WorldWideScience

Sample records for source reductions part

  1. TSUNAMI INFORMATION SOURCES PART 3

    Directory of Open Access Journals (Sweden)

    Robert L. Wiegel

    2009-01-01

    Full Text Available This is Part 3 of Tsunami Information Sources published by Robert L. Wiegel, as Technical Report UCB/HEL 2006-3 of the Hydraulic Engineering Laboratory of the Department of Civil & Environmental Engineering of the University of California at Berkeley. Part 3 is published in "SCIENCE OF TSUNAMI HAZARDS" -with the author's permission -so that it can receive wider distribution and use by the Tsunami Scientific Community.

  2. Radiation Dose Reduction of Chest CT with Iterative Reconstruction in Image Space - Part I: Studies on Image Quality Using Dual Source CT

    International Nuclear Information System (INIS)

    Hwang, Hye Jeon; Seo, Joon Beom; Lee, Jin Seong; Song, Jae Woo; Lee, Hyun Joo; Lim, Chae Hun; Kim, Song Soo

    2012-01-01

    To determine whether the image quality (IQ) is improved with iterative reconstruction in image space (IRIS), and whether IRIS can be used for radiation reduction in chest CT. Standard dose chest CT (SDCT) in 50 patients and low dose chest CT (LDCT) in another 50 patients were performed, using a dual-source CT, with 120 kVp and same reference mAs (50 mAs for SDCT and 25 mAs for LDCT) employed to both tubes by modifying a dual-energy scan mode. Full-dose data were obtained by combining the data from both tubes and half-dose data were separated from a single tube. These were reconstructed by using a filtered back projection (FBP) and IRIS: full-dose FBP (F-FBP); full-dose IRIS (F-IRIS); half-dose FBP (H-FBP) and half-dose IRIS (H-IRIS). Objective noise was measured. The subjective IQ was evaluated by radiologists for the followings: noise, contrast and sharpness of mediastinum and lung. Objective noise was significantly lower in H-IRIS than in F-FBP (p < 0.01). In both SDCT and LDCT, the IQ scores were highest in F-IRIS, followed by F-FBP, H-IRIS and H-FBP, except those for sharpness of mediastinum, which tended to be higher in FBP. When comparing CT images between the same dose and different reconstruction (F-IRIS/F-FBP and H-IRIS/H-FBP) algorithms, scores tended to be higher in IRIS than in FBP, being more distinct in half-dose images. However, despite the use of IRIS, the scores were lower in H-IRIS than in F-FBP. IRIS generally helps improve the IQ, being more distinct at the reduced radiation. However, reduced radiation by half results in IQ decrease even when using IRIS in chest CT.

  3. TSUNAMI INFORMATION SOURCES PART 2

    Directory of Open Access Journals (Sweden)

    Robert L. Wiegel

    2006-01-01

    Full Text Available Tsunami Information Sources (Robert L. Wiegel, University of California, Berkeley, CA, UCB/HEL 2005-1, 14 December 2005, 115 pages, is available in printed format, and on a diskette. It is also available in electronic format at the Water Resources Center Archives, University of California, Berkeley, CA http:www.lib.berkeley.edu/WRCA/tsunamis.htmland in the International Journal of The Tsunami Society, Science of Tsunami Hazards (Vol. 24, No. 2, 2006, pp 58-171 at http://www.sthjournal.org/sth6.htm.This is Part 2 of the report. It has two components. They are: 1.(Sections A and B. Sources added since the first report, and corrections to a few listed in the first report. 2.(Sections C and D. References from both the first report and this report, listed in two categories:Section C. Planning and engineering design for tsunami mitigation/protection; adjustments to the hazard; damage to structures and infrastructureSection D. Tsunami propagation nearshore; induced oscillations; runup/inundation (flooding and drawdown.

  4. EDF source term reduction project main outcomes and further developments

    International Nuclear Information System (INIS)

    Ranchoux, Gilles; Bonnefon, Julien; Benfarah, Moez; Wintergerst Matthieu; Gressier, Frederic; Leclercq, Stephanie

    2012-09-01

    The dose reduction is a strategic purpose for EDF in link with the stakes of, nuclear acceptability, respect of regulation and productivity gains. This consists not only in improving the reactor shutdown organization (time spent in control area, biological shielding,...) but also in improving the radiological state of the unit and the efficiency of the source term reduction operations. Since 2003, EDF has been running an innovative project called 'Source Term Reduction' federating the different EDF research and engineering centers in order to: - participate to the long term view about Radiological Protection issues (international feedback analyses), - develop contamination prediction tools (OSCAR software) suitable for the industrial needs (operating units and EPR design), - develop scientific models useful for the understanding of contamination mechanisms to support the strategic decision processes, - carry on with updating and analyzing of contamination measurements feedback in corrosion products (EMECC and CZT campaigns), - carry on with the operational support at short or middle term by optimizing startup and shutdown processes, pre-oxidation or and by improving purification efficiency or material characteristics. This paper will show in a first part the main 2011 results in occupational exposure (collective and individual dose, RCS index...). In a second part, an overview of the main EDF outcomes of the last 3 years in the field of source term reduction will be presented. Future developments extended to contamination issues in EDF NPPs will be also pointed out in this paper. (authors)

  5. Counting master integrals: Integration by parts vs. differential reduction

    International Nuclear Information System (INIS)

    Kalmykov, Mikhail Yu.; Kniehl, Bernd A.

    2011-01-01

    The techniques of integration by parts and differential reduction differ in the counting of master integrals. This is illustrated using as an example the two-loop sunset diagram with on-shell kinematics. A new algebraic relation between the master integrals of the two-loop sunset diagram that does not follow from the standard integration-by-parts technique is found.

  6. Counting master integrals. Integration by parts vs. differential reduction

    International Nuclear Information System (INIS)

    Kalmykov, Mikhail Yu; Kniehl, Bernd A.

    2011-05-01

    The techniques of integration by parts and differential reduction differ in the counting of master integrals. This is illustrated using as an example the two- loop sunset diagram with on-shell kinematics. A new algebraic relation between the master integrals of the two-loop sunset diagram that does not follow from the integration-by-parts technique is found. (orig.)

  7. Source Reduction Effectiveness at Fuel Contaminated Sites, Technical Summary Report

    National Research Council Canada - National Science Library

    2000-01-01

    This report assesses the degree to which various types or engineered source-reduction efforts at selected fuel-contaminated sites have resulted in decreasing concentrations of fuel constituents dissolved in groundwater...

  8. Current Concepts in the Mandibular Condyle Fracture Management Part II: Open Reduction Versus Closed Reduction

    OpenAIRE

    Choi, Kang-Young; Yang, Jung-Dug; Chung, Ho-Yun; Cho, Byung-Chae

    2012-01-01

    In the treatment of mandibular condyle fracture, conservative treatment using closed reduction or surgical treatment using open reduction can be used. Management of mandibular condylar fractures remains a source of ongoing controversy in oral and maxillofacial trauma. For each type of condylar fracture,the treatment method must be chosen taking into consideration the presence of teeth, fracture height, patient'sadaptation, patient's masticatory system, disturbance of occlusal function, and de...

  9. California Air Resources board's mobil source emission reduction credit guidelines

    International Nuclear Information System (INIS)

    Dunwoody Lentz, C.; Werner, B.

    1993-01-01

    The California Air Resources Board has developed guidance for the generation and use of mobil source emission reduction credits. Mobil source credits can be used to improve air quality, or to mitigate increases in emissions associated with industrial and non-industrial sources. They are created by programs which reduce mobile source emission beyond the reductions required by federal, state, and local laws or air quality attainment plans. Significant amounts of credit can be generated by some types of programs which reduce mobile source emissions of oxides of nitrogen (NO x ) and reactive organic gases (ROG). Mobile source credit programs must be carefully structured to ensure that emission reductions are real, accurately quantified, enforceable, and have a defined life. Three potentially feasible programs for the creation of mobile source credits include accelerated retirement of older vehicles, purchase of low-emission buses, and purchase of zero-emission vehicles. These programs are evaluated for their ability to generate credit and to assess their cost effectiveness. Based on the examples presented, two methods of generating mobile source credits, the accelerated retirement of older vehicles and the purchase of low-emission buses, appear to be cost-effective when compared to other emission control measures

  10. Greenhouse effect gases sources and sinks (CO2, CH4, N2O) in grasslands and reduction strategies. Greenhouse effect gases prairies. Final report of the second part of the project. April 2004

    International Nuclear Information System (INIS)

    Soussana, J.F.

    2004-04-01

    The project 'GES-Prairies' (Greenhouse Gases - Grasslands) had two main objectives: 1. To measure more accurately the fluxes of CO 2 , CH 4 and N 2 O of French grasslands and determine the greenhouse gas (GHG) balance of these areas. 2. To calculate the net GHG emissions of cattle production farms and finally to propose and evaluate some management scenarios leading to a reduction of GHG emissions. This project deals with three different spatial scales: the field scale, the farm scale and finally, the regional scale. At the field scale, during two years, fluxes of CO 2 , CH 4 and N 2 O were measured in a mid-mountain permanent grassland, previously managed intensively by cutting and grazing (Laqueuille, Auvergne, France). Results from the first complete year of measurements show that the extensification process (reduction of the stocking rate and stopping N fertilization) allows to stock more carbon in the ecosystem. At the farm scale, We developed a model (FARMSIM, coupled to PASIM) able to simulate the GHG balance of a livestock farm. FARMSIM has been tested with data obtained from a mixed livestock farm in Lorraine (dairy and meat production, annual average stocking rate = 1.3 LU ha -1 ) of 100 ha (including 76 ha of grasslands and 21 of annual crops). The results indicate a net emission of 175 t equivalent C-CO 2 for this farm. If expressed per unit of product, it represents 1.34 t equivalent C-CO 2 per LU and per year or 0.54 kg CO 2 per kg of milk and per year. At the regional scale/. The PASIM model has been used to simulate the European grasslands with a spatial resolution of 1' (about 200 * 200 km). For each grid cell, a sensibility analysis allowed to determine the N application which correspond to 30% of the N application that would maximize the annual yield of the pasture. Simulation runs on mixed systems (combining grazing and cutting) show that almost one half of the grassland area is, on average, used for cutting. These simulations predict N 2 O

  11. Ozone reduction strategy for the northeastern part of Austria: cooperation and compilation of the fundamentals

    International Nuclear Information System (INIS)

    Orthofer, R.; Winiwarter, W.

    1996-05-01

    This report is contribution to the implementation of an ozone reduction strategy for the northeastern part of Austria. The report contains a regional emission inventory, an emission projection for the years 1996, 2001 and 2006, an evaluation of further stationary sources reduction options. The ozone formation potentials of non-methane volatile organic compounds (NMVOC) emissions were calculated separately for both mobile and stationary source group, in order to assess the respective contribution to the local ozone formation. It can be shown that status-quo reduction measures are more efficient in terms of ozone formation potential during the summer season than in terms of NMVOC emission mass reduction. It is recommended that further NMVOC emission control should focus primarily on industrial solvent emissions, domestic heating of water during summertime with solid fuels, and on stubble burning in the fields. (author)

  12. Agroforestry buffers for nonpoint source pollution reductions from agricultural watersheds.

    Science.gov (United States)

    Udawatta, Ranjith P; Garrett, Harold E; Kallenbach, Robert

    2011-01-01

    Despite increased attention and demand for the adoption of agroforestry practices throughout the world, rigorous long-term scientific studies confirming environmental benefits from the use of agroforestry practices are limited. The objective was to examine nonpoint-source pollution (NPSP) reduction as influenced by agroforestry buffers in watersheds under grazing and row crop management. The grazing study consists of six watersheds in the Central Mississippi Valley wooded slopes and the row crop study site consists of three watersheds in a paired watershed design in Central Claypan areas. Runoff water samples were analyzed for sediment, total nitrogen (TN), and total phosphorus (TP) for the 2004 to 2008 period. Results indicate that agroforestry and grass buffers on grazed and row crop management sites significantly reduce runoff, sediment, TN, and TP losses to streams. Buffers in association with grazing and row crop management reduced runoff by 49 and 19%, respectively, during the study period as compared with respective control treatments. Average sediment loss for grazing and row crop management systems was 13.8 and 17.9 kg ha yr, respectively. On average, grass and agroforestry buffers reduced sediment, TN, and TP losses by 32, 42, and 46% compared with the control treatments. Buffers were more effective in the grazing management practice than row crop management practice. These differences could in part be attributed to the differences in soils, management, and landscape features. Results from this study strongly indicate that agroforestry and grass buffers can be designed to improve water quality while minimizing the amount of land taken out of production. American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America.

  13. Renewable energy sources '91. Part 3

    International Nuclear Information System (INIS)

    Michalicka, L.

    1991-01-01

    Part 3 of the proceedings contains a report on the conference and 10 contributions, out of which 2 have been inputted in INIS: one deals with the economic problems of wind-, solar- and oil-driven water pumps, the other deals with the decrease in sunshine brought about by the operation of Czechoslovak nuclear power plants. (M.D.). 4 tabs., 10 figs., 10 refs

  14. Reduction Assessment of Agricultural Non-Point Source Pollutant Loading

    OpenAIRE

    Fu, YiCheng; Zang, Wenbin; Zhang, Jian; Wang, Hongtao; Zhang, Chunling; Shi, Wanli

    2018-01-01

    NPS (Non-point source) pollution has become a key impact element to watershed environment at present. With the development of technology, application of models to control NPS pollution has become a very common practice for resource management and Pollutant reduction control in the watershed scale of China. The SWAT (Soil and Water Assessment Tool) model is a semi-conceptual model, which was put forward to estimate pollutant production & the influences on water quantity-quality under different...

  15. Landscape planning for agricultural nonpoint source pollution reduction III: Assessing phosphorus and sediment reduction potential

    Science.gov (United States)

    Diebel, M.W.; Maxted, J.T.; Robertson, Dale M.; Han, S.; Vander Zanden, M. J.

    2009-01-01

    Riparian buffers have the potential to improve stream water quality in agricultural landscapes. This potential may vary in response to landscape characteristics such as soils, topography, land use, and human activities, including legacies of historical land management. We built a predictive model to estimate the sediment and phosphorus load reduction that should be achievable following the implementation of riparian buffers; then we estimated load reduction potential for a set of 1598 watersheds (average 54 km2) in Wisconsin. Our results indicate that land cover is generally the most important driver of constituent loads in Wisconsin streams, but its influence varies among pollutants and according to the scale at which it is measured. Physiographic (drainage density) variation also influenced sediment and phosphorus loads. The effect of historical land use on present-day channel erosion and variation in soil texture are the most important sources of phosphorus and sediment that riparian buffers cannot attenuate. However, in most watersheds, a large proportion (approximately 70%) of these pollutants can be eliminated from streams with buffers. Cumulative frequency distributions of load reduction potential indicate that targeting pollution reduction in the highest 10% of Wisconsin watersheds would reduce total phosphorus and sediment loads in the entire state by approximately 20%. These results support our approach of geographically targeting nonpoint source pollution reduction at multiple scales, including the watershed scale. ?? 2008 Springer Science+Business Media, LLC.

  16. Reduction at the source of household wastes: why not trying the inciting tariffing?; La reduction a la source des dechets menagers: pourquoi ne pas essayer la tarification incitative?

    Energy Technology Data Exchange (ETDEWEB)

    Glachant, M.

    2002-11-01

    This article discusses how the existing financing tools of the household wastes management implemented in France can be changed to become inciting tools for the reduction of the volume of wastes at the source. It comprises 5 parts: the first part presents the present day way of financing of the public utility of household wastes in France and discusses its (very modest) inciting effect. In the next two parts the possible modalities to make it more inciting are discussed. These parts stresses on two questions: is it better to charge the upstream producers via contributions to chartered companies or to charge the downstream households via volume- or weight-proportional fees? How much should they pay? Then some experiences of inciting tariffing are briefly reviewed: the Duales German system of upstream charging and the US and Dutch downstream charging systems. (J.S.)

  17. Current Concepts in the Mandibular Condyle Fracture Management Part II: Open Reduction Versus Closed Reduction

    Science.gov (United States)

    Yang, Jung-Dug; Chung, Ho-Yun; Cho, Byung-Chae

    2012-01-01

    In the treatment of mandibular condyle fracture, conservative treatment using closed reduction or surgical treatment using open reduction can be used. Management of mandibular condylar fractures remains a source of ongoing controversy in oral and maxillofacial trauma. For each type of condylar fracture,the treatment method must be chosen taking into consideration the presence of teeth, fracture height, patient'sadaptation, patient's masticatory system, disturbance of occlusal function, and deviation of the mandible. In the past, closed reduction with concomitant active physical therapy conducted after intermaxillary fixation during the recovery period had been mainly used, but in recent years, open treatment of condylar fractures with rigid internal fixation has become more common. The objective of this review was to evaluate the main variables that determine the choice of an open or closed method for treatment of condylar fractures, identifying their indications, advantages, and disadvantages, and to appraise the current evidence regarding the effectiveness of interventions that are used in the management of fractures of the mandibular condyle. PMID:22872831

  18. Current Concepts in the Mandibular Condyle Fracture Management Part II: Open Reduction Versus Closed Reduction

    Directory of Open Access Journals (Sweden)

    Kang-Young Choi

    2012-07-01

    Full Text Available In the treatment of mandibular condyle fracture, conservative treatment using closed reduction or surgical treatment using open reduction can be used. Management of mandibular condylar fractures remains a source of ongoing controversy in oral and maxillofacial trauma. For each type of condylar fracture,the treatment method must be chosen taking into consideration the presence of teeth, fracture height, patient'sadaptation, patient's masticatory system, disturbance of occlusal function, and deviation of the mandible. In the past, closed reduction with concomitant active physical therapy conducted after intermaxillary fixation during the recovery period had been mainly used, but in recent years, open treatment of condylar fractures with rigid internal fixation has become more common. The objective of this review was to evaluate the main variables that determine the choice of an open or closed method for treatment of condylar fractures, identifying their indications, advantages, and disadvantages, and to appraise the current evidence regarding the effectiveness of interventions that are used in the management of fractures of the mandibular condyle.

  19. Reductive dechlorination of trichloroethene DNAPL source zones: source zone architecture versus electron donor availability

    Science.gov (United States)

    Krol, M.; Kokkinaki, A.; Sleep, B.

    2014-12-01

    The persistence of dense-non-aqueous-phase liquids (DNAPLs) in the subsurface has led practitioners and regulatory agencies to turn towards low-maintenance, low-cost remediation methods. Biological degradation has been suggested as a possible solution, based on the well-proven ability of certain microbial species to break down dissolved chlorinated ethenes under favorable conditions. However, the biodegradation of pure phase chlorinated ethenes is subject to additional constraints: the continuous release of electron acceptor at a rate governed by mass transfer kinetics, and the temporal and spatial heterogeneity of DNAPL source zones which leads to spatially and temporally variable availability of the reactants for reductive dechlorination. In this work, we investigate the relationship between various DNAPL source zone characteristics and reaction kinetics using COMPSIM, a multiphase groundwater model that considers non-equilibrium mass transfer and Monod-type kinetics for reductive dechlorination. Numerical simulations are performed for simple, homogeneous trichloroethene DNAPL source zones to demonstrate the effect of single source zone characteristics, as well as for larger, more realistic heterogeneous source zones. It is shown that source zone size, and mass transfer kinetics may have a decisive effect on the predicted bio-enhancement. Finally, we evaluate the performance of DNAPL bioremediation for realistic, thermodynamically constrained, concentrations of electron donor. Our results indicate that the latter may be the most important limitation for the success of DNAPL bioremediation, leading to reduced bio-enhancement and, in many cases, comparable performance with water flooding.

  20. Current Concepts in the Mandibular Condyle Fracture Management Part II: Open Reduction Versus Closed Reduction

    Directory of Open Access Journals (Sweden)

    Kang-Young Choi

    2012-07-01

    Full Text Available In the treatment of mandibular condyle fracture, conservative treatment using closedreduction or surgical treatment using open reduction can be used. Management of mandibularcondylar fractures remains a source of ongoing controversy in oral and maxillofacial trauma.For each type of condylar fracture,the treatment method must be chosen taking intoconsideration the presence of teeth, fracture height, patient’sadaptation, patient’s masticatorysystem, disturbance of occlusal function, and deviation of the mandible. In the past, closedreduction with concomitant active physical therapy conducted after intermaxillary fixationduring the recovery period had been mainly used, but in recent years, open treatment ofcondylar fractures with rigid internal fixation has become more common. The objectiveof this review was to evaluate the main variables that determine the choice of an open orclosed method for treatment of condylar fractures, identifying their indications, advantages,and disadvantages, and to appraise the current evidence regarding the effectiveness ofinterventions that are used in the management of fractures of the mandibular condyle.

  1. Impedance-Source Networks for Electric Power Conversion Part II

    DEFF Research Database (Denmark)

    Siwakoti, Yam P.; Peng, Fang Zheng; Blaabjerg, Frede

    2015-01-01

    Impedance-source networks cover the entire spectrum of electric power conversion applications (dc-dc, dc-ac, ac-dc, ac-ac) controlled and modulated by different modulation strategies to generate the desired dc or ac voltage and current at the output. A comprehensive review of various impedance......-source-network-based power converters has been covered in a previous paper and main topologies were discussed from an application point of view. Now Part II provides a comprehensive review of the most popular control and modulation strategies for impedance-source network-based power converters/inverters. These methods...

  2. Impedance-Source Networks for Electric Power Conversion Part I

    DEFF Research Database (Denmark)

    Siwakoti, Yam P.; Peng, Fang Zheng; Blaabjerg, Frede

    2015-01-01

    power chain, which may improve the reliability and performance of the power system. The first part of this paper provides a comprehensive review of the various impedance-source-networks-based power converters and discusses the main topologies from an application point of view. This review paper...... is the first of its kind with the aim of providing a “one-stop” information source and a selection guide on impedance-source networks for power conversion for researchers, designers, and application engineers. A comprehensive review of various modeling, control, and modulation techniques for the impedance...

  3. Open reduction and internal fixation of three and four-part fractures of the proximal part of the humerus

    NARCIS (Netherlands)

    Wijgman, A. J.; Roolker, W.; Patt, T. W.; Raaymakers, E. L. F. B.; Marti, R. K.

    2002-01-01

    BACKGROUND: Controversy persists concerning the preferred treatment of displaced fractures of the proximal part of the humerus. The present study was undertaken to evaluate the results of open reduction and internal fixation of three and four-part fractures of the proximal part of the humerus and

  4. Bomb reduction of uranium tetrafluoride. Part II: Influence of the addition elements in the reduction process

    International Nuclear Information System (INIS)

    Anca Abati, R.; Lopez Rodriguez, M.

    1962-01-01

    This work shows the influence of uranium oxide and uranyl fluoride in the reduction of uranium with Ca and Mg. These additions are more harmful when using smaller bombs. The uranyl fluoride has influence in the reduction process; the curves yield-concentration shows two regions depending upon the salt concentration. The behaviour of this addition in these regions can be explained following the different decompositions that can take place during the reduction process. (Author) 9 refs

  5. Source term reduction at DAEC (including stellite ball recycling)

    International Nuclear Information System (INIS)

    Smith, R.; Schebler, D.

    1995-01-01

    The Duane Arnold Energy Center was seeking methods to reduce dose rates from the drywell due to Co-60. Duane Arnold is known in the industry to have one of the highest drywell dose rates from the industry standardized 'BRAC' point survey. A prime method to reduce dose rates due to Co-60 is the accelerated replacement of stellite pins and rollers in control rod blades due to their high stellite (cobalt) content. Usually the cobalt content in alloys of stellite is greater than 60% cobalt by weight. During the RFO-12 refueling outage at Duane Arnold, all of the remaining cobalt bearing control rod blades were replaced and new stellite free control rod blades were installed in the core. This left Duane Arnold with the disposal of highly radioactive stellite pins and rollers. The processing of control rod blades for disposal is a very difficult evolution. First, the velocity limiter (a bottom portion of the component) and the highly radioactive upper stellite control rod blade ins and rollers are separated from the control rod blade. Next, the remainder of the control rod blade is processed (chopped and/or crushed) to aid packaging the waste for disposal. The stellite bearings are then often carefully placed in with the rest of the waste in a burial liner to provide shielding for disposal or more often are left as 'orphans' in the spent fuel pool because their high specific activity create shipping and packaging problems. Further investigation by the utility showed that the stellite balls and pins could be recycled to a source manufacturer rather than disposed of in a low-level burial site. The cost savings to the utility was on the order of $200,000 with a gross savings of $400,000 in savings in burial site charges. A second advantage of the recycling of the stellite pins and rollers was a reduction in control in radioactive waste shipments

  6. Interpolation-Based Condensation Model Reduction Part 1: Frequency Window Reduction Method Application to Structural Acoustics

    National Research Council Canada - National Science Library

    Ingel, R

    1999-01-01

    .... Projection operators are employed for the model reduction or condensation process. Interpolation is then introduced over a user defined frequency window, which can have real and imaginary boundaries and be quite large. Hermitian...

  7. Radar-cross-section reduction of wind turbines. part 1.

    Energy Technology Data Exchange (ETDEWEB)

    Brock, Billy C.; Loui, Hung; McDonald, Jacob J.; Paquette, Joshua A.; Calkins, David A.; Miller, William K.; Allen, Steven E.; Clem, Paul Gilbert; Patitz, Ward E.

    2012-03-05

    In recent years, increasing deployment of large wind-turbine farms has become an issue of growing concern for the radar community. The large radar cross section (RCS) presented by wind turbines interferes with radar operation, and the Doppler shift caused by blade rotation causes problems identifying and tracking moving targets. Each new wind-turbine farm installation must be carefully evaluated for potential disruption of radar operation for air defense, air traffic control, weather sensing, and other applications. Several approaches currently exist to minimize conflict between wind-turbine farms and radar installations, including procedural adjustments, radar upgrades, and proper choice of low-impact wind-farm sites, but each has problems with limited effectiveness or prohibitive cost. An alternative approach, heretofore not technically feasible, is to reduce the RCS of wind turbines to the extent that they can be installed near existing radar installations. This report summarizes efforts to reduce wind-turbine RCS, with a particular emphasis on the blades. The report begins with a survey of the wind-turbine RCS-reduction literature to establish a baseline for comparison. The following topics are then addressed: electromagnetic model development and validation, novel material development, integration into wind-turbine fabrication processes, integrated-absorber design, and wind-turbine RCS modeling. Related topics of interest, including alternative mitigation techniques (procedural, at-the-radar, etc.), an introduction to RCS and electromagnetic scattering, and RCS-reduction modeling techniques, can be found in a previous report.

  8. ZVI-Clay remediation of a chlorinated solvent source zone, Skuldelev, Denmark: 2. Groundwater contaminant mass discharge reduction

    DEFF Research Database (Denmark)

    Fjordbøge, Annika Sidelmann; Lange, Ida Vedel; Bjerg, Poul Løgstrup

    2012-01-01

    The impact of source mass depletion on the down-gradient contaminant mass discharge was monitored for a 19-month period as a part of a field demonstration of the ZVI-Clay soil mixing remediation technology. Groundwater samples were collected from conventional monitoring wells (120 samples) and a ...... down-gradient contaminant mass discharge reduction (76%) for the parent compound (PCE), while the overall reduction of chlorinated ethenes was smaller (21%)....

  9. Greenhouse effect gases sources and sinks (CO{sub 2}, CH{sub 4}, N{sub 2}O) in grasslands and reduction strategies. Greenhouse effect gases prairies. Final report of the second part of the project. April 2004; Sources et puits de gaz a effet de serre (CO{sub 2}, CH{sub 4}, N{sub 2}O) en prairie paturee et strategies de reduction. GES-Prairies. Rapport final de la seconde tranche du projet. Avril 2004

    Energy Technology Data Exchange (ETDEWEB)

    Soussana, J.F

    2004-04-15

    The project 'GES-Prairies' (Greenhouse Gases - Grasslands) had two main objectives: 1. To measure more accurately the fluxes of CO{sub 2}, CH{sub 4} and N{sub 2}O of French grasslands and determine the greenhouse gas (GHG) balance of these areas. 2. To calculate the net GHG emissions of cattle production farms and finally to propose and evaluate some management scenarios leading to a reduction of GHG emissions. This project deals with three different spatial scales: the field scale, the farm scale and finally, the regional scale. At the field scale, during two years, fluxes of CO{sub 2}, CH{sub 4} and N{sub 2}O were measured in a mid-mountain permanent grassland, previously managed intensively by cutting and grazing (Laqueuille, Auvergne, France). Results from the first complete year of measurements show that the extensification process (reduction of the stocking rate and stopping N fertilization) allows to stock more carbon in the ecosystem. At the farm scale, We developed a model (FARMSIM, coupled to PASIM) able to simulate the GHG balance of a livestock farm. FARMSIM has been tested with data obtained from a mixed livestock farm in Lorraine (dairy and meat production, annual average stocking rate = 1.3 LU ha{sup -1}) of 100 ha (including 76 ha of grasslands and 21 of annual crops). The results indicate a net emission of 175 t equivalent C-CO{sub 2} for this farm. If expressed per unit of product, it represents 1.34 t equivalent C-CO{sub 2} per LU and per year or 0.54 kg CO{sub 2} per kg of milk and per year. At the regional scale/. The PASIM model has been used to simulate the European grasslands with a spatial resolution of 1' (about 200 * 200 km). For each grid cell, a sensibility analysis allowed to determine the N application which correspond to 30% of the N application that would maximize the annual yield of the pasture. Simulation runs on mixed systems (combining grazing and cutting) show that almost one half of the grassland area is, on

  10. Gastro-oesophageal reflux. Part 1: smoking and alcohol reduction.

    Science.gov (United States)

    Al Talalwah, Narmeen; Woodward, Sue

    Gastro-oesophageal reflux disease (GORD) is defined as an abnormal reflux of the stomach contents into the oesophagus, which provokes symptoms and impairs the quality of life. GORD has a high prevalence and incurs costs to the healthcare system. This is the first paper in a series of three exploring the conservative, medical and surgical treatment of GORD. This first paper presents a review of the effect of smoking and alcohol on reflux symptoms and the impact of smoking and alcohol reduction on symptoms of GORD. A search for English language studies on adults was conducted using three databases, MEDLINE, Embase and the Cochrane Central Register of Controlled Trials (CENTRAL). Eleven relevant studies were included in the review. The effect of alcohol on the stimulation of reflux has been debated over the years in different studies. Some studies state that alcohol consumption induces reflux and moderate amounts exacerbate nocturnal gastro-oesophageal heartburn reflux. However, other studies have found no association between alcohol consumption and reflux. Most reflux occurs during smoking because nicotine causes the lower oesophageal sphincter to relax, which increases the risk of reflux. Similarly, the number of cigarettes smoked is associated with the risk of reflux. Nurses need to be aware of the effect of smoking and alcohol on reflux to provide evidence-based advice to empower patients to change their lifestyle, which results in increased therapeutic compliance and a better clinical status. There is no evidence that reducing alcohol consumption decreases symptoms and only limited evidence on the effectiveness of smoking cessation. Further research into the effectiveness of these lifestyle modifications is therefore required.

  11. Uranium tetrafluoride reduction closed bomb. Part I: Reduction process general conditions

    International Nuclear Information System (INIS)

    Anca Abati, R.; Lopez Rodriguez, M.

    1961-01-01

    General conditions about the metallo thermic reduction in small bombs (250 and 800 gr. of uranium) has been investigated. Factors such as kind and granulometry of the magnesium used, magnesium excess and preheating temperature, which affect yields and metal quality have been considered. magnesium excess increased yields in a 15% in the small bomb, about the preheating temperature, there is a range between which yields and metal quality does not change. All tests have been made with graphite linings. (Author) 18 refs

  12. Stem cells in dentistry--part I: stem cell sources.

    Science.gov (United States)

    Egusa, Hiroshi; Sonoyama, Wataru; Nishimura, Masahiro; Atsuta, Ikiru; Akiyama, Kentaro

    2012-07-01

    Stem cells can self-renew and produce different cell types, thus providing new strategies to regenerate missing tissues and treat diseases. In the field of dentistry, adult mesenchymal stem/stromal cells (MSCs) have been identified in several oral and maxillofacial tissues, which suggests that the oral tissues are a rich source of stem cells, and oral stem and mucosal cells are expected to provide an ideal source for genetically reprogrammed cells such as induced pluripotent stem (iPS) cells. Furthermore, oral tissues are expected to be not only a source but also a therapeutic target for stem cells, as stem cell and tissue engineering therapies in dentistry continue to attract increasing clinical interest. Part I of this review outlines various types of intra- and extra-oral tissue-derived stem cells with regard to clinical availability and applications in dentistry. Additionally, appropriate sources of stem cells for regenerative dentistry are discussed with regard to differentiation capacity, accessibility and possible immunomodulatory properties. Copyright © 2012 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

  13. Reduction of phosphate ores by carbon: Part I. Process variables for design of rotary kiln system

    Science.gov (United States)

    Mu, Jacob; Leder, Frederic; Park, Won C.; Hard, Robert A.; Megy, Joseph; Reiss, Howard

    1986-12-01

    Feasibility is established for the reduction of phosphate ores in a rotary kiln, avoiding electric submerged arc furnace technology. This represents a totally new approach to phosphoric acid. Reduction rates of phosphate ore-silica mixtures by carbon in the temperature range of 1100 to 1500 °C under several CO partial pressures in nitrogen were measured in thermogravimetric analyzers. Parameters such as carbon and silica contents, particle and pellet sizes, and gas flow rate were also evaluated with various domestic and foreign phosphate ores. Furthermore, a variety of carbon sources such as subbituminous coals, bituminous coals, anthracite, petroleum coke, and metallurgical coke were tested as reducing agents. Thermodynamic considerations elucidate the temperature dependence of overall conversion as well as the role of excess silica in establishing equilibrium pressure. These findings provide the background for analysis of the kinetics of conversion in Part II of this work. These studies, in conjunction with a previously published work, indicate the importance of intergranular melt phases in the kinetics of otherwise solid state reactions.

  14. Economic Analysis of Nitrate Source Reductions in California Agriculture

    Science.gov (United States)

    Medellin-Azuara, J.; Howitt, R.; Rosenstock, T.; Harter, T.; Pettygrove, S. G.; Dzurella, K.; Lund, J. R.

    2011-12-01

    We present an analytical approach to assess the economic impact of improving nitrogen management practices in California agriculture. We employ positive mathematical programming to calibrate crop production to base input information. The production function representation is a nested constant elasticity of substitution with two nests: one for applied water and one for applied nitrogen. The first nest accounts for the tradeoffs between irrigation efficiency and capital investments in irrigation technology. The second nest represents the tradeoffs between nitrogen application efficiency and the marginal costs of improving nitrogen efficiency. In the production function nest, low elasticities of substitution and water and nitrogen stress constraints keep agricultural crop yields constant despite changes in nitrogen management practices. We use the Tulare Basin, and the Salinas Valley in California's Central Valley and Central Coast respectively as our case studies. Preliminary results show that initial reductions of 25% in nitrogen loads to groundwater may not impose large costs to agricultural crop production as substitution of management inputs results in only small declines in net revenue from farming and total land use. Larger reductions in the nitrogen load to groundwater of 50% imposes larger marginal costs for better nitrogen management inputs and reductions in the area of lower valued crops grown in the study areas. Despite the shortage of data on quantitative effects of improved nitrogen efficiency; our results demonstrate the potential of combining economic and agronomic data into a model that can reflect differences in cost and substitutabilty in nitrogen application methods, that can be used to reduce the quantity of nitrogen leaching into groundwater.

  15. Reduction of NOx emission from stationary combustion sources

    International Nuclear Information System (INIS)

    Nelson, P.F.

    1992-01-01

    The environmental impacts of NO x emission from stationary combustion sources are briefly described. These include the formation of both acid rain and photochemical smog, major environmental problems. The three mechanisms which have been identified for the formation of NO x in combustion (thermal, prompt and fuel) are also briefly outlined. Recently stringent standards have been introduced to control emissions of NO x and the review describes the major primary and secondary measures. 10 refs. 2 tabs., 5 figs

  16. Disaster Risk Reduction through Innovative Uses of Crowd Sourcing (Invited)

    Science.gov (United States)

    Berger, J.; Greene, M.

    2010-12-01

    Crowd sourcing can be described as a method of distributed problem-solving. It takes advantage of the power of the crowd, which can in some cases be a community of experts and in other cases the collective insight of a broader range of contributors with varying degrees of domain knowledge. The term crowd sourcing was first used by Jeff Howe in a June 2006 Wired magazine article “The Rise of Crowdsourcing,” and is a combination of the terms “crowd” and “outsourcing.” Some commonly known examples of crowd sourcing, in its broadest sense, include Wikepedia, distributed participatory design projects, and consumer websites such as Yelp and Angie’s List. The popularity and success of early large-scale crowd sourcing activities is made possible through leveraging Web 2.0 technologies that allow for mass participation from distributed individuals. The Earthquake Engineering Research Institute (EERI) in Oakland, California recently participated in two crowd sourcing projects. One was initiated and coordinated by EERI, while in the second case EERI was invited to contribute once the crowd sourcing activity was underway. In both projects there was: 1) the determination of a problem or set of tasks that could benefit immediately from the engagement of an informed volunteer group of professionals; 2) a segmenting of the problem into discrete pieces that could be completed in a short period of time (from ten minutes to four hours); 3) a call to action, where an interested community was made aware of the project; and 4) the collection, aggregation, vetting and ultimately distribution of the results in a relatively short period of time. The first EERI crowd sourcing example was the use of practicing engineers and engineering students in California to help estimate the number of pre-1980 concrete buildings in the high seismic risk counties in the state. This building type is known to perform poorly in earthquakes, and state officials were interested in understanding

  17. Greenhouse Gas reduction for scenarios of power sources development of the Republic of Moldova

    Directory of Open Access Journals (Sweden)

    Comendant I.

    2010-04-01

    Full Text Available For the new power market conditions, Moldova power sources development options up to 2033 are evaluated, and for the six scenarios selected the greenhouse gas reduction impact is determined.

  18. Weight reduction of automobile parts using light metals. Keikinzoku shiyo ni yoru jidosha buhin no keiryoka

    Energy Technology Data Exchange (ETDEWEB)

    Hayashi, S [Toyota Motor Corp., Aichi (Japan)

    1992-12-25

    Weight reduction of automobiles is required from the viewpoint of reduction of CO2 emission and energy conservation. Comparing a car with another one of almost the same size and performance with 1% reduced weight, combustion efficiency of the latter can be improved by 0.5-0.8%. This report introduces several examples, in which steel parts are replaced with light alloy parts to reduce car weight, and describes the future perspective. Concerning a cylinder block which is the heaviest part among engine parts, a block made of aluminum alloy with no cast liner has been developed. There is also an example of an oil pan adopting aluminum die-cast for a part of it. A valve lifter made of aluminum alloy has been developed for valve system parts and has contributed to friction loss, noise reduction, and improvement of fuel consumption. As for steering system parts, a steering bracket made of Mg alloy die-cast has been developed. The use of light alloy parts, in general, increases material cost. Therefore it is now required to build up closer connection between designs and production techniques and to improve reliability of casting and forging technologies. 5 refs., 20 figs.

  19. Spent catalyst waste management. A review. Part 1. Developments in hydroprocessing catalyst waste reduction and use

    Energy Technology Data Exchange (ETDEWEB)

    Marafi, M.; Stanislaus, A. [Petroleum Refining Department, Petroleum Research and Studies Center, Kuwait Institute for Scientific Research, P.O. Box 24885, 13109-Safat (Kuwait)

    2008-04-15

    Solid catalysts containing metals, metal oxides or sulfides, which play a key role in the refining of petroleum to clean fuels and many other valuable products, become solid wastes after use. In many refineries, the spent catalysts discarded from hydroprocessing units form a major part of these solid wastes. Disposal of spent hydroprocessing catalysts requires compliance with stringent environmental regulations because of their hazardous nature and toxic chemicals content. Various options such as minimizing spent catalyst waste generation by regeneration and reuse, metals recovery, utilization to produce useful materials and treatment for safe disposal, could be considered to deal with the spent catalyst environmental problem. In this paper, information available in the literature on spent hydroprocessing catalyst waste reduction at source by using improved more active and more stable catalysts, regeneration, rejuvenation and reuse of deactivated catalysts in many cycles, and reusing in other processes are reviewed in detail with focus on recent developments. Available methods for recycling of spent hydroprocessing catalysts by using them as raw materials for the preparation of active new catalysts and many other valuable products are also reviewed. (author)

  20. Reduction of Radioactive Waste Through the Reuse and Recycle Policy of the Sealed Radioactive Sources Management

    OpenAIRE

    Marpaung, T

    2012-01-01

    In the past few years, the utilization of sealed source for medical, industrial and research purposes has shown an accelerating increase. This situation will lead to increases in the amount of sealed radioactive. During its use, a sealed radioactive waste will eventually become either a spent sealed source or disused sealed radioactive source (DSRS), due to certain factors. The reduction of the amount of radioactive waste can be executed through the application of reuse and recycle of sealed ...

  1. Fully probabilistic seismic source inversion – Part 1: Efficient parameterisation

    Directory of Open Access Journals (Sweden)

    S. C. Stähler

    2014-11-01

    Full Text Available Seismic source inversion is a non-linear problem in seismology where not just the earthquake parameters themselves but also estimates of their uncertainties are of great practical importance. Probabilistic source inversion (Bayesian inference is very adapted to this challenge, provided that the parameter space can be chosen small enough to make Bayesian sampling computationally feasible. We propose a framework for PRobabilistic Inference of Seismic source Mechanisms (PRISM that parameterises and samples earthquake depth, moment tensor, and source time function efficiently by using information from previous non-Bayesian inversions. The source time function is expressed as a weighted sum of a small number of empirical orthogonal functions, which were derived from a catalogue of >1000 source time functions (STFs by a principal component analysis. We use a likelihood model based on the cross-correlation misfit between observed and predicted waveforms. The resulting ensemble of solutions provides full uncertainty and covariance information for the source parameters, and permits propagating these source uncertainties into travel time estimates used for seismic tomography. The computational effort is such that routine, global estimation of earthquake mechanisms and source time functions from teleseismic broadband waveforms is feasible.

  2. Source reduction for prevention of methylene chloride hazards: cases from four industrial sectors

    Directory of Open Access Journals (Sweden)

    Ellenbecker Michael J

    2003-07-01

    Full Text Available Abstract Background Source reduction, defined as chemical, equipment and process changes that intervene in an industrial process to eliminate or reduce hazards, has not figured as a front-line strategy for the protection of workers' health. Such initiatives are popular for environmental protection, but their feasibility and effectiveness as an industrial hygiene approach have not been well described. Methods We investigated four cases of source reduction as a hazard prevention strategy in Massachusetts companies that had used methylene chloride, an occupational carcinogen, for cleaning and adhesive thinning. Three cases were retrospective and one was prospective, where the researchers assisted with the source reduction process change. Data were collected using qualitative research methods, including in-depth interviews and site visits. Results Motivated by environmental restrictions, a new worker health standard, and opportunity for productivity improvements, three companies eliminated their use of methylene chloride by utilizing available technologies and drop-in substitutes. Aided by technical assistance from the investigators, a fourth case dramatically reduced its use of methylene chloride via process and chemistry changes. While the companies' evaluations of potential work environment impacts of substitutes were not extensive, and in two cases new potential hazards were introduced, the overall impact of the source reduction strategy was deemed beneficial, both from a worker health and a production standpoint. Conclusion The findings from these four cases suggest that source reduction should be considered potentially feasible and effective for reducing or eliminating the potential hazards of methylene chloride exposure. Especially when faced with a hazard that is both an environmental and worker health concern, companies may chose to change their processes rather than rely on local exhaust ventilation equipment or personal protective

  3. REDUCTION IN ASTHMA MORBIDITY IN CHILDREN AS A RESULT OF HOME REMEDIATION AIMED AT MOISTURE SOURCES

    Science.gov (United States)

    Objective: Home dampness, presence of mold and allergens have been associated with asthma morbidity. We examined changes in asthma morbidity in children as a result of home remediation aimed at moisture sources.Design: Prospective, randomized controlled trial.Part...

  4. Using mobile source emission reductions to offset stationary surce rule requirements

    International Nuclear Information System (INIS)

    Nazemi, M.A.; Beruldsen, K.J.

    1993-01-01

    A number of mobile source strategies have been evaluated that could potentially be used as an alternative means of compliance with existing stationary source regulations, at a lower cost. The evaluation was spurred by both public and private sector interest in identifying the lowest cost air pollution reduction strategies, and the realization that mobile sources are the predominate contributor to the air pollution problem in the South Coast Air Quality Basin. Strategies evaluated included removing older vehicles from the in-use population, use of alternative fuels, inspection and maintenance measures, application of remote sensing technology, exceeding AVR requirements, as well as a number of other strategies. Key implementation issues have been identified, so that the viability of each mobile source strategies could be assessed. These issues include: (1) quantification of emissions benefits, (2) determining whether the mobile source strategy would generate emission reductions surplus to existing and planned mobile source regulations, and (3) assessing the potential for enforceability. The results of evaluation indicate that there are a number of promising mobile source emission strategies that could provide quantifiable, surplus, and enforceable emission reductions

  5. Analysis of inconsistent source sampling in monte carlo weight-window variance reduction methods

    Directory of Open Access Journals (Sweden)

    David P. Griesheimer

    2017-09-01

    Full Text Available The application of Monte Carlo (MC to large-scale fixed-source problems has recently become possible with new hybrid methods that automate generation of parameters for variance reduction techniques. Two common variance reduction techniques, weight windows and source biasing, have been automated and popularized by the consistent adjoint-driven importance sampling (CADIS method. This method uses the adjoint solution from an inexpensive deterministic calculation to define a consistent set of weight windows and source particles for a subsequent MC calculation. One of the motivations for source consistency is to avoid the splitting or rouletting of particles at birth, which requires computational resources. However, it is not always possible or desirable to implement such consistency, which results in inconsistent source biasing. This paper develops an original framework that mathematically expresses the coupling of the weight window and source biasing techniques, allowing the authors to explore the impact of inconsistent source sampling on the variance of MC results. A numerical experiment supports this new framework and suggests that certain classes of problems may be relatively insensitive to inconsistent source sampling schemes with moderate levels of splitting and rouletting.

  6. Global threat reduction initiative efforts to address transportation challenges associated with the recovery of disused radioactive sealed sources - 10460

    International Nuclear Information System (INIS)

    Whitworth, Julie; Abeyta, Cristy L.; Griffin, Justin M.; Matzke, James L.; Pearson, Michael W.; Cuthbertson, Abigail; Rawl, Richard; Singley, Paul

    2010-01-01

    Proper disposition of disused radioactive sources is essential for their safe and secure management and necessary to preclude their use in malicious activities. Without affordable, timely transportation options, disused sealed sources remain in storage at hundreds of sites throughout the country and around the world. While secure storage is a temporary measure, the longer sources remain disused or unwanted the chances increase that they will become unsecured or abandoned. The Global Threat Reduction Initiative's Off-Site Source Recovery Project (GTRIlOSRP), recovers thousands of disused and unwanted sealed sources annually as part of GTRl's larger mission to reduce and protect high risk nuclear and radiological materials located at civilian sites worldwide. Faced with decreasing availability of certified transportation containers to support movement of disused and unwanted neutron- and beta/gamma-emitting radioactive sealed sources, GTRIlOSRP has initiated actions to ensure the continued success of the project in timely recovery and management of sealed radioactive sources. Efforts described in this paper to enhance transportation capabilities include: (sm b ullet) Addition of authorized content to existing and planned Type B containers to support the movement of non-special form and other Type B-quantity sealed sources; (sm b ullet) Procurement of vendor services for the design, development, testing and certification of a new Type B container to support transportation of irradiators, teletherapy heads or sources removed from these devices using remote handling capabilities such as the IAEA portable hot cell facility; (sm b ullet) Expansion of shielded Type A container inventory for transportation of gamma-emitting sources in activity ranges requiring use of shielding for conformity with transportation requirements; (sm b ullet) Approval of the S300 Type A fissile container for transport of Pu-239 sealed sources internationally; (sm b ullet) Technology transfer of

  7. Health effects and sources of indoor air pollution. Part I

    International Nuclear Information System (INIS)

    Samet, J.M.; Marbury, M.C.; Spengler, J.D.

    1987-01-01

    Since the early 1970s, the health effects of indoor air pollution have been investigated with increasing intensity. Consequently, a large body of literature is now available on diverse aspects of indoor air pollution: sources, concentrations, health effects, engineering, and policy. This review begins with a review of the principal pollutants found in indoor environments and their sources. Subsequently, exposure to indoor air pollutants and health effects are considered, with an emphasis on those indoor air quality problems of greatest concern at present: passive exposure to tobacco smoke, nitrogen dioxide from gas-fueled cooking stoves, formaldehyde exposure, radon daughter exposure, and the diverse health problems encountered by workers in newer sealed office buildings. The review concludes by briefly addressing assessment of indoor air quality, control technology, research needs, and clinical implications. 243 references

  8. Flux and Mass Reduction Resulting from ZVIClay Remediation of a PCE DNAPL Source Zone

    DEFF Research Database (Denmark)

    Fjordbøge, Annika Sidelmann; Kjeldsen, Peter; Riis, C.

    2010-01-01

    of bentonite clay. The degradation of PCE in the treated source area and the development in the downstream flux of chlorinated compounds have been monitored in six sampling campaigns. A PCE half-life of 50 days and a reduction of the average concentration of PCE of more than 99% were found during the first...

  9. Modeling the effects of integrating larval habitat source reduction and insecticide treated nets for malaria control.

    Directory of Open Access Journals (Sweden)

    Laith Yakob

    Full Text Available Integrated vector management for malaria control has received a lot of recent interest. Attacking multiple points in the transmission cycle is hoped to act synergistically and improve upon current single-tool interventions based on the use of insecticide-treated bed nets (ITNs. In the present study, we theoretically examined the application of larval habitat source reduction with ITNs in reducing malaria transmission. We selected this type of environmental management to complement ITNs because of a potential secondary mode of action that both control strategies share. In addition to increasing vector mortality, ITNs reduce the rate at which female mosquitoes locate human hosts for blood feeding, thereby extending their gonotrophic cycle. Similarly, while reducing adult vector emergence and abundance, source reduction of larval habitats may prolong the cycle duration by extending delays in locating oviposition sites. We found, however, that source reduction of larval habitats only operates through this secondary mode of action when habitat density is below a critical threshold. Hence, we illustrate how this strategy becomes increasingly effective when larval habitats are limited. We also demonstrate that habitat source reduction is better suited to human populations of higher density and in the presence of insecticide resistance or when the insecticidal properties of ITNs are depleted.

  10. Implementation of VOC source reduction practices in a manufactured house and in school classrooms

    International Nuclear Information System (INIS)

    Hodgson, A.T.; Apte, M.G.; Shendell, D.G.; Beal, D.; McIlvaine, J.E.R.

    2002-01-01

    Detailed studies of a new manufactured house and four new industrialized relocatable school classrooms were conducted to determine the emission sources of formaldehyde and other VOCs and to identify and implement source reduction practices. Procedures were developed to generate VOC emission factors that allowed reasonably accurate predictions of indoor air VOC concentrations. Based on the identified sources of formaldehyde and other aldehydes, practices were developed to reduce the concentrations of these compounds in new house construction. An alternate ceiling panel reduced formaldehyde concentrations in the classrooms. Overall, the classrooms had relatively low VOC concentrations

  11. Reduction of Radioactive Waste Through the Reuse and Recycle Policy of the Sealed Radioactive Sources Management

    Directory of Open Access Journals (Sweden)

    T. Marpaung

    2012-08-01

    Full Text Available In the past few years, the utilization of sealed source for medical, industrial and research purposes has shown an accelerating increase. This situation will lead to increases in the amount of sealed radioactive. During its use, a sealed radioactive waste will eventually become either a spent sealed source or disused sealed radioactive source (DSRS, due to certain factors. The reduction of the amount of radioactive waste can be executed through the application of reuse and recycle of sealed source. The reuse and recycle policy for spent and disused sealed sources are not already specified yet. The reuse of spent sealed sources can be applied only for the sources which had been used in the medical field for radiotherapy, namely the reuse of a teletherapy Co-60 source in a calibration facility. The recycle of a spent sealed source can be performed for radioactive sources with relatively high activities and long half-lives; however, the recycling activity may only be performed by the manufacturer. To avoid legal conflicts, in the amendment to the Government Regulation No.27 Year 2002 on Management of Radioactive Waste, there will be a recommendation for a new scheme in the management of radioactive waste to facilitate the application of the principles of reduce, reuse, and recycle

  12. Reduction of Radioactive Waste Through the Reuse and Recycle Policy of the Sealed Radioactive Sources Management

    International Nuclear Information System (INIS)

    Marpaung, T.

    2012-01-01

    In the past few years, the utilization of sealed source for medical, industrial and research purposes has shown an accelerating increase. This situation will lead to increases in the amount of sealed radioactive. During its use, a sealed radioactive waste will eventually become either a spent sealed source or disused sealed radioactive source (DSRS), due to certain factors. The reduction of the amount of radioactive waste can be executed through the application of reuse and recycle of sealed source. The reuse and recycle policy for spent and disused sealed sources are not already specified yet. The reuse of spent sealed sources can be applied only for the sources which had been used in the medical field for radiotherapy, namely the reuse of a teletherapy Co-60 source in a calibration facility. The recycle of a spent sealed source can be performed for radioactive sources with relatively high activities and long half-lives; however, the recycling activity may only be performed by the manufacturer. To avoid legal conflicts, in the amendment to the Government Regulation No.27 Year 2002 on Management of Radioactive Waste, there will be a recommendation for a new scheme in the management of radioactive waste to facilitate the application of the principles of reduce, reuse, and recycle (author)

  13. Reducing plant radiation fields by source term reduction - tracking cobalt and antimony to their sources at Gentilly-2

    International Nuclear Information System (INIS)

    Gauthier, P.; Guzonas, D.A.

    2006-01-01

    the same specifications at Gentilly-2 as at other CANDU 6 plants. Consequently, the task group revisited operating and maintenance practices, going back through station operating history to identify operational practices that could have lead to increased 59 Co release and/or 60 Co production. The focus rapidly moved to the fuel handling system, as it had long been suspected, but never proven, that the Stellite ram balls were a major source of 59 Co; the fuelling machines provide a direct route for the introduction of corrosion or wear products into the reactor core. Data on the gamma fields measured in the fuelling machine D 2 O supply room from 1995 to the present were reviewed. Water samples were taken and chemically analysed. The results confirmed the presence of 59 Co, probably generated by the wear and corrosion of the Stellite ram balls, and also confirmed the presence of antimony in the system. As part of the task group program, γ-spectrometry was performed in the course of a refuelling cycle. The results showed that variations in the general radiation fields observed in the fuelling machine D 2 O supply room resulted from variations of the 122 Sb and 124 Sb concentrations in the process water. The presence of 122 Sb (t 1/2 3.2 d) suggested that the antimony was recently released from the reactor core. 60 Co was also detected but the level was constant; 59 Co from the ram balls is invisible to γ-spectrometry before it is activated to 60 Co. Remedial actions were implemented in mid-July, 2004. Shortly after, a significant reduction in the radiation fields in the Gentilly-2 fuelling machine D2 O supply room was confirmed. During an unplanned outage in December 2004, a decrease in fields, in particular those due to 60 Co and radioantimony, was found at the reactor face. Activity monitoring scheduled for the 2005 annual outage should confirm if the source of the abnormally high fields has finally been identified. This presentation will describe the task force

  14. Research of noise emission sources in railway transport and effective ways of their reduction

    Directory of Open Access Journals (Sweden)

    Zvolenský Peter

    2017-01-01

    Full Text Available In the EU conditions attention is systematically paid to noise reduction on the railways. Because TSI rules systematically tighten limits for noise emissions from railway vehicles, noise research must be addressed by all Member States, as the main technical solutions for railway vehicles and construction technological aspects of railway operations can result in lower noise exposure of affected areas or objects. The paper focuses on theoretical investigation of sources and paths of sound propagation, possibilities of noise reduction both on vehicles and by infrastructure and experimental measurements of the situation in transport practice. Methodology for reducing railway noise around tracks has been presented, too.

  15. Reductions in mortality among Medicare beneficiaries following the implementation of Medicare Part D.

    Science.gov (United States)

    Semilla, April P; Chen, Fang; Dall, Timothy M

    2015-07-01

    Medicare Part D is a prescription drug program that provides seniors and disabled individuals enrolled in Medicare with outpatient drug coverage benefits. Part D has been shown to increase access to medicines and improve medication adherence; however, the effect of Part D on health outcomes has not yet been extensively studied. In this study, we used a published and validated Markov-based microsimulation model to quantify the relationships among medication use, disease incidence and severity, and mortality. Based on the simulation results, we estimate that since the implementation of Part D in 2006, nearly 200,000 Medicare beneficiaries have lived at least 1 year longer. Reductions in mortality have occurred because of fewer deaths associated with medication-sensitive conditions such as diabetes, congestive heart failure, stroke, and myocardial infarction. Improved access to medication through Medicare Part D helps patients improve blood pressure, cholesterol, and blood glucose levels, which in turn can prevent or delay the onset of disease and the incidence of adverse health events, thus reducing mortality.

  16. Reduction of the environmental concentration of air pollutants by proper geometrical orientation of industrial line sources

    International Nuclear Information System (INIS)

    Tadmor, J.

    1980-01-01

    An account is given of an Israeli study of two line sources, one composed of 10 and the other of 20 individual sources. The height of release ranged from 15.7 to 39.6 m, with a uniform rate of release of a gaseous pollutant of 1 Ci/s for each source. Average pollutant concentration was plotted as a function of the rotation angle of the line sources. Reduction of pollutant concentration by a particular rotation of the line sources attained values of up to 50%. At certain rotation angles of the line sources, the environmental concentration was lower even as compared with a single high source. Results also depended on atmospheric conditions. It is suggested that considering the increase in cost of augmenting the height of release as a means of reducing the air pollutant concentration, determination of the optimum geometric orientation of the line sources should be considered as an economical means of improving environmental air quality. (U.K.)

  17. Reduction of sources of error and simplification of the Carbon-14 urea breath test

    International Nuclear Information System (INIS)

    Bellon, M.S.

    1997-01-01

    Full text: Carbon-14 urea breath testing is established in the diagnosis of H. pylori infection. The aim of this study was to investigate possible further simplification and identification of error sources in the 14 C urea kit extensively used at the Royal Adelaide Hospital. Thirty six patients with validated H. pylon status were tested with breath samples taken at 10,15, and 20 min. Using the single sample value at 15 min, there was no change in the diagnostic category. Reduction or errors in analysis depends on attention to the following details: Stability of absorption solution, (now > 2 months), compatibility of scintillation cocktail/absorption solution. (with particular regard to photoluminescence and chemiluminescence), reduction in chemical quenching (moisture reduction), understanding counting hardware and relevance, and appropriate response to deviation in quality assurance. With this experience, we are confident of the performance and reliability of the RAPID-14 urea breath test kit now available commercially

  18. Reduction rules-based search algorithm for opportunistic replacement strategy of multiple life-limited parts

    Directory of Open Access Journals (Sweden)

    Xuyun FU

    2018-01-01

    Full Text Available The opportunistic replacement of multiple Life-Limited Parts (LLPs is a problem widely existing in industry. The replacement strategy of LLPs has a great impact on the total maintenance cost to a lot of equipment. This article focuses on finding a quick and effective algorithm for this problem. To improve the algorithm efficiency, six reduction rules are suggested from the perspectives of solution feasibility, determination of the replacement of LLPs, determination of the maintenance occasion and solution optimality. Based on these six reduction rules, a search algorithm is proposed. This search algorithm can identify one or several optimal solutions. A numerical experiment shows that these six reduction rules are effective, and the time consumed by the algorithm is less than 38 s if the total life of equipment is shorter than 55000 and the number of LLPs is less than 11. A specific case shows that the algorithm can obtain optimal solutions which are much better than the result of the traditional method in 10 s, and it can provide support for determining to-be-replaced LLPs when determining the maintenance workscope of an aircraft engine. Therefore, the algorithm is applicable to engineering applications concerning opportunistic replacement of multiple LLPs in aircraft engines.

  19. Getting to the Source: a Survey of Quantitative Data Sources Available to the Everyday Librarian: Part II: Data Sources from Specific Library Applications

    Directory of Open Access Journals (Sweden)

    Lisa Goddard

    2007-03-01

    Full Text Available This is the second part of a two-part article that provides a survey of data sources which are likely to be immediately available to the typical practitioner who wishes to engage in statistical analysis of collections and services within his or her own library. Part I outlines the data elements which can be extracted from web server logs, and discusses web log analysis tools. Part II looks at logs, reports, and data sources from proxy servers, resource vendors, link resolvers, federated search engines, institutional repositories, electronic reference services, and the integrated library system.

  20. The potentional of renewable energy sources for greenhouse gases emissions reduction in Macedonia

    Directory of Open Access Journals (Sweden)

    Dedinec Aleksandar

    2012-01-01

    Full Text Available As European Union (EU candidate country, Macedonia is in the process of adoption of the EU strategic energy policies, harmonization of the national legislation with the EU legislation and defining the respective national goals. In this regard, the government has recently adopted a National Strategy for Utilization of Renewable Energy Sources (RES, prepared by ICEIM-MANU. The main goal of this paper is to assess the potential for greenhouse gases (GHG emissions reduction by implementation of 21%-RES-scenarios from the Strategy. The corresponding emissions reduction is calculated against the baseline (reference scenario developed within the Second National Communication on Climate Change. Furthermore, all potential RES technologies are analyzed from economic aspect and combined in a form of emissions reduction cost curve, displaying the total marginal cost of the GHG emissions reduction by RES. Finally, on the bases of the environmental and economic effectiveness of the considered RES technologies, as well as taking into account the country specific barriers, the priority actions for GHG emissions reduction are identified.

  1. VOC reduction technology deveolpment as part of the U.S. Department of Energy, Industrial Waste Reduction Program

    International Nuclear Information System (INIS)

    Cranford, B.

    1993-01-01

    A strong industry is vital to U.S. Economic health and prosperity, but U.S. industry is facing serious challenges both domestically and internationally. One of these challenges is the reduction of volatile organic compounds emissions from industrial processes and products. To assist industry with these challenges, the U.S. Department of Energy established the Industrial Waste Reduction Program to improve energy efficiency and competitiveness to private industry through cost-effective waste material reduction. This paper describes the programs and the use of joint partnerships between the Department of Energy, industry, national laboratories, universities and others, in developing technologies which reduce VOC emissions while improving energy efficiency. This paper also describes the process and selection criteria for participation in the program, and briefly describes the following five VOC reduction technologies under development: Dual Cure Coatings, Solvent Reduction through use of a No-clean Soldering Process, Solvent Waste Minimization by Supercritical CO 2 Cleaning Process, ethanol Recovery Process, and Membrane Vapor Recovery Systems. The VOC reductions as well as the energy savings and other benefits to the U.S. are discussed

  2. Prediction With Dimension Reduction of Multiple Molecular Data Sources for Patient Survival

    Directory of Open Access Journals (Sweden)

    Adam Kaplan

    2017-07-01

    Full Text Available Predictive modeling from high-dimensional genomic data is often preceded by a dimension reduction step, such as principal component analysis (PCA. However, the application of PCA is not straightforward for multisource data, wherein multiple sources of ‘omics data measure different but related biological components. In this article, we use recent advances in the dimension reduction of multisource data for predictive modeling. In particular, we apply exploratory results from Joint and Individual Variation Explained (JIVE, an extension of PCA for multisource data, for prediction of differing response types. We conduct illustrative simulations to illustrate the practical advantages and interpretability of our approach. As an application example, we consider predicting survival for patients with glioblastoma multiforme from 3 data sources measuring messenger RNA expression, microRNA expression, and DNA methylation. We also introduce a method to estimate JIVE scores for new samples that were not used in the initial dimension reduction and study its theoretical properties; this method is implemented in the R package R.JIVE on CRAN, in the function jive.predict.

  3. Behaviour of the RBMK-1000 plant during reactivity disturbances under part load reduction - completing investigations

    International Nuclear Information System (INIS)

    Clemente, M.; Langenbuch, S.

    1989-01-01

    This report describes investigations of the behavior of a RBMK-1000 reactor core during reactivity initiated accidents and completes earlier studies of the Chernobyl accident. Special questions related to this accident are studied, e.g. the effect of Xenon dynamics during the delayed load reduction and the coarse of the experiment as planned with the coast-down of four main recirculaton pumps at nominal part load conditions. The main interest is the detailed analysis of reactivity initiated accidents in the low power range till 25% during start-up. In the calculations no reactor trip is taken into account. The results confirm the unfavourable effects of the positive void coefficient, which are amplified in the low power range. Finally the results are discussed in comparison to other positive reactivity effects. (orig.) [de

  4. Surface Coating of Plastic Parts for Business Machines (Industrial Surface Coating): New Source Performance Standards (NSPS)

    Science.gov (United States)

    Learn more about the new source performance standards (NSPS) for surface coating of plastic parts for business machines by reading the rule summary and history and finding the code of federal regulations as well as related rules.

  5. Kinetics of sodium borohydride direct oxidation and oxygen reduction in sodium hydroxide electrolyte - Part II. O-2 reduction

    Czech Academy of Sciences Publication Activity Database

    Chatenet, M.; Micoud, F.; Roche, I.; Chainet, E.; Vondrák, Jiří

    2006-01-01

    Roč. 51, č. 25 (2006), s. 5452-5458 ISSN 0013-4686 Institutional research plan: CEZ:AV0Z40320502 Keywords : oxygen reduction reaction selectivity * platinum * silver Subject RIV: CA - Inorganic Chemistry Impact factor: 2.955, year: 2006

  6. The investigation of the FM heavy forging process by the Moiré method. Part II: Consecutive reduction results

    NARCIS (Netherlands)

    Wang, S.L.; Cao, Q.X.

    1994-01-01

    In part I of this work (preceding paper), single-reduction results on the FM forging process were reported. In the work reported in this paper, the cavity closing laws of the consecutive reduction process were investigated, the appropriate turn-over and feed procedure being obtained, along with the

  7. 16 CFR Table 4 to Part 1512 - Relative Energy Distribution of Sources

    Science.gov (United States)

    2010-01-01

    ... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Relative Energy Distribution of Sources 4... SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR BICYCLES Pt. 1512, Table 4 Table 4 to Part 1512—Relative Energy Distribution of Sources Wave length (nanometers) Relative energy 380 9.79 390 12.09 400 14.71 410 17.68 420 21...

  8. pH control for enhanced reductive bioremediation of chlorinated solvent source zones

    International Nuclear Information System (INIS)

    Robinson, Clare; Barry, D.A.; McCarty, Perry L.; Gerhard, Jason I.; Kouznetsova, Irina

    2009-01-01

    Enhanced reductive dehalogenation is an attractive treatment technology for in situ remediation of chlorinated solvent DNAPL source areas. Reductive dehalogenation is an acid-forming process with hydrochloric acid and also organic acids from fermentation of the electron donors typically building up in the source zone during remediation. This can lead to groundwater acidification thereby inhibiting the activity of dehalogenating microorganisms. Where the soils' natural buffering capacity is likely to be exceeded, the addition of an external source of alkalinity is needed to ensure sustained dehalogenation. To assist in the design of bioremediation systems, an abiotic geochemical model was developed to provide insight into the processes influencing the groundwater acidity as dehalogenation proceeds, and to predict the amount of bicarbonate required to maintain the pH at a suitable level for dehalogenating bacteria (i.e., > 6.5). The model accounts for the amount of chlorinated solvent degraded, site water chemistry, electron donor, alternative terminal electron-accepting processes, gas release and soil mineralogy. While calcite and iron oxides were shown to be the key minerals influencing the soil's buffering capacity, for the extensive dehalogenation likely to occur in a DNAPL source zone, significant bicarbonate addition may be necessary even in soils that are naturally well buffered. Results indicated that the bicarbonate requirement strongly depends on the electron donor used and availability of competing electron acceptors (e.g., sulfate, iron (III)). Based on understanding gained from this model, a simplified model was developed for calculating a preliminary design estimate of the bicarbonate addition required to control the pH for user-specified operating conditions.

