A chemical and thermodynamic model of oil generation in hydrocarbon source rocks

Science.gov (United States)

Helgeson, Harold C.; Richard, Laurent; McKenzie, William F.; Norton, Denis L.; Schmitt, Alexandra

2009-02-01

Thermodynamic calculations and Gibbs free energy minimization computer experiments strongly support the hypothesis that kerogen maturation and oil generation are inevitable consequences of oxidation/reduction disproportionation reactions caused by prograde metamorphism of hydrocarbon source rocks with increasing depth of burial.These experiments indicate that oxygen and hydrogen are conserved in the process.Accordingly, if water is stable and present in the source rock at temperatures ≳25 but ≲100 °C along a typical US Gulf Coast geotherm, immature (reduced) kerogen with a given atomic hydrogen to carbon ratio (H/C) melts incongruently with increasing temperature and depth of burial to produce a metastable equilibrium phase assemblage consisting of naphthenic/biomarker-rich crude oil, a type-II/III kerogen with an atomic hydrogen/carbon ratio (H/C) of ˜1, and water. Hence, this incongruent melting process promotes diagenetic reaction of detritus in the source rock to form authigenic mineral assemblages.However, in the water-absent region of the system CHO (which is extensive), any water initially present or subsequently entering the source rock is consumed by reaction with the most mature kerogen with the lowest H/C it encounters to form CO 2 gas and a new kerogen with higher H/C and O/C, both of which are in metastable equilibrium with one another.This hydrolytic disproportionation process progressively increases both the concentration of the solute in the aqueous phase, and the oil generation potential of the source rock; i.e., the new kerogen can then produce more crude oil.Petroleum is generated with increasing temperature and depth of burial of hydrocarbon source rocks in which water is not stable in the system CHO by a series of irreversible disproportionation reactions in which kerogens with higher (H/C)s melt incongruently to produce metastable equilibrium assemblages consisting of crude oil, CO 2 gas, and a more mature (oxidized) kerogen with a lower

Applicability of initial stress measurement methods to Horonobe Siliceous rocks and initial stress state around Horonobe Underground Research Laboratory

International Nuclear Information System (INIS)

Sanada, Hiroyuki; Niunoya, Sumio; Matsui, Hiroya; Fujii, Yoshiaki

2009-01-01

Understanding initial stress condition in deep underground is important for such construction as rock cavern for geological disposal of HLW and underground power plant. Neogene sedimentary rock is widely distributed in Japan. There are only a few studies of initial stress measurement in Neogene sedimentary rock mass in Japan due to difficulty of measurement. Evaluation of initial stress condition around Horonobe Underground Research Laboratory Project was carried out in order to understand initial stress condition and applicability of AE, DSCA and hydraulic fracturing (HF) methods to Neogene sedimentary rock. Initial stress values obtained from AE method is smaller than overburden pressure due to time dependency of Kaizer effect. It would be difficult to use AE method as initial stress measurement method for Horonobe Siliceous rocks. Principal stress values by DSCA are similar to those by HF tests. Directions of maximum horizontal principal stresses are approximately in E-W and corresponded to HF results. In HF, rod type and wire-line type systems were compared. Workability of rod type was much better than wire-line type. However, re-opening pressure were not able to be precisely measured in case of rod type system due to the large compliance of the packers and rods. Horizontal maximum and minimum principal stresses increase linearly in HF results. Deviatoric stress is acting at shallow depth. Initial stress condition approaches hydrostatic condition with depth. Direction of maximum horizontal principal stress was in E-W direction which was similar to tectonic movement around Horonobe URL by triangular surveying. (author)

Depositional environment and source rock potential of Cenomanian and Turonian sedimentary rocks of the Tarfaya Basin, Southwest Morocco

Energy Technology Data Exchange (ETDEWEB)

Ghassal, B.I.; Littke, R.; Sachse, V.; Sindern, S.; Schwarzbauer, J.

2016-07-01

Detailed organic and inorganic geochemical analyses were used to assess the depositional environment and source rock potential of the Cenomanian and Turonian oil shale deposits in the Tarfaya Basin. This study is based on core samples from the Tarfaya Sondage-4 well that penetrated over 300m of Mid Cretaceous organic matter-rich deposits. A total of 242 samples were analyzed for total organic and inorganic carbon and selected samples for total sulfur and major elements as well as for organic petrology, Rock-Eval pyrolysis, Curie-Point-pyrolysis-gaschromatography-Mass-Spectrometry and molecular geochemistry of solvent extracts. Based on major elements the lower Cenomanian differs from the other intervals by higher silicate and lower carbonate contents. Moreover, the molecular geochemistry suggests anoxic bottom marine water conditions during the Cenomanian-Turonian Boundary Event (CTBE; Oceanic Anoxic Event 2: OAE2). As a proxy for the Sorg/Corg ratio, the ratio total thiophenes/total benzenes compounds was calculated from pyrolysate compositions. The results suggest that Sorg/ Corg is low in the lower Cenomanian, moderate in the upper Cenomanian, very high in the CTBE (CenomanianTuronian Boundary Event) and high in the Turonian samples. Rock-Eval data reveal that the lower Cenomanian is a moderately organic carbon-rich source rock with good potential to generate oil and gas upon thermal maturation. On the other hand, the samples from the upper Cenomanian to Turonian exhibit higher organic carbon content and can be classified as oil-prone source rocks. Based on Tmax data, all rocks are thermally immature. The microscopic investigations suggest dominance of submicroscopic organic matter in all samples and different contents of bituminite and alginite. The lower Cenomanian samples have little visible organic matter and no bituminite. The upper Cenomanian and CTBE samples are poor in bituminite and have rare visible organic matter, whereas the Turonian samples change

Strength Assessment of Broken Rock Postgrouting Reinforcement Based on Initial Broken Rock Quality and Grouting Quality

Directory of Open Access Journals (Sweden)

Hongfa Xu

2017-01-01

Full Text Available To estimate postgrouting rock mass strength growth is important for engineering design. In this paper, using self-developed indoor pressure-grouting devices, 19 groups of test cubic blocks were made of the different water cement ratio grouting into the broken rock of three kinds of particle sizes. The shear strength parameters of each group under different conditions were tested. Then this paper presents a quantitative calculation method for predicting the strength growth of grouted broken rock. Relational equations were developed to investigate the relationship between the growth rates of uniaxial compressive strength (UCS, absolute value of uniaxial tensile strength (AUTS, internal friction angle, and cohesion for post- to pregrouting broken rock based on Mohr-Coulomb strength criterion. From previous test data, the empirical equation between the growth rate of UCS and the ratio of the initial rock mass UCS to the grout concretion UCS has been determined. The equations of the growth rates of the internal friction coefficient and UCS for grouting broken rock with rock mass rating (RMR and its increment have been established. The calculated results are consistent with the experimental results. These observations are important for engineered design of grouting reinforcement for broken rock mass.

Lead isotopes in archaean plutonic rocks

International Nuclear Information System (INIS)

Oversby, V.M.

1978-01-01

Archaean intrusive rocks have initial Pb isotopic compositions which show a varied and complex history for the source regions of the rocks. Even the oldest rocks from Greenland indicate heterogenous U and Pb distribution prior to 3800 m.y. ago. Source regions with μ values less than 7 must have played a significant role in the early history of the earth. By late Archaean time U/Pb ratios of source regions had increased substantially. Data from Australia and North America show distinct regional differences, both within and between continents. (Auth.)

The potentiality of hydrocarbon generation of the Jurassic source rocks in Salam-3x well,

Directory of Open Access Journals (Sweden)

Mohamed M. El Nady

2016-03-01

Full Text Available The present work deals with the identification of the potential and generating capability of oil generation in the Jurassic source rocks in the Salam-3x well. This depending on the organo-geochemical analyses of cutting samples representative of Masajid, Khatatba and Ras Qattara formations, as well as, representative extract samples of the Khatatba and Ras Qattara formations. The geochemical analysis suggested the potential source intervals within the encountered rock units as follows: Masajid Formation bears mature source rocks and have poor to fair generating capability for generating gas (type III kerogen. Khatatba Formation bears mature source rock, and has poor to good generating capability for both oil and gas. Ras Qattara Formation constituting mature source rock has good to very good generating capability for both oil and gas. The burial history modeling shows that the Masajid Formation lies within oil and gas windows; Khatatba and Ras Qattara formations lie within the gas window. From the biomarker characteristics of source rocks it appears that the extract is genetically related as the majority of them were derived from marine organic matters sources (mainly algae deposited under reducing environment and take the direction of increasing maturity and far away from the direction of biodegradation. Therefore, Masajid Formation is considered as effective source rocks for generating hydrocarbons, while Khatatba and Ras Qattara formations are the main source rocks for hydrocarbon accumulations in the Salam-3x well.

Geochemistry of Eagle Ford group source rocks and oils from the first shot field area, Texas

Science.gov (United States)

Edman, Janell D.; Pitman, Janet K.; Hammes, Ursula

2010-01-01

Total organic carbon, Rock-Eval pyrolysis, and vitrinite reflectance analyses performed on Eagle Ford Group core and cuttings samples from the First Shot field area, Texas demonstrate these samples have sufficient quantity, quality, and maturity of organic matter to have generated oil. Furthermore, gas chromatography and biomarker analyses performed on Eagle Ford Group oils and source rock extracts as well as weight percent sulfur analyses on the oils indicate the source rock facies for most of the oils are fairly similar. Specifically, these source rock facies vary in lithology from shales to marls, contain elevated levels of sulfur, and were deposited in a marine environment under anoxic conditions. It is these First Shot Eagle Ford source facies that have generated the oils in the First Shot Field. However, in contrast to the generally similar source rock facies and organic matter, maturity varies from early oil window to late oil window in the study area, and these maturity variations have a pronounced effect on both the source rock and oil characteristics. Finally, most of the oils appear to have been generated locally and have not experienced long distance migration. 

Characterizing the hypersiliceous rocks of Belgium used in (pre-)history: a case study on sourcing sedimentary quartzites

International Nuclear Information System (INIS)

Veldeman, Isis; Baele, Jean-Marc; De Doncker, H W J A; Goemaere, Eric; Deceukelaire, Marleen; Dusar, Michiel

2012-01-01

Tracking raw material back to its extraction source is a crucial step for archaeologists when trying to deduce migration patterns and trade contacts in (pre-)history. Regarding stone artefacts, the main rock types encountered in the archaeological record of Belgium are hypersiliceous rocks. This is a newly introduced category of rock types comprising those rocks made of at least 90% silica. These are strongly silicified quartz sands or sedimentary quartzites, siliceous rocks of chemical and biochemical origin (e.g. flint), very pure metamorphic quartzites and siliceous volcanic rocks (e.g. obsidian). To be able to distinguish between different extraction sources, ongoing research was started to locate possible extraction sources of hypersiliceous rocks and to characterize rocks collected from these sources. Characterization of these hypersiliceous rocks is executed with the aid of optical polarizing microscopy, optical cold cathodoluminescence and scanning-electron microscopy combined with energy-dispersive x-ray spectrometry and with back-scatter electron imaging. In this paper, we focus on various sedimentary quartzites of Paleogene stratigraphical level. (paper)

Hydrocarbon Source Rock Potential of the Sinamar Formation, Muara Bungo, Jambi

Directory of Open Access Journals (Sweden)

Moh. Heri Hermiyanto Zajuli

2014-07-01

Full Text Available DOI: 10.17014/ijog.v1i1.175The Oligocene Sinamar Formation consists of shale, claystone, mudstone, sandstone, conglomeratic sandstone, and intercalation of coal seams. The objective of study was to identify the hydrocarbon source rock potential of the Sinamar Formation based on geochemichal characteristics. The analyses were focused on fine sediments of the Sinamar Formation comprising shale, claystone, and mudstone. Primary data collected from the Sinamar Formation well and outcrops were analyzed according to TOC, pyrolisis analysis, and gas chromatography - mass spectometry of normal alkanes that include isoprenoids and sterane. The TOC value indicates a very well category. Based on TOC versus Pyrolysis Yields (PY diagram, the shales of Sinamar Formation are included into oil prone source rock potential with good to excellent categories. Fine sediments of the Sinamar Formation tend to produce oil and gas originated from kerogen types I and III. The shales tend to generate oil than claystone and mudstone and therefore they are included into a potential source rock. 

Trace element characterisation of Cretaceous Orange Basin hydrocarbon source rocks

International Nuclear Information System (INIS)

Akinlua, A.; Adekola, S.A.; Swakamisa, O.; Fadipe, O.A.; Akinyemi, S.A.

2010-01-01

Research highlights: → Vanadium and nickel contents indicate that the rock samples from the Orange Basin have marine organic matter input. → The organic matter of the Orange Basin source rocks were deposited in reducing conditions. → Despite the similarities in the organic matter source input and depositional environment of the samples from the two well, cross plots of Co/Ni versus V/Ni and Mo/Ni versus Co/Ni were able to reveal their subtle differences. → Cluster analysis classified the samples into three groups based on subtle differences in their .thermal maturity. - Abstract: Trace elements in the kerogen fraction of hydrocarbon source rock samples from two wells obtained from the Cretaceous units of the Orange Basin, South Africa were determined using X-ray fluorescence spectrometry, in order to determine their distribution and geochemical significances. The concentrations of the elements (As, Ce, Co, Cu, Fe, Mo, Ni, Pb and V) determined ranged from 0.64 to 47,300 ppm for the samples analysed. The total organic carbon (TOC) values indicate that the samples are organic rich but did not show any trend with the distribution of the trace metals except Ce, Mo and Pb. Dendrogram cluster analysis discriminated the samples into three groups on the basis of their level of thermal maturity. Thermal maturity has a significant effect on the distribution of the trace metals. Cobalt/Ni and V/Ni ratios and cross plots of the absolute values of V and Ni indicate that the samples had significant marine organic matter input. The V and Ni contents and V/(V + Ni) ratio indicate that the organic matter of the source rocks had been deposited in reducing conditions. Despite the similarities in the organic matter source input and depositional environment of the organic matter of the samples from the two well, cross plots of Co/Ni versus V/Ni and Mo/Ni versus Co/Ni were able to reveal subtle differences. Cluster analysis of the samples was also able to reveal the subtle

Fracture Initiation of an Inhomogeneous Shale Rock under a Pressurized Supercritical CO2 Jet

Directory of Open Access Journals (Sweden)

Yi Hu

2017-10-01

Full Text Available Due to the advantages of good fracture performance and the application of carbon capture and storage (CCS, supercritical carbon dioxide (SC-CO2 is considered a promising alternative for hydraulic fracturing. However, the fracture initiation mechanism and its propagation under pressurized SC-CO2 jet are still unknown. To address these problems, a fluid–structure interaction (FSI-based numerical simulation model along with a user-defined code was used to investigate the fracture initiation in an inhomogeneous shale rock. The mechanism of fracturing under the effect of SC-CO2 jet was explored, and the effects of various influencing factors were analyzed and discussed. The results indicated that higher velocity jets of SC-CO2 not only caused hydraulic-fracturing ring, but also resulted in the increase of stress in the shale rock. It was found that, with the increase of perforation pressure, more cracks initiated at the tip. In contrast, the length of cracks at the root decreased. The length-to-diameter ratio and the aperture ratio distinctly affected the pressurization of SC-CO2 jet, and contributed to the non-linear distribution and various maximum values of the stress in shale rock. The results proved that Weibull probability distribution was appropriate for analysis of the fracture initiation. The studied parameters explain the distribution of weak elements, and they affect the stress field in shale rock.

Depositional environments and oil potential of Jurassic/Cretaceous source rocks within the Seychelles microcontinent

Energy Technology Data Exchange (ETDEWEB)

Plummer, P.S.; Joseph, P.R.; Samson, P.J. [Seychelles National Oil Co., Mahe (Seychelles)

1998-12-31

The Seychelles microcontinent became isolated between the Somali, Mascarene and Arabian basins of the Indian Ocean as a result of the Mesozoic fragmentation of Gondwana. Major rifting events occurred during the Triassic-Middle Jurassic and Late Cretaceous (Cenomanian-Santonian and Maastrichtian) during which shaly source rock facies accumulated in principally marginal marine/deltaic environments. Between these times, post-rift passive margin deposition within restricted to open marine environments produced shaly source rocks during late Middle Jurasic-Early Cretaceous, Campanian-Maastrichtian and Paleocene times. Recent geochemical analysis of cuttings from the Seagull Shoals-1 well has identified an oil-prone liptinitic (Type II) coaly shale within early Middle Jurassic abandoned deltaic deposits. This coaly source rock is regionally developed, having also been identified in the Majunja and Morondava basins of Madagascar. Oil-prone Type II organic matter has also been identified in the Owen Bank A-1 well within restricted marine shales of late Middle Jurassic age. These shales are part of a thick post-rift source rock sequence that extends into the Early Cretaceous and is in part correlative with the proven Late Jurassic Uarandab Shale of Somalia. Analysis of Campanian marine shales from Reith Bank-1 well identified significant dilution of total organic carbon content in composite, compared to picked, well cuttings samples. This finding supports a published inference that these post-rift shales have source rock potential. (author)

Hydrocarbon source rock potential evaluation of the Late Paleocene ...

Indian Academy of Sciences (India)

63

research is available on its source rock potential evaluation at Nammal Gorge Section in the Salt. Range, Potwar Basin .... methods of Tucker (2003) and Assaad (2008) have been followed. A total of fifteen ..... Business Media. Baker D M, Lillie ...

Comparison of Crack Initiation, Propagation and Coalescence Behavior of Concrete and Rock Materials

Science.gov (United States)

Zengin, Enes; Abiddin Erguler, Zeynal

2017-04-01

There are many previously studies carried out to identify crack initiation, propagation and coalescence behavior of different type of rocks. Most of these studies aimed to understand and predict the probable instabilities on different engineering structures such as mining galleries or tunnels. For this purpose, in these studies relatively smaller natural rock and synthetic rock-like models were prepared and then the required laboratory tests were performed to obtain their strength parameters. By using results provided from these models, researchers predicted the rock mass behavior under different conditions. However, in the most of these studies, rock materials and models were considered as contains none or very few discontinuities and structural flaws. It is well known that rock masses naturally are extremely complex with respect to their discontinuities conditions and thus it is sometimes very difficult to understand and model their physical and mechanical behavior. In addition, some vuggy rock materials such as basalts and limestones also contain voids and gaps having various geometric properties. Providing that the failure behavior of these type of rocks controlled by the crack initiation, propagation and coalescence formed from their natural voids and gaps, the effect of these voids and gaps over failure behavior of rocks should be investigated. Intact rocks are generally preferred due to relatively easy side of their homogeneous characteristics in numerical modelling phases. However, it is very hard to extract intact samples from vuggy rocks because of their complex pore sizes and distributions. In this study, the feasibility of concrete samples to model and mimic the failure behavior vuggy rocks was investigated. For this purpose, concrete samples were prepared at a mixture of %65 cement dust and %35 water and their physical and mechanical properties were determined by laboratory experiments. The obtained physical and mechanical properties were used to

The strata and palaeo-geomorphology framework at the end of neoproterozoic and development mode of source rocks at the beginning of Cambrian in Tarim Basin, China

Directory of Open Access Journals (Sweden)

Xin Yang

2017-12-01

Full Text Available Referred to the new recognition from petroleum exploration of the Sinian to Cambrian in South China, it could be considered that the distribution of the early Cambrian source rocks was controlled by the palaeo-geomorphology at the end of Neoproterozoic in the Tarim Basin. Based on the zircon U-Pb dating of pyroclastic rock samples from the clastic rock stratum under the bottom of Cambrian carbonate rocks, the stratigraphic correlation of the Sinian to Cambrian was conducted to build the palaeo-geomorphology framework at the end of Neoproterozoic in Tarim Basin. Lastly, according to the development mode of source rocks at the beginning of Cambrian, the distribution of source rocks was predicted initially through the division of seismic facies. The youngest zircon concordia age of pyroclastic rocks from the bottom of well Tong 1 is 707±8Ma. It was revealed by the strata framework of the Sinian to Cambrian, the palaeo-geomorphology at the end of Neoproterozoic in Tarim Basin was characterized by an uplift highland in Bachu-Tazhong area, the south north high-low, and the west is higher than the east. The distribution of source rocks in the bottom of the Cambrian on the palaeo-platform and slopes was coincident with the Upper Sinian dolomite basically. But the contemporaneous sediment happened to be absent or changed in sedimentary facies on the uplift and its edges. From the seismic facies of the strata under the bottom of Cambrian, it could be concluded that source rocks in the type of the Xishanbraque Group (∈1xs was limited in the Manjiaer Depression, while the source rocks in the type of the Yuertusi Group (∈1y are widely distributed in south of Tabei Uplift, east Awat Depression, and even the Maigt Slope. However, among the west Awat Depression and western Tanguzibasi Depression, and the middle area of the Bachu-Tazhong Uplifts, the contemporaneous source rocks may have changed into sedimentary facies of tidal flat and lagoon, instead of

On the source material of magmas - with special reference to Nd isotopic ratios of igneous rocks

International Nuclear Information System (INIS)

Shuto, Kenji

1980-01-01

In 1973, the Sm-Nd method was first used for the measurement of the absolute age of igneous rocks and meteorites. Subsequently in the following years, the research works by means of the Nd isotopic ratio in igneous rocks have been made strenuously in order to reveal the chemistry of the source materials of magma giving rise to the igneous rocks and further the evolution process of mantle and earth's crust. The fundamental items for the Sm-Nd method are explained. Then, the research results more important in the above connection are given. Finally, the ideas by the author concerning the source materials of magma are presented from the data available on the Nd isotopes in meteorites and igneous rocks. The following matters are described: the fundamentals of Sm-Nd method, the Nd content in seawater, the negative correlation between Nd and Sr isotopic ratios in igneous rocks, magma source materials and Nd isotopes, and considerations on magma source materials. (J.P.N.)

Organic compositions of lacustrine source rocks in Jiyang super-depression and its implication to petroleum geology

Institute of Scientific and Technical Information of China (English)

无

2006-01-01

The compositions of organic matter in four immature source rocks from Tertiary strata of Jiyang super-depression, the most typical continental rift subsidence basin in East China, have been studied by different extracting methods with CHCl3, MAC and CS2/NMP, respectively. The results suggest that there are great differences among the chemical compositions of organic matter in the source rocks derived from different depositional environments. About 79% of all the organic matter exists by non- covalent bond in the Es4 source rocks which were deposited under the saline lacustrine, indicating that its organic matter is not the real kerogen, but mainly composed of soluble organic matter which is easy to generate hydrocarbon at lower temperature. This is why the immature oils were derived from Es4 source rocks in Dongying depression. In contrast, around 60% of organic matter exists by covalent bond in Es3 source rocks which were deposited under the deep brackish-fresh lacustrine, showing that Es3 source rocks are mainly composed of kerogen producing mature hydrocarbon at higher temperature. The thermal simulation experiments, upon the remaining solid source rocks which were sequentially extracted by the three solvents, have been carried out. The chloroform extracts from the simulation product have been compared with the other three solvent extracts gained at room temperature. It is obvious that remarkable odd/even predominance (OEP) is mainly the characteristic of soluble organic matter; phytane mostly exists in the soluble organic matter by means of non-covalent bonds and characteristics of soluble organic matter are similar to these in immature oils produced in Jiyang super-depression.

Dating and source determination of volcanic rocks from Khunik area (South of Birjand, South Khorasan using Rb-Sr and Sm-Nd isotopes

Directory of Open Access Journals (Sweden)

Somayeh Samiee

2016-12-01

Full Text Available The Khunik area is located in the south of Birjand, Khorasan province, in the eastern margin of Lut block. Tertiary volcanic rocks have andesite to trachy-andesite composition. Dating analyzing by Rb-Sr method on plagioclase and hornblende as well as whole-rock isochron method was performed on pyroxene-hornblende andesite rock unit. On this basis the emplacement age is Upper Paleocene (58±11 Ma. These rocks have initial 87Sr/86Sr and εNd 0.7046-0.7049 and 2.16-3.12, respectively. According to isotopic data, volcanic rocks originated from depleted mantle and have the least crust contamination while it was fractionated. Geochemically, Khunik volcanic rocks have features typical of calk-alkaline to shoshonite and are metaluminous. Enrichment in LILEs and typical negative anomalies of Nb and Ti are evidences that the volcanic rocks formed in a subduction zone and active continental margin. Modeling suggests that these rocks were derived dominantly from 1–5% partial melting of a mainly spinel garnet lherzolite mantle source that is metasomatized by slab-derived fluid.

Applying Bioaugmentation to Treat DNAPL Sources in Fractured Rock

Science.gov (United States)

2017-03-27

Figure 1. This ESTCP demonstration was focused in the vicinity of Building 8595, adjacent to the location of a reported surface release of PCE ( Earth ...electron donor source, such as vegetable oil, is typically used in passive approaches. When treating a DNAPL source area in fractured rock, there are... vegetable oil) are used. Hydrogen The generation of hydrogen can be used to verify fermentation of electron donor. Metals (Fe, Mn, As) Increase

Source rock potential of the organic rich Turonian - Upper Campanian carbonates of northern Lebanon

Energy Technology Data Exchange (ETDEWEB)

Daher, S. Bou; Littke, R. [RWTH Aachen Univ. (Germany). Energy and Mineral Resources Group (EMR); Nader, F.H. [IFP Energies nouvelles, Paris (France). Dept. of Sedimentology-Stratigraphy

2013-08-01

Upper Cretaceous chalks, marls, and shales are arguably the most prolific petroleum source rocks in the eastern Mediterranean region. 209 core samples from the Turonian - Upper Campanian rock succession in north Lebanon were collected and analyzed for their organic matter (OM) content, quality, and maturity. The total organic carbon (TOC) measurements revealed a very good source rock potential for a 150 m interval within the Upper Santonian - Upper Campanian, with an average of 2% TOC. High HI values (average 707 mg/g TOC) characterize these source rocks as type I kerogen and reflect a very good preservation of the organic matter. T{sub max} values (average 421 C) match the other maturity parameters such as vitrinite reflectance (average 0.35%), and all point towards immature organic matter. The equivalent Upper Cretaceous in the offshore Levant basin has enough overburden to have reached maturity. However, the accurate extrapolation of the organic matter quality and quantity to the offshore is yet a challenge with the data at hand. (orig.)

Restoration of Circum-Arctic Upper Jurassic source rock paleolatitude based on crude oil geochemistry

Science.gov (United States)

Peters, K.E.; Ramos, L.S.; Zumberge, J.E.; Valin, Z.C.; Scotese, C.R.

2008-01-01

Tectonic geochemical paleolatitude (TGP) models were developed to predict the paleolatitude of petroleum source rock from the geochemical composition of crude oil. The results validate studies designed to reconstruct ancient source rock depositional environments using oil chemistry and tectonic reconstruction of paleogeography from coordinates of the present day collection site. TGP models can also be used to corroborate tectonic paleolatitude in cases where the predicted paleogeography conflicts with the depositional setting predicted by the oil chemistry, or to predict paleolatitude when the present day collection locality is far removed from the source rock, as might occur due to long distance subsurface migration or transport of tarballs by ocean currents. Biomarker and stable carbon isotope ratios were measured for 496 crude oil samples inferred to originate from Upper Jurassic source rock in West Siberia, the North Sea and offshore Labrador. First, a unique, multi-tiered chemometric (multivariate statistics) decision tree was used to classify these samples into seven oil families and infer the type of organic matter, lithology and depositional environment of each organofacies of source rock [Peters, K.E., Ramos, L.S., Zumberge, J.E., Valin, Z.C., Scotese, C.R., Gautier, D.L., 2007. Circum-Arctic petroleum systems identified using decision-tree chemometrics. American Association of Petroleum Geologists Bulletin 91, 877-913]. Second, present day geographic locations for each sample were used to restore the tectonic paleolatitude of the source rock during Late Jurassic time (???150 Ma). Third, partial least squares regression (PLSR) was used to construct linear TGP models that relate tectonic and geochemical paleolatitude, where the latter is based on 19 source-related biomarker and isotope ratios for each oil family. The TGP models were calibrated using 70% of the samples in each family and the remaining 30% of samples were used for model validation. Positive

Microwave-assisted nonionic surfactant extraction of aliphatic hydrocarbons from petroleum source rock

Energy Technology Data Exchange (ETDEWEB)

Akinlua, A., E-mail: geochemresearch@yahoo.com [Fossil Fuels and Environmental Geochemistry Group, Department of Chemistry, Obafemi Awolowo University, Ile-Ife (Nigeria); Jochmann, M.A.; Laaks, J.; Ewert, A.; Schmidt, T.C. [Instrumental Analytical Chemistry, University Duisburg-Essen, Universitaetsstr, 5, 45141 Essen (Germany)

2011-04-08

The extraction of aliphatic hydrocarbons from petroleum source rock using nonionic surfactants with the assistance of microwave was investigated and the conditions for maximum yield were determined. The results showed that the extraction temperatures and kinetic rates have significant effects on extraction yields of aliphatic hydrocarbons. The optimum temperature for microwave-assisted nonionic surfactant extraction of aliphatic hydrocarbons from petroleum source rock was 105 deg. C. The optimum extraction time for the aliphatic hydrocarbons was at 50 min. Concentration of the nonionic surfactant solution and irradiation power had significant effect on the yields of aliphatic hydrocarbons. The yields of the analytes were much higher using microwave assisted nonionic surfactant extraction than with Soxhlet extraction. The recoveries of the n-alkanes and acyclic isoprenoid hydrocarbons for GC-MS analysis from the extractant nonionic surfactant solution by in-tube extraction (ITEX 2) with a TENAX TA adsorbent were found to be efficient. The results show that microwave-assisted nonionic surfactant extraction (MANSE) is a good and efficient green analytical preparatory technique for geochemical evaluation of petroleum source rock.

Microwave-assisted nonionic surfactant extraction of aliphatic hydrocarbons from petroleum source rock

International Nuclear Information System (INIS)

Akinlua, A.; Jochmann, M.A.; Laaks, J.; Ewert, A.; Schmidt, T.C.

2011-01-01

The extraction of aliphatic hydrocarbons from petroleum source rock using nonionic surfactants with the assistance of microwave was investigated and the conditions for maximum yield were determined. The results showed that the extraction temperatures and kinetic rates have significant effects on extraction yields of aliphatic hydrocarbons. The optimum temperature for microwave-assisted nonionic surfactant extraction of aliphatic hydrocarbons from petroleum source rock was 105 deg. C. The optimum extraction time for the aliphatic hydrocarbons was at 50 min. Concentration of the nonionic surfactant solution and irradiation power had significant effect on the yields of aliphatic hydrocarbons. The yields of the analytes were much higher using microwave assisted nonionic surfactant extraction than with Soxhlet extraction. The recoveries of the n-alkanes and acyclic isoprenoid hydrocarbons for GC-MS analysis from the extractant nonionic surfactant solution by in-tube extraction (ITEX 2) with a TENAX TA adsorbent were found to be efficient. The results show that microwave-assisted nonionic surfactant extraction (MANSE) is a good and efficient green analytical preparatory technique for geochemical evaluation of petroleum source rock.

Relationship between fluvial clastic sediment and source rock abundance in Rapti river basin of central Nepal Himalayas

International Nuclear Information System (INIS)

Tamrakar Naresh Kazi; Shresth Madhusudan Bhakta

2008-01-01

Many tributaries from carbonate sedimentary, metamorphic and igneous rocks of the Lesser Himalayan and clastic sedimentary rocks of the Sub-Himalayan Ranges carry gravelly sediments to the Rapti River. River bar sediments were analyzed for composition and texture to evaluate downstream changes in properties, and to establish relationship between proportion of clasts and the abundance of rock types in the source areas. Percent quartzite clast or granite clast increases whereas that of carbonate, schist or slate decreases along downstream. The largest grain size decreases downstream, whereas fatness index and sphericity tend to increase. Despite of little diminish in relative abundance of rock types in source areas along the river, the relative proportion of corresponding clast type shows rapid reduction (e.g. slate or phyllite or carbonate clasts) or rapid enhancement (e.g. granite clast). The relationships of quartzite clast and schist clasts with their corresponding source rocks are statistically significant suggesting that these clasts can provide clue to source rock abundance. About 85 to 94% of the gravel clasts represent rock types of the Lesser Himalayan Range suggesting that this range has been contributing enormous amount of sediments.

Initial growth of maize in response to application of rock phosphate, vermicompost and endophytic bacteria

Directory of Open Access Journals (Sweden)

Lílian Estrela Borges Baldotto

2012-04-01

Full Text Available Due to the high energy requirement and demand for non-renewable resources for the production of chemical fertilizers, added also to the environmental impact caused by the use of such products, it is important to intensify research on bio-based agricultural inputs. The use of nitrogen-fixing endophytic and phosphate solubilizing bacteria can provide these nutrients to the plants from the air and poorly soluble phosphorus sources, such as phosphate rock. The objective of this study was to evaluate the nutrition and initial growth of maize (Zea mays L. in response to the inoculation of nitrogen-fixing and rock phosphate solubilizing endophytic bacteria, in single or mixed formulation, applied with vermicompost. The treatments containing bacteria, both diazotrophic and phosphate solubilizing, when compared to controls, showed higher levels of leaf nitrogen and phosphorus in maize, as well as higher growth characteristics. The application of vermicompost showed synergistic effect when combined with endophytic bacteria. Thus, the innovation of the combination of the studied factors may contribute to the early development of maize.

A simple source preparation method for alpha-ray spectrometry of volcanic rock sample

International Nuclear Information System (INIS)

Takahashi, Masaomi; Kurihara, Yuichi; Sato, Jun

2006-01-01

A simple source preparation method was developed for the alpha-ray spectrometry to determine U and Th in volcanic rockes. Isolation of U and Th from volcanic rocks was made by use of UTEVA-Spec. resin, extraction chromatograph material. U and Th were extracted by TTA-benzene solution and organic phase was evaporated drop by drop on a hot stainless steel planchet to dryness. This method was found to be effective for the preparation of sources for alpha-ray spectrometry. (author)

Distribution of organic carbon and petroleum source rock potential of Cretaceous and lower Tertiary carbonates, South Florida Basin: preliminary results

Science.gov (United States)

Palacas, James George

1978-01-01

Analyses of 134 core samples from the South Florida Basin show that the carbonates of Comanchean age are relatively richer in average organic carbon (0.41 percent) than those of Coahuilan age (0.28 percent), Gulfian age (0.18 percent) and Paleocene age (0.20 percent). They are also nearly twice as rich as the average world, wide carbonate (average 0.24 percent). The majority of carbonates have organic carbons less than 0.30 percent but the presence of many relatively organic rich beds composed of highly bituminous, argillaceous, highly stylolitic, and algal-bearing limestones and dolomites accounts for the higher percentage of organic carbon in some of the stratigraphic units. Carbonate rocks that contain greater than 0.4 percent organic carbon and that might be considered as possible petroleum sources were noted in almost each subdivision of the Coahuilan and Comanchean Series but particularly the units of Fredericksburg 'B', Trinity 'A', Trinity 'F', and Upper Sunniland. Possible source rocks have been ascribed by others to the Lower Sunniland, but lack of sufficient samples precluded any firm assessment in this initial report. In the shallower section of the basin, organic-rich carbonates containing as much as 3.2 percent organic carbon were observed in the lowermost part of the Gulfian Series and carbonate rocks with oil staining or 'dead' and 'live oil' were noted by others in the uppermost Gulfian and upper Cedar Keys Formation. It is questionable whether these shallower rocks are of sufficient thermal maturity to have generated commercial oil. The South Florida basin is still sparsely drilled and produces only from the Sunniland Limestone at an average depth of 11,500 feet (3500 m). Because the Sunniland contains good reservoir rocks and apparently adequate source rocks, and because the success rate of new oil field discoveries has increased in recent years, the chances of finding additional oil reserves in the Sunniland are promising. Furthermore, the

Assessing initial conditions for chloride transport across low-permeability argillaceous rocks, Wellenberg, Switzerland

International Nuclear Information System (INIS)

Waber, H.N.; Hobbs, M.Y.; Frape, S.K.

2013-01-01

Information about fluid evolution and solute transport in a low-permeability metamorphic rock sequence has been obtained by comparing chloride concentrations and chlorine isotope ratios of pore water, groundwater, and fluid inclusions. The similarity of δ 37 Cl values in fluid inclusions and groundwater suggests a closed-system evolution during the metamorphic overprint, and signatures established at this time appear to form the initial conditions for chloride transport after exhumation of the rock sequence. (authors)

Interpretation of Oil Seepage of Source Rock Based Magnetic Survey in Cipari Cilacap District

Directory of Open Access Journals (Sweden)

Sukmaji Anom Raharjo

2015-12-01

Full Text Available The magnetic survey had been conducted in Village of Cipari, District of Cipari, Region of  Cilacap to interpret to the location of the oil seepage source rock. Boundary of the research area is 108.75675°E – 108.77611°E and 7.42319°S – 7.43761°S. The observed total magnetic data is corrected and reducted to obtain the local magnetic anomaly data. The local magnetic anomaly data is applied to model the subsurface bodies anomalies based on the Mag2DC for Windows software. With be supported the geological information, the some bodies anomalies are interpreted as the basaltic igneous rock (c = 0.0051, the alternately of sandstone and claystone and insert of marl from Halang Formation (c = 0.0014, the breccia from Kumbang Formation (c = 0.0035, the alternately of sandstones and claystone with insert of marl and breccia from Halang Formation (c = 0.0036, the claystone from Tapak Formation (c = 0.0015, the alternately of sandstones and claystone with insert of marl and compacted breccia from Halang Formation (c = 0.0030, and the alternately of sandstone and claystone from   Halang Formation (c = 0.0020. The plantonic foraminifer fossils as resources of oil seepage are estimated in the sedimentaries rocks, where the oil flows from those rocks into the         reservoir (source rock. Based on the interpretation results, the source rock is above basaltic igneous rock with the approximate position is 108.76164°W and 7.43089°S; and the depth is 132.09 meters below the average topographic.

Assessing initial conditions for chloride transport across low-permeability argillaceous rocks, Wellenberg, Switzerland

Energy Technology Data Exchange (ETDEWEB)

Waber, H.N. [Rock-Water Interaction Group, Institute of Geological Sciences, University of Bern, Baltzerstrasse 1-3, 3012 Bern (Switzerland); Hobbs, M.Y. [Rock-Water Interaction Group, Institute of Geological Sciences, University of Bern, Baltzerstrasse 1-3, 3012 Bern (Switzerland); Nuclear Waste Management Organization (NWMO), 22 St. Clair Avenue East, M4T 2S3 Toronto, Ontario (Canada); Frape, S.K. [Department of Earth and Environmental Sciences, University of Waterloo, Waterloo, Ontario (Canada)

2013-07-01

Information about fluid evolution and solute transport in a low-permeability metamorphic rock sequence has been obtained by comparing chloride concentrations and chlorine isotope ratios of pore water, groundwater, and fluid inclusions. The similarity of δ{sup 37}Cl values in fluid inclusions and groundwater suggests a closed-system evolution during the metamorphic overprint, and signatures established at this time appear to form the initial conditions for chloride transport after exhumation of the rock sequence. (authors)

Lower Cretaceous Source Rock and its Implication for the Gulf of Guinea Petroleum System

International Nuclear Information System (INIS)

Frost, B.R.; Griffith, R.C.

2002-01-01

Current petroleum system models for the Gulf of Guinea propose Tertiary-age deltaic organic material as the principal source for the hydrocarbons found there. Although previous workers recognized numerous difficulties and inconsistencies, no alternative model has been resented to adequately explain the complete petroleum system. We propose that the principal source rock for the Gulf of Guinea system occurs in upper lower Cretaceous-age shales at the rift-drift transition. Tertiary loading and the consequent maturation of this lower Cretaceous source rock can explain the controls on tap formation, reservoir distribution and hydrocarbon types found in the Gulf of Guinea

75 FR 37430 - Plymouth Rock Energy, LLC; Supplemental Notice That Initial Market-Based Rate Filing Includes...

Science.gov (United States)

2010-06-29

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. ER10-1470-000] Plymouth Rock Energy, LLC; Supplemental Notice That Initial Market-Based Rate Filing Includes Request for Blanket... of Plymouth Rock Energy, LLC.'s application for market-based rate authority, with an accompanying...

Evaluation on occluded hydrocarbon in deep–ultra deep ancient source rocks and its cracked gas resources

Directory of Open Access Journals (Sweden)

Jian Li

2015-12-01

Full Text Available Oil-cracked gas, as the main type of high-over mature marine natural gas in China, is mainly derived from occluded hydrocarbon. So it is significant to carry out quantitative study on occluded hydrocarbon. In this paper, the occluded hydrocarbon volume of the main basins in China was calculated depending on their types, abundances and evolution stages by means of the forward method (experimental simulation and the inversion method (geologic profile dissection. And then, occluded hydrocarbon evolution models were established for five types of source rocks (sapropelic, sapropelic prone hybrid, humic prone hybrid, humic and coal. It is shown that the hydrocarbon expulsion efficiency of sapropelic and sapropelic prone hybrid excellent source rocks is lower than 30% at the low-maturity stage, 30%–60% at the principal oil generation stage, and 50%–80% at the high-maturity stage, which are all about 10% higher than that of humic prone hybrid and humic source rocks at the corresponding stages. The resource distribution and cracked gas expulsion of occluded hydrocarbon since the high-maturity stage of marine source rocks in the Sichuan Basin were preliminarily calculated on the basis of the evolution models. The cracked gas expulsion is 230.4 × 1012 m3 at the high evolution stage of occluded hydrocarbon of the Lower Cambrian Qiongzhusi Fm in this basin, and 12.3 × 1012 m3 from the source rocks of Sinian Doushantuo Fm, indicating good potential for natural gas resources. It is indicated that the favorable areas of occluded hydrocarbon cracked gas in the Qiongzhusi Fm source rocks in the Sichuan Basin include Gaoshiti–Moxi, Ziyang and Weiyuan, covering a favorable area of 4.3 × 104 km2.

Geochemistry of crude oils, seepage oils and source rocks from Belize and Guatemala

DEFF Research Database (Denmark)

Petersen, H.I.; Holland, B.; Nytoft, H.P.

2012-01-01

This study reviews the stratigraphy and the poorly documented petroleum geology of the Belize-Guatemala area in northern Central America. Guatemala is divided by the east-west trending La Libertad arch into the North and South Petén Basins. The arch is the westward continuation of the Maya...... generated from source rocks with similar thermal maturities. The crude oils were generated from marine carbonate source rocks and could be divided into three groups: Group 1 oils come from the North Petén Basin (Guatemala) and the western part of the Corozal Basin (Belize), and have a typical carbonate...

Soil erosion and effluent particle size distribution under different initial conditions and rock fragment coverage

Science.gov (United States)

Jomaa, S.; Barry, D. A.; Brovelli, A.; Heng, B. C. P.; Sander, G. C.; Parlange, J.-Y.

2012-04-01

It is well known that the presence of rock fragments on the soil surface and the soil's initial characteristics (moisture content, surface roughness, bulk density, etc.) are key factors influencing soil erosion dynamics and sediment delivery. In addition, the interaction of these factors increases the complexity of soil erosion patterns and makes predictions more difficult. The aim of this study was (i) to investigate the effect of soil initial conditions and rock fragment coverage on soil erosion yields and effluent particle size distribution and (ii) to evaluate to what extent the rock fragment coverage controls this relationship. Three laboratory flume experiments with constant precipitation rate of 74 mm/h on a loamy soil parcel with a 2% slope were performed. Experiments with duration of 2 h were conducted using the 6-m × 2-m EPFL erosion flume. During each experiment two conditions were considered, a bare soil and a rock fragment-protected (with 40% coverage) soil. The initial soil surface state was varied between the three experiments, from a freshly re-ploughed and almost dry condition to a compacted soil with a well-developed shield layer and high moisture content. Experiments were designed so that rain splash was the primary driver of soil erosion. Results showed that the amount of eroded mass was highly controlled by the initial soil conditions and whether the steady-state equilibrium was un-, partially- or fully- developed during the previous event. Additionally, results revealed that sediment yields and particle size composition in the initial part of an erosion event are more sensitive to the erosion history than the long-time behaviour. This latter appears to be mainly controlled by rainfall intensity. If steady-state was achieved for a previous event, then the next event consistently produced concentrations for each size class that peaked rapidly, and then declined gradually to steady-state equilibrium. If steady state was not obtained, then

A comparison of geochemical features of extracts from coal-seams source rocks with different polarity solvents

Energy Technology Data Exchange (ETDEWEB)

Chen, Jianping; Deng, Chunping; Wang, Huitong

2009-02-15

There exists a great difference in group-type fractions and biomarker distributions of chloroform extracts from coals and coal-seams oils, which makes the source identification of coal-seams oils in sedimentary basins rather difficult. The experiment, in which four different polarity solvents, n-hexane, benzene, dichloromethane and chloroform, were used to extract 9 coal-seams source rocks and 3 typical lacustrine source rocks, showed that the yield of extracts increased gradually with increasing solvent polarity. The distribution features of their n-alkanes, isoprenoids and sterane and terpane biomarkers remained, in general, similar, showing no distinct enrichment or depletion for a certain fraction by any solvent. The compositional analysis on n-hexane and chloroform extracts showed that the absolute amount (concentration) of biomarkers was relatively low for the n-hexane extract but comparatively high for the chloroform extract, this difference became great among coal-seams source rocks but small among lacustrine mudstones. The statistical analysis on the relative amount of the 18 major biomarkers in n-hexane and chloroform extracts from 10 source rock samples showed that extracts with a proportional error for the same biomarker of less than 5% (including the analytical error) accounted for 84% while those with a proportional error over 10% amounted to below 5%. This suggested that the outcome of oil-source correlation made by these biomarkers will be independent of variations in amounts of saturates and biomarkers arising from solvent polarity. Therefore, biomarkers obtained from organic-rich source rocks including coals by the extraction with the commonly used chloroform solvent can be applied for the oilsource correlation of coal-seams petroliferous basins.

Factors controlling leaching of polycyclic aromatic hydrocarbons from petroleum source rock using nonionic surfactant

Energy Technology Data Exchange (ETDEWEB)

Akinlua, Akinsehinwa [Obafemi Awolowo Univ., Ile-Ife (Nigeria). Fossil Fuels and Environmental Geochemistry Group; Jochmann, Maik A.; Qian, Yuan; Schmidt, Torsten C. [Duisburg-Essen Univ., Essen (Germany). Instrumental Analytical Chemistry; Sulkowski, Martin [Duisburg-Essen Univ., Essen (Germany). Inst. of Environmental Analytical Chemistry

2012-03-15

The extraction of polycyclic aromatic hydrocarbons (PAHs) from petroleum source rock by nonionic surfactants with the assistance of microwave irradiation was investigated and the conditions for maximum yield were determined. The results showed that the extraction temperatures and type of surfactant have significant effects on extraction yields of PAHs. Factors such as surfactant concentration, irradiation power, sample/solvent ratio and mixing surfactants (i.e., mixture of surfactant at specific ratio) also influence the extraction efficiencies for these compounds. The optimum temperature for microwave-assisted nonionic surfactant extraction of PAHs from petroleum source rock was 120 C and the best suited surfactant was Brij 35. The new method showed extraction efficiencies comparable to those afforded by the Soxhlet extraction method, but a reduction of the extraction times and environmentally friendliness of the new nonionic surfactant extraction system are clear advantages. The results also show that microwave-assisted nonionic surfactant extraction is a good and efficient green analytical preparatory technique for geochemical evaluation of petroleum source rock. (orig.)

19 CFR 10.532 - Integrated Sourcing Initiative.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Integrated Sourcing Initiative. 10.532 Section 10... Trade Agreement Rules of Origin § 10.532 Integrated Sourcing Initiative. (a) For purposes of General... Sourcing Initiative if: (1) The good, in its condition as imported, is both classified in a tariff...

Petroleum source-rock potentials of the cretaceous transgressive-regressive sedimentary sequences of the Cauvery Basin

Science.gov (United States)

Chandra, Kuldeep; Philip, P. C.; Sridharan, P.; Chopra, V. S.; Rao, Brahmaji; Saha, P. K.

The present work is an attempt to contribute to knowledge on the petroleum source-rock potentials of the marine claystones and shales of basins associated with passive continental margins where the source-rock developments are known to have been associated with the anoxic events in the Mesozoic era. Data on three key exploratory wells from three major depressions Ariyallur-Pondicherry, Thanjavur and Nagapattinam of the Cauvery Basin are described and discussed. The average total organic carbon contents of the transgressive Pre-Albian-Cinomanian and Coniacian/Santonian claystones/shales range from 1.44 and 1.16%, respectively. The transgressive/regressive Campanian/Maastrichtian claystones contain average total organic carbon varying from 0.62 to 1.19%. The kerogens in all the studied stratigraphic sequences are classified as type-III with Rock-Eval hydrogen indices varying from 30 to 275. The nearness of land masses to the depositional basin and the mainly clastic sedimentation resulted in accumulation and preservation of dominantly type-III kerogens. The Pre-Albian to Cinomanian sequences of peak transgressive zone deposited in deep marine environments have kerogens with a relatively greater proportion of type-II components with likely greater contribution of planktonic organic matters. The global anoxic event associated with the Albian-Cinomanian marine transgression, like in many other parts of the world, has pervaded the Cauvery Basin and favoured development of good source-rocks with type-III kerogens. The Coniacian-Campanian-Maastrichtian transgressive/regressive phase is identified to be relatively of lesser significance for development of good quality source-rocks.

Late Archaean-early Proterozoic source ages of zircons in rocks from the Paleozoic orogen of western Galicia, NW Spain

Energy Technology Data Exchange (ETDEWEB)

Kuijper, R P; Priem, H N.A. [Laboratorium voor Isotopen-Geologie, Amsterdam (Netherlands); Den Tex, E [Rijksuniversiteit Utrecht (Netherlands). Inst. voor Aardwetenschappen

1982-08-01

U-Pb data are reported for nine suites of zircons and three monazites from the Paleozoic orogen in western Galicia: one paragneiss and six orthogneisses from the early Paleozoic basement, and two Carboniferous (ca. 310 Ma old) intrusions of two-mica granite. New whole-rock Rb-Sr analyses, along with earlier data, indicate an age of ca. 470-440 Ma (Ordovician) for the emplacement of the granitic precursors of the orthogneisses. Monazite from the paragneiss also yields an U-Pb age of ca. 470 Ma. From the high initial /sup 87/Sr//sup 86/Sr ratios an involvement of Precambrian continental crust material is evident in the generation of the early Paleozoic suite of granites, while the zircon U-Pb data give evidence of the presence of about 3.0-2.0 Ga old (late Archaean-early Proterozoic) components in the source material. Zircons from the oldest sedimentary rocks in the area, now present as catazonal paragneisses and a likely source for the granites, likewise reveal a provenance age of 3.0-2.0 Ga.

75 FR 42744 - Synergics Roth Rock Wind Energy, LLC; Supplemental Notice That Initial Market-Based Rate Filing...

Science.gov (United States)

2010-07-22

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. ER10-1637-000] Synergics Roth Rock Wind Energy, LLC; Supplemental Notice That Initial Market-Based Rate Filing Includes Request...-referenced proceeding of Synergics Roth Rock Wind Energy, LLC's application for market-based rate authority...

75 FR 42743 - Synergics Roth Rock North Wind Energy, LLC; Supplemental Notice That Initial Market-Based Rate...

Science.gov (United States)

2010-07-22

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. ER10-1673-000] Synergics Roth Rock North Wind Energy, LLC; Supplemental Notice That Initial Market-Based Rate Filing Includes...-referenced proceeding of Synergics Roth Rock North Wind Energy, LLC's application for market- based rate...

76 FR 41238 - Post Rock Wind Power Project, LLC; Supplemental Notice That Initial Market-Based Rate Filing...

Science.gov (United States)

2011-07-13

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. ER11-3959-000] Post Rock Wind Power Project, LLC; Supplemental Notice That Initial Market-Based Rate Filing Includes Request for... Rock Wind Power Project, LLC's application for market-based rate authority, with an accompanying rate...

Effects of Host-rock Fracturing on Elastic-deformation Source Models of Volcano Deflation.

Science.gov (United States)

Holohan, Eoghan P; Sudhaus, Henriette; Walter, Thomas R; Schöpfer, Martin P J; Walsh, John J

2017-09-08

Volcanoes commonly inflate or deflate during episodes of unrest or eruption. Continuum mechanics models that assume linear elastic deformation of the Earth's crust are routinely used to invert the observed ground motions. The source(s) of deformation in such models are generally interpreted in terms of magma bodies or pathways, and thus form a basis for hazard assessment and mitigation. Using discontinuum mechanics models, we show how host-rock fracturing (i.e. non-elastic deformation) during drainage of a magma body can progressively change the shape and depth of an elastic-deformation source. We argue that this effect explains the marked spatio-temporal changes in source model attributes inferred for the March-April 2007 eruption of Piton de la Fournaise volcano, La Reunion. We find that pronounced deflation-related host-rock fracturing can: (1) yield inclined source model geometries for a horizontal magma body; (2) cause significant upward migration of an elastic-deformation source, leading to underestimation of the true magma body depth and potentially to a misinterpretation of ascending magma; and (3) at least partly explain underestimation by elastic-deformation sources of changes in sub-surface magma volume.

Rb-Sr geochronology of the rocks of the Himalayas, Eastern Nepal, (1)

International Nuclear Information System (INIS)

Kai, Kunio

1981-01-01

Rb-Sr isotopic measurements were carried out for whole rock and small sliced rock from the Himalayan gneiss which constitutes the metamorphosed basement of the Tethyan sediments. The results of the measurements on whole rock from the Barun migmatite, the Barun gneiss and the Irkhua gneiss indicate that complete Sr isotopic redistribution occurred about 520 m.y. ago. This age is interpreted as the time of the regional metamorphism. The analytical results of the small sliced slabs of the Himalayan gneiss indicate that Sr isotopic redistribution occurred among the sliced slabs 33.3 +- 13.2 m.y. ago. This age is interpreted as the time of the metamorphism in the sillimanite-amphibolite facies. The high initial 87 Sr/ 86 Sr ratio of 0.7372 +- 0.0031 from the Barun migmatite of the Himalayan gneiss suggests the Precambrian Origin of the source rocks. The analytical results on the sliced slab of the Barun migmatite indicate that the original age of the rocks is about 800 m.y. The rock is interpreted as the remobilized Precambrian crustal rock. The high initial 87 Sr/ 86 Sr ratio of the Barun gneiss and the Irkhua gneiss of the Himalayan gneiss (0.7234 +- 0.0013) indicates also the Precambrian origin of the source rocks. (author)

Plasma Discharge Initiation of Explosives in Rock Blasting Application: A Case Study

International Nuclear Information System (INIS)

Chae, Jae-Ou; Jeong, Young-Jun; Shmelev, V M; Denicaev, A A; Poutchkov, V M; Ravi, V

2006-01-01

A plasma discharge initiation system for the explosive volumetric combustion charge was designed, investigated and developed for practical application. Laboratory scale experiments were carried out before conducting the large scale field tests. The resultant explosions gave rise to less noise, insignificant seismic vibrations and good specific explosive consumption for rock blasting. Importantly, the technique was found to be safe and environmentally friendly

Qualitative and quantitative analysis of Dibenzofuran, Alkyldibenzofurans, and Benzo[b]naphthofurans in crude oils and source rock extracts

Science.gov (United States)

Meijun Li,; Ellis, Geoffrey S.

2015-01-01

Dibenzofuran (DBF), its alkylated homologues, and benzo[b]naphthofurans (BNFs) are common oxygen-heterocyclic aromatic compounds in crude oils and source rock extracts. A series of positional isomers of alkyldibenzofuran and benzo[b]naphthofuran were identified in mass chromatograms by comparison with internal standards and standard retention indices. The response factors of dibenzofuran in relation to internal standards were obtained by gas chromatography-mass spectrometry analyses of a set of mixed solutions with different concentration ratios. Perdeuterated dibenzofuran and dibenzothiophene are optimal internal standards for quantitative analyses of furan compounds in crude oils and source rock extracts. The average concentration of the total DBFs in oils derived from siliciclastic lacustrine rock extracts from the Beibuwan Basin, South China Sea, was 518 μg/g, which is about 5 times that observed in the oils from carbonate source rocks in the Tarim Basin, Northwest China. The BNFs occur ubiquitously in source rock extracts and related oils of various origins. The results of this work suggest that the relative abundance of benzo[b]naphthofuran isomers, that is, the benzo[b]naphtho[2,1-d]furan/{benzo[b]naphtho[2,1-d]furan + benzo[b]naphtho[1,2-d]furan} ratio, may be a potential molecular geochemical parameter to indicate oil migration pathways and distances.

Shale characterization in mass transport complex as a potential source rock: An example from onshore West Java Basin, Indonesia

Science.gov (United States)

Nugraha, A. M. S.; Widiarti, R.; Kusumah, E. P.

2017-12-01

This study describes a deep-water slump facies shale of the Early Miocene Jatiluhur/Cibulakan Formation to understand its potential as a source rock in an active tectonic region, the onshore West Java. The formation is equivalent with the Gumai Formation, which has been well-known as another prolific source rock besides the Oligocene Talang Akar Formation in North West Java Basin, Indonesia. The equivalent shale formation is expected to have same potential source rock towards the onshore of Central Java. The shale samples were taken onshore, 150 km away from the basin. The shale must be rich of organic matter, have good quality of kerogen, and thermally matured to be categorized as a potential source rock. Investigations from petrography, X-Ray diffractions (XRD), and backscattered electron show heterogeneous mineralogy in the shales. The mineralogy consists of clay minerals, minor quartz, muscovite, calcite, chlorite, clinopyroxene, and other weathered minerals. This composition makes the shale more brittle. Scanning Electron Microscope (SEM) analysis indicate secondary porosities and microstructures. Total Organic Carbon (TOC) shows 0.8-1.1 wt%, compared to the basinal shale 1.5-8 wt%. The shale properties from this outcropped formation indicate a good potential source rock that can be found in the subsurface area with better quality and maturity.

Rb-Sr ages and initial 87Sr/86Sr ratios of late paleozoic granitic rocks from northern Chile

International Nuclear Information System (INIS)

Shibata, Ken; Ishihara, Shunso; Ulriksen, C.E.

1984-01-01

Rb-Sr whole-rock isochron ages were determined on three suites of so-called Paleozoic granitic rocks from northern coastal Chile. The granitic rocks from the Valparaiso and Ci Funcho areas are dated as 296.3 +- 5.4 Ma and 262.2 +- 4.6 Ma, respectively, which are in accord with geologically estimated age. The rocks from the Chanaral area is dated as 212.8 +- 8.6 Ma, which is correlated close to the Triassic-Jurassic boundary age. A K-Ar age of 196 +- 6 Ma was obtained on biotite in granite from Esmeralda between Ci Funcho and Chanaral. These age results demonstrate that no Precambrian plutonism occurred in the studied area, and that so-called Paleozoic granitic rocks in the Ci Funcho-Chanaral area are divided into Permian and early Mesozoic in age. Initial 87 Sr/ 86 Sr ratios of the ilmenite-series granitic rocks from the coastal region are 0.70641 (Valparaiso), 0.70635 (Ci Funcho) and 0.70455 (Chanaral). These relatively low ratios deny substantial crustal contribution to the granitoids. The initial ratios of magnetite-series granitoids from porphyry- and manto-type mineralized areas (Chiquicamata, El Salvador and Tocopilla) are as low as 0.70344 to 0.70464. (author)

76 FR 69720 - NaturEner Rim Rock Wind Energy, LLC; Supplemental Notice That Initial Market-Based Rate Filing...

Science.gov (United States)

2011-11-09

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [ Docket No. ER12-295-000] NaturEner Rim Rock Wind Energy, LLC; Supplemental Notice That Initial Market-Based Rate Filing Includes Request for... NaturEner Rim Rock Wind Energy, LLC's application for market-based rate authority, with an accompanying...

