic aerosol.

    Science.gov (United States)

    McDonald, Brian C; Goldstein, Allen H; Harley, Robert A

    2015-04-21

    A fuel-based approach is used to assess long-term trends (1970-2010) in mobile source emissions of black carbon (BC) and organic aerosol (OA, including both primary emissions and secondary formation). The main focus of this analysis is the Los Angeles Basin, where a long record of measurements is available to infer trends in ambient concentrations of BC and organic carbon (OC), with OC used here as a proxy for OA. Mobile source emissions and ambient concentrations have decreased similarly, reflecting the importance of on- and off-road engines as sources of BC and OA in urban areas. In 1970, the on-road sector accounted for ∼90% of total mobile source emissions of BC and OA (primary + secondary). Over time, as on-road engine emissions have been controlled, the relative importance of off-road sources has grown. By 2010, off-road engines were estimated to account for 37 ± 20% and 45 ± 16% of total mobile source contributions to BC and OA, respectively, in the Los Angeles area. This study highlights both the success of efforts to control on-road emission sources, and the importance of considering off-road engine and other VOC source contributions when assessing long-term emission and ambient air quality trends.

  18. Source term development for tritium at the Sheffield disposal site

    International Nuclear Information System (INIS)

    MacKenzie, D.R.; Barletta, R.E.; Smalley, J.F.; Kempf, C.R.; Davis, R.E.

    1984-01-01

    The Sheffield low-level radioactive waste disposal site, which ceased operation in 1978, has been the focus of modeling efforts by the NRC for the purpose of predicting long-term site behavior. To provide the NRC with the information required for its modeling effort, a study to define the source term for tritium in eight trenches at the Sheffield site has been undertaken. Tritium is of special interest since significant concentrations of the isotope have been found in groundwater samples taken at the site and at locations outside the site boundary. Previous estimates of tritium site inventory at Sheffield are in wide disagreement. In this study, the tritium inventory in the eight trenches was estimated by reviewing the radioactive shipping records (RSRs) for waste buried in these trenches. It has been found that the tritium shipped for burial at the site was probably higher than previously estimated. In the eight trenches surveyed, which amount to roughly one half the total volume and activity buried at Sheffield, approximately 2350 Ci of tritium from non-fuel cycle sources were identified. The review of RSRs also formed the basis for obtaining waste package descriptions and for contacting large waste generators to obtain more detailed information regarding these waste packages. As a result of this review and the selected generator contacts, the non-fuel cycle tritium waste was categorized. The tritium releases from each of these waste categories were modeled. The results of this modeling effort are presented for each of the eight trenches selected. 3 references, 2 figures

  19. Global threat reduction initiative efforts to address transportation challenges associated with the recovery of disused radioactive sealed sources - 10460

    International Nuclear Information System (INIS)

    Whitworth, Julie; Abeyta, Cristy L.; Griffin, Justin M.; Matzke, James L.; Pearson, Michael W.; Cuthbertson, Abigail; Rawl, Richard; Singley, Paul

    2010-01-01

    Proper disposition of disused radioactive sources is essential for their safe and secure management and necessary to preclude their use in malicious activities. Without affordable, timely transportation options, disused sealed sources remain in storage at hundreds of sites throughout the country and around the world. While secure storage is a temporary measure, the longer sources remain disused or unwanted the chances increase that they will become unsecured or abandoned. The Global Threat Reduction Initiative's Off-Site Source Recovery Project (GTRIlOSRP), recovers thousands of disused and unwanted sealed sources annually as part of GTRl's larger mission to reduce and protect high risk nuclear and radiological materials located at civilian sites worldwide. Faced with decreasing availability of certified transportation containers to support movement of disused and unwanted neutron- and beta/gamma-emitting radioactive sealed sources, GTRIlOSRP has initiated actions to ensure the continued success of the project in timely recovery and management of sealed radioactive sources. Efforts described in this paper to enhance transportation capabilities include: (sm b ullet) Addition of authorized content to existing and planned Type B containers to support the movement of non-special form and other Type B-quantity sealed sources; (sm b ullet) Procurement of vendor services for the design, development, testing and certification of a new Type B container to support transportation of irradiators, teletherapy heads or sources removed from these devices using remote handling capabilities such as the IAEA portable hot cell facility; (sm b ullet) Expansion of shielded Type A container inventory for transportation of gamma-emitting sources in activity ranges requiring use of shielding for conformity with transportation requirements; (sm b ullet) Approval of the S300 Type A fissile container for transport of Pu-239 sealed sources internationally; (sm b ullet) Technology transfer of

  20. Projected Source Terms for Potential Sabotage Events Related to Spent Fuel Shipments

    International Nuclear Information System (INIS)

    Luna, R.E.; Neuhauser, K.S.; Vigil, M.G.

    1999-01-01

    Two major studies, one sponsored by the U.S. Department of Energy and the other by the U.S. Nuclear Regulatory Commission, were conducted in the late 1970s and early 1980s to provide information and source terms for an optimally successful act of sabotage on spent fuel casks typical of those available for use. This report applies the results of those studies and additional analysis to derive potential source terms for certain classes of sabotage events on spent fuel casks and spent fuel typical of those which could be shipped in the early decades of the 21st century. In addition to updating the cask and spent fuel characteristics used in the analysis, two release mechanisms not included in the earlier works were identified and evaluated. As would be expected, inclusion of these additional release mechanisms resulted in a somewhat higher total release from the postulated sabotage events. Although health effects from estimated releases were addressed in the earlier study conducted for U.S. Department of Energy, they have not been addressed in this report. The results from this report maybe used to estimate health effects

  1. Basic repository source term and data sheet report: Deaf Smith County

    International Nuclear Information System (INIS)

    1987-01-01

    This report is one of a series describing studies undertaken in support of the US Department of Energy Civilian Radioactive Waste Management (CRWM) Program. This study contains the derivation of values for environmental source terms and resources consumed for a CRWM repository. Estimates include heavy construction equipment; support equipment; shaft-sinking equipment; transportation equipment; and consumption of fuel, water, electricity, and natural gas. Data are presented for construction and operation at an assumed site in Deaf Smith County, Texas. 2 refs., 6 tabs

  2. Design parameters and source terms: Volume 1, Design parameters: Revision 0

    International Nuclear Information System (INIS)

    1987-09-01

    The Design Parameters and Source Terms Document was prepared in accordance with DOE request and to provide data for the environmental impact study to be performed in the future for the Deaf Smith County, Texas site for a nuclear waste repository in salt. This document updates a previous unpublished report to the level of the Site Characterization Plan - Conceptual Design Report, SCP-CDR. The previous unpublished SCC Study identified the data needs for the Environmental Assessment effort for seven possible salt repository sites

  3. New source terms: what do they tell us about engineered safety feature performance

    International Nuclear Information System (INIS)

    Bernero, R.M.

    1985-01-01

    The accident behavior models which are the basis of engineered safety feature design are generally simple, non-mechanistic and concentrated on volatile radioiodine. Now data from source term studies show that models should be more mechanistic and look at other species than volatile iodine. A complete reevaluation of engineered safety features is needed

  4. Dose assessments for Greifswald and Cadarache with updated source terms from ITER NSSR-2

    International Nuclear Information System (INIS)

    Raskob, W.; Hasemann, I.

    1998-08-01

    The International Thermonuclear Experimental Reactor ITER is in its late engineering phase. One of the most important safety aspects - in particular for achieving public acceptance - is to assure that the releases of harzardous material are minimal during normal operation and for accidental events, even if very unlikely. To this purpose probabilistic dose assessments for accidental atmospheric releases of various ITER source terms which contain tritium and/or activation products were performed for the sites of Greifswald, Germany, and Cadarache, France. In addition, routine releases into the atmosphere and hydrosphere have been evaluated. No country specific rules were applied and the input parameters were adapted as far as possible to those used within former studies to achieve a better comparability with site independent dose assessments performed in the frame of ITER. The calculations were based on source terms which, for the first time, contain a combination of tritium and activation products. This allowed a better judgment of the contribution to the total dose of the individual fusion relevant materials. The results were compared to site independent dose limits defined in the frame of ITER. Annual doses from routine releases (CAT-I) are below 0.1 μSv for the aquatic scenarios and are close to 1 μSv for the atmospheric source terms. Source terms for two different categories of accidental releases, representing 'extremely unlikely events' (CAT-IV) and 'hypothetical sequences' (CAT-V), were investigated. In none of these cases, the release scenarios of category CAT-IV exceed the ITER limits. In addition, relevant characteristic quantities of the early dose distribution from the hypothetical scenarios of type CAT-V are still below 50 mSv or 100 mSv, values which are commonly used as lower reference values for evacuation in many potential home countries of ITER. These site specific assessments confirmed that the proposed release limits and thus the derived dose

  5. Restoration of the covariant gauge α in the initial field of gravity in de Sitter spacetime

    Energy Technology Data Exchange (ETDEWEB)

    Cheong, Lee Yen; Yan, Chew Xiao [Department of Fundamental and Applied Sciences, Universiti Teknologi Petronas, Bandar Seri Iskandar, Tronoh 31750, Perak (Malaysia)

    2014-03-05

    The gravitational field generated by a mass term and the initial surface through covariant retarded Green's function for linearized gravity in de Sitter spacetime was studied recently [4, 5] with the covariant gauges set to β = 2/3 and α = 5/3. In this paper we extend the work to restore the gauge parameter α in the field coming from the initial data using the method of shifting the parameter. The α terms in the initial field cancels exactly with the one coming from the source term. Consequently, the correct field configuration, with two equal mass points moving in its geodesic, one located at the North pole and another one located at the South pole, is reproduced in the whole manifold of de Sitter spacetime.

  6. 40 CFR Table 7 to Subpart Xxxx of... - Initial Compliance With the Emission Limits for Tire Cord Production Affected Sources

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Initial Compliance With the Emission Limits for Tire Cord Production Affected Sources 7 Table 7 to Subpart XXXX of Part 63 Protection of... Pollutants: Rubber Tire Manufacturing Pt. 63, Subpt. XXXX, Table 7 Table 7 to Subpart XXXX of Part 63—Initial...

  7. MIT/OSO 7 catalog of x-ray sources: intensities, spectra, and long-term variability

    International Nuclear Information System (INIS)

    Markert, T.H.; Winkler, P.F.; Laird, F.N.; Clark, G.W.; Hearn, D.R.; Sprott, G.F.; Li, F.K.; Bradt, H.V.; Lewin, W.H.G.; Schnopper, H.W.

    1979-01-01

    This paper is a summary of the observations of the cosmic X-ray sky performed by the MIT 1--40 KeV X-ray detectors on the OSO 7 between 1971 October and 1973 May. Specifically, we have computed the mean intensities or upper limits of all third Uhuru or OSO 7 cataloged sources (185 sources) in the 3--10 KeV range. For those sources for which a statistically significant (>20) intensity was found in the 3--10 KeV band (138 sources), further intensity determinations were made in the 1--15 KeV, 1--6 KeV, and 15--40 KeV energy bands. We have provided graphs and other simple techniques to aid the user in converting the observed counting rates to convenient units and in determining spectral parameters. Finally, we have plotted long-term light curves (counting rates in one or more energy bands as a function of time) for 86 of the brighter sources

  8. Source term and behavioural parameters for a postulated HIFAR loss-of-coolant accident

    International Nuclear Information System (INIS)

    May, F.G.

    1987-01-01

    The fraction of the fission product inventory which might be released into the atmosphere of the HIFAR reactor containment building (RCB) during a postulated loss-of-coolant accident (LOCA) has been evaluated as a function of time, for each classification of airborne radioactivity. This appraisal will be used as the source term for a computer program, which uses realistic attenuation of the fission product aerosol in a single compartment model with a defined leakrate to predict possible radioactive releases into the environment in a hypothetical bounding case reactor accident which is rather more severe in all major aspects than any single LOCA. Also given are the parameters governing the attenuation of the aerosol and vapours in the atmosphere of the RCB so that their behaviour may be accurately modelled. The source terms for several other types of accident involving the meltdown of fuel elements have also been considered but in less detail than the LOCA case. In some of the cases, the fission products are released directly to atmosphere, so there is no attenuation of the release by deposition within the RCB

  9. Effects of Heterogeneity and Uncertainties in Sources and Initial and Boundary Conditions on Spatiotemporal Variations of Groundwater Levels

    Science.gov (United States)

    Zhang, Y. K.; Liang, X.

    2014-12-01

    Effects of aquifer heterogeneity and uncertainties in source/sink, and initial and boundary conditions in a groundwater flow model on the spatiotemporal variations of groundwater level, h(x,t), were investigated. Analytical solutions for the variance and covariance of h(x, t) in an unconfined aquifer described by a linearized Boussinesq equation with a white noise source/sink and a random transmissivity field were derived. It was found that in a typical aquifer the error in h(x,t) in early time is mainly caused by the random initial condition and the error reduces as time goes to reach a constant error in later time. The duration during which the effect of the random initial condition is significant may last a few hundred days in most aquifers. The constant error in groundwater in later time is due to the combined effects of the uncertain source/sink and flux boundary: the closer to the flux boundary, the larger the error. The error caused by the uncertain head boundary is limited in a narrow zone near the boundary but it remains more or less constant over time. The effect of the heterogeneity is to increase the variation of groundwater level and the maximum effect occurs close to the constant head boundary because of the linear mean hydraulic gradient. The correlation of groundwater level decreases with temporal interval and spatial distance. In addition, the heterogeneity enhances the correlation of groundwater level, especially at larger time intervals and small spatial distances.

  10. Athletes' perceived use of information sources when forming initial impressions and expectancies of a coach: An explorative study

    OpenAIRE

    Manley, AJ; Greenlees, I; Graydon, J; Thelwell, R; Fllby, WCD; Smith, MJ

    2008-01-01

    The study aimed to identify the sources of information that athletes perceive as influential during their initial evaluation of coaching ability. University athletes (N = 538) were asked to indicate the influence of 31 informational cues (e.g., gender, body language or gestures, reputation) on the initial impression formed of a coach. Following exploratory factor analysis, a 3-factor model, (i.e., static cues, dynamic cues, and third-party reports) was extracted. Mean scores revealed that alt...

  11. Factors That Influence Breastfeeding Initiation Among African American Women.

    Science.gov (United States)

    Hinson, Tyonne D; Skinner, Asheley Cockrell; Lich, Kristen Hassmiller; Spatz, Diane L

    2018-05-01

    To examine cultural and socioenvironmental factors that affect breastfeeding initiation among African American women. Qualitative descriptive design and conventional content analysis. A large, inner-city, primary care center affiliated with a 500-bed children's hospital within a large, Northeastern U.S. city. Participants were 34 U.S.-born African American mothers of healthy term infants 0 to 3 months of age. Six focus groups were conducted using a 16-question, scripted interview guide. A number of complex factors that influenced breastfeeding initiation included certain cultural beliefs about sexuality, the influence of family and peer networks, information sources, intentions, and a variety of other barriers and facilitators. Our findings suggest that the decision to initiate breastfeeding is not solely determined by the woman within the African American community. Because this decision is contingent on multiple factors external to the woman, it is important to recognize the role that partners, grandmothers, communities, information sources, and health care providers/organizations play in women's decisions. Implementation of multilevel strategies is critical to increase breastfeeding initiation among African American mothers. Copyright © 2018 AWHONN, the Association of Women's Health, Obstetric and Neonatal Nurses. Published by Elsevier Inc. All rights reserved.

  12. Reciprocity relations and the mode conversion-absorption equation with an inhomogeneous source term

    International Nuclear Information System (INIS)

    Cho, S.; Swanson, D.G.

    1990-01-01

    The fourth-order mode conversion equation is solved completely via the Green's function to include an inhomogeneous source term. This Green's function itself contains all the plasma responsive effects such as mode conversion and absorption, and can be used to describe the spontaneous emission. In the course of the analysis, the reciprocity relations between coupling parameters are proved

  13. The EC CAST project (carbon-14 source term)

    International Nuclear Information System (INIS)

    Williams, S. J.

    2015-01-01

    Carbon-14 is a key radionuclide in the assessment of the safety of underground geological disposal facilities for radioactive wastes. It is possible for carbon-14 to be released from waste packages in a variety of chemical forms, both organic and inorganic, and as dissolved or gaseous species The EC CAST (CArbon-14 Source Term) project aims to develop understanding of the generation and release of carbon-14 from radioactive waste materials under conditions relevant to packaging and disposal. It focuses on the release of carbon-14 from irradiated metals (steels and zirconium alloys), from irradiated graphite and from spent ion-exchange resins. The CAST consortium brings together 33 partners. CAST commenced in October 2013 and this paper describes progress to March 2015. The main activities during this period were reviews of the current status of knowledge, the identification and acquisition of suitable samples and the design of experiments and analytical procedures. (authors)

  14. Mapping of the flux and estimate of the radiation source term of neutron fields generated by the GE PETtrace-8 cyclotron

    International Nuclear Information System (INIS)

    Benavente Castillo, Jhonny Antonio

    2017-01-01

    The use of spectrometric techniques in a cyclotron facility is strongly advised for the complete characterization of the neutron radiation field. In recent years, several studies of neutron spectrometry have been carried out at the Cyclotron of the Development Center of Nuclear Technology (CDTN). The main objective of this work is to propose a methodology for mapping of the flux and estimate of the radiation source term of neutron fields generated by the GE PETtrace-8 cyclotron. The method of neutron activation analysis with gold, indium and nickel activation foils was used to measure the activities induced at specific points in the cyclotron bunker. The irradiations of the activation foils were performed using the intermittent irradiation method to optimize the radiation field during 18 F production. The study of the neutron spectrum was performed using three radiation source terms. The first source term was constructed based on data provided by the cyclotron manufacturer using the neutron cross sections of the ENDF/B-VII library. The other two were proposed considering the irradiation process used in the routine of 18 F production. Both radiation source terms used the LA150H proton cross sections and for the 18 O, the cross sections of the physical model CEM03 (Cascade-exciton model) and TENDL (TALYS-based Evaluated Nuclear Data Library) were used. The results of the source terms in relation to the experimental results, in terms of neutron fluence rates, reaction rates and dose equivalent rates, showed that are in the same order of magnitude as those obtained by Ogata et al, Fujibuchi et al, and Gallerani et al., for the same cyclotron; and by Mendez et al. for a different manufacturing cyclotron. The models of the proposed radiation source terms were validated to obtain the spectra generated during the 18 F production when water enriched at 18 O is bombarded with a proton beam of 16.5 MeV. Finally, the model of the LA150H - TENDL - 2015 radiation source term is

  15. Short-term initiatives for enhancing cyber-safety within South African schools

    Directory of Open Access Journals (Sweden)

    Elmarie Kritzinger

    2016-07-01

    Full Text Available The rate of technological development across the globe is dramatic. The decreasing cost and increasing availability of ICT devices means that its users are no longer exclusively industry or government employees – they are now also home users. Home users integrate ICT in their daily lives for education, socialising and information gathering. However, using ICT is associated with risks and threats, such as identity theft and phishing scams. Most home users of ICT do not have the necessary information technology and Internet skills to protect themselves and their information. School learners, in particular, are not sufficiently educated on how to use technological devices safely, especially in developing countries such as South Africa. The national school curriculum in South Africa currently does not make provision for cyber-safety education, and the availability of supporting material and training for ICT teachers in South Africa is limited, resulting in a lack of knowledge and skills regarding cyber-safety. The research in hand focuses on the situation concerning cyber-safety awareness in schools and has adopted a short-term approach towards cyber-safety among teachers and school learners in South Africa until a formal long-term national approach has been implemented. This study takes a quantitative approach to investigating the current options of teachers to enhance cyber-safety among learners in their schools. The research proposes that short-term initiatives (i.e. posters can increase learners’ awareness of cyber-safety until formal cyber-safety awareness methods have been introduced.

  16. EFFECT OF NITROGEN SOURCE AND INITIAL SUGAR CONCENTRATION ON LACTIC ACID FERMENTATION OF PINEAPPLE WASTE USING L.DELBRUECKII

    Directory of Open Access Journals (Sweden)

    Abdullah Moch Busairi

    2012-02-01

    Full Text Available The liquid pineapple waste contains mainly sucrose, glucose, fructose and other nutrients. It therefore can potentially be used as carbon source for lactic acid fermentation. The lactic acid is utilised in food technology as pH regulator, microbial preservative, buffering agent and in the chemical industry. Recently, lactic acid has been considered to be an important raw material for production of biodegradable lactate polymer. The experiments were carried out in batch fermentation at anaerobic condition with stirring speed: 50 rpm, temperature: 40 oC, pH: 6.0, and inoculum size: 5%. Effect of nitrogen source and initial sugar concentration were studied. The effect of nitrogen source on lactic acid production shows that the yeast extract is highest yield , followed by urea , corn steep liquor, malt sprout and ammonium sulphates with the yield of 78.52; 26.68; 19.14; 14.10 and 5.6 %, respectively. The highest yield of initial sugar concentration on lactic acid production obtained was 78.52 % (54.97 g/l at 70 g/l, if the concentration of sugar was increased to 110 g/l , the lactic acid production or yield decrease to51.53 g/l or 54.24%.

  17. Does short-term virologic failure translate to clinical events in antiretroviral-naïve patients initiating antiretroviral therapy in clinical practice?

    DEFF Research Database (Denmark)

    NN, NN; Mugavero, Michael J; May, Margaret

    2008-01-01

    , nevirapine, lopinavir/ritonavir, nelfinavir, or abacavir as third drugs in combination with a zidovudine and lamivudine nucleoside reverse transcriptase inhibitor backbone. MAIN OUTCOME MEASURES: Short-term (24-week) virologic failure (>500 copies/ml) and clinical events within 2 years of ART initiation.......58-2.22), lopinavir/ritonavir (1.32, 95% CI = 1.12-1.57), nelfinavir (3.20, 95% CI = 2.74-3.74), and abacavir (2.13, 95% CI = 1.82-2.50). However, the rate of clinical events within 2 years of ART initiation appeared higher only with nevirapine (adjusted hazard ratio for composite outcome measure 1.27, 95% CI = 1......OBJECTIVE: To determine whether differences in short-term virologic failure among commonly used antiretroviral therapy (ART) regimens translate to differences in clinical events in antiretroviral-naïve patients initiating ART. DESIGN: Observational cohort study of patients initiating ART between...

  18. Performance evaluation of a permanent ring magnet based helicon plasma source for negative ion source research

    Science.gov (United States)

    Pandey, Arun; Bandyopadhyay, M.; Sudhir, Dass; Chakraborty, A.

    2017-10-01

    Helicon wave heated plasmas are much more efficient in terms of ionization per unit power consumed. A permanent magnet based compact helicon wave heated plasma source is developed in the Institute for Plasma Research, after carefully optimizing the geometry, the frequency of the RF power, and the magnetic field conditions. The HELicon Experiment for Negative ion-I source is the single driver helicon plasma source that is being studied for the development of a large sized, multi-driver negative hydrogen ion source. In this paper, the details about the single driver machine and the results from the characterization of the device are presented. A parametric study at different pressures and magnetic field values using a 13.56 MHz RF source has been carried out in argon plasma, as an initial step towards source characterization. A theoretical model is also presented for the particle and power balance in the plasma. The ambipolar diffusion process taking place in a magnetized helicon plasma is also discussed.

  19. Modification to ORIGEN2 for generating N Reactor source terms. Volume 1

    International Nuclear Information System (INIS)

    Schwarz, R.A.

    1997-04-01

    This report discusses work that has been done to upgrade the ORIGEN2 code cross sections to be compatible with the WIMS computer code data. Because of the changes in the ORIGEN2 calculations. Details on changes made to the ORIGEN2 computer code and the Radnuc code will be discussed along with additional work that should be done in the future to upgrade both ORIGEN2 and Radnuc. A detailed historical description of how source terms have been generated for N Reactor fuel stored in the K Basins has been generated. The neutron source discussed in this description was generated by the WIMS computer code (Gubbins et al. 1982) because of known shortcomings in the ORIGEN2 (Croff 1980) cross sections. Another document includes a discussion of the ORIGEN2 cross sections

  20. Function of a deltaic silt deposit as a repository and long-term source of sulfate and related weathering products in a glaciofluvial aquifer derived from organic-rich shale (North Dakota, USA)

    Science.gov (United States)

    Schuh, W. M.; Bottrell, S. H.

    2014-05-01

    A shallow unconfined glaciofluvial aquifer in North Dakota (USA) has largest groundwater sulfate concentrations near the bottom boundary. A deltaic silt layer underlying the aquifer, at >16 m, is the modern proximate sulfate source for the aquifer. The original sulfate source was pyrite in the organic-rich shale component of the aquifer and silt grain matrix. An oxidizing event occurred during which grain-matrix pyrite sulfur was oxidized to sulfate. Thereafter the silt served as a "conserving" layer, slowly feeding sulfate into the lower part of the aquifer and the underlying till. A method was developed for estimating the approximate initial sulfate concentration in the source layer and the redistribution time since the oxidizing event, using a semi-generic convection-dispersion model. The convection-dispersion model and a model for the evolution of modern sulfate δ 34S in silt-layer pore water from the initial grain-matrix pyrite δ 34S, both estimated that the oxidizing event occurred several thousand years ago, and was likely related to the dry conditions of the Hypsithermal Interval. The silt layer also serves as an arsenic source. Results indicate that deltaic silts derived from organic-rich shale parent materials in a glacial environment can provide long-term sources for sulfate and arsenic and possibly other related oxidative weathering products.

  1. Mid-term follow-up of whiplash with Bournemouth Questionnaire: the significance of the initial depression to pain ratio.

    Science.gov (United States)

    Griggs, R K L; Cook, J; Gargan, M; Bannister, G; Amirfeyz, R

    2015-01-01

    The Bournemouth Questionnaire (BQ) was used to report the short to mid-term outcome of a prospective cohort of patients who had sustained Whiplash Associated Disorder (WAD), and establish whether outcome could be predicted on initial assessment. One hundred patients with WAD grades I-III on the Quebec Task Force Classification were referred for physiotherapy (neck posture advice, initially practised under the direct supervision of a therapist). BQ scores were recorded on the first visit, at six weeks, then at final follow-up. Seventy-six percent of patients were available at final follow-up, 58% women. The mean age was 43.2 years old and follow-up time 38 months (28-48). Symptoms plateaued after six weeks in the majority and improved gradually thereafter. When the individual BQ components on initial presentation were reassessed, patients who score disproportionately highly in BQ Question 5 (Depression) had a worse outcome. To quantify this, the ratio of BQ Questions 5 (Depression)/1 (Pain) was calculated. BQ5/1 ratio greater than 1 on initial presentation had an odds ratio of 2 for poor outcome (p= 0.02). The BQ can therefore be used to identify patients with a disproportionately high depression score (BQ5) who are highly likely to clinically deteriorate in the medium term.

  2. Source Term Characterization for Structural Components in 17 x 17 KOFA Spent Fuel Assembly

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Dong Keun; Kook, Dong Hak; Choi, Heui Joo; Choi, Jong Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2010-12-15

    Source terms of metal waste comprising a spent fuel assembly are relatively important when the spent fuel is pyroprocessed, because cesium, strontium, and transuranics are not a concern any more in the aspect of source term of permanent disposal. In this study, characteristics of radiation source terms for each structural component in spent fuel assembly was analyzed by using ORIGEN-S with a assumption that 10 metric tons of uranium is pyroprocessed. At first, mass and volume for each structural component of the fuel assembly were calculated in detail. Activation cross section library was generated by using KENO-VI/ORIGEN-S module for top-end piece and bottom-end piece, because those are located at outer core with different neutron spectrum compared to that of inner core. As a result, values of radioactivity, decay heat, and hazard index were reveled to be 1.40 x 10{sup 15} Bequerels, 236 Watts, 4.34 x 10{sup 9} m{sup 3}-water, respectively, at 10 years after discharge. Those values correspond to 0.7 %, 1.1 %, 0.1 %, respectively, compared to that of spent fuel. Inconel 718 grid plate was shown to be the most important component in the all aspects of radioactivity, decay heat, and hazard index although the mass occupies only 1 % of the total. It was also shown that if the Inconel 718 grid plate is managed separately, the radioactivity and hazard index of metal waste could be decreased to 20 {approx} 45 % and 30 {approx} 45 %, respectively. As a whole, decay heat of metal waste was shown to be negligible in the aspect of disposal system design, while the radioactivity and hazard index are important.

  3. Does short-term virologic failure translate to clinical events in antiretroviral-naïve patients initiating antiretroviral therapy in clinical practice?

    NARCIS (Netherlands)

    Mugavero, Michael J; May, Margaret; Harris, Ross; Saag, Michael S; Costagliola, Dominique; Egger, Matthias; Phillips, Andrew; Günthard, Huldrych F; Dabis, Francois; Hogg, Robert; de Wolf, Frank; Fatkenheuer, Gerd; Gill, M John; Justice, Amy; D'Arminio Monforte, Antonella; Lampe, Fiona; Miró, Jose M; Staszewski, Schlomo; Sterne, Jonathan A C; Niesters, Bert

    2008-01-01

    OBJECTIVE: To determine whether differences in short-term virologic failure among commonly used antiretroviral therapy (ART) regimens translate to differences in clinical events in antiretroviral-naïve patients initiating ART. DESIGN: Observational cohort study of patients initiating ART between

  4. Health Care Expenditures After Initiating Long-term Services and Supports in the Community Versus in a Nursing Facility.

    Science.gov (United States)

    Newcomer, Robert J; Ko, Michelle; Kang, Taewoon; Harrington, Charlene; Hulett, Denis; Bindman, Andrew B

    2016-03-01

    Individuals who receive long-term services and supports (LTSS) are among the most costly participants in the Medicare and Medicaid programs. To compare health care expenditures among users of Medicaid home and community-based services (HCBS) versus those using extended nursing facility care. Retrospective cohort analysis of California dually eligible adult Medicaid and Medicare beneficiaries who initiated Medicaid LTSS, identified as HCBS or extended nursing facility care, in 2006 or 2007. Propensity score matching for demographic, health, and functional characteristics resulted in a subsample of 34,660 users who initiated Medicaid HCBS versus extended nursing facility use. Those with developmental disabilities or in managed care plans were excluded. Average monthly adjusted acute, postacute, long-term, and total Medicare and Medicaid expenditures for the 12 months following initiation of either HCBS or extended nursing facility care. Those initiating extended nursing facility care had, on average, $2919 higher adjusted total health care expenditures per month compared with those who initiated HCBS. The difference was primarily attributable to spending on LTSS $2855. On average, the monthly LTSS expenditures were higher for Medicare $1501 and for Medicaid $1344 when LTSS was provided in a nursing facility rather than in the community. The higher cost of delivering LTSS in a nursing facility rather than in the community was not offset by lower acute and postacute spending. Medicare and Medicaid contribute similar amounts to the LTSS cost difference and both could benefit financially by redirecting care from institutions to the community.