  9. pH control for enhanced reductive bioremediation of chlorinated solvent source zones

    Energy Technology Data Exchange (ETDEWEB)

    Robinson, Clare, E-mail: clare.robinson@epfl.ch [Laboratoire de technologie ecologique, Institut d' ingenierie de l' environnement, Station No. 2, Ecole Polytechnique Federale de Lausanne, CH-1015 Lausanne (Switzerland); Now at: Department of Civil and Environmental Engineering, University of Western Ontario, London, Canada N6A 5B9 (Canada); Barry, D.A., E-mail: andrew.barry@epfl.ch [Laboratoire de technologie ecologique, Institut d' ingenierie de l' environnement, Station No. 2, Ecole Polytechnique Federale de Lausanne, CH-1015 Lausanne (Switzerland); McCarty, Perry L., E-mail: pmccarty@stanford.edu [Department of Civil and Environmental Engineering, Stanford University, Stanford, CA 94305-4020 (United States); Gerhard, Jason I., E-mail: j.gerhard@ed.ac.uk [Now at: Department of Civil and Environmental Engineering, University of Western Ontario, London, Canada N6A 5B9 (Canada); Institute for Infrastructure and Environment, University of Edinburgh, Edinburgh, EH9 3JL (United Kingdom); Kouznetsova, Irina, E-mail: irina.kouznetsova@ed.ac.uk [Institute for Infrastructure and Environment, University of Edinburgh, Edinburgh, EH9 3JL (United Kingdom)

    2009-08-01

    Enhanced reductive dehalogenation is an attractive treatment technology for in situ remediation of chlorinated solvent DNAPL source areas. Reductive dehalogenation is an acid-forming process with hydrochloric acid and also organic acids from fermentation of the electron donors typically building up in the source zone during remediation. This can lead to groundwater acidification thereby inhibiting the activity of dehalogenating microorganisms. Where the soils' natural buffering capacity is likely to be exceeded, the addition of an external source of alkalinity is needed to ensure sustained dehalogenation. To assist in the design of bioremediation systems, an abiotic geochemical model was developed to provide insight into the processes influencing the groundwater acidity as dehalogenation proceeds, and to predict the amount of bicarbonate required to maintain the pH at a suitable level for dehalogenating bacteria (i.e., > 6.5). The model accounts for the amount of chlorinated solvent degraded, site water chemistry, electron donor, alternative terminal electron-accepting processes, gas release and soil mineralogy. While calcite and iron oxides were shown to be the key minerals influencing the soil's buffering capacity, for the extensive dehalogenation likely to occur in a DNAPL source zone, significant bicarbonate addition may be necessary even in soils that are naturally well buffered. Results indicated that the bicarbonate requirement strongly depends on the electron donor used and availability of competing electron acceptors (e.g., sulfate, iron (III)). Based on understanding gained from this model, a simplified model was developed for calculating a preliminary design estimate of the bicarbonate addition required to control the pH for user-specified operating conditions.

  10. Fast space-varying convolution using matrix source coding with applications to camera stray light reduction.

    Science.gov (United States)

    Wei, Jianing; Bouman, Charles A; Allebach, Jan P

    2014-05-01

    Many imaging applications require the implementation of space-varying convolution for accurate restoration and reconstruction of images. Here, we use the term space-varying convolution to refer to linear operators whose impulse response has slow spatial variation. In addition, these space-varying convolution operators are often dense, so direct implementation of the convolution operator is typically computationally impractical. One such example is the problem of stray light reduction in digital cameras, which requires the implementation of a dense space-varying deconvolution operator. However, other inverse problems, such as iterative tomographic reconstruction, can also depend on the implementation of dense space-varying convolution. While space-invariant convolution can be efficiently implemented with the fast Fourier transform, this approach does not work for space-varying operators. So direct convolution is often the only option for implementing space-varying convolution. In this paper, we develop a general approach to the efficient implementation of space-varying convolution, and demonstrate its use in the application of stray light reduction. Our approach, which we call matrix source coding, is based on lossy source coding of the dense space-varying convolution matrix. Importantly, by coding the transformation matrix, we not only reduce the memory required to store it; we also dramatically reduce the computation required to implement matrix-vector products. Our algorithm is able to reduce computation by approximately factoring the dense space-varying convolution operator into a product of sparse transforms. Experimental results show that our method can dramatically reduce the computation required for stray light reduction while maintaining high accuracy.

  11. Endogenous NO3- in the root as a source of substrate for reduction in the light

    International Nuclear Information System (INIS)

    Rufty, T.W. Jr.; Volk, R.J.; MacKown, C.T.

    1987-01-01

    An experiment was conducted to investigate the reduction of endogenous NO 3 - , which had been taken up by plants in darkness, during the course of the subsequent light period. Vegetative, nonnodulated soybean plant (Glycine max [L.]. Merrill, Ransom) were exposed to 1.0 millimolar 15 NO 3 - for 12 hours in darkness and then returned to a solution containing 1.0 millimolar 14 NO 3 - for the 12 hours chase period in the light. Another set of plants was exposed to 15 NO 3 - during the light period to allow a direct comparison of contributions of substrate from the endogenous and exogenous sources. At the end of the 15 NO 3 - exposure in the dark, 70% of the absorbed 15 NO 3 - remained unreduced, and 83% of this unreduced NO 3 - was retained in roots. The pool of endogenous 15 NO 3 - in roots was depleted at a steady rate during the initial 9 hours of light and was utilized almost exclusively in the formation of insoluble reduced-N in leaves. Unlabeled endogenous NO 3 - , which had accumulated in the root prior to the previous dark period, also was depleted in the light. When exogenous 15 NO 3 - was supplied during the light period, the rate of assimilation progressively increased, reflecting an increased rate of uptake and decreased accumulation of NO 3 - in the root tissue. The dark-absorbed endogenous NO 3 - in the root was the primary source of substrate for whole-plant NO 3 - reduction in the first 6 hours of the light period, and exogenous NO 3 - was the primary source of substrate thereafter

  12. Reduction of gas flow into a hollow cathode ion source for a neutral beam injector

    International Nuclear Information System (INIS)

    Tanaka, S.; Akiba, M.; Arakawa, Y.; Horiike, H.; Sakuraba, J.

    1982-01-01

    Experimental studies have been made on the reduction of the gas flow rate into ion sources which utilize a hollow cathode. The electron emitter of the hollow cathode was a barium oxide impregnated porous tungsten tube. The hollow cathode was mounted to a circular or a rectangular bucket source and the following results were obtained. There was a tendency for the minimum gas flow rate for the stable source operation to decrease with increasing orifice diameter of the hollow cathode up to 10 mm. A molybdenum button with an appropriate diameter set in front of the orifice reduced the minimum gas flow rate to one half of that without button. An external magnetic field applied antiparallel to the field generated by the heater current stabilized the discharges and reduced the minimum gas flow rate to one half of that without field. Combination of the button and the antiparallel field reduced the minimum gas flow rate from the initial value (9.5 Torr 1/s) to 2.4 Torr 1/s. The reason for these effects was discussed on the basis of the theory for arc starvation

  13. Comparative study of beam losses and heat loads reduction methods in MITICA beam source

    Energy Technology Data Exchange (ETDEWEB)

    Sartori, E., E-mail: emanuele.sartori@igi.cnr.it; Agostinetti, P.; Dal Bello, S.; Marcuzzi, D.; Serianni, G.; Veltri, P. [Consorzio RFX, Euratom-ENEA association, C.so Stati Uniti 4, 35127 Padova (Italy); Sonato, P. [Consorzio RFX, Euratom-ENEA association, C.so Stati Uniti 4, 35127 Padova (Italy); Dipartimento di Ingegneria Elettrica, Padova University, Via Gradenigo 6/a, 35131 Padova (Italy)

    2014-02-15

    In negative ion electrostatic accelerators a considerable fraction of extracted ions is lost by collision processes causing efficiency loss and heat deposition over the components. Stripping is proportional to the local density of gas, which is steadily injected in the plasma source; its pumping from the extraction and acceleration stages is a key functionality for the prototype of the ITER Neutral Beam Injector, and it can be simulated with the 3D code AVOCADO. Different geometric solutions were tested aiming at the reduction of the gas density. The parameter space considered is limited by constraints given by optics, aiming, voltage holding, beam uniformity, and mechanical feasibility. The guidelines of the optimization process are presented together with the proposed solutions and the results of numerical simulations.

  14. Alaska earthquake source for the SAFRR tsunami scenario: Chapter B in The SAFRR (Science Application for Risk Reduction) Tsunami Scenario

    Science.gov (United States)

    Kirby, Stephen; Scholl, David; von Huene, Roland E.; Wells, Ray

    2013-01-01

    Tsunami modeling has shown that tsunami sources located along the Alaska Peninsula segment of the Aleutian-Alaska subduction zone have the greatest impacts on southern California shorelines by raising the highest tsunami waves for a given source seismic moment. The most probable sector for a Mw ~ 9 source within this subduction segment is between Kodiak Island and the Shumagin Islands in what we call the Semidi subduction sector; these bounds represent the southwestern limit of the 1964 Mw 9.2 Alaska earthquake rupture and the northeastern edge of the Shumagin sector that recent Global Positioning System (GPS) observations indicate is currently creeping. Geological and geophysical features in the Semidi sector that are thought to be relevant to the potential for large magnitude, long-rupture-runout interplate thrust earthquakes are remarkably similar to those in northeastern Japan, where the destructive Mw 9.1 tsunamigenic earthquake of 11 March 2011 occurred. In this report we propose and justify the selection of a tsunami source seaward of the Alaska Peninsula for use in the Tsunami Scenario that is part of the U.S. Geological Survey (USGS) Science Application for Risk Reduction (SAFRR) Project. This tsunami source should have the potential to raise damaging tsunami waves on the California coast, especially at the ports of Los Angeles and Long Beach. Accordingly, we have summarized and abstracted slip distribution from the source literature on the 2011 event, the best characterized for any subduction earthquake, and applied this synoptic slip distribution to the similar megathrust geometry of the Semidi sector. The resulting slip model has an average slip of 18.6 m and a moment magnitude of Mw = 9.1. The 2011 Tohoku earthquake was not anticipated, despite Japan having the best seismic and geodetic networks in the world and the best historical record in the world over the past 1,500 years. What was lacking was adequate paleogeologic data on prehistoric earthquakes

  15. An examination of source material requirements contained in 10 CFR Part 40

    International Nuclear Information System (INIS)

    Nussbaumer, D.; Smith, D.A.; Wiblin, C.

    1992-10-01

    This report identifies issues for consideration for rule-making to update the requirements for source material in 10 CFR Part 40 and examines options for resolving these issues. The contemplated rulemaking is intended to update 10 CFR Part 40 to reflect current radiation protection principles and regulatory practices. It is expected that such an update would make requirements for the control of source material more comparable to those pertaining to byproduct material contained in 10 CFR Part 30. The newer biological data and dose calculation methodology reflected in revised 10 CFR Part 20 will be used in analyses of potential regulatory amendments. This report presents historical background information and discussion on the various issues identified and makes preliminary recommendations concerning needed regulatory changes and approaches to rulemaking

  16. NO{sub 2} and CO nonattainment areas: a pragmatic approach to source reduction assessment

    Energy Technology Data Exchange (ETDEWEB)

    Cernuschi, S; Giugliano, M; Marzolo, F [D.I.I.A.R. - Politecnico di Milano, Milan (Italy). Environmental Section

    1996-12-31

    Many Italian large conurbations have CO and NO{sub 2} air quality standards exceeded and, consequently, require control enforcement plans to attain and maintain regulations not respected. In planning the interventions to be undertaken a fundamental issue is represented by the relationships between active emission sources and air quality, commonly described through mathematical models for evaluating the expected effects of the different reduction scenarios. This approach, relatively feasible for slightly or non reactive pollutants like CO, becomes not as easy to be applied for secondary pollutants, like NO{sub 2}, mainly for the complex photo chemical reaction systems involved in their atmospheric presence and the consequent modeling difficulties related either to the description of the system itself than to the detail in input data required. A practicable alternative in this framework relies in the utilization of statistical models for deriving, through the empirical description of the relationships between the parameters of interest, the reduction levels required for complying with the standards. Following an approach already applied with useful results to the same area, present work reports on the development and application to Milan urban area of statistical models for describing the relationships between CO and NO{sub x} annual concentration averages and the corresponding air quality standard parameters (number of standard exceedances for CO and 98th percentile of hourly concentrations for NO{sub 2}). The models are utilised upstream to simple roll-back models for the assessment of the reduction in emissions strength required for attaining air quality standards for the area. (author)

  17. NO{sub 2} and CO nonattainment areas: a pragmatic approach to source reduction assessment

    Energy Technology Data Exchange (ETDEWEB)

    Cernuschi, S.; Giugliano, M.; Marzolo, F. [D.I.I.A.R. - Politecnico di Milano, Milan (Italy). Environmental Section

    1995-12-31

    Many Italian large conurbations have CO and NO{sub 2} air quality standards exceeded and, consequently, require control enforcement plans to attain and maintain regulations not respected. In planning the interventions to be undertaken a fundamental issue is represented by the relationships between active emission sources and air quality, commonly described through mathematical models for evaluating the expected effects of the different reduction scenarios. This approach, relatively feasible for slightly or non reactive pollutants like CO, becomes not as easy to be applied for secondary pollutants, like NO{sub 2}, mainly for the complex photo chemical reaction systems involved in their atmospheric presence and the consequent modeling difficulties related either to the description of the system itself than to the detail in input data required. A practicable alternative in this framework relies in the utilization of statistical models for deriving, through the empirical description of the relationships between the parameters of interest, the reduction levels required for complying with the standards. Following an approach already applied with useful results to the same area, present work reports on the development and application to Milan urban area of statistical models for describing the relationships between CO and NO{sub x} annual concentration averages and the corresponding air quality standard parameters (number of standard exceedances for CO and 98th percentile of hourly concentrations for NO{sub 2}). The models are utilised upstream to simple roll-back models for the assessment of the reduction in emissions strength required for attaining air quality standards for the area. (author)

  18. Reduction of PM emissions from specific sources reflected on key components concentrations of ambient PM10

    Science.gov (United States)

    Minguillon, M. C.; Querol, X.; Monfort, E.; Alastuey, A.; Escrig, A.; Celades, I.; Miro, J. V.

    2009-04-01

    The relationship between specific particulate emission control and ambient levels of some PM10 components (Zn, As, Pb, Cs, Tl) was evaluated. To this end, the industrial area of Castellón (Eastern Spain) was selected, where around 40% of the EU glazed ceramic tiles and a high proportion of EU ceramic frits (middle product for the manufacture of ceramic glaze) are produced. The PM10 emissions from the ceramic processes were calculated over the period 2000 to 2007 taking into account the degree of implementation of corrective measures throughout the study period. Abatement systems (mainly bag filters) were implemented in the majority of the fusion kilns for frit manufacture in the area as a result of the application of the Directive 1996/61/CE, leading to a marked decrease in PM10 emissions. On the other hand, ambient PM10 sampling was carried out from April 2002 to July 2008 at three urban sites and one suburban site of the area and a complete chemical analysis was made for about 35 % of the collected samples, by means of different techniques (ICP-AES, ICP-MS, Ion Chromatography, selective electrode and elemental analyser). The series of chemical composition of PM10 allowed us to apply a source contribution model (Principal Component Analysis), followed by a multilinear regression analysis, so that PM10 sources were identified and their contribution to bulk ambient PM10 was quantified on a daily basis, as well as the contribution to bulk ambient concentrations of the identified key components (Zn, As, Pb, Cs, Tl). The contribution of the sources identified as the manufacture and use of ceramic glaze components, including the manufacture of ceramic frits, accounted for more than 65, 75, 58, 53, and 53% of ambient Zn, As, Pb, Cs and Tl levels, respectively (with the exception of Tl contribution at one of the sites). The important emission reductions of these sources during the study period had an impact on ambient key components levels, such that there was a high

  19. 14 CFR Appendix M to Part 25 - Fuel Tank System Flammability Reduction Means

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel Tank System Flammability Reduction... 25—Fuel Tank System Flammability Reduction Means M25.1Fuel tank flammability exposure requirements. (a) The Fleet Average Flammability Exposure of each fuel tank, as determined in accordance with...

  20. Sourcing strategies for services that become part of the buying company's value proposition

    NARCIS (Netherlands)

    Valk, van der W.; Weele, van A.J.; Jahns, C.; Hartmann, E.

    2009-01-01

    Organisations are increasingly buying services that become part of their value proposition to their customers. At the same time, business services traditionally are sourced and contracted for in a traditional way. We study the single case of buying cleaning services by a Train Maintenance Company

  1. Complete Mapping of Complex Disulfide Patterns with Closely-Spaced Cysteines by In-Source Reduction and Data-Dependent Mass Spectrometry

    DEFF Research Database (Denmark)

    Cramer, Christian N; Kelstrup, Christian D; Olsen, Jesper V

    2017-01-01

    bonds are present in complicated patterns. This includes the presence of disulfide bonds in nested patterns and closely spaced cysteines. Unambiguous mapping of such disulfide bonds typically requires advanced MS approaches. In this study, we exploited in-source reduction (ISR) of disulfide bonds during...... the electrospray ionization process to facilitate disulfide bond assignments. We successfully developed a LC-ISR-MS/MS methodology to use as an online and fully automated partial reduction procedure. Postcolumn partial reduction by ISR provided fast and easy identification of peptides involved in disulfide bonding......Mapping of disulfide bonds is an essential part of protein characterization to ensure correct cysteine pairings. For this, mass spectrometry (MS) is the most widely used technique due to fast and accurate characterization. However, MS-based disulfide mapping is challenged when multiple disulfide...

  2. 40 CFR Appendix B to Part 63 - Sources Defined for Early Reduction Provisions

    Science.gov (United States)

    2010-07-01

    ... compressor e. Each product accumulator vessel f. Each agitator g. Each pressure relief device h. Each open-ended valve or line i. Each sampling connection system j. Each instrumentation system k. Each pump, valve, or connector in heavy liquid service l. Each closed vent system and control device [57 FR 62002...

  3. Reduction of non-point source contaminants associated with road-deposited sediments by sweeping.

    Science.gov (United States)

    Kim, Do-Gun; Kang, Hee-Man; Ko, Seok-Oh

    2017-09-19

    Road-deposited sediments (RDS) on an expressway, residual RDS collected after sweeping, and RDS removed by means of sweeping were analyzed to evaluate the degree to which sweeping removed various non-point source contaminants. The total RDS load was 393.1 ± 80.3 kg/km and the RDS, residual RDS, and swept RDS were all highly polluted with organics, nutrients, and metals. Among the metals studied, Cu, Zn, Pb, Ni, Ca, and Fe were significantly enriched, and most of the contaminants were associated with particles within the size range from 63 μm to 2 mm. Sweeping reduced RDS and its associated contaminants by 33.3-49.1% on average. We also measured the biological oxygen demand (BOD) of RDS in the present work, representing to our knowledge the first time that this has been done; we found that RDS contains a significant amount of biodegradable organics and that the reduction of BOD by sweeping was higher than that of other contaminants. Significant correlations were found between the contaminants measured, indicating that the organics and the metals originated from both exhaust and non-exhaust particles. Meanwhile, the concentrations of Cu and Ni were higher in 63 μm-2 mm particles than in smaller particles, suggesting that some metals in RDS likely exist intrinsically in particles, rather than only as adsorbates on particle surfaces. Overall, the results in this study showed that sweeping to collect RDS can be a good alternative for reduction of contaminants in runoff.

  4. The effect of multimicrophone noise reduction systems on sound source localization by users of binaural hearing aids.

    Science.gov (United States)

    Van den Bogaert, Tim; Doclo, Simon; Wouters, Jan; Moonen, Marc

    2008-07-01

    This paper evaluates the influence of three multimicrophone noise reduction algorithms on the ability to localize sound sources. Two recently developed noise reduction techniques for binaural hearing aids were evaluated, namely, the binaural multichannel Wiener filter (MWF) and the binaural multichannel Wiener filter with partial noise estimate (MWF-N), together with a dual-monaural adaptive directional microphone (ADM), which is a widely used noise reduction approach in commercial hearing aids. The influence of the different algorithms on perceived sound source localization and their noise reduction performance was evaluated. It is shown that noise reduction algorithms can have a large influence on localization and that (a) the ADM only preserves localization in the forward direction over azimuths where limited or no noise reduction is obtained; (b) the MWF preserves localization of the target speech component but may distort localization of the noise component. The latter is dependent on signal-to-noise ratio and masking effects; (c) the MWF-N enables correct localization of both the speech and the noise components; (d) the statistical Wiener filter approach introduces a better combination of sound source localization and noise reduction performance than the ADM approach.

  5. Strategic GHG reduction through the use of ground source heat pump technology

    International Nuclear Information System (INIS)

    Hanova, J; Dowlatabadi, H

    2007-01-01

    Higher energy prices and concern about climate change is drawing increasing attention to ground source heat pump (GSHP) systems. Their clear advantage lies in being able to provide heating using 25 to 30% of the energy consumed by even the most efficient conventional alternatives. Their drawback has been high capital costs and uncertainty about whether the emissions associated with the electric power used to energise the system has higher system-wide emissions than the highest-efficiency furnaces. This study delineates circumstances under which GSHP systems achieve net emission reductions, for different electricity generation methods, heat pump efficiencies, and heating loads. We illustrate the effect of relative fuel prices on annual operating savings using fuel prices in multiple countries. Annual operating savings determine how rapidly the technology achieves payback and then generates return on the initial capital investment. Finally, we highlight the least cost supply curve for using GSHP to reduce greenhouse gas emissions. Using the United States as a base reference case, this study explores the potential of GSHP in cold-climate countries worldwide

  6. Health risk reduction programs in employer-sponsored health plans: Part II-law and ethics.

    Science.gov (United States)

    Rothstein, Mark A; Harrell, Heather L

    2009-08-01

    We sought to examine the legal and ethical implications of workplace health risk reduction programs (HRRPs) using health risk assessments, individually focused risk reduction, and financial incentives to promote compliance. We conducted a literature review, analyzed relevant statutes and regulations, and considered the effects of these programs on employee health privacy. A variety of laws regulate HRRPs, and there is little evidence that employer-sponsored HRRPs violate these provisions; infringement on individual health privacy is more difficult to assess. Although current laws permit a wide range of employer health promotion activities, HRRPs also may entail largely unquantifiable costs to employee privacy and related interests.

  7. Health Risk Reduction Programs in Employer-Sponsored Health Plans: Part II—Law and Ethics

    Science.gov (United States)

    Rothstein, Mark A.; Harrell, Heather L.

    2011-01-01

    Objective We sought to examine the legal and ethical implications of workplace health risk reduction programs (HRRPs) using health risk assessments, individually focused risk reduction, and financial incentives to promote compliance. Methods We conducted a literature review, analyzed relevant statutes and regulations, and considered the effects of these programs on employee health privacy. Results A variety of laws regulate HRRPs, and there is little evidence that employer-sponsored HRRPs violate these provisions; infringement on individual health privacy is more difficult to assess. Conclusion Although current laws permit a wide range of employer health promotion activities, HRRPs also may entail largely unquantifiable costs to employee privacy and related interests. PMID:19625971

  8. Strategic positioning. Part 1: The sources of value under managed care.

    Science.gov (United States)

    Kauer, R T; Berkowitz, E

    1997-01-01

    Part 1 of this series organizes and discusses the sources of value against a background of an evolving managed care market. Part 2 will present, in more detail, the marketing and financial challenges to organizational positioning and performance across the four stages of managed care. What are the basic principles or tenets of value and how do they apply to the health care industry? Why is strategic positioning so important to health care organizations struggling in a managed care environment and what are the sources of value? Service motivated employees and the systems that educate them represent a stronger competitive advantage than having assets and technology that are available to anyone. As the health care marketplace evolves, organizations must develop a strategic position that will provide such value and for which the customer will be willing to pay.

  9. Market Analysis and Consumer Impacts Source Document. Part III. Consumer Behavior and Attitudes Toward Fuel Efficient Vehicles

    Science.gov (United States)

    1980-12-01

    This source document on motor vehicle market analysis and consumer impacts consists of three parts. Part III consists of studies and reviews on: consumer awareness of fuel efficiency issues; consumer acceptance of fuel efficient vehicles; car size ch...

  10. Radiological Threat Reduction (RTR) program: implementing physical security to protect large radioactive sources worldwide

    International Nuclear Information System (INIS)

    Lowe, Daniel L.

    2004-01-01

    The U.S. Department of Energy's Radiological Threat Reduction (RTR) Program strives to reduce the threat of a Radiological Dispersion Device (RDD) incident that could affect U.S. interests worldwide. Sandia National Laboratories supports the RTR program on many different levels. Sandia works directly with DOE to develop strategies, including the selection of countries to receive support and the identification of radioactive materials to be protected. Sandia also works with DOE in the development of guidelines and in training DOE project managers in physical protection principles. Other support to DOE includes performing rapid assessments and providing guidance for establishing foreign regulatory and knowledge infrastructure. Sandia works directly with foreign governments to establish cooperative agreements necessary to implement the RTR Program efforts to protect radioactive sources. Once necessary agreements are in place, Sandia works with in-country organizations to implement various security related initiatives, such as installing security systems and searching for (and securing) orphaned radioactive sources. The radioactive materials of interest to the RTR program include Cobalt 60, Cesium 137, Strontium 90, Iridium 192, Radium 226, Plutonium 238, Americium 241, Californium 252, and Others. Security systems are implemented using a standardized approach that provides consistency through out the RTR program efforts at Sandia. The approach incorporates a series of major tasks that overlap in order to provide continuity. The major task sequence is to: Establish in-country contacts - integrators, Obtain material characterizations, Perform site assessments and vulnerability assessments, Develop upgrade plans, Procure and install equipment, Conduct acceptance testing and performance testing, Develop procedures, and Conduct training. Other tasks are incorporated as appropriate and commonly include such as support of reconfiguring infrastructure, and developing security

  11. ZVI-Clay remediation of a chlorinated solvent source zone, Skuldelev, Denmark: 1. Site description and contaminant source mass reduction

    DEFF Research Database (Denmark)

    Fjordbøge, Annika Sidelmann; Riis, Charlotte; Christensen, Anders G.

    2012-01-01

    Field investigations on the effects of ZVI-Clay soil mixing were conducted at a small DNAPL source zone with PCE as the parent compound. In a one-year monitoring program, soil samples were collected at three horizontal sampling planes (2.5, 5.0 and 7.5m bgs.). PCE was found to have a pseudo first...

  12. Reduction of Surface Roughness by Means of Laser Processing over Additive Manufacturing Metal Parts.

    Science.gov (United States)

    Alfieri, Vittorio; Argenio, Paolo; Caiazzo, Fabrizia; Sergi, Vincenzo

    2016-12-31

    Optimization of processing parameters and exposure strategies is usually performed in additive manufacturing to set up the process; nevertheless, standards for roughness may not be evenly matched on a single complex part, since surface features depend on the building direction of the part. This paper aims to evaluate post processing treating via laser surface modification by means of scanning optics and beam wobbling to process metal parts resulting from selective laser melting of stainless steel in order to improve surface topography. The results are discussed in terms of roughness, geometry of the fusion zone in the cross-section, microstructural modification, and microhardness so as to assess the effects of laser post processing. The benefits of beam wobbling over linear scanning processing are shown, as heat effects in the base metal are proven to be lower.

  13. The Crowding-Out Effects of Garbage Fees and Voluntary Source Separation Programs on Waste Reduction: Evidence from China

    Directory of Open Access Journals (Sweden)

    Hongyun Han

    2016-07-01

    Full Text Available This paper examines how and to what degree government policies of garbage fees and voluntary source separation programs, with free indoor containers and garbage bags, can affect the effectiveness of municipal solid waste (MSW management, in the sense of achieving a desirable reduction of per capita MSW generation. Based on city-level panel data for years 1998–2012 in China, our empirical analysis indicates that per capita MSW generated is increasing with per capita disposable income, average household size, education levels of households, and the lagged per capita MSW. While both garbage fees and source separation programs have separately led to reductions in per capita waste generation, the interaction of the two policies has resulted in an increase in per capita waste generation due to the following crowding-out effects: Firstly, the positive effect of income dominates the negative effect of the garbage fee. Secondly, there are crowding-out effects of mandatory charging system and the subsidized voluntary source separation on per capita MSW generation. Thirdly, small subsidies and tax punishments have reduced the intrinsic motivation for voluntary source separation of MSW. Thus, compatible fee charging system, higher levels of subsidies, and well-designed public information and education campaigns are required to promote household waste source separation and reduction.

  14. Quenching of excited uranyl ion during its photochemical reduction by triphenylphosphine: Part III

    International Nuclear Information System (INIS)

    Sidhu, M.S.; Chahal, P.; Singh, R.J.

    1993-01-01

    Relative rates of bimolecular quenching of excited uranyl ion by some mono and di-substituted benzene derivatives have been measured during its photochemical reduction with triphenylphosphine. For the related compounds in a series it has been found that substituent groups enriching the aromatic π-electron cloud due to resonance stabilization, show an enhanced photophysical quenching action. The substituents decreasing the π-electron cloud and delocalization of positive charger over the benzene ring decrease the quenching action. (author). 16 refs., 2 figs., 1 tab

  15. Flood risk reduction and flow buffering as ecosystem services - Part 2

    NARCIS (Netherlands)

    Noordwijk, Van Meine; Tanika, Lisa; Lusiana, Betha

    2017-01-01

    Watersheds buffer the temporal pattern of river flow relative to the temporal pattern of rainfall. This "ecosystem service" is inherent to geology and climate, but buffering also responds to human use and misuse of the landscape. Buffering can be part of management feedback loops if salient,

  16. The Dutch minimum wage: a radical reduction shifts the main focus to part-time jobs

    NARCIS (Netherlands)

    Salverda, W.

    2009-01-01

    The paper is part of a broader international project undertaken by the ILO and the European Commission. It studies the Dutch minimum wage from the perspective of country differences in minimum-pay regulations within the European Union with the aim of serving as an input into a discussion whether a

  17. Process Integration Design Methods for Water Conservation and Wastewater Reduction in Industry. Part 3: Experience of Industrial Application

    DEFF Research Database (Denmark)

    Wenzel, Henrik; Dunn, Russell; Gottrup, Lene

    2002-01-01

    This paper is Part 3 in a three part series of papers addressing operational techniques for applying mass integration principles to design in industry with special focus on water conservation and wastewater reduction. The presented techniques derive from merging US and Danish experience with indu......This paper is Part 3 in a three part series of papers addressing operational techniques for applying mass integration principles to design in industry with special focus on water conservation and wastewater reduction. The presented techniques derive from merging US and Danish experience......’s experience with defining the scope of the system and with identifying water flow constraints and water quality constraints is discussed. It is shown, how physical constraints for the system design often set a limit for the sophistication of the water recycle network and thereby also a limit for how...... sophisticated the method for system design should be. Finally, pinch analysis and system designs for water recycling in a practical case study are shown, documenting large water saving potentials and achievements....

  18. Optimization of filtration for reduction of lung dose from Rn decay products: Part I--Theoretical

    International Nuclear Information System (INIS)

    Curling, C.A.; Rudnick, S.N.; Ryan, P.B.; Moeller, D.W.

    1990-01-01

    A theoretical model was developed for the optimization of filter characteristics that would minimize the dose from the inhalation of Rn decay products. Modified forms of the Jacobi-Porstendorfer room model and the Jacobi-Eisfeld lung dose model were chosen for use in the mathematical simulation. Optimized parameters of the filter were the thickness, solidity, and fiber diameter. For purposes of the calculations, the room dimensions, air exchange rate, particle-size distribution and concentration, and the Rn concentration were specified. The resulting computer-aided optimal design was a thin filter (the minimum thickness used in the computer model was 0.1 mm) having low solidity (the minimum solidity used was 0.5%) and large diameter fibers (the maximum diameter used was 100 microns). The simulation implies that a significant reduction in the dose rate can be achieved using a well-designed recirculating filter system. The theoretical model, using the assumption of ideal mixing, predicts an 80% reduction in the dose rate, although inherent in this assumption is the movement of 230 room volumes per hour through the fan

  19. Pollution sources and groundwater quality in the Coastal region of the Yugoslav part of the Danube

    International Nuclear Information System (INIS)

    Komatina, S.

    1997-01-01

    In order to access the vulnerability and risk of the aquifer system in the Yugoslav part of the Danube, as the primary source of drinking water for a numerically substantial community, industrial purposes and irrigation, as well as a high concentration of civil, industrial and agricultural activities (hence, a potential source of pollution of the groundwater resources through land occupation and use as well as the disposal of solid and liquid wastes), a great hydro-geophysical exploration was performed. Within the lower part of the plain, exploratory test of Salinac field, near Smederevo town, was particularly investigated. The reason why is because that part is also an area of the mouth of the Velika Morava into the Danube, where Derdap reservoir is located. Task of complex exploration was to delineate the aquifer, obtain appropriate parameters (groundwater level, groundwater chemistry, clay content, filtration characteristics and physical parameters of geological functions), as well as to map the aquifer vulnerability, in order to prevent and moderate a harmful influence of the performed reservoir on the environment (increased groundwater infiltration from the reservoir into surrounding rocks, permanent groundwater level raising, etc.). Based on the results, zoning of the study area according to the aquifer vulnerability has been done. Then, land-use planning and development of strategy for groundwater protection and management was possible. In the paper, not only sources of contamination, characteristics of pollutants and their influence on the groundwater quality was presented, but also content of organic matters, phosphates and nitrogen compounds, etc. Further, means of protection and management are discussed, as well as the appropriate legal regulations. (author)

  20. Getting to the Source: a Survey of Quantitative Data Sources Available to the Everyday Librarian: Part 1: Web Server Log Analysis

    Directory of Open Access Journals (Sweden)

    Lisa Goddard

    2007-03-01

    Full Text Available This is the first part of a two‐part article that provides a survey of data sources which are likely to be immediately available to the typical practitioner who wishes to engage instatistical analysis of collections and services within his or her own library. Part I outlines the data elements which can be extracted from web server logs, and discusses web log analysis tools. Part II looks at logs, reports, and data sources from proxy servers, resource vendors, link resolvers, federated search engines, institutional repositories, electronic reference services, and the integrated library system.

  1. Numerical Investigation of Resistance Reduction of Fishing Boat by Improving Stern Part

    OpenAIRE

    Baso, Suandar

    2013-01-01

    In recent years, to achieve a goal of reducing greenhouse gas, a fishing boat which is very economical on gas should be needed. Over the last two decades, improvements of bow part in fishing boat have been researched to reduce water resistance. Moreover, stern End Bulb research took place mostly in Japan. No one finds universal knowledge for reducing drag resistance because many fishing boats run with individual catching styles for each fish. It is also difficult to appropriate some technique...

  2. Development and pilot production of three ingot-source beryllium sheet metal parts

    International Nuclear Information System (INIS)

    Floyd, D.R.

    1975-01-01

    Results of an extensive development program aimed at making three, separate, structural components from beryllium, using sheet-metal fabrication methods, are presented. Ingot-source beryllium sheet at thicknesses of 0.100, 0.125, and 0.170 inch is formed in a fully-recrystallized and in a partially-recrystallized condition. The tensile yield strength is 26,000 psi after full recrystallization. After partial recrystallization, tensile yield strength is between 35,000 and 45,000 psi, depending upon sheet thickness, heat treat temperature, and time at temperature. The high yield strength is retained in the parts after forming. (U.S.)

  3. Research on numerical method for multiple pollution source discharge and optimal reduction program

    Science.gov (United States)

    Li, Mingchang; Dai, Mingxin; Zhou, Bin; Zou, Bin

    2018-03-01

    In this paper, the optimal method for reduction program is proposed by the nonlinear optimal algorithms named that genetic algorithm. The four main rivers in Jiangsu province, China are selected for reducing the environmental pollution in nearshore district. Dissolved inorganic nitrogen (DIN) is studied as the only pollutant. The environmental status and standard in the nearshore district is used to reduce the discharge of multiple river pollutant. The research results of reduction program are the basis of marine environmental management.

  4. Proceedings of the workshop on ion source issues relevant to a pulsed spallation neutron source: Part 1: Workshop summary

    International Nuclear Information System (INIS)

    Schroeder, L.; Leung, K.N.; Alonso, J.

    1994-10-01

    The workshop reviewed the ion-source requirements for high-power accelerator-driven spallation neutron facilities, and the performance of existing ion sources. Proposals for new facilities in the 1- to 5-MW range call for a widely differing set of ion-source requirements. For example, the source peak current requirements vary from 40 mA to 150 mA, while the duty factor ranges from 1% to 9%. Much of the workshop discussion centered on the state-of-the-art of negative hydrogen ion source (H - ) technology and the present experience with Penning and volume sources. In addition, other ion source technologies, for positive ions or CW applications were reviewed. Some of these sources have been operational at existing accelerator complexes and some are in the source-development stage on test stands

  5. Several natural indicators of radial well ageing at the Belgrade groundwater source, part 1.

    Science.gov (United States)

    Dimkić, M; Pusić, M; Vidovic, D; Petković, A; Boreli-Zdravković, D

    2011-01-01

    Over time, the radial collector wells of the Belgrade Groundwater Source, located in the alluvial sediments of the Sava River, exhibit a decline in discharge and a reduction in operating efficiency due to well ageing. An increase in hydraulic losses at the lateral screens, due to chemical and biochemical clogging, has been identified as the primary cause. Certain hydrogeological, hydrochemical and microbiological parameters reflect the well-ageing process and can, therefore, be considered as its indicators. An indicator-based determination of scale is an important aspect in the selection of appropriate well locations, structural characteristics, and maintenance approaches. Well ageing was studied over a period of 5 years (2005-2009). The objective was to investigate the causes of well ageing. The correlations established between the groundwater redox potential, the total iron concentration in groundwater, the grain-size distribution of the aquifer, and well discharge, are presented in the paper.

  6. Characterization of the radon source in North-Central Florida. Final report part 1 -- Final project report; Final report part 2 -- Technical report

    International Nuclear Information System (INIS)

    1997-01-01

    This report contains two separate parts: Characterization of the Radon Source in North-Central Florida (final report part 1 -- final project report); and Characterization of the Radon Source in North-Central Florida (technical report). The objectives were to characterize the radon 222 source in a region having a demonstrated elevated indoor radon potential and having geology, lithology, and climate that are different from those in other regions of the U.S. where radon is being studied. Radon availability and transport in this region were described. Approaches for predicting the radon potential of lands in this region were developed

  7. Multisource inverse-geometry CT. Part II. X-ray source design and prototype

    Energy Technology Data Exchange (ETDEWEB)

    Neculaes, V. Bogdan, E-mail: neculaes@ge.com; Caiafa, Antonio; Cao, Yang; De Man, Bruno; Edic, Peter M.; Frutschy, Kristopher; Gunturi, Satish; Inzinna, Lou; Reynolds, Joseph; Vermilyea, Mark; Wagner, David; Zhang, Xi; Zou, Yun [GE Global Research, Niskayuna, New York 12309 (United States); Pelc, Norbert J. [Department of Radiology, Stanford University, Stanford, California 94305 (United States); Lounsberry, Brian [Healthcare Science Technology, GE Healthcare, West Milwaukee, Wisconsin 53219 (United States)

    2016-08-15

    Purpose: This paper summarizes the development of a high-power distributed x-ray source, or “multisource,” designed for inverse-geometry computed tomography (CT) applications [see B. De Man et al., “Multisource inverse-geometry CT. Part I. System concept and development,” Med. Phys. 43, 4607–4616 (2016)]. The paper presents the evolution of the source architecture, component design (anode, emitter, beam optics, control electronics, high voltage insulator), and experimental validation. Methods: Dispenser cathode emitters were chosen as electron sources. A modular design was adopted, with eight electron emitters (two rows of four emitters) per module, wherein tungsten targets were brazed onto copper anode blocks—one anode block per module. A specialized ceramic connector provided high voltage standoff capability and cooling oil flow to the anode. A matrix topology and low-noise electronic controls provided switching of the emitters. Results: Four modules (32 x-ray sources in two rows of 16) have been successfully integrated into a single vacuum vessel and operated on an inverse-geometry computed tomography system. Dispenser cathodes provided high beam current (>1000 mA) in pulse mode, and the electrostatic lenses focused the current beam to a small optical focal spot size (0.5 × 1.4 mm). Controlled emitter grid voltage allowed the beam current to be varied for each source, providing the ability to modulate beam current across the fan of the x-ray beam, denoted as a virtual bowtie filter. The custom designed controls achieved x-ray source switching in <1 μs. The cathode-grounded source was operated successfully up to 120 kV. Conclusions: A high-power, distributed x-ray source for inverse-geometry CT applications was successfully designed, fabricated, and operated. Future embodiments may increase the number of spots and utilize fast read out detectors to increase the x-ray flux magnitude further, while still staying within the stationary target inherent

  8. Oxidative capacity of the Mexico City atmosphere – Part 1: A radical source perspective

    Directory of Open Access Journals (Sweden)

    R. Volkamer

    2010-07-01

    found already at 10:00 a.m., i.e., more than 2.5 h before solar noon. O3/alkene reactions are indirectly responsible for ~33% of these radicals. Our measurements and analysis comprise a database that enables testing of the representation of radical sources and radical chain reactions in photochemical models.

    Since the photochemical processing of pollutants in the MCMA is radical limited, our analysis identifies the drivers for ozone and SOA formation. We conclude that reductions in VOC emissions provide an efficient opportunity to reduce peak concentrations of these secondary pollutants, because (1 about 70% of radical production is linked to VOC precursors; (2 lowering the VOC/NOx ratio has the further benefit of reducing the radical re-cycling efficiency from radical chain reactions (chemical amplification of radical sources; (3 a positive feedback is identified: lowering the rate of radical production from organic precursors also reduces that from inorganic precursors, like ozone, as pollution export from the MCMA caps the amount of ozone that accumulates at a lower rate inside the MCMA. Continued VOC reductions will in the future result in decreasing peak concentrations of ozone and SOA in the MCMA.

  9. An extended dual input dual output three level Z source inverter with improved switch loss reduction technique

    Directory of Open Access Journals (Sweden)

    N.B. Deshmukh

    2016-12-01

    Full Text Available Multilevel inverter (MLI is a proven technology used for industrial applications due to low output total harmonic distortion (THD, high power handling capability and low active device rating. Dual output inverter is a recent trend associated with inverter topologies for specialized applications. This paper deals with three phase three level dual input dual output inverter topology with minimum active device count. Reduction in switch count leads to reduction in losses and improves reliability. Both the input sources share power equally as neutral point current ripple is maintained low. For further reduction in switching losses at higher switching frequencies, the concept of “no switching zone” or discontinuous pulse width modulation (DPWM has been put forth recently. This paper proposes modification in the placement of “no switching zone” in order to optimize switching losses and output THD (output filtering requirements for low power factor load. This study also proposes novel graphical approach to analyze the loss reduction along with its effect on output THD. The sinusoidal PWM (SPWM is used which gives satisfactory switching loss reduction without complex calculations. Moreover, the proposed topology is generalized to provide dual output at higher voltage levels. It is seen that the components reduction phenomenon becomes more pronounced as number of levels goes on increasing. The proposed converter is simulated in MATLAB software environment and results are obtained.

  10. Dominant superiority of nuclear power in the reduction of CO2 emissions. Part 2

    International Nuclear Information System (INIS)

    Kase, Susumu

    2011-01-01

    Soon after the oil crisis in 1973, then French president Giscard d'Estaing and his administration very strongly persuaded the French people to make the nation's electrical power consist mainly of nuclear power. As a result, by the beginning of 1990's, as high as 80% of electric power generated in France became nuclear (30% in Japan). Add the share 9% of hydroelectric power, 89% of electric power generated in France is now free of fossil fuel, and emission of green house gases per capita in France is now 42% less than in Japan. What Japan should do first of all in the coming future is to emulate the French experience. That should result in a 35% reduction in green house gas emission by 2030 at an acceptable cost. To put that in practice we first must overcome the now considerably weakened but still stubbornly remaining national sentiment against nuclear power. It will take a very strong top to bottom persuasion by the leading sector of the society. As to this matter the author stressed in a separate paper that mankind, like in the instinctive language capability, possesses a born instinctive way of life to believe in and live by the dominant spirit of the time. And unfortunately the current spirit of the time still is tainted with irrational dislike of nuclear power which can be weakened by strong and persistent persuasion. (author)

  11. Reduction-oxidation Enabled Glass-ceramics to Stainless Steel Bonding Part II interfacial bonding analysis

    Energy Technology Data Exchange (ETDEWEB)

    Dai, Steve Xunhu [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-09-01

    Among glass-ceramic compositions modified with a variety of oxidants (AgO, FeO, NiO, PbO, SnO, CuO, CoO, MoO3 and WO3) only CuO and CoO doped glass-ceramics showed existence of bonding oxides through reduction-oxidation (redox) at the GC-SS interface. The CuO-modified glass-ceramics demonstrate the formation of a continuous layer of strong bonding Cr2O3 at the interface in low partial oxygen (PO2) atmosphere. However, in a local reducing atmosphere, the CuO is preferentially reduced at the surface of glass-ceramic rather than the GC-SS interface for redox. The CoO-modified glass-ceramics demonstrate improved GC-SS bonding. But the low mobility of Co++ ions in the GC limited the amount of CoO that can diffuse to and participate in redox at the interface.

  12. Reduction of lead pollution from vehicular emissions in cairo Part 1: Comparison of alternative solutions

    International Nuclear Information System (INIS)

    El-Haggar, S.M.; Saleh, S.K.; El-Kady, M.A.

    1996-01-01

    It has been recognized for decades that the major source of lead pollution is lead additives to automotive fuels. This problem has been countered in most countries in europe and Usa by introducing alternative anti-knock chemicals and unleaded gasoline. In egypt lead is still being added to gasoline in large quantities. However, progress has been made, and unleaded gasoline is currently being produced in Alexandria. Nevertheless, the major pollution problem remains in the Greater Cairo region as indicated by the atmospheric lead levels and the lead blood levels of the children in Cairo. The aim of the present study is to find an optimum solution to this problem. A comparison of the different solutions is conducted in order to come up with the most feasible solution to this urgent problem. In conclusion it has been demonstrated that the elimination of lead additives, with its huge positives effects on the country environment, proved to be profitable. 4 figs., 2 tabs

  13. DrSPINE - New approach to data reduction and analysis for neutron spin echo experiments from pulsed and reactor sources

    International Nuclear Information System (INIS)

    Zolnierczuk, P.A.; Ohl, M.; Holderer, O.; Monkenbusch, M.

    2015-01-01

    Neutron spin echo (NSE) method at a pulsed neutron source presents new challenges to the data reduction and analysis as compared to the instruments installed at reactor sources. The main advantage of the pulsed source NSE is the ability to resolve the neutron wavelength and collect neutrons over a wider bandwidth. This allows us to more precisely determine the symmetry phase and measure the data for several Q-values at the same time. Based on the experience gained at the SNS NSE - the first, and to date the only one, NSE instrument installed at a pulsed spallation source, we propose a novel and unified approach to the NSE data processing called DrSPINE. The goals of the DrSPINE project are: -) exploit better symmetry phase determination due to the broader bandwidth at a pulsed source; -) take advantage of larger Q coverage for TOF instruments; -) use objective statistical criteria to get the echo fits right; -) provide robust reduction with report generation; -) incorporate absolute instrument calibration; and -) allow for background subtraction. The software must be able to read the data from various instruments, perform data integrity, consistency and compatibility checks and combine the data from compatible sets, partial scans, etc. We chose to provide a console-based interface with the ability to process macros (scripts) for batch evaluation. And last and not the least, a good software package has to provide adequate documentation. DrSPINE software is currently under development

  14. Breast cancer prevention knowledge, beliefs, and information sources between non-Hispanic and Hispanic college women for risk reduction focus.

    Science.gov (United States)

    Kratzke, Cynthia; Amatya, Anup; Vilchis, Hugo

    2015-02-01

    Although growing research focuses on breast cancer screenings, little is known about breast cancer prevention with risk reduction awareness for ethnic differences among college-age women. This study examined breast cancer prevention knowledge, beliefs, and information sources between non-Hispanic and Hispanic college women. Using a cross-sectional study, women at a university in the Southwest completed a 51-item survey about breast cancer risk factors, beliefs, and media and interpersonal information sources. The study was guided by McGuire's Input Output Persuasion Model. Of the 546 participants, non-Hispanic college women (n = 277) and Hispanic college women (n = 269) reported similar basic knowledge levels of modifiable breast cancer risk factors for alcohol consumption (52 %), obesity (72 %), childbearing after age 35 (63 %), and menopausal hormone therapy (68 %) using bivariate analyses. Most common information sources were Internet (75 %), magazines (69 %), provider (76 %) and friends (61 %). Least common sources were radio (44 %), newspapers (34 %), and mothers (36 %). Non-Hispanic college women with breast cancer family history were more likely to receive information from providers, friends, and mothers. Hispanic college women with a breast cancer family history were more likely to receive information from their mothers. Breast cancer prevention education for college women is needed to include risk reduction for modifiable health behavior changes as a new focus. Health professionals may target college women with more information sources including the Internet or apps.

  15. Responses of water environment to tidal flat reduction in Xiangshan Bay: Part I hydrodynamics

    Science.gov (United States)

    Li, Li; Guan, Weibing; Hu, Jianyu; Cheng, Peng; Wang, Xiao Hua

    2018-06-01

    Xiangshan Bay consists of a deep tidal channel and three shallow inlets. A large-scale tidal flat has been utilized through coastal construction. To ascertain the accumulate influences of these engineering projects upon the tidal dynamics of the channel-inlets system, this study uses FVCOM to investigate the tides and flow asymmetries of the bay, and numerically simulate the long-term variations of tidal dynamics caused by the loss of tidal flats. It was found that the reduction of tidal flat areas from 1963 to 2010 slightly dampened M2 tidal amplitudes (0.1 m, ∼6%) and advanced its phases by reducing shoaling effects, while amplified M4 tidal amplitudes (0.09 m, ∼27%) and advanced its phases by reducing bottom friction, in the inner bay. Consequently, the ebb dominance was dampened indicated by reduced absolute value of elevation skewness (∼20%) in the bay. The tides and tidal asymmetry were impacted by the locations, areas and slopes of the tidal flats through changing tidal prism, shoaling effect and bottom friction, and consequently impacted tidal duration asymmetry in the bay. Tides and tidal asymmetry were more sensitive to the tidal flat at the head of the bay than the side bank. Reduced/increased tidal flat slopes around the Tie inlet dampened the ebb dominance. Tidal flat had a role in dissipating the M4 tide rather than generating it, while the advection only play a secondary role in generating the M4 tide. The full-length tidal flats reclamation would trigger the reverse of ebb to flood dominance in the bay. This study would be applicable for similar narrow bays worldwide.

  16. Influence of Carbon Sources and Electron Shuttles on Ferric Iron Reduction by Cellulomonas sp. Strain ES6

    Energy Technology Data Exchange (ETDEWEB)

    Erin K. Field; Robin Gerlach; Sridhar Viamajala; Laura K. Jennings; Alfred B. Cunningham; Brent M. Peyton; William A. Apel

    2011-09-01

    The reduction of hexavalent chromium, Cr(VI), to trivalent chromium, Cr(III), can be an important aspect of remediation processes at Department of Energy (DOE) and other contaminated sites. Cellulomonas species are found at several Cr(VI) contaminated and uncontaminated locations at the DOE site in Hanford, Washington. Members of this genus have demonstrated the ability to effectively reduce Cr(VI) to Cr(III) fermentatively and therefore play a potential role in hexavalent chromium remediation at this site. Batch studies were conducted with Cellulomonas sp. strain ES6 to assess the influence of various carbon sources, iron minerals, and electron shuttling compounds on Cr(VI) reduction. These chemical species are likely to be present in these terrestrial environments during in situ bioremediation. Results indicated that there were a number of interactions between these compounds that influenced Cr(VI) reduction rates. The type of carbon source as well as the type of electron shuttle present influenced Cr(VI) reduction rates. When an electron shuttle, such as anthraquinone-2,6-disulfonate (AQDS), was present in the system, reduction rates increased significantly. Biologically reduced AQDS (AHDS) reduced Cr(VI) almost instantaneously. The presence of iron minerals and their concentrations did not significantly influence Cr(VI) reduction rates. However, strain ES6 or AQDS could directly reduce surface-associated Fe(III) to Fe(II) which was capable of reducing Cr(VI) at a near instantaneous rate. These results suggest the rate limiting step in these systems is the transfer of electrons from strain ES6 to the intermediate or terminal electron acceptor whether that is Cr(VI), Fe(III), or AQDS.

  17. Influence of Carbon Sources and Electron Shuttles on Ferric Iron Reduction by Cellulomonas sp. Strain ES6

    Energy Technology Data Exchange (ETDEWEB)

    Dr Robin Gerlach; Erin K. Field; Sridhar Viamajala; Brent M. Peyton; William A. Apel; Al B. Cunningham

    2011-09-01

    Microbially reduced iron minerals can reductively transform a variety of contaminants including heavy metals, radionuclides, chlorinated aliphatics, and nitroaromatics. A number of Cellulomonas spp. strains, including strain ES6, isolated from aquifer samples obtained at the U.S. Department of Energy's Hanford site in Washington, have been shown to be capable of reducing Cr(VI), TNT, natural organic matter, and soluble ferric iron [Fe(III)]. This research investigated the ability of Cellulomonas sp. strain ES6 to reduce solid phase and dissolved Fe(III) utilizing different carbon sources and various electron shuttling compounds. Results suggest that Fe(III) reduction by and growth of strain ES6 was dependent upon the type of electron donor, the form of iron present, and the presence of synthetic or natural organic matter, such as anthraquinone-2,6-disulfonate (AQDS) or humic substances. This research suggests that Cellulomonas sp. strain ES6 could play a significant role in metal reduction in the Hanford subsurface and that the choice of carbon source and organic matter addition can allow for independent control of growth and iron reduction activity.

  18. Cr(Vi) reduction capacity of activated sludge as affected by nitrogen and carbon sources, microbial acclimation and cell multiplication

    International Nuclear Information System (INIS)

    Ferro Orozco, A.M.; Contreras, E.M.; Zaritzky, N.E.

    2010-01-01

    The objectives of the present work were: (i) to analyze the capacity of activated sludge to reduce hexavalent chromium using different carbon sources as electron donors in batch reactors, (ii) to determine the relationship between biomass growth and the amount of Cr(VI) reduced considering the effect of the nitrogen to carbon source ratio, and (iii) to determine the effect of the Cr(VI) acclimation stage on the performance of the biological chromium reduction assessing the stability of the Cr(VI) reduction capacity of the activated sludge. The highest specific Cr(VI) removal rate (q Cr ) was attained with cheese whey or lactose as electron donors decreasing in the following order: cheese whey ∼ lactose > glucose > citrate > acetate. Batch assays with different nitrogen to carbon source ratio demonstrated that biological Cr(VI) reduction is associated to the cell multiplication phase; as a result, maximum Cr(VI) removal rates occur when there is no substrate limitation. The biomass can be acclimated to the presence of Cr(VI) and generate new cells that maintain the ability to reduce chromate. Therefore, the activated sludge process could be applied to a continuous Cr(VI) removal process.

  19. Implementation of variance-reduction techniques for Monte Carlo nuclear logging calculations with neutron sources

    NARCIS (Netherlands)

    Maucec, M

    2005-01-01

    Monte Carlo simulations for nuclear logging applications are considered to be highly demanding transport problems. In this paper, the implementation of weight-window variance reduction schemes in a 'manual' fashion to improve the efficiency of calculations for a neutron logging tool is presented.

  20. Tracking Poverty Reduction in Bhutan: Income Deprivation Alongside Deprivation in Other Sources of Happiness

    Science.gov (United States)

    Santos, Maria Emma

    2013-01-01

    This paper analyses poverty reduction in Bhutan between two points in time--2003 and 2007--from a multidimensional perspective. The measures estimated include consumption expenditure as well as other indicators which are directly (when possible) or indirectly associated to valuable functionings, namely, health, education, access to electricity,…

  1. DISSOLVED OXYGEN REDUCTION IN THE DIII-D NEUTRAL BEAM ION SOURCE COOLING SYSTEM

    International Nuclear Information System (INIS)

    YIP, H.; BUSATH, J.; HARRISON, S.

    2004-03-01

    OAK-B135 Neutral beam ion sources (NBIS) are critical components for the neutral beam injection system supporting the DIII-D tokamak. The NBIS must be cooled with 3028 (ell)/m (800 gpm) of de-ionized and de-oxygenated water to protect the sources from overheating and failure. These ions sources are currently irreplaceable. Since the water cooled molybdenum components will oxidize in water almost instantaneously in the presence of dissolved oxygen (DO), de-oxygenation is extremely important in the NBIS water system. Under normal beam operation the DO level is kept below 5 ppb. However, during weeknights and weekends when neutral beam is not in operation, the average DO level is maintained below 10 ppb by periodic circulation with a 74.6 kW (100 hp) pump, which consumes significant power. Experimental data indicated evidence of continuous oxygen diffusion through non-metallic hoses in the proximity of the NBIS. Because of the intermittent flow of the cooling water, the DO concentration at the ion source(s) could be even higher than measured downstream, and hence the concern of significant localized oxidation/corrosion. A new 3.73 kW (5 hp) auxiliary system, installed in the summer of 2003, is designed to significantly reduce the peak and the time-average DO levels in the water system and to consume only a fraction of the power

  2. The Reduction of Vertical Interchannel Crosstalk: The Analysis of Localisation Thresholds for Natural Sound Sources

    Directory of Open Access Journals (Sweden)

    Rory Wallis

    2017-03-01

    Full Text Available In subjective listening tests, natural sound sources were presented to subjects as vertically-oriented phantom images from two layers of loudspeakers, ‘height’ and ‘main’. Subjects were required to reduce the amplitude of the height layer until the position of the resultant sound source matched that of the same source presented from the main layer only (the localisation threshold. Delays of 0, 1 and 10 ms were applied to the height layer with respect to the main, with vertical stereophonic and quadraphonic conditions being tested. The results of the study showed that the localisation thresholds obtained were not significantly affected by sound source or presentation method. Instead, the only variable whose effect was significant was interchannel time difference (ICTD. For ICTD of 0 ms, the median threshold was −9.5 dB, which was significantly lower than the −7 dB found for both 1 and 10 ms. The results of the study have implications both for the recording of sound sources for three-dimensional (3D audio reproduction formats and also for the rendering of 3D images.

  3. Speckle noise reduction on a laser projection display via a broadband green light source.

    Science.gov (United States)

    Yu, Nan Ei; Choi, Ju Won; Kang, Heejong; Ko, Do-Kyeong; Fu, Shih-Hao; Liou, Jiun-Wei; Kung, Andy H; Choi, Hee Joo; Kim, Byoung Joo; Cha, Myoungsik; Peng, Lung-Han

    2014-02-10

    A broadband green light source was demonstrated using a tandem-poled lithium niobate (TPLN) crystal. The measured wavelength and temperature bandwidth were 6.5 nm and 100 °C, respectively, spectral bandwidth was 36 times broader than the periodically poled case. Although the conversion efficiency was smaller than in the periodic case, the TPLN device had a good figure of merit owing to the extremely large bandwidth for wavelength and temperature. The developed broadband green light source exhibited speckle noise approximately one-seventh of that in the conventional approach for a laser projection display.

  4. Technology and applications of broad-beam ion sources used in sputtering. Part II. Applications

    International Nuclear Information System (INIS)

    Harper, J.M.E.; Cuomo, J.J.; Kaufman, H.R.

    1982-01-01

    The developments in broad-beam ion source technology described in the companion paper (Part I) have stimulated a rapid expansion in applications to materials processing. These applications are reviewed here, beginning with a summary of sputtering mechanisms. Next, etching applications are described, including microfabrication and reactive ion beam etching. The developing area of surface layer applications is summarized, and related to the existing fields of oxidation and implantation. Next, deposition applications are reviewed, including ion-beam sputter deposition and the emerging technique of ion-assisted vapor deposition. Many of these applications have been stimulated by the development of high current ion sources operating in the energy range of tens of hundreds of eV. It is in this energy range that ion-activated chemical etching is efficient, self-limiting compound layers can be grown, and the physical properties of vapor-deposited films can be modified. In each of these areas, broad ion beam technology provides a link between other large area plasma processes and surface analytical techniques using ion beams

  5. Monte Carlo modeling and analyses of YALINA- booster subcritical assembly Part II: pulsed neutron source

    International Nuclear Information System (INIS)

    Talamo, A.; Gohar, M.Y.A.; Rabiti, C.

    2008-01-01

    One of the most reliable experimental methods for measuring the kinetic parameters of a subcritical assembly is the Sjoestrand method applied to the reaction rate generated from a pulsed neutron source. This study developed a new analytical methodology for characterizing the kinetic parameters of a subcritical assembly using the Sjoestrand method, which allows comparing the analytical and experimental time dependent reaction rates and the reactivity measurements. In this methodology, the reaction rate, detector response, is calculated due to a single neutron pulse using MCNP/MCNPX computer code or any other neutron transport code that explicitly simulates the fission delayed neutrons. The calculation simulates a single neutron pulse over a long time period until the delayed neutron contribution to the reaction is vanished. The obtained reaction rate is superimposed to itself, with respect to the time, to simulate the repeated pulse operation until the asymptotic level of the reaction rate, set by the delayed neutrons, is achieved. The superimposition of the pulse to itself was calculated by a simple C computer program. A parallel version of the C program is used due to the large amount of data being processed, e.g. by the Message Passing Interface (MPI). The new calculation methodology has shown an excellent agreement with the experimental results available from the YALINA-Booster facility of Belarus. The facility has been driven by a Deuterium-Deuterium or Deuterium-Tritium pulsed neutron source and the (n,p) reaction rate has been experimentally measured by a 3 He detector. The MCNP calculation has utilized the weight window and delayed neutron biasing variance reduction techniques since the detector volume is small compared to the assembly volume. Finally, this methodology was used to calculate the IAEA benchmark of the YALINA-Booster experiment

  6. Specific power reduction of an ion source due to heating and cathode sputtering of electrodes

    International Nuclear Information System (INIS)

    Hamilton, G.U.; Semashko, N.N.

    The potentialities and limitations of the water-cooled ion-optical system of the ion source designed for continuous operation of the high-power neutral beam injector are determined. The following problems are analyzed: thermal expansion and deformation of electrodes, electrode sputtering as a result of bombardment, and heat transfer to turbulent flow of water

  7. Contrasting geochemical trends in the fertile and refractory parts of the NE Atlantic mantle source

    Science.gov (United States)

    Tronnes, R. G.; Debaille, V.; Brandon, A. D.; Waight, T. E.; Graham, D. W.; Williams, A.; Lee, C. A.

    2008-12-01

    Primitive alkaline basalts from the Icelandic off-rift volcanic zones and Jan Mayen represent low-degree melts from the fertile parts of the NE Atlantic mantle. Olivine tholeiites and picrites from the Icelandic rift zones and nearby oceanic spreading ridges are formed by protracted decompressional melting. The V-shaped ridges along the Reykjanes, Kolbeinsey and Aegir ridges indicate that ascending source material is supplied by a pulsating plume and deflected laterally for distances of about 1000 km from Iceland (Jones et al. GGG 2002; Breivik et al. JGR 2006). Plume material deflected in the direction of the rift zones and spreading ridges undergoes extensive melting at shallow level, whereas material deflected in other directions flows laterally at deeper levels and remains largely unmelted and more fertile. The comparison of a sample suite of primitive off-rift basalts from Iceland and Jan Mayen (Debaille et al., in prep.) with olivine tholeiites and picrites from the Icelandic rift zones (mainly Brandon et al. GCA 2007) demonstrate opposing geochemical trends. The degree of source enrichment, expressed by the La/Sm-ratio, is positively and negatively correlated with 87/86Sr and 143/144Nd throughout the entire range of depleted rift zone tholeiites and enriched off-rift basalts. In the rift zone tholeiites the La/Sm-ratio has negative correlations with Mg# and Mg-content and positive correlations with 187/188Os and 3/4He. These four trends have opposite equivalents for the off-rift basalts. The most enriched and alkaline basalts from Jan Mayen and Snæfellsnes have the lowest 3/4He of 6-9*Ra and 187/188Os of 0.12-0.13. The trends seem to require a source component with ancient melt depletion and subsequent enrichment. A subcontinental lithospheric mantle keel (SCLM) is the most likely origin for the enriched component with high LILE, La/Sm and 87/86Sr and low 143/144Nd, 3/4He and 187/188Os. The most enriched alkaline basalts have notably higher Mg# and Mg and

  8. Synthesis of AuPd alloyed nanoparticles via room-temperature electron reduction with argon glow discharge as electron source.

    Science.gov (United States)

    Yang, Manman; Wang, Zongyuan; Wang, Wei; Liu, Chang-Jun

    2014-01-01

    Argon glow discharge has been employed as a cheap, environmentally friendly, and convenient electron source for simultaneous reduction of HAuCl4 and PdCl2 on the anodic aluminum oxide (AAO) substrate. The thermal imaging confirms that the synthesis is operated at room temperature. The reduction is conducted with a short time (30 min) under the pressure of approximately 100 Pa. This room-temperature electron reduction operates in a dry way and requires neither hydrogen nor extra heating nor chemical reducing agent. The analyses using X-ray photoelectron spectroscopy (XPS) confirm all the metallic ions have been reduced. The characterization with X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM) shows that AuPd alloyed nanoparticles are formed. There also exist some highly dispersed Au and Pd monometallic particles that cannot be detected by XRD and transmission electron microscopy (TEM) because of their small particle sizes. The observed AuPd alloyed nanoparticles are spherical with an average size of 14 nm. No core-shell structure can be observed. The room-temperature electron reduction can be operated in a larger scale. It is an easy way for the synthesis of AuPd alloyed nanoparticles.

  9. Open source projects as incubators of innovation: From niche phenomenon to integral part of the software industry

    OpenAIRE

    Schrape, Jan-Felix

    2017-01-01

    Over the last 20 years, open source development has become an integral part of the software industry and a key component of the innovation strategies of all major IT providers. Against this backdrop, this paper seeks to develop a systematic overview of open source communities and their socio-economic contexts. I begin with a reconstruction of the genesis of open source software projects and their changing relation- ships to established IT companies. This is followed by the identification of f...

  10. Contaminant Flux Reduction Barriers for Managing Difficult-to-Treat Source Zones in Unconsolidated Media

    Science.gov (United States)

    2017-06-20

    estimated viscosity of 3-4 cP.  Solutions-IES Novel Silica Gel/Veg-Oil Grout: 5 wt- % of emulsified vegetable oil (EVO), 10 wt-% of sodium...site must have a lower low permeability unit such as a clay to prevent up flow; and a four sided barrier is recommended (three sided barriers are...depth to groundwater (ង ft)  Transmissive zone preferably with an underlying clay layer  Good accessibility to source zone  Availability of

  11. Stator Current Harmonic Reduction in a Novel Half Quasi-Z-Source Wind Power Generation System

    Directory of Open Access Journals (Sweden)

    Shoudao Huang

    2016-09-01

    Full Text Available The generator stator current gets distorted with unacceptable levels of total harmonic distortion (THD because impedance-source wind power generation systems use three-phase diode rectifiers. The stator current harmonics will cause increasing losses and torque ripple, which reduce the efficiency and stability of the system. This paper proposes a novel half quasi-Z-source inverter (H-qZSI for grid-connected wind power generation systems, which can reduce the generator stator current harmonics a great deal. When H-qZSI operates in the shoot-through zero state, the derivative of the generator stator current is only determined by the instantaneous value of the generator stator voltage, so the nonlinear relationship between generator stator current and stator voltage is improved compared with the traditional impedance-source inverter. Theoretically, it is indicated that the stator current harmonics can be reduced effectively by means of the proposed H-qZSI. Finally, simulation and experimental results are given to verify the theoretical analysis.

  12. Market Analysis and Consumer Impacts Source Document. Part I. The Motor Vehicle Market in the Late 1970's

    Science.gov (United States)

    1980-12-01

    The source document on motor vehicle market analysis and consumer impact consists of three parts. Part I is an integrated overview of the motor vehicle market in the late 1970's, with sections on the structure of the market, motor vehicle trends, con...