Blocking Modification of Eukaryotic Initiation 5A2 Antagonizes Cervical Carcinoma via Inhibition of RhoA/ROCK Signal Transduction Pathway.

Science.gov (United States)

Liu, Xiaojun; Chen, Dong; Liu, Jiamei; Chu, Zhangtao; Liu, Dongli

2017-10-01

Cervical carcinoma is one of the leading causes of cancer-related death for female worldwide. Eukaryotic initiation factor 5A2 belongs to the eukaryotic initiation factor 5A family and is proposed to be a key factor involved in the development of diverse cancers. In the current study, a series of in vivo and in vitro investigations were performed to characterize the role of eukaryotic initiation factor 5A2 in oncogenesis and metastasis of cervical carcinoma. The expression status of eukaryotic initiation factor 5A2 in 15 cervical carcinoma patients was quantified. Then, the effect of eukaryotic initiation factor 5A2 knockdown on in vivo tumorigenicity ability, cell proliferation, cell cycle distribution, and cell mobility of HeLa cells was measured. To uncover the mechanism driving the function of eukaryotic initiation factor 5A2 in cervical carcinoma, expression of members within RhoA/ROCK pathway was detected, and the results were further verified with an RhoA overexpression modification. The level of eukaryotic initiation factor 5A2 in cervical carcinoma samples was significantly higher than that in paired paratumor tissues ( P cycle arrest ( P ROCK I, and ROCK II were downregulated. The above-mentioned changes in eukaryotic initiation factor 5A2 knockdown cells were alleviated by the overexpression of RhoA. The major findings outlined in the current study confirmed the potential of eukaryotic initiation factor 5A2 as a promising prognosis predictor and therapeutic target for cervical carcinoma treatment. Also, our data inferred that eukaryotic initiation factor 5A2 might function in carcinogenesis of cervical carcinoma through an RhoA/ROCK-dependent manner.

Neoproterozoic rift basins and their control on the development of hydrocarbon source rocks in the Tarim Basin, NW China

Science.gov (United States)

Zhu, Guang-You; Ren, Rong; Chen, Fei-Ran; Li, Ting-Ting; Chen, Yong-Quan

2017-12-01

The Proterozoic is demonstrated to be an important period for global petroleum systems. Few exploration breakthroughs, however, have been obtained on the system in the Tarim Basin, NW China. Outcrop, drilling, and seismic data are integrated in this paper to focus on the Neoproterozoic rift basins and related hydrocarbon source rocks in the Tarim Basin. The basin consists of Cryogenian to Ediacaran rifts showing a distribution of N-S differentiation. Compared to the Cryogenian basins, those of the Ediacaran are characterized by deposits in small thickness and wide distribution. Thus, the rifts have a typical dual structure, namely the Cryogenian rifting and Ediacaran depression phases that reveal distinct structural and sedimentary characteristics. The Cryogenian rifting basins are dominated by a series of grabens or half grabens, which have a wedge-shaped rapid filling structure. The basins evolved into Ediacaran depression when the rifting and magmatic activities diminished, and extensive overlapping sedimentation occurred. The distributions of the source rocks are controlled by the Neoproterozoic rifts as follows. The present outcrops lie mostly at the margins of the Cryogenian rifting basins where the rapid deposition dominates and the argillaceous rocks have low total organic carbon (TOC) contents; however, the source rocks with high TOC contents should develop in the center of the basins. The Ediacaran source rocks formed in deep water environment of the stable depressions evolving from the previous rifting basins, and are thus more widespread in the Tarim Basin. The confirmation of the Cryogenian to Ediacaran source rocks would open up a new field for the deep hydrocarbon exploration in the Tarim Basin.

Water - rock interaction in different rock environments

International Nuclear Information System (INIS)

Lamminen, S.

1995-01-01

The study assesses the groundwater geochemistry and geological environment of 44 study sites for radioactive waste disposal. Initially, the study sites were divided by rock type into 5 groups: (1) acid - intermediate rocks, (2) mafic - ultramafic rocks, (3) gabbros, amphibolites and gneisses that contain calc-silicate (skarn) rocks, (4) carbonates and (5) sandstones. Separate assessments are made of acid - intermediate plutonic rocks and of a subgroup that comprises migmatites, granite and mica gneiss. These all belong to the group of acid - intermediate rocks. Within the mafic -ultramafic rock group, a subgroup that comprises mafic - ultramafic plutonic rocks, serpentinites, mafic - ultramafic volcanic rocks and volcanic - sedimentary schists is also evaluated separately. Bedrock groundwaters are classified by their concentration of total dissolved solids as fresh, brackish, saline, strongly saline and brine-class groundwaters. (75 refs., 24 figs., 3 tabs.)

Source rock identification of sediments using trace element ratios and 13C isotope data - a case study from Pondicherry region

International Nuclear Information System (INIS)

Tirumalesh, K.; Kulkarni, U.P.; Singh, Gursharan; Ramakumar, K.L.; Chidambaram, S.

2012-01-01

Compositional characteristics of source rocks are generally well recorded in sedimentary deposits and provide valuable information about nature of source rocks even though weathering, physical sorting and deposition environment influence the sediment geochemistry. In this paper we report major, trace element and 13 C isotope data of cutting samples collected from Quaternary, Tertiary and Cretaceous formations in Pondicherry area. The distribution patterns and inter elemental correlations are used to identify source rock composition and carbon isotope compositions to understand the sediment deposition conditions. Mineralogy of the bulk sediment indicates presence of Quartz, K-feldspar, Calcite, Mg-calcite, Aragonite and Clay minerals. Compared to upper continental crust values most of these sediments show lower concentration of all elements except Ca and Zn at some depths. The depletion is probably associated with weathering of feldspar and removal of elements through solution. This also increases the proportion of quartz relative to source rock. The ratios of redox sensitive elements (Th/U) infer oxic weathering in shallow sediments. Elemental ratios (La/Sc, Th/Sc, Th/Cr, Th/Co) and ternary plots (La-Th-Sc and Th-Hf-Co) indicate contribution of felsic source rocks with varying degree of weathering. These plots also infer the inherent heterogeneity in the source rocks. Hafnium correlations with other trace elements suggest contribution of Tonalitic rocks in addition to granite to these sediments. The geochemical characteristics of the sediments are found to be similar to that of sediments belonging to similar geology in nearby regions. Presence of shallow marine condition during the sedimentation is inferred from the detrital index (DI) values, which is further supported by the presence of fibrous clay minerals in ESEM scans. This study also brings out the utility of δ 13 C information to reinforce the geochemical and mineralogical inferences. (author)

Characteristics of the Triassic Source Rocks of the Aitutu Formation in the (West Timor Basin

Directory of Open Access Journals (Sweden)

Asep Kurnia Permana

2014-12-01

Full Text Available DOI:10.17014/ijog.v1i3.192The Triassic rocks of the (West Timor Basin have been identified that was mainly deposited in the  marine environment. The fine grained clastics and carbonate  rocks of this Triassic marine  facies are considered to be the most promising source rocks potential in this basin. In this paper we present geochemical and petrographic data from outcrop samples of the Triassic carbonate Aitutu Formation, due to emphasized the organic maturation, kerogen type of the organic matter and the origin of the organic matter.  A representative of selected sample were subjected to the Rock-Eval Pyrolisis, vitrinite reflectance and thermal alteration index, bitumen extraction, were analyzed on the GC-MS. The samples were collected from marine deposit of the Triassic Sequence. The TOC values of the analyzed sample range between rich and rich organic richness (0.51% - 9.16%, wt.%, TOC, which consists mainly of type II and III kerogen and the organic matter consider to be predominantly oil/gas prone and gas prone potential. The thermal maturity assessed from Tmax, TAI, and vitrinite reflectance shows an immature to early peak mature stage of the organic matter. The GC-MS analyses of the biomarkers indicate mainly the organic matter derived from mixed source rocks facies containing alga debris and higher plant terrestrial origin.

Water sources for cyanobacteria below desert rocks in the Negev Desert determined by conductivity

OpenAIRE

McKay, Christopher P.

2016-01-01

We present year round meteorological and conductivity measurements of colonized hypolithic rocks in the Arava Valley, Negev Desert, Israel. The data indicate that while dew is common in the Negev it is not an important source of moisture for hypolithic organisms at this site. The dominance of cyanobacteria in the hypolithic community is consistent with predictions that cyanobacteria are confined to habitats supplied by rain. To monitor the presence of liquid water under the small Negev rocks ...

Mechanical study of the Chartreuse Fold-and-Thrust Belt: relationships between fluids overpressure and decollement within the Toarcian source-rock

Science.gov (United States)

Berthelon, Josselin; Sassi, William; Burov, Evgueni

2016-04-01

Many source-rocks are shale and constitute potential detachment levels in Fold-and-Thrust Belts (FTB): the toarcian Schistes-Cartons in the French Chartreuse FTB for example. Their mechanical properties can change during their burial and thermal maturation, as for example when large amount of hydrocarbon fluids are generated. A structural reconstruction of the Chartreuse FTB geo-history places the Toarcian Formation as the major decollement horizon. In this work, a mechanical analysis integrating the fluids overpressuring development is proposed to discuss on the validity of the structural interpretation. At first, an analogue of the Chartreuse Toarcian Fm, the albanian Posidonia Schist, is documented as it can provide insights on its initial properties and composition of its kerogen content. Laboratory characterisation documents the vertical evolution of the mineralogical, geochemical and mechanical parameters of this potential decollement layer. These physical parameters (i.e. Total Organic Carbon (TOC), porosity/permeability relationship, friction coefficient) are used to address overpressure buildup in the frontal part of the Chartreuse FTB with TEMISFlow Arctem Basin modelling approach (Faille et al, 2014) and the structural emplacement of the Chartreuse thrust units using the FLAMAR thermo-mechanical model (Burov et al, 2014). The hydro-mechanical modeling results highlight the calendar, distribution and magnitude of the overpressure that developed within the source-rock in the footwall of a simple fault-bend fold structure localized in the frontal part of the Chartreuse FTB. Several key geological conditions are required to create an overpressure able to fracture the shale-rocks and induce a significant change in the rheological behaviour: high TOC, low permeability, favourable structural evolution. These models highlight the importance of modeling the impact of a diffuse natural hydraulic fracturing to explain fluids propagation toward the foreland within

Evaluation of the quality, thermal maturity and distribution of potential source rocks in the Danish part of the Norwegian–Danish Basin

Directory of Open Access Journals (Sweden)

Kristensen, Lars

2008-11-01

Full Text Available The quality, thermal maturity and distribution of potential source rocks within the Palaeozoic–Mesozoic succession of the Danish part of the Norwegian–Danish Basin have been evaluated on the basis of screening data from over 4000 samples from the pre-Upper Cretaceous succession in 33 wells. The Lower Palaeozoic in the basin is overmature and the Upper Cretaceous – Cenozoic strata have no petroleum generation potential, but the Toarcian marine shales of the Lower Jurassic Fjerritslev Formation (F-III, F-IV members and the uppermost Jurassic – lowermost Cretaceous shales of the Frederikshavn Formation may qualify as potential source rocks in parts of the basin. Neither of these potential source rocks has a basinwide distribution; the present occurrence of the Lower Jurassic shales was primarily determined by regional early Middle Jurassic uplift and erosion. The generation potential of these source rocks is highly variable. The F-III and F-IV members show significant lateral changes in generation capacity, the best-developed source rocks occurring in the basin centre. The combined F-III andF-IV members in the Haldager-1, Kvols-1 and Rønde-1 wells contain ‘net source-rock’ thicknesses (cumulative thickness of intervals with Hydrogen Index (HI >200 mg HC/g TOC of 40 m, 83 m, and 92 m, respectively, displaying average HI values of 294, 369 and 404 mg HC/g TOC. The Mors-1 well contains 123 m of ‘net source rock’ with an average HI of 221 mg HC/g TOC. Parts of the Frederikshavn Formation possess a petroleum generation potential in the Hyllebjerg-1, Skagen-2, Voldum-1 and Terne-1 wells, the latter well containing a c.160 m thick highly oil-prone interval with an average HI of 478 mg HC/g TOC and maximum HI values >500 mg HC/g TOC. The source-rock evaluation suggests that a Mesozoic petroleum system is the most likely in the study area. Two primary plays are possible: (1 the Upper Triassic – lowermost Jurassic Gassum play, and (2the

Sr-Nd isotope systematics of xenoliths in Cenozoic volcanic rocks from SW Japan

International Nuclear Information System (INIS)

Kagami, Hiroo; Iwata, Masatoshi; Iizumi, Shigeru; Nureki, Terukazu.

1993-01-01

Based on new and previously published Sr and Nd isotope data, we examined the petrogenetic relationship between deep crust- and upper mantle-derived xenoliths contained in Cenozoic volcanic rocks and Cretaceous-Paleogene granitoid rocks in SW Japan. The deep crust- and upper mantle-derived mafic to ultramafic xenoliths contained in Cenozoic volcanic rocks from SW Japan have comparable initial Sr and Nd isotope ratios to the Cretaceous-Paleogene granitoid rocks in their respective districts. This may suggest that these xenoliths were genetically related to the Cretaceous-Paleogene granitoid rocks in SW Japan, and that regional variations in Sr and Nd isotope ratios observed in the granitoid rocks are attributed to differences in the geochemistry of the magma sources. (author)

Strontium isotopic geochemistry of intrusive rocks, Puerto Rico, Greater Antilles

International Nuclear Information System (INIS)

Jones, L.M.; Kesler, S.E.

1980-01-01

The strontium isotope geochemistry is given for three Puerto Rican intrusive rocks: the granodioritic Morovis and San Lorenzo plutons and the Rio Blanco stock of quartz dioritic composition. The average calculated initial 87 Sr/ 86 Sr ratios are 0.70370, 0.70355 and 0.70408, respectively. In addition, the San Lorenzo data establish a whole-rock isochron of 71 +- 2 m.y., which agrees with the previously reported K-Ar age of 73 m.y. Similarity of most of the intrusive rocks in the Greater Antilles with respect to their strontium isotopic geochemistry regardless of their major element composition indicates that intrusive magmas with a wide range of composition can be derived from a single source material. The most likely source material, in view of the available isotopic data, is the mantle wedge overlying the subduction zone. (orig.)

Geothermal regime and Jurassic source rock maturity of the Junggar basin, northwest China

Science.gov (United States)

Nansheng, Qiu; Zhihuan, Zhang; Ershe, Xu

2008-01-01

We analyze the thermal gradient distribution of the Junggar basin based on oil-test and well-logging temperature data. The basin-wide average thermal gradient in the depth interval of 0-4000 m is 22.6 °C/km, which is lower than other sedimentary basins in China. We report 21 measured terrestrial heat flow values based on detailed thermal conductivity data and systematical steady-state temperature data. These values vary from 27.0 to 54.1 mW/m 2 with a mean of 41.8 ± 7.8 mW/m 2. The Junggar basin appears to be a cool basin in terms of its thermal regime. The heat flow distribution within the basin shows the following characteristics. (1) The heat flow decreases from the Luliang Uplift to the Southern Depression; (2) relatively high heat flow values over 50 mW/m 2 are confined to the northern part of the Eastern Uplift and the adjacent parts of the Eastern Luliang Uplift and Central Depression; (3) The lowest heat flow of smaller than 35 mW/m 2 occurs in the southern parts of the basin. This low thermal regime of the Junggar basin is consistent with the geodynamic setting, the extrusion of plates around the basin, the considerably thick crust, the dense lithospheric mantle, the relatively stable continental basement of the basin, low heat generation and underground water flow of the basin. The heat flow of this basin is of great significance to oil exploration and hydrocarbon resource assessment, because it bears directly on issues of petroleum source-rock maturation. Almost all oil fields are limited to the areas of higher heat flows. The relatively low heat flow values in the Junggar basin will deepen the maturity threshold, making the deep-seated widespread Permian and Jurassic source rocks in the Junggar basin favorable for oil and gas generation. In addition, the maturity evolution of the Lower Jurassic Badaowan Group (J 1b) and Middle Jurassic Xishanyao Group (J 2x) were calculated based on the thermal data and burial depth. The maturity of the Jurassic

Correlation of the Canol Formation source rock with oil from Norman Wells

Energy Technology Data Exchange (ETDEWEB)

Snowdon, L.R.; Brooks, P.W.; Williams, G.K.; Goodarzi, F.

1987-01-01

The source of the oil at Norman Wells has long been assumed to have been the Canol Formation and/or the Bluefish Member of the Hare Indian Formation. These two units are stratigraphically above and below the Kee Scarp Formation reservoir unit respectively, and are both bituminous shales. A wide range of analytical techniques including Rock-Eval pyrolysis, solvent extraction and fractionation, capillary gas chromatography, gas chromatography-mass spectrometry, and white light and fluorescence microscopy has been used to characterize core samples of these two units and two samples of crude oil from the Norman Wells field. Most of the analytical techniques were insufficiently refined to either differentiate the extracts from each other or to make a definitive oil/source rock correlation. Collision activated decomposition coupled with multiple ion detection mass spectrometry (GC-MS-MS) did provide sufficient chemical compositional detail of the oils and the two potential sources to demonstrate that the Canol Formation has been the effective source of the Normal Wells oil whereas the Bluefish Member has not. The level of thermal maturity of the core samples ranges from immature to moderately mature in the vicinity of the Norman Wells field to overmature for the samples obtained to the west and north of the field. The level of thermal maturity of the oil was observed to be somewhat higher than that of the samples of the source formation directly above the field. It was thus inferred that some lateral migration from more mature areas has occurred but the extent of this migration was not necessarily more than a few to tens of kilometers.

Tectonic control in source rock maturation and oil migration in Trinidad

Energy Technology Data Exchange (ETDEWEB)

Persad, K.M.; Talukdar, S.C.; Dow, W.G. (DGSI, The Woodlands, TX (United States))

1993-02-01

Oil accumulation in Trinidad were sourced by the Upper Cretaceous calcareous shales deposited along the Cretaceous passive margin of northern South America. Maturation of these source rocks, oil generation, migration and re-migration occurred in a foreland basin setting that resulted from interaction between Caribbean and South American plates during Late Oligocene to recent times. During Middle Miocene-Recent times, the foreland basin experienced strong compressional events, which controlled generation, migration, and accumulation of oil in Trinidad. A series of mature source rock kitchens formed in Late Miocene-Recent times in the Southern and Colombus Basins to the east-southeast of the Central Range Thrust. This thrust and associated fratured developed around 12 m.y.b.p. and served as vertical migration paths for the oil generated in Late Miocene time. This oil migrated into submarine fans deposited in the foreland basin axis and older reservoirs deformed into structural traps. Further generation and migration of oil, and re-migration of earlier oil took place during Pliocene-Holocene times, when later thrusting and wrench faulting served as vertical migration paths. Extremely high sedimentation rates in Pliocene-Pleistocene time, concurrent with active faulting, was responsible for very rapid generation of oil and gas. Vertically migrating gas often mixed with earlier migrated oil in overlying reservoirs. This caused depletion of oil in light hydrocarbons with accompanied fractionation among hydrocarbon types resulting in heavier oil in lower reservoirs, enrichment of light hydrocarbons and accumulation of gas-condensates in upper reservoirs. This process led to an oil-gravity stratification within about 10,000 ft of section.

Pb, Sr, and Nd isotopic compositions of a suite of Large Archean, igneous rocks, eastern Beartooth Mountains - Implications for crust-mantle evolution

Science.gov (United States)

Wooden, J. L.; Mueller, P. A.

1988-01-01

Compositionally diverse Late Archean rocks (2.74-2.79 Ga old) from the eastern Beartooth Mountains (Montana and Wyoming) were studied and shown to have the same initial Pb, Sr, and Nd isotopic ratios. Lead and Sr initial ratios are higher and Nd initial values lower than predicted for rocks derived from model mantle sources and strongly indicate the involvement of an older crustal reservoir in the genesis of these rocks. A model involving subduction of continental detritus and contamination of the overlying mantle is suggested.

Evaluation of the nature, origin and potentiality of the subsurface Middle Jurassic and Lower Cretaceous source rocks in Melleiha G-1x well, North Western Desert, Egypt

Directory of Open Access Journals (Sweden)

Mohamed M. El Nady

2015-09-01

Full Text Available The present work aims to evaluate the nature and origin of the source rock potentiality of subsurface Middle Jurassic and Lower Cretaceous source rocks in Melleiha G-1x well. This target was achieved throughout the evaluation of total organic carbon, rock Eval pyrolysis and vitrinite reflectance for fifteen cutting samples and three extract samples collected from Khatatba, Alam El Bueib and Kharita formations in the studied well. The result revealed that the main hydrocarbon of source rocks, for the Middle Jurassic (Khatatba Fm. is mainly mature, and has good capability of producing oil and minor gas. Lower Cretaceous source rocks (Alam El Bueib Fm. are mature, derived from mixed organic sources and have fair to good capability to generate gas and oil. Kharita Formation of immature source rocks originated from terrestrial origin and has poor to fair potential to produce gas. This indicates that Khatatba and Alam El Bueib formations take the direction of increasing maturity far away from the direction of biodegradation and can be considered as effective source potential in the Melleiha G-1x well.

Problems in the K-Ar dating of Quaternary volcanic rocks younger than 1 Ma

International Nuclear Information System (INIS)

Takaoka, Nobuo

1989-01-01

The assumption that the 40 Ar/ 36 Ar ratio of Ar trapped in volcanic rocks at eruption is atmospheric often gives a large systematic error in the K-Ar dating of Quaternary volcanic rocks younger than 1 Ma. There are two possible sources of error, the existence of excess Ar and mass-fractionated, initial Ar. The major source of excess Ar is supposed to be magma. The 40 Ar/ 36 Ar ratio for magmatic Ar in the North-East Japan arc is tentatively estimated to be 340±10 from measurements of Ar in large phenocrysts separated from Quaternary volcanic rocks. Separation of phenocrysts is the most effective to decrease the systematic error caused by excess Ar. The mass-fractionation of initial Ar should give the 38 Ar/ 36 Ar ratio which was changed from the atmospheric ratio. This can be checked by determining the 38 Ar/ 36 Ar ratio in samples. Since the systematic error caused by the mass-fractionated, initial Ar increases greatly with the increasing atmospheric Ar correction, it is important to correct the result for the mass-fractionation. Correction formulae are given. The error sources other than those mentioned above are uncertainty in the blank correction and instabilities in the sensitivity of spectrometer and the Ar isotopic ratio measurement. In order to increase accuracy of the K-Ar age obtained, to check the systematic errors by measuring samples together with standard samples is of great importance in the K-Ar dating of very young volcanic rocks. (author)

Explosion Source Characteristics in Frozen and Unfrozen Rock

National Research Council Canada - National Science Library

Bonner, Jessie L; Leidig, Mark R; Murphy, Katherine; Dougherty, Sara L; Martin, Randolph J

2008-01-01

.... Central Alaska has abrupt lateral boundaries in discontinuous permafrost, and we detonated 3 shots in frozen, saturated rock and 3 shots nearby in unfrozen, dry rock ranging in size from 200 to 350 Ibs...

Biologically-initiated rock crust on sandstone: Mechanical and hydraulic properties and resistance to erosion

Czech Academy of Sciences Publication Activity Database

Slavík, M.; Bruthans, J.; Filippi, Michal; Schweigstillová, Jana; Falteisek, L.; Řihošek, J.

2017-01-01

Roč. 278, FEB 1 (2017), s. 298-313 ISSN 0169-555X R&D Projects: GA ČR GA13-28040S; GA ČR(CZ) GA16-19459S Institutional support: RVO:67985831 ; RVO:67985891 Keywords : biofilm * biocrust * biologically-initiated rock crust * sandstone protection * case hardening Subject RIV: DB - Geology ; Mineralogy; DB - Geology ; Mineralogy (USMH-B) OBOR OECD: Geology; Geology (USMH-B) Impact factor: 2.958, year: 2016

Geochronology and geochemistry of the Early Jurassic Yeba Formation volcanic rocks in southern Tibet: Initiation of back-arc rifting and crustal accretion in the southern Lhasa Terrane

Science.gov (United States)

Wei, Youqing; Zhao, Zhidan; Niu, Yaoling; Zhu, Di-Cheng; Liu, Dong; Wang, Qing; Hou, Zengqian; Mo, Xuanxue; Wei, Jiuchuan

2017-05-01

Understanding the geological history of the Lhasa Terrane prior to the India-Asia collision ( 55 ± 10 Ma) is essential for improved models of syn-collisional and post-collisional processes in the southern Lhasa Terrane. The Miocene ( 18-10 Ma) adakitic magmatism with economically significant porphyry-type mineralization has been interpreted as resulting from partial melting of the Jurassic juvenile crust, but how this juvenile crust was accreted remains poorly known. For this reason, we carried out a detailed study on the volcanic rocks of the Yeba Formation (YF) with the results offering insights into the ways in which the juvenile crust may be accreted in the southern Lhasa Terrane in the Jurassic. The YF volcanic rocks are compositionally bimodal, comprising basalt/basaltic andesite and dacite/rhyolite dated at 183-174 Ma. All these rocks have an arc-like signature with enriched large ion lithophile elements (LILEs; e.g., Rb, Ba and U) and light rare earth elements (LREEs) and depleted high field strength elements (HFSEs; e.g., Nb, Ta, Ti). They also have depleted whole-rock Sr-Nd and zircon Hf isotopic compositions, pointing to significant mantle isotopic contributions. Modeling results of trace elements and isotopes are most consistent with the basalts being derived from a mantle source metasomatized by varying enrichment of subduction components. The silicic volcanic rocks show the characteristics of transitional I-S type granites, and are best interpreted as resulting from re-melting of a mixed source of juvenile amphibole-rich lower crust with reworked crustal materials resembling metagraywackes. Importantly, our results indicate northward Neo-Tethyan seafloor subduction beneath the Lhasa Terrane with the YF volcanism being caused by the initiation of back-arc rifting. The back-arc setting is a likely site for juvenile crustal accretion in the southern Lhasa Terrane.

The rock art of Mwana wa Chentcherere II rock shelter, Malawi : a site-specific study of girls' initiation rock art

NARCIS (Netherlands)

Zubieta, L.F.

2006-01-01

Mwana wa Chentcherere II, or Chentcherere Rock Shelter II, the name by which it was more generally known when it was excavated in 1972, is one of the largest rock painting sites in Malawi. It has been a national monument since 1972 and has been the subject of extensive archaeological research. This

The Chinese Cretaceous Continental Scientific Drilling Project in the Songliao Basin, NE China: Organic-rich source rock evaluation with geophysical logs from Borehole SK-2

Science.gov (United States)

Zhang, X.; Zou, C.

2017-12-01

The Cretaceous strata have been recognized as an important target of oil or gas exploration in the Songliao Basin, northeast China. The second borehole (SK-2) of the Chinese Cretaceous Continental Scientific Drilling Project in the Songliao Basin (CCSD-SK) is the first one to drill through the Cretaceous continental strata in the frame of ICDP. It was designed not only to solve multiple scientific problems (including the Cretaceous paleoenvironment and paleoclimate, as well as deep resources exploration of the Songliao Basin), but also to expect to achieve new breakthroughs in oil and gas exploration. Based on the project, various geophysical log data (including gamma, sonic, resistivity, density etc.) and core samples have been collected from Borehole SK-2. We do research on organic-rich source rocks estimation using various geophysical log data. Firstly, we comprehensively analyzed organic-rich source rocks' geophysical log response characteristics. Then, source rock's identification methods were constructed to identify organic-rich source rocks with geophysical logs. The main identification methods include cross-plot, multiple overlap and Decision Tree method. Finally, the technique and the CARBOLOG method were applied to evaluate total organic carbon (TOC) content from geophysical logs which provide continuous vertical profile estimations (Passey, 1990; Carpentier et al., 1991). The results show that source rocks are widely distributed in Borehole SK-2, over a large depth strata (985 5700m), including Nenjiang, Qingshankou, Denglouku, Yingcheng, Shahezi Formations. The organic-rich source rocks with higher TOC content occur in the Qingshankou (1647 1650m), Denglouku (2534 2887m) and Shahezi (3367 5697m) Formations. The highest TOC content in these formations can reach 10.31%, 6.58%, 12.79% respectively. The bed thickness of organic-rich source rocks in the these formations are totally up to 7.88m, 74.34m, 276.60m respectively. These organic-rich rocks in the

Pb, Sr and Nd isotope geological characteristics and its evolution of Jianchaling rock

International Nuclear Information System (INIS)

Pang Chunyong; Chen Minyang; Xu Wenxin

2003-01-01

It has been a long time debatable subject on the raw material source and its genesis of Jianchaling ultrabasic rock, because the original rock phases, the original mineral compositions, texture and structure, even part of the chemical components of the rocks had been changed completely after many periods and phases of metamorphism. According to the content of Pb, Rb, Sr, Nd elements and their Pb, Sr, Nd isotope compositions of the rocks, together with the isotope geological age of late magmatic activities, the authors analyze the evolution of Pb, Sr, Nd isotope compositions, The inferred initiate Nd isotope ratio of ultrabasic rocks is 0.510233, lower than that of meteorite unity at a corresponding period, its ε Nd(T)>O; The initiate Sr ratios inferred by the isotope geological age ranges from 0.702735 to 0.719028; Projecting the lead isotope compositions on the Pb tectonic evolution model, the result indicates that the raw material of Jianchaling ultrabasic rock coming from the deplete upper mantle. The ultrabasic magma which enrich of Mg, Ni and less S intruded the crust and formed the Jianchaling ultrabasic rock at late Proterozoic era (927 Ma±). The forming time of serpentinite is mostly equal to the granitoid intruding time, showing the intrusion o flate acidic magma caused a large scale alteration of the ultrabasic rocks and formed the meta-ultrabasic phase rock observed today. (authors)

Paleofacies of Eocene Lower Ngimbang Source Rocks in Cepu Area, East Java Basin based on Biomarkers and Carbon-13 Isotopes

Science.gov (United States)

Devi, Elok A.; Rachman, Faisal; Satyana, Awang H.; Fahrudin; Setyawan, Reddy

2018-02-01

The Eocene Lower Ngimbang carbonaceous shales are geochemically proven hydrocarbon source rocks in the East Java Basin. Sedimentary facies of source rock is important for the source evaluation that can be examined by using biomarkers and carbon-13 isotopes data. Furthermore, paleogeography of the source sedimentation can be reconstructed. The case study was conducted on rock samples of Lower Ngimbang from two exploration wells drilled in Cepu area, East Java Basin, Kujung-1 and Ngimbang-1 wells. The biomarker data include GC and GC-MS data of normal alkanes, isoprenoids, triterpanes, and steranes. Carbon-13 isotope data include saturate and aromatic fractions. Various crossplots of biomarker and carbon-13 isotope data of the Lower Ngimbang source samples from the two wells show that the source facies of Lower Ngimbang shales changed from transitional/deltaic setting at Kujung-1 well location to marginal marine setting at Ngimbang-1 well location. This reveals that the Eocene paleogeography of the Cepu area was composed of land area in the north and marine setting to the south. Biomarkers and carbon-13 isotopes are powerful data for reconstructing paleogeography and paleofacies. In the absence of fossils in some sedimentary facies, these geochemical data are good alternatives.

Organic geochemical characterization of terrestrial source rocks of the Triassic Madygen formation (Southern Tien Shan, Kyrgyzstan)

Energy Technology Data Exchange (ETDEWEB)

Berner, U.; Scheeder, G.; Kus, J. [Section Geochemistry of Petroleum and Coal, BGR, Hannover (Germany); Voigt, S.; Schneider, J.W. [Geological Inst., TU Bergakademic Freiberg (Germany)

2009-09-15

Along the northern foothills of the Turkestan-Alai Range (SW Kyrgyzstan), a 1000 to 1500m thick succession of Mesozoic deposits is exposed recording regional changes of the paleo-landscape during Triassic to Cretaceous times. Detailed litho- and biofacies analyses, conducted by the TU Bergakademie Freiberg since 2006, provided for the first time a nearly complete columnar section of the continental Triassic Madygen Formation of Kyrgyzstan. Organic petrographical and organic geochemical methods (including RockEval pyrolyses, and biomarker analyses) have been applied to a suite of terrestrial sedimentary rocks of Triassic age with the intention to identify the depositional environment. Our investigations suggest that the potential source rocks of the terrestrial pluvial Madygen Formation might generate predominantly gaseous hydrocarbons at higher maturities. (orig.)

Proposal of rock mass behavior classification based on convergence measurement in shaft sinking through sedimentary soft rocks

International Nuclear Information System (INIS)

Tsusaka, Kimikazu

2010-01-01

Japan Atomic Energy Agency has been excavating deep shafts through sedimentary soft rocks in Horonobe, Hokkaido. From the viewpoint of the observational construction, site engineers need a practical guide to evaluate the field measurements conducted with shaft sinking. The author analyzed the relationship among initial deformation rate, observed deformation, the ratio of the modulus of elasticity of rock mass to the initial stress, and the magnitude of inelastic behavior of rock based on convergence measurements and investigation of rock mass properties on shaft walls. As a result, the rock mass behavior classification for shaft sinking which consists of three classes was proposed. (author)

Quantitative determination of minor and trace elements in rocks and soils by spark source mass spectrometry

International Nuclear Information System (INIS)

Ure, A.M.; Bacon, J.R.

1978-01-01

Experimental details are given of the quantitative determination of minor and trace elements in rocks and soils by spark source mass spectrometry. The effects of interfering species, and corrections that can be applied, are discussed. (U.K.)

Application of uniaxial confining-core clamp with hydrous pyrolysis in petrophysical and geochemical studies of source rocks at various thermal maturities

Science.gov (United States)

Lewan, Michael D.; Birdwell, Justin E.; Baez, Luis; Beeney, Ken; Sonnenberg, Steve

2013-01-01

Understanding changes in petrophysical and geochemical parameters during source rock thermal maturation is a critical component in evaluating source-rock petroleum accumulations. Natural core data are preferred, but obtaining cores that represent the same facies of a source rock at different thermal maturities is seldom possible. An alternative approach is to induce thermal maturity changes by laboratory pyrolysis on aliquots of a source-rock sample of a given facies of interest. Hydrous pyrolysis is an effective way to induce thermal maturity on source-rock cores and provide expelled oils that are similar in composition to natural crude oils. However, net-volume increases during bitumen and oil generation result in expanded cores due to opening of bedding-plane partings. Although meaningful geochemical measurements on expanded, recovered cores are possible, the utility of the core for measuring petrophysical properties relevant to natural subsurface cores is not suitable. This problem created during hydrous pyrolysis is alleviated by using a stainless steel uniaxial confinement clamp on rock cores cut perpendicular to bedding fabric. The clamp prevents expansion just as overburden does during natural petroleum formation in the subsurface. As a result, intact cores can be recovered at various thermal maturities for the measurement of petrophysical properties as well as for geochemical analyses. This approach has been applied to 1.7-inch diameter cores taken perpendicular to the bedding fabric of a 2.3- to 2.4-inch thick slab of Mahogany oil shale from the Eocene Green River Formation. Cores were subjected to hydrous pyrolysis at 360 °C for 72 h, which represents near maximum oil generation. One core was heated unconfined and the other was heated in the uniaxial confinement clamp. The unconfined core developed open tensile fractures parallel to the bedding fabric that result in a 38 % vertical expansion of the core. These open fractures did not occur in the

Waste-rock interactions in the immediate repository

International Nuclear Information System (INIS)

McCarthy, G.J.

1977-01-01

The high level wastes (HLW's) to be placed underground in rock formations will contain significant amounts of radioactive decay heat for the first hundred-or-so years of isolation. Several physical-chemical changes analogous to natural geochemical processes can occur during this ''thermal period.'' The waste canister can act as a heat source and cause changes in the mineralogy and properties of the surrounding rocks. Geochemically, this is ''contact metamorphism.'' In the event that the canister is corroded and breached, chemical reactions can occur between the HLW, the surrounding rock and possibly the remains of the canister. In a dry repository which has not been backfilled (and thus pressurized) these interactions could be slow at best and with rates decreasing rapidly as the HLW cools. However, significant interactions can occur in years, months or even days under hydrothermal conditions. These conditions could be created by the combination of HLW heat, overburden pressure and water mobilized from the rocks or derived from groundwater intrusion. At the end of the thermal period these interaction products would constitute the actual HLW form (or ''source term'') subject to the low temperature leaching and migration processes under investigation in other laboratories. It is quite possible that these interaction product waste forms will have superior properties compared to the original HLW. Experimental programs initiated at Penn State during the last year aim at determining the nature of any chemical or mineralogical changes in, or interactions between, HLW solids and host rocks under various repository ambients. The accompanying figures describe the simulated HLW forms and the experimental approach and techniques. Studies with basalts as the repository rock are supported by Rockwell Hanford Operations and with shales by the Office of Waste Isolation

Disc cutter wear and rock texture in hard rock TBM tunneling

International Nuclear Information System (INIS)

Koizumi, Yu; Tsusaka, Kimikazu; Tanimoto, Chikaosa; Nakagawa, Shigeo; Fujita, Naoya

2008-01-01

Disc cutter wear in TBM tunneling is caused by initial fragmentation of a solid rock face (the primary fragmentation) and fragmentation of residual rock pieces between a cutterhead and the face (the secondary fragmentation). In two projects through sedimentary and granitic rocks, the authors investigated the relationships between the rate of cutter wear caused by the primary fragmentation, point load index and the grain size and contents of abrasive minerals. As a result, it was found that the tensile strength and the mineral contents of rocks significantly influenced the cutter wear in both projects and thus it is necessary to take into account of rock type. (author)

Discovery and basic characteristics of high-quality source rocks found in the Yuertusi Formation of the Cambrian in Tarim Basin, China

Directory of Open Access Journals (Sweden)

Guangyou Zhu

2016-02-01

Full Text Available The Upper Paleozoic strata of the Tarim Basin have abundant resources of marine oil and gas. In the Tahe area, Halahatang area, and Tazhong area of the basin, many large-scale oilfields have been found. These oilfields have a confirmed oil and gas reserves worth more than 2.5 billion tons and have completed the annual output of more than 14 million tons of marine oil and gas equivalent. The belief that the only main hydrocarbon source rocks are of the Cambrian or Ordovician is still controversial. Chemists have made significant progress and have effectively lead the oil and gas exploration in Tarim Basin. Due to the complexity of the basin and the limitation of samples, the research work, and fine contrast is restricted. In this article, we investigated the Cambrian strata outcrop of Tarim Basin in detail. By analyzing a lot of outcrops, high-quality hydrocarbon source rocks of Yuertusi Formation have been found in more than 10 outcrop points in Aksu region. The source rocks' lithology is black shale with total organic carbon (TOC content that ranges between 2% and 16%. Total organic carbon (TOC of the black shale layer could be as much as 4%–16%, especially in the outcrops of the Yutixi and Shiairike. This by far is the best marine hydrocarbon source rock that was found in China. The source rocks were distributed consistently in the Aksu region, the thickness of which is about 10–15 m. It was formed in a sedimentary environment of a middle gentle slope to a low gentle slope. Organic matter enrichment is controlled by the upwelling currents. The thick strata of dolostone that developed in the Xiaoerblak Formation are considered to be good reservoirs of the beach and microbial reef in the upper strata of Yuertusi Formation. No hydrocarbon source rocks have been found in the outcrop of Xiaoerblak Formation. The thick strata of gyprock and mudstone development are a set of satisfactory cap layer in the Lower Cambrian. This hydrocarbon

Geophysical Prediction Technology Based on Organic Carbon Content in Source Rocks of the Huizhou Sag, the South China Sea

Directory of Open Access Journals (Sweden)

Yang Wei

2017-08-01

Full Text Available Due to the high exploration cost, limited number of wells for source rocks drilling and scarce test samples for the Total Organic Carbon Content (TOC in the Huizhou sag, the TOC prediction of source rocks in this area and the assessment of resource potentials of the basin are faced with great challenges. In the study of TOC prediction, predecessors usually adopted the logging assessment method, since the data is only confined to a “point” and the regional prediction of the source bed in the seismic profile largely depends on the recognition of seismic facies, making it difficult to quantify TOC. In this study, we combined source rock geological characteristics, logging and seismic response and built the mathematical relation between quasi TOC curve and seismic data based on the TOC logging date of a single well and its internal seismic attribute. The result suggested that it was not purely a linear relationship that was adhered to by predecessors, but was shown as a complicated non-linear relationship. Therefore, the neural network algorithm and SVMs were introduced to obtain the optimum relationship between the quasi TOC curve and the seismic attribute. Then the goal of TOC prediction can be realized with the method of seismic inversion.

Extraction of Iodine from Source Rock and Oil for Radioiodine Dating Final Report CRADA No. TC-1550-98

Energy Technology Data Exchange (ETDEWEB)

Moran, J. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Summa, L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-10-19

This was a collaborative effort between the University of California, Lawrence Livermore National Laboratory (LLNL) and Exxon Production Research Company (EPR) to develop improved techniques for extracting, concentrating, and measuring iodine from large volumes of source rock and oil. The purpose of this project was to develop a technique for measuring total iodine extracted from rock, obtain isotopic ratios, and develop age models for samples provided by EPR.

Look! It's Rock'n'roll!

DEFF Research Database (Denmark)

Lindelof, Anja

2007-01-01

, and dates. Consult your library or click here for more information on citing sources. -------------------------------------------------------------------------------- Anja Mølle Lindelof. (2007). Look! it's rock'n'roll! how television participated in shaping the visual genre conventions of popular music...... to personal names, capitalization, and dates. Consult your library or click here for more information on citing sources. -------------------------------------------------------------------------------- Anja Mølle Lindelof. "Look! It's Rock'n'roll! How television participated in shaping the visual genre....... Pay special attention to personal names, capitalization, and dates. Consult your library or click here for more information on citing sources. -------------------------------------------------------------------------------- TY - JOUR T1 - Look! It's Rock'n'roll! How television participated in shaping...

Relating rock avalanche morphology to emplacement processes

Science.gov (United States)

Dufresne, Anja; Prager, Christoph; Bösmeier, Annette

2015-04-01

The morphology, structure and sedimentological characteristics of rock avalanche deposits reflect both internal emplacement processes and external influences, such as runout path characteristics. The latter is mainly predisposed by topography, substrate types, and hydrogeological conditions. Additionally, the geological setting at the source slope controls, e.g. the spatial distribution of accumulated lithologies and hence material property-related changes in morphology, or the maximum clast size and amount of fines of different lithological units. The Holocene Tschirgant rock avalanche (Tyrol, Austria) resulted from failure of an intensely deformed carbonate rock mass on the southeast face of a 2,370-m-high mountain ridge. The initially sliding rock mass rapidly fragmented as it moved towards the floor of the Inn River valley. Part of the 200-250 x 106 m3 (Patzelt 2012) rock avalanche debris collided with and moved around an opposing bedrock ridge and flowed into the Ötz valley, reaching up to 6.3 km from source. Where the Tschirgant rock avalanche spread freely it formed longitudinal ridges aligned along motion direction as well as smaller hummocks. Encountering high topography, it left runup ridges, fallback patterns (i.e. secondary collapse), and compressional morphology (successively elevated, transverse ridges). Further evidence for the mechanical landslide behaviour is given by large volumes of mobilized valley-fill sediments (polymict gravels and sands). These sediments indicate both shearing and compressional faulting within the rock avalanche mass (forming their own morphological units through, e.g. in situ bulldozing or as distinctly different hummocky terrain), but also indicate extension of the spreading landslide mass (i.e. intercalated/injected gravels encountered mainly in morphological depressions between hummocks). Further influences on its morphology are given by the different lithological units. E.g. the transition from massive dolomite

An analysis of natural gas exploration potential in the Qiongdongnan Basin by use of the theory of “joint control of source rocks and geothermal heat”

Directory of Open Access Journals (Sweden)

Zhang Gongcheng

2014-10-01

Full Text Available The Oligocene Yacheng Fm contains the most important source rocks that have been confirmed by exploratory wells in the Qiongdongnan Basin. The efficiency of these source rocks is the key to the breakthrough in natural gas exploration in the study area. This paper analyzes the hydrocarbon potential of each sag in this basin from the perspective of control of both source rocks and geothermal heat. Two types of source rocks occur in the Yacheng Fm, namely mudstone of transitional facies and mudstone of neritic facies. Both of them are dominated by a kerogen of type-III, followed by type-II. Their organic matter abundances are controlled by the amount of continental clastic input. The mudstone of transitional facies is commonly higher in organic matter abundance, while that of neritic facies is lower. The coal-measure source rocks of transitional facies were mainly formed in such environments as delta plains, coastal plains and barrier tidal flat-marshes. Due to the control of Cenozoic lithosphere extension and influence of neotectonism, the geothermal gradient, terrestrial heat flow value (HFV and level of thermal evolution are generally high in deep water. The hot setting not only determines the predominance of gas generation in the deep-water sags, but can promote the shallow-buried source rocks in shallow water into oil window to generate oil. In addition to promoting the hydrocarbon generation of source rocks, the high geothermal and high heat flow value can also speed up the cracking of residual hydrocarbons, thus enhancing hydrocarbon generation efficiency and capacity. According to the theory of joint control of source quality and geothermal heat on hydrocarbon generation, we comprehensively evaluate and rank the exploration potentials of major sags in the Qiongdongnan Basin. These sags are divided into 3 types, of which type-I sags including Yanan, Lingshui, Baodao, Ledong and Huaguang are the highest in hydrocarbon exploration potential.

Climate modeling - a tool for the assessment of the paleodistribution of source and reservoir rocks

Energy Technology Data Exchange (ETDEWEB)

Roscher, M.; Schneider, J.W. [Technische Univ. Bergakademie Freiberg (Germany). Inst. fuer Geologie; Berner, U. [Bundesanstalt fuer Geowissenschaften und Rohstoffe, Hannover (Germany). Referat Organische Geochemie/Kohlenwasserstoff-Forschung

2008-10-23

In an on-going project of BGR and TU Bergakademie Freiberg, numeric paleo-climate modeling is used as a tool for the assessment of the paleo-distribution of organic rich deposits as well as of reservoir rocks. This modeling approach is based on new ideas concerning the formation of the Pangea supercontinent. The new plate tectonic concept is supported by paleo- magnetic data as it fits the 95% confidence interval of published data. Six Permocarboniferous time slices (340, 320, 300, 290, 270, 255 Ma) were chosen within a first paleo-climate modeling approach as they represent the most important changes of the Late Paleozoic climate development. The digital maps have a resolution of 2.8 x 2.8 (T42), suitable for high-resolution climate modeling, using the PLASIM model. CO{sub 2} concentrations of the paleo-atmosphere and paleo-insolation values have been estimated by published methods. For the purpose of validation, quantitative model output, had to be transformed into qualitative parameters in order to be able to compare digital data with qualitative data of geologic indicators. The model output of surface temperatures and precipitation was therefore converted into climate zones. The reconstructed occurrences of geological indicators like aeolian sands, evaporites, reefs, coals, oil source rocks, tillites, phosphorites and cherts were then compared to the computed paleo-climate zones. Examples of the Permian Pangea show a very good agreement between model results and geological indicators. From the modeling approach we are able to identify climatic processes which lead to the deposition of hydrocarbon source and reservoir rocks. The regional assessment of such atmospheric processes may be used for the identification of the paleo-distribution of organic rich deposits or rock types suitable to form hydrocarbon reservoirs. (orig.)

Organic geochemical characterization of potential hydrocarbon source rocks in the upper Benue Trough

International Nuclear Information System (INIS)

Obaje, N. G.; Pearson, M. J.; Suh, C. E.; Dada, S. S.

1999-01-01

The Upper Benue Trough of Nigeria is the northeastern most portion of the Benue rift structure that extends from the northern limit of the Niger Delta in the south to the southern limit of the Chad basin int he northeast. this portion of the trough is made up of two arms: the Gongola Arm and the Yola Arm. Stratigraphic sequence in the Gongola Arm comprises the continental Albian Bima Sandstone, the transitional Cenomanian Yolde Formation and the marine Turonian - Santonian Gongila, Pindiga, and Fika Formations. Overlying these are the continental Campane - Maastrichtian Gombe Sandstone and the Tertiary Kerri - Kerri Formation. In the Yola Arm, the Turonian - Santonian sequence is replaced by the equally marine Dukul, Jessu, Sekuliye Formations, Numanha Shale, and the Lamja Sandstone. Organic geochemical studies have been carried on outcrop sample form the Gongila, Pindiga, Dukul Formations, the Fika shale and the shaly units of the Gombe Sandstone, with the aim of assessing their source rock potential. Gas Chromatography (GC), Gas Chromatography - Mass Spectrometry (C - MS), and Rock Eval Pyrolysis were the major organic geochemical tools employed. Biomaker hydrocarbon signatures obtained from the GC - MS and the Rock Eval Pyrolysis results indicate that all he formations studied, except the Dukul formation, are immature and are all lean in organic matter

Burial history, thermal history and hydrocarbon generation modelling of the Jurassic source rocks in the basement of the Polish Carpathian Foredeep and Outer Carpathians (SE Poland)

Science.gov (United States)

Kosakowski, Paweł; Wróbel, Magdalena

2012-08-01

Burial history, thermal maturity, and timing of hydrocarbon generation were modelled for the Jurassic source rocks in the basement of the Carpathian Foredeep and marginal part of the Outer Carpathians. The area of investigation was bounded to the west by Kraków, to the east by Rzeszów. The modelling was carried out in profiles of wells: Będzienica 2, Dębica 10K, Góra Ropczycka 1K, Goleszów 5, Nawsie 1, Pławowice E1 and Pilzno 40. The organic matter, containing gas-prone Type III kerogen with an admixture of Type II kerogen, is immature or at most, early mature to 0.7 % in the vitrinite reflectance scale. The highest thermal maturity is recorded in the south-eastern part of the study area, where the Jurassic strata are buried deeper. The thermal modelling showed that the obtained organic matter maturity in the initial phase of the "oil window" is connected with the stage of the Carpathian overthrusting. The numerical modelling indicated that the onset of hydrocarbon generation from the Middle Jurassic source rocks was also connected with the Carpathian thrust belt. The peak of hydrocarbon generation took place in the orogenic stage of the overthrusting. The amount of generated hydrocarbons is generally small, which is a consequence of the low maturity and low transformation degree of kerogen. The generated hydrocarbons were not expelled from their source rock. An analysis of maturity distribution and transformation degree of the Jurassic organic matter shows that the best conditions for hydrocarbon generation occurred most probably in areas deeply buried under the Outer Carpathians. It is most probable that the "generation kitchen" should be searched for there.

Philanthropy as a source of funding for nursing initiatives.

Science.gov (United States)

Kleinpell, Ruth M; Start, Rachel; McIntosh, Erik; Worobec, Sophia; Llewellyn, Jane

2014-01-01

Nurse leaders are challenged with ensuring that research and evidence-based practices are being integrated into clinical care. Initiatives such as the Magnet Recognition Program have helped reinforce the importance of advancing nursing practices to integrate best practices, conduct quality improvement initiatives, improve performance metrics, and involve bedside nurses in conducting research and evidence-based practice projects. While seeking research funding is an option for some initiatives, other strategies such as seeking funding from grateful patients or from philanthropic resources are becoming important options for nurse leaders to pursue, as the availability of funding from traditional sources such as professional organizations or federal funding becomes more limited. In addition, more institutions are seeking and applying for funding, increasing the pool of candidates who are vying for existing funding. Seeking alternative sources of funding, such as through philanthropy, becomes a viable option. This article reviews important considerations in seeking funding from philanthropic sources for nursing initiatives. Examples from a multiyear project that focused on promoting a healthy work environment and improving nursing morale are used to highlight strategies that were used to solicit, obtain, and secure extension funding from private foundation funding to support the initiative.

Angola: source rock control for Lower Congo Coastal and Kwanza Basin petroleum systems

Energy Technology Data Exchange (ETDEWEB)

Burwood, R. [Fina Exploration Ltd, Epsom (United Kingdom)

1999-07-01

The purpose of this paper is to provide an overview of petroleum occurrence and provenance for the 1000 km West African Atlantic Margin from Cabinda to mid-Angola. Over this margin the Lower Congo Coastal and Kwanza provinces cumulatively account for reserves of c. 6 gigabarrels oil recoverable (GBOR). These are dominantly reservoired in Pinda carbonate traps of the former basin. However, with production from a range of aggradational wedge, carbonate platform and pre-salt reservoirs, a diversity in oil character presupposes complex hydrocarbon habitats charged by multiple sourcing. Each of these two major Atlantic margin salt basins constitutes a different, source rock driven, hydrocarbon habitat. As classic passive margin pull-apart basins, Early Cretaceous initiated rift events (Pre-rift, Syn-rift I, II, etc.) evolved into the drift phase opening of the southern Atlantic. A striking feature of this progression was widespread evaporite deposition of the Aptian Loeme salt. This separates two distinct sedimentary and tectonic domains of the Pre- and Post-Salt. The core Lower Congo Coastal habitat is dominated by the Pre-Salt Bucomazi Formation sourced 'poly' petroleum system. These lacustrine, often super-rich, sediments reveal considerable organofacies variation between their basin fill (Syn-rift I) and sheet drape (Syn-rift II) development, accounting for the compositional diversity in their progenic petroleums. Of crucial impact is a cognate diversity in their kerogen kinetic behaviour. This controls the conditions and timing of generation and realization of charge potential. With the Lower Congo Coastal habitat extending southwards towards the Ambriz Spur, the Bucomazi facies proper appears restricted to the northern and deeper proto-lake trend. Over the more weakly subsident margins such troughs host inferior sheet drape potential. Elswhere, Upper Cretaceous-Palaeogene marine clastic Iabe Formation sourced petroleum systems are hydrocarbon productive

Theoretical and numerical studies of crack initiation and propagation in rock masses under freezing pressure and far-field stress

Directory of Open Access Journals (Sweden)

Yongshui Kang

2014-10-01

Full Text Available Water-bearing rocks exposed to freezing temperature can be subjected to freeze–thaw cycles leading to crack initiation and propagation, which are the main causes of frost damage to rocks. Based on the Griffith theory of brittle fracture mechanics, the crack initiation criterion, propagation direction, and crack length under freezing pressure and far-field stress are analyzed. Furthermore, a calculation method is proposed for the stress intensity factor (SIF of the crack tip under non-uniformly distributed freezing pressure. The formulae for the crack/fracture propagation direction and length of the wing crack under freezing pressure are obtained, and the mechanism for coalescence of adjacent cracks is investigated. In addition, the necessary conditions for different coalescence modes of cracks are studied. Using the topology theory, a new algorithm for frost crack propagation is proposed, which has the capability to define the crack growth path and identify and update the cracked elements. A model that incorporates multiple cracks is built by ANSYS and then imported into FLAC3D. The SIFs are then calculated using a FISH procedure, and the growth path of the freezing cracks after several calculation steps is demonstrated using the new algorithm. The proposed method can be applied to rocks containing fillings such as detritus and slurry.

Characteristics of source rocks of the Datangpo Fm, Nanhua System, at the southeastern margin of Sichuan Basin and their significance to oil and gas exploration

Directory of Open Access Journals (Sweden)

Zengye Xie

2017-11-01

Full Text Available In recent years, much attention has been paid to the development environment, biogenetic compositions and hydrocarbon generation characteristics of ancient source rocks in the deep strata of the Sichuan Basin because oil and gas exploration extends continuously to the deep and ultra-deep strata and a giant gas field with the explored reserves of more than 1 × 1012 m3 was discovered in the Middle and Upper Proterozoic–Lower Paleozoic strata in the stable inherited paleo-uplift of the central Sichuan Basin. Based on the previous geological research results, outcrop section of the Datangpo Fm, Nanhua System, at the southeastern margin of the Sichuan Basin was observed and the samples taken from the source rocks were tested and analyzed in terms of their organic geochemistry and organic petrology. It is shown that high-quality black shale source rocks of the Datangpo Fm are developed in the tensional background at the southeastern margin of the Sichuan Basin between two glacial ages, i.e., Gucheng and Nantuo ages in the Nanhua Period. Their thickness is 16–180 m and mineral compositions are mainly clay minerals and clastic quartz. Besides, shale in the Datangpo Fm is of high-quality sapropel type source rock with high abundance at an over-mature stage, and it is characterized by low pristane/phytane ratios (0.32–0.83, low gammacerane abundance, high-abundance tricyclic terpane and higher-content C27 and C29 gonane, indicating that biogenetic compositions are mainly algae and microbes in a strong reducing environment with low salinity. It is concluded that the Datangpo Fm source rocks may be developed in the rift of Nanhua System in central Sichuan Basin. Paleo-uplifts and paleo-slopes before the Caledonian are the favorable locations for the accumulation of dispersed liquid hydrocarbons and paleo-reservoirs derived from the Datangpo Fm source rocks. In addition, scale accumulation zones of dispersed organic matter cracking gas and paleo

Experimental leaching of uranium from tuffaceous rocks

International Nuclear Information System (INIS)

Goodell, P.C.; Trentham, R.C.

1980-07-01

The premise to be tested in this work is that felsic volcanic rocks particularly ash-flow tuffs, can serve as source rocks for certain uranium deposits. The applicability of this idea to several geologic environments is investigated. A genetic model is developed dealing with the behavior of uranium during and subsequent to ash-flow tuff deposition. It is based upon previously described investigations, geologic logic, data presented here, and speculation. Ash-flow tuff sequences described in the literature show significant alkali element variation, particularly in thick tuff units. Some variation is attributed to initial magma variations, whereas additional change may be produced during cooling and degassing of the tuff. Uranium variations have been documented in tuff sequences which are assumed to represent magmatic compositions. Uranium may be released during the initial degassing, during hydrothermal alteration, and/or during later diagenesis. Experimental studies have been designed and carried out to simulate natural leaching conditions such as might occur during diagenesis. Synthetic ground waters have been pumped through pulverized uraniferous vitrophyres. Major and minor element contents have been determined. The most significant chemical changes take place quickly, within a matter of days. Several starting and product leachant solutions were analyzed fluorimetrically for uranium. They show significant increases in uranium contents, from less than 1 ppB at the start to greater than 10 ppB maximu. Such leachant solutions might be significant transport agents of uranium given geologic time. Leaching at low temperatures appears to involve a thin surface reaction and diffusion layer. Both dissolution and ion exchange influence the leachant composition. It is also concluded that glassy ash-flow tuffs may serve as uranium source rocks during low temperature diagenetic changes

Geochemistry of coal-measure source rocks and natural gases in deep formations in Songliao Basin, NE China

Energy Technology Data Exchange (ETDEWEB)

Mi, Jingkui; Zhang, Shuichang; Hu, Guoyi; He, Kun [State Key Laboratory for Enhanced Oil Recovery, Beijing (China); Petroleum Geology Research and Laboratory Center, Research Institute of Petroleum Exploration and Development, PetroChina (China); Key Laboratory for Petroleum Geochemistry, China National Petroleum Corp. (China)

2010-12-01

The natural gases developed in deep volcanic rock reservoirs of the Songliao Basin, NE China are characterized by enriched {delta}{sup 13}C value for methane and frequently reversal carbon isotopic distribution pattern. Although many researchers consider such gas type as an abiogenic origin, we believe the natural gases have a biogenic origin mainly except little inorganic gases and the reversal carbon isotopic distribution pattern of gases is caused by mixing of different origin gases. Methane carbon isotopic values for majority samples fall in the range from - 24 permille to - 32 permille, which is heavier than typical coal-type gases in other Chinese basins. There are several reasons caused heavy carbon isotope of methane: (1) Carbon isotopic values of source kerogen are 3-5 permille heavier than these from other basins; (2) Source rocks are at extremely high maturity stage with vitrinite reflectance mostly above 3.0%; (3) Portion of gas is derived from basement mudrock or slate with higher maturity. The observation on the organic from deep formation reveals that there is a relatively high content for liptinite, which reaches approximately 8 to 10%. The macerals component of source rock shows that the source rocks have some ability to generate oil. Small portion of oil was generated from high hydrogen content macerals in coals and shales as proof by oil found in microcrack and in micropore of coal and oil-bearing fluid inclusions grown in volcanic reservoir. The occurrence of pyrobitumen in volcanic reservoir indicates preexisted oil had been cracked into wet gas, and this kind of gas had also been found in gas pools. Heavy isotopic methane is derived from coal at extremely high maturity stage. There may be little inorganic alkane gases in deep layers for their geochemistry and special geological setting of Songliao Basin. Artificial mixing experiments of different origins gases confirm that inorganic gas such as gas from well FS1 mixed with other end members

The influence of normal fault on initial state of stress in rock mass

Directory of Open Access Journals (Sweden)

Tajduś Antoni

2016-03-01

Full Text Available Determination of original state of stress in rock mass is a very difficult task for rock mechanics. Yet, original state of stress in rock mass has fundamental influence on secondary state of stress, which occurs in the vicinity of mining headings. This, in turn, is the cause of the occurrence of a number of mining hazards, i.e., seismic events, rock bursts, gas and rock outbursts, falls of roof. From experience, it is known that original state of stress depends a lot on tectonic disturbances, i.e., faults and folds. In the area of faults, a great number of seismic events occur, often of high energies. These seismic events, in many cases, are the cause of rock bursts and damage to the constructions located inside the rock mass and on the surface of the ground. To estimate the influence of fault existence on the disturbance of original state of stress in rock mass, numerical calculations were done by means of Finite Element Method. In the calculations, it was tried to determine the influence of different factors on state of stress, which occurs in the vicinity of a normal fault, i.e., the influence of normal fault inclination, deformability of rock mass, values of friction coefficient on the fault contact. Critical value of friction coefficient was also determined, when mutual dislocation of rock mass part separated by a fault is impossible. The obtained results enabled formulation of a number of conclusions, which are important in the context of seismic events and rock bursts in the area of faults.