  5. Model description for calculating the source term of the Angra 1 environmental control system

    International Nuclear Information System (INIS)

    Oliveira, L.F.S. de; Amaral Neto, J.D.; Salles, M.R.

    1988-01-01

    This work presents the model used for evaluation of source term released from Angra 1 Nuclear Power Plant in case of an accident. After that, an application of the model for the case of a Fuel Assembly Drop Accident Inside the Fuel Handling Building during reactor refueling is presented. (author) [pt

  6. Calculation of the isotope concentrations, source terms and radiation shielding of the SAFARI-1 irradiation products

    International Nuclear Information System (INIS)

    Stoker, C.C.; Ball, G.

    2000-01-01

    The ever increasing expansion of the irradiation product portfolio of the SAFARI-1 reactor leads to the need to routinely calculate the radio-isotope concentrations and source terms for the materials irradiated in the reactor accurately. In addition to this, the required shielding for the transportation and processing of these irradiation products needs to be determined. In this paper the calculational methodology applied is described with special attention given to the spectrum dependence of the one-group cross sections of selected SAFARI-1 irradiation materials and the consequent effect on the determination of the isotope concentrations and source terms. Comparisons of the calculated isotopic concentrations and dose rates with experimental analysis and measurements provide confidence in the calculational methodologies and data used. (author)

  7. Tank waste source term inventory validation. Volume 1. Letter report

    International Nuclear Information System (INIS)

    Brevick, C.H.; Gaddis, L.A.; Johnson, E.D.

    1995-01-01

    The sample data for selection of 11 radionuclides and 24 chemical analytes were extracted from six separate sample data sets, were arranged in a tabular format and were plotted on scatter plots for all of the 149 single-shell tanks, the 24 double-shell tanks and the four aging waste tanks. The solid and liquid sample data was placed in separate tables and plots. The sample data and plots were compiled from the following data sets: characterization raw sample data, recent core samples, D. Braun data base, Wastren (Van Vleet) data base, TRAC and HTCE inventories. This document is Volume I of the Letter Report entitled Tank Waste Source Term Inventory Validation

  8. Regulatory Technology Development Plan - Sodium Fast Reactor. Mechanistic Source Term - Trial Calculation. Work Plan

    International Nuclear Information System (INIS)

    Grabaskas, David; Bucknor, Matthew; Jerden, James; Brunett, Acacia J.

    2016-01-01

    The overall objective of the SFR Regulatory Technology Development Plan (RTDP) effort is to identify and address potential impediments to the SFR regulatory licensing process. In FY14, an analysis by Argonne identified the development of an SFR-specific MST methodology as an existing licensing gap with high regulatory importance and a potentially long lead-time to closure. This work was followed by an initial examination of the current state-of-knowledge regarding SFR source term development (ANLART-3), which reported several potential gaps. Among these were the potential inadequacies of current computational tools to properly model and assess the transport and retention of radionuclides during a metal fuel pool-type SFR core damage incident. The objective of the current work is to determine the adequacy of existing computational tools, and the associated knowledge database, for the calculation of an SFR MST. To accomplish this task, a trial MST calculation will be performed using available computational tools to establish their limitations with regard to relevant radionuclide release/retention/transport phenomena. The application of existing modeling tools will provide a definitive test to assess their suitability for an SFR MST calculation, while also identifying potential gaps in the current knowledge base and providing insight into open issues regarding regulatory criteria/requirements. The findings of this analysis will assist in determining future research and development needs.

  9. Source term assessment, containment atmosphere control systems, and accident consequences. Report to CSNI by an OECD/NEA Group of experts

    International Nuclear Information System (INIS)

    1987-04-01

    CSNI Report 135 summarizes the results of the work performed by CSNI's Principal Working Group No. 4 on the Source Term and Environmental Consequences (PWG4) during the period extending from 1983 to 1986. This document contains the latest information on some important topics relating to source terms, accident consequence assessment, and containment atmospheric control systems. It consists of five parts: (1) a Foreword and Executive Summary prepared by PWG4's Chairman; (2) a Report on the Technical Status of the Source Term; (3) a Report on the Technical Status of Filtration and Containment Atmosphere Control Systems for Nuclear Reactors in the Event of a Severe Accident; (4) a Report on the Technical Status of Reactor Accident Consequence Assessment; (5) a list of members of PWG4

  10. A source term and risk calculations using level 2+PSA methodology

    International Nuclear Information System (INIS)

    Park, S. I.; Jea, M. S.; Jeon, K. D.

    2002-01-01

    The scope of Level 2+ PSA includes the assessment of dose risk which is associated with the exposures of the radioactive nuclides escaping from nuclear power plants during severe accidents. The establishment of data base for the exposure dose in Korea nuclear power plants may contribute to preparing the accident management programs and periodic safety reviews. In this study the ORIGEN, MELCOR and MACCS code were employed to produce a integrated framework to assess the radiation source term risk. The framework was applied to a reference plant. Using IPE results, the dose rate for the reference plant was calculated quantitatively

  11. Initial results with the Berkeley on-line mass separator-RAMA

    International Nuclear Information System (INIS)

    Cerny, J.; Moltz, D.M.; Evans, H.C.; Vieira, D.J.; Parry, R.F.; Wouters, J.M.; Gough, R.A.; Zisman, M.S.

    1977-11-01

    Initial performance is described for a reasonably fast and universal (having little or no chemical selectivity) on-line mass analysis system used to expand capabilities in studying nuclei far from stability. The system is termed RAMA, an acronym for Recoil Atom Mass Analyzer. Basically, this system utilizes the helium-jet method to transport activity to a Sidenius hollow-cathode ion source which is coupled to a mass spectrometer. Initial experiments and planned improvements are discussed. Transport efficiencies of between 10 and 60 percent have routinely been achieved, though the latter is much more typical when conditions are optimized

  12. Basic repository source term and data sheet report, Cypress Creek Dome: Draft

    International Nuclear Information System (INIS)

    1988-01-01

    This report is one of a series describing studies undertaken in support of the US Department of Energy Civilian Radioactive Waste Management (CRWM) Program. This study contains the derivation of values for environmental source terms and resources consumed for a CRWM repository. Estimates include heavy construction equipment; support equipment; shaft-sinking equipment; transportation equipment; and consumption of fuel, water, electricity, and natural gas. Data are presented for construction and operation at an assumed site in Cypress Creek Dome, Mississippi. 2 refs., 6 tabs

  13. Optimization method for identifying the source term in an inverse wave equation

    Directory of Open Access Journals (Sweden)

    Arumugam Deiveegan

    2017-08-01

    Full Text Available In this work, we investigate the inverse problem of identifying a space-wise dependent source term of wave equation from the measurement on the boundary. On the basis of the optimal control framework, the inverse problem is transformed into an optimization problem. The existence and necessary condition of the minimizer for the cost functional are obtained. The projected gradient method and two-parameter model function method are applied to the minimization problem and numerical results are illustrated.

  14. The MIT/OSO 7 catalog of X-ray sources - Intensities, spectra, and long-term variability

    Science.gov (United States)

    Markert, T. H.; Laird, F. N.; Clark, G. W.; Hearn, D. R.; Sprott, G. F.; Li, F. K.; Bradt, H. V.; Lewin, W. H. G.; Schnopper, H. W.; Winkler, P. F.

    1979-01-01

    This paper is a summary of the observations of the cosmic X-ray sky performed by the MIT 1-40-keV X-ray detectors on OSO 7 between October 1971 and May 1973. Specifically, mean intensities or upper limits of all third Uhuru or OSO 7 cataloged sources (185 sources) in the 3-10-keV range are computed. For those sources for which a statistically significant (greater than 20) intensity was found in the 3-10-keV band (138 sources), further intensity determinations were made in the 1-15-keV, 1-6-keV, and 15-40-keV energy bands. Graphs and other simple techniques are provided to aid the user in converting the observed counting rates to convenient units and in determining spectral parameters. Long-term light curves (counting rates in one or more energy bands as a function of time) are plotted for 86 of the brighter sources.

  15. Toward a Mechanistic Source Term in Advanced Reactors: Characterization of Radionuclide Transport and Retention in a Sodium Cooled Fast Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Brunett, Acacia J.; Bucknor, Matthew; Grabaskas, David

    2016-04-17

    A vital component of the U.S. reactor licensing process is an integrated safety analysis in which a source term representing the release of radionuclides during normal operation and accident sequences is analyzed. Historically, source term analyses have utilized bounding, deterministic assumptions regarding radionuclide release. However, advancements in technical capabilities and the knowledge state have enabled the development of more realistic and best-estimate retention and release models such that a mechanistic source term assessment can be expected to be a required component of future licensing of advanced reactors. Recently, as part of a Regulatory Technology Development Plan effort for sodium cooled fast reactors (SFRs), Argonne National Laboratory has investigated the current state of knowledge of potential source terms in an SFR via an extensive review of previous domestic experiments, accidents, and operation. As part of this work, the significant sources and transport processes of radionuclides in an SFR have been identified and characterized. This effort examines all stages of release and source term evolution, beginning with release from the fuel pin and ending with retention in containment. Radionuclide sources considered in this effort include releases originating both in-vessel (e.g. in-core fuel, primary sodium, cover gas cleanup system, etc.) and ex-vessel (e.g. spent fuel storage, handling, and movement). Releases resulting from a primary sodium fire are also considered as a potential source. For each release group, dominant transport phenomena are identified and qualitatively discussed. The key product of this effort was the development of concise, inclusive diagrams that illustrate the release and retention mechanisms at a high level, where unique schematics have been developed for in-vessel, ex-vessel and sodium fire releases. This review effort has also found that despite the substantial range of phenomena affecting radionuclide release, the

  16. Refined Source Terms in WAVEWATCH III with Wave Breaking and Sea Spray Forecasts

    Science.gov (United States)

    2015-09-30

    dissipation and breaking, nonlinear wave-wave interaction, bottom friction, wave-mud interaction, wave-current interaction as well as sea spray flux. These...shallow water outside the surf zone. After careful testing within a comprehensive suite of test bed cases, these refined source terms will be...aim to refine the parameterization of air-sea and upper ocean fluxes, including wind input and sea spray as well as dissipation, and hence improve

  17. A Source Term Calculation for the APR1400 NSSS Auxiliary System Components Using the Modified SHIELD Code

    International Nuclear Information System (INIS)

    Park, Hong Sik; Kim, Min; Park, Seong Chan; Seo, Jong Tae; Kim, Eun Kee

    2005-01-01

    The SHIELD code has been used to calculate the source terms of NSSS Auxiliary System (comprising CVCS, SIS, and SCS) components of the OPR1000. Because the code had been developed based upon the SYSTEM80 design and the APR1400 NSSS Auxiliary System design is considerably changed from that of SYSTEM80 or OPR1000, the SHIELD code cannot be used directly for APR1400 radiation design. Thus the hand-calculation is needed for the portion of design changes using the results of the SHIELD code calculation. In this study, the SHIELD code is modified to incorporate the APR1400 design changes and the source term calculation is performed for the APR1400 NSSS Auxiliary System components

  18. Running the source term code package in Elebra MX-850

    International Nuclear Information System (INIS)

    Guimaraes, A.C.F.; Goes, A.G.A.

    1988-01-01

    The source term package (STCP) is one of the main tools applied in calculations of behavior of fission products from nuclear power plants. It is a set of computer codes to assist the calculations of the radioactive materials leaving from the metallic containment of power reactors to the environment during a severe reactor accident. The original version of STCP runs in SDC computer systems, but as it has been written in FORTRAN 77, is possible run it in others systems such as IBM, Burroughs, Elebra, etc. The Elebra MX-8500 version of STCP contains 5 codes:March 3, Trapmelt, Tcca, Vanessa and Nava. The example presented in this report has taken into consideration a small LOCA accident into a PWR type reactor. (M.I.)

  19. Tank waste source term inventory validation. Volume II. Letter report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-04-01

    This document comprises Volume II of the Letter Report entitled Tank Waste Source Term Inventory Validation. This volume contains Appendix C, Radionuclide Tables, and Appendix D, Chemical Analyte Tables. The sample data for selection of 11 radionuclides and 24 chemical analytes were extracted from six separate sample data sets, were arranged in a tabular format and were plotted on scatter plots for all of the 149 single-shell tanks, the 24 double-shell tanks and the four aging waste tanks. The solid and liquid sample data was placed in separate tables and plots. The sample data and plots were compiled from the following data sets: characterization raw sample data, recent core samples, D. Braun data base, Wastren (Van Vleet) data base, TRAC and HTCE inventories.

  20. Tank waste source term inventory validation. Volume II. Letter report

    International Nuclear Information System (INIS)

    1995-04-01

    This document comprises Volume II of the Letter Report entitled Tank Waste Source Term Inventory Validation. This volume contains Appendix C, Radionuclide Tables, and Appendix D, Chemical Analyte Tables. The sample data for selection of 11 radionuclides and 24 chemical analytes were extracted from six separate sample data sets, were arranged in a tabular format and were plotted on scatter plots for all of the 149 single-shell tanks, the 24 double-shell tanks and the four aging waste tanks. The solid and liquid sample data was placed in separate tables and plots. The sample data and plots were compiled from the following data sets: characterization raw sample data, recent core samples, D. Braun data base, Wastren (Van Vleet) data base, TRAC and HTCE inventories

  1. Lanthanum-modified drinking water treatment residue for initial rapid and long-term equilibrium phosphorus immobilization to control eutrophication.

    Science.gov (United States)

    Wang, Changhui; Wu, Yu; Wang, Youquan; Bai, Leilei; Jiang, Helong; Yu, Juhua

    2018-06-15

    This study presents an approach for developing inactivating materials to achieve an initial rapid and a long-term equilibrium P immobilization to control eutrophication based on drinking water treatment residue (DWTR), which is a byproduct of potable water production. By taking advantage of the long-term equilibrium P adsorption by DWTR, the La chemical properties, and the previous success of using La-modified bentonite clay (Phoslock ® ), we used DWTR as a La carrier with different ratios to develop the specific materials. The La loading mechanisms, the potentially toxic effect of La-modified DWTR on snail Bellamya aeruginosa (within 120 d), and the short- and long-term (within 80 d) P immobilization characteristics of the modified DWTR were investigated to understand the performance of the developed materials. The results showed that La loading into DWTR was based on ligand exchanges and the formation of new particles; DWTR loaded with <5% La had no toxicity against the snail. Most importantly, the loading of 5% La to DWTR substantially enhanced the rapid immobilization capacity of DWTR, achieving an initial rapid and a long-term equilibrium P adsorption in aqueous solutions. This study promotes the beneficial recycling of DWTR and results in a win-win situation for lake restoration. Copyright © 2018 Elsevier Ltd. All rights reserved.

  2. An appreciation of the events, models and data used for LMFBR radiological source term estimations

    International Nuclear Information System (INIS)

    Keir, D.; Clough, P.N.

    1989-01-01

    In this report, the events, models and data currently available for analysis of accident source terms in liquid metal cooled fast neutron reactors are reviewed. The types of hypothetical accidents considered are the low probability, more extreme types of severe accident, involving significant degradation of the core and which may lead to the release of radionuclides. The base case reactor design considered is a commercial scale sodium pool reactor of the CDFR type. The feasibility of an integrated calculational approach to radionuclide transport and speciation (such as is used for LWR accident analysis) is explored. It is concluded that there is no fundamental obstacle, in terms of scientific data or understanding of the phenomena involved, to such an approach. However this must be regarded as a long-term goal because of the large amount of effort still required to advance development to a stage comparable with LWR studies. Particular aspects of LMFBR severe accident phenomenology which require attention are the behaviour of radionuclides during core disruptive accident bubble formation and evolution, and during the less rapid sequences of core melt under sodium. The basic requirement for improved thermal hydraulic modelling of core, coolant and structural materials, in these and other scenarios, is highlighted as fundamental to the accuracy and realism of source term estimations. The coupling of such modelling to that of radionuclide behaviour is seen as the key to future development in this area

  3. Long-term monitoring of molecular markers can distinguish different seasonal patterns of fecal indicating bacteria sources.

    Science.gov (United States)

    Riedel, Timothy E; Thulsiraj, Vanessa; Zimmer-Faust, Amity G; Dagit, Rosi; Krug, Jenna; Hanley, Kaitlyn T; Adamek, Krista; Ebentier, Darcy L; Torres, Robert; Cobian, Uriel; Peterson, Sophie; Jay, Jennifer A

    2015-03-15

    Elevated levels of fecal indicator bacteria (FIB) have been observed at Topanga Beach, CA, USA. To identify the FIB sources, a microbial source tracking study using a dog-, a gull- and two human-associated molecular markers was conducted at 10 sites over 21 months. Historical data suggest that episodic discharge from the lagoon at the mouth of Topanga Creek is the main source of bacteria to the beach. A decline in creek FIB/markers downstream from upper watershed development and a sharp increase in FIB/markers at the lagoon sites suggest sources are local to the lagoon. At the lagoon and beach, human markers are detected sporadically, dog marker peaks in abundance mid-winter, and gull marker is chronically elevated. Varied seasonal patterns of FIB and source markers were identified showing the importance of applying a suite of markers over long-term spatial and temporal sampling to identify a complex combination of sources of contamination. Copyright © 2014 Elsevier Ltd. All rights reserved.

  4. Description of apparatus for determining radiological source terms of nuclear fuels

    International Nuclear Information System (INIS)

    Baldwin, D.L.; Woodley, R.E.; Holt, F.E.; Archer, D.V.; Steele, R.T.; Whitkop, P.G.

    1985-01-01

    New apparatus have been designed, built and are currently being employed to measure the release of volatile fission products from irradiated nuclear fuel. The system is capable of measuring radiological source terms, particularly for cesium-137, cesium-134, iodine-129 and krypton-85, in various atmospheres at temperatures up to 1200 0 C. The design allows a rapid transient heatup from ambient to full temperature, a hold at maximum temperature for a specified period, and rapid cooldown. Released fission products are measured as deposition on a platinum thermal gradient tube or in a filter/charcoal trap. Noble gases pass through to a multi-channel gamma analyzer. 1 ref., 4 figs

  5. Calculation of the source term for a S1B-sequence at a VVER-1000 type reactor. Part 1

    International Nuclear Information System (INIS)

    Sdouz, G.

    1990-10-01

    The behaviour of the source term in a VVER-1000 type reactor is calculated using the 'Source Term Code Package' (STCP). The input data are based on the russian plant Zaporozhye-5. The selected accident sequence is a small break LOCA in the hot leg followed by loss offsite and onsite electric power (S 1 B-sequence). According to the course of the calculation the results are presented and analyzed for each program. Except for the noble gases all release fractions are lower than 10 -4 . 18 refs., 10 tabs. (Author)

  6. Initial Resuscitation at Delivery and Short Term Neonatal Outcomes in Very-Low-Birth-Weight Infants

    OpenAIRE

    Cho, Su Jin; Shin, Jeonghee; Namgung, Ran

    2015-01-01

    Survival of very-low-birth-weight infants (VLBWI) depends on professional perinatal management that begins at delivery. Korean Neonatal Network data on neonatal resuscitation management and initial care of VLBWI of less than 33 weeks gestation born from January 2013 to June 2014 were reviewed to investigate the current practice of neonatal resuscitation in Korea. Antenatal data, perinatal data, and short-term morbidities were analyzed. Out of 2,132 neonates, 91.7% needed resuscitation at birt...

  7. Initial-boundary value problems for multi-term time-fractional diffusion equations with x-dependent coefficients

    OpenAIRE

    Li, Zhiyuan; Huang, Xinchi; Yamamoto, Masahiro

    2018-01-01

    In this paper, we discuss an initial-boundary value problem (IBVP) for the multi-term time-fractional diffusion equation with x-dependent coefficients. By means of the Mittag-Leffler functions and the eigenfunction expansion, we reduce the IBVP to an equivalent integral equation to show the unique existence and the analyticity of the solution for the equation. Especially, in the case where all the coefficients of the time-fractional derivatives are non-negative, by the Laplace and inversion L...

  8. Analysis of the primary source term for meltdown accidents using MELCOR 1.8.2

    International Nuclear Information System (INIS)

    Schmuck, P.

    1995-01-01

    The MELCOR code describing accident phenomena in the core and primary systems was used for source term calculations and - in the context of the MELCOR Cooperative Assessment Programme - for studying two-phase flows through components such as valves and chokes. Results of the latter studies in comparison to experiments gave hints for an improved calculation of momentum transfer between the phases. (orig.)

  9. Source term for the bounding assessment of the Canadian nuclear fuel waste disposal concept

    International Nuclear Information System (INIS)

    Flavelle, P.

    1996-02-01

    This is the second in a series to derive the bounds of the post-closure hazard of the Canadian nuclear fuel waste disposal concept, based on the premise that it is unnecessary to predict accurately the real hazard if the bounding hazard can be shown to be acceptable. In this report a reference used (Bruce A fuel, 865 GJ/kgU average burnup) is used to derive the source term for contaminant releases from the emplacement canisters. This requires development of a container failure function which defines the age of the fuel when the canister is perforated and flooded. The source term is expressed as the time-dependent fractional release rate from the used fuel or as the time-dependent contaminant concentrations in the canister porewater. It is derived as the superposition of an instant release, comprising the upper bound of the gap and grain boundary inventory in the used fuel, and the long-term dissolution of the used fuel matrix. Several dissolution models (stoichiometric dissolution/preferential leaching) under different conditions (matrix solubility limited/ unlimited; oxidizing/ reducing solubility limits; groundwater flow/ no flow) are evaluated and the one resulting in the highest release rate/ highest porewater concentration is adopted as the bounding case. Comparisons between the models are made on the basis of the potential ingestion hazard of the canister porewater, to account for differences in the hazard of different radionuclides. (author) 20 refs., 4 tabs., 9 figs

  10. An Organizational-Technical Concept to Deal with Open Source Software License Terms

    Directory of Open Access Journals (Sweden)

    Sergius Dyck

    2016-06-01

    Full Text Available Open source software (OSS released under various license terms is widely used as third party libraries in today's software projects. To ensure open source compliance within an organization, a strategic approach to OSS management is needed. As basis for such an approach, we introduce an organizational-technical concept for dealing with the various OSS licenses by using procedural instructions and build automation software. The concept includes the careful consideration of OSS license conditions. The results obtained from this consideration and additional necessary commitments are documented in a so-called license playbook. We introduce procedure instructions enabling a consistent approach for software development using OSS libraries. The procedure instructions are described in a way such that they can be implemented for example for Java projects using the popular build automation tool Apache Maven and the software repository tool Nexus. We give guidance on how to realize such an implementation on basis of automation tools in practice.

  11. Source term experiments project (STEP): aerosol characterization system

    International Nuclear Information System (INIS)

    Schlenger, B.J.; Dunn, P.F.

    1985-01-01

    A series of four experiments has been conducted at Argonne National Laboratory's TREAT Reactor. These experiments, which are sponsored by an international consortium organized by the Electric Power Research Institute, are designed to investigate the source term, i.e., the type, quantity and timing of release of radioactive fission products from a light water reactor to the environment in the event of a severe accident in which the core is insufficiently cooled. The STEP tests have been designed to provide some of the necessary data regarding the magnitude and release rates of volatile fission products from degraded fuel pins, their physical and chemical characteristics, and aerosol formation and transport phenomena of those fission products that condense to form particles in the cooler regions of the reactor beyond the core. These are inpile experiments, whereby the test fuels are heated in a nuclear test reactor by neutron induced fission and subsequent cladding oxidation in steam environments that simulate as closely as practical predicted severe reactor accident conditions. The test sequences cover a range of pressure and fuel heatup rate, and include the effect of Ag/In/Cd control rod material. 1 ref., 8 figs., 1 tab

  12. Source term calculations - Ringhals 2 PWR. Interim report

    Energy Technology Data Exchange (ETDEWEB)

    Johansson, Lise-Lotte

    1998-03-01

    This project was performed within the fifth and final phase of sub-project RAK-2.1 of the Nordic Co-operative Reactor Safety Program, NKS. RAK-2.1 has also included studies of reflooding of degraded core, recriticality and late phase melt progression. Earlier source term calculations for Swedish nuclear power plants are based on the integral code MAAP. A need was recognised to compare these calculations with calculations done with mechanistic codes. In the present work SCDAP/RELAP5 and CONTAIN were used. Only limited results could be obtained within the frame of RAK-2.1, since many problems were encountered using the SCDAP/RELAP5 code. The main obstacle was the extremely long execution times of the MOD3.1 version, but also some dubious fission product calculations. However, some interesting results were obtained for the studied sequence, a total loss of AC power. The report describes the modelling approach for SCDAP/RELAP5 and CONTAIN, and discusses results for the transient including the event of a surge line creep rupture. The study will probably be completed later, providing that an improved SCDAP/RELAP5 code version becomes available 8 refs, 16 figs, 5 tabs

  13. Coming to Terms: A conflict analysis of the usage, in official and unofficial sources, of 'security fence', 'apartheid wall', and other terms for the structure between Israel and the Palestinian Territories

    NARCIS (Netherlands)

    Rogers, R.A.; Ben-David, A.

    2010-01-01

    The official terms for the dividing wall are ‘security fence’ on the Israeli side and ‘apartheid wall’ on the Palestinian side. Both terms fuse two contextually charged notions to describe the construction project. Beyond the two official terms, the structure has been given other names by sources

  14. Age and CD4 count at initiation of antiretroviral therapy in HIV-infected children: effects on long-term T-cell reconstitution.

    Science.gov (United States)

    Lewis, Joanna; Walker, A Sarah; Castro, Hannah; De Rossi, Anita; Gibb, Diana M; Giaquinto, Carlo; Klein, Nigel; Callard, Robin

    2012-02-15

    Effective therapies and reduced AIDS-related morbidity and mortality have shifted the focus in pediatric human immunodeficiency virus (HIV) from minimizing short-term disease progression to maintaining optimal long-term health. We describe the effects of children's age and pre-antiretroviral therapy (ART) CD4 count on long-term CD4 T-cell reconstitution. CD4 counts in perinatally HIV-infected, therapy-naive children in the Paediatric European Network for the Treatment of AIDS 5 trial were monitored following initiation of ART for a median 5.7 years. In a substudy, naive and memory CD4 counts were recorded. Age-standardized measurements were analyzed using monophasic, asymptotic nonlinear mixed-effects models. One hundred twenty-seven children were studied. Older children had lower age-adjusted CD4 counts in the long term and at treatment initiation (P memory CD4 counts increased less, albeit on a faster timescale. It appears the immature immune system can recover well from HIV infection via the naive pool. However, this potential is progressively damaged with age and/or duration of infection. Current guidelines may therefore not optimize long-term immunological health.

  15. Short-Term Memory Stages in Sign vs. Speech: The Source of the Serial Span Discrepancy

    Science.gov (United States)

    Hall, Matthew L.; Bavelier, Daphne

    2011-01-01

    Speakers generally outperform signers when asked to recall a list of unrelated verbal items. This phenomenon is well established, but its source has remained unclear. In this study, we evaluate the relative contribution of the three main processing stages of short-term memory--perception, encoding, and recall--in this effect. The present study…

  16. The initial phase of sudden releases of superheated liquid

    International Nuclear Information System (INIS)

    Schmidli, J.

    1994-04-01

    The catastrophic failure of a pressure vessel containing a liquefied substance, leading to an instantaneous release of its whole contents is considered as one of the major technological hazards. Due to the rapid depressurization caused by vessel failure, the fluid becomes superheated and unstable. Part of the fluid will evaporate using its internal energy and the two-phase mixture forming will be accelerated. This flashing process can be very violent, as experiments and incidents actually happened have shown. In the past, a number of dispersion models were developed to predict the history of an instantaneous release. In most of these models the source term is considered to be a gas volume at rest and not a rapidly expanding aerosol, as could be observed. Furthermore, it is usually assumed that all of the remaining fluid is entrained into the expanding cloud and nothing is deposited on the ground to form a pool. This work concentrates on the initial phase of the sudden release of superheated liquids with the aim to gain a better understanding of the flashing process and of the physical mechanisms involved, leading to a reliable prediction of the source term. Therefore, more than 400 experiments with propane, butane, refrigerant 12 and 114 were conducted. The experiments were initiated by shattering spherical glass flasks of different sizes. The main parameters varied were the liquid superheat and the filling level of the vessel. Using high-speed video and movie recordings and very fast responding measurement devices, it was possible to study the initial phase of such releases during which gravity plays no role. For sufficiently large released internal energy, the initial evolution of the release was always spherical with a constant radial expansion velocity during he first milliseconds until instabilities appeared at the surface of the droplet/vapor cloud that was formed. For all the experimental conditions, the fraction of the initial liquid falling on the ground

  17. Unclassified Source Term and Radionuclide Data for Corrective Action Unit 97: Yucca Flat/Climax Mine, Nevada Test Site, Nevada, Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    Peter Martian

    2009-05-01

    This report documents the evaluation of the information and data available on the unclassified source term and radionuclide contamination for CAU 97: Yucca Flat/Climax Mine. The total residual inventory of radionuclides associated with one or more tests is known as the radiologic source term (RST). The RST is comprised of radionuclides in water, glass, or other phases or mineralogic forms. The hydrologic source term (HST) of an underground nuclear test is the portion of the total RST that is released into the groundwater over time following the test. In this report, the HST represents radionuclide release some time after the explosion and does not include the rapidly evolving mechanical, thermal, and chemical processes during the explosion. The CAU 97: Yucca Flat/Climax Mine has many more detonations and a wider variety of settings to consider compared to other CAUs. For instance, the source term analysis and evaluation performed for CAUs 101 and 102: Central and Western Pahute Mesa and CAU 98: Frenchman Flat did not consider vadose zone attenuation because many detonations were located near or below the water table. However, the large number of Yucca Flat/Climax Mine tests and the location of many tests above the water table warrant a more robust analysis of the unsaturated zone.

  18. Adiabatic energization in the ring current and its relation to other source and loss terms

    Science.gov (United States)

    Liemohn, M. W.; Kozyra, J. U.; Clauer, C. R.; Khazanov, G. V.; Thomsen, M. F.