  13. Modelling study of boundary-layer ozone over northern China - Part II: Responses to emission reductions during the Beijing Olympics

    Science.gov (United States)

    Tang, Guiqian; Zhu, Xiaowan; Xin, Jinyuan; Hu, Bo; Song, Tao; Sun, Yang; Wang, Lili; Wu, Fangkun; Sun, Jie; Cheng, Mengtian; Chao, Na; Li, Xin; Wang, Yuesi

    2017-09-01

    The implementation of emission reduction measures during the Olympics provided a valuable opportunity to study regional photochemical pollution over northern China. In this study, the fifth-generation Pennsylvania State University/National Centre for Atmospheric Research Mesoscale Model and Community Multiscale Air Quality model system was applied to conduct two sets of modelling analyses of the period from July 20 to September 20, 2008, to illustrate the influences of emission reduction measures on regional photochemical pollution over northern China during the Beijing Olympics. The results indicated that the implementation of emission control measures decreased the concentrations of ozone (O3) precursors, namely nitrogen oxide (NOx) and volatile organic compounds (VOCs), throughout the boundary layer. The concentrations of these compounds were reduced by 45% in the central urban area of Beijing at the ground level. Although the average O3 concentration in the central urban area increased by more than 8 ppbv, the total oxidant concentration decreased significantly by more than 5 ppbv. Greater O3 concentrations mainly occurred during periods with weak photochemical reactions. During periods of strong photochemical production, the O3 concentration decreased significantly due to a weakening vertical circulation between the lower and upper boundary layer. Consequently, the number of days when the O3 concentration exceeded 100 ppbv decreased by 25% in Beijing. The emission control measures altered the sensitivity of the regional O3 production. The coordinated control region of NOx and VOCs expanded, and the control region of VOCs decreased in size. The reduction of non-point-source emissions, such as fugitive VOCs and vehicles, was more useful for controlling regional photochemical pollution over northern China.

  14. Identification of abiotic and biotic reductive dechlorination in a chlorinated ethene plume after thermal source remediation by means of isotopic and molecular biology tools

    DEFF Research Database (Denmark)

    Badin, Alice; Broholm, Mette Martina; Jacobsen, Carsten S.

    2016-01-01

    Thermal tetrachloroethene (PCE) remediation by steam injection in a sandy aquifer led to the release of dissolved organic carbon (DOC) from aquifer sediments resulting in more reduced redox conditions, accelerated PCE biodegradation, and changes in microbial populations. These changes were...... documented by comparing data collected prior to the remediation event and eight years later. Based on the premise that dual C-Cl isotope slopes reflect ongoing degradation pathways, the slopes associated with PCE and TCE suggest the predominance of biotic reductive dechlorination near the source area. PCE...... is supported by the relative lack of Dhc in the downgradient part of the plume. The results of this study show that thermal remediation can enhance the biodegradation of chlorinated ethenes, and that this effect can be traced to the mobilisation of DOC due to steam injection. This, in turn, results in more...

  15. Quad Cities Unit 2 Main Steam Line Acoustic Source Identification and Load Reduction

    International Nuclear Information System (INIS)

    DeBoo, Guy; Ramsden, Kevin; Gesior, Roman

    2006-01-01

    The Quad Cities Units 1 and 2 have a history of steam line vibration issues. The implementation of an Extended Power Up-rate resulted in significant increases in steam line vibration as well as acoustic loading of the steam dryers, which led to equipment failures and fatigue cracking of the dryers. This paper discusses the results of extensive data collection on the Quad Cities Unit 2 replacement dryer and the Main Steam Lines. This data was taken with the intent of identifying acoustic sources in the steam system. Review of the data confirmed that vortex shedding coupled column resonance in the relief and safety valve stub pipes were the principal sources of large magnitude acoustic loads in the main steam system. Modifications were developed in sub-scale testing to alter the acoustic properties of the valve standpipes and add acoustic damping to the system. The modifications developed and installed consisted of acoustic side branches that were attached to the Electromatic Relief Valve (ERV) and Main Steam Safety Valve (MSSV) attachment pipes. Subsequent post-modification testing was performed in plant to confirm the effectiveness of the modifications. The modifications have been demonstrated to reduce vibration loads at full Extended Power Up-rate (EPU) conditions to levels below those at Original Licensed Thermal Power (OLTP). (authors)

  16. Stratospheric ozone reduction and its relation to natural and man made sources

    Energy Technology Data Exchange (ETDEWEB)

    Isaksen, I S [Oslo Univ. (Norway). Dept. of Geophysics

    1996-12-31

    Approximately 90 % of the total ozone mass is in the stratosphere (between approximately 12 and 50 km), the rest is in the troposphere (below 12 km). The global distribution of ozone in the stratosphere and its variation over time have been studied extensively over several decades. These studies include observations by ground based instruments (e.g. Dobson instruments), instruments on airborne platforms (e.g. ozone sondes) and on satellites, and model studies which simulate the chemical and dynamical behaviour of the stratosphere. These studies have given good information about the processes which determine the ozone distribution, and how man made emissions affect the distribution. Observations have revealed that there are large year to year variations in stratospheric ozone above a particular location. These variations are difficult to predict as they are connected to irregular weather patterns. However, the observations have shown that there has been a long term decrease in stratospheric ozone on a global scale during the last two decades. The decrease has been most pronounced during the last five to six years and is seen both in the Northern and the Southern Hemispheres. The strong decrease in stratospheric ozone over the Antarctic continent, which has been observed since the mid 80s, and which has reduced the total ozone column with more than 50 % compared with earlier observations, is proven to be a result of increased man made emissions of CFCs. There are also mounting evidences that Northern Hemispheric ozone reductions observed since 1980 are connected to man made emissions of CFCs

  17. Stratospheric ozone reduction and its relation to natural and man made sources

    Energy Technology Data Exchange (ETDEWEB)

    Isaksen, I.S. [Oslo Univ. (Norway). Dept. of Geophysics

    1995-12-31

    Approximately 90 % of the total ozone mass is in the stratosphere (between approximately 12 and 50 km), the rest is in the troposphere (below 12 km). The global distribution of ozone in the stratosphere and its variation over time have been studied extensively over several decades. These studies include observations by ground based instruments (e.g. Dobson instruments), instruments on airborne platforms (e.g. ozone sondes) and on satellites, and model studies which simulate the chemical and dynamical behaviour of the stratosphere. These studies have given good information about the processes which determine the ozone distribution, and how man made emissions affect the distribution. Observations have revealed that there are large year to year variations in stratospheric ozone above a particular location. These variations are difficult to predict as they are connected to irregular weather patterns. However, the observations have shown that there has been a long term decrease in stratospheric ozone on a global scale during the last two decades. The decrease has been most pronounced during the last five to six years and is seen both in the Northern and the Southern Hemispheres. The strong decrease in stratospheric ozone over the Antarctic continent, which has been observed since the mid 80s, and which has reduced the total ozone column with more than 50 % compared with earlier observations, is proven to be a result of increased man made emissions of CFCs. There are also mounting evidences that Northern Hemispheric ozone reductions observed since 1980 are connected to man made emissions of CFCs

  18. Increase of COP for heat transformer in water purification systems. Part I - Increasing heat source temperature

    International Nuclear Information System (INIS)

    Siqueiros, J.; Romero, R.J.

    2007-01-01

    The integration of a water purification system in a heat transformer allows a fraction of heat obtained by the heat transformer to be recycled, increasing the heat source temperature. Consequently, the evaporator and generator temperatures are also increased. For any operating conditions, keeping the condenser and absorber temperatures and also the heat load to the evaporator and generator, a higher value of COP is obtained when only the evaporator and generator temperatures are increased. Simulation with proven software compares the performance of the modeling of an absorption heat transformer for water purification (AHTWP) operating with water/lithium bromide, as the working fluid-absorbent pair. Plots of enthalpy-based coefficients of performance (COP ET ) and the increase in the coefficient of performance (COP) are shown against absorber temperature for several thermodynamic operating conditions. The results showed that proposed (AHTWP) system is capable of increasing the original value of COP ET more than 120%, by recycling part of the energy from a water purification system. The proposed system allows to increase COP values from any experimental data for water purification or any other distillation system integrated to a heat transformer, regardless of the actual COP value and any working fluid-absorbent pair

  19. Design, implementation and practice of JBEI-ICE: an open source biological part registry platform and tools.

    Science.gov (United States)

    Ham, Timothy S; Dmytriv, Zinovii; Plahar, Hector; Chen, Joanna; Hillson, Nathan J; Keasling, Jay D

    2012-10-01

    The Joint BioEnergy Institute Inventory of Composable Elements (JBEI-ICEs) is an open source registry platform for managing information about biological parts. It is capable of recording information about 'legacy' parts, such as plasmids, microbial host strains and Arabidopsis seeds, as well as DNA parts in various assembly standards. ICE is built on the idea of a web of registries and thus provides strong support for distributed interconnected use. The information deposited in an ICE installation instance is accessible both via a web browser and through the web application programming interfaces, which allows automated access to parts via third-party programs. JBEI-ICE includes several useful web browser-based graphical applications for sequence annotation, manipulation and analysis that are also open source. As with open source software, users are encouraged to install, use and customize JBEI-ICE and its components for their particular purposes. As a web application programming interface, ICE provides well-developed parts storage functionality for other synthetic biology software projects. A public instance is available at public-registry.jbei.org, where users can try out features, upload parts or simply use it for their projects. The ICE software suite is available via Google Code, a hosting site for community-driven open source projects.

  20. Google vs. the Library (Part III): Assessing the Quality of Sources Found by Undergraduates

    Science.gov (United States)

    Georgas, Helen

    2015-01-01

    This study assesses and compares the quality of sources found by undergraduate students when doing research using both Google and a library (federated) search tool. Thirty undergraduates were asked to find four sources (one book, two articles, and one additional source of their choosing) related to a selected research topic. Students used both…

  1. Nuclear fuel technology - Determination of uranium in solutions, uranium hexafluoride and solids - Part 2: Iron(II) reduction/cerium(IV) oxidation titrimetric method

    International Nuclear Information System (INIS)

    2004-01-01

    This first edition of ISO 7097-1 together with ISO 7097-2:2004 cancels and replaces ISO 7097:1983, which has been technically revised, and ISO 9989:1996. ISO 7097 consists of the following parts, under the general title Nuclear fuel technology - Determination of uranium in solutions, uranium hexafluoride and solids: Part 1: Iron(II) reduction/potassium dichromate oxidation titrimetric method; Part 2: Iron(II) reduction/cerium(IV) oxidation titrimetric method. This part 2. of ISO 7097 describes procedures for determination of uranium in solutions, uranium hexafluoride and solids. The procedures described in the two independent parts of this International Standard are similar: this part uses a titration with cerium(IV) and ISO 7097-1 uses a titration with potassium dichromate

  2. Nuclear fuel technology - Determination of uranium in solutions, uranium hexafluoride and solids - Part 1: Iron(II) reduction/potassium dichromate oxidation titrimetric method

    International Nuclear Information System (INIS)

    2004-01-01

    This first edition of ISO 7097-1 together with ISO 7097-2:2004 cancels and replaces ISO 7097:1983, which has been technically revised, and ISO 9989:1996. ISO 7097 consists of the following parts, under the general title Nuclear fuel technology - Determination of uranium in solutions, uranium hexafluoride and solids: Part 1: Iron(II) reduction/potassium dichromate oxidation titrimetric method; Part 2: Iron(II) reduction/cerium(IV) oxidation titrimetric method. This part 1. of ISO 7097 describes procedures for the determination of uranium in solutions, uranium hexafluoride and solids. The procedures described in the two independent parts of this International Standard are similar: this part uses a titration with potassium dichromate and ISO 7097-2 uses a titration with cerium(IV)

  3. Fibrates are an essential part of modern anti-dyslipidemic arsenal: spotlight on atherogenic dyslipidemia and residual risk reduction

    Directory of Open Access Journals (Sweden)

    Tenenbaum Alexander

    2012-10-01

    related to the effects on glucose metabolism and insulin resistance. Bezafibrate is the only clinically available pan - (alpha, beta, gamma PPAR balanced activator. Bezafibrate decreases blood glucose level, HbA1C, insulin resistance and reduces the incidence of T2DM compared to placebo or other fibrates. Among major fibrates, bezafibrate appears to have the strongest and fenofibrate the weakest effect on HDL-C. Current therapeutic use of statins as monotherapy is still leaving many patients with atherogenic dyslipidemia at high risk for coronary events because even intensive statin therapy does not eliminate the residual cardiovascular risk associated with low HDL and/or high triglycerides. As compared with statin monotherapy (effective mainly on LDL-C levels and plaque stabilization, the association of a statin with a fibrate will also have a major impact on triglycerides, HDL and LDL particle size. Moreover, in the specific case of bezafibrate one could expect neutralizing of the adverse pro-diabetic effect of statins. Though muscle pain and myositis is an issue in statin/fibrate treatment, adverse interaction appears to occur to a significantly greater extent when gemfibrozil is administered. However, bezafibrate and fenofibrate seems to be safer and better tolerated. Combined fibrate/statin therapy is more effective in achieving a comprehensive lipid control and may lead to additional cardiovascular risk reduction, as could be suggested for fenofibrate following ACCORD Lipid study subgroup analysis and for bezafibrate on the basis of one small randomized study and multiple observational data. Therefore, in appropriate patients with atherogenic dyslipidemia fibrates- either as monotherapy or combined with statins – are consistently associated with reduced risk of cardiovascular events. Fibrates currently constitute an indispensable part of the modern anti-dyslipidemic arsenal for patients with atherogenic dyslipidemia.

  4. Fibrates are an essential part of modern anti-dyslipidemic arsenal: spotlight on atherogenic dyslipidemia and residual risk reduction.

    Science.gov (United States)

    Tenenbaum, Alexander; Fisman, Enrique Z

    2012-10-11

    glucose metabolism and insulin resistance. Bezafibrate is the only clinically available pan - (alpha, beta, gamma) PPAR balanced activator. Bezafibrate decreases blood glucose level, HbA1C, insulin resistance and reduces the incidence of T2DM compared to placebo or other fibrates. Among major fibrates, bezafibrate appears to have the strongest and fenofibrate the weakest effect on HDL-C. Current therapeutic use of statins as monotherapy is still leaving many patients with atherogenic dyslipidemia at high risk for coronary events because even intensive statin therapy does not eliminate the residual cardiovascular risk associated with low HDL and/or high triglycerides. As compared with statin monotherapy (effective mainly on LDL-C levels and plaque stabilization), the association of a statin with a fibrate will also have a major impact on triglycerides, HDL and LDL particle size. Moreover, in the specific case of bezafibrate one could expect neutralizing of the adverse pro-diabetic effect of statins. Though muscle pain and myositis is an issue in statin/fibrate treatment, adverse interaction appears to occur to a significantly greater extent when gemfibrozil is administered. However, bezafibrate and fenofibrate seems to be safer and better tolerated. Combined fibrate/statin therapy is more effective in achieving a comprehensive lipid control and may lead to additional cardiovascular risk reduction, as could be suggested for fenofibrate following ACCORD Lipid study subgroup analysis and for bezafibrate on the basis of one small randomized study and multiple observational data. Therefore, in appropriate patients with atherogenic dyslipidemia fibrates- either as monotherapy or combined with statins - are consistently associated with reduced risk of cardiovascular events. Fibrates currently constitute an indispensable part of the modern anti-dyslipidemic arsenal for patients with atherogenic dyslipidemia.

  5. Overlooked Talent Sources and Corporate Strategies for Affirmative Action. Part II

    Science.gov (United States)

    Iacobelli, John L.; Muczyk, Jan P.

    1975-01-01

    Part Two of the two-part article describes corporate strategies for affirmative action in order to obtain the most qualified individuals available for professional positions among minority and female candidates. (Author/BP)

  6. New complete sample of identified radio sources. Part 2. Statistical study

    International Nuclear Information System (INIS)

    Soltan, A.

    1978-01-01

    Complete sample of radio sources with known redshifts selected in Paper I is studied. Source counts in the sample and the luminosity - volume test show that both quasars and galaxies are subject to the evolution. Luminosity functions for different ranges of redshifts are obtained. Due to many uncertainties only simplified models of the evolution are tested. Exponential decline of the liminosity with time of all the bright sources is in a good agreement both with the luminosity- volume test and N(S) realtion in the entire range of observed flux densities. It is shown that sources in the sample are randomly distributed in scales greater than about 17 Mpc. (author)

  7. Active3 noise reduction

    International Nuclear Information System (INIS)

    Holzfuss, J.

    1996-01-01

    Noise reduction is a problem being encountered in a variety of applications, such as environmental noise cancellation, signal recovery and separation. Passive noise reduction is done with the help of absorbers. Active noise reduction includes the transmission of phase inverted signals for the cancellation. This paper is about a threefold active approach to noise reduction. It includes the separation of a combined source, which consists of both a noise and a signal part. With the help of interaction with the source by scanning it and recording its response, modeling as a nonlinear dynamical system is achieved. The analysis includes phase space analysis and global radial basis functions as tools for the prediction used in a subsequent cancellation procedure. Examples are given which include noise reduction of speech. copyright 1996 American Institute of Physics

  8. Bomb reduction of uranium tetrafluoride. Part II: Influence of the addition elements in the reduction process; Reduccion del tetrafluoruro de uranio en bomba cerrada. Parte II: Influencia de elementos de adicion en la reducion

    Energy Technology Data Exchange (ETDEWEB)

    Anca Abati, R; Lopez Rodriguez, M

    1962-07-01

    This work shows the influence of uranium oxide and uranyl fluoride in the reduction of uranium with Ca and Mg. These additions are more harmful when using smaller bombs. The uranyl fluoride has influence in the reduction process; the curves yield-concentration shows two regions depending upon the salt concentration. The behaviour of this addition in these regions can be explained following the different decompositions that can take place during the reduction process. (Author) 9 refs.

  9. Reduction of Methane Emission during Slurry Storage by the Addition of Effective Microorganisms and Excessive Carbon Source from Brewing Sugar.

    Science.gov (United States)

    Bastami, Mohd Saufi B; Jones, Davey L; Chadwick, David R

    2016-11-01

    Storing livestock manure is the primary stage of manure management where microbial processes and chemical reactions result in the release of methane (CH), nitrous oxide (NO), ammonia (NH), and carbon dioxide (CO). This study examined the reduction of CH emissions from slurry storage under two temperatures (cool [10°C] and warm [30°C]) when a glucose-rich substrate (brewing sugar) and activated effective microorganisms were applied at 10% (w/w) and 5% (v/w), respectively. Brewing sugar addition influenced microbial anaerobic respiration, resulting in a reduction of slurry pH to <5.0, through "self-acidification" caused by lactic acid production. Subsequently, CH emissions were significantly reduced by 87 and 99% in the cool and warm environments, respectively. The effective microorganism treatment did not change the chemical characteristics of the slurry but reduced CH emissions by 17 and 27% ( < 0.05) in the cool and warm environments, respectively. These results suggest that self-acidification after addition of a carbon source may be a promising alternative to slurry acidification using concentrated acids. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

  10. Beamlines of the biomedical imaging and therapy facility at the Canadian light source - part 3

    Science.gov (United States)

    Wysokinski, Tomasz W.; Chapman, Dean; Adams, Gregg; Renier, Michel; Suortti, Pekka; Thomlinson, William

    2015-03-01

    The BioMedical Imaging and Therapy (BMIT) facility provides synchrotron-specific imaging and radiation therapy capabilities [1-4]. We describe here the Insertion Device (ID) beamline 05ID-2 with the beam terminated in the SOE-1 (Secondary Optical Enclosure) experimental hutch. This endstation is designed for imaging and therapy research primarily in animals ranging in size from mice to humans to horses, as well as tissue specimens including plants. Core research programs include human and animal reproduction, cancer imaging and therapy, spinal cord injury and repair, cardiovascular and lung imaging and disease, bone and cartilage growth and deterioration, mammography, developmental biology, gene expression research as well as the introduction of new imaging methods. The source for the ID beamline is a multi-pole superconducting 4.3 T wiggler [5]. The high field gives a critical energy over 20 keV. The high critical energy presents shielding challenges and great care must be taken to assess shielding requirements [6-9]. The optics in the POE-1 and POE-3 hutches [4,10] prepare a monochromatic beam that is 22 cm wide in the last experimental hutch SOE-1. The double crystal bent-Laue or Bragg monochromator, or the single-crystal K-edge subtraction (KES) monochromator provide an energy range appropriate for imaging studies in animals (20-100+ keV). SOE-1 (excluding the basement structure 4 m below the experimental floor) is 6 m wide, 5 m tall and 10 m long with a removable back wall to accommodate installation and removal of the Large Animal Positioning System (LAPS) capable of positioning and manipulating animals as large as a horse [11]. This end-station also includes a unique detector positioner with a vertical travel range of 4.9 m which is required for the KES imaging angle range of +12.3° to -7.3°. The detector positioner also includes moveable shielding integrated with the safety shutters. An update on the status of the other two end-stations at BMIT, described

  11. Beamlines of the biomedical imaging and therapy facility at the Canadian light sourcepart 3

    International Nuclear Information System (INIS)

    Wysokinski, Tomasz W.; Chapman, Dean; Adams, Gregg; Renier, Michel; Suortti, Pekka; Thomlinson, William

    2015-01-01

    The BioMedical Imaging and Therapy (BMIT) facility provides synchrotron-specific imaging and radiation therapy capabilities [1–4]. We describe here the Insertion Device (ID) beamline 05ID-2 with the beam terminated in the SOE-1 (Secondary Optical Enclosure) experimental hutch. This endstation is designed for imaging and therapy research primarily in animals ranging in size from mice to humans to horses, as well as tissue specimens including plants. Core research programs include human and animal reproduction, cancer imaging and therapy, spinal cord injury and repair, cardiovascular and lung imaging and disease, bone and cartilage growth and deterioration, mammography, developmental biology, gene expression research as well as the introduction of new imaging methods. The source for the ID beamline is a multi-pole superconducting 4.3 T wiggler [5]. The high field gives a critical energy over 20 keV. The high critical energy presents shielding challenges and great care must be taken to assess shielding requirements [6–9]. The optics in the POE-1 and POE-3 hutches [4,10] prepare a monochromatic beam that is 22 cm wide in the last experimental hutch SOE-1. The double crystal bent-Laue or Bragg monochromator, or the single-crystal K-edge subtraction (KES) monochromator provide an energy range appropriate for imaging studies in animals (20–100+ keV). SOE-1 (excluding the basement structure 4 m below the experimental floor) is 6 m wide, 5 m tall and 10 m long with a removable back wall to accommodate installation and removal of the Large Animal Positioning System (LAPS) capable of positioning and manipulating animals as large as a horse [11]. This end-station also includes a unique detector positioner with a vertical travel range of 4.9 m which is required for the KES imaging angle range of +12.3° to –7.3°. The detector positioner also includes moveable shielding integrated with the safety shutters. An update on the status of the other two end-stations at BMIT

  12. Beamlines of the biomedical imaging and therapy facility at the Canadian light sourcepart 3

    Energy Technology Data Exchange (ETDEWEB)

    Wysokinski, Tomasz W., E-mail: bmit@lightsource.ca [Canadian Light Source, Saskatoon, SK (Canada); Chapman, Dean [Anatomy and Cell Biology, University of Saskatchewan, Saskatoon, SK (Canada); Adams, Gregg [Western College of Veterinary Medicine, Saskatoon, SK (Canada); Renier, Michel [European Synchrotron Radiation Facility, Grenoble (France); Suortti, Pekka [Department of Physics, University of Helsinki (Finland); Thomlinson, William [Department of Physics, University of Saskatchewan, Saskatoon, SK (Canada)

    2015-03-01

    The BioMedical Imaging and Therapy (BMIT) facility provides synchrotron-specific imaging and radiation therapy capabilities [1–4]. We describe here the Insertion Device (ID) beamline 05ID-2 with the beam terminated in the SOE-1 (Secondary Optical Enclosure) experimental hutch. This endstation is designed for imaging and therapy research primarily in animals ranging in size from mice to humans to horses, as well as tissue specimens including plants. Core research programs include human and animal reproduction, cancer imaging and therapy, spinal cord injury and repair, cardiovascular and lung imaging and disease, bone and cartilage growth and deterioration, mammography, developmental biology, gene expression research as well as the introduction of new imaging methods. The source for the ID beamline is a multi-pole superconducting 4.3 T wiggler [5]. The high field gives a critical energy over 20 keV. The high critical energy presents shielding challenges and great care must be taken to assess shielding requirements [6–9]. The optics in the POE-1 and POE-3 hutches [4,10] prepare a monochromatic beam that is 22 cm wide in the last experimental hutch SOE-1. The double crystal bent-Laue or Bragg monochromator, or the single-crystal K-edge subtraction (KES) monochromator provide an energy range appropriate for imaging studies in animals (20–100+ keV). SOE-1 (excluding the basement structure 4 m below the experimental floor) is 6 m wide, 5 m tall and 10 m long with a removable back wall to accommodate installation and removal of the Large Animal Positioning System (LAPS) capable of positioning and manipulating animals as large as a horse [11]. This end-station also includes a unique detector positioner with a vertical travel range of 4.9 m which is required for the KES imaging angle range of +12.3° to –7.3°. The detector positioner also includes moveable shielding integrated with the safety shutters. An update on the status of the other two end-stations at BMIT

  13. Highlighting professional writing : on screen note-taking as part of writing from sources by professionals

    NARCIS (Netherlands)

    Melenhorst, M.S.

    2006-01-01

    Professionals in organizations often make use of source material in order to write an evaluation, a report or a recommendation. This task, also known as writing-from-sources, is increasingly being performed, either totally or partially, in a digital environment. Reasons for this could be that the

  14. Source profiles of volatile organic compounds (VOCs) measured in China: Part I

    Science.gov (United States)

    Liu, Ying; Shao, Min; Fu, Linlin; Lu, Sihua; Zeng, Limin; Tang, Dagang

    The profiles of major volatile organic compound (VOC) sources in China, including vehicle exhaust, gasoline vapor, paint, asphalt, industrial and residential coal burning, biomass burning, and the petrochemical industry, were experimentally determined. Source samples were taken using a dilution chamber for mobile and stationary sources, biomass burning in an actual Chinese farmer's house, and ambient air in a petrochemical industrial area. The concentrations of 92 VOC species were quantified using canister sampling and a gas chromatography-flame ionization detection/mass spectrometry system, and VOC source profiles were developed for source apportionment of VOCs in the Pearl River Delta region. Based on the measurement of source profiles, possible tracers for various emission sources were identified; e.g., 2-methylpentane and 1,3-butadiene could be used as tracers for vehicle exhaust; the characteristic compounds of architectural coating were aromatics such as toluene and m, p-xylene; the light hydrocarbons, namely n-butane, trans-2-butene, and n-pentane, dominated the composition of gasoline vapor; and n-nonane, n-decane, and n-undecane were found to be typical of diesel vapor and asphalt application processes. As different emission sources are characterized by overlapping VOC species, the ratio of possible VOC tracers could be used to assess the contribution of various sources. The ratios between n-butane and isobutane, 1,3-butadiene and isoprene, and the ratios of aromatics (e.g., toluene to benzene and ethylbenzene to m, p-xylene) in the measured sources were compared.

  15. Taming a Tiger in the City: Comparison of Motorized Backpack Applications and Source Reduction Against the Asian Tiger Mosquito, Aedes albopictus

    Science.gov (United States)

    2014-06-01

    TAMING A TIGER IN THE CITY: COMPARISON OF MOTORIZED BACKPACK APPLICATIONS AND SOURCE REDUCTION AGAINST THE ASIAN TIGER MOSQUITO, AEDES ALBOPICTUS...FONSECA2 AND ARY FARAJOLLAHI2,3,7 ABSTRACT. We evaluated 2 strategies to manage Aedes albopictus: 1) motorized backpack applications and 2) source...the community level. KEY WORDS Bacillus thuringiensis israelensis, Bti, methoprene, hand applications, backpack applications INTRODUCTION Aedes

  16. Catalysts for cleaner combustion of coal, wood and briquettes sulfur dioxide reduction options for low emission sources

    Energy Technology Data Exchange (ETDEWEB)

    Smith, P.V. [Global Environmental Solutions, Inc., Morton Grove, IL (United States)

    1995-12-31

    Coal fired, low emission sources are a major factor in the air quality problems facing eastern European cities. These sources include: stoker-fired boilers which feed district heating systems and also meet local industrial steam demand, hand-fired boilers which provide heat for one building or a small group of buildings, and masonary tile stoves which heat individual rooms. Global Environmental Systems is marketing through Global Environmental Systems of Polane, Inc. catalysts to improve the combustion of coal, wood or fuel oils in these combustion systems. PCCL-II Combustion Catalysts promotes more complete combustion, reduces or eliminates slag formations, soot, corrosion and some air pollution emissions and is especially effective on high sulfur-high vanadium residual oils. Glo-Klen is a semi-dry powder continuous acting catalyst that is injected directly into the furnace of boilers by operating personnel. It is a multi-purpose catalyst that is a furnace combustion catalyst that saves fuel by increasing combustion efficiency, a cleaner of heat transfer surfaces that saves additional fuel by increasing the absorption of heat, a corrosion-inhibiting catalyst that reduces costly corrosion damage and an air pollution reducing catalyst that reduces air pollution type stack emissions. The reduction of sulfur dioxides from coal or oil-fired boilers of the hand fired stoker design and larger, can be controlled by the induction of the Glo-Klen combustion catalyst and either hydrated lime or pulverized limestone.

  17. Basalt generation at the Apollo 12 site. Part 2: Source heterogeneity, multiple melts, and crustal contamination

    Science.gov (United States)

    Neal, Clive R.; Hacker, Matthew D.; Snyder, Gregory A.; Taylor, Lawrence A.; Liu, Yun-Gang; Schmitt, Roman A.

    1994-01-01

    The petrogenesis of Apollo 12 mare basalts has been examined with emphasis on trace-element ratios and abundances. Vitrophyric basalts were used as parental compositions for the modeling, and proportions of fractionating phases were determined using the MAGFOX prograqm of Longhi (1991). Crystal fractionation processes within crustal and sub-crustal magma chambers are evaluated as a function of pressure. Knowledge of the fractionating phases allows trace-element variations to be considered as either source related or as a product of post-magma-generation processes. For the ilmenite and olivine basalts, trace-element variations are inherited from the source, but the pigeonite basalt data have been interpreted with open-system evolution processes through crustal assimilation. Three groups of basalts have been examined: (1) Pigeonite basalts-produced by the assimilation of lunar crustal material by a parental melt (up to 3% assimilation and 10% crystal fractionation, with an 'r' value of 0.3). (2) Ilmenite basalts-produced by variable degrees of partial melting (4-8%) of a source of olivine, pigeonite, augite, and plagioclase, brought together by overturn of the Lunar Magma Ocean (LMO) cumulate pile. After generation, which did not exhaust any of the minerals in the source, these melts experienced closed-system crystal fractionation/accumulation. (3) Olivine basalts-produced by variable degrees of partial melting (5-10%) of a source of olivine, pigeonite, and augite. After generation, again without exhausting any of the minerals in the source, these melts evolved through crystal accumulation. The evolved liquid counterparts of these cumulates have not been sampled. The source compositions for the ilmenite and olivine basalts were calculated by assuming that the vitrophyric compositions were primary and the magmas were produced by non-modal batch melting. Although the magnitude is unclear, evaluation of these source regions indicates that both be composed of early- and

  18. Source apportionment of ambient volatile organic compounds in the Pearl River Delta, China: Part II

    Science.gov (United States)

    Liu, Ying; Shao, Min; Lu, Sihua; Chang, Chih-Chung; Wang, Jia-Lin; Fu, Linlin

    The chemical mass balance receptor model was applied to the source apportionment of 58 hydrocarbons measured at seven sites in a field campaign that examined regional air quality in the Pearl River Delta (PRD) region in the fall of 2004. A total of 12 volatile organic compound (VOC) emission sources were considered, including gasoline- and diesel-powered vehicle exhausts, headspace vapors of gasoline and diesel fuel, vehicle evaporative emissions, liquid petroleum gas (LPG) leakage, paint vapors, asphalt emissions from paved roads, biomass combustion, coal combustion, the chemical industry, and petroleum refineries. Vehicle exhaust was the largest source of VOCs, contributing to >50% of ambient VOCs at the three urban sites (Guangzhou, Foshan, and Zhongshan). LPG leakage played an important role, representing 8-16% of emissions at most sites in the PRD. Solvent usage was the biggest emitter of VOCs at Dongguan, an industrial site, contributing 33% of ambient VOCs. Similarly, at Xinken, a non-urban site, the evaporation of solvents and coatings was the largest emission source, accounting for 31% of emissions, probably because it was downwind of Dongguan. Local biomass combustion was a noticeable source of VOCs at Xinken; although its contribution was estimated at 14.3%, biomass combustion was the third largest VOC source at this site.

  19. A tsunami wave propagation analysis for the Ulchin Nuclear Power Plant considering the tsunami sources of western part of Japan

    International Nuclear Information System (INIS)

    Rhee, Hyun Me; Kim, Min Kyu; Sheen, Dong Hoon; Choi, In Kil

    2013-01-01

    The accident which was caused by a tsunami and the Great East-Japan earthquake in 2011 occurred at the Fukushima Nuclear Power Plant (NPP) site. It is obvious that the NPP accident could be incurred by the tsunami. Therefore a Probabilistic Tsunami Hazard Analysis (PTHA) for an NPP site should be required in Korea. The PTHA methodology is developed on the PSHA (Probabilistic Seismic Hazard Analysis) method which is performed by using various tsunami sources and their weights. In this study, the fault sources of northwestern part of Japan were used to analyze as the tsunami sources. These fault sources were suggested by the Atomic Energy Society of Japan (AESJ). To perform the PTHA, the calculations of maximum and minimum wave elevations from the result of tsunami simulations are required. Thus, in this study, tsunami wave propagation analysis were performed for developing the future study of the PTHA

  20. Manual hyperinflation partly prevents reductions of functional residual capacity in cardiac surgical patients--a randomized controlled trial

    NARCIS (Netherlands)

    Paulus, Frederique; Veelo, Denise P.; de Nijs, Selma B.; Beenen, Ludo F. M.; Bresser, Paul; de Mol, Bas A. J. M.; Binnekade, Jan M.; Schultz, Marcus J.

    2011-01-01

    Cardiac surgery is associated with post-operative reductions of functional residual capacity (FRC). Manual hyperinflation (MH) aims to prevent airway plugging, and as such could prevent the reduction of FRC after surgery. The main purpose of this study was to determine the effect of MH on

  1. FSD for operating NPPs as part of sustainable dose reduction - recontamination evaluation for the German PWR Grafenrheinfeld

    International Nuclear Information System (INIS)

    Stellwag, Bernhard; Hoffmann-Wankerl, Stephan; Schuetz, Sigrid; Jacob, Astrid

    2012-09-01

    Full-system decontamination (FSD) or replacement of steam generators (SG) and other large components in mature PWR plants results in large bare metal surfaces in the reactor system. The AREVA chemistry concept for sustainable dose rate reduction at such plants includes a passivation treatment for formation of high-quality oxide films in the reactor system and high pH operation in combination with zinc injection during subsequent power operation. The effectiveness of these measures has been proven by plant operation experience. The systematic evaluation of plant-specific experience is used for further optimization of the concept. These measures were also applied at the 1350 MW-class 4-loop PWR Grafenrheinfeld after an FSD with the AREVA decontamination process HP/CORD R UV in 28 th outage. The passivation treatment consisted of zinc injection during plant heat-up and parallel adjustment of a high pH value. It was carried out in the plant operation condition 'subcritical hot' for 200 hours and a pH (300 deg. C) of 7.1. During the cycle, the pH value was increased to 7.4 and zinc injection was continued. This paper evaluates the recontamination of the plant inclusive the first refueling outage since the FSD. The evaluation is based on routine chemistry and dose rate surveillance data and on the results of special measurement programs conducted at the plant before and after the FSD. Results of surface gamma activity measurements and fuel crud analyses are also described. Data is evaluated with regard to release, transport and deposition of corrosion products and nuclides in the reactor system. The plant-specific contamination sources and their pathways are outlined. Compared to the first refueling outage of the plant in 1983, the dose rate level at the main loops could be more than halved in spite of already activated core internals and crud on fuel assemblies, the in-core instrumentation and the control rods including guide assemblies and drive rods. The FSD

  2. Joint part-of-speech and dependency projection from multiple sources

    DEFF Research Database (Denmark)

    Johannsen, Anders Trærup; Agic, Zeljko; Søgaard, Anders

    2016-01-01

    for multiple tasks from multiple source languages, relying on parallel corpora available for hundreds of languages. When training POS taggers and dependency parsers on jointly projected POS tags and syntactic dependencies using our algorithm, we obtain better performance than a standard approach on 20...

  3. Converting the GSR part3 into a national regulations for the protection and safety of radiation sources

    International Nuclear Information System (INIS)

    Hatim, Abdulrahman

    2016-04-01

    The achievement and maintenance of a high level of Radiation Protection and Safety of Radiation Sources depends on a sound legal and governmental infrastructure, including a regulatory body with well-defined responsibilities and functions. The project aimed at converting the IAEA GRS Part 3 into National regulations in Sudan for the protection against the harmful effects of ionizing radiation and safety of radiation sources. The regulations developed covered general requirements for radiation protection, verification of safety, planned exposure situations, emergency exposure situations and existing exposure situation. The Government of Sudan is expected to empower the Sudanese Nuclear Radiological Regulatory Authority (SNRAA) and other relevant authorities to undertake the conversion of IAEA GSR Part 3 into national regulations to be used to regulate all facilities and activities in Sudan. (au)

  4. Rapporteur Report: Sources and Exposure Metrics for RF Epidemiology (Part 1) (invited paper)

    Energy Technology Data Exchange (ETDEWEB)

    Allen, S

    1999-07-01

    A variety of sources was considered illustrating the predominantly uniform exposure at a distance and highly non-uniform exposures close to sources. The measurement of both electric and magnetic fields was considered for near field situations but where possible the use of induced body currents was judged to be the preferred metric. The salient features affecting exposure to fields from mobile telephones and their base stations were discussed for both existing and third generation systems. As an aid to future cancer studies, high resolution numerical modelling was used to illustrate left/right exposure discrimination of bilateral organs in the head. Factors influencing both numerical and experimental dosimetry were discussed and studies to investigate the ability to appropriately rank exposure were considered important areas for research. (author)

  5. Rapporteur Report: Sources and Exposure Metrics for RF Epidemiology (Part 1) (invited paper)

    International Nuclear Information System (INIS)

    Allen, S.

    1999-01-01

    A variety of sources was considered illustrating the predominantly uniform exposure at a distance and highly non-uniform exposures close to sources. The measurement of both electric and magnetic fields was considered for near field situations but where possible the use of induced body currents was judged to be the preferred metric. The salient features affecting exposure to fields from mobile telephones and their base stations were discussed for both existing and third generation systems. As an aid to future cancer studies, high resolution numerical modelling was used to illustrate left/right exposure discrimination of bilateral organs in the head. Factors influencing both numerical and experimental dosimetry were discussed and studies to investigate the ability to appropriately rank exposure were considered important areas for research. (author)

  6. Ionospheric disturbances due to underground nuclear explosions and other sources: an elementary discussion, Part I

    International Nuclear Information System (INIS)

    Wouters, L.F.

    1971-01-01

    The possible effect of verticle ground surface motion on the ionosphere, as a consequence of acoustic propagation, is discussed. Estimates of R. F. phase path perturbations are developed for several representative sources and several propagative modes (both terrestrial and atmospheric). In particular, amplitude models for ionospheric density perturbations are used. The discrimination of earth quakes and nuclear explosive disturbances is considered and some detailed properties of the extended atmosphere are described. A list of references is provided. (U.S.)

  7. Market Analysis and Consumer Impacts Source Document. Part II. Review of Motor Vehicle Market and Consumer Expenditures on Motor Vehicle Transportation

    Science.gov (United States)

    1980-12-01

    This source document on motor vehicle market analysis and consumer impacts consists of three parts. Part II consists of studies and review on: motor vehicle sales trends; motor vehicle fleet life and fleet composition; car buying patterns of the busi...

  8. Red Maple (Acer rubrum) Aerial Parts as a Source of Bioactive Phenolics.

    Science.gov (United States)

    Zhang, Yan; Ma, Hang; Yuan, Tao; Seeram, Navindra P

    2015-08-01

    The bark and stems of red maple (Acer rubrum) are reported to contain bioactive phenolics but its aerial parts, namely, flowers and leaves, remain largely unexplored. This is unfortunate considering that various parts of the red maple were used for traditional medicinal purposes by the indigenous peoples of eastern North America, where this species is found. Herein, we report the identification of twenty-five (1-25) phenolics, including two new galloyl derivatives (1 and 2), from red maple flowers and leaves. Of these, ten compounds (1-10), including the new compounds, were isolated and identified by NMR and HRESIMS data while the remaining fifteen compounds (11-25) were identified by HPLC-DAD analyses (by comparison with chemical standards). The isolates (1-10), along with the clinical drug, acarbose, were evaluated for their alpha-glucosidase enzyme inhibitory activities.

  9. Rapporteur Report: Sources and Exposure Metrics for ELF Epidemiology (Part 1) (invited paper)

    International Nuclear Information System (INIS)

    Matthes, R.

    1999-01-01

    High quality epidemiological studies on the possible link between exposure to non-ionizing radiation and human health effects are of great importance for radiation protection in this area. The main sources of ELF fields are domestic appliances, different electrical energy distribution systems and all kinds of electrical machinery and devices at the workplace. In general, ELF fields present in the environment, show complex temporal patterns and spatial distributions, depending on the generating source. The complete characterisation of the different field sources often requires highly sophisticated instrumentation, and this is therefore not feasible within the scope of epidemiological studies. On average, individual exposure from ELF fields is low in both the working environment and in residential areas. Only at certain workplaces are people subject to significant ELF exposure with regard to biological effects. Different methods have been developed to determine levels of exposure received by study subjects, with the aim to rank exposed and non-exposed groups in epidemiological studies. These include spot measurements, calculations or modelling. The different methods used to estimate total exposure in epidemiological studies may result to a differing extent in a misclassification of the study subjects. Equally important for future studies is the selection of the appropriate exposure metric. The most widely used metric so far is the time-weighted average and thus represents a quasi standard metric for use in epidemiological studies. Beside, wire codes have been used for a long time in residential studies and job titles are often used in occupational studies. On the basis of the experience gained in previous studies, it would be desirable to develop standardised, state-of-the-art protocols to improve exposure assessment. New surrogates and metrics were proposed as the basis for further studies. But only few of these have recently undergone preliminary testing. A

  10. On the physics of power, energy and economics of renewable electric energy sources - Part II

    International Nuclear Information System (INIS)

    Skoglund, Annika; Leijon, Mats; Waters, Rafael; Rehn, Alf; Lindahl, Marcus

    2010-01-01

    Renewable Energy Technologies (RETs) are often recognized as less competitive than traditional electric energy conversion systems. Obstacles with renewable electric energy conversion systems are often referred to the intermittency of the energy sources and the relatively high maintenance cost. However, due to an intensified discourse on climate change and its effects, it has from a societal point of view, become more desirable to adopt and install CO 2 neutral power plants. Even if this has increased the competitiveness of RETs in a political sense, the new goals for RET installations must also be met with economical viability. We propose that the direction of technical development, as well as the chosen technology in new installations, should not primarily be determined by policies, but by the basic physical properties of the energy source and the associated potential for inexpensive energy production. This potential is the basic entity that drives the payback of the investment of a specific RET power plant. With regard to this, we argue that the total electric energy conversion system must be considered if effective power production is to be achieved, with focus on the possible number of full loading hours and the Degree of Utilization. This will increase the cost efficiency and economical competitiveness of RET investments, and could enhance faster diffusion of new innovations and installations without over-optimistic subsidies. This paper elaborates on the overall problem of the economy of renewable electric energy conversion systems by studying the interface between physics, engineering and economy reported for RET power plants in different scientific publications. The core objective is to show the practical use of the Degree of Utilization and how the concept is crucial for the design and economical optimization disregarding subsidies. The results clearly indicate that the future political regulative frameworks should consider the choice of renewable energy

  11. Analysis of tellurium-silicon alloys. Part 1. Determination of tellurium by the reduction from perchloric acid solution

    International Nuclear Information System (INIS)

    Teperek, J.

    1977-01-01

    When 100-150 mg of tellurium is dissolved in the solution containing 20 cm 3 72 wt.% of perchloric acid, the reduction of tellurium to elementary form is possible only after adding 60-100 milimoles of HCl. The reduction is performed by adding 1 cm 3 of saturated sodium pyrosulphite solution (Na 2 S 2 O 5 ) and 10 cm 3 of 10 wt.% hydrazine hydrochloride solution (N 2 H 4 .2HCl) to 80-90 cm 3 of cold solution of Te in HClO 4 -HCl mixture. The reduction is completed after 3-5 min. of boiling. When 150-200 mg sample of Te-Si alloy is dissolved in 20 cm 3 of hot 72% per chloric acid, the separation of components is reached. Tellurium can be determinated in filtrate by proposed procedure with high accuracy and precision. (author)

  12. Sources

    International Nuclear Information System (INIS)

    Duffy, L.P.

    1991-01-01

    This paper discusses the sources of radiation in the narrow perspective of radioactivity and the even narrow perspective of those sources that concern environmental management and restoration activities at DOE facilities, as well as a few related sources. Sources of irritation, Sources of inflammatory jingoism, and Sources of information. First, the sources of irritation fall into three categories: No reliable scientific ombudsman to speak without bias and prejudice for the public good, Technical jargon with unclear definitions exists within the radioactive nomenclature, and Scientific community keeps a low-profile with regard to public information. The next area of personal concern are the sources of inflammation. This include such things as: Plutonium being described as the most dangerous substance known to man, The amount of plutonium required to make a bomb, Talk of transuranic waste containing plutonium and its health affects, TMI-2 and Chernobyl being described as Siamese twins, Inadequate information on low-level disposal sites and current regulatory requirements under 10 CFR 61, Enhanced engineered waste disposal not being presented to the public accurately. Numerous sources of disinformation regarding low level radiation high-level radiation, Elusive nature of the scientific community, The Federal and State Health Agencies resources to address comparative risk, and Regulatory agencies speaking out without the support of the scientific community

  13. Lecture notes on the safety aspects in the industrial applications of radiation sources - Part I

    International Nuclear Information System (INIS)

    The report comprises the notes of the lectures delivered on the safety aspects in industrial applications of radiation sources. The notes are presented in 9 chapters. Basic mathematics relevant to the topic and basic concepts of nuclear physics are introduced in chapters I and II respectively. Various aspects of interaction of radiation with matter and living cells are discussed in chapters III and IV respectively. The biological effects of ionizing radiations are described in chapter V. Various commonly used units of measurement of radiation and radioactivity are defined and explained and measuring methods of radiation exposure are described in chapter VI. Chapter VII deals with the maximum permissible levels of radiation, both internal and external, for occupational workers as well as population. The same chapter also deals with ICRP recommendations in this connection. Commonly used radiation detectors and instruments with associated electronics are described in chapter VIII. Production of radioisotopes, radiation sources and labelled compounds is described in chapter IX. A table of useful radioisotopes is appended to this chapter. A bibliography in which references are arranged chapterwise is also given at the end. (M.G.B.)

  14. Data Bank of Nuclear and Radiological Regulatory Authority, Part 2 . Software Package of Statistical Data of Sealed Sources

    International Nuclear Information System (INIS)

    Lashin, R.M.A.; Mahmoud, N.S.; Lashin, M.M.A.

    2012-01-01

    Protection of human, property and the environment is the main concern considered as a principal goal to form the Egyptian Nuclear and Radiological Regulatory Authority. That requires a lot of work, efforts, knowledge and aids for right and quick decision making. Internationally, the International Atomic Energy Agency (IAEA) developed a protection system for control and accounts the radioactive materials for the safe use and transport. Moreover, the protection system can prevent the theft of these materials or their use in terrorism. Here in, all radioactive sources shall be subjected to instructions, serious regulations and laws. In order to exercise these functions, it is necessary to accurately establish the appropriate information system to the regulatory body. This system must depend on using a modern technology to perform the work in most accurate and fullest manner in a Data Bank [1, 2]. The present work is the second part performed for the data bank, which consists of two parts: first part is concern about the open sources which executed before [3]. Second part is deal with the sealed sources. Describing here consolidated guidance help materials licenses. It also provides reviewers of such requests with the information and materials necessary to determine that the products are acceptable for licensing purposes. It provides the applicants and reviewers with information concerning how to file a request, a listing of the applicable regulations and industry standards, policies affecting evaluation and registration, administrative procedures to be followed, information on how to perform the evaluation and write a registration certificate, and the responsibilities of the registration certificate holder.

  15. Uranium tetrafluoride reduction closed bomb. Part I: Reduction process general conditions; Reduccion del tetrafluoruro de uranio en bomba cerrada. Part I. estudio de las variables generales del proceso de reduccion

    Energy Technology Data Exchange (ETDEWEB)

    Anca Abati, R; Lopez Rodriguez, M

    1961-07-01

    General conditions about the metallo thermic reduction in small bombs (250 and 800 gr. of uranium) has been investigated. Factors such as kind and granulometry of the magnesium used, magnesium excess and preheating temperature, which affect yields and metal quality have been considered. magnesium excess increased yields in a 15% in the small bomb, about the preheating temperature, there is a range between which yields and metal quality does not change. All tests have been made with graphite linings. (Author) 18 refs.

  16. Operation modes of the FALCON ion source as a part of the AMS cluster tool

    Directory of Open Access Journals (Sweden)

    Girka Oleksii

    2015-06-01

    Full Text Available The paper investigates the options to increase the production yield of temperature compensated surface acoustic wave (SAW devices with a defined range of operational frequencies. The paper focuses on the preparation of large wafers with SiO2 and AlN/Si3N4 depositions. Stability of the intermediate SiO2 layer is achieved by combining high power density UV radiation with annealing in high humidity environment. A uniform thickness of the capping AlN layer is achieved by local high-rate etching with a focused ion beam emitted by the FALCON ion source. Operation parameters and limitations of the etching process are discussed.

  17. A novel source convergence acceleration scheme for Monte Carlo criticality calculations, part I: Theory

    International Nuclear Information System (INIS)

    Griesheimer, D. P.; Toth, B. E.

    2007-01-01

    A novel technique for accelerating the convergence rate of the iterative power method for solving eigenvalue problems is presented. Smoothed Residual Acceleration (SRA) is based on a modification to the well known fixed-parameter extrapolation method for power iterations. In SRA the residual vector is passed through a low-pass filter before the extrapolation step. Filtering limits the extrapolation to the lower order Eigenmodes, improving the stability of the method and allowing the use of larger extrapolation parameters. In simple tests SRA demonstrates superior convergence acceleration when compared with an optimal fixed-parameter extrapolation scheme. The primary advantage of SRA is that it can be easily applied to Monte Carlo criticality calculations in order to reduce the number of discard cycles required before a stationary fission source distribution is reached. A simple algorithm for applying SRA to Monte Carlo criticality problems is described. (authors)

  18. Binary PVA bio-nanocomposites containing cellulose nanocrystals extracted from different natural sources: part I.

    Science.gov (United States)

    Fortunati, E; Puglia, D; Luzi, F; Santulli, C; Kenny, J M; Torre, L

    2013-09-12

    PVA bio-nanocomposites reinforced with cellulose nanocrystals (CNC) extracted from commercial microcrystalline cellulose (MCC) and from two types of natural fibres, Phormium tenax and Flax of the Belinka variety, were produced by solvent casting in water. Morphological, thermal, mechanical and transparency properties were studied while the respective efficiency of the extraction process of CNC from the three sources was evaluated. The effect of CNC types and content on PVA properties and water absorption capacity were also evaluated. Natural fibres offered higher levels of extraction efficiency when compared with MCC hydrolysis yield. Thermal analysis proved that CNC promotes the crystallization of the PVA matrix, while improving its plastic response. It was also clarified that all PVA/CNC systems remain transparent due to CNC dispersion at the nanoscale, while being all saturated after the first 18-24h of water absorption. Copyright © 2013 Elsevier Ltd. All rights reserved.

  19. Aspidosperma species as sources of antimalarials. Part III. A review of traditional use and antimalarial activity.

    Science.gov (United States)

    de Paula, Renata Cristina; Dolabela, Maria Fâni; de Oliveira, Alaíde Braga

    2014-03-01

    Several plant species belonging to the genus Aspidosperma are traditionally used in Brazil and other Meso- and South American countries for the treatment of malaria and fevers. These traditional uses were motivation for this review. A literature survey completed for this review has identified scientific bibliographical references to the use of 24 Aspidosperma species to treat malaria/fevers and to 19 species that have had their extracts and/or alkaloids evaluated, with good results, for in vitro and/or in vivo antimalarial activity. Indole alkaloids are typical constituents of Aspidosperma species. However, only 20 out of more than 200 known indole alkaloids isolated from this genus have been assayed for antimalarial activity. These data support the potential of Aspidosperma species as sources of antimalarials and the importance of research aimed at validating their use in the treatment of human malaria. Georg Thieme Verlag KG Stuttgart · New York.

  20. Towards Compatible and Interderivable Semantic Specifications for the Scheme Programming Language, Part II: Reduction Semantics and Abstract Machines

    DEFF Research Database (Denmark)

    Biernacka, Malgorzata; Danvy, Olivier

    2009-01-01

    We present a context-sensitive reduction semantics for a lambmda-calculus with explicit substitutions and we show that the functional implementation of this small-step semantics mechanically corresponds to that of the abstract machine for Core Scheme presented by Clinger at PLDI'98, including fir...

  1. Quenching of excited uranyl ion during its photochemical reduction with triphenyl-phosphine : Part IV - effect of heterocyclic molecules

    International Nuclear Information System (INIS)

    Sidhu, M.S.; Bhatia, P.V.K.

    1994-01-01

    The presence of heterocyclic compounds triggers off a competition between photophysical and photochemical annihilation of excited uranyl ion during its photochemical reduction with triphenylphosphine. This competition is used to measure Stern-Volmer constant using UV visible spectrophotometer for quenching the uranyl ion luminescence with a number of heterocyclic molecules viz., pyridine, thiophene bipyridyl, tetrahydrofuran and piperidine. (author). 7 refs., 2 figs., 1 tab

  2. Understanding the effectiveness of precursor reductions in lowering 8-hr ozone concentrations--Part II. The eastern United States.

    Science.gov (United States)

    Reynolds, Steven D; Blanchard, Charles L; Ziman, Stephen D

    2004-11-01

    Analyses of ozone (O3) measurements in conjunction with photochemical modeling were used to assess the feasibility of attaining the federal 8-hr O3 standard in the eastern United States. Various combinations of volatile organic compound (VOC) and oxides of nitrogen (NOx) emission reductions were effective in lowering modeled peak 1-hr O3 concentrations. VOC emissions reductions alone had only a modest impact on modeled peak 8-hr O3 concentrations. Anthropogenic NOx emissions reductions of 46-86% of 1996 base case values were needed to reach the level of the 8-hr standard in some areas. As NOx emissions are reduced, O3 production efficiency increases, which accounts for the less than proportional response of calculated 8-hr O3 levels. Such increases in O3 production efficiency also were noted in previous modeling work for central California. O3 production in some urban core areas, such as New York City and Chicago, IL, was found to be VOC-limited. In these areas, moderate NOx emissions reductions may be accompanied by increases in peak 8-hr O3 levels. The findings help to explain differences in historical trends in 1- and 8-hr O3 levels and have serious implications for the feasibility of attaining the 8-hr O3 standard in several areas of the eastern United States.

  3. The Systemic Products as a Source of Competitive Advantage on Healthcare Sector Example. Part II

    Directory of Open Access Journals (Sweden)

    Izabela SZTANGRET

    2015-12-01

    Full Text Available In the healthcare sector, different healthcare providers, such as home care, primary care, pharmacies and hospital clinics but also a financial institution, collaborate in order to increase values for patients, such as better health state, more complex services, high quality of services, and increased feeling of safety. By creating a value, flexible networks health care providers and additional actors create value through collaboration. The purpose of this article is to identify the specific character of systemic healthcare product, created in synergy relations of medical enntities in the area of new way of meeting customers’ needs. Critical analysis of literature in the field of studied category is conducted in the article; furthermore qualitative method of empirical studies (case study and quantitative (online questionnaire is applied for practical illustration of described processes and phenomena. The article is a second part of the stud.

  4. Renewable energy sources usage as a part of the Matsalu wetland management

    International Nuclear Information System (INIS)

    Lotman, Aleksei

    2000-01-01

    Among management objectives of Matsalu wetland the need to harvest some of the naturally growing biomass as a means to keep the wetland communities open and diverse is a priority. At present part of the hay is used for animal fodder and small fraction of reed for roofing. However both uses do not create sufficient demand for biomass. The surplus is apparently large enough to cover totally local demand for heating but the technical solutions for its use are not very clear yet. The reed-beds over two thousand hectares and their average production exceeds ten tons of dry mass per year. Hay-meadows exceed four thousand hectares, of which about two thousand are currently in use. Average yield is about two tons per hectare. Large-scale of wetland's bio fuel resource would contribute to nature conservation objectives for the wetland, create new jobs in the area and reduce air pollution. (author)

  5. 41 CFR 304-3.16 - What must I submit to my agency for reimbursement when a non-Federal source pays all or part of...

    Science.gov (United States)

    2010-07-01

    ... agency for reimbursement when a non-Federal source pays all or part of my travel expenses to attend a meeting? 304-3.16 Section 304-3.16 Public Contracts and Property Management Federal Travel Regulation... submit to my agency for reimbursement when a non-Federal source pays all or part of my travel expenses to...

  6. Development of a new MT system using the commercial power line as a source (Part 3)

    Energy Technology Data Exchange (ETDEWEB)

    Tsubota, Koji; Noritake, Kazumitsu; Miyata, Hatsuho; Sakuma, Hideki; Saito, Akira

    1988-10-01

    PLMT method is an electromagnetic induction method which uses a commercial power line as a source of electomagnetic energy, and enables accurate measurement in short periods. A numeric calculation example of the effect of distance from a power line as well as the results of actual measurements carried out in the Sekiret mining area (Niger) and Kushikino area, Kagoshima Prefecture are reported. Possibility of estimating average ground resistivity by numerical calculation is demonstrated using the electric field and magnetic field generated by power lines. In the measurement in the Sekiret mining area, Niger, north-south electric field and east-west magnetic field were measured from directly under the power line to the distance of 20 km. The relation of the amplitudes of electric field and magnetic field with the distance is shown. The theoretic curve of 0.02 (mho/m) conductivity agreed well with the value mesured in the area about 1 km from the power line. In the measurement at Kushikino area, the value agrees well with the theoretical curve of 0.01 conductivity, whose average resistivity is considered to be about 100 {Omega}m. 6 references, 11 figures.

  7. EFFECTIVNESS OF TARGET ANTIMICROBIAL THERAPY OF SEVERE CHRONIC PERIODONTITIS PART I: REDUCTION OF GINGIVAL INFLAMATION AND ACTIVE PERIODONTAL DISEASE SITES

    Directory of Open Access Journals (Sweden)

    Kamen Kotsilkov

    2010-10-01

    Full Text Available The correlation between recurrent bleeding on probing and the progression of periodontal destruction is suggested in many studies. One of the main goals of the periodontal treatment is the achievement of good control of the gingival inflammation and the reduction of the active periodontal sites.Aim: Evaluation of the effectiveness of treatment of severe chronic periodontitis with additional target antibiotic administration in comparison with the therapy with adjunctive antimicrobial combination amoxicillin + metronidazole and conventional mechanical periodontal treatment regarding the achieved control of the gingival inflammation and BoP.Results: Significant reduction of the gingival bleeding and the BoP is achieved in all groups. In the group with target antibiotic administration the final mean values of the GB (gingival bleeding and BoP (bleeding on probing are the lowest and could suggest a low risk for progression of the periodontal disease.

  8. Bioactivity of Nonedible Parts of Punica granatum L.: A Potential Source of Functional Ingredients

    Directory of Open Access Journals (Sweden)

    Nawraj Rummun

    2013-01-01

    Full Text Available Punica granatum L. has a long standing culinary and medicinal traditional use in Mauritius. This prompted a comparative study to determine the bioefficacy of the flower, peel, leaf, stem, and seed extracts of the Mauritian P. granatum. The flower and peel extracts resulting from organic solvent extraction exhibited strong antioxidant activities which correlated with the high levels of total phenolics, flavonoids, and proanthocyanidins. The peel extract had the most potent scavenging capacity reflected by high Trolox equivalent antioxidant capacity value ( μmol/g air dry weight, very low IC50 values for hypochlorous acid ( mg air dry weight/mL, and hydroxyl radicals scavenging ( mg air dry weight/mL. Peel extracts also significantly inhibited S. mutans (, S. mitis (, and L. acidophilus ( growth compared to ciprofloxacin. The flower extract exhibited high ferric reducing, nitric oxide scavenging, and iron (II ions chelation and significantly inhibited microsomal lipid peroxidation. Furthermore, it showed a dose-dependent inhibition of xanthine oxidase with an IC50 value of  mg air dry weight/mL. This study showed that nonedible parts of cultivated pomegranates, that are generally discarded, are bioactive in multiassay systems thereby suggesting their potential use as natural prophylactics and in food applications.

  9. Bioactivity of Nonedible Parts of Punica granatum L.: A Potential Source of Functional Ingredients

    Science.gov (United States)

    Somanah, Jhoti; Ramsaha, Srishti; Bahorun, Theeshan; Neergheen-Bhujun, Vidushi S.

    2013-01-01

    Punica granatum L. has a long standing culinary and medicinal traditional use in Mauritius. This prompted a comparative study to determine the bioefficacy of the flower, peel, leaf, stem, and seed extracts of the Mauritian P. granatum. The flower and peel extracts resulting from organic solvent extraction exhibited strong antioxidant activities which correlated with the high levels of total phenolics, flavonoids, and proanthocyanidins. The peel extract had the most potent scavenging capacity reflected by high Trolox equivalent antioxidant capacity value (5206.01 ± 578.48 μmol/g air dry weight), very low IC50 values for hypochlorous acid (0.004 ± 0.001 mg air dry weight/mL), and hydroxyl radicals scavenging (0.111 ± 0.001 mg air dry weight/mL). Peel extracts also significantly inhibited S. mutans (P < 0.001), S. mitis (P < 0.001), and L. acidophilus (P < 0.05) growth compared to ciprofloxacin. The flower extract exhibited high ferric reducing, nitric oxide scavenging, and iron (II) ions chelation and significantly inhibited microsomal lipid peroxidation. Furthermore, it showed a dose-dependent inhibition of xanthine oxidase with an IC50 value of 0.058 ± 0.011 mg air dry weight/mL. This study showed that nonedible parts of cultivated pomegranates, that are generally discarded, are bioactive in multiassay systems thereby suggesting their potential use as natural prophylactics and in food applications. PMID:26904607

  10. A two-microphone noise reduction system for cochlear implant users with nearby microphones. Part II: Performance Evaluation

    OpenAIRE

    Kompis, Martin; Bertram, Matthias; Senn, Pascal; Müller, Joachim; Pelizzone, Marco; Häusler, Rudolf

    2008-01-01

    Users of cochlear implants (auditory aids, which stimulate the auditory nerve electrically at the inner ear) often suffer from poor speech understanding in noise. We evaluate a small (intermicrophone distance 7 mm) and computationally inexpensive adaptive noise reduction system suitable for behind-the-ear cochlear implant speech processors. The system is evaluated in simulated and real, anechoic and reverberant environments. Results from simulations show improvements of 3.4 to 9.3 dB in signa...

  11. Towards Compatible and Interderivable Semantic Specifications for the Scheme Programming Language, Part II: Reduction Semantics and Abstract Machines

    DEFF Research Database (Denmark)

    Biernacka, Malgorzata; Danvy, Olivier

    2008-01-01

    We present a context-sensitive reduction semantics for a lambda-calculus with explicit substitutions and store and we show that the functional implementation of this small-step semantics mechanically corresponds to that of an abstract machine. This abstract machine is very close to the abstract m...... machine for Core Scheme presented by Clinger at PLDI'98. This lambda-calculus with explicit substitutions and store therefore aptly accounts for Core Scheme....

  12. sources

    Directory of Open Access Journals (Sweden)

    Shu-Yin Chiang

    2002-01-01

    Full Text Available In this paper, we study the simplified models of the ATM (Asynchronous Transfer Mode multiplexer network with Bernoulli random traffic sources. Based on the model, the performance measures are analyzed by the different output service schemes.

  13. Reduction-oxidation Enabled Glass-ceramics to Stainless Steel Bonding Part I: screening of doping oxidants

    Energy Technology Data Exchange (ETDEWEB)

    Dai, Steve Xunhu [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-09-01

    Lithium silicate-based glass-ceramics with high coefficients of thermal expansion, designed to form matched hermetic seals in 304L stainless steel housing, show little evidence of interfacial chemical bonding, despite extensive inter-diffusion at the glass-ceramic-stainless steel (GC-SS) interface. A series of glass-ceramic compositions modified with a variety of oxidants, AgO, FeO, NiO, PbO, SnO, CuO, CoO, MoO3 and WO3, are examined for the feasibility of forming bonding oxides through reduction-oxidation (redox) at the GC-SS interface. The oxidants were selected according to their Gibbs free energy to allow for oxidation of Cr/Mn/Si from stainless steel, and yet to prevent a reduction of P2O5 in the glass-ceramic where the P2O5 is to form Li3PO4 nuclei for growth of high expansion crystalline SiO2 phases. Other than the CuO and CoO modified glass-ceramics, bonding from interfacial redox reactions were not achieved in the modified glass-ceramics, either because of poor wetting on the stainless steel or a reduction of the oxidants at the surface of glass-ceramic specimens rather than the GC-SS interface.

  14. Oxygenated gasoline release in the unsaturated zone - Part 1: Source zone behavior.

    Science.gov (United States)

    Freitas, Juliana G; Barker, James F

    2011-11-01

    Oxygenates present in gasoline, such as ethanol and MTBE, are a concern in subsurface contamination related to accidental spills. While gasoline hydrocarbon compounds have low solubility, MTBE and ethanol are more soluble, ethanol being completely miscible with water. Consequently, their fate in the subsurface is likely to differ from that of gasoline. To evaluate the fate of gasoline containing oxygenates following a release in the unsaturated zone shielded from rainfall/recharge, a controlled field test was performed at Canadian Forces Base Borden, in Ontario. 200L of a mixture composed of gasoline with 10% ethanol and 4.5% MTBE was released in the unsaturated zone, into a trench 20cm deep, about 32cm above the water table. Based on soil cores, most of the ethanol was retained in the source, above the capillary fringe, and remained there for more than 100 days. Ethanol partitioned from the gasoline to the unsaturated pore-water and was retained, despite the thin unsaturated zone at the site (~35cm from the top of the capillary fringe to ground surface). Due to its lower solubility, most of the MTBE remained within the NAPL as it infiltrated deeper into the unsaturated zone and accumulated with the gasoline on top of the depressed capillary fringe. Only minor changes in the distribution of ethanol were noted following oscillations in the water table. Two methods to estimate the capacity of the unsaturated zone to retain ethanol are explored. It is clear that conceptual models for sites impacted by ethanol-fuels must consider the unsaturated zone. Copyright © 2011 Elsevier B.V. All rights reserved.

  15. Hydrogenated graphenes by birch reduction: influence of electron and proton sources on hydrogenation efficiency, magnetism, and electrochemistry

    Czech Academy of Sciences Publication Activity Database

    Eng, A.Y.S.; Sofer, Z.; Huber, Š.; Bouša, D.; Maryško, Miroslav; Pumera, M.

    2015-01-01

    Roč. 21, č. 7 (2015), 16828-16838 ISSN 0947-6539 Institutional support: RVO:68378271 Keywords : hydrogenated graphenes * birch reduction * magnetism * electrochemistry * hydrogenation efficiency Subject RIV: CA - Inorganic Chemistry Impact factor: 5.771, year: 2015

  16. Global Emissions of Nitrous Oxide: Key Source Sectors, their Future Activities and Technical Opportunities for Emission Reduction

    Science.gov (United States)

    Winiwarter, W.; Höglund-Isaksson, L.; Klimont, Z.; Schöpp, W.; Amann, M.

    2017-12-01

    Nitrous oxide originates primarily from natural biogeochemical processes, but its atmospheric concentrations have been strongly affected by human activities. According to IPCC, it is the third largest contributor to the anthropogenic greenhouse gas emissions (after carbon dioxide and methane). Deep decarbonization scenarios, which are able to constrain global temperature increase within 1.5°C, require strategies to cut methane and nitrous oxide emissions on top of phasing out carbon dioxide emissions. Employing the Greenhouse gas and Air pollution INteractions and Synergies (GAINS) model, we have estimated global emissions of nitrous oxide until 2050. Using explicitly defined emission reduction technologies we demonstrate that, by 2030, about 26% ± 9% of the emissions can be avoided assuming full implementation of currently existing reduction technologies. Nearly a quarter of this mitigation can be achieved at marginal costs lower than 10 Euro/t CO2-eq with the chemical industry sector offering important reductions. Overall, the largest emitter of nitrous oxide, agriculture, also provides the largest emission abatement potentials. Emission reduction may be achieved by precision farming methods (variable rate technology) as well as by agrochemistry (nitrification inhibitors). Regionally, the largest emission reductions are achievable where intensive agriculture and industry are prevalent (production and application of mineral fertilizers): Centrally Planned Asia including China, North and Latin America, and South Asia including India. Further deep cuts in nitrous oxide emissions will require extending reduction efforts beyond strictly technological solutions, i.e., considering behavioral changes, including widespread adoption of "healthy diets" minimizing excess protein consumption.