The influence of normal fault on initial state of stress in rock mass

Science.gov (United States)

Tajduś, Antoni; Cała, Marek; Tajduś, Krzysztof

2016-03-01

Determination of original state of stress in rock mass is a very difficult task for rock mechanics. Yet, original state of stress in rock mass has fundamental influence on secondary state of stress, which occurs in the vicinity of mining headings. This, in turn, is the cause of the occurrence of a number of mining hazards, i.e., seismic events, rock bursts, gas and rock outbursts, falls of roof. From experience, it is known that original state of stress depends a lot on tectonic disturbances, i.e., faults and folds. In the area of faults, a great number of seismic events occur, often of high energies. These seismic events, in many cases, are the cause of rock bursts and damage to the constructions located inside the rock mass and on the surface of the ground. To estimate the influence of fault existence on the disturbance of original state of stress in rock mass, numerical calculations were done by means of Finite Element Method. In the calculations, it was tried to determine the influence of different factors on state of stress, which occurs in the vicinity of a normal fault, i.e., the influence of normal fault inclination, deformability of rock mass, values of friction coefficient on the fault contact. Critical value of friction coefficient was also determined, when mutual dislocation of rock mass part separated by a fault is impossible. The obtained results enabled formulation of a number of conclusions, which are important in the context of seismic events and rock bursts in the area of faults.

Organic geochemistry and petrology of oil source rocks, Carpathian Overthrust region, southeastern Poland - Implications for petroleum generation

Science.gov (United States)

Kruge, M.A.; Mastalerz, Maria; Solecki, A.; Stankiewicz, B.A.

1996-01-01

The organic mailer rich Oligocene Menilite black shales and mudstones are widely distributed in the Carpathian Overthrust region of southeastern Poland and have excellent hydrocarbon generation potential, according to TOC, Rock-Eval, and petrographic data. Extractable organic matter was characterized by an equable distribution of steranes by carbon number, by varying amounts of 28,30-dinor-hopane, 18??(H)-oleanane and by a distinctive group of C24 ring-A degraded triterpanes. The Menilite samples ranged in maturity from pre-generative to mid-oil window levels, with the most mature in the southeastern portion of the study area. Carpathian petroleum samples from Campanian Oligocene sandstone reservoirs were similar in biomarker composition to the Menilite rock extracts. Similarities in aliphatic and aromatic hydrocarbon distributions between petroleum asphaltene and source rock pyrolyzates provided further evidence genetically linking Menilite kerogens with Carpathian oils.

Characterization of source rocks and groundwater radioactivity at the Chihuahua valley

Energy Technology Data Exchange (ETDEWEB)

Renteria V, M.; Montero C, M.E.; Reyes C, M.; Herrera P, E.F.; Valenzuela H, M. [Centro de lnvestigacion en Materiales Avanzados, Miguel de Cervantes 120, 31109 Chihuahua, (Mexico); Rodriguez P, A. [World Wildlife Fund (WWF), Chihuahuan Desert Program, Coronado 1005, 31000 Chihuahua (Mexico); Manjon C, G.; Garcia T, R. [Universidad de Sevilla, Departamento de Fisica Aplicada 11, ETS Arquitectura, Av. Reina Mercedes 2, 41012 Sevilla, (Spain); Crespo, T. [Centro de Investigaciones Energeticas, Medioambientales y Tecnologicas (CIEMAT), Av. Complutense 22, 28040 Madrid, (Spain)]. e-mail: elena.montero@cimav.edu.mx

2007-07-01

As part of a scientific research project about alpha radioactivity in groundwater for human consumption at the Chihuahua City, the characterization of rock sources of radioactivity around de Chihuahua valley was developed. The radioactivity of groundwater and sediments was determined, too. The radioactivity of uranium- and thorium- series isotopes contained in rocks was obtained by high resolution gamma-ray spectroscopy. Some representative values are 50 Bq/kg for the mean value of Bi-214 activity, and 121.5 Bq/kg for the highest value at West of the city. The activity of sediments, extracted during wells perforation, was determined using a Nal(TI) detector. A non-reported before uranium ore was localized at the San Marcos range formation. Its outcrops are inside the Chihuahua-Sacramento valley basin and its activity characterization was performed. Unusually high specific uranium activities, determined by alpha spectrometry, were obtained in water, plants, sediments and fish extracted at locations close to outcrops of uranium minerals. The activity of water of the San Marcos dam reached 7.7 Bq/L. The activity of fish, trapped at San Marcos dam, is 0.99 Bq/kg. Conclusions about the contamination of groundwater at North of Chihuahua City were obtained. (Author)

Characterization of source rocks and groundwater radioactivity at the Chihuahua valley

International Nuclear Information System (INIS)

Renteria V, M.; Montero C, M.E.; Reyes C, M.; Herrera P, E.F.; Valenzuela H, M.; Rodriguez P, A.; Manjon C, G.; Garcia T, R.; Crespo, T.

2007-01-01

As part of a scientific research project about alpha radioactivity in groundwater for human consumption at the Chihuahua City, the characterization of rock sources of radioactivity around de Chihuahua valley was developed. The radioactivity of groundwater and sediments was determined, too. The radioactivity of uranium- and thorium- series isotopes contained in rocks was obtained by high resolution gamma-ray spectroscopy. Some representative values are 50 Bq/kg for the mean value of Bi-214 activity, and 121.5 Bq/kg for the highest value at West of the city. The activity of sediments, extracted during wells perforation, was determined using a Nal(TI) detector. A non-reported before uranium ore was localized at the San Marcos range formation. Its outcrops are inside the Chihuahua-Sacramento valley basin and its activity characterization was performed. Unusually high specific uranium activities, determined by alpha spectrometry, were obtained in water, plants, sediments and fish extracted at locations close to outcrops of uranium minerals. The activity of water of the San Marcos dam reached 7.7 Bq/L. The activity of fish, trapped at San Marcos dam, is 0.99 Bq/kg. Conclusions about the contamination of groundwater at North of Chihuahua City were obtained. (Author)

Nd and Sr isotopes and K-Ar ages of the Ulreungdo alkali volcanic rocks in the East Sea, South Korea

International Nuclear Information System (INIS)

Kim Kyuhan; Jang Sunkyung; Tanaka, Tsuyoshi; Nagao, Keisuke

1999-01-01

Temporal geochemical and isotopical variations in the Ulreundgo alkali volcanic rocks provide important constraints on the origin and evolution of the volcanic rocks in relation to backarc basin tectonism. We determined the K-Ar ages, major and trace element contents, and Nd and Sr isotopic rations of the alkali volcanic rocks. The activities of Ulreungdo volcanoes can be divided, on the basis of radiometric ages and field occurrences, into five stages, though their activities range from 1.4 Ma to 0.01 Ma with short volcanic hiatus (ca. 0.05-0.3 Ma). The Nd-Sr isotopic data for Ulreungdo volcanic rocks enable us to conclude that: (1) the source materials of Ulreungdo volcanics are isotopically heterogeneous in composition, which is explained by the mixing of mantle derived magma and continental crustal source rocks. There is no systematic isotopic variations with eruption stages. Particularly, some volcanic rocks of stage 2 and 3 have extremely wide initial 87 Sr/ 86 Sr isotopic variations ranging from 0.7038 to 0.7092, which are influenced by seawater alterations; (2) the Ulreungdo volcanic rocks show EMI characteristic, while volcanic rocks from the Jejudo, Yeong-il and Jeon-gok areas have slightly depleted mantle source characteristics; (3) the trachyandesite of the latest eruption stage was originated from the mantle source materials which differ from other stages. A schematic isotopic evolution model for alkali basaltic magma is presented in the Ulreungdo volcanic island of the backarc basin of Japanese island arc system. (author)

A study of light hydrocarbons (C{sub 4}-C{sub 1}3) in source rocks and petroleum fluid

Energy Technology Data Exchange (ETDEWEB)

Odden, Wenche

2000-07-01

This thesis consists of an introduction and five included papers. Of these, four papers are published in international journals and the fifth was submitted for review in April 2000. Emphasis has been placed on both naturally and artificially generated light hydrocarbons in petroleum fluids and their proposed source rocks as well as direct application of light hydrocarbons to oil/source rock correlations. Collectively, these papers describe a strategy for interpreting the source of the light hydrocarbons in original oils and condensates as well as the source of the asphaltene fractions from the reservoir fluids. The influence of maturity on light hydrocarbon composition has also been evaluated. The papers include (1) compositional data on the light hydrocarbons from thermal extracts and kerogen pyrolysates of sediment samples, (2) light hydrocarbon data of oils and condensates as well as the pyrolysis products of the asphaltenes from these fluids, (3) assessment of compositional alteration effects, such as selective losses of light hydrocarbons due to evaporation, thermal maturity, phase fractionation and biodegradation, (4) comparison of naturally and artificially generated light hydrocarbons, and (5) compound-specific carbon isotope analysis of the whole range of hydrocarbons of all sample types. (author)

IKEA: Global sourcing and sustainable leather initiatives

OpenAIRE

Jiang, Yan; Jia, Fu; Gong, Yu

2018-01-01

Aims: the aim of this teaching case is to illustrate the Sustainable Global Sourcing (SGS) practices of IKEA influenced by its Global Sourcing (GS) strategy and structure aspects through a case study of the sustainable leather initiative.Scope: this study is developed though 20 face-to-face interviews with IKEA managers in both Sweden and China, covering all the major SGS-related departments i.e. purchasing,sustainability, IWAY, and competence center (sustainable project team).Contribution: w...

Development and Initial Validation of a Rock Climbing Craving Questionnaire (RCCQ

Directory of Open Access Journals (Sweden)

Gareth Roderique-Davies

2018-02-01

Full Text Available Conceptual similarities have been identified between experiences of extreme sports athletes and those with drug and behavioral addictions. Evidence suggests rock climbers experience craving and other withdrawal-like states when abstinent from their sport. However, no studies have attempted to quantitatively measure the craving experienced by participants of any extreme sports. Such a measure could allow a greater understanding of the craving experienced by extreme sports athletes and a comparison of these across sports (e.g., surfing and activities (e.g., drug-use. Therefore, using validated craving measures as a template, the aim of the two studies outlined here was to design and preliminarily validate a subjective multidimensional inventory that could be used to measure craving in the sports of rock-climbing and mountaineering (“RCCQ”. The aim of the first study was to investigate the factor structure of a preliminary measure of craving. Climbers (n = 407 completed the RCCQ. A 3-factor model explained 53.65% of the total variance in item scores. All three factors comprised five items each, which were conceptually labeled as “urge to climb” “negative reinforcement” and “positive reinforcement.” The aim of the second study was to validate the 15-item 3-factor RCCQ resulting from Study 1 using confirmatory factor analysis (CFA. Climbers (n = 254 completed the questionnaire under a climbing-related cue condition or a cue-neutral condition. CFA revealed a good model fit and that all individual parameter estimates were significant and standard errors were within reasonable limits once item 13 was removed from Factor 1. Study 1 supports the multi-dimensional nature of rock climbing craving and shows parallels with substance-related craving in reflecting intention and positive (desire and negative (withdrawal reinforcement. Study 2 confirms this factor structure and gives initial validation to the measure with evidence that these

Source rock evaluation and organic geochemistry of Belayim Marine Oil Field, Gulf of Suez, Egypt

Directory of Open Access Journals (Sweden)

Mohamed Abu Al-Atta

2014-09-01

In general, TOC analyses showed that the Nubia-A and B formation sediments are fairly immature compared to good source rocks with very high Hydrogen Index indicative of kerogen type II. The geochemical investigations of two oil samples indicate that the Upper Rudeis oil of Belayim Marine was derived from a marine carbonate rich source, which is relatively rich in algal organic matter and has moderate sulfur content. The maturity of the analyzed oils (about 0.75% R0 falls short from the stage of peak hydrocarbon generation which is known to be reached at about 0.85% R0.

Isotope shifting capacity of rock

International Nuclear Information System (INIS)

Blattner, P.; Department of Scientific and Industrial Research, Lower Hutt

1980-01-01

Any oxygen isotope shifted rock volume exactly defines a past throughput of water. An expression is derived that relates the throughput of an open system to the isotope shift of reservoir rock and present-day output. The small isotope shift of Ngawha reservoir rock and the small, high delta oxygen-18 output are best accounted for by a magmatic water source

Rock mechanics related to Jurassic underburden at Valdemar oil field

DEFF Research Database (Denmark)

Foged, Niels

1999-01-01

.It has been initiated as a feasibility study of the North Jens-1 core 12 taken in the top Jurassic clay shale as a test specimens for integrated petrological, mineralogical and rock mechanical studies. Following topics are studied:(1) Pore pressure generation due to conversion of organic matter...... and deformation properties of the clay shale using the actual core material or outcrop equivalents.(3) Flushing mechanisms for oil and gas from source rocks due to possibly very high pore water pressure creating unstable conditions in deeply burried sedimentsThere seems to be a need for integrating the knowledge...... in a number of geosciences to the benefit of common understanding of important reservoir mechanisms. Rock mechanics and geotechnical modelling might be key points for this understanding of reservoir geology and these may constitute a platform for future research in the maturing and migration from the Jurassic...

Open Source Initiative Powers Real-Time Data Streams

Science.gov (United States)

2014-01-01

Under an SBIR contract with Dryden Flight Research Center, Creare Inc. developed a data collection tool called the Ring Buffered Network Bus. The technology has now been released under an open source license and is hosted by the Open Source DataTurbine Initiative. DataTurbine allows anyone to stream live data from sensors, labs, cameras, ocean buoys, cell phones, and more.

Conditions promoting and restraining agronomic effectiveness of water-insoluble phosphate sources, in particular phosphate rock (PR): I. Indices of phosphate rock use opportunity (PRUOIS) and of phosphate rock suitability for direct use (PRSIDU)

International Nuclear Information System (INIS)

Borlan, Z.; Gavriluta, I.; Soare, M.; Stefanescu, D.; Alexandrescu, A.

2002-01-01

Several issues of phosphate rock (PR) use are discussed in this paper. Maize for green fodder (Zea mays L) and ryegrass (Lolium multiflorum Lam.) were grown in 7 kg of dry soil and in small pots of 1.25 kg dry soil capacity, respectively, on several base unsaturated soils belonging to Hapludoll and Hapludalf soil groups. The amount of phosphate rock (PR) to apply was based on experimental data considering soil adsorbed acidity (Ah), humus content (H 2 ), cation exchange capacity (T), sum of exchangeable bases (SEB) and mobile (easily soluble) phosphate content (P A L) in the soil. The factors were combined in a rock phosphate use, opportunity index of the soil (PRUOIS): PRUOIS=(A h *H 2 *100)/SEB*10 0.0245*P AL Rock phosphate suitability for direct use was evaluated by means of the rate of PR-P dissolution (PRPRS) in a 0.6% ammonium heptamolybdate in 0.01M calcium chloride solution (ppm P) and by carbonate content (%CaCO 3 ) in PR. Both of these parameters combined provided a phosphate rock suitability index for direct use (PRSIDU): PRSIDU [ppmP/min]=PRPRS*(1-0.03*CaCO 3 ) Water insoluble P sources studied were PR from Kola-Russia, Morocco, Kneifiss-Siria, El Hassa-Jordan, Gafsa- Tunisia, North-Carolina (USA), and Arad-Israel. All PRs were compared with TSP applied at the same rate of P. Neither PRUOIS or PRSIDU considered separately could satisfactorily explain the variance of PR efficiency. An index obtained by multiplicative combination of PRUOIS x PRSIDU did correlate significantly with indices on the agronomic efficiency of PR. (author)

Using pattern classification and nuclear forensic signatures to link UOC to source rocks and purification processes

International Nuclear Information System (INIS)

Marks, N.; Robel, M.; Borg, M.; Hutcheon, I.; Kristo, M.

2014-01-01

Nuclear forensics is a scientific discipline interfacing law enforcement, nuclear science and nonproliferation. Information on the history and on the potential origin of unknown nuclear material can be obtained through nuclear forensic analysis. Using commonly available techniques of mass spectrometry, microscopy and x-ray diffraction, we have gained insight into the processing and origin of a suite of uranium ore concentrate (UOC) samples. We have applied chemometric techniques to investigate the relationships between uranium ore deposits and UOC samples in order to identify chemical and isotopic signatures of nuclear forensic importance. We developed multivariate signatures based on elemental concentrations and isotope ratios using a database of characteristics of UOC originating throughout the world. By introducing detailed and specific information about the source rock geology for each sample, we improved our understanding of the preservation of forensic signatures in UOC. Improved characterization of sample processing and provenance allows us to begin to assess the statistical significance of different groupings of samples and identify underlying patterns. Initial results indicate the concentration of uranium in the ore body, the geochemical conditions associated with uranium emplacement, and host rock petrogenesis exert controlling influences on the impurities preserved in UOC. Specific ore processing techniques, particularly those related to In-Situ Recovery, are also reflected in UOC impurity signatures. Stable and radiogenic isotope geochemistry can be used in conjunction with rare earth element patterns and other characteristics to link UOCs to specific geologic deposits of origin. We will present a number of case studies illustrating the ways in which nuclear forensic analysis can provide insight into the ore geology and production and purification processes used to produce UOC. (author)

The impact of source initialization on performance of the FMBMC-ICEU algorithm

International Nuclear Information System (INIS)

Wenner, Michael T.; Haghighat, Alireza

2011-01-01

Recent work in the completely fission matrix based Monte Carlo (FMBMC) eigenvalue methodology showed that the fission matrix coefficients are independent of the source eigenvector in the limit of small mesh sizes. As a result, fission matrix element autocorrelation should be insignificant. We have developed a modified fission matrix based Monte Carlo methodology for achieving unbiased solutions even for high Dominance Ratio (DR) problems. This methodology utilizes an initial source from a deterministic calculation using the PENTRAN 3-D Parallel SN code, autocorrelation and normality tests, and a Monte Carlo Iterated Confidence Interval (ICI) formulation for estimation of uncertainties in the fundamental eigenvalue and eigenfunction. This methodology is referred to as Fission Matrix Based Monte Carlo Initial-source Controlled Elements with Uncertainties (FMBMC-ICEU). In this paper, we will investigate the impact of different starting sources (PENTRAN initialized with a flat source and a boundary source) on the final results of a test problem with high source correlation. It is shown that although the fission matrix element correlation is significantly reduced, a good initial guess is still important within the framework of the FMBMC-ICEU methodology since the FMBMC-ICEU methodology still utilizes a standard source iteration scheme. (author)

Nd and Sr isotopes and K-Ar ages of the Ulreungdo alkali volcanic rocks in the East Sea, South Korea

Energy Technology Data Exchange (ETDEWEB)

Kim Kyuhan; Jang Sunkyung [Ewha Womans Univ., Seoul (Korea); Tanaka, Tsuyoshi; Nagao, Keisuke

1999-07-01

Temporal geochemical and isotopical variations in the Ulreundgo alkali volcanic rocks provide important constraints on the origin and evolution of the volcanic rocks in relation to backarc basin tectonism. We determined the K-Ar ages, major and trace element contents, and Nd and Sr isotopic rations of the alkali volcanic rocks. The activities of Ulreungdo volcanoes can be divided, on the basis of radiometric ages and field occurrences, into five stages, though their activities range from 1.4 Ma to 0.01 Ma with short volcanic hiatus (ca. 0.05-0.3 Ma). The Nd-Sr isotopic data for Ulreungdo volcanic rocks enable us to conclude that: (1) the source materials of Ulreungdo volcanics are isotopically heterogeneous in composition, which is explained by the mixing of mantle derived magma and continental crustal source rocks. There is no systematic isotopic variations with eruption stages. Particularly, some volcanic rocks of stage 2 and 3 have extremely wide initial {sup 87}Sr/{sup 86}Sr isotopic variations ranging from 0.7038 to 0.7092, which are influenced by seawater alterations; (2) the Ulreungdo volcanic rocks show EMI characteristic, while volcanic rocks from the Jejudo, Yeong-il and Jeon-gok areas have slightly depleted mantle source characteristics; (3) the trachyandesite of the latest eruption stage was originated from the mantle source materials which differ from other stages. A schematic isotopic evolution model for alkali basaltic magma is presented in the Ulreungdo volcanic island of the backarc basin of Japanese island arc system. (author)

Rb/Sr geochronology in whole rocks and minerals of the Cumaru granodiorite, Serra dos Gradaus, Para state, Brazil

International Nuclear Information System (INIS)

Lafon, J.M.; Scheller, T.; Pereira, E.D.; Macambira, J.B.

1990-01-01

The Cumaru granodiorite occurs in the Serra dos Gradaus region, southeastern part of the Metallogenic Province of Carajas, Para. Rb-Sr systematics have been provided in whole rocks and minerals for samples of the Cumaru granodiorite thus an age of 2543 ± 53 Ma, with an initial isotopic ratio of 0.70311 ± 34 (MSWD+1.87) was obtained for whole rocks samples. Taking in account that these rocks are not affected by metamorphism and/or deformation, we consider the age of 2543 ± 53 Ma as an emplacement age corresponding to the crystallization of the body. Such an age confirms the existence of a late Archaean plutonic event in the Serra dos Gradaus area and the interpretation of the Cumaru granodiorite as a contemporaneous and cogenetic body of the Juruena type granites (Ca. 2000 Ma old), as proposed previously, must be definitively abandoned. Therefore, Archaean ages for the greenstone belt sequence (Gradaus group) as well as for the Xingu complex in this area are also confirmed, although by indirect evidence. The age obtained implies that the latter represents an Archaean metamorphic basement in the Serra dos Gradaus region rather than the reworking of the late archaean granitics rocks during the Transmazonian orogenic event. The initial isotopic ratio of 0.70311 ± 34 is close to a mantellic or low time of crustal residence source material ratios at the end of Archaean times. Therefore, comparison with isotopic initial ratios of other granitic rocks which occur in the Rio Maria region identifies an evolution line with a Rb-Sr ratio of 0.25 for a crustal source material that would have separated from mantle about 2.8 Ga ago. (author)

Unzen volcanic rocks as heat source of geothermal activity

Energy Technology Data Exchange (ETDEWEB)

Hayashi, Masao; Sugiyama, Hiromi

1987-03-25

Only a few radiometric ages have been reported so far for the Unzen volcanic rocks. In this connection, in order to clarify the relation between volcanism and geothermal activity, fission track ages of zircon seperated from the Unzen volcanic rocks in western Kyushu have been dated. Since all the rocks are thought to be young, the external surface re-etch method was adopted. The results are that the age and standard error of the basal volcaniclastic rocks of the Tatsuishi formation are 0.28 +- 0.05 Ma and 0.25 +- 0.05 Ma. The next oldest Takadake lavas range from 0.26 to 0.20 Ma. The Kusenbudake lavas fall in a narrow range from 0.19 to 0.17 Ma. The latest Fugendake lavas are younger than 0.07 Ma.In conclusion, the most promising site for geothermal power generation is the Unzen hot spring field because of its very high temperature. After that, comes the Obama hot spring field because of the considerable high temperature chemically estimated. In addition, the northwestern area of the Unzen volcanic region will be promising for electric power generation in spite of no geothermal manifestations, since its volcanos are younger than 0.2 Ma. (14 figs, 14 tabs, 22 refs)

A record of spontaneous subduction initiation in the Izu-Bonin-Mariana arc

Science.gov (United States)

Arculus, Richard J.; Ishizuka, Osamu; Bogus, Kara A.; Gurnis, Michael; Hickey-Vargas, Rosemary; Aljahdali, Mohammed H.; Bandini-Maeder, Alexandre N.; Barth, Andrew P.; Brandl, Philipp A.; Drab, Laureen; Do Monte Guerra, Rodrigo; Hamada, Morihisa; Jiang, Fuqing; Kanayama, Kyoko; Kender, Sev; Kusano, Yuki; Li, He; Loudin, Lorne C.; Maffione, Marco; Marsaglia, Kathleen M.; McCarthy, Anders; Meffre, Sebastién; Morris, Antony; Neuhaus, Martin; Savov, Ivan P.; Sena, Clara; Tepley, Frank J., III; van der Land, Cees; Yogodzinski, Gene M.; Zhang, Zhaohui

2015-09-01

The initiation of tectonic plate subduction into the mantle is poorly understood. If subduction is induced by the push of a distant mid-ocean ridge or subducted slab pull, we expect compression and uplift of the overriding plate. In contrast, spontaneous subduction initiation, driven by subsidence of dense lithosphere along faults adjacent to buoyant lithosphere, would result in extension and magmatism. The rock record of subduction initiation is typically obscured by younger deposits, so evaluating these possibilities has proved elusive. Here we analyse the geochemical characteristics of igneous basement rocks and overlying sediments, sampled from the Amami Sankaku Basin in the northwest Philippine Sea. The uppermost basement rocks are areally widespread and supplied via dykes. They are similar in composition and age--as constrained by the biostratigraphy of the overlying sediments--to the 52-48-million-year-old basalts in the adjacent Izu-Bonin-Mariana fore-arc. The geochemical characteristics of the basement lavas indicate that a component of subducted lithosphere was involved in their genesis, and the lavas were derived from mantle source rocks that were more melt-depleted than those tapped at mid-ocean ridges. We propose that the basement lavas formed during the inception of Izu-Bonin-Mariana subduction in a mode consistent with the spontaneous initiation of subduction.

Compound-specific C- and H-isotope compositions of enclosed organic matter in carbonate rocks: Implications for source identification of sedimentary organic matter and paleoenvironmental reconstruction

International Nuclear Information System (INIS)

Xiong Yongqiang; Wang Yanmei; Wang Yongquan; Xu Shiping

2007-01-01

The Bohai Bay Basin is one of the most important oil-producing provinces in China. Molecular organic geochemical characteristics of Lower Paleozoic source rocks in this area have been investigated by analyzing chemical and isotopic compositions of solvent extracts and acid-released organic matter from the Lower Paleozoic carbonate rocks in the Jiyang Sub-basin of the Bohai Bay Basin. The results indicate that enclosed organic matter in carbonate rocks has not been recognizably altered by post-depositional processes. Two end-member compositions are suggested for early organic matter trapped in the Lower Paleozoic carbonate rocks: (1) a source dominated by aquatic organisms and deposited in a relatively deep marine environment and (2) a relatively high saline, evaporative marine depositional environment. In contrast, chemical and isotopic compositions of solvent extracts from these Lower Paleozoic carbonate rocks are relatively complicated, not only inheriting original characteristics of their precursors, but also overprinted by various post-depositional alterations, such as thermal maturation, biodegradation and mixing. Therefore, the integration of both organic matter characteristics can provide more useful information on the origin of organic matter present in carbonate rocks and the environments of their deposition

Compound-specific C- and H-isotope compositions of enclosed organic matter in carbonate rocks: Implications for source identification of sedimentary organic matter and paleoenvironmental reconstruction

Energy Technology Data Exchange (ETDEWEB)

Xiong Yongqiang [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China)], E-mail: xiongyq@gig.ac.cn; Wang Yanmei; Wang Yongquan; Xu Shiping [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China)

2007-11-15

The Bohai Bay Basin is one of the most important oil-producing provinces in China. Molecular organic geochemical characteristics of Lower Paleozoic source rocks in this area have been investigated by analyzing chemical and isotopic compositions of solvent extracts and acid-released organic matter from the Lower Paleozoic carbonate rocks in the Jiyang Sub-basin of the Bohai Bay Basin. The results indicate that enclosed organic matter in carbonate rocks has not been recognizably altered by post-depositional processes. Two end-member compositions are suggested for early organic matter trapped in the Lower Paleozoic carbonate rocks: (1) a source dominated by aquatic organisms and deposited in a relatively deep marine environment and (2) a relatively high saline, evaporative marine depositional environment. In contrast, chemical and isotopic compositions of solvent extracts from these Lower Paleozoic carbonate rocks are relatively complicated, not only inheriting original characteristics of their precursors, but also overprinted by various post-depositional alterations, such as thermal maturation, biodegradation and mixing. Therefore, the integration of both organic matter characteristics can provide more useful information on the origin of organic matter present in carbonate rocks and the environments of their deposition.

Nitrate release from waste rock dumps in the Elk Valley, British Columbia, Canada.

Science.gov (United States)

Mahmood, Fazilatun N; Barbour, S Lee; Kennedy, C; Hendry, M Jim

2017-12-15

The origin, distribution and leaching of nitrate (NO 3 - ) from coal waste rock dumps in the Elk Valley, British Columbia, Canada were defined using chemical and NO 3 - isotope analyses (δ 15 N- and δ 18 O-NO 3 - ) of solids samples of pre- and post-blast waste rock and from thick (up to 180m) unsaturated waste rock dump profiles constructed between 1982 and 2012 as well as water samples collected from a rock drain located at the base of one dump and effluent from humidity cell (HC) and leach pad (LP) tests on waste rock. δ 15 N- and δ 18 O-NO 3 - values and NO 3 - concentrations of waste rock and rock drain waters confirmed the source of NO 3 - in the waste rock to be explosives and that limited to no denitrification occurs in the dump. The average mass of N released during blasting was estimated to be about 3-6% of the N in the explosives. NO 3 - concentrations in the fresh-blast waste rock and recently placed waste rock used for the HC and LP experiments were highly variable, ranging from below detection to 241mg/kg. The mean and median concentrations of these samples ranged from 10-30mg/kg. In this range of concentrations, the initial aqueous concentration of fresh-blasted waste rock could range from approximately 200-600mg NO 3 - -N/L. Flushing of NO 3 - from the HCs, LPs and a deep field profile was simulated using a scale dependent leaching efficiency (f) where f ranged from 5-15% for HCs, to 35-80% for the LPs, to 80-90% for the field profile. Our findings show aqueous phase NO 3 - from blasting residuals is present at highly variable initial concentrations in waste rock and the majority of this NO 3 - (>75%) should be flushed by recharging water during displacement of the first stored water volume. Copyright © 2017 Elsevier B.V. All rights reserved.

Molecular isotopic characterisation of hydrocarbon biomarkers in Palaeocene-Eocene evaporitic, lacustrine source rocks from the Jianghan Basin, China

NARCIS (Netherlands)

Sinninghe Damsté, J.S.; Grice, Kliti; Schouten, S.; Peters, Kenneth E.

1998-01-01

Immature organic matter in lacustrine source rocks from the Jianghan Basin, eastern China, was studied for distributions and stable carbon isotopic compositions (13C) of hydrocarbon biomarkers. All of the bitumens contain isorenieratane (13C ca. −17 ) indicating the presence of Chlorobiaceae, and

Basement Basalts from IODP Site 1438, Amami-Sankaku Basin: Implications for Sources and Melting Processes during Subduction Initiation in the Izu-Bonin-Mariana System

Science.gov (United States)

McCarthy, A. J.; Hickey-Vargas, R.; Yogodzinski, G. M.; Ishizuka, O.; Hocking, B.; Bizimis, M.; Savov, I. P.; Kusano, Y.; Arculus, R. J.

2016-12-01

IODP Expedition 351 Site 1438 is located in the Amami-Sankaku basin, just west of the Kyushu-Palau Ridge (KPR), a remnant of the early Izu-Bonin-Mariana (IBM) volcanic arc. 150 meters of basement basalt were drilled beneath 1460 m of volcaniclastic sediments and sedimentary rock. The age range inferred for these basalts is 51-52 Ma, close to the 48-52 Ma age of basalts associated with subduction initiation in the IBM forearc (forearc basalts or FABs). Site 1438 basement basalts form several distinct subunits, all relatively mafic (MgO = 6-14 %; Mg# = 51-83). Non-fluid-mobile incompatible trace element patterns are profoundly depleted. Sm/Nd (0.34-0.43) and Lu/Hf (0.18-0.37) reach values higher than most normal MORBs while La/Yb (0.31-0.98) and Ti/V (15.8-27.0) are lower. These features are shared with basalts drilled just west of the KPR at ODP Site 1201 and DSDP Site 447, and many FABs. Abundances of fluid-mobile incompatible elements vary together and are correlated with subunits defined by flow margins and rock physical properties, suggesting control by post-eruptive seawater alteration rather than varying inputs of subduction fluids. Hf-Nd isotopes for Site 1438 basement basalts range from (present-day) ɛNd of 7.0 to 9.5 and ɛHf of 14.5 to 19.8 in a well-correlated array. Their more radiogenic Hf-isotope character could indicate an Indian-type MORB source, however, basalts with ɛHf >16.5, are more radiogenic than many Indian MORB. Pb isotope data will help distinguish differing mantle source domains and origins for fluid-mobile elements. Overall, the combined geochemical data indicate that the mantle source of basement basalts in drill sites west of the KPR (1438, 1201, 447) are closely similar to those for FAB, and that as a group, these rocks are more depleted than more than 90% of global MORB. Our interpretation is that both IBM forearc basalts and basalts from drill sites immediately west of the KPR formed by melting of the same uniquely depleted mantle

Origin of a Tertiary oil from El Mahafir wildcat & geochemical correlation to some Muglad source rocks, Muglad basin, Sudan

Science.gov (United States)

Fadul Abul Gebbayin, Omer. I. M.; Zhong, Ningning; Ali Ibrahim, Gulfan; Ali Alzain, Mohamed

2018-01-01

Source rock screening analysis was performed on four stratigraphic units from the Muglad basin namely; Abu Gabra, Zarqa, Ghazal, and Baraka formations using pyrolysis and Vitrinite Reflectance (Ro). Results, integrated with the chromatographic and isotopic data from these rocks extracts and a Tertiary oil from El Mahafir-1 wild cat, were used to determine the origin of the oil. A good organic source within the Middle Abu Gabra Formation is observed in wells El Toor-6 and Neem Deep-1 (TOC, 1.0-2.0% & S2 5.0-10.0 mg C/g rock), with mixed kerogens I, II, & III, and thermally mature (% Ro = 0.74-0.94). The Campanian-Early Maastrichtian sequence, i.e. Zarqa and Ghazal formations are generally poor (TOC, diversity, both in space and time and is characterized by dominant algal input at some areas and or stratigraphic intervals [Elevated tricyclics, higher C29/C30 hopanes (0.5-1.14), and relatively low Gammacerane indices (4.6-14.4)], while mixed with abundant terrigenous material at others. A direct correlation between El Mahafir oil and the Abu Gabra extracts is thus inferred based on: its mixed organic source nature, oxic to sub-oxic depositional environment (Pr/Ph 1.22), relatively low C29/C30 hopanes (0.54), low C28 steranes (29%), and a high gammacerane index (20.5). This is largely supported by the maturity modeling results which suggest generation is only from the Abu Gabra at this location.

Chemical and isotopic studies of granitic Archean rocks, Owl Creek Mountains, Wyoming: Geochronology of an Archean granite, Owl Creek Mountains, Wyoming

International Nuclear Information System (INIS)

Hedge, C.E.; Simmons, K.R.; Stuckless, J.S.

1986-01-01

Rubidium-strontium analyses of whole-rock samples of an Archean granite from the Owl Creek Mountains, Wyo., indicate an intrusive age of 2640 ± 125 Ma. Muscovite-bearing samples give results suggesting that these samples were altered about 2300 Ma. This event may have caused extensive strontium loss from the rocks as potassium feldspar was altered to muscovite. Alteration was highly localized in nature as evidence by unaffected rubidium-strontium mineral ages in the Owl Creek Mountains area. Furthermore, the event probably involved a small volume of fluid relative to the volume of rock because whole-rock δ 18 O values of altered rocks are not distinct from those of unaltered rocks. In contrast to the rubidium-strontium whole-rock system, zircons from the granite have been so severely affected by the alteration event, and possibly by a late-Precambrian uplift event, that the zircon system yields little usable age information. The average initial 87 Sr/ 86 Sr (0.7033 ± 0.0042) calculated from the isochron intercept varies significantly. Calculated initial 87 Sr/ 86 Sr ratios for nine apparently unaltered samples yield a range of 0.7025 to 0.7047. These calculated initial ratios correlate positively with whole-rock δ 18 O values; and, therefore, the granite was probably derived from an isotopically heterogeneous source. The highest initial 87 Sr/ 86 Sr ratio is lower than the lowest reported for the metamorphic rocks intruded by the granite as it would have existed at 2640 Ma. Thus, the metamorphic sequence, at its current level of exposure, can represent no more than a part of the protolith for the granite

Organic maturation levels, thermal history and hydrocarbon source rock potential of the Namurian rocks of the Clare Basin, Ireland

Energy Technology Data Exchange (ETDEWEB)

Goodhue, Robbie; Clayton, Geoffrey [Trinity Coll., Dept. of Geology, Dublin (Ireland)

1999-11-01

Vitrinite reflectance data from two inland cored boreholes confirm high maturation levels throughout the onshore part of the Irish Clare Basin and suggest erosion of 2 to 4 km of late Carboniferous cover and elevated palaeogeothermal gradients in the Carboniferous section. The observed maturation gradients are fully consistent with the published hypothesis of a late Carboniferous/Permian 'superplume' beneath Pangaea but local vertical reversals in gradients also suggest a complex thermal regime probably involving advective heating. The uppermost Visean--lower Namurian Clare Shale is laterally extensive and up to 300 m thick. Although this unit is post-mature, TOC values of up to 15% suggest that it could have considerable hydrocarbon source rock potential in any less mature offshore parts of the basin. (Author)

Rock suitability classification RSC 2012

Energy Technology Data Exchange (ETDEWEB)

McEwen, T. (ed.) [McEwen Consulting, Leicester (United Kingdom); Kapyaho, A. [Geological Survey of Finland, Espoo (Finland); Hella, P. [Saanio and Riekkola, Helsinki (Finland); Aro, S.; Kosunen, P.; Mattila, J.; Pere, T.

2012-12-15

This report presents Posiva's Rock Suitability Classification (RSC) system, developed for locating suitable rock volumes for repository design and construction. The RSC system comprises both the revised rock suitability criteria and the procedure for the suitability classification during the construction of the repository. The aim of the classification is to avoid such features of the host rock that may be detrimental to the favourable conditions within the repository, either initially or in the long term. This report also discusses the implications of applying the RSC system for the fulfilment of the regulatory requirements concerning the host rock as a natural barrier and the site's overall suitability for hosting a final repository of spent nuclear fuel.

Rock suitability classification RSC 2012

International Nuclear Information System (INIS)

McEwen, T.; Kapyaho, A.; Hella, P.; Aro, S.; Kosunen, P.; Mattila, J.; Pere, T.

2012-12-01

This report presents Posiva's Rock Suitability Classification (RSC) system, developed for locating suitable rock volumes for repository design and construction. The RSC system comprises both the revised rock suitability criteria and the procedure for the suitability classification during the construction of the repository. The aim of the classification is to avoid such features of the host rock that may be detrimental to the favourable conditions within the repository, either initially or in the long term. This report also discusses the implications of applying the RSC system for the fulfilment of the regulatory requirements concerning the host rock as a natural barrier and the site's overall suitability for hosting a final repository of spent nuclear fuel

Geochemical investigation of petroleum source rocks by using Rock- Eval data in the Agha-Jari oilfield

Directory of Open Access Journals (Sweden)

Behzad khani

2015-01-01

Full Text Available In this study, 40 drilling cutting of the Pabdeh, Gurpi, kazhdumi and Gadvan Formations from the Agha-Jari Oilfield were analyzed by using Rock-Eval pyrolysis. In order to recognizing sedimentary environmental conditions of studied Formations, they are divided to 4 zones which A (Kazhdumi Formation#187 and C (Kazhdumi Formation#140 zones show reduction conditions by presence of sea organic materials and B (Gadvan Formation #140 and D(Gadvan Formation#187 zones show oxidation conditions by presence of continental organic materials to basin. Based on the Rock-Eval pyrolysis data, the Pabeh, Gurpi, Kazhdumi and Gadvan Formations have variable hydrocarbon generative potential. HI vs. OI plot revealed that the kerogen type in this Formations is a mixed of types II & III. The intensity of matrix effect in the Pabdeh, Gurpi, Kazhdumi and Gadvan Formations was compared by using S2 vs. TOC plot and calculating its regression equation. The results show that the significant amount of S2 adsorption by matrix was happened in the Pabdeh (4.98-6.96 mg HC/gr rock in wells 113 and 121 and Gurpi Formations ‌(4.33 mg HC/gr rock in well 113 which is due to their low thermal maturity‌(Tmax

Geochemical characterization of Parana Basin volcanic rocks: petrogenetic implications

International Nuclear Information System (INIS)

Marques, L.S.

1988-01-01

A detailed study of the geochemical characteristics of Parana Basin volcanic rocks is presented. The results are based on the analyses of major and trace elements of 158 samples. Ninety three of these volcanic samples belong to 8 flow sequences from Rio Grande do Sul and Santa Catarina States. The remaining sixty five samples are distributed over the entire basin. In order to study the influence of crustal contamination processes in changing chemical characteristics of the volcanic rocks, 47 samples representative of the crystalline basement of the southern and southeastern Parana Basin were also analysed. Several petrogenetic models were tested to explain the compocional variability of the volcanic rocks, in particular those of southern region. The results obtained sugest an assimilation-fractional crystallization process as viable to explain the differences of both the chemical characteristics and Sr isotope initial ratios observed in basic and intermediate rocks. A model involving melting processes of basic material, trapped at the base of the crust, with composition similar to low and high TiO 2 basalts appears to be a possibility to originate the Palmas and Chapeco acid melts, respectively. The study of ''uncontaminated'' or poorly contaminated low TiO 2 basic rocks from the southern, central and northern regions shows the existence of significant differences in the geochemical charactetistics according to their geographical occurrence. A similar geochemical diversity is also observed in high TiO 2 basalts and Chapeco volcanics. Differences in incompatible element ratios between low and high TiO 2 ''uncontaminated'' or poorly contaminated basalts suggest that they could have been produced by different degrees of melting in a garnet peridotite source. Geochemical and isotopic (Sr and Nd) data also support the view that basalts from northern and southern regions of Parana Basin originated from mantle source with different composition. (author) [pt

REE enrichment in granite-derived regolith deposits of the southeast United States: Prospective source rocks and accumulation processes

Science.gov (United States)

Foley, Nora K.; Ayuso, Robert A.; Simandl, G.J.; Neetz, M.

2015-01-01

The Southeastern United States contains numerous anorogenic, or A-type, granites, which constitute promising source rocks for REE-enriched ion adsorption clay deposits due to their inherently high concentrations of REE. These granites have undergone a long history of chemical weathering, resulting in thick granite-derived regoliths, akin to those of South China, which supply virtually all heavy REE and Y, and a significant portion of light REE to global markets. Detailed comparisons of granite regolith profiles formed on the Stewartsville and Striped Rock plutons, and the Robertson River batholith (Virginia) indicate that REE are mobile and can attain grades comparable to those of deposits currently mined in China. A REE-enriched parent, either A-type or I-type (highly fractionated igneous type) granite, is thought to be critical for generating the high concentrations of REE in regolith profiles. One prominent feature we recognize in many granites and mineralized regoliths is the tetrad behaviour displayed in REE chondrite-normalized patterns. Tetrad patterns in granite and regolith result from processes that promote the redistribution, enrichment, and fractionation of REE, such as late- to post- magmatic alteration of granite and silicate hydrolysis in the regolith. Thus, REE patterns showing tetrad effects may be a key for discriminating highly prospective source rocks and regoliths with potential for REE ion adsorption clay deposits.

The United States initiative for international radioactive source management (ISRM)

International Nuclear Information System (INIS)

Naraine, N.; Karhnak, J.

1999-01-01

The United States takes seriously the potential problems from uncontrolled radioactive sources. To address these problems, the United States Department of State is leading the development of an initiative for International Radioactive Source Management (ISRM). The Department of State, through a number of Federal and state agencies, regulatory bodies and private industry, will endeavor to provide coordinated support to the international community, particularly through IAEA, to assist in the development and implementation of risk-based clearance levels to support import/export of radioactive contaminated metals and the tracking, management, identification, remediation, and disposition of 'lost sources' entering nation states and targeted industries. The United States believes that the international control of radioactive sources is critical in avoiding wide-spread contamination of the world metal supply. Thus the initiative has four objectives: (1) Protect sources from becoming lost (Tracking management); (2) Identify primary locations where sources have been lost (Stop future losses); (3) Locate lost sources (monitor and retrieve); and (4) Educate and train (deploy knowledge and technology). A number of efforts already underway in the United States support the overall initiative. The EPA has provided a grant to the Conference of Radiation Program Control Directors (CRCPD) to develop a nation-wide program for the disposition of orphaned radioactive sources. This program now has internet visibility and a toll-free telephone number to call for assistance in the disposal of sources. The Nuclear Regulatory Commission (NRC), the Department of Energy (DOE), and other government agencies as well as private companies are assisting CRCPD in this program. The NRC has begun a program to improve control of radioactive sources in the United States, and also intends to promulgate a regulation defining conditions for the release of materials from licensed facilities. The DOE is

Organic petrology and geochemistry of Eocene Suzak bituminous marl, north-central Afghanistan: Depositional environment and source rock potential

Science.gov (United States)

Hackley, Paul C.; Sanfilipo, John

2016-01-01

Organic geochemistry and petrology of Eocene Suzak bituminous marl outcrop samples from Madr village in north-central Afghanistan were characterized via an integrated analytical approach to evaluate depositional environment and source rock potential. Multiple proxies suggest the organic-rich (TOC ∼6 wt.%) bituminous marls are ‘immature’ for oil generation (e.g., vitrinite Ro  1) indicating organic input from marine algae and/or bacterial biomass, and sterane/hopane ratios are low (0.12–0.14). Monoaromatic steroids are dominated by C28clearly indicating a marine setting. High gammacerane index values (∼0.9) are consistent with anoxia stratification and may indicate intermittent saline-hypersaline conditions. Stable C isotope ratios also suggest a marine depositional scenario for the Suzak samples, consistent with the presence of marine foraminifera including abundant planktic globigerinida(?) and rare benthic discocyclina(?) and nummulites(?). Biomarker 2α-methylhopane for photosynthetic cyanobacteria implies shallow photic zone deposition of Madr marls and 3β-methylhopane indicates presence of methanotrophic archaea in the microbial consortium. The data presented herein are consistent with deposition of Suzak bituminous marls in shallow stratified waters of a restricted marine basin associated with the southeastern incipient or proto-Paratethys. Geochemical proxies from Suzak rock extracts (S content, high polar content, C isotopes, normal (αααR) C27–29 steranes, and C29/C30 and C26/C25 hopane ratios) are similar to extant data from Paleogene oils produced to the north in the Afghan-Tajik Basin. This observation may indicate laterally equivalent strata are effective source rocks as suggested by previous workers; however, further work is needed to strengthen oil-source correlations.

New method to determine initial surface water displacement at tsunami source

Science.gov (United States)

Lavrentyev, Mikhail; Romanenko, Alexey; Tatarintsev, Pavel

2013-04-01

Friday, March 11, 2011 at 05:46:23 UTC, Japan was struck by an 8.9-magnitude earthquake near its Northeastern coast. This is one of the largest earthquakes that Japan has ever experienced. Tsunami waves swept away houses and cars and caused massive human losses. To predict tsunami wave parameters better and faster, we propose to improve data inversion scheme and achieve the performance gain of data processing. One of the reasons of inaccurate predictions of tsunami parameters is that very little information is available about the initial disturbance of the sea bed at tsunami source. In this paper, we suggest a new way of improving the quality of tsunami source parameters prediction. Modern computational technologies can accurately calculate tsunami wave propagation over the deep ocean provided that the initial displacement (perturbation of the sea bed at tsunami source) is known [4]. Direct geophysical measurements provide the location of an earthquake hypocenter and its magnitude (the released energy evaluation). Among the methods of determination of initial displacement the following ones should be considered. Calculation through the known fault structure and available seismic information. This method is widely used and provides useful information. However, even if the exact knowledge about rock blocks shifts is given, recalculation in terms of sea bed displacement is needed. This results in a certain number of errors. GPS data analysis. This method was developed after the December 2004 event in the Indian Ocean. A good correlation between dry land based GPS sensors and tsunami wave parameters was observed in the particular case of the West coast of Sumatra, Indonesia. This approach is very unique and can hardly been used in other geo locations. Satellite image analysis. The resolution of modern satellite images has dramatically improved. In the future, correct data of sea surface displacement will probably be available in real time, right after a tsunamigenic

Hydrocarbon potential of Ordovician and Silurian rocks. Siljan Region (Sweden)

Energy Technology Data Exchange (ETDEWEB)

Berner, U. [Bundesanstalt fuer Geowissenschaften und Rohstoffe (BGR), Hannover (Germany); Lehnert, O. [Erlangen-Nuernberg Univ., Erlangen (Germany); Meinhold, G. [Goettingen Univ. (Germany)

2013-08-01

Hydrocarbon exploration in the vicinity of Europe's largest impact structure (Siljan, Central Sweden) focused for years on abiogenic concepts and largely neglected state of the art knowledge on hydrocarbon generation via thermal decomposition of organic matter. In our study we use sedimentary rocks obtained from three drill sites (Mora001, Stumsnaes 1 and Solberga 1) within the ring structure around the central uplift to investigate the hydrocarbon potential of Ordovician and Silurian strata of the region and also for comparison with the shale oil and gas potential of age equivalent rocks of the Baltic Sea. Elemental analyses provided information on concentrations of carbonate and organic carbon, total sulfur as well as on the composition of major and minor elements of the sediments. The data has been used to evaluate the depositional environment and possible diagenetic alterations of the organic matter. RockEval pyrolysis and solvent hydrocarbon extraction gave insight into the hydrocarbon generation potential and the type and thermal maturity of the sediments. From the geochemistry data of the studied wells it is obvious that changes of depositional environments (lacustrine - marine) have occurred during Ordovician and Silurian times. Although, the quality of the organic matter has been influenced in marine and brackish environments through sulfate reduction, we observe for a number of marine and lacustrine sediments a good to excellent preservation of the biological precursors which qualify the sediments as hydrocarbon source rocks (Type II kerogens). Lacustrine source rocks show a higher remaining hydrocarbon potential (up to {proportional_to}550 mg HC per g C{sub org}) than those of marine or brackish environments. Our investigations indicate that the thermal maturity of organic matter of the drill sites has reached the initial stage of oil generation. However, at Mora001 some of the sediments were stained with oil indicating that hydrocarbons have

Effects of explosions in hard rocks

International Nuclear Information System (INIS)

Heuze, F.E.; Walton, O.R.; Maddix, D.M.; Shaffer, R.J.; Butkovich, T.R.

1993-01-01

This work relates to explosions in hard rocks (ex: basalt, granite, limestone...). Hard rock masses typically have a blocky structure created by the existence of geologic discontinuities such as bedding contacts, faults, and joints. At very high pressure - hundreds of kilobars and above - these discontinuities do not act separately, and the rock appears to be an equivalent continuous medium. At stress of a few tens of kilobars and below, the geologic discontinuities control the kinematics of the rock masses. Hence, the simulation of rock dynamics, anywhere but in the very-near source region, should account for those kinematics

Juvenile helium in ancient rocks: II. U-He,K-Ar, Sm-Nd, and Rb-Sr systematics in the Monche Pluton. 3He/4He ratios frozen in uranium-free ultramafic rocks

International Nuclear Information System (INIS)

Tolstikhin, I.N.; Dokuchaeva, V.S.; Kamensky, I.L.; Amelin, Yu.V.

1992-01-01

The important geodynamic parameter, the 3 He/ 4 He ratio in rocks and fluids of the continental crust, is generally decreasing from the mantle values (≅ 10 -5 ) to the radiogenic ratio (≅ 10 -8 ) on the time scale of about 1 Ga or less. However, the ratios, observed in some ancient rocks and minerals, are much higher than the radiogenic value due to a preferential retention of trapped He, when compared with radiogenic helium and/or a low U/ 3 He ratio in a sample. The distribution of He, Ar, Nd, and Sr isotopes, K, Rb, Sm, and U in ultrabasic rocks, in rock-forming minerals, in ores from the 2.49 Ga Monche Pluton, and in basic rocks of the Main Range (the Kola Peninsula) enables one to distinguish sources of the rocks and trapped fluids and outline some peculiarities of petrogenetic and fluid processes. The initial values of var-epsilon Nd (T) = -0.9 ± 0.5 , 87 Sr/ 86 Sr(T) = 0.7021 ± 0.0002, for the 2.49 Ga Monche Pluton are rather similar to these for other layered intrusions of the Baltic Shield. They differ considerably from the model values for the depleted 2.5 Ga old mantle. The observed and rather different sources of 3 He and 4 He as well as the considerable constancy of their ratio in different minerals, separated from both the ultramafic rocks and gabbros, implies: (1) an intensive process of mixing between mantle and crustal components: a melt convection in the chamber may have occurred; (2) the two types of rocks could originate by crystallization differentiation of one and the same melt. Practically all 3 He and 4 He are concentrated in secondary amphiboles; hence the fluid which stimulated the metamorphic process was probably released from the ultramafite-bearing melt

Mass Dependent Fractionation of Hg Isotopes in Source Rocks, Mineral Deposits and Spring Waters of the California Coast Ranges, USA

Science.gov (United States)

Smith, C. N.; Kesler, S. E.; Blum, J. D.; Rytuba, J. J.

2007-12-01

We present here the first study of the isotopic composition of Hg in rocks, ore deposits, and active hydrothermal systems from the California Coast Ranges, one of Earth's largest Hg-depositing systems. The Franciscan Complex and Great Valley Sequence, which form the bedrock in the California Coast Ranges, are intruded and overlain by Tertiary volcanic rocks including the Clear Lake Volcanic Sequence. These rocks contain two types of Hg deposits, hot-spring deposits that form at shallow depths (<300 m) and silica-carbonate deposits that extend to greater depths (200 to 1000 m), as well as active springs and geothermal systems that release Hg to the present surface. The Franciscan Complex and Great Valley Sequence contain clastic sedimentary rocks with higher concentrations of Hg than volcanic rocks of the Clear Lake Volcanic Field. Mean Hg isotope compositions for all three rock units are similar, although the range of values in Franciscan Complex rocks is greater than in either Great Valley or Clear Lake rocks. Hot spring and silica-carbonate Hg deposits have similar average isotopic compositions that are indistinguishable from averages for the three rock units, although δ202Hg values for the Hg deposits have a greater variance than the country rocks. Precipitates from dilute spring and saline thermal waters in the area have similarly large variance and a mean δ202Hg value that is significantly lower than the ore deposits and rocks. These observations indicate there is little or no isotopic fractionation during release of Hg from its source rocks into hydrothermal solutions. Isotopic fractionation does appear to take place during transport and concentration of Hg in deposits, especially in their uppermost parts. Boiling of hydrothermal fluids is likely the most important process causing of the observed Hg isotope fractionation. This should result in the release of Hg with low δ202Hg values into the atmosphere from the top of these hydrothermal systems and a

Water Sources for Cyanobacteria Below Desert Rocks in the Negev Desert Determined by Conductivity

Science.gov (United States)

McKay, Christopher P.

2016-01-01

We present year round meteorological and conductivity measurements of colonized hypolithic rocks in the Arava Valley, Negev Desert, Israel. The data indicate that while dew is common in the Negev it is not an important source of moisture for hypolithic organisms at this site. The dominance of cyanobacteria in the hypolithic community are consistent with predictions that cyanobacteria are confined to habitats supplied by rain. To monitor the presence of liquid water under the small Negev rocks we developed and tested a simple field conductivity system based on two wires placed about 0.5 cm apart. Based on 21 replicates recorded for one year in the Negev we conclude that in natural rains (0.25 mm to 6 mm) the variability between sensor readings is between 20 and 60% decreasing with increasing rain amount. We conclude that the simple small electrical conductivity system described here can be used effectively to monitor liquid water levels in lithic habitats. However, the natural variability of these sensors indicates that several replicates should be deployed. The results and method presented have use in arid desert reclamation programs.

Behaviour of rock-like oxide fuels under reactivity-initiated accident conditions

International Nuclear Information System (INIS)

Kazuyuki, Kusagaya; Takehiko, Nakamura; Makio, Yoshinaga; Hiroshi, Akie; Toshiyuki, Yamashita; Hiroshi, Uetsuka

2002-01-01

Pulse irradiation tests of three types of un-irradiated rock-like oxide (ROX) fuel - yttria-stabilised zirconia (YSZ) single phase, YSZ and spinel (MgAl 2 O 4 ) homogeneous mixture and particle-dispersed YSZ/spinel - were conducted in the Nuclear Safety Research Reactor to investigate the fuel behaviour under reactivity-initiated accident conditions. The ROX fuels failed at fuel volumetric enthalpies above 10 GJ/m 3 , which was comparable to that of un-irradiated UO 2 fuel. The failure mode of the ROX fuels, however, was quite different from that of the UO 2 fuel. The ROX fuels failed with fuel pellet melting and a part of the molten fuel was released out to the surrounding coolant water. In spite of the release, no significant mechanical energy generation due to fuel/coolant thermal interaction was observed in the tested enthalpy range below∼12 GJ/m 3 . The YSZ type and homogenous YSZ/spinel type ROX fuels failed by cladding burst when their temperatures peaked, while the particle-dispersed YSZ/spinel type ROX fuel seemed to have failed by cladding local melting. (author)

The effect of secondary apatite on the initial 87Sr/86Sr ratio determination in granitic rocks: a case study of the Tadamigawa pluton, northeastern Japan

Science.gov (United States)

Wakasugi, Y.; Ichino, K.; Tanioka, Y.; Wakaki, S.; Tsuboi, M.; Ishikawa, T.