    2002-04-01

    The influence of adiabatic energization and deenergization effects, caused by particle drift in radial distance, on ring current growth rates and loss lifetimes is investigated. Growth and loss rates from simulation results of four storms (5 June 1991, 15 May 1997, 19 October 1998, and 25 September 1998) are examined and compared against the y component of the solar wind electric field (Ey,sw). Energy change rates with and without the inclusion of adiabatic energy changes are considered to isolate the influence of this mechanism in governing changes of ring current strength. It is found that the influence of adiabatic drift effects on the energy change rates is very large when energization and deenergization are considered separately as gain and loss mechanisms, often about an order of magnitude larger than all other source or loss terms combined. This is true not only during storm times, when the open drift path configuration of the hot ions dominates the physics of the ring current, but also during quiet times, when the small oscillation in L of the closed trajectories creates a large source and loss of energy each drift orbit. However, the net energy change from adiabatic drift is often smaller than other source and loss processes, especially during quiet times. Energization from adiabatic drift dominates ring current growth only during portions of the main phase of storms. Furthermore, the net-adiabatic energization is often positive, because some particles are lost in the inner magnetosphere before they can adiabatically deenergize. It is shown that the inclusion of only this net-adiabatic drift effect in the total source rate or loss lifetime (depending on the sign of the net-adiabatic energization) best matches the observed source and loss values from empirical Dst predictor methods (that is, for consistency, these values should be compared between the calculation methods). While adiabatic deenergization dominates the loss timescales for all Ey,sw values

  19. An improvement of estimation method of source term to the environment for interfacing system LOCA for typical PWR using MELCOR code

    Energy Technology Data Exchange (ETDEWEB)

    Han, Seok Jung; Kim, Tae Woon; Ahn, Kwang Il [Risk and Environmental Safety Research Division, Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2017-06-15

    Interfacing-system loss-of-coolant-accident (ISLOCA) has been identified as the most hazardous accident scenario in the typical PWR plants. The present study as an effort to improve the knowledge of the source term to the environment during ISLOCA focuses on an improvement of the estimation method. The improvement was performed to take into account an effect of broken pipeline and auxiliary building structures relevant to ISLOCA. An estimation of the source term to the environment was for the OPR-1000 plants by MELOCR code version 1.8.6. The key features of the source term showed that the massive amount of fission products departed from the beginning of core degradation to the vessel breach. The release amount of fission products may be affected by the broken pipeline and the auxiliary building structure associated with release pathway.

  20. Geometric discretization of the multidimensional Dirac delta distribution - Application to the Poisson equation with singular source terms

    Science.gov (United States)

    Egan, Raphael; Gibou, Frédéric

    2017-10-01

    We present a discretization method for the multidimensional Dirac distribution. We show its applicability in the context of integration problems, and for discretizing Dirac-distributed source terms in Poisson equations with constant or variable diffusion coefficients. The discretization is cell-based and can thus be applied in a straightforward fashion to Quadtree/Octree grids. The method produces second-order accurate results for integration. Superlinear convergence is observed when it is used to model Dirac-distributed source terms in Poisson equations: the observed order of convergence is 2 or slightly smaller. The method is consistent with the discretization of Dirac delta distribution for codimension one surfaces presented in [1,2]. We present Quadtree/Octree construction procedures to preserve convergence and present various numerical examples, including multi-scale problems that are intractable with uniform grids.

  1. Regulatory Technology Development Plan - Sodium Fast Reactor. Mechanistic Source Term - Metal Fuel Radionuclide Release

    International Nuclear Information System (INIS)

    Grabaskas, David; Bucknor, Matthew; Jerden, James

    2016-01-01

    The development of an accurate and defensible mechanistic source term will be vital for the future licensing efforts of metal fuel, pool-type sodium fast reactors. To assist in the creation of a comprehensive mechanistic source term, the current effort sought to estimate the release fraction of radionuclides from metal fuel pins to the primary sodium coolant during fuel pin failures at a variety of temperature conditions. These release estimates were based on the findings of an extensive literature search, which reviewed past experimentation and reactor fuel damage accidents. Data sources for each radionuclide of interest were reviewed to establish release fractions, along with possible release dependencies, and the corresponding uncertainty levels. Although the current knowledge base is substantial, and radionuclide release fractions were established for the elements deemed important for the determination of offsite consequences following a reactor accident, gaps were found pertaining to several radionuclides. First, there is uncertainty regarding the transport behavior of several radionuclides (iodine, barium, strontium, tellurium, and europium) during metal fuel irradiation to high burnup levels. The migration of these radionuclides within the fuel matrix and bond sodium region can greatly affect their release during pin failure incidents. Post-irradiation examination of existing high burnup metal fuel can likely resolve this knowledge gap. Second, data regarding the radionuclide release from molten high burnup metal fuel in sodium is sparse, which makes the assessment of radionuclide release from fuel melting accidents at high fuel burnup levels difficult. This gap could be addressed through fuel melting experimentation with samples from the existing high burnup metal fuel inventory.

  2. Regulatory Technology Development Plan - Sodium Fast Reactor. Mechanistic Source Term - Metal Fuel Radionuclide Release

    Energy Technology Data Exchange (ETDEWEB)

    Grabaskas, David [Argonne National Lab. (ANL), Argonne, IL (United States); Bucknor, Matthew [Argonne National Lab. (ANL), Argonne, IL (United States); Jerden, James [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-02-01

    The development of an accurate and defensible mechanistic source term will be vital for the future licensing efforts of metal fuel, pool-type sodium fast reactors. To assist in the creation of a comprehensive mechanistic source term, the current effort sought to estimate the release fraction of radionuclides from metal fuel pins to the primary sodium coolant during fuel pin failures at a variety of temperature conditions. These release estimates were based on the findings of an extensive literature search, which reviewed past experimentation and reactor fuel damage accidents. Data sources for each radionuclide of interest were reviewed to establish release fractions, along with possible release dependencies, and the corresponding uncertainty levels. Although the current knowledge base is substantial, and radionuclide release fractions were established for the elements deemed important for the determination of offsite consequences following a reactor accident, gaps were found pertaining to several radionuclides. First, there is uncertainty regarding the transport behavior of several radionuclides (iodine, barium, strontium, tellurium, and europium) during metal fuel irradiation to high burnup levels. The migration of these radionuclides within the fuel matrix and bond sodium region can greatly affect their release during pin failure incidents. Post-irradiation examination of existing high burnup metal fuel can likely resolve this knowledge gap. Second, data regarding the radionuclide release from molten high burnup metal fuel in sodium is sparse, which makes the assessment of radionuclide release from fuel melting accidents at high fuel burnup levels difficult. This gap could be addressed through fuel melting experimentation with samples from the existing high burnup metal fuel inventory.

  3. Multiple-shock initiation via statistical crack mechanics

    Energy Technology Data Exchange (ETDEWEB)

    Dienes, J.K.; Kershner, J.D.

    1998-12-31

    Statistical Crack Mechanics (SCRAM) is a theoretical approach to the behavior of brittle materials that accounts for the behavior of an ensemble of microcracks, including their opening, shear, growth, and coalescence. Mechanical parameters are based on measured strain-softening behavior. In applications to explosive and propellant sensitivity it is assumed that closed cracks act as hot spots, and that the heating due to interfacial friction initiates reactions which are modeled as one-dimensional heat flow with an Arrhenius source term, and computed in a subscale grid. Post-ignition behavior of hot spots is treated with the burn model of Ward, Son and Brewster. Numerical calculations using SCRAM-HYDROX are compared with the multiple-shock experiments of Mulford et al. in which the particle velocity in PBX 9501 is measured with embedded wires, and reactions are initiated and quenched.

  4. The source term and waste optimization of molten salt reactors with processing

    International Nuclear Information System (INIS)

    Gat, U.; Dodds, H.L.

    1993-01-01

    The source term of a molten salt reactor (MSR) with fuel processing is reduced by the ratio of processing time to refueling time as compared to solid fuel reactors. The reduction, which can be one to two orders of magnitude, is due to removal of the long-lived fission products. The waste from MSRs can be optimized with respect to its chemical composition, concentration, mixture, shape, and size. The actinides and long-lived isotopes can be separated out and returned to the reactor for transmutation. These features make MSRs more acceptable and simpler in operation and handling

  5. A Source Term for Wave Attenuation by Sea Ice in WAVEWATCH III (registered trademark): IC4

    Science.gov (United States)

    2017-06-07

    blue and 4 locations in the ice: 1, 2, 5, and 10 km. Notice the steepening of the high frequency face and the shift of the peak to slightly lower...Term for Wave Attenuation by Sea Ice in WAVEWATCH III®: IC4 ClarenCe O. COllins iii W. eriCk rOgers Ocean Dynamics and Prediction Branch Oceanography...Wave model Sea ice Ocean surface waves Arctic Ocean WAVEWATCH III Spectral wave modeling Source terms Wave hindcasting 73-N2K2-07-5 Naval Research

  6. Models of Disease Vector Control: When Can Aggressive Initial Intervention Lower Long-Term Cost?

    Science.gov (United States)

    Oduro, Bismark; Grijalva, Mario J; Just, Winfried

    2018-04-01

    Insecticide spraying of housing units is an important control measure for vector-borne infections such as Chagas disease. As vectors may invade both from other infested houses and sylvatic areas and as the effectiveness of insecticide wears off over time, the dynamics of (re)infestations can be approximated by [Formula: see text]-type models with a reservoir, where housing units are treated as hosts, and insecticide spraying corresponds to removal of hosts. Here, we investigate three ODE-based models of this type. We describe a dual-rate effect where an initially very high spraying rate can push the system into a region of the state space with low endemic levels of infestation that can be maintained in the long run at relatively moderate cost, while in the absence of an aggressive initial intervention the same average cost would only allow a much less significant reduction in long-term infestation levels. We determine some sufficient and some necessary conditions under which this effect occurs and show that it is robust in models that incorporate some heterogeneity in the relevant properties of housing units.

  7. Spinal epidural neurostimulation for treatment of acute and chronic intractable pain: initial and long term results.

    Science.gov (United States)

    Richardson, R R; Siqueira, E B; Cerullo, L J

    1979-09-01

    Spinal epidural neurostimulation, which evolved from dorsal column stimulation, has been found to be effective in the treatment of acute and chronic intractable pain. Urban and Hashold have shown that it is a safe, simplified alternative to dorsal column stimulation, especially because laminectomy is not required if the electrodes are inserted percutaneously. Percutaneous epidural neurostimulation is also advantageous because there can be a diagnostic trial period before permanent internalization and implantation. This diagnostic and therapeutic modality has been used in 36 patients during the past 3 years at Northwestern Memorial Hospital. Eleven of these patients had acute intractable pain, which was defined as pain of less than 1 year in duration. Initial postimplantation results from the 36 patients indicate that spinal epidural neurostimulation is most effective in treating the intractable pain of diabetes, arachnoiditis, and post-traumatic and postamputation neuroma. Long term follow-up, varying from 1 year to 3 years postimplantation in the 20 initially responding patients, indicates that the neurostimulation continues to provide significant pain relief (50% or greater) in a majority of the patients who experienced initial significant pain relief.

  8. Subcriticality calculation in nuclear reactors with external neutron sources

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Adilson Costa da; Martinez, Aquilino Senra; Silva, Fernando Carvalho da [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE). Programa de Engenharia Nuclear]. E-mails: asilva@con.ufrj.br; aquilino@lmp.ufrj.br; fernando@con.ufrj.br

    2007-07-01

    The main objective of this paper consists on the development of a methodology to monitor subcriticality. We used the inverse point kinetic equation with 6 precursor groups and external neutron sources for the calculation of reactivity. The input data for the inverse point kinetic equation was adjusted, in order to use the neutron counting rates obtained from the subcritical multiplication (1/M) in a nuclear reactor. In this paper, we assumed that the external neutron sources strength is constant and we define it in terms of a known initial condition. The results obtained from inverse point kinetic equation with external neutron sources were compared with the results obtained with a benchmark calculation, and showed good accuracy (author)

  9. Subcriticality calculation in nuclear reactors with external neutron sources

    International Nuclear Information System (INIS)

    Silva, Adilson Costa da; Martinez, Aquilino Senra; Silva, Fernando Carvalho da

    2007-01-01

    The main objective of this paper consists on the development of a methodology to monitor subcriticality. We used the inverse point kinetic equation with 6 precursor groups and external neutron sources for the calculation of reactivity. The input data for the inverse point kinetic equation was adjusted, in order to use the neutron counting rates obtained from the subcritical multiplication (1/M) in a nuclear reactor. In this paper, we assumed that the external neutron sources strength is constant and we define it in terms of a known initial condition. The results obtained from inverse point kinetic equation with external neutron sources were compared with the results obtained with a benchmark calculation, and showed good accuracy (author)

  10. Integral migration and source term experiments on cement and bitumen waste forms

    International Nuclear Information System (INIS)

    Ewart, F.T.; Howse, R.M.; Sharpe, B.M.; Smith, A.J.; Thomason, H.P.; Williams, S.J.; Young, M.

    1986-01-01

    This is the final report of a programme of research which formed a part of the CEC joint research project into radionuclide migration in the geosphere (MIRAGE). This study addressed the aspects of integral migration and source term. The integral migration experiment simulated, in the laboratory, the intrusion of water into the repository, the leaching of radionuclides from two intermediate level wasteforms and the subsequent migration through the geosphere. The simulation consisted of a source of natural ground water which flowed over a sample of wasteform, at a controlled redox potential, and then through backfill and geological material packed in columns. The two wasteforms used here were cemented waste from the WAK plant at Karlsruhe, W. Germany and bitumenised intermediate concentrates from the Marcoule plant in France. The soluble fission products such as caesium wire rapidly released from the cemented waste but the actinides, and technetium in the reduced state, were retained in the wasteform. The release of all nuclides from the bitumenised waste was very low. (author)

  11. Integral migration and source-term experiments on cement and bitumen waste forms

    International Nuclear Information System (INIS)

    Ewart, F.T.; Howse, R.M.; Sharpe, B.M.; Smith, A.J.; Thomason, H.P.; Williams, S.J.; Young, M.

    1986-01-01

    This is the final report of a programme of research which formed a part of the CEC joint research project into radionuclide migration in the geosphere (MIRAGE). This study addressed the aspects of integral migration and source term. The integral migration experiment simulated, in the laboratory, the intrusion of water into the repository, the leaching of radionuclides from two intermediate-level waste-forms and the subsequent migration through the geosphere. The simulation consisted of a source of natural ground water which flowed over a sample of waste-form, at a controlled redox potential, and then through backfill and geological material packed in columns. The two waste forms used here were cemented waste from the WAK plant at Karlsruhe in the Federal Republic of Germany and bitumenized intermediate concentrates from the Marcoule plant in France. The soluble fission products such as caesium were rapidly released from the cemented waste but the actinides, and technetium in the reduced state, were retained in the waste-form. The released of all nuclides from the bitumenized waste was very low

  12. New source terms and the implications for emergency planning requirements at nuclear power plants in the United State

    International Nuclear Information System (INIS)

    Kaiser, G.D.; Cheok, M.C.

    1987-01-01

    This paper begins with a brief review of current approaches to source term driven changes to NRC emergency planning requirements and addresses significant differences between them. Approaches by IDCOR and EPRI, industry submittals to NRC and alternative risk-based evaluations have been considered. Important issues are discussed, such as the role of Protective Action Guides in determining the radius of the emergency planning zone (EPZ). The significance of current trends towards the prediction of longer warning times and longer durations of release in new source terms is assessed. These trends may help to relax the current notification time requirements. Finally, the implications of apparent support in the regulations for a threshold in warning time beyond which ad hoc protective measures are adequate is discussed

  13. Operational techniques employed for the liquid sodium source term control loops

    International Nuclear Information System (INIS)

    Chulos, L.E.

    1976-01-01

    Four Source Term Control Loops (STCLs) have been designed, constructed, and placed into operation at the Hanford Engineering Development Laboratory (HEDL) as part of the Radioactivity Control Technology program. The data obtained are used to determine the corrosion and deposition of LMFBR materials, including corrosion product radionuclides, in a non-isothermal flowing sodium system. The paper discusses operation of the STCL Facilities and, in particular, the methods used for controlling the oxygen content of the liquid sodium. These methods include cold trapping techniques, hot trapping, seeding the cold traps with sodium oxide, and precipitating the oxygen in the cold trap in a controlled manner. Operational problems encountered with the STCL Facilities and the techniques for correcting these problems are also discussed

  14. Determination of Source Term for an Annual Stack Release of Gas Reactor G.A. Siwabessy

    International Nuclear Information System (INIS)

    Sudiyati; Syahrir; Unggul Hartoyo; Nugraha Luhur

    2008-01-01

    Releases of radionuclide from the reactor are noble gases, halogenides and particulates. The measurements were carried out directly on the air monitoring system of the stack. The results of these measurements are compared with the annual Source-Term data from the Safety Analyses report (SAR) of RSG-GAS. The measurement results are smaller than the data reported in SAR document. (author)

  15. Initial Weight Loss after Restrictive Bariatric Procedures May Predict Mid-Term Weight Maintenance: Results From a 12-Month Pilot Trial

    OpenAIRE

    Nikolić, Marko; Kruljac, Ivan; Kirigin, Lora; Mirošević, Gorana; Ljubičić, Neven; Nikolić, Borka Pezo; Bekavac-Bešlin, Miroslav; Budimir, Ivan; Vrkljan, Milan

    2015-01-01

    Background: Bariatric procedures are effective options for weight loss (WL) in the morbidly obese. However, some patients fail to lose any weight after bariatric surgery, and mid-term weight maintenance is variable. The aim of this study was to investigate whether initial WL could predict mid-term weight maintenance. ----- Methods: Eighty patients were enrolled, of whom 44 were treated with the BioEnterics Intragastric Balloon (BIB), 21 with laparoscopic adjustable gastric lap-banding (LAGB),...

  16. Long-term storage life of light source modules by temperature cycling accelerated life test

    International Nuclear Information System (INIS)

    Sun Ningning; Tan Manqing; Li Ping; Jiao Jian; Guo Xiaofeng; Guo Wentao

    2014-01-01

    Light source modules are the most crucial and fragile devices that affect the life and reliability of the interferometric fiber optic gyroscope (IFOG). While the light emitting chips were stable in most cases, the module packaging proved to be less satisfactory. In long-term storage or the working environment, the ambient temperature changes constantly and thus the packaging and coupling performance of light source modules are more likely to degrade slowly due to different materials with different coefficients of thermal expansion in the bonding interface. A constant temperature accelerated life test cannot evaluate the impact of temperature variation on the performance of a module package, so the temperature cycling accelerated life test was studied. The main failure mechanism affecting light source modules is package failure due to solder fatigue failure including a fiber coupling shift, loss of cooling efficiency and thermal resistor degradation, so the Norris-Landzberg model was used to model solder fatigue life and determine the activation energy related to solder fatigue failure mechanism. By analyzing the test data, activation energy was determined and then the mean life of light source modules in different storage environments with a continuously changing temperature was simulated, which has provided direct reference data for the storage life prediction of IFOG. (semiconductor devices)

  17. DUSTMS-D: DISPOSAL UNIT SOURCE TERM - MULTIPLE SPECIES - DISTRIBUTED FAILURE DATA INPUT GUIDE.

    Energy Technology Data Exchange (ETDEWEB)

    SULLIVAN, T.M.

    2006-01-01

    Performance assessment of a low-level waste (LLW) disposal facility begins with an estimation of the rate at which radionuclides migrate out of the facility (i.e., the source term). The focus of this work is to develop a methodology for calculating the source term. In general, the source term is influenced by the radionuclide inventory, the wasteforms and containers used to dispose of the inventory, and the physical processes that lead to release from the facility (fluid flow, container degradation, wasteform leaching, and radionuclide transport). Many of these physical processes are influenced by the design of the disposal facility (e.g., how the engineered barriers control infiltration of water). The complexity of the problem and the absence of appropriate data prevent development of an entirely mechanistic representation of radionuclide release from a disposal facility. Typically, a number of assumptions, based on knowledge of the disposal system, are used to simplify the problem. This has been done and the resulting models have been incorporated into the computer code DUST-MS (Disposal Unit Source Term-Multiple Species). The DUST-MS computer code is designed to model water flow, container degradation, release of contaminants from the wasteform to the contacting solution and transport through the subsurface media. Water flow through the facility over time is modeled using tabular input. Container degradation models include three types of failure rates: (a) instantaneous (all containers in a control volume fail at once), (b) uniformly distributed failures (containers fail at a linear rate between a specified starting and ending time), and (c) gaussian failure rates (containers fail at a rate determined by a mean failure time, standard deviation and gaussian distribution). Wasteform release models include four release mechanisms: (a) rinse with partitioning (inventory is released instantly upon container failure subject to equilibrium partitioning (sorption) with

  18. Impact of Infection Prevention and Control Initiatives on Acute Respiratory Infections in a Pediatric Long-Term Care Facility.

    Science.gov (United States)

    Murray, Meghan T; Jackson, Olivia; Cohen, Bevin; Hutcheon, Gordon; Saiman, Lisa; Larson, Elaine; Neu, Natalie

    2016-07-01

    We evaluated the collective impact of several infection prevention and control initiatives aimed at reducing acute respiratory infections (ARIs) in a pediatric long-term care facility. ARIs did not decrease overall, though the proportion of infections associated with outbreaks and average number of cases per outbreak decreased. Influenza rates decreased significantly. Infect Control Hosp Epidemiol 2016;37:859-862.

  19. Interlaboratory study of the ion source memory effect in 36Cl accelerator mass spectrometry

    International Nuclear Information System (INIS)

    Pavetich, Stefan; Akhmadaliev, Shavkat; Arnold, Maurice; Aumaître, Georges; Bourlès, Didier; Buchriegler, Josef; Golser, Robin; Keddadouche, Karim; Martschini, Martin; Merchel, Silke; Rugel, Georg; Steier, Peter

    2014-01-01

    Highlights: • Long-term memory effect in negative ion sources investigated for chlorine isotopes. • Interlaboratory comparison of four up-to date negative ion sources. • Ion source improvement at DREAMS for minimization of long-term memory effect. • Long-term memory effect is the limitation for precise AMS data of volatile elements. • Findings to be considered for samples with highly variable ratios of 36 Cl/Cl and 129 I/I. - Abstract: Understanding and minimization of contaminations in the ion source due to cross-contamination and long-term memory effect is one of the key issues for accurate accelerator mass spectrometry (AMS) measurements of volatile elements. The focus of this work is on the investigation of the long-term memory effect for the volatile element chlorine, and the minimization of this effect in the ion source of the Dresden accelerator mass spectrometry facility (DREAMS). For this purpose, one of the two original HVE ion sources at the DREAMS facility was modified, allowing the use of larger sample holders having individual target apertures. Additionally, a more open geometry was used to improve the vacuum level. To evaluate this improvement in comparison to other up-to-date ion sources, an interlaboratory comparison had been initiated. The long-term memory effect of the four Cs sputter ion sources at DREAMS (two sources: original and modified), ASTER (Accélérateur pour les Sciences de la Terre, Environnement, Risques) and VERA (Vienna Environmental Research Accelerator) had been investigated by measuring samples of natural 35 Cl/ 37 Cl-ratio and samples highly-enriched in 35 Cl ( 35 Cl/ 37 Cl ∼ 999). Besides investigating and comparing the individual levels of long-term memory, recovery time constants could be calculated. The tests show that all four sources suffer from long-term memory, but the modified DREAMS ion source showed the lowest level of contamination. The recovery times of the four ion sources were widely spread between

  20. Review of specific effects in atmospheric dispersion calculations. The impact of source-term characteristics -and the processes that modify them post release- on dry and wet deposition rates

    International Nuclear Information System (INIS)

    Cooper, P.J.; Underwood, B.Y.; Brearley, I.

    1985-01-01

    In the first half of the work the source-term characteristics potentially influencing behaviour were identified and examined. It was concluded that a number of source characteristics, in addition to those conventionally provided for consequence assessment, could significantly influence deposition behaviour. Linking with this, a review was undertaken of past reactor-accident risk assessment and more recent source-term studies to pick out information, if any, on the parameters of interest. The second half of the study resulted in a list of processes capable of transforming the released material vis-a-vis deposition characteristics, including processes occurring in the near field associated with the initial release transient and also those occurring over a longer time span as the plume travels downwind. Scoping calculations were performed for some of the processes in the context of idealized accident scenarios, leading to the conclusions that in some circumstances post-release mechanisms could have an important impact on the deposition behaviour of released material. Statistical theory was used to describe the behaviour of a plume both before and after detachment, and the limitations of the theory were discussed. A review of the lateral wind velocity spectra was undertaken so that simplified spectra could be constructed and used to predict the plume behaviour as a function of travel time, stability category and release duration. It was found that commonly used methods of allowing for release duration overpredicted the dependence, in general, upon release duration. For example the adoption of a stability-independent meandering term would lead to the underprediction of threshold effects such as early death and land/crop interdiction. In addition, theory indicated that the 'Y' curves for different stability categories would converge gradually with increasing travel time

  1. Parameterizing unresolved obstacles with source terms in wave modeling: A real-world application

    Science.gov (United States)

    Mentaschi, Lorenzo; Kakoulaki, Georgia; Vousdoukas, Michalis; Voukouvalas, Evangelos; Feyen, Luc; Besio, Giovanni

    2018-06-01

    Parameterizing the dissipative effects of small, unresolved coastal features, is fundamental to improve the skills of wave models. The established technique to deal with this problem consists in reducing the amount of energy advected within the propagation scheme, and is currently available only for regular grids. To find a more general approach, Mentaschi et al., 2015b formulated a technique based on source terms, and validated it on synthetic case studies. This technique separates the parameterization of the unresolved features from the energy advection, and can therefore be applied to any numerical scheme and to any type of mesh. Here we developed an open-source library for the estimation of the transparency coefficients needed by this approach, from bathymetric data and for any type of mesh. The spectral wave model WAVEWATCH III was used to show that in a real-world domain, such as the Caribbean Sea, the proposed approach has skills comparable and sometimes better than the established propagation-based technique.

  2. 78 FR 7860 - Initial Research on the Long-Term Health Consequences of Exposure to Burn Pits in Iraq and...

    Science.gov (United States)

    2013-02-04

    ... epidemiologic research initiatives for VA and DoD to further study potential long-term health effects. IOM first... examined through a research-based physical examination component of a broader research program. As a first step, VA intends to develop research goals and objectives, structures, and establish essential study...

  3. Unclassified Sources Term and Radionuclide Data for Corrective Action Unit 97: Yucca Flat/Climax Mine, Nevada Test Site, Nevada, Revision 2

    Energy Technology Data Exchange (ETDEWEB)

    Peter Martian

    2009-08-01

    This report documents the evaluation of the information and data available on the unclassified source term and radionuclide contamination for CAU 97: Yucca Flat/Climax Mine. The total residual inventory of radionuclides associated with one or more tests is known as the radiologic source term (RST). The RST is comprised of radionuclides in water, glass, or other phases or mineralogic forms. The hydrologic source term (HST) of an underground nuclear test is the portion of the total RST that is released into the groundwater over time following the test. In this report, the HST represents radionuclide release some time after the explosion and does not include the rapidly evolving mechanical, thermal, and chemical processes during the explosion. The CAU 97: Yucca Flat/Climax Mine has many more detonations and a wider variety of settings to consider compared to other CAUs. For instance, the source term analysis and evaluation performed for CAUs 101 and 102: Central and Western Pahute Mesa and CAU 98: Frenchman Flat did not consider vadose zone attenuation because many detonations were located near or below the water table. However, the large number of Yucca Flat/Climax Mine tests and the location of many tests above the water table warrant a more robust analysis of the unsaturated zone. The purpose of this report is to develop and document conceptual models of the Yucca Flat/Climax Mine HST for use in implementing source terms for the Yucca Flat/Climax Mine models. This document presents future plans to incorporate the radionuclide attenuation mechanisms due to unsaturated/multiphase flow and transport within the Yucca Flat CAU scale modeling. The important processes that influence radionuclide migration for the unsaturated and saturated tests in alluvial, volcanic, and carbonate settings are identified. Many different flow and transport models developed by Lawrence Livermore National Laboratory (LLNL) and Los Alamos National Laboratory (LANL), including original

  4. Determination of the in-containment source term for a Large-Break Loss of Coolant Accident

    International Nuclear Information System (INIS)

    2001-04-01

    This is the report of a project that focused on one of the most important design basis accidents: the Large Break Loss Of Coolant Accident (LBLOCA) (for pressurised water reactors). The first step in the calculation of the radiological consequences of this accident is the determination of the source term inside the containment. This work deals with this part of the calculation of the LBLOCA radiological consequences for which a previous benchmark (1988) has shown wide variations in the licensing practices adopted by European countries. The calculation of this source term may naturally be split in several steps (see chapter II), corresponding to several physical stages in the release of fission products: fraction of core failure, release from the damaged fuel, airborne part of the release and the release into the reactor coolant system and the sumps, chemical behaviour of iodine in the aqueous and gas phases, natural and spray removal in the containment atmosphere. A chapter is devoted to each of these topics. In addition, two other chapters deal with the basic assumptions to define the accidental sequence and the nuclides to be considered when computing doses associated with the LBLOCA. The report describes where there is agreement between the partner organisations and where there are still differences in approach. For example, there is agreement concerning the percentage of failed fuel which could be used in future licensing assessments (however this subject is still under discussion in France, a lower value is thinkable). For existing plants, AVN (Belgium) wishes to keep the initial licensing assumptions. For the release from damaged fuel, there is not complete agreement: AVN (Belgium) wishes to maintain its present approach. IPSN (France), GRS (Germany) and NNC (UK) prefer to use their own methodologies that result in slightly different values to the proposed values for a common position. There are presently no recommendations of the release of fuel particulates

  5. Creating Long Term Income Streams for the 100 Year Starship Study Initiative

    Science.gov (United States)

    Sylvester, A. J.

    Development and execution of long term research projects are very dependent on a consistent application of funding to maximize the potential for success. The business structure for the 100 Year Starship Study project should allow for multiple income streams to cover the expenses of the research objectives. The following examples illustrate the range of potential avenues: 1) affiliation with a charitable foundation for creating a donation program to fund a long term endowment for research, 2) application for grants to fund initial research projects and establish the core expertise of the research entity, 3) development of intellectual property which can then be licensed for additional revenue, 4) creation of spinout companies with equity positions retained by the lab for funding the endowment, and 5) funded research which is dual use for the technology goals of the interstellar flight research objectives. With the establishment of a diversified stream of funding options, then the endowment can be funded at a level to permit dedicated research on the interstellar flight topics. This paper will focus on the strategy of creating spinout companies to create income streams which would fund the endowment of the 100 Year Starship Study effort. This technique is widely used by universities seeking to commercially develop and market technologies developed by university researchers. An approach will be outlined for applying this technique to potentially marketable technologies generated as a part of the 100 Year Starship Study effort.