  17. A new laser vibrometry-based 2D selective intensity method for source identification in reverberant fields: part II. Application to an aircraft cabin

    International Nuclear Information System (INIS)

    Revel, G M; Martarelli, M; Chiariotti, P

    2010-01-01

    The selective intensity technique is a powerful tool for the localization of acoustic sources and for the identification of the structural contribution to the acoustic emission. In practice, the selective intensity method is based on simultaneous measurements of acoustic intensity, by means of a couple of matched microphones, and structural vibration of the emitting object. In this paper high spatial density multi-point vibration data, acquired by using a scanning laser Doppler vibrometer, have been used for the first time. Therefore, by applying the selective intensity algorithm, the contribution of a large number of structural sources to the acoustic field radiated by the vibrating object can be estimated. The selective intensity represents the distribution of the acoustic monopole sources on the emitting surface, as if each monopole acted separately from the others. This innovative selective intensity approach can be very helpful when the measurement is performed on large panels in highly reverberating environments, such as aircraft cabins. In this case the separation of the direct acoustic field (radiated by the vibrating panels of the fuselage) and the reverberant one is difficult by traditional techniques. The work shown in this paper is the application of part of the results of the European project CREDO (Cabin Noise Reduction by Experimental and Numerical Design Optimization) carried out within the framework of the EU. Therefore the aim of this paper is to illustrate a real application of the method to the interior acoustic characterization of an Alenia Aeronautica ATR42 ground test facility, Alenia Aeronautica being a partner of the CREDO project

  18. Indigenous instrumentation for mass spectrometry: Part II - development of plasma source mass spectrometers. PD-5-3

    International Nuclear Information System (INIS)

    Nataraju, V.

    2007-01-01

    The growing demands from analytical community, for a precise isotope ratio and ultra trace concentration measurements, has lead to significant improvement in mass spectrometer instrumentation development with respect to sensitivity, detection limits, precision and accuracy. Among the many analytical techniques available, plasma source mass spectrometers like Inductively Coupled Plasma Mass Spectrometry (ICPMS), multi collector (MC) ICPMS and Glow Discharge Mass Spectrometry (GDMS), have matured into reliable tools for the above applications. Where as ICPMS is by far the most successful method for aqueous solutions, GDMS is being applied for bulk and impurity analysis of conducting as well non-conducting solids. VPID, BARC has been developing mass spectrometers for different inorganic applications of DAE users. Over the years expertise has been developed in all the aspects of mass spectrometry instrumentation. Part 1 of this indigenous instrumentation on mass spectrometry gives details of magnetic sector instruments with either EI or TI source for isotopic ratio analysis. The present paper is a continuation of that on plasma source and quadrupole mass spectrometers. This paper covers i) ICP-QMS, ii) MC-ICPMS, iii) GDMS and iv) QMS

  19. Using hydrogeology to identify the source of groundwater to Montezuma Well, a natural spring in central Arizona: part 1

    Science.gov (United States)

    Johnson, Raymond H.; DeWitt, Ed H.; Arnold, L. Rick

    2012-01-01

    Montezuma Well is a natural spring located within a “sinkhole” in the desert environment of the Verde Valley in Central Arizona. It is managed by the National Park Service as part of Montezuma Castle National Monument. Because of increasing development of groundwater in the area, this research was undertaken to better understand the sources of groundwater to Montezuma Well. The use of well logs and geophysics provides details on the geology in the area around Montezuma Well. This includes characterizing the extent and position of a basalt dike that intruded a deep fracture zone. This low permeability barrier forces groundwater to the surface at the Montezuma Well “pool” with sufficient velocity to entrain sand-sized particles from underlying bedrock. Permeable fractures along and above the basalt dike provide conduits that carry deep sourced carbon dioxide to the surface, which can dissolve carbonate minerals along the transport path in response to the added carbon dioxide. At the ground surface, CO2 degasses, depositing travertine. Geologic cross sections, rock geochemistry, and semi-quantitative groundwater flow modeling provide a hydrogeologic framework that indicates groundwater flow through a karstic limestone at depth (Redwall Limestone) as the most significant source of groundwater to Montezuma Well. Additional groundwater flow from the overlying formations (Verde Formation and Permian Sandstones) is a possibility, but significant flow from these units is not indicated.

  20. Assessment of GHG Emission Reduction Potential from Source-separated Organic Waste (SOW) Management: Case Study in a Higher Educational Institution in Malaysia

    International Nuclear Information System (INIS)

    Ng, C.G.; Sumiani Yusoff

    2015-01-01

    In Malaysia, the greenhouse gases (GHGs) emissions reduction via composting of source-separated organic waste (SOW) in municipal solid waste (MSW) has not been assessed. Assessment of GHG emissions reduction via composting of SOW is important as environmental impacts from waste management are waste-specific and local-specific. The study presents the case study for potential carbon reduction via composting of SOW in University of Malaya (UM). In this study, a series of calculations were used to evaluate the GHG emission of different SOW management scenarios. The calculations based on IPCC calculation methods (AM0025) include GHGs emissions from land filling, fuel consumption in transportation and SOW composting activity. The methods were applied to assess the GHG emissions from five alternative SOW management scenarios in UM. From the baseline scenario (S0), a total of 1,636.18 tCO2e was generated. In conjunction with target of 22 % recycling rate, as shown in S1, 14 % reduction in potential GHG emission can be achieved. The carbon reduction can be further enhanced by increasing the SOW composting capacity. The net GHG emission for S1, S2, S3 and S4 were 1,399.52, 1,161.29, 857.70 and 1,060.48 tCO2e, respectively. In general, waste diversion for composting proved a significant net GHG emission reduction as shown in S3 (47 %), S4 (35 %) and S2 (29 %). Despite the emission due to direct on-site activity, the significant reduction in methane generation at landfill has reduced the net GHG emission. The emission source of each scenario was studied and analysed. (author)

  1. Reductions in the Cardiac Transient Outward K+ Current Ito Caused by Chronic β-Adrenergic Receptor Stimulation Are Partly Rescued by Inhibition of Nuclear Factor κB.

    Science.gov (United States)

    Panama, Brian K; Korogyi, Adam S; Aschar-Sobbi, Roozbeh; Oh, Yena; Gray, Charles B B; Gang, Hongying; Brown, Joan Heller; Kirshenbaum, Lorrie A; Backx, Peter H

    2016-02-19

    The fast transient outward potassium current (Ito,f) plays a critical role in the electrical and contractile properties of the myocardium. Ito,f channels are formed by the co-assembly of the pore-forming α-subunits, Kv4.2 and Kv4.3, together with the accessory β-subunit KChIP2. Reductions of Ito,f are common in the diseased heart, which is also associated with enhanced stimulation of β-adrenergic receptors (β-ARs). We used cultured neonatal rat ventricular myocytes to examine how chronic β-AR stimulation decreases Ito,f. To determine which downstream pathways mediate these Ito,f changes, adenoviral infections were used to inhibit CaMKIIδc, CaMKIIδb, calcineurin, or nuclear factor κB (NF-κB). We observed that chronic β-AR stimulation with isoproterenol (ISO) for 48 h reduced Ito,f along with mRNA expression of all three of its subunits (Kv4.2, Kv4.3, and KChIP2). Inhibiting either CaMKIIδc nor CaMKIIδb did not prevent the ISO-mediated Ito,f reductions, even though CaMKIIδc and CaMKIIδb clearly regulated Ito,f and the mRNA expression of its subunits. Likewise, calcineurin inhibition did not prevent the Ito,f reductions induced by β-AR stimulation despite strongly modulating Ito,f and subunit mRNA expression. In contrast, NF-κB inhibition partly rescued the ISO-mediated Ito,f reductions in association with restoration of KChIP2 mRNA expression. Consistent with these observations, KChIP2 promoter activity was reduced by p65 as well as β-AR stimulation. In conclusion, NF-κB, and not CaMKIIδ or calcineurin, partly mediates the Ito,f reductions induced by chronic β-AR stimulation. Both mRNA and KChIP2 promoter data suggest that the ISO-induced Ito,f reductions are, in part, mediated through reduced KChIP2 transcription caused by NF-κB activation. © 2016 by The American Society for Biochemistry and Molecular Biology, Inc.

  2. When probabilistic seismic hazard climbs volcanoes: the Mt. Etna case, Italy - Part 1: Model components for sources parameterization

    Science.gov (United States)

    Azzaro, Raffaele; Barberi, Graziella; D'Amico, Salvatore; Pace, Bruno; Peruzza, Laura; Tuvè, Tiziana

    2017-11-01

    . They can be relevant for the retrofitting of the existing building stock and for driving risk reduction interventions. These analyses do not account for regional M > 6 seismogenic sources which dominate the hazard over long return times (≥ 500 years).

  3. Optimization of filtration for the reduction of lung dose from Rn decay products: Part II--Experimental

    International Nuclear Information System (INIS)

    Curling, C.A.; Rudnick, S.N.; Harrington, D.P.; Moeller, D.W.

    1990-01-01

    Research was performed to determine the validity of a model developed to theoretically predict the optimal characteristics of a recirculating filter system for minimizing the lung dose to a person breathing airborne Rn progeny. Four designs, each with different filter thicknesses, solidities, and fiber diameters, were tested to evaluate the accuracy of the model over a range of parameters. Increasing thicknesses were then tested for the most effective filter design to provide a more definitive comparison of experimental data and model predictions for this key parameter. The experimental data supported the conclusion that the most effective design was a thin filter of low solidity composed of coarse fibers. Although the maximum reduction in the dose-equivalent rate observed in these experiments was 50%, this was largely due to constraints on the experimental arrangements. With properly constructed filter units, much better removal efficiencies can undoubtedly be achieved

  4. Two-dimensional analytical solutions for chemical transport in aquifers. Part 1. Simplified solutions for sources with constant concentration. Part 2. Exact solutions for sources with constant flux rate

    International Nuclear Information System (INIS)

    Shan, C.; Javandel, I.

    1996-05-01

    Analytical solutions are developed for modeling solute transport in a vertical section of a homogeneous aquifer. Part 1 of the series presents a simplified analytical solution for cases in which a constant-concentration source is located at the top (or the bottom) of the aquifer. The following transport mechanisms have been considered: advection (in the horizontal direction), transverse dispersion (in the vertical direction), adsorption, and biodegradation. In the simplified solution, however, longitudinal dispersion is assumed to be relatively insignificant with respect to advection, and has been neglected. Example calculations are given to show the movement of the contamination front, the development of concentration profiles, the mass transfer rate, and an application to determine the vertical dispersivity. The analytical solution developed in this study can be a useful tool in designing an appropriate monitoring system and an effective groundwater remediation method

  5. Sampling of illicit drugs for quantitative analysis--part II. Study of particle size and its influence on mass reduction.

    Science.gov (United States)

    Bovens, M; Csesztregi, T; Franc, A; Nagy, J; Dujourdy, L

    2014-01-01

    The basic goal in sampling for the quantitative analysis of illicit drugs is to maintain the average concentration of the drug in the material from its original seized state (the primary sample) all the way through to the analytical sample, where the effect of particle size is most critical. The size of the largest particles of different authentic illicit drug materials, in their original state and after homogenisation, using manual or mechanical procedures, was measured using a microscope with a camera attachment. The comminution methods employed included pestle and mortar (manual) and various ball and knife mills (mechanical). The drugs investigated were amphetamine, heroin, cocaine and herbal cannabis. It was shown that comminution of illicit drug materials using these techniques reduces the nominal particle size from approximately 600 μm down to between 200 and 300 μm. It was demonstrated that the choice of 1 g increments for the primary samples of powdered drugs and cannabis resin, which were used in the heterogeneity part of our study (Part I) was correct for the routine quantitative analysis of illicit seized drugs. For herbal cannabis we found that the appropriate increment size was larger. Based on the results of this study we can generally state that: An analytical sample weight of between 20 and 35 mg of an illicit powdered drug, with an assumed purity of 5% or higher, would be considered appropriate and would generate an RSDsampling in the same region as the RSDanalysis for a typical quantitative method of analysis for the most common, powdered, illicit drugs. For herbal cannabis, with an assumed purity of 1% THC (tetrahydrocannabinol) or higher, an analytical sample weight of approximately 200 mg would be appropriate. In Part III we will pull together our homogeneity studies and particle size investigations and use them to devise sampling plans and sample preparations suitable for the quantitative instrumental analysis of the most common illicit

  6. Photo-illuminated diamond as a solid-state source of solvated electrons in water for nitrogen reduction.

    Science.gov (United States)

    Zhu, Di; Zhang, Linghong; Ruther, Rose E; Hamers, Robert J

    2013-09-01

    The photocatalytic reduction of N₂ to NH₃ is typically hampered by poor binding of N₂ to catalytic materials and by the very high energy of the intermediates involved in this reaction. Solvated electrons directly introduced into the reactant solution can provide an alternative pathway to overcome such limitations. Here we demonstrate that illuminated hydrogen-terminated diamond yields facile electron emission into water, thus inducing reduction of N₂ to NH₃ at ambient temperature and pressure. Transient absorption measurements at 632 nm reveal the presence of solvated electrons adjacent to the diamond after photoexcitation. Experiments using inexpensive synthetic diamond samples and diamond powder show that photocatalytic activity is strongly dependent on the surface termination and correlates with the production of solvated electrons. The use of diamond to eject electrons into a reactant liquid represents a new paradigm for photocatalytic reduction, bringing electrons directly to reactants without requiring molecular adsorption to the surface.

  7. Splint therapy for disc displacement with reduction of the temporomandibular joint. Part I: Modified mandibular splint therapy

    Directory of Open Access Journals (Sweden)

    I-Yueh Huang

    2011-08-01

    Full Text Available The aims of this preliminary study were to present a modified mandibular splint together with a treatment regimen and to evaluate their effects on the treatment of reciprocal joint sounds of the temporomandibular joint (TMJ. The study participants were recruited from 312 consecutive patients in the temporomandibular disorder clinic of a medical center in Taiwan from January 2003 to December 2003. From among these, 59 cases with typical reciprocal clicking were selected for this study. All participants were treated with a modified mandibular splint and then followed up for 6 months. Successful treatment was defined as leading to the disappearance of the joint sounds of TMJ, as described by patients. Based on clinical evaluation, the overall success rate was 71.2% (42/59 with minimal temporary complications. Patients with clicking at less than 3.5 cm of interincisal opening had a success rate of 92.5%, which was higher than the success rate of patients with clicking at a mouth opening of 3.5 cm or more. This study showed that a modified mandibular splint can be used to treat reciprocal clicking of the TMJ effectively and encouraged us to conduct further study on the efficacy of this splint to treat disc displacement with reduction of TMJ using magnetic resonance imaging examination.

  8. Systematic reduction of complex tropospheric chemical mechanisms, Part II: Lumping using a time-scale based approach

    Directory of Open Access Journals (Sweden)

    L. E. Whitehouse

    2004-01-01

    Full Text Available This paper presents a formal method of species lumping that can be applied automatically to intermediate compounds within detailed and complex tropospheric chemical reaction schemes. The method is based on grouping species with reference to their chemical lifetimes and reactivity structures. A method for determining the forward and reverse transformations between individual and lumped compounds is developed. Preliminary application to the Leeds Master Chemical Mechanism (MCMv2.0 has led to the removal of 734 species and 1777 reactions from the scheme, with minimal degradation of accuracy across a wide range of test trajectories relevant to polluted tropospheric conditions. The lumped groups are seen to relate to groups of peroxy acyl nitrates, nitrates, carbonates, oxepins, substituted phenols, oxeacids and peracids with similar lifetimes and reaction rates with OH. In combination with other reduction techniques, such as sensitivity analysis and the application of the quasi-steady state approximation (QSSA, a reduced mechanism has been developed that contains 35% of the number of species and 40% of the number of reactions compared to the full mechanism. This has led to a speed up of a factor of 8 in terms of computer calculation time within box model simulations.

  9. Microgrids project. Part 2. Design of an electrification kit with high content of renewable energy sources in Senegal

    Energy Technology Data Exchange (ETDEWEB)

    Alzola, J.A.; Santos, M. [Robotiker Tecnalia, Parque Tecnologico, Edificio 202, 48170 Zamudio (Spain); Vechiu, I. [ESTIA Recherche Technopole Izarbel, 64210 Bidart (France); Camblong, H. [ESTIA Recherche Technopole Izarbel, 64210 Bidart (France); Electrical Engineering Department, University of the Basque Country (E.U.P.-D), Europa Plaza 1, 20018 Donostia - San Sebastian (Spain); Sall, M. [Centre d' Etudes et de Recherches sur les Energies Renouvelables (UCAD) (Senegal); Sow, G. [Laboratoire des Energies Renouvelables (LER), Ecole Sup. Polytechnique, Dakar (Senegal)

    2009-10-15

    Senegal is one of the less developed countries in the world (position 158 in a list of 174 countries). 85% of its rural population does not have access to electricity and there's no doubt that this is an important barrier for socio-economic development. In this context, the project Microgrids aims at contributing to solve this problem. This project is part of the Intelligent Energy - Europe Programme supported by the European Commission. Its objective is the promotion and dissemination of the use of micro-grids with high content of Renewable Energy Sources (RES) for the electrification of villages far away from the grid in Senegal. One of the results of the project was the analysis of rural electrification needs, which is described in another paper [Camblong H, Sarr J, Niang AT, Curea O, Alzola JA, Sylla EH, Santos M. Microgrids project, part 1: analysis of rural electrification with high content of renewable energy sources in Senegal. Renewable Energy, submitted for publication.]. This paper presents the design of an electrification kit based on the information provided by that analysis [Analyse des besoins locaux pour l'electrification de zones rurales au Senegal. Technical report of Microgrids project; 2007. Available from: http://www.microgrids-eie.com.]. After identifying necessary previous conditions for the sustainability of any electrification project, a methodology is proposed for the design of the electrification kit. This methodology is applied to a typical village and results are extended to differently sized villages in the areas of Thies, Fatick and Kaolack. Economic considerations are also included to establish the relationship between electrification costs and paying capability of the communities. Now the Microgrids' consortium hopes to set-up a new project to apply the designed kit on some rural non-electrified villages. (author)

  10. Flood risk reduction and flow buffering as ecosystem services - Part 2: Land use and rainfall intensity effects in Southeast Asia

    Science.gov (United States)

    van Noordwijk, Meine; Tanika, Lisa; Lusiana, Betha

    2017-05-01

    Watersheds buffer the temporal pattern of river flow relative to the temporal pattern of rainfall. This ecosystem service is inherent to geology and climate, but buffering also responds to human use and misuse of the landscape. Buffering can be part of management feedback loops if salient, credible and legitimate indicators are used. The flow persistence parameter Fp in a parsimonious recursive model of river flow (Part 1, van Noordwijk et al., 2017) couples the transmission of extreme rainfall events (1 - Fp), to the annual base-flow fraction of a watershed (Fp). Here we compare Fp estimates from four meso-scale watersheds in Indonesia (Cidanau, Way Besai and Bialo) and Thailand (Mae Chaem), with varying climate, geology and land cover history, at a decadal timescale. The likely response in each of these four to variation in rainfall properties (including the maximum hourly rainfall intensity) and land cover (comparing scenarios with either more or less forest and tree cover than the current situation) was explored through a basic daily water-balance model, GenRiver. This model was calibrated for each site on existing data, before being used for alternative land cover and rainfall parameter settings. In both data and model runs, the wet-season (3-monthly) Fp values were consistently lower than dry-season values for all four sites. Across the four catchments Fp values decreased with increasing annual rainfall, but specific aspects of watersheds, such as the riparian swamp (peat soils) in Cidanau reduced effects of land use change in the upper watershed. Increasing the mean rainfall intensity (at constant monthly totals for rainfall) around the values considered typical for each landscape was predicted to cause a decrease in Fp values by between 0.047 (Bialo) and 0.261 (Mae Chaem). Sensitivity of Fp to changes in land use change plus changes in rainfall intensity depends on other characteristics of the watersheds, and generalisations made on the basis of one or two

  11. Resource analysis of the Chinese society 1980-2002 based on exergy-Part 2: Renewable energy sources and forest

    International Nuclear Information System (INIS)

    Chen, B.; Chen, G.Q.

    2007-01-01

    This second part is the continuation of the first part on fossil fuels and energy minerals. The major renewable energy sources and forest products entering the Chinese society from 1980 to 2002, including sunlight, wind power, tidal power, wave power, geothermal power and heating, biomass, hydroelectric resource and forestry products, are calculated and analyzed in detail in this paper. The solar exergy inputs from solar photovoltaics and solar collectors, including water heater, solar oven and solar building, are calculated and discussed. The development of the wind power plant is presented. Major tidal power plants, which are still working, are addressed. Wave power devices and plants are introduced. Geothermal resources, mainly for power generation and heating, associated with distribution, are depicted. The utilization of biomass, embracing firewood, straw and biogas, which served as the main obtainable local resources for private consumption and production in the rural areas, is illustrated. Development of hydroelectric resources as complement to scarce fossil fuels is represented, of which the small hydropower project adapted for rural areas is emphasized. Finally, forest products from timber forest and economic forest are presented, with the forestation, reproducing, tending areas and sum of odd forestation trees being manifested

  12. Green house gas emissions in German agriculture. Sources and technical reduction capacities under special consideration of biogas; Treibhausgas-Emissionen in der deutschen Landwirtschaft. Herkunft und technische Minderungspotenziale unter besonderer Beruecksichtigung von Biogas

    Energy Technology Data Exchange (ETDEWEB)

    Wegener, Jens-Karl

    2006-12-15

    This monograph is concerned with different aspects of green house gas (GHG) emissions in agriculture. The first part summarizes the total amount of GHG emissions and analyses them regarding their composition. A differentiation is made between the emissions which are already linked to agriculture (source group agriculture: ''digestion'', ''manure-management'' and ''agricultural soils'') within the ''National Report on GHG Emissions'' and those which can be counted primarily in addition to agriculture (''energy'' and ''land use and land use change''). Depending on which database is used, agriculture is participating in emitting green house gases with 6.3% or 11.1% of total German GHG emissions in 2004. This means that agriculture is an important polluter. The development of GHG emissions in agriculture compared to the year 1990 is -18.5% for the source group agriculture. This means that the source group has reduced more emissions than the average (-17.5%) over all domains published within the National Report. Regarding the sources ''energy'' and ''land use and land use change'' in addition emission reduction is -16.4% in the same period and thus worse than the average. Moreover, realized emission reductions are predominantly based on structural changes, less on systematical measures. This fact raises the question how agriculture can make a contribution to the reduction of GHG emissions in future particularly with regard to higher aims in climate politics. For this reason the second part of the monograph identifies capacities for the reduction of GHG emissions by using available agricultural biomass for energetic purposes. Due to the heterogeneity of biomass and the variety of its possible products, a lot of technical processes concerning the conversion of biomass into energy exist in practice. Since all of

  13. More gas, less coal, and less CO2? Unilateral CO2 reduction policy with more than one carbon energy source

    DEFF Research Database (Denmark)

    Daubanes, Julien Xavier; Henriet, Fanny; Schubert, Katheline

    -productive, ultimately increasing world emissions. Thus, we establish testable conditions as to whether a governmental emission-reduction commitment warrants the exploitation of gas, and whether such a strategy increases global emissions. We also characterize the extent to which this unilateral policy makes the rest...... of the world’s emission commitments more difficult to meet. Finally, we apply our results to the case of the US....

  14. Reduction of plasma density in the Helicity Injected Torus with Steady Inductance experiment by using a helicon pre-ionization source

    International Nuclear Information System (INIS)

    Hossack, Aaron C.; Jarboe, Thomas R.; Victor, Brian S.; Firman, Taylor; Prager, James R.; Ziemba, Timothy; Wrobel, Jonathan S.

    2013-01-01

    A helicon based pre-ionization source has been developed and installed on the Helicity Injected Torus with Steady Inductance (HIT-SI) spheromak. The source initiates plasma breakdown by injecting impurity-free, unmagnetized plasma into the HIT-SI confinement volume. Typical helium spheromaks have electron density reduced from (2–3) × 10 19 m −3 to 1 × 10 19 m −3 . Deuterium spheromak formation is possible with density as low as 2 × 10 18 m −3 . The source also enables HIT-SI to be operated with only one helicity injector at injector frequencies above 14.5 kHz. A theory explaining the physical mechanism driving the reduction of breakdown density is presented

  15. Reduction of plasma density in the Helicity Injected Torus with Steady Inductance experiment by using a helicon pre-ionization source

    Energy Technology Data Exchange (ETDEWEB)

    Hossack, Aaron C.; Jarboe, Thomas R.; Victor, Brian S. [Department of Aeronautics and Astronautics, University of Washington, Seattle, Washington 98195 (United States); Firman, Taylor; Prager, James R.; Ziemba, Timothy [Eagle Harbor Technologies, Inc., 119 W. Denny Way, Suite 210, Seattle, Washington 98119 (United States); Wrobel, Jonathan S. [979B West Moorhead Circle, Boulder, Colorado 80305 (United States)

    2013-10-15

    A helicon based pre-ionization source has been developed and installed on the Helicity Injected Torus with Steady Inductance (HIT-SI) spheromak. The source initiates plasma breakdown by injecting impurity-free, unmagnetized plasma into the HIT-SI confinement volume. Typical helium spheromaks have electron density reduced from (2–3) × 10{sup 19} m{sup −3} to 1 × 10{sup 19} m{sup −3}. Deuterium spheromak formation is possible with density as low as 2 × 10{sup 18} m{sup −3}. The source also enables HIT-SI to be operated with only one helicity injector at injector frequencies above 14.5 kHz. A theory explaining the physical mechanism driving the reduction of breakdown density is presented.

  16. Source zone remediation by ZVI-clay soil-mixing: Reduction of tetrachloroethene mass and mass discharge at a Danish DNAPL site

    DEFF Research Database (Denmark)

    Fjordbøge, Annika Sidelmann; Lange, Ida Vedel; Binning, Philip John

    2012-01-01

    The presence of chlorinated solvent source zones in the subsurface pose a continuous threat to groundwater quality. The remediation of Dense Non-Aqueous Phase Liquid (DNAPL) sites is especially challenging and the development of innovative remediation technologies is needed. Zero-valent iron (ZVI......) technologies have proven effective for remediation of chlorinated compounds. ZVI-Clay soil-mixing is a new remediation technology, which combines abiotic degradation (via ZVI addition) and immobilization (via soil-mixing and clay addition), whereby a great potential for reduction of both contaminant mass....... The concentrations of chlorinated ethenes were monitored via soil sampling at the source zone and groundwater sampling at a control plane with multilevel samplers covering the entire contaminated plume down-gradient (3 m) of the source zone. The results showed a significant mass depletion of PCE (2-3 orders...

  17. Development of dynamic loudspeakers modified as incident pressure sources for noise reduction in a double panel structure

    NARCIS (Netherlands)

    Ho, J.; Berkhoff, Arthur P.; Crocker, Malcolm J.; Pawelczyk, Marek; Paosawatyanyong, Boonchoat

    2013-01-01

    This paper presents a modified loudspeaker source for decentralized feedback cavity control in a double panel structure to reduce the noise transmission. The double panel structure con-sists of two panels with air in between and offers the advantages of low weight, low sound transmission at high

  18. Containment at the Source during Waste Volume Reduction of Large Radioactive Components Using Oxylance High-Temperature Cutting Equipment - 13595

    International Nuclear Information System (INIS)

    Keeney, G. Neil

    2013-01-01

    As a waste-volume reduction and management technique, highly contaminated Control Element Drive Mechanism (CEDM) housings were severed from the Reactor Pressure Vessel Head (RPVH) inside the San Onofre Unit 2 primary containment utilizing Oxylance high-temperature cutting equipment and techniques. Presented are relevant data concerning: - Radiological profiles of the RPVH and individual CEDMs; - Design overviews of the engineering controls and the specialized confinement housings; - Utilization of specialized shielding; - Observations of apparent metallurgical-contamination coalescence phenomena at high temperatures resulting in positive control over loose-surface contamination conditions; - General results of radiological and industrial hygiene air sampling and monitoring; - Collective dose and personnel contamination event statistics; - Lessons learned. (author)

  19. Containment at the Source during Waste Volume Reduction of Large Radioactive Components Using Oxylance High-Temperature Cutting Equipment - 13595

    Energy Technology Data Exchange (ETDEWEB)

    Keeney, G. Neil [Health Physicist, HazMat CATS, LLC (United States)

    2013-07-01

    As a waste-volume reduction and management technique, highly contaminated Control Element Drive Mechanism (CEDM) housings were severed from the Reactor Pressure Vessel Head (RPVH) inside the San Onofre Unit 2 primary containment utilizing Oxylance high-temperature cutting equipment and techniques. Presented are relevant data concerning: - Radiological profiles of the RPVH and individual CEDMs; - Design overviews of the engineering controls and the specialized confinement housings; - Utilization of specialized shielding; - Observations of apparent metallurgical-contamination coalescence phenomena at high temperatures resulting in positive control over loose-surface contamination conditions; - General results of radiological and industrial hygiene air sampling and monitoring; - Collective dose and personnel contamination event statistics; - Lessons learned. (author)

  20. Technical Guidance Manual: Contaminant Flux Reduction Barriers for Managing Difficult-to-Treat Source Zones in Unconsolidated Media

    Science.gov (United States)

    2017-06-20

    zone, the site must be:  Comprised of unconsolidated material (gravel, sand, silt, clay )  Have access around the source zone to building the...lower low permeability unit such as a clay to prevent up flow  For accessing the lower cost silica gel grouting technology, the hydraulic...hydraulic conductivity with sodium silicate grout.” (page 4-20).  Viscosities of typical grouts (Powers Figure 22.10)  Typical properties of Sodium

  1. 49 CFR Appendix B to Part 564 - Information To Be Submitted for Long Life Replaceable Light Sources of Limited Definition

    Science.gov (United States)

    2010-10-01

    ...—Information To Be Submitted for Long Life Replaceable Light Sources of Limited Definition I. Filament or... Source that Operates With a Ballast and Rated Life of the Light Source/Ballast Combination. A. Maximum power (in watts). B. Luminous Flux (in lumens). C. Rated laboratory life of the light source/ballast...

  2. Salinity sources of Kefar Uriya wells in the Judea Group aquifer of Israel. Part 1—conceptual hydrogeological model

    Science.gov (United States)

    Avisar, D.; Rosenthal, E.; Flexer, A.; Shulman, H.; Ben-Avraham, Z.; Guttman, J.

    2003-01-01

    In the Yarkon-Taninim groundwater basin, the karstic Judea Group aquifer contains groundwater of high quality. However, in the western wells of the Kefar Uriya area located in the foothills of the Judea Mountains, brackish groundwater was locally encountered. The salinity of this water is caused presumably by two end members designated as the 'Hazerim' and 'Lakhish' water types. The Hazerim type represents surface water percolating through a highly fractured thin chalky limestone formation overlying the Judea Group aquifer. The salinity of the water derives conjointly from several sources such as leachates from rendzina and grumosols, dissolution of caliche crusts which contain evaporites and of rock debris from the surrounding formations. This surface water percolates downwards into the aquifer through a funnel- or chimney-like mechanism. This local salinization mechanism supercedes another regional process caused by the Lakhish waters. These are essentially diluted brines originating from deep formations in the western parts of the Coastal Plain. The study results show that salinization is not caused by the thick chalky beds of the Senonian Mt Scopus Group overlying the Judea Group aquifer, as traditionally considered but prevalently by aqueous leachates from soils and rock debris. The conceptual qualitative hydrogeological model of the salinization as demonstrated in this study, is supported by a quantitative hydrological model presented in another paper in this volume.

  3. Integrated Verification Experiment data collected as part of the Los Alamos National Laboratory's Source Region Program

    Energy Technology Data Exchange (ETDEWEB)

    Whitaker, R.W.; Noel, S.D.

    1992-12-01

    The summary report by Tom Weaver gives the overall background for the series of IVE (Integrated Verification Experiment) experiments including information on the full set of measurements made. This appendix presents details of the infrasound data for the and discusses certain aspects of a few special experiments. Prior to FY90, the emphasis of the Infrasound Program was on underground nuclear test (UGT) detection and yield estimation. During this time the Infrasound Program was a separate program at Los Alamos, and it was suggested to DOE/OAC that a regional infrasound network be established around NTS. The IVE experiments took place in a time frame that allowed simultaneous testing of possible network sites and examination of propagation in different directions. Whenever possible, infrasound stations were combined with seismic stations so that a large number could be efficiently fielded. The regional infrasound network was not pursued by DOE, as world events began to change the direction of verification toward non-proliferation. Starting in FY90 the infrasound activity became part of the Source Region Program which has a goal of understanding how energy is transported from the UGT to a variety of measurement locations.

  4. [Energy sources. Social and environmental impact and societal models: future perspectives. Part 1: General aspects and reflections.].

    Science.gov (United States)

    Delia, Santi; Cannavò, Giuseppe; Parisi, Salvatore; Laganà, Pasqualina

    2009-01-01

    In this paper, the authors discuss energy sources, highlighting their impact on the environment and on human beings, their influence in economy and finance and on relations between governments. They attempt to analyse whether the above factors together can lead to a negative impact on health, defined as an individual's "complete physical social and psychological well being". The role of petroleum in the world economy is understandable if one considers that energy, heat, light, electricity, transportation and large part of mass production are all dependent on this energy resource. From petroleum one obtains fuel, fertilizers, pesticides, plastic, pharmaceutical products and clothing. Petroleum has become increasingly important in conjunction with expanding globalization and consumerism and the continuous growth of demand for petroleum has led to a corresponding decrease in its production and availability and an increase in its cost, all factors which have led to strong tensions between world States. The authors discuss sea and air pollution and global warming, citing some of the most relevant climatic incidents of recent years and tracing the most important events regarding attempts to contain pollution. They highlight the impact of contaminants such as greenhou se gases, electromagnetic pollution, synthetic chemicals, domestic, industrial and electronic waste products, responsible, according to neo-Lamarckian evolutionists, for the increasing incidence of chronic degenerative diseases. In conclusion the authors stress that there is a need to pursue energy efficiency while awaiting that world States succeed in their common objective of adopting new energy policies, with the use of clean energy at low cost.

  5. Renewable Energy Sources, Energy Efficiency and Reduction of Greenhouse Gas Emissions as Main Sources Development of 'Green Economy' in Croatia until 2050

    International Nuclear Information System (INIS)

    Cosic, B.; Duic, N.; Krajacic, G.; Novosel, T.; Puksec, T.; Ridjan, I.

    2012-01-01

    Most countries will need a shift in their energy strategies in order to limit the increase in global warming and to reduce the emissions of greenhouse gases. It is worrying that while technologies with little or no greenhouse gas emissions exist, and are used for a couple of decades now, the increase of their market share is extremely low and the investments and subsidies in fossil fuels are substantially larger on a world wide scale. For changes to accrue it is necessary to carefully plan both the energy consumption and supply. A correct and rational prediction of future energy consumption is the basic assumption for the advanced analysis and modelling of energy systems and it will, as an input, have a profound influence on them. In this paper a bottom up approach was selected because it is the most suitable methodology to describe the legal, economic or purely technical mechanisms. Scenarios for the energy supply in 100% renewable systems in 2050 and the possibility to create a low-carbon society were simulated using the EnergyPLAN model for energy system analysis. Comparison of the necessary useful energy for space heating in 2050 shows a difference greater than 16% for different rates of renovation of the existing buildings in the residential sector of 1% and 3% annually. The electrification of road transport for passenger cars in combination with increased requirements for energy efficiency of internal combustion engines can reduce the energy consumption in the transport sector by 30% in comparison to the reference scenario for 2050. It is possible to reduce the emission of greenhouse gases by 82% in the period 2030-2050 and the use of renewable energy sources and the production of synthetic fuels can enable a transition to a 100% renewable energy system in Croatia in 2050. Doing so would create 192000 jobs in plant maintenance and fuel production alone, increase the security of energy supply and reduce the expenditure for the purchase of fossil fuels by 4

  6. Identification of abiotic and biotic reductive dechlorination in a chlorinated ethene plume after thermal source remediation by means of isotopic and molecular biology tools

    DEFF Research Database (Denmark)

    Badin, Alice; Broholm, Mette Martina; Jacobsen, Carsten S.

    2016-01-01

    -Cl isotope analysis together with the almost absent VC 13C depletion in comparison to cDCE 13C depletion suggested that cDCE was subject to abiotic degradation due to the presence of pyrite, possible surface-bound iron (II) or reduced iron sulphides in the downgradient part of the plume. This interpretation...... reduced redox conditions which favor active reductive dechlorination and/or may lead to a series of redox reactions which may consecutively trigger biotically induced abiotic degradation. Finally, this study illustrates the valuable complementary application of compound-specific isotopic analysis combined...

  7. Switching Loss Reduction in the Three-Phase Quasi-Z-Source Inverters Utilizing Modified Space Vector Modulation Strategies

    DEFF Research Database (Denmark)

    Abdelhakim, Ahmed; Davari, Pooya; Blaabjerg, Frede

    2018-01-01

    Several single-stage topologies have been introduced since kicking off the three-phase Z-source inverter (ZSI), and among these topologies, the quasi-ZSI (qZSI) is the most common one due to its simple structure and continuous input current. Furthermore, different modulation strategies, utilizing...... multiple reference signals, have been developed as well. However, prior art modulation methods have some demerits, such as the complexity of generating the gate signals, the increased number of switch commutations with continuous commutation at high current level during the entire fundamental cycle...... the generation of the gate signals by utilizing only three reference signals, and achieving a single switch commutation at a time. These modulation strategies are analyzed and compared to the conventional ones, where a reduced-scale 1 kVA three-phase qZSI is designed and simulated using these different...

  8. Reducing the global threat of radiological terrorism in Central Asia and Caucus regions. The global threat reduction initiative approach to radioactive source security

    International Nuclear Information System (INIS)

    Smith, E.

    2010-01-01

    The security of radioactive sources is of worldwide concern, due to their wide use in civilian commerce and the potentially devastating effects of their misuse. In cooperation with host countries and international partners, the Global Threat Reduction Initiative has utilized a proven process for providing technical and financial assistance to protect radioactive sources in diverse uses and unique circumstances at hundreds of sites worldwide. The mission of the Department of Energy, National Nuclear Security Administration's program includes reducing the risk posed by vulnerable radiological materials that could be used in a Radioactive Dispersal Device). The program's objectives are to identify, consolidate, secure, and/or dispose of high-activity radiological materials to prevent their theft and malicious use. The Global Threat Reduction Initiative Program's scope is global, with projects in over 100 countries at more than 755 radiological sites, including industrial, medical and commercial facilities. In addition to working bilaterally, the Program works closely with the International Atomic Energy Agency (IAEA) and other partner countries. (author)

  9. Prevalence and sources of Campylobacter spp. contamination in free-range broiler production in the southern part of Belgium

    Directory of Open Access Journals (Sweden)

    Vandeplas, S.

    2010-01-01

    Full Text Available A one year epidemiological study was carried out between February 2005 and February 2006 in the southern part of Belgium to assess the Campylobacter prevalence in free-range broiler production. Three successive broiler flocks from six Belgian farms were investigated for the presence of Campylobacter spp. during the rearing period. Each flock was visited four times, before and after the outdoor rearing period. During each visit, samples were taken in the broiler house (litter, cecal droppings, water-lines, feed, anteroom as well as from the outer rearing environment (open-air range. The Campylobacter detection in all samples was carried out according to the ISO 10272 standard. Identification was based on colonial morphology, microscopic examination, and biochemical tests. PCR multiplex was used for genetic confirmation. Campylobacter jejuni was the main species isolated from all contaminated samples. Overall, mixed infections C. jejuni / Campylobacter coli represented 40.6%, while C. jejuni and C. coli represented 46.9% and 12.5% of chicken samples respectively. A 100% flock contamination was observed in the 6 farms during the summer-autumn period, whereas only 66.7% and 33.3% of the flocks became Campylobacter-positive in spring and winter respectively, at the end of the rearing period. Half of contaminated flocks were infected before chickens have access to the open-air range. Environmental samples, especially the open-air range soil, were found to be Campylobacter-positive before flock infection. The other potential sources of contamination were delivery tray, anteroom floor and water-lines. Other animal productions like cattle on the farm, no applied rodent control, no cleaning and disinfection of water-lines between flocks, no detergent used for cleaning and thinning were recorded as risk factors. In conclusion, the contact with the environment, particularly the access to an open-air range, appeared to be the major way of Campylobacter

  10. Effects of various organic carbon sources on simultaneous V(V) reduction and bioelectricity generation in single chamber microbial fuel cells.

    Science.gov (United States)

    Hao, Liting; Zhang, Baogang; Cheng, Ming; Feng, Chuanping

    2016-02-01

    Four ordinary carbon sources affecting V(V) reduction and bioelectricity generation in single chamber microbial fuel cells (MFCs) were investigated. Acetate supported highest maximum power density of 589.1mW/m(2), with highest V(V) removal efficiency of 77.6% during 12h operation, compared with glucose, citrate and soluble starch. Exorbitant initial V(V) concentration led to lower V(V) removal efficiencies and power outputs. Extra addition of organics had little effect on the improvement of MFCs performance. V(V) reduction and bioelectricity generation were enhanced and then suppressed by the increase of conductivity. The larger the external resistance, the higher the V(V) removal efficiencies and voltage outputs. High-throughput 16S rRNA gene pyrosequencing analysis implied the accumulation of Enterobacter which had the capabilities of V(V) reduction, electrochemical activity and fermentation, accompanied with other functional species as Pseudomonas, Spirochaeta, Sedimentibacter and Dysgonomonas. This study steps forward to remediate V(V) contaminated environment based on MFC technology. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Efficacy of a dynamic collimator for overranging dose reduction in a second- and third-generation dual source CT scanner

    Energy Technology Data Exchange (ETDEWEB)

    Booij, Ronald; Dijkshoorn, Marcel L.; Straten, Marcel van [Erasmus MC, Department of Radiology and Nuclear Medicine, P.O. Box 2240, Rotterdam (Netherlands)

    2017-09-15

    The purpose of this study was to assess the efficacy of the renewed dynamic collimator in a third-generation dual source CT (DSCT) scanner and to determine the improvements over the second-generation scanner. Collimator efficacy is defined as the percentage overranging dose in terms of dose-length product (DLP) that is blocked by the dynamic collimator relative to the total overranging dose in case of a static collimator. Efficacy was assessed at various pitch values and different scan lengths. The number of additional rotations due to overranging and effective scan length were calculated on the basis of reported scanning parameters. On the basis of these values, the efficacy of the collimator was calculated. The second-generation scanner showed decreased performance of the dynamic collimator at increasing pitch. Efficacy dropped to 10% at the highest pitch. For the third-generation scanner the efficacy remained above 50% at higher pitch. Noise was for some pitch values slightly higher at the edge of the imaged volume, indicating a reduced scan range to reduce the overranging dose. The improved dynamic collimator in the third-generation scanner blocks the overranging dose for more than 50% and is more capable of shielding radiation dose, especially in high pitch scan modes. (orig.)

  12. Efficacy of a dynamic collimator for overranging dose reduction in a second- and third-generation dual source CT scanner

    International Nuclear Information System (INIS)

    Booij, Ronald; Dijkshoorn, Marcel L.; Straten, Marcel van

    2017-01-01

    The purpose of this study was to assess the efficacy of the renewed dynamic collimator in a third-generation dual source CT (DSCT) scanner and to determine the improvements over the second-generation scanner. Collimator efficacy is defined as the percentage overranging dose in terms of dose-length product (DLP) that is blocked by the dynamic collimator relative to the total overranging dose in case of a static collimator. Efficacy was assessed at various pitch values and different scan lengths. The number of additional rotations due to overranging and effective scan length were calculated on the basis of reported scanning parameters. On the basis of these values, the efficacy of the collimator was calculated. The second-generation scanner showed decreased performance of the dynamic collimator at increasing pitch. Efficacy dropped to 10% at the highest pitch. For the third-generation scanner the efficacy remained above 50% at higher pitch. Noise was for some pitch values slightly higher at the edge of the imaged volume, indicating a reduced scan range to reduce the overranging dose. The improved dynamic collimator in the third-generation scanner blocks the overranging dose for more than 50% and is more capable of shielding radiation dose, especially in high pitch scan modes. (orig.)

  13. Review of the all Source Analysis System as a Part of the Audit of the Effectiveness of the Defense Acquisition Board Review Process-FY 1993.

    Science.gov (United States)

    1993-04-20

    OFFICE OF THE INSPECTOR GENERAL REVIEW OF THE ALL SOURCE ANALYSIS SYSTEM AS A PART OF THE AUDIT OF THE EFFECTIVENESS OF THE DEFENSE...System as a Part of the Audit of the Effectiveness of the Defense Acquisition Board Review Process--FY 1993 (Report No. 93-087) We are providing...appreciate the courtesies extended to the audit staff. If you have questions on this report, please contact Program Director Russell A. Rau at (703) 693

  14. Transmission thresholds for dengue in terms of Aedes aegypti pupae per person with discussion of their utility in source reduction efforts.

    Science.gov (United States)

    Focks, D A; Brenner, R J; Hayes, J; Daniels, E

    2000-01-01

    The expense and ineffectiveness of drift-based insecticide aerosols to control dengue epidemics has led to suppression strategies based on eliminating larval breeding sites. With the notable but short-lived exceptions of Cuba and Singapore, these source reduction efforts have met with little documented success; failure has chiefly been attributed to inadequate participation of the communities involved. The present work attempts to estimate transmission thresholds for dengue based on an easily-derived statistic, the standing crop of Aedes aegypti pupae per person in the environment. We have developed these thresholds for use in the assessment of risk of transmission and to provide targets for the actual degree of suppression required to prevent or eliminate transmission in source reduction programs. The notion of thresholds is based on 2 concepts: the mass action principal-the course of an epidemic is dependent on the rate of contact between susceptible hosts and infectious vectors, and threshold theory-the introduction of a few infectious individuals into a community of susceptible individuals will not give rise to an outbreak unless the density of vectors exceeds a certain critical level. We use validated transmission models to estimate thresholds as a function of levels of pre-existing antibody levels in human populations, ambient air temperatures, and size and frequency of viral introduction. Threshold levels were estimated to range between about 0.5 and 1.5 Ae. aegypti pupae per person for ambient air temperatures of 28 degrees C and initial seroprevalences ranging between 0% to 67%. Surprisingly, the size of the viral introduction used in these studies, ranging between 1 and 12 infectious individuals per year, was not seen to significantly influence the magnitude of the threshold. From a control perspective, these results are not particularly encouraging. The ratio of Ae. aegypti pupae to human density has been observed in limited field studies to range

  15. Challenges and Recent Developments in Hearing Aids: Part II. Feedback and Occlusion Effect Reduction Strategies, Laser Shell Manufacturing Processes, and Other Signal Processing Technologies

    Science.gov (United States)

    Chung, King

    2004-01-01

    This is the second part of a review on the challenges and recent developments in hearing aids. Feedback and the occlusion effect pose great challenges in hearing aid design and usage. Yet, conventional solutions to feedback and the occlusion effect often create a dilemma: the solution to one often leads to the other. This review discusses the advanced signal processing strategies to reduce feedback and some new approaches to reduce the occlusion effect. Specifically, the causes of three types of feedback (acoustic, mechanical, and electromagnetic) are discussed. The strategies currently used to reduce acoustic feedback (i.e., adaptive feedback reduction algorithms using adaptive gain reduction, notch filtering, and phase cancellation strategies) and the design of new receivers that are built to reduce mechanical and electromagnetic feedback are explained. In addition, various new strategies (i.e., redesigned sound delivery devices and receiver-in-the-ear-canal hearing aid configuration) to reduce the occlusion effect are reviewed. Many manufacturers have recently adopted laser shell-manufacturing technologies to overcome problems associated with manufacturing custom hearing aid shells. The mechanisms of selected laser sintering and stereo lithographic apparatus and the properties of custom shells produced by these two processes are reviewed. Further, various new developments in hearing aid transducers, telecoils, channel-free amplification, open-platform programming options, rechargeable hearing aids, ear-level frequency modulated (FM) receivers, wireless Bluetooth FM systems, and wireless programming options are briefly explained and discussed. Finally, the applications of advanced hearing aid technologies to enhance other devices such as cochlear implants, hearing protectors, and cellular phones are discussed. PMID:15735871

  16. Termination of light-water reactor core-melt accidents with a chemical core catcher: the core-melt source reduction system (COMSORS)

    International Nuclear Information System (INIS)

    Forsberg, C.W.; Parker, G.W.; Rudolph, J.C.; Osborne-Lee, I.W.; Kenton, M.A.

    1996-09-01

    The Core-Melt Source Reduction System (COMSORS) is a new approach to terminate light-water reactor core melt accidents and ensure containment integrity. A special dissolution glass is placed under the reactor vessel. If core debris is released onto the glass, the glass melts and the debris dissolves into the molten glass, thus creating a homogeneous molten glass. The molten glass, with dissolved core debris, spreads into a wide pool, distributing the heat for removal by radiation to the reactor cavity above or by transfer to water on top of the molten glass. Expected equilibrium glass temperatures are approximately 600 degrees C. The creation of a low-temperature, homogeneous molten glass with known geometry permits cooling of the glass without threatening containment integrity. This report describes the technology, initial experiments to measure key glass properties, and modeling of COMSORS operations

  17. Evaluation of non-point source pollution reduction by applying best management practices using a SWAT model and QuickBird high resolution satellite imagery.

    Science.gov (United States)

    Lee, MiSeon; Park, GeunAe; Park, MinJi; Park, JongYoon; Lee, JiWan; Kim, SeongJoon

    2010-01-01

    This study evaluated the reduction effect of non-point source pollution by applying best management practices (BMPs) to a 1.21 km2 small agricultural watershed using a SWAT (Soil and Water Assessment Tool) model. Two meter QuickBird land use data were prepared for the watershed. The SWAT was calibrated and validated using daily streamflow and monthly water quality (total phosphorus (TP), total nitrogen (TN), and suspended solids (SS)) records from 1999 to 2000 and from 2001 to 2002. The average Nash and Sutcliffe model efficiency was 0.63 for the streamflow and the coefficients of determination were 0.88, 0.72, and 0.68 for SS, TN, and TP, respectively. Four BMP scenarios viz. the application of vegetation filter strip and riparian buffer system, the regulation of Universal Soil Loss Equation P factor, and the fertilizing control amount for crops were applied and analyzed.

  18. The effectiveness of environmental strategies on noise reduction in a pediatric intensive care unit: creation of single-patient bedrooms and reducing noise sources.

    Science.gov (United States)

    Kol, Emine; Aydın, Perihan; Dursun, Oguz

    2015-07-01

    Noise is a substantial problem for both patients and healthcare workers in hospitals. This study aimed to determine the effectiveness of environmental strategies (creating single-patient rooms and reducing noise sources) in noise reduction in a pediatric intensive care unit. Noise measurement in the unit was conducted in two phases. In the first phase, measurements aimed at determining the unit's present level of noise were performed over 4 weeks in December 2013. During the month following the first measurement phase, the intensive care unit (ICU) was moved to a new location and noise-reducing strategies were implemented. The second phase, in May 2014, measured noise levels in the newly constructed environment. The noise levels before and after environmental changes were statistically significant at 72.6 dB-A and 56 dB-A, respectively (p noise-reducing strategies can be effective in controlling environmental noise in the ICU. © 2015, Wiley Periodicals, Inc.

  19. Using a source-receptor approach to characterise VOC behaviour in a French urban area influenced by industrial emissions. Part II: source contribution assessment using the Chemical Mass Balance (CMB) model.

    Science.gov (United States)

    Badol, Caroline; Locoge, Nadine; Galloo, Jean-Claude

    2008-01-25

    In Part I of this study (Badol C, Locoge N, Leonardis T, Gallo JC. Using a source-receptor approach to characterise VOC behaviour in a French urban area influenced by industrial emissions, Part I: Study area description, data set acquisition and qualitative data analysis of the data set. Sci Total Environ 2007; submitted as companion manuscript.) the study area, acquisition of the one-year data set and qualitative analysis of the data set have been described. In Part II a source profile has been established for each activity present in the study area: 6 profiles (urban heating, solvent use, natural gas leakage, biogenic emissions, gasoline evaporation and vehicle exhaust) have been extracted from literature to characterise urban sources, 7 industrial profiles have been established via canister sampling around industrial plants (hydrocarbon cracking, oil refinery, hydrocarbon storage, lubricant storage, lubricant refinery, surface treatment and metallurgy). The CMB model is briefly described and its implementation is discussed through the selection of source profiles and fitting species. Main results of CMB modellings for the Dunkerque area are presented. (1) The daily evolution of source contributions for the urban wind sector shows that the vehicle exhaust source contribution varies between 40 and 55% and its relative increase at traffic rush hours is hardly perceptible. (2) The relative contribution of vehicle exhaust varies from 55% in winter down to 30% in summer. This decrease is due to the increase of the relative contribution of hydrocarbon storage source reaching up to 20% in summer. (3) The evolution of source contributions with wind directions has confirmed that in urban wind sectors the contribution of vehicle exhaust dominate with around 45-55%. For the other wind sectors that include some industrial plants, the contribution of industrial sources is around 60% and could reach 80% for the sector 280-310 degrees , which corresponds to the most dense

  20. BioXTAS RAW: improvements to a free open-source program for small-angle X-ray scattering data reduction and analysis.

    Science.gov (United States)

    Hopkins, Jesse Bennett; Gillilan, Richard E; Skou, Soren

    2017-10-01

    BioXTAS RAW is a graphical-user-interface-based free open-source Python program for reduction and analysis of small-angle X-ray solution scattering (SAXS) data. The software is designed for biological SAXS data and enables creation and plotting of one-dimensional scattering profiles from two-dimensional detector images, standard data operations such as averaging and subtraction and analysis of radius of gyration and molecular weight, and advanced analysis such as calculation of inverse Fourier transforms and envelopes. It also allows easy processing of inline size-exclusion chromatography coupled SAXS data and data deconvolution using the evolving factor analysis method. It provides an alternative to closed-source programs such as Primus and ScÅtter for primary data analysis. Because it can calibrate, mask and integrate images it also provides an alternative to synchrotron beamline pipelines that scientists can install on their own computers and use both at home and at the beamline.

  1. Protein source in a high-protein diet modulates reductions in insulin resistance and hepatic steatosis in fa/fa Zucker rats.

    Science.gov (United States)

    Wojcik, Jennifer L; Devassy, Jessay G; Wu, Yinghong; Zahradka, Peter; Taylor, Carla G; Aukema, Harold M

    2016-01-01

    High-protein diets are being promoted to reduce insulin resistance and hepatic steatosis in metabolic syndrome. Therefore, the effect of protein source in high-protein diets on reducing insulin resistance and hepatic steatosis was examined. Fa/fa Zucker rats were provided normal-protein (15% of energy) casein, high-protein (35% of energy) casein, high-protein soy, or high-protein mixed diets with animal and plant proteins. The high-protein mixed diet reduced area under the curve for insulin during glucose tolerance testing, fasting serum insulin and free fatty acid concentrations, homeostatic model assessment index, insulin to glucose ratio, and pancreatic islet cell area. The high-protein mixed and the high-protein soy diets reduced hepatic lipid concentrations, liver to body weight ratio, and hepatic steatosis rating. These improvements were observed despite no differences in body weight, feed intake, or adiposity among high-protein diet groups. The high-protein casein diet had minimal benefits. A high-protein mixed diet was the most effective for modulating reductions in insulin resistance and hepatic steatosis independent of weight loss, indicating that the source of protein within a high-protein diet is critical for the management of these metabolic syndrome parameters. © 2015 The Obesity Society.

  2. "Innovation and Intellectual Property Policies in European Research Infrastructure Consortia - PART I: The Case of the European Spallation Source ERIC"

    DEFF Research Database (Denmark)

    Yu, Helen; Wested, Jakob; Minssen, Timo

    2017-01-01

    , the European Spallation Source ERIC is required to adopt various policy documents relating to the operation and management of the facility. These cover a wide variety of issues such as user access, public procurement, intellectual property rights (IPR), data management, and dissemination. One of the main goals...... of the problems society is facing today. To facilitate the creation and operation of such RIs, the EU adopted legal frameworks for European Research Infrastructure Consortia (ERIC). On August 31, 2015, the European Spallation Source (ESS) was established as an ERIC. Under the ERIC Regulations and ESS Statutes...... international research collaborations? The complex relationship between scientific excellence, innovation, and IPRs must be carefully considered. Taking the European Spallation Source ERIC as an example, this article investigates ERIC Regulations and EU policies and discusses what issues and perspectives ERICs...

  3. Evaluation of the quality, thermal maturity and distribution of potential source rocks in the Danish part of the Norwegian–Danish Basin

    Directory of Open Access Journals (Sweden)

    Kristensen, Lars

    2008-11-01

    Full Text Available The quality, thermal maturity and distribution of potential source rocks within the Palaeozoic–Mesozoic succession of the Danish part of the Norwegian–Danish Basin have been evaluated on the basis of screening data from over 4000 samples from the pre-Upper Cretaceous succession in 33 wells. The Lower Palaeozoic in the basin is overmature and the Upper Cretaceous – Cenozoic strata have no petroleum generation potential, but the Toarcian marine shales of the Lower Jurassic Fjerritslev Formation (F-III, F-IV members and the uppermost Jurassic – lowermost Cretaceous shales of the Frederikshavn Formation may qualify as potential source rocks in parts of the basin. Neither of these potential source rocks has a basinwide distribution; the present occurrence of the Lower Jurassic shales was primarily determined by regional early Middle Jurassic uplift and erosion. The generation potential of these source rocks is highly variable. The F-III and F-IV members show significant lateral changes in generation capacity, the best-developed source rocks occurring in the basin centre. The combined F-III andF-IV members in the Haldager-1, Kvols-1 and Rønde-1 wells contain ‘net source-rock’ thicknesses (cumulative thickness of intervals with Hydrogen Index (HI >200 mg HC/g TOC of 40 m, 83 m, and 92 m, respectively, displaying average HI values of 294, 369 and 404 mg HC/g TOC. The Mors-1 well contains 123 m of ‘net source rock’ with an average HI of 221 mg HC/g TOC. Parts of the Frederikshavn Formation possess a petroleum generation potential in the Hyllebjerg-1, Skagen-2, Voldum-1 and Terne-1 wells, the latter well containing a c.160 m thick highly oil-prone interval with an average HI of 478 mg HC/g TOC and maximum HI values >500 mg HC/g TOC. The source-rock evaluation suggests that a Mesozoic petroleum system is the most likely in the study area. Two primary plays are possible: (1 the Upper Triassic – lowermost Jurassic Gassum play, and (2the

  4. Preferential Reduction of Circulating Innate Lymphoid Cells Type 2 in Patients with Common Variable Immunodeficiency with Secondary Complications Is Part of a Broader Immune Dysregulation.

    Science.gov (United States)

    Friedmann, David; Keller, Baerbel; Harder, Ina; Schupp, Jonas; Tanriver, Yakup; Unger, Susanne; Warnatz, Klaus

    2017-11-01

    Over a third of patients with common variable immunodeficiency (CVID) suffer from secondary complications like inflammatory organ disease, autoimmune manifestations, or lymphoproliferation contributing to increased morbidity and mortality in affected patients. Innate lymphoid cells (ILCs) have emerging roles in setting the milieu for physiological, but also pathological, immune responses and inflammation. We therefore sought to correlate the recently identified disturbed homeostasis of ILCs with alterations of the adaptive immune system in complex CVID patients (CVIDc). We quantified peripheral blood ILC and T helper cell subsets of 58 CVID patients by flow cytometry and compared the results to the clinical and immunological phenotype. Total ILCs were significantly reduced in peripheral blood of CVIDc patients compared to healthy individuals, but not to CVID patients who suffered only from infections (CVIDio). This reduction was mainly due to a decrease in ILC2s, while ILC3s were relatively increased in CVIDc compared to CVIDio patients. This alteration in ILC phenotype was more prominent in patients with an expansion of CD21 low B cells, but we could not detect an association of the altered ILC phenotype with a T H 1-shift among circulating CD4 T cells, which was also prominent in CVIDc patients. We confirm a relative shift in ILCs of CVIDc patients towards ILC3s which was associated with the expansion of CD21 low B cells, but not overtly with the relative expansion of T H 1-like T cells. Given the relative abundance of T H 1-like T cells compared to ILCs, these probably represent a more prominent source of the observed IFNγ-signature in CVIDc patients.

  5. Calculation of the source term for a S1B-sequence at a VVER-1000 type reactor. Part 1

    International Nuclear Information System (INIS)

    Sdouz, G.

    1990-10-01

    The behaviour of the source term in a VVER-1000 type reactor is calculated using the 'Source Term Code Package' (STCP). The input data are based on the russian plant Zaporozhye-5. The selected accident sequence is a small break LOCA in the hot leg followed by loss offsite and onsite electric power (S 1 B-sequence). According to the course of the calculation the results are presented and analyzed for each program. Except for the noble gases all release fractions are lower than 10 -4 . 18 refs., 10 tabs. (Author)

  6. "Innovation and Intellectual Property Policies in European Research Infrastructure Consortia - PART I: The Case of the European Spallation Source ERIC"

    DEFF Research Database (Denmark)

    Yu, Helen; Wested, Jakob; Minssen, Timo

    2017-01-01

    of the problems society is facing today. To facilitate the creation and operation of such RIs, the EU adopted legal frameworks for European Research Infrastructure Consortia (ERIC). On August 31, 2015, the European Spallation Source (ESS) was established as an ERIC. Under the ERIC Regulations and ESS Statutes......, the European Spallation Source ERIC is required to adopt various policy documents relating to the operation and management of the facility. These cover a wide variety of issues such as user access, public procurement, intellectual property rights (IPR), data management, and dissemination. One of the main goals...

  7. A Two-Temperature Open-Source CFD Model for Hypersonic Reacting Flows, Part Two: Multi-Dimensional Analysis †

    OpenAIRE

    Vincent Casseau; Daniel E. R. Espinoza; Thomas J. Scanlon; Richard E. Brown

    2016-01-01

    hy2Foam is a newly-coded open-source two-temperature computational fluid dynamics (CFD) solver that has previously been validated for zero-dimensional test cases. It aims at (1) giving open-source access to a state-of-the-art hypersonic CFD solver to students and researchers; and (2) providing a foundation for a future hybrid CFD-DSMC (direct simulation Monte Carlo) code within the OpenFOAM framework. This paper focuses on the multi-dimensional verification of hy2Foam and firstly describes th...

  8. Area Source Boiler National Emission Standards for Hazardous Air Pollutants (NESHAP), 40 CFR Part 63, Subpart JJJJJJ: Questions and Answers

    Science.gov (United States)

    This October 2016 question and answer (Q&A) document is in response to a number of questions the EPA has received from delegated state and local agencies and the regulated community regarding the NESHAP for Area source boilers. Document updates 4/2014 PDF.

  9. Silurian and Devonian source rocks and crude oils from the western part of Libya: Organic geochemistry, palynology and carbon stratigraphy

    NARCIS (Netherlands)

    Elkelani, Mohamed M.A.

    2015-01-01

    The Early Silurian “hot” shales and Late Devonian black shales are major regional oil and gas source rocks in North Africa. Their deposition probably played a major role in global carbon cycling in general because of the large areas of the ocean affected. Comparing the Libyan δ13C record with

  10. Acquisition Pricing and Inventory Decisions on Dual-Source Spare-Part System with Final Production and Remanufacturing

    Directory of Open Access Journals (Sweden)

    Yancong Zhou

    2016-01-01

    Full Text Available The life spans of durable goods are longer than their warranty periods. To satisfy the service demand of spare parts and keep the market competition advantage, enterprises have to maintain the longer inventory planning of spare parts. However, how to obtain a valid number of spare parts is difficult for those enterprises. In this paper, we consider a spare-part inventory problem, where the inventory can be replenished by two ways including the final production order and the remanufacturing way. Especially for the remanufacturing way, we consider the acquisition management problem of used products concerning an acquisition pricing decision. In a multiperiod setting, we formulate the problem into a dynamic optimization problem, where the system decisions include the final production order and acquisition price of used products at each period. By stochastic dynamic programming, we obtain the optimal policy of the acquisition pricing at each period and give the optimal policy structure of the optimization problem at the first period. Then, a recursion algorithm is designed to calculate the optimal decisions and the critical points in the policy. Finally, the numerical analyses show the effects of demand information and customer’s sensitive degree on the related decisions and the optimal cost.

  11. AERMOD: A DISPERSION MODEL FOR INDUSTRIAL SOURCE APPLICATIONS PART I: GENERAL MODEL FORMULATION AND BOUNDARY LAYER CHARACTERIZATION

    Science.gov (United States)

    The formulations of the AMS/EPA Regulatory Model Improvement Committee's applied air dispersion model (AERMOD) as related to the characterization of the planetary boundary layer are described. This is the first in a series of three articles. Part II describes the formulation of...

  12. Sub products form a depuratives process of acid mine water with organic residues used as carbon source. part I; Subproductos en la depuracion de aguas acidas de mineria y empleo de residuos organicos como fuente carbonada, Parte I

    Energy Technology Data Exchange (ETDEWEB)

    Jimenez-Rodriguez, A. M.; Duran-Barrantes, M. M.; Martel-Villagran, F. J.

    2002-07-01

    Subproducts from the biological depurative process of acid mine water, such as H{sub 2}S in the biogas and HCO{sub 3} in the effluents are applied for the selective precipitation of metallic sulphides of Pb, Zn, Cu, Al an Mn, as a function of pH. To obtain the maximum H{sub 2}S concentration is principal,so several studies have been made to found the best working conditions between microorganisms and the carbon source choice. In this work,the results of the digestion process with an inoculum from the anaerobic digestion of swine manure and cheese whey as carbon source are showed. The optimal conditions obtained are: for a SO{sub 4}''=COD of 1:1,5 in HRT of 12 days, 65% of sulphate reduction, 30% of H2S in biogas. In the precipitation of metals, a reduction of 98,3% of Fe, 96,1% Cu, 79% Zn and 99% Al are obtained. AYESA (Aguas y Estructuras, S. A.) is developing the technical attendance. This study is being demonstrated under the Acid Water Treatment Program, conducted by the Consejeria del Medio Ambiente (Junta de Andalucia). (Author) 15 refs.

  13. Subproducts from a depurative process of acid mine water with organic residues used as carbon source. Part II; Subproductos en la depuracion de aguas acidas de mineria y empleo de residuos orgnicos como fuente carbonada (Parte II)

    Energy Technology Data Exchange (ETDEWEB)

    Duran-Barrantes, M. M.; Jimenez-Rodriguez, A. M.; Martel-Villagran, F. J.

    2004-07-01

    The biological depurative process of acid mine water reducing sulphate concentration from Tinto River produces the alkalinity needed for the selective precipitation of Fe, Cu, Zn and Al. But a suitable carbon source for the working conditions of microorganisms to reduce sulphates is needed. In this work, the results obtained using urban sewage as a carbon source are presented. the optimal conditions obtained are: 65,5% of sulphate reduction in HRT of 10 days for a SO{sub '}'2{sub 4} COD of 1:1 and 580 mg HS/L in the reactor effluent. In the precipitation of metals, a reduction of 77,6% of Fe, 88,6% of Cu, 70,7% of Zn and 71,5% of Al, are obtained depending on the assay applied. Ayesa is developing the technical attendance. This study is being demonstrated under the Acid Water Treatment Program, conducted by the Consejeria del Medio Ambiente (Junta de Andalucia). (Author) 6 refs.