2017-12-01

Apatite is a major accessory mineral in igneous rocks. Because Rb contents in apatite are very low, 87Sr/86Sr ratios of magmatic apatite are useful to estimate the initial 87Sr/86Sr ratio (SrI) of igneous rocks. Secondary post-magmatic event such as hydrothermal alteration may also crystallize secondary apatite, which may inhibit the estimation of SrI of igneous rocks. In this study, we examine the effects of secondary apatite on the initial 87Sr/86Sr ratio determination of granitic rocks by using acid leaching technique. Leached apatite samples were first separated from the whole rock powder as a heavy mineral fraction by heavy liquid technique, and the heavy mineral fraction was then leached by 3 M HNO3. The isotopic ratios of Sr and the concentrations of Rb and Sr were analyzed by TIMS and ICP-MS at Kochi Core Center, respectively. The Tadamigawa Older-stage granites, which locate in the Taishaku Mountains at the northeastern part of Japan, intrude into the Ashio Jurassic complex, and the ages of these rocks are late Cretaceous to Paleogene. The U-Pb ages of zircon and the K-Ar ages of biotite for these rocks are c. 100 Ma [1, 2]. Rb-Sr whole-rock isochron age of the pluton is 96.5 ± 1.3 Ma (SrI = 0.70534 ± 0.00003) and it is concordant with other radiometric ages. Rb-Sr mineral isochron ages range from 84.4 to 97.3 Ma and these ages are relatively younger than the Rb-Sr whole-rock isochron age. The difference among radiometric ages may reflect the difference of the closure temperature in each isotopic system. The Tadamigawa Older-stage granites have SrI for Rb-Sr mineral isochron range from 0.7053 to 0.7061 and are very similar to that (0.70534) for Rb-Sr whole-rock isochron. These may suggest that the Tadamigawa Older-stage granites are generated from same parental magma. However, 87Sr/86Sr ratios of the leached apatite samples were 0.70544-0.70856 and are relatively higher than SrI obtained from the Rb-Sr mineral isochrons (0.7053-0.7061). This result

7-GeV Advanced Photon Source Instrumentation Initiative conceptual design report

International Nuclear Information System (INIS)

1992-12-01

In this APS Instrumentation Initiative, 2.5-m-long and 5-m-long insertion-device x-ray sources will be built on 9 straight sections of the APS storage ring, and an additional 9 bending-magnet sources will also be put in use. The front ends for these 18 x-ray sources will be built to contain and safeguard access to these bright x-ray beams. In addition, funds will be provided to build state-of-the-art insertion-device beamlines to meet scientific and technological research demands well into the next century. This new initiative will also include four user laboratory modules and a special laboratory designed to meet the x-ray imaging research needs of the users. The Conceptual Design Report (CDR) for the APS Instrumentation Initiative describes the scope of all the above technical and conventional construction and provides a detailed cost and schedule for these activities. According to these plans, this new initiative begins in FY 1994 and ends in FY 1998. The document also describes the preconstruction R ampersand D plans for the Instrumentation Initiative activities and provides the cost estimates for the required R ampersand D

Failure Mechanisms of Brittle Rocks under Uniaxial Compression

Science.gov (United States)

Liu, Taoying; Cao, Ping

2017-09-01

The behaviour of a rock mass is determined not only by the properties of the rock matrix, but mostly by the presence and properties of discontinuities or fractures within the mass. The compression test on rock-like specimens with two prefabricated transfixion fissures, made by pulling out the embedded metal inserts in the pre-cured period was carried out on the servo control uniaxial loading tester. The influence of the geometry of pre-existing cracks on the cracking processes was analysed with reference to the experimental observation of crack initiation and propagation from pre-existing flaws. Based on the rock fracture mechanics and the stress-strain curves, the evolution failure mechanism of the fissure body was also analyzed on the basis of exploring the law of the compression-shear crack initiation, wing crack growth and rock bridge connection. Meanwhile, damage fracture mechanical models of a compression-shear rock mass are established when the rock bridge axial transfixion failure, tension-shear combined failure, or wing crack shear connection failure occurs on the specimen under axial compression. This research was of significance in studying the failure mechanism of fractured rock mass.

3D Simulation of Multiple Simultaneous Hydraulic Fractures with Different Initial Lengths in Rock

Science.gov (United States)

Tang, X.; Rayudu, N. M.; Singh, G.

2017-12-01

Hydraulic fracturing is widely used technique for extracting shale gas. During this process, fractures with various initial lengths are induced in rock mass with hydraulic pressure. Understanding the mechanism of propagation and interaction between these induced hydraulic cracks is critical for optimizing the fracking process. In this work, numerical results are presented for investigating the effect of in-situ parameters and fluid properties on growth and interaction of multi simultaneous hydraulic fractures. A fully coupled 3D fracture simulator, TOUGH- GFEM is used for simulating the effect of different vital parameters, including in-situ stress, initial fracture length, fracture spacing, fluid viscosity and flow rate on induced hydraulic fractures growth. This TOUGH-GFEM simulator is based on 3D finite volume method (FVM) and partition of unity element method (PUM). Displacement correlation method (DCM) is used for calculating multi - mode (Mode I, II, III) stress intensity factors. Maximum principal stress criteria is used for crack propagation. Key words: hydraulic fracturing, TOUGH, partition of unity element method , displacement correlation method, 3D fracturing simulator

Results of Rb-Sr dating of metamorphic rocks of crystalline complexes of Male Karpaty Mts

International Nuclear Information System (INIS)

Bagdasaryan, G.P.; Gukasyan, P.Kh.; Cambel, B.; Veselsky, J.

1983-01-01

The paper follows up on a recently published paper on Rb-Sr isochrone dating of granitoid rocks of the Male Karpaty Mts. Data are given on comparative statistical analysis of isochrones obtained for the Bratislava and Modra massifs (isochrone of the latter is complemented with the analyses of two new samples) and the results of age determination of metasedimentary rocks of the Pezinok-Pernek zone and the Bratislava area by the Rb-Sr isochrone. Regression analysis shows that there is no statistically significant difference between the age of the Bratislava massif (347+-4 m.y.) and the Modra massif (326+-22 m.y.) and between their initial ratios 87 Sr/ 86 Sr (i.e., they are synchronous, having the same magma source) which makes it possible to calculate uniform value for age. Whole-rock samples of metamorphic and crystalline schists (gneisses) of the Male Karpaty Mts. also determine the isochrone corresponding to the age 387+-38 m.y. (2σ) and initial ratio ( 87 Sr/ 86 Sr)=0.7100+-0.00O8 (2σ). Rb-Sr isotope analyses of several pairs of biotite-crystalline schist (from which biotite was separated) point out that redistribution of Sr isotopes among the mineral phases of rocks takes place during the periplutonic metamorphism, while the whole-rock samples remain chemically closed systems. (author)

Source rock formation evaluation using TOC & Ro log model based on well-log data procesing: study case of Ngimbang formation, North East Java basin

Directory of Open Access Journals (Sweden)

Fatahillah Yosar

2017-01-01

Full Text Available Ngimbang Formation is known as one major source of hydrocarbon supply in the North Eastern Java Basin. Aged Mid-Eocene, Ngimbang is dominated by sedimentary clastic rocks mostly shale, shaly sandstone, and thick layers of limestone (CD Limestone, with thin layers of coal. Although, laboratory analyses show the Ngimbang Formation to be a relatively rich source-rocks, such data are typically too limited to regionally quantify the distribution of organic matter. To adequately sample the formation both horizontally and vertically on a basin–wide scale, large number of costly and time consuming laboratory analyses would be required. Such analyses are prone to errors from a number of sources, and core data are frequently not available at key locations. In this paper, the authors established four TOC (Total Organic Carbon Content logging calculation models; Passey, Schmoker-Hester, Meyer-Nederloff, and Decker/Density Model by considering the geology of Ngimbang. Well data along with its available core data was used to determine the most suitable model to be applied in the well AFA-1, as well as to compare the accuracy of these TOC model values. The result shows good correlation using Decker (TOC Model and Mallick-Raju (Ro- Vitrinite Reflectance Model. Two source rocks potential zones were detected by these log models.

Modeling the Rock Glacier Cycle

Science.gov (United States)

Anderson, R. S.; Anderson, L. S.

2016-12-01

Rock glaciers are common in many mountain ranges in which the ELA lies above the peaks. They represent some of the most identifiable components of today's cryosphere in these settings. Their oversteepened snouts pose often-overlooked hazards to travel in alpine terrain. Rock glaciers are supported by avalanches and by rockfall from steep headwalls. The winter's avalanche cone must be sufficiently thick not to melt entirely in the summer. The spatial distribution of rock glaciers reflects this dependence on avalanche sources; they are most common on lee sides of ridges where wind-blown snow augments the avalanche source. In the absence of rockfall, this would support a short, cirque glacier. Depending on the relationship between rockfall and avalanche patterns, "talus-derived" and "glacier-derived" rock glaciers are possible. Talus-derived: If the spatial distribution of rock delivery is similar to the avalanche pattern, the rock-ice mixture will travel an englacial path that is downward through the short accumulation zone before turning upward in the ablation zone. Advected debris is then delivered to the base of a growing surface debris layer that reduces the ice melt rate. The physics is identical to the debris-covered glacier case. Glacier-derived: If on the other hand rockfall from the headwall rolls beyond the avalanche cone, it is added directly to the ablation zone of the glacier. The avalanche accumulation zone then supports a pure ice core to the rock glacier. We have developed numerical models designed to capture the full range of glacier to debris-covered glacier to rock glacier behavior. The hundreds of meter lengths, tens of meters thicknesses, and meter per year speeds of rock glaciers are well described by the models. The model can capture both "talus-derived" and "glacier-derived" rock glaciers. We explore the dependence of glacier behavior on climate histories. As climate warms, a pure ice debris-covered glacier can transform to a much shorter rock

Interim rock mass properties and conditions for analyses of a repository in crystalline rock

International Nuclear Information System (INIS)

Tammemagi, H.Y.; Chieslar, J.D.

1985-03-01

A summary of rock properties for generic crystalline rock is compiled from literature sources to provide the input data for analyses of a conceptual repository in crystalline rock. Frequency histograms, mean values and ranges of physical, mechanical, thermal, and thermomechanical properties, and the dependence of these properties on temperature are described. A description of the hydrogeologic properties of a crystalline rock mass and their dependence on depth is provided. In addition, the temperature gradients, mean annual surface temperature, and in situ stress conditions are summarized for the three regions of the United States currently under consideration to host a crystalline repository; i.e., the North Central, Northeastern, and Southeastern. Brief descriptions of the regional geology are also presented. Large-scale underground experiments in crystalline rock at Stripa, Sweden, and in Climax Stock in Nevada, are reviewed to assess whether the rock properties presented in this report are representative of in situ conditions. The suitability of each rock property and the sufficiency of its data base are described. 110 refs., 27 figs., 4 tabs

A Study of Porphyrins in Petroleum Source Rocks

Energy Technology Data Exchange (ETDEWEB)

Huseby, Berit

1997-12-31

This thesis discusses several aspects of porphyrin geochemistry. Degradation experiments have been performed on the Messel oil shale (Eocene, Germany) to obtain information on porphyrins bound or incorporated into macromolecular structures. Thermal heating of the preextracted kerogen by hydrous pyrolysis was used to study the release of porphyrins and their temperature dependent changes during simulated diagenesis and catagenesis. Selective chemical degradation experiments were performed on the preextracted sediment to get more detailed information about porphyrins that are specifically bound to the macromolecular structures via ester bonds. From the heating experiments, in a separate study, the porphyrin nitrogen content in the generated bitumens was compared to the bulk of organic nitrogen compounds in the fraction. The bulk nitrogen contents in the generated bitumens, the water phase and the residual organic matter was recorded to establish the distribution of nitrogen between the kerogen and product phases. Porphyrins as biomarkers were examined in naturally matured Kimmeridge clay source rocks (Upper Jurassic, Norway), and the use of porphyrins as general indicators of maturity was evaluated. Underlying maturity trends in the biomarker data was investigated by Partial Least Squares analysis. Porphyrin as indicators of depositional conditions was also addressed, where the correlations between the (amounts) abundance of nickel and vanadyl porphyrins were mapped together with other descriptors that are assumed to be indicative of redox depositional conditions. 252 refs., 28 figs., 4 tabs.

A Study of Porphyrins in Petroleum Source Rocks

Energy Technology Data Exchange (ETDEWEB)

Huseby, Berit

1996-12-31

This thesis discusses several aspects of porphyrin geochemistry. Degradation experiments have been performed on the Messel oil shale (Eocene, Germany) to obtain information on porphyrins bound or incorporated into macromolecular structures. Thermal heating of the preextracted kerogen by hydrous pyrolysis was used to study the release of porphyrins and their temperature dependent changes during simulated diagenesis and catagenesis. Selective chemical degradation experiments were performed on the preextracted sediment to get more detailed information about porphyrins that are specifically bound to the macromolecular structures via ester bonds. From the heating experiments, in a separate study, the porphyrin nitrogen content in the generated bitumens was compared to the bulk of organic nitrogen compounds in the fraction. The bulk nitrogen contents in the generated bitumens, the water phase and the residual organic matter was recorded to establish the distribution of nitrogen between the kerogen and product phases. Porphyrins as biomarkers were examined in naturally matured Kimmeridge clay source rocks (Upper Jurassic, Norway), and the use of porphyrins as general indicators of maturity was evaluated. Underlying maturity trends in the biomarker data was investigated by Partial Least Squares analysis. Porphyrin as indicators of depositional conditions was also addressed, where the correlations between the (amounts) abundance of nickel and vanadyl porphyrins were mapped together with other descriptors that are assumed to be indicative of redox depositional conditions. 252 refs., 28 figs., 4 tabs.

Pre-Messinian (Sub-Salt Source-Rock Potential on Back-Stop Basins of the Hellenic Trench System (Messara Basin, Central Crete, Greece

Directory of Open Access Journals (Sweden)

Maravelis A.

2016-01-01

Full Text Available The Greek part of the Mediterranean Ridge suggests, in terms of its hydrocarbon potential, further frontier exploration. The geological similarities between its prolific portions, within the Cyprus and Egyptian Exclusive Economic Zones, indicate possible recoverable natural gas reserves in its Greek portion. Nevertheless it lacks of systematic frontier exploration although direct petroleum indicators occur. Active mud volcanoes on the Mediterranean Ridge, still emitting concurrently gas and gas hydrates, have not been yet assessed even though are strongly related to hydrocarbon occurrence worldwide (Caspian Sea, Gulf of Mexico, Western African Basin, Trinidad-Tobago, the Nile Cone. For this reason, the source rock potential of the Late Miocene lacustrine deposits on a backstop basin of the Hellenic Trench System (Messara Basin, Crete, Greece, was studied. The obtained pyrolysis data indicate that the containing organic matter is present in sufficient abundance and with good enough quality to be regarded as potential source rocks. The observed type III kerogen suggests gas generation potential. Although indications of higher thermal evolution occur the studied rocks suggest low maturation levels. The biogenic gas seeps in the studied research well further demonstrate the regional gas generation potential.

Implications of Eocene-age Philippine Sea and forearc basalts for initiation and early history of the Izu-Bonin-Mariana arc

Science.gov (United States)

Yogodzinski, Gene M.; Bizimis, Michael; Hickey-Vargas, Rosemary; McCarthy, Anders; Hocking, Benjamin D.; Savov, Ivan P.; Ishizuka, Osamu; Arculus, Richard

2018-05-01

Whole-rock isotope ratio (Hf, Nd, Pb, Sr) and trace element data for basement rocks at ocean drilling Sites U1438, 1201 and 447 immediately west of the KPR (Kyushu-Palau Ridge) are compared to those of FAB (forearc basalts) previously interpreted to be the initial products of IBM subduction volcanism. West-of-KPR basement basalts (drill sites U1438, 1201, 447) and FAB occupy the same Hf-Nd and Pb-Pb isotopic space and share distinctive source characteristics with εHf mostly > 16.5 and up to εHf = 19.8, which is more radiogenic than most Indian mid-ocean ridge basalts (MORB). Lead isotopic ratios are depleted, with 206Pb/204Pb = 17.8-18.8 accompanying relatively high 208Pb/204Pb, indicating an Indian-MORB source unlike that of West Philippine Basin plume basalts. Some Sr isotopes show affects of seawater alteration, but samples with 87Sr/86Sr 8.0 appear to preserve magmatic compositions and also indicate a common source for west-of-KPR basement and FAB. Trace element ratios resistant to seawater alteration (La/Yb, Lu/Hf, Zr/Nb, Sm/Nd) in west-of-KPR basement are generally more depleted than normal MORB and so also appear similar to FAB. At Site U1438, only andesite sills intruding sedimentary rocks overlying the basement have subduction-influenced geochemical characteristics (εNd ∼ 6.6, εHf ∼ 13.8, La/Yb > 2.5, Nd/Hf ∼ 9). The key characteristic that unites drill site basement rocks west of KPR and FAB is the nature of their source, which is more depleted in lithophile trace elements than average MORB but with Hf, Nd, and Pb isotope ratios that are common in MORB. The lithophile element-depleted nature of FAB has been linked to initiation of IBM subduction in the Eocene, but Sm-Nd model ages and errorchron relationships in Site U1438 basement indicate that the depleted character of the rocks is a regional characteristic that was produced well prior to the time of subduction initiation and persists today in the source of modern IBM arc volcanic rocks with

Strong-motion characteristics and source process during the Suruga Bay earthquake in 2009 through observed records on rock sites

International Nuclear Information System (INIS)

Shiba, Yoshiaki; Sato, Hiroaki; Kuriyama, Masayuki

2010-01-01

On 11 August 2009, a moderate earthquake of M 6.5 occurred in the Suruga Bay region, south of Shizuoka prefecture. During this event, JMA Seismic Intensity reached 6 lower in several cities around the hypocenter, and at Hamaoka nuclear power plant of Chubu Electric Power reactors were automatically shutdown due to large ground motions. Though the epicenter is located at the eastern edge of source area for the assumed great Tokai earthquake of M 8, this event is classified into the intra-plate (intra-slab) earthquake, due to its focal depth lower than that of the plate boundary and fault geometry supposed from the moment tensor solution. Dense strong-motion observation network has been deployed mainly on the rock outcrops by our institute around the source area, and the waveform data of the main shock and several aftershocks were obtained at 13 stations within 100 km from the hypocenter. The observed peak ground motions and velocity response spectral amplitudes are both obviously larger than the empirical attenuation relations derived from the inland and plate-boundary earthquake data, which displays the characteristics of the intra-slab earthquake faulting. Estimated acceleration source spectra of the main shock also exhibit the short period level about 1.7 times larger than the average of those for past events, and it corresponds with the additional term in the attenuation curve of the peak ground acceleration for the intra-plate earthquake. Detailed source process of the main shock is inferred using the inversion technique. The initial source model is assumed to be composed of two distinct fault planes according to the minute aftershock distribution. Estimated source model shows that large slip occurred near the hypocenter and at the boundary region between two fault planes where the rupture transfers from primary to secondary fault. Furthermore the broadband source inversion using velocity motions in the frequency up to 5 Hz demonstrates the high effective

A radiation protection initiative to map old radium sources

International Nuclear Information System (INIS)

Risica, S.; Grisanti, G.; Masi, R.; Melfi, A.

2008-01-01

Due to a legacy of past events, the Technology and Health Department of the Instituto Superiore di Sanita (ISS) has preserved an old, large archive of the allocation of radium sources in public hospitals. These sources were purchased by the Ministry of Interior first, then by the Ministry of Health, and provided to hospitals for cancer brachytherapy. After a retrieval initiative - organised in the 1980's, but discontinued some years later owing to the saturation of the temporary storage site - a considerable number of these sources remained in the hospitals. As a result of an incomplete transfer of the retrieval data, some events connected with the second world war, and the decision of some hospitals to dispose directly of their sources without informing the ISS, the archive was not completed and a series of initiatives were undertaken by the ISS to update it. On the other hand, following the concerns that arose after September 11th, 2001 about the possible criminal use of radioactive sources, the Carabinieri Environmental Care Command (CCTA) were required by the Minister of Environment to carry out a thorough investigation into all possible nuclear sources and waste in the country. Special attention was devoted to radium sources because of the high risk their loss or theft entails. For this reason, in 2004, the CCTA made an agreement with the ISS to acquire a final, updated picture of the distribution of these radium sources. In March 2007 a comprehensive report on this collaborative action and its conclusions was officially sent to both the Ministry of Health and the Ministry of the Environment. The paper describes the involvement of these two bodies in the issue, their collaborative action and the most relevant results. (author)

Water sources for cyanobacteria below desert rocks in the Negev Desert determined by conductivity

Directory of Open Access Journals (Sweden)

Christopher P. McKay

2016-04-01

Full Text Available We present year round meteorological and conductivity measurements of colonized hypolithic rocks in the Arava Valley, Negev Desert, Israel. The data indicate that while dew is common in the Negev it is not an important source of moisture for hypolithic organisms at this site. The dominance of cyanobacteria in the hypolithic community is consistent with predictions that cyanobacteria are confined to habitats supplied by rain. To monitor the presence of liquid water under the small Negev rocks we developed and tested a simple field conductivity system based on two wires placed about 0.5 cm apart. Based on 21 replicates recorded for one year in the Negev we conclude that in natural rains (0.25 mm to 6 mm the variability between sensor readings is between 20 and 60% decreasing with increasing rain amount. We conclude that the simple small electrical conductivity system described here can be used effectively to monitor liquid water levels in lithic habitats. However, the natural variability of these sensors indicates that several replicates should be deployed. The results and method presented have use in arid desert reclamation programs.

Convergent evidence for widespread rock nitrogen sources in Earth’s surface environment

Science.gov (United States)

Houlton, B. Z.; Morford, S. L.; Dahlgren, R. A.

2018-04-01

Nitrogen availability is a pivotal control on terrestrial carbon sequestration and global climate change. Historical and contemporary views assume that nitrogen enters Earth’s land-surface ecosystems from the atmosphere. Here we demonstrate that bedrock is a nitrogen source that rivals atmospheric nitrogen inputs across major sectors of the global terrestrial environment. Evidence drawn from the planet’s nitrogen balance, geochemical proxies, and our spatial weathering model reveal that ~19 to 31 teragrams of nitrogen are mobilized from near-surface rocks annually. About 11 to 18 teragrams of this nitrogen are chemically weathered in situ, thereby increasing the unmanaged (preindustrial) terrestrial nitrogen balance from 8 to 26%. These findings provide a global perspective to reconcile Earth’s nitrogen budget, with implications for nutrient-driven controls over the terrestrial carbon sink.

Waste-rock interactions and bedrock reactions

International Nuclear Information System (INIS)

White, W.B.

1977-01-01

The experimental program is designed to discover possible reactions between shale repository rocks and radioactive wastes. The canister can be regarded in three ways: (a) As a source of heat that modifies the mineralogy and therefore the physical properties of the surrounding rock (dry heat). (b) As a source of heat that activates reactions between minerals in the surrounding rock and slowly percolating ground water. (c) As a source of reaction materials of different composition from the surrounding rock and which therefore may react to form completely new ''minerals'' in a contact aureole around the canister. The matrix of interactions contains two composition axes. The waste compositions are defined by the various prototype waste forms usually investigated: glass, calcine, ''spent fuel'' and the ceramic supercalcine. The temperatures and pressures at which these reactions take place must be investigated. Thus each node on the ''wiring diagram'' is itself a matrix of experiments in which the T and to some extent P are varied. Experiments at higher pressure and temperature allow reactions to take place on a laboratory time scale and thus identify what could happen. These reactions are then followed downward in temperature to determine both phase boundaries and kinetic cut-offs below which equilibrium cannot be achieved on a laboratory time scale

Investigation on the Vibration Effect of Shock Wave in Rock Burst by In Situ Microseismic Monitoring

Directory of Open Access Journals (Sweden)

Mingshi Gao

2018-01-01

Full Text Available Rock burst is a physical explosion associated with enormous damage at a short time. Due to the complicity of mechanics of rock burst in coal mine roadway, the direct use of traditional investigation method applied in tunnel is inappropriate since the components of surrounding rock are much more complex in underground than that of tunnel. In addition, the reliability of the results obtained through these methods (i.e., physical simulation, theoretical analysis, and monitoring in filed application is still not certain with complex geological conditions. Against this background, present experimental study was first ever conducted at initial site to evaluate the effect of shock wave during the rock burst. TDS-6 microseismic monitoring system was set up in situ to evaluate the propagation of shock wave resulting in microexplosions of roadway surrounding rock. Various parameters including the distance of epicentre and the characteristic of response have been investigated. Detailed test results revealed that (1 the shock wave attenuated exponentially with the increase of the distance to seismic source according to the equation of E=E0e-ηl; particularly, the amplitude decreased significantly after being 20 m apart from explosive resource and then became very weak after being 30 m apart from the seismic source; (2 the response mechanics are characteristic with large scatter based on the real location of surrounding rock despite being at the same section. That is, the surrounding rock of floor experienced serious damage, followed by ribs, the roof, and the humeral angles. This in situ experimental study also demonstrated that microseismic monitoring system can be effectively used in rock burst through careful setup and data investigation. The proposed in situ monitoring method has provided a new way to predict rock burst due to its simple instalment procedure associated with direct and reasonable experimental results.

Compact rock material gas permeability properties

Energy Technology Data Exchange (ETDEWEB)

Wang, Huanling, E-mail: whl_hm@163.com [Key Laboratory of Coastal Disaster and Defence, Ministry of Education, Hohai University, Nanjing 210098 (China); LML, University of Lille, Cite Scientifique, 59655 Villeneuve d’Ascq (France); Xu, Weiya; Zuo, Jing [Institutes of Geotechnical Engineering, Hohai University, Nanjing 210098 (China)

2014-09-15

Natural compact rocks, such as sandstone, granite, and rock salt, are the main materials and geological environment for storing underground oil, gas, CO{sub 2,} shale gas, and radioactive waste because they have extremely low permeabilities and high mechanical strengths. Using the inert gas argon as the fluid medium, the stress-dependent permeability and porosity of monzonitic granite and granite gneiss from an underground oil storage depot were measured using a permeability and porosity measurement system. Based on the test results, models for describing the relationships among the permeability, porosity, and confining pressure of rock specimens were analyzed and are discussed. A power law is suggested to describe the relationship between the stress-dependent porosity and permeability; for the monzonitic granite and granite gneiss (for monzonitic granite (A-2), the initial porosity is approximately 4.05%, and the permeability is approximately 10{sup −19} m{sup 2}; for the granite gneiss (B-2), the initial porosity is approximately 7.09%, the permeability is approximately 10{sup −17} m{sup 2}; and the porosity-sensitivity exponents that link porosity and permeability are 0.98 and 3.11, respectively). Compared with moderate-porosity and high-porosity rocks, for which φ > 15%, low-porosity rock permeability has a relatively lower sensitivity to stress, but the porosity is more sensitive to stress, and different types of rocks show similar trends. From the test results, it can be inferred that the test rock specimens’ permeability evolution is related to the relative particle movements and microcrack closure.

Potential GTCC LLW sealed radiation source recycle initiatives

International Nuclear Information System (INIS)

Fischer, D.

1992-04-01

This report suggests 11 actions that have the potential to facilitate the recycling (reuse or radionuclide) of surplus commercial sealed radiation sources that would otherwise be disposed of as greater-than-Class C low-level radioactive waste. The suggestions serve as a basis for further investigation and discussion between the Department of Energy, Nuclear Regulatory Commission, Agreement States, and the commercial sector. Information is also given that describes sealed sources, how they are used, and problems associated with recycling, including legal concerns. To illustrate the nationwide recycling potential, Appendix A gives the estimated quantity and application information for sealed sources that would qualify for disposal in commercial facilities if not recycle. The report recommends that the Department of Energy initiate the organization of a forum to explore the suggested actions and other recycling possibilities

Convergent evidence for widespread rock nitrogen sources in Earth's surface environment.

Science.gov (United States)

Houlton, B Z; Morford, S L; Dahlgren, R A

2018-04-06

Nitrogen availability is a pivotal control on terrestrial carbon sequestration and global climate change. Historical and contemporary views assume that nitrogen enters Earth's land-surface ecosystems from the atmosphere. Here we demonstrate that bedrock is a nitrogen source that rivals atmospheric nitrogen inputs across major sectors of the global terrestrial environment. Evidence drawn from the planet's nitrogen balance, geochemical proxies, and our spatial weathering model reveal that ~19 to 31 teragrams of nitrogen are mobilized from near-surface rocks annually. About 11 to 18 teragrams of this nitrogen are chemically weathered in situ, thereby increasing the unmanaged (preindustrial) terrestrial nitrogen balance from 8 to 26%. These findings provide a global perspective to reconcile Earth's nitrogen budget, with implications for nutrient-driven controls over the terrestrial carbon sink. Copyright © 2018 The Authors, some rights reserved; exclusive licensee American Association for the Advancement of Science. No claim to original U.S. Government Works.

Research on Relationship Between Parameters Correlation of Acoustic Emission and Rock Failure

Directory of Open Access Journals (Sweden)

Duan Dong

2014-12-01

Full Text Available Analyzes that granite AE signal parameters under uniaxial loading by that way of Pearson linear correlation, research that correlation of characterization parameters within that separate group with various characteristics, and analyzes that relationship between each parameter and destruction. This study shows that: impact, events and ringing are mainly used to describe the damage degree of rock, amplitude characteristics, time characteristics and frequency characteristics are mainly used for acoustic emission source properties, and energy characteristics can not only be used to describe the damage degree of rock, but also be used to analyze the acoustic emission source. That ringing counts are highly interrelated with energy, intensity, duration, RMS and ASL have high correlation, a high correlation is in the three parameters of the energy characteristics, and there is a higher correlation between the two parameters of the timing characteristics. The correlation between the parameters of frequency is very low, and the acoustic emission parameters can't be replaced for each other in analysis, which need separate analysis. Characteristics of ringing and energy can be a very good description of failure, but failure precursors can't be quantized. However, the amplitude, RMS, ASL, can quantify characterization of that precursor of failure, such as the effective voltage value 0.7 V as the precursor of destruction, the emergence of amplitude exceeding 95 dB as that destructive precursor. The relationship between the timing characteristics and damage is not obvious, so you can't use those parameters analysis that fracture of rocks. But those parameters can be used to describe AE source characteristics. The peak frequency, inverse frequency and the center frequency can't reflect AE source characteristics, and that average frequency and initial frequency can reflect AE source characteristics.

Clay club initiative: self-healing of fractures in clay-rich host rocks

International Nuclear Information System (INIS)

Horseman, S.T.; Cuss, R.J.; Reeves, H.J.

2004-01-01

The capacity of fractures in argillaceous rocks to self-heal (or become, with the passage of time, less conductive to groundwater) is often cited as a primary factor favouring the choice of such materials as host rocks for deep disposal. The underlying processes which contribute to self-healing can be broadly subdivided into: (a) mechanical and hydro-mechanical processes linked to the change in the stress field, movement of pore water, swelling, softening, plastic deformation and creep, and (b) geochemical processes linked to chemical alterations, transport in aqueous solution and the precipitation of minerals. Since chemical alteration can cause profound changes to the mechanical properties of argillaceous rocks, it is often difficult to draw a firm line between these two subdivisions. Based on the deliberations of the recent Cluster Conference in Luxembourg, there would appear to be some support for the use of the term 'self-sealing' for processes affecting fracture conductivity in argillaceous rock that are largely mechanical or hydro-mechanical in their origin. There are four main areas in which the self-healing capacity of the host rock becomes relevant to repository design and performance assessment: - potential for radionuclide transport within the excavation damage zone (EDZ); - design and performance of repository sealing systems; - potential impact of gas migration; - long-term performance considering erosional unloading, seismicity and fault reactivation. The presence of an EDZ is acknowledged to be a particularly important issue in performance assessment. Interconnection of fractures in the EDZ could lead to the development of a preferential flow path extending along the emplacement holes, access tunnels and shafts of a repository towards overlying aquifers and the biosphere. In the preliminary French Safety Analyses, for example, the treatment of scenarios relating to early seal failure have highlighted the hydraulic role of the damaged zone as a

A heat source probe for measuring thermal conductivity in waste rock dumps

International Nuclear Information System (INIS)

Blackford, M.G.; Harries, J.R.

1985-10-01

The development and use of a heat source probe to measure the thermal conductivity of the material in a waste rock dump is described. The probe releases heat at a constant rate into the surrounding material and the resulting temperature rise is inversely related to the thermal conductivity. The probe was designed for use in holes in the dump which are lined with 50 mm i.d. polyethylene liners. The poor thermal contact between the probe and the liner and the unknown conductivity of the backfill material around the liner necessitated long heating and cooling times (>10 hours) to ensure that the thermal conductivity of the dump material was being measured. Temperature data acquired in the field were analysed by comparing them with temperatures calculated using a two-dimensional cylindrical model of the probe and surrounding material, and the heat transfer code HEATRAN

Constraints on equivalent elastic source models from near-source data

International Nuclear Information System (INIS)

Stump, B.

1993-01-01

A phenomenological based seismic source model is important in quantifying the important physical processes that affect the observed seismic radiation in the linear-elastic regime. Representations such as these were used to assess yield effects on seismic waves under a Threshold Test Ban Treaty and to help transport seismic coupling experience at one test site to another. These same characterizations in a non-proliferation environment find applications in understanding the generation of the different types of body and surface waves from nuclear explosions, single chemical explosions, arrays of chemical explosions used in mining, rock bursts and earthquakes. Seismologists typically begin with an equivalent elastic representation of the source which when convolved with the propagation path effects produces a seismogram. The Representation Theorem replaces the true source with an equivalent set of body forces, boundary conditions or initial conditions. An extension of this representation shows the equivalence of the body forces, boundary conditions and initial conditions and replaces the source with a set of force moments, the first degree moment tensor for a point source representation. The difficulty with this formulation, which can completely describe the observed waveforms when the propagation path effects are known, is in the physical interpretation of the actual physical processes acting in the source volume. Observational data from within the source region, where processes are often nonlinear, linked to numerical models of the important physical processes in this region are critical to a unique physical understanding of the equivalent elastic source function

Bioremediation in fractured rock: 2. Mobilization of chloroethene compounds from the rock matrix

Science.gov (United States)

Shapiro, Allen M.; Tiedeman, Claire; Imbrigiotta, Thomas; Goode, Daniel J.; Hsieh, Paul A.; Lacombe, Pierre; DeFlaun, Mary F.; Drew, Scott R.; Curtis, Gary P.

2018-01-01

A mass balance is formulated to evaluate the mobilization of chlorinated ethene compounds (CE) from the rock matrix of a fractured mudstone aquifer under pre- and postbioremediation conditions. The analysis relies on a sparse number of monitoring locations and is constrained by a detailed description of the groundwater flow regime. Groundwater flow modeling developed under the site characterization identified groundwater fluxes to formulate the CE mass balance in the rock volume exposed to the injected remediation amendments. Differences in the CE fluxes into and out of the rock volume identify the total CE mobilized from diffusion, desorption, and nonaqueous phase liquid dissolution under pre- and postinjection conditions. The initial CE mass in the rock matrix prior to remediation is estimated using analyses of CE in rock core. The CE mass mobilized per year under preinjection conditions is small relative to the total CE mass in the rock, indicating that current pump-and-treat and natural attenuation conditions are likely to require hundreds of years to achieve groundwater concentrations that meet regulatory guidelines. The postinjection CE mobilization rate increased by approximately an order of magnitude over the 5 years of monitoring after the amendment injection. This rate is likely to decrease and additional remediation applications over several decades would still be needed to reduce CE mass in the rock matrix to levels where groundwater concentrations in fractures achieve regulatory standards.

Recovering the source and initial value simultaneously in a parabolic equation

International Nuclear Information System (INIS)

Zheng, Guang-Hui; Wei, Ting

2014-01-01

In this paper, we consider an inverse problem to simultaneously reconstruct the source term and initial data associated with a parabolic equation based on the additional temperature data at a terminal time t = T and the temperature data on an accessible part of a boundary. The conditional stability and uniqueness of the inverse problem are established. We apply a variational regularization method to recover the source and initial value. The existence, uniqueness and stability of the minimizer of the corresponding variational problem are obtained. Taking the minimizer as a regularized solution for the inverse problem, under an a priori and an a posteriori parameter choice rule, the convergence rates of the regularized solution under a source condition are also given. Furthermore, the source condition is characterized by an optimal control approach. Finally, we use a conjugate gradient method and a stopping criterion given by Morozov's discrepancy principle to solve the variational problem. Numerical experiments are provided to demonstrate the feasibility of the method. (papers)

Heat production in granitic rocks

DEFF Research Database (Denmark)

Artemieva, Irina; Thybo, Hans; Jakobsen, Kiki

2017-01-01

Granitic rocks play special role in the dynamics and evolution of the Earth and its thermal regime. First, their compositional variability, reflected in the distribution of concentrations of radiogenic elements, provides constraints on global differentiation processes and large scale planetary...... evolution, where emplacement of granites is considered a particularly important process for the formation of continental crust. Second, heat production by radioactive decay is among the main heat sources in the Earth. Therefore knowledge of heat production in granitic rocks is pivotal for thermal modelling...... of the continental lithosphere, given that most radiogenic elements are concentrated in granitic rocks of the upper continental crust whereas heat production in rocks of the lower crust and lithospheric mantle is negligible. We present and analyze a new global database GRANITE2017 (with about 500 entries...

Petrochemical and Sr-Nd isotope investigations of Cretaceous intrusive rocks and their enclaves in the Togouchi-Yoshiwa district, northwest Hiroshima prefecture, SW Japan

International Nuclear Information System (INIS)

Ishioka, Jun; Iizumi, Shigeru

2003-01-01

Petrographic, petrochemical and Sr-Nd isotopic data are presented for granitoids and microdioritic enclaves from two Cretaceous stocks (Togouchi granodiorite and Tateiwayama granite porphyry) from the Togouchi-Yoshiwa district, northwest Hiroshima prefecture, SW Japan. The data are used to examine the genetic relationships between the microdioritic enclaves and their granitoid hosts. The granodiorite, granite porphyry and the microdioritic enclaves are all calc-alkaline in nature, and belong to the I-type ilmenite series. The Togouchi graniodiorite has a Rb-Sr whole rock isochron age of 85.6±4.7 Ma with an initial Sr isotope ratio (SrI) of 0.70634±0.00012 (2σ). The Tateiwayama granite porphyry has a slightly younger Rb-Sr whole isochron age (77.4±3.1 Ma) but similar SrI of 0.70653±0.00015, suggesting that both stocks may have been derived from the same source. Despite diverse whole rock chemistry, the microdioritic enclaves in the respective intrusives have quite similar initial Sr and Nd isotope ratios, suggesting that they formed by fractional crystallization of a single magma, and also that the source of the enclaves in both intrusives had similar geochemical characteristics. In both stocks, however, the enclaves have distinctly lower initial Sr isotope ratios than their respective host rocks, indicating that they were derived from a different source than their hosts. In view of the geochemical and Sr-Nd isotope data, we infer that the enclave magmas were derived from a similar LILE- and LREE-enriched source to that of the Cretaceous basalts and gabbroic-dioritic rocks that are sporadically distributed in SW Japan. Such mafic to intermediate magmas were probably derived from the upper mantle, and transferred both heat and material to the lower crust, thus producing granitic magmas by partial melting. Successive mafic magmas or their differentiates could then have been injected into the granitic magma chamber, trapped and quenched, resulting in the formation

7-GeV advanced photon source beamline initiative: Conceptual design report

International Nuclear Information System (INIS)

1993-05-01

The DOE is building a new generation 6-7 GeV Synchrotron Radiation Source known as the Advanced Photon Source (APS) at Argonne National Laboratory. This facility, to be completed in FY 1996, can provide 70 x-ray sources of unprecedented brightness to meet the research needs of virtually all scientific disciplines and numerous technologies. The technological research capability of the APS in the areas of energy, communications and health will enable a new partnership between the DOE and US industry. Current funding for the APS will complete the current phase of construction so that scientists can begin their applications in FY 1996. Comprehensive utilization of the unique properties of APS beams will enable cutting-edge research not currently possible. It is now appropriate to plan to construct additional radiation sources and beamline standard components to meet the excess demands of the APS users. In this APS Beamline Initiative, 2.5-m-long insertion-device x-ray sources will be built on four straight sections of the APS storage ring, and an additional four bending-magnet sources will also be put in use. The front ends for these eight x-ray sources will be built to contain and safeguard access to these bright x-ray beams. In addition, funds will be provided to build standard beamline components to meet scientific and technological research demands of the Collaborative Access Teams. The Conceptual Design Report (CDR) for the APS Beamline Initiative describes the scope of all the above technical and conventional construction and provides a detailed cost and schedule for these activities. The document also describes the preconstruction R ampersand D plans for the Beamline Initiative activities and provides the cost estimates for the required R ampersand D

Thermally induced rock stress increment and rock reinforcement response

International Nuclear Information System (INIS)

Hakala, M.; Stroem, J.; Nujiten, G.; Uotinen, L.; Siren, T.; Suikkanen, J.

2014-07-01

deformation zones is included. The main conclusion is that, despite deep reaching damage potential, in all the load cases studied the currently designed and used reinforcement types and configurations (rock bolts, shotcrete) are capable of handling the dead weight of the damaged rock should this occur, with damage occurring on the shotcrete liner. The long term safety and stability of the repository during its lifetime can be guaranteed by perceiving the reinforcement strategy in two stages. Firstly, by installing the rock reinforcement to sustain the initial stresses and short term increases from the start of deposition with a monitoring programme in place. Secondly, by installing additional reinforcement, if found necessary through monitoring and observation of the underground facilities. In this way, the effect of any time dependent rock stress increase affecting the reinforcement structures can be observed, in addition to creep based damage, thus providing a better level of safety than a single stage design. (orig.)

Thermally induced rock stress increment and rock reinforcement response

Energy Technology Data Exchange (ETDEWEB)

Hakala, M. [KMS Hakala Oy, Nokia (Finland); Stroem, J.; Nujiten, G.; Uotinen, L. [Rockplan, Helsinki (Finland); Siren, T.; Suikkanen, J.

2014-07-15

brittle deformation zones is included. The main conclusion is that, despite deep reaching damage potential, in all the load cases studied the currently designed and used reinforcement types and configurations (rock bolts, shotcrete) are capable of handling the dead weight of the damaged rock should this occur, with damage occurring on the shotcrete liner. The long term safety and stability of the repository during its lifetime can be guaranteed by perceiving the reinforcement strategy in two stages. Firstly, by installing the rock reinforcement to sustain the initial stresses and short term increases from the start of deposition with a monitoring programme in place. Secondly, by installing additional reinforcement, if found necessary through monitoring and observation of the underground facilities. In this way, the effect of any time dependent rock stress increase affecting the reinforcement structures can be observed, in addition to creep based damage, thus providing a better level of safety than a single stage design. (orig.)

Silurian and Devonian source rocks and crude oils from the western part of Libya: Organic geochemistry, palynology and carbon stratigraphy

NARCIS (Netherlands)

Elkelani, Mohamed M.A.

2015-01-01

The Early Silurian “hot” shales and Late Devonian black shales are major regional oil and gas source rocks in North Africa. Their deposition probably played a major role in global carbon cycling in general because of the large areas of the ocean affected. Comparing the Libyan δ13C record with

Thermophysical properties of rocks: a perspective on data needs, sources and accuracy

International Nuclear Information System (INIS)

Stephens, H.P.; Sinnock, S.

1979-01-01

Recent emphasis on research in geologic isolation of nuclear wastes and geoenergy resource development has created a renewed demand for engineering thermophysical property data for rocks and other geologic materials at elevated pressures and temperatures. In contrast to fabricated engineering materials, with properties which can be specified, rocks used in engineering design are complex, naturally occurring materials having properties which must be characterized, rather than specified, for engineering studies. Much difficulty in measuring, reporting, and using thermophysical properties of rocks results from (1) rock inhomogeneity and anisotropy on both microscopic and macroscopic scales; (2) inclusion of pore fluids, such as water; and (3) measurement of laboratory properties under conditions quite different from those of in situ material. Because measurements on in situ materials are scarce, many analyses must depend on extrapolated values of uncertain accuracy. A survey of thermophysical property data available for geologic thermal transport studies indicates that caution must be taken to effectively match data abstracted from the literature with project objectives

Relationship of oil seep in Kudat Peninsula with surrounding rocks based on geochemical analysis

Science.gov (United States)

Izzati Azman, Nurul; Nur Fathiyah Jamaludin, Siti

2017-10-01

This study aims to investigate the relation of oil seepage at Sikuati area with the structural and petroleum system of Kudat Peninsula. The abundance of highly carbonaceous rocks with presence of lamination in the Sikuati Member outcrop at Kudat Peninsula may give an idea on the presence of oil seepage in this area. A detailed geochemical analysis of source rock sample and oil seepage from Sikuati area was carried out for their characterization and correlation. Hydrocarbon propectivity of Sikuati Member source rock is poor to good with Total Organic Carbon (TOC) value of 0.11% to 1.48%. and also categorized as immature to early mature oil window with Vitrinite Reflectance (VRo) value of 0.43% to 0.50 %Ro. Based on biomarker distribution, from Gas Chromatography (GC) and Gas Chromatography-Mass Spectrometry (GC-MS) analysis, source rock sample shows Pr/Ph, CPI and WI of 2.22 to 2.68, 2.17 to 2.19 and 2.46 to 2.74 respectively indicates the source rock is immature and coming from terrestrial environment. The source rock might be rich in carbonaceous material organic matter resulting from planktonic/bacterial activity which occurs at fluvial to fluvio-deltaic environment. Overall, the source rock from outcrop level of Kudat Peninsula is moderately prolific in term of prospectivity and maturity. However, as go far deeper beneath the surface, we can expect more activity of mature source rock that generate and expulse hydrocarbon from the subsurface then migrating through deep-seated fault beneath the Sikuati area.

Bioremediation in Fractured Rock: 2. Mobilization of Chloroethene Compounds from the Rock Matrix.

Science.gov (United States)

Shapiro, Allen M; Tiedeman, Claire R; Imbrigiotta, Thomas E; Goode, Daniel J; Hsieh, Paul A; Lacombe, Pierre J; DeFlaun, Mary F; Drew, Scott R; Curtis, Gary P

2018-03-01

A mass balance is formulated to evaluate the mobilization of chlorinated ethene compounds (CE) from the rock matrix of a fractured mudstone aquifer under pre- and postbioremediation conditions. The analysis relies on a sparse number of monitoring locations and is constrained by a detailed description of the groundwater flow regime. Groundwater flow modeling developed under the site characterization identified groundwater fluxes to formulate the CE mass balance in the rock volume exposed to the injected remediation amendments. Differences in the CE fluxes into and out of the rock volume identify the total CE mobilized from diffusion, desorption, and nonaqueous phase liquid dissolution under pre- and postinjection conditions. The initial CE mass in the rock matrix prior to remediation is estimated using analyses of CE in rock core. The CE mass mobilized per year under preinjection conditions is small relative to the total CE mass in the rock, indicating that current pump-and-treat and natural attenuation conditions are likely to require hundreds of years to achieve groundwater concentrations that meet regulatory guidelines. The postinjection CE mobilization rate increased by approximately an order of magnitude over the 5 years of monitoring after the amendment injection. This rate is likely to decrease and additional remediation applications over several decades would still be needed to reduce CE mass in the rock matrix to levels where groundwater concentrations in fractures achieve regulatory standards. © 2017, National Ground Water Association.

143Nd/144Nd and 87Sr/86Sr isotope ratio variations in magmatic rocks of Aleutian island arc as regard to the problem of their petrogenesis

International Nuclear Information System (INIS)

Zhuravlev, D.Z.; Chernyshev, I.V.; Tsvetkov, A.A.; Borsuk, A.M.; Agapova, A.A.; Serdyuk, N.I.

1983-01-01

The results of precision measurement of isotope composition of neodymium in rocks of Pre-Quaternary magmatic formations of the Aleutian island arc (AIA) (Commander Islands). It has been found summing the Nd and Sr analysis results in AIA magmatic rocks that AIA magmatic melts are of mantle origin. The AIA magma source the full its length off and for all the history of geological development remained isotopically homogeneousm Crust contamination of magmatic melts played a significant role only in the initial and early stages of the AIA development, in the later and conclusive stages this process has been sharply reduced. Sedimentary material practically did not take part in the magmaproduction process at the initial stage of the AIA development, it is hardly probable that its role increased at the later stages. The cause of important 87 Sr/ 86 Sr ratio variations in the rocks of one AIA petrographic type is the propylitization process with participation of sea water. Variance of 87 Sr/ 86 Sr ratios without taking into account other isotope systems data is not an indisputable proof of magma source heterogeneity

Effects of confinement on rock mass modulus: A synthetic rock mass modelling (SRM study

Directory of Open Access Journals (Sweden)

I. Vazaios

2018-06-01

Full Text Available The main objective of this paper is to examine the influence of the applied confining stress on the rock mass modulus of moderately jointed rocks (well interlocked undisturbed rock mass with blocks formed by three or less intersecting joints. A synthetic rock mass modelling (SRM approach is employed to determine the mechanical properties of the rock mass. In this approach, the intact body of rock is represented by the discrete element method (DEM-Voronoi grains with the ability of simulating the initiation and propagation of microcracks within the intact part of the model. The geometry of the pre-existing joints is generated by employing discrete fracture network (DFN modelling based on field joint data collected from the Brockville Tunnel using LiDAR scanning. The geometrical characteristics of the simulated joints at a representative sample size are first validated against the field data, and then used to measure the rock quality designation (RQD, joint spacing, areal fracture intensity (P21, and block volumes. These geometrical quantities are used to quantitatively determine a representative range of the geological strength index (GSI. The results show that estimating the GSI using the RQD tends to make a closer estimate of the degree of blockiness that leads to GSI values corresponding to those obtained from direct visual observations of the rock mass conditions in the field. The use of joint spacing and block volume in order to quantify the GSI value range for the studied rock mass suggests a lower range compared to that evaluated in situ. Based on numerical modelling results and laboratory data of rock testing reported in the literature, a semi-empirical equation is proposed that relates the rock mass modulus to confinement as a function of the areal fracture intensity and joint stiffness. Keywords: Synthetic rock mass modelling (SRM, Discrete fracture network (DFN, Rock mass modulus, Geological strength index (GSI, Confinement

The Open Source DataTurbine Initiative: Streaming Data Middleware for Environmental Observing Systems

Science.gov (United States)

Fountain T.; Tilak, S.; Shin, P.; Hubbard, P.; Freudinger, L.

2009-01-01

The Open Source DataTurbine Initiative is an international community of scientists and engineers sharing a common interest in real-time streaming data middleware and applications. The technology base of the OSDT Initiative is the DataTurbine open source middleware. Key applications of DataTurbine include coral reef monitoring, lake monitoring and limnology, biodiversity and animal tracking, structural health monitoring and earthquake engineering, airborne environmental monitoring, and environmental sustainability. DataTurbine software emerged as a commercial product in the 1990 s from collaborations between NASA and private industry. In October 2007, a grant from the USA National Science Foundation (NSF) Office of Cyberinfrastructure allowed us to transition DataTurbine from a proprietary software product into an open source software initiative. This paper describes the DataTurbine software and highlights key applications in environmental monitoring.

Growing Pebbles and Conceptual Prisms - Understanding the Source of Student Misconceptions about Rock Formation.

Science.gov (United States)

Kusnick, Judi

2002-01-01

Analyzes narrative essays--stories of rock formation--written by pre-service elementary school teachers. Reports startling misconceptions among preservice teachers on pebbles that grow, human involvement in rock formation, and sedimentary rocks forming as puddles as dry up, even though these students had completed a college level course on Earth…

Initial response of a rock penetrator

International Nuclear Information System (INIS)

Longcope, D.B.; Grady, D.E.

1977-12-01

An analysis based on elastic rod theory is given for the early-time axisymmetric response of pointed penetrators. Results of measurements by laser interferometry of the back surface particle velocity of laboratory scale penetrators impacted by sandstone targets are presented. Values of the initial pressure on the penetrator tip are determined which give good agreement between the analytical and experimental results. These initial tip pressures are found to be approximated by the stress-particle velocity Hugoniot for the target material

Study on performance of a simultaneous spectrometer of ICP emission source for the determination of the major elements in rocks

International Nuclear Information System (INIS)

Vieira, M.D.

1987-01-01

The optimization of operational parameters of a simultaneous spectrometer coupled to an ICP excitation source in order to establish an analytical method for the simultaneous determination of the major elements in rocks is studied. The mutual spectral interferences, calibration curves for the acid and saline matrix and the internal standard method with ytrium are analyzed. (M.J.C.) [pt

I. Some results from a field investigation of thermo-mechanical loading of a rock mass when heaters are emplaced in the rock

International Nuclear Information System (INIS)

Hood, M.

1979-01-01

Results are presented of a field experiment to monitor the response of a rock mass to thermomechanical loading from electrically heated canisters emplaced in the rock at a depth of 340 m. Measurements made to date of temperature, displacement, and stress fields indicate that heat is transferred through the rock mainly by conduction; discontinuities within the rock mass have a minimal effect on the heat flow. Displacements within the rock from thermal expansion are shown to be much less than those predicted by linear thermoelastic theory. A plausible, though not complete, reason for these reduced displacements is the absorption of the initial rock expansions into discontinuities within the rock mass. Difficulties have been experienced in obtaining reliable stress measurement data using borehole deformation gauges to monitor changes in rock stress. Some data have been obtained and are being analyzed. Rock decrepitation in the heater boreholes is discussed

Characterization and obtainment of phosphate rock concentrates of Turmequé, Boyacá

Science.gov (United States)

Zanguña, S. Quijano; Lozano Gómez, L. F.; Pineda Triana, Y.

2017-12-01

The work focuses on the use and exploitation of the mineral concentrates from phosphate rock (PR) coming from mines with a low percentage of phosphorus. The procedure was based on the collection of a source of phosphate rock from the department of Boyacá (municipality of Turmequé), using a randomized design with three replications. The samples were initially milled and sifted using meshes between 140 and 200 US standard, homogenizing them and improving the process of solubility of the phosphorus in the soil. We conduced Z-potential tests, which show that by performing a prior wash on the mineral and maintaining certain concentrations and pH defined, better results are achieved in terms of the buoyancy of the particles in the flotation process. The results obtained from the microflotation tests; both direct and inverse, and the results of chemical composition, with X-Ray Fluorescence (XRF) and X-Ray Diffraction (XRD), before and after the microflotation process, were carried out to obtain of commercial laws grade phosphate rock concentrate, confirm that the protocol used increases by 9% the value of total phosphorus in the collected sample. These concentrates from phosphate rock, could be used in the future for the attainment of simple superphosphate (SSP), with the help of sulphuric acid and ammonium thiosulphate mixtures.

Development of uniform hazard response spectra for rock sites considering line and point sources of earthquakes

International Nuclear Information System (INIS)

Ghosh, A.K.; Kushwaha, H.S.

2001-12-01

Traditionally, the seismic design basis ground motion has been specified by normalised response spectral shapes and peak ground acceleration (PGA). The mean recurrence interval (MRI) used to computed for PGA only. It is shown that the MRI associated with such response spectra are not the same at all frequencies. The present work develops uniform hazard response spectra i.e. spectra having the same MRI at all frequencies for line and point sources of earthquakes by using a large number of strong motion accelerograms recorded on rock sites. Sensitivity of the number of the results to the changes in various parameters has also been presented. This work is an extension of an earlier work for aerial sources of earthquakes. These results will help to determine the seismic hazard at a given site and the associated uncertainities. (author)

Diel cycling of zinc in a stream impacted by acid rock drainage: Initial results from a new in situ Zn analyzer

Science.gov (United States)

Chapin, T.P.; Nimick, D.A.; Gammons, C.H.; Wanty, R.B.

2007-01-01

Recent work has demonstrated that many trace metals undergo dramatic diel (24-h) cycles in near neutral pH streams with metal concentrations reproducibly changing up to 500% during the diel period (Nimick et al., 2003). To examine diel zinc cycles in streams affected by acid rock drainage, we have developed a novel instrument, the Zn-DigiScan, to continuously monitor in situ zinc concentrations in near real-time. Initial results from a 3-day deployment at Fisher Creek, Montana have demonstrated the ability of the Zn-DigiScan to record diel Zn cycling at levels below 100 ??g/l. Longer deployments of this instrument could be used to examine the effects of episodic events such as rainstorms and snowmelt pulses on zinc loading in streams affected by acid rock drainage. ?? Springer Science+Business Media B.V. 2006.

Prediction of Fracture Behavior in Rock and Rock-like Materials Using Discrete Element Models

Science.gov (United States)

Katsaga, T.; Young, P.

2009-05-01

The study of fracture initiation and propagation in heterogeneous materials such as rock and rock-like materials are of principal interest in the field of rock mechanics and rock engineering. It is crucial to study and investigate failure prediction and safety measures in civil and mining structures. Our work offers a practical approach to predict fracture behaviour using discrete element models. In this approach, the microstructures of materials are presented through the combination of clusters of bonded particles with different inter-cluster particle and bond properties, and intra-cluster bond properties. The geometry of clusters is transferred from information available from thin sections, computed tomography (CT) images and other visual presentation of the modeled material using customized AutoCAD built-in dialog- based Visual Basic Application. Exact microstructures of the tested sample, including fractures, faults, inclusions and void spaces can be duplicated in the discrete element models. Although the microstructural fabrics of rocks and rock-like structures may have different scale, fracture formation and propagation through these materials are alike and will follow similar mechanics. Synthetic material provides an excellent condition for validating the modelling approaches, as fracture behaviours are known with the well-defined composite's properties. Calibration of the macro-properties of matrix material and inclusions (aggregates), were followed with the overall mechanical material responses calibration by adjusting the interfacial properties. The discrete element model predicted similar fracture propagation features and path as that of the real sample material. The path of the fractures and matrix-inclusion interaction was compared using computed tomography images. Initiation and fracture formation in the model and real material were compared using Acoustic Emission data. Analysing the temporal and spatial evolution of AE events, collected during the

Initial operation of the CW 8X H- ion source discharge

International Nuclear Information System (INIS)

Smith, H.V. Jr.; Allison, P.; Geisik, C.; Schmitt, D.R.; Schneider, J.D.; Stelzer, J.E.

1993-01-01

A pulsed 8Χ source was built and the H - beam current, emittance, and power efficiency were measured. These results were promising, so a cooled, dc version designed for operation at arc power levels up to 30 kW was built. Testing of the CW 8Χ source discharge is underway. The design dc power loading on the cathode surface is 900 W/cm 2 , considerably higher than achieved in any pervious Penning surface-plasma source (SPS). Thus, the electrode surfaces are cooled with pressurized, hot water. We describe the source and present the initial operating experience and arc test results

Initial operation of the CW 8X H- ion source discharge

International Nuclear Information System (INIS)

Smith, H.V. Jr.; Allison, P.; Geisik, C.; Schmitt, D.R.; Schneider, J.D.; Stelzer, J.E.

1993-01-01

A pulsed 8X source was built and the H - beam current, emittance, and power efficiency were measured. These results were promising, so a cooled, dc version designed for operation at arc power levels up to 30 kW was built. Testing of the CW 8X source discharge is underway. The design dc power loading on the cathode surface is 900 W/cm 2 , considerably higher than achieved in any previous Penning surface-plasma source (SPS). Thus, the electrode surfaces are cooled with pressurized, hot water. The authors describe the source and present the initial operating experience and arc test results

Impact of grain size and rock composition on simulated rock weathering

Science.gov (United States)

Israeli, Yoni; Emmanuel, Simon

2018-05-01

Both chemical and mechanical processes act together to control the weathering rate of rocks. In rocks with micrometer size grains, enhanced dissolution at grain boundaries has been observed to cause the mechanical detachment of particles. However, it remains unclear how important this effect is in rocks with larger grains, and how the overall weathering rate is influenced by the proportion of high- and low-reactivity mineral phases. Here, we use a numerical model to assess the effect of grain size on chemical weathering and chemo-mechanical grain detachment. Our model shows that as grain size increases, the weathering rate initially decreases; however, beyond a critical size no significant decrease in the rate is observed. This transition occurs when the density of reactive boundaries is less than ˜ 20 % of the entire domain. In addition, we examined the weathering rates of rocks containing different proportions of high- and low-reactivity minerals. We found that as the proportion of low-reactivity minerals increases, the weathering rate decreases nonlinearly. These simulations indicate that for all compositions, grain detachment contributes more than 36 % to the overall weathering rate, with a maximum of ˜ 50 % when high- and low-reactivity minerals are equally abundant in the rock. This occurs because selective dissolution of the high-reactivity minerals creates large clusters of low-reactivity minerals, which then become detached. Our results demonstrate that the balance between chemical and mechanical processes can create complex and nonlinear relationships between the weathering rate and lithology.