  6. Long-term outcome of intensive initial immunosuppression protocol in pediatric deceased donor renal transplantation.

    LENUS (Irish Health Repository)

    Olaitan, Oyedolamu K

    2010-02-01

    To report the long-term outcome of deceased donor kidney transplantation in children with emphasis on the use of an intensive initial immunosuppression protocol using R-ATG as antibody induction. Between January 1991 and December 1997, 82 deceased donor kidney transplantations were performed in 75 pediatric recipients. Mean recipient age at transplantation was 12.9 yr and the mean follow-up period was 12.6 yr. All patients received quadruple immunosuppression with steroid, cyclosporine, azathioprine, and antibody induction using R-ATG-Fresenius. Actual one, five, and 10 yr patient survival rates were 99%, 97%, and 94%, respectively; only one patient (1.2%) developed PTLD. Actual one, five, and 10 yr overall graft survival rates were 84%, 71%, and 50%, respectively; there were five cases (6%) of graft thrombosis and the actual immunological graft survival rates were 91%, 78%, and 63% at one, five, and 10 yr, respectively. The use of an intensive initial immunosuppression protocol with R-ATG as antibody induction is safe and effective in pediatric recipients of deceased donor kidneys with excellent immunological graft survival without an increase in PTLD or other neoplasms over a minimum 10-yr follow up.

  7. The role of multidimensional instabilities in direct initiation of gaseous detonations in free space

    KAUST Repository

    Shen, Hua

    2017-01-20

    We numerically investigate the direct initiation of detonations driven by the propagation of a blast wave into a unconfined gaseous combustible mixture to study the role played by multidimensional instabilities in direct initiation of stable and unstable detonations. To this end, we first model the dynamics of unsteady propagation of detonation using the one-dimensional compressible Euler equations with a one-step chemical reaction model and cylindrical geometrical source terms. Subsequently, we use two-dimensional compressible Euler equations with just the chemical reaction source term to directly model cylindrical detonations. The one-dimensional results suggest that there are three regimes in the direct initiation for stable detonations, that the critical energy for mildly unstable detonations is not unique, and that highly unstable detonations are not self-sustainable. These phenomena agree well with one-dimensional theories and computations available in the literature. However, our two-dimensional results indicate that one-dimensional approaches are valid only for stable detonations. In mildly and highly unstable detonations, one-dimensional approaches break down because they cannot take the effects and interactions of multidimensional instabilities into account. In fact, instabilities generated in multidimensional settings yield the formation of strong transverse waves that, on one hand, increase the risk of failure of the detonation and, on the other hand, lead to the initiation of local over-driven detonations that enhance the overall self-sustainability of the global process. The competition between these two possible outcomes plays an important role in the direct initiation of detonations.

  8. Numerical simulation of flow induced by a pitched blade turbine. Comparison of the sliding mesh technique and an averaged source term method

    Energy Technology Data Exchange (ETDEWEB)

    Majander, E.O.J.; Manninen, M.T. [VTT Energy, Espoo (Finland)

    1996-12-31

    The flow induced by a pitched blade turbine was simulated using the sliding mesh technique. The detailed geometry of the turbine was modelled in a computational mesh rotating with the turbine and the geometry of the reactor including baffles was modelled in a stationary co-ordinate system. Effects of grid density were investigated. Turbulence was modelled by using the standard k-{epsilon} model. Results were compared to experimental observations. Velocity components were found to be in good agreement with the measured values throughout the tank. Averaged source terms were calculated from the sliding mesh simulations in order to investigate the reliability of the source term approach. The flow field in the tank was then simulated in a simple grid using these source terms. Agreement with the results of the sliding mesh simulations was good. Commercial CFD-code FLUENT was used in all simulations. (author)

  9. Numerical simulation of flow induced by a pitched blade turbine. Comparison of the sliding mesh technique and an averaged source term method

    Energy Technology Data Exchange (ETDEWEB)

    Majander, E O.J.; Manninen, M T [VTT Energy, Espoo (Finland)

    1997-12-31

    The flow induced by a pitched blade turbine was simulated using the sliding mesh technique. The detailed geometry of the turbine was modelled in a computational mesh rotating with the turbine and the geometry of the reactor including baffles was modelled in a stationary co-ordinate system. Effects of grid density were investigated. Turbulence was modelled by using the standard k-{epsilon} model. Results were compared to experimental observations. Velocity components were found to be in good agreement with the measured values throughout the tank. Averaged source terms were calculated from the sliding mesh simulations in order to investigate the reliability of the source term approach. The flow field in the tank was then simulated in a simple grid using these source terms. Agreement with the results of the sliding mesh simulations was good. Commercial CFD-code FLUENT was used in all simulations. (author)

  10. Performance of the intense pulsed neutron source accelerator system

    International Nuclear Information System (INIS)

    Potts, C.; Brumwell, F.; Rauchas, A.; Stipp, V.; Volk, G.

    1983-01-01

    The Intense Pulsed Neutron Source (IPNS) facility has now been operating in a routine way for outside users since November 1, 1981. From that date through December of 1982, the accelerator system was scheduled for neutron science for 4500 hours. During this time the accelerator achieved its short-term goals by delivering about 380,000,000 pulses of beam totaling over 6 x 10 20 protons. The changes in equipment and operating practices that evolved during this period of intense running are described. The intensity related instability threshold was increased by a factor of two and the accelerator beam current has been ion source limited. Plans to increase the accelerator intensity are also described. Initial operating results with a new H - ion source are discussed

  11. The Fukushima releases: an inverse modelling approach to assess the source term by using gamma dose rate observations

    Science.gov (United States)

    Saunier, Olivier; Mathieu, Anne; Didier, Damien; Tombette, Marilyne; Quélo, Denis; Winiarek, Victor; Bocquet, Marc

    2013-04-01

    The Chernobyl nuclear accident and more recently the Fukushima accident highlighted that the largest source of error on consequences assessment is the source term estimation including the time evolution of the release rate and its distribution between radioisotopes. Inverse modelling methods have proved to be efficient to assess the source term due to accidental situation (Gudiksen, 1989, Krysta and Bocquet, 2007, Stohl et al 2011, Winiarek et al 2012). These methods combine environmental measurements and atmospheric dispersion models. They have been recently applied to the Fukushima accident. Most existing approaches are designed to use air sampling measurements (Winiarek et al, 2012) and some of them use also deposition measurements (Stohl et al, 2012, Winiarek et al, 2013). During the Fukushima accident, such measurements are far less numerous and not as well distributed within Japan than the dose rate measurements. To efficiently document the evolution of the contamination, gamma dose rate measurements were numerous, well distributed within Japan and they offered a high temporal frequency. However, dose rate data are not as easy to use as air sampling measurements and until now they were not used in inverse modelling approach. Indeed, dose rate data results from all the gamma emitters present in the ground and in the atmosphere in the vicinity of the receptor. They do not allow one to determine the isotopic composition or to distinguish the plume contribution from wet deposition. The presented approach proposes a way to use dose rate measurement in inverse modeling approach without the need of a-priori information on emissions. The method proved to be efficient and reliable when applied on the Fukushima accident. The emissions for the 8 main isotopes Xe-133, Cs-134, Cs-136, Cs-137, Ba-137m, I-131, I-132 and Te-132 have been assessed. The Daiichi power plant events (such as ventings, explosions…) known to have caused atmospheric releases are well identified in

  12. Interlaboratory study of the ion source memory effect in {sup 36}Cl accelerator mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Pavetich, Stefan, E-mail: s.pavetich@hzdr.de [Helmholtz-Zentrum Dresden-Rossendorf, Bautzner Landstraße 400, 01314 Dresden (Germany); Akhmadaliev, Shavkat [Helmholtz-Zentrum Dresden-Rossendorf, Bautzner Landstraße 400, 01314 Dresden (Germany); Arnold, Maurice; Aumaître, Georges; Bourlès, Didier [Aix-Marseille Université, CEREGE CNRS-IRD, F-13545 Aix-en-Provence (France); Buchriegler, Josef [Helmholtz-Zentrum Dresden-Rossendorf, Bautzner Landstraße 400, 01314 Dresden (Germany); University of Vienna, Faculty of Physics, VERA Laboratory, Währingerstraße 17, 1090 Vienna (Austria); Golser, Robin [University of Vienna, Faculty of Physics, VERA Laboratory, Währingerstraße 17, 1090 Vienna (Austria); Keddadouche, Karim [Aix-Marseille Université, CEREGE CNRS-IRD, F-13545 Aix-en-Provence (France); Martschini, Martin [University of Vienna, Faculty of Physics, VERA Laboratory, Währingerstraße 17, 1090 Vienna (Austria); Merchel, Silke; Rugel, Georg [Helmholtz-Zentrum Dresden-Rossendorf, Bautzner Landstraße 400, 01314 Dresden (Germany); Steier, Peter [University of Vienna, Faculty of Physics, VERA Laboratory, Währingerstraße 17, 1090 Vienna (Austria)

    2014-06-01

    Highlights: • Long-term memory effect in negative ion sources investigated for chlorine isotopes. • Interlaboratory comparison of four up-to date negative ion sources. • Ion source improvement at DREAMS for minimization of long-term memory effect. • Long-term memory effect is the limitation for precise AMS data of volatile elements. • Findings to be considered for samples with highly variable ratios of {sup 36}Cl/Cl and {sup 129}I/I. - Abstract: Understanding and minimization of contaminations in the ion source due to cross-contamination and long-term memory effect is one of the key issues for accurate accelerator mass spectrometry (AMS) measurements of volatile elements. The focus of this work is on the investigation of the long-term memory effect for the volatile element chlorine, and the minimization of this effect in the ion source of the Dresden accelerator mass spectrometry facility (DREAMS). For this purpose, one of the two original HVE ion sources at the DREAMS facility was modified, allowing the use of larger sample holders having individual target apertures. Additionally, a more open geometry was used to improve the vacuum level. To evaluate this improvement in comparison to other up-to-date ion sources, an interlaboratory comparison had been initiated. The long-term memory effect of the four Cs sputter ion sources at DREAMS (two sources: original and modified), ASTER (Accélérateur pour les Sciences de la Terre, Environnement, Risques) and VERA (Vienna Environmental Research Accelerator) had been investigated by measuring samples of natural {sup 35}Cl/{sup 37}Cl-ratio and samples highly-enriched in {sup 35}Cl ({sup 35}Cl/{sup 37}Cl ∼ 999). Besides investigating and comparing the individual levels of long-term memory, recovery time constants could be calculated. The tests show that all four sources suffer from long-term memory, but the modified DREAMS ion source showed the lowest level of contamination. The recovery times of the four ion

  13. Source term analysis for a criticality accident in metal production line glove boxes

    International Nuclear Information System (INIS)

    Nguyen, D.H.

    1991-06-01

    A recent development in criticality accident analysis is the deterministic calculations of the transport of fission products and actinides through the barriers of the physical facility. The knowledge of the redistribution of the materials inside the facility will help determine the reentry and clean-up procedures. The amount of radioactive materials released to the environment is the source term for dispersion calculations. We have used an integrated computer model to determine the release of fission products to the environment from a hypothetical criticality event in a glove box of the metal production line (MPL) at the Lawrence Livermore National Laboratory (LLNL)

  14. OpenGeoSys: An open-source initiative for numerical simulation of thermo-hydro-mechanical/chemical (THM/C) processes in porous media

    DEFF Research Database (Denmark)

    Kolditz, O.; Bauer, S.; Bilke, L.

    In this paper we describe the OpenGeoSys (OGS) project, which is a scientific open-source initiative for numerical simulation of thermo-hydro-mechanical/chemical processes in porous media. The basic concept is to provide a flexible numerical framework (using primarily the Finite Element Method (FEM...

  15. PARTITION: A program for defining the source term/consequence analysis interface in the NUREG--1150 probabilistic risk assessments

    International Nuclear Information System (INIS)

    Iman, R.L.; Helton, J.C.; Johnson, J.D.

    1990-05-01

    The individual plant analyses in the US Nuclear Regulatory Commission's reassessment of the risk from commercial nuclear power plants (NUREG-1150) consist of four parts: systems analysis, accident progression analysis, source term analysis, and consequence analysis. Careful definition of the interfaces between these parts is necessary for both information flow and computational efficiency. This document has been designed for users of the PARTITION computer program developed by the authors at Sandia National Laboratories for defining the interface between the source term analysis (performed with the XXSOR programs) and the consequence analysis (performed with the MACCS program). This report provides a tutorial that details how the interactive partitioning is performed, along with detailed information on the partitioning process. The PARTITION program was written in ANSI standard FORTRAN 77 to make the code as machine-independent (i.e., portable) as possible. 9 refs., 4 figs

  16. DESIGN OF ALTERNATIVE ENERGY SOURCES

    Directory of Open Access Journals (Sweden)

    Popa Stefania

    2013-11-01

    Full Text Available By energy sources we understand technologies and materials used to obtain various forms of energy necessary for the development of society. These sources must be in adequate quantities and be conveniently exploited in terms of technical, economic and sustainable perspective. Alternative energy uses the inherent power of natural sources like wind, tides, the sun. Alternative energy is a term used for some energy sources and energy storage technologies. Generally it indicates energies that are nontraditional and have low impact to the environment. The alternative energy term is used in contrast with the term fossil fuel according to some sources, while other sources use it with the meaning of renewable energy purposes.

  17. Technical basis for selecting radionuclide concentrations for use in Hanford tank basis for interim operation source term

    International Nuclear Information System (INIS)

    Cowley, W.L.

    1997-01-01

    This paper describes the development of a radiological source term for waste tanks at the Hanford Site Nuclear Reservation. It describes the methodology used to identify the most important radionuclides, determine appropriate concentrations, and define unit liter doses. An example of how unit liter doses are used is given

  18. Non-Fourier conduction model with thermal source term of ultra short high power pulsed laser ablation and temperature evolvement before melting

    International Nuclear Information System (INIS)

    Zhang Duanming; Li, Li; Li Zhihua; Guan Li; Tan Xinyu

    2005-01-01

    A non-Fourier conduction model with heat source term is presented to study the target temperature evolvement when the target is radiated by high power (the laser intensity is above 10 9 w/cm 2 ) and ultra short (the pulse width is less than 150 ps) pulsed laser. By Laplace transform, the analytical expression of the space- and time-dependence of temperature is derived. Then as an example of aluminum target, the target temperature evolvement is simulated. Compared with the results of Fourier conduction model and non-Fourier model without heat source term, it is found that the effect of non-Fourier conduction is notable and the heat source plays an important role during non-Fourier conduction which makes surface temperature ascending quickly with time. Meanwhile, the corresponding physical mechanism is analyzed theoretically

  19. Sanitary landfill leachate as a source of nutrients on the initial growth of sunflower plants

    Directory of Open Access Journals (Sweden)

    Francisco H. Nunes Júnior

    Full Text Available ABSTRACT The aim of this study was to evaluate the initial growth of sunflower seedlings under different concentrations of sanitary landfill leachate, considering the feasibility of its use as source of nutrients for agricultural production. Biometric and vigor variables were analyzed through the measurements of collar diameter, shoot height, number of leaves and shoot and root fresh and dry matters, from January to February 2015. The experimental design was completely randomized in a 5 x 4 factorial scheme: five leachate concentrations (0, 40, 60, 80 and 100 kg N ha-1 x four harvest periods (14, 21, 25 and 29 days after sowing, with five replicates each containing two plants. The data were subjected to analysis of variance and polynomial regression, and the results of the last harvest (29 DAS were compared by Tukey test (p ≤ 0.05. The use of sanitary landfill leachate increased all analyzed variables in sunflower plants when compared to the control plants (without leachate, especially in the treatment of 100 kg N ha-1. There was no inhibitory effect of the leachate on the initial growth of sunflower seedlings under adopted experimental conditions.

  20. INEEL Subregional Conceptual Model Report Volume 3: Summary of Existing Knowledge of Natural and Anthropogenic Influences on the Release of Contaminants to the Subsurface Environment from Waste Source Terms at the INEEL

    Energy Technology Data Exchange (ETDEWEB)

    Paul L. Wichlacz

    2003-09-01

    This source-term summary document is intended to describe the current understanding of contaminant source terms and the conceptual model for potential source-term release to the environment at the Idaho National Engineering and Environmental Laboratory (INEEL), as presented in published INEEL reports. The document presents a generalized conceptual model of the sources of contamination and describes the general categories of source terms, primary waste forms, and factors that affect the release of contaminants from the waste form into the vadose zone and Snake River Plain Aquifer. Where the information has previously been published and is readily available, summaries of the inventory of contaminants are also included. Uncertainties that affect the estimation of the source term release are also discussed where they have been identified by the Source Term Technical Advisory Group. Areas in which additional information are needed (i.e., research needs) are also identified.

  1. Mass carbon monoxide poisoning at an ice-hockey game: initial approach and long-term follow-up.

    Science.gov (United States)

    Mortelmans, Luc J M; Populaire, Jacques; Desruelles, Didier; Sabbe, Marc B

    2013-12-01

    A mass carbon monoxide (CO) intoxication during an ice-hockey game is described. Two hundred and thirty-five patients were seen in different hospitals, 88 of them the same night at the nearby emergency department. To evaluate long-term implications and to identify relevant indicators, a follow-up study was organized 1 year after the incident. Apart from the file data from the emergency departments, a 1-year follow-up mailing was sent to all patients. One hundred and ninety-one patients returned their questionnaire (86%). The mean age of the patients was 28 years, with 61% men. The mean carboxyhaemoglobin (COHb) was 9.9%. COHb levels were significantly higher for individuals on the ice (referee, players and maintenance personnel). There was a significant relationship with the initial presence of dizziness, fatigue and the COHb level. Headache, abdominal pain, nausea and vomiting were not significantly related to the COHb levels. The relationship between symptoms and CO level, however, should be interpreted with caution as there was a wide range between exposure and blood tests. 5.2% of patients had residual complaints, all including headache, with a significant higher incidence with high COHb levels. Only two patients had an abnormal neurological control (one slightly disturbed electroencephalography and one persistent encephalopathic complaint). Work incapacity was also significantly related to COHb levels. CO mass poisonings remain a risk in indoor sporting events. Although it causes an acute mass casualty incident, it is limited in time and delayed problems are scarce. Symptomatology is a poor tool for triage. The best prevention is the use of nonmineral energy sources such as for example electricity.

  2. The uranium source-term mineralogy and geochemistry at the Broubster natural analogue site, Caithness

    International Nuclear Information System (INIS)

    Milodowski, A.E.; Pearce, J.M.; Basham, I.R.; Hyslop, E.K.

    1991-01-01

    The British Geological Survey (BGS) has been conducting a coordinated research programme at the Broubster natural analogue site in Caithness, north Scotland. This work on a natural radioactive geochemical system has been carried out with the aim of improving our confidence in using predictive models of radionuclide migration in the geosphere. This report is one of a series being produced and it concentrates on the mineralogical characterization of the uranium distribution in the limestone unit considered as the 'source-term' in the natural analogue model

  3. Study of the source term of radiation of the CDTN GE-PET trace 8 cyclotron with the MCNPX code

    Energy Technology Data Exchange (ETDEWEB)

    Benavente C, J. A.; Lacerda, M. A. S.; Fonseca, T. C. F.; Da Silva, T. A. [Centro de Desenvolvimento da Tecnologia Nuclear / CNEN, Av. Pte. Antonio Carlos 6627, 31270-901 Belo Horizonte, Minas Gerais (Brazil); Vega C, H. R., E-mail: jhonnybenavente@gmail.com [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98068 Zacatecas, Zac. (Mexico)

    2015-10-15

    Full text: The knowledge of the neutron spectra in a PET cyclotron is important for the optimization of radiation protection of the workers and individuals of the public. The main objective of this work is to study the source term of radiation of the GE-PET trace 8 cyclotron of the Development Center of Nuclear Technology (CDTN/CNEN) using computer simulation by the Monte Carlo method. The MCNPX version 2.7 code was used to calculate the flux of neutrons produced from the interaction of the primary proton beam with the target body and other cyclotron components, during 18F production. The estimate of the source term and the corresponding radiation field was performed from the bombardment of a H{sub 2}{sup 18}O target with protons of 75 μA current and 16.5 MeV of energy. The values of the simulated fluxes were compared with those reported by the accelerator manufacturer (GE Health care Company). Results showed that the fluxes estimated with the MCNPX codes were about 70% lower than the reported by the manufacturer. The mean energies of the neutrons were also different of that reported by GE Health Care. It is recommended to investigate other cross sections data and the use of physical models of the code itself for a complete characterization of the source term of radiation. (Author)

  4. Dual-source CT cardiac imaging: initial experience

    International Nuclear Information System (INIS)

    Johnson, Thorsten R.C.; Nikolaou, Konstantin; Wintersperger, Bernd J.; Rist, Carsten; Buhmann, Sonja; Reiser, Maximilian F.; Becker, Christoph R.; Leber, Alexander W.; Ziegler, Franz von; Knez, Andreas

    2006-01-01

    The relation of heart rate and image quality in the depiction of coronary arteries, heart valves and myocardium was assessed on a dual-source computed tomography system (DSCT). Coronary CT angiography was performed on a DSCT (Somatom Definition, Siemens) with high concentration contrast media (Iopromide, Ultravist 370, Schering) in 24 patients with heart rates between 44 and 92 beats per minute. Images were reconstructed over the whole cardiac cycle in 10% steps. Two readers independently assessed the image quality with regard to the diagnostic evaluation of right and left coronary artery, heart valves and left ventricular myocardium for the assessment of vessel wall changes, coronary stenoses, valve morphology and function and ventricular function on a three point grading scale. The image quality ratings at the optimal reconstruction interval were 1.24±0.42 for the right and 1.09±0.27 for the left coronary artery. A reconstruction of diagnostic systolic and diastolic images is possible for a wide range of heart rates, allowing also a functional evaluation of valves and myocardium. Dual-source CT offers very robust diagnostic image quality in a wide range of heart rates. The high temporal resolution now also makes a functional evaluation of the heart valves and myocardium possible. (orig.)

  5. Methodology for the calculation of source terms related to irradiated fuel accumulated away from nuclear power plants

    International Nuclear Information System (INIS)

    Lima Filho, R.M.; Oliveira, L.F.S. de

    1984-01-01

    A general method for the calculation of the time evolution of source terms related to irradiated fuel is presented. Some applications are discussed which indicated that the method can provide important informations for the engineering design and safety analysis of a temporary storage facility of irradiated fuel elements. (Author) [pt

  6. On the sequence of core-melt accidents: Fission product release, source terms and Chernobyl release

    Energy Technology Data Exchange (ETDEWEB)

    Albrecht, H

    1986-01-01

    There is a sketch of our ideas on the course of a core melt-out accident in a PWR. There is then a survey of the most important results on fission product release, which were obtained by experiments on the SASCHA melt-out plant. The 3rd part considers questions which are important for determining source terms for the environment and the last part contains some considerations on radioactivity release from the Chernobyl reactor.

  7. Identifying Patterns in the Weather of Europe for Source Term Estimation

    Science.gov (United States)

    Klampanos, Iraklis; Pappas, Charalambos; Andronopoulos, Spyros; Davvetas, Athanasios; Ikonomopoulos, Andreas; Karkaletsis, Vangelis

    2017-04-01

    During emergencies that involve the release of hazardous substances into the atmosphere the potential health effects on the human population and the environment are of primary concern. Such events have occurred in the past, most notably involving radioactive and toxic substances. Examples of radioactive release events include the Chernobyl accident in 1986, as well as the more recent Fukushima Daiichi accident in 2011. Often, the release of dangerous substances in the atmosphere is detected at locations different from the release origin. The objective of this work is the rapid estimation of such unknown sources shortly after the detection of dangerous substances in the atmosphere, with an initial focus on nuclear or radiological releases. Typically, after the detection of a radioactive substance in the atmosphere indicating the occurrence of an unknown release, the source location is estimated via inverse modelling. However, depending on factors such as the spatial resolution desired, traditional inverse modelling can be computationally time-consuming. This is especially true for cases where complex topography and weather conditions are involved and can therefore be problematic when timing is critical. Making use of machine learning techniques and the Big Data Europe platform1, our approach moves the bulk of the computation before any such event taking place, therefore allowing for rapid initial, albeit rougher, estimations regarding the source location. Our proposed approach is based on the automatic identification of weather patterns within the European continent. Identifying weather patterns has long been an active research field. Our case is differentiated by the fact that it focuses on plume dispersion patterns and these meteorological variables that affect dispersion the most. For a small set of recurrent weather patterns, we simulate hypothetical radioactive releases from a pre-known set of nuclear reactor locations and for different substance and temporal

  8. Osmium Isotopic Evolution of the Mantle Sources of Precambrian Ultramafic Rocks

    Science.gov (United States)

    Gangopadhyay, A.; Walker, R. J.

    2006-12-01

    The Os isotopic composition of the modern mantle, as recorded collectively by ocean island basalts, mid- oceanic ridge basalts (MORB) and abyssal peridotites, is evidently highly heterogeneous (γ Os(I) ranging from +25). One important question, therefore, is how and when the Earth's mantle developed such large-scale Os isotopic heterogeneities. Previous Os isotopic studies of ancient ultramafic systems, including komatiites and picrites, have shown that the Os isotopic heterogeneity of the terrestrial mantle can be traced as far back as the late-Archean (~ 2.7-2.8 Ga). This observation is based on the initial Os isotopic ratios obtained for the mantle sources of some of the ancient ultramafic rocks determined through analyses of numerous Os-rich whole-rock and/or mineral samples. In some cases, the closed-system behavior of these ancient ultramafic rocks was demonstrated via the generation of isochrons of precise ages, consistent with those obtained from other radiogenic isotopic systems. Thus, a compilation of the published initial ^{187}Os/^{188}Os ratios reported for the mantle sources of komatiitic and picritic rocks is now possible that covers a large range of geologic time spanning from the Mesozoic (ca. 89 Ma Gorgona komatiites) to the Mid-Archean (e.g., ca. 3.3 Ga Commondale komatiites), which provides a comprehensive picture of the Os isotopic evolution of their mantle sources through geologic time. Several Precambrian komatiite/picrite systems are characterized by suprachondritic initial ^{187}Os/^{188}Os ratios (e.g., Belingwe, Kostomuksha, Pechenga). Such long-term enrichments in ^{187}Os of the mantle sources for these rocks may be explained via recycling of old mafic oceanic crust or incorporation of putative suprachondritic outer core materials entrained into their mantle sources. The relative importance of the two processes for some modern mantle-derived systems (e.g., Hawaiian picrites) is an issue of substantial debate. Importantly, however, the

  9. Development of Coupled Interface System between the FADAS Code and a Source-term Evaluation Code XSOR for CANDU Reactors

    International Nuclear Information System (INIS)

    Son, Han Seong; Song, Deok Yong; Kim, Ma Woong; Shin, Hyeong Ki; Lee, Sang Kyu; Kim, Hyun Koon

    2006-01-01

    An accident prevention system is essential to the industrial security of nuclear industry. Thus, the more effective accident prevention system will be helpful to promote safety culture as well as to acquire public acceptance for nuclear power industry. The FADAS(Following Accident Dose Assessment System) which is a part of the Computerized Advisory System for a Radiological Emergency (CARE) system in KINS is used for the prevention against nuclear accident. In order to enhance the FADAS system more effective for CANDU reactors, it is necessary to develop the various accident scenarios and reliable database of source terms. This study introduces the construction of the coupled interface system between the FADAS and the source-term evaluation code aimed to improve the applicability of the CANDU Integrated Safety Analysis System (CISAS) for CANDU reactors

  10. Serum thiamine level during the initiation term of hemodialysis

    Directory of Open Access Journals (Sweden)

    Shuji Ono

    2012-06-01

    Although water-soluble vitamins such as thiamine are lost during dialysis session, serum thiamine level tended to restore spontaneously during the hospitalization (25.47±10.07 vs. 27.44±11.37, pre HD value, p=0.09. A three months-follow up measurement after initiation of HD, which is now in progress (so far n=3, revealed increase of serum thiamine level in all patients (35.33±7.37 ng/ml. It may reflect the improvement of nutritional status after the initiation of HD, and suggests the loss of thiamine by HD procedure can be covered.

  11. Distributed source term analysis, a new approach to nuclear material inventory verification

    CERN Document Server

    Beddingfield, D H

    2002-01-01

    The Distributed Source-Term Analysis (DSTA) technique is a new approach to measuring in-process material holdup that is a significant departure from traditional hold-up measurement methodology. The DSTA method is a means of determining the mass of nuclear material within a large, diffuse, volume using passive neutron counting. The DSTA method is a more efficient approach than traditional methods of holdup measurement and inventory verification. The time spent in performing DSTA measurement and analysis is a fraction of that required by traditional techniques. The error ascribed to a DSTA survey result is generally less than that from traditional methods. Also, the negative bias ascribed to gamma-ray methods is greatly diminished because the DSTA method uses neutrons which are more penetrating than gamma-rays.

  12. Distributed source term analysis, a new approach to nuclear material inventory verification

    International Nuclear Information System (INIS)

    Beddingfield, D.H.; Menlove, H.O.