  14. Protection against the ionizing radiations coming from external sources used in medicine: Part 1. Radiodiagnosis in medicine and dentistry

    International Nuclear Information System (INIS)

    1989-01-01

    This Venezuelan standard establishes the minimum requirements for the safety use of external sources of radiations in medical and dentistry radiodiagnosis. As a matter of fact, radiations produce noxious biological effects as: cancer, genetic damages, cataract and others. Those effects can be either avoided or limited, if we dose the exposure of radiation. The use of X-rays for diagnosis causes a massive exposure of population, that can be corrected by means of the application of rules settled down in this standard

  15. A study on an efficient prediction of welding deformation for T-joint laser welding of sandwich panel PART I : Proposal of a heat source model

    Directory of Open Access Journals (Sweden)

    Jae Woong Kim

    2013-09-01

    Full Text Available The use of I-Core sandwich panel has increased in cruise ship deck structure since it can provide similar bending strength with conventional stiffened plate while keeping lighter weight and lower web height. However, due to its thin plate thickness, i.e. about 4~6 mm at most, it is assembled by high power CO2 laser welding to minimize the welding deformation. This research proposes a volumetric heat source model for T-joint of the I-Core sandwich panel and a method to use shell element model for a thermal elasto-plastic analysis to predict welding deformation. This paper, Part I, focuses on the heat source model. A circular cone type heat source model is newly suggested in heat transfer analysis to realize similar melting zone with that observed in experiment. An additional suggestion is made to consider negative defocus, which is commonly applied in T-joint laser welding since it can provide deeper penetration than zero defocus. The proposed heat source is also verified through 3D thermal elasto-plastic analysis to compare welding deformation with experimental results. A parametric study for different welding speeds, defocus values, and welding powers is performed to investigate the effect on the melting zone and welding deformation. In Part II, focuses on the proposed method to employ shell element model to predict welding deformation in thermal elasto-plastic analysis instead of solid element model.

  16. [Calcaneal fractures treated by open reduction and internal fixation with a locking compression plate (LCP). A prospective study. part I: basic analysis of the group].

    Science.gov (United States)

    Svatoš, F; Bartoška, R; Skála-Rosenbaum, J; Douša, P; Pacovský, V; Krbec, M

    2011-01-01

    In a prospective study of patients with calcaneal fractures treated by open reduction from an extensile lateral approach and LCP osteosynthesis, the authors evaluated the basic epidemiological data, mechanism of injury, type of fracture, essential data on surgery, days of hospital stay and the number of complications. In the period from September 1, 2006 to July 31, 2010, a total of 230 patients with 243 calcaneal fractures were treated. The fractures were classified as either open or closed and according to the Essex-Lopresti system. Of the total number of patients, 135 (55.6 % of all fractures) were indicated for conservative treatment and 108 (44.4% of all fractures) for surgical intervention. Indications for surgery based on the generally accepted criteria enabled us to select 77 patients with 82 fractures (33.7 % of all fractures) for treatment by the method of open reduction and LCP osteosynthesis. These patients constituted the group evaluated here. The other patients were treated using other techniques (21 fractures, i.e., 8.6 % of all fractures, by the Stehlík-Štulík transfixation method and further five [2.1 %] by screw osteosynthesis). Six surgeons were involved in the treatment of this group. For the diagnosis of fractures, plain radiographs in lateral and axial projection and axial and coronal CT images were used. All fractures were treated after subsidence of oedema by the method of open reduction and LCP fixation from an extensile lateral approach, with the use of a tourniquet. The follow-up period for the evaluation of functional outcome and bone union was 3 to 48 months. Fifty patients were followed up for over one year. The group evaluated comprised 58 men (75.3 %) with 63 fractures (76.8 %) and 19 women (24.7 %) with 19 fractures (23.2 %). The average age of the group was 42 years, with 41 years (range, 22-61 years) in men and 47 years (range, 30-70 years) in women. The most frequent cause of injury was a fall from a height below 1 metre and

  17. Source region and sector contributions of atmospheric soot particle in a coalfield region of Dhanbad, eastern part of India

    Science.gov (United States)

    Singh, S.; Tiwari, S.; Dumka, U. C.; Kumar, R.; Singh, P. K.

    2017-11-01

    Black carbon (BC) aerosols affect the Earth's climate directly by interacting with the solar radiation and indirectly by modifying the lifetime and optical properties of clouds. However, our understanding of BC aerosols and their impacts on the climate are limited by lack of in situ measurements of BC, especially in the developing world. This study reports measurements of BC from Dhanbad, a coalfields area of eastern India, we analyze BC data at 370 and 880 nm during 2013 to gain insight into the emission sources affecting the study area. Our analysis indicates significantly higher absorption at the lower wavelength (ultraviolet). We estimate that 33% of BC at Dhanbad comes from biomass/biofuel combustion and the remaining 67% from the fossil fuel combustion. Higher concentrations of BC370 nm (> 12 μg m- 3) were observed when the air masses affecting Dhanbad originated far away in countries like Iran, Afghanistan, Pakistan, Oman, United Arab Emirates and passed over the Indo-Gangetic Plains (IGP) prior to arriving at the observation site. The source regions affecting BC880 nm were localized over the IGP but BC880 nm concentrations are 33% lower ( 8 μg m- 3) than BC370 nm. The cluster analysis showed that the largest fraction (35 and 29%) of the air masses arriving at Dhanbad passed through the boundary layer of the central IGP and north-west IGP region during the post-monsoon season. Average values of BC370 nm (16.0 and 20.0 μg m- 3) and BC880 nm (9.5 and 10.0 μg m- 3) in the IGP influenced air masses were significantly higher than those arriving from other source regions. The Weather Research and Forecasting model coupled with Chemistry (WRF-Chem) model were applied to understand the relative importance of different sources affecting Dhanbad. The variability of observed BC mass concentrations was captured fairly well by WRF-Chem with minor deviations from the measured values. Model results indicate that anthropogenic emissions account for more than 75% of the

  18. A Two-Temperature Open-Source CFD Model for Hypersonic Reacting Flows, Part One: Zero-Dimensional Analysis

    OpenAIRE

    Vincent Casseau; Rodrigo C. Palharini; Thomas J. Scanlon; Richard E. Brown

    2016-01-01

    A two-temperature CFD (computational fluid dynamics) solver is a prerequisite to any spacecraft re-entry numerical study that aims at producing results with a satisfactory level of accuracy within realistic timescales. In this respect, a new two-temperature CFD solver, hy2Foam, has been developed within the framework of the open-source CFD platform OpenFOAM for the prediction of hypersonic reacting flows. This solver makes the distinct juncture between the trans-rotational and multiple vibrat...

  19. Using geochemistry to identify the source of groundwater to Montezuma Well, a natural spring in Central Arizona, USA: Part 2

    Science.gov (United States)

    Johnson, Raymond H.; DeWitt, Ed; Wirt, Laurie; Manning, Andrew H.; Hunt, Andrew G.

    2012-01-01

    Montezuma Well is a unique natural spring located in a sinkhole surrounded by travertine. Montezuma Well is managed by the National Park Service, and groundwater development in the area is a potential threat to the water source for Montezuma Well. This research was undertaken to better understand the sources of groundwater to Montezuma Well. Strontium isotopes (87Sr/86Sr) indicate that groundwater in the recharge area has flowed through surficial basalts with subsequent contact with the underlying Permian aged sandstones and the deeper, karstic, Mississippian Redwall Limestone. The distinctive geochemistry in Montezuma Well and nearby Soda Springs (higher concentrations of alkalinity, As, B, Cl, and Li) is coincident with added carbon dioxide and mantle-sourced He. The geochemistry and isotopic data from Montezuma Well and Soda Springs allow for the separation of groundwater samples into four categories: (1) upgradient, (2) deep groundwater with carbon dioxide, (3) shallow Verde Formation, and (4) mixing zone. δ18O and δD values, along with noble gas recharge elevation data, indicate that the higher elevation areas to the north and east of Montezuma Well are the groundwater recharge zones for Montezuma Well and most of the groundwater in this portion of the Verde Valley. Adjusted groundwater age dating using likely 14C and δ13C sources indicate an age for Montezuma Well and Soda Springs groundwaters at 5,400–13,300 years, while shallow groundwater in the Verde Formation appears to be older (18,900). Based on water chemistry and isotopic evidence, groundwater flow to Montezuma Well is consistent with a hydrogeologic framework that indicates groundwater flow by (1) recharge in higher elevation basalts to the north and east of Montezuma Well, (2) movement through the upgradient Permian and Mississippian units, especially the Redwall Limestone, and (3) contact with a basalt dike/fracture system that provides a mechanism for groundwater to flow to the surface

  20. A Two-Temperature Open-Source CFD Model for Hypersonic Reacting Flows, Part Two: Multi-Dimensional Analysis †

    Directory of Open Access Journals (Sweden)

    Vincent Casseau

    2016-12-01

    Full Text Available hy2Foam is a newly-coded open-source two-temperature computational fluid dynamics (CFD solver that has previously been validated for zero-dimensional test cases. It aims at (1 giving open-source access to a state-of-the-art hypersonic CFD solver to students and researchers; and (2 providing a foundation for a future hybrid CFD-DSMC (direct simulation Monte Carlo code within the OpenFOAM framework. This paper focuses on the multi-dimensional verification of hy2Foam and firstly describes the different models implemented. In conjunction with employing the coupled vibration-dissociation-vibration (CVDV chemistry–vibration model, novel use is made of the quantum-kinetic (QK rates in a CFD solver. hy2Foam has been shown to produce results in good agreement with previously published data for a Mach 11 nitrogen flow over a blunted cone and with the dsmcFoam code for a Mach 20 cylinder flow for a binary reacting mixture. This latter case scenario provides a useful basis for other codes to compare against.

  1. A Two-Temperature Open-Source CFD Model for Hypersonic Reacting Flows, Part One: Zero-Dimensional Analysis

    Directory of Open Access Journals (Sweden)

    Vincent Casseau

    2016-10-01

    Full Text Available A two-temperature CFD (computational fluid dynamics solver is a prerequisite to any spacecraft re-entry numerical study that aims at producing results with a satisfactory level of accuracy within realistic timescales. In this respect, a new two-temperature CFD solver, hy2Foam, has been developed within the framework of the open-source CFD platform OpenFOAM for the prediction of hypersonic reacting flows. This solver makes the distinct juncture between the trans-rotational and multiple vibrational-electronic temperatures. hy2Foam has the capability to model vibrational-translational and vibrational-vibrational energy exchanges in an eleven-species air mixture. It makes use of either the Park TTv model or the coupled vibration-dissociation-vibration (CVDV model to handle chemistry-vibration coupling and it can simulate flows with or without electronic energy. Verification of the code for various zero-dimensional adiabatic heat baths of progressive complexity has been carried out. hy2Foam has been shown to produce results in good agreement with those given by the CFD code LeMANS (The Michigan Aerothermodynamic Navier-Stokes solver and previously published data. A comparison is also performed with the open-source DSMC (direct simulation Monte Carlo code dsmcFoam. It has been demonstrated that the use of the CVDV model and rates derived from Quantum-Kinetic theory promote a satisfactory consistency between the CFD and DSMC chemistry modules.

  2. A source of almost pure methyl chavicol: volatile oil from the aerial parts of Tagetes lucida (Asteraceaecultivated in Costa Rica

    Directory of Open Access Journals (Sweden)

    José F Cicció

    2004-12-01

    Full Text Available The plant Tagetes lucida Cav.(syn.T.florida Sweet,T.schiedeana Less.is an aromatic herb distributed naturally from Mexico to Honduras,at elevations between 1 000 and 2 000 m.It is used as a spice,for medicine,as insecticide and as ornamental plant.It is cultivated commercially in Costa Rica as a spice herb;it contains an oil having an anise-like odor,and the fresh aerial parts of this plant are sold in the supermarket as a substitute of tarragon (Artemisia dracunculus L..The essential oils isolated from aerial parts bought,at May and October,in a supermarket in San José (Costa Rica.Fresh flowering aerial parts,flowers and leaves plus stems, were subjected to hydrodistillation for 3 hr using a modified Clevenger-type apparatus.The distilled oils were collected and dried over anhydrous sodium sulphate and stored in a freezer (0-10 °C.The light yellow green oil yield was about 0.07%(v/w.GC/MS analyses were performed using a Shimadzu GCMS-QP5050 apparatus and CLASS 5000 software with Wiley 139 computer database.Identification of the components of the oil was performed using the retention indices,which were calculated in relation to a homologous series of hydrocarbons, and by comparison of their mass spectra with those published in the literature or those of our own database. Thirty compounds were identified,of which methyl chavicol (95-97%was the major constituent.From flower oil,two bithienyls were detected as minor constituents. Rev. Biol. Trop. 52(4:853-857.Epub 2005 Jun 24.Los aceites esenciales extraídos de las partes aéreas de la planta Tagetes lucida Cav.cultivada en Costa Rica y utilizada como condimento,fue estudiado mediante la técnica de GC/MS en combinación con los índices de retención.Se identificaron treinta compuestos.El componente mayoritario resultó ser metil chavicol (estragolen un 95-97%.En el aceite de las flores se detectaron e identificaron dos compuestos minoritarios que resultaron ser bitienilos no informados

  3. Increase of COP for heat transformer in water purification systems. Part II - Without increasing heat source temperature

    International Nuclear Information System (INIS)

    Romero, R.J.; Siqueiros, J.; Huicochea, A.

    2007-01-01

    The integration of a water purification system allows a heat transformer to increase the actual coefficient of performance, by the reduction of the amount of heat supplied by unit of heat. A new defined COP called COP WP is proposed for the present system, which considers the fraction of heat recycled. Simulation with proven software compares the performance of the modeling of an absorption heat transformer for water purification (AHTWP) operating with water/lithium bromide, as working fluid-absorbent pair. Plots of enthalpy-based coefficients of performance (COP ET ) and water purification coefficient of performance (COP WP ) are shown against absorber temperature for several thermodynamic operating conditions. The results showed that the proposed (AHTWP) system is capable of increasing the original value of COP ET up to 1.6 times its original value by recycling energy from a water purification system. The proposed COP WP allows increments for COP values from any experimental data for water purification or for any other distillation system integrated to a heat transformer, regardless of actual COP A value or working fluid-absorbent pair

  4. Consumption of forest chips as an energy source as part of the national action plan for renewable energy

    International Nuclear Information System (INIS)

    Ylitalo, E.

    2004-01-01

    A specific Action Plan for Renewable Energy was introduced in 1999 in order to increase the utilisation of renewable energy sources in Finland. The Plan was renewed in 2002, taking into account a revision of the goals defined in the statements given by the Parliament in the de-bate on national Climate Strategy and the decision on building a new nuclear power plant. The main reason for increasing the consumption of renewable energy is the aim of decreasing emissions of greenhouse gases caused by fossil fuels. The renewed Action Plan includes aims and means of how to increase the consumption of renewable energy in practice in the future. Specific goals for separate renewable energy sources were set for the years 2005, 2010 and 2025. Proportional targets were set for the consumption of forest chips: in 2010 consumption is expected to be four times larger than in 2001 and in 2025 seven times larger. In Finland, the most important source for renewable energy is wood and wood waste, which currently makes up approximately 20 per cent of total energy consumption. Wood waste (incl. waste liquor and solid wood waste) produced by the forest industries can be considered as being fully utilized at the moment. Therefore, the most important means of increasing the consumption of wood energy in the future is in the utilisation of forest chips resources. Since 2000, the Finnish Forest Re-search Institute has compiled statistics on the consumption of forest chips and forest industry by-products used in energy generation. One aim of these statistics is to monitor the fruition of the Action Plan mentioned. In 2003, the volume of forest chips consumed in energy generation was 2.1 mill. m3, i.e. approximately five per cent of all energy sources consumed. According to the statistics, the consumption of forest chips has doubled during the period 2000-2003 with an annual average increase of 0.4 mill. m 3 . The goals set in the Action Plan can be considered to be high. In order to achieve

  5. Modeling dry and wet deposition of sulfate, nitrate, and ammonium ions in Jiuzhaigou National Nature Reserve, China using a source-oriented CMAQ model: Part II. Emission sector and source region contributions.

    Science.gov (United States)

    Qiao, Xue; Tang, Ya; Kota, Sri Harsha; Li, Jingyi; Wu, Li; Hu, Jianlin; Zhang, Hongliang; Ying, Qi

    2015-11-01

    A source-oriented Community Multiscale Air Quality (CMAQ) model driven by the meteorological fields generated by the Weather Research and Forecasting (WRF) model was used to study the dry and wet deposition of nitrate (NO3(-)), sulfate (SO4(2-)), and ammonium (NH4(+)) ions in the Jiuzhaigou National Nature Reserve (JNNR), China from June to August 2010 and to identify the contributions of different emission sectors and source regions that were responsible for the deposition fluxes. Contributions from power plants, industry, transportation, domestic, biogenic, windblown dust, open burning, fertilizer, and manure management sources to deposition fluxes in JNNR watershed and four EANET sites are determined. In JNNR, 96%, 82%, and 87% of the SO4(2-), NO3(-) and NH4(+) deposition fluxes are in the form of wet deposition of the corresponding aerosol species. Industry and power plants are the two major sources of SO4(2-) deposition flux, accounting for 86% of the total wet deposition of SO4(2-), and industry has a higher contribution (56%) than that of power plants (30%). Power plants and industry are also the top sources that are responsible for NO3(-) wet deposition, and contributions from power plants (30%) are generally higher than those from industries (21%). The major sources of NH4(+) wet deposition flux in JNNR are fertilizer (48%) and manure management (39%). Source-region apportionment confirms that SO2 and NOx emissions from local and two nearest counties do not have a significant impact on predicted wet deposition fluxes in JNNR, with contributions less than 10%. While local NH3 emissions account for a higher fraction of the NH4(+) deposition, approximately 70% of NH4(+) wet deposition in JNNR originated from other source regions. This study demonstrates that S and N deposition in JNNR is mostly from long-range transport rather than from local emissions, and to protect JNNR, regional emission reduction controls are needed. Copyright © 2015 Elsevier B.V. All

  6. Natural mineral bottled waters available on the Polish market as a source of minerals for the consumers. Part 2: The intake of sodium and potassium.

    Science.gov (United States)

    Gątarska, Anna; Ciborska, Joanna; Tońska, Elżbieta

    Natural mineral waters are purchased and consumed according to consumer preferences and possible recommendations. The choice of appropriate water should take into account not only the general level of mineralization but also the content of individual components, including electrolytes such as sodium and potassium. Sodium is necessary to ensure the proper physiological functions of the body. It is defined as a health risk factor only when its excessive intake occurs. Potassium acts antagonistically towards sodium and calcium ions, contributes to a reduction of the volume of extracellular fluids and at the same time reduces muscle tension and permeability of cell membranes. The demand for sodium and potassium is of particular importance in people expending significant physical effort, where an increased electrolyte supply is recommended. The aim of the study was to estimate the content of sodium and potassium in natural mineral waters available in the Polish market and to evaluate the intake of those components with the commercially available mineral waters by different groups of consumers at the assumed volume of their consumption. The research material consisted of natural mineral waters of forty various brands available on the Polish market. The examined products were either produced in Poland or originated in other European countries. Among the products under examination, about 30% of the waters were imported from Lithuania, Latvia, the Czech Republic, France, Italy and Germany. A sample for analyses consisted of two package units of the examined water from different production lots. Samples for research were collected at random. The study was conducted with the same samples in in which calcium and magnesium content was determined, which was the subject of the first part of the study. The content of sodium and potassium was determined using the emission technique (acetylene-air flame), with the use of atomic absorption spectrometer – ICE 3000 SERIES – THERMO

  7. Dose reduction in abdominal computed tomography: intraindividual comparison of image quality of full-dose standard and half-dose iterative reconstructions with dual-source computed tomography.

    Science.gov (United States)

    May, Matthias S; Wüst, Wolfgang; Brand, Michael; Stahl, Christian; Allmendinger, Thomas; Schmidt, Bernhard; Uder, Michael; Lell, Michael M

    2011-07-01

    We sought to evaluate the image quality of iterative reconstruction in image space (IRIS) in half-dose (HD) datasets compared with full-dose (FD) and HD filtered back projection (FBP) reconstruction in abdominal computed tomography (CT). To acquire data with FD and HD simultaneously, contrast-enhanced abdominal CT was performed with a dual-source CT system, both tubes operating at 120 kV, 100 ref.mAs, and pitch 0.8. Three different image datasets were reconstructed from the raw data: Standard FD images applying FBP which served as reference, HD images applying FBP and HD images applying IRIS. For the HD data sets, only data from 1 tube detector-system was used. Quantitative image quality analysis was performed by measuring image noise in tissue and air. Qualitative image quality was evaluated according to the European Guidelines on Quality criteria for CT. Additional assessment of artifacts, lesion conspicuity, and edge sharpness was performed. : Image noise in soft tissue was substantially decreased in HD-IRIS (-3.4 HU, -22%) and increased in HD-FBP (+6.2 HU, +39%) images when compared with the reference (mean noise, 15.9 HU). No significant differences between the FD-FBP and HD-IRIS images were found for the visually sharp anatomic reproduction, overall diagnostic acceptability (P = 0.923), lesion conspicuity (P = 0.592), and edge sharpness (P = 0.589), while HD-FBP was rated inferior. Streak artifacts and beam hardening was significantly more prominent in HD-FBP while HD-IRIS images exhibited a slightly different noise pattern. Direct intrapatient comparison of standard FD body protocols and HD-IRIS reconstruction suggest that the latest iterative reconstruction algorithms allow for approximately 50% dose reduction without deterioration of the high image quality necessary for confident diagnosis.

  8. Romania. Regular Review 2006. Part 1. Trends in energy and energy efficiency policies, instruments and actors. Part 2. Indicators on Energy, Energy Efficiency, Economy and Environment. Based on national sources of data

    International Nuclear Information System (INIS)

    2006-01-01

    Although Romania has the largest oil and gas resources in Central Europe, it is nonetheless a net importer of hydrocarbons, and the efficient use of energy along the entire energy chain from production to consumption has been a consistent feature of Romanian policy in recent years. Romania's national energy strategy foresees an annual reduction of the energy intensity of the national economy of approximately 3%. Energy efficiency measures have concentrated on the industrial and residential sectors, where there is the clearest scope for improvements. Programmes for the services and transport sectors are now also being developed. As Romania prepares for accession to the European Union, the PEEREA review of Romania's energy efficiency policies and programmes provides a detailed overview of the transposition of the relevant parts of the EU acquis, as well as an insight into particular challenges for Romania - such as the modernisation of the district heating network, which accounts for a third of the country's heat and hot water demand

  9. Overview of major hazards. Part 2: Source term; dispersion; combustion; blast, missiles, venting; fire; radiation; runaway reactions; toxic substances; dust explosions

    Science.gov (United States)

    Vilain, J.

    Approaches to major hazard assessment and prediction are reviewed. Source term: (phenomenology/modeling of release, influence on early stages of dispersion); dispersion (atmospheric advection, diffusion and deposition, emphasis on dense/cold gases); combustion (flammable clouds and mists covering flash fires, deflagration, transition to detonation; mostly unconfined/partly confined situations); blast formation, propagation, interaction with structures; catastrophic fires (pool fires, torches and fireballs; highly reactive substances) runaway reactions; features of more general interest; toxic substances, excluding toxicology; and dust explosions (phenomenology and protective measures) are discussed.

  10. Reduction of CO2 emissions during cement clinker burning : Part 2 = Ein Beitrag zur Reduzierung der CO2-Emissionen beim Zementklinkerbrand; Teil 2

    NARCIS (Netherlands)

    Vogel, S.; Kolditz, K.; Beilmann, F.; Finger, F.A.; Ott-Reinhardt, D.; Kralisch, D.

    2013-01-01

    The aim of the research project entitled "New technology in cement production for reducing CO2 emissions" sponsored by the German Federal Environmental Foundation was to lower the CO2 emissions during clinker burning. A possible reduction, relative to an industrial example, of up to 21 % in the

  11. Reduction of CO2 emissions during cement clinker burning; part 1 = Ein Beitrag zur Reduzierung der CO2-Emissionen beim Zementklinkerbrand; Teil 1

    NARCIS (Netherlands)

    Vogel, S.; Kolditz, K.; Bellmann, F.; Ott-Reinhardt, D.; Kralisch, D.

    2013-01-01

    The aim of the research project entitled "New technology in cement production for reducing CO2 emissions" sponsored by the German Federal Environmental Foundation was to lower the CO2 emissions during clinker burning. A possible reduction, relative to an industrial example, of up to 21 % in the

  12. Source of salts in the Waianae part of the Pearl Harbor aquifer near Barbers Point water tunnel, Oahu, Hawaii

    Science.gov (United States)

    Eyre, P.R.

    1987-01-01

    The salinity of the water supply of Barbers Point Naval Air Station has increased markedly since 1983. The Naval Air Station obtains its water, about 3 million gal/day, from Barbers Point shaft, a water shaft that taps the Waianae part of the Pearl Harbor aquifer underlying the dry, southeastern flank of the Waianae mountains on the island on Oahu, Hawaii. From 1983 to 1985 the chloride concentration of the water, increased from 220 to 250 mg/L and has remained near that level through 1986. The EPA has established 250 mg/L as the maximum recommended chloride concentration in drinking water because above that level many people can taste the salt. The high chloride concentration in shallow groundwater at all wells in the area indicates that most of the salts in the freshwater lens are contributed by rainfall, sea spray, and irrigation return water. At Barbers Point shaft, pumping may draw a small amount of saltwater from the transition zone and increase the chloride concentration in the pumped water by about 20 mg/L. Salinity of the lens decreases progressively inland in response to recharge from relatively fresher water and in response to an increasing lens thickness with increasing distance from the shoreline. The increase, in 1983, in the chloride concentration of water at the shaft was most probably the result of saltier recharge water reaching the water table, and not the result of increased mixing of underlying saltwater with the freshwater. The chloride concentration of the recharge water has probably increased because, in 1980, the drip method of irrigation began to replace the furrow method on sugarcane fields near the shaft. A mixing-cell model was used to estimate the effect of drip irrigation on the chloride concentration of the groundwater in the vicinity of Barbers Point shaft. The model predicted an increase in chloride concentration of about 50 mg/L. The observed increase was about 30 mg/L and the chloride concentration is presently stable at 245 to

  13. Reduction of artificial source effect in the high-resolution aeromagnetic survey in the Hanshin region; Hanshin chiiki no komitsudo kuchu jiki tansa ni okeru jinko noise source no eikyo no jokyo

    Energy Technology Data Exchange (ETDEWEB)

    Nakatsuka, T; Makino, M; Morijiri, R; Okuma, S [Geological Survey of Japan, Tsukuba (Japan)

    1997-05-27

    A high-resolution aeromagnetic survey was carried out in December 1995 on areas from Kobe City to Kyoto City in relation to the Hyogoken-nanbu Earthquake in 1995. It was found in the survey that effects of electric trains driven by direct current and man-made structures cannot be avoided, working as a large noise factor in extraction and analysis of geological information. This paper describes a quantitative analysis on magnetic anomaly suspected to have been caused from artificial sources seen in the magnetic map of the Hanshin area obtained from the above exploration data. The paper also gives considerations on methods to remove the effects therefrom. It then describes a quantitative analysis and the result of attempts on removal of the anomaly, taking up the following factors: (1) distribution of specific and remarkable magnetic anomalies which correspond to railroad positions of the Hanshin Railways running through the Nishinomiya-Toyonaka area, (2) the magnetic anomaly trend in positive and negative pair seen in the seafront area of Kobe City, and (3) typical bipolar isolated type magnetic anomaly in the north-west part of Kobe City. The cause for (1) was loop current flown for the railway operation, that for (2) was man-made structures in the improved seafront area, and that for (3) was a provisionally built metal waste storage yard. 9 figs.

  14. Selective reduction of arsenic species by hydride generation - atomic absorption spectrometry. Part 2 - sample storage and arsenic determination in natural waters

    Directory of Open Access Journals (Sweden)

    Quináia Sueli P.

    2001-01-01

    Full Text Available Total arsenic, arsenite, arsinate and dimethylarsinic acid (DMA were selectively determined in natural waters by hydride generation - atomic absorption spectrometry, using sodium tetrahydroborate(III as reductant but in different reduction media. River water samples from the north region of Paraná State, Brazil, were analysed and showed arsenate as the principal arsenical form. Detection limits found for As(III (citrate buffer, As(III + DMA (acetic acid and As(III + As(V (hydrochloric acid were 0.6, 1.1 and 0.5 mg As L-1, respectively. Sample storage on the proper reaction media revealed to be a useful way to preserve the water sample.

  15. ACTRIS ACSM intercomparison - Part 2: Intercomparison of ME-2 organic source apportionment results from 15 individual, co-located aerosol mass spectrometers

    Science.gov (United States)

    Fröhlich, R.; Crenn, V.; Setyan, A.; Belis, C. A.; Canonaco, F.; Favez, O.; Riffault, V.; Slowik, J. G.; Aas, W.; Aijälä, M.; Alastuey, A.; Artiñano, B.; Bonnaire, N.; Bozzetti, C.; Bressi, M.; Carbone, C.; Coz, E.; Croteau, P. L.; Cubison, M. J.; Esser-Gietl, J. K.; Green, D. C.; Gros, V.; Heikkinen, L.; Herrmann, H.; Jayne, J. T.; Lunder, C. R.; Minguillón, M. C.; Močnik, G.; O'Dowd, C. D.; Ovadnevaite, J.; Petralia, E.; Poulain, L.; Priestman, M.; Ripoll, A.; Sarda-Estève, R.; Wiedensohler, A.; Baltensperger, U.; Sciare, J.; Prévôt, A. S. H.

    2015-06-01

    Chemically resolved atmospheric aerosol data sets from the largest intercomparison of the Aerodyne aerosol chemical speciation monitors (ACSMs) performed to date were collected at the French atmospheric supersite SIRTA. In total 13 quadrupole ACSMs (Q-ACSM) from the European ACTRIS ACSM network, one time-of-flight ACSM (ToF-ACSM), and one high-resolution ToF aerosol mass spectrometer (AMS) were operated in parallel for about 3 weeks in November and December~2013. Part 1 of this study reports on the accuracy and precision of the instruments for all the measured species. In this work we report on the intercomparison of organic components and the results from factor analysis source apportionment by positive matrix factorisation (PMF) utilising the multilinear engine 2 (ME-2). Except for the organic contribution of mass-to-charge ratio m/z 44 to the total organics (f44), which varied by factors between 0.6 and 1.3 compared to the mean, the peaks in the organic mass spectra were similar among instruments. The m/z 44 differences in the spectra resulted in a variable f44 in the source profiles extracted by ME-2, but had only a minor influence on the extracted mass contributions of the sources. The presented source apportionment yielded four factors for all 15 instruments: hydrocarbon-like organic aerosol (HOA), cooking-related organic aerosol (COA), biomass burning-related organic aerosol (BBOA) and secondary oxygenated organic aerosol (OOA). ME-2 boundary conditions (profile constraints) were optimised individually by means of correlation to external data in order to achieve equivalent / comparable solutions for all ACSM instruments and the results are discussed together with the investigation of the influence of alternative anchors (reference profiles). A comparison of the ME-2 source apportionment output of all 15 instruments resulted in relative standard deviations (SD) from the mean between 13.7 and 22.7 % of the source's average mass contribution depending on the

  16. ACTRIS ACSM intercomparison – Part 2: Intercomparison of ME-2 organic source apportionment results from 15 individual, co-located aerosol mass spectrometers

    Directory of Open Access Journals (Sweden)

    R. Fröhlich

    2015-06-01

    Full Text Available Chemically resolved atmospheric aerosol data sets from the largest intercomparison of the Aerodyne aerosol chemical speciation monitors (ACSMs performed to date were collected at the French atmospheric supersite SIRTA. In total 13 quadrupole ACSMs (Q-ACSM from the European ACTRIS ACSM network, one time-of-flight ACSM (ToF-ACSM, and one high-resolution ToF aerosol mass spectrometer (AMS were operated in parallel for about 3 weeks in November and December~2013. Part 1 of this study reports on the accuracy and precision of the instruments for all the measured species. In this work we report on the intercomparison of organic components and the results from factor analysis source apportionment by positive matrix factorisation (PMF utilising the multilinear engine 2 (ME-2. Except for the organic contribution of mass-to-charge ratio m/z 44 to the total organics (f44, which varied by factors between 0.6 and 1.3 compared to the mean, the peaks in the organic mass spectra were similar among instruments. The m/z 44 differences in the spectra resulted in a variable f44 in the source profiles extracted by ME-2, but had only a minor influence on the extracted mass contributions of the sources. The presented source apportionment yielded four factors for all 15 instruments: hydrocarbon-like organic aerosol (HOA, cooking-related organic aerosol (COA, biomass burning-related organic aerosol (BBOA and secondary oxygenated organic aerosol (OOA. ME-2 boundary conditions (profile constraints were optimised individually by means of correlation to external data in order to achieve equivalent / comparable solutions for all ACSM instruments and the results are discussed together with the investigation of the influence of alternative anchors (reference profiles. A comparison of the ME-2 source apportionment output of all 15 instruments resulted in relative standard deviations (SD from the mean between 13.7 and 22.7 % of the source's average mass contribution depending on

  17. A two-microphone noise reduction system for cochlear implant users with nearby microphones. Part I: Signal processing algorithm design and development

    OpenAIRE

    Kompis, Martin; Bertram, Matthias; François, Jacques; Pelizzone, Marco

    2008-01-01

    Users of cochlear implant systems, that is, of auditory aids which stimulate the auditory nerve at the cochlea electrically, often complain about poor speech understanding in noisy environments. Despite the proven advantages of multimicrophone directional noise reduction systems for conventional hearing aids, only one major manufacturer has so far implemented such a system in a product, presumably because of the added power consumption and size. We present a physically small (intermicrophone ...

  18. Global threat reduction initiative (GTRI)

    International Nuclear Information System (INIS)

    Chamberlain, Travis

    2009-01-01

    The Global Threat Reduction Initiative (GTRI) is a vital part of the global efforts to combat nuclear terrorism. GTRI's unique mission to reduce and protect vulnerable nuclear and radiological material located at civilian sites both in the United States and abroad directly addresses recommendations of the bipartisan 9/11 Commission. GTRI efforts are focused on the first line of defense, namely securing or removing vulnerable nuclear and radiological material at the source. The international community has promulgated guidance on the best practice on the technical and administrative aspects of radiological source security, and the GTRI seeks to provide technical assistance to national bodies and individual facilities to adopt this best practice. This presentation will discuss security concepts that are implemented by the GTRI in cooperation with the Australian Nuclear Science and Technology Organization's Regional Security of Radioactive Sources Project. (author)

  19. When probabilistic seismic hazard climbs volcanoes: the Mt. Etna case, Italy – Part 1: Model components for sources parameterization

    Directory of Open Access Journals (Sweden)

    R. Azzaro

    2017-11-01

    implemented in PSHA maps. They can be relevant for the retrofitting of the existing building stock and for driving risk reduction interventions. These analyses do not account for regional M  >  6 seismogenic sources which dominate the hazard over long return times (≥ 500 years.

  20. [Study of self-reported health of people living near point sources of environmental pollution: a review. Second part: analysis of results and perspectives].

    Science.gov (United States)

    Daniau, C; Dor, F; Eilstein, D; Lefranc, A; Empereur-Bissonnet, P; Dab, W

    2013-08-01

    Epidemiological studies have investigated the health impacts of local sources of environmental pollution using as an outcome variable self-reported health, reflecting the overall perception interviewed people have of their own health. This work aims at analyzing the advantages and the results of this approach. This second part presents the results of the studies. Based on a literature review (51 papers), this article presents an analysis of the contribution of self-reported health to epidemiological studies investigating local sources of environmental pollution. It discusses the associations between self-reported health and exposure variables, and other risk factors that can influence health reporting. Studies using self-reported health showed that local sources can be associated with a wide range of health outcomes, including an impact on mental health and well-being. The perception of pollution, especially sensory information such as odors, affects self-reported health. Attitudes referring to beliefs, worries and personal behaviors concerning the source of pollution have a striking influence on reported health. Attitudes can be used to estimate the reporting bias in a biomedical approach, and also constitute the main explanatory factors in biopsychosocial studies taking into account not only the biological, physical, and chemical factors but also the psychological and social factors at stake in a situation of environmental exposure. Studying self-reported health enables a multifactorial approach to health in a context of environmental exposure. This approach is most relevant when conducted within a multidisciplinary framework involving human and social sciences to better understand psychosocial factors. The relevance of this type of approach used as an epidemiological surveillance tool to monitor local situations should be assessed with regard to needs for public health management of these situations. Copyright © 2013 Elsevier Masson SAS. All rights reserved.

  1. Magnetic Data Interpretation for the Source-Edge Locations in Parts of the Tectonically Active Transition Zone of the Narmada-Son Lineament in Central India

    Science.gov (United States)

    Ghosh, G. K.

    2016-02-01

    The study has been carried out in the transition zone of the Narmada-Son lineament (NSL) which is seismically active with various geological complexities, upwarp movement of the mantle material into the crust through fault, fractures lamination and upwelling. NSL is one of the most prominent lineaments in central India after the Himalaya in the Indian geology. The area of investigation extends from longitude 80.25°E to 81.50°E and latitude 23.50°N to 24.37°N in the central part of the Indian continent. Different types of subsurface geological formations viz. alluvial, Gondwana, Deccan traps, Vindhyan, Mahakoshal, Granite and Gneisses groups exist in this area with varying geological ages. In this study area tectonic movement and crustal variation have been taken place during the past time and which might be reason for the variation of magnetic field. Magnetic anomaly suggests that the area has been highly disturbed which causes the Narmada-Son lineament trending in the ENE-WSW direction. Magnetic anomaly variation has been taken place due to the lithological variations subject to the changes in the geological contacts like thrusts and faults in this area. Shallow and deeper sources have been distinguished using frequency domain analysis by applying different filters. To enhance the magnetic data, various types of derivatives to identify the source-edge locations of the causative source bodies. The present study carried out the interpretation using total horizontal derivative, tilt angle derivative, horizontal tilt angle derivative and Cos (θ) derivative map to get source-edge locations. The results derived from various derivatives of magnetic data have been compared with the basement depth solutions calculated from 3D Euler deconvolution. It is suggested that total horizontal derivative, tilt angle derivative and Cos (θ) derivative are the most useful tools for identifying the multiple source edge locations of the causative bodies in this tectonically active

  2. Selective catalytic reduction of NO{sub x} to nitrogen over Co-Pt/ZSM-5: Part A. Characterization and kinetic studies

    Energy Technology Data Exchange (ETDEWEB)

    Maisuls, S.E.; Seshan, K.; Feast, S.; Lercher, J.A. [Laboratory for Catalytic Processes and Materials, Faculty of Chemical Technology, University of Twente, P.O. Box 217, 7500 AE Enschede (Netherlands)

    2001-01-01

    The selective catalytic reduction of NO by propene in the presence of excess oxygen has been studied over catalysts based on Co-Pt supported on ZSM-5. Pure Pt based catalysts are highly active, but produce large amounts of N{sub 2}O. Bimetallic Co-Pt/ZSM-5 catalysts with low Pt contents (0.1wt.%) show a synergistic effect by combining high stability and activity of Pt catalysts with the high N{sub 2} selectivity of Co catalysts. The lower selectivity to N{sub 2}O is attributed to its selective conversion over Co. The catalysts also showed high water and sulfur tolerance above 350C.

  3. A study of the reverse cycle defrosting performance on a multi-circuit outdoor coil unit in an air source heat pump – Part I: Experiments

    International Nuclear Information System (INIS)

    Qu, Minglu; Xia, Liang; Deng, Shiming; Jiang, Yiqiang

    2012-01-01

    Highlights: ► We experimental study the defrosting performance on a multi-circuit outdoor coil unit in an ASHP unit. ► We find that defrosting is quicker on the airside of upper circuits than that on the lower circuits. ► We discuss the effects of downwards flowing of the melted frost along the outdoor coil surface on defrosting performance. -- Abstract: When an air source heat pump (ASHP) unit operates in heating mode, frost can be accumulated on the surface of its finned outdoor coil which normally has multiple parallel circuits on its refrigerant side for minimized refrigerant pressure loss and enhanced heat transfer efficiency. On its airside, however, there is usually no segmentation corresponding to the number of refrigerant circuit. Frosting deteriorates the operation and energy efficiency of the ASHP unit and periodic defrosting becomes necessary. Currently the most widely used standard defrosting method for ASHPs is reverse cycle defrost. This paper, the first part of a two-part series, reports on the experimental part of a study of the reverse cycle defrosting performance on a multi-circuit outdoor coil unit in an experimental 6.5 kW heating capacity residential ASHP unit. Firstly the experimental ASHP unit is described and experimental procedures detailed. Secondly, the experimental results are reported. This is followed by the discussion on the effects of downwards flowing of the melted frost along a multi-circuit outdoor coil surface on defrosting performance. Finally, the evaluation of the defrosting efficiency for the experimental ASHP unit is provided. In the second part of the series, a modeling analysis on the effects of downwards flowing of the melted frost along the multi-circuit outdoor coil surface on defrosting performance of the experimental ASHP unit will be presented.

  4. Harm reduction services as a point-of-entry to and source of end-of-life care and support for homeless and marginally housed persons who use alcohol and/or illicit drugs: a qualitative analysis.

    Science.gov (United States)

    McNeil, Ryan; Guirguis-Younger, Manal; Dilley, Laura B; Aubry, Tim D; Turnbull, Jeffrey; Hwang, Stephen W

    2012-05-17

    Homeless and marginally housed persons who use alcohol and/or illicit drugs often have end-of-life care needs that go unmet due to barriers that they face to accessing end-of-life care services. Many homeless and marginally housed persons who use these substances must therefore rely upon alternate sources of end-of-life care and support. This article explores the role of harm reduction services in end-of-life care services delivery to homeless and marginally housed persons who use alcohol and/or illicit drugs. A qualitative case study design was used to explore end-of-life care services delivery to homeless and marginally housed persons in six Canadian cities. A key objective was to explore the role of harm reduction services. 54 health and social services professionals participated in semi-structured qualitative interviews. All participants reported that they provided care and support to this population at end-of-life. Harm reduction services (e.g., syringe exchange programs, managed alcohol programs, etc.) were identified as a critical point-of-entry to and source of end-of-life care and support for homeless and marginally housed persons who use alcohol and/or illicit drugs. Where possible, harm reduction services facilitated referrals to end-of-life care services for this population. Harm reduction services also provided end-of-life care and support when members of this population were unable or unwilling to access end-of-life care services, thereby improving quality-of-life and increasing self-determination regarding place-of-death. While partnerships between harm reduction programs and end-of-life care services are identified as one way to improve access, it is noted that more comprehensive harm reduction services might be needed in end-of-life care settings if they are to engage this underserved population.

  5. Sorbitol dehydrogenase of Aspergillus niger, SdhA, is part of the oxido-reductive D-galactose pathway and essential for D-sorbitol catabolism.

    Science.gov (United States)

    Koivistoinen, Outi M; Richard, Peter; Penttilä, Merja; Ruohonen, Laura; Mojzita, Dominik

    2012-02-17

    In filamentous fungi D-galactose can be catabolised through the oxido-reductive and/or the Leloir pathway. In the oxido-reductive pathway D-galactose is converted to d-fructose in a series of steps where the last step is the oxidation of d-sorbitol by an NAD-dependent dehydrogenase. We identified a sorbitol dehydrogenase gene, sdhA (JGI53356), in Aspergillus niger encoding a medium chain dehydrogenase which is involved in D-galactose and D-sorbitol catabolism. The gene is upregulated in the presence of D-galactose, galactitol and D-sorbitol. An sdhA deletion strain showed reduced growth on galactitol and growth on D-sorbitol was completely abolished. The purified enzyme converted D-sorbitol to D-fructose with K(m) of 50±5 mM and v(max) of 80±10 U/mg. Copyright © 2012 Federation of European Biochemical Societies. Published by Elsevier B.V. All rights reserved.

  6. East Asian SO2 pollution plume over Europe – Part 1: Airborne trace gas measurements and source identification by particle dispersion model simulations

    Directory of Open Access Journals (Sweden)

    A. Stohl

    2009-07-01

    Full Text Available A large SO2-rich pollution plume of East Asian origin was detected by aircraft based CIMS (Chemical Ionization Mass Spectrometry measurements at 3–7.5 km altitude over the North Atlantic. The measurements, which took place on 3 May 2006 aboard of the German research aircraft Falcon, were part of the INTEX-B (Intercontinental Chemical Transport Experiment-B campaign. Additional trace gases (NO, NOy, CO, H2O were measured and used for comparison and source identification. The atmospheric SO2 mole fraction was markedly increased inside the plume and reached up to 900 pmol/mol. Accompanying lagrangian FLEXPART particle dispersion model simulations indicate that the probed pollution plume originated at low altitudes from densely populated and industrialized regions of East Asia, primarily China, about 8–12 days prior to the measurements.

  7. Twitter as a Potential Disaster Risk Reduction Tool. Part II: Descriptive Analysis of Identified Twitter Activity during the 2013 Hattiesburg F4 Tornado.

    Science.gov (United States)

    Cooper, Guy Paul; Yeager, Violet; Burkle, Frederick M; Subbarao, Italo

    2015-06-29

    This article describes a novel triangulation methodological approach for identifying twitter activity of regional active twitter users during the 2013 Hattiesburg EF-4 Tornado. A data extraction and geographically centered filtration approach was utilized to generate Twitter data for 48 hrs pre- and post-Tornado. The data was further validated using six sigma approach utilizing GPS data. The regional analysis revealed a total of 81,441 tweets, 10,646 Twitter users, 27,309 retweets and 2637 tweets with GPS coordinates. Twitter tweet activity increased 5 fold during the response to the Hattiesburg Tornado.  Retweeting activity increased 2.2 fold. Tweets with a hashtag increased 1.4 fold. Twitter was an effective disaster risk reduction tool for the Hattiesburg EF-4 Tornado 2013.

  8. Catalytic conversion of CO, NO and SO2 on supported sulfide catalysts. Part 2. Catalytic reduction of NO and SO2 by CO

    International Nuclear Information System (INIS)

    Zhuang, S.-X.; Yamazaki, M.; Omata, K.; Takahashi, Y.; Yamada, M.

    2001-01-01

    To investigate the possibility of simultaneous catalytic reduction of NO and SO 2 by CO, reactions of NO, NO-CO, and NO-SO 2 -CO were performed on γ-alumina-supported sulfides of transition metals including Co, Mo, CoMo and FeMo. NO was decomposed into N 2 O and N 2 accompanied with the formation of SO 2 ; this serious oxidation of lattice sulfur resulted in the deactivation of the catalysts. The addition of CO to the NO stream suppressed SO 2 formation and yielded COS instead. A stoichiometric conversion of NO and CO to N 2 and CO 2 was observed above 350C on the CoMo and the FeMo catalysts. Although the CO addition lengthened catalyst life, it was not enough to maintain activity. After the NO-CO reaction, an XPS analysis showed the growth of Mo 6+ and SO 4 2- peaks, especially for the sulfided FeMo/Al 2 O 3 ; the FeMo catalyst underwent strong oxidation in the NO-CO reaction. The NO and the NO-CO reactions proceeded non-catalytically, consuming catalyst lattice sulfur to yield SO 2 or COS. The addition of SO 2 in the NO-CO system enabled in situ regeneration of the catalysts; the catalysts oxidized through abstraction of lattice sulfur experienced anew reduction and sulfurization through the SO 2 -CO reaction at higher temperature. NO and SO 2 were completely and catalytically converted at 400C on the sulfided CoMo/Al 2 O 3 . By contrast, the sulfided FeMo/Al 2 O 3 was easily oxidized by NO and hardly re-sulfided under the test conditions. Oxidation states of the metals before and after the reactions were determined. Silica and titania-supported CoMo catalysts were also evaluated to study support effects

  9. Determining Mass and Persistence of a Reactive Brominated-Solvent DNAPL Source Using Mass Depletion-Mass Flux Reduction Relationships During Pumping

    Science.gov (United States)

    Johnston, C. D.; Davis, G. B.; Bastow, T.; Annable, M. D.; Trefry, M. G.; Furness, A.; Geste, Y.; Woodbury, R.; Rhodes, S.

    2011-12-01

    Measures of the source mass and depletion characteristics of recalcitrant dense non-aqueous phase liquid (DNAPL) contaminants are critical elements for assessing performance of remediation efforts. This is in addition to understanding the relationships between source mass depletion and changes to dissolved contaminant concentration and mass flux in groundwater. Here we present results of applying analytical source-depletion concepts to pumping from within the DNAPL source zone of a 10-m thick heterogeneous layered aquifer to estimate the original source mass and characterise the time trajectory of source depletion and mass flux in groundwater. The multi-component, reactive DNAPL source consisted of the brominated solvent tetrabromoethane (TBA) and its transformation products (mostly tribromoethene - TriBE). Coring and multi-level groundwater sampling indicated the DNAPL to be mainly in lower-permeability layers, suggesting the source had already undergone appreciable depletion. Four simplified source dissolution models (exponential, power function, error function and rational mass) were able to describe the concentration history of the total molar concentration of brominated organics in extracted groundwater during 285 days of pumping. Approximately 152 kg of brominated compounds were extracted. The lack of significant kinetic mass transfer limitations in pumped concentrations was notable. This was despite the heterogeneous layering in the aquifer and distribution of DNAPL. There was little to choose between the model fits to pumped concentration time series. The variance of groundwater velocities in the aquifer determined during a partitioning inter-well tracer test (PITT) were used to parameterise the models. However, the models were found to be relatively insensitive to this parameter. All models indicated an initial source mass around 250 kg which compared favourably to an estimate of 220 kg derived from the PITT. The extrapolated concentrations from the

  10. Reduction of LNG FOB cost

    International Nuclear Information System (INIS)

    Aoki, Ichizo; Kikkawa, Yoshitsugi

    1997-01-01

    To achieve a competitive LNG price for the consumers against other energy sources, reduction of LNG FOB (Free on Board) cost i.e. LNG cost at LNG ship flange, will be the key item. It is necessary to perform a many optimization studies (or value engineering) for each stage of the LNG project. These stages are: Feasibility study; Conceptual design - FEED (Front End Engineering and Design); EPC (Engineering, Procurement and Construction); Operation and maintenance. Since the LNG plant forms one part of the LNG chain, starting from gas production to LNG receiving, and requires several billion US dollar of investment, the consequences of a plant shut down on the LNG chain are clear, it is, therefore, important to get high availability which will also contribute the reduction of LNG FOB cost. (au) 25 refs

  11. Effect of pre-entry instruction as an additional part of radiation training beginner's course on reduction of radioactive contamination in two independent unsealed radioisotope facilities

    International Nuclear Information System (INIS)

    Matsuda, Naoki; Yoshida, Masahiro; Takao, Hideaki; Kaneko, Mamoru; Okumura, Yutaka; Shimasaki, Tatsuya; Kojima, Akihiro; Shiraishi, Yoshioki; Horiuchi, Seikoh

    2005-01-01

    The education for radiation workers is essential for the safety of radiation facility that stands on radiation protection practice by each worker. Japanese laws concerning radiation safety requires each radiation worker attending the 6 hours beginner's training course before entering the control area. However, in unsealed radioisotope facilities, radioactive contaminations in the control area may still take place because practical procedures for radiation safety vary depending on the type of experiments and the characteristics of radioisotopes. Therefore, an additional and practical training for each radiation worker is needed. In an attempt to give the workers an additional training of this kind, the pre-entry instruction was performed independently in Center for Frontier Life Sciences, Nagasaki University and in Institute of Resource Development and Analysis Kumamoto University. In this study, the efficacy of the instruction in each facility was assessed quantitatively on the basis of the incidence of contamination in the control area. The instruction covered laboratory rules, radioisotope ordering information, description of sign-up sheets, radioactive waste management, use of survey meters, and lab tour with an appropriate modification to meet with a specificity of each experiment. The instruction was given to beginners and to refreshers who have not handled radioisotopes for a long period, in a face-to-face manner for 1 hour before they start working radioisotopes. To examine the education effect on the reduction of contamination in a typical and frequently used laboratory, the contamination in molecular biology room of Nagasaki University was surveyed directly by a GM survey meter on a daily basis. In Kumamoto University, contamination on the surface of the entire floor in the control area was surveyed monthly by the smear method to know the education effect on general reduction of contamination. The results revealed that the number of contamination decreased

  12. A Two-Microphone Noise Reduction System for Cochlear Implant Users with Nearby Microphones—Part II: Performance Evaluation

    Directory of Open Access Journals (Sweden)

    Rudolf Häusler

    2008-06-01

    Full Text Available Users of cochlear implants (auditory aids, which stimulate the auditory nerve electrically at the inner ear often suffer from poor speech understanding in noise. We evaluate a small (intermicrophone distance 7 mm and computationally inexpensive adaptive noise reduction system suitable for behind-the-ear cochlear implant speech processors. The system is evaluated in simulated and real, anechoic and reverberant environments. Results from simulations show improvements of 3.4 to 9.3 dB in signal to noise ratio for rooms with realistic reverberation and more than 18 dB under anechoic conditions. Speech understanding in noise is measured in 6 adult cochlear implant users in a reverberant room, showing average improvements of 7.9–9.6 dB, when compared to a single omnidirectional microphone or 1.3–5.6 dB, when compared to a simple directional two-microphone device. Subjective evaluation in a cafeteria at lunchtime shows a preference of the cochlear implant users for the evaluated device in terms of speech understanding and sound quality.

  13. Pediatric CT dose reduction for suspected appendicitis: a practice quality improvement project using artificial Gaussian noise--part 1, computer simulations.

    Science.gov (United States)

    Callahan, Michael J; Kleinman, Patricia L; Strauss, Keith J; Bandos, Andriy; Taylor, George A; Tsai, Andy; Kleinman, Paul K

    2015-01-01

    The purpose of this study was to develop a departmental practice quality improvement project to systematically reduce CT doses for the evaluation of suspected pediatric appendicitis by introducing computer-generated gaussian noise. Two hundred MDCT abdominopelvic examinations of patients younger than 20 years performed with girth-based scanning parameters for suspected appendicitis were reviewed. Two judges selected 45 examinations in which the diagnosis of appendicitis was excluded (14, appendix not visualized; 31, normal appendix visualized). Gaussian noise was introduced into axial image series, creating five additional series acquired at 25-76% of the original dose. Two readers reviewed 270 image series for appendix visualization (4-point Likert scale and arrow localization). Volume CT dose index (CTDIvol) and size-specific dose estimate (SSDE) were calculated by use of patient girth. Confidence ratings and localization accuracy were analyzed with mixed models and nonparametric bootstrap analysis at a 0.05 significance level. The mean baseline SSDE for the 45 patients was 16 mGy (95% CI, 12-20 mGy), and the corresponding CTDIvol was 10 mGy (95% CI, 4-16 mGy). Changes in correct appendix localization frequencies were minor. There was no substantial trend with decreasing simulated dose level (p = 0.46). Confidence ratings decreased with increasing dose reduction (p = 0.007). The average decreases were -0.27 for the 25% simulated dose (p = 0.01), -0.17 for 33% (p = 0.03), and -0.03 for 43% (p = 0.65). Pediatric abdominal MDCT can be performed with 43% of the original dose (SSDE, 7 mGy; CTDIvol, 4.3 mGy) without substantially affecting visualization of a normal appendix.

  14. Using δ15N of Chironomidae as an index of nitrogen sources and processing within watersheds as part of EPA's National Aquatic Resource Surveys

    Science.gov (United States)

    Brooks, J. R.; Compton, J.; Herlihy, A.; Sobota, D. J.; Stoddard, J.; Weber, M.

    2014-12-01

    Nitrogen (N) removal in watersheds is an important regulating ecosystem service that can help reduce N pollution in the nation's waterways. However, processes that remove N such as denitrification are generally determined at point locations. Measures that integrate N processing within watersheds and over time would be particularly useful for assessing the degree of this vital service. Because most N removal processes isotopically enrich the N remaining, δ15N from basal food-chain organisms in aquatic ecosystems can provide information on watershed N processing. As part of EPA's National Aquatic Resource Surveys (NARS), we measured δ15N of Chironomidae in lakes, rivers and streams because these larval aquatic insects were found in abundance in almost every lake and stream in the U.S. Using information on nitrogen loading to the watershed, and total N concentrations within the water, we assessed when elevated chironomid δ15N would indicate N removal rather than possible enriched sources of N. Chironomid δ15N values ranged from -4 to +20 ‰, and were higher in rivers and streams than in lakes (median = 7.6 ‰ vs. 4.8 ‰, respectively), indicating that N was processed to a greater degree in lotic chironomids than in lentic ones. For both, δ15N increased with watershed-level agricultural land cover and N loading, and decreased as precipitation increased. In rivers and streams with high synthetic N loading, we found lower N concentrations in streams with higher chironomid δ15N values, suggesting greater N removal. At low levels of synthetic N loading, the pattern reversed, and streams with enriched chironomid δ15N had higher N concentrations, suggesting enriched sources such as manure or sewage. Our results indicate that chironomid δ15N values can provide valuable information about watershed-level N inputs and processing for national water quality monitoring efforts.

  15. Use of Oil Palm Waste as a Renewable Energy Source and Its Impact on Reduction of Air Pollution in Context of Malaysia

    International Nuclear Information System (INIS)

    Begum, Shahida; Kumaran P; Jayakumar M

    2013-01-01

    One of the most efficient and effective solutions for sustainable energy supply to supplement the increasing energy demand and reducing environment pollution is renewable energy resources. Malaysia is currently the world's second largest producer and exporter of palm oil and 47% of the world's supply of palm oil is produced by this country. Nearly 80 million tonnes of Fresh Fruit Bunches (FFB) are processed annually in 406 palm oil mills and are generating approximately 54 million tonnes of palm oil mill effluent (POME), known to generate biogas consisting of methane – a Green House Gas (GHG) identifiable to cause global warming. This is 21 times more potent GHG than CO 2 . These two major oil palm wastes are a viable renewable energy (RE) source for production of electricity. If the two sources are used in harnessing the renewable energy potential the pollution intensity from usage of non-renewable sources can also be reduced significantly. This study focused on the pollution mitigation potential of biogas as biogas is a renewable energy. Utilization of this renewable source for the production of electricity is believed to reduce GHG emissions to the atmosphere.

  16. Use of Oil Palm Waste as a Renewable Energy Source and Its Impact on Reduction of Air Pollution in Context of Malaysia

    Science.gov (United States)

    Begum, Shahida; P, Kumaran; M, Jayakumar

    2013-06-01

    One of the most efficient and effective solutions for sustainable energy supply to supplement the increasing energy demand and reducing environment pollution is renewable energy resources. Malaysia is currently the world's second largest producer and exporter of palm oil and 47% of the world's supply of palm oil is produced by this country. Nearly 80 million tonnes of Fresh Fruit Bunches (FFB) are processed annually in 406 palm oil mills and are generating approximately 54 million tonnes of palm oil mill effluent (POME), known to generate biogas consisting of methane - a Green House Gas (GHG) identifiable to cause global warming. This is 21 times more potent GHG than CO2. These two major oil palm wastes are a viable renewable energy (RE) source for production of electricity. If the two sources are used in harnessing the renewable energy potential the pollution intensity from usage of non-renewable sources can also be reduced significantly. This study focused on the pollution mitigation potential of biogas as biogas is a renewable energy. Utilization of this renewable source for the production of electricity is believed to reduce GHG emissions to the atmosphere.

  17. Origin of acid orthoderived and paraderived geologic formations of the central part of the province of Limousin (France). A possible source for uraniferous leucogranite

    International Nuclear Information System (INIS)

    Bourguignon, A.

    1988-01-01

    Important metamorphic formations of the central part of the province of Limousin are studied by chemical investigations for characterization of their primary signature. Four large orthoderived formations are compared: Dronne, Meuzac, and Thaurion arcs and leptynite formations. The typology of the parent magmatism of orthogneiss and leptynite allows to find leack most of plutonic associations known in the Variscan chain (subalkaline, calcoalkaline, aluminous). Interpretation of primary geochemical fractionation in rocks from the Dronne are suggests cogenetism of the whole facies following a fractionated crystallization process. Moreover rocks from the Dronne arc have a peraluminous character with high U and Th content related to subalkaline magmatism which make of them a potential source of uraniferous peraluminous leucogranites. Paraderived formations are represented by 3 mica schist formations and 2 gneiss formations. Each unit is individualized by geochemical study of mica schist. Gneiss formation are chemically distinct. These differences confirm that they belong to distinct lithologic units. Trace elements are used to precise the paleogeotectonic context of original sediment deposition [fr

  18. Reductive de-polymerization of kraft lignin for chemicals and fuels using formic acid as an in-situ hydrogen source.

    Science.gov (United States)

    Huang, Shanhua; Mahmood, Nubla; Tymchyshyn, Matthew; Yuan, Zhongshun; Xu, Chunbao Charles

    2014-11-01

    In this study, formic acid (FA) was employed as an in-situ hydrogen donor for the reductive de-polymerization of kraft lignin (KL). Under the optimum operating conditions, i.e., 300 °C, 1 h, 18.6 wt.% substrate concentration, 50/50 (v/v) water-ethanol medium with FA at a FA-to-lignin mass ratio of 0.7, KL (Mw∼10,000 g/mol) was effectively de-polymerized, producing de-polymerized lignin (DL, Mw 1270 g/mol) at a yield of ∼90 wt.% and polymerization of KL. Copyright © 2014 Elsevier Ltd. All rights reserved.

  19. Reduction redux.

    Science.gov (United States)

    Shapiro, Lawrence

    2018-04-01

    Putnam's criticisms of the identity theory attack a straw man. Fodor's criticisms of reduction attack a straw man. Properly interpreted, Nagel offered a conception of reduction that captures everything a physicalist could want. I update Nagel, introducing the idea of overlap, and show why multiple realization poses no challenge to reduction so construed. Copyright © 2017 Elsevier Ltd. All rights reserved.

  20. Contrast source inversion (CSI) method to cross-hole radio-imaging (RIM) data - Part 2: A complex synthetic example and a case study

    Science.gov (United States)

    Li, Yongxing; Smith, Richard S.

    2018-03-01

    We present two examples of using the contrast source inversion (CSI) method to invert synthetic radio-imaging (RIM) data and field data. The synthetic model has two isolated conductors (one perfect conductor and one moderate conductor) embedded in a layered background. After inversion, we can identify the two conductors on the inverted image. The shape of the perfect conductor is better resolved than the shape of the moderate conductor. The inverted conductivity values of the two conductors are approximately the same, which demonstrates that the conductivity values cannot be correctly interpreted from the CSI results. The boundaries and the tilts of the upper and the lower conductive layers on the background can also be inferred from the results, but the centre parts of conductive layers in the inversion results are more conductive than the parts close to the boreholes. We used the straight-ray tomographic imaging method and the CSI method to invert the RIM field data collected using the FARA system between two boreholes in a mining area in Sudbury, Canada. The RIM data include the amplitude and the phase data collected using three frequencies: 312.5 kHz, 625 kHz and 1250 kHz. The data close to the ground surface have high amplitude values and complicated phase fluctuations, which are inferred to be contaminated by the reflected or refracted electromagnetic (EM) fields from the ground surface, and are removed for all frequencies. Higher-frequency EM waves attenuate more quickly in the subsurface environment, and the locations where the measurements are dominated by noise are also removed. When the data are interpreted with the straight-ray method, the images differ substantially for different frequencies. In addition, there are some unexpected features in the images, which are difficult to interpret. Compared with the straight-ray imaging results, the inversion results with the CSI method are more consistent for different frequencies. On the basis of what we learnt

  1. Space Vector Modulation for DC-Link Current Ripple Reduction in Back-To-Back Current Source Converters for Microgrid Applications

    DEFF Research Database (Denmark)

    Guo, Xiaoqiang; Xu, David; Guerrero, Josep M.

    2015-01-01

    Back-to-back converters have been typically used to interconnect the microgrids. For a back-to-back current source converter, the dc-link current ripple is one of the important parameters. A large ripple will cause the electromagnetic interference, undesirable high-frequency losses, and system...... instability. Conventionally, with a given switching frequency and rated voltage, the current ripple can be reduced by increasing the dc-link inductor, but it leads to bulky size, high cost and slow dynamic response. In order to solve this problem, this paper reveals that the current ripple can...

  2. Change in the radiation dose at a point where an inhomogeneity partly covers the radiation field from a 60Co-γ-source

    International Nuclear Information System (INIS)

    Helmrot, E.

    1976-04-01

    Measurements and calculations have been made in order to study the change of the radiation dose in a point when an inhomogeneity covers parts of the radiation field from a Co 60-source. An ionization chamber, placed in a water phantom, was used for the measurements. As inhomogeneity an air cavity was used. The measuring point was placed on the central axis of the radiation field during the measurement. The air cavity was moved in front of the measuring point 0.5 - 1 cm by steps laterally, i.e. along a line perpendicular to the radiation direction. Measurements were made at different depths behind the air cavity. The air cavity was placed at different distances from the front plate of the water phantom. Measurements and calculations show that the change of the radiation dose, when the edge of the air cavity passes the measuring point, varies with the depth distance to the air cavity. The greatest deviation is near the air cavity and at a great distance behind this. The change of the radiation dose is less than 2 percent at distances greater than 2 cm from the edge of the air cavity laterally. This change is independent of the depth distance to the air cavity. The maximum deviation 1 cm from the edge of the air cavity is 5 percent independent of the distance tothe air cavity. Used methods of calculation can be extended to be used for irregular inhomogeneities but this requires knowledge of the three-dimensional extension of the inhomogeneity. (M.S.)

  3. Contrast volume reduction using third generation dual source computed tomography for the evaluation of patients prior to transcatheter aortic valve implantation

    Energy Technology Data Exchange (ETDEWEB)

    Bittner, Daniel O. [University Hospital Erlangen, Friedrich-Alexander University Erlangen-Nuernberg (FAU), Department of Internal Medicine 2 (Cardiology), Erlangen (Germany); Harvard Medical School, Cardiac MR PET CT Program, Massachusetts General Hospital, Boston, MA (United States); Arnold, Martin; Klinghammer, Lutz; Schuhbaeck, Annika; Hell, Michaela M.; Muschiol, Gerd; Gauss, Soeren; Achenbach, Stephan; Marwan, Mohamed [University Hospital Erlangen, Friedrich-Alexander University Erlangen-Nuernberg (FAU), Department of Internal Medicine 2 (Cardiology), Erlangen (Germany); Lell, Michael; Uder, Michael [University Hospital Erlangen, Friedrich-Alexander University Erlangen-Nuernberg (FAU), Department of Radiology, Erlangen (Germany); Hoffmann, Udo [Harvard Medical School, Cardiac MR PET CT Program, Massachusetts General Hospital, Boston, MA (United States)

    2016-12-15

    Chronic renal failure is common in patients referred for transcatheter aortic valve implantation (TAVI). CT angiography is recommended and provides crucial information prior to TAVI. We evaluated the feasibility of a reduced contrast volume protocol for pre-procedural CT imaging. Forty consecutive patients were examined with prospectively ECG-triggered high-pitch spiral acquisition using a novel third-generation dual-source CT system; 38 ml contrast agent was used. Image quality was graded on a visual scale (1-4). Contrast attenuation was measured at the level of the aortic root and at the iliac bifurcation. Mean patient age was 82 ± 6 years (23 males; 58 %). Mean attenuation/average image quality was 285 ± 60 HU/1.5 at the aortic annulus compared to 289 ± 74 HU/1.8 at the iliac bifurcation (p = 0.77/p = 0.29). Mean estimated effective radiation dose was 2.9 ± 0.3 mSv. A repeat acquisition was necessary in one patient due to image quality. Out of the 35 patients who underwent TAVI, 31 (89 %) patients had no or mild aortic regurgitation. Thirty-two (91 %) patients were discharged successfully. Pre-procedural CTA with a total of 38 ml contrast volume is feasible and clinically useful, using third-generation dual-source CT, allowing comprehensive imaging for procedural success. (orig.)

  4. Dose Reduction Techniques

    International Nuclear Information System (INIS)

    WAGGONER, L.O.

    2000-01-01

    As radiation safety specialists, one of the things we are required to do is evaluate tools, equipment, materials and work practices and decide whether the use of these products or work practices will reduce radiation dose or risk to the environment. There is a tendency for many workers that work with radioactive material to accomplish radiological work the same way they have always done it rather than look for new technology or change their work practices. New technology is being developed all the time that can make radiological work easier and result in less radiation dose to the worker or reduce the possibility that contamination will be spread to the environment. As we discuss the various tools and techniques that reduce radiation dose, keep in mind that the radiological controls should be reasonable. We can not always get the dose to zero, so we must try to accomplish the work efficiently and cost-effectively. There are times we may have to accept there is only so much you can do. The goal is to do the smart things that protect the worker but do not hinder him while the task is being accomplished. In addition, we should not demand that large amounts of money be spent for equipment that has marginal value in order to save a few millirem. We have broken the handout into sections that should simplify the presentation. Time, distance, shielding, and source reduction are methods used to reduce dose and are covered in Part I on work execution. We then look at operational considerations, radiological design parameters, and discuss the characteristics of personnel who deal with ALARA. This handout should give you an overview of what it takes to have an effective dose reduction program

  5. Dose Reduction Techniques

    Energy Technology Data Exchange (ETDEWEB)

    WAGGONER, L.O.