Gas migration in argillaceous rock

International Nuclear Information System (INIS)

Alonso, E. E.; Olivella, S.

2007-01-01

The intrinsic gas permeability of fractured argillaceous rocks depends on the current structure of micro-cracks and fissures of the rock. They are a consequence of the initial state and the subsequent deformations induced by stress and gas pressure changes. Stresses are also coupled with fluid pressures and, therefore, gas flow and mechanical behaviour are intensely coupled. Laboratory experiments, aimed at determining intrinsic permeability, show the relevant effect of volumetric deformations induced by isotropic, as well as deviatoric stress changes. The relevance, in practice, of the flow-mechanical coupling is illustrated by means of some results obtained during the performance of the drift scale test (DST) in fractured tuff in the Yucca Mountain facility. The technique of embedding discontinuities in continuum thermo-hydro-mechanical elements is capable of reproducing observed features of gas flow migration in clayey rocks. An example is described. It is believed that the developed approach provides a powerful computational procedure to handle complex gas phenomena in clayey rocks. (author)

Fluids in metamorphic rocks

NARCIS (Netherlands)

Touret, J.L.R.

2001-01-01

Basic principles for the study of fluid inclusions in metamorphic rocks are reviewed and illustrated. A major problem relates to the number of inclusions, possibly formed on a wide range of P-T conditions, having also suffered, in most cases, extensive changes after initial trapping. The

Rock burst prevention at steep seam mining

Energy Technology Data Exchange (ETDEWEB)

Efremov, G D

1988-09-01

At steep shield longwalls one method of preventing rock bursts is to avoid sharp angles during working. Stress in coal and rock body that appears when steep seams are worked where rock bursts occur at corners of set-up entries is discussed. The dynamic interaction between gas and rock pressure is assessed. Maintains that in order to avoid rock bursts at these places it is necessary to turn the protruding coal wall by 20-30 degrees towards the coal body to divert the action of shift forces. At the same time the face should also be inclined (by 10-15 degrees) to move the zones of increased stress away from the corner into the coal and rock body. Stress at workings with round cross-sections is 3-4 times lower than at square cross-sections. Recommendations are given that concern shearer loader operation (semi-spherical shape of the face), borehole drilling and water injection. Initial distance of 10-15 m between boreholes is suggested. 3 refs.

Microbial Leaching of Some Valuable Elements From Egyptian Phosphate Rock

International Nuclear Information System (INIS)

Kamal, H.M.; Hassanein, R.A.; Mahdy, H.M.A.; Mahmoud, K.F.; Abouzeid, M.A.

2012-01-01

Four phosphate rock samples representing different phosphate mineralization modes in Egypt were selected from Abu Tartar, Nile valley and Red sea areas. Factors affecting the phosphate rock solubilization and some of the contained valuable elements by Aspergillus niger, Penicillium sp. and Pseudomonas fluorescence, were studied with especial orientation towards the completion of phosphate rock samples solubilization especially die low grade one. Effect of nitrogen source type on leaching efficiency by Aspergillus niger when two nitrogen sources on the phosphate bioleaching efficiency, it is clear that the ammonium chloride is more favorable as nitrogen source than sodium nitrate in the bioleaching of phosphate rocks. When Aspergillus niger was applied under die following conditions: 50 g/1 of sucrose as a carbon source, 0.1 N of ammonium chloride as a nitrogen source, 10 days incubation period, 0.5% solid: liquid ratio for P 2 O 5 and 5% for U and REE and - 270 mesh of grain size. The optimum leaching of P 2 O 5 , U and REE from phosphate rock samples reached (23.27%, 17.4%, 11.4%, respectively), while at -60 mesh they reached to 16.58%, 28.9%, 30.2% respectively. The optimum conditions for the maximal leaching efficiencies of P 2 O 5 , U and REE when applying the Penicillium sp. from the phosphate rock samples were: 100 g/1 of sucrose as a carbon source for P 2 O 5 and U and 10 g/1 for REE, 7,15 and 10 days incubation period for P 2 O 5 , U and REE, respectively, 0.5% solid: liquid ratio for P 2 O 5 and 5% for U and REE. Finally, the application of phosphate rock samples grinded to -270 mesh of grain size for P 2 O 5 and (-60 to -140) for U and REE. The studied leaching efficiency of P 2 O 5 , U and REE gave at -270 mesh 33.66%, 24.3%, 15.9% respectively, while at -60 mesh they gave 33.76%, 26.7%, 17.8% and at -140 mesh gave 31.32%, 27.9%, 17.6%, respectively.The optimum conditions for the P 2 O 5 leaching efficiency when applying the Pseudomonas fluorescence were

Near-Infrared Imaging for Spatial Mapping of Organic Content in Petroleum Source Rocks

Science.gov (United States)

Mehmani, Y.; Burnham, A. K.; Vanden Berg, M. D.; Tchelepi, H.

2017-12-01

Natural gas from unconventional petroleum source rocks (shales) plays a key role in our transition towards sustainable low-carbon energy production. The potential for carbon storage (in adsorbed state) in these formations further aligns with efforts to mitigate climate change. Optimizing production and development from these resources requires knowledge of the hydro-thermo-mechanical properties of the rock, which are often strong functions of organic content. This work demonstrates the potential of near-infrared (NIR) spectral imaging in mapping the spatial distribution of organic content with O(100µm) resolution on cores that can span several hundred feet in depth (Mehmani et al., 2017). We validate our approach for the immature oil shale of the Green River Formation (GRF), USA, and show its applicability potential in other formations. The method is a generalization of a previously developed optical approach specialized to the GRF (Mehmani et al., 2016a). The implications of this work for spatial mapping of hydro-thermo-mechanical properties of excavated cores, in particular thermal conductivity, are discussed (Mehmani et al., 2016b). References:Mehmani, Y., A.K. Burnham, M.D. Vanden Berg, H. Tchelepi, "Quantification of organic content in shales via near-infrared imaging: Green River Formation." Fuel, (2017). Mehmani, Y., A.K. Burnham, M.D. Vanden Berg, F. Gelin, and H. Tchelepi. "Quantification of kerogen content in organic-rich shales from optical photographs." Fuel, (2016a). Mehmani, Y., A.K. Burnham, H. Tchelepi, "From optics to upscaled thermal conductivity: Green River oil shale." Fuel, (2016b).

Evolution Procedure of Multiple Rock Cracks under Seepage Pressure

Directory of Open Access Journals (Sweden)

Taoying Liu

2013-01-01

Full Text Available In practical geotechnical engineering, most of rock masses with multiple cracks exist in water environment. Under such circumstance, these adjacent cracks could interact with each other. Moreover, the seepage pressure, produced by the high water pressure, can change cracks’ status and have an impact on the stress state of fragile rocks. According to the theory of fracture mechanics, this paper discusses the law of crack initiation and the evolution law of stress intensity factor at the tip of a wing crack caused by compression-shear stress and seepage pressure. Subsequently, considering the interaction of the wing cracks and the additional stress caused by rock bridge damage, this paper proposes the intensity factor evolution equation under the combined action of compression-shear stress and seepage pressure. In addition, this paper analyzes the propagation of cracks under different seepage pressure which reveals that the existence of seepage pressure facilitates the wing crack’s growth. The result indicates that the high seepage pressure converts wing crack growth from stable form to unstable form. Meanwhile, based on the criterion and mechanism for crack initiation and propagation, this paper puts forward the mechanical model for different fracture transfixion failure modes of the crag bridge under the combined action of seepage pressure and compression-shear stress. At the last part, this paper, through investigating the flexibility tensor of the rock mass’s initial damage and its damage evolution in terms of jointed rock mass's damage mechanics, deduces the damage evolution equation for the rock mass with multiple cracks under the combined action of compression-shear stress and seepage pressure. The achievement of this investigation provides a reliable theoretical principle for quantitative research of the fractured rock mass failure under seepage pressure.

Elbow, forearm, wrist, and hand injuries among sport rock climbers.

Science.gov (United States)

Holtzhausen, L M; Noakes, T D

1996-07-01

Sport rock climbing with its repetitive high-torque movements in gaining the ascent of a rock face or wall, often in steep overhanging positions, is associated with a unique distribution and form of upper limb injuries. In this article, we review the biomechanical aspects of sport rock climbing and the types of injuries commonly encountered in the forearm, wrist, and hand regions of elite sport rock climbers. Because elbow, forearm, wrist, and hand injuries predominate, representing 62% of the total injuries encountered, these anatomical areas have been selected for review. The predominant source of data are the published work of Bollen et al. The remaining sources were obtained through electronic search of the Medline and Current Contents Databases (last searched May 1995). German and French articles were included in the search criteria. Only studies dealing with acute soft tissue and overuse injuries amongst sport rock climbers were selected. Data were extracted directly from the sourced articles. The following injuries have been described in detail with regard to their presentation, diagnosis, treatment, and prevention amongst sport rock climbers: medial epicondylitis, brachialis tendonitis, biceps brachii tendonitis, ulnar collateral ligament sprain of the elbow, carpal tunnel syndrome, digital flexor tendon pulley sheath tears, interphalangeal joint effusions, fixed flexion deformities of the interphalangeal joints, and collateral ligament tears of the interphalangeal joints. Many of the injuries are specific to the handhold types used by the rock climber. Accurate diagnosis and effective treatment of these unique injuries will be facilitated by a wider understanding of the biomechanical aspects of rock climbing and an awareness of the patterns and incidence of injuries in this sport.

High Sr/Y rocks are not all adakites!

Science.gov (United States)

Moyen, Jean-François

2010-05-01

The name of "adakite" is used to describe a far too large group of rocks, whose sole common feature is high Sr/Y and La/Yb ratios. Defining adakites only by this criterion is misleading, as the definition of this group of rocks does include many other criteria, including major elements. In itself, high (or commonly moderate!) Sr/Y ratios can be achieved via different processes: melting of a high Sr/Y (and La/Yb) source; deep melting, with abundant residual garnet; fractional crystallization or AFC; or interactions of felsic melts with the mantle, causing selective enrichment in LREE and Sr over HREE. A database of the compositions of "adakitic" rocks - including "high silica" and "low silica" adakites, "continental" adakites and Archaean adakites—was assembled. Geochemical modeling of the potential processes is used to interpret it, and reveals that (1) the genesis of high-silica adakites requires high pressure evolution (be it by melting or fractionation), in equilibrium with large amounts of garnet; (2) low-silica adakites are explained by garnet-present melting of an adakite-metasomatized mantle, i.e at depths greater than 2.5 GPa; (3) "Continental" adakites is a term encompassing a huge range of rocks, with a corresponding diversity of petrogenetic processes, and most of them are different from both low- and high- silica adakites; in fact in many cases it is a complete misnomer and the rocks studied are high-K calc-alkaline granitoids or even S-type granites; (4) Archaean adakites show a bimodal composition range, with some very high Sr/Y examples (similar to part of the TTG suite) reflecting deep melting (> 2.0 GPa) of a basaltic source with a relatively high Sr/Y, while lower Sr/Y rocks formed by shallower (1.0 GPa) melting of similar sources. Comparison with the Archaean TTG suite highlights the heterogeneity of the TTGs, whose composition spreads the whole combined range of HSA and Archaean adakites, pointing to a diversity of sources and processes

Freeing Crop Genetics through the Open Source Seed Initiative.

Directory of Open Access Journals (Sweden)

Claire H Luby

2016-04-01

Full Text Available For millennia, seeds have been freely available to use for farming and plant breeding without restriction. Within the past century, however, intellectual property rights (IPRs have threatened this tradition. In response, a movement has emerged to counter the trend toward increasing consolidation of control and ownership of plant germplasm. One effort, the Open Source Seed Initiative (OSSI, www.osseeds.org, aims to ensure access to crop genetic resources by embracing an open source mechanism that fosters exchange and innovation among farmers, plant breeders, and seed companies. Plant breeders across many sectors have taken the OSSI Pledge to create a protected commons of plant germplasm for future generations.

Freeing Crop Genetics through the Open Source Seed Initiative.

Science.gov (United States)

Luby, Claire H; Goldman, Irwin L

2016-04-01

For millennia, seeds have been freely available to use for farming and plant breeding without restriction. Within the past century, however, intellectual property rights (IPRs) have threatened this tradition. In response, a movement has emerged to counter the trend toward increasing consolidation of control and ownership of plant germplasm. One effort, the Open Source Seed Initiative (OSSI, www.osseeds.org), aims to ensure access to crop genetic resources by embracing an open source mechanism that fosters exchange and innovation among farmers, plant breeders, and seed companies. Plant breeders across many sectors have taken the OSSI Pledge to create a protected commons of plant germplasm for future generations.

Acoustic emission of quasi-isotropic rock samples initiated by temperature gradients

Czech Academy of Sciences Publication Activity Database

Vasin, R.N.; Nikitin, A. N.; Lokajíček, Tomáš; Rudajev, Vladimír

2006-01-01

Roč. 42, č. 10 (2006), s. 815-823 ISSN 1069-3513 Institutional research plan: CEZ:AV0Z30460519; CEZ:AV0Z30130516 Keywords : seismoacoustic emission * rock sample * temperature gradient Subject RIV: DB - Geology ; Mineralogy Impact factor: 0.092, year: 2006

Simulation of crack propagation in rock in plasma blasting technology

Science.gov (United States)

Ikkurthi, V. R.; Tahiliani, K.; Chaturvedi, S.

Plasma Blasting Technology (PBT) involves the production of a pulsed electrical discharge by inserting a blasting probe in a water-filled cavity drilled in a rock, which produces shocks or pressure waves in the water. These pulses then propagate into the rock, leading to fracture. In this paper, we present the results of two-dimensional hydrodynamic simulations using the SHALE code to study crack propagation in rock. Three separate issues have been examined. Firstly, assuming that a constant pressure P is maintained in the cavity for a time τ , we have determined the P- τ curve that just cracks a given rock into at least two large-sized parts. This study shows that there exists an optimal pressure level for cracking a given rock-type and geometry. Secondly, we have varied the volume of water in which the initial energy E is deposited, which corresponds to different initial peak pressures Ppeak. We have determined the E- Ppeak curve that just breaks the rock into four large-sized parts. It is found that there must be an optimal Ppeak that lowers the energy consumption, but with acceptable probe damage. Thirdly, we have attempted to identify the dominant mechanism of rock fracture. We also highlight some numerical errors that must be kept in mind in such simulations.

A Rock Mechanics and Coupled Hydro mechanical Analysis of Geological Repository of High Level Nuclear Waste in Fractured Rocks

International Nuclear Information System (INIS)

Min, Kibok

2011-01-01

This paper introduces a few case studies on fractured hard rock based on geological data from Sweden, Korea is one of a few countries where crystalline rock is the most promising rock formation as a candidate site of geological repository of high level nuclear waste. Despite the progress made in the area of rock mechanics and coupled hydro mechanics, extensive site specific study on multiple candidate sites is essential in order to choose the optimal site. For many countries concerned about the safe isolation of nuclear wastes from the biosphere, disposal in a deep geological formation is considered an attractive option. In geological repository, thermal loading continuously disturbs the repository system in addition to disturbances a recent development in rock mechanics and coupled hydro mechanical study using DFN(Discrete Fracture Network) - DEM(Discrete Element Method) approach mainly applied in hard, crystalline rock containing numerous fracture which are main sources of deformation and groundwater flow

Oils and source rocks from the Anadarko Basin: Final report, March 1, 1985-March 15, 1995

Energy Technology Data Exchange (ETDEWEB)

Philp, R. P. [School of Geology and Geophysics, Univ. of Oklahoma, Norman, OK (United States)

1996-11-01

The research project investigated various geochemical aspects of oils, suspected source rocks, and tar sands collected from the Anadarko Basin, Oklahoma. The information has been used, in general, to investigate possible sources for the oils in the basin, to study mechanisms of oil generation and migration, and characterization of depositional environments. The major thrust of the recent work involved characterization of potential source formations in the Basin in addition to the Woodford shale. The formations evaluated included the Morrow, Springer, Viola, Arbuckle, Oil Creek, and Sylvan shales. A good distribution of these samples was obtained from throughout the basin and were evaluated in terms of source potential and thermal maturity based on geochemical characteristics. The data were incorporated into a basin modelling program aimed at predicting the quantities of oil that could, potentially, have been generated from each formation. The study of crude oils was extended from our earlier work to cover a much wider area of the basin to determine the distribution of genetically-related oils, and whether or not they were derived from single or multiple sources, as well as attempting to correlate them with their suspected source formations. Recent studies in our laboratory also demonstrated the presence of high molecular weight components(C{sub 4}-C{sub 80}) in oils and waxes from drill pipes of various wells in the region. Results from such a study will have possible ramifications for enhanced oil recovery and reservoir engineering studies.

Ion sources for initial use at the Holifield radioactive ion beam facility

International Nuclear Information System (INIS)

Alton, G.D.

1994-01-01

The Holifield Radioactive Ion Beam Facility (HRIBF) now under construction at the Oak Ridge National Laboratory will use the 25-MV tandem accelerator for the acceleration of radioactive ion beams to energies appropriate for research in nuclear physics; negative ion beams are, therefore, required for injection into the tandem accelerator. Because charge exchange is an efficient means for converting initially positive ion beams to negative ion beams, both positive and negative ion sources are viable options for use at the facility; the choice of the type of ion source will depend on the overall efficiency for generating the radioactive species of interest. A high-temperature version of the CERN-ISOLDE positive ion source has been selected and a modified version of the source designed and fabricated for initial use at the HRIBF because of its low emittance, relatively high ionization efficiencies and species versatility, and because it has been engineered for remote installation, removal and servicing as required for safe handling in a high-radiation-level ISOL facility. Prototype plasma-sputter negative ion sources and negative surfaceionization sources are also under design consideration for generating negative radioactive ion beams from high electron-affinity elements. A brief review of the HRIBF will be presented, followed by a detailed description of the design features, operational characteristics, ionization efficiencies, and beam qualities (emittances) of these sources

Hot dry rock heat mining

International Nuclear Information System (INIS)

Duchane, D.V.

1992-01-01

Geothermal energy utilizing fluids from natural sources is currently exploited on a commercial scale at sites around the world. A much greater geothermal resource exists, however, in the form of hot rock at depth which is essentially dry. This hot dry rock (HDR) resource is found almost everywhere, but the depth at which usefully high temperatures are reached varies from place to place. The technology to mine the thermal energy from HDR has been under development for a number of years. Using techniques adapted from the petroleum industry, water is pumped at high pressure down an injection well to a region of usefully hot rock. The pressure forces open natural joints to form a reservoir consisting of a small amount of water dispensed in a large volume of hot rock. This reservoir is tapped by second well located at some distance from the first, and the heated water is brought to the surface where its thermal energy is extracted. The same water is then recirculated to mine more heat. Economic studies have indicated that it may be possible to produce electricity at competitive prices today in regions where hot rock is found relatively close to the surface

Recovery Act: Tennessee Energy Efficient Schools Initiative Ground Source Heat Pump Program

Energy Technology Data Exchange (ETDEWEB)

Townsend, Terry [Townsend Engineering, Inc., Davenport, IA (United States); Slusher, Scott [Townsend Engineering, Inc., Davenport, IA (United States)

2017-04-24

The Tennessee Energy Efficient Schools Initiative (EESI) Hybrid-Water Source Heat Pump (HY-GSHP) Program sought to provide installation costs and operation costs for different Hybrid water source heat pump systems’ configurations so that other State of Tennessee School Districts will have a resource for comparison purposes if considering a geothermal system.

The effects of bacteria on crystalline rock

International Nuclear Information System (INIS)

Brown, D.A.

1994-01-01

Many reactions involving inorganic minerals at water-rock interfaces have now been recognized to be bacterially mediated; these reactions could have a significant effect in the excavation of vaults for toxic and radioactive waste disposal. To investigate the role that bacteria play in the natural aqueous environment of crystalline rock the microbial growth factors of nutrition, energy and environment are described. Microbial activity has been investigated in Atomic Energy of Canada's Underground Research Laboratory (URL), situated in the Archean granitic Lac du Bonnet Batholith, Winnipeg, Manitoba. Faults, initiated in the Early Proterozoic, and later-formed fractures, provide ground-water pathways. Planktonic bacteria, free-swimming in the groundwater, have been observed in over 100 underground borehole samples. The number of bacteria varied from 10 3 to 10 5 mL -1 and appeared to decrease with depth and with increased salinity of the water. However, in the natural environment of deep (100-500 m) crystalline rocks, where nutrition is limited, formation of biofilms by sessile bacteria is a successful survival strategy. Natural biofilms at the URL and biofilms grown in bioreactors have been studied. The biofilms can accumulate different elements, depending upon the local environment. Precipitates of iron have been found in all the biofilms studied, where they are either passively accumulated or utilized as an energy source. Within the biofilm active and extensive biogeochemical immobilization of dissolved elements is controlled by distinct bacterial activities which are sufficiently discrete for hematite and siderite to be precipitated in close proximity

Mechanical Properties and Acoustic Emission Properties of Rocks with Different Transverse Scales

Directory of Open Access Journals (Sweden)

Xi Yan

2017-01-01

Full Text Available Since the stability of engineering rock masses has important practical significance to projects like mining, tunneling, and petroleum engineering, it is necessary to study mechanical properties and stability prediction methods for rocks, cementing materials that are composed of minerals in all shapes and sizes. Rocks will generate acoustic emission during damage failure processes, which is deemed as an effective means of monitoring the stability of coal rocks. In the meantime, actual mining and roadway surrounding rocks tend to have transverse effects; namely, the transverse scale is larger than the length scale. Therefore, it is important to explore mechanical properties and acoustic emission properties of rocks under transverse size effects. Considering the transverse scale effects of rocks, this paper employs the microparticle flow software PFC2D to explore the influence of different aspect ratios on damage mechanics and acoustic emission properties of rocks. The results show that (1 the transverse scale affects uniaxial compression strength of rocks. As the aspect ratio increases, uniaxial compression strength of rocks decreases initially and later increases, showing a V-shape structure and (2 although it affects the maximum hit rate and the strain range of acoustic emission, it has little influence on the period of occurrence. As the transverse scale increases, both damage degree and damage rate of rocks decrease initially and later increase.

Site investigations: Strategy for rock mechanics site descriptive model

International Nuclear Information System (INIS)

Andersson, Johan; Christiansson, Rolf; Hudson, John

2002-05-01

As a part of the planning work for the Site Investigations, SKB has developed a Rock Mechanics Site Descriptive Modelling Strategy. Similar strategies are being developed for other disciplines. The objective of the strategy is that it should guide the practical implementation of evaluating site specific data during the Site Investigations. It is also understood that further development may be needed. This methodology enables the crystalline rock mass to be characterised in terms of the quality at different sites, for considering rock engineering constructability, and for providing the input to numerical models and performance assessment calculations. The model describes the initial stresses and the distribution of deformation and strength properties of the intact rock, of fractures and fracture zones, and of the rock mass. The rock mass mechanical properties are estimated by empirical relations and by numerical simulations. The methodology is based on estimation of mechanical properties using both empirical and heroretical/numerical approaches; and estimation of in situ rock stress using judgement and numerical modelling, including the influence of fracture zones. These approaches are initially used separately, and then combined to produce the required characterisation estimates. The methodology was evaluated with a Test Case at the Aespoe Hard Rock Laboratory in Sweden. The quality control aspects are an important feature of the methodology: these include Protocols to ensure the structure and coherence of the procedures used, regular meetings to enhance communication, feedback from internal and external reviewing, plus the recording of an audit trail of the development steps and decisions made. The strategy will be reviewed and, if required, updated as appropriate

Site investigations: Strategy for rock mechanics site descriptive model

Energy Technology Data Exchange (ETDEWEB)

Andersson, Johan [JA Streamflow AB, Aelvsjoe (Sweden); Christiansson, Rolf [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Hudson, John [Rock Engineering Consultants, Welwyn Garden City (United Kingdom)

2002-05-01

As a part of the planning work for the Site Investigations, SKB has developed a Rock Mechanics Site Descriptive Modelling Strategy. Similar strategies are being developed for other disciplines. The objective of the strategy is that it should guide the practical implementation of evaluating site specific data during the Site Investigations. It is also understood that further development may be needed. This methodology enables the crystalline rock mass to be characterised in terms of the quality at different sites, for considering rock engineering constructability, and for providing the input to numerical models and performance assessment calculations. The model describes the initial stresses and the distribution of deformation and strength properties of the intact rock, of fractures and fracture zones, and of the rock mass. The rock mass mechanical properties are estimated by empirical relations and by numerical simulations. The methodology is based on estimation of mechanical properties using both empirical and heroretical/numerical approaches; and estimation of in situ rock stress using judgement and numerical modelling, including the influence of fracture zones. These approaches are initially used separately, and then combined to produce the required characterisation estimates. The methodology was evaluated with a Test Case at the Aespoe Hard Rock Laboratory in Sweden. The quality control aspects are an important feature of the methodology: these include Protocols to ensure the structure and coherence of the procedures used, regular meetings to enhance communication, feedback from internal and external reviewing, plus the recording of an audit trail of the development steps and decisions made. The strategy will be reviewed and, if required, updated as appropriate.

Host rock characteristics of uranium deposits of cataclastic-altered granite type

International Nuclear Information System (INIS)

Feng Mingyue

1997-01-01

The author expounds the host rock characteristics of uranium deposits of cataclastic-altered granite type, i.e., the high initial content of uranium, the high cataclasis of host rocks, the strong alteration of host rocks, the simple composition of host rocks favourable for the leaching of uranium, as well as the low content of harmful associated elements. These characteristics may be regarded as petrological criteria for recognition and prospecting for such type of uranium deposits

Host rock characteristics of uranium deposits of cataclastic-altered granite type

Energy Technology Data Exchange (ETDEWEB)

Mingyue, Feng [Beijing Research Inst. of Uranium Geology (China)

1997-03-01

The author expounds the host rock characteristics of uranium deposits of cataclastic-altered granite type, i.e., the high initial content of uranium, the high cataclasis of host rocks, the strong alteration of host rocks, the simple composition of host rocks favourable for the leaching of uranium, as well as the low content of harmful associated elements. These characteristics may be regarded as petrological criteria for recognition and prospecting for such type of uranium deposits.

Some clastic rocks as parent rocks in beech forests of Brezovica - Južni Kučaj

Directory of Open Access Journals (Sweden)

Joksimović Vesna

2003-01-01

Full Text Available On the large forest areas, where the measures of soil quality improvement are absent or rarely undertaken, the rocks are the sources of a great number of elements in plant nutrition and one of the factors affecting the contents of some elements in plants. The aim of the study is to determine the differences in the contents of Cu, Zn, Mn, Ni, Fe, Cd, Co, Pb and Cr in the beech leaves developed in the same climate conditions, on morphologically similar terrains, composed of different types of sedimentary rocks. This paper presents the study results of the contents of the above elements in argillites, sandstones (grauwackes and microconglomerates occurring as the parent rocks in high beech forests in the region of GJ Bogovina (Brezovica Južni Kučaj and in the leaves of beech developed on these rocks.

Pore Type Classification on Carbonate Reservoir in Offshore Sarawak using Rock Physics Model and Rock Digital Images

International Nuclear Information System (INIS)

Lubis, L A; Harith, Z Z T

2014-01-01

It has been recognized that carbonate reservoirs are one of the biggest sources of hydrocarbon. Clearly, the evaluation of these reservoirs is important and critical. For rigorous reservoir characterization and performance prediction from geophysical measurements, the exact interpretation of geophysical response of different carbonate pore types is crucial. Yet, the characterization of carbonate reservoir rocks is difficult due to their complex pore systems. The significant diagenesis process and complex depositional environment makes pore systems in carbonates far more complicated than in clastics. Therefore, it is difficult to establish rock physics model for carbonate rock type. In this paper, we evaluate the possible rock physics model of 20 core plugs of a Miocene carbonate platform in Central Luconia, Sarawak. The published laboratory data of this area were used as an input to create the carbonate rock physics models. The elastic properties were analyzed to examine the validity of an existing analytical carbonate rock physics model. We integrate the Xu-Payne Differential Effective Medium (DEM) Model and the elastic modulus which was simulated from a digital carbonate rock image using Finite Element Modeling. The results of this integration matched well for the separation of carbonate pore types and sonic P-wave velocity obtained from laboratory measurement. Thus, the results of this study show that the integration of rock digital image and theoretical rock physics might improve the elastic properties prediction and useful for more advance geophysical techniques (e.g. Seismic Inversion) of carbonate reservoir in Sarawak

Ages and petrogenesis of Jurassic and Cretaceous intrusive rocks in the Matsu Islands: Implications for lower crust modification beneath southeastern China

Science.gov (United States)

Chen, Jing-Yuan; Yang, Jin-Hui; Ji, Wei-Qiang

2017-12-01

Major and trace element, whole-rock Sr-, Nd- and Hf-isotope, zircon U-Pb age and Hf-O isotope data are reported for the intrusive rocks from the Matsu Islands in the coastal area of southeastern (SE) China, in order to study the ages, sources and petrogenesis of these rocks and evolution of the lower crust. The rocks include gneissic granite, massive granite, brecciated granite and diabase. Secondary ion mass spectrometer (SIMS) zircon U-Pb dating reveals that the rocks in the Matsu Islands were emplaced at ∼160 Ma, ∼130 Ma and ∼94 Ma. The Jurassic granites (∼160 Ma) have high SiO2 (74.1-74.5 wt%) and K2O + Na2O (8.32-8.33 wt%) contents and high Rb/Sr ratios of 0.6-1.2 and (La/Yb)CN ratios of 12.6-19.4. Their relatively high initial 87Sr/86Sr ratios (0.7074-0.7101), variable and negative εNd(t) values (-9.2 to -5.4), and variable zircon εHf(t) (-17.0 to +5.2) and δ18O (4.7-8.1‰) values indicate they were mainly derived from an ancient lower crustal source, but with involvement of high εHf(t) and low δ18O materials. The Early Cretaceous diabase (∼130 Ma) has SiO2 content of 56.5 wt%, relatively high MgO concentration, low initial 87Sr/86Sr ratio and negative εNd(t) value, similar to geochemical features of other Cretaceous mafic rocks in the coastal area of SE China. Zircons from the diabase have high εHf(t) values (-5.5 to +0.2) and relatively low δ18O values of 4.2-5.0‰. These characteristics indicate that the parental magma of the diabase was generated by partial melting of enriched lithospheric mantle, which have been metasomatised by altered oceanic crust-derived low-δ18O fluids. For the Cretaceous granitoids (∼130 Ma and 94 Ma), they have relatively low SiO2 (68.0-71.3 wt%) and K2O + Na2O (5.30-7.55 wt%) contents and low Rb/Sr ratios and (La/Yb)CN ratios of 5.8-7.1. They have low initial 87Sr/86Sr ratios (0.7071-0.7082), homogeneous εNd(t) (-4.3 to -4.5) and relatively high zircon εHf(t) values (-3.7 to +1.2) and low δ18O values (4

Simulation of rock deformation behavior

Directory of Open Access Journals (Sweden)

Я. И. Рудаев

2016-12-01

Full Text Available A task of simulating the deformation behavior of geomaterials under compression with account of over-extreme branch has been addressed. The physical nature of rock properties variability as initially inhomogeneous material is explained by superposition of deformation and structural transformations of evolutionary type within open nonequilibrium systems. Due to this the description of deformation and failure of rock is related to hierarchy of instabilities within the system being far from thermodynamic equilibrium. It is generally recognized, that the energy function of the current stress-strain state is a superposition of potential component and disturbance, which includes the imperfection parameter accounting for defects not only existing in the initial state, but also appearing under load. The equation of state has been obtained by minimizing the energy function by the order parameter. The imperfection parameter is expressed through the strength deterioration, which is viewed as the internal parameter of state. The evolution of strength deterioration has been studied with the help of Fokker – Planck equation, which steady form corresponds to rock statical stressing. Here the diffusion coefficient is assumed to be constant, while the function reflecting internal sliding and loosening of the geomaterials is assumed as an antigradient of elementary integration catastrophe. Thus the equation of state is supplemented with a correlation establishing relationship between parameters of imperfection and strength deterioration. While deformation process is identified with the change of dissipative media, coupled with irreversible structural fluctuations. Theoretical studies are proven with experimental data obtained by subjecting certain rock specimens to compression.

A COMPARISON OF MAJOR ELEMENTS BETWEEN MARINE SEDIMENTS AND IGNEOUS ROCKS: AS A BASIC DETERMINATION OF THE SEDIMENT SOURCE AT UJUNG PENYUSUK WATERS, NORTH BANGKA,BANGKA BELITUNG PROVINCE

Directory of Open Access Journals (Sweden)

Ediar Usman

2017-07-01

Full Text Available Three igneous rock samples from the coast and five sediments from the marine of Ujung Penyusuk Waters have been used for chemistry analysis as the basic determination of sediment source. The result of chemistry analysis shows that the major element with relatively same pattern. In the igneous rock samples, the result of chemistry analysis shows the SiO2 ranges between 72.3 - 76.8%, Al2O3 (9.64 - 11.64%, and Fe2O3 ( 2.08 - 2.18%. In the marine sediment, the content of SiO2 is between 62.2 and 66.5%, Al2O3 (2.93 - 3.63% and Fe2O3 (21.19 - 24.40%. Other elements such as CaO, MgO, K2O, Na2O and TiO2 are relatively similar values in all samples. The difference of element content in marine sediment and coastal igneous rock occurs in Al2O3 and Fe2O3. The Al2O3 is small in marine sediment while the Fe2O3 is higher compared to igneous rocks. Decreasing of the Al2O3 (kaolinite in the marine sediment is caused by the character of the Al2O3 that was derived from quartz rich of igneous rocks forming kaolinite. It was than deposited in the sea floor. Increasing of the Fe2O3 in marine sediment is caused by addition reaction of the Fe from the sea. Generally, the content of the SiO2 (quartz in igneous rock and marine sediment belongs to the same group source that is acid igneous rock. The SiO2 in the sediment belongs to a group of granitoid.

Petrogenesis of siliceous high-Mg series rocks as exemplified by the Early Paleoproterozoic mafic volcanic rocks of the Eastern Baltic Shield: enriched mantle versus crustal contamination

Science.gov (United States)

Bogina, Maria; Zlobin, Valeriy; Sharkov, Evgenii; Chistyakov, Alexeii

2015-04-01

The Early Paleoproterozoic stage in the Earth's evolution was marked by the initiation of global rift systems, the tectonic nature of which was determined by plume geodynamics. These processes caused the voluminous emplacement of mantle melts with the formation of dike swarms, mafic-ultramafic layered intrusions, and volcanic rocks. All these rocks are usually considered as derivatives of SHMS (siliceous high-magnesian series). Within the Eastern Baltic Shield, the SHMS volcanic rocks are localized in the domains with different crustal history: in the Vodlozero block of the Karelian craton with the oldest (Middle Archean) crust, in the Central Block of the same craton with the Neoarchean crust, and in the Kola Craton with a heterogeneous crust. At the same time, these rocks are characterized by sufficiently close geochemical characteristics: high REE fractionation ((La/Yb)N = 4.9-11.7, (La/Sm)N=2.3-3.6, (Gd/Yb)N =1.66-2.74)), LILE enrichment, negative Nb anomaly, low to moderate Ti content, and sufficiently narrow variations in Nd isotope composition from -2.0 to -0.4 epsilon units. The tectonomagmatic interpretation of these rocks was ambiguous, because such characteristics may be produced by both crustal contamination of depleted mantle melts, and by generation from a mantle source metasomatized during previous subduction event. Similar REE patterns and overlapping Nd isotope compositions indicate that the studied basaltic rocks were formed from similar sources. If crustal contamination en route to the surface would play a significant role in the formation of the studied basalts, then almost equal amounts of contaminant of similar composition are required to produce the mafic rocks with similar geochemical signatures and close Nd isotopic compositions, which is hardly possible for the rocks spaced far apart in a heterogeneous crust. This conclusion is consistent with analysis of some relations between incompatible elements and their ratios. In particular, the

Assessment of Thermal Maturity Trends in Devonian–Mississippian Source Rocks Using Raman Spectroscopy: Limitations of Peak-Fitting Method

Energy Technology Data Exchange (ETDEWEB)

Lupoi, Jason S., E-mail: jlupoi@rjlg.com; Fritz, Luke P. [RJ Lee Group, Inc., Monroeville, PA (United States); Parris, Thomas M. [Kentucky Geological Survey, University of Kentucky, Lexington, KY (United States); Hackley, Paul C. [UniversityS. Geological Survey, Reston, VA (United States); Solotky, Logan [RJ Lee Group, Inc., Monroeville, PA (United States); Eble, Cortland F. [Kentucky Geological Survey, University of Kentucky, Lexington, KY (United States); Schlaegle, Steve [RJ Lee Group, Inc., Monroeville, PA (United States)

2017-09-27

The thermal maturity of shale is often measured by vitrinite reflectance (VRo). VRo measurements for the Devonian–Mississippian black shale source rocks evaluated herein predicted thermal immaturity in areas where associated reservoir rocks are oil-producing. This limitation of the VRo method led to the current evaluation of Raman spectroscopy as a suitable alternative for developing correlations between thermal maturity and Raman spectra. In this study, Raman spectra of Devonian–Mississippian black shale source rocks were regressed against measured VRo or sample-depth. Attempts were made to develop quantitative correlations of thermal maturity. Using sample-depth as a proxy for thermal maturity is not without limitations as thermal maturity as a function of depth depends on thermal gradient, which can vary through time, subsidence rate, uplift, lack of uplift, and faulting. Correlations between Raman data and vitrinite reflectance or sample-depth were quantified by peak-fitting the spectra. Various peak-fitting procedures were evaluated to determine the effects of the number of peaks and maximum peak widths on correlations between spectral metrics and thermal maturity. Correlations between D-frequency, G-band full width at half maximum (FWHM), and band separation between the G- and D-peaks and thermal maturity provided some degree of linearity throughout most peak-fitting assessments; however, these correlations and those calculated from the G-frequency, D/G FWHM ratio, and D/G peak area ratio also revealed a strong dependence on peak-fitting processes. This dependency on spectral analysis techniques raises questions about the validity of peak-fitting, particularly given the amount of subjective analyst involvement necessary to reconstruct spectra. This research shows how user interpretation and extrapolation affected the comparability of different samples, the accuracy of generated trends, and therefore, the potential of the Raman spectral method to become an

Assessment of Thermal Maturity Trends in Devonian–Mississippian Source Rocks Using Raman Spectroscopy: Limitations of Peak-Fitting Method

International Nuclear Information System (INIS)

Lupoi, Jason S.; Fritz, Luke P.; Parris, Thomas M.; Hackley, Paul C.; Solotky, Logan; Eble, Cortland F.; Schlaegle, Steve

2017-01-01

The thermal maturity of shale is often measured by vitrinite reflectance (VRo). VRo measurements for the Devonian–Mississippian black shale source rocks evaluated herein predicted thermal immaturity in areas where associated reservoir rocks are oil-producing. This limitation of the VRo method led to the current evaluation of Raman spectroscopy as a suitable alternative for developing correlations between thermal maturity and Raman spectra. In this study, Raman spectra of Devonian–Mississippian black shale source rocks were regressed against measured VRo or sample-depth. Attempts were made to develop quantitative correlations of thermal maturity. Using sample-depth as a proxy for thermal maturity is not without limitations as thermal maturity as a function of depth depends on thermal gradient, which can vary through time, subsidence rate, uplift, lack of uplift, and faulting. Correlations between Raman data and vitrinite reflectance or sample-depth were quantified by peak-fitting the spectra. Various peak-fitting procedures were evaluated to determine the effects of the number of peaks and maximum peak widths on correlations between spectral metrics and thermal maturity. Correlations between D-frequency, G-band full width at half maximum (FWHM), and band separation between the G- and D-peaks and thermal maturity provided some degree of linearity throughout most peak-fitting assessments; however, these correlations and those calculated from the G-frequency, D/G FWHM ratio, and D/G peak area ratio also revealed a strong dependence on peak-fitting processes. This dependency on spectral analysis techniques raises questions about the validity of peak-fitting, particularly given the amount of subjective analyst involvement necessary to reconstruct spectra. This research shows how user interpretation and extrapolation affected the comparability of different samples, the accuracy of generated trends, and therefore, the potential of the Raman spectral method to become an

Assessment of Thermal Maturity Trends in Devonian–Mississippian Source Rocks Using Raman Spectroscopy: Limitations of Peak-Fitting Method

Directory of Open Access Journals (Sweden)

Jason S. Lupoi

2017-09-01

Full Text Available The thermal maturity of shale is often measured by vitrinite reflectance (VRo. VRo measurements for the Devonian–Mississippian black shale source rocks evaluated herein predicted thermal immaturity in areas where associated reservoir rocks are oil-producing. This limitation of the VRo method led to the current evaluation of Raman spectroscopy as a suitable alternative for developing correlations between thermal maturity and Raman spectra. In this study, Raman spectra of Devonian–Mississippian black shale source rocks were regressed against measured VRo or sample-depth. Attempts were made to develop quantitative correlations of thermal maturity. Using sample-depth as a proxy for thermal maturity is not without limitations as thermal maturity as a function of depth depends on thermal gradient, which can vary through time, subsidence rate, uplift, lack of uplift, and faulting. Correlations between Raman data and vitrinite reflectance or sample-depth were quantified by peak-fitting the spectra. Various peak-fitting procedures were evaluated to determine the effects of the number of peaks and maximum peak widths on correlations between spectral metrics and thermal maturity. Correlations between D-frequency, G-band full width at half maximum (FWHM, and band separation between the G- and D-peaks and thermal maturity provided some degree of linearity throughout most peak-fitting assessments; however, these correlations and those calculated from the G-frequency, D/G FWHM ratio, and D/G peak area ratio also revealed a strong dependence on peak-fitting processes. This dependency on spectral analysis techniques raises questions about the validity of peak-fitting, particularly given the amount of subjective analyst involvement necessary to reconstruct spectra. This research shows how user interpretation and extrapolation affected the comparability of different samples, the accuracy of generated trends, and therefore, the potential of the Raman spectral

A thermo-elastic model for soft rocks considering structure

International Nuclear Information System (INIS)

He, Z.; Zhang, S.; Teng, J.; Xiong, Y.

2017-01-01

In the fields of nuclear waste geological deposit, geothermal energy and deep mining, the effects of temperature on the mechanical behaviors of soft rocks cannot be neglected. Experimental data in the literature also showed that the structure of soft rocks cannot be ignored. Based on the super-loading yield surface and the concept of temperature-deduced equivalent stress, a thermo-elastoplastic model for soft rocks is proposed considering the structure. Compared to the super-loading yield surface, only one parameter is added, i.e. the linear thermal expansion coefficient. The predicted results and the comparisons with experimental data in the literature show that the proposed model is capable of simultaneously describing heat increase and heat decrease of soft rocks. A stronger initial structure leads to a greater strength of the soft rocks. Heat increase and heat decrease can be converted between each other due to the change of the initial structure of soft rocks. Furthermore, regardless of the heat increase or heat decrease, a larger linear thermal expansion coefficient or a greater temperature always leads to a much rapider degradation of the structure. The degradation trend will be more obvious for the coupled greater values of linear thermal expansion coefficient and temperature. Lastly, compared to heat decrease, the structure will degrade more easily in the case of heat increase. (authors)

A thermo-elastoplastic model for soft rocks considering structure

Science.gov (United States)

He, Zuoyue; Zhang, Sheng; Teng, Jidong; Xiong, Yonglin

2017-11-01

In the fields of nuclear waste geological deposit, geothermy and deep mining, the effects of temperature on the mechanical behaviors of soft rocks cannot be neglected. Experimental data in the literature also showed that the structure of soft rocks cannot be ignored. Based on the superloading yield surface and the concept of temperature-deduced equivalent stress, a thermo-elastoplastic model for soft rocks is proposed considering the structure. Compared to the superloading yield surface, only one parameter is added, i.e. the linear thermal expansion coefficient. The predicted results and the comparisons with experimental data in the literature show that the proposed model is capable of simultaneously describing heat increase and heat decrease of soft rocks. A stronger initial structure leads to a greater strength of the soft rocks. Heat increase and heat decrease can be converted between each other due to the change of the initial structure of soft rocks. Furthermore, regardless of the heat increase or heat decrease, a larger linear thermal expansion coefficient or a greater temperature always leads to a much rapider degradation of the structure. The degradation trend will be more obvious for the coupled greater values of linear thermal expansion coefficient and temperature. Lastly, compared to heat decrease, the structure will degrade more easily in the case of heat increase.

Thermal conductivity of the rocks in the Bureau of Mines Standard Rock Suite

International Nuclear Information System (INIS)

Morgan, M.T.; West, G.A.

1980-01-01

Thermal conductivities of eight rocks from the Bureau of Mines Standard Rock Suite were measured in air over the temperature range 373 to 533 0 K (100 to 260 0 C). The thermal conductivities of these rocks were measured to furnish standards for future comparisons with host rock from prospective nuclear waste repository sites. The thermal conductivity at a given temperature decreased by as much as 9% after a specimen had been heated to the maximum temperature (533 0 K), but additional heating cycles had no further effect. This decrease was smallest in the igneous rocks and largest in the sedimentary types. Variations due to orientation were within the precision of measurements (+- 5%). In most cases the thermal conductivities were linear with the reciprocal of the temperature and were within 14% of published data obtained by other methods. Measurements were made by a cut-bar comparison method in which the sample was sandwiched between two reference or metering bars made of Pyroceram 9606 glass-ceramic. The apparatus consisted of a Dynatech Model TCFCM-N20 comparative thermal conductivity analyzer controlled by a Hewlett Packard Model 3052A data acquisition system. A program was written to increment and cycle the temperature in steps between predetermined initial and maximum values. At each step the thermal conductivity was measured after steady-state conditions were established. The rocks furnished by the Bureau of Mines were quarried in large and fairly homogeneous lots for use by researchers at various laboratories. To investigate any anisotropy, cores were taken from each rock cube perpendicular to each of the cube faces. Samples 2 in. in diameter and approx. 0.75 in. thick were prepared from the cores and were dried in a vacuum oven for at least one month prior to taking measurements

Experimental Characterization of Stress- and Strain-Dependent Stiffness in Grouted Rock Masses.

Science.gov (United States)

Kim, Ji-Won; Chong, Song-Hun; Cho, Gye-Chun

2018-03-29

Grouting of fractured rock mass prior to excavation results in grout-filled discontinuities that govern the deformation characteristics of a site. The influence of joint characteristics on the properties of grouted rocks is important in assessing the effects of grouting on jointed rock mass. However, grouting remains a predominantly empirical practice and the effects of grouting on rock joint behavior and material properties have yet to be accurately assessed. Granular materials, including jointed rocks, typically display nonlinear strain-dependent responses that can be characterized by the shear modulus degradation curve. In this study, the effects of grouting on the strain-dependent shear stiffness of jointed rock mass were investigated at the small-strain (below 10 -5 ) and mid-strain (10 -5 to 10 -3 ) ranges using the quasi-static resonant column test and rock mass dynamic test devices. The effects of curing time, axial stress, initial joint roughness, and grouted joint thickness were examined. The results show that (1) grouting of rock joints leads to decreased stress sensitivity and increased small-strain shear stiffness for all tested samples; (2) the grouted rock samples display similar modulus degradation characteristics as the applied grout material; (3) the initial joint roughness determines the stress-dependent behaviors and general stiffness range of the jointed and grouted rocks, but the strain-dependent behaviors are dependent on the properties of the grout material; (4) increased grouted joint thickness results in larger contribution of the grout properties in the overall grouted rock mass.

Technical evaluation of the proposed changes in the technical specifications for emergency power sources for the Big Rock Point nuclear power plant

International Nuclear Information System (INIS)

Latorre, V.R.

1979-12-01

The technical evaluation is presented for the proposed changes to the Technical Specifications for emergency power sources for the Big Rock Point nuclear power plant. The criteria used to evaluate the acceptability of the changes include those delineated in IEEE Std-308-1974, and IEEE Std-450-1975 as endorsed by US NRC Regulatory Guide 1.129

Characteristics of mesozoic magmatic rocks in western Zhejiang and their relation with uranium mineralization

International Nuclear Information System (INIS)

Zhou Jiazhi

2000-01-01

The author summarizes characteristics of Mesozoic (Yangshanian Period) acid-intermediate volcanics, sub-volcanics and basic intrusive from aspects of formation time of rock series, petrogenic sequence, chemical composition, rock -controlling factors and petrogenic environments. It is suggested that these rocks were originated from different source areas of crust and mantle. Based on the time-space relation between different types uranium deposits and magmatic rocks, the author proposes that: the earlier stage (Earlier Cretaceous) U-hematite ores were originated from acid volcanic magmatism of crustal source, but the later stage (Late Cretaceous) pitchblende-polymetallic sulfide and pitchblende-purple fluorite rich ores were derived from basic magmatism of mantle source. Finally, the author proposes prospecting criteria of the above two types of uranium deposits

Failure Mechanism of Rock Bridge Based on Acoustic Emission Technique

Directory of Open Access Journals (Sweden)

Guoqing Chen

2015-01-01

Full Text Available Acoustic emission (AE technique is widely used in various fields as a reliable nondestructive examination technology. Two experimental tests were carried out in a rock mechanics laboratory, which include (1 small scale direct shear tests of rock bridge with different lengths and (2 large scale landslide model with locked section. The relationship of AE event count and record time was analyzed during the tests. The AE source location technology and comparative analysis with its actual failure model were done. It can be found that whether it is small scale test or large scale landslide model test, AE technique accurately located the AE source point, which reflected the failure generation and expansion of internal cracks in rock samples. Large scale landslide model with locked section test showed that rock bridge in rocky slope has typical brittle failure behavior. The two tests based on AE technique well revealed the rock failure mechanism in rocky slope and clarified the cause of high speed and long distance sliding of rocky slope.

Demonstration of a Fractured Rock Geophysical Toolbox (FRGT) for Characterization and Monitoring of DNAPL Biodegradation in Fractured Rock Aquifers

Science.gov (United States)

2015-09-29

is characterized by dark gray slate or phyllite, alternating with thin layers of light gray siltstone or sandstone . Table 1 summarizes the primary...sedimentary rocks of the Newark Basin. Competent rocks are primarily mudstones and sandstones of the Lockatong and Stockton Formations. Fill, weathered silt... sandstone , and characterized by water bearing bedding plane fractures. An array of open boreholes in the source area that were drilled for the 2002

The origin of groundwater salinity in granitic rocks: identification and characterisation of chloride sources

International Nuclear Information System (INIS)

Savoye, Sebastien

1998-01-01

This research thesis aims at clearly identifying the possible origins of chlorine in solution in underground waters in a granitic environment, and is thus a first step in the prediction of concentration of dissolved compounds in waters in crystalline environment, with respect to the geological context. In a first part, the author proposes a synthetic and critical overview of knowledge and previous studies: definition of the term 'salinity', presentation of geochemical tracers, presentation of available data on potential chlorine sources in granitic rocks. The author then describes the experimental protocols and studied sites, reports results of the characterisation of different chlorine tanks performed on samples from each studied site. Based on mass assessment calculations and on the use of tracers, the author finally discusses the contribution of each of the chlorine tanks to the salinity of underground waters [fr

Initial assessment of the thermal stresses around a radioactive waste depository in hard rock

International Nuclear Information System (INIS)

Hodgkinson, D.P.; Bourke, P.J.

1980-01-01

The disposal of heat emitting radioactive waste into hard rock should result in temperature rises and thermal gradients over distances of several hundred metres for several centuries. The consequent constrained thermal expansion of the rock would induce stresses which have important implications for possible water-borne leakage of radionuclides and for depository design. These problems are assessed by considering a simplified mathematical model for which analytic solutions to the temperature and stress fields are derived. (author)

Atucha-I source terms for sequences initiated by transients

International Nuclear Information System (INIS)

Baron, J.; Bastianelli, B.

1997-01-01

The present work is part of an expected source terms study in the Atucha I nuclear power plant during severe accidents. From the accident sequences with a significant probability to produce core damage, those initiated by operational transients have been identified as the most relevant. These sequences have some common characteristics, in the sense that all of them resume in the opening of the primary system safety valves, and leave this path open for the coolant loss. In the case these sequences continue as severe accidents, the same path will be used for the release of the radionuclides, from the core, through the primary system and to the containment. Later in the severe accident sequence, the failure of the pressure vessel will occur, and the corium will fall inside the reactor cavity, interacting with the concrete. During these processes, more radioactive products will be released inside the containment. In the present work the severe accident simulation initiated by a blackout is performed, from the point of view of the phenomenology of the behavior of the radioactive products, as they are transported in the piping, during the core-concrete interactions, and inside the containment buildings until it failure. The final result is the source term into the atmosphere. (author) [es

Organic richness and organic matter quality studies of source rocks ...

African Journals Online (AJOL)

The hydrocarbon potential of the Upper Cretaceous units (Maastrichtian Mamu Formation) exposed at Imiegba and environs of the Benin Flank, Western Anambra Basin was assessed by Total Organic Carbon (TOC) and Rock-Eval Pyrolysis Analyses. The investigated sections of the Mamu Formation consist of dark grey to ...

Xenon NMR measurements of permeability and tortuosity in reservoir rocks.

Science.gov (United States)

Wang, Ruopeng; Pavlin, Tina; Rosen, Matthew Scott; Mair, Ross William; Cory, David G; Walsworth, Ronald Lee

2005-02-01

In this work we present measurements of permeability, effective porosity and tortuosity on a variety of rock samples using NMR/MRI of thermal and laser-polarized gas. Permeability and effective porosity are measured simultaneously using MRI to monitor the inflow of laser-polarized xenon into the rock core. Tortuosity is determined from measurements of the time-dependent diffusion coefficient using thermal xenon in sealed samples. The initial results from a limited number of rocks indicate inverse correlations between tortuosity and both effective porosity and permeability. Further studies to widen the number of types of rocks studied may eventually aid in explaining the poorly understood connection between permeability and tortuosity of rock cores.

Determining the Accuracy of Paleomagnetic Remanence and High-Resolution Chronostratigraphy for Sedimentary Rocks using Rock Magnetics

Science.gov (United States)

Kodama, K. P.

2017-12-01

The talk will consider two broad topics in rock magnetism and paleomagnetism: the accuracy of paleomagnetic remanence and the use of rock magnetics to measure geologic time in sedimentary sequences. The accuracy of the inclination recorded by sedimentary rocks is crucial to paleogeographic reconstructions. Laboratory compaction experiments show that inclination shallows on the order of 10˚-15˚. Corrections to the inclination can be made using the effects of compaction on the directional distribution of secular variation recorded by sediments or the anisotropy of the magnetic grains carrying the ancient remanence. A summary of all the compaction correction studies as of 2012 shows that 85% of sedimentary rocks studied have enjoyed some amount of inclination shallowing. Future work should also consider the effect of grain-scale strain on paleomagnetic remanence. High resolution chronostratigraphy can be assigned to a sedimentary sequence using rock magnetics to detect astronomically-forced climate cycles. The power of the technique is relatively quick, non-destructive measurements, the objective identification of the cycles compared to facies interpretations, and the sensitivity of rock magnetics to subtle changes in sedimentary source. An example of this technique comes from using rock magnetics to identify astronomically-forced climate cycles in three globally distributed occurrences of the Shuram carbon isotope excursion. The Shuram excursion may record the oxidation of the world ocean in the Ediacaran, just before the Cambrian explosion of metazoans. Using rock magnetic cyclostratigraphy, the excursion is shown to have the same duration (8-9 Myr) in southern California, south China and south Australia. Magnetostratigraphy of the rocks carrying the excursion in California and Australia shows a reversed to normal geomagnetic field polarity transition at the excursion's nadir, thus supporting the synchroneity of the excursion globally. Both results point to a

Rock mass mechanical property estimations for the Yucca Mountain Site Characterization Project

International Nuclear Information System (INIS)

Lin, M.; Hardy, M.P.; Bauer, S.J.

1993-06-01

Rock mass mechanical properties are important in the design of drifts and ramps. These properties are used in evaluations of the impacts of thermomechanical loading of potential host rock within the Yucca Mountain Site Characterization Project. Representative intact rock and joint mechanical properties were selected for welded and nonwelded tuffs from the currently available data sources. Rock mass qualities were then estimated using both the Norwegian Geotechnical Institute (Q) and Geomechanics Rating (RMR) systems. Rock mass mechanical properties were developed based on estimates of rock mass quality, the current knowledge of intact properties, and fracture/joint characteristics. Empirical relationships developed to correlate the rock mass quality indices and the rock mass mechanical properties were then used to estimate the range of rock mass mechanical properties

Experimental Characterization of Stress- and Strain-Dependent Stiffness in Grouted Rock Masses

Directory of Open Access Journals (Sweden)

Ji-Won Kim

2018-03-01

Full Text Available Grouting of fractured rock mass prior to excavation results in grout-filled discontinuities that govern the deformation characteristics of a site. The influence of joint characteristics on the properties of grouted rocks is important in assessing the effects of grouting on jointed rock mass. However, grouting remains a predominantly empirical practice and the effects of grouting on rock joint behavior and material properties have yet to be accurately assessed. Granular materials, including jointed rocks, typically display nonlinear strain-dependent responses that can be characterized by the shear modulus degradation curve. In this study, the effects of grouting on the strain-dependent shear stiffness of jointed rock mass were investigated at the small-strain (below 10−5 and mid-strain (10−5 to 10−3 ranges using the quasi-static resonant column test and rock mass dynamic test devices. The effects of curing time, axial stress, initial joint roughness, and grouted joint thickness were examined. The results show that (1 grouting of rock joints leads to decreased stress sensitivity and increased small-strain shear stiffness for all tested samples; (2 the grouted rock samples display similar modulus degradation characteristics as the applied grout material; (3 the initial joint roughness determines the stress-dependent behaviors and general stiffness range of the jointed and grouted rocks, but the strain-dependent behaviors are dependent on the properties of the grout material; (4 increased grouted joint thickness results in larger contribution of the grout properties in the overall grouted rock mass.

Mineralogical, chemical and K-Ar isotopic changes in Kreyenhagen Shale whole rocks and <2 µm clay fractions during natural burial and hydrous-pyrolysis experimental maturation

Science.gov (United States)

Clauer, Norbert; Lewan, Michael D.; Dolan, Michael P.; Chaudhuri, Sambhudas; Curtis, John B.

2014-01-01

Progressive maturation of the Eocene Kreyenhagen Shale from the San Joaquin Basin of California was studied by combining mineralogical and chemical analyses with K–Ar dating of whole rocks and sequence, indicating that there is no detectable variation in the crystallo-chemical organization of the K-bearing alumino-silicates with depth. No supply of K from outside of the rock volumes occurred, which indicates a closed-system behavior for it. Conversely, the content of the total organic carbon (TOC) content decreases significantly with burial, based on the progressive increasing Al/TOC ratio of the whole rocks. The initial varied mineralogy and chemistry of the rocks and their <2 μm fractions resulting from differences in detrital sources and depositional settings give scattered results that homogenize progressively during burial due to increased authigenesis, and concomitant increased alteration of the detrital material.

Remarks on some rock neutron parameters

International Nuclear Information System (INIS)

Czubek, J.A.

1984-01-01

A method to calculate the thermal neutron parameters of rocks is given in the paper. It is based on a proper energy averaging of cross-sections for all rock matrix and rock saturating liquid constituents. The diffusion lengths in different lithologies in function of the variable rock porosity have been calculated. An influence of the thermal neutron spectrum on the shape of the porosity calibration curves for the dual spacing neutron method is shown. Magmatic rocks as a possible source of geothermal energy are now becoming a target of neutron loggings for the porosity determination. Here the knowledge of the slowing-down lengths is of great importance in the problem of the estimation of the calibration curves. A semi-analytical approach to get this parameter is given in the paper. It was found, as far as concerns the slowing-down of fast neutrons, that all magmatic rocks behave as sandstone with, however, different content of bound water in the rock matrix and different rock matrix density. Some neutron methods are based on the detection of epithermal neutrons. For theoretical considerations it is important to know the physical meaning of the registered signal. From the discussion of experimental data reported in the literature it seems that it is the slowing-down density that is the physical quantity being measured. This conclusion has a very important practical implication - the porosity calibration curves depend upon the slowing-down length alone and are independent of the slowing-down cross-section for epithermal neutrons

Studies on the radiation absorption characteristics of various rocks

International Nuclear Information System (INIS)

Rahman, K.N.; Abdullah, S.A.; Gazzaz, M.A.