    2002-01-01

    The Distributed Source-Term Analysis (DSTA) technique is a new approach to measuring in-process material holdup that is a significant departure from traditional hold-up measurement methodology. The DSTA method is a means of determining the mass of nuclear material within a large, diffuse, volume using passive neutron counting. The DSTA method is a more efficient approach than traditional methods of holdup measurement and inventory verification. The time spent in performing DSTA measurement and analysis is a fraction of that required by traditional techniques. The error ascribed to a DSTA survey result is generally less than that from traditional methods. Also, the negative bias ascribed to γ-ray methods is greatly diminished because the DSTA method uses neutrons which are more penetrating than γ-rays

  13. Predicted radionuclide release from marine reactors dumped in the Kara Sea. Report of the source term working group of the international arctic seas assessment project (IASAP)

    International Nuclear Information System (INIS)

    1997-04-01

    The present report summarizes the work carried out by the Source Term Working Group of IASAP during 1994-1996. The report is based on the studies concerning the initial and current radionuclide inventories, operational history and construction of the reactors carried out by Y. Sivintsev of the Russian Research Center ''Kurchatov Institute'', Moscow and E. Yefimov of the Institute of Physics and Power Engineering, Obninsk, Russian Federation. The working group convened five times and evaluated the results of the studies and developed models for prediction of potential releases to the environment. The calculations were carried out at the Royal Naval College, Greenwich, UK, by N. Lynn, J. Warden and S. Timms and at the Lawrence Livermore National Laboratory, California, USA, by M. Mount. 31 refs, 36 figs, 18 tabs

  14. Source Term Analysis for the Nuclear Power Station Goesgen-Daeniken; Quelltermanalysen fuer das Kernkraftwerk Goesgen-Daeniken

    Energy Technology Data Exchange (ETDEWEB)

    Hosemann, J.P.; Megaritis, G.; Guentay, S.; Hirschmann, H.; Luebbesmeyer, D.; Lieber, K.; Jaeckel, B.; Birchley, J.; Duijvestijn, G

    2001-08-01

    Analyses are performed for three accident scenarios postulated to occur in the Goesgen Nuclear Power Plant, a 900 MWe Pressurised Water Reactor of Siemens design. The scenarios investigated comprise a Station Blackout and two separate cases of small break loss-of-coolant accident which lead, respectively, to high, intermediate and low pressure conditions in the reactor system. In each case the accident assumptions are highly pessimistic, so that the sequences span a large range of plant states and a damage phenomena. Thus the plant is evaluated for a diversity of potential safety challenges. A suite of analysis tools are used to examine the reactor coolant system response, the core heat-up, melting, fission product release from the reactor system, the transport and chemical behaviour of those fission products in the containment building, and the release of radioactivity (source term) to the environment. Comparison with reference values used by the licensing authority shows that the use of modern analysis tools and current knowledge can provide substantial reduction in the estimated source term. Of particular interest are insights gained from the analyses which indicate opportunities for operators to reduce or forestall the release. (author)

  15. Neutron and photon measurements through concrete from a 15 GeV electron beam on a target-comparison with models and calculations. [Intermediate energy source term, Monte Carlo code

    Energy Technology Data Exchange (ETDEWEB)

    Jenkins, T M [Stanford Linear Accelerator Center, CA (USA)

    1979-02-15

    Measurements of neutron and photon dose equivalents from a 15 GeV electron beam striking an iron target inside a scale model of a PEP IR hall are described, and compared with analytic-empirical calculations and with the Monte Carlo code, MORSE. The MORSE code is able to predict both absolute neutron and photon dose equivalents for geometries where the shield is relatively thin, but fails as the shield thickness is increased. An intermediate energy source term is postulated for analytic-empirical neutron shielding calculations to go along with the giant resonance and high energy terms, and a new source term due to neutron capture is postulated for analytic-empirical photon shielding calculations. The source strengths for each energy source term, and each type, are given from analysis of the measurements.

  16. A Reappraisal of Women’s Health Initiative Estrogen-Alone Trial: Long-Term Outcomes in Women 50–59 Years of Age

    Directory of Open Access Journals (Sweden)

    Eric Roehm

    2015-01-01

    Full Text Available The Women’s Health Initiative (WHI Estrogen-Alone Trial randomized postmenopausal women, 50 to 79 years of age, with prior hysterectomy, to conjugated equine estrogens (CEE or placebo with a 5.9-year median duration of CEE use. In 2013, the WHI published outcomes for additional extended follow-up. Reported here for the first time is an analysis of the number needed to treat with CEE rather than placebo for younger women (50–59 years to prevent an adverse long-term outcome. For every 76 women randomized to CEE at 50–59 years, one less myocardial infarction occurred during the 13-year cumulative long-term follow-up. For every 37 women randomized to CEE at 50–59 years, one less woman experienced a global index endpoint (including coronary heart disease, invasive breast cancer, stroke, pulmonary embolism, colorectal cancer, hip fracture, and death during the 13-year follow-up. Younger women (50–59 years, compared to older women, had more favorable cumulative long-term outcomes for MI and global index. Though a subgroup analysis is not an adequate basis for making primary prevention guideline recommendations, the WHI Estrogen-Alone Trial outcomes strongly suggest that a similar course of estrogen initiated at 50–59 years in postmenopausal women with prior hysterectomy results in significant long-term health benefit.

  17. The Problem of Late ART initiation in Sub-Saharan Africa: A Transient Aspect of Scale-up or a Long-term Phenomenon?

    Science.gov (United States)

    Lahuerta, Maria; Ue, Frances; Hoffman, Susie; Elul, Batya; Kulkarni, Sarah Gorrell; Wu, Yingfeng; Nuwagaba-Biribonwoha, Harriet; Remien, Robert H.; Sadr, Wafaa El; Nash, Denis

    2013-01-01

    Efforts to scale-up HIV care and treatment have been successful at initiating large numbers of patients onto antiretroviral therapy (ART), although persistent challenges remain to optimizing scale-up effectiveness in both resource-rich and resource-limited settings. Among the most important are very high rates of ART initiation in the advanced stages of HIV disease, which in turn drive morbidity, mortality, and onward transmission of HIV. With a focus on sub-Saharan Africa, this review article presents a conceptual framework for a broader discussion of the persistent problem of late ART initiation, including a need for more focus on the upstream precursors (late HIV diagnosis and late enrollment into HIV care) and their determinants. Without additional research and identification of multilevel interventions that successfully promote earlier initiation of ART, the problem of late ART initiation will persist, significantly undermining the long-term impact of HIV care scale-up on reducing mortality and controlling the HIV epidemic. PMID:23377739

  18. Evaluation Plan on In-vessel Source Term in PGSFR

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Seung Won; Ha, Kwi-Seok; Ahn, Sang June; Lee, Kwi Lim; Jeong, Taekyeong [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-10-15

    This strategy requires nuclear plants to have features that prevent radionuclide release and multiple barriers to the escape from the plants of any radionuclides that are released despite preventive measures. Considerations of the ability to prevent and mitigate release of radionuclides arise at numerous places in the safety regulations of nuclear plants. The effectiveness of mitigative capabilities in nuclear plants is subject to quantitative analysis. The radionuclide input to these quantitative analyses of effectiveness is the Source Term (ST). All features of the composition, magnitude, timing, chemical form and physical form of accidental radionuclide release constitute the ST. Also, ST is defined as the release of radionuclides from the fuel and coolant into the containment, and subsequently to the environment. The in-vessel STs of PGSFR will be estimated using the methodology of ANL-ART-38 report in additional to 4S methodology. The in-vessel STs are calculated through several phases: The inventory of each radionuclide is calculated by ORIGEN-2 code using the realistic burnup conditions. ST in the release from the core to primary sodium is calculated by using the assumption of ANL methodology. Lastly, ST in the release from the primary sodium to cover gas space is calculated by using equation and experimental materials.

  19. Evaluation Plan on In-vessel Source Term in PGSFR

    International Nuclear Information System (INIS)

    Lee, Seung Won; Ha, Kwi-Seok; Ahn, Sang June; Lee, Kwi Lim; Jeong, Taekyeong

    2016-01-01

    This strategy requires nuclear plants to have features that prevent radionuclide release and multiple barriers to the escape from the plants of any radionuclides that are released despite preventive measures. Considerations of the ability to prevent and mitigate release of radionuclides arise at numerous places in the safety regulations of nuclear plants. The effectiveness of mitigative capabilities in nuclear plants is subject to quantitative analysis. The radionuclide input to these quantitative analyses of effectiveness is the Source Term (ST). All features of the composition, magnitude, timing, chemical form and physical form of accidental radionuclide release constitute the ST. Also, ST is defined as the release of radionuclides from the fuel and coolant into the containment, and subsequently to the environment. The in-vessel STs of PGSFR will be estimated using the methodology of ANL-ART-38 report in additional to 4S methodology. The in-vessel STs are calculated through several phases: The inventory of each radionuclide is calculated by ORIGEN-2 code using the realistic burnup conditions. ST in the release from the core to primary sodium is calculated by using the assumption of ANL methodology. Lastly, ST in the release from the primary sodium to cover gas space is calculated by using equation and experimental materials

  20. Verification test calculations for the Source Term Code Package

    International Nuclear Information System (INIS)

    Denning, R.S.; Wooton, R.O.; Alexander, C.A.; Curtis, L.A.; Cybulskis, P.; Gieseke, J.A.; Jordan, H.; Lee, K.W.; Nicolosi, S.L.

    1986-07-01

    The purpose of this report is to demonstrate the reasonableness of the Source Term Code Package (STCP) results. Hand calculations have been performed spanning a wide variety of phenomena within the context of a single accident sequence, a loss of all ac power with late containment failure, in the Peach Bottom (BWR) plant, and compared with STCP results. The report identifies some of the limitations of the hand calculation effort. The processes involved in a core meltdown accident are complex and coupled. Hand calculations by their nature must deal with gross simplifications of these processes. Their greatest strength is as an indicator that a computer code contains an error, for example that it doesn't satisfy basic conservation laws, rather than in showing the analysis accurately represents reality. Hand calculations are an important element of verification but they do not satisfy the need for code validation. The code validation program for the STCP is a separate effort. In general the hand calculation results show that models used in the STCP codes (e.g., MARCH, TRAP-MELT, VANESA) obey basic conservation laws and produce reasonable results. The degree of agreement and significance of the comparisons differ among the models evaluated. 20 figs., 26 tabs

  1. Short-Term Memory Stages in Sign vs. Speech: The Source of the Serial Span Discrepancy

    OpenAIRE

    Hall, Matthew L.

    2011-01-01

    Speakers generally outperform signers when asked to recall a list of unrelated verbal items. This phenomenon is well established, but its source has remained unclear. In this study, we evaluate the relative contribution of the three main processing stages of short-term memory – perception, encoding, and recall – in this effect. The present study factorially manipulates whether American Sign Language (ASL) or English was used for perception, memory encoding, and recall in hearing ASL-English b...

  2. Short-term memory stages in sign vs. speech: The source of the serial span discrepancy

    OpenAIRE

    Hall, Matthew L.; Bavelier, Daphné

    2011-01-01

    Speakers generally outperform signers when asked to recall a list of unrelated verbal items. This phenomenon is well established, but its source has remained unclear. In this study, we evaluate the relative contribution of the three main processing stages of short-term memory – perception, encoding, and recall – in this effect. The present study factorially manipulates whether American Sign Language (ASL) or English is used for perception, memory encoding, and recall in hearing ASL-English bi...

  3. Design and Formative Evaluation of the Policy Liaison Initiative: A Long-Term Knowledge Translation Strategy to Encourage and Support the Use of Cochrane Systematic Reviews for Informing

    Science.gov (United States)

    Brennan, Sue E.; Cumpston, Miranda; Misso, Marie L.; McDonald, Steve; Murphy, Matthew J.; Green, Sally E.

    2016-01-01

    The Policy Liaison Initiative (PLI) is a long-term knowledge translation initiative designed to support the use of Cochrane systematic reviews in health policy. A joint initiative between the Australasian Cochrane Centre and Australian Government Department of Health and Ageing, the PLI includes: 1) a community of practice for evidence-informed…

  4. Defense Acquisition Initiatives Review: An Assessment of Extant Initiatives

    National Research Council Canada - National Science Library

    Porter, Gene; Berteau, David; Christle, Gary; Mandelbaum, Jay; Diehl, Richard

    2005-01-01

    ...) to identify and analyze a subset of initiatives that the team finds to have potential for near term management emphasis that could provide visible improvements to the much criticized Defense acquisition system...

  5. Advances in automated noise data acquisition and noise source modeling for power reactors

    International Nuclear Information System (INIS)

    Clapp, N.E. Jr.; Kryter, R.C.; Sweeney, F.J.; Renier, J.A.

    1981-01-01

    A newly expanded program, directed toward achieving a better appreciation of both the strengths and limitations of on-line, noise-based, long-term surveillance programs for nuclear reactors, is described. Initial results in the complementary experimental (acquisition and automated screening of noise signatures) and theoretical (stochastic modeling of likely noise sources) areas of investigation are given

  6. How Long Does it Take to Initiate a Child on Long-Term Invasive Ventilation? Results From A Canadian Pediatric Home Ventilation Program

    Directory of Open Access Journals (Sweden)

    Reshma Amin

    2015-01-01

    Full Text Available OBJECTIVE: To assess the length of stay required to initiate long-term invasive ventilation at the authors’ institution, which would inform future interventional strategies to streamline the in-hospital stay for these families.

  7. Dynamical initial-state model for relativistic heavy-ion collisions

    Science.gov (United States)

    Shen, Chun; Schenke, Björn

    2018-02-01

    We present a fully three-dimensional model providing initial conditions for energy and net-baryon density distributions in heavy-ion collisions at arbitrary collision energy. The model includes the dynamical deceleration of participating nucleons or valence quarks, depending on the implementation. The duration of the deceleration continues until the string spanned between colliding participants is assumed to thermalize, which is either after a fixed proper time, or a fluctuating time depending on sampled final rapidities. Energy is deposited in space time along the string, which in general will span a range of space-time rapidities and proper times. We study various observables obtained directly from the initial-state model, including net-baryon rapidity distributions, two-particle rapidity correlations, as well as the rapidity decorrelation of the transverse geometry. Their dependence on the model implementation and parameter values is investigated. We also present the implementation of the model with 3+1-dimensional hydrodynamics, which involves the addition of source terms that deposit energy and net-baryon densities produced by the initial-state model at proper times greater than the initial time for the hydrodynamic simulation.

  8. Jet flow analysis of liquid poison injection in a CANDU reactor using source term

    International Nuclear Information System (INIS)

    Chae, Kyung Myung; Choi, Hang Bok; Rhee, Bo Wook

    2001-01-01

    For the performance analysis of Canadian deuterium uranium (CANDU) reactor shutdown system number 2 (SDS2), a computational fluid dynamics model of poison jet flow has been developed to estimate the flow field and poison concentration formed inside the CANDU reactor calandria. As the ratio of calandria shell radius over injection nozzle hole diameter is so large (1055), it is impractical to develop a full-size model encompassing the whole calandria shell. In order to reduce the model to a manageable size, a quarter of one-pitch length segment of the shell was modeled using symmetric nature of the jet; and the injected jet was treated as a source term to avoid the modeling difficulty caused by the big difference of the hole sizes. For the analysis of an actual CANDU-6 SDS2 poison injection, the grid structure was determined based on the results of two-dimensional real- and source-jet simulations. The maximum injection velocity of the liquid poison is 27.8 m/s and the mass fraction of the poison is 8000 ppm (mg/kg). The simulation results have shown well-established jet flow field. In general, the jet develops narrowly at first but stretches rapidly. Then, the flow recirculates a little in r-x plane, while it recirculates largely in r-θ plane. As the time goes on, the adjacent jets contact each other and form a wavy front such that the whole jet develops in a plate form. his study has shown that the source term model can be effectively used for the analysis of the poison injection and the simulation result of the CANDU reactor is consistent with the model currently being used for the safety analysis. In the future, it is strongly recommended to analyze the transient (from helium tank to injection nozzle hole) of the poison injection by applying Bernoulli equation with real boundary conditions

  9. Quality assurance of HDR 192Ir sources using a Fricke dosimeter.

    Science.gov (United States)

    Austerlitz, C; Mota, H; Almeida, C E; Allison, R; Sibata, C

    2007-04-01

    A prototype of a Fricke dosimetry system consisting of a 15 x 15 x 15 cm3 water phantom made of Plexiglas and a 11.3-ml Pyrex balloon fitted with a 0.2 cm thick Pyrex sleeve in its center was created to assess source strength and treatment planning algorithms for use in high dose rate (HDR) 192Ir afterloading units. In routine operation, the radioactive source is positioned at the end of a sleeve, which coincides with the center of the spherical balloon that is filled with Fricke solution, so that the solution is nearly isotropically irradiated. The Fricke system was calibrated in terms of source strength against a reference well-type ionization chamber, and in terms of radial dose by means of an existing algorithm from the HDR's treatment planning system. Because the system is based on the Fricke dosimeter itself, for a given type and model of 192Ir source, the system needs initial calibration but no recalibration. The results from measurements made over a 10 month period, including source decay and source substitutions, have shown the feasibility of using such a system for quality control (QC) of HDR afterloading equipment, including both the source activity and treatment planning parameters. The benefit of a large scale production and the use of this device for clinical HDR QC audits via mail are also discussed.

  10. Radon measurements: the sources of uncertainties

    International Nuclear Information System (INIS)

    Zhukovsky, Michael; Onischenko, Alexandra; Bastrikov, Vladislav

    2008-01-01

    Full text: Radon measurements are quite complicated process and the correct estimation of uncertainties is very important. The sources of uncertainties for grab sampling, short term measurements (charcoal canisters), long term measurements (track detectors) and retrospective measurements (surface traps) are analyzed. The main sources of uncertainties for grab sampling measurements are: systematic bias of reference equipment; random Poisson and non-Poisson errors during calibration; random Poisson and non-Poisson errors during measurements. These sources are also common both for short term measurements (charcoal canisters) and long term measurements (track detectors). Usually during the calibration the high radon concentrations are used (1-5 kBq/m 3 ) and the Poisson random error rarely exceed some percents. Nevertheless the dispersion of measured values even during the calibration usually exceeds the Poisson dispersion expected on the basis of counting statistic. The origins of such non-Poisson random errors during calibration are different for different kinds of instrumental measurements. At present not all sources of non-Poisson random errors are trustworthy identified. The initial calibration accuracy of working devices rarely exceeds the value 20%. The real radon concentrations usually are in the range from some tens to some hundreds Becquerel per cubic meter and for low radon levels Poisson random error can reach up to 20%. The random non-Poisson errors and residual systematic biases are depends on the kind of measurement technique and the environmental conditions during radon measurements. For charcoal canisters there are additional sources of the measurement errors due to influence of air humidity and the variations of radon concentration during the canister exposure. The accuracy of long term measurements by track detectors will depend on the quality of chemical etching after exposure and the influence of season radon variations. The main sources of

  11. Unclassified Source Term and Radionuclide Data for Corrective Action Unit 98: Frenchman Flat Nevada Test Site, Nevada

    International Nuclear Information System (INIS)

    Farnham, Irene

    2005-01-01

    Frenchman Flat is one of several areas of the Nevada Test Site (NTS) used for underground nuclear testing (Figure 1-1). These nuclear tests resulted in groundwater contamination in the vicinity of the underground test areas. As a result, the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO) is currently conducting a corrective action investigation (CAI) of the Frenchman Flat underground test areas. Since 1996, the Nevada Division of Environmental Protection (NDEP) has regulated NNSA/NSO corrective actions through the ''Federal Facility Agreement and Consent Order'' ([FFACO], 1996). Appendix VI of the FFACO agreement, ''Corrective Action Strategy'', was revised on December 7, 2000, and describes the processes that will be used to complete corrective actions, including those in the Underground Test Area (UGTA) Project. The individual locations covered by the agreement are known as corrective action sites (CASs), which are grouped into corrective action units (CAUs). The UGTA CASs are grouped geographically into five CAUs: Frenchman Flat, Central Pahute Mesa, Western Pahute Mesa, Yucca Flat/Climax Mine, and Rainier Mesa/Shoshone Mountain (Figure 1-1). These CAUs have distinctly different contaminant source, geologic, and hydrogeologic characteristics related to their location (FFACO, 1996). The Frenchman Flat CAU consists of 10 CASs located in the northern part of Area 5 and the southern part of Area 11 (Figure 1-1). This report documents the evaluation of the information and data available on the unclassified source term and radionuclide contamination for Frenchman Flat, CAU 98. The methodology used to estimate hydrologic source terms (HSTs) for the Frenchman Flat CAU is also documented. The HST of an underground nuclear test is the portion of the total inventory of radionuclides that is released over time into the groundwater following the test. The total residual inventory of radionuclides associated with one or

  12. Source modelling of train noise - Literature review and some initial measurements

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Xuetao; Jonasson, Hans; Holmberg, Kjell

    2000-07-01

    A literature review of source modelling of railway noise is reported. Measurements on a special test rig at Surahammar and on the new railway line between Arlanda and Stockholm City are reported and analyzed. In the analysis the train is modelled as a number of point sources with or without directivity and each source is combined with analytical sound propagation theory to predict the sound propagation pattern best fitting the measured data. Wheel/rail rolling noise is considered to be the most important noise source. The rolling noise can be modelled as an array of moving point sources, which have a dipole-like horizontal directivity and some kind of vertical directivity. In general it is necessary to distribute the point sources on several heights. Based on our model analysis the source heights for the rolling noise should be below the wheel axles and the most important height is about a quarter of wheel diameter above the railheads. When train speeds are greater than 250 km/h aerodynamic noise will become important and even dominant. It may be important for low frequency components only if the train speed is less than 220 km/h. Little data are available for these cases. It is believed that aerodynamic noise has dipole-like directivity. Its spectrum depends on many factors: speed, railway system, type of train, bogies, wheels, pantograph, presence of barriers and even weather conditions. Other sources such as fans, engine, transmission and carriage bodies are at most second order noise sources, but for trains with a diesel locomotive engine the engine noise will be dominant if train speeds are less than about 100 km/h. The Nord 2000 comprehensive model for sound propagation outdoors, together with the source model that is based on the understandings above, can suitably handle the problems of railway noise propagation in one-third octave bands although there are still problems left to be solved.

  13. Diagnosis and prognosis of the source term by the French Safety Institut during an emergency on a PWR

    International Nuclear Information System (INIS)

    Chauliac, C.; Janot, L.; Jouzier, A.; Rague, B.

    1992-01-01

    The French approach for the diagnosis and the prognosis of the source term during an accident on a PWR is presented and the tools which have been developed to implement this approach at the Institute for Nuclear Protection and Safety (IPSN) are described. (author). 2 refs, 3 figs

  14. Nonradioactive Environmental Emissions Chemical Source Term for the Double-Shell Tank (DST) Vapor Space During Waste Retrieval Operations

    International Nuclear Information System (INIS)

    MAY, T.H.

    2000-01-01

    A nonradioactive chemical vapor space source term for tanks on the Phase 1 and the extended Phase 1 delivery, storage, and disposal mission was determined. Operations modeled included mixer pump operation and DST waste transfers. Concentrations of ammonia, specific volatile organic compounds, and quantitative volumes of aerosols were estimated

  15. Asymptotically and exactly energy balanced augmented flux-ADER schemes with application to hyperbolic conservation laws with geometric source terms

    Science.gov (United States)

    Navas-Montilla, A.; Murillo, J.

    2016-07-01

    In this work, an arbitrary order HLL-type numerical scheme is constructed using the flux-ADER methodology. The proposed scheme is based on an augmented Derivative Riemann solver that was used for the first time in Navas-Montilla and Murillo (2015) [1]. Such solver, hereafter referred to as Flux-Source (FS) solver, was conceived as a high order extension of the augmented Roe solver and led to the generation of a novel numerical scheme called AR-ADER scheme. Here, we provide a general definition of the FS solver independently of the Riemann solver used in it. Moreover, a simplified version of the solver, referred to as Linearized-Flux-Source (LFS) solver, is presented. This novel version of the FS solver allows to compute the solution without requiring reconstruction of derivatives of the fluxes, nevertheless some drawbacks are evidenced. In contrast to other previously defined Derivative Riemann solvers, the proposed FS and LFS solvers take into account the presence of the source term in the resolution of the Derivative Riemann Problem (DRP), which is of particular interest when dealing with geometric source terms. When applied to the shallow water equations, the proposed HLLS-ADER and AR-ADER schemes can be constructed to fulfill the exactly well-balanced property, showing that an arbitrary quadrature of the integral of the source inside the cell does not ensure energy balanced solutions. As a result of this work, energy balanced flux-ADER schemes that provide the exact solution for steady cases and that converge to the exact solution with arbitrary order for transient cases are constructed.

  16. The influence of the first non-singular stress terms on crack initiation direction in an orthotropic bi-material plate

    Czech Academy of Sciences Publication Activity Database

    Klusák, Jan; Hrstka, M.; Profant, T.; Krepl, Ondřej; Ševeček, O.; Kotoul, M.

    2014-01-01

    Roč. 71, JUN (2014), s. 67-75 ISSN 0167-8442 R&D Projects: GA MŠk(CZ) ED1.1.00/02.0068; GA ČR GA14-11234S Institutional support: RVO:68081723 Keywords : Bi-material notch * Crack initiation direction * Non-singular stress term * Generalized fracture mechanics * Path-independent integral Subject RIV: JL - Materials Fatigue, Friction Mechanics Impact factor: 1.262, year: 2014

  17. Nuclear reaction models - source term estimation for safety design in accelerators

    International Nuclear Information System (INIS)

    Nandy, Maitreyee

    2013-01-01

    Accelerator driven subcritical system (ADSS) employs proton induced spallation reaction at a few GeV. Safety design of these systems involves source term estimation in two steps - multiple fragmentation of the target and n+γ emission through a fast process followed by statistical decay of the primary fragments. The prompt radiation field is estimated in the framework of quantum molecular dynamics (QMD) theory, intra-nuclear cascade or Monte Carlo calculations. A few nuclear reaction model codes used for this purpose are QMD, JQMD, Bertini, INCL4, PHITS, followed by statistical decay codes like ABLA, GEM, GEMINI, etc. In the case of electron accelerators photons and photoneutrons dominate the prompt radiation field. High energy photon yield through Bremsstrahlung is estimated in the framework of Born approximation while photoneutron production is calculated using giant dipole resonance and quasi-deuteron formation cross section. In this talk hybrid and exciton PEQ models and QMD formalism will be discussed briefly

  18. Use of WIMS-E lattice code for prediction of the transuranic source term for spent fuel dose estimation

    International Nuclear Information System (INIS)

    Schwinkendorf, K.N.

    1996-01-01

    A recent source term analysis has shown a discrepancy between ORIGEN2 transuranic isotopic production estimates and those produced with the WIMS-E lattice physics code. Excellent agreement between relevant experimental measurements and WIMS-E was shown, thus exposing an error in the cross section library used by ORIGEN2

  19. Kinetic parameters for source driven systems

    International Nuclear Information System (INIS)

    Dulla, S.; Ravetto, P.; Carta, M.; D'Angelo, A.

    2006-01-01

    The definition of the characteristic kinetic parameters of a subcritical source-driven system constitutes an interesting problem in reactor physics with important consequences for practical applications. Consistent and physically meaningful values of the parameters allow to obtain accurate results from kinetic simulation tools and to correctly interpret kinetic experiments. For subcritical systems a preliminary problem arises for the adoption of a suitable weighting function to be used in the projection procedure to derive a point model. The present work illustrates a consistent factorization-projection procedure which leads to the definition of the kinetic parameters in a straightforward manner. The reactivity term is introduced coherently with the generalized perturbation theory applied to the source multiplication factor ks, which is thus given a physical role in the kinetic model. The effective prompt lifetime is introduced on the assumption that a neutron generation can be initiated by both the fission process and the source emission. Results are presented for simplified configurations to fully comprehend the physical features and for a more complicated highly decoupled system treated in transport theory. (authors)

  20. Long-term monitoring on environmental disasters using multi-source remote sensing technique

    Science.gov (United States)

    Kuo, Y. C.; Chen, C. F.

    2017-12-01

    Environmental disasters are extreme events within the earth's system that cause deaths and injuries to humans, as well as causing damages and losses of valuable assets, such as buildings, communication systems, farmlands, forest and etc. In disaster management, a large amount of multi-temporal spatial data is required. Multi-source remote sensing data with different spatial, spectral and temporal resolutions is widely applied on environmental disaster monitoring. With multi-source and multi-temporal high resolution images, we conduct rapid, systematic and seriate observations regarding to economic damages and environmental disasters on earth. It is based on three monitoring platforms: remote sensing, UAS (Unmanned Aircraft Systems) and ground investigation. The advantages of using UAS technology include great mobility and availability in real-time rapid and more flexible weather conditions. The system can produce long-term spatial distribution information from environmental disasters, obtaining high-resolution remote sensing data and field verification data in key monitoring areas. It also supports the prevention and control on ocean pollutions, illegally disposed wastes and pine pests in different scales. Meanwhile, digital photogrammetry can be applied on the camera inside and outside the position parameters to produce Digital Surface Model (DSM) data. The latest terrain environment information is simulated by using DSM data, and can be used as references in disaster recovery in the future.

  1. Residential Mobility and Lung Cancer Risk: Data-Driven Exploration Using Internet Sources

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Hong-Jun [ORNL; Tourassi, Georgia [ORNL; Xu, Songhua [New Jersey Insitute of Technology

    2015-01-01

    Frequent relocation has been linked to health decline, particularly with respect to emotional and psychological wellbeing. In this paper we investigate whether there is an association between frequent relocation and lung cancer risk. For the initial investigation we leverage two online data sources to collect cancer and control subjects using web crawling and tailored text mining. The two data sources share different strengths and weaknesses in terms of the amount of detail, population representation, and sample size. One data source includes online obituaries. The second data source includes augmented LinkedIn profiles. For each data source, the subjects spatiotemporal history is reconstructed from the available information provided in the obituaries and from the education and work experience provided in the LinkedIn profiles. The study shows that lung cancer subjects have higher mobility frequency than the control group. This trend is consistent for both data sources.

  2. Surgeon General's Family Health History Initiative

    Science.gov (United States)

    ... Source Code The Surgeon General's Family Health History Initiative To help focus attention on the importance of ... health campaign, called the Surgeon General's Family History Initiative, to encourage all American families to learn more ...

  3. Source-term development for a contaminant plume for use by multimedia risk assessment models

    International Nuclear Information System (INIS)

    Whelan, Gene; McDonald, John P.; Taira, Randal Y.; Gnanapragasam, Emmanuel K.; Yu, Charley; Lew, Christine S.; Mills, William B.

    1999-01-01

    Multimedia modelers from the U.S. Environmental Protection Agency (EPA) and the U.S. Department of Energy (DOE) are collaborating to conduct a comprehensive and quantitative benchmarking analysis of four intermedia models: DOE's Multimedia Environmental Pollutant Assessment System (MEPAS), EPA's MMSOILS, EPA's PRESTO, and DOE's RESidual RADioactivity (RESRAD). These models represent typical analytically, semi-analytically, and empirically based tools that are utilized in human risk and endangerment assessments for use at installations containing radioactive and/or hazardous contaminants. Although the benchmarking exercise traditionally emphasizes the application and comparison of these models, the establishment of a Conceptual Site Model (CSM) should be viewed with equal importance. This paper reviews an approach for developing a CSM of an existing, real-world, Sr-90 plume at DOE's Hanford installation in Richland, Washington, for use in a multimedia-based benchmarking exercise bet ween MEPAS, MMSOILS, PRESTO, and RESRAD. In an unconventional move for analytically based modeling, the benchmarking exercise will begin with the plume as the source of contamination. The source and release mechanism are developed and described within the context of performing a preliminary risk assessment utilizing these analytical models. By beginning with the plume as the source term, this paper reviews a typical process and procedure an analyst would follow in developing a CSM for use in a preliminary assessment using this class of analytical tool

  4. Reducing plant radiation fields by source term reduction - tracking cobalt and antimony to their sources at Gentilly-2

    International Nuclear Information System (INIS)

    Gauthier, P.; Guzonas, D.A.