    2000-05-16

    As radiation safety specialists, one of the things we are required to do is evaluate tools, equipment, materials and work practices and decide whether the use of these products or work practices will reduce radiation dose or risk to the environment. There is a tendency for many workers that work with radioactive material to accomplish radiological work the same way they have always done it rather than look for new technology or change their work practices. New technology is being developed all the time that can make radiological work easier and result in less radiation dose to the worker or reduce the possibility that contamination will be spread to the environment. As we discuss the various tools and techniques that reduce radiation dose, keep in mind that the radiological controls should be reasonable. We can not always get the dose to zero, so we must try to accomplish the work efficiently and cost-effectively. There are times we may have to accept there is only so much you can do. The goal is to do the smart things that protect the worker but do not hinder him while the task is being accomplished. In addition, we should not demand that large amounts of money be spent for equipment that has marginal value in order to save a few millirem. We have broken the handout into sections that should simplify the presentation. Time, distance, shielding, and source reduction are methods used to reduce dose and are covered in Part I on work execution. We then look at operational considerations, radiological design parameters, and discuss the characteristics of personnel who deal with ALARA. This handout should give you an overview of what it takes to have an effective dose reduction program.

  6. The search for geologic evidence of distant-source tsunamis using new field data in California: Chapter C in The SAFRR (Science Application for Risk Reduction) Tsunami Scenario

    Science.gov (United States)

    Wilson, Rick; Hemphill-Haley, Eileen; Jaffe, Bruce; Richmond, Bruce; Peters, Robert; Graehl, Nick; Kelsey, Harvey; Leeper, Robert; Watt, Steve; McGann, Mary; Hoirup, Don F.; Chagué-Goff, Catherine; Goff, James; Caldwell, Dylan; Loofbourrow, Casey

    2014-01-01

    A statewide assessment for geological evidence of tsunamis, primarily from distant-source events, found tsunami deposits at several locations, though evidence was absent at most locations evaluated. Several historical distant-source tsunamis, including the 1946 Aleutian, 1960 Chile, and 1964 Alaska events, caused inundation along portions of the northern and central California coast. Recent numerical tsunami modeling results identify the eastern Aleutian Islands subduction zone as the “worstcase” distant-source region, with the potential for causing tsunami runups of 7–10 m in northern and central California and 3–4 m in southern California. These model results, along with a review of historical topographic maps and past geotechnical evaluations, guided site selection for tsunami deposit surveys. A reconnaissance of 20 coastal marshlands was performed through site visits and coring of shallow surface sediments to determine if evidence for past tsunamis existed. Although conclusive evidence of tsunami deposits was not found at most of the sites evaluated, geologic evidence consistent with tsunami inundation was found at two locations: Three marshes in the Crescent City area and Pillar Point marsh near Half Moon Bay. Potential tsunami deposits were also evaluated at the Carpinteria Salt Marsh Reserve in Santa Barbara County. In Crescent City, deposits were ascribed to tsunamis on the basis of stratigraphic architecture, particle size, and microfossil content, and they were further assigned to the 1964 Alaska and 1700 Cascadia tsunamis on the basis of dating by cesium-137 and radiocarbon methods, respectively. The 1946 tsunami sand deposit was clearly identified throughout Pillar Point marsh, and one to two other similar but highly discontinuous sand layers were present within 0.5 m of the surface. A tsunami-origin interpretation for sand layers at Carpinteria is merely consistent with graded bedding and unsupported by diatom or foraminiferal assemblages

  7. Field-scale evaluation of biological uranium reduction and reoxidation in the near-source zone at the NABIR Field Research Center in Oak Ridge, TN

    International Nuclear Information System (INIS)

    Craig S. Criddle; Peter Kitanidis; Scott Fendorf; Weimin Wu; Philip M. Jardine; Jizhong Zhou; Baohua Gu

    2006-01-01

    The primary objective of the project is to advance the understanding and predictive capability of coupled hydrological, geochemical, and microbiological processes that control the in situ transport and bioremediation radionuclides and co-contaminants at multiple scales. Specific objectives include: (1) Investigate the feasibility of in situ bioremediation of uranium in a highly contaminated region within the subsurface of Area 3 of the DoE ERSP FRC (2) Using a variety of tracer strategies, develop and model a system that establishes hydraulic control of the target region for biostimulation (3) Perform long term in situ biostimulation studies that create a microbial communities capable of reducing residual nitrate to N2 and mobile U(VI) to sparingly soluble U(IV) (4) Use a variety of solid and solution phase interrogation techniques to quantify the extent of in situ reduction and immobilization of U(VI). (5) Investigate a variety of geochemical factors that influence the stability and possible reoxidation of reduced uranium

  8. Reduction of thoracic aorta motion artifact with high-pitch 128-slice dual-source computed tomographic angiography: a historical control study.

    Science.gov (United States)

    Nakagawa, Junichiro; Tasaki, Osamu; Watanabe, Yoshiyuki; Azuma, Takeo; Ohnishi, Mitsuo; Ukai, Isao; Tahara, Kenichi; Ogura, Hiroshi; Kuwagata, Yasuyuki; Hamasaki, Toshimitsu; Shimazu, Takeshi

    2013-01-01

    Electrocardiogram-gated imaging combined with multi-detector row computed tomography (MDCT) has reduced cardiac motion artifacts, but it was not practical in the emergency setting. The purpose of this study was to evaluate the ability of a high-pitch, 128-slice dual-source CT (DSCT) scanner to reduce motion artifacts in patients admitted to the emergency room. This study comprised 100 patients suspected of having thoracic aorta lesions. We examined 47 patients with the 128-slice DSCT scanner (DSCT group), and 53 patients were examined with a 64-slice MDCT scanner (MDCT group). Six anatomic areas in the thoracic aorta were evaluated. Computed tomography images in the DSCT group were distinct, and significant differences were observed in images of all areas between the 2 groups except for the descending aorta. The high-pitch DSCT scanner can reduce motion artifacts of the thoracic aorta and enable radiological diagnosis even in patients with tachycardia and without breath hold.

  9. Alcohol harm reduction in Europe

    DEFF Research Database (Denmark)

    Herring, Rachel; Betsy, Thom; Beccaria, Franca

    2010-01-01

    The EMCDDA’s 10th scientific monograph, entitled Harm reduction: evidence, impacts and challenges provides a comprehensive overview of the harm reduction field. Part I of the monograph looks back at the emergence of harm reduction approaches and their diffusion, and explores the concept from diff...

  10. Potential for waste reduction

    International Nuclear Information System (INIS)

    Warren, J.L.

    1990-01-01

    The author focuses on wastes considered hazardous under the Resource Conservation and Recovery Act. This chapter discusses wastes that are of interest as well as the factors affecting the quantity of waste considered available for waste reduction. Estimates are provided of the quantities of wastes generated. Estimates of the potential for waste reduction are meaningful only to the extent that one can understand the amount of waste actually being generated. Estimates of waste reduction potential are summarized from a variety of government and nongovernment sources

  11. Collecting Evidence to Inform Salt Reduction Policies in Argentina: Identifying Sources of Sodium Intake in Adults from a Population-Based Sample

    Directory of Open Access Journals (Sweden)

    Natalia Elorriaga

    2017-08-01

    Full Text Available The maximum content of sodium in selected processed foods (PF in Argentina was limited by a law enacted in 2013. Data about intake of these and other foods are necessary for policy planning, implementation, evaluation, and monitoring. We examined data from the CESCAS I population-based cohort study to assess the main dietary sources among PF and frequency of discretionary salt use by sex, age, and education attainment, before full implementation of the regulations in 2015. We used a validated 34-item FFQ (Food Frequency Questionnaire to assess PF intake and discretional salt use. Among 2127 adults in two Argentinean cities, aged 35–76 years, mean salt intake from selected PFs was 4.7 g/day, higher among male and low education subgroups. Categories of foods with regulated maximum limits provided near half of the sodium intake from PFs. Use of salt (always/often at the table and during cooking was reported by 9% and 73% of the population, respectively, with higher proportions among young people. Reducing salt consumption to the target of 5 g/day may require adjustments to the current regulation (reducing targets, including other food categories, as well as reinforcing strategies such as education campaigns, labeling, and voluntary agreement with bakeries.

  12. Robust methods for data reduction

    CERN Document Server

    Farcomeni, Alessio

    2015-01-01

    Robust Methods for Data Reduction gives a non-technical overview of robust data reduction techniques, encouraging the use of these important and useful methods in practical applications. The main areas covered include principal components analysis, sparse principal component analysis, canonical correlation analysis, factor analysis, clustering, double clustering, and discriminant analysis.The first part of the book illustrates how dimension reduction techniques synthesize available information by reducing the dimensionality of the data. The second part focuses on cluster and discriminant analy

  13. Automated tube voltage selection for radiation dose and contrast medium reduction at coronary CT angiography using 3{sup rd} generation dual-source CT

    Energy Technology Data Exchange (ETDEWEB)

    Mangold, Stefanie [Medical University of South Carolina, Division of Cardiovascular Imaging, Department of Radiology and Radiological Science, Charleston, SC (United States); Eberhard-Karls University Tuebingen, Department of Diagnostic and Interventional Radiology, Tuebingen (Germany); Wichmann, Julian L. [Medical University of South Carolina, Division of Cardiovascular Imaging, Department of Radiology and Radiological Science, Charleston, SC (United States); University Hospital Frankfurt, Department of Diagnostic and Interventional Radiology, Frankfurt (Germany); Schoepf, U.J. [Medical University of South Carolina, Division of Cardiovascular Imaging, Department of Radiology and Radiological Science, Charleston, SC (United States); Medical University of South Carolina, Division of Cardiology, Department of Medicine, Charleston, SC (United States); Poole, Zachary B.; Varga-Szemes, Akos; De Cecco, Carlo N. [Medical University of South Carolina, Division of Cardiovascular Imaging, Department of Radiology and Radiological Science, Charleston, SC (United States); Canstein, Christian [Siemens Medical Solutions, Malvern, PA (United States); Caruso, Damiano [Medical University of South Carolina, Division of Cardiovascular Imaging, Department of Radiology and Radiological Science, Charleston, SC (United States); University of Rome ' ' Sapienza' ' , Department of Radiological Sciences, Oncology and Pathology, Rome (Italy); Bamberg, Fabian; Nikolaou, Konstantin [Eberhard-Karls University Tuebingen, Department of Diagnostic and Interventional Radiology, Tuebingen (Germany)

    2016-10-15

    To investigate the relationship between automated tube voltage selection (ATVS) and body mass index (BMI) and its effect on image quality and radiation dose of coronary CT angiography (CCTA). We evaluated 272 patients who underwent CCTA with 3{sup rd} generation dual-source CT (DSCT). Prospectively ECG-triggered spiral acquisition was performed with automated tube current selection and advanced iterative reconstruction. Tube voltages were selected by ATVS (70-120 kV). BMI, effective dose (ED), and vascular attenuation in the coronary arteries were recorded. Signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR) were calculated. Five-point scales were used for subjective image quality analysis. Image quality was rated good to excellent in 98.9 % of examinations without significant differences for proximal and distal attenuation (all p ≥.0516), whereas image noise was rated significantly higher at 70 kV compared to ≥100 kV (all p <.0266). However, no significant differences were observed in SNR or CNR at 70-120 kV (all p ≥.0829). Mean ED at 70-120 kV was 1.5 ± 1.2 mSv, 2.4 ± 1.5 mSv, 3.6 ± 2.7 mSv, 5.9 ± 4.0 mSv, 7.9 ± 4.2 mSv, and 10.7 ± 4.1 mSv, respectively (all p ≤.0414). Correlation analysis showed a moderate association between tube voltage and BMI (r =.639). ATVS allows individual tube voltage adaptation for CCTA performed with 3{sup rd} generation DSCT, resulting in significantly decreased radiation exposure while maintaining image quality. (orig.)

  14. Part 2. Development of Enhanced Statistical Methods for Assessing Health Effects Associated with an Unknown Number of Major Sources of Multiple Air Pollutants.

    Science.gov (United States)

    Park, Eun Sug; Symanski, Elaine; Han, Daikwon; Spiegelman, Clifford

    2015-06-01

    A major difficulty with assessing source-specific health effects is that source-specific exposures cannot be measured directly; rather, they need to be estimated by a source-apportionment method such as multivariate receptor modeling. The uncertainty in source apportionment (uncertainty in source-specific exposure estimates and model uncertainty due to the unknown number of sources and identifiability conditions) has been largely ignored in previous studies. Also, spatial dependence of multipollutant data collected from multiple monitoring sites has not yet been incorporated into multivariate receptor modeling. The objectives of this project are (1) to develop a multipollutant approach that incorporates both sources of uncertainty in source-apportionment into the assessment of source-specific health effects and (2) to develop enhanced multivariate receptor models that can account for spatial correlations in the multipollutant data collected from multiple sites. We employed a Bayesian hierarchical modeling framework consisting of multivariate receptor models, health-effects models, and a hierarchical model on latent source contributions. For the health model, we focused on the time-series design in this project. Each combination of number of sources and identifiability conditions (additional constraints on model parameters) defines a different model. We built a set of plausible models with extensive exploratory data analyses and with information from previous studies, and then computed posterior model probability to estimate model uncertainty. Parameter estimation and model uncertainty estimation were implemented simultaneously by Markov chain Monte Carlo (MCMC*) methods. We validated the methods using simulated data. We illustrated the methods using PM2.5 (particulate matter ≤ 2.5 μm in aerodynamic diameter) speciation data and mortality data from Phoenix, Arizona, and Houston, Texas. The Phoenix data included counts of cardiovascular deaths and daily PM2

  15. Long-term particulate matter modeling for health effect studies in California - Part 2: Concentrations and sources of ultrafine organic aerosols

    Science.gov (United States)

    Hu, Jianlin; Jathar, Shantanu; Zhang, Hongliang; Ying, Qi; Chen, Shu-Hua; Cappa, Christopher D.; Kleeman, Michael J.

    2017-04-01

    Organic aerosol (OA) is a major constituent of ultrafine particulate matter (PM0. 1). Recent epidemiological studies have identified associations between PM0. 1 OA and premature mortality and low birth weight. In this study, the source-oriented UCD/CIT model was used to simulate the concentrations and sources of primary organic aerosols (POA) and secondary organic aerosols (SOA) in PM0. 1 in California for a 9-year (2000-2008) modeling period with 4 km horizontal resolution to provide more insights about PM0. 1 OA for health effect studies. As a related quality control, predicted monthly average concentrations of fine particulate matter (PM2. 5) total organic carbon at six major urban sites had mean fractional bias of -0.31 to 0.19 and mean fractional errors of 0.4 to 0.59. The predicted ratio of PM2. 5 SOA / OA was lower than estimates derived from chemical mass balance (CMB) calculations by a factor of 2-3, which suggests the potential effects of processes such as POA volatility, additional SOA formation mechanism, and missing sources. OA in PM0. 1, the focus size fraction of this study, is dominated by POA. Wood smoke is found to be the single biggest source of PM0. 1 OA in winter in California, while meat cooking, mobile emissions (gasoline and diesel engines), and other anthropogenic sources (mainly solvent usage and waste disposal) are the most important sources in summer. Biogenic emissions are predicted to be the largest PM0. 1 SOA source, followed by mobile sources and other anthropogenic sources, but these rankings are sensitive to the SOA model used in the calculation. Air pollution control programs aiming to reduce the PM0. 1 OA concentrations should consider controlling solvent usage, waste disposal, and mobile emissions in California, but these findings should be revisited after the latest science is incorporated into the SOA exposure calculations. The spatial distributions of SOA associated with different sources are not sensitive to the choice of

  16. Electrochemical quartz crystal microbalance analysis of the oxygen reduction reaction on Pt-based electrodes. Part 2: adsorption of oxygen species and ClO4(-) anions on Pt and Pt-Co alloy in HClO4 solutions.

    Science.gov (United States)

    Omura, J; Yano, H; Tryk, D A; Watanabe, M; Uchida, H

    2014-01-14

    To gain deeper insight into the role of adsorbed oxygenated species in the O2 reduction reaction (ORR) kinetics on platinum and platinum-cobalt alloys for fuel cells, we carried out a series of measurements with the electrochemical quartz crystal microbalance (EQCM) and the rotating disk electrode (RDE) in acid solution. The effects of anion adsorption on the activities for the ORR were first assessed in HClO4 and HF electrolyte solutions at various concentrations. In our previous work (Part 1), we reported that the perchlorate anion adsorbs specifically on bulk-Pt, with a Frumkin-Temkin isotherm, that is, a linear relationship between Δm and log[HClO4]. Here, we find that the specific adsorption on the Pt-skin/Pt3Co alloy was significantly stronger than that on bulk-Pt, in line with its modified electronic properties. The kinetically controlled current density j(k) for the O2 reduction at the Pt-skin/Pt3Co-RDE was about 9 times larger than that of the bulk-Pt-RDE in 0.01 M HClO4 saturated with air, but the j(k) values on Pt-skin/Pt3Co decreased with increasing [HClO4] more steeply than in the case of Pt, due to the blocking of the active sites by the specifically adsorbed ClO4(-). We have detected reversible mass changes for one or more adsorbed oxygen-containing species (Ox = O2, O, OH, H2O) on the Pt-skin/Pt3Co-EQCM and Pt-EQCM in O2-saturated and He-purged 0.01 M HClO4 solutions, in which the specific adsorption of ClO4(-) anions was negligible. The coverages of oxygen species θ(Ox) on the Pt-skin/Pt3Co in the potential range from 0.86 to 0.96 V in the O2-saturated solution were found to be larger than those on pure Pt, providing strong evidence that the higher O2 reduction activity on the Pt3Co is correlated with higher θ(Ox), contrary to the conventional view.

  17. Diagnostic Performance of an Advanced Modeled Iterative Reconstruction Algorithm for Low-Contrast Detectability with a Third-Generation Dual-Source Multidetector CT Scanner: Potential for Radiation Dose Reduction in a Multireader Study.

    Science.gov (United States)

    Solomon, Justin; Mileto, Achille; Ramirez-Giraldo, Juan Carlos; Samei, Ehsan

    2015-06-01

    To assess the effect of radiation dose reduction on low-contrast detectability by using an advanced modeled iterative reconstruction (ADMIRE; Siemens Healthcare, Forchheim, Germany) algorithm in a contrast-detail phantom with a third-generation dual-source multidetector computed tomography (CT) scanner. A proprietary phantom with a range of low-contrast cylindrical objects, representing five contrast levels (range, 5-20 HU) and three sizes (range, 2-6 mm) was fabricated with a three-dimensional printer and imaged with a third-generation dual-source CT scanner at various radiation dose index levels (range, 0.74-5.8 mGy). Image data sets were reconstructed by using different section thicknesses (range, 0.6-5.0 mm) and reconstruction algorithms (filtered back projection [FBP] and ADMIRE with a strength range of three to five). Eleven independent readers blinded to technique and reconstruction method assessed all data sets in two reading sessions by measuring detection accuracy with a two-alternative forced choice approach (first session) and by scoring the total number of visible object groups (second session). Dose reduction potentials based on both reading sessions were estimated. Results between FBP and ADMIRE were compared by using both paired t tests and analysis of variance tests at the 95% significance level. During the first session, detection accuracy increased with increasing contrast, size, and dose index (diagnostic accuracy range, 50%-87%; interobserver variability, ±7%). When compared with FBP, ADMIRE improved detection accuracy by 5.2% on average across the investigated variables (P material is available for this article. RSNA, 2015

  18. Selection of effective macroalgal species and tracing nitrogen sources on the different part of Yantai coast, China indicated by macroalgal δ{sup 15}N values

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yujue [Key Laboratory of Coastal Environmental Processes and Ecological Remediation, Yantai Institute of Coastal Zone Research, Chinese Academy of Sciences, Yantai, Shandong 264003 (China); Liu, Dongyan, E-mail: dyliu@yic.ac.cn [Key Laboratory of Coastal Environmental Processes and Ecological Remediation, Yantai Institute of Coastal Zone Research, Chinese Academy of Sciences, Yantai, Shandong 264003 (China); Richard, Pierre [Littoral, Environnement et Sociétés, UMR 7266 CNRS-Université de La Rochelle, 2 rue Olympe de Gouges, 17000 La Rochelle (France); Di, Baoping [Key Laboratory of Coastal Environmental Processes and Ecological Remediation, Yantai Institute of Coastal Zone Research, Chinese Academy of Sciences, Yantai, Shandong 264003 (China)

    2016-01-15

    To determine the dominant nitrogen sources and select effective macroalgal species for monitoring eutrophication along the Yantai coast, the total carbon (TOC), total nitrogen (TN) and nitrogen stable isotope ratio (δ{sup 15}N) in macroalgal tissue were analyzed in conjunction with environmental variables in seawater along the Yantai coastline. The ranges of macroalgal tissue δ{sup 15}N values together with dissolved inorganic nitrogen (DIN) composition indicated that except for the atmospheric deposition, there were three dominant types of nitrogen sources along the Yantai coast, with the agricultural fertilizer usage and factorial wastewater input at the S1 (Zhifu Island coast), the sewage discharge at S2 (the Moon Bay coast), the sewage discharge together with aquaculture impacts at S3 (Fisherman Wharf coast) and S4 (the Horse Island coast). Macroalgal growth were not limited by DIN but limited by P at S2, S3 and S4. Macroalgal species suitable or not for DIN source tracing along the Yantai coast were discussed. For sites with low DIN concentration, many species of three phyla could be used for DIN sources tracing with Laurencia okamurai, Gloiopeltis furcata and Ulva pertusa being ideal species. For site with high DIN concentration, however, species of Rhodophyta were not suitable and only Scytosiphon lomentaria and Monostroma nitidium were chosen. - Highlights: • Yantai coast was affected by three types of DIN sources. • Macroalgal species suitable or not for DIN source tracing were suggested; • TN and δ{sup 15}N were affected by nutrient concentrations and the metabolic factors. • P instead of N limited the tissue N uptake in low nutrient concentration sites.

  19. Selection of effective macroalgal species and tracing nitrogen sources on the different part of Yantai coast, China indicated by macroalgal δ15N values

    International Nuclear Information System (INIS)

    Wang, Yujue; Liu, Dongyan; Richard, Pierre; Di, Baoping

    2016-01-01

    To determine the dominant nitrogen sources and select effective macroalgal species for monitoring eutrophication along the Yantai coast, the total carbon (TOC), total nitrogen (TN) and nitrogen stable isotope ratio (δ 15 N) in macroalgal tissue were analyzed in conjunction with environmental variables in seawater along the Yantai coastline. The ranges of macroalgal tissue δ 15 N values together with dissolved inorganic nitrogen (DIN) composition indicated that except for the atmospheric deposition, there were three dominant types of nitrogen sources along the Yantai coast, with the agricultural fertilizer usage and factorial wastewater input at the S1 (Zhifu Island coast), the sewage discharge at S2 (the Moon Bay coast), the sewage discharge together with aquaculture impacts at S3 (Fisherman Wharf coast) and S4 (the Horse Island coast). Macroalgal growth were not limited by DIN but limited by P at S2, S3 and S4. Macroalgal species suitable or not for DIN source tracing along the Yantai coast were discussed. For sites with low DIN concentration, many species of three phyla could be used for DIN sources tracing with Laurencia okamurai, Gloiopeltis furcata and Ulva pertusa being ideal species. For site with high DIN concentration, however, species of Rhodophyta were not suitable and only Scytosiphon lomentaria and Monostroma nitidium were chosen. - Highlights: • Yantai coast was affected by three types of DIN sources. • Macroalgal species suitable or not for DIN source tracing were suggested; • TN and δ 15 N were affected by nutrient concentrations and the metabolic factors. • P instead of N limited the tissue N uptake in low nutrient concentration sites.

  20. Radioactive aerosols of the object 'Ukryttya' (a review). Part 4.2. Sources and generation of radioactive aerosols during technogenic activities in 1987 - 2005

    International Nuclear Information System (INIS)

    Ogorodnikov, B.I.; Pazukhin, Eh.M.

    2006-01-01

    The sources of radioactive aerosol formation were considered at operation. It is shown that concentrations, radionuclide composition, size distribution, transfer and transformation in environment depended on physical and chemical processes proceeding within reactor breakdown, man-caused activity into premises of the object 'Shelter' and near ChNPP. 34 refs.; 7 figs.; 11 tab

  1. A study of electron density profiles in relation to ionization sources and ground-based radio wave absorption measurements, part 1

    Science.gov (United States)

    Gnanalingam, S.; Kane, J. A.

    1973-01-01

    An extensive set of ground-based measurements of the diurnal variation of medium frequency radio wave adsorption and virtual height is analyzed in terms of current understanding of the D- and lower E-region ion production and loss process. When this is done a gross discrepancy arises, the source of which is not known.

  2. Reduction corporoplasty.

    Science.gov (United States)

    Hakky, Tariq S; Martinez, Daniel; Yang, Christopher; Carrion, Rafael E

    2015-01-01

    Here we present the first video demonstration of reduction corporoplasty in the management of phallic disfigurement in a 17 year old man with a history sickle cell disease and priapism. Surgical management of aneurysmal dilation of the corpora has yet to be defined in the literature. We preformed bilateral elliptical incisions over the lateral corpora as management of aneurysmal dilation of the corpora to correct phallic disfigurement. The patient tolerated the procedure well and has resolution of his corporal disfigurement. Reduction corporoplasty using bilateral lateral elliptical incisions in the management of aneurysmal dilation of the corpora is a safe an feasible operation in the management of phallic disfigurement.

  3. Marine Debris and Plastic Source Reduction Toolkit

    Science.gov (United States)

    Many plastic food service ware items originate on college and university campuses—in cafeterias, snack rooms, cafés, and eateries with take-out dining options. This Campus Toolkit is a detailed “how to” guide for reducing plastic waste on college campuses.

  4. Numerical simulations for the sources apportionment and control strategies of PM2.5 over Pearl River Delta, China, part I: Inventory and PM2.5 sources apportionment.

    Science.gov (United States)

    Huang, Yeqi; Deng, Tao; Li, Zhenning; Wang, Nan; Yin, Chanqin; Wang, Shiqiang; Fan, Shaojia

    2018-09-01

    This article uses the WRF-CMAQ model to systematically study the source apportionment of PM 2.5 under typical meteorological conditions in the dry season (November 2010) in the Pearl River Delta (PRD). According to the geographical location and the relative magnitude of pollutant emission, Guangdong Province is divided into eight subdomains for source apportionment study. The Brute-Force Method (BFM) method was implemented to simulate the contribution from different regions to the PM 2.5 pollution in the PRD. Results show that the industrial sources accounted for the largest proportion. For emission species, the total amount of NO x and VOC in Guangdong Province, and NH 3 and VOC in Hunan Province are relatively larger. In Guangdong Province, the emission of SO 2 , NO x and VOC in the PRD are relatively larger, and the NH 3 emissions are higher outside the PRD. In northerly-controlled episodes, model simulations demonstrate that local emissions are important for PM 2.5 pollution in Guangzhou and Foshan. Meanwhile, emissions from Dongguan and Huizhou (DH), and out of Guangdong Province (SW) are important contributors for PM 2.5 pollution in Guangzhou. For PM 2.5 pollution in Foshan, emissions in Guangzhou and DH are the major contributors. In addition, high contribution ratio from DH only occurs in severe pollution periods. In southerly-controlled episode, contribution from the southern PRD increases. Local emissions and emissions from Shenzhen, DH, Zhuhai-Jiangmen-Zhongshan (ZJZ) are the major contributors. Regional contribution to the chemical compositions of PM 2.5 indicates that the sources of chemical components are similar to those of PM 2.5 . In particular, SO 4 2- is mainly sourced from emissions out of Guangdong Province, while the NO 3- and NH 4+ are more linked to agricultural emissions. Copyright © 2018 Elsevier B.V. All rights reserved.

  5. AGENDA 21 - the basic conceptual document - Agenda of the 21 century which was accepted on the United Nations Conference on Environment and Development (UNCED) in Rio de Janeiro in 1992. Part IV. Sources for realization

    International Nuclear Information System (INIS)

    1996-01-01

    This part of the AGENDA 21 contains 8 chapters: Financial sources and mechanisms; A transfer of environmentally suitable technologies, co-operation and creation of the potential; Science for the sustainable development; Support of the learning, enlightenment and professional organization; National mechanisms and international co-operation at the formation of potential of the development countries; International institutional arrangement; International legal instruments and mechanisms; Information for adjudication. Resolution No 1: The acceptance of the text about the environment and development

  6. The Fate of Iliopsoas Muscle in the Long-term Follow-up After Open Reduction of Developmental Dysplasia of the Hip by Medial Approach. Part 1: MRI Evaluation.

    Science.gov (United States)

    Yilmaz, Serdar; Aksahin, Ertugrul; Duran, Semra; Bicimoglu, Ali

    2017-09-01

    There has been little information about the long-term status of the iliopsoas, which is the main flexor of the hip, after iliopsoas tenotomy in the treatment of developmental dysplasia of the hip (DDH). The aim of this study was to assess the status of the iliopsoas muscle and other flexors and extensors of the hip in long-term follow-up with magnetic resonance imaging after complete iliopsoas tenotomy in patients with unilateral DDH treated with open reduction with a medial approach. The study included 20 patients who underwent open reduction with a medial approach for unilateral DDH and had long-term follow-up. Magnetic resonance imaging assessment of iliopsoas, rectus femoris, tensor fasia lata, sartorius, and gluteus maximus muscles was applied and the muscles of the hip that was operated on were compared with the unoperated hip. In addition, the iliopsoas muscle was examined for reattachment and the effect of reattachment was evaluated. The mean age at the time of operation was 10.53±3.61 months (range, 5 to 18 mo), and mean follow-up was 16.65±2.16 years (range, 13 to 20 y). Spontaneous reattachment of the iliopsoas was observed in 18 patients (90%), either in the lesser trochanter (65%) or the superior part of it (25%). There was no significant difference between the hips that were operated on and those that were not with regard to the mean cross-sectional areas (CSA) of the tensor fascia lata, rectus femoris, sartorius, and gluteus maximus muscles. The CSA of the tensor fascia lata, rectus femoris, sartorius, and gluteus maximus muscles showed no significant difference (P>0.05); however, CSA of iliopsoas muscle was significantly reduced in the operated hip (P<0.001). Although the iliopsoas tendon was atrophied after complete iliopsoas tenotomy, it was reattached in 90% of the patients spontaneously in long-term follow-up. There was no statistically significant compensatory hypertrophy in any muscles in response to iliopsoas atrophy. Level IV-Therapeutic.

  7. The environmental impacts of production and use of energy. Part IV - The comparative assessment of the environmental impacts of energy sources. Phase I - Comparative data on the emissions, residuals and health hazards of energy sources. Report of the Executive Director

    Energy Technology Data Exchange (ETDEWEB)

    Tolba, Mostafa K [United Nations Environment Programme, Nairobi (Kenya)

    1985-01-01

    UNEP has undertaken a number of in-depth reviews of the environmental aspects of production and use of all sources of energy. Three major studies have so far been carried out. The first one, dealing with the environmental impacts of production, transport, processing and use of fossil fuels, was reviewed by an International Panel of Experts that met in Warsaw in April 1978. The second study, which deals with the environmental impacts of nuclear energy, was reviewed by an International Panel of Experts that met in Geneva in November 1978, and was revised at a second meeting held in Nairobi in April 1979. The third study, dealing with the environmental aspects of renewable sources of energy, was reviewed by an International Panel of Experts that met in Bangkok in January 1980. Preparations are already underway to update these three reports. This report was prepared by Dr. Yehia ElMahgary of the UNEP secretariat on the basis of papers prepared for, and discussed in, the course of UNEP's International Panel of Experts on the Comparative Assessment of the Environmental Impacts of Commercial Sources of Energy prepared for by Dr. Essam El-Hinnawi and held in Munich in November 1980, and information provided by participants after the meeting and collected by UNEP from other sources. In the course of the meeting it was realized that our knowledge was not sufficient on several issues, that many approaches existed for tackling the problem, and that it was difficult to agree on unique procedures to undertake the comparison. The draft version of this report was revised again at a second meeting held in December 1983 in New York and additional comments were collected. The Biomedical Laboratory Group of Brookhaven National Laboratory has assisted the UNEP secretariat to collect and update many figures in this cost-benefit analysis of the different sources from the bulk of the report and to treat it in a separate and more comprehensive study. The study is being undertaken by the

  8. The environmental impacts of production and use of energy. Part IV - The comparative assessment of the environmental impacts of energy sources. Phase I - Comparative data on the emissions, residuals and health hazards of energy sources. Report of the Executive Director

    International Nuclear Information System (INIS)

    Tolba, Mostafa K.

    1985-01-01

    UNEP has undertaken a number of in-depth reviews of the environmental aspects of production and use of all sources of energy. Three major studies have so far been carried out. The first one, dealing with the environmental impacts of production, transport, processing and use of fossil fuels, was reviewed by an International Panel of Experts that met in Warsaw in April 1978. The second study, which deals with the environmental impacts of nuclear energy, was reviewed by an International Panel of Experts that met in Geneva in November 1978, and was revised at a second meeting held in Nairobi in April 1979. The third study, dealing with the environmental aspects of renewable sources of energy, was reviewed by an International Panel of Experts that met in Bangkok in January 1980. Preparations are already underway to update these three reports. This report was prepared by Dr. Yehia ElMahgary of the UNEP secretariat on the basis of papers prepared for, and discussed in, the course of UNEP's International Panel of Experts on the Comparative Assessment of the Environmental Impacts of Commercial Sources of Energy prepared for by Dr. Essam El-Hinnawi and held in Munich in November 1980, and information provided by participants after the meeting and collected by UNEP from other sources. In the course of the meeting it was realized that our knowledge was not sufficient on several issues, that many approaches existed for tackling the problem, and that it was difficult to agree on unique procedures to undertake the comparison. The draft version of this report was revised again at a second meeting held in December 1983 in New York and additional comments were collected. The Biomedical Laboratory Group of Brookhaven National Laboratory has assisted the UNEP secretariat to collect and update many figures in this cost-benefit analysis of the different sources from the bulk of the report and to treat it in a separate and more comprehensive study. The study is being undertaken by the

  9. Low-level radioactive waste from commercial nuclear reactors. Volume 3. Bibliographic abstracts of significant source references. Part 2. Bibliography for treatment, storage, disposal and transportation regulatory constraints

    Energy Technology Data Exchange (ETDEWEB)

    Jolley, R.L.; Rodgers, B.R.

    1986-05-01

    The overall task of this program was to provide an assessment of currently available technology for treating commercial low-level radioactive waste (LLRW), to initiate development of a methodology for choosing one technology for a given application, and to identify research needed to improve current treatment techniques and decision methodology. The resulting report is issued in four volumes. Volume 3 of this series is a collection of abstracts of most of the reference documents used for this study. Because of the large volume of literature, the abstracts have been printed in two separate parts. Federal, state, and local regulations affect the decision process for selecting technology applications. Regulations may favor a particular technology and may prevent application of others. Volume 3, part 2 presents abstracts of the regulatory constraint documents that relate to all phases of LLRW management (e.g., treatment, packaging, storage, transportation, and disposal).

  10. Evaluation of Military Field-Water Quality. Volume 2. Constituents of Military Concern from Natural and Anthropogenic Sources. Part 3. Inorganic Chemicals and Physical Properties

    Science.gov (United States)

    1988-01-01

    are available, One of these was prepared by Greathouse and Craun 10 as part of a study concemning the relationship between cardiovascular disease and...a protective effect against diseases of the elderly such as osteoporosis and periodontal disease . A recommended adequate and safe intake level of 1.5... gastrointestinal tract and thus exhibit a low order of toxicity following ingestion by humans. In fact, the relationship between selenium ingestion and any

  11. Value of 100 kVp scan with sinogram-affirmed iterative reconstruction algorithm on a single-source CT system during whole-body CT for radiation and contrast medium dose reduction: an intra-individual feasibility study.

    Science.gov (United States)

    Nagayama, Y; Nakaura, T; Oda, S; Tsuji, A; Urata, J; Furusawa, M; Tanoue, S; Utsunomiya, D; Yamashita, Y

    2018-02-01

    To perform an intra-individual investigation of the usefulness of a contrast medium (CM) and radiation dose-reduction protocol using single-source computed tomography (CT) combined with 100 kVp and sinogram-affirmed iterative reconstruction (SAFIRE) for whole-body CT (WBCT; chest-abdomen-pelvis CT) in oncology patients. Forty-three oncology patients who had undergone WBCT under both 120 and 100 kVp protocols at different time points (mean interscan intervals: 98 days) were included retrospectively. The CM doses for the 120 and 100 kVp protocols were 600 and 480 mg iodine/kg, respectively; 120 kVp images were reconstructed with filtered back-projection (FBP), whereas 100 kVp images were reconstructed with FBP (100 kVp-F) and the SAFIRE (100 kVp-S). The size-specific dose estimate (SSDE), iodine load and image quality of each protocol were compared. The SSDE and iodine load of 100 kVp protocol were 34% and 21%, respectively, lower than of 120 kVp protocol (SSDE: 10.6±1.1 versus 16.1±1.8 mGy; iodine load: 24.8±4versus 31.5±5.5 g iodine, p<0.01). Contrast enhancement, objective image noise, contrast-to-noise-ratio, and visual score of 100 kVp-S were similar to or better than of 120 kVp protocol. Compared with the 120 kVp protocol, the combined use of 100 kVp and SAFIRE in WBCT for oncology assessment with an SSCT facilitated substantial reduction in the CM and radiation dose while maintaining image quality. Copyright © 2017 The Royal College of Radiologists. Published by Elsevier Ltd. All rights reserved.

  12. Reduction Corporoplasty

    Directory of Open Access Journals (Sweden)

    Tariq S. Hakky

    2015-04-01

    Full Text Available Objective Here we present the first video demonstration of reduction corporoplasty in the management of phallic disfigurement in a 17 year old man with a history sickle cell disease and priapism. Introduction Surgical management of aneurysmal dilation of the corpora has yet to be defined in the literature. Materials and Methods: We preformed bilateral elliptical incisions over the lateral corpora as management of aneurysmal dilation of the corpora to correct phallic disfigurement. Results The patient tolerated the procedure well and has resolution of his corporal disfigurement. Conclusions Reduction corporoplasty using bilateral lateral elliptical incisions in the management of aneurysmal dilation of the corpora is a safe an feasible operation in the management of phallic disfigurement.

  13. A Systematic Review of Surgical Randomized Controlled Trials: Part 2. Funding Source, Conflict of Interest, and Sample Size in Plastic Surgery.

    Science.gov (United States)

    Voineskos, Sophocles H; Coroneos, Christopher J; Ziolkowski, Natalia I; Kaur, Manraj N; Banfield, Laura; Meade, Maureen O; Chung, Kevin C; Thoma, Achilleas; Bhandari, Mohit

    2016-02-01

    The authors examined industry support, conflict of interest, and sample size in plastic surgery randomized controlled trials that compared surgical interventions. They hypothesized that industry-funded trials demonstrate statistically significant outcomes more often, and randomized controlled trials with small sample sizes report statistically significant results more frequently. An electronic search identified randomized controlled trials published between 2000 and 2013. Independent reviewers assessed manuscripts and performed data extraction. Funding source, conflict of interest, primary outcome direction, and sample size were examined. Chi-squared and independent-samples t tests were used in the analysis. The search identified 173 randomized controlled trials, of which 100 (58 percent) did not acknowledge funding status. A relationship between funding source and trial outcome direction was not observed. Both funding status and conflict of interest reporting improved over time. Only 24 percent (six of 25) of industry-funded randomized controlled trials reported authors to have independent control of data and manuscript contents. The mean number of patients randomized was 73 per trial (median, 43, minimum, 3, maximum, 936). Small trials were not found to be positive more often than large trials (p = 0.87). Randomized controlled trials with small sample size were common; however, this provides great opportunity for the field to engage in further collaboration and produce larger, more definitive trials. Reporting of trial funding and conflict of interest is historically poor, but it greatly improved over the study period. Underreporting at author and journal levels remains a limitation when assessing the relationship between funding source and trial outcomes. Improved reporting and manuscript control should be goals that both authors and journals can actively achieve.

  14. Manufacturing cost study on the ion sources for the Mirror Fusion Test Facility

    International Nuclear Information System (INIS)

    A study of the cost of manufacturing 48 ion sources for the Mirror Fusion Test Facility is described. The estimate is built up from individual part costs and assembly operation times for the 80 kV prototype source constructed by LLL and described by LLL drawings furnished during December 1978. Recommendations for cost reduction are made

  15. Campus and community micro grids integration of building integrated photovoltaic renewable energy sources: Case study of Split 3 area, Croatia - part A

    Directory of Open Access Journals (Sweden)

    Gašparović Goran

    2016-01-01

    Full Text Available Micro grids interconnect loads and distributed energy resources as a single controllable entity. New installations of renewable energy sources (RES in urban areas, such as Building Integrated Photovoltaic (BIPV, provide opportunities to increase energy independence and diversify energy sources in the energy system. This paper explores the integration of RES into two case study communities in an urban agglomeration to provide optimal conditions to meet a share of the electrical loads. Energy planning case studies for decentralized generation of renewable energy are conducted in H2RES energy planning software for hourly energy balances. The results indicate that BIPV and PV in the case study communities can cover about 17% of the recorded electrical demand of both areas. On a yearly basis, there will be a 0.025 GWh surplus of PV production with a maximum value of 1.25 MWh in one hour of operation unless grid storage is used. This amounts to a total investment cost of 13.36 million EUR. The results are useful for proposing future directions for the various case study communities targeting sustainable development.

  16. Seismologic study of Los Hum eros geothermal field, Pueblo, Mexico. Part I: Seismicity, source mechanisms and stress distribution; Estudio sismologico del campo geotermico de Los Humeros, Puebla, Mexico. Parte I: Sismicidad, mecanismos de fuente y distribucion de esfuerzos

    Energy Technology Data Exchange (ETDEWEB)

    Lermo, Javier; Antayhua, Yanet [Instituto de Ingenieria, Universidad Nacional Autonoma de Mexico, Mexico D.F (Mexico)]. E-Mail: jles@pumas.iingen.unam.mx; Quintanar, Luis [Instituto de Geofisica, Universidad Nacional Autonoma de Mexico, Mexico D.F (Mexico); Lorenzo, Cecilia [Gerencia de Proyectos Geotermoelectricos, Comision Federal de Electricidad, Michoacan (Mexico)

    2008-01-15

    The distribution of earthquakes at the surface and at depth in the Los Humeros geothermal field, Puebla (Mexico), is analyzed from 1997-2004. Data for 95 earthquakes were registered at more than five permanent and temporary stations installed by the Comision Federal de Electricidad and the Instituto de Ingenieria of the Universidad Nacional Autonoma de Mexico. The duration magnitudes of the quakes are equal to or lower than 3.6 Md and the focal depths do not exceed 4.0 km. Simple focal mechanisms and moment tensor inversions were made, and the number of earthquakes registered by two stations of the permanent network (numbers S05, S06) was compared with water-injection and steam-production volumes over a certain period. The results at the surface and at depth show seismic activity occurring in the northern zone of the field around injection wells I29 (well H-29) and I38 (well H-38); whereas, the simple focal mechanisms and moment tensors demonstrate stresses of heterogeneous origin, suggesting that part of the seismic activity in Los Humeros is probably induced, mainly by injecting water. [Spanish] Se analiza la distribucion en superficie y en profundidad de los sismos ocurridos en el campo geotermico de Los Humeros, Puebla (Mexico), durante el periodo 1997-2004. Los datos corresponden a 95 sismos registrados por mas de cinco estaciones permanentes y temporales instaladas por la Comision Federal de Electricidad y el Instituto de Ingenieria de la Universidad Nacional Autonoma de Mexico, cuyas magnitudes de duracion son menores o iguales a 3.6 Md y profundidades focales que no sobrepasan los 4.0 km. Asimismo, se realizaron mecanismos focales simples y de inversion de tensor de momento, y se comparo el numero de sismos registrados por dos estaciones de la red permanente (numeros S05, S06) con la inyeccion de agua y la produccion de vapor durante cierto tiempo. Los resultados en superficie y en profundidad muestran actividad sismica en la zona norte del campo, alrededor

  17. Effect of chemically processed bonemeal in comparison to other phosphatic sources on plant growth - [Part]1 : rice wheat rotation in an alluvial soil

    International Nuclear Information System (INIS)

    Vimal, O.P.; Ramasami, S.

    1976-01-01

    The effect of chemically processed bonemeal was studied in comparison to other phosphatic sources viz., superphosphate, steamed bonemeal and raw bonemeal at the rate of 60 and 120 kg P 2 O 5 /ha on rice in alluvial soil. The residual effect was studied with wheat using 32 P as a tracer. The results showed that in the first crop (rice), superphosphate at the rate of 120 kg/ha had a significant effect both on dry matter yield and nutrient uptake. In the second crop (wheat), chemically processed bonemeal at the rate of 120 kg/ha showed a marked positive effect on yield, total P uptake and 'A' values. The effects of steamed bonemeal and raw bonemeal were significantly lower compared to above effects. (author)

  18. Investigating organic matter in Fanno Creek, Oregon, Part 2 of 3: sources, sinks, and transport of organic matter with fine sediment

    Science.gov (United States)

    Keith, Mackenzie K.; Sobieszczyk, Steven; Goldman, Jami H.; Rounds, Stewart A.

    2014-01-01

    Organic matter (OM) is abundant in Fanno Creek, Oregon, USA, and has been tied to a variety of water-quality concerns, including periods of low dissolved oxygen downstream in the Tualatin River, Oregon. The key sources of OM in Fanno Creek and other Tualatin River tributaries have not been fully identified, although isotopic analyses from previous studies indicated a predominantly terrestrial source. This study investigates the role of fine sediment erosion and deposition (mechanisms and spatial patterns) in relation to OM transport. Geomorphic mapping within the Fanno Creek floodplain shows that a large portion (approximately 70%) of the banks are eroding or subject to erosion, likely as a result of the imbalance caused by anthropogenic alteration. Field measurements of long- and short-term bank erosion average 4.2 cm/year and average measurements of deposition for the watershed are 4.8 cm/year. The balance between average annual erosion and deposition indicates an export of 3,250 metric tons (tonnes, t) of fine sediment to the Tualatin River—about twice the average annual export of 1,880 t of sediment at a location 2.4 km from the creek’s mouth calculated from suspended sediment load regressions from continuous turbidity data and suspended sediment samples. Carbon content from field samples of bank material, combined with fine sediment export rates, indicates that about 29–67 t of carbon, or about 49–116 t of OM, from bank sediment may be exported to the Tualatin River from Fanno Creek annually, an estimate that is a lower bound because it does not account for the mass wasting of organic-rich O and A soil horizons that enter the stream.

  19. Snubber reduction

    International Nuclear Information System (INIS)

    Olson, D.E.; Singh, A.K.

    1986-01-01

    Many safety-related piping systems in nuclear power plants have been oversupported. Since snubbers make up a large percentage of the pipe supports or restraints used in a plant, a plant's snubber population is much larger than required to adequately restrain the piping. This has resulted in operating problems and unnecessary expenses for maintenance and inservice inspections (ISIs) of snubbers. This paper presents an overview of snubber reduction, including: the incentives for removing snubbers, a historical perspective on how piping became oversupported, why it is possible to remove snubbers, and the costs and benefits of doing so

  20. Distribution, sources and contamination assessment of heavy metals in surface sediments of the South Yellow Sea and northern part of the East China Sea.

    Science.gov (United States)

    Lu, Jian; Li, Anchun; Huang, Peng

    2017-11-15

    Surface sediment samples collected from the South Yellow Sea and northern part of the East China Sea during spring and autumn, respectively, were analyzed for grain size, aluminum, and heavy metals (Cr, Ni, Cu, Zn, and Pb) to evaluate heavy metal levels and the contamination status. The results showed that all of the heavy metal concentrations met the standard criteria of the Chinese National Standard Criteria for Marine Sediment Quality. Both the EFs and a multivariate analysis (PCA) indicated that Cr, Ni, Cu, and Zn were mainly from natural contributions, while Pb was influenced by anthropogenic inputs, especially during autumn. The geoaccumulation index of Pb near the mouth of the Yangtze River suggested that the pollution degree in autumn was heavier than that in spring, which might be caused by the greater river discharge in summer and more heavy metal adsorption with finer grain sizes. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Efficacy studies of Reactive Skin Decontamination Lotion, M291 Skin Decontamination Kit, 0.5% bleach, 1% soapy water, and Skin Exposure Reduction Paste Against Chemical Warfare Agents, part 1: guinea pigs challenged with VX.

    Science.gov (United States)

    Braue, Ernest H; Smith, Kelly H; Doxzon, Bryce F; Lumpkin, Horace L; Clarkson, Edward D

    2011-03-01

    This report, first in a series of five, directly compares the efficacy of 4 decontamination products and Skin Exposure Reduction Paste Against Chemical Warfare Agents (SERPACWA) in the haired guinea pig model following exposure to VX. In all experiments, guinea pigs were close-clipped and given anesthesia. In the decontamination experiments, the animals were challenged with VX and decontaminated after a 2-minute delay for the standard procedure or at longer times for the delayed-decontamination experiments. Skin Exposure Reduction Paste Against Chemical Warfare Agents was applied as a thin coating (0.1 mm thick), allowed to dry for 15 minutes, and challenged with VX. After a 2-hour challenge, any remaining VX was blotted off the animal, but no additional decontamination was done. Positive control animals were challenged with VX in the same manner as the treated animals, except that they received no treatment. In addition, the positive control animals were always challenged with 5% VX in isopropyl alcohol (IPA) solution, whereas the treatment animals received either neat (undiluted) VX or 5% VX in IPA solution. All animals were observed during the first 4 hours and again at 24 hours after exposure for signs of toxicity and death. The protective ratio (PR, defined as the median lethal dose [LD(50)] of the treatment group divided by the LD(50) of the untreated positive control animals) was calculated from the probit dose-response curves established for each treatment group and nontreated control animals. Significance in this report was defined as p decontamination experiments, the calculated PRs for Reactive Skin Decontamination Lotion (RSDL), 0.5% bleach, 1% soapy water, and the M291 Skin Decontamination Kit (SDK) were 66, 17, 16, and 1.1, respectively. Reactive Skin Decontamination Lotion was by far the most effective decontamination product tested and was significantly better than any of the other products. Bleach and soapy water provided equivalent and good (PR

  2. RATIONAL STRUCTURES OF POLITICS IN MONTESQUIEU’S THE SPIRIT OF THE LAWS. PART I: THE KEY ELEMENTS LEGITIMATING THE POWER AND ITS SOURCES

    Directory of Open Access Journals (Sweden)

    MARIUS DUMITRESCU

    2013-05-01

    Full Text Available In The Spirit of the Laws, Montesquieu tried not to discuss about laws, but in fact, about the type of power hiding behind them. Inspired by Plato and Aristotle, he built his own vision on the palingenesis of the political forms and of the principles governing them. Baron de La Brède started from ideas, from spiritual structures, that have the role to create certain social behaviors, and identified three types of government forms, each characterized by its own nature and principle: monarchy, democracy, and despotism. The French philosopher tried to understand, besides the principles ensuring the nature of each government, the key elements legitimating the power and also its sources. The monarchy is seen by Montesquieu as the most suitable regime, for his time, to rule free societies. The aristocracy helps to the maintenance of freedom in royalty by resisting to any attempt of the crown to exceed its constitutional prerogatives. The transition from one form of government to another is done because of the alteration of principles. Democracy is maybe the most exposed to alteration as its excess of freedom leads to the affirmation of the spirit of endless equality that makes everybody wanting to be the equals to the rulers. Montesquieu sees no other solution to replace the degraded forms of political organization than the confederative republic. Such a political organization would answer the need for permanent political flexibility.

  3. Seasonal dynamics of freshwater pathogens as measured by microarray at Lake Sapanca, a drinking water source in the north-eastern part of Turkey.

    Science.gov (United States)

    Akçaalan, Reyhan; Albay, Meric; Koker, Latife; Baudart, Julia; Guillebault, Delphine; Fischer, Sabine; Weigel, Wilfried; Medlin, Linda K

    2017-12-22

    Monitoring drinking water quality is an important public health issue. Two objectives from the 4 years, six nations, EU Project μAqua were to develop hierarchically specific probes to detect and quantify pathogens in drinking water using a PCR-free microarray platform and to design a standardised water sampling program from different sources in Europe to obtain sufficient material for downstream analysis. Our phylochip contains barcodes (probes) that specifically identify freshwater pathogens that are human health risks in a taxonomic hierarchical fashion such that if species is present, the entire taxonomic hierarchy (genus, family, order, phylum, kingdom) leading to it must also be present, which avoids false positives. Molecular tools are more rapid, accurate and reliable than traditional methods, which means faster mitigation strategies with less harm to humans and the community. We present microarray results for the presence of freshwater pathogens from a Turkish lake used drinking water and inferred cyanobacterial cell equivalents from samples concentrated from 40 into 1 L in 45 min using hollow fibre filters. In two companion studies from the same samples, cyanobacterial toxins were analysed using chemical methods and those dates with highest toxin values also had highest cell equivalents as inferred from this microarray study.

  4. Essential Oils from Different Plant Parts of Eucalyptus cinerea F. Muell. ex Benth. (Myrtaceae as a Source of 1,8-Cineole and Their Bioactivities

    Directory of Open Access Journals (Sweden)

    Tomoe Nakashima

    2011-11-01

    Full Text Available Eucalyptus cinerea, known as silver dollar tree, has few descriptions in traditional medicine. Chemical composition and antimicrobial properties of the essential oils of leaves, flowers and fruits, collected seasonally, were determined by GC/MS and disk diffusion/MIC, respectively. 1,8-Cineole was the main compound, particularly in fresh leaves—Spring (74.98%, dried leaves—Spring (85.32%, flowers—Winter (78.76% and fruits—Winter (80.97%. Other compounds were found in the aerial parts in all seasons: α-pinene (2.41% to 10.13%, limonene (1.46% to 4.43%, α-terpineol (1.73% to 11.72%, and α-terpinyl acetate (3.04% to 20.44%. The essential oils showed antimicrobial activities against bacteria and yeasts, with the best results being found for the dried autumn and winter leaves oils (MIC < 0.39 mg/mL against Streptococcus pyogenes. For the other tested microorganisms the following MIC results were found: Staphylococcus aureus—Dried leaves oil from summer (0.78 mg/mL, Pseudomonas aeruginosa—Flowers oil from autumn and fruits oil from winter (1.56 mg/mL and Candida albicans—Flowers oil from autumn and fruits oils from winter and spring (0.78 mg/mL.

  5. Radon reduction

    International Nuclear Information System (INIS)

    Hamilton, M.A.

    1990-01-01

    During a radon gas screening program, elevated levels of radon gas were detected in homes on Mackinac Island, Mich. Six homes on foundations with crawl spaces were selected for a research project aimed at reducing radon gas concentrations, which ranged from 12.9 to 82.3 pCi/l. Using isolation and ventilation techniques, and variations thereof, radon concentrations were reduced to less than 1 pCi/l. This paper reports that these reductions were achieved using 3.5 mil cross laminated or 10 mil high density polyethylene plastic as a barrier without sealing to the foundation or support piers, solid and/or perforated plastic pipe and mechanical fans. Wind turbines were found to be ineffective at reducing concentrations to acceptable levels. Homeowners themselves installed all materials

  6. [Study of self-reported health of people living near point sources of environmental pollution: a review. First part: health indicators].

    Science.gov (United States)

    Daniau, C; Dor, F; Eilstein, D; Lefranc, A; Empereur-Bissonnet, P; Dab, W

    2013-08-01

    Epidemiological studies have investigated the health impacts of local sources of environmental pollution using as an outcome variable self-reported health, reflecting the overall perception interviewed people have of their own health. This work aims at analyzing the advantages and the results of this approach. A first step focused on describing the indicators. The literature on indicators of self-reported health was reviewed, leading to a discussion on data collection, selection of health effects, data processing, and construction of indicators. The literature review concerned 51 articles. The use of self-reported health indicators allowed the studies to take into account the health concerns and complaints of populations exposed to environmental pollution. Various indicators of self-reported health were used in the studies. They measured physical, psychological and general dimensions of health. Standardized questionnaires were used less often than ad hoc questionnaires (78% of studies) developed to fit the needs of a given study. Three standardized questionnaires were used more frequently: the MOS Short-Form Health Survey (SF-36) to measure general health perceptions, the General Health Questionnaire (GHQ), and the Symptoms Checklist (SCL-90) to measure psychological distress. The choice of self-reported health indicators is a compromise between specificity of the studied health issues within a given environment and standardization of the questionnaires used to measure them. Such standardization is necessary to ensure the validity and the reliability of the information collected across time and situations. The psychometric properties of the measuring questionnaires are rarely estimated or verified when they are used. Copyright © 2013 Elsevier Masson SAS. All rights reserved.

  7. [Evaluation of visualization of biological stains with the use of alternative light source (ALS) for the purpose of genetic identification. Part I. Blood and saliva stains analysis].

    Science.gov (United States)

    Szeremeta, Michał; Pepiński, Witold; Niemcunowicz-Janica, Anna; Skawrońska, Małgorzata; Sackiewicz, Adam; Ptaszyńska-Sarosiek, Iwona; Okłota, Magdalena

    2010-01-01

    The objective of the investigation was evaluation of visualization of human blood and saliva stains with the use of alternative light source for the purpose of genetic identification. Experimental bloodstains on the bright base were the most clearly seen in the natural light and white light, up to blood dilution of 1:600. Complete typeability of AmpFISTR SGM Plus kit profiles was obtained from bloodstains at dilution 1:1500. Partial AmpFISTR SGM Plus kit profiles were typed from bloodstains at dilutions 1:1750 and 1:2000. Experimental saliva stains on the light-colored base were completely invisible in the natural light and white light, while they were visualized at wavelength range 300-415 nm through yellow goggles, and at wavelength range 300-455 nm through orange goggles at saliva dilution 1: 600. Complete typeability of AmpFISTR SGM Plus kit loci was obtained from saliva stains at dilution 1:1750. Partial AmpFISTR SGM Plus kit profiles were typed from saliva stains at dilution 1:2000. The wavelength of 455 nm and orange goggles were the optimal set for visualization of bloodstains on various, noncontrasting materials. Other useful wavelength/combinations of goggles were CSS light/red goggles. In case of saliva, the most useful general condition for visualization of stains on various, non-contrasting materials was with the wavelength set to 300-415 nm, while wearing yellow goggles. Other useful combinations of wavelength/goggles were 300-455 nm/orange or red goggles, and also CSS light/orange or red goggles.

  8. [What do we know about psychosocial risks at work? Part II.The analysis of employee's knowledge of sources and consequences of stress at work].

    Science.gov (United States)

    Potocka, Adrianna; Merecz-Kot, Dorota

    2010-01-01

    Psychosocial risks at work are the challenge facing the occupational health and safety protection. They are seen as a threat to the employees' health and functioning. They also contribute to negative outcomes in the organizations. The study was focused on the assessment of employees' knowledge of occupational stressors, their consequences and preventive measures. The assessment results will help in the development of an educational program aimed at increasing awareness of occupational stress among employees. 210 employees participated in the study. By the mean of survey "Psychosocial Risks at Work-place" the information on the respondents' knowledge of occupational stress issues was collected. Stressors intrinsic to the job (mostly work overload) were recognized as best known to employees (67.62%). The second place was occupied by stressors originating from interpersonal relationships at work (51.9% of respondents pointed out that problem). Almost no one (0.48%) mentioned home-work interference as a source of occupational stress. According to the respondents' opinion, occupational stress mostly results in health decline. The employees who participated in the study believe that the employer (13.81%) or the superior (19.05%) is responsible for psychosocial risks prevention at the work place. Almost a half of subjects (46.67%) did not know whether there are any law regulations on psychosocial risk at work in Poland. The respondents showed an average level of knowledge of psychosocial risk at the work place and knew almost nothing about occupational stress prevention. The results of the study point to the need for systematic education of employees about stress and stress related issues.

  9. Natural mineral bottled waters available on the Polish market as a source of minerals for the consumers. Part 1. Calcium and magnesium.

    Science.gov (United States)

    Gątarska, Anna; Tońska, Elżbieta; Ciborska, Joanna

    2016-01-01

    Natural mineral waters may be an essential source of calcium, magnesium and other minerals. In bottled waters, minerals occur in an ionized form which is very well digestible. However, the concentration of minerals in underground waters (which constitute the material for the production of bottled waters) varies. In view of the above, the type of water consumed is essential. The aim of the study was to estimate the calcium and magnesium contents in products available on the market and to evaluate calcium and magnesium consumption with natural mineral water by different consumer groups with an assumed volume of the consumed product. These represented forty different brands of natural mineral available waters on Polish market. These waters were produced in Poland or other European countries. Among the studied products, about 30% of the waters were imported from Lithuania, Latvia, Czech Republic, France, Italy and Germany. The content of calcium and magnesium in mineral waters was determined using flame atomic absorption spectrometry in an acetylene-air flame. Further determinations were carried out using atomic absorption spectrometer--ICE 3000 SERIES-THERMO-England, equipped with a GLITE data station, background correction (a deuterium lamp) as well as other cathode lamps. Over half of the analysed natural mineral waters were medium-mineralized. The natural mineral waters available on the market can be characterized by a varied content of calcium and magnesium and a high degree of product mineralization does not guarantee significant amounts of these components. Among the natural mineral waters available on the market, only a few feature the optimum calcium-magnesium proportion (2:1). Considering the mineralization degree of the studied products, it can be stated that the largest percentage of products with significant calcium and magnesium contents can be found in the high-mineralized water group. For some natural mineral waters, the consumption of 1 litre daily may

  10. Neutron source

    International Nuclear Information System (INIS)

    Cason, J.L. Jr.; Shaw, C.B.

    1975-01-01

    A neutron source which is particularly useful for neutron radiography consists of a vessel containing a moderating media of relatively low moderating ratio, a flux trap including a moderating media of relatively high moderating ratio at the center of the vessel, a shell of depleted uranium dioxide surrounding the moderating media of relatively high moderating ratio, a plurality of guide tubes each containing a movable source of neutrons surrounding the flux trap, a neutron shield surrounding one part of each guide tube, and at least one collimator extending from the flux trap to the exterior of the neutron source. The shell of depleted uranium dioxide has a window provided with depleted uranium dioxide shutters for each collimator. Reflectors are provided above and below the flux trap and on the guide tubes away from the flux trap

  11. A Baltic Sea estuary as a phosphorus source and sink after drastic load reduction: seasonal and long-term mass balances for the Stockholm inner archipelago for 1968-2015

    Science.gov (United States)

    Walve, Jakob; Sandberg, Maria; Larsson, Ulf; Lännergren, Christer

    2018-05-01

    Internal phosphorus (P) loading from sediments, controlled by hypoxia, is often assumed to hamper the recovery of lakes and coastal areas from eutrophication. In the early 1970s, the external P load to the inner archipelago of Stockholm, Sweden (Baltic Sea), was drastically reduced by improved sewage treatment, but the internal P loading and its controlling factors have been poorly quantified. We use two slightly different four-layer box models to calculate the area's seasonal and annual P balance (input-export) and the internal P exchange with sediments in 1968-2015. For 10-20 years after the main P load reduction, there was a negative P balance, small in comparison to the external load, and probably due to release from legacy sediment P storage. Later, the stabilized, near-neutral P balance indicates no remaining internal loading from legacy P, but P retention is low, despite improved oxygen conditions. Seasonally, sediments are a P sink in spring and a P source in summer and autumn. Most of the deep-water P release from sediments in summer-autumn appears to be derived from the settled spring bloom and is exported to outer areas during winter. Oxygen consumption and P release in the deep water are generally tightly coupled, indicating limited iron control of P release. However, enhanced P release in years of deep-water hypoxia suggests some contribution from redox-sensitive P pools. Increasing deep-water temperatures that stimulate oxygen consumption rates in early summer have counteracted the effect of lowered organic matter sedimentation on oxygen concentrations. Since the P turnover time is short and legacy P small, measures to bind P in Stockholm inner archipelago sediments would primarily accumulate recent P inputs, imported from the Baltic Sea and from Lake Mälaren.

  12. Waste Minimization via Radiological Hazard Reduction

    International Nuclear Information System (INIS)

    Stone, K.A.; Coffield, T.; Hooker, K.L.

    1998-01-01

    The Savannah River Site (SRS), a 803 km 2 U.S. Department of Energy (DOE) facility in south-western South Carolina, incorporates pollution prevention as a fundamental component of its Environmental Management System. A comprehensive pollution prevention program was implemented as part of an overall business strategy to reduce waste generation and pollution releases, minimize environmental impacts, and to reduce future waste management and pollution control costs. In fiscal years 1995 through 1997, the Site focused on implementing specific waste reduction initiatives identified while benchmarking industry best practices. These efforts resulted in greater than $25 million in documented cost avoidance. While these results have been dramatic to date, the Site is further challenged to maximize resource utilization and deploy new technologies and practices to achieve further waste reductions. The Site has elected to target a site-wide reduction of contaminated work spaces in fiscal year 1998 as the primary source reduction initiative. Over 120,900 m 2 of radiologically contaminated work areas (approximately 600 separate inside areas) exist at SRS. Reduction of these areas reduces future waste generation, minimizes worker exposure, and reduces surveillance and maintenance costs. This is a major focus of the Site's As Low As Reasonably Achievable (ALARA) program by reducing sources of worker exposure. The basis for this approach was demonstrated during 1997 as part of a successful Enhanced Work Planning pilot conducted at several specific contamination areas at SRS. An economic-based prioritization process was utilized to develop a model for prioritizing areas to reclaim. In the H-Canyon Separation facility, over 3,900 m 2 of potentially contaminated area was rolled back to a Radiation Buffer Area. The facility estimated nearly 420 m 3 of low level radioactive waste will be avoided each year, and overall cost savings and productivity gains will reach approximately $1

  13. NF ISO 7097-1. Nuclear fuel technology - Uranium dosimetry in solutions, in uranium hexafluoride and in solids - Part 1: reduction with iron (II) / oxidation with potassium bi-chromate / titration method

    International Nuclear Information System (INIS)

    2002-04-01

    This standard document describes the mode of operation of three different methods for the quantitative dosimetry of uranium in solutions, in UF 6 and in solids: reduction by iron (II), oxidation by potassium bi-chromate and titration. (J.S.)

  14. Biochemistry of Catabolic Reductive Dehalogenation.

    Science.gov (United States)

    Fincker, Maeva; Spormann, Alfred M

    2017-06-20

    A wide range of phylogenetically diverse microorganisms couple the reductive dehalogenation of organohalides to energy conservation. Key enzymes of such anaerobic catabolic pathways are corrinoid and Fe-S cluster-containing, membrane-associated reductive dehalogenases. These enzymes catalyze the reductive elimination of a halide and constitute the terminal reductases of a short electron transfer chain. Enzymatic and physiological studies revealed the existence of quinone-dependent and quinone-independent reductive dehalogenases that are distinguishable at the amino acid sequence level, implying different modes of energy conservation in the respective microorganisms. In this review, we summarize current knowledge about catabolic reductive dehalogenases and the electron transfer chain they are part of. We review reaction mechanisms and the role of the corrinoid and Fe-S cluster cofactors and discuss physiological implications.

  15. A Two-Microphone Noise Reduction System for Cochlear Implant Users with Nearby Microphones—Part I: Signal Processing Algorithm Design and Development

    Directory of Open Access Journals (Sweden)

    Marco Pelizzone

    2008-06-01

    Full Text Available Users of cochlear implant systems, that is, of auditory aids which stimulate the auditory nerve at the cochlea electrically, often complain about poor speech understanding in noisy environments. Despite the proven advantages of multimicrophone directional noise reduction systems for conventional hearing aids, only one major manufacturer has so far implemented such a system in a product, presumably because of the added power consumption and size. We present a physically small (intermicrophone distance 7 mm and computationally inexpensive adaptive noise reduction system suitable for behind-the-ear cochlear implant speech processors. Supporting algorithms, which allow the adjustment of the opening angle and the maximum noise suppression, are proposed and evaluated. A portable real-time device for test in real acoustic environments is presented.