1984-05-01

Radiation absorption characteristics of nine different rocks, namely, ferrugenous quartz, metabasalt, larvikite, coarse grained diorite, coarse grained granite, coarse grained alkali granite, marble, quartz mica schist, and metamorphosed rock are studied. The rocks were collected from Jeddah, Makkah, Mina and Taif areas. Special attention was given on the availability, compactness, physical formation and uniform composition in selecting the rocks. The rocks were identified by optical method and their elemental composition determined by chemical analysis. The data were used to calculate the effective atomic numbers, half value layers mass and linear attenuation coefficients. The half value layers and the linear attenuation coefficientsof these rocks were determined experimentally using Am-241, Cs-137,and Co-60 sources. The results are compared with those obtained by theoretical calculations and agrre within 10%. Most of the rocks show much higher radiation attenuation characteristics than the standard concrete. Rocks containing higher percentage of Fe, Ca, Ti, and Mn show much higher radiation absorption characteristics than concrete. Only granites are found to be almost equivalent to concrete. 12 Ref

HEAVY MINERALS IN PLACER DEPOSIT IN SINGKAWANG WATERS, WEST Kalimantan, RELATED TO FELSIC SOURCE ROCK OF ITS COASTAL AREA

Directory of Open Access Journals (Sweden)

Deny Setiady

2017-07-01

Full Text Available Placer deposits are physically accumulated by fluvial and marine processes in coastal area. Thirty six samples were selected from seventy seven samples of seafloor sediment of Singkawang waters. Those samples have been analyzed microscopically for heavy mineral contents. Based on this analysis, the heavy minerals can be divided into four groups: oxyde and hydroxyde, silicate, sulphide, and carbonate. The source of most heavy minerals in the study area is commonly formed by Felsic igneous rock and finally deposited on the seafloor sediments.

Perfect zircon for rock dating no fairy tale

International Nuclear Information System (INIS)

Anon

2000-01-01

The scheme used to date rocks is based on the radioactive decay of uranium. Minute traces of uranium locked inside the zircon crystals have been decaying over aeons, producing lead. Scientists know that the decay occurs at a fixed rate and how quickly it happens. By measuring the relative amounts of uranium and lead encased in the crystals, scientists can determine how old the rock is. But sometimes lead is lost from zircon crystals via processes such as weathering (if the rocks were exposed on the surface) or deformation and metamorphism (if the rocks had crystallised deep in the earth and been subjected to high temperatures and pressure). Hence the special nature of the Temora rocks- a 417 million years old zirconium-containing rock which have been partially exposed in recent times in a remote paddock in NSW, Australia. SHRIMP dating was used for initial tests on the Temora rocks. Then, in December last year, the sample was sent to the world-recognised authority, Canada's Royal Ontario Museum, for independent analysis and dating via chemical decomposition. The museum confirmed the near perfect quality of the zircon and its age

U-Pb ages and Hf isotope compositions of zircons in plutonic rocks from the central Famatinian arc, Argentina

Science.gov (United States)

Otamendi, Juan E.; Ducea, Mihai N.; Cristofolini, Eber A.; Tibaldi, Alina M.; Camilletti, Giuliano C.; Bergantz, George W.

2017-07-01

The Famatinian arc formed around the South Iapetus rim during the Ordovician, when oceanic lithosphere subducted beneath the West Gondwana margin. We present combined in situ U-Th-Pb and Lu-Hf isotope analyses for zircon to gain insights into the origin and evolution of Famatinian magmatism. Zircon crystals sampled from four intermediate and silicic plutonic rocks confirm previous observations showing that voluminous magmatism took place during a relatively short pulse between the Early and Middle Ordovician (472-465 Ma). The entire zircon population for the four plutonic rocks yields coherent εHf negative values and spreads over several ranges of initial εHf(t) units (-0.3 to -8.0). The range of εHf units in detrital zircons of Famatinian metasedimentary rocks reflects a prolonged history of the cratonic sources during the Proterozoic to the earliest Phanerozoic. Typical tonalites and granodiorites that contain zircons with evolved Hf isotopic compositions formed upon incorporating (meta)sedimentary materials into calc-alkaline metaluminous magmas. The evolved Hf isotope ratios of zircons in the subduction related plutonic rocks strongly reflect the Hf isotopic character of the metasedimentary contaminant, even though the linked differentiation and growth of the Famatinian arc crust was driven by ascending and evolving mantle magmas. Geochronology and Hf isotope systematics in plutonic zircons allow us understanding the petrogenesis of igneous series and the provenance of magma sources. However, these data could be inadequate for computing model ages and supporting models of crustal evolution.

Drill-back studies examine fractured, heated rock

International Nuclear Information System (INIS)

Wollenberg, H.A.; Flexser, S.; Myer, L.R.

1990-01-01

To investigate the effects of heating on the mineralogical, geochemical, and mechanical properties of rock by high-level radioactive waste, cores are being examined from holes penetrating locations where electric heaters simulated the presence of a waste canister, and from holes penetration natural hydrothermal systems. Results to date indicate the localized mobility and deposition of uranium in an open fracture in heated granitic rock, the mobility of U in a breccia zone in an active hydrothermal system in tuff, and the presence of U in relatively high concentration in fracture-lining material in tuff. Mechanical -- property studies indicate that differences in compressional- and shear-wave parameters between heated and less heated rock can be attributed to differences in the density of microcracks. Emphasis has shifted from initial studies of granitic rock at Stripa, Sweden to current investigations of welded tuff at the Nevada Test Site. 7 refs., 8 figs

Recent advances in acceleration of source iterations for fixed-source slab-geometry S{sub N} calculations based on P{sub N} synthetic initial guess

Energy Technology Data Exchange (ETDEWEB)

Guida, Mateus Rodrigues; Alves Filho, Hermes; Barros, Ricardo C., E-mail: mguida@iprj.uerj.br, E-mail: halves@iprj.uerj.br, E-mail: rcbarros@pq.cnpq.br [Universidade do Estado do Rio de Janeiro (UERJ), Nova Friburgo, RJ (Brazil). Instituto Politecnico. Programa de Pos-Graduacao em Modelagem Computacional

2015-07-01

The scattering source iterative (SI) scheme is applied traditionally to converge fine-mesh numerical solutions to fixed-source discrete ordinates (S{sub N}) neutron transport problems with linearly anisotropic scattering. The SI scheme is very simple to implement under a computational viewpoint. However, the SI scheme may show very slow convergence rate, mainly for diffusive media (low absorption) with several mean free paths in extent. In this work we describe two acceleration techniques based on improved initial guesses for the SI scheme, wherein we initialize the scattering source distribution within the slab using the P{sub 1} and P{sub 3} approximations. In order to estimate these initial guesses, we use the coarse-mesh solution of the PN equations with special boundary conditions to account for the classical S{sub N} prescribed boundary conditions, including vacuum boundary conditions. To apply this coarse-mesh P{sub N} solution for the accelerated scheme, we first perform within-node spatial reconstruction, and then we determine the fine-mesh average scalar flux and total current for initializing the linearly anisotropic scattering source terms for the SI scheme. We consider a number of numerical experiments to illustrate the efficiency of the offered P{sub N} synthetic acceleration (P{sub N}SA) technique based on initial guess. (author)

Tensile rock mass strength estimated using InSAR

KAUST Repository

Jonsson, Sigurjon

2012-11-01

The large-scale strength of rock is known to be lower than the strength determined from small-scale samples in the laboratory. However, it is not well known how strength scales with sample size. I estimate kilometer-scale tensional rock mass strength by measuring offsets across new tensional fractures (joints), formed above a shallow magmatic dike intrusion in western Arabia in 2009. I use satellite radar observations to derive 3D ground displacements and by quantifying the extension accommodated by the joints and the maximum extension that did not result in a fracture, I put bounds on the joint initiation threshold of the surface rocks. The results indicate that the kilometer-scale tensile strength of the granitic rock mass is 1–3 MPa, almost an order of magnitude lower than typical laboratory values.

Tensile rock mass strength estimated using InSAR

KAUST Repository

Jonsson, Sigurjon

2012-01-01

The large-scale strength of rock is known to be lower than the strength determined from small-scale samples in the laboratory. However, it is not well known how strength scales with sample size. I estimate kilometer-scale tensional rock mass strength by measuring offsets across new tensional fractures (joints), formed above a shallow magmatic dike intrusion in western Arabia in 2009. I use satellite radar observations to derive 3D ground displacements and by quantifying the extension accommodated by the joints and the maximum extension that did not result in a fracture, I put bounds on the joint initiation threshold of the surface rocks. The results indicate that the kilometer-scale tensile strength of the granitic rock mass is 1–3 MPa, almost an order of magnitude lower than typical laboratory values.

17,21-Secohopanoic acids, 25-norhopanoic acids, and 28-norhopanoic acids in source rocks and crude oils

Energy Technology Data Exchange (ETDEWEB)

Xueming Pan; Philp, R.P. [University of Oklahoma, Norman, OK (United States). School of Geology and Geophysics

2006-09-15

The presence of three families of hopanoic acids, 17,21-secohopanoic acids, 25-norhopanoic acids, and 28-norhopanoic acids, is discussed. Oils from West Siberia and tar balls from the Seychelles Islands were found to contain relatively high proportions of 17,21-secohopanoic acids. These acids have not been previously reported in any oils or source rocks. A heavily biodegraded West Siberian oil, was found to contain an homologous series of 25-norhopanoic acids co-occurring with the 25-norhopanes as previously reported in only a small number of oils from Campos Basin, Brazil. 28-Norhopanoic acids have been reported in various sediments and extracts of the Monterey Shale, but in this study their occurrence has been extended to oils, degraded oils, and tar balls sourced from the Monterey Shale. The primary purpose herein is to report the occurrence of these acids and possible relationships between the acids and corresponding hydrocarbons. (Author)

Microscopic study of rock for estimating long-term behavior

International Nuclear Information System (INIS)

Ichikawa, Yasuaki

2002-03-01

Micro-structure of rock plays a essential role for their long-term behavior. For elucidating long-term characteristics of granite we here present the followings: 1) Conforcal Laser Scanning Microscope (LSM) observation of joint surfaces of granite and Fourier analysis, 2) characterization of the mechanism of microcrack initiation and propagation observed by stereoscopic microscope under uniaxial/triaxial compression and relaxation tests, 3) observation of microcrack initiation and propagation by LSM under uniaxial compression, and 4) a viscoelastic homogenization theory to predict the long-term behavior of micro/macro-level stress for granite. Rock image processing and analysis become a fundamental procedure to determine rock surface discontinuities. But the complexity of rock surface discontinuities seems beyond the manual image processing method. In Chapter 2 a Conforcal Laser Scanning Microscope that can acquire three-dimensional images is introduced to observe the rock roughness of a discontinuity. Then, scanning three-dimensional images are changed its data form in order to adapt various image analysis programs, and granitic rock roughness of discontinuities are displayed by graphic images. For example, these datas are analyzed by Discrete Fourier Transformation (DFT) program and Inverse Discrete Fourier Transformation (IDFT) program. Microcrack generation and propagation play an essential role to predict the long-term behavior of rock. In Chapter 3 a progressive development of cracking in granite is revealed by using stereoscopic microscope under triaxial compression condition and by using LSM under uniaxial compression condition. With a viscoelastic theory applied in homogenization method, we can calculate macro behavior of medium influenced by its micro structure by analyse the long-term time-dependent behavior of granite under the same condition to the relaxation experiment. (author)

Sr isotopes in natural waters: Applications to source characterisation and water-rock interaction in contrasting landscapes

International Nuclear Information System (INIS)

Shand, P.; Darbyshire, D.P.F.; Love, A.J.; Edmunds, W.M.

2009-01-01

Strontium isotopes ( 87 Sr/ 86 Sr) are routinely measured in hydrochemical studies to determine sources and mixing relationships. They have proved particularly useful in determining weathering processes and quantifying end-member mixing processes. A number of routine case studies are presented which highlight that Sr isotopes represent a powerful tool in the geochemists toolbox helping to constrain weathering reactions, weathering rates, flow pathways and mixing scenarios. Differences in methodologies for determining the weathering component in natural environments, inherent differences in weathering rates of different minerals, and mineral heterogeneity often cause difficulties in defining the weathering component of different catchments or aquifer systems. Nevertheless, Sr isotopes are useful when combined with other hydrochemical data, to constrain models of water-rock interaction and mixing as well as geochemical processes such as ion-exchange. This paper presents a summary of recent work by the authors in constraining the sources of waters and weathering processes in surface catchments and aquifers, and indicates cases where Sr isotopes alone are insufficient to solve hydrological problems.

Sr isotopes in natural waters: Applications to source characterisation and water-rock interaction in contrasting landscapes

Energy Technology Data Exchange (ETDEWEB)

Shand, P., E-mail: paul.shand@csiro.au [CSIRO Land and Water/CRC LEME, Private Bag 2, Glen Osmond, SA 5064 (Australia); Darbyshire, D.P.F. [NERC Isotope Geosciences Laboratory, Kingsley Dunham Centre, Keyworth, Nottingham NG12 5GG (United Kingdom); Love, A.J. [Department of Water, Land and Biodiversity Conservation, P.O. Box 2843, Adelaide 5001 (Australia); Edmunds, W.M. [School of Geography, Oxford University Centre for the Environment, South Parks Road, Oxford (United Kingdom)

2009-04-15

Strontium isotopes ({sup 87}Sr/{sup 86}Sr) are routinely measured in hydrochemical studies to determine sources and mixing relationships. They have proved particularly useful in determining weathering processes and quantifying end-member mixing processes. A number of routine case studies are presented which highlight that Sr isotopes represent a powerful tool in the geochemists toolbox helping to constrain weathering reactions, weathering rates, flow pathways and mixing scenarios. Differences in methodologies for determining the weathering component in natural environments, inherent differences in weathering rates of different minerals, and mineral heterogeneity often cause difficulties in defining the weathering component of different catchments or aquifer systems. Nevertheless, Sr isotopes are useful when combined with other hydrochemical data, to constrain models of water-rock interaction and mixing as well as geochemical processes such as ion-exchange. This paper presents a summary of recent work by the authors in constraining the sources of waters and weathering processes in surface catchments and aquifers, and indicates cases where Sr isotopes alone are insufficient to solve hydrological problems.

Isotopic assessment of soil phosphorus fertility and evaluation of rock phosphates as phosphorus sources for plants in subtropical China

International Nuclear Information System (INIS)

Xiong, L.M.; Zhou, Z.G.; Feng, G.L.; Lu, R.K.; Fardeau, J.C.

2002-01-01

Soil phosphorus (P) deficiency is a major factor limiting crop productivity in many tropical and subtropical soils. Due to the acidic nature of these soils, rock phosphate (RP)-based P fertilizers that are cheaper than manufactured water-soluble P fertilizers can be an attractive alternative under certain conditions. Assessment of the efficacy of these alternative P fertilizers and a rational management of local P resources for sustainable agricultural production require an understanding of the dynamics of P in the soil-plant system and the interactions of various P sources in soils and monitoring of soil available P levels. The present work was conducted to test the applicability of the 32 P isotopic kinetic method to assess the soil P fertility status and evaluate the agronomic effectiveness of local rock phosphates in subtropical China. A series of experiments was carried out in the laboratory, greenhouse and field conditions with the following specific objectives: (a) to evaluate the suitability of this isotopic kinetic method in evaluating soil P fertility in 32 soil samples collected across southern China, (b) to test and further develop chemical extraction methods for routine soil P testing, (c) to monitor the dissolution kinetics of local low to medium grade rock phosphate sources and their effect on soil properties and (d) to evaluate their agronomic effectiveness in greenhouse and field experiments. Since most of the studied soils had very low concentrations of soluble P and high P-fixing capacities, the isotopic kinetic method was found unsuitable for evaluating soil P fertility and to predict plant P uptake. In contrast, the proposed chemical extraction method (NaHCO 3 -NH 4 F) predicted very well plant P uptake, suggesting that this extraction method can be routinely used to evaluate soil bioavailable P in similar soils in subtropical China. From the incubation study, it was found that although the local low to medium grade RPs were inferior to the

Experimental Studies on the Mechanical Behaviour of Rock Joints with Various Openings

Science.gov (United States)

Li, Y.; Oh, J.; Mitra, R.; Hebblewhite, B.

2016-03-01

The mechanical behaviour of rough joints is markedly affected by the degree of joint opening. A systematic experimental study was conducted to investigate the effect of the initial opening on both normal and shear deformations of rock joints. Two types of joints with triangular asperities were produced in the laboratory and subjected to compression tests and direct shear tests with different initial opening values. The results showed that opened rock joints allow much greater normal closure and result in much lower normal stiffness. A semi-logarithmic law incorporating the degree of interlocking is proposed to describe the normal deformation of opened rock joints. The proposed equation agrees well with the experimental results. Additionally, the results of direct shear tests demonstrated that shear strength and dilation are reduced because of reduced involvement of and increased damage to asperities in the process of shearing. The results indicate that constitutive models of rock joints that consider the true asperity contact area can be used to predict shear resistance along opened rock joints. Because rock masses are loosened and rock joints become open after excavation, the model suggested in this study can be incorporated into numerical procedures such as finite-element or discrete-element methods. Use of the model could then increase the accuracy and reliability of stability predictions for rock masses under excavation.

Thermal Inertia of Rocks and Rock Populations

Science.gov (United States)

Golombek, M. P.; Jakosky, B. M.; Mellon, M. T.

2001-01-01

The effective thermal inertia of rock populations on Mars and Earth is derived from a model of effective inertia versus rock diameter. Results allow a parameterization of the effective rock inertia versus rock abundance and bulk and fine component inertia. Additional information is contained in the original extended abstract.

Studying physical properties of deformed intact and fractured rocks by micro-scale hydro-mechanical-seismicity model

Science.gov (United States)

Raziperchikolaee, Samin

The pore pressure variation in an underground formation during hydraulic stimulation of low permeability formations or CO2 sequestration into saline aquifers can induce microseismicity due to fracture generation or pre-existing fracture activation. While the analysis of microseismic data mainly focuses on mapping the location of fractures, the seismic waves generated by the microseismic events also contain information for understanding of fracture mechanisms based on microseismic source analysis. We developed a micro-scale geomechanics, fluid-flow and seismic model that can predict transport and seismic source behavior during rock failure. This model features the incorporation of microseismic source analysis in fractured and intact rock transport properties during possible rock damage and failure. The modeling method considers comprehensive grains and cements interaction through a bonded-particle-model. As a result of grain deformation and microcrack development in the rock sample, forces and displacements in the grains involved in the bond breakage are measured to determine seismic moment tensor. In addition, geometric description of the complex pore structure is regenerated to predict fluid flow behavior of fractured samples. Numerical experiments are conducted for different intact and fractured digital rock samples, representing various mechanical behaviors of rocks and fracture surface properties, to consider their roles on seismic and transport properties of rocks during deformation. Studying rock deformation in detail provides an opportunity to understand the relationship between source mechanism of microseismic events and transport properties of damaged rocks to have a better characterizing of fluid flow behavior in subsurface formations.

Eo-Oligocene Oil Shales of the Talawi, Lubuktaruk, and Kiliranjao Areas, West Sumatra: Are they potential source rocks?

Directory of Open Access Journals (Sweden)

M. Iqbal

2014-12-01

Full Text Available DOI:10.17014/ijog.v1i3.198To anticipate the increasing energy demand, additional data and information covering unconventional fossil fuels such as oil shale must be acquired to promote the usage of alternative energy sources to crude oil. The Talawi and Lubuktaruk regions situated within intra-montane Ombilin Basin, and the Kiliranjao assumed to be a small intra montane basin are occupied by Eo-Oligocene sediments of Sangkarewang and Kiliran Formations, respectively. Field activity, geochemical screening techniques, and organic petrographic analysis, supported by SEM mode, are methods used. Most of the oil shale sequence is typically of an organically rich-succession comprising predominantly well-bedded, laminated and fissile, brownish to dark grey organic-rich shale and mudstone rocks. The exinite macerals within oil shale comprise mainly Pediastrum-lamalginite with minor cutinite, resinite, liptodetrinite, sporinite, bituminite, and rare Botryococcus-telalginite. Therefore; the oil shale deposits can be described as “lamosites”. Minor vitrinite maceral is also recognized. TOC analysis on selected shale samples corresponds to a fair up to excellent category of source rock characterization. The hydrogen index (HI for all samples shows a range of values from 207 - 864, and pyrolysis yield (PY ranges from 2.67 to 79.72 mg HC/g rock. The kerogen is suggested to be of mixed Type II and Type I autochthonous materials such as alginite, with minor allochthonous substances. Oil samples collected appear to be positioned within more oil prone rather than gas prone. Thermal maturity of the oil shales gained from Tmax value and production index (PI tends to show immature to marginally/early mature stage. A consistency in the thermal maturity level results by using both Tmax and vitrinite reflectance value is recognized. On the basis of  SEM analysis, the oil shale has undergone a late eodiagenetic process. Thereby, overall, vitrinite reflectance

Modeling tectonic heat flow and source rock maturity in the Rub' Al-Khali Basin (Saudi Arabia), with the help of GOCE satellite gravity data

NARCIS (Netherlands)

Abdul Fattah, R.; Meekes, S.; Bouman, J.; Ebbing, J.; Haagmans, R.

2014-01-01

A 3D basin modeling study was carried out to reconstruct the regional heat flow and source rock maturity in the Rub'al-Khali basin. Gravity gradient data from the GOCE satellite were used to model deep structures, such as the Moho interface. Tectonic heat flow was modeled using the GOCE-based Moho

Lidar-Based Rock-Fall Hazard Characterization of Cliffs

Science.gov (United States)

Collins, Brian D.; Greg M.Stock,

2017-01-01

Rock falls from cliffs and other steep slopes present numerous challenges for detailed geological characterization. In steep terrain, rock-fall source areas are both dangerous and difficult to access, severely limiting the ability to make detailed structural and volumetric measurements necessary for hazard assessment. Airborne and terrestrial lidar survey methods can provide high-resolution data needed for volumetric, structural, and deformation analyses of rock falls, potentially making these analyses straightforward and routine. However, specific methods to collect, process, and analyze lidar data of steep cliffs are needed to maximize analytical accuracy and efficiency. This paper presents observations showing how lidar data sets should be collected, filtered, registered, and georeferenced to tailor their use in rock fall characterization. Additional observations concerning surface model construction, volumetric calculations, and deformation analysis are also provided.

Rock disposal problems identified

Energy Technology Data Exchange (ETDEWEB)

Knox, R

1978-06-01

Mathematical models are the only way of examining the return of radioactivity from nuclear waste to the environment over long periods of time. Work in Britain has helped identify areas where more basic data is required, but initial results look very promising for final disposal of high level waste in hard rock repositories. A report by the National Radiological Protection Board of a recent study, is examined.

Nd and Sr isotopic variations in acidic rocks from Japan: significance of upper-mantle heterogeneity

Science.gov (United States)

Terakado, Yasutaka; Nakamura, Noboru

1984-10-01

Initial Nd and Sr isotopic ratios have been measured for Cretaceous acidic and related intermediate rocks (24 volcanic and two plutonic rocks) from the Inner Zone of Southwest Japan (IZSWJ) to investigate the genesis of acidic magmas. The initial Nd and Sr isotopic ratios for these rocks show three interesting features: (1) ɛ Nd values for acidic rocks (+2 to -9) are negatively correlated with ɛ Sr values (+10 to +90) together with those for intermediate rocks ( ɛ Nd=+3 to -8; ɛ Sr=0 to +65). (2) The ɛ Nd values for silica rich rocks (>60% SiO2) correlate with the longitude of the sample locality, decreasing from west to east in a stepwise fashion: Four areas characterized by uniform ɛ Nd values are discriminated. (3) Low silica rocks (Japan suggest that the acidic rocks can be formed neither by fractional crystallization processes from more basic magmas nor by crustal assimilation processes. The isotopic variations of the acidic rocks may reflect regional isotopic heterogeneity in the lower crust, and this heterogeneity may ultimately be attributed to the regional heterogeneity of the uppermost-mantle beneath the Japanese Islands.

Geochemical evaluation of Pabdeh Formation in Nosrat field, southeast Persian Gulf using Rock- Eval VI pyrolysis

Directory of Open Access Journals (Sweden)

mohammad sadeghi

2015-02-01

Full Text Available The present study was performed on 59 drillhole cuttings from Pabdeh Formation in Nosrat oil field using Rock- Eval VI pryrolysis. Geochemical analysis indicated that Pabdeh Formation possesses poor to good hydrocarbon potential. Plotting S1 against TOC suggests that samples were not affected by polluting substances such as crude oil and lubricants while drilling operation. Jones organic fancies diagram shows B-BC area indicating that Pabdeh Formation was deposited in marine anoxic to oxic environments. HI vesus Tmax shows that most samples initially have had type II kerogen and now reflecting a mixture of type II to III kerogen (capable of generating oil that have already entered oil generation window. In addition, S1+S2 versus TOC plot also suggests that Pabdeh Formation can be considered as a capable hydrocarbon generating source rock in the study area.

Rock-fall Hazard In The Yosemite Valley, California

Science.gov (United States)

Guzzetti, F.; Reichenbach, P.; Wieczorek, G. F.

Rock slides and rock falls are the most frequent slope movements in Yosemite Na- tional Park, California. In historical time (1851-2001), more than 400 rock falls and rock slides have been documented in the valley, and some of them have been mapped in detail. We present the preliminary results of an attempt to assess rockfall hazard in the Yosemite Valley using STONE, a 3-dimensional rock-fall simulation computer program. The software computes 3-dimensional rock-fall trajectories starting from a digital terrain model (DTM), the location of rock-fall release points (source areas), and maps of the dynamic rolling coefficient and of the coefficients of normal and tan- gential energy restitution. For each DTM cell the software also calculates the number of rock falls passing through the cell, the maximum rock-fall velocity and the maxi- mum flying height. For the Yosemite Valley, a DTM with a ground resolution of 10 x 10 m was prepared using topographic contour lines from USGS 1:24,000-scale maps. Rock-fall release points were identified as DTM cells having a slope steeper than 60 degrees, an assumption based on the location of historical rock falls. Maps of the nor- mal and tangential energy restitution coefficients and of the rolling friction coefficient were produced from a surficial geologic map. The availability of historical rock falls mapped in detail allowed us to check the computer program performance and to cali- brate the model parameters. Visual and statistical comparison of the model results with the mapped rock falls confirmed the accuracy of the model. The model results are also compared with a geomorphic assessment of rock-fall hazard based on potential energy referred to as a "shadow angle" approach, recently completed for the Yosemite Valley.

Self-Healing Characteristics of Damaged Rock Salt under Different Healing Conditions

Directory of Open Access Journals (Sweden)

Lin Li

2013-08-01

Full Text Available Salt deposits are commonly regarded as ideal hosts for geologic energy reservoirs. Underground cavern construction-induced damage in salt is reduced by self-healing. Thus, studying the influencing factors on such healing processes is important. This research uses ultrasonic technology to monitor the longitudinal wave velocity variations of stress-damaged rock salts during self-recovery experiments under different recovery conditions. The influences of stress-induced initial damage, temperature, humidity, and oil on the self-recovery of damaged rock salts are analyzed. The wave velocity values of the damaged rock salts increase rapidly during the first 200 h of recovery, and the values gradually increase toward stabilization after 600 h. The recovery of damaged rock salts is subjected to higher initial damage stress. Water is important in damage recovery. The increase in temperature improves damage recovery when water is abundant, but hinders recovery when water evaporates. The presence of residual hydraulic oil blocks the inter-granular role of water and restrains the recovery under triaxial compression. The results indicate that rock salt damage recovery is related to the damage degree, pore pressure, temperature, humidity, and presence of oil due to the sealing integrity of the jacket material.

Metamorphic Rock-Hosted Orogenic Gold Deposit Type as a Source of Langkowala Placer Gold, Bombana, Southeast Sulawesi

Directory of Open Access Journals (Sweden)

Arifudin Idrus

2014-06-01

Full Text Available DOI: 10.17014/ijog.v6i1.114In 2008, placer gold was discovered in Langkowala area (Bombana Regency, Southeast Sulawesi, Indonesia, and more than 60,000 traditional gold miners in the early 2009 have been operating by digging vertical pits and panning active stream sediments. The grade of placer gold ranges from 50 to 140 g/t. Local geological framework indicates that the placer gold is not related to volcanic rock-related hydrothermal gold deposit, e.g. epithermal, skarn or porphyry. This paper describes a preliminary study on possible primary deposit type as a source of the Langkowala (Bombana secondary placer gold. A field study indicates that the Langkowala (Bombana placer/paleoplacer gold is possibly related to gold-bearing quartz veins/veinlets hosted by metamorphic rocks particularly mica schist and metasediments in the area. These quartz veins/veinlets are currently recognized in metamorphic rocks at Wumbubangka Mountains, a northern flank of Rumbia Mountain Range. Sheared, segmented quartz veins/veinlets are of 2 cm to 2 m in width and contain gold in a grade varying between 2 and 61 g/t. At least, there are two generations of the quartz veins. The first generation of quartz vein is parallel to foliation of mica schist and metasediments with general orientation of N 300oE/60o; the second quartz vein generation crosscut the first quartz vein and the foliation of the wallrock. The first quartz veins are mostly sheared/deformed, brecciated, and occasionally sigmoidal, whereas the second quartz veins are relatively massive. The similar quartz veins/veinlets types are also probably present in Mendoke Mountain Range, in the northern side of Langkowala area. This primary gold deposit is called as ‘orogenic gold type’. The orogenic gold deposit could be a new target of gold exploration in Indonesia in the future.

Rock-brine chemical interactions. Final report

Energy Technology Data Exchange (ETDEWEB)

1982-02-01

The results of experimental interaction of powdered volcanic rock with aqueous solutions are presented at temperatures from 200 to 400/sup 0/C, 500 to 1000 bars fluid pressure, with reaction durations of approximately 30 days under controlled laboratory conditions. The aim of this research is to develop data on the kinetics and equilibria of rock solution interactions that will provide insight into the complex geochemical processes attending geothermal reservoir development, stimulation, and reinjection. The research was done in the Stanford Hydrothermal Lab using gold cell equipment of the Dickson design. This equipment inverts the solution rock mixture several times a minute to ensure thorough mixing. Solution samples were periodically withdrawn without interruption of the experimental conditions. The data from these experiments suggests a path dependent series of reactions by which geothermal fluids might evolve from meteoric or magmatic sources.

The participatory archive of the sites of Danish rock music culture

DEFF Research Database (Denmark)

Knudsen, Line Vestergaard

History” as an example of such a digital participatory archive. This digital online project is initiated by the Danish Rock Music Museum and intends to gather material that portray the sites’ and meeting places’ (such as venues, festivals, youth clubs etc.) of Danish rock music culture. Danish rock music......When setting out to tell the story of rock music culture, one approach is a focus at the “meeting places” where bands, fans and those behind the scenes have gathered. With this approach the cultural heritage of rock music becomes situated and site-specific, and it is nearby to think of ways...... to engage those who “inhabited” these specific sites of the previous 60 years of rock music culture. This paper will discuss how the issues of locality and rock music culture can be gathered and researched by a participatory (web 2.0) archive. The research is empirically focused at “The Map of Danish Rock...

Acoustic emission measurements in petroleum-related rock mechanics

Energy Technology Data Exchange (ETDEWEB)

Unander, Tor Erling

2002-07-01

Acoustic emission activity in rock has usually been studied in crystalline rock, which reflects that rock mechanics has also mostly been occupied with such rocks in relations to seismology, mining and tunneling. On the other hand, petroleum-related rock mechanics focuses on the behaviour of sedimentary rock. Thus, this thesis presents a general study of acoustic emission activity in sedimentary rock, primarily in sandstone. Chalk, limestone and shale have also been tested, but to much less degree because the AE activity in these materials is low. To simplify the study, pore fluids have not been used. The advent of the personal computer and computerized measuring equipment have made possible new methods both for measuring and analysing acoustic emissions. Consequently, a majority of this work is devoted to the development and implementation of new analysis techniques. A broad range of topics are treated: (1) Quantification of the AE activity level, assuming that the event rate best represents the activity. An algorithm for estimating the event rate and a methodology for objectively describing special changes in the activity e.g., onset determination, are presented. (2) Analysis of AE waveform data. A new method for determining the source energy of an AE event is presented, and it is shown how seismic source theory can be used to analyze even intermediate quality data. Based on these techniques, it is shown that a major part of the measured AE activity originates from a region close to the sensor, not necessarily representing the entire sample. (3) An improved procedure for estimating source locations is presented. The main benefit is a procedure that better handles arrival time data with large errors. Statistical simulations are used to quantify the uncertainties in the locations. The analysis techniques are developed with the application to sedimentary rock in mind, and in two articles, the techniques are used in the study of such materials. The work in the first

Rock pushing and sampling under rocks on Mars

Science.gov (United States)

Moore, H.J.; Liebes, S.; Crouch, D.S.; Clark, L.V.

1978-01-01

Viking Lander 2 acquired samples on Mars from beneath two rocks, where living organisms and organic molecules would be protected from ultraviolet radiation. Selection of rocks to be moved was based on scientific and engineering considerations, including rock size, rock shape, burial depth, and location in a sample field. Rock locations and topography were established using the computerized interactive video-stereophotogrammetric system and plotted on vertical profiles and in plan view. Sampler commands were developed and tested on Earth using a full-size lander and surface mock-up. The use of power by the sampler motor correlates with rock movements, which were by plowing, skidding, and rolling. Provenance of the samples was determined by measurements and interpretation of pictures and positions of the sampler arm. Analytical results demonstrate that the samples were, in fact, from beneath the rocks. Results from the Gas Chromatograph-Mass Spectrometer of the Molecular Analysis experiment and the Gas Exchange instrument of the Biology experiment indicate that more adsorbed(?) water occurs in samples under rocks than in samples exposed to the sun. This is consistent with terrestrial arid environments, where more moisture occurs in near-surface soil un- der rocks than in surrounding soil because the net heat flow is toward the soil beneath the rock and the rock cap inhibits evaporation. Inorganic analyses show that samples of soil from under the rocks have significantly less iron than soil exposed to the sun. The scientific significance of analyses of samples under the rocks is only partly evaluated, but some facts are clear. Detectable quantities of martian organic molecules were not found in the sample from under a rock by the Molecular Analysis experiment. The Biology experiments did not find definitive evidence for Earth-like living organisms in their sample. Significant amounts of adsorbed water may be present in the martian regolith. The response of the soil

Excess europium content in Precambrian sedimentary rocks and continental evolution

Science.gov (United States)

Jakes, P.; Taylor, S. R.

1974-01-01

It is proposed that the europium excess in Precambrian sedimentary rocks, relative to those of younger age, is derived from volcanic rocks of ancient island arcs, which were the source materials for the sediments. Precambrian sedimentary rocks and present-day volcanic rocks of island arcs have similar REE patterns, total REE abundances, and excess Eu, relative to the North American shale composite. The present upper crustal REE pattern, as exemplified by that of sediments, is depleted in Eu, relative to chondrites. This depletion is considered to be a consequence of development of a granodioritic upper crust by partial melting in the lower crust, which selectively retains europium.

The Source Inversion Validation (SIV) Initiative: A Collaborative Study on Uncertainty Quantification in Earthquake Source Inversions

Science.gov (United States)

Mai, P. M.; Schorlemmer, D.; Page, M.

2012-04-01

Earthquake source inversions image the spatio-temporal rupture evolution on one or more fault planes using seismic and/or geodetic data. Such studies are critically important for earthquake seismology in general, and for advancing seismic hazard analysis in particular, as they reveal earthquake source complexity and help (i) to investigate earthquake mechanics; (ii) to develop spontaneous dynamic rupture models; (iii) to build models for generating rupture realizations for ground-motion simulations. In applications (i - iii), the underlying finite-fault source models are regarded as "data" (input information), but their uncertainties are essentially unknown. After all, source models are obtained from solving an inherently ill-posed inverse problem to which many a priori assumptions and uncertain observations are applied. The Source Inversion Validation (SIV) project is a collaborative effort to better understand the variability between rupture models for a single earthquake (as manifested in the finite-source rupture model database) and to develop robust uncertainty quantification for earthquake source inversions. The SIV project highlights the need to develop a long-standing and rigorous testing platform to examine the current state-of-the-art in earthquake source inversion, and to develop and test novel source inversion approaches. We will review the current status of the SIV project, and report the findings and conclusions of the recent workshops. We will briefly discuss several source-inversion methods, how they treat uncertainties in data, and assess the posterior model uncertainty. Case studies include initial forward-modeling tests on Green's function calculations, and inversion results for synthetic data from spontaneous dynamic crack-like strike-slip earthquake on steeply dipping fault, embedded in a layered crustal velocity-density structure.

Technological plasma source equipped with combined system of vacuum-arc discharge initiation

International Nuclear Information System (INIS)

Sysoev, Yu.O.

2013-01-01

The construction and the operation principle of erosion plasma source with a three-stage system of vacuum-arc discharge excitation is described. As first two step was used the modified contactless start system with plasma injector, which was widely used in standard plasma sources of the ''Bulat'' systems. The operation principle of the third stage was based on the transition of glow discharge to arc discharge. Coordinated operation of three stages during various stages of coating deposition provided significant increasing of service life and reliability of the system of vacuum-arc discharge initiation and extended the functionality of the plasma source

Uranium occurrence in major rock types by fission-track mapping

International Nuclear Information System (INIS)

Ledger, E.G.; Bomber, B.J.; Schaftenaar, W.E.; Tieh, T.T.

1984-01-01

Microscopic occurrence of uranium has been determined in about 50 igneous rocks from various location, and in a genetically unrelated sandstone from south Texas. Precambrian granites from the Llano uplift of central Texas contain from a few ppm uranium (considered normal) to over 100 ppm on a whole-rock basis. In granite, uranium is concentrated in: (1) accessory minerals including zircon, biotite, allanite, Fe-Ti oxides, and altered sphene, (2) along grain boundaries and in microfractures by precipitation from deuteric fluids, and (3) as point sources (small inclusions) in quartz and feldspars. Tertiary volcanic rocks from the Davis Mountains of west Texas include diverse rock types from basalt to rhyolite. Average uranium contents increase from 1 ppm in basalts to 7 ppm in rhyolites. Concentration occurs: (1) in iron-titanium-oxides, zircon, and rutile, (2) in the fine-grained groundmass as uniform and point-source concentrations, and (3) as late uranium in cavities associated with banded, silica-rich material. Uranium in ore-grade sandstone is concentrated to more than 3%. Specific occurrences include (1) leucoxene and/or anatase, (2) opaline and calcite cements, (3) mud clasts and altered volcanic rock fragments, and (4) in a few samples, as silt-size uranium- and molybdenum-rich spheres. Uranium content is quite low in pyrite, marcasite, and zeolites

Tectono-thermal Evolution of the Lower Paleozoic Petroleum Source Rocks in the Southern Lublin Trough: Implications for Shale Gas Exploration from Maturity Modelling

Science.gov (United States)

Botor, Dariusz

2018-03-01

The Lower Paleozoic basins of eastern Poland have recently been the focus of intensive exploration for shale gas. In the Lublin Basin potential unconventional play is related to Lower Silurian source rocks. In order to assess petroleum charge history of these shale gas reservoirs, 1-D maturity modeling has been performed. In the Łopiennik IG-1 well, which is the only well that penetrated Lower Paleozoic strata in the study area, the uniform vitrinite reflectance values within the Paleozoic section are interpreted as being mainly the result of higher heat flow in the Late Carboniferous to Early Permian times and 3500 m thick overburden eroded due to the Variscan inversion. Moreover, our model has been supported by zircon helium and apatite fission track dating. The Lower Paleozoic strata in the study area reached maximum temperature in the Late Carboniferous time. Accomplished tectono-thermal model allowed establishing that petroleum generation in the Lower Silurian source rocks developed mainly in the Devonian - Carboniferous period. Whereas, during Mesozoic burial, hydrocarbon generation processes did not develop again. This has negative influence on potential durability of shale gas reservoirs.

Loading-unloading pressure-volume curves for rocks

International Nuclear Information System (INIS)

Stephens, D.R.; Lilley, E.M.

1970-01-01

The stress-strain codes (SOC and TENSOR) used to calculate phenomenology of nuclear explosion for the Plowshare Program require inter alia the pressure-volume relationships of the earth media. In this paper we describe a rapid and accurate method to obtain pressure-volume data to 40 kb at 25 deg. C for rocks. These experimental results may also be related to the in situ elastic properties of the rock and to other laboratory measurement of properties, such as ultrasonic experiments with pressure and Hugoniot determinations. Qualitative features of the pressure-volume curves can be related to the initial porosity of the rock. A porous rock is usually quite compressible at low pressures. If the porosity is in the form of narrow cracks, the cracks are closed at a pressure of about 3 to 6 kb, after which the rock is much less compressible. If the porosity is in the form of spherical pores, it is not necessarily removed even at pressures of 40 kb, depending on the strength of the rock, and the compressibility is higher at all pressures than for a similar rock containing no porosity. Data for water-saturated samples show the phase transformation due to free water at about 10 and 22 kb. However, the presence of 'nonliquid' water, which is loosely contained within the lattice of clay or zeolitic minerals or adsorbed on particle surfaces, is also observed. (author)

Loading-unloading pressure-volume curves for rocks

Energy Technology Data Exchange (ETDEWEB)

Stephens, D R; Lilley, E M [Lawrence Radiation Laboratory, University of California, Livermore, CA (United States)

1970-05-01

The stress-strain codes (SOC and TENSOR) used to calculate phenomenology of nuclear explosion for the Plowshare Program require inter alia the pressure-volume relationships of the earth media. In this paper we describe a rapid and accurate method to obtain pressure-volume data to 40 kb at 25 deg. C for rocks. These experimental results may also be related to the in situ elastic properties of the rock and to other laboratory measurement of properties, such as ultrasonic experiments with pressure and Hugoniot determinations. Qualitative features of the pressure-volume curves can be related to the initial porosity of the rock. A porous rock is usually quite compressible at low pressures. If the porosity is in the form of narrow cracks, the cracks are closed at a pressure of about 3 to 6 kb, after which the rock is much less compressible. If the porosity is in the form of spherical pores, it is not necessarily removed even at pressures of 40 kb, depending on the strength of the rock, and the compressibility is higher at all pressures than for a similar rock containing no porosity. Data for water-saturated samples show the phase transformation due to free water at about 10 and 22 kb. However, the presence of 'nonliquid' water, which is loosely contained within the lattice of clay or zeolitic minerals or adsorbed on particle surfaces, is also observed. (author)

Modeling of nuclear waste disposal by rock melting

International Nuclear Information System (INIS)

Heuze, F.E.

1982-04-01

Today, the favored option for disposal of high-level nuclear wastes is their burial in mined caverns. As an alternative, the concept of deep disposal by rock melting (DRM) also has received some attention. DRM entails the injection of waste, in a cavity or borehole, 2 to 3 kilometers down in the earth crust. Granitic rocks are the prime candidate medium. The high thermal loading initially will melt the rock surrounding the waste. Following resolidification, a rock/waste matrix is formed, which should provide isolation for many years. The complex thermal, mechanical, and hydraulic aspects of DRM can be studied best by means of numerical models. The models must accommodate the coupling of the physical processes involved, and the temperature dependency of the granite properties, some of which are subject to abrupt discontinuities, during α-β phase transition and melting. This paper outlines a strategy for such complex modeling

Shear-flow coupling in non-planar rock joints

International Nuclear Information System (INIS)

Makurat, A.; Barton, N.

1985-01-01

Crystalline rock masses are regarded as a possible host rock for permanent nuclear waste disposal. During the excavation of the required shafts and tunnels, the initial state of stress will be changed and cause a deformation of the rock mass and discontinuities. During the lifetime of the nuclear repository joint apertures may change due to thermally induced stress variations during the heating and cooling phase. As the conductivity of a joint is very sensitive to its aperture, fluid flow from and towards a repository, as well as the potential transport times of radionuclides are highly dependent on the deformability of the joints. Theoretical calculations of coupled flow in rock joints (Barton et al. 1984) predict an increase of conductivity of several orders of magnitude for the first few millimeters for shear displacement. The shear-dilation-conductivity coupling for two block sizes at two effective stress levels is shown

Strength Restoration of Cracked Sandstone and Coal under a Uniaxial Compression Test and Correlated Damage Source Location Based on Acoustic Emissions

Science.gov (United States)

Feng, Xiaowei; Zhang, Nong; Zheng, Xigui; Pan, Dongjiang

2015-01-01

Underground rock masses have shown a general trend of natural balance over billions of years of ground movement. Nonetheless, man-made underground constructions disturb this balance and cause rock stability failure. Fractured rock masses are frequently encountered in underground constructions, and this study aims to restore the strength of rock masses that have experienced considerable fracturing under uniaxial compression. Coal and sandstone from a deep-buried coal mine were chosen as experimental subjects; they were crushed by uniaxial compression and then carefully restored by a chemical adhesive called MEYCO 364 with an innovative self-made device. Finally, the restored specimens were crushed once again by uniaxial compression. Axial stress, axial strain, circumferential strain, and volumetric strain data for the entire process were fully captured and are discussed here. An acoustic emission (AE) testing system was adopted to cooperate with the uniaxial compression system to provide better definitions for crack closure thresholds, crack initiation thresholds, crack damage thresholds, and three-dimensional damage source locations in intact and restored specimens. Several remarkable findings were obtained. The restoration effects of coal are considerably better than those of sandstone because the strength recovery coefficient of the former is 1.20, whereas that of the latter is 0.33, which indicates that MEYCO 364 is particularly valid for fractured rocks whose initial intact peak stress is less than that of MEYCO 364. Secondary cracked traces of restored sandstone almost follow the cracked traces of the initial intact sandstone, and the final failure is mainly caused by decoupling between the adhesive and the rock mass. However, cracked traces of restored coal only partially follow the traces of intact coal, with the final failure of the restored coal being caused by both bonding interface decoupling and self-breakage in coal. Three-dimensional damage source

Strength Restoration of Cracked Sandstone and Coal under a Uniaxial Compression Test and Correlated Damage Source Location Based on Acoustic Emissions.

Directory of Open Access Journals (Sweden)

Xiaowei Feng

Full Text Available Underground rock masses have shown a general trend of natural balance over billions of years of ground movement. Nonetheless, man-made underground constructions disturb this balance and cause rock stability failure. Fractured rock masses are frequently encountered in underground constructions, and this study aims to restore the strength of rock masses that have experienced considerable fracturing under uniaxial compression. Coal and sandstone from a deep-buried coal mine were chosen as experimental subjects; they were crushed by uniaxial compression and then carefully restored by a chemical adhesive called MEYCO 364 with an innovative self-made device. Finally, the restored specimens were crushed once again by uniaxial compression. Axial stress, axial strain, circumferential strain, and volumetric strain data for the entire process were fully captured and are discussed here. An acoustic emission (AE testing system was adopted to cooperate with the uniaxial compression system to provide better definitions for crack closure thresholds, crack initiation thresholds, crack damage thresholds, and three-dimensional damage source locations in intact and restored specimens. Several remarkable findings were obtained. The restoration effects of coal are considerably better than those of sandstone because the strength recovery coefficient of the former is 1.20, whereas that of the latter is 0.33, which indicates that MEYCO 364 is particularly valid for fractured rocks whose initial intact peak stress is less than that of MEYCO 364. Secondary cracked traces of restored sandstone almost follow the cracked traces of the initial intact sandstone, and the final failure is mainly caused by decoupling between the adhesive and the rock mass. However, cracked traces of restored coal only partially follow the traces of intact coal, with the final failure of the restored coal being caused by both bonding interface decoupling and self-breakage in coal. Three

Favorability for uranium in tertiary sedimentary rocks, southwestern Montana

International Nuclear Information System (INIS)

Wopat, M.A.; Curry, W.E.; Robins, J.W.; Marjaniemi, D.K.

1977-10-01

Tertiary sedimentary rocks in the basins of southwestern Montana were studied to determine their favorability for potential uranium resources. Uranium in the Tertiary sedimentary rocks was probably derived from the Boulder batholith and from silicic volcanic material. The batholith contains numerous uranium occurrences and is the most favorable plutonic source for uranium in the study area. Subjective favorability categories of good, moderate, and poor, based on the number and type of favorable criteria present, were used to classify the rock sequences studied. Rocks judged to have good favorability for uranium deposits are (1) Eocene and Oligocene strata and undifferentiated Tertiary rocks in the western Three Forks basin and (2) Oligocene rocks in the Helena basin. Rocks having moderate favorability consist of (1) Eocene and Oligocene strata in the Jefferson River, Beaverhead River, and lower Ruby River basins, (2) Oligocene rocks in the Townsend and Clarkston basins, (3) Miocene and Pliocene rocks in the Upper Ruby River basin, and (4) all Tertiary sedimentary formations in the eastern Three Forks basin, and in the Grasshopper Creek, Horse Prairie, Medicine Lodge Creek, Big Sheep Creek, Deer Lodge, Big Hole River, and Bull Creek basins. The following have poor favorability: (1) the Beaverhead Conglomerate in the Red Rock and Centennial basins, (2) Eocene and Oligocene rocks in the Upper Ruby River basin, (3) Miocene and Pliocene rocks in the Townsend, Clarkston, Smith River, and Divide Creek basins, (4) Miocene through Pleistocene rocks in the Jefferson River, Beaverhead River, and Lower Ruby River basins, and (5) all Tertiary sedimentary rocks in the Boulder River, Sage Creek, Muddy Creek, Madison River, Flint Creek, Gold Creek, and Bitterroot basins

Ultrapotassic rocks geology from Salgueiro region, Pernambuco state, Brazil

International Nuclear Information System (INIS)

Silva Filho, A.F. da; Guimaraes, I.P.

1990-01-01

The Cachoeirinha-Salgueiro belt has Proterozoic age and is located in the Borborema Province, NE Brazil. The ultrapotassic rocks from Salgueiro region intrudes the Cachoeirinha-Salgueiro belt rocks. The ultrapotassics from Salgueiro region constitutes of three units; Serra do Livramento pluton, and two dyke swarms called respectively beige alkali feldspar granites and green alkali feldspar syenite/quartz-syenite. The Serra do Livramento pluton shows E-W direction, boudin shape, width between 0,15 and 2,10 km, and it is intruded into metamorphic rocks and into the Terra Nova complex. Detailed geological mapping at the Serra das Duas Irmas allowed us to establish the dyke swarm chronology. The mapping reveals seven intrusion episodes, into the Terra Nova pluton, of green alkali feldspar syenite/quartz-syenite and five episodes of bege alkali feldspar granite. They alternate between them in space and time, and there are evidence that they were intruded under the tectonic control of the Pernambuco lineament. A systematic whole-rock Rb-Sr geochronology was done in the green alkali feldspar syenite/quartz-syenite, and an age of 514,8 ± 20,3 Ma was obtained. The initial ratio is 0,710615 + 0,000441. The age obtained shows small error and an initial ratio compatible with a strong crustal contamination. (author)

Finding Funding: A Guide to Federal Sources for Asset-Building Initiatives. Finding Funding Series

Science.gov (United States)

Lind, Christianne; Relave, Nanette; Schmid, William; Terzaghi, Damon

2009-01-01

This guide outlines strategies for financing asset-building initiatives and provides information on 71 federal funding sources that can be used to support a range of activities and services. It includes well-known sources of funding for asset building, for example, the Assets for Independence Demonstration Program and the Family Self-Sufficiency…

Detrital Zircons From the Jack Hills and Mount Narryer, Western Australia: Geochronological, Morphological, and Geochemical Evidence for Diverse >4000 Ma Source Rocks

Science.gov (United States)

Crowley, J. L.; Myers, J. S.; Sylvester, P. J.; Cox, R. A.

2004-05-01

Detrital zircons from all major clastic units in the Jack Hills and Mount Narryer metasedimentary belts, Western Australia, were analyzed for morphology, internal zoning, inclusion mineralogy, age, and trace element concentrations (latter two obtained by laser-ablation microprobe ICPMS). The results show that zircons were derived from a wide diversity of rocks, including previously described, >4000 Ma grains that are older than any known terrestrial rocks. In three metaconglomerate samples from the western Jack Hills, 4200-3800 Ma zircons ("old grains") comprise 14% of the population, 3800-3600 Ma grains form only 2%, and 3550-3250 Ma zircons ("young grains") are dominant with a significant peak at 3380 Ma. Old and young grains are interpreted as being from similar rock types because they are indistinguishable in trace element concentrations, size (several hundred microns), morphology (subequant, typically fragmented), internal zoning (typically both oscillatory and sector), and U concentration (50-200 ppm). Many of these properties suggest an intermediate plutonic source, whereas an evolved granitic source was previously interpreted from rare-earth element and oxygen isotope data. Detrital zircons in quartzites and metaconglomerates at Mount Narryer differ significantly from zircons from the western Jack Hills. Old grains comprise only 3% (most of which are 4200-4100 Ma), 3800-3600 Ma zircons form 31%, and there are peaks at 3650, 3600, and 3500 Ma. Old and young grains have similar properties that suggest granitic sources, such as elongate prismatic morphology, oscillatory zoning, high U concentrations (100-600 ppm), and xenotime and monazite inclusions. Trace element concentrations are broadly similar to those in Jack Hills zircons, with notable exceptions being generally higher U, smaller Ce and Eu anomalies, and lower Nb/Ta. It is considered unlikely that Jack Hills zircons were derived from granitic gneisses that surround the metasedimentary belts because

The problem of extracting oil from bituminous rock

Energy Technology Data Exchange (ETDEWEB)

Liatifov, A.I.; Bagirov, M.K.; Shirinov, S.G.; Sokov, U.I.; Zhirnov, E.I.

1982-01-01

Results are given from experimental laboratory research on flushing bituminous sandstones using diesel or oil alkaline by-products as the flushing agent and a sodium silicate solution as the desensitization initiator for the rock.

Field studies on two rock phosphate solubilizing actinomycete isolates as biofertilizer sources

Science.gov (United States)

Mba, Caroline C.

1994-03-01

Recently biotechnology is focusing attention on utilization of biological resources to solve a number of environmental problems such as soil fertility management. Results of microbial studies on earthworm compost in the University of Nigeria farm identified a number of rock phosphate solubilizing actinomycetes. Two of these, isclates 02 and 13, were found to be efficient rock phosphate (RP) solubilizers and fast-growing cellulolytic microbes producing extracellular hydrolase enzymes. In this preliminary field study the two microbial isolates were investigated with respect to their effects on the growth of soybean and egusi as well as their effect on the incidence of toxicity of poultry droppings. Application of these isolates in poultry manure-treated field plots, as microbial fertilizers, brought about yield increases of 43% and 17% with soybeans and 19% and 33% with egusi, respectively. Soil properties were also improved. With isolates 02 and 13, the soil available phosphorus increased at the five-leaf stage, while N-fixation in the soil increased by 45% or 11% relative to control. It was further observed that air-dried poultry manure after four days of incubation was still toxic to soybean. The toxic effect of the applied poultry manure was reduced or eliminated with microbial fertilizers 02 or 13, respectively. The beneficial effects of the microbial organic fertilizer are discussed. Justification for more intensive research on rock phosphate organic fertilizer is highlighted.

Structure analysis - chiromancy of the rock

International Nuclear Information System (INIS)

Huber, A.; Huber, M.

1989-01-01

The reader may initially be surprised by a comparison between structure analysis and palmistry which is, in effect, a comparison between a scientific research method on the one hand and art which is equated with magical powers on the other. In the figurative sense, however, these two fields have some points in common which should help us to obtain a first impression of the nature of geological structure analysis. Chiromancy uses the lines and the form of the hand to predict the character and the future of the person in question. In the same way, geologists use rocks and rock forms to obtain information on structure and behaviour of different formations. Structure analysis is a specialised field of geological investigation in which traces of deformation are interpreted as expressions of rockforming forces. This article discusses how and why the character of a rock formation as well as its past, present and even future behaviour can be determined using structure analysis. (author) 11 figs

Isotopic data bearing on the origin of Mesozoic and Tertiary granitic rocks in the western United States

International Nuclear Information System (INIS)

DePaolo, D.J.; Farmer, G.L.

1984-01-01

A regional survey of initial Nd and Sr isotopic compositions has been done on Mesozoic and Tertiary granitic rocks from a 500 000 km 2 area in California, Nevada, Utah, Arizona, and Colorado. The plutons, which range in composition from quartz diorite to monzogranite, are intruded into accreted oceanic geosynclinal terrains in the west and north and into Precambrian basement in the east. Broad geographic coverage allows the data to be interpreted in the context of the regional pre-Mesozoic crustal structure. Initial Nd isotopic compositions exhibit a huge range, encompassing values typical of oceanic magmatic arcs and Archean basement. The sources of the magmas can be inferred from the systematic geographic variability of Nd isotopic compositions. The plutons in the accreted terrains represent mantle-derived magma that assimilated crust while differentiating at deep levels. Those emplaced into Precambrian basement are mainly derived from the crust. The regional patterns can be understood in terms of: (1) the flux of mantle magma entering the crust; (2) crustal thickness; and (3) crustal age. The mantle magma flux apparently decreased inland; in the main batholith belts purely crustal granitic rocks are not observed because the flux was too large. Inland, crustal granite is common because mantle magma was scarce and the crust was thick, and hot enough to melt. The epsilonsub(Nd) values of peraluminous granite formed by melting of the Precambrian basement depend on the age of the local basement source. (author)

Development of soda-lime glasses from ornamental rock wastes

International Nuclear Information System (INIS)

Babisk, Michelle Pereira

2009-01-01

During the ornamental rocks production, among other steps, one saw the rock blocks in order to transform them into semi-finished plates. In this step, expressive amounts of residues are generated, which are not properly discharged in nature, without any programmed utilization. The residues of silicide rocks present, in their compositions, oxides which are raw materials employed to fabricate soda-lime type glasses (containing SiO_2, Al_2O_3, CaO, Na_2O and K_2O). On the other hand the residues of carbonatic rocks are constituted of glass net modifier oxides, like CaO and MgO. In this work it was developed four types of soda-lime glasses using ornamental rock residues, where the glasses compositions were adjusted by adding sand, as silica source, as well as sodium and calcium carbonates as sources of Na_2O and CaO, respectively. The obtained glasses were characterized by means of Archimed's method for densities measurements, microstructure by using optical and electronic microscopy, phases by means of X-ray diffraction (XRD), hardness by Vickers indentation, spectroscopy (UV/VIS), and hydrolytic resistance according to ISO 719. The XRD analyses confirmed the compositions total vitrification, where the greened aspect of the samples was due to the presence of the iron oxides. The produced glasses properties were compared with those of commercial glasses aiming their industrial employment. The main difference between the produced glasses and those commercials varied primarily regarding the amount of carbonates incorporated. The results showed that the ornamental rocks residues may be used as raw materials for glasses fabrication, and they found a useful economic destination rather than discharge which promotes undesirable environmental impact. (author)

Size Effect on Acoustic Emission Characteristics of Coal-Rock Damage Evolution

Directory of Open Access Journals (Sweden)

Zhijie Wen

2017-01-01

Full Text Available Coal-gas outburst, rock burst, and other mine dynamic disasters are closely related to the instability and failure of coal-rock. Coal-rock is the assemblies of mineral particles of varying sizes and shapes bonded together by cementing materials. The damage and rupture process of coal-rock is accompanied by acoustic emission (AE, which can be used as an effective means to monitor and predict the instability of coal-rock body. In this manuscript, considering the size effect of coal-rock, the influence of different height to diameter ratio on the acoustic emission characteristics of coal-rock damage evolution was discussed by microparticle flow PFC2D software platform. The results show that coal-rock size influences the uniaxial compressive strength, peak strain, and elastic modulus of itself; the size effect has little effect on the acoustic emission law of coal-rock damage and the effects of the size of coal-rock samples on acoustic emission characteristics are mainly reflected in three aspects: the triggering time of acoustic emission, the strain range of strong acoustic emission, and the intensity of acoustic emission; the damage evolution of coal-rock specimen can be divided into 4 stages: initial damage, stable development, accelerated development, and damage.