    2006-01-01

    Gentilly-2 NGS is experiencing high radiation fields in the fuelling machine vaults. These high fields make maintenance outages more expensive and their management more complicated. As part of the station refurbishment project, a task group was created to identify the cause of the high fields and make recommendations to prevent their reoccurrence in the second (post-refurbishment) operating cycle. To identify the root cause of the problem, the task group decided to analyse the primary heat transport system (PHTS), the fuel handling system and their inter-relation. Gentilly-2 has had to manage a unique (to CANDU) problem arising from antimony released from the main heat transport pump seals. Antimony deposits on in-core surfaces, becomes activated, and subsequently can be released, especially under oxidizing coolant conditions. It then becomes incorporated into the magnetite deposits on PHTS piping, including the steam generators and inlet feeders. Gentilly-2 has focused a great deal of effort on managing antimony over the last 15 years. As a result of these initiatives, radioantimony fields have been quite effectively managed since 1997, resulting in a decrease in their relative contribution to the total fields. The decrease in radioantimony fields highlighted the significant contribution of 60 Co cobalt activity; the high levels of both radioantimony and 60 Co differentiate Gentilly-2 from other CANDU 6 plants. Two types of 59 Co sources are present in the CANDU PHTS. High surface area materials such as steam generator tubes and feeder pipes contain trace concentrations of 59 Co as an impurity, which can be released by corrosion. Low surface area materials such as Stellites contain high concentrations of 59 Co that can be released as either corrosion or wear products. After assessing potential cobalt sources, the task group concluded that PHTS materials were not likely the origin of the high 60 Co fields. The major PHTS components identified as cobalt sources have

  5. Activities and sources of income after a period of long-term sick leave - a population-based prospective cohort study

    Directory of Open Access Journals (Sweden)

    Wikman Anders

    2012-09-01

    Full Text Available Abstract Background There is limited knowledge about what happens to people after long-term sick leave. The aim of this report was to conduct a prospective study of individuals who were on prolonged sick leave during a particular year, considering their activities and sources of income during subsequent years. To enable comparison of different time periods, we used three cohorts of individuals with different starting years. Methods Using data from national registers, three separate cohorts were constructed that included all people living in Sweden who were 20-64 years of age (>5 million in the years 1995, 2000 and 2005, respectively. The individual members of the cohorts were classified into the following groups based on their main source of income and activity in 1995-2008: on long-term sick leave, employed, old-age pensioner, long-term unemployed, disability pensioner, on parental leave, social assistance recipient, student allowance recipient, deceased, or emigrated. Results Most individuals on long-term (> 6 months sick leave in 1995 were not employed 13 years later. Only 11% of the women and 13% of the men were primarily in employment after 13 years. Instead, a wide range of alternatives existed, for example, many had been granted disability pension, and about 10% of the women and 17% of the men had died during the follow-up period. A larger proportion of those with long-term sick leave were back in employment when 2005 was the starting year for the follow-up. Conclusions The low future employment rates for people on long-term sick leave may seem surprising. There are several possible explanations for the finding: The disorders these people may have, might have entailed longstanding difficulties on the labor market. Besides, long-term absence from work, no matter what its causes were, might have worsen the chances of further employment. The economic cycles may also have been of importance. The improving labor market during later years seems

  6. Activities and sources of income after a period of long-term sick leave--a population-based prospective cohort study.

    Science.gov (United States)

    Wikman, Anders; Wiberg, Michael; Marklund, Staffan; Alexanderson, Kristina

    2012-09-06

    There is limited knowledge about what happens to people after long-term sick leave. The aim of this report was to conduct a prospective study of individuals who were on prolonged sick leave during a particular year, considering their activities and sources of income during subsequent years. To enable comparison of different time periods, we used three cohorts of individuals with different starting years. Using data from national registers, three separate cohorts were constructed that included all people living in Sweden who were 20-64 years of age (>5 million) in the years 1995, 2000 and 2005, respectively. The individual members of the cohorts were classified into the following groups based on their main source of income and activity in 1995-2008: on long-term sick leave, employed, old-age pensioner, long-term unemployed, disability pensioner, on parental leave, social assistance recipient, student allowance recipient, deceased, or emigrated. Most individuals on long-term (> 6 months) sick leave in 1995 were not employed 13 years later. Only 11% of the women and 13% of the men were primarily in employment after 13 years. Instead, a wide range of alternatives existed, for example, many had been granted disability pension, and about 10% of the women and 17% of the men had died during the follow-up period. A larger proportion of those with long-term sick leave were back in employment when 2005 was the starting year for the follow-up. The low future employment rates for people on long-term sick leave may seem surprising. There are several possible explanations for the finding: The disorders these people may have, might have entailed longstanding difficulties on the labor market. Besides, long-term absence from work, no matter what its causes were, might have worsen the chances of further employment. The economic cycles may also have been of importance. The improving labor market during later years seems to have improved the chances for employment among those earlier

  7. A modification of the Regional Nutrient Management model (ReNuMa) to identify long-term changes in riverine nitrogen sources

    Science.gov (United States)

    Hu, Minpeng; Liu, Yanmei; Wang, Jiahui; Dahlgren, Randy A.; Chen, Dingjiang

    2018-06-01

    Source apportionment is critical for guiding development of efficient watershed nitrogen (N) pollution control measures. The ReNuMa (Regional Nutrient Management) model, a semi-empirical, semi-process-oriented model with modest data requirements, has been widely used for riverine N source apportionment. However, the ReNuMa model contains limitations for addressing long-term N dynamics by ignoring temporal changes in atmospheric N deposition rates and N-leaching lag effects. This work modified the ReNuMa model by revising the source code to allow yearly changes in atmospheric N deposition and incorporation of N-leaching lag effects into N transport processes. The appropriate N-leaching lag time was determined from cross-correlation analysis between annual watershed individual N source inputs and riverine N export. Accuracy of the modified ReNuMa model was demonstrated through analysis of a 31-year water quality record (1980-2010) from the Yongan watershed in eastern China. The revisions considerably improved the accuracy (Nash-Sutcliff coefficient increased by ∼0.2) of the modified ReNuMa model for predicting riverine N loads. The modified model explicitly identified annual and seasonal changes in contributions of various N sources (i.e., point vs. nonpoint source, surface runoff vs. groundwater) to riverine N loads as well as the fate of watershed anthropogenic N inputs. Model results were consistent with previously modeled or observed lag time length as well as changes in riverine chloride and nitrate concentrations during the low-flow regime and available N levels in agricultural soils of this watershed. The modified ReNuMa model is applicable for addressing long-term changes in riverine N sources, providing decision-makers with critical information for guiding watershed N pollution control strategies.

  8. The alternative means process for the Port Hope Area Initiative

    International Nuclear Information System (INIS)

    O'Neill, J.E.; Campbell, D.; Rossi, R.

    2006-01-01

    In March of 2001, the Government of Canada, the Town of Port Hope, Hope Township and the Municipality of Clarington agreed to the cleanup and long-term management of historic, low-level radioactive waste materials in these communities. The agreement identified conceptual designs for long-term management facilities for the wastes. Two environmental assessments (EAs) of the proposed long-term management facilities have been initiated as part of the Port Hope Area Initiative (PHAI); namely the Port Hope Long-Term Low-Level Radioactive Waste Management Project and the Port Granby Long-Term Low-Level Radioactive Waste Management Project. A requirement set out in the Scope for the EAs is the consideration of technically and economically feasible Alternative Means of carrying out the PHAI projects. Alternative Means are the various ways that the projects could be implemented, such as alternative technologies, sites, transportation routes, etc. Early in the overall EA processes the Low-Level Radioactive Waste Management Office (LLRWMO), which is responsible for undertaking the EAs, recognized that it was facing a significant challenge; namely, the successful completion of a clear, technically sound and defendable Alternative Means analysis, including consultation with and acceptance by the community. This would be a fundamental requirement for the success of the PHAI EAs. A further challenge was to develop consistent assessment methodologies for the Port Hope and Port Granby projects, which were both initiated under the PHAI at the same time. Although similar in many respects, the two projects have major differences. For example, the Port Hope Project, with more sources of contamination within a built- up urban area is more complex and has a broader range of potential solutions to be considered than the rural Port Granby Project. This paper describes how the LLRWMO met that challenge, developed and implemented a successful Alternative Means process and presents the

  9. Conditioning of disused sealed sources in countries without disposal facility: Short term gain - long term pain

    International Nuclear Information System (INIS)

    Benitez-Navarro, J.C.; Salgado-Mojena, M.

    2002-01-01

    Owing to the considerable development in managing disused sealed radioactive sources (DSRS), the limited availability of disposal practices for them, and the new recommendations for the use of borehole disposal concept, it was felt that a paper reviewing the existing recommendations could be a starting point of discussion on the retrievability of the sources. Even when no international consensus exists as to an acceptable solution for the challenge of disposal of disused sealed sources, the 'Best Available Technology' for managing most of them, recommended for developing countries, included the cementation of the sources. The waste packages prepared in such a way do not allow any flexibility to accommodate possible future disposal requirements. Therefore, the 'Wait and See' approach could be also recommended for managing not only the sources with long-live radionuclides and high activity, but probably for all kind of existing disused sealed sources. The general aim of the current paper is to identify and review the current recommendations for managing disused sealed sources and to meditate on the most convenient management schemes for disused sealed radioactive sources in Member States without disposal capacities (Latin America, Africa). The risk that cemented DSRS could be incompatible with future disposal requirements was taken into account. (author)

  10. Financing Preference Behaviour for Private Finance Initiative (PFI Projects

    Directory of Open Access Journals (Sweden)

    Yati Md Lasa

    2016-01-01

    Full Text Available Project Financing Initiative (PFI projects require the private sector to invest an enormous amount of capital for the development of public projects. The private sector has to seek cost-effective financing sources for their survival in the long-term concession. Conventional financing uses widely; however, Islamic financing promises better financing through profit and loss sharing. This paper reviews financing preferences for PFI projects and the factors influencing the choice of funding. The results show that religious perspective, quality of services, financing facilities and reputation are the factors that are expected will influence the financing preference behaviour, either Islamic or conventional finance.

  11. Techniques for long term conditioning and storage of radium sources

    International Nuclear Information System (INIS)

    Dogaru, Gheorghe; Dragolici, Felicia; Nicu, Mihaela

    2008-01-01

    The Horia Hulubei National Institute of Research and Development for Physics and Nuclear Engineering developed its own technology for conditioning the radium spent sealed radioactive sources. The laboratory dedicated to radiological characterization, identification of radium sources as well as the encapsulation of spent sealed radioactive sources was equipped with a local ventilation system, welding devices, tightness test devices as well as radiometric portable devices. Two types of capsules have been designed for conditioning of radium spent sealed radioactive sources. For these kinds of capsules different types of storage packaging were developed. Data on the radium inventory will be presented in the paper. The paper contains the description of the process of conditioning of spent sealed radioactive sources as well as the description of the capsules and packaging. The paper describes the equipment used for the conditioning of the radium spent sealed sources. (authors)

  12. Global Methane Initiative

    Science.gov (United States)

    The Global Methane Initiative promotes cost-effective, near-term methane recovery through partnerships between developed and developing countries, with participation from the private sector, development banks, and nongovernmental organizations.

  13. 10 years and 20,000 sources: the offsite source recovery project

    Energy Technology Data Exchange (ETDEWEB)

    Whitworth, Julia R [Los Alamos National Laboratory; Abeyta, Cristy L [Los Alamos National Laboratory; Pearson, Michael W [Los Alamos National Laboratory

    2009-01-01

    The Global Threat Reduction Initiative's (GTRI) Offsite Source Recovery Project (OSRP) has been recovering excess and unwanted sealed sources for ten years. In January 2009, GTRI announced that the project had recovered 20,000 sealed radioactive sources. This project grew out of early efforts at Los Alamos National Laboratory (LANL) to recover and disposition excess Plutonium-239 (Pu-239) sealed sources that were distributed in the 1960s and 1970s under the Atoms for Peace Program. Sealed source recovery was initially considered a waste management activity, as evidenced by its initial organization under the Department of Energy's (DOE's) Environmental Management (EM) program. After the terrorist attacks of 2001, however, the interagency community began to recognize the threat posed by excess and unwanted radiological material, particularly those that could not be disposed at the end of their useful life. After being transferred to the National Nuclear Security Administration (NNSA) to be part of GTRI, OSRP's mission was expanded to include not only material that would be classified as Greater-than-Class-C (GTCC) when it became waste, but also any other materials that might be a 'national security consideration.' This paper discusses OSRP's history, recovery operations, expansion to accept high-activity beta-gamma-emitting sealed sources and devices and foreign-possessed sources, and more recent efforts such as cooperative projects with the Council on Radiation Control Program Directors (CRCPD) and involvement in GTRI's Search and Secure project. Current challenges and future work will also be discussed.

  14. Fluid model of the sheath in front of a floating electrode immersed in a magnetized plasma with oblique magnetic field: Some comments on ion source terms and ion temperature effects

    International Nuclear Information System (INIS)

    Gyergyek, T.; Kovačič, J.

    2015-01-01

    A one-dimensional fluid model of the magnetized plasma-wall transition region in front of a floating electrode immersed in a magnetized plasma with oblique magnetic field is presented. The Boltzmann relation is assumed for the electrons, while the positive ions obey the ion continuity and momentum exchange equation. The ions are assumed to be isothermal. By comparison with a two-fluid model, it is shown that assuming the Boltzmann relation for the electrons implies that there is no creation or annihilation of the electrons. Consequently, there should not be any creation and annihilation of the positive ions either. The models that assume the Boltzmann relation for the electrons and a non-zero ion source term at the same time are therefore inconsistent, but such models have nevertheless been used extensively by many authors. So, in this work, an extensive comparison of the results obtained using the zero source term on one hand and three different non-zero source terms on the other hand is made. Four different ion source terms are considered in total: the zero source term and three different non-zero ion source terms. When the zero source term is used, the model becomes very sensitive to the boundary conditions, and in some cases, the solutions exhibit large amplitude oscillations. If any of the three non-zero ion source terms is used, those problems are eliminated, but also the consistency of the model is broken. The model equations are solved numerically in the entire magnetized plasma-wall transition region. For zero ion temperature, the model can be solved even if a very small ion velocity is selected as a boundary condition. For finite ion temperature, the system of equations becomes stiff, unless the ion velocity at the boundary is increased slightly above the ion thermal velocity. A simple method how to find a solution with a very small ion velocity at the boundary also for finite ion temperature in the entire magnetized plasma-wall transition region is

  15. Reducing the global threat of radiological terrorism in Central Asia and Caucus regions. The global threat reduction initiative approach to radioactive source security

    International Nuclear Information System (INIS)

    Smith, E.

    2010-01-01

    The security of radioactive sources is of worldwide concern, due to their wide use in civilian commerce and the potentially devastating effects of their misuse. In cooperation with host countries and international partners, the Global Threat Reduction Initiative has utilized a proven process for providing technical and financial assistance to protect radioactive sources in diverse uses and unique circumstances at hundreds of sites worldwide. The mission of the Department of Energy, National Nuclear Security Administration's program includes reducing the risk posed by vulnerable radiological materials that could be used in a Radioactive Dispersal Device). The program's objectives are to identify, consolidate, secure, and/or dispose of high-activity radiological materials to prevent their theft and malicious use. The Global Threat Reduction Initiative Program's scope is global, with projects in over 100 countries at more than 755 radiological sites, including industrial, medical and commercial facilities. In addition to working bilaterally, the Program works closely with the International Atomic Energy Agency (IAEA) and other partner countries. (author)

  16. Development of a MELCOR self-initialization algorithm for boiling water reactors

    International Nuclear Information System (INIS)

    Chien, C.S.; Wang, S.J.; Cheng, S.K.

    1996-01-01

    The MELCOR code, developed by Sandia National Laboratories, is suitable for calculating source terms and simulating severe accident phenomena of nuclear power plants. Prior to simulating a severe accident transient with MELCOR, the initial steady-state conditions must be generated in advance. The current MELCOR users' manuals do not provide a self-initialization procedure; this is the reason users have to adjust the initial conditions by themselves through a trial-and-error approach. A MELCOR self-initialization algorithm for boiling water reactor plants has been developed, which eliminates the tedious trial-and-error procedures and improves the simulation accuracy. This algorithm adjusts the important plant variable such as the dome pressure, downcomer level, and core flow rate to the desired conditions automatically. It is implemented through input with control functions provided in MELCOR. The reactor power and feedwater temperature are fed as input data. The initialization work of full-power conditions of the Kuosheng nuclear power station is cited as an example. These initial conditions are generated successfully with the developed algorithm. The generated initial conditions can be stored in a restart file and used for transient analysis. The methodology in this study improves the accuracy and consistency of transient calculations. Meanwhile, the algorithm provides all MELCOR users an easy and correct method for establishing the initial conditions

  17. Source term estimation for small sized HTRs: status and further needs - a german approach

    International Nuclear Information System (INIS)

    Moormann, R.; Schenk, W.; Verfondern, K.

    2000-01-01

    The main results of German studies on source term estimation for small pebble-bed HTRs with their strict safety demands are outlined. Core heat-up events are no longer dominant for modern high quality fuel, but fission product transport during water ingress accidents (steam cycle plants) and depressurization is relevant, mainly due to remobilization of fission products which were plated-out in the course of normal operation or became dust borne. An important lack of knowledge was identified as concerns data on plate-out under normal operation, as well as on the behaviour of dust borne activity as a whole. Improved knowledge in this field is also important for maintenance/repair and design/shielding. For core heat-up events the influence of burn-up on temperature induced fission product release has to be measured for future high burn-up fuel. Also, transport mechanisms out of the He circuit into the environment require further examination. For water/steam ingress events mobilization of plated-out fission products by steam or water has to be considered in detail, along with steam interaction with kernels of particles with defective coatings. For source terms of depressurization, a more detailed knowledge of the flow pattern and shear forces on the various surfaces is necessary. In order to improve the knowledge on plate-out and dust in normal operation and to generate specimens for experimental remobilization studies, planning/design of plate-out/dust examination facilities which could be added to the next generation of HTRs (HTR10,HTTR) is proposed. For severe air ingress and reactivity accidents, behaviour of future advanced fuel elements has to be experimentally tested. (authors)

  18. An artificial neural network approach to reconstruct the source term of a nuclear accident

    International Nuclear Information System (INIS)

    Giles, J.; Palma, C. R.; Weller, P.

    1997-01-01

    This work makes use of one of the main features of artificial neural networks, which is their ability to 'learn' from sets of known input and output data. Indeed, a trained artificial neural network can be used to make predictions on the input data when the output is known, and this feedback process enables one to reconstruct the source term from field observations. With this aim, an artificial neural networks has been trained, using the projections of a segmented plume atmospheric dispersion model at fixed points, simulating a set of gamma detectors located outside the perimeter of a nuclear facility. The resulting set of artificial neural networks was used to determine the release fraction and rate for each of the noble gases, iodines and particulate fission products that could originate from a nuclear accident. Model projections were made using a large data set consisting of effective release height, release fraction of noble gases, iodines and particulate fission products, atmospheric stability, wind speed and wind direction. The model computed nuclide-specific gamma dose rates. The locations of the detectors were chosen taking into account both building shine and wake effects, and varied in distance between 800 and 1200 m from the reactor.The inputs to the artificial neural networks consisted of the measurements from the detector array, atmospheric stability, wind speed and wind direction; the outputs comprised a set of release fractions and heights. Once trained, the artificial neural networks was used to reconstruct the source term from the detector responses for data sets not used in training. The preliminary results are encouraging and show that the noble gases and particulate fission product release fractions are well determined

  19. Initial testing of a Compact Crystal Positioning System for the TOPAZ Single-Crystal Diffractometer at the Spallation Neutron Source

    International Nuclear Information System (INIS)

    Frost, Matthew J.; Austin, Michael D.; Viola, Robert; Thomison, Jack; Carmen, Peter; Hoffmann, Christina; Miller, Echo M.; Mosier, Lisa B.; Overbay, Mark A.

    2009-01-01

    A precise, versatile, and automated method of orienting a sub-millimeter crystal in a focused neutron beam is required for e cient operation of the TOPAZ Single Crystal Di ractometer at the Spallation Neutron Source at Oak Ridge National Laboratory. To ful ll this need, a Compact Crystal Positioning System (CCPS) has been developed in collaboration with Square One Systems Design in Jackson, Wyoming. The system incorporates a tripod design with six vacuum-compatible piezoelectric linear motors capable of < 1 m resolution. National Instruments LabVIEW provides a means of system automation while at the same time accommodating the modular nature of the SNS sample environment control software for straightforward system integration. Initial results in a cryogenic test environment will be presented, as well as results from ambient tests performed at the Advanced Photon Source at Argonne National Laboratory.

  20. The initial phase of sudden releases of superheated liquid

    International Nuclear Information System (INIS)

    Schmidli, J.; Yadigaroglu, G.

    1994-01-01

    Series of experiments were conducted with refrigerants-114, -12, propane and butane to investigate the initial phase of sudden releases of superheated liquids due to the catastrophic failure of the vessel containing them. The experiments were initiated by shattering spherical flasks of 100 to 2000 ml containing the liquefied, pressurized gases. The variable parameters were the initial superheat, the filling level, the height of the flask above ground, and the relative humidity of the surrounding air. It was found that the initial flashing process is not determined by homogeneous nucleation, but rather by surface instabilities which lead to an evaporation wave traveling from the initial surface towards the center of the released mass. Cloud shape and expansion velocity could be determined from high speed recordings covering the initial stage of the release during which gravity has no influence. When the internal energy was sufficient, it was observed that the expanding droplet/vapor cloud initially propagated spherically with a constant expansion velocity, until Rayleigh-Taylor type instabilities appeared at its surface. Information about the pool which can be formed on the ground, the pressure decay within the flask, the droplet size, and the cloud temperature was collected. The experimental findings for the expansion velocity, as well as for the pool fraction, were the base for a nondimensional analysis leading to correlations which describe the initial phase of such releases and can be used to define the ''source term'' for turbulent dispersion models. (author) 5 figs., 1 tab., 15 refs

  1. Prospects of renewable energy sources in India: Prioritization of alternative sources in terms of Energy Index

    International Nuclear Information System (INIS)

    Jha, Shibani K.; Puppala, Harish

    2017-01-01

    The growing energy demand in progressing civilization governs the exploitation of various renewable sources over the conventional sources. Wind, Solar, Hydro, Biomass, and waste & Bagasse are the various available renewable sources in India. A reliable nonconventional geothermal source is also available in India but it is restricted to direct heat applications. This study archives the status of renewable alternatives in India. The techno economic factors and environmental aspects associated with each of these alternatives are discussed. This study focusses on prioritizing the renewable sources based on a parameter introduced as Energy Index. This index is evaluated using cumulative scores obtained for each of the alternatives. The cumulative score is obtained by evaluating each alternative over a range of eleven environmental and techno economic criteria following Fuzzy Analytical Hierarchy Process. The eleven criteria's considered in the study are Carbon dioxide emissions (CO 2 ), Sulphur dioxide emissions (SO 2 ), Nitrogen oxide emissions (NO x ), Land requirement, Current energy cost, Potential future energy cost, Turnkey investment, Capacity factor, Energy efficiency, Design period and Water consumption. It is concluded from the study that the geothermal source is the most preferable alternative with highest Energy Index. Hydro, Wind, Biomass and Solar sources are subsequently preferred alternatives. - Highlights: • FAH process is used to obtain cumulative score for each renewable alternative. • Cumulative score is normalized by highest score of ideal source. • Energy Index shows how best a renewable alternative is. • Priority order is obtained for alternatives based on Energy Index. • Geothermal is most preferable source followed by Hydro, Wind, Biomass and Solar.

  2. Evaluation of long-term community recovery from Hurricane Andrew: sources of assistance received by population sub-groups.

    Science.gov (United States)

    McDonnell, S; Troiano, R P; Barker, N; Noji, E; Hlady, W G; Hopkins, R

    1995-12-01

    Two three-stage cluster surveys were conducted in South Dade County, Florida, 14 months apart, to assess recovery following Hurricane Andrew. Response rates were 75 per cent and 84 per cent. Sources of assistance used in recovery from Hurricane Andrew differed according to race, per capita income, ethnicity, and education. Reports of improved living situation post-hurricane were not associated with receiving relief assistance, but reports of a worse situation were associated with loss of income, being exploited, or job loss. The number of households reporting problems with crime and community violence doubled between the two surveys. Disaster relief efforts had less impact on subjective long-term recovery than did job or income loss or housing repair difficulties. Existing sources of assistance were used more often than specific post-hurricane relief resources. The demographic make-up of a community may determine which are the most effective means to inform them after a disaster and what sources of assistance may be useful.

  3. A source term estimation method for a nuclear accident using atmospheric dispersion models

    DEFF Research Database (Denmark)

    Kim, Minsik; Ohba, Ryohji; Oura, Masamichi

    2015-01-01

    The objective of this study is to develop an operational source term estimation (STE) method applicable for a nuclear accident like the incident that occurred at the Fukushima Dai-ichi nuclear power station in 2011. The new STE method presented here is based on data from atmospheric dispersion...... models and short-range observational data around the nuclear power plants.The accuracy of this method is validated with data from a wind tunnel study that involved a tracer gas release from a scaled model experiment at Tokai Daini nuclear power station in Japan. We then use the methodology developed...... and validated through the effort described in this manuscript to estimate the release rate of radioactive material from the Fukushima Dai-ichi nuclear power station....

  4. Synchrotron light sources in developing countries

    Science.gov (United States)

    Mtingwa, Sekazi K.; Winick, Herman

    2018-03-01

    We discuss the role that synchrotron light sources, such as SESAME, could play in improving the socioeconomic conditions in developing countries. After providing a brief description of a synchrotron light source, we discuss the important role that they played in the development of several economically emerging countries. Then we describe the state of synchrotron science in South Africa and that country’s leadership role in founding the African Light Source initiative. Next, we highlight a new initiative called Lightsources for Africa, the Americas & Middle East Project, which is a global initiative led by the International Union of Pure and Applied Physics and the International Union of Crystallography, with initial funding provided by the International Council for Science. Finally, we comment on a new technology called the multibend achromat that has launched a new paradigm for the design of synchrotron light sources that should be attractive for construction in developing countries.

  5. ISS Ambient Air Quality: Updated Inventory of Known Aerosol Sources

    Science.gov (United States)

    Meyer, Marit

    2014-01-01

    Spacecraft cabin air quality is of fundamental importance to crew health, with concerns encompassing both gaseous contaminants and particulate matter. Little opportunity exists for direct measurement of aerosol concentrations on the International Space Station (ISS), however, an aerosol source model was developed for the purpose of filtration and ventilation systems design. This model has successfully been applied, however, since the initial effort, an increase in the number of crewmembers from 3 to 6 and new processes on board the ISS necessitate an updated aerosol inventory to accurately reflect the current ambient aerosol conditions. Results from recent analyses of dust samples from ISS, combined with a literature review provide new predicted aerosol emission rates in terms of size-segregated mass and number concentration. Some new aerosol sources have been considered and added to the existing array of materials. The goal of this work is to provide updated filtration model inputs which can verify that the current ISS filtration system is adequate and filter lifetime targets are met. This inventory of aerosol sources is applicable to other spacecraft, and becomes more important as NASA considers future long term exploration missions, which will preclude the opportunity for resupply of filtration products.

  6. Independent assessment of MELCOR as a severe accident thermal-hydraulic/source term analysis tool

    International Nuclear Information System (INIS)

    Madni, I.K.; Eltawila, F.

    1994-01-01

    MELCOR is a fully integrated computer code that models all phases of the progression of severe accidents in light water reactor nuclear power plants, and is being developed for the US Nuclear Regulatory Commission (NRC) by Sandia National Laboratories (SNL). Brookhaven National Laboratory (BNL) has a program with the NRC called ''MELCOR Verification, Benchmarking, and Applications,'' whose aim is to provide independent assessment of MELCOR as a severe accident thermal-hydraulic/source term analysis tool. The scope of this program is to perform quality control verification on all released versions of MELCOR, to benchmark MELCOR against more mechanistic codes and experimental data from severe fuel damage tests, and to evaluate the ability of MELCOR to simulate long-term severe accident transients in commercial LWRs, by applying the code to model both BWRs and PWRs. Under this program, BNL provided input to the NRC-sponsored MELCOR Peer Review, and is currently contributing to the MELCOR Cooperative Assessment Program (MCAP). This paper presents a summary of MELCOR assessment efforts at BNL and their contribution to NRC goals with respect to MELCOR

  7. Urban stormwater source control policies: why and how?

    Directory of Open Access Journals (Sweden)

    G. Petrucci

    2014-09-01

    Full Text Available Stormwater source control is becoming a common strategy for urban stormwater management in many countries. It relies on regulations or other policy instruments compelling or inciting implementation, for each new urban development, of small-scale facilities to locally store and manage stormwater. Local authorities that pioneered source control since the 1980s have already observed that small-scale facilities systematically implemented over a catchment are able to influence its hydrological behaviour. This capability is the main strength of source control, as it allows compensation for the negative effects of urbanization. Yet, it also represents its main risk: if initial decision-making is not sufficiently accurate, source control can produce long-term negative effects. Because of its current spreading, source control will acquire an increasing role as a driver of hydrological changes in urban catchments, and the directions of these changes depend on current policy-making practices. This paper presents an analysis and a critical discussion of the main objectives that policy-makers attribute to stormwater source control. The investigation is based on a sample of French case studies, completed by a literature review for international comparison. It identifies four main objectives, some typical of urban stormwater management and some more innovative: flood reduction, receiving waters protection, sustainable development, costs reduction. The discussion focuses on how current policy-making practices are able to translate these objectives in concrete policy instruments, and on which knowledge and tools could improve this process. It is shown that for some objectives, basic knowledge is available, but the creation of policy instruments which are effective at the catchment scale and adapted to local conditions is still problematic. For other objectives, substantial lacks of knowledge exist, casting doubts on long-term effectiveness of current policy

  8. Toward a comprehensive long term nicotine policy.

    Science.gov (United States)

    Gray, N; Henningfield, J E; Benowitz, N L; Connolly, G N; Dresler, C; Fagerstrom, K; Jarvis, M J; Boyle, P

    2005-06-01

    Global tobacco deaths are high and rising. Tobacco use is primarily driven by nicotine addiction. Overall tobacco control policy is relatively well agreed upon but a long term nicotine policy has been less well considered and requires further debate. Reaching consensus is important because a nicotine policy is integral to the target of reducing tobacco caused disease, and the contentious issues need to be resolved before the necessary political changes can be sought. A long term and comprehensive nicotine policy is proposed here. It envisages both reducing the attractiveness and addictiveness of existing tobacco based nicotine delivery systems as well as providing alternative sources of acceptable clean nicotine as competition for tobacco. Clean nicotine is defined as nicotine free enough of tobacco toxicants to pass regulatory approval. A three phase policy is proposed. The initial phase requires regulatory capture of cigarette and smoke constituents liberalising the market for clean nicotine; regulating all nicotine sources from the same agency; and research into nicotine absorption and the role of tobacco additives in this process. The second phase anticipates clean nicotine overtaking tobacco as the primary source of the drug (facilitated by use of regulatory and taxation measures); simplification of tobacco products by limitation of additives which make tobacco attractive and easier to smoke (but tobacco would still be able to provide a satisfying dose of nicotine). The third phase includes a progressive reduction in the nicotine content of cigarettes, with clean nicotine freely available to take the place of tobacco as society's main nicotine source.