  16. Plume-related mantle source of super-large rare metal deposits from the Lovozero and Khibina massifs on the Kola Peninsula, Eastern part of Baltic Shield: Sr, Nd and Hf isotope systematics

    Science.gov (United States)

    Kogarko, L. N.; Lahaye, Y.; Brey, G. P.

    2010-03-01

    The two world’s largest complexes of highly alkaline nepheline syenites and related rare metal loparite and eudialyte deposits, the Khibina and Lovozero massifs, occur in the central part of the Kola Peninsula. We measured for the first time in situ the trace element concentrations and the Sr, Nd and Hf isotope ratios by LA-ICP-MS (laser ablation inductively coupled plasma mass spectrometer) in loparite, eudialyte an in some other pegmatitic minerals. The results are in aggreement with the whole rock Sr and Nd isotope which suggests the formation of these superlarge rare metal deposits in a magmatic closed system. The initial Hf, Sr, Nd isotope ratios are similar to the isotopic signatures of OIB indicating depleted mantle as a source. This leads to the suggestion that the origin of these gigantic alkaline intrusions is connected to a deep seated mantle source—possibly to a lower mantle plume. The required combination of a depleted mantle and high rare metal enrichment in the source can be explained by the input of incompatible elements by metasomatising melts/fluids into the zones of alkaline magma generation shortly before the partial melting event (to avoid ingrowth of radiogenic isotopes). The minerals belovite and pyrochlore from the pegmatites are abnormally high in 87Sr /86Sr ratios. This may be explained by closed system isotope evolution as a result of a significant increase in Rb/Sr during the evolution of the peralkaline magma.

  17. Low-level radioactive waste from commercial nuclear reactors. Volume 3. Bibliographic abstracts of significant source documents. Part 1. Open-literature abstracts for low-level radioactive waste

    Energy Technology Data Exchange (ETDEWEB)

    Bowers, M.K.; Rodgers, B.R.; Jolley, R.L.

    1986-05-01

    The overall task of this program was to provide an assessment of currently available technology for treating commercial low-level radioactive waste (LLRW), to initiate development of a methodology for choosing one technology for a given application, and to identify research needed to improve current treatment techniques and decision methodology. The resulting report is issued in four volumes. Volume 3 of this series is a collection of abstracts of most of the reference documents used for this study. Because of the large volume of literature, the abstracts have been printed in two separate parts. Volume 3, part 1 presents abstracts of the open literature relating to LLRW treatment methodologies. Some of these references pertain to treatment processes for hazardous wastes that may also be applicable to LLRW management. All abstracts have been limited to 21 lines (for brevity), but each abstract contains sufficient information to enable the reader to determine the potential usefulness of the source document and to locate each article. The abstracts are arranged alphabetically by author or organization, and indexed by keyword.

  18. Low-level radioactive waste from commercial nuclear reactors. Volume 3. Bibliographic abstracts of significant source documents. Part 1. Open-literature abstracts for low-level radioactive waste

    International Nuclear Information System (INIS)

    Bowers, M.K.; Rodgers, B.R.; Jolley, R.L.

    1986-05-01

    The overall task of this program was to provide an assessment of currently available technology for treating commercial low-level radioactive waste (LLRW), to initiate development of a methodology for choosing one technology for a given application, and to identify research needed to improve current treatment techniques and decision methodology. The resulting report is issued in four volumes. Volume 3 of this series is a collection of abstracts of most of the reference documents used for this study. Because of the large volume of literature, the abstracts have been printed in two separate parts. Volume 3, part 1 presents abstracts of the open literature relating to LLRW treatment methodologies. Some of these references pertain to treatment processes for hazardous wastes that may also be applicable to LLRW management. All abstracts have been limited to 21 lines (for brevity), but each abstract contains sufficient information to enable the reader to determine the potential usefulness of the source document and to locate each article. The abstracts are arranged alphabetically by author or organization, and indexed by keyword

  19. NF ISO 14064-2. Greenhouse gases. Part 2: specifications and guidance at the project level for quantification, monitoring and reporting of greenhouse gas emission reductions or removal enhancements

    International Nuclear Information System (INIS)

    2005-01-01

    This document describes methodology for quantification, monitoring and reporting of activities intended to cause greenhouse gas emissions and reductions at projects level (activity modifying the conditions identified in a baseline scenario, intended to reduce emissions or to increase the removal of greenhouse gases). Thus it suggests a method for the declarations of inventory of projects greenhouse gases and provides support for the monitoring and the management of emissions. It provides terms and definitions, principles, the introduction to greenhouse gases projects and the requirements for greenhouse gas projects. (A.L.B.)

  20. Speckle reduction methods in laser-based picture projectors

    Science.gov (United States)

    Akram, M. Nadeem; Chen, Xuyuan

    2016-02-01

    Laser sources have been promised for many years to be better light sources as compared to traditional lamps or light-emitting diodes (LEDs) for projectors, which enable projectors having wide colour gamut for vivid image, super brightness and high contrast for the best picture quality, long lifetime for maintain free operation, mercury free, and low power consumption for green environment. A major technology obstacle in using lasers for projection has been the speckle noise caused by to the coherent nature of the lasers. For speckle reduction, current state of the art solutions apply moving parts with large physical space demand. Solutions beyond the state of the art need to be developed such as integrated optical components, hybrid MOEMS devices, and active phase modulators for compact speckle reduction. In this article, major methods reported in the literature for the speckle reduction in laser projectors are presented and explained. With the advancement in semiconductor lasers with largely reduced cost for the red, green and the blue primary colours, and the developed methods for their speckle reduction, it is hoped that the lasers will be widely utilized in different projector applications in the near future.

  1. Source rock

    Directory of Open Access Journals (Sweden)

    Abubakr F. Makky

    2014-03-01

    Full Text Available West Beni Suef Concession is located at the western part of Beni Suef Basin which is a relatively under-explored basin and lies about 150 km south of Cairo. The major goal of this study is to evaluate the source rock by using different techniques as Rock-Eval pyrolysis, Vitrinite reflectance (%Ro, and well log data of some Cretaceous sequences including Abu Roash (E, F and G members, Kharita and Betty formations. The BasinMod 1D program is used in this study to construct the burial history and calculate the levels of thermal maturity of the Fayoum-1X well based on calibration of measured %Ro and Tmax against calculated %Ro model. The calculated Total Organic Carbon (TOC content from well log data compared with the measured TOC from the Rock-Eval pyrolysis in Fayoum-1X well is shown to match against the shale source rock but gives high values against the limestone source rock. For that, a new model is derived from well log data to calculate accurately the TOC content against the limestone source rock in the study area. The organic matter existing in Abu Roash (F member is fair to excellent and capable of generating a significant amount of hydrocarbons (oil prone produced from (mixed type I/II kerogen. The generation potential of kerogen in Abu Roash (E and G members and Betty formations is ranging from poor to fair, and generating hydrocarbons of oil and gas prone (mixed type II/III kerogen. Eventually, kerogen (type III of Kharita Formation has poor to very good generation potential and mainly produces gas. Thermal maturation of the measured %Ro, calculated %Ro model, Tmax and Production index (PI indicates that Abu Roash (F member exciting in the onset of oil generation, whereas Abu Roash (E and G members, Kharita and Betty formations entered the peak of oil generation.

  2. Economical benzene emission reduction

    International Nuclear Information System (INIS)

    Schuetz, R.

    1999-01-01

    Benzene has been classified as a toxic compound under the Canadian Environmental Protection Act. This has prompted the Alberta Energy and Utilities Board (AEUB) to introduce specific reporting and monitoring guidelines for the oil and gas industry regarding excessive benzene emissions. Glycol dehydration units have been determined to be the major single source of benzene emissions causing air and soil pollution. DualTank Corp. has designed a condensation and storage tank unit to enhance emission reduction, odour elimination and liquid recovery from dehydration units. Their newly designed combined tank unit consists of a large, uninsulated surface area for cooling, and an excessive internal volume for increased retention time. The first prototype was installed in December 1998 at an Enerplus Resources Site. The system provides excellent benzene emission reduction and the elimination of odours and visual plumes. Effective January 1, 1999, the petroleum and natural gas industry must either clean up excessive emissions voluntarily or face government imposed regulations, facility shutdowns and/or fines. 1 fig

  3. Islam and harm reduction.

    Science.gov (United States)

    Kamarulzaman, A; Saifuddeen, S M

    2010-03-01

    Although drugs are haram and therefore prohibited in Islam, illicit drug use is widespread in many Islamic countries throughout the world. In the last several years increased prevalence of this problem has been observed in many of these countries which has in turn led to increasing injecting drug use driven HIV/AIDS epidemic across the Islamic world. Whilst some countries have recently responded to the threat through the implementation of harm reduction programmes, many others have been slow to respond. In Islam, The Quran and the Prophetic traditions or the Sunnah are the central sources of references for the laws and principles that guide the Muslims' way of life and by which policies and guidelines for responses including that of contemporary social and health problems can be derived. The preservation and protection of the dignity of man, and steering mankind away from harm and destruction are central to the teachings of Islam. When viewed through the Islamic principles of the preservation and protection of the faith, life, intellect, progeny and wealth, harm reduction programmes are permissible and in fact provide a practical solution to a problem that could result in far greater damage to the society at large if left unaddressed. Copyright (c) 2009. Published by Elsevier B.V.

  4. 76 FR 46290 - EPA Seeking Input Materials Measurement; Municipal Solid Waste (MSW), Recycling, and Source...

    Science.gov (United States)

    2011-08-02

    ... States'' as part of a broader discussion about sustainable materials management. This information will be..., as well as its transparency. There is also a growing need for a more holistic assessment of how... sustainable management of these materials through safe recycling and source reduction. The Agency will...

  5. Finding optimal exact reducts

    KAUST Repository

    AbouEisha, Hassan M.

    2014-01-01

    The problem of attribute reduction is an important problem related to feature selection and knowledge discovery. The problem of finding reducts with minimum cardinality is NP-hard. This paper suggests a new algorithm for finding exact reducts

  6. LOFT data reduction

    International Nuclear Information System (INIS)

    Norman, N.L.

    1975-08-01

    The Loss-of-Fluid Test (LOFT) Facility is an experimental facility built around a ''scaled'' version of a large pressurized water reactor (LPWR). LOFT will be used to run loss-of-coolant experiments (LOCEs) and to acquire the necessary data required ''to evaluate the adequacy and improve the analytical methods currently used to predict the loss-of-coolant accident (LOCA) response of LPWRs'' and ''to identify and investigate any unexpected event(s) or threshold(s) in the response of either the plant or the engineered safety features and develop analytical techniques that adequately describe and account for the unexpected behavior(s)''. During the LOCE this required data will be acquired and recorded in both analog and digital modes. Subsequent to the test the analog data will also be converted to the raw digital mode. This raw digital data will be converted to the desired engineering units using the LOFT Data Reduction System. This system is implemented on the IBM 360/75 and is a part of a commercially available data processing program called MAC/RAN III. The theory of reducing LOFT data to engineering units and the application of the MAC/ RAN III system to accomplish this reduction is given. (auth)

  7. Ninth wood energy symposium - Reduction of fine-dust emissions and power generation as part of a future power supply system; 9. Holzenergie-Symposium - Feinstaubminderung und Stromerzeugung im Rahmen der zukuenftigen Energieversorgung

    Energy Technology Data Exchange (ETDEWEB)

    Nussbaumer, T. (ed.)

    2006-07-01

    This comprehensive report is published by the Swiss Federal Office of Energy (SFOE). A total of fourteen papers were presented at the symposium on the following subjects: Federal Action-Plan in the wood-firing area and emission limits, Fair-Firing - an Action Plan for the prevention of increased emissions and illegal incineration of wastes, fine-dust from wood-fired systems in comparison with diesel soot from the health point of view, practical experience with low-particle, pellets-fired systems, basics and technologies for the precipitation of fine-dust and the influence of particle characteristics and mode of operation as well as two papers on the development of electrical precipitators for wood-fired systems from 200 kW upwards and the practical experience gained with them. Further, papers are presented that deal with small-size electrostatic precipitators, flameless combustion for NO{sub x} reduction and modern pellets technology. The potential and economic viability of wood fuels for the generation of electricity are discussed and a 7 MW{sub e} wood-fired power station is looked at. Finally, the options open for providing a secure supply of energy in Europe are discussed and the role to be played by biomass is examined.

  8. Breast Reduction Surgery

    Science.gov (United States)

    ... considering breast reduction surgery, consult a board-certified plastic surgeon. It's important to understand what breast reduction surgery entails — including possible risks and complications — as ...

  9. 10 years and 20,000 sources: the GTRI offsite source recovery project

    International Nuclear Information System (INIS)

    Whitworth, Julia; Streeper, Charles; Cuthbertson, Abigail

    2009-01-01

    Full text: The Global Threat Reduction Initiative's (GTRI) Offsite Source Recovery Project (OSRP) has been recovering excess and unwanted radioactive sealed sources for ten years. In January 2009, GTRI announced that the project had recovered 20,000 sealed radioactive sources. This project grew out of early efforts at Los Alamos National Laboratory (LANL) to recover and disposition excess Plutonium-239 ( 239 Pu) sealed sources that were distributed in the 1960s and 1970s under the Atoms for Peace Program. Decades later, these sources began to exceed their design life or fall out of regular use. Sealed source recovery was initially considered a waste management activity, but after the terrorist attacks of 2001, the interagency community began to recognize the threat posed by excess and unwanted radiological materials, particularly those that could not be disposed at the end of their useful life. After being transferred to the U.S. National Nuclear Security Administration (NNSA) to be part of GTRI, OSRP's mission was expanded to include not only material that would be classified as Greater-than-Class-C (GTCC) when it became waste, but also any other materials that might constitute a 'national security consideration'. This paper discusses OSRP's history, recovery operations, expansion to accept high-activity beta-gamma-emitting sealed sources and devices and foreign-possessed sources, and more recent efforts such as involvement in GTRI's Search and Secure project. Current challenges and future work will also be discussed

  10. Efficacy studies of Reactive Skin Decontamination Lotion, M291 Skin Decontamination Kit, 0.5% bleach, 1% soapy water, and Skin Exposure Reduction Paste Against Chemical Warfare Agents, part 2: guinea pigs challenged with soman.

    Science.gov (United States)

    Braue, Ernest H; Smith, Kelly H; Doxzon, Bryce F; Lumpkin, Horace L; Clarkson, Edward D

    2011-03-01

    This report, the second in a series of five, directly compares the efficacy of Reactive Skin Decontamination Lotion (RSDL), the M291 Skin Decontamination Kit (SDK), 0.5% bleach (sodium or calcium hypochlorite solution), 1% soapy water, and Skin Exposure Reduction Paste Against Chemical Warfare Agents (SERPACWA) in the haired guinea pig model following exposure to soman (GD). In all experiments, guinea pigs were close-clipped and given anesthesia. In the decontamination experiments, the animals were challenged with GD and decontaminated after a 2-minute delay for the standard procedure or at longer times for the delayed-decontamination experiments. Positive control animals were challenged with GD in the same manner as the treated animals, except that they received no treatment. All animals were observed during the first 4 hours and again at 24 hours after exposure for signs of toxicity and death. The protective ratio (PR, defined as the median lethal dose [LD(50)] of the treatment group divided by the LD(50) of the untreated positive control animals) was calculated from the derived probit dose-response curves established for each treatment group and nontreated control animals. SERPACWA was applied as a thin coating (0.1 mm thick), allowed to dry for 15 minutes, and challenged with GD. After a 2-hour challenge, any remaining GD was blotted off the animal, but no additional decontamination was done. Significance in this report is defined as p decontamination experiments, the calculated PRs for RSDL, 0.5% bleach, 1% soapy water, and M291 SDK were 14, 2.7, 2.2, and 2.6, respectively. RSDL was by far the most effective decontamination product tested and significantly better than any of the other products. Bleach, soapy water, and the M291 SDK provided equivalent and modest protection. Since only RSDL provided at least good protection (PR > 5), it was the only decontamination product evaluated for delayed decontamination. In the GD delayed-decontamination experiments

  11. The Fate of the Iliopsoas Muscle in Long-term Follow-up After Open Reduction With a Medial Approach in Developmental Dysplasia of the Hip. Part 2: Isokinetic Muscle Strength Evaluation.

    Science.gov (United States)

    Yilmaz, Serdar; Aksahin, Ertugrul; Ersoz, Murat; Bicimoglu, Ali

    2017-09-01

    The impact on long-term weakness of hip flexion of complete iliopsoas tenotomy during open reduction of developmental hip dysplasia with a medial approach has not yet been fully clarified. The purpose of this study was to investigate the isokinetic muscle strength (IMS) of hip flexor and extensor muscles in these patients and also to analyze the effect of spontaneous reattachment of the iliopsoas muscle on IMS measurements. The study included 20 patients. Earlier magnetic resonance imaging examination of all the patients revealed spontaneous reattachment of the iliopsoas in 18 (90%) patients. IMS measurements were performed at 60 and 150 degrees/s. The peak torque, total work (TW), average power (AP), work fatigue, and agonist to antagonist muscle ratio of the operated and nonoperated hips were recorded separately for flexors and extensors. The effect of iliopsoas reattachment on IMS was also evaluated. The mean follow-up period was 16.65±2.16 (13 to 20) years. Total work (P=0.013) and average power (P=0.009) of the flexor muscles and work fatigue of the extensor muscles (P=0.030) of the operated hip were significantly decreased when compared with the nonoperated hips at 150 degrees/s. There was no significant difference between the flexor muscles of the operated and nonoperated hips (Phips. Flexor muscle strength was decreased in the operated hip against low resistance in long-term follow-up after iliopsoas tenotomy. This may reflect that hip muscle strength was decreased after prolonged activities such as sports. However, in forceful activities flexor muscle strength was retained due to iliopsoas reattachment. On the basis of this study we thought that spontaneous reattachment of the iliopsoas tendon substantially preserves muscle strength. Nonetheless possible efforts should be made to surgically reattach the psoas tendon to preserve strength of the muscle. Therapeutic level IV.

  12. Generation, ascent and eruption of magma on the Moon: New insights into source depths, magma supply, intrusions and effusive/explosive eruptions (Part 2: Predicted emplacement processes and observations)

    Science.gov (United States)

    Head, James W.; Wilson, Lionel

    2017-02-01

    We utilize a theoretical analysis of the generation, ascent, intrusion and eruption of basaltic magma on the Moon to develop new insights into magma source depths, supply processes, transport and emplacement mechanisms via dike intrusions, and effusive and explosive eruptions. We make predictions about the intrusion and eruption processes and compare these with the range of observed styles of mare volcanism, and related features and deposits. Density contrasts between the bulk mantle and regions with a greater abundance of heat sources will cause larger heated regions to rise as buoyant melt-rich diapirs that generate partial melts that can undergo collection into magma source regions; diapirs rise to the base of the anorthositic crustal density trap (when the crust is thicker than the elastic lithosphere) or, later in history, to the base of the lithospheric rheological trap (when the thickening lithosphere exceeds the thickness of the crust). Residual diapiric buoyancy, and continued production and arrival of diapiric material, enhances melt volume and overpressurizes the source regions, producing sufficient stress to cause brittle deformation of the elastic part of the overlying lithosphere; a magma-filled crack initiates and propagates toward the surface as a convex upward, blade-shaped dike. The volume of magma released in a single event is likely to lie in the range 102 km3 to 103 km3, corresponding to dikes with widths of 40-100 m and both vertical and horizontal extents of 60-100 km, favoring eruption on the lunar nearside. Shallower magma sources produce dikes that are continuous from the source region to the surface, but deeper sources will propagate dikes that detach from the source region and ascend as discrete penny-shaped structures. As the Moon cools with time, the lithosphere thickens, source regions become less abundant, and rheological traps become increasingly deep; the state of stress in the lithosphere becomes increasingly contractional

  13. Reference Sources in Chemistry

    OpenAIRE

    Sthapit, Dilip Man

    1995-01-01

    Information plays an important role in the development of every field. Therefore a brief knowledge regarding information sources is necessary to function in any field. There are many information sources about scientific and technical subjects. In this context there are many reference sources in Chemistry too. Chemistry is one important part of the science which deals with the study of the composition of substances and the chemical changes that they undergo. The purpose of this report is...

  14. Active Vibration Control for Helicopter Interior Noise Reduction Using Power Minimization

    Science.gov (United States)

    Mendoza, J.; Chevva, K.; Sun, F.; Blanc, A.; Kim, S. B.

    2014-01-01

    This report describes work performed by United Technologies Research Center (UTRC) for NASA Langley Research Center (LaRC) under Contract NNL11AA06C. The objective of this program is to develop technology to reduce helicopter interior noise resulting from multiple gear meshing frequencies. A novel active vibration control approach called Minimum Actuation Power (MAP) is developed. MAP is an optimal control strategy that minimizes the total input power into a structure by monitoring and varying the input power of controlling sources. MAP control was implemented without explicit knowledge of the phasing and magnitude of the excitation sources by driving the real part of the input power from the controlling sources to zero. It is shown that this occurs when the total mechanical input power from the excitation and controlling sources is a minimum. MAP theory is developed for multiple excitation sources with arbitrary relative phasing for single or multiple discrete frequencies and controlled by a single or multiple controlling sources. Simulations and experimental results demonstrate the feasibility of MAP for structural vibration reduction of a realistic rotorcraft interior structure. MAP control resulted in significant average global vibration reduction of a single frequency and multiple frequency excitations with one controlling actuator. Simulations also demonstrate the potential effectiveness of the observed vibration reductions on interior radiated noise.

  15. Microbial reduction of iron ore

    Science.gov (United States)

    Hoffmann, M.R.; Arnold, R.G.; Stephanopoulos, G.

    1989-11-14

    A process is provided for reducing iron ore by treatment with microorganisms which comprises forming an aqueous mixture of iron ore, microorganisms operable for reducing the ferric iron of the iron ore to ferrous iron, and a substrate operable as an energy source for the microbial reduction; and maintaining the aqueous mixture for a period of time and under conditions operable to effect the reduction of the ore. Preferably the microorganism is Pseudomonas sp. 200 and the reduction conducted anaerobically with a domestic wastewater as the substrate. An aqueous solution containing soluble ferrous iron can be separated from the reacted mixture, treated with a base to precipitate ferrous hydroxide which can then be recovered as a concentrated slurry. 11 figs.

  16. Twitter as a Potential Disaster Risk Reduction Tool. Part III: Evaluating Variables that Promoted Regional Twitter Use for At-risk Populations During the 2013 Hattiesburg F4 Tornado.

    Science.gov (United States)

    Cooper, Guy Paul; Yeager, Violet; Burkle, Frederick M; Subbarao, Italo

    2015-06-29

    Study goals attempt to identify the variables most commonly associated with successful tweeted messages and determine which variables have the most influence in promoting exponential dissemination of information (viral spreading of the message) and trending (becoming popular) in the given disaster affected region. Part II describes the detailed extraction and triangulation filtration methodological approach to acquiring twitter data for the 2013 Hattiesburg Tornado. The data was then divided into two 48 hour windows before and after the tornado impact with a 2 hour pre-tornado buffer to capture tweets just prior to impact. Criteria-based analysis was completed for Tweets and users. The top 100 pre-Tornado and post-Tornado retweeted users were compared to establish the variability among the top retweeted users during the 4 day span.  Pre-Tornado variables that were correlated to higher retweeted rates include total user tweets (0.324), and total times message retweeted (0.530).  Post-Tornado variables that were correlated to higher retweeted rates include total hashtags in a retweet (0.538) and hashtags #Tornado (0.378) and #Hattiesburg (0.254). Overall hashtags usage significantly increased during the storm. Pre-storm there were 5,763 tweets with a hashtag and post-storm there was 13,598 using hashtags. Twitter's unique features allow it to be considered a unique social media tool applicable for emergency managers and public health officials for rapid and accurate two way communication.  Additionally, understanding how variables can be properly manipulated plays a key role in understanding how to use this social media platform for effective, accurate, and rapid mass information communication.

  17. Infinitary Combinatory Reduction Systems: Normalising Reduction Strategies

    NARCIS (Netherlands)

    Ketema, J.; Simonsen, Jakob Grue

    2010-01-01

    We study normalising reduction strategies for infinitary Combinatory Reduction Systems (iCRSs). We prove that all fair, outermost-fair, and needed-fair strategies are normalising for orthogonal, fully-extended iCRSs. These facts properly generalise a number of results on normalising strategies in

  18. Motorcycle Parts

    Science.gov (United States)

    1993-01-01

    An article in NASA Tech Briefs describing a vacuum bagging process for forming composite parts helped a small Oklahoma Company to improve its manufacturing process. President of Performance Extremes, Larry Ortega, and his partners make motorcycle parts from carbon/epoxy to reduce weight. Using vacuum bags, parts have a better surface and fewer voids inside. When heat used in the vacuum bag process caused deformation upon cooling, a solution found in another tech brief solved the problem. A metal plate inside the vacuum bag made for more even heat transfer. A third article described a simple procedure for repairing loose connector pins, which the company has also utilized.

  19. Active sound reduction system and method

    NARCIS (Netherlands)

    2016-01-01

    The present invention refers to an active sound reduction system and method for attenuation of sound emitted by a primary sound source, especially for attenuation of snoring sounds emitted by a human being. This system comprises a primary sound source, at least one speaker as a secondary sound

  20. Hazardous material reduction initiative

    International Nuclear Information System (INIS)

    Nichols, D.H.

    1995-02-01

    The Hazardous Material Reduction Initiative (HMRI) explores using the review of purchase requisitions to reduce both the use of hazardous materials and the generation of regulated and nonregulated wastes. Based on an 11-month program implemented at the Hanford Site, hazardous material use and waste generation was effectively reduced by using a centralized procurement control program known as HMRI. As expected, several changes to the original proposal were needed during the development/testing phase of the program to accommodate changing and actual conditions found at the Hanford Site. The current method requires a central receiving point within the Procurement Organization to review all purchase requisitions for potentially Occupational Safety and Health Administration (OSHA) hazardous products. Those requisitions (approximately 4% to 6% of the total) are then forwarded to Pollution Prevention personnel for evaluation under HMRI. The first step is to determine if the requested item can be filled by existing or surplus material. The requisitions that cannot filled by existing or surplus material are then sorted into two groups based on applicability to the HMRI project. For example, laboratory requests for analytical reagents or standards are excluded and the purchase requisitions are returned to Procurement for normal processing because, although regulated, there is little opportunity for source reduction due to the strict protocols followed. Each item is then checked to determine if it is regulated or not. Regulated items are prioritized based on hazardous contents, quantity requested, and end use. Copies of these requisitions are made and the originals are returned to Procurement within 1-hr. Since changes to the requisition can be made at later stages during procurement, the HMRI fulfills one of its original premises in that it does not slow the procurement process

  1. New software for neutron data reduction and visualization

    International Nuclear Information System (INIS)

    Worlton, T.; Chatterjee, A.; Hammonds, J.; Chen, D.; Loong, C.K.; Mikkelson, D.; Mikkelson, R.

    2001-01-01

    Development of advanced neutron sources and instruments has necessitated corresponding advances in software for neutron scattering data reduction and visualization. New sources produce datasets more rapidly, and new instruments produce large numbers of spectra. Because of the shorter collection times, users are able to make more measurements on a given sample. This rapid production of datasets requires that users be able to reduce and analyze data quickly to prevent a data bottleneck. In addition, the new sources and instruments are accommodating more users with less neutron-scattering specific expertise, which requires software that is easy to use and freely available. We have developed an Integrated Spectral Analysis Workbench (ISAW) software package to permit the rapid reduction and visualization of neutron data. It can handle large numbers of spectra and merge data from separate measurements. The data can be sorted according to any attribute and transformed in numerous ways. ISAW provides several views of the data that enable users to compare spectra and observe trends in the data. A command interpreter, which is now part of ISAW, allows scientists to easily set up a series of instrument-specific operations to reduce and visualize data automatically. ISAW is written entirely in Java to permit portability to different computer platforms and easy distribution of the software. The software was constructed using modern computer design methods to allow easy customization and improvement. ISAW currently only reads data from IPNS 'run' files, but work is underway to provide input of NeXus files. (author)

  2. New software for neutron data reduction and visualization

    Energy Technology Data Exchange (ETDEWEB)

    Worlton, T.; Chatterjee, A.; Hammonds, J.; Chen, D.; Loong, C.K. [Argonne National Laboratory, Argonne, IL (United States); Mikkelson, D.; Mikkelson, R. [Univ. of Wisconsin-Stout, Menomonie, WI (United States)

    2001-03-01

    Development of advanced neutron sources and instruments has necessitated corresponding advances in software for neutron scattering data reduction and visualization. New sources produce datasets more rapidly, and new instruments produce large numbers of spectra. Because of the shorter collection times, users are able to make more measurements on a given sample. This rapid production of datasets requires that users be able to reduce and analyze data quickly to prevent a data bottleneck. In addition, the new sources and instruments are accommodating more users with less neutron-scattering specific expertise, which requires software that is easy to use and freely available. We have developed an Integrated Spectral Analysis Workbench (ISAW) software package to permit the rapid reduction and visualization of neutron data. It can handle large numbers of spectra and merge data from separate measurements. The data can be sorted according to any attribute and transformed in numerous ways. ISAW provides several views of the data that enable users to compare spectra and observe trends in the data. A command interpreter, which is now part of ISAW, allows scientists to easily set up a series of instrument-specific operations to reduce and visualize data automatically. ISAW is written entirely in Java to permit portability to different computer platforms and easy distribution of the software. The software was constructed using modern computer design methods to allow easy customization and improvement. ISAW currently only reads data from IPNS 'run' files, but work is underway to provide input of NeXus files. (author)

  3. Reduction in language testing

    DEFF Research Database (Denmark)

    Dimova, Slobodanka; Jensen, Christian

    2013-01-01

    /video recorded speech samples and written reports produced by two experienced raters after testing. Our findings suggest that reduction or reduction-like pronunciation features are found in tested L2 speech, but whenever raters identify and comment on such reductions, they tend to assess reductions negatively......This study represents an initial exploration of raters' comments and actual realisations of form reductions in L2 test speech performances. Performances of three L2 speakers were selected as case studies and illustrations of how reductions are evaluated by the raters. The analysis is based on audio...

  4. Microplastics pollution and reduction strategies

    Institute of Scientific and Technical Information of China (English)

    Wei-Min Wu; Jun Yang; Craig S.Criddle

    2017-01-01

    Microplastic particles smaller than 5 mm in size are of increasing concern,especially in aquatic environments,such as the ocean.Primary source is microbeads (< 1 mm) used in cosmetics and cleaning agents and fiber fragments from washing of clothes,and secondary source such as broken down plastic litter and debris.These particles are mostly made from polyethylene (PE),polypropylene (PP),polystyrene (PS),polyethylene terephthalate (PET) and polyesters.They are ingested by diverse marine fauna,including zooplanktons,mussel,oyster,shrimp,fish etc.and can enter human food chains via several pathways.Strategy for control of microplastics pollution should primarily focus on source reduction and subsequently on the development of cost-effective clean up and remediation technologies.Recent research results on biodegradation of plastics have revealed a potential for microbial biodegradation and bioremediation of plastic pollutants,such as PE,PS and PET under appropriate conditions.

  5. Sulfate reduction in freshwater peatlands

    Energy Technology Data Exchange (ETDEWEB)

    Oequist, M.

    1996-12-31

    This text consist of two parts: Part A is a literature review on microbial sulfate reduction with emphasis on freshwater peatlands, and part B presents the results from a study of the relative importance of sulfate reduction and methane formation for the anaerobic decomposition in a boreal peatland. The relative importance of sulfate reduction and methane production for the anaerobic decomposition was studied in a small raised bog situated in the boreal zone of southern Sweden. Depth distribution of sulfate reduction- and methane production rates were measured in peat sampled from three sites (A, B, and C) forming an minerotrophic-ombrotrophic gradient. SO{sub 4}{sup 2-} concentrations in the three profiles were of equal magnitude and ranged from 50 to 150 {mu}M. In contrast, rates of sulfate reduction were vastly different: Maximum rates in the three profiles were obtained at a depth of ca. 20 cm below the water table. In A it was 8 {mu}M h{sup -1} while in B and C they were 1 and 0.05 {mu}M h{sup -1}, respectively. Methane production rates, however, were more uniform across the three nutrient regimes. Maximum rates in A (ca. 1.5 {mu}g d{sup -1} g{sup -1}) were found 10 cm below the water table, in B (ca. 1.0 {mu}g d{sup -1} g{sup -1}) in the vicinity of the water table, and in C (0.75 {mu}g d{sup -1} g{sup -1}) 20 cm below the water table. In all profiles both sulfate reduction and methane production rates were negligible above the water table. The areal estimates of methane production for the profiles were 22.4, 9.0 and 6.4 mmol m{sup -2} d{sup -1}, while the estimates for sulfate reduction were 26.4, 2.5, and 0.1 mmol m{sup -2} d{sup -1}, respectively. The calculated turnover times at the sites were 1.2, 14.2, and 198.7 days, respectively. The study shows that sulfate reducing bacteria are important for the anaerobic degradation in the studied peatland, especially in the minerotrophic sites, while methanogenic bacteria dominate in ombrotrophic sites Examination

  6. Sulfate reduction in freshwater peatlands

    International Nuclear Information System (INIS)

    Oequist, M.

    1996-01-01

    This text consist of two parts: Part A is a literature review on microbial sulfate reduction with emphasis on freshwater peatlands, and part B presents the results from a study of the relative importance of sulfate reduction and methane formation for the anaerobic decomposition in a boreal peatland. The relative importance of sulfate reduction and methane production for the anaerobic decomposition was studied in a small raised bog situated in the boreal zone of southern Sweden. Depth distribution of sulfate reduction- and methane production rates were measured in peat sampled from three sites (A, B, and C) forming an minerotrophic-ombrotrophic gradient. SO 4 2- concentrations in the three profiles were of equal magnitude and ranged from 50 to 150 μM. In contrast, rates of sulfate reduction were vastly different: Maximum rates in the three profiles were obtained at a depth of ca. 20 cm below the water table. In A it was 8 μM h -1 while in B and C they were 1 and 0.05 μM h -1 , respectively. Methane production rates, however, were more uniform across the three nutrient regimes. Maximum rates in A (ca. 1.5 μg d -1 g -1 ) were found 10 cm below the water table, in B (ca. 1.0 μg d -1 g -1 ) in the vicinity of the water table, and in C (0.75 μg d -1 g -1 ) 20 cm below the water table. In all profiles both sulfate reduction and methane production rates were negligible above the water table. The areal estimates of methane production for the profiles were 22.4, 9.0 and 6.4 mmol m -2 d -1 , while the estimates for sulfate reduction were 26.4, 2.5, and 0.1 mmol m -2 d -1 , respectively. The calculated turnover times at the sites were 1.2, 14.2, and 198.7 days, respectively. The study shows that sulfate reducing bacteria are important for the anaerobic degradation in the studied peatland, especially in the minerotrophic sites, while methanogenic bacteria dominate in ombrotrophic sites Examination paper. 67 refs, 6 figs, 3 tabs

  7. Technical considerations in snubber reduction programs

    International Nuclear Information System (INIS)

    Longo, D.L.; Kitz, G.T.

    1989-01-01

    Snubber reduction has been a much discussed topic for the past several years. The advantages to the owner in terms of reduced radiation exposure, lower operating costs, and better plant maintainability are obvious but difficult to quantify. The costs associated with performing a snubber reduction program can be quantified, but can vary widely depending on how the program is implemented. One approach is to divide the scope of the work into several parts, based on similarities and differences of the plant systems and technical requirements. for example, for this program, the work was divided into three parts: nuclear steam supply system, torus-attached piping, and balance of plant. This approach facilitates addressing the variations in design requirements and the variations in snubber removal priorities that are related to each plant segment. It also allows the experience gained in the first part to be applied to the subsequent parts. This paper describes one utility's experience in successfully completing two parts of a three-part snubber reduction program and focuses on the various technical issues that must be addressed along with those areas where the utility should establish checkpoints that are critical to the success of the overall program. It also describes how the experience from the first two parts will be factored into the final part of the snubber reduction program

  8. The national-economic cost of reduction of greenhouse gases emission. Comparison of investments aimed towards a reduced greenhouse gas emission in power industry, agriculture, transportation sector and other essential greenhouse gas sources

    International Nuclear Information System (INIS)

    1995-01-01

    For a number of years the cost of reducing CO 2 emissions in the energy sector in Denmark has been investigated in detail. The same has not been the case what concerns the cost of reducing other greenhouse gases (CH 4 and N 2 O) and especially not what concerns the possibilities of reducing greenhouse gases in other sectors in the Danish economy, i.e. agriculture, transport, industry, domestic waste and forestry. Thus, the objective of this project was twofold: 1) To calculate the national economic costs related to a number of options for reducing Danish greenhouse gas emissions (CO 2 , CH 4 and N 2 O) by using the same methodology for all important sectors in the economy and 2) To compare the cost efficiency of these options not only wihtin the individual sectors but also across the sectoral boundaries to achieve an overall view of the reduction possibilities in society and the associated costs. (au) 80 refs.; Prepared by Forskningscenter Risoe and Danmarks Miljoeundersoegelser. Afdeling for Systemanalyse

  9. MCNP variance reduction overview

    International Nuclear Information System (INIS)

    Hendricks, J.S.; Booth, T.E.

    1985-01-01

    The MCNP code is rich in variance reduction features. Standard variance reduction methods found in most Monte Carlo codes are available as well as a number of methods unique to MCNP. We discuss the variance reduction features presently in MCNP as well as new ones under study for possible inclusion in future versions of the code

  10. Modern Reduction Methods

    CERN Document Server

    Andersson, Pher G

    2008-01-01

    With its comprehensive overview of modern reduction methods, this book features high quality contributions allowing readers to find reliable solutions quickly and easily. The monograph treats the reduction of carbonyles, alkenes, imines and alkynes, as well as reductive aminations and cross and heck couplings, before finishing off with sections on kinetic resolutions and hydrogenolysis. An indispensable lab companion for every chemist.

  11. Global Sourcing Flexibility

    DEFF Research Database (Denmark)

    Ørberg Jensen, Peter D.; Petersen, Bent

    2013-01-01

    the higher costs (but decreased risk for value chain disruption) embedded in a more flexible global sourcing model that allows the firm to replicate and/or relocate activities across multiple locations. We develop a model and propositions on facilitating and constraining conditions of global sourcing...... sourcing flexibility. Here we draw on prior research in the fields of organizational flexibility, international business and global sourcing as well as case examples and secondary studies. In the second part of the paper, we discuss the implications of global sourcing flexibility for firm strategy...... and operations against the backdrop of the theory-based definition of the construct. We discuss in particular the importance of global sourcing flexibility for operational performance stability, and the trade-off between specialization benefits, emerging from location and service provider specialization, versus...

  12. Hybrid ground-source heat pump system with active air source regeneration

    International Nuclear Information System (INIS)

    Allaerts, K.; Coomans, M.; Salenbien, R.

    2015-01-01

    Highlights: • A hybrid ground source heat pump system with two separate borefields is modelled. • The maximum underground storage temperature depends on the size of the drycooler. • Drycooler selection curves are given as function of underground storage temperature. • The size of the cold storage is reduced with 47% in the cost optimal configuration. • The cooling seasonal performance factor decreases with reduced storage capacity. - Abstract: Ground-source heat pump systems (GSHP) offer great advantages over traditional heating and cooling installations. However, their applications are limited due to the high initial costs of borehole drilling. One way to avoid these costs is by reducing the size of the borefield, e.g. by combining the system with other renewable energy sources or by using active regeneration to increase the system efficiency. In this paper a hybrid ground-source heat pump system (HGSHP) is analyzed. The borefield is split into a warm part and a cold part, which allows for seasonal thermal-energy storage. Additionally, supplementary drycoolers capture heat during summer and cold during winter. The relationship between the underground storage size and temperature and the drycooler capacity is described, using an office building in Flanders (Belgium) as reference case. Results show that with a HGSHP system a significant borefield size reduction can be achieved without compromising system performance; i.e. for the reference case a reduction of 47% was achieved in the cost-optimal configuration. It is also shown that the cooling seasonal performance factor decreases significantly with underground storage capacity. In addition, the HGSHP can be used to maintain or restore thermal balance in the geothermal source when heating and cooling loads do not match

  13. Interventions for Stigma ReductionPart 2: Practical Applications

    Directory of Open Access Journals (Sweden)

    Ajit Dalal

    2012-02-01

    Full Text Available This paper reports the endeavours of the Working Group assigned to develop guidelines for interventions to reduce stigma. The group was comprised of academics and experienced field personnel, all of whom had either investigated stigma, implemented actions to address stigma, and/or had experienced stigma. The group’s mandate was to develop an intervention to reduce the stigma of leprosy, but while accepting that there are commonalities relating to stigma that cut across different health conditions, it was hoped that a generic intervention might be developed. This goal proved to be unattainable in the time given: condition-specific peculiarities and the diversity of cultural contexts presented significant challenges. The group agreed, however, that a considerable body of theory and expert opinion does exist, and that general strategies might be developed from this. The Working Group discussed a systematic review of such material. It also discussed other material that was considered to be important but had not met the criteria for the systematic review. One conclusion of the group’s deliberations was that a “Stigma Intervention Matrix” could be a useful guide for cross-checking the development of situation-specific stigma interventions. The Stigma Intervention Matrix is presented in this paper.DOI: 10.5463/dcid.v22i3.72

  14. CPS Transformation of Flow Information, Part II: Administrative Reductions

    DEFF Research Database (Denmark)

    Damian, Daniel; Danvy, Olivier

    2001-01-01

    the least solution. Preservation of least solutions solves a problem that was left open in Palsberg and Wand's article ‘CPS Transformation of Flow Information.’ Together, Palsberg and Wand's article and the present article show how to map in linear time the least solution of the flow constraints...

  15. Concepção e avaliação de uma unidade de peneiramento forçado para a redução do tamanho de partículas presentes no esgoto bruto doméstico Design and evaluation of a forced sieving unit (FSU for the reduction of the particle size present in raw domestic sewage

    Directory of Open Access Journals (Sweden)

    Ana Raquel Teixeira

    2009-09-01

    Full Text Available Este trabalho teve como objetivo a concepção e o teste de uma unidade de peneiramento forçado, utilizada para o pré-tratamento do esgoto bruto com vistas à redução do tamanho de partículas de matéria orgânica. A unidade de peneiramento forçado (UPF era constituída de uma peneira metálica (abertura de malha de 1 mm inserida na tubulação de recalque através da qual o esgoto efluente era bombeado. O peneiramento forçado resultou em maior concentração de partículas com diâmetro entre 1,8 e 30 µm, sem que houvesse retenção de material particulado. Todavia, a UPF não influenciou na redução/retenção de DQO TOTAL do esgoto bruto.The work focused on the conception and test of a forced sieving unit, used for the pre-treatment of raw sewage aiming at the reduction of organic matter particle size. The pre-treatment unit involved the use of a metallic sieve (1 mm cut-off assembled inside the pipeline through which the influent sewage was pumped. The results indicated that the forced sieving resulted in a higher concentration of particles with range diameter between 1.8 and 30 µm, without the retention of particulate material. However, the forced sieving unit did not influence the reduction/retention of COD TOTAL of the raw sewage.

  16. Part two

    DEFF Research Database (Denmark)

    Nielsen, Mads Pagh; Kær, Søren Knudsen; Korsgaard, Anders

    2008-01-01

    A novel micro combined heat and power system and a dynamic model thereof were presented in part one of the publication. In the following, the control system and dynamic performance of the system are presented. The model is subjected to a measured consumption pattern of 25 Danish single family...... houses with measurements of heat, power and hot water consumption every 15th minute during one year. Three scenarios are analyzed ranging from heat following only (grid compensation for electricity) to heat and power following with net export of electricity during high and peak load hours. Average...

  17. Source Water Protection Contaminant Sources

    Data.gov (United States)

    Iowa State University GIS Support and Research Facility — Simplified aggregation of potential contaminant sources used for Source Water Assessment and Protection. The data is derived from IDNR, IDALS, and US EPA program...

  18. An Optimization Mechanism Intended for Static Power Reduction Using Dual-thTechnique

    Directory of Open Access Journals (Sweden)

    Rodolfo P. Santos

    2012-01-01

    Full Text Available Power consumption reduction is a challenge nowadays. Techniques for dynamic and static power minimization have been proposed, but most of them are very time consuming. This work proposes an algorithm for reducing static power, which can be perfectly inserted in the conventional design flow for integrated systems considering an open source environment (open access infrastructure. The proposed approach, based on a Dual-Threshold technique, replaces part of the cells of the circuit by cells with a higher threshold voltage without resulting in timing violations in the circuit. The decision to replace a cell is based on timing estimates of the circuit modeling with the cell replacement, before it is actually replaced. The fact that only some cells are replaced every iteration results in a reduction of the runtime of the algorithm. Additionally, results showed a reduction in static power up to 39.28%, when applying the proposed approach in the ISCAS85 benchmark circuits.

  19. Reduction - competitive tomorrow

    International Nuclear Information System (INIS)

    Worley, L.; Bargerstock, S.

    1995-01-01

    Inventory reduction is one of the few initiatives that represent significant cost-reduction potential that does not result in personnel reduction. Centerior Energy's Perry nuclear power plant has embarked on an aggressive program to reduce inventory while maintaining plant material availability. Material availability to the plant was above 98%, but at an unacceptable 1994 inventory book value of $47 million with inventory carrying costs calculated at 30% annually

  20. Process energy reduction

    International Nuclear Information System (INIS)

    Lowthian, W.E.

    1993-01-01

    Process Energy Reduction (PER) is a demand-side energy reduction approach which complements and often supplants other traditional energy reduction methods such as conservation and heat recovery. Because the application of PER is less obvious than the traditional methods, it takes some time to learn the steps as well as practice to become proficient in its use. However, the benefit is significant, often far outweighing the traditional energy reduction approaches. Furthermore, the method usually results in a better process having less waste and pollution along with improved yields, increased capacity, and lower operating costs

  1. Finding optimal exact reducts

    KAUST Repository

    AbouEisha, Hassan M.

    2014-01-01

    The problem of attribute reduction is an important problem related to feature selection and knowledge discovery. The problem of finding reducts with minimum cardinality is NP-hard. This paper suggests a new algorithm for finding exact reducts with minimum cardinality. This algorithm transforms the initial table to a decision table of a special kind, apply a set of simplification steps to this table, and use a dynamic programming algorithm to finish the construction of an optimal reduct. I present results of computer experiments for a collection of decision tables from UCIML Repository. For many of the experimented tables, the simplification steps solved the problem.

  2. Metallothermic reduction of molybdate

    International Nuclear Information System (INIS)

    Mukherjee, T.K.; Bose, D.K.

    1987-01-01

    This paper gives a brief account of the investigations conducted so far on metallothermic reduction of high grade molybdenite with particular emphasis on the work carried out in Bhabha Atomic Research Centre. Based on thermochemical considerations, the paper first introduces a number of metallic reductants suitable for use in metallothermic reduction of molybdenite. Aluminium, sodium and tin are found to be suitable reducing agents and very rightly they have found most applications in the research and development efforts on metallothermic reduction of molybdenite. The reduction with tin was conducted on fairly large scale both in vacuum and hydrogen atmosphere. The reaction was reported to be invariant depending mainly on the reduction temperature and a temperature of the order of 1250deg to 1300degC was required for good metal recovery. In comparison to tin, aluminothermic reduction of molybdenite was studied more extensively and it was conducted in closed bomb, vacuum and also in open atmosphere. In aluminothermic reduction, the influence of amount of reducing agent, amount of heat booster, preheating temperature and charging procedure on these metal yield was studied in detail. The reduction generally yielded massive molybdenum metal contaminated with aluminium as the major impurity element. Efforts were made to purify the reduced metal by arc melting, electron beam melting and molten salt electrorefining. 9 refs. (author)

  3. 5 CFR 930.210 - Reduction in force.

    Science.gov (United States)

    2010-01-01

    ... 5 Administrative Personnel 2 2010-01-01 2010-01-01 false Reduction in force. 930.210 Section 930... § 930.210 Reduction in force. (a) Retention preference regulations. Except as modified by this section, the reduction in force regulations in part 351 of this chapter apply to administrative law judges. (b...

  4. Project identification for methane reduction options

    Energy Technology Data Exchange (ETDEWEB)

    Kerr, T.

    1996-12-31

    This paper discusses efforts directed at reduction in emission of methane to the atmosphere. Methane is a potent greenhouse gas, which on a 20 year timeframe may present a similar problem to carbon dioxide. In addition, methane causes additional problems in the form of smog and its longer atmospheric lifetime. The author discusses strategies for reducing methane emission from several major sources. This includes landfill methane recovery, coalbed methane recovery, livestock methane reduction - in the form of ruminant methane reduction and manure methane recovery. The author presents examples of projects which have implemented these ideas, the economics of the projects, and additional gains which come from the projects.

  5. Nitric oxide reduction over a synthetic coal char

    Energy Technology Data Exchange (ETDEWEB)

    C. Pevida; A. Arenillas; F. Rubiera; J.J. Pis [Instituto Nacional del Carbon, CSIC, Oviedo (Spain)

    2003-07-01

    In the present work, the mechanisms involved in the NO heterogeneous reduction have been investigated. A synthetic coal char was used as the carbon source. This synthetic coal was made from a mixture of model compounds and provides well-known functionalities, including nitrogenated ones, similar to those found in a high volatile bituminous coal. The char was obtained by pyrolysis of the synthetic coal, up to 1123 K, under helium atmosphere in a fixed bed reactor. Char texture and structure were characterised by N{sub 2} and CO{sub 2} adsorption isotherms at 77 and 273 K, respectively, X-ray diffraction, immersion calorimetry in C{sub 6}H{sub 6} and scanning electron microscopy (SEM). Temperature programmed reactions (TPR) were carried out in a thermogravimetric analyser using 400 ppm NO diluted in Ar as the reactant gas. The char was heated at 15 K min{sup -1} from room temperature to 1273 K. Gaseous products were simultaneously analysed by mass spectrometry (MS) and Fourier transform infrared spectroscopy (FTIR). The influence of nitrogen in the solid phase on the reduction mechanism was evaluated by comparing the results for chars with and without nitrogen in their composition. The results of this preliminary study showed that the presence of nitrogen in the chars composition did not favour the heterogeneous NO reduction. In addition, low temperature NO chemisorption on the carbon surface creates complexes that take an active part in the subsequent reactions with NO. 5 refs., 4 figs., 3 tabs.

  6. Development of multiampere negative ion sources

    International Nuclear Information System (INIS)

    Alessi, J.; Hershcovitch, A.; Prelec, K.; Sluyters, T.

    1981-01-01

    The Neutral Beam Development Group at BNL is developing H-/D- surface plasma sources as part of a high energy neutral beam injector. Uncooled Penning and magnetron sources have operated at a maximum beam current of 1 A (10 ms pulses, Mk III) and a maximum pulse length of 200 ms (0.3 A, Mk IV). A magnetron source with focusing grooves on the cathode and an asymmetric anode-cathode geometry operates at a power efficiency of 8 kW/A and a 6% gas efficiency. As the next step, a water cooled magnetron, designed to give a steady state beam of 1 to 2 A, has been constructed. Experiments are in progress to test a modification of the magnetron which may significantly improve its performance. By injecting a sheet of plasma, produced by a highly gas efficient hollow cathode discharge, into a magnetron type anode-cathode geometry, we anticipate a reduction of the source operating pressure by at least three orders of magnitude. Initial experiments have given indications of H - production. The next plasma injection experiment is designed to give a steady state beam of approx. = 1 A

  7. Positron sources

    International Nuclear Information System (INIS)

    Chehab, R.

    1994-01-01

    A tentative survey of positron sources is given. Physical processes on which positron generation is based are indicated and analyzed. Explanation of the general features of electromagnetic interactions and nuclear β + decay makes it possible to predict the yield and emittance for a given optical matching system between the positron source and the accelerator. Some kinds of matching systems commonly used - mainly working with solenoidal field - are studied and the acceptance volume calculated. Such knowledge is helpful in comparing different matching systems. Since for large machines, a significant distance exists between the positron source and the experimental facility, positron emittance has to be preserved during beam transfer over large distances and methods used for that purpose are indicated. Comparison of existing positron sources leads to extrapolation to sources for future linear colliders. Some new ideas associated with these sources are also presented. (orig.)

  8. PLAINS CO2 REDUCTION (PCOR) PARTNERSHIP

    Energy Technology Data Exchange (ETDEWEB)

    Edward N. Steadman; Daniel J. Daly; Lynette L. de Silva; John A. Harju; Melanie D. Jensen; Erin M. O' Leary; Wesley D. Peck; Steven A. Smith; James A. Sorensen

    2006-01-01

    During the period of October 1, 2003, through September 30, 2005, the Plains CO2 Reduction (PCOR) Partnership, identified geologic and terrestrial candidates for near-term practical and environmentally sound carbon dioxide (CO2) sequestration demonstrations in the heartland of North America. The PCOR Partnership region covered nine states and three Canadian provinces. The validation test candidates were further vetted to ensure that they represented projects with (1) commercial potential and (2) a mix that would support future projects both dependent and independent of CO2 monetization. This report uses the findings contained in the PCOR Partnership's two dozen topical reports and half-dozen fact sheets as well as the capabilities of its geographic information system-based Decision Support System to provide a concise picture of the sequestration potential for both terrestrial and geologic sequestration in the PCOR Partnership region based on assessments of sources, sinks, regulations, deployment issues, transportation, and capture and separation. The report also includes concise action plans for deployment and public education and outreach as well as a brief overview of the structure, development, and capabilities of the PCOR Partnership. The PCOR Partnership is one of seven regional partnerships under Phase I of the U.S. Department of Energy National Energy Technology Laboratory's Regional Carbon Sequestration Partnership program. The PCOR Partnership, comprising 49 public and private sector members, is led by the Energy & Environmental Research Center at the University of North Dakota. The international PCOR Partnership region includes the Canadian provinces of Alberta, Saskatchewan, and Manitoba and the states of Montana (part), Wyoming (part), North Dakota, South Dakota, Nebraska, Missouri, Iowa, Minnesota, and Wisconsin.

  9. Microbial reductive dehalogenation.

    Science.gov (United States)

    Mohn, W W; Tiedje, J M

    1992-01-01

    A wide variety of compounds can be biodegraded via reductive removal of halogen substituents. This process can degrade toxic pollutants, some of which are not known to be biodegraded by any other means. Reductive dehalogenation of aromatic compounds has been found primarily in undefined, syntrophic anaerobic communities. We discuss ecological and physiological principles which appear to be important in these communities and evaluate how widely applicable these principles are. Anaerobic communities that catalyze reductive dehalogenation appear to differ in many respects. A large number of pure cultures which catalyze reductive dehalogenation of aliphatic compounds are known, in contrast to only a few organisms which catalyze reductive dehalogenation of aromatic compounds. Desulfomonile tiedjei DCB-1 is an anaerobe which dehalogenates aromatic compounds and is physiologically and morphologically unusual in a number of respects, including the ability to exploit reductive dehalogenation for energy metabolism. When possible, we use D. tiedjei as a model to understand dehalogenating organisms in the above-mentioned undefined systems. Aerobes use reductive dehalogenation for substrates which are resistant to known mechanisms of oxidative attack. Reductive dehalogenation, especially of aliphatic compounds, has recently been found in cell-free systems. These systems give us an insight into how and why microorganisms catalyze this activity. In some cases transition metal complexes serve as catalysts, whereas in other cases, particularly with aromatic substrates, the catalysts appear to be enzymes. Images PMID:1406492

  10. Sources management

    International Nuclear Information System (INIS)

    Mansoux, H.; Gourmelon; Scanff, P.; Fournet, F.; Murith, Ch.; Saint-Paul, N.; Colson, P.; Jouve, A.; Feron, F.; Haranger, D.; Mathieu, P.; Paycha, F.; Israel, S.; Auboiroux, B.; Chartier, P.

    2005-01-01

    Organized by the section of technical protection of the French society of radiation protection ( S.F.R.P.), these two days had for objective to review the evolution of the rule relative to the sources of ionising radiations 'sealed and unsealed radioactive sources, electric generators'. They addressed all the actors concerned by the implementation of the new regulatory system in the different sectors of activities ( research, medicine and industry): Authorities, manufacturers, and suppliers of sources, holders and users, bodies involved in the approval of sources, carriers. (N.C.)

  11. New sources of radiation

    International Nuclear Information System (INIS)

    Schimmerling, W.

    1979-09-01

    An attempt is made to select examples of radiation sources whose application may make new or unconventional demands on radiation protection and dosimetry. A substantial body of knowledge about high energy facilities exists and, partly for this reason, the great high energy accelerators are mentioned only briefly

  12. Interpolation-Based Condensation Model Reduction Part 1: Frequency Window Reduction Method Application to Structural Acoustics

    National Research Council Canada - National Science Library

    Ingel, R

    1999-01-01

    ... (which require derivative information) interpolation functions as well as standard Lagrangian functions, which can be linear, quadratic or cubic, have been used to construct the interpolation windows...

  13. (segunda parte

    Directory of Open Access Journals (Sweden)

    José María Oliva-Martínez

    2004-01-01

    Full Text Available Este trabajo es la continuación de otro anterior (Oliva, 2004, ambos dedicados al estudio de la importancia del pensamiento analógico en la construcción histórica de la noción de fuerza gravitatoria y del modelo de Sistema Solar. En aquella ocasión analizamos dicho papel durante el período comprendido desde las antiguas civilizaciones hasta llegar a la revolución copernicana con científicos como Copérnico, Gilbert, Kepler o el propio Galileo. En esta segunda parte, se continúa con algunos de los razonamientos analógicos proporcionados desde la vertiente mecanicista, capitaneada por Descartes y desde la tradición subsiguiente que se desarrolló en línea con la utilización del método de la analogía como criterio argumentativo (Huyghens, Hooke, Bernoulli, etc.. Dedicamos asimismo un capítulo aparte a la figura de Newton, quien continúa con dicha tradición en su intento de explicar la naturaleza de la gravitación. Finalmente se procede, a modo de síntesis, a realizar una clasificación de distintos tipos de razonamientos analógicos aportados en el desarrollo histórico en torno a estos temas, estudiando el papel científico y divulgativo de cada uno

  14. Arctic Aerosols and Sources

    DEFF Research Database (Denmark)

    Nielsen, Ingeborg Elbæk

    2017-01-01

    Since the Industrial Revolution, the anthropogenic emission of greenhouse gases has been increasing, leading to a rise in the global temperature. Particularly in the Arctic, climate change is having serious impact where the average temperature has increased almost twice as much as the global during......, ammonium, black carbon, and trace metals. This PhD dissertation studies Arctic aerosols and their sources, with special focus on black carbon, attempting to increase the knowledge about aerosols’ effect on the climate in an Arctic content. The first part of the dissertation examines the diversity...... of aerosol emissions from an important anthropogenic aerosol source: residential wood combustion. The second part, characterizes the chemical and physical composition of aerosols while investigating sources of aerosols in the Arctic. The main instrument used in this research has been the state...

  15. Energy from biomass. Summaries of the Biomass Projects carried out as part of the Department of Trade and Industry's New and Renewable Energy Programme. Vol. 5: straw, poultry litter and energy crops as energy sources

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-01-01

    These volumes of summaries provide easy access to the many projects carried out in the Energy from Biomass programme area as part of the Department of Trade and Industry's New and Renewable Energy Programme. The summaries in this volume cover contractor reports on the subject published up to December 1997. (author)

  16. Sourcing Excellence

    DEFF Research Database (Denmark)

    Adeyemi, Oluseyi

    2011-01-01

    Sourcing Excellence is one of the key performance indicators (KPIs) in this world of ever changing sourcing strategies. Manufacturing companies need to access and diagnose the reliability and competencies of existing suppliers in order to coordinate and develop them. This would help in managing...

  17. Positron sources

    International Nuclear Information System (INIS)

    Chehab, R.

    1989-01-01

    A tentative survey of positron sources is given. Physical processes on which positron generation is based are indicated and analyzed. Explanation of the general features of electromagnetic interactions and nuclear β + decay makes it possible to predict the yield and emittance for a given optical matching system between the positron source and the accelerator. Some kinds of matching systems commonly used - mainly working with solenoidal fields - are studied and the acceptance volume calculated. Such knowledge is helpful in comparing different matching systems. Since for large machines, a significant distance exists between the positron source and the experimental facility, positron emittance has to be preserved during beam transfer over large distances and methods used for that purpose are indicated. Comparison of existing positron sources leads to extrapolation to sources for future linear colliders

  18. Source splitting via the point source method

    International Nuclear Information System (INIS)

    Potthast, Roland; Fazi, Filippo M; Nelson, Philip A

    2010-01-01

    We introduce a new algorithm for source identification and field splitting based on the point source method (Potthast 1998 A point-source method for inverse acoustic and electromagnetic obstacle scattering problems IMA J. Appl. Math. 61 119–40, Potthast R 1996 A fast new method to solve inverse scattering problems Inverse Problems 12 731–42). The task is to separate the sound fields u j , j = 1, ..., n of n element of N sound sources supported in different bounded domains G 1 , ..., G n in R 3 from measurements of the field on some microphone array—mathematically speaking from the knowledge of the sum of the fields u = u 1 + ... + u n on some open subset Λ of a plane. The main idea of the scheme is to calculate filter functions g 1 ,…, g n , n element of N, to construct u l for l = 1, ..., n from u| Λ in the form u l (x) = ∫ Λ g l,x (y)u(y)ds(y), l=1,... n. (1) We will provide the complete mathematical theory for the field splitting via the point source method. In particular, we describe uniqueness, solvability of the problem and convergence and stability of the algorithm. In the second part we describe the practical realization of the splitting for real data measurements carried out at the Institute for Sound and Vibration Research at Southampton, UK. A practical demonstration of the original recording and the splitting results for real data is available online

  19. Aircraft Configuration Noise Reduction. Volume 3. Computer Program Source Listing

    Science.gov (United States)

    1976-06-01

    BANOS.ABU( . C BCF = THE ARRAY OF BAND CEN\\TER FRECUENCIES. AbSOKP I b C T =AMBIENT TEMPERATURE IN’ DEGREES FARENHEIT ABSUtRP 17 C AdSOt(P 18 C OUTPUT...C 1) ARGUMENT (XI REMAINS IUCHANGEC LFI .7 C 2) NO CTHER SUbPROGRAMS REQLIRED C ER STANDARC FORTRAN IV LIbkARY. CFI 28 c 3) ABSOLUTE ERROR IS LESS...MINOR AND MAJOR INDEX CCLtNTERS CORSP. 76 14 NRN = 1 CfjRSPL 7S ICI = 1B129NCOF) CORSPL 8C IF (IGO .GT. 1) GO TO 105 CORSPL 81 C CORSPL 82 C ZERO CUT

  20. Dimension reduction and multiscaling law through source extraction

    Science.gov (United States)

    Capobianco, Enrico

    2003-04-01

    Through the empirical analysis of financial return generating processes one may find features that are common to other research fields, such as internet data from network traffic, physiological studies about human heart beat, speech and sleep recorded time series, geophysics signals, just to mention well-known cases of study. In particular, long range dependence, intermittency, heteroscedasticity are clearly appearing, and consequently power laws and multi-scaling behavior result typical signatures of either the spectral or the time correlation diagnostics. We study these features and the dynamics underlying financial volatility, which can respectively be detected and inferred from high frequency realizations of stock index returns, and show that they vary according to the resolution levels used for both the analysis and the synthesis of the available information. Discovering whether the volatility dynamics are subject to changes in scaling regimes requires the consideration of a model embedding scale-dependent information packets, thus accounting for possible heterogeneous activity occurring in financial markets. Independent component analysis result to be an important tool for reducing the dimension of the problem and calibrating greedy approximation techniques aimed to learn the structure of the underlying volatility.

  1. Breast reduction (mammoplasty) - slideshow

    Science.gov (United States)

    ... page: //medlineplus.gov/ency/presentations/100189.htm Breast reduction (mammoplasty) - series—Indications To use the sharing features ... Lickstein, MD, FACS, specializing in cosmetic and reconstructive plastic surgery, Palm Beach Gardens, FL. Review provided by ...

  2. Medical Errors Reduction Initiative

    National Research Council Canada - National Science Library

    Mutter, Michael L

    2005-01-01

    The Valley Hospital of Ridgewood, New Jersey, is proposing to extend a limited but highly successful specimen management and medication administration medical errors reduction initiative on a hospital-wide basis...

  3. Microbial reductive dehalogenation.

    OpenAIRE

    Mohn, W W; Tiedje, J M

    1992-01-01

    A wide variety of compounds can be biodegraded via reductive removal of halogen substituents. This process can degrade toxic pollutants, some of which are not known to be biodegraded by any other means. Reductive dehalogenation of aromatic compounds has been found primarily in undefined, syntrophic anaerobic communities. We discuss ecological and physiological principles which appear to be important in these communities and evaluate how widely applicable these principles are. Anaerobic commun...

  4. Air Layer Drag Reduction

    Science.gov (United States)

    Ceccio, Steven; Elbing, Brian; Winkel, Eric; Dowling, David; Perlin, Marc

    2008-11-01

    A set of experiments have been conducted at the US Navy's Large Cavitation Channel to investigate skin-friction drag reduction with the injection of air into a high Reynolds number turbulent boundary layer. Testing was performed on a 12.9 m long flat-plate test model with the surface hydraulically smooth and fully rough at downstream-distance-based Reynolds numbers to 220 million and at speeds to 20 m/s. Local skin-friction, near-wall bulk void fraction, and near-wall bubble imaging were monitored along the length of the model. The instrument suite was used to access the requirements necessary to achieve air layer drag reduction (ALDR). Injection of air over a wide range of air fluxes showed that three drag reduction regimes exist when injecting air; (1) bubble drag reduction that has poor downstream persistence, (2) a transitional regime with a steep rise in drag reduction, and (3) ALDR regime where the drag reduction plateaus at 90% ± 10% over the entire model length with large void fractions in the near-wall region. These investigations revealed several requirements for ALDR including; sufficient volumetric air fluxes that increase approximately with the square of the free-stream speed, slightly higher air fluxes are needed when the surface tension is reduced, higher air fluxes are required for rough surfaces, and the formation of ALDR is sensitive to the inlet condition.

  5. A power transformer as a source of noise.

    Science.gov (United States)

    Zawieska, Wiktor Marek

    2007-01-01

    This article presents selected results of analyses and simulations carried out as part of research performed at the Central Institute of Labor Protection - the National Research Institute (CIOP-PIB) in connection with the development of a system for active reduction of noise emitted by high power electricity transformers. This analysis covers the transformer as a source of noise as well as a mathematical description of the phenomenon of radiation of vibroacoustic energy through a transformer enclosure modeled as a vibrating rectangular plate. Also described is an acoustic model of the transformer in the form of an array of loudspeakers.

  6. Virtual Generation (Energy Efficiency) The Cheapest Source For Power Generation

    Energy Technology Data Exchange (ETDEWEB)

    Hasnie, Sohail

    2010-09-15

    Energy efficiency is the cheapest source of energy that has escaped the minds of the politicians in the developing countries. This paper argues for large scale utility led end use efficiency programs in a new paradigm, where 1 million efficient light bulbs is synonymous to a 50 MW power station that costs only 2% of the traditional fossil fuel power station and zero maintenance. Bulk procurement, setting up new standards and generation of certified emissions reduction is part of this strategy. It discusses implementation of a $20 million pilot in the Philippines supported by the Asian Development Bank.

  7. Relativistic model for statevector reduction

    International Nuclear Information System (INIS)

    Pearle, P.

    1991-04-01

    A relativistic quantum field model describing statevector reduction for fermion states is presented. The time evolution of the states is governed by a Schroedinger equation with a Hamiltonian that has a Hermitian and a non-Hermitian part. In addition to the fermions, the Hermitian part describes positive and negative energy mesons of equal mass, analogous to the longitudinal and timelike photons of electromagnetism. The meson-field-sum is coupled to the fermion field. This ''dresses'' each fermion so that, in the extreme nonrelativistic limit (non-moving fermions), a fermion in a position eigenstate is also in an eigenstate of the meson-field-difference with the Yukawa-potential as eigenvalue. However, the fermions do not interact: this is a theory of free dressed fermions. It is possible to obtain a stationary normalized ''vacuum'' state which satisfies two conditions analogous to the gauge conditions of electromagnetism (i.e., that the meson-field-difference, as well as its time derivative, give zero when applied to the vacuum state), to any desired degree of accuracy. The non-Hermitian part of the Hamiltonian contains the coupling of the meson-field-difference to an externally imposed c-number fluctuating white noise field, of the CSL (Continuous Spontaneous Localization) form. This causes statevector reduction, as is shown in the extreme nonrelativistic limit. For example, a superposition of spatially separated wavepackets of a fermion will eventually be reduced to a single wavepacket: the meson-field-difference discriminates among the Yukawa-potential ''handles'' attached to each wavepacket, thereby selecting one wavepacket to survive by the CSL mechanism. Analysis beyond that given in this paper is required to see what happens when the fermions are allowed to move. (It is possible that the ''vacuum'' state becomes involved in the dynamics so that the ''gauge'' conditions can no longer be maintained.) It is shown how to incorporate these ideas into quantum

  8. Economics of alternative energy sources

    International Nuclear Information System (INIS)

    Ryle, M.