Estimating the Wet-Rock P-Wave Velocity from the Dry-Rock P-Wave Velocity for Pyroclastic Rocks

Science.gov (United States)

Kahraman, Sair; Fener, Mustafa; Kilic, Cumhur Ozcan

2017-07-01

Seismic methods are widely used for the geotechnical investigations in volcanic areas or for the determination of the engineering properties of pyroclastic rocks in laboratory. Therefore, developing a relation between the wet- and dry-rock P-wave velocities will be helpful for engineers when evaluating the formation characteristics of pyroclastic rocks. To investigate the predictability of the wet-rock P-wave velocity from the dry-rock P-wave velocity for pyroclastic rocks P-wave velocity measurements were conducted on 27 different pyroclastic rocks. In addition, dry-rock S-wave velocity measurements were conducted. The test results were modeled using Gassmann's and Wood's theories and it was seen that estimates for saturated P-wave velocity from the theories fit well measured data. For samples having values of less and greater than 20%, practical equations were derived for reliably estimating wet-rock P-wave velocity as function of dry-rock P-wave velocity.

Search for underground openings for in situ test facilities in crystalline rock

Energy Technology Data Exchange (ETDEWEB)

Wollenberg, H.A.; Strisower, B.; Corrigan, D.J.; Graf, A.N.; O' Brien, M.T.; Pratt, H.; Board, M.; Hustrulid, W.

1980-01-01

With a few exceptions, crystalline rocks in this study were limited to plutonic rocks and medium to high-grade metamorphic rocks. Nearly 1700 underground mines, possibly occurring in crystalline rock, were initially identified. Application of criteria resulted in the identification of 60 potential sites. Within this number, 26 mines and 4 civil works were identified as having potential in that they fulfilled the criteria. Thirty other mines may have similar potential. Most of the mines identified are near the contact between a pluton and older sedimentary, volcanic and metamorphic rocks. However, some mines and the civil works are well within plutonic or metamorphic rock masses. Civil works, notably underground galleries associated with pumped storage hydroelectric facilities, are generally located in tectonically stable regions, in relatively homogeneous crystalline rock bodies. A program is recommended which would identify one or more sites where a concordance exists between geologic setting, company amenability, accessibility and facilities to conduct in situ tests in crystalline rock.

Search for underground openings for in situ test facilities in crystalline rock

International Nuclear Information System (INIS)

Wollenberg, H.A.; Strisower, B.; Corrigan, D.J.; Graf, A.N.; O'Brien, M.T.; Pratt, H.; Board, M.; Hustrulid, W.

1980-01-01

With a few exceptions, crystalline rocks in this study were limited to plutonic rocks and medium to high-grade metamorphic rocks. Nearly 1700 underground mines, possibly occurring in crystalline rock, were initially identified. Application of criteria resulted in the identification of 60 potential sites. Within this number, 26 mines and 4 civil works were identified as having potential in that they fulfilled the criteria. Thirty other mines may have similar potential. Most of the mines identified are near the contact between a pluton and older sedimentary, volcanic and metamorphic rocks. However, some mines and the civil works are well within plutonic or metamorphic rock masses. Civil works, notably underground galleries associated with pumped storage hydroelectric facilities, are generally located in tectonically stable regions, in relatively homogeneous crystalline rock bodies. A program is recommended which would identify one or more sites where a concordance exists between geologic setting, company amenability, accessibility and facilities to conduct in situ tests in crystalline rock

Petrology of lunar rocks and implication to lunar evolution

Science.gov (United States)

Ridley, W. I.

1976-01-01

Recent advances in lunar petrology, based on studies of lunar rock samples available through the Apollo program, are reviewed. Samples of bedrock from both maria and terra have been collected where micrometeorite impact penetrated the regolith and brought bedrock to the surface, but no in situ cores have been taken. Lunar petrogenesis and lunar thermal history supported by studies of the rock sample are discussed and a tentative evolutionary scenario is constructed. Mare basalts, terra assemblages of breccias, soils, rocks, and regolith are subjected to elemental analysis, mineralogical analysis, trace content analysis, with studies of texture, ages and isotopic composition. Probable sources of mare basalts are indicated.

'Escher' Rock

Science.gov (United States)

2004-01-01

[figure removed for brevity, see original site] Chemical Changes in 'Endurance' Rocks [figure removed for brevity, see original site] Figure 1 This false-color image taken by NASA's Mars Exploration Rover Opportunity shows a rock dubbed 'Escher' on the southwestern slopes of 'Endurance Crater.' Scientists believe the rock's fractures, which divide the surface into polygons, may have been formed by one of several processes. They may have been caused by the impact that created Endurance Crater, or they might have arisen when water leftover from the rock's formation dried up. A third possibility is that much later, after the rock was formed, and after the crater was created, the rock became wet once again, then dried up and developed cracks. Opportunity has spent the last 14 sols investigating Escher, specifically the target dubbed 'Kirchner,' and other similar rocks with its scientific instruments. This image was taken on sol 208 (Aug. 24, 2004) by the rover's panoramic camera, using the 750-, 530- and 430-nanometer filters. The graph above shows that rocks located deeper into 'Endurance Crater' are chemically altered to a greater degree than rocks located higher up. This chemical alteration is believed to result from exposure to water. Specifically, the graph compares ratios of chemicals between the deep rock dubbed 'Escher,' and the more shallow rock called 'Virginia,' before (red and blue lines) and after (green line) the Mars Exploration Rover Opportunity drilled into the rocks. As the red and blue lines indicate, Escher's levels of chlorine relative to Virginia's went up, and sulfur down, before the rover dug a hole into the rocks. This implies that the surface of Escher has been chemically altered to a greater extent than the surface of Virginia. Scientists are still investigating the role water played in influencing this trend. These data were taken by the rover's alpha particle X-ray spectrometer.

IODP Expedition 351 Lithostratigraphy: Volcaniclastic Record of Izu-Bonin-Mariana (IBM) Arc Initiation

Science.gov (United States)

Barth, A. P.; Brandl, P. A.; Li, H.; Hickey-Vargas, R.; Jiang, F.; Kanayama, K.; Kusano, Y.; Marsaglia, K. M.; McCarthy, A.; Meffre, S.; Savov, I. P.; Tepley, F. J., III; Yogodzinski, G. M.

2014-12-01

The destruction of lithospheric plates by subduction is a fundamentally important process leading to arc magmatism and the creation of continental crust, yet subduction initiation and early magmatic arc evolution remain poorly understood. For many arc systems, onset of arc volcanism and early evolution are obscured by metamorphism or the record is deeply buried; however, initial products of arc systems may be preserved in forearc and backarc sedimentary records. IODP Expedition 351 recovered this history from the dispersed ash and pyroclast record in the proximal rear-arc of the northern IBM system west of the Kyushu-Palau Ridge. Drilling at Site U1438 in the Amami Sankaku Basin recovered a thick volcaniclastic record of subduction initiation and the early evolution of the Izu-Bonin Arc. A 160-m thick section of Neogene sediment overlies 1.3 kilometers of Paleogene volcaniclastic rocks with andesitic average composition; this volcaniclastic section was deposited on mafic volcanic basement rocks. The thin upper sediment layer is primarily terrigenous, biogenic and volcaniclastic mud and ooze with interspersed ash layers. The underlying Eocene to Oligocene volcaniclastic rocks are 33% tuffaceous mudstone, 61% tuffaceous sandstone, and 6% conglomerate with volcanic and rare sedimentary clasts commonly up to pebble and rarely to cobble size. The clastic section is characterized by repetitive conglomerate and sandstone-dominated intervals with intervening mudstone-dominated intervals, reflecting waxing and waning of coarse arc-derived sediment inputs through time. Volcanic lithic clasts in sandstones and conglomerates range from basalt to rhyolite in composition and include well-preserved pumice, reflecting a lithologically diverse and compositionally variable arc volcanic source.

Geochemical constraints on the petrogenesis of the pyroclastic rocks in Abakaliki basin (Lower Benue Rift), Southeastern Nigeria

Science.gov (United States)

Chukwu, Anthony; Obiora, Smart C.

2018-05-01

The pyroclastic rocks in the Cretaceous Abakaliki basin occur mostly as oval-shaped bodies, consisting of lithic/lava and vitric fragments. They are commonly characterized by parallel and cross laminations, as well contain xenoliths of shale, mudstone and siltstones from the older Asu River Group of Albian age. The rocks are basic to ultrabasic in composition, comprising altered alkali basalts, altered tuffs, minor lapillistones and agglomerates. The mineral compositions are characterized mainly by laths of calcic plagioclase, pyroxene (altered), altered olivines and opaques. Calcite, zeolite and quartz represent the secondary mineral constituents. Geochemically, two groups of volcaniclastic rocks, are distinguished: alkaline and tholeiitic rocks, both represented by fresh and altered rock samples. The older alkali basalts occur within the core of the Abakaliki anticlinorium while the younger tholeiites occur towards the periphery. Though most of the rocks are moderate to highly altered [Loss on ignition (LOI, 3.43-22.07 wt. %)], the use of immobile trace element such as Nb, Zr, Y, Hf, Ti, Ta and REEs reflect asthenospheric mantle source compositions. The rocks are enriched in incompatible elements and REEs (∑REE = 87.98-281.0 ppm for alkaline and 69.45-287.99 ppm for tholeiites). The ratios of La/Ybn are higher in the alkaline rocks ranging from 7.69 to 31.55 compared to the tholeiitic rocks which range from 4.4 to 16.89 and indicating the presence of garnet-bearing lherzolite in the source mantle. The spidergrams and REEs patterns along with Zr/Nb, Ba/Nb, Rb/Nb ratios suggest that the rocks were generated by a mantle plume from partial melting of mixed enriched mantle sources (HIMU, EMI and EMII) similar to the rocks of the south Atlantic Ocean such as St. Helena (alkaline rocks) and Ascension rocks (tholeiitic rocks). The rocks were formed in a within-plate setting of the intra-continental rift type similar to other igneous rocks in the Benue Rift and are not

The Rock Characterization Facility

International Nuclear Information System (INIS)

Holmes, J.

1994-01-01

In 1989, UK Nirex began a programme of surface-based characterization of the geology and hydrogeology of a site at Sellafield to evaluate its suitability to host a deep repository for radioactive waste. The next major stage in site characterization will be the construction and operation of a Rock Characterization Facility (RCF). It will be designed to provide rock characterization information and scope for model validation to permit firmer assessment of long-term safety. It will also provide information needed to decide the detailed location, design and orientation of a repository and to inform repository construction methods. A three-phase programme is planned for the RCF. During each phase, testwork will steadily improve our geological, hydrogeological and geotechnical understanding of the site. The first phase will involve sinking two shafts. That will be preceded by the establishment of a network of monitoring boreholes to ensure that the impact of shaft sinking can be measured. This will provide valuable data for model validation. In phase two, initial galleries will be excavated, probably at a depth of 650 m below Ordnance datum, which will host a comprehensive suite of experiments. These galleries will be extended in phase three to permit access to most of the rock volume that would host the repository. (Author)

Catalytic generation of methane at 60-100 °C and 0.1-300 MPa from source rocks containing kerogen Types I, II, and III

Science.gov (United States)

Wei, Lin; Schimmelmann, Arndt; Mastalerz, Maria; Lahann, Richard W.; Sauer, Peter E.; Drobniak, Agnieszka; Strąpoć, Dariusz; Mango, Frank D.

2018-06-01

Low temperature (60 and 100 °C) and long-term (6 months to 5 years) heating of pre-evacuated and sterilized shales and coals containing kerogen Types I (Mahogany Shale), II (Mowry Shale and New Albany Shale), and III (Springfield Coal and Wilcox Lignite) with low initial maturities (vitrinite reflectance Ro 0.39-0.62%) demonstrates that catalytically generated hydrocarbons may explain the occurrence of some non-biogenic natural gas accumulations where insufficient thermal maturity contradicts the conventional thermal cracking paradigm. Extrapolation of the observed rate of catalytic methanogenesis in the laboratory suggests that significant amounts of sedimentary organic carbon can be converted to relatively dry natural gas over tens of thousands of years in sedimentary basins at temperatures as low as 60 °C. Our laboratory experiments utilized source rock (shale and coal) chips sealed in gold and Pyrex® glass tubes in the presence of hydrogen-isotopically contrasting waters. Parallel heating experiments applied hydrostatic pressures from 0.1 to 300 MPa. Control experiments constrained the influence of pre-existing and residual methane in closed pores of rock chips that was unrelated to newly generated methane. This study's experimental methane yields at 60 and 100 °C are 5-11 orders of magnitude higher than the theoretically predicted yields from kinetic models of thermogenic methane generation, which strongly suggests a contribution of catalytic methanogenesis. Higher temperature, longer heating time, and lower hydrostatic pressure enhanced catalytic methanogenesis. No clear relationships were observed between kerogen type or total organic carbon content and methane yields via catalysis. Catalytic methanogenesis was strongest in Mowry Shale where methane yields at 60 °C amounted to ∼2.5 μmol per gram of organic carbon after one year of hydrous heating at ambient pressure. In stark contrast to the earlier findings of hydrogen isotopic exchange between

Osmium Isotope Compositions of Komatiite Sources Through Time

Science.gov (United States)

Walker, R. J.

2001-12-01

Extending Os isotopic measurements to ancient plume sources may help to constrain how and when the well-documented isotopic heterogeneities in modern systems were created. Komatiites and picrites associated with plume-related volcanism are valuable tracers of the Os isotopic composition of plumes because of their typically high Os concentrations and relatively low Re/Os. Re-Os data are now available for a variety of Phanerozoic, Proterozoic and Archean komatiites and picrites. As with modern plumes, the sources of Archean and Proterozoic komatiites exhibit a large range of initial 187Os/188Os ratios. Most komatiites are dominated by sources with chondritic Os isotopic compositions (e.g. Song La; Norseman-Wiluna; Pyke Hill; Alexo), though some (e.g. Gorgona) derive from heterogeneous sources. Of note, however, two ca. 2.7 Ga systems, Kostomuksha (Russia) and Belingwe (Zimbabwe), have initial ratios enriched by 2-3% relative to the contemporary convecting upper mantle. These results suggest that if the 187Os enrichment was due to the incorporation of minor amounts of recycled crust into the mantle source of the rocks, the crust formed very early in Earth history. Thus, the Os results could reflect derivation of melt from hybrid mantle whose composition was modified by the addition of mafic crustal material that would most likely have formed between 4.2 and 4.5 Ga. Alternately, the mantle sources of these komatiites may have derived a portion of their Os from the putative 187Os - and 186Os -enriched outer core. For this hypothesis to be applicable to Archean rocks, an inner core of sufficient mass would have to have crystallized sufficiently early in Earth history to generate an outer core with 187Os enriched by at least 3% relative to the chondritic average. Using the Pt-Re-Os partition coefficients espoused by our earlier work, and assuming linear growth of the inner core started at 4.5 Ga and continued to present, would yield an outer core at 2.7 Ga with a gamma Os

The December 2008 Crammont rock avalanche, Mont Blanc massif area, Italy

Directory of Open Access Journals (Sweden)

P. Deline

2011-12-01

Full Text Available We describe a 0.5 Mm³ rock avalanche that occurred in 2008 in the western Alps and discuss possible roles of controlling factors in the context of current climate change. The source is located between 2410 m and 2653 m a.s.l. on Mont Crammont and is controlled by a densely fractured rock structure. The main part of the collapsed rock mass deposited at the foot of the rock wall. A smaller part travelled much farther, reaching horizontal and vertical travel distances of 3050 m and 1560 m, respectively. The mobility of the rock mass was enhanced by channelization and snow. The rock-avalanche volume was calculated by comparison of pre- and post-event DTMs, and geomechanical characterization of the detachment zone was extracted from LiDAR point cloud processing. Back analysis of the rock-avalanche runout suggests a two stage event.

There was no previous rock avalanche activity from the Mont Crammont ridge during the Holocene. The 2008 rock avalanche may have resulted from permafrost degradation in the steep rock wall, as suggested by seepage water in the scar after the collapse in spite of negative air temperatures, and modelling of rock temperatures that indicate warm permafrost (T > −2 °C.

Results of using engineering and technological measures for rock burst prevention. [USSR

Energy Technology Data Exchange (ETDEWEB)

Kulikov, A P; Nechaev, A V; Khmara, O I

1980-01-01

The paper evaluates methods for rock burst forecasting and rock burst prevention used in the Donbass, Kuzbass, Karaganda and Pechora basins. Forecasting methods are based on measuring the initial velocity of gas flow from test boreholes and/or quantity ratio of drillings leaving a test borehole and monitoring seismoacoustic signals. Number of working faces at which each of the methods for rock burst forecasting is used is given. Methods for rock burst prevention are comparatively evaluated: explosive fracturing of rocks in seam roof or seam floor, fluid injection (water and surfactants), drilling destressing boreholes, cutting destressing slots using cutting machines or water jets, mining protective coal seams first for reducing rock burst hazard in protected coal seams, using narrow web coal cutter loaders, remote control of coal cutters at working faces with extremely high rock burst hazard, using mining schemes which reduce rock burst hazards (e.g. long pillar mining system). From 1976 to 1979 number of rock bursts in underground coal mines in the USSR decreased by 5 times in comparison to the period 1961 to 1965. (3 refs.) (In Russian)

Sensitivity and uncertainty analyses applied to one-dimensional radionuclide transport in a layered fractured rock: MULTFRAC --Analytic solutions and local sensitivities

International Nuclear Information System (INIS)

Gureghian, A.B.; Wu, Y.T.; Sagar, B.

1992-12-01

Exact analytical solutions based on the Laplace transforms are derived for describing the one-dimensional space-time-dependent, advective transport of a decaying species in a layered, saturated rock system intersected by a planar fracture of varying aperture. These solutions, which account for advection in fracture, molecular diffusion into the rock matrix, adsorption in both fracture and matrix, and radioactive decay, predict the concentrations in both fracture and rock matrix and the cumulative mass in the fracture. The solute migration domain in both fracture and rock is assumed to be semi-infinite with non-zero initial conditions. The concentration of each nuclide at the source is allowed to decay either continuously or according to some periodical fluctuations where both are subjected to either a step or band release mode. Two numerical examples related to the transport of Np-237 and Cm-245 in a five-layered system of fractured rock were used to verify these solutions with several well established evaluation methods of Laplace inversion integrals in the real and complex domain. In addition, with respect to the model parameters, a comparison of the analytically derived local sensitivities for the concentration and cumulative mass of Np-237 in the fracture with the ones obtained through a finite-difference method of approximation is also reported

Biomarkers, carbon isotopic composition and source rock potentials of Awgu coals, middle Benue trough, Nigeria

Science.gov (United States)

Adedosu, Taofik A.; Sonibare, Oluwadayo O.; Tuo, Jincai; Ekundayo, Olusegun

2012-05-01

Coal and carbonaceous shale samples were collected from two boreholes (BH 94 and BH 120) in Awgu formation of Middle Benue Trough, Nigeria. Source rock potentials of the samples were studied using biomarkers and carbon isotopic composition. Biomarkers in the aliphatic fractions in the samples were studied using Gas Chromatography-Mass Spectrometry (GC-MS). The Carbon isotope analysis of individual n-alkanes in the aliphatic fraction was performed using Gas Chromatography-Combustion-Isotope Ratio Mass Spectrometer (GC-IRMS). The abundance of hopanes, homohopanes (C31-C35), and C29 steranes in the samples indicate terrestrial plant, phytoplankton and cyanobacteria contributions to the organic matter that formed the coal. High (Pr/Ph) ratio (3.04-11.07) and isotopic distribution of individual alkanes showed that the samples consisted of mixed terrestrial/marine organic matter deposited under oxic condition in lacustrine-fluvial/deltaic depositional environment. The maturity parameters derived from biomarker distributions showed that the samples are in the main phase of oil window.

Stages of material transformations of Archean-Proterozoic rocks (Central-Karelian domain)

International Nuclear Information System (INIS)

Vinogradov, V.I.; Buyakajte, M.I.; Kolodyazhnyj, S.Yu.; Leonov, M.G.; Orlov, S.Yu.

2001-01-01

The age of the Archean-Proterozoic rocks from the south-east part of the Central-Karelian domain was determined by the method of Rb-Sr dating. It was ascertained that the age of the least tectonized rocks of granite-greenstone Archean foundation makes up 2800±70 mln. years at initial strontium isotopic ratio of 0.7022±0.0007. Gneisses of mainly plagiogranite composition, their age 1930±118 mln. years and strontium isotopic ratio 0.7170±0.0026, constitute the second group of the rocks. It is shown that isotopic age defined for the two groups of rocks agrees well with major geological events on the Baltic shield and planet as a whole [ru

Chemical variations in Yellowknife Bay formation sedimentary rocks analyzed by ChemCam on board the Curiosity rover on Mars

Science.gov (United States)

Mangold, Nicolas; Forni, Olivier; Dromart, G.; Stack, K.M.; Wiens, Roger C.; Gasnault, Olivier; Sumner, Dawn Y.; Nachon, Marion; Meslin, Pierre-Yves; Anderson, Ryan B.; Barraclough, Bruce; Bell, J.F.; Berger, G.; Blaney, D.L.; Bridges, J.C.; Calef, F.; Clark, Brian R.; Clegg, Samuel M.; Cousin, Agnes; Edgar, L.; Edgett, Kenneth S.; Ehlmann, B.L.; Fabre, Cecile; Fisk, M.; Grotzinger, John P.; Gupta, S.C.; Herkenhoff, Kenneth E.; Hurowitz, J.A.; Johnson, J. R.; Kah, Linda C.; Lanza, Nina L.; Lasue, Jeremie; Le Mouélic, S.; Lewin, Eric; Malin, Michael; McLennan, Scott M.; Maurice, S.; Melikechi, Noureddine; Mezzacappa, Alissa; Milliken, Ralph E.; Newsome, H.L.; Ollila, A.; Rowland, Scott K.; Sautter, Violaine; Schmidt, M.E.; Schroder, S.; D'Uston, C.; Vaniman, Dave; Williams, R.A.

2015-01-01

The Yellowknife Bay formation represents a ~5 m thick stratigraphic section of lithified fluvial and lacustrine sediments analyzed by the Curiosity rover in Gale crater, Mars. Previous works have mainly focused on the mudstones that were drilled by the rover at two locations. The present study focuses on the sedimentary rocks stratigraphically above the mudstones by studying their chemical variations in parallel with rock textures. Results show that differences in composition correlate with textures and both manifest subtle but significant variations through the stratigraphic column. Though the chemistry of the sediments does not vary much in the lower part of the stratigraphy, the variations in alkali elements indicate variations in the source material and/or physical sorting, as shown by the identification of alkali feldspars. The sandstones contain similar relative proportions of hydrogen to the mudstones below, suggesting the presence of hydrous minerals that may have contributed to their cementation. Slight variations in magnesium correlate with changes in textures suggesting that diagenesis through cementation and dissolution modified the initial rock composition and texture simultaneously. The upper part of the stratigraphy (~1 m thick) displays rocks with different compositions suggesting a strong change in the depositional system. The presence of float rocks with similar compositions found along the rover traverse suggests that some of these outcrops extend further away in the nearby hummocky plains.

Environmental consequences of shale gas exploitation and the crucial role of rock microfracturing

Science.gov (United States)

Renard, Francois

2015-04-01

The growing exploitation of unconventional gas and oil resources has dramatically changed the international market of hydrocarbons in the past ten years. However, several environmental concerns have also been identified such as the increased microseismicity, the leakage of gas into freshwater aquifers, and the enhanced water-rock interactions inducing the release of heavy metals and other toxic elements in the produced water. In all these processes, fluids are transported into a network of fracture, ranging from nanoscale microcracks at the interface between minerals and the kerogen of the source rock, to well-developed fractures at the meter scale. Characterizing the fracture network and the mechanisms of its formation remains a crucial goal. A major difficulty when analyzing fractures from core samples drilled at depth is that some of them are produced by the coring process, while some other are produced naturally at depth by the coupling between geochemical and mechanical forces. Here, I present new results of high resolution synchrotron 3D X-ray microtomography imaging of shale samples, at different resolutions, to characterize their microfractures and their mechanisms of formation. The heterogeneities of rock microstructure are also imaged, as they create local stress concentrations where cracks may nucleate or along which they propagate. The main results are that microcracks form preferentially along kerogen-mineral interfaces and propagate along initial heterogeneities according to the local stress direction, connecting to increase the total volume of fractured rock. Their lifetime is also an important parameter because they may seal by fluid circulation, fluid-rock interactions, and precipitation of a cement. Understanding the multi-scale processes of fracture network development in shales and the coupling with fluid circulation represents a key challenge for future research directions.

Cenozoic alkaline volcanic rocks with carbonatite affinity in the Bohemian Massif: Their sources and magma generation

Czech Academy of Sciences Publication Activity Database

Ulrych, Jaromír; Štěpánková-Svobodová, Jana

2014-01-01

Roč. 46, 1/2 (2014), s. 45-58 ISSN 0369-2086 R&D Projects: GA AV ČR(CZ) IAA300130902 Institutional support: RVO:67985831 Keywords : alkaline volcanic rocks * melilitic rocks * carbonatites * magma generation * metasomatism * Cenozoic * Bohemian Massif Subject RIV: DB - Geology ; Mineralogy

Numerical Simulation of Blast Vibration and Crack Forming Effect of Rock-Anchored Beam Excavation in Deep Underground Caverns

Directory of Open Access Journals (Sweden)

XinPing Li

2017-01-01

Full Text Available Aiming at surrounding rock damage induced by dynamic disturbance from blasting excavation of rock-anchored beam in rock mass at moderate or far distance in underground cavern, numerical model of different linear charging density and crustal stress in underground cavern is established by adopting dynamic finite element software based on borehole layout, charging, and rock parameter of the actual situation of a certain hydropower station. Through comparison in vibration velocity, contour surface of rock mass excavation, and the crushing extent of excavated rock mass between calculation result and field monitoring, optimum linear charging density of blast hole is determined. Studies are also conducted on rock mass vibration in moderate or far distance to blasting source, the damage of surrounding rock in near-field to blasting source, and crushing degree of excavated rock mass under various in situ stress conditions. Results indicate that, within certain range of in situ stress, the blasting vibration is independent of in situ stress, while when in situ stress is increasing above certain value, the blasting vibration velocity will be increasing and the damage of surrounding rock and the crushing degree of excavated rock mass will be decreasing.

Crack propagation of brittle rock under high geostress

Science.gov (United States)

Liu, Ning; Chu, Weijiang; Chen, Pingzhi

2018-03-01

Based on fracture mechanics and numerical methods, the characteristics and failure criterions of wall rock cracks including initiation, propagation, and coalescence are analyzed systematically under different conditions. In order to consider the interaction among cracks, adopt the sliding model of multi-cracks to simulate the splitting failure of rock in axial compress. The reinforcement of bolts and shotcrete supporting to rock mass can control the cracks propagation well. Adopt both theory analysis and simulation method to study the mechanism of controlling the propagation. The best fixed angle of bolts is calculated. Then use ansys to simulate the crack arrest function of bolt to crack. Analyze the influence of different factors on stress intensity factor. The method offer more scientific and rational criterion to evaluate the splitting failure of underground engineering under high geostress.

Memory-Efficient Onboard Rock Segmentation

Science.gov (United States)

Burl, Michael C.; Thompson, David R.; Bornstein, Benjamin J.; deGranville, Charles K.

2013-01-01

Rockster-MER is an autonomous perception capability that was uploaded to the Mars Exploration Rover Opportunity in December 2009. This software provides the vision front end for a larger software system known as AEGIS (Autonomous Exploration for Gathering Increased Science), which was recently named 2011 NASA Software of the Year. As the first step in AEGIS, Rockster-MER analyzes an image captured by the rover, and detects and automatically identifies the boundary contours of rocks and regions of outcrop present in the scene. This initial segmentation step reduces the data volume from millions of pixels into hundreds (or fewer) of rock contours. Subsequent stages of AEGIS then prioritize the best rocks according to scientist- defined preferences and take high-resolution, follow-up observations. Rockster-MER has performed robustly from the outset on the Mars surface under challenging conditions. Rockster-MER is a specially adapted, embedded version of the original Rockster algorithm ("Rock Segmentation Through Edge Regrouping," (NPO- 44417) Software Tech Briefs, September 2008, p. 25). Although the new version performs the same basic task as the original code, the software has been (1) significantly upgraded to overcome the severe onboard re source limitations (CPU, memory, power, time) and (2) "bulletproofed" through code reviews and extensive testing and profiling to avoid the occurrence of faults. Because of the limited computational power of the RAD6000 flight processor on Opportunity (roughly two orders of magnitude slower than a modern workstation), the algorithm was heavily tuned to improve its speed. Several functional elements of the original algorithm were removed as a result of an extensive cost/benefit analysis conducted on a large set of archived rover images. The algorithm was also required to operate below a stringent 4MB high-water memory ceiling; hence, numerous tricks and strategies were introduced to reduce the memory footprint. Local filtering

Rock fragmentation

Energy Technology Data Exchange (ETDEWEB)

Brown, W.S.; Green, S.J.; Hakala, W.W.; Hustrulid, W.A.; Maurer, W.C. (eds.)

1976-01-01

Experts in rock mechanics, mining, excavation, drilling, tunneling and use of underground space met to discuss the relative merits of a wide variety of rock fragmentation schemes. Information is presented on novel rock fracturing techniques; tunneling using electron beams, thermocorer, electric spark drills, water jets, and diamond drills; and rock fracturing research needs for mining and underground construction. (LCL)

Pore connectivity effects on solute transport in rocks

International Nuclear Information System (INIS)

Hu, Qinhong; Ewing, Robert P.

2001-01-01

Retardation of nuclear contaminants in rock matrices can lead to long retention times, allowing substantial radionuclide decay prior to eventual release. Imbibition and diffusion into the rock matrix can move contaminants away from an active fracture, thereby contributing to their retardation. However, diffusive transport in some rocks may behave anomalously because of their sparsely connected porespace, in contrast to diffusion in rocks with denser pore connections. We examined imbibition of weakly sorbing tracers into welded tuff and Indiana sandstone, and water imbibition into metagraywacke and Berea sandstone. Tuff samples were initially equilibrated to 12% and 76% water (v/v) within controlled humidity chambers, while the other rocks were air-dried. For imbibition, one face was exposed to water, with or without tracer, and uptake was measured over time. Following imbibition, tracer concentration measurements were made at fine (1 mm) increments. Three anomalous results were observed: (1) Indiana sandstone and metagraywacke showed mass of imbibed water scaling as time 0.26 , while tuff and Berea sandstone showed the more classical scaling with time 0.5 ; (2) tracer movement into dry (2% initial saturation) Indiana sandstone showed a dispersion pattern similar to that expected during tracer movement into moist (76% initial saturation) tuff; and (3) tracer concentrations at the inlet face of the tuff sample were approximately twice those deeper inside the sample. The experiment was then modeled using random walk methods on a 3-D lattice with different values of pore coordination. Network model simulations that used a pore coordination of 1.49 for Indiana sandstone and 1.56 for metagraywacke showed similar temporal scaling, a result of their porespace being close to the percolation threshold. Tracer concentration profiles in Indiana sandstone and tuff were closely matched by simulations that used pore coordinations of 1.49 and 1.68, respectively, because of how low

Pore Connectivity Effects on Solute Transport in Rocks

International Nuclear Information System (INIS)

Oinhong Hu

2001-01-01

Retardation of nuclear contaminants in rock matrices can lead to long retention times, allowing substantial radionuclide decay prior to eventual release. Imbibition and diffusion into the rock matrix can move contaminants away from an active fracture, thereby contributing to their retardation. However, diffusive transport in some rocks may behave anomalously because of their sparsely connected porespace, in contrast to diffusion in rocks with denser pore connections. We examined imbibition of weakly sorbing tracers into welded tuff and Indiana sandstone, and water imbibition into metagraywacke and Berea sandstone. Tuff samples were initially equilibrated to 12% and 76% water (v/v) within controlled humidity chambers, while the other rocks were air-dried. For imbibition, one face was exposed to water, with or without tracer, and uptake was measured over time. Following imbibition, tracer concentration measurements were made at fine (1 mm) increments. Three anomalous results were observed: (1) Indiana sandstone and metagraywacke showed mass of imbibed water scaling as time 0.26 , while tuff and Berea sandstone showed the more classical scaling with time 0.05 ; (2) tracer movement into dry (2% initial saturation) Indiana sandstone showed a dispersion pattern similar to that expected during tracer movement into moist (76% initial saturation) tuft and (3) tracer concentrations at the inlet face of the tuff sample were approximately twice those deeper inside the sample. The experiment was then modeled using random walk methods on a 3-D lattice with different values of pore coordination. Network model simulations that used a pore coordination of 1.49 for Indiana sandstone and 1.56 for metagraywacke showed similar temporal scaling, a result of their porespace being close to the percolation threshold. Tracer concentration profiles in Indiana sandstone and tuff were closely matched by simulations that used pore coordinations of 1.49 and 1.68, respectively, because of how low

Geophysical monitoring as an information source of rock massif behaviour

Directory of Open Access Journals (Sweden)

Pavel Bláha

2008-06-01

Full Text Available Geophysical measurements are an integral part of engineering-geological investigation where theypresent a wide range of useful information about the tested geological medium and about its geotechnicalqualities. Lately, repeated geophysical measurements in different time intervals have been used to judgethe changes occurring in the rock massif. These measurements bear the characteristics of total monitoring.This total monitoring contains series of repeated measurements and further an integrated spectrum of linkedactivities including evaluation, comparison with the warning state and making a decision about takingprecautions. From the range of geophysical methods and methodologies used for monitoring in full sensewe may mention, for example, continuous seismoacoustic measurements in mining constructions; (whichmay result even in recalling of the personnel, and further, also seismic measurements in the surroundingsof atomic power stations and measurements considering the protection against radioactive elements and their decay components.As a full monitoring we may also classify measurements in dumping sites with the aid of repeated geoelectrical measurements in the system of fixed electrodes under impermeable foils.These measurements are mostly carried out from time to time followed by taking immediate action when the foil is found damaged. In practice the term monitoring is used, although not very correctly, for all periodically repeated measurements, which do not result in taking action or interference, but supply a wide range of information about the rock massif behavior in time.

Acoustic Emission Behavior of Rock-Like Material Containing Two Flaws in the Process of Deformation Failure

Directory of Open Access Journals (Sweden)

Quan-Sheng Liu

2015-01-01

Full Text Available Many sudden disasters (such as rock burst by mining extraction originate in crack initiation and propagation. Meanwhile a large number of shock waves are produced by rock deformation and failure. With the purpose of investigating crack coalescence and failure mechanism in rock, experimental research of rock-like materials with two preexisting flaws was performed. Moreover, the AE technique and photographic monitoring were adopted to clarify further the procedure of the crack coalescence and failure. It reveals that AE location technique can record the moments of crack occurrences and follow the crack growth until final failure. Finally, the influence of different flaw geometries on crack initiation strength is analyzed in detail. This research provides increased understanding of the fracture mechanism of mining-induced disasters.

The origin, source and cycling of methane in deep crystalline rock biosphere

Directory of Open Access Journals (Sweden)

Riikka eKietäväinen

2015-07-01

Full Text Available The emerging interest in using stable bedrock formations for industrial purposes, e.g. nuclear waste disposal, has increased the need for understanding microbiological and geochemical processes in deep crystalline rock environments, including the carbon cycle. Considering the origin and evolution of life on Earth, these environments may also serve as windows to the past. Various geological, chemical and biological processes can influence the deep carbon cycle. Conditions of CH4 formation, available substrates and time scales can be drastically different from surface environments. This paper reviews the origin, source and cycling of methane in deep terrestrial crystalline bedrock with an emphasis on microbiology. In addition to potential formation pathways of CH4, microbial consumption of CH4 is also discussed. Recent studies on the origin of CH4 in continental bedrock environments have shown that the traditional separation of biotic and abiotic CH4 by the isotopic composition can be misleading in substrate-limited environments, such as the deep crystalline bedrock. Despite of similarities between Precambrian continental sites in Fennoscandia, South Africa and North America, where deep methane cycling has been studied, common physicochemical properties which could explain the variation in the amount of CH4 and presence or absence of CH4 cycling microbes were not found. However, based on their preferred carbon metabolism, methanogenic microbes appeared to have similar spatial distribution among the different sites.

The origin, source, and cycling of methane in deep crystalline rock biosphere.

Science.gov (United States)

Kietäväinen, Riikka; Purkamo, Lotta

2015-01-01

The emerging interest in using stable bedrock formations for industrial purposes, e.g., nuclear waste disposal, has increased the need for understanding microbiological and geochemical processes in deep crystalline rock environments, including the carbon cycle. Considering the origin and evolution of life on Earth, these environments may also serve as windows to the past. Various geological, chemical, and biological processes can influence the deep carbon cycle. Conditions of CH4 formation, available substrates and time scales can be drastically different from surface environments. This paper reviews the origin, source, and cycling of methane in deep terrestrial crystalline bedrock with an emphasis on microbiology. In addition to potential formation pathways of CH4, microbial consumption of CH4 is also discussed. Recent studies on the origin of CH4 in continental bedrock environments have shown that the traditional separation of biotic and abiotic CH4 by the isotopic composition can be misleading in substrate-limited environments, such as the deep crystalline bedrock. Despite of similarities between Precambrian continental sites in Fennoscandia, South Africa and North America, where deep methane cycling has been studied, common physicochemical properties which could explain the variation in the amount of CH4 and presence or absence of CH4 cycling microbes were not found. However, based on their preferred carbon metabolism, methanogenic microbes appeared to have similar spatial distribution among the different sites.

Sorptivity of rocks and soils of the van Genuchten-Mualem type

Energy Technology Data Exchange (ETDEWEB)

Zimmerman, R.W.; Bodvarsson, G.S. [Lawrence Berkeley Lab., CA (United States)

1991-06-01

One hydrological process that will have great relevance to the performance of the proposed underground radioactive waste repository at Yucca Mountain, Nevada, is that of the absorption of water from a water-filled fracture into the adjacent unsaturated rock formation. The rate at which water is imbibed by a rock depends on the hydrological properties of the rock and on the initial saturation (or initial capillary suction) of the formation. The hydrological properties that affect imbibition are the relative permeability function and the capillary pressure function. These functions are often collectively referred to as the `characteristic functions` of the porous medium. For one-dimensional absorption, it can be shown that, regardless of the details of the characteristic functions, the total amount of water imbibed by the formation, per unit surface area, will be proportional to the square root of the elapsed time. Hence the ability of a rock or soil to imbibe water can be quantified by a parameter known as the sorptivity S, which is defined such that the cumulative volumetric liquid influx per unit area is given by Q = S{radical}t. The paper discusses the simplification of these characteristic functions of porous medium.

Oil(Gas) - source rock correlation technique

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-01

The overview of bio-marker parameters which are applicable to hydrocarbon exploration has been illustrated. Experimental analysis of saturated hydrocarbon and bio-markers of the Pohang E and F core samples has been carried out. Samples were extracted by stirring in dichloromethane at 40-50 degree for 10 hours. The saturated, aromatic and resin fractions of the extract were obtained using thin layer chromatograms. The relative abundance of normal alkane fraction of the samples is low except lowest interval, which is probably due to the biodegradation. The bio-marker assemblage of hopanoids and steranes has been characterized. According to the analysis of saturated hydrocarbons and bio-markers, the sedimentary environment of the Pohang core samples is marine and transitional zone except the terrestrial environment of the lowest samples such as 610.5 m from E core and 667.2 m from F core. The thermal maturity through the studied interval did not reach oil window even though slight increase in thermal maturity with depth, which coincide with Rock Eval pyrolysis data. In order to check the validation of analysis of the bio-markers, same samples were analyzed by the University of Louis Pasteur, France. The distribution and relative peak area of the bio-markers were identical with those by laboratory of KIGAM. For the 2 nd stage of the research, analysis of bio-markers other than hopanoids and steranes should be continued. (author). 29 figs., 7 tabs.

Phosphorus availability in an acid tropical soil amended with phosphate rocks

International Nuclear Information System (INIS)

Zaharah, A.R.; Sharifuddin, H.A.H.

2002-01-01

The fate of P from phosphate rocks applied to Malaysian soils has not been studied in detail. Since the plantation sector is the major consumer of phosphate rock (PR) in Malaysia, studies on the dissolution and agronomic effectiveness of PR are of great interest to the country. Thus a series of greenhouse and laboratory experiments involving conventional chemical extractants and 32 P isotopic techniques was carried out to evaluate the agronomic effectiveness of PR sources of different reactivity. Phosphorus and other chemical properties of the soil and PRs studied were determined. The P solubility tests by 2% formic acid, 2% citric acid and neutral ammonium citrate gave positive correlation with P uptake by one-year old oil palm seedlings. Neutral ammonium citrate proved to be a better indicator of PR solubility and its correlation coefficient with P uptake improved by expressing citrate solubility as a percentage of the rock rather than as a percentage of total P 2 0 5 content. The agronomic effectiveness of TSP and 6 PR sources was evaluated in glasshouse conditions with oil palm seedlings for one year-period. The percentage of PR dissolution varied greatly among PR sources. The PR dissolution was assessed by 0.5 M NaOH, Pi strip, L-value and 1 M ammonium citrate-dissolved Ca. Irrespective of the methods used, the more reactive PR such as North Carolina and Tunisia dissolved more P than the lower reactive sources such as Christmas Island and China PR. All the four methods used gave positive correlation with plant P uptake, with 0.5M NaOH being the best indirect method for determining PR dissolution. Less than 30% of the applied P was dissolved during the one-year period, with only about 15 to 40% of the dissolved P being taken up by the oil palm seedlings. A laboratory 32 P isotopic exchange method was also carried out in this acid soil to assess the soil P status parameters. A low water soluble P concentration (Cp) was found for all PRs used. The ratio of the

Fracture network growth for prediction of fracture characteristics and connectivity in tight reservoir rocks

NARCIS (Netherlands)

Barnhoorn, A.; Cox, S.F.

2012-01-01

Fracturing experiments on very low-porosity dolomite rocks shows a difference in growth of fracture networks by stress-driven fracturing and fluid-driven fracturing. Stress-driven fracture growth, in the absence of fluid pressure, initially forms fractures randomly throughout the rocks followed by

Rock mechanics for hard rock nuclear waste repositories

International Nuclear Information System (INIS)

Heuze, F.E.

1981-09-01

The mined geologic burial of high level nuclear waste is now the favored option for disposal. The US National Waste Terminal Storage Program designed to achieve this disposal includes an extensive rock mechanics component related to the design of the wastes repositories. The plan currently considers five candidate rock types. This paper deals with the three hard rocks among them: basalt, granite, and tuff. Their behavior is governed by geological discontinuities. Salt and shale, which exhibit behavior closer to that of a continuum, are not considered here. This paper discusses both the generic rock mechanics R and D, which are required for repository design, as well as examples of projects related to hard rock waste storage. The examples include programs in basalt (Hanford/Washington), in granitic rocks (Climax/Nevada Test Site, Idaho Springs/Colorado, Pinawa/Canada, Oracle/Arizona, and Stripa/Sweden), and in tuff

Elastic Rock Heterogeneity Controls Brittle Rock Failure during Hydraulic Fracturing

Science.gov (United States)

Langenbruch, C.; Shapiro, S. A.

2014-12-01

For interpretation and inversion of microseismic data it is important to understand, which properties of the reservoir rock control the occurrence probability of brittle rock failure and associated seismicity during hydraulic stimulation. This is especially important, when inverting for key properties like permeability and fracture conductivity. Although it became accepted that seismic events are triggered by fluid flow and the resulting perturbation of the stress field in the reservoir rock, the magnitude of stress perturbations, capable of triggering failure in rocks, can be highly variable. The controlling physical mechanism of this variability is still under discussion. We compare the occurrence of microseismic events at the Cotton Valley gas field to elastic rock heterogeneity, obtained from measurements along the treatment wells. The heterogeneity is characterized by scale invariant fluctuations of elastic properties. We observe that the elastic heterogeneity of the rock formation controls the occurrence of brittle failure. In particular, we find that the density of events is increasing with the Brittleness Index (BI) of the rock, which is defined as a combination of Young's modulus and Poisson's ratio. We evaluate the physical meaning of the BI. By applying geomechanical investigations we characterize the influence of fluctuating elastic properties in rocks on the probability of brittle rock failure. Our analysis is based on the computation of stress fluctuations caused by elastic heterogeneity of rocks. We find that elastic rock heterogeneity causes stress fluctuations of significant magnitude. Moreover, the stress changes necessary to open and reactivate fractures in rocks are strongly related to fluctuations of elastic moduli. Our analysis gives a physical explanation to the observed relation between elastic heterogeneity of the rock formation and the occurrence of brittle failure during hydraulic reservoir stimulations. A crucial factor for understanding

Rock.XML - Towards a library of rock physics models

Science.gov (United States)

Jensen, Erling Hugo; Hauge, Ragnar; Ulvmoen, Marit; Johansen, Tor Arne; Drottning, Åsmund

2016-08-01

Rock physics modelling provides tools for correlating physical properties of rocks and their constituents to the geophysical observations we measure on a larger scale. Many different theoretical and empirical models exist, to cover the range of different types of rocks. However, upon reviewing these, we see that they are all built around a few main concepts. Based on this observation, we propose a format for digitally storing the specifications for rock physics models which we have named Rock.XML. It does not only contain data about the various constituents, but also the theories and how they are used to combine these building blocks to make a representative model for a particular rock. The format is based on the Extensible Markup Language XML, making it flexible enough to handle complex models as well as scalable towards extending it with new theories and models. This technology has great advantages as far as documenting and exchanging models in an unambiguous way between people and between software. Rock.XML can become a platform for creating a library of rock physics models; making them more accessible to everyone.

O rock desligado de Lóki

Directory of Open Access Journals (Sweden)

Márcia Carvalho

2012-08-01

Full Text Available This paper presents an analysis of the documentary Loki: ArnaldoBaptista (2009, direct by Paulo Henrique Fontenelle. This analysis investigates thehistorical research and biographical approach, examining in particular the enhancement oforal memory and musical performances from different sources to put into perspective thehistory of Brazilian rock on movie screens and television.

Modelling of nuclear explosions in hard rock sites

International Nuclear Information System (INIS)

Brunish, W.M.; App, F.N.

1993-01-01

This study represents part of a larger effort to systematically model the effects of differing source region properties on ground motion from underground nuclear explosions at the Nevada Test Site. In previous work by the authors the primary emphasis was on alluvium and both saturated and unsaturated tuff. We have attempted to model events on Pahute Mesa, where either the working point medium, or some of the layers above the working point, or both, are hard rock. The complex layering at these sites, however, has prevented us from drawing unambiguous conclusions about modelling hard rock

Use of phosphate rocks for sustainable agriculture

International Nuclear Information System (INIS)

Zapata, F.; Roy, R.N.

2004-01-01

This publication deals with the direct application of phosphate rock (PR) sources to agriculture. Phosphorus (P) is an essential plant nutrient and its deficiency restricts crop yields severely. Tropical and subtropical soils are predominantly acidic, and often extremely P deficient with high P-sorption (fixation) capacities. Therefore, substantial P inputs are required for optimum plant growth and adequate food and fibre production. Manufactured water-soluble P fertilizers such as superphosphates are commonly recommended to correct P deficiencies, but most developing countries import these fertilizers, which are often in limited supply and represent a major outlay for resource-poor farmers. In addition, intensification of agricultural production in these countries necessitates the addition of P not only to increase crop production but also to improve soil P status in order to avoid further soil degradation. Hence, it is imperative to explore alternative P sources. Under certain soil and climate conditions, the direct application of PR, especially where available locally, has proved to be an agronomically and economically sound alternative to the more expensive superphosphates. PR deposits occur worldwide, but few are mined (for use mainly as raw materials to manufacture water-soluble P fertilizers). The Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture initiated a Coordinated Research Project called 'The use of nuclear and related techniques for evaluating the agronomic effectiveness of phosphatic fertilizers, in particular rock phosphates'. This was implemented by institutes of developing and industrialized countries from 1993 to 1998. The results obtained yielded new information on: chemistry of soil P; tests for available soil P; phosphate nutrition of crops; agronomic effectiveness of PR products; and P fertilizer recommendations with particular emphasis on PR use. Within the framework of the integrated plant nutrition systems promoted by

Stress, strain, and temperature induced permeability changes in potential repository rocks

International Nuclear Information System (INIS)

Heard, H.C.; Duba, A.

1977-01-01

Work is in progress to assess the permeability characteristics of coarse-grained igneous rocks as affected by pressure, deviatoric stress, and temperature. In order to predict the long-term behavior of these rocks, both virgin and fractured, permeability and all principal strains resulting from an imposed deviatoric stress under various simulated lithostatic pressures are being measured. In addition, compressional as well as shear velocities and electrical conductivity are being evaluated along these principal directions. These simultaneous measurements are being made initially at 25 0 C on a 15 cm diameter by 30 cm long sample in a pressure apparatus controlled by a mini-computer. Correlation of these data with similar field observations should then allow simplified exploration for a suitable repository site as well as the prediction of the response of a mined cavity with both distance and time at this site. After emplacement of the waste canisters, the mechanical stability and hydrologic integrity of this mined repository will be directly influenced by the fracturing of the surrounding rock which results from local temperature differences and the thermal expansion of that rock. Temperatures (and, hence, these differences) in the vicinity of the repository are expected to be affected by the presence of pore fluids (single- or two-phase) in the rock, the heat capacity and the thermal conductivity of this system. In turn, these are all dependent upon lithostatic pressure, pore pressure, and stress. Thermal expansion (and fracturing) will also be affected by the lithostatic (and effective) pressure, the deviatoric stress field, and the initial anisotropy of the rock

3D random Voronoi grain-based models for simulation of brittle rock damage and fabric-guided micro-fracturing

Directory of Open Access Journals (Sweden)

E. Ghazvinian

2014-12-01

Full Text Available A grain-based distinct element model featuring three-dimensional (3D Voronoi tessellations (random poly-crystals is proposed for simulation of crack damage development in brittle rocks. The grain boundaries in poly-crystal structure produced by Voronoi tessellations can represent flaws in intact rock and allow for numerical replication of crack damage progression through initiation and propagation of micro-fractures along grain boundaries. The Voronoi modelling scheme has been used widely in the past for brittle fracture simulation of rock materials. However the difficulty of generating 3D Voronoi models has limited its application to two-dimensional (2D codes. The proposed approach is implemented in Neper, an open-source engine for generation of 3D Voronoi grains, to generate block geometry files that can be read directly into 3DEC. A series of Unconfined Compressive Strength (UCS tests are simulated in 3DEC to verify the proposed methodology for 3D simulation of brittle fractures and to investigate the relationship between each micro-parameter and the model's macro-response. The possibility of numerical replication of the classical U-shape strength curve for anisotropic rocks is also investigated in numerical UCS tests by using complex-shaped (elongated grains that are cemented to one another along their adjoining sides. A micro-parameter calibration procedure is established for 3D Voronoi models for accurate replication of the mechanical behaviour of isotropic and anisotropic (containing a fabric rocks.

Pre-earthquake signals – Part I: Deviatoric stresses turn rocks into a source of electric currents

Directory of Open Access Journals (Sweden)

F. T. Freund

2007-09-01

Full Text Available Earthquakes are feared because they often strike so suddenly. Yet, there are innumerable reports of pre-earthquake signals. Widespread disagreement exists in the geoscience community how these signals can be generated in the Earth's crust and whether they are early warning signs, related to the build-up of tectonic stresses before major seismic events. Progress in understanding and eventually using these signals has been slow because the underlying physical process or processes are basically not understood. This has changed with the discovery that, when igneous or high-grade metamorphic rocks are subjected to deviatoric stress, dormant electronic charge carriers are activated: electrons and defect electrons. The activation increases the number density of mobile charge carriers in the rocks and, hence, their electric conductivity. The defect electrons are associated with the oxygen anion sublattice and are known as positive holes or pholes for short. The boundary between stressed and unstressed rock acts a potential barrier that lets pholes pass but blocks electrons. Therefore, like electrons and ions in an electrochemical battery, the stress-activated electrons and pholes in the "rock battery" have to flow out in different directions. When the circuit is closed, the battery currents can flow. The discovery of such stress-activated currents in crustal rocks has far-reaching implications for understanding pre-earthquake signals.

Sedimentary environments and hydrocarbon potential of cretaceous rocks of indus basin, Pakistan

International Nuclear Information System (INIS)

Sheikh, S.A.; Naseem, S.

1999-01-01

Cretaceous rocks of Indus Basin of Pakistan are dominated by clastics with subordinate limestone towards the top. These rocks represent shelf facies and were deposited in deltaic to reducing marine conditions at variable depths. Indications of a silled basin with restricted circulation are also present. Cretaceous fine clastics/carbonates have good source and reservoir qualities. Variable geothermal gradients in different parts of basin have placed these rocks at different maturity levels; i.e. from oil to condensate and to gas. The potential of these rocks has been proved by several oil and gas discoveries particularly in the Central and Southern provinces of Indus Basin. (author)

Rock burst governance of working face under igneous rock

Science.gov (United States)

Chang, Zhenxing; Yu, Yue

2017-01-01

As a typical failure phenomenon, rock burst occurs in many mines. It can not only cause the working face to cease production, but also cause serious damage to production equipment, and even result in casualties. To explore how to govern rock burst of working face under igneous rock, the 10416 working face in some mine is taken as engineering background. The supports damaged extensively and rock burst took place when the working face advanced. This paper establishes the mechanical model and conducts theoretical analysis and calculation to predict the fracture and migration mechanism and energy release of the thick hard igneous rock above the working face, and to obtain the advancing distance of the working face when the igneous rock fractures and critical value of the energy when rock burst occurs. Based on the specific conditions of the mine, this paper put forward three kinds of governance measures, which are borehole pressure relief, coal seam water injection and blasting pressure relief.

Determination of radioactivity in Chinese phosphate rock and fertilizer

International Nuclear Information System (INIS)

Chen Jingjian; Zhu Yongyi; Yang Juncheng

1993-01-01

The presented paper reported the radioactivity of U-238, Ra-226, Th-232 and K-40 in Chinese phosphate rocks by gamma spectrographic analysis during 1985-1990. The results showed that the decay chain of U-238-Ra-226 was the main source of radionuclides in phosphate rocks. The radionuclides in phosphate fertilizer differed from the forms of phosphate fertilizer. U-238 was the most important radionuclide in phosphoric compound fertilizer. The transfer rate of radionuclides was also estimated. (2 figs., 1 tab.)

Water-rock-tailings interactions and sources of sulfur and metals in the subtropical mining region of Taxco, Guerrero (southern Mexico): A multi-isotopic approach

International Nuclear Information System (INIS)

Talavera Mendoza, Oscar; Ruiz, Joaquin; Díaz Villaseñor, Elvia; Ramírez Guzmán, Alejandro; Cortés, Alejandra; Salgado Souto, Sergio Adrián; Dótor Almazán, Azucena; Rivera Bustos, Reymundo

2016-01-01

Multi-isotope (H, O, S, Sr, Pb) systems coupled with conventional (major and trace element) hydrogeochemical analysis were applied to determine the origin of water, to model water-rock-tailings interactions and for source apportionment of sulfur and associated toxic metals in the mining region of Taxco, Guerrero in southern Mexico. Oxygen and H isotopes indicate that meteoric water in the zone is rainwater undergoing varying degrees of isotopic fractionation by atmospheric evaporation whereas Sr isotopes trace the interaction of pristine water from volcanics of the regional recharge zone and subsequently flowing through sandstone and shale to spring points. Leachates form from two distinctive sources (spring water and surface water) having differential interactions with bedrocks prior to entering the tailings. Compared to pristine water, leachates are enriched in sulfate, metals (e.g. Fe, Mn, Pb and Zn) and metalloids (e.g. As). The sulfur isotopic composition of ore-sulfides, leachates, secondary precipitates, regional surface water and hypogenic sulfates is described in terms of a two-component mixing model with shale of Mexcala and limestone of Morelos formations representing the light and heavy end-members, respectively, whereas Sr isotopic composition is bracketed combining three lithogenic (Mexcala/Morelos, Tilzapotla and Taxco Schist) sources. Finally, leachates have a mixture of lead from ore-sulfides and Taxco Schist Formation (Family I) or from ore-sulfides alone (Family II). The application of multiple environmental isotopic techniques is an outstanding tool for elucidating complex interactions of water with bedrocks and tailings and for determining the source of sulfur and toxic metal from mining and other metal polluted environments. - Highlights: • We applied multi-isotope techniques to model water-bedrocks-tailings interaction. • Spring water records fractionation by evaporation and interaction with local rocks. • The sulfur cycle is modeled in

The Australian national reactive phosphate rock project - Aims, experimental approach, and site characteristics

International Nuclear Information System (INIS)

McLaughlin, M.J.