  9. The uranium industry: long-term planning for short-term competition

    International Nuclear Information System (INIS)

    Vottero, X.; Georges Capus, G.

    2001-01-01

    Long term planning for short term competition Today, uranium producers face new challenges in terms of both production (new regulatory, environmental and social constraints) and market conditions (new sources of uranium supply, very low prices and tough competition). In such a context, long-term planning is not just a prerequisite to survive in the nuclear fuel cycle industry. In fact, it also contributes to sustaining nuclear electricity generation facing fierce competition from other energy sources in increasingly deregulated markets. Firstly, the risk of investing in new mining projects in western countries is growing because, on the one hand, of very erratic market conditions and, on the other hand, of increasingly lengthy, complex and unpredictable regulatory conditions. Secondly, the supply of other sources of uranium (uranium derived from nuclear weapons, uranium produced in CIS countries, ...) involve other risks, mainly related to politics and commercial restrictions. Consequently, competitive uranium supply requires not only technical competence but also financial strength and good marketing capabilities in order to anticipate long-term market trends, in terms of both demand and supply. It also requires taking into account new parameters such as politics, environment, regulations, etc. Today, a supplier dedicated to the sustainable production of nuclear electricity must manage a broad range of long-term risks inherent to the procurement of uranium. Taking into account all these parameters in a context of short-term, fast-changing market is a great challenge for the future generation. World Uranium Civilian Supply and Demand. (authors)

  10. Association Between Facility-Level Utilization of Non-pharmacologic Chronic Pain Treatment and Subsequent Initiation of Long-Term Opioid Therapy.

    Science.gov (United States)

    Carey, Evan P; Nolan, Charlotte; Kerns, Robert D; Ho, P Michael; Frank, Joseph W

    2018-05-01

    Expert guidelines recommend non-pharmacologic treatments and non-opioid medications for chronic pain and recommend against initiating long-term opioid therapy (LTOT). We examined whether veterans with incident chronic pain receiving care at facilities with greater utilization of non-pharmacologic treatments and non-opioid medications are less likely to initiate LTOT. Retrospective cohort study PARTICIPANTS: Veterans receiving primary care from a Veterans Health Administration facility with incident chronic pain between 1/1/2010 and 12/31/2015 based on either of 2 criteria: (1) persistent moderate-to-severe patient-reported pain and (2) diagnoses "likely to represent" chronic pain. The independent variable was facility-level utilization of pain-related treatment modalities (non-pharmacologic, non-opioid medications, LTOT) in the prior calendar year. The dependent variable was patient-level initiation of LTOT (≥ 90 days within 365 days) in the subsequent year, adjusting for patient characteristics. Among 1,094,569 veterans with incident chronic pain from 2010 to 2015, there was wide facility-level variation in utilization of 10 pain-related treatment modalities, including initiation of LTOT (median, 16%; range, 5-32%). Veterans receiving care at facilities with greater utilization of non-pharmacologic treatments were less likely to initiate LTOT in the year following incident chronic pain. Conversely, veterans receiving care at facilities with greater non-opioid and opioid medication utilization were more likely to initiate LTOT; this association was strongest for past year facility-level LTOT initiation (adjusted rate ratio, 2.10; 95% confidence interval, 2.06-2.15, top vs. bottom quartile of facility-level LTOT initiation in prior calendar year). Facility-level utilization patterns of non-pharmacologic, non-opioid, and opioid treatments for chronic pain are associated with subsequent patient-level initiation of LTOT among veterans with incident chronic pain

  11. Initial data sets for the Schwarzschild spacetime

    International Nuclear Information System (INIS)

    Gomez-Lobo, Alfonso Garcia-Parrado; Kroon, Juan A. Valiente

    2007-01-01

    A characterization of initial data sets for the Schwarzschild spacetime is provided. This characterization is obtained by performing a 3+1 decomposition of a certain invariant characterization of the Schwarzschild spacetime given in terms of concomitants of the Weyl tensor. This procedure renders a set of necessary conditions--which can be written in terms of the electric and magnetic parts of the Weyl tensor and their concomitants--for an initial data set to be a Schwarzschild initial data set. Our approach also provides a formula for a static Killing initial data set candidate--a KID candidate. Sufficient conditions for an initial data set to be a Schwarzschild initial data set are obtained by supplementing the necessary conditions with the requirement that the initial data set possesses a stationary Killing initial data set of the form given by our KID candidate. Thus, we obtain an algorithmic procedure of checking whether a given initial data set is Schwarzschildean or not

  12. The uranium industry: long term planning for short term competition

    International Nuclear Information System (INIS)

    Vottero, X.

    2000-01-01

    Today, uranium producers face new challenges in terms of both production (new regulatory, environmental and social constraints) and market conditions (new sources of uranium supply, very low prices and tough competition). In such a context, long-term planning is not just a prerequisite to survive in the nuclear fuel cycle industry. In fact, it also contributes to sustaining nuclear electricity generation facing fierce competition from other energy sources in increasingly deregulated markets. (authors)

  13. Handbook of mechanical engineering terms

    CERN Document Server

    Ramalingam, KK

    2009-01-01

    About the Book: The Handbook of Mechanical Engineering terms contains short, precise definitions of about four thousand terms. These terms have been collected from different sources, edited and grouped under twenty six parts and given alphabetically under each part for easy reference. The book will be a source of guidance and help to the students, staff and practising engineers in understanding and updating the subject matter. Contents: The Handbook of Mechanical Engineering terms contains short, precise definitions of about four thousand terms. These terms have been collected from differ

  14. Advanced Monte Carlo procedure for the IFMIF d-Li neutron source term based on evaluated cross section data

    International Nuclear Information System (INIS)

    Simakov, S.P.; Fischer, U.; Moellendorff, U. von; Schmuck, I.; Konobeev, A.Yu.; Korovin, Yu.A.; Pereslavtsev, P.

    2002-01-01

    A newly developed computational procedure is presented for the generation of d-Li source neutrons in Monte Carlo transport calculations based on the use of evaluated double-differential d+ 6,7 Li cross section data. A new code M c DeLicious was developed as an extension to MCNP4C to enable neutronics design calculations for the d-Li based IFMIF neutron source making use of the evaluated deuteron data files. The M c DeLicious code was checked against available experimental data and calculation results of M c DeLi and MCNPX, both of which use built-in analytical models for the Li(d, xn) reaction. It is shown that M c DeLicious along with newly evaluated d+ 6,7 Li data is superior in predicting the characteristics of the d-Li neutron source. As this approach makes use of tabulated Li(d, xn) cross sections, the accuracy of the IFMIF d-Li neutron source term can be steadily improved with more advanced and validated data

  15. Advanced Monte Carlo procedure for the IFMIF d-Li neutron source term based on evaluated cross section data

    CERN Document Server

    Simakov, S P; Moellendorff, U V; Schmuck, I; Konobeev, A Y; Korovin, Y A; Pereslavtsev, P

    2002-01-01

    A newly developed computational procedure is presented for the generation of d-Li source neutrons in Monte Carlo transport calculations based on the use of evaluated double-differential d+ sup 6 sup , sup 7 Li cross section data. A new code M sup c DeLicious was developed as an extension to MCNP4C to enable neutronics design calculations for the d-Li based IFMIF neutron source making use of the evaluated deuteron data files. The M sup c DeLicious code was checked against available experimental data and calculation results of M sup c DeLi and MCNPX, both of which use built-in analytical models for the Li(d, xn) reaction. It is shown that M sup c DeLicious along with newly evaluated d+ sup 6 sup , sup 7 Li data is superior in predicting the characteristics of the d-Li neutron source. As this approach makes use of tabulated Li(d, xn) cross sections, the accuracy of the IFMIF d-Li neutron source term can be steadily improved with more advanced and validated data.

  16. Modeling long-term risk to environmental and human systems at the Hanford Nuclear Reservation: Scope and findings from the initial model

    International Nuclear Information System (INIS)

    Scott, Michael J.; Brandt, Charles A.; Bunn, Amoret L.; Engel, David W.; Eslinger, Paul W.; Miley, Terri B.; Napier, Bruce A.; Prendergast-Kennedy, Ellen L.; Nieves, Leslie A.

    2005-01-01

    The Groundwater/Vadose Zone (GW/VZ) Integration Project at the U.S. Department of Energy's Hanford Site in Washington state is currently developing the tools and supporting data to assess the cumulative impact to human and ecological health and the region's economy and cultures from waste that will remain at the Hanford Site after the site closes. This integrated system of new and legacy models and data is known as the System Assessment Capability (SAC). The environmental transport modules of the SAC modeling system provide estimates of contaminant concentrations from Hanford Site sources in a time-dependent manner in the vadose zone, groundwater, and the Columbia River and its associated sediments. The Risk/Impact Module uses these estimates of media- and time-specific concentrations to estimate potential impacts on the ecology of the Columbia River corridor, the health of persons who might live in or use the corridor or the upland Hanford environment, the local economy, and the cultural resources. Preliminary Monte Carlo realizations from the SAC modeling system demonstrate the feasibility of large-scale uncertainty analysis of the complex relationships in environmental transport on the one hand and ecological, human, cultural, and economic risk on the other. Initial impact results show successful linking of codes and very small long-term risks for the 10 radionuclides and chemicals evaluated

  17. CONTAIN code calculations of the effects on the source term of CsI to I/sub 2/ conversion due to severe hydrogen burns

    International Nuclear Information System (INIS)

    Valdez, G.D.; Williams, D.C.

    1986-01-01

    In experiments conducted at Sandia National Laboratories large amounts of elemental iodine were produced when CsI-Al 2 O 3 aerosol was exposed to hydrogen/air combustion. To evaluate some of the implications of the iodide conversion (observed to occur with up to 75% efficiency) for the severe accident source term, computational simulations of representative accident sequences were conducted with the CONTAIN code. The following conclusions can be drawn from this preliminary source term assessment: (1) If the containment sprays are inoperative during the accident, or failed by the hydrogen burn, the late-time source term is almost tripled when the iodide is converted to I 2 . (2) With the sprays active, the amount released without conversion of the CsI aerosol is 63% higher than for the case when conversion occurs. (3) For the case where CsI is converted to I 2 continued operation of the sprays reduces the release by a factor of 40, relative to the case in which the sprays fail at the time of the hydrogen burn. When there is no conversion, the reduction factor for continued spray operation is about a factor of 9, relative to the failed spray case

  18. Determination of a source term for a time fractional diffusion equation with an integral type over-determining condition

    Directory of Open Access Journals (Sweden)

    Timurkhan S. Aleroev

    2013-12-01

    Full Text Available We consider a linear heat equation involving a fractional derivative in time, with a nonlocal boundary condition. We determine a source term independent of the space variable, and the temperature distribution for a problem with an over-determining condition of integral type. We prove the existence and uniqueness of the solution, and its continuous dependence on the data.

  19. Radiological consequence evaluation of DBAs with alternative source term method for a Chinese PWR

    International Nuclear Information System (INIS)

    Li, J.X.; Cao, X.W.; Tong, L.L.; Huang, G.F.

    2012-01-01

    Highlights: ► Radiological consequence evaluation of DBAs with alternative source term method for a Chinese 900 MWe PWR has been investigated. ► Six typical DBA sequences are analyzed. ► The doses of control room, EAB and outer boundary of LPZ are acceptable. ► The differences between AST method and TID-14844 method are investigated. - Abstract: Since a large amount of fission products may releases into the environment, during the accident progression in nuclear power plants (NPPs), which is a potential hazard to public risk, the radiological consequence should be evaluated for alleviating the hazard. In most Chinese NPPs the method of TID-14844, in which the whole body and thyroid dose criteria is employed as dose criteria, is currently adopted to evaluate the radiological consequences for design-basis accidents (DBAs), but, due to the total effective dose equivalent is employed as dose criteria in alternative radiological source terms (AST) method, it is necessary to evaluate the radiological consequences for DBAs with AST method and to discuss the difference between two methods. By using an integral safety analysis code, an analytical model of the 900 MWe pressurized water reactor (PWR) is built and the radiological consequences in DBAs at control room (CR), exclusion area boundary (EAB), low population zone (LPZ) are analyzed, which includes LOCA and non-LOCA DBAs, such as fuel handling accident (FHA), rod ejection accident (REA), main steam line break (MSLB), steam generator tube rupture (SGTR), locked rotor accident (LRA) by using the guidance of the RG 1.183. The results show that the doses in CR, EAB and LPZ are acceptable compared with dose criteria in RG 1.183 and the differences between AST method and TID-14844 method are also discussed.

  20. A study on the safety of spent fuel management. Radioactive source term modelling

    Energy Technology Data Exchange (ETDEWEB)

    Chun, Kwan Sik; Lee, Hoo Keun; Park, Keun Il; Hwoang, Jung Ki; Chung, Choong Hwan [Korea Atomic Energy Research Inst., Daeduk (Korea, Republic of)

    1992-02-01

    The types and probabilities of events which may occur during the process of reception, transfer and storage of spent fuels in an away-from-reactor (AFR) spent fuel storage facility were analyzed in order to calculate the amount of radioactive material released to operation area and atmosphere, and the basic model for predicting the radioactive source-term under normal and abnormal operations were developed. Also, oxidation and dissolution of U0{sub 2} pellet was investigated to estimate the amount of radioactive materials released from spent fuel and the release characteristics of radionuclides from defected spent fuel rods was analyzed. Basic information using FIRAC code to analyze the ventilation system during fire accident was prepared and FIRIN was detached from FIRAC modified to simulate the compartment fire by personal computer. (Author).

  1. Microbial characterization for the Source-Term Waste Test Program (STTP) at Los Alamos

    International Nuclear Information System (INIS)

    Leonard, P.A.; Strietelmeier, B.A.; Pansoy-Hjelvik, M.E.; Villarreal, R.

    1999-01-01

    The effects of microbial activity on the performance of the proposed underground nuclear waste repository, the Waste Isolation Pilot Plant (WIPP) at Carlsbad, New Mexico are being studied at Los Alamos National Laboratory (LANL) as part of an ex situ large-scale experiment. Actual actinide-containing waste is being used to predict the effect of potential brine inundation in the repository in the distant future. The study conditions are meant to simulate what might exist should the underground repository be flooded hundreds of years after closure as a result of inadvertent drilling into brine pockets below the repository. The Department of Energy (DOE) selected LANL to conduct the Actinide Source-Term Waste Test Program (STTP) to confirm the predictive capability of computer models being developed at Sandia National Laboratory

  2. Microbial characterization for the Source-Term Waste Test Program (STTP) at Los Alamos

    Energy Technology Data Exchange (ETDEWEB)

    Leonard, P.A.; Strietelmeier, B.A.; Pansoy-Hjelvik, M.E.; Villarreal, R.

    1999-04-01

    The effects of microbial activity on the performance of the proposed underground nuclear waste repository, the Waste Isolation Pilot Plant (WIPP) at Carlsbad, New Mexico are being studied at Los Alamos National Laboratory (LANL) as part of an ex situ large-scale experiment. Actual actinide-containing waste is being used to predict the effect of potential brine inundation in the repository in the distant future. The study conditions are meant to simulate what might exist should the underground repository be flooded hundreds of years after closure as a result of inadvertent drilling into brine pockets below the repository. The Department of Energy (DOE) selected LANL to conduct the Actinide Source-Term Waste Test Program (STTP) to confirm the predictive capability of computer models being developed at Sandia National Laboratory.

  3. Environmental radiation safety source term evaluation program

    International Nuclear Information System (INIS)

    Moss, O.R.; Filipy, R.E.; Cannon, W.C.; Craig, D.K.

    1977-04-01

    Plutonium-238 is currently used in the form of a pure refractory oxide as a power source on a number of space vehicles that have already been or will be launched during the next few years. Although the sources are designed and built to withstand re-entry into the earth's atmosphere and impact with the earth's surface without releasing any plutonium, the possibility of such an event can never be absolutely excluded. Three separate tasks were undertaken in this study. The interactions between soils and 238 PuO 2 aerosols which might be created in a space launch about environment were examined. Aging of the plutonium-soil mixture under a humid atmosphere showed a trend toward the slow coagulation of two dilute aerosols. Studies on marine animals were conducted to assess the response of 238 PuO 2 pellets to conditions found 60 feet below the ocean surface. Ultrafilterability studies measured the solubility of 238 PuO 2 as a function of time, temperature, suspension concentration and molality of solvent

  4. Black Carbon and Sulfate Aerosols in the Arctic: Long-term Trends, Radiative Impacts, and Source Attributions

    Science.gov (United States)

    Wang, H.; Zhang, R.; Yang, Y.; Smith, S.; Rasch, P. J.

    2017-12-01

    The Arctic has warmed dramatically in recent decades. As one of the important short-lived climate forcers, aerosols affect the Arctic radiative budget directly by interfering radiation and indirectly by modifying clouds. Light-absorbing particles (e.g., black carbon) in snow/ice can reduce the surface albedo. The direct radiative impact of aerosols on the Arctic climate can be either warming or cooling, depending on their composition and location, which can further alter the poleward heat transport. Anthropogenic emissions, especially, BC and SO2, have changed drastically in low/mid-latitude source regions in the past few decades. Arctic surface observations at some locations show that BC and sulfate aerosols had a decreasing trend in the recent decades. In order to understand the impact of long-term emission changes on aerosols and their radiative effects, we use the Community Earth System Model (CESM) equipped with an explicit BC and sulfur source-tagging technique to quantify the source-receptor relationships and decadal trends of Arctic sulfate and BC and to identify variations in their atmospheric transport pathways from lower latitudes. The simulation was conducted for 36 years (1979-2014) with prescribed sea surface temperatures and sea ice concentrations. To minimize potential biases in modeled large-scale circulations, wind fields in the simulation are nudged toward an atmospheric reanalysis dataset, while atmospheric constituents including water vapor, clouds, and aerosols are allowed to evolve according to the model physics. Both anthropogenic and open fire emissions came from the newly released CMIP6 datasets, which show strong regional trends in BC and SO2 emissions during the simulation time period. Results show that emissions from East Asia and South Asia together have the largest contributions to Arctic sulfate and BC concentrations in the upper troposphere, which have an increasing trend. The strong decrease in emissions from Europe, Russia and

  5. Behavioral Initiatives in Broad Perspective.

    Science.gov (United States)

    California Univ., Los Angeles. Center for Mental Health in Schools.

    This booklet is a technical assistance sampler addressing the issues of student misbehavior, discipline problems, and behavioral initiatives. The term behavioral initiative is defined, disciplining children with disabilities is discussed, and a cautionary note concerning ignoring students' reasons for misbehavior is presented. A brief entitled…

  6. Open Source Business Solutions

    Directory of Open Access Journals (Sweden)

    Ion IVAN

    2008-01-01

    Full Text Available This analyses the Open source movement. Open source development process and management is seen different from the classical point of view. This focuses on characteristics and software market tendencies for the main Open source initiatives. It also points out the labor market future evolution for the software developers.

  7. Light-initiated detonation systems

    Science.gov (United States)

    Cooper, Stafford S.; Malone, Philip G.; Bartholomew, Stephen W.; Necker, William J.

    1986-09-01

    Numerous light sources could be employed in detonation systems, but lasers have the most efficient coupling to optical fibers and can generate energetic light pulses required for detonation. Flash lamp-pumped, solid state lasers are presently the most useful light source for explosive initiation. Laser diodes in current production cannot generate enough energy for practical applications. The most useful optical fiber for blast line application is a step index fiber with a large core-to-cladding ratio. The large core minimizes energy losses due to misalignment core of fibers in connectors. Couplers that involve mechanically crimped connectors and cleaved fibers, rather than the epoxy-cemented connectors with polished fibers, provide superior energy transmission due to the reduced carbonization at the fiber end. Detonators for optical initiation systems are similar in basic construction to those employed in electrical initiation systems. Explosive and pyrotechnic charges can also be similar. Either primary or secondary explosives can be initiated in present laser-based systems. Two laser detonation systems are presently accessible; a multiple-shot laser with a single-shot, single fiber system designed for use with detonators containing primary explosives. Additional research related to development of low-energy, photoreactive detonators, continuity checking techniques and improved connectors and fibers can produce significant improvements in presently fielded systems.

  8. A Mechanistic Source Term Calculation for a Metal Fuel Sodium Fast Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Grabaskas, David; Bucknor, Matthew; Jerden, James

    2017-06-26

    A mechanistic source term (MST) calculation attempts to realistically assess the transport and release of radionuclides from a reactor system to the environment during a specific accident sequence. The U.S. Nuclear Regulatory Commission (NRC) has repeatedly stated its expectation that advanced reactor vendors will utilize an MST during the U.S. reactor licensing process. As part of a project to examine possible impediments to sodium fast reactor (SFR) licensing in the U.S., an analysis was conducted regarding the current capabilities to perform an MST for a metal fuel SFR. The purpose of the project was to identify and prioritize any gaps in current computational tools, and the associated database, for the accurate assessment of an MST. The results of the study demonstrate that an SFR MST is possible with current tools and data, but several gaps exist that may lead to possibly unacceptable levels of uncertainty, depending on the goals of the MST analysis.

  9. Low-level radioactive waste source term model development and testing: Topical report

    International Nuclear Information System (INIS)

    Sullivan, T.M.; Kempf, C.R.; Suen, C.J.; Mughabghab, S.M.

    1988-08-01

    The Low-Level Waste Source Term Evaluation Project has the objective to develop a system model capable of predicting radionuclide release rates from a shallow land burial facility. The previous topical report for this project discussed the framework and methodology for developing a system model and divided the problem into four compartments: water flow, container degradation, waste form leaching, and radionuclide transport. Each of these compartments is described by submodels which will be coupled into the system model. From February 1987 to March 1988, computer models have been selected to predict water flow (FEMWATER) and radionuclide transport (FEMWASTE) and separate models have been developed to predict pitting corrosion of steel containers and leaching from porous waste forms contained in corrodible containers. This report discusses each of the models in detail and presents results obtained from applying the models to shallow land burial trenches over a range of expected conditions. 68 refs., 34 figs., 14 tabs

  10. Constraints on equivalent elastic source models from near-source data

    International Nuclear Information System (INIS)

    Stump, B.

    1993-01-01

    A phenomenological based seismic source model is important in quantifying the important physical processes that affect the observed seismic radiation in the linear-elastic regime. Representations such as these were used to assess yield effects on seismic waves under a Threshold Test Ban Treaty and to help transport seismic coupling experience at one test site to another. These same characterizations in a non-proliferation environment find applications in understanding the generation of the different types of body and surface waves from nuclear explosions, single chemical explosions, arrays of chemical explosions used in mining, rock bursts and earthquakes. Seismologists typically begin with an equivalent elastic representation of the source which when convolved with the propagation path effects produces a seismogram. The Representation Theorem replaces the true source with an equivalent set of body forces, boundary conditions or initial conditions. An extension of this representation shows the equivalence of the body forces, boundary conditions and initial conditions and replaces the source with a set of force moments, the first degree moment tensor for a point source representation. The difficulty with this formulation, which can completely describe the observed waveforms when the propagation path effects are known, is in the physical interpretation of the actual physical processes acting in the source volume. Observational data from within the source region, where processes are often nonlinear, linked to numerical models of the important physical processes in this region are critical to a unique physical understanding of the equivalent elastic source function

  11. Chemical Dynamics at the Advanced Light Source

    International Nuclear Information System (INIS)

    Baer, T.; Berrah, N.; Fadley, C.; Moore, C.B.; Neumark, D.M.; Ng, C.Y.; Ruscic, B.; Smith, N.V.; Suits, A.G.; Wodtke, A.M.

    1999-01-01

    A day-long retreat was held January 15, 1999 to chart the future directions for chemical dynamics studies at the Advanced Light Source. This represents an important period for the Chemical Dynamics Beamline, as the hardware is well-developed, most of the initial experimental objectives have been realized and the mission is now to identify the future scientific priorities for the beamline and attract users of the highest caliber. To this end, we have developed a detailed scientific program for the near term; identified and prioritized the long range scientific opportunities, identified essential new hardware, and outlined an aggressive outreach program to involve the chemical physics community

  12. Unilateral initiatives

    International Nuclear Information System (INIS)

    Anon.

    1988-01-01

    This paper reports on arms control which is generally thought of in terms of formal negotiations with an opponent, with the resulting agreements embodied in a treaty. This is not surprising, since arms control discussions between opponents are both important and politically visible. There are, however, strong reasons for countries to consider and frequently take unilateral initiatives. To do so is entirely consistent with the established major precepts of arms control which state that arms control is designed to reduce the risk of war, the costs of preparing for war, and the death and destruction if war should come. Unilateral initiatives on what weapons are purchased, which ones are eliminated and how forces are deployed can all relate to these objectives. There are two main categories of motives for unilateral initiatives in arms control. In one category, internal national objectives are the dominant, often sole, driving force; the initiative is undertaken for our own good

  13. Toward a Mechanistic Source Term in Advanced Reactors: A Review of Past U.S. SFR Incidents, Experiments, and Analyses

    Energy Technology Data Exchange (ETDEWEB)

    Bucknor, Matthew; Brunett, Acacia J.; Grabaskas, David

    2016-04-17

    In 2015, as part of a Regulatory Technology Development Plan (RTDP) effort for sodium-cooled fast reactors (SFRs), Argonne National Laboratory investigated the current state of knowledge of source term development for a metal-fueled, pool-type SFR. This paper provides a summary of past domestic metal-fueled SFR incidents and experiments and highlights information relevant to source term estimations that were gathered as part of the RTDP effort. The incidents described in this paper include fuel pin failures at the Sodium Reactor Experiment (SRE) facility in July of 1959, the Fermi I meltdown that occurred in October of 1966, and the repeated melting of a fuel element within an experimental capsule at the Experimental Breeder Reactor II (EBR-II) from November 1967 to May 1968. The experiments described in this paper include the Run-Beyond-Cladding-Breach tests that were performed at EBR-II in 1985 and a series of severe transient overpower tests conducted at the Transient Reactor Test Facility (TREAT) in the mid-1980s.

  14. Initial Results from the Survey of Organizational Research Climates (SOuRCe) in the U.S. Department of Veterans Affairs Healthcare System

    Science.gov (United States)

    Martinson, Brian C.; Nelson, David; Hagel-Campbell, Emily; Mohr, David; Charns, Martin P.; Bangerter, Ann; Thrush, Carol R.; Ghilardi, Joseph R.; Bloomfield, Hanna; Owen, Richard; Wells, James A.

    2016-01-01

    Background In service to its core mission of improving the health and well-being of veterans, Veterans Affairs (VA) leadership is committed to supporting research best practices in the VA. Recognizing that the behavior of researchers is influenced by the organizational climates in which they work, efforts to assess the integrity of research climates and share such information with research leadership in VA may be one way to support research best practices. The Survey of Organizational Research Climate (SOuRCe) is the first validated survey instrument specifically designed to assess the organizational climate of research integrity in academic research organizations. The current study reports on an initiative to use the SOuRCe in VA facilities to characterize the organizational research climates and pilot test the effectiveness of using SOuRCe data as a reporting and feedback intervention tool. Methods We administered the SOuRCe using a cross-sectional, online survey, with mailed follow-up to non-responders, of research-engaged employees in the research services of a random selection of 42 VA facilities (e.g., Hospitals/Stations) believed to employ 20 or more research staff. We attained a 51% participation rate, yielding more than 5,200 usable surveys. Results We found a general consistency in organizational research climates across a variety of sub-groups in this random sample of research services in the VA. We also observed similar SOuRCe scale score means, relative rankings of these scales and their internal reliability, in this VA-based sample as we have previously documented in more traditional academic research settings. Results also showed more substantial variability in research climate scores within than between facilities in the VA research service as reflected in meaningful subgroup differences. These findings suggest that the SOuRCe is suitable as an instrument for assessing the research integrity climates in VA and that the tool has similar patterns of

  15. Initial Results from the Survey of Organizational Research Climates (SOuRCe) in the U.S. Department of Veterans Affairs Healthcare System.

    Science.gov (United States)

    Martinson, Brian C; Nelson, David; Hagel-Campbell, Emily; Mohr, David; Charns, Martin P; Bangerter, Ann; Thrush, Carol R; Ghilardi, Joseph R; Bloomfield, Hanna; Owen, Richard; Wells, James A

    2016-01-01

    In service to its core mission of improving the health and well-being of veterans, Veterans Affairs (VA) leadership is committed to supporting research best practices in the VA. Recognizing that the behavior of researchers is influenced by the organizational climates in which they work, efforts to assess the integrity of research climates and share such information with research leadership in VA may be one way to support research best practices. The Survey of Organizational Research Climate (SOuRCe) is the first validated survey instrument specifically designed to assess the organizational climate of research integrity in academic research organizations. The current study reports on an initiative to use the SOuRCe in VA facilities to characterize the organizational research climates and pilot test the effectiveness of using SOuRCe data as a reporting and feedback intervention tool. We administered the SOuRCe using a cross-sectional, online survey, with mailed follow-up to non-responders, of research-engaged employees in the research services of a random selection of 42 VA facilities (e.g., Hospitals/Stations) believed to employ 20 or more research staff. We attained a 51% participation rate, yielding more than 5,200 usable surveys. We found a general consistency in organizational research climates across a variety of sub-groups in this random sample of research services in the VA. We also observed similar SOuRCe scale score means, relative rankings of these scales and their internal reliability, in this VA-based sample as we have previously documented in more traditional academic research settings. Results also showed more substantial variability in research climate scores within than between facilities in the VA research service as reflected in meaningful subgroup differences. These findings suggest that the SOuRCe is suitable as an instrument for assessing the research integrity climates in VA and that the tool has similar patterns of results that have been

  16. Initial Results from the Survey of Organizational Research Climates (SOuRCe in the U.S. Department of Veterans Affairs Healthcare System.