    1977-01-01

    It is stated that an important part of the oil and natural gas at present consumed in the UK is used for the heating of buildings, a demand which shows large diurnal, day-to-day and annual fluctuations. The replacement of this energy by nuclear-generated electricity, as at present envisaged, would require the construction of some 250 GW of additional capacity by the end of the century, a programme which does not seem feasible. By incorporating relatively cheap short term storage in the form of low-grade heat, the generating capacity required to fulfil peak demand could be reduced by more than 50%. As soon as such storage is provided, however, other sources of energy should become viable and attractive alternatives, and the UK is well situated to make use of wind, wave, and tidal power. It seems likely that the value of North Sea oil/gas reserves as feedstock to the chemical industry will rise sufficiently to make an early reduction in their consumption as fuel of great economic importance. (author)

  9. Economics of alternative energy sources.

    Science.gov (United States)

    Ryle, M

    1977-05-12

    An important part of the oil and natural gas at present consumed in the UK is used for the heating of buildings, a demand which shows large diurnal, day-to-day and annual fluctuations. The replacement of this energy by nuclear-generated electricity, as at present envisaged, would require the construction of some 250 GW of additional capacity by the end of the century, a progamme which does not seem feasible. By incorporating relatively cheap, short term storage in the form of low-grade heat, the generating capacity required to fulfil peak demand could be reduced by more than 50%. As soon as such storage is provided, however, other sources of energy become viable and attractive alternatives, and the UK is well situated to make use of wind, wave, and tidal power. It seems likely that the value of North Sea oil/gas reserves as feedstock to the chemical industry will rise sufficiently to make an early reduction in their consumption as fuel of great economic importance.

  10. F4U production by electrolytic reduction

    International Nuclear Information System (INIS)

    Esteban Duque, A.; Gispert Benach, M.; Hernandez Arroyo, F.; Montes Ponce de Leon, M.; Rojas de Diego, J. L.

    1974-01-01

    As a part of the nuclear fuel cycle program developed at the Spanish Atomic Energy Commission it has been studied the electrolytic reduction of U-VI to U-IV. The effect of the materials, electrolyte concentration, pH, current density, cell size and laboratory scale production is studied. The Pilot Plant and the production data are also described. (Author) 18 refs

  11. Sulfate reduction and methanogenesis at a freshwater

    DEFF Research Database (Denmark)

    Iversen, Vibeke Margrethe Nyvang; Andersen, Martin Søgaard; Jakobsen, Rasmus

    The freshwater-seawater interface was studied in a ~9-m thick anaerobic aquifer located in marine sand and gravel with thin peat lenses. Very limited amounts of iron-oxides are present. Consequently, the dominating redox processes are sulfate reduction and methanogenesis, and the groundwater...... is enriched in dissolved sulfide, methane and bicarbonate. Under normal conditions the seawater-freshwater interface is found at a depth of 4 m at the coastline and reaches the bottom of the aquifer 40 m inland. However, occasional flooding of the area occurs, introducing sulfate to the aquifer. Groundwater...... chemistry was studied in a 120 m transect perpendicular to the coast. Cores were taken for radiotracer rate measurements of sulfate reduction and methanogenesis. In the saline part of the aquifer 35 m inland, sulfate reduction was the dominant process with rates of 0.1-10 mM/year. In the freshwater part 100...

  12. Optimization of dynamic source depth for seismic surveys. Part 7; Dynamite shingen no hasshin shindo no saitekika ni tsuite (hyoso kozo no suitei (kusssetsuho jishin tansa oyobi denki denjiho tansa)). 7

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, H; Murayama, R; Mitsuhata, Y; Ishikawa, H [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1996-05-01

    For the improvement of quality of data collected by reflection aided seismic exploration using dynamite as the seismic source, information has to be collected about the surface layer structure before the charge depth is determined. For this purpose, refraction, electric, and electromagnetic exploration methods were tried. In the refraction method, an impactor was used as the seismic source. In the records, the surface wave prevails because vibration was generated on the surface. Analysis was made by the use of the initial travel time tomography. In the electric exploration, a double pole array was used to measure resistivity. The measured data was subjected to a fully automatic inversion for analysis. As the result, it was disclosed that it was useful to know the deep-level structure directly by use of tomographic methods in refraction seismic exploration so as to find the optimum charge level. Furthermore, about the electric and electromagnetic exploration techniques, it was found that these methods can be applied making use of resistivity to the evaluation of groundwater saturation. 7 refs., 5 figs., 3 tabs.

  13. Agreements concluded by the Federal Republic of Germany under international law in the field of environmental protection. Annex: Treaties with the GDR. (Source index in the Federal Law Gazette, part II). (As of September 15, 1987)

    International Nuclear Information System (INIS)

    Lohse, S.

    1987-01-01

    This compilation contains all agreements under international law in the field of environmental protection, the FRG has joined and that have been published and/or announced in the Federal Law Gazette, part II. The summary is of September 15, 1987. The classification is made according to the subjects: waste management law, pollution abatement law, nuclear law and energy and mining law and within these according to the date of treaty/agreement. For easier access, there are a chronological index, an index of the contracting states and an index of the places of contract. In the annex the relevant treaties with the German Democratic Republic are indicated. (orig./HP) [de

  14. 10 years and 20,000 sources: the offsite source recovery project

    Energy Technology Data Exchange (ETDEWEB)

    Whitworth, Julia R [Los Alamos National Laboratory; Abeyta, Cristy L [Los Alamos National Laboratory; Pearson, Michael W [Los Alamos National Laboratory

    2009-01-01

    The Global Threat Reduction Initiative's (GTRI) Offsite Source Recovery Project (OSRP) has been recovering excess and unwanted sealed sources for ten years. In January 2009, GTRI announced that the project had recovered 20,000 sealed radioactive sources. This project grew out of early efforts at Los Alamos National Laboratory (LANL) to recover and disposition excess Plutonium-239 (Pu-239) sealed sources that were distributed in the 1960s and 1970s under the Atoms for Peace Program. Sealed source recovery was initially considered a waste management activity, as evidenced by its initial organization under the Department of Energy's (DOE's) Environmental Management (EM) program. After the terrorist attacks of 2001, however, the interagency community began to recognize the threat posed by excess and unwanted radiological material, particularly those that could not be disposed at the end of their useful life. After being transferred to the National Nuclear Security Administration (NNSA) to be part of GTRI, OSRP's mission was expanded to include not only material that would be classified as Greater-than-Class-C (GTCC) when it became waste, but also any other materials that might be a 'national security consideration.' This paper discusses OSRP's history, recovery operations, expansion to accept high-activity beta-gamma-emitting sealed sources and devices and foreign-possessed sources, and more recent efforts such as cooperative projects with the Council on Radiation Control Program Directors (CRCPD) and involvement in GTRI's Search and Secure project. Current challenges and future work will also be discussed.

  15. The Global Earthquake Model and Disaster Risk Reduction

    Science.gov (United States)

    Smolka, A. J.

    2015-12-01

    Advanced, reliable and transparent tools and data to assess earthquake risk are inaccessible to most, especially in less developed regions of the world while few, if any, globally accepted standards currently allow a meaningful comparison of risk between places. The Global Earthquake Model (GEM) is a collaborative effort that aims to provide models, datasets and state-of-the-art tools for transparent assessment of earthquake hazard and risk. As part of this goal, GEM and its global network of collaborators have developed the OpenQuake engine (an open-source software for hazard and risk calculations), the OpenQuake platform (a web-based portal making GEM's resources and datasets freely available to all potential users), and a suite of tools to support modelers and other experts in the development of hazard, exposure and vulnerability models. These resources are being used extensively across the world in hazard and risk assessment, from individual practitioners to local and national institutions, and in regional projects to inform disaster risk reduction. Practical examples for how GEM is bridging the gap between science and disaster risk reduction are: - Several countries including Switzerland, Turkey, Italy, Ecuador, Papua-New Guinea and Taiwan (with more to follow) are computing national seismic hazard using the OpenQuake-engine. In some cases these results are used for the definition of actions in building codes. - Technical support, tools and data for the development of hazard, exposure, vulnerability and risk models for regional projects in South America and Sub-Saharan Africa. - Going beyond physical risk, GEM's scorecard approach evaluates local resilience by bringing together neighborhood/community leaders and the risk reduction community as a basis for designing risk reduction programs at various levels of geography. Actual case studies are Lalitpur in the Kathmandu Valley in Nepal and Quito/Ecuador. In agreement with GEM's collaborative approach, all

  16. Effects of the source of energy and minerals on microbial protein synthesis in rumen using 35S as indicator. Part of a coordinated programme on tracer techniques in studies on the use of non-protein nitrogen in ruminants

    International Nuclear Information System (INIS)

    Durant, M.

    1976-05-01

    Part I. The effect of the nature of carbohydrates and minerals on microbial growth in vitro was studied in vitro to intensify rumen microbial protein synthesis from non-protein nitrogen, using phosphorus incorporation (PR). The nature of starch greatly influences urea utilization. Among the tropical tubers studied, yam Cayenesis and canna Edulis give lower urea utilization than cassava and yam Dumetorum. However, this can be improved by processing. The effects are greatest when the proportion of urea to processed cereal is ca. 4-5%. S-addition as sulfate improves urea utilization with both natural and purified diets. Part II. Results from the Jouy and Ghent laboratories were analyzed statistically, to check the accuracy of the 32 P method for estimating microbial growth, using protein-free substrates. The linear relationship between PR and every other variable was studied. Two multivariate analyses, principal components and multiple regression, were applied. Net NH 3 utilization was predicted using the equations for substrates with proteins likely to be degraded. This method appears more accurate than using the N/P ratio in microflora. Equations should only be used under the specific experiments described

  17. Ion sources for electrostatic accelerators

    International Nuclear Information System (INIS)

    Hellborg, R.

    1998-01-01

    Maybe the most important part of an electrostatic accelerator system, and also often the most tricky part is the ion source. There has been a rapid growth in activity in ion-source research and development during the last two to three decades. Some of these developments have also been of benefit to electrostatic accelerator users. In this report some of the different types of ion sources used in electrostatic accelerators are described. The list is not complete but more an overview of some of the more commonly used sources. The description is divided into two groups; positive ion sources for single stage electrostatic accelerators and negative ion sources for two stages (i.e. tandem) accelerators

  18. Modeling dry and wet deposition of sulfate, nitrate, and ammonium ions in Jiuzhaigou National Nature Reserve, China using a source-oriented CMAQ model: Part I. Base case model results.

    Science.gov (United States)

    Qiao, Xue; Tang, Ya; Hu, Jianlin; Zhang, Shuai; Li, Jingyi; Kota, Sri Harsha; Wu, Li; Gao, Huilin; Zhang, Hongliang; Ying, Qi

    2015-11-01

    A source-oriented Community Multiscale Air Quality (CMAQ) model driven by the meteorological fields generated by the Weather Research and Forecasting (WRF) model was used to study the dry and wet deposition of nitrate (NO3(-)), sulfate (SO4(2-)), and ammonium (NH4(+)) ions in the Jiuzhaigou National Nature Reserve (JNNR), China from June to August 2010 and to identify the contributions of different emission sectors and source regions that were responsible for the deposition fluxes. The model performance is evaluated in this paper and the source contribution analyses are presented in a companion paper. The results show that WRF is capable of reproducing the observed precipitation rates with a Mean Normalized Gross Error (MNGE) of 8.1%. Predicted wet deposition fluxes of SO4(2-) and NO3(-) at the Long Lake (LL) site (3100 m a.s.l.) during the three-month episode are 2.75 and 0.34 kg S(N) ha(-1), which agree well with the observed wet deposition fluxes of 2.42 and 0.39 kg S(N) ha(-1), respectively. Temporal variations in the weekly deposition fluxes at LL are also well predicted. Wet deposition flux of NH4(+) at LL is over-predicted by approximately a factor of 3 (1.60 kg N ha(-1)vs. 0.56 kg N ha(-1)), likely due to missing alkaline earth cations such as Ca(2+) in the current CMAQ simulations. Predicted wet deposition fluxes are also in general agreement with observations at four Acid Deposition Monitoring Network in East Asia (EANET) sites in western China. Predicted dry deposition fluxes of SO4(2-) (including gas deposition of SO2) and NO3(-) (including gas deposition of HNO3) are 0.12 and 0.12 kg S(N) h a(-1) at LL and 0.07 and 0.08 kg S(N) ha(-1) at Jiuzhaigou Bureau (JB) in JNNR, respectively, which are much lower than the corresponding wet deposition fluxes. Dry deposition flux of NH4(+) (including gas deposition of NH3) is 0.21 kg N ha(-1) at LL, and is also much lower than the predicted wet deposition flux. For both dry and wet deposition fluxes, predictions

  19. Harm reduction-the cannabis paradox

    Directory of Open Access Journals (Sweden)

    Melamede Robert

    2005-09-01

    Full Text Available Abstract This article examines harm reduction from a novel perspective. Its central thesis is that harm reduction is not only a social concept, but also a biological one. More specifically, evolution does not make moral distinctions in the selection process, but utilizes a cannabis-based approach to harm reduction in order to promote survival of the fittest. Evidence will be provided from peer-reviewed scientific literature that supports the hypothesis that humans, and all animals, make and use internally produced cannabis-like products (endocannabinoids as part of the evolutionary harm reduction program. More specifically, endocannabinoids homeostatically regulate all body systems (cardiovascular, digestive, endocrine, excretory, immune, nervous, musculo-skeletal, reproductive. Therefore, the health of each individual is dependant on this system working appropriately.

  20. Quantum theory without reduction

    International Nuclear Information System (INIS)

    Cini, Marcello; Levy-Leblond, J.-M.

    1990-01-01

    Quantum theory offers a strange, and perhaps unique, case in the history of science. Although research into its roots has provided important results in recent years, the debate goes on. Some theorists argue that quantum theory is weakened by the inclusion of the so called 'reduction of the state vector' in its foundations. Quantum Theory without Reduction presents arguments in favour of quantum theory as a consistent and complete theory without this reduction, and which is capable of explaining all known features of the measurement problem. This collection of invited contributions defines and explores different aspects of this issue, bringing an old debate into a new perspective, and leading to a more satisfying consensus about quantum theory. (author)

  1. Measuring mandibular ridge reduction

    International Nuclear Information System (INIS)

    Steen, W.H.A.

    1984-01-01

    This thesis investigates the mandibular reduction in height of complete denture wearers and overdenture wearers. To follow this reduction in the anterior region as well as in the lateral sections of the mandible, an accurate and reproducible measuring method is a prerequisite. A radiologic technique offers the best chance. A survey is given of the literature concerning the resorption process after the extraction of teeth. An oblique cephalometric radiographic technique is introduced as a promising method to measure mandibular ridge reduction. The reproducibility and the accuracy of the technique are determined. The reproducibility in the positioning of the mandible is improved by the introduction of a mandibular support which permits a precise repositioning of the edentulous jaw, even after long periods of investigation. (Auth.)

  2. Crowd Sourcing.

    Science.gov (United States)

    Baum, Neil

    2016-01-01

    The Internet has contributed new words and slang to our daily vernacular. A few terms, such as tweeting, texting, sexting, blogging, and googling, have become common in most vocabularies and in many languages, and are now included in the dictionary. A new buzzword making the rounds in industry is crowd sourcing, which involves outsourcing an activity, task, or problem by sending it to people or groups outside a business or a practice. Crowd sourcing allows doctors and practices to tap the wisdom of many instead of relying only on the few members of their close-knit group. This article defines "crowd sourcing," offers examples, and explains how to get started with this approach that can increase your ability to finish a task or solve problems that you don't have the time or expertise to accomplish.

  3. HCMM imagery for the discrimination of rock types, the detection of geothermal energy sources and the assessment of soil moisture content in western Queensland and adjacent parts of New South Wales and South Australia

    Science.gov (United States)

    Cole, M. M. (Principal Investigator)

    1980-01-01

    The author has identified the following significant results. Day-visible and day-IR imagery of northwest Queensland show that large scale geological features like the Mitakoodi anticlinorium, which involves rocks of contrasting lithological type, can be delineated. North of Cloncurry, the contrasting lithological units of the Knapdale quartzite and bedded argillaceous limestones within the Proterozoic Corella sequence are clearly delineated in the area of the Dugald River Lode. Major structural features in the Mount Isa area are revealed on the day-visible cover. Which provides similar but less detailed information than the LANDSAT imagery. The day-IR cover provides less additional information for areas of outcropping bedrock than had been expected. Initial studies of the day-IR and night-IR cover for parts of South Australia suggest that they contain additional information on geology compared with day-visible cover.

  4. Arsenic and drinking water. Part 1. A review of the source, distribution and behaviour of arsenic in the environment; Arsen und Trinkwasser. Teil 1. Ein Ueberblick ueber Vorkommen, Verteilung und Verhalten von Arsen in der Umwelt

    Energy Technology Data Exchange (ETDEWEB)

    Oberacker, F.; Maier, D. [Heinrich-Sontheimer-Lab., DVGW-Technologiezentrum Wasser, Karlsruhe (Germany); Maier, M. [Stadtwerke Karlsruhe GmbH, Karlsruhe (Germany)

    2002-11-01

    Arsenic is ubiquituously distributed in our environment and is subject to continuous bio-geochemical cycling. Besides the acute toxicity of arsenic its chronic effects are of special importance. The permanent uptake with drinking water for example might cause cancer. Today, arsenic compounds hardly serve as pesticides anymore, although chromated copper arsenate is still used to preserve wood. Furthermore, arsenic is used in the alloy, glass and semiconductor industry. The main part of the earths' arsenic resources are bound to sulfur in the lithosphere. By means of rock weathering and volcanism it is transferred into pedo-, hydro- and atmosphere, where it is mainly bound to oxygen. Microorganisms are able to methylate the arsenic, whereby gaseous arsenic compounds are carried into the atmosphere. Also, it is released from the lithosphere through anthropogenic mining activities, although only for a small part of the released amount useful applications exist. The arsenic behaviour in natural waters is closely related to sulfur on the one hand and to iron oxides on the other. Under strongly reducing conditions the arsenic is precipitated as sulfide, while under oxidising conditions it is adsorbed to the surfaces of iron oxides. Therefore, under aerobic conditions the arsenic concentrations of aqueous solutions are controlled by these adsorption processes rather than by the solubility of solid arsenic phases. Manganese oxides also play an important role as they are able to rapidly oxidise As(III) to As(V). These processes of release and fixation of arsenic in the nature must be studied carefully, because they are applied for arsenic elimination during drinking water production as well. (orig.)

  5. NF ISO 7097-1. Nuclear fuel technology - Uranium dosimetry in solutions, in uranium hexafluoride and in solids - Part 1: reduction with iron (II) / oxidation with potassium bi-chromate / titration method; NF ISO 7097-1. Technologie du combustible nucleaire. Dosage de l'uranium dans des solutions, l'hexafluorure d'uranium et des solides. Partie 1: reduction par fer (II) / oxydation par bichromate de potassium / methode par titrage

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-04-01

    This standard document describes the mode of operation of three different methods for the quantitative dosimetry of uranium in solutions, in UF{sub 6} and in solids: reduction by iron (II), oxidation by potassium bi-chromate and titration. (J.S.)

  6. Energy sources

    International Nuclear Information System (INIS)

    Vajda, Gy.

    1998-01-01

    A comprehensive review is presented of the available sources of energy in the world is presented. About 80 percent of primary energy utilization is based on fossile fuels, and their dominant role is not expected to change in the foreseeable future. Data are given on petroleum, natural gas and coal based power production. The role and economic aspects of nuclear power are analyzed. A brief summary of renewable energy sources is presented. The future prospects of the world's energy resources are discussed, and the special position of Hungary regarding fossil, nuclear and renewable energy and the country's energy potential is evaluated. (R.P.)

  7. REDUCTIONS WITHOUT REGRET: SUMMARY

    Energy Technology Data Exchange (ETDEWEB)

    Swegle, J.; Tincher, D.

    2013-09-16

    This paper briefly summarizes the series in which we consider the possibilities for losing, or compromising, key capabilities of the U.S. nuclear force in the face of modernization and reductions. The first of the three papers takes an historical perspective, considering capabilities that were eliminated in past force reductions. The second paper is our attempt to define the needed capabilities looking forward in the context of the current framework for force modernization and the current picture of the evolving challenges of deterrence and assurance. The third paper then provides an example for each of our undesirable outcomes: the creation of roach motels, box canyons, and wrong turns.

  8. Advanced modern algebra part 2

    CERN Document Server

    Rotman, Joseph J

    2017-01-01

    This book is the second part of the new edition of Advanced Modern Algebra (the first part published as Graduate Studies in Mathematics, Volume 165). Compared to the previous edition, the material has been significantly reorganized and many sections have been rewritten. The book presents many topics mentioned in the first part in greater depth and in more detail. The five chapters of the book are devoted to group theory, representation theory, homological algebra, categories, and commutative algebra, respectively. The book can be used as a text for a second abstract algebra graduate course, as a source of additional material to a first abstract algebra graduate course, or for self-study.

  9. Filtered cathodic arc source

    International Nuclear Information System (INIS)

    Falabella, S.; Sanders, D.M.

    1994-01-01

    A continuous, cathodic arc ion source coupled to a macro-particle filter capable of separation or elimination of macro-particles from the ion flux produced by cathodic arc discharge is described. The ion source employs an axial magnetic field on a cathode (target) having tapered sides to confine the arc, thereby providing high target material utilization. A bent magnetic field is used to guide the metal ions from the target to the part to be coated. The macro-particle filter consists of two straight solenoids, end to end, but placed at 45 degree to one another, which prevents line-of-sight from the arc spot on the target to the parts to be coated, yet provides a path for ions and electrons to flow, and includes a series of baffles for trapping the macro-particles. 3 figures

  10. Fouzth report to Congress: resource recovery and waste reduction

    Energy Technology Data Exchange (ETDEWEB)

    1977-01-01

    The report covers domestic refuse generation and resource recovery estimates. A discussion of waste reduction at various national organizational levels, source separation, mixed refuse processing for energy production, and environmental and economic impact of beverage containers deposit law are included.

  11. Careers Education: An Effective Tool for Poverty Reduction | Okafor ...

    African Journals Online (AJOL)

    Careers Education: An Effective Tool for Poverty Reduction. ... Open Access DOWNLOAD FULL TEXT Subscription or Fee Access ... The research was carried out based mainly on the secondary source of data. Among other things, the study ...

  12. Open Source Software Development

    Science.gov (United States)

    2011-01-01

    appropriate to refer to FOSS or FLOSS (L for Libre , where the alternative term “ libre software ” has popularity in some parts of the world) in order...Applying Social Network Analysis to Community-Drive Libre Software Projects, Intern. J. Info. Tech. and Web Engineering, 2006, 1(3), 27-28. 17...Open Source Software Development* Walt Scacchi Institute for Software Researcher University of California, Irvine Irvine, CA 92697-3455 USA Abstract

  13. Ion source

    International Nuclear Information System (INIS)

    1977-01-01

    The specifications of a set of point-shape electrodes of non-corrodable material that can hold a film of liquid material of equal thickness is described. Contained in a jacket, this set forms an ion source. The electrode is made of tungsten with a glassy carbon layer for insulation and an outer layer of aluminium-oxide ceramic material

  14. Field Demonstration of Ground-Source Integrated Heat Pump Part I. Technology and Field Demo System/Site Descriptions, and Preliminary Summer/Fall Performance Analysis for One Site

    Energy Technology Data Exchange (ETDEWEB)

    Baxter, Van D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Munk, Jeffrey D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gehl, Anthony C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2016-02-01

    The field study is planned to continue through the 2016 cooling season with the draft final project report due by September 30, 2016. This report provides a description of both installations and preliminary 2015 cooling and fall season performance results for the Knoxville site. For the August 18 through December 14 period, the Knoxville site GS-IHP provided 53.6% total source energy savings compared to a baseline electric RTU/heat pump and electric WH. Peak demand savings ranged from 33% to 59% per month. Energy cost savings of 53.1% have been achieved to date with more than half of that coming from reduced demand charges. Data on installation and maintenance costs are being collected and will be combined with total test period energy savings data for a payback analysis to be included in the project final report. The GS-IHP also saved a significant amount of carbon emissions. The total emission savings for the Knoxville site for the August-December 2015 period were ~0.8 metric tons. If trading for carbon credits ever becomes a reality, additional cost savings would be realized.

  15. Development of radiation curable surface coating based on soybean oil. part II: Evaluation of the prepared acrylated resin as surface coatings by using EB or UV sources for radiation curing applications

    International Nuclear Information System (INIS)

    Ibrahim, M.S.; Said, H.M.; Moussa, I.M.

    2005-01-01

    In recent years, there has been a growing trend in using vegetable oils as raw materials in acylation production that can be cured by UV/EB systems. The acrylated resin formulates by using individually different functional acrylate monomers were prepared and cured by EB or UV sources. The characterization properties of the cured films were investigated in terms of pendulum hardness, bending, impact, gloss, adhesion and chemical tests. Other formulations were prepared by mixing a constant ratio of different functional acrylate monomers and exposed to UV or EB irradiation. The results showed that the hardness of cured films were increased by increasing the functionality of monomers with excellent adhesion for all formulations but at expense of other properties involving bending and impact tests. Therefore, it can be deduce that the hardness of the curing surface coating by using EB was found to be nearly twice the hardness of the curing surface coating by using UV irradiation. Also, the best formulations which have given good chemical and mechanical properties are (mono-di) functional acrylate monomer resin under EB and (mono-tri) functional acrylate monomer resin under UV irradiation

  16. Reduction of robot base parameters

    Energy Technology Data Exchange (ETDEWEB)

    Vandanjon, P O [CEA Centre d` Etudes de Saclay, 91 - Gif-sur-Yvette (France). Dept. des Procedes et Systemes Avances; Gautier, M [Nantes Univ., 44 (France)

    1996-12-31

    This paper is a new step in the search of minimum dynamic parameters of robots. In spite of planing exciting trajectories and using base parameters, some parameters remain not identifiable due to the perturbation effects. In this paper, we propose methods to reduce the set of base parameters in order to get an essential set of parameters. This new set defines a simplified identification model witch improves the noise immunity of the estimation process. It contributes also in reducing the computation burden of a simplified dynamic model. Different methods are proposed and are classified in two parts: methods, witch perform reduction and identification together, come from statistical field and methods, witch reduces the model before the identification thanks to a priori information, come from numerical field like the QR factorization. Statistical tools and QR reduction are shown to be efficient and adapted to determine the essential parameters. They can be applied to open-loop, or graph structured rigid robot, as well as flexible-link robot. Application for the PUMA 560 robot is given. (authors). 9 refs., 4 tabs.

  17. Reduction of robot base parameters

    International Nuclear Information System (INIS)

    Vandanjon, P.O.

    1995-01-01

    This paper is a new step in the search of minimum dynamic parameters of robots. In spite of planing exciting trajectories and using base parameters, some parameters remain not identifiable due to the perturbation effects. In this paper, we propose methods to reduce the set of base parameters in order to get an essential set of parameters. This new set defines a simplified identification model witch improves the noise immunity of the estimation process. It contributes also in reducing the computation burden of a simplified dynamic model. Different methods are proposed and are classified in two parts: methods, witch perform reduction and identification together, come from statistical field and methods, witch reduces the model before the identification thanks to a priori information, come from numerical field like the QR factorization. Statistical tools and QR reduction are shown to be efficient and adapted to determine the essential parameters. They can be applied to open-loop, or graph structured rigid robot, as well as flexible-link robot. Application for the PUMA 560 robot is given. (authors). 9 refs., 4 tabs

  18. LDRD report nonlinear model reduction

    Energy Technology Data Exchange (ETDEWEB)

    Segalman, D.; Heinstein, M.

    1997-09-01

    The very general problem of model reduction of nonlinear systems was made tractable by focusing on the very large subclass consisting of linear subsystems connected by nonlinear interfaces. Such problems constitute a large part of the nonlinear structural problems encountered in addressing the Sandia missions. A synthesis approach to this class of problems was developed consisting of: detailed modeling of the interface mechanics; collapsing the interface simulation results into simple nonlinear interface models; constructing system models by assembling model approximations of the linear subsystems and the nonlinear interface models. These system models, though nonlinear, would have very few degrees of freedom. A paradigm problem, that of machine tool vibration, was selected for application of the reduction approach outlined above. Research results achieved along the way as well as the overall modeling of a specific machine tool have been very encouraging. In order to confirm the interface models resulting from simulation, it was necessary to develop techniques to deduce interface mechanics from experimental data collected from the overall nonlinear structure. A program to develop such techniques was also pursued with good success.

  19. Reduction of dinitrogen ligands

    International Nuclear Information System (INIS)

    Richards, R.L.

    1983-01-01

    Processes of dinitrogen ligand reduction in complexes of transition metals are considered. The basic character of the dinitrogen ligand is underlined. Data on X-ray photoelectronic spectroscopy and intensities of bands ν (N 2 ) in IR-spectra of nitrogen complexes are given. The mechanism of protonation of an edge dinitrogen ligand is discussed. Model systems and mechanism of nitrogenogenase are compared

  20. Infinitary Combinatory Reduction Systems

    DEFF Research Database (Denmark)

    Ketema, Jeroen; Simonsen, Jakob Grue

    2011-01-01

    We define infinitary Combinatory Reduction Systems (iCRSs), thus providing the first notion of infinitary higher-order rewriting. The systems defined are sufficiently general that ordinary infinitary term rewriting and infinitary ¿-calculus are special cases. Furthermore,we generalise a number...

  1. Galactorrhea after reduction mammaplasty

    NARCIS (Netherlands)

    Schuurman, A. H.; Assies, J.; van der Horst, C. M.; Bos, K. E.

    1993-01-01

    A case of extremely painful swelling of the breasts following a reduction mammaplasty is presented. There were no signs of an abscess or hematoma. A milky white fluid due to galactorrhea was evacuated at operation, and further galactorrhea was inhibited by medication. The pathogenesis of

  2. (MTT) dye reduction assay.

    African Journals Online (AJOL)

    to inhibit proliferation of HeLa cells was determined using the 3443- dimethylthiazol-2-yl)-2,5-diphenyl-tetrazolium bromide (MTT) dye reduction assay. Extracts from roots of Agathisanthemum bojeri, Synaptolepis kirkii and Zanha africana and the leaf extract of Physalis peruviana at a concentration of 10 pg/ml inhibited cell ...

  3. Streaming Reduction Circuit

    NARCIS (Netherlands)

    Gerards, Marco Egbertus Theodorus; Kuper, Jan; Kokkeler, Andre B.J.; Molenkamp, Egbert

    2009-01-01

    Reduction circuits are used to reduce rows of floating point values to single values. Binary floating point operators often have deep pipelines, which may cause hazards when many consecutive rows have to be reduced. We present an algorithm by which any number of consecutive rows of arbitrary lengths

  4. Educating to Forgive as an Expression of Concern for Order in a Person's Natural Environment. Part. 1: Evil and Harm in the Life of a Human Person and the Source of the Need to Forgive

    Directory of Open Access Journals (Sweden)

    Michał Wyrostkiewicz

    2017-06-01

    Full Text Available The paper defines philosophical categories of good and evil in the process of upbringing and development of the personality. People are good by nature. That is why they tend towards the good, they desire what is good, they feel bad and do not function well when they are touched by evil. Goodness is part of the natural environment of the human being; goodness is the natural climate of the human person. At the same time, however, people perform bad deeds. They create evil. They often harm others. This is the cause of disorder in a person's environment. It turns out that the only effective and reasonable means of restoring such order is forgiveness. It is the only thing that has a chance to realistically stop the potential avalanche of evil that appears to be the obvious result of wrongdoing and “nurturing” harm or planning revenge. The evil that “insidiously” enters the world creates the need for forgiveness as the only way to respond to harm; as a way that leads to real order in a person's environment.

  5. The effect of sodium hydroxide on drag reduction using banana peel as a drag reduction agent

    Science.gov (United States)

    Kaur, H.; Jaafar, A.

    2018-02-01

    Drag reduction is observed as reduced frictional pressure losses under turbulent flow conditions. Drag reduction agent such as polymers can be introduced to increase the flowrate of water flowing and reduce the water accumulation in the system. Currently used polymers are synthetic polymers, which will harm our environment in excessive use of accumulation. A more environmentally-friendly drag reduction agent such as the polymer derived from natural sources or biopolymer, is then required for such purpose. As opposed to the synthetic polymers, the potential of biopolymers as drag reduction agents, especially those derived from a local plant source are not extensively explored. The drag reduction of a polymer produced from a local plant source within the turbulent regime was explored and assessed in this study using a rheometer, where a reduced a torque produced was perceived as a reduction of drag. This method proposed is less time consuming and is more practical which is producing carboxymethylcellulose from the banana peel. The cellulose powder was converted to carboxymethylcellulose (CMC) by etherification process. The carboxymethylation reaction during the synthesizing process was then optimized against the reaction temperature, reaction time and solubility. The biopolymers were then rheologically characterized, where the viscoelastic effects and the normal stresses produced by these biopolymers were utilized to further relate and explain the drag reduction phenomena. The research was structured to focus on producing the biopolymer and to assess the drag reduction ability of the biopolymer produced. The rheological behavior of the biopolymers was then analyzed based on the ability of reducing drag. The results are intended to expand the currently extremely limited experimental database. Based on the results, the biopolymer works as a good DRA.

  6. Dual source CT imaging

    International Nuclear Information System (INIS)

    Seidensticker, Peter R.; Hofmann, Lars K.

    2008-01-01

    The introduction of Dual Source Computed Tomography (DSCT) in 2005 was an evolutionary leap in the field of CT imaging. Two x-ray sources operated simultaneously enable heart-rate independent temporal resolution and routine spiral dual energy imaging. The precise delivery of contrast media is a critical part of the contrast-enhanced CT procedure. This book provides an introduction to DSCT technology and to the basics of contrast media administration followed by 25 in-depth clinical scan and contrast media injection protocols. All were developed in consensus by selected physicians on the Dual Source CT Expert Panel. Each protocol is complemented by individual considerations, tricks and pitfalls, and by clinical examples from several of the world's best radiologists and cardiologists. This extensive CME-accredited manual is intended to help readers to achieve consistently high image quality, optimal patient care, and a solid starting point for the development of their own unique protocols. (orig.)

  7. PS proton source

    CERN Multimedia

    1959-01-01

    The first proton source used at CERN's Proton Synchrotron (PS) which started operation in 1959. This is CERN's oldest accelerator still functioning today (2018). It is part of the accelerator chain that supplies proton beams to the Large Hadron Collider. The source is a Thonemann type. In order to extract and accelerate the protons at high energy, a high frequency electrical field is used (140Mhz). The field is transmitted by a coil around a discharge tube in order to maintain the gas hydrogen in an ionised state. An electrical field pulse, in the order of 15kV, is then applied via an impulse transformer between anode and cathode of the discharge tube. The electrons and protons of the plasma formed in the ionised gas in the tube, are then separated. Currents in the order of 200mA during 100 microseconds have benn obtained with this type of source.

  8. AGENDA 21 - the basic conceptual document - Agenda of the 21 century which was accepted on the United Nations Conference on Environment and Development (UNCED) in Rio de Janeiro in 1992. Part II. Source conservation and budget with their for the development

    International Nuclear Information System (INIS)

    1996-01-01

    This part of the AGENDA 21 contains 14 chapters: Air protection; The integrate approach to planning and budget with sources of the country; The fight against deforestation; The ministration about instable ecosystems: the fight with desertification and with drought; The ministration about instable ecosystems: sustainable development in mountain-ranges; The support of the sustainable development of the agriculture and the country; Preservation of the biodiversity; Environmentally suitable use of the bio-technologies; The ocean preservation, all types of seas, including closed and partially closed, and coastal areas and preservation, rationally use and development of the live sources from their; Preservation of quality and stocks of the fresh-water sources: applying of integral access at the development, budget and use of the water sources; Environmentally sustainable treatment with toxic chemical substances including block off non-legal international transport of the toxic and dangerous products; Environmentally sustainable treatment with toxic chemical substances including block off non-legal international transport of the toxic and dangerous wastes; Environmentally sustainable treatment with solid wastes and sludges; (22) Safe and environmentally sustainable treatment with radioactive wastes

  9. Atmospheric discharge and dispersion of radionuclides during the Fukushima Dai-ichi Nuclear Power Plant accident. Part I: Source term estimation and local-scale atmospheric dispersion in early phase of the accident

    International Nuclear Information System (INIS)

    Katata, Genki; Ota, Masakazu; Terada, Hiroaki; Chino, Masamichi; Nagai, Haruyasu

    2012-01-01

    The atmospheric release of 131 I and 137 Cs in the early phase of the Fukushima Dai-ichi Nuclear Power Plant (FNPP1) accident from March 12 to 14, 2011 was estimated by combining environmental data with atmospheric dispersion simulations under the assumption of a unit release rate (1 Bq h −1 ). For the simulation, WSPEEDI-II computer-based nuclear emergency response system was used. Major releases of 131 I (>10 15 Bq h −1 ) were estimated when air dose rates increased in FNPP1 during the afternoon on March 12 after the hydrogen explosion of Unit 1 and late at night on March 14. The high-concentration plumes discharged during these periods flowed to the northwest and south–southwest directions of FNPP1, respectively. These plumes caused a large amount of dry deposition on the ground surface along their routes. Overall, the spatial pattern of 137 Cs and the increases in the air dose rates observed at the monitoring posts around FNPP1 were reproduced by WSPEEDI-II using estimated release rates. The simulation indicated that air dose rates significantly increased in the south–southwest region of FNPP1 by dry deposition of the high-concentration plume discharged from the night of March 14 to the morning of March 15. - Highlights: ► Source term during the Fukushima Dai-ichi Nuclear Power Plant accident was estimated. ► Atmospheric dispersion simulation was carried out for estimation. ► Major releases were estimated in the afternoon on March 12 and the night on March 14. ► Air dose rate increased due to dry deposition during the night of March 14.

  10. Establishing credible emission reduction estimates: GERT's experience

    International Nuclear Information System (INIS)

    Loseth, H.

    2001-01-01

    To address the challenge of reducing the greenhouse gas emissions in Canada, the federal and provincial governments are developing strategies and policies to reach that goal. One of the proposed solutions is the establishment of an emission trading system, which it is believed would encourage investment in lower-cost reductions. The Greenhouse Gas Emission Reduction Trading (GERT) pilot was established in 1998 to examine emission trading. It represents the collaborative efforts of government, industry, and non-governmental organizations. It is possible to establish emission reduction trading outside of a regulated environment. Emission reduction is defined as being an action which reduces emissions when compared to what they would have been otherwise. The functioning of GERT was described from the initial application by a buyer/seller to the review process. The assessment of projects is based on mandatory criteria: reductions of emissions must be real, measurable, verifiable and surplus. A section of the presentation was devoted to landfill gas recovery project issues, while another dealt with fuel substitution project issues. Section 5 discussed emission reductions from an off-site source electricity project issues. figs

  11. Advanced digital signal processing and noise reduction

    CERN Document Server

    Vaseghi, Saeed V

    2008-01-01

    Digital signal processing plays a central role in the development of modern communication and information processing systems. The theory and application of signal processing is concerned with the identification, modelling and utilisation of patterns and structures in a signal process. The observation signals are often distorted, incomplete and noisy and therefore noise reduction, the removal of channel distortion, and replacement of lost samples are important parts of a signal processing system. The fourth edition of Advanced Digital Signal Processing and Noise Reduction updates an

  12. Orphan sources

    International Nuclear Information System (INIS)

    Pust, R.; Urbancik, L.

    2008-01-01

    The presentation describes how the stable detection systems (hereinafter referred to as S DS ) have contributed to reveal the uncontrolled sources of ionizing radiation on the territory of the State Office for Nuclear Safety (SONS) Brno Regional Centre (RC Brno). It also describes the emergencies which were solved by or in which the workers from the Brno. Regional Centre participated in. The contribution is divided into the following chapters: A. SDS systems installed on the territory of SONS RC Brno; B. Selected unusual emergencies; C. Comments to individual emergencies; D. Aspects of SDS operation in term of their users; E. Aspects of SDS operation and related activities in term of radiation protection; F. Current state of orphan sources. (authors)

  13. Tritium sources

    International Nuclear Information System (INIS)

    Glodic, S.; Boreli, F.

    1993-01-01

    Tritium is the only radioactive isotope of hydrogen. It directly follows the metabolism of water and it can be bound into genetic material, so it is very important to control levels of contamination. In order to define the state of contamination it is necessary to establish 'zero level', i.e. actual global inventory. The importance of tritium contamination monitoring increases with the development of fusion power installations. Different sources of tritium are analyzed and summarized in this paper. (author)

  14. Radioactive source

    International Nuclear Information System (INIS)

    Drabkina, L.E.; Mazurek, V.; Myascedov, D.N.; Prokhorov, P.; Kachalov, V.A.; Ziv, D.M.

    1976-01-01

    A radioactive layer in a radioactive source is sealed by the application of a sealing layer on the radioactive layer. The sealing layer can consist of a film of oxide of titanium, tin, zirconium, aluminum, or chromium. Preferably, the sealing layer is pure titanium dioxide. The radioactive layer is embedded in a finish enamel which, in turn, is on a priming enamel which surrounds a substrate

  15. Adubação da batata-doce em São Paulo parte IV: experiências comparando formas de N, P e K Fertilizer experiments with sweet potatoes IV: trials with some N, P, and K sources

    Directory of Open Access Journals (Sweden)

    A. Paes de Camargo

    1962-01-01

    Full Text Available De 1943-44 a 1945-46 realizaram-se seis experiências (três anuais, uma conduzida por dois e duas por três anos, em três localidades do Estado de São Paulo, para estudar o efeito, sôbre a batata-doce, de diversas formulas contendo sempre 60-100-40 kg/ha de N-P2O5-K2O, mas preparadas com diferentes adubos nitrogenados, fosfatados e potássicos. Em relação ao tratamento sem adubo, foram poucos os casos em que as adubações com NPK aumentaram substancialmente a produção. Nessas condições, superfosfato se mostrou ligeiramente superior à farinha de ossos e não se notou diferença entre cloreto de potássio e cinzas de café. Sulfato de amônio, que figurou na experiênca conduzida por dois anos, e torta de algodão, nas demais, em regra com portaram-se melhor do que salitre do Chile. Individualmente, as fórmulas mais eficientes foram as preparadas com superfosfato, cloreto de potássio e sulfato de amônio ou torta de algodão. Contudo, mesmo com estas, foi muito baixa a freqüência de resultados compensadores.Six experiments with sweet potatoes were located on two soil types of the State of São Paulo to study the effects of fertilizer mixtures prepared with different, N. P, and K sources, but containing always 60-100-40 kilograms of N-P(20(5-K(20 per hectare. The yield increases of fertilized over the unfertilized plots were satisfactory only in a few of the 11 annual results obtained. Under such poor conditions, superphosphate was slightly superior to bone meal and no difference was observed between coffee ashes and potassium chloride. Ammonium sulphate, in one, and cottonseed meal, in the other five trials, as a rule, were more efficient than Chilean nitrate. Individually, the mixtures prepared with superphosphate, potassium chloride, and ammonium sulphate or cottonseed meal gave the best results but even with them the frequency of satisfactory yield increases was very low.

  16. Muon sources

    International Nuclear Information System (INIS)

    Parsa, Z.

    2001-01-01

    A full high energy muon collider may take considerable time to realize. However, intermediate steps in its direction are possible and could help facilitate the process. Employing an intense muon source to carry out forefront low energy research, such as the search for muon-number non-conservation, represents one interesting possibility. For example, the MECO proposal at BNL aims for 2 x 10 -17 sensitivity in their search for coherent muon-electron conversion in the field of a nucleus. To reach that goal requires the production, capture and stopping of muons at an unprecedented 10 11 μ/sec. If successful, such an effort would significantly advance the state of muon technology. More ambitious ideas for utilizing high intensity muon sources are also being explored. Building a muon storage ring for the purpose of providing intense high energy neutrino beams is particularly exciting.We present an overview of muon sources and example of a muon storage ring based Neutrino Factory at BNL with various detector location possibilities

  17. Pediatric radiology fellows' experience with intussusception reduction

    International Nuclear Information System (INIS)

    Stein-Wexler, Rebecca; Bateni, Cyrus; Wootton-Gorges, Sandra L.; Li, Chin-Shang

    2011-01-01

    Intussusception reduction allows young children to avoid surgery. However, graduating residents have had relatively little training in intussusception reduction and, for the most part, consider themselves ill-prepared to perform this procedure. The goal of this study was to assess the extent of training in intussusception reduction during one year of a pediatric radiology fellowship and to determine whether graduating fellows consider themselves adequately trained in this technique. Pediatric radiology fellows were surveyed during June 2010 and asked to characterize their fellowship, to indicate the number of intussusception reductions performed (both the total number and those performed with faculty oversight but without active faculty involvement), and to assess the adequacy of their training. There were 31 responses, representing almost 1/3 of current fellows. Pediatric radiology fellows perform on average 6.9 reductions, 3.8 of which are with faculty oversight but without active faculty involvement. Ninety percent consider themselves well-trained in the technique, whereas 10% are uncertain (none consider their training inadequate). Almost all pediatric radiology fellows consider their training in intussusception reduction to be adequate. (orig.)

  18. Spontaneous wave packet reduction

    International Nuclear Information System (INIS)

    Ghirardi, G.C.

    1994-06-01

    There are taken into account the main conceptual difficulties met by standard quantum mechanics in dealing with physical processes involving macroscopic system. It is stressed how J.A.Wheeler's remarks and lucid analysis have been relevant to pinpoint and to bring to its extreme consequences the puzzling aspects of quantum phenomena. It is shown how the recently proposed models of spontaneous dynamical reduction represent a consistent way to overcome the conceptual difficulties of the standard theory. Obviously, many nontrivial problems remain open, the first and more relevant one being that of generalizing the model theories considered to the relativistic case. This is the challenge of the dynamical reduction program. 43 refs, 2 figs

  19. Inhibition of sulfate reduction in paddy soils

    Energy Technology Data Exchange (ETDEWEB)

    Vamos, R

    1958-12-13

    The hydrogen sulfide formed in waterlogged soils is a serious problem in rice cultivation. It inhibits the uptake of water and nutrients and may even cause root-rot. Results can best be obtained by preventing the formation of hydrogen sulfide. It is formed mainly by reduction of sulfate for which the cellulose-butyric acid fermentation provides the hydrogen source. Addition of ammonium or potassium nitrate prevents the formation of H/sub 2/S. The hydrogen produced by butyric acid fermentation is used to reduce nitrate and consequently cannot be utilized by the sulfate-reducing bacteria as a source of energy. 6 references.

  20. Industrialisation, Trade Policy and Poverty Reduction: Evidence from Asia

    OpenAIRE

    Peter Warr

    2003-01-01

    Over recent decades, most of the developing economies of Asia achieved reductions in absolute poverty incidence, but these reductions varied greatly in size. Differences in the rate of aggregate economic growth explain part, but not all of these differences. One factor that would be important is the sectoral composition of the growth. This paper examines the relationship between poverty reduction outcomes and the rate of growth in the agricultural, industrial and services sectors. It assemble...

  1. International Requirements for Large Integration of Renewable Energy Sources

    DEFF Research Database (Denmark)

    Molina-Garcia, Angel; Hansen, Anca Daniela; Muljadi, Ed

    2017-01-01

    Most European countries have concerns about the integration of large amounts of renewable energy sources (RES) into electric power systems, and this is currently a topic of growing interest. In January 2008, the European Commission published the 2020 package, which proposes committing the European...... Union to a 20% reduction in greenhouse gas emissions, to achieve a target of deriving 20% of the European Union's final energy consumption from renewable sources, and to achieve 20% improvement in energy efficiency both by the year 2020 [1]. Member states have different individual goals to meet...... these overall objectives, and they each need to provide a detailed roadmap describing how they will meet these legally binding targets [2]. At this time, RES are an indispensable part of the global energy mix, which has been partially motivated by the continuous increases in hydropower as well as the rapid...

  2. BP volume reduction equipment

    International Nuclear Information System (INIS)

    Kitamura, Yoshinori; Muroo, Yoji; Hamanaka, Isao

    2003-01-01

    A new type of burnable poison (BP) volume reduction system is currently being developed. Many BP rods, a subcomponent of spent fuel assemblies are discharged from nuclear power reactors. This new system reduces the overall volume of BP rods. The main system consists of BP rod cutting equipment, equipment for the recovery of BP cut pieces, and special transport equipment for the cut rods. The equipment is all operated by hydraulic press cylinders in water to reduce operator exposure to radioactivity. (author)

  3. Anaerobic azo dye reduction

    OpenAIRE

    Zee, van der, F.P.

    2002-01-01

    Azo dyes, aromatic moieties linked together by azo (-N=N-) chromophores, represent the largest class of dyes used in textile-processing and other industries. The release of these compounds into the environment is undesirable, not only because of their colour, but also because many azo dyes and their breakdown products are toxic and/or mutagenic to life. To remove azo dyes from wastewater, a biological treatment strategy based on anaerobic reduction of the azo dye...

  4. Dose reduction strategies for cardiac CT

    International Nuclear Information System (INIS)

    Midgley, S.M.; Einsiedel, P.; Langenberg, F.; Lui, E.

    2010-01-01

    Full text: Recent advances in CT technology have produced brighter X-ray sources. gantries capable of increased rotation speeds, faster scintil lation materials arranged into multiple rows of detectors, and associated advances in 3D reconstruction methods. These innovations have allowed multi-detector CT to be turned to the diagnosis of cardiac abnormalities and compliment traditional imaging techniques such as coronary angiography. This study examines the cardiac imaging solution offered by the Siemens Somatom Definition Dual Source 64 slice CT scanner. Our dose reduction strategies involve optimising the data acquisition protocols according to diagnostic task, patient size and heart rate. The relationship between scan parameters, image quality and patient dose is examined and verified against measurements with phantoms representing the standard size patient. The dose reduction strategies are reviewed with reference to survey results of patient dose. Some cases allow the insertion of shielding to protect radiosensitive organs, and results are presented to quantify the dose saving.

  5. Thermochemical nitrate reduction

    International Nuclear Information System (INIS)

    Cox, J.L.; Lilga, M.A.; Hallen, R.T.

    1992-09-01

    A series of preliminary experiments was conducted directed at thermochemically converting nitrate to nitrogen and water. Nitrates are a major constituent of the waste stored in the underground tanks on the Hanford Site, and the characteristics and effects of nitrate compounds on stabilization techniques must be considered before permanent disposal operations begin. For the thermochemical reduction experiments, six reducing agents (ammonia, formate, urea, glucose, methane, and hydrogen) were mixed separately with ∼3 wt% NO 3 - solutions in a buffered aqueous solution at high pH (13); ammonia and formate were also mixed at low pH (4). Reactions were conducted in an aqueous solution in a batch reactor at temperatures of 200 degrees C to 350 degrees C and pressures of 600 to 2800 psig. Both gas and liquid samples were analyzed. The specific components analyzed were nitrate, nitrite, nitrous oxide, nitrogen, and ammonia. Results of experimental runs showed the following order of nitrate reduction of the six reducing agents in basic solution: formate > glucose > urea > hydrogen > ammonia ∼ methane. Airnmonia was more effective under acidic conditions than basic conditions. Formate was also effective under acidic conditions. A more thorough, fundamental study appears warranted to provide additional data on the mechanism of nitrate reduction. Furthermore, an expanded data base and engineering feasibility study could be used to evaluate conversion conditions for promising reducing agents in more detail and identify new reducing agents with improved performance characteristics

  6. Evolution of aerosol chemistry in Xi'an, inland China, during the dust storm period of 2013 - Part 1: Sources, chemical forms and formation mechanisms of nitrate and sulfate

    Science.gov (United States)

    Wang, G. H.; Cheng, C. L.; Huang, Y.; Tao, J.; Ren, Y. Q.; Wu, F.; Meng, J. J.; Li, J. J.; Cheng, Y. T.; Cao, J. J.; Liu, S. X.; Zhang, T.; Zhang, R.; Chen, Y. B.

    2014-11-01

    were secondarily produced via this pathway, with the remaining derived from the Gobi desert and Loess Plateau, while SO42- in the event almost entirely originated from the desert regions. Such cases are different from those in the East Asian continental outflow region, where during Asia dust storm events SO42- is secondarily produced and concentrates in sub-micrometer particles as (NH4)2SO4 and/or NH4HSO4. To the best of our knowledge, the current work for the first time revealed an infant state of the East Asian dust ageing process in the regions near the source, which is helpful for researchers to understand the panorama of East Asian dust ageing process from the desert area to the downwind region.

  7. Comparison of order reduction algorithms for application to electrical networks

    Directory of Open Access Journals (Sweden)

    Lj. Radić-Weissenfeld

    2009-05-01

    Full Text Available This paper addresses issues related to the minimization of the computational burden in terms of both memory and speed during the simulation of electrical models. In order to achieve a simple and computational fast model the order reduction of its reducible part is proposed. In this paper the overview of the order reduction algorithms and their application are discussed.

  8. Hanford Site annual waste reduction report

    International Nuclear Information System (INIS)

    Nichols, D.H.

    1992-03-01

    The US Department of Energy (DOE), Richland Field Office (RL) has developed and implemented a Hanford Site Waste Minimization and Pollution Prevention Awareness Plan that provides overall guidance and direction on waste minimization and pollution prevention awareness to the four contractors who manage and operate the Hanford Site for the RL. Waste reduction at the RL will be accomplished by following a hierarchy of environmental protection practices. First, waste generation will be eliminated or minimized through source reduction. Second, potential waste materials that cannot be eliminated or minimized will be recycled (i.e., used, reused, or reclaimed). Third, all waste that is nevertheless generated will be treated to reduce volume, toxicity, or mobility before storage or disposal. The scope of this waste reduction program will include nonhazardous, hazardous, radioactive mixed, and radioactive wastes

  9. Fission product gamma-ray sources as an alternative to cobalt-60 sources for sewage sludge sterilization

    International Nuclear Information System (INIS)

    Herrnberger, V.R.D.

    1975-01-01

    The sterilization of sewage sludge is now performed successfully using 60 Co gamma-ray sources. The question arises whether more economic gamma-ray sources exist that could replace the 60 Co source. The following types of sources are considered: Spent fuel elements; mixtures of solidified fission products; and isolated solidified fission products such as 134 / 137 Cs. For a particular irradiation plant the specific source costs (S.Fr./Ci) and their contribution to the irradiation costs for 1 m 3 of sewage irradiated to a dose of 250 krad(S.Fr./m 3 ) are determined and compared with the costs of a plant using a 60 Co source. The encapsulation costs and the effect of the gamma absorption of the source are taken into account. Different encapsulation and source management techniques are reviewed to find the most economic for each source type. A spent fuel element irradiation facility is recommended for use either in combination with a sewage water purification plant or as part of a power reactor station where it replaces the storage water pool for the spent fuel elements. Additional source capsules are not envisaged, as long as double-walled source containers are used. The fission product mixtures are enclosed in double-walled capsules of two different forms: Small cylindrical rods and hollow cylinders. For caesium and cobalt cylindrical rods only are used. The main conclusions of the study are that the highest irradiation costs arise from the use of a fission product mixture source. The costs are, however, only 15% above those of a 60 Co plant. To be competitive the flow-rate has to be adapted to the decreasing activity of the source, resulting in a reduction to 20% within ten years of source utilization. The integrated irradiation plant with a spent fuel element source offers irradiation costs comparable with those of a 60 Co plant, if the flow-rate is constant during one year of source utilization. The irradiation costs are reduced to 25% of those of a 60 Co plant

  10. Vietnam; Poverty Reduction Strategy Paper

    OpenAIRE

    International Monetary Fund

    2004-01-01

    This paper assesses the Poverty Reduction Strategy Paper of Vietnam, known as the Comprehensive Poverty Reduction and Growth Strategy (CPRGS). It is an action program to achieve economic growth and poverty reduction objectives. This paper reviews the objectives and tasks of socio-economic development and poverty reduction. The government of Vietnam takes poverty reduction as a cutting-through objective in the process of country socio-economic development and declares its commitment to impleme...

  11. PWR Facility Dose Modeling Using MCNP5 and the CADIS/ADVANTG Variance-Reduction Methodology

    Energy Technology Data Exchange (ETDEWEB)

    Blakeman, Edward D [ORNL; Peplow, Douglas E. [ORNL; Wagner, John C [ORNL; Murphy, Brian D [ORNL; Mueller, Don [ORNL

    2007-09-01

    The feasibility of modeling a pressurized-water-reactor (PWR) facility and calculating dose rates at all locations within the containment and adjoining structures using MCNP5 with mesh tallies is presented. Calculations of dose rates resulting from neutron and photon sources from the reactor (operating and shut down for various periods) and the spent fuel pool, as well as for the photon source from the primary coolant loop, were all of interest. Identification of the PWR facility, development of the MCNP-based model and automation of the run process, calculation of the various sources, and development of methods for visually examining mesh tally files and extracting dose rates were all a significant part of the project. Advanced variance reduction, which was required because of the size of the model and the large amount of shielding, was performed via the CADIS/ADVANTG approach. This methodology uses an automatically generated three-dimensional discrete ordinates model to calculate adjoint fluxes from which MCNP weight windows and source bias parameters are generated. Investigative calculations were performed using a simple block model and a simplified full-scale model of the PWR containment, in which the adjoint source was placed in various regions. In general, it was shown that placement of the adjoint source on the periphery of the model provided adequate results for regions reasonably close to the source (e.g., within the containment structure for the reactor source). A modification to the CADIS/ADVANTG methodology was also studied in which a global adjoint source is weighted by the reciprocal of the dose response calculated by an earlier forward discrete ordinates calculation. This method showed improved results over those using the standard CADIS/ADVANTG approach, and its further investigation is recommended for future efforts.

  12. PWR Facility Dose Modeling Using MCNP5 and the CADIS/ADVANTG Variance-Reduction Methodology

    International Nuclear Information System (INIS)

    Blakeman, Edward D.; Peplow, Douglas E.; Wagner, John C.; Murphy, Brian D.; Mueller, Don

    2007-01-01

    The feasibility of modeling a pressurized-water-reactor (PWR) facility and calculating dose rates at all locations within the containment and adjoining structures using MCNP5 with mesh tallies is presented. Calculations of dose rates resulting from neutron and photon sources from the reactor (operating and shut down for various periods) and the spent fuel pool, as well as for the photon source from the primary coolant loop, were all of interest. Identification of the PWR facility, development of the MCNP-based model and automation of the run process, calculation of the various sources, and development of methods for visually examining mesh tally files and extracting dose rates were all a significant part of the project. Advanced variance reduction, which was required because of the size of the model and the large amount of shielding, was performed via the CADIS/ADVANTG approach. This methodology uses an automatically generated three-dimensional discrete ordinates model to calculate adjoint fluxes from which MCNP weight windows and source bias parameters are generated. Investigative calculations were performed using a simple block model and a simplified full-scale model of the PWR containment, in which the adjoint source was placed in various regions. In general, it was shown that placement of the adjoint source on the periphery of the model provided adequate results for regions reasonably close to the source (e.g., within the containment structure for the reactor source). A modification to the CADIS/ADVANTG methodology was also studied in which a global adjoint source is weighted by the reciprocal of the dose response calculated by an earlier forward discrete ordinates calculation. This method showed improved results over those using the standard CADIS/ADVANTG approach, and its further investigation is recommended for future efforts

  13. Waste reduction at the Savannah River Site

    International Nuclear Information System (INIS)

    Stevens, W.E.; Lee, R.A.; Reynolds, R.W.

    1990-01-01

    The Savannah River Site (SRS) is a key installation for the production and research of nuclear materials for national defense and peace time applications and has been operating a full nuclear fuel cycle since the early 1950s. Wastes generated include high level radioactive, transuranic, low level radioactive, hazardous, mixed, sanitary, and aqueous wastes. Much progress has been made during the last several years to reduce these wastes including management systems, characterization, and technology programs. The reduction of wastes generated and the proper handling of the wastes have always been a part of the Site's operation. This paper summarizes the current status and future plans with respect to waste reduction to waste reduction and reviews some specific examples of successful activities

  14. Violence against female sex workers in Cameroon: accounts of violence, harm reduction, and potential solutions.

    Science.gov (United States)

    Lim, Sahnah; Peitzmeier, Sarah; Cange, Charles; Papworth, Erin; LeBreton, Matthew; Tamoufe, Ubald; Kamla, Aristide; Billong, Serge; Fokam, Pamella; Njindam, Iliassou; Decker, Michele R; Sherman, Susan G; Baral, Stefan

    2015-03-01

    Female sex workers (FSWs) in Cameroon, and West Africa generally, suffer a disproportionate burden of HIV. Although violence against FSWs has been documented extensively in other parts of the world, data on violence from West African countries are lacking. The aim of this study was to qualitatively document violence and harm reduction strategies from the perspective of FSWs in Cameroon as well as to understand how experiences of violence may increase FSWs' HIV risk. FSWs from 7 major cities in Cameroon (Douala, Yaounde, Bamenda, Bertoua, Nagoundere, Kribi, and Bafoussam) were purposively recruited. Data from 31 in-depth interviews and 7 focus groups (n = 70; with some overlapping participants from in-depth interviews) conducted with these FSWs in 6 of these 7 cities (excluding Kribi) were analyzed using a grounded theory approach. Transcripts revealed 3 primary themes related to violence: (1) sources and types of violence, including sexual, physical, and financial violence perpetrated by clients and police, (2) harm reduction strategies, including screening clients and safe work locations, receipt of payment before sexual act, and formation of an informal security network, and (3) recommendations on structural changes to reduce violence that emphasized sex work decriminalization and increased police accountability. As in other parts of the world, violence against FSWs is pervasive in Cameroon. Interventions targeting violence and HIV must address the forms of violence cited locally by FSWs and can build on FSWs' existing strengths and harm reduction strategies. Structural changes are needed to ensure access to justice for this population.

  15. Discrete Routh reduction

    International Nuclear Information System (INIS)

    Jalnapurkar, Sameer M; Leok, Melvin; Marsden, Jerrold E; West, Matthew

    2006-01-01

    This paper develops the theory of Abelian Routh reduction for discrete mechanical systems and applies it to the variational integration of mechanical systems with Abelian symmetry. The reduction of variational Runge-Kutta discretizations is considered, as well as the extent to which symmetry reduction and discretization commute. These reduced methods allow the direct simulation of dynamical features such as relative equilibria and relative periodic orbits that can be obscured or difficult to identify in the unreduced dynamics. The methods are demonstrated for the dynamics of an Earth orbiting satellite with a non-spherical J 2 correction, as well as the double spherical pendulum. The J 2 problem is interesting because in the unreduced picture, geometric phases inherent in the model and those due to numerical discretization can be hard to distinguish, but this issue does not appear in the reduced algorithm, where one can directly observe interesting dynamical structures in the reduced phase space (the cotangent bundle of shape space), in which the geometric phases have been removed. The main feature of the double spherical pendulum example is that it has a non-trivial magnetic term in its reduced symplectic form. Our method is still efficient as it can directly handle the essential non-canonical nature of the symplectic structure. In contrast, a traditional symplectic method for canonical systems could require repeated coordinate changes if one is evoking Darboux' theorem to transform the symplectic structure into canonical form, thereby incurring additional computational cost. Our method allows one to design reduced symplectic integrators in a natural way, despite the non-canonical nature of the symplectic structure

  16. Pediatricians working part-time: past, present, and future.

    Science.gov (United States)

    Cull, William L; Mulvey, Holly J; O'Connor, Karen G; Sowell, Debra R; Berkowitz, Carol D; Britton, Carmelita V

    2002-06-01

    Pediatrics has consistently attracted a large number of women. Although the majority of practicing pediatricians are male, female pediatricians will soon constitute the majority. The challenge to balance personal and professional life is of particular concern to women, and part-time positions may provide a potential solution. To examine how many pediatricians currently work part-time, to examine trends in part-time employment from 1993 to present, to determine pediatric residents' interest in part-time employment, and to identify perceived barriers to part-time work. Two data sources were used for these analyses. The first was an American Academy of Pediatrics Periodic Survey from 1993 and 2000 asking a combined national sample of 3218 American Academy of Pediatrics members about their employment status. Multiple mailings were conducted for each survey producing an overall response rate of 62%. The second data source was a survey asking a national random sample of 500 pediatric residents completing training in 2000 about their job search experiences and attitudes toward part-time employment. Four mailings of this survey were completed, and responses were obtained from 71% of residents. The percentage of pediatricians working part-time increased from 11% in 1993 to 15% in 2000. This increase did not exceed what would be expected based on the rise in the percentage of pediatricians who are female from 36% in 1993 to 45% in 2000. On average, pediatricians working part-time provided 36% fewer direct patient care hours than full-time pediatricians (42 hours vs 27 hours). No statistically significant difference in direct patient care hours was apparent between male and female pediatricians working full-time. Female residents were more likely than male residents to consider part-time or reduced-hours positions (42% vs 14%) and to accept part-time or reduced-hours positions (14% vs 3%). Also, considerably more female residents (58%) than male residents (15%) indicated that

  17. Editorial: Open Source in Government

    Directory of Open Access Journals (Sweden)

    Dru Lavigne

    2009-04-01

    Full Text Available Last summer, the Center for Strategic and International Studies published the sixth update to their Open Source Policy survey. The survey "tracks governmental policies on the use of open source software as reported in the press or other media." The report lists 275 open source policy initiatives. It also breaks down by country and by government level whether the policy on the use of open source is considered to be advisory, preferential, or mandatory. The editorial theme for the May issue of the OSBR is "open source in government" and we are pleased that the authors have drawn upon their experiences to provide insight into public policy regarding open source for many parts of the world.

  18. Energy Savings from Industrial Water Reductions

    Energy Technology Data Exchange (ETDEWEB)

    Rao, Prakash; McKane, Aimee; de Fontaine, Andre

    2015-08-03

    Although it is widely recognized that reducing freshwater consumption is of critical importance, generating interest in industrial water reduction programs can be hindered for a variety of reasons. These include the low cost of water, greater focus on water use in other sectors such as the agriculture and residential sectors, high levels of unbilled and/or unregulated self-supplied water use in industry, and lack of water metering and tracking capabilities at industrial facilities. However, there are many additional components to the resource savings associated with reducing site water use beyond the water savings alone, such as reductions in energy consumption, greenhouse gas emissions, treatment chemicals, and impact on the local watershed. Understanding and quantifying these additional resource savings can expand the community of businesses, NGOs, government agencies, and researchers with a vested interest in water reduction. This paper will develop a methodology for evaluating the embedded energy consumption associated with water use at an industrial facility. The methodology developed will use available data and references to evaluate the energy consumption associated with water supply and wastewater treatment outside of a facility’s fence line for various water sources. It will also include a framework for evaluating the energy consumption associated with water use within a facility’s fence line. The methodology will develop a more complete picture of the total resource savings associated with water reduction efforts and allow industrial water reduction programs to assess the energy and CO2 savings associated with their efforts.

  19. Preventing industrial pollution at its source: the final report of the Michigan source reduction initiative

    Energy Technology Data Exchange (ETDEWEB)

    None

    1999-09-01

    This report describes a collaborative effort between NRDC, Dow Chemical, and Michigan Environmental Groups. The effort resulted in the identification and implementation of 17 pollution prevention projects that reduced substantial quantities of wastes and emissions and saved Dow considerable money.

  20. Preventing industrial pollution at its source: the final report of the Michigan source reduction initiative; FINAL

    International Nuclear Information System (INIS)

    None

    1999-01-01

    This report describes a collaborative effort between NRDC, Dow Chemical, and Michigan Environmental Groups. The effort resulted in the identification and implementation of 17 pollution prevention projects that reduced substantial quantities of wastes and emissions and saved Dow considerable money