2002-01-01

Field-based cutting trials were established across Australia in a range of environments to evaluate the agronomic effectiveness of 5 phosphate rocks, and 1 partially acidulated phosphate rock, relative to either single super-phosphate or triple superphosphate. The phosphate rocks differed in reactivity, as determined by the degree of carbonate substitution for phosphate in the apatite structure and solubility of phosphorus present in the fertilizers in 2% formic acid, 2% citric acid and neutral ammonium citrate. Sechura (Bayovar) and North Carolina phosphate rocks were highly reactive (>70% solubility in 2% formic acid), whilst Khouribja (Moroccan) and Hamrawein (Egypt) phosphate rock were moderately reactive. Duchess phosphate rock from Queensland was relatively unreactive ( 2 , from 4.0 to 5.1, and Colwell extractable phosphorus ranged from 3 to 47 μg/g prior to fertilizer application. Two core experiments were established at each site. The first measured the effects of phosphate rock reactivity on agronomic effectiveness, while the second core experiment measured the effects of the degree of water solubility of the phosphorus source on agronomic effectiveness. The National Reactive Phosphate Rock Project trials provided the opportunity to confirm the suitability of accepted procedures to model fertilizer response and to develop new approaches for comparing different fertilizer responses. The Project also provided the framework for subsidiary studies such as the effect of fertilizer source on soil phosphorus extractability; cadmium and fluorine concentrations in herbage; evaluation of soil phosphorus tests; and the influence of particle size on phosphate rock effectiveness. The National Reactive Phosphate Rock Project presents a valuable model for a large, Australia-wide, collaborative team approach to an important agricultural issue. The use of standard and consistent experimental methodologies at every site ensured that maximum benefit was obtained from data

Microscopic study of rock for estimating long-term behavior. Research document

International Nuclear Information System (INIS)

Ichikawa, Yasuaki

2003-02-01

Micro-structure of rock plays an essential role for their long-term behavior. For elucidating long-term characteristics of granite we here present the followings: 1) Conformal Lase Scanning Microscope (LSM) observation of configuration of a joint in granite, its Fourier analysis and the change under uniaxial stress condition, 2) characterization of the mechanism of microcrack initiation and propagation observed by stereoscopic microscope under uniaxial/triaxial compression and relaxation tests, 3) observation of microcrack initiation and propagation by LSM under uniaxial compression, and 4) a study of strong discontinuity analysis included in the homogenization theory to predict the long-term behavior of micro/macro-level stress for granite. Rock image processing and analysis become a fundamental procedure to determine rock surface discontinuities. In Chapter 2 LSM that can acquire three-dimensional images is introduced to observe the roughness of discontinuity in a rock specimen. Then, discontinuities appeared on circular sections are identified by LSM and characterized by a Discrete Fourier Transform (DFT) analysis. The change of discontinuities is observed under applying stress. Microcrack generation and propagation play an essential role to predict the long-term behavior of rock. In Chapter 3 a progressive development of cracking in granite is revealed by using stereoscopic microscope under water-saturated triaxial compression condition. Next by using LSM observe the procedure of micro-cracking under uniaxial compression condition. Obviously the micro-crack initiation and propagation controls the time-dependent behavior of granite. We have analysed the behavior by a viscoelastic theory applied in homogenization method. However since it is difficult to determine the inter-granular properties of constituent crystals and to represent the stress-dependent nonlinear characteristics by this method, we study a strong discontinuity analysis included in the

A computer-assisted rock type data catalogue for gas formations; Ein rechnergestuetzter Gesteinsdatenkatalog fuer Gasformationen

Energy Technology Data Exchange (ETDEWEB)

Reitenbach, V.; Pusch, G.; Moeller, M.; Koll, S. [TU Clausthal (Germany). Inst. fuer Erdoel- und Erdgastechnik; Constantini, A.; Junker, A.; Anton, H. [RWE Dea AG, Hamburg (Germany)

2007-09-13

Modern reservoir management commonly requires versatile reservoir data which are neces-sary for integrated reservoir characterization, evaluation and development planning. The rock data necessary for numerical reservoir simulation studies often have to be collected from different sources, analysed and sorted with a considerable effort. In a framework of DGMK research program (DGMK project 593-9/4), the Institute of Petro-leum Engineering (Clausthal University of Technology) and RWE DEA AG have developed a new tool named Rock Data Catalogue, which is capable of managing large amounts of rock data more efficiently and deriving new specific correlations for European rock types. The use of Rock Data Catalogue can facilitate the essential input data generation and proc-essing procedure for reservoir simulation studies. The Rock Data Catalogue is comprised of a Data Base Module of digitalized reservoir rock data and an interactive Data Correlation Module. Both modules are built-up as an interface to common reservoir simulation software. The universal structure of the software also makes it possible to exchange the data with other rock data information systems. The Data Correlation Module implements a ''Decision-Structure'' module, which helps the reservoir engineer to select the rock data for analysis and correlation depending on its litho-facial type and permeability class. The Data Base Module enables a quick search of appro-priated data sets and their export into the correlation module. The open source data of the North German Rotliegend gas formations as well as the data of measurements on Rotliegend core samples performed at the ITE in course of the DGMK tight gas projects were implemented in the rock data base. Correlations of poro/perm data, two-phase flow and capillary pressure functions of the Rotliegend sandstones with the per-meability range between 20 and 0.01 mD are implemented in the rock data base and serve for quality checking of the

Evaluation of Five Sedimentary Rocks Other Than Salt for Geologic Repository Siting Purposes

Energy Technology Data Exchange (ETDEWEB)

Croff, A.G.; Lomenick, T.F.; Lowrie, R.S.; Stow, S.H.

2003-11-15

The US Department of Energy (DOE), in order to increase the diversity of rock types under consideration by the geologic disposal program, initiated the Sedimary ROck Program (SERP), whose immediate objectiv eis to evaluate five types of secimdnary rock - sandstone, chalk, carbonate rocks (limestone and dolostone), anhydrock, and shale - to determine the potential for siting a geologic repository. The evaluation of these five rock types, together with the ongoing salt studies, effectively results in the consideration of all types of relatively impermeable sedimentary rock for repository purposes. The results of this evaluation are expressed in terms of a ranking of the five rock types with respect to their potential to serve as a geologic repository host rock. This comparative evaluation was conducted on a non-site-specific basis, by use of generic information together with rock evaluation criteria (RECs) derived from the DOE siting guidelines for geologic repositories (CFR 1984). An information base relevant to rock evaluation using these RECs was developed in hydrology, geochemistry, rock characteristics (rock occurrences, thermal response, rock mechanics), natural resources, and rock dissolution. Evaluation against postclosure and preclosure RECs yielded a ranking of the five subject rocks with respect to their potential as repository host rocks. Shale was determined to be the most preferred of the five rock types, with sandstone a distant second, the carbonate rocks and anhydrock a more distant third, and chalk a relatively close fourth.

Evaluation of Five Sedimentary Rocks Other Than Salt for Geologic Repository Siting Purposes

International Nuclear Information System (INIS)

Croff, A.G.; Lomenick, T.F.; Lowrie, R.S.; Stow, S.H.

2003-01-01

The US Department of Energy (DOE), in order to increase the diversity of rock types under consideration by the geologic disposal program, initiated the Sedimary ROck Program (SERP), whose immediate objectiv eis to evaluate five types of secimdnary rock - sandstone, chalk, carbonate rocks (limestone and dolostone), anhydrock, and shale - to determine the potential for siting a geologic repository. The evaluation of these five rock types, together with the ongoing salt studies, effectively results in the consideration of all types of relatively impermeable sedimentary rock for repository purposes. The results of this evaluation are expressed in terms of a ranking of the five rock types with respect to their potential to serve as a geologic repository host rock. This comparative evaluation was conducted on a non-site-specific basis, by use of generic information together with rock evaluation criteria (RECs) derived from the DOE siting guidelines for geologic repositories (CFR 1984). An information base relevant to rock evaluation using these RECs was developed in hydrology, geochemistry, rock characteristics (rock occurrences, thermal response, rock mechanics), natural resources, and rock dissolution. Evaluation against postclosure and preclosure RECs yielded a ranking of the five subject rocks with respect to their potential as repository host rocks. Shale was determined to be the most preferred of the five rock types, with sandstone a distant second, the carbonate rocks and anhydrock a more distant third, and chalk a relatively close fourth.

On the age of the Onverwacht Group, Swaziland sequence, South Africa. [radioactive dating of stratified igneous rocks

Science.gov (United States)

Jahn, B.-M.; Shih, C.-Y.

1974-01-01

Some rocks of the Onverwacht Group, South Africa, have been analyzed for Rb and Sr concentrations and Sr isotopic composition. These rocks include volcanic rocks, layered ultramafic differentiates and cherty sediments. Whole rock data indicate that the Rb-Sr isotopic systems in many samples were open and yield no reasonable isochron relationships. However, the data of mineral separates from a basaltic komatiite define a good isochron of 3.50 (plus or minus .2) b.y. with an initial Sr-87/Sr-86 ratio of 0.70048 plus or minus 5. The orthodox interpretation of this age is the time of the low grade metamorphism. It is reasonable to assume that the age of 3.50 b.y. might also represent the time of initial Onverwacht volcanism and deposition. The initial Sr-87/Sr-86 ratio obtained above is important to an understanding of the Sr isotopic composition of the Archean upper mantle.

One-fifth-scale and full-scale fuel element rocking tests

International Nuclear Information System (INIS)

Nau, P.V.; Olsen, B.E.

1978-06-01

Using 1 / 5 -scale and 1 / 1 -scale (prototype H451) fuel elements, one, two, or three stacked elements on a clamped base element were rocked from an initial release position. Relative displacement, rock-down loads, and dowel pin shear forces were measured. A scaled comparison between 1 / 5 -scale and 1 / 1 -scale results was made to evaluate the model scaling laws, and an error analysis was performed to assess the accuracy and usefulness of the test data

Ore potential of basic rocks in Finland

International Nuclear Information System (INIS)

Reino, J.; Ekberg, M.; Heinonen, P.; Karppanen, T.; Hakapaeae, A.; Sandberg, E.

1993-02-01

The report is associated with a study programme on basic rocks, which has the aim to complement the preliminary site investigations on repository for TVO's (Teollisuuden Voima Oy) spent nuclear fuel. The report comprises a mining enterprise's view of the ore potential of basic plutonic rocks in Finland. The ores associated with basic plutonic rocks are globally known and constitute a significant share of the global mining industry. The ores comprise chromium, vanadium-titanium-iron, nickel-copper and platinum group element ores. The resources of the metals in question and their mining industry are examined globally. A review of the use of these metals in the industry is presented as well. General factors affecting the mining industry, such as metal prices, political conjunctures, transport facilities, environmental requirements and raw material sources for the Finnish smelters have been observed from the point of view of their future effect on exploration activity and industrial development in Finland. Information on ores and mineralizations associated with Finnish basic rocks have been compiled in the report. The file comprises 4 chromium occurrences, 8 vanadium-titanium-iron occurrences, 13 PGE occurrences and 38 nickel-copper occurrences

A study about the long-term stability of sedimentary rock

International Nuclear Information System (INIS)

Yoshino, Naoto; Miyanomae, Shun-ichi; Inoue, Hiroyuki; Nashimoto, Yutaka

2005-02-01

In this paper, following two issues were examined and estimated, (1) the influence of near field condition factor to the dynamical behavior of sedimentary soft rock, (2) the long term estimation of the dynamical behavior considering the condition of Horonobe area. As the study about the influence of near field condition factor to the dynamical behavior of sedimentary soft rock, the thermal factor was focused on and the laboratory tests using test pieces which were sampled in Horonobe area were carried out under the water temperature were 20 degrees and 80 degrees. As a result, the time dependence parameter in variable-compliance-type constitutive-equation could be obtained. And comparison between creep property under 20 degrees and 80 degrees was conducted. In addition, the general properties of sedimentary soft rock under several conditions were identified by the survey of the literature. And the way how to confirm the dynamical properties of sedimentary soft rock with in-situ test were presented. For the study on the short-term and long-term stability of rock surrounding buffer materials, numerical simulations were carried out assuming several conditions. The direction of disposal tunnels and the ratio of rock strength by initial stress were estimated to be the main factor affecting the short-term stability of rock. Time dependency of rock and the stiffness of buffer material were estimated to be the main factor affecting the long-term stability of rock. (author)

Evaluating Re-Os systematics in organic-rich sedimentary rocks in response to petroleum generation using hydrous pyrolysis experiments

Science.gov (United States)

Rooney, A.D.; Selby, D.; Lewan, M.D.; Lillis, P.G.; Houzay, J.-P.

2012-01-01

Successful application of the 187Re–187Os geochronometer has enabled the determination of accurate and precise depositional ages for organic-rich sedimentary rocks (ORS) as well as establishing timing constraints of petroleum generation. However, we do not fully understand the systematics and transfer behaviour of Re and Os between ORS and petroleum products (e.g., bitumen and oil). To more fully understand the behaviour of Re–Os systematics in both source rocks and petroleum products we apply hydrous pyrolysis to two immature hydrocarbon source rocks: the Permian Phosphoria Formation (TOC = 17.4%; Type II-S kerogen) and the Jurassic Staffin Formation (TOC = 2.5%; Type III kerogen). The laboratory-based hydrous pyrolysis experiments were carried out for 72 h at 250, 300, 325 and 350 °C. These experiments provided us with whole rock, extracted rock and bitumen and in some cases expelled oil and asphaltene for evaluation of Re–Os isotopic and elemental abundance. The data from these experiments demonstrate that the majority (>95%) of Re and Os are housed within extracted rock and that thermal maturation does not result in significant transfer of Re or Os from the extracted rock into organic phases. Based on existing thermodynamic data our findings suggest that organic chelating sites have a greater affinity for the quadravalent states of Re and Os than sulphides. Across the temperature range of the hydrous pyrolysis experiments both whole rock and extracted rock 187Re/188Os ratios show small variations (3.3% and 4.7%, for Staffin, respectively and 6.3% and 4.9% for Phosphoria, respectively). Similarly, the 187Os/188Os ratios show only minor variations for the Staffin and Phosphoria whole rock and extracted rock samples (0.6% and 1.4% and 1.3% and 2.2%). These isotopic data strongly suggest that crude oil generation through hydrous pyrolysis experiments does not disturb the Re–Os systematics in ORS as supported by various studies on natural systems. The

Magnetic susceptibility and relation to initial 87Sr/86Sr for granitoids of the central Sierra Nevada, California

Science.gov (United States)

Bateman, P.C.; Dodge, F.C.W.; Kistler, R.W.

1991-01-01

Measurement of the magnetic susceptibility of more than 6000 samples of granitic rock from the Mariposa 1?? by 2?? quadrangle, which crosses the central part of the Sierra Nevada batholith between 37?? and 38??N latitude, shows that magnetic susceptibility values are above 10-2 SI units in the east and central parts of the batholith and drop abruptly to less than 10-3 SI units in the western foothills. In a narrow transitional zone, intermediate values (10-3 to 10-2) prevail. Magnetic susceptibility appears to decrease slightly westward within the zones of both high and low values. Magnetic susceptibility in plutonic rocks is chiefly a function of the abundance of magnetite, which depends, in turn, on the total iron content of the rocks and their oxidation ratio. Correlations of magnetic susceptibility with initial 87Sr/86Sr suggest that oxidation ratios have been inherited from the source regions for the magmas from which the rocks crystallized. Reduction of Fe3+ to Fe2+ by organic carbon or other reducing substances may also have affected magnetic susceptibility. -from Authors

Stepwise Rock-Eval pyrolysis as a tool for typing heterogeneous organic matter in soils

Energy Technology Data Exchange (ETDEWEB)

Hetenyi, M.; Nyilas, T.; Toth, T.M. [Department of Mineralogy, Geochemistry and Petrology, University of Szeged, P.O. Box 651, H-6701 Szeged (Hungary)

2005-08-15

This paper presents an application of Rock-Eval pyrolysis for estimating the proportion of the components with different thermal stability in soil organic matter, the maturity of which corresponds to the early stage of diagenesis. For testing the validity of the modified Rock-Eval method, parallel series of pyrolysis were carried out on sedimentary rock samples. The temperature program was selected on the basis of the results obtained from stepwise Rock-Eval pyrolysis and from the mathematical deconvolution of pyrograms. The proportion of the original biomolecules in soil organic matter was calculated by the integration of pyrograms below 350{sup o}C and could be determined rapidly by one single pyrolysis using 350{sup o}C as initial cracking temperature. At 380{sup o}C, both the mathematical and the experimental methods provide reliable information about the proportion of the humic substances. Conversely, for rock samples, mathematical deconvolution of the pyrograms showed the heterogeneity of the sedimentary organic matter, the maturity of which corresponds to late diagenesis, without any estimation of the proportion of the different components. The rate of organic carbon accumulation in the studied soils and the decomposition rate of biopolymers were interpreted as a function of land-use and redox conditions. Differences in the precursor vegetation and in the environmental parameters resulted in markedly reduced carbon storage and higher degree of humification in the agricultural soil than in the adjacent forest soil. Redox conditions strongly affected both the amount and the elemental composition of the stored organic matter. The decomposition rate of biopolymers appeared to be controlled mainly by the contribution of resistant lignin components to the source biomass and, to a lesser extent, by redox conditions.

For Those About to Rock : Naislaulajat rock-genressä

OpenAIRE

Herranen, Linda

2015-01-01

For those about to rock – naislaulajat rock-genressä antaa lukijalleen kokonaisvaltaisen käsityksen naisista rock-genressä: rockin historiasta, sukupuolittuneisuudesta, seksismistä, suomalaisten naislaulajien menestyksestä. Työn aineisto on koottu aihepiirin kirjallisuudesta ja alalla toimiville naislaulajille teetettyjen kyselyiden tuloksista. Lisäksi avaan omia kokemuksiani ja ajatuksiani, jotta näkökulma naisista rock-genressä tulisi esille mahdollisimman monipuolisesti. Ajatus aihees...

Experimental Investigation of the Influence of Confining Stress on Hard Rock Fragmentation Using a Conical Pick

Science.gov (United States)

Li, Xibing; Wang, Shaofeng; Wang, Shanyong

2018-01-01

High geostress is a prominent condition in deep excavations and affects the cuttability of deep hard rock. This study aims to determine the influence of confining stress on hard rock fragmentation as applied by a conical pick. Using a true triaxial test apparatus, static and coupled static and dynamic loadings from pick forces were applied to end faces of cubic rock specimens to break them under biaxial, uniaxial and stress-free confining stress conditions. The cuttability indices (peak pick force, insertion depth and disturbance duration), failure patterns and fragment sizes were measured and compared to estimate the effects of confining stress. The results show that the rock cuttabilities decreased in order from rock breakages under stress-free conditions to uniaxial confining stress and then to biaxial confining stress. Under biaxial confining stress, only flake-shaped fragments were stripped from the rock surfaces under the requirements of large pick forces or disturbance durations. As the level of uniaxial confining stress increased, the peak pick force and the insertion depth initially increased and then decreased, and the failure patterns varied from splitting to partial splitting and then to rock bursts with decreasing average fragment sizes. Rock bursts will occur under elastic compression via ultra-high uniaxial confining stresses. There are two critical uniaxial confining stress levels, namely stress values at which peak pick forces begin to decrease and improve rock cuttability, and those at which rock bursts initially occur and cutting safety decreases. In particular, hard rock is easiest to split safely and efficiently under stress-free conditions. Moreover, coupled static preloading and dynamic disturbance can increase the efficiency of rock fragmentation with increasing preloading levels and disturbance amplitudes. The concluding remarks confirm hard rock cuttability using conical pick, which can improve the applicability of mechanical excavation in

Proceedings of the 3. Canada-US rock mechanics symposium and 20. Canadian rock mechanics symposium : rock engineering 2009 : rock engineering in difficult conditions

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-07-01

This conference provided a forum for geologists, mining operators and engineers to discuss the application of rock mechanics in engineering designs. Members of the scientific and engineering communities discussed challenges and interdisciplinary elements involved in rock engineering. New geological models and methods of characterizing rock masses and ground conditions in underground engineering projects were discussed along with excavation and mining methods. Papers presented at the conference discussed the role of rock mechanics in forensic engineering. Geophysics, geomechanics, and risk-based approaches to rock engineering designs were reviewed. Issues related to high pressure and high flow water conditions were discussed, and new rock physics models designed to enhance hydrocarbon recovery were presented. The conference featured 84 presentations, of which 9 have been catalogued separately for inclusion in this database. tabs., figs.

Emplacement of rock avalanche material across saturated sediments, Southern Alp, New Zealand

Science.gov (United States)

Dufresne, A.; Davies, T. R.; McSaveney, M. J.

2012-04-01

The spreading of material from slope failure events is not only influenced by the volume and nature of the source material and the local topography, but also by the materials encountered in the runout path. In this study, evidence of complex interactions between rock avalanche and sedimentary runout path material were investigated at the 45 x 106 m3 long-runout (L: 4.8 km) Round Top rock avalanche deposit, New Zealand. It was sourced within myolinitic schists of the active strike-slip Alpine Fault. The narrow and in-failure-direction elongate source scarp is deep-seated, indicating slope failure was triggered by strong seismic activity. The most striking morphological deposit features are longitudinal ridges aligned radially to source. Trenching and geophysical surveys show bulldozed and sheared substrate material at ridge termini and laterally displaced sedimentary strata. The substrate failed at a minimum depth of 3 m indicating a ploughing motion of the ridges into the saturated material below. Internal avalanche compression features suggest deceleration behind the bulldozed substrate obstacle. Contorted fabric in material ahead of the ridge document substrate disruption by the overriding avalanche material deposited as the next down-motion hummock. Comparison with rock avalanches of similar volume but different emplacement environments places Round Top between longer runout avalanches emplaced over e.g. playa lake sediments and those with shorter travel distances, whose runout was apparently retarded by topographic obstacles or that entrained high-friction debris. These empirical observations indicate the importance of runout path materials on tentative trends in rock avalanche emplacement dynamics and runout behaviour.

Fundamental observations concerning hysteresis in the deformation of intact and jointed rock with applications to nonlinear attenuation in the near source region

International Nuclear Information System (INIS)

Boitnott, G.N.

1993-01-01

In order to estimate yields of large underground explosions, it is important that we have a clear understanding of the near source phenomena and their effects on regional and teleseismic signals. While it is generally accepted that a considerable amount of attenuation and resultant waveform distortion occurs due to nonlinear deformation near the source, an area that has received little attention is the broad enveloping region where moderate stress perturbations occur. In this region, where strain perturbation amplitudes range from microstrains to a few millistrains, the resulting deformation of rock is inelastic and nonlinear but little to no permanent deformation results. Owing to its great extent, the moderate strain regime has the potential to influence the entire frequency band of the regional and teleseismic signals and thus may be central to the problem of inferring source characteristics from far field signals. Detailed rheological descriptions are required in order to understand the effects of the nonlinearities on the spectral content of regional and teleseismic signals

Art Rocks with Rock Art!

Science.gov (United States)

Bickett, Marianne

2011-01-01

This article discusses rock art which was the very first "art." Rock art, such as the images created on the stone surfaces of the caves of Lascaux and Altimira, is the true origin of the canvas, paintbrush, and painting media. For there, within caverns deep in the earth, the first artists mixed animal fat, urine, and saliva with powdered minerals…

Performance of pineapple slips inoculated with diazotrophic phosphate-solubilizing bacteria and rock phosphate

Directory of Open Access Journals (Sweden)

Lílian Estrela Borges Baldotto

2014-06-01

Full Text Available Besides fixing N2, some diazotrophic bacteria or diazotrophs, also synthesize organic acids and are able to solubilize rock phosphates, increasing the availability of P for plants. The application of these bacteria to pineapple leaf axils in combination with rock phosphate could increase N and P availability for the crop, due to the bacterial activity of biological nitrogen fixation and phosphate solubilization. The objectives of this study were: (i to select and characterize diazotrophs able to solubilize phosphates in vitro and (ii evaluate the initial performance of the pineapple cultivars Imperial and Pérola in response to inoculation with selected bacteria in combination with rock phosphate. The experiments were conducted at Universidade Estadual do Norte Fluminense Darcy Ribeiro, in 2009. In the treatments with bacteria the leaf contents of N, P and K were higher than those of the controls, followed by an increase in plant growth. These results indicate that the combined application of diazotrophic phosphate-solubilizing bacteria Burkholderia together with Araxá rock phosphate can be used to improve the initial performance of pineapple slips.

Initial waste package interaction tests: status report

International Nuclear Information System (INIS)

Shade, J.W.; Bradley, D.J.

1980-12-01

This report describes the results of some initial investigations of the effects of rock media on the release of simulated fission products from a sngle waste form, PNL reference glass 76-68. All tests assemblies contained a minicanister prepared by pouring molten, U-doped 76-68 glass into a 2-cm-dia stanless steel tube closed at one end. The tubes were cut to 2.5 to 7.5 cm in length to expose a flat glass surface rimmed by the canister wall. A cylindrical, whole rock pellet, cut from one of the rock materials used, was placed on the glass surface then both the canister and rock pellet were packed in the same type of rock media ground to about 75 μm to complete the package. Rock materials used were a quartz monzonite basalt and bedded salt. These packages were run from 4 to 6 weeks in either 125 ml digestion bombs or 850 ml autoclaves capable of direct solution sampling, at either 250 or 150 0 C. Digestion bomb pressures were the vapor pressure of water, 600 psig at 250 0 C, and the autoclaves were pressurized at 2000 psig with an argon overpressure. In general, the solution chemistry of these initial package tests suggests that the rock media is the dominant controlling factor and that rock-water interaction may be similar to that observed in some geothermal areas. In no case was uranium observed in solution above 15 ppB. The observed leach rates of U glass not in contact with potential sinks (rock surfaces and alteration products) have been observed to be considerably higher. Thus the use of leach rates and U concentrations observed from binary leach experiments (waste-form water only) to ascertain long-term environmental consequences appear to be quite conservative compared to actual U release in the waste package experiments. Further evaluation, however, of fission product transport behavior and the role of alteration phases as fission product sinks is required

Microwave propagation and absorption and its thermo-mechanical consequences in heterogeneous rocks.

Science.gov (United States)

Meisels, R; Toifl, M; Hartlieb, P; Kuchar, F; Antretter, T

2015-02-10

A numerical analysis in a two-component model rock is presented including the propagation and absorption of a microwave beam as well as the microwave-induced temperature and stress distributions in a consistent way. The analyses are two-dimensional and consider absorbing inclusions (discs) in a non-absorbing matrix representing the model of a heterogeneous rock. The microwave analysis (finite difference time domain - FDTD) is performed with values of the dielectric permittivity typical for hard rocks. Reflections at the discs/matrix interfaces and absorption in the discs lead to diffuse scattering with up to 20% changes of the intensity in the main beam compared to a homogeneous model rock. The subsequent thermo-mechanical finite element (FE) analysis indicates that the stresses become large enough to initiate damage. The results are supported by preliminary experiments on hard rock performed at 2.45 GHz.

Mechanical weathering and rock erosion by climate-dependent subcritical cracking

Science.gov (United States)

Eppes, Martha-Cary; Keanini, Russell

2017-06-01

This work constructs a fracture mechanics framework for conceptualizing mechanical rock breakdown and consequent regolith production and erosion on the surface of Earth and other terrestrial bodies. Here our analysis of fracture mechanics literature explicitly establishes for the first time that all mechanical weathering in most rock types likely progresses by climate-dependent subcritical cracking under virtually all Earth surface and near-surface environmental conditions. We substantiate and quantify this finding through development of physically based subcritical cracking and rock erosion models founded in well-vetted fracture mechanics and mechanical weathering, theory, and observation. The models show that subcritical cracking can culminate in significant rock fracture and erosion under commonly experienced environmental stress magnitudes that are significantly lower than rock critical strength. Our calculations also indicate that climate strongly influences subcritical cracking—and thus rock weathering rates—irrespective of the source of the stress (e.g., freezing, thermal cycling, and unloading). The climate dependence of subcritical cracking rates is due to the chemophysical processes acting to break bonds at crack tips experiencing these low stresses. We find that for any stress or combination of stresses lower than a rock's critical strength, linear increases in humidity lead to exponential acceleration of subcritical cracking and associated rock erosion. Our modeling also shows that these rates are sensitive to numerous other environment, rock, and mineral properties that are currently not well characterized. We propose that confining pressure from overlying soil or rock may serve to suppress subcritical cracking in near-surface environments. These results are applicable to all weathering processes.

Geochemical typification of kimberlite and related rocks of the North Anabar region, Yakutia

Science.gov (United States)

Kargin, A. V.; Golubeva, Yu. Yu.

2017-11-01

The results of geochemical typification of kimberlites and related rocks (alneites and carbonatites) of the North Anabar region are presented with consideration of the geochemical specification of their source and estimation of their potential for diamonds. The content of representative trace elements indicates the predominant contribution of an asthenospheric component (kimberlites and carbonatites) in their source, with a subordinate contribution of vein metasomatic formations containing Cr-diopside and ilmenite. A significant contribution of water-bearing potassium metasomatic parageneses is not recognized. According to the complex of geochemical data, the studied rocks are not industrially diamondiferous.

Initial operating experience and recent development on the TRIUMF optically pumped polarized H- ion source

International Nuclear Information System (INIS)

Schmor, P.W.; Law, W.M.; Levy, C.D.P.; McDonald, M.

1988-01-01

A polarized H - ion source using optical pumping techniques has been developed at TRIUMF. This source was used to demonstrate (on an ion source test stand) the feasibility of producing 10- μA of ∼ 60% polarized H - ion beam in a dc mode suitable for injection into the TRIUMF cyclotron. The source has been installed in a 300 kV high voltage terminal connected to the cyclotron via a recently constructed beam transport line. A polarization of 80% is anticipated near the end of 1988 after the installation of a superconducting solenoid to the source. In this paper the authors describe the initial operating experience, recent developments, and the future plans for the TRIUMF optically pumped polarized ion source

EFFECT OF ALTERNATIVE MULTINUTRIENT SOURCES ON SOIL CHEMICAL PROPERTIES

Directory of Open Access Journals (Sweden)

Vanessa Martins

2015-02-01

Full Text Available The current high price of potassium chloride and the dependence of Brazil on imported materials to supply the domestic demand call for studies evaluating the efficiency of alternative sources of nutrients. The aim of this work was to evaluate the effect of silicate rock powder and a manganese mining by-product, and secondary materials originated from these two materials, on soil chemical properties and on brachiaria production. This greenhouse experiment was conducted in pots with 5 kg of soil (Latossolo Vermelho-Amarelo distrófico - Oxisol. The alternative nutrient sources were: verdete, verdete treated with NH4OH, phonolite, ultramafic rock, mining waste and the proportion of 75 % of these K fertilizers and 25 % lime. Mixtures containing 25 % of lime were heated at 800 ºC for 1 h. These sources were applied at rates of 0, 150, 300, 450 and 600 kg ha-1 K2O, and incubated for 45 days. The mixtures of heated silicate rocks with lime promoted higher increases in soil pH in decreasing order: ultramafic rock>verdete>phonolite>mining waste. Applying the mining waste-lime mixture increased soil exchangeable K, and available P when ultramafic rock was incorporated. When ultramafic rock was applied, the release of Ca2+ increased significantly. Mining subproduct released the highest amount of Zn2+ and Mn2+ to the soil. The application of alternative sources of K, with variable chemical composition, altered the nutrient availability and soil chemical properties, improving mainly plant development and K plant uptake, and are important nutrient sources.

Recovery of uranium from low-grade sandstone ores and phosphate rock

Energy Technology Data Exchange (ETDEWEB)

Kennedy, R H [United States Atomic Energy Commission, Washington, D. C. (United States)

1967-06-15

This paper is concerned principally with commercial-scale experience in the United States in the recovery of uranium from low-grade sources. Most of these operations have been conducted by the operators of uranium mills as an alternative to processing normal-grade ores. The operations have been generally limited, therefore, to the treatment of low-grade materials generated in the course of mining normal-grade ores. In some circumstances such materials can be treated by simplified procedures as an attractive source of additional production. The experience gained in uranium recovery from phosphate rock will be treated in some detail. The land pebble phosphate rock of central Florida generally contains about 0.01 to 0.02% U{sub 3}O{sub 8}. While no uranium is being recovered from this source at the present time, it does represent a significant potential source of by-product uranium production because of the large tonnages being mined. (author)

Rho-associated kinase (ROCK) function is essential for cell cycle progression, senescence and tumorigenesis.

Science.gov (United States)

Kümper, Sandra; Mardakheh, Faraz K; McCarthy, Afshan; Yeo, Maggie; Stamp, Gordon W; Paul, Angela; Worboys, Jonathan; Sadok, Amine; Jørgensen, Claus; Guichard, Sabrina; Marshall, Christopher J

2016-01-14

Rho-associated kinases 1 and 2 (ROCK1/2) are Rho-GTPase effectors that control key aspects of the actin cytoskeleton, but their role in proliferation and cancer initiation or progression is not known. Here, we provide evidence that ROCK1 and ROCK2 act redundantly to maintain actomyosin contractility and cell proliferation and that their loss leads to cell-cycle arrest and cellular senescence. This phenotype arises from down-regulation of the essential cell-cycle proteins CyclinA, CKS1 and CDK1. Accordingly, while the loss of either Rock1 or Rock2 had no negative impact on tumorigenesis in mouse models of non-small cell lung cancer and melanoma, loss of both blocked tumor formation, as no tumors arise in which both Rock1 and Rock2 have been genetically deleted. Our results reveal an indispensable role for ROCK, yet redundant role for isoforms 1 and 2, in cell cycle progression and tumorigenesis, possibly through the maintenance of cellular contractility.

Change in cap rock porosity triggered by pressure and temperature dependent CO2–water–rock interactions in CO2 storage systems

Directory of Open Access Journals (Sweden)

Christina Hemme

2017-03-01

Full Text Available Carbon capture and storage in deep geological formations is a method to reduce greenhouse gas emissions. Supercritical CO2 is injected into a reservoir and dissolves in the brine. Under the impact of pressure and temperature (P–T the aqueous species of the CO2-acidified brine diffuse through the cap rock where they trigger CO2–water–rock interactions. These geochemical reactions result in mineral dissolution and precipitation along the CO2 migration path and are responsible for a change in porosity and therefore for the sealing capacity of the cap rock. This study focuses on the diffusive mass transport of CO2 along a gradient of decreasing P–T conditions. The process is retraced with a one-dimensional hydrogeochemical reactive mass transport model. The semi-generic hydrogeochemical model is based on chemical equilibrium thermodynamics. Based on a broad variety of scenarios, including different initial mineralogical, chemical and physical parameters, the hydrogeochemical parameters that are most sensitive for safe long-term CO2 storage are identified. The results demonstrate that P–T conditions have the strongest effect on the change in porosity and the effect of both is stronger at high P–T conditions because the solubility of the mineral phases involved depends on P–T conditions. Furthermore, modeling results indicate that the change in porosity depends strongly on the initial mineralogical composition of the reservoir and cap rock as well as on the brine compositions. Nevertheless, a wide range of conditions for safe CO2 storage is identified.

RADIATION CHEMICAL CONVERSION OF OIL DERIVED FROM OIL-BITUMEN ROCK

Directory of Open Access Journals (Sweden)

Lala Jabbarova

2014-06-01

Full Text Available The results of research in the radiation processing of synthetic oil derived from oil–bitumen rock of the Balakhany deposit in Azerbaijan are presented. The study has been conducted on a 60Co gamma-source at a dose rate of P = 0.5 Gy/s and various absorbed doses of D = 43–216 kGy. Samples of synthetic oil from natural bitumen rocks have been analyzed by chromatography, gas chromatography–mass spectrometry, and IR-spectroscopy, and their radiation resistance has been evaluated. The results of the study allow for both assessment of the feasibility of manufacturing petrochemicals for various applications by radiation processing and use of these materials for isolating radioactive sources to preclude their impact on the environment.

Rock Directed Breaking Under the Impulse Load

Science.gov (United States)

Khomeriki, Sergo; Mataradze, Edgar; Chikhradze, Nikoloz; Losaberidze, Marine; Khomeriki, Davit; Shatberashvili, Grigol

2016-10-01

In the work the problem of directed chipping of facing stone material by means of managing of explosion process is considered. The technology of the mining of decorative stone by the use of explosion energy means the very rapid transfer of potential energy of elastic deformations to kinetic energy. As a result, the explosion impulse, in the expanse of the inertia of rock massive, does not cause the increase of existing cracks. In the course of explosion, the shock wave is propagated by ultrasonic velocity and in this case the medium parameters (pressure, density, temperature, velocity) increase in spurts. In spite of this fact the all three conservation laws of mechanics remain valid on basis of three laws the equations are derived by which the parameters of shock wave may be defined by means of the rock physical-mechanical properties. The load on the body volume at breaking under explosion acts over very small period of the time. Therefore, stressed-deformed state of the rock was studied when the impulse load acts on the boundary. It was considered that the mining of the blocks of facing stone is performed from the hard rocks. This means that the breaking proceeds in the zone of elastic deformation. In the conditions of mentioned assumptions, the expression of the stress tensor and displacement of vector components initiated by stressed-deformed state in the rock are written.

The Usability of Rock-Like Materials for Numerical Studies on Rocks

Science.gov (United States)

Zengin, Enes; Abiddin Erguler, Zeynal

2017-04-01

The approaches of synthetic rock material and mass are widely used by many researchers for understanding the failure behavior of different rocks. In order to model the failure behavior of rock material, researchers take advantageous of different techniques and software. But, the majority of all these instruments are based on distinct element method (DEM). For modeling the failure behavior of rocks, and so to create a fundamental synthetic rock material model, it is required to perform related laboratory experiments for providing strength parameters. In modelling studies, model calibration processes are performed by using parameters of intact rocks such as porosity, grain size, modulus of elasticity and Poisson ratio. In some cases, it can be difficult or even impossible to acquire representative rock samples for laboratory experiments from heavily jointed rock masses and vuggy rocks. Considering this limitation, in this study, it was aimed to investigate the applicability of rock-like material (e.g. concrete) to understand and model the failure behavior of rock materials having complex inherent structures. For this purpose, concrete samples having a mixture of %65 cement dust and %35 water were utilized. Accordingly, intact concrete samples representing rocks were prepared in laboratory conditions and their physical properties such as porosity, pore size and density etc. were determined. In addition, to acquire the mechanical parameters of concrete samples, uniaxial compressive strength (UCS) tests were also performed by simultaneously measuring strain during testing. The measured physical and mechanical properties of these extracted concrete samples were used to create synthetic material and then uniaxial compressive tests were modeled and performed by using two dimensional discontinuum program known as Particle Flow Code (PFC2D). After modeling studies in PFC2D, approximately similar failure mechanism and testing results were achieved from both experimental and

Natural analogue for storage of radwaste in crystalline rocks

International Nuclear Information System (INIS)

Brookins, D.G.; Abashian, M.S.; Cohen, L.H.; Wollenberg, H.A. Jr.

1982-01-01

The Bryan-Eldora stock (Colorado) intruded the Precambrian Idaho Springs Formation metamorphic rocks 58 million years ago. Geochronologic-geochemical work by Hart et al. [S.R. Hart et al., in Radiometric Dating for Geologists, E.I. Hamilton, R.S. Farquhar, eds. (Wiley-Interscience, New York, 1968) pp. 73-110] has demonstrated that the heat from the cooling intrusive rocks was sufficient to affect mineral isotopic systematics up to 2000 m from the contact, and the nature of these isotopic perturbations can be explained by a simple diffusion model in turn based on various heat flow models. Our new studies are focused on elemental exchange between stock and intruded rock as a function of distance from the contact; the assumption is made that the stock is a very large, high heat source analogous to a waste form emplaced in the metamorphic rocks without benefit of canister or engineered backfill. Data for U, Th and the REE indicate actinide and lanthanide immobility except perhaps in the 0 to 2m contact zone where some infiltration of the country rocks by stock-derived fluids occurred. Beyond 4m no stock-derived U, Th, REE or *Pb are noted. Further, whole rock Rb-Sr and stable O isotopic data indicate conductive cooling as opposed to convective, water-induced cooling. The intruded rocks possess low porosity and permeability; this helped prevent elemental migration during the 10 5 to 10 6 years of stock crystallization. The petrographic and geochemical studies show that the Idaho Springs (or equivalent) metamorphic rocks are well suited for radwaste storage. 1 figure, 1 table

GEOCHEMICAL INVESTIGATIONS OF CO₂-BRINE-ROCK INTERACTIONS OF THE KNOX GROUP IN THE ILLINOIS BASIN

Energy Technology Data Exchange (ETDEWEB)

Yoksoulian, Lois; Berger, Peter; Freiburg, Jared; Butler, Shane; Leetaru, Hannes

2014-09-30

study suggests only limited potential for the release of United States Environmental Protection Agency regulated inorganic contaminants into potable water sources. Short-term core flood experiments further verify that the carbonate reactions occurring in Knox Group reservoir samples reach equilibrium rapidly. The core flood experiments also lend insight to pressure changes that may occur during CO₂ injection. The Maquoketa Shale experiments reveal that this rock is initially chemically reactive when in contact with CO₂ and brine. However, due to the conservative nature of silicate and clay reaction kinetics and the rapid equilibration of carbonate reactions that occur in the shale, these reactions would not present a significant risk to the competency of the shale as an effective seal rock.

A 3-D wellbore simulator (WELLTHER-SIM) to determine the thermal diffusivity of rock-formations

Science.gov (United States)

Wong-Loya, J. A.; Santoyo, E.; Andaverde, J.

2017-06-01

Acquiring thermophysical properties of rock-formations in geothermal systems is an essential task required for the well drilling and completion. Wellbore thermal simulators require such properties for predicting the thermal behavior of a wellbore and the formation under drilling and shut-in conditions. The estimation of static formation temperatures also needs the use of these properties for the wellbore and formation materials (drilling fluids and pipes, cements, casings, and rocks). A numerical simulator (WELLTHER-SIM) has been developed for modeling the drilling fluid circulation and shut-in processes of geothermal wellbores, and for the in-situ determination of thermal diffusivities of rocks. Bottomhole temperatures logged under shut-in conditions (BHTm), and thermophysical and transport properties of drilling fluids were used as main input data. To model the thermal disturbance and recovery processes in the wellbore and rock-formation, initial drilling fluid and static formation temperatures were used as initial and boundary conditions. WELLTHER-SIM uses these temperatures together with an initial thermal diffusivity for the rock-formation to solve the governing equations of the heat transfer model. WELLTHER-SIM was programmed using the finite volume technique to solve the heat conduction equations under 3-D and transient conditions. Thermal diffusivities of rock-formations were inversely computed by using an iterative and efficient numerical simulation, where simulated thermal recovery data sets (BHTs) were statistically compared with those temperature measurements (BHTm) logged in some geothermal wellbores. The simulator was validated using a well-documented case reported in the literature, where the thermophysical properties of the rock-formation are known with accuracy. The new numerical simulator has been successfully applied to two wellbores drilled in geothermal fields of Japan and Mexico. Details of the physical conceptual model, the numerical

Renewing Rock-Tenn: A Biomass Fuels Assessment for Rock-Tenn's St. Paul Recycled Paper Mill.

Energy Technology Data Exchange (ETDEWEB)

Nelson, Carl

2007-03-31

In the summer of 2006 the Green Institute started the study for the RockTenn paper mill that would evaluate the economics and supply chain reliability of wood waste and other clean biomass as a fuel for the facility. The Green Institute obtained sponsorship from a broad coalition representing the community and the project team included other consultants and university researchers specializing in biomass issues. The final product from the project was a report to: 1) assess the availability of clean biomass fuel for use at the Rock-Tenn site; 2) roughly estimate costs at various annual usage quantities; and 3) develop the building blocks for a supply chain procurement plan. The initial report was completed and public presentations on the results were completed in spring of 2007.

Relationship between the rock mass deformation and places of occurrence of seismological events

Energy Technology Data Exchange (ETDEWEB)

Janusz Makowka; Jozef Kabiesz; Lin-ming Ddou [Central Mining Institute, Katowice (Poland)

2009-09-15

Static effort of rock mass very rarely causes of rock burst in Polish coal mines. Rock bursts with source in the seismic tremor within the roof rock layers are prevailing. A seismic tremor is an effect of rupture or sliding in roof layers above the exploited panel in coal seam, sometime in a distance from actual exploitation. Sliding, as a rule occurs in fault zone and tremors in it are expected, but monolithic layer rupture is very hard to predict. In a past few years a practice of analyzing state of deformation in high energy seismic tremors zones has been employed. It let gathering experience thanks to witch determination of dangerous shape of reformatted roof is possible. In the paper some typical forms of roof rocks deformations leading to seismic tremor occurrence will be presented. In general these are various types of multidirectional rock layers bending. Real examples of seismic events and rock bursts in the Czech Republic will be shown. 5 refs., 6 figs.

Theory and technology of rock excavation for civil engineering

CERN Document Server

Zou, Dingxiang

2017-01-01

This book summarizes the technical advances in recent decades and the various theories on rock excavation raised by scholars from different countries, including China and Russia. It not only focuses on rock blasting but also illustrates a number of non-blasting methods, such as mechanical excavation in detail. The book consists of 3 parts: Basic Knowledge, Surface Excavation and Underground Excavation. It presents a variety of technical methods and data from diverse sources in the book, making it a valuable theoretical and practical reference resource for engineers, researchers and postgraduates alike.

Application of NURE data to the study of crystalline rocks in the Wyoming uranium province

International Nuclear Information System (INIS)

Rush, S.M.; Anderson, J.R.; Bennett, J.E.

1983-03-01

The Wyoming uranium province study is a part of the National Uranium Resource Evaluation (NURE) program conducted by Bendix Field Engineering Corporation for the US Department of Energy. The ultimate objective of the entire project is the integration of NURE and other data sources to develop a model for a uranium province centered in Wyoming. This paper presents results of the first phase of the Wyoming uranium province study, which comprises characterization of the crystalline rocks of the study area using NURE hydrogeochemical and stream-sediment data, aerial radiometric and magnetic data, and new data generated for zircons from intrusive rocks in the study area. The results of this study indicate that the stream-sediment, aerial radiometric, aerial magnetic, and zircon data are useful in characterization of the crystalline rocks of the uranium province. The methods used in this project can be applied in two ways toward the recognition of a uranium province: (1) to locate major uranium deposits and occurrences, and (2) to generally identify different crystalline rock types, particularly those that could represent significant uranium source rocks. 14 figures, 8 tables

A Coupled Thermo-Hydro-Mechanical Model of Jointed Hard Rock for Compressed Air Energy Storage

Directory of Open Access Journals (Sweden)

Xiaoying Zhuang

2014-01-01

Full Text Available Renewable energy resources such as wind and solar are intermittent, which causes instability when being connected to utility grid of electricity. Compressed air energy storage (CAES provides an economic and technical viable solution to this problem by utilizing subsurface rock cavern to store the electricity generated by renewable energy in the form of compressed air. Though CAES has been used for over three decades, it is only restricted to salt rock or aquifers for air tightness reason. In this paper, the technical feasibility of utilizing hard rock for CAES is investigated by using a coupled thermo-hydro-mechanical (THM modelling of nonisothermal gas flow. Governing equations are derived from the rules of energy balance, mass balance, and static equilibrium. Cyclic volumetric mass source and heat source models are applied to simulate the gas injection and production. Evaluation is carried out for intact rock and rock with discrete crack, respectively. In both cases, the heat and pressure losses using air mass control and supplementary air injection are compared.

Geochemical behaviour of rare earth elements on metasomatic alteration of volcanic rocks

International Nuclear Information System (INIS)

Jordanov, J.A.; Kunov, A.J.

1987-01-01

Investigations are carried out on metasomatically altered Paleogene latites in order to follow up the rare earth elements (REE) geochemical behavour. Representative samples of the initial rocks (latites), from propylitized latites and quartz-sericite rocks, as well as from dickite, alumite, diaspore and monoquartzites, are analysed. The results show that REE have a behaviour of moderately mobile elements. They undergo redistribution both in quantity and in the composition of the group. The different concentrations and changes in the ΣREE compared to the initial rocks are observed and direct relationships to the degree of endogenic leaching are made. The REE mobility and redistribution during the metasomatic alterations in the region investigated are controlled by the physical-chemical conditions which play a significant role both in determining the composition of the mineral paragenese and in the fixing of REE. The distribution patterns indicate that REE redistribution in the case of metasomatic alterations is almost isochemical without any supply from hydrothermal solutions

Arrested diatreme development: Standing Rocks East, Hopi Buttes, Navajo Nation, USA

Science.gov (United States)

Lefebvre, Nathalie S.; White, James D. L.; Kjarsgaard, Bruce A.

2016-01-01

fluidal, folded-over shapes and ropy surfaces, subordinate thermally altered wall-rock and variegated domains of lapilli tuff. SRE shows a progressive transition from fissure to diatreme, and overall evolution from more explosive to weakly explosive eruption styles recorded at the conduit-crater transition. Diatreme development was initiated by deep-quarrying explosive eruptions along a fissure to form the country rock-rich breccia. Only parts of the fissure remained active as magma feeding the highly explosive eruptions along the fissure localized into discrete point sources forming the matrix-rich lapilli tuff deposits. These superimposed deposits record the passage of multiple debris-jets and subvertical fallback from shallow cratering arising from explosions triggered by magma-water interaction at numerous, discrete sites. However, instead of continuing to build a well-formed diatreme, the system switched to weak spattering with intermittent explosive activity and near-surface dike emplacement into the unconsolidated anisotropic, pyroclastic debris of the crater floor. Dominant spatter from strombolian-style bursts accumulated on the topographically varied, evolving unstable syn-eruptive crater floor, and led to local failure and remobilization. This study demonstrates how the combination of fissure behavior and sensitivity of the shallow plumbing system to local conditions during an eruption can lead to a decrease in eruptive footprint within the diatreme structure, and an overall decrease in explosivity resulting in the arrested development of an immature diatreme.

Clay club catalogue of characteristics of argillaceous rocks

International Nuclear Information System (INIS)

2005-01-01

The OECD/NEA Working Group on the Characterisation, the Understanding and the Performance of Argillaceous Rocks as Repository Host Formations, namely the Clay Club, examines the various argillaceous rocks that are being considered for the deep geological disposal of radioactive waste, i.e. from plastic, soft, poorly indurated clays to brittle, hard mud-stones or shales. The Clay Club considered it necessary and timely to provide a catalogue to gather in a structured way the key geo-scientific characteristics of the various argillaceous formations that are - or were - studied in NEA member countries with regard to radioactive waste disposal. The present catalogue represents the outcomes of this Clay Club initiative. (author)

Magnesium Isotopic Evidence for Ancient Subducted Oceanic Crust in LOMU-Like Potassium-Rich Volcanic Rocks

Science.gov (United States)

Sun, Yang; Teng, Fang-Zhen; Ying, Ji-Feng; Su, Ben-Xun; Hu, Yan; Fan, Qi-Cheng; Zhou, Xin-Hua

2017-10-01

To evaluate the role of subducted oceanic crust in the genesis of potassium-rich magmas, we report high-precision Mg isotopic data for a set of Cenozoic volcanic rocks from Northeast China. These rocks overall are lighter in Mg isotopic composition than the normal mantle and display considerable Mg isotopic variations, with δ26Mg ranging from -0.61 to -0.23. The covariation of δ26Mg with TiO2 in these rocks suggests that their light Mg isotopic compositions were derived from recycled oceanic crust in the form of carbonated eclogite in the source region. The strong correlations between δ26Mg and (Gd/Yb)N ratio as well as Sr-Pb isotopes further indicate a multicomponent and multistage origin of these rocks. Magnesium isotopes may thus be used as a novel tracer of recycled oceanic crust in the source region of mantle-derived magmas.

Rock Art

Science.gov (United States)

Henn, Cynthia A.

2004-01-01

There are many interpretations for the symbols that are seen in rock art, but no decoding key has ever been discovered. This article describes one classroom's experiences with a lesson on rock art--making their rock art and developing their own personal symbols. This lesson allowed for creativity, while giving an opportunity for integration…

DEPOSITIONAL ENVIRONMENT AND ORGANIC GEOCHEMICAL CHARACTERISTICS OF LOWER EOCENE BITUMINOUS ROCKS, IN THE KÜRNÜÇ/GÖYNÜK-BOLU AREA

Directory of Open Access Journals (Sweden)

Ali SARI

2016-12-01

Full Text Available In this study, dark gray and dark brown colored, organic-carbon rich bituminous rocks (bituminous marl and bituminous shale exposing around the Kürnüç area (Göynük, Bolu are investigated by means of or- ganic geochemical characteristics. In this respect, rock lithologies, depositional environments, rock source potential, kerogen and organic maturity types and hydrocarbon generation potentials of bituminous rocks were determined. For this reason, pyrolysis (Rock Eval–VI analysis, gas chromatography (GC and gas chromatography-mass spectrometer (GC-MS analyses were carried out. In addition, spore color index (SCI was determined with organic petrographic method and stable carbon analysis (δ13C of the samples were also conducted. Lithology of the studied samples is of clastic source and the depositional environ- ment is a lagoon with a partial connection to the sea. In bituminous rocks with excellent source rock potential TOC values are in the range of 2.52-8.38 wt % (average 6.08 wt %. With the exception of two samples (Type II kerogen type of all samples is Type I. According to pyrolysis, GC and GC-MS organic maturity results, all the samples are in immature stage. Organic geochemical data indicate that bituminous rocks have an excellent oil generation potential and there is no organic contamination.

Do Hf isotopes in magmatic zircons represent those of their host rocks?

Science.gov (United States)

Wang, Di; Wang, Xiao-Lei; Cai, Yue; Goldstein, Steven L.; Yang, Tao

2018-04-01

Lu-Hf isotopic system in zircon is a powerful and widely used geochemical tracer in studying petrogenesis of magmatic rocks and crustal evolution, assuming that zircon Hf isotopes can represent initial Hf isotopes of their parental whole rock. However, this assumption may not always be valid. Disequilibrium partial melting of continental crust would preferentially melt out non-zircon minerals with high time-integrated Lu/Hf ratios and generate partial melts with Hf isotope compositions that are more radiogenic than those of its magma source. Dissolution experiments (with hotplate, bomb and sintering procedures) of zircon-bearing samples demonstrate this disequilibrium effect where partial dissolution yielded variable and more radiogenic Hf isotope compositions than fully dissolved samples. A case study from the Neoproterozoic Jiuling batholith in southern China shows that about half of the investigated samples show decoupled Hf isotopes between zircons and the bulk rocks. This decoupling could reflect complex and prolonged magmatic processes, such as crustal assimilation, magma mixing, and disequilibrium melting, which are consistent with the wide temperature spectrum from ∼630 °C to ∼900 °C by Ti-in-zircon thermometer. We suggest that magmatic zircons may only record the Hf isotopic composition of their surrounding melt during crystallization and it is uncertain whether their Hf isotopic compositions can represent the primary Hf isotopic compositions of the bulk magmas. In this regard, using zircon Hf isotopic compositions to trace crustal evolution may be biased since most of these could be originally from disequilibrium partial melts.

Hydrology of some deep mines in Precambrian rocks

International Nuclear Information System (INIS)

Yardley, D.H.

1975-10-01

A number of underground mines were investigated during the summer of 1975. All of them are in Precambrian rocks of the Lake Superior region. They represent a variety of geologic settings. The purpose of the investigations was to make a preliminary study of the dryness, or lack of dryness of these rocks at depth. In other words, to see if water was entering the deeper workings through the unmined rock by some means such as fracture or fault zones, joints or permeable zones. Water entering through old mine workings extending to, or very near to the surface, or from the drilling equipment, was of interest only insofar as it might mask any water whose source was through the hanging or footwall rocks. No evidence of running, seeping or moving water was seen or reported at depths exceeding 3,000 feet. At depths of 3,000 feet or less, water seepages do occur in some of the mines, usually in minor quantities but increased amounts occur as depth becomes less. Others are dry at 2,000 feet of depth. Rock movements associated with extensive mining should increase the local secondary permeability of the rocks adjoining the mined out zones. Also most ore bodies are located where there has been a more than average amount of faulting, fracturing, and folding during the geologic past. They tend to cluster along crustal flows. In general, Precambrian rocks of similar geology, to those seen, well away from zones that have been disturbed by extensive deep mining, and well away from the zones of more intense geologic activity ought to be even less permeable than their equivalents in a mining district

Hydrology of some deep mines in Precambrian rocks

Energy Technology Data Exchange (ETDEWEB)

Yardley, D.H.

1975-10-01

A number of underground mines were investigated during the summer of 1975. All of them are in Precambrian rocks of the Lake Superior region. They represent a variety of geologic settings. The purpose of the investigations was to make a preliminary study of the dryness, or lack of dryness of these rocks at depth. In other words, to see if water was entering the deeper workings through the unmined rock by some means such as fracture or fault zones, joints or permeable zones. Water entering through old mine workings extending to, or very near to the surface, or from the drilling equipment, was of interest only insofar as it might mask any water whose source was through the hanging or footwall rocks. No evidence of running, seeping or moving water was seen or reported at depths exceeding 3,000 feet. At depths of 3,000 feet or less, water seepages do occur in some of the mines, usually in minor quantities but increased amounts occur as depth becomes less. Others are dry at 2,000 feet of depth. Rock movements associated with extensive mining should increase the local secondary permeability of the rocks adjoining the mined out zones. Also most ore bodies are located where there has been a more than average amount of faulting, fracturing, and folding during the geologic past. They tend to cluster along crustal flows. In general, Precambrian rocks of similar geology, to those seen, well away from zones that have been disturbed by extensive deep mining, and well away from the zones of more intense geologic activity ought to be even less permeable than their equivalents in a mining district.

Statistical damage constitutive model for rocks subjected to cyclic stress and cyclic temperature

Science.gov (United States)

Zhou, Shu-Wei; Xia, Cai-Chu; Zhao, Hai-Bin; Mei, Song-Hua; Zhou, Yu

2017-10-01

A constitutive model of rocks subjected to cyclic stress-temperature was proposed. Based on statistical damage theory, the damage constitutive model with Weibull distribution was extended. Influence of model parameters on the stress-strain curve for rock reloading after stress-temperature cycling was then discussed. The proposed model was initially validated by rock tests for cyclic stress-temperature and only cyclic stress. Finally, the total damage evolution induced by stress-temperature cycling and reloading after cycling was explored and discussed. The proposed constitutive model is reasonable and applicable, describing well the stress-strain relationship during stress-temperature cycles and providing a good fit to the test results. Elastic modulus in the reference state and the damage induced by cycling affect the shape of reloading stress-strain curve. Total damage induced by cycling and reloading after cycling exhibits three stages: initial slow increase, mid-term accelerated increase, and final slow increase.

30 CFR 717.15 - Disposal of excess rock and earth materials on surface areas.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Disposal of excess rock and earth materials on surface areas. 717.15 Section 717.15 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR INITIAL PROGRAM REGULATIONS UNDERGROUND MINING GENERAL PERFORMANCE STANDARDS § 717.15 Disposal of excess rock and...

Radioactive safety analysis and assessment of waste rock pile site in uranium tailings

International Nuclear Information System (INIS)

Liu Changrong; Liu Zehua; Wang Zhiyong; Zhou Xinghuo

2007-01-01

Based on theoretical calculation and in-situ test results, distribution and emissions of radioactive nuclides of uranium tailings impoundment and waste rock pile sites are analyzed in this paper. It is pointed out that 222 Rn is the main nuclide of uranium tailings impoundment and waste rock pile site. Also 222 Rn is the main source term of public dose. 222 Rn concentrations in the atmospheric environment around and individual dose to Rn gradually decrease with increasing distances to uranium tailings impoundment and waste rock pile site. Based on in-situ tests on five uranium tailings impoundment and waste rock pile sites, a decisive method and safety protection distance are presented, which can be used to guide the validation and design of radioactive safety protection in uranium tailings impoundment and waste rock pile sites. (authors)

An experimental investigation of geochromatography during secondary migration of petroleum performed under subsurface conditions with a real rock

Directory of Open Access Journals (Sweden)

Larter Steve

2000-10-01

Full Text Available An understanding of the size of petroleum secondary migration systems is vital for successful exploration for petroleum reserves. Geochemists have suggested that compositional fractionation of petroleum accompanying the migration process (geochromatography can potentially be used to infer distances petroleum may have travelled and the ratio of oil in the reservoir to that lost in the carrier. To date, this has been attempted by measuring concentrations and distributions of specific steranes, and aromatic oxygen and nitrogen compounds in reservoired oils which have been proposed to respond to migration rather than to source maturity or other effects. We report here an experiment involving oil migration through an initially water wet siltstone under realistic subsurface carrier bed or reservoir conditions (48 MPa, 70°C where source facies and maturity effects are eliminated. We show that geochromatography does indeed occur even for initially water-saturated rocks and that the migration fractionations observed for alkylcarbazoles, benzocarbazoles and alkylphenols are very similar to those seen in field data sets. In contrast, sterane based migration parameters show no compositional fractionation under these conditions.

Influence of the rock heterogeneity on the results of gamma-gamma logging

International Nuclear Information System (INIS)

Umiastowski, K.; Buniak, M.

1977-01-01

The influence of the grain size of granular rock and that of the empty holes size of porous rock on the results of gamma-gamma measurements was investigated. Monte-Carlo calculations and experiments were performed to establish this influence. For the grain (or empty holes) size greater than about 10mm the significant influence on the results of density measurements was found if a 137 Cs source was used. This effect is greater for the dry rock than for the water-saturated one. Formulae enabling the correct density value to be found, if the grain size is known, were proposed. (author)

Radiogeochemical characteristic of rocks of the Crimea peninsula and some principles of sedimentation

International Nuclear Information System (INIS)

Gherasimov, Yu.G.

1983-01-01

Radiogeochemical mapping with rock sampling of profiles, crossing all main structural facies zones of the Crimea peninsula was conducted. 1000 samples were taken. Uranium determination in samples was performed by fluorescence method (2 g/t threshold sensitivity). The distributions of U and Th background contents in rocks of the Crimea were tabulated. Maps of sampling of geological formations and distribution of U and Th background contents in rocks are given. It is shown that radioelement content in Crimea rocks is for the most part lower than clark one: 1.3-2.1 g/t contents prevail for U, Th contents don't exceed 12 g/t. Closeness of some radiogeochemical parameters points to the formation of terrigenous Crimea rocks due to removal of the material from the Ukrainian shield. Reworking of initial terrigenous material by hypergene processes led to U and Th separation, as well as to enrichment of younger sedimentary rocks with uranium