    Directory of Open Access Journals (Sweden)

    Brian C Martinson

    Full Text Available In service to its core mission of improving the health and well-being of veterans, Veterans Affairs (VA leadership is committed to supporting research best practices in the VA. Recognizing that the behavior of researchers is influenced by the organizational climates in which they work, efforts to assess the integrity of research climates and share such information with research leadership in VA may be one way to support research best practices. The Survey of Organizational Research Climate (SOuRCe is the first validated survey instrument specifically designed to assess the organizational climate of research integrity in academic research organizations. The current study reports on an initiative to use the SOuRCe in VA facilities to characterize the organizational research climates and pilot test the effectiveness of using SOuRCe data as a reporting and feedback intervention tool.We administered the SOuRCe using a cross-sectional, online survey, with mailed follow-up to non-responders, of research-engaged employees in the research services of a random selection of 42 VA facilities (e.g., Hospitals/Stations believed to employ 20 or more research staff. We attained a 51% participation rate, yielding more than 5,200 usable surveys.We found a general consistency in organizational research climates across a variety of sub-groups in this random sample of research services in the VA. We also observed similar SOuRCe scale score means, relative rankings of these scales and their internal reliability, in this VA-based sample as we have previously documented in more traditional academic research settings. Results also showed more substantial variability in research climate scores within than between facilities in the VA research service as reflected in meaningful subgroup differences. These findings suggest that the SOuRCe is suitable as an instrument for assessing the research integrity climates in VA and that the tool has similar patterns of results that

  17. Two tests of electric fields, second-order in source-velocity terms of closed, steady currents: (1) an electron beam; (2) a superconducting coil

    International Nuclear Information System (INIS)

    Kenyon, C.S.

    1980-01-01

    One particular prediction of Maxwell's theory that has been previously neglected is that the motion of charges traveling in closed loops produces no constant electric fields. This study presents and analyzes the results of two new experiments designed to test for second-order, source-velocity electric fields from steady, closed currents and analyzes another experiment in light of these fields. The first experiment employed an electron beam. The second used a niobium-titanium coil designed so that the voltage measurement configuration could be easily switched from a Faraday to a non-faraday configuration between sets of runs. The implications of the observation of a null charge on magnetically suspended superconducting spheres vis-a-vis the second-order, source-velocity fields were discussed as the third case. The observation of a null potential corresponding to a null effective charge from a hypothetical velocity-squared field in both the beam and the coil experiment placed the upper bound on a field term at 0.02 with respect a Coulomb term. An observed null charge on the suspended spheres reduced this bound to 0.001. Such an upper bound is strong evidence against alternative theories predicting a relative contribution of the order of unity for a simple velocity-squared term. A simple velocity-squared electric field would be indistinguishable from a velocity-squared charge variation. The latter test limits such a charge variation to 0.001 of the total charge. The suspended-spheres test allowed the previously neglected issue of a general second-order, source-velocity electric field to be addressed. The observed null charge in this test contradicts and thus eliminates a hypothesized, general, electric field expression containing three second-order, source-velocity terms

  18. Source term boundary adaptive estimation in a first-order 1D hyperbolic PDE: Application to a one loop solar collector through

    KAUST Repository

    Mechhoud, Sarra; Laleg-Kirati, Taous-Meriem

    2016-01-01

    In this paper, boundary adaptive estimation of solar radiation in a solar collector plant is investigated. The solar collector is described by a 1D first-order hyperbolic partial differential equation where the solar radiation models the source term

  19. Modeling of Radiotherapy Linac Source Terms Using ARCHER Monte Carlo Code: Performance Comparison for GPU and MIC Parallel Computing Devices

    Science.gov (United States)

    Lin, Hui; Liu, Tianyu; Su, Lin; Bednarz, Bryan; Caracappa, Peter; Xu, X. George

    2017-09-01

    Monte Carlo (MC) simulation is well recognized as the most accurate method for radiation dose calculations. For radiotherapy applications, accurate modelling of the source term, i.e. the clinical linear accelerator is critical to the simulation. The purpose of this paper is to perform source modelling and examine the accuracy and performance of the models on Intel Many Integrated Core coprocessors (aka Xeon Phi) and Nvidia GPU using ARCHER and explore the potential optimization methods. Phase Space-based source modelling for has been implemented. Good agreements were found in a tomotherapy prostate patient case and a TrueBeam breast case. From the aspect of performance, the whole simulation for prostate plan and breast plan cost about 173s and 73s with 1% statistical error.

  20. Long-term follow-up of radiation accident patients in Peru: Review of two cases

    International Nuclear Information System (INIS)

    Barriga, L. E.; Zaharia, M.; Pinillos, L.; Moscol, A.; Heredia, A.; Sarria, G.; Marquina, J.; Barriga, O.; Picon, C.

    2012-01-01

    Overexposure to radioactive sources used in radiotherapy or industrial radiography may result in severe health consequences. This report assesses the initial clinical status and the medical and psychological long-term follow-up of two radiation accident patients from Peru during the mid-to-late 1990's: one patient exposed to a radiotherapy 60 Co source in Arequipa, the other patient to a 192 Ir source in Yanango. Commonalities and differences are described. The main causes in both accidents were human error and the failure to apply appropriate safety guidelines and standard operating procedures. Education and training of the personnel working with radiation sources are essential to prevent accidents. The experience gained from the medical management of the two patients is valuable for future treatment of such patients. (authors)

  1. Mass conservation for instantaneous sources in FEM3 simulations of material dispersion

    International Nuclear Information System (INIS)

    Rodean, H.C.

    1987-11-01

    This report presents the results of a systematic study in which it is shown that the numerical integration errors in determining material mass content are negligible; the material phase-change model by itself is not a cause of material mass variation; and a linear relation between fractional mass change and fractional density change at the source center for given mesh and source geometries exists over a range of values from 10 -5 to 10 -1 . This suggests that the omission of the ∂ rho/∂t term from the mass conservation equation is the cause of the observed non-conservation of mass by FEM3. It is shown that these mass variations can be minimized by minimizing the initial density gradients in the source region. 5 refs., 18 figs., 4 tabs

  2. Neural system for updating object working memory from different sources: sensory stimuli or long-term memory.

    Science.gov (United States)

    Roth, Jennifer K; Courtney, Susan M

    2007-11-15

    Working memory (WM) is the active maintenance of currently relevant information so that it is available for use. A crucial component of WM is the ability to update the contents when new information becomes more relevant than previously maintained information. New information can come from different sources, including from sensory stimuli (SS) or from long-term memory (LTM). Updating WM may involve a single neural system regardless of source, distinct systems for each source, or a common network with additional regions involved specifically in sensory or LTM processes. The current series of experiments indicates that a single fronto-parietal network (including supplementary motor area, parietal, left inferior frontal junction, middle frontal gyrus) is active in updating WM regardless of the source of information. Bilateral cuneus was more active during updating WM from LTM than updating from SS, but the activity in this region was attributable to recalling information from LTM regardless of whether that information was to be entered into WM for future use or not. No regions were found to be more active during updating from SS than updating from LTM. Functional connectivity analysis revealed that different regions within this common update network were differentially more correlated with visual processing regions when participants updated from SS, and more correlated with LTM processing regions when participants updated from the contents of LTM. These results suggest that a single neural mechanism is responsible for controlling the contents of WM regardless of whether that information originates from a sensory stimulus or from LTM. This network of regions involved in updating WM interacts with the rest of the brain differently depending on the source of newly relevant information.

  3. Accident source terms for pressurized water reactors with high-burnup cores calculated using MELCOR 1.8.5.

    Energy Technology Data Exchange (ETDEWEB)

    Gauntt, Randall O.; Powers, Dana Auburn; Ashbaugh, Scott G.; Leonard, Mark Thomas; Longmire, Pamela

    2010-04-01

    In this study, risk-significant pressurized-water reactor severe accident sequences are examined using MELCOR 1.8.5 to explore the range of fission product releases to the reactor containment building. Advances in the understanding of fission product release and transport behavior and severe accident progression are used to render best estimate analyses of selected accident sequences. Particular emphasis is placed on estimating the effects of high fuel burnup in contrast with low burnup on fission product releases to the containment. Supporting this emphasis, recent data available on fission product release from high-burnup (HBU) fuel from the French VERCOR project are used in this study. The results of these analyses are treated as samples from a population of accident sequences in order to employ approximate order statistics characterization of the results. These trends and tendencies are then compared to the NUREG-1465 alternative source term prescription used today for regulatory applications. In general, greater differences are observed between the state-of-the-art calculations for either HBU or low-burnup (LBU) fuel and the NUREG-1465 containment release fractions than exist between HBU and LBU release fractions. Current analyses suggest that retention of fission products within the vessel and the reactor coolant system (RCS) are greater than contemplated in the NUREG-1465 prescription, and that, overall, release fractions to the containment are therefore lower across the board in the present analyses than suggested in NUREG-1465. The decreased volatility of Cs2MoO4 compared to CsI or CsOH increases the predicted RCS retention of cesium, and as a result, cesium and iodine do not follow identical behaviors with respect to distribution among vessel, RCS, and containment. With respect to the regulatory alternative source term, greater differences are observed between the NUREG-1465 prescription and both HBU and LBU predictions than exist between HBU and LBU

  4. Using an open-source PACS virtual machine for a digital angiography unit: methods and initial impressions.

    Science.gov (United States)

    Kagadis, George C; Alexakos, Christos; Langer, Steve G; French, Todd

    2012-02-01

    The productivity gains, diagnostic benefit, and enhanced data availability to clinicians enabled by picture archiving and communication systems (PACS) are no longer in doubt. However, commercial PACS offerings are often extremely expensive initially and require ongoing support contracts with vendors to maintain them. Recently, several open-source offerings have become available that put PACS within reach of more users. However, they can be resource-intensive to install and assure that they have room for future growth--both for computational and storage capacity. An alternate approach, which we describe herein, is to use PACS built on virtual machines which can be moved from smaller to larger hardware as needed in a just-in-time manner. This leverages the cost benefits of Moore's Law for both storage and compute costs. We describe the approach and current results in this paper.

  5. Methods to prevent the source term of methyl lodide during a core melt accident

    Energy Technology Data Exchange (ETDEWEB)

    Karhu, A. [VTT Energy (Finland)

    1999-11-01

    The purpose of this literature review is to gather available information of the methods to prevent a source term of methyl iodide during a core melt accident. The most widely studied methods for nuclear power plants include the impregnated carbon filters and alkaline additives and sprays. It is indicated that some deficiencies of these methods may emerge. More reactive impregnants and additives could make a great improvement. As a new method in the field of nuclear applications, the potential of transition metals to decompose methyl iodide, is introduced in this review. This area would require an additional research, which could elucidate the remaining questions of the reactions. The ionization of the gaseous methyl iodide by corona-discharge reactors is also shortly described. (au)

  6. Electrical initiation of an energetic nanolaminate film

    Science.gov (United States)

    Tringe, Joseph W.; Gash, Alexander E.; Barbee, Jr., Troy W.

    2010-03-30

    A heating apparatus comprising an energetic nanolaminate film that produces heat when initiated, a power source that provides an electric current, and a control that initiates the energetic nanolaminate film by directing the electric current to the energetic nanolaminate film and joule heating the energetic nanolaminate film to an initiation temperature. Also a method of heating comprising providing an energetic nanolaminate film that produces heat when initiated, and initiating the energetic nanolaminate film by directing an electric current to the energetic nanolaminate film and joule heating the energetic nanolaminate film to an initiation temperature.

  7. Modeling of Radiotherapy Linac Source Terms Using ARCHER Monte Carlo Code: Performance Comparison for GPU and MIC Parallel Computing Devices

    Directory of Open Access Journals (Sweden)

    Lin Hui

    2017-01-01

    Full Text Available Monte Carlo (MC simulation is well recognized as the most accurate method for radiation dose calculations. For radiotherapy applications, accurate modelling of the source term, i.e. the clinical linear accelerator is critical to the simulation. The purpose of this paper is to perform source modelling and examine the accuracy and performance of the models on Intel Many Integrated Core coprocessors (aka Xeon Phi and Nvidia GPU using ARCHER and explore the potential optimization methods. Phase Space-based source modelling for has been implemented. Good agreements were found in a tomotherapy prostate patient case and a TrueBeam breast case. From the aspect of performance, the whole simulation for prostate plan and breast plan cost about 173s and 73s with 1% statistical error.

  8. Sustainable Agricultural Marketing Initiatives

    Directory of Open Access Journals (Sweden)

    Hakan Adanacıoğlu

    2015-07-01

    Full Text Available Sustainable marketing is a holistic approach that puts equal emphasis on environmental, social equity, and economic concerns in the development of marketing strategies. The purpose of the study is to examine and discuss the sustainable agricultural marketing initiatives practiced throughout the World and Turkey, and to put forth suggestions to further improve the performance of agricultural marketing initiatives in Turkey. Some of the sustainable agricultural marketing initiatives practiced around the world are carried out through civil organizations. Furthermore; some of these initiatives have also launched by farmers, consumers, food processors and retailers. The long-term strategies to increase these initiatives should be determined due to the fact that examples of successful sustainable agricultural marketing initiatives are inadequate and cannot be spread in Turkey. In this context, first of all, the supports provided by the government to improve agricultural marketing systems, such as EU funds for rural development should be compatible with the goals of sustainable marketing. For this purpose, it should be examined whether all proposed projects related to agricultural marketing meet the social, economic, and environmental principles of sustainable marketing. It is important that supporting organizations, especially civil society organisations, should take an active role for faster dissemination and adoption of sustainable agricultural marketing practices in Turkey. These organizations may provide technical assistance in preparing successful project proposals and training to farm groups. In addition, the other organizations, such as local administrations, producers' associations, cooperatives, can contribute to the success of sustainable agricultural marketing initiatives. The use of direct marketing strategies and vertical integration attempts in sustainable agricultural marketing initiatives that will likely be implemented in Turkey is

  9. STEPS: source term estimation based on plant status phase 0 - the technical specifications of the containment module

    International Nuclear Information System (INIS)

    Vamanu, D.V.

    1998-01-01

    In the framework of Project RODOS (Real-Time On-Line Decision Support System for Nuclear Emergencies in Europe), the European Atomic Energy Community (EAEC) of the Commission of the European Communities has commissioned the development of a unified concept, body of knowledge, models and software package meant to assist the evaluation of the source term of severe nuclear accidents in light water reactors of the types prevailing on the Continent. Code-named STEPS, for 'Source Term Estimation based on Plant Status', the project has evolved as Contract RODOS D (FI4P-CT96-0048), between EAEC and consortium of expert European centres including Commissariat a l'Energie Atomique, Institut de Protection et de Surete Nucleaire, (CEA-DPI-SEAC) as Coordinator and Forschungszentrum Karlsruhe GmbH (FZK-INR), the Finnish Centre for Radiation and Nuclear Safety, (STUK-NSD), the Technical Research Centre of Finland, Energy, Nuclear Energy (VTT-ET-NE), and Eidgenossische Technische Hochschule - ETH Zurich, Centre of Excellence (ETH-CERS) as Contractors. For the Phase 0 of the project, an IFIN-HH expert has been assigned by ETH-CERS to develop the Technical Specifications of the delivery component of the intended STEPS package, the CONTAINMENT Module. Sponsored by ETH-CERS headquarters in Zurich, the work was done on the premises and with the logistic support of CEA D PI-SEAC at Fontenay-aux-Roses, with the feedback processing and computer code development subsequently performed in Bucharest. The Technical Specifications of the STEPS CONTAINMENT Module were guided by specific terms of reference, including: (i) the capability of the software to function as a source term interface between targeted nuclear power plants and the RODOS System; (ii) the comparable capability of the system to be operated as a stand-alone assessment and decision support tool for a comprehensive variety of plants, nuclear emergency classes. On the technical side, the specifications had to focus on the possible

  10. Economical comparison of imported energy sources in terms of long-term production planning

    International Nuclear Information System (INIS)

    Gungor, Z.

    1999-01-01

    In this paper, the Turkish energy production sector is studied and power plants fueled by natural gas, imported coal and nuclear power are compared in terms of long-term (1996-2010) production economy. A net present value is used for comparing nuclear, coal and natural gas power plants. A scenario approach is utilized in establishing the effects of different factors, such as inflation rate, unit of investment costs, load factor change, discount rate and fuel price changes. Six different scenarios of interest are developed and discussed. The study ends with conclusions and recommendations based on a study of a reference scenario and alternative scenarios. (author)

  11. The use of nonlinear regression analysis for integrating pollutant concentration measurements with atmospheric dispersion modeling for source term estimation

    International Nuclear Information System (INIS)

    Edwards, L.L.; Freis, R.P.; Peters, L.G.; Gudiksen, P.H.; Pitovranov, S.E.

    1993-01-01

    The accuracy associated with assessing the environmental consequences of an accidental release of radioactivity is highly dependent on the knowledge of the source term characteristics, which are generally poorly known. The development of an automated numerical technique that integrates the radiological measurements with atmospheric dispersion modeling for more accurate source term estimation is reported. Often, this process of parameter estimation is performed by an emergency response assessor, who takes an intelligent first guess at the model parameters, then, comparing the model results with whatever measurements are available, makes an intuitive, informed next guess of the model parameters. This process may be repeated any number of times until the assessor feels that the model results are reasonable in terms of the measured observations. A new approach, based on a nonlinear least-squares regression scheme coupled with the existing Atmospheric Release Advisory Capability three-dimensional atmospheric dispersion models, is to supplement the assessor's intuition with automated mathematical methods that do not significantly increase the response time of the existing predictive models. The viability of the approach is evaluated by estimation of the known SF 6 tracer release rates associated with the Mesoscale Atmospheric Transport Studies tracer experiments conducted at the Savannah River Laboratory during 1983. These 19 experiments resulted in 14 successful, separate tracer releases with sampling of the tracer plumes along the cross-plume arc situated ∼30 km from the release site

  12. Panorama 2014 - Short term trends in the gas industry

    International Nuclear Information System (INIS)

    Lecarpentier, Armelle

    2013-12-01

    Due to sustained competition between energy sources and an economic and geopolitical climate that is still unstable, gas growth has slowed. The year 2013 looks very mixed for the gas industry, particularly on the upstream side. Constraints on the supply of gas and the increased dependence on imports in consumer markets increase the vulnerability of the gas markets to the vagaries of geopolitical risks and result in tensions on the international market. In an environment full of uncertainties about future prices and contractual terms, investors are slow to initiate the projects necessary for a global gas balance in this decade. (author)

  13. Proposal for implementation of alternative source term in the nuclear power plant of Laguna Verde; Propuesta de implementacion del termino fuente alternativo en la central nuclear Laguna Verde

    Energy Technology Data Exchange (ETDEWEB)

    Bazan L, A.; Lopez L, M.; Vargas A, A.; Cardenas J, J. B. [Comision Federal de Electricidad, Central Nucleoelectrica Laguna Verde, Km. 7.5 Carretera Veracruz-Medellin, Dos Bocas, Veracruz (Mexico)], e-mail: ariadna.bazan@cfe.gob.mx

    2009-10-15

    In 2010 the nuclear power plant of Laguna Verde will implement the extended power upbeat in both units of the plant. Agree with methodology of NEDC-33004P-A, (constant pressure power up rate), and the source term of core, for accidents evaluations, were increased in proportion to the ratio of power level. This means that for the case of a design basis accident of loss of coolant an increase of power of 15% originated an increase of 15% in dose to main control room. Using the method of NEDC-33004P-A to extended power upbeat conditions was determined that the dose value to main control room is very near to regulatory limit established by SRP 6.4. By the above and in order to recover the margin, the nuclear power plant of Laguna Verde will calculate an alternative source term following the criteria established in RG 1.183 (alternative radiological source term for evaluating DBA at nuclear power reactor). This approach also have a more realistic dose value using the criterion of 10-CFR-50.67, in addition is predicted to get the benefit of additional operational flexibilities. This paper present the proposal of implementing the alternative source term in Laguna Verde. (Author)

  14. Reducing Uncontrolled Radioactive Sources through Tracking and Training: US Environmental Protection Agency Initiatives

    Energy Technology Data Exchange (ETDEWEB)

    Kopsick, D.A., E-mail: kopsick.deborah@epa.gov [US Environmental Protection Agency, Washington, DC (United States)

    2011-07-15

    The international metal processing industries are very concerned about the importation of scrap metal contaminated with radioactive materials. When radioactive sources fall out of regulatory control, improper handling can cause serious injury and death. There is no one way to address this problem and various US governmental and industry entities have developed radiation source control programmes that function within their authorities. The US Environmental Protection Agency's (EPA) mission is to protect public health and the environment. To ensure this protection, EPA's approach to orphan sources in scrap metal has focused on regaining control of lost sources and preventing future losses. EPA has accomplished this through a number of avenues including training development, product stewardship, identification of non-radiation source alternatives, physical tagging of sources, field testing of innovative radiation detection instrumentation and development of international best practices. In order to achieve its goal of enhanced control on contaminated scrap metal and orphaned radioactive sources, EPA has forged alliances with the metals industry, other Federal agencies, state governments and the IAEA. (author)

  15. Very long-term sequelae of craniopharyngioma.

    Science.gov (United States)

    Wijnen, Mark; van den Heuvel-Eibrink, Marry M; Janssen, Joseph A M J L; Catsman-Berrevoets, Coriene E; Michiels, Erna M C; van Veelen-Vincent, Marie-Lise C; Dallenga, Alof H G; van den Berge, J Herbert; van Rij, Carolien M; van der Lely, Aart-Jan; Neggers, Sebastian J C M M

    2017-06-01

    Studies investigating long-term health conditions in patients with craniopharyngioma are limited by short follow-up durations and generally do not compare long-term health effects according to initial craniopharyngioma treatment approach. In addition, studies comparing long-term health conditions between patients with childhood- and adult-onset craniopharyngioma report conflicting results. The objective of this study was to analyse a full spectrum of long-term health effects in patients with craniopharyngioma according to initial treatment approach and age group at craniopharyngioma presentation. Cross-sectional study based on retrospective data. We studied a single-centre cohort of 128 patients with craniopharyngioma treated from 1980 onwards (63 patients with childhood-onset disease). Median follow-up since craniopharyngioma presentation was 13 years (interquartile range: 5-23 years). Initial craniopharyngioma treatment approaches included gross total resection ( n  = 25), subtotal resection without radiotherapy ( n  = 44), subtotal resection with radiotherapy ( n  = 25), cyst aspiration without radiotherapy ( n  = 8), and 90 Yttrium brachytherapy ( n  = 21). Pituitary hormone deficiencies (98%), visual disturbances (75%) and obesity (56%) were the most common long-term health conditions observed. Different initial craniopharyngioma treatment approaches resulted in similar long-term health effects. Patients with childhood-onset craniopharyngioma experienced significantly more growth hormone deficiency, diabetes insipidus, panhypopituitarism, morbid obesity, epilepsy and psychiatric conditions compared with patients with adult-onset disease. Recurrence-/progression-free survival was significantly lower after initial craniopharyngioma treatment with cyst aspiration compared with other therapeutic approaches. Survival was similar between patients with childhood- and adult-onset craniopharyngioma. Long-term health conditions were comparable after

  16. Absolute measurement of LDR brachytherapy source emitted power: Instrument design and initial measurements.

    Science.gov (United States)

    Malin, Martha J; Palmer, Benjamin R; DeWerd, Larry A

    2016-02-01

    Energy-based source strength metrics may find use with model-based dose calculation algorithms, but no instruments exist that can measure the energy emitted from low-dose rate (LDR) sources. This work developed a calorimetric technique for measuring the power emitted from encapsulated low-dose rate, photon-emitting brachytherapy sources. This quantity is called emitted power (EP). The measurement methodology, instrument design and performance, and EP measurements made with the calorimeter are presented in this work. A calorimeter operating with a liquid helium thermal sink was developed to measure EP from LDR brachytherapy sources. The calorimeter employed an electrical substitution technique to determine the power emitted from the source. The calorimeter's performance and thermal system were characterized. EP measurements were made using four (125)I sources with air-kerma strengths ranging from 2.3 to 5.6 U and corresponding EPs of 0.39-0.79 μW, respectively. Three Best Medical 2301 sources and one Oncura 6711 source were measured. EP was also computed by converting measured air-kerma strengths to EPs through Monte Carlo-derived conversion factors. The measured EP and derived EPs were compared to determine the accuracy of the calorimeter measurement technique. The calorimeter had a noise floor of 1-3 nW and a repeatability of 30-60 nW. The calorimeter was stable to within 5 nW over a 12 h measurement window. All measured values agreed with derived EPs to within 10%, with three of the four sources agreeing to within 4%. Calorimeter measurements had uncertainties ranging from 2.6% to 4.5% at the k = 1 level. The values of the derived EPs had uncertainties ranging from 2.9% to 3.6% at the k = 1 level. A calorimeter capable of measuring the EP from LDR sources has been developed and validated for (125)I sources with EPs between 0.43 and 0.79 μW.

  17. Analysis of accident sequences and source terms at treatment and storage facilities for waste generated by US Department of Energy waste management operations

    Energy Technology Data Exchange (ETDEWEB)

    Mueller, C.; Nabelssi, B.; Roglans-Ribas, J.; Folga, S.; Policastro, A.; Freeman, W.; Jackson, R.; Mishima, J.; Turner, S.

    1996-12-01

    This report documents the methodology, computational framework, and results of facility accident analyses performed for the US Department of Energy (DOE) Waste Management Programmatic Environmental Impact Statement (WM PEIS). The accident sequences potentially important to human health risk are specified, their frequencies assessed, and the resultant radiological and chemical source terms evaluated. A personal-computer-based computational framework and database have been developed that provide these results as input to the WM PEIS for the calculation of human health risk impacts. The WM PEIS addresses management of five waste streams in the DOE complex: low-level waste (LLW), hazardous waste (HW), high-level waste (HLW), low-level mixed waste (LLMW), and transuranic waste (TRUW). Currently projected waste generation rates, storage inventories, and treatment process throughputs have been calculated for each of the waste streams. This report summarizes the accident analyses and aggregates the key results for each of the waste streams. Source terms are estimated, and results are presented for each of the major DOE sites and facilities by WM PEIS alternative for each waste stream. Key assumptions in the development of the source terms are identified. The appendices identify the potential atmospheric release of each toxic chemical or radionuclide for each accident scenario studied. They also discuss specific accident analysis data and guidance used or consulted in this report.

  18. Initial and Long-Term Results of Endovascular Therapy for Chronic Total Occlusion of the Subclavian Artery

    International Nuclear Information System (INIS)

    Babic, Srdjan; Sagic, Dragan; Radak, Djordje; Antonic, Zelimir; Otasevic, Petar; Kovacevic, Vladimir; Tanaskovic, Slobodan; Ruzicic, Dusan; Aleksic, Nikola; Vucurevic, Goran

    2012-01-01

    Purpose: To study the initial and long-term results of angioplasty and primary stenting for the treatment of chronic total occlusion (CTO) of the subclavian artery (SA). Materials and Methods: From January 1999 to February 2010, 56 patients (25 men with a mean age of 58 ± 8 years) underwent endovascular treatment for CTO of the SA. Duplex scans and arteriograms confirmed occlusion in all cases. Indications for recanalization were subclavian steal syndrome in 33 patients (58.1%), arm claudication in 13 patients (23.2%), and coronary ischemia in 7 patients (12.5%) who had a history of previous coronary artery bypass grafting that included left internal thoracic artery graft. Three patients (5.4%) were treated before the scheduled coronary artery bypass surgery, which included left internal thoracic artery graft. After successful recanalization, all arteries were stented, and all of the patients were followed-up at 1, 3, 6, and 12 months after surgery and annually thereafter. Results: Successful recanalization of the SA was achieved in 46 patients (82.1%), and the complication rate was 7.1%. During follow-up (mean 40 ± 26 months; range 2 to 125), the primary patency rates after 1 and 3 years were 97.9% and 82.7%, respectively. At the end of follow-up, 76% of the arteries showed no evidence of restenosis. Univariate analysis failed to identify any variable predictive of long-term patency of successfully recanalized SA. Conclusion: Percutaneous transluminal angioplasty with stenting of the complete total occlusion of the SA is a safe and effective procedure associated with low risks and good long-term results.

  19. Source apportionment of airborne particulates through receptor modeling: Indian scenario

    Science.gov (United States)

    Banerjee, Tirthankar; Murari, Vishnu; Kumar, Manish; Raju, M. P.

    2015-10-01

    Airborne particulate chemistry mostly governed by associated sources and apportionment of specific sources is extremely essential to delineate explicit control strategies. The present submission initially deals with the publications (1980s-2010s) of Indian origin which report regional heterogeneities of particulate concentrations with reference to associated species. Such meta-analyses clearly indicate the presence of reservoir of both primary and secondary aerosols in different geographical regions. Further, identification of specific signatory molecules for individual source category was also evaluated in terms of their scientific merit and repeatability. Source signatures mostly resemble international profile while, in selected cases lack appropriateness. In India, source apportionment (SA) of airborne particulates was initiated way back in 1985 through factor analysis, however, principal component analysis (PCA) shares a major proportion of applications (34%) followed by enrichment factor (EF, 27%), chemical mass balance (CMB, 15%) and positive matrix factorization (PMF, 9%). Mainstream SA analyses identify earth crust and road dust resuspensions (traced by Al, Ca, Fe, Na and Mg) as a principal source (6-73%) followed by vehicular emissions (traced by Fe, Cu, Pb, Cr, Ni, Mn, Ba and Zn; 5-65%), industrial emissions (traced by Co, Cr, Zn, V, Ni, Mn, Cd; 0-60%), fuel combustion (traced by K, NH4+, SO4-, As, Te, S, Mn; 4-42%), marine aerosols (traced by Na, Mg, K; 0-15%) and biomass/refuse burning (traced by Cd, V, K, Cr, As, TC, Na, K, NH4+, NO3-, OC; 1-42%). In most of the cases, temporal variations of individual source contribution for a specific geographic region exhibit radical heterogeneity possibly due to unscientific orientation of individual tracers for specific source and well exaggerated by methodological weakness, inappropriate sample size, implications of secondary aerosols and inadequate emission inventories. Conclusively, a number of challenging

  20. EXPERIENCES FROM THE SOURCE-TERM ANALYSIS OF A LOW AND INTERMEDIATE LEVEL RADWASTE DISPOSAL FACILITY

    International Nuclear Information System (INIS)

    Park, Jin Beak; Park, Joo-Wan; Lee, Eun-Young; Kim, Chang-Lak

    2003-01-01

    Enhancement of a computer code SAGE for evaluation of the Korean concept for a LILW waste disposal facility is discussed. Several features of source term analysis are embedded into SAGE to analyze: (1) effects of degradation mode of an engineered barrier, (2) effects of dispersion phenomena in the unsaturated zone and (3) effects of time dependent sorption coefficient in the unsaturated zone. IAEA's Vault Safety Case (VSC) approach is used to demonstrate the ability of this assessment code. Results of MASCOT are used for comparison purposes. These enhancements of the safety assessment code, SAGE, can contribute to realistic evaluation of the Korean concept of the LILW disposal project in the near future